diff options
Diffstat (limited to 'drivers/pinctrl/Kconfig')
| -rw-r--r-- | drivers/pinctrl/Kconfig | 779 |
1 files changed, 614 insertions, 165 deletions
diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig index 5a8ad5139312..bc7f37afc48b 100644 --- a/drivers/pinctrl/Kconfig +++ b/drivers/pinctrl/Kconfig @@ -1,20 +1,25 @@ +# SPDX-License-Identifier: GPL-2.0-only # # PINCTRL infrastructure and drivers # -config PINCTRL - bool +menuconfig PINCTRL + bool "Pin controllers" if PINCTRL -menu "Pin controllers" - depends on PINCTRL +config GENERIC_PINCTRL_GROUPS + bool config PINMUX - bool "Support pin multiplexing controllers" + bool "Support pin multiplexing controllers" if COMPILE_TEST + +config GENERIC_PINMUX_FUNCTIONS + bool + select PINMUX config PINCONF - bool "Support pin configuration controllers" + bool "Support pin configuration controllers" if COMPILE_TEST config GENERIC_PINCONF bool @@ -26,107 +31,298 @@ config DEBUG_PINCTRL help Say Y here to add some extra checks and diagnostics to PINCTRL calls. -config PINCTRL_ABX500 - bool "ST-Ericsson ABx500 family Mixed Signal Circuit gpio functions" - depends on AB8500_CORE +config PINCTRL_AMD + bool "AMD GPIO pin control" + depends on HAS_IOMEM + depends on ACPI || COMPILE_TEST + select GPIOLIB + select GPIOLIB_IRQCHIP + select PINMUX + select PINCONF + select GENERIC_PINCONF + help + The driver for memory mapped GPIO functionality on AMD platforms + (x86 or arm). Most of the pins are usually muxed to some other + functionality by firmware, so only a small amount is available + for GPIO use. + + Requires ACPI/FDT device enumeration code to set up a platform + device. + +config PINCTRL_AMDISP + tristate "AMDISP GPIO pin control" + depends on DRM_AMD_ISP || COMPILE_TEST + depends on HAS_IOMEM + select GPIOLIB + select PINCONF select GENERIC_PINCONF help - Select this to enable the ABx500 family IC GPIO driver + The driver for memory mapped GPIO functionality on AMD platforms + with ISP support. All the pins are output controlled only -config PINCTRL_AB8500 - bool "AB8500 pin controller driver" - depends on PINCTRL_ABX500 && ARCH_U8500 + Requires AMDGPU to MFD add device for enumeration to set up as + platform device. -config PINCTRL_AB8540 - bool "AB8540 pin controller driver" - depends on PINCTRL_ABX500 && ARCH_U8500 +config PINCTRL_APPLE_GPIO + tristate "Apple SoC GPIO pin controller driver" + depends on ARCH_APPLE + select PINMUX + select GPIOLIB + select GPIOLIB_IRQCHIP + select GENERIC_PINCTRL_GROUPS + select GENERIC_PINMUX_FUNCTIONS + select OF_GPIO + help + This is the driver for the GPIO controller found on Apple ARM SoCs, + including M1. -config PINCTRL_AB9540 - bool "AB9540 pin controller driver" - depends on PINCTRL_ABX500 && ARCH_U8500 + This driver can also be built as a module. If so, the module + will be called pinctrl-apple-gpio. -config PINCTRL_AB8505 - bool "AB8505 pin controller driver" - depends on PINCTRL_ABX500 && ARCH_U8500 +config PINCTRL_ARTPEC6 + bool "Axis ARTPEC-6 pin controller driver" + depends on MACH_ARTPEC6 + select PINMUX + select GENERIC_PINCONF + help + This is the driver for the Axis ARTPEC-6 pin controller. This driver + supports pin function multiplexing as well as pin bias and drive + strength