diff options
Diffstat (limited to 'drivers/usb/mtu3/mtu3.h')
| -rw-r--r-- | drivers/usb/mtu3/mtu3.h | 88 |
1 files changed, 45 insertions, 43 deletions
diff --git a/drivers/usb/mtu3/mtu3.h b/drivers/usb/mtu3/mtu3.h index d49db92ab26c..ba5a63669e5f 100644 --- a/drivers/usb/mtu3/mtu3.h +++ b/drivers/usb/mtu3/mtu3.h @@ -10,17 +10,20 @@ #ifndef __MTU3_H__ #define __MTU3_H__ +#include <linux/clk.h> #include <linux/device.h> #include <linux/dmapool.h> #include <linux/extcon.h> #include <linux/interrupt.h> #include <linux/list.h> +#include <linux/of.h> #include <linux/phy/phy.h> #include <linux/regulator/consumer.h> #include <linux/usb.h> #include <linux/usb/ch9.h> #include <linux/usb/gadget.h> #include <linux/usb/otg.h> +#include <linux/usb/role.h> struct mtu3; struct mtu3_ep; @@ -62,7 +65,7 @@ struct mtu3_request; #define MTU3_U3_IP_SLOT_DEFAULT 2 #define MTU3_U2_IP_SLOT_DEFAULT 1 -/** +/* * IP TRUNK version * from 0x1003 version, USB3 Gen2 is supported, two changes affect driver: * 1. MAXPKT and MULTI bits layout of TXCSR1 and RXCSR1 are adjusted, @@ -71,9 +74,9 @@ struct mtu3_request; */ #define MTU3_TRUNK_VERS_1003 0x1003 -/** +/* * Normally the device works on HS or SS, to simplify fifo management, - * devide fifo into some 512B parts, use bitmap to manage it; And + * divide fifo into some 512B parts, use bitmap to manage it; And * 128 bits size of bitmap is large enough, that means it can manage * up to 64KB fifo size. * NOTE: MTU3_EP_FIFO_UNIT should be power of two @@ -82,12 +85,14 @@ struct mtu3_request; #define MTU3_FIFO_BIT_SIZE 128 #define MTU3_U2_IP_EP0_FIFO_SIZE 64 -/** +/* * Maximum size of ep0 response buffer for ch9 requests, * the SET_SEL request uses 6 so far, and GET_STATUS is 2 */ #define EP0_RESPONSE_BUF 6 +#define BULK_CLKS_CNT 6 + /* device operated link and speed got from DEVICE_CONF register */ enum mtu3_speed { MTU3_SPEED_INACTIVE = 0, @@ -98,6 +103,7 @@ enum mtu3_speed { }; /** + * enum mtu3_g_ep0_state - endpoint 0 states * @MU3D_EP0_STATE_SETUP: waits for SETUP or received a SETUP * without data stage. * @MU3D_EP0_STATE_TX: IN data stage @@ -116,11 +122,12 @@ enum mtu3_g_ep0_state { }; /** - * MTU3_DR_FORCE_NONE: automatically switch host and periperal mode + * enum mtu3_dr_force_mode - indicates host/OTG operating mode + * @MTU3_DR_FORCE_NONE: automatically switch host and peripheral mode * by IDPIN signal. - * MTU3_DR_FORCE_HOST: force to enter host mode and override OTG + * @MTU3_DR_FORCE_HOST: force to enter host mode and override OTG * IDPIN signal. - * MTU3_DR_FORCE_DEVICE: force to enter peripheral mode. + * @MTU3_DR_FORCE_DEVICE: force to enter peripheral mode. */ enum mtu3_dr_force_mode { MTU3_DR_FORCE_NONE = 0, @@ -129,6 +136,7 @@ enum mtu3_dr_force_mode { }; /** + * struct mtu3_fifo_info - HW FIFO description and management data * @base: the base address of fifo * @limit: the bitmap size in bits * @bitmap: fifo bitmap in unit of @MTU3_EP_FIFO_UNIT @@ -140,7 +148,7 @@ struct mtu3_fifo_info { }; /** - * General Purpose Descriptor (GPD): + * struct qmu_gpd - General Purpose Descriptor (GPD): * The format of TX GPD is a little different from RX one. * And the size of GPD is 16 bytes. * @@ -174,11 +182,13 @@ struct qmu_gpd { } __packed; /** -* dma: physical base address of GPD segment -* start: virtual base address of GPD segment -* end: the last GPD element -* enqueue: the first empty GPD to use -* dequeue: the first completed GPD serviced by ISR +* struct mtu3_gpd_ring - GPD ring descriptor +* @dma: physical base address of GPD segment +* @start: virtual base address of GPD segment +* @end: the last GPD element +* @enqueue: the first empty GPD to use +* @dequeue: the first completed GPD serviced by ISR +* * NOTE: the size of GPD ring should be >= 2 */ struct mtu3_gpd_ring { @@ -190,15 +200,13 @@ struct mtu3_gpd_ring { }; /** +* struct otg_switch_mtk - OTG/dual-role switch management * @vbus: vbus 5V used by host mode * @edev: external connector used to detect vbus and iddig changes -* @vbus_nb: notifier for vbus detection -* @vbus_work : work of vbus detection notifier, used to avoid sleep in -* notifier callback which is atomic context -* @vbus_event : event of vbus detecion notifier * @id_nb : notifier for iddig(idpin) detection -* @id_work : work of iddig detection notifier -* @id_event : event of iddig detecion notifier +* @dr_work : work for drd