4562 files changed, 200569 insertions, 206525 deletions

diff --git a/arch/arm/Kbuild b/arch/arm/Kbuild
index b506622e7e23..69de6b6243c7 100644
--- a/arch/arm/Kbuild
+++ b/arch/arm/Kbuild
@@ -1,7 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0-only
 obj-$(CONFIG_FPE_NWFPE)		+= nwfpe/
 # Put arch/arm/fastfpe/ to use this.
-obj-$(CONFIG_FPE_FASTFPE)	+= $(patsubst $(srctree)/$(src)/%,%,$(wildcard $(srctree)/$(src)/fastfpe/))
+obj-$(CONFIG_FPE_FASTFPE)	+= $(patsubst $(src)/%,%,$(wildcard $(src)/fastfpe/))
 obj-$(CONFIG_VFP)		+= vfp/
 obj-$(CONFIG_XEN)		+= xen/
 obj-$(CONFIG_VDSO)		+= vdso/
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 2e8091e2d8a8..45d29320196f 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -5,8 +5,13 @@ config ARM
 	select ARCH_32BIT_OFF_T
 	select ARCH_CORRECT_STACKTRACE_ON_KRETPROBE if HAVE_KRETPROBES && FRAME_POINTER && !ARM_UNWIND
 	select ARCH_HAS_BINFMT_FLAT
+	select ARCH_HAS_CACHE_LINE_SIZE if OF
+	select ARCH_HAS_CPU_CACHE_ALIASING
+	select ARCH_HAS_CPU_FINALIZE_INIT if MMU
 	select ARCH_HAS_CURRENT_STACK_POINTER
 	select ARCH_HAS_DEBUG_VIRTUAL if MMU
+	select ARCH_HAS_DMA_ALLOC if MMU
+	select ARCH_HAS_DMA_OPS
 	select ARCH_HAS_DMA_WRITE_COMBINE if !ARM_DMA_MEM_BUFFERABLE
 	select ARCH_HAS_ELF_RANDOMIZE
 	select ARCH_HAS_FORTIFY_SOURCE
@@ -15,25 +20,27 @@ config ARM
 	select ARCH_HAS_MEMBARRIER_SYNC_CORE
 	select ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE
 	select ARCH_HAS_PTE_SPECIAL if ARM_LPAE
-	select ARCH_HAS_PHYS_TO_DMA
 	select ARCH_HAS_SETUP_DMA_OPS
 	select ARCH_HAS_SET_MEMORY
+	select ARCH_STACKWALK
 	select ARCH_HAS_STRICT_KERNEL_RWX if MMU && !XIP_KERNEL
 	select ARCH_HAS_STRICT_MODULE_RWX if MMU
-	select ARCH_HAS_SYNC_DMA_FOR_DEVICE if SWIOTLB || !MMU
-	select ARCH_HAS_SYNC_DMA_FOR_CPU if SWIOTLB || !MMU
+	select ARCH_HAS_SYNC_DMA_FOR_DEVICE
+	select ARCH_HAS_SYNC_DMA_FOR_CPU
 	select ARCH_HAS_TEARDOWN_DMA_OPS if MMU
 	select ARCH_HAS_TICK_BROADCAST if GENERIC_CLOCKEVENTS_BROADCAST
-	select ARCH_HAVE_CUSTOM_GPIO_H
 	select ARCH_HAVE_NMI_SAFE_CMPXCHG if CPU_V7 || CPU_V7M || CPU_V6K
 	select ARCH_HAS_GCOV_PROFILE_ALL
 	select ARCH_KEEP_MEMBLOCK
+	select ARCH_HAS_UBSAN
 	select ARCH_MIGHT_HAVE_PC_PARPORT
-	select ARCH_NO_SG_CHAIN if !ARM_HAS_SG_CHAIN
 	select ARCH_OPTIONAL_KERNEL_RWX if ARCH_HAS_STRICT_KERNEL_RWX
 	select ARCH_OPTIONAL_KERNEL_RWX_DEFAULT if CPU_V7
+	select ARCH_NEED_CMPXCHG_1_EMU if CPU_V6
 	select ARCH_SUPPORTS_ATOMIC_RMW
+	select ARCH_SUPPORTS_CFI
 	select ARCH_SUPPORTS_HUGETLBFS if ARM_LPAE
+	select ARCH_SUPPORTS_PER_VMA_LOCK
 	select ARCH_USE_BUILTIN_BSWAP
 	select ARCH_USE_CMPXCHG_LOCKREF
 	select ARCH_USE_MEMTEST
@@ -43,12 +50,12 @@ config ARM
 	select ARCH_WANT_LD_ORPHAN_WARN
 	select BINFMT_FLAT_ARGVP_ENVP_ON_STACK
 	select BUILDTIME_TABLE_SORT if MMU
+	select COMMON_CLK if !(ARCH_RPC || ARCH_FOOTBRIDGE)
 	select CLONE_BACKWARDS
 	select CPU_PM if SUSPEND || CPU_IDLE
 	select DCACHE_WORD_ACCESS if HAVE_EFFICIENT_UNALIGNED_ACCESS
 	select DMA_DECLARE_COHERENT
 	select DMA_GLOBAL_POOL if !MMU
-	select DMA_OPS
 	select DMA_NONCOHERENT_MMAP if MMU
 	select EDAC_SUPPORT
 	select EDAC_ATOMIC_SCRUB
@@ -58,6 +65,7 @@ config ARM
 	select GENERIC_CLOCKEVENTS_BROADCAST if SMP
 	select GENERIC_IRQ_IPI if SMP
 	select GENERIC_CPU_AUTOPROBE
+	select GENERIC_CPU_DEVICES
 	select GENERIC_EARLY_IOREMAP
 	select GENERIC_IDLE_POLL_SETUP
 	select GENERIC_IRQ_MULTI_HANDLER
@@ -69,12 +77,15 @@ config ARM
 	select GENERIC_SCHED_CLOCK
 	select GENERIC_SMP_IDLE_THREAD
 	select HARDIRQS_SW_RESEND
+	select HAS_IOPORT
 	select HAVE_ARCH_AUDITSYSCALL if AEABI && !OABI_COMPAT
 	select HAVE_ARCH_BITREVERSE if (CPU_32v7M || CPU_32v7) && !CPU_32v6
-	select HAVE_ARCH_JUMP_LABEL if !XIP_KERNEL && !CPU_ENDIAN_BE32 && MMU
+	select HAVE_ARCH_JUMP_LABEL if !XIP_KERNEL && !CPU_ENDIAN_BE32 && MMU && (!PREEMPT_RT || !SMP)
 	select HAVE_ARCH_KFENCE if MMU && !XIP_KERNEL
 	select HAVE_ARCH_KGDB if !CPU_ENDIAN_BE32 && MMU
 	select HAVE_ARCH_KASAN if MMU && !XIP_KERNEL
+	select HAVE_ARCH_KASAN_VMALLOC if HAVE_ARCH_KASAN
+	select HAVE_ARCH_KSTACK_ERASE
 	select HAVE_ARCH_MMAP_RND_BITS if MMU
 	select HAVE_ARCH_PFN_VALID
 	select HAVE_ARCH_SECCOMP
@@ -84,18 +95,20 @@ config ARM
 	select HAVE_ARCH_TRANSPARENT_HUGEPAGE if ARM_LPAE
 	select HAVE_ARM_SMCCC if CPU_V7
 	select HAVE_EBPF_JIT if !CPU_ENDIAN_BE32
-	select HAVE_CONTEXT_TRACKING
+	select HAVE_CONTEXT_TRACKING_USER
 	select HAVE_C_RECORDMCOUNT
 	select HAVE_BUILDTIME_MCOUNT_SORT
 	select HAVE_DEBUG_KMEMLEAK if !XIP_KERNEL
 	select HAVE_DMA_CONTIGUOUS if MMU
+	select HAVE_EXTRA_IPI_TRACEPOINTS
 	select HAVE_DYNAMIC_FTRACE if !XIP_KERNEL && !CPU_ENDIAN_BE32 && MMU
 	select HAVE_DYNAMIC_FTRACE_WITH_REGS if HAVE_DYNAMIC_FTRACE
 	select HAVE_EFFICIENT_UNALIGNED_ACCESS if (CPU_V6 || CPU_V6K || CPU_V7) && MMU
 	select HAVE_EXIT_THREAD
-	select HAVE_FAST_GUP if ARM_LPAE
-	select HAVE_FTRACE_MCOUNT_RECORD if !XIP_KERNEL
+	select HAVE_GUP_FAST if ARM_LPAE
+	select HAVE_FUNCTION_ERROR_INJECTION
 	select HAVE_FUNCTION_GRAPH_TRACER
+	select HAVE_FUNCTION_GRAPH_FREGS
 	select HAVE_FUNCTION_TRACER if !XIP_KERNEL
 	select HAVE_GCC_PLUGINS
 	select HAVE_HW_BREAKPOINT if PERF_EVENTS && (CPU_V6 || CPU_V6K || CPU_V7)
@@ -107,32 +120,42 @@ config ARM
 	select HAVE_KERNEL_XZ
 	select HAVE_KPROBES if !XIP_KERNEL && !CPU_ENDIAN_BE32 && !CPU_V7M
 	select HAVE_KRETPROBES if HAVE_KPROBES
+	select HAVE_LD_DEAD_CODE_DATA_ELIMINATION if (LD_VERSION >= 23600 || LD_IS_LLD) && LD_CAN_USE_KEEP_IN_OVERLAY
 	select HAVE_MOD_ARCH_SPECIFIC
 	select HAVE_NMI
 	select HAVE_OPTPROBES if !THUMB2_KERNEL
+	select HAVE_PAGE_SIZE_4KB
+	select HAVE_PCI if MMU
 	select HAVE_PERF_EVENTS
 	select HAVE_PERF_REGS
 	select HAVE_PERF_USER_STACK_DUMP
 	select MMU_GATHER_RCU_TABLE_FREE if SMP && ARM_LPAE
 	select HAVE_REGS_AND_STACK_ACCESS_API
 	select HAVE_RSEQ
+	select HAVE_RUST if CPU_LITTLE_ENDIAN && CPU_32v7
 	select HAVE_STACKPROTECTOR
 	select HAVE_SYSCALL_TRACEPOINTS
 	select HAVE_UID16
 	select HAVE_VIRT_CPU_ACCOUNTING_GEN
+	select HOTPLUG_CORE_SYNC_DEAD if HOTPLUG_CPU
 	select IRQ_FORCED_THREADING
+	select LOCK_MM_AND_FIND_VMA
 	select MODULES_USE_ELF_REL
 	select NEED_DMA_MAP_STATE
 	select OF_EARLY_FLATTREE if OF
 	select OLD_SIGACTION
 	select OLD_SIGSUSPEND3
+	select PCI_DOMAINS_GENERIC if PCI
 	select PCI_SYSCALL if PCI
 	select PERF_USE_VMALLOC
 	select RTC_LIB
+	select SPARSE_IRQ if !(ARCH_FOOTBRIDGE || ARCH_RPC)
 	select SYS_SUPPORTS_APM_EMULATION
 	select THREAD_INFO_IN_TASK
+	select TIMER_OF if OF
 	select HAVE_ARCH_VMAP_STACK if MMU && ARM_HAS_GROUP_RELOCS
 	select TRACE_IRQFLAGS_SUPPORT if !CPU_V7M
+	select USE_OF if !(ARCH_FOOTBRIDGE || ARCH_RPC || ARCH_SA1100)
 	# Above selects are sorted alphabetically; please add new ones
 	# according to that.  Thanks.
 	help
@@ -144,22 +167,15 @@ config ARM
 	  <http://www.arm.linux.org.uk/>.
 
 config ARM_HAS_GROUP_RELOCS
-	def_bool y
-	depends on !LD_IS_LLD || LLD_VERSION >= 140000
-	depends on !COMPILE_TEST
+	def_bool !COMPILE_TEST
 	help
 	  Whether or not to use R_ARM_ALU_PC_Gn or R_ARM_LDR_PC_Gn group
-	  relocations, which have been around for a long time, but were not
-	  supported in LLD until version 14. The combined range is -/+ 256 MiB,
-	  which is usually sufficient, but not for allyesconfig, so we disable
-	  this feature when doing compile testing.
-
-config ARM_HAS_SG_CHAIN
-	bool
+	  relocations. The combined range is -/+ 256 MiB, which is usually
+	  sufficient, but not for allyesconfig, so we disable this feature
+	  when doing compile testing.
 
 config ARM_DMA_USE_IOMMU
 	bool
-	select ARM_HAS_SG_CHAIN
 	select NEED_SG_DMA_LENGTH
 
 if ARM_DMA_USE_IOMMU
@@ -243,9 +259,9 @@ config ARCH_MTD_XIP
 	bool
 
 config ARM_PATCH_PHYS_VIRT
-	bool "Patch physical to virtual translations at runtime" if EMBEDDED
+	bool "Patch physical to virtual translations at runtime" if !ARCH_MULTIPLATFORM
 	default y
-	depends on !XIP_KERNEL && MMU
+	depends on MMU
 	help
 	  Patch phys-to-virt and virt-to-phys translation functions at
 	  boot and module load time according to the position of the
@@ -274,12 +290,11 @@ config NEED_MACH_MEMORY_H
 
 config PHYS_OFFSET
 	hex "Physical address of main memory" if MMU
-	depends on !ARM_PATCH_PHYS_VIRT
+	depends on !ARM_PATCH_PHYS_VIRT || !AUTO_ZRELADDR
 	default DRAM_BASE if !MMU
 	default 0x00000000 if ARCH_FOOTBRIDGE
 	default 0x10000000 if ARCH_OMAP1 || ARCH_RPC
-	default 0x30000000 if ARCH_S3C24XX
-	default 0xa0000000 if ARCH_IOP32X || ARCH_PXA
+	default 0xa0000000 if ARCH_PXA
 	default 0xc0000000 if ARCH_EP93XX || ARCH_SA1100
 	default 0
 	help
@@ -307,13 +322,8 @@ config MMU
 config ARM_SINGLE_ARMV7M
 	def_bool !MMU
 	select ARM_NVIC
-	select AUTO_ZRELADDR
-	select TIMER_OF
-	select COMMON_CLK
 	select CPU_V7M
 	select NO_IOPORT_MAP
-	select SPARSE_IRQ
-	select USE_OF
 
 config ARCH_MMAP_RND_BITS_MIN
 	default 8
@@ -323,257 +333,22 @@ config ARCH_MMAP_RND_BITS_MAX
 	default 15 if PAGE_OFFSET=0x80000000
 	default 16
 
-#
-# The "ARM system type" choice list is ordered alphabetically by option
-# text.  Please add new entries in the option alphabetic order.
-#
-choice
-	prompt "ARM system type"
-	depends on MMU
-	default ARCH_MULTIPLATFORM
-
 config ARCH_MULTIPLATFORM
-	bool "Allow multiple platforms to be selected"
-	select ARCH_FLATMEM_ENABLE
-	select ARCH_SPARSEMEM_ENABLE
-	select ARCH_SELECT_MEMORY_MODEL
-	select ARM_HAS_SG_CHAIN
-	select ARM_PATCH_PHYS_VIRT
-	select AUTO_ZRELADDR
-	select TIMER_OF
-	select COMMON_CLK
-	select HAVE_PCI
-	select PCI_DOMAINS_GENERIC if PCI
-	select SPARSE_IRQ
-	select USE_OF
-
-config ARCH_EP93XX
-	bool "EP93xx-based"
-	select ARCH_SPARSEMEM_ENABLE
-	select ARM_AMBA
-	imply ARM_PATCH_PHYS_VIRT
-	select ARM_VIC
-	select AUTO_ZRELADDR
-	select CLKSRC_MMIO
-	select CPU_ARM920T
-	select GPIOLIB
-	select COMMON_CLK
-	help
-	  This enables support for the Cirrus EP93xx series of CPUs.
-
-config ARCH_FOOTBRIDGE
-	bool "FootBridge"
-	select CPU_SA110
-	select FOOTBRIDGE
-	select NEED_MACH_MEMORY_H
-	help
-	  Support for systems based on the DC21285 companion chip
-	  ("FootBridge"), such as the Simtec CATS and the Rebel NetWinder.
-
-config ARCH_IOP32X
-	bool "IOP32x-based"
-	select CPU_XSCALE
-	select GPIO_IOP
-	select GPIOLIB
-	select FORCE_PCI
-	select PLAT_IOP
-	help
-	  Support for Intel's 80219 and IOP32X (XScale) family of
-	  processors.
-
-config ARCH_IXP4XX
-	bool "IXP4xx-based"
-	select ARCH_SUPPORTS_BIG_ENDIAN
-	select ARM_PATCH_PHYS_VIRT
-	select CPU_XSCALE
-	select GPIO_IXP4XX
-	select GPIOLIB
-	select HAVE_PCI
-	select IXP4XX_IRQ
-	select IXP4XX_TIMER
-	select SPARSE_IRQ
-	select USB_EHCI_BIG_ENDIAN_DESC
-	select USB_EHCI_BIG_ENDIAN_MMIO
-	help
-	  Support for Intel's IXP4XX (XScale) family of processors.
-
-config ARCH_DOVE
-	bool "Marvell Dove"
-	select CPU_PJ4
-	select GPIOLIB
-	select HAVE_PCI
-	select MVEBU_MBUS
-	select PINCTRL
-	select PINCTRL_DOVE
-	select PLAT_ORION_LEGACY
-	select SPARSE_IRQ
-	select PM_GENERIC_DOMAINS if PM
-	help
-	  Support for the Marvell Dove SoC 88AP510
-
-config ARCH_PXA
-	bool "PXA2xx/PXA3xx-based"
-	select ARCH_MTD_XIP
-	select ARM_CPU_SUSPEND if PM
-	select AUTO_ZRELADDR
-	select COMMON_CLK
-	select CLKSRC_PXA
-	select CLKSRC_MMIO
-	select TIMER_OF
-	select CPU_XSCALE if !CPU_XSC3
-	select GPIO_PXA
-	select GPIOLIB
-	select IRQ_DOMAIN
-	select PLAT_PXA
-	select SPARSE_IRQ
-	help
-	  Support for Intel/Marvell's PXA2xx/PXA3xx processor line.
-
-config ARCH_RPC
-	bool "RiscPC"
-	depends on !CC_IS_CLANG && GCC_VERSION < 90100 && GCC_VERSION >= 60000
-	select ARCH_ACORN
-	select ARCH_MAY_HAVE_PC_FDC
-	select ARCH_SPARSEMEM_ENABLE
-	select ARM_HAS_SG_CHAIN
-	select CPU_SA110
-	select FIQ
-	select HAVE_PATA_PLATFORM
-	select ISA_DMA_API
-	select LEGACY_TIMER_TICK
-	select NEED_MACH_IO_H
-	select NEED_MACH_MEMORY_H
-	select NO_IOPORT_MAP
-	help
-	  On the Acorn Risc-PC, Linux can support the internal IDE disk and
-	  CD-ROM interface, serial and parallel port, and the floppy drive.
-
-config ARCH_SA1100
-	bool "SA1100-based"
-	select ARCH_MTD_XIP
-	select ARCH_SPARSEMEM_ENABLE
-	select CLKSRC_MMIO
-	select CLKSRC_PXA
-	select TIMER_OF if OF
-	select COMMON_CLK
-	select CPU_FREQ
-	select CPU_SA1100
-	select GPIOLIB
-	select IRQ_DOMAIN
-	select ISA
-	select NEED_MACH_MEMORY_H
-	select SPARSE_IRQ
-	help
-	  Support for StrongARM 11x0 based boards.
-
-config ARCH_S3C24XX
-	bool "Samsung S3C24XX SoCs"
-	select ATAGS
-	select CLKSRC_SAMSUNG_PWM
-	select GPIO_SAMSUNG
-	select GPIOLIB
-	select NEED_MACH_IO_H
-	select S3C2410_WATCHDOG
-	select SAMSUNG_ATAGS
-	select USE_OF
-	select WATCHDOG
-	help
-	  Samsung S3C2410, S3C2412, S3C2413, S3C2416, S3C2440, S3C2442, S3C2443
-	  and S3C2450 SoCs based systems, such as the Simtec Electronics BAST
-	  (<http://www.simtec.co.uk/products/EB110ITX/>), the IPAQ 1940 or the
-	  Samsung SMDK2410 development board (and derivatives).
-
-config ARCH_OMAP1
-	bool "TI OMAP1"
-	select ARCH_OMAP
-	select CLKSRC_MMIO
-	select GENERIC_IRQ_CHIP
-	select GPIOLIB
-	select HAVE_LEGACY_CLK
-	select IRQ_DOMAIN
-	select NEED_MACH_IO_H if PCCARD
-	select NEED_MACH_MEMORY_H
-	select SPARSE_IRQ
-	help
-	  Support for older TI OMAP1 (omap7xx, omap15xx or omap16xx)
-
-endchoice
-
-menu "Multiple platform selection"
-	depends on ARCH_MULTIPLATFORM
-
-comment "CPU Core family selection"
-
-config ARCH_MULTI_V4
-	bool "ARMv4 based platforms (FA526)"
-	depends on !ARCH_MULTI_V6_V7
-	select ARCH_MULTI_V4_V5
-	select CPU_FA526
-
-config ARCH_MULTI_V4T
-	bool "ARMv4T based platforms (ARM720T, ARM920T, ...)"
-	depends on !ARCH_MULTI_V6_V7
-	select ARCH_MULTI_V4_V5
-	select CPU_ARM920T if !(CPU_ARM7TDMI || CPU_ARM720T || \
-		CPU_ARM740T || CPU_ARM9TDMI || CPU_ARM922T || \
-		CPU_ARM925T || CPU_ARM940T)
-
-config ARCH_MULTI_V5
-	bool "ARMv5 based platforms (ARM926T, XSCALE, PJ1, ...)"
-	depends on !ARCH_MULTI_V6_V7
-	select ARCH_MULTI_V4_V5
-	select CPU_ARM926T if !(CPU_ARM946E || CPU_ARM1020 || \
-		CPU_ARM1020E || CPU_ARM1022 || CPU_ARM1026 || \
-		CPU_XSCALE || CPU_XSC3 || CPU_MOHAWK || CPU_FEROCEON)
-
-config ARCH_MULTI_V4_V5
-	bool
-
-config ARCH_MULTI_V6
-	bool "ARMv6 based platforms (ARM11)"
-	select ARCH_MULTI_V6_V7
-	select CPU_V6K
-
-config ARCH_MULTI_V7
-	bool "ARMv7 based platforms (Cortex-A, PJ4, Scorpion, Krait)"
+	bool "Require kernel to be portable to multiple machines" if EXPERT
+	depends on MMU && !(ARCH_FOOTBRIDGE || ARCH_RPC || ARCH_SA1100)
 	default y
-	select ARCH_MULTI_V6_V7
-	select CPU_V7
-	select HAVE_SMP
+	help
+	  In general, all Arm machines can be supported in a single
+	  kernel image, covering either Armv4/v5 or Armv6/v7.
 
-config ARCH_MULTI_V6_V7
-	bool
-	select MIGHT_HAVE_CACHE_L2X0
+	  However, some configuration options require hardcoding machine
+	  specific physical addresses or enable errata workarounds that may
+	  break other machines.
 
-config ARCH_MULTI_CPU_AUTO
-	def_bool !(ARCH_MULTI_V4 || ARCH_MULTI_V4T || ARCH_MULTI_V6_V7)
-	select ARCH_MULTI_V5
+	  Selecting N here allows using those options, including
+	  DEBUG_UNCOMPRESS, XIP_KERNEL and ZBOOT_ROM. If unsure, say Y.
 
-endmenu
-
-config ARCH_VIRT
-	bool "Dummy Virtual Machine"
-	depends on ARCH_MULTI_V7
-	select ARM_AMBA
-	select ARM_GIC
-	select ARM_GIC_V2M if PCI
-	select ARM_GIC_V3
-	select ARM_GIC_V3_ITS if PCI
-	select ARM_PSCI
-	select HAVE_ARM_ARCH_TIMER
-	select ARCH_SUPPORTS_BIG_ENDIAN
-
-config ARCH_AIROHA
-	bool "Airoha SoC Support"
-	depends on ARCH_MULTI_V7
-	select ARM_AMBA
-	select ARM_GIC
-	select ARM_GIC_V3
-	select ARM_PSCI
-	select HAVE_ARM_ARCH_TIMER
-	select COMMON_CLK
-	help
-	  Support for Airoha EN7523 SoCs
+source "arch/arm/Kconfig.platforms"
 
 #
 # This is sorted alphabetically by mach-* pathname.  However, plat-*
@@ -586,8 +361,6 @@ source "arch/arm/mach-alpine/Kconfig"
 
 source "arch/arm/mach-artpec/Kconfig"
 
-source "arch/arm/mach-asm9260/Kconfig"
-
 source "arch/arm/mach-aspeed/Kconfig"
 
 source "arch/arm/mach-at91/Kconfig"
@@ -600,8 +373,6 @@ source "arch/arm/mach-berlin/Kconfig"
 
 source "arch/arm/mach-clps711x/Kconfig"
 
-source "arch/arm/mach-cns3xxx/Kconfig"
-
 source "arch/arm/mach-davinci/Kconfig"
 
 source "arch/arm/mach-digicolor/Kconfig"
@@ -622,10 +393,6 @@ source "arch/arm/mach-hisi/Kconfig"
 
 source "arch/arm/mach-imx/Kconfig"
 
-source "arch/arm/mach-integrator/Kconfig"
-
-source "arch/arm/mach-iop32x/Kconfig"
-
 source "arch/arm/mach-ixp4xx/Kconfig"
 
 source "arch/arm/mach-keystone/Kconfig"
@@ -640,8 +407,6 @@ source "arch/arm/mach-milbeaut/Kconfig"
 
 source "arch/arm/mach-mmp/Kconfig"
 
-source "arch/arm/mach-moxart/Kconfig"
-
 source "arch/arm/mach-mstar/Kconfig"
 
 source "arch/arm/mach-mv78xx0/Kconfig"
@@ -654,28 +419,19 @@ source "arch/arm/mach-nomadik/Kconfig"
 
 source "arch/arm/mach-npcm/Kconfig"
 
-source "arch/arm/mach-nspire/Kconfig"
-
-source "arch/arm/plat-omap/Kconfig"
-
 source "arch/arm/mach-omap1/Kconfig"
 
 source "arch/arm/mach-omap2/Kconfig"
 
 source "arch/arm/mach-orion5x/Kconfig"
 
-source "arch/arm/mach-oxnas/Kconfig"
-
 source "arch/arm/mach-pxa/Kconfig"
-source "arch/arm/plat-pxa/Kconfig"
 
 source "arch/arm/mach-qcom/Kconfig"
 
-source "arch/arm/mach-rda/Kconfig"
-
 source "arch/arm/mach-realtek/Kconfig"
 
-source "arch/arm/mach-realview/Kconfig"
+source "arch/arm/mach-rpc/Kconfig"
 
 source "arch/arm/mach-rockchip/Kconfig"
 
@@ -699,14 +455,10 @@ source "arch/arm/mach-sunxi/Kconfig"
 
 source "arch/arm/mach-tegra/Kconfig"
 
-source "arch/arm/mach-uniphier/Kconfig"
-
 source "arch/arm/mach-ux500/Kconfig"
 
 source "arch/arm/mach-versatile/Kconfig"
 
-source "arch/arm/mach-vexpress/Kconfig"
-
 source "arch/arm/mach-vt8500/Kconfig"
 
 source "arch/arm/mach-zynq/Kconfig"
@@ -739,13 +491,9 @@ config ARCH_MPS2
 config ARCH_ACORN
 	bool
 
-config PLAT_IOP
-	bool
-
 config PLAT_ORION
 	bool
 	select CLKSRC_MMIO
-	select COMMON_CLK
 	select GENERIC_IRQ_CHIP
 	select IRQ_DOMAIN
 
@@ -753,9 +501,6 @@ config PLAT_ORION_LEGACY
 	bool
 	select PLAT_ORION
 
-config PLAT_PXA
-	bool
-
 config PLAT_VERSATILE
 	bool
 
@@ -763,8 +508,8 @@ source "arch/arm/mm/Kconfig"
 
 config IWMMXT
 	bool "Enable iWMMXt support"
-	depends on CPU_XSCALE || CPU_XSC3 || CPU_MOHAWK || CPU_PJ4 || CPU_PJ4B
-	default y if PXA27x || PXA3xx || ARCH_MMP || CPU_PJ4 || CPU_PJ4B
+	depends on CPU_XSCALE || CPU_XSC3 || CPU_MOHAWK
+	default y if PXA27x || PXA3xx || ARCH_MMP
 	help
 	  Enable support for iWMMXt context switching at run time if
 	  running on a CPU that supports it.
@@ -833,7 +578,9 @@ config ARM_ERRATA_458693
 	  hazard might then cause a processor deadlock. The workaround enables
 	  the L1 caching of the NEON accesses and disables the PLD instruction
 	  in the ACTLR register. Note that setting specific bits in the ACTLR
-	  register may not be available in non-secure mode.
+	  register may not be available in non-secure mode and thus is not
+	  available on a multiplatform kernel. This should be applied by the
+	  bootloader instead.
 
 config ARM_ERRATA_460075
 	bool "ARM errata: Data written to the L2 cache can be overwritten with stale data"
@@ -846,7 +593,9 @@ config ARM_ERRATA_460075
 	  and overwritten with stale memory contents from external memory. The
 	  workaround disables the write-allocate mode for the L2 cache via the
 	  ACTLR register. Note that setting specific bits in the ACTLR register
-	  may not be available in non-secure mode.
+	  may not be available in non-secure mode and thus is not available on
+	  a multiplatform kernel. This should be applied by the bootloader
+	  instead.
 
 config ARM_ERRATA_742230
 	bool "ARM errata: DMB operation may be faulty"
@@ -859,7 +608,10 @@ config ARM_ERRATA_742230
 	  ordering of the two writes. This workaround sets a specific bit in
 	  the diagnostic register of the Cortex-A9 which causes the DMB
 	  instruction to behave as a DSB, ensuring the correct behaviour of
-	  the two writes.
+	  the two writes. Note that setting specific bits in the diagnostics
+	  register may not be available in non-secure mode and thus is not
+	  available on a multiplatform kernel. This should be applied by the
+	  bootloader instead.
 
 config ARM_ERRATA_742231
 	bool "ARM errata: Incorrect hazard handling in the SCU may lead to data corruption"
@@ -874,7 +626,10 @@ config ARM_ERRATA_742231
 	  replaced from one of the CPUs at the same time as another CPU is
 	  accessing it. This workaround sets specific bits in the diagnostic
 	  register of the Cortex-A9 which reduces the linefill issuing
-	  capabilities of the processor.
+	  capabilities of the processor. Note that setting specific bits in the
+	  diagnostics register may not be available in non-secure mode and thus
+	  is not available on a multiplatform kernel. This should be applied by
+	  the bootloader instead.
 
 config ARM_ERRATA_643719
 	bool "ARM errata: LoUIS bit field in CLIDR register is incorrect"
@@ -911,7 +666,9 @@ config ARM_ERRATA_743622
 	  register of the Cortex-A9 which disables the Store Buffer
 	  optimisation, preventing the defect from occurring. This has no
 	  visible impact on the overall performance or power consumption of the
-	  processor.
+	  processor. Note that setting specific bits in the diagnostics register
+	  may not be available in non-secure mode and thus is not available on a
+	  multiplatform kernel. This should be applied by the bootloader instead.
 
 config ARM_ERRATA_751472
 	bool "ARM errata: Interrupted ICIALLUIS may prevent completion of broadcasted operation"
@@ -923,6 +680,10 @@ config ARM_ERRATA_751472
 	  completion of a following broadcasted operation if the second
 	  operation is received by a CPU before the ICIALLUIS has completed,
 	  potentially leading to corrupted entries in the cache or TLB.
+	  Note that setting specific bits in the diagnostics register may
+	  not be available in non-secure mode and thus is not available on
+	  a multiplatform kernel. This should be applied by the bootloader
+	  instead.
 
 config ARM_ERRATA_754322
 	bool "ARM errata: possible faulty MMU translations following an ASID switch"
@@ -972,6 +733,17 @@ config ARM_ERRATA_764369
 	  relevant cache maintenance functions and sets a specific bit
 	  in the diagnostic control register of the SCU.
 
+config ARM_ERRATA_764319
+	bool "ARM errata: Read to DBGPRSR and DBGOSLSR may generate Undefined instruction"
+	depends on CPU_V7
+	help
+	  This option enables the workaround for the 764319 Cortex-A9 erratum.
+	  CP14 read accesses to the DBGPRSR and DBGOSLSR registers generate an
+	  unexpected Undefined Instruction exception when the DBGSWENABLE
+	  external pin is set to 0, even when the CP14 accesses are performed
+	  from a privileged mode. This work around catches the exception in a
+	  way the kernel does not stop execution.
+
 config ARM_ERRATA_775420
        bool "ARM errata: A data cache maintenance operation which aborts, might lead to deadlock"
        depends on CPU_V7
@@ -1088,21 +860,10 @@ config ISA
 	  (MCA) or VESA.  ISA is an older system, now being displaced by PCI;
 	  newer boards don't support it.  If you have ISA, say Y, otherwise N.
 
-# Select ISA DMA controller support
-config ISA_DMA
-	bool
-	select ISA_DMA_API
-
 # Select ISA DMA interface
 config ISA_DMA_API
 	bool
 
-config PCI_NANOENGINE
-	bool "BSE nanoEngine PCI support"
-	depends on SA1100_NANOENGINE
-	help
-	  Enable PCI on the BSE nanoEngine board.
-
 config ARM_ERRATA_814220
 	bool "ARM errata: Cache maintenance by set/way operations can execute out of order"
 	depends on CPU_V7
@@ -1145,7 +906,7 @@ config SMP
 	  uniprocessor machines. On a uniprocessor machine, the kernel
 	  will run faster if you say N here.
 
-	  See also <file:Documentation/x86/i386/IO-APIC.rst>,
+	  See also <file:Documentation/arch/x86/i386/IO-APIC.rst>,
 	  <file:Documentation/admin-guide/lockup-watchdogs.rst> and the SMP-HOWTO available at
 	  <http://tldp.org/HOWTO/SMP-HOWTO.html>.
 
@@ -1153,7 +914,7 @@ config SMP
 
 config SMP_ON_UP
 	bool "Allow booting SMP kernel on uniprocessor systems"
-	depends on SMP && !XIP_KERNEL && MMU
+	depends on SMP && MMU
 	default y
 	help
 	  SMP kernels contain instructions which fail on non-SMP processors.
@@ -1176,28 +937,14 @@ config IRQSTACKS
 config ARM_CPU_TOPOLOGY
 	bool "Support cpu topology definition"
 	depends on SMP && CPU_V7
+	select ARCH_SUPPORTS_SCHED_MC
+	select ARCH_SUPPORTS_SCHED_SMT
 	default y
 	help
 	  Support ARM cpu topology definition. The MPIDR register defines
 	  affinity between processors which is then used to describe the cpu
 	  topology of an ARM System.
 
-config SCHED_MC
-	bool "Multi-core scheduler support"
-	depends on ARM_CPU_TOPOLOGY
-	help
-	  Multi-core scheduler support improves the CPU scheduler's decision
-	  making when dealing with multi-core CPU chips at a cost of slightly
-	  increased overhead in some places. If unsure say N here.
-
-config SCHED_SMT
-	bool "SMT scheduler support"
-	depends on ARM_CPU_TOPOLOGY
-	help
-	  Improves the CPU scheduler's decision making when dealing with
-	  MultiThreading at a cost of slightly increased overhead in some
-	  places. If unsure say N here.
-
 config HAVE_ARM_SCU
 	bool
 	help
@@ -1326,27 +1073,6 @@ config ARM_PSCI
 	  0022A ("Power State Coordination Interface System Software on
 	  ARM processors").
 
-# The GPIO number here must be sorted by descending number. In case of
-# a multiplatform kernel, we just want the highest value required by the
-# selected platforms.
-config ARCH_NR_GPIO
-	int
-	default 2048 if ARCH_INTEL_SOCFPGA
-	default 1024 if ARCH_BRCMSTB || ARCH_RENESAS || ARCH_TEGRA || \
-		ARCH_ZYNQ || ARCH_ASPEED
-	default 512 if ARCH_EXYNOS || ARCH_KEYSTONE || SOC_OMAP5 || \
-		SOC_DRA7XX || ARCH_S3C24XX || ARCH_S3C64XX || ARCH_S5PV210
-	default 416 if ARCH_SUNXI
-	default 392 if ARCH_U8500
-	default 352 if ARCH_VT8500
-	default 288 if ARCH_ROCKCHIP
-	default 264 if MACH_H4700
-	default 0
-	help
-	  Maximum number of GPIOs in the system.
-
-	  If unsure, leave the default value.
-
 config HZ_FIXED
 	int
 	default 128 if SOC_AT91RM9200
@@ -1402,7 +1128,7 @@ config THUMB2_KERNEL
 
 config ARM_PATCH_IDIV
 	bool "Runtime patch udiv/sdiv instructions into __aeabi_{u}idiv()"
-	depends on CPU_32v7 && !XIP_KERNEL
+	depends on CPU_32v7
 	default y
 	help
 	  The ARM compiler inserts calls to __aeabi_idiv() and
@@ -1457,13 +1183,13 @@ config OABI_COMPAT
 	  at all). If in doubt say N.
 
 config ARCH_SELECT_MEMORY_MODEL
-	bool
+	def_bool y
 
 config ARCH_FLATMEM_ENABLE
-	bool
+	def_bool !(ARCH_RPC || ARCH_SA1100)
 
 config ARCH_SPARSEMEM_ENABLE
-	bool
+	def_bool !ARCH_FOOTBRIDGE
 	select SPARSEMEM_STATIC if SPARSEMEM
 
 config HIGHMEM
@@ -1487,7 +1213,7 @@ config HIGHMEM
 
 config HIGHPTE
 	bool "Allocate 2nd-level pagetables from highmem" if EXPERT
-	depends on HIGHMEM
+	depends on HIGHMEM && !PREEMPT_RT
 	default y
 	help
 	  The VM uses one page of physical memory for each page table.
@@ -1496,9 +1222,9 @@ config HIGHPTE
 	  consumed by page tables.  Setting this option will allow
 	  user-space 2nd level page tables to reside in high memory.
 
-config CPU_SW_DOMAIN_PAN
-	bool "Enable use of CPU domains to implement privileged no-access"
-	depends on MMU && !ARM_LPAE
+config ARM_PAN
+	bool "Enable privileged no-access"
+	depends on MMU
 	default y
 	help
 	  Increase kernel security by ensuring that normal kernel accesses
@@ -1507,10 +1233,26 @@ config CPU_SW_DOMAIN_PAN
 	  by ensuring that magic values (such as LIST_POISON) will always
 	  fault when dereferenced.
 
+	  The implementation uses CPU domains when !CONFIG_ARM_LPAE and
+	  disabling of TTBR0 page table walks with CONFIG_ARM_LPAE.
+
+config CPU_SW_DOMAIN_PAN
+	def_bool y
+	depends on ARM_PAN && !ARM_LPAE
+	help
+	  Enable use of CPU domains to implement privileged no-access.
+
 	  CPUs with low-vector mappings use a best-efforts implementation.
 	  Their lower 1MB needs to remain accessible for the vectors, but
 	  the remainder of userspace will become appropriately inaccessible.
 
+config CPU_TTBR0_PAN
+	def_bool y
+	depends on ARM_PAN && ARM_LPAE
+	help
+	  Enable privileged no-access by disabling TTBR0 page table walks when
+	  running in kernel mode.
+
 config HW_PERF_EVENTS
 	def_bool y
 	depends on ARM_PMU
@@ -1518,6 +1260,7 @@ config HW_PERF_EVENTS
 config ARM_MODULE_PLTS
 	bool "Use PLTs to allow module memory to spill over into vmalloc area"
 	depends on MODULES
+	select KASAN_VMALLOC if KASAN
 	default y
 	help
 	  Allocate PLTs when loading modules so that jumps and calls whose
@@ -1532,21 +1275,20 @@ config ARM_MODULE_PLTS
 	  Disabling this is usually safe for small single-platform
 	  configurations. If unsure, say y.
 
-config FORCE_MAX_ZONEORDER
-	int "Maximum zone order"
-	default "12" if SOC_AM33XX
-	default "9" if SA1111
-	default "11"
+config ARCH_FORCE_MAX_ORDER
+	int "Order of maximal physically contiguous allocations"
+	default "11" if SOC_AM33XX
+	default "8" if SA1111
+	default "10"
 	help
-	  The kernel memory allocator divides physically contiguous memory
-	  blocks into "zones", where each zone is a power of two number of
-	  pages.  This option selects the largest power of two that the kernel
-	  keeps in the memory allocator.  If you need to allocate very large
-	  blocks of physically contiguous memory, then you may need to
-	  increase this value.
+	  The kernel page allocator limits the size of maximal physically
+	  contiguous allocations. The limit is called MAX_PAGE_ORDER and it
+	  defines the maximal power of two of number of pages that can be
+	  allocated as a single contiguous block. This option allows
+	  overriding the default setting when ability to allocate very
+	  large blocks of physically contiguous memory is required.
 
-	  This config option is actually maximum order plus one. For example,
-	  a value of 11 means that the largest free memory block is 2^10 pages.
+	  Don't change if unsure.
 
 config ALIGNMENT_TRAP
 	def_bool CPU_CP15_MMU
@@ -1618,8 +1360,7 @@ config CC_HAVE_STACKPROTECTOR_TLS
 config STACKPROTECTOR_PER_TASK
 	bool "Use a unique stack canary value for each task"
 	depends on STACKPROTECTOR && CURRENT_POINTER_IN_TPIDRURO && !XIP_DEFLATED_DATA
-	depends on GCC_PLUGINS || CC_HAVE_STACKPROTECTOR_TLS
-	select GCC_PLUGIN_ARM_SSP_PER_TASK if !CC_HAVE_STACKPROTECTOR_TLS
+	depends on CC_HAVE_STACKPROTECTOR_TLS
 	default y
 	help
 	  Due to the fact that GCC uses an ordinary symbol reference from
@@ -1642,15 +1383,17 @@ config USE_OF
 	help
 	  Include support for flattened device tree machine descriptions.
 
+config ARCH_WANT_FLAT_DTB_INSTALL
+	def_bool y
+
 config ATAGS
-	bool "Support for the traditional ATAGS boot data passing" if USE_OF
+	bool "Support for the traditional ATAGS boot data passing"
 	default y
 	help
 	  This is the traditional way of passing data to the kernel at boot
 	  time. If you are solely relying on the flattened device tree (or
 	  the ARM_ATAG_DTB_COMPAT option) then you may unselect this option
-	  to remove ATAGS support from your kernel binary.  If unsure,
-	  leave this to y.
+	  to remove ATAGS support from your kernel binary.
 
 config DEPRECATED_PARAM_STRUCT
 	bool "Provide old way to pass kernel parameters"
@@ -1726,7 +1469,8 @@ config ARM_ATAG_DTB_COMPAT
 	  from the ATAG list and store it at run time into the appended DTB.
 
 choice
-	prompt "Kernel command line type" if ARM_ATAG_DTB_COMPAT
+	prompt "Kernel command line type"
+	depends on ARM_ATAG_DTB_COMPAT
 	default ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER
 
 config ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER
@@ -1755,9 +1499,9 @@ config CMDLINE
 	  memory size and the root device (e.g., mem=64M root=/dev/nfs).
 
 choice
-	prompt "Kernel command line type" if CMDLINE != ""
+	prompt "Kernel command line type"
+	depends on CMDLINE != ""
 	default CMDLINE_FROM_BOOTLOADER
-	depends on ATAGS
 
 config CMDLINE_FROM_BOOTLOADER
 	bool "Use bootloader kernel arguments if available"
@@ -1784,6 +1528,7 @@ endchoice
 config XIP_KERNEL
 	bool "Kernel Execute-In-Place from ROM"
 	depends on !ARM_LPAE && !ARCH_MULTIPLATFORM
+	depends on !ARM_PATCH_IDIV && !ARM_PATCH_PHYS_VIRT && !SMP_ON_UP
 	help
 	  Execute-In-Place allows the kernel to run from non-volatile storage
 	  directly addressable by the CPU, such as NOR flash. This saves RAM
@@ -1822,20 +1567,8 @@ config XIP_DEFLATED_DATA
 	  copied, saving some precious ROM space. A possible drawback is a
 	  slightly longer boot delay.
 
-config KEXEC
-	bool "Kexec system call (EXPERIMENTAL)"
-	depends on (!SMP || PM_SLEEP_SMP)
-	depends on MMU
-	select KEXEC_CORE
-	help
-	  kexec is a system call that implements the ability to shutdown your
-	  current kernel, and to start another kernel.  It is like a reboot
-	  but it is independent of the system firmware.   And like a reboot
-	  you can start any kernel with it, not just Linux.
-
-	  It is an ongoing process to be certain the hardware in a machine
-	  is properly shutdown, so do not be surprised if this code does not
-	  initially work for you.
+config ARCH_SUPPORTS_KEXEC
+	def_bool (!SMP || PM_SLEEP_SMP) && MMU
 
 config ATAGS_PROC
 	bool "Export atags in procfs"
@@ -1845,20 +1578,15 @@ config ATAGS_PROC
 	  Should the atags used to boot the kernel be exported in an "atags"
 	  file in procfs. Useful with kexec.
 
-config CRASH_DUMP
-	bool "Build kdump crash kernel (EXPERIMENTAL)"
-	help
-	  Generate crash dump after being started by kexec. This should
-	  be normally only set in special crash dump kernels which are
-	  loaded in the main kernel with kexec-tools into a specially
-	  reserved region and then later executed after a crash by
-	  kdump/kexec. The crash dump kernel must be compiled to a
-	  memory address not used by the main kernel
+config ARCH_SUPPORTS_CRASH_DUMP
+	def_bool y
 
-	  For more details see Documentation/admin-guide/kdump/kdump.rst
+config ARCH_DEFAULT_CRASH_DUMP
+	def_bool y
 
 config AUTO_ZRELADDR
-	bool "Auto calculation of the decompressed kernel image address"
+	bool "Auto calculation of the decompressed kernel image address" if !ARCH_MULTIPLATFORM
+	default !(ARCH_FOOTBRIDGE || ARCH_RPC || ARCH_SA1100)
 	help
 	  ZRELADDR is the physical address where the decompressed kernel
 	  image will be placed. If AUTO_ZRELADDR is selected, the address
@@ -1962,7 +1690,7 @@ config VFP
 	  Say Y to include VFP support code in the kernel. This is needed
 	  if your hardware includes a VFP unit.
 
-	  Please see <file:Documentation/arm/vfp/release-notes.rst> for
+	  Please see <file:Documentation/arch/arm/vfp/release-notes.rst> for
 	  release notes and additional status information.
 
 	  Say N if your target does not have VFP hardware.
@@ -2006,9 +1734,3 @@ config ARCH_HIBERNATION_POSSIBLE
 	default y if ARCH_SUSPEND_POSSIBLE
 
 endmenu
-
-if CRYPTO
-source "arch/arm/crypto/Kconfig"
-endif
-
-source "arch/arm/Kconfig.assembler"
diff --git a/arch/arm/Kconfig.assembler b/arch/arm/Kconfig.assembler
deleted file mode 100644
index 5cb31aae1188..000000000000
--- a/arch/arm/Kconfig.assembler
+++ /dev/null
@@ -1,6 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0
-
-config AS_VFP_VMRS_FPINST
-	def_bool $(as-instr,.fpu vfpv2\nvmrs r0$(comma)FPINST)
-	help
-	  Supported by binutils >= 2.24 and LLVM integrated assembler.
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index 0c9497d549e3..366f162e147d 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -17,7 +17,7 @@ config ARM_PTDUMP_DEBUGFS
 	  kernel.
 	  If in doubt, say "N"
 
-config DEBUG_WX
+config ARM_DEBUG_WX
 	bool "Warn on W+X mappings at boot"
 	depends on MMU
 	select ARM_PTDUMP_CORE
@@ -90,9 +90,6 @@ config BACKTRACE_VERBOSE
 	  In most cases, say N here, unless you are intending to debug the
 	  kernel and have access to the kernel binary image.
 
-config FRAME_POINTER
-	bool
-
 config DEBUG_USER
 	bool "Verbose user fault messages"
 	help
@@ -210,6 +207,26 @@ choice
 		  Say Y here if you want kernel low-level debugging support
 		  on the FLEXCOM3 port of SAMA7G5.
 
+	config DEBUG_AT91_LAN966_FLEXCOM
+		bool "Kernel low-level debugging on LAN966 FLEXCOM USART"
+		select DEBUG_AT91_UART
+		depends on SOC_LAN966
+		help
+		Say Y here if you want kernel low-level debugging support
+		on the FLEXCOM port of LAN966.
+
+		DEBUG_UART_PHYS | DEBUG_UART_VIRT
+
+		0xe0040200      | 0xfd040200     | FLEXCOM0
+		0xe0044200      | 0xfd044200     | FLEXCOM1
+		0xe0060200      | 0xfd060200     | FLEXCOM2
+		0xe0064200      | 0xfd064200     | FLEXCOM3
+		0xe0070200      | 0xfd070200     | FLEXCOM4
+
+		By default, enabling FLEXCOM3 port. Based on requirement, use
+		DEBUG_UART_PHYS and DEBUG_UART_VIRT configurations from above
+		table.
+
 	config DEBUG_BCM2835
 		bool "Kernel low-level debugging on BCM2835 PL011 UART"
 		depends on ARCH_BCM2835 && ARCH_MULTI_V6
@@ -225,6 +242,10 @@ choice
 		depends on ARCH_BCM_5301X || ARCH_BCM_NSP
 		select DEBUG_UART_8250
 
+	config DEBUG_BCMBCA
+		bool "Kernel low-level debugging on BCMBCA UART0"
+		depends on ARCH_BCMBCA
+
 	config DEBUG_BCM_HR2
 		bool "Kernel low-level debugging on Hurricane 2 UART2"
 		depends on ARCH_BCM_HR2
@@ -251,7 +272,7 @@ choice
 
 	config DEBUG_BCM63XX_UART
 		bool "Kernel low-level debugging on BCM63XX UART"
-		depends on ARCH_BCM_63XX
+		depends on ARCH_BCMBCA
 
 	config DEBUG_BERLIN_UART
 		bool "Marvell Berlin SoC Debug UART"
@@ -287,14 +308,6 @@ choice
 		  Say Y here if you want the debug print routines to direct
 		  their output to the second serial port on these devices.
 
-	config DEBUG_CNS3XXX
-		bool "Kernel Kernel low-level debugging on Cavium Networks CNS3xxx"
-		depends on ARCH_CNS3XXX
-		select DEBUG_UART_8250
-		help
-		  Say Y here if you want the debug print routines to direct
-                  their output to the CNS3xxx UART0.
-
 	config DEBUG_DAVINCI_DA8XX_UART1
 		bool "Kernel low-level debugging on DaVinci DA8XX using UART1"
 		depends on ARCH_DAVINCI_DA8XX
@@ -311,14 +324,6 @@ choice
 		  Say Y here if you want the debug print routines to direct
 		  their output to UART2 serial port on DaVinci DA8XX devices.
 
-	config DEBUG_DAVINCI_DMx_UART0
-		bool "Kernel low-level debugging on DaVinci DMx using UART0"
-		depends on ARCH_DAVINCI_DMx
-		select DEBUG_UART_8250
-		help
-		  Say Y here if you want the debug print routines to direct
-		  their output to UART0 serial port on DaVinci DMx devices.
-
 	config DEBUG_DC21285_PORT
 		bool "Kernel low-level debugging messages via footbridge serial port"
 		depends on FOOTBRIDGE
@@ -748,30 +753,6 @@ choice
 		depends on ARCH_OMAP2PLUS
 		select DEBUG_UART_8250
 
-	config DEBUG_OMAP7XXUART1
-		bool "Kernel low-level debugging via OMAP730 UART1"
-		depends on ARCH_OMAP730
-		select DEBUG_UART_8250
-		help
-		  Say Y here if you want kernel low-level debugging support
-		  on OMAP730 based platforms on the UART1.
-
-	config DEBUG_OMAP7XXUART2
-		bool "Kernel low-level debugging via OMAP730 UART2"
-		depends on ARCH_OMAP730
-		select DEBUG_UART_8250
-		help
-		  Say Y here if you want kernel low-level debugging support
-		  on OMAP730 based platforms on the UART2.
-
-	config DEBUG_OMAP7XXUART3
-		bool "Kernel low-level debugging via OMAP730 UART3"
-		depends on ARCH_OMAP730
-		select DEBUG_UART_8250
-		help
-		  Say Y here if you want kernel low-level debugging support
-		  on OMAP730 based platforms on the UART3.
-
 	config DEBUG_TI81XXUART1
 		bool "Kernel low-level debugging messages via TI81XX UART1 (ti8148evm)"
 		depends on ARCH_OMAP2PLUS
@@ -1026,7 +1007,6 @@ choice
 	config DEBUG_S3C_UART0
 		depends on PLAT_SAMSUNG || ARCH_S5PV210 || ARCH_EXYNOS
 		select DEBUG_EXYNOS_UART if ARCH_EXYNOS
-		select DEBUG_S3C24XX_UART if ARCH_S3C24XX
 		select DEBUG_S3C64XX_UART if ARCH_S3C64XX
 		select DEBUG_S5PV210_UART if ARCH_S5PV210
 		bool "Use Samsung S3C UART 0 for low-level debug"
@@ -1038,7 +1018,6 @@ choice
 	config DEBUG_S3C_UART1
 		depends on PLAT_SAMSUNG || ARCH_S5PV210 || ARCH_EXYNOS
 		select DEBUG_EXYNOS_UART if ARCH_EXYNOS
-		select DEBUG_S3C24XX_UART if ARCH_S3C24XX
 		select DEBUG_S3C64XX_UART if ARCH_S3C64XX
 		select DEBUG_S5PV210_UART if ARCH_S5PV210
 		bool "Use Samsung S3C UART 1 for low-level debug"
@@ -1050,7 +1029,6 @@ choice
 	config DEBUG_S3C_UART2
 		depends on PLAT_SAMSUNG || ARCH_S5PV210 || ARCH_EXYNOS
 		select DEBUG_EXYNOS_UART if ARCH_EXYNOS
-		select DEBUG_S3C24XX_UART if ARCH_S3C24XX
 		select DEBUG_S3C64XX_UART if ARCH_S3C64XX
 		select DEBUG_S5PV210_UART if ARCH_S5PV210
 		bool "Use Samsung S3C UART 2 for low-level debug"
@@ -1070,33 +1048,6 @@ choice
 		  their output to UART 3. The port must have been initialised
 		  by the boot-loader before use.
 
-	config DEBUG_S3C2410_UART0
-		depends on ARCH_S3C24XX
-		select DEBUG_S3C2410_UART
-		bool "Use S3C2410/S3C2412 UART 0 for low-level debug"
-		help
-		  Say Y here if you want the debug print routines to direct
-		  their output to UART 0. The port must have been initialised
-		  by the boot-loader before use.
-
-	config DEBUG_S3C2410_UART1
-		depends on ARCH_S3C24XX
-		select DEBUG_S3C2410_UART
-		bool "Use S3C2410/S3C2412 UART 1 for low-level debug"
-		help
-		  Say Y here if you want the debug print routines to direct
-		  their output to UART 1. The port must have been initialised
-		  by the boot-loader before use.
-
-	config DEBUG_S3C2410_UART2
-		depends on ARCH_S3C24XX
-		select DEBUG_S3C2410_UART
-		bool "Use S3C2410/S3C2412 UART 2 for low-level debug"
-		help
-		  Say Y here if you want the debug print routines to direct
-		  their output to UART 2. The port must have been initialised
-		  by the boot-loader before use.
-
 	config DEBUG_SA1100
 		depends on ARCH_SA1100
 		bool "Use SA1100 UARTs for low-level debug"
@@ -1256,8 +1207,8 @@ choice
 		depends on MACH_STM32MP157
 		select DEBUG_STM32_UART
 		help
-		  Say Y here if you want kernel low-level debugging support
-		  on STM32MP1 based platforms, wich default UART is wired on
+		  Say Y here if you want kernel low-level debugging support on
+		  STM32MP1-based platforms, where the default UART is wired to
 		  UART4, but another UART instance can be selected by modifying
 		  CONFIG_DEBUG_UART_PHYS and CONFIG_DEBUG_UART_VIRT.
 
@@ -1459,13 +1410,6 @@ config DEBUG_AT91_UART
 config DEBUG_EXYNOS_UART
 	bool
 
-config DEBUG_S3C2410_UART
-	bool
-	select DEBUG_S3C24XX_UART
-
-config DEBUG_S3C24XX_UART
-	bool
-
 config DEBUG_S3C64XX_UART
 	bool
 
@@ -1473,8 +1417,7 @@ config DEBUG_S5PV210_UART
 	bool
 
 config DEBUG_S3C_UART
-	depends on DEBUG_S3C2410_UART || DEBUG_S3C24XX_UART || \
-		   DEBUG_S3C64XX_UART ||  DEBUG_S5PV210_UART || \
+	depends on DEBUG_S3C64XX_UART ||  DEBUG_S5PV210_UART || \
 		   DEBUG_EXYNOS_UART
 	int
 	default "0" if DEBUG_S3C_UART0
@@ -1575,7 +1518,7 @@ config DEBUG_LL_INCLUDE
 	default "debug/renesas-scif.S" if DEBUG_RMOBILE_SCIFA0
 	default "debug/renesas-scif.S" if DEBUG_RMOBILE_SCIFA1
 	default "debug/renesas-scif.S" if DEBUG_RMOBILE_SCIFA4
-	default "debug/s3c24xx.S" if DEBUG_S3C24XX_UART || DEBUG_S3C64XX_UART
+	default "debug/s3c24xx.S" if DEBUG_S3C64XX_UART
 	default "debug/s5pv210.S" if DEBUG_S5PV210_UART
 	default "debug/sti.S" if DEBUG_STIH41X_ASC2
 	default "debug/sti.S" if DEBUG_STIH41X_SBC_ASC1
@@ -1587,7 +1530,7 @@ config DEBUG_LL_INCLUDE
 	default "debug/vf.S" if DEBUG_VF_UART
 	default "debug/vt8500.S" if DEBUG_VT8500_UART0
 	default "debug/zynq.S" if DEBUG_ZYNQ_UART0 || DEBUG_ZYNQ_UART1
-	default "debug/bcm63xx.S" if DEBUG_BCM63XX_UART
+	default "debug/bcm63xx.S" if DEBUG_BCM63XX_UART || DEBUG_BCMBCA
 	default "debug/digicolor.S" if DEBUG_DIGICOLOR_UA0
 	default "debug/brcmstb.S" if DEBUG_BRCMSTB_UART
 	default "mach/debug-macro.S"
@@ -1598,11 +1541,10 @@ config DEBUG_UART_PL01X
 
 # Compatibility options for 8250
 config DEBUG_UART_8250
-	def_bool ARCH_IOP32X || ARCH_IXP4XX || ARCH_RPC
+	def_bool ARCH_IXP4XX || ARCH_RPC
 
 config DEBUG_UART_PHYS
 	hex "Physical base address of debug UART"
-	default 0x01c20000 if DEBUG_DAVINCI_DMx_UART0
 	default 0x01c28000 if DEBUG_SUNXI_UART0
 	default 0x01c28400 if DEBUG_SUNXI_UART1
 	default 0x01d0c000 if DEBUG_DAVINCI_DA8XX_UART1
@@ -1652,20 +1594,11 @@ config DEBUG_UART_PHYS
 	default 0x48020000 if DEBUG_OMAP4UART3 || DEBUG_TI81XXUART1
 	default 0x48022000 if DEBUG_TI81XXUART2
 	default 0x48024000 if DEBUG_TI81XXUART3
-	default 0x4806a000 if DEBUG_OMAP2UART1 || DEBUG_OMAP3UART1 || \
-				DEBUG_OMAP4UART1 || DEBUG_OMAP5UART1
-	default 0x4806c000 if DEBUG_OMAP2UART2 || DEBUG_OMAP3UART2 || \
-				DEBUG_OMAP4UART2 || DEBUG_OMAP5UART2
+	default 0x4806a000 if DEBUG_OMAP2UART1
+	default 0x4806c000 if DEBUG_OMAP2UART2
 	default 0x4806e000 if DEBUG_OMAP2UART3 || DEBUG_OMAP4UART4
 	default 0x49020000 if DEBUG_OMAP3UART3
 	default 0x49042000 if DEBUG_OMAP3UART4
-	default 0x50000000 if DEBUG_S3C24XX_UART && (DEBUG_S3C_UART0 || \
-				DEBUG_S3C2410_UART0)
-	default 0x50004000 if DEBUG_S3C24XX_UART && (DEBUG_S3C_UART1 || \
-				DEBUG_S3C2410_UART1)
-	default 0x50008000 if DEBUG_S3C24XX_UART && (DEBUG_S3C_UART2 || \
-				DEBUG_S3C2410_UART2)
-	default 0x78000000 if DEBUG_CNS3XXX
 	default 0x7c0003f8 if DEBUG_FOOTBRIDGE_COM1
 	default 0x7f005000 if DEBUG_S3C64XX_UART && DEBUG_S3C_UART0
 	default 0x7f005400 if DEBUG_S3C64XX_UART && DEBUG_S3C_UART1
@@ -1685,6 +1618,7 @@ config DEBUG_UART_PHYS
 	default 0xd4017000 if DEBUG_MMP_UART2
 	default 0xd4018000 if DEBUG_MMP_UART3
 	default 0xe0000000 if DEBUG_SPEAR13XX
+	default 0xe0064200 if DEBUG_AT91_LAN966_FLEXCOM
 	default 0xe1824200 if DEBUG_AT91_SAMA7G5_FLEXCOM3
 	default 0xe4007000 if DEBUG_HIP04_UART
 	default 0xe6c40000 if DEBUG_RMOBILE_SCIFA0
@@ -1708,18 +1642,18 @@ config DEBUG_UART_PHYS
 	default 0xfcb00000 if DEBUG_HI3620_UART
 	default 0xfd883000 if DEBUG_ALPINE_UART0
 	default 0xfe531000 if DEBUG_STIH41X_SBC_ASC1
-	default 0xfe800000 if ARCH_IOP32X
 	default 0xfed32000 if DEBUG_STIH41X_ASC2
 	default 0xff690000 if DEBUG_RK32_UART2
+	default 0xff800640 if DEBUG_BCMBCA
 	default 0xffc02000 if DEBUG_SOCFPGA_UART0
 	default 0xffc02100 if DEBUG_SOCFPGA_ARRIA10_UART1
 	default 0xffc03000 if DEBUG_SOCFPGA_CYCLONE5_UART1
 	default 0xffe40000 if DEBUG_RCAR_GEN1_SCIF0
 	default 0xffe42000 if DEBUG_RCAR_GEN1_SCIF2
 	default 0xfff36000 if DEBUG_HIGHBANK_UART
-	default 0xfffb0000 if DEBUG_OMAP1UART1 || DEBUG_OMAP7XXUART1
-	default 0xfffb0800 if DEBUG_OMAP1UART2 || DEBUG_OMAP7XXUART2
-	default 0xfffb9800 if DEBUG_OMAP1UART3 || DEBUG_OMAP7XXUART3
+	default 0xfffb0000 if DEBUG_OMAP1UART1
+	default 0xfffb0800 if DEBUG_OMAP1UART2
+	default 0xfffb9800 if DEBUG_OMAP1UART3
 	default 0xfffe8600 if DEBUG_BCM63XX_UART
 	default 0xffffee00 if DEBUG_AT91_SAM9263_DBGU
 	default 0xfffff200 if DEBUG_AT91_RM9200_DBGU
@@ -1733,9 +1667,9 @@ config DEBUG_UART_PHYS
 		DEBUG_RCAR_GEN2_SCIF2 || DEBUG_RCAR_GEN2_SCIF4 || \
 		DEBUG_RCAR_GEN2_SCIFA2 || \
 		DEBUG_RMOBILE_SCIFA0 || DEBUG_RMOBILE_SCIFA1 || \
-		DEBUG_RMOBILE_SCIFA4 || DEBUG_S3C24XX_UART || \
+		DEBUG_RMOBILE_SCIFA4 || \
 		DEBUG_S3C64XX_UART || \
-		DEBUG_BCM63XX_UART || DEBUG_ASM9260_UART || \
+		DEBUG_BCM63XX_UART || DEBUG_BCMBCA || DEBUG_ASM9260_UART || \
 		DEBUG_DIGICOLOR_UA0 || \
 		DEBUG_AT91_UART || DEBUG_STM32_UART || \
 		DEBUG_STIH41X_ASC2 || DEBUG_STIH41X_SBC_ASC1 || \
@@ -1770,15 +1704,9 @@ config DEBUG_UART_VIRT
 	default 0xf6200000 if DEBUG_PXA_UART1
 	default 0xf7000000 if DEBUG_SUN9I_UART0
 	default 0xf7000000 if DEBUG_S3C64XX_UART && DEBUG_S3C_UART0
-	default 0xf7000000 if DEBUG_S3C24XX_UART && (DEBUG_S3C_UART0 || \
-				DEBUG_S3C2410_UART0)
 	default 0xf7000400 if DEBUG_S3C64XX_UART && DEBUG_S3C_UART1
 	default 0xf7000800 if DEBUG_S3C64XX_UART && DEBUG_S3C_UART2
 	default 0xf7000c00 if DEBUG_S3C64XX_UART && DEBUG_S3C_UART3
-	default 0xf7004000 if DEBUG_S3C24XX_UART && (DEBUG_S3C_UART1 || \
-				DEBUG_S3C2410_UART1)
-	default 0xf7008000 if DEBUG_S3C24XX_UART && (DEBUG_S3C_UART2 || \
-				DEBUG_S3C2410_UART2)
 	default 0xf7020000 if DEBUG_AT91_SAMA5D2_UART1
 	default 0xf7fc9000 if DEBUG_BERLIN_UART
 	default 0xf8007000 if DEBUG_HIP04_UART
@@ -1791,13 +1719,10 @@ config DEBUG_UART_VIRT
 	default 0xfa020000 if DEBUG_OMAP4UART3 || DEBUG_TI81XXUART1
 	default 0xfa022000 if DEBUG_TI81XXUART2
 	default 0xfa024000 if DEBUG_TI81XXUART3
-	default 0xfa06a000 if DEBUG_OMAP2UART1 || DEBUG_OMAP3UART1 || \
-				DEBUG_OMAP4UART1 || DEBUG_OMAP5UART1
-	default 0xfa06c000 if DEBUG_OMAP2UART2 || DEBUG_OMAP3UART2 || \
-				DEBUG_OMAP4UART2 || DEBUG_OMAP5UART2
+	default 0xfa06a000 if DEBUG_OMAP2UART1
+	default 0xfa06c000 if DEBUG_OMAP2UART2
 	default 0xfa06e000 if DEBUG_OMAP2UART3 || DEBUG_OMAP4UART4
 	default 0xfa71e000 if DEBUG_QCOM_UARTDM
-	default 0xfb002000 if DEBUG_CNS3XXX
 	default 0xfb009000 if DEBUG_REALVIEW_STD_PORT
 	default 0xfb00c000 if DEBUG_AT91_SAMA5D4_USART3
 	default 0xfb020000 if DEBUG_OMAP3UART3
@@ -1805,6 +1730,7 @@ config DEBUG_UART_VIRT
 	default 0xfb10c000 if DEBUG_REALVIEW_PB1176_PORT
 	default 0xfcfe8600 if DEBUG_BCM63XX_UART
 	default 0xfd000000 if DEBUG_SPEAR3XX || DEBUG_SPEAR13XX
+	default 0xfd064200 if DEBUG_AT91_LAN966_FLEXCOM
 	default 0xfd531000 if DEBUG_STIH41X_SBC_ASC1
 	default 0xfd883000 if DEBUG_ALPINE_UART0
 	default 0xfdd32000 if DEBUG_STIH41X_ASC2
@@ -1813,7 +1739,7 @@ config DEBUG_UART_VIRT
 	default 0xfe018000 if DEBUG_MMP_UART3
 	default 0xfe100000 if DEBUG_IMX23_UART || DEBUG_IMX28_UART
 	default 0xfe300000 if DEBUG_BCM_KONA_UART
-	default 0xfe800000 if ARCH_IOP32X
+	default 0xfe300640 if DEBUG_BCMBCA
 	default 0xfeb00000 if DEBUG_HI3620_UART || DEBUG_HIX5HD2_UART
 	default 0xfeb24000 if DEBUG_RK3X_UART0
 	default 0xfeb26000 if DEBUG_RK3X_UART1
@@ -1824,7 +1750,6 @@ config DEBUG_UART_VIRT
 	default 0xfec03000 if DEBUG_SOCFPGA_CYCLONE5_UART1
 	default 0xfec12000 if DEBUG_MVEBU_UART0 || DEBUG_MVEBU_UART0_ALTERNATE
 	default 0xfec12100 if DEBUG_MVEBU_UART1_ALTERNATE
-	default 0xfec20000 if DEBUG_DAVINCI_DMx_UART0
 	default 0xfec90000 if DEBUG_RK32_UART2
 	default 0xfed0c000 if DEBUG_DAVINCI_DA8XX_UART1
 	default 0xfed0d000 if DEBUG_DAVINCI_DA8XX_UART2 || DEBUG_SD5203_UART
@@ -1837,16 +1762,16 @@ config DEBUG_UART_VIRT
 	default 0xfec00000 if ARCH_IXP4XX && !CPU_BIG_ENDIAN
 	default 0xfec00003 if ARCH_IXP4XX && CPU_BIG_ENDIAN
 	default 0xfef36000 if DEBUG_HIGHBANK_UART
-	default 0xfefb0000 if DEBUG_OMAP1UART1 || DEBUG_OMAP7XXUART1
-	default 0xfefb0800 if DEBUG_OMAP1UART2 || DEBUG_OMAP7XXUART2
-	default 0xfefb9800 if DEBUG_OMAP1UART3 || DEBUG_OMAP7XXUART3
+	default 0xff0b0000 if DEBUG_OMAP1UART1
+	default 0xff0b0800 if DEBUG_OMAP1UART2
+	default 0xff0b9800 if DEBUG_OMAP1UART3
 	default 0xffd01000 if DEBUG_HIP01_UART
 	default DEBUG_UART_PHYS if !MMU
 	depends on DEBUG_LL_UART_8250 || DEBUG_LL_UART_PL01X || \
 		DEBUG_UART_8250 || DEBUG_UART_PL01X || DEBUG_MESON_UARTAO || \
-		DEBUG_QCOM_UARTDM || DEBUG_S3C24XX_UART || \
+		DEBUG_QCOM_UARTDM || \
 		DEBUG_S3C64XX_UART || \
-		DEBUG_BCM63XX_UART || DEBUG_ASM9260_UART || \
+		DEBUG_BCM63XX_UART || DEBUG_BCMBCA || DEBUG_ASM9260_UART || \
 		DEBUG_DIGICOLOR_UA0 || \
 		DEBUG_AT91_UART || DEBUG_STM32_UART || \
 		DEBUG_STIH41X_ASC2 || DEBUG_STIH41X_SBC_ASC1 || \
@@ -1855,9 +1780,8 @@ config DEBUG_UART_VIRT
 config DEBUG_UART_8250_SHIFT
 	int "Register offset shift for the 8250 debug UART"
 	depends on DEBUG_LL_UART_8250 || DEBUG_UART_8250
-	default 0 if DEBUG_FOOTBRIDGE_COM1 || ARCH_IOP32X || DEBUG_BCM_5301X || \
-		DEBUG_BCM_HR2 || DEBUG_OMAP7XXUART1 || DEBUG_OMAP7XXUART2 || \
-		DEBUG_OMAP7XXUART3
+	default 0 if DEBUG_FOOTBRIDGE_COM1 || DEBUG_BCM_5301X || \
+		DEBUG_BCM_HR2
 	default 3 if DEBUG_MSTARV7_PMUART
 	default 2
 
@@ -1868,9 +1792,9 @@ config DEBUG_UART_8250_WORD
 	default y if DEBUG_SOCFPGA_UART0 || DEBUG_SOCFPGA_ARRIA10_UART1 || \
 		DEBUG_SOCFPGA_CYCLONE5_UART1 || DEBUG_KEYSTONE_UART0 || \
 		DEBUG_KEYSTONE_UART1 || DEBUG_ALPINE_UART0 || \
-		DEBUG_DAVINCI_DMx_UART0 || DEBUG_DAVINCI_DA8XX_UART1 || \
-		DEBUG_DAVINCI_DA8XX_UART2 || DEBUG_BCM_IPROC_UART3 || \
-		DEBUG_BCM_KONA_UART || DEBUG_RK32_UART2
+		DEBUG_DAVINCI_DA8XX_UART1 || DEBUG_DAVINCI_DA8XX_UART2 || \
+		DEBUG_BCM_IPROC_UART3 || DEBUG_BCM_KONA_UART || \
+		DEBUG_RK32_UART2
 
 config DEBUG_UART_8250_PALMCHIP
 	bool "8250 UART is Palmchip BK-310x"
@@ -1882,26 +1806,19 @@ config DEBUG_UART_8250_PALMCHIP
 
 config DEBUG_UNCOMPRESS
 	bool "Enable decompressor debugging via DEBUG_LL output"
-	depends on ARCH_MULTIPLATFORM || PLAT_SAMSUNG || ARM_SINGLE_ARMV7M
+	depends on !ARCH_MULTIPLATFORM
+	depends on !(ARCH_FOOTBRIDGE || ARCH_RPC || ARCH_SA1100)
 	depends on DEBUG_LL && !DEBUG_OMAP2PLUS_UART && \
 		     (!DEBUG_TEGRA_UART || !ZBOOT_ROM) && \
 		     !DEBUG_BRCMSTB_UART && !DEBUG_SEMIHOSTING
 	help
-	  This option influences the normal decompressor output for
-	  multiplatform kernels.  Normally, multiplatform kernels disable
-	  decompressor output because it is not possible to know where to
-	  send the decompressor output.
-
-	  When this option is set, the selected DEBUG_LL output method
-	  will be re-used for normal decompressor output on multiplatform
-	  kernels.
-	  
+	  Say Y here to enable debug output in the decompressor code, using
+	  the selected DEBUG_LL output method.
 
 config UNCOMPRESS_INCLUDE
 	string
-	default "debug/uncompress.h" if ARCH_MULTIPLATFORM || ARCH_MSM || \
-					PLAT_SAMSUNG || ARM_SINGLE_ARMV7M
-	default "mach/uncompress.h"
+	default "mach/uncompress.h" if ARCH_FOOTBRIDGE || ARCH_RPC || ARCH_SA1100
+	default "debug/uncompress.h"
 
 config EARLY_PRINTK
 	bool "Early printk"
diff --git a/arch/arm/Kconfig.platforms b/arch/arm/Kconfig.platforms
new file mode 100644
index 000000000000..5c19c1f2cff6
--- /dev/null
+++ b/arch/arm/Kconfig.platforms
@@ -0,0 +1,208 @@
+# SPDX-License-Identifier: GPL-2.0-only
+
+menu "Platform selection"
+	depends on MMU
+
+comment "CPU Core family selection"
+
+config ARCH_MULTI_V4
+	bool "ARMv4 based platforms (FA526, StrongARM)"
+	depends on !ARCH_MULTI_V6_V7
+	# https://github.com/llvm/llvm-project/issues/50764
+	depends on !LD_IS_LLD || LLD_VERSION >= 160000
+	select ARCH_MULTI_V4_V5
+	select CPU_FA526 if !(CPU_SA110 || CPU_SA1100)
+
+config ARCH_MULTI_V4T
+	bool "ARMv4T based platforms (ARM720T, ARM920T, ...)"
+	depends on !ARCH_MULTI_V6_V7
+	# https://github.com/llvm/llvm-project/issues/50764
+	depends on !LD_IS_LLD || LLD_VERSION >= 160000
+	select ARCH_MULTI_V4_V5
+	select CPU_ARM920T if !(CPU_ARM7TDMI || CPU_ARM720T || \
+		CPU_ARM740T || CPU_ARM9TDMI || CPU_ARM922T || \
+		CPU_ARM925T || CPU_ARM940T)
+
+config ARCH_MULTI_V5
+	bool "ARMv5 based platforms (ARM926T, XSCALE, PJ1, ...)"
+	depends on !ARCH_MULTI_V6_V7
+	select ARCH_MULTI_V4_V5
+	select CPU_ARM926T if !(CPU_ARM946E || CPU_ARM1020 || \
+		CPU_ARM1020E || CPU_ARM1022 || CPU_ARM1026 || \
+		CPU_XSCALE || CPU_XSC3 || CPU_MOHAWK || CPU_FEROCEON)
+
+config ARCH_MULTI_V4_V5
+	bool
+
+config ARCH_MULTI_V6
+	bool "ARMv6 based platforms (ARM11)"
+	select ARCH_MULTI_V6_V7
+	select CPU_V6K
+
+config ARCH_MULTI_V7
+	bool "ARMv7 based platforms (Cortex-A, PJ4, Scorpion, Krait)"
+	default y
+	select ARCH_MULTI_V6_V7
+	select CPU_V7
+	select HAVE_SMP
+
+config ARCH_MULTI_V6_V7
+	bool
+	select MIGHT_HAVE_CACHE_L2X0
+
+config ARCH_MULTI_CPU_AUTO
+	def_bool !(ARCH_MULTI_V4 || ARCH_MULTI_V4T || ARCH_MULTI_V6_V7)
+	select ARCH_MULTI_V5
+
+endmenu
+
+config ARCH_VIRT
+	bool "Dummy Virtual Machine"
+	depends on ARCH_MULTI_V7
+	select ARM_AMBA
+	select ARM_GIC
+	select ARM_GIC_V2M if PCI
+	select ARM_GIC_V3
+	select ARM_GIC_V3_ITS if PCI
+	select ARM_PSCI
+	select HAVE_ARM_ARCH_TIMER
+
+config ARCH_AIROHA
+	bool "Airoha SoC Support"
+	depends on ARCH_MULTI_V7
+	select ARM_AMBA
+	select ARM_GIC
+	select ARM_GIC_V3
+	select ARM_PSCI
+	select HAVE_ARM_ARCH_TIMER
+	help
+	  Support for Airoha EN7523 SoCs
+
+config MACH_ASM9260
+	bool "Alphascale ASM9260"
+	depends on ARCH_MULTI_V5
+	depends on CPU_LITTLE_ENDIAN
+	select CPU_ARM926T
+	select ASM9260_TIMER
+	help
+	  Support for Alphascale ASM9260 based platform.
+
+menuconfig ARCH_HPE
+	bool "HPE SoC support"
+	depends on ARCH_MULTI_V7
+	help
+	  This enables support for HPE ARM based BMC chips.
+
+if ARCH_HPE
+
+config ARCH_HPE_GXP
+	bool "HPE GXP SoC"
+	depends on ARCH_MULTI_V7
+	select ARM_VIC
+	select GENERIC_IRQ_CHIP
+	select CLKSRC_MMIO
+	help
+	  HPE GXP is the name of the HPE Soc. This SoC is used to implement many
+	  BMC features at HPE. It supports ARMv7 architecture based on the Cortex
+	  A9 core. It is capable of using an AXI bus to which a memory controller
+	  is attached. It has multiple SPI interfaces to connect boot flash and
+	  BIOS flash. It uses a 10/100/1000 MAC for network connectivity. It
+	  has multiple i2c engines to drive connectivity with a host
+	  infrastructure.
+
+endif
+
+menuconfig ARCH_MOXART
+	bool "MOXA ART SoC"
+	depends on ARCH_MULTI_V4
+	depends on CPU_LITTLE_ENDIAN
+	select CPU_FA526
+	select ARM_DMA_MEM_BUFFERABLE
+	select FARADAY_FTINTC010
+	select FTTMR010_TIMER
+	select GPIOLIB
+	select PHYLIB if NETDEVICES
+	help
+	  Say Y here if you want to run your kernel on hardware with a
+	  MOXA ART SoC.
+	  The MOXA ART SoC is based on a Faraday FA526 ARMv4 32-bit
+	  192 MHz CPU with MMU and 16KB/8KB D/I-cache (UC-7112-LX).
+	  Used on models UC-7101, UC-7112/UC-7110, IA240/IA241, IA3341.
+
+if ARCH_MOXART
+
+config MACH_UC7112LX
+	bool "MOXA UC-7112-LX"
+	depends on ARCH_MOXART
+	help
+	  Say Y here if you intend to run this kernel on a MOXA
+	  UC-7112-LX embedded computer.
+
+endif
+
+config ARCH_NSPIRE
+	bool "TI-NSPIRE based"
+	depends on ARCH_MULTI_V4T
+	depends on CPU_LITTLE_ENDIAN
+	select CPU_ARM926T
+	select GENERIC_IRQ_CHIP
+	select ARM_AMBA
+	select ARM_VIC
+	select ARM_TIMER_SP804
+	select NSPIRE_TIMER
+	select POWER_RESET
+	select POWER_RESET_SYSCON
+	help
+	  This enables support for systems using the TI-NSPIRE CPU
+
+config ARCH_RDA
+	bool "RDA Micro SoCs"
+	depends on ARCH_MULTI_V7
+	select RDA_INTC
+	select RDA_TIMER
+	help
+	  This enables support for the RDA Micro 8810PL SoC family.
+
+menuconfig ARCH_SUNPLUS
+	bool "Sunplus SoCs"
+	depends on ARCH_MULTI_V7
+	help
+	  Support for Sunplus SoC family: SP7021 and succeeding SoC-based systems,
+	  such as the Banana Pi BPI-F2S development board (and derivatives).
+	  (<http://www.sinovoip.com.cn/ecp_view.asp?id=586>)
+	  (<https://tibbo.com/store/plus1.html>)
+
+if ARCH_SUNPLUS
+
+config SOC_SP7021
+	bool "Sunplus SP7021 SoC support"
+	default ARCH_SUNPLUS
+	select HAVE_ARM_ARCH_TIMER
+	select ARM_GIC
+	select ARM_PSCI
+	select PINCTRL
+	select PINCTRL_SPPCTL
+	select SERIAL_SUNPLUS if TTY
+	select SERIAL_SUNPLUS_CONSOLE if TTY
+	help
+	  Support for Sunplus SP7021 SoC. It is based on ARM 4-core
+	  Cortex-A7 with various peripherals (e.g.: I2C, SPI, SDIO,
+	  Ethernet, etc.), FPGA interface,  chip-to-chip bus.
+	  It is designed for industrial control.
+
+endif
+
+config ARCH_UNIPHIER
+	bool "Socionext UniPhier SoCs"
+	depends on ARCH_MULTI_V7
+	select ARCH_HAS_RESET_CONTROLLER
+	select ARM_AMBA
+	select ARM_GLOBAL_TIMER
+	select ARM_GIC
+	select HAVE_ARM_SCU
+	select HAVE_ARM_TWD if SMP
+	select PINCTRL
+	select RESET_CONTROLLER
+	help
+	  Support for UniPhier SoC family developed by Socionext Inc.
+	  (formerly, System LSI Business Division of Panasonic Corporation)
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index a2391b8de5a5..b7de4b6b284c 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -22,6 +22,9 @@ GZFLAGS		:=-9
 # Never generate .eh_frame
 KBUILD_CFLAGS	+= $(call cc-option,-fno-dwarf2-cfi-asm)
 
+# Disable FDPIC ABI
+KBUILD_CFLAGS	+= $(call cc-option,-mno-fdpic)
+
 # This should work on most of the modern platforms
 KBUILD_DEFCONFIG := multi_v7_defconfig
 
@@ -57,47 +60,54 @@ endif
 KBUILD_CFLAGS	+= $(call cc-option,-fno-ipa-sra)
 
 # This selects which instruction set is used.
+arch-$(CONFIG_CPU_32v7M)	:=-march=armv7-m
+arch-$(CONFIG_CPU_32v7)		:=-march=armv7-a
+arch-$(CONFIG_CPU_32v6)		:=-march=armv6
+# Only override the compiler option if ARMv6. The ARMv6K extensions are
+# always available in ARMv7
+ifeq ($(CONFIG_CPU_32v6),y)
+arch-$(CONFIG_CPU_32v6K)	:=-march=armv6k
+endif
+arch-$(CONFIG_CPU_32v5)		:=-march=armv5te
+arch-$(CONFIG_CPU_32v4T)	:=-march=armv4t
+arch-$(CONFIG_CPU_32v4)		:=-march=armv4
+arch-$(CONFIG_CPU_32v3)		:=-march=armv3m
+
 # Note that GCC does not numerically define an architecture version
 # macro, but instead defines a whole series of macros which makes
 # testing for a specific architecture or later rather impossible.
-arch-$(CONFIG_CPU_32v7M)	=-D__LINUX_ARM_ARCH__=7 -march=armv7-m
-arch-$(CONFIG_CPU_32v7)		=-D__LINUX_ARM_ARCH__=7 -march=armv7-a
-arch-$(CONFIG_CPU_32v6)		=-D__LINUX_ARM_ARCH__=6 -march=armv6
+cpp-$(CONFIG_CPU_32v7M)		:=-D__LINUX_ARM_ARCH__=7
+cpp-$(CONFIG_CPU_32v7)		:=-D__LINUX_ARM_ARCH__=7
+cpp-$(CONFIG_CPU_32v6)		:=-D__LINUX_ARM_ARCH__=6
 # Only override the compiler option if ARMv6. The ARMv6K extensions are
 # always available in ARMv7
 ifeq ($(CONFIG_CPU_32v6),y)
-arch-$(CONFIG_CPU_32v6K)	=-D__LINUX_ARM_ARCH__=6 -march=armv6k
+cpp-$(CONFIG_CPU_32v6K)		:=-D__LINUX_ARM_ARCH__=6
 endif
-arch-$(CONFIG_CPU_32v5)		=-D__LINUX_ARM_ARCH__=5 -march=armv5te
-arch-$(CONFIG_CPU_32v4T)	=-D__LINUX_ARM_ARCH__=4 -march=armv4t
-arch-$(CONFIG_CPU_32v4)		=-D__LINUX_ARM_ARCH__=4 -march=armv4
-arch-$(CONFIG_CPU_32v3)		=-D__LINUX_ARM_ARCH__=3 -march=armv3m
-
-# Evaluate arch cc-option calls now
-arch-y := $(arch-y)
+cpp-$(CONFIG_CPU_32v5)		:=-D__LINUX_ARM_ARCH__=5
+cpp-$(CONFIG_CPU_32v4T)		:=-D__LINUX_ARM_ARCH__=4
+cpp-$(CONFIG_CPU_32v4)		:=-D__LINUX_ARM_ARCH__=4
+cpp-$(CONFIG_CPU_32v3)		:=-D__LINUX_ARM_ARCH__=3
 
 # This selects how we optimise for the processor.
-tune-$(CONFIG_CPU_ARM7TDMI)	=-mtune=arm7tdmi
-tune-$(CONFIG_CPU_ARM720T)	=-mtune=arm7tdmi
-tune-$(CONFIG_CPU_ARM740T)	=-mtune=arm7tdmi
-tune-$(CONFIG_CPU_ARM9TDMI)	=-mtune=arm9tdmi
-tune-$(CONFIG_CPU_ARM940T)	=-mtune=arm9tdmi
-tune-$(CONFIG_CPU_ARM946E)	=-mtune=arm9e
-tune-$(CONFIG_CPU_ARM920T)	=-mtune=arm9tdmi
-tune-$(CONFIG_CPU_ARM922T)	=-mtune=arm9tdmi
-tune-$(CONFIG_CPU_ARM925T)	=-mtune=arm9tdmi
-tune-$(CONFIG_CPU_ARM926T)	=-mtune=arm9tdmi
-tune-$(CONFIG_CPU_FA526)	=-mtune=arm9tdmi
-tune-$(CONFIG_CPU_SA110)	=-mtune=strongarm110
-tune-$(CONFIG_CPU_SA1100)	=-mtune=strongarm1100
-tune-$(CONFIG_CPU_XSCALE)	=-mtune=xscale
-tune-$(CONFIG_CPU_XSC3)		=-mtune=xscale
-tune-$(CONFIG_CPU_FEROCEON)	=-mtune=xscale
-tune-$(CONFIG_CPU_V6)		=-mtune=arm1136j-s
-tune-$(CONFIG_CPU_V6K)		=-mtune=arm1136j-s
-
-# Evaluate tune cc-option calls now
-tune-y := $(tune-y)
+tune-$(CONFIG_CPU_ARM7TDMI)	:=-mtune=arm7tdmi
+tune-$(CONFIG_CPU_ARM720T)	:=-mtune=arm7tdmi
+tune-$(CONFIG_CPU_ARM740T)	:=-mtune=arm7tdmi
+tune-$(CONFIG_CPU_ARM9TDMI)	:=-mtune=arm9tdmi
+tune-$(CONFIG_CPU_ARM940T)	:=-mtune=arm9tdmi
+tune-$(CONFIG_CPU_ARM946E)	:=-mtune=arm9e
+tune-$(CONFIG_CPU_ARM920T)	:=-mtune=arm9tdmi
+tune-$(CONFIG_CPU_ARM922T)	:=-mtune=arm9tdmi
+tune-$(CONFIG_CPU_ARM925T)	:=-mtune=arm9tdmi
+tune-$(CONFIG_CPU_ARM926T)	:=-mtune=arm9tdmi
+tune-$(CONFIG_CPU_FA526)	:=-mtune=arm9tdmi
+tune-$(CONFIG_CPU_SA110)	:=-mtune=strongarm110
+tune-$(CONFIG_CPU_SA1100)	:=-mtune=strongarm1100
+tune-$(CONFIG_CPU_XSCALE)	:=-mtune=xscale
+tune-$(CONFIG_CPU_XSC3)		:=-mtune=xscale
+tune-$(CONFIG_CPU_FEROCEON)	:=-mtune=xscale
+tune-$(CONFIG_CPU_V6)		:=-mtune=arm1136j-s
+tune-$(CONFIG_CPU_V6K)		:=-mtune=arm1136j-s
 
 ifeq ($(CONFIG_AEABI),y)
 CFLAGS_ABI	:=-mabi=aapcs-linux -mfpu=vfp
@@ -114,53 +124,55 @@ CFLAGS_ABI	+= -meabi gnu
 endif
 
 ifeq ($(CONFIG_CURRENT_POINTER_IN_TPIDRURO),y)
-CFLAGS_ABI	+= -mtp=cp15
+KBUILD_CFLAGS	+= -mtp=cp15
 endif
 
 # Accept old syntax despite ".syntax unified"
 AFLAGS_NOWARN	:=$(call as-option,-Wa$(comma)-mno-warn-deprecated,-Wa$(comma)-W)
 
+# The GCC option -ffreestanding is required in order to compile code containing
+# ARM/NEON intrinsics in a non C99-compliant environment (such as the kernel)
+CC_FLAGS_FPU	:= -ffreestanding
+# Enable <arm_neon.h>
+CC_FLAGS_FPU	+= -isystem $(shell $(CC) -print-file-name=include)
+CC_FLAGS_FPU	+= -march=armv7-a -mfloat-abi=softfp -mfpu=neon
+
 ifeq ($(CONFIG_THUMB2_KERNEL),y)
-CFLAGS_ISA	:=-mthumb -Wa,-mimplicit-it=always $(AFLAGS_NOWARN)
+CFLAGS_ISA	:=-Wa,-mimplicit-it=always $(AFLAGS_NOWARN)
 AFLAGS_ISA	:=$(CFLAGS_ISA) -Wa$(comma)-mthumb
+CFLAGS_ISA	+=-mthumb
 else
 CFLAGS_ISA	:=$(call cc-option,-marm,) $(AFLAGS_NOWARN)
 AFLAGS_ISA	:=$(CFLAGS_ISA)
 endif
 
 # Need -Uarm for gcc < 3.x
+KBUILD_CPPFLAGS	+=$(cpp-y)
 KBUILD_CFLAGS	+=$(CFLAGS_ABI) $(CFLAGS_ISA) $(arch-y) $(tune-y) $(call cc-option,-mshort-load-bytes,$(call cc-option,-malignment-traps,)) -msoft-float -Uarm
-KBUILD_AFLAGS	+=$(CFLAGS_ABI) $(AFLAGS_ISA) $(arch-y) $(tune-y) -include asm/unified.h -msoft-float
+KBUILD_AFLAGS	+=$(CFLAGS_ABI) $(AFLAGS_ISA) -Wa,$(arch-y) $(tune-y) -include $(srctree)/arch/arm/include/asm/unified.h -msoft-float
+KBUILD_RUSTFLAGS += --target=arm-unknown-linux-gnueabi
 
 CHECKFLAGS	+= -D__arm__
 
-#Default value
-head-y		:= arch/arm/kernel/head$(MMUEXT).o
-
 # Text offset. This list is sorted numerically by address in order to
 # provide a means to avoid/resolve conflicts in multi-arch kernels.
 # Note: the 32kB below this value is reserved for use by the kernel
 # during boot, and this offset is critical to the functioning of
 # kexec-tools.
 textofs-y	:= 0x00008000
-# We don't want the htc bootloader to corrupt kernel during resume
-textofs-$(CONFIG_PM_H1940)      := 0x00108000
 # RTD1195 has Boot ROM at start of address space
 textofs-$(CONFIG_ARCH_REALTEK)  := 0x00108000
 # SA1111 DMA bug: we don't want the kernel to live in precious DMA-able memory
 ifeq ($(CONFIG_ARCH_SA1100),y)
 textofs-$(CONFIG_SA1111) := 0x00208000
 endif
-textofs-$(CONFIG_ARCH_IPQ40XX) := 0x00208000
-textofs-$(CONFIG_ARCH_MSM8X60) := 0x00208000
-textofs-$(CONFIG_ARCH_MSM8960) := 0x00208000
+textofs-$(CONFIG_ARCH_QCOM_RESERVE_SMEM) := 0x00208000
 textofs-$(CONFIG_ARCH_MESON) := 0x00208000
 textofs-$(CONFIG_ARCH_AXXIA) := 0x00308000
 
 # Machine directory name.  This list is sorted alphanumerically
 # by CONFIG_* macro name.
 machine-$(CONFIG_ARCH_ACTIONS)		+= actions
-machine-$(CONFIG_ARCH_AIROHA)		+= airoha
 machine-$(CONFIG_ARCH_ALPINE)		+= alpine
 machine-$(CONFIG_ARCH_ARTPEC)		+= artpec
 machine-$(CONFIG_ARCH_ASPEED)           += aspeed
@@ -169,26 +181,20 @@ machine-$(CONFIG_ARCH_AXXIA)		+= axxia
 machine-$(CONFIG_ARCH_BCM)		+= bcm
 machine-$(CONFIG_ARCH_BERLIN)		+= berlin
 machine-$(CONFIG_ARCH_CLPS711X)		+= clps711x
-machine-$(CONFIG_ARCH_CNS3XXX)		+= cns3xxx
 machine-$(CONFIG_ARCH_DAVINCI)		+= davinci
 machine-$(CONFIG_ARCH_DIGICOLOR)	+= digicolor
 machine-$(CONFIG_ARCH_DOVE)		+= dove
-machine-$(CONFIG_ARCH_EP93XX)		+= ep93xx
 machine-$(CONFIG_ARCH_EXYNOS)		+= exynos
 machine-$(CONFIG_ARCH_FOOTBRIDGE)	+= footbridge
 machine-$(CONFIG_ARCH_GEMINI)		+= gemini
 machine-$(CONFIG_ARCH_HIGHBANK)		+= highbank
 machine-$(CONFIG_ARCH_HISI)		+= hisi
-machine-$(CONFIG_ARCH_INTEGRATOR)	+= integrator
-machine-$(CONFIG_ARCH_IOP32X)		+= iop32x
 machine-$(CONFIG_ARCH_IXP4XX)		+= ixp4xx
 machine-$(CONFIG_ARCH_KEYSTONE)		+= keystone
 machine-$(CONFIG_ARCH_LPC18XX)		+= lpc18xx
 machine-$(CONFIG_ARCH_LPC32XX)		+= lpc32xx
 machine-$(CONFIG_ARCH_MESON)		+= meson
 machine-$(CONFIG_ARCH_MMP)		+= mmp
-machine-$(CONFIG_ARCH_MPS2)		+= vexpress
-machine-$(CONFIG_ARCH_MOXART)		+= moxart
 machine-$(CONFIG_ARCH_MV78XX0)		+= mv78xx0
 machine-$(CONFIG_ARCH_MVEBU)		+= mvebu
 machine-$(CONFIG_ARCH_MXC)		+= imx
@@ -198,16 +204,12 @@ machine-$(CONFIG_ARCH_MXS)		+= mxs
 machine-$(CONFIG_ARCH_MSTARV7)		+= mstar
 machine-$(CONFIG_ARCH_NOMADIK)		+= nomadik
 machine-$(CONFIG_ARCH_NPCM)		+= npcm
-machine-$(CONFIG_ARCH_NSPIRE)		+= nspire
-machine-$(CONFIG_ARCH_OXNAS)		+= oxnas
 machine-$(CONFIG_ARCH_OMAP1)		+= omap1
 machine-$(CONFIG_ARCH_OMAP2PLUS)	+= omap2
 machine-$(CONFIG_ARCH_ORION5X)		+= orion5x
 machine-$(CONFIG_ARCH_PXA)		+= pxa
 machine-$(CONFIG_ARCH_QCOM)		+= qcom
-machine-$(CONFIG_ARCH_RDA)		+= rda
 machine-$(CONFIG_ARCH_REALTEK)		+= realtek
-machine-$(CONFIG_ARCH_REALVIEW)		+= realview
 machine-$(CONFIG_ARCH_ROCKCHIP)		+= rockchip
 machine-$(CONFIG_ARCH_RPC)		+= rpc
 machine-$(CONFIG_PLAT_SAMSUNG)		+= s3c
@@ -220,49 +222,29 @@ machine-$(CONFIG_ARCH_STM32)		+= stm32
 machine-$(CONFIG_ARCH_SUNXI)		+= sunxi
 machine-$(CONFIG_ARCH_TEGRA)		+= tegra
 machine-$(CONFIG_ARCH_U8500)		+= ux500
-machine-$(CONFIG_ARCH_VERSATILE)	+= versatile
-machine-$(CONFIG_ARCH_VEXPRESS)		+= vexpress
 machine-$(CONFIG_ARCH_VT8500)		+= vt8500
 machine-$(CONFIG_ARCH_ZYNQ)		+= zynq
+machine-$(CONFIG_PLAT_VERSATILE)	+= versatile
 machine-$(CONFIG_PLAT_SPEAR)		+= spear
 
-# Platform directory name.  This list is sorted alphanumerically
-# by CONFIG_* macro name.
-plat-$(CONFIG_ARCH_OMAP)	+= omap
-plat-$(CONFIG_PLAT_ORION)	+= orion
-plat-$(CONFIG_PLAT_PXA)		+= pxa
-plat-$(CONFIG_PLAT_VERSATILE)	+= versatile
+# legacy platforms provide their own mach/*.h headers globally,
+# these three are mutually exclusive
+machdirs-$(CONFIG_ARCH_FOOTBRIDGE)	+= arch/arm/mach-footbridge
+machdirs-$(CONFIG_ARCH_RPC)		+= arch/arm/mach-rpc
+machdirs-$(CONFIG_ARCH_SA1100)		+= arch/arm/mach-sa1100
+KBUILD_CPPFLAGS += $(patsubst %,-I$(srctree)/%/include,$(machdirs-y))
 
 # The byte offset of the kernel image in RAM from the start of RAM.
 TEXT_OFFSET := $(textofs-y)
 
-# The first directory contains additional information for the boot setup code
-ifneq ($(machine-y),)
-MACHINE  := arch/arm/mach-$(word 1,$(machine-y))/
-else
-MACHINE  :=
-endif
-ifeq ($(CONFIG_ARCH_MULTIPLATFORM),y)
-MACHINE  :=
-endif
-
-machdirs := $(patsubst %,arch/arm/mach-%/,$(machine-y))
-platdirs := $(patsubst %,arch/arm/plat-%/,$(sort $(plat-y)))
-
-ifneq ($(CONFIG_ARCH_MULTIPLATFORM),y)
-ifneq ($(CONFIG_ARM_SINGLE_ARMV7M),y)
-KBUILD_CPPFLAGS += $(patsubst %,-I$(srctree)/%include,$(machdirs) $(platdirs))
-endif
-endif
-
 export	TEXT_OFFSET GZFLAGS MMUEXT
 
 # If we have a machine-specific directory, then include it in the build.
-core-y				+= $(machdirs) $(platdirs)
-
+core-y				+= $(patsubst %,arch/arm/mach-%/,$(machine-y))
 # For cleaning
-core-				+= $(patsubst %,arch/arm/mach-%/, $(machine-))
-core-				+= $(patsubst %,arch/arm/plat-%/, $(plat-))
+core-				+= $(patsubst %,arch/arm/mach-%/,$(machine-))
+
+core-$(CONFIG_PLAT_ORION)	+= arch/arm/plat-orion/
 
 libs-y				:= arch/arm/lib/ $(libs-y)
 
@@ -282,13 +264,13 @@ stack_protector_prepare: prepare0
 		-mstack-protector-guard=tls \
 		-mstack-protector-guard-offset=$(shell	\
 			awk '{if ($$2 == "TSK_STACK_CANARY") print $$3;}'\
-				include/generated/asm-offsets.h))
+				$(objtree)/include/generated/asm-offsets.h))
 else
 stack_protector_prepare: prepare0
 	$(eval SSP_PLUGIN_CFLAGS := \
 		-fplugin-arg-arm_ssp_per_task_plugin-offset=$(shell	\
 			awk '{if ($$2 == "TSK_STACK_CANARY") print $$3;}'\
-				include/generated/asm-offsets.h))
+				$(objtree)/include/generated/asm-offsets.h))
 	$(eval KBUILD_CFLAGS += $(SSP_PLUGIN_CFLAGS))
 	$(eval GCC_PLUGINS_CFLAGS += $(SSP_PLUGIN_CFLAGS))
 endif
@@ -315,22 +297,22 @@ bootpImage uImage: zImage
 zImage: Image
 
 $(BOOT_TARGETS): vmlinux
-	$(Q)$(MAKE) $(build)=$(boot) MACHINE=$(MACHINE) $(boot)/$@
+	$(Q)$(MAKE) $(build)=$(boot) $(boot)/$@
 	@$(kecho) '  Kernel: $(boot)/$@ is ready'
 
+$(INSTALL_TARGETS): KBUILD_IMAGE = $(boot)/$(patsubst %install,%Image,$@)
 $(INSTALL_TARGETS):
-	$(CONFIG_SHELL) $(srctree)/$(boot)/install.sh "$(KERNELRELEASE)" \
-	$(boot)/$(patsubst %install,%Image,$@) System.map "$(INSTALL_PATH)"
+	$(call cmd,install)
 
-PHONY += vdso_install
-vdso_install:
-ifeq ($(CONFIG_VDSO),y)
-	$(Q)$(MAKE) $(build)=arch/arm/vdso $@
-endif
+vdso-install-$(CONFIG_VDSO) += arch/arm/vdso/vdso.so.dbg
 
 # My testing targets (bypasses dependencies)
-bp:;	$(Q)$(MAKE) $(build)=$(boot) MACHINE=$(MACHINE) $(boot)/bootpImage
+bp:;	$(Q)$(MAKE) $(build)=$(boot) $(boot)/bootpImage
 
+include $(srctree)/scripts/Makefile.defconf
+PHONY += multi_v7_lpae_defconfig
+multi_v7_lpae_defconfig:
+	$(call merge_into_defconfig,multi_v7_defconfig,lpae)
 
 define archhelp
   echo  '* zImage        - Compressed kernel image (arch/$(ARCH)/boot/zImage)'
@@ -345,5 +327,6 @@ define archhelp
   echo  '                  Install using (your) ~/bin/$(INSTALLKERNEL) or'
   echo  '                  (distribution) /sbin/$(INSTALLKERNEL) or'
   echo  '                  install to $$(INSTALL_PATH) and run lilo'
-  echo  '  vdso_install  - Install unstripped vdso.so to $$(INSTALL_MOD_PATH)/vdso'
+  echo
+  echo  '  multi_v7_lpae_defconfig     - multi_v7_defconfig with CONFIG_ARM_LPAE enabled'
 endef
diff --git a/arch/arm/boot/Makefile b/arch/arm/boot/Makefile
index 54a09f9464fb..ba9b9a802469 100644
--- a/arch/arm/boot/Makefile
+++ b/arch/arm/boot/Makefile
@@ -10,29 +10,22 @@
 #
 # Copyright (C) 1995-2002 Russell King
 #
-
 OBJCOPYFLAGS	:=-O binary -R .comment -S
 
-ifneq ($(MACHINE),)
-include $(MACHINE)/Makefile.boot
-endif
-
-# Note: the following conditions must always be true:
 #   ZRELADDR == virt_to_phys(PAGE_OFFSET + TEXT_OFFSET)
-#   PARAMS_PHYS must be within 4MB of ZRELADDR
-#   INITRD_PHYS must be in RAM
-ZRELADDR    := $(zreladdr-y)
-PARAMS_PHYS := $(params_phys-y)
-INITRD_PHYS := $(initrd_phys-y)
+ifdef CONFIG_PHYS_OFFSET
+add_hex = $(shell printf 0x%x $$(( $(1) + $(2) )) )
+ZRELADDR    := $(call add_hex, $(CONFIG_PHYS_OFFSET), $(TEXT_OFFSET))
+endif
 
-export ZRELADDR INITRD_PHYS PARAMS_PHYS
+PHYS_OFFSET := $(CONFIG_PHYS_OFFSET)
+export ZRELADDR PARAMS_PHYS PHYS_OFFSET
 
 targets := Image zImage xipImage bootpImage uImage
 
 ifeq ($(CONFIG_XIP_KERNEL),y)
 
-cmd_deflate_xip_data = $(CONFIG_SHELL) -c \
-	'$(srctree)/$(src)/deflate_xip_data.sh $< $@'
+cmd_deflate_xip_data = $(CONFIG_SHELL) -c '$(src)/deflate_xip_data.sh $< $@'
 
 ifeq ($(CONFIG_XIP_DEFLATED_DATA),y)
 quiet_cmd_mkxip = XIPZ    $@
@@ -90,17 +83,10 @@ $(obj)/uImage:	$(obj)/zImage FORCE
 	@$(check_for_multiple_loadaddr)
 	$(call if_changed,uimage)
 
-$(obj)/bootp/bootp: $(obj)/zImage initrd FORCE
+$(obj)/bootp/bootp: $(obj)/zImage FORCE
 	$(Q)$(MAKE) $(build)=$(obj)/bootp $@
 
 $(obj)/bootpImage: $(obj)/bootp/bootp FORCE
 	$(call if_changed,objcopy)
 
-PHONY += initrd
-initrd:
-	@test "$(INITRD_PHYS)" != "" || \
-	(echo This machine does not support INITRD; exit -1)
-	@test "$(INITRD)" != "" || \
-	(echo You must specify INITRD; exit -1)
-
 subdir-	    := bootp compressed dts
diff --git a/arch/arm/boot/bootp/Makefile b/arch/arm/boot/bootp/Makefile
index 981a8d03f064..f3443f7d7b02 100644
--- a/arch/arm/boot/bootp/Makefile
+++ b/arch/arm/boot/bootp/Makefile
@@ -6,7 +6,37 @@
 # architecture-specific flags and dependencies.
 #
 
-GCOV_PROFILE	:= n
+ifdef PHYS_OFFSET
+add_hex = $(shell printf 0x%x $$(( $(1) + $(2) )) )
+
+# If PHYS_OFFSET is set, INITRD_PHYS and PARAMS_PHYS can be derived,
+# otherwise they must be passed on the command line.
+#
+# Note: the following conditions must always be true:
+#   PARAMS_PHYS must be within 4MB of ZRELADDR
+#   INITRD_PHYS must be in RAM
+
+PARAMS_PHYS := $(call add_hex, $(PHYS_OFFSET), 0x100)
+
+# guess an initrd location if possible
+initrd_offset-$(CONFIG_ARCH_FOOTBRIDGE)	+= 0x00800000
+initrd_offset-$(CONFIG_ARCH_SA1100)	+= 0x00800000
+initrd_offset-$(CONFIG_ARCH_RPC)	+= 0x08000000
+INITRD_OFFSET := $(initrd_offset-y)
+ifdef INITRD_OFFSET
+INITRD_PHYS := $(call add_hex, $(PHYS_OFFSET), $(INITRD_OFFSET))
+endif
+
+endif
+
+PHONY += initrd
+initrd:
+	@test "$(PARAMS_PHYS)" != "" || \
+	(echo bootpImage: You must specify PHYS_OFFSET of PARAMS_PHYS ; exit -1)
+	@test "$(INITRD_PHYS)" != "" || \
+	(echo bootpImage: You must specify INITRD_OFFSET or INITRD_PHYS ; exit -1)
+	@test "$(INITRD)" != "" || \
+	(echo bootpImage: You must specify INITRD; exit -1)
 
 LDFLAGS_bootp	:= --no-undefined -X \
 		 --defsym initrd_phys=$(INITRD_PHYS) \
@@ -24,6 +54,6 @@ $(obj)/bootp:	$(src)/bootp.lds $(addprefix $(obj)/,init.o kernel.o initrd.o) FOR
 
 $(obj)/kernel.o: arch/arm/boot/zImage FORCE
 
-$(obj)/initrd.o: $(INITRD) FORCE
+$(obj)/initrd.o: initrd $(INITRD) FORCE
 
 PHONY += $(INITRD)
diff --git a/arch/arm/boot/bootp/bootp.lds b/arch/arm/boot/bootp/bootp.lds
index fc54394f4340..160128186bf8 100644
--- a/arch/arm/boot/bootp/bootp.lds
+++ b/arch/arm/boot/bootp/bootp.lds
@@ -1,11 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  *  linux/arch/arm/boot/bootp/bootp.lds
  *
  *  Copyright (C) 2000-2002 Russell King
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
  */
 OUTPUT_ARCH(arm)
 ENTRY(_start)
diff --git a/arch/arm/boot/compressed/Makefile b/arch/arm/boot/compressed/Makefile
index 41bcbb460fac..a159120d1e42 100644
--- a/arch/arm/boot/compressed/Makefile
+++ b/arch/arm/boot/compressed/Makefile
@@ -22,12 +22,6 @@ ifeq ($(CONFIG_ARM_VIRT_EXT),y)
 OBJS		+= hyp-stub.o
 endif
 
-GCOV_PROFILE		:= n
-KASAN_SANITIZE		:= n
-
-# Prevents link failures: __sanitizer_cov_trace_pc() is not linked in.
-KCOV_INSTRUMENT		:= n
-
 #
 # Architecture dependencies
 #
@@ -101,12 +95,13 @@ KBUILD_CFLAGS += -DDISABLE_BRANCH_PROFILING
 
 ccflags-y := -fpic $(call cc-option,-mno-single-pic-base,) -fno-builtin \
 	     -I$(srctree)/scripts/dtc/libfdt -fno-stack-protector \
-	     -I$(obj) $(DISABLE_ARM_SSP_PER_TASK_PLUGIN)
+	     $(DISABLE_KSTACK_ERASE) \
+	     -I$(obj)
 ccflags-remove-$(CONFIG_FUNCTION_TRACER) += -pg
 asflags-y := -DZIMAGE
 
 # Supply kernel BSS size to the decompressor via a linker symbol.
-KBSS_SZ = $(shell echo $$(($$($(NM) $(obj)/../../../../vmlinux | \
+KBSS_SZ = $(shell echo $$(($$($(NM) vmlinux | \
 		sed -n -e 's/^\([^ ]*\) [ABD] __bss_start$$/-0x\1/p' \
 		       -e 's/^\([^ ]*\) [ABD] __bss_stop$$/+0x\1/p') )) )
 LDFLAGS_vmlinux = --defsym _kernel_bss_size=$(KBSS_SZ)
@@ -123,7 +118,7 @@ LDFLAGS_vmlinux += --no-undefined
 LDFLAGS_vmlinux += -X
 # Report orphan sections
 ifdef CONFIG_LD_ORPHAN_WARN
-LDFLAGS_vmlinux += --orphan-handling=warn
+LDFLAGS_vmlinux += --orphan-handling=$(CONFIG_LD_ORPHAN_WARN_LEVEL)
 endif
 # Next argument is a linker script
 LDFLAGS_vmlinux += -T
@@ -163,4 +158,3 @@ $(obj)/piggy_data: $(obj)/../Image FORCE
 $(obj)/piggy.o: $(obj)/piggy_data
 
 CFLAGS_font.o := -Dstatic=
-AFLAGS_hyp-stub.o := -Wa,-march=armv7-a
diff --git a/arch/arm/boot/compressed/atags_to_fdt.c b/arch/arm/boot/compressed/atags_to_fdt.c
index 1feb6b0f7a1f..627752f18661 100644
--- a/arch/arm/boot/compressed/atags_to_fdt.c
+++ b/arch/arm/boot/compressed/atags_to_fdt.c
@@ -2,6 +2,7 @@
 #include <linux/libfdt_env.h>
 #include <asm/setup.h>
 #include <libfdt.h>
+#include "misc.h"
 
 #if defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND)
 #define do_extend_cmdline 1
diff --git a/arch/arm/boot/compressed/decompress.c b/arch/arm/boot/compressed/decompress.c
index 74255e819831..0669851394f0 100644
--- a/arch/arm/boot/compressed/decompress.c
+++ b/arch/arm/boot/compressed/decompress.c
@@ -31,6 +31,7 @@
 /* Not needed, but used in some headers pulled in by decompressors */
 extern char * strstr(const char * s1, const char *s2);
 extern size_t strlen(const char *s);
+extern int strcmp(const char *cs, const char *ct);
 extern int memcmp(const void *cs, const void *ct, size_t count);
 extern char * strchrnul(const char *, int);
 
diff --git a/arch/arm/boot/compressed/efi-header.S b/arch/arm/boot/compressed/efi-header.S
index 230030c13085..65a3025c0e13 100644
--- a/arch/arm/boot/compressed/efi-header.S
+++ b/arch/arm/boot/compressed/efi-header.S
@@ -20,7 +20,7 @@
 		@ is accepted as an EFI binary. Booting via the UEFI stub
 		@ will not execute those instructions, but the ARM/Linux
 		@ boot protocol does, so we need some NOPs here.
-		.inst	MZ_MAGIC | (0xe225 << 16)	@ eor r5, r5, 0x4d000
+		.inst	IMAGE_DOS_SIGNATURE | (0xe225 << 16) @ eor r5, r5, 0x4d000
 		eor	r5, r5, 0x4d000			@ undo previous insn
 #else
 		__nop
@@ -43,7 +43,7 @@
 		.long	pe_header - start		@ Offset to the PE header.
 
 pe_header:
-		.long	PE_MAGIC
+		.long	IMAGE_NT_SIGNATURE
 
 coff_header:
 		.short	IMAGE_FILE_MACHINE_THUMB	@ Machine
@@ -60,7 +60,7 @@ coff_header:
 #define __pecoff_code_size (__pecoff_data_start - __efi_start)
 
 optional_header:
-		.short	PE_OPT_MAGIC_PE32		@ PE32 format
+		.short	IMAGE_NT_OPTIONAL_HDR32_MAGIC	@ PE32 format
 		.byte	0x02				@ MajorLinkerVersion
 		.byte	0x14				@ MinorLinkerVersion
 		.long	__pecoff_code_size		@ SizeOfCode
diff --git a/arch/arm/boot/compressed/fdt_check_mem_start.c b/arch/arm/boot/compressed/fdt_check_mem_start.c
index 9291a2661bdf..aa856567fd33 100644
--- a/arch/arm/boot/compressed/fdt_check_mem_start.c
+++ b/arch/arm/boot/compressed/fdt_check_mem_start.c
@@ -3,6 +3,7 @@
 #include <linux/kernel.h>
 #include <linux/libfdt.h>
 #include <linux/sizes.h>
+#include "misc.h"
 
 static const void *get_prop(const void *fdt, const char *node_path,
 			    const char *property, int minlen)
diff --git a/arch/arm/boot/compressed/head-sa1100.S b/arch/arm/boot/compressed/head-sa1100.S
index 95abdd850fe3..23eae1a65064 100644
--- a/arch/arm/boot/compressed/head-sa1100.S
+++ b/arch/arm/boot/compressed/head-sa1100.S
@@ -20,10 +20,6 @@ __SA1100_start:
 #ifdef CONFIG_SA1100_COLLIE
 		mov	r7, #MACH_TYPE_COLLIE
 #endif
-#ifdef CONFIG_SA1100_SIMPAD
-		@ UNTIL we've something like an open bootldr
-		mov	r7, #MACH_TYPE_SIMPAD	@should be 87
-#endif
 		mrc	p15, 0, r0, c1, c0, 0	@ read control reg
 		ands	r0, r0, #0x0d
 		beq	99f
diff --git a/arch/arm/boot/compressed/head.S b/arch/arm/boot/compressed/head.S
index bf79f2f78d23..9f406e9c0ea6 100644
--- a/arch/arm/boot/compressed/head.S
+++ b/arch/arm/boot/compressed/head.S
@@ -67,11 +67,7 @@
 #if defined(CONFIG_ARCH_SA1100)
 		.macro	loadsp, rb, tmp1, tmp2
 		mov	\rb, #0x80000000	@ physical base address
-#ifdef CONFIG_DEBUG_LL_SER3
-		add	\rb, \rb, #0x00050000	@ Ser3
-#else
 		add	\rb, \rb, #0x00010000	@ Ser1
-#endif
 		.endm
 #else
 		.macro	loadsp,	rb, tmp1, tmp2
diff --git a/arch/arm/mach-ep93xx/include/mach/uncompress.h b/arch/arm/boot/compressed/misc-ep93xx.h
index b3ec1db988db..65b4121d1490 100644
--- a/arch/arm/mach-ep93xx/include/mach/uncompress.h
+++ b/arch/arm/boot/compressed/misc-ep93xx.h
@@ -1,55 +1,25 @@
 /* SPDX-License-Identifier: GPL-2.0-or-later */
 /*
- * arch/arm/mach-ep93xx/include/mach/uncompress.h
- *
  * Copyright (C) 2006 Lennert Buytenhek <buytenh@wantstofly.org>
  */
 
-#include <mach/ep93xx-regs.h>
 #include <asm/mach-types.h>
 
-static unsigned char __raw_readb(unsigned int ptr)
-{
-	return *((volatile unsigned char *)ptr);
-}
-
-static unsigned int __raw_readl(unsigned int ptr)
+static inline unsigned int __raw_readl(unsigned int ptr)
 {
 	return *((volatile unsigned int *)ptr);
 }
 
-static void __raw_writeb(unsigned char value, unsigned int ptr)
+static inline void __raw_writeb(unsigned char value, unsigned int ptr)
 {
 	*((volatile unsigned char *)ptr) = value;
 }
 
-static void __raw_writel(unsigned int value, unsigned int ptr)
+static inline void __raw_writel(unsigned int value, unsigned int ptr)
 {
 	*((volatile unsigned int *)ptr) = value;
 }
 
-#define PHYS_UART_DATA		(CONFIG_DEBUG_UART_PHYS + 0x00)
-#define PHYS_UART_FLAG		(CONFIG_DEBUG_UART_PHYS + 0x18)
-#define UART_FLAG_TXFF		0x20
-
-static inline void putc(int c)
-{
-	int i;
-
-	for (i = 0; i < 10000; i++) {
-		/* Transmit fifo not full? */
-		if (!(__raw_readb(PHYS_UART_FLAG) & UART_FLAG_TXFF))
-			break;
-	}
-
-	__raw_writeb(c, PHYS_UART_DATA);
-}
-
-static inline void flush(void)
-{
-}
-
-
 /*
  * Some bootloaders don't turn off DMA from the ethernet MAC before
  * jumping to linux, which means that we might end up with bits of RX
@@ -59,7 +29,7 @@ static inline void flush(void)
 #define PHYS_ETH_SELF_CTL		0x80010020
 #define ETH_SELF_CTL_RESET		0x00000001
 
-static void ethernet_reset(void)
+static inline void ep93xx_ethernet_reset(void)
 {
 	unsigned int v;
 
@@ -76,15 +46,30 @@ static void ethernet_reset(void)
 #define TS72XX_WDT_FEED_PHYS_BASE	0x23c00000
 #define TS72XX_WDT_FEED_VAL		0x05
 
-static void __maybe_unused ts72xx_watchdog_disable(void)
+static inline void __maybe_unused ts72xx_watchdog_disable(void)
 {
 	__raw_writeb(TS72XX_WDT_FEED_VAL, TS72XX_WDT_FEED_PHYS_BASE);
 	__raw_writeb(0, TS72XX_WDT_CONTROL_PHYS_BASE);
 }
 
-static void arch_decomp_setup(void)
+static inline void ep93xx_decomp_setup(void)
 {
 	if (machine_is_ts72xx())
 		ts72xx_watchdog_disable();
-	ethernet_reset();
+
+	if (machine_is_edb9301() ||
+	    machine_is_edb9302() ||
+	    machine_is_edb9302a() ||
+	    machine_is_edb9302a() ||
+	    machine_is_edb9307() ||
+	    machine_is_edb9307a() ||
+	    machine_is_edb9307a() ||
+	    machine_is_edb9312() ||
+	    machine_is_edb9315() ||
+	    machine_is_edb9315a() ||
+	    machine_is_edb9315a() ||
+	    machine_is_ts72xx() ||
+	    machine_is_bk3() ||
+	    machine_is_vision_ep9307())
+		ep93xx_ethernet_reset();
 }
diff --git a/arch/arm/boot/compressed/misc.c b/arch/arm/boot/compressed/misc.c
index c3c66ff2d696..6c41b270560e 100644
--- a/arch/arm/boot/compressed/misc.c
+++ b/arch/arm/boot/compressed/misc.c
@@ -23,6 +23,9 @@ unsigned int __machine_arch_type;
 #include <linux/types.h>
 #include <linux/linkage.h>
 #include "misc.h"
+#ifdef CONFIG_ARCH_EP93XX
+#include "misc-ep93xx.h"
+#endif
 
 static void putstr(const char *ptr);
 
@@ -100,9 +103,6 @@ static void putstr(const char *ptr)
 /*
  * gzip declarations
  */
-extern char input_data[];
-extern char input_data_end[];
-
 unsigned char *output_data;
 
 unsigned long free_mem_ptr;
@@ -128,9 +128,6 @@ asmlinkage void __div0(void)
 	error("Attempting division by 0!");
 }
 
-extern int do_decompress(u8 *input, int len, u8 *output, void (*error)(char *x));
-
-
 void
 decompress_kernel(unsigned long output_start, unsigned long free_mem_ptr_p,
 		unsigned long free_mem_ptr_end_p,
@@ -143,6 +140,9 @@ decompress_kernel(unsigned long output_start, unsigned long free_mem_ptr_p,
 	free_mem_end_ptr	= free_mem_ptr_end_p;
 	__machine_arch_type	= arch_id;
 
+#ifdef CONFIG_ARCH_EP93XX
+	ep93xx_decomp_setup();
+#endif
 	arch_decomp_setup();
 
 	putstr("Uncompressing Linux...");
@@ -154,7 +154,7 @@ decompress_kernel(unsigned long output_start, unsigned long free_mem_ptr_p,
 		putstr(" done, booting the kernel.\n");
 }
 
-void fortify_panic(const char *name)
+void __fortify_panic(const u8 reason, size_t avail, size_t size)
 {
 	error("detected buffer overflow");
 }
diff --git a/arch/arm/boot/compressed/misc.h b/arch/arm/boot/compressed/misc.h
index c958dccd1d97..8c73940b5fe4 100644
--- a/arch/arm/boot/compressed/misc.h
+++ b/arch/arm/boot/compressed/misc.h
@@ -6,5 +6,16 @@
 void error(char *x) __noreturn;
 extern unsigned long free_mem_ptr;
 extern unsigned long free_mem_end_ptr;
+void __div0(void);
+void
+decompress_kernel(unsigned long output_start, unsigned long free_mem_ptr_p,
+		  unsigned long free_mem_ptr_end_p, int arch_id);
+void __fortify_panic(const u8 reason, size_t avail, size_t size);
+int atags_to_fdt(void *atag_list, void *fdt, int total_space);
+uint32_t fdt_check_mem_start(uint32_t mem_start, const void *fdt);
+int do_decompress(u8 *input, int len, u8 *output, void (*error)(char *x));
+
+extern char input_data[];
+extern char input_data_end[];
 
 #endif
diff --git a/arch/arm/boot/compressed/vmlinux.lds.S b/arch/arm/boot/compressed/vmlinux.lds.S
index 1bcb68ac4b01..d411abd4310e 100644
--- a/arch/arm/boot/compressed/vmlinux.lds.S
+++ b/arch/arm/boot/compressed/vmlinux.lds.S
@@ -23,6 +23,7 @@ SECTIONS
     *(.ARM.extab*)
     *(.note.*)
     *(.rel.*)
+    *(.printk_index)
     /*
      * Discard any r/w data - this produces a link error if we have any,
      * which is required for PIC decompression.  Local data generates
@@ -57,6 +58,7 @@ SECTIONS
     *(.rodata)
     *(.rodata.*)
     *(.data.rel.ro)
+    *(.data.rel.ro.*)
   }
   .piggydata : {
     *(.piggydata)
@@ -123,7 +125,7 @@ SECTIONS
 
   . = BSS_START;
   __bss_start = .;
-  .bss			: { *(.bss) }
+  .bss			: { *(.bss .bss.*) }
   _end = .;
 
