summaryrefslogtreecommitdiff
path: root/drivers/net/tokenring/tms380tr.h
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/tokenring/tms380tr.h')
-rw-r--r--drivers/net/tokenring/tms380tr.h1141
1 files changed, 1141 insertions, 0 deletions
diff --git a/drivers/net/tokenring/tms380tr.h b/drivers/net/tokenring/tms380tr.h
new file mode 100644
index 000000000000..f2c5ba0f37a5
--- /dev/null
+++ b/drivers/net/tokenring/tms380tr.h
@@ -0,0 +1,1141 @@
+/*
+ * tms380tr.h: TI TMS380 Token Ring driver for Linux
+ *
+ * Authors:
+ * - Christoph Goos <cgoos@syskonnect.de>
+ * - Adam Fritzler <mid@auk.cx>
+ */
+
+#ifndef __LINUX_TMS380TR_H
+#define __LINUX_TMS380TR_H
+
+#ifdef __KERNEL__
+
+#include <linux/interrupt.h>
+
+/* module prototypes */
+int tms380tr_open(struct net_device *dev);
+int tms380tr_close(struct net_device *dev);
+irqreturn_t tms380tr_interrupt(int irq, void *dev_id, struct pt_regs *regs);
+int tmsdev_init(struct net_device *dev, unsigned long dmalimit,
+ struct pci_dev *pdev);
+void tmsdev_term(struct net_device *dev);
+void tms380tr_wait(unsigned long time);
+
+#define TMS380TR_MAX_ADAPTERS 7
+
+#define SEND_TIMEOUT 10*HZ
+
+#define TR_RCF_LONGEST_FRAME_MASK 0x0070
+#define TR_RCF_FRAME4K 0x0030
+
+/*------------------------------------------------------------------*/
+/* Bit order for adapter communication with DMA */
+/* -------------------------------------------------------------- */
+/* Bit 8 | 9| 10| 11|| 12| 13| 14| 15|| 0| 1| 2| 3|| 4| 5| 6| 7| */
+/* -------------------------------------------------------------- */
+/* The bytes in a word must be byte swapped. Also, if a double */
+/* word is used for storage, then the words, as well as the bytes, */
+/* must be swapped. */
+/* Bit order for adapter communication with DIO */
+/* -------------------------------------------------------------- */
+/* Bit 0 | 1| 2| 3|| 4| 5| 6| 7|| 8| 9| 10| 11|| 12| 13| 14| 15| */
+/* -------------------------------------------------------------- */
+/*------------------------------------------------------------------*/
+
+/* Swap words of a long. */
+#define SWAPW(x) (((x) << 16) | ((x) >> 16))
+
+/* Get the low byte of a word. */
+#define LOBYTE(w) ((unsigned char)(w))
+
+/* Get the high byte of a word. */
+#define HIBYTE(w) ((unsigned char)((unsigned short)(w) >> 8))
+
+/* Get the low word of a long. */
+#define LOWORD(l) ((unsigned short)(l))
+
+/* Get the high word of a long. */
+#define HIWORD(l) ((unsigned short)((unsigned long)(l) >> 16))
+
+
+
+/* Token ring adapter I/O addresses for normal mode. */
+
+/*
+ * The SIF registers. Common to all adapters.
+ */
+/* Basic SIF (SRSX = 0) */
+#define SIFDAT 0x00 /* SIF/DMA data. */
+#define SIFINC 0x02 /* IO Word data with auto increment. */
+#define SIFINH 0x03 /* IO Byte data with auto increment. */
+#define SIFADR 0x04 /* SIF/DMA Address. */
+#define SIFCMD 0x06 /* SIF Command. */
+#define SIFSTS 0x06 /* SIF Status. */
+
+/* "Extended" SIF (SRSX = 1) */
+#define SIFACL 0x08 /* SIF Adapter Control Register. */
+#define SIFADD 0x0a /* SIF/DMA Address. -- 0x0a */
+#define SIFADX 0x0c /* 0x0c */
+#define DMALEN 0x0e /* SIF DMA length. -- 0x0e */
+
+/*
+ * POS Registers. Only for ISA Adapters.
+ */
+#define POSREG 0x10 /* Adapter Program Option Select (POS)
+ * Register: base IO address + 16 byte.
+ */
+#define POSREG_2 24L /* only for TR4/16+ adapter
+ * base IO address + 24 byte. -- 0x18
+ */
+
+/* SIFCMD command codes (high-low) */
+#define CMD_INTERRUPT_ADAPTER 0x8000 /* Cause internal adapter interrupt */
+#define CMD_ADAPTER_RESET 0x4000 /* Hardware reset of adapter */
+#define CMD_SSB_CLEAR 0x2000 /* Acknowledge to adapter to
+ * system interrupts.
+ */
+#define CMD_EXECUTE 0x1000 /* Execute SCB command */
+#define CMD_SCB_REQUEST 0x0800 /* Request adapter to interrupt
+ * system when SCB is available for
+ * another command.
+ */
+#define CMD_RX_CONTINUE 0x0400 /* Continue receive after odd pointer
+ * stop. (odd pointer receive method)
+ */
+#define CMD_RX_VALID 0x0200 /* Now actual RPL is valid. */
+#define CMD_TX_VALID 0x0100 /* Now actual TPL is valid. (valid
+ * bit receive/transmit method)
+ */
+#define CMD_SYSTEM_IRQ 0x0080 /* Adapter-to-attached-system
+ * interrupt is reset.
+ */
+#define CMD_CLEAR_SYSTEM_IRQ 0x0080 /* Clear SYSTEM_INTERRUPT bit.
+ * (write: 1=ignore, 0=reset)
+ */
+#define EXEC_SOFT_RESET 0xFF00 /* adapter soft reset. (restart
+ * adapter after hardware reset)
+ */
+
+
+/* ACL commands (high-low) */
+#define ACL_SWHLDA 0x0800 /* Software hold acknowledge. */
+#define ACL_SWDDIR 0x0400 /* Data transfer direction. */
+#define ACL_SWHRQ 0x0200 /* Pseudo DMA operation. */
+#define ACL_PSDMAEN 0x0100 /* Enable pseudo system DMA. */
+#define ACL_ARESET 0x0080 /* Adapter hardware reset command.
+ * (held in reset condition as
+ * long as bit is set)
+ */
+#define ACL_CPHALT 0x0040 /* Communication processor halt.
