diff options
Diffstat (limited to 'drivers/usb/host/xhci-rcar.c')
| -rw-r--r-- | drivers/usb/host/xhci-rcar.c | 303 |
1 files changed, 171 insertions, 132 deletions
diff --git a/drivers/usb/host/xhci-rcar.c b/drivers/usb/host/xhci-rcar.c index a6e463715779..8a993ee21c87 100644 --- a/drivers/usb/host/xhci-rcar.c +++ b/drivers/usb/host/xhci-rcar.c @@ -6,84 +6,32 @@ */ #include <linux/firmware.h> +#include <linux/iopoll.h> #include <linux/module.h> #include <linux/platform_device.h> #include <linux/of.h> #include <linux/usb/phy.h> -#include <linux/sys_soc.h> +#include <linux/reset.h> #include "xhci.h" #include "xhci-plat.h" -#include "xhci-rcar.h" +#include "xhci-rcar-regs.h" +#include "xhci-rzg3e-regs.h" +#include "xhci-rzv2m.h" + +#define XHCI_RCAR_FIRMWARE_NAME_V1 "r8a779x_usb3_v1.dlmem" +#define XHCI_RCAR_FIRMWARE_NAME_V3 "r8a779x_usb3_v3.dlmem" /* -* - The V3 firmware is for almost all R-Car Gen3 (except r8a7795 ES1.x) -* - The V2 firmware is for r8a7795 ES1.x. +* - The V3 firmware is for all R-Car Gen3 * - The V2 firmware is possible to use on R-Car Gen2. However, the V2 causes * performance degradation. So, this driver continues to use the V1 if R-Car * Gen2. * - The V1 firmware is impossible to use on R-Car Gen3. */ MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V1); -MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V2); MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V3); -/*** Register Offset ***/ -#define RCAR_USB3_AXH_STA 0x104 /* AXI Host Control Status */ -#define RCAR_USB3_INT_ENA 0x224 /* Interrupt Enable */ -#define RCAR_USB3_DL_CTRL 0x250 /* FW Download Control & Status */ -#define RCAR_USB3_FW_DATA0 0x258 /* FW Data0 */ - -#define RCAR_USB3_LCLK 0xa44 /* LCLK Select */ -#define RCAR_USB3_CONF1 0xa48 /* USB3.0 Configuration1 */ -#define RCAR_USB3_CONF2 0xa5c /* USB3.0 Configuration2 */ -#define RCAR_USB3_CONF3 0xaa8 /* USB3.0 Configuration3 */ -#define RCAR_USB3_RX_POL 0xab0 /* USB3.0 RX Polarity */ -#define RCAR_USB3_TX_POL 0xab8 /* USB3.0 TX Polarity */ - -/*** Register Settings ***/ -/* AXI Host Control Status */ -#define RCAR_USB3_AXH_STA_B3_PLL_ACTIVE 0x00010000 -#define RCAR_USB3_AXH_STA_B2_PLL_ACTIVE 0x00000001 -#define RCAR_USB3_AXH_STA_PLL_ACTIVE_MASK (RCAR_USB3_AXH_STA_B3_PLL_ACTIVE | \ - RCAR_USB3_AXH_STA_B2_PLL_ACTIVE) - -/* Interrupt Enable */ -#define RCAR_USB3_INT_XHC_ENA 0x00000001 -#define RCAR_USB3_INT_PME_ENA 0x00000002 -#define RCAR_USB3_INT_HSE_ENA 0x00000004 -#define RCAR_USB3_INT_ENA_VAL (RCAR_USB3_INT_XHC_ENA | \ - RCAR_USB3_INT_PME_ENA | RCAR_USB3_INT_HSE_ENA) - -/* FW Download Control & Status */ -#define RCAR_USB3_DL_CTRL_ENABLE 0x00000001 -#define RCAR_USB3_DL_CTRL_FW_SUCCESS 0x00000010 -#define RCAR_USB3_DL_CTRL_FW_SET_DATA0 0x00000100 - -/* LCLK Select */ -#define RCAR_USB3_LCLK_ENA_VAL 0x01030001 - -/* USB3.0 Configuration */ -#define RCAR_USB3_CONF1_VAL 0x00030204 -#define RCAR_USB3_CONF2_VAL 0x00030300 -#define RCAR_USB3_CONF3_VAL 0x13802007 - -/* USB3.0 Polarity */ -#define RCAR_USB3_RX_POL_VAL BIT(21) -#define RCAR_USB3_TX_POL_VAL BIT(4) - -/* For soc_device_attribute */ -#define RCAR_XHCI_FIRMWARE_V2 BIT(0) /* FIRMWARE V2 */ -#define RCAR_XHCI_FIRMWARE_V3 BIT(1) /* FIRMWARE V3 */ - -static const struct soc_device_attribute rcar_quirks_match[] = { - { - .soc_id = "r8a7795", .revision = "ES1.