   . = ALIGN(8);		/* the stack must be 64-bit aligned */
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 7c16f8a2b738..efe38eb25301 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1,1569 +1,41 @@
 # SPDX-License-Identifier: GPL-2.0
-dtb-$(CONFIG_ARCH_ALPINE) += \
-	alpine-db.dtb
-dtb-$(CONFIG_MACH_ARTPEC6) += \
-	artpec6-devboard.dtb
-dtb-$(CONFIG_MACH_ASM9260) += \
-	alphascale-asm9260-devkit.dtb
-# Keep at91 dtb files sorted alphabetically for each SoC
-dtb-$(CONFIG_SOC_AT91RM9200) += \
-	at91rm9200ek.dtb \
-	mpa1600.dtb
-dtb-$(CONFIG_SOC_AT91SAM9) += \
-	animeo_ip.dtb \
-	at91-qil_a9260.dtb \
-	aks-cdu.dtb \
-	ethernut5.dtb \
-	evk-pro3.dtb \
-	tny_a9260.dtb \
-	usb_a9260.dtb \
-	at91sam9260ek.dtb \
-	at91sam9261ek.dtb \
-	at91sam9263ek.dtb \
-	at91-sam9_l9260.dtb \
-	tny_a9263.dtb \
-	usb_a9263.dtb \
-	at91-foxg20.dtb \
-	at91-kizbox.dtb \
-	at91-lmu5000.dtb \
-	at91sam9g20ek.dtb \
-	at91sam9g20ek_2mmc.dtb \
-	tny_a9g20.dtb \
-	usb_a9g20.dtb \
-	usb_a9g20_lpw.dtb \
-	at91sam9m10g45ek.dtb \
-	pm9g45.dtb \
-	at91sam9n12ek.dtb \
-	at91sam9rlek.dtb \
-	at91-ariag25.dtb \
-	at91-ariettag25.dtb \
-	at91-cosino_mega2560.dtb \
-	at91-kizboxmini-base.dtb \
-	at91-kizboxmini-mb.dtb \
-	at91-kizboxmini-rd.dtb \
-	at91-q5xr5.dtb \
-	at91-smartkiz.dtb \
-	at91-wb45n.dtb \
-	at91sam9g15ek.dtb \
-	at91sam9g25-gardena-smart-gateway.dtb \
-	at91sam9g25ek.dtb \
-	at91sam9g35ek.dtb \
-	at91sam9x25ek.dtb \
-	at91sam9x35ek.dtb
-dtb-$(CONFIG_SOC_SAM9X60) += \
-	at91-sam9x60ek.dtb
-dtb-$(CONFIG_SOC_SAM_V7) += \
-	at91-kizbox2-2.dtb \
-	at91-kizbox3-hs.dtb \
-	at91-nattis-2-natte-2.dtb \
-	at91-sama5d27_som1_ek.dtb \
-	at91-sama5d27_wlsom1_ek.dtb \
-	at91-sama5d2_icp.dtb \
-	at91-sama5d2_ptc_ek.dtb \
-	at91-sama5d2_xplained.dtb \
-	at91-sama5d3_ksz9477_evb.dtb \
-	at91-sama5d3_xplained.dtb \
-	at91-dvk_som60.dtb \
-	at91-gatwick.dtb \
-	at91-tse850-3.dtb \
-	at91-wb50n.dtb \
-	sama5d31ek.dtb \
-	sama5d33ek.dtb \
-	sama5d34ek.dtb \
-	sama5d35ek.dtb \
-	sama5d36ek.dtb \
-	sama5d36ek_cmp.dtb \
-	at91-sama5d4_ma5d4evk.dtb \
-	at91-sama5d4_xplained.dtb \
-	at91-sama5d4ek.dtb \
-	at91-vinco.dtb
-dtb-$(CONFIG_SOC_SAMA7G5) += \
-	at91-sama7g5ek.dtb
-dtb-$(CONFIG_ARCH_AXXIA) += \
-	axm5516-amarillo.dtb
-dtb-$(CONFIG_ARCH_BCM2835) += \
-	bcm2835-rpi-b.dtb \
-	bcm2835-rpi-a.dtb \
-	bcm2835-rpi-b-rev2.dtb \
-	bcm2835-rpi-b-plus.dtb \
-	bcm2835-rpi-a-plus.dtb \
-	bcm2835-rpi-cm1-io1.dtb \
-	bcm2836-rpi-2-b.dtb \
-	bcm2837-rpi-3-a-plus.dtb \
-	bcm2837-rpi-3-b.dtb \
-	bcm2837-rpi-3-b-plus.dtb \
-	bcm2837-rpi-cm3-io3.dtb \
-	bcm2837-rpi-zero-2-w.dtb \
-	bcm2711-rpi-400.dtb \
-	bcm2711-rpi-4-b.dtb \
-	bcm2711-rpi-cm4-io.dtb \
-	bcm2835-rpi-zero.dtb \
-	bcm2835-rpi-zero-w.dtb
-dtb-$(CONFIG_ARCH_BCM_5301X) += \
-	bcm4708-asus-rt-ac56u.dtb \
-	bcm4708-asus-rt-ac68u.dtb \
-	bcm4708-buffalo-wzr-1750dhp.dtb \
-	bcm4708-linksys-ea6300-v1.dtb \
-	bcm4708-linksys-ea6500-v2.dtb \
-	bcm4708-luxul-xap-1510.dtb \
-	bcm4708-luxul-xwc-1000.dtb \
-	bcm4708-netgear-r6250.dtb \
-	bcm4708-netgear-r6300-v2.dtb \
-	bcm4708-smartrg-sr400ac.dtb \
-	bcm47081-asus-rt-n18u.dtb \
-	bcm47081-buffalo-wzr-600dhp2.dtb \
-	bcm47081-buffalo-wzr-900dhp.dtb \
-	bcm47081-luxul-xap-1410.dtb \
-	bcm47081-luxul-xwr-1200.dtb \
-	bcm47081-tplink-archer-c5-v2.dtb \
-	bcm4709-asus-rt-ac87u.dtb \
-	bcm4709-buffalo-wxr-1900dhp.dtb \
-	bcm4709-linksys-ea9200.dtb \
-	bcm4709-netgear-r7000.dtb \
-	bcm4709-netgear-r8000.dtb \
-	bcm4709-tplink-archer-c9-v1.dtb \
-	bcm47094-asus-rt-ac88u.dtb \
-	bcm47094-dlink-dir-885l.dtb \
-	bcm47094-linksys-panamera.dtb \
-	bcm47094-luxul-abr-4500.dtb \
-	bcm47094-luxul-xap-1610.dtb \
-	bcm47094-luxul-xbr-4500.dtb \
-	bcm47094-luxul-xwc-2000.dtb \
-	bcm47094-luxul-xwr-3100.dtb \
-	bcm47094-luxul-xwr-3150-v1.dtb \
-	bcm47094-netgear-r8500.dtb \
-	bcm47094-phicomm-k3.dtb \
-	bcm53016-meraki-mr32.dtb \
-	bcm94708.dtb \
-	bcm94709.dtb \
-	bcm953012er.dtb \
-	bcm953012hr.dtb \
-	bcm953012k.dtb
-dtb-$(CONFIG_ARCH_BCM_53573) += \
-	bcm47189-luxul-xap-1440.dtb \
-	bcm47189-luxul-xap-810.dtb \
-	bcm47189-tenda-ac9.dtb \
-	bcm947189acdbmr.dtb
-dtb-$(CONFIG_ARCH_BCM_63XX) += \
-	bcm963138dvt.dtb
-dtb-$(CONFIG_ARCH_BCM_CYGNUS) += \
-	bcm911360_entphn.dtb \
-	bcm911360k.dtb \
-	bcm958300k.dtb \
-	bcm958305k.dtb
-dtb-$(CONFIG_ARCH_BCM_HR2) += \
-	bcm53340-ubnt-unifi-switch8.dtb
-dtb-$(CONFIG_ARCH_BCM_MOBILE) += \
-	bcm28155-ap.dtb \
-	bcm21664-garnet.dtb \
-	bcm23550-sparrow.dtb
-dtb-$(CONFIG_ARCH_BCM_NSP) += \
-	bcm958522er.dtb \
-	bcm958525er.dtb \
-	bcm958525xmc.dtb \
-	bcm958622hr.dtb \
-	bcm958623hr.dtb \
-	bcm958625-meraki-mx64.dtb \
-	bcm958625-meraki-mx64-a0.dtb \
-	bcm958625-meraki-mx64w.dtb \
-	bcm958625-meraki-mx64w-a0.dtb \
-	bcm958625-meraki-mx65.dtb \
-	bcm958625-meraki-mx65w.dtb \
-	bcm958625hr.dtb \
-	bcm988312hr.dtb \
-	bcm958625k.dtb
-dtb-$(CONFIG_ARCH_BERLIN) += \
-	berlin2-sony-nsz-gs7.dtb \
-	berlin2cd-google-chromecast.dtb \
-	berlin2cd-valve-steamlink.dtb \
-	berlin2q-marvell-dmp.dtb
-dtb-$(CONFIG_ARCH_BRCMSTB) += \
-	bcm7445-bcm97445svmb.dtb
-dtb-$(CONFIG_ARCH_CLPS711X) += \
-	ep7211-edb7211.dtb
-dtb-$(CONFIG_ARCH_DAVINCI) += \
-	da850-lcdk.dtb \
-	da850-enbw-cmc.dtb \
-	da850-evm.dtb \
-	da850-lego-ev3.dtb
-dtb-$(CONFIG_ARCH_DIGICOLOR) += \
-	cx92755_equinox.dtb
-dtb-$(CONFIG_ARCH_AIROHA) += \
-	en7523-evb.dtb
-dtb-$(CONFIG_ARCH_EXYNOS3) += \
-	exynos3250-artik5-eval.dtb \
-	exynos3250-monk.dtb \
-	exynos3250-rinato.dtb
-dtb-$(CONFIG_ARCH_EXYNOS4) += \
-	exynos4210-i9100.dtb \
-	exynos4210-origen.dtb \
-	exynos4210-smdkv310.dtb \
-	exynos4210-trats.dtb \
-	exynos4210-universal_c210.dtb \
-	exynos4412-i9300.dtb \
-	exynos4412-i9305.dtb \
-	exynos4412-itop-elite.dtb \
-	exynos4412-n710x.dtb \
-	exynos4412-odroidu3.dtb \
-	exynos4412-odroidx.dtb \
-	exynos4412-odroidx2.dtb \
-	exynos4412-origen.dtb \
-	exynos4412-p4note-n8010.dtb \
-	exynos4412-smdk4412.dtb \
-	exynos4412-tiny4412.dtb \
-	exynos4412-trats2.dtb
-dtb-$(CONFIG_ARCH_EXYNOS5) += \
-	exynos5250-arndale.dtb \
-	exynos5250-smdk5250.dtb \
-	exynos5250-snow.dtb \
-	exynos5250-snow-rev5.dtb \
-	exynos5250-spring.dtb \
-	exynos5260-xyref5260.dtb \
-	exynos5410-odroidxu.dtb \
-	exynos5410-smdk5410.dtb \
-	exynos5420-arndale-octa.dtb \
-	exynos5420-peach-pit.dtb \
-	exynos5420-smdk5420.dtb \
-	exynos5420-chagall-wifi.dtb \
-	exynos5420-klimt-wifi.dtb \
-	exynos5422-odroidhc1.dtb \
-	exynos5422-odroidxu3.dtb \
-	exynos5422-odroidxu3-lite.dtb \
-	exynos5422-odroidxu4.dtb \
-	exynos5800-peach-pi.dtb
-dtb-$(CONFIG_ARCH_GEMINI) += \
-	gemini-dlink-dir-685.dtb \
-	gemini-dlink-dns-313.dtb \
-	gemini-nas4220b.dtb \
-	gemini-ns2502.dtb \
-	gemini-rut1xx.dtb \
-	gemini-sl93512r.dtb \
-	gemini-sq201.dtb \
-	gemini-ssi1328.dtb \
-	gemini-wbd111.dtb \
-	gemini-wbd222.dtb
-dtb-$(CONFIG_ARCH_HI3xxx) += \
-	hi3620-hi4511.dtb
-dtb-$(CONFIG_ARCH_HIGHBANK) += \
-	highbank.dtb \
-	ecx-2000.dtb
-dtb-$(CONFIG_ARCH_HIP01) += \
-	hip01-ca9x2.dtb
-dtb-$(CONFIG_ARCH_HIP04) += \
-	hip04-d01.dtb
-dtb-$(CONFIG_ARCH_HISI) += \
-	hi3519-demb.dtb
-dtb-$(CONFIG_ARCH_HIX5HD2) += \
-	hisi-x5hd2-dkb.dtb
-dtb-$(CONFIG_ARCH_INTEGRATOR) += \
-	integratorap.dtb \
-	integratorap-im-pd1.dtb \
-	integratorcp.dtb
-dtb-$(CONFIG_ARCH_IXP4XX) += \
-	intel-ixp42x-linksys-nslu2.dtb \
-	intel-ixp42x-linksys-wrv54g.dtb \
-	intel-ixp42x-freecom-fsg-3.dtb \
-	intel-ixp42x-welltech-epbx100.dtb \
-	intel-ixp42x-ixdp425.dtb \
-	intel-ixp43x-kixrp435.dtb \
-	intel-ixp46x-ixdp465.dtb \
-	intel-ixp42x-adi-coyote.dtb \
-	intel-ixp42x-ixdpg425.dtb \
-	intel-ixp42x-goramo-multilink.dtb \
-	intel-ixp42x-iomega-nas100d.dtb \
-	intel-ixp42x-dlink-dsm-g600.dtb \
-	intel-ixp42x-gateworks-gw2348.dtb \
-	intel-ixp43x-gateworks-gw2358.dtb \
-	intel-ixp42x-netgear-wg302v1.dtb \
-	intel-ixp42x-arcom-vulcan.dtb \
-	intel-ixp42x-gateway-7001.dtb
-dtb-$(CONFIG_ARCH_KEYSTONE) += \
-	keystone-k2hk-evm.dtb \
-	keystone-k2l-evm.dtb \
-	keystone-k2e-evm.dtb \
-	keystone-k2g-evm.dtb \
-	keystone-k2g-ice.dtb
-dtb-$(CONFIG_MACH_KIRKWOOD) += \
-	kirkwood-b3.dtb \
-	kirkwood-blackarmor-nas220.dtb \
-	kirkwood-c200-v1.dtb \
-	kirkwood-cloudbox.dtb \
-	kirkwood-d2net.dtb \
-	kirkwood-db-88f6281.dtb \
-	kirkwood-db-88f6282.dtb \
-	kirkwood-dir665.dtb \
-	kirkwood-dns320.dtb \
-	kirkwood-dns325.dtb \
-	kirkwood-dockstar.dtb \
-	kirkwood-dreamplug.dtb \
-	kirkwood-ds109.dtb \
-	kirkwood-ds110jv10.dtb \
-	kirkwood-ds111.dtb \
-	kirkwood-ds112.dtb \
-	kirkwood-ds209.dtb \
-	kirkwood-ds210.dtb \
-	kirkwood-ds212.dtb \
-	kirkwood-ds212j.dtb \
-	kirkwood-ds409.dtb \
-	kirkwood-ds409slim.dtb \
-	kirkwood-ds411.dtb \
-	kirkwood-ds411j.dtb \
-	kirkwood-ds411slim.dtb \
-	kirkwood-goflexnet.dtb \
-	kirkwood-guruplug-server-plus.dtb \
-	kirkwood-ib62x0.dtb \
-	kirkwood-iconnect.dtb \
-	kirkwood-iomega_ix2_200.dtb \
-	kirkwood-is2.dtb \
-	kirkwood-km_kirkwood.dtb \
-	kirkwood-l-50.dtb \
-	kirkwood-laplug.dtb \
-	kirkwood-linkstation-lsqvl.dtb \
-	kirkwood-linkstation-lsvl.dtb \
-	kirkwood-linkstation-lswsxl.dtb \
-	kirkwood-linkstation-lswvl.dtb \
-	kirkwood-linkstation-lswxl.dtb \
-	kirkwood-linksys-viper.dtb \
-	kirkwood-lschlv2.dtb \
-	kirkwood-lsxhl.dtb \
-	kirkwood-mplcec4.dtb \
-	kirkwood-mv88f6281gtw-ge.dtb \
-	kirkwood-nas2big.dtb \
-	kirkwood-net2big.dtb \
-	kirkwood-net5big.dtb \
-	kirkwood-netgear_readynas_duo_v2.dtb \
-	kirkwood-netgear_readynas_nv+_v2.dtb \
-	kirkwood-ns2.dtb \
-	kirkwood-ns2lite.dtb \
-	kirkwood-ns2max.dtb \
-	kirkwood-ns2mini.dtb \
-	kirkwood-nsa310.dtb \
-	kirkwood-nsa310a.dtb \
-	kirkwood-nsa320.dtb \
-	kirkwood-nsa325.dtb \
-	kirkwood-openblocks_a6.dtb \
-	kirkwood-openblocks_a7.dtb \
-	kirkwood-openrd-base.dtb \
-	kirkwood-openrd-client.dtb \
-	kirkwood-openrd-ultimate.dtb \
-	kirkwood-pogo_e02.dtb \
-	kirkwood-pogoplug-series-4.dtb \
-	kirkwood-rd88f6192.dtb \
-	kirkwood-rd88f6281-z0.dtb \
-	kirkwood-rd88f6281-a.dtb \
-	kirkwood-rs212.dtb \
-	kirkwood-rs409.dtb \
-	kirkwood-rs411.dtb \
-	kirkwood-sheevaplug.dtb \
-	kirkwood-sheevaplug-esata.dtb \
-	kirkwood-t5325.dtb \
-	kirkwood-topkick.dtb \
-	kirkwood-ts219-6281.dtb \
-	kirkwood-ts219-6282.dtb \
-	kirkwood-ts419-6281.dtb \
-	kirkwood-ts419-6282.dtb
-dtb-$(CONFIG_ARCH_LPC18XX) += \
-	lpc4337-ciaa.dtb \
-	lpc4350-hitex-eval.dtb \
-	lpc4357-ea4357-devkit.dtb \
-	lpc4357-myd-lpc4357.dtb
-dtb-$(CONFIG_ARCH_LPC32XX) += \
-	lpc3250-ea3250.dtb \
-	lpc3250-phy3250.dtb
-dtb-$(CONFIG_ARCH_WPCM450) += \
-	nuvoton-wpcm450-supermicro-x9sci-ln4f.dtb
-dtb-$(CONFIG_ARCH_NPCM7XX) += \
-	nuvoton-npcm730-gsj.dtb \
-	nuvoton-npcm730-gbs.dtb \
-	nuvoton-npcm730-kudo.dtb \
-	nuvoton-npcm750-evb.dtb \
-	nuvoton-npcm750-runbmc-olympus.dtb
-dtb-$(CONFIG_MACH_MESON6) += \
-	meson6-atv1200.dtb
-dtb-$(CONFIG_MACH_MESON8) += \
-	meson8-minix-neo-x8.dtb \
-	meson8b-ec100.dtb \
-	meson8b-mxq.dtb \
-	meson8b-odroidc1.dtb \
-	meson8m2-mxiii-plus.dtb
-dtb-$(CONFIG_ARCH_MMP) += \
-	pxa168-aspenite.dtb \
-	pxa910-dkb.dtb \
-	mmp2-brownstone.dtb \
-	mmp2-olpc-xo-1-75.dtb \
-	mmp3-dell-ariel.dtb
-dtb-$(CONFIG_ARCH_MPS2) += \
-	mps2-an385.dtb \
-	mps2-an399.dtb
-dtb-$(CONFIG_ARCH_MOXART) += \
-	moxart-uc7112lx.dtb
-dtb-$(CONFIG_ARCH_SD5203) += \
-	sd5203.dtb
-dtb-$(CONFIG_SOC_IMX1) += \
-	imx1-ads.dtb \
-	imx1-apf9328.dtb
-dtb-$(CONFIG_SOC_IMX25) += \
-	imx25-eukrea-mbimxsd25-baseboard.dtb \
-	imx25-eukrea-mbimxsd25-baseboard-cmo-qvga.dtb \
-	imx25-eukrea-mbimxsd25-baseboard-dvi-svga.dtb \
-	imx25-eukrea-mbimxsd25-baseboard-dvi-vga.dtb \
-	imx25-karo-tx25.dtb \
-	imx25-pdk.dtb
-dtb-$(CONFIG_SOC_IMX27) += \
-	imx27-apf27.dtb \
-	imx27-apf27dev.dtb \
-	imx27-eukrea-mbimxsd27-baseboard.dtb \
-	imx27-pdk.dtb \
-	imx27-phytec-phycore-rdk.dtb \
-	imx27-phytec-phycard-s-rdk.dtb
-dtb-$(CONFIG_SOC_IMX31) += \
-	imx31-bug.dtb \
-	imx31-lite.dtb
-dtb-$(CONFIG_SOC_IMX35) += \
-	imx35-eukrea-mbimxsd35-baseboard.dtb \
-	imx35-pdk.dtb
-dtb-$(CONFIG_SOC_IMX50) += \
-	imx50-evk.dtb \
-	imx50-kobo-aura.dtb
-dtb-$(CONFIG_SOC_IMX51) += \
-	imx51-apf51.dtb \
-	imx51-apf51dev.dtb \
-	imx51-babbage.dtb \
-	imx51-digi-connectcore-jsk.dtb \
-	imx51-eukrea-mbimxsd51-baseboard.dtb \
-	imx51-ts4800.dtb \
-	imx51-zii-rdu1.dtb \
-	imx51-zii-scu2-mezz.dtb \
-	imx51-zii-scu3-esb.dtb
-dtb-$(CONFIG_SOC_IMX53) += \
-	imx53-ard.dtb \
-	imx53-cx9020.dtb \
-	imx53-kp-ddc.dtb \
-	imx53-kp-hsc.dtb \
-	imx53-m53evk.dtb \
-	imx53-m53menlo.dtb \
-	imx53-mba53.dtb \
-	imx53-ppd.dtb \
-	imx53-qsb.dtb \
-	imx53-qsrb.dtb \
-	imx53-smd.dtb \
-	imx53-tx53-x03x.dtb \
-	imx53-tx53-x13x.dtb \
-	imx53-usbarmory.dtb \
-	imx53-voipac-bsb.dtb
-dtb-$(CONFIG_SOC_IMX6Q) += \
-	imx6dl-alti6p.dtb \
-	imx6dl-apf6dev.dtb \
-	imx6dl-aristainetos_4.dtb \
-	imx6dl-aristainetos_7.dtb \
-	imx6dl-aristainetos2_4.dtb \
-	imx6dl-aristainetos2_7.dtb \
-	imx6dl-colibri-eval-v3.dtb \
-	imx6dl-colibri-v1_1-eval-v3.dtb \
-	imx6dl-cubox-i.dtb \
-	imx6dl-cubox-i-emmc-som-v15.dtb \
-	imx6dl-cubox-i-som-v15.dtb \
-	imx6dl-dfi-fs700-m60.dtb \
-	imx6dl-dhcom-picoitx.dtb \
-	imx6dl-eckelmann-ci4x10.dtb \
-	imx6dl-emcon-avari.dtb \
-	imx6dl-gw51xx.dtb \
-	imx6dl-gw52xx.dtb \
-	imx6dl-gw53xx.dtb \
-	imx6dl-gw54xx.dtb \
-	imx6dl-gw551x.dtb \
-	imx6dl-gw552x.dtb \
-	imx6dl-gw553x.dtb \
-	imx6dl-gw560x.dtb \
-	imx6dl-gw5903.dtb \
-	imx6dl-gw5904.dtb \
-	imx6dl-gw5907.dtb \
-	imx6dl-gw5910.dtb \
-	imx6dl-gw5912.dtb \
-	imx6dl-gw5913.dtb \
-	imx6dl-hummingboard.dtb \
-	imx6dl-hummingboard-emmc-som-v15.dtb \
-	imx6dl-hummingboard-som-v15.dtb \
-	imx6dl-hummingboard2.dtb \
-	imx6dl-hummingboard2-emmc-som-v15.dtb \
-	imx6dl-hummingboard2-som-v15.dtb \
-	imx6dl-icore.dtb \
-	imx6dl-icore-mipi.dtb \
-	imx6dl-icore-rqs.dtb \
-	imx6dl-lanmcu.dtb \
-	imx6dl-mamoj.dtb \
-	imx6dl-mba6a.dtb \
-	imx6dl-mba6b.dtb \
-	imx6dl-nit6xlite.dtb \
-	imx6dl-nitrogen6x.dtb \
-	imx6dl-phytec-mira-rdk-nand.dtb \
-	imx6dl-phytec-pbab01.dtb \
-	imx6dl-pico-dwarf.dtb \
-	imx6dl-pico-hobbit.dtb \
-	imx6dl-pico-nymph.dtb \
-	imx6dl-pico-pi.dtb \
-	imx6dl-plybas.dtb \
-	imx6dl-plym2m.dtb \
-	imx6dl-prtmvt.dtb \
-	imx6dl-prtrvt.dtb \
-	imx6dl-prtvt7.dtb \
-	imx6dl-rex-basic.dtb \
-	imx6dl-riotboard.dtb \
-	imx6dl-sabreauto.dtb \
-	imx6dl-sabrelite.dtb \
-	imx6dl-sabresd.dtb \
-	imx6dl-savageboard.dtb \
-	imx6dl-skov-revc-lt2.dtb \
-	imx6dl-skov-revc-lt6.dtb \
-	imx6dl-solidsense.dtb \
-	imx6dl-ts4900.dtb \
-	imx6dl-ts7970.dtb \
-	imx6dl-tx6dl-comtft.dtb \
-	imx6dl-tx6s-8034.dtb \
-	imx6dl-tx6s-8034-mb7.dtb \
-	imx6dl-tx6s-8035.dtb \
-	imx6dl-tx6s-8035-mb7.dtb \
-	imx6dl-tx6u-801x.dtb \
-	imx6dl-tx6u-80xx-mb7.dtb \
-	imx6dl-tx6u-8033.dtb \
-	imx6dl-tx6u-8033-mb7.dtb \
-	imx6dl-tx6u-811x.dtb \
-	imx6dl-tx6u-81xx-mb7.dtb \
-	imx6dl-udoo.dtb \
-	imx6dl-victgo.dtb \
-	imx6dl-vicut1.dtb \
-	imx6dl-wandboard.dtb \
-	imx6dl-wandboard-revb1.dtb \
-	imx6dl-wandboard-revd1.dtb \
-	imx6dl-yapp4-draco.dtb \
-	imx6dl-yapp4-hydra.dtb \
-	imx6dl-yapp4-orion.dtb \
-	imx6dl-yapp4-ursa.dtb \
-	imx6q-apalis-eval.dtb \
-	imx6q-apalis-ixora.dtb \
-	imx6q-apalis-ixora-v1.1.dtb \
-	imx6q-apf6dev.dtb \
-	imx6q-arm2.dtb \
-	imx6q-b450v3.dtb \
-	imx6q-b650v3.dtb \
-	imx6q-b850v3.dtb \
-	imx6q-cm-fx6.dtb \
-	imx6q-cubox-i.dtb \
-	imx6q-cubox-i-emmc-som-v15.dtb \
-	imx6q-cubox-i-som-v15.dtb \
-	imx6q-dfi-fs700-m60.dtb \
-	imx6q-dhcom-pdk2.dtb \
-	imx6q-display5-tianma-tm070-1280x768.dtb \
-	imx6q-dmo-edmqmx6.dtb \
-	imx6q-dms-ba16.dtb \
-	imx6q-ds.dtb \
-	imx6q-emcon-avari.dtb \
-	imx6q-evi.dtb \
-	imx6dl-b105pv2.dtb \
-	imx6dl-b105v2.dtb \
-	imx6dl-b125v2.dtb \
-	imx6dl-b125pv2.dtb \
-	imx6dl-b155v2.dtb \
-	imx6q-gk802.dtb \
-	imx6q-gw51xx.dtb \
-	imx6q-gw52xx.dtb \
-	imx6q-gw53xx.dtb \
-	imx6q-gw5400-a.dtb \
-	imx6q-gw54xx.dtb \
-	imx6q-gw551x.dtb \
-	imx6q-gw552x.dtb \
-	imx6q-gw553x.dtb \
-	imx6q-gw560x.dtb \
-	imx6q-gw5903.dtb \
-	imx6q-gw5904.dtb \
-	imx6q-gw5907.dtb \
-	imx6q-gw5910.dtb \
-	imx6q-gw5912.dtb \
-	imx6q-gw5913.dtb \
-	imx6q-h100.dtb \
-	imx6q-hummingboard.dtb \
-	imx6q-hummingboard-emmc-som-v15.dtb \
-	imx6q-hummingboard-som-v15.dtb \
-	imx6q-hummingboard2.dtb \
-	imx6q-hummingboard2-emmc-som-v15.dtb \
-	imx6q-hummingboard2-som-v15.dtb \
-	imx6q-icore.dtb \
-	imx6q-icore-mipi.dtb \
-	imx6q-icore-ofcap10.dtb \
-	imx6q-icore-ofcap12.dtb \
-	imx6q-icore-rqs.dtb \
-	imx6q-kp-tpc.dtb \
-	imx6q-logicpd.dtb \
-	imx6q-marsboard.dtb \
-	imx6q-mba6a.dtb \
-	imx6q-mba6b.dtb \
-	imx6q-mccmon6.dtb \
-	imx6q-nitrogen6x.dtb \
-	imx6q-nitrogen6_max.dtb \
-	imx6q-nitrogen6_som2.dtb \
-	imx6q-novena.dtb \
-	imx6q-phytec-mira-rdk-emmc.dtb \
-	imx6q-phytec-mira-rdk-nand.dtb \
-	imx6q-phytec-pbab01.dtb \
-	imx6q-pico-dwarf.dtb \
-	imx6q-pico-hobbit.dtb \
-	imx6q-pico-nymph.dtb \
-	imx6q-pico-pi.dtb \
-	imx6q-pistachio.dtb \
-	imx6q-prti6q.dtb \
-	imx6q-prtwd2.dtb \
-	imx6q-rex-pro.dtb \
-	imx6q-sabreauto.dtb \
-	imx6q-sabrelite.dtb \
-	imx6q-sabresd.dtb \
-	imx6q-savageboard.dtb \
-	imx6q-sbc6x.dtb \
-	imx6q-skov-revc-lt2.dtb \
-	imx6q-skov-revc-lt6.dtb \
-	imx6q-skov-reve-mi1010ait-1cp1.dtb \
-	imx6q-solidsense.dtb \
-	imx6q-tbs2910.dtb \
-	imx6q-ts4900.dtb \
-	imx6q-ts7970.dtb \
-	imx6q-tx6q-1010.dtb \
-	imx6q-tx6q-1010-comtft.dtb \
-	imx6q-tx6q-1020.dtb \
-	imx6q-tx6q-1020-comtft.dtb \
-	imx6q-tx6q-1036.dtb \
-	imx6q-tx6q-1036-mb7.dtb \
-	imx6q-tx6q-10x0-mb7.dtb \
-	imx6q-tx6q-1110.dtb \
-	imx6q-tx6q-11x0-mb7.dtb \
-	imx6q-udoo.dtb \
-	imx6q-utilite-pro.dtb \
-	imx6q-var-dt6customboard.dtb \
-	imx6q-vicut1.dtb \
-	imx6q-wandboard.dtb \
-	imx6q-wandboard-revb1.dtb \
-	imx6q-wandboard-revd1.dtb \
-	imx6q-yapp4-crux.dtb \
-	imx6q-zii-rdu2.dtb \
-	imx6qp-mba6b.dtb \
-	imx6qp-nitrogen6_max.dtb \
-	imx6qp-nitrogen6_som2.dtb \
-	imx6qp-phytec-mira-rdk-nand.dtb \
-	imx6qp-prtwd3.dtb \
-	imx6qp-sabreauto.dtb \
-	imx6qp-sabresd.dtb \
-	imx6qp-tx6qp-8037.dtb \
-	imx6qp-tx6qp-8037-mb7.dtb \
-	imx6qp-tx6qp-8137.dtb \
-	imx6qp-tx6qp-8137-mb7.dtb \
-	imx6qp-vicutp.dtb \
-	imx6qp-wandboard-revd1.dtb \
-	imx6qp-yapp4-crux-plus.dtb \
-	imx6qp-zii-rdu2.dtb \
-	imx6s-dhcom-drc02.dtb
-dtb-$(CONFIG_SOC_IMX6SL) += \
-	imx6sl-evk.dtb \
-	imx6sl-tolino-shine2hd.dtb \
-	imx6sl-tolino-shine3.dtb \
-	imx6sl-tolino-vision5.dtb \
-	imx6sl-warp.dtb
-dtb-$(CONFIG_SOC_IMX6SLL) += \
-	imx6sll-evk.dtb \
-	imx6sll-kobo-clarahd.dtb \
-	imx6sll-kobo-librah2o.dtb
-dtb-$(CONFIG_SOC_IMX6SX) += \
-	imx6sx-nitrogen6sx.dtb \
-	imx6sx-sabreauto.dtb \
-	imx6sx-sdb-reva.dtb \
-	imx6sx-sdb-sai.dtb \
-	imx6sx-sdb.dtb \
-	imx6sx-sdb-mqs.dtb \
-	imx6sx-softing-vining-2000.dtb \
-	imx6sx-udoo-neo-basic.dtb \
-	imx6sx-udoo-neo-extended.dtb \
-	imx6sx-udoo-neo-full.dtb
-dtb-$(CONFIG_SOC_IMX6UL) += \
-	imx6ul-14x14-evk.dtb \
-	imx6ul-ccimx6ulsbcexpress.dtb \
-	imx6ul-ccimx6ulsbcpro.dtb \
-	imx6ul-geam.dtb \
-	imx6ul-isiot-emmc.dtb \
-	imx6ul-isiot-nand.dtb \
-	imx6ul-kontron-n6310-s.dtb \
-	imx6ul-kontron-n6310-s-43.dtb \
-	imx6ul-liteboard.dtb \
-	imx6ul-opos6uldev.dtb \
-	imx6ul-pico-dwarf.dtb \
-	imx6ul-pico-hobbit.dtb \
-	imx6ul-pico-pi.dtb \
-	imx6ul-phytec-segin-ff-rdk-emmc.dtb \
-	imx6ul-phytec-segin-ff-rdk-nand.dtb \
-	imx6ul-prti6g.dtb \
-	imx6ul-tx6ul-0010.dtb \
-	imx6ul-tx6ul-0011.dtb \
-	imx6ul-tx6ul-mainboard.dtb \
-	imx6ull-14x14-evk.dtb \
-	imx6ull-colibri-emmc-eval-v3.dtb \
-	imx6ull-colibri-eval-v3.dtb \
-	imx6ull-colibri-wifi-eval-v3.dtb \
-	imx6ull-jozacp.dtb \
-	imx6ull-myir-mys-6ulx-eval.dtb \
-	imx6ull-opos6uldev.dtb \
-	imx6ull-phytec-segin-ff-rdk-nand.dtb \
-	imx6ull-phytec-segin-ff-rdk-emmc.dtb \
-	imx6ull-phytec-segin-lc-rdk-nand.dtb \
-	imx6ulz-14x14-evk.dtb \
-	imx6ulz-bsh-smm-m2.dtb
-dtb-$(CONFIG_SOC_IMX7D) += \
-	imx7d-cl-som-imx7.dtb \
-	imx7d-colibri-aster.dtb \
-	imx7d-colibri-emmc-aster.dtb \
-	imx7d-colibri-emmc-eval-v3.dtb \
-	imx7d-colibri-eval-v3.dtb \
-	imx7d-flex-concentrator.dtb \
-	imx7d-flex-concentrator-mfg.dtb \
-	imx7d-mba7.dtb \
-	imx7d-meerkat96.dtb \
-	imx7d-nitrogen7.dtb \
-	imx7d-pico-dwarf.dtb \
-	imx7d-pico-hobbit.dtb \
-	imx7d-pico-nymph.dtb \
-	imx7d-pico-pi.dtb \
-	imx7d-remarkable2.dtb \
-	imx7d-sbc-imx7.dtb \
-	imx7d-sdb.dtb \
-	imx7d-sdb-reva.dtb \
-	imx7d-sdb-sht11.dtb \
-	imx7d-zii-rmu2.dtb \
-	imx7d-zii-rpu2.dtb \
-	imx7s-colibri-aster.dtb \
-	imx7s-colibri-eval-v3.dtb \
-	imx7s-mba7.dtb \
-	imx7s-warp.dtb
-dtb-$(CONFIG_SOC_IMX7ULP) += \
-	imx7ulp-com.dtb \
-	imx7ulp-evk.dtb
-dtb-$(CONFIG_SOC_LAN966) += \
-	lan966x-pcb8291.dtb
-dtb-$(CONFIG_SOC_LS1021A) += \
-	ls1021a-moxa-uc-8410a.dtb \
-	ls1021a-qds.dtb \
-	ls1021a-tsn.dtb \
-	ls1021a-twr.dtb
-dtb-$(CONFIG_SOC_VF610) += \
-	vf500-colibri-eval-v3.dtb \
-	vf610-bk4.dtb \
-	vf610-colibri-eval-v3.dtb \
-	vf610m4-colibri.dtb \
-	vf610-cosmic.dtb \
-	vf610m4-cosmic.dtb \
-	vf610-twr.dtb \
-	vf610-zii-cfu1.dtb \
-	vf610-zii-dev-rev-b.dtb \
-	vf610-zii-dev-rev-c.dtb \
-	vf610-zii-scu4-aib.dtb \
-	vf610-zii-spb4.dtb \
-	vf610-zii-ssmb-dtu.dtb \
-	vf610-zii-ssmb-spu3.dtb
-dtb-$(CONFIG_ARCH_MXS) += \
-	imx23-evk.dtb \
-	imx23-olinuxino.dtb \
-	imx23-sansa.dtb \
-	imx23-stmp378x_devb.dtb \
-	imx23-xfi3.dtb \
-	imx28-apf28.dtb \
-	imx28-apf28dev.dtb \
-	imx28-apx4devkit.dtb \
-	imx28-cfa10036.dtb \
-	imx28-cfa10037.dtb \
-	imx28-cfa10049.dtb \
-	imx28-cfa10055.dtb \
-	imx28-cfa10056.dtb \
-	imx28-cfa10057.dtb \
-	imx28-cfa10058.dtb \
-	imx28-duckbill-2-485.dtb \
-	imx28-duckbill-2.dtb \
-	imx28-duckbill-2-enocean.dtb \
-	imx28-duckbill-2-spi.dtb \
-	imx28-duckbill.dtb \
-	imx28-eukrea-mbmx283lc.dtb \
-	imx28-eukrea-mbmx287lc.dtb \
-	imx28-evk.dtb \
-	imx28-m28cu3.dtb \
-	imx28-m28evk.dtb \
-	imx28-sps1.dtb \
-	imx28-ts4600.dtb \
-	imx28-tx28.dtb \
-	imx28-xea.dtb
-dtb-$(CONFIG_ARCH_NOMADIK) += \
-	ste-nomadik-s8815.dtb \
-	ste-nomadik-nhk15.dtb
-dtb-$(CONFIG_ARCH_NSPIRE) += \
-	nspire-cx.dtb \
-	nspire-tp.dtb \
-	nspire-clp.dtb
-dtb-$(CONFIG_ARCH_OMAP2) += \
-	omap2420-h4.dtb \
-	omap2420-n800.dtb \
-	omap2420-n810.dtb \
-	omap2420-n810-wimax.dtb \
-	omap2430-sdp.dtb
-dtb-$(CONFIG_ARCH_OMAP3) += \
-	am3517-craneboard.dtb \
-	am3517-evm.dtb \
-	am3517_mt_ventoux.dtb \
-	logicpd-torpedo-37xx-devkit.dtb \
-	logicpd-som-lv-37xx-devkit.dtb \
-	omap3430-sdp.dtb \
-	omap3-beagle.dtb \
-	omap3-beagle-ab4.dtb \
-	omap3-beagle-xm.dtb \
-	omap3-beagle-xm-ab.dtb \
-	omap3-cm-t3517.dtb \
-	omap3-cm-t3530.dtb \
-	omap3-cm-t3730.dtb \
-	omap3-devkit8000.dtb \
-	omap3-devkit8000-lcd43.dtb \
-	omap3-devkit8000-lcd70.dtb \
-	omap3-echo.dtb \
-	omap3-evm.dtb \
-	omap3-evm-37xx.dtb \
-	omap3-gta04a3.dtb \
-	omap3-gta04a4.dtb \
-	omap3-gta04a5.dtb \
-	omap3-gta04a5one.dtb \
-	omap3-ha.dtb \
-	omap3-ha-lcd.dtb \
-	omap3-igep0020.dtb \
-	omap3-igep0020-rev-f.dtb \
-	omap3-igep0030.dtb \
-	omap3-igep0030-rev-g.dtb \
-	omap3-ldp.dtb \
-	omap3-lilly-dbb056.dtb \
-	omap3-n900.dtb \
-	omap3-n9.dtb \
-	omap3-n950.dtb \
-	omap3-overo-alto35.dtb \
-	omap3-overo-chestnut43.dtb \
-	omap3-overo-gallop43.dtb \
-	omap3-overo-palo35.dtb \
-	omap3-overo-palo43.dtb \
-	omap3-overo-storm-alto35.dtb \
-	omap3-overo-storm-chestnut43.dtb \
-	omap3-overo-storm-gallop43.dtb \
-	omap3-overo-storm-palo35.dtb \
-	omap3-overo-storm-palo43.dtb \
-	omap3-overo-storm-summit.dtb \
-	omap3-overo-storm-tobi.dtb \
-	omap3-overo-storm-tobiduo.dtb \
-	omap3-overo-summit.dtb \
-	omap3-overo-tobi.dtb \
-	omap3-overo-tobiduo.dtb \
-	omap3-pandora-600mhz.dtb \
-	omap3-pandora-1ghz.dtb \
-	omap3-sbc-t3517.dtb \
-	omap3-sbc-t3530.dtb \
-	omap3-sbc-t3730.dtb \
-	omap3-sniper.dtb \
-	omap3-thunder.dtb \
-	omap3-zoom3.dtb
-dtb-$(CONFIG_SOC_TI81XX) += \
-	am3874-iceboard.dtb \
-	dm8148-evm.dtb \
-	dm8148-t410.dtb \
-	dm8168-evm.dtb \
-	dra62x-j5eco-evm.dtb
-dtb-$(CONFIG_SOC_AM33XX) += \
-	am335x-baltos-ir2110.dtb \
-	am335x-baltos-ir3220.dtb \
-	am335x-baltos-ir5221.dtb \
-	am335x-base0033.dtb \
-	am335x-bone.dtb \
-	am335x-boneblack.dtb \
-	am335x-boneblack-wireless.dtb \
-	am335x-boneblue.dtb \
-	am335x-bonegreen.dtb \
-	am335x-bonegreen-wireless.dtb \
-	am335x-chiliboard.dtb \
-	am335x-cm-t335.dtb \
-	am335x-evm.dtb \
-	am335x-evmsk.dtb \
-	am335x-guardian.dtb \
-	am335x-icev2.dtb \
-	am335x-lxm.dtb \
-	am335x-moxa-uc-2101.dtb \
-	am335x-moxa-uc-8100-me-t.dtb \
-	am335x-myirtech-myd.dtb \
-	am335x-nano.dtb \
-	am335x-netcan-plus-1xx.dtb \
-	am335x-netcom-plus-2xx.dtb \
-	am335x-netcom-plus-8xx.dtb \
-	am335x-pdu001.dtb \
-	am335x-pepper.dtb \
-	am335x-phycore-rdk.dtb \
-	am335x-pocketbeagle.dtb \
-	am335x-regor-rdk.dtb \
-	am335x-sancloud-bbe.dtb \
-	am335x-sancloud-bbe-lite.dtb \
-	am335x-sancloud-bbe-extended-wifi.dtb \
-	am335x-shc.dtb \
-	am335x-sbc-t335.dtb \
-	am335x-sl50.dtb \
-	am335x-wega-rdk.dtb \
-	am335x-osd3358-sm-red.dtb
-dtb-$(CONFIG_ARCH_OMAP4) += \
-	omap4-droid-bionic-xt875.dtb \
-	omap4-droid4-xt894.dtb \
-	omap4-duovero-parlor.dtb \
-	omap4-kc1.dtb \
-	omap4-panda.dtb \
-	omap4-panda-a4.dtb \
-	omap4-panda-es.dtb \
-	omap4-sdp.dtb \
-	omap4-sdp-es23plus.dtb \
-	omap4-var-dvk-om44.dtb \
-	omap4-var-stk-om44.dtb
-dtb-$(CONFIG_SOC_AM43XX) += \
-	am43x-epos-evm.dtb \
-	am437x-cm-t43.dtb \
-	am437x-gp-evm.dtb \
-	am437x-idk-evm.dtb \
-	am437x-sbc-t43.dtb \
-	am437x-sk-evm.dtb
-dtb-$(CONFIG_SOC_OMAP5) += \
-	omap5-cm-t54.dtb \
-	omap5-igep0050.dtb \
-	omap5-sbc-t54.dtb \
-	omap5-uevm.dtb
-dtb-$(CONFIG_SOC_DRA7XX) += \
-	am57xx-beagle-x15.dtb \
-	am57xx-beagle-x15-revb1.dtb \
-	am57xx-beagle-x15-revc.dtb \
-	am5729-beagleboneai.dtb \
-	am57xx-cl-som-am57x.dtb \
-	am57xx-sbc-am57x.dtb \
-	am572x-idk.dtb \
-	am571x-idk.dtb \
-	am574x-idk.dtb \
-	dra7-evm.dtb \
-	dra72-evm.dtb \
-	dra72-evm-revc.dtb \
-	dra71-evm.dtb \
-	dra76-evm.dtb
-dtb-$(CONFIG_ARCH_ORION5X) += \
-	orion5x-kuroboxpro.dtb \
-	orion5x-lacie-d2-network.dtb \
-	orion5x-lacie-ethernet-disk-mini-v2.dtb \
-	orion5x-linkstation-lsgl.dtb \
-	orion5x-linkstation-lswtgl.dtb \
-	orion5x-linkstation-lschl.dtb \
-	orion5x-lswsgl.dtb \
-	orion5x-maxtor-shared-storage-2.dtb \
-	orion5x-netgear-wnr854t.dtb \
-	orion5x-rd88f5182-nas.dtb
-dtb-$(CONFIG_ARCH_ACTIONS) += \
-	owl-s500-cubieboard6.dtb \
-	owl-s500-guitar-bb-rev-b.dtb \
-	owl-s500-labrador-base-m.dtb \
-	owl-s500-roseapplepi.dtb \
-	owl-s500-sparky.dtb
-dtb-$(CONFIG_ARCH_PXA) += \
-	pxa300-raumfeld-connector.dtb \
-	pxa300-raumfeld-controller.dtb \
-	pxa300-raumfeld-speaker-l.dtb \
-	pxa300-raumfeld-speaker-m.dtb \
-	pxa300-raumfeld-speaker-one.dtb \
-	pxa300-raumfeld-speaker-s.dtb
-dtb-$(CONFIG_ARCH_OXNAS) += \
-	ox810se-wd-mbwe.dtb \
-	ox820-cloudengines-pogoplug-series-3.dtb
-dtb-$(CONFIG_ARCH_QCOM) += \
-	qcom-apq8016-sbc.dtb \
-	qcom-apq8026-lg-lenok.dtb \
-	qcom-apq8060-dragonboard.dtb \
-	qcom-apq8064-cm-qs600.dtb \
-	qcom-apq8064-ifc6410.dtb \
-	qcom-apq8064-sony-xperia-yuga.dtb \
-	qcom-apq8064-asus-nexus7-flo.dtb \
-	qcom-apq8074-dragonboard.dtb \
-	qcom-apq8084-ifc6540.dtb \
-	qcom-apq8084-mtp.dtb \
-	qcom-ipq4018-ap120c-ac.dtb \
-	qcom-ipq4018-ap120c-ac-bit.dtb \
-	qcom-ipq4018-jalapeno.dtb \
-	qcom-ipq4019-ap.dk01.1-c1.dtb \
-	qcom-ipq4019-ap.dk04.1-c1.dtb \
-	qcom-ipq4019-ap.dk04.1-c3.dtb \
-	qcom-ipq4019-ap.dk07.1-c1.dtb \
-	qcom-ipq4019-ap.dk07.1-c2.dtb \
-	qcom-ipq8064-ap148.dtb \
-	qcom-ipq8064-rb3011.dtb \
-	qcom-msm8226-samsung-s3ve3g.dtb \
-	qcom-msm8660-surf.dtb \
-	qcom-msm8916-samsung-serranove.dtb \
-	qcom-msm8960-cdp.dtb \
-	qcom-msm8974-fairphone-fp2.dtb \
-	qcom-msm8974-lge-nexus5-hammerhead.dtb \
-	qcom-msm8974-samsung-klte.dtb \
-	qcom-msm8974-sony-xperia-amami.dtb \
-	qcom-msm8974-sony-xperia-castor.dtb \
-	qcom-msm8974-sony-xperia-honami.dtb \
-	qcom-mdm9615-wp8548-mangoh-green.dtb \
-	qcom-sdx55-mtp.dtb \
-	qcom-sdx55-t55.dtb \
-	qcom-sdx55-telit-fn980-tlb.dtb \
-	qcom-sdx65-mtp.dtb
-dtb-$(CONFIG_ARCH_RDA) += \
-	rda8810pl-orangepi-2g-iot.dtb \
-	rda8810pl-orangepi-i96.dtb
-dtb-$(CONFIG_ARCH_REALTEK) += \
-	rtd1195-horseradish.dtb \
-	rtd1195-mele-x1000.dtb
-dtb-$(CONFIG_ARCH_REALVIEW) += \
-	arm-realview-pb1176.dtb \
-	arm-realview-pb11mp.dtb \
-	arm-realview-eb.dtb \
-	arm-realview-eb-bbrevd.dtb \
-	arm-realview-eb-11mp.dtb \
-	arm-realview-eb-11mp-bbrevd.dtb \
-	arm-realview-eb-11mp-ctrevb.dtb \
-	arm-realview-eb-11mp-bbrevd-ctrevb.dtb \
-	arm-realview-eb-a9mp.dtb \
-	arm-realview-eb-a9mp-bbrevd.dtb \
-	arm-realview-pba8.dtb \
-	arm-realview-pbx-a9.dtb
-dtb-$(CONFIG_ARCH_RENESAS) += \
-	emev2-kzm9d.dtb \
-	r7s72100-genmai.dtb \
-	r7s72100-gr-peach.dtb \
-	r7s72100-rskrza1.dtb \
-	r7s9210-rza2mevb.dtb \
-	r8a73a4-ape6evm.dtb \
-	r8a7740-armadillo800eva.dtb \
-	r8a7742-iwg21d-q7.dtb \
-	r8a7742-iwg21d-q7-dbcm-ca.dtb \
-	r8a7743-iwg20d-q7.dtb \
-	r8a7743-iwg20d-q7-dbcm-ca.dtb \
-	r8a7743-sk-rzg1m.dtb \
-	r8a7744-iwg20d-q7.dtb \
-	r8a7744-iwg20d-q7-dbcm-ca.dtb \
-	r8a7745-iwg22d-sodimm.dtb \
-	r8a7745-iwg22d-sodimm-dbhd-ca.dtb \
-	r8a7745-sk-rzg1e.dtb \
-	r8a77470-iwg23s-sbc.dtb \
-	r8a7778-bockw.dtb \
-	r8a7779-marzen.dtb \
-	r8a7790-lager.dtb \
-	r8a7790-stout.dtb \
-	r8a7791-koelsch.dtb \
-	r8a7791-porter.dtb \
-	r8a7792-blanche.dtb \
-	r8a7792-wheat.dtb \
-	r8a7793-gose.dtb \
-	r8a7794-alt.dtb \
-	r8a7794-silk.dtb \
-	r9a06g032-rzn1d400-db.dtb \
-	sh73a0-kzm9g.dtb
-dtb-$(CONFIG_ARCH_ROCKCHIP) += \
-	rv1108-elgin-r1.dtb \
-	rv1108-evb.dtb \
-	rk3036-evb.dtb \
-	rk3036-kylin.dtb \
-	rk3066a-bqcurie2.dtb \
-	rk3066a-marsboard.dtb \
-	rk3066a-mk808.dtb \
-	rk3066a-rayeager.dtb \
-	rk3188-bqedison2qc.dtb \
-	rk3188-px3-evb.dtb \
-	rk3188-radxarock.dtb \
-	rk3228-evb.dtb \
-	rk3229-evb.dtb \
-	rk3229-xms6.dtb \
-	rk3288-evb-act8846.dtb \
-	rk3288-evb-rk808.dtb \
-	rk3288-firefly-beta.dtb \
-	rk3288-firefly.dtb \
-	rk3288-firefly-reload.dtb \
-	rk3288-miqi.dtb \
-	rk3288-phycore-rdk.dtb \
-	rk3288-popmetal.dtb \
-	rk3288-r89.dtb \
-	rk3288-rock2-square.dtb \
-	rk3288-rock-pi-n8.dtb \
-	rk3288-tinker.dtb \
-	rk3288-tinker-s.dtb \
-	rk3288-veyron-brain.dtb \
-	rk3288-veyron-fievel.dtb \
-	rk3288-veyron-jaq.dtb \
-	rk3288-veyron-jerry.dtb \
-	rk3288-veyron-mickey.dtb \
-	rk3288-veyron-mighty.dtb \
-	rk3288-veyron-minnie.dtb \
-	rk3288-veyron-pinky.dtb \
-	rk3288-veyron-speedy.dtb \
-	rk3288-veyron-tiger.dtb \
-	rk3288-vyasa.dtb
-dtb-$(CONFIG_ARCH_S3C24XX) += \
-	s3c2416-smdk2416.dtb
-dtb-$(CONFIG_ARCH_S3C64XX) += \
-	s3c6410-mini6410.dtb \
-	s3c6410-smdk6410.dtb
-dtb-$(CONFIG_ARCH_S5PV210) += \
-	s5pv210-aquila.dtb \
-	s5pv210-fascinate4g.dtb \
-	s5pv210-galaxys.dtb \
-	s5pv210-goni.dtb \
-	s5pv210-smdkc110.dtb \
-	s5pv210-smdkv210.dtb \
-	s5pv210-torbreck.dtb
-dtb-$(CONFIG_ARCH_INTEL_SOCFPGA) += \
-	socfpga_arria5_socdk.dtb \
-	socfpga_arria10_mercury_aa1.dtb \
-	socfpga_arria10_socdk_nand.dtb \
-	socfpga_arria10_socdk_qspi.dtb \
-	socfpga_arria10_socdk_sdmmc.dtb \
-	socfpga_cyclone5_chameleon96.dtb \
-	socfpga_cyclone5_mcvevk.dtb \
-	socfpga_cyclone5_socdk.dtb \
-	socfpga_cyclone5_de0_nano_soc.dtb \
-	socfpga_cyclone5_sockit.dtb \
-	socfpga_cyclone5_socrates.dtb \
-	socfpga_cyclone5_sodia.dtb \
-	socfpga_cyclone5_vining_fpga.dtb \
-	socfpga_vt.dtb
-dtb-$(CONFIG_ARCH_SPEAR13XX) += \
-	spear1310-evb.dtb \
-	spear1340-evb.dtb
-dtb-$(CONFIG_ARCH_SPEAR3XX) += \
-	spear300-evb.dtb \
-	spear310-evb.dtb \
-	spear320-evb.dtb \
-	spear320-hmi.dtb
-dtb-$(CONFIG_ARCH_SPEAR6XX) += \
-	spear600-evb.dtb
-dtb-$(CONFIG_ARCH_STI) += \
-	stih407-b2120.dtb \
-	stih410-b2120.dtb \
-	stih410-b2260.dtb \
-	stih418-b2199.dtb \
-	stih418-b2264.dtb
-dtb-$(CONFIG_ARCH_STM32) += \
-	stm32f429-disco.dtb \
-	stm32f469-disco.dtb \
-	stm32f746-disco.dtb \
-	stm32f769-disco.dtb \
-	stm32429i-eval.dtb \
-	stm32746g-eval.dtb \
-	stm32h743i-eval.dtb \
-	stm32h743i-disco.dtb \
-	stm32h750i-art-pi.dtb \
-	stm32mp135f-dk.dtb \
-	stm32mp153c-dhcom-drc02.dtb \
-	stm32mp157a-avenger96.dtb \
-	stm32mp157a-dhcor-avenger96.dtb \
-	stm32mp157a-dk1.dtb \
-	stm32mp157a-iot-box.dtb \
-	stm32mp157a-microgea-stm32mp1-microdev2.0.dtb \
-	stm32mp157a-microgea-stm32mp1-microdev2.0-of7.dtb \
-	stm32mp157a-icore-stm32mp1-ctouch2.dtb \
-	stm32mp157a-icore-stm32mp1-ctouch2-of10.dtb \
-	stm32mp157a-icore-stm32mp1-edimm2.2.dtb \
-	stm32mp157a-stinger96.dtb \
-	stm32mp157c-dhcom-pdk2.dtb \
-	stm32mp157c-dhcom-picoitx.dtb \
-	stm32mp157c-dk2.dtb \
-	stm32mp157c-ed1.dtb \
-	stm32mp157c-emsbc-argon.dtb \
-	stm32mp157c-ev1.dtb \
-	stm32mp157c-lxa-mc1.dtb \
-	stm32mp157c-odyssey.dtb
-dtb-$(CONFIG_MACH_SUN4I) += \
-	sun4i-a10-a1000.dtb \
-	sun4i-a10-ba10-tvbox.dtb \
-	sun4i-a10-chuwi-v7-cw0825.dtb \
-	sun4i-a10-cubieboard.dtb \
-	sun4i-a10-dserve-dsrv9703c.dtb \
-	sun4i-a10-gemei-g9.dtb \
-	sun4i-a10-hackberry.dtb \
-	sun4i-a10-hyundai-a7hd.dtb \
-	sun4i-a10-inet1.dtb \
-	sun4i-a10-inet97fv2.dtb \
-	sun4i-a10-inet9f-rev03.dtb \
-	sun4i-a10-itead-iteaduino-plus.dtb \
-	sun4i-a10-jesurun-q5.dtb \
-	sun4i-a10-marsboard.dtb \
-	sun4i-a10-mini-xplus.dtb \
-	sun4i-a10-mk802.dtb \
-	sun4i-a10-mk802ii.dtb \
-	sun4i-a10-olinuxino-lime.dtb \
-	sun4i-a10-pcduino.dtb \
-	sun4i-a10-pcduino2.dtb \
-	sun4i-a10-pov-protab2-ips9.dtb \
-	sun4i-a10-topwise-a721.dtb
-dtb-$(CONFIG_MACH_SUN5I) += \
-	sun5i-a10s-auxtek-t003.dtb \
-	sun5i-a10s-auxtek-t004.dtb \
-	sun5i-a10s-mk802.dtb \
-	sun5i-a10s-olinuxino-micro.dtb \
-	sun5i-a10s-r7-tv-dongle.dtb \
-	sun5i-a10s-wobo-i5.dtb \
-	sun5i-a13-difrnce-dit4350.dtb \
-	sun5i-a13-empire-electronix-d709.dtb \
-	sun5i-a13-empire-electronix-m712.dtb \
-	sun5i-a13-hsg-h702.dtb \
-	sun5i-a13-inet-98v-rev2.dtb \
-	sun5i-a13-licheepi-one.dtb \
-	sun5i-a13-olinuxino.dtb \
-	sun5i-a13-olinuxino-micro.dtb \
-	sun5i-a13-pocketbook-touch-lux-3.dtb \
-	sun5i-a13-q8-tablet.dtb \
-	sun5i-a13-utoo-p66.dtb \
-	sun5i-gr8-chip-pro.dtb \
-	sun5i-gr8-evb.dtb \
-	sun5i-r8-chip.dtb
-dtb-$(CONFIG_MACH_SUN6I) += \
-	sun6i-a31-app4-evb1.dtb \
-	sun6i-a31-colombus.dtb \
-	sun6i-a31-hummingbird.dtb \
-	sun6i-a31-i7.dtb \
-	sun6i-a31-m9.dtb \
-	sun6i-a31-mele-a1000g-quad.dtb \
-	sun6i-a31s-colorfly-e708-q1.dtb \
-	sun6i-a31s-cs908.dtb \
-	sun6i-a31s-inet-q972.dtb \
-	sun6i-a31s-primo81.dtb \
-	sun6i-a31s-sina31s.dtb \
-	sun6i-a31s-sinovoip-bpi-m2.dtb \
-	sun6i-a31s-yones-toptech-bs1078-v2.dtb
-dtb-$(CONFIG_MACH_SUN7I) += \
-	sun7i-a20-bananapi.dtb \
-	sun7i-a20-bananapi-m1-plus.dtb \
-	sun7i-a20-bananapro.dtb \
-	sun7i-a20-cubieboard2.dtb \
-	sun7i-a20-cubietruck.dtb \
-	sun7i-a20-haoyu-marsboard.dtb \
-	sun7i-a20-hummingbird.dtb \
-	sun7i-a20-itead-ibox.dtb \
-	sun7i-a20-i12-tvbox.dtb \
-	sun7i-a20-icnova-swac.dtb \
-	sun7i-a20-lamobo-r1.dtb \
-	sun7i-a20-linutronix-testbox-v2.dtb \
-	sun7i-a20-m3.dtb \
-	sun7i-a20-mk808c.dtb \
-	sun7i-a20-olimex-som-evb.dtb \
-	sun7i-a20-olimex-som-evb-emmc.dtb \
-	sun7i-a20-olimex-som204-evb.dtb \
-	sun7i-a20-olimex-som204-evb-emmc.dtb \
-	sun7i-a20-olinuxino-lime.dtb \
-	sun7i-a20-olinuxino-lime-emmc.dtb \
-	sun7i-a20-olinuxino-lime2.dtb \
-	sun7i-a20-olinuxino-lime2-emmc.dtb \
-	sun7i-a20-olinuxino-micro.dtb \
-	sun7i-a20-olinuxino-micro-emmc.dtb \
-	sun7i-a20-orangepi.dtb \
-	sun7i-a20-orangepi-mini.dtb \
-	sun7i-a20-pcduino3.dtb \
-	sun7i-a20-pcduino3-nano.dtb \
-	sun7i-a20-wexler-tab7200.dtb \
-	sun7i-a20-wits-pro-a20-dkt.dtb
-dtb-$(CONFIG_MACH_SUN8I) += \
-	sun8i-a23-evb.dtb \
-	sun8i-a23-gt90h-v4.dtb \
-	sun8i-a23-inet86dz.dtb \
-	sun8i-a23-ippo-q8h-v5.dtb \
-	sun8i-a23-ippo-q8h-v1.2.dtb \
-	sun8i-a23-polaroid-mid2407pxe03.dtb \
-	sun8i-a23-polaroid-mid2809pxe04.dtb \
-	sun8i-a23-q8-tablet.dtb \
-	sun8i-a33-et-q8-v1.6.dtb \
-	sun8i-a33-ga10h-v1.1.dtb \
-	sun8i-a33-inet-d978-rev2.dtb \
-	sun8i-a33-ippo-q8h-v1.2.dtb \
-	sun8i-a33-olinuxino.dtb \
-	sun8i-a33-q8-tablet.dtb \
-	sun8i-a33-sinlinx-sina33.dtb \
-	sun8i-a83t-allwinner-h8homlet-v2.dtb \
-	sun8i-a83t-bananapi-m3.dtb \
-	sun8i-a83t-cubietruck-plus.dtb \
-	sun8i-a83t-tbs-a711.dtb \
-	sun8i-h2-plus-bananapi-m2-zero.dtb \
-	sun8i-h2-plus-libretech-all-h3-cc.dtb \
-	sun8i-h2-plus-orangepi-r1.dtb \
-	sun8i-h2-plus-orangepi-zero.dtb \
-	sun8i-h3-bananapi-m2-plus.dtb \
-	sun8i-h3-bananapi-m2-plus-v1.2.dtb \
-	sun8i-h3-beelink-x2.dtb \
-	sun8i-h3-libretech-all-h3-cc.dtb \
-	sun8i-h3-mapleboard-mp130.dtb \
-	sun8i-h3-nanopi-duo2.dtb \
-	sun8i-h3-nanopi-m1.dtb	\
-	sun8i-h3-nanopi-m1-plus.dtb \
-	sun8i-h3-nanopi-neo.dtb \
-	sun8i-h3-nanopi-neo-air.dtb \
-	sun8i-h3-nanopi-r1.dtb \
-	sun8i-h3-orangepi-2.dtb \
-	sun8i-h3-orangepi-lite.dtb \
-	sun8i-h3-orangepi-one.dtb \
-	sun8i-h3-orangepi-pc.dtb \
-	sun8i-h3-orangepi-pc-plus.dtb \
-	sun8i-h3-orangepi-plus.dtb \
-	sun8i-h3-orangepi-plus2e.dtb \
-	sun8i-h3-orangepi-zero-plus2.dtb \
-	sun8i-h3-rervision-dvk.dtb \
-	sun8i-h3-zeropi.dtb \
-	sun8i-h3-emlid-neutis-n5h3-devboard.dtb \
-	sun8i-r16-bananapi-m2m.dtb \
-	sun8i-r16-nintendo-nes-classic.dtb \
-	sun8i-r16-nintendo-super-nes-classic.dtb \
-	sun8i-r16-parrot.dtb \
-	sun8i-r40-bananapi-m2-ultra.dtb \
-	sun8i-r40-oka40i-c.dtb \
-	sun8i-s3-elimo-initium.dtb \
-	sun8i-s3-lichee-zero-plus.dtb \
-	sun8i-s3-pinecube.dtb \
-	sun8i-t3-cqa3t-bv3.dtb \
-	sun8i-v3-sl631-imx179.dtb \
-	sun8i-v3s-licheepi-zero.dtb \
-	sun8i-v3s-licheepi-zero-dock.dtb \
-	sun8i-v40-bananapi-m2-berry.dtb
-dtb-$(CONFIG_MACH_SUN9I) += \
-	sun9i-a80-optimus.dtb \
-	sun9i-a80-cubieboard4.dtb
-dtb-$(CONFIG_MACH_SUNIV) += \
-	suniv-f1c100s-licheepi-nano.dtb
-dtb-$(CONFIG_ARCH_TEGRA_2x_SOC) += \
-	tegra20-acer-a500-picasso.dtb \
-	tegra20-asus-tf101.dtb \
-	tegra20-harmony.dtb \
-	tegra20-colibri-eval-v3.dtb \
-	tegra20-colibri-iris.dtb \
-	tegra20-medcom-wide.dtb \
-	tegra20-paz00.dtb \
-	tegra20-plutux.dtb \
-	tegra20-seaboard.dtb \
-	tegra20-tec.dtb \
-	tegra20-trimslice.dtb \
-	tegra20-ventana.dtb
-dtb-$(CONFIG_ARCH_TEGRA_3x_SOC) += \
-	tegra30-apalis-eval.dtb \
-	tegra30-apalis-v1.1-eval.dtb \
-	tegra30-asus-nexus7-grouper-PM269.dtb \
-	tegra30-asus-nexus7-grouper-E1565.dtb \
-	tegra30-asus-nexus7-tilapia-E1565.dtb \
-	tegra30-asus-tf201.dtb \
-	tegra30-asus-tf300t.dtb \
-	tegra30-asus-tf300tg.dtb \
-	tegra30-asus-tf700t.dtb \
-	tegra30-beaver.dtb \
-	tegra30-cardhu-a02.dtb \
-	tegra30-cardhu-a04.dtb \
-	tegra30-colibri-eval-v3.dtb \
-	tegra30-ouya.dtb \
-	tegra30-pegatron-chagall.dtb
-dtb-$(CONFIG_ARCH_TEGRA_114_SOC) += \
-	tegra114-asus-tf701t.dtb \
-	tegra114-dalmore.dtb \
-	tegra114-roth.dtb \
-	tegra114-tn7.dtb
-dtb-$(CONFIG_ARCH_TEGRA_124_SOC) += \
-	tegra124-apalis-eval.dtb \
-	tegra124-apalis-v1.2-eval.dtb \
-	tegra124-jetson-tk1.dtb \
-	tegra124-nyan-big.dtb \
-	tegra124-nyan-big-fhd.dtb \
-	tegra124-nyan-blaze.dtb \
-	tegra124-venice2.dtb
-dtb-$(CONFIG_ARCH_U8500) += \
-	ste-snowball.dtb \
-	ste-hrefprev60-stuib.dtb \
-	ste-hrefprev60-tvk.dtb \
-	ste-hrefv60plus-stuib.dtb \
-	ste-hrefv60plus-tvk.dtb \
-	ste-href520-tvk.dtb \
-	ste-ux500-samsung-golden.dtb \
-	ste-ux500-samsung-janice.dtb \
-	ste-ux500-samsung-gavini.dtb \
-	ste-ux500-samsung-codina.dtb \
-	ste-ux500-samsung-skomer.dtb \
-	ste-ux500-samsung-kyle.dtb
-dtb-$(CONFIG_ARCH_UNIPHIER) += \
-	uniphier-ld4-ref.dtb \
-	uniphier-ld6b-ref.dtb \
-	uniphier-pro4-ace.dtb \
-	uniphier-pro4-ref.dtb \
-	uniphier-pro4-sanji.dtb \
-	uniphier-pxs2-gentil.dtb \
-	uniphier-pxs2-vodka.dtb \
-	uniphier-sld8-ref.dtb
-dtb-$(CONFIG_ARCH_VERSATILE) += \
-	versatile-ab.dtb \
-	versatile-ab-ib2.dtb \
-	versatile-pb.dtb
-dtb-$(CONFIG_ARCH_VEXPRESS) += \
-	vexpress-v2p-ca5s.dtb \
-	vexpress-v2p-ca9.dtb \
-	vexpress-v2p-ca15-tc1.dtb \
-	vexpress-v2p-ca15_a7.dtb
-dtb-$(CONFIG_ARCH_VIRT) += \
-	xenvm-4.2.dtb
-dtb-$(CONFIG_ARCH_VT8500) += \
-	vt8500-bv07.dtb \
-	wm8505-ref.dtb \
-	wm8650-mid.dtb \
-	wm8750-apc8750.dtb \
-	wm8850-w70v2.dtb
-dtb-$(CONFIG_ARCH_ZYNQ) += \
-	zynq-cc108.dtb \
-	zynq-ebaz4205.dtb \
-	zynq-microzed.dtb \
-	zynq-parallella.dtb \
-	zynq-zc702.dtb \
-	zynq-zc706.dtb \
-	zynq-zc770-xm010.dtb \
-	zynq-zc770-xm011.dtb \
-	zynq-zc770-xm012.dtb \
-	zynq-zc770-xm013.dtb \
-	zynq-zed.dtb \
-	zynq-zturn.dtb \
-	zynq-zturn-v5.dtb \
-	zynq-zybo.dtb \
-	zynq-zybo-z7.dtb
-dtb-$(CONFIG_MACH_ARMADA_370) += \
-	armada-370-c200-v2.dtb \
-	armada-370-db.dtb \
-	armada-370-dlink-dns327l.dtb \
-	armada-370-mirabox.dtb \
-	armada-370-netgear-rn102.dtb \
-	armada-370-netgear-rn104.dtb \
-	armada-370-rd.dtb \
-	armada-370-seagate-nas-2bay.dtb \
-	armada-370-seagate-nas-4bay.dtb \
-	armada-370-seagate-personal-cloud.dtb \
-	armada-370-seagate-personal-cloud-2bay.dtb \
-	armada-370-synology-ds213j.dtb
-dtb-$(CONFIG_MACH_ARMADA_375) += \
-	armada-375-db.dtb
-dtb-$(CONFIG_MACH_ARMADA_38X) += \
-	armada-381-netgear-gs110emx.dtb \
-	armada-382-rd-ac3x-48g4x2xl.dtb \
-	armada-385-atl-x530.dtb\
-	armada-385-clearfog-gtr-s4.dtb \
-	armada-385-clearfog-gtr-l8.dtb \
-	armada-385-db-88f6820-amc.dtb \
-	armada-385-db-ap.dtb \
-	armada-385-linksys-caiman.dtb \
-	armada-385-linksys-cobra.dtb \
-	armada-385-linksys-rango.dtb \
-	armada-385-linksys-shelby.dtb \
-	armada-385-synology-ds116.dtb \
-	armada-385-turris-omnia.dtb \
-	armada-388-clearfog.dtb \
-	armada-388-clearfog-base.dtb \
-	armada-388-clearfog-pro.dtb \
-	armada-388-db.dtb \
-	armada-388-gp.dtb \
-	armada-388-helios4.dtb \
-	armada-388-rd.dtb
-dtb-$(CONFIG_MACH_ARMADA_39X) += \
-	armada-398-db.dtb
-dtb-$(CONFIG_MACH_ARMADA_XP) += \
-	armada-xp-axpwifiap.dtb \
-	armada-xp-crs305-1g-4s.dtb \
-	armada-xp-crs305-1g-4s-bit.dtb \
-	armada-xp-crs326-24g-2s.dtb \
-	armada-xp-crs326-24g-2s-bit.dtb \
-	armada-xp-crs328-4c-20s-4s.dtb \
-	armada-xp-crs328-4c-20s-4s-bit.dtb \
-	armada-xp-db.dtb \
-	armada-xp-db-dxbc2.dtb \
-	armada-xp-db-xc3-24g4xg.dtb \
-	armada-xp-gp.dtb \
-	armada-xp-lenovo-ix4-300d.dtb \
-	armada-xp-linksys-mamba.dtb \
-	armada-xp-matrix.dtb \
-	armada-xp-netgear-rn2120.dtb \
-	armada-xp-openblocks-ax3-4.dtb \
-	armada-xp-synology-ds414.dtb
-dtb-$(CONFIG_MACH_DOVE) += \
-	dove-cubox.dtb \
-	dove-cubox-es.dtb \
-	dove-d2plug.dtb \
-	dove-d3plug.dtb \
-	dove-dove-db.dtb \
-	dove-sbc-a510.dtb
-dtb-$(CONFIG_ARCH_MEDIATEK) += \
-	mt2701-evb.dtb \
-	mt6580-evbp1.dtb \
-	mt6589-aquaris5.dtb \
-	mt6589-fairphone-fp1.dtb \
-	mt6592-evb.dtb \
-	mt7623a-rfb-emmc.dtb \
-	mt7623a-rfb-nand.dtb \
-	mt7623n-rfb-emmc.dtb \
-	mt7623n-bananapi-bpi-r2.dtb \
-	mt7629-rfb.dtb \
-	mt8127-moose.dtb \
-	mt8135-evbp1.dtb
-dtb-$(CONFIG_ARCH_MILBEAUT) += milbeaut-m10v-evb.dtb
-dtb-$(CONFIG_ARCH_MSTARV7) += \
-	mstar-infinity-msc313-breadbee_crust.dtb \
-	mstar-infinity2m-ssd202d-100ask-dongshanpione.dtb \
-	mstar-infinity2m-ssd202d-miyoo-mini.dtb \
-	mstar-infinity2m-ssd202d-wirelesstag-ido-sbc2d06-v1b-22w.dtb \
-	mstar-infinity2m-ssd202d-ssd201htv2.dtb \
-	mstar-infinity2m-ssd202d-unitv2.dtb \
-	mstar-infinity3-msc313e-breadbee.dtb \
-	mstar-mercury5-ssc8336n-midrived08.dtb
-dtb-$(CONFIG_ARCH_ASPEED) += \
-	aspeed-ast2500-evb.dtb \
-	aspeed-ast2600-evb-a1.dtb \
-	aspeed-ast2600-evb.dtb \
-	aspeed-bmc-amd-ethanolx.dtb \
-	aspeed-bmc-ampere-mtjade.dtb \
-	aspeed-bmc-arm-centriq2400-rep.dtb \
-	aspeed-bmc-arm-stardragon4800-rep2.dtb \
-	aspeed-bmc-asrock-e3c246d4i.dtb \
-	aspeed-bmc-asrock-romed8hm3.dtb \
-	aspeed-bmc-bytedance-g220a.dtb \
-	aspeed-bmc-facebook-bletchley.dtb \
-	aspeed-bmc-facebook-cloudripper.dtb \
-	aspeed-bmc-facebook-cmm.dtb \
-	aspeed-bmc-facebook-elbert.dtb \
-	aspeed-bmc-facebook-fuji.dtb \
-	aspeed-bmc-facebook-galaxy100.dtb \
-	aspeed-bmc-facebook-minipack.dtb \
-	aspeed-bmc-facebook-tiogapass.dtb \
-	aspeed-bmc-facebook-wedge40.dtb \
-	aspeed-bmc-facebook-wedge100.dtb \
-	aspeed-bmc-facebook-wedge400.dtb \
-	aspeed-bmc-facebook-yamp.dtb \
-	aspeed-bmc-facebook-yosemitev2.dtb \
-	aspeed-bmc-ibm-everest.dtb \
-	aspeed-bmc-ibm-rainier.dtb \
-	aspeed-bmc-ibm-rainier-1s4u.dtb \
-	aspeed-bmc-ibm-rainier-4u.dtb \
-	aspeed-bmc-intel-s2600wf.dtb \
-	aspeed-bmc-inspur-fp5280g2.dtb \
-	aspeed-bmc-inspur-nf5280m6.dtb \
-	aspeed-bmc-lenovo-hr630.dtb \
-	aspeed-bmc-lenovo-hr855xg2.dtb \
-	aspeed-bmc-microsoft-olympus.dtb \
-	aspeed-bmc-opp-lanyang.dtb \
-	aspeed-bmc-opp-mihawk.dtb \
-	aspeed-bmc-opp-mowgli.dtb \
-	aspeed-bmc-opp-nicole.dtb \
-	aspeed-bmc-opp-palmetto.dtb \
-	aspeed-bmc-opp-romulus.dtb \
-	aspeed-bmc-opp-swift.dtb \
-	aspeed-bmc-opp-tacoma.dtb \
-	aspeed-bmc-opp-vesnin.dtb \
-	aspeed-bmc-opp-witherspoon.dtb \
-	aspeed-bmc-opp-zaius.dtb \
-	aspeed-bmc-portwell-neptune.dtb \
-	aspeed-bmc-quanta-q71l.dtb \
-	aspeed-bmc-quanta-s6q.dtb \
-	aspeed-bmc-supermicro-x11spi.dtb \
-	aspeed-bmc-inventec-transformers.dtb \
-	aspeed-bmc-tyan-s7106.dtb \
-	aspeed-bmc-tyan-s8036.dtb \
-	aspeed-bmc-vegman-n110.dtb \
-	aspeed-bmc-vegman-rx20.dtb \
-	aspeed-bmc-vegman-sx20.dtb
+subdir-y += actions
+subdir-y += airoha
+subdir-y += allwinner
+subdir-y += alphascale
+subdir-y += amazon
+subdir-y += amlogic
+subdir-y += arm
+subdir-y += aspeed
+subdir-y += axis
+subdir-y += broadcom
+subdir-y += calxeda
+subdir-y += cirrus
+subdir-y += cnxt
+subdir-y += gemini
+subdir-y += hisilicon
+subdir-y += hpe
+subdir-y += intel
+subdir-y += marvell
+subdir-y += mediatek
+subdir-y += microchip
+subdir-y += moxa
+subdir-y += nspire
+subdir-y += nuvoton
+subdir-y += nvidia
+subdir-y += nxp
+subdir-y += qcom
+subdir-y += realtek
+subdir-y += renesas
+subdir-y += rockchip
+subdir-y += samsung
+subdir-y += sigmastar
+subdir-y += socionext
+subdir-y += st
+subdir-y += sunplus
+subdir-y += synaptics
+subdir-y += ti
+subdir-y += unisoc
+subdir-y += vt8500
+subdir-y += xen
+subdir-y += xilinx
diff --git a/arch/arm/boot/dts/actions/Makefile b/arch/arm/boot/dts/actions/Makefile
new file mode 100644
index 000000000000..f384e4a48e6f
--- /dev/null
+++ b/arch/arm/boot/dts/actions/Makefile
@@ -0,0 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_ACTIONS) += \
+	owl-s500-cubieboard6.dtb \
+	owl-s500-guitar-bb-rev-b.dtb \
+	owl-s500-labrador-base-m.dtb \
+	owl-s500-roseapplepi.dtb \
+	owl-s500-sparky.dtb
diff --git a/arch/arm/boot/dts/owl-s500-cubieboard6.dts b/arch/arm/boot/dts/actions/owl-s500-cubieboard6.dts
index c2b02895910c..c2b02895910c 100644
--- a/arch/arm/boot/dts/owl-s500-cubieboard6.dts
+++ b/arch/arm/boot/dts/actions/owl-s500-cubieboard6.dts
diff --git a/arch/arm/boot/dts/owl-s500-guitar-bb-rev-b.dts b/arch/arm/boot/dts/actions/owl-s500-guitar-bb-rev-b.dts
index 7ae34a23e320..7ae34a23e320 100644
--- a/arch/arm/boot/dts/owl-s500-guitar-bb-rev-b.dts
+++ b/arch/arm/boot/dts/actions/owl-s500-guitar-bb-rev-b.dts
diff --git a/arch/arm/boot/dts/owl-s500-guitar.dtsi b/arch/arm/boot/dts/actions/owl-s500-guitar.dtsi
index 81cc39871f17..81cc39871f17 100644
--- a/arch/arm/boot/dts/owl-s500-guitar.dtsi
+++ b/arch/arm/boot/dts/actions/owl-s500-guitar.dtsi
diff --git a/arch/arm/boot/dts/owl-s500-labrador-base-m.dts b/arch/arm/boot/dts/actions/owl-s500-labrador-base-m.dts
index 1585e33f703b..1585e33f703b 100644
--- a/arch/arm/boot/dts/owl-s500-labrador-base-m.dts
+++ b/arch/arm/boot/dts/actions/owl-s500-labrador-base-m.dts
diff --git a/arch/arm/boot/dts/owl-s500-labrador-v2.dtsi b/arch/arm/boot/dts/actions/owl-s500-labrador-v2.dtsi
index 883ff2f9886d..883ff2f9886d 100644
--- a/arch/arm/boot/dts/owl-s500-labrador-v2.dtsi
+++ b/arch/arm/boot/dts/actions/owl-s500-labrador-v2.dtsi
diff --git a/arch/arm/boot/dts/owl-s500-roseapplepi.dts b/arch/arm/boot/dts/actions/owl-s500-roseapplepi.dts
index eb555f385283..eb555f385283 100644
--- a/arch/arm/boot/dts/owl-s500-roseapplepi.dts
+++ b/arch/arm/boot/dts/actions/owl-s500-roseapplepi.dts
diff --git a/arch/arm/boot/dts/owl-s500-sparky.dts b/arch/arm/boot/dts/actions/owl-s500-sparky.dts
index 9d8f7336bec0..9d8f7336bec0 100644
--- a/arch/arm/boot/dts/owl-s500-sparky.dts
+++ b/arch/arm/boot/dts/actions/owl-s500-sparky.dts
diff --git a/arch/arm/boot/dts/owl-s500.dtsi b/arch/arm/boot/dts/actions/owl-s500.dtsi
index 739b4b9cec8c..739b4b9cec8c 100644
--- a/arch/arm/boot/dts/owl-s500.dtsi
+++ b/arch/arm/boot/dts/actions/owl-s500.dtsi
diff --git a/arch/arm/boot/dts/airoha/Makefile b/arch/arm/boot/dts/airoha/Makefile
new file mode 100644
index 000000000000..00c31389f622
--- /dev/null
+++ b/arch/arm/boot/dts/airoha/Makefile
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_AIROHA) += \
+	en7523-evb.dtb
diff --git a/arch/arm/boot/dts/en7523-evb.dts b/arch/arm/boot/dts/airoha/en7523-evb.dts
index a8d8bb0419a0..f23a25cce119 100644
--- a/arch/arm/boot/dts/en7523-evb.dts
+++ b/arch/arm/boot/dts/airoha/en7523-evb.dts
@@ -33,3 +33,11 @@
 &gpio1 {
 	status = "okay";
 };
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/en7523.dtsi b/arch/arm/boot/dts/airoha/en7523.dtsi
index 36597f587f46..b523a868c4ad 100644
--- a/arch/arm/boot/dts/en7523.dtsi
+++ b/arch/arm/boot/dts/airoha/en7523.dtsi
@@ -3,6 +3,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/en7523-clk.h>
 
 / {
 	interrupt-parent = <&gic>;
@@ -80,9 +81,18 @@
 
 		L2_0: l2-cache0 {
 			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
 		};
 	};
 
+	scu: system-controller@1fa20000 {
+		compatible = "airoha,en7523-scu";
+		reg = <0x1fa20000 0x400>,
+		      <0x1fb00000 0x1000>;
+		#clock-cells = <1>;
+	};
+
 	gic: interrupt-controller@9000000 {
 		compatible = "arm,gic-v3";
 		interrupt-controller;
@@ -135,4 +145,62 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
+
+	pcie0: pcie@1fa91000 {
+		compatible = "airoha,en7523-pcie", "mediatek,mt7622-pcie";
+		device_type = "pci";
+		reg = <0x1fa91000 0x1000>;
+		reg-names = "port0";
+		linux,pci-domain = <0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "pcie_irq";
+		clocks = <&scu EN7523_CLK_PCIE>;
+		clock-names = "sys_ck0";
+		bus-range = <0x00 0xff>;
+		ranges = <0x82000000 0 0x20000000  0x20000000  0 0x8000000>;
+		status = "disabled";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie_intc0 0>,
+				<0 0 0 2 &pcie_intc0 1>,
+				<0 0 0 3 &pcie_intc0 2>,
+				<0 0 0 4 &pcie_intc0 3>;
+		pcie_intc0: interrupt-controller {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+		};
+	};
+
+	pcie1: pcie@1fa92000 {
+		compatible = "airoha,en7523-pcie", "mediatek,mt7622-pcie";
+		device_type = "pci";
+		reg = <0x1fa92000 0x1000>;
+		reg-names = "port1";
+		linux,pci-domain = <1>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "pcie_irq";
+		clocks = <&scu EN7523_CLK_PCIE>;
+		clock-names = "sys_ck1";
+		bus-range = <0x00 0xff>;
+		ranges = <0x82000000 0 0x28000000  0x28000000  0 0x8000000>;
+		status = "disabled";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie_intc1 0>,
+				<0 0 0 2 &pcie_intc1 1>,
+				<0 0 0 3 &pcie_intc1 2>,
+				<0 0 0 4 &pcie_intc1 3>;
+		pcie_intc1: interrupt-controller {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+		};
+	};
 };
diff --git a/arch/arm/boot/dts/allwinner/Makefile b/arch/arm/boot/dts/allwinner/Makefile
new file mode 100644
index 000000000000..f71392a55df8
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/Makefile
@@ -0,0 +1,283 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_MACH_SUN4I) += \
+	sun4i-a10-a1000.dtb \
+	sun4i-a10-ba10-tvbox.dtb \
+	sun4i-a10-chuwi-v7-cw0825.dtb \
+	sun4i-a10-cubieboard.dtb \
+	sun4i-a10-dserve-dsrv9703c.dtb \
+	sun4i-a10-gemei-g9.dtb \
+	sun4i-a10-hackberry.dtb \
+	sun4i-a10-hyundai-a7hd.dtb \
+	sun4i-a10-inet1.dtb \
+	sun4i-a10-inet97fv2.dtb \
+	sun4i-a10-inet9f-rev03.dtb \
+	sun4i-a10-itead-iteaduino-plus.dtb \
+	sun4i-a10-jesurun-q5.dtb \
+	sun4i-a10-marsboard.dtb \
+	sun4i-a10-mini-xplus.dtb \
+	sun4i-a10-mk802.dtb \
+	sun4i-a10-mk802ii.dtb \
+	sun4i-a10-olinuxino-lime.dtb \
+	sun4i-a10-pcduino.dtb \
+	sun4i-a10-pcduino2.dtb \
+	sun4i-a10-pov-protab2-ips9.dtb \
+	sun4i-a10-topwise-a721.dtb
+dtb-$(CONFIG_MACH_SUN4I) += \
+	sun4i-a10-a1000.dtb \
+	sun4i-a10-ba10-tvbox.dtb \
+	sun4i-a10-chuwi-v7-cw0825.dtb \
+	sun4i-a10-cubieboard.dtb \
+	sun4i-a10-dserve-dsrv9703c.dtb \
+	sun4i-a10-gemei-g9.dtb \
+	sun4i-a10-hackberry.dtb \
+	sun4i-a10-hyundai-a7hd.dtb \
+	sun4i-a10-inet1.dtb \
+	sun4i-a10-inet97fv2.dtb \
+	sun4i-a10-inet9f-rev03.dtb \
+	sun4i-a10-itead-iteaduino-plus.dtb \
+	sun4i-a10-jesurun-q5.dtb \
+	sun4i-a10-marsboard.dtb \
+	sun4i-a10-mini-xplus.dtb \
+	sun4i-a10-mk802.dtb \
+	sun4i-a10-mk802ii.dtb \
+	sun4i-a10-olinuxino-lime.dtb \
+	sun4i-a10-pcduino.dtb \
+	sun4i-a10-pcduino2.dtb \
+	sun4i-a10-pov-protab2-ips9.dtb \
+	sun4i-a10-topwise-a721.dtb
+dtb-$(CONFIG_MACH_SUN5I) += \
+	sun5i-a10s-auxtek-t003.dtb \
+	sun5i-a10s-auxtek-t004.dtb \
+	sun5i-a10s-mk802.dtb \
+	sun5i-a10s-olinuxino-micro.dtb \
+	sun5i-a10s-r7-tv-dongle.dtb \
+	sun5i-a10s-wobo-i5.dtb \
+	sun5i-a13-difrnce-dit4350.dtb \
+	sun5i-a13-empire-electronix-d709.dtb \
+	sun5i-a13-empire-electronix-m712.dtb \
+	sun5i-a13-hsg-h702.dtb \
+	sun5i-a13-inet-98v-rev2.dtb \
+	sun5i-a13-licheepi-one.dtb \
+	sun5i-a13-olinuxino.dtb \
+	sun5i-a13-olinuxino-micro.dtb \
+	sun5i-a13-pocketbook-touch-lux-3.dtb \
+	sun5i-a13-pocketbook-614-plus.dtb \
+	sun5i-a13-q8-tablet.dtb \
+	sun5i-a13-utoo-p66.dtb \
+	sun5i-gr8-chip-pro.dtb \
+	sun5i-gr8-evb.dtb \
+	sun5i-r8-chip.dtb
+dtb-$(CONFIG_MACH_SUN5I) += \
+	sun5i-a10s-auxtek-t003.dtb \
+	sun5i-a10s-auxtek-t004.dtb \
+	sun5i-a10s-mk802.dtb \
+	sun5i-a10s-olinuxino-micro.dtb \
+	sun5i-a10s-r7-tv-dongle.dtb \
+	sun5i-a10s-wobo-i5.dtb \
+	sun5i-a13-difrnce-dit4350.dtb \
+	sun5i-a13-empire-electronix-d709.dtb \
+	sun5i-a13-empire-electronix-m712.dtb \
+	sun5i-a13-hsg-h702.dtb \
+	sun5i-a13-inet-98v-rev2.dtb \
+	sun5i-a13-licheepi-one.dtb \
+	sun5i-a13-olinuxino.dtb \
+	sun5i-a13-olinuxino-micro.dtb \
+	sun5i-a13-pocketbook-touch-lux-3.dtb \
+	sun5i-a13-q8-tablet.dtb \
+	sun5i-a13-utoo-p66.dtb \
+	sun5i-gr8-chip-pro.dtb \
+	sun5i-gr8-evb.dtb \
+	sun5i-r8-chip.dtb
+dtb-$(CONFIG_MACH_SUN6I) += \
+	sun6i-a31-app4-evb1.dtb \
+	sun6i-a31-colombus.dtb \
+	sun6i-a31-hummingbird.dtb \
+	sun6i-a31-i7.dtb \
+	sun6i-a31-m9.dtb \
+	sun6i-a31-mele-a1000g-quad.dtb \
+	sun6i-a31s-colorfly-e708-q1.dtb \
+	sun6i-a31s-cs908.dtb \
+	sun6i-a31s-inet-q972.dtb \
+	sun6i-a31s-primo81.dtb \
+	sun6i-a31s-sina31s.dtb \
+	sun6i-a31s-sinovoip-bpi-m2.dtb \
+	sun6i-a31s-yones-toptech-bs1078-v2.dtb
+dtb-$(CONFIG_MACH_SUN6I) += \
+	sun6i-a31-app4-evb1.dtb \
+	sun6i-a31-colombus.dtb \
+	sun6i-a31-hummingbird.dtb \
+	sun6i-a31-i7.dtb \
+	sun6i-a31-m9.dtb \
+	sun6i-a31-mele-a1000g-quad.dtb \
+	sun6i-a31s-colorfly-e708-q1.dtb \
+	sun6i-a31s-cs908.dtb \
+	sun6i-a31s-inet-q972.dtb \
+	sun6i-a31s-primo81.dtb \
+	sun6i-a31s-sina31s.dtb \
+	sun6i-a31s-sinovoip-bpi-m2.dtb \
+	sun6i-a31s-yones-toptech-bs1078-v2.dtb
+dtb-$(CONFIG_MACH_SUN7I) += \
+	sun7i-a20-bananapi.dtb \
+	sun7i-a20-bananapi-m1-plus.dtb \
+	sun7i-a20-bananapro.dtb \
+	sun7i-a20-cubieboard2.dtb \
+	sun7i-a20-cubietruck.dtb \
+	sun7i-a20-haoyu-marsboard.dtb \
+	sun7i-a20-hummingbird.dtb \
+	sun7i-a20-itead-ibox.dtb \
+	sun7i-a20-i12-tvbox.dtb \
+	sun7i-a20-icnova-a20-adb4006.dtb \
+	sun7i-a20-icnova-swac.dtb \
+	sun7i-a20-lamobo-r1.dtb \
+	sun7i-a20-linutronix-testbox-v2.dtb \
+	sun7i-a20-m3.dtb \
+	sun7i-a20-mk808c.dtb \
+	sun7i-a20-olimex-som-evb.dtb \
+	sun7i-a20-olimex-som-evb-emmc.dtb \
+	sun7i-a20-olimex-som204-evb.dtb \
+	sun7i-a20-olimex-som204-evb-emmc.dtb \
+	sun7i-a20-olinuxino-lime.dtb \
+	sun7i-a20-olinuxino-lime-emmc.dtb \
+	sun7i-a20-olinuxino-lime2.dtb \
+	sun7i-a20-olinuxino-lime2-emmc.dtb \
+	sun7i-a20-olinuxino-micro.dtb \
+	sun7i-a20-olinuxino-micro-emmc.dtb \
+	sun7i-a20-orangepi.dtb \
+	sun7i-a20-orangepi-mini.dtb \
+	sun7i-a20-pcduino3.dtb \
+	sun7i-a20-pcduino3-nano.dtb \
+	sun7i-a20-wexler-tab7200.dtb \
+	sun7i-a20-wits-pro-a20-dkt.dtb
+dtb-$(CONFIG_MACH_SUN7I) += \
+	sun7i-a20-bananapi.dtb \
+	sun7i-a20-bananapi-m1-plus.dtb \
+	sun7i-a20-bananapro.dtb \
+	sun7i-a20-cubieboard2.dtb \
+	sun7i-a20-cubietruck.dtb \
+	sun7i-a20-haoyu-marsboard.dtb \
+	sun7i-a20-hummingbird.dtb \
+	sun7i-a20-itead-ibox.dtb \
+	sun7i-a20-i12-tvbox.dtb \
+	sun7i-a20-icnova-a20-adb4006.dtb \
+	sun7i-a20-icnova-swac.dtb \
+	sun7i-a20-lamobo-r1.dtb \
+	sun7i-a20-linutronix-testbox-v2.dtb \
+	sun7i-a20-m3.dtb \
+	sun7i-a20-mk808c.dtb \
+	sun7i-a20-olimex-som-evb.dtb \
+	sun7i-a20-olimex-som-evb-emmc.dtb \
+	sun7i-a20-olimex-som204-evb.dtb \
+	sun7i-a20-olimex-som204-evb-emmc.dtb \
+	sun7i-a20-olinuxino-lime.dtb \
+	sun7i-a20-olinuxino-lime-emmc.dtb \
+	sun7i-a20-olinuxino-lime2.dtb \
+	sun7i-a20-olinuxino-lime2-emmc.dtb \
+	sun7i-a20-olinuxino-micro.dtb \
+	sun7i-a20-olinuxino-micro-emmc.dtb \
+	sun7i-a20-orangepi.dtb \
+	sun7i-a20-orangepi-mini.dtb \
+	sun7i-a20-pcduino3.dtb \
+	sun7i-a20-pcduino3-nano.dtb \
+	sun7i-a20-wexler-tab7200.dtb \
+	sun7i-a20-wits-pro-a20-dkt.dtb
+
+# Enables support for device-tree overlays for all pis
+DTC_FLAGS_sun8i-h2-plus-orangepi-zero := -@
+DTC_FLAGS_sun8i-h3-orangepi-lite := -@
+DTC_FLAGS_sun8i-h3-bananapi-m2-plus := -@
+DTC_FLAGS_sun8i-h3-nanopi-m1-plus := -@
+DTC_FLAGS_sun8i-h3-nanopi-m1 := -@
+DTC_FLAGS_sun8i-h3-nanopi-duo2 := -@
+DTC_FLAGS_sun8i-h3-orangepi-plus2e := -@
+DTC_FLAGS_sun8i-h3-orangepi-one := -@
+DTC_FLAGS_sun8i-h3-orangepi-plus := -@
+DTC_FLAGS_sun8i-h3-orangepi-2 := -@
+DTC_FLAGS_sun8i-h3-orangepi-zero-plus2 := -@
+DTC_FLAGS_sun8i-h3-nanopi-neo-air := -@
+DTC_FLAGS_sun8i-h3-zeropi := -@
+DTC_FLAGS_sun8i-h3-nanopi-neo := -@
+DTC_FLAGS_sun8i-h3-nanopi-r1 := -@
+DTC_FLAGS_sun8i-h3-orangepi-pc := -@
+DTC_FLAGS_sun8i-h3-bananapi-m2-plus-v1.2 := -@
+DTC_FLAGS_sun8i-h3-orangepi-pc-plus := -@
+DTC_FLAGS_sun8i-t113s-netcube-nagami-basic-carrier := -@
+DTC_FLAGS_sun8i-v3s-netcube-kumquat := -@
+dtb-$(CONFIG_MACH_SUN8I) += \
+	sun8i-a23-evb.dtb \
+	sun8i-a23-gt90h-v4.dtb \
+	sun8i-a23-inet86dz.dtb \
+	sun8i-a23-ippo-q8h-v5.dtb \
+	sun8i-a23-ippo-q8h-v1.2.dtb \
+	sun8i-a23-polaroid-mid2407pxe03.dtb \
+	sun8i-a23-polaroid-mid2809pxe04.dtb \
+	sun8i-a23-q8-tablet.dtb \
+	sun8i-a33-et-q8-v1.6.dtb \
+	sun8i-a33-ga10h-v1.1.dtb \
+	sun8i-a33-inet-d978-rev2.dtb \
+	sun8i-a33-ippo-q8h-v1.2.dtb \
+	sun8i-a33-olinuxino.dtb \
+	sun8i-a33-q8-tablet.dtb \
+	sun8i-a33-sinlinx-sina33.dtb \
+	sun8i-a33-vstar.dtb \
+	sun8i-a83t-allwinner-h8homlet-v2.dtb \
+	sun8i-a83t-bananapi-m3.dtb \
+	sun8i-a83t-cubietruck-plus.dtb \
+	sun8i-a83t-tbs-a711.dtb \
+	sun8i-h2-plus-bananapi-m2-zero.dtb \
+	sun8i-h2-plus-libretech-all-h3-cc.dtb \
+	sun8i-h2-plus-orangepi-r1.dtb \
+	sun8i-h2-plus-orangepi-zero.dtb \
+	sun8i-h2-plus-orangepi-zero-interface-board.dtb \
+	sun8i-h3-bananapi-m2-plus.dtb \
+	sun8i-h3-bananapi-m2-plus-v1.2.dtb \
+	sun8i-h3-beelink-x2.dtb \
+	sun8i-h3-libretech-all-h3-cc.dtb \
+	sun8i-h3-mapleboard-mp130.dtb \
+	sun8i-h3-nanopi-duo2.dtb \
+	sun8i-h3-nanopi-m1.dtb \
+	sun8i-h3-nanopi-m1-plus.dtb \
+	sun8i-h3-nanopi-neo.dtb \
+	sun8i-h3-nanopi-neo-air.dtb \
+	sun8i-h3-nanopi-r1.dtb \
+	sun8i-h3-orangepi-2.dtb \
+	sun8i-h3-orangepi-lite.dtb \
+	sun8i-h3-orangepi-one.dtb \
+	sun8i-h3-orangepi-pc.dtb \
+	sun8i-h3-orangepi-pc-plus.dtb \
+	sun8i-h3-orangepi-plus.dtb \
+	sun8i-h3-orangepi-plus2e.dtb \
+	sun8i-h3-orangepi-zero-plus2.dtb \
+	sun8i-h3-orangepi-zero-plus2-interface-board.dtb \
+	sun8i-h3-rervision-dvk.dtb \
+	sun8i-h3-zeropi.dtb \
+	sun8i-h3-emlid-neutis-n5h3-devboard.dtb \
+	sun8i-r16-bananapi-m2m.dtb \
+	sun8i-r16-nintendo-nes-classic.dtb \
+	sun8i-r16-nintendo-super-nes-classic.dtb \
+	sun8i-r16-parrot.dtb \
+	sun8i-r40-bananapi-m2-ultra.dtb \
+	sun8i-r40-oka40i-c.dtb \
+	sun8i-s3-elimo-initium.dtb \
+	sun8i-s3-lichee-zero-plus.dtb \
+	sun8i-s3-pinecube.dtb \
+	sun8i-t113s-mangopi-mq-r-t113.dtb \
+	sun8i-t113s-netcube-nagami-basic-carrier.dtb \
+	sun8i-t113s-netcube-nagami-keypad-carrier.dtb \
+	sun8i-t3-cqa3t-bv3.dtb \
+	sun8i-v3-sl631-imx179.dtb \
+	sun8i-v3s-anbernic-rg-nano.dtb \
+	sun8i-v3s-licheepi-zero.dtb \
+	sun8i-v3s-licheepi-zero-dock.dtb \
+	sun8i-v3s-netcube-kumquat.dtb \
+	sun8i-v40-bananapi-m2-berry.dtb
+sun8i-h2-plus-orangepi-zero-interface-board-dtbs += \
+	sun8i-h2-plus-orangepi-zero.dtb sun8i-orangepi-zero-interface-board.dtbo
+sun8i-h3-orangepi-zero-plus2-interface-board-dtbs += \
+	sun8i-h3-orangepi-zero-plus2.dtb sun8i-orangepi-zero-interface-board.dtbo
+dtb-$(CONFIG_MACH_SUN9I) += \
+	sun9i-a80-optimus.dtb \
+	sun9i-a80-cubieboard4.dtb
+dtb-$(CONFIG_MACH_SUNIV) += \
+	suniv-f1c100s-licheepi-nano.dtb \
+	suniv-f1c200s-lctech-pi.dtb \
+	suniv-f1c200s-popstick-v1.1.dtb
diff --git a/arch/arm/boot/dts/axp152.dtsi b/arch/arm/boot/dts/allwinner/axp152.dtsi
index f90ad6c64a07..f90ad6c64a07 100644
--- a/arch/arm/boot/dts/axp152.dtsi
+++ b/arch/arm/boot/dts/allwinner/axp152.dtsi
diff --git a/arch/arm/boot/dts/axp209.dtsi b/arch/arm/boot/dts/allwinner/axp209.dtsi
index ca240cd6f6c3..469d0f7d5185 100644
--- a/arch/arm/boot/dts/axp209.dtsi
+++ b/arch/arm/boot/dts/allwinner/axp209.dtsi
@@ -48,6 +48,13 @@
  * http://dl.linux-sunxi.org/AXP/AXP209%20Datasheet%20v1.0_cn.pdf
  */
 
+/ {
+	pmic-temp {
+		compatible = "iio-hwmon";
+		io-channels = <&axp_adc 4>; /* Internal temperature */
+	};
+};
+
 &axp209 {
 	compatible = "x-powers,axp209";
 	interrupt-controller;
diff --git a/arch/arm/boot/dts/axp223.dtsi b/arch/arm/boot/dts/allwinner/axp223.dtsi
index b91b6c1278c7..b91b6c1278c7 100644
--- a/arch/arm/boot/dts/axp223.dtsi
+++ b/arch/arm/boot/dts/allwinner/axp223.dtsi
diff --git a/arch/arm/boot/dts/axp22x.dtsi b/arch/arm/boot/dts/allwinner/axp22x.dtsi
index a020c12b2884..f79650afd0a7 100644
--- a/arch/arm/boot/dts/axp22x.dtsi
+++ b/arch/arm/boot/dts/allwinner/axp22x.dtsi
@@ -67,6 +67,12 @@
 		status = "disabled";
 	};
 
+	axp_gpio: gpio {
+		compatible = "x-powers,axp221-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	regulators {
 		/* Default work frequency for buck regulators */
 		x-powers,dcdc-freq = <3000>;
diff --git a/arch/arm/boot/dts/axp809.dtsi b/arch/arm/boot/dts/allwinner/axp809.dtsi
index ab8e5f2d9246..d134d4c00bd8 100644
--- a/arch/arm/boot/dts/axp809.dtsi
+++ b/arch/arm/boot/dts/allwinner/axp809.dtsi
@@ -50,4 +50,11 @@
 	compatible = "x-powers,axp809";
 	interrupt-controller;
 	#interrupt-cells = <1>;
+
+	axp_gpio: gpio {
+		compatible = "x-powers,axp809-gpio",
+			     "x-powers,axp221-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
 };
diff --git a/arch/arm/boot/dts/axp81x.dtsi b/arch/arm/boot/dts/allwinner/axp81x.dtsi
index b93387b0c1c3..ebaf1c3ce8db 100644
--- a/arch/arm/boot/dts/axp81x.dtsi
+++ b/arch/arm/boot/dts/allwinner/axp81x.dtsi
@@ -62,16 +62,6 @@
 		compatible = "x-powers,axp813-gpio";
 		gpio-controller;
 		#gpio-cells = <2>;
-
-		gpio0_ldo: gpio0-ldo-pin {
-			pins = "GPIO0";
-			function = "ldo";
-		};
-
-		gpio1_ldo: gpio1-ldo-pin {
-			pins = "GPIO1";
-			function = "ldo";
-		};
 	};
 
 	battery_power_supply: battery-power {
@@ -144,15 +134,11 @@
 		};
 
 		reg_ldo_io0: ldo-io0 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&gpio0_ldo>;
 			/* Disable by default to avoid conflicts with GPIO */
 			status = "disabled";
 		};
 
 		reg_ldo_io1: ldo-io1 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&gpio1_ldo>;
 			/* Disable by default to avoid conflicts with GPIO */
 			status = "disabled";
 		};
diff --git a/arch/arm/boot/dts/sun4i-a10-a1000.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-a1000.dts
index 20f9ed244851..20f9ed244851 100644
--- a/arch/arm/boot/dts/sun4i-a10-a1000.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-a1000.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-ba10-tvbox.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-ba10-tvbox.dts
index 816d534ac093..816d534ac093 100644
--- a/arch/arm/boot/dts/sun4i-a10-ba10-tvbox.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-ba10-tvbox.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-chuwi-v7-cw0825.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-chuwi-v7-cw0825.dts
index 74262988881c..74262988881c 100644
--- a/arch/arm/boot/dts/sun4i-a10-chuwi-v7-cw0825.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-chuwi-v7-cw0825.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-cubieboard.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-cubieboard.dts
index 0645d6064235..0645d6064235 100644
--- a/arch/arm/boot/dts/sun4i-a10-cubieboard.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-cubieboard.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-dserve-dsrv9703c.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-dserve-dsrv9703c.dts
index 63e77c05bfda..63e77c05bfda 100644
--- a/arch/arm/boot/dts/sun4i-a10-dserve-dsrv9703c.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-dserve-dsrv9703c.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-gemei-g9.dts
index ea7a59dcf8f9..ea7a59dcf8f9 100644
--- a/arch/arm/boot/dts/sun4i-a10-gemei-g9.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-gemei-g9.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-hackberry.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-hackberry.dts
index 47dea0922501..47dea0922501 100644
--- a/arch/arm/boot/dts/sun4i-a10-hackberry.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-hackberry.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-hyundai-a7hd.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-hyundai-a7hd.dts
index bf2044bac42f..bf2044bac42f 100644
--- a/arch/arm/boot/dts/sun4i-a10-hyundai-a7hd.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-hyundai-a7hd.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-inet1.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-inet1.dts
index 60e432a0ef1c..60e432a0ef1c 100644
--- a/arch/arm/boot/dts/sun4i-a10-inet1.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-inet1.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-inet97fv2.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-inet97fv2.dts
index 76016f2ca29d..76016f2ca29d 100644
--- a/arch/arm/boot/dts/sun4i-a10-inet97fv2.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-inet97fv2.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-inet9f-rev03.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-inet9f-rev03.dts
index 0a562b2cc5bc..62e7aa587f89 100644
--- a/arch/arm/boot/dts/sun4i-a10-inet9f-rev03.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-inet9f-rev03.dts
@@ -63,7 +63,7 @@
 		compatible = "gpio-keys-polled";
 		poll-interval = <20>;
 
-		left-joystick-left {
+		event-left-joystick-left {
 			label = "Left Joystick Left";
 			linux,code = <ABS_X>;
 			linux,input-type = <EV_ABS>;
@@ -71,7 +71,7 @@
 			gpios = <&pio 0 6 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA6 */
 		};
 
-		left-joystick-right {
+		event-left-joystick-right {
 			label = "Left Joystick Right";
 			linux,code = <ABS_X>;
 			linux,input-type = <EV_ABS>;
@@ -79,7 +79,7 @@
 			gpios = <&pio 0 5 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA5 */
 		};
 
-		left-joystick-up {
+		event-left-joystick-up {
 			label = "Left Joystick Up";
 			linux,code = <ABS_Y>;
 			linux,input-type = <EV_ABS>;
@@ -87,7 +87,7 @@
 			gpios = <&pio 0 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA8 */
 		};
 
-		left-joystick-down {
+		event-left-joystick-down {
 			label = "Left Joystick Down";
 			linux,code = <ABS_Y>;
 			linux,input-type = <EV_ABS>;
@@ -95,7 +95,7 @@
 			gpios = <&pio 0 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA9 */
 		};
 
-		right-joystick-left {
+		event-right-joystick-left {
 			label = "Right Joystick Left";
 			linux,code = <ABS_Z>;
 			linux,input-type = <EV_ABS>;
@@ -103,7 +103,7 @@
 			gpios = <&pio 0 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA1 */
 		};
 
-		right-joystick-right {
+		event-right-joystick-right {
 			label = "Right Joystick Right";
 			linux,code = <ABS_Z>;
 			linux,input-type = <EV_ABS>;
@@ -111,7 +111,7 @@
 			gpios = <&pio 0 0 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA0 */
 		};
 
-		right-joystick-up {
+		event-right-joystick-up {
 			label = "Right Joystick Up";
 			linux,code = <ABS_RZ>;
 			linux,input-type = <EV_ABS>;
@@ -119,7 +119,7 @@
 			gpios = <&pio 0 3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA3 */
 		};
 
-		right-joystick-down {
+		event-right-joystick-down {
 			label = "Right Joystick Down";
 			linux,code = <ABS_RZ>;
 			linux,input-type = <EV_ABS>;
@@ -127,7 +127,7 @@
 			gpios = <&pio 0 4 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA4 */
 		};
 
-		dpad-left {
+		event-dpad-left {
 			label = "DPad Left";
 			linux,code = <ABS_HAT0X>;
 			linux,input-type = <EV_ABS>;
@@ -135,7 +135,7 @@
 			gpios = <&pio 7 23 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PH23 */
 		};
 
-		dpad-right {
+		event-dpad-right {
 			label = "DPad Right";
 			linux,code = <ABS_HAT0X>;
 			linux,input-type = <EV_ABS>;
@@ -143,7 +143,7 @@
 			gpios = <&pio 7 24 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PH24 */
 		};
 
-		dpad-up {
+		event-dpad-up {
 			label = "DPad Up";
 			linux,code = <ABS_HAT0Y>;
 			linux,input-type = <EV_ABS>;
@@ -151,7 +151,7 @@
 			gpios = <&pio 7 25 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PH25 */
 		};
 
-		dpad-down {
+		event-dpad-down {
 			label = "DPad Down";
 			linux,code = <ABS_HAT0Y>;
 			linux,input-type = <EV_ABS>;
@@ -159,49 +159,49 @@
 			gpios = <&pio 7 26 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PH26 */
 		};
 
-		x {
+		event-x {
 			label = "Button X";
 			linux,code = <BTN_X>;
 			gpios = <&pio 0 16 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA16 */
 		};
 
-		y {
+		event-y {
 			label = "Button Y";
 			linux,code = <BTN_Y>;
 			gpios = <&pio 0 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA14 */
 		};
 
-		a {
+		event-a {
 			label = "Button A";
 			linux,code = <BTN_A>;
 			gpios = <&pio 0 17 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA17 */
 		};
 
-		b {
+		event-b {
 			label = "Button B";
 			linux,code = <BTN_B>;
 			gpios = <&pio 0 15 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA15 */
 		};
 
-		select {
+		event-select {
 			label = "Select Button";
 			linux,code = <BTN_SELECT>;
 			gpios = <&pio 0 11 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA11 */
 		};
 
-		start {
+		event-start {
 			label = "Start Button";
 			linux,code = <BTN_START>;
 			gpios = <&pio 0 12 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA12 */
 		};
 
-		top-left {
+		event-top-left {
 			label = "Top Left Button";
 			linux,code = <BTN_TL>;
 			gpios = <&pio 7 22 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PH22 */
 		};
 
-		top-right {
+		event-top-right {
 			label = "Top Right Button";
 			linux,code = <BTN_TR>;
 			gpios = <&pio 0 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA13 */
diff --git a/arch/arm/boot/dts/sun4i-a10-itead-iteaduino-plus.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-itead-iteaduino-plus.dts
index d4e319d16aae..d4e319d16aae 100644
--- a/arch/arm/boot/dts/sun4i-a10-itead-iteaduino-plus.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-itead-iteaduino-plus.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-jesurun-q5.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-jesurun-q5.dts
index 1aeb0bd5519e..1aeb0bd5519e 100644
--- a/arch/arm/boot/dts/sun4i-a10-jesurun-q5.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-jesurun-q5.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-marsboard.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-marsboard.dts
index 81fdb217d339..81fdb217d339 100644
--- a/arch/arm/boot/dts/sun4i-a10-marsboard.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-marsboard.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-mini-xplus.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-mini-xplus.dts
index f9d74e21031d..f9d74e21031d 100644
--- a/arch/arm/boot/dts/sun4i-a10-mini-xplus.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-mini-xplus.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-mk802.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-mk802.dts
index 059fe9c5d024..059fe9c5d024 100644
--- a/arch/arm/boot/dts/sun4i-a10-mk802.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-mk802.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-mk802ii.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-mk802ii.dts
index 17dcdf031118..17dcdf031118 100644
--- a/arch/arm/boot/dts/sun4i-a10-mk802ii.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-mk802ii.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-olinuxino-lime.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-olinuxino-lime.dts
index 83d283cf6633..d425d9ee83db 100644
--- a/arch/arm/boot/dts/sun4i-a10-olinuxino-lime.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-olinuxino-lime.dts
@@ -218,7 +218,7 @@
 &usbphy {
 	usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
 	usb0_vbus_det-gpios = <&pio 7 5 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH5 */
-	usb0_vbus-supply   = <&reg_usb0_vbus>;
+	usb0_vbus-supply = <&reg_usb0_vbus>;
 	usb1_vbus-supply = <&reg_usb1_vbus>;
 	usb2_vbus-supply = <&reg_usb2_vbus>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/sun4i-a10-pcduino.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-pcduino.dts
index 1ac82376baef..a332d61fd561 100644
--- a/arch/arm/boot/dts/sun4i-a10-pcduino.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-pcduino.dts
@@ -77,19 +77,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		back {
+		key-back {
 			label = "Key Back";
 			linux,code = <KEY_BACK>;
 			gpios = <&pio 7 17 GPIO_ACTIVE_LOW>;
 		};
 
-		home {
+		key-home {
 			label = "Key Home";
 			linux,code = <KEY_HOME>;
 			gpios = <&pio 7 18 GPIO_ACTIVE_LOW>;
 		};
 
-		menu {
+		key-menu {
 			label = "Key Menu";
 			linux,code = <KEY_MENU>;
 			gpios = <&pio 7 19 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/sun4i-a10-pcduino2.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-pcduino2.dts
index bc4f128965ed..bc4f128965ed 100644
--- a/arch/arm/boot/dts/sun4i-a10-pcduino2.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-pcduino2.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-pov-protab2-ips9.dts
index c32596947647..c32596947647 100644
--- a/arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-pov-protab2-ips9.dts
diff --git a/arch/arm/boot/dts/sun4i-a10-topwise-a721.dts b/arch/arm/boot/dts/allwinner/sun4i-a10-topwise-a721.dts
index 3628f12d2521..3628f12d2521 100644
--- a/arch/arm/boot/dts/sun4i-a10-topwise-a721.dts
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10-topwise-a721.dts
diff --git a/arch/arm/boot/dts/sun4i-a10.dtsi b/arch/arm/boot/dts/allwinner/sun4i-a10.dtsi
index 51a6464aab9a..51a6464aab9a 100644
--- a/arch/arm/boot/dts/sun4i-a10.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun4i-a10.dtsi
diff --git a/arch/arm/boot/dts/sun5i-a10s-auxtek-t003.dts b/arch/arm/boot/dts/allwinner/sun5i-a10s-auxtek-t003.dts
index 04b0e6d28769..04b0e6d28769 100644
--- a/arch/arm/boot/dts/sun5i-a10s-auxtek-t003.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a10s-auxtek-t003.dts
diff --git a/arch/arm/boot/dts/sun5i-a10s-auxtek-t004.dts b/arch/arm/boot/dts/allwinner/sun5i-a10s-auxtek-t004.dts
index 667bc2dc1ea9..667bc2dc1ea9 100644
--- a/arch/arm/boot/dts/sun5i-a10s-auxtek-t004.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a10s-auxtek-t004.dts
diff --git a/arch/arm/boot/dts/sun5i-a10s-mk802.dts b/arch/arm/boot/dts/allwinner/sun5i-a10s-mk802.dts
index d0219404c231..d0219404c231 100644
--- a/arch/arm/boot/dts/sun5i-a10s-mk802.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a10s-mk802.dts
diff --git a/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts b/arch/arm/boot/dts/allwinner/sun5i-a10s-olinuxino-micro.dts
index 5832bb31fc51..5832bb31fc51 100644
--- a/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a10s-olinuxino-micro.dts
diff --git a/arch/arm/boot/dts/sun5i-a10s-r7-tv-dongle.dts b/arch/arm/boot/dts/allwinner/sun5i-a10s-r7-tv-dongle.dts
index 964360f0610a..964360f0610a 100644
--- a/arch/arm/boot/dts/sun5i-a10s-r7-tv-dongle.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a10s-r7-tv-dongle.dts
diff --git a/arch/arm/boot/dts/sun5i-a10s-wobo-i5.dts b/arch/arm/boot/dts/allwinner/sun5i-a10s-wobo-i5.dts
index ef8baa992687..ef8baa992687 100644
--- a/arch/arm/boot/dts/sun5i-a10s-wobo-i5.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a10s-wobo-i5.dts
diff --git a/arch/arm/boot/dts/sun5i-a10s.dtsi b/arch/arm/boot/dts/allwinner/sun5i-a10s.dtsi
index 09c486b608b2..09c486b608b2 100644
--- a/arch/arm/boot/dts/sun5i-a10s.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun5i-a10s.dtsi
diff --git a/arch/arm/boot/dts/sun5i-a13-difrnce-dit4350.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-difrnce-dit4350.dts
index 894c4c4f9a1f..894c4c4f9a1f 100644
--- a/arch/arm/boot/dts/sun5i-a13-difrnce-dit4350.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a13-difrnce-dit4350.dts
diff --git a/arch/arm/boot/dts/sun5i-a13-empire-electronix-d709.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-empire-electronix-d709.dts
index d059388d7252..d059388d7252 100644
--- a/arch/arm/boot/dts/sun5i-a13-empire-electronix-d709.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a13-empire-electronix-d709.dts
diff --git a/arch/arm/boot/dts/sun5i-a13-empire-electronix-m712.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-empire-electronix-m712.dts
index b1e2afd9de52..b1e2afd9de52 100644
--- a/arch/arm/boot/dts/sun5i-a13-empire-electronix-m712.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a13-empire-electronix-m712.dts
diff --git a/arch/arm/boot/dts/sun5i-a13-hsg-h702.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-hsg-h702.dts
index 9b9f2a574851..9b9f2a574851 100644
--- a/arch/arm/boot/dts/sun5i-a13-hsg-h702.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a13-hsg-h702.dts
diff --git a/arch/arm/boot/dts/sun5i-a13-inet-98v-rev2.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-inet-98v-rev2.dts
index 439ae3b537df..439ae3b537df 100644
--- a/arch/arm/boot/dts/sun5i-a13-inet-98v-rev2.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a13-inet-98v-rev2.dts
diff --git a/arch/arm/boot/dts/sun5i-a13-licheepi-one.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-licheepi-one.dts
index 2ce361f8fede..3a6c4bd0a44f 100644
--- a/arch/arm/boot/dts/sun5i-a13-licheepi-one.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a13-licheepi-one.dts
@@ -67,18 +67,18 @@
 		compatible = "gpio-leds";
 
 		led-0 {
-			label ="licheepi:red:usr";
+			label = "licheepi:red:usr";
 			gpios = <&pio 2 5 GPIO_ACTIVE_LOW>;
 		};
 
 		led-1 {
-			label ="licheepi:green:usr";
+			label = "licheepi:green:usr";
 			gpios = <&pio 2 19 GPIO_ACTIVE_LOW>;
 			default-state = "on";
 		};
 
 		led-2 {
-			label ="licheepi:blue:usr";
+			label = "licheepi:blue:usr";
 			gpios = <&pio 2 4 GPIO_ACTIVE_LOW>;
 		};
 
diff --git a/arch/arm/boot/dts/sun5i-a13-olinuxino-micro.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-olinuxino-micro.dts
index bfe1075e62cc..bfe1075e62cc 100644
--- a/arch/arm/boot/dts/sun5i-a13-olinuxino-micro.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a13-olinuxino-micro.dts
diff --git a/arch/arm/boot/dts/sun5i-a13-olinuxino.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-olinuxino.dts
index fadeae3cd8bb..fadeae3cd8bb 100644
--- a/arch/arm/boot/dts/sun5i-a13-olinuxino.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a13-olinuxino.dts
diff --git a/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts
new file mode 100644
index 000000000000..ab8d138dc11d
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-614-plus.dts
@@ -0,0 +1,218 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2024 Denis Burkov <hitechshell@mail.ru>
+ */
+
+/dts-v1/;
+#include "sun5i-a13.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "PocketBook 614 Plus";
+	compatible = "pocketbook,614-plus", "allwinner,sun5i-a13";
+
+	aliases {
+		serial0 = &uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_POWER;
+			linux,default-trigger = "default-on";
+			gpios = <&pio 4 8 GPIO_ACTIVE_LOW>; /* PE8 */
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-0 {
+			label = "Right";
+			linux,code = <KEY_NEXT>;
+			gpios = <&pio 6 9 GPIO_ACTIVE_LOW>; /* PG9 */
+		};
+
+		key-1 {
+			label = "Left";
+			linux,code = <KEY_PREVIOUS>;
+			gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 */
+		};
+	};
+
+	reg_3v3_mmc0: regulator-mmc0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-mmc0";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&pio 4 4 GPIO_ACTIVE_LOW>; /* PE4 */
+		vin-supply = <&reg_vcc3v3>;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	axp209: pmic@34 {
+		compatible = "x-powers,axp209";
+		reg = <0x34>;
+		interrupts = <0>;
+	};
+};
+
+#include "axp209.dtsi"
+
+&i2c1 {
+	status = "okay";
+
+	pcf8563: rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+		#clock-cells = <0>;
+	};
+};
+
+&lradc {
+	vref-supply = <&reg_ldo2>;
+	status = "okay";
+
+	button-300 {
+		label = "Down";
+		linux,code = <KEY_DOWN>;
+		channel = <0>;
+		voltage = <300000>;
+	};
+
+	button-700 {
+		label = "Up";
+		linux,code = <KEY_UP>;
+		channel = <0>;
+		voltage = <700000>;
+	};
+
+	button-1000 {
+		label = "Left";
+		linux,code = <KEY_LEFT>;
+		channel = <0>;
+		voltage = <1000000>;
+	};
+
+	button-1200 {
+		label = "Menu";
+		linux,code = <KEY_MENU>;
+		channel = <0>;
+		voltage = <1200000>;
+	};
+
+	button-1500 {
+		label = "Right";
+		linux,code = <KEY_RIGHT>;
+		channel = <0>;
+		voltage = <1500000>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_3v3_mmc0>;
+	bus-width = <4>;
+	cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
+	status = "okay";
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_4bit_pc_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&otg_sram {
+	status = "okay";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1500000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-int-dll";
+};
+
+&reg_ldo1 {
+	regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
+&reg_usb0_vbus {
+	status = "okay";
+	gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+};
+
+&reg_usb1_vbus {
+	gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pg_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb_power_supply {
+	status = "okay";
+};
+
+&battery_power_supply {
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
+	usb0_vbus_det-gpios = <&axp_gpio 1 GPIO_ACTIVE_HIGH>;
+	usb0_vbus-supply = <&reg_usb0_vbus>;
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sun5i-a13-pocketbook-touch-lux-3.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-touch-lux-3.dts
index d60407772e5d..d60407772e5d 100644
--- a/arch/arm/boot/dts/sun5i-a13-pocketbook-touch-lux-3.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a13-pocketbook-touch-lux-3.dts
diff --git a/arch/arm/boot/dts/sun5i-a13-q8-tablet.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-q8-tablet.dts
index f9fc1c8b60b8..f9fc1c8b60b8 100644
--- a/arch/arm/boot/dts/sun5i-a13-q8-tablet.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a13-q8-tablet.dts
diff --git a/arch/arm/boot/dts/sun5i-a13-utoo-p66.dts b/arch/arm/boot/dts/allwinner/sun5i-a13-utoo-p66.dts
index be486d28d04f..be486d28d04f 100644
--- a/arch/arm/boot/dts/sun5i-a13-utoo-p66.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-a13-utoo-p66.dts
diff --git a/arch/arm/boot/dts/sun5i-a13.dtsi b/arch/arm/boot/dts/allwinner/sun5i-a13.dtsi
index 3325ab07094a..2c9152b151be 100644
--- a/arch/arm/boot/dts/sun5i-a13.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun5i-a13.dtsi
@@ -62,14 +62,14 @@
 			};
 
 			trips {
-				cpu_alert0: cpu_alert0 {
+				cpu_alert0: cpu-alert0 {
 					/* milliCelsius */
 					temperature = <85000>;
 					hysteresis = <2000>;
 					type = "passive";
 				};
 
-				cpu_crit: cpu_crit {
+				cpu_crit: cpu-crit {
 					/* milliCelsius */
 					temperature = <100000>;
 					hysteresis = <2000>;
diff --git a/arch/arm/boot/dts/sun5i-gr8-chip-pro.dts b/arch/arm/boot/dts/allwinner/sun5i-gr8-chip-pro.dts
index a32cde3e32eb..ffbd99c176db 100644
--- a/arch/arm/boot/dts/sun5i-gr8-chip-pro.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-gr8-chip-pro.dts
@@ -70,14 +70,14 @@
 	leds {
 		compatible = "gpio-leds";
 
-		status {
+		led-0 {
 			label = "chip-pro:white:status";
 			gpios = <&axp_gpio 2 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 		};
 	};
 
-	mmc0_pwrseq: mmc0_pwrseq {
+	mmc0_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&pio 1 10 GPIO_ACTIVE_LOW>; /* PB10 */
 	};
diff --git a/arch/arm/boot/dts/sun5i-gr8-evb.dts b/arch/arm/boot/dts/allwinner/sun5i-gr8-evb.dts
index f4fe258ef06d..f4fe258ef06d 100644
--- a/arch/arm/boot/dts/sun5i-gr8-evb.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-gr8-evb.dts
diff --git a/arch/arm/boot/dts/sun5i-gr8.dtsi b/arch/arm/boot/dts/allwinner/sun5i-gr8.dtsi
index 98a8fd5e89e8..98a8fd5e89e8 100644
--- a/arch/arm/boot/dts/sun5i-gr8.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun5i-gr8.dtsi
diff --git a/arch/arm/boot/dts/sun5i-r8-chip.dts b/arch/arm/boot/dts/allwinner/sun5i-r8-chip.dts
index 4bf4943d4eb7..8c784a2c086e 100644
--- a/arch/arm/boot/dts/sun5i-r8-chip.dts
+++ b/arch/arm/boot/dts/allwinner/sun5i-r8-chip.dts
@@ -70,14 +70,14 @@
 	leds {
 		compatible = "gpio-leds";
 
-		status {
+		led-0 {
 			label = "chip:white:status";
 			gpios = <&axp_gpio 2 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 		};
 	};
 
-	mmc0_pwrseq: mmc0_pwrseq {
+	mmc0_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&pio 2 19 GPIO_ACTIVE_LOW>; /* PC19 */
 	};
@@ -255,6 +255,12 @@
 	pinctrl-0 = <&uart3_pg_pins>,
 		    <&uart3_cts_rts_pg_pins>;
 	status = "okay";
+
+	bluetooth {
+		compatible = "realtek,rtl8723bs-bt";
+		device-wake-gpios = <&axp_gpio 3 GPIO_ACTIVE_HIGH>;
+		host-wake-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
+	};
 };
 
 &usb_otg {
diff --git a/arch/arm/boot/dts/sun5i-r8.dtsi b/arch/arm/boot/dts/allwinner/sun5i-r8.dtsi
index de35dbcd1191..de35dbcd1191 100644
--- a/arch/arm/boot/dts/sun5i-r8.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun5i-r8.dtsi
diff --git a/arch/arm/boot/dts/sun5i-reference-design-tablet.dtsi b/arch/arm/boot/dts/allwinner/sun5i-reference-design-tablet.dtsi
index 6847f66699ac..6847f66699ac 100644
--- a/arch/arm/boot/dts/sun5i-reference-design-tablet.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun5i-reference-design-tablet.dtsi
diff --git a/arch/arm/boot/dts/sun5i.dtsi b/arch/arm/boot/dts/allwinner/sun5i.dtsi
index 250d6b87ab4d..d7c7b454a11a 100644
--- a/arch/arm/boot/dts/sun5i.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun5i.dtsi
@@ -286,7 +286,7 @@
 			clock-names = "ahb",
 				      "tcon-ch0",
 				      "tcon-ch1";
-			clock-output-names = "tcon-pixel-clock";
+			clock-output-names = "tcon-data-clock";
 			#clock-cells = <0>;
 			status = "disabled";
 
@@ -517,6 +517,15 @@
 				bias-pull-up;
 			};
 
+			/omit-if-no-ref/
+			mmc2_4bit_pe_pins: mmc2-4bit-pe-pins {
+				pins = "PE4", "PE5", "PE6", "PE7",
+				       "PE8", "PE9";
+				function = "mmc2";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
 			mmc2_8bit_pins: mmc2-8bit-pins {
 				pins = "PC6", "PC7", "PC8", "PC9",
 				       "PC10", "PC11", "PC12", "PC13",
diff --git a/arch/arm/boot/dts/sun6i-a31-app4-evb1.dts b/arch/arm/boot/dts/allwinner/sun6i-a31-app4-evb1.dts
index 32d22025ac99..32d22025ac99 100644
--- a/arch/arm/boot/dts/sun6i-a31-app4-evb1.dts
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31-app4-evb1.dts
diff --git a/arch/arm/boot/dts/sun6i-a31-colombus.dts b/arch/arm/boot/dts/allwinner/sun6i-a31-colombus.dts
index 93a15eaaa8cb..93a15eaaa8cb 100644
--- a/arch/arm/boot/dts/sun6i-a31-colombus.dts
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31-colombus.dts
diff --git a/arch/arm/boot/dts/sun6i-a31-hummingbird.dts b/arch/arm/boot/dts/allwinner/sun6i-a31-hummingbird.dts
index 236ebfc06192..5bce7a32651e 100644
--- a/arch/arm/boot/dts/sun6i-a31-hummingbird.dts
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31-hummingbird.dts
@@ -109,7 +109,7 @@
 		};
 	};
 
-	reg_vga_3v3: vga_3v3_regulator {
+	reg_vga_3v3: vga-3v3-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "vga-3v3";
 		regulator-min-microvolt = <3300000>;
@@ -119,7 +119,7 @@
 		gpio = <&pio 7 25 GPIO_ACTIVE_HIGH>; /* PH25 */
 	};
 
-	wifi_pwrseq: wifi_pwrseq {
+	wifi_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 */
 	};
diff --git a/arch/arm/boot/dts/sun6i-a31-i7.dts b/arch/arm/boot/dts/allwinner/sun6i-a31-i7.dts
index 744723d956f0..744723d956f0 100644
--- a/arch/arm/boot/dts/sun6i-a31-i7.dts
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31-i7.dts
diff --git a/arch/arm/boot/dts/sun6i-a31-m9.dts b/arch/arm/boot/dts/allwinner/sun6i-a31-m9.dts
index 7d2eaaf5c33e..7d2eaaf5c33e 100644
--- a/arch/arm/boot/dts/sun6i-a31-m9.dts
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31-m9.dts
diff --git a/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts b/arch/arm/boot/dts/allwinner/sun6i-a31-mele-a1000g-quad.dts
index 83611434270c..83611434270c 100644
--- a/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31-mele-a1000g-quad.dts
diff --git a/arch/arm/boot/dts/sun6i-a31.dtsi b/arch/arm/boot/dts/allwinner/sun6i-a31.dtsi
index 715d74854449..f0145d6b9c53 100644
--- a/arch/arm/boot/dts/sun6i-a31.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31.dtsi
@@ -46,6 +46,7 @@
 #include <dt-bindings/thermal/thermal.h>
 
 #include <dt-bindings/clock/sun6i-a31-ccu.h>
+#include <dt-bindings/clock/sun6i-rtc.h>
 #include <dt-bindings/reset/sun6i-a31-ccu.h>
 
 / {
@@ -178,14 +179,14 @@
 			};
 
 			trips {
-				cpu_alert0: cpu_alert0 {
+				cpu_alert0: cpu-alert0 {
 					/* milliCelsius */
 					temperature = <70000>;
 					hysteresis = <2000>;
 					type = "passive";
 				};
 
-				cpu_crit: cpu_crit {
+				cpu_crit: cpu-crit {
 					/* milliCelsius */
 					temperature = <100000>;
 					hysteresis = <2000>;
@@ -598,7 +599,7 @@
 		ccu: clock@1c20000 {
 			compatible = "allwinner,sun6i-a31-ccu";
 			reg = <0x01c20000 0x400>;
-			clocks = <&osc24M>, <&rtc 0>;
+			clocks = <&osc24M>, <&rtc CLK_OSC32K>;
 			clock-names = "hosc", "losc";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -612,7 +613,8 @@
 				     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu CLK_APB1_PIO>, <&osc24M>, <&rtc 0>;
+			clocks = <&ccu CLK_APB1_PIO>, <&osc24M>,
+				 <&rtc CLK_OSC32K>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			interrupt-controller;
@@ -820,7 +822,7 @@
 			clocks = <&ccu CLK_APB2_UART0>;
 			resets = <&ccu RST_APB2_UART0>;
 			dmas = <&dma 6>, <&dma 6>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -833,7 +835,7 @@
 			clocks = <&ccu CLK_APB2_UART1>;
 			resets = <&ccu RST_APB2_UART1>;
 			dmas = <&dma 7>, <&dma 7>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -846,7 +848,7 @@
 			clocks = <&ccu CLK_APB2_UART2>;
 			resets = <&ccu RST_APB2_UART2>;
 			dmas = <&dma 8>, <&dma 8>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -859,7 +861,7 @@
 			clocks = <&ccu CLK_APB2_UART3>;
 			resets = <&ccu RST_APB2_UART3>;
 			dmas = <&dma 9>, <&dma 9>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -872,7 +874,7 @@
 			clocks = <&ccu CLK_APB2_UART4>;
 			resets = <&ccu RST_APB2_UART4>;
 			dmas = <&dma 10>, <&dma 10>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -885,7 +887,7 @@
 			clocks = <&ccu CLK_APB2_UART5>;
 			resets = <&ccu RST_APB2_UART5>;
 			dmas = <&dma 22>, <&dma 22>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -1316,16 +1318,16 @@
 			compatible = "allwinner,sun6i-a31-prcm";
 			reg = <0x01f01400 0x200>;
 
-			ar100: ar100_clk {
+			ar100: ar100-clk {
 				compatible = "allwinner,sun6i-a31-ar100-clk";
 				#clock-cells = <0>;
-				clocks = <&rtc 0>, <&osc24M>,
+				clocks = <&rtc CLK_OSC32K>, <&osc24M>,
 					 <&ccu CLK_PLL_PERIPH>,
 					 <&ccu CLK_PLL_PERIPH>;
 				clock-output-names = "ar100";
 			};
 
-			ahb0: ahb0_clk {
+			ahb0: ahb0-clk {
 				compatible = "fixed-factor-clock";
 				#clock-cells = <0>;
 				clock-div = <1>;
@@ -1334,14 +1336,14 @@
 				clock-output-names = "ahb0";
 			};
 
-			apb0: apb0_clk {
+			apb0: apb0-clk {
 				compatible = "allwinner,sun6i-a31-apb0-clk";
 				#clock-cells = <0>;
 				clocks = <&ahb0>;
 				clock-output-names = "apb0";
 			};
 
-			apb0_gates: apb0_gates_clk {
+			apb0_gates: apb0-gates-clk {
 				compatible = "allwinner,sun6i-a31-apb0-gates-clk";
 				#clock-cells = <1>;
 				clocks = <&apb0>;
@@ -1351,14 +1353,14 @@
 						"apb0_i2c";
 			};
 
-			ir_clk: ir_clk {
+			ir_clk: ir-clk {
 				#clock-cells = <0>;
 				compatible = "allwinner,sun4i-a10-mod0-clk";
-				clocks = <&rtc 0>, <&osc24M>;
+				clocks = <&rtc CLK_OSC32K>, <&osc24M>;
 				clock-output-names = "ir";
 			};
 
-			apb0_rst: apb0_rst {
+			apb0_rst: apb0-rst {
 				compatible = "allwinner,sun6i-a31-clock-reset";
 				#reset-cells = <1>;
 			};
@@ -1385,9 +1387,8 @@
 			interrupt-parent = <&r_intc>;
 			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&apb0_gates 0>, <&osc24M>, <&rtc 0>;
+			clocks = <&apb0_gates 0>, <&osc24M>, <&rtc CLK_OSC32K>;
 			clock-names = "apb", "hosc", "losc";
-			resets = <&apb0_rst 0>;
 			gpio-controller;
 			interrupt-controller;
 			#interrupt-cells = <3>;
diff --git a/arch/arm/boot/dts/sun6i-a31s-colorfly-e708-q1.dts b/arch/arm/boot/dts/allwinner/sun6i-a31s-colorfly-e708-q1.dts
index a2ef7846e2c8..a2ef7846e2c8 100644
--- a/arch/arm/boot/dts/sun6i-a31s-colorfly-e708-q1.dts
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31s-colorfly-e708-q1.dts
diff --git a/arch/arm/boot/dts/sun6i-a31s-cs908.dts b/arch/arm/boot/dts/allwinner/sun6i-a31s-cs908.dts
index 1d15e15011c6..1d15e15011c6 100644
--- a/arch/arm/boot/dts/sun6i-a31s-cs908.dts
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31s-cs908.dts
diff --git a/arch/arm/boot/dts/sun6i-a31s-inet-q972.dts b/arch/arm/boot/dts/allwinner/sun6i-a31s-inet-q972.dts
index c5e2c55cdc63..c5e2c55cdc63 100644
--- a/arch/arm/boot/dts/sun6i-a31s-inet-q972.dts
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31s-inet-q972.dts
diff --git a/arch/arm/boot/dts/sun6i-a31s-primo81.dts b/arch/arm/boot/dts/allwinner/sun6i-a31s-primo81.dts
index b32b70ada7fd..b32b70ada7fd 100644
--- a/arch/arm/boot/dts/sun6i-a31s-primo81.dts
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31s-primo81.dts
diff --git a/arch/arm/boot/dts/sun6i-a31s-sina31s-core.dtsi b/arch/arm/boot/dts/allwinner/sun6i-a31s-sina31s-core.dtsi
index 227ad489731c..227ad489731c 100644
--- a/arch/arm/boot/dts/sun6i-a31s-sina31s-core.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31s-sina31s-core.dtsi
diff --git a/arch/arm/boot/dts/sun6i-a31s-sina31s.dts b/arch/arm/boot/dts/allwinner/sun6i-a31s-sina31s.dts
index 0af48e143b66..56956352914d 100644
--- a/arch/arm/boot/dts/sun6i-a31s-sina31s.dts
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31s-sina31s.dts
@@ -67,7 +67,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		status {
+		led-0 {
 			label = "sina31s:status:usr";
 			gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>; /* PH13 */
 		};
diff --git a/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts b/arch/arm/boot/dts/allwinner/sun6i-a31s-sinovoip-bpi-m2.dts
index 96554ab4f6d3..f63d67ec9887 100644
--- a/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31s-sinovoip-bpi-m2.dts
@@ -75,7 +75,7 @@
 		};
 	};
 
-	mmc2_pwrseq: mmc2_pwrseq {
+	mmc2_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 8 GPIO_ACTIVE_LOW>; /* PL8 WIFI_EN */
 	};
diff --git a/arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts b/arch/arm/boot/dts/allwinner/sun6i-a31s-yones-toptech-bs1078-v2.dts
index 0b61f5368d44..0b61f5368d44 100644
--- a/arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31s-yones-toptech-bs1078-v2.dts
diff --git a/arch/arm/boot/dts/sun6i-a31s.dtsi b/arch/arm/boot/dts/allwinner/sun6i-a31s.dtsi
index 97e2c51d0aea..97e2c51d0aea 100644
--- a/arch/arm/boot/dts/sun6i-a31s.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun6i-a31s.dtsi
diff --git a/arch/arm/boot/dts/sun6i-reference-design-tablet.dtsi b/arch/arm/boot/dts/allwinner/sun6i-reference-design-tablet.dtsi
index f38d19c6be8c..f38d19c6be8c 100644
--- a/arch/arm/boot/dts/sun6i-reference-design-tablet.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun6i-reference-design-tablet.dtsi
diff --git a/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-bananapi-m1-plus.dts
index caa935ca4f19..f2d7fab9978d 100644
--- a/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-bananapi-m1-plus.dts
@@ -86,7 +86,7 @@
 		};
 	};
 
-	mmc3_pwrseq: mmc3_pwrseq {
+	mmc3_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 WL-PMU-EN */
 	};
diff --git a/arch/arm/boot/dts/sun7i-a20-bananapi.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-bananapi.dts
index 46ecf9db2324..d8b362c9661a 100644
--- a/arch/arm/boot/dts/sun7i-a20-bananapi.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-bananapi.dts
@@ -48,6 +48,7 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/leds/common.h>
 
 / {
 	model = "LeMaker Banana Pi";
@@ -169,6 +170,32 @@
 &gmac_mdio {
 	phy1: ethernet-phy@1 {
 		reg = <1>;
+
+		leds {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			led@0 {
+				reg = <0>;
+				color = <LED_COLOR_ID_GREEN>;
+				function = LED_FUNCTION_LAN;
+				linux,default-trigger = "netdev";
+			};
+
+			led@1 {
+				reg = <1>;
+				color = <LED_COLOR_ID_AMBER>;
+				function = LED_FUNCTION_LAN;
+				linux,default-trigger = "netdev";
+			};
+
+			led@2 {
+				reg = <2>;
+				color = <LED_COLOR_ID_BLUE>;
+				function = LED_FUNCTION_LAN;
+				linux,default-trigger = "netdev";
+			};
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/sun7i-a20-bananapro.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-bananapro.dts
index e22f0e8bb17a..e22f0e8bb17a 100644
--- a/arch/arm/boot/dts/sun7i-a20-bananapro.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-bananapro.dts
diff --git a/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-cubieboard2.dts
index e35e6990c4b2..e35e6990c4b2 100644
--- a/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-cubieboard2.dts
diff --git a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-cubietruck.dts
index 52160e368304..be9b31d0f4b5 100644
--- a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-cubietruck.dts
@@ -96,7 +96,7 @@
 		};
 	};
 
-	mmc3_pwrseq: mmc3_pwrseq {
+	mmc3_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&pio 7 9 GPIO_ACTIVE_LOW>; /* PH9 WIFI_EN */
 		clocks = <&ccu CLK_OUT_A>;
diff --git a/arch/arm/boot/dts/sun7i-a20-haoyu-marsboard.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-haoyu-marsboard.dts
index 097e479c2772..097e479c2772 100644
--- a/arch/arm/boot/dts/sun7i-a20-haoyu-marsboard.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-haoyu-marsboard.dts
diff --git a/arch/arm/boot/dts/sun7i-a20-hummingbird.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-hummingbird.dts
index 3def2a330598..f1e26b75cd90 100644
--- a/arch/arm/boot/dts/sun7i-a20-hummingbird.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-hummingbird.dts
@@ -65,7 +65,7 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	reg_mmc3_vdd: mmc3_vdd {
+	reg_mmc3_vdd: regulator-mmc3-vdd {
 		compatible = "regulator-fixed";
 		regulator-name = "mmc3_vdd";
 		regulator-min-microvolt = <3000000>;
@@ -74,7 +74,7 @@
 		gpio = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
 	};
 
-	reg_gmac_vdd: gmac_vdd {
+	reg_gmac_vdd: regulator-gmac-vdd {
 		compatible = "regulator-fixed";
 		regulator-name = "gmac_vdd";
 		regulator-min-microvolt = <3000000>;
diff --git a/arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-i12-tvbox.dts
index b21ddd0ec1c2..b21ddd0ec1c2 100644
--- a/arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-i12-tvbox.dts
diff --git a/arch/arm/boot/dts/allwinner/sun7i-a20-icnova-a20-adb4006.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-icnova-a20-adb4006.dts
new file mode 100644
index 000000000000..577ead1d02a0
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-icnova-a20-adb4006.dts
@@ -0,0 +1,137 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// Copyright (C) 2023 In-Circuit GmbH
+
+/dts-v1/;
+
+#include "sun7i-a20-icnova-a20.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "In-Circuit ICnova A20 ADB4006";
+	compatible = "incircuit,icnova-a20-adb4006", "incircuit,icnova-a20",
+		     "allwinner,sun7i-a20";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_YELLOW>;
+			gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; /* PH21 */
+			default-state = "on";
+		};
+
+		led-1 {
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>; /* PH20 */
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&ahci {
+	target-supply = <&reg_ahci_5v>;
+	status = "okay";
+};
+
+&codec {
+	status = "okay";
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&otg_sram {
+	status = "okay";
+};
+
+&reg_ahci_5v {
+	status = "okay";
+};
+
+&ac_power_supply {
+	status = "okay";
+};
+
+&reg_usb1_vbus {
+	status = "okay";
+};
+
+&reg_usb2_vbus {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pb_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+	usb0_vbus_det-gpios = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	usb2_vbus-supply = <&reg_usb2_vbus>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/allwinner/sun7i-a20-icnova-a20.dtsi b/arch/arm/boot/dts/allwinner/sun7i-a20-icnova-a20.dtsi
new file mode 100644
index 000000000000..46616c6bc899
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-icnova-a20.dtsi
@@ -0,0 +1,62 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// Copyright (C) 2023 In-Circuit GmbH
+
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&gmac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac_mii_pins>;
+	phy-handle = <&phy1>;
+	phy-mode = "mii";
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	axp209: pmic@34 {
+		reg = <0x34>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&gmac_mdio {
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
+#include "axp209.dtsi"
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-int-dll";
+};
+
+&reg_ldo1 {
+	regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
diff --git a/arch/arm/boot/dts/sun7i-a20-icnova-swac.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-icnova-swac.dts
index 413505f45a81..413505f45a81 100644
--- a/arch/arm/boot/dts/sun7i-a20-icnova-swac.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-icnova-swac.dts
diff --git a/arch/arm/boot/dts/sun7i-a20-itead-ibox.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-itead-ibox.dts
index 8ff83016ff5a..8ff83016ff5a 100644
--- a/arch/arm/boot/dts/sun7i-a20-itead-ibox.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-itead-ibox.dts
diff --git a/arch/arm/boot/dts/sun7i-a20-lamobo-r1.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-lamobo-r1.dts
index 97518afe4658..97518afe4658 100644
--- a/arch/arm/boot/dts/sun7i-a20-lamobo-r1.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-lamobo-r1.dts
diff --git a/arch/arm/boot/dts/sun7i-a20-linutronix-testbox-v2.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-linutronix-testbox-v2.dts
index da5a2eea4ce3..da5a2eea4ce3 100644
--- a/arch/arm/boot/dts/sun7i-a20-linutronix-testbox-v2.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-linutronix-testbox-v2.dts
diff --git a/arch/arm/boot/dts/sun7i-a20-m3.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-m3.dts
index f161d5238860..f161d5238860 100644
--- a/arch/arm/boot/dts/sun7i-a20-m3.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-m3.dts
diff --git a/arch/arm/boot/dts/sun7i-a20-mk808c.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-mk808c.dts
index 1491c603f661..1491c603f661 100644
--- a/arch/arm/boot/dts/sun7i-a20-mk808c.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-mk808c.dts
diff --git a/arch/arm/boot/dts/sun7i-a20-olimex-som-evb-emmc.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-olimex-som-evb-emmc.dts
index 20bf09b2226c..fb835730bbc4 100644
--- a/arch/arm/boot/dts/sun7i-a20-olimex-som-evb-emmc.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-olimex-som-evb-emmc.dts
@@ -14,7 +14,7 @@
 	model = "Olimex A20-Olimex-SOM-EVB-eMMC";
 	compatible = "olimex,a20-olimex-som-evb-emmc", "allwinner,sun7i-a20";
 
-	mmc2_pwrseq: mmc2_pwrseq {
+	mmc2_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-emmc";
 		reset-gpios = <&pio 2 18 GPIO_ACTIVE_LOW>;
 	};
diff --git a/arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-olimex-som-evb.dts
index f05ee32bc9cb..f05ee32bc9cb 100644
--- a/arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-olimex-som-evb.dts
diff --git a/arch/arm/boot/dts/sun7i-a20-olimex-som204-evb-emmc.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-olimex-som204-evb-emmc.dts
index a59755a2e7a9..e8977c2fe798 100644
--- a/arch/arm/boot/dts/sun7i-a20-olimex-som204-evb-emmc.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-olimex-som204-evb-emmc.dts
@@ -13,7 +13,7 @@
 	model = "Olimex A20-SOM204-EVB-eMMC";
 	compatible = "olimex,a20-olimex-som204-evb-emmc", "allwinner,sun7i-a20";
 
-	mmc2_pwrseq: mmc2_pwrseq {
+	mmc2_pwrseq: pwrseq-1 {
 		compatible = "mmc-pwrseq-emmc";
 		reset-gpios = <&pio 2 16 GPIO_ACTIVE_LOW>;
 	};
diff --git a/arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-olimex-som204-evb.dts
index 54af6c18075b..a55406657449 100644
--- a/arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-olimex-som204-evb.dts
@@ -65,7 +65,7 @@
 		};
 	};
 
-	rtl_pwrseq: rtl_pwrseq {
+	rtl_pwrseq: pwrseq-0 {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&pio 6 9 GPIO_ACTIVE_LOW>;
 	};
@@ -177,7 +177,7 @@
 	non-removable;
 	status = "okay";
 
-	rtl8723bs: sdio_wifi@1 {
+	rtl8723bs: wifi@1 {
 		reg = <1>;
 	};
 };
diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime-emmc.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-lime-emmc.dts
index 033cab3443f8..033cab3443f8 100644
--- a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime-emmc.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-lime-emmc.dts
diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-lime.dts
index 92938d022295..92938d022295 100644
--- a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-lime.dts
diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2-emmc.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-lime2-emmc.dts
index decb014a382b..decb014a382b 100644
--- a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2-emmc.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-lime2-emmc.dts
diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-lime2.dts
index ecb91fb899ff..435a189332e8 100644
--- a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-lime2.dts
@@ -82,7 +82,7 @@
 		};
 	};
 
-	reg_axp_ipsout: axp_ipsout {
+	reg_axp_ipsout: regulator-axp-ipsout {
 		compatible = "regulator-fixed";
 		regulator-name = "axp-ipsout";
 		regulator-min-microvolt = <5000000>;
diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro-emmc.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-micro-emmc.dts
index 2337b44a88aa..2337b44a88aa 100644
--- a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro-emmc.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-micro-emmc.dts
diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-micro.dts
index a1b89b2a2999..a1b89b2a2999 100644
--- a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-olinuxino-micro.dts
diff --git a/arch/arm/boot/dts/sun7i-a20-orangepi-mini.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-orangepi-mini.dts
index 84efa01e7cba..84efa01e7cba 100644
--- a/arch/arm/boot/dts/sun7i-a20-orangepi-mini.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-orangepi-mini.dts
diff --git a/arch/arm/boot/dts/sun7i-a20-orangepi.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-orangepi.dts
index 5d77f1d9818f..5d77f1d9818f 100644
--- a/arch/arm/boot/dts/sun7i-a20-orangepi.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-orangepi.dts
diff --git a/arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-pcduino3-nano.dts
index e40ecb48d726..e40ecb48d726 100644
--- a/arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-pcduino3-nano.dts
diff --git a/arch/arm/boot/dts/sun7i-a20-pcduino3.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-pcduino3.dts
index 4f8d55d3ba79..928b86a95f34 100644
--- a/arch/arm/boot/dts/sun7i-a20-pcduino3.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-pcduino3.dts
@@ -78,19 +78,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		back {
+		key-back {
 			label = "Key Back";
 			linux,code = <KEY_BACK>;
 			gpios = <&pio 7 17 GPIO_ACTIVE_LOW>;
 		};
 
-		home {
+		key-home {
 			label = "Key Home";
 			linux,code = <KEY_HOME>;
 			gpios = <&pio 7 18 GPIO_ACTIVE_LOW>;
 		};
 
-		menu {
+		key-menu {
 			label = "Key Menu";
 			linux,code = <KEY_MENU>;
 			gpios = <&pio 7 19 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-wexler-tab7200.dts
index fef02fcbbdf8..fef02fcbbdf8 100644
--- a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-wexler-tab7200.dts
diff --git a/arch/arm/boot/dts/sun7i-a20-wits-pro-a20-dkt.dts b/arch/arm/boot/dts/allwinner/sun7i-a20-wits-pro-a20-dkt.dts
index 3bfae98f3cc3..29199b6a3b4a 100644
--- a/arch/arm/boot/dts/sun7i-a20-wits-pro-a20-dkt.dts
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20-wits-pro-a20-dkt.dts
@@ -60,7 +60,7 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	mmc3_pwrseq: mmc3_pwrseq {
+	mmc3_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&pio 7 9 GPIO_ACTIVE_LOW>; /* PH9 WIFI_EN */
 	};
diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/allwinner/sun7i-a20.dtsi
index 5574299685ab..5f44f09c5545 100644
--- a/arch/arm/boot/dts/sun7i-a20.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun7i-a20.dtsi
@@ -153,14 +153,14 @@
 			};
 
 			trips {
-				cpu_alert0: cpu_alert0 {
+				cpu_alert0: cpu-alert0 {
 					/* milliCelsius */
 					temperature = <75000>;
 					hysteresis = <2000>;
 					type = "passive";
 				};
 
-				cpu_crit: cpu_crit {
+				cpu_crit: cpu-crit {
 					/* milliCelsius */
 					temperature = <100000>;
 					hysteresis = <2000>;
diff --git a/arch/arm/boot/dts/sun8i-a23-a33.dtsi b/arch/arm/boot/dts/allwinner/sun8i-a23-a33.dtsi
index 4461d5098b20..2af8382ccdf5 100644
--- a/arch/arm/boot/dts/sun8i-a23-a33.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-a23-a33.dtsi
@@ -44,6 +44,7 @@
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 
+#include <dt-bindings/clock/sun6i-rtc.h>
 #include <dt-bindings/clock/sun8i-a23-a33-ccu.h>
 #include <dt-bindings/reset/sun8i-a23-a33-ccu.h>
 
@@ -107,7 +108,7 @@
 		#size-cells = <1>;
 		ranges;
 
-		osc24M: osc24M_clk {
+		osc24M: osc24M-clk {
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <24000000>;
@@ -115,7 +116,7 @@
 			clock-output-names = "osc24M";
 		};
 
-		ext_osc32k: ext_osc32k_clk {
+		ext_osc32k: ext-osc32k-clk {
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <32768>;
@@ -189,7 +190,7 @@
 			clock-names = "ahb",
 				      "tcon-ch0",
 				      "lvds-alt";
-			clock-output-names = "tcon-pixel-clock";
+			clock-output-names = "tcon-data-clock";
 			#clock-cells = <0>;
 			resets = <&ccu RST_BUS_LCD>,
 				 <&ccu RST_BUS_LVDS>;
@@ -329,7 +330,7 @@
 
 		ccu: clock@1c20000 {
 			reg = <0x01c20000 0x400>;
-			clocks = <&osc24M>, <&rtc 0>;
+			clocks = <&osc24M>, <&rtc CLK_OSC32K>;
 			clock-names = "hosc", "losc";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -340,7 +341,8 @@
 			reg = <0x01c20800 0x400>;
 			interrupt-parent = <&r_intc>;
 			/* interrupts get set in SoC specific dtsi file */
-			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&rtc 0>;
+			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>,
+				 <&rtc CLK_OSC32K>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			interrupt-controller;
@@ -488,7 +490,7 @@
 			clocks = <&ccu CLK_BUS_UART0>;
 			resets = <&ccu RST_BUS_UART0>;
 			dmas = <&dma 6>, <&dma 6>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -501,7 +503,7 @@
 			clocks = <&ccu CLK_BUS_UART1>;
 			resets = <&ccu RST_BUS_UART1>;
 			dmas = <&dma 7>, <&dma 7>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -514,7 +516,7 @@
 			clocks = <&ccu CLK_BUS_UART2>;
 			resets = <&ccu RST_BUS_UART2>;
 			dmas = <&dma 8>, <&dma 8>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -527,7 +529,7 @@
 			clocks = <&ccu CLK_BUS_UART3>;
 			resets = <&ccu RST_BUS_UART3>;
 			dmas = <&dma 9>, <&dma 9>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -540,7 +542,7 @@
 			clocks = <&ccu CLK_BUS_UART4>;
 			resets = <&ccu RST_BUS_UART4>;
 			dmas = <&dma 10>, <&dma 10>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -731,7 +733,7 @@
 			compatible = "allwinner,sun8i-a23-prcm";
 			reg = <0x01f01400 0x200>;
 
-			ar100: ar100_clk {
+			ar100: ar100-clk {
 				compatible = "fixed-factor-clock";
 				#clock-cells = <0>;
 				clock-div = <1>;
@@ -740,7 +742,7 @@
 				clock-output-names = "ar100";
 			};
 