+ * (can only be set while ACL_ARESET
+ * bit is set; prevents adapter
+ * processor from executing code while
+ * downloading firmware)
+ */
+#define ACL_BOOT 0x0020
+#define ACL_SINTEN 0x0008 /* System interrupt enable/disable
+ * (1/0): can be written if ACL_ARESET
+ * is zero.
+ */
+#define ACL_PEN 0x0004
+
+#define ACL_NSELOUT0 0x0002
+#define ACL_NSELOUT1 0x0001 /* NSELOUTx have a card-specific
+ * meaning for setting ring speed.
+ */
+
+#define PS_DMA_MASK (ACL_SWHRQ | ACL_PSDMAEN)
+
+
+/* SIFSTS register return codes (high-low) */
+#define STS_SYSTEM_IRQ 0x0080 /* Adapter-to-attached-system
+ * interrupt is valid.
+ */
+#define STS_INITIALIZE 0x0040 /* INITIALIZE status. (ready to
+ * initialize)
+ */
+#define STS_TEST 0x0020 /* TEST status. (BUD not completed) */
+#define STS_ERROR 0x0010 /* ERROR status. (unrecoverable
+ * HW error occurred)
+ */
+#define STS_MASK 0x00F0 /* Mask interesting status bits. */
+#define STS_ERROR_MASK 0x000F /* Get Error Code by masking the
+ * interrupt code bits.
+ */
+#define ADAPTER_INT_PTRS 0x0A00 /* Address offset of adapter internal
+ * pointers 01:0a00 (high-low) have to
+ * be read after init and before open.
+ */
+
+
+/* Interrupt Codes (only MAC IRQs) */
+#define STS_IRQ_ADAPTER_CHECK 0x0000 /* unrecoverable hardware or
+ * software error.
+ */
+#define STS_IRQ_RING_STATUS 0x0004 /* SSB is updated with ring status. */
+#define STS_IRQ_LLC_STATUS 0x0005 /* Not used in MAC-only microcode */
+#define STS_IRQ_SCB_CLEAR 0x0006 /* SCB clear, following an
+ * SCB_REQUEST IRQ.
+ */
+#define STS_IRQ_TIMER 0x0007 /* Not normally used in MAC ucode */
+#define STS_IRQ_COMMAND_STATUS 0x0008 /* SSB is updated with command
+ * status.
+ */
+#define STS_IRQ_RECEIVE_STATUS 0x000A /* SSB is updated with receive
+ * status.
+ */
+#define STS_IRQ_TRANSMIT_STATUS 0x000C /* SSB is updated with transmit
+ * status
+ */
+#define STS_IRQ_RECEIVE_PENDING 0x000E /* Not used in MAC-only microcode */
+#define STS_IRQ_MASK 0x000F /* = STS_ERROR_MASK. */
+
+
+/* TRANSMIT_STATUS completion code: (SSB.Parm[0]) */
+#define COMMAND_COMPLETE 0x0080 /* TRANSMIT command completed
+ * (avoid this!) issue another transmit
+ * to send additional frames.
+ */
+#define FRAME_COMPLETE 0x0040 /* Frame has been transmitted;
+ * INTERRUPT_FRAME bit was set in the
+ * CSTAT request; indication of possibly
+ * more than one frame transmissions!
+ * SSB.Parm[0-1]: 32 bit pointer to
+ * TPL of last frame.
+ */
+#define LIST_ERROR 0x0020 /* Error in one of the TPLs that
+ * compose the frame; TRANSMIT
+ * terminated; Parm[1-2]: 32bit pointer
+ * to TPL which starts the error
+ * frame; error details in bits 8-13.
+ * (14?)
+ */
+#define FRAME_SIZE_ERROR 0x8000 /* FRAME_SIZE does not equal the sum of
+ * the valid DATA_COUNT fields;
+ * FRAME_SIZE less than header plus
+ * information field. (15 bytes +
+ * routing field) Or if FRAME_SIZE
+ * was specified as zero in one list.
+ */
+#define TX_THRESHOLD 0x4000 /* FRAME_SIZE greater than (BUFFER_SIZE
+ * - 9) * TX_BUF_MAX.
+ */
+#define ODD_ADDRESS 0x2000 /* Odd forward pointer value is
+ * read on a list without END_FRAME
+ * indication.
+ */
+#define FRAME_ERROR 0x1000 /* START_FRAME bit (not) anticipated,
+ * but (not) set.
+ */
+#define ACCESS_PRIORITY_ERROR 0x0800 /* Access priority requested has not
+ * been allowed.
+ */
+#define UNENABLED_MAC_FRAME 0x0400 /* MAC frame has source class of zero
+ * or MAC frame PCF ATTN field is
+ * greater than one.
+ */
+#define ILLEGAL_FRAME_FORMAT 0x0200 /* Bit 0 or FC field was set to one. */
+
+
+/*
+ * Since we need to support some functions even if the adapter is in a
+ * CLOSED state, we have a (pseudo-) command queue which holds commands
+ * that are outstandig to be executed.
+ *
+ * Each time a command completes, an interrupt occurs and the next
+ * command is executed. The command queue is actually a simple word with
+ * a bit for each outstandig command. Therefore the commands will not be
+ * executed in the order they have been queued.
+ *
+ * The following defines the command code bits and the command queue:
+ */
+#define OC_OPEN 0x0001 /* OPEN command */
+#define OC_TRANSMIT 0x0002 /* TRANSMIT command */
+#define OC_TRANSMIT_HALT 0x0004 /* TRANSMIT_HALT command */
+#define OC_RECEIVE 0x0008 /* RECEIVE command */
+#define OC_CLOSE 0x0010 /* CLOSE command */
+#define OC_SET_GROUP_ADDR 0x0020 /* SET_GROUP_ADDR command */
+#define OC_SET_FUNCT_ADDR 0x0040 /* SET_FUNCT_ADDR command */
+#define OC_READ_ERROR_LOG 0x0080 /* READ_ERROR_LOG command */
+#define OC_READ_ADAPTER 0x0100 /* READ_ADAPTER command */
+#define OC_MODIFY_OPEN_PARMS 0x0400 /* MODIFY_OPEN_PARMS command */
+#define OC_RESTORE_OPEN_PARMS 0x0800 /* RESTORE_OPEN_PARMS command */
+#define OC_SET_FIRST_16_GROUP 0x1000 /* SET_FIRST_16_GROUP command */
+#define OC_SET_BRIDGE_PARMS 0x2000 /* SET_BRIDGE_PARMS command */
+#define OC_CONFIG_BRIDGE_PARMS 0x4000 /* CONFIG_BRIDGE_PARMS command */
+
+#define OPEN 0x0300 /* C: open command. S: completion. */
+#define TRANSMIT 0x0400 /* C: transmit command. S: completion
+ * status. (reject: COMMAND_REJECT if
+ * adapter not opened, TRANSMIT already
+ * issued or address passed in the SCB
+ * not word aligned)
+ */
+#define TRANSMIT_HALT 0x0500 /* C: interrupt TX TPL chain; if no
+ * TRANSMIT command issued, the command
+ * is ignored (completion with TRANSMIT
+ * status (0x0400)!)