configuration. Device tree integration instructions can be + found in Documentation/devicetree/bindings/pinctrl/axis,artpec6-pinctrl.txt + +config PINCTRL_AS3722 + tristate "Pinctrl and GPIO driver for ams AS3722 PMIC" + depends on MFD_AS3722 && GPIOLIB + select PINMUX + select GENERIC_PINCONF + help + AS3722 device supports the configuration of GPIO pins for different + functionality. This driver supports the pinmux, push-pull and + open drain configuration for the GPIO pins of AS3722 devices. It also + supports the GPIO functionality through gpiolib. config PINCTRL_AT91 bool "AT91 pinctrl driver" - depends on OF - depends on ARCH_AT91 + depends on (OF && ARCH_AT91) || COMPILE_TEST select PINMUX select PINCONF + select GPIOLIB + select GPIOLIB_IRQCHIP help Say Y here to enable the at91 pinctrl driver -config PINCTRL_BAYTRAIL - bool "Intel Baytrail GPIO pin control" - depends on GPIOLIB && ACPI && X86 - select IRQ_DOMAIN +config PINCTRL_AT91PIO4 + bool "AT91 PIO4 pinctrl driver" + depends on OF + depends on HAS_IOMEM + depends on ARCH_AT91 || COMPILE_TEST + select PINMUX + select GENERIC_PINCONF + select GPIOLIB + select GPIOLIB_IRQCHIP + select OF_GPIO help - driver for memory mapped GPIO functionality on Intel Baytrail - platforms. Supports 3 banks with 102, 28 and 44 gpios. - Most pins are usually muxed to some other functionality by firmware, - so only a small amount is available for gpio use. - - Requires ACPI device enumeration code to set up a platform device. + Say Y here to enable the at91 pinctrl/gpio driver for Atmel PIO4 + controller available on sama5d2 SoC. -config PINCTRL_BCM2835 - bool +config PINCTRL_AXP209 + tristate "X-Powers AXP209 PMIC pinctrl and GPIO Support" + depends on MFD_AXP20X + depends on OF + select PINMUX + select GENERIC_PINCONF + select GPIOLIB + help + AXP PMICs provides multiple GPIOs that can be muxed for different + functions. This driver bundles a pinctrl driver to select the function + muxing and a GPIO driver to handle the GPIO when the GPIO function is + selected. + Say Y to enable pinctrl and GPIO support for the AXP209 PMIC. + +config PINCTRL_AW9523 + tristate "Awinic AW9523/AW9523B I2C GPIO expander pinctrl driver" + depends on OF && I2C select PINMUX select PINCONF + select GENERIC_PINCONF + select GPIOLIB + select GPIOLIB_IRQCHIP + select REGMAP + select REGMAP_I2C + help + The Awinic AW9523/AW9523B is a multi-function I2C GPIO + expander with PWM functionality. This driver bundles a + pinctrl driver to select the function muxing and a GPIO + driver to handle GPIO, when the GPIO function is selected. -config PINCTRL_IMX - bool + Say yes to enable pinctrl and GPIO support for the AW9523(B). + +config PINCTRL_BM1880 + bool "Bitmain BM1880 Pinctrl driver" + depends on OF && (ARCH_BITMAIN || COMPILE_TEST) + default ARCH_BITMAIN + select PINMUX + help + Pinctrl driver for Bitmain BM1880 SoC. + +config PINCTRL_CY8C95X0 + tristate "Cypress CY8C95X0 I2C pinctrl and GPIO driver" + depends on I2C + select GPIOLIB + select GPIOLIB_IRQCHIP select PINMUX select PINCONF + select GENERIC_PINCONF + select REGMAP_I2C + help + Support for 20/40/60 pin Cypress Cy8C95x0 pinctrl/gpio I2C expander. + This driver can also be built as a module. If so, the module will be + called