diff options
Diffstat (limited to 'include/uapi/linux/ethtool.h')
| -rw-r--r-- | include/uapi/linux/ethtool.h | 1911 |
1 files changed, 1703 insertions, 208 deletions
diff --git a/include/uapi/linux/ethtool.h b/include/uapi/linux/ethtool.h index 38dbafaa5341..eb7ff2602fbb 100644 --- a/include/uapi/linux/ethtool.h +++ b/include/uapi/linux/ethtool.h @@ -1,3 +1,4 @@ +/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */ /* * ethtool.h: Defines for Linux ethtool. * @@ -13,48 +14,118 @@ #ifndef _UAPI_LINUX_ETHTOOL_H #define _UAPI_LINUX_ETHTOOL_H +#include <linux/const.h> #include <linux/types.h> #include <linux/if_ether.h> -/* This should work for both 32 and 64 bit userland. */ +#ifndef __KERNEL__ +#include <limits.h> /* for INT_MAX */ +#endif + +/* All structures exposed to userland should be defined such that they + * have the same layout for 32-bit and 64-bit userland. + */ + +/* Note on reserved space. + * Reserved fields must not be accessed directly by user space because + * they may be replaced by a different field in the future. They must + * be initialized to zero before making the request, e.g. via memset + * of the entire structure or implicitly by not being set in a structure + * initializer. + */ + +/** + * struct ethtool_cmd - DEPRECATED, link control and status + * This structure is DEPRECATED, please use struct ethtool_link_settings. + * @cmd: Command number = %ETHTOOL_GSET or %ETHTOOL_SSET + * @supported: Bitmask of %SUPPORTED_* flags for the link modes, + * physical connectors and other link features for which the + * interface supports autonegotiation or auto-detection. + * Read-only. + * @advertising: Bitmask of %ADVERTISED_* flags for the link modes, + * physical connectors and other link features that are + * advertised through autonegotiation or enabled for + * auto-detection. + * @speed: Low bits of the speed, 1Mb units, 0 to INT_MAX or SPEED_UNKNOWN + * @duplex: Duplex mode; one of %DUPLEX_* + * @port: Physical connector type; one of %PORT_* + * @phy_address: MDIO address of PHY (transceiver); 0 or 255 if not + * applicable. For clause 45 PHYs this is the PRTAD. + * @transceiver: Historically used to distinguish different possible + * PHY types, but not in a consistent way. Deprecated. + * @autoneg: Enable/disable autonegotiation and auto-detection; + * either %AUTONEG_DISABLE or %AUTONEG_ENABLE + * @mdio_support: Bitmask of %ETH_MDIO_SUPPORTS_* flags for the MDIO + * protocols supported by the interface; 0 if unknown. + * Read-only. + * @maxtxpkt: Historically used to report TX IRQ coalescing; now + * obsoleted by &struct ethtool_coalesce. Read-only; deprecated. + * @maxrxpkt: Historically used to report RX IRQ coalescing; now + * obsoleted by &struct ethtool_coalesce. Read-only; deprecated. + * @speed_hi: High bits of the speed, 1Mb units, 0 to INT_MAX or SPEED_UNKNOWN + * @eth_tp_mdix: Ethernet twisted-pair MDI(-X) status; one of + * %ETH_TP_MDI_*. If the status is unknown or not applicable, the + * value will be %ETH_TP_MDI_INVALID. Read-only. + * @eth_tp_mdix_ctrl: Ethernet twisted pair MDI(-X) control; one of + * %ETH_TP_MDI_*. If MDI(-X) control is not implemented, reads + * yield %ETH_TP_MDI_INVALID and writes may be ignored or rejected. + * When written successfully, the link should be renegotiated if + * necessary. + * @lp_advertising: Bitmask of %ADVERTISED_* flags for the link modes + * and other link features that the link partner advertised + * through autonegotiation; 0 if unknown or not applicable. + * Read-only. + * @reserved: Reserved for future use; see the note on reserved space. + * + * The link speed in Mbps is split between @speed and @speed_hi. Use + * the ethtool_cmd_speed() and ethtool_cmd_speed_set() functions to + * access it. + * + * If autonegotiation is disabled, the speed and @duplex represent the + * fixed link mode and are writable if the driver supports multiple + * link modes. If it is enabled then they are read-only; if the link + * is up they represent the negotiated link mode; if the link is down, + * the speed is 0, %SPEED_UNKNOWN or the highest enabled speed and + * @duplex is %DUPLEX_UNKNOWN or the best enabled duplex mode. + * + * Some hardware interfaces may have multiple PHYs and/or physical + * connectors fitted or do not allow the driver to detect which are + * fitted. For these interfaces @port and/or @phy_address may be + * writable, possibly dependent on @autoneg being %AUTONEG_DISABLE. + * Otherwise, attempts to write different values may be ignored or + * rejected. + * + * Users should assume that all fields not marked read-only are + * writable and subject to validation by the driver. They should use + * %ETHTOOL_GSET to get the current values before making specific + * changes and then applying them with %ETHTOOL_SSET. + * + * Deprecated fields should be ignored by both users and drivers. + */ struct ethtool_cmd { __u32 cmd; - __u32 supported; /* Features this interface supports */ - __u32 advertising; /* Features this interface advertises */ - __u16 speed; /* The forced speed (lower bits) in - * Mbps. Please use - * ethtool_cmd_speed()/_set() to - * access it */ - __u8 duplex; /* Duplex, half or full */ - __u8 port; /* Which connector port */ - __u8 phy_address; /* MDIO PHY address (PRTAD for clause 45). - * May be read-only or read-write - * depending on the driver. - */ - __u8 transceiver; /* Which transceiver to use */ - __u8 autoneg; /* Enable or disable autonegotiation */ - __u8 mdio_support; /* MDIO protocols supported. Read-only. - * Not set by all drivers. - */ - __u32 maxtxpkt; /* Tx pkts before generating tx int */ - __u32 maxrxpkt; /* Rx pkts before generating rx int */ - __u16 speed_hi; /* The forced speed (upper - * bits) in Mbps. Please use - * ethtool_cmd_speed()/_set() to - * access it */ - __u8 eth_tp_mdix; /* twisted pair MDI-X status */ - __u8 eth_tp_mdix_ctrl; /* twisted pair MDI-X control, when set, - * link should be renegotiated if necessary - */ - __u32 lp_advertising; /* Features the link partner advertises */ + __u32 supported; + __u32 advertising; + __u16 speed; + __u8 duplex; + __u8 port; + __u8 phy_address; + __u8 transceiver; + __u8 autoneg; + __u8 mdio_support; + __u32 maxtxpkt; + __u32 maxrxpkt; + __u16 speed_hi; + __u8 eth_tp_mdix; + __u8 eth_tp_mdix_ctrl; + __u32 lp_advertising; __u32 reserved[2]; }; static inline void ethtool_cmd_speed_set(struct ethtool_cmd *ep, __u32 speed) { - - ep->speed = (__u16)speed; + ep->speed = (__u16)(speed & 0xFFFF); ep->speed_hi = (__u16)(speed >> 16); } @@ -79,37 +150,69 @@ static inline __u32 ethtool_cmd_speed(const struct ethtool_cmd *ep) #define ETHTOOL_FWVERS_LEN 32 #define ETHTOOL_BUSINFO_LEN 32 -/* these strings are set to whatever the driver author decides... */ +#define ETHTOOL_EROMVERS_LEN 32 + +/** + * struct ethtool_drvinfo - general driver and device information + * @cmd: Command number = %ETHTOOL_GDRVINFO + * @driver: Driver short name. This should normally match the name + * in its bus driver structure (e.g. pci_driver::name). Must + * not be an empty string. + * @version: Driver version string; may be an empty string + * @fw_version: Firmware version string; driver defined; may be an + * empty string + * @erom_version: Expansion ROM version string; driver defined; may be + * an empty string + * @bus_info: Device bus address. This should match the dev_name() + * string for the underlying bus device, if there is one. May be + * an empty string. + * @reserved2: Reserved for future use; see the note on reserved space. + * @n_priv_flags: Number of flags valid for %ETHTOOL_GPFLAGS and + * %ETHTOOL_SPFLAGS commands; also the number of strings in the + * %ETH_SS_PRIV_FLAGS set + * @n_stats: Number of u64 statistics returned by the %ETHTOOL_GSTATS + * command; also the number of strings in the %ETH_SS_STATS set + * @testinfo_len: Number of results returned by the %ETHTOOL_TEST + * command; also the number of strings in the %ETH_SS_TEST set + * @eedump_len: Size of EEPROM accessible through the %ETHTOOL_GEEPROM + * and %ETHTOOL_SEEPROM commands, in bytes + * @regdump_len: Size of register dump returned by the %ETHTOOL_GREGS + * command, in bytes + * + * Users can use the %ETHTOOL_GSSET_INFO command to get the number of + * strings in any string set (from Linux 2.6.34). + */ struct ethtool_drvinfo { __u32 cmd; - char driver[32]; /* driver short name, "tulip", "eepro100" */ - char version[32]; /* driver version string */ - char fw_version[ETHTOOL_FWVERS_LEN]; /* firmware version string */ - char bus_info[ETHTOOL_BUSINFO_LEN]; /* Bus info for this IF. */ - /* For PCI devices, use pci_name(pci_dev). */ - char reserved1[32]; + char driver[32]; + char version[32]; + char fw_version[ETHTOOL_FWVERS_LEN]; + char bus_info[ETHTOOL_BUSINFO_LEN]; + char erom_version[ETHTOOL_EROMVERS_LEN]; char reserved2[12]; - /* - * Some struct members below are filled in - * using ops->get_sset_count(). Obtaining - * this info from ethtool_drvinfo is now - * deprecated; Use ETHTOOL_GSSET_INFO - * instead. - */ - __u32 n_priv_flags; /* number of flags valid in ETHTOOL_GPFLAGS */ - __u32 n_stats; /* number of u64's from ETHTOOL_GSTATS */ + __u32 n_priv_flags; + __u32 n_stats; __u32 testinfo_len; - __u32 eedump_len; /* Size of data from ETHTOOL_GEEPROM (bytes) */ - __u32 regdump_len; /* Size of data from ETHTOOL_GREGS (bytes) */ + __u32 eedump_len; + __u32 regdump_len; }; #define SOPASS_MAX 6 -/* wake-on-lan settings */ + +/** + * struct ethtool_wolinfo - Wake-On-Lan configuration + * @cmd: Command number = %ETHTOOL_GWOL or %ETHTOOL_SWOL + * @supported: Bitmask of %WAKE_* flags for supported Wake-On-Lan modes. + * Read-only. + * @wolopts: Bitmask of %WAKE_* flags for enabled Wake-On-Lan modes. + * @sopass: SecureOn(tm) password; meaningful only if %WAKE_MAGICSECURE + * is set in @wolopts. + */ struct ethtool_wolinfo { __u32 cmd; __u32 supported; __u32 wolopts; - __u8 sopass[SOPASS_MAX]; /* SecureOn(tm) password */ + __u8 sopass[SOPASS_MAX]; }; /* for passing single values */ @@ -118,21 +221,132 @@ struct ethtool_value { __u32 data; }; -/* for passing big chunks of data */ +#define PFC_STORM_PREVENTION_AUTO 0xffff +#define PFC_STORM_PREVENTION_DISABLE 0 + +enum tunable_id { + ETHTOOL_ID_UNSPEC, + ETHTOOL_RX_COPYBREAK, + ETHTOOL_TX_COPYBREAK, + ETHTOOL_PFC_PREVENTION_TOUT, /* timeout in msecs */ + ETHTOOL_TX_COPYBREAK_BUF_SIZE, + /* + * Add your fresh new tunable attribute above and remember to update + * tunable_strings[] in net/ethtool/common.c + */ + __ETHTOOL_TUNABLE_COUNT, +}; + +enum tunable_type_id { + ETHTOOL_TUNABLE_UNSPEC, + ETHTOOL_TUNABLE_U8, + ETHTOOL_TUNABLE_U16, + ETHTOOL_TUNABLE_U32, + ETHTOOL_TUNABLE_U64, + ETHTOOL_TUNABLE_STRING, + ETHTOOL_TUNABLE_S8, + ETHTOOL_TUNABLE_S16, + ETHTOOL_TUNABLE_S32, + ETHTOOL_TUNABLE_S64, +}; + +struct ethtool_tunable { + __u32 cmd; + __u32 id; + __u32 type_id; + __u32 len; + void *data[]; +}; + +#define DOWNSHIFT_DEV_DEFAULT_COUNT 0xff +#define DOWNSHIFT_DEV_DISABLE 0 + +/* Time in msecs after which link is reported as down + * 0 = lowest time supported by the PHY + * 0xff = off, link down detection according to standard + */ +#define ETHTOOL_PHY_FAST_LINK_DOWN_ON 0 +#define ETHTOOL_PHY_FAST_LINK_DOWN_OFF 0xff + +/* Energy Detect Power Down (EDPD) is a feature supported by some PHYs, where + * the PHY's RX & TX blocks are put into a low-power mode when there is no + * link detected (typically cable is un-plugged). For RX, only a minimal + * link-detection is available, and for TX the PHY wakes up to send link pulses + * to avoid any lock-ups in case the peer PHY may also be running in EDPD