| Age | Commit message (Collapse) | Author |
|---|
|
Normally we could be in a deep PkgC state all the way up to the
point when DSB starts its execution at the transcoders undelayed
vblank. The DSB will then have to wait for the hardware to
wake up before it can execute anything. This will waste a huge
chunk of the vblank time just waiting, and risks the DSB execution
spilling into the vertical active period. That will be very bad,
especially when programming the LUTs as the anti-collision logic
will cause DSB to corrupt LUT writes during vertical active.
To avoid these problems we can instruct the DSB to pre-wake the
display engine on a specific scanline so that everything will
be 100% ready to go when we hit the transcoder's undelayed vblank.
One annoyance is that the scanline is specified as just that,
a single scanline. So if we happen to start the DSB execution
after passing said scanline no DEwake will happen and we may drop
back into some PkgC state before reaching the transcoder's undelayed
vblank. To prevent that we'll use the "force DEwake" bit to manually
force the display engine to stay awake. We'll then have to clear
the force bit again after the DSB is done (the force bit remains
effective even when the DSB is otherwise disabled).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606191504.18099-18-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
|
|
Add a helper to convert our idea of a scanline to the hw's idea
of the same scanline (ie. apply crtc->scanline_offset in reverse).
We'll need this to tell the DSB do stuff on a specific scanline.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606191504.18099-17-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
|
|
The DSB code will want to know the maximum PkgC latency
it has to contend with. Add a helper to expose that
information.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606191504.18099-16-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
|
|
We want to start the DSB execution from the transcoder's undelayed
vblank, so in order to guarantee atomicity with the all the other
mmio register writes we need to evade both vblanks.
Note that currently we don't add any vblank delay, so this is
effectively a nop. But in the future when we start to program
double buffered registers from the DSB we'll need to delay the
pipe's vblank to provide the register programming "window2"
for the DSB.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606191504.18099-15-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
|
|
The DSB has problems writing the legacy LUT. The two workarounds
I've discoverted are:
- write each entry twice back to back
- use non-posted writes
Let's use non-posted writes as that seems a bit more standard.
TODO: measure which is faster
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606191504.18099-14-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
|
|
Loading LUTs with the DSB outside of vblank doesn't really
work due to the palette anti-collision logic. Apparently the
DSB register writes don't get stalled like CPU mmio writes
do and instead we end up corrupting the LUT entries. Disabling
the anti-collision logic would allow us to successfully load
the LUT outside of vblank, but presumably that risks the LUT
reads from the scanout (temporarily) getting corrupted data
from the LUT instead.
The anti-collision logic isn't active during vblank so that
is when we can successfully load the LUT with the DSB. That is
what we want to do anyway to avoid tearing.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606191504.18099-13-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
|
|
Using the DSB for LUT loading during full modesets would require
some actual though. Let's just use mmio for the time being.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606191504.18099-12-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
|
|
Writing specific transcoder registers (and as it turns out, the
legacy LUT as well) via DSB needs a magic sequence to emit
non-posted register writes. Add a helper for this.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606191504.18099-11-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
|
|
Add a function for emitting masked register writes.
Note that the mask is implemented through byte enables,
so can only mask off aligned 8bit sets of bits.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606191504.18099-10-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
|
|
Add a helper for emitting a number of DSB NOOPs commands.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606191504.18099-9-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
|
|
Add some defines to specify what goes inside certain DSB
instructions.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606191504.18099-6-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
|
|
Define all the DSB register bits so I don't have to look through
bspec to find them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606191504.18099-5-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
|
|
Avoid the locking overhead for DSB registers. We don't need the locks
and intel_dsb_commit() in particular needs to be called from the
vblank evade critical section and thus needs to be fast.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230606191504.18099-3-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
|
|
Commit ade8a0f59844 ("drm/i915: Make all GPU resets atomic") added a
preempt disable section over the hardware reset callback to prepare the
driver for being able to reset from atomic contexts.
