summaryrefslogtreecommitdiff
path: root/drivers/net/phy/at803x.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/phy/at803x.c')
-rw-r--r--drivers/net/phy/at803x.c312
1 files changed, 301 insertions, 11 deletions
diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c
index 1eb5d4fb8925..aee62610bade 100644
--- a/drivers/net/phy/at803x.c
+++ b/drivers/net/phy/at803x.c
@@ -2,7 +2,7 @@
/*
* drivers/net/phy/at803x.c
*
- * Driver for Atheros 803x PHY
+ * Driver for Qualcomm Atheros AR803x PHY
*
* Author: Matus Ujhelyi <ujhelyi.m@gmail.com>
*/
@@ -13,7 +13,12 @@
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/of_gpio.h>
+#include <linux/bitfield.h>
#include <linux/gpio/consumer.h>
+#include <linux/regulator/of_regulator.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/consumer.h>
+#include <dt-bindings/net/qca-ar803x.h>
#define AT803X_SPECIFIC_STATUS 0x11
#define AT803X_SS_SPEED_MASK (3 << 14)
@@ -62,17 +67,60 @@
#define AT803X_DEBUG_REG_5 0x05
#define AT803X_DEBUG_TX_CLK_DLY_EN BIT(8)
+#define AT803X_DEBUG_REG_1F 0x1F
+#define AT803X_DEBUG_PLL_ON BIT(2)
+#define AT803X_DEBUG_RGMII_1V8 BIT(3)
+
+/* AT803x supports either the XTAL input pad, an internal PLL or the
+ * DSP as clock reference for the clock output pad. The XTAL reference
+ * is only used for 25 MHz output, all other frequencies need the PLL.
+ * The DSP as a clock reference is used in synchronous ethernet
+ * applications.
+ *
+ * By default the PLL is only enabled if there is a link. Otherwise
+ * the PHY will go into low power state and disabled the PLL. You can
+ * set the PLL_ON bit (see debug register 0x1f) to keep the PLL always
+ * enabled.
+ */
+#define AT803X_MMD7_CLK25M 0x8016
+#define AT803X_CLK_OUT_MASK GENMASK(4, 2)
+#define AT803X_CLK_OUT_25MHZ_XTAL 0
+#define AT803X_CLK_OUT_25MHZ_DSP 1
+#define AT803X_CLK_OUT_50MHZ_PLL 2
+#define AT803X_CLK_OUT_50MHZ_DSP 3
+#define AT803X_CLK_OUT_62_5MHZ_PLL 4
+#define AT803X_CLK_OUT_62_5MHZ_DSP 5
+#define AT803X_CLK_OUT_125MHZ_PLL 6
+#define AT803X_CLK_OUT_125MHZ_DSP 7
+
+/* The AR8035 has another mask which is compatible with the AR8031/AR8033 mask
+ * but doesn't support choosing between XTAL/PLL and DSP.