*", - .data = (void *)RCAR_XHCI_FIRMWARE_V2, - }, - { /* sentinel */ }, -}; - static void xhci_rcar_start_gen2(struct usb_hcd *hcd) { /* LCLK Select */ @@ -104,19 +52,10 @@ static int xhci_rcar_is_gen2(struct device *dev) return of_device_is_compatible(node, "renesas,xhci-r8a7790") || of_device_is_compatible(node, "renesas,xhci-r8a7791") || of_device_is_compatible(node, "renesas,xhci-r8a7793") || - of_device_is_compatible(node, "renensas,rcar-gen2-xhci"); -} - -static int xhci_rcar_is_gen3(struct device *dev) -{ - struct device_node *node = dev->of_node; - - return of_device_is_compatible(node, "renesas,xhci-r8a7795") || - of_device_is_compatible(node, "renesas,xhci-r8a7796") || - of_device_is_compatible(node, "renesas,rcar-gen3-xhci"); + of_device_is_compatible(node, "renesas,rcar-gen2-xhci"); } -void xhci_rcar_start(struct usb_hcd *hcd) +static void xhci_rcar_start(struct usb_hcd *hcd) { u32 temp; @@ -130,32 +69,66 @@ void xhci_rcar_start(struct usb_hcd *hcd) } } +static void xhci_rzg3e_start(struct usb_hcd *hcd) +{ + u32 int_en; + + if (hcd->regs) { + /* Update the controller initial setting */ + writel(0x03130200, hcd->regs + RZG3E_USB3_HOST_U3P0PIPESC(0)); + writel(0x00160200, hcd->regs + RZG3E_USB3_HOST_U3P0PIPESC(1)); + writel(0x03150000, hcd->regs + RZG3E_USB3_HOST_U3P0PIPESC(2)); + writel(0x03130200, hcd->regs + RZG3E_USB3_HOST_U3P0PIPESC(3)); + writel(0x00180000, hcd->regs + RZG3E_USB3_HOST_U3P0PIPESC(4)); + + /* Interrupt Enable */ + int_en = readl(hcd->regs + RZG3E_USB3_HOST_INTEN); + int_en |= RZG3E_USB3_HOST_INTEN_ENA; + writel(int_en, hcd->regs + RZG3E_USB3_HOST_INTEN); + } +} + +static int xhci_rzg3e_resume(struct usb_hcd *hcd) +{ + struct xhci_hcd *xhci = hcd_to_xhci(hcd); + + return reset_control_deassert(xhci->reset); +} + +static int xhci_rzg3e_post_resume(struct usb_hcd *hcd) +{ + xhci_rzg3e_start(hcd); + + return 0; +} + +static int xhci_rzg3e_suspend(struct usb_hcd *hcd) +{ + struct xhci_hcd *xhci = hcd_to_xhci(hcd); + + reset_control_assert(xhci->reset); + + return 0; +} + static int xhci_rcar_download_firmware(struct usb_hcd *hcd) { struct device *dev = hcd->self.controller; void __iomem *regs = hcd->regs; struct xhci_plat_priv *priv = hcd_to_xhci_priv(hcd); const struct firmware *fw; - int retval, index, j, time; - int timeout = 10000; + int retval, index, j; u32 data, val, temp; - u32 quirks = 0; - const struct soc_device_attribute *attr; - const char *firmware_name; - attr = soc_device_match(rcar_quirks_match); - if (attr) - quirks = (uintptr_t)attr->data; - - if (quirks & RCAR_XHCI_FIRMWARE_V2) - firmware_name = XHCI_RCAR_FIRMWARE_NAME_V2; - else if (quirks & RCAR_XHCI_FIRMWARE_V3) - firmware_name = XHCI_RCAR_FIRMWARE_NAME_V3; - else - firmware_name = priv->firmware_name; + /* + * According to the