In retrospect I can see that the work item at a time was about removing
the struct mutex from the reset path. Code base also briefly entertained
the idea of doing the reset under stop_machine in order to serialize
userspace mmap and temporary glitch in the fence registers (see
eb8d0f5af4ec ("drm/i915: Remove GPU reset dependence on struct_mutex"),
but that never materialized and was soon removed in 2caffbf11762
("drm/i915: Revoke mmaps and prevent access to fence registers across
reset") and replaced with a SRCU based solution.
As such, as far as I can see, today we still have a requirement that
resets must not sleep (invoked from submission tasklets), but no need to
support invoking them from a truly atomic context.
Given that the preemption section is problematic on RT kernels, since the
uncore lock becomes a sleeping lock and so is invalid in such section,
lets try and remove it. Potential downside is that our short waits on GPU
to complete the reset may get extended if CPU scheduling interferes, but
in practice that probably isn't a deal breaker.
In terms of mechanics, since the preemption disabled block is being
removed we just need to replace a few of the wait_for_atomic macros into
busy looping versions which will work (and not complain) when called from
non-atomic sections.
v2:
* Fix timeouts which are now in us. (Andi)
* Update one comment as a drive by. (Andi)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris.p.wilson@intel.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230926100855.61722-1-tvrtko.ursulin@linux.intel.com
|
|
Ideally the busyness worker should take a gt pm wakeref because the
worker only needs to be active while gt is awake. However, the gt_park
path cancels the worker synchronously and this complicates the flow if
the worker is also running at the same time. The cancel waits for the
worker and when the worker releases the wakeref, that would call gt_park
and would lead to a deadlock.
The resolution is to take the global pm wakeref if runtime pm is already
active. If not, we don't need to update the busyness stats as the stats
would already be updated when the gt was parked.
Note:
- We do not requeue the worker if we cannot take a reference to runtime
pm since intel_guc_busyness_unpark would requeue the worker in the
resume path.
- If the gt was parked longer than time taken for GT timestamp to roll
over, we ignore those rollovers since we don't care about tracking the
exact GT time. We only care about roll overs when the gt is active and
running workloads.
- There is a window of time between gt_park and runtime suspend, where
the worker may run. This is acceptable since the worker will not find
any new data to update busyness.
v2: (Daniele)
- Edit commit message and code comment
- Use runtime pm in the worker
- Put runtime pm after enabling the worker
- Use Link tag and add Fixes tag
v3: (Daniele)
- Reword commit and comments and add details
Link: https://gitlab.freedesktop.org/drm/intel/-/issues/7077
Fixes: 77cdd054dd2c ("drm/i915/pmu: Connect engine busyness stats from GuC to pmu")
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230925192117.2497058-1-umesh.nerlige.ramappa@intel.com
|
|
Avoid including the world from headers when forward declarations
suffice.
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230921155325.3851197-1-jani.nikula@intel.com
|
|
Convert aux_ch_name() to a helper that prints a string to a caller
provided buffer, and use it to get more consistent aux channel
debugs. Now that all users of aux_ch_name() are in intel_dp_aux.c, we
can make it static too.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230922105645.3991066-1-jani.nikula@intel.com
|
|
There is no reason to add gtt_offset to the cached head/tail pointers
stream->oa_buffer.head and stream->oa_buffer.tail. This causes the code to
constantly add gtt_offset and subtract gtt_offset and is error
prone.
It is much simpler to maintain stream->oa_buffer.head and
stream->oa_buffer.tail without adding gtt_offset to them and just allow for
the gtt_offset when reading/writing from/to HW registers.
v2: Minor tweak to commit message due to dropping patch in previous series
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Reviewed-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230920040211.2351279-1-ashutosh.dixit@intel.com
|
|
Rename struct drm_gpuvm within struct nouveau_uvmm from 'umgr' to base.
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230920144343.64830-4-dakr@redhat.com
|
|
Currently, the DRM GPUVM does not have any core dependencies preventing
a module build.
Also, new features from subsequent patches require helpers (namely
drm_exec) which can be built as module.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230920144343.64830-3-dakr@redhat.com
|
|
Rename struct drm_gpuva_manager to struct drm_gpuvm including
corresponding functions. This way the GPUVA manager's structures align
very well with the documentation of VM_BIND [1] and VM_BIND locking [2].
It also provides a better foundation for the naming of data structures
and functions introduced for implementing a common dma-resv per GPU-VM
including tracking of external and evicted objects in subsequent
patches.
