diff options
Diffstat (limited to 'drivers/net/ethernet/i825xx/ether1.c')
| -rw-r--r-- | drivers/net/ethernet/i825xx/ether1.c | 17 |
1 files changed, 8 insertions, 9 deletions
diff --git a/drivers/net/ethernet/i825xx/ether1.c b/drivers/net/ethernet/i825xx/ether1.c index 35f6291a3672..3e7d7c4bafdc 100644 --- a/drivers/net/ethernet/i825xx/ether1.c +++ b/drivers/net/ethernet/i825xx/ether1.c @@ -1,12 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0-only /* * linux/drivers/acorn/net/ether1.c * * Copyright (C) 1996-2000 Russell King * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - * * Acorn ether1 driver (82586 chip) for Acorn machines * * We basically keep two queues in the cards memory - one for transmit @@ -23,7 +20,7 @@ * 1.02 RMK 25/05/1997 Added code to restart RU if it goes not ready * 1.03 RMK 14/09/1997 Cleaned up the handling of a reset during the TX interrupt. * Should prevent lockup. - * 1.04 RMK 17/09/1997 Added more info when initialsation of chip goes wrong. + * 1.04 RMK 17/09/1997 Added more info when initialisation of chip goes wrong. * TDR now only reports failure when chip reports non-zero * TDR time-distance. * 1.05 RMK 31/12/1997 Removed calls to dev_tint for 2.1 @@ -69,7 +66,7 @@ static netdev_tx_t ether1_sendpacket(struct sk_buff *skb, static irqreturn_t ether1_interrupt(int irq, void *dev_id); static int ether1_close(struct net_device *dev); static void ether1_setmulticastlist(struct net_device *dev); -static void ether1_timeout(struct net_device *dev); +static void ether1_timeout(struct net_device *dev, unsigned int txqueue); /* ------------------------------------------------------------------------- */ @@ -120,7 +117,7 @@ ether1_outw_p (struct net_device *dev, unsigned short val, int addr, int svflgs) * Some inline assembler to allow fast transfers on to/off of the card. * Since this driver depends on some features presented by the ARM * specific architecture, and that you can't configure this driver - * without specifiing ARM mode, this is not a problem. + * without specifying ARM mode, this is not a problem. * * This routine is essentially an optimised memcpy from the card's * onboard RAM to kernel memory. @@ -653,7 +650,7 @@ ether1_open (struct net_device *dev) } static void -ether1_timeout(struct net_device *dev) +ether1_timeout(struct net_device *dev, unsigned int txqueue) { printk(KERN_WARNING "%s: transmit timeout, network cable problem?\n", dev->name); @@ -989,6 +986,7 @@ static int ether1_probe(struct expansion_card *ec, const struct ecard_id *id) { struct net_device *dev; + u8 addr[ETH_ALEN]; int i, ret = 0; ether1_banner(); @@ -1018,7 +1016,8 @@ ether1_probe(struct expansion_card *ec, const struct ecard_id *id) } for (i = 0; i < 6; i++) - dev->dev_addr[i] = readb(IDPROM_ADDRESS + (i << 2)); + addr[i] = readb(IDPROM_ADDRESS + (i << 2)); + eth_hw_addr_set(dev, addr); if (ether1_init_2(dev)) { ret = -ENODEV; |