+ */
+#define RECEIVE 0x0600 /* C: receive command. S: completion
+ * status. (reject: COMMAND_REJECT if
+ * adapter not opened, RECEIVE already
+ * issued or address passed in the SCB
+ * not word aligned)
+ */
+#define CLOSE 0x0700 /* C: close adapter. S: completion.
+ * (COMMAND_REJECT if adapter not open)
+ */
+#define SET_GROUP_ADDR 0x0800 /* C: alter adapter group address after
+ * OPEN. S: completion. (COMMAND_REJECT
+ * if adapter not open)
+ */
+#define SET_FUNCT_ADDR 0x0900 /* C: alter adapter functional address
+ * after OPEN. S: completion.
+ * (COMMAND_REJECT if adapter not open)
+ */
+#define READ_ERROR_LOG 0x0A00 /* C: read adapter error counters.
+ * S: completion. (command ignored
+ * if adapter not open!)
+ */
+#define READ_ADAPTER 0x0B00 /* C: read data from adapter memory.
+ * (important: after init and before
+ * open!) S: completion. (ADAPTER_CHECK
+ * interrupt if undefined storage area
+ * read)
+ */
+#define MODIFY_OPEN_PARMS 0x0D00 /* C: modify some adapter operational
+ * parameters. (bit correspondend to
+ * WRAP_INTERFACE is ignored)
+ * S: completion. (reject:
+ * COMMAND_REJECT)
+ */
+#define RESTORE_OPEN_PARMS 0x0E00 /* C: modify some adapter operational
+ * parameters. (bit correspondend
+ * to WRAP_INTERFACE is ignored)
+ * S: completion. (reject:
+ * COMMAND_REJECT)
+ */
+#define SET_FIRST_16_GROUP 0x0F00 /* C: alter the first two bytes in
+ * adapter group address.
+ * S: completion. (reject:
+ * COMMAND_REJECT)
+ */
+#define SET_BRIDGE_PARMS 0x1000 /* C: values and conditions for the
+ * adapter hardware to use when frames
+ * are copied for forwarding.
+ * S: completion. (reject:
+ * COMMAND_REJECT)
+ */
+#define CONFIG_BRIDGE_PARMS 0x1100 /* C: ..
+ * S: completion. (reject:
+ * COMMAND_REJECT)
+ */
+
+#define SPEED_4 4
+#define SPEED_16 16 /* Default transmission speed */
+
+
+/* Initialization Parameter Block (IPB); word alignment necessary! */
+#define BURST_SIZE 0x0018 /* Default burst size */
+#define BURST_MODE 0x9F00 /* Burst mode enable */
+#define DMA_RETRIES 0x0505 /* Magic DMA retry number... */
+
+#define CYCLE_TIME 3 /* Default AT-bus cycle time: 500 ns
+ * (later adapter version: fix cycle time!)
+ */
+#define LINE_SPEED_BIT 0x80
+
+/* Macro definition for the wait function. */
+#define ONE_SECOND_TICKS 1000000
+#define HALF_SECOND (ONE_SECOND_TICKS / 2)
+#define ONE_SECOND (ONE_SECOND_TICKS)
+#define TWO_SECONDS (ONE_SECOND_TICKS * 2)
+#define THREE_SECONDS (ONE_SECOND_TICKS * 3)
+#define FOUR_SECONDS (ONE_SECOND_TICKS * 4)
+#define FIVE_SECONDS (ONE_SECOND_TICKS * 5)
+
+#define BUFFER_SIZE 2048 /* Buffers on Adapter */
+
+#pragma pack(1)
+typedef struct {
+ unsigned short Init_Options; /* Initialize with burst mode;
+ * LLC disabled. (MAC only)
+ */
+
+ /* Interrupt vectors the adapter places on attached system bus. */
+ u_int8_t CMD_Status_IV; /* Interrupt vector: command status. */
+ u_int8_t TX_IV; /* Interrupt vector: transmit. */
+ u_int8_t RX_IV; /* Interrupt vector: receive. */
+ u_int8_t Ring_Status_IV; /* Interrupt vector: ring status. */
+ u_int8_t SCB_Clear_IV; /* Interrupt vector: SCB clear. */
+ u_int8_t Adapter_CHK_IV; /* Interrupt vector: adapter check. */
+
+ u_int16_t RX_Burst_Size; /* Max. number of transfer cycles. */
+ u_int16_t TX_Burst_Size; /* During DMA burst; even value! */
+ u_int16_t DMA_Abort_Thrhld; /* Number of DMA retries. */
+
+ u_int32_t SCB_Addr; /* SCB address: even, word aligned, high-low */
+ u_int32_t SSB_Addr; /* SSB address: even, word aligned, high-low */
+} IPB, *IPB_Ptr;
+#pragma pack()
+
+/*
+ * OPEN Command Parameter List (OCPL) (can be reused, if the adapter has to
+ * be reopened)
+ */
+#define BUFFER_SIZE 2048 /* Buffers on Adapter. */
+#define TPL_SIZE 8+6*TX_FRAG_NUM /* Depending on fragments per TPL. */
+#define RPL_SIZE 14 /* (with TI firmware v2.26 handling
+ * up to nine fragments possible)
+ */
+#define TX_BUF_MIN 20 /* ??? (Stephan: calculation with */
+#define TX_BUF_MAX 40 /* BUFFER_SIZE and MAX_FRAME_SIZE) ???