+ */
+#define AT8035_CLK_OUT_MASK GENMASK(4, 3)
+
+#define AT803X_CLK_OUT_STRENGTH_MASK GENMASK(8, 7)
+#define AT803X_CLK_OUT_STRENGTH_FULL 0
+#define AT803X_CLK_OUT_STRENGTH_HALF 1
+#define AT803X_CLK_OUT_STRENGTH_QUARTER 2
+
+#define ATH9331_PHY_ID 0x004dd041
#define ATH8030_PHY_ID 0x004dd076
#define ATH8031_PHY_ID 0x004dd074
#define ATH8035_PHY_ID 0x004dd072
#define AT803X_PHY_ID_MASK 0xffffffef
-MODULE_DESCRIPTION("Atheros 803x PHY driver");
+MODULE_DESCRIPTION("Qualcomm Atheros AR803x PHY driver");
MODULE_AUTHOR("Matus Ujhelyi");
MODULE_LICENSE("GPL");
struct at803x_priv {
- bool phy_reset:1;
+ int flags;
+#define AT803X_KEEP_PLL_ENABLED BIT(0) /* don't turn off internal PLL */
+ u16 clk_25m_reg;
+ u16 clk_25m_mask;
+ struct regulator_dev *vddio_rdev;
+ struct regulator_dev *vddh_rdev;
+ struct regulator *vddio;
};
struct at803x_context {
@@ -240,6 +288,193 @@ static int at803x_resume(struct phy_device *phydev)
return phy_modify(phydev, MII_BMCR, BMCR_PDOWN | BMCR_ISOLATE, 0);
}
+static int at803x_rgmii_reg_set_voltage_sel(struct regulator_dev *rdev,
+ unsigned int selector)
+{
+ struct phy_device *phydev = rdev_get_drvdata(rdev);
+
+ if (selector)
+ return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F,
+ 0, AT803X_DEBUG_RGMII_1V8);
+ else
+ return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F,
+ AT803X_DEBUG_RGMII_1V8, 0);
+}
+
+static int at803x_rgmii_reg_get_voltage_sel(struct regulator_dev *rdev)
+{
+ struct phy_device *phydev = rdev_get_drvdata(rdev);
+ int val;
+
+ val = at803x_debug_reg_read(phydev, AT803X_DEBUG_REG_1F);
+ if (val < 0)
+ return val;
+
+ return (val & AT803X_DEBUG_RGMII_1V8) ? 1 : 0;
+}
+
+static struct regulator_ops vddio_regulator_ops = {
+ .list_voltage = regulator_list_voltage_table,
+ .set_voltage_sel = at803x_rgmii_reg_set_voltage_sel,
+ .get_voltage_sel = at803x_rgmii_reg_get_voltage_sel,
+};
+
+static const unsigned int vddio_voltage_table[] = {
+ 1500000,
+ 1800000,
+};
+
+static const struct regulator_desc vddio_desc = {
+ .name = "vddio",
+ .of_match = of_match_ptr("vddio-regulator"),
+ .n_voltages = ARRAY_SIZE(vddio_voltage_table),
+ .volt_table = vddio_voltage_table,
+ .ops = &vddio_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+};
+
+static struct regulator_ops vddh_regulator_ops = {
+};
+
+static const struct regulator_desc vddh_desc = {
+ .name = "vddh",
+ .of_match = of_match_ptr("vddh-regulator"),
+ .n_voltages = 1,
+ .fixed_uV = 2500000,
+ .ops = &vddh_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+};
+
+static int at8031_register_regulators(struct phy_device *phydev)
+{
+ struct at803x_priv *priv = phydev->priv;
+ struct device *dev = &phydev->mdio.dev;
+ struct regulator_config config = { };
+
+ config.dev = dev;
+ config.driver_data = phydev;
+
+ priv->vddio_rdev = devm_regulator_register(dev, &vddio_desc, &config);
+ if (IS_ERR(priv->vddio_rdev)) {
+ phydev_err(phydev, "failed to register VDDIO regulator\n");
+ return PTR_ERR(priv->vddio_rdev);
+ }
+
+ priv->vddh_rdev = devm_regulator_register(dev, &vddh_desc, &config);
+ if (IS_ERR(priv->vddh_rdev)) {
+ phydev_err(phydev, "failed to register VDDH regulator\n");
+ return PTR_ERR(priv->vddh_rdev);
+ }
+
+ return 0;
+}
+
+static bool at803x_match_phy_id(struct phy_device *phydev, u32 phy_id)
+{
+ return (phydev->phy_id & phydev->drv->phy_id_mask)
+ == (phy_id & phydev->drv->phy_id_mask);
+}
+
+static int at803x_parse_dt(struct phy_device *phydev)
+{
+ struct device_node *node = phydev->mdio.dev.of_node;
+ struct at803x_priv *priv = phydev->priv;
+ unsigned int sel, mask;
+ u32 freq, strength;
+ int ret;
+
+ if (!IS_ENABLED(CONFIG_OF_MDIO))
+ return 0;
+
+ ret = of_property_read_u32(node, "qca,clk-out-frequency", &freq);
+ if (!ret) {
+ mask = AT803X_CLK_OUT_MASK;
+ switch (freq) {
+ case 25000000:
+ sel = AT803X_CLK_OUT_25MHZ_XTAL;
+ break;
+ case 50000000:
+ sel = AT803X_CLK_OUT_50MHZ_PLL;
+ break;
+ case 62500000:
+ sel = AT803X_CLK_OUT_62_5MHZ_PLL;
+ break;
+ case 125000000:
+ sel = AT803X_CLK_OUT_125MHZ_PLL;
+ break;
+ default:
+ phydev_err(phydev, "invalid qca,clk-out-frequency\n");
+ return -EINVAL;
+ }
+
+ priv->clk_25m_reg |= FIELD_PREP(mask, sel);
+ priv->clk_25m_mask |= mask;
+
+ /* Fixup for the AR8030/AR8035. This chip has another mask and
+ * doesn't support the DSP reference. Eg. the lowest bit of the
+ * mask. The upper two bits select the same frequencies. Mask
+ * the lowest bit here.
