diff options
Diffstat (limited to 'drivers/net/phy/micrel.c')
| -rw-r--r-- | drivers/net/phy/micrel.c | 3940 |
1 files changed, 3646 insertions, 294 deletions
diff --git a/drivers/net/phy/micrel.c b/drivers/net/phy/micrel.c index 26ce0c5defcd..05de68b9f719 100644 --- a/drivers/net/phy/micrel.c +++ b/drivers/net/phy/micrel.c @@ -10,13 +10,13 @@ * Copyright (c) 2014 Johan Hovold <johan@kernel.org> * * Support : Micrel Phys: - * Giga phys: ksz9021, ksz9031, ksz9131 + * Giga phys: ksz9021, ksz9031, ksz9131, lan8841, lan8814 * 100/10 Phys : ksz8001, ksz8721, ksz8737, ksz8041 * ksz8021, ksz8031, ksz8051, * ksz8081, ksz8091, * ksz8061, * Switch : ksz8873, ksz886x - * ksz9477 + * ksz9477, lan8804 */ #include <linux/bitfield.h> @@ -34,6 +34,8 @@ #include <linux/net_tstamp.h> #include <linux/gpio/consumer.h> +#include "phylib.h" + /* Operation Mode Strap Override */ #define MII_KSZPHY_OMSO 0x16 #define KSZPHY_OMSO_FACTORY_TEST BIT(15) @@ -99,12 +101,15 @@ #define LAN8814_CABLE_DIAG_VCT_DATA_MASK GENMASK(7, 0) #define LAN8814_PAIR_BIT_SHIFT 12 +#define LAN8814_SKUS 0xB + #define LAN8814_WIRE_PAIR_MASK 0xF /* Lan8814 general Interrupt control/status reg in GPHY specific block. */ #define LAN8814_INTC 0x18 #define LAN8814_INTS 0x1B +#define LAN8814_INT_FLF BIT(15) #define LAN8814_INT_LINK_DOWN BIT(2) #define LAN8814_INT_LINK_UP BIT(0) #define LAN8814_INT_LINK (LAN8814_INT_LINK_UP |\ @@ -114,12 +119,30 @@ #define LAN8814_INTR_CTRL_REG_POLARITY BIT(1) #define LAN8814_INTR_CTRL_REG_INTR_ENABLE BIT(0) +#define LAN8814_EEE_STATE 0x38 +#define LAN8814_EEE_STATE_MASK2P5P BIT(10) + +#define LAN8814_PD_CONTROLS 0x9d +#define LAN8814_PD_CONTROLS_PD_MEAS_TIME_MASK GENMASK(3, 0) +#define LAN8814_PD_CONTROLS_PD_MEAS_TIME_VAL 0xb + /* Represents 1ppm adjustment in 2^32 format with * each nsec contains 4 clock cycles. * The value is calculated as following: (1/1000000)/((2^-32)/4) */ #define LAN8814_1PPM_FORMAT 17179 +/* Represents 1ppm adjustment in 2^32 format with + * each nsec contains 8 clock cycles. + * The value is calculated as following: (1/1000000)/((2^-32)/8) + */ +#define LAN8841_1PPM_FORMAT 34360 + +#define PTP_RX_VERSION 0x0248 +#define PTP_TX_VERSION 0x0288 +#define PTP_MAX_VERSION(x) (((x) & GENMASK(7, 0)) << 8) +#define PTP_MIN_VERSION(x) ((x) & GENMASK(7, 0)) + #define PTP_RX_MOD 0x024F #define PTP_RX_MOD_BAD_UDPV4_CHKSUM_FORCE_FCS_DIS_ BIT(3) #define PTP_RX_TIMESTAMP_EN 0x024D @@ -149,16 +172,42 @@ #define PTP_CMD_CTL_PTP_LTC_STEP_SEC_ BIT(5) #define PTP_CMD_CTL_PTP_LTC_STEP_NSEC_ BIT(6) +#define PTP_COMMON_INT_ENA 0x0204 +#define PTP_COMMON_INT_ENA_GPIO_CAP_EN BIT(2) + +#define PTP_CLOCK_SET_SEC_HI 0x0205 #define PTP_CLOCK_SET_SEC_MID 0x0206 #define PTP_CLOCK_SET_SEC_LO 0x0207 #define PTP_CLOCK_SET_NS_HI 0x0208 #define PTP_CLOCK_SET_NS_LO 0x0209 +#define PTP_CLOCK_READ_SEC_HI 0x0229 #define PTP_CLOCK_READ_SEC_MID 0x022A #define PTP_CLOCK_READ_SEC_LO 0x022B #define PTP_CLOCK_READ_NS_HI 0x022C #define PTP_CLOCK_READ_NS_LO 0x022D +#define PTP_GPIO_SEL 0x0230 +#define PTP_GPIO_SEL_GPIO_SEL(pin) ((pin) << 8) +#define PTP_GPIO_CAP_MAP_LO 0x0232 + +#define PTP_GPIO_CAP_EN 0x0233 +#define PTP_GPIO_CAP_EN_GPIO_RE_CAPTURE_ENABLE(gpio) BIT(gpio) +#define PTP_GPIO_CAP_EN_GPIO_FE_CAPTURE_ENABLE(gpio) (BIT(gpio) << 8) + +#define PTP_GPIO_RE_LTC_SEC_HI_CAP 0x0235 +#define PTP_GPIO_RE_LTC_SEC_LO_CAP 0x0236 +#define PTP_GPIO_RE_LTC_NS_HI_CAP 0x0237 +#define PTP_GPIO_RE_LTC_NS_LO_CAP 0x0238 +#define PTP_GPIO_FE_LTC_SEC_HI_CAP 0x0239 +#define PTP_GPIO_FE_LTC_SEC_LO_CAP 0x023A +#define PTP_GPIO_FE_LTC_NS_HI_CAP 0x023B +#define PTP_GPIO_FE_LTC_NS_LO_CAP 0x023C + +#define PTP_GPIO_CAP_STS 0x023D +#define PTP_GPIO_CAP_STS_PTP_GPIO_RE_STS(gpio) BIT(gpio) +#define PTP_GPIO_CAP_STS_PTP_GPIO_FE_STS(gpio) (BIT(gpio) << 8) + #define PTP_OPERATING_MODE 0x0241 #define PTP_OPERATING_MODE_STANDALONE_ BIT(0) @@ -220,6 +269,8 @@ #define LAN8814_LED_CTRL_1 0x0 #define LAN8814_LED_CTRL_1_KSZ9031_LED_MODE_ BIT(6) +#define LAN8814_LED_CTRL_2 0x1 +#define LAN8814_LED_CTRL_2_LED1_COM_DIS BIT(8) /* PHY Control 1 */ #define MII_KSZPHY_CTRL_1 0x1e @@ -252,6 +303,75 @@ #define PS_TO_REG 200 #define FIFO_SIZE 8 +#define LAN8814_PTP_GPIO_NUM 24 +#define LAN8814_PTP_PEROUT_NUM 2 +#define LAN8814_PTP_EXTTS_NUM 3 + +#define LAN8814_BUFFER_TIME 2 + +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_200MS 13 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_100MS 12 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_50MS 11 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_10MS 10 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_5MS 9 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_1MS 8 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_500US 7 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_100US 6 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_50US 5 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_10US 4 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_5US 3 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_1US 2 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_500NS 1 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_100NS 0 + +#define LAN8814_GPIO_EN1 0x20 +#define LAN8814_GPIO_EN2 0x21 +#define LAN8814_GPIO_DIR1 0x22 +#define LAN8814_GPIO_DIR2 0x23 +#define LAN8814_GPIO_BUF1 0x24 +#define LAN8814_GPIO_BUF2 0x25 + +#define LAN8814_GPIO_EN_ADDR(pin) \ + ((pin) > 15 ? LAN8814_GPIO_EN1 : LAN8814_GPIO_EN2) +#define LAN8814_GPIO_EN_BIT(pin) BIT(pin) +#define LAN8814_GPIO_DIR_ADDR(pin) \ + ((pin) > 15 ? LAN8814_GPIO_DIR1 : LAN8814_GPIO_DIR2) +#define LAN8814_GPIO_DIR_BIT(pin) BIT(pin) +#define LAN8814_GPIO_BUF_ADDR(pin) \ + ((pin) > 15 ? LAN8814_GPIO_BUF1 : LAN8814_GPIO_BUF2) +#define LAN8814_GPIO_BUF_BIT(pin) BIT(pin) + +#define LAN8814_EVENT_A 0 +#define LAN8814_EVENT_B 1 + +#define LAN8814_PTP_GENERAL_CONFIG 0x0201 +#define LAN8814_PTP_GENERAL_CONFIG_LTC_EVENT_MASK(event) \ + ((event) ? GENMASK(11, 8) : GENMASK(7, 4)) +#define LAN8814_PTP_GENERAL_CONFIG_LTC_EVENT_SET(event, value) \ + (((value) & GENMASK(3, 0)) << (4 + ((event) << 2))) +#define LAN8814_PTP_GENERAL_CONFIG_RELOAD_ADD_X(event) \ + ((event) ? BIT(2) : BIT(0)) +#define LAN8814_PTP_GENERAL_CONFIG_POLARITY_X(event) \ + ((event) ? BIT(3) : BIT(1)) + +#define LAN8814_PTP_CLOCK_TARGET_SEC_HI(event) ((event) ? 0x21F : 0x215) +#define LAN8814_PTP_CLOCK_TARGET_SEC_LO(event) ((event) ? 0x220 : 0x216) +#define LAN8814_PTP_CLOCK_TARGET_NS_HI(event) ((event) ? 0x221 : 0x217) +#define LAN8814_PTP_CLOCK_TARGET_NS_LO(event) ((event) ? 0x222 : 0x218) + +#define LAN8814_PTP_CLOCK_TARGET_RELOAD_SEC_HI(event) ((event) ? 0x223 : 0x219) +#define LAN8814_PTP_CLOCK_TARGET_RELOAD_SEC_LO(event) ((event) ? 0x224 : 0x21A) +#define LAN8814_PTP_CLOCK_TARGET_RELOAD_NS_HI(event) ((event) ? 0x225 : 0x21B) +#define LAN8814_PTP_CLOCK_TARGET_RELOAD_NS_LO(event) ((event) ? 0x226 : 0x21C) + +/* Delay used to get the second part from the LTC */ +#define LAN8841_GET_SEC_LTC_DELAY (500 * NSEC_PER_MSEC) + +#define LAN8842_REV_8832 0x8832 + +#define LAN8814_REV_LAN8814 0x8814 +#define LAN8814_REV_LAN8818 0x8818 + struct kszphy_hw_stat { const char *string; u8 reg; @@ -268,6 +388,9 @@ struct kszphy_type { u16 interrupt_level_mask; u16 cable_diag_reg; unsigned long pair_mask; + u16 disable_dll_tx_bit; + u16 disable_dll_rx_bit; + u16 disable_dll_mask; bool has_broadcast_disable; bool has_nand_tree_disable; bool has_rmii_ref_clk_sel; @@ -278,13 +401,9 @@ struct lan8814_shared_priv { struct phy_device *phydev; struct ptp_clock *ptp_clock; struct ptp_clock_info ptp_clock_info; + struct ptp_pin_desc *pin_config; - /* Reference counter to how many ports in the package are enabling the - * timestamping - */ - u8 ref; - - /* Lock for ptp_clock and ref */ + /* Lock for ptp_clock */ struct mutex shared_lock; }; @@ -310,16 +429,53 @@ struct kszphy_ptp_priv { enum hwtstamp_rx_filters rx_filter; int layer; int version; + + struct ptp_clock *ptp_clock; + struct ptp_clock_info ptp_clock_info; + /* Lock for ptp_clock */ + struct mutex ptp_lock; + struct ptp_pin_desc *pin_config; + + s64 seconds; + /* Lock for accessing seconds */ + spinlock_t seconds_lock; +}; + +struct kszphy_phy_stats { + u64 rx_err_pkt_cnt; }; struct kszphy_priv { struct kszphy_ptp_priv ptp_priv; const struct kszphy_type *type; + struct clk *clk; int led_mode; u16 vct_ctrl1000; bool rmii_ref_clk_sel; bool rmii_ref_clk_sel_val; + bool clk_enable; + bool is_ptp_available; u64 stats[ARRAY_SIZE(kszphy_hw_stats)]; + struct kszphy_phy_stats phy_stats; +}; + +struct lan8842_phy_stats { + u64 rx_packets; + u64 rx_errors; + u64 tx_packets; + u64 tx_errors; +}; + +struct lan8842_priv { + struct lan8842_phy_stats phy_stats; + struct kszphy_ptp_priv ptp_priv; + u16 rev; +}; + +struct lanphy_reg_data { + int page; + u16 addr; + u16 val; }; static const struct kszphy_type lan8814_type = { @@ -351,6 +507,8 @@ static const struct kszphy_type ksz8051_type = { static const struct kszphy_type ksz8081_type = { .led_mode_reg = MII_KSZPHY_CTRL_2, + .cable_diag_reg = KSZ8081_LMD, + .pair_mask = KSZPHY_WIRE_PAIR_MASK, .has_broadcast_disable = true, .has_nand_tree_disable = true, .has_rmii_ref_clk_sel = true, @@ -364,6 +522,21 @@ static const struct kszphy_type ksz9021_type = { .interrupt_level_mask = BIT(14), }; +static const struct kszphy_type ksz9131_type = { + .interrupt_level_mask = BIT(14), + .disable_dll_tx_bit = BIT(12), + .disable_dll_rx_bit = BIT(12), + .disable_dll_mask = BIT_MASK(12), +}; + +static const struct kszphy_type lan8841_type = { + .disable_dll_tx_bit = BIT(14), + .disable_dll_rx_bit = BIT(14), + .disable_dll_mask = BIT_MASK(14), + .cable_diag_reg = LAN8814_CABLE_DIAG, + .pair_mask = LAN8814_WIRE_PAIR_MASK, +}; + static int kszphy_extended_write(struct phy_device *phydev, u32 regnum, u16 val) { @@ -412,11 +585,9 @@ static int kszphy_config_intr(struct phy_device *phydev) if (err) return err; - temp = KSZPHY_INTCS_ALL; - err = phy_write(phydev, MII_KSZPHY_INTCS, temp); + err = phy_write(phydev, MII_KSZPHY_INTCS, KSZPHY_INTCS_ALL); } else { - temp = 0; - err = phy_write(phydev, MII_KSZPHY_INTCS, temp); + err = phy_write(phydev, MII_KSZPHY_INTCS, 0); if (err) return err; @@ -615,7 +786,7 @@ static int ksz8051_ksz8795_match_phy_device(struct phy_device *phydev, { int ret; - if ((phydev->phy_id & MICREL_PHY_ID_MASK) != PHY_ID_KSZ8051) + if (!phy_id_compare(phydev->phy_id, PHY_ID_KSZ8051, MICREL_PHY_ID_MASK)) return 0; ret = phy_read(phydev, MII_BMSR); @@ -634,7 +805,8 @@ static int ksz8051_ksz8795_match_phy_device(struct phy_device *phydev, return !ret; } -static int ksz8051_match_phy_device(struct phy_device *phydev) +static int ksz8051_match_phy_device(struct phy_device *phydev, + const struct phy_driver *phydrv) { return ksz8051_ksz8795_match_phy_device(phydev, true); } @@ -736,6 +908,17 @@ static int ksz8061_config_init(struct phy_device *phydev) { int ret; + /* Chip can be powered down by the bootstrap code. */ + ret = phy_read(phydev, MII_BMCR); + if (ret < 0) + return ret; + if (ret & BMCR_PDOWN) { + ret = phy_write(phydev, MII_BMCR, ret & ~BMCR_PDOWN); + if (ret < 0) + return ret; + usleep_range(1000, 2000); + } + ret = phy_write_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_DEVID1, 0xB61A); if (ret) return ret; @@ -743,7 +926,8 @@ static int ksz8061_config_init(struct phy_device *phydev) return kszphy_config_init(phydev); } -static int ksz8795_match_phy_device(struct phy_device *phydev) +static int ksz8795_match_phy_device(struct phy_device *phydev, + const struct phy_driver *phydrv) { return ksz8051_ksz8795_match_phy_device(phydev, false); } @@ -878,7 +1062,7 @@ static int ksz9021_config_init(struct phy_device *phydev) #define TX_CLK_ID 0x1f /* set tx and tx_clk to "No delay adjustment" to keep 0ns - * dealy + * delay */ #define TX_ND 0x7 #define TX_CLK_ND 0xf @@ -887,6 +1071,29 @@ static int ksz9021_config_init(struct phy_device *phydev) #define MII_KSZ9031RN_EDPD 0x23 #define MII_KSZ9031RN_EDPD_ENABLE BIT(0) +static int ksz9031_set_loopback(struct phy_device *phydev, bool enable, + int speed) +{ + u16 ctl = BMCR_LOOPBACK; + int val; + + if (!enable) + return genphy_loopback(phydev, enable, 0); + + if (speed == SPEED_10 || speed == SPEED_100 || speed == SPEED_1000) + phydev->speed = speed; + else if (speed) + return -EINVAL; + phydev->duplex = DUPLEX_FULL; + + ctl |= mii_bmcr_encode_fixed(phydev->speed, phydev->duplex); + + phy_write(phydev, MII_BMCR, ctl); + + return phy_read_poll_timeout(phydev, MII_BMSR, val, val & BMSR_LSTATUS, + 5000, 500000, true); +} + static int ksz9031_of_load_skew_values(struct phy_device *phydev, const struct device_node *of_node, u16 reg, size_t field_sz, @@ -1172,19 +1379,18 @@ static int ksz9131_of_load_skew_values(struct phy_device *phydev, #define KSZ9131RN_MMD_COMMON_CTRL_REG 2 #define KSZ9131RN_RXC_DLL_CTRL 76 #define KSZ9131RN_TXC_DLL_CTRL 77 -#define KSZ9131RN_DLL_CTRL_BYPASS BIT_MASK(12) #define KSZ9131RN_DLL_ENABLE_DELAY 0 -#define KSZ9131RN_DLL_DISABLE_DELAY BIT(12) static int ksz9131_config_rgmii_delay(struct phy_device *phydev) { + const struct kszphy_type *type = phydev->drv->driver_data; u16 rxcdll_val, txcdll_val; int ret; switch (phydev->interface) { case PHY_INTERFACE_MODE_RGMII: - rxcdll_val = KSZ9131RN_DLL_DISABLE_DELAY; - txcdll_val = KSZ9131RN_DLL_DISABLE_DELAY; + rxcdll_val = type->disable_dll_rx_bit; + txcdll_val = type->disable_dll_tx_bit; break; case PHY_INTERFACE_MODE_RGMII_ID: rxcdll_val = KSZ9131RN_DLL_ENABLE_DELAY; @@ -1192,10 +1398,10 @@ static int ksz9131_config_rgmii_delay(struct phy_device *phydev) break; case PHY_INTERFACE_MODE_RGMII_RXID: rxcdll_val = KSZ9131RN_DLL_ENABLE_DELAY; - txcdll_val = KSZ9131RN_DLL_DISABLE_DELAY; + txcdll_val = type->disable_dll_tx_bit; break; case PHY_INTERFACE_MODE_RGMII_TXID: - rxcdll_val = KSZ9131RN_DLL_DISABLE_DELAY; + rxcdll_val = type->disable_dll_rx_bit; txcdll_val = KSZ9131RN_DLL_ENABLE_DELAY; break; default: @@ -1203,13 +1409,13 @@ static int ksz9131_config_rgmii_delay(struct phy_device *phydev) } ret = phy_modify_mmd(phydev, KSZ9131RN_MMD_COMMON_CTRL_REG, - KSZ9131RN_RXC_DLL_CTRL, KSZ9131RN_DLL_CTRL_BYPASS, + KSZ9131RN_RXC_DLL_CTRL, type->disable_dll_mask, rxcdll_val); if (ret < 0) return ret; return phy_modify_mmd(phydev, KSZ9131RN_MMD_COMMON_CTRL_REG, - KSZ9131RN_TXC_DLL_CTRL, KSZ9131RN_DLL_CTRL_BYPASS, + KSZ9131RN_TXC_DLL_CTRL, type->disable_dll_mask, txcdll_val); } @@ -1249,6 +1455,8 @@ static int ksz9131_config_init(struct phy_device *phydev) const struct device *dev_walker; int ret; + phydev->mdix_ctrl = ETH_TP_MDI_AUTO; + dev_walker = &phydev->mdio.dev; do { of_node = dev_walker->of_node; @@ -1298,28 +1506,30 @@ static int ksz9131_config_init(struct phy_device *phydev) #define MII_KSZ9131_AUTO_MDIX 0x1C #define MII_KSZ9131_AUTO_MDI_SET BIT(7) #define MII_KSZ9131_AUTO_MDIX_SWAP_OFF BIT(6) +#define MII_KSZ9131_DIG_AXAN_STS 0x14 +#define MII_KSZ9131_DIG_AXAN_STS_LINK_DET BIT(14) +#define MII_KSZ9131_DIG_AXAN_STS_A_SELECT BIT(12) static int ksz9131_mdix_update(struct phy_device *phydev) { int ret; - ret = phy_read(phydev, MII_KSZ9131_AUTO_MDIX); - if (ret < 0) - return ret; - - if (ret & MII_KSZ9131_AUTO_MDIX_SWAP_OFF) { - if (ret & MII_KSZ9131_AUTO_MDI_SET) - phydev->mdix_ctrl = ETH_TP_MDI; - else - phydev->mdix_ctrl = ETH_TP_MDI_X; + if (phydev->mdix_ctrl != ETH_TP_MDI_AUTO) { + phydev->mdix = phydev->mdix_ctrl; } else { - phydev->mdix_ctrl = ETH_TP_MDI_AUTO; - } + ret = phy_read(phydev, MII_KSZ9131_DIG_AXAN_STS); + if (ret < 0) + return ret; - if (ret & MII_KSZ9131_AUTO_MDI_SET) - phydev->mdix = ETH_TP_MDI; - else - phydev->mdix = ETH_TP_MDI_X; + if (ret & MII_KSZ9131_DIG_AXAN_STS_LINK_DET) { + if (ret & MII_KSZ9131_DIG_AXAN_STS_A_SELECT) + phydev->mdix = ETH_TP_MDI; + else + phydev->mdix = ETH_TP_MDI_X; + } else { + phydev->mdix = ETH_TP_MDI_INVALID; + } + } return 0; } @@ -1370,6 +1580,26 @@ static int ksz9131_config_aneg(struct phy_device *phydev) return genphy_config_aneg(phydev); } +static int ksz9477_get_features(struct phy_device *phydev) +{ + int ret; + + ret = genphy_read_abilities(phydev); + if (ret) + return ret; + + /* The "EEE control and capability 1" (Register 3.20) seems to be + * influenced by the "EEE advertisement 1" (Register 7.60). Changes + * on the 7.60 will affect 3.20. So, we need to construct our own list + * of caps. + * KSZ8563R should have 100BaseTX/Full only. + */ + linkmode_and(phydev->supported_eee, phydev->supported, + PHY_EEE_CAP1_FEATURES); + + return 0; +} + #define KSZ8873MLL_GLOBAL_CONTROL_4 0x06 #define KSZ8873MLL_GLOBAL_CONTROL_4_DUPLEX BIT(6) #define KSZ8873MLL_GLOBAL_CONTROL_4_SPEED BIT(4) @@ -1525,7 +1755,8 @@ static int ksz9x31_cable_test_fault_length(struct phy_device *phydev, u16 stat) * * distance to fault = (VCT_DATA - 22) * 4 / cable propagation velocity */ - if ((phydev->phy_id & MICREL_PHY_ID_MASK) == PHY_ID_KSZ9131) + if (phydev_id_compare(phydev, PHY_ID_KSZ9131) || + phydev_id_compare(phydev, PHY_ID_KSZ9477)) dt = clamp(dt - 22, 0, 255); return (dt * 400) / 10; @@ -1599,12 +1830,20 @@ static int ksz9x31_cable_test_get_status(struct phy_device *phydev, bool *finished) { struct kszphy_priv *priv = phydev->priv; - unsigned long pair_mask = 0xf; + unsigned long pair_mask; int retries = 20; int pair, ret, rv; *finished = false; + if (linkmode_test_bit(ETHTOOL_LINK_MODE_1000baseT_Full_BIT, + phydev->supported) || + linkmode_test_bit(ETHTOOL_LINK_MODE_1000baseT_Half_BIT, + phydev->supported)) + pair_mask = 0xf; /* All pairs */ + else + pair_mask = 0x3; /* Pairs A and B only */ + /* Try harder if link partner is active */ while (pair_mask && retries--) { for_each_set_bit(pair, &pair_mask, 4) { @@ -1685,6 +1924,28 @@ static int ksz886x_config_aneg(struct phy_device *phydev) if (ret) return ret; + if (phydev->autoneg != AUTONEG_ENABLE) { + /* When autonegotiation is disabled, we need to manually force + * the link state. If we don't do this, the PHY will keep + * sending Fast Link Pulses (FLPs) which are part of the + * autonegotiation process. This is not desired when + * autonegotiation is off. + */ + ret = phy_set_bits(phydev, MII_KSZPHY_CTRL, + KSZ886X_CTRL_FORCE_LINK); + if (ret) + return ret; + } else { + /* If we had previously forced the link state, we need to + * clear KSZ886X_CTRL_FORCE_LINK bit now. Otherwise, the PHY + * will not perform autonegotiation. + */ + ret = phy_clear_bits(phydev, MII_KSZPHY_CTRL, + KSZ886X_CTRL_FORCE_LINK); + if (ret) + return ret; + } + /* The MDI-X configuration is automatically changed by the PHY after * switching from autoneg off to on. So, take MDI-X configuration under * own control and set it after autoneg configuration was done. @@ -1733,6 +1994,143 @@ static int ksz886x_read_status(struct phy_device *phydev) return genphy_read_status(phydev); } +static int ksz9477_mdix_update(struct phy_device *phydev) +{ + if (phydev->mdix_ctrl != ETH_TP_MDI_AUTO) + phydev->mdix = phydev->mdix_ctrl; + else + phydev->mdix = ETH_TP_MDI_INVALID; + + return 0; +} + +static int ksz9477_read_mdix_ctrl(struct phy_device *phydev) +{ + int val; + + val = phy_read(phydev, MII_KSZ9131_AUTO_MDIX); + if (val < 0) + return val; + + if (!