pinctrl-cy8c95x0. -config PINCTRL_IMX35 - bool "IMX35 pinctrl driver" - depends on OF - depends on SOC_IMX35 - select PINCTRL_IMX +config PINCTRL_DA850_PUPD + tristate "TI DA850/OMAP-L138/AM18XX pull-up and pull-down groups" + depends on OF && (ARCH_DAVINCI_DA850 || COMPILE_TEST) + select PINCONF + select GENERIC_PINCONF help - Say Y here to enable the imx35 pinctrl driver + Driver for TI DA850/OMAP-L138/AM18XX pinconf. Used to control + pull-up and pull-down pin groups. -config PINCTRL_IMX51 - bool "IMX51 pinctrl driver" - depends on OF - depends on SOC_IMX51 - select PINCTRL_IMX +config PINCTRL_DA9062 + tristate "Dialog Semiconductor DA9062 PMIC pinctrl and GPIO Support" + depends on MFD_DA9062 + select GPIOLIB help - Say Y here to enable the imx51 pinctrl driver + The Dialog DA9062 PMIC provides multiple GPIOs that can be muxed for + different functions. This driver bundles a pinctrl driver to select the + function muxing and a GPIO driver to handle the GPIO when the GPIO + function is selected. -config PINCTRL_IMX53 - bool "IMX53 pinctrl driver" - depends on OF - depends on SOC_IMX53 - select PINCTRL_IMX + Say Y to enable pinctrl and GPIO support for the DA9062 PMIC. + +config PINCTRL_DIGICOLOR + bool + depends on ARCH_DIGICOLOR || COMPILE_TEST + select PINMUX + select GENERIC_PINCONF + +config PINCTRL_EIC7700 + tristate "EIC7700 PINCTRL driver" + depends on ARCH_ESWIN || COMPILE_TEST + select PINMUX + select GENERIC_PINCONF + select REGULATOR + select REGULATOR_FIXED_VOLTAGE help - Say Y here to enable the imx53 pinctrl driver + This driver support for the pin controller in ESWIN's EIC7700 SoC, + which supports pin multiplexing, pin configuration,and rgmii voltage + control. + Say Y here to enable the eic7700 pinctrl driver + +config PINCTRL_EP93XX + bool + depends on ARCH_EP93XX || COMPILE_TEST + select PINMUX + select GENERIC_PINCONF + select MFD_SYSCON -config PINCTRL_IMX6Q - bool "IMX6Q/DL pinctrl driver" +config PINCTRL_EQUILIBRIUM + tristate "Generic pinctrl and GPIO driver for Intel Lightning Mountain SoC" + depends on OF && HAS_IOMEM + depends on X86 || COMPILE_TEST + select PINMUX + select PINCONF + select GPIOLIB + select GPIO_GENERIC + select GPIOLIB_IRQCHIP + select GENERIC_PINCONF + select GENERIC_PINCTRL_GROUPS + select GENERIC_PINMUX_FUNCTIONS + help + Equilibrium driver is a pinctrl and GPIO driver for Intel Lightning + Mountain network processor SoC that supports both the GPIO and pin + control frameworks. It provides interfaces to setup pin muxing, assign + desired pin functions, configure GPIO attributes for LGM SoC pins. + Pin muxing and pin config settings are retrieved from device tree. + +config PINCTRL_EYEQ5 + bool "Mobileye EyeQ5 pinctrl driver" depends on OF - depends on SOC_IMX6Q - select PINCTRL_IMX + depends on MACH_EYEQ5 || COMPILE_TEST + select PINMUX + select GENERIC_PINCONF + select AUXILIARY_BUS + default MACH_EYEQ5 help - Say Y here to enable the imx6q/dl pinctrl driver + Pin controller driver for the Mobileye EyeQ5 platform. It does both + pin config & pin muxing. It does not handle GPIO. + + Pin muxing supports two functions for each pin: first is GPIO, second + is pin-dependent. Pin config is about bias & drive strength. + +config PINCTRL_GEMINI + bool + depends on ARCH_GEMINI + default ARCH_GEMINI + select PINMUX + select GENERIC_PINCONF + select MFD_SYSCON -config PINCTRL_IMX6SL - bool "IMX6SL pinctrl driver" +config PINCTRL_INGENIC + bool "Pinctrl driver for the Ingenic JZ47xx SoCs" + default MACH_INGENIC depends on OF - depends on SOC_IMX6SL - select PINCTRL_IMX + depends on MIPS || COMPILE_TEST + select GENERIC_PINCONF + select GENERIC_PINCTRL_GROUPS + select GENERIC_PINMUX_FUNCTIONS + select GPIOLIB + select GPIOLIB_IRQCHIP + select REGMAP_MMIO + +config PINCTRL_K210 + bool "Pinctrl driver for the Canaan Kendryte K210 SoC" + depends on RISCV && SOC_CANAAN_K210 || COMPILE_TEST + depends on OF + select GENERIC_PINMUX_FUNCTIONS + select GENERIC_PINCONF + select GPIOLIB + select OF_GPIO + select REGMAP_MMIO + default SOC_CANAAN_K210 help - Say Y here to enable the imx6sl pinctrl driver + Add support for the Canaan Kendryte K210 RISC-V SOC Field + Programmable IO Array (FPIOA) controller. -config PINCTRL_VF610 - bool "Freescale Vybrid VF610 pinctrl driver" +config PINCTRL_K230 + bool "Pinctrl driver for the Canaan Kendryte K230 SoC" depends on OF - depends on SOC_VF610 - select PINCTRL_IMX + depends on ARCH_CANAAN || COMPILE_TEST + select GENERIC_PINCTRL_GROUPS + select GENERIC_PINMUX_FUNCTIONS + select GENERIC_PINCONF + select REGMAP_MMIO help - Say Y here to enable the Freescale Vybrid VF610 pinctrl driver + Add support for the Canaan Kendryte K230 RISC-V SOC pin controller. + +config PINCTRL_KEEMBAY + tristate "Pinctrl driver for Intel Keem Bay SoC" + depends on ARCH_KEEMBAY || (ARM64 && COMPILE_TEST) + depends on HAS_IOMEM + select PINMUX + select PINCONF + select GENERIC_PINCONF + select GENERIC_PINCTRL_GROUPS + select GENERIC_PINMUX_FUNCTIONS + select GPIOLIB + select GPIOLIB_IRQCHIP + select GPIO_GENERIC + help + This selects pin control driver for the Intel Keem Bay SoC. + It provides pin config functions such as pull-up, pull-down, + interrupt, drive strength, sec lock, Schmitt trigger, slew + rate control and direction control. This module will be + called as pinctrl-keembay. config PINCTRL_LANTIQ bool @@ -139,148 +335,401 @@ config PINCTRL_FALCON depends on SOC_FALCON depends on PINCTRL_LANTIQ -config PINCTRL_MXS - bool +config PINCTRL_LOONGSON2 + tristate "Pinctrl driver for the Loongson-2 SoC" + depends on OF && (LOONGARCH || COMPILE_TEST) select PINMUX - select PINCONF + select GENERIC_PINCONF + help + This selects pin control driver for the Loongson-2 SoC. It + provides pin config functions multiplexing. GPIO pin pull-up, + pull-down functions are not supported. Say yes to enable + pinctrl for Loongson-2 SoC. -config PINCTRL_IMX23 +config PINCTRL_XWAY bool - select PINCTRL_MXS + depends on SOC_TYPE_XWAY + depends on PINCTRL_LANTIQ -config PINCTRL_IMX28 - bool - select PINCTRL_MXS +config PINCTRL_LPC18XX + bool "NXP LPC18XX/43XX SCU pinctrl driver" + depends on OF && (ARCH_LPC18XX || COMPILE_TEST) + default ARCH_LPC18XX + select PINMUX + select GENERIC_PINCONF + help + Pinctrl driver for NXP LPC18xx/43xx System Control Unit (SCU). -config PINCTRL_NOMADIK - bool "Nomadik pin controller driver" - depends on ARCH_U8500 || ARCH_NOMADIK +config PINCTRL_MAX7360 + tristate "MAX7360 Pincontrol support" + depends on MFD_MAX7360 + select