mode. + * + * Some PHYs may support configuration of the wake-up interval for TX pulses, + * and some PHYs may support only disabling TX pulses entirely. For the latter + * a special value is required (ETHTOOL_PHY_EDPD_NO_TX) so that this can be + * configured from userspace (should the user want it). + * + * The interval units for TX wake-up are in milliseconds, since this should + * cover a reasonable range of intervals: + * - from 1 millisecond, which does not sound like much of a power-saver + * - to ~65 seconds which is quite a lot to wait for a link to come up when + * plugging a cable + */ +#define ETHTOOL_PHY_EDPD_DFLT_TX_MSECS 0xffff +#define ETHTOOL_PHY_EDPD_NO_TX 0xfffe +#define ETHTOOL_PHY_EDPD_DISABLE 0 + +enum phy_tunable_id { + ETHTOOL_PHY_ID_UNSPEC, + ETHTOOL_PHY_DOWNSHIFT, + ETHTOOL_PHY_FAST_LINK_DOWN, + ETHTOOL_PHY_EDPD, + /* + * Add your fresh new phy tunable attribute above and remember to update + * phy_tunable_strings[] in net/ethtool/common.c + */ + __ETHTOOL_PHY_TUNABLE_COUNT, +}; + +/** + * struct ethtool_regs - hardware register dump + * @cmd: Command number = %ETHTOOL_GREGS + * @version: Dump format version. This is driver-specific and may + * distinguish different chips/revisions. Drivers must use new + * version numbers whenever the dump format changes in an + * incompatible way. + * @len: On entry, the real length of @data. On return, the number of + * bytes used. + * @data: Buffer for the register dump + * + * Users should use %ETHTOOL_GDRVINFO to find the maximum length of + * a register dump for the interface. They must allocate the buffer + * immediately following this structure. + */ struct ethtool_regs { __u32 cmd; - __u32 version; /* driver-specific, indicates different chips/revs */ - __u32 len; /* bytes */ - __u8 data[0]; + __u32 version; + __u32 len; + __u8 data[]; }; -/* for passing EEPROM chunks */ +/** + * struct ethtool_eeprom - EEPROM dump + * @cmd: Command number = %ETHTOOL_GEEPROM, %ETHTOOL_GMODULEEEPROM or + * %ETHTOOL_SEEPROM + * @magic: A 'magic cookie' value to guard against accidental changes. + * The value passed in to %ETHTOOL_SEEPROM must match the value + * returned by %ETHTOOL_GEEPROM for the same device. This is + * unused when @cmd is %ETHTOOL_GMODULEEEPROM. + * @offset: Offset within the EEPROM to begin reading/writing, in bytes + * @len: On entry, number of bytes to read/write. On successful + * return, number of bytes actually read/written. In case of + * error, this may indicate at what point the error occurred. + * @data: Buffer to read/write from + * + * Users may use %ETHTOOL_GDRVINFO or %ETHTOOL_GMODULEINFO to find + * the length of an on-board or module EEPROM, respectively. They + * must allocate the buffer immediately following this structure. + */ struct ethtool_eeprom { __u32 cmd; __u32 magic; - __u32 offset; /* in bytes */ - __u32 len; /* in bytes */ - __u8 data[0]; + __u32 offset; + __u32 len; + __u8 data[]; }; /** @@ -151,6 +365,7 @@ struct ethtool_eeprom { * @tx_lpi_timer: Time in microseconds the interface delays prior to asserting * its tx lpi (after reaching 'idle' state). Effective only when eee * was negotiated and tx_lpi_enabled was set. + * @reserved: Reserved for future use; see the note on reserved space. */ struct ethtool_eee { __u32 cmd; @@ -169,6 +384,7 @@ struct ethtool_eee { * @cmd: %ETHTOOL_GMODULEINFO * @type: Standard the module information conforms to %ETH_MODULE_SFF_xxxx * @eeprom_len: Length of the eeprom + * @reserved: Reserved for future use; see the note on reserved space. * * This structure is used to return the information to * properly size memory for a subsequent call to %ETHTOOL_GMODULEEEPROM. @@ -229,17 +445,18 @@ struct ethtool_modinfo { * @rate_sample_interval: How often to do adaptive coalescing packet rate * sampling, measured in seconds. Must not be zero. * - * Each pair of (usecs, max_frames) fields specifies this exit - * condition for interrupt coalescing: + * Each pair of (usecs, max_frames) fields specifies that interrupts + * should be coalesced until * (usecs > 0 && time_since_first_completion >= usecs) || * (max_frames > 0 && completed_frames >= max_frames) + * * It is illegal to set both usecs and max_frames to zero as this * would cause interrupts to never be generated. To disable * coalescing, set usecs = 0 and max_frames = 1. * * Some implementations ignore the value of max_frames and use the - * condition: - * time_since_first_completion >= usecs + * condition time_since_first_completion >= usecs + * * This is deprecated. Drivers for hardware that does not support * counting completions should validate that max_frames == !rx_usecs. * @@ -279,22 +496,37 @@ struct ethtool_coalesce { __u32 rate_sample_interval; }; -/* for configuring RX/TX ring parameters */ +/** + * struct ethtool_ringparam - RX/TX ring parameters + * @cmd: Command number = %ETHTOOL_GRINGPARAM or %ETHTOOL_SRINGPARAM + * @rx_max_pending: Maximum supported number of pending entries per + * RX ring. Read-only. + * @rx_mini_max_pending: Maximum supported number of pending entries + * per RX mini ring. Read-only. + * @rx_jumbo_max_pending: Maximum supported number of pending entries + * per RX jumbo ring. Read-only. + * @tx_max_pending: Maximum supported number of pending entries per + * TX ring. Read-only. + * @rx_pending: Current maximum number of pending entries per RX ring + * @rx_mini_pending: Current maximum number of pending entries per RX + * mini ring + * @rx_jumbo_pending: Current maximum number of pending entries per RX + * jumbo ring + * @tx_pending: Current maximum supported number of pending entries + * per TX ring + * + * If the interface does not have separate RX mini and/or jumbo rings, + * @rx_mini_max_pending and/or @rx_jumbo_max_pending will be 0. + * + * There may also be driver-dependent minimum values for the number + * of entries per ring. + */ struct ethtool_ringparam { - __u32 cmd; /* ETHTOOL_{G,S}RINGPARAM */ - - /* Read only attributes. These indicate the maximum number - * of pending RX/TX ring entries the driver will allow the - * user to set. - */ + __u32 cmd; __u32 rx_max_pending; __u32 rx_mini_max_pending; __u32 rx_jumbo_max_pending; __u32 tx_max_pending; - - /* Values changeable by the user. The valid values are - * in the range 1 to the "*_max_pending" counterpart above. - */ __u32 rx_pending; __u32 rx_mini_pending; __u32 rx_jumbo_pending; @@ -329,51 +561,577 @@ struct ethtool_channels { __u32 combined_count; }; -/* for configuring link flow control parameters */ +/** + * struct ethtool_pauseparam - Ethernet pause (flow control) parameters + * @cmd: Command number = %ETHTOOL_GPAUSEPARAM or %ETHTOOL_SPAUSEPARAM + * @autoneg: Flag to enable autonegotiation of pause frame use + * @rx_pause: Flag to enable reception of pause frames + * @tx_pause: Flag to enable transmission of pause frames + * + * Drivers should reject a non-zero setting of @autoneg when + * autoneogotiation is disabled (or not supported) for the link. + * + * If the link is autonegotiated, drivers should use + * mii_advertise_flowctrl() or similar code to set the advertised + * pause frame capabilities based on the @rx_pause and @tx_pause flags, + * even if @autoneg is zero. They should also allow the advertised + * pause frame capabilities to be controlled directly through the + * advertising field of &struct ethtool_cmd. + * + * If @autoneg is non-zero, the MAC is configured to send and/or + * receive pause frames according to the result of autonegotiation. + * Otherwise, it is configured directly based on the @rx_pause and + * @tx_pause flags. + */ struct ethtool_pauseparam { - __u32 cmd; /* ETHTOOL_{G,S}PAUSEPARAM */ - - /* If the link is being auto-negotiated (via ethtool_cmd.autoneg - * being true) the user may set 'autoneg' here non-zero to have the - * pause parameters be auto-negotiated too. In such a case, the - * {rx,tx}_pause values below determine what capabilities are - * advertised. - * - * If 'autoneg' is zero or the link is not being auto-negotiated, - * then {rx,tx}_pause force the driver to use/not-use pause - * flow control. - */ + __u32 cmd; __u32 autoneg; __u32 rx_pause; __u32 tx_pause; }; +/* Link extended state */ +enum ethtool_link_ext_state { + ETHTOOL_LINK_EXT_STATE_AUTONEG, + ETHTOOL_LINK_EXT_STATE_LINK_TRAINING_FAILURE, + ETHTOOL_LINK_EXT_STATE_LINK_LOGICAL_MISMATCH, + ETHTOOL_LINK_EXT_STATE_BAD_SIGNAL_INTEGRITY, + ETHTOOL_LINK_EXT_STATE_NO_CABLE, + ETHTOOL_LINK_EXT_STATE_CABLE_ISSUE, + ETHTOOL_LINK_EXT_STATE_EEPROM_ISSUE, + ETHTOOL_LINK_EXT_STATE_CALIBRATION_FAILURE, + ETHTOOL_LINK_EXT_STATE_POWER_BUDGET_EXCEEDED, + ETHTOOL_LINK_EXT_STATE_OVERHEAT, + ETHTOOL_LINK_EXT_STATE_MODULE, +}; + +/* More information in addition to ETHTOOL_LINK_EXT_STATE_AUTONEG. */ +enum ethtool_link_ext_substate_autoneg { + ETHTOOL_LINK_EXT_SUBSTATE_AN_NO_PARTNER_DETECTED = 1, + ETHTOOL_LINK_EXT_SUBSTATE_AN_ACK_NOT_RECEIVED, + ETHTOOL_LINK_EXT_SUBSTATE_AN_NEXT_PAGE_EXCHANGE_FAILED, + ETHTOOL_LINK_EXT_SUBSTATE_AN_NO_PARTNER_DETECTED_FORCE_MODE, + ETHTOOL_LINK_EXT_SUBSTATE_AN_FEC_MISMATCH_DURING_OVERRIDE, + ETHTOOL_LINK_EXT_SUBSTATE_AN_NO_HCD, +}; + +/* More information in addition to ETHTOOL_LINK_EXT_STATE_LINK_TRAINING_FAILURE. + */ +enum ethtool_link_ext_substate_link_training { + ETHTOOL_LINK_EXT_SUBSTATE_LT_KR_FRAME_LOCK_NOT_ACQUIRED = 1, + ETHTOOL_LINK_EXT_SUBSTATE_LT_KR_LINK_INHIBIT_TIMEOUT, + ETHTOOL_LINK_EXT_SUBSTATE_LT_KR_LINK_PARTNER_DID_NOT_SET_RECEIVER_READY, + ETHTOOL_LINK_EXT_SUBSTATE_LT_REMOTE_FAULT, +}; + +/* More information in addition to ETHTOOL_LINK_EXT_STATE_LINK_LOGICAL_MISMATCH. + */ +enum ethtool_link_ext_substate_link_logical_mismatch { + ETHTOOL_LINK_EXT_SUBSTATE_LLM_PCS_DID_NOT_ACQUIRE_BLOCK_LOCK = 1, + ETHTOOL_LINK_EXT_SUBSTATE_LLM_PCS_DID_NOT_ACQUIRE_AM_LOCK, + ETHTOOL_LINK_EXT_SUBSTATE_LLM_PCS_DID_NOT_GET_ALIGN_STATUS, + ETHTOOL_LINK_EXT_SUBSTATE_LLM_FC_FEC_IS_NOT_LOCKED, + ETHTOOL_LINK_EXT_SUBSTATE_LLM_RS_FEC_IS_NOT_LOCKED, +}; + +/* More information in addition to ETHTOOL_LINK_EXT_STATE_BAD_SIGNAL_INTEGRITY. + */ +enum ethtool_link_ext_substate_bad_signal_integrity { + ETHTOOL_LINK_EXT_SUBSTATE_BSI_LARGE_NUMBER_OF_PHYSICAL_ERRORS = 1, + ETHTOOL_LINK_EXT_SUBSTATE_BSI_UNSUPPORTED_RATE, + ETHTOOL_LINK_EXT_SUBSTATE_BSI_SERDES_REFERENCE_CLOCK_LOST, + ETHTOOL_LINK_EXT_SUBSTATE_BSI_SERDES_ALOS, +}; + +/* More information in addition to ETHTOOL_LINK_EXT_STATE_CABLE_ISSUE. */ +enum ethtool_link_ext_substate_cable_issue { + ETHTOOL_LINK_EXT_SUBSTATE_CI_UNSUPPORTED_CABLE = 1, + ETHTOOL_LINK_EXT_SUBSTATE_CI_CABLE_TEST_FAILURE, +}; + +/* More information in addition to ETHTOOL_LINK_EXT_STATE_MODULE. */ +enum ethtool_link_ext_substate_module { + ETHTOOL_LINK_EXT_SUBSTATE_MODULE_CMIS_NOT_READY = 1, +}; + #define ETH_GSTRING_LEN 32 + +/** + * enum ethtool_stringset - string set ID + * @ETH_SS_TEST: Self-test result names, for use with %ETHTOOL_TEST + * @ETH_SS_STATS: Statistic names, for use with %ETHTOOL_GSTATS + * @ETH_SS_PRIV_FLAGS: Driver private flag names, for use with + * %ETHTOOL_GPFLAGS and %ETHTOOL_SPFLAGS + * @ETH_SS_NTUPLE_FILTERS: Previously used with %ETHTOOL_GRXNTUPLE; + * now deprecated + * @ETH_SS_FEATURES: Device feature names + * @ETH_SS_RSS_HASH_FUNCS: RSS hush function names + * @ETH_SS_TUNABLES: tunable names + * @ETH_SS_PHY_STATS: Statistic names, for use with %ETHTOOL_GPHYSTATS + * @ETH_SS_PHY_TUNABLES: PHY tunable names + * @ETH_SS_LINK_MODES: link mode names + * @ETH_SS_MSG_CLASSES: debug message class names + * @ETH_SS_WOL_MODES: wake-on-lan modes + * @ETH_SS_SOF_TIMESTAMPING: SOF_TIMESTAMPING_* flags + * @ETH_SS_TS_TX_TYPES: timestamping Tx types + * @ETH_SS_TS_RX_FILTERS: timestamping Rx filters + * @ETH_SS_UDP_TUNNEL_TYPES: UDP tunnel types + * @ETH_SS_STATS_STD: standardized stats + * @ETH_SS_STATS_ETH_PHY: names of IEEE 802.3 PHY statistics + * @ETH_SS_STATS_ETH_MAC: names of IEEE 802.3 MAC statistics + * @ETH_SS_STATS_ETH_CTRL: names of IEEE 802.3 MAC Control statistics + * @ETH_SS_STATS_RMON: names of RMON statistics + * @ETH_SS_STATS_PHY: names of PHY(dev) statistics + * @ETH_SS_TS_FLAGS: hardware timestamping flags + * + * @ETH_SS_COUNT: number of defined string sets + */ enum ethtool_stringset { ETH_SS_TEST = 0, ETH_SS_STATS, ETH_SS_PRIV_FLAGS, - ETH_SS_NTUPLE_FILTERS, /* Do not use, GRXNTUPLE is now deprecated */ + ETH_SS_NTUPLE_FILTERS, ETH_SS_FEATURES, + ETH_SS_RSS_HASH_FUNCS, + ETH_SS_TUNABLES, + ETH_SS_PHY_STATS, + ETH_SS_PHY_TUNABLES, + ETH_SS_LINK_MODES, + ETH_SS_MSG_CLASSES, + ETH_SS_WOL_MODES, + ETH_SS_SOF_TIMESTAMPING, + ETH_SS_TS_TX_TYPES, + ETH_SS_TS_RX_FILTERS, + ETH_SS_UDP_TUNNEL_TYPES, + ETH_SS_STATS_STD, + ETH_SS_STATS_ETH_PHY, + ETH_SS_STATS_ETH_MAC, + ETH_SS_STATS_ETH_CTRL, + ETH_SS_STATS_RMON, + ETH_SS_STATS_PHY, + ETH_SS_TS_FLAGS, + + /* add new constants above here */ + ETH_SS_COUNT }; -/* for passing string sets for data tagging */ +/** + * enum ethtool_mac_stats_src - source of ethtool MAC statistics + * @ETHTOOL_MAC_STATS_SRC_AGGREGATE: + * if device supports a MAC merge layer, this retrieves the aggregate + * statistics of the eMAC and pMAC. Otherwise, it retrieves just the + * statistics of the single (express) MAC. + * @ETHTOOL_MAC_STATS_SRC_EMAC: + * if device supports a MM layer, this retrieves the eMAC statistics. + * Otherwise, it retrieves the statistics of the single (express) MAC. + * @ETHTOOL_MAC_STATS_SRC_PMAC: + * if device supports a MM layer, this retrieves the pMAC statistics. + */ +enum ethtool_mac_stats_src { + ETHTOOL_MAC_STATS_SRC_AGGREGATE, + ETHTOOL_MAC_STATS_SRC_EMAC, + ETHTOOL_MAC_STATS_SRC_PMAC, +}; + +/** + * enum ethtool_module_power_mode_policy - plug-in module power mode policy + * @ETHTOOL_MODULE_POWER_MODE_POLICY_HIGH: Module is always in high power mode. + * @ETHTOOL_MODULE_POWER_MODE_POLICY_AUTO: Module is transitioned by the host + * to high power mode when the first port using it is put administratively + * up and to low power mode when the last port using it is put + * administratively down. + */ +enum ethtool_module_power_mode_policy { + ETHTOOL_MODULE_POWER_MODE_POLICY_HIGH = 1, + ETHTOOL_MODULE_POWER_MODE_POLICY_AUTO, +}; + +/** + * enum ethtool_module_power_mode - plug-in module power mode + * @ETHTOOL_MODULE_POWER_MODE_LOW: Module is in low power mode. + * @ETHTOOL_MODULE_POWER_MODE_HIGH: Module is in high power mode. + */ +enum ethtool_module_power_mode { + ETHTOOL_MODULE_POWER_MODE_LOW = 1, + ETHTOOL_MODULE_POWER_MODE_HIGH, +}; + +/** + * enum ethtool_c33_pse_ext_state - groups of PSE extended states + * functions. IEEE 802.3-2022 33.2.4.4 Variables + * + * @ETHTOOL_C33_PSE_EXT_STATE_ERROR_CONDITION: Group of error_condition states + * @ETHTOOL_C33_PSE_EXT_STATE_MR_MPS_VALID: Group of mr_mps_valid states + * @ETHTOOL_C33_PSE_EXT_STATE_MR_PSE_ENABLE: Group of mr_pse_enable states + * @ETHTOOL_C33_PSE_EXT_STATE_OPTION_DETECT_TED: Group of option_detect_ted + * states + * @ETHTOOL_C33_PSE_EXT_STATE_OPTION_VPORT_LIM: Group of option_vport_lim states + * @ETHTOOL_C33_PSE_EXT_STATE_OVLD_DETECTED: Group of ovld_detected states + * @ETHTOOL_C33_PSE_EXT_STATE_PD_DLL_POWER_TYPE: Group of pd_dll_power_type + * states + * @ETHTOOL_C33_PSE_EXT_STATE_POWER_NOT_AVAILABLE: Group of power_not_available + * states + * @ETHTOOL_C33_PSE_EXT_STATE_SHORT_DETECTED: Group of short_detected states + */ +enum ethtool_c33_pse_ext_state { + ETHTOOL_C33_PSE_EXT_STATE_ERROR_CONDITION = 1, + ETHTOOL_C33_PSE_EXT_STATE_MR_MPS_VALID, + ETHTOOL_C33_PSE_EXT_STATE_MR_PSE_ENABLE, + ETHTOOL_C33_PSE_EXT_STATE_OPTION_DETECT_TED, + ETHTOOL_C33_PSE_EXT_STATE_OPTION_VPORT_LIM, + ETHTOOL_C33_PSE_EXT_STATE_OVLD_DETECTED, + ETHTOOL_C33_PSE_EXT_STATE_PD_DLL_POWER_TYPE, + ETHTOOL_C33_PSE_EXT_STATE_POWER_NOT_AVAILABLE, + ETHTOOL_C33_PSE_EXT_STATE_SHORT_DETECTED, +}; + +/** + * enum ethtool_c33_pse_ext_substate_mr_mps_valid - mr_mps_valid states + * functions. IEEE 802.3-2022 33.2.4.4 Variables + * + * @ETHTOOL_C33_PSE_EXT_SUBSTATE_MR_MPS_VALID_DETECTED_UNDERLOAD: Underload + * state + * @ETHTOOL_C33_PSE_EXT_SUBSTATE_MR_MPS_VALID_CONNECTION_OPEN: Port is not + * connected + * + * The PSE monitors either the DC or AC Maintain Power Signature + * (MPS, see 33.2.9.1). This variable indicates the presence or absence of + * a valid MPS. + */ +enum ethtool_c33_pse_ext_substate_mr_mps_valid { + ETHTOOL_C33_PSE_EXT_SUBSTATE_MR_MPS_VALID_DETECTED_UNDERLOAD = 1, + ETHTOOL_C33_PSE_EXT_SUBSTATE_MR_MPS_VALID_CONNECTION_OPEN, +}; + +/** + * enum ethtool_c33_pse_ext_substate_error_condition - error_condition states + * functions. IEEE 802.3-2022 33.2.4.4 Variables + * + * @ETHTOOL_C33_PSE_EXT_SUBSTATE_ERROR_CONDITION_NON_EXISTING_PORT: Non-existing + * port number + * @ETHTOOL_C33_PSE_EXT_SUBSTATE_ERROR_CONDITION_UNDEFINED_PORT: Undefined port + * @ETHTOOL_C33_PSE_EXT_SUBSTATE_ERROR_CONDITION_INTERNAL_HW_FAULT: Internal + * hardware fault + * @ETHTOOL_C33_PSE_EXT_SUBSTATE_ERROR_CONDITION_COMM_ERROR_AFTER_FORCE_ON: + * Communication error after force on + * @ETHTOOL_C33_PSE_EXT_SUBSTATE_ERROR_CONDITION_UNKNOWN_PORT_STATUS: Unknown + * port status + * @ETHTOOL_C33_PSE_EXT_SUBSTATE_ERROR_CONDITION_HOST_CRASH_TURN_OFF: Host + * crash turn off + * @ETHTOOL_C33_PSE_EXT_SUBSTATE_ERROR_CONDITION_HOST_CRASH_FORCE_SHUTDOWN: + * Host crash force shutdown + * @ETHTOOL_C33_PSE_EXT_SUBSTATE_ERROR_CONDITION_CONFIG_CHANGE: Configuration + * change + * @ETHTOOL_C33_PSE_EXT_SUBSTATE_ERROR_CONDITION_DETECTED_OVER_TEMP: Over + * temperature detected + * + * error_condition is a variable indicating the status of + * implementation-specific fault conditions or optionally other system faults + * that prevent the PSE from meeting the specifications in Table 33–11 and that + * require the PSE not to source power. These error conditions are different + * from those monitored by the state diagrams in Figure 33–10. + */ +enum ethtool_c33_pse_ext_substate_error_condition { + ETHTOOL_C33_PSE_EXT_SUBSTATE_ERROR_CONDITION_NON_EXISTING_PORT = 1, + ETHTOOL_C33_PSE_EXT_SUBSTATE_ERROR_CONDITION_UNDEFINED_PORT, + ETHTOOL_C33_PSE_EXT_SUBSTATE_ERROR_CONDITION_INTERNAL_HW_FAULT, + ETHTOOL_C33_PSE_EXT_SUBSTATE_ERROR_CONDITION_COMM_ERROR_AFTER_FORCE_ON, + ETHTOOL_C33_PSE_EXT_SUBSTATE_ERROR_CONDITION_UNKNOWN_PORT_STATUS, + ETHTOOL_C33_PSE_EXT_SUBSTATE_ERROR_CONDITION_HOST_CRASH_TURN_OFF, + ETHTOOL_C33_PSE_EXT_SUBSTATE_ERROR_CONDITION_HOST_CRASH_FORCE_SHUTDOWN, + ETHTOOL_C33_PSE_EXT_SUBSTATE_ERROR_CONDITION_CONFIG_CHANGE, + ETHTOOL_C33_PSE_EXT_SUBSTATE_ERROR_CONDITION_DETECTED_OVER_TEMP, +}; + +/** + * enum ethtool_c33_pse_ext_substate_mr_pse_enable - mr_pse_enable states + * functions. IEEE 802.3-2022 33.2.4.4 Variables + * + * @ETHTOOL_C33_PSE_EXT_SUBSTATE_MR_PSE_ENABLE_DISABLE_PIN_ACTIVE: Disable + * pin active + * + * mr_pse_enable is control variable that selects PSE operation and test + * functions. + */ +enum ethtool_c33_pse_ext_substate_mr_pse_enable { + ETHTOOL_C33_PSE_EXT_SUBSTATE_MR_PSE_ENABLE_DISABLE_PIN_ACTIVE = 1, +}; + +/** + * enum ethtool_c33_pse_ext_substate_option_detect_ted - option_detect_ted + * states functions. IEEE 802.3-2022 33.2.4.4 Variables + * + * @ETHTOOL_C33_PSE_EXT_SUBSTATE_OPTION_DETECT_TED_DET_IN_PROCESS: Detection + * in process + * @ETHTOOL_C33_PSE_EXT_SUBSTATE_OPTION_DETECT_TED_CONNECTION_CHECK_ERROR: + * Connection check error + * + * option_detect_ted is a variable indicating if detection can be performed + * by the PSE during the ted_timer interval. + */ +enum ethtool_c33_pse_ext_substate_option_detect_ted { + ETHTOOL_C33_PSE_EXT_SUBSTATE_OPTION_DETECT_TED_DET_IN_PROCESS = 1, + ETHTOOL_C33_PSE_EXT_SUBSTATE_OPTION_DETECT_TED_CONNECTION_CHECK_ERROR, +}; + +/** + * enum ethtool_c33_pse_ext_substate_option_vport_lim - option_vport_lim states + * functions. IEEE 802.3-2022 33.2.4.4 Variables + * + * @ETHTOOL_C33_PSE_EXT_SUBSTATE_OPTION_VPORT_LIM_HIGH_VOLTAGE: Main supply + * voltage is high + * @ETHTOOL_C33_PSE_EXT_SUBSTATE_OPTION_VPORT_LIM_LOW_VOLTAGE: Main supply + * voltage is low + * @ETHTOOL_C33_PSE_EXT_SUBSTATE_OPTION_VPORT_LIM_VOLTAGE_INJECTION: Voltage + * injection into the port + * + * option_vport_lim is an optional variable indicates if VPSE is out of the + * operating range during normal operating state. + */ +enum ethtool_c33_pse_ext_substate_option_vport_lim { + ETHTOOL_C33_PSE_EXT_SUBSTATE_OPTION_VPORT_LIM_HIGH_VOLTAGE = 1, + ETHTOOL_C33_PSE_EXT_SUBSTATE_OPTION_VPORT_LIM_LOW_VOLTAGE, + ETHTOOL_C33_PSE_EXT_SUBSTATE_OPTION_VPORT_LIM_VOLTAGE_INJECTION, +}; + +/** + * enum ethtool_c33_pse_ext_substate_ovld_detected - ovld_detected states + * functions. IEEE 802.3-2022 33.2.4.4 Variables + * + * @ETHTOOL_C33_PSE_EXT_SUBSTATE_OVLD_DETECTED_OVERLOAD: Overload state + * + * ovld_detected is a variable indicating if the PSE output current has been + * in an overload condition (see 33.2.7.6) for at least TCUT of a one-second + * sliding time. + */ +enum ethtool_c33_pse_ext_substate_ovld_detected { + ETHTOOL_C33_PSE_EXT_SUBSTATE_OVLD_DETECTED_OVERLOAD = 1, +}; + +/** + * enum ethtool_c33_pse_ext_substate_power_not_available - power_not_available + * states functions. IEEE 802.3-2022 33.2.4.4 Variables + * + * @ETHTOOL_C33_PSE_EXT_SUBSTATE_POWER_NOT_AVAILABLE_BUDGET_EXCEEDED: Power + * budget exceeded for the controller + * @ETHTOOL_C33_PSE_EXT_SUBSTATE_POWER_NOT_AVAILABLE_PORT_PW_LIMIT_EXCEEDS_CONTROLLER_BUDGET: + * Configured port power limit exceeded controller power budget + * @ETHTOOL_C33_PSE_EXT_SUBSTATE_POWER_NOT_AVAILABLE_PD_REQUEST_EXCEEDS_PORT_LIMIT: + * Power request from PD exceeds port limit + * @ETHTOOL_C33_PSE_EXT_SUBSTATE_POWER_NOT_AVAILABLE_HW_PW_LIMIT: Power + * denied due to Hardware power limit + * + * power_not_available is a variable that is asserted in an + * implementation-dependent manner when the PSE is no longer capable of + * sourcing sufficient power to support the attached PD. Sufficient power + * is defined by classification; see 33.2.6. + */ +enum ethtool_c33_pse_ext_substate_power_not_available { + ETHTOOL_C33_PSE_EXT_SUBSTATE_POWER_NOT_AVAILABLE_BUDGET_EXCEEDED = 1, + ETHTOOL_C33_PSE_EXT_SUBSTATE_POWER_NOT_AVAILABLE_PORT_PW_LIMIT_EXCEEDS_CONTROLLER_BUDGET, + ETHTOOL_C33_PSE_EXT_SUBSTATE_POWER_NOT_AVAILABLE_PD_REQUEST_EXCEEDS_PORT_LIMIT, + ETHTOOL_C33_PSE_EXT_SUBSTATE_POWER_NOT_AVAILABLE_HW_PW_LIMIT, +}; + +/** + * enum ethtool_c33_pse_ext_substate_short_detected - short_detected states + * functions. IEEE 802.3-2022 33.2.4.4 Variables + * + * @ETHTOOL_C33_PSE_EXT_SUBSTATE_SHORT_DETECTED_SHORT_CONDITION: Short + * condition was detected + * + * short_detected is a variable indicating if the PSE output current has been + * in a short circuit condition for TLIM within a sliding window (see 33.2.7.7). + */ +enum ethtool_c33_pse_ext_substate_short_detected { + ETHTOOL_C33_PSE_EXT_SUBSTATE_SHORT_DETECTED_SHORT_CONDITION = 1, +}; + +/** + * enum ethtool_pse_types - Types of PSE controller. + * @ETHTOOL_PSE_UNKNOWN: Type of PSE controller is unknown + * @ETHTOOL_PSE_PODL: PSE controller which support PoDL + * @ETHTOOL_PSE_C33: PSE controller which support Clause 33 (PoE) + */ +enum ethtool_pse_types { + ETHTOOL_PSE_UNKNOWN = 1 << 0, + ETHTOOL_PSE_PODL = 1 << 1, + ETHTOOL_PSE_C33 = 1 << 2, +}; + +/** + * enum ethtool_c33_pse_admin_state - operational state of the PoDL PSE + * functions. IEEE 802.3-2022 30.9.1.1.2 aPSEAdminState + * @ETHTOOL_C33_PSE_ADMIN_STATE_UNKNOWN: state of PSE functions is unknown + * @ETHTOOL_C33_PSE_ADMIN_STATE_DISABLED: PSE functions are disabled + * @ETHTOOL_C33_PSE_ADMIN_STATE_ENABLED: PSE functions are enabled + */ +enum ethtool_c33_pse_admin_state { + ETHTOOL_C33_PSE_ADMIN_STATE_UNKNOWN = 1, + ETHTOOL_C33_PSE_ADMIN_STATE_DISABLED, + ETHTOOL_C33_PSE_ADMIN_STATE_ENABLED, +}; + +/** + * enum ethtool_c33_pse_pw_d_status - power detection status of the PSE. + * IEEE 802.3-2022 30.9.1.1.3 aPoDLPSEPowerDetectionStatus: + * @ETHTOOL_C33_PSE_PW_D_STATUS_UNKNOWN: PSE status is unknown + * @ETHTOOL_C33_PSE_PW_D_STATUS_DISABLED: The enumeration "disabled" + * indicates that the PSE State diagram is in the state DISABLED. + * @ETHTOOL_C33_PSE_PW_D_STATUS_SEARCHING: The enumeration "searching" + * indicates the PSE State diagram is in a state other than those + * listed. + * @ETHTOOL_C33_PSE_PW_D_STATUS_DELIVERING: The enumeration + * "deliveringPower" indicates that the PSE State diagram is in the + * state POWER_ON. + * @ETHTOOL_C33_PSE_PW_D_STATUS_TEST: The enumeration "test" indicates that + * the PSE State diagram is in the state TEST_MODE. + * @ETHTOOL_C33_PSE_PW_D_STATUS_FAULT: The enumeration "fault" indicates that + * the PSE State diagram is in the state TEST_ERROR. + * @ETHTOOL_C33_PSE_PW_D_STATUS_OTHERFAULT: The enumeration "otherFault" + * indicates that the PSE State diagram is in the state IDLE due to + * the variable error_condition = true. + */ +enum ethtool_c33_pse_pw_d_status { + ETHTOOL_C33_PSE_PW_D_STATUS_UNKNOWN = 1, + ETHTOOL_C33_PSE_PW_D_STATUS_DISABLED, + ETHTOOL_C33_PSE_PW_D_STATUS_SEARCHING, + ETHTOOL_C33_PSE_PW_D_STATUS_DELIVERING, + ETHTOOL_C33_PSE_PW_D_STATUS_TEST, + ETHTOOL_C33_PSE_PW_D_STATUS_FAULT, + ETHTOOL_C33_PSE_PW_D_STATUS_OTHERFAULT, +}; + +/** + * enum ethtool_podl_pse_admin_state - operational state of the PoDL PSE + * functions. IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState + * @ETHTOOL_PODL_PSE_ADMIN_STATE_UNKNOWN: state of PoDL PSE functions are + * unknown + * @ETHTOOL_PODL_PSE_ADMIN_STATE_DISABLED: PoDL PSE functions are disabled + * @ETHTOOL_PODL_PSE_ADMIN_STATE_ENABLED: PoDL PSE functions are enabled + */ +enum ethtool_podl_pse_admin_state { + ETHTOOL_PODL_PSE_ADMIN_STATE_UNKNOWN = 1, + ETHTOOL_PODL_PSE_ADMIN_STATE_DISABLED, + ETHTOOL_PODL_PSE_ADMIN_STATE_ENABLED, +}; + +/** + * enum ethtool_podl_pse_pw_d_status - power detection status of the PoDL PSE. + * IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus: + * @ETHTOOL_PODL_PSE_PW_D_STATUS_UNKNOWN: PoDL PSE + * @ETHTOOL_PODL_PSE_PW_D_STATUS_DISABLED: "The enumeration “disabled” is + * asserted true when the PoDL PSE state diagram variable mr_pse_enable is + * false" + * @ETHTOOL_PODL_PSE_PW_D_STATUS_SEARCHING: "The enumeration “searching” is + * asserted true when either of the PSE state diagram variables + * pi_detecting or pi_classifying is true." + * @ETHTOOL_PODL_PSE_PW_D_STATUS_DELIVERING: "The enumeration “deliveringPower” + * is asserted true when the PoDL PSE state diagram variable pi_powered is + * true." + * @ETHTOOL_PODL_PSE_PW_D_STATUS_SLEEP: "The enumeration “sleep” is asserted + * true when the PoDL PSE state diagram variable pi_sleeping is true." + * @ETHTOOL_PODL_PSE_PW_D_STATUS_IDLE: "The enumeration “idle” is asserted true + * when the logical combination of the PoDL PSE state diagram variables + * pi_prebiased*!pi_sleeping is true." + * @ETHTOOL_PODL_PSE_PW_D_STATUS_ERROR: "The enumeration “error” is asserted + * true when the PoDL PSE state diagram variable overload_held is true." + */ +enum ethtool_podl_pse_pw_d_status { + ETHTOOL_PODL_PSE_PW_D_STATUS_UNKNOWN = 1, + ETHTOOL_PODL_PSE_PW_D_STATUS_DISABLED, + ETHTOOL_PODL_PSE_PW_D_STATUS_SEARCHING, + ETHTOOL_PODL_PSE_PW_D_STATUS_DELIVERING, + ETHTOOL_PODL_PSE_PW_D_STATUS_SLEEP, + ETHTOOL_PODL_PSE_PW_D_STATUS_IDLE, + ETHTOOL_PODL_PSE_PW_D_STATUS_ERROR, +}; + +/** + * enum ethtool_mm_verify_status - status of MAC Merge Verify function + * @ETHTOOL_MM_VERIFY_STATUS_UNKNOWN: + * verification status is unknown + * @ETHTOOL_MM_VERIFY_STATUS_INITIAL: + * the 802.3 Verify State diagram is in the state INIT_VERIFICATION + * @ETHTOOL_MM_VERIFY_STATUS_VERIFYING: + * the Verify State diagram is in the state VERIFICATION_IDLE, + * SEND_VERIFY or WAIT_FOR_RESPONSE + * @ETHTOOL_MM_VERIFY_STATUS_SUCCEEDED: + * indicates that the Verify State diagram is in the state VERIFIED + * @ETHTOOL_MM_VERIFY_STATUS_FAILED: + * the Verify State diagram is in the state VERIFY_FAIL + * @ETHTOOL_MM_VERIFY_STATUS_DISABLED: + * verification of preemption operation is disabled + */ +enum ethtool_mm_verify_status { + ETHTOOL_MM_VERIFY_STATUS_UNKNOWN, + ETHTOOL_MM_VERIFY_STATUS_INITIAL, + ETHTOOL_MM_VERIFY_STATUS_VERIFYING, + ETHTOOL_MM_VERIFY_STATUS_SUCCEEDED, + ETHTOOL_MM_VERIFY_STATUS_FAILED, + ETHTOOL_MM_VERIFY_STATUS_DISABLED, +}; + +/** + * enum ethtool_module_fw_flash_status - plug-in module firmware flashing status + * @ETHTOOL_MODULE_FW_FLASH_STATUS_STARTED: The firmware flashing process has + * started. + * @ETHTOOL_MODULE_FW_FLASH_STATUS_IN_PROGRESS: The firmware flashing process + * is in progress. + * @ETHTOOL_MODULE_FW_FLASH_STATUS_COMPLETED: The firmware flashing process was + * completed successfully. + * @ETHTOOL_MODULE_FW_FLASH_STATUS_ERROR: The firmware flashing process was + * stopped due to an error. + */ +enum ethtool_module_fw_flash_status { + ETHTOOL_MODULE_FW_FLASH_STATUS_STARTED = 1, + ETHTOOL_MODULE_FW_FLASH_STATUS_IN_PROGRESS, + ETHTOOL_MODULE_FW_FLASH_STATUS_COMPLETED, + ETHTOOL_MODULE_FW_FLASH_STATUS_ERROR, +}; + +/** + * struct ethtool_gstrings - string set for data tagging + * @cmd: Command number = %ETHTOOL_GSTRINGS + * @string_set: String set ID; one of &enum ethtool_stringset + * @len: On return, the number of strings in the string set + * @data: Buffer for strings. Each string is null-padded to a size of + * %ETH_GSTRING_LEN. + * + * Users must use %ETHTOOL_GSSET_INFO to find the number of strings in + * the string set. They must allocate a buffer of the appropriate + * size immediately following this structure. + */ struct ethtool_gstrings { - __u32 cmd; /* ETHTOOL_GSTRINGS */ - __u32 string_set; /* string set id e.c. ETH_SS_TEST, etc*/ - __u32 len; /* number of strings in the string set */ - __u8 data[0]; + __u32 cmd; + __u32 string_set; + __u32 len; + __u8 data[]; }; +/** + * struct ethtool_sset_info - string set information + * @cmd: Command number = %ETHTOOL_GSSET_INFO + * @reserved: Reserved for future use; see the note on reserved space. + * @sset_mask: On entry, a bitmask of string sets to query, with bits + * numbered according to &enum ethtool_stringset. On return, a + * bitmask of those string sets queried that are supported. + * @data: Buffer for string set sizes. On return, this contains the + * size of each string set that was queried and supported, in + * order of ID. + * + * Example: The user passes in @sset_mask = 0x7 (sets 0, 1, 2) and on + * return @sset_mask == 0x6 (sets 1, 2). Then @data[0] contains the + * size of set 1 and @data[1] contains the size of set 2. + * + * Users must allocate a buffer of the appropriate size (4 * number of + * sets queried) immediately following this structure. + */ struct ethtool_sset_info { - __u32 cmd; /* ETHTOOL_GSSET_INFO */ + __u32 cmd; __u32 reserved; - __u64 sset_mask; /* input: each bit selects an sset to query */ - /* output: each bit a returned sset */ - __u32 data[0]; /* ETH_SS_xxx count, in order, based on bits - in sset_mask. One bit implies one - __u32, two bits implies two - __u32's, etc. */ + __u64 sset_mask; + __u32 data[]; }; /** @@ -393,26 +1151,61 @@ enum ethtool_test_flags { ETH_TEST_FL_EXTERNAL_LB_DONE = (1 << 3), }; -/* for requesting NIC test and getting results*/ +/** + * struct ethtool_test - device self-test invocation + * @cmd: Command number = %ETHTOOL_TEST + * @flags: A bitmask of flags from &enum ethtool_test_flags. Some + * flags may be set by the user on entry; others may be set by + * the driver on return. + * @reserved: Reserved for future use; see the note on reserved space. + * @len: On return, the number of test results + * @data: Array of test results + * + * Users must use %ETHTOOL_GSSET_INFO or %ETHTOOL_GDRVINFO to find the + * number of test results that will be returned. They must allocate a + * buffer of the appropriate size (8 * number of results) immediately + * following this structure. + */ struct ethtool_test { - __u32 cmd; /* ETHTOOL_TEST */ - __u32 flags; /* ETH_TEST_FL_xxx */ + __u32 cmd; + __u32 flags; __u32 reserved; - __u32 len; /* result length, in number of u64 elements */ - __u64 data[0]; + __u32 len; + __u64 data[]; }; -/* for dumping NIC-specific statistics */ +/** + * struct ethtool_stats - device-specific statistics + * @cmd: Command number = %ETHTOOL_GSTATS + * @n_stats: On return, the number of statistics + * @data: Array of statistics + * + * Users must use %ETHTOOL_GSSET_INFO or %ETHTOOL_GDRVINFO to find the + * number of statistics that will be returned. They must allocate a + * buffer of the appropriate size (8 * number of statistics) + * immediately following this structure. + */ struct ethtool_stats { - __u32 cmd; /* ETHTOOL_GSTATS */ - __u32 n_stats; /* number of u64's being returned */ - __u64 data[0]; + __u32 cmd; + __u32 n_stats; + __u64 data[]; }; +/** + * struct ethtool_perm_addr - permanent hardware address + * @cmd: Command number = %ETHTOOL_GPERMADDR + * @size: On entry, the size of the buffer. On return, the size of the + * address. The command fails if the buffer is too small. + * @data: Buffer for the address + * + * Users must allocate the buffer immediately following this structure. + * A buffer size of %MAX_ADDR_LEN should be sufficient for any address + * type. + */ struct ethtool_perm_addr { - __u32 cmd; /* ETHTOOL_GPERMADDR */ + __u32 cmd; __u32 size; - __u8 data[0]; + __u8 data[]; }; /* boolean flags controlling per-interface behavior characteristics. @@ -492,6 +1285,56 @@ struct ethtool_usrip4_spec { __u8 proto; }; +/** + * struct ethtool_tcpip6_spec - flow specification for TCP/IPv6 etc. + * @ip6src: Source host + * @ip6dst: Destination host + * @psrc: Source port + * @pdst: Destination port + * @tclass: Traffic Class + * + * This can be used to specify a TCP/IPv6, UDP/IPv6 or SCTP/IPv6 flow. + */ +struct ethtool_tcpip6_spec { + __be32 ip6src[4]; + __be32 ip6dst[4]; + __be16 psrc; + __be16 pdst; + __u8 tclass; +}; + +/** + * struct ethtool_ah_espip6_spec - flow specification for IPsec/IPv6 + * @ip6src: Source host + * @ip6dst: Destination host + * @spi: Security parameters index + * @tclass: Traffic Class + * + * This can be used to specify an IPsec transport or tunnel over IPv6. + */ +struct ethtool_ah_espip6_spec { + __be32 ip6src[4]; + __be32 ip6dst[4]; + __be32 spi; + __u8 tclass; +}; + +/** + * struct ethtool_usrip6_spec - general flow specification for IPv6 + * @ip6src: Source host + * @ip6dst: Destination host + * @l4_4_bytes: First 4 bytes of transport (layer 4) header + * @tclass: Traffic Class + * @l4_proto: Transport protocol number (nexthdr after any Extension Headers) + */ +struct ethtool_usrip6_spec { + __be32 ip6src[4]; + __be32 ip6dst[4]; + __be32 l4_4_bytes; + __u8 tclass; + __u8 l4_proto; +}; + union ethtool_flow_union { struct ethtool_tcpip4_spec tcp_ip4_spec; struct ethtool_tcpip4_spec udp_ip4_spec; @@ -499,6 +1342,12 @@ union ethtool_flow_union { struct ethtool_ah_espip4_spec ah_ip4_spec; struct ethtool_ah_espip4_spec esp_ip4_spec; struct