diff options
Diffstat (limited to 'drivers/net/phy/Kconfig')
| -rw-r--r-- | drivers/net/phy/Kconfig | 565 |
1 files changed, 297 insertions, 268 deletions
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig index 3d187cd50eb0..a7ade7b95a2e 100644 --- a/drivers/net/phy/Kconfig +++ b/drivers/net/phy/Kconfig @@ -1,176 +1,15 @@ +# SPDX-License-Identifier: GPL-2.0-only # # PHY Layer Configuration # -menuconfig MDIO_DEVICE - tristate "MDIO bus device drivers" - help - MDIO devices and driver infrastructure code. - config MDIO_BUS - tristate - default m if PHYLIB=m - default MDIO_DEVICE - help - This internal symbol is used for link time dependencies and it - reflects whether the mdio_bus/mdio_device code is built as a - loadable module or built-in. - -if MDIO_BUS - -config MDIO_BCM_IPROC - tristate "Broadcom iProc MDIO bus controller" - depends on ARCH_BCM_IPROC || COMPILE_TEST - depends on HAS_IOMEM && OF_MDIO - help - This module provides a driver for the MDIO busses found in the - Broadcom iProc SoC's. - -config MDIO_BCM_UNIMAC - tristate "Broadcom UniMAC MDIO bus controller" - depends on HAS_IOMEM - help - This module provides a driver for the Broadcom UniMAC MDIO busses. - This hardware can be found in the Broadcom GENET Ethernet MAC - controllers as well as some Broadcom Ethernet switches such as the - Starfighter 2 switches. - -config MDIO_BITBANG - tristate "Bitbanged MDIO buses" - help - This module implements the MDIO bus protocol in software, - for use by low level drivers that export the ability to - drive the relevant pins. - - If in doubt, say N. - -config MDIO_BUS_MUX - tristate - depends on OF_MDIO - help - This module provides a driver framework for MDIO bus - multiplexers which connect one of several child MDIO busses - to a parent bus. Switching between child busses is done by - device specific drivers. - -config MDIO_BUS_MUX_BCM_IPROC - tristate "Broadcom iProc based MDIO bus multiplexers" - depends on OF && OF_MDIO && (ARCH_BCM_IPROC || COMPILE_TEST) - select MDIO_BUS_MUX - default ARCH_BCM_IPROC - help - This module provides a driver for MDIO bus multiplexers found in - iProc based Broadcom SoCs. This multiplexer connects one of several - child MDIO bus to a parent bus. Buses could be internal as well as - external and selection logic lies inside the same multiplexer. - -config MDIO_BUS_MUX_GPIO - tristate "GPIO controlled MDIO bus multiplexers" - depends on OF_GPIO && OF_MDIO - select MDIO_BUS_MUX - help - This module provides a driver for MDIO bus multiplexers that - are controlled via GPIO lines. The multiplexer connects one of - several child MDIO busses to a parent bus. Child bus - selection is under the control of GPIO lines. - -config MDIO_BUS_MUX_MMIOREG - tristate "MMIO device-controlled MDIO bus multiplexers" - depends on OF_MDIO && HAS_IOMEM - select MDIO_BUS_MUX - help - This module provides a driver for MDIO bus multiplexers that - are controlled via a simple memory-mapped device, like an FPGA. - The multiplexer connects one of several child MDIO busses to a - parent bus. Child bus selection is under the control of one of - the FPGA's registers. - - Currently, only 8/16/32 bits registers are supported. - -config MDIO_CAVIUM - tristate - -config MDIO_GPIO - tristate "GPIO lib-based bitbanged MDIO buses" - depends on MDIO_BITBANG - depends on GPIOLIB || COMPILE_TEST - ---help--- - Supports GPIO