PINMUX + select GENERIC_PINCONF + help + Say Y here to enable pin control support for Maxim MAX7360 keypad + controller. + This keypad controller has 8 GPIO pins that may work as GPIO, or PWM, + or rotary encoder alternate modes. + +config PINCTRL_MAX77620 + tristate "MAX77620/MAX20024 Pincontrol support" + depends on MFD_MAX77620 && OF + select PINMUX + select GENERIC_PINCONF + help + Say Y here to enable Pin control support for Maxim MAX77620 PMIC. + This PMIC has 8 GPIO pins that work as GPIO as well as special + function in alternate mode. This driver also configure push-pull, + open drain, FPS slots etc. + +config PINCTRL_MCP23S08_I2C + tristate + select REGMAP_I2C + +config PINCTRL_MCP23S08_SPI + tristate + select REGMAP_SPI + +config PINCTRL_MCP23S08 + tristate "Microchip MCP23xxx I/O expander" + depends on SPI_MASTER || I2C + select GPIOLIB + select GPIOLIB_IRQCHIP + select GENERIC_PINCONF + select PINCTRL_MCP23S08_I2C if I2C + select PINCTRL_MCP23S08_SPI if SPI_MASTER + help + SPI/I2C driver for Microchip MCP23S08 / MCP23S17 / MCP23S18 / + MCP23008 / MCP23017 / MCP23018 I/O expanders. + This provides a GPIO interface supporting inputs and outputs and a + corresponding interrupt-controller. + +config PINCTRL_MICROCHIP_SGPIO + tristate "Pinctrl driver for Microsemi/Microchip Serial GPIO" + depends on OF + depends on HAS_IOMEM + select GPIOLIB + select GPIOLIB_IRQCHIP + select GENERIC_PINCONF + select GENERIC_PINCTRL_GROUPS + select GENERIC_PINMUX_FUNCTIONS + select OF_GPIO + help + Support for the serial GPIO interface used on Microsemi and + Microchip SoCs. By using a serial interface, the SIO + controller significantly extends the number of available + GPIOs with a minimum number of additional pins on the + device. The primary purpose of the SIO controller is to + connect control signals from SFP modules and to act as an + LED controller. + + If compiled as a module, the module name will be + pinctrl-microchip-sgpio. + +config PINCTRL_OCELOT + tristate "Pinctrl driver for the Microsemi Ocelot and Jaguar2 SoCs" + depends on OF + depends on HAS_IOMEM + select GPIOLIB + select GPIOLIB_IRQCHIP + select GENERIC_PINCONF + select GENERIC_PINCTRL_GROUPS + select GENERIC_PINMUX_FUNCTIONS + select OF_GPIO + select REGMAP_MMIO + help + Support for the internal GPIO interfaces on Microsemi Ocelot and + Jaguar2 SoCs. + + If conpiled as a module, the module name will be pinctrl-ocelot. + +config PINCTRL_PALMAS + tristate "Pinctrl driver for the PALMAS Series MFD devices" + depends on OF && MFD_PALMAS + select PINMUX + select GENERIC_PINCONF + help + Palmas device supports the configuration of pins for different + functionality. This driver supports the pinmux, push-pull and + open drain configuration for the Palmas series devices like + TPS65913, TPS80036 etc. + +config PINCTRL_PEF2256 + tristate "Lantiq PEF2256 (FALC56) pin controller driver" + depends on OF && FRAMER_PEF2256 select PINMUX select PINCONF + select GENERIC_PINCONF + help + This option enables the pin controller support for the Lantiq PEF2256 + framer, also known as FALC56. -config PINCTRL_STN8815 - bool "STN8815 pin controller driver" - depends on PINCTRL_NOMADIK && ARCH_NOMADIK + If unsure, say N. -config PINCTRL_DB8500 - bool "DB8500 