-			ahb0: ahb0_clk {
+			ahb0: ahb0-clk {
 				compatible = "fixed-factor-clock";
 				#clock-cells = <0>;
 				clock-div = <1>;
@@ -749,14 +751,14 @@
 				clock-output-names = "ahb0";
 			};
 
-			apb0: apb0_clk {
+			apb0: apb0-clk {
 				compatible = "allwinner,sun8i-a23-apb0-clk";
 				#clock-cells = <0>;
 				clocks = <&ahb0>;
 				clock-output-names = "apb0";
 			};
 
-			apb0_gates: apb0_gates_clk {
+			apb0_gates: apb0-gates-clk {
 				compatible = "allwinner,sun8i-a23-apb0-gates-clk";
 				#clock-cells = <1>;
 				clocks = <&apb0>;
@@ -765,7 +767,7 @@
 						"apb0_i2c";
 			};
 
-			apb0_rst: apb0_rst {
+			apb0_rst: apb0-rst {
 				compatible = "allwinner,sun6i-a31-clock-reset";
 				#reset-cells = <1>;
 			};
@@ -810,9 +812,8 @@
 			reg = <0x01f02c00 0x400>;
 			interrupt-parent = <&r_intc>;
 			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&apb0_gates 0>, <&osc24M>, <&rtc 0>;
+			clocks = <&apb0_gates 0>, <&osc24M>, <&rtc CLK_OSC32K>;
 			clock-names = "apb", "hosc", "losc";
-			resets = <&apb0_rst 0>;
 			gpio-controller;
 			interrupt-controller;
 			#interrupt-cells = <3>;
diff --git a/arch/arm/boot/dts/sun8i-a23-evb.dts b/arch/arm/boot/dts/allwinner/sun8i-a23-evb.dts
index 53fb1be0401a..53fb1be0401a 100644
--- a/arch/arm/boot/dts/sun8i-a23-evb.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a23-evb.dts
diff --git a/arch/arm/boot/dts/sun8i-a23-gt90h-v4.dts b/arch/arm/boot/dts/allwinner/sun8i-a23-gt90h-v4.dts
index bcbc9b0758f9..bcbc9b0758f9 100644
--- a/arch/arm/boot/dts/sun8i-a23-gt90h-v4.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a23-gt90h-v4.dts
diff --git a/arch/arm/boot/dts/sun8i-a23-inet86dz.dts b/arch/arm/boot/dts/allwinner/sun8i-a23-inet86dz.dts
index d4405752a414..d4405752a414 100644
--- a/arch/arm/boot/dts/sun8i-a23-inet86dz.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a23-inet86dz.dts
diff --git a/arch/arm/boot/dts/sun8i-a23-ippo-q8h-v1.2.dts b/arch/arm/boot/dts/allwinner/sun8i-a23-ippo-q8h-v1.2.dts
index c2f22fc33811..c2f22fc33811 120000
--- a/arch/arm/boot/dts/sun8i-a23-ippo-q8h-v1.2.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a23-ippo-q8h-v1.2.dts
diff --git a/arch/arm/boot/dts/sun8i-a23-ippo-q8h-v5.dts b/arch/arm/boot/dts/allwinner/sun8i-a23-ippo-q8h-v5.dts
index c2f22fc33811..c2f22fc33811 120000
--- a/arch/arm/boot/dts/sun8i-a23-ippo-q8h-v5.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a23-ippo-q8h-v5.dts
diff --git a/arch/arm/boot/dts/sun8i-a23-polaroid-mid2407pxe03.dts b/arch/arm/boot/dts/allwinner/sun8i-a23-polaroid-mid2407pxe03.dts
index d5f6aebd7216..0c585a6d990d 100644
--- a/arch/arm/boot/dts/sun8i-a23-polaroid-mid2407pxe03.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a23-polaroid-mid2407pxe03.dts
@@ -52,7 +52,7 @@
 		ethernet0 = &esp8089;
 	};
 
-	wifi_pwrseq: wifi_pwrseq {
+	wifi_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL6 */
 		/* The esp8089 needs 200 ms after driving wifi-en high */
@@ -76,7 +76,7 @@
 	non-removable;
 	status = "okay";
 
-	esp8089: sdio_wifi@1 {
+	esp8089: wifi@1 {
 		compatible = "esp,esp8089";
 		reg = <1>;
 		esp,crystal-26M-en = <2>;
diff --git a/arch/arm/boot/dts/sun8i-a23-polaroid-mid2809pxe04.dts b/arch/arm/boot/dts/allwinner/sun8i-a23-polaroid-mid2809pxe04.dts
index 9f9232a2fefb..63cb4e194a03 100644
--- a/arch/arm/boot/dts/sun8i-a23-polaroid-mid2809pxe04.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a23-polaroid-mid2809pxe04.dts
@@ -52,7 +52,7 @@
 		ethernet0 = &esp8089;
 	};
 
-	wifi_pwrseq: wifi_pwrseq {
+	wifi_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL6 */
 		/* The esp8089 needs 200 ms after driving wifi-en high */
@@ -69,7 +69,7 @@
 	non-removable;
 	status = "okay";
 
-	esp8089: sdio_wifi@1 {
+	esp8089: wifi@1 {
 		compatible = "esp,esp8089";
 		reg = <1>;
 		esp,crystal-26M-en = <2>;
diff --git a/arch/arm/boot/dts/sun8i-a23-q8-tablet.dts b/arch/arm/boot/dts/allwinner/sun8i-a23-q8-tablet.dts
index 51097c77a152..51097c77a152 100644
--- a/arch/arm/boot/dts/sun8i-a23-q8-tablet.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a23-q8-tablet.dts
diff --git a/arch/arm/boot/dts/sun8i-a23.dtsi b/arch/arm/boot/dts/allwinner/sun8i-a23.dtsi
index a5e884a8b2ae..a5e884a8b2ae 100644
--- a/arch/arm/boot/dts/sun8i-a23.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-a23.dtsi
diff --git a/arch/arm/boot/dts/sun8i-a33-et-q8-v1.6.dts b/arch/arm/boot/dts/allwinner/sun8i-a33-et-q8-v1.6.dts
index 4519fd791a8f..4519fd791a8f 120000
--- a/arch/arm/boot/dts/sun8i-a33-et-q8-v1.6.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a33-et-q8-v1.6.dts
diff --git a/arch/arm/boot/dts/sun8i-a33-ga10h-v1.1.dts b/arch/arm/boot/dts/allwinner/sun8i-a33-ga10h-v1.1.dts
index 2dfdd0a3151e..f00ce03ffc84 100644
--- a/arch/arm/boot/dts/sun8i-a33-ga10h-v1.1.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a33-ga10h-v1.1.dts
@@ -85,7 +85,7 @@
 	non-removable;
 	status = "okay";
 
-	rtl8703as: sdio_wifi@1 {
+	rtl8703as: wifi@1 {
 		reg = <1>;
 	};
 };
diff --git a/arch/arm/boot/dts/sun8i-a33-inet-d978-rev2.dts b/arch/arm/boot/dts/allwinner/sun8i-a33-inet-d978-rev2.dts
index 065cb620aa99..162ba93f7484 100644
--- a/arch/arm/boot/dts/sun8i-a33-inet-d978-rev2.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a33-inet-d978-rev2.dts
@@ -78,7 +78,7 @@
 	non-removable;
 	status = "okay";
 
-	rtl8723bs: sdio_wifi@1 {
+	rtl8723bs: wifi@1 {
 		reg = <1>;
 	};
 };
diff --git a/arch/arm/boot/dts/sun8i-a33-ippo-q8h-v1.2.dts b/arch/arm/boot/dts/allwinner/sun8i-a33-ippo-q8h-v1.2.dts
index 4519fd791a8f..4519fd791a8f 120000
--- a/arch/arm/boot/dts/sun8i-a33-ippo-q8h-v1.2.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a33-ippo-q8h-v1.2.dts
diff --git a/arch/arm/boot/dts/sun8i-a33-olinuxino.dts b/arch/arm/boot/dts/allwinner/sun8i-a33-olinuxino.dts
index 6fee8f133508..6fee8f133508 100644
--- a/arch/arm/boot/dts/sun8i-a33-olinuxino.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a33-olinuxino.dts
diff --git a/arch/arm/boot/dts/sun8i-a33-q8-tablet.dts b/arch/arm/boot/dts/allwinner/sun8i-a33-q8-tablet.dts
index 9c5750c25613..9c5750c25613 100644
--- a/arch/arm/boot/dts/sun8i-a33-q8-tablet.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a33-q8-tablet.dts
diff --git a/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts b/arch/arm/boot/dts/allwinner/sun8i-a33-sinlinx-sina33.dts
index 0c82ff3c7cb4..0c82ff3c7cb4 100644
--- a/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a33-sinlinx-sina33.dts
diff --git a/arch/arm/boot/dts/allwinner/sun8i-a33-vstar-core1.dtsi b/arch/arm/boot/dts/allwinner/sun8i-a33-vstar-core1.dtsi
new file mode 100644
index 000000000000..ba794b842ec4
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-a33-vstar-core1.dtsi
@@ -0,0 +1,96 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2024 Icenowy Zheng <uwu@icenowy.me>
+ */
+
+#include "sun8i-a33.dtsi"
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_pins>;
+	vmmc-supply = <&reg_dcdc1>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	status = "okay";
+};
+
+&mmc2_8bit_pins {
+	/* Increase drive strength for DDR modes */
+	drive-strength = <40>;
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp22x: pmic@3a3 {
+		compatible = "x-powers,axp223";
+		reg = <0x3a3>;
+		interrupt-parent = <&r_intc>;
+		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
+		eldoin-supply = <&reg_dcdc1>;
+		x-powers,drive-vbus-en;
+	};
+};
+
+#include "axp223.dtsi"
+
+&reg_aldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-io";
+};
+
+&reg_aldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <2350000>;
+	regulator-max-microvolt = <2650000>;
+	regulator-name = "vdd-dll";
+};
+
+&reg_aldo3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-avcc";
+};
+
+&reg_dc5ldo {
+	regulator-always-on;
+	regulator-min-microvolt = <900000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-cpus";
+};
+
+&reg_dcdc1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <900000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-sys";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <900000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc5 {
+	regulator-always-on;
+	regulator-min-microvolt = <1500000>;
+	regulator-max-microvolt = <1500000>;
+	regulator-name = "vcc-dram";
+};
+
+&reg_rtc_ldo {
+	regulator-name = "vcc-rtc";
+};
diff --git a/arch/arm/boot/dts/allwinner/sun8i-a33-vstar.dts b/arch/arm/boot/dts/allwinner/sun8i-a33-vstar.dts
new file mode 100644
index 000000000000..9f5c29b3df46
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-a33-vstar.dts
@@ -0,0 +1,205 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2024 Icenowy Zheng <uwu@icenowy.me>
+ */
+
+/dts-v1/;
+#include "sun8i-a33-vstar-core1.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Rervision A33-Vstar";
+	compatible = "rervision,a33-vstar",
+		     "rervision,a33-core1",
+		     "allwinner,sun8i-a33";
+
+	aliases {
+		serial0 = &uart0;
+		ethernet0 = &r8152;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_usb1_vbus: regulator-usb1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 */
+	};
+
+	wifi_pwrseq: pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL6 */
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
+		clock-names = "ext_clock";
+	};
+};
+
+&ac_power_supply {
+	status = "okay";
+};
+
+&codec {
+	status = "okay";
+};
+
+&dai {
+	status = "okay";
+};
+
+&ehci0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	hub@1 {
+		/* Onboard GL850G hub which needs no extra power sequence */
+		compatible = "usb5e3,608";
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		r8152: ethernet@4 {
+			/*
+			 * Onboard Realtek RTL8152 USB Ethernet,
+			 * with no MAC address programmed
+			 */
+			compatible = "usbbda,8152";
+			reg = <4>;
+		};
+	};
+};
+
+&lradc {
+	vref-supply = <&reg_aldo3>;
+	status = "okay";
+
+	button-191 {
+		label = "V+";
+		linux,code = <KEY_VOLUMEUP>;
+		channel = <0>;
+		voltage = <191011>;
+	};
+
+	button-391 {
+		label = "V-";
+		linux,code = <KEY_VOLUMEDOWN>;
+		channel = <0>;
+		voltage = <391304>;
+	};
+
+	button-600 {
+		label = "BACK";
+		linux,code = <KEY_BACK>;
+		channel = <0>;
+		voltage = <600000>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_dcdc1>;
+	bus-width = <4>;
+	cd-gpios = <&pio 1 4 GPIO_ACTIVE_LOW>; /* PB4 */
+	status = "okay";
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pg_pins>;
+	vmmc-supply = <&reg_dldo1>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&r_pio>;
+		interrupts = <0 7 IRQ_TYPE_LEVEL_LOW>; /* PL7 */
+		interrupt-names = "host-wake";
+	};
+};
+
+/*
+ * Our WiFi chip needs both DLDO1 and DLDO2 to be powered at the same
+ * time, with the two being in sync. Since this is not really
+ * supported right now, just use the two as always on, and we will fix
+ * it later.
+ */
+&reg_dldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi0";
+};
+
+&reg_dldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-wifi1";
+};
+
+&reg_drivevbus {
+	regulator-name = "usb0-vbus";
+	status = "okay";
+};
+
+&sound {
+	/* TODO: on-board microphone */
+
+	simple-audio-card,widgets = "Headphone", "Headphone Jack";
+	simple-audio-card,routing =
+		"Left DAC", "DACL",
+		"Right DAC", "DACR",
+		"Headphone Jack", "HP";
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pb_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pg_pins>, <&uart1_cts_rts_pg_pins>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
+		clock-names = "lpo";
+		vbat-supply = <&reg_dldo1>;
+		device-wakeup-gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
+		host-wakeup-gpios = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */
+		shutdown-gpios = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+	};
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb_power_supply {
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
+	usb0_vbus_power-supply = <&usb_power_supply>;
+	usb0_vbus-supply = <&reg_drivevbus>;
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sun8i-a33.dtsi b/arch/arm/boot/dts/allwinner/sun8i-a33.dtsi
index b3d1bdfb5118..36b2d78cdab9 100644
--- a/arch/arm/boot/dts/sun8i-a33.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-a33.dtsi
@@ -278,6 +278,7 @@
 		dphy: d-phy@1ca1000 {
 			compatible = "allwinner,sun6i-a31-mipi-dphy";
 			reg = <0x01ca1000 0x1000>;
+			interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_MIPI_DSI>,
 				 <&ccu CLK_DSI_DPHY>;
 			clock-names = "bus", "mod";
@@ -322,35 +323,35 @@
 			};
 
 			trips {
-				cpu_alert0: cpu_alert0 {
+				cpu_alert0: cpu-alert0 {
 					/* milliCelsius */
 					temperature = <75000>;
 					hysteresis = <2000>;
 					type = "passive";
 				};
 
-				gpu_alert0: gpu_alert0 {
+				gpu_alert0: gpu-alert0 {
 					/* milliCelsius */
 					temperature = <85000>;
 					hysteresis = <2000>;
 					type = "passive";
 				};
 
-				cpu_alert1: cpu_alert1 {
+				cpu_alert1: cpu-alert1 {
 					/* milliCelsius */
 					temperature = <90000>;
 					hysteresis = <2000>;
 					type = "hot";
 				};
 
-				gpu_alert1: gpu_alert1 {
+				gpu_alert1: gpu-alert1 {
 					/* milliCelsius */
 					temperature = <95000>;
 					hysteresis = <2000>;
 					type = "hot";
 				};
 
-				cpu_crit: cpu_crit {
+				cpu_crit: cpu-crit {
 					/* milliCelsius */
 					temperature = <110000>;
 					hysteresis = <2000>;
diff --git a/arch/arm/boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts b/arch/arm/boot/dts/allwinner/sun8i-a83t-allwinner-h8homlet-v2.dts
index c31c97d16024..c31c97d16024 100644
--- a/arch/arm/boot/dts/sun8i-a83t-allwinner-h8homlet-v2.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a83t-allwinner-h8homlet-v2.dts
diff --git a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts b/arch/arm/boot/dts/allwinner/sun8i-a83t-bananapi-m3.dts
index 5a7e1bd5f825..32e811fa23e2 100644
--- a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a83t-bananapi-m3.dts
@@ -95,7 +95,7 @@
 		gpio = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
 	};
 
-	wifi_pwrseq: wifi_pwrseq {
+	wifi_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		clocks = <&ac100_rtc 1>;
 		clock-names = "ext_clock";
@@ -105,6 +105,21 @@
 		/* enables internal regulator and de-asserts reset */
 		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
 	};
+
+	/*
+	 * Power supply for the SATA disk, behind a USB-SATA bridge.
+	 * Since it is a USB device, there is no consumer in the DT, so we
+	 * have to keep this always on.
+	 */
+	regulator-sata-disk-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "sata-disk-pwr";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		enable-active-high;
+		gpio = <&pio 3 25 GPIO_ACTIVE_HIGH>; /* PD25 */
+	};
 };
 
 &cpu0 {
diff --git a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts b/arch/arm/boot/dts/allwinner/sun8i-a83t-cubietruck-plus.dts
index 870993393fc2..d5e6ddaffbce 100644
--- a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a83t-cubietruck-plus.dts
@@ -144,7 +144,7 @@
 		compatible = "linux,spdif-dit";
 	};
 
-	wifi_pwrseq: wifi_pwrseq {
+	wifi_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		clocks = <&ac100_rtc 1>;
 		clock-names = "ext_clock";
diff --git a/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts b/arch/arm/boot/dts/allwinner/sun8i-a83t-tbs-a711.dts
index a7d4ca308990..43982b106a4d 100644
--- a/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-a83t-tbs-a711.dts
@@ -123,7 +123,7 @@
 		vin-supply = <&reg_vbat>;
 	};
 
-	wifi_pwrseq: wifi_pwrseq {
+	wifi_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
 
diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/allwinner/sun8i-a83t.dtsi
index 82fdb04122ca..6f88d8764e6a 100644
--- a/arch/arm/boot/dts/sun8i-a83t.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-a83t.dtsi
@@ -164,7 +164,7 @@
 		ranges;
 
 		/* TODO: PRCM block has a mux for this. */
-		osc24M: osc24M_clk {
+		osc24M: osc24M-clk {
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <24000000>;
@@ -177,14 +177,14 @@
 		 * It is an internal RC-based oscillator.
 		 * TODO: Its controls are in the PRCM block.
 		 */
-		osc16M: osc16M_clk {
+		osc16M: osc16M-clk {
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <16000000>;
 			clock-output-names = "osc16M";
 		};
 
-		osc16Md512: osc16Md512_clk {
+		osc16Md512: osc16Md512-clk {
 			#clock-cells = <0>;
 			compatible = "fixed-factor-clock";
 			clock-div = <512>;
@@ -456,7 +456,7 @@
 			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_TCON0>, <&ccu CLK_TCON0>;
 			clock-names = "ahb", "tcon-ch0";
-			clock-output-names = "tcon-pixel-clock";
+			clock-output-names = "tcon-data-clock";
 			#clock-cells = <0>;
 			resets = <&ccu RST_BUS_TCON0>, <&ccu RST_BUS_LVDS>;
 			reset-names = "lcd", "lvds";
@@ -1127,7 +1127,7 @@
 			#reset-cells = <1>;
 		};
 
-		r_cpucfg@1f01c00 {
+		cpucfg@1f01c00 {
 			compatible = "allwinner,sun8i-a83t-r-cpucfg";
 			reg = <0x1f01c00 0x400>;
 		};
@@ -1225,7 +1225,7 @@
 			};
 
 			cooling-maps {
-				cpu-hot-limit {
+				map0 {
 					trip = <&cpu0_hot>;
 					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
 							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
@@ -1255,7 +1255,7 @@
 			};
 
 			cooling-maps {
-				cpu-hot-limit {
+				map0 {
 					trip = <&cpu1_hot>;
 					cooling-device = <&cpu100 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
 							 <&cpu101 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-bananapi-m2-zero.dts
index d5c7b7984d85..d3a7c9fa23e4 100644
--- a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-bananapi-m2-zero.dts
@@ -47,10 +47,10 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		sw4 {
+		switch-4 {
 			label = "power";
 			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
@@ -103,10 +103,10 @@
 		cpu-supply = <&reg_vcc1v2>;
 	};
 
-	wifi_pwrseq: wifi_pwrseq {
+	wifi_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "ext_clock";
 	};
 };
@@ -181,7 +181,7 @@
 	bluetooth {
 		compatible = "brcm,bcm43438-bt";
 		max-speed = <1500000>;
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "lpo";
 		vbat-supply = <&reg_vcc3v3>;
 		vddio-supply = <&reg_vcc3v3>;
diff --git a/arch/arm/boot/dts/sun8i-h2-plus-libretech-all-h3-cc.dts b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-libretech-all-h3-cc.dts
index 4db0d4bb65eb..4db0d4bb65eb 100644
--- a/arch/arm/boot/dts/sun8i-h2-plus-libretech-all-h3-cc.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-libretech-all-h3-cc.dts
diff --git a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-r1.dts b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-r1.dts
index 3356f4210d45..79b03b31c5eb 100644
--- a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-r1.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-r1.dts
@@ -43,11 +43,12 @@
 /* Orange Pi R1 is based on Orange Pi Zero design */
 #include "sun8i-h2-plus-orangepi-zero.dts"
 
+/delete-node/ &reg_vcc_wifi;
+
 / {
 	model = "Xunlong Orange Pi R1";
 	compatible = "xunlong,orangepi-r1", "allwinner,sun8i-h2-plus";
 
-	/delete-node/ reg_vcc_wifi;
 
 	/*
 	 * Ths pin of this regulator is the same with the Wi-Fi extra
@@ -89,7 +90,7 @@
 	vmmc-supply = <&reg_vcc3v3>;
 	vqmmc-supply = <&reg_vcc3v3>;
 
-	rtl8189etv: sdio_wifi@1 {
+	rtl8189etv: wifi@1 {
 		reg = <1>;
 	};
 };
diff --git a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
index f19ed981da9d..b23cec5b89eb 100644
--- a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
@@ -80,7 +80,7 @@
 		};
 	};
 
-	reg_vcc_wifi: reg_vcc_wifi {
+	reg_vcc_wifi: reg-vcc-wifi {
 		compatible = "regulator-fixed";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
@@ -105,13 +105,27 @@
 		states = <1100000 0>, <1300000 1>;
 	};
 
-	wifi_pwrseq: wifi_pwrseq {
+	wifi_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>;
 		post-power-on-delay-ms = <200>;
 	};
 };
 
+/*
+ * Audio input/output is exposed on the 13-pin header and can't be used for
+ * anything else. However, adapter boards may use different audio routing.
+ * - https://linux-sunxi.org/Xunlong_Orange_Pi_Zero#Expansion_Port
+ * - Allwinner H3 Datasheet, section 3.1. Pin Characteristics
+ */
+&codec {
+	allwinner,audio-routing =
+		"Line Out", "LINEOUT",
+		"MIC1", "Mic",
+		"Mic",  "MBIAS";
+	status = "disabled";
+};
+
 &cpu0 {
 	cpu-supply = <&reg_vdd_cpux>;
 };
@@ -149,7 +163,7 @@
 	 * Explicitly define the sdio device, so that we can add an ethernet
 	 * alias for it (which e.g. makes u-boot set a mac-address).
 	 */
-	xr819: sdio_wifi@1 {
+	xr819: wifi@1 {
 		reg = <1>;
 	};
 };
@@ -169,7 +183,7 @@
 	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "mxicy,mx25l1606e", "winbond,w25q128";
+		compatible = "mxicy,mx25l1606e", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <40000000>;
 	};
diff --git a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus-v1.2.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-bananapi-m2-plus-v1.2.dts
index fc4a8c3d084d..fc4a8c3d084d 100644
--- a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus-v1.2.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-bananapi-m2-plus-v1.2.dts
diff --git a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-bananapi-m2-plus.dts
index 195a75da13f1..195a75da13f1 100644
--- a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-bananapi-m2-plus.dts
diff --git a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-beelink-x2.dts
index cd9f655e4f92..5b77300307de 100644
--- a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-beelink-x2.dts
@@ -57,7 +57,7 @@
 		ethernet1 = &sdiowifi;
 	};
 
-	cec-gpio {
+	cec {
 		compatible = "cec-gpio";
 		cec-gpios = <&pio 0 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; /* PA14 */
 		hdmi-phandle = <&hdmi>;
@@ -93,10 +93,10 @@
 		};
 	};
 
-	r-gpio-keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "power";
 			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
@@ -122,10 +122,10 @@
 		compatible = "linux,spdif-dit";
 	};
 
-	wifi_pwrseq: wifi_pwrseq {
+	wifi_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "ext_clock";
 	};
 };
@@ -185,7 +185,7 @@
 	 * Explicitly define the sdio device, so that we can add an ethernet
 	 * alias for it (which e.g. makes u-boot set a mac-address).
 	 */
-	sdiowifi: sdio_wifi@1 {
+	sdiowifi: wifi@1 {
 		reg = <1>;
 	};
 };
diff --git a/arch/arm/boot/dts/sun8i-h3-emlid-neutis-n5h3-devboard.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-emlid-neutis-n5h3-devboard.dts
index 02fbe00cde97..02fbe00cde97 100644
--- a/arch/arm/boot/dts/sun8i-h3-emlid-neutis-n5h3-devboard.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-emlid-neutis-n5h3-devboard.dts
diff --git a/arch/arm/boot/dts/sun8i-h3-emlid-neutis-n5h3.dtsi b/arch/arm/boot/dts/allwinner/sun8i-h3-emlid-neutis-n5h3.dtsi
index eedd5da5dc2f..35e71f46c197 100644
--- a/arch/arm/boot/dts/sun8i-h3-emlid-neutis-n5h3.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-emlid-neutis-n5h3.dtsi
@@ -8,4 +8,4 @@
 /dts-v1/;
 
 #include "sun8i-h3.dtsi"
-#include <arm/sunxi-h3-h5-emlid-neutis.dtsi>
+#include "sunxi-h3-h5-emlid-neutis.dtsi"
diff --git a/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-libretech-all-h3-cc.dts
index a8b2f0f1c11d..a8b2f0f1c11d 100644
--- a/arch/arm/boot/dts/sun8i-h3-libretech-all-h3-cc.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-libretech-all-h3-cc.dts
diff --git a/arch/arm/boot/dts/sun8i-h3-mapleboard-mp130.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-mapleboard-mp130.dts
index ff0a7a952e0c..f5c8ccc5b872 100644
--- a/arch/arm/boot/dts/sun8i-h3-mapleboard-mp130.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-mapleboard-mp130.dts
@@ -39,16 +39,16 @@
 		};
 	};
 
-	r_gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "power";
 			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; /* PL3 */
 		};
 
-		user {
+		key-user {
 			label = "user";
 			linux,code = <BTN_0>;
 			gpios = <&r_pio 0 4 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-duo2.dts
index 8e7dfcffe1fb..2b0566d4b386 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-duo2.dts
@@ -37,10 +37,10 @@
 		};
 	};
 
-	r_gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		k1 {
+		key-0 {
 			label = "k1";
 			linux,code = <BTN_0>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; /* PL3 */
@@ -57,7 +57,7 @@
 		regulator-ramp-delay = <50>; /* 4ms */
 
 		enable-active-high;
-		enable-gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
+		enable-gpios = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */
 		gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
 		gpios-states = <0x1>;
 		states = <1100000 0>, <1300000 1>;
@@ -87,10 +87,10 @@
 		vin-supply = <&reg_vcc5v0>;
         };
 
-	wifi_pwrseq: wifi_pwrseq {
+	wifi_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "ext_clock";
 	};
 
@@ -119,7 +119,7 @@
 	non-removable;
 	status = "okay";
 
-	sdio_wifi: sdio_wifi@1 {
+	sdio_wifi: wifi@1 {
 		reg = <1>;
 		compatible = "brcm,bcm4329-fmac";
 		interrupt-parent = <&pio>;
@@ -151,7 +151,7 @@
 
 	bluetooth {
 		compatible = "brcm,bcm43438-bt";
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "lpo";
 		vbat-supply = <&reg_vcc3v3>;
 		vddio-supply = <&reg_vcc3v3>;
diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-m1-plus.dts
index 4ba533b0340f..59bd0746acf8 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-m1-plus.dts
@@ -62,7 +62,7 @@
 		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
 	};
 
-	wifi_pwrseq: wifi_pwrseq {
+	wifi_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
 	};
@@ -132,7 +132,7 @@
 	non-removable;
 	status = "okay";
 
-	sdio_wifi: sdio_wifi@1 {
+	sdio_wifi: wifi@1 {
 		reg = <1>;
 		compatible = "brcm,bcm4329-fmac";
 		interrupt-parent = <&pio>;
diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-m1.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-m1.dts
index 69243dcb30a6..69243dcb30a6 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-m1.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-m1.dts
diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-neo-air.dts
index cd3df12b6573..9a2742363cd0 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-neo-air.dts
@@ -73,7 +73,7 @@
 		};
 	};
 
-	wifi_pwrseq: wifi_pwrseq {
+	wifi_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
 	};
@@ -94,7 +94,7 @@
 	non-removable;
 	status = "okay";
 
-	brcmf: bcrmf@1 {
+	brcmf: wifi@1 {
 		reg = <1>;
 		compatible = "brcm,bcm4329-fmac";
 		interrupt-parent = <&pio>;
@@ -127,7 +127,7 @@
 
 	bluetooth {
 		compatible = "brcm,bcm43438-bt";
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "lpo";
 		vbat-supply = <&reg_vcc3v3>;
 		vddio-supply = <&reg_vcc3v3>;
diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-neo.dts
index df71fab3cf4e..df71fab3cf4e 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-neo.dts
diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-r1.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-r1.dts
index 26e2e6172e0d..870649760f70 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-r1.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi-r1.dts
@@ -43,10 +43,10 @@
 			 <1300000 0x1>;
 	};
 
-	wifi_pwrseq: wifi_pwrseq {
+	wifi_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "ext_clock";
 	};
 
@@ -147,7 +147,7 @@
 
 	bluetooth {
 		compatible = "brcm,bcm43438-bt";
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "lpo";
 		vbat-supply = <&reg_vcc3v3>;
 		vddio-supply = <&reg_vcc3v3>;
diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi.dtsi
index fc45d5aaa67f..cf8413fba6c1 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-nanopi.dtsi
@@ -73,11 +73,10 @@
 		};
 	};
 
-	r_gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		input-name = "k1";
 
-		k1 {
+		key-0 {
 			label = "k1";
 			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-2.dts
index 9daffd90c12f..d2ae47b074bf 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-2.dts
@@ -88,16 +88,16 @@
 		};
 	};
 
-	r_gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		sw2 {
+		switch-2 {
 			label = "sw2";
 			linux,code = <BTN_1>;
 			gpios = <&r_pio 0 4 GPIO_ACTIVE_LOW>;
 		};
 
-		sw4 {
+		switch-4 {
 			label = "sw4";
 			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
@@ -105,7 +105,7 @@
 		};
 	};
 
-	wifi_pwrseq: wifi_pwrseq {
+	wifi_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 WIFI_EN */
 	};
@@ -169,7 +169,7 @@
 	 * Explicitly define the sdio device, so that we can add an ethernet
 	 * alias for it (which e.g. makes u-boot set a mac-address).
 	 */
-	rtl8189: sdio_wifi@1 {
+	rtl8189: wifi@1 {
 		reg = <1>;
 	};
 };
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-lite.dts
index 6f9c97add54e..6a4316a52469 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-lite.dts
@@ -87,10 +87,10 @@
 		};
 	};
 
-	r_gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		sw4 {
+		switch-4 {
 			label = "sw4";
 			linux,code = <BTN_0>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
@@ -143,7 +143,7 @@
 	 * Explicitly define the sdio device, so that we can add an ethernet
 	 * alias for it (which e.g. makes u-boot set a mac-address).
 	 */
-	rtl8189ftv: sdio_wifi@1 {
+	rtl8189ftv: wifi@1 {
 		reg = <1>;
 	};
 };
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-one.dts
index 4759ba3f2986..59f6f6d5e7ca 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-one.dts
@@ -86,10 +86,10 @@
 		};
 	};
 
-	r_gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		sw4 {
+		switch-4 {
 			label = "sw4";
 			linux,code = <BTN_0>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-pc-plus.dts
index babf4cf1b2f6..8a49b3376dfc 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc-plus.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-pc-plus.dts
@@ -63,7 +63,7 @@
 	 * Explicitly define the sdio device, so that we can add an ethernet
 	 * alias for it (which e.g. makes u-boot set a mac-address).
 	 */
-	rtl8189ftv: sdio_wifi@1 {
+	rtl8189ftv: wifi@1 {
 		reg = <1>;
 	};
 };
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-pc.dts
index 90f75fa85e68..b96e015f54ee 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-pc.dts
@@ -86,10 +86,10 @@
 		};
 	};
 
-	r_gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		sw4 {
+		switch-4 {
 			label = "sw4";
 			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-plus.dts
index d05fa679dcd3..d05fa679dcd3 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-plus.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-plus.dts
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-plus2e.dts
index b6ca45d18e51..b6ca45d18e51 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-plus2e.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-plus2e.dts
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-zero-plus2.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-zero-plus2.dts
index 561ea1d2f861..97a3565ac7a8 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-zero-plus2.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-zero-plus2.dts
@@ -92,13 +92,27 @@
 		regulator-max-microvolt = <3300000>;
 	};
 
-	wifi_pwrseq: wifi_pwrseq {
+	wifi_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */
 		post-power-on-delay-ms = <200>;
 	};
 };
 
+/*
+ * Audio input/output is exposed on the 13-pin header and can't be used for
+ * anything else. However, adapter boards may use different audio routing.
+ * - http://www.orangepi.org/html/hardWare/computerAndMicrocontrollers/details/Orange-Pi-Zero-Plus-2.html
+ * - Allwinner H3 Datasheet, section 3.1. Pin Characteristics
+ */
+&codec {
+	allwinner,audio-routing =
+		"Line Out", "LINEOUT",
+		"MIC1", "Mic",
+		"Mic",  "MBIAS";
+	status = "disabled";
+};
+
 &de {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/sun8i-h3-rervision-dvk.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-rervision-dvk.dts
index 4738f3a9efe4..4738f3a9efe4 100644
--- a/arch/arm/boot/dts/sun8i-h3-rervision-dvk.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-rervision-dvk.dts
diff --git a/arch/arm/boot/dts/sun8i-h3-zeropi.dts b/arch/arm/boot/dts/allwinner/sun8i-h3-zeropi.dts
index 7d3e7323b661..7d3e7323b661 100644
--- a/arch/arm/boot/dts/sun8i-h3-zeropi.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3-zeropi.dts
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/allwinner/sun8i-h3.dtsi
index eac2349a2380..cfd039840b43 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-h3.dtsi
@@ -262,7 +262,7 @@
 			};
 
 			cooling-maps {
-				cpu-hot-limit {
+				map0 {
 					trip = <&cpu_hot_trip>;
 					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
 							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
diff --git a/arch/arm/boot/dts/allwinner/sun8i-orangepi-zero-interface-board.dtso b/arch/arm/boot/dts/allwinner/sun8i-orangepi-zero-interface-board.dtso
new file mode 100644
index 000000000000..e137eefee341
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-orangepi-zero-interface-board.dtso
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR X11)
+/*
+ * Copyright (C) 2025 J. Neuschäfer <j.ne@posteo.net>
+ *
+ * Devicetree overlay for the Orange Pi Zero Interface board (OP0014).
+ *
+ *   https://orangepi.com/index.php?route=product/product&product_id=871
+ *
+ * This overlay applies to the following base files:
+ *
+ * - arch/arm/boot/dts/allwinner/sun8i-h2-plus-orangepi-zero.dts
+ * - arch/arm/boot/dts/allwinner/sun8i-h3-orangepi-zero-plus2.dts
+ */
+
+/dts-v1/;
+/plugin/;
+
+&codec {
+	status = "okay";
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&ehci3 {
+	status = "okay";
+};
+
+&ir {
+	pinctrl-names = "default";
+	pinctrl-0 = <&r_ir_rx_pin>;
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&ohci3 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sun8i-q8-common.dtsi b/arch/arm/boot/dts/allwinner/sun8i-q8-common.dtsi
index 3d9a1524e17e..a0f787581dd9 100644
--- a/arch/arm/boot/dts/sun8i-q8-common.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-q8-common.dtsi
@@ -62,7 +62,7 @@
 		};
 	};
 
-	wifi_pwrseq: wifi_pwrseq {
+	wifi_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		/*
 		 * Q8 boards use various PL# pins as wifi-en. On other boards
@@ -82,7 +82,7 @@
 };
 
 &ehci0 {
-	status  = "okay";
+	status = "okay";
 };
 
 &mmc1 {
@@ -94,7 +94,7 @@
 	non-removable;
 	status = "okay";
 
-	sdio_wifi: sdio_wifi@1 {
+	sdio_wifi: wifi@1 {
 		reg = <1>;
 	};
 };
diff --git a/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts b/arch/arm/boot/dts/allwinner/sun8i-r16-bananapi-m2m.dts
index bf5b5e2f6168..f4bf46b35bec 100644
--- a/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-r16-bananapi-m2m.dts
@@ -88,10 +88,10 @@
 		regulator-max-microvolt = <5000000>;
 	};
 
-	wifi_pwrseq: wifi_pwrseq {
+	wifi_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL06 */
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "ext_clock";
 	};
 };
@@ -283,7 +283,7 @@
 
 	bluetooth {
 		compatible = "brcm,bcm43438-bt";
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "lpo";
 		vbat-supply = <&reg_dldo1>;
 		vddio-supply = <&reg_aldo3>;
diff --git a/arch/arm/boot/dts/sun8i-r16-nintendo-nes-classic.dts b/arch/arm/boot/dts/allwinner/sun8i-r16-nintendo-nes-classic.dts
index 246dec5846a4..246dec5846a4 100644
--- a/arch/arm/boot/dts/sun8i-r16-nintendo-nes-classic.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-r16-nintendo-nes-classic.dts
diff --git a/arch/arm/boot/dts/sun8i-r16-nintendo-super-nes-classic.dts b/arch/arm/boot/dts/allwinner/sun8i-r16-nintendo-super-nes-classic.dts
index 80761d7904ec..80761d7904ec 100644
--- a/arch/arm/boot/dts/sun8i-r16-nintendo-super-nes-classic.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-r16-nintendo-super-nes-classic.dts
diff --git a/arch/arm/boot/dts/sun8i-r16-parrot.dts b/arch/arm/boot/dts/allwinner/sun8i-r16-parrot.dts
index 95543a9c2118..75067522ff59 100644
--- a/arch/arm/boot/dts/sun8i-r16-parrot.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-r16-parrot.dts
@@ -75,7 +75,7 @@
 		};
 	};
 
-	wifi_pwrseq: wifi_pwrseq {
+	wifi_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL06 */
 	};
diff --git a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts b/arch/arm/boot/dts/allwinner/sun8i-r40-bananapi-m2-ultra.dts
index a6a1087a0c9b..cd2351acc32f 100644
--- a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-r40-bananapi-m2-ultra.dts
@@ -43,6 +43,7 @@
 
 /dts-v1/;
 #include "sun8i-r40.dtsi"
+#include "sun8i-r40-cpu-opp.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
 
@@ -99,7 +100,7 @@
 		enable-active-high;
 	};
 
-	wifi_pwrseq: wifi_pwrseq {
+	wifi_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 WIFI_EN */
 		clocks = <&ccu CLK_OUTA>;
@@ -113,6 +114,10 @@
 	status = "okay";
 };
 
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
 &de {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/allwinner/sun8i-r40-cpu-opp.dtsi b/arch/arm/boot/dts/allwinner/sun8i-r40-cpu-opp.dtsi
new file mode 100644
index 000000000000..649928b361af
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-r40-cpu-opp.dtsi
@@ -0,0 +1,52 @@
+/{
+	cpu0_opp_table: opp-table-cpu {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-720000000 {
+			opp-hz = /bits/ 64 <720000000>;
+			opp-microvolt = <1000000 1000000 1300000>;
+			clock-latency-ns = <2000000>;
+		};
+
+		opp-912000000 {
+			opp-hz = /bits/ 64 <912000000>;
+			opp-microvolt = <1100000 1100000 1300000>;
+			clock-latency-ns = <2000000>;
+		};
+
+		opp-1008000000 {
+			opp-hz = /bits/ 64 <1008000000>;
+			opp-microvolt = <1160000 1160000 1300000>;
+			clock-latency-ns = <2000000>;
+		};
+
+		opp-1104000000 {
+			opp-hz = /bits/ 64 <1104000000>;
+			opp-microvolt = <1240000 1240000 1300000>;
+			clock-latency-ns = <2000000>;
+		};
+
+		opp-1200000000 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-microvolt = <1300000 1300000 1300000>;
+			clock-latency-ns = <2000000>;
+		};
+	};
+};
+
+&cpu0 {
+	operating-points-v2 = <&cpu0_opp_table>;
+};
+
+&cpu1 {
+	operating-points-v2 = <&cpu0_opp_table>;
+};
+
+&cpu2 {
+	operating-points-v2 = <&cpu0_opp_table>;
+};
+
+&cpu3 {
+	operating-points-v2 = <&cpu0_opp_table>;
+};
diff --git a/arch/arm/boot/dts/sun8i-r40-feta40i.dtsi b/arch/arm/boot/dts/allwinner/sun8i-r40-feta40i.dtsi
index 265e0fa57a32..c12361d0317f 100644
--- a/arch/arm/boot/dts/sun8i-r40-feta40i.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-r40-feta40i.dtsi
@@ -5,6 +5,11 @@
 //  Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
 
 #include "sun8i-r40.dtsi"
+#include "sun8i-r40-cpu-opp.dtsi"
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
 
 &i2c0 {
 	status = "okay";
@@ -37,6 +42,13 @@
 	vcc-pg-supply = <&reg_dldo1>;
 };
 
+&reg_aldo1 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3-tv-usb";
+};
+
 &reg_aldo2 {
 	regulator-always-on;
 	regulator-min-microvolt = <1800000>;
diff --git a/arch/arm/boot/dts/sun8i-r40-oka40i-c.dts b/arch/arm/boot/dts/allwinner/sun8i-r40-oka40i-c.dts
index 0bd1336206b8..15b0b4de626a 100644
--- a/arch/arm/boot/dts/sun8i-r40-oka40i-c.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-r40-oka40i-c.dts
@@ -62,7 +62,7 @@
 		regulator-max-microvolt = <5000000>;
 	};
 
-	wifi_pwrseq: wifi_pwrseq {
+	wifi_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&pio 1 10 GPIO_ACTIVE_LOW>; // PB10 WIFI_EN
 		clocks = <&ccu CLK_OUTA>;
diff --git a/arch/arm/boot/dts/sun8i-r40.dtsi b/arch/arm/boot/dts/allwinner/sun8i-r40.dtsi
index 03d3e5f45a09..f0ed802a9d08 100644
--- a/arch/arm/boot/dts/sun8i-r40.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-r40.dtsi
@@ -42,6 +42,7 @@
  */
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/sun6i-rtc.h>
 #include <dt-bindings/clock/sun8i-de2.h>
 #include <dt-bindings/clock/sun8i-r40-ccu.h>
 #include <dt-bindings/clock/sun8i-tcon-top.h>
@@ -84,24 +85,36 @@
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <0>;
+			clocks = <&ccu CLK_CPU>;
+			clock-names = "cpu";
+			#cooling-cells = <2>;
 		};
 
 		cpu1: cpu@1 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <1>;
+			clocks = <&ccu CLK_CPU>;
+			clock-names = "cpu";
+			#cooling-cells = <2>;
 		};
 
 		cpu2: cpu@2 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <2>;
+			clocks = <&ccu CLK_CPU>;
+			clock-names = "cpu";
+			#cooling-cells = <2>;
 		};
 
 		cpu3: cpu@3 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <3>;
+			clocks = <&ccu CLK_CPU>;
+			clock-names = "cpu";
+			#cooling-cells = <2>;
 		};
 	};
 
@@ -117,6 +130,30 @@
 			polling-delay-passive = <0>;
 			polling-delay = <0>;
 			thermal-sensors = <&ths 0>;
+
+			trips {
+				cpu_hot_trip: cpu-hot {
+					temperature = <80000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_very_hot_trip: cpu-very-hot {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_hot_trip>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
 		};
 
 		gpu_thermal: gpu-thermal {
@@ -301,6 +338,8 @@
 			resets = <&ccu RST_BUS_VE>;
 			interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
 			allwinner,sram = <&ve_sram 1>;
+			interconnects = <&mbus 4>;
+			interconnect-names = "dma-mem";
 		};
 
 		mmc0: mmc@1c0f000 {
@@ -485,7 +524,7 @@
 		ccu: clock@1c20000 {
 			compatible = "allwinner,sun8i-r40-ccu";
 			reg = <0x01c20000 0x400>;
-			clocks = <&osc24M>, <&rtc 0>;
+			clocks = <&osc24M>, <&rtc CLK_OSC32K>;
 			clock-names = "hosc", "losc";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -504,7 +543,8 @@
 			compatible = "allwinner,sun8i-r40-pinctrl";
 			reg = <0x01c20800 0x400>;
 			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&rtc 0>;
+			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>,
+				 <&rtc CLK_OSC32K>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			interrupt-controller;
@@ -665,7 +705,7 @@
 			};
 
 			/omit-if-no-ref/
-			uart2_rts_cts_pi_pins: uart2-rts-cts-pi-pins{
+			uart2_rts_cts_pi_pins: uart2-rts-cts-pi-pins {
 				pins = "PI16", "PI17";
 				function = "uart2";
 			};
@@ -1231,7 +1271,7 @@
 			reg-io-width = <1>;
 			interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_HDMI0>, <&ccu CLK_HDMI_SLOW>,
-				 <&ccu CLK_HDMI>, <&rtc 0>;
+				 <&ccu CLK_HDMI>, <&rtc CLK_OSC32K>;
 			clock-names = "iahb", "isfr", "tmds", "cec";
 			resets = <&ccu RST_BUS_HDMI1>;
 			reset-names = "ctrl";
diff --git a/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi b/arch/arm/boot/dts/allwinner/sun8i-reference-design-tablet.dtsi
index 872d56caa9ce..872d56caa9ce 100644
--- a/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-reference-design-tablet.dtsi
diff --git a/arch/arm/boot/dts/sun8i-s3-elimo-impetus.dtsi b/arch/arm/boot/dts/allwinner/sun8i-s3-elimo-impetus.dtsi
index 052b010a5607..052b010a5607 100644
--- a/arch/arm/boot/dts/sun8i-s3-elimo-impetus.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-s3-elimo-impetus.dtsi
diff --git a/arch/arm/boot/dts/sun8i-s3-elimo-initium.dts b/arch/arm/boot/dts/allwinner/sun8i-s3-elimo-initium.dts
index 039677c2cc65..039677c2cc65 100644
--- a/arch/arm/boot/dts/sun8i-s3-elimo-initium.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-s3-elimo-initium.dts
diff --git a/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dts b/arch/arm/boot/dts/allwinner/sun8i-s3-lichee-zero-plus.dts
index d18192d51d1b..d18192d51d1b 100644
--- a/arch/arm/boot/dts/sun8i-s3-lichee-zero-plus.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-s3-lichee-zero-plus.dts
diff --git a/arch/arm/boot/dts/sun8i-s3-pinecube.dts b/arch/arm/boot/dts/allwinner/sun8i-s3-pinecube.dts
index 20966e954eda..e0d4404b5957 100644
--- a/arch/arm/boot/dts/sun8i-s3-pinecube.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-s3-pinecube.dts
@@ -51,7 +51,7 @@
 		startup-delay-us = <200000>;
 	};
 
-	wifi_pwrseq: wifi_pwrseq {
+	wifi_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&pio 1 3 GPIO_ACTIVE_LOW>; /* PB3 WIFI-RST */
 		post-power-on-delay-ms = <200>;
diff --git a/arch/arm/boot/dts/allwinner/sun8i-t113s-mangopi-mq-r-t113.dts b/arch/arm/boot/dts/allwinner/sun8i-t113s-mangopi-mq-r-t113.dts
new file mode 100644
index 000000000000..8b3a75383816
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-t113s-mangopi-mq-r-t113.dts
@@ -0,0 +1,35 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2022 Arm Ltd.
+
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/dts-v1/;
+
+#include "sun8i-t113s.dtsi"
+#include "sunxi-d1s-t113-mangopi-mq-r.dtsi"
+
+/ {
+	model = "MangoPi MQ-R-T113";
+	compatible = "widora,mangopi-mq-r-t113", "allwinner,sun8i-t113s";
+
+	aliases {
+		ethernet0 = &rtl8189ftv;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vcc_core>;
+};
+
+&cpu1 {
+	cpu-supply = <&reg_vcc_core>;
+};
+
+&mmc1 {
+	rtl8189ftv: wifi@1 {
+		reg = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 = WL_WAKE_AP */
+		interrupt-names = "host-wake";
+	};
+};
diff --git a/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami-basic-carrier.dts b/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami-basic-carrier.dts
new file mode 100644
index 000000000000..5262102a85f6
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami-basic-carrier.dts
@@ -0,0 +1,67 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2025 Lukas Schmid <lukas.schmid@netcube.li>
+ */
+
+/dts-v1/;
+#include "sun8i-t113s-netcube-nagami.dtsi"
+
+/ {
+	model = "NetCube Systems Nagami Basic Carrier Board";
+	compatible = "netcube,nagami-basic-carrier", "netcube,nagami",
+		     "allwinner,sun8i-t113s";
+};
+
+&can0 {
+	status = "okay";
+};
+
+&can1 {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2s1 {
+	status = "okay";
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	broken-cd;
+	disable-wp;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&spi1 {
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami-keypad-carrier.dts b/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami-keypad-carrier.dts
new file mode 100644
index 000000000000..4ffa6a0216d8
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami-keypad-carrier.dts
@@ -0,0 +1,129 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2025 Lukas Schmid <lukas.schmid@netcube.li>
+ */
+
+/dts-v1/;
+#include "sun8i-t113s-netcube-nagami.dtsi"
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "NetCube Systems Nagami Keypad Carrier Board";
+	compatible = "netcube,nagami-keypad-carrier", "netcube,nagami",
+		     "allwinner,sun8i-t113s";
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_status_red: led-status-red {
+			gpios = <&pio 3 16 GPIO_ACTIVE_HIGH>;  /* PD16 */
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_STATUS;
+		};
+
+		led_status_green: led-status-green {
+			gpios = <&pio 3 22 GPIO_ACTIVE_HIGH>;  /* PD22 */
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+		};
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	tca8418: keypad@34 {
+		compatible = "ti,tca8418";
+		reg = <0x34>;
+		interrupts-extended = <&pio 5 6 IRQ_TYPE_EDGE_FALLING>;  /* PF6 */
+		linux,keymap = <MATRIX_KEY(0x03, 0x00, KEY_NUMERIC_A)
+				MATRIX_KEY(0x03, 0x01, KEY_NUMERIC_1)
+				MATRIX_KEY(0x03, 0x02, KEY_NUMERIC_2)
+				MATRIX_KEY(0x03, 0x03, KEY_NUMERIC_3)
+				MATRIX_KEY(0x02, 0x00, KEY_NUMERIC_B)
+				MATRIX_KEY(0x02, 0x01, KEY_NUMERIC_4)
+				MATRIX_KEY(0x02, 0x02, KEY_NUMERIC_5)
+				MATRIX_KEY(0x02, 0x03, KEY_NUMERIC_6)
+				MATRIX_KEY(0x01, 0x00, KEY_NUMERIC_C)
+				MATRIX_KEY(0x01, 0x01, KEY_NUMERIC_7)
+				MATRIX_KEY(0x01, 0x02, KEY_NUMERIC_8)
+				MATRIX_KEY(0x01, 0x03, KEY_NUMERIC_9)
+				MATRIX_KEY(0x00, 0x00, KEY_NUMERIC_D)
+				MATRIX_KEY(0x00, 0x01, KEY_CLEAR)
+				MATRIX_KEY(0x00, 0x02, KEY_NUMERIC_0)
+				MATRIX_KEY(0x00, 0x03, KEY_OK)
+		>;
+		keypad,num-rows = <4>;
+		keypad,num-columns = <4>;
+	};
+};
+
+&pio {
+	gpio-line-names = "", "", "", "", // PA
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "", // PB
+			  "", "", "UART3_TX", "UART3_RX",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "eMMC_CLK", "eMMC_CMD", // PC
+			  "eMMC_D2", "eMMC_D1", "eMMC_D0", "eMMC_D3",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "", // PD
+			  "", "", "", "",
+			  "", "USB_SEC_EN", "", "",
+			  "", "", "", "",
+			  "LED_STATUS_RED", "", "", "",
+			  "I2C2_SCL", "I2C2_SDA", "LED_STATUS_GREEN", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "ETH_CRSDV", "ETH_RXD0", "ETH_RXD1", "ETH_TXCK", // PE
+			  "ETH_TXD0", "ETH_TXD1", "ETH_TXEN", "",
+			  "ETH_MDC", "ETH_MDIO", "QWIIC_nINT", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "", // PF
+			  "", "", "KEY_nINT", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "ESP_CLK", "ESP_CMD", "ESP_D0", "ESP_D1", // PG
+			  "ESP_D2", "ESP_D3", "UART1_TXD", "UART1_RXD",
+			  "ESP_nBOOT", "ESP_nRST", "I2C3_SCL", "I2C3_SDA",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami.dtsi b/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami.dtsi
new file mode 100644
index 000000000000..544d60cfc32e
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-t113s-netcube-nagami.dtsi
@@ -0,0 +1,250 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2025 Lukas Schmid <lukas.schmid@netcube.li>
+ */
+
+/dts-v1/;
+#include "sun8i-t113s.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "NetCube Systems Nagami SoM";
+	compatible = "netcube,nagami", "allwinner,sun8i-t113s";
+
+	aliases {
+		serial1 = &uart1; // ESP32 Bootloader UART
+		serial3 = &uart3; // Console UART on Card Edge
+		ethernet0 = &emac;
+	};
+
+	chosen {
+		stdout-path = "serial3:115200n8";
+	};
+
+	/* module wide 3.3V supply directly from the card edge */
+	reg_vcc3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	/* SY8008 DC/DC regulator on the board, also supplying VDD-SYS */
+	reg_vcc_core: regulator-core {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-core";
+		regulator-min-microvolt = <880000>;
+		regulator-max-microvolt = <880000>;
+		vin-supply = <&reg_vcc3v3>;
+	};
+
+	/* USB0 MUX to switch connect to Card-Edge only after BootROM */
+	usb0_sec_mux: mux-controller{
+		compatible = "gpio-mux";
+		#mux-control-cells = <0>;
+		mux-gpios = <&pio 3 9 GPIO_ACTIVE_HIGH>; /* PD9 */
+		idle-state = <1>; /* USB connected to Card-Edge by default */
+	};
+
+	/* Reset of ESP32 */
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pio 6 9 GPIO_ACTIVE_LOW>; /* PG9 */
+		post-power-on-delay-ms = <1500>;
+		power-off-delay-us = <200>;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vcc_core>;
+};
+
+&cpu1 {
+	cpu-supply = <&reg_vcc_core>;
+};
+
+&dcxo {
+	clock-frequency = <24000000>;
+};
+
+&emac {
+	nvmem-cells = <&eth0_macaddress>;
+	nvmem-cell-names = "mac-address";
+	phy-handle = <&lan8720a>;
+	phy-mode = "rmii";
+	pinctrl-0 = <&rmii_pe_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/* Default I2C Interface on Card-Edge */
+&i2c2 {
+	pinctrl-0 = <&i2c2_pd_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+/* Exposed as the QWIIC connector and used by the internal EEPROM */
+&i2c3 {
+	pinctrl-0 = <&i2c3_pg_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	eeprom0: eeprom@50 {
+		compatible = "atmel,24c02";		/* actually it's a 24AA02E48 */
+		reg = <0x50>;
+		pagesize = <16>;
+		read-only;
+		vcc-supply = <&reg_vcc3v3>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		eth0_macaddress: macaddress@fa {
+			reg = <0xfa 0x06>;
+		};
+	};
+};
+
+/* Default I2S Interface on Card-Edge */
+&i2s1 {
+	pinctrl-0 = <&i2s1_pins>, <&i2s1_din0_pin>, <&i2s1_dout0_pin>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+/* Phy is on SoM. MDI signals pre-magnetics are on the card edge */
+&mdio {
+	lan8720a: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+/* Default SD Interface on Card-Edge */
+&mmc0 {
+	pinctrl-0 = <&mmc0_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+/* Connected to the on-board ESP32 */
+&mmc1 {
+	pinctrl-0 = <&mmc1_pins>;
+	pinctrl-names = "default";
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	non-removable;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	status = "okay";
+};
+
+/* Connected to the on-board eMMC */
+&mmc2 {
+	pinctrl-0 = <&mmc2_pins>;
+	pinctrl-names = "default";
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+&pio {
+	vcc-pb-supply = <&reg_vcc3v3>;
+	vcc-pc-supply = <&reg_vcc3v3>;
+	vcc-pd-supply = <&reg_vcc3v3>;
+	vcc-pe-supply = <&reg_vcc3v3>;
+	vcc-pf-supply = <&reg_vcc3v3>;
+	vcc-pg-supply = <&reg_vcc3v3>;
+
+	gpio-line-names = "", "", "", "", // PA
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "CAN0_TX", "CAN0_RX", // PB
+			  "CAN1_TX", "CAN1_RX", "UART3_TX", "UART3_RX",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "eMMC_CLK", "eMMC_CMD", // PC
+			  "eMMC_D2", "eMMC_D1", "eMMC_D0", "eMMC_D3",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "", // PD
+			  "", "", "", "",
+			  "", "USB_SEC_EN", "SPI1_CS", "SPI1_CLK",
+			  "SPI1_MOSI", "SPI1_MISO", "SPI1_HOLD", "SPI1_WP",
+			  "PD16", "", "", "",
+			  "I2C2_SCL", "I2C2_SDA", "PD22", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "ETH_CRSDV", "ETH_RXD0", "ETH_RXD1", "ETH_TXCK", // PE
+			  "ETH_TXD0", "ETH_TXD1", "ETH_TXEN", "",
+			  "ETH_MDC", "ETH_MDIO", "QWIIC_nINT", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "SD_D1", "SD_D0", "SD_CLK", "SD_CLK", // PF
+			  "SD_D3", "SD_D2", "PF6", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "ESP_CLK", "ESP_CMD", "ESP_D0", "ESP_D1", // PG
+			  "ESP_D2", "ESP_D3", "UART1_TXD", "UART1_RXD",
+			  "ESP_nBOOT", "ESP_nRST", "I2C3_SCL", "I2C3_SDA",
+			  "I2S1_WS", "I2S1_CLK", "I2S1_DIN0", "I2S1_DOUT0",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+/* Remove the unused CK pin from the pinctl as it is unconnected */
+&rmii_pe_pins {
+	pins = "PE0", "PE1", "PE2", "PE3", "PE4",
+	       "PE5", "PE6", "PE8", "PE9";
+};
+
+/* Default SPI Interface on Card-Edge */
+&spi1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-0 = <&spi1_pins>, <&spi1_hold_pin>, <&spi1_wp_pin>;
+	pinctrl-names = "default";
+	cs-gpios = <0>;
+	status = "disabled";
+};
+
+/* Connected to the Bootloader/Console of the ESP32 */
+&uart1 {
+	pinctrl-0 = <&uart1_pg6_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/* Console/Debug UART on Card-Edge */
+&uart3 {
+	pinctrl-0 = <&uart3_pb_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/allwinner/sun8i-t113s.dtsi b/arch/arm/boot/dts/allwinner/sun8i-t113s.dtsi
new file mode 100644
index 000000000000..c7181308ae6f
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-t113s.dtsi
@@ -0,0 +1,59 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2022 Arm Ltd.
+
+#define SOC_PERIPHERAL_IRQ(nr) GIC_SPI nr
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <riscv/allwinner/sunxi-d1s-t113.dtsi>
+#include <riscv/allwinner/sunxi-d1-t113.dtsi>
+
+/ {
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0>;
+			clocks = <&ccu CLK_CPUX>;
+			clock-names = "cpu";
+		};
+
+		cpu1: cpu@1 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <1>;
+			clocks = <&ccu CLK_CPUX>;
+			clock-names = "cpu";
+		};
+	};
+
+	gic: interrupt-controller@1c81000 {
+		compatible = "arm,gic-400";
+		reg = <0x03021000 0x1000>,
+		      <0x03022000 0x2000>,
+		      <0x03024000 0x2000>,
+		      <0x03026000 0x2000>;
+		interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+		interrupt-controller;
+		#interrupt-cells = <3>;
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>;
+	};
+};
diff --git a/arch/arm/boot/dts/sun8i-t3-cqa3t-bv3.dts b/arch/arm/boot/dts/allwinner/sun8i-t3-cqa3t-bv3.dts
index 6931aaab2382..9f472521f4a4 100644
--- a/arch/arm/boot/dts/sun8i-t3-cqa3t-bv3.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-t3-cqa3t-bv3.dts
@@ -45,6 +45,7 @@
 
 /dts-v1/;
 #include "sun8i-r40.dtsi"
+#include "sun8i-r40-cpu-opp.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
 
@@ -88,6 +89,10 @@
 	status = "okay";
 };
 
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
 &de {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/sun8i-v3-sl631-imx179.dts b/arch/arm/boot/dts/allwinner/sun8i-v3-sl631-imx179.dts
index 117aeece4e55..117aeece4e55 100644
--- a/arch/arm/boot/dts/sun8i-v3-sl631-imx179.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-v3-sl631-imx179.dts
diff --git a/arch/arm/boot/dts/sun8i-v3-sl631.dtsi b/arch/arm/boot/dts/allwinner/sun8i-v3-sl631.dtsi
index 6f93f8c49f84..6f93f8c49f84 100644
--- a/arch/arm/boot/dts/sun8i-v3-sl631.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-v3-sl631.dtsi
diff --git a/arch/arm/boot/dts/sun8i-v3.dtsi b/arch/arm/boot/dts/allwinner/sun8i-v3.dtsi
index 186c30cbe6ee..95bd0b616349 100644
--- a/arch/arm/boot/dts/sun8i-v3.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-v3.dtsi
@@ -56,6 +56,15 @@
 		function = "i2s";
 	};
 
+	/omit-if-no-ref/
+	lcd_rgb666_pd_pins: lcd-rgb666-pd-pins {
+		pins = "PD0", "PD1", "PD2", "PD3", "PD4", "PD5",
+		       "PD6", "PD7", "PD8", "PD9", "PD10", "PD11",
+		       "PD12", "PD13", "PD14", "PD15", "PD16", "PD17",
+		       "PD18", "PD19", "PD20", "PD21";
+		function = "lcd";
+	};
+
 	uart1_pg_pins: uart1-pg-pins {
 		pins = "PG6", "PG7";
 		function = "uart1";
diff --git a/arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg-nano.dts b/arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg-nano.dts
new file mode 100644
index 000000000000..f34dfdf1566d
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-v3s-anbernic-rg-nano.dts
@@ -0,0 +1,276 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+#include <dt-bindings/input/linux-event-codes.h>
+#include "sun8i-v3s.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+/ {
+	model = "Anbernic RG Nano";
+	compatible = "anbernic,rg-nano", "allwinner,sun8i-v3s";
+
+	aliases {
+		rtc0 = &pcf8563;
+		rtc1 = &rtc;
+		serial0 = &uart0;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		brightness-levels = <0 1 2 3 8 14 21 32 46 60 80 100>;
+		default-brightness-level = <11>;
+		power-supply = <&reg_vcc5v0>;
+		pwms = <&pwm 0 40000 1>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+
+		button-a {
+			gpios = <&gpio_expander 12 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "BTN-A";
+			linux,code = <BTN_EAST>;
+		};
+
+		button-b {
+			gpios = <&gpio_expander 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "BTN-B";
+			linux,code = <BTN_SOUTH>;
+		};
+
+		button-down {
+			gpios = <&gpio_expander 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "DPAD-DOWN";
+			linux,code = <BTN_DPAD_DOWN>;
+		};
+
+		button-left {
+			gpios = <&gpio_expander 4 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "DPAD-LEFT";
+			linux,code = <BTN_DPAD_LEFT>;
+		};
+
+		button-right {
+			gpios = <&gpio_expander 0 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "DPAD-RIGHT";
+			linux,code = <BTN_DPAD_RIGHT>;
+		};
+
+		button-se {
+			gpios = <&gpio_expander 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "BTN-SELECT";
+			linux,code = <BTN_SELECT>;
+		};
+
+		button-st {
+			gpios = <&gpio_expander 6 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "BTN-START";
+			linux,code = <BTN_START>;
+		};
+
+		button-tl {
+			gpios = <&gpio_expander 2 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "BTN-L";
+			linux,code = <BTN_TL>;
+		};
+
+		button-tr {
+			gpios = <&gpio_expander 15 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "BTN-R";
+			linux,code = <BTN_TR>;
+		};
+
+		button-up {
+			gpios = <&gpio_expander 3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "DPAD-UP";
+			linux,code = <BTN_DPAD_UP>;
+		};
+
+		button-x {
+			gpios = <&gpio_expander 11 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "BTN-X";
+			linux,code = <BTN_NORTH>;
+		};
+
+		button-y {
+			gpios = <&gpio_expander 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+			label = "BTN-Y";
+			linux,code = <BTN_WEST>;
+		};
+	};
+};
+
+&codec {
+	allwinner,audio-routing = "Speaker", "HP",
+				  "MIC1", "Mic",
+				  "Mic", "HBIAS";
+	allwinner,pa-gpios = <&pio 5 6 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PF6 */
+	status = "okay";
+};
+
+&ehci {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	gpio_expander: gpio@20 {
+		compatible = "nxp,pcal6416";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		interrupt-parent = <&pio>;
+		interrupts = <1 3 IRQ_TYPE_EDGE_BOTH>; /* PB3/EINT3 */
+		vcc-supply = <&reg_vcc3v3>;
+	};
+
+	axp209: pmic@34 {
+		reg = <0x34>;
+		interrupt-parent = <&pio>;
+		interrupts = <1 5 IRQ_TYPE_EDGE_FALLING>; /* PB5/EINT5 */
+	};
+
+	pcf8563: rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+#include "axp209.dtsi"
+
+&battery_power_supply {
+	status = "okay";
+};
+
+&mmc0 {
+	broken-cd;
+	bus-width = <4>;
+	disable-wp;
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	status = "okay";
+};
+
+&ohci {
+	status = "okay";
+};
+
+&pio {
+	vcc-pb-supply = <&reg_vcc3v3>;
+	vcc-pc-supply = <&reg_vcc3v3>;
+	vcc-pf-supply = <&reg_vcc3v3>;
+	vcc-pg-supply = <&reg_vcc3v3>;
+
+	spi0_no_miso_pins: spi0-no-miso-pins {
+		pins = "PC1", "PC2", "PC3";
+		function = "spi0";
+	};
+};
+
+&pwm {
+	pinctrl-0 = <&pwm0_pin>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/* DCDC2 wired into vdd-cpu, vdd-sys, and vdd-ephy. */
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-max-microvolt = <1250000>;
+	regulator-min-microvolt = <1250000>;
+	regulator-name = "vdd-cpu";
+};
+
+/* DCDC3 wired into every 3.3v input that isn't the RTC. */
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-max-microvolt = <3300000>;
+	regulator-min-microvolt = <3300000>;
+	regulator-name = "vcc-io";
+};
+
+/* LDO1 wired into RTC, voltage is hard-wired at 3.3v. */
+&reg_ldo1 {
+	regulator-always-on;
+	regulator-name = "vcc-rtc";
+};
+
+/* LDO2 wired into VCC-PLL and audio codec. */
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-max-microvolt = <3000000>;
+	regulator-min-microvolt = <3000000>;
+	regulator-name = "vcc-pll";
+};
+
+/* LDO3, LDO4, and LDO5 unused. */
+&reg_ldo3 {
+	status = "disabled";
+};
+
+&reg_ldo4 {
+	status = "disabled";
+};
+
+/* RTC uses internal oscillator */
+&rtc {
+	/delete-property/ clocks;
+};
+
+&spi0 {
+	pinctrl-0 = <&spi0_no_miso_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	display@0 {
+		compatible = "saef,sftc154b", "panel-mipi-dbi-spi";
+		reg = <0>;
+		backlight = <&backlight>;
+		dc-gpios = <&pio 2 0 GPIO_ACTIVE_HIGH>; /* PC0 */
+		reset-gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 */
+		spi-max-frequency = <100000000>;
+
+		height-mm = <39>;
+		width-mm = <39>;
+
+		/* Set hb-porch to compensate for non-visible area */
+		panel-timing {
+			hactive = <240>;
+			vactive = <240>;
+			hback-porch = <80>;
+			vback-porch = <0>;
+			clock-frequency = <0>;
+			hfront-porch = <0>;
+			hsync-len = <0>;
+			vfront-porch = <0>;
+			vsync-len = <0>;
+		};
+	};
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_pb_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb_power_supply {
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 6 5 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PG5 */
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dts b/arch/arm/boot/dts/allwinner/sun8i-v3s-licheepi-zero-dock.dts
index 752ad05c8f83..752ad05c8f83 100644
--- a/arch/arm/boot/dts/sun8i-v3s-licheepi-zero-dock.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-v3s-licheepi-zero-dock.dts
diff --git a/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dts b/arch/arm/boot/dts/allwinner/sun8i-v3s-licheepi-zero.dts
index 2e4587d26ce5..2e4587d26ce5 100644
--- a/arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-v3s-licheepi-zero.dts
diff --git a/arch/arm/boot/dts/allwinner/sun8i-v3s-netcube-kumquat.dts b/arch/arm/boot/dts/allwinner/sun8i-v3s-netcube-kumquat.dts
new file mode 100644
index 000000000000..cb6292319f39
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-v3s-netcube-kumquat.dts
@@ -0,0 +1,276 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2025 Lukas Schmid <lukas.schmid@netcube.li>
+ */
+
+/dts-v1/;
+#include "sun8i-v3s.dtsi"
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/{
+	model = "NetCube Systems Kumquat";
+	compatible = "netcube,kumquat", "allwinner,sun8i-v3s";
+
+	aliases {
+		serial0 = &uart0;
+		ethernet0 = &emac;
+		rtc0 = &ds3232;
+		rtc1 = &rtc; /* not battery backed */
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	/* 40 MHz Crystal Oscillator on PCB */
+	clk_can0: clock-can0 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <40000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		key-user {
+			label = "GPIO Key User";
+			linux,code = <KEY_PROG1>;
+			gpios = <&pio 1 2 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PB2 */
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-heartbeat {
+			gpios = <&pio 4 4 GPIO_ACTIVE_HIGH>; /* PE4 */
+			linux,default-trigger = "heartbeat";
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_HEARTBEAT;
+		};
+
+		led-mmc0-act {
+			gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+			linux,default-trigger = "mmc0";
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_DISK;
+		};
+	};
+
+	/* EA3036C Switching 3 Channel Regulator - Channel 2 */
+	reg_vcc3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_vcc5v0>;
+	};
+
+	/* K7805-1000R3 Switching Regulator supplied from main 12/24V terminal block */
+	reg_vcc5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+};
+
+&codec {
+	allwinner,audio-routing =
+		"Headphone", "HP",
+		"Headphone", "HPCOM",
+		"MIC1", "Mic",
+		"Mic", "HBIAS";
+	status = "okay";
+};
+
+&ehci {
+	status = "okay";
+};
+
+&emac {
+	allwinner,leds-active-low;
+	nvmem-cells = <&eth0_macaddress>;
+	nvmem-cell-names = "mac-address";
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	eeprom0: eeprom@50 {
+		compatible = "atmel,24c02";		/* actually it's a 24AA02E48 */
+		reg = <0x50>;
+		pagesize = <16>;
+		read-only;
+		vcc-supply = <&reg_vcc3v3>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		eth0_macaddress: macaddress@fa {
+			reg = <0xfa 0x06>;
+		};
+	};
+
+	tusb320: typec@60 {
+		compatible = "ti,tusb320";
+		reg = <0x60>;
+		interrupts-extended = <&pio 1 5 IRQ_TYPE_LEVEL_LOW>;  /* PB5 */
+	};
+
+	ds3232: rtc@68 {
+		compatible = "dallas,ds3232";
+		reg = <0x68>;
+	};
+};
+
+/* Exposed as the Flash/SD Header on the board */
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	broken-cd;
+	status = "okay";
+};
+
+/* Connected to the on-board ESP32 */
+&mmc1 {
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	broken-cd;
+	status = "okay";
+};
+
+&ohci {
+	status = "okay";
+};
+
+/* Disable external 32k osc as it is broken on current revision */
+&osc32k {
+	status = "disabled";
+};
+
+&pio {
+	vcc-pb-supply = <&reg_vcc3v3>;
+	vcc-pc-supply = <&reg_vcc3v3>;
+	vcc-pe-supply = <&reg_vcc3v3>;
+	vcc-pf-supply = <&reg_vcc3v3>;
+	vcc-pg-supply = <&reg_vcc3v3>;
+
+	gpio-line-names = "", "", "", "", // PA
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "CAN_nCS", "CAN_nINT", "USER_SW", "PB3", // PB
+			  "USB_ID", "USBC_nINT", "I2C0_SCL", "I2C0_SDA",
+			  "UART0_TX", "UART0_RX", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "SPI_MISO", "SPI_SCK", "FLASH_nCS", "SPI_MOSI", // PC
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "", // PD
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "Q12", "Q11", "Q10", "Q9", // PE
+			  "LED_SYS0", "I1", "Q1", "Q2",
+			  "I2", "I3", "Q3", "Q4",
+			  "I4", "I5", "Q5", "Q6",
+			  "I6", "I7", "Q7", "Q8",
+			  "I8", "UART1_TXD", "UART1_RXD", "ESP_nRST",
+			  "ESP_nBOOT", "", "", "",
+			  "", "", "", "",
+			  "SD_D1", "SD_D0", "SD_CLK", "SD_CMD", // PF
+			  "SD_D3", "SD_D2", "LED_SYS1", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "ESP_CLK", "ESP_CMD", "ESP_D0", "ESP_D1", // PG
+			  "ESP_D2", "ESP_D3", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+/* Disable external 32k osc as it is broken on current revision */
+&rtc {
+	/delete-property/ clocks;
+};
+
+/* Exposed as a USB-C connector with USB-Serial converter */
+&uart0 {
+	pinctrl-0 = <&uart0_pb_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/* Connected to the Bootloader/Console of the ESP32 */
+&uart1 {
+	pinctrl-0 = <&uart1_pe_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usb_otg {
+	extcon = <&tusb320 0>;
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
+	status = "okay";
+};
+
+&spi0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	cs-gpios = <0>, <&pio 1 0 GPIO_ACTIVE_LOW>; /* PB0 */
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		label = "firmware";
+		spi-max-frequency = <40000000>;
+	};
+
+	can@1 {
+		compatible = "microchip,mcp2518fd";
+		reg = <1>;
+		clocks = <&clk_can0>;
+		interrupts-extended = <&pio 1 1 IRQ_TYPE_LEVEL_LOW>;  /* PB1 */
+		spi-max-frequency = <20000000>;
+		vdd-supply = <&reg_vcc3v3>;
+		xceiver-supply = <&reg_vcc3v3>;
+	};
+};
diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi
index 084323d5c61c..fa54510319ac 100644
--- a/arch/arm/boot/dts/sun8i-v3s.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun8i-v3s.dtsi
@@ -42,6 +42,7 @@
  */
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/sun6i-rtc.h>
 #include <dt-bindings/clock/sun8i-v3s-ccu.h>
 #include <dt-bindings/reset/sun8i-v3s-ccu.h>
 #include <dt-bindings/clock/sun8i-de2.h>
@@ -97,7 +98,7 @@
 		#size-cells = <1>;
 		ranges;
 
-		osc24M: osc24M_clk {
+		osc24M: osc24M-clk {
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <24000000>;
@@ -105,7 +106,7 @@
 			clock-output-names = "osc24M";
 		};
 
-		osc32k: osc32k_clk {
+		osc32k: osc32k-clk {
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <32768>;
@@ -190,7 +191,7 @@
 				 <&ccu CLK_TCON0>;
 			clock-names = "ahb",
 				      "tcon-ch0";
-			clock-output-names = "tcon-pixel-clock";
+			clock-output-names = "tcon-data-clock";
 			#clock-cells = <0>;
 			resets = <&ccu RST_BUS_TCON0>;
 			reset-names = "lcd";
@@ -318,10 +319,33 @@
 			#phy-cells = <1>;
 		};
 
+		ehci: usb@1c1a000 {
+			compatible = "allwinner,sun8i-v3s-ehci", "generic-ehci";
+			reg = <0x01c1a000 0x100>;
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_EHCI0>, <&ccu CLK_BUS_OHCI0>;
+			resets = <&ccu RST_BUS_EHCI0>, <&ccu RST_BUS_OHCI0>;
+			phys = <&usbphy 0>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
+		ohci: usb@1c1a400 {
+			compatible = "allwinner,sun8i-v3s-ohci", "generic-ohci";
+			reg = <0x01c1a400 0x100>;
+			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_EHCI0>, <&ccu CLK_BUS_OHCI0>,
+				 <&ccu CLK_USB_OHCI0>;
+			resets = <&ccu RST_BUS_EHCI0>, <&ccu RST_BUS_OHCI0>;
+			phys = <&usbphy 0>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
 		ccu: clock@1c20000 {
 			compatible = "allwinner,sun8i-v3s-ccu";
 			reg = <0x01c20000 0x400>;
-			clocks = <&osc24M>, <&rtc 0>;
+			clocks = <&osc24M>, <&rtc CLK_OSC32K>;
 			clock-names = "hosc", "losc";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -342,7 +366,8 @@
 			reg = <0x01c20800 0x400>;
 			interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&rtc 0>;
+			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>,
+				 <&rtc CLK_OSC32K>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			#gpio-cells = <3>;
@@ -386,11 +411,26 @@
 				function = "i2c1";
 			};
 
+			/omit-if-no-ref/
+			lcd_rgb666_pe_pins: lcd-rgb666-pe-pins {
+				pins = "PE0", "PE1", "PE2", "PE3", "PE4", "PE5",
+				       "PE6", "PE7", "PE8", "PE9", "PE10", "PE11",
+				       "PE12", "PE13", "PE14", "PE15", "PE16", "PE17",
+				       "PE18", "PE19", "PE23", "PE24";
+				function = "lcd";
+			};
+
 			uart0_pb_pins: uart0-pb-pins {
 				pins = "PB8", "PB9";
 				function = "uart0";
 			};
 
+			/omit-if-no-ref/
+			uart1_pe_pins: uart1-pe-pins {
+				pins = "PE21", "PE22";
+				function = "uart1";
+			};
+
 			uart2_pins: uart2-pins {
 				pins = "PB0", "PB1";
 				function = "uart2";
@@ -412,6 +452,18 @@
 				bias-pull-up;
 			};
 
+			/omit-if-no-ref/
+			pwm0_pin: pwm0-pin {
+				pins = "PB4";
+				function = "pwm0";
+			};
+
+			/omit-if-no-ref/
+			pwm1_pin: pwm1-pin {
+				pins = "PB5";
+				function = "pwm1";
+			};
+
 			spi0_pins: spi0-pins {
 				pins = "PC0", "PC1", "PC2", "PC3";
 				function = "spi0";
@@ -477,7 +529,7 @@
 			reg-io-width = <4>;
 			clocks = <&ccu CLK_BUS_UART0>;
 			dmas = <&dma 6>, <&dma 6>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			resets = <&ccu RST_BUS_UART0>;
 			status = "disabled";
 		};
@@ -490,7 +542,7 @@
 			reg-io-width = <4>;
 			clocks = <&ccu CLK_BUS_UART1>;
 			dmas = <&dma 7>, <&dma 7>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			resets = <&ccu RST_BUS_UART1>;
 			status = "disabled";
 		};
@@ -503,7 +555,7 @@
 			reg-io-width = <4>;
 			clocks = <&ccu CLK_BUS_UART2>;
 			dmas = <&dma 8>, <&dma 8>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			resets = <&ccu RST_BUS_UART2>;
 			pinctrl-0 = <&uart2_pins>;
 			pinctrl-names = "default";
@@ -609,7 +661,7 @@
 			reg = <0x01cb4000 0x3000>;
 			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_CSI>,
-				 <&ccu CLK_CSI1_SCLK>,
+				 <&ccu CLK_CSI_SCLK>,
 				 <&ccu CLK_DRAM_CSI>;
 			clock-names = "bus", "mod", "ram";
 			resets = <&ccu RST_BUS_CSI>;
diff --git a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts b/arch/arm/boot/dts/allwinner/sun8i-v40-bananapi-m2-berry.dts
index 47954551f573..6575ef274453 100644
--- a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
+++ b/arch/arm/boot/dts/allwinner/sun8i-v40-bananapi-m2-berry.dts
@@ -42,6 +42,7 @@
 
 /dts-v1/;
 #include "sun8i-r40.dtsi"
+#include "sun8i-r40-cpu-opp.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
 
@@ -93,7 +94,7 @@
 		enable-active-high;
 	};
 
-	wifi_pwrseq: wifi_pwrseq {
+	wifi_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 WIFI_EN */
 		clocks = <&ccu CLK_OUTA>;
@@ -107,6 +108,10 @@
 	status = "okay";
 };
 
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
 &de {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/allwinner/sun9i-a80-cubieboard4.dts
index c8ca8cb7f5c9..52ad95a2063a 100644
--- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
+++ b/arch/arm/boot/dts/allwinner/sun9i-a80-cubieboard4.dts
@@ -280,8 +280,8 @@
 
 			reg_dcdc5: dcdc5 {
 				regulator-always-on;
-				regulator-min-microvolt = <1425000>;
-				regulator-max-microvolt = <1575000>;
+				regulator-min-microvolt = <1450000>;
+				regulator-max-microvolt = <1550000>;
 				regulator-name = "vcc-dram";
 			};
 
diff --git a/arch/arm/boot/dts/sun9i-a80-optimus.dts b/arch/arm/boot/dts/allwinner/sun9i-a80-optimus.dts
index 5c3580d712e4..5c3580d712e4 100644
--- a/arch/arm/boot/dts/sun9i-a80-optimus.dts
+++ b/arch/arm/boot/dts/allwinner/sun9i-a80-optimus.dts
diff --git a/arch/arm/boot/dts/sun9i-a80.dtsi b/arch/arm/boot/dts/allwinner/sun9i-a80.dtsi
index ce4fa6706d06..a1ae0929cec9 100644
--- a/arch/arm/boot/dts/sun9i-a80.dtsi
+++ b/arch/arm/boot/dts/allwinner/sun9i-a80.dtsi
@@ -196,14 +196,14 @@
 		 * The actual TX clock rate is not controlled by the
 		 * gmac_tx clock.
 		 */
-		mii_phy_tx_clk: mii_phy_tx_clk {
+		mii_phy_tx_clk: mii-phy-tx-clk {
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <25000000>;
 			clock-output-names = "mii_phy_tx";
 		};
 
-		gmac_int_tx_clk: gmac_int_tx_clk {
+		gmac_int_tx_clk: gmac-int-tx-clk {
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <125000000>;
@@ -1218,7 +1218,6 @@
 				     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&apbs_gates 0>, <&osc24M>, <&osc32k>;
 			clock-names = "apb", "hosc", "losc";
-			resets = <&apbs_rst 0>;
 			gpio-controller;
 			interrupt-controller;
 			#interrupt-cells = <3>;
diff --git a/arch/arm/boot/dts/allwinner/suniv-f1c100s-licheepi-nano.dts b/arch/arm/boot/dts/allwinner/suniv-f1c100s-licheepi-nano.dts
new file mode 100644
index 000000000000..472ded0aafcf
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/suniv-f1c100s-licheepi-nano.dts
@@ -0,0 +1,81 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR X11)
+/*
+ * Copyright 2018 Icenowy Zheng <icenowy@aosc.io>
+ */
+
+/dts-v1/;
+#include "suniv-f1c100s.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Lichee Pi Nano";
+	compatible = "licheepi,licheepi-nano", "allwinner,suniv-f1c100s";
+
+	aliases {
+		mmc0 = &mmc0;
+		serial0 = &uart0;
+		spi0 = &spi0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_vcc3v3: vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&mmc0 {
+	broken-cd;
+	bus-width = <4>;
+	disable-wp;
+	status = "okay";
+	vmmc-supply = <&reg_vcc3v3>;
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pc_pins>;
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "winbond,w25q128", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+	};
+};
+
+&otg_sram {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pe_pins>;
+	status = "okay";
+};
+
+&codec {
+	allwinner,audio-routing =
+		"Headphone", "HP",
+		"Headphone", "HPCOM",
+		"MIC", "Mic";
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 4 2 GPIO_ACTIVE_HIGH>; /* PE2 */
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/allwinner/suniv-f1c100s.dtsi b/arch/arm/boot/dts/allwinner/suniv-f1c100s.dtsi
new file mode 100644
index 000000000000..e4b41bc93852
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/suniv-f1c100s.dtsi
@@ -0,0 +1,354 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR X11)
+/*
+ * Copyright 2018 Icenowy Zheng <icenowy@aosc.io>
+ * Copyright 2018 Mesih Kilinc <mesihkilinc@gmail.com>
+ */
+
+#include <dt-bindings/clock/suniv-ccu-f1c100s.h>
+#include <dt-bindings/reset/suniv-ccu-f1c100s.h>
+#include <dt-bindings/dma/sun4i-a10.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&intc>;
+
+	clocks {
+		osc24M: clk-24M {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <24000000>;
+			clock-output-names = "osc24M";
+		};
+
+		osc32k: clk-32k {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+			clock-output-names = "osc32k";
+		};
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "arm,arm926ej-s";
+			device_type = "cpu";
+			reg = <0x0>;
+		};
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		sram-controller@1c00000 {
+			compatible = "allwinner,suniv-f1c100s-system-control",
+				     "allwinner,sun4i-a10-system-control";
+			reg = <0x01c00000 0x30>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			sram_d: sram@10000 {
+				compatible = "mmio-sram";
+				reg = <0x00010000 0x1000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x00010000 0x1000>;
+
+				otg_sram: sram-section@0 {
+					compatible = "allwinner,suniv-f1c100s-sram-d",
+						     "allwinner,sun4i-a10-sram-d";
+					reg = <0x0000 0x1000>;
+					status = "disabled";
+				};
+			};
+		};
+
+		spi0: spi@1c05000 {
+			compatible = "allwinner,suniv-f1c100s-spi",
+				     "allwinner,sun8i-h3-spi";
+			reg = <0x01c05000 0x1000>;
+			interrupts = <10>;
+			clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_BUS_SPI0>;
+			clock-names = "ahb", "mod";
+			resets = <&ccu RST_BUS_SPI0>;
+			status = "disabled";
+			num-cs = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		spi1: spi@1c06000 {
+			compatible = "allwinner,suniv-f1c100s-spi",
+				     "allwinner,sun8i-h3-spi";
+			reg = <0x01c06000 0x1000>;
+			interrupts = <11>;
+			clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_BUS_SPI1>;
+			clock-names = "ahb", "mod";
+			resets = <&ccu RST_BUS_SPI1>;
+			status = "disabled";
+			num-cs = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc0: mmc@1c0f000 {
+			compatible = "allwinner,suniv-f1c100s-mmc",
+				     "allwinner,sun7i-a20-mmc";
+			reg = <0x01c0f000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC0>,
+				 <&ccu CLK_MMC0>,
+				 <&ccu CLK_MMC0_OUTPUT>,
+				 <&ccu CLK_MMC0_SAMPLE>;
+			clock-names = "ahb", "mmc", "output", "sample";
+			resets = <&ccu RST_BUS_MMC0>;
+			reset-names = "ahb";
+			interrupts = <23>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc0_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc1: mmc@1c10000 {
+			compatible = "allwinner,suniv-f1c100s-mmc",
+				     "allwinner,sun7i-a20-mmc";
+			reg = <0x01c10000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC1>,
+				 <&ccu CLK_MMC1>,
+				 <&ccu CLK_MMC1_OUTPUT>,
+				 <&ccu CLK_MMC1_SAMPLE>;
+			clock-names = "ahb", "mmc", "output", "sample";
+			resets = <&ccu RST_BUS_MMC1>;
+			reset-names = "ahb";
+			interrupts = <24>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		usb_otg: usb@1c13000 {
+			compatible = "allwinner,suniv-f1c100s-musb";
+			reg = <0x01c13000 0x0400>;
+			clocks = <&ccu CLK_BUS_OTG>;
+			resets = <&ccu RST_BUS_OTG>;
+			interrupts = <26>;
+			interrupt-names = "mc";
+			phys = <&usbphy 0>;
+			phy-names = "usb";
+			extcon = <&usbphy 0>;
+			allwinner,sram = <&otg_sram 1>;
+			status = "disabled";
+		};
+
+		usbphy: phy@1c13400 {
+			compatible = "allwinner,suniv-f1c100s-usb-phy";
+			reg = <0x01c13400 0x10>;
+			reg-names = "phy_ctrl";
+			clocks = <&ccu CLK_USB_PHY0>;
+			clock-names = "usb0_phy";
+			resets = <&ccu RST_USB_PHY0>;
+			reset-names = "usb0_reset";
+			#phy-cells = <1>;
+			status = "disabled";
+		};
+
+		dma: dma-controller@1c02000 {
+			compatible = "allwinner,suniv-f1c100s-dma";
+			reg = <0x01c02000 0x1000>;
+			interrupts = <18>;
+			clocks = <&ccu CLK_BUS_DMA>;
+			resets = <&ccu RST_BUS_DMA>;
+			#dma-cells = <2>;
+		};
+
+		ccu: clock@1c20000 {
+			compatible = "allwinner,suniv-f1c100s-ccu";
+			reg = <0x01c20000 0x400>;
+			clocks = <&osc24M>, <&osc32k>;
+			clock-names = "hosc", "losc";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		intc: interrupt-controller@1c20400 {
+			compatible = "allwinner,suniv-f1c100s-ic";
+			reg = <0x01c20400 0x400>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		pio: pinctrl@1c20800 {
+			compatible = "allwinner,suniv-f1c100s-pinctrl";
+			reg = <0x01c20800 0x400>;
+			interrupts = <38>, <39>, <40>;
+			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
+			clock-names = "apb", "hosc", "losc";
+			gpio-controller;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			#gpio-cells = <3>;
+
+			mmc0_pins: mmc0-pins {
+				pins = "PF0", "PF1", "PF2", "PF3", "PF4", "PF5";
+				function = "mmc0";
+				drive-strength = <30>;
+			};
+
+			/omit-if-no-ref/
+			i2c0_pd_pins: i2c0-pd-pins {
+				pins = "PD0", "PD12";
+				function = "i2c0";
+			};
+
+			spi0_pc_pins: spi0-pc-pins {
+				pins = "PC0", "PC1", "PC2", "PC3";
+				function = "spi0";
+			};
+
+			uart0_pe_pins: uart0-pe-pins {
+				pins = "PE0", "PE1";
+				function = "uart0";
+			};
+
+			/omit-if-no-ref/
+			uart1_pa_pins: uart1-pa-pins {
+				pins = "PA2", "PA3";
+				function = "uart1";
+			};
+		};
+
+		i2c0: i2c@1c27000 {
+			compatible = "allwinner,suniv-f1c100s-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x01c27000 0x400>;
+			interrupts = <7>;
+			clocks = <&ccu CLK_BUS_I2C0>;
+			resets = <&ccu RST_BUS_I2C0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@1c27400 {
+			compatible = "allwinner,suniv-f1c100s-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x01c27400 0x400>;
+			interrupts = <8>;
+			clocks = <&ccu CLK_BUS_I2C1>;
+			resets = <&ccu RST_BUS_I2C1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@1c27800 {
+			compatible = "allwinner,suniv-f1c100s-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x01c27800 0x400>;
+			interrupts = <9>;
+			clocks = <&ccu CLK_BUS_I2C2>;
+			resets = <&ccu RST_BUS_I2C2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		timer@1c20c00 {
+			compatible = "allwinner,suniv-f1c100s-timer";
+			reg = <0x01c20c00 0x90>;
+			interrupts = <13>, <14>, <15>;
+			clocks = <&osc24M>;
+		};
+
+		wdt: watchdog@1c20ca0 {
+			compatible = "allwinner,suniv-f1c100s-wdt",
+				     "allwinner,sun6i-a31-wdt";
+			reg = <0x01c20ca0 0x20>;
+			interrupts = <16>;
+			clocks = <&osc32k>;
+		};
+
+		pwm: pwm@1c21000 {
+			compatible = "allwinner,suniv-f1c100s-pwm",
+				     "allwinner,sun7i-a20-pwm";
+			reg = <0x01c21000 0x400>;
+			clocks = <&osc24M>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
+		ir: ir@1c22c00 {
+			compatible = "allwinner,suniv-f1c100s-ir",
+				     "allwinner,sun6i-a31-ir";
+			reg = <0x01c22c00 0x400>;
+			clocks = <&ccu CLK_BUS_IR>, <&ccu CLK_IR>;
+			clock-names = "apb", "ir";
+			resets = <&ccu RST_BUS_IR>;
+			interrupts = <6>;
+			status = "disabled";
+		};
+
+		lradc: lradc@1c23400 {
+			compatible = "allwinner,suniv-f1c100s-lradc",
+				     "allwinner,sun8i-a83t-r-lradc";
+			reg = <0x01c23400 0x400>;
+			interrupts = <22>;
+			status = "disabled";
+		};
+
+		uart0: serial@1c25000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c25000 0x400>;
+			interrupts = <1>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART0>;
+			resets = <&ccu RST_BUS_UART0>;
+			status = "disabled";
+		};
+
+		uart1: serial@1c25400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c25400 0x400>;
+			interrupts = <2>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART1>;
+			resets = <&ccu RST_BUS_UART1>;
+			status = "disabled";
+		};
+
+		uart2: serial@1c25800 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c25800 0x400>;
+			interrupts = <3>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART2>;
+			resets = <&ccu RST_BUS_UART2>;
+			status = "disabled";
+		};
+
+		codec: codec@1c23c00 {
+			#sound-dai-cells = <0>;
+			compatible = "allwinner,suniv-f1c100s-codec";
+			reg = <0x01c23c00 0x400>;
+			interrupts = <21>;
+			clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_CODEC>;
+			clock-names = "apb", "codec";
+			dmas = <&dma SUN4I_DMA_NORMAL 12>,
+			       <&dma SUN4I_DMA_NORMAL 12>;
+			dma-names = "rx", "tx";
+			resets = <&ccu RST_BUS_CODEC>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/allwinner/suniv-f1c200s-lctech-pi.dts b/arch/arm/boot/dts/allwinner/suniv-f1c200s-lctech-pi.dts
new file mode 100644
index 000000000000..2d2a3f026df3
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/suniv-f1c200s-lctech-pi.dts
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Arm Ltd,
+ * based on work:
+ *   Copyright 2022 Icenowy Zheng <uwu@icenowy.me>
+ */
+
+/dts-v1/;
+#include "suniv-f1c100s.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Lctech Pi F1C200s";
+	compatible = "lctech,pi-f1c200s", "allwinner,suniv-f1c200s",
+		     "allwinner,suniv-f1c100s";
+
+	aliases {
+		serial0 = &uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_vcc3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&mmc0 {
+	broken-cd;
+	bus-width = <4>;
+	disable-wp;
+	vmmc-supply = <&reg_vcc3v3>;
+	status = "okay";
+};
+
+&otg_sram {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pc_pins>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "spi-nand";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pa_pins>;
+	status = "okay";
+};
+
+/*
+ * This is a Type-C socket, but CC1/2 are not connected, and VBUS is connected
+ * to Vin, which supplies the board. Host mode works (if the board is powered
+ * otherwise), but peripheral is probably the intention.
+ */
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/allwinner/suniv-f1c200s-popstick-v1.1.dts b/arch/arm/boot/dts/allwinner/suniv-f1c200s-popstick-v1.1.dts
new file mode 100644
index 000000000000..184c245041a6
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/suniv-f1c200s-popstick-v1.1.dts
@@ -0,0 +1,81 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Icenowy Zheng <uwu@icenowy.me>
+ */
+
+/dts-v1/;
+#include "suniv-f1c100s.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Popcorn Computer PopStick v1.1";
+	compatible = "sourceparts,popstick-v1.1", "sourceparts,popstick",
+		     "allwinner,suniv-f1c200s", "allwinner,suniv-f1c100s";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pio 4 6 GPIO_ACTIVE_HIGH>; /* PE6 */
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	reg_vcc3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&mmc0 {
+	cd-gpios = <&pio 4 3 GPIO_ACTIVE_LOW>; /* PE3 */
+	bus-width = <4>;
+	disable-wp;
+	vmmc-supply = <&reg_vcc3v3>;
+	status = "okay";
+};
+
+&otg_sram {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pc_pins>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "spi-nand";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pe_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sunxi-bananapi-m2-plus-v1.2.dtsi b/arch/arm/boot/dts/allwinner/sunxi-bananapi-m2-plus-v1.2.dtsi
index 235994a4a2eb..235994a4a2eb 100644
--- a/arch/arm/boot/dts/sunxi-bananapi-m2-plus-v1.2.dtsi
+++ b/arch/arm/boot/dts/allwinner/sunxi-bananapi-m2-plus-v1.2.dtsi
diff --git a/arch/arm/boot/dts/sunxi-bananapi-m2-plus.dtsi b/arch/arm/boot/dts/allwinner/sunxi-bananapi-m2-plus.dtsi
index d03f5853ef7b..873817ddb4ea 100644
--- a/arch/arm/boot/dts/sunxi-bananapi-m2-plus.dtsi
+++ b/arch/arm/boot/dts/allwinner/sunxi-bananapi-m2-plus.dtsi
@@ -77,10 +77,10 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		sw4 {
+		switch-4 {
 			label = "power";
 			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
@@ -89,19 +89,19 @@
 	};
 
 	reg_gmac_3v3: gmac-3v3 {
-		      compatible = "regulator-fixed";
-		      regulator-name = "gmac-3v3";
-		      regulator-min-microvolt = <3300000>;
-		      regulator-max-microvolt = <3300000>;
-		      startup-delay-us = <100000>;
-		      enable-active-high;
-		      gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+		compatible = "regulator-fixed";
+		regulator-name = "gmac-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <100000>;
+		enable-active-high;
+		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
 	};
 
-	wifi_pwrseq: wifi_pwrseq {
+	wifi_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "ext_clock";
 	};
 };
@@ -221,7 +221,7 @@
 	bluetooth {
 		compatible = "brcm,bcm43438-bt";
 		max-speed = <1500000>;
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "lpo";
 		vbat-supply = <&reg_vcc3v3>;
 		vddio-supply = <&reg_vcc3v3>;
diff --git a/arch/arm/boot/dts/sunxi-common-regulators.dtsi b/arch/arm/boot/dts/allwinner/sunxi-common-regulators.dtsi
index d8e5826fb3de..d8e5826fb3de 100644
--- a/arch/arm/boot/dts/sunxi-common-regulators.dtsi
+++ b/arch/arm/boot/dts/allwinner/sunxi-common-regulators.dtsi
diff --git a/arch/arm/boot/dts/allwinner/sunxi-d1s-t113-mangopi-mq-r.dtsi b/arch/arm/boot/dts/allwinner/sunxi-d1s-t113-mangopi-mq-r.dtsi
new file mode 100644
index 000000000000..a415c4a78a70
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sunxi-d1s-t113-mangopi-mq-r.dtsi
@@ -0,0 +1,126 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2022 Arm Ltd.
+/*
+ * Common peripherals and configurations for MangoPi MQ-R boards.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	aliases {
+		serial3 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial3:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&pio 3 22 GPIO_ACTIVE_LOW>; /* PD22 */
+		};
+	};
+
+	/* board wide 5V supply directly from the USB-C socket */
+	reg_vcc5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	/* SY8008 DC/DC regulator on the board */
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_vcc5v>;
+	};
+
+	/* SY8008 DC/DC regulator on the board, also supplying VDD-SYS */
+	reg_vcc_core: regulator-core {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-core";
+		regulator-min-microvolt = <880000>;
+		regulator-max-microvolt = <880000>;
+		vin-supply = <&reg_vcc5v>;
+	};
+
+	/* XC6206 LDO on the board */
+	reg_avdd2v8: regulator-avdd {
+		compatible = "regulator-fixed";
+		regulator-name = "avdd2v8";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		vin-supply = <&reg_3v3>;
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pio 6 12 GPIO_ACTIVE_LOW>; /* PG12 */
+	};
+};
+
+&dcxo {
+	clock-frequency = <24000000>;
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&mmc0 {
+	pinctrl-0 = <&mmc0_pins>;
+	pinctrl-names = "default";
+	vmmc-supply = <&reg_3v3>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc1 {
+	pinctrl-0 = <&mmc1_pins>;
+	pinctrl-names = "default";
+	vmmc-supply = <&reg_3v3>;
+	non-removable;
+	bus-width = <4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&pio {
+	vcc-pb-supply = <&reg_3v3>;
+	vcc-pd-supply = <&reg_3v3>;
+	vcc-pe-supply = <&reg_avdd2v8>;
+	vcc-pf-supply = <&reg_3v3>;
+	vcc-pg-supply = <&reg_3v3>;
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pb_pins>;
+	status = "okay";
+};
+
+/* The USB-C socket has its CC pins pulled to GND, so is hardwired as a UFP. */
+&usb_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_vcc5v>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sunxi-h3-h5-emlid-neutis.dtsi b/arch/arm/boot/dts/allwinner/sunxi-h3-h5-emlid-neutis.dtsi
index fc67e30fe212..be5f5528a118 100644
--- a/arch/arm/boot/dts/sunxi-h3-h5-emlid-neutis.dtsi
+++ b/arch/arm/boot/dts/allwinner/sunxi-h3-h5-emlid-neutis.dtsi
@@ -18,11 +18,11 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	wifi_pwrseq: wifi_pwrseq {
+	wifi_pwrseq: pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&pio 2 7 GPIO_ACTIVE_LOW>; /* PC7 */
 		post-power-on-delay-ms = <200>;
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "ext_clock";
 	};
 };
@@ -124,7 +124,7 @@
 
 	bluetooth {
 		compatible = "brcm,bcm43438-bt";
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "lpo";
 		vbat-supply = <&reg_vcc3v3>;
 		vddio-supply = <&reg_vcc3v3>;
diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/allwinner/sunxi-h3-h5.dtsi
index d7e9f977f986..7df60515a903 100644
--- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi
+++ b/arch/arm/boot/dts/allwinner/sunxi-h3-h5.dtsi
@@ -40,6 +40,7 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
+#include <dt-bindings/clock/sun6i-rtc.h>
 #include <dt-bindings/clock/sun8i-de2.h>
 #include <dt-bindings/clock/sun8i-h3-ccu.h>
 #include <dt-bindings/clock/sun8i-r-ccu.h>
@@ -82,7 +83,7 @@
 		#size-cells = <1>;
 		ranges;
 
-		osc24M: osc24M_clk {
+		osc24M: osc24M-clk {
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <24000000>;
@@ -90,7 +91,7 @@
 			clock-output-names = "osc24M";
 		};
 
-		osc32k: osc32k_clk {
+		osc32k: osc32k-clk {
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <32768>;
@@ -301,6 +302,8 @@
 			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_EHCI0>, <&ccu CLK_BUS_OHCI0>;
 			resets = <&ccu RST_BUS_EHCI0>, <&ccu RST_BUS_OHCI0>;
+			phys = <&usbphy 0>;
+			phy-names = "usb";
 			status = "disabled";
 		};
 
@@ -311,6 +314,8 @@
 			clocks = <&ccu CLK_BUS_EHCI0>, <&ccu CLK_BUS_OHCI0>,
 				 <&ccu CLK_USB_OHCI0>;
 			resets = <&ccu RST_BUS_EHCI0>, <&ccu RST_BUS_OHCI0>;
+			phys = <&usbphy 0>;
+			phy-names = "usb";
 			status = "disabled";
 		};
 
@@ -386,7 +391,7 @@
 		ccu: clock@1c20000 {
 			/* compatible is in per SoC .dtsi file */
 			reg = <0x01c20000 0x400>;
-			clocks = <&osc24M>, <&rtc 0>;
+			clocks = <&osc24M>, <&rtc CLK_OSC32K>;
 			clock-names = "hosc", "losc";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -398,7 +403,8 @@
 			interrupt-parent = <&r_intc>;
 			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&rtc 0>;
+			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>,
+				 <&rtc CLK_OSC32K>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			#gpio-cells = <3>;
@@ -704,7 +710,7 @@
 			clocks = <&ccu CLK_BUS_UART0>;
 			resets = <&ccu RST_BUS_UART0>;
 			dmas = <&dma 6>, <&dma 6>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -717,7 +723,7 @@
 			clocks = <&ccu CLK_BUS_UART1>;
 			resets = <&ccu RST_BUS_UART1>;
 			dmas = <&dma 7>, <&dma 7>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -730,7 +736,7 @@
 			clocks = <&ccu CLK_BUS_UART2>;
 			resets = <&ccu RST_BUS_UART2>;
 			dmas = <&dma 8>, <&dma 8>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -743,7 +749,7 @@
 			clocks = <&ccu CLK_BUS_UART3>;
 			resets = <&ccu RST_BUS_UART3>;
 			dmas = <&dma 9>, <&dma 9>;
-			dma-names = "rx", "tx";
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -818,7 +824,7 @@
 			reg-io-width = <1>;
 			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_DDC>,
-				 <&ccu CLK_HDMI>, <&rtc 0>;
+				 <&ccu CLK_HDMI>, <&rtc CLK_OSC32K>;
 			clock-names = "iahb", "isfr", "tmds", "cec";
 			resets = <&ccu RST_BUS_HDMI1>;
 			reset-names = "ctrl";
@@ -878,7 +884,7 @@
 		r_ccu: clock@1f01400 {
 			compatible = "allwinner,sun8i-h3-r-ccu";
 			reg = <0x01f01400 0x100>;
-			clocks = <&osc24M>, <&rtc 0>, <&rtc 2>,
+			clocks = <&osc24M>, <&rtc CLK_OSC32K>, <&rtc CLK_IOSC>,
 				 <&ccu CLK_PLL_PERIPH0>;
 			clock-names = "hosc", "losc", "iosc", "pll-periph";
 			#clock-cells = <1>;
@@ -931,7 +937,8 @@
 			reg = <0x01f02c00 0x400>;
 			interrupt-parent = <&r_intc>;
 			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&r_ccu CLK_APB0_PIO>, <&osc24M>, <&rtc 0>;
+			clocks = <&r_ccu CLK_APB0_PIO>, <&osc24M>,
+				 <&rtc CLK_OSC32K>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			#gpio-cells = <3>;
diff --git a/arch/arm/boot/dts/sunxi-itead-core-common.dtsi b/arch/arm/boot/dts/allwinner/sunxi-itead-core-common.dtsi
index 0d002f83a259..0d002f83a259 100644
--- a/arch/arm/boot/dts/sunxi-itead-core-common.dtsi
+++ b/arch/arm/boot/dts/allwinner/sunxi-itead-core-common.dtsi
diff --git a/arch/arm/boot/dts/sunxi-libretech-all-h3-cc.dtsi b/arch/arm/boot/dts/allwinner/sunxi-libretech-all-h3-cc.dtsi
index 9e14fe5fdcde..89731bb34c6b 100644
--- a/arch/arm/boot/dts/sunxi-libretech-all-h3-cc.dtsi
+++ b/arch/arm/boot/dts/allwinner/sunxi-libretech-all-h3-cc.dtsi
@@ -42,10 +42,10 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "power";
 			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
diff --git a/arch/arm/boot/dts/sunxi-libretech-all-h3-it.dtsi b/arch/arm/boot/dts/allwinner/sunxi-libretech-all-h3-it.dtsi
index 50d328c2a84d..50d328c2a84d 100644
--- a/arch/arm/boot/dts/sunxi-libretech-all-h3-it.dtsi
+++ b/arch/arm/boot/dts/allwinner/sunxi-libretech-all-h3-it.dtsi
diff --git a/arch/arm/boot/dts/sunxi-reference-design-tablet.dtsi b/arch/arm/boot/dts/allwinner/sunxi-reference-design-tablet.dtsi
index 117198c52e1f..117198c52e1f 100644
--- a/arch/arm/boot/dts/sunxi-reference-design-tablet.dtsi
+++ b/arch/arm/boot/dts/allwinner/sunxi-reference-design-tablet.dtsi
diff --git a/arch/arm/boot/dts/alphascale/Makefile b/arch/arm/boot/dts/alphascale/Makefile
new file mode 100644
index 000000000000..8d1314fc79d0
--- /dev/null
+++ b/arch/arm/boot/dts/alphascale/Makefile
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_MACH_ASM9260) += \
+	alphascale-asm9260-devkit.dtb
+dtb-$(CONFIG_MACH_ASM9260) += \
+	alphascale-asm9260-devkit.dtb
diff --git a/arch/arm/boot/dts/alphascale-asm9260-devkit.dts b/arch/arm/boot/dts/alphascale/alphascale-asm9260-devkit.dts
index c77e2c902fb6..c77e2c902fb6 100644
--- a/arch/arm/boot/dts/alphascale-asm9260-devkit.dts
+++ b/arch/arm/boot/dts/alphascale/alphascale-asm9260-devkit.dts
diff --git a/arch/arm/boot/dts/alphascale-asm9260.dtsi b/arch/arm/boot/dts/alphascale/alphascale-asm9260.dtsi
index 2ce6038536fd..2ce6038536fd 100644
--- a/arch/arm/boot/dts/alphascale-asm9260.dtsi
+++ b/arch/arm/boot/dts/alphascale/alphascale-asm9260.dtsi
diff --git a/arch/arm/boot/dts/am335x-netcan-plus-1xx.dts b/arch/arm/boot/dts/am335x-netcan-plus-1xx.dts
deleted file mode 100644
index 57e756b0f192..000000000000
--- a/arch/arm/boot/dts/am335x-netcan-plus-1xx.dts
+++ /dev/null
@@ -1,87 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
- */
-
-/*
- * VScom OnRISC
- * http://www.vscom.de
- */
-
-/dts-v1/;
-
-#include "am335x-baltos.dtsi"
-#include "am335x-baltos-leds.dtsi"
-
-/ {
-	model = "NetCAN";
-
-	leds {
-		pinctrl-names = "default";
-		pinctrl-0 = <&user_leds_s0>;
-
-		compatible = "gpio-leds";
-
-		led@1 {
-			label = "can_data";
-			linux,default-trigger = "netdev";
-			gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
-			default-state = "off";
-		};
-		led@2 {
-			label = "can_error";
-			gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
-			default-state = "off";
-		};
-	};
-};
-
-&am33xx_pinmux {
-	user_leds_s0: user_leds_s0 {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* CAN Data LED */
-			AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* CAN Error LED */
-		>;
-	};
-
-	dcan1_pins: pinmux_dcan1_pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_OUTPUT, MUX_MODE2)	/* CAN TX */
-			AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_INPUT, MUX_MODE2)	/* CAN RX */
-		>;
-	};
-};
-
-&usb0_phy {
-	status = "okay";
-};
-
-&usb0 {
-	status = "okay";
-	dr_mode = "host";
-};
-
-&davinci_mdio_sw {
-	phy0: ethernet-phy@0 {
-		reg = <1>;
-	};
-};
-
-&cpsw_port1 {
-	phy-mode = "rmii";
-	ti,dual-emac-pvid = <1>;
-	phy-handle = <&phy0>;
-};
-
-&cpsw_port2 {
-	phy-mode = "rgmii-id";
-	ti,dual-emac-pvid = <2>;
-	phy-handle = <&phy1>;
-};
-
-&dcan1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&dcan1_pins>;
-
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/am335x-netcom-plus-8xx.dts b/arch/arm/boot/dts/am335x-netcom-plus-8xx.dts
deleted file mode 100644
index 96dffd3ffd85..000000000000
--- a/arch/arm/boot/dts/am335x-netcom-plus-8xx.dts
+++ /dev/null
@@ -1,115 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
- */
-
-/*
- * VScom OnRISC
- * http://www.vscom.de
- */
-
-/dts-v1/;
-
-#include "am335x-baltos.dtsi"
-
-/ {
-	model = "NetCom Plus";
-};
-
-&am33xx_pinmux {
-	pinctrl-names = "default";
-	pinctrl-0 = <&dip_switches>;
-
-	dip_switches: pinmux_dip_switches {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_GPMC_AD12, PIN_INPUT_PULLDOWN, MUX_MODE7)
-			AM33XX_PADCONF(AM335X_PIN_GPMC_AD13, PIN_INPUT_PULLDOWN, MUX_MODE7)
-			AM33XX_PADCONF(AM335X_PIN_GPMC_AD14, PIN_INPUT_PULLDOWN, MUX_MODE7)
-			AM33XX_PADCONF(AM335X_PIN_GPMC_AD15, PIN_INPUT_PULLDOWN, MUX_MODE7)
-		>;
-	};
-
-	tca6416_pins: pinmux_tca6416_pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR1, PIN_INPUT_PULLUP, MUX_MODE7)
-		>;
-	};
-
-	i2c2_pins: pinmux_i2c2_pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT_PULLDOWN, MUX_MODE3)
-			AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_INPUT_PULLDOWN, MUX_MODE3)
-		>;
-	};
-};
-
-&usb0_phy {
-	status = "okay";
-};
-
-&usb1_phy {
-	status = "okay";
-};
-
-&usb0 {
-	status = "okay";
-	dr_mode = "host";
-};
-
-&usb1 {
-	status = "okay";
-	dr_mode = "host";
-};
-
-&i2c1 {
-	tca6416a: gpio@20 {
-		compatible = "ti,tca6416";
-		reg = <0x20>;
-		gpio-controller;
-		#gpio-cells = <2>;
-		interrupt-parent = <&gpio0>;
-		interrupts = <20 IRQ_TYPE_EDGE_RISING>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&tca6416_pins>;
-	};
-};
-
-&i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins>;
-
-	status = "okay";
-	clock-frequency = <400000>;
-
-	tca6416b: gpio@20 {
-		compatible = "ti,tca6416";
-		reg = <0x20>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	tca6416c: gpio@21 {
-		compatible = "ti,tca6416";
-		reg = <0x21>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-};
-
-&davinci_mdio_sw {
-	phy0: ethernet-phy@0 {
-		reg = <1>;
-	};
-};
-
-&cpsw_port1 {
-	phy-mode = "rmii";
-	ti,dual-emac-pvid = <1>;
-	phy-handle = <&phy0>;
-};
-
-&cpsw_port2 {
-	phy-mode = "rgmii-id";
-	ti,dual-emac-pvid = <2>;
-	phy-handle = <&phy1>;
-};
diff --git a/arch/arm/boot/dts/amazon/Makefile b/arch/arm/boot/dts/amazon/Makefile
new file mode 100644
index 000000000000..58af5c4846ef
--- /dev/null
+++ b/arch/arm/boot/dts/amazon/Makefile
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_ALPINE) += \
+	alpine-db.dtb
+dtb-$(CONFIG_ARCH_ALPINE) += \
+	alpine-db.dtb
diff --git a/arch/arm/boot/dts/alpine-db.dts b/arch/arm/boot/dts/amazon/alpine-db.dts
index dfb5a0802273..dfb5a0802273 100644
--- a/arch/arm/boot/dts/alpine-db.dts
+++ b/arch/arm/boot/dts/amazon/alpine-db.dts
diff --git a/arch/arm/boot/dts/alpine.dtsi b/arch/arm/boot/dts/amazon/alpine.dtsi
index 3b0675a1c460..90bd12feac01 100644
--- a/arch/arm/boot/dts/alpine.dtsi
+++ b/arch/arm/boot/dts/amazon/alpine.dtsi
@@ -126,7 +126,7 @@
 				     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
-		uart0: uart@fd883000 {
+		uart0: serial@fd883000 {
 			compatible = "ns16550a";
 			reg = <0x0 0xfd883000 0x0 0x1000>;
 			clock-frequency = <375000000>;
@@ -135,7 +135,7 @@
 			reg-io-width = <4>;
 		};
 
-		uart1: uart@fd884000 {
+		uart1: serial@fd884000 {
 			compatible = "ns16550a";
 			reg = <0x0 0xfd884000 0x0 0x1000>;
 			clock-frequency = <375000000>;
@@ -154,7 +154,7 @@
 			reg = <0x0 0xfbc00000 0x0 0x100000>;
 			interrupt-map-mask = <0xf800 0 0 7>;
 			/* Add legacy interrupts for SATA devices only */
-			interrupt-map =	<0x4000 0 0 1 &gic 0 43 4>,
+			interrupt-map = <0x4000 0 0 1 &gic 0 43 4>,
 					<0x4800 0 0 1 &gic 0 44 4>;
 
 			/* 32 bit non prefetchable memory space */
@@ -167,7 +167,6 @@
 		msix: msix@fbe00000 {
 			compatible = "al,alpine-msix";
 			reg = <0x0 0xfbe00000 0x0 0x100000>;
-			interrupt-controller;
 			msi-controller;
 			al,msi-base-spi = <96>;
 			al,msi-num-spis = <64>;
diff --git a/arch/arm/boot/dts/amlogic/Makefile b/arch/arm/boot/dts/amlogic/Makefile
new file mode 100644
index 000000000000..3c8a1e88b386
--- /dev/null
+++ b/arch/arm/boot/dts/amlogic/Makefile
@@ -0,0 +1,8 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_MACH_MESON8) += \
+	meson8-minix-neo-x8.dtb \
+	meson8-fernsehfee3.dtb \
+	meson8b-ec100.dtb \
+	meson8b-mxq.dtb \
+	meson8b-odroidc1.dtb \
+	meson8m2-mxiii-plus.dtb
diff --git a/arch/arm/boot/dts/meson.dtsi b/arch/arm/boot/dts/amlogic/meson.dtsi
index 26eaba3fa96f..28ec2c821cdc 100644
--- a/arch/arm/boot/dts/meson.dtsi
+++ b/arch/arm/boot/dts/amlogic/meson.dtsi
@@ -23,7 +23,7 @@
 		#size-cells = <1>;
 		ranges;
 
-		cbus: cbus@c1100000 {
+		cbus: bus@c1100000 {
 			compatible = "simple-bus";
 			reg = <0xc1100000 0x200000>;
 			#address-cells = <1>;
@@ -206,7 +206,7 @@
 			};
 		};
 
-		aobus: aobus@c8100000 {
+		aobus: bus@c8100000 {
 			compatible = "simple-bus";
 			reg = <0xc8100000 0x100000>;
 			#address-cells = <1>;
@@ -214,14 +214,14 @@
 			ranges = <0x0 0xc8100000 0x100000>;
 
 			ao_arc_rproc: remoteproc@1c {
-				compatible= "amlogic,meson-mx-ao-arc";
+				compatible = "amlogic,meson-mx-ao-arc";
 				reg = <0x1c 0x8>, <0x38 0x8>;
 				reg-names = "remap", "cpu";
 				status = "disabled";
 			};
 
 			ir_receiver: ir-receiver@480 {
-				compatible= "amlogic,meson6-ir";
+				compatible = "amlogic,meson6-ir";
 				reg = <0x480 0x20>;
 				interrupts = <GIC_SPI 15 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
@@ -255,8 +255,6 @@
 
 		usb0: usb@c9040000 {
 			compatible = "snps,dwc2";
-			#address-cells = <1>;
-			#size-cells = <0>;
 			reg = <0xc9040000 0x40000>;
 			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
 			phys = <&usb0_phy>;
@@ -270,8 +268,6 @@
 
 		usb1: usb@c90c0000 {
 			compatible = "snps,dwc2";
-			#address-cells = <1>;
-			#size-cells = <0>;
 			reg = <0xc90c0000 0x40000>;
 			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
 			phys = <&usb1_phy>;
@@ -302,7 +298,7 @@
 			reg = <0xd9040000 0x10000>;
 		};
 
-		secbus: secbus@da000000 {
+		secbus: bus@da000000 {
 			compatible = "simple-bus";
 			reg = <0xda000000 0x6000>;
 			#address-cells = <1>;
diff --git a/arch/arm/boot/dts/amlogic/meson8-fernsehfee3.dts b/arch/arm/boot/dts/amlogic/meson8-fernsehfee3.dts
new file mode 100644
index 000000000000..4e52447d51bd
--- /dev/null
+++ b/arch/arm/boot/dts/amlogic/meson8-fernsehfee3.dts
@@ -0,0 +1,306 @@
+// SPDX-License-Identifier: GPL-2.0-only OR MIT
+// Copyright (C) 2025 J. Neuschäfer <j.ne@posteo.net>
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/leds/common.h>
+
+#include "meson8.dtsi"
+
+/ {
+	model = "Fernsehfee 3.0";
+	compatible = "tcu,fernsehfee3", "amlogic,meson8";
+
+	aliases {
+		serial0 = &uart_AO;
+		gpiochip0 = &gpio;
+		gpiochip1 = &gpio_ao;
+		i2c0 = &i2c_AO;
+		i2c1 = &i2c_B;
+		mmc0 = &sdhc;
+		mmc1 = &sdio;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x40000000>;  /* 1 GiB */
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys-polled";
+		poll-interval = <100>;
+
+		power-button {
+			label = "Power button";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			/*
+			 * The power LED can be turned red, otherwise it is green.
+			 */
+			gpios = <&gpio_ao GPIO_TEST_N GPIO_ACTIVE_LOW>;
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_RED>;
+		};
+	};
+
+	vcc_5v: regulator-5v {
+		/* 5V rail, always on as long as the system is running */
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	vcc_3v3: regulator-3v3 {
+		/* Chipown AP2420 step-down converter */
+		compatible = "regulator-fixed";
+		regulator-name = "3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_5v>;
+	};
+
+	wifi_3v3: regulator-wifi {
+		compatible = "regulator-fixed";
+		regulator-name = "3.3V-WIFI";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_3v3>;
+		gpio = <&gpio GPIOX_11 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&vcck>;
+};
+
+&ethmac {
+	status = "okay";
+	pinctrl-0 = <&eth_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&eth_phy0>;
+	phy-mode = "rmii";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		eth_phy0: ethernet-phy@0 {
+			/* IC Plus IP101A (0x02430c54) */
+			reg = <0>;
+
+			reset-assert-us = <10000>;
+			reset-deassert-us = <10000>;
+			reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&i2c_AO {
+	status = "okay";
+	pinctrl-0 = <&i2c_ao_pins>;
+	pinctrl-names = "default";
+
+	pmic@32 {
+		compatible = "ricoh,rn5t618";
+		reg = <0x32>;
+		system-power-controller;
+
+		regulators {
+			vcck: DCDC1 {
+				regulator-name = "VCCK";
+				regulator-min-microvolt = <825000>;
+				regulator-max-microvolt = <1150000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vddee: DCDC2 {
+				/* the output is also used as VDDAO */
+				regulator-name = "VDD_EE";
+				regulator-min-microvolt = <950000>;
+				regulator-max-microvolt = <1150000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			DCDC3 {
+				regulator-name = "VDD_DDR";
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			LDO1 {
+				regulator-name = "VDDIO_AO28";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			LDO2 {
+				regulator-name = "VDDIO_AO18";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vcc1v8_usb: LDO3 {
+				regulator-name = "VCC1V8_USB";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+			};
+
+			LDO4 {
+				/* This one appears to be unused */
+				regulator-name = "VCC2V8";
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <2850000>;
+			};
+
+			LDO5 {
+				regulator-name = "AVDD1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			LDORTC1 {
+				regulator-name = "VDD_LDO";
+				regulator-min-microvolt = <2700000>;
+				regulator-max-microvolt = <2700000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			LDORTC2 {
+				regulator-name = "RTC_0V9";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	eeprom@50 {
+		/* Fairchild FM24C08A */
+		compatible = "atmel,24c08";
+		reg = <0x50>;
+		pagesize = <16>;
+		wp-gpios = <&gpio GPIOH_3 GPIO_ACTIVE_HIGH>;
+		num-addresses = <4>;
+	};
+};
+
+&i2c_B {
+	status = "okay";
+	pinctrl-0 = <&i2c_b_pins>;
+	pinctrl-names = "default";
+
+	/* TODO: SiI9293 HDMI receiver @ 0x39 */
+};
+
+&mali {
+	mali-supply = <&vddee>;
+};
+
+&sdhc {
+	status = "okay";
+	pinctrl-0 = <&sdxc_c_pins>;
+	pinctrl-names = "default";
+
+	/* eMMC */
+	bus-width = <8>;
+	max-frequency = <100000000>;
+
+	disable-wp;
+	cap-mmc-highspeed;
+	mmc-hs200-1_8v;
+	no-sdio;
+
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_3v3>;
+};
+
+&sdio {
+	status = "okay";
+	pinctrl-0 = <&sd_b_pins>;
+
+	/* SD card */
+	slot@1 {
+		compatible = "mmc-slot";
+		reg = <1>;
+		status = "okay";
+
+		bus-width = <4>;
+		cap-mmc-highspeed;
+		cap-sd-highspeed;
+		disable-wp;
+
+		cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
+
+		vmmc-supply = <&vcc_3v3>;
+	};
+};
+
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb0_phy {
+	status = "okay";
+	phy-supply = <&vcc1v8_usb>;
+};
+
+&usb1 {
+	status = "okay";
+	dr_mode = "host";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	wifi: wifi@1 {
+		/* Realtek RTL8188 2.4GHz WiFi module */
+		compatible = "usbbda,179";
+		reg = <1>;
+		vdd-supply = <&wifi_3v3>;
+	};
+};
+
+&usb1_phy {
+	status = "okay";
+	phy-supply = <&vcc1v8_usb>;
+};
+
+&ir_receiver {
+	status = "okay";
+	pinctrl-0 = <&ir_recv_pins>;
+	pinctrl-names = "default";
+};
diff --git a/arch/arm/boot/dts/meson8-minix-neo-x8.dts b/arch/arm/boot/dts/amlogic/meson8-minix-neo-x8.dts
index 61ec929ab86e..62987eadc747 100644
--- a/arch/arm/boot/dts/meson8-minix-neo-x8.dts
+++ b/arch/arm/boot/dts/amlogic/meson8-minix-neo-x8.dts
@@ -19,7 +19,7 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory {
+	memory@40000000 {
 		device_type = "memory";
 		reg = <0x40000000 0x80000000>;
 	};
@@ -27,7 +27,7 @@
 	gpio-leds {
 		compatible = "gpio-leds";
 
-		blue {
+		led-blue {
 			label = "x8:blue:power";
 			gpios = <&gpio_ao GPIO_TEST_N GPIO_ACTIVE_HIGH>;
 		};
@@ -65,7 +65,7 @@
 	pinctrl-0 = <&spi_nor_pins>;
 	pinctrl-names = "default";
 
-	spi-flash@0 {
+	flash@0 {
 		compatible = "mxicy,mx25l1606e";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -93,5 +93,6 @@
 &ethmac {
 	status = "okay";
 	pinctrl-0 = <&eth_pins>;
-	pnictrl-names = "default";
+	pinctrl-names = "default";
+	phy-mode = "rmii";
 };
diff --git a/arch/arm/boot/dts/meson8.dtsi b/arch/arm/boot/dts/amlogic/meson8.dtsi
index 9997a5d0333a..a609b5a0fda4 100644
--- a/arch/arm/boot/dts/meson8.dtsi
+++ b/arch/arm/boot/dts/amlogic/meson8.dtsi
@@ -133,7 +133,7 @@
 		};
 	};
 
-	gpu_opp_table: gpu-opp-table {
+	gpu_opp_table: opp-table-gpu {
 		compatible = "operating-points-v2";
 
 		opp-182142857 {
@@ -196,7 +196,7 @@
 	};
 
 	thermal-zones {
-		soc {
+		soc-thermal {
 			polling-delay-passive = <250>; /* milliseconds */
 			polling-delay = <1000>; /* milliseconds */
 			thermal-sensors = <&thermal_sensor>;
@@ -346,17 +346,16 @@
 		reg = <0xe0 0x18>;
 	};
 
-	pinctrl_aobus: pinctrl@84 {
+	pinctrl_aobus: pinctrl@14 {
 		compatible = "amlogic,meson8-aobus-pinctrl";
-		reg = <0x84 0xc>;
 		#address-cells = <1>;
 		#size-cells = <1>;
-		ranges;
+		ranges = <0x0 0x14 0x1c>;
 
-		gpio_ao: ao-bank@14 {
-			reg = <0x14 0x4>,
-			      <0x2c 0x4>,
-			      <0x24 0x8>;
+		gpio_ao: bank@0 {
+			reg = <0x0 0x4>,
+			      <0x18 0x4>,
+			      <0x10 0x8>;
 			reg-names = "mux", "pull", "gpio";
 			gpio-controller;
 			#gpio-cells = <2>;
@@ -399,7 +398,7 @@
 			mux {
 				groups = "uart_tx_ao_a", "uart_rx_ao_a";
 				function = "uart_ao";
-				bias-disable;
+				bias-pull-up;
 			};
 		};
 
@@ -430,7 +429,7 @@
 };
 
 &ao_arc_rproc {
-	compatible= "amlogic,meson8-ao-arc", "amlogic,meson-mx-ao-arc";
+	compatible = "amlogic,meson8-ao-arc", "amlogic,meson-mx-ao-arc";
 	amlogic,secbus2 = <&secbus2>;
 	sram = <&ao_arc_sram>;
 	resets = <&reset RESET_MEDIA_CPU>;
@@ -450,7 +449,11 @@
 	};
 
 	pwm_ef: pwm@86c0 {
-		compatible = "amlogic,meson8-pwm", "amlogic,meson8b-pwm";
+		compatible = "amlogic,meson8-pwm-v2";
+		clocks = <&xtal>,
+			 <0>, /* unknown/untested, the datasheet calls it "Video PLL" */
+			 <&clkc CLKID_FCLK_DIV4>,
+			 <&clkc CLKID_FCLK_DIV3>;
 		reg = <0x86c0 0x10>;
 		#pwm-cells = <3>;
 		status = "disabled";
@@ -461,24 +464,31 @@
 		reg = <0x8758 0x1c>;
 	};
 
-	pinctrl_cbus: pinctrl@9880 {
+	pinctrl_cbus: pinctrl@8030 {
 		compatible = "amlogic,meson8-cbus-pinctrl";
-		reg = <0x9880 0x10>;
 		#address-cells = <1>;
 		#size-cells = <1>;
-		ranges;
+		ranges = <0x0 0x8030 0x108>;
 
-		gpio: banks@80b0 {
-			reg = <0x80b0 0x28>,
-			      <0x80e8 0x18>,
-			      <0x8120 0x18>,
-			      <0x8030 0x30>;
+		gpio: bank@80 {
+			reg = <0x80 0x28>,
+			      <0xb8 0x18>,
+			      <0xf0 0x18>,
+			      <0x00 0x30>;
 			reg-names = "mux", "pull", "pull-enable", "gpio";
 			gpio-controller;
 			#gpio-cells = <2>;
 			gpio-ranges = <&pinctrl_cbus 0 0 120>;
 		};
 
+		i2c_b_pins: i2c-b {
+			mux {
+				groups = "i2c_sda_b", "i2c_sck_b";
+				function = "i2c_b";
+				bias-disable;
+			};
+		};
+
 		sd_a_pins: sd-a {
 			mux {
 				groups = "sd_d0_a", "sd_d1_a", "sd_d2_a",
@@ -506,6 +516,15 @@
 			};
 		};
 
+		sdxc_a_pins: sdxc-a {
+			mux {
+				groups = "sdxc_d0_a", "sdxc_d13_a",
+					 "sdxc_clk_a", "sdxc_cmd_a";
+				function = "sdxc_a";
+				bias-pull-up;
+			};
+		};
+
 		sdxc_b_pins: sdxc-b {
 			mux {
 				groups = "sdxc_d0_b", "sdxc_d13_b",
@@ -515,6 +534,16 @@
 			};
 		};
 
+		sdxc_c_pins: sdxc-c {
+			mux {
+				groups = "sdxc_d0_c", "sdxc_d13_c",
+					"sdxc_clk_c", "sdxc_cmd_c",
+					"sdxc_d47_c";
+				function = "sdxc_c";
+				bias-pull-up;
+			};
+		};
+
 		spdif_out_pins: spdif-out {
 			mux {
 				groups = "spdif_out";
@@ -556,7 +585,7 @@
 				groups = "uart_tx_a1",
 				       "uart_rx_a1";
 				function = "uart_a";
-				bias-disable;
+				bias-pull-up;
 			};
 		};
 
@@ -568,11 +597,19 @@
 				bias-disable;
 			};
 		};
+
+		xtal_32k_out_pins: xtal-32k-out {
+			mux {
+				groups = "xtal_32k_out";
+				function = "xtal";
+				bias-disable;
+			};
+		};
 	};
 };
 
 &ahb_sram {
-	ao_arc_sram: ao-arc-sram@0 {
+	ao_arc_sram: aoarc-sram@0 {
 		compatible = "amlogic,meson8-ao-arc-sram";
 		reg = <0x0 0x8000>;
 		pool;
@@ -628,7 +665,6 @@
 };
 
 &hwrng {
-	compatible = "amlogic,meson8-rng", "amlogic,meson-rng";
 	clocks = <&clkc CLKID_RNG0>;
 	clock-names = "core";
 };
@@ -651,6 +687,9 @@
 	arm,filter-ranges = <0x100000 0xc0000000>;
 	prefetch-data = <1>;
 	prefetch-instr = <1>;
+	arm,prefetch-offset = <7>;
+	arm,double-linefill = <1>;
+	arm,prefetch-drop = <1>;
 	arm,shared-override;
 };
 
@@ -682,11 +721,19 @@
 };
 
 &pwm_ab {
-	compatible = "amlogic,meson8-pwm", "amlogic,meson8b-pwm";
+	compatible = "amlogic,meson8-pwm-v2";
+	clocks = <&xtal>,
+		 <0>, /* unknown/untested, the datasheet calls it "Video PLL" */
+		 <&clkc CLKID_FCLK_DIV4>,
+		 <&clkc CLKID_FCLK_DIV3>;
 };
 
 &pwm_cd {
-	compatible = "amlogic,meson8-pwm", "amlogic,meson8b-pwm";
+	compatible = "amlogic,meson8-pwm-v2";
+	clocks = <&xtal>,
+		 <0>, /* unknown/untested, the datasheet calls it "Video PLL" */
+		 <&clkc CLKID_FCLK_DIV4>,
+		 <&clkc CLKID_FCLK_DIV3>;
 };
 
 &rtc {
@@ -749,13 +796,13 @@
 
 &uart_B {
 	compatible = "amlogic,meson8-uart";
-	clocks = <&xtal>, <&clkc CLKID_UART0>, <&clkc CLKID_CLK81>;
+	clocks = <&xtal>, <&clkc CLKID_UART1>, <&clkc CLKID_CLK81>;
 	clock-names = "xtal", "pclk", "baud";
 };
 
 &uart_C {
 	compatible = "amlogic,meson8-uart";
-	clocks = <&xtal>, <&clkc CLKID_UART0>, <&clkc CLKID_CLK81>;
+	clocks = <&xtal>, <&clkc CLKID_UART2>, <&clkc CLKID_CLK81>;
 	clock-names = "xtal", "pclk", "baud";
 };
 
diff --git a/arch/arm/boot/dts/meson8b-ec100.dts b/arch/arm/boot/dts/amlogic/meson8b-ec100.dts
index 77d4beeb8010..236999548094 100644
--- a/arch/arm/boot/dts/meson8b-ec100.dts
+++ b/arch/arm/boot/dts/amlogic/meson8b-ec100.dts
@@ -22,7 +22,7 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory {
+	memory@40000000 {
 		device_type = "memory";
 		reg = <0x40000000 0x40000000>;
 	};
@@ -34,8 +34,6 @@
 
 	gpio-keys {
 		compatible = "gpio-keys-polled";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		poll-interval = <100>;
 
 		pal-switch {
@@ -73,7 +71,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		power {
+		led-power {
 			label = "ec100:red:power";
 			/*
 			 * Needs to go LOW (together with the poweroff GPIO)
@@ -100,6 +98,10 @@
 		compatible = "amlogic,gx-sound-card";
 		model = "M8B-EC100";
 
+		clocks = <&clkc CLKID_MPLL0>,
+			 <&clkc CLKID_MPLL1>,
+			 <&clkc CLKID_MPLL2>;
+
 		assigned-clocks = <&clkc CLKID_MPLL0>,
 				  <&clkc CLKID_MPLL1>,
 				  <&clkc CLKID_MPLL2>;
@@ -429,7 +431,7 @@
 			  "NAND_CS1 (EMMC)", "NAND_CS2 iNAND_RS1 (EMMC)",
 			  "NAND_nR/B iNAND_CMD (EMMC)", "NAND_ALE (EMMC)",
 			  "NAND_CLE (EMMC)", "nRE_S1 NAND_nRE (EMMC)",
-			  "nWE_S1 NAND_nWE (EMMC)",  "", "", "SPI_CS",
+			  "nWE_S1 NAND_nWE (EMMC)",  "", "", "", "SPI_CS",
 			  /* Bank DIF */
 			  "RMII_RXD1", "RMII_RXD0", "RMII_CRS_DV",
 			  "RMII_50M_IN", "GPIODIF_4", "GPIODIF_5",
@@ -441,8 +443,6 @@
 	status = "okay";
 	pinctrl-0 = <&pwm_c1_pins>, <&pwm_d_pins>;
 	pinctrl-names = "default";
-	clocks = <&xtal>, <&xtal>;
-	clock-names = "clkin0", "clkin1";
 };
 
 &rtc {
diff --git a/arch/arm/boot/dts/meson8b-mxq.dts b/arch/arm/boot/dts/amlogic/meson8b-mxq.dts
index 7adedd3258c3..0bca0b33eea2 100644
--- a/arch/arm/boot/dts/meson8b-mxq.dts
+++ b/arch/arm/boot/dts/amlogic/meson8b-mxq.dts
@@ -22,7 +22,7 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory {
+	memory@40000000 {
 		device_type = "memory";
 		reg = <0x40000000 0x40000000>;
 	};
@@ -162,8 +162,6 @@
 	status = "okay";
 	pinctrl-0 = <&pwm_c1_pins>, <&pwm_d_pins>;
 	pinctrl-names = "default";
-	clocks = <&xtal>, <&xtal>;
-	clock-names = "clkin0", "clkin1";
 };
 
 &uart_AO {
diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/amlogic/meson8b-odroidc1.dts
index 04356bc639fa..1cd2093202ca 100644
--- a/arch/arm/boot/dts/meson8b-odroidc1.dts
+++ b/arch/arm/boot/dts/amlogic/meson8b-odroidc1.dts
@@ -22,7 +22,7 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory {
+	memory@40000000 {
 		device_type = "memory";
 		reg = <0x40000000 0x40000000>;
 	};
@@ -34,7 +34,7 @@
 
 	leds {
 		compatible = "gpio-leds";
-		blue {
+		led-blue {
 			label = "c1:blue:alive";
 			gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "heartbeat";
@@ -281,19 +281,6 @@
 			  "J7 Header Pin 6", "J7 Header Pin 5",
 			  "J7 Header Pin 7", "HDMI_CEC",
 			  "SYS_LED", "", "";
-
-	/*
-	 * WARNING: The USB Hub on the Odroid-C1/C1+ needs a reset signal
-	 * to be turned high in order to be detected by the USB Controller.
-	 * This signal should be handled by a USB specific power sequence
-	 * in order to reset the Hub when USB bus is powered down.
-	 */
-	usb-hub {
-		gpio-hog;
-		gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "usb-hub-reset";
-	};
 };
 
 &ir_receiver {
@@ -360,8 +347,6 @@
 	status = "okay";
 	pinctrl-0 = <&pwm_c1_pins>, <&pwm_d_pins>;
 	pinctrl-names = "default";
-	clocks = <&xtal>, <&xtal>;
-	clock-names = "clkin0", "clkin1";
 };
 
 &rtc {
@@ -381,5 +366,16 @@
 };
 
 &usb1 {
+	dr_mode = "host";
+	#address-cells = <1>;
+	#size-cells = <0>;
 	status = "okay";
+
+	hub@1 {
+		/* Genesys Logic GL852G usb hub */
+		compatible = "usb5e3,610";
+		reg = <1>;
+		vdd-supply = <&p5v0>;
+		reset-gpios = <&gpio_ao GPIOAO_4 GPIO_ACTIVE_LOW>;
+	};
 };
diff --git a/arch/arm/boot/dts/meson8b.dtsi b/arch/arm/boot/dts/amlogic/meson8b.dtsi
index 94f1c03decce..2d77b9876bf4 100644
--- a/arch/arm/boot/dts/meson8b.dtsi
+++ b/arch/arm/boot/dts/amlogic/meson8b.dtsi
@@ -125,7 +125,7 @@
 		};
 	};
 
-	gpu_opp_table: gpu-opp-table {
+	gpu_opp_table: opp-table-gpu {
 		compatible = "operating-points-v2";
 
 		opp-255000000 {
@@ -173,7 +173,7 @@
 	};
 
 	thermal-zones {
-		soc {
+		soc-thermal {
 			polling-delay-passive = <250>; /* milliseconds */
 			polling-delay = <1000>; /* milliseconds */
 			thermal-sensors = <&thermal_sensor>;
@@ -308,17 +308,16 @@
 		reg = <0xe0 0x18>;
 	};
 
-	pinctrl_aobus: pinctrl@84 {
+	pinctrl_aobus: pinctrl@14 {
 		compatible = "amlogic,meson8b-aobus-pinctrl";
-		reg = <0x84 0xc>;
 		#address-cells = <1>;
 		#size-cells = <1>;
-		ranges;
+		ranges = <0x0 0x14 0x1c>;
 
-		gpio_ao: ao-bank@14 {
-			reg = <0x14 0x4>,
-				<0x2c 0x4>,
-				<0x24 0x8>;
+		gpio_ao: bank@0 {
+			reg = <0x0 0x4>,
+			      <0x18 0x4>,
+			      <0x10 0x8>;
 			reg-names = "mux", "pull", "gpio";
 			gpio-controller;
 			#gpio-cells = <2>;
@@ -369,7 +368,7 @@
 			mux {
 				groups = "uart_tx_ao_a", "uart_rx_ao_a";
 				function = "uart_ao";
-				bias-disable;
+				bias-pull-up;
 			};
 		};
 
@@ -384,7 +383,7 @@
 };
 
