diff options
Diffstat (limited to 'drivers/usb/misc/Kconfig')
| -rw-r--r-- | drivers/usb/misc/Kconfig | 61 |
1 files changed, 51 insertions, 10 deletions
diff --git a/drivers/usb/misc/Kconfig b/drivers/usb/misc/Kconfig index 99b15b77dfd5..0b56b773dbdf 100644 --- a/drivers/usb/misc/Kconfig +++ b/drivers/usb/misc/Kconfig @@ -147,6 +147,7 @@ config USB_APPLEDISPLAY config USB_QCOM_EUD tristate "QCOM Embedded USB Debugger(EUD) Driver" depends on ARCH_QCOM || COMPILE_TEST + select QCOM_SCM select USB_ROLE_SWITCH help This module enables support for Qualcomm Technologies, Inc. @@ -165,6 +166,34 @@ config APPLE_MFI_FASTCHARGE It is safe to say M here. +config USB_LJCA + tristate "Intel La Jolla Cove Adapter support" + select AUXILIARY_BUS + depends on USB && ACPI + help + This adds support for Intel La Jolla Cove USB-I2C/SPI/GPIO + Master Adapter (LJCA). Additional drivers such as I2C_LJCA, + GPIO_LJCA and SPI_LJCA must be enabled in order to use the + functionality of the device. + + This driver can also be built as a module. If so, the module + will be called usb-ljca. + +config USB_USBIO + tristate "Intel USBIO Bridge support" + depends on USB && ACPI + depends on X86 || COMPILE_TEST + select AUXILIARY_BUS + help + This adds support for Intel USBIO drivers. + This enables the USBIO bridge driver module in charge to talk + to the USB device. Additional drivers such as GPIO_USBIO and + I2C_USBIO must be enabled in order to use the device's full + functionality. + + This driver can also be built as a module. If so, the module + will be called usbio. + source "drivers/usb/misc/sisusbvga/Kconfig" config USB_LD @@ -218,8 +247,8 @@ config USB_EHSET_TEST_FIXTURE VID/PID pairs. This driver then initiates a corresponding test mode on the downstream port to which the test fixture is attached. - See <http://www.usb.org/developers/onthego/EHSET_v1.01.pdf> for more - information. + See <https://www.usb.org/sites/default/files/EHSET_v1.01%281%29.pdf> + for more information. config USB_ISIGHTFW tristate "iSight firmware loading support" @@ -303,18 +332,30 @@ config BRCM_USB_PINMAP signals, which are typically on dedicated pins on the chip, to any gpio. -config USB_ONBOARD_HUB - tristate "Onboard USB hub support" +config USB_ONBOARD_DEV + tristate "Onboard USB device support" depends on OF help - Say Y here if you want to support discrete onboard USB hubs that - don't require an additional control bus for initialization, but - need some non-trivial form of initialization, such as enabling a - power regulator. An example for such a hub is the Realtek - RTS5411. + Say Y here if you want to support discrete onboard USB devices + that don't require an additional control bus for initialization, + but need some non-trivial form of initialization, such as + enabling a power regulator. An example for such device is the + Realtek RTS5411 hub. This driver can be used as a module but its state (module vs builtin) must match the state of the USB subsystem. Enabling this config will enable the driver and it will automatically match the state of the USB subsystem. If this driver is a - module it will be called onboard_usb_hub. + module it will be called onboard_usb_dev. + +config USB_ONBOARD_DEV_USB5744 + bool "Onboard USB Microchip usb5744 hub with SMBus support" + depends on (USB_ONBOARD_DEV && I2C=y) || (USB_ONBOARD_DEV=m && I2C=m) + help + Say Y here if you want to support onboard USB Microchip usb5744 + hub that requires SMBus initialization. + + This options enables usb5744 i2c default initialization sequence + during hub start-up configuration stage. It is must to enable this + option on AMD Kria KR260 Robotics Starter Kit as this hub is + connected to USB-SD converter which mounts the root filesystem. |