(val & MII_KSZ9131_AUTO_MDIX_SWAP_OFF)) + phydev->mdix_ctrl = ETH_TP_MDI_AUTO; + else if (val & MII_KSZ9131_AUTO_MDI_SET) + phydev->mdix_ctrl = ETH_TP_MDI; + else + phydev->mdix_ctrl = ETH_TP_MDI_X; + + return 0; +} + +static int ksz9477_read_status(struct phy_device *phydev) +{ + int ret; + + ret = ksz9477_mdix_update(phydev); + if (ret) + return ret; + + return genphy_read_status(phydev); +} + +static int ksz9477_config_aneg(struct phy_device *phydev) +{ + int ret; + + ret = ksz9131_config_mdix(phydev, phydev->mdix_ctrl); + if (ret) + return ret; + + return genphy_config_aneg(phydev); +} + +struct ksz9477_errata_write { + u8 dev_addr; + u8 reg_addr; + u16 val; +}; + +static const struct ksz9477_errata_write ksz9477_errata_writes[] = { + /* Register settings are needed to improve PHY receive performance */ + {0x01, 0x6f, 0xdd0b}, + {0x01, 0x8f, 0x6032}, + {0x01, 0x9d, 0x248c}, + {0x01, 0x75, 0x0060}, + {0x01, 0xd3, 0x7777}, + {0x1c, 0x06, 0x3008}, + {0x1c, 0x08, 0x2000}, + + /* Transmit waveform amplitude can be improved (1000BASE-T, 100BASE-TX, 10BASE-Te) */ + {0x1c, 0x04, 0x00d0}, + + /* Register settings are required to meet data sheet supply current specifications */ + {0x1c, 0x13, 0x6eff}, + {0x1c, 0x14, 0xe6ff}, + {0x1c, 0x15, 0x6eff}, + {0x1c, 0x16, 0xe6ff}, + {0x1c, 0x17, 0x00ff}, + {0x1c, 0x18, 0x43ff}, + {0x1c, 0x19, 0xc3ff}, + {0x1c, 0x1a, 0x6fff}, + {0x1c, 0x1b, 0x07ff}, + {0x1c, 0x1c, 0x0fff}, + {0x1c, 0x1d, 0xe7ff}, + {0x1c, 0x1e, 0xefff}, + {0x1c, 0x20, 0xeeee}, +}; + +static int ksz9477_phy_errata(struct phy_device *phydev) +{ + int err; + int i; + + /* Apply PHY settings to address errata listed in + * KSZ9477, KSZ9897, KSZ9896, KSZ9567, KSZ8565 + * Silicon Errata and Data Sheet Clarification documents. + * + * Document notes: Before configuring the PHY MMD registers, it is + * necessary to set the PHY to 100 Mbps speed with auto-negotiation + * disabled by writing to register 0xN100-0xN101. After writing the + * MMD registers, and after all errata workarounds that involve PHY + * register settings, write register 0xN100-0xN101 again to enable + * and restart auto-negotiation. + */ + err = phy_write(phydev, MII_BMCR, BMCR_SPEED100 | BMCR_FULLDPLX); + if (err) + return err; + + for (i = 0; i < ARRAY_SIZE(ksz9477_errata_writes); ++i) { + const struct ksz9477_errata_write *errata = &ksz9477_errata_writes[i]; + + err = phy_write_mmd(phydev, errata->dev_addr, errata->reg_addr, errata->val); + if (err) + return err; + } + + return genphy_restart_aneg(phydev); +} + +static int ksz9477_config_init(struct phy_device *phydev) +{ + int err; + + /* Only KSZ9897 family of switches needs this fix. */ + if ((phydev->phy_id & 0xf) == 1) { + err = ksz9477_phy_errata(phydev); + if (err) + return err; + } + + /* Read initial MDI-X config state. So, we do not need to poll it + * later on. + */ + err = ksz9477_read_mdix_ctrl(phydev); + if (err) + return err; + + return kszphy_config_init(phydev); +} + static int kszphy_get_sset_count(struct phy_device *phydev) { return ARRAY_SIZE(kszphy_hw_stats); @@ -1742,10 +2140,8 @@ static void kszphy_get_strings(struct phy_device *phydev, u8 *data) { int i; - for (i = 0; i < ARRAY_SIZE(kszphy_hw_stats); i++) { - strscpy(data + i * ETH_GSTRING_LEN, - kszphy_hw_stats[i].string, ETH_GSTRING_LEN); - } + for (i = 0; i < ARRAY_SIZE(kszphy_hw_stats); i++) + ethtool_puts(&data, kszphy_hw_stats[i].string); } static u64 kszphy_get_stat(struct phy_device *phydev, int i) @@ -1776,6 +2172,305 @@ static void kszphy_get_stats(struct phy_device *phydev, data[i] = kszphy_get_stat(phydev, i); } +/* KSZ9477 PHY RXER Counter. Probably supported by other PHYs like KSZ9313, + * etc. The counter is incremented when the PHY receives a frame with one or + * more symbol errors. The counter is cleared when the register is read. + */ +#define MII_KSZ9477_PHY_RXER_COUNTER 0x15 + +static int kszphy_update_stats(struct phy_device *phydev) +{ + struct kszphy_priv *priv = phydev->priv; + int ret; + + ret = phy_read(phydev, MII_KSZ9477_PHY_RXER_COUNTER); + if (ret < 0) + return ret; + + priv->phy_stats.rx_err_pkt_cnt += ret; + + return 0; +} + +static void kszphy_get_phy_stats(struct phy_device *phydev, + struct ethtool_eth_phy_stats *eth_stats, + struct ethtool_phy_stats *stats) +{ + struct kszphy_priv *priv = phydev->priv; + + stats->rx_errors = priv->phy_stats.rx_err_pkt_cnt; +} + +/* Base register for Signal Quality Indicator (SQI) - Channel A + * + * MMD Address: MDIO_MMD_PMAPMD (0x01) + * Register: 0xAC (Channel A) + * Each channel (pair) has its own register: + * Channel A: 0xAC + * Channel B: 0xAD + * Channel C: 0xAE + * Channel D: 0xAF + */ +#define KSZ9477_MMD_SIGNAL_QUALITY_CHAN_A 0xac + +/* SQI field mask for bits [14:8] + * + * SQI indicates relative quality of the signal. + * A lower value indicates better signal quality. + */ +#define KSZ9477_MMD_SQI_MASK GENMASK(14, 8) + +#define KSZ9477_MAX_CHANNELS 4 +#define KSZ9477_SQI_MAX 7 + +/* Number of SQI samples to average for a stable result. + * + * Reference: KSZ9477S Datasheet DS00002392C, Section 4.1.11 (page 26) + * For noisy environments, a minimum of 30–50 readings is recommended. + */ +#define KSZ9477_SQI_SAMPLE_COUNT 40 + +/* The hardware SQI register provides a raw value from 0-127, where a lower + * value indicates better signal quality. However, empirical testing has + * shown that only the 0-7 range is relevant for a functional link. A raw + * value of 8 or higher was measured directly before link drop. This aligns + * with the OPEN Alliance recommendation that SQI=0 should represent the + * pre-failure state. + * + * This table provides a non-linear mapping from the useful raw hardware + * values (0-7) to the standard 0-7 SQI scale, where higher is better. + */ +static const u8 ksz_sqi_mapping[] = { + 7, /* raw 0 -> SQI 7 */ + 7, /* raw 1 -> SQI 7 */ + 6, /* raw 2 -> SQI 6 */ + 5, /* raw 3 -> SQI 5 */ + 4, /* raw 4 -> SQI 4 */ + 3, /* raw 5 -> SQI 3 */ + 2, /* raw 6 -> SQI 2 */ + 1, /* raw 7 -> SQI 1 */ +}; + +/** + * kszphy_get_sqi - Read, average, and map Signal Quality Index (SQI) + * @phydev: the PHY device + * + * This function reads and processes the raw Signal Quality Index from the + * PHY. Based on empirical testing, a raw value of 8 or higher indicates a + * pre-failure state and is mapped to SQI 0. Raw values from 0-7 are + * mapped to the standard 0-7 SQI scale via a lookup table. + * + * Return: SQI value (0–7), or a negative errno on failure. + */ +static int kszphy_get_sqi(struct phy_device *phydev) +{ + int sum[KSZ9477_MAX_CHANNELS] = { 0 }; + int worst_sqi = KSZ9477_SQI_MAX; + int i, val, raw_sqi, ch; + u8 channels; + + /* Determine applicable channels based on link speed */ + if (phydev->speed == SPEED_1000) + channels = 4; + else if (phydev->speed == SPEED_100) + channels = 1; + else + return -EOPNOTSUPP; + + /* Sample and accumulate SQI readings for each pair (currently only one). + * + * Reference: KSZ9477S Datasheet DS00002392C, Section 4.1.11 (page 26) + * - The SQI register is updated every 2 µs. + * - Values may fluctuate significantly, even in low-noise environments. + * - For reliable estimation, average a minimum of 30–50 samples + * (recommended for noisy environments) + * - In noisy environments, individual readings are highly unreliable. + * + * We use 40 samples per pair with a delay of 3 µs between each + * read to ensure new values are captured (2 µs update interval). + */ + for (i = 0; i < KSZ9477_SQI_SAMPLE_COUNT; i++) { + for (ch = 0; ch < channels; ch++) { + val = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, + KSZ9477_MMD_SIGNAL_QUALITY_CHAN_A + ch); + if (val < 0) + return val; + + raw_sqi = FIELD_GET(KSZ9477_MMD_SQI_MASK, val); + sum[ch] += raw_sqi; + + /* We communicate with the PHY via MDIO via SPI or + * I2C, which is relatively slow. At least slower than + * the update interval of the SQI register. + * So, we can skip the delay between reads. + */ + } + } + + /* Calculate average for each channel and find the worst SQI */ + for (ch = 0; ch < channels; ch++) { + int avg_raw_sqi = sum[ch] / KSZ9477_SQI_SAMPLE_COUNT; + int mapped_sqi; + + /* Handle the pre-fail/failed state first. */ + if (avg_raw_sqi >= ARRAY_SIZE(ksz_sqi_mapping)) + mapped_sqi = 0; + else + /* Use the lookup table for the good signal range. */ + mapped_sqi = ksz_sqi_mapping[avg_raw_sqi]; + + if (mapped_sqi < worst_sqi) + worst_sqi = mapped_sqi; + } + + return worst_sqi; +} + +static int kszphy_get_sqi_max(struct phy_device *phydev) +{ + return KSZ9477_SQI_MAX; +} + +static int kszphy_get_mse_capability(struct phy_device *phydev, + struct phy_mse_capability *cap) +{ + /* Capabilities depend on link mode: + * - 1000BASE-T: per-pair SQI registers exist => expose A..D + * and a WORST selector. + * - 100BASE-TX: HW provides a single MSE/SQI reading in the "channel A" + * register, but with auto MDI-X there is no MDI-X resolution bit, + * so we cannot map that register to a specific wire pair reliably. + * To avoid misleading per-channel data, advertise only LINK. + * Other speeds: no MSE exposure via this driver. + * + * Note: WORST is *not* a hardware selector on this family. + * We expose it because the driver computes it in software + * by scanning per-channel readouts (A..D) and picking the + * maximum average MSE. + */ + if (phydev->speed == SPEED_1000) + cap->supported_caps = PHY_MSE_CAP_CHANNEL_A | + PHY_MSE_CAP_CHANNEL_B | + PHY_MSE_CAP_CHANNEL_C | + PHY_MSE_CAP_CHANNEL_D | + PHY_MSE_CAP_WORST_CHANNEL; + else if (phydev->speed == SPEED_100) + cap->supported_caps = PHY_MSE_CAP_LINK; + else + return -EOPNOTSUPP; + + cap->max_average_mse = FIELD_MAX(KSZ9477_MMD_SQI_MASK); + cap->refresh_rate_ps = 2000000; /* 2 us */ + /* Estimated from link modulation (125 MBd per channel) and documented + * refresh rate of 2 us + */ + cap->num_symbols = 250; + + cap->supported_caps |= PHY_MSE_CAP_AVG; + + return 0; +} + +static int kszphy_get_mse_snapshot(struct phy_device *phydev, + enum phy_mse_channel channel, + struct phy_mse_snapshot *snapshot) +{ + u8 num_channels; + int ret; + + if (phydev->speed == SPEED_1000) + num_channels = 4; + else if (phydev->speed == SPEED_100) + num_channels = 1; + else + return -EOPNOTSUPP; + + if (channel == PHY_MSE_CHANNEL_WORST) { + u32 worst_val = 0; + int i; + + /* WORST is implemented in software: select the maximum + * average MSE across the available per-channel registers. + * Only defined when multiple channels exist (1000BASE-T). + */ + if (num_channels < 2) + return -EOPNOTSUPP; + + for (i = 0; i < num_channels; i++) { + ret = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, + KSZ9477_MMD_SIGNAL_QUALITY_CHAN_A + i); + if (ret < 0) + return ret; + + ret = FIELD_GET(KSZ9477_MMD_SQI_MASK, ret); + if (ret > worst_val) + worst_val = ret; + } + snapshot->average_mse = worst_val; + } else if (channel == PHY_MSE_CHANNEL_LINK && num_channels == 1) { + ret = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, + KSZ9477_MMD_SIGNAL_QUALITY_CHAN_A); + if (ret < 0) + return ret; + snapshot->average_mse = FIELD_GET(KSZ9477_MMD_SQI_MASK, ret); + } else if (channel >= PHY_MSE_CHANNEL_A && + channel <= PHY_MSE_CHANNEL_D) { + /* Per-channel readouts are valid only for 1000BASE-T. */ + if (phydev->speed != SPEED_1000) + return -EOPNOTSUPP; + + ret = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, + KSZ9477_MMD_SIGNAL_QUALITY_CHAN_A + channel); + if (ret < 0) + return ret; + snapshot->average_mse = FIELD_GET(KSZ9477_MMD_SQI_MASK, ret); + } else { + return -EOPNOTSUPP; + } + + return 0; +} + +static void kszphy_enable_clk(struct phy_device *phydev) +{ + struct kszphy_priv *priv = phydev->priv; + + if (!priv->clk_enable && priv->clk) { + clk_prepare_enable(priv->clk); + priv->clk_enable = true; + } +} + +static void kszphy_disable_clk(struct phy_device *phydev) +{ + struct kszphy_priv *priv = phydev->priv; + + if (priv->clk_enable && priv->clk) { + clk_disable_unprepare(priv->clk); + priv->clk_enable = false; + } +} + +static int kszphy_generic_resume(struct phy_device *phydev) +{ + kszphy_enable_clk(phydev); + + return genphy_resume(phydev); +} + +static int kszphy_generic_suspend(struct phy_device *phydev) +{ + int ret; + + ret = genphy_suspend(phydev); + if (ret) + return ret; + + kszphy_disable_clk(phydev); + + return 0; +} + static int kszphy_suspend(struct phy_device *phydev) { /* Disable PHY Interrupts */ @@ -1785,7 +2480,7 @@ static int kszphy_suspend(struct phy_device *phydev) phydev->drv->config_intr(phydev); } - return genphy_suspend(phydev); + return kszphy_generic_suspend(phydev); } static void kszphy_parse_led_mode(struct phy_device *phydev) @@ -1816,7 +2511,9 @@ static int kszphy_resume(struct phy_device *phydev) { int ret; - genphy_resume(phydev); + ret = kszphy_generic_resume(phydev); + if (ret) + return ret; /* After switching from power-down to normal mode, an internal global * reset is automatically generated. Wait a minimum of 1 ms before @@ -1838,6 +2535,97 @@ static int kszphy_resume(struct phy_device *phydev) return 0; } +/* Because of errata DS80000700A, receiver error following software + * power down. Suspend and resume callbacks only disable and enable + * external rmii reference clock. + */ +static int ksz8041_resume(struct phy_device *phydev) +{ + kszphy_enable_clk(phydev); + + return 0; +} + +static int ksz8041_suspend(struct phy_device *phydev) +{ + kszphy_disable_clk(phydev); + + return 0; +} + +static int ksz9477_resume(struct phy_device *phydev) +{ + int ret; + + /* No need to initialize registers if not powered down. */ + ret = phy_read(phydev, MII_BMCR); + if (ret < 0) + return ret; + if (!(ret & BMCR_PDOWN)) + return 0; + + genphy_resume(phydev); + + /* After switching from power-down to normal mode, an internal global + * reset is automatically generated. Wait a minimum of 1 ms before + * read/write access to the PHY registers. + */ + usleep_range(1000, 2000); + + /* Only KSZ9897 family of switches needs this fix. */ + if ((phydev->phy_id & 0xf) == 1) { + ret = ksz9477_phy_errata(phydev); + if (ret) + return ret; + } + + /* Enable PHY Interrupts */ + if (phy_interrupt_is_valid(phydev)) { + phydev->interrupts = PHY_INTERRUPT_ENABLED; + if (phydev->drv->config_intr) + phydev->drv->config_intr(phydev); + } + + return 0; +} + +static int ksz8061_resume(struct phy_device *phydev) +{ + int ret; + + /* This function can be called twice when the Ethernet device is on. */ + ret = phy_read(phydev, MII_BMCR); + if (ret < 0) + return ret; + if (!(ret & BMCR_PDOWN)) + return 0; + + ret = kszphy_generic_resume(phydev); + if (ret) + return ret; + + usleep_range(1000, 2000); + + /* Re-program the value after chip is reset. */ + ret = phy_write_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_DEVID1, 0xB61A); + if (ret) + return ret; + + /* Enable PHY Interrupts */ + if (phy_interrupt_is_valid(phydev)) { + phydev->interrupts = PHY_INTERRUPT_ENABLED; + if (phydev->drv->config_intr) + phydev->drv->config_intr(phydev); + } + + return 0; +} + +static int ksz8061_suspend(struct phy_device *phydev) +{ + return kszphy_suspend(phydev); +} + static int kszphy_probe(struct phy_device *phydev) { const struct kszphy_type *type = phydev->drv->driver_data; @@ -1855,7 +2643,7 @@ static int kszphy_probe(struct phy_device *phydev) kszphy_parse_led_mode(phydev); - clk = devm_clk_get(&phydev->mdio.dev, "rmii-ref"); + clk = devm_clk_get_optional_enabled(&phydev->mdio.dev, "rmii-ref"); /* NOTE: clk may be NULL if building without CONFIG_HAVE_CLK */ if (!IS_ERR_OR_NULL(clk)) { unsigned long rate = clk_get_rate(clk); @@ -1875,8 +2663,17 @@ static int kszphy_probe(struct phy_device *phydev) rate); return -EINVAL; } + } else if (!clk) { + /* unnamed clock from the generic ethernet-phy binding */ + clk = devm_clk_get_optional_enabled(&phydev->mdio.dev, NULL); } + if (IS_ERR(clk)) + return PTR_ERR(clk); + + clk_disable_unprepare(clk); + priv->clk = clk; + if (ksz8041_fiber_mode(phydev)) phydev->port = PORT_FIBRE; @@ -1957,7 +2754,7 @@ static __always_inline int ksz886x_cable_test_fault_length(struct phy_device *ph */ dt = FIELD_GET(data_mask, status); - if ((phydev->phy_id & MICREL_PHY_ID_MASK) == PHY_ID_LAN8814) + if (phydev_id_compare(phydev, PHY_ID_LAN8814)) return ((dt - 22) * 800) / 10; else return (dt * 400) / 10; @@ -2088,7 +2885,8 @@ static int ksz886x_cable_test_get_status(struct phy_device *phydev, const struct kszphy_type *type = phydev->drv->driver_data; unsigned long pair_mask = type->pair_mask; int retries = 20; - int pair, ret; + int ret = 0; + int pair; *finished = false; @@ -2118,10 +2916,80 @@ static int ksz886x_cable_test_get_status(struct phy_device *phydev, return ret; } +/** + * LAN8814_PAGE_PCS - Selects Extended Page 0. + * + * This page contains timers used for auto-negotiation, debug registers and + * register to configure fast link failure. + */ +#define LAN8814_PAGE_PCS 0 + +/** + * LAN8814_PAGE_AFE_PMA - Selects Extended Page 1. + * + * This page appears to control the Analog Front-End (AFE) and Physical + * Medium Attachment (PMA) layers. It is used to access registers like + * LAN8814_PD_CONTROLS and LAN8814_LINK_QUALITY. + */ +#define LAN8814_PAGE_AFE_PMA 1 + +/** + * LAN8814_PAGE_PCS_DIGITAL - Selects Extended Page 2. + * + * This page seems dedicated to the Physical Coding Sublayer (PCS) and other + * digital logic. It is used for MDI-X alignment (LAN8814_ALIGN_SWAP) and EEE + * state (LAN8814_EEE_STATE) in the LAN8814, and is repurposed for statistics + * and self-test counters in the LAN8842. + */ +#define LAN8814_PAGE_PCS_DIGITAL 2 + +/** + * LAN8814_PAGE_EEE - Selects Extended Page 3. + * + * This page contains EEE registers + */ +#define LAN8814_PAGE_EEE 3 + +/** + * LAN8814_PAGE_COMMON_REGS - Selects Extended Page 4. + * + * This page contains device-common registers that affect the entire chip. + * It includes controls for chip-level resets, strap status, GPIO, + * QSGMII, the shared 1588 PTP block, and the PVT monitor. + */ +#define LAN8814_PAGE_COMMON_REGS 4 + +/** + * LAN8814_PAGE_PORT_REGS - Selects Extended Page 5. + * + * This page contains port-specific registers that must be accessed + * on a per-port basis. It includes controls for port