diff options
Diffstat (limited to 'drivers/iio/pressure/bmp280.h')
| -rw-r--r-- | drivers/iio/pressure/bmp280.h | 388 |
1 files changed, 366 insertions, 22 deletions
diff --git a/drivers/iio/pressure/bmp280.h b/drivers/iio/pressure/bmp280.h index c791325c7416..25bb9c743a05 100644 --- a/drivers/iio/pressure/bmp280.h +++ b/drivers/iio/pressure/bmp280.h @@ -2,6 +2,122 @@ #include <linux/bitops.h> #include <linux/device.h> #include <linux/regmap.h> +#include <linux/regulator/consumer.h> + +#include <linux/iio/iio.h> + +/* BMP580 specific registers */ +#define BMP580_REG_CMD 0x7E +#define BMP580_REG_EFF_OSR 0x38 +#define BMP580_REG_ODR_CONFIG 0x37 +#define BMP580_REG_OSR_CONFIG 0x36 +#define BMP580_REG_IF_CONFIG 0x13 +#define BMP580_REG_REV_ID 0x02 +#define BMP580_REG_CHIP_ID 0x01 +/* OOR allows to configure a pressure alarm */ +#define BMP580_REG_OOR_CONFIG 0x35 +#define BMP580_REG_OOR_RANGE 0x34 +#define BMP580_REG_OOR_THR_MSB 0x33 +#define BMP580_REG_OOR_THR_LSB 0x32 +/* DSP registers (IIR filters) */ +#define BMP580_REG_DSP_IIR 0x31 +#define BMP580_REG_DSP_CONFIG 0x30 +/* NVM access registers */ +#define BMP580_REG_NVM_DATA_MSB 0x2D +#define BMP580_REG_NVM_DATA_LSB 0x2C +#define BMP580_REG_NVM_ADDR 0x2B +/* Status registers */ +#define BMP580_REG_STATUS 0x28 +#define BMP580_REG_INT_STATUS 0x27 +#define BMP580_REG_CHIP_STATUS 0x11 +/* Data registers */ +#define BMP580_REG_FIFO_DATA 0x29 +#define BMP580_REG_PRESS_MSB 0x22 +#define BMP580_REG_PRESS_LSB 0x21 +#define BMP580_REG_PRESS_XLSB 0x20 +#define BMP580_REG_TEMP_MSB 0x1F +#define BMP580_REG_TEMP_LSB 0x1E +#define BMP580_REG_TEMP_XLSB 0x1D +/* FIFO config registers */ +#define BMP580_REG_FIFO_SEL 0x18 +#define BMP580_REG_FIFO_COUNT 0x17 +#define BMP580_REG_FIFO_CONFIG 0x16 +/* Interruptions config registers */ +#define BMP580_REG_INT_SOURCE 0x15 +#define BMP580_REG_INT_CONFIG 0x14 + +#define BMP580_CMD_NOOP 0x00 +#define BMP580_CMD_EXTMODE_SEQ_0 0x73 +#define BMP580_CMD_EXTMODE_SEQ_1 0xB4 +#define BMP580_CMD_EXTMODE_SEQ_2 0x69 +#define BMP580_CMD_NVM_OP_SEQ_0 0x5D +#define BMP580_CMD_NVM_READ_SEQ_1 0xA5 +#define BMP580_CMD_NVM_WRITE_SEQ_1 0xA0 +#define BMP580_CMD_SOFT_RESET 0xB6 + +#define BMP580_INT_STATUS_DRDY_MASK BIT(0) +#define BMP580_INT_STATUS_POR_MASK BIT(4) + +#define BMP580_INT_SOURCE_DRDY BIT(0) + +#define BMP580_INT_CONFIG_MASK GENMASK(3, 0) +#define BMP580_INT_CONFIG_LATCH BIT(0) +#define BMP580_INT_CONFIG_LEVEL BIT(1) +#define BMP580_INT_CONFIG_OPEN_DRAIN BIT(2) +#define BMP580_INT_CONFIG_INT_EN BIT(3) + +#define BMP580_STATUS_CORE_RDY_MASK BIT(0) +#define BMP580_STATUS_NVM_RDY_MASK BIT(1) +#define BMP580_STATUS_NVM_ERR_MASK BIT(2) +#define BMP580_STATUS_NVM_CMD_ERR_MASK