[1] Documentation/gpu/drm-vm-bind-async.rst
[2] Documentation/gpu/drm-vm-bind-locking.rst
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230920144343.64830-2-dakr@redhat.com
|
|
Based on grepping through the source code this driver appears to be
missing a call to drm_atomic_helper_shutdown() at system shutdown
time. Among other things, this means that if a panel is in use that it
won't be cleanly powered off at system shutdown time.
The fact that we should call drm_atomic_helper_shutdown() in the case
of OS shutdown/restart comes straight out of the kernel doc "driver
instance overview" in drm_drv.c.
Suggested-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com>
Reviewed-by: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230921122641.RFT.v2.1.I134336fce7eac5a63bdac46d57b0888858fc8081@changeid
|
|
Drop UGM per set fragment threshold to 3
BSpec: 54833
Signed-off-by: Shekhar Chauhan <shekhar.chauhan@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
[mattrope: moved above xehpsdv block for consistency]
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230922155356.583595-1-shekhar.chauhan@intel.com
|
|
Starting with Xe_LP+, GFX_MSTR_IRQ contains status bits that have W1C
behavior. If we do not properly reset them, we would miss delivery of
interrupts if a pending bit is set when enabling IRQs.
As an example, the display part of our probe routine contains paths
where we wait for vblank interrupts. If a display interrupt was already
pending when enabling IRQs, we would time out waiting for the vblank.
Avoid the potential issue by clearing GFX_MSTR_IRQ as part of the IRQ
reset.
v2:
- Move logic from gen11_gt_irq_reset() to dg1_irq_reset(). (Matt)
BSpec: 50875, 54028
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230920195351.59421-2-gustavo.sousa@intel.com
|
|
Just let the compiler decide what's best. Turns out absolutely nothing
changes in the output with the inlines removed.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230921160637.3862597-1-jani.nikula@intel.com
|
|
Recent refactoring left an unsightly block of empty lines. Remove them.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Dnyaneshwar Bhadane <dnyaneshwar.bhadane@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230920085715.6905-1-tvrtko.ursulin@linux.intel.com
|
|
For the no-interrupt design (sink device is panel, polling HPD
status when chip power on), anx7625 FW has more than 200ms HPD
de-bounce time in FW, for the safety to get HPD status, driver
better to wait 200ms before HPD detection after OS resume back.
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230922093450.3574349-1-xji@analogixsemi.com
|
|
It's actively harmful to add static inlines in headers that require you
to pull in more headers. Remove the include added in commit f1530f912ed8
("drm/i915/gt: Apply workaround 22016122933 correctly"). We see that
there's already an implicit dependency on the i915_drv.h that we need to
address too.
Cc: Andi Shyti <andi.shyti@linux.intel.com>
Cc: Fei Yang <fei.yang@intel.com>
Cc: Jonathan Cavitt <jonathan.cavitt@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230921162456.3889375-1-jani.nikula@intel.com
|
|
Multiple power domains need to be handled explicitly in each driver. The
driver core can not handle it automatically since it is not aware of
power sequencing requirements the hardware might have. This is not a
problem for simpledrm since everything is expected to be powered on by
the bootloader. simpledrm has just ensure it remains powered on during
its lifetime.
This is required on Apple silicon M2 and M2 Pro/Max/Ultra desktop
systems. The HDMI output initialized by the bootloader requires keeping
the display controller and a DP phy power domain on.
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Eric Curtin <ecurtin@redhat.com>
Reviewed-by: Neal Gompa <neal@gompa.dev>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230912-simpledrm-multiple-power-domains-v2-1-01b66bfb1980@jannau.net
|
|
Once a BO is attached with slicing configuration that BO can only be used
for that particular setting. With this new feature user can detach slicing
configuration off an already sliced BO and attach new slicing configuration
using QAIC_ATTACH_SLICE_BO.
This will support BO recycling.
detach_slice_bo() detaches slicing configuration from a BO. This new
helper function can also be used in release_dbc() as we are doing the
exact same thing.