+ *
+ * Warning:
+ * There was no datasheet for the AR8030 available so this is
+ * just a guess. But the AR8035 is listed as pin compatible
+ * to the AR8030 so there might be a good chance it works on
+ * the AR8030 too.
+ */
+ if (at803x_match_phy_id(phydev, ATH8030_PHY_ID) ||
+ at803x_match_phy_id(phydev, ATH8035_PHY_ID)) {
+ priv->clk_25m_reg &= ~AT8035_CLK_OUT_MASK;
+ priv->clk_25m_mask &= ~AT8035_CLK_OUT_MASK;
+ }
+ }
+
+ ret = of_property_read_u32(node, "qca,clk-out-strength", &strength);
+ if (!ret) {
+ priv->clk_25m_mask |= AT803X_CLK_OUT_STRENGTH_MASK;
+ switch (strength) {
+ case AR803X_STRENGTH_FULL:
+ priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_FULL;
+ break;
+ case AR803X_STRENGTH_HALF:
+ priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_HALF;
+ break;
+ case AR803X_STRENGTH_QUARTER:
+ priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_QUARTER;
+ break;
+ default:
+ phydev_err(phydev, "invalid qca,clk-out-strength\n");
+ return -EINVAL;
+ }
+ }
+
+ /* Only supported on AR8031/AR8033, the AR8030/AR8035 use strapping
+ * options.
+ */
+ if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) {
+ if (of_property_read_bool(node, "qca,keep-pll-enabled"))
+ priv->flags |= AT803X_KEEP_PLL_ENABLED;
+
+ ret = at8031_register_regulators(phydev);
+ if (ret < 0)
+ return ret;
+
+ priv->vddio = devm_regulator_get_optional(&phydev->mdio.dev,
+ "vddio");
+ if (IS_ERR(priv->vddio)) {
+ phydev_err(phydev, "failed to get VDDIO regulator\n");
+ return PTR_ERR(priv->vddio);
+ }
+
+ ret = regulator_enable(priv->vddio);
+ if (ret < 0)
+ return ret;
+ }
+
+ return 0;
+}
+
static int at803x_probe(struct phy_device *phydev)
{
struct device *dev = &phydev->mdio.dev;
@@ -251,7 +486,40 @@ static int at803x_probe(struct phy_device *phydev)
phydev->priv = priv;
- return 0;
+ return at803x_parse_dt(phydev);
+}
+
+static int at803x_clk_out_config(struct phy_device *phydev)
+{
+ struct at803x_priv *priv = phydev->priv;
+ int val;
+
+ if (!priv->clk_25m_mask)
+ return 0;
+
+ val = phy_read_mmd(phydev, MDIO_MMD_AN, AT803X_MMD7_CLK25M);
+ if (val < 0)
+ return val;
+
+ val &= ~priv->clk_25m_mask;
+ val |= priv->clk_25m_reg;
+
+ return phy_write_mmd(phydev, MDIO_MMD_AN, AT803X_MMD7_CLK25M, val);
+}
+
+static int at8031_pll_config(struct phy_device *phydev)
+{
+ struct at803x_priv *priv = phydev->priv;
+
+ /* The default after hardware reset is PLL OFF. After a soft reset, the
+ * values are retained.
