1 files changed, 84 insertions, 9 deletions

diff --git a/drivers/iio/accel/bmc150-accel.h b/drivers/iio/accel/bmc150-accel.h
index ae6118ae11b1..e8f26198359f 100644
--- a/drivers/iio/accel/bmc150-accel.h
+++ b/drivers/iio/accel/bmc150-accel.h
@@ -2,20 +2,95 @@
 #ifndef _BMC150_ACCEL_H_
 #define _BMC150_ACCEL_H_
 
+#include <linux/atomic.h>
+#include <linux/iio/iio.h>
+#include <linux/mutex.h>
+#include <linux/regulator/consumer.h>
+#include <linux/types.h>
+#include <linux/workqueue.h>
+
 struct regmap;
+struct i2c_client;
+struct bmc150_accel_chip_info;
+struct bmc150_accel_interrupt_info;
+
+/*
+ * We can often guess better than "UNKNOWN" based on the device IDs
+ * but unfortunately this information is not always accurate. There are some
+ * devices where ACPI firmware specifies an ID like "BMA250E" when the device
+ * actually has a BMA222E. The driver attempts to detect those by reading the
+ * chip ID from the registers but this information is not always enough either.
+ *
+ * Therefore, this enum should be only used when the chip ID detection is not
+ * enough and we can be reasonably sure that the device IDs are reliable
+ * in practice (e.g. for device tree platforms).
+ */
+enum bmc150_type {
+	BOSCH_UNKNOWN,
+	BOSCH_BMC156,
+};
+
+struct bmc150_accel_interrupt {
+	const struct bmc150_accel_interrupt_info *info;
+	atomic_t users;
+};
+
+struct bmc150_accel_trigger {
+	struct bmc150_accel_data *data;
+	struct iio_trigger *indio_trig;
+	int (*setup)(struct bmc150_accel_trigger *t, bool state);
+	int intr;
+	bool enabled;
+};
+
+enum bmc150_accel_interrupt_id {
+	BMC150_ACCEL_INT_DATA_READY,
+	BMC150_ACCEL_INT_ANY_MOTION,
+	BMC150_ACCEL_INT_WATERMARK,
+	BMC150_ACCEL_INTERRUPTS,
+};
+
+enum bmc150_accel_trigger_id {
+	BMC150_ACCEL_TRIGGER_DATA_READY,
+	BMC150_ACCEL_TRIGGER_ANY_MOTION,
+	BMC150_ACCEL_TRIGGERS,
+};
 
-enum {
-	bmc150,
-	bmi055,
-	bma255,
-	bma250e,
-	bma222e,
-	bma280,
+struct bmc150_accel_data {
+	struct regmap *regmap;
+	int irq;
+	struct regulator_bulk_data regulators[2];
+	struct bmc150_accel_interrupt interrupts[BMC150_ACCEL_INTERRUPTS];
+	struct bmc150_accel_trigger triggers[BMC150_ACCEL_TRIGGERS];
+	struct mutex mutex;
+	u8 fifo_mode, watermark;
+	s16 buffer[8];
+	/*
+	 * Ensure there is sufficient space and correct alignment for
+	 * the timestamp if enabled
+	 */
+	struct {
+		__le16 channels[3];
+		aligned_s64 ts;
+	} scan;
+	u8 bw_bits;
+	u32 slope_dur;
+	u32 slope_thres;
+	u32 range;
+	int ev_enable_state;
+	int64_t timestamp, old_timestamp; /* Only used in hw fifo mode. */
+	const struct bmc150_accel_chip_info *chip_info;
+	enum bmc150_type type;
+	struct i2c_client *second_device;
+	void (*resume_callback)(struct device *dev);
+	struct delayed_work resume_work;
+	struct iio_mount_matrix orientation;
 };
 
 int bmc150_accel_core_probe(struct device *dev, struct regmap *regmap, int irq,
-			    const char *name, bool block_supported);
-int bmc150_accel_core_remove(struct device *dev);
+			    enum bmc150_type type, const char *name,
+			    bool block_supported);
+void bmc150_accel_core_remove(struct device *dev);
 extern const struct dev_pm_ops bmc150_accel_pm_ops;
 extern const struct regmap_config bmc150_regmap_conf;