 &ao_arc_rproc {
-	compatible= "amlogic,meson8b-ao-arc", "amlogic,meson-mx-ao-arc";
+	compatible = "amlogic,meson8b-ao-arc", "amlogic,meson-mx-ao-arc";
 	amlogic,secbus2 = <&secbus2>;
 	sram = <&ao_arc_sram>;
 	resets = <&reset RESET_MEDIA_CPU>;
@@ -404,8 +403,12 @@
 	};
 
 	pwm_ef: pwm@86c0 {
-		compatible = "amlogic,meson8b-pwm";
+		compatible = "amlogic,meson8b-pwm-v2", "amlogic,meson8-pwm-v2";
 		reg = <0x86c0 0x10>;
+		clocks = <&xtal>,
+			 <0>, /* unknown/untested, the datasheet calls it "Video PLL" */
+			 <&clkc CLKID_FCLK_DIV4>,
+			 <&clkc CLKID_FCLK_DIV3>;
 		#pwm-cells = <3>;
 		status = "disabled";
 	};
@@ -415,18 +418,17 @@
 		reg = <0x8758 0x1c>;
 	};
 
-	pinctrl_cbus: pinctrl@9880 {
+	pinctrl_cbus: pinctrl@8030 {
 		compatible = "amlogic,meson8b-cbus-pinctrl";
-		reg = <0x9880 0x10>;
 		#address-cells = <1>;
 		#size-cells = <1>;
-		ranges;
+		ranges = <0x0 0x8030 0x108>;
 
-		gpio: banks@80b0 {
-			reg = <0x80b0 0x28>,
-				<0x80e8 0x18>,
-				<0x8120 0x18>,
-				<0x8030 0x38>;
+		gpio: bank@80 {
+			reg = <0x80 0x28>,
+			      <0xb8 0x18>,
+			      <0xf0 0x18>,
+			      <0x00 0x38>;
 			reg-names = "mux", "pull", "pull-enable", "gpio";
 			gpio-controller;
 			#gpio-cells = <2>;
@@ -519,7 +521,7 @@
 				groups = "uart_tx_b0",
 				       "uart_rx_b0";
 				function = "uart_b";
-				bias-disable;
+				bias-pull-up;
 			};
 		};
 
@@ -535,7 +537,7 @@
 };
 
 &ahb_sram {
-	ao_arc_sram: ao-arc-sram@0 {
+	ao_arc_sram: aoarc-sram@0 {
 		compatible = "amlogic,meson8b-ao-arc-sram";
 		reg = <0x0 0x8000>;
 		pool;
@@ -580,8 +582,8 @@
 };
 
 &gpio_intc {
-	compatible = "amlogic,meson-gpio-intc",
-		     "amlogic,meson8b-gpio-intc";
+	compatible = "amlogic,meson8b-gpio-intc",
+		     "amlogic,meson-gpio-intc";
 	status = "okay";
 };
 
@@ -620,7 +622,6 @@
 };
 
 &hwrng {
-	compatible = "amlogic,meson8b-rng", "amlogic,meson-rng";
 	clocks = <&clkc CLKID_RNG0>;
 	clock-names = "core";
 };
@@ -643,6 +644,9 @@
 	arm,filter-ranges = <0x100000 0xc0000000>;
 	prefetch-data = <1>;
 	prefetch-instr = <1>;
+	arm,prefetch-offset = <7>;
+	arm,double-linefill = <1>;
+	arm,prefetch-drop = <1>;
 	arm,shared-override;
 };
 
@@ -674,11 +678,19 @@
 };
 
 &pwm_ab {
-	compatible = "amlogic,meson8b-pwm";
+	compatible = "amlogic,meson8b-pwm-v2", "amlogic,meson8-pwm-v2";
+	clocks = <&xtal>,
+		 <0>, /* unknown/untested, the datasheet calls it "Video PLL" */
+		 <&clkc CLKID_FCLK_DIV4>,
+		 <&clkc CLKID_FCLK_DIV3>;
 };
 
 &pwm_cd {
-	compatible = "amlogic,meson8b-pwm";
+	compatible = "amlogic,meson8b-pwm-v2", "amlogic,meson8-pwm-v2";
+	clocks = <&xtal>,
+		 <0>, /* unknown/untested, the datasheet calls it "Video PLL" */
+		 <&clkc CLKID_FCLK_DIV4>,
+		 <&clkc CLKID_FCLK_DIV3>;
 };
 
 &rtc {
@@ -737,13 +749,13 @@
 
 &uart_B {
 	compatible = "amlogic,meson8b-uart";
-	clocks = <&xtal>, <&clkc CLKID_UART0>, <&clkc CLKID_CLK81>;
+	clocks = <&xtal>, <&clkc CLKID_UART1>, <&clkc CLKID_CLK81>;
 	clock-names = "xtal", "pclk", "baud";
 };
 
 &uart_C {
 	compatible = "amlogic,meson8b-uart";
-	clocks = <&xtal>, <&clkc CLKID_UART0>, <&clkc CLKID_CLK81>;
+	clocks = <&xtal>, <&clkc CLKID_UART2>, <&clkc CLKID_CLK81>;
 	clock-names = "xtal", "pclk", "baud";
 };
 
diff --git a/arch/arm/boot/dts/meson8m2-mxiii-plus.dts b/arch/arm/boot/dts/amlogic/meson8m2-mxiii-plus.dts
index fa6d55f1cfb9..08aa661e17ad 100644
--- a/arch/arm/boot/dts/meson8m2-mxiii-plus.dts
+++ b/arch/arm/boot/dts/amlogic/meson8m2-mxiii-plus.dts
@@ -19,7 +19,6 @@
 		ethernet0 = &ethmac;
 		i2c0 = &i2c_AO;
 		serial0 = &uart_AO;
-		serial1 = &uart_A;
 		mmc0 = &sd_card_slot;
 	};
 
@@ -27,7 +26,7 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	memory {
+	memory@40000000 {
 		device_type = "memory";
 		reg = <0x40000000 0x80000000>;
 	};
@@ -45,12 +44,32 @@
 		};
 	};
 
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+
+		pinctrl-0 = <&xtal_32k_out_pins>;
+		pinctrl-names = "default";
+
+		reset-gpios = <&gpio GPIOX_11 GPIO_ACTIVE_LOW>,
+			      <&gpio_ao GPIOAO_6 GPIO_ACTIVE_LOW>;
+
+		clocks = <&xtal_32k_out>;
+		clock-names = "ext_clock";
+	};
+
 	vcc_3v3: regulator-vcc3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "VCC3V3";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 	};
+
+	xtal_32k_out: xtal-32k-out-clk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "xtal_32k_out";
+	};
 };
 
 &cpu0 {
@@ -192,6 +211,27 @@
 	vref-supply = <&vddio_ao1v8>;
 };
 
+/* SDIO wifi */
+&sdhc {
+	status = "okay";
+
+	pinctrl-0 = <&sdxc_a_pins>;
+	pinctrl-names = "default";
+
+	bus-width = <4>;
+	max-frequency = <50000000>;
+
+	disable-wp;
+	non-removable;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_3v3>;
+};
+
 &sdio {
 	status = "okay";
 
@@ -222,6 +262,12 @@
 	pinctrl-0 = <&uart_a1_pins>, <&uart_a1_cts_rts_pins>;
 	pinctrl-names = "default";
 	uart-has-rtscts;
+
+	bluetooth {
+		compatible = "brcm,bcm20702a1";
+		shutdown-gpios = <&gpio GPIOX_20 GPIO_ACTIVE_HIGH>;
+		max-speed = <2000000>;
+	};
 };
 
 &uart_AO {
diff --git a/arch/arm/boot/dts/meson8m2.dtsi b/arch/arm/boot/dts/amlogic/meson8m2.dtsi
index 6725dd9fd825..6725dd9fd825 100644
--- a/arch/arm/boot/dts/meson8m2.dtsi
+++ b/arch/arm/boot/dts/amlogic/meson8m2.dtsi
diff --git a/arch/arm/boot/dts/arm/Makefile b/arch/arm/boot/dts/arm/Makefile
new file mode 100644
index 000000000000..07ebb64e2cd0
--- /dev/null
+++ b/arch/arm/boot/dts/arm/Makefile
@@ -0,0 +1,30 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_INTEGRATOR) += \
+	integratorap.dtb \
+	integratorap-im-pd1.dtb \
+	integratorcp.dtb
+dtb-$(CONFIG_ARCH_MPS2) += \
+	mps2-an385.dtb \
+	mps2-an399.dtb
+dtb-$(CONFIG_ARCH_REALVIEW) += \
+	arm-realview-pb1176.dtb \
+	arm-realview-pb11mp.dtb \
+	arm-realview-eb.dtb \
+	arm-realview-eb-bbrevd.dtb \
+	arm-realview-eb-11mp.dtb \
+	arm-realview-eb-11mp-bbrevd.dtb \
+	arm-realview-eb-11mp-ctrevb.dtb \
+	arm-realview-eb-11mp-bbrevd-ctrevb.dtb \
+	arm-realview-eb-a9mp.dtb \
+	arm-realview-eb-a9mp-bbrevd.dtb \
+	arm-realview-pba8.dtb \
+	arm-realview-pbx-a9.dtb
+dtb-$(CONFIG_ARCH_VERSATILE) += \
+	versatile-ab.dtb \
+	versatile-ab-ib2.dtb \
+	versatile-pb.dtb
+dtb-$(CONFIG_ARCH_VEXPRESS) += \
+	vexpress-v2p-ca5s.dtb \
+	vexpress-v2p-ca9.dtb \
+	vexpress-v2p-ca15-tc1.dtb \
+	vexpress-v2p-ca15_a7.dtb
diff --git a/arch/arm/boot/dts/arm-realview-eb-11mp-bbrevd-ctrevb.dts b/arch/arm/boot/dts/arm/arm-realview-eb-11mp-bbrevd-ctrevb.dts
index e18769df9fd9..e18769df9fd9 100644
--- a/arch/arm/boot/dts/arm-realview-eb-11mp-bbrevd-ctrevb.dts
+++ b/arch/arm/boot/dts/arm/arm-realview-eb-11mp-bbrevd-ctrevb.dts
diff --git a/arch/arm/boot/dts/arm-realview-eb-11mp-bbrevd.dts b/arch/arm/boot/dts/arm/arm-realview-eb-11mp-bbrevd.dts
index 26b1c69e9f43..26b1c69e9f43 100644
--- a/arch/arm/boot/dts/arm-realview-eb-11mp-bbrevd.dts
+++ b/arch/arm/boot/dts/arm/arm-realview-eb-11mp-bbrevd.dts
diff --git a/arch/arm/boot/dts/arm-realview-eb-11mp-ctrevb.dts b/arch/arm/boot/dts/arm/arm-realview-eb-11mp-ctrevb.dts
index e68527b0d552..e68527b0d552 100644
--- a/arch/arm/boot/dts/arm-realview-eb-11mp-ctrevb.dts
+++ b/arch/arm/boot/dts/arm/arm-realview-eb-11mp-ctrevb.dts
diff --git a/arch/arm/boot/dts/arm-realview-eb-11mp.dts b/arch/arm/boot/dts/arm/arm-realview-eb-11mp.dts
index aac1edd4b227..aac1edd4b227 100644
--- a/arch/arm/boot/dts/arm-realview-eb-11mp.dts
+++ b/arch/arm/boot/dts/arm/arm-realview-eb-11mp.dts
diff --git a/arch/arm/boot/dts/arm-realview-eb-a9mp-bbrevd.dts b/arch/arm/boot/dts/arm/arm-realview-eb-a9mp-bbrevd.dts
index 42efac7496ef..42efac7496ef 100644
--- a/arch/arm/boot/dts/arm-realview-eb-a9mp-bbrevd.dts
+++ b/arch/arm/boot/dts/arm/arm-realview-eb-a9mp-bbrevd.dts
diff --git a/arch/arm/boot/dts/arm-realview-eb-a9mp.dts b/arch/arm/boot/dts/arm/arm-realview-eb-a9mp.dts
index 967684b3636c..967684b3636c 100644
--- a/arch/arm/boot/dts/arm-realview-eb-a9mp.dts
+++ b/arch/arm/boot/dts/arm/arm-realview-eb-a9mp.dts
diff --git a/arch/arm/boot/dts/arm-realview-eb-bbrevd.dts b/arch/arm/boot/dts/arm/arm-realview-eb-bbrevd.dts
index f533c8b49d97..f533c8b49d97 100644
--- a/arch/arm/boot/dts/arm-realview-eb-bbrevd.dts
+++ b/arch/arm/boot/dts/arm/arm-realview-eb-bbrevd.dts
diff --git a/arch/arm/boot/dts/arm-realview-eb-bbrevd.dtsi b/arch/arm/boot/dts/arm/arm-realview-eb-bbrevd.dtsi
index a79e1d1d30a7..7f62aef9ca8a 100644
--- a/arch/arm/boot/dts/arm-realview-eb-bbrevd.dtsi
+++ b/arch/arm/boot/dts/arm/arm-realview-eb-bbrevd.dtsi
@@ -22,7 +22,7 @@
 
 / {
 	/* Introduce a fixed regulator for the new ethernet controller */
-	veth: fixedregulator@0 {
+	veth: regulator-veth {
 		compatible = "regulator-fixed";
 		regulator-name = "veth";
 		regulator-min-microvolt = <3300000>;
diff --git a/arch/arm/boot/dts/arm-realview-eb-mp.dtsi b/arch/arm/boot/dts/arm/arm-realview-eb-mp.dtsi
index 26783d053ac7..40f7515aa068 100644
--- a/arch/arm/boot/dts/arm-realview-eb-mp.dtsi
+++ b/arch/arm/boot/dts/arm/arm-realview-eb-mp.dtsi
@@ -103,7 +103,7 @@
 		};
 
 		/* PMU with one IRQ line per core */
-		pmu: pmu@0 {
+		pmu: pmu {
 			compatible = "arm,arm11mpcore-pmu";
 			interrupt-parent = <&intc>;
 			interrupts = <0 17 IRQ_TYPE_LEVEL_HIGH>,
diff --git a/arch/arm/boot/dts/arm-realview-eb.dts b/arch/arm/boot/dts/arm/arm-realview-eb.dts
index 15431077f00c..15431077f00c 100644
--- a/arch/arm/boot/dts/arm-realview-eb.dts
+++ b/arch/arm/boot/dts/arm/arm-realview-eb.dts
diff --git a/arch/arm/boot/dts/arm-realview-eb.dtsi b/arch/arm/boot/dts/arm/arm-realview-eb.dtsi
index 2dfb32bf9d48..16f784da5a55 100644
--- a/arch/arm/boot/dts/arm-realview-eb.dtsi
+++ b/arch/arm/boot/dts/arm/arm-realview-eb.dtsi
@@ -45,7 +45,7 @@
 	};
 
 	/* The voltage to the MMC card is hardwired at 3.3V */
-	vmmc: fixedregulator@0 {
+	vmmc: regulator-vmmc {
 		compatible = "regulator-fixed";
 		regulator-name = "vmmc";
 		regulator-min-microvolt = <3300000>;
@@ -53,13 +53,13 @@
 		regulator-boot-on;
         };
 
-	xtal24mhz: xtal24mhz@24M {
+	xtal24mhz: mclk: kmiclk: sspclk: uartclk: wdogclk: clock-24000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
 		clock-frequency = <24000000>;
 	};
 
-	timclk: timclk@1M {
+	timclk: clock-1000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
 		clock-div = <24>;
@@ -67,48 +67,8 @@
 		clocks = <&xtal24mhz>;
 	};
 
-	mclk: mclk@24M {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clock-div = <1>;
-		clock-mult = <1>;
-		clocks = <&xtal24mhz>;
-	};
-
-	kmiclk: kmiclk@24M {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clock-div = <1>;
-		clock-mult = <1>;
-		clocks = <&xtal24mhz>;
-	};
-
-	sspclk: sspclk@24M {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clock-div = <1>;
-		clock-mult = <1>;
-		clocks = <&xtal24mhz>;
-	};
-
-	uartclk: uartclk@24M {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clock-div = <1>;
-		clock-mult = <1>;
-		clocks = <&xtal24mhz>;
-	};
-
-	wdogclk: wdogclk@24M {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clock-div = <1>;
-		clock-mult = <1>;
-		clocks = <&xtal24mhz>;
-	};
-
 	/* FIXME: this actually hangs off the PLL clocks */
-	pclk: pclk@0 {
+	pclk: clock-pclk {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
 		clock-frequency = <0>;
@@ -399,7 +359,7 @@
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x1000d000 0x1000>;
 			clocks = <&sspclk>, <&pclk>;
-			clock-names = "SSPCLK", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 		};
 
 		wdog: watchdog@10010000 {
diff --git a/arch/arm/boot/dts/arm-realview-pb1176.dts b/arch/arm/boot/dts/arm/arm-realview-pb1176.dts
index 06b8723b09eb..b9b10cbd65aa 100644
--- a/arch/arm/boot/dts/arm-realview-pb1176.dts
+++ b/arch/arm/boot/dts/arm/arm-realview-pb1176.dts
@@ -63,13 +63,13 @@
 		regulator-boot-on;
 	};
 
-	xtal24mhz: xtal24mhz@24M {
+	xtal24mhz: mclk: kmiclk: sspclk: uartclk: clock-24000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
 		clock-frequency = <24000000>;
 	};
 
-	timclk: timclk@1M {
+	timclk: clock-1000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
 		clock-div = <24>;
@@ -77,40 +77,8 @@
 		clocks = <&xtal24mhz>;
 	};
 
-	mclk: mclk@24M {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clock-div = <1>;
-		clock-mult = <1>;
-		clocks = <&xtal24mhz>;
-	};
-
-	kmiclk: kmiclk@24M {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clock-div = <1>;
-		clock-mult = <1>;
-		clocks = <&xtal24mhz>;
-	};
-
-	sspclk: sspclk@24M {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clock-div = <1>;
-		clock-mult = <1>;
-		clocks = <&xtal24mhz>;
-	};
-
-	uartclk: uartclk@24M {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clock-div = <1>;
-		clock-mult = <1>;
-		clocks = <&xtal24mhz>;
-	};
-
 	/* FIXME: this actually hangs off the PLL clocks */
-	pclk: pclk@0 {
+	pclk: clock-pclk {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
 		clock-frequency = <0>;
@@ -410,7 +378,7 @@
 			interrupt-parent = <&intc_dc1176>;
 			interrupts = <0 17 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&sspclk>, <&pclk>;
-			clock-names = "SSPCLK", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 		};
 
 		pb1176_serial0: serial@1010c000 {
@@ -451,7 +419,7 @@
 
 		/* Direct-mapped development chip ROM */
 		pb1176_rom@10200000 {
-			compatible = "direct-mapped";
+			compatible = "mtd-rom";
 			reg = <0x10200000 0x4000>;
 			bank-width = <1>;
 		};
diff --git a/arch/arm/boot/dts/arm-realview-pb11mp.dts b/arch/arm/boot/dts/arm/arm-realview-pb11mp.dts
index 295aef448123..db1b6793cd2c 100644
--- a/arch/arm/boot/dts/arm-realview-pb11mp.dts
+++ b/arch/arm/boot/dts/arm/arm-realview-pb11mp.dts
@@ -92,7 +92,7 @@
 		      <0x1f000100 0x100>;
 	};
 
-	L2: cache-controller {
+	L2: cache-controller@1f002000 {
 		compatible = "arm,l220-cache";
 		reg = <0x1f002000 0x1000>;
 		interrupt-parent = <&intc_tc11mp>;
@@ -163,19 +163,19 @@
 		regulator-boot-on;
 	};
 
-	xtal24mhz: xtal24mhz@24M {
+	xtal24mhz: mclk: kmiclk: sspclk: uartclk: wdogclk: clock-24000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
 		clock-frequency = <24000000>;
 	};
 
-	refclk32khz: refclk32khz {
+	refclk32khz: clock-32768 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <32768>;
 	};
 
-	timclk: timclk@1M {
+	timclk: clock-1000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
 		clock-div = <24>;
@@ -183,48 +183,8 @@
 		clocks = <&xtal24mhz>;
 	};
 
-	mclk: mclk@24M {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clock-div = <1>;
-		clock-mult = <1>;
-		clocks = <&xtal24mhz>;
-	};
-
-	kmiclk: kmiclk@24M {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clock-div = <1>;
-		clock-mult = <1>;
-		clocks = <&xtal24mhz>;
-	};
-
-	sspclk: sspclk@24M {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clock-div = <1>;
-		clock-mult = <1>;
-		clocks = <&xtal24mhz>;
-	};
-
-	uartclk: uartclk@24M {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clock-div = <1>;
-		clock-mult = <1>;
-		clocks = <&xtal24mhz>;
-	};
-
-	wdogclk: wdogclk@24M {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clock-div = <1>;
-		clock-mult = <1>;
-		clocks = <&xtal24mhz>;
-	};
-
 	/* FIXME: this actually hangs off the PLL clocks */
-	pclk: pclk@0 {
+	pclk: clock-pclk {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
 		clock-frequency = <0>;
@@ -555,7 +515,7 @@
 			interrupt-parent = <&intc_pb11mp>;
 			interrupts = <0 11 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&sspclk>, <&pclk>;
-			clock-names = "SSPCLK", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 		};
 
 		watchdog@1000f000 {
diff --git a/arch/arm/boot/dts/arm-realview-pba8.dts b/arch/arm/boot/dts/arm/arm-realview-pba8.dts
index d3238c252b59..d2e0082245f9 100644
--- a/arch/arm/boot/dts/arm-realview-pba8.dts
+++ b/arch/arm/boot/dts/arm/arm-realview-pba8.dts
@@ -40,7 +40,7 @@
 		};
 	};
 
-	pmu: pmu@0 {
+	pmu: pmu {
 		compatible = "arm,cortex-a8-pmu";
 		interrupt-parent = <&intc>;
 		interrupts = <0 47 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/arm-realview-pbx-a9.dts b/arch/arm/boot/dts/arm/arm-realview-pbx-a9.dts
index 85d3968fbb91..507ad7ac4974 100644
--- a/arch/arm/boot/dts/arm-realview-pbx-a9.dts
+++ b/arch/arm/boot/dts/arm/arm-realview-pbx-a9.dts
@@ -97,7 +97,7 @@
 		interrupts = <1 14 0xf04>;
 	};
 
-	pmu: pmu@0 {
+	pmu: pmu {
 		compatible = "arm,cortex-a9-pmu";
 		interrupt-parent = <&intc>;
 		interrupts = <0 44 IRQ_TYPE_LEVEL_HIGH>,
diff --git a/arch/arm/boot/dts/arm-realview-pbx.dtsi b/arch/arm/boot/dts/arm/arm-realview-pbx.dtsi
index 6f61f968d689..e625403a9456 100644
--- a/arch/arm/boot/dts/arm-realview-pbx.dtsi
+++ b/arch/arm/boot/dts/arm/arm-realview-pbx.dtsi
@@ -62,19 +62,19 @@
 		regulator-boot-on;
 	};
 
-	xtal24mhz: xtal24mhz@24M {
+	xtal24mhz: mclk: kmiclk: sspclk: uartclk: wdogclk: clock-24000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
 		clock-frequency = <24000000>;
 	};
 
-	refclk32khz: refclk32khz {
+	refclk32khz: clock-32768 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
 		clock-frequency = <32768>;
 	};
 
-	timclk: timclk@1M {
+	timclk: clock-1000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
 		clock-div = <24>;
@@ -82,48 +82,8 @@
 		clocks = <&xtal24mhz>;
 	};
 
-	mclk: mclk@24M {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clock-div = <1>;
-		clock-mult = <1>;
-		clocks = <&xtal24mhz>;
-	};
-
-	kmiclk: kmiclk@24M {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clock-div = <1>;
-		clock-mult = <1>;
-		clocks = <&xtal24mhz>;
-	};
-
-	sspclk: sspclk@24M {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clock-div = <1>;
-		clock-mult = <1>;
-		clocks = <&xtal24mhz>;
-	};
-
-	uartclk: uartclk@24M {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clock-div = <1>;
-		clock-mult = <1>;
-		clocks = <&xtal24mhz>;
-	};
-
-	wdogclk: wdogclk@24M {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clock-div = <1>;
-		clock-mult = <1>;
-		clocks = <&xtal24mhz>;
-	};
-
 	/* FIXME: this actually hangs off the PLL clocks */
-	pclk: pclk@0 {
+	pclk: clock-pclk {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
 		clock-frequency = <0>;
@@ -390,7 +350,7 @@
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x1000d000 0x1000>;
 			clocks = <&sspclk>, <&pclk>;
-			clock-names = "SSPCLK", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 		};
 
 		wdog0: watchdog@1000f000 {
diff --git a/arch/arm/boot/dts/integrator.dtsi b/arch/arm/boot/dts/arm/integrator.dtsi
index ad868cfebc94..7f1c8ee9dd8a 100644
--- a/arch/arm/boot/dts/integrator.dtsi
+++ b/arch/arm/boot/dts/arm/integrator.dtsi
@@ -88,12 +88,12 @@
 			interrupts = <8>;
 		};
 
-		uart@16000000 {
+		serial@16000000 {
 			reg = <0x16000000 0x1000>;
 			interrupts = <1>;
 		};
 
-		uart@17000000 {
+		serial@17000000 {
 			reg = <0x17000000 0x1000>;
 			interrupts = <2>;
 		};
diff --git a/arch/arm/boot/dts/integratorap-im-pd1.dts b/arch/arm/boot/dts/arm/integratorap-im-pd1.dts
index d47bfb66d069..db13e09f2fab 100644
--- a/arch/arm/boot/dts/integratorap-im-pd1.dts
+++ b/arch/arm/boot/dts/arm/integratorap-im-pd1.dts
@@ -54,7 +54,7 @@
 	};
 
 	/* Also used for the Smart Card Interface SCI */
-	impd1_uartclk: clock@1_4 {
+	impd1_uartclk: clock-uart {
 		compatible = "fixed-factor-clock";
 		#clock-cells = <0>;
 		clock-div = <4>;
@@ -64,7 +64,7 @@
 	};
 
 	/* For the SSP the clock is divided by 64 */
-	impd1_sspclk: clock@1_64 {
+	impd1_sspclk: clock-ssp {
 		compatible = "fixed-factor-clock";
 		#clock-cells = <0>;
 		clock-div = <64>;
@@ -129,8 +129,6 @@
 
 	bridge {
 		compatible = "ti,ths8134b", "ti,ths8134";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
 		ports {
 			#address-cells = <1>;
@@ -154,6 +152,7 @@
 
 	vga {
 		compatible = "vga-connector";
+		label = "J30";
 
 		port {
 			vga_con_in: endpoint {
@@ -162,7 +161,7 @@
 		};
 	};
 
-	uart@100000 {
+	serial@100000 {
 		compatible = "arm,pl011", "arm,primecell";
 		reg = <0x00100000 0x1000>;
 		interrupts-extended = <&impd1_vic 1>;
@@ -170,7 +169,7 @@
 		clock-names = "uartclk", "apb_pclk";
 	};
 
-	uart@200000 {
+	serial@200000 {
 		compatible = "arm,pl011", "arm,primecell";
 		reg = <0x00200000 0x1000>;
 		interrupts-extended = <&impd1_vic 2>;
@@ -178,12 +177,12 @@
 		clock-names = "uartclk", "apb_pclk";
 	};
 
-	ssp@300000 {
+	spi@300000 {
 		compatible = "arm,pl022", "arm,primecell";
 		reg = <0x00300000 0x1000>;
 		interrupts-extended = <&impd1_vic 3>;
 		clocks = <&impd1_sspclk>, <&sysclk>;
-		clock-names = "spiclk", "apb_pclk";
+		clock-names = "sspclk", "apb_pclk";
 	};
 
 	impd1_gpio0: gpio@400000 {
@@ -249,6 +248,7 @@
 		/* 640x480 16bpp @ 25.175MHz is 36827428 bytes/s */
 		max-memory-bandwidth = <40000000>;
 		memory-region = <&impd1_ram>;
+		dma-ranges;
 
 		port@0 {
 			#address-cells = <1>;
diff --git a/arch/arm/boot/dts/integratorap.dts b/arch/arm/boot/dts/arm/integratorap.dts
index 9b652cc27b14..9b6a1dbaf265 100644
--- a/arch/arm/boot/dts/integratorap.dts
+++ b/arch/arm/boot/dts/arm/integratorap.dts
@@ -57,22 +57,14 @@
 	};
 
 	/* 24 MHz chrystal on the Integrator/AP development board */
-	xtal24mhz: xtal24mhz@24M {
+	xtal24mhz: pclk: clock-24000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
 		clock-frequency = <24000000>;
 	};
 
-	pclk: pclk@0 {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clock-div = <1>;
-		clock-mult = <1>;
-		clocks = <&xtal24mhz>;
-	};
-
 	/* The UART clock is 14.74 MHz divided by an ICS525 */
-	uartclk: uartclk@14.74M {
+	uartclk: clock-14745600 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
 		clock-frequency = <14745600>;
@@ -81,7 +73,7 @@
 
 	core-module@10000000 {
 		/* 24 MHz chrystal on the core module */
-		cm24mhz: cm24mhz@24M {
+		cm24mhz: clock-24000000 {
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <24000000>;
@@ -158,8 +150,9 @@
 		valid-mask = <0x003fffff>;
 	};
 
-	pci: pciv3@62000000 {
+	pci: pci@62000000 {
 		compatible = "arm,integrator-ap-pci", "v3,v360epc-pci";
+		device_type = "pci";
 		#interrupt-cells = <1>;
 		#size-cells = <2>;
 		#address-cells = <3>;
@@ -217,14 +210,14 @@
 			clock-names = "apb_pclk";
 		};
 
-		uart0: uart@16000000 {
+		uart0: serial@16000000 {
 			compatible = "arm,pl010", "arm,primecell";
 			arm,primecell-periphid = <0x00041010>;
 			clocks = <&uartclk>, <&pclk>;
 			clock-names = "uartclk", "apb_pclk";
 		};
 
-		uart1: uart@17000000 {
+		uart1: serial@17000000 {
 			compatible = "arm,pl010", "arm,primecell";
 			arm,primecell-periphid = <0x00041010>;
 			clocks = <&uartclk>, <&pclk>;
@@ -261,7 +254,7 @@
 		lm0: bus@c0000000 {
 			compatible = "simple-bus";
 			ranges = <0x00000000 0xc0000000 0x10000000>;
-			dma-ranges = <0x00000000 0x80000000 0x10000000>;
+			dma-ranges = <0x00000000 0xc0000000 0x10000000>;
 			reg = <0xc0000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -269,7 +262,7 @@
 		lm1: bus@d0000000 {
 			compatible = "simple-bus";
 			ranges = <0x00000000 0xd0000000 0x10000000>;
-			dma-ranges = <0x00000000 0x80000000 0x10000000>;
+			dma-ranges = <0x00000000 0xd0000000 0x10000000>;
 			reg = <0xd0000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -277,7 +270,7 @@
 		lm2: bus@e0000000 {
 			compatible = "simple-bus";
 			ranges = <0x00000000 0xe0000000 0x10000000>;
-			dma-ranges = <0x00000000 0x80000000 0x10000000>;
+			dma-ranges = <0x00000000 0xe0000000 0x10000000>;
 			reg = <0xe0000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -285,7 +278,7 @@
 		lm3: bus@f0000000 {
 			compatible = "simple-bus";
 			ranges = <0x00000000 0xf0000000 0x10000000>;
-			dma-ranges = <0x00000000 0x80000000 0x10000000>;
+			dma-ranges = <0x00000000 0xf0000000 0x10000000>;
 			reg = <0xf0000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
diff --git a/arch/arm/boot/dts/integratorcp.dts b/arch/arm/boot/dts/arm/integratorcp.dts
index 38fc7e81bdb6..8ad1a8957ace 100644
--- a/arch/arm/boot/dts/integratorcp.dts
+++ b/arch/arm/boot/dts/arm/integratorcp.dts
@@ -47,14 +47,14 @@
 	 */
 
 	/* The codec chrystal operates at 24.576 MHz */
-	xtal_codec: xtal24.576@24.576M {
+	xtal_codec: clock-24576000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
 		clock-frequency = <24576000>;
 	};
 
 	/* The chrystal is divided by 2 by the codec for the AACI bit clock */
-	aaci_bitclk: aaci_bitclk@12.288M {
+	aaci_bitclk: clock-12288000 {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
 		clock-div = <2>;
@@ -63,21 +63,21 @@
 	};
 
 	/* This is a 25MHz chrystal on the base board */
-	xtal25mhz: xtal25mhz@25M {
+	xtal25mhz: clock-25000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
 		clock-frequency = <25000000>;
 	};
 
 	/* The UART clock is 14.74 MHz divided from 25MHz by an ICS525 */
-	uartclk: uartclk@14.74M {
+	uartclk: clock-14745600 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
 		clock-frequency = <14745600>;
 	};
 
 	/* Actually sysclk I think */
-	pclk: pclk@0 {
+	pclk: clock-pclk {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
 		clock-frequency = <0>;
@@ -85,7 +85,7 @@
 
 	core-module@10000000 {
 		/* 24 MHz chrystal on the core module */
-		cm24mhz: cm24mhz@24M {
+		cm24mhz: clock-24000000 {
 			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <24000000>;
@@ -131,7 +131,7 @@
 		};
 
 		/* The timer clock is the 24 MHz oscillator divided to 1MHz */
-		timclk: timclk@1M {
+		timclk: clock-1000000 {
 			#clock-cells = <0>;
 			compatible = "fixed-factor-clock";
 			clock-div = <24>;
@@ -244,13 +244,13 @@
 			clock-names = "apb_pclk";
 		};
 
-		uart@16000000 {
+		serial@16000000 {
 			compatible = "arm,pl011", "arm,primecell";
 			clocks = <&uartclk>, <&pclk>;
 			clock-names = "uartclk", "apb_pclk";
 		};
 
-		uart@17000000 {
+		serial@17000000 {
 			compatible = "arm,pl011", "arm,primecell";
 			clocks = <&uartclk>, <&pclk>;
 			clock-names = "uartclk", "apb_pclk";
diff --git a/arch/arm/boot/dts/mps2-an385.dts b/arch/arm/boot/dts/arm/mps2-an385.dts
index aebbebfc25d1..aebbebfc25d1 100644
--- a/arch/arm/boot/dts/mps2-an385.dts
+++ b/arch/arm/boot/dts/arm/mps2-an385.dts
diff --git a/arch/arm/boot/dts/mps2-an399.dts b/arch/arm/boot/dts/arm/mps2-an399.dts
index 349abf70b2a5..349abf70b2a5 100644
--- a/arch/arm/boot/dts/mps2-an399.dts
+++ b/arch/arm/boot/dts/arm/mps2-an399.dts
diff --git a/arch/arm/boot/dts/mps2.dtsi b/arch/arm/boot/dts/arm/mps2.dtsi
index b99577d411b1..e240bc8aa605 100644
--- a/arch/arm/boot/dts/mps2.dtsi
+++ b/arch/arm/boot/dts/arm/mps2.dtsi
@@ -42,43 +42,43 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
-#include "armv7-m.dtsi"
+#include "../armv7-m.dtsi"
 
 / {
 	#address-cells = <1>;
 	#size-cells = <1>;
 
-	oscclk0: clk-osc0 {
+	oscclk0: clock-50000000 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <50000000>;
 	};
 
-	oscclk1: clk-osc1 {
+	oscclk1: clock-24576000 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <24576000>;
 	};
 
-	oscclk2: clk-osc2 {
+	oscclk2: clock-25000000 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <25000000>;
 	};
 
-	cfgclk: clk-cfg {
+	cfgclk: clock-5000000 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <5000000>;
 	};
 
-	spicfgclk: clk-spicfg {
+	spicfgclk: clock-75000000 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <75000000>;
 	};
 
-	sysclk: clk-sys {
+	sysclk: spiclcd: spicon: i2cclcd: i2caud: clock-sys {
 		compatible = "fixed-factor-clock";
 		clocks = <&oscclk0>;
 		#clock-cells = <0>;
@@ -86,7 +86,7 @@
 		clock-mult = <1>;
 	};
 
-	audmclk: clk-audm {
+	audmclk: clk-12388000 {
 		compatible = "fixed-factor-clock";
 		clocks = <&oscclk1>;
 		#clock-cells = <0>;
@@ -94,7 +94,7 @@
 		clock-mult = <1>;
 	};
 
-	audsclk: clk-auds {
+	audsclk: clk-3072000 {
 		compatible = "fixed-factor-clock";
 		clocks = <&oscclk1>;
 		#clock-cells = <0>;
@@ -102,38 +102,6 @@
 		clock-mult = <1>;
 	};
 
-	spiclcd: clk-cpiclcd {
-		compatible = "fixed-factor-clock";
-		clocks = <&oscclk0>;
-		#clock-cells = <0>;
-		clock-div = <2>;
-		clock-mult = <1>;
-	};
-
-	spicon: clk-spicon {
-		compatible = "fixed-factor-clock";
-		clocks = <&oscclk0>;
-		#clock-cells = <0>;
-		clock-div = <2>;
-		clock-mult = <1>;
-	};
-
-	i2cclcd: clk-i2cclcd {
-		compatible = "fixed-factor-clock";
-		clocks = <&oscclk0>;
-		#clock-cells = <0>;
-		clock-div = <2>;
-		clock-mult = <1>;
-	};
-
-	i2caud: clk-i2caud {
-		compatible = "fixed-factor-clock";
-		clocks = <&oscclk0>;
-		#clock-cells = <0>;
-		clock-div = <2>;
-		clock-mult = <1>;
-	};
-
 	soc {
 		compatible = "simple-bus";
 		ranges;
diff --git a/arch/arm/boot/dts/versatile-ab-ib2.dts b/arch/arm/boot/dts/arm/versatile-ab-ib2.dts
index 7ebb0dfd0467..7ebb0dfd0467 100644
--- a/arch/arm/boot/dts/versatile-ab-ib2.dts
+++ b/arch/arm/boot/dts/arm/versatile-ab-ib2.dts
diff --git a/arch/arm/boot/dts/versatile-ab.dts b/arch/arm/boot/dts/arm/versatile-ab.dts
index 79f7cc241282..635ab9268899 100644
--- a/arch/arm/boot/dts/versatile-ab.dts
+++ b/arch/arm/boot/dts/arm/versatile-ab.dts
@@ -24,7 +24,7 @@
 		reg = <0x0 0x08000000>;
 	};
 
-	xtal24mhz: xtal24mhz@24M {
+	xtal24mhz: clock-24000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
 		clock-frequency = <24000000>;
@@ -32,8 +32,6 @@
 
 	bridge {
 		compatible = "ti,ths8134b", "ti,ths8134";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
 		ports {
 			#address-cells = <1>;
@@ -59,6 +57,7 @@
 
 	vga {
 		compatible = "vga-connector";
+		label = "J1";
 
 		port {
 			vga_con_in: endpoint {
@@ -143,14 +142,14 @@
 		};
 
 		/* OSC1 on AB, OSC4 on PB */
-		osc1: cm_aux_osc@24M {
+		osc1: clock-osc {
 			#clock-cells = <0>;
 			compatible = "arm,versatile-cm-auxosc";
 			clocks = <&xtal24mhz>;
 		};
 
 		/* The timer clock is the 24 MHz oscillator divided to 1MHz */
-		timclk: timclk@1M {
+		timclk: clock-1000000 {
 			#clock-cells = <0>;
 			compatible = "fixed-factor-clock";
 			clock-div = <24>;
@@ -158,7 +157,7 @@
 			clocks = <&xtal24mhz>;
 		};
 
-		pclk: pclk@24M {
+		pclk: clock-pclk {
 			#clock-cells = <0>;
 			compatible = "fixed-factor-clock";
 			clock-div = <1>;
@@ -237,7 +236,7 @@
 			clock-names = "apb_pclk";
 		};
 
-		uart0: uart@101f1000 {
+		uart0: serial@101f1000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x101f1000 0x1000>;
 			interrupts = <12>;
@@ -245,7 +244,7 @@
 			clock-names = "uartclk", "apb_pclk";
 		};
 
-		uart1: uart@101f2000 {
+		uart1: serial@101f2000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x101f2000 0x1000>;
 			interrupts = <13>;
@@ -253,7 +252,7 @@
 			clock-names = "uartclk", "apb_pclk";
 		};
 
-		uart2: uart@101f3000 {
+		uart2: serial@101f3000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x101f3000 0x1000>;
 			interrupts = <14>;
@@ -391,7 +390,7 @@
 			reg = <0x101f4000 0x1000>;
 			interrupts = <11>;
 			clocks = <&xtal24mhz>, <&pclk>;
-			clock-names = "SSPCLK", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 		};
 
 		fpga {
diff --git a/arch/arm/boot/dts/versatile-pb.dts b/arch/arm/boot/dts/arm/versatile-pb.dts
index e7e751a858d8..fc21ce54b33a 100644
--- a/arch/arm/boot/dts/versatile-pb.dts
+++ b/arch/arm/boot/dts/arm/versatile-pb.dts
@@ -85,7 +85,7 @@
 				 */
 				interrupts-extended = <&sic 22 &sic 23>;
 			};
-			uart@9000 {
+			serial@9000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0x9000 0x1000>;
 				interrupt-parent = <&sic>;
diff --git a/arch/arm/boot/dts/vexpress-v2m-rs1.dtsi b/arch/arm/boot/dts/arm/vexpress-v2m-rs1.dtsi
index 8af4b77fe655..158b3923eae3 100644
--- a/arch/arm/boot/dts/vexpress-v2m-rs1.dtsi
+++ b/arch/arm/boot/dts/arm/vexpress-v2m-rs1.dtsi
@@ -20,7 +20,7 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 
 / {
-	v2m_fixed_3v3: fixed-regulator-0 {
+	v2m_fixed_3v3: regulator-3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "3V3";
 		regulator-min-microvolt = <3300000>;
@@ -28,21 +28,21 @@
 		regulator-always-on;
 	};
 
-	v2m_clk24mhz: clk24mhz {
+	v2m_clk24mhz: clock-24000000 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <24000000>;
 		clock-output-names = "v2m:clk24mhz";
 	};
 
-	v2m_refclk1mhz: refclk1mhz {
+	v2m_refclk1mhz: clock-1000000 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <1000000>;
 		clock-output-names = "v2m:refclk1mhz";
 	};
 
-	v2m_refclk32khz: refclk32khz {
+	v2m_refclk32khz: clock-32768 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <32768>;
diff --git a/arch/arm/boot/dts/vexpress-v2m.dtsi b/arch/arm/boot/dts/arm/vexpress-v2m.dtsi
index f434fe5cf4a1..be03f2a8a57a 100644
--- a/arch/arm/boot/dts/vexpress-v2m.dtsi
+++ b/arch/arm/boot/dts/arm/vexpress-v2m.dtsi
@@ -216,7 +216,7 @@
 					clock-names = "KMIREFCLK", "apb_pclk";
 				};
 
-				v2m_serial0: uart@9000 {
+				v2m_serial0: serial@9000 {
 					compatible = "arm,pl011", "arm,primecell";
 					reg = <0x09000 0x1000>;
 					interrupts = <5>;
@@ -224,7 +224,7 @@
 					clock-names = "uartclk", "apb_pclk";
 				};
 
-				v2m_serial1: uart@a000 {
+				v2m_serial1: serial@a000 {
 					compatible = "arm,pl011", "arm,primecell";
 					reg = <0x0a000 0x1000>;
 					interrupts = <6>;
@@ -232,7 +232,7 @@
 					clock-names = "uartclk", "apb_pclk";
 				};
 
-				v2m_serial2: uart@b000 {
+				v2m_serial2: serial@b000 {
 					compatible = "arm,pl011", "arm,primecell";
 					reg = <0x0b000 0x1000>;
 					interrupts = <7>;
@@ -240,7 +240,7 @@
 					clock-names = "uartclk", "apb_pclk";
 				};
 
-				v2m_serial3: uart@c000 {
+				v2m_serial3: serial@c000 {
 					compatible = "arm,pl011", "arm,primecell";
 					reg = <0x0c000 0x1000>;
 					interrupts = <8>;
@@ -351,7 +351,7 @@
 				};
 			};
 
-			v2m_fixed_3v3: fixed-regulator-0 {
+			v2m_fixed_3v3: regulator-3v3 {
 				compatible = "regulator-fixed";
 				regulator-name = "3V3";
 				regulator-min-microvolt = <3300000>;
@@ -359,21 +359,21 @@
 				regulator-always-on;
 			};
 
-			v2m_clk24mhz: clk24mhz {
+			v2m_clk24mhz: clock-24000000 {
 				compatible = "fixed-clock";
 				#clock-cells = <0>;
 				clock-frequency = <24000000>;
 				clock-output-names = "v2m:clk24mhz";
 			};
 
-			v2m_refclk1mhz: refclk1mhz {
+			v2m_refclk1mhz: clock-1000000 {
 				compatible = "fixed-clock";
 				#clock-cells = <0>;
 				clock-frequency = <1000000>;
 				clock-output-names = "v2m:refclk1mhz";
 			};
 
-			v2m_refclk32khz: refclk32khz {
+			v2m_refclk32khz: clock-32768 {
 				compatible = "fixed-clock";
 				#clock-cells = <0>;
 				clock-frequency = <32768>;
@@ -383,49 +383,49 @@
 			leds {
 				compatible = "gpio-leds";
 
-				user1 {
+				led-user1 {
 					label = "v2m:green:user1";
 					gpios = <&v2m_led_gpios 0 0>;
 					linux,default-trigger = "heartbeat";
 				};
 
-				user2 {
+				led-user2 {
 					label = "v2m:green:user2";
 					gpios = <&v2m_led_gpios 1 0>;
 					linux,default-trigger = "mmc0";
 				};
 
-				user3 {
+				led-user3 {
 					label = "v2m:green:user3";
 					gpios = <&v2m_led_gpios 2 0>;
 					linux,default-trigger = "cpu0";
 				};
 
-				user4 {
+				led-user4 {
 					label = "v2m:green:user4";
 					gpios = <&v2m_led_gpios 3 0>;
 					linux,default-trigger = "cpu1";
 				};
 
-				user5 {
+				led-user5 {
 					label = "v2m:green:user5";
 					gpios = <&v2m_led_gpios 4 0>;
 					linux,default-trigger = "cpu2";
 				};
 
-				user6 {
+				led-user6 {
 					label = "v2m:green:user6";
 					gpios = <&v2m_led_gpios 5 0>;
 					linux,default-trigger = "cpu3";
 				};
 
-				user7 {
+				led-user7 {
 					label = "v2m:green:user7";
 					gpios = <&v2m_led_gpios 6 0>;
 					linux,default-trigger = "cpu4";
 				};
 
-				user8 {
+				led-user8 {
 					label = "v2m:green:user8";
 					gpios = <&v2m_led_gpios 7 0>;
 					linux,default-trigger = "cpu5";
@@ -436,7 +436,7 @@
 				compatible = "arm,vexpress,config-bus";
 				arm,vexpress,config-bridge = <&v2m_sysreg>;
 
-				oscclk0 {
+				clock-controller-0 {
 					/* MCC static memory clock */
 					compatible = "arm,vexpress-osc";
 					arm,vexpress-sysreg,func = <1 0>;
@@ -445,7 +445,7 @@
 					clock-output-names = "v2m:oscclk0";
 				};
 
-				v2m_oscclk1: oscclk1 {
+				v2m_oscclk1: clock-controller-1 {
 					/* CLCD clock */
 					compatible = "arm,vexpress-osc";
 					arm,vexpress-sysreg,func = <1 1>;
@@ -454,7 +454,7 @@
 					clock-output-names = "v2m:oscclk1";
 				};
 
-				v2m_oscclk2: oscclk2 {
+				v2m_oscclk2: clock-controller-2 {
 					/* IO FPGA peripheral clock */
 					compatible = "arm,vexpress-osc";
 					arm,vexpress-sysreg,func = <1 2>;
@@ -463,7 +463,7 @@
 					clock-output-names = "v2m:oscclk2";
 				};
 
-				volt-vio {
+				regulator-vio {
 					/* Logic level voltage */
 					compatible = "arm,vexpress-volt";
 					arm,vexpress-sysreg,func = <2 0>;
diff --git a/arch/arm/boot/dts/vexpress-v2p-ca15-tc1.dts b/arch/arm/boot/dts/arm/vexpress-v2p-ca15-tc1.dts
index 679537e17ff5..5a91e936edef 100644
--- a/arch/arm/boot/dts/vexpress-v2p-ca15-tc1.dts
+++ b/arch/arm/boot/dts/arm/vexpress-v2p-ca15-tc1.dts
@@ -142,7 +142,7 @@
 		compatible = "arm,vexpress,config-bus";
 		arm,vexpress,config-bridge = <&v2m_sysreg>;
 
-		oscclk0 {
+		clock-controller-0 {
 			/* CPU PLL reference clock */
 			compatible = "arm,vexpress-osc";
 			arm,vexpress-sysreg,func = <1 0>;
@@ -151,7 +151,7 @@
 			clock-output-names = "oscclk0";
 		};
 
-		oscclk4 {
+		clock-controller-4 {
 			/* Multiplexed AXI master clock */
 			compatible = "arm,vexpress-osc";
 			arm,vexpress-sysreg,func = <1 4>;
@@ -160,7 +160,7 @@
 			clock-output-names = "oscclk4";
 		};
 
-		hdlcd_clk: oscclk5 {
+		hdlcd_clk: clock-controller-5 {
 			/* HDLCD PLL reference clock */
 			compatible = "arm,vexpress-osc";
 			arm,vexpress-sysreg,func = <1 5>;
@@ -169,7 +169,7 @@
 			clock-output-names = "oscclk5";
 		};
 
-		smbclk: oscclk6 {
+		smbclk: clock-controller-6 {
 			/* SMB clock */
 			compatible = "arm,vexpress-osc";
 			arm,vexpress-sysreg,func = <1 6>;
@@ -178,7 +178,7 @@
 			clock-output-names = "oscclk6";
 		};
 
-		sys_pll: oscclk7 {
+		sys_pll: clock-controller-7 {
 			/* SYS PLL reference clock */
 			compatible = "arm,vexpress-osc";
 			arm,vexpress-sysreg,func = <1 7>;
@@ -187,7 +187,7 @@
 			clock-output-names = "oscclk7";
 		};
 
-		oscclk8 {
+		clock-controller-8 {
 			/* DDR2 PLL reference clock */
 			compatible = "arm,vexpress-osc";
 			arm,vexpress-sysreg,func = <1 8>;
@@ -196,7 +196,7 @@
 			clock-output-names = "oscclk8";
 		};
 
-		volt-cores {
+		regulator-cores {
 			/* CPU core voltage */
 			compatible = "arm,vexpress-volt";
 			arm,vexpress-sysreg,func = <2 0>;
diff --git a/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts b/arch/arm/boot/dts/arm/vexpress-v2p-ca15_a7.dts
index 511e87cc2bc5..6ef23c53d2d8 100644
--- a/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts
+++ b/arch/arm/boot/dts/arm/vexpress-v2p-ca15_a7.dts
@@ -253,7 +253,7 @@
 		compatible = "arm,vexpress,config-bus";
 		arm,vexpress,config-bridge = <&v2m_sysreg>;
 
-		oscclk0 {
+		clock-controller-0 {
 			/* A15 PLL 0 reference clock */
 			compatible = "arm,vexpress-osc";
 			arm,vexpress-sysreg,func = <1 0>;
@@ -262,7 +262,7 @@
 			clock-output-names = "oscclk0";
 		};
 
-		oscclk1 {
+		clock-controller-1 {
 			/* A15 PLL 1 reference clock */
 			compatible = "arm,vexpress-osc";
 			arm,vexpress-sysreg,func = <1 1>;
@@ -271,7 +271,7 @@
 			clock-output-names = "oscclk1";
 		};
 
-		oscclk2 {
+		clock-controller-2 {
 			/* A7 PLL 0 reference clock */
 			compatible = "arm,vexpress-osc";
 			arm,vexpress-sysreg,func = <1 2>;
@@ -280,7 +280,7 @@
 			clock-output-names = "oscclk2";
 		};
 
-		oscclk3 {
+		clock-controller-3 {
 			/* A7 PLL 1 reference clock */
 			compatible = "arm,vexpress-osc";
 			arm,vexpress-sysreg,func = <1 3>;
@@ -289,7 +289,7 @@
 			clock-output-names = "oscclk3";
 		};
 
-		oscclk4 {
+		clock-controller-4 {
 			/* External AXI master clock */
 			compatible = "arm,vexpress-osc";
 			arm,vexpress-sysreg,func = <1 4>;
@@ -298,7 +298,7 @@
 			clock-output-names = "oscclk4";
 		};
 
-		hdlcd_clk: oscclk5 {
+		hdlcd_clk: clock-controller-5 {
 			/* HDLCD PLL reference clock */
 			compatible = "arm,vexpress-osc";
 			arm,vexpress-sysreg,func = <1 5>;
@@ -307,7 +307,7 @@
 			clock-output-names = "oscclk5";
 		};
 
-		smbclk: oscclk6 {
+		smbclk: clock-controller-6 {
 			/* Static memory controller clock */
 			compatible = "arm,vexpress-osc";
 			arm,vexpress-sysreg,func = <1 6>;
@@ -316,7 +316,7 @@
 			clock-output-names = "oscclk6";
 		};
 
-		oscclk7 {
+		clock-controller-7 {
 			/* SYS PLL reference clock */
 			compatible = "arm,vexpress-osc";
 			arm,vexpress-sysreg,func = <1 7>;
@@ -325,7 +325,7 @@
 			clock-output-names = "oscclk7";
 		};
 
-		oscclk8 {
+		clock-controller-8 {
 			/* DDR2 PLL reference clock */
 			compatible = "arm,vexpress-osc";
 			arm,vexpress-sysreg,func = <1 8>;
@@ -334,7 +334,7 @@
 			clock-output-names = "oscclk8";
 		};
 
-		volt-a15 {
+		regulator-a15 {
 			/* A15 CPU core voltage */
 			compatible = "arm,vexpress-volt";
 			arm,vexpress-sysreg,func = <2 0>;
@@ -345,7 +345,7 @@
 			label = "A15 Vcore";
 		};
 
-		volt-a7 {
+		regulator-a7 {
 			/* A7 CPU core voltage */
 			compatible = "arm,vexpress-volt";
 			arm,vexpress-sysreg,func = <2 1>;
diff --git a/arch/arm/boot/dts/vexpress-v2p-ca5s.dts b/arch/arm/boot/dts/arm/vexpress-v2p-ca5s.dts
index 3b88209bacea..e3896253f33e 100644
--- a/arch/arm/boot/dts/vexpress-v2p-ca5s.dts
+++ b/arch/arm/boot/dts/arm/vexpress-v2p-ca5s.dts
@@ -132,6 +132,7 @@
 		reg = <0x2c0f0000 0x1000>;
 		interrupts = <0 84 4>;
 		cache-level = <2>;
+		cache-unified;
 	};
 
 	pmu {
@@ -144,7 +145,7 @@
 		compatible = "arm,vexpress,config-bus";
 		arm,vexpress,config-bridge = <&v2m_sysreg>;
 
-		cpu_clk: oscclk0 {
+		cpu_clk: clock-controller-0 {
 			/* CPU and internal AXI reference clock */
 			compatible = "arm,vexpress-osc";
 			arm,vexpress-sysreg,func = <1 0>;
@@ -153,7 +154,7 @@
 			clock-output-names = "oscclk0";
 		};
 
-		axi_clk: oscclk1 {
+		axi_clk: clock-controller-1 {
 			/* Multiplexed AXI master clock */
 			compatible = "arm,vexpress-osc";
 			arm,vexpress-sysreg,func = <1 1>;
@@ -162,7 +163,7 @@
 			clock-output-names = "oscclk1";
 		};
 
-		oscclk2 {
+		clock-controller-2 {
 			/* DDR2 */
 			compatible = "arm,vexpress-osc";
 			arm,vexpress-sysreg,func = <1 2>;
@@ -171,7 +172,7 @@
 			clock-output-names = "oscclk2";
 		};
 
-		hdlcd_clk: oscclk3 {
+		hdlcd_clk: clock-controller-3 {
 			/* HDLCD */
 			compatible = "arm,vexpress-osc";
 			arm,vexpress-sysreg,func = <1 3>;
@@ -180,7 +181,7 @@
 			clock-output-names = "oscclk3";
 		};
 
-		oscclk4 {
+		clock-controller-4 {
 			/* Test chip gate configuration */
 			compatible = "arm,vexpress-osc";
 			arm,vexpress-sysreg,func = <1 4>;
@@ -189,7 +190,7 @@
 			clock-output-names = "oscclk4";
 		};
 
-		smbclk: oscclk5 {
+		smbclk: clock-controller-5 {
 			/* SMB clock */
 			compatible = "arm,vexpress-osc";
 			arm,vexpress-sysreg,func = <1 5>;
diff --git a/arch/arm/boot/dts/vexpress-v2p-ca9.dts b/arch/arm/boot/dts/arm/vexpress-v2p-ca9.dts
index 5916e4877eac..43a5a4ab6ff0 100644
--- a/arch/arm/boot/dts/vexpress-v2p-ca9.dts
+++ b/arch/arm/boot/dts/arm/vexpress-v2p-ca9.dts
@@ -20,7 +20,9 @@
 	#address-cells = <1>;
 	#size-cells = <1>;
 
-	chosen { };
+	chosen {
+		stdout-path = &v2m_serial0;
+	};
 
 	aliases {
 		serial0 = &v2m_serial0;
@@ -185,7 +187,7 @@
 		compatible = "arm,vexpress,config-bus";
 		arm,vexpress,config-bridge = <&v2m_sysreg>;
 
-		oscclk0: extsaxiclk {
+		oscclk0: clock-controller-0 {
 			/* ACLK clock to the AXI master port on the test chip */
 			compatible = "arm,vexpress-osc";
 			arm,vexpress-sysreg,func = <1 0>;
@@ -194,7 +196,7 @@
 			clock-output-names = "extsaxiclk";
 		};
 
-		oscclk1: clcdclk {
+		oscclk1: clock-controller-1 {
 			/* Reference clock for the CLCD */
 			compatible = "arm,vexpress-osc";
 			arm,vexpress-sysreg,func = <1 1>;
@@ -203,7 +205,7 @@
 			clock-output-names = "clcdclk";
 		};
 
-		smbclk: oscclk2: tcrefclk {
+		smbclk: oscclk2: clock-controller-2 {
 			/* Reference clock for the test chip internal PLLs */
 			compatible = "arm,vexpress-osc";
 			arm,vexpress-sysreg,func = <1 2>;
@@ -212,7 +214,7 @@
 			clock-output-names = "tcrefclk";
 		};
 
-		volt-vd10 {
+		regulator-vd10 {
 			/* Test Chip internal logic voltage */
 			compatible = "arm,vexpress-volt";
 			arm,vexpress-sysreg,func = <2 0>;
@@ -221,7 +223,7 @@
 			label = "VD10";
 		};
 
-		volt-vd10-s2 {
+		regulator-vd10-s2 {
 			/* PL310, L2 cache, RAM cell supply (not PL310 logic) */
 			compatible = "arm,vexpress-volt";
 			arm,vexpress-sysreg,func = <2 1>;
@@ -230,7 +232,7 @@
 			label = "VD10_S2";
 		};
 
-		volt-vd10-s3 {
+		regulator-vd10-s3 {
 			/* Cortex-A9 system supply, Cores, MPEs, SCU and PL310 logic */
 			compatible = "arm,vexpress-volt";
 			arm,vexpress-sysreg,func = <2 2>;
@@ -239,7 +241,7 @@
 			label = "VD10_S3";
 		};
 
-		volt-vcc1v8 {
+		regulator-vcc1v8 {
 			/* DDR2 SDRAM and Test Chip DDR2 I/O supply */
 			compatible = "arm,vexpress-volt";
 			arm,vexpress-sysreg,func = <2 3>;
@@ -248,7 +250,7 @@
 			label = "VCC1V8";
 		};
 
-		volt-ddr2vtt {
+		regulator-ddr2vtt {
 			/* DDR2 SDRAM VTT termination voltage */
 			compatible = "arm,vexpress-volt";
 			arm,vexpress-sysreg,func = <2 4>;
@@ -257,7 +259,7 @@
 			label = "DDR2VTT";
 		};
 
-		volt-vcc3v3 {
+		regulator-vcc3v3 {
 			/* Local board supply for miscellaneous logic external to the Test Chip */
 			arm,vexpress-sysreg,func = <2 5>;
 			compatible = "arm,vexpress-volt";
diff --git a/arch/arm/boot/dts/aspeed-bmc-arm-centriq2400-rep.dts b/arch/arm/boot/dts/aspeed-bmc-arm-centriq2400-rep.dts
deleted file mode 100644
index 3395de96ee11..000000000000
--- a/arch/arm/boot/dts/aspeed-bmc-arm-centriq2400-rep.dts
+++ /dev/null
@@ -1,225 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/dts-v1/;
-
-#include "aspeed-g5.dtsi"
-#include <dt-bindings/gpio/aspeed-gpio.h>
-
-/ {
-	model = "Qualcomm Centriq 2400  REP AST2520";
-	compatible = "qualcomm,centriq2400-rep-bmc", "aspeed,ast2500";
-
-	chosen {
-		stdout-path = &uart5;
-		bootargs = "console=ttyS4,115200 earlycon";
-	};
-
-	memory@80000000 {
-		reg = <0x80000000 0x40000000>;
-	};
-
-	iio-hwmon {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
-                        <&adc 4>, <&adc 5>, <&adc 6>, <&adc 8>;
-	};
-
-	iio-hwmon-battery {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 7>;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		uid_led {
-			label = "UID_LED";
-			gpios = <&gpio ASPEED_GPIO(Q, 5) GPIO_ACTIVE_LOW>;
-		};
-
-		ras_error_led {
-			label = "RAS_ERROR_LED";
-			gpios = <&gpio ASPEED_GPIO(F, 6) GPIO_ACTIVE_LOW>;
-		};
-
-		system_fault {
-			label = "System_fault";
-			gpios = <&gpio ASPEED_GPIO(A, 1) GPIO_ACTIVE_LOW>;
-		};
-	};
-};
-
-&fmc {
-	status = "okay";
-	flash@0 {
-		status = "okay";
-		m25p,fast-read;
-		label = "bmc";
-#include "openbmc-flash-layout.dtsi"
-	};
-};
-
-&spi1 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_spi1_default>;
-	flash@0 {
-		status = "okay";
-	};
-};
-
-&spi2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_spi2ck_default
-			&pinctrl_spi2miso_default
-			&pinctrl_spi2mosi_default
-			&pinctrl_spi2cs0_default>;
-};
-
-&uart3 {
-	status = "okay";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_txd3_default &pinctrl_rxd3_default>;
-	current-speed = <115200>;
-};
-
-&uart5 {
-	status = "okay";
-};
-
-&mac0 {
-	status = "okay";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_rgmii1_default &pinctrl_mdio1_default>;
-};
-
-&i2c0 {
-	status = "okay";
-};
-
-&i2c1 {
-	status = "okay";
-
-	tmp421@1e {
-		compatible = "ti,tmp421";
-		reg = <0x1e>;
-	};
-	tmp421@2a {
-		compatible = "ti,tmp421";
-		reg = <0x2a>;
-	};
-	tmp421@4e {
-		compatible = "ti,tmp421";
-		reg = <0x4e>;
-	};
-	tmp421@1c {
-		compatible = "ti,tmp421";
-		reg = <0x1c>;
-	};
-};
-
-&i2c2 {
-	status = "okay";
-};
-
-&i2c3 {
-	status = "okay";
-};
-
-&i2c4 {
-	status = "okay";
-};
-
-&i2c5 {
-	status = "okay";
-};
-
-&i2c6 {
-	status = "okay";
-
-	tmp421@1d {
-		compatible = "ti,tmp421";
-		reg = <0x1d>;
-	};
-	tmp421@1f {
-		compatible = "ti,tmp421";
-		reg = <0x1f>;
-	};
-	tmp421@4d {
-		compatible = "ti,tmp421";
-		reg = <0x4d>;
-	};
-	tmp421@4f {
-		compatible = "ti,tmp421";
-		reg = <0x4f>;
-	};
-	nvt210@4c {
-		compatible = "nvt210";
-		reg = <0x4c>;
-	};
-	eeprom@50 {
-		compatible = "atmel,24c128";
-		reg = <0x50>;
-		pagesize = <128>;
-	};
-};
-
-&i2c7 {
-	status = "okay";
-};
-
-&i2c8 {
-	status = "okay";
-
-	pca9641@70 {
-		compatible = "nxp,pca9641";
-		reg = <0x70>;
-		i2c-arb {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			tmp421@1d {
-				compatible = "tmp421";
-				reg = <0x1d>;
-			};
-			adm1278@12 {
-				compatible = "adi,adm1278";
-				reg = <0x12>;
-				Rsense = <500>;
-			};
-			eeprom@50 {
-				compatible = "atmel,24c02";
-				reg = <0x50>;
-			};
-			ds1100@58 {
-				compatible = "ds1100";
-				reg = <0x58>;
-			};
-		};
-	};
-};
-
-&i2c9 {
-	status = "okay";
-};
-
-&vuart {
-	status = "okay";
-};
-
-&gfx {
-	status = "okay";
-};
-
-&pinctrl {
-	aspeed,external-nodes = <&gfx &lhc>;
-};
-
-&gpio {
-	pin_gpio_c7 {
-		gpio-hog;
-		gpios = <ASPEED_GPIO(C, 7) GPIO_ACTIVE_HIGH>;
-		output;
-		line-name = "BIOS_SPI_MUX_S";
-	};
-};
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-cloudripper.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-cloudripper.dts
deleted file mode 100644
index 9c6271a17ae8..000000000000
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-cloudripper.dts
+++ /dev/null
@@ -1,544 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-// Copyright (c) 2020 Facebook Inc.
-
-/dts-v1/;
-
-#include <dt-bindings/leds/common.h>
-#include "ast2600-facebook-netbmc-common.dtsi"
-
-/ {
-	model = "Facebook Cloudripper BMC";
-	compatible = "facebook,cloudripper-bmc", "aspeed,ast2600";
-
-	aliases {
-		/*
-		 * PCA9548 (1-0070) provides 8 channels connecting to
-		 * SMB (Switch Main Board).
-		 */
-		i2c16 = &imux16;
-		i2c17 = &imux17;
-		i2c18 = &imux18;
-		i2c19 = &imux19;
-		i2c20 = &imux20;
-		i2c21 = &imux21;
-		i2c22 = &imux22;
-		i2c23 = &imux23;
-
-		/*
-		 * PCA9548 (2-0070) provides 8 channels connecting to
-		 * SCM (System Controller Module).
-		 */
-		i2c24 = &imux24;
-		i2c25 = &imux25;
-		i2c26 = &imux26;
-		i2c27 = &imux27;
-		i2c28 = &imux28;
-		i2c29 = &imux29;
-		i2c30 = &imux30;
-		i2c31 = &imux31;
-
-		/*
-		 * PCA9548 (3-0070) provides 8 channels connecting to
-		 * SMB (Switch Main Board).
-		 */
-		i2c32 = &imux32;
-		i2c33 = &imux33;
-		i2c34 = &imux34;
-		i2c35 = &imux35;
-		i2c36 = &imux36;
-		i2c37 = &imux37;
-		i2c38 = &imux38;
-		i2c39 = &imux39;
-
-		/*
-		 * PCA9548 (8-0070) provides 8 channels connecting to
-		 * PDB (Power Delivery Board).
-		 */
-		i2c40 = &imux40;
-		i2c41 = &imux41;
-		i2c42 = &imux42;
-		i2c43 = &imux43;
-		i2c44 = &imux44;
-		i2c45 = &imux45;
-		i2c46 = &imux46;
-		i2c47 = &imux47;
-
-		/*
-		 * PCA9548 (15-0076) provides 8 channels connecting to
-		 * FCM (Fan Controller Module).
-		 */
-		i2c48 = &imux48;
-		i2c49 = &imux49;
-		i2c50 = &imux50;
-		i2c51 = &imux51;
-		i2c52 = &imux52;
-		i2c53 = &imux53;
-		i2c54 = &imux54;
-		i2c55 = &imux55;
-	};
-
-	spi_gpio: spi-gpio {
-		num-chipselects = <2>;
-		cs-gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>,
-			   <&gpio0 ASPEED_GPIO(X, 1) GPIO_ACTIVE_HIGH>;
-
-		eeprom@1 {
-			compatible = "atmel,at93c46d";
-			spi-max-frequency = <250000>;
-			data-size = <16>;
-			spi-cs-high;
-			reg = <1>;
-		};
-	};
-};
-
-&ehci1 {
-	status = "okay";
-};
-
-/*
- * "mdio1" is connected to the MDC/MDIO interface of the on-board
- * management switch (whose ports are connected to BMC, Host and front
- * panel ethernet port).
- */
-&mdio1 {
-	status = "okay";
-};
-
-&mdio3 {
-	status = "okay";
-
-	ethphy1: ethernet-phy@13 {
-		compatible = "ethernet-phy-ieee802.3-c22";
-		reg = <0x0d>;
-	};
-};
-
-&mac3 {
-	status = "okay";
-	phy-mode = "rgmii";
-	phy-handle = <&ethphy1>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_rgmii4_default>;
-};
-
-&i2c0 {
-	multi-master;
-	bus-frequency = <1000000>;
-};
-
-&i2c1 {
-	/*
-	 * PCA9548 (1-0070) provides 8 channels connecting to SMB (Switch
-	 * Main Board).
-	 */
-	i2c-switch@70 {
-		compatible = "nxp,pca9548";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x70>;
-		i2c-mux-idle-disconnect;
-
-		imux16: i2c@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-		};
-
-		imux17: i2c@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <1>;
-		};
-
-		imux18: i2c@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <2>;
-		};
-
-		imux19: i2c@3 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <3>;
-		};
-
-		imux20: i2c@4 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <4>;
-		};
-
-		imux21: i2c@5 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <5>;
-		};
-
-		imux22: i2c@6 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <6>;
-		};
-
-		imux23: i2c@7 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <7>;
-		};
-	};
-};
-
-&i2c2 {
-	/*
-	 * PCA9548 (2-0070) provides 8 channels connecting to SCM (System
-	 * Controller Module).
-	 */
-	i2c-switch@70 {
-		compatible = "nxp,pca9548";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x70>;
-		i2c-mux-idle-disconnect;
-
-		imux24: i2c@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-		};
-
-		imux25: i2c@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <1>;
-		};
-
-		imux26: i2c@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <2>;
-		};
-
-		imux27: i2c@3 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <3>;
-		};
-
-		imux28: i2c@4 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <4>;
-		};
-
-		imux29: i2c@5 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <5>;
-		};
-
-		imux30: i2c@6 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <6>;
-		};
-
-		imux31: i2c@7 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <7>;
-		};
-	};
-};
-
-&i2c3 {
-	/*
-	 * PCA9548 (3-0070) provides 8 channels connecting to SMB (Switch
-	 * Main Board).
-	 */
-	i2c-switch@70 {
-		compatible = "nxp,pca9548";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x70>;
-		i2c-mux-idle-disconnect;
-
-		imux32: i2c@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-		};
-
-		imux33: i2c@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <1>;
-		};
-
-		imux34: i2c@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <2>;
-		};
-
-		imux35: i2c@3 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <3>;
-		};
-
-		imux36: i2c@4 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <4>;
-		};
-
-		imux37: i2c@5 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <5>;
-		};
-
-		imux38: i2c@6 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <6>;
-		};
-
-		imux39: i2c@7 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <7>;
-		};
-	};
-};
-
-&i2c6 {
-	lp5012@14 {
-		compatible = "ti,lp5012";
-		reg = <0x14>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		multi-led@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-			color = <LED_COLOR_ID_MULTI>;
-			function = LED_FUNCTION_ACTIVITY;
-			label = "sys";
-
-			led@0 {
-				reg = <0>;
-				color = <LED_COLOR_ID_RED>;
-			};
-
-			led@1 {
-				reg = <1>;
-				color = <LED_COLOR_ID_BLUE>;
-			};
-
-			led@2 {
-				reg = <2>;
-				color = <LED_COLOR_ID_GREEN>;
-			};
-		};
-
-		multi-led@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <1>;
-			color = <LED_COLOR_ID_MULTI>;
-			function = LED_FUNCTION_ACTIVITY;
-			label = "fan";
-
-			led@0 {
-				reg = <0>;
-				color = <LED_COLOR_ID_RED>;
-			};
-
-			led@1 {
-				reg = <1>;
-				color = <LED_COLOR_ID_BLUE>;
-			};
-
-			led@2 {
-				reg = <2>;
-				color = <LED_COLOR_ID_GREEN>;
-			};
-		};
-
-		multi-led@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <2>;
-			color = <LED_COLOR_ID_MULTI>;
-			function = LED_FUNCTION_ACTIVITY;
-			label = "psu";
-
-			led@0 {
-				reg = <0>;
-				color = <LED_COLOR_ID_RED>;
-			};
-
-			led@1 {
-				reg = <1>;
-				color = <LED_COLOR_ID_BLUE>;
-			};
-
-			led@2 {
-				reg = <2>;
-				color = <LED_COLOR_ID_GREEN>;
-			};
-		};
-
-		multi-led@3 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <3>;
-			color = <LED_COLOR_ID_MULTI>;
-			function = LED_FUNCTION_ACTIVITY;
-			label = "scm";
-
-			led@0 {
-				reg = <0>;
-				color = <LED_COLOR_ID_RED>;
-			};
-
-			led@1 {
-				reg = <1>;
-				color = <LED_COLOR_ID_BLUE>;
-			};
-
-			led@2 {
-				reg = <2>;
-				color = <LED_COLOR_ID_GREEN>;
-			};
-		};
-	};
-};
-
-&i2c8 {
-	/*
-	 * PCA9548 (8-0070) provides 8 channels connecting to PDB (Power
-	 * Delivery Board).
-	 */
-	i2c-switch@70 {
-		compatible = "nxp,pca9548";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x70>;
-		i2c-mux-idle-disconnect;
-
-		imux40: i2c@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-		};
-
-		imux41: i2c@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <1>;
-		};
-
-		imux42: i2c@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <2>;
-		};
-
-		imux43: i2c@3 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <3>;
-		};
-
-		imux44: i2c@4 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <4>;
-		};
-
-		imux45: i2c@5 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <5>;
-		};
-
-		imux46: i2c@6 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <6>;
-		};
-
-		imux47: i2c@7 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <7>;
-		};
-
-	};
-};
-
-&i2c15 {
-	/*
-	 * PCA9548 (15-0076) provides 8 channels connecting to FCM (Fan
-	 * Controller Module).
-	 */
-	i2c-switch@76 {
-		compatible = "nxp,pca9548";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x76>;
-		i2c-mux-idle-disconnect;
-
-		imux48: i2c@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-		};
-
-		imux49: i2c@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <1>;
-		};
-
-		imux50: i2c@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <2>;
-		};
-
-		imux51: i2c@3 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <3>;
-		};
-
-		imux52: i2c@4 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <4>;
-		};
-
-		imux53: i2c@5 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <5>;
-		};
-
-		imux54: i2c@6 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <6>;
-		};
-
-		imux55: i2c@7 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <7>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-mihawk.dts b/arch/arm/boot/dts/aspeed-bmc-opp-mihawk.dts
deleted file mode 100644
index a52a289cee85..000000000000
--- a/arch/arm/boot/dts/aspeed-bmc-opp-mihawk.dts
+++ /dev/null
@@ -1,1380 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/dts-v1/;
-#include "aspeed-g5.dtsi"
-#include <dt-bindings/gpio/aspeed-gpio.h>
-#include <dt-bindings/leds/leds-pca955x.h>
-
-/ {
-	model = "Mihawk BMC";
-	compatible = "ibm,mihawk-bmc", "aspeed,ast2500";
-
-	aliases {
-		i2c215 = &bus6_mux215;
-		i2c216 = &bus6_mux216;
-		i2c217 = &bus6_mux217;
-		i2c218 = &bus6_mux218;
-		i2c219 = &bus6_mux219;
-		i2c220 = &bus6_mux220;
-		i2c221 = &bus6_mux221;
-		i2c222 = &bus6_mux222;
-		i2c223 = &bus7_mux223;
-		i2c224 = &bus7_mux224;
-		i2c225 = &bus7_mux225;
-		i2c226 = &bus7_mux226;
-		i2c227 = &bus7_mux227;
-		i2c228 = &bus7_mux228;
-		i2c229 = &bus7_mux229;
-		i2c230 = &bus7_mux230;
-		i2c231 = &bus9_mux231;
-		i2c232 = &bus9_mux232;
-		i2c233 = &bus9_mux233;
-		i2c234 = &bus9_mux234;
-		i2c235 = &bus9_mux235;
-		i2c236 = &bus9_mux236;
-		i2c237 = &bus9_mux237;
-		i2c238 = &bus9_mux238;
-		i2c239 = &bus10_mux239;
-		i2c240 = &bus10_mux240;
-		i2c241 = &bus10_mux241;
-		i2c242 = &bus10_mux242;
-		i2c243 = &bus10_mux243;
-		i2c244 = &bus10_mux244;
-		i2c245 = &bus10_mux245;
-		i2c246 = &bus10_mux246;
-		i2c247 = &bus12_mux247;
-		i2c248 = &bus12_mux248;
-		i2c249 = &bus12_mux249;
-		i2c250 = &bus12_mux250;
-		i2c251 = &bus13_mux251;
-		i2c252 = &bus13_mux252;
-		i2c253 = &bus13_mux253;
-		i2c254 = &bus13_mux254;
-		i2c255 = &bus13_mux255;
-		i2c256 = &bus13_mux256;
-		i2c257 = &bus13_mux257;
-		i2c258 = &bus13_mux258;
-	};
-
-	chosen {
-		stdout-path = &uart5;
-		bootargs = "console=ttyS4,115200 earlycon";
-	};
-
-	memory@80000000 {
-		reg = <0x80000000 0x20000000>;
-	};
-
-	reserved-memory {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		flash_memory: region@98000000 {
-			no-map;
-			reg = <0x98000000 0x04000000>; /* 64M */
-		};
-
-		gfx_memory: framebuffer {
-			size = <0x01000000>;
-			alignment = <0x01000000>;
-			compatible = "shared-dma-pool";
-			reusable;
-		};
-
-		video_engine_memory: jpegbuffer {
-			size = <0x02000000>;
-			alignment = <0x01000000>;
-			compatible = "shared-dma-pool";
-			reusable;
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		air-water {
-			label = "air-water";
-			gpios = <&gpio ASPEED_GPIO(F, 6) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(F, 6)>;
-		};
-
-		checkstop {
-			label = "checkstop";
-			gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(J, 2)>;
-		};
-
-		ps0-presence {
-			label = "ps0-presence";
-			gpios = <&gpio ASPEED_GPIO(Z, 2) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(Z, 2)>;
-		};
-
-		ps1-presence {
-			label = "ps1-presence";
-			gpios = <&gpio ASPEED_GPIO(Z, 0) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(Z, 0)>;
-		};
-		id-button {
-			label = "id-button";
-			gpios = <&gpio ASPEED_GPIO(F, 1) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(F, 1)>;
-		};
-	};
-
-	gpio-keys-polled {
-		compatible = "gpio-keys-polled";
-		poll-interval = <1000>;
-
-		fan0-presence {
-			label = "fan0-presence";
-			gpios = <&pca9552 9 GPIO_ACTIVE_LOW>;
-			linux,code = <9>;
-		};
-
-		fan1-presence {
-			label = "fan1-presence";
-			gpios = <&pca9552 10 GPIO_ACTIVE_LOW>;
-			linux,code = <10>;
-		};
-
-		fan2-presence {
-			label = "fan2-presence";
-			gpios = <&pca9552 11 GPIO_ACTIVE_LOW>;
-			linux,code = <11>;
-		};
-
-		fan3-presence {
-			label = "fan3-presence";
-			gpios = <&pca9552 12 GPIO_ACTIVE_LOW>;
-			linux,code = <12>;
-		};
-
-		fan4-presence {
-			label = "fan4-presence";
-			gpios = <&pca9552 13 GPIO_ACTIVE_LOW>;
-			linux,code = <13>;
-		};
-
-		fan5-presence {
-			label = "fan5-presence";
-			gpios = <&pca9552 14 GPIO_ACTIVE_LOW>;
-			linux,code = <14>;
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		front-fault {
-			retain-state-shutdown;
-			default-state = "keep";
-			gpios = <&gpio ASPEED_GPIO(AA, 0) GPIO_ACTIVE_LOW>;
-		};
-
-		power-button {
-			retain-state-shutdown;
-			default-state = "keep";
-			gpios = <&gpio ASPEED_GPIO(AA, 1) GPIO_ACTIVE_LOW>;
-		};
-
-		front-id {
-			retain-state-shutdown;
-			default-state = "keep";
-			gpios = <&gpio ASPEED_GPIO(AA, 2) GPIO_ACTIVE_LOW>;
-		};
-
-
-		fan0 {
-			retain-state-shutdown;
-			default-state = "keep";
-			gpios = <&pca9552 0 GPIO_ACTIVE_LOW>;
-		};
-
-		fan1 {
-			retain-state-shutdown;
-			default-state = "keep";
-			gpios = <&pca9552 1 GPIO_ACTIVE_LOW>;
-		};
-
-		fan2 {
-			retain-state-shutdown;
-			default-state = "keep";
-			gpios = <&pca9552 2 GPIO_ACTIVE_LOW>;
-		};
-
-		fan3 {
-			retain-state-shutdown;
-			default-state = "keep";
-			gpios = <&pca9552 3 GPIO_ACTIVE_LOW>;
-		};
-
-		fan4 {
-			retain-state-shutdown;
-			default-state = "keep";
-			gpios = <&pca9552 4 GPIO_ACTIVE_LOW>;
-		};
-
-		fan5 {
-			retain-state-shutdown;
-			default-state = "keep";
-			gpios = <&pca9552 5 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	fsi: gpio-fsi {
-		compatible = "fsi-master-gpio", "fsi-master";
-		#address-cells = <2>;
-		#size-cells = <0>;
-		no-gpio-delays;
-
-		clock-gpios = <&gpio ASPEED_GPIO(E, 6) GPIO_ACTIVE_HIGH>;
-		data-gpios = <&gpio ASPEED_GPIO(E, 7) GPIO_ACTIVE_HIGH>;
-		mux-gpios = <&gpio ASPEED_GPIO(E, 5) GPIO_ACTIVE_HIGH>;
-		enable-gpios = <&gpio ASPEED_GPIO(D, 0) GPIO_ACTIVE_HIGH>;
-		trans-gpios = <&gpio ASPEED_GPIO(R, 2) GPIO_ACTIVE_HIGH>;
-	};
-	iio-hwmon-12v {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 0>;
-	};
-
-	iio-hwmon-5v {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 1>;
-	};
-
-	iio-hwmon-3v {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 2>;
-	};
-
-	iio-hwmon-vdd0 {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 3>;
-	};
-
-	iio-hwmon-vdd1 {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 4>;
-	};
-
-	iio-hwmon-vcs0 {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 5>;
-	};
-
-	iio-hwmon-vcs1 {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 6>;
-	};
-
-	iio-hwmon-vdn0 {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 7>;
-	};
-
-	iio-hwmon-vdn1 {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 8>;
-	};
-
-	iio-hwmon-vio0 {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 9>;
-	};
-
-	iio-hwmon-vio1 {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 10>;
-	};
-
-	iio-hwmon-vddra {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 11>;
-	};
-
-	iio-hwmon-battery {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 12>;
-	};
-
-	iio-hwmon-vddrb {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 13>;
-	};
-
-	iio-hwmon-vddrc {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 14>;
-	};
-
-	iio-hwmon-vddrd {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 15>;
-	};
-};
-
-&pwm_tacho {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default
-		&pinctrl_pwm2_default &pinctrl_pwm3_default
-		&pinctrl_pwm4_default &pinctrl_pwm5_default>;
-
-	fan@0 {
-		reg = <0x00>;
-		aspeed,fan-tach-ch = /bits/ 8 <0x00>;
-	};
-
-	fan@1 {
-		reg = <0x01>;
-		aspeed,fan-tach-ch = /bits/ 8 <0x01>;
-	};
-
-	fan@2 {
-		reg = <0x02>;
-		aspeed,fan-tach-ch = /bits/ 8 <0x02>;
-	};
-
-	fan@3 {
-		reg = <0x03>;
-		aspeed,fan-tach-ch = /bits/ 8 <0x03>;
-	};
-
-	fan@4 {
-		reg = <0x04>;
-		aspeed,fan-tach-ch = /bits/ 8 <0x04>;
-	};
-
-	fan@5 {
-		reg = <0x05>;
-		aspeed,fan-tach-ch = /bits/ 8 <0x05>;
-	};
-
-	fan@6 {
-		reg = <0x00>;
-		aspeed,fan-tach-ch = /bits/ 8 <0x06>;
-	};
-
-	fan@7 {
-		reg = <0x01>;
-		aspeed,fan-tach-ch = /bits/ 8 <0x07>;
-	};
-
-	fan@8 {
-		reg = <0x02>;
-		aspeed,fan-tach-ch = /bits/ 8 <0x08>;
-	};
-
-	fan@9 {
-		reg = <0x03>;
-		aspeed,fan-tach-ch = /bits/ 8 <0x09>;
-	};
-
-	fan@10 {
-		reg = <0x04>;
-		aspeed,fan-tach-ch = /bits/ 8 <0x0a>;
-	};
-
-	fan@11 {
-		reg = <0x05>;
-		aspeed,fan-tach-ch = /bits/ 8 <0x0b>;
-	};
-};
-
-&gpio {
-	gpio-line-names =
-	/*A0-A7*/	"","cfam-reset","","","","","","",
-	/*B0-B7*/	"","","","","","","","",
-	/*C0-C7*/	"","","","","","","","",
-	/*D0-D7*/	"fsi-enable","","","","","","","",
-	/*E0-E7*/	"","","","","","fsi-mux","fsi-clock","fsi-data",
-	/*F0-F7*/	"","id-button","","","","","air-water","",
-	/*G0-G7*/	"","","","","","","","",
-	/*H0-H7*/	"","","","","","","","",
-	/*I0-I7*/	"","","","","","","","",
-	/*J0-J7*/	"","","checkstop","","","","","",
-	/*K0-K7*/	"","","","","","","","",
-	/*L0-L7*/	"","","","","","","","",
-	/*M0-M7*/	"","","","","","","","",
-	/*N0-N7*/	"","","","","","","","",
-	/*O0-O7*/	"","","","","","","","",
-	/*P0-P7*/	"","","","","","","","",
-	/*Q0-Q7*/	"","","","","","","","",
-	/*R0-R7*/	"","","fsi-trans","","","","","",
-	/*S0-S7*/	"","","","","","","","",
-	/*T0-T7*/	"","","","","","","","",
-	/*U0-U7*/	"","","","","","","","",
-	/*V0-V7*/	"","","","","","","","",
-	/*W0-W7*/	"","","","","","","","",
-	/*X0-X7*/	"","","","","","","","",
-	/*Y0-Y7*/	"","","","","","","","",
-	/*Z0-Z7*/	"presence-ps1","","presence-ps0","","","","","",
-	/*AA0-AA7*/	"led-front-fault","power-button","led-front-id","","","","","",
-	/*AB0-AB7*/	"","","","","","","","",
-	/*AC0-AC7*/	"","","","","","","","";
-};
-
-&fmc {
-	status = "okay";
-	flash@0 {
-		status = "okay";
-		label = "bmc";
-		m25p,fast-read;
-		spi-max-frequency = <50000000>;
-		partitions {
-			#address-cells = < 1 >;
-			#size-cells = < 1 >;
-			compatible = "fixed-partitions";
-			u-boot@0 {
-				reg = < 0 0x60000 >;
-				label = "u-boot";
-			};
-			u-boot-env@60000 {
-				reg = < 0x60000 0x20000 >;
-				label = "u-boot-env";
-			};
-			obmc-ubi@80000 {
-				reg = < 0x80000 0x1F80000 >;
-				label = "obmc-ubi";
-			};
-		};
-	};
-	flash@1 {
-		status = "okay";
-		label = "alt-bmc";
-		m25p,fast-read;
-		spi-max-frequency = <50000000>;
-		partitions {
-			#address-cells = < 1 >;
-			#size-cells = < 1 >;
-			compatible = "fixed-partitions";
-			u-boot@0 {
-				reg = < 0 0x60000 >;
-				label = "alt-u-boot";
-			};
-			u-boot-env@60000 {
-				reg = < 0x60000 0x20000 >;
-				label = "alt-u-boot-env";
-			};
-			obmc-ubi@80000 {
-				reg = < 0x80000 0x1F80000 >;
-				label = "alt-obmc-ubi";
-			};
-		};
-	};
-};
-
-&spi1 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_spi1_default>;
-
-	flash@0 {
-		status = "okay";
-		label = "pnor";
-		m25p,fast-read;
-		spi-max-frequency = <100000000>;
-	};
-};
-
-&lpc_ctrl {
-	status = "okay";
-	memory-region = <&flash_memory>;
-	flash = <&spi1>;
-};
-
-&uart1 {
-	/* Rear RS-232 connector */
-	status = "okay";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_txd1_default
-			&pinctrl_rxd1_default
-			&pinctrl_nrts1_default
-			&pinctrl_ndtr1_default
-			&pinctrl_ndsr1_default
-			&pinctrl_ncts1_default
-			&pinctrl_ndcd1_default
-			&pinctrl_nri1_default>;
-};
-
-&uart2 {
-	/* APSS */
-	status = "okay";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_txd2_default &pinctrl_rxd2_default>;
-};
-
-&uart5 {
-	status = "okay";
-};
-
-&mac0 {
-	status = "okay";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_rmii1_default>;
-	clocks = <&syscon ASPEED_CLK_GATE_MAC1CLK>,
-		 <&syscon ASPEED_CLK_MAC1RCLK>;
-	clock-names = "MACCLK", "RCLK";
-	use-ncsi;
-};
-
-&mac1 {
-	status = "okay";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
-};
-
-&i2c0 {
-	status = "disabled";
-};
-
-&i2c1 {
-	status = "disabled";
-};
-
-&i2c2 {
-	status = "okay";
-
-	/* SAMTEC P0 */
-	/* SAMTEC P1 */
-
-};
-
-&i2c3 {
-	status = "okay";
-
-	/* APSS */
-	/* CPLD */
-
-	/* PCA9516 (repeater) ->
-	 *    CLK Buffer 9FGS9092
-	 *    CLK Buffer 9DBL0651BKILFT
-	 *    CLK Buffer 9DBL0651BKILFT
-	 *    Power Supply 0
-	 *    Power Supply 1
-	 *    PCA 9552 LED
-	 */
-
-	power-supply@58 {
-		compatible = "ibm,cffps1";
-		reg = <0x58>;
-	};
-
-	power-supply@5b {
-		compatible = "ibm,cffps1";
-		reg = <0x5b>;
-	};
-
-	pca9552: pca9552@60 {
-		compatible = "nxp,pca9552";
-		reg = <0x60>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		gpio@0 {
-			reg = <0>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-		gpio@1 {
-			reg = <1>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-		gpio@2 {
-			reg = <2>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-		gpio@3 {
-			reg = <3>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-		gpio@4 {
-			reg = <4>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-		gpio@5 {
-			reg = <5>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-		gpio@6 {
-			reg = <6>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-		gpio@7 {
-			reg = <7>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-		gpio@8 {
-			reg = <8>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-		gpio@9 {
-			reg = <9>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-		gpio@10 {
-			reg = <10>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-		gpio@11 {
-			reg = <11>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-		gpio@12 {
-			reg = <12>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-		gpio@13 {
-			reg = <13>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-		gpio@14 {
-			reg = <14>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-		gpio@15 {
-			reg = <15>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-	};
-
-};
-
-&i2c4 {
-	status = "okay";
-
-	/* CP0 VDD & VCS : IR35221 */
-	/* CP0 VDN : IR35221 */
-	/* CP0 VIO : IR38064 */
-	/* CP0 VDDR : PXM1330 */
-
-	ir35221@70 {
-		compatible = "infineon,ir35221";
-		reg = <0x70>;
-	};
-
-	ir35221@72 {
-		compatible = "infineon,ir35221";
-		reg = <0x72>;
-	};
-
-};
-
-&i2c5 {
-	status = "okay";
-
-	/* CP0 VDD & VCS : IR35221 */
-	/* CP0 VDN : IR35221 */
-	/* CP0 VIO : IR38064 */
-	/* CP0 VDDR : PXM1330 */
-
-	ir35221@70 {
-		compatible = "infineon,ir35221";
-		reg = <0x70>;
-	};
-
-	ir35221@72 {
-		compatible = "infineon,ir35221";
-		reg = <0x72>;
-	};
-
-};
-
-&i2c6 {
-	status = "okay";
-
-	/* pca9548 -> NVMe1 to 8 */
-
-	pca9548@70 {
-		compatible = "nxp,pca9548";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x70>;
-
-		bus7_mux223: i2c@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-		};
-
-		bus7_mux224: i2c@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <1>;
-		};
-
-		bus7_mux225: i2c@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <2>;
-		};
-
-		bus7_mux226: i2c@3 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <3>;
-		};
-
-		bus7_mux227: i2c@4 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <4>;
-		};
-
-		bus7_mux228: i2c@5 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <5>;
-		};
-
-		bus7_mux229: i2c@6 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <6>;
-		};
-
-		bus7_mux230: i2c@7 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <7>;
-		};
-	};
-
-};
-
-&i2c7 {
-	status = "okay";
-
-	/* pca9548 -> NVMe9 to 16 */
-
-	pca9548@70 {
-		compatible = "nxp,pca9548";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x70>;
-
-		bus6_mux215: i2c@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-		};
-
-		bus6_mux216: i2c@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <1>;
-		};
-
-		bus6_mux217: i2c@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <2>;
-		};
-
-		bus6_mux218: i2c@3 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <3>;
-		};
-
-		bus6_mux219: i2c@4 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <4>;
-		};
-
-		bus6_mux220: i2c@5 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <5>;
-		};
-
-		bus6_mux221: i2c@6 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <6>;
-		};
-
-		bus6_mux222: i2c@7 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <7>;
-		};
-	};
-
-};
-
-&i2c8 {
-	status = "okay";
-
-	eeprom@50 {
-		compatible = "atmel,24c64";
-		reg = <0x50>;
-	};
-};
-
-&i2c9 {
-	status = "okay";
-
-	/* pca9545 Riser ->
-	*	PCIe x8  Slot3
-	*	PCIe x16 slot4
-	*	PCIe x8  slot5
-	*	I2C BMC RISER PCA9554
-	*	BMC SCL/SDA PCA9554
-	*	PCA9554
-	*/
-
-	/* pca9545 ->
-	*	PCIe x16 Slot1
-	*	PCIe x8  slot2
-	*	PEX8748
-	*/
-
-	pca9545riser@70 {
-		compatible = "nxp,pca9545";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x70>;
-
-		i2c-mux-idle-disconnect;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-
-		bus9_mux231: i2c@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-
-			tca9554@39 {
-				compatible = "ti,tca9554";
-				reg = <0x39>;
-				gpio-controller;
-				#gpio-cells = <2>;
-
-				smbus0-hog {
-					gpio-hog;
-					gpios = <4 GPIO_ACTIVE_HIGH>;
-					output-high;
-					line-name = "smbus0";
-				};
-			};
-
-			tmp431@4c {
-				compatible = "ti,tmp401";
-				reg = <0x4c>;
-			};
-		};
-
-		bus9_mux232: i2c@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <1>;
-
-			tca9554@39 {
-				compatible = "ti,tca9554";
-				reg = <0x39>;
-				gpio-controller;
-				#gpio-cells = <2>;
-
-				smbus1-hog {
-					gpio-hog;
-					gpios = <4 GPIO_ACTIVE_HIGH>;
-					output-high;
-					line-name = "smbus1";
-				};
-			};
-
-			tmp431@4c {
-				compatible = "ti,tmp401";
-				reg = <0x4c>;
-			};
-		};
-
-		bus9_mux233: i2c@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <2>;
-		};
-
-		bus9_mux234: i2c@3 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <3>;
-		};
-	};
-
-	pca9545@71 {
-		compatible = "nxp,pca9545";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x71>;
-
-		i2c-mux-idle-disconnect;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-
-		bus9_mux235: i2c@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-
-			tca9554@39 {
-				compatible = "ti,tca9554";
-				reg = <0x39>;
-				gpio-controller;
-				#gpio-cells = <2>;
-
-				smbus2-hog {
-					gpio-hog;
-					gpios = <4 GPIO_ACTIVE_HIGH>;
-					output-high;
-					line-name = "smbus2";
-				};
-			};
-
-			tmp431@4c {
-				compatible = "ti,tmp401";
-				reg = <0x4c>;
-			};
-		};
-
-		bus9_mux236: i2c@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <1>;
-
-			tca9554@39 {
-				compatible = "ti,tca9554";
-				reg = <0x39>;
-				gpio-controller;
-				#gpio-cells = <2>;
-
-				smbus3-hog {
-					gpio-hog;
-					gpios = <4 GPIO_ACTIVE_HIGH>;
-					output-high;
-					line-name = "smbus3";
-				};
-			};
-
-			tmp431@4c {
-				compatible = "ti,tmp401";
-				reg = <0x4c>;
-			};
-		};
-
-		bus9_mux237: i2c@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <2>;
-		};
-
-		bus9_mux238: i2c@3 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <3>;
-		};
-	};
-};
-
-&i2c10 {
-	status = "okay";
-
-	/* pca9545 Riser ->
-	* 	PCIe x8  Slot8
-	* 	PCIe x16 slot9
-	* 	PCIe x8  slot10
-	* 	I2C BMC RISER PCA9554
-	* 	BMC SCL/SDA PCA9554
-	* 	PCA9554
-	*/
-
-	/* pca9545 ->
-	*	PCIe x16 Slot1
-	*	PCIe x8  slot2
-	*	PEX8748
-	*/
-
-	pca9545riser@70 {
-		compatible = "nxp,pca9545";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x70>;
-
-		i2c-mux-idle-disconnect;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-
-		bus10_mux239: i2c@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-
-			tca9554@39 {
-				compatible = "ti,tca9554";
-				reg = <0x39>;
-				gpio-controller;
-				#gpio-cells = <2>;
-
-				smbus4-hog {
-					gpio-hog;
-					gpios = <4 GPIO_ACTIVE_HIGH>;
-					output-high;
-					line-name = "smbus4";
-				};
-			};
-
-			tmp431@4c {
-				compatible = "ti,tmp401";
-				reg = <0x4c>;
-			};
-		};
-
-		bus10_mux240: i2c@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <1>;
-
-			tca9554@39 {
-				compatible = "ti,tca9554";
-				reg = <0x39>;
-				gpio-controller;
-				#gpio-cells = <2>;
-
-				smbus5-hog {
-					gpio-hog;
-					gpios = <4 GPIO_ACTIVE_HIGH>;
-					output-high;
-					line-name = "smbus5";
-				};
-			};
-
-			tmp431@4c {
-				compatible = "ti,tmp401";
-				reg = <0x4c>;
-			};
-		};
-
-		bus10_mux241: i2c@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <2>;
-		};
-
-		bus10_mux242: i2c@3 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <3>;
-		};
-	};
-
-	pca9545@71 {
-		compatible = "nxp,pca9545";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x71>;
-
-		i2c-mux-idle-disconnect;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-
-		bus10_mux243: i2c@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-
-			tca9554@39 {
-				compatible = "ti,tca9554";
-				reg = <0x39>;
-				gpio-controller;
-				#gpio-cells = <2>;
-
-				smbus6-hog {
-					gpio-hog;
-					gpios = <4 GPIO_ACTIVE_HIGH>;
-					output-high;
-					line-name = "smbus6";
-				};
-			};
-
-			tmp431@4c {
-				compatible = "ti,tmp401";
-				reg = <0x4c>;
-			};
-		};
-
-		bus10_mux244: i2c@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <1>;
-
-			tca9554@39 {
-				compatible = "ti,tca9554";
-				reg = <0x39>;
-				gpio-controller;
-				#gpio-cells = <2>;
-
-				smbus7-hog {
-					gpio-hog;
-					gpios = <4 GPIO_ACTIVE_HIGH>;
-					output-high;
-					line-name = "smbus7";
-				};
-			};
-
-			tmp431@4c {
-				compatible = "ti,tmp401";
-				reg = <0x4c>;
-			};
-		};
-
-		bus10_mux245: i2c@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <2>;
-		};
-
-		bus10_mux246: i2c@3 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <3>;
-		};
-	};
-};
-
-&i2c11 {
-	status = "okay";
-
-	/* TPM */
-	/* RTC RX8900CE */
-	/* FPGA for power sequence */
-	/* TMP275A */
-	/* TMP275A */
-	/* EMC1462 */
-
-	tpm@57 {
-		compatible = "infineon,slb9645tt";
-		reg = <0x57>;
-	};
-
-	rtc@32 {
-		compatible = "epson,rx8900";
-		reg = <0x32>;
-	};
-
-	tmp275@48 {
-		compatible = "ti,tmp275";
-		reg = <0x48>;
-	};
-
-	tmp275@49 {
-		compatible = "ti,tmp275";
-		reg = <0x49>;
-	};
-
-	/* chip emc1462 use emc1403 driver */
-	emc1403@4c {
-		compatible = "smsc,emc1403";
-		reg = <0x4c>;
-	};
-
-};
-
-&i2c12 {
-	status = "okay";
-
-	/* pca9545 ->
-	*	SAS BP1
-	*	SAS BP2
-	*	NVMe BP
-	*	M.2 riser
-	*/
-
-	pca9545@70 {
-		compatible = "nxp,pca9545";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x70>;
-
-		interrupt-controller;
-		#interrupt-cells = <2>;
-
-		bus12_mux247: i2c@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-
-			eeprom@50 {
-				compatible = "atmel,24c64";
-				reg = <0x50>;
-			};
-		};
-
-		bus12_mux248: i2c@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <1>;
-
-			eeprom@50 {
-				compatible = "atmel,24c64";
-				reg = <0x50>;
-			};
-		};
-
-		bus12_mux249: i2c@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <2>;
-
-			eeprom@50 {
-				compatible = "atmel,24c64";
-				reg = <0x50>;
-			};
-		};
-
-		bus12_mux250: i2c@3 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <3>;
-
-			tmp275@48 {
-				compatible = "ti,tmp275";
-				reg = <0x48>;
-			};
-		};
-
-	};
-
-};
-
-&i2c13 {
-	status = "okay";
-
-	/* pca9548 ->
-	*	NVMe BP
-	*	NVMe HDD17 to 24
-	*/
-
-	pca9548@70 {
-		compatible = "nxp,pca9548";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x70>;
-		bus13_mux251: i2c@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-		};
-
-		bus13_mux252: i2c@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <1>;
-		};
-
-		bus13_mux253: i2c@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <2>;
-		};
-
-		bus13_mux254: i2c@3 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <3>;
-		};
-
-		bus13_mux255: i2c@4 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <4>;
-		};
-
-		bus13_mux256: i2c@5 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <5>;
-		};
-
-		bus13_mux257: i2c@6 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <6>;
-		};
-
-		bus13_mux258: i2c@7 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <7>;
-		};
-	};
-};
-
-&vuart {
-	status = "okay";
-};
-
-&gfx {
-	status = "okay";
-	memory-region = <&gfx_memory>;
-};
-
-&adc {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_adc0_default
-			&pinctrl_adc1_default
-			&pinctrl_adc2_default
-			&pinctrl_adc3_default
-			&pinctrl_adc4_default
-			&pinctrl_adc5_default
-			&pinctrl_adc6_default
-			&pinctrl_adc7_default
-			&pinctrl_adc8_default
-			&pinctrl_adc9_default
-			&pinctrl_adc10_default
-			&pinctrl_adc11_default
-			&pinctrl_adc12_default
-			&pinctrl_adc13_default
-			&pinctrl_adc14_default
-			&pinctrl_adc15_default>;
-};
-
-&wdt1 {
-	aspeed,reset-type = "none";
-	aspeed,external-signal;
-	aspeed,ext-push-pull;
-	aspeed,ext-active-high;
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_wdtrst1_default>;
-};
-
-&wdt2 {
-	aspeed,alt-boot;
-};
-
-&ibt {
-	status = "okay";
-};
-
-&vhub {
-	status = "okay";
-};
-
-&video {
-	status = "okay";
-	memory-region = <&video_engine_memory>;
-};
-
-#include "ibm-power9-dual.dtsi"
-
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-swift.dts b/arch/arm/boot/dts/aspeed-bmc-opp-swift.dts
deleted file mode 100644
index 4816486c0c9e..000000000000
--- a/arch/arm/boot/dts/aspeed-bmc-opp-swift.dts
+++ /dev/null
@@ -1,978 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/dts-v1/;
-#include "aspeed-g5.dtsi"
-#include <dt-bindings/gpio/aspeed-gpio.h>
-#include <dt-bindings/leds/leds-pca955x.h>
-
-/ {
-	model = "Swift BMC";
-	compatible = "ibm,swift-bmc", "aspeed,ast2500";
-
-	chosen {
-		stdout-path = &uart5;
-		bootargs = "console=ttyS4,115200 earlycon";
-	};
-
-	memory@80000000 {
-		reg = <0x80000000 0x20000000>;
-	};
-
-	reserved-memory {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		flash_memory: region@98000000 {
-			no-map;
-			reg = <0x98000000 0x04000000>; /* 64M */
-		};
-
-		gfx_memory: framebuffer {
-			size = <0x01000000>;
-			alignment = <0x01000000>;
-			compatible = "shared-dma-pool";
-			reusable;
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		air-water {
-			label = "air-water";
-			gpios = <&gpio ASPEED_GPIO(B, 5) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(B, 5)>;
-		};
-
-		checkstop {
-			label = "checkstop";
-			gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(J, 2)>;
-		};
-
-		ps0-presence {
-			label = "ps0-presence";
-			gpios = <&gpio ASPEED_GPIO(R, 7) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(R, 7)>;
-		};
-
-		ps1-presence {
-			label = "ps1-presence";
-			gpios = <&gpio ASPEED_GPIO(N, 0) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(N, 0)>;
-		};
-
-		oppanel-presence {
-			label = "oppanel-presence";
-			gpios = <&gpio ASPEED_GPIO(A, 7) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(A, 7)>;
-		};
-
-		opencapi-riser-presence {
-			label = "opencapi-riser-presence";
-			gpios = <&gpio ASPEED_GPIO(I, 0) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(I, 0)>;
-		};
-	};
-
-	iio-hwmon-battery {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 12>;
-	};
-
-	gpio-keys-polled {
-		compatible = "gpio-keys-polled";
-		poll-interval = <1000>;
-
-		scm0-presence {
-			label = "scm0-presence";
-			gpios = <&pca9552 6 GPIO_ACTIVE_LOW>;
-			linux,code = <6>;
-		};
-
-		scm1-presence {
-			label = "scm1-presence";
-			gpios = <&pca9552 7 GPIO_ACTIVE_LOW>;
-			linux,code = <7>;
-		};
-
-		cpu0vrm-presence {
-			label = "cpu0vrm-presence";
-			gpios = <&pca9552 12 GPIO_ACTIVE_LOW>;
-			linux,code = <12>;
-		};
-
-		cpu1vrm-presence {
-			label = "cpu1vrm-presence";
-			gpios = <&pca9552 13 GPIO_ACTIVE_LOW>;
-			linux,code = <13>;
-		};
-
-		fan0-presence {
-			label = "fan0-presence";
-			gpios = <&pca0 5 GPIO_ACTIVE_LOW>;
-			linux,code = <5>;
-		};
-
-		fan1-presence {
-			label = "fan1-presence";
-			gpios = <&pca0 6 GPIO_ACTIVE_LOW>;
-			linux,code = <6>;
-		};
-
-		fan2-presence {
-			label = "fan2-presence";
-			gpios = <&pca0 7 GPIO_ACTIVE_LOW>;
-			linux,code = <7>;
-		};
-
-		fan3-presence {
-			label = "fan3-presence";
-			gpios = <&pca0 8 GPIO_ACTIVE_LOW>;
-			linux,code = <8>;
-		};
-
-		fanboost-presence {
-			label = "fanboost-presence";
-			gpios = <&pca0 9 GPIO_ACTIVE_LOW>;
-			linux,code = <9>;
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		fan0 {
-			retain-state-shutdown;
-			default-state = "keep";
-			gpios = <&pca0 0 GPIO_ACTIVE_LOW>;
-		};
-
-		fan1 {
-			retain-state-shutdown;
-			default-state = "keep";
-			gpios = <&pca0 1 GPIO_ACTIVE_LOW>;
-		};
-
-		fan2 {
-			retain-state-shutdown;
-			default-state = "keep";
-			gpios = <&pca0 2 GPIO_ACTIVE_LOW>;
-		};
-
-		fan3 {
-			retain-state-shutdown;
-			default-state = "keep";
-			gpios = <&pca0 3 GPIO_ACTIVE_LOW>;
-		};
-
-		fanboost {
-			retain-state-shutdown;
-			default-state = "keep";
-			gpios = <&pca0 4 GPIO_ACTIVE_LOW>;
-		};
-
-		front-fault {
-			retain-state-shutdown;
-			default-state = "keep";
-			gpios = <&pca1 2 GPIO_ACTIVE_LOW>;
-		};
-
-		front-power {
-			retain-state-shutdown;
-			default-state = "keep";
-			gpios = <&pca1 3 GPIO_ACTIVE_LOW>;
-		};
-
-		front-id {
-			retain-state-shutdown;
-			default-state = "keep";
-			gpios = <&pca1 0 GPIO_ACTIVE_LOW>;
-		};
-
-		rear-fault {
-			gpios = <&gpio ASPEED_GPIO(N, 2) GPIO_ACTIVE_LOW>;
-		};
-
-		rear-id {
-			gpios = <&gpio ASPEED_GPIO(N, 4) GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	fsi: gpio-fsi {
-		compatible = "fsi-master-gpio", "fsi-master";
-		#address-cells = <2>;
-		#size-cells = <0>;
-		no-gpio-delays;
-
-		clock-gpios = <&gpio ASPEED_GPIO(P, 1) GPIO_ACTIVE_HIGH>;
-		data-gpios = <&gpio ASPEED_GPIO(P, 2) GPIO_ACTIVE_HIGH>;
-		mux-gpios = <&gpio ASPEED_GPIO(P, 4) GPIO_ACTIVE_HIGH>;
-		enable-gpios = <&gpio ASPEED_GPIO(P, 0) GPIO_ACTIVE_HIGH>;
-		trans-gpios = <&gpio ASPEED_GPIO(P, 3) GPIO_ACTIVE_HIGH>;
-	};
-
-	iio-hwmon-dps310 {
-		compatible = "iio-hwmon";
-		io-channels = <&dps 0>;
-	};
-
-};
-
-&fmc {
-	status = "okay";
-
-	flash@0 {
-		status = "okay";
-		label = "bmc";
-		m25p,fast-read;
-		spi-max-frequency = <100000000>;
-		partitions {
-			#address-cells = < 1 >;
-			#size-cells = < 1 >;
-			compatible = "fixed-partitions";
-			u-boot@0 {
-				reg = < 0 0x60000 >;
-				label = "u-boot";
-			};
-			u-boot-env@60000 {
-				reg = < 0x60000 0x20000 >;
-				label = "u-boot-env";
-			};
-			obmc-ubi@80000 {
-				reg = < 0x80000 0x7F80000>;
-				label = "obmc-ubi";
-			};
-		};
-	};
-
-	flash@1 {
-		status = "okay";
-		label = "alt-bmc";
-		m25p,fast-read;
-		spi-max-frequency = <100000000>;
-		partitions {
-			#address-cells = < 1 >;
-			#size-cells = < 1 >;
-			compatible = "fixed-partitions";
-			u-boot@0 {
-				reg = < 0 0x60000 >;
-				label = "alt-u-boot";
-			};
-			u-boot-env@60000 {
-				reg = < 0x60000 0x20000 >;
-				label = "alt-u-boot-env";
-			};
-			obmc-ubi@80000 {
-				reg = < 0x80000 0x7F80000>;
-				label = "alt-obmc-ubi";
-			};
-		};
-	};
-};
-
-&spi1 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_spi1_default>;
-
-	flash@0 {
-		status = "okay";
-		label = "pnor";
-		m25p,fast-read;
-		spi-max-frequency = <100000000>;
-	};
-};
-
-&uart1 {
-	/* Rear RS-232 connector */
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_txd1_default
-			&pinctrl_rxd1_default
-			&pinctrl_nrts1_default
-			&pinctrl_ndtr1_default
-			&pinctrl_ndsr1_default
-			&pinctrl_ncts1_default
-			&pinctrl_ndcd1_default
-			&pinctrl_nri1_default>;
-};
-
-&uart2 {
-	/* APSS */
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_txd2_default &pinctrl_rxd2_default>;
-};
-
-&uart5 {
-	status = "okay";
-};
-
-&lpc_ctrl {
-	status = "okay";
-	memory-region = <&flash_memory>;
-	flash = <&spi1>;
-};
-
-&mac0 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_rmii1_default>;
-	use-ncsi;
-	clocks = <&syscon ASPEED_CLK_GATE_MAC1CLK>,
-		 <&syscon ASPEED_CLK_MAC1RCLK>;
-	clock-names = "MACCLK", "RCLK";
-};
-
-&i2c2 {
-	status = "okay";
-
-	/* MUX ->
-	 *    Samtec 1
-	 *    Samtec 2
-	 */
-};
-
-&i2c3 {
-	status = "okay";
-
-	max31785@52 {
-		compatible = "maxim,max31785a";
-		reg = <0x52>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		fan@0 {
-			compatible = "pmbus-fan";
-			reg = <0>;
-			tach-pulses = <2>;
-			maxim,fan-rotor-input = "tach";
-			maxim,fan-pwm-freq = <25000>;
-			maxim,fan-no-watchdog;
-			maxim,fan-no-fault-ramp;
-			maxim,fan-ramp = <2>;
-			maxim,fan-fault-pin-mon;
-		};
-
-		fan@1 {
-			compatible = "pmbus-fan";
-			reg = <1>;
-			tach-pulses = <2>;
-			maxim,fan-rotor-input = "tach";
-			maxim,fan-pwm-freq = <25000>;
-			maxim,fan-no-watchdog;
-			maxim,fan-no-fault-ramp;
-			maxim,fan-ramp = <2>;
-			maxim,fan-fault-pin-mon;
-		};
-
-		fan@2 {
-			compatible = "pmbus-fan";
-			reg = <2>;
-			tach-pulses = <2>;
-			maxim,fan-rotor-input = "tach";
-			maxim,fan-pwm-freq = <25000>;
-			maxim,fan-no-watchdog;
-			maxim,fan-no-fault-ramp;
-			maxim,fan-ramp = <2>;
-			maxim,fan-fault-pin-mon;
-		};
-
-		fan@3 {
-			compatible = "pmbus-fan";
-			reg = <3>;
-			tach-pulses = <2>;
-			maxim,fan-rotor-input = "tach";
-			maxim,fan-pwm-freq = <25000>;
-			maxim,fan-no-watchdog;
-			maxim,fan-no-fault-ramp;
-			maxim,fan-ramp = <2>;
-			maxim,fan-fault-pin-mon;
-		};
-
-		fan@4 {
-			compatible = "pmbus-fan";
-			reg = <4>;
-			tach-pulses = <2>;
-			maxim,fan-rotor-input = "tach";
-			maxim,fan-pwm-freq = <25000>;
-			maxim,fan-no-watchdog;
-			maxim,fan-no-fault-ramp;
-			maxim,fan-ramp = <2>;
-			maxim,fan-fault-pin-mon;
-		};
-	};
-
-	pca0: pca9552@60 {
-		compatible = "nxp,pca9552";
-		reg = <0x60>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		gpio@0 {
-			reg = <0>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@1 {
-			reg = <1>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@2 {
-			reg = <2>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@3 {
-			reg = <3>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@4 {
-			reg = <4>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@5 {
-			reg = <5>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@6 {
-			reg = <6>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@7 {
-			reg = <7>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@8 {
-			reg = <8>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@9 {
-			reg = <9>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@10 {
-			reg = <10>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@11 {
-			reg = <11>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@12 {
-			reg = <12>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@13 {
-			reg = <13>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@14 {
-			reg = <14>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@15 {
-			reg = <15>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-	};
-
-	power-supply@68 {
-		compatible = "ibm,cffps2";
-		reg = <0x68>;
-	};
-
-	eeprom@50 {
-		compatible = "atmel,24c64";
-		reg = <0x50>;
-	};
-
-	power-supply@69 {
-		compatible = "ibm,cffps2";
-		reg = <0x69>;
-	};
-
-	eeprom@51 {
-		compatible = "atmel,24c64";
-		reg = <0x51>;
-	};
-};
-
-&i2c7 {
-	status = "okay";
-
-	dps: dps310@76 {
-		compatible = "infineon,dps310";
-		reg = <0x76>;
-		#io-channel-cells = <0>;
-	};
-
-	tmp275@48 {
-		compatible = "ti,tmp275";
-		reg = <0x48>;
-	};
-
-	si7021a20@20 {
-		compatible = "si,si7021a20";
-		reg = <0x20>;
-	};
-
-	eeprom@50 {
-		compatible = "atmel,24c64";
-		reg = <0x50>;
-	};
-
-	pca1: pca9551@60 {
-		compatible = "nxp,pca9551";
-		reg = <0x60>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		gpio@0 {
-			reg = <0>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@1 {
-			reg = <1>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@2 {
-			reg = <2>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@3 {
-			reg = <3>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@4 {
-			reg = <4>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@5 {
-			reg = <5>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@6 {
-			reg = <6>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@7 {
-			reg = <7>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-	};
-};
-
-&i2c8 {
-	status = "okay";
-
-	pca9552: pca9552@60 {
-		compatible = "nxp,pca9552";
-		reg = <0x60>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		gpio-line-names = "PS_SMBUS_RESET_N", "APSS_RESET_N",
-			"GPU0_TH_OVERT_N_BUFF",	"GPU1_TH_OVERT_N_BUFF",
-			"GPU2_TH_OVERT_N_BUFF", "GPU3_TH_OVERT_N_BUFF",
-			"P9_SCM0_PRES",	"P9_SCM1_PRES",
-			"GPU0_PWR_GOOD_BUFF", "GPU1_PWR_GOOD_BUFF",
-			"GPU2_PWR_GOOD_BUFF", "GPU3_PWR_GOOD_BUFF",
-			"PRESENT_VRM_CP0_N", "PRESENT_VRM_CP1_N",
-			"12V_BREAKER_FLT_N", "THROTTLE_UNLATCHED_N";
-
-		gpio@0 {
-			reg = <0>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@1 {
-			reg = <1>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@2 {
-			reg = <2>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@3 {
-			reg = <3>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@4 {
-			reg = <4>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@5 {
-			reg = <5>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@6 {
-			reg = <6>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@7 {
-			reg = <7>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@8 {
-			reg = <8>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@9 {
-			reg = <9>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@10 {
-			reg = <10>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@11 {
-			reg = <11>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@12 {
-			reg = <12>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@13 {
-			reg = <13>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@14 {
-			reg = <14>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-
-		gpio@15 {
-			reg = <15>;
-			type = <PCA955X_TYPE_GPIO>;
-		};
-	};
-
-	rtc@32 {
-		compatible = "epson,rx8900";
-		reg = <0x32>;
-	};
-
-	eeprom@51 {
-		compatible = "atmel,24c64";
-		reg = <0x51>;
-	};
-
-	ucd90160@64 {
-		compatible = "ti,ucd90160";
-		reg = <0x64>;
-	};
-};
-
-&i2c9 {
-	status = "okay";
-
-	eeprom@50 {
-		compatible = "atmel,24c64";
-		reg = <0x50>;
-	};
-
-	tmp423a@4c {
-		compatible = "ti,tmp423";
-		reg = <0x4c>;
-	};
-
-	ir35221@71 {
-		compatible = "infineon,ir35221";
-		reg = <0x71>;
-	};
-
-	ir35221@72 {
-		compatible = "infineon,ir35221";
-		reg = <0x72>;
-	};
-
-	pca2: pca9539@74 {
-		compatible = "nxp,pca9539";
-		reg = <0x74>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		gpio@0 {
-			reg = <0>;
-		};
-
-		gpio@1 {
-			reg = <1>;
-		};
-
-		gpio@2 {
-			reg = <2>;
-		};
-
-		gpio@3 {
-			reg = <3>;
-		};
-
-		gpio@4 {
-			reg = <4>;
-		};
-
-		gpio@5 {
-			reg = <5>;
-		};
-
-		gpio@6 {
-			reg = <6>;
-		};
-
-		gpio@7 {
-			reg = <7>;
-		};
-
-		gpio@8 {
-			reg = <8>;
-		};
-
-		gpio@9 {
-			reg = <9>;
-		};
-
-		gpio@10 {
-			reg = <10>;
-		};
-
-		gpio@11 {
-			reg = <11>;
-		};
-
-		gpio@12 {
-			reg = <12>;
-		};
-
-		gpio@13 {
-			reg = <13>;
-		};
-
-		gpio@14 {
-			reg = <14>;
-		};
-
-		gpio@15 {
-			reg = <15>;
-		};
-	};
-};
-
-&i2c10 {
-	status = "okay";
-
-	eeprom@50 {
-		compatible = "atmel,24c64";
-		reg = <0x50>;
-	};
-
-	tmp423a@4c {
-		compatible = "ti,tmp423";
-		reg = <0x4c>;
-	};
-
-	ir35221@71 {
-		compatible = "infineon,ir35221";
-		reg = <0x71>;
-	};
-
-	ir35221@72 {
-		compatible = "infineon,ir35221";
-		reg = <0x72>;
-	};
-
-	pca3: pca9539@74 {
-		compatible = "nxp,pca9539";
-		reg = <0x74>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		gpio@0 {
-			reg = <0>;
-		};
-
-		gpio@1 {
-			reg = <1>;
-		};
-
-		gpio@2 {
-			reg = <2>;
-		};
-
-		gpio@3 {
-			reg = <3>;
-		};
-
-		gpio@4 {
-			reg = <4>;
-		};
-
-		gpio@5 {
-			reg = <5>;
-		};
-
-		gpio@6 {
-			reg = <6>;
-		};
-
-		gpio@7 {
-			reg = <7>;
-		};
-
-		gpio@8 {
-			reg = <8>;
-		};
-
-		gpio@9 {
-			reg = <9>;
-		};
-
-		gpio@10 {
-			reg = <10>;
-		};
-
-		gpio@11 {
-			reg = <11>;
-		};
-
-		gpio@12 {
-			reg = <12>;
-		};
-
-		gpio@13 {
-			reg = <13>;
-		};
-
-		gpio@14 {
-			reg = <14>;
-		};
-
-		gpio@15 {
-			reg = <15>;
-		};
-	};
-};
-
-&i2c11 {
-	/* MUX
-	 *   -> PCIe Slot 0
-	 *   -> PCIe Slot 1
-	 *   -> PCIe Slot 2
-	 *   -> PCIe Slot 3
-	 */
-	status = "okay";
-};
-
-&i2c12 {
-	status = "okay";
-
-	tmp275@48 {
-		compatible = "ti,tmp275";
-		reg = <0x48>;
-	};
-
-	tmp275@4a {
-		compatible = "ti,tmp275";
-		reg = <0x4a>;
-	};
-};
-
-&i2c13 {
-	status = "okay";
-};
-
-&vuart {
-	status = "okay";
-};
-
-&gfx {
-	status = "okay";
-	memory-region = <&gfx_memory>;
-};
-
-&pinctrl {
-	aspeed,external-nodes = <&gfx &lhc>;
-};
-
-&wdt1 {
-	aspeed,reset-type = "none";
-	aspeed,external-signal;
-	aspeed,ext-push-pull;
-	aspeed,ext-active-high;
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_wdtrst1_default>;
-};
-
-&wdt2 {
-	aspeed,alt-boot;
-};
-
-&ibt {
-	status = "okay";
-};
-
-&adc {
-	status = "okay";
-};
-
-&sdmmc {
-       status = "okay";
-};
-
-&sdhci1 {
-       status = "okay";
-
-       pinctrl-names = "default";
-       pinctrl-0 = <&pinctrl_sd2_default>;
-};
-
-#include "ibm-power9-dual.dtsi"
diff --git a/arch/arm/boot/dts/aspeed/Makefile b/arch/arm/boot/dts/aspeed/Makefile
new file mode 100644
index 000000000000..0f0b5b707654
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/Makefile
@@ -0,0 +1,80 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_ASPEED) += \
+	aspeed-ast2500-evb.dtb \
+	aspeed-ast2600-evb-a1.dtb \
+	aspeed-ast2600-evb.dtb \
+	aspeed-bmc-amd-daytonax.dtb \
+	aspeed-bmc-amd-ethanolx.dtb \
+	aspeed-bmc-ampere-mtjade.dtb \
+	aspeed-bmc-ampere-mtjefferson.dtb \
+	aspeed-bmc-ampere-mtmitchell.dtb \
+	aspeed-bmc-arm-stardragon4800-rep2.dtb \
+	aspeed-bmc-asrock-e3c246d4i.dtb \
+	aspeed-bmc-asrock-e3c256d4i.dtb \
+	aspeed-bmc-asrock-romed8hm3.dtb \
+	aspeed-bmc-asrock-spc621d8hm3.dtb \
+	aspeed-bmc-asrock-x570d4u.dtb \
+	aspeed-bmc-asus-x4tf.dtb \
+	aspeed-bmc-bytedance-g220a.dtb \
+	aspeed-bmc-delta-ahe50dc.dtb \
+	aspeed-bmc-facebook-bletchley.dtb \
+	aspeed-bmc-facebook-catalina.dtb \
+	aspeed-bmc-facebook-clemente.dtb \
+	aspeed-bmc-facebook-cmm.dtb \
+	aspeed-bmc-facebook-darwin.dtb \
+	aspeed-bmc-facebook-elbert.dtb \
+	aspeed-bmc-facebook-fuji-data64.dtb \
+	aspeed-bmc-facebook-fuji.dtb \
+	aspeed-bmc-facebook-galaxy100.dtb \
+	aspeed-bmc-facebook-greatlakes.dtb \
+	aspeed-bmc-facebook-harma.dtb \
+	aspeed-bmc-facebook-minerva.dtb \
+	aspeed-bmc-facebook-minipack.dtb \
+	aspeed-bmc-facebook-santabarbara.dtb \
+	aspeed-bmc-facebook-tiogapass.dtb \
+	aspeed-bmc-facebook-wedge40.dtb \
+	aspeed-bmc-facebook-wedge100.dtb \
+	aspeed-bmc-facebook-wedge400-data64.dtb \
+	aspeed-bmc-facebook-wedge400.dtb \
+	aspeed-bmc-facebook-yamp.dtb \
+	aspeed-bmc-facebook-yosemitev2.dtb \
+	aspeed-bmc-facebook-yosemite4.dtb \
+	aspeed-bmc-ibm-blueridge.dtb \
+	aspeed-bmc-ibm-bonnell.dtb \
+	aspeed-bmc-ibm-everest.dtb \
+	aspeed-bmc-ibm-fuji.dtb \
+	aspeed-bmc-ibm-rainier.dtb \
+	aspeed-bmc-ibm-rainier-1s4u.dtb \
+	aspeed-bmc-ibm-rainier-4u.dtb \
+	aspeed-bmc-ibm-sbp1.dtb \
+	aspeed-bmc-ibm-system1.dtb \
+	aspeed-bmc-intel-s2600wf.dtb \
+	aspeed-bmc-inspur-fp5280g2.dtb \
+	aspeed-bmc-inspur-nf5280m6.dtb \
+	aspeed-bmc-inspur-on5263m5.dtb \
+	aspeed-bmc-lenovo-hr630.dtb \
+	aspeed-bmc-lenovo-hr855xg2.dtb \
+	aspeed-bmc-microsoft-olympus.dtb \
+	aspeed-bmc-nvidia-gb200nvl-bmc.dtb \
+	aspeed-bmc-opp-lanyang.dtb \
+	aspeed-bmc-opp-mowgli.dtb \
+	aspeed-bmc-opp-nicole.dtb \
+	aspeed-bmc-opp-palmetto.dtb \
+	aspeed-bmc-opp-romulus.dtb \
+	aspeed-bmc-opp-tacoma.dtb \
+	aspeed-bmc-opp-vesnin.dtb \
+	aspeed-bmc-opp-witherspoon.dtb \
+	aspeed-bmc-opp-zaius.dtb \
+	aspeed-bmc-portwell-neptune.dtb \
+	aspeed-bmc-qcom-dc-scm-v1.dtb \
+	aspeed-bmc-quanta-q71l.dtb \
+	aspeed-bmc-quanta-s6q.dtb \
+	aspeed-bmc-supermicro-x11spi.dtb \
+	aspeed-bmc-inventec-starscream.dtb \
+	aspeed-bmc-inventec-transformers.dtb \
+	aspeed-bmc-tyan-s7106.dtb \
+	aspeed-bmc-tyan-s8036.dtb \
+	aspeed-bmc-ufispace-ncplite.dtb \
+	aspeed-bmc-vegman-n110.dtb \
+	aspeed-bmc-vegman-rx20.dtb \
+	aspeed-bmc-vegman-sx20.dtb
diff --git a/arch/arm/boot/dts/aspeed-ast2500-evb.dts b/arch/arm/boot/dts/aspeed/aspeed-ast2500-evb.dts
index 1d24b394ea4c..a497dd135491 100644
--- a/arch/arm/boot/dts/aspeed-ast2500-evb.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-ast2500-evb.dts
@@ -5,7 +5,7 @@
 
 / {
 	model = "AST2500 EVB";
-	compatible = "aspeed,ast2500";
+	compatible = "aspeed,ast2500-evb", "aspeed,ast2500";
 
 	aliases {
 		serial4 = &uart5;
diff --git a/arch/arm/boot/dts/aspeed-ast2600-evb-a1.dts b/arch/arm/boot/dts/aspeed/aspeed-ast2600-evb-a1.dts
index dd7148060c4a..f34a2b1ec2f0 100644
--- a/arch/arm/boot/dts/aspeed-ast2600-evb-a1.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-ast2600-evb-a1.dts
@@ -5,6 +5,7 @@
 
 / {
 	model = "AST2600 A1 EVB";
+	compatible = "aspeed,ast2600-evb-a1", "aspeed,ast2600-evb", "aspeed,ast2600";
 
 	/delete-node/regulator-vcc-sdhci0;
 	/delete-node/regulator-vcc-sdhci1;
diff --git a/arch/arm/boot/dts/aspeed-ast2600-evb.dts b/arch/arm/boot/dts/aspeed/aspeed-ast2600-evb.dts
index b7eb552640cb..de83c0eb1d6e 100644
--- a/arch/arm/boot/dts/aspeed-ast2600-evb.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-ast2600-evb.dts
@@ -8,7 +8,7 @@
 
 / {
 	model = "AST2600 EVB";
-	compatible = "aspeed,ast2600";
+	compatible = "aspeed,ast2600-evb", "aspeed,ast2600";
 
 	aliases {
 		serial4 = &uart5;
@@ -23,6 +23,26 @@
 		reg = <0x80000000 0x80000000>;
 	};
 
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		video_engine_memory: video {
+			size = <0x04000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+
+		gfx_memory: framebuffer {
+			size = <0x01000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+	};
+
 	vcc_sdhci0: regulator-vcc-sdhci0 {
 		compatible = "regulator-fixed";
 		regulator-name = "SDHCI0 Vcc";
@@ -103,7 +123,7 @@
 &mac0 {
 	status = "okay";
 
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-rxid";
 	phy-handle = <&ethphy0>;
 
 	pinctrl-names = "default";
@@ -114,7 +134,7 @@
 &mac1 {
 	status = "okay";
 
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-rxid";
 	phy-handle = <&ethphy1>;
 
 	pinctrl-names = "default";
@@ -162,6 +182,7 @@
 		status = "okay";
 		m25p,fast-read;
 		label = "bmc";
+		spi-rx-bus-width = <4>;
 		spi-max-frequency = <50000000>;
 #include "openbmc-flash-layout-64.dtsi"
 	};
@@ -176,6 +197,7 @@
 		status = "okay";
 		m25p,fast-read;
 		label = "pnor";
+		spi-rx-bus-width = <4>;
 		spi-max-frequency = <100000000>;
 	};
 };
@@ -187,11 +209,6 @@
 
 &i2c0 {
 	status = "okay";
-
-	temp@2e {
-		compatible = "adi,adt7490";
-		reg = <0x2e>;
-	};
 };
 
 &i2c1 {
@@ -220,10 +237,26 @@
 
 &i2c7 {
 	status = "okay";
+
+	temp@2e {
+		compatible = "adi,adt7490";
+		reg = <0x2e>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c08";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
 };
 
 &i2c8 {
 	status = "okay";
+
+	lm75@4d {
+		compatible = "national,lm75";
+		reg = <0x4d>;
+	};
 };
 
 &i2c9 {
@@ -300,3 +333,18 @@
 	vqmmc-supply = <&vccq_sdhci1>;
 	clk-phase-sd-hs = <7>, <200>;
 };
+
+&vhub {
+	status = "okay";
+	pinctrl-names = "default";
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+&gfx {
+	status = "okay";
+	memory-region = <&gfx_memory>;
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-amd-daytonax.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-amd-daytonax.dts
new file mode 100644
index 000000000000..64bb9bf92de2
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-amd-daytonax.dts
@@ -0,0 +1,319 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "AMD DaytonaX BMC";
+	compatible = "amd,daytonax-bmc", "aspeed,ast2500";
+
+	memory@80000000 {
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		video_engine_memory: jpegbuffer {
+			size = <0x02000000>;	/* 32M */
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+	};
+
+	aliases {
+		serial0 = &uart1;
+		serial4 = &uart5;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-fault {
+			gpios = <&gpio ASPEED_GPIO(A, 2) GPIO_ACTIVE_LOW>;
+		};
+
+		led-identify {
+			gpios = <&gpio ASPEED_GPIO(A, 3) GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>, <&adc 4>,
+			<&adc 5>, <&adc 6>, <&adc 7>, <&adc 8>, <&adc 9>,
+			<&adc 10>, <&adc 11>, <&adc 12>, <&adc 13>, <&adc 14>,
+			<&adc 15>;
+	};
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		#include "openbmc-flash-layout.dtsi"
+	};
+};
+
+&mac0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii1_default &pinctrl_mdio1_default>;
+};
+
+&uart1 {
+	//Host Console
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd1_default
+		&pinctrl_rxd1_default
+		&pinctrl_nrts1_default
+		&pinctrl_ndtr1_default
+		&pinctrl_ndsr1_default
+		&pinctrl_ncts1_default
+		&pinctrl_ndcd1_default
+		&pinctrl_nri1_default>;
+};
+
+&uart5 {
+	//BMC Console
+	status = "okay";
+};
+
+&vuart {
+	status = "okay";
+	aspeed,lpc-io-reg = <0x3f8>;
+	aspeed,lpc-interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&adc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default
+		&pinctrl_adc1_default
+		&pinctrl_adc2_default
+		&pinctrl_adc3_default
+		&pinctrl_adc4_default
+		&pinctrl_adc5_default
+		&pinctrl_adc6_default
+		&pinctrl_adc7_default
+		&pinctrl_adc8_default
+		&pinctrl_adc9_default
+		&pinctrl_adc10_default
+		&pinctrl_adc11_default
+		&pinctrl_adc12_default
+		&pinctrl_adc13_default
+		&pinctrl_adc14_default
+		&pinctrl_adc15_default>;
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names =
+	/*A0-A7*/	"","","led-fault","led-identify","","","","",
+	/*B0-B7*/	"","","","","","","","",
+	/*C0-C7*/	"id-button","","","","","","","",
+	/*D0-D7*/	"","","ASSERT_BMC_READY","","","","","",
+	/*E0-E7*/	"reset-button","reset-control","power-button","power-control","",
+			"power-good","power-ok","",
+	/*F0-F7*/	"","","","","","","BATTERY_DETECT","",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"","","","","","","","",
+	/*I0-I7*/	"","","","","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"","","","","","","","",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","","","","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"","","","","","","","",
+	/*AA0-AA7*/	"","","","","","","","",
+	/*AB0-AB7*/	"FM_BMC_READ_SPD_TEMP","","","","","","","",
+	/*AC0-AC7*/	"","","","","","","","";
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+};
+
+&i2c12 {
+	status = "okay";
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+};
+
+&lpc_snoop {
+	status = "okay";
+	snoop-ports = <0x80>, <0x81>;
+};
+
+&lpc_ctrl {
+	status = "okay";
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_default
+		&pinctrl_pwm1_default
+		&pinctrl_pwm2_default
+		&pinctrl_pwm3_default
+		&pinctrl_pwm4_default
+		&pinctrl_pwm5_default
+		&pinctrl_pwm6_default
+		&pinctrl_pwm7_default>;
+
+	fan@0 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x00>;
+	};
+
+	fan@1 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x01>;
+	};
+
+	fan@2 {
+		reg = <0x01>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x02>;
+	};
+
+	fan@3 {
+		reg = <0x01>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x03>;
+	};
+
+	fan@4 {
+		reg = <0x02>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x04>;
+	};
+
+	fan@5 {
+		reg = <0x02>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x05>;
+	};
+
+	fan@6 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x06>;
+	};
+
+	fan@7 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x07>;
+	};
+
+	fan@8 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x08>;
+	};
+
+	fan@9 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x09>;
+	};
+
+	fan@10 {
+		reg = <0x05>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0a>;
+	};
+
+	fan@11 {
+		reg = <0x05>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0b>;
+	};
+
+	fan@12 {
+		reg = <0x06>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0c>;
+	};
+
+	fan@13 {
+		reg = <0x06>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0d>;
+	};
+
+	fan@14 {
+		reg = <0x07>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0e>;
+	};
+
+	fan@15 {
+		reg = <0x07>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0f>;
+	};
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+&vhub {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-amd-ethanolx.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-amd-ethanolx.dts
index 6406a0f080ee..6bded774c457 100644
--- a/arch/arm/boot/dts/aspeed-bmc-amd-ethanolx.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-amd-ethanolx.dts
@@ -5,6 +5,7 @@
 
 #include "aspeed-g5.dtsi"
 #include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	model = "AMD EthanolX BMC";
@@ -58,10 +59,22 @@
 	flash@0 {
 		status = "okay";
 		m25p,fast-read;
+		label = "bmc";
 		#include "openbmc-flash-layout.dtsi"
 	};
 };
 
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bios";
+		spi-max-frequency = <100000000>;
+	};
+};
 
 &mac0 {
 	status = "okay";
@@ -78,7 +91,9 @@
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_txd1_default
-		     &pinctrl_rxd1_default>;
+		     &pinctrl_rxd1_default
+		     &pinctrl_nrts1_default
+		     &pinctrl_ncts1_default>;
 };
 
 &uart5 {
@@ -160,7 +175,7 @@
 &i2c3 {
 	status = "okay";
 	eeprom@50 {
-		compatible = "atmel,24c256";
+		compatible = "atmel,24c128";
 		reg = <0x50>;
 		pagesize = <64>;
 	};
@@ -261,6 +276,12 @@
 	status = "okay";
 };
 
+&vuart {
+	status = "okay";
+	aspeed,lpc-io-reg = <0x3f8>;
+	aspeed,lpc-interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+};
+
 &pwm_tacho {
 	status = "okay";
 	pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/aspeed-bmc-ampere-mtjade.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtjade.dts
index 1b2e7ad37566..263702599767 100644
--- a/arch/arm/boot/dts/aspeed-bmc-ampere-mtjade.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtjade.dts
@@ -49,6 +49,11 @@
 		 */
 		i2c80 = &nvme_m2_0;
 		i2c81 = &nvme_m2_1;
+
+		/*
+		 *  i2c bus 82 assigned to OCP slot
+		 */
+		i2c82 = &ocpslot;
 	};
 
 	chosen {
@@ -97,101 +102,6 @@
 		};
 	};
 
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		shutdown_ack {
-			label = "SHUTDOWN_ACK";
-			gpios = <&gpio ASPEED_GPIO(G, 2) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(G, 2)>;
-		};
-
-		reboot_ack {
-			label = "REBOOT_ACK";
-			gpios = <&gpio ASPEED_GPIO(J, 3) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(J, 3)>;
-		};
-
-		S0_overtemp {
-			label = "S0_OVERTEMP";
-			gpios = <&gpio ASPEED_GPIO(G, 3) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(G, 3)>;
-		};
-
-		S0_hightemp {
-			label = "S0_HIGHTEMP";
-			gpios = <&gpio ASPEED_GPIO(J, 0) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(J, 0)>;
-		};
-
-		S0_cpu_fault {
-			label = "S0_CPU_FAULT";
-			gpios = <&gpio ASPEED_GPIO(J, 1) GPIO_ACTIVE_HIGH>;
-			linux,code = <ASPEED_GPIO(J, 1)>;
-		};
-
-		S0_scp_auth_fail {
-			label = "S0_SCP_AUTH_FAIL";
-			gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(J, 2)>;
-		};
-
-		S1_scp_auth_fail {
-			label = "S1_SCP_AUTH_FAIL";
-			gpios = <&gpio ASPEED_GPIO(Z, 5) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(Z, 5)>;
-		};
-
-		S1_overtemp {
-			label = "S1_OVERTEMP";
-			gpios = <&gpio ASPEED_GPIO(Z, 6) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(Z, 6)>;
-		};
-
-		S1_hightemp {
-			label = "S1_HIGHTEMP";
-			gpios = <&gpio ASPEED_GPIO(AB, 0) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(AB, 0)>;
-		};
-
-		S1_cpu_fault {
-			label = "S1_CPU_FAULT";
-			gpios = <&gpio ASPEED_GPIO(Z, 1) GPIO_ACTIVE_HIGH>;
-			linux,code = <ASPEED_GPIO(Z, 1)>;
-		};
-
-		id_button {
-			label = "ID_BUTTON";
-			gpios = <&gpio ASPEED_GPIO(Q, 5) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(Q, 5)>;
-		};
-
-		psu1_vin_good {
-			label = "PSU1_VIN_GOOD";
-			gpios = <&gpio ASPEED_GPIO(H, 4) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(H, 4)>;
-		};
-
-		psu2_vin_good {
-			label = "PSU2_VIN_GOOD";
-			gpios = <&gpio ASPEED_GPIO(H, 5) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(H, 5)>;
-		};
-
-		psu1_present {
-			label = "PSU1_PRESENT";
-			gpios = <&gpio ASPEED_GPIO(I, 0) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(I, 0)>;
-		};
-
-		psu2_present {
-			label = "PSU2_PRESENT";
-			gpios = <&gpio ASPEED_GPIO(I, 1) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(I, 1)>;
-		};
-
-	};
-
 	gpioA0mux: mux-controller {
 		compatible = "gpio-mux";
 		#mux-control-cells = <0>;
@@ -437,6 +347,10 @@
 