+ */
+#define DISABLE_EARLY_TOKEN_RELEASE 0x1000
+
+/* OPEN Options (high-low) */
+#define WRAP_INTERFACE 0x0080 /* Inserting omitted for test
+ * purposes; transmit data appears
+ * as receive data. (useful for
+ * testing; change: CLOSE necessary)
+ */
+#define DISABLE_HARD_ERROR 0x0040 /* On HARD_ERROR & TRANSMIT_BEACON
+ * no RING.STATUS interrupt.
+ */
+#define DISABLE_SOFT_ERROR 0x0020 /* On SOFT_ERROR, no RING.STATUS
+ * interrupt.
+ */
+#define PASS_ADAPTER_MAC_FRAMES 0x0010 /* Passing unsupported MAC frames
+ * to system.
+ */
+#define PASS_ATTENTION_FRAMES 0x0008 /* All changed attention MAC frames are
+ * passed to the system.
+ */
+#define PAD_ROUTING_FIELD 0x0004 /* Routing field is padded to 18
+ * bytes.
+ */
+#define FRAME_HOLD 0x0002 /*Adapter waits for entire frame before
+ * initiating DMA transfer; otherwise:
+ * DMA transfer initiation if internal
+ * buffer filled.
+ */
+#define CONTENDER 0x0001 /* Adapter participates in the monitor
+ * contention process.
+ */
+#define PASS_BEACON_MAC_FRAMES 0x8000 /* Adapter passes beacon MAC frames
+ * to the system.
+ */
+#define EARLY_TOKEN_RELEASE 0x1000 /* Only valid in 16 Mbps operation;
+ * 0 = ETR. (no effect in 4 Mbps
+ * operation)
+ */
+#define COPY_ALL_MAC_FRAMES 0x0400 /* All MAC frames are copied to
+ * the system. (after OPEN: duplicate
+ * address test (DAT) MAC frame is
+ * first received frame copied to the
+ * system)
+ */
+#define COPY_ALL_NON_MAC_FRAMES 0x0200 /* All non MAC frames are copied to
+ * the system.
+ */
+#define PASS_FIRST_BUF_ONLY 0x0100 /* Passes only first internal buffer
+ * of each received frame; FrameSize
+ * of RPLs must contain internal
+ * BUFFER_SIZE bits for promiscous mode.
+ */
+#define ENABLE_FULL_DUPLEX_SELECTION 0x2000
+ /* Enable the use of full-duplex
+ * settings with bits in byte 22 in
+ * ocpl. (new feature in firmware
+ * version 3.09)
+ */
+
+/* Full-duplex settings */
+#define OPEN_FULL_DUPLEX_OFF 0x0000
+#define OPEN_FULL_DUPLEX_ON 0x00c0
+#define OPEN_FULL_DUPLEX_AUTO 0x0080
+
+#define PROD_ID_SIZE 18 /* Length of product ID. */
+
+#define TX_FRAG_NUM 3 /* Number of fragments used in one TPL. */
+#define TX_MORE_FRAGMENTS 0x8000 /* Bit set in DataCount to indicate more
+ * fragments following.
+ */
+
+/* XXX is there some better way to do this? */
+#define ISA_MAX_ADDRESS 0x00ffffff
+#define PCI_MAX_ADDRESS 0xffffffff
+
+#pragma pack(1)
+typedef struct {
+ u_int16_t OPENOptions;
+ u_int8_t NodeAddr[6]; /* Adapter node address; use ROM
+ * address
+ */
+ u_int32_t GroupAddr; /* Multicast: high order
+ * bytes = 0xC000
+ */
+ u_int32_t FunctAddr; /* High order bytes = 0xC000 */
+ u_int16_t RxListSize; /* RPL size: 0 (=26), 14, 20 or
+ * 26 bytes read by the adapter.
+ * (Depending on the number of
+ * fragments/list)
+ */
+ u_int16_t TxListSize; /* TPL size */
+ u_int16_t BufSize; /* Is automatically rounded up to the
+ * nearest nK boundary.
+ */
+ u_int16_t FullDuplex;
+ u_int16_t Reserved;
+ u_int8_t TXBufMin; /* Number of adapter buffers reserved
+ * for transmission a minimum of 2
+ * buffers must be allocated.
+ */
+ u_int8_t TXBufMax; /* Maximum number of adapter buffers
+ * for transmit; a minimum of 2 buffers
+ * must be available for receive.
+ * Default: 6
+ */
+ u_int16_t ProdIDAddr[2];/* Pointer to product ID. */
+} OPB, *OPB_Ptr;
+#pragma pack()
+
+/*
+ * SCB: adapter commands enabled by the host system started by writing
+ * CMD_INTERRUPT_ADAPTER | CMD_EXECUTE (|SCB_REQUEST) to the SIFCMD IO
+ * register. (special case: | CMD_SYSTEM_IRQ for initialization)
+ */
+#pragma pack(1)
+typedef struct {
+ u_int16_t CMD; /* Command code */
+ u_int16_t Parm[2]; /* Pointer to Command Parameter Block */
+} SCB; /* System Command Block (32 bit physical address; big endian)*/
+#pragma pack()
+
+/*
+ * SSB: adapter command return status can be evaluated after COMMAND_STATUS
+ * adapter to system interrupt after reading SSB, the availability of the SSB
+ * has to be told the adapter by writing CMD_INTERRUPT_ADAPTER | CMD_SSB_CLEAR
+ * in the SIFCMD IO register.
+ */
+#pragma pack(1)
+typedef struct {
+ u_int16_t STS; /* Status code */
+ u_int16_t Parm[3]; /* Parameter or pointer to Status Parameter
+ * Block.
+ */
+} SSB; /* System Status Block (big endian - physical address) */
+#pragma pack()
+
+typedef struct {
+ unsigned short BurnedInAddrPtr; /* Pointer to adapter burned in
+ * address. (BIA)
+ */
+ unsigned short SoftwareLevelPtr;/* Pointer to software level data. */
+ unsigned short AdapterAddrPtr; /* Pointer to adapter addresses. */
+ unsigned short AdapterParmsPtr; /* Pointer to adapter parameters. */
+ unsigned short MACBufferPtr; /* Pointer to MAC buffer. (internal) */
+ unsigned short LLCCountersPtr; /* Pointer to LLC counters. */
+ unsigned short SpeedFlagPtr; /* Pointer to data rate flag.