Signed-off-by: Pranjal Ramajor Asha Kanojiya <quic_pkanojiy@quicinc.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
[jhugo: add documentation for new ioctl]
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901172247.11410-8-quic_jhugo@quicinc.com
|
|
This makes sure that we have a single place to initialize and
re-initialize BO.
Use this new API to cleanup release_dbc()
We will need this for next patch to detach slicing to a BO.
Signed-off-by: Pranjal Ramajor Asha Kanojiya <quic_pkanojiy@quicinc.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901172247.11410-7-quic_jhugo@quicinc.com
|
|
Variables that are set while adding the corresponding BO in transfer list
should be cleaned when flushing them out of transfer list prematurely.
After this patch we do not need some of the cleanup done in release_dbc()
This patch would also pave the way to have a central location to clean BO,
during an undesired situation.
Signed-off-by: Pranjal Ramajor Asha Kanojiya <quic_pkanojiy@quicinc.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901172247.11410-6-quic_jhugo@quicinc.com
|
|
qaic_attach_slicing_bo() updates slicing config on BO. Use the existing
function qaic_free_slices_bo() to remove slicing config done in
qaic_attach_slicing_bo().
Use qaic_free_slices_bo() to cleanup release_dbc()
This would be helpful when we introduce a new IOCTL to detach slicing
configuration onto a BO.
Signed-off-by: Pranjal Ramajor Asha Kanojiya <quic_pkanojiy@quicinc.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901172247.11410-5-quic_jhugo@quicinc.com
|
|
Once the BO is declared 'sliced' by setting bo->sliced to true we can
perform DMA (QAIC_EXECUTE_BO) operation on that BO. Hence we should
declare a BO sliced after completing all the operations.
Adding BO to its respective DBC list in qaic_attach_slicing_bo() seems
out of place as qaic_attach_slicing_bo() should just update BO with
slicing configuration.
Signed-off-by: Pranjal Ramajor Asha Kanojiya <quic_pkanojiy@quicinc.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901172247.11410-4-quic_jhugo@quicinc.com
|
|
Update/Clean up BO metadata in a central location, this will help maintain
the code and looks cleaner.
Use qaic_unprepare_bo() to cleanup release_dbc()
Next few patches will be implementing detach IOCTL which will leverage
this patch.
Signed-off-by: Pranjal Ramajor Asha Kanojiya <quic_pkanojiy@quicinc.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901172247.11410-3-quic_jhugo@quicinc.com
|
|
->size field in struct qaic_bo stores user requested buffer size for
allocate path or size of the dmabuf(PRIME). Now for allocate path driver
allocates a BO of size which is PAGE_SIZE aligned, this size is already
stored in base BO structure (struct drm_gem_object).
So difference is ->size of struct qaic_bo stores the raw value coming from
user and ->size in struct drm_gem_object stores the PAGE_SZIE aligned size.
Do not use ->size from struct qaic_bo for any validation or operation
instead use ->size from struct drm_gem_object since we already have
allocated that much memory then why not use it. Only validate if user
is trying to use more then the BO size. This make the driver more flexible.
After this change ->size field of struct qaic_bo becomes redundant. Remove
it.
Signed-off-by: Pranjal Ramajor Asha Kanojiya <quic_pkanojiy@quicinc.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901172247.11410-2-quic_jhugo@quicinc.com
|
|
Separate the printing of display version and feature flags from the main
driver probe to inside the display initialization. This is in alignment
with isolating the display code from the main driver and helps Xe driver
to resuse it.
v2: Replace drm_info_printer with drm_debug_printer (Jani)
Signed-off-by: Balasubramani Vivekanandan <balasubramani.vivekanandan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230921105954.2002469-1-balasubramani.vivekanandan@intel.com
|
|
The driver uses a naming convention where functions for struct drm_*_funcs
callbacks are named ssd130x_$object_$operation, while the callbacks for
struct drm_*_helper_funcs are named ssd130x_$object_helper_$operation.
The idea is that this helper_ prefix in the function names denote that are
for struct drm_*_helper_funcs callbacks. This convention was copied from
other drivers when ssd130x was written, but Maxime pointed out that is the
exception rather than the norm.
So let's get rid of the _helper prefixes from the function handlers names.