mode switch, used to avoid sleep in atomic context +* @desired_role : role desired to switch +* @default_role : default mode while usb role is USB_ROLE_NONE * @role_sw : use USB Role Switch to support dual-role switch, can't use * extcon at the same time, and extcon is deprecated. * @role_sw_used : true when the USB Role Switch is used. @@ -209,12 +217,10 @@ struct mtu3_gpd_ring { struct otg_switch_mtk { struct regulator *vbus; struct extcon_dev *edev; - struct notifier_block vbus_nb; - struct work_struct vbus_work; - unsigned long vbus_event; struct notifier_block id_nb; - struct work_struct id_work; - unsigned long id_event; + struct work_struct dr_work; + enum usb_role desired_role; + enum usb_role default_role; struct usb_role_switch *role_sw; bool role_sw_used; bool is_u3_drd; @@ -222,17 +228,17 @@ struct otg_switch_mtk { }; /** + * struct ssusb_mtk - SuperSpeed USB descriptor (MTK) * @mac_base: register base address of device MAC, exclude xHCI's * @ippc_base: register base address of IP Power and Clock interface (IPPC) * @vusb33: usb3.3V shared by device/host IP - * @sys_clk: system clock of mtu3, shared by device/host IP - * @ref_clk: reference clock - * @mcu_clk: mcu_bus_ck clock for AHB bus etc - * @dma_clk: dma_bus_ck clock for AXI bus etc * @dr_mode: works in which mode: * host only, device only or dual-role mode * @u2_ports: number of usb2.0 host ports * @u3_ports: number of usb3.0 host ports + * @u2p_dis_msk: mask of disabling usb2 ports, e.g. bit0==1 to + * disable u2port0, bit1==1 to disable u2port1,... etc, + * but when use dual-role mode, can't disable u2port0 * @u3p_dis_msk: mask of disabling usb3 ports, for example, bit0==1 to * disable u3port0, bit1==1 to disable u3port1,... etc * @dbgfs_root: only used when supports manual dual-role switch via debugfs @@ -248,18 +254,17 @@ struct ssusb_mtk { void __iomem *ippc_base; struct phy **phys; int num_phys; + int wakeup_irq; /* common power & clock */ struct regulator *vusb33; - struct clk *sys_clk; - struct clk *ref_clk; - struct clk *mcu_clk; - struct clk *dma_clk; + struct clk_bulk_data clks[BULK_CLKS_CNT]; /* otg */ struct otg_switch_mtk otg_switch; enum usb_dr_mode dr_mode; bool is_host; int u2_ports; int u3_ports; + int u2p_dis_msk; int u3p_dis_msk; struct dentry *dbgfs_root; /* usb wakeup for host mode */ @@ -270,6 +275,7 @@ struct ssusb_mtk { }; /** + * struct mtu3_ep - common mtu3 endpoint description * @fifo_size: it is (@slot + 1) * @fifo_seg_size * @fifo_seg_size: it is roundup_pow_of_two(@maxp) */ @@ -293,8 +299,6 @@ struct mtu3_ep { const struct usb_endpoint_descriptor *desc; int flags; - u8 wedged; - u8 busy; }; struct mtu3_request { @@ -322,6 +326,7 @@ static inline struct ssusb_mtk *dev_to_ssusb(struct device *dev) * @ep0_req: dummy request used while handling standard USB requests * for GET_STATUS and SET_SEL * @setup_buf: ep0 response buffer for GET_STATUS and SET_SEL requests + * @u3_capable: is capable of supporting USB3 */ struct mtu3 { spinlock_t lock; @@ -348,7 +353,8 @@ struct mtu3 { struct usb_gadget_driver *gadget_driver; struct mtu3_request ep0_req; u8 setup_buf[EP0_RESPONSE_BUF]; - u32 max_speed; + enum usb_device_speed max_speed; + enum usb_device_speed speed; unsigned is_active:1; unsigned may_wakeup:1; @@ -357,9 +363,12 @@ struct mtu3 { unsigned softconnect:1; unsigned u1_enable:1; unsigned u2_enable:1; - unsigned is_u3_ip:1; + unsigned u3_capable:1; unsigned delayed_status:1; unsigned gen2cp:1; + unsigned connected:1; + unsigned async_callbacks:1; + unsigned separate_fifo:1; u8 address; u8 test_mode_nr; @@ -371,12 +380,6 @@ static inline struct mtu3 *gadget_to_mtu3(struct usb_gadget *g) return container_of(g, struct mtu3, g); } -static inline int is_first_entry(const struct list_head *list, - const struct list_head *head) -{ - return list_is_last(head, list); -} - static inline struct mtu3_request *to_mtu3_request(struct usb_request *req) { return req ? container_of(req, struct mtu3_request, request) : NULL; @@ -429,7 +432,6 @@ int mtu3_config_ep(struct mtu3 *mtu, struct mtu3_ep *mep, int interval, int burst, int mult); void mtu3_deconfig_ep(struct mtu3 *mtu, struct mtu3_ep *mep); void mtu3_ep_stall_set(struct mtu3_ep *mep, bool set); -void mtu3_ep0_setup(struct mtu3 *mtu); void mtu3_start(struct mtu3 *mtu); void mtu3_stop(struct mtu3 *mtu); void mtu3_dev_on_off(struct mtu3 *mtu, int is_on); |