diff options
Diffstat (limited to 'drivers/input/keyboard/Kconfig')
| -rw-r--r-- | drivers/input/keyboard/Kconfig | 376 |
1 files changed, 258 insertions, 118 deletions
diff --git a/drivers/input/keyboard/Kconfig b/drivers/input/keyboard/Kconfig index 269d4c3658cb..2ff4fef322c2 100644 --- a/drivers/input/keyboard/Kconfig +++ b/drivers/input/keyboard/Kconfig @@ -1,8 +1,9 @@ +# SPDX-License-Identifier: GPL-2.0-only # # Input core configuration # menuconfig INPUT_KEYBOARD - bool "Keyboards" if EXPERT || !X86 + bool "Keyboards" default y help Say Y here, and a list of supported keyboards will be displayed. @@ -12,6 +13,20 @@ menuconfig INPUT_KEYBOARD if INPUT_KEYBOARD +config KEYBOARD_ADC + tristate "ADC Ladder Buttons" + depends on IIO + help + This driver implements support for buttons connected + to an ADC using a resistor ladder. + + Say Y here if your device has such buttons connected to an ADC. Your + board-specific setup logic must also provide a configuration data + for mapping voltages to buttons. + + To compile this driver as a module, choose M here: the + module will be called adc_keys. + config KEYBOARD_ADP5520 tristate "Keypad Support for ADP5520 PMIC" depends on PMIC_ADP5520 @@ -22,25 +37,29 @@ config KEYBOARD_ADP5520 To compile this driver as a module, choose M here: the module will be called adp5520-keys. -config KEYBOARD_ADP5588 - tristate "ADP5588/87 I2C QWERTY Keypad and IO Expander" - depends on I2C +config KEYBOARD_ADP5585 + tristate "ADP558x keypad support" + depends on MFD_ADP5585 + select INPUT_MATRIXKMAP help - Say Y here if you want to use a ADP5588/87 attached to your - system I2C bus. + This option enables support for the KEYPAD function found in the Analog + Devices ADP5585 and similar devices. To compile this driver as a module, choose M here: the - module will be called adp5588-keys. + module will be called adp5585-keys. -config KEYBOARD_ADP5589 - tristate "ADP5585/ADP5589 I2C QWERTY Keypad and IO Expander" +config KEYBOARD_ADP5588 + tristate "ADP5588/87 I2C QWERTY Keypad and IO Expander" depends on I2C + select GPIOLIB + select GPIOLIB_IRQCHIP + select INPUT_MATRIXKMAP help - Say Y here if you want to use a ADP5585/ADP5589 attached to your + Say Y here if you want to use a ADP5588/87 attached to your system I2C bus. To compile this driver as a module, choose M here: the - module will be called adp5589-keys. + module will be called adp5588-keys. config KEYBOARD_AMIGA tristate "Amiga keyboard" @@ -52,8 +71,23 @@ config KEYBOARD_AMIGA To compile this driver as a module, choose M here: the module will be called amikbd. -config ATARI_KBD_CORE - bool +config KEYBOARD_APPLESPI + tristate "Apple SPI keyboard and trackpad" + depends on ACPI && EFI + depends on SPI + depends on X86 || COMPILE_TEST + depends on LEDS_CLASS + select CRC16 + help + Say Y here if you are running Linux on any Apple MacBook8,1 or later, + or any MacBookPro13,* or MacBookPro14,*. + + You will also need to enable appropriate SPI master controllers: + spi_pxa2xx_platform and spi_pxa2xx_pci for MacBook8,1, and + spi_pxa2xx_platform and intel_lpss_pci for the rest. + + To compile this driver as a module, choose M here: the + module will be called applespi. config KEYBOARD_ATARI tristate "Atari keyboard" @@ -67,12 +101,13 @@ config KEYBOARD_ATARI module will be called atakbd. config KEYBOARD_ATKBD - tristate "AT keyboard" if EXPERT || !X86 + tristate "AT keyboard" default y select SERIO select SERIO_LIBPS2 - select SERIO_I8042 if X86 + select SERIO_I8042 if ARCH_MIGHT_HAVE_PC_SERIO select SERIO_GSCPS2 if GSC + select INPUT_VIVALDIFMAP help Say Y here if you want to use a standard AT or PS/2 keyboard. Usually you'll need this, unless you have a different type keyboard (USB, ADB @@ -122,15 +157,26 @@ config KEYBOARD_ATKBD_RDI_KEYCODES right-hand column will be interpreted as the key shown in the left-hand column. +config KEYBOARD_QT1050 + tristate "Microchip AT42QT1050 Touch Sensor Chip" + depends on I2C + select REGMAP_I2C + help + Say Y here if you want to use Microchip AT42QT1050 QTouch + Sensor chip as input device. + + To compile this driver as a module, choose M here: + the module will be called qt1050 + config KEYBOARD_QT1070 - tristate "Atmel AT42QT1070 Touch Sensor Chip" - depends on I2C - help - Say Y here if you want to use Atmel AT42QT1070 QTouch - Sensor chip as input device. + tristate "Atmel AT42QT1070 Touch Sensor Chip" + depends on I2C + help + Say Y here if you want to use Atmel AT42QT1070 QTouch + Sensor chip as input device. - To compile this driver as a module, choose M here: - the module will be called qt1070 + To compile this driver as a module, choose M here: + the module will be called qt1070 config KEYBOARD_QT2160 tristate "Atmel AT42QT2160 Touch Sensor Chip" @@ -142,21 +188,34 @@ config KEYBOARD_QT2160 This driver can also be built as a module. If so, the module will be called qt2160. -config KEYBOARD_BFIN - tristate "Blackfin BF54x keypad support" - depends on (BF54x && !BF544) +config KEYBOARD_CLPS711X + tristate "CLPS711X Keypad support" + depends on ARCH_CLPS711X || COMPILE_TEST + select INPUT_MATRIXKMAP + help + Say Y here to enable the matrix keypad on the Cirrus Logic + CLPS711X CPUs. + + To compile this driver as a module, choose M here: the + module will be called clps711x-keypad. + +config KEYBOARD_DLINK_DIR685 + tristate "D-Link DIR-685 touchkeys support" + depends on I2C + default ARCH_GEMINI help - Say Y here if you want to use the BF54x keypad. + If you say yes here you get support for the D-Link DIR-685 + touchkeys. To compile this driver as a module, choose M here: the - module will be called bf54x-keys. + module will be called dlink-dir685-touchkeys. config KEYBOARD_LKKBD tristate "DECstation/VAXstation LK201/LK401 keyboard" select SERIO help Say Y here if you want to use a LK201 or LK401 style serial - keyboard. This keyboard is also useable on PCs if you attach + keyboard. This keyboard is also usable on PCs if you attach it with the inputattach program. The connector pinout is described within lkkbd.c. @@ -165,7 +224,7 @@ config KEYBOARD_LKKBD config KEYBOARD_EP93XX tristate "EP93xx Matrix Keypad support" - depends on ARCH_EP93XX + depends on ARCH_EP93XX || COMPILE_TEST select INPUT_MATRIXKMAP help Say Y here to enable the matrix keypad on the Cirrus EP93XX. @@ -175,7 +234,7 @@ config KEYBOARD_EP93XX config KEYBOARD_GPIO tristate "GPIO Buttons" - depends on GPIOLIB + depends on GPIOLIB || COMPILE_TEST help This driver implements support for buttons connected to GPIO pins of various CPUs (and some other chips). @@ -191,7 +250,6 @@ config KEYBOARD_GPIO config KEYBOARD_GPIO_POLLED tristate "Polled GPIO buttons" depends on GPIOLIB - select INPUT_POLLDEV help This driver implements support for buttons connected to GPIO pins that are not capable of generating interrupts. @@ -204,27 +262,9 @@ config KEYBOARD_GPIO_POLLED To compile this driver as a