Suggested-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230914195138.1518065-1-javierm@redhat.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v6.7-rc1:
UAPI Changes:
- Nouveau changed to not set NO_PREFETCH flag explicitly.
Cross-subsystem Changes:
- Update documentation of dma-buf intro and uapi.
- fbdev/sbus fixes.
- Use initializer macros in a lot of fbdev drivers.
- Add Boris Brezillon as Panfrost driver maintainer.
- Add Jessica Zhang as drm/panel reviewer.
- Make more fbdev drivers use fb_ops helpers for deferred io.
- Small hid trailing whitespace fix.
- Use fb_ops in hid/picolcd
Core Changes:
- Assorted small fixes to ttm tests, drm/mst.
- Documentation updates to bridge.
- Add kunit tests for some drm_fb functions.
- Rework drm_debugfs implementation.
- Update xe documentation to mark todos as completed.
Driver Changes:
- Add support to rockchip for rv1126 mipi-dsi and vop.
- Assorted small fixes to nouveau, bridge/samsung-dsim,
bridge/lvds-codec, loongson, rockchip, panfrost, gma500, repaper,
komeda, virtio, ssd130x.
- Add support for simple panels Mitsubishi AA084XE01,
JDI LPM102A188A,
- Documentation updates to accel/ivpu.
- Some nouveau scheduling/fence fixes.
- Power management related fixes and other fixes to ivpu.
- Assorted bridge/it66121 fixes.
- Make platform drivers return void in remove() callback.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/3da6554b-3b47-fe7d-c4ea-21f4f819dbb6@linux.intel.com
|
|
We have the same h/vsync_end vs. h/vtotal quirk in the VBT parser
that was also present in EDID parser. Adjust the VBT parser the
same way as was done for hte EDID parser to fixup h/vsync_end
instead of h/vtotal. While I'm not currently aware of any machines
that need this for the VBT it seems prudent to keep both parsers
in sync.
And while at it let's add some debugs here as well. A bit
lackluster but didn't feel like plumbing the connector all
the way down at this time.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230920211934.14920-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
There is an assertion in ggtt_reserve_guc_top that the global GTT
is of size at least GUC_GGTT_TOP, which is not the case on a 32-bit
platform; see commit 562d55d991b39ce376c492df2f7890fd6a541ffc
("drm/i915/bdw: Only use 2g GGTT for 32b platforms"). If GEM_BUG_ON
is enabled, this triggers a BUG(); if GEM_BUG_ON is disabled, the
subsequent reservation fails and the driver fails to initialise
the device:
i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Failed to reserve top of GGTT for GuC
i915 0000:00:02.0: Device initialization failed (-28)
i915 0000:00:02.0: Please file a bug on drm/i915; see https://gitlab.freedesktop.org/drm/intel/-/wikis/How-to-file-i915-bugs for details.
i915: probe of 0000:00:02.0 failed with error -28
Make the reservation at the top of the available space, whatever
that is, instead of assuming that the top will be GUC_GGTT_TOP.
Fixes: 911800765ef6 ("drm/i915/uc: Reserve upper range of GGTT")
Link: https://gitlab.freedesktop.org/drm/intel/-/issues/9080
Signed-off-by: Javier Pello <devel@otheo.eu>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Fernando Pacheco <fernando.pacheco@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: stable@vger.kernel.org # v5.3+
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230902171039.2229126186d697dbcf62d6d8@otheo.eu
|
|
There are some weird EDIDs floating around that have the sync
pulse extending beyond the end of the blanking period.
On the currently problemtic machine (HP Omni 120) EDID reports
the following mode:
"1600x900": 60 108000 1600 1780 1860 1800 900 910 913 1000 0x40 0x5
which is then "corrected" to have htotal=1861 by the current drm_edid.c
code.