ethtool_usrip4_spec usr_ip4_spec; + struct ethtool_tcpip6_spec tcp_ip6_spec; + struct ethtool_tcpip6_spec udp_ip6_spec; + struct ethtool_tcpip6_spec sctp_ip6_spec; + struct ethtool_ah_espip6_spec ah_ip6_spec; + struct ethtool_ah_espip6_spec esp_ip6_spec; + struct ethtool_usrip6_spec usr_ip6_spec; struct ethhdr ether_spec; __u8 hdata[52]; }; @@ -509,6 +1358,7 @@ union ethtool_flow_union { * @vlan_etype: VLAN EtherType * @vlan_tci: VLAN tag control information * @data: user defined data + * @padding: Reserved for future use; see the note on reserved space. * * Note, @vlan_etype, @vlan_tci, and @data are only valid if %FLOW_EXT * is set in &struct ethtool_rx_flow_spec @flow_type. @@ -533,7 +1383,8 @@ struct ethtool_flow_ext { * includes the %FLOW_EXT or %FLOW_MAC_EXT flag * (see &struct ethtool_flow_ext description). * @ring_cookie: RX ring/queue index to deliver to, or %RX_CLS_FLOW_DISC - * if packets should be discarded + * if packets should be discarded, or %RX_CLS_FLOW_WAKE if the + * packets should be used for Wake-on-LAN with %WAKE_FILTER * @location: Location of rule in the table. Locations must be * numbered such that a flow matching multiple rules will be * classified according to the first (lowest numbered) rule. @@ -548,6 +1399,31 @@ struct ethtool_rx_flow_spec { __u32 location; }; +/* How rings are laid out when accessing virtual functions or + * offloaded queues is device specific. To allow users to do flow + * steering and specify these queues the ring cookie is partitioned + * into a 32bit queue index with an 8 bit virtual function id. + * This also leaves the 3bytes for further specifiers. It is possible + * future devices may support more than 256 virtual functions if + * devices start supporting PCIe w/ARI. However at the moment I + * do not know of any devices that support this so I do not reserve + * space for this at this time. If a future patch consumes the next + * byte it should be aware of this possibility. + */ +#define ETHTOOL_RX_FLOW_SPEC_RING 0x00000000FFFFFFFFLL +#define ETHTOOL_RX_FLOW_SPEC_RING_VF 0x000000FF00000000LL +#define ETHTOOL_RX_FLOW_SPEC_RING_VF_OFF 32 +static inline __u64 ethtool_get_flow_spec_ring(__u64 ring_cookie) +{ + return ETHTOOL_RX_FLOW_SPEC_RING & ring_cookie; +} + +static inline __u64 ethtool_get_flow_spec_ring_vf(__u64 ring_cookie) +{ + return (ETHTOOL_RX_FLOW_SPEC_RING_VF & ring_cookie) >> + ETHTOOL_RX_FLOW_SPEC_RING_VF_OFF; +} + /** * struct ethtool_rxnfc - command to get or set RX flow classification rules * @cmd: Specific command number - %ETHTOOL_GRXFH, %ETHTOOL_SRXFH, @@ -556,12 +1432,15 @@ struct ethtool_rx_flow_spec { * @flow_type: Type of flow to be affected, e.g. %TCP_V4_FLOW * @data: Command-dependent value * @fs: Flow classification rule + * @rss_context: RSS context to be affected * @rule_cnt: Number of rules to be affected * @rule_locs: Array of used rule locations * * For %ETHTOOL_GRXFH and %ETHTOOL_SRXFH, @data is a bitmask indicating * the fields included in the flow hash, e.g. %RXH_IP_SRC. The following - * structure fields must not be used. + * structure fields must not be used, except that if @flow_type includes + * the %FLOW_RSS flag, then @rss_context determines which RSS context to + * act on. * * For %ETHTOOL_GRXRINGS, @data is set to the number of RX rings/queues * on return. @@ -573,7 +1452,9 @@ struct ethtool_rx_flow_spec { * set in @data then special location values should not be used. * * For %ETHTOOL_GRXCLSRULE, @fs.@location specifies the location of an - * existing rule on entry and @fs contains the rule on return. + * existing rule on entry and @fs contains the rule on return; if + * @fs.@flow_type includes the %FLOW_RSS flag, then @rss_context is + * filled with the RSS context ID associated with the rule. * * For %ETHTOOL_GRXCLSRLALL, @rule_cnt specifies the array size of the * user buffer for @rule_locs on entry. On return, @data is the size @@ -584,7 +1465,11 @@ struct ethtool_rx_flow_spec { * For %ETHTOOL_SRXCLSRLINS, @fs specifies the rule to add or update. * @fs.@location either specifies the location to use or is a special * location value with %RX_CLS_LOC_SPECIAL flag set. On return, - * @fs.@location is the actual rule location. + * @fs.@location is the actual rule location. If @fs.@flow_type + * includes the %FLOW_RSS flag, @rss_context is the RSS context ID to + * use for flow spreading traffic which matches this rule. The value + * from the rxfh indirection table will be added to @fs.@ring_cookie + * to choose which ring to deliver to. * * For %ETHTOOL_SRXCLSRLDEL, @fs.@location specifies the location of an * existing rule on entry. @@ -593,7 +1478,7 @@ struct ethtool_rx_flow_spec { * %ETHTOOL_SRXCLSRLINS may add the rule at any suitable unused * location, and may remove a rule at a later location (lower * priority) that matches exactly the same set of flows. The special - * values are: %RX_CLS_LOC_ANY, selecting any location; + * values are %RX_CLS_LOC_ANY, selecting any location; * %RX_CLS_LOC_FIRST, selecting the first suitable location (maximum * priority); and %RX_CLS_LOC_LAST, selecting the last suitable * location (minimum priority). Additional special values may be @@ -605,8 +1490,11 @@ struct ethtool_rxnfc { __u32 flow_type; __u64 data; struct ethtool_rx_flow_spec fs; - __u32 rule_cnt; - __u32 rule_locs[0]; + union { + __u32 rule_cnt; + __u32 rss_context; + }; + __u32 rule_locs[]; }; @@ -626,8 +1514,54 @@ struct ethtool_rxnfc { struct ethtool_rxfh_indir { __u32 cmd; __u32 size; - __u32 ring_index[0]; + __u32 ring_index[]; +}; + +/** + * struct ethtool_rxfh - command to get/set RX flow hash indir or/and hash key. + * @cmd: Specific command number - %ETHTOOL_GRSSH or %ETHTOOL_SRSSH + * @rss_context: RSS context identifier. Context 0 is the default for normal + * traffic; other contexts can be referenced as the destination for RX flow + * classification rules. %ETH_RXFH_CONTEXT_ALLOC is used with command + * %ETHTOOL_SRSSH to allocate a new RSS context; on return this field will + * contain the ID of the newly allocated context. + * @indir_size: On entry, the array size of the user buffer for the + * indirection table, which may be zero, or (for %ETHTOOL_SRSSH), + * %ETH_RXFH_INDIR_NO_CHANGE. On return from %ETHTOOL_GRSSH, + * the array size of the hardware indirection table. + * @key_size: On entry, the array size of the user buffer for the hash key, + * which may be zero. On return from %ETHTOOL_GRSSH, the size of the + * hardware hash key. + * @hfunc: Defines the current RSS hash function used by HW (or to be set to). + * Valid values are one of the %ETH_RSS_HASH_*. + * @input_xfrm: Defines how the input data is transformed. Valid values are one + * of %RXH_XFRM_*. + * @rsvd8: Reserved for future use; see the note on reserved space. + * @rsvd32: Reserved for future use; see the note on reserved space. + * @rss_config: RX ring/queue index for each hash value i.e., indirection table + * of @indir_size __u32 elements, followed by hash key of @key_size + * bytes. + * + * For %ETHTOOL_GRSSH, a @indir_size and key_size of zero means that only the + * size should be returned. For %ETHTOOL_SRSSH, an @indir_size of + * %ETH_RXFH_INDIR_NO_CHANGE means that indir table setting is not requested + * and a @indir_size of zero means the indir table should be reset to default + * values (if @rss_context == 0) or that the RSS context should be deleted. + * An hfunc of zero means that hash function setting is not requested. + */ +struct ethtool_rxfh { + __u32 cmd; + __u32 rss_context; + __u32 indir_size; + __u32 key_size; + __u8 hfunc; + __u8 input_xfrm; + __u8 rsvd8[2]; + __u32 rsvd32; + __u32 rss_config[]; }; +#define ETH_RXFH_CONTEXT_ALLOC 0xffffffff +#define ETH_RXFH_INDIR_NO_CHANGE 0xffffffff /** * struct ethtool_rx_ntuple_flow_spec - specification for RX flow filter @@ -704,17 +1638,16 @@ struct ethtool_flash { * for %ETHTOOL_GET_DUMP_FLAG command * @data: data collected for get dump data operation */ - -#define ETH_FW_DUMP_DISABLE 0 - struct ethtool_dump { __u32 cmd; __u32 version; __u32 flag; __u32 len; - __u8 data[0]; + __u8 data[]; }; +#define ETH_FW_DUMP_DISABLE 0 + /* for returning and changing feature sets */ /** @@ -734,14 +1667,15 @@ struct ethtool_get_features_block { /** * struct ethtool_gfeatures - command to get state of device's features * @cmd: command number = %ETHTOOL_GFEATURES - * @size: in: number of elements in the features[] array; - * out: number of elements in features[] needed to hold all features + * @size: On entry, the number of elements in the features[] array; + * on return, the number of elements in features[] needed to hold + * all features * @features: state of features */ struct ethtool_gfeatures { __u32 cmd; __u32 size; - struct ethtool_get_features_block features[0]; + struct ethtool_get_features_block features[]; }; /** @@ -763,7 +1697,7 @@ struct ethtool_set_features_block { struct ethtool_sfeatures { __u32 cmd; __u32 size; - struct ethtool_set_features_block features[0]; + struct ethtool_set_features_block features[]; }; /** @@ -772,12 +1706,19 @@ struct ethtool_sfeatures { * @so_timestamping: bit mask of the sum of the supported SO_TIMESTAMPING flags * @phc_index: device index of the associated PHC, or -1 if there is none * @tx_types: bit mask of the supported hwtstamp_tx_types enumeration values + * @tx_reserved: Reserved for future use; see the note on reserved space. * @rx_filters: bit mask of the supported hwtstamp_rx_filters enumeration values + * @rx_reserved: Reserved for future use; see the note on reserved space. * * The bits in the 'tx_types' and 'rx_filters' fields correspond to * the 'hwtstamp_tx_types' and 'hwtstamp_rx_filters' enumeration values, * respectively. For example, if the device supports HWTSTAMP_TX_ON, * then (1 << HWTSTAMP_TX_ON) in 'tx_types' will be set. + * + * Drivers should only report the filters they actually support without + * upscaling in the SIOCSHWTSTAMP ioctl. If the SIOCSHWSTAMP request for + * HWTSTAMP_FILTER_V1_SYNC is supported by HWTSTAMP_FILTER_V1_EVENT, then the + * driver should only report HWTSTAMP_FILTER_V1_EVENT in this op. */ struct ethtool_ts_info { __u32 cmd; @@ -824,10 +1765,95 @@ enum ethtool_sfeatures_retval_bits { #define ETHTOOL_F_WISH (1 << ETHTOOL_F_WISH__BIT) #define ETHTOOL_F_COMPAT (1 << ETHTOOL_F_COMPAT__BIT) +#define MAX_NUM_QUEUE 4096 + +/** + * struct ethtool_per_queue_op - apply sub command to the queues in mask. + * @cmd: ETHTOOL_PERQUEUE + * @sub_command: the sub command which apply to each queues + * @queue_mask: Bitmap of the queues which sub command apply to + * @data: A complete command structure following for each of the queues addressed + */ +struct ethtool_per_queue_op { + __u32 cmd; + __u32 sub_command; + __u32 queue_mask[__KERNEL_DIV_ROUND_UP(MAX_NUM_QUEUE, 32)]; + char data[]; +}; + +/** + * struct ethtool_fecparam - Ethernet Forward Error Correction parameters + * @cmd: Command number = %ETHTOOL_GFECPARAM or %ETHTOOL_SFECPARAM + * @active_fec: FEC mode which is active on the port, single bit set, GET only. + * @fec: Bitmask of configured FEC modes. + * @reserved: Reserved for future extensions, ignore on GET, write 0 for SET. + * + * Note that @reserved was never validated on input and ethtool user space + * left it uninitialized when calling SET. Hence going forward it can only be + * used to return a value to userspace with GET. + * + * FEC modes supported by the device can be read via %ETHTOOL_GLINKSETTINGS. + * FEC settings are configured by link autonegotiation whenever it's enabled. + * With autoneg on %ETHTOOL_GFECPARAM can be