+ * (4/16 Mbps)
+ */
+ unsigned short AdapterRAMPtr; /* Pointer to adapter RAM found. (KB) */
+} INTPTRS; /* Adapter internal pointers */
+
+#pragma pack(1)
+typedef struct {
+ u_int8_t Line_Error; /* Line error: code violation in
+ * frame or in a token, or FCS error.
+ */
+ u_int8_t Internal_Error; /* IBM specific. (Reserved_1) */
+ u_int8_t Burst_Error;
+ u_int8_t ARI_FCI_Error; /* ARI/FCI bit zero in AMP or
+ * SMP MAC frame.
+ */
+ u_int8_t AbortDelimeters; /* IBM specific. (Reserved_2) */
+ u_int8_t Reserved_3;
+ u_int8_t Lost_Frame_Error; /* Receive of end of transmitted
+ * frame failed.
+ */
+ u_int8_t Rx_Congest_Error; /* Adapter in repeat mode has not
+ * enough buffer space to copy incoming
+ * frame.
+ */
+ u_int8_t Frame_Copied_Error; /* ARI bit not zero in frame
+ * addressed to adapter.
+ */
+ u_int8_t Frequency_Error; /* IBM specific. (Reserved_4) */
+ u_int8_t Token_Error; /* (active only in monitor station) */
+ u_int8_t Reserved_5;
+ u_int8_t DMA_Bus_Error; /* DMA bus errors not exceeding the
+ * abort thresholds.
+ */
+ u_int8_t DMA_Parity_Error; /* DMA parity errors not exceeding
+ * the abort thresholds.
+ */
+} ERRORTAB; /* Adapter error counters */
+#pragma pack()
+
+
+/*--------------------- Send and Receive definitions -------------------*/
+#pragma pack(1)
+typedef struct {
+ u_int16_t DataCount; /* Value 0, even and odd values are
+ * permitted; value is unaltered most
+ * significant bit set: following
+ * fragments last fragment: most
+ * significant bit is not evaluated.
+ * (???)
+ */
+ u_int32_t DataAddr; /* Pointer to frame data fragment;
+ * even or odd.
+ */
+} Fragment;
+#pragma pack()
+
+#define MAX_FRAG_NUMBERS 9 /* Maximal number of fragments possible to use
+ * in one RPL/TPL. (depending on TI firmware
+ * version)
+ */
+
+/*
+ * AC (1), FC (1), Dst (6), Src (6), RIF (18), Data (4472) = 4504
+ * The packet size can be one of the follows: 548, 1502, 2084, 4504, 8176,
+ * 11439, 17832. Refer to TMS380 Second Generation Token Ring User's Guide
+ * Page 2-27.
+ */
+#define HEADER_SIZE (1 + 1 + 6 + 6)
+#define SRC_SIZE 18
+#define MIN_DATA_SIZE 516
+#define DEFAULT_DATA_SIZE 4472
+#define MAX_DATA_SIZE 17800
+
+#define DEFAULT_PACKET_SIZE (HEADER_SIZE + SRC_SIZE + DEFAULT_DATA_SIZE)
+#define MIN_PACKET_SIZE (HEADER_SIZE + SRC_SIZE + MIN_DATA_SIZE)
+#define MAX_PACKET_SIZE (HEADER_SIZE + SRC_SIZE + MAX_DATA_SIZE)
+
+/*
+ * Macros to deal with the frame status field.
+ */
+#define AC_NOT_RECOGNIZED 0x00
+#define GROUP_BIT 0x80
+#define GET_TRANSMIT_STATUS_HIGH_BYTE(Ts) ((unsigned char)((Ts) >> 8))
+#define GET_FRAME_STATUS_HIGH_AC(Fs) ((unsigned char)(((Fs) & 0xC0) >> 6))
+#define GET_FRAME_STATUS_LOW_AC(Fs) ((unsigned char)(((Fs) & 0x0C) >> 2))
+#define DIRECTED_FRAME(Context) (!((Context)->MData[2] & GROUP_BIT))
+
+
+/*--------------------- Send Functions ---------------------------------*/
+/* define TX_CSTAT _REQUEST (R) and _COMPLETE (C) values (high-low) */
+
+#define TX_VALID 0x0080 /* R: set via TRANSMIT.VALID interrupt.
+ * C: always reset to zero!
+ */
+#define TX_FRAME_COMPLETE 0x0040 /* R: must be reset to zero.
+ * C: set to one.
+ */
+#define TX_START_FRAME 0x0020 /* R: start of a frame: 1
+ * C: unchanged.
+ */
+#define TX_END_FRAME 0x0010 /* R: end of a frame: 1
+ * C: unchanged.
+ */
+#define TX_FRAME_IRQ 0x0008 /* R: request interrupt generation
+ * after transmission.
+ * C: unchanged.
+ */
+#define TX_ERROR 0x0004 /* R: reserved.
+ * C: set to one if Error occurred.
+ */
+#define TX_INTERFRAME_WAIT 0x0004
+#define TX_PASS_CRC 0x0002 /* R: set if CRC value is already
+ * calculated. (valid only in
+ * FRAME_START TPL)
+ * C: unchanged.
+ */
+#define TX_PASS_SRC_ADDR 0x0001 /* R: adapter uses explicit frame
+ * source address and does not overwrite
+ * with the adapter node address.
+ * (valid only in FRAME_START TPL)
+ *
+ * C: unchanged.
+ */
+#define TX_STRIP_FS 0xFF00 /* R: reserved.
+ * C: if no Transmission Error,
+ * field contains copy of FS byte after
+ * stripping of frame.
+ */
+
+/*
+ * Structure of Transmit Parameter Lists (TPLs) (only one frame every TPL,
+ * but possibly multiple TPLs for one frame) the length of the TPLs has to be
+ * initialized in the OPL. (OPEN parameter list)
+ */
+#define TPL_NUM 3 /* Number of Transmit Parameter Lists.
+ * !! MUST BE >= 3 !!
+ */
+
+#pragma pack(1)
+typedef struct s_TPL TPL;
+
+struct s_TPL { /* Transmit Parameter List (align on even word boundaries) */
+ u_int32_t NextTPLAddr; /* Pointer to next TPL in chain; if
+ * pointer is odd: this is the last
+ * TPL. Pointing to itself can cause
+ * problems!
+ */
+ volatile u_int16_t Status; /* Initialized by the adapter:
+ * CSTAT_REQUEST important: update least
+ * significant bit first! Set by the
+ * adapter: CSTAT_COMPLETE status.