module, choose M here: the module will be called gpio_keys_polled. -config KEYBOARD_TCA6416 - tristate "TCA6416/TCA6408A Keypad Support" - depends on I2C - help - This driver implements basic keypad functionality - for keys connected through TCA6416/TCA6408A IO expanders. - - Say Y here if your device has keys connected to - TCA6416/TCA6408A IO expander. Your board-specific setup logic - must also provide pin-mask details(of which TCA6416 pins - are used for keypad). - - If enabled the entire TCA6416 device will be managed through - this driver. - - To compile this driver as a module, choose M here: the - module will be called tca6416_keypad. - config KEYBOARD_TCA8418 tristate "TCA8418 Keypad Support" - depends on I2C && GENERIC_HARDIRQS + depends on I2C select INPUT_MATRIXKMAP help This driver implements basic keypad functionality @@ -241,7 +281,7 @@ config KEYBOARD_TCA8418 config KEYBOARD_MATRIX tristate "GPIO driven matrix keypad support" - depends on GPIOLIB + depends on GPIOLIB || COMPILE_TEST select INPUT_MATRIXKMAP help Enable support for GPIO driven matrix keypad. @@ -283,7 +323,6 @@ config KEYBOARD_HIL config KEYBOARD_HP6XX tristate "HP Jornada 6xx keyboard" depends on SH_HP6XX - select INPUT_POLLDEV help Say Y here if you have a HP Jornada 620/660/680/690 and want to support the built-in keyboard. @@ -303,7 +342,7 @@ config KEYBOARD_HP7XX config KEYBOARD_LM8323 tristate "LM8323 keypad chip" - depends on I2C && GENERIC_HARDIRQS + depends on I2C depends on LEDS_CLASS help If you say yes here you get support for the National Semiconductor @@ -334,7 +373,7 @@ config KEYBOARD_LOCOMO config KEYBOARD_LPC32XX tristate "LPC32XX matrix key scanner support" - depends on ARCH_LPC32XX && OF + depends on (ARCH_LPC32XX && OF) || COMPILE_TEST select INPUT_MATRIXKMAP help Say Y here if you want to use NXP LPC32XX SoC key scanner interface, @@ -355,6 +394,7 @@ config KEYBOARD_MAPLE config KEYBOARD_MAX7359 tristate "Maxim MAX7359 Key Switch Controller" + select INPUT_MATRIXKMAP depends on I2C help If you say yes here you get support for the Maxim MAX7359 Key @@ -364,17 +404,17 @@ config KEYBOARD_MAX7359 To compile this driver as a module, choose M here: the module will be called max7359_keypad. -config KEYBOARD_MCS - tristate "MELFAS MCS Touchkey" +config KEYBOARD_MAX7360 + tristate "Maxim MAX7360 Key Switch Controller" + select INPUT_MATRIXKMAP depends on I2C + depends on MFD_MAX7360 help - Say Y here if you have the MELFAS MCS5000/5080 touchkey controller - chip in your system. + If you say yes here you get support for the keypad controller on the + Maxim MAX7360 I/O Expander. - If unsure, say N. - - To compile this driver as a module, choose M here: the - module will be called mcs_touchkey. + To compile this driver as a module, choose M here: the module will be + called max7360_keypad. config KEYBOARD_MPR121 tristate "Freescale MPR121 Touchkey" @@ -388,9 +428,20 @@ config KEYBOARD_MPR121 To compile this driver as a module, choose M here: the module will be called mpr121_touchkey. +config KEYBOARD_SNVS_PWRKEY + tristate "IMX SNVS Power Key Driver" + depends on ARCH_MXC || (COMPILE_TEST && HAS_IOMEM) + depends on OF + help + This is the snvs powerkey driver for the Freescale i.MX application + processors. + + To compile this driver as a module, choose M here; the + module will be called snvs_pwrkey. + config KEYBOARD_IMX tristate "IMX keypad support" - depends on ARCH_MXC + depends on ARCH_MXC || COMPILE_TEST select INPUT_MATRIXKMAP help Enable support for IMX keypad port. @@ -398,6 +449,27 @@ config KEYBOARD_IMX To compile this driver as a module, choose M here: the module will be called imx_keypad. +config KEYBOARD_IMX_BBM_SCMI + tristate "IMX BBM SCMI Key Driver" + depends on IMX_SCMI_BBM_EXT || COMPILE_TEST + default y if ARCH_MXC + help + This is the BBM key driver for NXP i.MX SoCs managed through + SCMI protocol. + + To compile this driver as a module, choose M here: the + module will be called scmi-imx-bbm-key. + +config KEYBOARD_IMX_SC_KEY + tristate "IMX SCU Key Driver" + depends on IMX_SCU + help + This is the system controller key driver for NXP i.MX SoCs with + system controller inside. + + To compile this driver as a module, choose M here: the + module will be called imx_sc_key. + config KEYBOARD_NEWTON tristate "Newton keyboard" select SERIO @@ -407,17 +479,6 @@ config KEYBOARD_NEWTON To compile this driver as a module, choose M here: the module will be called newtonkbd. -config KEYBOARD_NOMADIK - tristate "ST-Ericsson Nomadik SKE keyboard" - depends on (ARCH_NOMADIK || ARCH_U8500) - select INPUT_MATRIXKMAP - help - Say Y here if you want to use a keypad provided on the SKE controller - used on the Ux500 and Nomadik platforms - - To compile this driver as a module, choose M here: the - module will be called nmk-ske-keypad. - config KEYBOARD_NSPIRE tristate "TI-NSPIRE built-in keyboard" depends on ARCH_NSPIRE && OF @@ -430,7 +491,7 @@ config KEYBOARD_NSPIRE config KEYBOARD_TEGRA tristate "NVIDIA Tegra internal matrix keyboard controller support" - depends on ARCH_TEGRA && OF + depends on (ARCH_TEGRA && OF) || COMPILE_TEST select INPUT_MATRIXKMAP help Say Y here if you want to use a matrix keyboard connected directly @@ -449,9 +510,22 @@ config KEYBOARD_OPENCORES To compile this driver as a module, choose M here; the module will be called opencores-kbd. +config KEYBOARD_PINEPHONE + tristate "Pine64 PinePhone Keyboard" + depends on I2C && REGULATOR + select CRC8 + select INPUT_MATRIXKMAP + help + Say Y here to enable support for the keyboard in the Pine64 PinePhone + keyboard case. This driver supports the FLOSS firmware available at + https://megous.com/git/pinephone-keyboard/ + + To compile this driver as a module, choose M here; the + module will be called pinephone-keyboard. + config KEYBOARD_PXA27x tristate "PXA27x/PXA3xx keypad support" - depends on PXA27x || PXA3xx || ARCH_MMP + depends on PXA27x || PXA3xx || ARCH_MMP || COMPILE_TEST select INPUT_MATRIXKMAP help Enable support for PXA27x/PXA3xx keypad controller. @@ -459,15 +533,6 @@ config KEYBOARD_PXA27x To compile this driver as a module, choose M here: the module will be called pxa27x_keypad. -config KEYBOARD_PXA930_ROTARY - tristate "PXA930/PXA935 Enhanced Rotary Controller Support" - depends on CPU_PXA930 || CPU_PXA935 - help - Enable support for PXA930/PXA935 Enhanced Rotary Controller. - - To compile this driver as a module, choose M here: the - module will be called pxa930_rotary. - config KEYBOARD_PMIC8XXX tristate "Qualcomm PMIC8XXX keypad support" depends on MFD_PM8XXX @@ -475,14 +540,14 @@ config KEYBOARD_PMIC8XXX help Say Y here if you want to enable the driver for the PMIC8XXX keypad provided as a reference design from Qualcomm. This is intended - to support upto 18x8 matrix based keypad design. + to support up to 18x8 matrix-based keypad design. To compile this driver as a module, choose M here: the module