 &i2c0 {
 	status = "okay";
+	ssif-bmc@10 {
+		compatible = "ssif-bmc";
+		reg = <0x10>;
+	};
 };
 
 &i2c1 {
@@ -445,6 +359,14 @@
 
 &i2c2 {
 	status = "okay";
+	smpro@4f {
+		compatible = "ampere,smpro";
+		reg = <0x4f>;
+	};
+	smpro@4e {
+		compatible = "ampere,smpro";
+		reg = <0x4e>;
+	};
 };
 
 &i2c3 {
@@ -503,6 +425,17 @@
 		reg = <0x70>;
 		i2c-mux-idle-disconnect;
 
+		ocpslot: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+
+			ocpslot_temp: temperature-sensor@1f {
+				compatible = "ti,tmp421";
+				reg = <0x1f>;
+			};
+		};
+
 		nvmeslot_0_7: i2c@3 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -755,10 +688,6 @@
 	memory-region = <&gfx_memory>;
 };
 
-&pinctrl {
-	aspeed,external-nodes = <&gfx &lhc>;
-};
-
 &pwm_tacho {
 	status = "okay";
 	pinctrl-names = "default";
@@ -843,49 +772,63 @@
 
 &gpio {
 	gpio-line-names =
-	/*A0-A7*/	"","","","S0_BMC_SPECIAL_BOOT","","","","",
-	/*B0-B7*/	"BMC_SELECT_EEPROM","","","",
-			"POWER_BUTTON","","","",
+	/*A0-A7*/	"","","","host0-special-boot","","","","",
+	/*B0-B7*/	"i2c-backup-sel","","","",
+			"power-button","presence-cpu0","","",
 	/*C0-C7*/	"","","","","","","","",
 	/*D0-D7*/	"","","","","","","","",
 	/*E0-E7*/	"","","","","","","","",
-	/*F0-F7*/	"","","BMC_SYS_PSON_L","S0_DDR_SAVE","PGOOD",
-			"S1_DDR_SAVE","","",
-	/*G0-G7*/	"host0-ready","SHD_REQ_L","","S0_OVERTEMP_L","","",
-			"","",
-	/*H0-H7*/	"","","","","PSU1_VIN_GOOD","PSU2_VIN_GOOD","","",
-	/*I0-I7*/	"PSU1_PRESENT","PSU2_PRESENT","S1_BMC_SPECIAL_BOOT",
-			"","","","","",
-	/*J0-J7*/	"S0_HIGHTEMP_L","S0_FAULT_L","S0_SCP_AUTH_FAIL_L","",
-			"","","","",
+	/*F0-F7*/	"ps0-pgood","ps1-pgood","power-chassis-control","s0-ddr-save",
+			"power-chassis-good", "s1-ddr-save","","",
+	/*G0-G7*/	"host0-ready","host0-shd-req-n","host0-shd-ack-n",
+			"s0-overtemp-n","","","","",
+	/*H0-H7*/	"uart1-mode1","uart2-mode1","uart3-mode1","uart4-mode1",
+			"ps0-vin-good","ps1-vin-good","","i2c6-reset-n",
+	/*I0-I7*/	"presence-ps0","presence-ps1","s1-special-boot","","","","","",
+	/*J0-J7*/	"s0-hightemp-n","s0-fault-alert","s0-sys-auth-failure-n",
+			"host0-reboot-ack-n","","","","",
 	/*K0-K7*/	"","","","","","","","",
-	/*L0-L7*/       "","","","BMC_SYSRESET_L","SPI_AUTH_FAIL_L","","","",
-	/*M0-M7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","host0-sysreset-n","s0-spi-auth-fail-n","","","",
+	/*M0-M7*/	"","","","","s0-i2c9-alert-n","s1-i2c9-alert-n","","",
 	/*N0-N7*/	"","","","","","","","",
 	/*O0-O7*/	"","","","","","","","",
 	/*P0-P7*/	"","","","","","","","",
-	/*Q0-Q7*/	"","","","","","UID_BUTTON","","",
-	/*R0-R7*/	"","","BMC_EXT_HIGHTEMP_L","OCP_AUX_PWREN",
-			"OCP_MAIN_PWREN","RESET_BUTTON","","",
-	/*S0-S7*/	"","","","","rtc-battery-voltage-read-enable","","","",
+	/*Q0-Q7*/	"","","","","","identify-button","led-identify","",
+	/*R0-R7*/	"","","ext-hightemp-n","","ocp-main-pwren","reset-button","","",
+	/*S0-S7*/	"s0-vr-hot-n","s1-vr-hot-n","","",
+			"rtc-battery-voltage-read-enable","vr-pmbus-sel-n","","",
 	/*T0-T7*/	"","","","","","","","",
 	/*U0-U7*/	"","","","","","","","",
 	/*V0-V7*/	"","","","","","","","",
 	/*W0-W7*/	"","","","","","","","",
 	/*X0-X7*/	"","","","","","","","",
-	/*Y0-Y7*/	"","","","","","","","",
-	/*Z0-Z7*/	"S0_BMC_PLIMIT","S1_FAULT_L","S1_FW_BOOT_OK","","",
-			"S1_SCP_AUTH_FAIL_L","S1_OVERTEMP_L","",
+	/*Y0-Y7*/	"","","","bmc-vga-en-n","","","","",
+	/*Z0-Z7*/	"s0-plimit","s1-fault-alert","s1-fw-boot-ok","s0-rtc-lock","",
+			"s1-sys-auth-failure-n","s1-overtemp-n","",
 	/*AA0-AA7*/	"","","","","","","","",
-	/*AB0-AB7*/	"S1_HIGHTEMP_L","S1_BMC_PLIMIT","S0_BMC_DDR_ADDR",
-			"S1_BMC_DDR_ADR","","","","",
-	/*AC0-AC7*/	"SYS_PWR_GD","","","","","BMC_READY","SLAVE_PRESENT_L",
-			"BMC_OCP_PG";
+	/*AB0-AB7*/	"s1-hightemp-n","s1-plimit","s0-ddr-addr","s1-ddr-addr","","",
+			"","",
+	/*AC0-AC7*/	"sys-pwr-gd","","spi0-program-sel","spi0-backup-sel","bmc-ok",
+			"","presence-cpu1","ocp-pgood";
 
 	i2c4-o-en-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(Y, 2) GPIO_ACTIVE_HIGH>;
 		output-high;
-		line-name = "BMC_I2C4_O_EN";
+		line-name = "i2c4-o-en";
+	};
+
+	ocp-aux-pwren-hog {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(R, 3) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "ocp-aux-pwren";
+	};
+
+	bmc-ready-hog {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(AC, 5) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "bmc-ready";
 	};
 };
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtjefferson.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtjefferson.dts
new file mode 100644
index 000000000000..53b4372f1a08
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtjefferson.dts
@@ -0,0 +1,622 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright 2024 Ampere Computing LLC.
+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+	model = "Ampere Mt. Jefferson BMC";
+	compatible = "ampere,mtjefferson-bmc", "aspeed,ast2600";
+
+	aliases {
+		i2c20 = &i2c4_bus70_chn0;
+		i2c22 = &i2c4_bus70_chn2;
+
+		/*
+		 *  I2C OCP alias port
+		 */
+		i2c30 = &ocpslot;
+
+		/*
+		 *  I2C NVMe alias port
+		 */
+		i2c48 = &nvmeslot_0;
+		i2c49 = &nvmeslot_1;
+		i2c50 = &nvmeslot_2;
+		i2c51 = &nvmeslot_3;
+		i2c52 = &nvmeslot_4;
+		i2c53 = &nvmeslot_5;
+		i2c54 = &nvmeslot_6;
+		i2c55 = &nvmeslot_7;
+		i2c56 = &nvmeslot_8;
+		i2c57 = &nvmeslot_9;
+		i2c58 = &nvmeslot_10;
+		i2c59 = &nvmeslot_11;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		gfx_memory: framebuffer {
+			size = <0x01000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+
+		video_engine_memory: video {
+			size = <0x04000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+
+		vga_memory: region@bf000000 {
+			no-map;
+			compatible = "shared-dma-pool";
+			reg = <0xbf000000 0x01000000>;  /* 16M */
+		};
+	};
+
+	voltage_mon_reg: voltage-mon-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "ltc2497_reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-bmc-ready {
+			gpios = <&gpio0 ASPEED_GPIO(W, 5) (GPIO_ACTIVE_HIGH | GPIO_TRANSITORY)>;
+		};
+
+		led-sw-heartbeat {
+			gpios = <&gpio0 ASPEED_GPIO(N, 3) GPIO_ACTIVE_HIGH>;
+		};
+
+		led-identify {
+			gpios = <&gpio0 ASPEED_GPIO(S, 3) GPIO_ACTIVE_HIGH>;
+		};
+
+		led-fault {
+			gpios = <&gpio0 ASPEED_GPIO(P, 4) GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels =   <&adc0 0>, <&adc0 1>, <&adc0 2>,
+				<&adc_i2c_2 0>, <&adc_i2c_2 1>,
+				<&adc_i2c_2 2>, <&adc_i2c_2 3>,
+				<&adc_i2c_2 4>, <&adc_i2c_2 5>,
+				<&adc_i2c_2 6>, <&adc_i2c_2 7>,
+				<&adc_i2c_2 8>, <&adc_i2c_2 9>,
+				<&adc_i2c_2 10>, <&adc_i2c_2 11>,
+				<&adc_i2c_2 12>, <&adc_i2c_2 13>,
+				<&adc_i2c_2 14>, <&adc_i2c_2 15>,
+				<&adc_i2c_0 0>, <&adc_i2c_0 1>,
+				<&adc_i2c_0 2>, <&adc_i2c_0 3>,
+				<&adc_i2c_0 4>, <&adc_i2c_0 5>,
+				<&adc_i2c_0 6>, <&adc_i2c_0 7>,
+				<&adc_i2c_0 8>, <&adc_i2c_0 9>,
+				<&adc_i2c_0 10>, <&adc_i2c_0 11>,
+				<&adc_i2c_0 12>;
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mac0 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii1_default>;
+};
+
+&mac3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+	use-ncsi;
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64.dtsi"
+	};
+
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "alt-bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64-alt.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "pnor";
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+	bus-frequency = <1000000>;
+	multi-master;
+	mctp-controller;
+
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9545";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		i2c4_bus70_chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+
+			eeprom@52 {
+				compatible = "atmel,24c256";
+				reg = <0x52>;
+				pagesize = <32>;
+			};
+			temperature-sensor@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+			temperature-sensor@49 {
+				compatible = "ti,tmp75";
+				reg = <0x49>;
+			};
+			temperature-sensor@4a {
+				compatible = "ti,tmp75";
+				reg = <0x4a>;
+			};
+			temperature-sensor@4b {
+				compatible = "ti,tmp464";
+				reg = <0x4b>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				channel@0 {
+					reg = <0x0>;
+					status = "disabled";
+				};
+				channel@1 {
+					reg = <0x1>;
+					status = "disabled";
+				};
+				channel@2 {
+					reg = <0x2>;
+					status = "disabled";
+				};
+				channel@3 {
+					reg = <0x3>;
+					status = "disabled";
+				};
+				channel@4 {
+					reg = <0x4>;
+				};
+			};
+			temperature-sensor@4d {
+				compatible = "ti,tmp75";
+				reg = <0x4d>;
+			};
+			temperature-sensor@4e {
+				compatible = "ti,tmp75";
+				reg = <0x4e>;
+			};
+			temperature-sensor@4f {
+				compatible = "ti,tmp75";
+				reg = <0x4f>;
+			};
+			temperature-sensor@28 {
+				compatible = "nuvoton,nct7802";
+				reg = <0x28>;
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+				channel@1 { /* RTD1 */
+					reg = <1>;
+					sensor-type = "temperature";
+					temperature-mode = "thermistor";
+				};
+			};
+			adc_i2c_0: adc@14 {
+				compatible = "lltc,ltc2497";
+				reg = <0x14>;
+				vref-supply = <&voltage_mon_reg>;
+				#io-channel-cells = <1>;
+			};
+		};
+
+		i2c4_bus70_chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+
+			adc_i2c_2: adc@14 {
+				compatible = "lltc,ltc2497";
+				reg = <0x14>;
+				vref-supply = <&voltage_mon_reg>;
+				#io-channel-cells = <1>;
+			};
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+
+			i2c-mux@71 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x71>;
+				i2c-mux-idle-disconnect;
+
+				nvmeslot_8: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x0>;
+				};
+				nvmeslot_9: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x1>;
+				};
+				nvmeslot_10: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x2>;
+				};
+				nvmeslot_11: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x3>;
+				};
+			};
+
+			i2c-mux@72 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x72>;
+				i2c-mux-idle-disconnect;
+
+				nvmeslot_4: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x4>;
+				};
+				nvmeslot_5: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x5>;
+				};
+				nvmeslot_6: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x6>;
+				};
+				nvmeslot_7: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x7>;
+				};
+			};
+
+			i2c-mux@74 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x74>;
+				i2c-mux-idle-disconnect;
+
+				ocpslot: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x0>;
+
+					ocpslot_temp: temperature-sensor@1f {
+						compatible = "ti,tmp421";
+						reg = <0x1f>;
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						channel@0 {
+							reg = <0x0>;
+							status = "disabled";
+						};
+						channel@1 {
+							reg = <0x1>;
+						};
+					};
+				};
+
+				nvmeslot_0: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x4>;
+				};
+				nvmeslot_1: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x5>;
+				};
+				nvmeslot_2: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x6>;
+				};
+				nvmeslot_3: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x7>;
+				};
+			};
+		};
+	};
+};
+
+&i2c6 {
+	status = "okay";
+
+	rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&i2c7 {
+	status = "okay";
+
+	temperature-sensor@4f {
+		compatible = "ti,tmp75";
+		reg = <0x4f>;
+	};
+};
+
+&i2c8 {
+	status = "okay";
+
+	fan-controller@5c {
+		compatible = "onnn,adt7462";
+		reg = <0x5c>;
+	};
+};
+
+&i2c9 {
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+	};
+
+	eeprom@52 {
+		compatible = "atmel,24c02";
+		reg = <0x52>;
+	};
+
+	temperature-sensor@18 {
+		compatible = "jedec,jc-42.4-temp";
+		reg = <0x18>;
+	};
+
+	temperature-sensor@1a {
+		compatible = "jedec,jc-42.4-temp";
+		reg = <0x1a>;
+	};
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+	ssif-bmc@10 {
+		compatible = "ssif-bmc";
+		reg = <0x10>;
+	};
+};
+
+&i2c14 {
+	status = "okay";
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	bmc_ast2600_cpu: temperature-sensor@48 {
+		compatible = "ti,tmp75";
+		reg = <0x48>;
+	};
+};
+
+&i2c15 {
+	status = "okay";
+	gpio_expander1: gpio-expander@22 {
+		compatible = "nxp,pca9535";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+			"presence-ocp1","presence-ocp2",
+			"","",
+			"","",
+			"","",
+			"","",
+			"","",
+			"","",
+			"","";
+	};
+};
+
+&adc0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+		&pinctrl_adc2_default>;
+};
+
+&vhub {
+	status = "okay";
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+&gpio0 {
+	gpio-line-names =
+	/*A0-A7*/	"","","","","cpu-type-detect","i2c2-reset-n","i2c6-reset-n","i2c5-reset-n",
+	/*B0-B7*/	"","","","","host0-sysreset-n","host0-pmin-n","fru-rd-complete",
+			"chassis-id-sel",
+	/*C0-C7*/	"s0-vrd-fault-n","","bmc-debug-mode","","cpld-3v3-irq-n","","vrd-sel",
+			"spd-sel",
+	/*D0-D7*/	"presence-ps0","presence-ps1","hsc-12vmain-alt2-n","ext-high-temp-n",
+			"","","","",
+	/*E0-E7*/	"eth-phy-rst-n","eth-phy-int-n","","","","","","",
+	/*F0-F7*/	"s0-pcp-oc-warn-n","","power-chassis-control",
+			"cpu-bios-recover","s0-heartbeat","hs-scout-proc-hot","s0-vr-hot-n","",
+	/*G0-G7*/	"","","hsc-12vmain-alt1-n","","","bp-cpld-program-en","led-fp-sta-gr",
+			"led-fp-sta-amb",
+	/*H0-H7*/	"jtag-program-sel","jtag-cmpl2","wd-disable-n","power-chassis-good","","",
+			"","",
+	/*I0-I7*/	"","","","","","","power-button","rtc-battery-voltage-read-enable",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","reset-button","","","",
+	/*M0-M7*/	"nmi-n","s0-ddr-save","soc-spi-nor-access","presence-cpu0","s0-rtc-lock",
+			"","","",
+	/*N0-N7*/	"hpm-fw-recovery","hpm-stby-rst-n","jtag-sel-s0","led-sw-hb",
+			"jtag-dbgr-prsnt-n","","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"ps0-ac-loss-n","ps1-ac-loss-n","","","led-fault","user-mode","jtag-srst-n",
+			"led-bmc-hb",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","identify-button","led-identify","","spi-nor-access","host0-ready","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"s0-hightemp-n","s0-fault-alert","s0-sys-auth-failure-n",
+			"host0-reboot-ack-n","s0-fw-boot-ok","host0-shd-req-n",
+			"host0-shd-ack-n","s0-overtemp-n",
+	/*W0-W7*/	"ocp-aux-pwren","ocp-main-pwren","ocp-pgood","",
+			"bmc-ok","bmc-ready","spi0-program-sel","spi0-backup-sel",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","vrd-prg-en-n","","","","host0-special-boot",
+	/*Z0-Z7*/	"","ps0-pgood","ps1-pgood","","","","","";
+
+	ocp-aux-pwren-hog {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(W, 0) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "ocp-aux-pwren";
+	};
+
+};
+
+&gpio1 {
+	gpio-line-names =
+	/*18A0-18A7*/	"","","","","","","","",
+	/*18B0-18B7*/	"","","","","s0-soc-pgood","vga-ft-press-n","emmc-rst-n","s01-uart1-sel",
+	/*18C0-18C7*/	"uart1-mode0","uart1-mode1","uart2-mode0","uart2-mode1",
+			"","","","",
+	/*18D0-18D7*/	"","","","","","","","",
+	/*18E0-18E3*/	"","","","";
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtmitchell.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtmitchell.dts
new file mode 100644
index 000000000000..2b336aa0146d
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ampere-mtmitchell.dts
@@ -0,0 +1,1061 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (c) 2022, Ampere Computing LLC
+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+	model = "Ampere Mt.Mitchell BMC";
+	compatible = "ampere,mtmitchell-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial7 = &uart8;
+		serial8 = &uart9;
+
+		/*
+		 * I2C temperature alias port
+		 */
+		i2c20 = &i2c4_bus70_chn0;
+		i2c21 = &i2c4_bus70_chn1;
+		i2c22 = &i2c4_bus70_chn2;
+		i2c23 = &i2c4_bus70_chn3;
+
+		/*
+		 *  i2c bus 30-31 assigned to OCP slot 0-1
+		 */
+		i2c30 = &ocpslot_0;
+		i2c31 = &ocpslot_1;
+
+		/*
+		 *  i2c bus 32-33 assigned to Riser slot 0-1
+		 */
+		i2c32 = &i2c_riser0;
+		i2c33 = &i2c_riser1;
+
+		/*
+		 *  i2c bus 38-39 assigned to FRU on Riser slot 0-1
+		 */
+		i2c38 = &i2c_riser0_chn_0;
+		i2c39 = &i2c_riser1_chn_0;
+
+		/*
+		 *  I2C NVMe alias port
+		 */
+		i2c100 = &backplane_0;
+		i2c48 = &nvmeslot_0;
+		i2c49 = &nvmeslot_1;
+		i2c50 = &nvmeslot_2;
+		i2c51 = &nvmeslot_3;
+		i2c52 = &nvmeslot_4;
+		i2c53 = &nvmeslot_5;
+		i2c54 = &nvmeslot_6;
+		i2c55 = &nvmeslot_7;
+
+		i2c101 = &backplane_1;
+		i2c56 = &nvmeslot_8;
+		i2c57 = &nvmeslot_9;
+		i2c58 = &nvmeslot_10;
+		i2c59 = &nvmeslot_11;
+		i2c60 = &nvmeslot_12;
+		i2c61 = &nvmeslot_13;
+		i2c62 = &nvmeslot_14;
+		i2c63 = &nvmeslot_15;
+
+		i2c102 = &backplane_2;
+		i2c64 = &nvmeslot_16;
+		i2c65 = &nvmeslot_17;
+		i2c66 = &nvmeslot_18;
+		i2c67 = &nvmeslot_19;
+		i2c68 = &nvmeslot_20;
+		i2c69 = &nvmeslot_21;
+		i2c70 = &nvmeslot_22;
+		i2c71 = &nvmeslot_23;
+
+		i2c80 = &nvme_m2_0;
+		i2c81 = &nvme_m2_1;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		gfx_memory: framebuffer {
+			size = <0x01000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+
+		video_engine_memory: video {
+			size = <0x04000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+
+		vga_memory: region@bf000000 {
+			no-map;
+			compatible = "shared-dma-pool";
+			reg = <0xbf000000 0x01000000>;  /* 16M */
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		/*
+		 * Use gpio-leds to configure GPIOW5 (bmc-ready) pin to be reseted when
+		 * watchdog timeout.
+		 */
+		led-bmc-ready {
+			gpios = <&gpio0 ASPEED_GPIO(W, 5) (GPIO_ACTIVE_HIGH | GPIO_TRANSITORY)>;
+		};
+
+		led-sw-heartbeat {
+			gpios = <&gpio0 ASPEED_GPIO(N, 3) GPIO_ACTIVE_HIGH>;
+		};
+
+		led-identify {
+			gpios = <&gpio0 ASPEED_GPIO(S, 3) GPIO_ACTIVE_HIGH>;
+		};
+
+		led-fault {
+			gpios = <&gpio0 ASPEED_GPIO(P, 4) GPIO_ACTIVE_HIGH>;
+		};
+
+		led-fan-fault {
+			gpios = <&gpio_expander1 0 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-psu-fault {
+			gpios = <&gpio_expander1 1 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	voltage_mon_reg: voltage-mon-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "ltc2497_reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	gpioI5mux: mux-controller {
+		compatible = "gpio-mux";
+		#mux-control-cells = <0>;
+		mux-gpios = <&gpio0 ASPEED_GPIO(I, 5) GPIO_ACTIVE_HIGH>;
+	};
+
+	adc0mux: adc0mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 0>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc1mux: adc1mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 1>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc2mux: adc2mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 2>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc3mux: adc3mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 3>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc4mux: adc4mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 4>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc5mux: adc5mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 5>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc6mux: adc6mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 6>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc7mux: adc7mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 7>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc8mux: adc8mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 8>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc9mux: adc9mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 9>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc10mux: adc10mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 10>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc11mux: adc11mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 11>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc12mux: adc12mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 12>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc13mux: adc13mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 13>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc14mux: adc14mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 14>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	adc15mux: adc15mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc_i2c_0 15>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		settle-time-us = <10000>;
+		channels = "s0", "s1";
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels =	<&adc0mux 0>, <&adc0mux 1>,
+				<&adc1mux 0>, <&adc1mux 1>,
+				<&adc2mux 0>, <&adc2mux 1>,
+				<&adc3mux 0>, <&adc3mux 1>,
+				<&adc4mux 0>, <&adc4mux 1>,
+				<&adc5mux 0>, <&adc5mux 1>,
+				<&adc6mux 0>, <&adc6mux 1>,
+				<&adc7mux 0>, <&adc7mux 1>,
+				<&adc8mux 0>, <&adc8mux 1>,
+				<&adc9mux 0>, <&adc9mux 1>,
+				<&adc10mux 0>, <&adc10mux 1>,
+				<&adc11mux 0>, <&adc11mux 1>,
+				<&adc12mux 0>, <&adc12mux 1>,
+				<&adc13mux 0>, <&adc13mux 1>,
+				<&adc14mux 0>, <&adc14mux 1>,
+				<&adc15mux 0>, <&adc15mux 1>,
+				<&adc_i2c_1 0>, <&adc_i2c_1 1>,
+				<&adc_i2c_1 2>, <&adc_i2c_1 3>,
+				<&adc_i2c_1 4>, <&adc_i2c_1 5>,
+				<&adc_i2c_1 6>, <&adc_i2c_1 7>,
+				<&adc_i2c_1 8>, <&adc_i2c_1 9>,
+				<&adc_i2c_1 10>, <&adc_i2c_1 11>,
+				<&adc_i2c_1 12>, <&adc_i2c_1 13>,
+				<&adc_i2c_1 14>, <&adc_i2c_1 15>,
+				<&adc0 0>, <&adc0 1>,
+				<&adc0 2>;
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mac0 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii1_default>;
+};
+
+&mac3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64.dtsi"
+	};
+
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "alt-bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64-alt.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "pnor";
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&uart8 {
+	status = "okay";
+};
+
+&uart9 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	temperature-sensor@2e {
+		compatible = "adi,adt7490";
+		reg = <0x2e>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+
+	psu@58 {
+		compatible = "pmbus";
+		reg = <0x58>;
+	};
+
+	psu@59 {
+		compatible = "pmbus";
+		reg = <0x59>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+	bus-frequency = <1000000>;
+	multi-master;
+	mctp-controller;
+
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+
+	adc_i2c_0: adc@14 {
+		compatible = "lltc,ltc2497";
+		reg = <0x14>;
+		vref-supply = <&voltage_mon_reg>;
+		#io-channel-cells = <1>;
+	 };
+
+	adc_i2c_1: adc@16 {
+		compatible = "lltc,ltc2497";
+		reg = <0x16>;
+		vref-supply = <&voltage_mon_reg>;
+		#io-channel-cells = <1>;
+	 };
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9545";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		i2c4_bus70_chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+
+			outlet_temp1: temperature-sensor@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+			psu1_inlet_temp2: temperature-sensor@49 {
+				compatible = "ti,tmp75";
+				reg = <0x49>;
+			};
+		};
+
+		i2c4_bus70_chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+
+			pcie_zone_temp1: temperature-sensor@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+			psu0_inlet_temp2: temperature-sensor@49 {
+				compatible = "ti,tmp75";
+				reg = <0x49>;
+			};
+		};
+
+		i2c4_bus70_chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+
+			pcie_zone_temp2: temperature-sensor@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+			outlet_temp2: temperature-sensor@49 {
+				compatible = "ti,tmp75";
+				reg = <0x49>;
+			};
+		};
+
+		i2c4_bus70_chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+
+			mb_inlet_temp1: temperature-sensor@7c {
+				compatible = "microchip,emc1413";
+				reg = <0x7c>;
+			};
+			mb_inlet_temp2: temperature-sensor@4c {
+				compatible = "microchip,emc1413";
+				reg = <0x4c>;
+			};
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		ocpslot_0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+
+			ocpslot_0_temp: temperature-sensor@1f {
+				compatible = "ti,tmp421";
+				reg = <0x1f>;
+			};
+		};
+
+		ocpslot_1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+
+			ocpslot_1_temp: temperature-sensor@1f {
+				compatible = "ti,tmp421";
+				reg = <0x1f>;
+			};
+		};
+
+		i2c_riser0: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+
+			i2c-mux@72 {
+				compatible = "nxp,pca9546";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x72>;
+				i2c-mux-idle-disconnect;
+
+				i2c_riser0_chn_0: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x0>;
+
+					eeprom@50 {
+						compatible = "atmel,24c02";
+						reg = <0x50>;
+						pagesize = <16>;
+					};
+				};
+			};
+		};
+
+		i2c_riser1: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+
+			i2c-mux@72 {
+				compatible = "nxp,pca9546";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x72>;
+				i2c-mux-idle-disconnect;
+
+				i2c_riser1_chn_0: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x0>;
+
+					eeprom@50 {
+						compatible = "atmel,24c02";
+						reg = <0x50>;
+						pagesize = <16>;
+					};
+				};
+			};
+		};
+	};
+};
+
+&i2c6 {
+	status = "okay";
+	rtc@51 {
+		compatible = "nxp,pcf85063a";
+		reg = <0x51>;
+	};
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+
+	temperature-sensor@48 {
+		compatible = "ti,tmp112";
+		reg = <0x48>;
+	};
+
+	gpio@77 {
+		compatible = "nxp,pca9539";
+		reg = <0x77>;
+		gpio-controller;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"ext-vref-sel","","presence-hdd-bp5-n","presence-hdd-bp6-n",
+		"","bmc-riser-en-n","bmc-ocp1-en-n","bmc-ocp0-en-n",
+		"","","","",
+		"","","","";
+
+		bmc-ocp0-en-hog {
+			gpio-hog;
+			gpios = <7 GPIO_ACTIVE_LOW>;
+			output-high;
+			line-name = "bmc-ocp0-en-n";
+		};
+	};
+
+	fan-controller0@20 {
+		compatible = "maxim,max31790";
+		reg = <0x20>;
+	};
+
+	fan-controller1@2f {
+		compatible = "maxim,max31790";
+		reg = <0x2f>;
+	};
+};
+
+&i2c9 {
+	status = "okay";
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		backplane_1: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+				pagesize = <32>;
+			};
+
+			i2c-mux@71 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x71>;
+				i2c-mux-idle-disconnect;
+
+				nvmeslot_8: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x0>;
+				};
+				nvmeslot_9: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x1>;
+				};
+				nvmeslot_10: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x2>;
+				};
+				nvmeslot_11: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x3>;
+				};
+				nvmeslot_12: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x4>;
+				};
+				nvmeslot_13: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x5>;
+				};
+				nvmeslot_14: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x6>;
+				};
+				nvmeslot_15: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x7>;
+				};
+			};
+
+			tmp432@4c {
+				compatible = "ti,tmp75";
+				reg = <0x4c>;
+			};
+		};
+
+		backplane_2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+				pagesize = <32>;
+			};
+
+			i2c-mux@71 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x71>;
+				i2c-mux-idle-disconnect;
+
+				nvmeslot_16: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x0>;
+				};
+				nvmeslot_17: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x1>;
+				};
+				nvmeslot_18: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x2>;
+				};
+				nvmeslot_19: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x3>;
+				};
+				nvmeslot_20: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x4>;
+				};
+				nvmeslot_21: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x5>;
+				};
+				nvmeslot_22: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x6>;
+				};
+				nvmeslot_23: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x7>;
+				};
+			};
+
+			tmp432@4c {
+				compatible = "ti,tmp75";
+				reg = <0x4c>;
+			};
+		};
+
+		backplane_0: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x4>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+				pagesize = <32>;
+			};
+
+			i2c-mux@71 {
+				compatible = "nxp,pca9548";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x71>;
+				i2c-mux-idle-disconnect;
+
+				nvmeslot_0: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x0>;
+				};
+				nvmeslot_1: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x1>;
+				};
+				nvmeslot_2: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x2>;
+				};
+				nvmeslot_3: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x3>;
+				};
+				nvmeslot_4: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x4>;
+				};
+				nvmeslot_5: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x5>;
+				};
+				nvmeslot_6: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x6>;
+				};
+				nvmeslot_7: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x7>;
+				};
+			};
+
+			tmp432@4c {
+				compatible = "ti,tmp75";
+				reg = <0x4c>;
+			};
+		};
+
+		i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x7>;
+
+			i2c-mux@71 {
+				compatible = "nxp,pca9546";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x71>;
+				i2c-mux-idle-disconnect;
+
+				nvme_m2_0: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x0>;
+				};
+
+				nvme_m2_1: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0x1>;
+				};
+			};
+		};
+	};
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+	ssif-bmc@10 {
+		compatible = "ssif-bmc";
+		reg = <0x10>;
+	};
+};
+
+&i2c14 {
+	status = "okay";
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	bmc_ast2600_cpu: temperature-sensor@35 {
+		compatible = "ti,tmp175";
+		reg = <0x35>;
+	};
+};
+
+&i2c15 {
+	status = "okay";
+	gpio_expander1: gpio-expander@22 {
+		compatible = "nxp,pca9535";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+			"fan-fault","psu-fault",
+			"","",
+			"","",
+			"gpi0","gpi1",
+			"","",
+			"","",
+			"","",
+			"","";
+	};
+};
+
+&adc0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+		&pinctrl_adc2_default>;
+};
+
+&vhub {
+	status = "okay";
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+&gpio0 {
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","i2c2-reset-n","i2c6-reset-n","i2c4-reset-n",
+	/*B0-B7*/	"","","","","host0-sysreset-n","host0-pmin-n","","",
+	/*C0-C7*/	"s0-vrd-fault-n","s1-vrd-fault-n","bmc-debug-mode","",
+			"irq-n","","vrd-sel","spd-sel",
+	/*D0-D7*/	"presence-ps0","presence-ps1","hsc-12vmain-alt2-n","ext-high-temp-n",
+			"","bmc-ncsi-txen","","",
+	/*E0-E7*/	"","eth-phy-int-n","clk50m-bmc-ncsi","","","","","",
+	/*F0-F7*/	"s0-pcp-oc-warn-n","s1-pcp-oc-warn-n","power-chassis-control",
+			"cpu-bios-recover","s0-heartbeat","hs-csout-prochot",
+			"s0-vr-hot-n","s1-vr-hot-n",
+	/*G0-G7*/	"","","hsc-12vmain-alt1-n","","","","","",
+	/*H0-H7*/	"jtag-program-sel","fpga-program-b","wd-disable-n",
+			"power-chassis-good","","","","",
+	/*I0-I7*/	"","","","","","adc-sw","power-button","rtc-battery-voltage-read-enable",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","s0-ddr-save","soc-spi-nor-access","presence-cpu0",
+			"s0-rtc-lock","","","",
+	/*N0-N7*/	"hpm-fw-recovery","hpm-stby-rst-n","jtag-sel-s0","led-sw-hb",
+			"jtag-dbgr-prsnt-n","s1-heartbeat","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"ps0-ac-loss-n","ps1-ac-loss-n","","",
+			"led-fault","cpld-user-mode","jtag-srst-n","led-bmc-hb",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","identify-button","led-identify",
+			"s1-ddr-save","spi-nor-access","host0-ready","presence-cpu1",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"s0-hightemp-n","s0-fault-alert","s0-sys-auth-failure-n",
+			"host0-reboot-ack-n","s0-fw-boot-ok","host0-shd-req-n",
+			"host0-shd-ack-n","s0-overtemp-n",
+	/*W0-W7*/	"ocp-aux-pwren","ocp-main-pwren","ocp-pgood","s1-pcp-pgood",
+			"bmc-ok","bmc-ready","spi0-program-sel","spi0-backup-sel",
+	/*X0-X7*/	"i2c-backup-sel","s1-fault-alert","s1-fw-boot-ok",
+			"s1-hightemp-n","s0-spi-auth-fail-n","s1-sys-auth-failure-n",
+			"s1-overtemp-n","cpld-s1-spi-auth-fail-n",
+	/*Y0-Y7*/	"","","","","","","","host0-special-boot",
+	/*Z0-Z7*/	"reset-button","ps0-pgood","ps1-pgood","","","","","";
+
+	ocp-aux-pwren-hog {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(W, 0) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "ocp-aux-pwren";
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+	/*18A0-18A7*/	"","","","","","","","",
+	/*18B0-18B7*/	"","","","","","","s0-soc-pgood","",
+	/*18C0-18C7*/	"uart1-mode0","uart1-mode1","uart2-mode0","uart2-mode1",
+			"uart3-mode0","uart3-mode1","uart4-mode0","uart4-mode1",
+	/*18D0-18D7*/	"","","","","","","","",
+	/*18E0-18E3*/	"","","","";
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-arm-stardragon4800-rep2.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-arm-stardragon4800-rep2.dts
index 7c6af7f226e7..b550a48f48f0 100644
--- a/arch/arm/boot/dts/aspeed-bmc-arm-stardragon4800-rep2.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-arm-stardragon4800-rep2.dts
@@ -171,7 +171,7 @@
 				reg = <0x50>;
 			};
 			dps650ab@58 {
-				compatible = "dps650ab";
+				compatible = "delta,dps650ab";
 				reg = <0x58>;
 			};
 		};
@@ -200,18 +200,14 @@
 	status = "okay";
 };
 
-&pinctrl {
-	aspeed,external-nodes = <&gfx &lhc>;
-};
-
 &gpio {
-	pin_gpio_c7 {
+	pin-gpio-c7-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(C, 7) GPIO_ACTIVE_HIGH>;
 		output-low;
 		line-name = "BIOS_SPI_MUX_S";
 	};
-	pin_gpio_d1 {
+	pin-gpio-d1-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(D, 1) GPIO_ACTIVE_HIGH>;
 		output-high;
diff --git a/arch/arm/boot/dts/aspeed-bmc-asrock-e3c246d4i.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-asrock-e3c246d4i.dts
index 9b4cf5ebe6d5..3ebd80db06f9 100644
--- a/arch/arm/boot/dts/aspeed-bmc-asrock-e3c246d4i.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-asrock-e3c246d4i.dts
@@ -63,7 +63,7 @@
 		status = "okay";
 		m25p,fast-read;
 		label = "bmc";
-		spi-max-frequency = <100000000>; /* 100 MHz */
+		spi-max-frequency = <50000000>; /* 50 MHz */
 #include "openbmc-flash-layout.dtsi"
 	};
 };
@@ -83,6 +83,9 @@
 
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_rgmii1_default &pinctrl_mdio1_default>;
+
+	nvmem-cells = <&eth0_macaddress>;
+	nvmem-cell-names = "mac-address";
 };
 
 &i2c1 {
@@ -103,6 +106,16 @@
 		compatible = "st,24c128", "atmel,24c128";
 		reg = <0x57>;
 		pagesize = <16>;
+
+		nvmem-layout {
+			compatible = "fixed-layout";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			eth0_macaddress: macaddress@3f80 {
+				reg = <0x3f80 6>;
+			};
+		};
 	};
 };
 
@@ -173,7 +186,7 @@
 			"CK_33M_BMC", "LFRAME", "SERIRQ", "S_PLTRST";
 
 	/* Assert BMC_READY so BIOS doesn't sit around waiting for it */
-	bmc-ready {
+	bmc-ready-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(J, 0) GPIO_ACTIVE_LOW>;
 		output-high;
@@ -202,3 +215,7 @@
 	status = "okay";
 	aspeed,lpc-io-reg = <0xca2>;
 };
+
+&peci0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-asrock-e3c256d4i.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-asrock-e3c256d4i.dts
new file mode 100644
index 000000000000..8c57a071f488
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-asrock-e3c256d4i.dts
@@ -0,0 +1,326 @@
+// SPDX-License-Identifier: GPL-2.0+
+/dts-v1/;
+
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/watchdog/aspeed-wdt.h>
+
+/{
+	model = "ASRock E3C256D4I BMC";
+	compatible = "asrock,e3c256d4i-bmc", "aspeed,ast2500";
+
+	aliases {
+		serial4 = &uart5;
+
+		i2c20 = &i2c2mux0ch0;
+		i2c21 = &i2c2mux0ch1;
+		i2c22 = &i2c2mux0ch2;
+		i2c23 = &i2c2mux0ch3;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x20000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		/* BMC heartbeat */
+		led-0 {
+			gpios = <&gpio ASPEED_GPIO(H, 6) GPIO_ACTIVE_LOW>;
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_GREEN>;
+			linux,default-trigger = "timer";
+		};
+
+		/* system fault */
+		led-1 {
+			gpios = <&gpio ASPEED_GPIO(Z, 2) GPIO_ACTIVE_LOW>;
+			function = LED_FUNCTION_FAULT;
+			color = <LED_COLOR_ID_RED>;
+			panic-indicator;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
+			<&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>,
+			<&adc 8>, <&adc 9>, <&adc 10>, <&adc 11>,
+			<&adc 12>, <&adc 13>, <&adc 14>, <&adc 15>;
+	};
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <100000000>; /* 100 MHz */
+#include "openbmc-flash-layout-64.dtsi"
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&uart_routing {
+	status = "okay";
+};
+
+&mac0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii1_default &pinctrl_mdio1_default>;
+
+	nvmem-cells = <&eth0_macaddress>;
+	nvmem-cell-names = "mac-address";
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9545";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c2mux0ch0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c2mux0ch1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		i2c2mux0ch2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c2mux0ch3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+
+	vrm@60 {
+		compatible = "isil,isl69269";
+		reg = <0x60>;
+	};
+};
+
+&i2c12 {
+	status = "okay";
+
+	/* FRU eeprom */
+	eeprom@57 {
+		compatible = "st,24c128", "atmel,24c128";
+		reg = <0x57>;
+		pagesize = <16>;
+
+		nvmem-layout {
+			compatible = "fixed-layout";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			eth0_macaddress: macaddress@3f80 {
+				reg = <0x3f80 6>;
+			};
+		};
+	};
+};
+
+&video {
+	status = "okay";
+};
+
+&vhub {
+	status = "okay";
+};
+
+&lpc_ctrl {
+	status = "okay";
+};
+
+&lpc_snoop {
+	status = "okay";
+	snoop-ports = <0x80>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+};
+
+&peci0 {
+	status = "okay";
+};
+
+&wdt1 {
+	aspeed,reset-mask = <(AST2500_WDT_RESET_DEFAULT & ~AST2500_WDT_RESET_LPC)>;
+};
+
+&wdt2 {
+	aspeed,reset-mask = <(AST2500_WDT_RESET_DEFAULT & ~AST2500_WDT_RESET_LPC)>;
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_default /* CPU */
+		&pinctrl_pwm2_default      /* rear */
+		&pinctrl_pwm4_default>;    /* front */
+
+	/* CPU */
+	fan@0 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x00>;
+	};
+
+	/* rear */
+	fan@2 {
+		reg = <0x02>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x02>;
+	};
+
+	/* front */
+	fan@4 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x04>;
+	};
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names =
+		/*  A */ "", "", "NMI_BTN_N", "BMC_NMI", "", "", "", "",
+		/*  B */ "", "", "", "", "", "", "", "",
+		/*  C */ "", "", "", "", "", "", "", "",
+		/*  D */ "BMC_PSIN", "BMC_PSOUT", "BMC_RESETCON", "RESETCON",
+			"", "", "", "",
+		/*  E */ "", "", "", "", "", "", "", "",
+		/*  F */ "LOCATORLED_STATUS_N", "LOCATORBTN", "", "",
+			"", "", "BMC_PCH_SCI_LPC", "BMC_NCSI_MUX_CTL",
+		/*  G */ "HWM_BAT_EN", "CHASSIS_ID0", "CHASSIS_ID1", "CHASSIS_ID2",
+			"", "", "", "",
+		/*  H */ "FM_ME_RCVR_N", "O_PWROK", "", "D4_DIMM_EVENT_3V_N",
+			"MFG_MODE_N", "BMC_RTCRST", "BMC_HB_LED_N", "BMC_CASEOPEN",
+		/*  I */ "", "", "", "", "", "", "", "",
+		/*  J */ "BMC_READY", "BMC_PCH_BIOS_CS_N", "BMC_SMI", "", "", "", "", "",
+		/*  K */ "", "", "", "", "", "", "", "",
+		/*  L */ "", "", "", "", "", "", "", "",
+		/*  M */ "", "", "", "", "", "", "", "",
+		/*  N */ "", "", "", "", "", "", "", "",
+		/*  O */ "", "", "", "", "", "", "", "",
+		/*  P */ "", "", "", "", "", "", "", "",
+		/*  Q */ "", "", "", "", "", "", "", "",
+		/*  R */ "", "", "", "", "", "", "", "",
+		/*  S */ "PCHHOT_BMC_N", "", "RSMRST", "", "", "", "", "",
+		/*  T */ "", "", "", "", "", "", "", "",
+		/*  U */ "", "", "", "", "", "", "", "",
+		/*  V */ "", "", "", "", "", "", "", "",
+		/*  W */ "", "", "", "", "", "", "", "",
+		/*  X */ "", "", "", "", "", "", "", "",
+		/*  Y */ "SLP_S3", "SLP_S5", "", "", "", "", "", "",
+		/*  Z */ "CPU_CATERR_BMC_N", "", "SYSTEM_FAULT_LED_N", "BMC_THROTTLE_N",
+			"", "", "", "",
+		/* AA */ "CPU1_THERMTRIP_LATCH_N", "", "CPU1_PROCHOT_N", "",
+			"", "", "IRQ_SMI_ACTIVE_N", "FM_BIOS_POST_CMPLT_N",
+		/* AB */ "", "", "ME_OVERRIDE", "BMC_DMI_MODIFY", "", "", "", "",
+		/* AC */ "", "", "", "", "", "", "", "";
+};
+
+&adc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default /* 3VSB */
+		&pinctrl_adc1_default	   /* 5VSB */
+		&pinctrl_adc2_default	   /* CPU1 */
+		&pinctrl_adc3_default	   /* VCCSA */
+		&pinctrl_adc4_default	   /* VCCM */
+		&pinctrl_adc5_default	   /* V10M */
+		&pinctrl_adc6_default	   /* VCCIO */
+		&pinctrl_adc7_default	   /* VCCGT */
+		&pinctrl_adc8_default	   /* VPPM */
+		&pinctrl_adc9_default	   /* BAT */
+		&pinctrl_adc10_default	   /* 3V */
+		&pinctrl_adc11_default	   /* 5V */
+		&pinctrl_adc12_default	   /* 12V */
+		&pinctrl_adc13_default	   /* GND */
+		&pinctrl_adc14_default	   /* GND */
+		&pinctrl_adc15_default>;   /* GND */
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-asrock-romed8hm3.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-asrock-romed8hm3.dts
index e71ccfd1df63..e306655ce4a3 100644
--- a/arch/arm/boot/dts/aspeed-bmc-asrock-romed8hm3.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-asrock-romed8hm3.dts
@@ -31,7 +31,7 @@
 		};
 
 		system-fault {
-			gpios = <&gpio ASPEED_GPIO(Z, 2) GPIO_ACTIVE_LOW>;
+			gpios = <&gpio ASPEED_GPIO(Z, 2) GPIO_ACTIVE_HIGH>;
 			panic-indicator;
 		};
 	};
@@ -51,7 +51,7 @@
 		status = "okay";
 		m25p,fast-read;
 		label = "bmc";
-		spi-max-frequency = <100000000>; /* 100 MHz */
+		spi-max-frequency = <50000000>; /* 50 MHz */
 #include "openbmc-flash-layout-64.dtsi"
 	};
 };
@@ -71,6 +71,9 @@
 
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_rgmii1_default &pinctrl_mdio1_default>;
+
+	nvmem-cells = <&eth0_macaddress>;
+	nvmem-cell-names = "mac-address";
 };
 
 &i2c0 {
@@ -98,14 +101,16 @@
 
 	/* IPB PMIC */
 	lm25066@40 {
-		compatible = "lm25066";
+		compatible = "ti,lm25066";
 		reg = <0x40>;
+		shunt-resistor-micro-ohms = <1000>;
 	};
 
 	/* 12VSB PMIC */
 	lm25066@41 {
-		compatible = "lm25066";
+		compatible = "ti,lm25066";
 		reg = <0x41>;
+		shunt-resistor-micro-ohms = <10000>;
 	};
 };
 
@@ -129,6 +134,16 @@
 		compatible = "st,24c128", "atmel,24c128";
 		reg = <0x50>;
 		pagesize = <16>;
+
+		nvmem-layout {
+			compatible = "fixed-layout";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			eth0_macaddress: macaddress@3f80 {
+				reg = <0x3f80 6>;
+			};
+		};
 	};
 };
 
@@ -196,7 +211,7 @@
 	gpio-line-names =
 		/*  A */ "LOCATORLED_STATUS_N", "BMC_MAC2_INTB", "NMI_BTN_N", "BMC_NMI",
 			"", "", "", "",
-		/*  B */ "DDR_MEM_TEMP", "", "", "", "", "", "", "",
+		/*  B */ "POST_COMPLETE_N", "", "", "", "", "", "", "",
 		/*  C */ "", "", "", "", "PCIE_HP_SEL_N", "PCIE_SATA_SEL_N", "LOCATORBTN", "",
 		/*  D */ "BMC_PSIN", "BMC_PSOUT", "BMC_RESETCON", "RESETCON",
 			"", "", "", "PSU_FAN_FAIL_N",
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-asrock-spc621d8hm3.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-asrock-spc621d8hm3.dts
new file mode 100644
index 000000000000..c4097e4f2ca4
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-asrock-spc621d8hm3.dts
@@ -0,0 +1,328 @@
+// SPDX-License-Identifier: GPL-2.0+
+/dts-v1/;
+
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/leds/common.h>
+
+/{
+	model = "ASRock SPC621D8HM3 BMC";
+	compatible = "asrock,spc621d8hm3-bmc", "aspeed,ast2500";
+
+	aliases {
+		serial4 = &uart5;
+
+		i2c20 = &i2c1mux0ch0;
+		i2c21 = &i2c1mux0ch1;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x20000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		/* BMC heartbeat */
+		led-0 {
+			gpios = <&gpio ASPEED_GPIO(H, 6) GPIO_ACTIVE_LOW>;
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_GREEN>;
+			linux,default-trigger = "timer";
+		};
+
+		/* system fault */
+		led-1 {
+			gpios = <&gpio ASPEED_GPIO(Z, 2) GPIO_ACTIVE_LOW>;
+			function = LED_FUNCTION_FAULT;
+			color = <LED_COLOR_ID_RED>;
+			panic-indicator;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
+			<&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>,
+			<&adc 8>, <&adc 9>, <&adc 10>, <&adc 11>,
+			<&adc 12>, <&adc 13>, <&adc 14>, <&adc 15>;
+	};
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>; /* 50 MHz */
+#include "openbmc-flash-layout-64.dtsi"
+	};
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&vuart {
+	status = "okay";
+	aspeed,lpc-io-reg = <0x2f8>;
+	aspeed,lpc-interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&mac0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii1_default &pinctrl_mdio1_default>;
+
+	nvmem-cells = <&eth0_macaddress>;
+	nvmem-cell-names = "mac-address";
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+
+	/* hardware monitor/thermal sensor */
+	temperature-sensor@29 {
+		compatible = "nuvoton,nct7802";
+		reg = <0x29>;
+	};
+
+	/* motherboard temp sensor (TMP1, near BMC) */
+	temperature-sensor@4c {
+		compatible = "nuvoton,w83773g";
+		reg = <0x4c>;
+	};
+
+	/* motherboard FRU eeprom */
+	eeprom@50 {
+		compatible = "st,24c128", "atmel,24c128";
+		reg = <0x50>;
+		pagesize = <16>;
+
+		nvmem-layout {
+			compatible = "fixed-layout";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			eth0_macaddress: macaddress@3f80 {
+				reg = <0x3f80 6>;
+			};
+		};
+	};
+
+	/* M.2 slot smbus mux */
+	i2c-mux@71 {
+		compatible = "nxp,pca9545";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c1mux0ch0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c1mux0ch1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+	};
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+};
+
+&i2c12 {
+	status = "okay";
+};
+
+&i2c13 {
+	status = "okay";
+};
+
+&video {
+	status = "okay";
+};
+
+&vhub {
+	status = "okay";
+};
+
+&lpc_ctrl {
+	status = "okay";
+};
+
+&lpc_snoop {
+	status = "okay";
+	snoop-ports = <0x80>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+};
+
+&peci0 {
+	status = "okay";
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_default
+		&pinctrl_pwm2_default
+		&pinctrl_pwm3_default
+		&pinctrl_pwm4_default>;
+
+	fan@0 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x00>;
+	};
+
+	fan@2 {
+		reg = <0x02>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x02>;
+	};
+
+	fan@3 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x03>;
+	};
+
+	fan@4 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x04>;
+	};
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names =
+		/*  A */ "LOCATORLED_STATUS_N", "LOCATORBTN_N",
+			"BMC_READY_N", "FM_SPD_DDRCPU_LVLSHFT_EN",
+			"", "", "", "",
+		/*  B */ "NODE_ID_1", "NODE_ID_2", "PSU_FAN_FAIL_N", "",
+			"", "", "", "GPIO_RST",
+		/*  C */ "", "", "", "", "", "", "", "",
+		/*  D */ "FP_PWR_BTN_MUX_N", "FM_BMC_PWRBTN_OUT_N",
+			"FP_RST_BTN_N", "RST_BMC_RSTBTN_OUT_N",
+			"NMI_BTN_N", "BMC_NMI",
+			"", "",
+		/*  E */ "", "", "", "FM_ME_RCVR_N", "", "", "", "",
+		/*  F */ "BMC_SMB_SEL_N", "FM_CPU2_DISABLE_COD_N",
+			"FM_REMOTE_DEBUG_BMC_EN", "FM_CPU_ERR0_LVT3_EN",
+			"FM_CPU_ERR1_LVT3_EN", "FM_CPU_ERR2_LVT3_EN",
+			"FM_MEM_THERM_EVENT_CPU1_LVT3_N", "FM_MEM_THERM_EVENT_CPU2_LVT3_N",
+		/*  G */ "HWM_BAT_EN", "", "BMC_PHYRST_N", "FM_BIOS_SPI_BMC_CTRL",
+			"BMC_ALERT1_N", "BMC_ALERT2_N", "BMC_ALERT3_N", "IRQ_SML0_ALERT_N",
+		/*  H */ "BMC_SMB_PRESENT_1_N", "FM_PCH_CORE_VID_0", "FM_PCH_CORE_VID_1", "",
+			"FM_MFG_MODE", "BMC_RTCRST", "BMC_HB_LED_N", "BMC_CASEOPEN",
+		/*  I */ "IRQ_PVDDQ_ABCD_CPU1_VRHOT_LVC3_N", "IRQ_PVDDQ_ABCD_CPU2_VRHOT_LVC3_N",
+			"IRQ_PVDDQ_EFGH_CPU1_VRHOT_LVC3_N", "IRQ_PVDDQ_EFGH_CPU2_VRHOT_LVC3_N",
+			"", "", "", "",
+		/*  J */ "", "", "", "", "", "", "", "",
+		/*  K */ "", "", "", "", "", "", "", "",
+		/*  L */ "", "", "", "", "", "", "", "",
+		/*  M */ "FM_PVCCIN_CPU1_PWR_IN_ALERT_N", "FM_PVCCIN_CPU2_PWR_IN_ALERT_N",
+			"IRQ_PVCCIN_CPU1_VRHOT_LVC3_N", "IRQ_PVCCIN_CPU2_VRHOT_LVC3_N",
+			"FM_CPU1_PROCHOT_BMC_LVC3_N", "",
+			"FM_CPU1_MEMHOT_OUT_N", "FM_CPU2_MEMHOT_OUT_N",
+		/*  N */ "", "", "", "", "", "", "", "",
+		/*  O */ "", "", "", "", "", "", "", "",
+		/*  P */ "", "", "", "", "", "", "", "",
+		/*  Q */ "", "", "", "", "", "", "RST_GLB_RST_WARN_N", "PCIE_WAKE_N",
+		/*  R */ "", "", "FM_BMC_SUSACK_N", "FM_BMC_EUP_LOT6_N",
+			"", "FM_BMC_PCH_SCI_LPC_N", "", "",
+		/*  S */ "FM_DBP_PRESENT_N", "FM_CPU2_SKTOCC_LCT3_N",
+			"FM_CPU1_FIVR_FAULT_LVT3", "FM_CPU2_FIVR_FAULT_LVT3",
+			 "", "", "", "",
+		/*  T */ "", "", "", "", "", "", "", "",
+		/*  U */ "", "", "", "", "", "", "", "",
+		/*  V */ "", "", "", "", "", "", "", "",
+		/*  W */ "", "", "", "", "", "", "", "",
+		/*  X */ "", "", "", "", "", "", "", "",
+		/*  Y */ "FM_SLPS3_N", "FM_SLPS4_N", "", "FM_BMC_ONCTL_N_PLD",
+			"", "", "", "",
+		/*  Z */ "FM_CPU_MSMI_CATERR_LVT3_N", "", "SYSTEM_FAULT_LED_N", "BMC_THROTTLE_N",
+			"", "", "", "",
+		/* AA */ "FM_CPU1_THERMTRIP_LATCH_LVT3_N", "FM_CPU2_THERMTRIP_LATCH_LVT3_N",
+			"FM_BIOS_POST_COMPLT_N", "DBP_BMC_SYSPWROK",
+			"", "IRQ_SML0_ALERT_MUX_N",
+			"IRQ_SMI_ACTIVE_N", "IRQ_NMI_EVENT_N",
+		/* AB */ "FM_PCH_BMC_THERMTRIP_N", "PWRGD_SYS_PWROK",
+			"ME_OVERRIDE", "IRQ_BMC_PCH_SMI_LPC_N",
+			"", "", "", "",
+		/* AC */ "", "", "", "", "", "", "", "";
+};
+
+&adc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default /* 3VSB */
+		&pinctrl_adc1_default	   /* 5VSB */
+		&pinctrl_adc2_default	   /* CPU1 */
+		&pinctrl_adc3_default	   /* NC */
+		&pinctrl_adc4_default	   /* VCCMABCD */
+		&pinctrl_adc5_default	   /* VCCMEFGH */
+		&pinctrl_adc6_default	   /* NC */
+		&pinctrl_adc7_default	   /* NC */
+		&pinctrl_adc8_default	   /* PVNN_PCH */
+		&pinctrl_adc9_default	   /* 1P05PCH */
+		&pinctrl_adc10_default	   /* 1P8PCH */
+		&pinctrl_adc11_default	   /* BAT */
+		&pinctrl_adc12_default	   /* 3V */
+		&pinctrl_adc13_default	   /* 5V */
+		&pinctrl_adc14_default	   /* 12V */
+		&pinctrl_adc15_default>;   /* GND */
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-asrock-x570d4u.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-asrock-x570d4u.dts
new file mode 100644
index 000000000000..e61a6cb43438
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-asrock-x570d4u.dts
@@ -0,0 +1,360 @@
+// SPDX-License-Identifier: GPL-2.0+
+/dts-v1/;
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Asrock Rack X570D4U BMC";
+	compatible = "asrock,x570d4u-bmc", "aspeed,ast2500";
+
+	aliases {
+		i2c40 = &i2c4mux0ch0;
+		i2c41 = &i2c4mux0ch1;
+		i2c42 = &i2c4mux0ch2;
+		i2c43 = &i2c4mux0ch3;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		pci_memory: region@9a000000 {
+			no-map;
+			reg = <0x9a000000 0x00010000>; /* 64K */
+		};
+
+		video_engine_memory: jpegbuffer {
+			size = <0x02800000>;	/* 40M */
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+
+		gfx_memory: framebuffer {
+			size = <0x01000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			/* led-heartbeat-n */
+			gpios = <&gpio ASPEED_GPIO(H, 6) GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_HEARTBEAT;
+			linux,default-trigger = "timer";
+		};
+
+		led-1 {
+			/* led-fault-n */
+			gpios = <&gpio ASPEED_GPIO(Z, 2) GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_AMBER>;
+			function = LED_FUNCTION_FAULT;
+			panic-indicator;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>, <&adc 4>,
+			<&adc 5>, <&adc 6>, <&adc 7>, <&adc 8>, <&adc 9>,
+			<&adc 10>, <&adc 11>, <&adc 12>;
+	};
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names =
+	/*  A */ "input-locatorled-n", "", "", "", "", "", "", "",
+	/*  B */ "input-bios-post-cmplt-n", "", "", "", "", "", "", "",
+	/*  C */ "", "", "", "", "", "", "control-locatorbutton-n", "",
+	/*  D */ "button-power-n", "control-power-n", "button-reset-n",
+		 "control-reset-n", "", "", "", "",
+	/*  E */ "", "", "", "", "", "", "", "",
+	/*  F */ "", "", "", "", "", "", "", "",
+	/*  G */ "output-hwm-vbat-enable", "input-id0-n", "input-id1-n",
+		 "input-id2-n", "input-aux-smb-alert-n", "",
+		 "input-psu-smb-alert-n", "",
+	/*  H */ "", "", "", "", "input-mfg-mode-n", "",
+		 "led-heartbeat-n", "input-case-open-n",
+	/*  I */ "", "", "", "", "", "", "", "",
+	/*  J */ "output-bmc-ready-n", "", "", "", "", "", "", "",
+	/*  K */ "", "", "", "", "", "", "", "",
+	/*  L */ "", "", "", "", "", "", "", "",
+	/*  M */ "", "", "", "", "", "", "", "",
+	/*  N */ "", "", "", "", "", "", "", "",
+	/*  O */ "", "", "", "", "", "", "", "",
+	/*  P */ "", "", "", "", "", "", "", "",
+	/*  Q */ "", "", "", "", "input-bmc-smb-present-n", "", "",
+		 "input-pcie-wake-n",
+	/*  R */ "", "", "", "", "", "", "", "",
+	/*  S */ "input-bmc-pchhot-n", "", "", "", "", "", "", "",
+	/*  T */ "", "", "", "", "", "", "", "",
+	/*  U */ "", "", "", "", "", "", "", "",
+	/*  V */ "", "", "", "", "", "", "", "",
+	/*  W */ "", "", "", "", "", "", "", "",
+	/*  X */ "", "", "", "", "", "", "", "",
+	/*  Y */ "input-sleep-s3-n", "input-sleep-s5-n", "", "", "", "",
+		 "", "",
+	/*  Z */ "", "", "led-fault-n", "output-bmc-throttle-n", "", "",
+		 "", "",
+	/* AA */ "input-cpu1-thermtrip-latch-n", "",
+		 "input-cpu1-prochot-n", "", "", "", "", "",
+	/* AB */ "", "input-power-good", "", "", "", "", "", "",
+	/* AC */ "", "", "", "", "", "", "", "";
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		label = "bmc";
+		m25p,fast-read;
+		spi-max-frequency = <10000000>;
+#include "openbmc-flash-layout-64.dtsi"
+	};
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&vuart {
+	status = "okay";
+};
+
+&mac0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii1_default &pinctrl_mdio1_default>;
+
+	nvmem-cells = <&eth0_macaddress>;
+	nvmem-cell-names = "mac-address";
+};
+
+&mac1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii2_default &pinctrl_mdio2_default>;
+	use-ncsi;
+
+	nvmem-cells = <&eth1_macaddress>;
+	nvmem-cell-names = "mac-address";
+};
+
+&i2c0 {
+	/* SMBus on auxiliary panel header (AUX_PANEL1) */
+	status = "okay";
+};
+
+&i2c1 {
+	/* Hardware monitoring SMBus */
+	status = "okay";
+
+	w83773g@4c {
+		compatible = "nuvoton,w83773g";
+		reg = <0x4c>;
+	};
+};
+
+&i2c2 {
+	/* PSU SMBus (PSU_SMB1) */
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9545";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c4mux0ch0: i2c@0 {
+			/* SMBus on PCI express 16x slot */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c4mux0ch1: i2c@1 {
+			/* SMBus on PCI express 8x slot */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		i2c4mux0ch2: i2c@2 {
+			/* Unknown */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c4mux0ch3: i2c@3 {
+			/* SMBus on PCI express 1x slot */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&i2c5 {
+	/* SMBus on BMC connector (BMC_SMB_1) */
+	status = "okay";
+};
+
+&i2c7 {
+	/* FRU and SPD EEPROM SMBus */
+	status = "okay";
+
+	eeprom@57 {
+		compatible = "st,24c128", "atmel,24c128";
+		reg = <0x57>;
+		pagesize = <16>;
+
+		nvmem-layout {
+			compatible = "fixed-layout";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			eth0_macaddress: macaddress@3f80 {
+				reg = <0x3f80 6>;
+			};
+
+			eth1_macaddress: macaddress@3f88 {
+				reg = <0x3f88 6>;
+			};
+		};
+	};
+};
+
+&i2c8 {
+	/* SMBus on intelligent platform management bus header (IPMB_1) */
+	status = "okay";
+};
+
+&gfx {
+	status = "okay";
+};
+
+&vhub {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&uhci {
+	status = "okay";
+};
+
+&kcs3 {
+	aspeed,lpc-io-reg = <0xca2>;
+	status = "okay";
+};
+
+&lpc_ctrl {
+	status = "okay";
+};
+
+&lpc_snoop {
+	status = "okay";
+	snoop-ports = <0x80>;
+};
+
+&p2a {
+	status = "okay";
+	memory-region = <&pci_memory>;
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_default
+				&pinctrl_pwm1_default
+				&pinctrl_pwm2_default
+				&pinctrl_pwm3_default
+				&pinctrl_pwm4_default
+				&pinctrl_pwm5_default>;
+
+	fan@0 {
+		/* FAN1 (4-pin) */
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x00>;
+	};
+
+	fan@1 {
+		/* FAN2 (4-pin) */
+		reg = <0x01>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x01>;
+	};
+
+	fan@2 {
+		/* FAN3 (4-pin) */
+		reg = <0x02>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x02>;
+	};
+
+	fan@3 {
+		/* FAN4 (6-pin) */
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x04 0x0b>;
+	};
+
+	fan@4 {
+		/* FAN6 (6-pin) */
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x06 0x0d>;
+	};
+
+	fan@5 {
+		/* FAN5 (6-pin) */
+		reg = <0x05>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x05 0x0c>;
+	};
+};
+
+&adc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default       /* 3VSB */
+			&pinctrl_adc1_default    /* 5VSB */
+			&pinctrl_adc2_default    /* VCPU */
+			&pinctrl_adc3_default    /* VSOC */
+			&pinctrl_adc4_default    /* VCCM */
+			&pinctrl_adc5_default    /* APU-VDDP */
+			&pinctrl_adc6_default    /* PM-VDD-CLDO */
+			&pinctrl_adc7_default    /* PM-VDDCR-S5 */
+			&pinctrl_adc8_default    /* PM-VDDCR */
+			&pinctrl_adc9_default    /* VBAT */
+			&pinctrl_adc10_default   /* 3V */
+			&pinctrl_adc11_default   /* 5V */
+			&pinctrl_adc12_default>; /* 12V */
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts
new file mode 100644
index 000000000000..64f4ed07c7d2
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-asus-x4tf.dts
@@ -0,0 +1,581 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2024 ASUS Corp.
+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include "aspeed-g6-pinctrl.dtsi"
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+	model = "ASUS-X4TF";
+	compatible = "asus,x4tf-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial4 = &uart5;
+	};
+
+	chosen {
+		stdout-path = "serial4:115200n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		video_engine_memory: video {
+			size = <0x04000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+				<&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+				<&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>,
+				<&adc1 4>, <&adc1 5>, <&adc1 6>, <&adc1 7>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-heartbeat {
+			gpios = <&gpio0 ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-uid {
+			gpios = <&gpio0 ASPEED_GPIO(P, 1) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+			default-state = "off";
+		};
+
+		led-status_Y {
+			gpios = <&gpio1 ASPEED_GPIO(B, 1) GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-sys_boot_status {
+			gpios = <&gpio1 ASPEED_GPIO(B, 0) GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+};
+
+&adc0 {
+	vref = <2500>;
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+		&pinctrl_adc2_default &pinctrl_adc3_default
+		&pinctrl_adc4_default &pinctrl_adc5_default
+		&pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+	vref = <2500>;
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+		&pinctrl_adc10_default &pinctrl_adc11_default
+		&pinctrl_adc12_default &pinctrl_adc13_default
+		&pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&peci0 {
+	status = "okay";
+};
+
+&lpc_snoop {
+	snoop-ports = <0x80>;
+	status = "okay";
+};
+
+&mac2 {
+	status = "okay";
+	phy-mode = "rmii";
+	use-ncsi;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii3_default>;
+};
+
+&mac3 {
+	status = "okay";
+	phy-mode = "rmii";
+	use-ncsi;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+};
+
+&fmc {
+	status = "okay";
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		label = "bios";
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+
+	temperature-sensor@48 {
+		compatible = "ti,tmp75";
+		reg = <0x48>;
+	};
+
+	temperature-sensor@49 {
+		compatible = "ti,tmp75";
+		reg = <0x49>;
+	};
+
+	pca9555_4_20: gpio@20 {
+		compatible = "nxp,pca9555";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	pca9555_4_22: gpio@22 {
+		compatible = "nxp,pca9555";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	pca9555_4_24: gpio@24 {
+		compatible = "nxp,pca9555";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+		/*A0 - A3 0*/	"", "STRAP_BMC_BATTERY_GPIO1", "", "",
+		/*A4 - A7 4*/	"", "", "", "",
+		/*B0 - B7 8*/	"", "", "", "", "", "", "", "";
+	};
+
+	pca9555_4_26: gpio@26 {
+		compatible = "nxp,pca9555";
+		reg = <0x26>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		status = "okay";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel_1: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		channel_2: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		channel_3: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		channel_4: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	pca9555_5_24: gpio@24 {
+		compatible = "nxp,pca9555";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	i2c-mux@70  {
+		compatible = "nxp,pca9546";
+		status = "okay";
+		reg = <0x70 >;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel_5: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			pca9555_5_5_20: gpio@20 {
+				compatible = "nxp,pca9555";
+				reg = <0x20>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				gpio-line-names =
+					"", "", "", "", "", "", "", "",
+					"", "", "SYS_FAN6", "SYS_FAN5",
+					"SYS_FAN4", "SYS_FAN3",
+					"SYS_FAN2", "SYS_FAN1";
+			};
+
+			pca9555_5_5_21: gpio@21 {
+				compatible = "nxp,pca9555";
+				reg = <0x21>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			power-monitor@44 {
+				compatible = "ti,ina219";
+				reg = <0x44>;
+				shunt-resistor = <2>;
+			};
+		};
+
+		channel_6: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		channel_7: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		channel_8: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&i2c6 {
+	status = "okay";
+
+	pca9555_6_27: gpio@27 {
+		compatible = "nxp,pca9555";
+		reg = <0x27>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	pca9555_6_20: gpio@20 {
+		compatible = "nxp,pca9555";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+		/*A0 0*/	"", "", "", "", "", "", "", "",
+		/*B0 8*/	"Drive_NVMe1", "Drive_NVMe2", "", "",
+		/*B4 12*/	"", "", "", "";
+	};
+
+	pca9555_6_21: gpio@21 {
+		compatible = "nxp,pca9555";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+};
+
+&i2c7 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		status = "okay";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		idle-state = <1>;
+
+		channel_9: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			temperature-sensor@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+
+			temperature-sensor@49 {
+				compatible = "ti,tmp75";
+				reg = <0x49>;
+			};
+
+			power-monitor@40 {
+				compatible = "ti,ina219";
+				reg = <0x40>;
+				shunt-resistor = <2>;
+			};
+
+			power-monitor@41 {
+				compatible = "ti,ina219";
+				reg = <0x41>;
+				shunt-resistor = <5>;
+			};
+		};
+
+		channel_10: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		channel_11: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		channel_12: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9546";
+		status = "okay";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		channel_13: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		channel_14: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		channel_15: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		channel_16: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&i2c8 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		status = "okay";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		channel_17: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		channel_18: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			temperature-sensor@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+
+			power-monitor@41 {
+				compatible = "ti,ina219";
+				reg = <0x41>;
+				shunt-resistor = <5>;
+			};
+		};
+
+		channel_19: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		channel_20: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+};
+
+&i2c14 {
+	status = "okay";
+	multi-master;
+
+	eeprom@50 {
+		compatible = "atmel,24c08";
+		reg = <0x50>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c08";
+		reg = <0x51>;
+	};
+};
+
+&sgpiom0 {
+	status = "okay";
+	ngpios = <128>;
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+&sdc {
+	status = "okay";
+};
+
+&lpc_snoop {
+	status = "okay";
+	snoop-ports = <0x80>;
+};
+
+&kcs1 {
+	aspeed,lpc-io-reg = <0xca0>;
+	status = "okay";
+};
+
+&kcs2 {
+	aspeed,lpc-io-reg = <0xca8>;
+	status = "okay";
+};
+
+&kcs3 {
+	aspeed,lpc-io-reg = <0xca2>;
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&uart_routing {
+	status = "okay";
+};
+
+&vhub {
+	status = "okay";
+};
+
+&gpio0 {
+	gpio-line-names =
+	/*A0 0*/	"", "", "", "", "", "", "", "",
+	/*B0 8*/	"", "", "", "", "", "", "PS_PWROK", "",
+	/*C0 16*/	"", "", "", "", "", "", "", "",
+	/*D0 24*/	"", "", "", "", "", "", "", "",
+	/*E0 32*/	"", "", "", "", "", "", "", "",
+	/*F0 40*/	"", "", "", "", "", "", "", "",
+	/*G0 48*/	"", "", "", "", "", "", "", "",
+	/*H0 56*/	"", "", "", "", "", "", "", "",
+	/*I0 64*/	"", "", "", "", "", "", "", "",
+	/*J0 72*/	"", "", "", "", "", "", "", "",
+	/*K0 80*/	"", "", "", "", "", "", "", "",
+	/*L0 88*/	"", "", "", "", "", "", "", "",
+	/*M0 96*/	"", "", "", "", "", "", "", "",
+	/*N0 104*/	"", "", "", "",
+	/*N4 108*/	"POST_COMPLETE", "ESR1_GPIO_AST_SPISEL", "", "",
+	/*O0 112*/	"", "", "", "", "", "", "", "",
+	/*P0 120*/	"ID_BUTTON", "ID_OUT", "POWER_BUTTON", "POWER_OUT",
+	/*P4 124*/	"RESET_BUTTON", "RESET_OUT", "", "HEARTBEAT",
+	/*Q0 128*/	"", "", "", "", "", "", "", "",
+	/*R0 136*/	"", "", "", "", "", "", "", "",
+	/*S0 144*/	"", "", "", "", "", "", "", "",
+	/*T0 152*/	"", "", "", "", "", "", "", "",
+	/*U0 160*/	"", "", "", "", "", "", "", "",
+	/*V0 168*/	"", "", "", "", "", "", "", "",
+	/*W0 176*/	"", "", "", "", "", "", "", "",
+	/*X0 184*/	"", "", "", "", "", "", "", "",
+	/*Y0 192*/	"", "", "", "", "", "", "", "",
+	/*Z0 200*/	"", "", "", "", "", "", "", "";
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-bytedance-g220a.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-bytedance-g220a.dts
index 0d1fb5ccfd36..54a5509b04f1 100644
--- a/arch/arm/boot/dts/aspeed-bmc-bytedance-g220a.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-bytedance-g220a.dts
@@ -100,7 +100,7 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		burn-in-signal {
+		event-burn-in-signal {
 			label = "burn-in";
 			gpios = <&gpio ASPEED_GPIO(R, 5) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(R, 5)>;
@@ -111,139 +111,139 @@
 		compatible = "gpio-keys-polled";
 		poll-interval = <1000>;
 
-		rear-riser1-presence {
+		event-rear-riser1-presence {
 			label = "rear-riser1-presence";
 			gpios = <&pca0 1 GPIO_ACTIVE_LOW>;
 			linux,code = <1>;
 		};
 
-		alrt-pvddq-cpu0 {
+		event-alrt-pvddq-cpu0 {
 			label = "alrt-pvddq-cpu0";
 			gpios = <&pca0 8 GPIO_ACTIVE_LOW>;
 			linux,code = <2>;
 		};
 
-		rear-riser0-presence {
+		event-rear-riser0-presence {
 			label = "rear-riser0-presence";
 			gpios = <&pca0 9 GPIO_ACTIVE_LOW>;
 			linux,code = <3>;
 		};
 
-		fault-pvddq-cpu0 {
+		event-fault-pvddq-cpu0 {
 			label = "fault-pvddq-cpu0";
 			gpios = <&pca0 10 GPIO_ACTIVE_LOW>;
 			linux,code = <4>;
 		};
 
-		alrt-pvddq-cpu1 {
+		event-alrt-pvddq-cpu1 {
 			label = "alrt-pvddq-cpu1";
 			gpios = <&pca0 11 GPIO_ACTIVE_LOW>;
 			linux,code = <5>;
 		};
 
-		fault-pvddq-cpu1 {
+		event-fault-pvddq-cpu1 {
 			label = "alrt-pvddq-cpu1";
 			gpios = <&pca0 12 GPIO_ACTIVE_LOW>;
 			linux,code = <6>;
 		};
 
-		fault-pvccin-cpu1 {
+		event-fault-pvccin-cpu1 {
 			label = "fault-pvccin-cpuq";
 			gpios = <&pca0 13 GPIO_ACTIVE_LOW>;
 			linux,code = <7>;
 		};
 
-		bmc-rom0-wp {
+		event-bmc-rom0-wp {
 			label = "bmc-rom0-wp";
 			gpios = <&pca1 0 GPIO_ACTIVE_LOW>;
 			linux,code = <8>;
 		};
 
-		bmc-rom1-wp {
+		event-bmc-rom1-wp {
 			label = "bmc-rom1-wp";
 			gpios = <&pca1 1 GPIO_ACTIVE_LOW>;
 			linux,code = <9>;
 		};
 
-		fan0-presence {
+		event-fan0-presence {
 			label = "fan0-presence";
 			gpios = <&pca1 2 GPIO_ACTIVE_LOW>;
 			linux,code = <10>;
 		};
 
-		fan1-presence {
+		event-fan1-presence {
 			label = "fan1-presence";
 			gpios = <&pca1 3 GPIO_ACTIVE_LOW>;
 			linux,code = <11>;
 		};
 
-		fan2-presence {
+		event-fan2-presence {
 			label = "fan2-presence";
 			gpios = <&pca1 4 GPIO_ACTIVE_LOW>;
 			linux,code = <12>;
 		};
 
-		fan3-presence {
+		event-fan3-presence {
 			label = "fan3-presence";
 			gpios = <&pca1 5 GPIO_ACTIVE_LOW>;
 			linux,code = <13>;
 		};
 
-		fan4-presence {
+		event-fan4-presence {
 			label = "fan4-presence";
 			gpios = <&pca1 6 GPIO_ACTIVE_LOW>;
 			linux,code = <14>;
 		};
 
-		fan5-presence {
+		event-fan5-presence {
 			label = "fan5-presence";
 			gpios = <&pca1 7 GPIO_ACTIVE_LOW>;
 			linux,code = <15>;
 		};
 
-		front-bp1-presence {
+		event-front-bp1-presence {
 			label = "front-bp1-presence";
 			gpios = <&pca1 8 GPIO_ACTIVE_LOW>;
 			linux,code = <16>;
 		};
 
-		rear-bp-presence {
+		event-rear-bp-presence {
 			label = "rear-bp-presence";
 			gpios = <&pca1 9 GPIO_ACTIVE_LOW>;
 			linux,code = <17>;
 		};
 
-		fault-pvccin-cpu0 {
+		event-fault-pvccin-cpu0 {
 			label = "fault-pvccin-cpu0";
 			gpios = <&pca1 10 GPIO_ACTIVE_LOW>;
 			linux,code = <18>;
 		};
 
-		alrt-p1v05-pvcc {
+		event-alrt-p1v05-pvcc {
 			label = "alrt-p1v05-pvcc1";
 			gpios = <&pca1 11 GPIO_ACTIVE_LOW>;
 			linux,code = <19>;
 		};
 
-		fault-p1v05-pvccio {
+		event-fault-p1v05-pvccio {
 			label = "alrt-p1v05-pvcc1";
 			gpios = <&pca1 12 GPIO_ACTIVE_LOW>;
 			linux,code = <20>;
 		};
 
-		alrt-p1v8-pvccio {
+		event-alrt-p1v8-pvccio {
 			label = "alrt-p1v8-pvccio";
 			gpios = <&pca1 13 GPIO_ACTIVE_LOW>;
 			linux,code = <21>;
 		};
 
-		fault-p1v8-pvccio {
+		event-fault-p1v8-pvccio {
 			label = "fault-p1v8-pvccio";
 			gpios = <&pca1 14 GPIO_ACTIVE_LOW>;
 			linux,code = <22>;
 		};
 
-		front-bp0-presence {
+		event-front-bp0-presence {
 			label = "front-bp0-presence";
 			gpios = <&pca1 15 GPIO_ACTIVE_LOW>;
 			linux,code = <23>;
@@ -424,7 +424,7 @@
 
 &i2c3 {
 	status = "okay";
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		reg = <0x70>;
 		#address-cells = <1>;
@@ -471,7 +471,7 @@
 
 &i2c6 {
 	status = "okay";
-	i2c-switch@72 {
+	i2c-mux@72 {
 		compatible = "nxp,pca9548";
 		reg = <0x72>;
 		#address-cells = <1>;
@@ -524,7 +524,7 @@
 		};
 	};
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		reg = <0x70>;
 		#address-cells = <1>;
@@ -533,7 +533,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0>;
-			i2c-switch@71 {
+			i2c-mux@71 {
 				compatible = "nxp,pca9546";
 				reg = <0x71>;
 				#address-cells = <1>;
@@ -569,7 +569,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <1>;
-			i2c-switch@71 {
+			i2c-mux@71 {
 				compatible = "nxp,pca9546";
 				reg = <0x71>;
 				#address-cells = <1>;
@@ -605,7 +605,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <2>;
-			i2c-switch@71 {
+			i2c-mux@71 {
 				compatible = "nxp,pca9546";
 				reg = <0x71>;
 				#address-cells = <1>;
@@ -640,7 +640,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <3>;
-			i2c-switch@71 {
+			i2c-mux@71 {
 				compatible = "nxp,pca9546";
 				reg = <0x71>;
 				#address-cells = <1>;
@@ -808,7 +808,7 @@
 
 &i2c10 {
 	status = "okay";
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		reg = <0x70>;
 		#address-cells = <1>;
@@ -838,7 +838,7 @@
 		};
 	};
 
-	i2c-switch@71 {
+	i2c-mux@71 {
 		compatible = "nxp,pca9546";
 		reg = <0x71>;
 		#address-cells = <1>;
@@ -915,14 +915,14 @@
 };
 
 &gpio {
-	pin_gpio_i3 {
+	pin-gpio-i3-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(I, 3) GPIO_ACTIVE_HIGH>;
 		output-low;
 		line-name = "NCSI_BMC_R_SEL";
 	};
 
-	pin_gpio_b6 {
+	pin-gpio-b6-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(B, 6) GPIO_ACTIVE_HIGH>;
 		output-low;
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-delta-ahe50dc.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-delta-ahe50dc.dts
new file mode 100644
index 000000000000..cce8d0416dc8
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-delta-ahe50dc.dts
@@ -0,0 +1,418 @@
+// SPDX-License-Identifier: GPL-2.0+
+/dts-v1/;
+
+#include "aspeed-g4.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+#define EFUSE_OUTPUT(n)					\
+	efuse##n {					\
+		compatible = "regulator-output";	\
+		vout-supply = <&efuse##n>;		\
+	}
+
+#define __stringify(x) #x
+
+#define EFUSE(hexaddr, num)							\
+	efuse@##hexaddr {							\
+		compatible = "ti,lm25066";					\
+		reg = <0x##hexaddr>;						\
+		shunt-resistor-micro-ohms = <675>;				\
+		regulators {							\
+			efuse##num: vout {					\
+				regulator-name = __stringify(efuse##num##-reg);	\
+			};							\
+		};								\
+	}
+
+/{
+	model = "Delta Power AHE-50DC";
+	compatible = "delta,ahe50dc-bmc", "aspeed,ast2400";
+
+	aliases {
+		serial4 = &uart5;
+
+		/*
+		 * pca9541-arbitrated logical i2c buses are numbered as the
+		 * corresponding physical bus plus 20
+		 */
+		i2c20 = &i2carb0;
+		i2c21 = &i2carb1;
+		i2c22 = &i2carb2;
+		i2c23 = &i2carb3;
+		i2c24 = &i2carb4;
+		i2c26 = &i2carb6;
+		i2c27 = &i2carb7;
+		i2c28 = &i2carb8;
+		i2c32 = &i2carb12;
+	};
+
+	chosen {
+		stdout-path = &uart3;
+		bootargs = "console=ttyS2,115200n8 earlycon";
+	};
+
+	memory@40000000 {
+		reg = <0x40000000 0x10000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		heartbeat {
+			gpios = <&gpio ASPEED_GPIO(P, 0) GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		panic {
+			gpios = <&gpio ASPEED_GPIO(P, 2) GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "panic";
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>, <&adc 4>,
+			<&adc 5>, <&adc 6>, <&adc 7>, <&adc 8>, <&adc 9>;
+	};
+
+	EFUSE_OUTPUT(01);
+	EFUSE_OUTPUT(02);
+	EFUSE_OUTPUT(03);
+	EFUSE_OUTPUT(04);
+	EFUSE_OUTPUT(05);
+	EFUSE_OUTPUT(06);
+	EFUSE_OUTPUT(07);
+	EFUSE_OUTPUT(08);
+	EFUSE_OUTPUT(09);
+	EFUSE_OUTPUT(10);
+	EFUSE_OUTPUT(11);
+	EFUSE_OUTPUT(12);
+	EFUSE_OUTPUT(13);
+	EFUSE_OUTPUT(14);
+	EFUSE_OUTPUT(15);
+	EFUSE_OUTPUT(16);
+	EFUSE_OUTPUT(17);
+	EFUSE_OUTPUT(18);
+	EFUSE_OUTPUT(19);
+	EFUSE_OUTPUT(20);
+	EFUSE_OUTPUT(21);
+	EFUSE_OUTPUT(22);
+	EFUSE_OUTPUT(23);
+	EFUSE_OUTPUT(24);
+	EFUSE_OUTPUT(25);
+	EFUSE_OUTPUT(26);
+	EFUSE_OUTPUT(27);
+	EFUSE_OUTPUT(28);
+	EFUSE_OUTPUT(29);
+	EFUSE_OUTPUT(30);
+	EFUSE_OUTPUT(31);
+	EFUSE_OUTPUT(32);
+	EFUSE_OUTPUT(33);
+	EFUSE_OUTPUT(34);
+	EFUSE_OUTPUT(35);
+	EFUSE_OUTPUT(36);
+	EFUSE_OUTPUT(37);
+	EFUSE_OUTPUT(38);
+	EFUSE_OUTPUT(39);
+	EFUSE_OUTPUT(40);
+	EFUSE_OUTPUT(41);
+	EFUSE_OUTPUT(42);
+	EFUSE_OUTPUT(43);
+	EFUSE_OUTPUT(44);
+	EFUSE_OUTPUT(45);
+	EFUSE_OUTPUT(46);
+	EFUSE_OUTPUT(47);
+	EFUSE_OUTPUT(48);
+	EFUSE_OUTPUT(49);
+	EFUSE_OUTPUT(50);
+
+};
+
+&fmc {
+	status = "okay";
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "flash0";
+		spi-max-frequency = <50000000>; // 50 MHz
+#include "openbmc-flash-layout.dtsi"
+	};
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&mac1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
+};
+
+&i2c0 {
+	status = "okay";
+	bus-frequency = <200000>;
+
+	pca9541@79 {
+		compatible = "nxp,pca9541";
+		reg = <0x79>;
+
+		i2carb0: i2c-arb {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* lm25066 efuses @ 10-17, 40-47, 50-57 */
+			EFUSE(10, 03);
+			EFUSE(11, 04);
+			EFUSE(12, 01);
+			EFUSE(13, 02);
+			EFUSE(14, 13);
+			EFUSE(15, 14);
+			EFUSE(16, 15);
+			EFUSE(17, 16);
+			EFUSE(40, 12);
+			EFUSE(41, 11);
+			EFUSE(42, 10);
+			EFUSE(43, 09);
+			EFUSE(44, 08);
+			EFUSE(45, 07);
+			EFUSE(46, 05);
+			EFUSE(47, 06);
+			EFUSE(50, 17);
+			EFUSE(51, 18);
+			EFUSE(52, 20);
+			EFUSE(53, 19);
+			EFUSE(54, 22);
+			EFUSE(55, 21);
+			EFUSE(56, 24);
+			EFUSE(57, 23);
+		};
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	bus-frequency = <200000>;
+
+	pca9541@72 {
+		compatible = "nxp,pca9541";
+		reg = <0x72>;
+
+		i2carb1: i2c-arb {
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&i2c2 {
+	status = "okay";
+	bus-frequency = <200000>;
+
+	pca9541@73 {
+		compatible = "nxp,pca9541";
+		reg = <0x73>;
+
+		i2carb2: i2c-arb {
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&i2c3 {
+	status = "okay";
+	bus-frequency = <200000>;
+
+	pca9541@74 {
+		compatible = "nxp,pca9541";
+		reg = <0x74>;
+
+		i2carb3: i2c-arb {
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&i2c4 {
+	status = "okay";
+	bus-frequency = <200000>;
+
+	pca9541@7a {
+		compatible = "nxp,pca9541";
+		reg = <0x7a>;
+
+		i2carb4: i2c-arb {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			gpio@20 {
+				compatible = "nxp,pca9534";
+				reg = <0x20>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			/* lm25066 efuses @ 10-17, 40-47, 50-57, 59, 5a */
+			EFUSE(10, 27);
+			EFUSE(11, 28);
+			EFUSE(12, 25);
+			EFUSE(13, 26);
+			EFUSE(14, 37);
+			EFUSE(15, 38);
+			EFUSE(16, 39);
+			EFUSE(17, 40);
+			EFUSE(40, 36);
+			EFUSE(41, 35);
+			EFUSE(42, 34);
+			EFUSE(43, 33);
+			EFUSE(44, 32);
+			EFUSE(45, 31);
+			EFUSE(46, 29);
+			EFUSE(47, 30);
+			EFUSE(50, 41);
+			EFUSE(51, 42);
+			EFUSE(52, 44);
+			EFUSE(53, 43);
+			EFUSE(54, 46);
+			EFUSE(55, 45);
+			EFUSE(56, 48);
+			EFUSE(57, 47);
+			EFUSE(59, 49);
+			EFUSE(5a, 50);
+		};
+	};
+};
+
+&i2c6 {
+	status = "okay";
+	bus-frequency = <200000>;
+
+	pca9541@75 {
+		compatible = "nxp,pca9541";
+		reg = <0x75>;
+
+		i2carb6: i2c-arb {
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&i2c7 {
+	status = "okay";
+	bus-frequency = <200000>;
+
+	pca9541@76 {
+		compatible = "nxp,pca9541";
+		reg = <0x76>;
+
+		i2carb7: i2c-arb {
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&i2c8 {
+	status = "okay";
+	bus-frequency = <200000>;
+
+	pca9541@7c {
+		compatible = "nxp,pca9541";
+		reg = <0x7c>;
+
+		i2carb8: i2c-arb {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fancontrol@30 {
+				compatible = "delta,ahe50dc-fan";
+				reg = <0x30>;
+			};
+
+			/* Baseboard FRU eeprom */
+			eeprom@50 {
+				compatible = "atmel,24c02";
+				reg = <0x50>;
+			};
+		};
+	};
+};
+
+&i2c12 {
+	status = "okay";
+	bus-frequency = <200000>;
+
+	pca9541@71 {
+		compatible = "nxp,pca9541";
+		reg = <0x71>;
+
+		i2carb12: i2c-arb {
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names =
+		/*  A */ "", "", "", "", "", "", "", "",
+		/*  B */ "", "", "", "", "", "", "", "",
+		/*  C */ "RESET_PEER_N", "HEARTBEAT_OUT", "", "", "", "", "", "",
+		/*  D */ "", "", "", "", "", "", "", "",
+		/*  E */ "DOOM_N", "", "", "", "", "LED_PWR_BLUE", "", "",
+		/*  F */ "", "", "", "", "", "", "", "",
+		/*  G */ "", "", "", "", "", "", "", "",
+		/*  H */ "", "", "", "", "", "", "", "",
+		/*  I */ "", "", "", "", "", "", "", "",
+		/*  J */ "", "", "BMC_ID", "", "", "", "", "",
+		/*  K */ "", "", "", "", "", "", "", "",
+		/*  L */ "", "", "", "", "", "", "", "",
+		/*  M */ "", "", "", "", "", "", "", "",
+		/*  N */ "", "", "", "", "", "", "", "",
+		/*  O */ "", "", "", "", "", "", "", "",
+		/*  P */ "LED_GREEN", "", "LED_RED", "", "", "", "", "",
+		/*  Q */ "", "", "", "", "", "", "", "",
+		/*  R */ "", "", "", "", "", "", "", "",
+		/*  S */ "", "", "", "", "", "", "", "",
+		/*  T */ "", "", "", "", "", "", "", "",
+		/*  U */ "", "", "", "", "", "", "", "",
+		/*  V */ "", "", "", "", "", "", "", "",
+		/*  W */ "", "", "", "", "", "", "", "",
+		/*  X */ "", "", "", "", "", "", "", "",
+		/*  Y */ "HEARTBEAT_IN", "BOARDREV0", "BOARDREV1", "",
+		/*  Z */ "", "", "", "", "", "", "", "",
+		/* AA */ "", "", "", "", "", "", "", "",
+		/* AB */ "", "", "", "";
+
+	/*
+	 * I don't rightly know what this GPIO really *is*, but setting it to
+	 * zero causes the fans to run at full speed, after which setting it
+	 * back to one causes a power output glitch, so install a hog to keep
+	 * it at one as a failsafe to ensure nothing accidentally touches it.
+	 */
+	doom-guardrail-hog {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(E, 0) GPIO_ACTIVE_LOW>;
+		output-low;
+	};
+};
+
+&adc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default
+		&pinctrl_adc1_default
+		&pinctrl_adc2_default
+		&pinctrl_adc3_default
+		&pinctrl_adc4_default
+		&pinctrl_adc5_default
+		&pinctrl_adc6_default
+		&pinctrl_adc7_default
+		&pinctrl_adc8_default
+		&pinctrl_adc9_default>;
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-bletchley.dts
index eaf1bc261ee3..24969c82d05e 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-bletchley.dts
@@ -7,6 +7,7 @@
 #include <dt-bindings/usb/pd.h>
 #include <dt-bindings/leds/leds-pca955x.h>
 #include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/i2c/i2c.h>
 
 / {
 	model = "Facebook Bletchley BMC";
@@ -44,42 +45,18 @@
 		num-chipselects = <1>;
 		cs-gpios = <&gpio0 ASPEED_GPIO(Z, 0) GPIO_ACTIVE_LOW>;
 
-		tpmdev@0 {
-			compatible = "tcg,tpm_tis-spi";
+		tpm@0 {
+			compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
 			spi-max-frequency = <33000000>;
 			reg = <0>;
 		};
 	};
 
-	spi2_gpio: spi2-gpio {
-		compatible = "spi-gpio";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		gpio-sck = <&gpio0 ASPEED_GPIO(X, 3) GPIO_ACTIVE_HIGH>;
-		gpio-mosi = <&gpio0 ASPEED_GPIO(X, 4) GPIO_ACTIVE_HIGH>;
-		gpio-miso = <&gpio0 ASPEED_GPIO(X, 5) GPIO_ACTIVE_HIGH>;
-		num-chipselects = <1>;
-		cs-gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>;
-
-		flash@0 {
-			reg = <0>;
-			compatible = "jedec,spi-nor";
-			m25p,fast-read;
-			label = "pnor";
-			spi-max-frequency = <100000000>;
-		};
-	};
-
-	switchphy: ethernet-phy@0 {
-		// Fixed link
-	};
-
 	front_gpio_leds {
 		compatible = "gpio-leds";
 		sys_log_id {
 			default-state = "off";
-			gpios = <&front_leds 0 GPIO_ACTIVE_HIGH>;
+			gpios = <&front_leds 0 GPIO_ACTIVE_LOW>;
 		};
 	};
 
@@ -210,12 +187,100 @@
 			gpios = <&sled6_leds 1 GPIO_ACTIVE_LOW>;
 		};
 	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		presence-sled1 {
+			label = "presence-sled1";
+			gpios = <&gpio0 ASPEED_GPIO(H, 2) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(H, 2)>;
+		};
+		presence-sled2 {
+			label = "presence-sled2";
+			gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(H, 3)>;
+		};
+		presence-sled3 {
+			label = "presence-sled3";
+			gpios = <&gpio0 ASPEED_GPIO(H, 4) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(H, 4)>;
+		};
+		presence-sled4 {
+			label = "presence-sled4";
+			gpios = <&gpio0 ASPEED_GPIO(H, 5) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(H, 5)>;
+		};
+		presence-sled5 {
+			label = "presence-sled5";
+			gpios = <&gpio0 ASPEED_GPIO(H, 6) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(H, 6)>;
+		};
+		presence-sled6 {
+			label = "presence-sled6";
+			gpios = <&gpio0 ASPEED_GPIO(H, 7) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(H, 7)>;
+		};
+	};
+
+	vbus_sled1: vbus_sled1 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbus_sled1";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&sled1_ioexp 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vbus_sled2: vbus_sled2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbus_sled2";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&sled2_ioexp 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vbus_sled3: vbus_sled3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbus_sled3";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&sled3_ioexp 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vbus_sled4: vbus_sled4 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbus_sled4";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&sled4_ioexp 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vbus_sled5: vbus_sled5 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbus_sled5";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&sled5_ioexp 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vbus_sled6: vbus_sled6 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbus_sled6";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&sled6_ioexp 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 };
 
 &mac2 {
 	status = "okay";
 	phy-mode = "rgmii";
-	phy-handle = <&switchphy>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_rgmii3_default>;
 
@@ -237,7 +302,20 @@
 	flash@1 {
 		status = "okay";
 		m25p,fast-read;
-		label = "flash1";
+		label = "alt-bmc";
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&spi2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi2_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "pnor";
 		spi-max-frequency = <50000000>;
 	};
 };
@@ -260,6 +338,17 @@
 		reg = <0x4f>;
 	};
 
+	sled1_ioexp41: pca9536@41 {
+		compatible = "nxp,pca9536";
+		reg = <0x41>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"SLED1_SWD_MUX", "SLED1_XRES_SWD_N",
+		"SLED1_CLKREQ_N", "SLED1_PCIE_PWR_EN";
+	};
+
 	sled1_ioexp: pca9539@76 {
 		compatible = "nxp,pca9539";
 		reg = <0x76>;
@@ -297,19 +386,27 @@
 		compatible = "fcs,fusb302";
 		reg = <0x22>;
 
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(B, 0) IRQ_TYPE_LEVEL_LOW>;
+		vbus-supply = <&vbus_sled1>;
+
 		connector {
 			compatible = "usb-c-connector";
 			label = "USB-C";
+			pd-revision = /bits/ 8 <0x2 0x0 0x1 0x20>;
 			power-role = "dual";
 			try-power-role = "sink";
 			data-role = "dual";
 			source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
-			sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
-					PDO_VAR(3000, 12000, 3000)
-					PDO_PPS_APDO(3000, 11000, 3000)>;
+			sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
 			op-sink-microwatt = <10000000>;
 		};
 	};
+
+	eeprom@54 {
+		compatible = "atmel,24c64";
+		reg = <0x54>;
+	};
 };
 
 &i2c1 {
@@ -330,6 +427,17 @@
 		reg = <0x4f>;
 	};
 
+	sled2_ioexp41: pca9536@41 {
+		compatible = "nxp,pca9536";
+		reg = <0x41>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"SLED2_SWD_MUX", "SLED2_XRES_SWD_N",
+		"SLED2_CLKREQ_N", "SLED2_PCIE_PWR_EN";
+	};
+
 	sled2_ioexp: pca9539@76 {
 		compatible = "nxp,pca9539";
 		reg = <0x76>;
@@ -367,19 +475,27 @@
 		compatible = "fcs,fusb302";
 		reg = <0x22>;
 
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(B, 1) IRQ_TYPE_LEVEL_LOW>;
+		vbus-supply = <&vbus_sled2>;
+
 		connector {
 			compatible = "usb-c-connector";
 			label = "USB-C";
+			pd-revision = /bits/ 8 <0x2 0x0 0x1 0x20>;
 			power-role = "dual";
 			try-power-role = "sink";
 			data-role = "dual";
 			source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
-			sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
-					PDO_VAR(3000, 12000, 3000)
-					PDO_PPS_APDO(3000, 11000, 3000)>;
+			sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
 			op-sink-microwatt = <10000000>;
 		};
 	};
+
+	eeprom@54 {
+		compatible = "atmel,24c64";
+		reg = <0x54>;
+	};
 };
 
 &i2c2 {
@@ -400,6 +516,17 @@
 		reg = <0x4f>;
 	};
 
+	sled3_ioexp41: pca9536@41 {
+		compatible = "nxp,pca9536";
+		reg = <0x41>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"SLED3_SWD_MUX", "SLED3_XRES_SWD_N",
+		"SLED3_CLKREQ_N", "SLED3_PCIE_PWR_EN";
+	};
+
 	sled3_ioexp: pca9539@76 {
 		compatible = "nxp,pca9539";
 		reg = <0x76>;
@@ -437,19 +564,27 @@
 		compatible = "fcs,fusb302";
 		reg = <0x22>;
 
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(B, 7) IRQ_TYPE_LEVEL_LOW>;
+		vbus-supply = <&vbus_sled3>;
+
 		connector {
 			compatible = "usb-c-connector";
 			label = "USB-C";
+			pd-revision = /bits/ 8 <0x2 0x0 0x1 0x20>;
 			power-role = "dual";
 			try-power-role = "sink";
 			data-role = "dual";
 			source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
-			sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
-					PDO_VAR(3000, 12000, 3000)
-					PDO_PPS_APDO(3000, 11000, 3000)>;
+			sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
 			op-sink-microwatt = <10000000>;
 		};
 	};
+
+	eeprom@54 {
+		compatible = "atmel,24c64";
+		reg = <0x54>;
+	};
 };
 
 &i2c3 {
@@ -470,6 +605,17 @@
 		reg = <0x4f>;
 	};
 
+	sled4_ioexp41: pca9536@41 {
+		compatible = "nxp,pca9536";
+		reg = <0x41>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"SLED4_SWD_MUX", "SLED4_XRES_SWD_N",
+		"SLED4_CLKREQ_N", "SLED4_PCIE_PWR_EN";
+	};
+
 	sled4_ioexp: pca9539@76 {
 		compatible = "nxp,pca9539";
 		reg = <0x76>;
@@ -507,19 +653,27 @@
 		compatible = "fcs,fusb302";
 		reg = <0x22>;
 
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(S, 7) IRQ_TYPE_LEVEL_LOW>;
+		vbus-supply = <&vbus_sled4>;
+
 		connector {
 			compatible = "usb-c-connector";
 			label = "USB-C";
+			pd-revision = /bits/ 8 <0x2 0x0 0x1 0x20>;
 			power-role = "dual";
 			try-power-role = "sink";
 			data-role = "dual";
 			source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
-			sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
-					PDO_VAR(3000, 12000, 3000)
-					PDO_PPS_APDO(3000, 11000, 3000)>;
+			sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
 			op-sink-microwatt = <10000000>;
 		};
 	};
+
+	eeprom@54 {
+		compatible = "atmel,24c64";
+		reg = <0x54>;
+	};
 };
 
 &i2c4 {
@@ -540,6 +694,17 @@
 		reg = <0x4f>;
 	};
 
+	sled5_ioexp41: pca9536@41 {
+		compatible = "nxp,pca9536";
+		reg = <0x41>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"SLED5_SWD_MUX", "SLED5_XRES_SWD_N",
+		"SLED5_CLKREQ_N", "SLED5_PCIE_PWR_EN";
+	};
+
 	sled5_ioexp: pca9539@76 {
 		compatible = "nxp,pca9539";
 		reg = <0x76>;
@@ -577,19 +742,27 @@
 		compatible = "fcs,fusb302";
 		reg = <0x22>;
 
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(Y, 3) IRQ_TYPE_LEVEL_LOW>;
+		vbus-supply = <&vbus_sled5>;
+
 		connector {
 			compatible = "usb-c-connector";
 			label = "USB-C";
+			pd-revision = /bits/ 8 <0x2 0x0 0x1 0x20>;
 			power-role = "dual";
 			try-power-role = "sink";
 			data-role = "dual";
 			source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
-			sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
-					PDO_VAR(3000, 12000, 3000)
-					PDO_PPS_APDO(3000, 11000, 3000)>;
+			sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
 			op-sink-microwatt = <10000000>;
 		};
 	};
+
+	eeprom@54 {
+		compatible = "atmel,24c64";
+		reg = <0x54>;
+	};
 };
 
 &i2c5 {
@@ -610,6 +783,17 @@
 		reg = <0x4f>;
 	};
 
+	sled6_ioexp41: pca9536@41 {
+		compatible = "nxp,pca9536";
+		reg = <0x41>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"SLED6_SWD_MUX", "SLED6_XRES_SWD_N",
+		"SLED6_CLKREQ_N", "SLED6_PCIE_PWR_EN";
+	};
+
 	sled6_ioexp: pca9539@76 {
 		compatible = "nxp,pca9539";
 		reg = <0x76>;
@@ -647,19 +831,27 @@
 		compatible = "fcs,fusb302";
 		reg = <0x22>;
 
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(I, 7) IRQ_TYPE_LEVEL_LOW>;
+		vbus-supply = <&vbus_sled6>;
+
 		connector {
 			compatible = "usb-c-connector";
 			label = "USB-C";
+			pd-revision = /bits/ 8 <0x2 0x0 0x1 0x20>;
 			power-role = "dual";
 			try-power-role = "sink";
 			data-role = "dual";
 			source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
-			sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
-					PDO_VAR(3000, 12000, 3000)
-					PDO_PPS_APDO(3000, 11000, 3000)>;
+			sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
 			op-sink-microwatt = <10000000>;
 		};
 	};
+
+	eeprom@54 {
+		compatible = "atmel,24c64";
+		reg = <0x54>;
+	};
 };
 
 &i2c6 {
@@ -703,11 +895,6 @@
 		reg = <0x4f>;
 	};
 
-	hdc1080@40 {
-		compatible = "ti,hdc1080";
-		reg = <0x40>;
-	};
-
 	front_leds: pca9552@67 {
 		compatible = "nxp,pca9552";
 		reg = <0x67>;
@@ -732,6 +919,8 @@
 		compatible = "adi,adm1278";
 		reg = <0x11>;
 		shunt-resistor-micro-ohms = <300>;
+		adi,volt-curr-sample-average = <128>;
+		adi,power-sample-average = <128>;
 	};
 
 	tmp421@4c {
@@ -766,48 +955,70 @@
 	multi-master;
 	aspeed,hw-timeout-ms = <1000>;
 	status = "okay";
+
+	//USB Debug Connector
+	ipmb13@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
 };
 
 &gpio0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpiov2_unbiased_default>;
+
 	gpio-line-names =
 	/*A0-A7*/	"","","","","","","","",
-	/*B0-B7*/	"","","SEL_SPI2_MUX","SPI2_MUX1",
-			"SPI2_MUX2","SPI2_MUX3","","",
+	/*B0-B7*/	"FUSB302_SLED1_INT_N","FUSB302_SLED2_INT_N",
+			"SEL_SPI2_MUX","SPI2_MUX1",
+			"SPI2_MUX2","SPI2_MUX3",
+			"","FUSB302_SLED3_INT_N",
 	/*C0-C7*/	"","","","","","","","",
 	/*D0-D7*/	"","","","","","","","",
 	/*E0-E7*/	"","","","","","","","",
-	/*F0-F7*/	"","","","","","","","",
-	/*G0-G7*/	"BSM_FRU_WP","SWITCH_FRU_MUX","","",
+	/*F0-F7*/	"BMC_SLED1_STCK","BMC_SLED2_STCK",
+			"BMC_SLED3_STCK","BMC_SLED4_STCK",
+			"BMC_SLED5_STCK","BMC_SLED6_STCK",
+			"","",
+	/*G0-G7*/	"BSM_FRU_WP","SWITCH_FRU_MUX","","FM_SOL_UART_CH_SEL",
 			"PWRGD_P1V05_VDDCORE","PWRGD_P1V5_VDD","","",
 	/*H0-H7*/	"presence-riser1","presence-riser2",
 			"presence-sled1","presence-sled2",
 			"presence-sled3","presence-sled4",
 			"presence-sled5","presence-sled6",
-	/*I0-I7*/	"REV_ID0","","REV_ID1","REV_ID2",
-			"","BSM_FLASH_WP_STATUS","BMC_TPM_PRES","",
+	/*I0-I7*/	"REV_ID0","",
+			"REV_ID1","REV_ID2",
+			"","BSM_FLASH_WP_STATUS",
+			"BMC_TPM_PRES_N","FUSB302_SLED6_INT_N",
 	/*J0-J7*/	"","","","","","","","",
 	/*K0-K7*/	"","","","","","","","",
 	/*L0-L7*/	"","","","","","BMC_RTC_INT","","",
-	/*M0-M7*/	"ALERT_SLED1","ALERT_SLED2",
-			"ALERT_SLED3","ALERT_SLED4",
-			"ALERT_SLED5","ALERT_SLED6",
-			"P12V_AUX_ALERT1","",
-	/*N0-N7*/	"","","","","","","","",
+	/*M0-M7*/	"ALERT_SLED1_N","ALERT_SLED2_N",
+			"ALERT_SLED3_N","ALERT_SLED4_N",
+			"ALERT_SLED5_N","ALERT_SLED6_N",
+			"","USB_DEBUG_PWR_BTN_N",
+	/*N0-N7*/	"LED_POSTCODE_0","LED_POSTCODE_1",
+			"LED_POSTCODE_2","LED_POSTCODE_3",
+			"LED_POSTCODE_4","LED_POSTCODE_5",
+			"LED_POSTCODE_6","LED_POSTCODE_7",
 	/*O0-O7*/	"","","","",
 			"","BOARD_ID0","BOARD_ID1","BOARD_ID2",
 	/*P0-P7*/	"","","","","","","","BMC_HEARTBEAT",
 	/*Q0-Q7*/	"","","","","","","","",
 	/*R0-R7*/	"","","","","","","","",
 	/*S0-S7*/	"","","","BAT_DETECT",
-			"BMC_BT_WP0","BMC_BT_WP1","","",
+			"BMC_BT_WP0_N","BMC_BT_WP1_N","","FUSB302_SLED4_INT_N",
 	/*T0-T7*/	"","","","","","","","",
 	/*U0-U7*/	"","","","","","","","",
-	/*V0-V7*/	"PWRGD_CNS_PSU","RST_BMC_MVL","","PSU_PRSNT",
+	/*V0-V7*/	"PWRGD_CNS_PSU","RST_BMC_MVL_N",
+			"P12V_AUX_ALERT1_N","PSU_PRSNT",
 			"USB2_SEL0_A","USB2_SEL1_A",
 			"USB2_SEL0_B","USB2_SEL1_B",
-	/*W0-W7*/	"RST_FRONT_IOEXP","","","","","","","",
+	/*W0-W7*/	"RST_FRONT_IOEXP_N","","","","","","","",
 	/*X0-X7*/	"","","","","","","","",
-	/*Y0-Y7*/	"BMC_SELF_HW_RST","BSM_PRSNT","BSM_FLASH_LATCH","",
+	/*Y0-Y7*/	"BMC_SELF_HW_RST","BSM_PRSNT_N",
+			"BSM_FLASH_LATCH_N","FUSB302_SLED5_INT_N",
 			"","","","",
 	/*Z0-Z7*/	"","","","","","","","";
 };
@@ -834,7 +1045,46 @@
 		&pinctrl_adc14_default &pinctrl_adc15_default>;
 };
 
+&mdio0 {
+	status = "okay";
+	/* TODO: Add Marvell 88E6191X */
+};
+
 &mdio3 {
 	status = "okay";
 	/* TODO: Add Marvell 88X3310 */
 };
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&emmc {
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl_gpiov2_unbiased_default: gpiov2 {
+		pins = "AD14";
+		bias-disable;
+	};
+};
+
+&wdt1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst1_default>;
+	aspeed,reset-type = "soc";
+	aspeed,external-signal;
+	aspeed,ext-push-pull;
+	aspeed,ext-active-high;
+	aspeed,ext-pulse-duration = <256>;
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-catalina.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-catalina.dts
new file mode 100644
index 000000000000..14dd0ab64130
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-catalina.dts
@@ -0,0 +1,1222 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2021 Facebook Inc.
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/usb/pd.h>
+#include <dt-bindings/leds/leds-pca955x.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/i2c/i2c.h>
+
+/ {
+	model = "Facebook Catalina BMC";
+	compatible = "facebook,catalina-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial0 = &uart1;
+		serial2 = &uart3;
+		serial3 = &uart4;
+		serial4 = &uart5;
+		i2c16 = &i2c1mux0ch0;
+		i2c17 = &i2c1mux0ch1;
+		i2c18 = &i2c1mux0ch2;
+		i2c19 = &i2c1mux0ch3;
+		i2c20 = &i2c1mux0ch4;
+		i2c21 = &i2c1mux0ch5;
+		i2c22 = &i2c1mux0ch6;
+		i2c23 = &i2c1mux0ch7;
+		i2c24 = &i2c0mux0ch0;
+		i2c25 = &i2c0mux0ch1;
+		i2c26 = &i2c0mux0ch2;
+		i2c27 = &i2c0mux0ch3;
+		i2c28 = &i2c0mux1ch0;
+		i2c29 = &i2c0mux1ch1;
+		i2c30 = &i2c0mux1ch2;
+		i2c31 = &i2c0mux1ch3;
+		i2c32 = &i2c0mux2ch0;
+		i2c33 = &i2c0mux2ch1;
+		i2c34 = &i2c0mux2ch2;
+		i2c35 = &i2c0mux2ch3;
+		i2c36 = &i2c0mux3ch0;
+		i2c37 = &i2c0mux3ch1;
+		i2c38 = &i2c0mux3ch2;
+		i2c39 = &i2c0mux3ch3;
+		i2c40 = &i2c0mux4ch0;
+		i2c41 = &i2c0mux4ch1;
+		i2c42 = &i2c0mux4ch2;
+		i2c43 = &i2c0mux4ch3;
+		i2c44 = &i2c0mux5ch0;
+		i2c45 = &i2c0mux5ch1;
+		i2c46 = &i2c0mux5ch2;
+		i2c47 = &i2c0mux5ch3;
+		i2c48 = &i2c5mux0ch0;
+		i2c49 = &i2c5mux0ch1;
+		i2c50 = &i2c5mux0ch2;
+		i2c51 = &i2c5mux0ch3;
+		i2c52 = &i2c5mux0ch4;
+		i2c53 = &i2c5mux0ch5;
+		i2c54 = &i2c5mux0ch6;
+		i2c55 = &i2c5mux0ch7;
+	};
+
+	chosen {
+		stdout-path = "serial4:57600n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+			      <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+			      <&adc1 2>;
+	};
+
+	spi1_gpio: spi {
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sck-gpios = <&gpio0 ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio0 ASPEED_GPIO(Z, 4) GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpio0 ASPEED_GPIO(Z, 5) GPIO_ACTIVE_HIGH>;
+		cs-gpios = <&gpio0 ASPEED_GPIO(Z, 0) GPIO_ACTIVE_LOW>;
+		num-chipselects = <1>;
+
+		tpm@0 {
+			compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
+			spi-max-frequency = <33000000>;
+			reg = <0>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "bmc_heartbeat_amber";
+			gpios = <&gpio0 ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-1 {
+			label = "fp_id_amber";
+			default-state = "off";
+			gpios = <&gpio0 ASPEED_GPIO(B, 5) GPIO_ACTIVE_HIGH>;
+		};
+
+		led-2 {
+			label = "bmc_ready_noled";
+			gpios = <&gpio0 ASPEED_GPIO(B, 3) (GPIO_ACTIVE_HIGH|GPIO_TRANSITORY)>;
+		};
+
+		led-3 {
+			label = "bmc_ready_cpld_noled";
+			gpios = <&gpio0 ASPEED_GPIO(P, 5) (GPIO_ACTIVE_HIGH|GPIO_TRANSITORY)>;
+		};
+	};
+
+	p1v8_bmc_aux: regulator-p1v8-bmc-aux {
+		compatible = "regulator-fixed";
+		regulator-name = "p1v8_bmc_aux";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	p2v5_bmc_aux: regulator-p2v5-bmc-aux {
+		compatible = "regulator-fixed";
+		regulator-name = "p2v5_bmc_aux";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&mac2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ncsi3_default>;
+	use-ncsi;
+};
+
+&mac3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ncsi4_default>;
+	use-ncsi;
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-128.dtsi"
+	};
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "alt-bmc";
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+	multi-master;
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9546";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c0mux0ch0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			mctp-controller;
+
+			// IOB0 NIC0 TEMP
+			temperature-sensor@1f {
+				compatible = "ti,tmp421";
+				reg = <0x1f>;
+			};
+		};
+		i2c0mux0ch1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+		i2c0mux0ch2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			mctp-controller;
+
+			// IOB0 NIC1 TEMP
+			temperature-sensor@1f {
+				compatible = "ti,tmp421";
+				reg = <0x1f>;
+			};
+		};
+		i2c0mux0ch3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+
+	i2c-mux@72 {
+		compatible = "nxp,pca9546";
+		reg = <0x72>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c0mux1ch0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+		i2c0mux1ch1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			// IO Mezz 0 IOEXP
+			io_expander7: gpio@20 {
+				compatible = "nxp,pca9535";
+				reg = <0x20>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			// IO Mezz 0 FRU EEPROM
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+		i2c0mux1ch2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+		i2c0mux1ch3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+
+	i2c-mux@73 {
+		compatible = "nxp,pca9546";
+		reg = <0x73>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c0mux2ch0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+		i2c0mux2ch1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+		i2c0mux2ch2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+		i2c0mux2ch3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+
+	i2c-mux@75 {
+		compatible = "nxp,pca9546";
+		reg = <0x75>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c0mux3ch0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			mctp-controller;
+
+			// IOB1 NIC0 TEMP
+			temperature-sensor@1f {
+				compatible = "ti,tmp421";
+				reg = <0x1f>;
+			};
+		};
+		i2c0mux3ch1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+		i2c0mux3ch2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			mctp-controller;
+
+			// IOB1 NIC1 TEMP
+			temperature-sensor@1f {
+				compatible = "ti,tmp421";
+				reg = <0x1f>;
+			};
+		};
+		i2c0mux3ch3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+
+	i2c-mux@76 {
+		compatible = "nxp,pca9546";
+		reg = <0x76>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c0mux4ch0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+		i2c0mux4ch1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			// IO Mezz 1 IOEXP
+			io_expander8: gpio@21 {
+				compatible = "nxp,pca9535";
+				reg = <0x21>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			// IO Mezz 1 FRU EEPROM
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+		i2c0mux4ch2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+		i2c0mux4ch3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+
+	i2c-mux@77 {
+		compatible = "nxp,pca9546";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c0mux5ch0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+		i2c0mux5ch1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+		i2c0mux5ch2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+		i2c0mux5ch3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		i2c1mux0ch0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+
+			power-sensor@22 {
+				compatible = "mps,mp5990";
+				reg = <0x22>;
+			};
+		};
+		i2c1mux0ch1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+		};
+		i2c1mux0ch2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+
+			fanctl2: fan-controller@1 {
+				compatible = "nuvoton,nct7363";
+				reg = <0x01>;
+				#pwm-cells = <2>;
+
+				fan-9 {
+					pwms = <&fanctl2 0 40000>;
+					tach-ch = /bits/ 8 <0x09>;
+				};
+				fan-11 {
+					pwms = <&fanctl2 0 40000>;
+					tach-ch = /bits/ 8 <0x0b>;
+				};
+				fan-10 {
+					pwms = <&fanctl2 4 40000>;
+					tach-ch = /bits/ 8 <0x0a>;
+				};
+				fan-13 {
+					pwms = <&fanctl2 4 40000>;
+					tach-ch = /bits/ 8 <0x0d>;
+				};
+				fan-15 {
+					pwms = <&fanctl2 6 40000>;
+					tach-ch = /bits/ 8 <0x0f>;
+				};
+				fan-1 {
+					pwms = <&fanctl2 6 40000>;
+					tach-ch = /bits/ 8 <0x01>;
+				};
+				fan-0 {
+					pwms = <&fanctl2 10 40000>;
+					tach-ch = /bits/ 8 <0x00>;
+				};
+				fan-3 {
+					pwms = <&fanctl2 10 40000>;
+					tach-ch = /bits/ 8 <0x03>;
+				};
+			};
+			fanctl3: fan-controller@2 {
+				compatible = "nuvoton,nct7363";
+				reg = <0x02>;
+				#pwm-cells = <2>;
+
+				fan-9 {
+					pwms = <&fanctl3 0 40000>;
+					tach-ch = /bits/ 8 <0x09>;
+				};
+				fan-11 {
+					pwms = <&fanctl3 0 40000>;
+					tach-ch = /bits/ 8 <0x0b>;
+				};
+				fan-10 {
+					pwms = <&fanctl3 4 40000>;
+					tach-ch = /bits/ 8 <0x0a>;
+				};
+				fan-13 {
+					pwms = <&fanctl3 4 40000>;
+					tach-ch = /bits/ 8 <0x0d>;
+				};
+				fan-15 {
+					pwms = <&fanctl3 6 40000>;
+					tach-ch = /bits/ 8 <0x0f>;
+				};
+				fan-1 {
+					pwms = <&fanctl3 6 40000>;
+					tach-ch = /bits/ 8 <0x01>;
+				};
+				fan-0 {
+					pwms = <&fanctl3 10 40000>;
+					tach-ch = /bits/ 8 <0x00>;
+				};
+				fan-3 {
+					pwms = <&fanctl3 10 40000>;
+					tach-ch = /bits/ 8 <0x03>;
+				};
+			};
+			fanctl0: fan-controller@21 {
+				compatible = "maxim,max31790";
+				reg = <0x21>;
+			};
+			fanctl1: fan-controller@27 {
+				compatible = "maxim,max31790";
+				reg = <0x27>;
+			};
+		};
+		i2c1mux0ch3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+		};
+		i2c1mux0ch4: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x4>;
+
+			power-monitor@13 {
+				compatible = "infineon,xdp710";
+				reg = <0x13>;
+			};
+			power-monitor@1c {
+				compatible = "infineon,xdp710";
+				reg = <0x1c>;
+			};
+			power-monitor@42 {
+				compatible = "lltc,ltc4287";
+				reg = <0x42>;
+				shunt-resistor-micro-ohms = <100>;
+			};
+			power-monitor@43 {
+				compatible = "lltc,ltc4287";
+				reg = <0x43>;
+				shunt-resistor-micro-ohms = <100>;
+			};
+		};
+		i2c1mux0ch5: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x5>;
+
+			// PDB FRU EEPROM
+			eeprom@54 {
+				compatible = "atmel,24c64";
+				reg = <0x54>;
+			};
+
+			// PDB TEMP SENSOR
+			temperature-sensor@4f {
+				compatible = "ti,tmp75";
+				reg = <0x4f>;
+			};
+		};
+		i2c1mux0ch6: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x6>;
+
+			// PDB IOEXP
+			io_expander5: gpio@27 {
+				compatible = "nxp,pca9554";
+				reg = <0x27>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			// OSFP IOEXP
+			io_expander6: gpio@25 {
+				compatible = "nxp,pca9555";
+				reg = <0x25>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			// OSFP FRU EEPROM
+			eeprom@51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+		};
+		i2c1mux0ch7: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x7>;
+
+			// FIO FRU EEPROM
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+
+			// FIO TEMP SENSOR
+			temperature-sensor@4b {
+				compatible = "ti,tmp75";
+				reg = <0x4b>;
+			};
+
+			// FIO REMOTE TEMP SENSOR
+			temperature-sensor@4f {
+				compatible = "ti,tmp75";
+				reg = <0x4f>;
+			};
+		};
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	// Module 0 IOEXP
+	io_expander0: gpio@20 {
+		compatible = "nxp,pca9555";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	// Module 1 IOEXP
+	io_expander1: gpio@21 {
+		compatible = "nxp,pca9555";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	// HMC IOEXP
+	io_expander2: gpio@27 {
+		compatible = "nxp,pca9555";
+		reg = <0x27>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	// Module 0 EEPROM
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	// Module 1 EEPROM
+	eeprom@51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c5mux0ch0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+		i2c5mux0ch1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+		i2c5mux0ch2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+		i2c5mux0ch3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+		i2c5mux0ch4: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+		i2c5mux0ch5: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+		i2c5mux0ch6: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+			// HDD FRU EEPROM
+			eeprom@52 {
+				compatible = "atmel,24c64";
+				reg = <0x52>;
+			};
+		};
+		i2c5mux0ch7: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+&i2c6 {
+	status = "okay";
+
+	// BMC IOEXP on Module 0
+	io_expander3: gpio@21 {
+		compatible = "nxp,pca9555";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	rtc@6f {
+		compatible = "nuvoton,nct3018y";
+		reg = <0x6f>;
+	};
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+
+	// SCM CPLD IOEXP
+	io_expander4: gpio@4f {
+		compatible = "nxp,pca9555";
+		reg = <0x4f>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	// SCM TEMP SENSOR
+	temperature-sensor@4b {
+		compatible = "ti,tmp75";
+		reg = <0x4b>;
+	};
+
+	// SCM FRU EEPROM
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	// BSM FRU EEPROM
+	eeprom@56 {
+		compatible = "atmel,24c64";
+		reg = <0x56>;
+	};
+};
+
+&i2c10 {
+	status = "okay";
+	multi-master;
+	mctp-controller;
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	// OCP NIC0 TEMP
+	temperature-sensor@1f {
+		compatible = "ti,tmp421";
+		reg = <0x1f>;
+	};
+
+	// OCP NIC0 FRU EEPROM
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+};
+
+&i2c11 {
+	status = "okay";
+
+	ssif-bmc@10 {
+		compatible = "ssif-bmc";
+		reg = <0x10>;
+	};
+};
+
+&i2c12 {
+	status = "okay";
+	multi-master;
+
+	// Module 1 FRU EEPROM
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	// Secondary CBC FRU EEPROM
+	eeprom@54 {
+		compatible = "atmel,24c02";
+		reg = <0x54>;
+	};
+};
+
+&i2c13 {
+	status = "okay";
+	multi-master;
+
+	// Module 0 FRU EEPROM
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	// Primary CBC FRU EEPROM
+	eeprom@54 {
+		compatible = "atmel,24c02";
+		reg = <0x54>;
+	};
+
+	// HMC FRU EEPROM
+	eeprom@57 {
+		compatible = "atmel,24c02";
+		reg = <0x57>;
+	};
+};
+
+&i2c14 {
+	status = "okay";
+
+	// PDB CPLD IOEXP 0x10
+	io_expander9: gpio@10 {
+		compatible = "nxp,pca9555";
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
+		reg = <0x10>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	// PDB CPLD IOEXP 0x11
+	io_expander10: gpio@11 {
+		compatible = "nxp,pca9555";
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
+		reg = <0x11>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	// PDB CPLD IOEXP 0x12
+	io_expander11: gpio@12 {
+		compatible = "nxp,pca9555";
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
+		reg = <0x12>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	// PDB CPLD IOEXP 0x13
+	io_expander12: gpio@13 {
+		compatible = "nxp,pca9555";
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
+		reg = <0x13>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	// PDB CPLD IOEXP 0x14
+	io_expander13: gpio@14 {
+		compatible = "nxp,pca9555";
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
+		reg = <0x14>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	// PDB CPLD IOEXP 0x15
+	io_expander14: gpio@15 {
+		compatible = "nxp,pca9555";
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
+		reg = <0x15>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+};
+
+&i2c15 {
+	status = "okay";
+	multi-master;
+	mctp-controller;
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	// OCP NIC1 TEMP
+	temperature-sensor@1f {
+		compatible = "ti,tmp421";
+		reg = <0x1f>;
+	};
+
+	// OCP NIC1 FRU EEPROM
+	eeprom@52 {
+		compatible = "atmel,24c64";
+		reg = <0x52>;
+	};
+};
+
+&adc0 {
+	vref-supply = <&p1v8_bmc_aux>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+		&pinctrl_adc2_default &pinctrl_adc3_default
+		&pinctrl_adc4_default &pinctrl_adc5_default
+		&pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+	vref-supply = <&p2v5_bmc_aux>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc10_default>;
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&wdt1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst1_default>;
+	aspeed,reset-type = "soc";
+	aspeed,external-signal;
+	aspeed,ext-push-pull;
+	aspeed,ext-active-high;
+	aspeed,ext-pulse-duration = <256>;
+};
+
+&pinctrl {
+	pinctrl_ncsi3_default: ncsi3_default {
+		function = "RMII3";
+		groups = "NCSI3";
+	};
+
+	pinctrl_ncsi4_default: ncsi4_default {
+		function = "RMII4";
+		groups = "NCSI4";
+	};
+};
+
+&gpio0 {
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","","","",
+	/*B0-B7*/	"BATTERY_DETECT","PRSNT1_HPM_SCM_N",
+			"BMC_I2C1_FPGA_ALERT_L","BMC_READY",
+			"IOEXP_INT_L","FM_ID_LED",
+			"","",
+	/*C0-C7*/	"","","","",
+			"PMBUS_REQ_N","PSU_FW_UPDATE_REQ_N",
+			"","BMC_I2C_SSIF_ALERT_L",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"","","","","","","","",
+	/*F0-F7*/	"","","","","","","","",
+	/*G0-G7*/	"","","","","","",
+			"FM_DEBUG_PORT_PRSNT_N","FM_BMC_DBP_PRESENT_N",
+	/*H0-H7*/	"PWR_BRAKE_L","RUN_POWER_EN",
+			"SHDN_FORCE_L","SHDN_REQ_L",
+			"","","","",
+	/*I0-I7*/	"","","","",
+			"","FLASH_WP_STATUS",
+			"FM_PDB_HEALTH_N","RUN_POWER_PG",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"PCIE_EP_RST_EN","BMC_FRU_WP",
+			"SCM_HPM_STBY_RST_N","SCM_HPM_STBY_EN",
+			"STBY_POWER_PG_3V3","TH500_SHDN_OK_L","","",
+	/*N0-N7*/	"LED_POSTCODE_0","LED_POSTCODE_1",
+			"LED_POSTCODE_2","LED_POSTCODE_3",
+			"LED_POSTCODE_4","LED_POSTCODE_5",
+			"LED_POSTCODE_6","LED_POSTCODE_7",
+	/*O0-O7*/	"HMC_I2C3_FPGA_ALERT_L","FPGA_READY_HMC",
+			"CHASSIS_AC_LOSS_L","BSM_PRSNT_R_N",
+			"PSU_SMB_ALERT_L","FM_TPM_PRSNT_0_N",
+			"","USBDBG_IPMI_EN_L",
+	/*P0-P7*/	"PWR_BTN_BMC_N","IPEX_CABLE_PRSNT_L",
+			"ID_RST_BTN_BMC_N","RST_BMC_RSTBTN_OUT_N",
+			"host0-ready","BMC_READY_CPLD","","BMC_HEARTBEAT_N",
+	/*Q0-Q7*/	"IRQ_PCH_TPM_SPI_N","USB_OC0_REAR_R_N",
+			"UART_MUX_SEL","I2C_MUX_RESET_L",
+			"RSVD_NV_PLT_DETECT","SPI_TPM_INT_L",
+			"CPU_JTAG_MUX_SELECT","THERM_BB_OVERT_L",
+	/*R0-R7*/	"THERM_BB_WARN_L","SPI_BMC_FPGA_INT_L",
+			"CPU_BOOT_DONE","PMBUS_GNT_L",
+			"CHASSIS_PWR_BRK_L","PCIE_WAKE_L",
+			"PDB_THERM_OVERT_L","HMC_I2C2_FPGA_ALERT_L",
+	/*S0-S7*/	"","","SYS_BMC_PWRBTN_R_N","FM_TPM_PRSNT_1_N",
+			"FM_BMC_DEBUG_SW_N","UID_LED_N",
+			"SYS_FAULT_LED_N","RUN_POWER_FAULT_L",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"L2_RST_REQ_OUT_L","L0L1_RST_REQ_OUT_L",
+			"BMC_ID_BEEP_SEL","BMC_I2C0_FPGA_ALERT_L",
+			"SMB_BMC_TMP_ALERT","PWR_LED_N",
+			"SYS_RST_OUT_L","IRQ_TPM_SPI_N",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","RST_BMC_SELF_HW",
+			"FM_FLASH_LATCH_N","BMC_EMMC_RST_N",
+			"","","","",
+	/*Z0-Z7*/	"","","","","","","","";
+};
+
+&io_expander0 {
+	gpio-line-names =
+		"FPGA_THERM_OVERT_L","FPGA_READY_BMC",
+		"HMC_BMC_DETECT","HMC_PGOOD",
+		"","BMC_SELF_PWR_CYCLE",
+		"FPGA_EROT_FATAL_ERROR_L","WP_HW_EXT_CTRL_L",
+		"EROT_FPGA_RST_L","FPGA_EROT_RECOVERY_L",
+		"BMC_EROT_FPGA_SPI_MUX_SEL","USB2_HUB_RESET_L",
+		"NCSI_CS1_SEL","SGPIO_EN_L",
+		"B2B_IOEXP_INT_L","I2C_BUS_MUX_RESET_L";
+};
+
+&io_expander1 {
+	gpio-line-names =
+		"SEC_FPGA_THERM_OVERT_L","SEC_FPGA_READY_BMC",
+		"","",
+		"","",
+		"SEC_FPGA_EROT_FATAL_ERROR_L","SEC_WP_HW_EXT_CTRL_L",
+		"SEC_EROT_FPGA_RST_L","SEC_FPGA_EROT_RECOVERY_L",
+		"SEC_BMC_EROT_FPGA_SPI_MUX_SEL","",
+		"","",
+		"","SEC_I2C_BUS_MUX_RESET_L";
+};
+
+&io_expander2 {
+	gpio-line-names =
+		"HMC_PRSNT_L","HMC_READY",
+		"HMC_EROT_FATAL_ERROR_L","I2C_MUX_SEL",
+		"HMC_EROT_SPI_MUX_SEL","HMC_EROT_RECOVERY_L",
+		"HMC_EROT_RST_L","GLOBAL_WP_HMC",
+		"FPGA_RST_L","USB2_HUB_RST",
+		"CPU_UART_MUX_SEL","",
+		"","","","";
+};
+
+&io_expander3 {
+	gpio-line-names =
+		"RTC_MUX_SEL","PCI_MUX_SEL","TPM_MUX_SEL","FAN_MUX-SEL",
+		"SGMII_MUX_SEL","DP_MUX_SEL","UPHY3_USB_SEL","NCSI_MUX_SEL",
+		"BMC_PHY_RST","RTC_CLR_L","BMC_12V_CTRL","PS_RUN_IO0_PG",
+		"","","","";
+};
+
+&io_expander4 {
+	gpio-line-names =
+		"stby_power_en_cpld","stby_power_gd_cpld","","",
+		"","","","",
+		"","","","",
+		"","","","";
+};
+
+&io_expander5 {
+	gpio-line-names =
+		"JTAG_MUX_SEL","IOX_BMC_RESET","","",
+		"","","","";
+};
+
+&io_expander6 {
+	gpio-line-names =
+		"OSFP_PHASE_ID0","OSFP_PHASE_ID1",
+		"OSFP_PHASE_ID2","OSFP_PHASE_ID3",
+		"","","","",
+		"OSFP_BOARD_ID0","OSFP_BOARD_ID1",
+		"OSFP_BOARD_ID2","PWRGD_P3V3_N1",
+		"PWRGD_P3V3_N2","","","";
+};
+
+&io_expander7 {
+	gpio-line-names =
+		"RST_CX7_0","RST_CX7_1",
+		"CX0_SSD0_PRSNT_L","CX1_SSD1_PRSNT_L",
+		"CX_BOOT_CMPLT_CX0","CX_BOOT_CMPLT_CX1",
+		"CX_TWARN_CX0_L","CX_TWARN_CX1_L",
+		"CX_OVT_SHDN_CX0","CX_OVT_SHDN_CX1",
+		"FNP_L_CX0","FNP_L_CX1",
+		"","MCU_GPIO","MCU_RST_N","MCU_RECOVERY_N";
+};
+
+&io_expander8 {
+	gpio-line-names =
+		"SEC_RST_CX7_0","SEC_RST_CX7_1",
+		"SEC_CX0_SSD0_PRSNT_L","SEC_CX1_SSD1_PRSNT_L",
+		"SEC_CX_BOOT_CMPLT_CX0","SEC_CX_BOOT_CMPLT_CX1",
+		"SEC_CX_TWARN_CX0_L","SEC_CX_TWARN_CX1_L",
+		"SEC_CX_OVT_SHDN_CX0","SEC_CX_OVT_SHDN_CX1",
+		"SEC_FNP_L_CX0","SEC_FNP_L_CX1",
+		"","SEC_MCU_GPIO","SEC_MCU_RST_N","SEC_MCU_RECOVERY_N";
+};
+
+&io_expander9 {
+	gpio-line-names =
+		"LEAK3_DETECT_R","LEAK1_DETECT_R",
+		"LEAK2_DETECT_R","LEAK0_DETECT_R",
+		"CHASSIS3_LEAK_Q_N_PLD","CHASSIS1_LEAK_Q_N_PLD",
+		"CHASSIS2_LEAK_Q_N_PLD","CHASSIS0_LEAK_Q_N_PLD",
+		"P12V_AUX_FAN_ALERT_PLD_N","P12V_AUX_FAN_OC_PLD_N",
+		"P12V_AUX_FAN_FAULT_PLD_N","LEAK_DETECT_RMC_N_R",
+		"RSVD_RMC_GPIO3_R","SMB_RJ45_FIO_TMP_ALERT",
+		"","";
+};
+
+&io_expander10 {
+	gpio-line-names =
+		"FM_P12V_NIC1_FLTB_R_N","FM_P3V3_NIC1_FAULT_R_N",
+		"OCP_V3_2_PWRBRK_FROM_HOST_ISO_PLD_N",
+		"P12V_AUX_NIC1_SENSE_ALERT_R_N",
+		"FM_P12V_NIC0_FLTB_R_N","FM_P3V3_NIC0_FAULT_R_N",
+		"OCP_SFF_PWRBRK_FROM_HOST_ISO_PLD_N",
+		"P12V_AUX_NIC0_SENSE_ALERT_R_N",
+		"P12V_AUX_PSU_SMB_ALERT_R_L","P12V_SCM_SENSE_ALERT_R_N",
+		"NODEB_PSU_SMB_ALERT_R_L","NODEA_PSU_SMB_ALERT_R_L",
+		"P52V_SENSE_ALERT_PLD_N","P48V_HS2_FAULT_N_PLD",
+		"P48V_HS1_FAULT_N_PLD","";
+};
+
+&io_expander11 {
+	gpio-line-names =
+		"FAN_7_PRESENT_N","FAN_6_PRESENT_N",
+		"FAN_5_PRESENT_N","FAN_4_PRESENT_N",
+		"FAN_3_PRESENT_N","FAN_2_PRESENT_N",
+		"FAN_1_PRESENT_N","FAN_0_PRESENT_N",
+		"PRSNT_CHASSIS3_LEAK_CABLE_R_N","PRSNT_CHASSIS1_LEAK_CABLE_R_N",
+		"PRSNT_CHASSIS2_LEAK_CABLE_R_N","PRSNT_CHASSIS0_LEAK_CABLE_R_N",
+		"PRSNT_RJ45_FIO_N_R","PRSNT_HDDBD_POWER_CABLE_N",
+		"PRSNT_OSFP_POWER_CABLE_N","";
+};
+
+&io_expander12 {
+	gpio-line-names =
+		"RST_OCP_V3_1_R_N","NIC0_PERST_N",
+		"OCP_SFF_PERST_FROM_HOST_ISO_PLD_N","OCP_SFF_MAIN_PWR_EN",
+		"FM_OCP_SFF_PWR_GOOD_PLD","OCP_SFF_AUX_PWR_PLD_EN_R",
+		"HP_LVC3_OCP_V3_1_PWRGD_PLD","HP_OCP_V3_1_HSC_PWRGD_PLD_R",
+		"RST_OCP_V3_2_R_N","NIC1_PERST_N",
+		"OCP_V3_2_PERST_FROM_HOST_ISO_PLD_N","OCP_V3_2_MAIN_PWR_EN",
+		"FM_OCP_V3_2_PWR_GOOD_PLD","OCP_V3_2_AUX_PWR_PLD_EN_R",
+		"HP_LVC3_OCP_V3_2_PWRGD_PLD","HP_OCP_V3_2_HSC_PWRGD_PLD_R";
+};
+
+&io_expander13 {
+	gpio-line-names =
+		"NODEA_NODEB_PWOK_PLD_ISO_R","PWR_EN_NICS",
+		"PWRGD_P12V_AUX_FAN_PLD","P12V_AUX_FAN_EN_PLD",
+		"PWRGD_P3V3_AUX_PLD","PWRGD_P12V_AUX_PLD_ISO_R",
+		"FM_MAIN_PWREN_FROM_RMC_R","FM_MAIN_PWREN_RMC_EN_ISO_R",
+		"PWRGD_RMC_R","PWRGD_P12V_AUX_FAN_PLD",
+		"P12V_AUX_FAN_EN_PLD","FM_SYS_THROTTLE_N",
+		"HP_LVC3_OCP_V3_2_PRSNT2_PLD_N","HP_LVC3_OCP_V3_1_PRSNT2_PLD_N",
+		"","";
+};
+
+&io_expander14 {
+	gpio-line-names =
+		"","","","","","","","",
+		"FM_BOARD_BMC_SKU_ID3","FM_BOARD_BMC_SKU_ID2",
+		"FM_BOARD_BMC_SKU_ID1","FM_BOARD_BMC_SKU_ID0",
+		"FAB_BMC_REV_ID2","FAB_BMC_REV_ID1",
+		"FAB_BMC_REV_ID0","";
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dts
new file mode 100644
index 000000000000..ecef44d89977
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-clemente.dts
@@ -0,0 +1,1283 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2021 Facebook Inc.
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/usb/pd.h>
+#include <dt-bindings/leds/leds-pca955x.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/i2c/i2c.h>
+
+/ {
+	model = "Facebook Clemente BMC";
+	compatible = "facebook,clemente-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial0 = &uart1;
+		serial2 = &uart3;
+		serial3 = &uart4;
+		serial4 = &uart5;
+		i2c16 = &i2c1mux0ch0;
+		i2c17 = &i2c1mux0ch1;
+		i2c18 = &i2c1mux0ch2;
+		i2c19 = &i2c1mux0ch3;
+		i2c20 = &i2c1mux0ch4;
+		i2c21 = &i2c1mux0ch5;
+		i2c22 = &i2c1mux0ch6;
+		i2c23 = &i2c1mux0ch7;
+		i2c24 = &i2c0mux0ch0;
+		i2c25 = &i2c0mux0ch1;
+		i2c26 = &i2c0mux0ch2;
+		i2c27 = &i2c0mux0ch3;
+		i2c28 = &i2c0mux1ch0;
+		i2c29 = &i2c0mux1ch1;
+		i2c30 = &i2c0mux1ch2;
+		i2c31 = &i2c0mux1ch3;
+		i2c32 = &i2c0mux2ch0;
+		i2c33 = &i2c0mux2ch1;
+		i2c34 = &i2c0mux2ch2;
+		i2c35 = &i2c0mux2ch3;
+		i2c36 = &i2c0mux3ch0;
+		i2c37 = &i2c0mux3ch1;
+		i2c38 = &i2c0mux3ch2;
+		i2c39 = &i2c0mux3ch3;
+		i2c40 = &i2c0mux4ch0;
+		i2c41 = &i2c0mux4ch1;
+		i2c42 = &i2c0mux4ch2;
+		i2c43 = &i2c0mux4ch3;
+		i2c44 = &i2c0mux5ch0;
+		i2c45 = &i2c0mux5ch1;
+		i2c46 = &i2c0mux5ch2;
+		i2c47 = &i2c0mux5ch3;
+		i2c48 = &i2c0mux0ch1mux0ch0;
+		i2c49 = &i2c0mux0ch1mux0ch1;
+		i2c50 = &i2c0mux0ch1mux0ch2;
+		i2c51 = &i2c0mux0ch1mux0ch3;
+		i2c52 = &i2c0mux3ch1mux0ch0;
+		i2c53 = &i2c0mux3ch1mux0ch1;
+		i2c54 = &i2c0mux3ch1mux0ch2;
+		i2c55 = &i2c0mux3ch1mux0ch3;
+	};
+
+	chosen {
+		stdout-path = "serial4:57600n8";
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+			      <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+			      <&adc1 2>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "bmc_heartbeat_amber";
+			gpios = <&gpio0 ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-1 {
+			label = "fp_id_amber";
+			default-state = "off";
+			gpios = <&gpio0 ASPEED_GPIO(B, 5) GPIO_ACTIVE_HIGH>;
+		};
+
+		led-2 {
+			label = "bmc_ready_noled";
+			gpios = <&gpio0 ASPEED_GPIO(B, 3) (GPIO_ACTIVE_HIGH|GPIO_TRANSITORY)>;
+		};
+
+		led-3 {
+			label = "bmc_ready_cpld_noled";
+			gpios = <&gpio0 ASPEED_GPIO(P, 5) (GPIO_ACTIVE_HIGH|GPIO_TRANSITORY)>;
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	p1v8_bmc_aux: regulator-p1v8-bmc-aux {
+		compatible = "regulator-fixed";
+		regulator-name = "p1v8_bmc_aux";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	p2v5_bmc_aux: regulator-p2v5-bmc-aux {
+		compatible = "regulator-fixed";
+		regulator-name = "p2v5_bmc_aux";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		ramoops@b3e00000 {
+			compatible = "ramoops";
+			reg = <0xbb000000 0x200000>; /* 16 * (4 * 0x8000) */
+			record-size = <0x8000>;
+			console-size = <0x8000>;
+			ftrace-size = <0x8000>;
+			pmsg-size = <0x8000>;
+			max-reason = <3>;
+		};
+	};
+
+	spi1_gpio: spi {
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sck-gpios = <&gpio0 ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio0 ASPEED_GPIO(Z, 4) GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpio0 ASPEED_GPIO(Z, 5) GPIO_ACTIVE_HIGH>;
+		cs-gpios = <&gpio0 ASPEED_GPIO(Z, 0) GPIO_ACTIVE_LOW>;
+		num-chipselects = <1>;
+
+		tpm@0 {
+			compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
+			spi-max-frequency = <33000000>;
+			reg = <0>;
+		};
+	};
+};
+
+&adc0 {
+	vref-supply = <&p1v8_bmc_aux>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+		&pinctrl_adc2_default &pinctrl_adc3_default
+		&pinctrl_adc4_default &pinctrl_adc5_default
+		&pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+	vref-supply = <&p2v5_bmc_aux>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc10_default>;
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-128.dtsi"
+	};
+
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "alt-bmc";
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&gpio0 {
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","","","",
+	/*B0-B7*/	"BATTERY_DETECT","PRSNT1_HPM_SCM_N",
+			"BMC_I2C1_FPGA_ALERT_L","BMC_READY",
+			"IOEXP_INT_L","FM_ID_LED",
+			"","",
+	/*C0-C7*/	"BMC_GPIOC0","","","",
+			"PMBUS_REQ_N","PSU_FW_UPDATE_REQ_N",
+			"","BMC_I2C_SSIF_ALERT_L",
+	/*D0-D7*/	"","","","","BMC_GPIOD4","","","",
+	/*E0-E7*/	"BMC_GPIOE0","BMC_GPIOE1","","","","","","",
+	/*F0-F7*/	"","","","","","","","",
+	/*G0-G7*/	"","","","","","",
+			"FM_DEBUG_PORT_PRSNT_N","FM_BMC_DBP_PRESENT_N",
+	/*H0-H7*/	"PWR_BRAKE_L","RUN_POWER_EN",
+			"SHDN_FORCE_L","SHDN_REQ_L",
+			"","","","",
+	/*I0-I7*/	"","","","",
+			"","FLASH_WP_STATUS",
+			"FM_PDB_HEALTH_N","RUN_POWER_PG",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"PCIE_EP_RST_EN","BMC_FRU_WP",
+			"SCM_HPM_STBY_RST_N","SCM_HPM_STBY_EN",
+			"STBY_POWER_PG_3V3","TH500_SHDN_OK_L","","",
+	/*N0-N7*/	"LED_POSTCODE_0","LED_POSTCODE_1",
+			"LED_POSTCODE_2","LED_POSTCODE_3",
+			"LED_POSTCODE_4","LED_POSTCODE_5",
+			"LED_POSTCODE_6","LED_POSTCODE_7",
+	/*O0-O7*/	"HMC_I2C3_FPGA_ALERT_L","FPGA_READY_HMC",
+			"CHASSIS_AC_LOSS_L","BSM_PRSNT_R_N",
+			"PSU_SMB_ALERT_L","FM_TPM_PRSNT_0_N",
+			"","USBDBG_IPMI_EN_L",
+	/*P0-P7*/	"PWR_BTN_BMC_N","IPEX_CABLE_PRSNT_L",
+			"ID_RST_BTN_BMC_N","RST_BMC_RSTBTN_OUT_N",
+			"host0-ready","BMC_READY_CPLD","BMC_GPIOP6","BMC_HEARTBEAT_N",
+	/*Q0-Q7*/	"IRQ_PCH_TPM_SPI_N","USB_OC0_REAR_R_N",
+			"UART_MUX_SEL","I2C_MUX_RESET_L",
+			"RSVD_NV_PLT_DETECT","SPI_TPM_INT_L",
+			"CPU_JTAG_MUX_SELECT","THERM_BB_OVERT_L",
+	/*R0-R7*/	"THERM_BB_WARN_L","SPI_BMC_FPGA_INT_L",
+			"CPU_BOOT_DONE","PMBUS_GNT_L",
+			"CHASSIS_PWR_BRK_L","PCIE_WAKE_L",
+			"PDB_THERM_OVERT_L","HMC_I2C2_FPGA_ALERT_L",
+	/*S0-S7*/	"","","SYS_BMC_PWRBTN_R_N","FM_TPM_PRSNT_1_N",
+			"FM_BMC_DEBUG_SW_N","UID_LED_N",
+			"SYS_FAULT_LED_N","RUN_POWER_FAULT_L",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"L2_RST_REQ_OUT_L","L0L1_RST_REQ_OUT_L",
+			"BMC_ID_BEEP_SEL","BMC_I2C0_FPGA_ALERT_L",
+			"SMB_BMC_TMP_ALERT","PWR_LED_N",
+			"SYS_RST_OUT_L","IRQ_TPM_SPI_N",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","RST_BMC_SELF_HW",
+			"FM_FLASH_LATCH_N","BMC_EMMC_RST_N",
+			"BMC_GPIOY4","BMC_GPIOY5","","",
+	/*Z0-Z7*/	"","","","","","","BMC_GPIOZ6","BMC_GPIOZ7";
+};
+
+&gpio1 {
+	gpio-line-names =
+	/*18A0-18A7*/	"","","","","","","","",
+	/*18B0-18B3*/	"","","","",
+	/*18B4-18B7*/	"FM_BOARD_BMC_REV_ID0","FM_BOARD_BMC_REV_ID1","FM_BOARD_BMC_REV_ID2","",
+	/*18C0-18C7*/	"","","PI_BMC_BIOS_ROM_IRQ0_N","","","","","",
+	/*18D0-18D7*/	"","","","","","","","",
+	/*18E0-18E3*/	"","","","AC_PWR_BMC_BTN_N","","","","";
+};
+
+&i2c0 {
+	status = "okay";
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9546";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c0mux0ch0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c0mux0ch1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			// HDD FRU EEPROM
+			eeprom@56 {
+				compatible = "atmel,24c128";
+				reg = <0x56>;
+			};
+
+			// E1.S Backplane
+			i2c0mux0ch1mux0: i2c-mux@74 {
+				compatible = "nxp,pca9546";
+				reg = <0x74>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				i2c-mux-idle-disconnect;
+
+				i2c0mux0ch1mux0ch0: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				i2c0mux0ch1mux0ch1: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				i2c0mux0ch1mux0ch2: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				i2c0mux0ch1mux0ch3: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+			};
+		};
+
+		i2c0mux0ch2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c0mux0ch3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+
+	i2c-mux@72 {
+		compatible = "nxp,pca9546";
+		reg = <0x72>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c0mux1ch0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c0mux1ch1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			// IO Mezz 0 IOEXP
+			io_expander7: gpio@20 {
+				compatible = "nxp,pca9535";
+				reg = <0x20>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				gpio-line-names =
+					"RST_CX7_0",
+					"RST_CX7_1",
+					"CX0_SSD0_PRSNT_L",
+					"CX1_SSD1_PRSNT_L",
+					"CX_BOOT_CMPLT_CX0",
+					"CX_BOOT_CMPLT_CX1",
+					"CX_TWARN_CX0_L",
+					"CX_TWARN_CX1_L",
+					"CX_OVT_SHDN_CX0",
+					"CX_OVT_SHDN_CX1",
+					"FNP_L_CX0",
+					"FNP_L_CX1",
+					"",
+					"MCU_GPIO",
+					"MCU_RST_N",
+					"MCU_RECOVERY_N";
+			};
+
+			// IO Mezz 0 FRU EEPROM
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+
+			// OSFP 0 FRU EEPROM
+			eeprom@52 {
+				compatible = "atmel,24c128";
+				reg = <0x52>;
+			};
+		};
+
+		i2c0mux1ch2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c0mux1ch3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+
+	i2c-mux@73 {
+		compatible = "nxp,pca9546";
+		reg = <0x73>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c0mux2ch0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			// IOB0 NIC0 TEMP
+			temperature-sensor@1f {
+				compatible = "ti,tmp421";
+				reg = <0x1f>;
+			};
+		};
+
+		i2c0mux2ch1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		i2c0mux2ch2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c0mux2ch3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			// IOB0 NIC1 TEMP
+			temperature-sensor@1f {
+				compatible = "ti,tmp421";
+				reg = <0x1f>;
+			};
+		};
+	};
+
+	i2c-mux@75 {
+		compatible = "nxp,pca9546";
+		reg = <0x75>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c0mux3ch0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c0mux3ch1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			// E1.S Backplane HDD FRU EEPROM
+			eeprom@56 {
+				compatible = "atmel,24c128";
+				reg = <0x56>;
+			};
+
+			// E1.S Backplane MUX
+			i2c0mux3ch1mux0: i2c-mux@74 {
+				compatible = "nxp,pca9546";
+				reg = <0x74>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				i2c-mux-idle-disconnect;
+
+				i2c0mux3ch1mux0ch0: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				i2c0mux3ch1mux0ch1: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				i2c0mux3ch1mux0ch2: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				i2c0mux3ch1mux0ch3: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+			};
+		};
+
+		i2c0mux3ch2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c0mux3ch3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+
+	i2c-mux@76 {
+		compatible = "nxp,pca9546";
+		reg = <0x76>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c0mux4ch0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c0mux4ch1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			// IO Mezz 1 IOEXP
+			io_expander8: gpio@21 {
+				compatible = "nxp,pca9535";
+				reg = <0x21>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				gpio-line-names =
+					"SEC_RST_CX7_0",
+					"SEC_RST_CX7_1",
+					"SEC_CX0_SSD0_PRSNT_L",
+					"SEC_CX1_SSD1_PRSNT_L",
+					"SEC_CX_BOOT_CMPLT_CX0",
+					"SEC_CX_BOOT_CMPLT_CX1",
+					"SEC_CX_TWARN_CX0_L",
+					"SEC_CX_TWARN_CX1_L",
+					"SEC_CX_OVT_SHDN_CX0",
+					"SEC_CX_OVT_SHDN_CX1",
+					"SEC_FNP_L_CX0",
+					"SEC_FNP_L_CX1",
+					"",
+					"SEC_MCU_GPIO",
+					"SEC_MCU_RST_N",
+					"SEC_MCU_RECOVERY_N";
+			};
+
+			// IO Mezz 1 FRU EEPROM
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+
+			// OSFP 1 FRU EEPROM
+			eeprom@52 {
+				compatible = "atmel,24c128";
+				reg = <0x52>;
+			};
+		};
+
+		i2c0mux4ch2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c0mux4ch3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+
+	i2c-mux@77 {
+		compatible = "nxp,pca9546";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c0mux5ch0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			// IOB1 NIC0 TEMP
+			temperature-sensor@1f {
+				compatible = "ti,tmp421";
+				reg = <0x1f>;
+			};
+		};
+
+		i2c0mux5ch1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		i2c0mux5ch2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c0mux5ch3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			// IOB1 NIC1 TEMP
+			temperature-sensor@1f {
+				compatible = "ti,tmp421";
+				reg = <0x1f>;
+			};
+		};
+	};
+};
+
+&i2c1 {
+	status = "okay";
+
+	// PDB
+	power-monitor@12 {
+		compatible = "ti,lm5066i";
+		reg = <0x12>;
+	};
+
+	// PDB
+	power-monitor@14 {
+		compatible = "ti,lm5066i";
+		reg = <0x14>;
+	};
+
+	// Module 0
+	fanctl0: fan-controller@20{
+		compatible = "maxim,max31790";
+		reg = <0x20>;
+	};
+
+	// Module 0
+	fanctl1: fan-controller@23{
+		compatible = "maxim,max31790";
+		reg = <0x23>;
+	};
+
+	// Module 1
+	fanctl2: fan-controller@2c{
+		compatible = "maxim,max31790";
+		reg = <0x2c>;
+	};
+
+	// Module 1
+	fanctl3: fan-controller@2f{
+		compatible = "maxim,max31790";
+		reg = <0x2f>;
+	};
+
+	// Module 0 Leak Sensor
+	adc@34 {
+		compatible = "maxim,max1363";
+		reg = <0x34>;
+	};
+
+	// Module 1 Leak Sensor
+	adc@35 {
+		compatible = "maxim,max1363";
+		reg = <0x35>;
+	};
+
+	// PDB TEMP SENSOR
+	temperature-sensor@4e {
+		compatible = "ti,tmp1075";
+		reg = <0x4e>;
+	};
+
+	// PDB FRU EEPROM
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+	};
+
+	// PDB
+	vrm@60 {
+		compatible = "renesas,raa228004";
+		reg = <0x60>;
+	};
+
+	// PDB
+	vrm@61 {
+		compatible = "renesas,raa228004";
+		reg = <0x61>;
+	};
+
+	// Interposer
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		i2c1mux0ch0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+		};
+
+		i2c1mux0ch1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+		};
+
+		i2c1mux0ch2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+		};
+
+		i2c1mux0ch3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+		};
+
+		i2c1mux0ch4: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x4>;
+		};
+
+		i2c1mux0ch5: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x5>;
+
+			// Interposer TEMP SENSOR
+			temperature-sensor@4f {
+				compatible = "ti,tmp75";
+				reg = <0x4f>;
+			};
+
+			// Interposer FRU EEPROM
+			eeprom@54 {
+				compatible = "atmel,24c64";
+				reg = <0x54>;
+			};
+		};
+
+		i2c1mux0ch6: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x6>;
+
+			// Interposer IOEXP
+			io_expander5: gpio@27 {
+				compatible = "nxp,pca9554";
+				reg = <0x27>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				gpio-line-names =
+					"JTAG_MUX_SEL",
+					"IOX_BMC_RESET",
+					"RTC_CLR_L",
+					"RTC_U77_ALRT_N",
+					"",
+					"PSU_ALERT_N",
+					"",
+					"RST_P12V_STBY_N";
+			};
+		};
+
+		i2c1mux0ch7: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x7>;
+
+			// FIO TEMP SENSOR
+			temperature-sensor@4b {
+				compatible = "ti,tmp75";
+				reg = <0x4b>;
+			};
+
+			// FIO FRU EEPROM
+			eeprom@51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+		};
+	};
+};
+
+&i2c2 {
+	status = "okay";
+	// Module 0, Expander @0x20
+	io_expander0: gpio@20 {
+		compatible = "nxp,pca9555";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+			"FPGA_THERM_OVERT_L-I",
+			"FPGA_READY_BMC-I",
+			"HMC_BMC_DETECT-O",
+			"HMC_PGOOD-O",
+			"",
+			"BMC_STBY_CYCLE-O",
+			"FPGA_EROT_FATAL_ERROR_L-I",
+			"WP_HW_EXT_CTRL_L-O",
+			"EROT_FPGA_RST_L-O",
+			"FPGA_EROT_RECOVERY_L-O",
+			"BMC_EROT_FPGA_SPI_MUX_SEL-O",
+			"USB2_HUB_RST_L-O",
+			"",
+			"SGPIO_EN_L-O",
+			"B2B_IOEXP_INT_L-I",
+			"I2C_BUS_MUX_RESET_L-O";
+	};
+
+	// Module 1, Expander @0x21
+	io_expander1: gpio@21 {
+		compatible = "nxp,pca9555";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+			"SEC_FPGA_THERM_OVERT_L",
+			"SEC_FPGA_READY_BMC",
+			"SEC_HMC_BMC_DETECT",
+			"SEC_HMC_PGOOD",
+			"",
+			"SEC_BMC_SELF_POWER_CYCLE",
+			"SEC_SEC_FPGA_EROT_FATAL_ERROR_L",
+			"SEC_WP_HW_EXT_CTRL_L",
+			"SEC_EROT_FPGA_RST_L",
+			"SEC_FPGA_EROT_RECOVERY_L",
+			"SEC_BMC_EROT_FPGA_SPI_MUX_SEL",
+			"SEC_USB2_HUB_RST_L",
+			"",
+			"SEC_SGPIO_EN_L",
+			"SEC_IOB_IOEXP_INT_L",
+			"SEC_I2C_BUS_MUX_RESET_L";
+	};
+
+	// HMC Expander @0x27
+	io_expander2: gpio@27 {
+		compatible = "nxp,pca9555";
+		reg = <0x27>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+			"HMC_PRSNT_L-I",
+			"HMC_READY-I",
+			"HMC_EROT_FATAL_ERROR_L-I",
+			"I2C_MUX_SEL-O",
+			"HMC_EROT_SPI_MUX_SEL-O",
+			"HMC_EROT_RECOVERY_L-O",
+			"HMC_EROT_RST_L-O",
+			"GLOBAL_WP_HMC-O",
+			"FPGA_RST_L-O",
+			"USB2_HUB_RST-O",
+			"CPU_UART_MUX_SEL-O",
+			"",
+			"",
+			"",
+			"",
+			"";
+	};
+
+	// Module 0 Aux EEPROM
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	// Module 1 Aux EEPROM
+	eeprom@51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+	io_expander3: gpio@21 {
+		compatible = "nxp,pca9555";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+			"RTC_MUX_SEL",
+			"PCI_MUX_SEL",
+			"TPM_MUX_SEL",
+			"FAN_MUX-SEL",
+			"SGMII_MUX_SEL",
+			"DP_MUX_SEL",
+			"UPHY3_USB_SEL",
+			"NCSI_MUX_SEL",
+			"BMC_PHY_RST",
+			"RTC_CLR_L",
+			"BMC_12V_CTRL",
+			"PS_RUN_IO0_PG",
+			"",
+			"",
+			"",
+			"";
+	};
+
+	rtc@6f {
+		compatible = "nuvoton,nct3018y";
+		reg = <0x6f>;
+	};
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+	// SCM TEMP SENSOR BOARD
+	temperature-sensor@4b {
+		compatible = "national,lm75b";
+		reg = <0x4b>;
+	};
+
+	// SCM CPLD IOEXP
+	io_expander4: gpio@4f {
+		compatible = "nxp,pca9555";
+		reg = <0x4f>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+			"stby_power_en_cpld",
+			"stby_power_gd_cpld",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"";
+	};
+
+	// SCM FRU EEPROM
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	// BSM FRU EEPROM
+	eeprom@56 {
+		compatible = "atmel,24c64";
+		reg = <0x56>;
+	};
+};
+
+&i2c10 {
+	status = "okay";
+	multi-master;
+	mctp-controller;
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	// OCP NIC0 TEMP
+	temperature-sensor@1f {
+		compatible = "ti,tmp421";
+		reg = <0x1f>;
+	};
+
+	// OCP NIC0 FRU EEPROM
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+};
+
+&i2c11 {
+	status = "okay";
+
+	ssif-bmc@10 {
+		compatible = "ssif-bmc";
+		reg = <0x10>;
+	};
+};
+
+&i2c12 {
+	status = "okay";
+	multi-master;
+
+	// HPM 1 FRU EEPROM
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+	// CBC 2 FRU
+	eeprom@54 {
+		compatible = "atmel,24c02";
+		reg = <0x54>;
+	};
+	// CBC 3 FRU
+	eeprom@55 {
+		compatible = "atmel,24c02";
+		reg = <0x55>;
+	};
+};
+
+&i2c13 {
+	status = "okay";
+	multi-master;
+
+	// HPM FRU EEPROM
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	// CBC 0 FRU
+	eeprom@54 {
+		compatible = "atmel,24c02";
+		reg = <0x54>;
+	};
+
+	// CBC 1 FRU
+	eeprom@55 {
+		compatible = "atmel,24c02";
+		reg = <0x55>;
+	};
+
+	// HMC FRU EEPROM
+	eeprom@57 {
+		compatible = "atmel,24c02";
+		reg = <0x57>;
+	};
+};
+
+&i2c14 {
+	status = "okay";
+
+	// PDB CPLD IOEXP 0x10
+	io_expander9: gpio@10 {
+		compatible = "nxp,pca9555";
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
+		reg = <0x10>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+			"wSequence_Latch_State_N",
+			"wP12V_N1N2_RUNTIME_FLT_N",
+			"wP12V_FAN_RUNTIME_FLT_N",
+			"wP12V_AUX_RUNTIME_FLT_N",
+			"wHost_PERST_SEQPWR_FLT_N",
+			"wP12V_N1N2_SEQPWR_FLT_N",
+			"wP12V_FAN_SEQPWR_FLT_N",
+			"wP12V_AUX_SEQPWR_FLT_N",
+			"wP12V_RUNTIME_FLT_NIC1_N",
+			"wAUX_RUNTIME_FLT_NIC1_N",
+			"wP12V_SEQPWR_FLT_NIC1_N",
+			"wAUX_SEQPWR_FLT_NIC1_N",
+			"wP12V_RUNTIME_FLT_NIC0_N",
+			"wAUX_RUNTIME_FLT_NIC0_N",
+			"wP12V_SEQPWR_FLT_NIC0_N",
+			"wAUX_SEQPWR_FLT_NIC0_N";
+	};
+
+	// PDB CPLD IOEXP 0x11
+	io_expander10: gpio@11 {
+		compatible = "nxp,pca9555";
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
+		reg = <0x11>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+			"FM_P12V_NIC1_FLTB_R_N",
+			"FM_P3V3_NIC1_FAULT_R_N",
+			"FM_P12V_NIC0_FLTB_R_N",
+			"FM_P3V3_NIC0_FAULT_R_N",
+			"P48V_HS2_FAULT_N_PLD",
+			"P48V_HS1_FAULT_N_PLD",
+			"P12V_AUX_FAN_OC_PLD_N",
+			"P12V_AUX_FAN_FAULT_PLD_N",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"FM_SYS_THROTTLE_N",
+			"OCP_V3_2_PWRBRK_FROM_HOST_ISO_PLD_N",
+			"OCP_SFF_PWRBRK_FROM_HOST_ISO_PLD_N";
+	};
+
+	// PDB CPLD IOEXP 0x12
+	io_expander11: gpio@12 {
+		compatible = "nxp,pca9555";
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
+		reg = <0x12>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+			"P12V_AUX_PSU_SMB_ALERT_R_L",
+			"P12V_SCM_SENSE_ALERT_R_N",
+			"P12V_AUX_NIC1_SENSE_ALERT_R_N",
+			"P12V_AUX_NIC0_SENSE_ALERT_R_N",
+			"NODEB_PSU_SMB_ALERT_R_L",
+			"NODEA_PSU_SMB_ALERT_R_L",
+			"P12V_AUX_FAN_ALERT_PLD_N",
+			"P52V_SENSE_ALERT_PLD_N",
+			"PRSNT_RJ45_FIO_N_R",
+			"FM_MAIN_PWREN_RMC_EN_ISO_R",
+			"CHASSIS3_LEAK_Q_N_PLD",
+			"CHASSIS2_LEAK_Q_N_PLD",
+			"CHASSIS1_LEAK_Q_N_PLD",
+			"CHASSIS0_LEAK_Q_N_PLD",
+			"",
+			"SMB_RJ45_FIO_TMP_ALERT";
+	};
+
+	// PDB CPLD IOEXP 0x13
+	io_expander12: gpio@13 {
+		compatible = "nxp,pca9555";
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(I, 6) IRQ_TYPE_LEVEL_LOW>;
+		reg = <0x13>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+			"FAN_7_PRESENT_N",
+			"FAN_6_PRESENT_N",
+			"FAN_5_PRESENT_N",
+			"FAN_4_PRESENT_N",
+			"FAN_3_PRESENT_N",
+			"FAN_2_PRESENT_N",
+			"FAN_1_PRESENT_N",
+			"FAN_0_PRESENT_N",
+			"HP_LVC3_OCP_V3_2_PRSNT2_PLD_N",
+			"HP_LVC3_OCP_V3_1_PRSNT2_PLD_N",
+			"PRSNT_HDDBD_POWER_CABLE_N",
+			"PRSNT_OSFP0_POWER_CABLE_N",
+			"PRSNT_CHASSIS3_LEAK_CABLE_R_N",
+			"PRSNT_CHASSIS2_LEAK_CABLE_R_N",
+			"PRSNT_CHASSIS1_LEAK_CABLE_R_N",
+			"PRSNT_CHASSIS0_LEAK_CABLE_R_N";
+	};
+
+	// PDB CPLD IOEXP 0x14
+	io_expander13: gpio@14 {
+		compatible = "nxp,pca9555";
+		reg = <0x14>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+			"rmc_en_dc_pwr_on",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"leak_config_0",
+			"leak_config_1",
+			"leak_config_2",
+			"leak_config_3",
+			"mfg_led_test_mode_l",
+			"small_leak_err_inj",
+			"large_leak_err_inj",
+			"";
+	};
+};
+
+&i2c15 {
+	status = "okay";
+	multi-master;
+	mctp-controller;
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	// OCP NIC1 TEMP
+	temperature-sensor@1f {
+		compatible = "ti,tmp421";
+		reg = <0x1f>;
+	};
+
+	// OCP NIC1 FRU EEPROM
+	eeprom@52 {
+		compatible = "atmel,24c64";
+		reg = <0x52>;
+	};
+};
+
+&mac2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ncsi3_default>;
+	use-ncsi;
+};
+
+&mac3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ncsi4_default>;
+	use-ncsi;
+};
+
+&udma {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&wdt1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst1_default>;
+	aspeed,reset-type = "soc";
+	aspeed,external-signal;
+	aspeed,ext-push-pull;
+	aspeed,ext-active-high;
+	aspeed,ext-pulse-duration = <256>;
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-cmm.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-cmm.dts
index 90a3f485c67a..24153868cc00 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-cmm.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-cmm.dts
@@ -328,7 +328,7 @@
 &i2c1 {
 	status = "okay";
 