datasheet, "Upon the completion of FW Download, + * there is no need to write or reload FW". + */ + if (readl(regs + RCAR_USB3_DL_CTRL) & RCAR_USB3_DL_CTRL_FW_SUCCESS) + return 0; /* request R-Car USB3.0 firmware */ - retval = request_firmware(&fw, firmware_name, dev); + retval = request_firmware(&fw, priv->firmware_name, dev); if (retval) return retval; @@ -175,32 +148,19 @@ static int xhci_rcar_download_firmware(struct usb_hcd *hcd) temp |= RCAR_USB3_DL_CTRL_FW_SET_DATA0; writel(temp, regs + RCAR_USB3_DL_CTRL); - for (time = 0; time < timeout; time++) { - val = readl(regs + RCAR_USB3_DL_CTRL); - if ((val & RCAR_USB3_DL_CTRL_FW_SET_DATA0) == 0) - break; - udelay(1); - } - if (time == timeout) { - retval = -ETIMEDOUT; + retval = readl_poll_timeout_atomic(regs + RCAR_USB3_DL_CTRL, + val, !(val & RCAR_USB3_DL_CTRL_FW_SET_DATA0), + 1, 10000); + if (retval < 0) break; - } } temp = readl(regs + RCAR_USB3_DL_CTRL); temp &= ~RCAR_USB3_DL_CTRL_ENABLE; writel(temp, regs + RCAR_USB3_DL_CTRL); - for (time = 0; time < timeout; time++) { - val = readl(regs + RCAR_USB3_DL_CTRL); - if (val & RCAR_USB3_DL_CTRL_FW_SUCCESS) { - retval = 0; - break; - } - udelay(1); - } - if (time == timeout) - retval = -ETIMEDOUT; + retval = readl_poll_timeout_atomic((regs + RCAR_USB3_DL_CTRL), + val, val & RCAR_USB3_DL_CTRL_FW_SUCCESS, 1, 10000); release_firmware(fw); @@ -209,47 +169,28 @@ static int xhci_rcar_download_firmware(struct usb_hcd *hcd) static bool xhci_rcar_wait_for_pll_active(struct usb_hcd *hcd) { - int timeout = 1000; + int retval; u32 val, mask = RCAR_USB3_AXH_STA_PLL_ACTIVE_MASK; - while (timeout > 0) { - val = readl(hcd->regs + RCAR_USB3_AXH_STA); - if ((val & mask) == mask) - return true; - udelay(1); - timeout--; - } - - return false; + retval = readl_poll_timeout_atomic(hcd->regs + RCAR_USB3_AXH_STA, + val, (val & mask) == mask, 1, 1000); + return !retval; } /* This function needs to initialize a "phy" of usb before */ -int xhci_rcar_init_quirk(struct usb_hcd *hcd) +static int xhci_rcar_init_quirk(struct usb_hcd *hcd) { - struct xhci_hcd *xhci = hcd_to_xhci(hcd); - /* If hcd->regs is NULL, we don't just call the following function */ if (!hcd->regs) return 0; - /* - * On R-Car Gen2 and Gen3, the AC64 bit (bit 0) of HCCPARAMS1 is set - * to 1. However, these SoCs don't support 64-bit address memory - * pointers. So, this driver clears the AC64 bit of xhci->hcc_params - * to call dma_set_coherent_mask(dev, DMA_BIT_MASK(32)) in - * xhci_gen_setup(). - */ - if (xhci_rcar_is_gen2(hcd->self.controller) || - xhci_rcar_is_gen3(hcd->self.controller)) - xhci->quirks |= XHCI_NO_64BIT_SUPPORT; - if (!xhci_rcar_wait_for_pll_active(hcd)) return -ETIMEDOUT; return xhci_rcar_download_firmware(hcd); } -int xhci_rcar_resume_quirk(struct usb_hcd *hcd) +static int xhci_rcar_resume_quirk(struct usb_hcd *hcd) { int ret; @@ -259,3 +200,101 @@ int xhci_rcar_resume_quirk(struct usb_hcd *hcd) return ret; } + +/* + * On R-Car Gen2 and Gen3, the AC64 bit (bit 0) of HCCPARAMS1 is set + * to 1. However, these SoCs don't support 64-bit address