will be called pmic8xxx-keypad. config KEYBOARD_SAMSUNG tristate "Samsung keypad support" - depends on HAVE_CLK + depends on HAS_IOMEM && HAVE_CLK select INPUT_MATRIXKMAP help Say Y here if you want to use the keypad on your Samsung mobile @@ -492,7 +557,7 @@ config KEYBOARD_SAMSUNG module will be called samsung-keypad. config KEYBOARD_GOLDFISH_EVENTS - depends on GOLDFISH + depends on GOLDFISH || COMPILE_TEST tristate "Generic Input Event device for Goldfish" help Say Y here to get an input event device for the Goldfish virtual @@ -512,6 +577,17 @@ config KEYBOARD_STOWAWAY To compile this driver as a module, choose M here: the module will be called stowaway. +config KEYBOARD_ST_KEYSCAN + tristate "STMicroelectronics keyscan support" + depends on ARCH_STI || COMPILE_TEST + select INPUT_MATRIXKMAP + help + Say Y here if you want to use a keypad attached to the keyscan block + on some STMicroelectronics SoC devices. + + To compile this driver as a module, choose M here: the + module will be called st-keyscan. + config KEYBOARD_SUNKBD tristate "Sun Type 4 and Type 5 keyboard" select SERIO @@ -525,7 +601,7 @@ config KEYBOARD_SUNKBD config KEYBOARD_SH_KEYSC tristate "SuperH KEYSC keypad support" - depends on SUPERH || ARCH_SHMOBILE + depends on ARCH_SHMOBILE || COMPILE_TEST help Say Y here if you want to use a keypad attached to the KEYSC block on SuperH processors such as sh7722 and sh7343. @@ -536,6 +612,7 @@ config KEYBOARD_SH_KEYSC config KEYBOARD_STMPE tristate "STMPE keypad support" depends on MFD_STMPE + depends on OF select INPUT_MATRIXKMAP help Say Y here if you want to use the keypad controller on STMPE I/O @@ -544,15 +621,35 @@ config KEYBOARD_STMPE To compile this driver as a module, choose M here: the module will be called stmpe-keypad. -config KEYBOARD_DAVINCI - tristate "TI DaVinci Key Scan" - depends on ARCH_DAVINCI_DM365 +config KEYBOARD_SUN4I_LRADC + tristate "Allwinner sun4i low res adc attached tablet keys support" + depends on ARCH_SUNXI + help + This selects support for the Allwinner low res adc attached tablet + keys found on Allwinner sunxi SoCs. + + To compile this driver as a module, choose M here: the + module will be called sun4i-lradc-keys. + +config KEYBOARD_IPAQ_MICRO + tristate "Buttons on Micro SoC (iPaq h3100,h3600,h3700)" + depends on MFD_IPAQ_MICRO help - Say Y to enable keypad module support for the TI DaVinci - platforms (DM365). + Say Y to enable support for the buttons attached to + Micro peripheral controller on iPAQ h3100/h3600/h3700 To compile this driver as a module, choose M here: the - module will be called davinci_keyscan. + module will be called ipaq-micro-keys. + +config KEYBOARD_IQS62X + tristate "Azoteq IQS620A/621/622/624/625 keys and switches" + depends on MFD_IQS62X + help + Say Y here to enable key and switch support for the Azoteq IQS620A, + IQS621, IQS622, IQS624 and IQS625 multi-function sensors. + + To compile this driver as a module, choose M here: the module will + be called iqs62x-keys. config KEYBOARD_OMAP tristate "TI OMAP keypad support" @@ -566,7 +663,7 @@ config KEYBOARD_OMAP config KEYBOARD_OMAP4 tristate "TI OMAP4+ keypad support" - depends on ARCH_OMAP2PLUS + depends on (OF && HAS_IOMEM) || ARCH_OMAP2PLUS select INPUT_MATRIXKMAP help Say Y here if you want to use the OMAP4+ keypad. @@ -576,13 +673,13 @@ config KEYBOARD_OMAP4 config KEYBOARD_SPEAR tristate "ST SPEAR keyboard support" - depends on PLAT_SPEAR + depends on