-	i2c-switch@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -341,7 +341,7 @@
 			#size-cells = <0>;
 			reg = <0>;
 
-			i2c-switch@70 {
+			i2c-mux@70 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -390,7 +390,7 @@
 				};
 			};
 
-			i2c-switch@73 {
+			i2c-mux@73 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -446,7 +446,7 @@
 			#size-cells = <0>;
 			reg = <1>;
 
-			i2c-switch@70 {
+			i2c-mux@70 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -495,7 +495,7 @@
 				};
 			};
 
-			i2c-switch@73 {
+			i2c-mux@73 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -551,7 +551,7 @@
 			#size-cells = <0>;
 			reg = <2>;
 
-			i2c-switch@70 {
+			i2c-mux@70 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -600,7 +600,7 @@
 				};
 			};
 
-			i2c-switch@73 {
+			i2c-mux@73 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -656,7 +656,7 @@
 			#size-cells = <0>;
 			reg = <3>;
 
-			i2c-switch@70 {
+			i2c-mux@70 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -705,7 +705,7 @@
 				};
 			};
 
-			i2c-switch@73 {
+			i2c-mux@73 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -761,7 +761,7 @@
 			#size-cells = <0>;
 			reg = <4>;
 
-			i2c-switch@70 {
+			i2c-mux@70 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -810,7 +810,7 @@
 				};
 			};
 
-			i2c-switch@73 {
+			i2c-mux@73 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -866,7 +866,7 @@
 			#size-cells = <0>;
 			reg = <5>;
 
-			i2c-switch@70 {
+			i2c-mux@70 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -915,7 +915,7 @@
 				};
 			};
 
-			i2c-switch@73 {
+			i2c-mux@73 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -971,7 +971,7 @@
 			#size-cells = <0>;
 			reg = <6>;
 
-			i2c-switch@70 {
+			i2c-mux@70 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1020,7 +1020,7 @@
 				};
 			};
 
-			i2c-switch@73 {
+			i2c-mux@73 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1076,7 +1076,7 @@
 			#size-cells = <0>;
 			reg = <7>;
 
-			i2c-switch@70 {
+			i2c-mux@70 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1125,7 +1125,7 @@
 				};
 			};
 
-			i2c-switch@73 {
+			i2c-mux@73 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1183,7 +1183,7 @@
 &i2c2 {
 	status = "okay";
 
-	i2c-switch@71 {
+	i2c-mux@71 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -1281,7 +1281,7 @@
 &i2c8 {
 	status = "okay";
 
-	i2c-switch@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -1294,7 +1294,7 @@
 			#size-cells = <0>;
 			reg = <0>;
 
-			i2c-switch@70 {
+			i2c-mux@70 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1350,7 +1350,7 @@
 			#size-cells = <0>;
 			reg = <1>;
 
-			i2c-switch@70 {
+			i2c-mux@70 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1406,7 +1406,7 @@
 			#size-cells = <0>;
 			reg = <2>;
 
-			i2c-switch@70 {
+			i2c-mux@70 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1462,7 +1462,7 @@
 			#size-cells = <0>;
 			reg = <3>;
 
-			i2c-switch@70 {
+			i2c-mux@70 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-darwin.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-darwin.dts
new file mode 100644
index 000000000000..58c107a1b6cf
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-darwin.dts
@@ -0,0 +1,72 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2021 Facebook Inc.
+
+/dts-v1/;
+
+#include "ast2600-facebook-netbmc-common.dtsi"
+
+/ {
+	model = "Facebook Darwin BMC";
+	compatible = "facebook,darwin-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial0 = &uart5;
+		serial1 = &uart1;
+		serial2 = &uart2;
+		serial3 = &uart3;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+			      <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+			      <&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>,
+			      <&adc1 4>, <&adc1 5>, <&adc1 6>, <&adc1 7>;
+	};
+
+	spi_gpio: spi {
+		num-chipselects = <1>;
+		cs-gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>;
+	};
+};
+
+&i2c0 {
+	eeprom@50 {
+		compatible = "atmel,24c512";
+		reg = <0x50>;
+	};
+};
+
+&adc0 {
+	status = "okay";
+
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+		     &pinctrl_adc2_default &pinctrl_adc3_default
+		     &pinctrl_adc4_default &pinctrl_adc5_default
+		     &pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+	status = "okay";
+
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+		     &pinctrl_adc10_default &pinctrl_adc11_default
+		     &pinctrl_adc12_default &pinctrl_adc13_default
+		     &pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&emmc {
+	status = "okay";
+
+	non-removable;
+	max-frequency = <25000000>;
+	bus-width = <4>;
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-elbert.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-elbert.dts
index 27b43fe099f1..ff1009ea1c49 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-elbert.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-elbert.dts
@@ -44,7 +44,7 @@
 		stdout-path = &uart5;
 	};
 
-	spi_gpio: spi-gpio {
+	spi_gpio: spi {
 		num-chipselects = <1>;
 		cs-gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>;
 	};
@@ -65,7 +65,7 @@
 };
 
 &i2c2 {
-	i2c-switch@75 {
+	i2c-mux@75 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -123,7 +123,7 @@
 };
 
 &i2c5 {
-	i2c-switch@75 {
+	i2c-mux@75 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -183,3 +183,33 @@
 &i2c11 {
 	status = "okay";
 };
+
+/*
+ * BMC's "mac3" controller is connected to BCM53134P's IMP_RGMII port
+ * directly (fixed link, no PHY in between).
+ * Note: BMC's "mdio0" controller is connected to BCM53134P's MDIO
+ * interface, and the MDIO channel will be enabled in dts later, when
+ * BCM53134 is added to "bcm53xx" DSA driver.
+ */
+&mac3 {
+	status = "okay";
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii4_default>;
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&emmc {
+	status = "okay";
+
+	non-removable;
+	max-frequency = <25000000>;
+	bus-width = <4>;
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-fuji.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-fuji-data64.dts
index af58a73bbc49..aa9576d8ab56 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-fuji.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-fuji-data64.dts
@@ -7,8 +7,8 @@
 #include "ast2600-facebook-netbmc-common.dtsi"
 
 / {
-	model = "Facebook Fuji BMC";
-	compatible = "facebook,fuji-bmc", "aspeed,ast2600";
+	model = "Facebook Fuji BMC (64MB Datastore)";
+	compatible = "facebook,fuji-data64-bmc", "aspeed,ast2600";
 
 	aliases {
 		/*
@@ -207,7 +207,7 @@
 		i2c143 = &imux143;
 	};
 
-	spi_gpio: spi-gpio {
+	spi_gpio: spi {
 		num-chipselects = <3>;
 		cs-gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>,
 			   <0>,	/* device reg=<1> does not exist */
@@ -223,6 +223,13 @@
 	};
 };
 
+&fmc {
+	flash@0 {
+		/delete-node/partitions;
+#include "facebook-bmc-flash-layout-128-data64.dtsi"
+	};
+};
+
 &i2c0 {
 	multi-master;
 	bus-frequency = <1000000>;
@@ -233,7 +240,7 @@
 	 * PCA9548 (2-0070) provides 8 channels connecting to SCM (System
 	 * Controller Module).
 	 */
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -248,8 +255,6 @@
 			adm1278@10 {
 				compatible = "adi,adm1278";
 				reg = <0x10>;
-				#address-cells = <1>;
-				#size-cells = <0>;
 				shunt-resistor-micro-ohms = <1500>;
 			};
 		};
@@ -303,7 +308,7 @@
 	 * PCA9548 (8-0070) provides 8 channels connecting to SMB (Switch
 	 * Main Board).
 	 */
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -315,7 +320,7 @@
 			#size-cells = <0>;
 			reg = <0>;
 
-			i2c-switch@71 {
+			i2c-mux@71 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -481,7 +486,7 @@
 			#size-cells = <0>;
 			reg = <1>;
 
-			i2c-switch@72 {
+			i2c-mux@72 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -544,7 +549,7 @@
 			#size-cells = <0>;
 			reg = <2>;
 
-			i2c-switch@76 {
+			i2c-mux@76 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -577,8 +582,6 @@
 					adm1278@10 {
 						compatible = "adi,adm1278";
 						reg = <0x10>;
-						#address-cells = <1>;
-						#size-cells = <0>;
 						shunt-resistor-micro-ohms = <250>;
 					};
 				};
@@ -615,7 +618,7 @@
 			#size-cells = <0>;
 			reg = <3>;
 
-			i2c-switch@76 {
+			i2c-mux@76 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -648,8 +651,6 @@
 					adm1278@10 {
 						compatible = "adi,adm1278";
 						reg = <0x10>;
-						#address-cells = <1>;
-						#size-cells = <0>;
 						shunt-resistor-micro-ohms = <250>;
 					};
 				};
@@ -715,7 +716,7 @@
 	 * PCA9548 (11-0077) provides 8 channels connecting to SMB (Switch
 	 * Main Board).
 	 */
-	i2c-switch@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -727,7 +728,7 @@
 			#size-cells = <0>;
 			reg = <0>;
 
-			i2c-switch@76 {
+			i2c-mux@76 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -790,7 +791,7 @@
 			#size-cells = <0>;
 			reg = <1>;
 
-			i2c-switch@76 {
+			i2c-mux@76 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -853,7 +854,7 @@
 			#size-cells = <0>;
 			reg = <2>;
 
-			i2c-switch@76 {
+			i2c-mux@76 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -916,7 +917,7 @@
 			#size-cells = <0>;
 			reg = <3>;
 
-			i2c-switch@76 {
+			i2c-mux@76 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -979,7 +980,7 @@
 			#size-cells = <0>;
 			reg = <4>;
 
-			i2c-switch@76 {
+			i2c-mux@76 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1042,7 +1043,7 @@
 			#size-cells = <0>;
 			reg = <5>;
 
-			i2c-switch@76 {
+			i2c-mux@76 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1105,7 +1106,7 @@
 			#size-cells = <0>;
 			reg = <6>;
 
-			i2c-switch@76 {
+			i2c-mux@76 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1168,7 +1169,7 @@
 			#size-cells = <0>;
 			reg = <7>;
 
-			i2c-switch@76 {
+			i2c-mux@76 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1242,10 +1243,14 @@
 	};
 };
 
-&mac3 {
+&emmc_controller {
+	status = "okay";
+};
+
+&emmc {
 	status = "okay";
-	phy-mode = "rgmii";
-	phy-handle = <&ethphy3>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_rgmii4_default>;
+
+	non-removable;
+	max-frequency = <25000000>;
+	bus-width = <4>;
 };
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-fuji.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-fuji.dts
new file mode 100644
index 000000000000..5dc2a165e441
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-fuji.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2020 Facebook Inc.
+
+#include "aspeed-bmc-facebook-fuji-data64.dts"
+
+/ {
+	model = "Facebook Fuji BMC";
+	compatible = "facebook,fuji-bmc", "aspeed,ast2600";
+};
+
+&fmc {
+	flash@0 {
+		/delete-node/partitions;
+#include "facebook-bmc-flash-layout-128.dtsi"
+	};
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-galaxy100.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-galaxy100.dts
index 60e875ac2461..60e875ac2461 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-galaxy100.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-galaxy100.dts
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-greatlakes.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-greatlakes.dts
new file mode 100644
index 000000000000..49914a4a179f
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-greatlakes.dts
@@ -0,0 +1,292 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2022 Facebook Inc.
+
+/dts-v1/;
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/leds/leds-pca955x.h>
+#include <dt-bindings/i2c/i2c.h>
+
+/ {
+	model = "Facebook Greatlakes BMC";
+	compatible = "facebook,greatlakes-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial4 = &uart5;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+				<&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+				<&adc1 0>, <&adc1 2>, <&adc1 3>, <&adc1 4>,
+				<&adc1 5>, <&adc1 6>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&wdt1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst1_default>;
+	aspeed,reset-type = "soc";
+	aspeed,external-signal;
+	aspeed,ext-push-pull;
+	aspeed,ext-active-high;
+	aspeed,ext-pulse-duration = <256>;
+};
+
+&mac3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+	no-hw-checksum;
+	use-ncsi;
+	mellanox,multi-host;
+	ncsi-ctrl,start-redo-probe;
+	ncsi-ctrl,no-channel-monitor;
+	ncsi-package = <1>;
+	ncsi-channel = <1>;
+	ncsi-rexmit = <1>;
+	ncsi-timeout = <2>;
+};
+
+&rtc {
+	status = "okay";
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64.dtsi"
+	};
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc2";
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+	multi-master;
+	ipmb@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	multi-master;
+	ipmb@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+	multi-master;
+	ipmb@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+	multi-master;
+	ipmb@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+	mctp-controller;
+	temperature-sensor@1f {
+		compatible = "ti,tmp421";
+		reg = <0x1f>;
+	};
+	// NIC EEPROM
+	eeprom@50 {
+		compatible = "st,24c32";
+		reg = <0x50>;
+	};
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+};
+
+&i2c9 {
+	status = "okay";
+	multi-master;
+	ipmb@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+	eeprom@51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+	};
+	eeprom@54 {
+		compatible = "atmel,24c128";
+		reg = <0x54>;
+	};
+};
+
+&i2c12 {
+	status = "okay";
+	temperature-sensor@4f {
+		compatible = "national,lm75";
+		reg = <0x4f>;
+	};
+};
+
+&i2c13 {
+	status = "okay";
+};
+
+&adc0 {
+	status = "okay";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+			&pinctrl_adc2_default &pinctrl_adc3_default
+			&pinctrl_adc4_default &pinctrl_adc5_default
+			&pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+	status = "okay";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc10_default
+			&pinctrl_adc11_default &pinctrl_adc12_default
+			&pinctrl_adc13_default &pinctrl_adc14_default>;
+};
+
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&uhci {
+	status = "okay";
+};
+
+&gpio0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpiu1_default &pinctrl_gpiu7_default>;
+
+	gpio-line-names =
+	/*A0-A7*/ "","","","","","","","",
+	/*B0-B7*/ "power-bmc-nic","presence-ocp-debug",
+		  "power-bmc-slot1","power-bmc-slot2",
+		  "power-bmc-slot3","power-bmc-slot4","","",
+	/*C0-C7*/ "presence-ocp-nic","","","reset-cause-nic-primary",
+		  "reset-cause-nic-secondary","","","",
+	/*D0-D7*/ "","","","","","","","",
+	/*E0-E7*/ "","","","","","","","",
+	/*F0-F7*/ "slot1-bmc-reset-button","slot2-bmc-reset-button",
+		  "slot3-bmc-reset-button","slot4-bmc-reset-button",
+		  "","","","presence-emmc",
+	/*G0-G7*/ "","","","","","","","",
+	/*H0-H7*/ "","","","",
+		  "presence-mb-slot1","presence-mb-slot2",
+		  "presence-mb-slot3","presence-mb-slot4",
+	/*I0-I7*/ "","","","","","","bb-bmc-button","",
+	/*J0-J7*/ "","","","","","","","",
+	/*K0-K7*/ "","","","","","","","",
+	/*L0-L7*/ "","","","","","","","",
+	/*M0-M7*/ "","power-nic-bmc-enable","","usb-bmc-enable","","reset-cause-usb-hub","","",
+	/*N0-N7*/ "","","","","bmc-ready","","","",
+	/*O0-O7*/ "","","","","","","fan0-bmc-cpld-enable","fan1-bmc-cpld-enable",
+	/*P0-P7*/ "fan2-bmc-cpld-enable","fan3-bmc-cpld-enable",
+		  "reset-cause-pcie-slot1","reset-cause-pcie-slot2",
+		  "reset-cause-pcie-slot3","reset-cause-pcie-slot4","","",
+	/*Q0-Q7*/ "","","","","","","","",
+	/*R0-R7*/ "","","","","","","","",
+	/*S0-S7*/ "","","power-p5v-usb","presence-bmc-tpm","","","","",
+	/*T0-T7*/ "","","","","","","","",
+	/*U0-U7*/ "","","","","","","","GND",
+	/*V0-V7*/ "bmc-slot1-ac-button","bmc-slot2-ac-button",
+		  "bmc-slot3-ac-button","bmc-slot4-ac-button",
+		  "","","","",
+	/*W0-W7*/ "","","","","","","","",
+	/*X0-X7*/ "","","","","","","","",
+	/*Y0-Y7*/ "","","","reset-cause-emmc","","","","",
+	/*Z0-Z7*/ "","","","","","","","";
+};
+
+&gpio1 {
+	gpio-line-names =
+	/*18A0-18A7*/ "","","","","","","","",
+	/*18B0-18B7*/ "","","","","","","","",
+	/*18C0-18C7*/ "","","","","","","","",
+	/*18D0-18D7*/ "","","","","","","","",
+	/*18E0-18E3*/ "","","","","","","","";
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-harma.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-harma.dts
new file mode 100644
index 000000000000..b733efe31e8d
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-harma.dts
@@ -0,0 +1,822 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2023 Facebook Inc.
+
+/dts-v1/;
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
+
+/ {
+	model = "Facebook Harma";
+	compatible = "facebook,harma-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart4;
+		serial4 = &uart5;
+
+		i2c20 = &imux20;
+		i2c21 = &imux21;
+		i2c22 = &imux22;
+		i2c23 = &imux23;
+		i2c28 = &imux28;
+		i2c29 = &imux29;
+		i2c30 = &imux30;
+		i2c31 = &imux31;
+
+		spi1 = &spi_gpio;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+			      <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+			      <&adc1 2>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "bmc_heartbeat_amber";
+			gpios = <&gpio0 ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-1 {
+			label = "fp_id_amber";
+			default-state = "off";
+			gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-2 {
+			label = "power_blue";
+			default-state = "off";
+			gpios = <&gpio0 124 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	spi_gpio: spi {
+		status = "okay";
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sck-gpios = <&gpio0 ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio0 ASPEED_GPIO(Z, 4) GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpio0 ASPEED_GPIO(Z, 5) GPIO_ACTIVE_HIGH>;
+		num-chipselects = <1>;
+		cs-gpios = <&gpio0 ASPEED_GPIO(Z, 0) GPIO_ACTIVE_LOW>;
+
+		tpm@0 {
+			compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
+			spi-max-frequency = <33000000>;
+			reg = <0>;
+		};
+	};
+};
+
+// HOST BIOS Debug
+&uart1 {
+	status = "okay";
+};
+
+// SOL Host Console
+&uart2 {
+	status = "okay";
+	pinctrl-0 = <>;
+};
+
+// SOL BMC Console
+&uart4 {
+	status = "okay";
+	pinctrl-0 = <>;
+};
+
+// BMC Debug Console
+&uart5 {
+	status = "okay";
+};
+
+// MTIA
+&uart6 {
+	status = "okay";
+};
+
+&uart_routing {
+	status = "okay";
+};
+
+&wdt1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst1_default>;
+	aspeed,reset-type = "soc";
+	aspeed,external-signal;
+	aspeed,ext-push-pull;
+	aspeed,ext-active-high;
+	aspeed,ext-pulse-duration = <256>;
+};
+
+&mac3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+	use-ncsi;
+};
+
+&fmc {
+	status = "okay";
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-128.dtsi"
+	};
+
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "alt-bmc";
+		spi-max-frequency = <50000000>;
+	};
+};
+
+// BIOS Flash
+&spi2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi2_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "pnor";
+		spi-max-frequency = <12000000>;
+		spi-tx-bus-width = <2>;
+		spi-rx-bus-width = <2>;
+	};
+};
+
+&kcs2 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca8>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+};
+
+&i2c0 {
+	status = "okay";
+
+	pwm@5e {
+		compatible = "maxim,max31790";
+		reg = <0x5e>;
+	};
+
+	power-sensor@40 {
+		compatible = "ti,ina238";
+		reg = <0x40>;
+		shunt-resistor = <1000>;
+	};
+
+	power-sensor@41 {
+		compatible = "ti,ina238";
+		reg = <0x41>;
+		shunt-resistor = <1000>;
+	};
+
+	power-sensor@44 {
+		compatible = "ti,ina238";
+		reg = <0x44>;
+		shunt-resistor = <1000>;
+	};
+
+	power-sensor@45 {
+		compatible = "ti,ina238";
+		reg = <0x45>;
+		shunt-resistor = <1000>;
+	};
+
+	temperature-sensor@4b {
+		compatible = "ti,tmp75";
+		reg = <0x4b>;
+	};
+
+	gpio@12 {
+		compatible = "nxp,pca9555";
+		reg = <0x12>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&sgpiom0>;
+		interrupts = <116 IRQ_TYPE_LEVEL_LOW>;
+
+		gpio-line-names =
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","fcb2-activate",
+		"","";
+	};
+};
+
+&i2c1 {
+	status = "okay";
+
+	temperature-sensor@4b {
+		compatible = "ti,tmp75";
+		reg = <0x4b>;
+	};
+
+	// MB NIC FRU
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	pwm@5e {
+		compatible = "maxim,max31790";
+		reg = <0x5e>;
+	};
+
+	power-sensor@40 {
+		compatible = "ti,ina238";
+		reg = <0x40>;
+		shunt-resistor = <1000>;
+	};
+
+	power-sensor@41 {
+		compatible = "ti,ina238";
+		reg = <0x41>;
+		shunt-resistor = <1000>;
+	};
+
+	power-sensor@44 {
+		compatible = "ti,ina238";
+		reg = <0x44>;
+		shunt-resistor = <1000>;
+	};
+
+	power-sensor@45 {
+		compatible = "ti,ina238";
+		reg = <0x45>;
+		shunt-resistor = <1000>;
+	};
+
+	temperature-sensor@4b {
+		compatible = "ti,tmp75";
+		reg = <0x4b>;
+	};
+
+	gpio@12 {
+		compatible = "nxp,pca9555";
+		reg = <0x12>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&sgpiom0>;
+		interrupts = <114 IRQ_TYPE_LEVEL_LOW>;
+
+		gpio-line-names =
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","fcb1-activate",
+		"","";
+	};
+};
+
+&i2c3 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9543";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		imux20: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			//Retimer Flash
+			eeprom@50 {
+				compatible = "atmel,24c2048";
+				reg = <0x50>;
+				pagesize = <128>;
+			};
+		};
+		imux21: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			retimer@24 {
+				compatible = "asteralabs,pt5161l";
+				reg = <0x24>;
+			};
+		};
+	};
+};
+
+&i2c4 {
+	status = "okay";
+	// PDB FRU
+	eeprom@52 {
+		compatible = "atmel,24c64";
+		reg = <0x52>;
+	};
+
+	power-monitor@69 {
+		compatible = "pmbus";
+		reg = <0x69>;
+	};
+
+	temperature-sensor@49 {
+		compatible = "ti,tmp75";
+		reg = <0x49>;
+	};
+
+	power-monitor@44 {
+		compatible = "lltc,ltc4287";
+		reg = <0x44>;
+		shunt-resistor-micro-ohms = <250>;
+	};
+
+	power-monitor@40 {
+		compatible = "infineon,xdp710";
+		reg = <0x40>;
+	};
+
+	power-sensor@45 {
+		compatible = "ti,ina238";
+		reg = <0x45>;
+		shunt-resistor = <500>;
+	};
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9543";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		imux22: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			power-monitor@45 {
+				compatible = "ti,ina230";
+				reg = <0x45>;
+			};
+
+		};
+		imux23: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			power-monitor@45 {
+				compatible = "ti,ina230";
+				reg = <0x45>;
+			};
+		};
+	};
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+
+	mctp-controller;
+	multi-master;
+
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	gpio@30 {
+		compatible = "nxp,pca9555";
+		reg = <0x30>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+	gpio@31 {
+		compatible = "nxp,pca9555";
+		reg = <0x31>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	// PTTV FRU
+	eeprom@52 {
+		compatible = "atmel,24c64";
+		reg = <0x52>;
+	};
+};
+
+&i2c11 {
+	status = "okay";
+
+	gpio@13 {
+		compatible = "nxp,pca9555";
+		reg = <0x13>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&sgpiom0>;
+		interrupts = <222 IRQ_TYPE_LEVEL_LOW>;
+
+		gpio-line-names =
+		"","",
+		"","",
+		"","",
+		"","health-mmc",
+		"","",
+		"","",
+		"","",
+		"","";
+	};
+
+	gpio@30 {
+		compatible = "nxp,pca9555";
+		reg = <0x30>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+	gpio@31 {
+		compatible = "nxp,pca9555";
+		reg = <0x31>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	// Aegis FRU
+	eeprom@52 {
+		compatible = "atmel,24c64";
+		reg = <0x52>;
+	};
+};
+
+&i2c12 {
+	status = "okay";
+	retimer@24 {
+		compatible = "asteralabs,pt5161l";
+		reg = <0x24>;
+	};
+};
+
+&i2c13 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9545";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		imux28: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			power-sensor@20 {
+				compatible = "mps,mp5990";
+				reg = <0x20>;
+			};
+			power-monitor@61 {
+				compatible = "isil,isl69260";
+				reg = <0x61>;
+			};
+			power-monitor@62 {
+				compatible = "isil,isl69260";
+				reg = <0x62>;
+			};
+			power-monitor@63 {
+				compatible = "isil,isl69260";
+				reg = <0x63>;
+			};
+			power-monitor@64 {
+				compatible = "infineon,xdpe152c4";
+				reg = <0x64>;
+			};
+			power-monitor@66 {
+				compatible = "infineon,xdpe152c4";
+				reg = <0x66>;
+			};
+			power-monitor@68 {
+				compatible = "infineon,xdpe152c4";
+				reg = <0x68>;
+			};
+		};
+		imux29: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			//MB FRU
+			eeprom@54 {
+				compatible = "atmel,24c64";
+				reg = <0x54>;
+			};
+
+			adc@1d {
+				compatible = "ti,adc128d818";
+				reg = <0x1d>;
+				ti,mode = /bits/ 8 <1>;
+			};
+
+			adc@1f {
+				compatible = "ti,adc128d818";
+				reg = <0x1f>;
+				ti,mode = /bits/ 8 <1>;
+			};
+
+		};
+		imux30: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+		imux31: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			rtc@51 {
+				compatible = "nxp,pcf8563";
+				reg = <0x51>;
+			};
+		};
+	};
+};
+
+// To Debug card
+&i2c14 {
+	status = "okay";
+	multi-master;
+
+	ipmb@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
+};
+
+&i2c15 {
+	status = "okay";
+
+	// SCM FRU
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	// BSM FRU
+	eeprom@56 {
+		compatible = "atmel,24c64";
+		reg = <0x56>;
+	};
+};
+
+&adc0 {
+	aspeed,int-vref-microvolt = <2500000>;
+	status = "okay";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+		&pinctrl_adc2_default &pinctrl_adc3_default
+		&pinctrl_adc4_default &pinctrl_adc5_default
+		&pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+	aspeed,int-vref-microvolt = <2500000>;
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc10_default>;
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&gpio0 {
+	pinctrl-names = "default";
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","","","",
+	/*B0-B7*/	"","","","",
+			"bmc-spi-mux-select-0","led-identify","","",
+	/*C0-C7*/	"reset-cause-platrst","","","","",
+			"power-hsc-good","power-chassis-good","",
+	/*D0-D7*/	"","","sol-uart-select","","","","","",
+	/*E0-E7*/	"","","","","","","","",
+	/*F0-F7*/	"","","","","","","","",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"","","","","","","","",
+	/*I0-I7*/	"","","","","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","",
+			"leakage-detect-alert","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"led-postcode-0","led-postcode-1",
+			"led-postcode-2","led-postcode-3",
+			"led-postcode-4","led-postcode-5",
+			"led-postcode-6","led-postcode-7",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"power-button","power-host-control",
+			"reset-button","","led-power","","","",
+	/*Q0-Q7*/
+			"","","","",
+			"","power-chassis-control","","uart-switch-button",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","","","","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","led-identify-gate","",
+	/*V0-V7*/	"","","","",
+			"","",
+			"","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"","","","","","","presence-post-card","";
+};
+
+&gpio1 {
+	gpio-line-names =
+	/*18A0-18A7*/ "ac-power-button","","","","","","","",
+	/*18B0-18B7*/ "","","","","","","","",
+	/*18C0-18C7*/ "","","","","","","","",
+	/*18D0-18D7*/ "","","","","","","","",
+	/*18E0-18E3*/ "","","","","","","","";
+};
+
+&sgpiom0 {
+	status = "okay";
+	ngpios = <128>;
+	bus-frequency = <2000000>;
+	gpio-line-names =
+	/*in - out - in - out */
+	/*A0-A3 line 0-7*/
+	"presence-scm-cable","power-config-disable-e1s-0",
+	"","",
+	"","power-config-disable-e1s-1",
+	"","",
+	/*A4-A7 line 8-15*/
+	"","power-config-asic-module-enable",
+	"power-p3v3-standby","power-config-asic-power-good",
+	"power-p1v8-good","power-config-pdb-power-good",
+	"presence-cpu","smi-control-n",
+	/*B0-B3 line 16-23*/
+	"","nmi-control-n",
+	"power-pvdd33-s5","nmi-control-sync-flood-n",
+	"","",
+	"power-pvdd18-s5","",
+	/*B4-B7 line 24-31*/
+	"","FM_CPU_SP5R1",
+	"reset-cause-rsmrst","FM_CPU_SP5R2",
+	"","FM_CPU_SP5R3",
+	"","FM_CPU_SP5R4",
+	/*C0-C3 line 32-39*/
+	"","FM_CPU0_SA0",
+	"","FM_CPU0_SA1",
+	"","rt-cpu0-p0-enable",
+	"","rt-cpu0-p1-enable",
+	/*C4-C7 line 40-47*/
+	"","smb-rt-rom-p0-select",
+	"","smb-rt-rom-p1-select",
+	"","i3c-cpu-mux0-oe-n",
+	"","i3c-cpu-mux0-select",
+	/*D0-D3 line 48-55*/
+	"","i3c-cpu-mux1-oe-n",
+	"","i3c-cpu-mux1-select",
+	"","reset-control-bmc",
+	"","reset-control-cpu0-p0-mux",
+	/*D4-D7 line 56-63*/
+	"","reset-control-cpu0-p1-mux",
+	"","reset-control-e1s-mux",
+	"power-host-good","reset-control-mb-mux",
+	"host0-ready","reset-control-smb-e1s-0",
+	/*E0-E3 line 64-71*/
+	"","reset-control-smb-e1s-1",
+	"post-end-n","reset-control-srst",
+	"presence-e1s-0","reset-control-usb-hub",
+	"","reset-control",
+	/*E4-E7 line 72-79*/
+	"presence-e1s-1","reset-control-cpu-kbrst",
+	"","reset-control-platrst",
+	"","bmc-jtag-mux-select-0",
+	"","bmc-jtag-mux-select-1",
+	/*F0-F3 line 80-87*/
+	"","bmc-jtag-select",
+	"","bmc-ready-n",
+	"","bmc-ready-sgpio",
+	"","rt-cpu0-p0-force-enable",
+	/*F4-F7 line 88-95*/
+	"presence-asic-modules-0","rt-cpu0-p1-force-enable",
+	"presence-asic-modules-1","bios-debug-msg-disable",
+	"power-asic-good","uart-control-buffer-select",
+	"presence-cmm","ac-control-n",
+	/*G0-G3 line 96-103*/
+	"FM_CPU_CORETYPE2","",
+	"FM_CPU_CORETYPE1","rtc-battery-voltage-read-enable",
+	"FM_CPU_CORETYPE0","",
+	"FM_BOARD_REV_ID5","",
+	/*G4-G7 line 104-111*/
+	"FM_BOARD_REV_ID4","",
+	"FM_BOARD_REV_ID3","",
+	"FM_BOARD_REV_ID2","",
+	"FM_BOARD_REV_ID1","",
+	/*H0-H3 line 112-119*/
+	"FM_BOARD_REV_ID0","reset-control-cmos-clear",
+	"","","","","","",
+	/*H4-H7 line 120-127*/
+	"","",
+	"reset-control-pcie-expansion-3","",
+	"reset-control-pcie-expansion-2","",
+	"reset-control-pcie-expansion-1","",
+	/*I0-I3 line 128-135*/
+	"reset-control-pcie-expansion-0","",
+	"FM_EXP_SLOT_ID1","",
+	"FM_EXP_SLOT_ID0","",
+	"","",
+	/*I4-I7 line 136-143*/
+	"","","","","","","","",
+	/*J0-J3 line 144-151*/
+	"","","power-card-enable","","","","","",
+	/*J4-J7 line 152-159*/
+	"SLOT_ID_BCB_0","",
+	"SLOT_ID_BCB_1","",
+	"SLOT_ID_BCB_2","",
+	"SLOT_ID_BCB_3","",
+	/*K0-K3 line 160-167*/
+	"","","","","","","P0_I3C_APML_ALERT_L","",
+	/*K4-K7 line 168-175*/
+	"","","","","","","irq-uv-detect-alert","",
+	/*L0-L3 line 176-183*/
+	"irq-hsc-alert","",
+	"cpu0-prochot-alert","",
+	"cpu0-thermtrip-alert","",
+	"reset-cause-pcie","",
+	/*L4-L7 line 184-191*/
+	"pvdd11-ocp-alert","",
+	"power-fault-n","",
+	"asic0-card-type-detection0-n","",
+	"asic0-card-type-detection1-n","",
+	/*M0-M3 line 192-199*/
+	"asic0-card-type-detection2-n","",
+	"uart-switch-lsb","",
+	"uart-switch-msb","",
+	"power-12v-memory-good","",
+	/*M4-M7 line 200-207*/
+	"","","","","","","","",
+	/*N0-N3 line 208-215*/
+	"","","","","","","","",
+	/*N4-N7 line 216-223*/
+	"","","","","","","","",
+	/*O0-O3 line 224-231*/
+	"","",
+	"irq-pvddcore0-ocp-alert","",
+	"irq-pvddcore1-ocp-alert","",
+	"","",
+	/*O4-O7 line 232-239*/
+	"","","","","","","","",
+	/*P0-P3 line 240-247*/
+	"","","","","","","","",
+	/*P4-P7 line 248-255*/
+	"","","","","","","","";
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts
new file mode 100644
index 000000000000..eb8d4b95596c
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minerva.dts
@@ -0,0 +1,1619 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2023 Facebook Inc.
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
+
+/ {
+	model = "Facebook Minerva CMM";
+	compatible = "facebook,minerva-cmc", "aspeed,ast2600";
+
+	aliases {
+		serial4 = &uart5;
+		serial5 = &uart6;
+		/*
+		 * PCA9548 (2-0077) provides 8 channels connecting to
+		 * 6 pcs of FCB (Fan Controller Board).
+		 */
+		i2c16 = &imux16;
+		i2c17 = &imux17;
+		i2c18 = &imux18;
+		i2c19 = &imux19;
+		i2c20 = &imux20;
+		i2c21 = &imux21;
+		i2c22 = &imux22;
+		i2c23 = &imux23;
+		i2c24 = &imux24;
+		i2c25 = &imux25;
+		i2c26 = &imux26;
+		i2c27 = &imux27;
+		i2c28 = &imux28;
+		i2c29 = &imux29;
+		i2c30 = &imux30;
+		i2c31 = &imux31;
+		i2c32 = &imux32;
+		i2c33 = &imux33;
+		i2c34 = &imux34;
+		i2c35 = &imux35;
+		i2c36 = &imux36;
+		i2c37 = &imux37;
+		i2c38 = &imux38;
+		i2c39 = &imux39;
+		i2c40 = &imux40;
+		i2c41 = &imux41;
+		i2c42 = &imux42;
+		i2c43 = &imux43;
+		i2c44 = &imux44;
+		i2c45 = &imux45;
+		i2c46 = &imux46;
+		i2c47 = &imux47;
+
+		spi1 = &spi_gpio;
+	};
+
+	chosen {
+		stdout-path = "serial5:57600n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+			<&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+			<&adc1 2>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "bmc_heartbeat_amber";
+			gpios = <&gpio0 ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-1 {
+			label = "fp_id_amber";
+			default-state = "off";
+			gpios = <&gpio0 ASPEED_GPIO(B, 5) GPIO_ACTIVE_HIGH>;
+		};
+
+		led-2 {
+			label = "power_blue";
+			default-state = "off";
+			gpios = <&gpio0 ASPEED_GPIO(P, 4) GPIO_ACTIVE_HIGH>;
+		};
+
+		led-3 {
+			label = "fan_status_led";
+			gpios = <&leds_gpio 9 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-4 {
+			label = "fan_fault_led_n";
+			gpios = <&leds_gpio 10 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-5 {
+			label = "bmc_ready_noled";
+			gpios = <&sgpiom0 141 (GPIO_ACTIVE_HIGH|GPIO_TRANSITORY)>;
+		};
+	};
+
+	spi_gpio: spi {
+		status = "okay";
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sck-gpios = <&gpio0 ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio0 ASPEED_GPIO(Z, 4) GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpio0 ASPEED_GPIO(Z, 5) GPIO_ACTIVE_HIGH>;
+		num-chipselects = <1>;
+		cs-gpios = <&gpio0 ASPEED_GPIO(Z, 0) GPIO_ACTIVE_LOW>;
+
+		tpm@0 {
+			compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
+			spi-max-frequency = <33000000>;
+			reg = <0>;
+		};
+	};
+};
+
+&uart6 {
+	status = "okay";
+};
+
+&wdt1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst1_default>;
+	aspeed,reset-type = "soc";
+	aspeed,external-signal;
+	aspeed,ext-push-pull;
+	aspeed,ext-active-high;
+	aspeed,ext-pulse-duration = <256>;
+};
+
+&mac3 {
+	status = "okay";
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+	fixed-link {
+		speed = <100>;
+		full-duplex;
+	};
+};
+
+&mdio3 {
+	status = "okay";
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-128.dtsi"
+	};
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "alt-bmc";
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&sgpiom0 {
+	status = "okay";
+	ngpios = <128>;
+	bus-frequency = <2000000>;
+};
+
+&i2c0 {
+	status = "okay";
+
+	power-monitor@40 {
+		compatible = "ti,ina230";
+		reg = <0x40>;
+		shunt-resistor = <1000>;
+	};
+
+	power-monitor@41 {
+		compatible = "ti,ina230";
+		reg = <0x41>;
+		shunt-resistor = <1000>;
+	};
+
+	power-monitor@44 {
+		compatible = "lltc,ltc4287";
+		reg = <0x44>;
+		shunt-resistor-micro-ohms = <2000>;
+	};
+
+	power-monitor@43 {
+		compatible = "infineon,xdp710";
+		reg = <0x43>;
+	};
+
+	leds_gpio: gpio@19 {
+		compatible = "nxp,pca9555";
+		reg = <0x19>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio@11 {
+		compatible = "nxp,pca9555";
+		reg = <0x11>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&sgpiom0>;
+		interrupts = <238 IRQ_TYPE_LEVEL_LOW>;
+
+		gpio-line-names =
+		"PWRGD_P24V_SMPWROK", "P1V5_PWROK",
+		"P3V3_PWROK", "P5V_PWROK",
+		"P12V_SCM_PWROK", "P12V_PWROK",
+		"P24V_PWROK", "P48V_HSC_PWROK",
+		"ERR_GPIO_IRQ", "TMP75_ALERT_N",
+		"BMC_PWROK", "P12V_INA230_ALERT_N",
+		"P24V_INA230_ALERT_N","",
+		"P48V_HSC_ALERT_N", "P1V05_PWROK";
+	};
+
+	gpio@12 {
+		compatible = "nxp,pca9555";
+		reg = <0x12>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&sgpiom0>;
+		interrupts = <240 IRQ_TYPE_LEVEL_LOW>;
+
+		gpio-line-names =
+		"P1V05_PWR_FAIL", "P1V5_PWR_FAIL",
+		"P24V_PWR_FAIL", "P24V_SM_PWR_FAIL",
+		"IRQ_NW0/1/2_N", "IRQ_NW3/4/5_N",
+		"RTC_INT_N_R", "ERR_GPIO_IRQ",
+		"", "",
+		"", "",
+		"", "",
+		"", "";
+	};
+
+	gpio@13 {
+		compatible = "nxp,pca9555";
+		reg = <0x13>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&sgpiom0>;
+		interrupts = <242 IRQ_TYPE_LEVEL_LOW>;
+
+		gpio-line-names =
+		"", "",
+		"", "",
+		"", "",
+		"", "",
+		"RACKMON_A_1", "RACKMON_A_2",
+		"RACKMON_B_1", "RACKMON_B_2",
+		"", "",
+		"", "";
+	};
+};
+
+&i2c1 {
+	status = "okay";
+
+	temperature-sensor@4b {
+		compatible = "ti,tmp75";
+		reg = <0x4b>;
+	};
+
+	temperature-sensor@4f {
+		compatible = "ti,tmp75";
+		reg = <0x4f>;
+	};
+
+	eeprom@54 {
+		compatible = "atmel,24c128";
+		reg = <0x54>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	i2c-mux@77 {
+		compatible = "nxp,pca9548";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		// FCB 1
+		imux16: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom@50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			pwm@5e {
+				compatible = "maxim,max31790";
+				reg = <0x5e>;
+			};
+
+			power-sensor@40 {
+				compatible = "ti,ina238";
+				reg = <0x40>;
+				shunt-resistor = <1000>;
+			};
+
+			power-sensor@41 {
+				compatible = "ti,ina238";
+				reg = <0x41>;
+				shunt-resistor = <1000>;
+			};
+
+			power-sensor@44 {
+				compatible = "ti,ina238";
+				reg = <0x44>;
+				shunt-resistor = <1000>;
+			};
+
+			power-sensor@45 {
+				compatible = "ti,ina238";
+				reg = <0x45>;
+				shunt-resistor = <1000>;
+			};
+
+			temperature-sensor@4b {
+				compatible = "ti,tmp75";
+				reg = <0x4b>;
+			};
+
+			gpio@11 {
+				compatible = "nxp,pca9555";
+				reg = <0x11>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <218 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+				"P48V_FAN1_PWRGD_R", "P48V_FAN2_PWRGD_R",
+				"P48V_FAN3_PWRGD_R", "P48V_FAN4_PWRGD_R",
+				"FCB_1_P48V_ZONE0_PWRGD_R", "FCB_1_P48V_ZONE1_PWRGD_R",
+				"FCB_1_PWRGD_P3V3_R", "",
+				"", "",
+				"", "",
+				"", "",
+				"", "";
+			};
+
+			gpio@12 {
+				compatible = "nxp,pca9555";
+				reg = <0x12>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <218 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+				"INA238_FAN1_ALERT_N", "INA238_FAN2_ALERT_N",
+				"INA238_FAN3_ALERT_N", "INA238_FAN4_ALERT_N",
+				"FCB_1_TMP75_ALERT_N", "",
+				"", "",
+				"FAN1_PRSNT", "FAN2_PRSNT",
+				"FAN3_PRSNT", "FAN4_PRSNT",
+				"", "",
+				"", "";
+			};
+
+			gpio@13 {
+				compatible = "nxp,pca9555";
+				reg = <0x13>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <218 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+				"FAN1_IL_TACH_ALERT", "FAN1_OL_TACH_ALERT",
+				"FAN2_IL_TACH_ALERT", "FAN2_OL_TACH_ALERT",
+				"FAN3_IL_TACH_ALERT", "FAN3_OL_TACH_ALERT",
+				"FAN4_IL_TACH_ALERT", "FAN4_IL_TACH_ALERT",
+				"", "",
+				"", "",
+				"", "",
+				"", "";
+			};
+
+			gpio@17 {
+				compatible = "nxp,pca9555";
+				reg = <0x17>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <218 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+				"FCB_1_P1V0_POWER_FAIL", "FCB_1_P1V8_POWER_FAIL",
+				"FCB_1_P48V_ZONE0_POWER_FAIL", "FAN1_POWER_FAIL",
+				"FAN2_POWER_FAIL", "FAN3_POWER_FAIL",
+				"FAN4_POWER_FAIL", "",
+				"", "",
+				"", "",
+				"", "",
+				"", "";
+			};
+		};
+		// FCB 2
+		imux17: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			pwm@5e {
+				compatible = "maxim,max31790";
+				reg = <0x5e>;
+			};
+
+			power-sensor@40 {
+				compatible = "ti,ina238";
+				reg = <0x40>;
+				shunt-resistor = <1000>;
+			};
+
+			power-sensor@41 {
+				compatible = "ti,ina238";
+				reg = <0x41>;
+				shunt-resistor = <1000>;
+			};
+
+			power-sensor@44 {
+				compatible = "ti,ina238";
+				reg = <0x44>;
+				shunt-resistor = <1000>;
+			};
+
+			power-sensor@45 {
+				compatible = "ti,ina238";
+				reg = <0x45>;
+				shunt-resistor = <1000>;
+			};
+
+			temperature-sensor@4b {
+				compatible = "ti,tmp75";
+				reg = <0x4b>;
+			};
+
+			gpio@11 {
+				compatible = "nxp,pca9555";
+				reg = <0x11>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <220 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+				"P48V_FAN5_PWRGD_R", "P48V_FAN6_PWRGD_R",
+				"P48V_FAN7_PWRGD_R", "P48V_FAN8_PWRGD_R",
+				"FCB_2_P48V_ZONE0_PWRGD_R", "FCB_2_P48V_ZONE1_PWRGD_R",
+				"FCB_2_PWRGD_P3V3_R", "",
+				"", "",
+				"", "",
+				"", "",
+				"", "";
+			};
+
+			gpio@12 {
+				compatible = "nxp,pca9555";
+				reg = <0x12>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <220 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+				"INA238_FAN5_ALERT_N", "INA238_FAN6_ALERT_N",
+				"INA238_FAN7_ALERT_N", "INA238_FAN8_ALERT_N",
+				"FCB_2_TMP75_ALERT_N", "",
+				"", "",
+				"FAN5_PRSNT", "FAN6_PRSNT",
+				"FAN7_PRSNT", "FAN8_PRSNT",
+				"", "",
+				"", "";
+			};
+
+			gpio@13 {
+				compatible = "nxp,pca9555";
+				reg = <0x13>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <220 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+				"FAN5_IL_TACH_ALERT", "FAN5_OL_TACH_ALERT",
+				"FAN6_IL_TACH_ALERT", "FAN6_OL_TACH_ALERT",
+				"FAN7_IL_TACH_ALERT", "FAN7_OL_TACH_ALERT",
+				"FAN8_IL_TACH_ALERT", "FAN8_IL_TACH_ALERT",
+				"", "",
+				"", "",
+				"", "",
+				"", "";
+			};
+
+			gpio@17 {
+				compatible = "nxp,pca9555";
+				reg = <0x17>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <220 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+				"FCB_2_P1V0_POWER_FAIL", "FCB_2_P1V8_POWER_FAIL",
+				"FCB_2_P48V_ZONE0_POWER_FAIL", "FAN5_POWER_FAIL",
+				"FAN6_POWER_FAIL", "FAN7_POWER_FAIL",
+				"FAN8_POWER_FAIL", "",
+				"", "",
+				"", "",
+				"", "",
+				"", "";
+			};
+		};
+		// FCB 3
+		imux18: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			eeprom@50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			pwm@5e {
+				compatible = "maxim,max31790";
+				reg = <0x5e>;
+			};
+
+			power-sensor@40 {
+				compatible = "ti,ina238";
+				reg = <0x40>;
+				shunt-resistor = <1000>;
+			};
+
+			power-sensor@41 {
+				compatible = "ti,ina238";
+				reg = <0x41>;
+				shunt-resistor = <1000>;
+			};
+
+			power-sensor@44 {
+				compatible = "ti,ina238";
+				reg = <0x44>;
+				shunt-resistor = <1000>;
+			};
+
+			power-sensor@45 {
+				compatible = "ti,ina238";
+				reg = <0x45>;
+				shunt-resistor = <1000>;
+			};
+
+			temperature-sensor@4b {
+				compatible = "ti,tmp75";
+				reg = <0x4b>;
+			};
+
+			gpio@11 {
+				compatible = "nxp,pca9555";
+				reg = <0x11>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <230 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+				"P48V_FAN9_PWRGD_R", "P48V_FAN10_PWRGD_R",
+				"P48V_FAN11_PWRGD_R", "P48V_FAN12_PWRGD_R",
+				"FCB_3_P48V_ZONE0_PWRGD_R", "FCB_3_P48V_ZONE1_PWRGD_R",
+				"FCB_3_PWRGD_P3V3_R", "",
+				"", "",
+				"", "",
+				"", "",
+				"", "";
+			};
+
+			gpio@12 {
+				compatible = "nxp,pca9555";
+				reg = <0x12>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <230 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+				"INA238_FAN9_ALERT_N", "INA238_FAN10_ALERT_N",
+				"INA238_FAN11_ALERT_N", "INA238_FAN12_ALERT_N",
+				"FCB_3_TMP75_ALERT_N", "",
+				"", "",
+				"FAN9_PRSNT", "FAN10_PRSNT",
+				"FAN11_PRSNT", "FAN12_PRSNT",
+				"", "",
+				"", "";
+			};
+
+			gpio@13 {
+				compatible = "nxp,pca9555";
+				reg = <0x13>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <230 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+				"FAN9_IL_TACH_ALERT", "FAN9_OL_TACH_ALERT",
+				"FAN10_IL_TACH_ALERT", "FAN10_OL_TACH_ALERT",
+				"FAN11_IL_TACH_ALERT", "FAN11_OL_TACH_ALERT",
+				"FAN12_IL_TACH_ALERT", "FAN12_IL_TACH_ALERT",
+				"", "",
+				"", "",
+				"", "",
+				"", "";
+			};
+
+			gpio@17 {
+				compatible = "nxp,pca9555";
+				reg = <0x17>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <230 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+				"FCB_3_P1V0_POWER_FAIL", "FCB_3_P1V8_POWER_FAIL",
+				"FCB_3_P48V_ZONE0_POWER_FAIL", "FAN9_POWER_FAIL",
+				"FAN10_POWER_FAIL", "FAN11_POWER_FAIL",
+				"FAN12_POWER_FAIL", "",
+				"", "",
+				"", "",
+				"", "",
+				"", "";
+			};
+		};
+		// FCB 4
+		imux19: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			eeprom@50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			pwm@5e {
+				compatible = "maxim,max31790";
+				reg = <0x5e>;
+			};
+
+			power-sensor@40 {
+				compatible = "ti,ina238";
+				reg = <0x40>;
+				shunt-resistor = <1000>;
+			};
+
+			power-sensor@41 {
+				compatible = "ti,ina238";
+				reg = <0x41>;
+				shunt-resistor = <1000>;
+			};
+
+			power-sensor@44 {
+				compatible = "ti,ina238";
+				reg = <0x44>;
+				shunt-resistor = <1000>;
+			};
+
+			power-sensor@45 {
+				compatible = "ti,ina238";
+				reg = <0x45>;
+				shunt-resistor = <1000>;
+			};
+
+			temperature-sensor@4b {
+				compatible = "ti,tmp75";
+				reg = <0x4b>;
+			};
+
+			gpio@11 {
+				compatible = "nxp,pca9555";
+				reg = <0x11>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <232 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+				"P48V_FAN13_PWRGD_R", "P48V_FAN14_PWRGD_R",
+				"P48V_FAN15_PWRGD_R", "P48V_FAN16_PWRGD_R",
+				"FCB_4_P48V_ZONE0_PWRGD_R", "FCB_4_P48V_ZONE1_PWRGD_R",
+				"FCB_4_PWRGD_P3V3_R", "",
+				"", "",
+				"", "",
+				"", "",
+				"", "";
+			};
+
+			gpio@12 {
+				compatible = "nxp,pca9555";
+				reg = <0x12>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <232 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+				"INA238_FAN13_ALERT_N", "INA238_FAN14_ALERT_N",
+				"INA238_FAN15_ALERT_N", "INA238_FAN16_ALERT_N",
+				"FCB_4_TMP75_ALERT_N", "",
+				"", "",
+				"FAN13_PRSNT", "FAN14_PRSNT",
+				"FAN15_PRSNT", "FAN16_PRSNT",
+				"", "",
+				"", "";
+			};
+
+			gpio@13 {
+				compatible = "nxp,pca9555";
+				reg = <0x13>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <232 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+				"FAN13_IL_TACH_ALERT", "FAN13_OL_TACH_ALERT",
+				"FAN14_IL_TACH_ALERT", "FAN14_OL_TACH_ALERT",
+				"FAN15_IL_TACH_ALERT", "FAN15_OL_TACH_ALERT",
+				"FAN16_IL_TACH_ALERT", "FAN16_IL_TACH_ALERT",
+				"", "",
+				"", "",
+				"", "",
+				"", "";
+			};
+
+			gpio@17 {
+				compatible = "nxp,pca9555";
+				reg = <0x17>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <232 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+				"FCB_4_P1V0_POWER_FAIL", "FCB_4_P1V8_POWER_FAIL",
+				"FCB_4_P48V_ZONE0_POWER_FAIL", "FAN13_POWER_FAIL",
+				"FAN14_POWER_FAIL", "FAN15_POWER_FAIL",
+				"FAN16_POWER_FAIL", "",
+				"", "",
+				"", "",
+				"", "",
+				"", "";
+			};
+		};
+		// FCB 5
+		imux20: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+
+			eeprom@50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			pwm@5e {
+				compatible = "maxim,max31790";
+				reg = <0x5e>;
+			};
+
+			power-sensor@40 {
+				compatible = "ti,ina238";
+				reg = <0x40>;
+				shunt-resistor = <1000>;
+			};
+
+			power-sensor@41 {
+				compatible = "ti,ina238";
+				reg = <0x41>;
+				shunt-resistor = <1000>;
+			};
+
+			power-sensor@44 {
+				compatible = "ti,ina238";
+				reg = <0x44>;
+				shunt-resistor = <1000>;
+			};
+
+			power-sensor@45 {
+				compatible = "ti,ina238";
+				reg = <0x45>;
+				shunt-resistor = <1000>;
+			};
+			temperature-sensor@4b {
+				compatible = "ti,tmp75";
+				reg = <0x4b>;
+			};
+
+			gpio@11 {
+				compatible = "nxp,pca9555";
+				reg = <0x11>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <254 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+				"P48V_FAN20_PWRGD_R", "P48V_FAN19_PWRGD_R",
+				"P48V_FAN18_PWRGD_R", "P48V_FAN17_PWRGD_R",
+				"FCB_5_P48V_ZONE0_PWRGD_R", "FCB_5_P48V_ZONE1_PWRGD_R",
+				"FCB_5_PWRGD_P3V3_R", "",
+				"", "",
+				"", "",
+				"", "",
+				"", "";
+			};
+
+			gpio@12 {
+				compatible = "nxp,pca9555";
+				reg = <0x12>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <254 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+				"INA238_FAN20_ALERT_N", "INA238_FAN19_ALERT_N",
+				"INA238_FAN18_ALERT_N", "INA238_FAN17_ALERT_N",
+				"FCB_5_TMP75_ALERT_N", "",
+				"", "",
+				"FAN20_PRSNT", "FAN19_PRSNT",
+				"FAN18_PRSNT", "FAN17_PRSNT",
+				"", "",
+				"", "";
+			};
+
+			gpio@13 {
+				compatible = "nxp,pca9555";
+				reg = <0x13>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <254 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+				"FAN20_IL_TACH_ALERT", "FAN20_OL_TACH_ALERT",
+				"FAN19_IL_TACH_ALERT", "FAN19_OL_TACH_ALERT",
+				"FAN18_IL_TACH_ALERT", "FAN18_OL_TACH_ALERT",
+				"FAN17_IL_TACH_ALERT", "FAN17_OL_TACH_ALERT",
+				"", "",
+				"", "",
+				"", "",
+				"", "";
+			};
+
+			gpio@17 {
+				compatible = "nxp,pca9555";
+				reg = <0x17>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <254 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+				"FCB_5_P1V0_POWER_FAIL", "FCB_5_P1V8_POWER_FAIL",
+				"FCB_5_P48V_ZONE0_POWER_FAIL", "FAN20_POWER_FAIL",
+				"FAN19_POWER_FAIL", "FAN18_POWER_FAIL",
+				"FAN17_POWER_FAIL", "",
+				"", "",
+				"", "",
+				"", "",
+				"", "";
+			};
+		};
+		// FCB 6
+		imux21: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+
+			eeprom@50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			pwm@5e {
+				compatible = "maxim,max31790";
+				reg = <0x5e>;
+			};
+
+			power-sensor@40 {
+				compatible = "ti,ina238";
+				reg = <0x40>;
+				shunt-resistor = <1000>;
+			};
+
+			power-sensor@41 {
+				compatible = "ti,ina238";
+				reg = <0x41>;
+				shunt-resistor = <1000>;
+			};
+
+			power-sensor@44 {
+				compatible = "ti,ina238";
+				reg = <0x44>;
+				shunt-resistor = <1000>;
+			};
+
+			power-sensor@45 {
+				compatible = "ti,ina238";
+				reg = <0x45>;
+				shunt-resistor = <1000>;
+			};
+			temperature-sensor@4b {
+				compatible = "ti,tmp75";
+				reg = <0x4b>;
+			};
+
+			gpio@11 {
+				compatible = "nxp,pca9555";
+				reg = <0x11>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <252 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+				"P48V_FAN24_PWRGD_R", "P48V_FAN23_PWRGD_R",
+				"P48V_FAN22_PWRGD_R", "P48V_FAN21_PWRGD_R",
+				"FCB_6_P48V_ZONE0_PWRGD_R", "FCB_6_P48V_ZONE1_PWRGD_R",
+				"FCB_6_PWRGD_P3V3_R", "",
+				"", "",
+				"", "",
+				"", "",
+				"", "";
+			};
+
+			gpio@12 {
+				compatible = "nxp,pca9555";
+				reg = <0x12>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <252 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+				"INA238_FAN24_ALERT_N", "INA238_FAN23_ALERT_N",
+				"INA238_FAN22_ALERT_N", "INA238_FAN21_ALERT_N",
+				"FCB_6_TMP75_ALERT_N", "",
+				"", "",
+				"FAN24_PRSNT", "FAN23_PRSNT",
+				"FAN22_PRSNT", "FAN21_PRSNT",
+				"", "",
+				"", "";
+			};
+
+			gpio@13 {
+				compatible = "nxp,pca9555";
+				reg = <0x13>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <252 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+				"FAN24_IL_TACH_ALERT", "FAN24_OL_TACH_ALERT",
+				"FAN23_IL_TACH_ALERT", "FAN23_OL_TACH_ALERT",
+				"FAN22_IL_TACH_ALERT", "FAN22_OL_TACH_ALERT",
+				"FAN21_IL_TACH_ALERT", "FAN21_OL_TACH_ALERT",
+				"", "",
+				"", "",
+				"", "",
+				"", "";
+			};
+
+			gpio@17 {
+				compatible = "nxp,pca9555";
+				reg = <0x17>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-parent = <&sgpiom0>;
+				interrupts = <252 IRQ_TYPE_LEVEL_LOW>;
+
+				gpio-line-names =
+				"FCB_6_P1V0_POWER_FAIL", "FCB_6_P1V8_POWER_FAIL",
+				"FCB_6_P48V_ZONE0_POWER_FAIL", "FAN24_POWER_FAIL",
+				"FAN23_POWER_FAIL", "FAN22_POWER_FAIL",
+				"FAN21_POWER_FAIL", "",
+				"", "",
+				"", "",
+				"", "",
+				"", "";
+			};
+		};
+
+		imux22: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		imux23: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+&i2c3 {
+	status = "okay";
+
+	i2c-mux@72 {
+		compatible = "nxp,pca9545";
+		reg = <0x72>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		imux24: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		imux25: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		imux26: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		imux27: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+	};
+};
+
+&i2c4 {
+	status = "okay";
+
+	i2c-mux@72 {
+		compatible = "nxp,pca9545";
+		reg = <0x72>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		imux28: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		imux29: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		imux30: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		imux31: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	i2c-mux@72 {
+		compatible = "nxp,pca9545";
+		reg = <0x72>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		imux32: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		imux33: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		imux34: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		imux35: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+	};
+};
+
+&i2c6 {
+	status = "okay";
+
+	i2c-mux@72 {
+		compatible = "nxp,pca9545";
+		reg = <0x72>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		imux36: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		imux37: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		imux38: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		imux39: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+	};
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+
+	rtc@68 {
+		compatible = "dallas,ds1339";
+		reg = <0x68>;
+	};
+};
+
+&i2c12 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9545";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		imux40: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		imux41: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		imux42: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		imux43: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&i2c13 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9545";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		imux44: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		imux45: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		imux46: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		imux47: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&i2c14 {
+	status = "okay";
+	multi-master;
+
+	ipmb@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
+};
+
+&i2c15 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+
+	eeprom@56 {
+		compatible = "atmel,24c64";
+		reg = <0x56>;
+	};
+};
+
+&adc0 {
+	aspeed,int-vref-microvolt = <2500000>;
+	status = "okay";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+		&pinctrl_adc2_default &pinctrl_adc3_default
+		&pinctrl_adc4_default &pinctrl_adc5_default
+		&pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+	aspeed,int-vref-microvolt = <2500000>;
+	status = "okay";
+	pinctrl-0 = <&pinctrl_adc10_default>;
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&uhci {
+	status = "okay";
+};
+
+&gpio0 {
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","","","",
+	/*B0-B7*/	"","","","","","","","",
+	/*C0-C7*/	"","","","","BLADE_UART_SEL2","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"","","","","","","","",
+	/*F0-F7*/	"","","","","","","","",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"","","","","","","","",
+	/*I0-I7*/	"","","","","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","BLADE_UART_SEL0","","","",
+	/*M0-M7*/	"","","","","","BLADE_UART_SEL1","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"","","","","","","","",
+	/*Q0-Q7*/	"","","","","","power-chassis-control","","",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","","","","","","host0-ready",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","BAT_DETECT","","power-chassis-good","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","BLADE_UART_SEL3","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"","","","","","","","";
+};
+
+&sgpiom0 {
+	gpio-line-names =
+	/*"input pin","output pin"*/
+	/*A0 - A7*/
+	"PRSNT_MTIA_BLADE1_N","PWREN_MTIA_BLADE1_EN_N",
+	"PRSNT_MTIA_BLADE2_N","PWREN_MTIA_BLADE2_EN_N",
+	"PRSNT_MTIA_BLADE3_N","PWREN_MTIA_BLADE3_EN_N",
+	"PRSNT_MTIA_BLADE4_N","PWREN_MTIA_BLADE4_EN_N",
+	"PRSNT_MTIA_BLADE5_N","PWREN_MTIA_BLADE5_EN_N",
+	"PRSNT_MTIA_BLADE6_N","PWREN_MTIA_BLADE6_EN_N",
+	"PRSNT_MTIA_BLADE7_N","PWREN_MTIA_BLADE7_EN_N",
+	"PRSNT_MTIA_BLADE8_N","PWREN_MTIA_BLADE8_EN_N",
+	/*B0 - B7*/
+	"PRSNT_MTIA_BLADE9_N","PWREN_MTIA_BLADE9_EN_N",
+	"PRSNT_MTIA_BLADE10_N","PWREN_MTIA_BLADE10_EN_N",
+	"PRSNT_MTIA_BLADE11_N","PWREN_MTIA_BLADE11_EN_N",
+	"PRSNT_MTIA_BLADE12_N","PWREN_MTIA_BLADE12_EN_N",
+	"PRSNT_MTIA_BLADE13_N","PWREN_MTIA_BLADE13_EN_N",
+	"PRSNT_MTIA_BLADE14_N","PWREN_MTIA_BLADE14_EN_N",
+	"PRSNT_MTIA_BLADE15_N","PWREN_MTIA_BLADE15_EN_N",
+	"PRSNT_MTIA_BLADE16_N","PWREN_MTIA_BLADE16_EN_N",
+	/*C0 - C7*/
+	"PRSNT_NW_BLADE1_N","PWREN_NW_BLADE1_EN_N",
+	"PRSNT_NW_BLADE2_N","PWREN_NW_BLADE2_EN_N",
+	"PRSNT_NW_BLADE3_N","PWREN_NW_BLADE3_EN_N",
+	"PRSNT_NW_BLADE4_N","PWREN_NW_BLADE4_EN_N",
+	"PRSNT_NW_BLADE5_N","PWREN_NW_BLADE5_EN_N",
+	"PRSNT_NW_BLADE6_N","PWREN_NW_BLADE6_EN_N",
+	"PRSNT_FCB_1_N","PWREN_MTIA_BLADE1_HSC_EN_N",
+	"PRSNT_FCB_2_N","PWREN_MTIA_BLADE2_HSC_EN_N",
+	/*D0 - D7*/
+	"PRSNT_FCB_3_N","PWREN_MTIA_BLADE3_HSC_EN_N",
+	"PRSNT_FCB_4_N","PWREN_MTIA_BLADE4_HSC_EN_N",
+	"PRSNT_FCB_6_N","PWREN_MTIA_BLADE5_HSC_EN_N",
+	"PRSNT_FCB_5_N","PWREN_MTIA_BLADE6_HSC_EN_N",
+	"PWRGD_MTIA_BLADE1_PWROK_N","PWREN_MTIA_BLADE7_HSC_EN_N",
+	"PWRGD_MTIA_BLADE2_PWROK_N","PWREN_MTIA_BLADE8_HSC_EN_N",
+	"PWRGD_MTIA_BLADE3_PWROK_N","PWREN_MTIA_BLADE9_HSC_EN_N",
+	"PWRGD_MTIA_BLADE4_PWROK_N","PWREN_MTIA_BLADE10_HSC_EN_N",
+	/*E0 - E7*/
+	"PWRGD_MTIA_BLADE5_PWROK_N","PWREN_MTIA_BLADE11_HSC_EN_N",
+	"PWRGD_MTIA_BLADE6_PWROK_N","PWREN_MTIA_BLADE12_HSC_EN_N",
+	"PWRGD_MTIA_BLADE7_PWROK_N","PWREN_MTIA_BLADE13_HSC_EN_N",
+	"PWRGD_MTIA_BLADE8_PWROK_N","PWREN_MTIA_BLADE14_HSC_EN_N",
+	"PWRGD_MTIA_BLADE9_PWROK_N","PWREN_MTIA_BLADE15_HSC_EN_N",
+	"PWRGD_MTIA_BLADE10_PWROK_N","PWREN_MTIA_BLADE16_HSC_EN_N",
+	"PWRGD_MTIA_BLADE11_PWROK_N","PWREN_NW_BLADE1_HSC_EN_N",
+	"PWRGD_MTIA_BLADE12_PWROK_N","PWREN_NW_BLADE2_HSC_EN_N",
+	/*F0 - F7*/
+	"PWRGD_MTIA_BLADE13_PWROK_N","PWREN_NW_BLADE3_HSC_EN_N",
+	"PWRGD_MTIA_BLADE14_PWROK_N","PWREN_NW_BLADE4_HSC_EN_N",
+	"PWRGD_MTIA_BLADE15_PWROK_N","PWREN_NW_BLADE5_HSC_EN_N",
+	"PWRGD_MTIA_BLADE16_PWROK_N","PWREN_NW_BLADE6_HSC_EN_N",
+	"PWRGD_NW_BLADE1_PWROK_N","PWREN_SGPIO_FCB_2_EN_N",
+	"PWRGD_NW_BLADE2_PWROK_N","PWREN_SGPIO_FCB_1_EN_N",
+	"PWRGD_NW_BLADE3_PWROK_N","PWREN_SGPIO_FCB_4_EN_N",
+	"PWRGD_NW_BLADE4_PWROK_N","PWREN_SGPIO_FCB_3_EN_N",
+	/*G0 - G7*/
+	"PWRGD_NW_BLADE5_PWROK_N","PWREN_SGPIO_FCB_5_EN_N",
+	"PWRGD_NW_BLADE6_PWROK_N","PWREN_SGPIO_FCB_6_EN_N",
+	"PWRGD_FCB_1","FM_BMC_RST_RTCRST_R",
+	"PWRGD_FCB_2","",
+	"PWRGD_FCB_3","FM_MDIO_SW_SEL",
+	"PWRGD_FCB_4","FM_P24V_SMPWR_EN",
+	"PWRGD_FCB_6","",
+	"PWRGD_FCB_5","",
+	/*H0 - H7*/
+	"LEAK_DETECT_MTIA_BLADE1_N","",
+	"LEAK_DETECT_MTIA_BLADE2_N","",
+	"LEAK_DETECT_MTIA_BLADE3_N","",
+	"LEAK_DETECT_MTIA_BLADE4_N","",
+	"LEAK_DETECT_MTIA_BLADE5_N","",
+	"LEAK_DETECT_MTIA_BLADE6_N","",
+	"LEAK_DETECT_MTIA_BLADE7_N","ERR_INJECT_CMM_PWR_FAIL_N",
+	"LEAK_DETECT_MTIA_BLADE8_N","",
+	/*I0 - I7*/
+	"LEAK_DETECT_MTIA_BLADE9_N","RST_I2CRST_FCB_5_N",
+	"LEAK_DETECT_MTIA_BLADE10_N","RST_I2CRST_FCB_6_N",
+	"LEAK_DETECT_MTIA_BLADE11_N","RST_I2CRST_FCB_4_N",
+	"LEAK_DETECT_MTIA_BLADE12_N","RST_I2CRST_FCB_3_N",
+	"LEAK_DETECT_MTIA_BLADE13_N","RST_I2CRST_FCB_2_N",
+	"LEAK_DETECT_MTIA_BLADE14_N","RST_I2CRST_FCB_1_N",
+	"LEAK_DETECT_MTIA_BLADE15_N","BMC_READY",
+	"LEAK_DETECT_MTIA_BLADE16_N","FM_88E6393X_BIN_UPDATE_EN_N",
+	/*J0 - J7*/
+	"LEAK_DETECT_NW_BLADE1_N","WATER_VALVE_CLOSED_N",
+	"LEAK_DETECT_NW_BLADE2_N","",
+	"LEAK_DETECT_NW_BLADE3_N","",
+	"LEAK_DETECT_NW_BLADE4_N","",
+	"LEAK_DETECT_NW_BLADE5_N","",
+	"LEAK_DETECT_NW_BLADE6_N","",
+	"PWRGD_MTIA_BLADE1_HSC_PWROK_N","",
+	"PWRGD_MTIA_BLADE2_HSC_PWROK_N","",
+	/*K0 - K7*/
+	"PWRGD_MTIA_BLADE3_HSC_PWROK_N","",
+	"PWRGD_MTIA_BLADE4_HSC_PWROK_N","",
+	"PWRGD_MTIA_BLADE5_HSC_PWROK_N","",
+	"PWRGD_MTIA_BLADE6_HSC_PWROK_N","",
+	"PWRGD_MTIA_BLADE7_HSC_PWROK_N","",
+	"PWRGD_MTIA_BLADE8_HSC_PWROK_N","",
+	"PWRGD_MTIA_BLADE9_HSC_PWROK_N","",
+	"PWRGD_MTIA_BLADE10_HSC_PWROK_N","",
+	/*L0 - L7*/
+	"PWRGD_MTIA_BLADE11_HSC_PWROK_N","",
+	"PWRGD_MTIA_BLADE12_HSC_PWROK_N","",
+	"PWRGD_MTIA_BLADE13_HSC_PWROK_N","",
+	"PWRGD_MTIA_BLADE14_HSC_PWROK_N","",
+	"PWRGD_MTIA_BLADE15_HSC_PWROK_N","",
+	"PWRGD_MTIA_BLADE16_HSC_PWROK_N","",
+	"PWRGD_NW_BLADE1_HSC_PWROK_N","",
+	"PWRGD_NW_BLADE2_HSC_PWROK_N","",
+	/*M0 - M7*/
+	"PWRGD_NW_BLADE3_HSC_PWROK_N","",
+	"PWRGD_NW_BLADE4_HSC_PWROK_N","",
+	"PWRGD_NW_BLADE5_HSC_PWROK_N","",
+	"PWRGD_NW_BLADE6_HSC_PWROK_N","",
+	"RPU_READY","",
+	"IT_GEAR_RPU_LINK_N","",
+	"IT_GEAR_LEAK","",
+	"WATER_VALVE_CLOSED_N","",
+	/*N0 - N7*/
+	"VALVE_STATUS_0","",
+	"VALVE_STATUS_1","",
+	"PCA9555_IRQ1_N","",
+	"PCA9555_IRQ2_N","",
+	"CR_TOGGLE_BOOT_N","",
+	"IRQ_FCB_1_N","",
+	"IRQ_FCB_2_N","",
+	"CMM_CABLE_CARTRIDGE_PRSNT_BOT_N","",
+	/*O0 - O7*/
+	"CMM_CABLE_CARTRIDGE_PRSNT_TOP_N","",
+	"BOT_BCB_CABLE_PRSNT_N","",
+	"TOP_BCB_CABLE_PRSNT_N","",
+	"IRQ_FCB_3_N","",
+	"IRQ_FCB_4_N","",
+	"CHASSIS_LEAK0_DETECT_N","",
+	"CHASSIS_LEAK1_DETECT_N","",
+	"PCA9555_IRQ3_N","",
+	/*P0 - P7*/
+	"PCA9555_IRQ4_N","",
+	"PCA9555_IRQ5_N","",
+	"CMM_AC_PWR_BTN_N","",
+	"RPU_READY_SPARE","",
+	"IT_GEAR_LEAK_SPARE","",
+	"IT_GEAR_RPU_LINK_SPARE_N","",
+	"IRQ_FCB_6_N","",
+	"IRQ_FCB_5_N","";
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-minipack.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minipack.dts
index 230d16cd9967..aafd1042b6e5 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-minipack.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-minipack.dts
@@ -344,7 +344,7 @@
 	 * I2C Switch 2-0070 is connecting to SCM (System Controller
 	 * Module).
 	 */
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -425,7 +425,7 @@
 &i2c8 {
 	status = "okay";
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -441,7 +441,7 @@
 			#size-cells = <0>;
 			reg = <0>;
 
-			i2c-switch@71 {
+			i2c-mux@71 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -507,7 +507,7 @@
 			#size-cells = <0>;
 			reg = <1>;
 
-			i2c-switch@72 {
+			i2c-mux@72 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -573,7 +573,7 @@
 			#size-cells = <0>;
 			reg = <2>;
 
-			i2c-switch@76 {
+			i2c-mux@76 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -639,7 +639,7 @@
 			#size-cells = <0>;
 			reg = <3>;
 
-			i2c-switch@76 {
+			i2c-mux@76 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -729,7 +729,7 @@
 	 * I2C Switch 9-0070 is connecting to MAC/PHY EEPROMs on SMB
 	 * (Switch Main Board).
 	 */
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -793,7 +793,7 @@
 &i2c11 {
 	status = "okay";
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -809,7 +809,7 @@
 			#size-cells = <0>;
 			reg = <0>;
 
-			i2c-switch@73 {
+			i2c-mux@73 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -875,7 +875,7 @@
 			#size-cells = <0>;
 			reg = <1>;
 
-			i2c-switch@73 {
+			i2c-mux@73 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -941,7 +941,7 @@
 			#size-cells = <0>;
 			reg = <2>;
 
-			i2c-switch@73 {
+			i2c-mux@73 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1007,7 +1007,7 @@
 			#size-cells = <0>;
 			reg = <3>;
 
-			i2c-switch@73 {
+			i2c-mux@73 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1073,7 +1073,7 @@
 			#size-cells = <0>;
 			reg = <4>;
 
-			i2c-switch@73 {
+			i2c-mux@73 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1139,7 +1139,7 @@
 			#size-cells = <0>;
 			reg = <5>;
 
-			i2c-switch@73 {
+			i2c-mux@73 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1205,7 +1205,7 @@
 			#size-cells = <0>;
 			reg = <6>;
 
-			i2c-switch@73 {
+			i2c-mux@73 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1271,7 +1271,7 @@
 			#size-cells = <0>;
 			reg = <7>;
 
-			i2c-switch@73 {
+			i2c-mux@73 {
 				compatible = "nxp,pca9548";
 				#address-cells = <1>;
 				#size-cells = <0>;
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-santabarbara.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-santabarbara.dts
new file mode 100644
index 000000000000..72c84f31bdf6
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-santabarbara.dts
@@ -0,0 +1,982 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2025 Facebook Inc.
+
+/dts-v1/;
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
+
+/ {
+	model = "Facebook Santabarbara BMC";
+	compatible = "facebook,santabarbara-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial0 = &uart1;
+		serial2 = &uart3;
+		serial3 = &uart4;
+		serial4 = &uart5;
+		i2c16 = &i2c4mux0ch0;
+		i2c17 = &i2c4mux0ch1;
+		i2c18 = &i2c4mux0ch2;
+		i2c19 = &i2c4mux0ch3;
+		i2c20 = &i2c4mux0ch4;
+		i2c21 = &i2c4mux0ch5;
+		i2c22 = &i2c4mux0ch6;
+		i2c23 = &i2c4mux0ch7;
+		i2c24 = &i2c5mux0ch0;
+		i2c25 = &i2c5mux0ch1;
+		i2c26 = &i2c5mux0ch2;
+		i2c27 = &i2c5mux0ch3;
+		i2c28 = &i2c5mux1ch0;
+		i2c29 = &i2c5mux1ch1;
+		i2c30 = &i2c5mux1ch2;
+		i2c31 = &i2c5mux1ch3;
+		i2c32 = &i2c12mux0ch0;
+		i2c33 = &i2c12mux0ch1;
+		i2c34 = &i2c12mux0ch2;
+		i2c35 = &i2c12mux0ch3;
+		i2c36 = &i2c12mux0ch4;
+		i2c37 = &i2c12mux0ch5;
+		i2c38 = &i2c12mux0ch6;
+		i2c39 = &i2c12mux0ch7;
+	};
+
+	chosen {
+		stdout-path = "serial4:57600n8";
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+			      <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+			      <&adc1 2>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "bmc_heartbeat_amber";
+			gpios = <&gpio0 ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-1 {
+			label = "fp_id_amber";
+			default-state = "off";
+			gpios = <&gpio0 ASPEED_GPIO(B, 5) GPIO_ACTIVE_HIGH>;
+		};
+
+		led-2 {
+			label = "power_blue";
+			default-state = "off";
+			gpios = <&gpio0 ASPEED_GPIO(P, 4) GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	p3v3_bmc_aux: regulator-p3v3-bmc-aux {
+		compatible = "regulator-fixed";
+		regulator-name = "p3v3_bmc_aux";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	spi_gpio: spi {
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sck-gpios = <&gpio0 ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio0 ASPEED_GPIO(Z, 4) GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpio0 ASPEED_GPIO(Z, 5) GPIO_ACTIVE_HIGH>;
+		num-chipselects = <1>;
+		cs-gpios = <&gpio0 ASPEED_GPIO(Z, 0) GPIO_ACTIVE_LOW>;
+		status = "okay";
+
+		tpm@0 {
+			compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
+			spi-max-frequency = <33000000>;
+			reg = <0>;
+		};
+	};
+};
+
+&adc0 {
+	aspeed,int-vref-microvolt = <2500000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+		&pinctrl_adc2_default &pinctrl_adc3_default
+		&pinctrl_adc4_default &pinctrl_adc5_default
+		&pinctrl_adc6_default &pinctrl_adc7_default>;
+	status = "okay";
+};
+
+&adc1 {
+	aspeed,int-vref-microvolt = <2500000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc10_default>;
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&fmc {
+	status = "okay";
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-128.dtsi"
+	};
+
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "alt-bmc";
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&gpio0 {
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","","","",
+	/*B0-B7*/	"rtc-battery-voltage-read-enable","","","BMC_READY",
+			"","led-identify","","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"","","","","","","","",
+	/*F0-F7*/	"","","","","","","","",
+	/*G0-G7*/	"FM_MUX1_SEL_R","","","","","","","",
+	/*H0-H7*/	"","","","","","","","",
+	/*I0-I7*/	"","","","","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"led-postcode-0","led-postcode-1",
+			"led-postcode-2","led-postcode-3",
+			"led-postcode-4","led-postcode-5",
+			"led-postcode-6","led-postcode-7",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"power-button","","reset-button","",
+			"led-power","","","",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","power-host-control","","","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"","","","","","","","";
+};
+
+&gpio1 {
+	gpio-line-names =
+	/*18A0-18A7*/	"","","","","","","","",
+	/*18B0-18B7*/	"","","","",
+				"FM_BOARD_BMC_REV_ID0","FM_BOARD_BMC_REV_ID1",
+				"FM_BOARD_BMC_REV_ID2","",
+	/*18C0-18C7*/	"SPI_BMC_BIOS_ROM_IRQ0_R_N","","","","","","","",
+	/*18D0-18D7*/	"","","","","","","","",
+	/*18E0-18E3*/	"FM_BMC_PROT_LS_EN","AC_PWR_BMC_BTN_R_N","","";
+};
+
+&i2c0 {
+	status = "okay";
+
+	// MB FRU
+	eeprom@53 {
+		compatible = "atmel,24c128";
+		reg = <0x53>;
+	};
+
+	rtc@68 {
+		compatible = "dallas,ds1339";
+		reg = <0x68>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+
+	gpio@20 {
+		compatible = "nxp,pca9555";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&sgpiom0>;
+		interrupts = <112 IRQ_TYPE_LEVEL_LOW>;
+		gpio-line-names =
+			"FM_NIC_PPS_IN_OE_N","FM_NIC_PPS_OUT_OE_N",
+			"FM_CPU0_TRIGGERTSC_OE_N","FM_NIC_PPS_IN_MUX_OE_N",
+			"FM_CPU0_CORETYPE0","FM_CPU0_CORETYPE1",
+			"FM_CPU0_CORETYPE2","FM_NIC_PPS_OUT_MUX_OE",
+			"CLKMUX_INPUT_LOSS_U45_R_N","FM_CPU0_SP7R1",
+			"FM_CPU0_SP7R2","FM_CPU0_SP7R3",
+			"FM_CPU0_SP7R4","",
+			"FM_NIC_PPS_IN_S0_R","FM_NIC_PPS_IN_S1_R";
+	};
+
+	fan-controller@21 {
+		compatible = "maxim,max31790";
+		reg = <0x21>;
+	};
+
+	gpio@22 {
+		compatible = "nxp,pca9555";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&sgpiom0>;
+		interrupts = <116 IRQ_TYPE_LEVEL_LOW>;
+		gpio-line-names =
+			"FM_CBL_PRSNT_0A_N","FM_CBL_PRSNT_0B_N",
+			"FM_CBL_PRSNT_1A_N","FM_CBL_PRSNT_1B_N",
+			"FM_MODULE_PWRGD_0A","FM_MODULE_PWRGD_0B",
+			"CLKMUX_INPUT_LOSS_U88_R_N","FM_MODULE_PWRGD_1B",
+			"","",
+			"CLKMUX_INPUT_LOSS_U83_R_N","CLKMUX_INPUT_LOSS_U84_R_N",
+			"FM_P3V3_E1S_0_FAULT_R_N","FM_P3V3_E1S_1_FAULT_R_N",
+			"E1S_0_P12V_ADC_R_ALERT","E1S_1_P12V_ADC_R_ALERT";
+	};
+
+	gpio@24 {
+		compatible = "nxp,pca9555";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&sgpiom0>;
+		interrupts = <114 IRQ_TYPE_LEVEL_LOW>;
+		gpio-line-names =
+			"FM_CBL_PRSNT_2A_N","FM_CBL_PRSNT_2B_N",
+			"FM_CBL_PRSNT_3A_N","FM_CBL_PRSNT_3B_N",
+			"FM_CBL_PRSNT_4A_N","FM_CBL_PRSNT_4B_N",
+			"FM_P3V3_NIC_400G_FAULT_R_N","FM_MODULE_PWRGD_2B",
+			"OCP_SFF_P12V_ADC_R_ALERT","FM_MODULE_PWRGD_3B",
+			"FM_THERMAL_ALERT_R_N","FM_MODULE_PWRGD_4B",
+			"FM_CBL_PRSNT_OSFP_A_N","FM_CBL_PRSNT_OSFP_B_N",
+			"FM_JTAG_MCIO_MUX_S0","FM_JTAG_MCIO_MUX_S1";
+	};
+
+	gpio@26 {
+		compatible = "nxp,pca9555";
+		reg = <0x26>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&sgpiom0>;
+		interrupts = <118 IRQ_TYPE_LEVEL_LOW>;
+		gpio-line-names =
+			"FAN_0_PRSNT_R1_N","FAN_1_PRSNT_R1_N",
+			"FAN_2_PRSNT_R1_N","FAN_3_PRSNT_R1_N",
+			"P12V_FAN_0_ADC_ALERT","P12V_FAN_1_ADC_ALERT",
+			"P12V_FAN_2_ADC_ALERT","P12V_FAN_3_ADC_ALERT",
+			"P12V_FAN0_PWRGD_R","P12V_FAN1_PWRGD_R",
+			"P12V_FAN2_PWRGD_R","P12V_FAN3_PWRGD_R",
+			"","","","";
+	};
+};
+
+&i2c4 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c4mux0ch0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			// HPM Board ID EEPROM
+			eeprom@51 {
+				compatible = "atmel,24c128";
+				reg = <0x51>;
+			};
+
+			// SCM Board ID EEPROM
+			eeprom@53 {
+				compatible = "atmel,24c128";
+				reg = <0x53>;
+			};
+		};
+		i2c4mux0ch1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c4mux0ch2: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c4mux0ch3: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			power-monitor@40 {
+				compatible = "ti,ina230";
+				reg = <0x40>;
+				shunt-resistor = <2000>;
+			};
+
+			power-monitor@42 {
+				compatible = "ti,ina230";
+				reg = <0x42>;
+				shunt-resistor = <2000>;
+			};
+
+			power-monitor@44 {
+				compatible = "ti,ina230";
+				reg = <0x44>;
+				shunt-resistor = <2000>;
+			};
+
+			power-monitor@46 {
+				compatible = "ti,ina230";
+				reg = <0x46>;
+				shunt-resistor = <2000>;
+			};
+
+			voltage-sensor@48 {
+				compatible = "ti,ads7830";
+				reg = <0x48>;
+				vref-supply = <&p3v3_bmc_aux>;
+			};
+
+			voltage-sensor@4a {
+				compatible = "ti,ads7830";
+				reg = <0x4a>;
+				vref-supply = <&p3v3_bmc_aux>;
+			};
+
+			temperature-sensor@4c {
+				compatible = "ti,tmp75";
+				reg = <0x4c>;
+			};
+
+			temperature-sensor@4e {
+				compatible = "ti,tmp75";
+				reg = <0x4e>;
+			};
+		};
+		i2c4mux0ch4: i2c@4 {
+			reg = <4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c4mux0ch5: i2c@5 {
+			reg = <5>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c4mux0ch6: i2c@6 {
+			reg = <6>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			power-monitor@40 {
+				compatible = "ti,ina230";
+				reg = <0x40>;
+				shunt-resistor = <2000>;
+			};
+
+			power-monitor@42 {
+				compatible = "ti,ina230";
+				reg = <0x42>;
+				shunt-resistor = <2000>;
+			};
+
+			power-monitor@44 {
+				compatible = "ti,ina230";
+				reg = <0x44>;
+				shunt-resistor = <2000>;
+			};
+
+			power-monitor@46 {
+				compatible = "ti,ina230";
+				reg = <0x46>;
+				shunt-resistor = <2000>;
+			};
+
+			voltage-sensor@48 {
+				compatible = "ti,ads7830";
+				reg = <0x48>;
+			};
+		};
+		i2c4mux0ch7: i2c@7 {
+			reg = <7>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			temperature-sensor@4b {
+				compatible = "ti,tmp75";
+				reg = <0x4b>;
+			};
+
+			temperature-sensor@4f {
+				compatible = "ti,tmp75";
+				reg = <0x4f>;
+			};
+
+			// FIO FRU
+			eeprom@53 {
+				compatible = "atmel,24c512";
+				reg = <0x53>;
+			};
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	// E1S BP FRU
+	eeprom@52 {
+		compatible = "atmel,24c64";
+		reg = <0x52>;
+	};
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9546";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c5mux0ch0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c5mux0ch1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c5mux0ch2: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c5mux0ch3: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	i2c-mux@72 {
+		compatible = "nxp,pca9546";
+		reg = <0x72>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c5mux1ch0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			voltage-sensor@48 {
+				compatible = "ti,ads7830";
+				reg = <0x48>;
+			};
+		};
+		i2c5mux1ch1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			temperature-sensor@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+		};
+		i2c5mux1ch2: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			power-monitor@40 {
+				compatible = "ti,ina230";
+				reg = <0x40>;
+				shunt-resistor = <2000>;
+			};
+
+			power-monitor@41 {
+				compatible = "ti,ina230";
+				reg = <0x41>;
+				shunt-resistor = <2000>;
+			};
+
+			power-monitor@44 {
+				compatible = "ti,ina230";
+				reg = <0x44>;
+				shunt-resistor = <2000>;
+			};
+
+			power-monitor@45 {
+				compatible = "ti,ina230";
+				reg = <0x45>;
+				shunt-resistor = <2000>;
+			};
+		};
+		i2c5mux1ch3: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			gpio@74 {
+				compatible = "nxp,pca9539";
+				reg = <0x74>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				gpio-line-names =
+					"P12V_E1S_ADC_ALERT","BUFF0_100M_LOSB_PLD",
+					"E1S_BP_SKU_ID0","E1S_BP_SKU_ID1",
+					"E1S_BP_SKU_ID2","E1S_BP_REV_ID0",
+					"E1S_BP_REV_ID1","E1S_BP_REV_ID2",
+					"P3V3_E1S_1_FAULT_R_N","P3V3_E1S_2_FAULT_R_N",
+					"P3V3_E1S_3_FAULT_R_N","P3V3_E1S_4_FAULT_R_N",
+					"P12V_E1S_1_FAULT_R_N","P12V_E1S_2_FAULT_R_N",
+					"P12V_E1S_3_FAULT_R_N","P12V_E1S_4_FAULT_R_N";
+			};
+		};
+	};
+};
+
+&i2c6 {
+	status = "okay";
+
+	// Rainbow0 FRU
+	eeprom@52 {
+		compatible = "atmel,24c256";
+		reg = <0x52>;
+	};
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+
+	// Rainbow2 FRU
+	eeprom@52 {
+		compatible = "atmel,24c256";
+		reg = <0x52>;
+	};
+};
+
+&i2c9 {
+	status = "okay";
+
+	temperature-sensor@4b {
+		compatible = "ti,tmp75";
+		reg = <0x4b>;
+	};
+
+	// SCM FRU
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+
+	// BSM FRU
+	eeprom@56 {
+		compatible = "atmel,24c64";
+		reg = <0x56>;
+	};
+};
+
+&i2c10 {
+	status = "okay";
+
+	// Rainbow3 FRU
+	eeprom@52 {
+		compatible = "atmel,24c256";
+		reg = <0x52>;
+	};
+};
+
+&i2c11 {
+	status = "okay";
+
+	// OCP NIC TEMP
+	temperature-sensor@1f {
+		compatible = "ti,tmp421";
+		reg = <0x1f>;
+	};
+
+	// OCP NIC FRU
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+};
+
+&i2c12 {
+	status = "okay";
+
+	// SWB FRU
+	eeprom@52 {
+		compatible = "atmel,24c64";
+		reg = <0x52>;
+	};
+
+	i2c-mux@72 {
+		compatible = "nxp,pca9548";
+		reg = <0x72>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c12mux0ch0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			temperature-sensor@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+		};
+		i2c12mux0ch1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			power-monitor@42 {
+				compatible = "mps,mp2971";
+				reg = <0x42>;
+			};
+
+			power-monitor@43 {
+				compatible = "mps,mp2971";
+				reg = <0x43>;
+			};
+		};
+		i2c12mux0ch2: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			power-monitor@40 {
+				compatible = "ti,ina230";
+				reg = <0x40>;
+				shunt-resistor = <2000>;
+			};
+
+			power-monitor@41 {
+				compatible = "ti,ina230";
+				reg = <0x41>;
+				shunt-resistor = <2000>;
+			};
+		};
+		i2c12mux0ch3: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			power-monitor@44 {
+				compatible = "ti,ina230";
+				reg = <0x44>;
+				shunt-resistor = <2000>;
+			};
+
+			power-monitor@45 {
+				compatible = "ti,ina230";
+				reg = <0x45>;
+				shunt-resistor = <2000>;
+			};
+		};
+		i2c12mux0ch4: i2c@4 {
+			reg = <4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			voltage-sensor@49 {
+				compatible = "ti,ads7830";
+				reg = <0x49>;
+			};
+		};
+		i2c12mux0ch5: i2c@5 {
+			reg = <5>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c12mux0ch6: i2c@6 {
+			reg = <6>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+		i2c12mux0ch7: i2c@7 {
+			reg = <7>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&i2c13 {
+	status = "okay";
+
+	// Rainbow1 FRU
+	eeprom@52 {
+		compatible = "atmel,24c256";
+		reg = <0x52>;
+	};
+};
+
+&i2c14 {
+	status = "okay";
+};
+
+&i2c15 {
+	status = "okay";
+};
+
+&kcs2 {
+	aspeed,lpc-io-reg = <0xca8>;
+	status = "okay";
+};
+
+&kcs3 {
+	aspeed,lpc-io-reg = <0xca2>;
+	status = "okay";
+};
+
+&mac2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii3_default>;
+	use-ncsi;
+	status = "okay";
+};
+
+&mac3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+	use-ncsi;
+	status = "okay";
+};
+
+&sgpiom0 {
+	ngpios = <128>;
+	bus-frequency = <2000000>;
+	gpio-line-names =
+	/*in - out - in - out */
+	/*A0-A3 line 0-7*/
+	"PDB1_HSC_PWR_OK","power-chassis-control",
+	"PDB2_HSC_PWR_OK","FM_MODULE_PWRGD_0A_OUT",
+	"PWRGD_P12V_MEM","FM_MODULE_PWRGD_0B_OUT",
+	"PWRGD_P12V_SCM","FM_MODULE_PWRGD_1B_OUT",
+	/*A4-A7 line 8-15*/
+	"PWRGD_P12V_FAN","FM_MODULE_PWRGD_2B_OUT",
+	"PWRGD_P5V_AUX","FM_MODULE_PWRGD_3B_OUT",
+	"power-chassis-good","FM_MODULE_PWRGD_4B_OUT",
+	"PWRGD_P1V8_LDO","FM_CBL_PRSNT_0A_N_OUT",
+	/*B0-B3 line 16-23*/
+	"PWRGD_P1V_LDO","FM_CBL_PRSNT_0B_N_OUT",
+	"PWRGD_PVDD33_S5","FM_CBL_PRSNT_1A_N_OUT",
+	"PWRGD_PVDD18_S5_P0","FM_CBL_PRSNT_1B_N_OUT",
+	"CPU0_SLP_S5_N","FM_CBL_PRSNT_2A_N_OUT",
+	/*B4-B7 line 24-31*/
+	"PWRGD_PVDDIO_MEM_S3_P0","FM_CBL_PRSNT_2B_N_OUT",
+	"CPU0_SLP_S3_N","FM_CBL_PRSNT_3A_N_OUT",
+	"FM_MODULE_PWRGD_1B","FM_CBL_PRSNT_3B_N_OUT",
+	"FM_MODULE_PWRGD_2B","FM_CBL_PRSNT_4A_N_OUT",
+	/*C0-C3 line 32-39*/
+	"FM_MODULE_PWRGD_3B","FM_CBL_PRSNT_4B_N_OUT",
+	"FM_MODULE_PWRGD_4B","P12V_FAN0_PWRGD_OUT",
+	"FM_MODULE_PWRGD_0B","P12V_FAN1_PWRGD_OUT",
+	"PWRGD_PVDDIO_P0","P12V_FAN2_PWRGD_OUT",
+	/*C4-C7 line 40-47*/
+	"PWRGD_PVDDCR_SOC_P0","P12V_FAN3_PWRGD_OUT",
+	"PWRGD_PVDDCR_CPU0_P0","P12V_FAN4_PWRGD_OUT",
+	"PWRGD_PVDDCR_CPU1_P0","P12V_FAN5_PWRGD_OUT",
+	"FM_CPU0_PWR_GOOD","P12V_FAN6_PWRGD_OUT",
+	/*D0-D3 line 48-55*/
+	"host0-ready","P12V_FAN7_PWRGD_OUT",
+	"FM_PWRGD_CPU0_PWROK","FAN_0_PRSNT_R1_N_OUT",
+	"FM_RST_CPU0_RESETL_N","FAN_1_PRSNT_R1_N_OUT",
+	"RST_CPU0_PERST0_R_N","FAN_2_PRSNT_R1_N_OUT",
+	/*D4-D7 line 56-63*/
+	"RST_CPU0_PERST1_R_N","FAN_3_PRSNT_R1_N_OUT",
+	"BIOS_POST_CMPLT","FAN_4_PRSNT_R1_N_OUT",
+	"","FAN_5_PRSNT_R1_N_OUT",
+	"","FAN_6_PRSNT_R1_N_OUT",
+	/*E0-E3 line 64-71*/
+	"FM_PWRGD_CHAD_CPU0","FAN_7_PRSNT_R1_N_OUT",
+	"FM_PWRGD_CHEH_CPU0","TRAY_SLOT_ID0_OUT",
+	"FM_PWRGD_CHIL_CPU0","TRAY_SLOT_ID1_OUT",
+	"FM_PWRGD_CHMP_CPU0","TRAY_SLOT_ID2_OUT",
+	/*E4-E7 line 72-79*/
+	"P12V_E1S_0_PWRGD","TRAY_SLOT_ID3_OUT",
+	"P12V_E1S_1_PWRGD","TRAY_SLOT_ID4_OUT",
+	"P3V3_E1S_0_PWRGD","SCM_JTAG_MUX_S0_R",
+	"P3V3_E1S_1_PWRGD","SCM_JTAG_MUX_S1_R",
+	/*F0-F3 line 80-87*/
+	"FM_MODULE_PWRGD_0A","BMC_SGPIO_READY",
+	"OCP_V3_1_P3V3_PLD_R_PWRGD","CPU0_SYS_RESET_N",
+	"P12V_OCP_V3_1_PLD_PWRGD","RST_CPU0_KBRST_N",
+	"PWRGD_OCP_SFF_PWR_GOOD","BIOS_DEBUG_MODE",
+	/*F4-F7 line 88-95*/
+	"","CLR_CMOS",
+	"","I3C_SPD_MUX_FORCE_SEL",
+	"","FM_JTAG_HOST_SEL",
+	"","TRAY_PRESENT_N",
+	/*G0-G3 line 96-103*/
+	"MB_REV_ID_0","UART_BMC_SEL0",
+	"MB_REV_ID_1","UART_BMC_SEL1",
+	"MB_REV_ID_2","SCM_USB_SEL",
+	"MB_SKU_ID_0","FORCE_ALL_PWRON",
+	/*G4-G7 line 104-111*/
+	"MB_SKU_ID_1","PASSWORD_CLEAR",
+	"MB_SKU_ID_2","",
+	"MB_SKU_ID_3","",
+	"","BIOS_DEBUG_MODE",
+	/*H0-H3 line 112-119*/
+	"FM_IOEXP_U538_INT_N","",
+	"FM_IOEXP_U539_INT_N","",
+	"FM_IOEXP_U540_INT_N","",
+	"FM_IOEXP_U541_INT_N","",
+	/*H4-H7 line 120-127*/
+	"FM_IOEXP_PDB2_U1003_INT_N","",
+	"","","","","","",
+	/*I0-I3 line 128-135*/
+	"","","","",
+	"PDB_IRQ_PMBUS_ALERT_ISO_R_N","",
+	"PDB_UV_ALERT_ISO_R_N","",
+	/*I4-I7 line 136-143*/
+	"P12V_SCM_ADC_ALERT","",
+	"CPU0_REGS_I2C_ALERT_N","",
+	"FM_RTC_ALERT_N","",
+	"APML_CPU0_ALERT_R_N","",
+	/*J0-J3 line 144-151*/
+	"SMB_RJ45_FIO_TMP_ALERT","",
+	"FM_SMB_ALERT_MCIO_0A_N","",
+	"I3C_MCIO_0B_ALERT_ISO_R_N","",
+	"FM_SMB_ALERT_MCIO_1A_N","",
+	/*J4-J7 line 152-159*/
+	"I3C_MCIO_1B_ALERT_ISO_R_N","",
+	"FM_SMB_ALERT_MCIO_2A_N","",
+	"I3C_MCIO_2B_ALERT_ISO_R_N","",
+	"FM_SMB_ALERT_MCIO_3A_N","",
+	/*K0-K3 line 160-167*/
+	"I3C_MCIO_3B_ALERT_ISO_R_N","",
+	"FM_SMB_ALERT_MCIO_4A_N","",
+	"I3C_MCIO_4B_ALERT_ISO_R_N","",
+	"","",
+	/*K4-K7 line 168-175*/
+	"","","","","","","","",
+	/*L0-L3 line 176-183*/
+	"FM_CPU0_THERMTRIP_N","",
+	"FM_CPU0_PROCHOT_N","",
+	"FM_CPU0_SMERR_N","",
+	"FM_PVDDCR_CPU0_P0_OCP_N","",
+	/*L4-L7 line 184-191*/
+	"FM_PVDDCR_CPU1_P0_OCP_N","",
+	"FM_PVDDCR_SOC_P0_OCP_N","",
+	"FM_OCP_PWRBRK_R_N","",
+	"PMIC_ERROR_N","",
+	/*M0-M3 line 192-199*/
+	"","","","","","","","",
+	/*M4-M7 line 200-207*/
+	"","","","","","","","",
+	/*N0-N3 line 208-215*/
+	"FM_PRSNT_CPU0_N","",
+	"OCP_SFF_PRSNT_N","",
+	"E1S_0_PRSNT_R_N","",
+	"E1S_BP_0_PRSNT_R_N","",
+	/*N4-N7 line 216-223*/
+	"E1S_BP_1_PRSNT_R_N","",
+	"E1S_BP_2_PRSNT_R_N","",
+	"E1S_BP_3_PRSNT_R_N","",
+	"PDB_PRSNT_J311_N","",
+	/*O0-O3 line 224-231*/
+	"PDB_PRSNT_J312_N","",
+	"PDB_PRSNT_J313_N","",
+	"PDB_PRSNT_J314_N","",
+	"PRSNT_RJ45_FIO_N_R","",
+	/*O4-O7 line 232-239*/
+	"PRSNT_LEAK_CABLE_1_R_N","",
+	"PRSNT_LEAK_CABLE_2_R_N","",
+	"PRSNT_HDT_N","",
+	"","",
+	/*P0-P3 line 240-247*/
+	"","","","","","","","",
+	/*P4-P7 line 248-255*/
+	"","","","","","","","";
+	status = "okay";
+};
+
+// BIOS Flash
+&spi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi2_default>;
+	status = "okay";
+
+	flash@0 {
+		m25p,fast-read;
+		label = "pnor";
+		spi-max-frequency = <12000000>;
+		spi-tx-bus-width = <2>;
+		spi-rx-bus-width = <2>;
+		status = "okay";
+	};
+};
+
+// HOST BIOS Debug
+&uart1 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+// BMC Debug Console
+&uart5 {
+	status = "okay";
+};
+
+&uart_routing {
+	status = "okay";
+};
+
+&wdt1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst1_default>;
+	aspeed,reset-type = "soc";
+	aspeed,external-signal;
+	aspeed,ext-push-pull;
+	aspeed,ext-active-high;
+	aspeed,ext-pulse-duration = <256>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-tiogapass.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-tiogapass.dts
index b6b16356f571..5d4c7d979f1e 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-tiogapass.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-tiogapass.dts
@@ -211,7 +211,7 @@
 &i2c1 {
 	status = "okay";
 	//X24 Riser
-	i2c-switch@71 {
+	i2c-mux@71 {
 		compatible = "nxp,pca9544";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -243,7 +243,7 @@
 				pagesize = <32>;
 			};
 
-			i2c-switch@73 {
+			i2c-mux@73 {
 				compatible = "nxp,pca9546";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -303,7 +303,7 @@
 				pagesize = <32>;
 			};
 
-			i2c-switch@73 {
+			i2c-mux@73 {
 				compatible = "nxp,pca9546";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -363,7 +363,7 @@
 				pagesize = <32>;
 			};
 
-			i2c-switch@73 {
+			i2c-mux@73 {
 				compatible = "nxp,pca9546";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -508,7 +508,7 @@
 	status = "okay";
 	//HSC, AirMax Conn A
 	adm1278@45 {
-		compatible = "adm1275";
+		compatible = "adi,adm1275";
 		reg = <0x45>;
 		shunt-resistor-micro-ohms = <250>;
 	};
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-wedge100.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-wedge100.dts
index 584efa528450..97cd11c3d9a5 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-wedge100.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-wedge100.dts
@@ -44,7 +44,7 @@
 };
 
 &i2c7 {
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-wedge40.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-wedge40.dts
index 6624855d8ebd..6624855d8ebd 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-wedge40.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-wedge40.dts
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-wedge400.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-wedge400-data64.dts
index a901c8be49b9..1d46eaee8656 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-wedge400.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-wedge400-data64.dts
@@ -6,8 +6,8 @@
 #include "ast2500-facebook-netbmc-common.dtsi"
 
 / {
-	model = "Facebook Wedge 400 BMC";
-	compatible = "facebook,wedge400-bmc", "aspeed,ast2500";
+	model = "Facebook Wedge 400 BMC (64MB Datastore)";
+	compatible = "facebook,wedge400-data64-bmc", "aspeed,ast2500";
 
 	aliases {
 		/*
@@ -54,12 +54,12 @@
 
 	chosen {
 		stdout-path = &uart1;
-		bootargs = "console=ttyS0,9600n8 root=/dev/ram rw";
 	};
 
 	ast-adc-hwmon {
 		compatible = "iio-hwmon";
-		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>, <&adc 4>;
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>, <&adc 4>,
+			      <&adc 5>, <&adc 6>, <&adc 7>, <&adc 8>;
 	};
 
 	/*
@@ -67,20 +67,20 @@
 	 * full-duplex SPI transactions are not supported by ASPEED SPI
 	 * Controllers.
 	 */
-	spi_gpio: spi-gpio {
+	spi_gpio: spi {
 		status = "okay";
 		compatible = "spi-gpio";
 		#address-cells = <1>;
 		#size-cells = <0>;
 
 		cs-gpios = <&gpio ASPEED_GPIO(R, 2) GPIO_ACTIVE_LOW>;
-		gpio-sck = <&gpio ASPEED_GPIO(R, 3) GPIO_ACTIVE_HIGH>;
-		gpio-mosi = <&gpio ASPEED_GPIO(R, 4) GPIO_ACTIVE_HIGH>;
-		gpio-miso = <&gpio ASPEED_GPIO(R, 5) GPIO_ACTIVE_HIGH>;
+		sck-gpios = <&gpio ASPEED_GPIO(R, 3) GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio ASPEED_GPIO(R, 4) GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpio ASPEED_GPIO(R, 5) GPIO_ACTIVE_HIGH>;
 		num-chipselects = <1>;
 
-		tpmdev@0 {
-			compatible = "tcg,tpm_tis-spi";
+		tpm@0 {
+			compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
 			spi-max-frequency = <33000000>;
 			reg = <0>;
 		};
@@ -91,7 +91,7 @@
  * Both firmware flashes are 128MB on Wedge400 BMC.
  */
 &fmc_flash0 {
-#include "facebook-bmc-flash-layout-128.dtsi"
+#include "facebook-bmc-flash-layout-128-data64.dtsi"
 };
 
 &fmc_flash1 {
@@ -138,7 +138,7 @@
 &i2c2 {
 	status = "okay";
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -218,7 +218,7 @@
 &i2c8 {
 	status = "okay";
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -287,7 +287,7 @@
 &i2c11 {
 	status = "okay";
 
-	i2c-switch@76 {
+	i2c-mux@76 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -366,6 +366,7 @@
 };
 
 &sdhci1 {
+	max-frequency = <25000000>;
 	/*
 	 * DMA mode needs to be disabled to avoid conflicts with UHCI
 	 * Controller in AST2500 SoC.
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-wedge400.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-wedge400.dts
new file mode 100644
index 000000000000..ef0cfc51cda4
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-wedge400.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2019 Facebook Inc.
+
+#include "aspeed-bmc-facebook-wedge400-data64.dts"
+
+/ {
+	model = "Facebook Wedge 400 BMC";
+	compatible = "facebook,wedge400-bmc", "aspeed,ast2500";
+};
+
+&fmc_flash0 {
+	/delete-node/partitions;
+#include "facebook-bmc-flash-layout-128.dtsi"
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-yamp.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yamp.dts
index 5e6105874217..98fe0d6c8188 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-yamp.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yamp.dts
@@ -57,7 +57,7 @@
 &i2c2 {
 	status = "okay";
 