pin controller driver" - depends on PINCTRL_NOMADIK && ARCH_U8500 + To compile this driver as a module, choose M here: the + module will be called pinctrl-pef2256. -config PINCTRL_DB8540 - bool "DB8540 pin controller driver" - depends on PINCTRL_NOMADIK && ARCH_U8500 +config PINCTRL_PIC32 + bool "Microchip PIC32 pin controller driver" + depends on OF + depends on MACH_PIC32 + select PINMUX + select GENERIC_PINCONF + select GPIOLIB_IRQCHIP + select OF_GPIO + help + This is the pin controller and gpio driver for Microchip PIC32 + microcontrollers. This option is selected automatically when specific + machine and arch are selected to build. -config PINCTRL_ROCKCHIP - bool +config PINCTRL_PIC32MZDA + def_bool y if PIC32MZDA + select PINCTRL_PIC32 + +config PINCTRL_PIC64GX + bool "pic64gx gpio2 pinctrl driver" + depends on ARCH_MICROCHIP || COMPILE_TEST + depends on OF + select GENERIC_PINCONF + default y + help + This selects the pinctrl driver for gpio2 on pic64gx. + +config PINCTRL_PISTACHIO + bool "IMG Pistachio SoC pinctrl driver" + depends on OF && (MIPS || COMPILE_TEST) + depends on GPIOLIB select PINMUX select GENERIC_PINCONF - select GENERIC_IRQ_CHIP + select GPIOLIB_IRQCHIP + select OF_GPIO + help + This support pinctrl and GPIO driver for IMG Pistachio SoC. -config PINCTRL_SINGLE - tristate "One-register-per-pin type device tree based pinctrl driver" +config PINCTRL_POLARFIRE_SOC + bool "Polarfire SoC pinctrl driver" + depends on ARCH_MICROCHIP || COMPILE_TEST depends on OF + select GENERIC_PINCONF + default y + help + This selects the pinctrl driver for Microchip Polarfire SoC. + +config PINCTRL_RK805 + tristate "Pinctrl and GPIO driver for RK805 PMIC" + depends on MFD_RK8XX + select GPIOLIB select PINMUX - select PINCONF select GENERIC_PINCONF help - This selects the device tree based generic pinctrl driver. + This selects the pinctrl driver for RK805. -config PINCTRL_SIRF - bool "CSR SiRFprimaII/SiRFmarco pin controller driver" - depends on ARCH_SIRF +config PINCTRL_ROCKCHIP + tristate "Rockchip gpio and pinctrl driver" + depends on ARCH_ROCKCHIP || COMPILE_TEST + depends on OF + select GPIOLIB select PINMUX + select GENERIC_PINCONF + select GENERIC_IRQ_CHIP + select MFD_SYSCON + select OF_GPIO + default ARCH_ROCKCHIP + help + This support pinctrl and GPIO driver for Rockchip SoCs. -config PINCTRL_SUNXI - bool +config PINCTRL_SCMI + tristate "Pinctrl driver using SCMI protocol interface" + depends on ARM_SCMI_PROTOCOL || COMPILE_TEST select PINMUX select GENERIC_PINCONF + help + This driver provides support for pinctrl which is controlled + by firmware that implements the SCMI interface. + It uses SCMI Message Protocol to interact with the + firmware providing all the pinctrl controls. + +config PINCTRL_SINGLE + tristate "One-register-per-pin type device tree based pinctrl driver" + depends on OF + depends on HAS_IOMEM + select GENERIC_PINCTRL_GROUPS + select GENERIC_PINMUX_FUNCTIONS + select GENERIC_PINCONF + help + This selects the device tree based generic pinctrl driver. config PINCTRL_ST bool depends on OF select PINMUX select PINCONF + select GPIOLIB_IRQCHIP -config PINCTRL_TEGRA - bool +config PINCTRL_STMFX + tristate "STMicroelectronics STMFX GPIO expander pinctrl driver" + depends