diff options
Diffstat (limited to 'drivers/pci/controller/cadence/pci-j721e.c')
| -rw-r--r-- | drivers/pci/controller/cadence/pci-j721e.c | 145 |
1 files changed, 97 insertions, 48 deletions
diff --git a/drivers/pci/controller/cadence/pci-j721e.c b/drivers/pci/controller/cadence/pci-j721e.c index 284f2e0e4d26..ecd1b0312400 100644 --- a/drivers/pci/controller/cadence/pci-j721e.c +++ b/drivers/pci/controller/cadence/pci-j721e.c @@ -15,6 +15,7 @@ #include <linux/irqchip/chained_irq.h> #include <linux/irqdomain.h> #include <linux/mfd/syscon.h> +#include <linux/module.h> #include <linux/of.h> #include <linux/pci.h> #include <linux/platform_device.h> @@ -27,6 +28,7 @@ #define cdns_pcie_to_rc(p) container_of(p, struct cdns_pcie_rc, pcie) #define ENABLE_REG_SYS_2 0x108 +#define ENABLE_CLR_REG_SYS_2 0x308 #define STATUS_REG_SYS_2 0x508 #define STATUS_CLR_REG_SYS_2 0x708 #define LINK_DOWN BIT(1) @@ -116,6 +118,15 @@ static irqreturn_t j721e_pcie_link_irq_handler(int irq, void *priv) return IRQ_HANDLED; } +static void j721e_pcie_disable_link_irq(struct j721e_pcie *pcie) +{ + u32 reg; + + reg = j721e_pcie_intd_readl(pcie, ENABLE_CLR_REG_SYS_2); + reg |= pcie->linkdown_irq_regfield; + j721e_pcie_intd_writel(pcie, ENABLE_CLR_REG_SYS_2, reg); +} + static void j721e_pcie_config_link_irq(struct j721e_pcie *pcie) { u32 reg; @@ -153,11 +164,7 @@ static bool j721e_pcie_link_up(struct cdns_pcie *cdns_pcie) u32 reg; reg = j721e_pcie_user_readl(pcie, J721E_PCIE_USER_LINKSTATUS); - reg &= LINK_STATUS; - if (reg == LINK_UP_DL_COMPLETED) - return true; - - return false; + return (reg & LINK_STATUS) == LINK_UP_DL_COMPLETED; } static const struct cdns_pcie_ops j721e_pcie_ops = { @@ -277,6 +284,25 @@ static int j721e_pcie_ctrl_init(struct j721e_pcie *pcie) if (!ret) offset = args.args[0]; + /* + * The PCIe Controller's registers have different "reset-values" + * depending on the "strap" settings programmed into the PCIEn_CTRL + * register within the CTRL_MMR memory-mapped register space. + * The registers latch onto a "reset-value" based on the "strap" + * settings sampled after the PCIe Controller is powered on. + * To ensure that the "reset-values" are sampled accurately, power + * off the PCIe Controller before programming the "strap" settings + * and power it on after that. The runtime PM APIs namely + * pm_runtime_put_sync() and pm_runtime_get_sync() will decrement and + * increment the usage counter respectively, causing GENPD to power off + * and power on the PCIe Controller. + */ + ret = pm_runtime_put_sync(dev); + if (ret < 0) { + dev_err(dev, "Failed to power off PCIe Controller\n"); + return ret; + } + ret = j721e_pcie_set_mode(pcie, syscon, offset); if (ret < 0) { dev_err(dev, "Failed to set pci mode\n"); @@ -295,6 +321,12 @@ static int j721e_pcie_ctrl_init(struct j721e_pcie *pcie) return ret; } + ret = pm_runtime_get_sync(dev); + if (ret < 0) { + dev_err(dev, "Failed to power on PCIe Controller\n"); + return ret; + } + /* Enable ACSPCIE refclk output if the optional property exists */ syscon = syscon_regmap_lookup_by_phandle_optional(node, "ti,syscon-acspcie-proxy-ctrl"); @@ -355,6 +387,7 @@ static const struct j721e_pcie_data j7200_pcie_rc_data = { static const struct j721e_pcie_data j7200_pcie_ep_data = { .mode = PCI_MODE_EP, .quirk_detect_quiet_flag = true, + .linkdown_irq_regfield = J7200_LINK_DOWN, .quirk_disable_flr = true, .max_lanes = 2, }; @@ -376,16 +409,23 @@ static const struct j721e_pcie_data j784s4_pcie_rc_data = { .mode = PCI_MODE_RC, .quirk_retrain_flag = true, .byte_access_allowed = false, - .linkdown_irq_regfield = LINK_DOWN, + .linkdown_irq_regfield = J7200_LINK_DOWN, .max_lanes = 4, }; static const struct j721e_pcie_data j784s4_pcie_ep_data = { .mode = PCI_MODE_EP, - .linkdown_irq_regfield = LINK_DOWN, + .linkdown_irq_regfield = J7200_LINK_DOWN, .max_lanes = 4, }; +static const struct j721e_pcie_data j722s_pcie_rc_data = { + .mode = PCI_MODE_RC, + .linkdown_irq_regfield = J7200_LINK_DOWN, + .byte_access_allowed = true, + .max_lanes = 1, +}; + static const struct of_device_id of_j721e_pcie_match[] = { { .compatible = "ti,j721e-pcie-host", @@ -419,8 +459,13 @@ static const struct of_device_id of_j721e_pcie_match[] = { .compatible = "ti,j784s4-pcie-ep", .data = &j784s4_pcie_ep_data, }, + { + .compatible = "ti,j722s-pcie-host", + .data = &j722s_pcie_rc_data, + }, {}, }; +MODULE_DEVICE_TABLE(of, of_j721e_pcie_match); static int j721e_pcie_probe(struct platform_device *pdev) { @@ -432,9 +477,7 @@ static int j721e_pcie_probe(struct platform_device *pdev) struct j721e_pcie *pcie; struct cdns_pcie_rc *rc = NULL; struct cdns_pcie_ep *ep = NULL; - struct gpio_desc *gpiod; void __iomem *base; - struct clk *clk; u32 num_lanes; u32 mode; int ret; @@ -452,7 +495,7 @@ static int j721e_pcie_probe(struct platform_device *pdev) switch (mode) { case PCI_MODE_RC: - if (!IS_ENABLED(CONFIG_PCIE_CADENCE_HOST)) + if (!IS_ENABLED(CONFIG_PCI_J721E_HOST)) return -ENODEV; bridge = devm_pci_alloc_host_bridge(dev, sizeof(*rc)); @@ -471,7 +514,7 @@ static int j721e_pcie_probe(struct platform_device *pdev) pcie->cdns_pcie = cdns_pcie; break; case PCI_MODE_EP: - if (!IS_ENABLED(CONFIG_PCIE_CADENCE_EP)) + if (!IS_ENABLED(CONFIG_PCI_J721E_EP)) return -ENODEV; ep = devm_kzalloc(dev, sizeof(*ep), GFP_KERNEL); @@ -530,7 +573,7 @@ static int j721e_pcie_probe(struct platform_device *pdev) ret = j721e_pcie_ctrl_init(pcie); if (ret < 0) { - dev_err_probe(dev, ret, "pm_runtime_get_sync failed\n"); + dev_err_probe(dev, ret, "j721e_pcie_ctrl_init failed\n"); goto err_get_sync; } @@ -545,12 +588,12 @@ static int j721e_pcie_probe(struct platform_device *pdev) switch (mode) { case PCI_MODE_RC: - gpiod = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW); - if (IS_ERR(gpiod)) { - ret = dev_err_probe(dev, PTR_ERR(gpiod), "Failed to get reset GPIO\n"); + pcie->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW); + if (IS_ERR(pcie->reset_gpio)) { + ret = dev_err_probe(dev, PTR_ERR(pcie->reset_gpio), + "Failed to get reset GPIO\n"); goto err_get_sync; } - pcie->reset_gpio = gpiod; ret = cdns_pcie_init_phy(dev, cdns_pcie); if (ret) { @@ -558,37 +601,28 @@ static int j721e_pcie_probe(struct platform_device *pdev) goto err_get_sync; } - clk = devm_clk_get_optional(dev, "pcie_refclk"); - if (IS_ERR(clk)) { - ret = dev_err_probe(dev, PTR_ERR(clk), "failed to get pcie_refclk\n"); - goto err_pcie_setup; - } - - ret = clk_prepare_enable(clk); - if (ret) { - dev_err_probe(dev, ret, "failed to enable pcie_refclk\n"); + pcie->refclk = devm_clk_get_optional_enabled(dev, "pcie_refclk"); + if (IS_ERR(pcie->refclk)) { + ret = dev_err_probe(dev, PTR_ERR(pcie->refclk), + "failed