-	i2c-switch@75 {
+	i2c-mux@75 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
new file mode 100644
index 000000000000..60b98d602e80
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -0,0 +1,1384 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2022 Facebook Inc.
+
+/dts-v1/;
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/leds/leds-pca955x.h>
+#include <dt-bindings/i2c/i2c.h>
+
+/ {
+	model = "Facebook Yosemite 4 BMC";
+	compatible = "facebook,yosemite4-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial4 = &uart5;
+		serial5 = &uart6;
+		serial6 = &uart7;
+		serial7 = &uart8;
+		serial8 = &uart9;
+
+		i2c16 = &imux16;
+		i2c17 = &imux17;
+		i2c18 = &imux18;
+		i2c19 = &imux19;
+		i2c20 = &imux20;
+		i2c21 = &imux21;
+		i2c22 = &imux22;
+		i2c23 = &imux23;
+		i2c24 = &imux24;
+		i2c25 = &imux25;
+		i2c26 = &imux26;
+		i2c27 = &imux27;
+		i2c28 = &imux28;
+		i2c29 = &imux29;
+		i2c30 = &imux30;
+		i2c31 = &imux31;
+		i2c32 = &imux32;
+		i2c33 = &imux33;
+		i2c34 = &imux34;
+		i2c35 = &imux35;
+	};
+
+	chosen {
+		stdout-path = "serial4:57600n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+				<&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+				<&adc1 0>, <&adc1 1>, <&adc1 7>;
+	};
+
+	spi {
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sck-gpios = <&gpio0 ASPEED_GPIO(X, 3) GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio0 ASPEED_GPIO(X, 4) GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpio0 ASPEED_GPIO(X, 5) GPIO_ACTIVE_HIGH>;
+		cs-gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>;
+		num-chipselects = <1>;
+
+		tpm@0 {
+			compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
+			reg = <0>;
+			spi-max-frequency = <33000000>;
+		};
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&uart6 {
+	status = "okay";
+};
+
+&uart7 {
+	status = "okay";
+};
+
+&uart8 {
+	status = "okay";
+};
+
+&uart9 {
+	status = "okay";
+};
+
+&wdt1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst1_default>;
+	aspeed,reset-type = "soc";
+	aspeed,external-signal;
+	aspeed,ext-push-pull;
+	aspeed,ext-active-high;
+	aspeed,ext-pulse-duration = <256>;
+};
+
+&wdt2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst2_default>;
+	aspeed,reset-type = "system";
+};
+
+&mac2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii3_default>;
+	use-ncsi;
+	mellanox,multi-host;
+};
+
+&mac3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+	use-ncsi;
+	mellanox,multi-host;
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-tx-bus-width = <2>;
+		spi-rx-bus-width = <2>;
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-128.dtsi"
+	};
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "alt-bmc";
+		spi-tx-bus-width = <2>;
+		spi-rx-bus-width = <2>;
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+	mctp-controller;
+	bus-frequency = <400000>;
+	multi-master;
+
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	gpio@21 {
+		compatible = "nxp,pca9506";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio@22 {
+		compatible = "nxp,pca9506";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "SLOT1_UART_SEL0","SLOT1_UART_SEL1",
+				"SLOT1_UART_SEL2","","","","","",
+				"","","","","","","","",
+				"","","","","","","","",
+				"","","","","","","","";
+	};
+
+	gpio@23 {
+		compatible = "nxp,pca9506";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio@24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	power-sensor@40 {
+		compatible = "adi,adm1281";
+		reg = <0x40>;
+		shunt-resistor-micro-ohms = <500>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	mctp-controller;
+	bus-frequency = <400000>;
+	multi-master;
+
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	gpio@21 {
+		compatible = "nxp,pca9506";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio@22 {
+		compatible = "nxp,pca9506";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "SLOT2_UART_SEL0","SLOT2_UART_SEL1",
+				"SLOT2_UART_SEL2","","","","","",
+				"","","","","","","","",
+				"","","","","","","","",
+				"","","","","","","","";
+	};
+
+	gpio@23 {
+		compatible = "nxp,pca9506";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio@24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	power-sensor@40 {
+		compatible = "adi,adm1281";
+		reg = <0x40>;
+		shunt-resistor-micro-ohms = <500>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+	mctp-controller;
+	bus-frequency = <400000>;
+	multi-master;
+
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	gpio@21 {
+		compatible = "nxp,pca9506";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio@22 {
+		compatible = "nxp,pca9506";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "SLOT3_UART_SEL0","SLOT3_UART_SEL1",
+				"SLOT3_UART_SEL2","","","","","",
+				"","","","","","","","",
+				"","","","","","","","",
+				"","","","","","","","";
+	};
+
+	gpio@23 {
+		compatible = "nxp,pca9506";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio@24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	power-sensor@40 {
+		compatible = "adi,adm1281";
+		reg = <0x40>;
+		shunt-resistor-micro-ohms = <500>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+	mctp-controller;
+	bus-frequency = <400000>;
+	multi-master;
+
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	gpio@21 {
+		compatible = "nxp,pca9506";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio@22 {
+		compatible = "nxp,pca9506";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "SLOT4_UART_SEL0","SLOT4_UART_SEL1",
+				"SLOT4_UART_SEL2","","","","","",
+				"","","","","","","","",
+				"","","","","","","","",
+				"","","","","","","","";
+	};
+
+	gpio@23 {
+		compatible = "nxp,pca9506";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio@24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	power-sensor@40 {
+		compatible = "adi,adm1281";
+		reg = <0x40>;
+		shunt-resistor-micro-ohms = <500>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+	mctp-controller;
+	bus-frequency = <400000>;
+	multi-master;
+
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	gpio@21 {
+		compatible = "nxp,pca9506";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio@22 {
+		compatible = "nxp,pca9506";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "SLOT5_UART_SEL0","SLOT5_UART_SEL1",
+				"SLOT5_UART_SEL2","","","","","",
+				"","","","","","","","",
+				"","","","","","","","",
+				"","","","","","","","";
+	};
+
+	gpio@23 {
+		compatible = "nxp,pca9506";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio@24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	power-sensor@40 {
+		compatible = "adi,adm1281";
+		reg = <0x40>;
+		shunt-resistor-micro-ohms = <500>;
+	};
+};
+
+&i2c5 {
+	status = "okay";
+	mctp-controller;
+	bus-frequency = <400000>;
+	multi-master;
+
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	gpio@21 {
+		compatible = "nxp,pca9506";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio@22 {
+		compatible = "nxp,pca9506";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "SLOT6_UART_SEL0","SLOT6_UART_SEL1",
+				"SLOT6_UART_SEL2","","","","","",
+				"","","","","","","","",
+				"","","","","","","","",
+				"","","","","","","","";
+	};
+
+	gpio@23 {
+		compatible = "nxp,pca9506";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio@24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	power-sensor@40 {
+		compatible = "adi,adm1281";
+		reg = <0x40>;
+		shunt-resistor-micro-ohms = <500>;
+	};
+};
+
+&i2c6 {
+	status = "okay";
+	mctp-controller;
+	bus-frequency = <400000>;
+	multi-master;
+
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	gpio@21 {
+		compatible = "nxp,pca9506";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio@22 {
+		compatible = "nxp,pca9506";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "SLOT7_UART_SEL0","SLOT7_UART_SEL1",
+				"SLOT7_UART_SEL2","","","","","",
+				"","","","","","","","",
+				"","","","","","","","",
+				"","","","","","","","";
+	};
+
+	gpio@23 {
+		compatible = "nxp,pca9506";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio@24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	power-sensor@40 {
+		compatible = "adi,adm1281";
+		reg = <0x40>;
+		shunt-resistor-micro-ohms = <500>;
+	};
+};
+
+&i2c7 {
+	status = "okay";
+	mctp-controller;
+	bus-frequency = <400000>;
+	multi-master;
+
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	gpio@21 {
+		compatible = "nxp,pca9506";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio@22 {
+		compatible = "nxp,pca9506";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "SLOT8_UART_SEL0","SLOT8_UART_SEL1",
+				"SLOT8_UART_SEL2","","","","","",
+				"","","","","","","","",
+				"","","","","","","","",
+				"","","","","","","","";
+	};
+
+	gpio@23 {
+		compatible = "nxp,pca9506";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio@24 {
+		compatible = "nxp,pca9506";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	power-sensor@40 {
+		compatible = "adi,adm1281";
+		reg = <0x40>;
+		shunt-resistor-micro-ohms = <500>;
+	};
+};
+
+&i2c8 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+	bus-frequency = <400000>;
+	i2c-mux@70 {
+		compatible = "nxp,pca9544";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		imux16: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			gpio@49 {
+				compatible = "nxp,pca9537";
+				reg = <0x49>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			eeprom@50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			eeprom@51 {
+				compatible = "atmel,24c128";
+				reg = <0x51>;
+			};
+
+			eeprom@54 {
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
+
+		imux17: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			gpio@49 {
+				compatible = "nxp,pca9537";
+				reg = <0x49>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			eeprom@50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			eeprom@51 {
+				compatible = "atmel,24c128";
+				reg = <0x51>;
+			};
+
+			eeprom@54 {
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
+
+		imux18: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			gpio@49 {
+				compatible = "nxp,pca9537";
+				reg = <0x49>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			eeprom@50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			eeprom@51 {
+				compatible = "atmel,24c128";
+				reg = <0x51>;
+			};
+
+			eeprom@54 {
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
+
+		imux19: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			gpio@49 {
+				compatible = "nxp,pca9537";
+				reg = <0x49>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			eeprom@50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			eeprom@51 {
+				compatible = "atmel,24c128";
+				reg = <0x51>;
+			};
+
+			eeprom@54 {
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
+	};
+};
+
+&i2c9 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+	bus-frequency = <400000>;
+	i2c-mux@71 {
+		compatible = "nxp,pca9544";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		imux20: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			gpio@49 {
+				compatible = "nxp,pca9537";
+				reg = <0x49>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			eeprom@50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			eeprom@51 {
+				compatible = "atmel,24c128";
+				reg = <0x51>;
+			};
+
+			eeprom@54 {
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
+
+		imux21: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			gpio@49 {
+				compatible = "nxp,pca9537";
+				reg = <0x49>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			eeprom@50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			eeprom@51 {
+				compatible = "atmel,24c128";
+				reg = <0x51>;
+			};
+
+			eeprom@54 {
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
+
+		imux22: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			gpio@49 {
+				compatible = "nxp,pca9537";
+				reg = <0x49>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			eeprom@50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			eeprom@51 {
+				compatible = "atmel,24c128";
+				reg = <0x51>;
+			};
+
+			eeprom@54 {
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
+
+		imux23: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			gpio@49 {
+				compatible = "nxp,pca9537";
+				reg = <0x49>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			eeprom@50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			eeprom@51 {
+				compatible = "atmel,24c128";
+				reg = <0x51>;
+			};
+
+			eeprom@54 {
+				compatible = "atmel,24c128";
+				reg = <0x54>;
+			};
+		};
+	};
+};
+
+&i2c10 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+	bus-frequency = <400000>;
+	i2c-mux@74 {
+		compatible = "nxp,pca9544";
+		reg = <0x74>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		imux28: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			gpio@20 {
+				compatible = "nxp,pca9506";
+				reg = <0x20>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio@21 {
+				compatible = "nxp,pca9506";
+				reg = <0x21>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio@22 {
+				compatible = "nxp,pca9506";
+				reg = <0x22>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio@23 {
+				compatible = "nxp,pca9506";
+				reg = <0x23>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio@24 {
+				compatible = "nxp,pca9506";
+				reg = <0x24>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				gpio-line-names = "","","","",
+						  "NIC0_MAIN_PWR_EN",
+						  "NIC1_MAIN_PWR_EN",
+						  "NIC2_MAIN_PWR_EN",
+						  "NIC3_MAIN_PWR_EN",
+						  "","","","","","","","",
+						  "","","","","","","","",
+						  "","","","","","","","";
+			};
+		};
+
+		imux29: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&i2c11 {
+	status = "okay";
+	power-sensor@10 {
+		compatible = "adi,adm1272";
+		reg = <0x10>;
+	};
+
+	power-sensor@12 {
+		compatible = "adi,adm1272";
+		reg = <0x12>;
+	};
+
+	gpio@20 {
+		compatible = "nxp,pca9555";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <98 IRQ_TYPE_LEVEL_LOW>;
+		gpio-line-names = "P48V_OCP_GPIO1", "P48V_OCP_GPIO2",
+				  "P48V_OCP_GPIO3", "FAN_BOARD_0_REVISION_0_R",
+				  "FAN_BOARD_0_REVISION_1_R",
+				  "FAN_BOARD_1_REVISION_0_R",
+				  "FAN_BOARD_1_REVISION_1_R", "RST_MUX_R_N",
+				  "RST_LED_CONTROL_FAN_BOARD_0_N",
+				  "RST_LED_CONTROL_FAN_BOARD_1_N",
+				  "RST_IOEXP_FAN_BOARD_0_N",
+				  "RST_IOEXP_FAN_BOARD_1_N",
+				  "PWRGD_LOAD_SWITCH_FAN_BOARD_0_R",
+				  "PWRGD_LOAD_SWITCH_FAN_BOARD_1_R",
+				  "", "";
+	};
+
+	gpio@21 {
+		compatible = "nxp,pca9555";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <98 IRQ_TYPE_LEVEL_LOW>;
+		gpio-line-names = "HSC_OCP_SLOT_ODD_GPIO1",
+				  "HSC_OCP_SLOT_ODD_GPIO2",
+				  "HSC_OCP_SLOT_ODD_GPIO3",
+				  "HSC_OCP_SLOT_EVEN_GPIO1",
+				  "HSC_OCP_SLOT_EVEN_GPIO2",
+				  "HSC_OCP_SLOT_EVEN_GPIO3",
+				  "ADC_TYPE_0_R", "ADC_TYPE_1_R",
+				  "MEDUSA_BOARD_REV_0", "MEDUSA_BOARD_REV_1",
+				  "MEDUSA_BOARD_REV_2", "MEDUSA_BOARD_TYPE",
+				  "DELTA_MODULE_TYPE", "P12V_HSC_TYPE",
+				  "", "";
+	};
+
+	gpio@22 {
+		compatible = "nxp,pca9555";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <98 IRQ_TYPE_LEVEL_LOW>;
+		gpio-line-names = "CARD_TYPE_SLOT1", "CARD_TYPE_SLOT2",
+				  "CARD_TYPE_SLOT3", "CARD_TYPE_SLOT4",
+				  "CARD_TYPE_SLOT5", "CARD_TYPE_SLOT6",
+				  "CARD_TYPE_SLOT7", "CARD_TYPE_SLOT8",
+				  "OC_P48V_HSC_0_N", "FLT_P48V_HSC_0_N",
+				  "OC_P48V_HSC_1_N", "FLT_P48V_HSC_1_N",
+				  "EN_P48V_AUX_0", "EN_P48V_AUX_1",
+				  "PWRGD_P12V_AUX_0", "PWRGD_P12V_AUX_1";
+	};
+
+	gpio@23 {
+		compatible = "nxp,pca9555";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <98 IRQ_TYPE_LEVEL_LOW>;
+		gpio-line-names = "HSC1_ALERT1_R_N", "HSC2_ALERT1_R_N",
+				  "HSC3_ALERT1_R_N", "HSC4_ALERT1_R_N",
+				  "HSC5_ALERT1_R_N", "HSC6_ALERT1_R_N",
+				  "HSC7_ALERT1_R_N", "HSC8_ALERT1_R_N",
+				  "HSC1_ALERT2_R_N", "HSC2_ALERT2_R_N",
+				  "HSC3_ALERT2_R_N", "HSC4_ALERT2_R_N",
+				  "HSC5_ALERT2_R_N", "HSC6_ALERT2_R_N",
+				  "HSC7_ALERT2_R_N", "HSC8_ALERT2_R_N";
+	};
+
+	temperature-sensor@48 {
+		compatible = "ti,tmp75";
+		reg = <0x48>;
+	};
+
+	temperature-sensor@49 {
+		compatible = "ti,tmp75";
+		reg = <0x49>;
+	};
+
+	eeprom@54 {
+		compatible = "atmel,24c128";
+		reg = <0x54>;
+	};
+};
+
+&i2c12 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+	bus-frequency = <400000>;
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9544";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		imux34: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			temperature-sensor@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+
+			eeprom@50 {
+				compatible = "atmel,24c128";
+				reg = <0x50>;
+			};
+
+			eeprom@54 {
+				compatible = "atmel,24c64";
+				reg = <0x54>;
+			};
+
+			rtc@6f {
+				compatible = "nuvoton,nct3018y";
+				reg = <0x6f>;
+			};
+
+			gpio@20 {
+				compatible = "nxp,pca9506";
+				reg = <0x20>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio@21 {
+				compatible = "nxp,pca9506";
+				reg = <0x21>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio@22 {
+				compatible = "nxp,pca9506";
+				reg = <0x22>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio@23 {
+				compatible = "nxp,pca9506";
+				reg = <0x23>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+		};
+
+		imux35: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&i2c13 {
+	status = "okay";
+	bus-frequency = <100000>;
+	multi-master;
+
+	ipmb@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
+};
+
+&i2c14 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+	bus-frequency = <400000>;
+	adc@1d {
+		compatible = "ti,adc128d818";
+		reg = <0x1d>;
+		ti,mode = /bits/ 8 <1>;
+	};
+
+	adc@36 {
+		compatible = "ti,adc128d818";
+		reg = <0x36>;
+		ti,mode = /bits/ 8 <1>;
+	};
+
+	adc@37 {
+		compatible = "ti,adc128d818";
+		reg = <0x37>;
+		ti,mode = /bits/ 8 <1>;
+	};
+
+	power-sensor@40 {
+		compatible = "ti,ina230";
+		reg = <0x40>;
+	};
+
+	power-sensor@41 {
+		compatible = "ti,ina230";
+		reg = <0x41>;
+	};
+
+	power-sensor@42 {
+		compatible = "ti,ina230";
+		reg = <0x42>;
+	};
+
+	power-sensor@43 {
+		compatible = "ti,ina230";
+		reg = <0x43>;
+	};
+
+	power-sensor@44 {
+		compatible = "ti,ina230";
+		reg = <0x44>;
+	};
+
+	temperature-sensor@4e {
+		compatible = "ti,tmp75";
+		reg = <0x4e>;
+	};
+
+	temperature-sensor@4f {
+		compatible = "ti,tmp75";
+		reg = <0x4f>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+	};
+
+	i2c-mux@73 {
+		compatible = "nxp,pca9544";
+		reg = <0x73>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		imux32: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			adc@35 {
+				compatible = "maxim,max11617";
+				reg = <0x35>;
+			};
+		};
+
+		imux33: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			adc@35 {
+				compatible = "maxim,max11617";
+				reg = <0x35>;
+			};
+		};
+	};
+
+	i2c-mux@74 {
+		compatible = "nxp,pca9546";
+		reg = <0x74>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		imux30: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			adc@1f {
+				compatible = "ti,adc128d818";
+				reg = <0x1f>;
+				ti,mode = /bits/ 8 <1>;
+			};
+
+			pwm@20 {
+				compatible = "maxim,max31790";
+				reg = <0x20>;
+			};
+
+			gpio@22 {
+				compatible = "ti,tca6424";
+				reg = <0x22>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			pwm@2f {
+				compatible = "maxim,max31790";
+				reg = <0x2f>;
+			};
+
+			adc@33 {
+				compatible = "maxim,max11615";
+				reg = <0x33>;
+			};
+
+			eeprom@52 {
+				compatible = "atmel,24c128";
+				reg = <0x52>;
+			};
+
+			gpio@61 {
+				compatible = "nxp,pca9552";
+				reg = <0x61>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+		};
+
+		imux31: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			adc@1f {
+				compatible = "ti,adc128d818";
+				reg = <0x1f>;
+				ti,mode = /bits/ 8 <1>;
+			};
+
+			pwm@20 {
+				compatible = "maxim,max31790";
+				reg = <0x20>;
+			};
+
+			gpio@22 {
+				compatible = "ti,tca6424";
+				reg = <0x22>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			pwm@2f {
+				compatible = "maxim,max31790";
+				reg = <0x2f>;
+			};
+
+			adc@33 {
+				compatible = "maxim,max11615";
+				reg = <0x33>;
+			};
+
+			eeprom@52 {
+				compatible = "atmel,24c128";
+				reg = <0x52>;
+			};
+
+			gpio@61 {
+				compatible = "nxp,pca9552";
+				reg = <0x61>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+		};
+	};
+};
+
+&i2c15 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+	multi-master;
+	bus-frequency = <400000>;
+
+	mctp@10 {
+		compatible = "mctp-i2c-controller";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	i2c-mux@72 {
+		compatible = "nxp,pca9544";
+		reg = <0x72>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		imux24: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			mctp-controller;
+			temperature-sensor@1f {
+				compatible = "ti,tmp421";
+				reg = <0x1f>;
+			};
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		imux25: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			mctp-controller;
+			temperature-sensor@1f {
+				compatible = "ti,tmp421";
+				reg = <0x1f>;
+			};
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		imux26: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			mctp-controller;
+			temperature-sensor@1f {
+				compatible = "ti,tmp421";
+				reg = <0x1f>;
+			};
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		imux27: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			mctp-controller;
+			temperature-sensor@1f {
+				compatible = "ti,tmp421";
+				reg = <0x1f>;
+			};
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+	};
+};
+
+&adc0 {
+	status = "okay";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+			&pinctrl_adc2_default &pinctrl_adc3_default
+			&pinctrl_adc4_default &pinctrl_adc5_default
+			&pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+	status = "okay";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+			&pinctrl_adc15_default>;
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&uhci {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-yosemitev2.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemitev2.dts
index 8864e9c312a8..5143f85fbd70 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-yosemitev2.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemitev2.dts
@@ -95,7 +95,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_rmii1_default>;
 	use-ncsi;
-	mlx,multi-host;
+	mellanox,multi-host;
 };
 
 &adc {
@@ -207,11 +207,16 @@
 
 &i2c12 {
 	status = "okay";
-	//MEZZ_FRU
-	eeprom@51 {
-		compatible = "atmel,24c64";
-		reg = <0x51>;
-		pagesize = <32>;
+};
+
+&i2c13 {
+	status = "okay";
+	// Debug Card
+	multi-master;
+	ipmb13@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
 	};
 };
 
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge-4u.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge-4u.dts
new file mode 100644
index 000000000000..839aad4ddd91
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge-4u.dts
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2024 IBM Corp.
+/dts-v1/;
+
+#include "aspeed-bmc-ibm-blueridge.dts"
+
+/ {
+	model = "Blueridge 4U";
+};
+
+&i2c3 {
+	power-supply@6a {
+		compatible = "ibm,cffps";
+		reg = <0x6a>;
+	};
+
+	power-supply@6b {
+		compatible = "ibm,cffps";
+		reg = <0x6b>;
+	};
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts
new file mode 100644
index 000000000000..bc4c46235421
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-blueridge.dts
@@ -0,0 +1,1688 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2024 IBM Corp.
+/dts-v1/;
+
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/leds/leds-pca955x.h>
+#include "aspeed-g6.dtsi"
+#include "ibm-power11-quad.dtsi"
+
+/ {
+	model = "Blueridge 2U";
+	compatible = "ibm,blueridge-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial4 = &uart5;
+		i2c16 = &i2c2mux0;
+		i2c17 = &i2c2mux1;
+		i2c18 = &i2c2mux2;
+		i2c19 = &i2c2mux3;
+		i2c20 = &i2c4mux0chn0;
+		i2c21 = &i2c4mux0chn1;
+		i2c22 = &i2c4mux0chn2;
+		i2c23 = &i2c5mux0chn0;
+		i2c24 = &i2c5mux0chn1;
+		i2c25 = &i2c6mux0chn0;
+		i2c26 = &i2c6mux0chn1;
+		i2c27 = &i2c6mux0chn2;
+		i2c28 = &i2c6mux0chn3;
+		i2c29 = &i2c11mux0chn0;
+		i2c30 = &i2c11mux0chn1;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		event_log: region@b3d00000 {
+			reg = <0xb3d00000 0x100000>;
+			no-map;
+		};
+
+		ramoops@b3e00000 {
+			compatible = "ramoops";
+			reg = <0xb3e00000 0x200000>; /* 16 * (4 * 0x8000) */
+			record-size = <0x8000>;
+			console-size = <0x8000>;
+			ftrace-size = <0x8000>;
+			pmsg-size = <0x8000>;
+			max-reason = <3>; /* KMSG_DUMP_EMERG */
+		};
+
+		/* LPC FW cycle bridge region requires natural alignment */
+		flash_memory: region@b4000000 {
+			reg = <0xb4000000 0x04000000>; /* 64M */
+			no-map;
+		};
+
+		/* VGA region is dictated by hardware strapping */
+		vga_memory: region@bf000000 {
+			compatible = "shared-dma-pool";
+			reg = <0xbf000000 0x01000000>;  /* 16M */
+			no-map;
+		};
+	};
+
+	i2c-mux {
+		compatible = "i2c-mux-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-parent = <&i2c2>;
+		idle-state = <0>;
+		mux-gpios = <&gpio0 ASPEED_GPIO(G, 4) GPIO_ACTIVE_HIGH>,
+			    <&gpio0 ASPEED_GPIO(G, 5) GPIO_ACTIVE_HIGH>;
+
+		i2c2mux0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c2mux1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c2mux2: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c2mux3: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		/* BMC Card fault LED at the back */
+		led-bmc-ingraham0 {
+			gpios = <&gpio0 ASPEED_GPIO(H, 1) GPIO_ACTIVE_LOW>;
+		};
+
+		/* Enclosure ID LED at the back */
+		led-rear-enc-id0 {
+			gpios = <&gpio0 ASPEED_GPIO(H, 2) GPIO_ACTIVE_LOW>;
+		};
+
+		/* Enclosure fault LED at the back */
+		led-rear-enc-fault0 {
+			gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>;
+		};
+
+		/* PCIE slot power LED */
+		led-pcieslot-power {
+			gpios = <&gpio0 ASPEED_GPIO(P, 4) GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		poll-interval = <1000>;
+
+		event-fan0-presence {
+			gpios = <&pca0 6 GPIO_ACTIVE_LOW>;
+			label = "fan0-presence";
+			linux,code = <6>;
+		};
+
+		event-fan1-presence {
+			gpios = <&pca0 7 GPIO_ACTIVE_LOW>;
+			label = "fan1-presence";
+			linux,code = <7>;
+		};
+
+		event-fan2-presence {
+			gpios = <&pca0 8 GPIO_ACTIVE_LOW>;
+			label = "fan2-presence";
+			linux,code = <8>;
+		};
+
+		event-fan3-presence {
+			gpios = <&pca0 9 GPIO_ACTIVE_LOW>;
+			label = "fan3-presence";
+			linux,code = <9>;
+		};
+
+		event-fan4-presence {
+			gpios = <&pca0 10 GPIO_ACTIVE_LOW>;
+			label = "fan4-presence";
+			linux,code = <10>;
+		};
+
+		event-fan5-presence {
+			gpios = <&pca0 11 GPIO_ACTIVE_LOW>;
+			label = "fan5-presence";
+			linux,code = <11>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc1 7>;
+	};
+};
+
+&adc1 {
+	status = "okay";
+	aspeed,int-vref-microvolt = <2500000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+		&pinctrl_adc10_default &pinctrl_adc11_default
+		&pinctrl_adc12_default &pinctrl_adc13_default
+		&pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&uhci {
+	status = "okay";
+};
+
+&gpio0 {
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","","","",
+	/*B0-B7*/	"bmc-management-ready","","","","","","checkstop","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"","","","","","","","",
+	/*F0-F7*/	"","","rtc-battery-voltage-read-enable","reset-cause-pinhole","","",
+			"factory-reset-toggle","",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"","led-bmc-ingraham0","led-rear-enc-id0","led-rear-enc-fault0","","","",
+			"",
+	/*I0-I7*/	"","","","","","","bmc-secure-boot","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","usb-power","","","","",
+	/*P0-P7*/	"","","","","led-pcieslot-power","","","",
+	/*Q0-Q7*/	"cfam-reset","","regulator-standby-faulted","","","","","",
+	/*R0-R7*/	"bmc-tpm-reset","power-chassis-control","power-chassis-good","","","","",
+			"",
+	/*S0-S7*/	"presence-ps0","presence-ps1","presence-ps2","presence-ps3",
+			"power-ffs-sync-history","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"","","","","","","","";
+
+	i2c3-mux-oe-n-hog {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(G, 6) GPIO_ACTIVE_LOW>;
+		line-name = "I2C3_MUX_OE_N";
+		output-high;
+	};
+
+	usb-power-hog {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(O, 3) GPIO_ACTIVE_LOW>;
+		output-high;
+	};
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&pinctrl_emmc_default {
+	bias-disable;
+};
+
+&emmc {
+	status = "okay";
+	clk-phase-mmc-hs200 = <180>, <180>;
+};
+
+&ibt {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	eeprom@51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+
+	gpio@20 {
+		compatible = "ti,tca9554";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names = "",
+			"RUSSEL_FW_I2C_ENABLE_N",
+			"RUSSEL_OPPANEL_PRESENCE_N",
+			"BLYTH_OPPANEL_PRESENCE_N",
+			"CPU_TPM_CARD_PRESENT_N",
+			"DASD_BP2_PRESENT_N",
+			"DASD_BP1_PRESENT_N",
+			"DASD_BP0_PRESENT_N";
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+
+	power-supply@68 {
+		compatible = "ibm,cffps";
+		reg = <0x68>;
+	};
+
+	power-supply@69 {
+		compatible = "ibm,cffps";
+		reg = <0x69>;
+	};
+
+	led-controller@61 {
+		compatible = "nxp,pca9552";
+		reg = <0x61>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"SLOT0_PRSNT_EN_RSVD", "SLOT1_PRSNT_EN_RSVD",
+			"SLOT2_PRSNT_EN_RSVD", "SLOT3_PRSNT_EN_RSVD",
+			"SLOT4_PRSNT_EN_RSVD", "SLOT0_EXPANDER_PRSNT_N",
+			"SLOT1_EXPANDER_PRSNT_N", "SLOT2_EXPANDER_PRSNT_N",
+			"SLOT3_EXPANDER_PRSNT_N", "SLOT4_EXPANDER_PRSNT_N",
+			"", "", "", "", "", "";
+	};
+};
+
+&i2c4 {
+	status = "okay";
+
+	temperature-sensor@48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	temperature-sensor@49 {
+		compatible = "ti,tmp275";
+		reg = <0x49>;
+	};
+
+	temperature-sensor@4a {
+		compatible = "ti,tmp275";
+		reg = <0x4a>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c4mux0chn0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+
+			led-controller@60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					reg = <0>;
+					default-state = "keep";
+					label = "cablecard0-cxp-top";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					reg = <1>;
+					default-state = "keep";
+					label = "cablecard0-cxp-bot";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c4mux0chn1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+		};
+
+		i2c4mux0chn2: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@52 {
+				compatible = "atmel,24c64";
+				reg = <0x52>;
+			};
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	temperature-sensor@48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	temperature-sensor@49 {
+		compatible = "ti,tmp275";
+		reg = <0x49>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c5mux0chn0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+
+			led-controller@60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					reg = <0>;
+					default-state = "keep";
+					label = "cablecard3-cxp-top";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					reg = <1>;
+					default-state = "keep";
+					label = "cablecard3-cxp-bot";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c5mux0chn1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+
+			led-controller@61 {
+				compatible = "nxp,pca9551";
+				reg = <0x61>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					reg = <0>;
+					default-state = "keep";
+					label = "cablecard4-cxp-top";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					reg = <1>;
+					default-state = "keep";
+					label = "cablecard4-cxp-bot";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+	};
+};
+
+&i2c6 {
+	status = "okay";
+
+	temperature-sensor@48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	temperature-sensor@4a {
+		compatible = "ti,tmp275";
+		reg = <0x4a>;
+	};
+
+	temperature-sensor@4b {
+		compatible = "ti,tmp275";
+		reg = <0x4b>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c6mux0chn0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c6mux0chn1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@52 {
+				compatible = "atmel,24c64";
+				reg = <0x52>;
+			};
+		};
+
+		i2c6mux0chn2: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		i2c6mux0chn3: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+		};
+	};
+};
+
+&i2c7 {
+	multi-master;
+	status = "okay";
+
+	led-controller@30 {
+		compatible = "ibm,pca9552";
+		reg = <0x30>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			reg = <0>;
+			default-state = "keep";
+			label = "pcieslot0";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			reg = <1>;
+			default-state = "keep";
+			label = "pcieslot1";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			reg = <2>;
+			default-state = "keep";
+			label = "pcieslot2";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			reg = <3>;
+			default-state = "keep";
+			label = "pcieslot3";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			reg = <4>;
+			default-state = "keep";
+			label = "pcieslot4";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			reg = <5>;
+			default-state = "keep";
+			label = "cpu1";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			reg = <6>;
+			default-state = "keep";
+			label = "cpu-vrm1";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			reg = <8>;
+			default-state = "keep";
+			label = "lcd-russel";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	led-controller@31 {
+		compatible = "ibm,pca9552";
+		reg = <0x31>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			reg = <0>;
+			default-state = "keep";
+			label = "ddimm0";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			reg = <1>;
+			default-state = "keep";
+			label = "ddimm1";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			reg = <2>;
+			default-state = "keep";
+			label = "ddimm2";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			reg = <3>;
+			default-state = "keep";
+			label = "ddimm3";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			reg = <4>;
+			default-state = "keep";
+			label = "ddimm4";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			reg = <5>;
+			default-state = "keep";
+			label = "ddimm5";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			reg = <6>;
+			default-state = "keep";
+			label = "ddimm6";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			reg = <7>;
+			default-state = "keep";
+			label = "ddimm7";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			reg = <8>;
+			default-state = "keep";
+			label = "ddimm8";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			reg = <9>;
+			default-state = "keep";
+			label = "ddimm9";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@a {
+			reg = <10>;
+			default-state = "keep";
+			label = "ddimm10";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@b {
+			reg = <11>;
+			default-state = "keep";
+			label = "ddimm11";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@c {
+			reg = <12>;
+			default-state = "keep";
+			label = "ddimm12";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@d {
+			reg = <13>;
+			default-state = "keep";
+			label = "ddimm13";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@e {
+			reg = <14>;
+			default-state = "keep";
+			label = "ddimm14";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@f {
+			reg = <15>;
+			default-state = "keep";
+			label = "ddimm15";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	led-controller@32 {
+		compatible = "ibm,pca9552";
+		reg = <0x32>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			reg = <0>;
+			default-state = "keep";
+			label = "ddimm16";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			reg = <1>;
+			default-state = "keep";
+			label = "ddimm17";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			reg = <2>;
+			default-state = "keep";
+			label = "ddimm18";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			reg = <3>;
+			default-state = "keep";
+			label = "ddimm19";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			reg = <4>;
+			default-state = "keep";
+			label = "ddimm20";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			reg = <5>;
+			default-state = "keep";
+			label = "ddimm21";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			reg = <6>;
+			default-state = "keep";
+			label = "ddimm22";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			reg = <7>;
+			default-state = "keep";
+			label = "ddimm23";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			reg = <8>;
+			default-state = "keep";
+			label = "ddimm24";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			reg = <9>;
+			default-state = "keep";
+			label = "ddimm25";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@a {
+			reg = <10>;
+			default-state = "keep";
+			label = "ddimm26";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@b {
+			reg = <11>;
+			default-state = "keep";
+			label = "ddimm27";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@c {
+			reg = <12>;
+			default-state = "keep";
+			label = "ddimm28";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@d {
+			reg = <13>;
+			default-state = "keep";
+			label = "ddimm29";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@e {
+			reg = <14>;
+			default-state = "keep";
+			label = "ddimm30";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@f {
+			reg = <15>;
+			default-state = "keep";
+			label = "ddimm31";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	led-controller@33 {
+		compatible = "ibm,pca9552";
+		reg = <0x33>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			reg = <0>;
+			default-state = "keep";
+			label = "planar";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			reg = <1>;
+			default-state = "keep";
+			label = "cpu0";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			reg = <3>;
+			default-state = "keep";
+			label = "dasd-pyramid0";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			reg = <4>;
+			default-state = "keep";
+			label = "dasd-pyramid1";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			reg = <5>;
+			default-state = "keep";
+			label = "dasd-pyramid2";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			reg = <6>;
+			default-state = "keep";
+			label = "cpu0-vrm0";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			reg = <7>;
+			default-state = "keep";
+			label = "rtc-battery";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			reg = <8>;
+			default-state = "keep";
+			label = "base-blyth";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			reg = <9>;
+			default-state = "keep";
+			label = "pcieslot6";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@a {
+			reg = <10>;
+			default-state = "keep";
+			label = "pcieslot7";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@b {
+			reg = <11>;
+			default-state = "keep";
+			label = "pcieslot8";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@c {
+			reg = <12>;
+			default-state = "keep";
+			label = "pcieslot9";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@d {
+			reg = <13>;
+			default-state = "keep";
+			label = "pcieslot10";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@e {
+			reg = <14>;
+			default-state = "keep";
+			label = "pcieslot11";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@f {
+			reg = <15>;
+			default-state = "keep";
+			label = "tpm-wilson";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	humidity-sensor@40 {
+		compatible = "silabs,si7020";
+		reg = <0x40>;
+	};
+
+	temperature-sensor@48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	pwm@52 {
+		compatible = "maxim,max31785a";
+		reg = <0x52>;
+	};
+
+	led-controller@60 {
+		compatible = "nxp,pca9551";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			reg = <0>;
+			default-state = "keep";
+			label = "front-sys-id0";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			reg = <1>;
+			default-state = "keep";
+			label = "front-check-log0";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			reg = <2>;
+			default-state = "keep";
+			label = "front-enc-fault1";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			reg = <3>;
+			default-state = "keep";
+			label = "front-sys-pwron0";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	pca0: led-controller@61 {
+		compatible = "nxp,pca9552";
+		reg = <0x61>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			reg = <0>;
+			default-state = "keep";
+			label = "fan0";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			reg = <1>;
+			default-state = "keep";
+			label = "fan1";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			reg = <2>;
+			default-state = "keep";
+			label = "fan2";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			reg = <3>;
+			default-state = "keep";
+			label = "fan3";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			reg = <4>;
+			default-state = "keep";
+			label = "fan4";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			reg = <5>;
+			default-state = "keep";
+			label = "fan5";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	lcd-controller@62 {
+		compatible = "ibm,op-panel";
+		reg = <(0x62 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	pressure-sensor@76 {
+		compatible = "infineon,dps310";
+		reg = <0x76>;
+		#io-channel-cells = <0>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+};
+
+&i2c8 {
+	status = "okay";
+
+	pmic@11 {
+		compatible = "ti,ucd90320";
+		reg = <0x11>;
+	};
+
+	rtc@32 {
+		compatible = "epson,rx8900";
+		reg = <0x32>;
+	};
+
+	temperature-sensor@48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	temperature-sensor@4a {
+		compatible = "ti,tmp275";
+		reg = <0x4a>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+
+	led-controller@60 {
+		compatible = "nxp,pca9552";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"", "", "", "", "", "", "P10_DCM0_PRES", "P10_DCM1_PRES",
+			"", "", "", "", "PRESENT_VRM_DCM0_N", "PRESENT_VRM_DCM1_N",
+			"power-config-full-load", "";
+	};
+
+	led-controller@61 {
+		compatible = "nxp,pca9552";
+		reg = <0x61>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"SLOT6_PRSNT_EN_RSVD", "SLOT7_PRSNT_EN_RSVD",
+			"SLOT8_PRSNT_EN_RSVD", "SLOT9_PRSNT_EN_RSVD",
+			"SLOT10_PRSNT_EN_RSVD", "SLOT11_PRSNT_EN_RSVD",
+			"SLOT6_EXPANDER_PRSNT_N", "SLOT7_EXPANDER_PRSNT_N",
+			"SLOT8_EXPANDER_PRSNT_N", "SLOT9_EXPANDER_PRSNT_N",
+			"SLOT10_EXPANDER_PRSNT_N", "SLOT11_EXPANDER_PRSNT_N",
+			"", "", "", "";
+	};
+
+};
+
+&i2c9 {
+	status = "okay";
+
+	temperature-sensor@4c {
+		compatible = "ti,tmp423";
+		reg = <0x4c>;
+	};
+
+	temperature-sensor@4d {
+		compatible = "ti,tmp423";
+		reg = <0x4d>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+};
+
+&i2c10 {
+	status = "okay";
+
+	temperature-sensor@4c {
+		compatible = "ti,tmp423";
+		reg = <0x4c>;
+	};
+
+	temperature-sensor@4d {
+		compatible = "ti,tmp423";
+		reg = <0x4d>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+};
+
+&i2c11 {
+	status = "okay";
+
+	temperature-sensor@48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	temperature-sensor@49 {
+		compatible = "ti,tmp275";
+		reg = <0x49>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c11mux0chn0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+
+			led-controller@60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					reg = <0>;
+					default-state = "keep";
+					label = "cablecard10-cxp-top";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					reg = <1>;
+					default-state = "keep";
+					label = "cablecard10-cxp-bot";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c11mux0chn1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+		};
+	};
+};
+
+&i2c12 {
+	status = "okay";
+
+	tpm@2e {
+		compatible = "nuvoton,npct75x", "tcg,tpm-tis-i2c";
+		reg = <0x2e>;
+		memory-region = <&event_log>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+};
+
+&i2c13 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	led-controller@60 {
+		compatible = "nxp,pca9552";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			reg = <0>;
+			default-state = "keep";
+			label = "nvme0";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			reg = <1>;
+			default-state = "keep";
+			label = "nvme1";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			reg = <2>;
+			default-state = "keep";
+			label = "nvme2";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			reg = <3>;
+			default-state = "keep";
+			label = "nvme3";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			reg = <4>;
+			default-state = "keep";
+			label = "nvme4";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			reg = <5>;
+			default-state = "keep";
+			label = "nvme5";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			reg = <6>;
+			default-state = "keep";
+			label = "nvme6";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			reg = <7>;
+			default-state = "keep";
+			label = "nvme7";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+};
+
+&i2c14 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	led-controller@60 {
+		compatible = "nxp,pca9552";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			reg = <0>;
+			default-state = "keep";
+			label = "nvme8";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			reg = <1>;
+			default-state = "keep";
+			label = "nvme9";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			reg = <2>;
+			default-state = "keep";
+			label = "nvme10";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			reg = <3>;
+			default-state = "keep";
+			label = "nvme11";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			reg = <4>;
+			default-state = "keep";
+			label = "nvme12";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			reg = <5>;
+			default-state = "keep";
+			label = "nvme13";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			reg = <6>;
+			default-state = "keep";
+			label = "nvme14";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			reg = <7>;
+			default-state = "keep";
+			label = "nvme15";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+};
+
+&i2c15 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	led-controller@60 {
+		compatible = "nxp,pca9552";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			reg = <0>;
+			default-state = "keep";
+			label = "nvme16";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			reg = <1>;
+			default-state = "keep";
+			label = "nvme17";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			reg = <2>;
+			default-state = "keep";
+			label = "nvme18";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			reg = <3>;
+			default-state = "keep";
+			label = "nvme19";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			reg = <4>;
+			default-state = "keep";
+			label = "nvme20";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			reg = <5>;
+			default-state = "keep";
+			label = "nvme21";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			reg = <6>;
+			default-state = "keep";
+			label = "nvme22";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			reg = <7>;
+			default-state = "keep";
+			label = "nvme23";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&vuart1 {
+	status = "okay";
+};
+
+&vuart2 {
+	status = "okay";
+};
+
+&lpc_ctrl {
+	status = "okay";
+	memory-region = <&flash_memory>;
+};
+
+&mac2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii3_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>,
+		 <&syscon ASPEED_CLK_MAC3RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
+&mac3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC4CLK>,
+		 <&syscon ASPEED_CLK_MAC4RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
+&wdt1 {
+	aspeed,reset-type = "none";
+	aspeed,external-signal;
+	aspeed,ext-push-pull;
+	aspeed,ext-active-high;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst1_default>;
+};
+
+&wdt2 {
+	status = "okay";
+};
+
+&kcs2 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca8 0xcac>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+	aspeed,lpc-interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-bonnell.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-bonnell.dts
new file mode 100644
index 000000000000..2f5d4075a64a
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-bonnell.dts
@@ -0,0 +1,612 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2022 IBM Corp.
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/leds/leds-pca955x.h>
+
+/ {
+	model = "Bonnell";
+	compatible = "ibm,bonnell-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial4 = &uart5;
+		i2c16 = &i2c11mux0chn0;
+		i2c17 = &i2c11mux0chn1;
+		i2c18 = &i2c11mux0chn2;
+		i2c19 = &i2c11mux0chn3;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200n8 earlycon";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		event_log: tcg_event_log@b3d00000 {
+			no-map;
+			reg = <0xb3d00000 0x100000>;
+		};
+
+		ramoops@b3e00000 {
+			compatible = "ramoops";
+			reg = <0xb3e00000 0x200000>; /* 16 * (4 * 0x8000) */
+			record-size = <0x8000>;
+			console-size = <0x8000>;
+			ftrace-size = <0x8000>;
+			pmsg-size = <0x8000>;
+			max-reason = <3>; /* KMSG_DUMP_EMERG */
+		};
+
+		/* LPC FW cycle bridge region requires natural alignment */
+		flash_memory: region@b4000000 {
+			no-map;
+			reg = <0xb4000000 0x04000000>; /* 64M */
+		};
+
+		/* VGA region is dictated by hardware strapping */
+		vga_memory: region@bf000000 {
+			no-map;
+			compatible = "shared-dma-pool";
+			reg = <0xbf000000 0x01000000>;  /* 16M */
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		fan0 {
+			gpios = <&gpio0 ASPEED_GPIO(G, 0) GPIO_ACTIVE_LOW>;
+		};
+
+		fan1 {
+			gpios = <&gpio0 ASPEED_GPIO(G, 1) GPIO_ACTIVE_LOW>;
+		};
+
+		rear-enc-id0 {
+			gpios = <&gpio0 ASPEED_GPIO(H, 2) GPIO_ACTIVE_LOW>;
+		};
+
+		rear-enc-fault0 {
+			gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <1000>;
+
+		fan0-presence {
+			label = "fan0-presence";
+			gpios = <&gpio0 ASPEED_GPIO(F, 4) GPIO_ACTIVE_LOW>;
+			linux,code = <6>;
+		};
+
+		fan1-presence {
+			label = "fan1-presence";
+			gpios = <&gpio0 ASPEED_GPIO(F, 5) GPIO_ACTIVE_LOW>;
+			linux,code = <7>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc1 7>;
+	};
+};
+
+&adc1 {
+	status = "okay";
+	aspeed,int-vref-microvolt = <2500000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+		&pinctrl_adc10_default &pinctrl_adc11_default
+		&pinctrl_adc12_default &pinctrl_adc13_default
+		&pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&uhci {
+	status = "okay";
+};
+
+&gpio0 {
+	gpio-line-names =
+		/*A0-A7*/	"","","","","","","","",
+		/*B0-B7*/	"","","","","","","checkstop","",
+		/*C0-C7*/	"","","","","","","","",
+		/*D0-D7*/	"","","","","","","","",
+		/*E0-E7*/	"","","","","","","","",
+		/*F0-F7*/	"","","rtc-battery-voltage-read-enable","reset-cause-pinhole","","","","",
+		/*G0-G7*/	"fan0","fan1","","","","","","",
+		/*H0-H7*/	"","","rear-enc-id0","rear-enc-fault0","","","","",
+		/*I0-I7*/	"","","","","","","bmc-secure-boot","",
+		/*J0-J7*/	"","","","","","","","",
+		/*K0-K7*/	"","","","","","","","",
+		/*L0-L7*/	"","","","","","","","",
+		/*M0-M7*/	"","","","","","","","",
+		/*N0-N7*/	"","","","","","","","",
+		/*O0-O7*/	"","","","usb-power","","","","",
+		/*P0-P7*/	"","","","","","","","",
+		/*Q0-Q7*/	"cfam-reset","","regulator-standby-faulted","","","","","",
+		/*R0-R7*/	"bmc-tpm-reset","power-chassis-control","power-chassis-good","","","","","",
+		/*S0-S7*/	"presence-ps0","presence-ps1","","","power-ffs-sync-history","","","",
+		/*T0-T7*/	"","","","","","","","",
+		/*U0-U7*/	"","","","","","","","",
+		/*V0-V7*/	"","","","","","","","",
+		/*W0-W7*/	"","","","","","","","",
+		/*X0-X7*/	"","","","","","","","",
+		/*Y0-Y7*/	"","","","","","","","",
+		/*Z0-Z7*/	"","","","","","","","";
+
+	usb-power-hog {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(O, 3) GPIO_ACTIVE_LOW>;
+		output-high;
+	};
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&pinctrl_emmc_default {
+	bias-disable;
+};
+
+&emmc {
+	status = "okay";
+	clk-phase-mmc-hs200 = <180>, <180>;
+};
+
+&ibt {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	eeprom@51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+
+	tca9554@20 {
+		compatible = "ti,tca9554";
+		reg = <0x20>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names = "",
+			"RUSSEL_FW_I2C_ENABLE_N",
+			"RUSSEL_OPPANEL_PRESENCE_N",
+			"BLYTH_OPPANEL_PRESENCE_N",
+			"CPU_TPM_CARD_PRESENT_N",
+			"",
+			"",
+			"DASD_BP_PRESENT_N";
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+
+	ucd90160@64 {
+		compatible = "ti,ucd90160";
+		reg = <0x64>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+
+	power-supply@5a {
+		compatible = "acbel,fsg032";
+		reg = <0x5a>;
+	};
+
+	power-supply@5b {
+		compatible = "acbel,fsg032";
+		reg = <0x5b>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	multi-master;
+	status = "okay";
+
+	si7021-a20@40 {
+		compatible = "silabs,si7020";
+		reg = <0x40>;
+	};
+
+	tmp275@48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+
+	max31785@52 {
+		compatible = "maxim,max31785a";
+		reg = <0x52>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan0: fan@0 {
+			compatible = "pmbus-fan";
+			reg = <0>;
+			tach-pulses = <2>;
+		};
+
+		fan1: fan@1 {
+			compatible = "pmbus-fan";
+			reg = <1>;
+			tach-pulses = <2>;
+		};
+	};
+
+	pca9551@60 {
+		compatible = "nxp,pca9551";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "front-sys-id0";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "front-check-log0";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "front-enc-fault1";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "front-sys-pwron0";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	ibm-panel@62 {
+		compatible = "ibm,op-panel";
+		reg = <(0x62 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	dps: dps310@76 {
+		compatible = "infineon,dps310";
+		reg = <0x76>;
+		#io-channel-cells = <0>;
+	};
+};
+
+&i2c8 {
+	status = "okay";
+
+	rtc@32 {
+		compatible = "epson,rx8900";
+		reg = <0x32>;
+	};
+
+	tmp275@48 {
+		compatible = "ti,tmp275";
+		reg = <0x48>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+
+	pca9551@60 {
+		compatible = "nxp,pca9551";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names = "",
+			"APSS_RESET_N",
+			"",
+			"N_MODE_CPU_N",
+			"",
+			"",
+			"P10_DCM_PRESENT",
+			"";
+	};
+};
+
+&i2c9 {
+	status = "okay";
+
+	tmp423a@4c {
+		compatible = "ti,tmp423";
+		reg = <0x4c>;
+	};
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+
+	tca9554@20 {
+		compatible = "ti,tca9554";
+		reg = <0x20>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names = "BOOT_RCVRY_TWI",
+			"BOOT_RCVRY_UART",
+			"",
+			"",
+			"",
+			"",
+			"",
+			"PE_SWITCH_RSTB_N";
+	};
+
+	tmp435@4c {
+		compatible = "ti,tmp435";
+		reg = <0x4c>;
+	};
+
+	pca9849@75 {
+		compatible = "nxp,pca9849";
+		reg = <0x75>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c11mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c11mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		i2c11mux0chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c11mux0chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&i2c12 {
+	status = "okay";
+
+	tpm@2e {
+		compatible = "nuvoton,npct75x", "tcg,tpm-tis-i2c";
+		reg = <0x2e>;
+		memory-region = <&event_log>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+};
+
+&i2c13 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+
+	pca9551@60 {
+		compatible = "nxp,pca9551";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "nvme3";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "nvme2";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "nvme1";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "nvme0";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+};
+
+&i2c14 {
+	status = "okay";
+};
+
+&i2c15 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&vuart1 {
+	status = "okay";
+};
+
+&vuart2 {
+	status = "okay";
+};
+
+&lpc_ctrl {
+	status = "okay";
+	memory-region = <&flash_memory>;
+};
+
+&mac2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii3_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>,
+		 <&syscon ASPEED_CLK_MAC3RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
+&wdt1 {
+	aspeed,reset-type = "none";
+	aspeed,external-signal;
+	aspeed,ext-push-pull;
+	aspeed,ext-active-high;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst1_default>;
+};
+
+&wdt2 {
+	status = "okay";
+};
+
+&kcs2 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca8 0xcac>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+	aspeed,lpc-interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+};
+
+#include "ibm-power10-dual.dtsi"
+
+&cfam0_i2c10 {
+	eeprom@50 {
+		compatible = "atmel,at30tse004a";
+		reg = <0x50>;
+	};
+};
+
+&cfam0_i2c11 {
+	eeprom@50 {
+		compatible = "atmel,at30tse004a";
+		reg = <0x50>;
+	};
+};
+
+&cfam0_i2c12 {
+	eeprom@50 {
+		compatible = "atmel,at30tse004a";
+		reg = <0x50>;
+	};
+};
+
+&cfam0_i2c13 {
+	eeprom@50 {
+		compatible = "atmel,at30tse004a";
+		reg = <0x50>;
+	};
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-everest.dts
index 578f9e2fc7ed..9f144f527f03 100644
--- a/arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-everest.dts
@@ -12,38 +12,6 @@
 	compatible = "ibm,everest-bmc", "aspeed,ast2600";
 
 	aliases {
-		i2c100 = &cfam0_i2c0;
-		i2c101 = &cfam0_i2c1;
-		i2c110 = &cfam0_i2c10;
-		i2c111 = &cfam0_i2c11;
-		i2c112 = &cfam0_i2c12;
-		i2c113 = &cfam0_i2c13;
-		i2c114 = &cfam0_i2c14;
-		i2c115 = &cfam0_i2c15;
-		i2c202 = &cfam1_i2c2;
-		i2c203 = &cfam1_i2c3;
-		i2c210 = &cfam1_i2c10;
-		i2c211 = &cfam1_i2c11;
-		i2c214 = &cfam1_i2c14;
-		i2c215 = &cfam1_i2c15;
-		i2c216 = &cfam1_i2c16;
-		i2c217 = &cfam1_i2c17;
-		i2c300 = &cfam2_i2c0;
-		i2c301 = &cfam2_i2c1;
-		i2c310 = &cfam2_i2c10;
-		i2c311 = &cfam2_i2c11;
-		i2c312 = &cfam2_i2c12;
-		i2c313 = &cfam2_i2c13;
-		i2c314 = &cfam2_i2c14;
-		i2c315 = &cfam2_i2c15;
-		i2c402 = &cfam3_i2c2;
-		i2c403 = &cfam3_i2c3;
-		i2c410 = &cfam3_i2c10;
-		i2c411 = &cfam3_i2c11;
-		i2c414 = &cfam3_i2c14;
-		i2c415 = &cfam3_i2c15;
-		i2c416 = &cfam3_i2c16;
-		i2c417 = &cfam3_i2c17;
 		i2c500 = &cfam4_i2c0;
 		i2c501 = &cfam4_i2c1;
 		i2c510 = &cfam4_i2c10;
@@ -113,22 +81,72 @@
 
 		serial4 = &uart5;
 
-		spi10 = &cfam0_spi0;
-		spi11 = &cfam0_spi1;
-		spi12 = &cfam0_spi2;
-		spi13 = &cfam0_spi3;
-		spi20 = &cfam1_spi0;
-		spi21 = &cfam1_spi1;
-		spi22 = &cfam1_spi2;
-		spi23 = &cfam1_spi3;
-		spi30 = &cfam2_spi0;
-		spi31 = &cfam2_spi1;
-		spi32 = &cfam2_spi2;
-		spi33 = &cfam2_spi3;
-		spi40 = &cfam3_spi0;
-		spi41 = &cfam3_spi1;
-		spi42 = &cfam3_spi2;
-		spi43 = &cfam3_spi3;
+		sbefifo500 = &sbefifo500;
+		sbefifo501 = &sbefifo501;
+		sbefifo510 = &sbefifo510;
+		sbefifo511 = &sbefifo511;
+		sbefifo512 = &sbefifo512;
+		sbefifo513 = &sbefifo513;
+		sbefifo514 = &sbefifo514;
+		sbefifo515 = &sbefifo515;
+		sbefifo602 = &sbefifo602;
+		sbefifo603 = &sbefifo603;
+		sbefifo610 = &sbefifo610;
+		sbefifo611 = &sbefifo611;
+		sbefifo614 = &sbefifo614;
+		sbefifo615 = &sbefifo615;
+		sbefifo616 = &sbefifo616;
+		sbefifo617 = &sbefifo617;
+		sbefifo700 = &sbefifo700;
+		sbefifo701 = &sbefifo701;
+		sbefifo710 = &sbefifo710;
+		sbefifo711 = &sbefifo711;
+		sbefifo712 = &sbefifo712;
+		sbefifo713 = &sbefifo713;
+		sbefifo714 = &sbefifo714;
+		sbefifo715 = &sbefifo715;
+		sbefifo802 = &sbefifo802;
+		sbefifo803 = &sbefifo803;
+		sbefifo810 = &sbefifo810;
+		sbefifo811 = &sbefifo811;
+		sbefifo814 = &sbefifo814;
+		sbefifo815 = &sbefifo815;
+		sbefifo816 = &sbefifo816;
+		sbefifo817 = &sbefifo817;
+
+		scom500 = &scom500;
+		scom501 = &scom501;
+		scom510 = &scom510;
+		scom511 = &scom511;
+		scom512 = &scom512;
+		scom513 = &scom513;
+		scom514 = &scom514;
+		scom515 = &scom515;
+		scom602 = &scom602;
+		scom603 = &scom603;
+		scom610 = &scom610;
+		scom611 = &scom611;
+		scom614 = &scom614;
+		scom615 = &scom615;
+		scom616 = &scom616;
+		scom617 = &scom617;
+		scom700 = &scom700;
+		scom701 = &scom701;
+		scom710 = &scom710;
+		scom711 = &scom711;
+		scom712 = &scom712;
+		scom713 = &scom713;
+		scom714 = &scom714;
+		scom715 = &scom715;
+		scom802 = &scom802;
+		scom803 = &scom803;
+		scom810 = &scom810;
+		scom811 = &scom811;
+		scom814 = &scom814;
+		scom815 = &scom815;
+		scom816 = &scom816;
+		scom817 = &scom817;
+
 		spi50 = &cfam4_spi0;
 		spi51 = &cfam4_spi1;
 		spi52 = &cfam4_spi2;
@@ -162,16 +180,14 @@
 		#size-cells = <1>;
 		ranges;
 
-		/* LPC FW cycle bridge region requires natural alignment */
-		flash_memory: region@b8000000 {
+		event_log: tcg_event_log@b3d00000 {
 			no-map;
-			reg = <0xb8000000 0x04000000>; /* 64M */
+			reg = <0xb3d00000 0x100000>;
 		};
 
-		/* 48MB region from the end of flash to start of vga memory */
-		ramoops@bc000000 {
+		ramoops@b3e00000 {
 			compatible = "ramoops";
-			reg = <0xbc000000 0x200000>; /* 16 * (4 * 0x8000) */
+			reg = <0xb3e00000 0x200000>; /* 16 * (4 * 0x8000) */
 			record-size = <0x8000>;
 			console-size = <0x8000>;
 			ftrace-size = <0x8000>;
@@ -179,6 +195,12 @@
 			max-reason = <3>; /* KMSG_DUMP_EMERG */
 		};
 
+		/* LPC FW cycle bridge region requires natural alignment */
+		flash_memory: region@b4000000 {
+			no-map;
+			reg = <0xb4000000 0x04000000>; /* 64M */
+		};
+
 		/* VGA region is dictated by hardware strapping */
 		vga_memory: region@bf000000 {
 			no-map;
@@ -189,29 +211,27 @@
 
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		poll-interval = <1000>;
 
-		fan0-presence {
+		event-fan0-presence {
 			label = "fan0-presence";
 			gpios = <&pca0 15 GPIO_ACTIVE_LOW>;
 			linux,code = <15>;
 		};
 
-		fan1-presence {
+		event-fan1-presence {
 			label = "fan1-presence";
 			gpios = <&pca0 14 GPIO_ACTIVE_LOW>;
 			linux,code = <14>;
 		};
 
-		fan2-presence {
+		event-fan2-presence {
 			label = "fan2-presence";
 			gpios = <&pca0 13 GPIO_ACTIVE_LOW>;
 			linux,code = <13>;
 		};
 
-		fan3-presence {
+		event-fan3-presence {
 			label = "fan3-presence";
 			gpios = <&pca0 12 GPIO_ACTIVE_LOW>;
 			linux,code = <12>;
@@ -247,7 +267,7 @@
 		};
 	};
 
-	iio-hwmon-battery {
+	iio-hwmon {
 		compatible = "iio-hwmon";
 		io-channels = <&adc1 7>;
 	};
@@ -283,7 +303,7 @@
 	/*P0-P7*/	"","","","","led-pcieslot-power","","","",
 	/*Q0-Q7*/	"","","regulator-standby-faulted","","","","","",
 	/*R0-R7*/	"bmc-tpm-reset","power-chassis-control","power-chassis-good","","","I2C_FLASH_MICRO_N","","",
-	/*S0-S7*/	"","","","","","","","",
+	/*S0-S7*/	"","","","","power-ffs-sync-history","","","",
 	/*T0-T7*/	"","","","","","","","",
 	/*U0-U7*/	"","","","","","","","",
 	/*V0-V7*/	"","BMC_3RESTART_ATTEMPT_P","","","","","","",
@@ -292,7 +312,7 @@
 	/*Y0-Y7*/	"","","","","","","","",
 	/*Z0-Z7*/   "","","","","","","","";
 
-	usb_power {
+	usb-power-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(O, 3) GPIO_ACTIVE_LOW>;
 		output-high;
@@ -333,6 +353,33 @@
 			"presence-base-op",
 			"";
 	};
+
+	led-controller@63 {
+		compatible = "nxp,pca9552";
+		reg = <0x63>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"presence-vrm-c12",
+			"presence-vrm-c13",
+			"presence-vrm-c15",
+			"presence-vrm-c16",
+			"presence-vrm-c17",
+			"presence-vrm-c18",
+			"presence-vrm-c20",
+			"presence-vrm-c21",
+			"presence-vrm-c54",
+			"presence-vrm-c55",
+			"presence-vrm-c57",
+			"presence-vrm-c58",
+			"presence-vrm-c59",
+			"presence-vrm-c60",
+			"presence-vrm-c62",
+			"presence-vrm-c63";
+	};
 };
 
 &i2c1 {
@@ -397,7 +444,7 @@
 			"expander-cable-card5";
 	};
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		reg = <0x70>;
 		#address-cells = <1>;
@@ -542,7 +589,7 @@
 			"expander-cable-card11";
 	};
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		reg = <0x70>;
 		#address-cells = <1>;
@@ -699,7 +746,7 @@
 &i2c6 {
 	status = "okay";
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		reg = <0x70>;
 		#address-cells = <1>;
@@ -1790,7 +1837,7 @@
 		reg = <0x50>;
 	};
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		reg = <0x70>;
 		#address-cells = <1>;
@@ -1890,6 +1937,7 @@
 	tpm@2e {
 		compatible = "nuvoton,npct75x", "tcg,tpm-tis-i2c";
 		reg = <0x2e>;
+		memory-region = <&event_log>;
 	};
 };
 
@@ -1926,7 +1974,7 @@
 		reg = <(0x62 | I2C_OWN_SLAVE_ADDRESS)>;
 	};
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		reg = <0x70>;
 		#address-cells = <1>;
@@ -2185,7 +2233,7 @@
 		};
 	};
 
-	i2c-switch@71 {
+	i2c-mux@71 {
 		compatible = "nxp,pca9546";
 		reg = <0x71>;
 		#address-cells = <1>;
@@ -2238,7 +2286,7 @@
 &i2c15 {
 	status = "okay";
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		reg = <0x70>;
 		#address-cells = <1>;
@@ -2290,7 +2338,7 @@
 		};
 	};
 
-	i2c-switch@71 {
+	i2c-mux@71 {
 		compatible = "nxp,pca9546";
 		reg = <0x71>;
 		#address-cells = <1>;
@@ -2342,7 +2390,7 @@
 		};
 	};
 
-	i2c-switch@72 {
+	i2c-mux@72 {
 		compatible = "nxp,pca9546";
 		reg = <0x72>;
 		#address-cells = <1>;
@@ -2410,167 +2458,80 @@
 	clk-phase-mmc-hs200 = <210>, <228>;
 };
 
-&fsim0 {
+&ibt {
 	status = "okay";
+};
 
-	#address-cells = <2>;
-	#size-cells = <0>;
-
-	/*
-	 * CFAM Reset is supposed to be active low but pass1 hardware is wired
-	 * active high.
-	 */
-	cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_HIGH>;
-
-	cfam@0,0 {	/* DCM0_C0 */
-		reg = <0 0>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		chip-id = <0>;
-
-		scom@1000 {
-			compatible = "ibm,fsi2pib";
-			reg = <0x1000 0x400>;
-		};
-
-		i2c@1800 {
-			compatible = "ibm,fsi-i2c-master";
-			reg = <0x1800 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			cfam0_i2c0: i2c-bus@0 {
-				reg = <0>;	/* OMI01 */
-			};
-
-			cfam0_i2c1: i2c-bus@1 {
-				reg = <1>;	/* OMI23 */
-			};
-
-			cfam0_i2c10: i2c-bus@a {
-				reg = <10>;	/* OP3A */
-			};
-
-			cfam0_i2c11: i2c-bus@b {
-				reg = <11>;	/* OP3B */
-			};
-
-			cfam0_i2c12: i2c-bus@c {
-				reg = <12>;	/* OP4A */
-			};
-
-			cfam0_i2c13: i2c-bus@d {
-				reg = <13>;	/* OP4B */
-			};
-
-			cfam0_i2c14: i2c-bus@e {
-				reg = <14>;	/* OP5A */
-			};
-
-			cfam0_i2c15: i2c-bus@f {
-				reg = <15>;	/* OP5B */
-			};
-		};
-
-		fsi2spi@1c00 {
-			compatible = "ibm,fsi2spi";
-			reg = <0x1c00 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			cfam0_spi0: spi@0 {
-				reg = <0x0>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
-
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
-				};
-			};
-
-			cfam0_spi1: spi@20 {
-				reg = <0x20>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
+&uart2 {
+	status = "okay";
+};
 
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
-				};
-			};
+&vuart1 {
+	status = "okay";
+};
 
-			cfam0_spi2: spi@40 {
-				reg = <0x40>;
-				compatible = "ibm,fsi2spi-restricted";
-				#address-cells = <1>;
-				#size-cells = <0>;
+&vuart2 {
+	status = "okay";
+};
 
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
+&lpc_ctrl {
+	status = "okay";
+	memory-region = <&flash_memory>;
+};
 
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
-				};
-			};
+&mac2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii3_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>,
+		 <&syscon ASPEED_CLK_MAC3RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
 
-			cfam0_spi3: spi@60 {
-				reg = <0x60>;
-				compatible = "ibm,fsi2spi-restricted";
-				#address-cells = <1>;
-				#size-cells = <0>;
+&mac3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC4CLK>,
+		 <&syscon ASPEED_CLK_MAC4RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
 
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
+&wdt1 {
+	aspeed,reset-type = "none";
+	aspeed,external-signal;
+	aspeed,ext-push-pull;
+	aspeed,ext-active-high;
 
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
-				};
-			};
-		};
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst1_default>;
+};
 
-		sbefifo@2400 {
-			compatible = "ibm,p9-sbefifo";
-			reg = <0x2400 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
+&wdt2 {
+	status = "okay";
+};
 
-			fsi_occ0: occ {
-				compatible = "ibm,p10-occ";
-			};
-		};
+&kcs2 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca8 0xcac>;
+};
 
-		fsi_hub0: hub@3400 {
-			compatible = "fsi-master-hub";
-			reg = <0x3400 0x400>;
-			#address-cells = <2>;
-			#size-cells = <0>;
-		};
-	};
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+	aspeed,lpc-interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
 };
 
+#include "ibm-power10-quad.dtsi"
+
 &fsi_hub0 {
-	cfam@1,0 { /* DCM0_C1 */
-		reg = <1 0>;
+	cfam@4,0 { /* DCM2_C0 */
+		reg = <4 0>;
 		#address-cells = <1>;
 		#size-cells = <1>;
-		chip-id = <1>;
+		chip-id = <4>;
 
 		scom@1000 {
 			compatible = "ibm,fsi2pib";
@@ -2583,180 +2544,260 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			cfam1_i2c2: i2c-bus@2 {
-				reg = <2>;	/* OMI45 */
-			};
-
-			cfam1_i2c3: i2c-bus@3 {
-				reg = <3>;	/* OMI67 */
-			};
+			cfam4_i2c0: i2c-bus@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;	/* OM01 */
 
-			cfam1_i2c10: i2c-bus@a {
-				reg = <10>;	/* OP3A */
-			};
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
 
-			cfam1_i2c11: i2c-bus@b {
-				reg = <11>;	/* OP3B */
-			};
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
 
-			cfam1_i2c14: i2c-bus@e {
-				reg = <14>;	/* OP5A */
-			};
+						scom500: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
 
-			cfam1_i2c15: i2c-bus@f {
-				reg = <15>;	/* OP5B */
-			};
-
-			cfam1_i2c16: i2c-bus@10 {
-				reg = <16>;	/* OP6A */
-			};
-
-			cfam1_i2c17: i2c-bus@11 {
-				reg = <17>;	/* OP6B */
+						sbefifo500: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
 			};
-		};
 
-		fsi2spi@1c00 {
-			compatible = "ibm,fsi2spi";
-			reg = <0x1c00 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			cfam1_spi0: spi@0 {
-				reg = <0x0>;
+			cfam4_i2c1: i2c-bus@1 {
 				#address-cells = <1>;
 				#size-cells = <0>;
+				reg = <1>;	/* OM23 */
 
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
 
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom501: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo501: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
 				};
 			};
 
-			cfam1_spi1: spi@20 {
-				reg = <0x20>;
+			cfam4_i2c10: i2c-bus@a {
 				#address-cells = <1>;
 				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
 
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
 
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom510: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo510: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
 				};
 			};
 
-			cfam1_spi2: spi@40 {
-				reg = <0x40>;
-				compatible = "ibm,fsi2spi-restricted";
+			cfam4_i2c11: i2c-bus@b {
 				#address-cells = <1>;
 				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
 
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
 
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom511: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo511: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
 				};
 			};
 
-			cfam1_spi3: spi@60 {
-				reg = <0x60>;
-				compatible = "ibm,fsi2spi-restricted";
+			cfam4_i2c12: i2c-bus@c {
 				#address-cells = <1>;
 				#size-cells = <0>;
+				reg = <12>;	/* OP4A */
 
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
 
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom512: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo512: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
 				};
 			};
-		};
 
-		sbefifo@2400 {
-			compatible = "ibm,p9-sbefifo";
-			reg = <0x2400 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
+			cfam4_i2c13: i2c-bus@d {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <13>;	/* OP4B */
 
-			fsi_occ1: occ {
-				compatible = "ibm,p10-occ";
-			};
-		};
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
 
-		fsi_hub1: hub@3400 {
-			compatible = "fsi-master-hub";
-			reg = <0x3400 0x400>;
-			#address-cells = <2>;
-			#size-cells = <0>;
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
 
-			no-scan-on-init;
-		};
-	};
+						scom513: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
 
-	cfam@2,0 { /* DCM1_C0 */
-		reg = <2 0>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		chip-id = <2>;
+						sbefifo513: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
 
-		scom@1000 {
-			compatible = "ibm,fsi2pib";
-			reg = <0x1000 0x400>;
-		};
+			cfam4_i2c14: i2c-bus@e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
 
-		i2c@1800 {
-			compatible = "ibm,fsi-i2c-master";
-			reg = <0x1800 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
 
-			cfam2_i2c0: i2c-bus@0 {
-				reg = <0>;	/* OM01 */
-			};
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
 
-			cfam2_i2c1: i2c-bus@1 {
-				reg = <1>;	/* OM23 */
-			};
+						scom514: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
 
-			cfam2_i2c10: i2c-bus@a {
-				reg = <10>;	/* OP3A */
+						sbefifo514: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
 			};
 
-			cfam2_i2c11: i2c-bus@b {
-				reg = <11>;	/* OP3B */
-			};
+			cfam4_i2c15: i2c-bus@f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
 
-			cfam2_i2c12: i2c-bus@c {
-				reg = <12>;	/* OP4A */
-			};
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
 
-			cfam2_i2c13: i2c-bus@d {
-				reg = <13>;	/* OP4B */
-			};
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
 
-			cfam2_i2c14: i2c-bus@e {
-				reg = <14>;	/* OP5A */
-			};
+						scom515: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
 
-			cfam2_i2c15: i2c-bus@f {
-				reg = <15>;	/* OP5B */
+						sbefifo515: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
 			};
 		};
 
@@ -2766,7 +2807,8 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			cfam2_spi0: spi@0 {
+			cfam4_spi0: spi@0 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x0>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -2782,7 +2824,8 @@
 				};
 			};
 
-			cfam2_spi1: spi@20 {
+			cfam4_spi1: spi@20 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x20>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -2798,9 +2841,9 @@
 				};
 			};
 
-			cfam2_spi2: spi@40 {
+			cfam4_spi2: spi@40 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x40>;
-				compatible = "ibm,fsi2spi-restricted";
 				#address-cells = <1>;
 				#size-cells = <0>;
 
@@ -2815,9 +2858,9 @@
 				};
 			};
 
-			cfam2_spi3: spi@60 {
+			cfam4_spi3: spi@60 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x60>;
-				compatible = "ibm,fsi2spi-restricted";
 				#address-cells = <1>;
 				#size-cells = <0>;
 
@@ -2839,12 +2882,17 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			fsi_occ2: occ {
+			fsi_occ4: occ {
 				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
 			};
 		};
 
-		fsi_hub2: hub@3400 {
+		fsi_hub4: hub@3400 {
 			compatible = "fsi-master-hub";
 			reg = <0x3400 0x400>;
 			#address-cells = <2>;
@@ -2854,11 +2902,11 @@
 		};
 	};
 
-	cfam@3,0 { /* DCM1_C1 */
-		reg = <3 0>;
+	cfam@5,0 { /* DCM2_C1 */
+		reg = <5 0>;
 		#address-cells = <1>;
 		#size-cells = <1>;
-		chip-id = <3>;
+		chip-id = <5>;
 
 		scom@1000 {
 			compatible = "ibm,fsi2pib";
@@ -2871,324 +2919,260 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			cfam3_i2c2: i2c-bus@2 {
+			cfam5_i2c2: i2c-bus@2 {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <2>;	/* OM45 */
-			};
-
-			cfam3_i2c3: i2c-bus@3 {
-				reg = <3>;	/* OM67 */
-			};
-
-			cfam3_i2c10: i2c-bus@a {
-				reg = <10>;	/* OP3A */
-			};
-
-			cfam3_i2c11: i2c-bus@b {
-				reg = <11>;	/* OP3B */
-			};
-
-			cfam3_i2c14: i2c-bus@e {
-				reg = <14>;	/* OP5A */
-			};
 
-			cfam3_i2c15: i2c-bus@f {
-				reg = <15>;	/* OP5B */
-			};
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
 
-			cfam3_i2c16: i2c-bus@10 {
-				reg = <16>;	/* OP6A */
-			};
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
 
-			cfam3_i2c17: i2c-bus@11 {
-				reg = <17>;	/* OP6B */
-			};
-		};
-
-		fsi2spi@1c00 {
-			compatible = "ibm,fsi2spi";
-			reg = <0x1c00 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
+						scom602: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
 
-			cfam3_spi0: spi@0 {
-				reg = <0x0>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
-
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
+						sbefifo602: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
 				};
 			};
 
-			cfam3_spi1: spi@20 {
-				reg = <0x20>;
+			cfam5_i2c3: i2c-bus@3 {
 				#address-cells = <1>;
 				#size-cells = <0>;
+				reg = <3>;	/* OM67 */
 
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
-
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
-				};
-			};
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
 
-			cfam3_spi2: spi@40 {
-				reg = <0x40>;
-				compatible = "ibm,fsi2spi-restricted";
-				#address-cells = <1>;
-				#size-cells = <0>;
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
 
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
+						scom603: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
 
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
+						sbefifo603: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
 				};
 			};
 
-			cfam3_spi3: spi@60 {
-				reg = <0x60>;
-				compatible = "ibm,fsi2spi-restricted";
+			cfam5_i2c10: i2c-bus@a {
 				#address-cells = <1>;
 				#size-cells = <0>;
-
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
-
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
-				};
-			};
-		};
-
-		sbefifo@2400 {
-			compatible = "ibm,p9-sbefifo";
-			reg = <0x2400 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			fsi_occ3: occ {
-				compatible = "ibm,p10-occ";
-			};
-		};
-
-		fsi_hub3: hub@3400 {
-			compatible = "fsi-master-hub";
-			reg = <0x3400 0x400>;
-			#address-cells = <2>;
-			#size-cells = <0>;
-
-			no-scan-on-init;
-		};
-	};
-
-	cfam@4,0 { /* DCM2_C0 */
-		reg = <4 0>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		chip-id = <4>;
-
-		scom@1000 {
-			compatible = "ibm,fsi2pib";
-			reg = <0x1000 0x400>;
-		};
-
-		i2c@1800 {
-			compatible = "ibm,fsi-i2c-master";
-			reg = <0x1800 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			cfam4_i2c0: i2c-bus@0 {
-				reg = <0>;	/* OM01 */
-			};
-
-			cfam4_i2c1: i2c-bus@1 {
-				reg = <1>;	/* OM23 */
-			};
-
-			cfam4_i2c10: i2c-bus@a {
 				reg = <10>;	/* OP3A */
-			};
 
-			cfam4_i2c11: i2c-bus@b {
-				reg = <11>;	/* OP3B */
-			};
-
-			cfam4_i2c12: i2c-bus@c {
-				reg = <12>;	/* OP4A */
-			};
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
 
-			cfam4_i2c13: i2c-bus@d {
-				reg = <13>;	/* OP4B */
-			};
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
 
-			cfam4_i2c14: i2c-bus@e {
-				reg = <14>;	/* OP5A */
-			};
+						scom610: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
 
-			cfam4_i2c15: i2c-bus@f {
-				reg = <15>;	/* OP5B */
+						sbefifo610: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
 			};
-		};
-
-		fsi2spi@1c00 {
-			compatible = "ibm,fsi2spi";
-			reg = <0x1c00 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
 
-			cfam4_spi0: spi@0 {
-				reg = <0x0>;
+			cfam5_i2c11: i2c-bus@b {
 				#address-cells = <1>;
 				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
 
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
-
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
-				};
-			};
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
 
-			cfam4_spi1: spi@20 {
-				reg = <0x20>;
-				#address-cells = <1>;
-				#size-cells = <0>;
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
 
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
+						scom611: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
 
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
+						sbefifo611: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
 				};
 			};
 
-			cfam4_spi2: spi@40 {
-				reg = <0x40>;
-				compatible = "ibm,fsi2spi-restricted";
+			cfam5_i2c14: i2c-bus@e {
 				#address-cells = <1>;
 				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
 
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
 
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom614: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo614: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
 				};
 			};
 
-			cfam4_spi3: spi@60 {
-				reg = <0x60>;
-				compatible = "ibm,fsi2spi-restricted";
+			cfam5_i2c15: i2c-bus@f {
 				#address-cells = <1>;
 				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
 
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
 
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
-				};
-			};
-		};
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
 
-		sbefifo@2400 {
-			compatible = "ibm,p9-sbefifo";
-			reg = <0x2400 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
+						scom615: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
 
-			fsi_occ4: occ {
-				compatible = "ibm,p10-occ";
+						sbefifo615: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
 			};
-		};
-
-		fsi_hub4: hub@3400 {
-			compatible = "fsi-master-hub";
-			reg = <0x3400 0x400>;
-			#address-cells = <2>;
-			#size-cells = <0>;
 
-			no-scan-on-init;
-		};
-	};
+			cfam5_i2c16: i2c-bus@10 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <16>;	/* OP6A */
 
-	cfam@5,0 { /* DCM2_C1 */
-		reg = <5 0>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		chip-id = <5>;
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
 
-		scom@1000 {
-			compatible = "ibm,fsi2pib";
-			reg = <0x1000 0x400>;
-		};
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
 
-		i2c@1800 {
-			compatible = "ibm,fsi-i2c-master";
-			reg = <0x1800 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
+						scom616: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
 
-			cfam5_i2c2: i2c-bus@2 {
-				reg = <2>;	/* OM45 */
-			};
-
-			cfam5_i2c3: i2c-bus@3 {
-				reg = <3>;	/* OM67 */
-			};
-
-			cfam5_i2c10: i2c-bus@a {
-				reg = <10>;	/* OP3A */
+						sbefifo616: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
 			};
 
-			cfam5_i2c11: i2c-bus@b {
-				reg = <11>;	/* OP3B */
-			};
+			cfam5_i2c17: i2c-bus@11 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <17>;	/* OP6B */
 
-			cfam5_i2c14: i2c-bus@e {
-				reg = <14>;	/* OP5A */
-			};
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
 
-			cfam5_i2c15: i2c-bus@f {
-				reg = <15>;	/* OP5B */
-			};
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
 
-			cfam5_i2c16: i2c-bus@10 {
-				reg = <16>;	/* OP6A */
-			};
+						scom617: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
 
-			cfam5_i2c17: i2c-bus@11 {
-				reg = <17>;	/* OP6B */
+						sbefifo617: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
 			};
 		};
 
@@ -3199,6 +3183,7 @@
 			#size-cells = <0>;
 
 			cfam5_spi0: spi@0 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x0>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -3215,6 +3200,7 @@
 			};
 
 			cfam5_spi1: spi@20 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x20>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -3231,8 +3217,8 @@
 			};
 
 			cfam5_spi2: spi@40 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x40>;
-				compatible = "ibm,fsi2spi-restricted";
 				#address-cells = <1>;
 				#size-cells = <0>;
 
@@ -3248,8 +3234,8 @@
 			};
 
 			cfam5_spi3: spi@60 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x60>;
-				compatible = "ibm,fsi2spi-restricted";
 				#address-cells = <1>;
 				#size-cells = <0>;
 
@@ -3273,6 +3259,11 @@
 
 			fsi_occ5: occ {
 				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
 			};
 		};
 
@@ -3304,35 +3295,259 @@
 			#size-cells = <0>;
 
 			cfam6_i2c0: i2c-bus@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <0>;	/* OM01 */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom700: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo700: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
 			};
 
 			cfam6_i2c1: i2c-bus@1 {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <1>;	/* OM23 */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom701: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo701: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
 			};
 
 			cfam6_i2c10: i2c-bus@a {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <10>;	/* OP3A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom710: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo710: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
 			};
 
 			cfam6_i2c11: i2c-bus@b {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <11>;	/* OP3B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom711: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo711: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
 			};
 
 			cfam6_i2c12: i2c-bus@c {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <12>;	/* OP4A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom712: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo712: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
 			};
 
 			cfam6_i2c13: i2c-bus@d {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <13>;	/* OP4B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom713: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo713: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
 			};
 
 			cfam6_i2c14: i2c-bus@e {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <14>;	/* OP5A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom714: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo714: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
 			};
 
 			cfam6_i2c15: i2c-bus@f {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <15>;	/* OP5B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom715: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo715: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
 			};
 		};
 
@@ -3343,6 +3558,7 @@
 			#size-cells = <0>;
 
 			cfam6_spi0: spi@0 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x0>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -3359,6 +3575,7 @@
 			};
 
 			cfam6_spi1: spi@20 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x20>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -3375,8 +3592,8 @@
 			};
 
 			cfam6_spi2: spi@40 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x40>;
-				compatible = "ibm,fsi2spi-restricted";
 				#address-cells = <1>;
 				#size-cells = <0>;
 
@@ -3392,8 +3609,8 @@
 			};
 
 			cfam6_spi3: spi@60 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x60>;
-				compatible = "ibm,fsi2spi-restricted";
 				#address-cells = <1>;
 				#size-cells = <0>;
 
@@ -3417,6 +3634,11 @@
 
 			fsi_occ6: occ {
 				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
 			};
 		};
 
@@ -3448,35 +3670,259 @@
 			#size-cells = <0>;
 
 			cfam7_i2c2: i2c-bus@2 {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <2>;	/* OM45 */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom802: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo802: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
 			};
 
 			cfam7_i2c3: i2c-bus@3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <3>;	/* OM67 */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom803: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo803: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
 			};
 
 			cfam7_i2c10: i2c-bus@a {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <10>;	/* OP3A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom810: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo810: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
 			};
 
 			cfam7_i2c11: i2c-bus@b {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <11>;	/* OP3B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom811: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo811: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
 			};
 
 			cfam7_i2c14: i2c-bus@e {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <14>;	/* OP5A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom814: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo814: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
 			};
 
 			cfam7_i2c15: i2c-bus@f {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <15>;	/* OP5B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom815: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo815: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
 			};
 
 			cfam7_i2c16: i2c-bus@10 {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <16>;	/* OP6A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom816: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo816: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
 			};
 
 			cfam7_i2c17: i2c-bus@11 {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				reg = <17>;	/* OP6B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom817: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo817: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
 			};
 		};
 
@@ -3487,6 +3933,7 @@
 			#size-cells = <0>;
 
 			cfam7_spi0: spi@0 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x0>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -3503,6 +3950,7 @@
 			};
 
 			cfam7_spi1: spi@20 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x20>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -3519,8 +3967,8 @@
 			};
 
 			cfam7_spi2: spi@40 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x40>;
-				compatible = "ibm,fsi2spi-restricted";
 				#address-cells = <1>;
 				#size-cells = <0>;
 
@@ -3536,8 +3984,8 @@
 			};
 
 			cfam7_spi3: spi@60 {
+				compatible = "ibm,spi-fsi";
 				reg = <0x60>;
-				compatible = "ibm,fsi2spi-restricted";
 				#address-cells = <1>;
 				#size-cells = <0>;
 
@@ -3561,6 +4009,11 @@
 
 			fsi_occ7: occ {
 				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
 			};
 		};
 
@@ -3576,22 +4029,6 @@
 };
 
 /* Legacy OCC numbering (to get rid of when userspace is fixed) */
-&fsi_occ0 {
-	reg = <1>;
-};
-
-&fsi_occ1 {
-	reg = <2>;
-};
-
-&fsi_occ2 {
-	reg = <3>;
-};
-
-&fsi_occ3 {
-	reg = <4>;
-};
-
 &fsi_occ4 {
 	reg = <5>;
 };
@@ -3607,70 +4044,3 @@
 &fsi_occ7 {
 	reg = <8>;
 };
-
-&ibt {
-	status = "okay";
-};
-
-&vuart1 {
-	status = "okay";
-};
-
-&vuart2 {
-	status = "okay";
-};
-
-&lpc_ctrl {
-	status = "okay";
-	memory-region = <&flash_memory>;
-};
-
-&mac2 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_rmii3_default>;
-	clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>,
-		 <&syscon ASPEED_CLK_MAC3RCLK>;
-	clock-names = "MACCLK", "RCLK";
-	use-ncsi;
-};
-
-&mac3 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_rmii4_default>;
-	clocks = <&syscon ASPEED_CLK_GATE_MAC4CLK>,
-		 <&syscon ASPEED_CLK_MAC4RCLK>;
-	clock-names = "MACCLK", "RCLK";
-	use-ncsi;
-};
-
-&wdt1 {
-	aspeed,reset-type = "none";
-	aspeed,external-signal;
-	aspeed,ext-push-pull;
-	aspeed,ext-active-high;
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_wdtrst1_default>;
-};
-
-&wdt2 {
-	status = "okay";
-};
-
-&xdma {
-	status = "okay";
-	memory-region = <&vga_memory>;
-};
-
-&kcs2 {
-	status = "okay";
-	aspeed,lpc-io-reg = <0xca8 0xcac>;
-};
-
-&kcs3 {
-	status = "okay";
-	aspeed,lpc-io-reg = <0xca2>;
-	aspeed,lpc-interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
-};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts
new file mode 100644
index 000000000000..9a43fc7bcebe
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-fuji.dts
@@ -0,0 +1,3903 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2024 IBM Corp.
+/dts-v1/;
+
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/leds/leds-pca955x.h>
+#include "aspeed-g6.dtsi"
+#include "ibm-power11-quad.dtsi"
+
+/ {
+	model = "Fuji";
+	compatible = "ibm,fuji-bmc", "aspeed,ast2600";
+
+	aliases {
+		i2c500 = &cfam4_i2c0;
+		i2c501 = &cfam4_i2c1;
+		i2c510 = &cfam4_i2c10;
+		i2c511 = &cfam4_i2c11;
+		i2c512 = &cfam4_i2c12;
+		i2c513 = &cfam4_i2c13;
+		i2c514 = &cfam4_i2c14;
+		i2c515 = &cfam4_i2c15;
+		i2c602 = &cfam5_i2c2;
+		i2c603 = &cfam5_i2c3;
+		i2c610 = &cfam5_i2c10;
+		i2c611 = &cfam5_i2c11;
+		i2c614 = &cfam5_i2c14;
+		i2c615 = &cfam5_i2c15;
+		i2c616 = &cfam5_i2c16;
+		i2c617 = &cfam5_i2c17;
+		i2c700 = &cfam6_i2c0;
+		i2c701 = &cfam6_i2c1;
+		i2c710 = &cfam6_i2c10;
+		i2c711 = &cfam6_i2c11;
+		i2c712 = &cfam6_i2c12;
+		i2c713 = &cfam6_i2c13;
+		i2c714 = &cfam6_i2c14;
+		i2c715 = &cfam6_i2c15;
+		i2c802 = &cfam7_i2c2;
+		i2c803 = &cfam7_i2c3;
+		i2c810 = &cfam7_i2c10;
+		i2c811 = &cfam7_i2c11;
+		i2c814 = &cfam7_i2c14;
+		i2c815 = &cfam7_i2c15;
+		i2c816 = &cfam7_i2c16;
+		i2c817 = &cfam7_i2c17;
+
+		i2c16 = &i2c4mux0chn0;
+		i2c17 = &i2c4mux0chn1;
+		i2c18 = &i2c4mux0chn2;
+		i2c19 = &i2c5mux0chn0;
+		i2c20 = &i2c5mux0chn1;
+		i2c21 = &i2c5mux0chn2;
+		i2c22 = &i2c5mux0chn3;
+		i2c23 = &i2c6mux0chn0;
+		i2c24 = &i2c6mux0chn1;
+		i2c25 = &i2c6mux0chn2;
+		i2c26 = &i2c6mux0chn3;
+		i2c27 = &i2c14mux0chn0;
+		i2c28 = &i2c14mux0chn1;
+		i2c29 = &i2c14mux0chn2;
+		i2c30 = &i2c14mux0chn3;
+		i2c31 = &i2c14mux1chn0;
+		i2c32 = &i2c14mux1chn1;
+		i2c33 = &i2c14mux1chn2;
+		i2c34 = &i2c14mux1chn3;
+		i2c35 = &i2c15mux0chn0;
+		i2c36 = &i2c15mux0chn1;
+		i2c37 = &i2c15mux0chn2;
+		i2c38 = &i2c15mux0chn3;
+		i2c39 = &i2c15mux1chn0;
+		i2c40 = &i2c15mux1chn1;
+		i2c41 = &i2c15mux1chn2;
+		i2c42 = &i2c15mux1chn3;
+		i2c43 = &i2c15mux2chn0;
+		i2c44 = &i2c15mux2chn1;
+		i2c45 = &i2c15mux2chn2;
+		i2c46 = &i2c15mux2chn3;
+		i2c47 = &i2c8mux0chn0;
+		i2c48 = &i2c8mux0chn1;
+
+		serial4 = &uart5;
+
+		sbefifo500 = &sbefifo500;
+		sbefifo501 = &sbefifo501;
+		sbefifo510 = &sbefifo510;
+		sbefifo511 = &sbefifo511;
+		sbefifo512 = &sbefifo512;
+		sbefifo513 = &sbefifo513;
+		sbefifo514 = &sbefifo514;
+		sbefifo515 = &sbefifo515;
+		sbefifo602 = &sbefifo602;
+		sbefifo603 = &sbefifo603;
+		sbefifo610 = &sbefifo610;
+		sbefifo611 = &sbefifo611;
+		sbefifo614 = &sbefifo614;
+		sbefifo615 = &sbefifo615;
+		sbefifo616 = &sbefifo616;
+		sbefifo617 = &sbefifo617;
+		sbefifo700 = &sbefifo700;
+		sbefifo701 = &sbefifo701;
+		sbefifo710 = &sbefifo710;
+		sbefifo711 = &sbefifo711;
+		sbefifo712 = &sbefifo712;
+		sbefifo713 = &sbefifo713;
+		sbefifo714 = &sbefifo714;
+		sbefifo715 = &sbefifo715;
+		sbefifo802 = &sbefifo802;
+		sbefifo803 = &sbefifo803;
+		sbefifo810 = &sbefifo810;
+		sbefifo811 = &sbefifo811;
+		sbefifo814 = &sbefifo814;
+		sbefifo815 = &sbefifo815;
+		sbefifo816 = &sbefifo816;
+		sbefifo817 = &sbefifo817;
+
+		scom500 = &scom500;
+		scom501 = &scom501;
+		scom510 = &scom510;
+		scom511 = &scom511;
+		scom512 = &scom512;
+		scom513 = &scom513;
+		scom514 = &scom514;
+		scom515 = &scom515;
+		scom602 = &scom602;
+		scom603 = &scom603;
+		scom610 = &scom610;
+		scom611 = &scom611;
+		scom614 = &scom614;
+		scom615 = &scom615;
+		scom616 = &scom616;
+		scom617 = &scom617;
+		scom700 = &scom700;
+		scom701 = &scom701;
+		scom710 = &scom710;
+		scom711 = &scom711;
+		scom712 = &scom712;
+		scom713 = &scom713;
+		scom714 = &scom714;
+		scom715 = &scom715;
+		scom802 = &scom802;
+		scom803 = &scom803;
+		scom810 = &scom810;
+		scom811 = &scom811;
+		scom814 = &scom814;
+		scom815 = &scom815;
+		scom816 = &scom816;
+		scom817 = &scom817;
+
+		spi50 = &cfam4_spi0;
+		spi51 = &cfam4_spi1;
+		spi52 = &cfam4_spi2;
+		spi53 = &cfam4_spi3;
+		spi60 = &cfam5_spi0;
+		spi61 = &cfam5_spi1;
+		spi62 = &cfam5_spi2;
+		spi63 = &cfam5_spi3;
+		spi70 = &cfam6_spi0;
+		spi71 = &cfam6_spi1;
+		spi72 = &cfam6_spi2;
+		spi73 = &cfam6_spi3;
+		spi80 = &cfam7_spi0;
+		spi81 = &cfam7_spi1;
+		spi82 = &cfam7_spi2;
+		spi83 = &cfam7_spi3;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		event_log: region@b3d00000 {
+			reg = <0xb3d00000 0x100000>;
+			no-map;
+		};
+
+		ramoops@b3e00000 {
+			compatible = "ramoops";
+			reg = <0xb3e00000 0x200000>; /* 16 * (4 * 0x8000) */
+			record-size = <0x8000>;
+			console-size = <0x8000>;
+			ftrace-size = <0x8000>;
+			pmsg-size = <0x8000>;
+			max-reason = <3>; /* KMSG_DUMP_EMERG */
+		};
+
+		/* LPC FW cycle bridge region requires natural alignment */
+		flash_memory: region@b4000000 {
+			reg = <0xb4000000 0x04000000>; /* 64M */
+			no-map;
+		};
+
+		/* VGA region is dictated by hardware strapping */
+		vga_memory: region@bf000000 {
+			compatible = "shared-dma-pool";
+			reg = <0xbf000000 0x01000000>; /* 16M */
+			no-map;
+		};
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		poll-interval = <1000>;
+
+		event-fan0-presence {
+			gpios = <&pca0 15 GPIO_ACTIVE_LOW>;
+			label = "fan0-presence";
+			linux,code = <15>;
+		};
+
+		event-fan1-presence {
+			gpios = <&pca0 14 GPIO_ACTIVE_LOW>;
+			label = "fan1-presence";
+			linux,code = <14>;
+		};
+
+		event-fan2-presence {
+			gpios = <&pca0 13 GPIO_ACTIVE_LOW>;
+			label = "fan2-presence";
+			linux,code = <13>;
+		};
+
+		event-fan3-presence {
+			gpios = <&pca0 12 GPIO_ACTIVE_LOW>;
+			label = "fan3-presence";
+			linux,code = <12>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		/* RTC battery fault LED at the back */
+		led-rtc-battery {
+			gpios = <&gpio0 ASPEED_GPIO(H, 0) GPIO_ACTIVE_LOW>;
+		};
+
+		/* BMC Card fault LED at the back */
+		led-bmc {
+			gpios = <&gpio0 ASPEED_GPIO(H, 1) GPIO_ACTIVE_LOW>;
+		};
+
+		/* Enclosure Identify LED at the back */
+		led-rear-enc-id0 {
+			gpios = <&gpio0 ASPEED_GPIO(H, 2) GPIO_ACTIVE_LOW>;
+		};
+
+		/* Enclosure fault LED at the back */
+		led-rear-enc-fault0 {
+			gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>;
+		};
+
+		/* PCIE slot power LED */
+		led-pcieslot-power {
+			gpios = <&gpio0 ASPEED_GPIO(P, 4) GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc1 7>;
+	};
+};
+
+&adc1 {
+	status = "okay";
+	aspeed,int-vref-microvolt = <2500000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+				 &pinctrl_adc10_default &pinctrl_adc11_default
+				 &pinctrl_adc12_default &pinctrl_adc13_default
+				 &pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&gpio0 {
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","","","",
+	/*B0-B7*/	"bmc-management-ready","","","","","","checkstop","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"","","","","","","","",
+	/*F0-F7*/	"","","rtc-battery-voltage-read-enable","reset-cause-pinhole","","",
+			"factory-reset-toggle","",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"led-rtc-battery","led-bmc","led-rear-enc-id0","led-rear-enc-fault0","","",
+			"","",
+	/*I0-I7*/	"","","","","","","bmc-secure-boot","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","usb-power","","","","",
+	/*P0-P7*/	"","","","","led-pcieslot-power","","","",
+	/*Q0-Q7*/	"","","regulator-standby-faulted","","","","","",
+	/*R0-R7*/	"bmc-tpm-reset","power-chassis-control","power-chassis-good","","",
+			"I2C_FLASH_MICRO_N","","",
+	/*S0-S7*/	"","","","","power-ffs-sync-history","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","BMC_3RESTART_ATTEMPT_P","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"","","","","","","","";
+
+	usb-power-hog {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(O, 3) GPIO_ACTIVE_LOW>;
+		output-high;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	eeprom@51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+
+	led-controller@62 {
+		compatible = "nxp,pca9552";
+		reg = <0x62>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"presence-ps0",
+			"presence-ps1",
+			"presence-ps2",
+			"presence-ps3",
+			"presence-pdb",
+			"presence-tpm",
+			"", "",
+			"presence-cp0",
+			"presence-cp1",
+			"presence-cp2",
+			"presence-cp3",
+			"presence-dasd",
+			"presence-lcd-op",
+			"presence-base-op",
+			"";
+	};
+
+	led-controller@63 {
+		compatible = "nxp,pca9552";
+		reg = <0x63>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"presence-vrm-c12",
+			"presence-vrm-c13",
+			"presence-vrm-c15",
+			"presence-vrm-c16",
+			"presence-vrm-c17",
+			"presence-vrm-c18",
+			"presence-vrm-c20",
+			"presence-vrm-c21",
+			"presence-vrm-c54",
+			"presence-vrm-c55",
+			"presence-vrm-c57",
+			"presence-vrm-c58",
+			"presence-vrm-c59",
+			"presence-vrm-c60",
+			"presence-vrm-c62",
+			"presence-vrm-c63";
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+
+	eeprom@54 {
+		compatible = "atmel,24c128";
+		reg = <0x54>;
+	};
+
+	power-supply@68 {
+		compatible = "ibm,cffps";
+		reg = <0x68>;
+	};
+
+	power-supply@69 {
+		compatible = "ibm,cffps";
+		reg = <0x69>;
+	};
+
+	power-supply@6b {
+		compatible = "ibm,cffps";
+		reg = <0x6b>;
+	};
+
+	power-supply@6d {
+		compatible = "ibm,cffps";
+		reg = <0x6d>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+
+	led-controller@65 {
+		compatible = "nxp,pca9552";
+		reg = <0x65>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"presence-cable-card1",
+			"presence-cable-card2",
+			"presence-cable-card3",
+			"presence-cable-card4",
+			"presence-cable-card5",
+			"expander-cable-card1",
+			"expander-cable-card2",
+			"expander-cable-card3",
+			"expander-cable-card4",
+			"expander-cable-card5";
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c4mux0chn0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@52 {
+				compatible = "atmel,24c64";
+				reg = <0x52>;
+			};
+
+			led-controller@62 {
+				compatible = "nxp,pca9551";
+				reg = <0x62>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					reg = <0>;
+					default-state = "keep";
+					label = "cablecard-c01-cxp-top";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					reg = <1>;
+					default-state = "keep";
+					label = "cablecard-c01-cxp-bot";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c4mux0chn1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+
+			led-controller@60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					reg = <0>;
+					default-state = "keep";
+					label = "cablecard-c02-cxp-top";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					reg = <1>;
+					default-state = "keep";
+					label = "cablecard-c02-cxp-bot";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c4mux0chn2: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+
+			led-controller@61 {
+				compatible = "nxp,pca9551";
+				reg = <0x61>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					reg = <0>;
+					default-state = "keep";
+					label = "cablecard-c03-cxp-top";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					reg = <1>;
+					default-state = "keep";
+					label = "cablecard-c03-cxp-bot";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	led-controller@66 {
+		compatible = "nxp,pca9552";
+		reg = <0x66>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"presence-cable-card6",
+			"presence-cable-card7",
+			"presence-cable-card8",
+			"presence-cable-card9",
+			"presence-cable-card10",
+			"presence-cable-card11",
+			"expander-cable-card6",
+			"expander-cable-card7",
+			"expander-cable-card8",
+			"expander-cable-card9",
+			"expander-cable-card10",
+			"expander-cable-card11";
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c5mux0chn0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+
+			led-controller@60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					reg = <0>;
+					default-state = "keep";
+					label = "cablecard-c04-cxp-top";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					reg = <1>;
+					default-state = "keep";
+					label = "cablecard-c04-cxp-bot";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c5mux0chn1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+
+			led-controller@61 {
+				compatible = "nxp,pca9551";
+				reg = <0x61>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					reg = <0>;
+					default-state = "keep";
+					label = "cablecard-c05-cxp-top";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					reg = <1>;
+					default-state = "keep";
+					label = "cablecard-c05-cxp-bot";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c5mux0chn2: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@52 {
+				compatible = "atmel,24c64";
+				reg = <0x52>;
+			};
+
+			led-controller@62 {
+				compatible = "nxp,pca9551";
+				reg = <0x62>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					reg = <0>;
+					default-state = "keep";
+					label = "cablecard-c06-cxp-top";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					reg = <1>;
+					default-state = "keep";
+					label = "cablecard-c06-cxp-bot";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c5mux0chn3: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+
+			led-controller@63 {
+				compatible = "nxp,pca9551";
+				reg = <0x63>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					reg = <0>;
+					default-state = "keep";
+					label = "cablecard-c07-cxp-top";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					reg = <1>;
+					default-state = "keep";
+					label = "cablecard-c07-cxp-bot";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+	};
+};
+
+&i2c6 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c6mux0chn0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+
+			led-controller@60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					reg = <0>;
+					default-state = "keep";
+					label = "cablecard-c08-cxp-top";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					reg = <1>;
+					default-state = "keep";
+					label = "cablecard-c08-cxp-bot";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c6mux0chn1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@52 {
+				compatible = "atmel,24c64";
+				reg = <0x52>;
+			};
+
+			led-controller@62 {
+				compatible = "nxp,pca9551";
+				reg = <0x62>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					reg = <0>;
+					default-state = "keep";
+					label = "cablecard-c09-cxp-top";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					reg = <1>;
+					default-state = "keep";
+					label = "cablecard-c09-cxp-bot";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c6mux0chn2: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+
+			led-controller@63 {
+				compatible = "nxp,pca9551";
+				reg = <0x63>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					reg = <0>;
+					default-state = "keep";
+					label = "cablecard-c10-cxp-top";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					reg = <1>;
+					default-state = "keep";
+					label = "cablecard-c10-cxp-bot";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c6mux0chn3: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+
+			led-controller@61 {
+				compatible = "nxp,pca9551";
+				reg = <0x61>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					reg = <0>;
+					default-state = "keep";
+					label = "cablecard-c11-cxp-top";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					reg = <1>;
+					default-state = "keep";
+					label = "cablecard-c11-cxp-bot";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+	};
+
+	led-controller@65 {
+		compatible = "nxp,pca9552";
+		reg = <0x65>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@1 {
+			reg = <1>;
+			default-state = "keep";
+			label = "pcieslot-c01";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			reg = <2>;
+			default-state = "keep";
+			label = "pcieslot-c02";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			reg = <3>;
+			default-state = "keep";
+			label = "pcieslot-c03";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			reg = <4>;
+			default-state = "keep";
+			label = "pcieslot-c04";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			reg = <5>;
+			default-state = "keep";
+			label = "pcieslot-c05";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			reg = <6>;
+			default-state = "keep";
+			label = "pcieslot-c06";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			reg = <7>;
+			default-state = "keep";
+			label = "pcieslot-c07";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			reg = <8>;
+			default-state = "keep";
+			label = "pcieslot-c08";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			reg = <9>;
+			default-state = "keep";
+			label = "pcieslot-c09";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@a {
+			reg = <10>;
+			default-state = "keep";
+			label = "pcieslot-c10";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@b {
+			reg = <11>;
+			default-state = "keep";
+			label = "pcieslot-c11";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+};
+
+&i2c7 {
+	status = "okay";
+
+	led-controller@31 {
+		compatible = "ibm,pca9552";
+		reg = <0x31>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			reg = <0>;
+			default-state = "keep";
+			label = "ddimm0";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			reg = <1>;
+			default-state = "keep";
+			label = "ddimm1";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			reg = <2>;
+			default-state = "keep";
+			label = "ddimm2";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			reg = <3>;
+			default-state = "keep";
+			label = "ddimm3";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			reg = <4>;
+			default-state = "keep";
+			label = "ddimm4";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			reg = <5>;
+			default-state = "keep";
+			label = "ddimm5";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			reg = <6>;
+			default-state = "keep";
+			label = "ddimm6";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			reg = <7>;
+			default-state = "keep";
+			label = "ddimm7";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			reg = <8>;
+			default-state = "keep";
+			label = "ddimm8";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			reg = <9>;
+			default-state = "keep";
+			label = "ddimm9";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@a {
+			reg = <10>;
+			default-state = "keep";
+			label = "ddimm10";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@b {
+			reg = <11>;
+			default-state = "keep";
+			label = "ddimm11";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@c {
+			reg = <12>;
+			default-state = "keep";
+			label = "ddimm12";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@d {
+			reg = <13>;
+			default-state = "keep";
+			label = "ddimm13";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@e {
+			reg = <14>;
+			default-state = "keep";
+			label = "ddimm14";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@f {
+			reg = <15>;
+			default-state = "keep";
+			label = "ddimm15";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	led-controller@32 {
+		compatible = "ibm,pca9552";
+		reg = <0x32>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			reg = <0>;
+			default-state = "keep";
+			label = "ddimm16";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			reg = <1>;
+			default-state = "keep";
+			label = "ddimm17";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			reg = <2>;
+			default-state = "keep";
+			label = "ddimm18";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			reg = <3>;
+			default-state = "keep";
+			label = "ddimm19";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			reg = <4>;
+			default-state = "keep";
+			label = "ddimm20";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			reg = <5>;
+			default-state = "keep";
+			label = "ddimm21";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			reg = <6>;
+			default-state = "keep";
+			label = "ddimm22";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			reg = <7>;
+			default-state = "keep";
+			label = "ddimm23";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			reg = <8>;
+			default-state = "keep";
+			label = "ddimm24";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			reg = <9>;
+			default-state = "keep";
+			label = "ddimm25";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@a {
+			reg = <10>;
+			default-state = "keep";
+			label = "ddimm26";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@b {
+			reg = <11>;
+			default-state = "keep";
+			label = "ddimm27";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@c {
+			reg = <12>;
+			default-state = "keep";
+			label = "ddimm28";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@d {
+			reg = <13>;
+			default-state = "keep";
+			label = "ddimm29";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@e {
+			reg = <14>;
+			default-state = "keep";
+			label = "ddimm30";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@f {
+			reg = <15>;
+			default-state = "keep";
+			label = "ddimm31";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	led-controller@33 {
+		compatible = "ibm,pca9552";
+		reg = <0x33>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			reg = <0>;
+			default-state = "keep";
+			label = "ddimm32";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			reg = <1>;
+			default-state = "keep";
+			label = "ddimm33";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			reg = <2>;
+			default-state = "keep";
+			label = "ddimm34";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			reg = <3>;
+			default-state = "keep";
+			label = "ddimm35";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			reg = <4>;
+			default-state = "keep";
+			label = "ddimm36";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			reg = <5>;
+			default-state = "keep";
+			label = "ddimm37";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			reg = <6>;
+			default-state = "keep";
+			label = "ddimm38";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			reg = <7>;
+			default-state = "keep";
+			label = "ddimm39";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			reg = <8>;
+			default-state = "keep";
+			label = "ddimm40";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			reg = <9>;
+			default-state = "keep";
+			label = "ddimm41";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@a {
+			reg = <10>;
+			default-state = "keep";
+			label = "ddimm42";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@b {
+			reg = <11>;
+			default-state = "keep";
+			label = "ddimm43";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@c {
+			reg = <12>;
+			default-state = "keep";
+			label = "ddimm44";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@d {
+			reg = <13>;
+			default-state = "keep";
+			label = "ddimm45";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@e {
+			reg = <14>;
+			default-state = "keep";
+			label = "ddimm46";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@f {
+			reg = <15>;
+			default-state = "keep";
+			label = "ddimm47";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	led-controller@30 {
+		compatible = "ibm,pca9552";
+		reg = <0x30>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			reg = <0>;
+			default-state = "keep";
+			label = "ddimm48";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			reg = <1>;
+			default-state = "keep";
+			label = "ddimm49";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			reg = <2>;
+			default-state = "keep";
+			label = "ddimm50";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			reg = <3>;
+			default-state = "keep";
+			label = "ddimm51";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			reg = <4>;
+			default-state = "keep";
+			label = "ddimm52";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			reg = <5>;
+			default-state = "keep";
+			label = "ddimm53";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			reg = <6>;
+			default-state = "keep";
+			label = "ddimm54";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			reg = <7>;
+			default-state = "keep";
+			label = "ddimm55";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			reg = <8>;
+			default-state = "keep";
+			label = "ddimm56";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			reg = <9>;
+			default-state = "keep";
+			label = "ddimm57";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@a {
+			reg = <10>;
+			default-state = "keep";
+			label = "ddimm58";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@b {
+			reg = <11>;
+			default-state = "keep";
+			label = "ddimm59";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@c {
+			reg = <12>;
+			default-state = "keep";
+			label = "ddimm60";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@d {
+			reg = <13>;
+			default-state = "keep";
+			label = "ddimm61";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@e {
+			reg = <14>;
+			default-state = "keep";
+			label = "ddimm62";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@f {
+			reg = <15>;
+			default-state = "keep";
+			label = "ddimm63";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	led-controller@34 {
+		compatible = "ibm,pca9552";
+		reg = <0x34>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			reg = <0>;
+			default-state = "keep";
+			label = "planar";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			reg = <1>;
+			default-state = "keep";
+			label = "tpm";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			reg = <2>;
+			default-state = "keep";
+			label = "cpu3-c61";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			reg = <3>;
+			default-state = "keep";
+			label = "cpu0-c14";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			reg = <4>;
+			default-state = "keep";
+			label = "opencapi-connector3";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			reg = <5>;
+			default-state = "keep";
+			label = "opencapi-connector4";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			reg = <6>;
+			default-state = "keep";
+			label = "opencapi-connector5";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			reg = <8>;
+			default-state = "keep";
+			label = "vrm4";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			reg = <9>;
+			default-state = "keep";
+			label = "vrm5";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@a {
+			reg = <10>;
+			default-state = "keep";
+			label = "vrm6";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@b {
+			reg = <11>;
+			default-state = "keep";
+			label = "vrm7";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@c {
+			reg = <12>;
+			default-state = "keep";
+			label = "vrm12";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@d {
+			reg = <13>;
+			default-state = "keep";
+			label = "vrm13";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@e {
+			reg = <14>;
+			default-state = "keep";
+			label = "vrm14";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@f {
+			reg = <15>;
+			default-state = "keep";
+			label = "vrm15";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	led-controller@35 {
+		compatible = "ibm,pca9552";
+		reg = <0x35>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			reg = <0>;
+			default-state = "keep";
+			label = "dasd-backplane";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			reg = <1>;
+			default-state = "keep";
+			label = "power-distribution";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			reg = <2>;
+			default-state = "keep";
+			label = "cpu1-c19";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			reg = <3>;
+			default-state = "keep";
+			label = "cpu2-c56";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			reg = <4>;
+			default-state = "keep";
+			label = "opencapi-connector0";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			reg = <5>;
+			default-state = "keep";
+			label = "opencapi-connector1";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			reg = <6>;
+			default-state = "keep";
+			label = "opencapi-connector2";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			reg = <8>;
+			default-state = "keep";
+			label = "vrm0";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			reg = <9>;
+			default-state = "keep";
+			label = "vrm1";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@a {
+			reg = <10>;
+			default-state = "keep";
+			label = "vrm2";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@b {
+			reg = <11>;
+			default-state = "keep";
+			label = "vrm3";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@c {
+			reg = <12>;
+			default-state = "keep";
+			label = "vrm8";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@d {
+			reg = <13>;
+			default-state = "keep";
+			label = "vrm9";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@e {
+			reg = <14>;
+			default-state = "keep";
+			label = "vrm10";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@f {
+			reg = <15>;
+			default-state = "keep";
+			label = "vrm11";
+			retain-state-shutdown;
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+};
+
+&i2c8 {
+	status = "okay";
+
+	pmic@11 {
+		compatible = "ti,ucd90320";
+		reg = <0x11>;
+	};
+
+	rtc@32 {
+		compatible = "epson,rx8900";
+		reg = <0x32>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+		reset-gpio = <&gpio0 ASPEED_GPIO(S, 5) GPIO_ACTIVE_LOW>;
+
+		i2c8mux0chn0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c8mux0chn1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&i2c9 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+	};
+
+	eeprom@53 {
+		compatible = "atmel,24c128";
+		reg = <0x53>;
+	};
+
+	eeprom@52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+	};
+};
+
+&i2c10 {
+	status = "okay";
+
+	eeprom@51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+
+	eeprom@53 {
+		compatible = "atmel,24c128";
+		reg = <0x53>;
+	};
+
+	eeprom@52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+	};
+};
+
+&i2c11 {
+	status = "okay";
+
+	eeprom@51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+
+	eeprom@53 {
+		compatible = "atmel,24c128";
+		reg = <0x53>;
+	};
+
+	eeprom@52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+	};
+};
+
+&i2c12 {
+	status = "okay";
+
+	tpm@2e {
+		compatible = "nuvoton,npct75x", "tcg,tpm-tis-i2c";
+		reg = <0x2e>;
+		memory-region = <&event_log>;
+	};
+};
+
+&i2c13 {
+	status = "okay";
+
+	eeprom@51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+	};
+
+	eeprom@53 {
+		compatible = "atmel,24c128";
+		reg = <0x53>;
+	};
+
+	eeprom@52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+	};
+};
+
+&i2c14 {
+	multi-master;
+	status = "okay";
+
+	lcd-controller@62 {
+		compatible = "ibm,op-panel";
+		reg = <(0x62 | I2C_OWN_SLAVE_ADDRESS)>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		idle-state = <1>;
+
+		i2c14mux0chn0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		i2c14mux0chn1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@51 {
+				compatible = "atmel,24c32";
+				reg = <0x51>;
+			};
+		};
+
+		i2c14mux0chn2: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
+
+			led-controller@60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					reg = <0>;
+					default-state = "keep";
+					label = "front-sys-id0";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					reg = <1>;
+					default-state = "keep";
+					label = "front-check-log0";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@2 {
+					reg = <2>;
+					default-state = "keep";
+					label = "front-enc-fault1";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@3 {
+					reg = <3>;
+					default-state = "keep";
+					label = "front-sys-pwron0";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+		};
+
+		i2c14mux0chn3: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			pwm@52 {
+				compatible = "maxim,max31785a";
+				reg = <0x52>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			led-controller@60 {
+				compatible = "nxp,pca9552";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					reg = <0>;
+					default-state = "keep";
+					label = "nvme0";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					reg = <1>;
+					default-state = "keep";
+					label = "nvme1";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@2 {
+					reg = <2>;
+					default-state = "keep";
+					label = "nvme2";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@3 {
+					reg = <3>;
+					default-state = "keep";
+					label = "nvme3";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@4 {
+					reg = <4>;
+					default-state = "keep";
+					label = "nvme4";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@5 {
+					reg = <5>;
+					default-state = "keep";
+					label = "nvme5";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@6 {
+					reg = <6>;
+					default-state = "keep";
+					label = "nvme6";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@7 {
+					reg = <7>;
+					default-state = "keep";
+					label = "nvme7";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@8 {
+					reg = <8>;
+					default-state = "keep";
+					label = "nvme8";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@9 {
+					reg = <9>;
+					default-state = "keep";
+					label = "nvme9";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@a {
+					reg = <10>;
+					default-state = "keep";
+					label = "fan0";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@b {
+					reg = <11>;
+					default-state = "keep";
+					label = "fan1";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@c {
+					reg = <12>;
+					default-state = "keep";
+					label = "fan2";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@d {
+					reg = <13>;
+					default-state = "keep";
+					label = "fan3";
+					retain-state-shutdown;
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+
+			pca0: led-controller@61 {
+				compatible = "nxp,pca9552";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x61>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				gpio-line-names =
+					"","","","",
+					"","","","",
+					"","","","",
+					"presence-fan3",
+					"presence-fan2",
+					"presence-fan1",
+					"presence-fan0";
+			};
+		};
+	};
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9546";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c14mux1chn0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
+		};
+
+		i2c14mux1chn1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
+		};
+
+		i2c14mux1chn2: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
+		};
+
+		i2c14mux1chn3: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
+		};
+	};
+};
+
+&i2c15 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c15mux0chn0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux0chn1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux0chn2: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux0chn3: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+	};
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9546";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c15mux1chn0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux1chn1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux1chn2: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux1chn3: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+	};
+
+	i2c-mux@72 {
+		compatible = "nxp,pca9546";
+		reg = <0x72>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c15mux2chn0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux2chn1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@53 {
+				compatible = "atmel,24c64";
+				reg = <0x53>;
+			};
+		};
+
+		i2c15mux2chn2: i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c15mux2chn3: i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&uhci {
+	status = "okay";
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&pinctrl_emmc_default {
+	bias-disable;
+};
+
+&emmc {
+	status = "okay";
+	clk-phase-mmc-hs200 = <210>, <228>;
+};
+
+&ibt {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&vuart1 {
+	status = "okay";
+};
+
+&vuart2 {
+	status = "okay";
+};
+
+&lpc_ctrl {
+	status = "okay";
+	memory-region = <&flash_memory>;
+};
+
+&mac2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii3_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>,
+		 <&syscon ASPEED_CLK_MAC3RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
+&mac3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC4CLK>,
+		 <&syscon ASPEED_CLK_MAC4RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
+&wdt1 {
+	aspeed,reset-type = "none";
+	aspeed,external-signal;
+	aspeed,ext-push-pull;
+	aspeed,ext-active-high;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst1_default>;
+};
+
+&wdt2 {
+	status = "okay";
+};
+
+&kcs2 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca8 0xcac>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+	aspeed,lpc-interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&fsi_hub0 {
+	cfam@4,0 { /* DCM2_C0 */
+		reg = <4 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <4>;
+
+		scom@1000 {
+			compatible = "ibm,p9-scom";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,i2c-fsi";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam4_i2c0: i2c-bus@0 {
+				reg = <0>;	/* OM01 */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom500: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo500: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c1: i2c-bus@1 {
+				reg = <1>;	/* OM23 */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom501: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo501: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c10: i2c-bus@a {
+				reg = <10>;	/* OP3A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom510: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo510: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c11: i2c-bus@b {
+				reg = <11>;	/* OP3B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom511: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo511: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c12: i2c-bus@c {
+				reg = <12>;	/* OP4A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom512: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo512: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c13: i2c-bus@d {
+				reg = <13>;	/* OP4B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom513: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo513: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c14: i2c-bus@e {
+				reg = <14>;	/* OP5A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom514: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo514: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam4_i2c15: i2c-bus@f {
+				reg = <15>;	/* OP5B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom515: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo515: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam4_spi0: spi@0 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam4_spi1: spi@20 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam4_spi2: spi@40 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam4_spi3: spi@60 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+
+			occ {
+				compatible = "ibm,p10-occ";
+
+				hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi@3400 {
+			compatible = "ibm,p9-fsi-controller";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			no-scan-on-init;
+		};
+	};
+
+	cfam@5,0 { /* DCM2_C1 */
+		reg = <5 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <5>;
+
+		scom@1000 {
+			compatible = "ibm,p9-scom";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,i2c-fsi";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam5_i2c2: i2c-bus@2 {
+				reg = <2>;	/* OM45 */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom602: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo602: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c3: i2c-bus@3 {
+				reg = <3>;	/* OM67 */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom603: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo603: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c10: i2c-bus@a {
+				reg = <10>;	/* OP3A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom610: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo610: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c11: i2c-bus@b {
+				reg = <11>;	/* OP3B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom611: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo611: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c14: i2c-bus@e {
+				reg = <14>;	/* OP5A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom614: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo614: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c15: i2c-bus@f {
+				reg = <15>;	/* OP5B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom615: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo615: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c16: i2c-bus@10 {
+				reg = <16>;	/* OP6A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom616: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo616: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam5_i2c17: i2c-bus@11 {
+				reg = <17>;	/* OP6B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom617: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo617: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam5_spi0: spi@0 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam5_spi1: spi@20 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam5_spi2: spi@40 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam5_spi3: spi@60 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+
+			occ {
+				compatible = "ibm,p10-occ";
+
+				hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi@3400 {
+			compatible = "ibm,p9-fsi-controller";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			no-scan-on-init;
+		};
+	};
+
+	cfam@6,0 { /* DCM3_C0 */
+		reg = <6 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <6>;
+
+		scom@1000 {
+			compatible = "ibm,p9-scom";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,i2c-fsi";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam6_i2c0: i2c-bus@0 {
+				reg = <0>;	/* OM01 */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom700: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo700: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c1: i2c-bus@1 {
+				reg = <1>;	/* OM23 */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom701: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo701: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c10: i2c-bus@a {
+				reg = <10>;	/* OP3A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom710: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo710: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c11: i2c-bus@b {
+				reg = <11>;	/* OP3B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom711: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo711: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c12: i2c-bus@c {
+				reg = <12>;	/* OP4A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom712: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo712: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c13: i2c-bus@d {
+				reg = <13>;	/* OP4B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom713: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo713: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c14: i2c-bus@e {
+				reg = <14>;	/* OP5A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom714: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo714: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam6_i2c15: i2c-bus@f {
+				reg = <15>;	/* OP5B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom715: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo715: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam6_spi0: spi@0 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam6_spi1: spi@20 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam6_spi2: spi@40 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam6_spi3: spi@60 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+
+			occ {
+				compatible = "ibm,p10-occ";
+
+				hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi@3400 {
+			compatible = "ibm,p9-fsi-controller";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			no-scan-on-init;
+		};
+	};
+
+	cfam@7,0 { /* DCM3_C1 */
+		reg = <7 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <7>;
+
+		scom@1000 {
+			compatible = "ibm,p9-scom";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,i2c-fsi";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam7_i2c2: i2c-bus@2 {
+				reg = <2>;	/* OM45 */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom802: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo802: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c3: i2c-bus@3 {
+				reg = <3>;	/* OM67 */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom803: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo803: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c10: i2c-bus@a {
+				reg = <10>;	/* OP3A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom810: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo810: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c11: i2c-bus@b {
+				reg = <11>;	/* OP3B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom811: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo811: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c14: i2c-bus@e {
+				reg = <14>;	/* OP5A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom814: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo814: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c15: i2c-bus@f {
+				reg = <15>;	/* OP5B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom815: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo815: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c16: i2c-bus@10 {
+				reg = <16>;	/* OP6A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom816: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo816: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam7_i2c17: i2c-bus@11 {
+				reg = <17>;	/* OP6B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom817: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo817: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam7_spi0: spi@0 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam7_spi1: spi@20 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam7_spi2: spi@40 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam7_spi3: spi@60 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+
+			occ {
+				compatible = "ibm,p10-occ";
+
+				hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi@3400 {
+			compatible = "ibm,p9-fsi-controller";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			no-scan-on-init;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier-1s4u.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-rainier-1s4u.dts
index f5f5b18c113a..f5f5b18c113a 100644
--- a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier-1s4u.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-rainier-1s4u.dts
diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier-4u.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-rainier-4u.dts
index 342546a3c0f5..342546a3c0f5 100644
--- a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier-4u.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-rainier-4u.dts
diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-rainier.dts
index 528b49e2c0f8..c5fb5d410001 100644
--- a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-rainier.dts
@@ -12,39 +12,6 @@
 	compatible = "ibm,rainier-bmc", "aspeed,ast2600";
 
 	aliases {
-		i2c100 = &cfam0_i2c0;
-		i2c101 = &cfam0_i2c1;
-		i2c110 = &cfam0_i2c10;
-		i2c111 = &cfam0_i2c11;
-		i2c112 = &cfam0_i2c12;
-		i2c113 = &cfam0_i2c13;
-		i2c114 = &cfam0_i2c14;
-		i2c115 = &cfam0_i2c15;
-		i2c202 = &cfam1_i2c2;
-		i2c203 = &cfam1_i2c3;
-		i2c210 = &cfam1_i2c10;
-		i2c211 = &cfam1_i2c11;
-		i2c214 = &cfam1_i2c14;
-		i2c215 = &cfam1_i2c15;
-		i2c216 = &cfam1_i2c16;
-		i2c217 = &cfam1_i2c17;
-		i2c300 = &cfam2_i2c0;
-		i2c301 = &cfam2_i2c1;
-		i2c310 = &cfam2_i2c10;
-		i2c311 = &cfam2_i2c11;
-		i2c312 = &cfam2_i2c12;
-		i2c313 = &cfam2_i2c13;
-		i2c314 = &cfam2_i2c14;
-		i2c315 = &cfam2_i2c15;
-		i2c402 = &cfam3_i2c2;
-		i2c403 = &cfam3_i2c3;
-		i2c410 = &cfam3_i2c10;
-		i2c411 = &cfam3_i2c11;
-		i2c414 = &cfam3_i2c14;
-		i2c415 = &cfam3_i2c15;
-		i2c416 = &cfam3_i2c16;
-		i2c417 = &cfam3_i2c17;
-
 		serial4 = &uart5;
 		i2c16 = &i2c2mux0;
 		i2c17 = &i2c2mux1;
@@ -61,23 +28,6 @@
 		i2c28 = &i2c6mux0chn3;
 		i2c29 = &i2c11mux0chn0;
 		i2c30 = &i2c11mux0chn1;
-
-		spi10 = &cfam0_spi0;
-		spi11 = &cfam0_spi1;
-		spi12 = &cfam0_spi2;
-		spi13 = &cfam0_spi3;
-		spi20 = &cfam1_spi0;
-		spi21 = &cfam1_spi1;
-		spi22 = &cfam1_spi2;
-		spi23 = &cfam1_spi3;
-		spi30 = &cfam2_spi0;
-		spi31 = &cfam2_spi1;
-		spi32 = &cfam2_spi2;
-		spi33 = &cfam2_spi3;
-		spi40 = &cfam3_spi0;
-		spi41 = &cfam3_spi1;
-		spi42 = &cfam3_spi2;
-		spi43 = &cfam3_spi3;
 	};
 
 	chosen {
@@ -95,14 +45,9 @@
 		#size-cells = <1>;
 		ranges;
 
-		flash_memory: region@b8000000 {
-			no-map;
-			reg = <0xb8000000 0x04000000>; /* 64M */
-		};
-
-		ramoops@bc000000 {
+		ramoops@b3e00000 {
 			compatible = "ramoops";
-			reg = <0xbc000000 0x200000>; /* 16 * (4 * 0x8000) */
+			reg = <0xb3e00000 0x200000>; /* 16 * (4 * 0x8000) */
 			record-size = <0x8000>;
 			console-size = <0x8000>;
 			ftrace-size = <0x8000>;
@@ -110,6 +55,13 @@
 			max-reason = <3>; /* KMSG_DUMP_EMERG */
 		};
 
+		/* LPC FW cycle bridge region requires natural alignment */
+		flash_memory: region@b4000000 {
+			no-map;
+			reg = <0xb4000000 0x04000000>; /* 64M */
+		};
+
+		/* VGA region is dictated by hardware strapping */
 		vga_memory: region@bf000000 {
 			no-map;
 			compatible = "shared-dma-pool";
@@ -157,70 +109,68 @@
 		compatible = "gpio-leds";
 
 		/* BMC Card fault LED at the back */
-		bmc-ingraham0 {
+		led-bmc-ingraham0 {
 			gpios = <&gpio0 ASPEED_GPIO(H, 1) GPIO_ACTIVE_LOW>;
 		};
 
 		/* Enclosure ID LED at the back */
-		rear-enc-id0 {
+		led-rear-enc-id0 {
 			gpios = <&gpio0 ASPEED_GPIO(H, 2) GPIO_ACTIVE_LOW>;
 		};
 
 		/* Enclosure fault LED at the back */
-		rear-enc-fault0 {
+		led-rear-enc-fault0 {
 			gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>;
 		};
 
 		/* PCIE slot power LED */
-		pcieslot-power {
+		led-pcieslot-power {
 			gpios = <&gpio0 ASPEED_GPIO(P, 4) GPIO_ACTIVE_LOW>;
 		};
 	};
 
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		poll-interval = <1000>;
 
-		fan0-presence {
+		event-fan0-presence {
 			label = "fan0-presence";
 			gpios = <&pca0 6 GPIO_ACTIVE_LOW>;
 			linux,code = <6>;
 		};
 
-		fan1-presence {
+		event-fan1-presence {
 			label = "fan1-presence";
 			gpios = <&pca0 7 GPIO_ACTIVE_LOW>;
 			linux,code = <7>;
 		};
 
-		fan2-presence {
+		event-fan2-presence {
 			label = "fan2-presence";
 			gpios = <&pca0 8 GPIO_ACTIVE_LOW>;
 			linux,code = <8>;
 		};
 
-		fan3-presence {
+		event-fan3-presence {
 			label = "fan3-presence";
 			gpios = <&pca0 9 GPIO_ACTIVE_LOW>;
 			linux,code = <9>;
 		};
 
-		fan4-presence {
+		event-fan4-presence {
 			label = "fan4-presence";
 			gpios = <&pca0 10 GPIO_ACTIVE_LOW>;
 			linux,code = <10>;
 		};
 
-		fan5-presence {
+		event-fan5-presence {
 			label = "fan5-presence";
 			gpios = <&pca0 11 GPIO_ACTIVE_LOW>;
 			linux,code = <11>;
 		};
 	};
 
-	iio-hwmon-battery {
+	iio-hwmon {
 		compatible = "iio-hwmon";
 		io-channels = <&adc1 7>;
 	};
@@ -253,7 +203,7 @@
 	/*E0-E7*/	"","","","","","","","",
 	/*F0-F7*/	"","","rtc-battery-voltage-read-enable","reset-cause-pinhole","","","factory-reset-toggle","",
 	/*G0-G7*/	"","","","","","","","",
-	/*H0-H7*/	"","bmc-ingraham0","rear-enc-id0","rear-enc-fault0","","","","",
+	/*H0-H7*/	"","led-bmc-ingraham0","led-rear-enc-id0","led-rear-enc-fault0","","","","",
 	/*I0-I7*/	"","","","","","","bmc-secure-boot","",
 	/*J0-J7*/	"","","","","","","","",
 	/*K0-K7*/	"","","","","","","","",
@@ -261,11 +211,11 @@
 	/*M0-M7*/	"","","","","","","","",
 	/*N0-N7*/	"","","","","","","","",
 	/*O0-O7*/	"","","","usb-power","","","","",
-	/*P0-P7*/	"","","","","pcieslot-power","","","",
+	/*P0-P7*/	"","","","","led-pcieslot-power","","","",
 	/*Q0-Q7*/	"cfam-reset","","regulator-standby-faulted","","","","","",
 	/*R0-R7*/	"bmc-tpm-reset","power-chassis-control","power-chassis-good","","","","","",
 	/*S0-S7*/	"presence-ps0","presence-ps1","presence-ps2","presence-ps3",
-				"","","","",
+	"power-ffs-sync-history","","","",
 	/*T0-T7*/	"","","","","","","","",
 	/*U0-U7*/	"","","","","","","","",
 	/*V0-V7*/	"","","","","","","","",
@@ -274,14 +224,14 @@
 	/*Y0-Y7*/	"","","","","","","","",
 	/*Z0-Z7*/	"","","","","","","","";
 
-	i2c3_mux_oe_n {
+	i2c3-mux-oe-n-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(G, 6) GPIO_ACTIVE_LOW>;
 		output-high;
 		line-name = "I2C3_MUX_OE_N";
 	};
 
-	usb_power {
+	usb-power-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(O, 3) GPIO_ACTIVE_LOW>;
 		output-high;
@@ -301,612 +251,6 @@
 	clk-phase-mmc-hs200 = <180>, <180>;
 };
 
-&fsim0 {
-	status = "okay";
-
-	#address-cells = <2>;
-	#size-cells = <0>;
-
-	/*
-	 * CFAM Reset is supposed to be active low but pass1 hardware is wired
-	 * active high.
-	 */
-	cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_HIGH>;
-
-	cfam@0,0 {
-		reg = <0 0>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		chip-id = <0>;
-
-		scom@1000 {
-			compatible = "ibm,fsi2pib";
-			reg = <0x1000 0x400>;
-		};
-
-		i2c@1800 {
-			compatible = "ibm,fsi-i2c-master";
-			reg = <0x1800 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			cfam0_i2c0: i2c-bus@0 {
-				reg = <0>;	/* OMI01 */
-			};
-
-			cfam0_i2c1: i2c-bus@1 {
-				reg = <1>;	/* OMI23 */
-			};
-
-			cfam0_i2c10: i2c-bus@a {
-				reg = <10>;	/* OP3A */
-			};
-
-			cfam0_i2c11: i2c-bus@b {
-				reg = <11>;	/* OP3B */
-			};
-
-			cfam0_i2c12: i2c-bus@c {
-				reg = <12>;	/* OP4A */
-			};
-
-			cfam0_i2c13: i2c-bus@d {
-				reg = <13>;	/* OP4B */
-			};
-
-			cfam0_i2c14: i2c-bus@e {
-				reg = <14>;	/* OP5A */
-			};
-
-			cfam0_i2c15: i2c-bus@f {
-				reg = <15>;	/* OP5B */
-			};
-		};
-
-		fsi2spi@1c00 {
-			compatible = "ibm,fsi2spi";
-			reg = <0x1c00 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			cfam0_spi0: spi@0 {
-				reg = <0x0>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
-
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
-				};
-			};
-
-			cfam0_spi1: spi@20 {
-				reg = <0x20>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
-
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
-				};
-			};
-
-			cfam0_spi2: spi@40 {
-				reg = <0x40>;
-				compatible = "ibm,fsi2spi-restricted";
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
-
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
-				};
-			};
-
-			cfam0_spi3: spi@60 {
-				reg = <0x60>;
-				compatible = "ibm,fsi2spi-restricted";
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
-
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
-				};
-			};
-                };
-
-		sbefifo@2400 {
-			compatible = "ibm,p9-sbefifo";
-			reg = <0x2400 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			fsi_occ0: occ {
-				compatible = "ibm,p10-occ";
-			};
-		};
-
-		fsi_hub0: hub@3400 {
-			compatible = "fsi-master-hub";
-			reg = <0x3400 0x400>;
-			#address-cells = <2>;
-			#size-cells = <0>;
-		};
-	};
-};
-
-&fsi_hub0 {
-	cfam@1,0 {
-		reg = <1 0>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		chip-id = <1>;
-
-		scom@1000 {
-			compatible = "ibm,fsi2pib";
-			reg = <0x1000 0x400>;
-		};
-
-		i2c@1800 {
-			compatible = "ibm,fsi-i2c-master";
-			reg = <0x1800 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			cfam1_i2c2: i2c-bus@2 {
-				reg = <2>;	/* OMI45 */
-			};
-
-			cfam1_i2c3: i2c-bus@3 {
-				reg = <3>;	/* OMI67 */
-			};
-
-			cfam1_i2c10: i2c-bus@a {
-				reg = <10>;	/* OP3A */
-			};
-
-			cfam1_i2c11: i2c-bus@b {
-				reg = <11>;	/* OP3B */
-			};
-
-			cfam1_i2c14: i2c-bus@e {
-				reg = <14>;	/* OP5A */
-			};
-
-			cfam1_i2c15: i2c-bus@f {
-				reg = <15>;	/* OP5B */
-			};
-
-			cfam1_i2c16: i2c-bus@10 {
-				reg = <16>;	/* OP6A */
-			};
-
-			cfam1_i2c17: i2c-bus@11 {
-				reg = <17>;	/* OP6B */
-			};
-		};
-
-		fsi2spi@1c00 {
-			compatible = "ibm,fsi2spi";
-			reg = <0x1c00 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			cfam1_spi0: spi@0 {
-				reg = <0x0>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
-
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
-				};
-			};
-
-			cfam1_spi1: spi@20 {
-				reg = <0x20>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
-
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
-				};
-			};
-
-			cfam1_spi2: spi@40 {
-				reg = <0x40>;
-				compatible = "ibm,fsi2spi-restricted";
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
-
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
-				};
-			};
-
-			cfam1_spi3: spi@60 {
-				reg = <0x60>;
-				compatible = "ibm,fsi2spi-restricted";
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
-
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
-				};
-			};
-                };
-
-		sbefifo@2400 {
-			compatible = "ibm,p9-sbefifo";
-			reg = <0x2400 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			fsi_occ1: occ {
-				compatible = "ibm,p10-occ";
-			};
-		};
-
-		fsi_hub1: hub@3400 {
-			compatible = "fsi-master-hub";
-			reg = <0x3400 0x400>;
-			#address-cells = <2>;
-			#size-cells = <0>;
-
-			no-scan-on-init;
-		};
-	};
-
-	cfam@2,0 {
-		reg = <2 0>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		chip-id = <2>;
-
-		scom@1000 {
-			compatible = "ibm,fsi2pib";
-			reg = <0x1000 0x400>;
-		};
-
-		i2c@1800 {
-			compatible = "ibm,fsi-i2c-master";
-			reg = <0x1800 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			cfam2_i2c0: i2c-bus@0 {
-				reg = <0>;	/* OM01 */
-			};
-
-			cfam2_i2c1: i2c-bus@1 {
-				reg = <1>;	/* OM23 */
-			};
-
-			cfam2_i2c10: i2c-bus@a {
-				reg = <10>;	/* OP3A */
-			};
-
-			cfam2_i2c11: i2c-bus@b {
-				reg = <11>;	/* OP3B */
-			};
-
-			cfam2_i2c12: i2c-bus@c {
-				reg = <12>;	/* OP4A */
-			};
-
-			cfam2_i2c13: i2c-bus@d {
-				reg = <13>;	/* OP4B */
-			};
-
-			cfam2_i2c14: i2c-bus@e {
-				reg = <14>;	/* OP5A */
-			};
-
-			cfam2_i2c15: i2c-bus@f {
-				reg = <15>;	/* OP5B */
-			};
-		};
-
-		fsi2spi@1c00 {
-			compatible = "ibm,fsi2spi";
-			reg = <0x1c00 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			cfam2_spi0: spi@0 {
-				reg = <0x0>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
-
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
-				};
-			};
-
-			cfam2_spi1: spi@20 {
-				reg = <0x20>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
-
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
-				};
-			};
-
-			cfam2_spi2: spi@40 {
-				reg = <0x40>;
-				compatible = "ibm,fsi2spi-restricted";
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
-
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
-				};
-			};
-
-			cfam2_spi3: spi@60 {
-				reg = <0x60>;
-				compatible = "ibm,fsi2spi-restricted";
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
-
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
-				};
-			};
-		};
-
-		sbefifo@2400 {
-			compatible = "ibm,p9-sbefifo";
-			reg = <0x2400 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			fsi_occ2: occ {
-				compatible = "ibm,p10-occ";
-			};
-		};
-
-		fsi_hub2: hub@3400 {
-			compatible = "fsi-master-hub";
-			reg = <0x3400 0x400>;
-			#address-cells = <2>;
-			#size-cells = <0>;
-
-			no-scan-on-init;
-		};
-	};
-
-	cfam@3,0 {
-		reg = <3 0>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		chip-id = <3>;
-
-		scom@1000 {
-			compatible = "ibm,fsi2pib";
-			reg = <0x1000 0x400>;
-		};
-
-		i2c@1800 {
-			compatible = "ibm,fsi-i2c-master";
-			reg = <0x1800 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			cfam3_i2c2: i2c-bus@2 {
-				reg = <2>;	/* OM45 */
-			};
-
-			cfam3_i2c3: i2c-bus@3 {
-				reg = <3>;	/* OM67 */
-			};
-
-			cfam3_i2c10: i2c-bus@a {
-				reg = <10>;	/* OP3A */
-			};
-
-			cfam3_i2c11: i2c-bus@b {
-				reg = <11>;	/* OP3B */
-			};
-
-			cfam3_i2c14: i2c-bus@e {
-				reg = <14>;	/* OP5A */
-			};
-
-			cfam3_i2c15: i2c-bus@f {
-				reg = <15>;	/* OP5B */
-			};
-
-			cfam3_i2c16: i2c-bus@10 {
-				reg = <16>;	/* OP6A */
-			};
-
-			cfam3_i2c17: i2c-bus@11 {
-				reg = <17>;	/* OP6B */
-			};
-		};
-
-		fsi2spi@1c00 {
-			compatible = "ibm,fsi2spi";
-			reg = <0x1c00 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			cfam3_spi0: spi@0 {
-				reg = <0x0>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
-
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
-				};
-			};
-
-			cfam3_spi1: spi@20 {
-				reg = <0x20>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
-
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
-				};
-			};
-
-			cfam3_spi2: spi@40 {
-				reg = <0x40>;
-				compatible = "ibm,fsi2spi-restricted";
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
-
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
-				};
-			};
-
-			cfam3_spi3: spi@60 {
-				reg = <0x60>;
-				compatible = "ibm,fsi2spi-restricted";
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				eeprom@0 {
-					at25,byte-len = <0x80000>;
-					at25,addr-mode = <4>;
-					at25,page-size = <256>;
-
-					compatible = "atmel,at25";
-					reg = <0>;
-					spi-max-frequency = <1000000>;
-				};
-			};
-		};
-
-		sbefifo@2400 {
-			compatible = "ibm,p9-sbefifo";
-			reg = <0x2400 0x400>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			fsi_occ3: occ {
-				compatible = "ibm,p10-occ";
-			};
-		};
-
-		fsi_hub3: hub@3400 {
-			compatible = "fsi-master-hub";
-			reg = <0x3400 0x400>;
-			#address-cells = <2>;
-			#size-cells = <0>;
-
-			no-scan-on-init;
-		};
-	};
-};
-
-/* Legacy OCC numbering (to get rid of when userspace is fixed) */
-&fsi_occ0 {
-	reg = <1>;
-};
-
-&fsi_occ1 {
-	reg = <2>;
-};
-
-&fsi_occ2 {
-	reg = <3>;
-};
-
-&fsi_occ3 {
-	reg = <4>;
-};
-
 &ibt {
 	status = "okay";
 };
@@ -919,7 +263,7 @@
 		reg = <0x51>;
 	};
 
-	tca_pres1: tca9554@20{
+	tca_pres1: tca9554@20 {
 		compatible = "ti,tca9554";
 		reg = <0x20>;
 		#address-cells = <1>;
@@ -997,33 +341,7 @@
 		reg = <0x4a>;
 	};
 
-	pca9551@60 {
-		compatible = "nxp,pca9551";
-		reg = <0x60>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		led@0 {
-			label = "cablecard0-cxp-top";
-			reg = <0>;
-			retain-state-shutdown;
-			default-state = "keep";
-			type = <PCA955X_TYPE_LED>;
-		};
-
-		led@1 {
-			label = "cablecard0-cxp-bot";
-			reg = <1>;
-			retain-state-shutdown;
-			default-state = "keep";
-			type = <PCA955X_TYPE_LED>;
-		};
-	};
-
-	pca9546@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		reg = <0x70>;
 		#address-cells = <1>;
@@ -1040,6 +358,32 @@
 				compatible = "atmel,24c64";
 				reg = <0x50>;
 			};
+
+			pca9551@60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard0-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard0-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
 		};
 
 		i2c4mux0chn1: i2c@1 {
@@ -1079,59 +423,7 @@
 		reg = <0x49>;
 	};
 
-	pca9551@60 {
-		compatible = "nxp,pca9551";
-		reg = <0x60>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		led@0 {
-			label = "cablecard3-cxp-top";
-			reg = <0>;
-			retain-state-shutdown;
-			default-state = "keep";
-			type = <PCA955X_TYPE_LED>;
-		};
-
-		led@1 {
-			label = "cablecard3-cxp-bot";
-			reg = <1>;
-			retain-state-shutdown;
-			default-state = "keep";
-			type = <PCA955X_TYPE_LED>;
-		};
-	};
-
-	pca9551@61 {
-		compatible = "nxp,pca9551";
-		reg = <0x61>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		led@0 {
-			label = "cablecard4-cxp-top";
-			reg = <0>;
-			retain-state-shutdown;
-			default-state = "keep";
-			type = <PCA955X_TYPE_LED>;
-		};
-
-		led@1 {
-			label = "cablecard4-cxp-bot";
-			reg = <1>;
-			retain-state-shutdown;
-			default-state = "keep";
-			type = <PCA955X_TYPE_LED>;
-		};
-	};
-
-	pca9546@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		reg = <0x70>;
 		#address-cells = <1>;
@@ -1148,6 +440,32 @@
 				compatible = "atmel,24c64";
 				reg = <0x50>;
 			};
+
+			pca9551@60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard3-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard3-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
 		};
 
 		i2c5mux0chn1: i2c@1 {
@@ -1159,6 +477,32 @@
 				compatible = "atmel,24c64";
 				reg = <0x51>;
 			};
+
+			pca9551@61 {
+				compatible = "nxp,pca9551";
+				reg = <0x61>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard4-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard4-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
 		};
 	};
 };
@@ -1181,7 +525,7 @@
 		reg = <0x4b>;
 	};
 
-	pca9546@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		reg = <0x70>;
 		#address-cells = <1>;
@@ -1936,8 +1280,9 @@
 		#gpio-cells = <2>;
 
 		gpio-line-names =
-			"", "", "", "", "", "", "", "",
-			"", "", "", "", "", "", "power-config-full-load", "";
+			"", "", "", "", "", "", "P10_DCM0_PRES", "P10_DCM1_PRES",
+			"", "", "", "", "PRESENT_VRM_DCM0_N", "PRESENT_VRM_DCM1_N",
+			"power-config-full-load", "";
 	};
 
 	pca_pres2: pca9552@61 {
@@ -2011,33 +1356,7 @@
 		reg = <0x49>;
 	};
 
-	pca9551@60 {
-		compatible = "nxp,pca9551";
-		reg = <0x60>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		led@0 {
-			label = "cablecard10-cxp-top";
-			reg = <0>;
-			retain-state-shutdown;
-			default-state = "keep";
-			type = <PCA955X_TYPE_LED>;
-		};
-
-		led@1 {
-			label = "cablecard10-cxp-bot";
-			reg = <1>;
-			retain-state-shutdown;
-			default-state = "keep";
-			type = <PCA955X_TYPE_LED>;
-		};
-	};
-
-	pca9546@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		reg = <0x70>;
 		#address-cells = <1>;
@@ -2054,6 +1373,32 @@
 				compatible = "atmel,24c64";
 				reg = <0x50>;
 			};
+
+			pca9551@60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "cablecard10-cxp-top";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "cablecard10-cxp-bot";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
 		};
 
 		i2c11mux0chn1: i2c@1 {
@@ -2072,11 +1417,6 @@
 &i2c12 {
 	status = "okay";
 