on I2C + depends on OF_GPIO + depends on HAS_IOMEM + select GENERIC_PINCONF + select GPIOLIB_IRQCHIP + select MFD_STMFX + help + Driver for STMicroelectronics Multi-Function eXpander (STMFX) + GPIO expander. + This provides a GPIO interface supporting inputs and outputs, + and configuring push-pull, open-drain, and can also be used as + interrupt-controller. + +config PINCTRL_SX150X + tristate "Semtech SX150x I2C GPIO expander pinctrl driver" + depends on I2C=y select PINMUX select PINCONF + select GENERIC_PINCONF + select GPIOLIB + select GPIOLIB_IRQCHIP + select REGMAP + help + Say Y here to provide support for Semtech SX150x-series I2C + GPIO expanders as pinctrl module. + Compatible models include: + - 8 bits: sx1508q, sx1502q + - 16 bits: sx1509q, sx1506q + +config PINCTRL_TB10X + bool "Pinctrl for TB10X" if COMPILE_TEST + depends on OF && ARC_PLAT_TB10X || COMPILE_TEST + select GPIOLIB + +config PINCTRL_TPS6594 + tristate "Pinctrl and GPIO driver for TI TPS6594 PMIC" + depends on OF && MFD_TPS6594 + default MFD_TPS6594 + select PINMUX + select GPIOLIB + select REGMAP + select GPIO_REGMAP + select GENERIC_PINCONF + help + Say Y to select the pinmuxing and GPIOs driver for the TPS6594 + PMICs chip family. -config PINCTRL_TEGRA20 - bool - select PINCTRL_TEGRA + This driver can also be built as a module + called tps6594-pinctrl. -config PINCTRL_TEGRA30 - bool - select PINCTRL_TEGRA +config PINCTRL_TH1520 + tristate "Pinctrl driver for the T-Head TH1520 SoC" + depends on ARCH_THEAD || COMPILE_TEST + depends on OF + select GENERIC_PINMUX_FUNCTIONS + select GENERIC_PINCONF + select PINMUX + help + This is the driver for the pin controller blocks on the + T-Head TH1520 SoC. -config PINCTRL_TEGRA114 - bool - select PINCTRL_TEGRA + This driver is needed for RISC-V development boards like + the BeagleV Ahead and the LicheePi 4A. -config PINCTRL_TZ1090 - bool "Toumaz Xenif TZ1090 pin control driver" - depends on SOC_TZ1090 +config PINCTRL_UPBOARD + tristate "AAeon UP board FPGA pin controller" + depends on MFD_UPBOARD_FPGA select PINMUX - select GENERIC_PINCONF + select GENERIC_PINCTRL_GROUPS + select GENERIC_PINMUX_FUNCTIONS + select GPIOLIB + select GPIO_AGGREGATOR + help + Pin controller for the FPGA GPIO lines on UP boards. Due to the + hardware layout, the driver controls the FPGA pins in tandem with + their corresponding Intel SoC GPIOs. -config PINCTRL_TZ1090_PDC - bool "Toumaz Xenif TZ1090 PDC pin control driver" - depends on SOC_TZ1090 - select PINMUX - select PINCONF + Currently supported: + - UP Squared -config PINCTRL_U300 - bool "U300 pin controller driver" - depends on ARCH_U300 + To compile this driver as a module, choose M here: the module + will be called pinctrl-upboard. + +config PINCTRL_ZYNQ + bool "Pinctrl driver for Xilinx Zynq" + depends on ARCH_ZYNQ || COMPILE_TEST + depends on OF select PINMUX select GENERIC_PINCONF - -config PINCTRL_COH901 - bool "ST-Ericsson U300 COH 901 335/571 GPIO" - depends on GPIOLIB && ARCH_U300 && PINCTRL_U300 help - Say yes here to support GPIO interface on ST-Ericsson U300. - The names of the two IP block variants supported are - COH 901 335 and COH 901 571/3. They contain 3, 5 or 7 - ports of 8 GPIO pins each. + This selects the pinctrl