+ */
+ u_int16_t FrameSize; /* Number of bytes to be transmitted
+ * as a frame including AC/FC,
+ * Destination, Source, Routing field
+ * not including CRC, FS, End Delimiter
+ * (valid only if START_FRAME bit in
+ * CSTAT nonzero) must not be zero in
+ * any list; maximum value: (BUFFER_SIZE
+ * - 8) * TX_BUF_MAX sum of DataCount
+ * values in FragmentList must equal
+ * Frame_Size value in START_FRAME TPL!
+ * frame data fragment list.
+ */
+
+ /* TPL/RPL size in OPEN parameter list depending on maximal
+ * numbers of fragments used in one parameter list.
+ */
+ Fragment FragList[TX_FRAG_NUM]; /* Maximum: nine frame fragments in one
+ * TPL actual version of firmware: 9
+ * fragments possible.
+ */
+#pragma pack()
+
+ /* Special proprietary data and precalculations */
+
+ TPL *NextTPLPtr; /* Pointer to next TPL in chain. */
+ unsigned char *MData;
+ struct sk_buff *Skb;
+ unsigned char TPLIndex;
+ volatile unsigned char BusyFlag;/* Flag: TPL busy? */
+ dma_addr_t DMABuff; /* DMA IO bus address from pci_map */
+};
+
+/* ---------------------Receive Functions-------------------------------*
+ * define RECEIVE_CSTAT_REQUEST (R) and RECEIVE_CSTAT_COMPLETE (C) values.
+ * (high-low)
+ */
+#define RX_VALID 0x0080 /* R: set; tell adapter with
+ * RECEIVE.VALID interrupt.
+ * C: reset to zero.
+ */
+#define RX_FRAME_COMPLETE 0x0040 /* R: must be reset to zero,
+ * C: set to one.
+ */
+#define RX_START_FRAME 0x0020 /* R: must be reset to zero.
+ * C: set to one on the list.
+ */
+#define RX_END_FRAME 0x0010 /* R: must be reset to zero.
+ * C: set to one on the list
+ * that ends the frame.
+ */
+#define RX_FRAME_IRQ 0x0008 /* R: request interrupt generation
+ * after receive.
+ * C: unchanged.
+ */
+#define RX_INTERFRAME_WAIT 0x0004 /* R: after receiving a frame:
+ * interrupt and wait for a
+ * RECEIVE.CONTINUE.
+ * C: unchanged.
+ */
+#define RX_PASS_CRC 0x0002 /* R: if set, the adapter includes
+ * the CRC in data passed. (last four
+ * bytes; valid only if FRAME_START is
+ * set)
+ * C: set, if CRC is included in
+ * received data.
+ */
+#define RX_PASS_SRC_ADDR 0x0001 /* R: adapter uses explicit frame
+ * source address and does not
+ * overwrite with the adapter node
+ * address. (valid only if FRAME_START
+ * is set)
+ * C: unchanged.
+ */
+#define RX_RECEIVE_FS 0xFC00 /* R: reserved; must be reset to zero.
+ * C: on lists with START_FRAME, field
+ * contains frame status field from
+ * received frame; otherwise cleared.
+ */
+#define RX_ADDR_MATCH 0x0300 /* R: reserved; must be reset to zero.
+ * C: address match code mask.
+ */
+#define RX_STATUS_MASK 0x00FF /* Mask for receive status bits. */
+
+#define RX_INTERN_ADDR_MATCH 0x0100 /* C: internally address match. */
+#define RX_EXTERN_ADDR_MATCH 0x0200 /* C: externally matched via
+ * XMATCH/XFAIL interface.
+ */
+#define RX_INTEXT_ADDR_MATCH 0x0300 /* C: internally and externally
+ * matched.
+ */
+#define RX_READY (RX_VALID | RX_FRAME_IRQ) /* Ready for receive. */
+
+/* Constants for Command Status Interrupt.
+ * COMMAND_REJECT status field bit functions (SSB.Parm[0])
+ */
+#define ILLEGAL_COMMAND 0x0080 /* Set if an unknown command
+ * is issued to the adapter
+ */
+#define ADDRESS_ERROR 0x0040 /* Set if any address field in
+ * the SCB is odd. (not word aligned)
+ */
+#define ADAPTER_OPEN 0x0020 /* Command issued illegal with
+ * open adapter.
+ */
+#define ADAPTER_CLOSE 0x0010 /* Command issued illegal with
+ * closed adapter.
+ */
+#define SAME_COMMAND 0x0008 /* Command issued with same command
+ * already executing.
+ */
+
+/* OPEN_COMPLETION values (SSB.Parm[0], MSB) */
+#define NODE_ADDR_ERROR 0x0040 /* Wrong address or BIA read
+ * zero address.
+ */
+#define LIST_SIZE_ERROR 0x0020 /* If List_Size value not in 0,
+ * 14, 20, 26.
+ */
+#define BUF_SIZE_ERROR 0x0010 /* Not enough available memory for
+ * two buffers.
+ */
+#define TX_BUF_COUNT_ERROR 0x0004 /* Remaining receive buffers less than
+ * two.
+ */
+#define OPEN_ERROR 0x0002 /* Error during ring insertion; more
+ * information in bits 8-15.
+ */
+
+/* Standard return codes */
+#define GOOD_COMPLETION 0x0080 /* =OPEN_SUCCESSFULL */
+#define INVALID_OPEN_OPTION 0x0001 /* OPEN options are not supported by
+ * the adapter.
+ */
+
+/* OPEN phases; details of OPEN_ERROR (SSB.Parm[0], LSB) */
+#define OPEN_PHASES_MASK 0xF000 /* Check only the bits 8-11. */
+#define LOBE_MEDIA_TEST 0x1000
+#define PHYSICAL_INSERTION 0x2000
+#define ADDRESS_VERIFICATION 0x3000
+#define PARTICIPATION_IN_RING_POLL 0x4000
+#define REQUEST_INITIALISATION 0x5000
+#define FULLDUPLEX_CHECK 0x6000
+
+/* OPEN error codes; details of OPEN_ERROR (SSB.Parm[0], LSB) */
+#define OPEN_ERROR_CODES_MASK 0x0F00 /* Check only the bits 12-15. */
+#define OPEN_FUNCTION_FAILURE 0x0100 /* Unable to transmit to itself or
+ * frames received before insertion.