BIT(3) + +#define BMP580_OSR_PRESS_MASK GENMASK(5, 3) +#define BMP580_OSR_TEMP_MASK GENMASK(2, 0) +#define BMP580_OSR_PRESS_EN BIT(6) +#define BMP580_EFF_OSR_PRESS_MASK GENMASK(5, 3) +#define BMP580_EFF_OSR_TEMP_MASK GENMASK(2, 0) +#define BMP580_EFF_OSR_VALID_ODR BIT(7) + +#define BMP580_ODR_MASK GENMASK(6, 2) +#define BMP580_MODE_MASK GENMASK(1, 0) +#define BMP580_MODE_SLEEP 0 +#define BMP580_MODE_NORMAL 1 +#define BMP580_MODE_FORCED 2 +#define BMP580_MODE_CONTINOUS 3 +#define BMP580_ODR_DEEPSLEEP_DIS BIT(7) + +#define BMP580_DSP_COMP_MASK GENMASK(1, 0) +#define BMP580_DSP_COMP_DIS 0 +#define BMP580_DSP_TEMP_COMP_EN 1 +/* + * In section 7.27 of datasheet, modes 2 and 3 are technically the same. + * Pressure compensation means also enabling temperature compensation + */ +#define BMP580_DSP_PRESS_COMP_EN 2 +#define BMP580_DSP_PRESS_TEMP_COMP_EN 3 +#define BMP580_DSP_IIR_FORCED_FLUSH BIT(2) +#define BMP580_DSP_SHDW_IIR_TEMP_EN BIT(3) +#define BMP580_DSP_FIFO_IIR_TEMP_EN BIT(4) +#define BMP580_DSP_SHDW_IIR_PRESS_EN BIT(5) +#define BMP580_DSP_FIFO_IIR_PRESS_EN BIT(6) +#define BMP580_DSP_OOR_IIR_PRESS_EN BIT(7) + +#define BMP580_DSP_IIR_PRESS_MASK GENMASK(5, 3) +#define BMP580_DSP_IIR_TEMP_MASK GENMASK(2, 0) +#define BMP580_FILTER_OFF 0 +#define BMP580_FILTER_1X 1 +#define BMP580_FILTER_3X 2 +#define BMP580_FILTER_7X 3 +#define BMP580_FILTER_15X 4 +#define BMP580_FILTER_31X 5 +#define BMP580_FILTER_63X 6 +#define BMP580_FILTER_127X 7 + +#define BMP580_NVM_ROW_ADDR_MASK GENMASK(5, 0) +#define BMP580_NVM_PROG_EN BIT(6) + +#define BMP580_TEMP_SKIPPED 0x7f7f7f +#define BMP580_PRESS_SKIPPED 0x7f7f7f /* BMP380 specific registers */ #define BMP380_REG_CMD 0x7E @@ -63,6 +179,19 @@ #define BMP380_MODE_FORCED 1 #define BMP380_MODE_NORMAL 3 +#define BMP380_MEAS_OFFSET 234 +#define BMP380_MEAS_DUR 2020 +#define BMP380_TEMP_MEAS_OFFSET 163 +#define BMP380_PRESS_MEAS_OFFSET 392 + +#define BMP380_INT_STATUS_DRDY BIT(3) + +#define BMP380_INT_CTRL_SETTINGS_MASK GENMASK(2, 0) +#define BMP380_INT_CTRL_OPEN_DRAIN BIT(0) +#define BMP380_INT_CTRL_LEVEL BIT(1) +#define BMP380_INT_CTRL_LATCH BIT(2) +#define BMP380_INT_CTRL_DRDY_EN BIT(6) + #define BMP380_MIN_TEMP -4000 #define BMP380_MAX_TEMP 8500 #define BMP380_MIN_PRES 3000000 @@ -85,8 +214,6 @@ #define BMP380_PRESS_SKIPPED 0x800000 /* BMP280 specific registers */ -#define BMP280_REG_HUMIDITY_LSB 0xFE -#define BMP280_REG_HUMIDITY_MSB 0xFD #define BMP280_REG_TEMP_XLSB 0xFC #define BMP280_REG_TEMP_LSB 0xFB #define BMP280_REG_TEMP_MSB 0xFA @@ -100,15 +227,10 @@ #define BMP280_REG_CONFIG 0xF5 #define BMP280_REG_CTRL_MEAS 0xF4 #define BMP280_REG_STATUS 0xF3 -#define BMP280_REG_CTRL_HUMIDITY 0xF2 - -/* Due to non