lib-based MDIO busses. - - To compile this driver as a module, choose M here: the module - will be called mdio-gpio. - -config MDIO_HISI_FEMAC - tristate "Hisilicon FEMAC MDIO bus controller" - depends on HAS_IOMEM && OF_MDIO - help - This module provides a driver for the MDIO busses found in the - Hisilicon SoC that have an Fast Ethernet MAC. - -config MDIO_I2C - tristate - depends on I2C - help - Support I2C based PHYs. This provides a MDIO bus bridged - to I2C to allow PHYs connected in I2C mode to be accessed - using the existing infrastructure. - - This is library mode. - -config MDIO_MOXART - tristate "MOXA ART MDIO interface support" - depends on ARCH_MOXART || COMPILE_TEST + tristate "MDIO bus consumer layer" help - This driver supports the MDIO interface found in the network - interface units of the MOXA ART SoC - -config MDIO_MSCC_MIIM - tristate "Microsemi MIIM interface support" - depends on HAS_IOMEM - help - This driver supports the MIIM (MDIO) interface found in the network - switches of the Microsemi SoCs - -config MDIO_OCTEON - tristate "Octeon and some ThunderX SOCs MDIO buses" - depends on 64BIT - depends on HAS_IOMEM && OF_MDIO - select MDIO_CAVIUM - help - This module provides a driver for the Octeon and ThunderX MDIO - buses. It is required by the Octeon and ThunderX ethernet device - drivers on some systems. - -config MDIO_SUN4I - tristate "Allwinner sun4i MDIO interface support" - depends on ARCH_SUNXI || COMPILE_TEST - help - This driver supports the MDIO interface found in the network - interface units of the Allwinner SoC that have an EMAC (A10, - A12, A10s, etc.) - -config MDIO_THUNDER - tristate "ThunderX SOCs MDIO buses" - depends on 64BIT - depends on PCI - select MDIO_CAVIUM - help - This driver supports the MDIO interfaces found on Cavium - ThunderX SoCs when the MDIO bus device appears as a PCI - device. - -config MDIO_XGENE - tristate "APM X-Gene SoC MDIO bus controller" - depends on ARCH_XGENE || COMPILE_TEST - help - This module provides a driver for the MDIO busses found in the - APM X-Gene SoC's. - -endif + MDIO bus consumer layer config PHYLINK tristate - depends on NETDEVICES select PHYLIB select SWPHY help @@ -180,8 +19,7 @@ config PHYLINK menuconfig PHYLIB tristate "PHY Device support and infrastructure" - depends on NETDEVICES - select MDIO_DEVICE + select MDIO_BUS help Ethernet controllers are usually attached to PHY devices. This option provides infrastructure for @@ -192,10 +30,13 @@ if PHYLIB config SWPHY bool +config PHY_PACKAGE + tristate + config LED_TRIGGER_PHY bool "Support LED triggers for tracking link state" depends on LEDS_TRIGGERS - ---help--- + help Adds support for a set of LED trigger events per-PHY. Link state change will trigger the events, for consumption by an LED class driver. There are triggers for each link speed currently @@ -208,8 +49,32 @@ config LED_TRIGGER_PHY <Speed in megabits>Mbps OR <Speed in gigabits>Gbps OR link for any speed known to the PHY. +config OPEN_ALLIANCE_HELPERS + bool -comment "MII PHY device drivers" +config PHYLIB_LEDS + def_bool OF + depends on LEDS_CLASS=y || LEDS_CLASS=PHYLIB + help + When LED class support is enabled, phylib can automatically + probe LED setting from device tree. + +config FIXED_PHY + tristate "MDIO Bus/PHY emulation with fixed speed/link PHYs" + select SWPHY + help + Adds the platform "fixed" MDIO Bus to cover