+ */
+ if (priv->flags & AT803X_KEEP_PLL_ENABLED)
+ return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F,
+ 0, AT803X_DEBUG_PLL_ON);
+ else
+ return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F,
+ AT803X_DEBUG_PLL_ON, 0);
}
static int at803x_config_init(struct phy_device *phydev)
@@ -276,8 +544,20 @@ static int at803x_config_init(struct phy_device *phydev)
ret = at803x_enable_tx_delay(phydev);
else
ret = at803x_disable_tx_delay(phydev);
+ if (ret < 0)
+ return ret;
- return ret;
+ ret = at803x_clk_out_config(phydev);
+ if (ret < 0)
+ return ret;
+
+ if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) {
+ ret = at8031_pll_config(phydev);
+ if (ret < 0)
+ return ret;
+ }
+
+ return 0;
}
static int at803x_ack_interrupt(struct phy_device *phydev)
@@ -426,9 +706,9 @@ static int at803x_read_status(struct phy_device *phydev)
static struct phy_driver at803x_driver[] = {
{
- /* ATHEROS 8035 */
+ /* Qualcomm Atheros AR8035 */
.phy_id = ATH8035_PHY_ID,
- .name = "Atheros 8035 ethernet",
+ .name = "Qualcomm Atheros AR8035",
.phy_id_mask = AT803X_PHY_ID_MASK,
.probe = at803x_probe,
.config_init = at803x_config_init,
@@ -441,9 +721,9 @@ static struct phy_driver at803x_driver[] = {
.ack_interrupt = at803x_ack_interrupt,
.config_intr = at803x_config_intr,
}, {
- /* ATHEROS 8030 */
+ /* Qualcomm Atheros AR8030 */
.phy_id = ATH8030_PHY_ID,
- .name = "Atheros 8030 ethernet",
+ .name = "Qualcomm Atheros AR8030",
.phy_id_mask = AT803X_PHY_ID_MASK,
.probe = at803x_probe,
.config_init = at803x_config_init,
@@ -456,9 +736,9 @@ static struct phy_driver at803x_driver[] = {
.ack_interrupt = at803x_ack_interrupt,
.config_intr = at803x_config_intr,
}, {
- /* ATHEROS 8031 */
+ /* Qualcomm Atheros AR8031/AR8033 */
.phy_id = ATH8031_PHY_ID,
- .name = "Atheros 8031 ethernet",
+ .name = "Qualcomm Atheros AR8031/AR8033",
.phy_id_mask = AT803X_PHY_ID_MASK,
.probe = at803x_probe,
.config_init = at803x_config_init,
@@ -471,6 +751,15 @@ static struct phy_driver at803x_driver[] = {
.aneg_done = at803x_aneg_done,
.ack_interrupt = &at803x_ack_interrupt,
.config_intr = &at803x_config_intr,
+}, {
+ /* ATHEROS AR9331 */
+ PHY_ID_MATCH_EXACT(ATH9331_PHY_ID),
+ .name = "Qualcomm Atheros AR9331 built-in PHY",
+ .suspend = at803x_suspend,
+ .resume = at803x_resume,
+ /* PHY_BASIC_FEATURES */
+ .ack_interrupt = &at803x_ack_interrupt,
+ .config_intr = &at803x_config_intr,
} };
module_phy_driver(at803x_driver);
@@ -479,6 +768,7 @@ static struct mdio_device_id __maybe_unused atheros_tbl[] = {
{ ATH8030_PHY_ID, AT803X_PHY_ID_MASK },
{ ATH8031_PHY_ID, AT803X_PHY_ID_MASK },
{ ATH8035_PHY_ID, AT803X_PHY_ID_MASK },
+ { PHY_ID_MATCH_EXACT(ATH9331_PHY_ID) },
{ }
};