+ */
+#define OPEN_SIGNAL_LOSS 0x0200 /* Signal loss condition detected at
+ * receiver.
+ */
+#define OPEN_TIMEOUT 0x0500 /* Insertion timer expired before
+ * logical insertion.
+ */
+#define OPEN_RING_FAILURE 0x0600 /* Unable to receive own ring purge
+ * MAC frames.
+ */
+#define OPEN_RING_BEACONING 0x0700 /* Beacon MAC frame received after
+ * ring insertion.
+ */
+#define OPEN_DUPLICATE_NODEADDR 0x0800 /* Other station in ring found
+ * with the same address.
+ */
+#define OPEN_REQUEST_INIT 0x0900 /* RPS present but does not respond. */
+#define OPEN_REMOVE_RECEIVED 0x0A00 /* Adapter received a remove adapter
+ * MAC frame.
+ */
+#define OPEN_FULLDUPLEX_SET 0x0D00 /* Got this with full duplex on when
+ * trying to connect to a normal ring.
+ */
+
+/* SET_BRIDGE_PARMS return codes: */
+#define BRIDGE_INVALID_MAX_LEN 0x4000 /* MAX_ROUTING_FIELD_LENGTH odd,
+ * less than 6 or > 30.
+ */
+#define BRIDGE_INVALID_SRC_RING 0x2000 /* SOURCE_RING number zero, too large
+ * or = TARGET_RING.
+ */
+#define BRIDGE_INVALID_TRG_RING 0x1000 /* TARGET_RING number zero, too large
+ * or = SOURCE_RING.
+ */
+#define BRIDGE_INVALID_BRDGE_NO 0x0800 /* BRIDGE_NUMBER too large. */
+#define BRIDGE_INVALID_OPTIONS 0x0400 /* Invalid bridge options. */
+#define BRIDGE_DIAGS_FAILED 0x0200 /* Diagnostics of TMS380SRA failed. */
+#define BRIDGE_NO_SRA 0x0100 /* The TMS380SRA does not exist in HW
+ * configuration.
+ */
+
+/*
+ * Bring Up Diagnostics error codes.
+ */
+#define BUD_INITIAL_ERROR 0x0
+#define BUD_CHECKSUM_ERROR 0x1
+#define BUD_ADAPTER_RAM_ERROR 0x2
+#define BUD_INSTRUCTION_ERROR 0x3
+#define BUD_CONTEXT_ERROR 0x4
+#define BUD_PROTOCOL_ERROR 0x5
+#define BUD_INTERFACE_ERROR 0x6
+
+/* BUD constants */
+#define BUD_MAX_RETRIES 3
+#define BUD_MAX_LOOPCNT 6
+#define BUD_TIMEOUT 3000
+
+/* Initialization constants */
+#define INIT_MAX_RETRIES 3 /* Maximum three retries. */
+#define INIT_MAX_LOOPCNT 22 /* Maximum loop counts. */
+
+/* RING STATUS field values (high/low) */
+#define SIGNAL_LOSS 0x0080 /* Loss of signal on the ring
+ * detected.
+ */
+#define HARD_ERROR 0x0040 /* Transmitting or receiving beacon
+ * frames.
+ */
+#define SOFT_ERROR 0x0020 /* Report error MAC frame
+ * transmitted.
+ */
+#define TRANSMIT_BEACON 0x0010 /* Transmitting beacon frames on the
+ * ring.
+ */
+#define LOBE_WIRE_FAULT 0x0008 /* Open or short circuit in the
+ * cable to concentrator; adapter
+ * closed.
+ */
+#define AUTO_REMOVAL_ERROR 0x0004 /* Lobe wrap test failed, deinserted;
+ * adapter closed.
+ */
+#define REMOVE_RECEIVED 0x0001 /* Received a remove ring station MAC
+ * MAC frame request; adapter closed.
+ */
+#define COUNTER_OVERFLOW 0x8000 /* Overflow of one of the adapters
+ * error counters; READ.ERROR.LOG.
+ */
+#define SINGLE_STATION 0x4000 /* Adapter is the only station on the
+ * ring.
+ */
+#define RING_RECOVERY 0x2000 /* Claim token MAC frames on the ring;
+ * reset after ring purge frame.
+ */
+
+#define ADAPTER_CLOSED (LOBE_WIRE_FAULT | AUTO_REMOVAL_ERROR |\
+ REMOVE_RECEIVED)
+
+/* Adapter_check_block.Status field bit assignments: */
+#define DIO_PARITY 0x8000 /* Adapter detects bad parity
+ * through direct I/O access.
+ */
+#define DMA_READ_ABORT 0x4000 /* Aborting DMA read operation
+ * from system Parm[0]: 0=timeout,
+ * 1=parity error, 2=bus error;
+ * Parm[1]: 32 bit pointer to host
+ * system address at failure.
+ */
+#define DMA_WRITE_ABORT 0x2000 /* Aborting DMA write operation
+ * to system. (parameters analogous to
+ * DMA_READ_ABORT)
+ */
+#define ILLEGAL_OP_CODE 0x1000 /* Illegal operation code in the
+ * the adapters firmware Parm[0]-2:
+ * communications processor registers
+ * R13-R15.
+ */
+#define PARITY_ERRORS 0x0800 /* Adapter detects internal bus
+ * parity error.
+ */
+#define RAM_DATA_ERROR 0x0080 /* Valid only during RAM testing;
+ * RAM data error Parm[0-1]: 32 bit
+ * pointer to RAM location.
+ */
+#define RAM_PARITY_ERROR 0x0040 /* Valid only during RAM testing;
+ * RAM parity error Parm[0-1]: 32 bit
+ * pointer to RAM location.
+ */
+#define RING_UNDERRUN 0x0020 /* Internal DMA underrun when
+ * transmitting onto ring.
+ */
+#define INVALID_IRQ 0x0008 /* Unrecognized interrupt generated
+ * internal to adapter Parm[0-2]:
+ * adapter register R13-R15.
+ */
+#define INVALID_ERROR_IRQ 0x0004 /* Unrecognized error interrupt
+ * generated Parm[0-2]: adapter register
+ * R13-R15.
+ */
+#define INVALID_XOP 0x0002 /* Unrecognized XOP request in
+ * communication processor Parm[0-2]:
+ * adapter register R13-R15.
+ */
+#define CHECKADDR 0x05E0 /* Adapter check status information
+ * address offset.