the boards that use + PHYs that are not connected to the real MDIO bus. + + Currently tested with mpc866ads and mpc8349e-mitx. + +config RUST_PHYLIB_ABSTRACTIONS + bool "Rust PHYLIB abstractions support" + depends on RUST + depends on PHYLIB=y + help + Adds support needed for PHY drivers written in Rust. It provides + a wrapper around the C phylib core. config SFP tristate "SFP cage support" @@ -217,54 +82,128 @@ config SFP depends on HWMON || HWMON=n select MDIO_I2C +comment "MII PHY device drivers" + +config AS21XXX_PHY + tristate "Aeonsemi AS21xxx PHYs" + help + Currently supports the Aeonsemi AS21xxx PHY. + + These are C45 PHYs 10G that require all a generic firmware. + + Supported PHYs AS21011JB1, AS21011PB1, AS21010JB1, AS21010PB1, + AS21511JB1, AS21511PB1, AS21510JB1, AS21510PB1, AS21210JB1, + AS21210PB1 that all register with the PHY ID 0x7500 0x7500 + before the firmware is loaded. + +config AIR_EN8811H_PHY + tristate "Airoha EN8811H 2.5 Gigabit PHY" + help + Currently supports the Airoha EN8811H PHY. + config AMD_PHY - tristate "AMD PHYs" - ---help--- - Currently supports the am79c874 + tristate "AMD and Altima PHYs" + help + Currently supports the AMD am79c874 and Altima AC101L. -config AQUANTIA_PHY - tristate "Aquantia PHYs" - ---help--- - Currently supports the Aquantia AQ1202, AQ2104, AQR105, AQR405 +config MESON_GXL_PHY + tristate "Amlogic Meson GXL Internal PHY" + depends on ARCH_MESON || COMPILE_TEST + select SMSC_PHY + help + Currently has a driver for the Amlogic Meson GXL Internal PHY + +config ADIN_PHY + tristate "Analog Devices Industrial Ethernet PHYs" + help + Adds support for the Analog Devices Industrial Ethernet PHYs. + Currently supports the: + - ADIN1200 - Robust,Industrial, Low Power 10/100 Ethernet PHY + - ADIN1300 - Robust,Industrial, Low Latency 10/100/1000 Gigabit + Ethernet PHY + +config ADIN1100_PHY + tristate "Analog Devices Industrial Ethernet T1L PHYs" + help + Adds support for the Analog Devices Industrial T1L Ethernet PHYs. + Currently supports the: + - ADIN1100 - Robust,Industrial, Low Power 10BASE-T1L Ethernet PHY + +config AMCC_QT2025_PHY + tristate "AMCC QT2025 PHY" + depends on RUST_PHYLIB_ABSTRACTIONS + depends on RUST_FW_LOADER_ABSTRACTIONS + help + Adds support for the Applied Micro Circuits Corporation QT2025 PHY. + +source "drivers/net/phy/aquantia/Kconfig" -config ASIX_PHY +config AX88796B_PHY tristate "Asix PHYs" help Currently supports the Asix Electronics PHY found in the X-Surf 100 AX88796B package. -config AT803X_PHY - tristate "AT803X PHYs" - ---help--- - Currently supports the AT8030 and AT8035 model +config AX88796B_RUST_PHY + bool "Rust reference driver for Asix PHYs" + depends on RUST_PHYLIB_ABSTRACTIONS && AX88796B_PHY + help + Uses the Rust reference driver for Asix PHYs (ax88796b_rust.ko). + The features are equivalent. It supports the Asix Electronics PHY + found in the X-Surf 100 AX88796B package. + +config BROADCOM_PHY + tristate "Broadcom 54XX PHYs" + select BCM_NET_PHYLIB + select BCM_NET_PHYPTP if NETWORK_PHY_TIMESTAMPING + depends on PTP_1588_CLOCK_OPTIONAL + help + Currently supports the BCM5411, BCM5421, BCM5461, BCM54616S, BCM5464, + BCM5481, BCM54810 and BCM5482 PHYs. + +config BCM54140_PHY + tristate "Broadcom BCM54140 PHY" + depends on HWMON || HWMON=n + select BCM_NET_PHYLIB + select PHY_PACKAGE + help + Support the Broadcom BCM54140 Quad SGMII/QSGMII