PLAT_SPEAR || COMPILE_TEST select INPUT_MATRIXKMAP help Say Y here if you want to use the SPEAR keyboard. To compile this driver as a module, choose M here: the - module will be called spear-keboard. + module will be called spear-keyboard. config KEYBOARD_TC3589X tristate "TC3589X Keypad support" @@ -595,15 +692,16 @@ config KEYBOARD_TC3589X To compile this driver as a module, choose M here: the module will be called tc3589x-keypad. -config KEYBOARD_TNETV107X - tristate "TI TNETV107X keypad support" - depends on ARCH_DAVINCI_TNETV107X - select INPUT_MATRIXKMAP +config KEYBOARD_TM2_TOUCHKEY + tristate "TM2 touchkey support" + depends on I2C + depends on LEDS_CLASS help - Say Y here if you want to use the TNETV107X keypad. + Say Y here to enable device driver for tm2-touchkey with + LED control for the Exynos5433 TM2 board. - To compile this driver as a module, choose M here: the - module will be called tnetv107x-keypad. + To compile this driver as a module, choose M here. + module will be called tm2-touchkey. config KEYBOARD_TWL4030 tristate "TI TWL4030/TWL5030/TPS659x0 keypad support" @@ -629,27 +727,69 @@ config KEYBOARD_XTKBD To compile this driver as a module, choose M here: the module will be called xtkbd. -config KEYBOARD_W90P910 - tristate "W90P910 Matrix Keypad support" - depends on ARCH_W90X900 - select INPUT_MATRIXKMAP - help - Say Y here to enable the matrix keypad on evaluation board - based on W90P910. - - To compile this driver as a module, choose M here: the - module will be called w90p910_keypad. - config KEYBOARD_CROS_EC tristate "ChromeOS EC keyboard" select INPUT_MATRIXKMAP - depends on MFD_CROS_EC + select INPUT_VIVALDIFMAP + depends on CROS_EC help Say Y here to enable the matrix keyboard used by ChromeOS devices and implemented on the ChromeOS EC. You must enable one bus option - (MFD_CROS_EC_I2C or MFD_CROS_EC_SPI) to use this. + (CROS_EC_I2C or CROS_EC_SPI) to use this. To compile this driver as a module, choose M here: the module will be called cros_ec_keyb. +config KEYBOARD_CAP11XX + tristate "Microchip CAP11XX based touch sensors" + depends on OF && I2C + select REGMAP_I2C + help + Say Y here to enable the CAP11XX touch sensor driver. + + To compile this driver as a module, choose M here: the + module will be called cap11xx. + +config KEYBOARD_BCM + tristate "Broadcom keypad driver" + depends on OF && HAVE_CLK && HAS_IOMEM + select INPUT_MATRIXKMAP + default ARCH_BCM_CYGNUS + help + Say Y here if you want to use Broadcom keypad. + + To compile this driver as a module, choose M here: the + module will be called bcm-keypad. + +config KEYBOARD_MT6779 + tristate "MediaTek Keypad Support" + depends on ARCH_MEDIATEK || COMPILE_TEST + select REGMAP_MMIO + select INPUT_MATRIXKMAP + help + Say Y here if you want to use the keypad on MediaTek SoCs. + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called mt6779-keypad. + +config KEYBOARD_MTK_PMIC + tristate "MediaTek PMIC keys support" + depends on MFD_MT6397 || COMPILE_TEST + help + Say Y here if you want to use the pmic keys (powerkey/homekey). + + To compile this driver as a module, choose M here: the + module will be called pmic-keys. + +config KEYBOARD_CYPRESS_SF + tristate "Cypress StreetFighter touchkey support" + depends on I2C + help + Say Y here if you want to enable support for Cypress StreetFighter + touchkeys. + + To compile this driver as a module, choose M here: the + module will be called cypress-sf. + endif |