The fixup code was originally added in commit 7064fef56369 ("drm: work
around EDIDs with bad htotal/vtotal values"). Googling around we end up in
https://bugs.launchpad.net/ubuntu/hardy/+source/xserver-xorg-video-intel/+bug/297245
where we find an EDID for a Dell Studio 15, which reports:
(II) VESA(0): clock: 65.0 MHz Image Size: 331 x 207 mm
(II) VESA(0): h_active: 1280 h_sync: 1328 h_sync_end 1360 h_blank_end 1337 h_border: 0
(II) VESA(0): v_active: 800 v_sync: 803 v_sync_end 809 v_blanking: 810 v_border: 0
Note that if we use the hblank size (as opposed of the hsync_end)
from the DTD to determine htotal we get exactly 60Hz refresh rate in
both cases, whereas using hsync_end to determine htotal we get a
slightly lower refresh rates. This makes me believe the using the
hblank size is what was intended even in those cases.
Also note that in case of the HP Onmi 120 the VBIOS boots with these:
crtc timings: 108000 1600 1780 1860 1800 900 910 913 1000, type: 0x40 flags: 0x5
ie. it just blindly stuffs the bogus hsync_end and htotal from the DTD
into the transcoder timing registers, and the display works. I believe
the (at least more modern) hardware will automagically terminate the hsync
pulse when the timing generator reaches htotal, which again points that we
should use the hblank size to determine htotal. Unfortunatley the old bug
reports for the Dell machines are extremely lacking in useful details so
we have no idea what kind of timings the VBIOS programmed into the
hardware :(
Let's just flip this quirk around and reduce the length of the sync
pulse instead of extending the blanking period. This at least seems
to be the correct thing to do on more modern hardware. And if any
issues crop up on older hardware we need to debug them properly.
v2: Add debug message breadcrumbs (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8895
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230920211934.14920-1-ville.syrjala@linux.intel.com
|
|
Based on grepping through the source code this driver appears to be
missing a call to drm_atomic_helper_shutdown() at system shutdown time
and at driver unbind time. Among other things, this means that if a
panel is in use that it won't be cleanly powered off at system
shutdown time.
The fact that we should call drm_atomic_helper_shutdown() in the case
of OS shutdown/restart and at driver remove (or unbind) time comes
straight out of the kernel doc "driver instance overview" in
drm_drv.c.
I have attempted to put this in the right place at unbind time. In
most other DRM drivers the call is made right after the call to
drm_kms_helper_poll_fini(), so I've put it there. That means that this
call will also be made in the case that we hit errors in bind, since
kirin_drm_kms_cleanup() is called both in the bind error path and in
unbind. I believe this is harmless even though it's not needed in the
bind error path.
For handling shutdown, we rely on the common technique of seeing if
the drvdata is NULL to know whether we need to call
drm_atomic_helper_shutdown(). This makes it important to make sure
that the drvdata is NULL if bind failed or if unbind was called. We
don't need the actual check for NULL and we'll rely on the patch
("drm/atomic-helper: drm_atomic_helper_shutdown(NULL) should be a
noop").
Suggested-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901163944.RFT.6.I21e0916bbd276033f7d31979c0da171458dedd4d@changeid
|
|
Based on grepping through the source code these drivers appear to be
missing a call to drm_atomic_helper_shutdown() at system shutdown time
and at driver remove (or unbind) time. Among other things, this means
that if a panel is in use that it won't be cleanly powered off at
system shutdown time.
The fact that we should call drm_atomic_helper_shutdown() in the case
of OS shutdown/restart and at driver remove (or unbind) time comes
straight out of the kernel doc "driver instance overview" in
drm_drv.c.
A few notes about these fixes:
- I confirmed that these drivers were all DRIVER_MODESET type drivers,
which I believe makes this relevant.
- I confirmed that these drivers were all DRIVER_ATOMIC.
- When adding drm_atomic_helper_shutdown() to the remove/unbind path,
I added it after drm_kms_helper_poll_fini() when the driver had
it. This seemed to be what other drivers did. If
drm_kms_helper_poll_fini() wasn't there I added it straight after
drm_dev_unregister().
- This patch deals with drivers using the component model in similar
ways as the patch ("drm: Call drm_atomic_helper_shutdown() at
shutdown time for misc drivers")
- These fixes rely on the patch ("drm/atomic-helper:
drm_atomic_helper_shutdown(NULL) should be a noop") to simplify
shutdown.
Suggested-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> # tilcdc
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901163944.RFT.5.I771eb4bd03d8772b19e7dcfaef3e2c167bce5846@changeid
|
|
Based on grepping through the source code, this driver appears to be
missing a call to drm_atomic_helper_shutdown() at remove time. Let's
add it.