linear mapping, and data sizes we can't do a bulk read */ -#define BMP280_REG_COMP_H1 0xA1 -#define BMP280_REG_COMP_H2 0xE1 -#define BMP280_REG_COMP_H3 0xE3 -#define BMP280_REG_COMP_H4 0xE4 -#define BMP280_REG_COMP_H5 0xE5 -#define BMP280_REG_COMP_H6 0xE7 +#define BMP280_REG_STATUS_IM_UPDATE BIT(0) +#define BMP280_REG_STATUS_MEAS_BIT BIT(3) +#define BMP280_REG_RESET 0xE0 +#define BMP280_RST_SOFT_CMD 0xB6 #define BMP280_REG_COMP_TEMP_START 0x88 #define BMP280_COMP_TEMP_REG_COUNT 6 @@ -116,8 +238,6 @@ #define BMP280_REG_COMP_PRESS_START 0x8E #define BMP280_COMP_PRESS_REG_COUNT 18 -#define BMP280_COMP_H5_MASK GENMASK(15, 4) - #define BMP280_CONTIGUOUS_CALIB_REGS (BMP280_COMP_TEMP_REG_COUNT + \ BMP280_COMP_PRESS_REG_COUNT) @@ -128,14 +248,6 @@ #define BMP280_FILTER_8X 3 #define BMP280_FILTER_16X 4 -#define BMP280_OSRS_HUMIDITY_MASK GENMASK(2, 0) -#define BMP280_OSRS_HUMIDITY_SKIP 0 -#define BMP280_OSRS_HUMIDITY_1X 1 -#define BMP280_OSRS_HUMIDITY_2X 2 -#define BMP280_OSRS_HUMIDITY_4X 3 -#define BMP280_OSRS_HUMIDITY_8X 4 -#define BMP280_OSRS_HUMIDITY_16X 5 - #define BMP280_OSRS_TEMP_MASK GENMASK(7, 5) #define BMP280_OSRS_TEMP_SKIP 0 #define BMP280_OSRS_TEMP_1X 1 @@ -157,6 +269,39 @@ #define BMP280_MODE_FORCED 1 #define BMP280_MODE_NORMAL 3 +#define BMP280_MEAS_OFFSET 1250 +#define BMP280_MEAS_DUR 2300 +#define BMP280_PRESS_HUMID_MEAS_OFFSET 575 + +/* BME280 specific registers */ +#define BME280_REG_HUMIDITY_LSB 0xFE +#define BME280_REG_HUMIDITY_MSB 0xFD + +#define BME280_REG_CTRL_HUMIDITY 0xF2 + +/* Due to non linear mapping, and data sizes we can't do a bulk read */ +#define BME280_REG_COMP_H1 0xA1 +#define BME280_REG_COMP_H2 0xE1 +#define BME280_REG_COMP_H3 0xE3 +#define BME280_REG_COMP_H4 0xE4 +#define BME280_REG_COMP_H5 0xE5 +#define BME280_REG_COMP_H6 0xE7 + +#define BME280_COMP_H4_GET_MASK_UP GENMASK(15, 8) +#define BME280_COMP_H4_PREP_MASK_UP GENMASK(11, 4) +#define BME280_COMP_H4_MASK_LOW GENMASK(3, 0) +#define BME280_COMP_H5_MASK GENMASK(15, 4) + +#define BME280_CONTIGUOUS_CALIB_REGS 7 + +#define BME280_OSRS_HUMIDITY_MASK GENMASK(2, 0) +#define BME280_OSRS_HUMIDITY_SKIP 0 +#define BME280_OSRS_HUMIDITY_1X 1 +#define BME280_OSRS_HUMIDITY_2X 2 +#define BME280_OSRS_HUMIDITY_4X 3 +#define BME280_OSRS_HUMIDITY_8X 4 +#define BME280_OSRS_HUMIDITY_16X 5 + /* BMP180 specific registers */ #define BMP180_REG_OUT_XLSB 0xF8 #define BMP180_REG_OUT_LSB 0xF7 @@ -181,8 +326,11 @@ #define BMP280_REG_ID 0xD0 #define BMP380_CHIP_ID 0x50 +#define BMP580_CHIP_ID 0x50 +#define BMP580_CHIP_ID_ALT 0x51 #define BMP180_CHIP_ID 0x55 #define BMP280_CHIP_ID 0x58 +#define BMP390_CHIP_ID 0x60 #define BME280_CHIP_ID 0x60 #define BMP280_SOFT_RESET_VAL 0xB6 @@ -191,15 +339,211 @@ #define BMP280_PRESS_SKIPPED 0x80000 #define BMP280_HUMIDITY_SKIPPED 0x8000 +/* Number of bytes for each value */ +#define BMP280_NUM_PRESS_BYTES 3 +#define BMP280_NUM_TEMP_BYTES 3 +#define BME280_NUM_HUMIDITY_BYTES 2 +#define BMP280_BURST_READ_BYTES (BMP280_NUM_PRESS_BYTES + \ + BMP280_NUM_TEMP_BYTES) +#define BME280_BURST_READ_BYTES (BMP280_NUM_PRESS_BYTES + \ + BMP280_NUM_TEMP_BYTES + \ + BME280_NUM_HUMIDITY_BYTES) + +/* Core exported structs */ + +static const char *const bmp280_supply_names[] = { + "vddd", "vdda" +}; + +#define BMP280_NUM_SUPPLIES ARRAY_SIZE(bmp280_supply_names) + +struct bmp180_calib { + s16 AC1; + s16 AC2; + s16 AC3; + u16 AC4; + u16 AC5; + u16 AC6; + s16 B1; + s16 B2; + s16 MB; + s16 MC; + s16 MD; +}; + +/* See datasheet Section 4.2.2. */ +struct bmp280_calib { + u16 T1; + s16 T2; + s16 T3; + u16 P1; + s16 P2; + s16 P3; + s16 P4; + s16 P5; + s16 P6; + s16 P7; + s16 P8; + s16 P9; + u8 H1; + s16 H2; + u8 H3; + s16 H4; + s16 H5; + s8 H6; +}; + +/* See datasheet Section 3.11.1. */ +struct bmp380_calib { + u16 T1; + u16 T2; + s8 T3; + s16 P1; + s16 P2; + s8 P3; + s8 P4; + u16 P5; + u16 P6; + s8 P7; + s8 P8; + s16 P9; + s8 P10; + s8 P11; +}; + +enum bmp280_op_mode { + BMP280_SLEEP, + BMP280_FORCED, + BMP280_NORMAL, +}; + +struct bmp280_data { + struct device *dev; + struct mutex lock; + struct regmap *regmap; + struct completion done; + bool use_eoc; + bool trig_open_drain; + bool trig_active_high; + struct iio_trigger *trig; + const struct bmp280_chip_info *chip_info; + union { + struct bmp180_calib bmp180; + struct bmp280_calib bmp280; + struct bmp380_calib bmp380; + } calib; + struct regulator_bulk_data supplies[BMP280_NUM_SUPPLIES]; + unsigned int start_up_time_us; + + /* log of base 2 of oversampling rate */ + u8 oversampling_press; + u8 oversampling_temp; + u8 oversampling_humid; + u8 iir_filter_coeff; + + /* + * BMP380 devices introduce sampling frequency configuration. See + * datasheet sections 3.3.3. and 4.3.19 for more details. + * + * BMx280 devices allowed indirect configuration of sampling frequency + * changing the t_standby duration between measurements, as detailed on + * section 3.6.3 of the datasheet. + */ + int sampling_freq; + + /* Value to hold the current operation mode of the device */ + enum bmp280_op_mode op_mode; + + /* + * DMA (thus cache coherency maintenance) may require the + * transfer buffers to live in their own cache lines. + */ + union { + /* Sensor data buffer */ + u8 buf[BME280_BURST_READ_BYTES]; + /* Calibration data buffers */ + __le16 bmp280_cal_buf[BMP280_CONTIGUOUS_CALIB_REGS / sizeof(__le16)]; + __be16 bmp180_cal_buf[BMP180_REG_CALIB_COUNT / sizeof(__be16)]; + u8 