used to read the current mode. + * + * When autoneg is disabled %ETHTOOL_SFECPARAM controls the FEC settings. + * It is recommended that drivers only accept a single bit set in @fec. + * When multiple bits are set in @fec drivers may pick mode in an implementation + * dependent way. Drivers should reject mixing %ETHTOOL_FEC_AUTO_BIT with other + * FEC modes, because it's unclear whether in this case other modes constrain + * AUTO or are independent choices. + * Drivers must reject SET requests if they support none of the requested modes. + * + * If device does not support FEC drivers may use %ETHTOOL_FEC_NONE instead + * of returning %EOPNOTSUPP from %ETHTOOL_GFECPARAM. + * + * See enum ethtool_fec_config_bits for definition of valid bits for both + * @fec and @active_fec. + */ +struct ethtool_fecparam { + __u32 cmd; + /* bitmask of FEC modes */ + __u32 active_fec; + __u32 fec; + __u32 reserved; +}; + +/** + * enum ethtool_fec_config_bits - flags definition of ethtool_fec_configuration + * @ETHTOOL_FEC_NONE_BIT: FEC mode configuration is not supported. Should not + * be used together with other bits. GET only. + * @ETHTOOL_FEC_AUTO_BIT: Select default/best FEC mode automatically, usually + * based link mode and SFP parameters read from module's + * EEPROM. This bit does _not_ mean autonegotiation. + * @ETHTOOL_FEC_OFF_BIT: No FEC Mode + * @ETHTOOL_FEC_RS_BIT: Reed-Solomon FEC Mode + * @ETHTOOL_FEC_BASER_BIT: Base-R/Reed-Solomon FEC Mode + * @ETHTOOL_FEC_LLRS_BIT: Low Latency Reed Solomon FEC Mode (25G/50G Ethernet + * Consortium) + */ +enum ethtool_fec_config_bits { + ETHTOOL_FEC_NONE_BIT, + ETHTOOL_FEC_AUTO_BIT, + ETHTOOL_FEC_OFF_BIT, + ETHTOOL_FEC_RS_BIT, + ETHTOOL_FEC_BASER_BIT, + ETHTOOL_FEC_LLRS_BIT, +}; + +#define ETHTOOL_FEC_NONE (1 << ETHTOOL_FEC_NONE_BIT) +#define ETHTOOL_FEC_AUTO (1 << ETHTOOL_FEC_AUTO_BIT) +#define ETHTOOL_FEC_OFF (1 << ETHTOOL_FEC_OFF_BIT) +#define ETHTOOL_FEC_RS (1 << ETHTOOL_FEC_RS_BIT) +#define ETHTOOL_FEC_BASER (1 << ETHTOOL_FEC_BASER_BIT) +#define ETHTOOL_FEC_LLRS (1 << ETHTOOL_FEC_LLRS_BIT) /* CMDs currently supported */ -#define ETHTOOL_GSET 0x00000001 /* Get settings. */ -#define ETHTOOL_SSET 0x00000002 /* Set settings. */ +#define ETHTOOL_GSET 0x00000001 /* DEPRECATED, Get settings. + * Please use ETHTOOL_GLINKSETTINGS + */ +#define ETHTOOL_SSET 0x00000002 /* DEPRECATED, Set settings. + * Please use ETHTOOL_SLINKSETTINGS + */ #define ETHTOOL_GDRVINFO 0x00000003 /* Get driver info. */ #define ETHTOOL_GREGS 0x00000004 /* Get NIC registers. */ #define ETHTOOL_GWOL 0x00000005 /* Get wake-on-lan options. */ @@ -901,67 +1927,246 @@ enum ethtool_sfeatures_retval_bits { #define ETHTOOL_GEEE 0x00000044 /* Get EEE settings */ #define ETHTOOL_SEEE 0x00000045 /* Set EEE settings */ +#define ETHTOOL_GRSSH 0x00000046 /* Get RX flow hash configuration */ +#define ETHTOOL_SRSSH 0x00000047 /* Set RX flow hash configuration */ +#define ETHTOOL_GTUNABLE 0x00000048 /* Get tunable configuration */ +#define ETHTOOL_STUNABLE 0x00000049 /* Set tunable configuration */ +#define ETHTOOL_GPHYSTATS 0x0000004a /* get PHY-specific statistics */ + +#define ETHTOOL_PERQUEUE 0x0000004b /* Set per queue options */ + +#define ETHTOOL_GLINKSETTINGS 0x0000004c /* Get ethtool_link_settings */ +#define ETHTOOL_SLINKSETTINGS 0x0000004d /* Set ethtool_link_settings */ +#define ETHTOOL_PHY_GTUNABLE 0x0000004e /* Get PHY tunable configuration */ +#define ETHTOOL_PHY_STUNABLE 0x0000004f /* Set PHY tunable configuration */ +#define ETHTOOL_GFECPARAM 0x00000050 /* Get FEC settings */ +#define ETHTOOL_SFECPARAM 0x00000051 /* Set FEC settings */ + /* compatibility with older code */ #define SPARC_ETH_GSET ETHTOOL_GSET #define SPARC_ETH_SSET ETHTOOL_SSET -/* Indicates what features are supported by the interface. */ -#define SUPPORTED_10baseT_Half (1 << 0) -#define SUPPORTED_10baseT_Full (1 << 1) -#define SUPPORTED_100baseT_Half (1 << 2) -#define SUPPORTED_100baseT_Full (1 << 3) -#define SUPPORTED_1000baseT_Half (1 << 4) -#define SUPPORTED_1000baseT_Full (1 << 5) -#define SUPPORTED_Autoneg (1 << 6) -#define SUPPORTED_TP (1 << 7) -#define SUPPORTED_AUI (1 << 8) -#define SUPPORTED_MII (1 << 9) -#define SUPPORTED_FIBRE (1 << 10) -#define SUPPORTED_BNC (1 << 11) -#define SUPPORTED_10000baseT_Full (1 << 12) -#define SUPPORTED_Pause (1 << 13) -#define SUPPORTED_Asym_Pause (1 << 14) -#define SUPPORTED_2500baseX_Full (1 << 15) -#define SUPPORTED_Backplane (1 << 16) -#define SUPPORTED_1000baseKX_Full (1 << 17) -#define SUPPORTED_10000baseKX4_Full (1 << 18) -#define SUPPORTED_10000baseKR_Full (1 << 19) -#define SUPPORTED_10000baseR_FEC (1 << 20) -#define SUPPORTED_20000baseMLD2_Full (1 << 21) -#define SUPPORTED_20000baseKR2_Full (1 << 22) -#define SUPPORTED_40000baseKR4_Full (1 << 23) -#define SUPPORTED_40000baseCR4_Full (1 << 24) -#define SUPPORTED_40000baseSR4_Full (1 << 25) -#define SUPPORTED_40000baseLR4_Full (1 << 26) - -/* Indicates what features are advertised by the interface. */ -#define ADVERTISED_10baseT_Half (1 << 0) -#define ADVERTISED_10baseT_Full (1 << 1) -#define ADVERTISED_100baseT_Half (1 << 2) -#define ADVERTISED_100baseT_Full (1 << 3) -#define ADVERTISED_1000baseT_Half (1 << 4) -#define ADVERTISED_1000baseT_Full (1 << 5) -#define ADVERTISED_Autoneg (1 << 6) -#define ADVERTISED_TP (1 << 7) -#define ADVERTISED_AUI (1 << 8) -#define ADVERTISED_MII (1 << 9) -#define ADVERTISED_FIBRE (1 << 10) -#define ADVERTISED_BNC (1 << 11) -#define ADVERTISED_10000baseT_Full (1 << 12) -#define ADVERTISED_Pause (1 << 13) -#define ADVERTISED_Asym_Pause (1 << 14) -#define ADVERTISED_2500baseX_Full (1 << 15) -#define ADVERTISED_Backplane (1 << 16) -#define ADVERTISED_1000baseKX_Full (1 << 17) -#define ADVERTISED_10000baseKX4_Full (1 << 18) -#define ADVERTISED_10000baseKR_Full (1 << 19) -#define ADVERTISED_10000baseR_FEC (1 << 20) -#define ADVERTISED_20000baseMLD2_Full (1 << 21) -#define ADVERTISED_20000baseKR2_Full (1 << 22) -#define ADVERTISED_40000baseKR4_Full (1 << 23) -#define ADVERTISED_40000baseCR4_Full (1 << 24) -#define ADVERTISED_40000baseSR4_Full (1 << 25) -#define ADVERTISED_40000baseLR4_Full (1 << 26) +/* Link mode bit indices */ +enum ethtool_link_mode_bit_indices { + ETHTOOL_LINK_MODE_10baseT_Half_BIT = 0, + ETHTOOL_LINK_MODE_10baseT_Full_BIT = 1, + ETHTOOL_LINK_MODE_100baseT_Half_BIT = 2, + ETHTOOL_LINK_MODE_100baseT_Full_BIT = 3, + ETHTOOL_LINK_MODE_1000baseT_Half_BIT = 4, + ETHTOOL_LINK_MODE_1000baseT_Full_BIT = 5, + ETHTOOL_LINK_MODE_Autoneg_BIT = 6, + ETHTOOL_LINK_MODE_TP_BIT = 7, + ETHTOOL_LINK_MODE_AUI_BIT = 8, + ETHTOOL_LINK_MODE_MII_BIT = 9, + ETHTOOL_LINK_MODE_FIBRE_BIT = 10, + ETHTOOL_LINK_MODE_BNC_BIT = 11, + ETHTOOL_LINK_MODE_10000baseT_Full_BIT = 12, + ETHTOOL_LINK_MODE_Pause_BIT = 13, + ETHTOOL_LINK_MODE_Asym_Pause_BIT = 14, + ETHTOOL_LINK_MODE_2500baseX_Full_BIT = 15, + ETHTOOL_LINK_MODE_Backplane_BIT = 16, + ETHTOOL_LINK_MODE_1000baseKX_Full_BIT = 17, + ETHTOOL_LINK_MODE_10000baseKX4_Full_BIT = 18, + ETHTOOL_LINK_MODE_10000baseKR_Full_BIT = 19, + ETHTOOL_LINK_MODE_10000baseR_FEC_BIT = 20, + ETHTOOL_LINK_MODE_20000baseMLD2_Full_BIT = 21, + ETHTOOL_LINK_MODE_20000baseKR2_Full_BIT = 22, + ETHTOOL_LINK_MODE_40000baseKR4_Full_BIT = 23, + ETHTOOL_LINK_MODE_40000baseCR4_Full_BIT = 24, + ETHTOOL_LINK_MODE_40000baseSR4_Full_BIT = 25, + ETHTOOL_LINK_MODE_40000baseLR4_Full_BIT = 26, + ETHTOOL_LINK_MODE_56000baseKR4_Full_BIT = 27, + ETHTOOL_LINK_MODE_56000baseCR4_Full_BIT = 28, + ETHTOOL_LINK_MODE_56000baseSR4_Full_BIT = 29, + ETHTOOL_LINK_MODE_56000baseLR4_Full_BIT = 30, + ETHTOOL_LINK_MODE_25000baseCR_Full_BIT = 31, + + /* Last allowed bit for __ETHTOOL_LINK_MODE_LEGACY_MASK is bit + * 31. Please do NOT define any SUPPORTED_* or ADVERTISED_* + * macro for bits > 31. The only way to use indices > 31 is to + * use the new ETHTOOL_GLINKSETTINGS/ETHTOOL_SLINKSETTINGS API. + */ + + ETHTOOL_LINK_MODE_25000baseKR_Full_BIT = 32, + ETHTOOL_LINK_MODE_25000baseSR_Full_BIT = 33, + ETHTOOL_LINK_MODE_50000baseCR2_Full_BIT = 34, + ETHTOOL_LINK_MODE_50000baseKR2_Full_BIT = 35, + ETHTOOL_LINK_MODE_100000baseKR4_Full_BIT = 36, + ETHTOOL_LINK_MODE_100000baseSR4_Full_BIT = 37, + ETHTOOL_LINK_MODE_100000baseCR4_Full_BIT = 38, + ETHTOOL_LINK_MODE_100000baseLR4_ER4_Full_BIT = 39, + ETHTOOL_LINK_MODE_50000baseSR2_Full_BIT = 40, + ETHTOOL_LINK_MODE_1000baseX_Full_BIT = 41, + ETHTOOL_LINK_MODE_10000baseCR_Full_BIT = 42, + ETHTOOL_LINK_MODE_10000baseSR_Full_BIT = 43, + ETHTOOL_LINK_MODE_10000baseLR_Full_BIT = 44, + ETHTOOL_LINK_MODE_10000baseLRM_Full_BIT = 45, + ETHTOOL_LINK_MODE_10000baseER_Full_BIT = 46, + ETHTOOL_LINK_MODE_2500baseT_Full_BIT = 47, + ETHTOOL_LINK_MODE_5000baseT_Full_BIT = 48, + + ETHTOOL_LINK_MODE_FEC_NONE_BIT = 49, + ETHTOOL_LINK_MODE_FEC_RS_BIT = 50, + ETHTOOL_LINK_MODE_FEC_BASER_BIT = 51, + ETHTOOL_LINK_MODE_50000baseKR_Full_BIT = 52, + ETHTOOL_LINK_MODE_50000baseSR_Full_BIT = 53, + ETHTOOL_LINK_MODE_50000baseCR_Full_BIT = 54, + ETHTOOL_LINK_MODE_50000baseLR_ER_FR_Full_BIT = 55, + ETHTOOL_LINK_MODE_50000baseDR_Full_BIT = 56, + ETHTOOL_LINK_MODE_100000baseKR2_Full_BIT = 57, + ETHTOOL_LINK_MODE_100000baseSR2_Full_BIT = 58, + ETHTOOL_LINK_MODE_100000baseCR2_Full_BIT = 59, + ETHTOOL_LINK_MODE_100000baseLR2_ER2_FR2_Full_BIT = 60, + ETHTOOL_LINK_MODE_100000baseDR2_Full_BIT = 61, + ETHTOOL_LINK_MODE_200000baseKR4_Full_BIT = 62, + ETHTOOL_LINK_MODE_200000baseSR4_Full_BIT = 63, + ETHTOOL_LINK_MODE_200000baseLR4_ER4_FR4_Full_BIT = 64, + ETHTOOL_LINK_MODE_200000baseDR4_Full_BIT = 65, + ETHTOOL_LINK_MODE_200000baseCR4_Full_BIT = 66, + ETHTOOL_LINK_MODE_100baseT1_Full_BIT = 67, + ETHTOOL_LINK_MODE_1000baseT1_Full_BIT = 68, + ETHTOOL_LINK_MODE_400000baseKR8_Full_BIT = 69, + ETHTOOL_LINK_MODE_400000baseSR8_Full_BIT = 70, + ETHTOOL_LINK_MODE_400000baseLR8_ER8_FR8_Full_BIT = 71, + ETHTOOL_LINK_MODE_400000baseDR8_Full_BIT = 72, + ETHTOOL_LINK_MODE_400000baseCR8_Full_BIT = 73, + ETHTOOL_LINK_MODE_FEC_LLRS_BIT = 74, + ETHTOOL_LINK_MODE_100000baseKR_Full_BIT = 75, + ETHTOOL_LINK_MODE_100000baseSR_Full_BIT = 76, + ETHTOOL_LINK_MODE_100000baseLR_ER_FR_Full_BIT = 77, + ETHTOOL_LINK_MODE_100000baseCR_Full_BIT = 78, + ETHTOOL_LINK_MODE_100000baseDR_Full_BIT = 79, + ETHTOOL_LINK_MODE_200000baseKR2_Full_BIT = 80, + ETHTOOL_LINK_MODE_200000baseSR2_Full_BIT = 81, + ETHTOOL_LINK_MODE_200000baseLR2_ER2_FR2_Full_BIT = 82, + ETHTOOL_LINK_MODE_200000baseDR2_Full_BIT = 83, + ETHTOOL_LINK_MODE_200000baseCR2_Full_BIT = 84, + ETHTOOL_LINK_MODE_400000baseKR4_Full_BIT = 85, + ETHTOOL_LINK_MODE_400000baseSR4_Full_BIT = 86, + ETHTOOL_LINK_MODE_400000baseLR4_ER4_FR4_Full_BIT = 87, + ETHTOOL_LINK_MODE_400000baseDR4_Full_BIT = 88, + ETHTOOL_LINK_MODE_400000baseCR4_Full_BIT = 89, + ETHTOOL_LINK_MODE_100baseFX_Half_BIT = 90, + ETHTOOL_LINK_MODE_100baseFX_Full_BIT = 91, + ETHTOOL_LINK_MODE_10baseT1L_Full_BIT = 92, + ETHTOOL_LINK_MODE_800000baseCR8_Full_BIT = 93, + ETHTOOL_LINK_MODE_800000baseKR8_Full_BIT = 94, + ETHTOOL_LINK_MODE_800000baseDR8_Full_BIT = 95, + ETHTOOL_LINK_MODE_800000baseDR8_2_Full_BIT = 96, + ETHTOOL_LINK_MODE_800000baseSR8_Full_BIT = 97, + ETHTOOL_LINK_MODE_800000baseVR8_Full_BIT = 98, + ETHTOOL_LINK_MODE_10baseT1S_Full_BIT = 99, + ETHTOOL_LINK_MODE_10baseT1S_Half_BIT = 100, + ETHTOOL_LINK_MODE_10baseT1S_P2MP_Half_BIT = 101, + ETHTOOL_LINK_MODE_10baseT1BRR_Full_BIT = 102, + ETHTOOL_LINK_MODE_200000baseCR_Full_BIT = 103, + ETHTOOL_LINK_MODE_200000baseKR_Full_BIT = 104, + ETHTOOL_LINK_MODE_200000baseDR_Full_BIT = 105, + ETHTOOL_LINK_MODE_200000baseDR_2_Full_BIT = 106, + ETHTOOL_LINK_MODE_200000baseSR_Full_BIT = 107, + ETHTOOL_LINK_MODE_200000baseVR_Full_BIT = 108, + ETHTOOL_LINK_MODE_400000baseCR2_Full_BIT = 109, + ETHTOOL_LINK_MODE_400000baseKR2_Full_BIT = 110, + ETHTOOL_LINK_MODE_400000baseDR2_Full_BIT = 111, + ETHTOOL_LINK_MODE_400000baseDR2_2_Full_BIT = 112, + ETHTOOL_LINK_MODE_400000baseSR2_Full_BIT = 113, + ETHTOOL_LINK_MODE_400000baseVR2_Full_BIT = 114, + ETHTOOL_LINK_MODE_800000baseCR4_Full_BIT = 115, + ETHTOOL_LINK_MODE_800000baseKR4_Full_BIT = 116, + ETHTOOL_LINK_MODE_800000baseDR4_Full_BIT = 117, + ETHTOOL_LINK_MODE_800000baseDR4_2_Full_BIT = 118, + ETHTOOL_LINK_MODE_800000baseSR4_Full_BIT = 119, + ETHTOOL_LINK_MODE_800000baseVR4_Full_BIT = 120, + ETHTOOL_LINK_MODE_1600000baseCR8_Full_BIT = 121, + ETHTOOL_LINK_MODE_1600000baseKR8_Full_BIT = 122, + ETHTOOL_LINK_MODE_1600000baseDR8_Full_BIT = 123, + ETHTOOL_LINK_MODE_1600000baseDR8_2_Full_BIT = 124, + + /* must be last entry */ + __ETHTOOL_LINK_MODE_MASK_NBITS +}; + +#define __ETHTOOL_LINK_MODE_LEGACY_MASK(base_name) \ + (1UL << (ETHTOOL_LINK_MODE_ ## base_name ## _BIT)) + +/* DEPRECATED macros. Please migrate to + * ETHTOOL_GLINKSETTINGS/ETHTOOL_SLINKSETTINGS API. Please do NOT + * define any new SUPPORTED_* macro for bits > 31. + */ +#define SUPPORTED_10baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(10baseT_Half) +#define SUPPORTED_10baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10baseT_Full) +#define SUPPORTED_100baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(100baseT_Half) +#define SUPPORTED_100baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(100baseT_Full) +#define SUPPORTED_1000baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseT_Half) +#define SUPPORTED_1000baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseT_Full) +#define SUPPORTED_Autoneg __ETHTOOL_LINK_MODE_LEGACY_MASK(Autoneg) +#define SUPPORTED_TP __ETHTOOL_LINK_MODE_LEGACY_MASK(TP) +#define SUPPORTED_AUI __ETHTOOL_LINK_MODE_LEGACY_MASK(AUI) +#define SUPPORTED_MII __ETHTOOL_LINK_MODE_LEGACY_MASK(MII) +#define SUPPORTED_FIBRE __ETHTOOL_LINK_MODE_LEGACY_MASK(FIBRE) +#define SUPPORTED_BNC __ETHTOOL_LINK_MODE_LEGACY_MASK(BNC) +#define SUPPORTED_10000baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseT_Full) +#define SUPPORTED_Pause __ETHTOOL_LINK_MODE_LEGACY_MASK(Pause) +#define SUPPORTED_Asym_Pause __ETHTOOL_LINK_MODE_LEGACY_MASK(Asym_Pause) +#define SUPPORTED_2500baseX_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(2500baseX_Full) +#define SUPPORTED_Backplane __ETHTOOL_LINK_MODE_LEGACY_MASK(Backplane) +#define SUPPORTED_1000baseKX_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseKX_Full) +#define SUPPORTED_10000baseKX4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseKX4_Full) +#define SUPPORTED_10000baseKR_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseKR_Full) +#define SUPPORTED_10000baseR_FEC __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseR_FEC) +#define SUPPORTED_20000baseMLD2_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(20000baseMLD2_Full) +#define SUPPORTED_20000baseKR2_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(20000baseKR2_Full) +#define SUPPORTED_40000baseKR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseKR4_Full) +#define SUPPORTED_40000baseCR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseCR4_Full) +#define SUPPORTED_40000baseSR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseSR4_Full) +#define SUPPORTED_40000baseLR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseLR4_Full) +#define SUPPORTED_56000baseKR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseKR4_Full) +#define SUPPORTED_56000baseCR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseCR4_Full) +#define SUPPORTED_56000baseSR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseSR4_Full) +#define SUPPORTED_56000baseLR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseLR4_Full) +/* Please do not define any new SUPPORTED_* macro for bits > 31, see + * notice above. + */ + +/* + * DEPRECATED macros. Please migrate to + * ETHTOOL_GLINKSETTINGS/ETHTOOL_SLINKSETTINGS API. Please do NOT + * define any new ADERTISE_* macro for bits > 31. + */ +#define ADVERTISED_10baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(10baseT_Half) +#define ADVERTISED_10baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10baseT_Full) +#define ADVERTISED_100baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(100baseT_Half) +#define ADVERTISED_100baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(100baseT_Full) +#define ADVERTISED_1000baseT_Half __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseT_Half) +#define ADVERTISED_1000baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseT_Full) +#define ADVERTISED_Autoneg __ETHTOOL_LINK_MODE_LEGACY_MASK(Autoneg) +#define ADVERTISED_TP __ETHTOOL_LINK_MODE_LEGACY_MASK(TP) +#define ADVERTISED_AUI __ETHTOOL_LINK_MODE_LEGACY_MASK(AUI) +#define ADVERTISED_MII __ETHTOOL_LINK_MODE_LEGACY_MASK(MII) +#define ADVERTISED_FIBRE __ETHTOOL_LINK_MODE_LEGACY_MASK(FIBRE) +#define ADVERTISED_BNC __ETHTOOL_LINK_MODE_LEGACY_MASK(BNC) +#define ADVERTISED_10000baseT_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseT_Full) +#define ADVERTISED_Pause __ETHTOOL_LINK_MODE_LEGACY_MASK(Pause) +#define ADVERTISED_Asym_Pause __ETHTOOL_LINK_MODE_LEGACY_MASK(Asym_Pause) +#define ADVERTISED_2500baseX_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(2500baseX_Full) +#define ADVERTISED_Backplane __ETHTOOL_LINK_MODE_LEGACY_MASK(Backplane) +#define ADVERTISED_1000baseKX_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(1000baseKX_Full) +#define ADVERTISED_10000baseKX4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseKX4_Full) +#define ADVERTISED_10000baseKR_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseKR_Full) +#define ADVERTISED_10000baseR_FEC __ETHTOOL_LINK_MODE_LEGACY_MASK(10000baseR_FEC) +#define ADVERTISED_20000baseMLD2_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(20000baseMLD2_Full) +#define ADVERTISED_20000baseKR2_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(20000baseKR2_Full) +#define ADVERTISED_40000baseKR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseKR4_Full) +#define ADVERTISED_40000baseCR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseCR4_Full) +#define ADVERTISED_40000baseSR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseSR4_Full) +#define ADVERTISED_40000baseLR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(40000baseLR4_Full) +#define ADVERTISED_56000baseKR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseKR4_Full) +#define ADVERTISED_56000baseCR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseCR4_Full) +#define ADVERTISED_56000baseSR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseSR4_Full) +#define ADVERTISED_56000baseLR4_Full __ETHTOOL_LINK_MODE_LEGACY_MASK(56000baseLR4_Full) +/* Please do not define any new ADVERTISED_* macro for bits > 31, see + * notice above. + */ /* The following are all involved in forcing a particular link * mode for the device for setting things. When getting the @@ -969,19 +2174,78 @@ enum ethtool_sfeatures_retval_bits { * it was forced up into this mode or autonegotiated. */ -/* The forced speed, 10Mb, 100Mb, gigabit, 2.5Gb, 10GbE. */ +/* The forced speed, in units of 1Mb. All values 0 to INT_MAX are legal. + * Update drivers/net/phy/phy.c:phy_speed_to_str() and + * drivers/net/bonding/bond_3ad.c:__get_link_speed() when adding new values. + */ #define SPEED_10 10 #define SPEED_100 100 #define SPEED_1000 1000 #define SPEED_2500 2500 +#define SPEED_5000 5000 #define SPEED_10000 10000 +#define SPEED_14000 14000 +#define SPEED_20000 20000 +#define SPEED_25000 25000 +#define SPEED_40000 40000 +#define SPEED_50000 50000 +#define SPEED_56000 56000 +#define SPEED_100000 100000 +#define SPEED_200000 200000 +#define SPEED_400000 400000 +#define SPEED_800000 800000 +#define SPEED_1600000 1600000 + #define SPEED_UNKNOWN -1 +static inline int ethtool_validate_speed(__u32 speed) +{ + return speed <= INT_MAX || speed == (__u32)SPEED_UNKNOWN; +} + /* Duplex, half or full. */ #define DUPLEX_HALF 0x00 #define DUPLEX_FULL 0x01 #define DUPLEX_UNKNOWN 0xff +static inline int ethtool_validate_duplex(__u8 duplex) +{ + switch (duplex) { + case DUPLEX_HALF: + case DUPLEX_FULL: + case DUPLEX_UNKNOWN: + return 1; + } + + return 0; +} + +#define MASTER_SLAVE_CFG_UNSUPPORTED 0 +#define MASTER_SLAVE_CFG_UNKNOWN 1 +#define MASTER_SLAVE_CFG_MASTER_PREFERRED 2 +#define MASTER_SLAVE_CFG_SLAVE_PREFERRED 3 +#define MASTER_SLAVE_CFG_MASTER_FORCE 4 +#define MASTER_SLAVE_CFG_SLAVE_FORCE 5 +#define MASTER_SLAVE_STATE_UNSUPPORTED 0 +#define MASTER_SLAVE_STATE_UNKNOWN 1 +#define MASTER_SLAVE_STATE_MASTER 2 +#define MASTER_SLAVE_STATE_SLAVE 3 +#define MASTER_SLAVE_STATE_ERR 4 + +/* These are used to throttle the rate of data on the phy interface when the + * native speed of the interface is higher than the link speed. These should + * not be used for phy interfaces which natively support multiple speeds (e.g. + * MII or SGMII). + */ +/* No rate matching performed. */ +#define RATE_MATCH_NONE 0 +/* The phy sends pause frames to throttle the MAC. */ +#define RATE_MATCH_PAUSE 1 +/* The phy asserts CRS to prevent the MAC from transmitting. */ +#define RATE_MATCH_CRS 2 +/* The MAC is programmed with a sufficiently-large IPG. */ +#define RATE_MATCH_OPEN_LOOP 3 + /* Which connector port. */ #define PORT_TP 0x00 #define PORT_AUI 0x01 @@ -999,9 +2263,7 @@ enum ethtool_sfeatures_retval_bits { #define XCVR_DUMMY2 0x03 #define XCVR_DUMMY3 0x04 -/* Enable or disable autonegotiation. If this is set to enable, - * the forced link modes above are completely ignored. - */ +/* Enable or disable autonegotiation. */ #define AUTONEG_DISABLE 0x00 #define AUTONEG_ENABLE 0x01 @@ -1021,29 +2283,100 @@ enum ethtool_sfeatures_retval_bits { #define WAKE_ARP (1 << 4) #define WAKE_MAGIC (1 << 5) #define WAKE_MAGICSECURE (1 << 6) /* only meaningful if WAKE_MAGIC */ +#define WAKE_FILTER (1 << 7) + +#define WOL_MODE_COUNT 8 + +/* RSS hash function data + * XOR the corresponding source and destination fields of each specified + * protocol. Both copies of the XOR'ed fields are fed into the RSS and RXHASH + * calculation. Note that this XORing reduces the input set entropy and could + * be exploited to reduce the RSS queue spread. + */ +#define RXH_XFRM_SYM_XOR (1 << 0) +/* Similar to SYM_XOR, except that one copy of the XOR'ed fields is replaced by + * an OR of the same fields + */ +#define RXH_XFRM_SYM_OR_XOR (1 << 1) +#define RXH_XFRM_NO_CHANGE 0xff + +enum { + /* L2-L4 network traffic flow types */ + TCP_V4_FLOW = 0x01, /* hash or spec (tcp_ip4_spec) */ + UDP_V4_FLOW = 0x02, /* hash or spec (udp_ip4_spec) */ + SCTP_V4_FLOW = 0x03, /* hash or spec (sctp_ip4_spec) */ + AH_ESP_V4_FLOW = 0x04, /* hash only */ + TCP_V6_FLOW = 0x05, /* hash or spec (tcp_ip6_spec; nfc only) */ + UDP_V6_FLOW = 0x06, /* hash or spec (udp_ip6_spec; nfc only) */ + SCTP_V6_FLOW = 0x07, /* hash or spec (sctp_ip6_spec; nfc only) */ + AH_ESP_V6_FLOW = 0x08, /* hash only */ + AH_V4_FLOW = 0x09, /* hash or spec (ah_ip4_spec) */ + ESP_V4_FLOW = 0x0a, /* hash or spec (esp_ip4_spec) */ + AH_V6_FLOW = 0x0b, /* hash or spec (ah_ip6_spec; nfc only) */ + ESP_V6_FLOW = 0x0c, /* hash or spec (esp_ip6_spec; nfc only) */ + IPV4_USER_FLOW = 0x0d, /* spec only (usr_ip4_spec) */ + IP_USER_FLOW = IPV4_USER_FLOW, + IPV6_USER_FLOW = 0x0e, /* spec only (usr_ip6_spec; nfc only) */ + IPV4_FLOW = 0x10, /* hash only */ + IPV6_FLOW = 0x11, /* hash only */ + ETHER_FLOW = 0x12, /* hash or spec (ether_spec) */ + + /* Used for GTP-U IPv4 and IPv6. + * The format of GTP packets only includes + * elements