LEDs, QSGMII PCS, + * rate adaptation FIFOs, and the per-port 1588 TSU block. + */ +#define LAN8814_PAGE_PORT_REGS 5 + +/** + * LAN8814_PAGE_POWER_REGS - Selects Extended Page 28. + * + * This page contains analog control registers and power mode registers. + */ +#define LAN8814_PAGE_POWER_REGS 28 + +/** + * LAN8814_PAGE_SYSTEM_CTRL - Selects Extended Page 31. + * + * This page appears to hold fundamental system or global controls. In the + * driver, it is used by the related LAN8804 to access the + * LAN8814_CLOCK_MANAGEMENT register. + */ +#define LAN8814_PAGE_SYSTEM_CTRL 31 + #define LAN_EXT_PAGE_ACCESS_CONTROL 0x16 #define LAN_EXT_PAGE_ACCESS_ADDRESS_DATA 0x17 #define LAN_EXT_PAGE_ACCESS_CTRL_EP_FUNC 0x4000 +#define LAN8814_QSGMII_TX_CONFIG 0x35 +#define LAN8814_QSGMII_TX_CONFIG_QSGMII BIT(3) #define LAN8814_QSGMII_SOFT_RESET 0x43 #define LAN8814_QSGMII_SOFT_RESET_BIT BIT(0) #define LAN8814_QSGMII_PCS1G_ANEG_CONFIG 0x13 @@ -2168,6 +3036,27 @@ static int lanphy_write_page_reg(struct phy_device *phydev, int page, u16 addr, return val; } +static int lanphy_modify_page_reg(struct phy_device *phydev, int page, u16 addr, + u16 mask, u16 set) +{ + int ret; + + phy_lock_mdio_bus(phydev); + __phy_write(phydev, LAN_EXT_PAGE_ACCESS_CONTROL, page); + __phy_write(phydev, LAN_EXT_PAGE_ACCESS_ADDRESS_DATA, addr); + __phy_write(phydev, LAN_EXT_PAGE_ACCESS_CONTROL, + (page | LAN_EXT_PAGE_ACCESS_CTRL_EP_FUNC)); + ret = __phy_modify_changed(phydev, LAN_EXT_PAGE_ACCESS_ADDRESS_DATA, + mask, set); + phy_unlock_mdio_bus(phydev); + + if (ret < 0) + phydev_err(phydev, "__phy_modify_changed() failed: %pe\n", + ERR_PTR(ret)); + + return ret; +} + static int lan8814_config_ts_intr(struct phy_device *phydev, bool enable) { u16 val = 0; @@ -2178,42 +3067,52 @@ static int lan8814_config_ts_intr(struct phy_device *phydev, bool enable) PTP_TSU_INT_EN_PTP_RX_TS_EN_ | PTP_TSU_INT_EN_PTP_RX_TS_OVRFL_EN_; - return lanphy_write_page_reg(phydev, 5, PTP_TSU_INT_EN, val); + return lanphy_write_page_reg(phydev, LAN8814_PAGE_PORT_REGS, + PTP_TSU_INT_EN, val); } static void lan8814_ptp_rx_ts_get(struct phy_device *phydev, u32 *seconds, u32 *nano_seconds, u16 *seq_id) { - *seconds = lanphy_read_page_reg(phydev, 5, PTP_RX_INGRESS_SEC_HI); + *seconds = lanphy_read_page_reg(phydev, LAN8814_PAGE_PORT_REGS, + PTP_RX_INGRESS_SEC_HI); *seconds = (*seconds << 16) | - lanphy_read_page_reg(phydev, 5, PTP_RX_INGRESS_SEC_LO); + lanphy_read_page_reg(phydev, LAN8814_PAGE_PORT_REGS, + PTP_RX_INGRESS_SEC_LO); - *nano_seconds = lanphy_read_page_reg(phydev, 5, PTP_RX_INGRESS_NS_HI); + *nano_seconds = lanphy_read_page_reg(phydev, LAN8814_PAGE_PORT_REGS, + PTP_RX_INGRESS_NS_HI); *nano_seconds = ((*nano_seconds & 0x3fff) << 16) | - lanphy_read_page_reg(phydev, 5, PTP_RX_INGRESS_NS_LO); + lanphy_read_page_reg(phydev, LAN8814_PAGE_PORT_REGS, + PTP_RX_INGRESS_NS_LO); - *seq_id = lanphy_read_page_reg(phydev, 5, PTP_RX_MSG_HEADER2); + *seq_id = lanphy_read_page_reg(phydev, LAN8814_PAGE_PORT_REGS, + PTP_RX_MSG_HEADER2); } static void lan8814_ptp_tx_ts_get(struct phy_device *phydev, u32 *seconds, u32 *nano_seconds, u16 *seq_id) { - *seconds = lanphy_read_page_reg(phydev, 5, PTP_TX_EGRESS_SEC_HI); + *seconds = lanphy_read_page_reg(phydev, LAN8814_PAGE_PORT_REGS, + PTP_TX_EGRESS_SEC_HI); *seconds = *seconds << 16 | - lanphy_read_page_reg(phydev, 5, PTP_TX_EGRESS_SEC_LO); + lanphy_read_page_reg(phydev, LAN8814_PAGE_PORT_REGS, + PTP_TX_EGRESS_SEC_LO); - *nano_seconds = lanphy_read_page_reg(phydev, 5, PTP_TX_EGRESS_NS_HI); + *nano_seconds = lanphy_read_page_reg(phydev, LAN8814_PAGE_PORT_REGS, + PTP_TX_EGRESS_NS_HI); *nano_seconds = ((*nano_seconds & 0x3fff) << 16) | - lanphy_read_page_reg(phydev, 5, PTP_TX_EGRESS_NS_LO); + lanphy_read_page_reg(phydev, LAN8814_PAGE_PORT_REGS, + PTP_TX_EGRESS_NS_LO); - *seq_id = lanphy_read_page_reg(phydev, 5, PTP_TX_MSG_HEADER2); + *seq_id = lanphy_read_page_reg(phydev, LAN8814_PAGE_PORT_REGS, + PTP_TX_MSG_HEADER2); } -static int lan8814_ts_info(struct mii_timestamper *mii_ts, struct ethtool_ts_info *info) +static int lan8814_ts_info(struct mii_timestamper *mii_ts, struct kernel_ethtool_ts_info *info) { struct kszphy_ptp_priv *ptp_priv = container_of(mii_ts, struct kszphy_ptp_priv, mii_ts); - struct phy_device *phydev = ptp_priv->phydev; - struct lan8814_shared_priv *shared = phydev->shared->priv; + struct lan8814_shared_priv *shared = phy_package_get_priv(ptp_priv->phydev); info->so_timestamping = SOF_TIMESTAMPING_TX_HARDWARE | SOF_TIMESTAMPING_RX_HARDWARE | @@ -2241,31 +3140,27 @@ static void lan8814_flush_fifo(struct phy_device *phydev, bool egress) int i; for (i = 0; i < FIFO_SIZE; ++i) - lanphy_read_page_reg(phydev, 5, + lanphy_read_page_reg(phydev, LAN8814_PAGE_PORT_REGS, egress ? PTP_TX_MSG_HEADER2 : PTP_RX_MSG_HEADER2); /* Read to clear overflow status bit */ - lanphy_read_page_reg(phydev, 5, PTP_TSU_INT_STS); + lanphy_read_page_reg(phydev, LAN8814_PAGE_PORT_REGS, PTP_TSU_INT_STS); } -static int lan8814_hwtstamp(struct mii_timestamper *mii_ts, struct ifreq *ifr) +static int lan8814_hwtstamp_set(struct mii_timestamper *mii_ts, + struct kernel_hwtstamp_config *config, + struct netlink_ext_ack *extack) { struct kszphy_ptp_priv *ptp_priv = container_of(mii_ts, struct kszphy_ptp_priv, mii_ts); - struct phy_device *phydev = ptp_priv->phydev; - struct lan8814_shared_priv *shared = phydev->shared->priv; struct lan8814_ptp_rx_ts *rx_ts, *tmp; - struct hwtstamp_config config; int txcfg = 0, rxcfg = 0; int pkt_ts_enable; - if (copy_from_user(&config, ifr->ifr_data, sizeof(config))) - return -EFAULT; - - ptp_priv->hwts_tx_type = config.tx_type; - ptp_priv->rx_filter = config.rx_filter; + ptp_priv->hwts_tx_type = config->tx_type; + ptp_priv->rx_filter = config->rx_filter; - switch (config.rx_filter) { + switch (config->rx_filter) { case HWTSTAMP_FILTER_NONE: ptp_priv->layer = 0; ptp_priv->version = 0; @@ -2299,37 +3194,35 @@ static int lan8814_hwtstamp(struct mii_timestamper *mii_ts, struct ifreq *ifr) rxcfg |= PTP_RX_PARSE_CONFIG_IPV4_EN_ | PTP_RX_PARSE_CONFIG_IPV6_EN_; txcfg |= PTP_TX_PARSE_CONFIG_IPV4_EN_ | PTP_TX_PARSE_CONFIG_IPV6_EN_; } - lanphy_write_page_reg(ptp_priv->phydev, 5, PTP_RX_PARSE_CONFIG, rxcfg); - lanphy_write_page_reg(ptp_priv->phydev, 5, PTP_TX_PARSE_CONFIG, txcfg); + lanphy_write_page_reg(ptp_priv->phydev, LAN8814_PAGE_PORT_REGS, + PTP_RX_PARSE_CONFIG, rxcfg); + lanphy_write_page_reg(ptp_priv->phydev, LAN8814_PAGE_PORT_REGS, + PTP_TX_PARSE_CONFIG, txcfg); pkt_ts_enable = PTP_TIMESTAMP_EN_SYNC_ | PTP_TIMESTAMP_EN_DREQ_ | PTP_TIMESTAMP_EN_PDREQ_ | PTP_TIMESTAMP_EN_PDRES_; - lanphy_write_page_reg(ptp_priv->phydev, 5, PTP_RX_TIMESTAMP_EN, pkt_ts_enable); - lanphy_write_page_reg(ptp_priv->phydev, 5, PTP_TX_TIMESTAMP_EN, pkt_ts_enable); - - if (ptp_priv->hwts_tx_type == HWTSTAMP_TX_ONESTEP_SYNC) - lanphy_write_page_reg(ptp_priv->phydev, 5, PTP_TX_MOD, - PTP_TX_MOD_TX_PTP_SYNC_TS_INSERT_); + lanphy_write_page_reg(ptp_priv->phydev, LAN8814_PAGE_PORT_REGS, + PTP_RX_TIMESTAMP_EN, pkt_ts_enable); + lanphy_write_page_reg(ptp_priv->phydev, LAN8814_PAGE_PORT_REGS, + PTP_TX_TIMESTAMP_EN, pkt_ts_enable); + + if (ptp_priv->hwts_tx_type == HWTSTAMP_TX_ONESTEP_SYNC) { + lanphy_modify_page_reg(ptp_priv->phydev, LAN8814_PAGE_PORT_REGS, + PTP_TX_MOD, + PTP_TX_MOD_TX_PTP_SYNC_TS_INSERT_, + PTP_TX_MOD_TX_PTP_SYNC_TS_INSERT_); + } else if (ptp_priv->hwts_tx_type == HWTSTAMP_TX_ON) { + lanphy_modify_page_reg(ptp_priv->phydev, LAN8814_PAGE_PORT_REGS, + PTP_TX_MOD, + PTP_TX_MOD_TX_PTP_SYNC_TS_INSERT_, + 0); + } - if (config.rx_filter != HWTSTAMP_FILTER_NONE) + if (config->rx_filter != HWTSTAMP_FILTER_NONE) lan8814_config_ts_intr(ptp_priv->phydev, true); else lan8814_config_ts_intr(ptp_priv->phydev, false); - mutex_lock(&shared->shared_lock); - if (config.rx_filter != HWTSTAMP_FILTER_NONE) - shared->ref++; - else - shared->ref--; - - if (shared->ref) - lanphy_write_page_reg(ptp_priv->phydev, 4, PTP_CMD_CTL, - PTP_CMD_CTL_PTP_ENABLE_); - else - lanphy_write_page_reg(ptp_priv->phydev, 4, PTP_CMD_CTL, - PTP_CMD_CTL_PTP_DISABLE_); - mutex_unlock(&shared->shared_lock); - /* In case of multiple starts and stops, these needs to be cleared */ list_for_each_entry_safe(rx_ts, tmp, &ptp_priv->rx_ts_list, list) { list_del(&rx_ts->list); @@ -2341,7 +3234,7 @@ static int lan8814_hwtstamp(struct mii_timestamper *mii_ts, struct ifreq *ifr) lan8814_flush_fifo(ptp_priv->phydev, false); lan8814_flush_fifo(ptp_priv->phydev, true); - return copy_to_user(ifr->ifr_data, &config, sizeof(config)) ? -EFAULT : 0; + return 0; } static void lan8814_txtstamp(struct mii_timestamper *mii_ts, @@ -2367,7 +3260,7 @@ static void lan8814_txtstamp(struct mii_timestamper *mii_ts, } } -static void lan8814_get_sig_rx(struct sk_buff *skb, u16 *sig) +static bool lan8814_get_sig_rx(struct sk_buff *skb, u16 *sig) { struct ptp_header *ptp_header; u32 type; @@ -2377,11 +3270,15 @@ static void lan8814_get_sig_rx(struct sk_buff *skb, u16 *sig) ptp_header = ptp_parse_header(skb, type); skb_pull_inline(skb, ETH_HLEN); + if (!ptp_header) + return false; + *sig = (__force u16)(ntohs(ptp_header->sequence_id)); + return true; } -static bool lan8814_match_rx_ts(struct kszphy_ptp_priv *ptp_priv, - struct sk_buff *skb) +static bool lan8814_match_rx_skb(struct kszphy_ptp_priv *ptp_priv, + struct sk_buff *skb) { struct skb_shared_hwtstamps *shhwtstamps; struct lan8814_ptp_rx_ts *rx_ts, *tmp; @@ -2389,7 +3286,8 @@ static bool lan8814_match_rx_ts(struct kszphy_ptp_priv *ptp_priv, bool ret = false; u16 skb_sig; - lan8814_get_sig_rx(skb, &skb_sig); + if (!lan8814_get_sig_rx(skb, &skb_sig)) + return ret; /* Iterate over all RX timestamps and match it with the received skbs */ spin_lock_irqsave(&ptp_priv->rx_ts_lock, flags); @@ -2430,42 +3328,50 @@ static bool lan8814_rxtstamp(struct mii_timestamper *mii_ts, struct sk_buff *skb /* If we failed to match then add it to the queue for when the timestamp * will come */ - if (!lan8814_match_rx_ts(ptp_priv, skb)) + if (!lan8814_match_rx_skb(ptp_priv, skb)) skb_queue_tail(&ptp_priv->rx_queue, skb); return true; } static void lan8814_ptp_clock_set(struct phy_device *phydev, - u32 seconds, u32 nano_seconds) + time64_t sec, u32 nsec) { - u32 sec_low, sec_high, nsec_low, nsec_high; - - sec_low = seconds & 0xffff; - sec_high = (seconds >> 16) & 0xffff; - nsec_low = nano_seconds & 0xffff; - nsec_high = (nano_seconds >> 16) & 0x3fff; - - lanphy_write_page_reg(phydev, 4, PTP_CLOCK_SET_SEC_LO, sec_low); - lanphy_write_page_reg(phydev, 4, PTP_CLOCK_SET_SEC_MID, sec_high); - lanphy_write_page_reg(phydev, 4, PTP_CLOCK_SET_NS_LO, nsec_low); - lanphy_write_page_reg(phydev, 4, PTP_CLOCK_SET_NS_HI, nsec_high); - - lanphy_write_page_reg(phydev, 4, PTP_CMD_CTL, PTP_CMD_CTL_PTP_CLOCK_LOAD_); + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_CLOCK_SET_SEC_LO, lower_16_bits(sec)); + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_CLOCK_SET_SEC_MID, upper_16_bits(sec)); + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_CLOCK_SET_SEC_HI, upper_32_bits(sec)); + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_CLOCK_SET_NS_LO, lower_16_bits(nsec)); + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_CLOCK_SET_NS_HI, upper_16_bits(nsec)); + + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, PTP_CMD_CTL, + PTP_CMD_CTL_PTP_CLOCK_LOAD_); } static void lan8814_ptp_clock_get(struct phy_device *phydev, - u32 *seconds, u32 *nano_seconds) + time64_t *sec, u32 *nsec) { - lanphy_write_page_reg(phydev, 4, PTP_CMD_CTL, PTP_CMD_CTL_PTP_CLOCK_READ_); - - *seconds = lanphy_read_page_reg(phydev, 4, PTP_CLOCK_READ_SEC_MID); - *seconds = (*seconds << 16) | - lanphy_read_page_reg(phydev, 4, PTP_CLOCK_READ_SEC_LO); - - *nano_seconds = lanphy_read_page_reg(phydev, 4, PTP_CLOCK_READ_NS_HI); - *nano_seconds = ((*nano_seconds & 0x3fff) << 16) | - lanphy_read_page_reg(phydev, 4, PTP_CLOCK_READ_NS_LO); + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, PTP_CMD_CTL, + PTP_CMD_CTL_PTP_CLOCK_READ_); + + *sec = lanphy_read_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_CLOCK_READ_SEC_HI); + *sec <<= 16; + *sec |= lanphy_read_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_CLOCK_READ_SEC_MID); + *sec <<= 16; + *sec |= lanphy_read_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_CLOCK_READ_SEC_LO); + + *nsec = lanphy_read_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_CLOCK_READ_NS_HI); + *nsec <<= 16; + *nsec |= lanphy_read_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_CLOCK_READ_NS_LO); } static int lan8814_ptpci_gettime64(struct ptp_clock_info *ptpci, @@ -2475,7 +3381,7 @@ static int lan8814_ptpci_gettime64(struct ptp_clock_info *ptpci, ptp_clock_info); struct phy_device *phydev = shared->phydev; u32 nano_seconds; - u32 seconds; + time64_t seconds; mutex_lock(&shared->shared_lock); lan8814_ptp_clock_get(phydev, &seconds, &nano_seconds); @@ -2500,43 +3406,71 @@ static int lan8814_ptpci_settime64(struct ptp_clock_info *ptpci, return 0; } +static void lan8814_ptp_set_target(struct phy_device *phydev, int event, + s64 start_sec, u32 start_nsec) +{ + /* Set the start time */ + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + LAN8814_PTP_CLOCK_TARGET_SEC_LO(event), + lower_16_bits(start_sec)); + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + LAN8814_PTP_CLOCK_TARGET_SEC_HI(event), + upper_16_bits(start_sec)); + + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + LAN8814_PTP_CLOCK_TARGET_NS_LO(event), + lower_16_bits(start_nsec)); + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + LAN8814_PTP_CLOCK_TARGET_NS_HI(event), + upper_16_bits(start_nsec) & 0x3fff); +} + +static void lan8814_ptp_update_target(struct phy_device *phydev, time64_t sec) +{ + lan8814_ptp_set_target(phydev, LAN8814_EVENT_A, + sec + LAN8814_BUFFER_TIME, 0); + lan8814_ptp_set_target(phydev, LAN8814_EVENT_B, + sec + LAN8814_BUFFER_TIME, 0); +} + static void lan8814_ptp_clock_step(struct phy_device *phydev, s64 time_step_ns) { u32 nano_seconds_step; u64 abs_time_step_ns; - u32 unsigned_seconds; + time64_t set_seconds; u32 nano_seconds; u32 remainder; s32 seconds; if (time_step_ns > 15000000000LL) { /* convert to clock set */ - lan8814_ptp_clock_get(phydev, &unsigned_seconds, &nano_seconds); - unsigned_seconds += div_u64_rem(time_step_ns, 1000000000LL, - &remainder); + lan8814_ptp_clock_get(phydev, &set_seconds, &nano_seconds); + set_seconds += div_u64_rem(time_step_ns, 1000000000LL, + &remainder); nano_seconds += remainder; if (nano_seconds >= 1000000000) { - unsigned_seconds++; + set_seconds++; nano_seconds -= 1000000000; } - lan8814_ptp_clock_set(phydev, unsigned_seconds, nano_seconds); + lan8814_ptp_clock_set(phydev, set_seconds, nano_seconds); + lan8814_ptp_update_target(phydev, set_seconds); return; } else if (time_step_ns < -15000000000LL) { /* convert to clock set */ time_step_ns = -time_step_ns; - lan8814_ptp_clock_get(phydev, &unsigned_seconds, &nano_seconds); - unsigned_seconds -= div_u64_rem(time_step_ns, 1000000000LL, - &remainder); + lan8814_ptp_clock_get(phydev, &set_seconds, &nano_seconds); + set_seconds -= div_u64_rem(time_step_ns, 1000000000LL, + &remainder); nano_seconds_step = remainder; if (nano_seconds < nano_seconds_step) { - unsigned_seconds--; + set_seconds--; nano_seconds += 1000000000; } nano_seconds -= nano_seconds_step; - lan8814_ptp_clock_set(phydev, unsigned_seconds, - nano_seconds); + lan8814_ptp_clock_set(phydev, set_seconds, nano_seconds); + lan8814_ptp_update_target(phydev, set_seconds); return; } @@ -2573,6 +3507,8 @@ static void lan8814_ptp_clock_step(struct phy_device *phydev, } while (seconds) { + u32 nsec; + if (seconds > 0) { u32 adjustment_value = (u32)seconds; u16 adjustment_value_lo, adjustment_value_hi; @@ -2583,12 +3519,18 @@ static void lan8814_ptp_clock_step(struct phy_device *phydev, adjustment_value_lo = adjustment_value & 0xffff; adjustment_value_hi = (adjustment_value >> 16) & 0x3fff; - lanphy_write_page_reg(phydev, 4, PTP_LTC_STEP_ADJ_LO, + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_LTC_STEP_ADJ_LO, adjustment_value_lo); - lanphy_write_page_reg(phydev, 4, PTP_LTC_STEP_ADJ_HI, + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_LTC_STEP_ADJ_HI, PTP_LTC_STEP_ADJ_DIR_ | adjustment_value_hi); seconds -= ((s32)adjustment_value); + + lan8814_ptp_clock_get(phydev, &set_seconds, &nsec); + set_seconds -= adjustment_value; + lan8814_ptp_update_target(phydev, set_seconds); } else { u32 adjustment_value = (u32)(-seconds); u16 adjustment_value_lo, adjustment_value_hi; @@ -2599,14 +3541,20 @@ static void lan8814_ptp_clock_step(struct phy_device *phydev, adjustment_value_lo = adjustment_value & 0xffff; adjustment_value_hi = (adjustment_value >> 16) & 0x3fff; - lanphy_write_page_reg(phydev, 4, PTP_LTC_STEP_ADJ_LO, + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_LTC_STEP_ADJ_LO, adjustment_value_lo); - lanphy_write_page_reg(phydev, 4, PTP_LTC_STEP_ADJ_HI, + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_LTC_STEP_ADJ_HI, adjustment_value_hi); seconds += ((s32)adjustment_value); + + lan8814_ptp_clock_get(phydev, &set_seconds, &nsec); + set_seconds += adjustment_value; + lan8814_ptp_update_target(phydev, set_seconds); } - lanphy_write_page_reg(phydev, 4, PTP_CMD_CTL, - PTP_CMD_CTL_PTP_LTC_STEP_SEC_); + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_CMD_CTL, PTP_CMD_CTL_PTP_LTC_STEP_SEC_); } if (nano_seconds) { u16 nano_seconds_lo; @@ -2615,12 +3563,14 @@ static void lan8814_ptp_clock_step(struct phy_device *phydev, nano_seconds_lo = nano_seconds & 0xffff; nano_seconds_hi = (nano_seconds >> 16) & 0x3fff; - lanphy_write_page_reg(phydev, 4, PTP_LTC_STEP_ADJ_LO, + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_LTC_STEP_ADJ_LO, nano_seconds_lo); - lanphy_write_page_reg(phydev, 4, PTP_LTC_STEP_ADJ_HI, + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_LTC_STEP_ADJ_HI, PTP_LTC_STEP_ADJ_DIR_ | nano_seconds_hi); - lanphy_write_page_reg(phydev, 4, PTP_CMD_CTL, + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, PTP_CMD_CTL, PTP_CMD_CTL_PTP_LTC_STEP_NSEC_); } } @@ -2662,14 +3612,338 @@ static int lan8814_ptpci_adjfine(struct ptp_clock_info *ptpci, long scaled_ppm) kszphy_rate_adj_hi |= PTP_CLOCK_RATE_ADJ_DIR_; mutex_lock(&shared->shared_lock); - lanphy_write_page_reg(phydev, 4, PTP_CLOCK_RATE_ADJ_HI, kszphy_rate_adj_hi); - lanphy_write_page_reg(phydev, 4, PTP_CLOCK_RATE_ADJ_LO, kszphy_rate_adj_lo); + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, PTP_CLOCK_RATE_ADJ_HI, + kszphy_rate_adj_hi); + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, PTP_CLOCK_RATE_ADJ_LO, + kszphy_rate_adj_lo); mutex_unlock(&shared->shared_lock); return 0; } -static void