memory + * pointers. So, this driver clears the AC64 bit of xhci->hcc_params + * to call dma_set_coherent_mask(dev, DMA_BIT_MASK(32)) in + * xhci_gen_setup() by using the XHCI_NO_64BIT_SUPPORT quirk. + * + * And, since the firmware/internal CPU control the USBSTS.STS_HALT + * and the process speed is down when the roothub port enters U3, + * long delay for the handshake of STS_HALT is neeed in xhci_suspend() + * by using the XHCI_SLOW_SUSPEND quirk. + */ +#define SET_XHCI_PLAT_PRIV_FOR_RCAR(firmware) \ + .firmware_name = firmware, \ + .quirks = XHCI_NO_64BIT_SUPPORT | XHCI_SLOW_SUSPEND, \ + .init_quirk = xhci_rcar_init_quirk, \ + .plat_start = xhci_rcar_start, \ + .resume_quirk = xhci_rcar_resume_quirk, + +static const struct xhci_plat_priv xhci_plat_renesas_rcar_gen2 = { + SET_XHCI_PLAT_PRIV_FOR_RCAR(XHCI_RCAR_FIRMWARE_NAME_V1) +}; + +static const struct xhci_plat_priv xhci_plat_renesas_rcar_gen3 = { + SET_XHCI_PLAT_PRIV_FOR_RCAR(XHCI_RCAR_FIRMWARE_NAME_V3) +}; + +static const struct xhci_plat_priv xhci_plat_renesas_rzv2m = { + .quirks = XHCI_NO_64BIT_SUPPORT | XHCI_SLOW_SUSPEND, + .init_quirk = xhci_rzv2m_init_quirk, + .plat_start = xhci_rzv2m_start, +}; + +static const struct xhci_plat_priv xhci_plat_renesas_rzg3e = { + .quirks = XHCI_NO_64BIT_SUPPORT | XHCI_RESET_ON_RESUME | XHCI_SUSPEND_RESUME_CLKS, + .plat_start = xhci_rzg3e_start, + .suspend_quirk = xhci_rzg3e_suspend, + .resume_quirk = xhci_rzg3e_resume, + .post_resume_quirk = xhci_rzg3e_post_resume, +}; + +static const struct of_device_id usb_xhci_of_match[] = { + { + .compatible = "renesas,xhci-r8a7790", + .data = &xhci_plat_renesas_rcar_gen2, + }, { + .compatible = "renesas,xhci-r8a7791", + .data = &xhci_plat_renesas_rcar_gen2, + }, { + .compatible = "renesas,xhci-r8a7793", + .data = &xhci_plat_renesas_rcar_gen2, + }, { + .compatible = "renesas,xhci-r8a7795", + .data = &xhci_plat_renesas_rcar_gen3, + }, { + .compatible = "renesas,xhci-r8a7796", + .data = &xhci_plat_renesas_rcar_gen3, + }, { + .compatible = "renesas,r9a09g047-xhci", + .data = &xhci_plat_renesas_rzg3e, + }, { + .compatible = "renesas,rcar-gen2-xhci", + .data = &xhci_plat_renesas_rcar_gen2, + }, { + .compatible = "renesas,rcar-gen3-xhci", + .data = &xhci_plat_renesas_rcar_gen3, + }, { + .compatible = "renesas,rzv2m-xhci", + .data = &xhci_plat_renesas_rzv2m, + }, + { }, +}; +MODULE_DEVICE_TABLE(of, usb_xhci_of_match); + +static int xhci_renesas_probe(struct platform_device *pdev) +{ + const struct xhci_plat_priv *priv_match; + + priv_match = of_device_get_match_data(&pdev->dev); + + return xhci_plat_probe(pdev, NULL, priv_match); +} + +static struct platform_driver usb_xhci_renesas_driver = { + .probe = xhci_renesas_probe, + .remove = xhci_plat_remove, + .shutdown = usb_hcd_platform_shutdown, + .driver = { + .name = "xhci-renesas-hcd", + .pm = &xhci_plat_pm_ops, + .of_match_table = usb_xhci_of_match, + }, +}; +module_platform_driver(usb_xhci_renesas_driver); + +MODULE_DESCRIPTION("xHCI Platform Host Controller Driver for Renesas R-Car and RZ"); +MODULE_LICENSE("GPL"); |