PHY. + + This driver also supports the hardware monitoring of this PHY and + exposes voltage and temperature sensors. config BCM63XX_PHY tristate "Broadcom 63xx SOCs internal PHY" depends on BCM63XX || COMPILE_TEST select BCM_NET_PHYLIB - ---help--- + help Currently supports the 6348 and 6358 PHYs. config BCM7XXX_PHY tristate "Broadcom 7xxx SOCs internal PHYs" select BCM_NET_PHYLIB - ---help--- + help Currently supports the BCM7366, BCM7439, BCM7445, and 40nm and 65nm generation of BCM7xxx Set Top Box SoCs. +config BCM84881_PHY + tristate "Broadcom BCM84881 PHY" + help + Support the Broadcom BCM84881 PHY. + config BCM87XX_PHY tristate "Broadcom BCM8706 and BCM8727 PHYs" help Currently supports the BCM8706 and BCM8727 10G Ethernet PHYs. config BCM_CYGNUS_PHY - tristate "Broadcom Cygnus SoC internal PHY" - depends on ARCH_BCM_CYGNUS || COMPILE_TEST + tristate "Broadcom Cygnus/Omega SoC internal PHY" + depends on ARCH_BCM_IPROC || COMPILE_TEST depends on MDIO_BCM_IPROC select BCM_NET_PHYLIB - ---help--- + help This PHY driver is for the 1G internal PHYs of the Broadcom - Cygnus Family SoC. + Cygnus and Omega Family SoC. Currently supports internal PHY's used in the BCM11300, BCM11320, BCM11350, BCM11360, BCM58300, BCM58302, @@ -273,66 +212,37 @@ config BCM_CYGNUS_PHY config BCM_NET_PHYLIB tristate -config BROADCOM_PHY - tristate "Broadcom PHYs" - select BCM_NET_PHYLIB - ---help--- - Currently supports the BCM5411, BCM5421, BCM5461, BCM54616S, BCM5464, - BCM5481, BCM54810 and BCM5482 PHYs. +config BCM_NET_PHYPTP + tristate config CICADA_PHY tristate "Cicada PHYs" - ---help--- + help Currently supports the cis8204 config CORTINA_PHY tristate "Cortina EDC CDR 10G Ethernet PHY" - ---help--- + help Currently supports the CS4340 phy. config DAVICOM_PHY tristate "Davicom PHYs" - ---help--- + help Currently supports dm9161e and dm9131 -config DP83822_PHY - tristate "Texas Instruments DP83822 PHY" - ---help--- - Supports the DP83822 PHY. - -config DP83TC811_PHY - tristate "Texas Instruments DP83TC822 PHY" - ---help--- - Supports the DP83TC822 PHY. - -config DP83848_PHY - tristate "Texas Instruments DP83848 PHY" - ---help--- - Supports the DP83848 PHY. - -config DP83867_PHY - tristate "Texas Instruments DP83867 Gigabit PHY" - ---help--- - Currently supports the DP83867 PHY. - -config FIXED_PHY - tristate "MDIO Bus/PHY emulation with fixed speed/link PHYs" - depends on PHYLIB - select SWPHY - ---help--- - Adds the platform "fixed" MDIO Bus to cover the boards that use - PHYs that are not connected to the real MDIO bus. - - Currently tested with mpc866ads and mpc8349e-mitx. - config ICPLUS_PHY tristate "ICPlus PHYs" - ---help--- + help Currently supports the IP175C and IP1001 PHYs. +config LXT_PHY + tristate "Intel LXT PHYs" + help + Currently supports the lxt970, lxt971 + config INTEL_XWAY_PHY tristate "Intel XWAY PHYs" - ---help--- + help Supports the Intel XWAY (former Lantiq) 11G and 22E PHYs. These PHYs are marked as standalone chips under the names PEF 7061, PEF 7071 and PEF 7072 or integrated into the Intel @@ -340,34 +250,66 @@ config INTEL_XWAY_PHY config LSI_ET1011C_PHY tristate "LSI ET1011C PHY" - ---help--- + help Supports the LSI ET1011C PHY. -config LXT_PHY - tristate "Intel LXT PHYs" - ---help--- - Currently supports the lxt970, lxt971 - config MARVELL_PHY - tristate "Marvell PHYs" - ---help--- - Currently has a driver