lan8814_get_sig_tx(struct sk_buff *skb, u16 *sig) +static void lan8814_ptp_set_reload(struct phy_device *phydev, int event, + s64 period_sec, u32 period_nsec) +{ + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + LAN8814_PTP_CLOCK_TARGET_RELOAD_SEC_LO(event), + lower_16_bits(period_sec)); + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + LAN8814_PTP_CLOCK_TARGET_RELOAD_SEC_HI(event), + upper_16_bits(period_sec)); + + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + LAN8814_PTP_CLOCK_TARGET_RELOAD_NS_LO(event), + lower_16_bits(period_nsec)); + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + LAN8814_PTP_CLOCK_TARGET_RELOAD_NS_HI(event), + upper_16_bits(period_nsec) & 0x3fff); +} + +static void lan8814_ptp_enable_event(struct phy_device *phydev, int event, + int pulse_width) +{ + /* Set the pulse width of the event, + * Make sure that the target clock will be incremented each time when + * local time reaches or pass it + * Set the polarity high + */ + lanphy_modify_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, LAN8814_PTP_GENERAL_CONFIG, + LAN8814_PTP_GENERAL_CONFIG_LTC_EVENT_MASK(event) | + LAN8814_PTP_GENERAL_CONFIG_LTC_EVENT_SET(event, pulse_width) | + LAN8814_PTP_GENERAL_CONFIG_RELOAD_ADD_X(event) | + LAN8814_PTP_GENERAL_CONFIG_POLARITY_X(event), + LAN8814_PTP_GENERAL_CONFIG_LTC_EVENT_SET(event, pulse_width) | + LAN8814_PTP_GENERAL_CONFIG_POLARITY_X(event)); +} + +static void lan8814_ptp_disable_event(struct phy_device *phydev, int event) +{ + /* Set target to too far in the future, effectively disabling it */ + lan8814_ptp_set_target(phydev, event, 0xFFFFFFFF, 0); + + /* And then reload once it reaches the target */ + lanphy_modify_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, LAN8814_PTP_GENERAL_CONFIG, + LAN8814_PTP_GENERAL_CONFIG_RELOAD_ADD_X(event), + LAN8814_PTP_GENERAL_CONFIG_RELOAD_ADD_X(event)); +} + +static void lan8814_ptp_perout_off(struct phy_device *phydev, int pin) +{ + /* Disable gpio alternate function, + * 1: select as gpio, + * 0: select alt func + */ + lanphy_modify_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + LAN8814_GPIO_EN_ADDR(pin), + LAN8814_GPIO_EN_BIT(pin), + LAN8814_GPIO_EN_BIT(pin)); + + lanphy_modify_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + LAN8814_GPIO_DIR_ADDR(pin), + LAN8814_GPIO_DIR_BIT(pin), + 0); + + lanphy_modify_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + LAN8814_GPIO_BUF_ADDR(pin), + LAN8814_GPIO_BUF_BIT(pin), + 0); +} + +static void lan8814_ptp_perout_on(struct phy_device *phydev, int pin) +{ + /* Set as gpio output */ + lanphy_modify_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + LAN8814_GPIO_DIR_ADDR(pin), + LAN8814_GPIO_DIR_BIT(pin), + LAN8814_GPIO_DIR_BIT(pin)); + + /* Enable gpio 0:for alternate function, 1:gpio */ + lanphy_modify_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + LAN8814_GPIO_EN_ADDR(pin), + LAN8814_GPIO_EN_BIT(pin), + 0); + + /* Set buffer type to push pull */ + lanphy_modify_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + LAN8814_GPIO_BUF_ADDR(pin), + LAN8814_GPIO_BUF_BIT(pin), + LAN8814_GPIO_BUF_BIT(pin)); +} + +static int lan8814_ptp_perout(struct ptp_clock_info *ptpci, + struct ptp_clock_request *rq, int on) +{ + struct lan8814_shared_priv *shared = container_of(ptpci, struct lan8814_shared_priv, + ptp_clock_info); + struct phy_device *phydev = shared->phydev; + struct timespec64 ts_on, ts_period; + s64 on_nsec, period_nsec; + int pulse_width; + int pin, event; + + mutex_lock(&shared->shared_lock); + event = rq->perout.index; + pin = ptp_find_pin(shared->ptp_clock, PTP_PF_PEROUT, event); + if (pin < 0 || pin >= LAN8814_PTP_PEROUT_NUM) { + mutex_unlock(&shared->shared_lock); + return -EBUSY; + } + + if (!on) { + lan8814_ptp_perout_off(phydev, pin); + lan8814_ptp_disable_event(phydev, event); + mutex_unlock(&shared->shared_lock); + return 0; + } + + ts_on.tv_sec = rq->perout.on.sec; + ts_on.tv_nsec = rq->perout.on.nsec; + on_nsec = timespec64_to_ns(&ts_on); + + ts_period.tv_sec = rq->perout.period.sec; + ts_period.tv_nsec = rq->perout.period.nsec; + period_nsec = timespec64_to_ns(&ts_period); + + if (period_nsec < 200) { + pr_warn_ratelimited("%s: perout period too small, minimum is 200 nsec\n", + phydev_name(phydev)); + mutex_unlock(&shared->shared_lock); + return -EOPNOTSUPP; + } + + if (on_nsec >= period_nsec) { + pr_warn_ratelimited("%s: pulse width must be smaller than period\n", + phydev_name(phydev)); + mutex_unlock(&shared->shared_lock); + return -EINVAL; + } + + switch (on_nsec) { + case 200000000: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_200MS; + break; + case 100000000: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_100MS; + break; + case 50000000: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_50MS; + break; + case 10000000: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_10MS; + break; + case 5000000: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_5MS; + break; + case 1000000: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_1MS; + break; + case 500000: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_500US; + break; + case 100000: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_100US; + break; + case 50000: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_50US; + break; + case 10000: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_10US; + break; + case 5000: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_5US; + break; + case 1000: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_1US; + break; + case 500: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_500NS; + break; + case 100: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_100NS; + break; + default: + pr_warn_ratelimited("%s: Use default duty cycle of 100ns\n", + phydev_name(phydev)); + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_100NS; + break; + } + + /* Configure to pulse every period */ + lan8814_ptp_enable_event(phydev, event, pulse_width); + lan8814_ptp_set_target(phydev, event, rq->perout.start.sec, + rq->perout.start.nsec); + lan8814_ptp_set_reload(phydev, event, rq->perout.period.sec, + rq->perout.period.nsec); + lan8814_ptp_perout_on(phydev, pin); + mutex_unlock(&shared->shared_lock); + + return 0; +} + +static void lan8814_ptp_extts_on(struct phy_device *phydev, int pin, u32 flags) +{ + /* Set as gpio input */ + lanphy_modify_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + LAN8814_GPIO_DIR_ADDR(pin), + LAN8814_GPIO_DIR_BIT(pin), + 0); + + /* Map the pin to ltc pin 0 of the capture map registers */ + lanphy_modify_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_GPIO_CAP_MAP_LO, pin, pin); + + /* Enable capture on the edges of the ltc pin */ + if (flags & PTP_RISING_EDGE) + lanphy_modify_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_GPIO_CAP_EN, + PTP_GPIO_CAP_EN_GPIO_RE_CAPTURE_ENABLE(0), + PTP_GPIO_CAP_EN_GPIO_RE_CAPTURE_ENABLE(0)); + if (flags & PTP_FALLING_EDGE) + lanphy_modify_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_GPIO_CAP_EN, + PTP_GPIO_CAP_EN_GPIO_FE_CAPTURE_ENABLE(0), + PTP_GPIO_CAP_EN_GPIO_FE_CAPTURE_ENABLE(0)); + + /* Enable interrupt top interrupt */ + lanphy_modify_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, PTP_COMMON_INT_ENA, + PTP_COMMON_INT_ENA_GPIO_CAP_EN, + PTP_COMMON_INT_ENA_GPIO_CAP_EN); +} + +static void lan8814_ptp_extts_off(struct phy_device *phydev, int pin) +{ + /* Set as gpio out */ + lanphy_modify_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + LAN8814_GPIO_DIR_ADDR(pin), + LAN8814_GPIO_DIR_BIT(pin), + LAN8814_GPIO_DIR_BIT(pin)); + + /* Enable alternate, 0:for alternate function, 1:gpio */ + lanphy_modify_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + LAN8814_GPIO_EN_ADDR(pin), + LAN8814_GPIO_EN_BIT(pin), + 0); + + /* Clear the mapping of pin to registers 0 of the capture registers */ + lanphy_modify_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_GPIO_CAP_MAP_LO, + GENMASK(3, 0), + 0); + + /* Disable capture on both of the edges */ + lanphy_modify_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, PTP_GPIO_CAP_EN, + PTP_GPIO_CAP_EN_GPIO_RE_CAPTURE_ENABLE(pin) | + PTP_GPIO_CAP_EN_GPIO_FE_CAPTURE_ENABLE(pin), + 0); + + /* Disable interrupt top interrupt */ + lanphy_modify_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, PTP_COMMON_INT_ENA, + PTP_COMMON_INT_ENA_GPIO_CAP_EN, + 0); +} + +static int lan8814_ptp_extts(struct ptp_clock_info *ptpci, + struct ptp_clock_request *rq, int on) +{ + struct lan8814_shared_priv *shared = container_of(ptpci, struct lan8814_shared_priv, + ptp_clock_info); + struct phy_device *phydev = shared->phydev; + int pin; + + pin = ptp_find_pin(shared->ptp_clock, PTP_PF_EXTTS, + rq->extts.index); + if (pin == -1 || pin != LAN8814_PTP_EXTTS_NUM) + return -EINVAL; + + mutex_lock(&shared->shared_lock); + if (on) + lan8814_ptp_extts_on(phydev, pin, rq->extts.flags); + else + lan8814_ptp_extts_off(phydev, pin); + + mutex_unlock(&shared->shared_lock); + + return 0; +} + +static int lan8814_ptpci_enable(struct ptp_clock_info *ptpci, + struct ptp_clock_request *rq, int on) +{ + switch (rq->type) { + case PTP_CLK_REQ_PEROUT: + return lan8814_ptp_perout(ptpci, rq, on); + case PTP_CLK_REQ_EXTTS: + return lan8814_ptp_extts(ptpci, rq, on); + default: + return -EINVAL; + } +} + +static int lan8814_ptpci_verify(struct ptp_clock_info *ptp, unsigned int pin, + enum ptp_pin_function func, unsigned int chan) +{ + switch (func) { + case PTP_PF_NONE: + case PTP_PF_PEROUT: + /* Only pins 0 and 1 can generate perout signals. And for pin 0 + * there is only chan 0 (event A) and for pin 1 there is only + * chan 1 (event B) + */ + if (pin >= LAN8814_PTP_PEROUT_NUM || pin != chan) + return -1; + break; + case PTP_PF_EXTTS: + if (pin != LAN8814_PTP_EXTTS_NUM) + return -1; + break; + default: + return -1; + } + + return 0; +} + +static bool lan8814_get_sig_tx(struct sk_buff *skb, u16 *sig) { struct ptp_header *ptp_header; u32 type; @@ -2677,25 +3951,26 @@ static void lan8814_get_sig_tx(struct sk_buff *skb, u16 *sig) type = ptp_classify_raw(skb); ptp_header = ptp_parse_header(skb, type); + if (!ptp_header) + return false; + *sig = (__force u16)(ntohs(ptp_header->sequence_id)); + return true; } -static void lan8814_dequeue_tx_skb(struct kszphy_ptp_priv *ptp_priv) +static void lan8814_match_tx_skb(struct kszphy_ptp_priv *ptp_priv, + u32 seconds, u32 nsec, u16 seq_id) { - struct phy_device *phydev = ptp_priv->phydev; struct skb_shared_hwtstamps shhwtstamps; struct sk_buff *skb, *skb_tmp; unsigned long flags; - u32 seconds, nsec; bool ret = false; u16 skb_sig; - u16 seq_id; - - lan8814_ptp_tx_ts_get(phydev, &seconds, &nsec, &seq_id); spin_lock_irqsave(&ptp_priv->tx_queue.lock, flags); skb_queue_walk_safe(&ptp_priv->tx_queue, skb, skb_tmp) { - lan8814_get_sig_tx(skb, &skb_sig); + if (!lan8814_get_sig_tx(skb, &skb_sig)) + continue; if (memcmp(&skb_sig, &seq_id, sizeof(seq_id))) continue; @@ -2713,6 +3988,16 @@ static void lan8814_dequeue_tx_skb(struct kszphy_ptp_priv *ptp_priv) } } +static void lan8814_dequeue_tx_skb(struct kszphy_ptp_priv *ptp_priv) +{ + struct phy_device *phydev = ptp_priv->phydev; + u32 seconds, nsec; + u16 seq_id; + + lan8814_ptp_tx_ts_get(phydev, &seconds, &nsec, &seq_id); + lan8814_match_tx_skb(ptp_priv, seconds, nsec, seq_id); +} + static void lan8814_get_tx_ts(struct kszphy_ptp_priv *ptp_priv) { struct phy_device *phydev = ptp_priv->phydev; @@ -2724,7 +4009,8 @@ static void lan8814_get_tx_ts(struct kszphy_ptp_priv *ptp_priv) /* If other timestamps are available in the FIFO, * process them. */ - reg = lanphy_read_page_reg(phydev, 5, PTP_CAP_INFO); + reg = lanphy_read_page_reg(phydev, LAN8814_PAGE_PORT_REGS, + PTP_CAP_INFO); } while (PTP_CAP_INFO_TX_TS_CNT_GET_(reg) > 0); } @@ -2739,7 +4025,8 @@ static bool lan8814_match_skb(struct kszphy_ptp_priv *ptp_priv, spin_lock_irqsave(&ptp_priv->rx_queue.lock, flags); skb_queue_walk_safe(&ptp_priv->rx_queue, skb, skb_tmp) { - lan8814_get_sig_rx(skb, &skb_sig); + if (!lan8814_get_sig_rx(skb, &skb_sig)) + continue; if (memcmp(&skb_sig, &rx_ts->seq_id, sizeof(rx_ts->seq_id))) continue; @@ -2761,11 +4048,27 @@ static bool lan8814_match_skb(struct kszphy_ptp_priv *ptp_priv, return ret; } +static void lan8814_match_rx_ts(struct kszphy_ptp_priv *ptp_priv, + struct lan8814_ptp_rx_ts *rx_ts) +{ + unsigned long flags; + + /* If we failed to match the skb add it to the queue for when + * the frame will come + */ + if (!lan8814_match_skb(ptp_priv, rx_ts)) { + spin_lock_irqsave(&ptp_priv->rx_ts_lock, flags); + list_add(&rx_ts->list, &ptp_priv->rx_ts_list); + spin_unlock_irqrestore(&ptp_priv->rx_ts_lock, flags); + } else { + kfree(rx_ts); + } +} + static void lan8814_get_rx_ts(struct kszphy_ptp_priv *ptp_priv) { struct phy_device *phydev = ptp_priv->phydev; struct lan8814_ptp_rx_ts *rx_ts; - unsigned long flags; u32 reg; do { @@ -2775,32 +4078,21 @@ static void lan8814_get_rx_ts(struct kszphy_ptp_priv *ptp_priv) lan8814_ptp_rx_ts_get(phydev, &rx_ts->seconds, &rx_ts->nsec, &rx_ts->seq_id); - - /* If we failed to match the skb add it to the queue for when - * the frame will come - */ - if (!lan8814_match_skb(ptp_priv, rx_ts)) { - spin_lock_irqsave(&ptp_priv->rx_ts_lock, flags); - list_add(&rx_ts->list, &ptp_priv->rx_ts_list); - spin_unlock_irqrestore(&ptp_priv->rx_ts_lock, flags); - } else { - kfree(rx_ts); - } + lan8814_match_rx_ts(ptp_priv, rx_ts); /* If other timestamps are available in the FIFO, * process them. */ - reg = lanphy_read_page_reg(phydev, 5, PTP_CAP_INFO); + reg = lanphy_read_page_reg(phydev, LAN8814_PAGE_PORT_REGS, + PTP_CAP_INFO); } while (PTP_CAP_INFO_RX_TS_CNT_GET_(reg) > 0); } -static void lan8814_handle_ptp_interrupt(struct phy_device *phydev) +static void lan8814_handle_ptp_interrupt(struct phy_device *phydev, u16 status) { struct kszphy_priv *priv = phydev->priv; struct kszphy_ptp_priv *ptp_priv = &priv->ptp_priv; - u16 status; - status = lanphy_read_page_reg(phydev, 5, PTP_TSU_INT_STS); if (status & PTP_TSU_INT_STS_PTP_TX_TS_EN_) lan8814_get_tx_ts(ptp_priv); @@ -2818,21 +4110,86 @@ static void lan8814_handle_ptp_interrupt(struct phy_device *phydev) } } -static int lan8804_config_init(struct phy_device *phydev) +static int lan8814_gpio_process_cap(struct lan8814_shared_priv *shared) { - int val; + struct phy_device *phydev = shared->phydev; + struct ptp_clock_event ptp_event = {0}; + unsigned long nsec; + s64 sec; + u16 tmp; + + /* This is 0 because whatever was the input pin it was mapped it to + * ltc gpio pin 0 + */ + lanphy_modify_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, PTP_GPIO_SEL, + PTP_GPIO_SEL_GPIO_SEL(0), + PTP_GPIO_SEL_GPIO_SEL(0)); + + tmp = lanphy_read_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_GPIO_CAP_STS); + if (!(tmp & PTP_GPIO_CAP_STS_PTP_GPIO_RE_STS(0)) && + !(tmp & PTP_GPIO_CAP_STS_PTP_GPIO_FE_STS(0))) + return -1; + + if (tmp & BIT(0)) { + sec = lanphy_read_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_GPIO_RE_LTC_SEC_HI_CAP); + sec <<= 16; + sec |= lanphy_read_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_GPIO_RE_LTC_SEC_LO_CAP); + + nsec = lanphy_read_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_GPIO_RE_LTC_NS_HI_CAP) & 0x3fff; + nsec <<= 16; + nsec |= lanphy_read_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_GPIO_RE_LTC_NS_LO_CAP); + } else { + sec = lanphy_read_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_GPIO_FE_LTC_SEC_HI_CAP); + sec <<= 16; + sec |= lanphy_read_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_GPIO_FE_LTC_SEC_LO_CAP); + + nsec = lanphy_read_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_GPIO_FE_LTC_NS_HI_CAP) & 0x3fff; + nsec <<= 16; + nsec |= lanphy_read_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + PTP_GPIO_RE_LTC_NS_LO_CAP); + } + + ptp_event.index = 0; + ptp_event.timestamp = ktime_set(sec, nsec); + ptp_event.type = PTP_CLOCK_EXTTS; + ptp_clock_event(shared->ptp_clock, &ptp_event); + + return 0; +} + +static int lan8814_handle_gpio_interrupt(struct phy_device *phydev, u16 status) +{ + struct lan8814_shared_priv *shared = phy_package_get_priv(phydev); + int ret; + + mutex_lock(&shared->shared_lock); + ret = lan8814_gpio_process_cap(shared); + mutex_unlock(&shared->shared_lock); + + return ret; +} +static int lan8804_config_init(struct phy_device *phydev) +{ /* MDI-X setting for swap A,B transmit */ - val = lanphy_read_page_reg(phydev, 2, LAN8804_ALIGN_SWAP); - val &= ~LAN8804_ALIGN_TX_A_B_SWAP_MASK; - val |= LAN8804_ALIGN_TX_A_B_SWAP; - lanphy_write_page_reg(phydev, 2, LAN8804_ALIGN_SWAP, val); + lanphy_modify_page_reg(phydev, LAN8814_PAGE_PCS_DIGITAL, LAN8804_ALIGN_SWAP, + LAN8804_ALIGN_TX_A_B_SWAP_MASK, + LAN8804_ALIGN_TX_A_B_SWAP); /* Make sure that the PHY will not stop generating the clock when the * link partner goes down */ - lanphy_write_page_reg(phydev, 31, LAN8814_CLOCK_MANAGEMENT, 0x27e); - lanphy_read_page_reg(phydev, 1, LAN8814_LINK_QUALITY); + lanphy_write_page_reg(phydev, LAN8814_PAGE_SYSTEM_CTRL, + LAN8814_CLOCK_MANAGEMENT, 0x27e); + lanphy_read_page_reg(phydev, LAN8814_PAGE_AFE_PMA, LAN8814_LINK_QUALITY); return 0; } @@ -2897,10 +4254,21 @@ static int lan8804_config_intr(struct phy_device *phydev) return 0; } +/* Check if the PHY has 1588 support. There are multiple skus of the PHY and + * some of them support PTP while others don't support it. This function will + * return true is the sku supports it, otherwise will return false. + */ +static bool lan8814_has_ptp(struct phy_device *phydev) +{ + struct kszphy_priv *priv = phydev->priv; + + return priv->is_ptp_available; +} + static irqreturn_t lan8814_handle_interrupt(struct phy_device *phydev) { - int irq_status, tsu_irq_status; int ret = IRQ_NONE; + int irq_status; irq_status = phy_read(phydev, LAN8814_INTS); if (irq_status < 0) { @@ -2913,22 +4281,22 @@ static irqreturn_t lan8814_handle_interrupt(struct phy_device *phydev) ret = IRQ_HANDLED; } - while (1) { - tsu_irq_status = lanphy_read_page_reg(phydev, 4, - LAN8814_INTR_STS_REG); + if (!lan8814_has_ptp(phydev)) + return ret; - if (tsu_irq_status > 0 && - (tsu_irq_status & (LAN8814_INTR_STS_REG_1588_TSU0_ | - LAN8814_INTR_STS_REG_1588_TSU1_ | - LAN8814_INTR_STS_REG_1588_TSU2_ | - LAN8814_INTR_STS_REG_1588_TSU3_))) { - lan8814_handle_ptp_interrupt(phydev); - ret = IRQ_HANDLED; - } else { + while (true) { + irq_status = lanphy_read_page_reg(phydev, LAN8814_PAGE_PORT_REGS, + PTP_TSU_INT_STS); + if (!irq_status) break; - } + + lan8814_handle_ptp_interrupt(phydev, irq_status); + ret = IRQ_HANDLED; } + if (!lan8814_handle_gpio_interrupt(phydev, irq_status)) + ret = IRQ_HANDLED; + return ret; } @@ -2946,7 +4314,7 @@ static int