+ */
+#define ROM_PAGE_0 0x0000 /* Adapter ROM page 0. */
+
+/*
+ * RECEIVE.STATUS interrupt result SSB values: (high-low)
+ * (RECEIVE_COMPLETE field bit definitions in SSB.Parm[0])
+ */
+#define RX_COMPLETE 0x0080 /* SSB.Parm[0]; SSB.Parm[1]: 32
+ * bit pointer to last RPL.
+ */
+#define RX_SUSPENDED 0x0040 /* SSB.Parm[0]; SSB.Parm[1]: 32
+ * bit pointer to RPL with odd
+ * forward pointer.
+ */
+
+/* Valid receive CSTAT: */
+#define RX_FRAME_CONTROL_BITS (RX_VALID | RX_START_FRAME | RX_END_FRAME | \
+ RX_FRAME_COMPLETE)
+#define VALID_SINGLE_BUFFER_FRAME (RX_START_FRAME | RX_END_FRAME | \
+ RX_FRAME_COMPLETE)
+
+typedef enum SKB_STAT SKB_STAT;
+enum SKB_STAT {
+ SKB_UNAVAILABLE,
+ SKB_DMA_DIRECT,
+ SKB_DATA_COPY
+};
+
+/* Receive Parameter List (RPL) The length of the RPLs has to be initialized
+ * in the OPL. (OPEN parameter list)
+ */
+#define RPL_NUM 3
+
+#define RX_FRAG_NUM 1 /* Maximal number of used fragments in one RPL.
+ * (up to firmware v2.24: 3, now: up to 9)
+ */
+
+#pragma pack(1)
+typedef struct s_RPL RPL;
+struct s_RPL { /* Receive Parameter List */
+ u_int32_t NextRPLAddr; /* Pointer to next RPL in chain
+ * (normalized = physical 32 bit
+ * address) if pointer is odd: this
+ * is last RPL. Pointing to itself can
+ * cause problems!
+ */
+ volatile u_int16_t Status; /* Set by creation of Receive Parameter
+ * List RECEIVE_CSTAT_COMPLETE set by
+ * adapter in lists that start or end
+ * a frame.
+ */
+ volatile u_int16_t FrameSize; /* Number of bytes received as a
+ * frame including AC/FC, Destination,
+ * Source, Routing field not including
+ * CRC, FS (Frame Status), End Delimiter
+ * (valid only if START_FRAME bit in
+ * CSTAT nonzero) must not be zero in
+ * any list; maximum value: (BUFFER_SIZE
+ * - 8) * TX_BUF_MAX sum of DataCount
+ * values in FragmentList must equal
+ * Frame_Size value in START_FRAME TPL!
+ * frame data fragment list
+ */
+
+ /* TPL/RPL size in OPEN parameter list depending on maximal numbers
+ * of fragments used in one parameter list.
+ */
+ Fragment FragList[RX_FRAG_NUM]; /* Maximum: nine frame fragments in
+ * one TPL. Actual version of firmware:
+ * 9 fragments possible.
+ */
+#pragma pack()
+
+ /* Special proprietary data and precalculations. */
+ RPL *NextRPLPtr; /* Logical pointer to next RPL in chain. */
+ unsigned char *MData;
+ struct sk_buff *Skb;
+ SKB_STAT SkbStat;
+ int RPLIndex;
+ dma_addr_t DMABuff; /* DMA IO bus address from pci_map */
+};
+
+/* Information that need to be kept for each board. */
+typedef struct net_local {
+#pragma pack(1)
+ IPB ipb; /* Initialization Parameter Block. */
+ SCB scb; /* System Command Block: system to adapter
+ * communication.
+ */
+ SSB ssb; /* System Status Block: adapter to system
+ * communication.
+ */
+ OPB ocpl; /* Open Options Parameter Block. */
+
+ ERRORTAB errorlogtable; /* Adapter statistic error counters.
+ * (read from adapter memory)
+ */
+ unsigned char ProductID[PROD_ID_SIZE + 1]; /* Product ID */
+#pragma pack()
+
+ TPL Tpl[TPL_NUM];
+ TPL *TplFree;
+ TPL *TplBusy;
+ unsigned char LocalTxBuffers[TPL_NUM][DEFAULT_PACKET_SIZE];
+
+ RPL Rpl[RPL_NUM];
+ RPL *RplHead;
+ RPL *RplTail;
+ unsigned char LocalRxBuffers[RPL_NUM][DEFAULT_PACKET_SIZE];
+
+ struct pci_dev *pdev;
+ int DataRate;
+ unsigned char ScbInUse;
+ unsigned short CMDqueue;
+
+ unsigned long AdapterOpenFlag:1;
+ unsigned long AdapterVirtOpenFlag:1;
+ unsigned long OpenCommandIssued:1;
+ unsigned long TransmitCommandActive:1;
+ unsigned long TransmitHaltScheduled:1;
+ unsigned long HaltInProgress:1;
+ unsigned long LobeWireFaultLogged:1;
+ unsigned long ReOpenInProgress:1;
+ unsigned long Sleeping:1;
+
+ unsigned long LastOpenStatus;
+ unsigned short CurrentRingStatus;
+ unsigned long MaxPacketSize;
+
+ unsigned long StartTime;
+ unsigned long LastSendTime;
+
+ struct tr_statistics MacStat; /* MAC statistics structure */
+
+ unsigned long dmalimit; /* the max DMA address (ie, ISA) */
+ dma_addr_t dmabuffer; /* the DMA bus address corresponding to
+ priv. Might be different from virt_to_bus()
+ for architectures with IO MMU (Alpha) */
+
+ struct timer_list timer;
+
+ wait_queue_head_t wait_for_tok_int;
+
+ INTPTRS intptrs; /* Internal adapter pointer. Must be read
+ * before OPEN command.
+ */
+ unsigned short (*setnselout)(struct net_device *);
+ unsigned short (*sifreadb)(struct net_device *, unsigned short);
+ void (*sifwriteb)(struct net_device *, unsigned short, unsigned short);
+ unsigned short (*sifreadw)(struct net_device *, unsigned short);
+ void (*sifwritew)(struct net_device *, unsigned short, unsigned short);
+
+ spinlock_t lock; /* SMP protection */
+ void *tmspriv;
+} NET_LOCAL;
+
+#endif /* __KERNEL__ */
+#endif /* __LINUX_TMS380TR_H */