for the 88E1011S + tristate "Marvell Alaska PHYs" + help + Currently has a driver for the 88E1XXX config MARVELL_10G_PHY tristate "Marvell Alaska 10Gbit PHYs" - ---help--- + help Support for the Marvell Alaska MV88X3310 and compatible PHYs. -config MESON_GXL_PHY - tristate "Amlogic Meson GXL Internal PHY" - depends on ARCH_MESON || COMPILE_TEST - ---help--- - Currently has a driver for the Amlogic Meson GXL Internal PHY +config MARVELL_88Q2XXX_PHY + tristate "Marvell 88Q2XXX PHY" + depends on HWMON || HWMON=n + help + Support for the Marvell 88Q2XXX 100/1000BASE-T1 Automotive Ethernet + PHYs. + +config MARVELL_88X2222_PHY + tristate "Marvell 88X2222 PHY" + help + Support for the Marvell 88X2222 Dual-port Multi-speed Ethernet + Transceiver. + +config MAXLINEAR_GPHY + tristate "Maxlinear Ethernet PHYs" + select POLYNOMIAL if HWMON + depends on HWMON || HWMON=n + help + Support for the Maxlinear GPY115, GPY211, GPY212, GPY215, + GPY241, GPY245 PHYs. + +config MAXLINEAR_86110_PHY + tristate "MaxLinear MXL86110 PHY support" + help + Support for the MaxLinear MXL86110 Gigabit Ethernet + Physical Layer transceiver. + The MXL86110 is commonly used in networking equipment such as + routers, switches, and embedded systems, providing the + physical interface for 10/100/1000 Mbps Ethernet connections + over copper media. + If you are using a board with the MXL86110 PHY connected to your + Ethernet MAC, you should enable this option. + +source "drivers/net/phy/mediatek/Kconfig" config MICREL_PHY tristate "Micrel PHYs" - ---help--- - Supports the KSZ9021, VSC8201, KS8001 PHYs. + depends on PTP_1588_CLOCK_OPTIONAL + select PHY_PACKAGE + help + Supports the KSZ8xxx, KSZ9xxx, and LAN88xx families of Micrel/Microchip PHYs. + +config MICROCHIP_T1S_PHY + tristate "Microchip 10BASE-T1S Ethernet PHYs" + help + Currently supports the LAN8670/1/2 Rev.B1/C1/C2/D0 and + LAN8650/1 Rev.B0/B1 Internal PHYs. config MICROCHIP_PHY tristate "Microchip PHYs" @@ -376,68 +318,155 @@ config MICROCHIP_PHY config MICROCHIP_T1_PHY tristate "Microchip T1 PHYs" - ---help--- - Supports the LAN87XX PHYs. + select MICROCHIP_PHY_RDS_PTP if NETWORK_PHY_TIMESTAMPING + depends on PTP_1588_CLOCK_OPTIONAL + help + Supports the LAN8XXX PHYs. + +config MICROCHIP_PHY_RDS_PTP + tristate + help + Currently supports LAN887X T1 PHY config MICROSEMI_PHY tristate "Microsemi PHYs" - ---help--- - Currently supports VSC8530, VSC8531, VSC8540 and VSC8541 PHYs + depends on MACSEC || MACSEC=n + depends on PTP_1588_CLOCK_OPTIONAL || !NETWORK_PHY_TIMESTAMPING + select CRYPTO_LIB_AES if MACSEC + select PHY_PACKAGE + help + Currently supports VSC8514, VSC8530, VSC8531, VSC8540 and VSC8541 PHYs + +config MOTORCOMM_PHY + tristate "Motorcomm PHYs" + help + Enables support for Motorcomm network PHYs. + Currently supports YT85xx Gigabit Ethernet PHYs. config NATIONAL_PHY tristate "National Semiconductor PHYs" - ---help--- + help Currently supports the DP83865 PHY. +config NXP_CBTX_PHY + tristate "NXP 100BASE-TX PHYs" + help + Support the 100BASE-TX PHY integrated on the SJA1110 automotive + switch family. + +config NXP_C45_TJA11XX_PHY + tristate "NXP C45 TJA11XX PHYs" + depends on PTP_1588_CLOCK_OPTIONAL + depends on MACSEC || !MACSEC + help + Enable support for NXP C45 TJA11XX PHYs. + Currently supports the TJA1103, TJA1104, TJA1120 and TJA1121 PHYs. + +config NXP_TJA11XX_PHY + tristate "NXP TJA11xx