lan8814_config_intr(struct phy_device *phydev) { int err; - lanphy_write_page_reg(phydev, 4, LAN8814_INTR_CTRL_REG, + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, LAN8814_INTR_CTRL_REG, LAN8814_INTR_CTRL_REG_POLARITY | LAN8814_INTR_CTRL_REG_INTR_ENABLE); @@ -2972,30 +4340,45 @@ static void lan8814_ptp_init(struct phy_device *phydev) { struct kszphy_priv *priv = phydev->priv; struct kszphy_ptp_priv *ptp_priv = &priv->ptp_priv; - u32 temp; if (!IS_ENABLED(CONFIG_PTP_1588_CLOCK) || !IS_ENABLED(CONFIG_NETWORK_PHY_TIMESTAMPING)) return; - lanphy_write_page_reg(phydev, 5, TSU_HARD_RESET, TSU_HARD_RESET_); + if (!lan8814_has_ptp(phydev)) + return; + + lanphy_write_page_reg(phydev, LAN8814_PAGE_PORT_REGS, + TSU_HARD_RESET, TSU_HARD_RESET_); - temp = lanphy_read_page_reg(phydev, 5, PTP_TX_MOD); - temp |= PTP_TX_MOD_BAD_UDPV4_CHKSUM_FORCE_FCS_DIS_; - lanphy_write_page_reg(phydev, 5, PTP_TX_MOD, temp); + lanphy_modify_page_reg(phydev, LAN8814_PAGE_PORT_REGS, PTP_TX_MOD, + PTP_TX_MOD_BAD_UDPV4_CHKSUM_FORCE_FCS_DIS_, + PTP_TX_MOD_BAD_UDPV4_CHKSUM_FORCE_FCS_DIS_); - temp = lanphy_read_page_reg(phydev, 5, PTP_RX_MOD); - temp |= PTP_RX_MOD_BAD_UDPV4_CHKSUM_FORCE_FCS_DIS_; - lanphy_write_page_reg(phydev, 5, PTP_RX_MOD, temp); + lanphy_modify_page_reg(phydev, LAN8814_PAGE_PORT_REGS, PTP_RX_MOD, + PTP_RX_MOD_BAD_UDPV4_CHKSUM_FORCE_FCS_DIS_, + PTP_RX_MOD_BAD_UDPV4_CHKSUM_FORCE_FCS_DIS_); - lanphy_write_page_reg(phydev, 5, PTP_RX_PARSE_CONFIG, 0); - lanphy_write_page_reg(phydev, 5, PTP_TX_PARSE_CONFIG, 0); + lanphy_write_page_reg(phydev, LAN8814_PAGE_PORT_REGS, + PTP_RX_PARSE_CONFIG, 0); + lanphy_write_page_reg(phydev, LAN8814_PAGE_PORT_REGS, + PTP_TX_PARSE_CONFIG, 0); /* Removing default registers configs related to L2 and IP */ - lanphy_write_page_reg(phydev, 5, PTP_TX_PARSE_L2_ADDR_EN, 0); - lanphy_write_page_reg(phydev, 5, PTP_RX_PARSE_L2_ADDR_EN, 0); - lanphy_write_page_reg(phydev, 5, PTP_TX_PARSE_IP_ADDR_EN, 0); - lanphy_write_page_reg(phydev, 5, PTP_RX_PARSE_IP_ADDR_EN, 0); + lanphy_write_page_reg(phydev, LAN8814_PAGE_PORT_REGS, + PTP_TX_PARSE_L2_ADDR_EN, 0); + lanphy_write_page_reg(phydev, LAN8814_PAGE_PORT_REGS, + PTP_RX_PARSE_L2_ADDR_EN, 0); + lanphy_write_page_reg(phydev, LAN8814_PAGE_PORT_REGS, + PTP_TX_PARSE_IP_ADDR_EN, 0); + lanphy_write_page_reg(phydev, LAN8814_PAGE_PORT_REGS, + PTP_RX_PARSE_IP_ADDR_EN, 0); + + /* Disable checking for minorVersionPTP field */ + lanphy_write_page_reg(phydev, LAN8814_PAGE_PORT_REGS, PTP_RX_VERSION, + PTP_MAX_VERSION(0xff) | PTP_MIN_VERSION(0x0)); + lanphy_write_page_reg(phydev, LAN8814_PAGE_PORT_REGS, PTP_TX_VERSION, + PTP_MAX_VERSION(0xff) | PTP_MIN_VERSION(0x0)); skb_queue_head_init(&ptp_priv->tx_queue); skb_queue_head_init(&ptp_priv->rx_queue); @@ -3006,93 +4389,143 @@ static void lan8814_ptp_init(struct phy_device *phydev) ptp_priv->mii_ts.rxtstamp = lan8814_rxtstamp; ptp_priv->mii_ts.txtstamp = lan8814_txtstamp; - ptp_priv->mii_ts.hwtstamp = lan8814_hwtstamp; + ptp_priv->mii_ts.hwtstamp_set = lan8814_hwtstamp_set; ptp_priv->mii_ts.ts_info = lan8814_ts_info; phydev->mii_ts = &ptp_priv->mii_ts; + + /* Timestamp selected by default to keep legacy API */ + phydev->default_timestamp = true; } -static int lan8814_ptp_probe_once(struct phy_device *phydev) +static int __lan8814_ptp_probe_once(struct phy_device *phydev, char *pin_name, + int gpios) { - struct lan8814_shared_priv *shared = phydev->shared->priv; + struct lan8814_shared_priv *shared = phy_package_get_priv(phydev); - if (!IS_ENABLED(CONFIG_PTP_1588_CLOCK) || - !IS_ENABLED(CONFIG_NETWORK_PHY_TIMESTAMPING)) - return 0; + shared->phydev = phydev; /* Initialise shared lock for clock*/ mutex_init(&shared->shared_lock); + shared->pin_config = devm_kmalloc_array(&phydev->mdio.dev, + gpios, + sizeof(*shared->pin_config), + GFP_KERNEL); + if (!shared->pin_config) + return -ENOMEM; + + for (int i = 0; i < gpios; i++) { + struct ptp_pin_desc *ptp_pin = &shared->pin_config[i]; + + memset(ptp_pin, 0, sizeof(*ptp_pin)); + snprintf(ptp_pin->name, + sizeof(ptp_pin->name), "%s_%02d", pin_name, i); + ptp_pin->index = i; + ptp_pin->func = PTP_PF_NONE; + } + shared->ptp_clock_info.owner = THIS_MODULE; snprintf(shared->ptp_clock_info.name, 30, "%s", phydev->drv->name); shared->ptp_clock_info.max_adj = 31249999; shared->ptp_clock_info.n_alarm = 0; - shared->ptp_clock_info.n_ext_ts = 0; - shared->ptp_clock_info.n_pins = 0; + shared->ptp_clock_info.n_ext_ts = LAN8814_PTP_EXTTS_NUM; + shared->ptp_clock_info.n_pins = gpios; shared->ptp_clock_info.pps = 0; - shared->ptp_clock_info.pin_config = NULL; + shared->ptp_clock_info.supported_extts_flags = PTP_RISING_EDGE | + PTP_FALLING_EDGE | + PTP_STRICT_FLAGS; + shared->ptp_clock_info.supported_perout_flags = PTP_PEROUT_DUTY_CYCLE; + shared->ptp_clock_info.pin_config = shared->pin_config; + shared->ptp_clock_info.n_per_out = LAN8814_PTP_PEROUT_NUM; shared->ptp_clock_info.adjfine = lan8814_ptpci_adjfine; shared->ptp_clock_info.adjtime = lan8814_ptpci_adjtime; shared->ptp_clock_info.gettime64 = lan8814_ptpci_gettime64; shared->ptp_clock_info.settime64 = lan8814_ptpci_settime64; shared->ptp_clock_info.getcrosststamp = NULL; + shared->ptp_clock_info.enable = lan8814_ptpci_enable; + shared->ptp_clock_info.verify = lan8814_ptpci_verify; shared->ptp_clock = ptp_clock_register(&shared->ptp_clock_info, &phydev->mdio.dev); - if (IS_ERR_OR_NULL(shared->ptp_clock)) { - phydev_err(phydev, "ptp_clock_register failed %lu\n", - PTR_ERR(shared->ptp_clock)); + if (IS_ERR(shared->ptp_clock)) { + phydev_err(phydev, "ptp_clock_register failed %pe\n", + shared->ptp_clock); return -EINVAL; } - phydev_dbg(phydev, "successfully registered ptp clock\n"); + /* Check if PHC support is missing at the configuration level */ + if (!shared->ptp_clock) + return 0; - shared->phydev = phydev; + phydev_dbg(phydev, "successfully registered ptp clock\n"); /* The EP.4 is shared between all the PHYs in the package and also it * can be accessed by any of the PHYs */ - lanphy_write_page_reg(phydev, 4, LTC_HARD_RESET, LTC_HARD_RESET_); - lanphy_write_page_reg(phydev, 4, PTP_OPERATING_MODE, + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + LTC_HARD_RESET, LTC_HARD_RESET_); + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, PTP_OPERATING_MODE, PTP_OPERATING_MODE_STANDALONE_); + /* Enable ptp to run LTC clock for ptp and gpio 1PPS operation */ + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, PTP_CMD_CTL, + PTP_CMD_CTL_PTP_ENABLE_); + return 0; } +static int lan8814_ptp_probe_once(struct phy_device *phydev) +{ + if (!lan8814_has_ptp(phydev)) + return 0; + + return __lan8814_ptp_probe_once(phydev, "lan8814_ptp_pin", + LAN8814_PTP_GPIO_NUM); +} + static void lan8814_setup_led(struct phy_device *phydev, int val) { int temp; - temp = lanphy_read_page_reg(phydev, 5, LAN8814_LED_CTRL_1); + temp = lanphy_read_page_reg(phydev, LAN8814_PAGE_PORT_REGS, + LAN8814_LED_CTRL_1); if (val) temp |= LAN8814_LED_CTRL_1_KSZ9031_LED_MODE_; else temp &= ~LAN8814_LED_CTRL_1_KSZ9031_LED_MODE_; - lanphy_write_page_reg(phydev, 5, LAN8814_LED_CTRL_1, temp); + lanphy_write_page_reg(phydev, LAN8814_PAGE_PORT_REGS, + LAN8814_LED_CTRL_1, temp); } static int lan8814_config_init(struct phy_device *phydev) { struct kszphy_priv *lan8814 = phydev->priv; - int val; + int ret; - /* Reset the PHY */ - val = lanphy_read_page_reg(phydev, 4, LAN8814_QSGMII_SOFT_RESET); - val |= LAN8814_QSGMII_SOFT_RESET_BIT; - lanphy_write_page_reg(phydev, 4, LAN8814_QSGMII_SOFT_RESET, val); + /* Based on the interface type select how the advertise ability is + * encoded, to set as SGMII or as USGMII. + */ + if (phydev->interface == PHY_INTERFACE_MODE_QSGMII) + ret = lanphy_modify_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + LAN8814_QSGMII_TX_CONFIG, + LAN8814_QSGMII_TX_CONFIG_QSGMII, + LAN8814_QSGMII_TX_CONFIG_QSGMII); + else + ret = lanphy_modify_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + LAN8814_QSGMII_TX_CONFIG, + LAN8814_QSGMII_TX_CONFIG_QSGMII, + 0); - /* Disable ANEG with QSGMII PCS Host side */ - val = lanphy_read_page_reg(phydev, 5, LAN8814_QSGMII_PCS1G_ANEG_CONFIG); - val &= ~LAN8814_QSGMII_PCS1G_ANEG_CONFIG_ANEG_ENA; - lanphy_write_page_reg(phydev, 5, LAN8814_QSGMII_PCS1G_ANEG_CONFIG, val); + if (ret < 0) + return ret; /* MDI-X setting for swap A,B transmit */ - val = lanphy_read_page_reg(phydev, 2, LAN8814_ALIGN_SWAP); - val &= ~LAN8814_ALIGN_TX_A_B_SWAP_MASK; - val |= LAN8814_ALIGN_TX_A_B_SWAP; - lanphy_write_page_reg(phydev, 2, LAN8814_ALIGN_SWAP, val); + lanphy_modify_page_reg(phydev, LAN8814_PAGE_PCS_DIGITAL, LAN8814_ALIGN_SWAP, + LAN8814_ALIGN_TX_A_B_SWAP_MASK, + LAN8814_ALIGN_TX_A_B_SWAP); if (lan8814->led_mode >= 0) lan8814_setup_led(phydev, lan8814->led_mode); @@ -3121,6 +4554,28 @@ static int lan8814_release_coma_mode(struct phy_device *phydev) return 0; } +static void lan8814_clear_2psp_bit(struct phy_device *phydev) +{ + /* It was noticed that when traffic is passing through the PHY and the + * cable is removed then the LED was still on even though there is no + * link + */ + lanphy_modify_page_reg(phydev, LAN8814_PAGE_PCS_DIGITAL, LAN8814_EEE_STATE, + LAN8814_EEE_STATE_MASK2P5P, + 0); +} + +static void lan8814_update_meas_time(struct phy_device *phydev) +{ + /* By setting the measure time to a value of 0xb this will allow cables + * longer than 100m to be used. This configuration can be used + * regardless of the mode of operation of the PHY + */ + lanphy_modify_page_reg(phydev, LAN8814_PAGE_AFE_PMA, LAN8814_PD_CONTROLS, + LAN8814_PD_CONTROLS_PD_MEAS_TIME_MASK, + LAN8814_PD_CONTROLS_PD_MEAS_TIME_VAL); +} + static int lan8814_probe(struct phy_device *phydev) { const struct kszphy_type *type = phydev->drv->driver_data; @@ -3141,11 +4596,29 @@ static int lan8814_probe(struct phy_device *phydev) /* Strap-in value for PHY address, below register read gives starting * phy address value */ - addr = lanphy_read_page_reg(phydev, 4, 0) & 0x1F; + addr = lanphy_read_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, 0) & 0x1F; devm_phy_package_join(&phydev->mdio.dev, phydev, addr, sizeof(struct lan8814_shared_priv)); + /* There are lan8814 SKUs that don't support PTP. Make sure that for + * those skus no PTP device is created. Here we check if the SKU + * supports PTP. + */ + err = lanphy_read_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + LAN8814_SKUS); + if (err < 0) + return err; + + priv->is_ptp_available = err == LAN8814_REV_LAN8814 || + err == LAN8814_REV_LAN8818; + if (phy_package_init_once(phydev)) { + /* Reset the PHY */ + lanphy_modify_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + LAN8814_QSGMII_SOFT_RESET, + LAN8814_QSGMII_SOFT_RESET_BIT, + LAN8814_QSGMII_SOFT_RESET_BIT); + err = lan8814_release_coma_mode(phydev); if (err) return err; @@ -3157,13 +4630,1849 @@ static int lan8814_probe(struct phy_device *phydev) lan8814_ptp_init(phydev); + /* Errata workarounds */ + lan8814_clear_2psp_bit(phydev); + lan8814_update_meas_time(phydev); + + return 0; +} + +#define LAN8841_MMD_TIMER_REG 0 +#define LAN8841_MMD0_REGISTER_17 17 +#define LAN8841_MMD0_REGISTER_17_DROP_OPT(x) ((x) & 0x3) +#define LAN8841_MMD0_REGISTER_17_XMIT_TOG_TX_DIS BIT(3) +#define LAN8841_OPERATION_MODE_STRAP_OVERRIDE_LOW_REG 2 +#define LAN8841_OPERATION_MODE_STRAP_OVERRIDE_LOW_REG_MAGJACK BIT(14) +#define LAN8841_MMD_ANALOG_REG 28 +#define LAN8841_ANALOG_CONTROL_1 1 +#define LAN8841_ANALOG_CONTROL_1_PLL_TRIM(x) (((x) & 0x3) << 5) +#define LAN8841_ANALOG_CONTROL_10 13 +#define LAN8841_ANALOG_CONTROL_10_PLL_DIV(x) ((x) & 0x3) +#define LAN8841_ANALOG_CONTROL_11 14 +#define LAN8841_ANALOG_CONTROL_11_LDO_REF(x) (((x) & 0x7) << 12) +#define LAN8841_TX_LOW_I_CH_C_D_POWER_MANAGMENT 69 +#define LAN8841_TX_LOW_I_CH_C_D_POWER_MANAGMENT_VAL 0xbffc +#define LAN8841_BTRX_POWER_DOWN 70 +#define LAN8841_BTRX_POWER_DOWN_QBIAS_CH_A BIT(0) +#define LAN8841_BTRX_POWER_DOWN_BTRX_CH_A BIT(1) +#define LAN8841_BTRX_POWER_DOWN_QBIAS_CH_B BIT(2) +#define LAN8841_BTRX_POWER_DOWN_BTRX_CH_B BIT(3) +#define LAN8841_BTRX_POWER_DOWN_BTRX_CH_C BIT(5) +#define LAN8841_BTRX_POWER_DOWN_BTRX_CH_D BIT(7) +#define LAN8841_ADC_CHANNEL_MASK 198 +#define LAN8841_PTP_RX_PARSE_L2_ADDR_EN 370 +#define LAN8841_PTP_RX_PARSE_IP_ADDR_EN 371 +#define LAN8841_PTP_RX_VERSION 374 +#define LAN8841_PTP_TX_PARSE_L2_ADDR_EN 434 +#define LAN8841_PTP_TX_PARSE_IP_ADDR_EN 435 +#define LAN8841_PTP_TX_VERSION 438 +#define LAN8841_PTP_CMD_CTL 256 +#define LAN8841_PTP_CMD_CTL_PTP_ENABLE BIT(2) +#define LAN8841_PTP_CMD_CTL_PTP_DISABLE BIT(1) +#define LAN8841_PTP_CMD_CTL_PTP_RESET BIT(0) +#define LAN8841_PTP_RX_PARSE_CONFIG 368 +#define LAN8841_PTP_TX_PARSE_CONFIG 432 +#define LAN8841_PTP_RX_MODE 381 +#define LAN8841_PTP_INSERT_TS_EN BIT(0) +#define LAN8841_PTP_INSERT_TS_32BIT BIT(1) + +static int lan8841_config_init(struct phy_device *phydev) +{ + int ret; + + ret = ksz9131_config_init(phydev); + if (ret) + return ret; + + /* Initialize the HW by resetting everything */ + phy_modify_mmd(phydev, KSZ9131RN_MMD_COMMON_CTRL_REG, + LAN8841_PTP_CMD_CTL, + LAN8841_PTP_CMD_CTL_PTP_RESET, + LAN8841_PTP_CMD_CTL_PTP_RESET); + + phy_modify_mmd(phydev, KSZ9131RN_MMD_COMMON_CTRL_REG, + LAN8841_PTP_CMD_CTL, + LAN8841_PTP_CMD_CTL_PTP_ENABLE, + LAN8841_PTP_CMD_CTL_PTP_ENABLE); + + /* Don't process any frames */ + phy_write_mmd(phydev, KSZ9131RN_MMD_COMMON_CTRL_REG, + LAN8841_PTP_RX_PARSE_CONFIG, 0); + phy_write_mmd(phydev, KSZ9131RN_MMD_COMMON_CTRL_REG, + LAN8841_PTP_TX_PARSE_CONFIG, 0); + phy_write_mmd(phydev, KSZ9131RN_MMD_COMMON_CTRL_REG, + LAN8841_PTP_TX_PARSE_L2_ADDR_EN, 0); + phy_write_mmd(phydev, KSZ9131RN_MMD_COMMON_CTRL_REG, + LAN8841_PTP_RX_PARSE_L2_ADDR_EN, 0); + phy_write_mmd(phydev, KSZ9131RN_MMD_COMMON_CTRL_REG, + LAN8841_PTP_TX_PARSE_IP_ADDR_EN, 0); + phy_write_mmd(phydev, KSZ9131RN_MMD_COMMON_CTRL_REG, + LAN8841_PTP_RX_PARSE_IP_ADDR_EN, 0); + + /* Disable checking for minorVersionPTP field */ + phy_write_mmd(phydev, KSZ9131RN_MMD_COMMON_CTRL_REG, + LAN8841_PTP_RX_VERSION, 0xff00); + phy_write_mmd(phydev, KSZ9131RN_MMD_COMMON_CTRL_REG, + LAN8841_PTP_TX_VERSION, 0xff00); + + /* 100BT Clause 40 improvement errata */ + phy_write_mmd(phydev, LAN8841_MMD_ANALOG_REG, + LAN8841_ANALOG_CONTROL_1, + LAN8841_ANALOG_CONTROL_1_PLL_TRIM(0x2)); + phy_write_mmd(phydev, LAN8841_MMD_ANALOG_REG, + LAN8841_ANALOG_CONTROL_10, + LAN8841_ANALOG_CONTROL_10_PLL_DIV(0x1)); + + /* 10M/100M Ethernet Signal Tuning Errata for Shorted-Center Tap + * Magnetics + */ + ret = phy_read_mmd(phydev, KSZ9131RN_MMD_COMMON_CTRL_REG, + LAN8841_OPERATION_MODE_STRAP_OVERRIDE_LOW_REG); + if (ret & LAN8841_OPERATION_MODE_STRAP_OVERRIDE_LOW_REG_MAGJACK) { + phy_write_mmd(phydev, LAN8841_MMD_ANALOG_REG, + LAN8841_TX_LOW_I_CH_C_D_POWER_MANAGMENT, + LAN8841_TX_LOW_I_CH_C_D_POWER_MANAGMENT_VAL); + phy_write_mmd(phydev, LAN8841_MMD_ANALOG_REG, + LAN8841_BTRX_POWER_DOWN, + LAN8841_BTRX_POWER_DOWN_QBIAS_CH_A | + LAN8841_BTRX_POWER_DOWN_BTRX_CH_A | + LAN8841_BTRX_POWER_DOWN_QBIAS_CH_B | + LAN8841_BTRX_POWER_DOWN_BTRX_CH_B | + LAN8841_BTRX_POWER_DOWN_BTRX_CH_C | + LAN8841_BTRX_POWER_DOWN_BTRX_CH_D); + } + + /* LDO Adjustment errata */ + phy_write_mmd(phydev, LAN8841_MMD_ANALOG_REG, + LAN8841_ANALOG_CONTROL_11, + LAN8841_ANALOG_CONTROL_11_LDO_REF(1)); + + /* 100BT RGMII latency tuning errata */ + phy_write_mmd(phydev, MDIO_MMD_PMAPMD, + LAN8841_ADC_CHANNEL_MASK, 0x0); + phy_write_mmd(phydev, LAN8841_MMD_TIMER_REG, + LAN8841_MMD0_REGISTER_17, + LAN8841_MMD0_REGISTER_17_DROP_OPT(2) | + LAN8841_MMD0_REGISTER_17_XMIT_TOG_TX_DIS); + + return 0; +} + +#define LAN8841_OUTPUT_CTRL 25 +#define LAN8841_OUTPUT_CTRL_INT_BUFFER BIT(14) +#define LAN8841_INT_PTP BIT(9) + +static int lan8841_config_intr(struct phy_device *phydev) +{ + int err; + + phy_modify(phydev, LAN8841_OUTPUT_CTRL, + LAN8841_OUTPUT_CTRL_INT_BUFFER, 0); + + if (phydev->interrupts == PHY_INTERRUPT_ENABLED) { + err = phy_read(phydev, LAN8814_INTS); + if (err < 0) + return err; + + /* Enable / disable interrupts. It is OK to enable PTP interrupt + * even if it PTP is not enabled. Because the underneath blocks + * will not enable the PTP so we will never get the PTP + * interrupt. + */ + err = phy_write(phydev, LAN8814_INTC, + LAN8814_INT_LINK | LAN8841_INT_PTP); + } else { + err = phy_write(phydev, LAN8814_INTC, 0); + if (err) + return err; + + err = phy_read(phydev, LAN8814_INTS); + if (err < 0) + return err; + + /* Getting a positive value doesn't mean that is an error, it + * just indicates what was the status. Therefore make sure to + * clear the value and say that there is no error. + */ + err = 0; + } + + return err; +} + +#define LAN8841_PTP_TX_EGRESS_SEC_LO 453 +#define LAN8841_PTP_TX_EGRESS_SEC_HI 452 +#define LAN8841_PTP_TX_EGRESS_NS_LO 451 +#define LAN8841_PTP_TX_EGRESS_NS_HI 450 +#define LAN8841_PTP_TX_EGRESS_NSEC_HI_VALID BIT(15) +#define LAN8841_PTP_TX_MSG_HEADER2 455 + +static bool lan8841_ptp_get_tx_ts(struct kszphy_ptp_priv *ptp_priv, + u32 *sec, u32 *nsec, u16 *seq) +{ + struct phy_device *phydev = ptp_priv->phydev; + + *nsec = phy_read_mmd(phydev, 2, LAN8841_PTP_TX_EGRESS_NS_HI); + if (!