driver for Xilinx Zynq. -config PINCTRL_SAMSUNG - bool +config PINCTRL_ZYNQMP + tristate "Pinctrl driver for Xilinx ZynqMP" + depends on ZYNQMP_FIRMWARE select PINMUX - select PINCONF - -config PINCTRL_EXYNOS - bool "Pinctrl driver data for Samsung EXYNOS SoCs other than 5440" - depends on OF && GPIOLIB && ARCH_EXYNOS - select PINCTRL_SAMSUNG - -config PINCTRL_EXYNOS5440 - bool "Samsung EXYNOS5440 SoC pinctrl driver" - depends on SOC_EXYNOS5440 + select GENERIC_PINCONF + default ZYNQMP_FIRMWARE + help + This selects the pinctrl driver for Xilinx ZynqMP platform. + This driver will query the pin information from the firmware + and allow configuring the pins. + Configuration can include the mux function to select on those + pin(s)/group(s), and various pin configuration parameters + such as pull-up, slew rate, etc. + This driver can also be built as a module. If so, the module + will be called pinctrl-zynqmp. + +config PINCTRL_MLXBF3 + tristate "NVIDIA BlueField-3 SoC Pinctrl driver" + depends on (MELLANOX_PLATFORM && ARM64) || COMPILE_TEST + select PINMUX + select GPIOLIB + select GPIOLIB_IRQCHIP + help + Say Y to select the pinctrl driver for BlueField-3 SoCs. + This pin controller allows selecting the mux function for + each pin. This driver can also be built as a module called + pinctrl-mlxbf3. + +config PINCTRL_RP1 + tristate "Pinctrl driver for RP1" + depends on MISC_RP1 + default MISC_RP1 select PINMUX select PINCONF - -config PINCTRL_S3C24XX - bool "Samsung S3C24XX SoC pinctrl driver" - depends on ARCH_S3C24XX - select PINCTRL_SAMSUNG - -config PINCTRL_S3C64XX - bool "Samsung S3C64XX SoC pinctrl driver" - depends on ARCH_S3C64XX - select PINCTRL_SAMSUNG - + select GENERIC_PINCONF + help + Enable the gpio and pinctrl/mux driver for RaspberryPi RP1 + multi function device. + +source "drivers/pinctrl/actions/Kconfig" +source "drivers/pinctrl/aspeed/Kconfig" +source "drivers/pinctrl/bcm/Kconfig" +source "drivers/pinctrl/berlin/Kconfig" +source "drivers/pinctrl/cirrus/Kconfig" +source "drivers/pinctrl/cix/Kconfig" +source "drivers/pinctrl/freescale/Kconfig" +source "drivers/pinctrl/intel/Kconfig" +source "drivers/pinctrl/mediatek/Kconfig" +source "drivers/pinctrl/meson/Kconfig" source "drivers/pinctrl/mvebu/Kconfig" -source "drivers/pinctrl/sh-pfc/Kconfig" +source "drivers/pinctrl/nomadik/Kconfig" +source "drivers/pinctrl/nuvoton/Kconfig" +source "drivers/pinctrl/nxp/Kconfig" +source "drivers/pinctrl/pxa/Kconfig" +source "drivers/pinctrl/qcom/Kconfig" +source "drivers/pinctrl/realtek/Kconfig" +source "drivers/pinctrl/renesas/Kconfig" +source "drivers/pinctrl/samsung/Kconfig" +source "drivers/pinctrl/sophgo/Kconfig" +source "drivers/pinctrl/spacemit/Kconfig" source "drivers/pinctrl/spear/Kconfig" +source "drivers/pinctrl/sprd/Kconfig" +source "drivers/pinctrl/starfive/Kconfig" +source "drivers/pinctrl/stm32/Kconfig" +source "drivers/pinctrl/sunplus/Kconfig" +source "drivers/pinctrl/sunxi/Kconfig" +source "drivers/pinctrl/tegra/Kconfig" +source "drivers/pinctrl/ti/Kconfig" +source "drivers/pinctrl/uniphier/Kconfig" +source "drivers/pinctrl/visconti/Kconfig" source "drivers/pinctrl/vt8500/Kconfig" -config PINCTRL_XWAY - bool - depends on SOC_TYPE_XWAY - depends on PINCTRL_LANTIQ - -endmenu - endif |