bme280_humid_cal_buf[BME280_CONTIGUOUS_CALIB_REGS]; + u8 bmp380_cal_buf[BMP380_CALIB_REG_COUNT]; + /* Miscellaneous, endianness-aware data buffers */ + __le16 le16; + __be16 be16; + } __aligned(IIO_DMA_MINALIGN); +}; + +struct bmp280_chip_info { + unsigned int id_reg; + const u8 *chip_id; + int num_chip_id; + + const struct regmap_config *regmap_config; + bool spi_read_extra_byte; + + const struct iio_chan_spec *channels; + int num_channels; + unsigned int start_up_time_us; + const unsigned long *avail_scan_masks; + + const int *oversampling_temp_avail; + int num_oversampling_temp_avail; + int oversampling_temp_default; + + const int *oversampling_press_avail; + int num_oversampling_press_avail; + int oversampling_press_default; + + const int *oversampling_humid_avail; + int num_oversampling_humid_avail; + int oversampling_humid_default; + + const int *iir_filter_coeffs_avail; + int num_iir_filter_coeffs_avail; + int iir_filter_coeff_default; + + const int (*sampling_freq_avail)[2]; + int num_sampling_freq_avail; + int sampling_freq_default; + + const int *temp_coeffs; + const int temp_coeffs_type; + const int *press_coeffs; + const int press_coeffs_type; + const int *humid_coeffs; + const int humid_coeffs_type; + + int (*chip_config)(struct bmp280_data *data); + int (*read_temp)(struct bmp280_data *data, s32 *adc_temp); + int (*read_press)(struct bmp280_data *data, u32 *adc_press); + int (*read_humid)(struct bmp280_data *data, u32 *adc_humidity); + int (*read_calib)(struct bmp280_data *data); + int (*preinit)(struct bmp280_data *data); + int (*set_mode)(struct bmp280_data *data, enum bmp280_op_mode mode); + int (*wait_conv)(struct bmp280_data *data); + + int (*trigger_probe)(struct iio_dev *indio_dev); + irqreturn_t (*trigger_handler)(int irq, void *p); +}; + +/* Chip infos for each variant */ +extern const struct bmp280_chip_info bmp085_chip_info; +extern const struct bmp280_chip_info bmp180_chip_info; +extern const struct bmp280_chip_info bmp280_chip_info; +extern const struct bmp280_chip_info bme280_chip_info; +extern const struct bmp280_chip_info bmp380_chip_info; +extern const struct bmp280_chip_info bmp580_chip_info; + /* Regmap configurations */ extern const struct regmap_config bmp180_regmap_config; extern const struct regmap_config bmp280_regmap_config; +extern const struct regmap_config bme280_regmap_config; extern const struct regmap_config bmp380_regmap_config; +extern const struct regmap_config bmp580_regmap_config; /* Probe called from different transports */ int bmp280_common_probe(struct device *dev, struct regmap *regmap, - unsigned int chip, + const struct bmp280_chip_info *chip_info, const char *name, int irq); |