such as TEID and GTP version. + * It is primarily intended for data communication of the UE. + */ + GTPU_V4_FLOW = 0x13, /* hash only */ + GTPU_V6_FLOW = 0x14, /* hash only */ + + /* Use for GTP-C IPv4 and v6. + * The format of these GTP packets does not include TEID. + * Primarily expected to be used for communication + * to create sessions for UE data communication, + * commonly referred to as CSR (Create Session Request). + */ + GTPC_V4_FLOW = 0x15, /* hash only */ + GTPC_V6_FLOW = 0x16, /* hash only */ + + /* Use for GTP-C IPv4 and v6. + * Unlike GTPC_V4_FLOW, the format of these GTP packets includes TEID. + * After session creation, it becomes this packet. + * This is mainly used for requests to realize UE handover. + */ + GTPC_TEID_V4_FLOW = 0x17, /* hash only */ + GTPC_TEID_V6_FLOW = 0x18, /* hash only */ + + /* Use for GTP-U and extended headers for the PSC (PDU Session Container). + * The format of these GTP packets includes TEID and QFI. + * In 5G communication using UPF (User Plane Function), + * data communication with this extended header is performed. + */ + GTPU_EH_V4_FLOW = 0x19, /* hash only */ + GTPU_EH_V6_FLOW = 0x1a, /* hash only */ + + /* Use for GTP-U IPv4 and v6 PSC (PDU Session Container) extended headers. + * This differs from GTPU_EH_V(4|6)_FLOW in that it is distinguished by + * UL/DL included in the PSC. + * There are differences in the data included based on Downlink/Uplink, + * and can be used to distinguish packets. + * The functions described so far are useful when you want to + * handle communication from the mobile network in UPF, PGW, etc. + */ + GTPU_UL_V4_FLOW = 0x1b, /* hash only */ + GTPU_UL_V6_FLOW = 0x1c, /* hash only */ + GTPU_DL_V4_FLOW = 0x1d, /* hash only */ + GTPU_DL_V6_FLOW = 0x1e, /* hash only */ + + __FLOW_TYPE_COUNT, +}; -/* L2-L4 network traffic flow types */ -#define TCP_V4_FLOW 0x01 /* hash or spec (tcp_ip4_spec) */ -#define UDP_V4_FLOW 0x02 /* hash or spec (udp_ip4_spec) */ -#define SCTP_V4_FLOW 0x03 /* hash or spec (sctp_ip4_spec) */ -#define AH_ESP_V4_FLOW 0x04 /* hash only */ -#define TCP_V6_FLOW 0x05 /* hash only */ -#define UDP_V6_FLOW 0x06 /* hash only */ -#define SCTP_V6_FLOW 0x07 /* hash only */ -#define AH_ESP_V6_FLOW 0x08 /* hash only */ -#define AH_V4_FLOW 0x09 /* hash or spec (ah_ip4_spec) */ -#define ESP_V4_FLOW 0x0a /* hash or spec (esp_ip4_spec) */ -#define AH_V6_FLOW 0x0b /* hash only */ -#define ESP_V6_FLOW 0x0c /* hash only */ -#define IP_USER_FLOW 0x0d /* spec only (usr_ip4_spec) */ -#define IPV4_FLOW 0x10 /* hash only */ -#define IPV6_FLOW 0x11 /* hash only */ -#define ETHER_FLOW 0x12 /* spec only (ether_spec) */ /* Flag to enable additional fields in struct ethtool_rx_flow_spec */ #define FLOW_EXT 0x80000000 #define FLOW_MAC_EXT 0x40000000 +/* Flag to enable RSS spreading of traffic matching rule (nfc only) */ +#define FLOW_RSS 0x20000000 -/* L3-L4 network traffic flow hash options */ +/* L2-L4 network traffic flow hash options */ #define RXH_L2DA (1 << 1) #define RXH_VLAN (1 << 2) #define RXH_L3_PROTO (1 << 3) @@ -1051,9 +2384,12 @@ enum ethtool_sfeatures_retval_bits { #define RXH_IP_DST (1 << 5) #define RXH_L4_B_0_1 (1 << 6) /* src port in case of TCP/UDP/SCTP */ #define RXH_L4_B_2_3 (1 << 7) /* dst port in case of TCP/UDP/SCTP */ +#define RXH_GTP_TEID (1 << 8) /* teid in case of GTP */ +#define RXH_IP6_FL (1 << 9) /* IPv6 flow label */ #define RXH_DISCARD (1 << 31) #define RX_CLS_FLOW_DISC 0xffffffffffffffffULL +#define RX_CLS_FLOW_WAKE 0xfffffffffffffffeULL /* Special RX classification rule insert location values */ #define RX_CLS_LOC_SPECIAL 0x80000000 /* flag */ @@ -1066,6 +2402,13 @@ enum ethtool_sfeatures_retval_bits { #define ETH_MODULE_SFF_8079_LEN 256 #define ETH_MODULE_SFF_8472 0x2 #define ETH_MODULE_SFF_8472_LEN 512 +#define ETH_MODULE_SFF_8636 0x3 +#define ETH_MODULE_SFF_8636_LEN 256 +#define ETH_MODULE_SFF_8436 0x4 +#define ETH_MODULE_SFF_8436_LEN 256 + +#define ETH_MODULE_SFF_8636_MAX_LEN 640 +#define ETH_MODULE_SFF_8436_MAX_LEN 640 /* Reset flags */ /* The reset() operation must clear the flags for the components which @@ -1089,6 +2432,7 @@ enum ethtool_reset_flags { ETH_RESET_PHY = 1 << 6, /* Transceiver/PHY */ ETH_RESET_RAM = 1 << 7, /* RAM shared between * multiple components */ + ETH_RESET_AP = 1 << 8, /* Application processor */ ETH_RESET_DEDICATED = 0x0000ffff, /* All components dedicated to * this interface */ @@ -1097,4 +2441,155 @@ enum ethtool_reset_flags { }; #define ETH_RESET_SHARED_SHIFT 16 + +/** + * struct ethtool_link_settings - link control and status + * + * IMPORTANT, Backward compatibility notice: When implementing new + * user-space tools, please first try %ETHTOOL_GLINKSETTINGS, and + * if it succeeds use %ETHTOOL_SLINKSETTINGS to change link + * settings; do not use %ETHTOOL_SSET if %ETHTOOL_GLINKSETTINGS + * succeeded: stick to %ETHTOOL_GLINKSETTINGS/%SLINKSETTINGS in + * that case. Conversely, if %ETHTOOL_GLINKSETTINGS fails, use + * %ETHTOOL_GSET to query and %ETHTOOL_SSET to change link + * settings; do not use %ETHTOOL_SLINKSETTINGS if + * %ETHTOOL_GLINKSETTINGS failed: stick to + * %ETHTOOL_GSET/%ETHTOOL_SSET in that case. + * + * @cmd: Command number = %ETHTOOL_GLINKSETTINGS or %ETHTOOL_SLINKSETTINGS + * @speed: Link speed (Mbps) + * @duplex: Duplex mode; one of %DUPLEX_* + * @port: Physical connector type; one of %PORT_* + * @phy_address: MDIO address of PHY (transceiver); 0 or 255 if not + * applicable. For clause 45 PHYs this is the PRTAD. + * @autoneg: Enable/disable autonegotiation and auto-detection; + * either %AUTONEG_DISABLE or %AUTONEG_ENABLE + * @mdio_support: Bitmask of %ETH_MDIO_SUPPORTS_* flags for the MDIO + * protocols supported by the interface; 0 if unknown. + * Read-only. + * @eth_tp_mdix: Ethernet twisted-pair MDI(-X) status; one of + * %ETH_TP_MDI_*. If the status is unknown or not applicable, the + * value will be %ETH_TP_MDI_INVALID. Read-only. + * @eth_tp_mdix_ctrl: Ethernet twisted pair MDI(-X) control; one of + * %ETH_TP_MDI_*. If MDI(-X) control is not implemented, reads + * yield %ETH_TP_MDI_INVALID and writes may be ignored or rejected. + * When written successfully, the link should be renegotiated if + * necessary. + * @link_mode_masks_nwords: Number of 32-bit words for each of the + * supported, advertising, lp_advertising link mode bitmaps. For + * %ETHTOOL_GLINKSETTINGS: on entry, number of words passed by user + * (>= 0); on return, if handshake in progress, negative if + * request size unsupported by kernel: absolute value indicates + * kernel expected size and all the other fields but cmd + * are 0; otherwise (handshake completed), strictly positive + * to indicate size used by kernel and cmd field stays + * %ETHTOOL_GLINKSETTINGS, all other fields populated by driver. For + * %ETHTOOL_SLINKSETTINGS: must be valid on entry, ie. a positive + * value returned previously by %ETHTOOL_GLINKSETTINGS, otherwise + * refused. For drivers: ignore this field (use kernel's + * __ETHTOOL_LINK_MODE_MASK_NBITS instead), any change to it will + * be overwritten by kernel. + * @transceiver: Used to distinguish different possible PHY types, + * reported consistently by PHYLIB. Read-only. + * @master_slave_cfg: Master/slave port mode. + * @master_slave_state: Master/slave port state. + * @rate_matching: Rate adaptation performed by the PHY + * @reserved: Reserved for future use; see the note on reserved space. + * @link_mode_masks: Variable length bitmaps. + * + * If autonegotiation is disabled, the speed and @duplex represent the + * fixed link mode and are writable if the driver supports multiple + * link modes. If it is enabled then they are read-only; if the link + * is up they represent the negotiated link mode; if the link is down, + * the speed is 0, %SPEED_UNKNOWN or the highest enabled speed and + * @duplex is %DUPLEX_UNKNOWN or the best enabled duplex mode. + * + * Some hardware interfaces may have multiple PHYs and/or physical + * connectors fitted or do not allow the driver to detect which are + * fitted. For these interfaces @port and/or @phy_address may be + * writable, possibly dependent on @autoneg being %AUTONEG_DISABLE. + * Otherwise, attempts to write different values may be ignored or + * rejected. + * + * Deprecated %ethtool_cmd fields transceiver, maxtxpkt and maxrxpkt + * are not available in %ethtool_link_settings. These fields will be + * always set to zero in %ETHTOOL_GSET reply and %ETHTOOL_SSET will + * fail if any of them is set to non-zero value. + * + * Users should assume that all fields not marked read-only are + * writable and subject to validation by the driver. They should use + * %ETHTOOL_GLINKSETTINGS to get the current values before making specific + * changes and then applying them with %ETHTOOL_SLINKSETTINGS. + * + * Drivers that implement %get_link_ksettings and/or + * %set_link_ksettings should ignore the @cmd + * and @link_mode_masks_nwords fields (any change to them overwritten + * by kernel), and rely only on kernel's internal + * %__ETHTOOL_LINK_MODE_MASK_NBITS and + * %ethtool_link_mode_mask_t. Drivers that implement + * %set_link_ksettings() should validate all fields other than @cmd + * and @link_mode_masks_nwords that are not described as read-only or + * deprecated, and must ignore all fields described as read-only. + * + * @link_mode_masks is divided into three bitfields, each of length + * @link_mode_masks_nwords: + * - supported: Bitmap with each bit meaning given by + * %ethtool_link_mode_bit_indices for the link modes, physical + * connectors and other link features for which the interface + * supports autonegotiation or auto-detection. Read-only. + * - advertising: Bitmap with each bit meaning given by + * %ethtool_link_mode_bit_indices for the link modes, physical + * connectors and other link features that are advertised through + * autonegotiation or enabled for auto-detection. + * - lp_advertising: Bitmap with each bit meaning given by + * %ethtool_link_mode_bit_indices for the link modes, and other + * link features that the link partner advertised through + * autonegotiation; 0 if unknown or not applicable. Read-only. + */ +struct ethtool_link_settings { + __u32 cmd; + __u32 speed; + __u8 duplex; + __u8 port; + __u8 phy_address; + __u8 autoneg; + __u8 mdio_support; + __u8 eth_tp_mdix; + __u8 eth_tp_mdix_ctrl; + __s8 link_mode_masks_nwords; + __u8 transceiver; + __u8 master_slave_cfg; + __u8 master_slave_state; + __u8 rate_matching; + __u32 reserved[7]; +#ifndef __KERNEL__ + /* Linux builds with -Wflex-array-member-not-at-end but does + * not use the "link_mode_masks" member. Leave it defined for + * userspace for now, and when userspace wants to start using + * -Wfamnae, we'll need a new solution. + */ + __u32 link_mode_masks[]; + /* layout of link_mode_masks fields: + * __u32 map_supported[link_mode_masks_nwords]; + * __u32 map_advertising[link_mode_masks_nwords]; + * __u32 map_lp_advertising[link_mode_masks_nwords]; + */ +#endif +}; + +/** + * enum phy_upstream - Represents the upstream component a given PHY device + * is connected to, as in what is on the other end of the MII bus. Most PHYs + * will be attached to an Ethernet MAC controller, but in some cases, there's + * an intermediate PHY used as a media-converter, which will driver another + * MII interface as its output. + * @PHY_UPSTREAM_MAC: Upstream component is a MAC (a switch port, + * or ethernet controller) + * @PHY_UPSTREAM_PHY: Upstream component is a PHY (likely a media converter) + */ +enum phy_upstream { + PHY_UPSTREAM_MAC, + PHY_UPSTREAM_PHY, +}; + #endif /* _UAPI_LINUX_ETHTOOL_H */ |