to enable pcie_refclk\n"); goto err_pcie_setup; } - pcie->refclk = clk; /* - * The "Power Sequencing and Reset Signal Timings" table of the - * PCI Express Card Electromechanical Specification, Revision - * 5.1, Section 2.9.2, Symbol "T_PERST-CLK", indicates PERST# - * should be deasserted after minimum of 100us once REFCLK is - * stable. The REFCLK to the connector in RC mode is selected - * while enabling the PHY. So deassert PERST# after 100 us. + * Section 2.2 of the PCI Express Card Electromechanical + * Specification (Revision 5.1) mandates that the deassertion + * of the PERST# signal should be delayed by 100 ms (TPVPERL). + * This shall ensure that the power and the reference clock + * are stable. */ - if (gpiod) { - fsleep(PCIE_T_PERST_CLK_US); - gpiod_set_value_cansleep(gpiod, 1); + if (pcie->reset_gpio) { + msleep(PCIE_T_PVPERL_MS); + gpiod_set_value_cansleep(pcie->reset_gpio, 1); } ret = cdns_pcie_host_setup(rc); - if (ret < 0) { - clk_disable_unprepare(pcie->refclk); + if (ret < 0) goto err_pcie_setup; - } break; case PCI_MODE_EP: @@ -622,9 +656,21 @@ static void j721e_pcie_remove(struct platform_device *pdev) struct j721e_pcie *pcie = platform_get_drvdata(pdev); struct cdns_pcie *cdns_pcie = pcie->cdns_pcie; struct device *dev = &pdev->dev; + struct cdns_pcie_ep *ep; + struct cdns_pcie_rc *rc; + + if (pcie->mode == PCI_MODE_RC) { + rc = container_of(cdns_pcie, struct cdns_pcie_rc, pcie); + cdns_pcie_host_disable(rc); + } else { + ep = container_of(cdns_pcie, struct cdns_pcie_ep, pcie); + cdns_pcie_ep_disable(ep); + } + + gpiod_set_value_cansleep(pcie->reset_gpio, 0); - clk_disable_unprepare(pcie->refclk); cdns_pcie_disable_phy(cdns_pcie); + j721e_pcie_disable_link_irq(pcie); pm_runtime_put(dev); pm_runtime_disable(dev); } @@ -671,15 +717,14 @@ static int j721e_pcie_resume_noirq(struct device *dev) return ret; /* - * The "Power Sequencing and Reset Signal Timings" table of the - * PCI Express Card Electromechanical Specification, Revision - * 5.1, Section 2.9.2, Symbol "T_PERST-CLK", indicates PERST# - * should be deasserted after minimum of 100us once REFCLK is - * stable. The REFCLK to the connector in RC mode is selected - * while enabling the PHY. So deassert PERST# after 100 us. + * Section 2.2 of the PCI Express Card Electromechanical + * Specification (Revision 5.1) mandates that the deassertion + * of the PERST# signal should be delayed by 100 ms (TPVPERL). + * This shall ensure that the power and the reference clock + * are stable. */ if (pcie->reset_gpio) { - fsleep(PCIE_T_PERST_CLK_US); + msleep(PCIE_T_PVPERL_MS); gpiod_set_value_cansleep(pcie->reset_gpio, 1); } @@ -712,7 +757,7 @@ static DEFINE_NOIRQ_DEV_PM_OPS(j721e_pcie_pm_ops, static struct platform_driver j721e_pcie_driver = { .probe = j721e_pcie_probe, - .remove_new = j721e_pcie_remove, + .remove = j721e_pcie_remove, .driver = { .name = "j721e-pcie", .of_match_table = of_j721e_pcie_match, @@ -720,4 +765,8 @@ static struct platform_driver j721e_pcie_driver = { .pm = pm_sleep_ptr(&j721e_pcie_pm_ops), }, }; -builtin_platform_driver(j721e_pcie_driver); +module_platform_driver(j721e_pcie_driver); + +MODULE_LICENSE("GPL"); +MODULE_DESCRIPTION("PCIe controller driver for TI's J721E and related SoCs"); +MODULE_AUTHOR("Kishon Vijay Abraham I <kishon@ti.com>"); |