(*nsec & LAN8841_PTP_TX_EGRESS_NSEC_HI_VALID)) + return false; + + *nsec = ((*nsec & 0x3fff) << 16); + *nsec = *nsec | phy_read_mmd(phydev, 2, LAN8841_PTP_TX_EGRESS_NS_LO); + + *sec = phy_read_mmd(phydev, 2, LAN8841_PTP_TX_EGRESS_SEC_HI); + *sec = *sec << 16; + *sec = *sec | phy_read_mmd(phydev, 2, LAN8841_PTP_TX_EGRESS_SEC_LO); + + *seq = phy_read_mmd(phydev, 2, LAN8841_PTP_TX_MSG_HEADER2); + + return true; +} + +static void lan8841_ptp_process_tx_ts(struct kszphy_ptp_priv *ptp_priv) +{ + u32 sec, nsec; + u16 seq; + + while (lan8841_ptp_get_tx_ts(ptp_priv, &sec, &nsec, &seq)) + lan8814_match_tx_skb(ptp_priv, sec, nsec, seq); +} + +#define LAN8841_PTP_INT_STS 259 +#define LAN8841_PTP_INT_STS_PTP_TX_TS_OVRFL_INT BIT(13) +#define LAN8841_PTP_INT_STS_PTP_TX_TS_INT BIT(12) +#define LAN8841_PTP_INT_STS_PTP_GPIO_CAP_INT BIT(2) + +static void lan8841_ptp_flush_fifo(struct kszphy_ptp_priv *ptp_priv) +{ + struct phy_device *phydev = ptp_priv->phydev; + int i; + + for (i = 0; i < FIFO_SIZE; ++i) + phy_read_mmd(phydev, 2, LAN8841_PTP_TX_MSG_HEADER2); + + phy_read_mmd(phydev, 2, LAN8841_PTP_INT_STS); +} + +#define LAN8841_PTP_GPIO_CAP_STS 506 +#define LAN8841_PTP_GPIO_SEL 327 +#define LAN8841_PTP_GPIO_SEL_GPIO_SEL(gpio) ((gpio) << 8) +#define LAN8841_PTP_GPIO_RE_LTC_SEC_HI_CAP 498 +#define LAN8841_PTP_GPIO_RE_LTC_SEC_LO_CAP 499 +#define LAN8841_PTP_GPIO_RE_LTC_NS_HI_CAP 500 +#define LAN8841_PTP_GPIO_RE_LTC_NS_LO_CAP 501 +#define LAN8841_PTP_GPIO_FE_LTC_SEC_HI_CAP 502 +#define LAN8841_PTP_GPIO_FE_LTC_SEC_LO_CAP 503 +#define LAN8841_PTP_GPIO_FE_LTC_NS_HI_CAP 504 +#define LAN8841_PTP_GPIO_FE_LTC_NS_LO_CAP 505 + +static void lan8841_gpio_process_cap(struct kszphy_ptp_priv *ptp_priv) +{ + struct phy_device *phydev = ptp_priv->phydev; + struct ptp_clock_event ptp_event = {0}; + int pin, ret, tmp; + s32 sec, nsec; + + pin = ptp_find_pin_unlocked(ptp_priv->ptp_clock, PTP_PF_EXTTS, 0); + if (pin == -1) + return; + + tmp = phy_read_mmd(phydev, 2, LAN8841_PTP_GPIO_CAP_STS); + if (tmp < 0) + return; + + ret = phy_write_mmd(phydev, 2, LAN8841_PTP_GPIO_SEL, + LAN8841_PTP_GPIO_SEL_GPIO_SEL(pin)); + if (ret) + return; + + mutex_lock(&ptp_priv->ptp_lock); + if (tmp & BIT(pin)) { + sec = phy_read_mmd(phydev, 2, LAN8841_PTP_GPIO_RE_LTC_SEC_HI_CAP); + sec <<= 16; + sec |= phy_read_mmd(phydev, 2, LAN8841_PTP_GPIO_RE_LTC_SEC_LO_CAP); + + nsec = phy_read_mmd(phydev, 2, LAN8841_PTP_GPIO_RE_LTC_NS_HI_CAP) & 0x3fff; + nsec <<= 16; + nsec |= phy_read_mmd(phydev, 2, LAN8841_PTP_GPIO_RE_LTC_NS_LO_CAP); + } else { + sec = phy_read_mmd(phydev, 2, LAN8841_PTP_GPIO_FE_LTC_SEC_HI_CAP); + sec <<= 16; + sec |= phy_read_mmd(phydev, 2, LAN8841_PTP_GPIO_FE_LTC_SEC_LO_CAP); + + nsec = phy_read_mmd(phydev, 2, LAN8841_PTP_GPIO_FE_LTC_NS_HI_CAP) & 0x3fff; + nsec <<= 16; + nsec |= phy_read_mmd(phydev, 2, LAN8841_PTP_GPIO_FE_LTC_NS_LO_CAP); + } + mutex_unlock(&ptp_priv->ptp_lock); + ret = phy_write_mmd(phydev, 2, LAN8841_PTP_GPIO_SEL, 0); + if (ret) + return; + + ptp_event.index = 0; + ptp_event.timestamp = ktime_set(sec, nsec); + ptp_event.type = PTP_CLOCK_EXTTS; + ptp_clock_event(ptp_priv->ptp_clock, &ptp_event); +} + +static void lan8841_handle_ptp_interrupt(struct phy_device *phydev) +{ + struct kszphy_priv *priv = phydev->priv; + struct kszphy_ptp_priv *ptp_priv = &priv->ptp_priv; + u16 status; + + do { + status = phy_read_mmd(phydev, 2, LAN8841_PTP_INT_STS); + + if (status & LAN8841_PTP_INT_STS_PTP_TX_TS_INT) + lan8841_ptp_process_tx_ts(ptp_priv); + + if (status & LAN8841_PTP_INT_STS_PTP_GPIO_CAP_INT) + lan8841_gpio_process_cap(ptp_priv); + + if (status & LAN8841_PTP_INT_STS_PTP_TX_TS_OVRFL_INT) { + lan8841_ptp_flush_fifo(ptp_priv); + skb_queue_purge(&ptp_priv->tx_queue); + } + + } while (status & (LAN8841_PTP_INT_STS_PTP_TX_TS_INT | + LAN8841_PTP_INT_STS_PTP_GPIO_CAP_INT | + LAN8841_PTP_INT_STS_PTP_TX_TS_OVRFL_INT)); +} + +#define LAN8841_INTS_PTP BIT(9) + +static irqreturn_t lan8841_handle_interrupt(struct phy_device *phydev) +{ + irqreturn_t ret = IRQ_NONE; + int irq_status; + + irq_status = phy_read(phydev, LAN8814_INTS); + if (irq_status < 0) { + phy_error(phydev); + return IRQ_NONE; + } + + if (irq_status & LAN8814_INT_LINK) { + phy_trigger_machine(phydev); + ret = IRQ_HANDLED; + } + + if (irq_status & LAN8841_INTS_PTP) { + lan8841_handle_ptp_interrupt(phydev); + ret = IRQ_HANDLED; + } + + return ret; +} + +static int lan8841_ts_info(struct mii_timestamper *mii_ts, + struct kernel_ethtool_ts_info *info) +{ + struct kszphy_ptp_priv *ptp_priv; + + ptp_priv = container_of(mii_ts, struct kszphy_ptp_priv, mii_ts); + + info->phc_index = ptp_priv->ptp_clock ? + ptp_clock_index(ptp_priv->ptp_clock) : -1; + if (info->phc_index == -1) + return 0; + + info->so_timestamping = SOF_TIMESTAMPING_TX_HARDWARE | + SOF_TIMESTAMPING_RX_HARDWARE | + SOF_TIMESTAMPING_RAW_HARDWARE; + + info->tx_types = (1 << HWTSTAMP_TX_OFF) | + (1 << HWTSTAMP_TX_ON) | + (1 << HWTSTAMP_TX_ONESTEP_SYNC); + + info->rx_filters = (1 << HWTSTAMP_FILTER_NONE) | + (1 << HWTSTAMP_FILTER_PTP_V2_L4_EVENT) | + (1 << HWTSTAMP_FILTER_PTP_V2_L2_EVENT) | + (1 << HWTSTAMP_FILTER_PTP_V2_EVENT); + + return 0; +} + +#define LAN8841_PTP_INT_EN 260 +#define LAN8841_PTP_INT_EN_PTP_TX_TS_OVRFL_EN BIT(13) +#define LAN8841_PTP_INT_EN_PTP_TX_TS_EN BIT(12) + +static void lan8841_ptp_enable_processing(struct kszphy_ptp_priv *ptp_priv, + bool enable) +{ + struct phy_device *phydev = ptp_priv->phydev; + + if (enable) { + /* Enable interrupts on the TX side */ + phy_modify_mmd(phydev, 2, LAN8841_PTP_INT_EN, + LAN8841_PTP_INT_EN_PTP_TX_TS_OVRFL_EN | + LAN8841_PTP_INT_EN_PTP_TX_TS_EN, + LAN8841_PTP_INT_EN_PTP_TX_TS_OVRFL_EN | + LAN8841_PTP_INT_EN_PTP_TX_TS_EN); + + /* Enable the modification of the frame on RX side, + * this will add the ns and 2 bits of sec in the reserved field + * of the PTP header + */ + phy_modify_mmd(phydev, KSZ9131RN_MMD_COMMON_CTRL_REG, + LAN8841_PTP_RX_MODE, + LAN8841_PTP_INSERT_TS_EN | + LAN8841_PTP_INSERT_TS_32BIT, + LAN8841_PTP_INSERT_TS_EN | + LAN8841_PTP_INSERT_TS_32BIT); + + ptp_schedule_worker(ptp_priv->ptp_clock, 0); + } else { + /* Disable interrupts on the TX side */ + phy_modify_mmd(phydev, 2, LAN8841_PTP_INT_EN, + LAN8841_PTP_INT_EN_PTP_TX_TS_OVRFL_EN | + LAN8841_PTP_INT_EN_PTP_TX_TS_EN, 0); + + /* Disable modification of the RX frames */ + phy_modify_mmd(phydev, KSZ9131RN_MMD_COMMON_CTRL_REG, + LAN8841_PTP_RX_MODE, + LAN8841_PTP_INSERT_TS_EN | + LAN8841_PTP_INSERT_TS_32BIT, 0); + + ptp_cancel_worker_sync(ptp_priv->ptp_clock); + } +} + +#define LAN8841_PTP_RX_TIMESTAMP_EN 379 +#define LAN8841_PTP_TX_TIMESTAMP_EN 443 +#define LAN8841_PTP_TX_MOD 445 + +static int lan8841_hwtstamp_set(struct mii_timestamper *mii_ts, + struct kernel_hwtstamp_config *config, + struct netlink_ext_ack *extack) +{ + struct kszphy_ptp_priv *ptp_priv = container_of(mii_ts, struct kszphy_ptp_priv, mii_ts); + struct phy_device *phydev = ptp_priv->phydev; + int txcfg = 0, rxcfg = 0; + int pkt_ts_enable; + + ptp_priv->hwts_tx_type = config->tx_type; + ptp_priv->rx_filter = config->rx_filter; + + switch (config->rx_filter) { + case HWTSTAMP_FILTER_NONE: + ptp_priv->layer = 0; + ptp_priv->version = 0; + break; + case HWTSTAMP_FILTER_PTP_V2_L4_EVENT: + case HWTSTAMP_FILTER_PTP_V2_L4_SYNC: + case HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ: + ptp_priv->layer = PTP_CLASS_L4; + ptp_priv->version = PTP_CLASS_V2; + break; + case HWTSTAMP_FILTER_PTP_V2_L2_EVENT: + case HWTSTAMP_FILTER_PTP_V2_L2_SYNC: + case HWTSTAMP_FILTER_PTP_V2_L2_DELAY_REQ: + ptp_priv->layer = PTP_CLASS_L2; + ptp_priv->version = PTP_CLASS_V2; + break; + case HWTSTAMP_FILTER_PTP_V2_EVENT: + case HWTSTAMP_FILTER_PTP_V2_SYNC: + case HWTSTAMP_FILTER_PTP_V2_DELAY_REQ: + ptp_priv->layer = PTP_CLASS_L4 | PTP_CLASS_L2; + ptp_priv->version = PTP_CLASS_V2; + break; + default: + return -ERANGE; + } + + /* Setup parsing of the frames and enable the timestamping for ptp + * frames + */ + if (ptp_priv->layer & PTP_CLASS_L2) { + rxcfg |= PTP_RX_PARSE_CONFIG_LAYER2_EN_; + txcfg |= PTP_TX_PARSE_CONFIG_LAYER2_EN_; + } else if (ptp_priv->layer & PTP_CLASS_L4) { + rxcfg |= PTP_RX_PARSE_CONFIG_IPV4_EN_ | PTP_RX_PARSE_CONFIG_IPV6_EN_; + txcfg |= PTP_TX_PARSE_CONFIG_IPV4_EN_ | PTP_TX_PARSE_CONFIG_IPV6_EN_; + } + + phy_write_mmd(phydev, 2, LAN8841_PTP_RX_PARSE_CONFIG, rxcfg); + phy_write_mmd(phydev, 2, LAN8841_PTP_TX_PARSE_CONFIG, txcfg); + + pkt_ts_enable = PTP_TIMESTAMP_EN_SYNC_ | PTP_TIMESTAMP_EN_DREQ_ | + PTP_TIMESTAMP_EN_PDREQ_ | PTP_TIMESTAMP_EN_PDRES_; + phy_write_mmd(phydev, 2, LAN8841_PTP_RX_TIMESTAMP_EN, pkt_ts_enable); + phy_write_mmd(phydev, 2, LAN8841_PTP_TX_TIMESTAMP_EN, pkt_ts_enable); + + /* Enable / disable of the TX timestamp in the SYNC frames */ + phy_modify_mmd(phydev, 2, LAN8841_PTP_TX_MOD, + PTP_TX_MOD_TX_PTP_SYNC_TS_INSERT_, + ptp_priv->hwts_tx_type == HWTSTAMP_TX_ONESTEP_SYNC ? + PTP_TX_MOD_TX_PTP_SYNC_TS_INSERT_ : 0); + + /* Now enable/disable the timestamping */ + lan8841_ptp_enable_processing(ptp_priv, + config->rx_filter != HWTSTAMP_FILTER_NONE); + + skb_queue_purge(&ptp_priv->tx_queue); + + lan8841_ptp_flush_fifo(ptp_priv); + + return 0; +} + +static bool lan8841_rxtstamp(struct mii_timestamper *mii_ts, + struct sk_buff *skb, int type) +{ + struct kszphy_ptp_priv *ptp_priv = + container_of(mii_ts, struct kszphy_ptp_priv, mii_ts); + struct ptp_header *header = ptp_parse_header(skb, type); + struct skb_shared_hwtstamps *shhwtstamps; + struct timespec64 ts; + unsigned long flags; + u32 ts_header; + + if (!header) + return false; + + if (ptp_priv->rx_filter == HWTSTAMP_FILTER_NONE || + type == PTP_CLASS_NONE) + return false; + + if ((type & ptp_priv->version) == 0 || (type & ptp_priv->layer) == 0) + return false; + + spin_lock_irqsave(&ptp_priv->seconds_lock, flags); + ts.tv_sec = ptp_priv->seconds; + spin_unlock_irqrestore(&ptp_priv->seconds_lock, flags); + ts_header = __be32_to_cpu(header->reserved2); + + shhwtstamps = skb_hwtstamps(skb); + memset(shhwtstamps, 0, sizeof(*shhwtstamps)); + + /* Check for any wrap arounds for the second part */ + if ((ts.tv_sec & GENMASK(1, 0)) == 0 && (ts_header >> 30) == 3) + ts.tv_sec -= GENMASK(1, 0) + 1; + else if ((ts.tv_sec & GENMASK(1, 0)) == 3 && (ts_header >> 30) == 0) + ts.tv_sec += 1; + + shhwtstamps->hwtstamp = + ktime_set((ts.tv_sec & ~(GENMASK(1, 0))) | ts_header >> 30, + ts_header & GENMASK(29, 0)); + header->reserved2 = 0; + + netif_rx(skb); + + return true; +} + +#define LAN8841_EVENT_A 0 +#define LAN8841_EVENT_B 1 +#define LAN8841_PTP_LTC_TARGET_SEC_HI(event) ((event) == LAN8841_EVENT_A ? 278 : 288) +#define LAN8841_PTP_LTC_TARGET_SEC_LO(event) ((event) == LAN8841_EVENT_A ? 279 : 289) +#define LAN8841_PTP_LTC_TARGET_NS_HI(event) ((event) == LAN8841_EVENT_A ? 280 : 290) +#define LAN8841_PTP_LTC_TARGET_NS_LO(event) ((event) == LAN8841_EVENT_A ? 281 : 291) + +static int lan8841_ptp_set_target(struct kszphy_ptp_priv *ptp_priv, u8 event, + s64 sec, u32 nsec) +{ + struct phy_device *phydev = ptp_priv->phydev; + int ret; + + ret = phy_write_mmd(phydev, 2, LAN8841_PTP_LTC_TARGET_SEC_HI(event), + upper_16_bits(sec)); + if (ret) + return ret; + + ret = phy_write_mmd(phydev, 2, LAN8841_PTP_LTC_TARGET_SEC_LO(event), + lower_16_bits(sec)); + if (ret) + return ret; + + ret = phy_write_mmd(phydev, 2, LAN8841_PTP_LTC_TARGET_NS_HI(event) & 0x3fff, + upper_16_bits(nsec)); + if (ret) + return ret; + + return phy_write_mmd(phydev, 2, LAN8841_PTP_LTC_TARGET_NS_LO(event), + lower_16_bits(nsec)); +} + +#define LAN8841_BUFFER_TIME 2 + +static int lan8841_ptp_update_target(struct kszphy_ptp_priv *ptp_priv, + const struct timespec64 *ts) +{ + return lan8841_ptp_set_target(ptp_priv, LAN8841_EVENT_A, + ts->tv_sec + LAN8841_BUFFER_TIME, 0); +} + +#define LAN8841_PTP_LTC_TARGET_RELOAD_SEC_HI(event) ((event) == LAN8841_EVENT_A ? 282 : 292) +#define LAN8841_PTP_LTC_TARGET_RELOAD_SEC_LO(event) ((event) == LAN8841_EVENT_A ? 283 : 293) +#define LAN8841_PTP_LTC_TARGET_RELOAD_NS_HI(event) ((event) == LAN8841_EVENT_A ? 284 : 294) +#define LAN8841_PTP_LTC_TARGET_RELOAD_NS_LO(event) ((event) == LAN8841_EVENT_A ? 285 : 295) + +static int lan8841_ptp_set_reload(struct kszphy_ptp_priv *ptp_priv, u8 event, + s64 sec, u32 nsec) +{ + struct phy_device *phydev = ptp_priv->phydev; + int ret; + + ret = phy_write_mmd(phydev, 2, LAN8841_PTP_LTC_TARGET_RELOAD_SEC_HI(event), + upper_16_bits(sec)); + if (ret) + return ret; + + ret = phy_write_mmd(phydev, 2, LAN8841_PTP_LTC_TARGET_RELOAD_SEC_LO(event), + lower_16_bits(sec)); + if (ret) + return ret; + + ret = phy_write_mmd(phydev, 2, LAN8841_PTP_LTC_TARGET_RELOAD_NS_HI(event) & 0x3fff, + upper_16_bits(nsec)); + if (ret) + return ret; + + return phy_write_mmd(phydev, 2, LAN8841_PTP_LTC_TARGET_RELOAD_NS_LO(event), + lower_16_bits(nsec)); +} + +#define LAN8841_PTP_LTC_SET_SEC_HI 262 +#define LAN8841_PTP_LTC_SET_SEC_MID 263 +#define LAN8841_PTP_LTC_SET_SEC_LO 264 +#define LAN8841_PTP_LTC_SET_NS_HI 265 +#define LAN8841_PTP_LTC_SET_NS_LO 266 +#define LAN8841_PTP_CMD_CTL_PTP_LTC_LOAD BIT(4) + +static int lan8841_ptp_settime64(struct ptp_clock_info *ptp, + const struct timespec64 *ts) +{ + struct kszphy_ptp_priv *ptp_priv = container_of(ptp, struct kszphy_ptp_priv, + ptp_clock_info); + struct phy_device *phydev = ptp_priv->phydev; + unsigned long flags; + int ret; + + /* Set the value to be stored */ + mutex_lock(&ptp_priv->ptp_lock); + phy_write_mmd(phydev, 2, LAN8841_PTP_LTC_SET_SEC_LO, lower_16_bits(ts->tv_sec)); + phy_write_mmd(phydev, 2, LAN8841_PTP_LTC_SET_SEC_MID, upper_16_bits(ts->tv_sec)); + phy_write_mmd(phydev, 2, LAN8841_PTP_LTC_SET_SEC_HI, upper_32_bits(ts->tv_sec) & 0xffff); + phy_write_mmd(phydev, 2, LAN8841_PTP_LTC_SET_NS_LO, lower_16_bits(ts->tv_nsec)); + phy_write_mmd(phydev, 2, LAN8841_PTP_LTC_SET_NS_HI, upper_16_bits(ts->tv_nsec) & 0x3fff); + + /* Set the command to load the LTC */ + phy_write_mmd(phydev, 2, LAN8841_PTP_CMD_CTL, + LAN8841_PTP_CMD_CTL_PTP_LTC_LOAD); + ret = lan8841_ptp_update_target(ptp_priv, ts); + mutex_unlock(&ptp_priv->ptp_lock); + + spin_lock_irqsave(&ptp_priv->seconds_lock, flags); + ptp_priv->seconds = ts->tv_sec; + spin_unlock_irqrestore(&ptp_priv->seconds_lock, flags); + + return ret; +} + +#define LAN8841_PTP_LTC_RD_SEC_HI 358 +#define LAN8841_PTP_LTC_RD_SEC_MID 359 +#define LAN8841_PTP_LTC_RD_SEC_LO 360 +#define LAN8841_PTP_LTC_RD_NS_HI 361 +#define LAN8841_PTP_LTC_RD_NS_LO 362 +#define LAN8841_PTP_CMD_CTL_PTP_LTC_READ BIT(3) + +static int lan8841_ptp_gettime64(struct ptp_clock_info *ptp, + struct timespec64 *ts) +{ + struct kszphy_ptp_priv *ptp_priv = container_of(ptp, struct kszphy_ptp_priv, + ptp_clock_info); + struct phy_device *phydev = ptp_priv->phydev; + time64_t s; + s64 ns; + + mutex_lock(&ptp_priv->ptp_lock); + /* Issue the command to read the LTC */ + phy_write_mmd(phydev, 2, LAN8841_PTP_CMD_CTL, + LAN8841_PTP_CMD_CTL_PTP_LTC_READ); + + /* Read the LTC */ + s = phy_read_mmd(phydev, 2, LAN8841_PTP_LTC_RD_SEC_HI); + s <<= 16; + s |= phy_read_mmd(phydev, 2, LAN8841_PTP_LTC_RD_SEC_MID); + s <<= 16; + s |= phy_read_mmd(phydev, 2, LAN8841_PTP_LTC_RD_SEC_LO); + + ns = phy_read_mmd(phydev, 2, LAN8841_PTP_LTC_RD_NS_HI) & 0x3fff; + ns <<= 16; + ns |= phy_read_mmd(phydev, 2, LAN8841_PTP_LTC_RD_NS_LO); + mutex_unlock(&ptp_priv->ptp_lock); + + set_normalized_timespec64(ts, s, ns); + return 0; +} + +static void lan8841_ptp_getseconds(struct ptp_clock_info *ptp, + struct timespec64 *ts) +{ + struct kszphy_ptp_priv *ptp_priv = container_of(ptp, struct kszphy_ptp_priv, + ptp_clock_info); + struct phy_device *phydev = ptp_priv->phydev; + time64_t s; + + mutex_lock(&ptp_priv->ptp_lock); + /* Issue the command to read the LTC */ + phy_write_mmd(phydev, 2, LAN8841_PTP_CMD_CTL, + LAN8841_PTP_CMD_CTL_PTP_LTC_READ); + + /* Read the LTC */ + s = phy_read_mmd(phydev, 2, LAN8841_PTP_LTC_RD_SEC_HI); + s <<= 16; + s |= phy_read_mmd(phydev, 2, LAN8841_PTP_LTC_RD_SEC_MID); + s <<= 16; + s |= phy_read_mmd(phydev, 2, LAN8841_PTP_LTC_RD_SEC_LO); + mutex_unlock(&ptp_priv->ptp_lock); + + set_normalized_timespec64(ts, s, 0); +} + +#define LAN8841_PTP_LTC_STEP_ADJ_LO 276 +#define LAN8841_PTP_LTC_STEP_ADJ_HI 275 +#define LAN8841_PTP_LTC_STEP_ADJ_DIR BIT(15) +#define LAN8841_PTP_CMD_CTL_PTP_LTC_STEP_SECONDS BIT(5) +#define LAN8841_PTP_CMD_CTL_PTP_LTC_STEP_NANOSECONDS BIT(6) + +static int lan8841_ptp_adjtime(struct ptp_clock_info *ptp, s64 delta) +{ + struct kszphy_ptp_priv *ptp_priv = container_of(ptp, struct kszphy_ptp_priv, + ptp_clock_info); + struct phy_device *phydev = ptp_priv->phydev; + struct timespec64 ts; + bool add = true; + u32 nsec; + s32 sec; + int ret; + + /* The HW allows up to 15 sec to adjust the time, but here we limit to + * 10 sec the adjustment. The reason is, in case the adjustment is 14 + * sec and 999999999 nsec, then we add 8ns to compansate the actual + * increment so the value can be bigger than 15 sec. Therefore limit the + * possible adjustments so we will not have these corner cases + */ + if (delta > 10000000000LL || delta < -10000000000LL) { + /* The timeadjustment is too big, so fall back using set time */ + u64 now; + + ptp->gettime64(ptp, &ts); + + now = ktime_to_ns(timespec64_to_ktime(ts)); + ts = ns_to_timespec64(now + delta); + + ptp->settime64(ptp, &ts); + return 0; + } + + sec = div_u64_rem(delta < 0 ? -delta : delta, NSEC_PER_SEC, &nsec); + if (delta < 0 && nsec != 0) { + /* It is not allowed to adjust low the nsec part, therefore + * subtract more from second part and add to nanosecond such + * that would roll over, so the second part will increase + */ + sec--; + nsec = NSEC_PER_SEC - nsec; + } + + /* Calculate the adjustments and the direction */ + if (delta < 0) + add = false; + + if (nsec > 0) + /* add 8 ns to cover the likely normal increment */ + nsec += 8; + + if (nsec >= NSEC_PER_SEC) { + /* carry into seconds */ + sec++; + nsec -= NSEC_PER_SEC; + } + + mutex_lock(&ptp_priv->ptp_lock); + if (sec) { + phy_write_mmd(phydev, 2, LAN8841_PTP_LTC_STEP_ADJ_LO, sec); + phy_write_mmd(phydev, 2, LAN8841_PTP_LTC_STEP_ADJ_HI, + add ? LAN8841_PTP_LTC_STEP_ADJ_DIR : 0); + phy_write_mmd(phydev, 2, LAN8841_PTP_CMD_CTL, + LAN8841_PTP_CMD_CTL_PTP_LTC_STEP_SECONDS); + } + + if (nsec) { + phy_write_mmd(phydev, 2, LAN8841_PTP_LTC_STEP_ADJ_LO, + nsec & 0xffff); + phy_write_mmd(phydev, 2, LAN8841_PTP_LTC_STEP_ADJ_HI, + (nsec >> 16) & 0x3fff); + phy_write_mmd(phydev, 2, LAN8841_PTP_CMD_CTL, + LAN8841_PTP_CMD_CTL_PTP_LTC_STEP_NANOSECONDS); + } + mutex_unlock(&ptp_priv->ptp_lock); + + /* Update the target clock */ + ptp->gettime64(ptp, &ts); + mutex_lock(&ptp_priv->ptp_lock); + ret = lan8841_ptp_update_target(ptp_priv, &ts); + mutex_unlock(&ptp_priv->ptp_lock); + + return ret; +} + +#define LAN8841_PTP_LTC_RATE_ADJ_HI 269 +#define LAN8841_PTP_LTC_RATE_ADJ_HI_DIR BIT(15) +#define LAN8841_PTP_LTC_RATE_ADJ_LO 270 + +static int lan8841_ptp_adjfine(struct ptp_clock_info *ptp, long scaled_ppm) +{ + struct kszphy_ptp_priv *ptp_priv = container_of(ptp, struct kszphy_ptp_priv, + ptp_clock_info); + struct phy_device *phydev = ptp_priv->phydev; + bool faster = true; + u32 rate; + + if (!scaled_ppm) + return 0; + + if (scaled_ppm < 0) { + scaled_ppm = -scaled_ppm; + faster = false; + } + + rate = LAN8841_1PPM_FORMAT * (upper_16_bits(scaled_ppm)); + rate += (LAN8841_1PPM_FORMAT * (lower_16_bits(scaled_ppm))) >> 16; + + mutex_lock(&ptp_priv->ptp_lock); + phy_write_mmd(phydev, 2, LAN8841_PTP_LTC_RATE_ADJ_HI, + faster ? LAN8841_PTP_LTC_RATE_ADJ_HI_DIR | (upper_16_bits(rate) & 0x3fff) + : upper_16_bits(rate) & 0x3fff); + phy_write_mmd(phydev, 2, LAN8841_PTP_LTC_RATE_ADJ_LO, lower_16_bits(rate)); + mutex_unlock(&ptp_priv->ptp_lock); + + return 0; +} + +static int lan8841_ptp_verify(struct ptp_clock_info *ptp, unsigned int pin, + enum ptp_pin_function func, unsigned int chan) +{ + switch (func) { + case PTP_PF_NONE: + case PTP_PF_PEROUT: + case PTP_PF_EXTTS: + break; + default: + return -1; + } + + return 0; +} + +#define LAN8841_PTP_GPIO_NUM 10 +#define LAN8841_GPIO_EN 128 +#define LAN8841_GPIO_DIR 129 +#define LAN8841_GPIO_BUF 130 + +static int lan8841_ptp_perout_off(struct kszphy_ptp_priv *ptp_priv, int pin) +{ + struct phy_device *phydev = ptp_priv->phydev; + int ret; + + ret = phy_clear_bits_mmd(phydev, 2, LAN8841_GPIO_EN, BIT(pin)); + if (ret) + return ret; + + ret = phy_clear_bits_mmd(phydev, 2, LAN8841_GPIO_DIR, BIT(pin)); + if (ret) + return ret; + + return phy_clear_bits_mmd(phydev, 2, LAN8841_GPIO_BUF, BIT(pin)); +} + +static int lan8841_ptp_perout_on(struct kszphy_ptp_priv *ptp_priv, int pin) +{ + struct phy_device *phydev = ptp_priv->phydev; + int ret; + + ret = phy_set_bits_mmd(phydev, 2, LAN8841_GPIO_EN, BIT(pin)); + if (ret) + return ret; + + ret = phy_set_bits_mmd(phydev, 2, LAN8841_GPIO_DIR, BIT(pin)); + if (ret) + return ret; + + return phy_set_bits_mmd(phydev, 2, LAN8841_GPIO_BUF, BIT(pin)); +} + +#define LAN8841_GPIO_DATA_SEL1 131 +#define LAN8841_GPIO_DATA_SEL2 132 +#define LAN8841_GPIO_DATA_SEL_GPIO_DATA_SEL_EVENT_MASK GENMASK(2, 0) +#define LAN8841_GPIO_DATA_SEL_GPIO_DATA_SEL_EVENT_A 1 +#define LAN8841_GPIO_DATA_SEL_GPIO_DATA_SEL_EVENT_B 2 +#define LAN8841_PTP_GENERAL_CONFIG 257 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_POL_A BIT(1) +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_POL_B BIT(3) +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_A_MASK GENMASK(7, 4) +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_B_MASK GENMASK(11, 8) +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_A 4 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_B 7 + +static int lan8841_ptp_remove_event(struct kszphy_ptp_priv *ptp_priv, int pin, + u8 event) +{ + struct phy_device *phydev = ptp_priv->phydev; + u16 tmp; + int ret; + + /* Now remove pin from the event. GPIO_DATA_SEL1 contains the GPIO + * pins 0-4 while GPIO_DATA_SEL2 contains GPIO pins 5-9, therefore + * depending on the pin, it requires to read a different register + */ + if (pin < 5) { + tmp = LAN8841_GPIO_DATA_SEL_GPIO_DATA_SEL_EVENT_MASK << (3 * pin); + ret = phy_clear_bits_mmd(phydev, 2, LAN8841_GPIO_DATA_SEL1, tmp); + } else { + tmp = LAN8841_GPIO_DATA_SEL_GPIO_DATA_SEL_EVENT_MASK << (3 * (pin - 5)); + ret = phy_clear_bits_mmd(phydev, 2, LAN8841_GPIO_DATA_SEL2, tmp); + } + if (ret) + return ret; + + /* Disable the event */ + if (event == LAN8841_EVENT_A) + tmp = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_POL_A | + LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_A_MASK; + else + tmp = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_POL_B | + LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_B_MASK; + return phy_clear_bits_mmd(phydev, 2, LAN8841_GPIO_EN, tmp); +} + +static int lan8841_ptp_enable_event(struct kszphy_ptp_priv *ptp_priv, int pin, + u8 event, int pulse_width) +{ + struct phy_device *phydev = ptp_priv->phydev; + u16 tmp; + int ret; + + /* Enable the event */ + if (event == LAN8841_EVENT_A) + ret = phy_modify_mmd(phydev, 2, LAN8841_PTP_GENERAL_CONFIG, + LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_POL_A | + LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_A_MASK, + LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_POL_A | + pulse_width << LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_A); + else + ret = phy_modify_mmd(phydev, 2, LAN8841_PTP_GENERAL_CONFIG, + LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_POL_B | + LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_B_MASK, + LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_POL_B | + pulse_width << LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_B); + if (ret) + return ret; + + /* Now connect the pin to the event. GPIO_DATA_SEL1 contains the GPIO + * pins 0-4 while GPIO_DATA_SEL2 contains GPIO pins 5-9, therefore + * depending on the pin, it requires to read a different register + */ + if (event == LAN8841_EVENT_A) + tmp = LAN8841_GPIO_DATA_SEL_GPIO_DATA_SEL_EVENT_A; + else + tmp = LAN8841_GPIO_DATA_SEL_GPIO_DATA_SEL_EVENT_B; + + if (pin < 5) + ret = phy_set_bits_mmd(phydev, 2, LAN8841_GPIO_DATA_SEL1, + tmp << (3 * pin)); + else + ret = phy_set_bits_mmd(phydev, 2, LAN8841_GPIO_DATA_SEL2, + tmp << (3 * (pin - 5))); + + return ret; +} + +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_200MS 13 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_100MS 12 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_50MS 11 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_10MS 10 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_5MS 9 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_1MS 8 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_500US 7 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_100US 6 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_50US 5 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_10US 4 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_5US 3 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_1US 2 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_500NS 1 +#define LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_100NS 0 + +static int lan8841_ptp_perout(struct ptp_clock_info *ptp, + struct ptp_clock_request *rq, int on) +{ + struct kszphy_ptp_priv *ptp_priv = container_of(ptp, struct kszphy_ptp_priv, + ptp_clock_info); + struct phy_device *phydev = ptp_priv->phydev; + struct timespec64 ts_on, ts_period; + s64 on_nsec, period_nsec; + int pulse_width; + int pin; + int ret; + + pin = ptp_find_pin(ptp_priv->ptp_clock, PTP_PF_PEROUT, rq->perout.index); + if (pin == -1 || pin >= LAN8841_PTP_GPIO_NUM) + return -EINVAL; + + if (!on) { + ret = lan8841_ptp_perout_off(ptp_priv, pin); + if (ret) + return ret; + + return lan8841_ptp_remove_event(ptp_priv, LAN8841_EVENT_A, pin); + } + + ts_on.tv_sec = rq->perout.on.sec; + ts_on.tv_nsec = rq->perout.on.nsec; + on_nsec = timespec64_to_ns(&ts_on); + + ts_period.tv_sec = rq->perout.period.sec; + ts_period.tv_nsec = rq->perout.period.nsec; + period_nsec = timespec64_to_ns(&ts_period); + + if (period_nsec < 200) { + pr_warn_ratelimited("%s: perout period too small, minimum is 200 nsec\n", + phydev_name(phydev)); + return -EOPNOTSUPP; + } + + if (on_nsec >= period_nsec) { + pr_warn_ratelimited("%s: pulse width must be smaller than period\n", + phydev_name(phydev)); + return -EINVAL; + } + + switch (on_nsec) { + case 200000000: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_200MS; + break; + case 100000000: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_100MS; + break; + case 50000000: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_50MS; + break; + case 10000000: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_10MS; + break; + case 5000000: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_5MS; + break; + case 1000000: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_1MS; + break; + case 500000: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_500US; + break; + case 100000: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_100US; + break; + case 50000: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_50US; + break; + case 10000: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_10US; + break; + case 5000: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_5US; + break; + case 1000: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_1US; + break; + case 500: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_500NS; + break; + case 100: + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_100NS; + break; + default: + pr_warn_ratelimited("%s: Use default duty cycle of 100ns\n", + phydev_name(phydev)); + pulse_width = LAN8841_PTP_GENERAL_CONFIG_LTC_EVENT_100NS; + break; + } + + mutex_lock(&ptp_priv->ptp_lock); + ret = lan8841_ptp_set_target(ptp_priv, LAN8841_EVENT_A, rq->perout.start.sec, + rq->perout.start.nsec); + mutex_unlock(&ptp_priv->ptp_lock); + if (ret) + return ret; + + ret = lan8841_ptp_set_reload(ptp_priv, LAN8841_EVENT_A, rq->perout.period.sec, + rq->perout.period.nsec); + if (ret) + return ret; + + ret = lan8841_ptp_enable_event(ptp_priv, pin, LAN8841_EVENT_A, + pulse_width); + if (ret) + return ret; + + ret = lan8841_ptp_perout_on(ptp_priv, pin); + if (ret) + lan8841_ptp_remove_event(ptp_priv, pin, LAN8841_EVENT_A); + + return ret; +} + +#define LAN8841_PTP_GPIO_CAP_EN 496 +#define LAN8841_PTP_GPIO_CAP_EN_GPIO_RE_CAPTURE_ENABLE(gpio) (BIT(gpio)) +#define LAN8841_PTP_GPIO_CAP_EN_GPIO_FE_CAPTURE_ENABLE(gpio) (BIT(gpio) << 8) +#define LAN8841_PTP_INT_EN_PTP_GPIO_CAP_EN BIT(2) + +static int lan8841_ptp_extts_on(struct kszphy_ptp_priv *ptp_priv, int pin, + u32 flags) +{ + struct phy_device *phydev = ptp_priv->phydev; + u16 tmp = 0; + int ret; + + /* Set GPIO to be input */ + ret = phy_set_bits_mmd(phydev, 2, LAN8841_GPIO_EN, BIT(pin)); + if (ret) + return ret; + + ret = phy_clear_bits_mmd(phydev, 2, LAN8841_GPIO_BUF, BIT(pin)); + if (ret) + return ret; + + /* Enable capture on the edges of the pin */ + if (flags & PTP_RISING_EDGE) + tmp |= LAN8841_PTP_GPIO_CAP_EN_GPIO_RE_CAPTURE_ENABLE(pin); + if (flags & PTP_FALLING_EDGE) + tmp |= LAN8841_PTP_GPIO_CAP_EN_GPIO_FE_CAPTURE_ENABLE(pin); + ret = phy_write_mmd(phydev, 2, LAN8841_PTP_GPIO_CAP_EN, tmp); + if (ret) + return ret; + + /* Enable interrupt */ + return phy_modify_mmd(phydev, 2, LAN8841_PTP_INT_EN, + LAN8841_PTP_INT_EN_PTP_GPIO_CAP_EN, + LAN8841_PTP_INT_EN_PTP_GPIO_CAP_EN); +} + +static int lan8841_ptp_extts_off(struct kszphy_ptp_priv *ptp_priv, int pin) +{ + struct phy_device *phydev = ptp_priv->phydev; + int ret; + + /* Set GPIO to be output */ + ret = phy_clear_bits_mmd(phydev, 2, LAN8841_GPIO_EN, BIT(pin)); + if (ret) + return ret; + + ret = phy_clear_bits_mmd(phydev, 2, LAN8841_GPIO_BUF, BIT(pin)); + if (ret) + return ret; + + /* Disable capture on both of the edges */ + ret = phy_modify_mmd(phydev, 2, LAN8841_PTP_GPIO_CAP_EN, + LAN8841_PTP_GPIO_CAP_EN_GPIO_RE_CAPTURE_ENABLE(pin) | + LAN8841_PTP_GPIO_CAP_EN_GPIO_FE_CAPTURE_ENABLE(pin), + 0); + if (ret) + return ret; + + /* Disable interrupt */ + return phy_modify_mmd(phydev, 2, LAN8841_PTP_INT_EN, + LAN8841_PTP_INT_EN_PTP_GPIO_CAP_EN, + 0); +} + +static int lan8841_ptp_extts(struct ptp_clock_info *ptp, + struct ptp_clock_request *rq, int on) +{ + struct kszphy_ptp_priv *ptp_priv = container_of(ptp, struct kszphy_ptp_priv, + ptp_clock_info); + int pin; + int ret; + + /* Reject requests with unsupported flags */ + if (rq->extts.flags & ~(PTP_ENABLE_FEATURE | + PTP_EXTTS_EDGES | + PTP_STRICT_FLAGS)) + return -EOPNOTSUPP; + + pin = ptp_find_pin(ptp_priv->ptp_clock, PTP_PF_EXTTS, rq->extts.index); + if (pin == -1 || pin >= LAN8841_PTP_GPIO_NUM) + return -EINVAL; + + mutex_lock(&ptp_priv->ptp_lock); + if (on) + ret = lan8841_ptp_extts_on(ptp_priv, pin, rq->extts.flags); + else + ret = lan8841_ptp_extts_off(ptp_priv, pin); + mutex_unlock(&ptp_priv->ptp_lock); + + return ret; +} + +static int lan8841_ptp_enable(struct ptp_clock_info *ptp, + struct ptp_clock_request *rq, int on) +{ + switch (rq->type) { + case PTP_CLK_REQ_EXTTS: + return lan8841_ptp_extts(ptp, rq, on); + case PTP_CLK_REQ_PEROUT: + return lan8841_ptp_perout(ptp, rq, on); + default: + return -EOPNOTSUPP; + } + + return 0; +} + +static long lan8841_ptp_do_aux_work(struct ptp_clock_info *ptp) +{ + struct kszphy_ptp_priv *ptp_priv = container_of(ptp, struct kszphy_ptp_priv, + ptp_clock_info); + struct timespec64 ts; + unsigned long flags; + + lan8841_ptp_getseconds(&ptp_priv->ptp_clock_info, &ts); + + spin_lock_irqsave(&ptp_priv->seconds_lock, flags); + ptp_priv->seconds = ts.tv_sec; + spin_unlock_irqrestore(&ptp_priv->seconds_lock, flags); + + return nsecs_to_jiffies(LAN8841_GET_SEC_LTC_DELAY); +} + +static struct ptp_clock_info lan8841_ptp_clock_info = { + .owner = THIS_MODULE, + .name = "lan8841 ptp", + .max_adj = 31249999, + .gettime64 = lan8841_ptp_gettime64, + .settime64 = lan8841_ptp_settime64, + .adjtime = lan8841_ptp_adjtime, + .adjfine = lan8841_ptp_adjfine, + .verify = lan8841_ptp_verify, + .enable = lan8841_ptp_enable, + .do_aux_work = lan8841_ptp_do_aux_work, + .n_per_out = LAN8841_PTP_GPIO_NUM, + .n_ext_ts = LAN8841_PTP_GPIO_NUM, + .n_pins = LAN8841_PTP_GPIO_NUM, + .supported_perout_flags = PTP_PEROUT_DUTY_CYCLE, +}; + +#define LAN8841_OPERATION_MODE_STRAP_LOW_REGISTER 3 +#define LAN8841_OPERATION_MODE_STRAP_LOW_REGISTER_STRAP_RGMII_EN BIT(0) + +static int lan8841_probe(struct phy_device *phydev) +{ + struct kszphy_ptp_priv *ptp_priv; + struct kszphy_priv *priv; + int err; + + err = kszphy_probe(phydev); + if (err) + return err; + + if (phy_read_mmd(phydev, KSZ9131RN_MMD_COMMON_CTRL_REG, + LAN8841_OPERATION_MODE_STRAP_LOW_REGISTER) & + LAN8841_OPERATION_MODE_STRAP_LOW_REGISTER_STRAP_RGMII_EN) + phydev->interface = PHY_INTERFACE_MODE_RGMII_RXID; + + /* Register the clock */ + if (!IS_ENABLED(CONFIG_NETWORK_PHY_TIMESTAMPING)) + return 0; + + priv = phydev->priv; + ptp_priv = &priv->ptp_priv; + + ptp_priv->pin_config = devm_kcalloc(&phydev->mdio.dev, + LAN8841_PTP_GPIO_NUM, + sizeof(*ptp_priv->pin_config), + GFP_KERNEL); + if (!ptp_priv->pin_config) + return -ENOMEM; + + for (int i = 0; i < LAN8841_PTP_GPIO_NUM; ++i) { + struct ptp_pin_desc *p = &ptp_priv->pin_config[i]; + + snprintf(p->name, sizeof(p->name), "pin%d", i); + p->index = i; + p->func = PTP_PF_NONE; + } + + ptp_priv->ptp_clock_info = lan8841_ptp_clock_info; + ptp_priv->ptp_clock_info.pin_config = ptp_priv->pin_config; + ptp_priv->ptp_clock = ptp_clock_register(&ptp_priv->ptp_clock_info, + &phydev->mdio.dev); + if (IS_ERR(ptp_priv->ptp_clock)) { + phydev_err(phydev, "ptp_clock_register failed: %pe\n", + ptp_priv->ptp_clock); + return -EINVAL; + } + + if (!ptp_priv->ptp_clock) + return 0; + + /* Initialize the SW */ + skb_queue_head_init(&ptp_priv->tx_queue); + ptp_priv->phydev = phydev; + mutex_init(&ptp_priv->ptp_lock); + spin_lock_init(&ptp_priv->seconds_lock); + + ptp_priv->mii_ts.rxtstamp = lan8841_rxtstamp; + ptp_priv->mii_ts.txtstamp = lan8814_txtstamp; + ptp_priv->mii_ts.hwtstamp_set = lan8841_hwtstamp_set; + ptp_priv->mii_ts.ts_info = lan8841_ts_info; + + phydev->mii_ts = &ptp_priv->mii_ts; + + /* Timestamp selected by default to keep legacy API */ + phydev->default_timestamp = true; + + return 0; +} + +static int lan8804_resume(struct phy_device *phydev) +{ + return kszphy_resume(phydev); +} + +static int lan8804_suspend(struct phy_device *phydev) +{ + return kszphy_generic_suspend(phydev); +} + +static int lan8841_resume(struct phy_device *phydev) +{ + return kszphy_generic_resume(phydev); +} + +static int lan8841_suspend(struct phy_device *phydev) +{ + struct kszphy_priv *priv = phydev->priv; + struct kszphy_ptp_priv *ptp_priv = &priv->ptp_priv; + + if (ptp_priv->ptp_clock) + ptp_cancel_worker_sync(ptp_priv->ptp_clock); + + return kszphy_generic_suspend(phydev); +} + +static int ksz9131_resume(struct phy_device *phydev) +{ + if (phydev->suspended && phy_interface_is_rgmii(phydev)) + ksz9131_config_rgmii_delay(phydev); + + return kszphy_resume(phydev); +} + +#define LAN8842_PTP_GPIO_NUM 16 + +static int lan8842_ptp_probe_once(struct phy_device *phydev) +{ + return __lan8814_ptp_probe_once(phydev, "lan8842_ptp_pin", + LAN8842_PTP_GPIO_NUM); +} + +#define LAN8842_STRAP_REG 0 /* 0x0 */ +#define LAN8842_STRAP_REG_PHYADDR_MASK GENMASK(4, 0) +#define LAN8842_SKU_REG 11 /* 0x0b */ +#define LAN8842_SELF_TEST 14 /* 0x0e */ +#define LAN8842_SELF_TEST_RX_CNT_ENA BIT(8) +#define LAN8842_SELF_TEST_TX_CNT_ENA BIT(4) + +static int lan8842_probe(struct phy_device *phydev) +{ + struct lan8842_priv *priv; + int addr; + int ret; + + priv = devm_kzalloc(&phydev->mdio.dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + phydev->priv = priv; + + /* Similar to lan8814 this PHY has a pin which needs to be pulled down + * to enable to pass any traffic through it. Therefore use the same + * function as lan8814 + */ + ret = lan8814_release_coma_mode(phydev); + if (ret) + return ret; + + /* Enable to count the RX and TX packets */ + ret = lanphy_write_page_reg(phydev, LAN8814_PAGE_PCS_DIGITAL, + LAN8842_SELF_TEST, + LAN8842_SELF_TEST_RX_CNT_ENA | + LAN8842_SELF_TEST_TX_CNT_ENA); + if (ret < 0) + return ret; + + /* Revision lan8832 doesn't have support for PTP, therefore don't add + * any PTP clocks + */ + ret = lanphy_read_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + LAN8842_SKU_REG); + if (ret < 0) + return ret; + + priv->rev = ret; + if (priv->rev == LAN8842_REV_8832) + return 0; + + /* As the lan8814 and lan8842 has the same IP for the PTP block, the + * only difference is the number of the GPIOs, then make sure that the + * lan8842 initialized also the shared data pointer as this is used in + * all the PTP functions for lan8814. The lan8842 doesn't have multiple + * PHYs in the same package. + */ + addr = lanphy_read_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + LAN8842_STRAP_REG); + if (addr < 0) + return addr; + addr &= LAN8842_STRAP_REG_PHYADDR_MASK; + + ret = devm_phy_package_join(&phydev->mdio.dev, phydev, addr, + sizeof(struct lan8814_shared_priv)); + if (ret) + return ret; + + if (phy_package_init_once(phydev)) { + ret = lan8842_ptp_probe_once(phydev); + if (ret) + return ret; + } + + lan8814_ptp_init(phydev); + return 0; } +#define LAN8814_POWER_MGMT_MODE_3_ANEG_MDI 0x13 +#define LAN8814_POWER_MGMT_MODE_4_ANEG_MDIX 0x14 +#define LAN8814_POWER_MGMT_MODE_5_10BT_MDI 0x15 +#define LAN8814_POWER_MGMT_MODE_6_10BT_MDIX 0x16 +#define LAN8814_POWER_MGMT_MODE_7_100BT_TRAIN 0x17 +#define LAN8814_POWER_MGMT_MODE_8_100BT_MDI 0x18 +#define LAN8814_POWER_MGMT_MODE_9_100BT_EEE_MDI_TX 0x19 +#define LAN8814_POWER_MGMT_MODE_10_100BT_EEE_MDI_RX 0x1a +#define LAN8814_POWER_MGMT_MODE_11_100BT_MDIX 0x1b +#define LAN8814_POWER_MGMT_MODE_12_100BT_EEE_MDIX_TX 0x1c +#define LAN8814_POWER_MGMT_MODE_13_100BT_EEE_MDIX_RX 0x1d +#define LAN8814_POWER_MGMT_MODE_14_100BTX_EEE_TX_RX 0x1e + +#define LAN8814_POWER_MGMT_DLLPD_D BIT(0) +#define LAN8814_POWER_MGMT_ADCPD_D BIT(1) +#define LAN8814_POWER_MGMT_PGAPD_D BIT(2) +#define LAN8814_POWER_MGMT_TXPD_D BIT(3) +#define LAN8814_POWER_MGMT_DLLPD_C BIT(4) +#define LAN8814_POWER_MGMT_ADCPD_C BIT(5) +#define LAN8814_POWER_MGMT_PGAPD_C BIT(6) +#define LAN8814_POWER_MGMT_TXPD_C BIT(7) +#define LAN8814_POWER_MGMT_DLLPD_B BIT(8) +#define LAN8814_POWER_MGMT_ADCPD_B BIT(9) +#define LAN8814_POWER_MGMT_PGAPD_B BIT(10) +#define LAN8814_POWER_MGMT_TXPD_B BIT(11) +#define LAN8814_POWER_MGMT_DLLPD_A BIT(12) +#define LAN8814_POWER_MGMT_ADCPD_A BIT(13) +#define LAN8814_POWER_MGMT_PGAPD_A BIT(14) +#define LAN8814_POWER_MGMT_TXPD_A BIT(15) + +#define LAN8814_POWER_MGMT_C_D (LAN8814_POWER_MGMT_DLLPD_D | \ + LAN8814_POWER_MGMT_ADCPD_D | \ + LAN8814_POWER_MGMT_PGAPD_D | \ + LAN8814_POWER_MGMT_DLLPD_C | \ + LAN8814_POWER_MGMT_ADCPD_C | \ + LAN8814_POWER_MGMT_PGAPD_C) + +#define LAN8814_POWER_MGMT_B_C_D (LAN8814_POWER_MGMT_C_D | \ + LAN8814_POWER_MGMT_DLLPD_B | \ + LAN8814_POWER_MGMT_ADCPD_B | \ + LAN8814_POWER_MGMT_PGAPD_B) + +#define LAN8814_POWER_MGMT_VAL1 (LAN8814_POWER_MGMT_C_D | \ + LAN8814_POWER_MGMT_ADCPD_B | \ + LAN8814_POWER_MGMT_PGAPD_B | \ + LAN8814_POWER_MGMT_ADCPD_A | \ + LAN8814_POWER_MGMT_PGAPD_A) + +#define LAN8814_POWER_MGMT_VAL2 LAN8814_POWER_MGMT_C_D + +#define LAN8814_POWER_MGMT_VAL3 (LAN8814_POWER_MGMT_C_D | \ + LAN8814_POWER_MGMT_DLLPD_B | \ + LAN8814_POWER_MGMT_ADCPD_B | \ + LAN8814_POWER_MGMT_PGAPD_A) + +#define LAN8814_POWER_MGMT_VAL4 (LAN8814_POWER_MGMT_B_C_D | \ + LAN8814_POWER_MGMT_ADCPD_A | \ + LAN8814_POWER_MGMT_PGAPD_A) + +#define LAN8814_POWER_MGMT_VAL5 LAN8814_POWER_MGMT_B_C_D + +#define LAN8814_EEE_WAKE_TX_TIMER 0x0e +#define LAN8814_EEE_WAKE_TX_TIMER_MAX_VAL 0x1f + +static const struct lanphy_reg_data short_center_tap_errata[] = { + { LAN8814_PAGE_POWER_REGS, + LAN8814_POWER_MGMT_MODE_3_ANEG_MDI, + LAN8814_POWER_MGMT_VAL1 }, + { LAN8814_PAGE_POWER_REGS, + LAN8814_POWER_MGMT_MODE_4_ANEG_MDIX, + LAN8814_POWER_MGMT_VAL1 }, + { LAN8814_PAGE_POWER_REGS, + LAN8814_POWER_MGMT_MODE_5_10BT_MDI, + LAN8814_POWER_MGMT_VAL1 }, + { LAN8814_PAGE_POWER_REGS, + LAN8814_POWER_MGMT_MODE_6_10BT_MDIX, + LAN8814_POWER_MGMT_VAL1 }, + { LAN8814_PAGE_POWER_REGS, + LAN8814_POWER_MGMT_MODE_7_100BT_TRAIN, + LAN8814_POWER_MGMT_VAL2 }, + { LAN8814_PAGE_POWER_REGS, + LAN8814_POWER_MGMT_MODE_8_100BT_MDI, + LAN8814_POWER_MGMT_VAL3 }, + { LAN8814_PAGE_POWER_REGS, + LAN8814_POWER_MGMT_MODE_9_100BT_EEE_MDI_TX, + LAN8814_POWER_MGMT_VAL3 }, + { LAN8814_PAGE_POWER_REGS, + LAN8814_POWER_MGMT_MODE_10_100BT_EEE_MDI_RX, + LAN8814_POWER_MGMT_VAL4 }, + { LAN8814_PAGE_POWER_REGS, + LAN8814_POWER_MGMT_MODE_11_100BT_MDIX, + LAN8814_POWER_MGMT_VAL5 }, + { LAN8814_PAGE_POWER_REGS, + LAN8814_POWER_MGMT_MODE_12_100BT_EEE_MDIX_TX, + LAN8814_POWER_MGMT_VAL5 }, + { LAN8814_PAGE_POWER_REGS, + LAN8814_POWER_MGMT_MODE_13_100BT_EEE_MDIX_RX, + LAN8814_POWER_MGMT_VAL4 }, + { LAN8814_PAGE_POWER_REGS, + LAN8814_POWER_MGMT_MODE_14_100BTX_EEE_TX_RX, + LAN8814_POWER_MGMT_VAL4 }, +}; + +static const struct lanphy_reg_data waketx_timer_errata[] = { + { LAN8814_PAGE_EEE, + LAN8814_EEE_WAKE_TX_TIMER, + LAN8814_EEE_WAKE_TX_TIMER_MAX_VAL }, +}; + +static int lanphy_write_reg_data(struct phy_device *phydev, + const struct lanphy_reg_data *data, + size_t num) +{ + int ret = 0; + + while (num--) { + ret = lanphy_write_page_reg(phydev, data->page, data->addr, + data->val); + if (ret) + break; + } + + return ret; +} + +static int lan8842_erratas(struct phy_device *phydev) +{ + int ret; + + ret = lanphy_write_reg_data(phydev, short_center_tap_errata, + ARRAY_SIZE(short_center_tap_errata)); + if (ret) + return ret; + + return lanphy_write_reg_data(phydev, waketx_timer_errata, + ARRAY_SIZE(waketx_timer_errata)); +} + +static int lan8842_config_init(struct phy_device *phydev) +{ + int ret; + + /* Reset the PHY */ + ret = lanphy_modify_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + LAN8814_QSGMII_SOFT_RESET, + LAN8814_QSGMII_SOFT_RESET_BIT, + LAN8814_QSGMII_SOFT_RESET_BIT); + if (ret < 0) + return ret; + + /* Apply the erratas for this device */ + ret = lan8842_erratas(phydev); + if (ret < 0) + return ret; + + /* Even if the GPIOs are set to control the LEDs the behaviour of the + * LEDs is wrong, they are not blinking when there is traffic. + * To fix this it is required to set extended LED mode + */ + ret = lanphy_modify_page_reg(phydev, LAN8814_PAGE_PORT_REGS, + LAN8814_LED_CTRL_1, + LAN8814_LED_CTRL_1_KSZ9031_LED_MODE_, 0); + if (ret < 0) + return ret; + + ret = lanphy_modify_page_reg(phydev, LAN8814_PAGE_PORT_REGS, + LAN8814_LED_CTRL_2, + LAN8814_LED_CTRL_2_LED1_COM_DIS, + LAN8814_LED_CTRL_2_LED1_COM_DIS); + if (ret < 0) + return ret; + + /* To allow the PHY to control the LEDs the GPIOs of the PHY should have + * a function mode and not the GPIO. Apparently by default the value is + * GPIO and not function even though the datasheet it says that it is + * function. Therefore set this value. + */ + return lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + LAN8814_GPIO_EN2, 0); +} + +#define LAN8842_INTR_CTRL_REG 52 /* 0x34 */ + +static int lan8842_config_intr(struct phy_device *phydev) +{ + int err; + + lanphy_write_page_reg(phydev, LAN8814_PAGE_COMMON_REGS, + LAN8842_INTR_CTRL_REG, + LAN8814_INTR_CTRL_REG_INTR_ENABLE); + + /* enable / disable interrupts */ + if (phydev->interrupts == PHY_INTERRUPT_ENABLED) { + err = lan8814_ack_interrupt(phydev); + if (err) + return err; + + err = phy_write(phydev, LAN8814_INTC, + LAN8814_INT_LINK | LAN8814_INT_FLF); + } else { + err = phy_write(phydev, LAN8814_INTC, 0); + if (err) + return err; + + err = lan8814_ack_interrupt(phydev); + } + + return err; +} + +static unsigned int lan8842_inband_caps(struct phy_device *phydev, + phy_interface_t interface) +{ + /* Inband configuration can be enabled or disabled using the registers + * PCS1G_ANEG_CONFIG. + */ + return LINK_INBAND_DISABLE | LINK_INBAND_ENABLE; +} + +static int lan8842_config_inband(struct phy_device *phydev, unsigned int modes) +{ + bool enable; + + if (modes == LINK_INBAND_DISABLE) + enable = false; + else + enable = true; + + /* Disable or enable in-band autoneg with PCS Host side + * It has the same address as lan8814 + */ + return lanphy_modify_page_reg(phydev, LAN8814_PAGE_PORT_REGS, + LAN8814_QSGMII_PCS1G_ANEG_CONFIG, + LAN8814_QSGMII_PCS1G_ANEG_CONFIG_ANEG_ENA, + enable ? LAN8814_QSGMII_PCS1G_ANEG_CONFIG_ANEG_ENA : 0); +} + +static void lan8842_handle_ptp_interrupt(struct phy_device *phydev, u16 status) +{ + struct kszphy_ptp_priv *ptp_priv; + struct lan8842_priv *priv; + + priv = phydev->priv; + ptp_priv = &priv->ptp_priv; + + if (status & PTP_TSU_INT_STS_PTP_TX_TS_EN_) + lan8814_get_tx_ts(ptp_priv); + + if (status & PTP_TSU_INT_STS_PTP_RX_TS_EN_) + lan8814_get_rx_ts(ptp_priv); + + if (status & PTP_TSU_INT_STS_PTP_TX_TS_OVRFL_INT_) { + lan8814_flush_fifo(phydev, true); + skb_queue_purge(&ptp_priv->tx_queue); + } + + if (status & PTP_TSU_INT_STS_PTP_RX_TS_OVRFL_INT_) { + lan8814_flush_fifo(phydev, false); + skb_queue_purge(&ptp_priv->rx_queue); + } +} + +static irqreturn_t lan8842_handle_interrupt(struct phy_device *phydev) +{ + struct lan8842_priv *priv = phydev->priv; + int ret = IRQ_NONE; + int irq_status; + + irq_status = phy_read(phydev, LAN8814_INTS); + if (irq_status < 0) { + phy_error(phydev); + return IRQ_NONE; + } + + if (irq_status & (LAN8814_INT_LINK | LAN8814_INT_FLF)) { + phy_trigger_machine(phydev); + ret = IRQ_HANDLED; + } + + /* Phy revision lan8832 doesn't have support for PTP therefore there is + * not need to check the PTP and GPIO interrupts + */ + if (priv->rev == LAN8842_REV_8832) + goto out; + + while (true) { + irq_status = lanphy_read_page_reg(phydev, LAN8814_PAGE_PORT_REGS, + PTP_TSU_INT_STS); + if (!irq_status) + break; + + lan8842_handle_ptp_interrupt(phydev, irq_status); + ret = IRQ_HANDLED; + } + + if (!lan8814_handle_gpio_interrupt(phydev, irq_status)) + ret = IRQ_HANDLED; + +out: + return ret; +} + +static u64 lan8842_get_stat(struct phy_device *phydev, int count, int *regs) +{ + u64 ret = 0; + int val; + + for (int j = 0; j < count; ++j) { + val = lanphy_read_page_reg(phydev, LAN8814_PAGE_PCS_DIGITAL, + regs[j]); + if (val < 0) + return U64_MAX; + + ret <<= 16; + ret += val; + } + return ret; +} + +static int lan8842_update_stats(struct phy_device *phydev) +{ + struct lan8842_priv *priv = phydev->priv; + int rx_packets_regs[] = {88, 61, 60}; + int rx_errors_regs[] = {63, 62}; + int tx_packets_regs[] = {89, 85, 84}; + int tx_errors_regs[] = {87, 86}; + + priv->phy_stats.rx_packets = lan8842_get_stat(phydev, + ARRAY_SIZE(rx_packets_regs), + rx_packets_regs); + priv->phy_stats.rx_errors = lan8842_get_stat(phydev, + ARRAY_SIZE(rx_errors_regs), + rx_errors_regs); + priv->phy_stats.tx_packets = lan8842_get_stat(phydev, + ARRAY_SIZE(tx_packets_regs), + tx_packets_regs); + priv->phy_stats.tx_errors = lan8842_get_stat(phydev, + ARRAY_SIZE(tx_errors_regs), + tx_errors_regs); + + return 0; +} + +#define LAN8842_FLF 15 /* 0x0e */ +#define LAN8842_FLF_ENA BIT(1) +#define LAN8842_FLF_ENA_LINK_DOWN BIT(0) + +static int lan8842_get_fast_down(struct phy_device *phydev, u8 *msecs) +{ + int ret; + + ret = lanphy_read_page_reg(phydev, LAN8814_PAGE_PCS, LAN8842_FLF); + if (ret < 0) + return ret; + + if (ret & LAN8842_FLF_ENA) + *msecs = ETHTOOL_PHY_FAST_LINK_DOWN_ON; + else + *msecs = ETHTOOL_PHY_FAST_LINK_DOWN_OFF; + + return 0; +} + +static int lan8842_set_fast_down(struct phy_device *phydev, const u8 *msecs) +{ + u16 flf; + + switch (*msecs) { + case ETHTOOL_PHY_FAST_LINK_DOWN_OFF: + flf = 0; + break; + case ETHTOOL_PHY_FAST_LINK_DOWN_ON: + flf = LAN8842_FLF_ENA | LAN8842_FLF_ENA_LINK_DOWN; + break; + default: + return -EINVAL; + } + + return lanphy_modify_page_reg(phydev, LAN8814_PAGE_PCS, + LAN8842_FLF, + LAN8842_FLF_ENA | + LAN8842_FLF_ENA_LINK_DOWN, flf); +} + +static int lan8842_get_tunable(struct phy_device *phydev, + struct ethtool_tunable *tuna, void *data) +{ + switch (tuna->id) { + case ETHTOOL_PHY_FAST_LINK_DOWN: + return lan8842_get_fast_down(phydev, data); + default: + return -EOPNOTSUPP; + } +} + +static int lan8842_set_tunable(struct phy_device *phydev, + struct ethtool_tunable *tuna, const void *data) +{ + switch (tuna->id) { + case ETHTOOL_PHY_FAST_LINK_DOWN: + return lan8842_set_fast_down(phydev, data); + default: + return -EOPNOTSUPP; + } +} + +static void lan8842_get_phy_stats(struct phy_device *phydev, + struct ethtool_eth_phy_stats *eth_stats, + struct ethtool_phy_stats *stats) +{ + struct lan8842_priv *priv = phydev->priv; + + stats->rx_packets = priv->phy_stats.rx_packets; + stats->rx_errors = priv->phy_stats.rx_errors; + stats->tx_packets = priv->phy_stats.tx_packets; + stats->tx_errors = priv->phy_stats.tx_errors; +} + static struct phy_driver ksphy_driver[] = { { - .phy_id = PHY_ID_KS8737, - .phy_id_mask = MICREL_PHY_ID_MASK, + PHY_ID_MATCH_MODEL(PHY_ID_KS8737), .name = "Micrel KS8737", /* PHY_BASIC_FEATURES */ .driver_data = &ks8737_type, @@ -3204,8 +6513,7 @@ static struct phy_driver ksphy_driver[] = { .suspend = kszphy_suspend, .resume = kszphy_resume, }, { - .phy_id = PHY_ID_KSZ8041, - .phy_id_mask = MICREL_PHY_ID_MASK, + PHY_ID_MATCH_MODEL(PHY_ID_KSZ8041), .name = "Micrel KSZ8041", /* PHY_BASIC_FEATURES */ .driver_data = &ksz8041_type, @@ -3217,12 +6525,10 @@ static struct phy_driver ksphy_driver[] = { .get_sset_count = kszphy_get_sset_count, .get_strings = kszphy_get_strings, .get_stats = kszphy_get_stats, - /* No suspend/resume callbacks because of errata DS80000700A, - * receiver error following software power down. - */ + .suspend = ksz8041_suspend, + .resume = ksz8041_resume, }, { - .phy_id = PHY_ID_KSZ8041RNLI, - .phy_id_mask = MICREL_PHY_ID_MASK, + PHY_ID_MATCH_MODEL(PHY_ID_KSZ8041RNLI), .name = "Micrel KSZ8041RNLI", /* PHY_BASIC_FEATURES */ .driver_data = &ksz8041_type, @@ -3265,9 +6571,8 @@ static struct phy_driver ksphy_driver[] = { .suspend = kszphy_suspend, .resume = kszphy_resume, }, { - .phy_id = PHY_ID_KSZ8081, + PHY_ID_MATCH_MODEL(PHY_ID_KSZ8081), .name = "Micrel KSZ8081 or KSZ8091", - .phy_id_mask = MICREL_PHY_ID_MASK, .flags = PHY_POLL_CABLE_TEST, /* PHY_BASIC_FEATURES */ .driver_data = &ksz8081_type, @@ -3286,16 +6591,16 @@ static struct phy_driver ksphy_driver[] = { .cable_test_start = ksz886x_cable_test_start, .cable_test_get_status = ksz886x_cable_test_get_status, }, { - .phy_id = PHY_ID_KSZ8061, + PHY_ID_MATCH_MODEL(PHY_ID_KSZ8061), .name = "Micrel KSZ8061", - .phy_id_mask = MICREL_PHY_ID_MASK, /* PHY_BASIC_FEATURES */ .probe = kszphy_probe, .config_init = ksz8061_config_init, + .soft_reset = genphy_soft_reset, .config_intr = kszphy_config_intr, .handle_interrupt = kszphy_handle_interrupt, - .suspend = kszphy_suspend, - .resume = kszphy_resume, + .suspend = ksz8061_suspend, + .resume = ksz8061_resume, }, { .phy_id = PHY_ID_KSZ9021, .phy_id_mask = 0x000ffffe, @@ -3315,8 +6620,7 @@ static struct phy_driver ksphy_driver[] = { .read_mmd = genphy_read_mmd_unsupported, .write_mmd = genphy_write_mmd_unsupported, }, { - .phy_id = PHY_ID_KSZ9031, - .phy_id_mask = MICREL_PHY_ID_MASK, + PHY_ID_MATCH_MODEL(PHY_ID_KSZ9031), .name = "Micrel KSZ9031 Gigabit PHY", .flags = PHY_POLL_CABLE_TEST, .driver_data = &ksz9021_type, @@ -3334,9 +6638,9 @@ static struct phy_driver ksphy_driver[] = { .resume = kszphy_resume, .cable_test_start = ksz9x31_cable_test_start, .cable_test_get_status = ksz9x31_cable_test_get_status, + .set_loopback = ksz9031_set_loopback, }, { - .phy_id = PHY_ID_LAN8814, - .phy_id_mask = MICREL_PHY_ID_MASK, + PHY_ID_MATCH_MODEL(PHY_ID_LAN8814), .name = "Microchip INDY Gigabit Quad PHY", .flags = PHY_POLL_CABLE_TEST, .config_init = lan8814_config_init, @@ -3350,12 +6654,13 @@ static struct phy_driver ksphy_driver[] = { .suspend = genphy_suspend, .resume = kszphy_resume, .config_intr = lan8814_config_intr, + .inband_caps = lan8842_inband_caps, + .config_inband = lan8842_config_inband, .handle_interrupt = lan8814_handle_interrupt, .cable_test_start = lan8814_cable_test_start, .cable_test_get_status = ksz886x_cable_test_get_status, }, { - .phy_id = PHY_ID_LAN8804, - .phy_id_mask = MICREL_PHY_ID_MASK, + PHY_ID_MATCH_MODEL(PHY_ID_LAN8804), .name = "Microchip LAN966X Gigabit PHY", .config_init = lan8804_config_init, .driver_data = &ksz9021_type, @@ -3365,18 +6670,52 @@ static struct phy_driver ksphy_driver[] = { .get_sset_count = kszphy_get_sset_count, .get_strings = kszphy_get_strings, .get_stats = kszphy_get_stats, - .suspend = genphy_suspend, - .resume = kszphy_resume, + .suspend = lan8804_suspend, + .resume = lan8804_resume, .config_intr = lan8804_config_intr, .handle_interrupt = lan8804_handle_interrupt, }, { - .phy_id = PHY_ID_KSZ9131, - .phy_id_mask = MICREL_PHY_ID_MASK, + PHY_ID_MATCH_MODEL(PHY_ID_LAN8841), + .name = "Microchip LAN8841 Gigabit PHY", + .flags = PHY_POLL_CABLE_TEST, + .driver_data = &lan8841_type, + .config_init = lan8841_config_init, + .probe = lan8841_probe, + .soft_reset = genphy_soft_reset, + .config_intr = lan8841_config_intr, + .handle_interrupt = lan8841_handle_interrupt, + .get_sset_count = kszphy_get_sset_count, + .get_strings = kszphy_get_strings, + .get_stats = kszphy_get_stats, + .suspend = lan8841_suspend, + .resume = lan8841_resume, + .cable_test_start = lan8814_cable_test_start, + .cable_test_get_status = ksz886x_cable_test_get_status, +}, { + PHY_ID_MATCH_MODEL(PHY_ID_LAN8842), + .name = "Microchip LAN8842 Gigabit PHY", + .flags = PHY_POLL_CABLE_TEST, + .driver_data = &lan8814_type, + .probe = lan8842_probe, + .config_init = lan8842_config_init, + .config_intr = lan8842_config_intr, + .inband_caps = lan8842_inband_caps, + .config_inband = lan8842_config_inband, + .handle_interrupt = lan8842_handle_interrupt, + .get_phy_stats = lan8842_get_phy_stats, + .update_stats = lan8842_update_stats, + .get_tunable = lan8842_get_tunable, + .set_tunable = lan8842_set_tunable, + .cable_test_start = lan8814_cable_test_start, + .cable_test_get_status = ksz886x_cable_test_get_status, +}, { + PHY_ID_MATCH_MODEL(PHY_ID_KSZ9131), .name = "Microchip KSZ9131 Gigabit PHY", /* PHY_GBIT_FEATURES */ .flags = PHY_POLL_CABLE_TEST, - .driver_data = &ksz9021_type, + .driver_data = &ksz9131_type, .probe = kszphy_probe, + .soft_reset = genphy_soft_reset, .config_init = ksz9131_config_init, .config_intr = kszphy_config_intr, .config_aneg = ksz9131_config_aneg, @@ -3386,12 +6725,12 @@ static struct phy_driver ksphy_driver[] = { .get_strings = kszphy_get_strings, .get_stats = kszphy_get_stats, .suspend = kszphy_suspend, - .resume = kszphy_resume, + .resume = ksz9131_resume, .cable_test_start = ksz9x31_cable_test_start, .cable_test_get_status = ksz9x31_cable_test_get_status, + .get_features = ksz9477_get_features, }, { - .phy_id = PHY_ID_KSZ8873MLL, - .phy_id_mask = MICREL_PHY_ID_MASK, + PHY_ID_MATCH_MODEL(PHY_ID_KSZ8873MLL), .name = "Micrel KSZ8873MLL Switch", /* PHY_BASIC_FEATURES */ .config_init = kszphy_config_init, @@ -3400,8 +6739,7 @@ static struct phy_driver ksphy_driver[] = { .suspend = genphy_suspend, .resume = genphy_resume, }, { - .phy_id = PHY_ID_KSZ886X, - .phy_id_mask = MICREL_PHY_ID_MASK, + PHY_ID_MATCH_MODEL(PHY_ID_KSZ886X), .name = "Micrel KSZ8851 Ethernet MAC or KSZ886X Switch", .driver_data = &ksz886x_type, /* PHY_BASIC_FEATURES */ @@ -3421,15 +6759,25 @@ static struct phy_driver ksphy_driver[] = { .suspend = genphy_suspend, .resume = genphy_resume, }, { - .phy_id = PHY_ID_KSZ9477, - .phy_id_mask = MICREL_PHY_ID_MASK, + PHY_ID_MATCH_MODEL(PHY_ID_KSZ9477), .name = "Microchip KSZ9477", + .probe = kszphy_probe, /* PHY_GBIT_FEATURES */ - .config_init = kszphy_config_init, + .config_init = ksz9477_config_init, .config_intr = kszphy_config_intr, + .config_aneg = ksz9477_config_aneg, + .read_status = ksz9477_read_status, .handle_interrupt = kszphy_handle_interrupt, .suspend = genphy_suspend, - .resume = genphy_resume, + .resume = ksz9477_resume, + .get_phy_stats = kszphy_get_phy_stats, + .update_stats = kszphy_update_stats, + .cable_test_start = ksz9x31_cable_test_start, + .cable_test_get_status = ksz9x31_cable_test_get_status, + .get_sqi = kszphy_get_sqi, + .get_sqi_max = kszphy_get_sqi_max, + .get_mse_capability = kszphy_get_mse_capability, + .get_mse_snapshot = kszphy_get_mse_snapshot, } }; module_phy_driver(ksphy_driver); @@ -3438,22 +6786,26 @@ MODULE_DESCRIPTION("Micrel PHY driver"); MODULE_AUTHOR("David J. Choi"); MODULE_LICENSE("GPL"); -static struct mdio_device_id __maybe_unused micrel_tbl[] = { +static const struct mdio_device_id __maybe_unused micrel_tbl[] = { { PHY_ID_KSZ9021, 0x000ffffe }, - { PHY_ID_KSZ9031, MICREL_PHY_ID_MASK }, - { PHY_ID_KSZ9131, MICREL_PHY_ID_MASK }, + { PHY_ID_MATCH_MODEL(PHY_ID_KSZ9031) }, + { PHY_ID_MATCH_MODEL(PHY_ID_KSZ9131) }, { PHY_ID_KSZ8001, 0x00fffffc }, - { PHY_ID_KS8737, MICREL_PHY_ID_MASK }, + { PHY_ID_MATCH_MODEL(PHY_ID_KS8737) }, { PHY_ID_KSZ8021, 0x00ffffff }, { PHY_ID_KSZ8031, 0x00ffffff }, - { PHY_ID_KSZ8041, MICREL_PHY_ID_MASK }, - { PHY_ID_KSZ8051, MICREL_PHY_ID_MASK }, - { PHY_ID_KSZ8061, MICREL_PHY_ID_MASK }, - { PHY_ID_KSZ8081, MICREL_PHY_ID_MASK }, - { PHY_ID_KSZ8873MLL, MICREL_PHY_ID_MASK }, - { PHY_ID_KSZ886X, MICREL_PHY_ID_MASK }, - { PHY_ID_LAN8814, MICREL_PHY_ID_MASK }, - { PHY_ID_LAN8804, MICREL_PHY_ID_MASK }, + { PHY_ID_MATCH_MODEL(PHY_ID_KSZ8041) }, + { PHY_ID_MATCH_MODEL(PHY_ID_KSZ8041RNLI) }, + { PHY_ID_MATCH_MODEL(PHY_ID_KSZ8051) }, + { PHY_ID_MATCH_MODEL(PHY_ID_KSZ8061) }, + { PHY_ID_MATCH_MODEL(PHY_ID_KSZ8081) }, + { PHY_ID_MATCH_MODEL(PHY_ID_KSZ8873MLL) }, + { PHY_ID_MATCH_MODEL(PHY_ID_KSZ886X) }, + { PHY_ID_MATCH_MODEL(PHY_ID_KSZ9477) }, + { PHY_ID_MATCH_MODEL(PHY_ID_LAN8814) }, + { PHY_ID_MATCH_MODEL(PHY_ID_LAN8804) }, + { PHY_ID_MATCH_MODEL(PHY_ID_LAN8841) }, + { PHY_ID_MATCH_MODEL(PHY_ID_LAN8842) }, { } }; |