PHYs support" + depends on HWMON + help + Currently supports the NXP TJA1100, TJA1101 and TJA1102 PHYs. + +config NCN26000_PHY + tristate "Onsemi 10BASE-T1S Ethernet PHY" + help + Adds support for the onsemi 10BASE-T1S Ethernet PHY. + Currently supports the NCN26000 10BASE-T1S Industrial PHY + with MII interface. + +source "drivers/net/phy/qcom/Kconfig" + config QSEMI_PHY tristate "Quality Semiconductor PHYs" - ---help--- + help Currently supports the qs6612 -config REALTEK_PHY - tristate "Realtek PHYs" - ---help--- - Supports the Realtek 821x PHY. +source "drivers/net/phy/realtek/Kconfig" config RENESAS_PHY - tristate "Driver for Renesas PHYs" - ---help--- + tristate "Renesas PHYs" + help Supports the Renesas PHYs uPD60620 and uPD60620A. config ROCKCHIP_PHY - tristate "Driver for Rockchip Ethernet PHYs" - ---help--- - Currently supports the integrated Ethernet PHY. + tristate "Rockchip Ethernet PHYs" + help + Currently supports the integrated Ethernet PHY. config SMSC_PHY tristate "SMSC PHYs" - ---help--- + select CRC16 + help Currently supports the LAN83C185, LAN8187 and LAN8700 PHYs config STE10XP tristate "STMicroelectronics STe10Xp PHYs" - ---help--- + help This is the driver for the STe100p and STe101p PHYs. config TERANETICS_PHY tristate "Teranetics PHYs" - ---help--- + help Currently supports the Teranetics TN2020 +config DP83822_PHY + tristate "Texas Instruments DP83822/825/826 PHYs" + help + Supports the DP83822, DP83825I, DP83825CM, DP83825CS, DP83825S, + DP83826C and DP83826NC PHYs. + +config DP83TC811_PHY + tristate "Texas Instruments DP83TC811 PHY" + help + Supports the DP83TC811 PHY. + +config DP83848_PHY + tristate "Texas Instruments DP83848 PHY" + help + Supports the DP83848 PHY. + +config DP83867_PHY + tristate "Texas Instruments DP83867 Gigabit PHY" + help + Currently supports the DP83867 PHY. + +config DP83869_PHY + tristate "Texas Instruments DP83869 Gigabit PHY" + help + Currently supports the DP83869 PHY. This PHY supports copper and + fiber connections. + +config DP83TD510_PHY + tristate "Texas Instruments DP83TD510 Ethernet 10Base-T1L PHY" + help + Support for the DP83TD510 Ethernet 10Base-T1L PHY. This PHY supports + a 10M single pair Ethernet connection for up to 1000 meter cable. + +config DP83TG720_PHY + tristate "Texas Instruments DP83TG720 Ethernet 1000Base-T1 PHY" + select OPEN_ALLIANCE_HELPERS + help + The DP83TG720S-Q1 is an automotive Ethernet physical layer + transceiver compliant with IEEE 802.3bp and Open Alliance + standards. It supports key functions necessary for + transmitting and receiving data over both unshielded and + shielded single twisted-pair cables. This device offers + flexible xMII interface options, including support for both + RGMII and SGMII MAC interfaces. It's suitable for applications + requiring high-speed data transmission in automotive + networking environments. + config VITESSE_PHY tristate "Vitesse PHYs" - ---help--- + help Currently supports the vsc8244 config XILINX_GMII2RGMII tristate "Xilinx GMII2RGMII converter driver" - ---help--- + help This driver support xilinx GMII to RGMII IP core it provides the Reduced Gigabit Media Independent Interface(RGMII) between Ethernet physical media devices and the Gigabit Ethernet controller. endif # PHYLIB - -config MICREL_KS8995MA - tristate "Micrel KS8995MA 5-ports 10/100 managed Ethernet switch" - depends on SPI |