The fact that we should call drm_atomic_helper_shutdown() in the case
of OS driver remove comes straight out of the kernel doc "driver
instance overview" in drm_drv.c.
Suggested-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901163944.RFT.4.I4752a39ad9f8fd08b32c2b78a8a3e40491bfb5eb@changeid
|
|
Based on grepping through the source code these drivers appear to be
missing a call to drm_atomic_helper_shutdown() at system shutdown
time. Among other things, this means that if a panel is in use that it
won't be cleanly powered off at system shutdown time.
The fact that we should call drm_atomic_helper_shutdown() in the case
of OS shutdown/restart comes straight out of the kernel doc "driver
instance overview" in drm_drv.c.
Suggested-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901163944.RFT.3.I10dbe099fb1059d304ba847d19fc45054f7ffe9f@changeid
|
|
Based on grepping through the source code these drivers appear to be
missing a call to drm_atomic_helper_shutdown() at system shutdown
time. Among other things, this means that if a panel is in use that it
won't be cleanly powered off at system shutdown time.
The fact that we should call drm_atomic_helper_shutdown() in the case
of OS shutdown/restart comes straight out of the kernel doc "driver
instance overview" in drm_drv.c.
All of the drivers in this patch were fairly straightforward to fix
since they already had a call to drm_atomic_helper_shutdown() at
remove/unbind time but were just lacking one at system shutdown. The
only hitch is that some of these drivers use the component model to
register/unregister their DRM devices. The shutdown callback is part
of the original device. The typical solution here, based on how other
DRM drivers do this, is to keep track of whether the device is bound
based on drvdata. In most cases the drvdata is the drm_device, so we
can just make sure it is NULL when the device is not bound. In some
drivers, this required minor code changes. To make things simpler,
drm_atomic_helper_shutdown() has been modified to consider a NULL
drm_device as a noop in the patch ("drm/atomic-helper:
drm_atomic_helper_shutdown(NULL) should be a noop").
Suggested-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Sui Jingfeng <suijingfeng@loongson.cn>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901163944.RFT.2.I9115e5d094a43e687978b0699cc1fe9f2a3452ea@changeid
|
|
Based on grepping through the source code this driver appears to be
missing a call to drm_atomic_helper_shutdown() at system shutdown
time. Among other things, this means that if a panel is in use that it
won't be cleanly powered off at system shutdown time.
The fact that we should call drm_atomic_helper_shutdown() in the case
of OS shutdown/restart comes straight out of the kernel doc "driver
instance overview" in drm_drv.c.
This driver was fairly easy to update. The drm_device is stored in the
drvdata so we just have to make sure the drvdata is NULL whenever the
device is not bound. To make things simpler,
drm_atomic_helper_shutdown() has been modified to consider a NULL
drm_device as a noop in the patch ("drm/atomic-helper:
drm_atomic_helper_shutdown(NULL) should be a noop").
Suggested-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230901164111.RFT.1.I3d5598bd73a59b5ded71430736c93f67dc5dea61@changeid
|
|
Introduce correspondent definitions for choosing between CD2X CDCLK
and PLL CDCLK as a source. All the entries in cdclk table for xe2lpd are
defined with PLL CDCLK as source, so simply set it. Also
skl_cdclk_decimal() shouldn't be set in CDCLK_CTL anymore, so skip it
for display version 20 and above.
v2:
- Remove unneeded comment and use REG_BIT() (Matt Roper)
- Rename CDCLK_SOURCE_SEL_CDCLK_PLL() to MDCLK_SOURCE_SEL_CDCLK_PLL
to match spec (Lucas)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230919192128.2045154-22-lucas.demarchi@intel.com
|
|
Xe2_LPD supports DC5, DC6, and DC9 (DC3CO no longer exists). The
overall programming and requirements to enter DC states are similar to
those of Xe_LPD+ although AUX transactions do not require DC5/DC6 exit
as they did previously.
Bspec: 68851, 68857, 68886, 69115
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230919192128.2045154-21-lucas.demarchi@intel.com
|