-	tpm@2e {
-		compatible = "nuvoton,npct75x";
-		reg = <0x2e>;
-	};
-
 	eeprom@50 {
 		compatible = "atmel,24c64";
 		reg = <0x50>;
@@ -2332,6 +1672,10 @@
 	};
 };
 
+&uart2 {
+	status = "okay";
+};
+
 &vuart1 {
 	status = "okay";
 };
@@ -2379,11 +1723,6 @@
 	status = "okay";
 };
 
-&xdma {
-	status = "okay";
-	memory-region = <&vga_memory>;
-};
-
 &kcs2 {
 	status = "okay";
 	aspeed,lpc-io-reg = <0xca8 0xcac>;
@@ -2394,3 +1733,5 @@
 	aspeed,lpc-io-reg = <0xca2>;
 	aspeed,lpc-interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
 };
+
+#include "ibm-power10-quad.dtsi"
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dts
new file mode 100644
index 000000000000..dbadba8eb698
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-sbp1.dts
@@ -0,0 +1,6086 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright 2024 IBM Corp.
+/dts-v1/;
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/i2c/i2c.h>
+#include "aspeed-g6.dtsi"
+
+/ {
+	model = "IBM SBP1";
+	compatible = "ibm,sbp1-bmc", "aspeed,ast2600";
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x20000000>;
+		device_type = "memory";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		gfx_memory: framebuffer {
+			size = <0x01000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power {
+			label = "LED_BMC_READY";
+			gpios = <&gpio0 ASPEED_GPIO(H, 1) GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			retain-state-suspended;
+			panic-indicator;
+		};
+
+		led-id-tpm {
+			label = "LED_ID_TPM";
+			gpios = <&smb_pex_vr_ctrl 12 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-bat {
+			label = "LED_ID_BAT";
+			gpios = <&smb_pex_vr_ctrl 16 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-mgmt-port2 {
+			label = "LED_ID_MGMT_PORT2";
+			gpios = <&smb_pex_vr_ctrl 17 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-mgmt-port1 {
+			label = "LED_ID_MGMT_PORT1";
+			gpios = <&smb_pex_vr_ctrl 18 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-nic1-port1 {
+			label = "LED_ID_NIC1_PORT1";
+			gpios = <&smb_pex_vr_ctrl 22 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-nic1-port2 {
+			label = "LED_ID_NIC1_PORT2";
+			gpios = <&smb_pex_vr_ctrl 23 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-nic2-port1 {
+			label = "LED_ID_NIC2_PORT1";
+			gpios = <&smb_pex_vr_ctrl 24 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-nic2-port2 {
+			label = "LED_ID_NIC2_PORT2";
+			gpios = <&smb_pex_vr_ctrl 25 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-m2-ssd2 {
+			label = "LED_ID_M2_SSD2";
+			gpios = <&smb_pex_vr_ctrl 36 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-m2-ssd1 {
+			label = "LED_ID_M2_SSD1";
+			gpios = <&smb_pex_vr_ctrl 37 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dwr-frnt-p {
+			label = "LED_ID_DWR_FRNT_P";
+			gpios = <&smb_svc_pex_cpu3_led 37 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_BLUE>;
+
+			default-state = "on";
+			retain-state-suspended;
+			retain-state-shutdown;
+		};
+
+		led-pwr-dwr-frnt {
+			label = "LED_PWR_DWR_FRNT";
+			gpios = <&smb_svc_pex_cpu3_led 36 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_GREEN>;
+
+			retain-state-suspended;
+			retain-state-shutdown;
+		};
+
+		led-pwr-dwr-back {
+			label = "LED_PWR_DWR_BACK";
+			gpios = <&smb_pex_vr_ctrl 34 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_GREEN>;
+
+			retain-state-suspended;
+			retain-state-shutdown;
+		};
+
+		led-id-dwr-back-p {
+			label = "LED_ID_DWR_BACK_P";
+			gpios = <&smb_pex_vr_ctrl 35 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_BLUE>;
+
+			default-state = "on";
+			retain-state-suspended;
+			retain-state-shutdown;
+		};
+
+		led-id-cpu0 {
+			label = "LED_ID_CPU0";
+			gpios = <&smb_svc_pex_cpu0_led 39 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-cpu1 {
+			label = "LED_ID_CPU1";
+			gpios = <&smb_svc_pex_cpu1_led 39 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-cpu2 {
+			label = "LED_ID_CPU2";
+			gpios = <&smb_svc_pex_cpu2_led 39 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-cpu3 {
+			label = "LED_ID_CPU3";
+			gpios = <&smb_svc_pex_cpu3_led 39 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c0e2 {
+			label = "LED_ID_DIMM_C0E2";
+			gpios = <&smb_svc_pex_cpu0_led 20 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c0e1 {
+			label = "LED_ID_DIMM_C0E1";
+			gpios = <&smb_svc_pex_cpu0_led 21 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c0f2 {
+			label = "LED_ID_DIMM_C0F2";
+			gpios = <&smb_svc_pex_cpu0_led 22 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c0f1 {
+			label = "LED_ID_DIMM_C0F1";
+			gpios = <&smb_svc_pex_cpu0_led 23 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c0g2 {
+			label = "LED_ID_DIMM_C0G2";
+			gpios = <&smb_svc_pex_cpu0_led 24 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c0g1 {
+			label = "LED_ID_DIMM_C0G1";
+			gpios = <&smb_svc_pex_cpu0_led 25 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c0h2 {
+			label = "LED_ID_DIMM_C0H2";
+			gpios = <&smb_svc_pex_cpu0_led 26 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c0h1 {
+			label = "LED_ID_DIMM_C0H1";
+			gpios = <&smb_svc_pex_cpu0_led 27 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c0a2 {
+			label = "LED_ID_DIMM_C0A2";
+			gpios = <&smb_svc_pex_cpu0_led 28 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c0a1 {
+			label = "LED_ID_DIMM_C0A1";
+			gpios = <&smb_svc_pex_cpu0_led 29 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c0b2 {
+			label = "LED_ID_DIMM_C0B2";
+			gpios = <&smb_svc_pex_cpu0_led 30 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c0b1 {
+			label = "LED_ID_DIMM_C0B1";
+			gpios = <&smb_svc_pex_cpu0_led 31 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c0c2 {
+			label = "LED_ID_DIMM_C0C2";
+			gpios = <&smb_svc_pex_cpu0_led 32 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c0c1 {
+			label = "LED_ID_DIMM_C0C1";
+			gpios = <&smb_svc_pex_cpu0_led 33 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c0d2 {
+			label = "LED_ID_DIMM_C0D2";
+			gpios = <&smb_svc_pex_cpu0_led 34 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c0d1 {
+			label = "LED_ID_DIMM_C0D1";
+			gpios = <&smb_svc_pex_cpu0_led 35 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c1e2 {
+			label = "LED_ID_DIMM_C1E2";
+			gpios = <&smb_svc_pex_cpu1_led 20 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c1e1 {
+			label = "LED_ID_DIMM_C1E1";
+			gpios = <&smb_svc_pex_cpu1_led 21 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c1f2 {
+			label = "LED_ID_DIMM_C1F2";
+			gpios = <&smb_svc_pex_cpu1_led 22 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c1f1 {
+			label = "LED_ID_DIMM_C1F1";
+			gpios = <&smb_svc_pex_cpu1_led 23 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c1g2 {
+			label = "LED_ID_DIMM_C1G2";
+			gpios = <&smb_svc_pex_cpu1_led 24 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c1g1 {
+			label = "LED_ID_DIMM_C1G1";
+			gpios = <&smb_svc_pex_cpu1_led 25 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c1h2 {
+			label = "LED_ID_DIMM_C1H2";
+			gpios = <&smb_svc_pex_cpu1_led 26 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c1h1 {
+			label = "LED_ID_DIMM_C1H1";
+			gpios = <&smb_svc_pex_cpu1_led 27 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c1a2 {
+			label = "LED_ID_DIMM_C1A2";
+			gpios = <&smb_svc_pex_cpu1_led 28 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c1a1 {
+			label = "LED_ID_DIMM_C1A1";
+			gpios = <&smb_svc_pex_cpu1_led 29 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c1b2 {
+			label = "LED_ID_DIMM_C1B2";
+			gpios = <&smb_svc_pex_cpu1_led 30 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c1b1 {
+			label = "LED_ID_DIMM_C1B1";
+			gpios = <&smb_svc_pex_cpu1_led 31 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c1c2 {
+			label = "LED_ID_DIMM_C1C2";
+			gpios = <&smb_svc_pex_cpu1_led 32 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c1c1 {
+			label = "LED_ID_DIMM_C1C1";
+			gpios = <&smb_svc_pex_cpu1_led 33 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c1d2 {
+			label = "LED_ID_DIMM_C1D2";
+			gpios = <&smb_svc_pex_cpu1_led 34 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c1d1 {
+			label = "LED_ID_DIMM_C1D1";
+			gpios = <&smb_svc_pex_cpu1_led 35 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c2e2 {
+			label = "LED_ID_DIMM_C2E2";
+			gpios = <&smb_svc_pex_cpu2_led 20 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c2e1 {
+			label = "LED_ID_DIMM_C2E1";
+			gpios = <&smb_svc_pex_cpu2_led 21 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c2f2 {
+			label = "LED_ID_DIMM_C2F2";
+			gpios = <&smb_svc_pex_cpu2_led 22 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c2f1 {
+			label = "LED_ID_DIMM_C2F1";
+			gpios = <&smb_svc_pex_cpu2_led 23 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c2g2 {
+			label = "LED_ID_DIMM_C2G2";
+			gpios = <&smb_svc_pex_cpu2_led 24 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c2g1 {
+			label = "LED_ID_DIMM_C2G1";
+			gpios = <&smb_svc_pex_cpu2_led 25 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c2h2 {
+			label = "LED_ID_DIMM_C2H2";
+			gpios = <&smb_svc_pex_cpu2_led 26 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c2h1 {
+			label = "LED_ID_DIMM_C2H1";
+			gpios = <&smb_svc_pex_cpu2_led 27 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c2a2 {
+			label = "LED_ID_DIMM_C2A2";
+			gpios = <&smb_svc_pex_cpu2_led 28 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c2a1 {
+			label = "LED_ID_DIMM_C2A1";
+			gpios = <&smb_svc_pex_cpu2_led 29 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c2b2 {
+			label = "LED_ID_DIMM_C2B2";
+			gpios = <&smb_svc_pex_cpu2_led 30 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c2b1 {
+			label = "LED_ID_DIMM_C2B1";
+			gpios = <&smb_svc_pex_cpu2_led 31 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c2c2 {
+			label = "LED_ID_DIMM_C2C2";
+			gpios = <&smb_svc_pex_cpu2_led 32 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c2c1 {
+			label = "LED_ID_DIMM_C2C1";
+			gpios = <&smb_svc_pex_cpu2_led 33 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c2d2 {
+			label = "LED_ID_DIMM_C2D2";
+			gpios = <&smb_svc_pex_cpu2_led 34 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c2d1 {
+			label = "LED_ID_DIMM_C2D1";
+			gpios = <&smb_svc_pex_cpu2_led 35 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c3e2 {
+			label = "LED_ID_DIMM_C3E2";
+			gpios = <&smb_svc_pex_cpu3_led 20 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c3e1 {
+			label = "LED_ID_DIMM_C3E1";
+			gpios = <&smb_svc_pex_cpu3_led 21 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c3f2 {
+			label = "LED_ID_DIMM_C3F2";
+			gpios = <&smb_svc_pex_cpu3_led 22 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c3f1 {
+			label = "LED_ID_DIMM_C3F1";
+			gpios = <&smb_svc_pex_cpu3_led 23 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c3g2 {
+			label = "LED_ID_DIMM_C3G2";
+			gpios = <&smb_svc_pex_cpu3_led 24 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c3g1 {
+			label = "LED_ID_DIMM_C3G1";
+			gpios = <&smb_svc_pex_cpu3_led 25 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c3h2 {
+			label = "LED_ID_DIMM_C3H2";
+			gpios = <&smb_svc_pex_cpu3_led 26 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c3h1 {
+			label = "LED_ID_DIMM_C3H1";
+			gpios = <&smb_svc_pex_cpu3_led 27 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c3a2 {
+			label = "LED_ID_DIMM_C3A2";
+			gpios = <&smb_svc_pex_cpu3_led 28 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c3a1 {
+			label = "LED_ID_DIMM_C3A1";
+			gpios = <&smb_svc_pex_cpu3_led 29 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c3b2 {
+			label = "LED_ID_DIMM_C3B2";
+			gpios = <&smb_svc_pex_cpu3_led 30 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c3b1 {
+			label = "LED_ID_DIMM_C3B1";
+			gpios = <&smb_svc_pex_cpu3_led 31 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c3c2 {
+			label = "LED_ID_DIMM_C3C2";
+			gpios = <&smb_svc_pex_cpu3_led 32 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c3c1 {
+			label = "LED_ID_DIMM_C3C1";
+			gpios = <&smb_svc_pex_cpu3_led 33 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c3d2 {
+			label = "LED_ID_DIMM_C3D2";
+			gpios = <&smb_svc_pex_cpu3_led 34 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-c3d1 {
+			label = "LED_ID_DIMM_C3D1";
+			gpios = <&smb_svc_pex_cpu3_led 35 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd01 {
+			label = "LED_ID_RSSD01";
+			gpios = <&smb_svc_pex_rssd01_16 0 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd02 {
+			label = "LED_ID_RSSD02";
+			gpios = <&smb_svc_pex_rssd01_16 1 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd03 {
+			label = "LED_ID_RSSD03";
+			gpios = <&smb_svc_pex_rssd01_16 2 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd04 {
+			label = "LED_ID_RSSD04";
+			gpios = <&smb_svc_pex_rssd01_16 3 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd05 {
+			label = "LED_ID_RSSD05";
+			gpios = <&smb_svc_pex_rssd01_16 4 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd06 {
+			label = "LED_ID_RSSD06";
+			gpios = <&smb_svc_pex_rssd01_16 5 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd07 {
+			label = "LED_ID_RSSD07";
+			gpios = <&smb_svc_pex_rssd01_16 6 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd08 {
+			label = "LED_ID_RSSD08";
+			gpios = <&smb_svc_pex_rssd01_16 7 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd09 {
+			label = "LED_ID_RSSD09";
+			gpios = <&smb_svc_pex_rssd01_16 8 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd10 {
+			label = "LED_ID_RSSD10";
+			gpios = <&smb_svc_pex_rssd01_16 9 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd11 {
+			label = "LED_ID_RSSD11";
+			gpios = <&smb_svc_pex_rssd01_16 10 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd12 {
+			label = "LED_ID_RSSD12";
+			gpios = <&smb_svc_pex_rssd01_16 11 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd13 {
+			label = "LED_ID_RSSD13";
+			gpios = <&smb_svc_pex_rssd01_16 12 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd14 {
+			label = "LED_ID_RSSD14";
+			gpios = <&smb_svc_pex_rssd01_16 13 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd15 {
+			label = "LED_ID_RSSD15";
+			gpios = <&smb_svc_pex_rssd01_16 14 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd16 {
+			label = "LED_ID_RSSD16";
+			gpios = <&smb_svc_pex_rssd01_16 15 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd17 {
+			label = "LED_ID_RSSD17";
+			gpios = <&smb_svc_pex_rssd17_32 0 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd18 {
+			label = "LED_ID_RSSD18";
+			gpios = <&smb_svc_pex_rssd17_32 1 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd19 {
+			label = "LED_ID_RSSD19";
+			gpios = <&smb_svc_pex_rssd17_32 2 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd20 {
+			label = "LED_ID_RSSD20";
+			gpios = <&smb_svc_pex_rssd17_32 3 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd21 {
+			label = "LED_ID_RSSD21";
+			gpios = <&smb_svc_pex_rssd17_32 4 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd22 {
+			label = "LED_ID_RSSD22";
+			gpios = <&smb_svc_pex_rssd17_32 5 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd23 {
+			label = "LED_ID_RSSD23";
+			gpios = <&smb_svc_pex_rssd17_32 6 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd24 {
+			label = "LED_ID_RSSD24";
+			gpios = <&smb_svc_pex_rssd17_32 7 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd25 {
+			label = "LED_ID_RSSD25";
+			gpios = <&smb_svc_pex_rssd17_32 8 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd26 {
+			label = "LED_ID_RSSD26";
+			gpios = <&smb_svc_pex_rssd17_32 9 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd27 {
+			label = "LED_ID_RSSD27";
+			gpios = <&smb_svc_pex_rssd17_32 10 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd28 {
+			label = "LED_ID_RSSD28";
+			gpios = <&smb_svc_pex_rssd17_32 11 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd29 {
+			label = "LED_ID_RSSD29";
+			gpios = <&smb_svc_pex_rssd17_32 12 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd30 {
+			label = "LED_ID_RSSD30";
+			gpios = <&smb_svc_pex_rssd17_32 13 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd31 {
+			label = "LED_ID_RSSD31";
+			gpios = <&smb_svc_pex_rssd17_32 14 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-dimm-rssd32 {
+			label = "LED_ID_RSSD32";
+			gpios = <&smb_svc_pex_rssd17_32 15 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-fan-asm01 {
+			label = "LED_ID_FAN_ASM01";
+			gpios = <&smb_svc_pex_rssd01_16 32 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-fan-asm02 {
+			label = "LED_ID_FAN_ASM02";
+			gpios = <&smb_svc_pex_rssd01_16 33 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-fan-asm03 {
+			label = "LED_ID_FAN_ASM03";
+			gpios = <&smb_svc_pex_rssd01_16 34 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-fan-asm04 {
+			label = "LED_ID_FAN_ASM04";
+			gpios = <&smb_svc_pex_rssd01_16 35 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-fan-asm05 {
+			label = "LED_ID_FAN_ASM05";
+			gpios = <&smb_svc_pex_rssd01_16 36 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-fan-asm06 {
+			label = "LED_ID_FAN_ASM06";
+			gpios = <&smb_svc_pex_rssd01_16 37 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-fan-asm07 {
+			label = "LED_ID_FAN_ASM07";
+			gpios = <&smb_svc_pex_rssd17_32 32 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-fan-asm08 {
+			label = "LED_ID_FAN_ASM08";
+			gpios = <&smb_svc_pex_rssd17_32 33 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-fan-asm09 {
+			label = "LED_ID_FAN_ASM09";
+			gpios = <&smb_svc_pex_rssd17_32 34 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-fan-asm10 {
+			label = "LED_ID_FAN_ASM10";
+			gpios = <&smb_svc_pex_rssd17_32 35 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-fan-asm11 {
+			label = "LED_ID_FAN_ASM11";
+			gpios = <&smb_svc_pex_rssd17_32 36 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+
+		led-id-fan-asm12 {
+			label = "LED_ID_FAN_ASM12";
+			gpios = <&smb_svc_pex_rssd17_32 37 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_YELLOW>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&p12v_vd 0>, <&p5v_aux_vd 0>, <&p5v_bmc_aux_vd 0>, <&p3v3_aux_vd 0>,
+			<&p3v3_bmc_aux_vd 0>, <&p1v8_bmc_aux_vd 0>, <&adc1 4>, <&adc0 2>, <&adc1 0>,
+			<&p2V5_aux_vd 0>, <&p3v3_rtc_vd 0>;
+	};
+
+	p12v_vd: voltage-divider1 {
+		compatible = "voltage-divider";
+		io-channels = <&adc1 3>;
+		#io-channel-cells = <1>;
+
+		/*
+		 * Scale the system voltage by 1127/127 to fit the ADC range.
+		 * Use small nominator to prevent integer overflow.
+		 */
+		output-ohms = <15>;
+		full-ohms = <133>;
+	};
+
+	p5v_aux_vd: voltage-divider2 {
+		compatible = "voltage-divider";
+		io-channels = <&adc1 5>;
+		#io-channel-cells = <1>;
+
+		/*
+		 * Scale the system voltage by 1365/365 to fit the ADC range.
+		 * Use small nominator to prevent integer overflow.
+		 */
+		output-ohms = <50>;
+		full-ohms = <187>;
+	};
+
+	p5v_bmc_aux_vd: voltage-divider3 {
+		compatible = "voltage-divider";
+		io-channels = <&adc0 3>;
+		#io-channel-cells = <1>;
+
+		/*
+		 * Scale the system voltage by 1365/365 to fit the ADC range.
+		 * Use small nominator to prevent integer overflow.
+		 */
+		output-ohms = <50>;
+		full-ohms = <187>;
+	};
+
+	p3v3_aux_vd: voltage-divider4 {
+		compatible = "voltage-divider";
+		io-channels = <&adc1 2>;
+		#io-channel-cells = <1>;
+
+		/*
+		 * Scale the system voltage by 1698/698 to fit the ADC range.
+		 * Use small nominator to prevent integer overflow.
+		 */
+		output-ohms = <14>;
+		full-ohms = <34>;
+	};
+
+	p3v3_bmc_aux_vd: voltage-divider5 {
+		compatible = "voltage-divider";
+		io-channels = <&adc0 7>;
+		#io-channel-cells = <1>;
+
+		/*
+		 * Scale the system voltage by 1698/698 to fit the ADC range.
+		 * Use small nominator to prevent integer overflow.
+		 */
+		output-ohms = <14>;
+		full-ohms = <34>;
+	};
+
+	p1v8_bmc_aux_vd: voltage-divider6 {
+		compatible = "voltage-divider";
+		io-channels = <&adc0 6>;
+		#io-channel-cells = <1>;
+
+		/*
+		 * Scale the system voltage by 4000/3000 to fit the ADC range.
+		 * Use small nominator to prevent integer overflow.
+		 */
+		output-ohms = <3>;
+		full-ohms = <4>;
+	};
+
+	p2V5_aux_vd: voltage-divider7 {
+		compatible = "voltage-divider";
+		io-channels = <&adc1 1>;
+		#io-channel-cells = <1>;
+
+		/*
+		 * Scale the system voltage by 2100/1100 to fit the ADC range.
+		 * Use small nominator to prevent integer overflow.
+		 */
+		output-ohms = <11>;
+		full-ohms = <21>;
+	};
+
+	p3v3_rtc_vd: voltage-divider8 {
+		compatible = "voltage-divider";
+		io-channels = <&adc1 7>;
+		#io-channel-cells = <1>;
+
+		/*
+		 * Scale the system voltage by 231000/100000 to fit the ADC range.
+		 * Use small nominator to prevent integer overflow.
+		 */
+		output-ohms = <100>;
+		full-ohms = <231>;
+	};
+
+	thermistor0: thermistor-0 {
+		compatible = "epcos,b57891s0103";
+		pullup-uv = <3300000>;
+		pullup-ohm = <10000>;
+		pulldown-ohm = <0>;
+		io-channels = <&adc0 0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	thermistor1: thermistor-1 {
+		compatible = "epcos,b57891s0103";
+		pullup-uv = <3300000>;
+		pullup-ohm = <10000>;
+		pulldown-ohm = <0>;
+		io-channels = <&adc0 1>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	thermistor2: thermistor-2 {
+		compatible = "epcos,b57891s0103";
+		pullup-uv = <3300000>;
+		pullup-ohm = <10000>;
+		pulldown-ohm = <0>;
+		io-channels = <&adc0 4>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	thermistor3: thermistor-3 {
+		compatible = "epcos,b57891s0103";
+		pullup-uv = <3300000>;
+		pullup-ohm = <10000>;
+		pulldown-ohm = <0>;
+		io-channels = <&adc0 5>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	p12v: fixedregulator-p12v {
+		compatible = "regulator-fixed";
+		regulator-name = "p12v";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	p3v3_bmc_aux: fixedregulator-p3v3-bmc-aux {
+		compatible = "regulator-fixed";
+		regulator-name = "p3v3_bmc_aux";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	p1v8_bmc_aux: fixedregulator-p1v8-bmc-aux {
+		compatible = "regulator-fixed";
+		regulator-name = "p1v8_bmc_aux";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	p1v2_bmc_aux: fixedregulator-p1v2-bmc-aux {
+		compatible = "regulator-fixed";
+		regulator-name = "p1v2_bmc_aux";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	p12v-a-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&p12v_a>;
+	};
+
+	p12v-b-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&p12v_b>;
+	};
+
+	p12v-c-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&p12v_c>;
+	};
+
+	p12v-d-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&p12v_d>;
+	};
+
+	pvccinfaon-cpu0-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvccinfaon_cpu0>;
+	};
+
+	pvccfa-ehv-cpu0-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvccfa_ehv_cpu0>;
+	};
+
+	pvnn-main-cpu0-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvnn_main_cpu0>;
+	};
+
+	pvccin-cpu0-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvccin_cpu0>;
+	};
+
+	pvccfa-ehv-fivra-cpu0-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvccfa_ehv_fivra_cpu0>;
+	};
+
+	pvccd-hv-cpu0-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvccd_hv_cpu0>;
+	};
+
+	pvpp-hbm-cpu0-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvpp_hbm_cpu0>;
+	};
+
+	pvccinfaon-cpu1-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvccinfaon_cpu1>;
+	};
+
+	pvccfa-ehv-cpu1-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvccfa_ehv_cpu1>;
+	};
+
+	pvnn-main-cpu1-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvnn_main_cpu1>;
+	};
+
+	pvccin-cpu1-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvccin_cpu1>;
+	};
+
+	pvccfa-ehv-fivra-cpu1-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvccfa_ehv_fivra_cpu1>;
+	};
+
+	pvccd-hv-cpu1-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvccd_hv_cpu1>;
+	};
+
+	pvpp-hbm-cpu1-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvpp_hbm_cpu1>;
+	};
+
+	pvccinfaon-cpu2-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvccinfaon_cpu2>;
+	};
+
+	pvccfa-ehv-cpu2-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvccfa_ehv_cpu2>;
+	};
+
+	pvnn-main-cpu2-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvnn_main_cpu2>;
+	};
+
+	pvccin-cpu2-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvccin_cpu2>;
+	};
+
+	pvccfa-ehv-fivra-cpu2-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvccfa_ehv_fivra_cpu2>;
+	};
+
+	pvccd-hv-cpu2-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvccd_hv_cpu2>;
+	};
+
+	pvpp-hbm-cpu2-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvpp_hbm_cpu2>;
+	};
+
+	pvccinfaon-cpu3-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvccinfaon_cpu3>;
+	};
+
+	pvccfa-ehv-cpu3-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvccfa_ehv_cpu3>;
+	};
+
+	pvnn-main-cpu3-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvnn_main_cpu3>;
+	};
+
+	pvccin-cpu3-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvccin_cpu3>;
+	};
+
+	pvccfa-ehv-fivra-cpu3-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvccfa_ehv_fivra_cpu3>;
+	};
+
+	pvccd-hv-cpu3-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvccd_hv_cpu3>;
+	};
+
+	pvpp-hbm-cpu3-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvpp_hbm_cpu3>;
+	};
+
+	p1v05-pch-aux-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&p1v05_pch_aux>;
+	};
+
+	p1v8-pch-aux-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&p1v8_pch_aux>;
+	};
+
+	p3v3-pch-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&p3v3_pch>;
+	};
+
+	p5v-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&p5v>;
+	};
+
+	smb-m2-ssb-ssd2 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_smb_m2_ssb_ssd2>;
+	};
+
+	smb-m2-ssb-ssd1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_smb_m2_ssb_ssd1>;
+	};
+
+	ssb-rssd01-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd01>;
+	};
+
+	ssb-rssd01-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd01>;
+	};
+
+	ssb-rssd02-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd02>;
+	};
+
+	ssb-rssd02-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd02>;
+	};
+
+	ssb-rssd03-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd03>;
+	};
+
+	ssb-rssd03-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd03>;
+	};
+
+	ssb-rssd04-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd04>;
+	};
+
+	ssb-rssd04-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd04>;
+	};
+
+	ssb-rssd05-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd05>;
+	};
+
+	ssb-rssd05-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd05>;
+	};
+
+	ssb-rssd06-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd06>;
+	};
+
+	ssb-rssd06-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd06>;
+	};
+
+	ssb-rssd07-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd07>;
+	};
+
+	ssb-rssd07-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd07>;
+	};
+
+	ssb-rssd08-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd08>;
+	};
+
+	ssb-rssd08-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd08>;
+	};
+
+	ssb-rssd09-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd09>;
+	};
+
+	ssb-rssd09-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd09>;
+	};
+
+	ssb-rssd10-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd10>;
+	};
+
+	ssb-rssd10-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd10>;
+	};
+
+	ssb-rssd11-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd11>;
+	};
+
+	ssb-rssd11-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd11>;
+	};
+
+	ssb-rssd12-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd12>;
+	};
+
+	ssb-rssd12-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd12>;
+	};
+
+	ssb-rssd13-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd13>;
+	};
+
+	ssb-rssd13-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd13>;
+	};
+
+	ssb-rssd14-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd14>;
+	};
+
+	ssb-rssd14-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd14>;
+	};
+
+	ssb-rssd15-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd15>;
+	};
+
+	ssb-rssd15-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd15>;
+	};
+
+	ssb-rssd16-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd16>;
+	};
+
+	ssb-rssd16-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd16>;
+	};
+
+	ssb-rssd17-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd17>;
+	};
+
+	ssb-rssd17-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd17>;
+	};
+
+	ssb-rssd18-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd18>;
+	};
+
+	ssb-rssd18-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd18>;
+	};
+
+	ssb-rssd19-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd19>;
+	};
+
+	ssb-rssd19-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd19>;
+	};
+
+	ssb-rssd20-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd20>;
+	};
+
+	ssb-rssd20-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd20>;
+	};
+
+	ssb-rssd21-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd21>;
+	};
+
+	ssb-rssd21-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd21>;
+	};
+
+	ssb-rssd22-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd22>;
+	};
+
+	ssb-rssd22-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd22>;
+	};
+
+	ssb-rssd23-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd23>;
+	};
+
+	ssb-rssd23-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd23>;
+	};
+
+	ssb-rssd24-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd24>;
+	};
+
+	ssb-rssd24-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd24>;
+	};
+
+	ssb-rssd25-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd25>;
+	};
+
+	ssb-rssd25-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd25>;
+	};
+
+	ssb-rssd26-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd26>;
+	};
+
+	ssb-rssd26-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd26>;
+	};
+
+	ssb-rssd27-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd27>;
+	};
+
+	ssb-rssd27-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd27>;
+	};
+
+	ssb-rssd28-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd28>;
+	};
+
+	ssb-rssd28-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd28>;
+	};
+
+	ssb-rssd29-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd29>;
+	};
+
+	ssb-rssd29-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd29>;
+	};
+
+	ssb-rssd30-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd30>;
+	};
+
+	ssb-rssd30-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd30>;
+	};
+
+	ssb-rssd31-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd31>;
+	};
+
+	ssb-rssd31-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd31>;
+	};
+
+	ssb-rssd32-sw0 {
+		compatible = "regulator-output";
+		vout-supply = <&sw0_ssb_rssd32>;
+	};
+
+	ssb-rssd32-sw1 {
+		compatible = "regulator-output";
+		vout-supply = <&sw1_ssb_rssd32>;
+	};
+
+	p3v3-nic-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&p3v3_nic>;
+	};
+
+	p1v8-nic-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&p1v8_nic>;
+	};
+
+	p1v2-nic-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&p1v2_nic>;
+	};
+
+	pvcore-nic1-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvcore_nic1>;
+	};
+
+	pvcore-nic2-consumer {
+		compatible = "regulator-output";
+		vout-supply = <&pvcore_nic2>;
+	};
+};
+
+&peci0 {
+	status = "okay";
+};
+
+&vuart1 {
+	status = "okay";
+};
+
+&lpc_snoop {
+	status = "okay";
+	snoop-ports = <0x80>, <0x81>;
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+#include "openbmc-flash-layout-64.dtsi"
+	};
+
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "alt-bmc";
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+#include "openbmc-flash-layout-64-alt.dtsi"
+	};
+};
+
+&uart1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd1_default
+			&pinctrl_rxd1_default
+			&pinctrl_nrts1_default
+			&pinctrl_ndtr1_default
+			&pinctrl_ndsr1_default
+			&pinctrl_ncts1_default
+			&pinctrl_ndcd1_default
+			&pinctrl_nri1_default>;
+};
+
+&uart5 {
+	status = "disabled";
+};
+
+&gpio1 {
+	status = "disabled";
+};
+
+&video {
+	status = "okay";
+};
+
+&vhub {
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_vgahs_default &pinctrl_vgavs_default>;
+};
+
+&mdio2 {
+	status = "okay";
+
+	ethphy2: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+		reset-gpios = <&gpio0 ASPEED_GPIO(V, 7) GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10000>;
+		reset-deassert-us = <300>;
+	};
+};
+
+&mdio3 {
+	status = "okay";
+
+	ethphy3: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+		reset-gpios = <&gpio0 ASPEED_GPIO(G, 2) GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10000>;
+		reset-deassert-us = <300>;
+	};
+};
+
+&mac2 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy2>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii3_default>;
+};
+
+&mac3 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy3>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii4_default>;
+};
+
+&adc0 {
+	status = "okay";
+	vref-supply = <&p1v8_bmc_aux>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default
+		     &pinctrl_adc1_default
+		     &pinctrl_adc2_default
+		     &pinctrl_adc3_default
+		     &pinctrl_adc4_default
+		     &pinctrl_adc5_default
+		     &pinctrl_adc6_default
+		     &pinctrl_adc7_default>;
+};
+
+&adc1 {
+	status = "okay";
+	vref-supply = <&p1v8_bmc_aux>;
+	aspeed,battery-sensing;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc8_default
+		     &pinctrl_adc9_default
+		     &pinctrl_adc10_default
+		     &pinctrl_adc11_default
+		     &pinctrl_adc12_default
+		     &pinctrl_adc13_default
+		     &pinctrl_adc15_default>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+};
+
+&gpio0 {
+	status = "okay";
+	gpio-line-names =
+	/* A0 - A7 */
+	"", "", "", "", "", "", "", "",
+	/* B0 - B7 */
+	"", "", "FM_ADR_TRIGGER_R_N", "RST_PLTRST_BUF_N", "BMC_TPM_RESET_N", "BMC_TPM_IRQ_N",
+	"PCH_TPM_RESET_N", "PCH_TPM_IRQ_N",
+	/* C0 - C7 */
+	"", "", "", "", "", "", "", "",
+	/* D0 - D7 */
+	"", "", "", "", "", "", "", "",
+	/* E0 - E7 */
+	"", "", "", "", "", "", "", "",
+	/* F0 - F7 */
+	"", "", "", "BMC_MUX_CPU1_RST_INT_N", "BMC_MUX_CPU2_RST_INT_N", "", "", "",
+	/* G0 - G7 */
+	"FM_SSD_CLK_DRVR1_EN", "FM_CK440Q_DEV_EN", "BMC_MAC1_RESET_N", "FM_DB2000_DEV_EN",
+	"FM_CPU_RMCA_LVT3_N", "FM_CPU_CATERR_LVT3_N", "FM_DBP_PRESENT_N", "",
+	/* H0 - H7 */
+	"SMB_SVC_PEX_RSSD17_32_INT", "LED_BMC_RDY", "RST_DBP_N", "", "", "", "", "",
+	/* I0 - I7 */
+	"JTAG_MUX_MODE_SEL", "JTAG_MUX_TRANS_ENBL", "JTAG_MUX_LSP_SEL5", "JTAG_MUX_MSTR_SEL",
+	"JTAG_MUX_LSP_SEL3", "", "JTAG_MUX_ENBL_N", "JTAG_MUX_RST_N",
+	/* J0 - J7 */
+	"", "", "", "", "", "", "", "",
+	/* K0 - K7 */
+	"", "", "", "", "", "", "", "",
+	/* L0 - L7 */
+	"", "", "", "", "RST_RTCRST_N", "RST_SRTCRST_N", "", "",
+	/* M0 - M7 */
+	"BMC_UART1_CTS_N", "BMC_UART1_DCD_N", "BMC_UART1_DSR_N", "BMC_UART1_RI_N",
+	"BMC_UART1_DTR_N", "BMC_UART1_RTS_N", "", "",
+	/* N0 - N7 */
+	"IRQ_BMC_PCH_NMI", "", "FM_PCH_BMC_THERMTRIP_N", "FM_BIOS_POST_CMPLT_N", "RST_PLTRST_N",
+	"FM_FLASH_SEC_OVRD", "FM_SMI_ACTIVE_N", "PWRGD_DBP",
+	/* O0 - O7 */
+	"CATERR_CPU2_EN", "H_LVT1_THERMTRIP_N", "CATERR_CPU3_EN", "SMB_SVC_PEX_CPU0_LED_INT",
+	"H_LVT1_MEMTRIP_N", "", "CATERR_CPU1_EN", "FM_PCH_ADR_COMPLETE_N",
+	/* P0 - P7 */
+	"PWRGD_SYS_PWROK", "PWRGD_PCH_PWROK", "BMC_MUX_CPU3_RST_INT_N", "BMC_MUX_SVC_RSSD_INT",
+	"FM_SLPS4_N", "IRQ_SML0_ALERT_N", "FM_SLPS3_N", "LED_BMC_HB",
+	/* Q0 - Q7 */
+	"", "PEX_BMC_RST", "PEX_VR_CTRL_RST", "PEX_NIC_RST", "PEX_CPU0_LED_RST", "PEX_CPU1_LED_RST",
+	"PEX_CPU2_LED_RST", "PEX_CPU3_LED_RST",
+	/* R0 - R7 */
+	"BMC_MUX_FANSSB_RSSD17_32_RST_INT_N", "BMC_MUX_FANPWM_RSSD01_16_RST_INT_N",
+	"BMC_MUX_SVC_VR_RST_INT_N", "BMC_MUX_NIC_RST_INT_N", "BMC_MUX_SVC_EXP_RST_INT_N",
+	"FM_CPU_ERR2_LVT3_N", "BMC_MUX_CPU0_RST_INT_N", "BMC_MUX_M2_RST_INT_N",
+	/* S0 - S7 */
+	"SMB_SVC_PEX_RSSD01_16_INT", "RST_PCH_RSMRST_R_N", "", "", "BMC_ROT_FPGA_RESET_N",
+	"FM_SSD_CLK_DRVR0_EN", "", "",
+	/* T0 - T7 */
+	"", "", "", "", "", "", "", "",
+	/* U0 - U7 */
+	"", "", "", "", "", "", "", "",
+	/* V0 - V7 */
+	"BMC_PEX_IRQ_INT", "RTC_BATT_TEST", "SMB_PEX_VR_CTRL_INT", "SMB_SVC_PEX_CPU3_LED_INT",
+	"PWRGD_CPUPWRGD", "SMB_SVC_PEX_CPU2_LED_INT", "SMB_SVC_PEX_CPU1_LED_INT",
+	"BMC_MAC0_RESET_N",
+	/* W0 - W7 */
+	"", "", "", "", "", "", "", "",
+	/* X0 - X7 */
+	"", "", "", "", "", "", "", "",
+	/* Y0 - Y7 */
+	"FM_THROTTLE_N", "FM_PASSWORD_CLEAR_N", "H_LVT3_CATERR_DLY_N", "FM_CPU_OL_INT_R_N", "", "",
+	"", "",
+	/* Z0 - Z7 */
+	"FM_CPU_ERR0_LVT3_N", "FM_CPU_ERR1_LVT3_N", "BMC_MUX_VR_PCH_CPU_RST_INT_N",
+	"JTAG_MUX_LSP_SEL1", "", "JTAG_MUX_LSP_SEL4", "JTAG_MUX_LSP_SEL2", "";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio0_unbiased_default>;
+};
+
+&pinctrl {
+	pinctrl_gpio0_unbiased_default: gpio_default {
+		pins = "AB15", "AD14", "R23", "A18", "AD24", "AD15", "AE14", "AC15", "U25", "AA24",
+		       "V24", "W26", "AA23", "V26", "U24", "V25", "AE15", "C15", "F15";
+		bias-disable;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+
+	bmc_mux_nic: mux@77 {
+		compatible = "maxim,max7357";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reset-gpios = <&gpio0 ASPEED_GPIO(R, 3) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+		vdd-supply = <&p3v3_aux>;
+
+		i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			smb_pex_nic: pinctrl@20 {
+				compatible = "cypress,cy8c9540";
+				reg = <0x20>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				interrupt-parent = <&smb_pex_vr_ctrl>;
+				interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+
+				vdd-supply = <&p3v3_aux>;
+				reset-gpios = <&gpio0 ASPEED_GPIO(Q, 3) GPIO_ACTIVE_HIGH>;
+
+				gpio-reserved-ranges = <19 1>, <22 6>, <30 6>, <38 2>;
+
+				gpio-line-names =
+				/* GPORT0 */
+				"IRQ_NIC2_OVT_WRNG", "FM_NIC2_ALLSTANDBY_N", "IRQ_NIC2_OVT_SHTDN",
+				"SMB_VR_PVCORE_NIC2_ALERT_N", "FM_NIC2_PERST1_N",
+				"SMB_NIC2_ALERT_N", "FM_NIC2_PERST3_N", "FM_NIC2_PERST2_N",
+				/* GPORT1 */
+				"FM_NIC1_RST_N", "FM_NIC1_PERST0_N", "FM_NIC1_PERST2_N",
+				"FM_NIC1_PERST3_N", "SMB_NIC1_ALERT_N", "FM_NIC1_PERST1_N",
+				"SMB_VR_PVCORE_NIC1_ALERT_N", "IRQ_NIC1_OVT_SHTDN",
+				/* GPORT2 */
+				"SMB_VR_P3V3_NIC_ALERT_N", "FM_NIC2_FLASH_PRSNT",
+				"FM_NIC1_FLASH_PRSNT", "",
+				/* GPORT3 */
+				"FM_NIC2_PERST0_N", "FM_NIC2_RST_N", "", "", "", "", "", "",
+				/* GPORT4 */
+				"FM_NIC1_ALLSTANDBY_N", "IRQ_NIC1_OVT_WRNG", "", "", "", "", "", "",
+				/* GPORT5 */
+				"SMB_VR_P1V8_NIC_ALERT_N", "SMB_VR_P1V2_NIC_ALERT_N", "", "";
+
+				pinctrl-0 = <&U62160_pins>;
+				pinctrl-names = "default";
+				U62160_pins: cfg-pins {
+					pins = "gp03", "gp16", "gp20", "gp50", "gp51";
+					function = "gpio";
+					input-enable;
+					bias-pull-up;
+				};
+			};
+		};
+
+		i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			pvcore_nic2: ir38263-pvcore-nic2@40 {
+				compatible = "infineon,ir38263";
+				reg = <0x40>;
+
+				regulator-name = "pvcore_nic2";
+				regulator-enable-ramp-delay = <2000>;
+				vin-supply = <&p12v>;
+			};
+		};
+
+		i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			pvcore_nic1: ir38263-pvcore-nic1@40 {
+				compatible = "infineon,ir38263";
+				reg = <0x40>;
+
+				regulator-name = "pvcore_nic1";
+				regulator-enable-ramp-delay = <2000>;
+				vin-supply = <&p12v>;
+			};
+		};
+
+		i2c@4 {
+			reg = <4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c@5 {
+			reg = <5>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			p3v3_nic: ir38263-p3v3-nic@40 {
+				compatible = "infineon,ir38263";
+				reg = <0x40>;
+
+				regulator-name = "p3v3_nic";
+				regulator-enable-ramp-delay = <2000>;
+				vin-supply = <&p12v>;
+			};
+		};
+
+		i2c@6 {
+			reg = <6>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			p1v2_nic: ir38263-p1v2-nic@40 {
+				compatible = "infineon,ir38263";
+				reg = <0x40>;
+
+				regulator-name = "p1v2_nic";
+				regulator-enable-ramp-delay = <2000>;
+				vin-supply = <&p12v>;
+			};
+		};
+
+		i2c@7 {
+			reg = <7>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			p1v8_nic: ir38263-p1v8-nic@40 {
+				compatible = "infineon,ir38263";
+				reg = <0x40>;
+
+				regulator-name = "p1v8_nic";
+				regulator-enable-ramp-delay = <2000>;
+				vin-supply = <&p12v>;
+			};
+		};
+	};
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+
+	i2cmux1: mux@77 {
+		compatible = "maxim,max7357";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reset-gpios = <&gpio0 ASPEED_GPIO(R, 7) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+		vdd-supply = <&p3v3_aux>;
+
+		i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			smb_m2_ssb_ssd1: regulator@3a {
+				compatible = "maxim,max5978";
+				reg = <0x3a>;
+				vss1-supply = <&p3v3_aux>;
+
+				interrupt-parent = <&smb_pex_vr_ctrl>;
+				interrupts = <30 IRQ_TYPE_LEVEL_LOW>;
+				leds {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					led@0 {
+						reg = <0>;
+						label = "m2_ssb_ssd1:green:power";
+						default-state = "off";
+					};
+				};
+
+				regulators {
+					sw0_smb_m2_ssb_ssd1: sw0 {
+						shunt-resistor-micro-ohms = <12000>;
+						regulator-over-current-protection;
+						regulator-oc-protection-microamp = <2800000>;
+						regulator-name = "p3v3_m2_ssd1";
+						regulator-enable-ramp-delay = <10000>;
+					};
+				};
+			};
+		};
+
+		i2c@4 {
+			reg = <4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c@5 {
+			reg = <5>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			smb_m2_ssb_ssd2: regulator@3a {
+				compatible = "maxim,max5978";
+				reg = <0x3a>;
+
+				interrupt-parent = <&smb_pex_vr_ctrl>;
+				interrupts = <39 IRQ_TYPE_LEVEL_LOW>;
+				vss1-supply = <&p3v3_aux>;
+				leds {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					led@0 {
+						reg = <0>;
+						label = "m2_ssb_ssd2:green:power";
+						default-state = "off";
+					};
+				};
+
+				regulators {
+					sw0_smb_m2_ssb_ssd2: sw0 {
+						shunt-resistor-micro-ohms = <12000>;
+						regulator-over-current-protection;
+						regulator-oc-protection-microamp = <2800000>;
+						regulator-name = "p3v3_m2_ssd2";
+						regulator-enable-ramp-delay = <10000>;
+					};
+				};
+			};
+		};
+
+		i2c@6 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c@7 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&i2c4 {
+	status = "okay";
+	multi-master;
+	bus-frequency = <1000000>;
+
+	bmc-slave@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+
+		i2c-protocol;
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	i2cmux2: mux@77 {
+		compatible = "maxim,max7357";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reset-gpios = <&gpio0 ASPEED_GPIO(Z, 2) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+		vdd-supply = <&p3v3_aux>;
+
+		i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			p1v05_pch_aux: ir38263-p1v05-pch-aux@40 {
+				compatible = "infineon,ir38263";
+				reg = <0x40>;
+
+				regulator-name = "p1v05_pch_aux";
+				regulator-enable-ramp-delay = <2000>;
+				vin-supply = <&p12v>;
+			};
+		};
+
+		i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			p1v8_pch_aux: ir38060-p1v8-pch-aux@40 {
+				compatible = "infineon,ir38060";
+				reg = <0x40>;
+
+				regulator-name = "p1v8_pch_aux";
+				regulator-enable-ramp-delay = <2000>;
+				vin-supply = <&p12v>;
+			};
+		};
+
+		i2c@4 {
+			reg = <4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c@5 {
+			reg = <5>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c@6 {
+			reg = <6>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c@7 {
+			reg = <7>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&i2c14 {
+	status = "okay";
+
+	i2cmux13: mux@77 {
+		compatible = "maxim,max7357";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reset-gpios = <&gpio0 ASPEED_GPIO(R, 6) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+		vdd-supply = <&p3v3_aux>;
+
+		i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			smb_pex_cpu0_event: pinctrl@20 {
+				compatible = "cypress,cy8c9540";
+				reg = <0x20>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				interrupt-parent = <&smb_pex_vr_ctrl>;
+				interrupts = <10 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+
+				vdd-supply = <&p3v3_aux>;
+				reset-gpios = <&smb_svc_pex_cpu0_led 16 GPIO_ACTIVE_HIGH>;
+
+				gpio-reserved-ranges = <14 2>, <21 1>, <25 3>, <33 1>;
+
+				gpio-line-names =
+				/* GPORT0 */
+				"PWRGD_CHD_CPU0", "PWRGD_CHC_CPU0",
+				"PWRGD_CHB_CPU0", "PWRGD_CHA_CPU0",
+				"PWRGD_CHE_CPU0", "PWRGD_CHF_CPU0",
+				"PWRGD_CHG_CPU0", "PWRGD_CHH_CPU0",
+				/* GPORT1 */
+				"SMB_VR_PVPP_HBM_CPU0_ALERT_N", "SMB_VR_PVCCINFAON_CPU0_ALERT_N",
+				"SMB_VR_PVNN_MAIN_CPU0_ALERT_N", "SMB_VR_PVCCD_HV_CPU0_ALERT_N",
+				"SMB_VR_PVCCIN_CPU0_ALERT_N", "SEL_SMB_DIMM_CPU0",
+				"", "",
+				/* GPORT2 */
+				"PWRGD_LVC3_CPU0_AB_DRAM_G", "PWRGD_LVC3_CPU0_CD_DRAM_G",
+				"PWRGD_LVC3_CPU0_EF_DRAM_G", "PWRGD_LVC3_CPU0_GH_DRAM_G",
+				/* GPORT3 */
+				"FM_CPU0_DISABLE_COD_N", "",
+				"RST_LVC3_CPU0_RESET_N", "PWRGD_LVC3_CPU0_PWRGOOD",
+				"PWRGD_PLT_AUX_CPU0_LVT3", "",
+				"", "",
+				/* GPORT4 */
+				"H_LVT3_CPU0_PROCHOT_N", "H_LVT3_CPU0_MEMHOT_IN_N",
+				"H_LVT3_CPU0_MEMHOT_OUT_N", "H_LVT3_CPU0_MEMTRIP_OUT_N",
+				"H_LVT3_CPU0_THERMTRIP_OUT_N", "",
+				"H_LVT3_CPU0_NMI", "FM_S3M_CPU0_CD_INIT_ERROR",
+				/* GPORT5 */
+				"FM_CPU0_PKG_ID0", "FM_CPU0_PKG_ID1",
+				"FM_CPU0_PROC_ID0", "FM_CPU0_PROC_ID1";
+
+				pinctrl-0 = <&U62080_pins>;
+				pinctrl-names = "default";
+				U62080_pins: cfg-pins {
+					pins = "gp10", "gp11", "gp12", "gp13", "gp14";
+					function = "gpio";
+					input-enable;
+					bias-pull-up;
+				};
+			};
+		};
+
+		i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			pvccinfaon-pvccfa-cpu0@58 {
+				compatible = "mps,mp2971";
+				reg = <0x58>;
+				interrupt-parent = <&smb_pex_cpu0_event>;
+				interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+
+				regulators {
+					pvccinfaon_cpu0: vout0 {
+						regulator-name = "pvccinfaon_cpu0";
+						regulator-enable-ramp-delay = <200>;
+					};
+					pvccfa_ehv_cpu0: vout1 {
+						regulator-name = "pvccfa_ehv_cpu0";
+						regulator-enable-ramp-delay = <200>;
+					};
+				};
+			};
+			tda38640-pvnn-main-cpu0@40 {
+				compatible = "infineon,tda38640";
+				reg = <0x40>;
+				interrupt-parent = <&smb_pex_cpu0_event>;
+				interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
+
+				regulators {
+					pvnn_main_cpu0: vout {
+						regulator-name = "pvnn_main_cpu0";
+						regulator-enable-ramp-delay = <200>;
+					};
+				};
+			};
+		};
+
+		i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			mp2973-pvccin-pvccfa-cpu0@58 {
+				compatible = "mps,mp2973";
+				reg = <0x58>;
+				interrupt-parent = <&smb_pex_cpu0_event>;
+				interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+
+				regulators {
+					pvccin_cpu0: vout0 {
+						regulator-name = "pvccin_cpu0";
+						regulator-enable-ramp-delay = <200>;
+					};
+					pvccfa_ehv_fivra_cpu0: vout1 {
+						regulator-name = "pvccfa_ehv_fivra_cpu0";
+						regulator-enable-ramp-delay = <200>;
+					};
+				};
+			};
+		};
+
+		i2c@4 {
+			reg = <4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			tda38640-pvccd-hv-cpu0@40 {
+				compatible = "infineon,tda38640";
+				reg = <0x40>;
+				interrupt-parent = <&smb_pex_cpu0_event>;
+				interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+				infineon,en-pin-fixed-level;
+
+				regulators {
+					pvccd_hv_cpu0: vout {
+						regulator-name = "pvccd_hv_cpu0";
+						regulator-enable-ramp-delay = <200>;
+					};
+				};
+			};
+		};
+
+		i2c@5 {
+			reg = <5>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			tda38640-pvpp-hbm-cpu0@40 {
+				compatible = "infineon,tda38640";
+				reg = <0x40>;
+				interrupt-parent = <&smb_pex_cpu0_event>;
+				interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+
+				regulators {
+					pvpp_hbm_cpu0: vout {
+						regulator-name = "pvpp_hbm_cpu0";
+						regulator-enable-ramp-delay = <200>;
+					};
+				};
+			};
+		};
+
+		i2c@6 {
+			reg = <6>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c@7 {
+			reg = <7>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&i2c7 {
+	status = "okay";
+
+	i2cmux4: mux@77 {
+		compatible = "maxim,max7357";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reset-gpios = <&gpio0 ASPEED_GPIO(F, 3) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+		vdd-supply = <&p3v3_aux>;
+
+		i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			smb_pex_cpu1_event: pinctrl@20 {
+				compatible = "cypress,cy8c9540";
+				reg = <0x20>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				interrupt-parent = <&smb_pex_vr_ctrl>;
+				interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+
+				vdd-supply = <&p3v3_aux>;
+				reset-gpios = <&smb_svc_pex_cpu1_led 16 GPIO_ACTIVE_HIGH>;
+
+				gpio-reserved-ranges = <14 2>, <21 1>, <25 3>, <33 1>;
+
+				gpio-line-names =
+				/* GPORT0 */
+				"PWRGD_CHD_CPU1", "PWRGD_CHC_CPU1",
+				"PWRGD_CHB_CPU1", "PWRGD_CHA_CPU1",
+				"PWRGD_CHE_CPU1", "PWRGD_CHF_CPU1",
+				"PWRGD_CHG_CPU1", "PWRGD_CHH_CPU1",
+				/* GPORT1 */
+				"SMB_VR_PVPP_HBM_CPU1_ALERT_N", "SMB_VR_PVCCINFAON_CPU1_ALERT_N",
+				"SMB_VR_PVNN_MAIN_CPU1_ALERT_N", "SMB_VR_PVCCD_HV_CPU1_ALERT_N",
+				"SMB_VR_PVCCIN_CPU1_ALERT_N", "SEL_SMB_DIMM_CPU1",
+				"", "",
+				/* GPORT2 */
+				"PWRGD_LVC3_CPU1_AB_DRAM_G", "PWRGD_LVC3_CPU1_CD_DRAM_G",
+				"PWRGD_LVC3_CPU1_EF_DRAM_G", "PWRGD_LVC3_CPU1_GH_DRAM_G",
+				/* GPORT3 */
+				"FM_CPU1_DISABLE_COD_N", "",
+				"RST_LVC3_CPU1_RESET_N", "PWRGD_LVC3_CPU1_PWRGOOD",
+				"PWRGD_PLT_AUX_CPU1_LVT3", "",
+				"", "",
+				/* GPORT4 */
+				"H_LVT3_CPU1_PROCHOT_N", "H_LVT3_CPU1_MEMHOT_IN_N",
+				"H_LVT3_CPU1_MEMHOT_OUT_N", "H_LVT3_CPU1_MEMTRIP_OUT_N",
+				"H_LVT3_CPU1_THERMTRIP_OUT_N", "",
+				"H_LVT3_CPU1_NMI", "FM_S3M_CPU1_CD_INIT_ERROR",
+				/* GPORT5 */
+				"FM_CPU1_PKG_ID0", "FM_CPU1_PKG_ID1",
+				"FM_CPU1_PROC_ID0", "FM_CPU1_PROC_ID1";
+
+				pinctrl-0 = <&U62090_pins>;
+				pinctrl-names = "default";
+				U62090_pins: cfg-pins {
+					pins = "gp10", "gp11", "gp12", "gp13", "gp14";
+					function = "gpio";
+					input-enable;
+					bias-pull-up;
+				};
+			};
+		};
+
+		i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			pvccinfaon-pvccfa-cpu1@58 {
+				compatible = "mps,mp2971";
+				reg = <0x58>;
+				interrupt-parent = <&smb_pex_cpu1_event>;
+				interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+
+				regulators {
+					pvccinfaon_cpu1: vout0 {
+						regulator-name = "pvccinfaon_cpu1";
+						regulator-enable-ramp-delay = <200>;
+					};
+					pvccfa_ehv_cpu1: vout1 {
+						regulator-name = "pvccfa_ehv_cpu1";
+						regulator-enable-ramp-delay = <200>;
+					};
+				};
+			};
+			tda38640-pvnn-main-cpu1@40 {
+				compatible = "infineon,tda38640";
+				reg = <0x40>;
+				interrupt-parent = <&smb_pex_cpu1_event>;
+				interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
+
+				regulators {
+					pvnn_main_cpu1: vout {
+						regulator-name = "pvnn_main_cpu1";
+						regulator-enable-ramp-delay = <200>;
+					};
+				};
+			};
+		};
+
+		i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			mp2973-pvccin-pvccfa-cpu1@58 {
+				compatible = "mps,mp2973";
+				reg = <0x58>;
+				interrupt-parent = <&smb_pex_cpu1_event>;
+				interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+
+				regulators {
+					pvccin_cpu1: vout0 {
+						regulator-name = "pvccin_cpu1";
+						regulator-enable-ramp-delay = <200>;
+					};
+					pvccfa_ehv_fivra_cpu1: vout1 {
+						regulator-name = "pvccfa_ehv_fivra_cpu1";
+						regulator-enable-ramp-delay = <200>;
+					};
+				};
+			};
+		};
+
+		i2c@4 {
+			reg = <4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			tda38640-pvccd-hv-cpu1@40 {
+				compatible = "infineon,tda38640";
+				reg = <0x40>;
+				interrupt-parent = <&smb_pex_cpu1_event>;
+				interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+				infineon,en-pin-fixed-level;
+
+				regulators {
+					pvccd_hv_cpu1: vout {
+						regulator-name = "pvccd_hv_cpu1";
+						regulator-enable-ramp-delay = <200>;
+					};
+				};
+			};
+		};
+
+		i2c@5 {
+			reg = <5>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			tda38640-pvpp-hbm-cpu1@40 {
+				compatible = "infineon,tda38640";
+				reg = <0x40>;
+				interrupt-parent = <&smb_pex_cpu1_event>;
+				interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+
+				regulators {
+					pvpp_hbm_cpu1: vout {
+						regulator-name = "pvpp_hbm_cpu1";
+						regulator-enable-ramp-delay = <200>;
+					};
+				};
+			};
+		};
+
+		i2c@6 {
+			reg = <6>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c@7 {
+			reg = <7>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&i2c6 {
+	status = "okay";
+
+	i2cmux3: mux@77 {
+		compatible = "maxim,max7357";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		vdd-supply = <&p3v3_aux>;
+
+		i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			smb_pex_cpu2_event: pinctrl@20 {
+				compatible = "cypress,cy8c9540";
+				reg = <0x20>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				interrupt-parent = <&smb_pex_vr_ctrl>;
+				interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+
+				vdd-supply = <&p3v3_aux>;
+				reset-gpios = <&smb_svc_pex_cpu2_led 16 GPIO_ACTIVE_HIGH>;
+
+				gpio-reserved-ranges = <14 2>, <21 1>, <25 3>, <33 1>;
+
+				gpio-line-names =
+				/* GPORT0 */
+				"PWRGD_CHD_CPU2", "PWRGD_CHC_CPU2",
+				"PWRGD_CHB_CPU2", "PWRGD_CHA_CPU2",
+				"PWRGD_CHE_CPU2", "PWRGD_CHF_CPU2",
+				"PWRGD_CHG_CPU2", "PWRGD_CHH_CPU2",
+				/* GPORT1 */
+				"SMB_VR_PVPP_HBM_CPU2_ALERT_N", "SMB_VR_PVCCINFAON_CPU2_ALERT_N",
+				"SMB_VR_PVNN_MAIN_CPU2_ALERT_N", "SMB_VR_PVCCD_HV_CPU2_ALERT_N",
+				"SMB_VR_PVCCIN_CPU2_ALERT_N", "SEL_SMB_DIMM_CPU2",
+				"", "",
+				/* GPORT2 */
+				"PWRGD_LVC3_CPU2_AB_DRAM_G", "PWRGD_LVC3_CPU2_CD_DRAM_G",
+				"PWRGD_LVC3_CPU2_EF_DRAM_G", "PWRGD_LVC3_CPU2_GH_DRAM_G",
+				/* GPORT3 */
+				"FM_CPU2_DISABLE_COD_N", "",
+				"RST_LVC3_CPU2_RESET_N", "PWRGD_LVC3_CPU2_PWRGOOD",
+				"PWRGD_PLT_AUX_CPU2_LVT3", "",
+				"", "",
+				/* GPORT4 */
+				"H_LVT3_CPU2_PROCHOT_N", "H_LVT3_CPU2_MEMHOT_IN_N",
+				"H_LVT3_CPU2_MEMHOT_OUT_N", "H_LVT3_CPU2_MEMTRIP_OUT_N",
+				"H_LVT3_CPU2_THERMTRIP_OUT_N", "",
+				"H_LVT3_CPU2_NMI", "FM_S3M_CPU2_CD_INIT_ERROR",
+				/* GPORT5 */
+				"FM_CPU2_PKG_ID0", "FM_CPU2_PKG_ID1",
+				"FM_CPU2_PROC_ID0", "FM_CPU2_PROC_ID1";
+
+				pinctrl-0 = <&U62100_pins>;
+				pinctrl-names = "default";
+				U62100_pins: cfg-pins {
+					pins = "gp10", "gp11", "gp12", "gp13", "gp14";
+					function = "gpio";
+					input-enable;
+					bias-pull-up;
+				};
+			};
+		};
+
+		i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			pvccinfaon-pvccfa-cpu2@58 {
+				compatible = "mps,mp2971";
+				reg = <0x58>;
+				interrupt-parent = <&smb_pex_cpu2_event>;
+				interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+
+				regulators {
+					pvccinfaon_cpu2: vout0 {
+						regulator-name = "pvccinfaon_cpu2";
+						regulator-enable-ramp-delay = <200>;
+					};
+					pvccfa_ehv_cpu2: vout1 {
+						regulator-name = "pvccfa_ehv_cpu2";
+						regulator-enable-ramp-delay = <200>;
+					};
+				};
+			};
+			tda38640-pvnn-main-cpu2@40 {
+				compatible = "infineon,tda38640";
+				reg = <0x40>;
+				interrupt-parent = <&smb_pex_cpu2_event>;
+				interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
+
+				regulators {
+					pvnn_main_cpu2: vout {
+						regulator-name = "pvnn_main_cpu2";
+						regulator-enable-ramp-delay = <200>;
+					};
+				};
+			};
+		};
+
+		i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			mp2973-pvccin-pvccfa-cpu2@58 {
+				compatible = "mps,mp2973";
+				reg = <0x58>;
+				interrupt-parent = <&smb_pex_cpu2_event>;
+				interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+
+				regulators {
+					pvccin_cpu2: vout0 {
+						regulator-name = "pvccin_cpu2";
+						regulator-enable-ramp-delay = <200>;
+					};
+					pvccfa_ehv_fivra_cpu2: vout1 {
+						regulator-name = "pvccfa_ehv_fivra_cpu2";
+						regulator-enable-ramp-delay = <200>;
+					};
+				};
+			};
+		};
+
+		i2c@4 {
+			reg = <4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			tda38640-pvccd-hv-cpu2@40 {
+				compatible = "infineon,tda38640";
+				reg = <0x40>;
+				interrupt-parent = <&smb_pex_cpu2_event>;
+				interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+				infineon,en-pin-fixed-level;
+
+				regulators {
+					pvccd_hv_cpu2: vout {
+						regulator-name = "pvccd_hv_cpu2";
+						regulator-enable-ramp-delay = <200>;
+					};
+				};
+			};
+		};
+
+		i2c@5 {
+			reg = <5>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			tda38640-pvpp-hbm-cpu2@40 {
+				compatible = "infineon,tda38640";
+				reg = <0x40>;
+				interrupt-parent = <&smb_pex_cpu2_event>;
+				interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+
+				regulators {
+					pvpp_hbm_cpu2: vout {
+						regulator-name = "pvpp_hbm_cpu2";
+						regulator-enable-ramp-delay = <200>;
+					};
+				};
+			};
+		};
+
+		i2c@6 {
+			reg = <6>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c@7 {
+			reg = <7>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&i2c12 {
+	status = "okay";
+
+	i2cmux22: mux@77 {
+		compatible = "maxim,max7357";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reset-gpios = <&gpio0 ASPEED_GPIO(P, 2) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+		vdd-supply = <&p3v3_aux>;
+
+		i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			smb_pex_cpu3_event: pinctrl@20 {
+				compatible = "cypress,cy8c9540";
+				reg = <0x20>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				interrupt-parent = <&smb_pex_vr_ctrl>;
+				interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+
+				vdd-supply = <&p3v3_aux>;
+				reset-gpios = <&smb_svc_pex_cpu3_led 16 GPIO_ACTIVE_HIGH>;
+
+				gpio-reserved-ranges = <14 2>, <21 1>, <25 3>, <33 1>;
+
+				gpio-line-names =
+				/* GPORT0 */
+				"PWRGD_CHD_CPU3", "PWRGD_CHC_CPU3",
+				"PWRGD_CHB_CPU3", "PWRGD_CHA_CPU3",
+				"PWRGD_CHE_CPU3", "PWRGD_CHF_CPU3",
+				"PWRGD_CHG_CPU3", "PWRGD_CHH_CPU3",
+				/* GPORT1 */
+				"SMB_VR_PVPP_HBM_CPU3_ALERT_N", "SMB_VR_PVCCINFAON_CPU3_ALERT_N",
+				"SMB_VR_PVNN_MAIN_CPU3_ALERT_N", "SMB_VR_PVCCD_HV_CPU3_ALERT_N",
+				"SMB_VR_PVCCIN_CPU3_ALERT_N", "SEL_SMB_DIMM_CPU3",
+				"", "",
+				/* GPORT2 */
+				"PWRGD_LVC3_CPU3_AB_DRAM_G", "PWRGD_LVC3_CPU3_CD_DRAM_G",
+				"PWRGD_LVC3_CPU3_EF_DRAM_G", "PWRGD_LVC3_CPU3_GH_DRAM_G",
+				/* GPORT3 */
+				"FM_CPU3_DISABLE_COD_N", "",
+				"RST_LVC3_CPU3_RESET_N", "PWRGD_LVC3_CPU3_PWRGOOD",
+				"PWRGD_PLT_AUX_CPU3_LVT3", "",
+				"", "",
+				/* GPORT4 */
+				"H_LVT3_CPU3_PROCHOT_N", "H_LVT3_CPU3_MEMHOT_IN_N",
+				"H_LVT3_CPU3_MEMHOT_OUT_N", "H_LVT3_CPU3_MEMTRIP_OUT_N",
+				"H_LVT3_CPU3_THERMTRIP_OUT_N", "",
+				"H_LVT3_CPU3_NMI", "FM_S3M_CPU3_CD_INIT_ERROR",
+				/* GPORT5 */
+				"FM_CPU3_PKG_ID0", "FM_CPU3_PKG_ID1",
+				"FM_CPU3_PROC_ID0", "FM_CPU3_PROC_ID1";
+
+				pinctrl-0 = <&U62110_pins>;
+				pinctrl-names = "default";
+				U62110_pins: cfg-pins {
+					pins = "gp10", "gp11", "gp12", "gp13", "gp14";
+					function = "gpio";
+					input-enable;
+					bias-pull-up;
+				};
+			};
+		};
+
+		i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			pvccinfaon-pvccfa-cpu3@58 {
+				compatible = "mps,mp2971";
+				reg = <0x58>;
+				interrupt-parent = <&smb_pex_cpu3_event>;
+				interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+
+				regulators {
+					pvccinfaon_cpu3: vout0 {
+						regulator-name = "pvccinfaon_cpu3";
+						regulator-enable-ramp-delay = <200>;
+					};
+					pvccfa_ehv_cpu3: vout1 {
+						regulator-name = "pvccfa_ehv_cpu3";
+						regulator-enable-ramp-delay = <200>;
+					};
+				};
+			};
+			tda38640-pvnn-main-cpu3@40 {
+				compatible = "infineon,tda38640";
+				reg = <0x40>;
+				interrupt-parent = <&smb_pex_cpu3_event>;
+				interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
+
+				regulators {
+					pvnn_main_cpu3: vout {
+						regulator-name = "pvnn_main_cpu3";
+						regulator-enable-ramp-delay = <200>;
+					};
+				};
+			};
+		};
+
+		i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			mp2973-pvccin-pvccfa-cpu3@58 {
+				compatible = "mps,mp2973";
+				reg = <0x58>;
+				interrupt-parent = <&smb_pex_cpu3_event>;
+				interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+
+				regulators {
+					pvccin_cpu3: vout0 {
+						regulator-name = "pvccin_cpu3";
+						regulator-enable-ramp-delay = <200>;
+					};
+					pvccfa_ehv_fivra_cpu3: vout1 {
+						regulator-name = "pvccfa_ehv_fivra_cpu3";
+						regulator-enable-ramp-delay = <200>;
+					};
+				};
+			};
+		};
+
+		i2c@4 {
+			reg = <4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			tda38640-pvccd-hv-cpu3@40 {
+				compatible = "infineon,tda38640";
+				reg = <0x40>;
+				interrupt-parent = <&smb_pex_cpu3_event>;
+				interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+				infineon,en-pin-fixed-level;
+
+				regulators {
+					pvccd_hv_cpu3: vout {
+						regulator-name = "pvccd_hv_cpu3";
+						regulator-enable-ramp-delay = <200>;
+					};
+				};
+			};
+		};
+
+		i2c@5 {
+			reg = <5>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			tda38640-pvpp-hbm-cpu3@40 {
+				compatible = "infineon,tda38640";
+				reg = <0x40>;
+				interrupt-parent = <&smb_pex_cpu3_event>;
+				interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+
+				regulators {
+					pvpp_hbm_cpu3: vout {
+						regulator-name = "pvpp_hbm_cpu3";
+						regulator-enable-ramp-delay = <200>;
+					};
+				};
+			};
+		};
+
+		i2c@6 {
+			reg = <6>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c@7 {
+			reg = <7>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&i2c15 {
+	status = "okay";
+
+	i2cmux14: mux@77 {
+		compatible = "maxim,max7357";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reset-gpios = <&gpio0 ASPEED_GPIO(R, 1) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+		vdd-supply = <&p3v3_aux>;
+
+		i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			i2cmux15: mux@70 {
+				compatible = "maxim,max7357";
+				reg = <0x70>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				reset-gpios = <&bmc_pex_irq 11 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+				vdd-supply = <&p3v3_aux>;
+			};
+		};
+
+		i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			i2cmux16: mux@70 {
+				compatible = "maxim,max7357";
+				reg = <0x70>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				reset-gpios = <&bmc_pex_irq 2 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+				vdd-supply = <&p3v3_aux>;
+			};
+		};
+
+		i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			i2cmux17: mux@70 {
+				compatible = "maxim,max7357";
+				reg = <0x70>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				reset-gpios = <&bmc_pex_irq 0 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+				vdd-supply = <&p3v3_aux>;
+			};
+		};
+
+		i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			i2cmux18: mux@70 {
+				compatible = "maxim,max7357";
+				reg = <0x70>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				reset-gpios = <&bmc_pex_irq 3 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+				vdd-supply = <&p3v3_aux>;
+			};
+		};
+
+		i2c@4 {
+			reg = <4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			i2cmux19: mux@70 {
+				compatible = "maxim,max7357";
+				reg = <0x70>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				reset-gpios = <&bmc_pex_irq 9 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+				vdd-supply = <&p3v3_aux>;
+			};
+		};
+
+		i2c@5 {
+			reg = <5>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			smb_pex_rssd17_32: pinctrl@20 {
+				compatible = "cypress,cy8c9560";
+				reg = <0x20>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				interrupt-parent = <&bmc_pex_irq>;
+				interrupts = <13 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+
+				vdd-supply = <&p3v3_aux>;
+				reset-gpios = <&bmc_pex_irq 19 GPIO_ACTIVE_HIGH>;
+
+				gpio-reserved-ranges = <48 12>;
+
+				gpio-line-names =
+				/* GPORT0 */
+				"RSSD17_SMBRST_N", "RSSD18_SMBRST_N",
+				"RSSD19_SMBRST_N", "RSSD20_SMBRST_N",
+				"RSSD21_SMBRST_N", "RSSD22_SMBRST_N",
+				"RSSD23_SMBRST_N", "RSSD24_SMBRST_N",
+				/* GPORT1 */
+				"RSSD25_SMBRST_N", "RSSD26_SMBRST_N",
+				"RSSD27_SMBRST_N", "RSSD28_SMBRST_N",
+				"RSSD29_SMBRST_N", "RSSD30_SMBRST_N",
+				"RSSD31_SMBRST_N", "RSSD32_SMBRST_N",
+				/* GPORT2 */
+				"RSSD17_PWRDIS", "RSSD18_PWRDIS",
+				"RSSD19_PWRDIS", "RSSD20_PWRDIS",
+				/* GPORT3 */
+				"RSSD21_PWRDIS", "RSSD22_PWRDIS",
+				"RSSD23_PWRDIS", "RSSD24_PWRDIS",
+				"RSSD25_PWRDIS", "RSSD26_PWRDIS",
+				"RSSD27_PWRDIS", "RSSD28_PWRDIS",
+				/* GPORT4 */
+				"RSSD29_PWRDIS", "RSSD30_PWRDIS",
+				"RSSD31_PWRDIS", "RSSD32_PWRDIS",
+				"RSSD17_RESET_N", "RSSD18_RESET_N",
+				"RSSD19_RESET_N", "RSSD20_RESET_N",
+				/* GPORT5 */
+				"RSSD21_RESET_N", "RSSD22_RESET_N",
+				"RSSD23_RESET_N", "RSSD24_RESET_N",
+				"RSSD25_RESET_N", "RSSD26_RESET_N",
+				"RSSD27_RESET_N", "RSSD28_RESET_N",
+				/* GPORT6 */
+				"RSSD29_RESET_N", "RSSD30_RESET_N",
+				"RSSD31_RESET_N", "RSSD32_RESET_N",
+				"", "",
+				"", "",
+				/* GPORT7 */
+				"", "",
+				"", "",
+				"", "",
+				"", "";
+			};
+		};
+
+		i2c@6 {
+			reg = <6>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			i2cmux20: mux@70 {
+				compatible = "maxim,max7357";
+				reg = <0x70>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				reset-gpios = <&bmc_pex_irq 4 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+				vdd-supply = <&p3v3_aux>;
+
+				i2c@0 {
+					reg = <0>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@1 {
+					reg = <1>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@2 {
+					reg = <2>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@3 {
+					reg = <3>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@4 {
+					reg = <4>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@5 {
+					reg = <5>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@6 {
+					reg = <6>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@7 {
+					reg = <7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+			};
+		};
+
+		i2c@7 {
+			reg = <7>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			i2cmux21: mux@70 {
+				compatible = "maxim,max7357";
+				reg = <0x70>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				reset-gpios = <&bmc_pex_irq 5 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+				vdd-supply = <&p3v3_aux>;
+
+				i2c@0 {
+					reg = <0>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@1 {
+					reg = <1>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@2 {
+					reg = <2>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@3 {
+					reg = <3>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@4 {
+					reg = <4>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@5 {
+					reg = <5>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@6 {
+					reg = <6>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@7 {
+					reg = <7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+			};
+		};
+	};
+};
+
+&i2c8 {
+	status = "okay";
+
+	i2cmux5: mux@77 {
+		compatible = "maxim,max7357";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reset-gpios = <&gpio0 ASPEED_GPIO(R, 0) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+		vdd-supply = <&p3v3_aux>;
+
+		i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			i2cmux6: mux@70 {
+				compatible = "maxim,max7357";
+				reg = <0x70>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				reset-gpios = <&bmc_pex_irq 16 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+				vdd-supply = <&p3v3_aux>;
+			};
+		};
+
+		i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			i2cmux7: mux@70 {
+				compatible = "maxim,max7357";
+				reg = <0x70>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				reset-gpios = <&bmc_pex_irq 7 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+				vdd-supply = <&p3v3_aux>;
+			};
+		};
+
+		i2c@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			i2cmux8: mux@70 {
+				compatible = "maxim,max7357";
+				reg = <0x70>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				reset-gpios = <&bmc_pex_irq 1 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+				vdd-supply = <&p3v3_aux>;
+			};
+		};
+
+		i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			i2cmux9: mux@70 {
+				compatible = "maxim,max7357";
+				reg = <0x70>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				reset-gpios = <&bmc_pex_irq 10 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+				vdd-supply = <&p3v3_aux>;
+			};
+		};
+
+		i2c@4 {
+			reg = <4>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			i2cmux10: mux@70 {
+				compatible = "maxim,max7357";
+				reg = <0x70>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				reset-gpios = <&bmc_pex_irq 15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+				vdd-supply = <&p3v3_aux>;
+			};
+		};
+
+		i2c@5 {
+			reg = <5>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			smb_pex_rssd_01_16: pinctrl@20 {
+				compatible = "cypress,cy8c9560";
+				reg = <0x20>;
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				interrupt-parent = <&bmc_pex_irq>;
+				interrupts = <6 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+
+				vdd-supply = <&p3v3_aux>;
+				reset-gpios = <&bmc_pex_irq 18 GPIO_ACTIVE_HIGH>;
+
+				gpio-reserved-ranges = <48 12>;
+
+				gpio-line-names =
+				/* GPORT0 */
+				"RSSD01_SMBRST_N", "RSSD02_SMBRST_N",
+				"RSSD03_SMBRST_N", "RSSD04_SMBRST_N",
+				"RSSD05_SMBRST_N", "RSSD06_SMBRST_N",
+				"RSSD07_SMBRST_N", "RSSD08_SMBRST_N",
+				/* GPORT1 */
+				"RSSD09_SMBRST_N", "RSSD10_SMBRST_N",
+				"RSSD11_SMBRST_N", "RSSD12_SMBRST_N",
+				"RSSD13_SMBRST_N", "RSSD14_SMBRST_N",
+				"RSSD15_SMBRST_N", "RSSD16_SMBRST_N",
+				/* GPORT2 */
+				"RSSD01_PWRDIS", "RSSD02_PWRDIS",
+				"RSSD03_PWRDIS", "RSSD04_PWRDIS",
+				/* GPORT3 */
+				"RSSD05_PWRDIS", "RSSD06_PWRDIS",
+				"RSSD07_PWRDIS", "RSSD08_PWRDIS",
+				"RSSD09_PWRDIS", "RSSD10_PWRDIS",
+				"RSSD11_PWRDIS", "RSSD12_PWRDIS",
+				/* GPORT4 */
+				"RSSD13_PWRDIS", "RSSD14_PWRDIS",
+				"RSSD15_PWRDIS", "RSSD16_PWRDIS",
+				"RSSD01_RESET_N", "RSSD02_RESET_N",
+				"RSSD03_RESET_N", "RSSD04_RESET_N",
+				/* GPORT5 */
+				"RSSD05_RESET_N", "RSSD06_RESET_N",
+				"RSSD07_RESET_N", "RSSD08_RESET_N",
+				"RSSD09_RESET_N", "RSSD10_RESET_N",
+				"RSSD11_RESET_N", "RSSD12_RESET_N",
+				/* GPORT6 */
+				"RSSD13_RESET_N", "RSSD14_RESET_N",
+				"RSSD15_RESET_N", "RSSD16_RESET_N",
+				"", "",
+				"", "",
+				/* GPORT7 */
+				"", "",
+				"", "",
+				"", "",
+				"", "";
+			};
+		};
+
+		i2c@6 {
+			reg = <6>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			i2cmux11: mux@70 {
+				compatible = "maxim,max7357";
+				reg = <0x70>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				reset-gpios = <&bmc_pex_irq 12 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+				vdd-supply = <&p3v3_aux>;
+
+				i2c@0 {
+					reg = <0>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@1 {
+					reg = <1>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@2 {
+					reg = <2>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@3 {
+					reg = <3>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@4 {
+					reg = <4>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@5 {
+					reg = <5>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@6 {
+					reg = <6>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@7 {
+					reg = <7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+			};
+		};
+
+		i2c@7 {
+			reg = <7>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			i2cmux12: mux@70 {
+				compatible = "maxim,max7357";
+				reg = <0x70>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				reset-gpios = <&bmc_pex_irq 14 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+				vdd-supply = <&p3v3_aux>;
+
+				i2c@0 {
+					reg = <0>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@1 {
+					reg = <1>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@2 {
+					reg = <2>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@3 {
+					reg = <3>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@4 {
+					reg = <4>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@5 {
+					reg = <5>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@6 {
+					reg = <6>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+				i2c@7 {
+					reg = <7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+			};
+		};
+	};
+};
+
+&i2c13 {
+	status = "okay";
+
+	i2cmux23: mux@77 {
+		compatible = "maxim,max7357";
+		reg = <0x77>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reset-gpios = <&gpio0 ASPEED_GPIO(R, 4) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+		vdd-supply = <&p3v3_bmc_aux>;
+	};
+};
+
+&i2cmux23 {
+	i2c@0 {
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		smb_pex_vr_ctrl: pinctrl@20 {
+			compatible = "cypress,cy8c9540";
+			reg = <0x20>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-parent = <&gpio0>;
+			interrupts = <ASPEED_GPIO(V, 2) IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			vdd-supply = <&p3v3_bmc_aux>;
+			reset-gpios = <&gpio0 ASPEED_GPIO(Q, 2) GPIO_ACTIVE_HIGH>;
+			gpio-line-names =
+			/* GPORT0 */
+			"BCM0_INPUT_DISABLE_N", "SMB_VR_P3V3_AUX_ALERT_N",
+			"SMB_PEX_CPU1_EVENT_INT", "SMB_PEX_CPU2_EVENT_INT",
+			"DPIC0_VOLTAGE_DETECTB_N", "DPIC0_VOLTAGE_DETECTA_N",
+			"DPIC1_VOLTAGE_DETECTA_N", "DPIC1_VOLTAGE_DETECTB_N",
+			/* GPORT1 */
+			"SMB_PEX_NIC_INT", "SMB_VR_P1V05_PCH_AUX_ALERT_N",
+			"SMB_PEX_CPU0_EVENT_INT", "SMB_PEX_CPU3_EVENT_INT",
+			"LED_ID_TPM", "PLUG_DETECT_TPM",
+			"PLUG_DETECT_M2_SSD_CARRIER1", "RST_M2_SSD1_PERST_N",
+			/* GPORT2 */
+			"LED_ID_BAT", "LED_ID_MGMT_PORT2",
+			"LED_ID_MGMT_PORT1", "SMB_VR_P5V_AUX_ALERT_N",
+			/* GPORT3 */
+			"SMB_VR_AUX_SSB_ALERT_N", "BCM1_INPUT_DISABLE_N",
+			"LED_ID_NIC1_PORT1", "LED_ID_NIC1_PORT2",
+			"LED_ID_NIC2_PORT1", "LED_ID_NIC2_PORT2",
+			"RST_M2_SSD2_PERST_N", "PLUG_DETECT_M2_SSD2",
+			/* GPORT4 */
+			"PLUG_DETECT_BAT", "PLUG_DETECT_M2_SSD1",
+			"M2_SSD1_SSB_ALERT_N", "BCM2_INPUT_DISABLE_N",
+			"SMB_VR_P1V8_PCH_AUX_ALERT_N", "BCM3_INPUT_DISABLE_N",
+			"LED_PWR_DWR_BACK", "LED_ID_DWR_BACK_P",
+			/* GPORT5 */
+			"LED_ID_M2_SSD2", "LED_ID_M2_SSD1",
+			"PLUG_DETECT_M2_SSD_CARRIER2", "M2_SSD2_SSB_ALERT_N";
+
+			pinctrl-0 = <&U62120_input &U62120_input_pullup>;
+			pinctrl-names = "default";
+			U62120_input: input-pins {
+				pins = "gp10";
+				function = "gpio";
+				input-enable;
+				bias-disable;
+			};
+			U62120_input_pullup: input-pullup-pins {
+				pins = "gp01", "gp02", "gp03", "gp11", "gp12", "gp13",
+				"gp23", "gp30", "gp40", "gp42", "gp44", "gp53";
+				function = "gpio";
+				input-enable;
+				bias-pull-up;
+			};
+		};
+	};
+	i2c@1 {
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		bmc_pex_irq: pinctrl@20 {
+			compatible = "cypress,cy8c9520";
+			reg = <0x20>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-parent = <&gpio0>;
+			interrupts = <ASPEED_GPIO(V, 0) IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			vdd-supply = <&p3v3_aux>;
+			reset-gpios = <&gpio0 ASPEED_GPIO(Q, 1) GPIO_ACTIVE_HIGH>;
+			gpio-line-names =
+			/* GPORT0 */
+			"SMB_MUX_PWM_FANGRP2_RST_INT_N", "SMB_MUX_SSB_FANGRP2_RST_INT_N",
+			"SMB_MUX_PWM_FANGRP1_RST_INT_N", "SMB_MUX_SSB_RSSD01_08_RST_INT_N",
+			"SMB_MUX_RSSD01_08_RST_INT_N", "SMB_MUX_RSSD09_16_RST_INT_N",
+			"SMB_PEX_RSSD01_16_INT", "SMB_MUX_SSB_FANGRP1_RST_INT_N",
+			/* GPORT1 */
+			"SMB_SVC_PEX_FAN_ALERT_INT", "SMB_MUX_SSB_RSSD09_16_RST_INT_N",
+			"SMB_MUX_SSB_RSSD17_24_RST_INT_N", "SMB_MUX_PWM_FANGRP0_RST_INT_N",
+			"SMB_MUX_RSSD17_24_RST_INT_N", "SMB_PEX_RSSD17_32_INT",
+			"SMB_MUX_RSSD25_32_RST_INT_N", "SMB_MUX_SSB_RSSD25_32_RST_INT_N",
+			/* GPORT2 */
+			"SMB_MUX_SSB_FANGRP0_RST_INT_N", "PEX_FAN_ALERT_RST",
+			"PEX_RSSD01_16_RST", "PEX_RSSD17_32_RST";
+			pinctrl-0 = <&U60000_pins>;
+			pinctrl-names = "default";
+			U60000_pins: cfg-pins {
+				pins = "gp06", "gp10", "gp15";
+				function = "gpio";
+				input-enable;
+				bias-disable;
+			};
+		};
+	};
+	i2c@2 {
+		reg = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2cmux24: mux@70 {
+			compatible = "maxim,max7357";
+			reg = <0x70>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			vdd-supply = <&p3v3_bmc_aux>;
+		};
+	};
+	i2c@3 {
+		reg = <3>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		eeprom@51 {
+			compatible = "atmel,24c32";
+			reg = <0x51>;
+			pagesize = <32>;
+			vcc-supply = <&p3v3_bmc_aux>;
+		};
+	};
+	i2c@7 {
+		reg = <7>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2cmux25: mux@70 {
+			compatible = "maxim,max7357";
+			reg = <0x70>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&i2cmux25 {
+	reset-gpios = <&gpio0 ASPEED_GPIO(R, 2) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+	vdd-supply = <&p3v3_bmc_aux>;
+	i2c@1 {
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		p5v_aux: ir38263-p5v-aux@40 {
+			compatible = "infineon,ir38263";
+			reg = <0x40>;
+
+			regulator-name = "p5v_aux";
+			regulator-enable-ramp-delay = <2000>;
+			vin-supply = <&p12v>;
+			vbus-supply = <&p3v3_bmc_aux>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+	};
+	i2c@2 {
+		reg = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		p3v3_aux: ir38263-p3v3-aux@40 {
+			compatible = "infineon,ir38263";
+			reg = <0x40>;
+
+			vin-supply = <&p12v>;
+			regulator-name = "p3v3_aux";
+			/*
+			 * 2msec for regulator + 18msec for board capacitance
+			 * Note: Every IC has a PTC which slowly charges the bypass
+			 * cap.
+			 */
+			regulator-enable-ramp-delay = <200000>;
+		};
+	};
+	i2c@3 {
+		reg = <3>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		aux_ssb: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_pex_vr_ctrl>;
+			interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
+			vss1-supply = <&p5v_aux>;
+			vss2-supply = <&p3v3_aux>;
+			regulators {
+				p5v: sw0 {
+					regulator-name = "p5v";
+					shunt-resistor-micro-ohms = <12000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <3400000>;
+					regulator-enable-ramp-delay = <100000>;
+				};
+				p3v3_pch: sw1 {
+					regulator-name = "p3v3_pch";
+					shunt-resistor-micro-ohms = <12000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <3400000>;
+					regulator-enable-ramp-delay = <100000>;
+				};
+			};
+		};
+	};
+	i2c@4 {
+		reg = <4>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pli1209bc_p12v_a: regulator@5f {
+			compatible = "vicor,pli1209bc";
+			reg = <0x5f>;
+			regulators {
+				p12v_a: vout2 {
+					regulator-name = "bcm0";
+					regulator-boot-on;
+				};
+			};
+		};
+	};
+	i2c@5 {
+		reg = <5>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pli1209bc_p12v_b: regulator@5f {
+			compatible = "vicor,pli1209bc";
+			reg = <0x5f>;
+			regulators {
+				p12v_b: vout2 {
+					regulator-name = "bcm1";
+					regulator-boot-on;
+				};
+			};
+		};
+	};
+	i2c@6 {
+		reg = <6>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pli1209bc_p12v_c: regulator@5f {
+			compatible = "vicor,pli1209bc";
+			reg = <0x5f>;
+			regulators {
+				p12v_c: vout2 {
+					regulator-name = "bcm2";
+					regulator-boot-on;
+				};
+			};
+		};
+	};
+	i2c@7 {
+		reg = <7>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pli1209bc_p12v_d: regulator@5f {
+			compatible = "vicor,pli1209bc";
+			reg = <0x5f>;
+			regulators {
+				p12v_d: vout2 {
+					regulator-name = "bcm3";
+					regulator-boot-on;
+				};
+			};
+		};
+	};
+};
+
+&i2cmux24 {
+
+	reset-gpios = <&gpio0 ASPEED_GPIO(P, 3) (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+
+	i2c@0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0>;
+		smb_svc_pex_rssd01_16: pinctrl@20 {
+			compatible = "cypress,cy8c9560";
+			reg = <0x20>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-parent = <&gpio0>;
+			interrupts = <ASPEED_GPIO(S, 0) IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			vdd-supply = <&p3v3_bmc_aux>;
+			reset-gpios = <&smb_svc_pex_cpu0_led 17 GPIO_ACTIVE_HIGH>;
+			gpio-line-names =
+			/* GPORT0 */
+			"LED_ID_RSSD01", "LED_ID_RSSD02",
+			"LED_ID_RSSD03", "LED_ID_RSSD04",
+			"LED_ID_RSSD05", "LED_ID_RSSD06",
+			"LED_ID_RSSD07", "LED_ID_RSSD08",
+			/* GPORT1 */
+			"LED_ID_RSSD09", "LED_ID_RSSD10",
+			"LED_ID_RSSD11", "LED_ID_RSSD12",
+			"LED_ID_RSSD13", "LED_ID_RSSD14",
+			"LED_ID_RSSD15", "LED_ID_RSSD16",
+			/* GPORT2 */
+			"RSSD01_PRESENT_N", "RSSD02_PRESENT_N",
+			"RSSD03_PRESENT_N", "RSSD04_PRESENT_N",
+			/* GPORT3 */
+			"RSSD05_PRESENT_N", "RSSD06_PRESENT_N",
+			"RSSD07_PRESENT_N", "RSSD08_PRESENT_N",
+			"RSSD09_PRESENT_N", "RSSD10_PRESENT_N",
+			"RSSD11_PRESENT_N", "RSSD12_PRESENT_N",
+			/* GPORT4 */
+			"RSSD13_PRESENT_N", "RSSD14_PRESENT_N",
+			"RSSD15_PRESENT_N", "RSSD16_PRESENT_N",
+			"LED_ID_FAN_ASM01", "LED_ID_FAN_ASM02",
+			"LED_ID_FAN_ASM03", "LED_ID_FAN_ASM04",
+			/* GPORT5 */
+			"LED_ID_FAN_ASM05", "LED_ID_FAN_ASM06",
+			"PLUG_DETECT_FAN_ASM01", "PLUG_DETECT_FAN_ASM02",
+			"PLUG_DETECT_FAN_ASM03", "PLUG_DETECT_FAN_ASM04",
+			"PLUG_DETECT_FAN_ASM05", "PLUG_DETECT_FAN_ASM06",
+			/* GPORT6 */
+			"SSB_RSSD01_ALERT_N", "SSB_RSSD02_ALERT_N",
+			"SSB_RSSD03_ALERT_N", "SSB_RSSD04_ALERT_N",
+			"SSB_RSSD05_ALERT_N", "SSB_RSSD06_ALERT_N",
+			"SSB_RSSD07_ALERT_N", "SSB_RSSD08_ALERT_N",
+			/* GPORT7 */
+			"SSB_RSSD09_ALERT_N", "SSB_RSSD10_ALERT_N",
+			"SSB_RSSD11_ALERT_N", "SSB_RSSD12_ALERT_N",
+			"SSB_RSSD13_ALERT_N", "SSB_RSSD14_ALERT_N",
+			"SSB_RSSD15_ALERT_N", "SSB_RSSD16_ALERT_N";
+			pinctrl-0 = <&U65200_pins>;
+			pinctrl-names = "default";
+			U65200_pins: cfg-pins {
+				pins = "gp60", "gp61", "gp62", "gp63", "gp64",
+				       "gp65", "gp66", "gp67", "gp70", "gp71",
+				       "gp72", "gp73", "gp74", "gp75", "gp76",
+				       "gp77";
+				function = "gpio";
+				input-enable;
+				bias-pull-up;
+			};
+		};
+	};
+	i2c@1 {
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		smb_svc_pex_rssd17_32: pinctrl@20 {
+			compatible = "cypress,cy8c9560";
+			reg = <0x20>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-parent = <&gpio0>;
+			interrupts = <ASPEED_GPIO(H, 0) IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			vdd-supply = <&p3v3_bmc_aux>;
+			reset-gpios = <&smb_svc_pex_cpu1_led 17 GPIO_ACTIVE_HIGH>;
+			gpio-line-names =
+			/* GPORT0 */
+			"LED_ID_RSSD17", "LED_ID_RSSD18",
+			"LED_ID_RSSD19", "LED_ID_RSSD20",
+			"LED_ID_RSSD21", "LED_ID_RSSD22",
+			"LED_ID_RSSD23", "LED_ID_RSSD24",
+			/* GPORT1 */
+			"LED_ID_RSSD25", "LED_ID_RSSD26",
+			"LED_ID_RSSD27", "LED_ID_RSSD28",
+			"LED_ID_RSSD29", "LED_ID_RSSD30",
+			"LED_ID_RSSD31", "LED_ID_RSSD32",
+			/* GPORT2 */
+			"RSSD17_PRESENT_N", "RSSD18_PRESENT_N",
+			"RSSD19_PRESENT_N", "RSSD20_PRESENT_N",
+			/* GPORT3 */
+			"RSSD21_PRESENT_N", "RSSD22_PRESENT_N",
+			"RSSD23_PRESENT_N", "RSSD24_PRESENT_N",
+			"RSSD25_PRESENT_N", "RSSD26_PRESENT_N",
+			"RSSD27_PRESENT_N", "RSSD28_PRESENT_N",
+			/* GPORT4 */
+			"RSSD29_PRESENT_N", "RSSD30_PRESENT_N",
+			"RSSD31_PRESENT_N", "RSSD32_PRESENT_N",
+			"LED_ID_FAN_ASM07", "LED_ID_FAN_ASM08",
+			"LED_ID_FAN_ASM09", "LED_ID_FAN_ASM10",
+			/* GPORT5 */
+			"LED_ID_FAN_ASM11", "LED_ID_FAN_ASM12",
+			"PLUG_DETECT_FAN_ASM07", "PLUG_DETECT_FAN_ASM08",
+			"PLUG_DETECT_FAN_ASM09", "PLUG_DETECT_FAN_ASM10",
+			"PLUG_DETECT_FAN_ASM11", "PLUG_DETECT_FAN_ASM12",
+			/* GPORT6 */
+			"SSB_RSSD17_ALERT_N", "SSB_RSSD18_ALERT_N",
+			"SSB_RSSD19_ALERT_N", "SSB_RSSD20_ALERT_N",
+			"SSB_RSSD21_ALERT_N", "SSB_RSSD22_ALERT_N",
+			"SSB_RSSD23_ALERT_N", "SSB_RSSD24_ALERT_N",
+			/* GPORT7 */
+			"SSB_RSSD25_ALERT_N", "SSB_RSSD26_ALERT_N",
+			"SSB_RSSD27_ALERT_N", "SSB_RSSD28_ALERT_N",
+			"SSB_RSSD29_ALERT_N", "SSB_RSSD30_ALERT_N",
+			"SSB_RSSD31_ALERT_N", "SSB_RSSD32_ALERT_N";
+			pinctrl-0 = <&U65300_pins>;
+			pinctrl-names = "default";
+			U65300_pins: cfg-pins {
+				pins = "gp60", "gp61", "gp62",
+				"gp63", "gp64", "gp65", "gp66",
+				"gp67", "gp70", "gp71", "gp72",
+				"gp73", "gp74", "gp75", "gp76",
+				"gp77";
+				function = "gpio";
+				input-enable;
+				bias-pull-up;
+			};
+		};
+	};
+	i2c@2 {
+		reg = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		smb_svc_pex_cpu1_led: pinctrl@20 {
+			compatible = "cypress,cy8c9540";
+			reg = <0x20>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-parent = <&gpio0>;
+			interrupts = <ASPEED_GPIO(V, 6) IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			vdd-supply = <&p3v3_bmc_aux>;
+			reset-gpios = <&gpio0 ASPEED_GPIO(Q, 5) GPIO_ACTIVE_HIGH>;
+			gpio-reserved-ranges = <18 2>, <36 2>;
+			gpio-line-names =
+			/* GPORT0 */
+			"PLUG_DETECT_DIMM_C1E2", "PLUG_DETECT_DIMM_C1E1",
+			"PLUG_DETECT_DIMM_C1F2", "PLUG_DETECT_DIMM_C1F1",
+			"PLUG_DETECT_DIMM_C1G2", "PLUG_DETECT_DIMM_C1G1",
+			"PLUG_DETECT_DIMM_C1H2", "PLUG_DETECT_DIMM_C1H1",
+			/* GPORT1 */
+			"PLUG_DETECT_DIMM_C1D1", "PLUG_DETECT_DIMM_C1D2",
+			"PLUG_DETECT_DIMM_C1C1", "PLUG_DETECT_DIMM_C1C2",
+			"PLUG_DETECT_DIMM_C1B1", "PLUG_DETECT_DIMM_C1B2",
+			"PLUG_DETECT_DIMM_C1A1", "PLUG_DETECT_DIMM_C1A2",
+			/* GPORT2 */
+			"PEX_CPU1_EVENT_RST", "SVC_PEX_RSSD17_32_RST",
+			"", "",
+			/* GPORT3 */
+			"LED_ID_DIMM_C1E2", "LED_ID_DIMM_C1E1",
+			"LED_ID_DIMM_C1F2", "LED_ID_DIMM_C1F1",
+			"LED_ID_DIMM_C1G2", "LED_ID_DIMM_C1G1",
+			"LED_ID_DIMM_C1H2", "LED_ID_DIMM_C1H1",
+			/* GPORT4 */
+			"LED_ID_DIMM_C1A2", "LED_ID_DIMM_C1A1",
+			"LED_ID_DIMM_C1B2", "LED_ID_DIMM_C1B1",
+			"LED_ID_DIMM_C1C2", "LED_ID_DIMM_C1C1",
+			"LED_ID_DIMM_C1D2", "LED_ID_DIMM_C1D1",
+			/* GPORT5 */
+			"", "",
+			"FM_CPU1_SKTOCC_N", "LED_ID_CPU1";
+		};
+	};
+	i2c@3 {
+		reg = <3>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		smb_svc_pex_fan_alert: pinctrl@20 {
+			compatible = "cypress,cy8c9560";
+			reg = <0x20>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-parent = <&bmc_pex_irq>;
+			interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			vdd-supply = <&p3v3_aux>;
+			reset-gpios = <&bmc_pex_irq 17 GPIO_ACTIVE_HIGH>;
+			gpio-reserved-ranges = <24 3>, <51 9>;
+			gpio-line-names =
+			/* GPORT0 */
+			"FAN01_SSB_ALERT_N", "FAN02_SSB_ALERT_N",
+			"FAN03_SSB_ALERT_N", "FAN04_SSB_ALERT_N",
+			"FAN05_SSB_ALERT_N", "FAN06_SSB_ALERT_N",
+			"FAN07_SSB_ALERT_N", "FAN08_SSB_ALERT_N",
+			/* GPORT1 */
+			"FAN09_SSB_ALERT_N", "FAN10_SSB_ALERT_N",
+			"FAN11_SSB_ALERT_N", "FAN12_SSB_ALERT_N",
+			"FAN13_SSB_ALERT_N", "FAN14_SSB_ALERT_N",
+			"FAN15_SSB_ALERT_N", "FAN16_SSB_ALERT_N",
+			/* GPORT2 */
+			"FAN17_SSB_ALERT_N", "FAN18_SSB_ALERT_N",
+			"FAN19_SSB_ALERT_N", "FAN20_SSB_ALERT_N",
+			/* GPORT3 */
+			"FAN21_SSB_ALERT_N", "FAN22_SSB_ALERT_N",
+			"FAN23_SSB_ALERT_N", "FAN24_SSB_ALERT_N",
+			"", "",
+			"", "FAN01_PWM_ALERT_N",
+			/* GPORT4 */
+			"FAN02_PWM_ALERT_N", "FAN03_PWM_ALERT_N",
+			"FAN04_PWM_ALERT_N", "FAN05_PWM_ALERT_N",
+			"FAN06_PWM_ALERT_N", "FAN07_PWM_ALERT_N",
+			"FAN08_PWM_ALERT_N", "FAN09_PWM_ALERT_N",
+			/* GPORT5 */
+			"FAN10_PWM_ALERT_N", "FAN11_PWM_ALERT_N",
+			"FAN12_PWM_ALERT_N", "FAN13_PWM_ALERT_N",
+			"FAN14_PWM_ALERT_N", "FAN15_PWM_ALERT_N",
+			"FAN16_PWM_ALERT_N", "FAN17_PWM_ALERT_N",
+			/* GPORT6 */
+			"FAN18_PWM_ALERT_N", "FAN19_PWM_ALERT_N",
+			"FAN20_PWM_ALERT_N", "FAN21_PWM_ALERT_N",
+			"FAN22_PWM_ALERT_N", "FAN23_PWM_ALERT_N",
+			"FAN24_PWM_ALERT_N", "",
+			/* GPORT7 */
+			"", "",
+			"", "",
+			"", "",
+			"", "";
+			pinctrl-0 = <&U65600_pins>;
+			pinctrl-names = "default";
+			U65600_pins: cfg-pins {
+				pins = "gp00", "gp01", "gp02",
+				"gp03", "gp04", "gp05", "gp06",
+				"gp07", "gp10", "gp11", "gp12",
+				"gp13", "gp14", "gp15", "gp16",
+				"gp17", "gp20", "gp21", "gp22",
+				"gp23", "gp30", "gp31", "gp32",
+				"gp33", "gp37", "gp40", "gp41",
+				"gp42", "gp43", "gp44", "gp45",
+				"gp46", "gp47", "gp50", "gp51",
+				"gp52", "gp53", "gp54", "gp55",
+				"gp56", "gp57", "gp60", "gp61",
+				"gp62", "gp63", "gp64", "gp65",
+				"gp66";
+				function = "gpio";
+				input-enable;
+				bias-pull-up;
+			};
+		};
+	};
+	i2c@4 {
+		reg = <4>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		smb_svc_pex_cpu2_led: pinctrl@20 {
+			compatible = "cypress,cy8c9540";
+			reg = <0x20>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-parent = <&gpio0>;
+			interrupts = <ASPEED_GPIO(V, 5) IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			vdd-supply = <&p3v3_bmc_aux>;
+			reset-gpios = <&gpio0 ASPEED_GPIO(Q, 6) GPIO_ACTIVE_HIGH>;
+			gpio-reserved-ranges = <17 3>, <36 2>;
+			gpio-line-names =
+			/* GPORT0 */
+			"PLUG_DETECT_DIMM_C2E2", "PLUG_DETECT_DIMM_C2E1",
+			"PLUG_DETECT_DIMM_C2F2", "PLUG_DETECT_DIMM_C2F1",
+			"PLUG_DETECT_DIMM_C2G2", "PLUG_DETECT_DIMM_C2G1",
+			"PLUG_DETECT_DIMM_C2H2", "PLUG_DETECT_DIMM_C2H1",
+			/* GPORT1 */
+			"PLUG_DETECT_DIMM_C2D1", "PLUG_DETECT_DIMM_C2D2",
+			"PLUG_DETECT_DIMM_C2C1", "PLUG_DETECT_DIMM_C2C2",
+			"PLUG_DETECT_DIMM_C2B1", "PLUG_DETECT_DIMM_C2B2",
+			"PLUG_DETECT_DIMM_C2A1", "PLUG_DETECT_DIMM_C2A2",
+			/* GPORT2 */
+			"PEX_CPU2_EVENT_RST", "",
+			"", "",
+			/* GPORT3 */
+			"LED_ID_DIMM_C2E2", "LED_ID_DIMM_C2E1",
+			"LED_ID_DIMM_C2F2", "LED_ID_DIMM_C2F1",
+			"LED_ID_DIMM_C2G2", "LED_ID_DIMM_C2G1",
+			"LED_ID_DIMM_C2H2", "LED_ID_DIMM_C2H1",
+			/* GPORT4 */
+			"LED_ID_DIMM_C2A2", "LED_ID_DIMM_C2A1",
+			"LED_ID_DIMM_C2B2", "LED_ID_DIMM_C2B1",
+			"LED_ID_DIMM_C2C2", "LED_ID_DIMM_C2C1",
+			"LED_ID_DIMM_C2D2", "LED_ID_DIMM_C2D1",
+			/* GPORT5 */
+			"", "",
+			"FM_CPU2_SKTOCC_N", "LED_ID_CPU2";
+		};
+	};
+	i2c@5 {
+		reg = <5>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		smb_svc_pex_cpu3_led: pinctrl@20 {
+			compatible = "cypress,cy8c9540";
+			reg = <0x20>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-parent = <&gpio0>;
+			interrupts = <ASPEED_GPIO(V, 3) IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			vdd-supply = <&p3v3_bmc_aux>;
+			reset-gpios = <&gpio0 ASPEED_GPIO(Q, 7) GPIO_ACTIVE_HIGH>;
+			gpio-reserved-ranges = <17 3>;
+			gpio-line-names =
+			/* GPORT0 */
+			"PLUG_DETECT_DIMM_C3E2", "PLUG_DETECT_DIMM_C3E1",
+			"PLUG_DETECT_DIMM_C3F2", "PLUG_DETECT_DIMM_C3F1",
+			"PLUG_DETECT_DIMM_C3G2", "PLUG_DETECT_DIMM_C3G1",
+			"PLUG_DETECT_DIMM_C3H2", "PLUG_DETECT_DIMM_C3H1",
+			/* GPORT1 */
+			"PLUG_DETECT_DIMM_C3D1", "PLUG_DETECT_DIMM_C3D2",
+			"PLUG_DETECT_DIMM_C3C1", "PLUG_DETECT_DIMM_C3C2",
+			"PLUG_DETECT_DIMM_C3B1", "PLUG_DETECT_DIMM_C3B2",
+			"PLUG_DETECT_DIMM_C3A1", "PLUG_DETECT_DIMM_C3A2",
+			/* GPORT2 */
+			"PEX_CPU3_EVENT_RST", "",
+			"", "",
+			/* GPORT3 */
+			"LED_ID_DIMM_C3E2", "LED_ID_DIMM_C3E1",
+			"LED_ID_DIMM_C3F2", "LED_ID_DIMM_C3F1",
+			"LED_ID_DIMM_C3G2", "LED_ID_DIMM_C3G1",
+			"LED_ID_DIMM_C3H2", "LED_ID_DIMM_C3H1",
+			/* GPORT4 */
+			"LED_ID_DIMM_C3A2", "LED_ID_DIMM_C3A1",
+			"LED_ID_DIMM_C3B2", "LED_ID_DIMM_C3B1",
+			"LED_ID_DIMM_C3C2", "LED_ID_DIMM_C3C1",
+			"LED_ID_DIMM_C3D2", "LED_ID_DIMM_C3D1",
+			/* GPORT5 */
+			"LED_PWR_DWR_FRNT", "LED_ID_DWR_FRNT_P",
+			"FM_CPU3_SKTOCC_N", "LED_ID_CPU3";
+		};
+	};
+	i2c@6 {
+		reg = <6>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		smb_svc_pex_cpu0_led: pinctrl@20 {
+			compatible = "cypress,cy8c9540";
+			reg = <0x20>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-parent = <&gpio0>;
+			interrupts = <ASPEED_GPIO(O, 3) IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			vdd-supply = <&p3v3_bmc_aux>;
+			reset-gpios = <&gpio0 ASPEED_GPIO(Q, 4) GPIO_ACTIVE_HIGH>;
+			gpio-reserved-ranges = <18 2>, <36 2>;
+			gpio-line-names =
+			/* GPORT0 */
+			"PLUG_DETECT_DIMM_C0E2", "PLUG_DETECT_DIMM_C0E1",
+			"PLUG_DETECT_DIMM_C0F2", "PLUG_DETECT_DIMM_C0F1",
+			"PLUG_DETECT_DIMM_C0G2", "PLUG_DETECT_DIMM_C0G1",
+			"PLUG_DETECT_DIMM_C0H2", "PLUG_DETECT_DIMM_C0H1",
+			/* GPORT1 */
+			"PLUG_DETECT_DIMM_C0D1", "PLUG_DETECT_DIMM_C0D2",
+			"PLUG_DETECT_DIMM_C0C1", "PLUG_DETECT_DIMM_C0C2",
+			"PLUG_DETECT_DIMM_C0B1", "PLUG_DETECT_DIMM_C0B2",
+			"PLUG_DETECT_DIMM_C0A1", "PLUG_DETECT_DIMM_C0A2",
+			/* GPORT2 */
+			"PEX_CPU0_EVENT_RST", "SVC_PEX_RSSD01_16_RST",
+			"", "",
+			/* GPORT3 */
+			"LED_ID_DIMM_C0E2", "LED_ID_DIMM_C0E1",
+			"LED_ID_DIMM_C0F2", "LED_ID_DIMM_C0F1",
+			"LED_ID_DIMM_C0G2", "LED_ID_DIMM_C0G1",
+			"LED_ID_DIMM_C0H2", "LED_ID_DIMM_C0H1",
+			/* GPORT4 */
+			"LED_ID_DIMM_C0A2", "LED_ID_DIMM_C0A1",
+			"LED_ID_DIMM_C0B2", "LED_ID_DIMM_C0B1",
+			"LED_ID_DIMM_C0C2", "LED_ID_DIMM_C0C1",
+			"LED_ID_DIMM_C0D2", "LED_ID_DIMM_C0D1",
+			/* GPORT5 */
+			"", "",
+			"FM_CPU0_SKTOCC_N", "LED_ID_CPU0";
+		};
+	};
+};
+
+&i2c9 {
+	status = "okay";
+
+	p1v2_bmc_aux_mon: pmic@60 {
+		compatible = "maxim,max8952";
+		reg = <0x60>;
+		max8952,default-mode = <3>;
+		max8952,dvs-mode-microvolt = <1100000>, <1100000>,
+					     <1100000>, <1100000>;
+		max8952,sync-freq = <0>;
+		max8952,ramp-speed = <0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&i2cmux8 {
+	i2c@0 {
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan10_ssb: regulator@3a {
+			compatible = "maxim,max5978";
+			reg = <0x3a>;
+			vss1-supply = <&p12v>;
+			interrupt-parent = <&smb_svc_pex_fan_alert>;
+			interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+
+			regulators {
+				sw0_fan10_ssb: sw0 {
+					regulator-name = "fan10_supply";
+					shunt-resistor-micro-ohms = <10000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <3400000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+
+	};
+	i2c@1 {
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan12_ssb: regulator@3a {
+			compatible = "maxim,max5978";
+			reg = <0x3a>;
+			vss1-supply = <&p12v>;
+			interrupt-parent = <&smb_svc_pex_fan_alert>;
+			interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+
+			regulators {
+				sw0_fan12_ssb: sw0 {
+					regulator-name = "fan12_supply";
+					shunt-resistor-micro-ohms = <10000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <3400000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+
+	};
+	i2c@2 {
+		reg = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan14_ssb: regulator@3a {
+			compatible = "maxim,max5978";
+			reg = <0x3a>;
+			vss1-supply = <&p12v>;
+			interrupt-parent = <&smb_svc_pex_fan_alert>;
+			interrupts = <13 IRQ_TYPE_LEVEL_LOW>;
+
+			regulators {
+				sw0_fan14_ssb: sw0 {
+					regulator-name = "fan14_supply";
+					shunt-resistor-micro-ohms = <10000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <3400000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@3 {
+		reg = <3>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan16_ssb: regulator@3a {
+			compatible = "maxim,max5978";
+			reg = <0x3a>;
+			vss1-supply = <&p12v>;
+			interrupt-parent = <&smb_svc_pex_fan_alert>;
+			interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+
+			regulators {
+				sw0_fan16_ssb: sw0 {
+					regulator-name = "fan16_supply";
+					shunt-resistor-micro-ohms = <10000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <3400000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@4 {
+		reg = <4>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan18_ssb: regulator@3a {
+			compatible = "maxim,max5978";
+			reg = <0x3a>;
+			vss1-supply = <&p12v>;
+			interrupt-parent = <&smb_svc_pex_fan_alert>;
+			interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+
+			regulators {
+				sw0_fan18_ssb: sw0 {
+					regulator-name = "fan18_supply";
+					shunt-resistor-micro-ohms = <10000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <3400000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@5 {
+		reg = <5>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan20_ssb: regulator@3a {
+			compatible = "maxim,max5978";
+			reg = <0x3a>;
+			vss1-supply = <&p12v>;
+			interrupt-parent = <&smb_svc_pex_fan_alert>;
+			interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+
+			regulators {
+				sw0_fan20_ssb: sw0 {
+					regulator-name = "fan20_supply";
+					shunt-resistor-micro-ohms = <10000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <3400000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@6 {
+		reg = <6>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan22_ssb: regulator@3a {
+			compatible = "maxim,max5978";
+			reg = <0x3a>;
+			vss1-supply = <&p12v>;
+			interrupt-parent = <&smb_svc_pex_fan_alert>;
+			interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
+
+			regulators {
+				sw0_fan22_ssb: sw0 {
+					regulator-name = "fan22_supply";
+					shunt-resistor-micro-ohms = <10000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <3400000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@7 {
+		reg = <7>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan24_ssb: regulator@3a {
+			compatible = "maxim,max5978";
+			reg = <0x3a>;
+			vss1-supply = <&p12v>;
+			interrupt-parent = <&smb_svc_pex_fan_alert>;
+			interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
+
+			regulators {
+				sw0_fan24_ssb: sw0 {
+					regulator-name = "fan24_supply";
+					shunt-resistor-micro-ohms = <10000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <3400000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+};
+
+&i2cmux7 {
+	i2c@0 {
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan17_ssb: regulator@3a {
+			compatible = "maxim,max5978";
+			reg = <0x3a>;
+			vss1-supply = <&p12v>;
+			interrupt-parent = <&smb_svc_pex_fan_alert>;
+			interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
+
+			regulators {
+				sw0_fan17_ssb: sw0 {
+					regulator-name = "fan17_supply";
+					shunt-resistor-micro-ohms = <10000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <3400000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@1 {
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan19_ssb: regulator@3a {
+			compatible = "maxim,max5978";
+			reg = <0x3a>;
+			vss1-supply = <&p12v>;
+			interrupt-parent = <&smb_svc_pex_fan_alert>;
+			interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
+
+			regulators {
+				sw0_fan19_ssb: sw0 {
+					regulator-name = "fan19_supply";
+					shunt-resistor-micro-ohms = <10000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <3400000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@2 {
+		reg = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan21_ssb: regulator@3a {
+			compatible = "maxim,max5978";
+			reg = <0x3a>;
+			vss1-supply = <&p12v>;
+			interrupt-parent = <&smb_svc_pex_fan_alert>;
+			interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
+
+			regulators {
+				sw0_fan21_ssb: sw0 {
+					regulator-name = "fan21_supply";
+					shunt-resistor-micro-ohms = <10000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <3400000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@3 {
+		reg = <3>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan23_ssb: regulator@3a {
+			compatible = "maxim,max5978";
+			reg = <0x3a>;
+			vss1-supply = <&p12v>;
+			interrupt-parent = <&smb_svc_pex_fan_alert>;
+			interrupts = <22 IRQ_TYPE_LEVEL_LOW>;
+
+			regulators {
+				sw0_fan23_ssb: sw0 {
+					regulator-name = "fan23_supply";
+					shunt-resistor-micro-ohms = <10000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <3400000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@4 {
+		reg = <4>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan02_ssb: regulator@3a {
+			compatible = "maxim,max5978";
+			reg = <0x3a>;
+			vss1-supply = <&p12v>;
+			interrupt-parent = <&smb_svc_pex_fan_alert>;
+			interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+
+			regulators {
+				sw0_fan02_ssb: sw0 {
+					regulator-name = "fan02_supply";
+					shunt-resistor-micro-ohms = <10000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <3400000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@5 {
+		reg = <5>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan04_ssb: regulator@3a {
+			compatible = "maxim,max5978";
+			reg = <0x3a>;
+			vss1-supply = <&p12v>;
+			interrupt-parent = <&smb_svc_pex_fan_alert>;
+			interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+
+			regulators {
+				sw0_fan04_ssb: sw0 {
+					regulator-name = "fan04_supply";
+					shunt-resistor-micro-ohms = <10000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <3400000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@6 {
+		reg = <6>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan06_ssb: regulator@3a {
+			compatible = "maxim,max5978";
+			reg = <0x3a>;
+			vss1-supply = <&p12v>;
+			interrupt-parent = <&smb_svc_pex_fan_alert>;
+			interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+
+			regulators {
+				sw0_fan06_ssb: sw0 {
+					regulator-name = "fan06_supply";
+					shunt-resistor-micro-ohms = <10000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <3400000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@7 {
+		reg = <7>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan08_ssb: regulator@3a {
+			compatible = "maxim,max5978";
+			reg = <0x3a>;
+			vss1-supply = <&p12v>;
+			interrupt-parent = <&smb_svc_pex_fan_alert>;
+			interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+
+			regulators {
+				sw0_fan08_ssb: sw0 {
+					regulator-name = "fan08_supply";
+					shunt-resistor-micro-ohms = <10000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <3400000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+};
+
+&i2cmux6 {
+	i2c@0 {
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan01_ssb: regulator@3a {
+			compatible = "maxim,max5978";
+			reg = <0x3a>;
+			vss1-supply = <&p12v>;
+			interrupt-parent = <&smb_svc_pex_fan_alert>;
+			interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+			regulators {
+				sw0_fan01_ssb: sw0 {
+					regulator-name = "fan01_supply";
+					shunt-resistor-micro-ohms = <10000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <3400000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@1 {
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan03_ssb: regulator@3a {
+			compatible = "maxim,max5978";
+			reg = <0x3a>;
+			vss1-supply = <&p12v>;
+			interrupt-parent = <&smb_svc_pex_fan_alert>;
+			interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+
+			regulators {
+				sw0_fan03_ssb: sw0 {
+					regulator-name = "fan03_supply";
+
+					shunt-resistor-micro-ohms = <10000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <3400000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@2 {
+		reg = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan05_ssb: regulator@3a {
+			compatible = "maxim,max5978";
+			reg = <0x3a>;
+			vss1-supply = <&p12v>;
+			interrupt-parent = <&smb_svc_pex_fan_alert>;
+			interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+
+			regulators {
+				sw0_fan05_ssb: sw0 {
+					regulator-name = "fan05_supply";
+					shunt-resistor-micro-ohms = <10000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <3400000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@3 {
+		reg = <3>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan07_ssb: regulator@3a {
+			compatible = "maxim,max5978";
+			reg = <0x3a>;
+			vss1-supply = <&p12v>;
+			interrupt-parent = <&smb_svc_pex_fan_alert>;
+			interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
+
+			regulators {
+				sw0_fan07_ssb: sw0 {
+					regulator-name = "fan07_supply";
+					shunt-resistor-micro-ohms = <10000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <3400000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@4 {
+		reg = <4>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan09_ssb: regulator@3a {
+			compatible = "maxim,max5978";
+			reg = <0x3a>;
+			vss1-supply = <&p12v>;
+			interrupt-parent = <&smb_svc_pex_fan_alert>;
+			interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+
+			regulators {
+				sw0_fan09_ssb: sw0 {
+					regulator-name = "fan09_supply";
+					shunt-resistor-micro-ohms = <10000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <3400000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@5 {
+		reg = <5>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan11_ssb: regulator@3a {
+			compatible = "maxim,max5978";
+			reg = <0x3a>;
+			vss1-supply = <&p12v>;
+			interrupt-parent = <&smb_svc_pex_fan_alert>;
+			interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
+
+			regulators {
+				sw0_fan11_ssb: sw0 {
+					regulator-name = "fan11_supply";
+					shunt-resistor-micro-ohms = <10000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <3400000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@6 {
+		reg = <6>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan13_ssb: regulator@3a {
+			compatible = "maxim,max5978";
+			reg = <0x3a>;
+			vss1-supply = <&p12v>;
+			interrupt-parent = <&smb_svc_pex_fan_alert>;
+			interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+
+			regulators {
+				sw0_fan13_ssb: sw0 {
+					regulator-name = "fan13_supply";
+					shunt-resistor-micro-ohms = <10000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <3400000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@7 {
+		reg = <7>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan15_ssb: regulator@3a {
+			compatible = "maxim,max5978";
+			reg = <0x3a>;
+			vss1-supply = <&p12v>;
+			interrupt-parent = <&smb_svc_pex_fan_alert>;
+			interrupts = <14 IRQ_TYPE_LEVEL_LOW>;
+
+			regulators {
+				sw0_fan15_ssb: sw0 {
+					regulator-name = "fan15_supply";
+					shunt-resistor-micro-ohms = <10000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <3400000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+
+	};
+};
+
+&i2cmux9 {
+	i2c@0 {
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd19: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd17_32>;
+			interrupts = <46 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd19:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd19: sw0 {
+					regulator-name = "rssd19_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd19: sw1 {
+					regulator-name = "rssd19_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@1 {
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd18: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd17_32>;
+			interrupts = <45 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd18:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd18: sw0 {
+					regulator-name = "rssd18_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd18: sw1 {
+					regulator-name = "rssd18_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@2 {
+		reg = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd17: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd17_32>;
+			interrupts = <44 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd17:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd17: sw0 {
+					regulator-name = "rssd17_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd17: sw1 {
+					regulator-name = "rssd17_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@3 {
+		reg = <3>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd20: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd17_32>;
+			interrupts = <47 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd20:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd20: sw0 {
+					regulator-name = "rssd20_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd20: sw1 {
+					regulator-name = "rssd20_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@4 {
+		reg = <4>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd21: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd17_32>;
+			interrupts = <48 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd21:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd21: sw0 {
+					regulator-name = "rssd21_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd21: sw1 {
+					regulator-name = "rssd21_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@5 {
+		reg = <5>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd22: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd17_32>;
+			interrupts = <49 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd22:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd22: sw0 {
+					regulator-name = "rssd22_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd22: sw1 {
+					regulator-name = "rssd22_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@6 {
+		reg = <6>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd24: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd17_32>;
+			interrupts = <51 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd24:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd24: sw0 {
+					regulator-name = "rssd24_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd24: sw1 {
+					regulator-name = "rssd24_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@7 {
+		reg = <7>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd23: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd17_32>;
+			interrupts = <50 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd23:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd23: sw0 {
+					regulator-name = "rssd23_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd23: sw1 {
+					regulator-name = "rssd23_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+};
+
+&i2cmux10 {
+	i2c@0 {
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd25: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd17_32>;
+			interrupts = <52 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd25:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd25: sw0 {
+					regulator-name = "rssd25_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd25: sw1 {
+					regulator-name = "rssd25_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@1 {
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd26: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd17_32>;
+			interrupts = <53 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd26:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd26: sw0 {
+					regulator-name = "rssd26_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd26: sw1 {
+					regulator-name = "rssd26_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@2 {
+		reg = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd27: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd17_32>;
+			interrupts = <54 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd27:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd27: sw0 {
+					regulator-name = "rssd27_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd27: sw1 {
+					regulator-name = "rssd27_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@3 {
+		reg = <3>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd32: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd17_32>;
+			interrupts = <59 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd32:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd32: sw0 {
+					regulator-name = "rssd32_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd32: sw1 {
+					regulator-name = "rssd32_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@4 {
+		reg = <4>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd31: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd17_32>;
+			interrupts = <58 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd31:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd31: sw0 {
+					regulator-name = "rssd31_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd31: sw1 {
+					regulator-name = "rssd31_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@5 {
+		reg = <5>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd30: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd17_32>;
+			interrupts = <57 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd30:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd30: sw0 {
+					regulator-name = "rssd30_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd30: sw1 {
+					regulator-name = "rssd30_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@6 {
+		reg = <6>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd29: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd17_32>;
+			interrupts = <56 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd29:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd29: sw0 {
+					regulator-name = "rssd29_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd29: sw1 {
+					regulator-name = "rssd29_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@7 {
+		reg = <7>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd28: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd17_32>;
+			interrupts = <55 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd28:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd28: sw0 {
+					regulator-name = "rssd28_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd28: sw1 {
+					regulator-name = "rssd28_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+};
+
+&i2cmux18 {
+	i2c@0 {
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd03: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd01_16>;
+			interrupts = <46 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd03:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd03: sw0 {
+					regulator-name = "rssd03_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd03: sw1 {
+					regulator-name = "rssd03_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@1 {
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd02: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd01_16>;
+			interrupts = <45 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd02:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd02: sw0 {
+					regulator-name = "rssd02_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd02: sw1 {
+					regulator-name = "rssd02_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@2 {
+		reg = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd01: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd01_16>;
+			interrupts = <44 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd01:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd01: sw0 {
+					regulator-name = "rssd01_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd01: sw1 {
+					regulator-name = "rssd01_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@3 {
+		reg = <3>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd04: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd01_16>;
+			interrupts = <47 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd04:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd04: sw0 {
+					regulator-name = "rssd04_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd04: sw1 {
+					regulator-name = "rssd04_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@4 {
+		reg = <4>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd05: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd01_16>;
+			interrupts = <48 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd05:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd05: sw0 {
+					regulator-name = "rssd05_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd05: sw1 {
+					regulator-name = "rssd05_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@5 {
+		reg = <5>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd08: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd01_16>;
+			interrupts = <51 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd08:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd08: sw0 {
+					regulator-name = "rssd08_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd08: sw1 {
+					regulator-name = "rssd08_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@6 {
+		reg = <6>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd07: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd01_16>;
+			interrupts = <50 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd07:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd07: sw0 {
+					regulator-name = "rssd07_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd07: sw1 {
+					regulator-name = "rssd07_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@7 {
+		reg = <7>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd06: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd01_16>;
+			interrupts = <49 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd06:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd06: sw0 {
+					regulator-name = "rssd06_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd06: sw1 {
+					regulator-name = "rssd06_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+};
+
+&i2cmux19 {
+	i2c@0 {
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd14: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd01_16>;
+			interrupts = <57 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd14:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd14: sw0 {
+					regulator-name = "rssd14_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd14: sw1 {
+					regulator-name = "rssd14_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@1 {
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd13: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd01_16>;
+			interrupts = <56 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd13:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd13: sw0 {
+					regulator-name = "rssd13_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd13: sw1 {
+					regulator-name = "rssd13_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@2 {
+		reg = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd12: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd01_16>;
+			interrupts = <55 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd12:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd12: sw0 {
+					regulator-name = "rssd12_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd12: sw1 {
+					regulator-name = "rssd12_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@3 {
+		reg = <3>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd11: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd01_16>;
+			interrupts = <54 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd11:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd11: sw0 {
+					regulator-name = "rssd11_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd11: sw1 {
+					regulator-name = "rssd11_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@4 {
+		reg = <4>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd10: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd01_16>;
+			interrupts = <53 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd10:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd10: sw0 {
+					regulator-name = "rssd10_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd10: sw1 {
+					regulator-name = "rssd10_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@5 {
+		reg = <5>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd09: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd01_16>;
+			interrupts = <52 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd09:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd09: sw0 {
+					regulator-name = "rssd09_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd09: sw1 {
+					regulator-name = "rssd09_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@6 {
+		reg = <6>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd15: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd01_16>;
+			interrupts = <58 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd15:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd15: sw0 {
+					regulator-name = "rssd15_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd15: sw1 {
+					regulator-name = "rssd15_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+	i2c@7 {
+		reg = <7>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ssb_rssd16: regulator@3a {
+			compatible = "maxim,max5970";
+			reg = <0x3a>;
+			interrupt-parent = <&smb_svc_pex_rssd01_16>;
+			interrupts = <59 IRQ_TYPE_LEVEL_LOW>;
+
+			vss1-supply = <&p3v3_aux>;
+			vss2-supply = <&p12v>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					label = "rssd16:green:power";
+					default-state = "off";
+				};
+			};
+
+			regulators {
+				sw0_ssb_rssd16: sw0 {
+					regulator-name = "rssd16_12v";
+					shunt-resistor-micro-ohms = <9000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <4500000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+				sw1_ssb_rssd16: sw1 {
+					regulator-name = "rssd16_3v3";
+					shunt-resistor-micro-ohms = <100000>;
+					regulator-over-current-protection;
+					regulator-oc-protection-microamp = <410000>;
+					regulator-enable-ramp-delay = <1000>;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-system1.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-system1.dts
new file mode 100644
index 000000000000..c8267c97a44e
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ibm-system1.dts
@@ -0,0 +1,1671 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2023 IBM Corp.
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/leds/leds-pca955x.h>
+
+/ {
+	model = "System1";
+	compatible = "ibm,system1-bmc", "aspeed,ast2600";
+
+	aliases {
+		i2c16 = &i2c8mux1chn0;
+		i2c17 = &i2c8mux1chn1;
+		i2c18 = &i2c8mux1chn2;
+		i2c19 = &i2c8mux1chn3;
+		i2c20 = &i2c8mux1chn4;
+		i2c21 = &i2c8mux1chn5;
+		i2c22 = &i2c8mux1chn6;
+		i2c23 = &i2c8mux1chn7;
+		i2c24 = &i2c3mux0chn0;
+		i2c25 = &i2c3mux0chn1;
+		i2c26 = &i2c3mux0chn2;
+		i2c27 = &i2c3mux0chn3;
+		i2c28 = &i2c3mux0chn4;
+		i2c29 = &i2c3mux0chn5;
+		i2c30 = &i2c3mux0chn6;
+		i2c31 = &i2c3mux0chn7;
+		i2c32 = &i2c6mux0chn0;
+		i2c33 = &i2c6mux0chn1;
+		i2c34 = &i2c6mux0chn2;
+		i2c35 = &i2c6mux0chn3;
+		i2c36 = &i2c6mux0chn4;
+		i2c37 = &i2c6mux0chn5;
+		i2c38 = &i2c6mux0chn6;
+		i2c39 = &i2c6mux0chn7;
+		i2c40 = &i2c7mux0chn0;
+		i2c41 = &i2c7mux0chn1;
+		i2c42 = &i2c7mux0chn2;
+		i2c43 = &i2c7mux0chn3;
+		i2c44 = &i2c7mux0chn4;
+		i2c45 = &i2c7mux0chn5;
+		i2c46 = &i2c7mux0chn6;
+		i2c47 = &i2c7mux0chn7;
+		i2c48 = &i2c8mux0chn0;
+		i2c49 = &i2c8mux0chn1;
+		i2c50 = &i2c8mux0chn2;
+		i2c51 = &i2c8mux0chn3;
+		i2c52 = &i2c8mux0chn4;
+		i2c53 = &i2c8mux0chn5;
+		i2c54 = &i2c8mux0chn6;
+		i2c55 = &i2c8mux0chn7;
+		i2c56 = &i2c14mux0chn0;
+		i2c57 = &i2c14mux0chn1;
+		i2c58 = &i2c14mux0chn2;
+		i2c59 = &i2c14mux0chn3;
+		i2c60 = &i2c14mux0chn4;
+		i2c61 = &i2c14mux0chn5;
+		i2c62 = &i2c14mux0chn6;
+		i2c63 = &i2c14mux0chn7;
+		i2c64 = &i2c15mux0chn0;
+		i2c65 = &i2c15mux0chn1;
+		i2c66 = &i2c15mux0chn2;
+		i2c67 = &i2c15mux0chn3;
+		i2c68 = &i2c15mux0chn4;
+		i2c69 = &i2c15mux0chn5;
+		i2c70 = &i2c15mux0chn6;
+		i2c71 = &i2c15mux0chn7;
+	};
+
+	chosen {
+		stdout-path = "uart5:115200n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		eventlog: tcg-event-log@b3d00000 {
+			no-map;
+			reg = <0xb3d00000 0x100000>;
+		};
+
+		ramoops@b3e00000 {
+			compatible = "ramoops";
+			reg = <0xb3e00000 0x200000>; /* 16 * (4 * 0x8000) */
+			record-size = <0x8000>;
+			console-size = <0x8000>;
+			ftrace-size = <0x8000>;
+			pmsg-size = <0x8000>;
+			max-reason = <3>; /* KMSG_DUMP_EMERG */
+		};
+
+		/* LPC FW cycle bridge region requires natural alignment */
+		flash_memory: region@b4000000 {
+			no-map;
+			reg = <0xb4000000 0x04000000>; /* 64M */
+		};
+
+		/* VGA region is dictated by hardware strapping */
+		vga_memory: region@bf000000 {
+			no-map;
+			compatible = "shared-dma-pool";
+			reg = <0xbf000000 0x01000000>;  /* 16M */
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-bmc-ready {
+			gpios = <&gpio0 ASPEED_GPIO(L, 7) GPIO_ACTIVE_HIGH>;
+		};
+
+		led-bmc-hb {
+			gpios = <&gpio0 ASPEED_GPIO(P, 7) GPIO_ACTIVE_HIGH>;
+		};
+
+		led-rear-enc-fault0 {
+			gpios = <&gpio0 ASPEED_GPIO(S, 6) GPIO_ACTIVE_HIGH>;
+		};
+
+		led-rear-enc-id0 {
+			gpios = <&gpio0 ASPEED_GPIO(S, 7) GPIO_ACTIVE_HIGH>;
+		};
+
+		led-fan0-fault {
+			gpios = <&pca3 5 GPIO_ACTIVE_LOW>;
+		};
+
+		led-fan1-fault {
+			gpios = <&pca3 6 GPIO_ACTIVE_LOW>;
+		};
+
+		led-fan2-fault {
+			gpios = <&pca3 7 GPIO_ACTIVE_LOW>;
+		};
+
+		led-fan3-fault {
+			gpios = <&pca3 8 GPIO_ACTIVE_LOW>;
+		};
+
+		led-fan4-fault {
+			gpios = <&pca3 9 GPIO_ACTIVE_LOW>;
+		};
+
+		led-fan5-fault {
+			gpios = <&pca3 10 GPIO_ACTIVE_LOW>;
+		};
+
+		led-fan6-fault {
+			gpios = <&pca3 11 GPIO_ACTIVE_LOW>;
+		};
+
+		led-nvmed0-fault {
+			gpios = <&pca4 4 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-nvmed1-fault {
+			gpios = <&pca4 5 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-nvmed2-fault {
+			gpios = <&pca4 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-nvmed3-fault {
+			gpios = <&pca4 7 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		poll-interval = <1000>;
+
+		event-nvme0-presence {
+			label = "nvme0-presence";
+			gpios = <&pca4 0 GPIO_ACTIVE_LOW>;
+			linux,code = <0>;
+		};
+
+		event-nvme1-presence {
+			label = "nvme1-presence";
+			gpios = <&pca4 1 GPIO_ACTIVE_LOW>;
+			linux,code = <1>;
+		};
+
+		event-nvme2-presence {
+			label = "nvme2-presence";
+			gpios = <&pca4 2 GPIO_ACTIVE_LOW>;
+			linux,code = <2>;
+		};
+
+		event-nvme3-presence {
+			label = "nvme3-presence";
+			gpios = <&pca4 3 GPIO_ACTIVE_LOW>;
+			linux,code = <3>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&p12v_vd 0>, <&p5v_aux_vd 0>,
+			<&p5v_bmc_aux_vd 0>, <&p3v3_aux_vd 0>,
+			<&p3v3_bmc_aux_vd 0>, <&p1v8_bmc_aux_vd 0>,
+			<&adc1 4>, <&adc0 2>, <&adc1 0>,
+			<&p2v5_aux_vd 0>, <&adc1 7>;
+	};
+
+	p12v_vd: voltage-divider1 {
+		compatible = "voltage-divider";
+		io-channels = <&adc1 3>;
+		#io-channel-cells = <1>;
+
+		/*
+		 * Scale the system voltage by 1127/127 to fit the ADC range.
+		 * Use small nominator to prevent integer overflow.
+		 */
+		output-ohms = <15>;
+		full-ohms = <133>;
+	};
+
+	p5v_aux_vd: voltage-divider2 {
+		compatible = "voltage-divider";
+		io-channels = <&adc1 5>;
+		#io-channel-cells = <1>;
+
+		/*
+		 * Scale the system voltage by 1365/365 to fit the ADC range.
+		 * Use small nominator to prevent integer overflow.
+		 */
+		output-ohms = <50>;
+		full-ohms = <187>;
+	};
+
+	p5v_bmc_aux_vd: voltage-divider3 {
+		compatible = "voltage-divider";
+		io-channels = <&adc0 3>;
+		#io-channel-cells = <1>;
+
+		/*
+		 * Scale the system voltage by 1365/365 to fit the ADC range.
+		 * Use small nominator to prevent integer overflow.
+		 */
+		output-ohms = <50>;
+		full-ohms = <187>;
+	};
+
+	p3v3_aux_vd: voltage-divider4 {
+		compatible = "voltage-divider";
+		io-channels = <&adc1 2>;
+		#io-channel-cells = <1>;
+
+		/*
+		 * Scale the system voltage by 1698/698 to fit the ADC range.
+		 * Use small nominator to prevent integer overflow.
+		 */
+		output-ohms = <14>;
+		full-ohms = <34>;
+	};
+
+	p3v3_bmc_aux_vd: voltage-divider5 {
+		compatible = "voltage-divider";
+		io-channels = <&adc0 7>;
+		#io-channel-cells = <1>;
+
+		/*
+		 * Scale the system voltage by 1698/698 to fit the ADC range.
+		 * Use small nominator to prevent integer overflow.
+		 */
+		output-ohms = <14>;
+		full-ohms = <34>;
+	};
+
+	p1v8_bmc_aux_vd: voltage-divider6 {
+		compatible = "voltage-divider";
+		io-channels = <&adc0 6>;
+		#io-channel-cells = <1>;
+
+		/*
+		 * Scale the system voltage by 4000/3000 to fit the ADC range.
+		 * Use small nominator to prevent integer overflow.
+		 */
+		output-ohms = <3>;
+		full-ohms = <4>;
+	};
+
+	p2v5_aux_vd: voltage-divider7 {
+		compatible = "voltage-divider";
+		io-channels = <&adc1 1>;
+		#io-channel-cells = <1>;
+
+		/*
+		 * Scale the system voltage by 2100/1100 to fit the ADC range.
+		 * Use small nominator to prevent integer overflow.
+		 */
+		output-ohms = <11>;
+		full-ohms = <21>;
+	};
+
+	p1v8_bmc_aux: fixedregulator-p1v8-bmc-aux {
+		compatible = "regulator-fixed";
+		regulator-name = "p1v8_bmc_aux";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+};
+
+&adc0 {
+	status = "okay";
+	vref-supply = <&p1v8_bmc_aux>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default
+		&pinctrl_adc1_default
+		&pinctrl_adc2_default
+		&pinctrl_adc3_default
+		&pinctrl_adc4_default
+		&pinctrl_adc5_default
+		&pinctrl_adc6_default
+		&pinctrl_adc7_default>;
+};
+
+&adc1 {
+	status = "okay";
+	vref-supply = <&p1v8_bmc_aux>;
+	aspeed,battery-sensing;
+
+	aspeed,int-vref-microvolt = <2500000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc8_default
+		&pinctrl_adc9_default
+		&pinctrl_adc10_default
+		&pinctrl_adc11_default
+		&pinctrl_adc12_default
+		&pinctrl_adc13_default
+		&pinctrl_adc14_default
+		&pinctrl_adc15_default>;
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&uhci {
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl_gpiol4_unbiased: gpiol4 {
+		pins = "C15";
+		bias-disable;
+	};
+
+	pinctrl_gpiol5_unbiased: gpiol5 {
+		pins = "F15";
+		bias-disable;
+	};
+
+	pinctrl_gpiol6_unbiased: gpiol6 {
+		pins = "B14";
+		bias-disable;
+	};
+
+	pinctrl_gpiol7_unbiased: gpiol7 {
+		pins = "C14";
+		bias-disable;
+	};
+};
+
+&gpio0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpiol4_unbiased
+		&pinctrl_gpiol5_unbiased
+		&pinctrl_gpiol6_unbiased
+		&pinctrl_gpiol7_unbiased>;
+
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","","","",
+	/*B0-B7*/	"","","","","bmc-tpm-reset","","","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"","","","","","","","",
+	/*F0-F7*/	"","","","","","","","",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"","","","","","","","",
+	/*I0-I7*/	"","","","","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","led-bmc-ready",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"pch-reset","","","","","flash-write-override","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"","","","","","","","led-bmc-hb",
+	/*Q0-Q7*/	"","","","","","","pch-ready","",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","","","","","led-rear-enc-fault0","led-rear-enc-id0",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","rtc-battery-voltage-read-enable","","power-chassis-control","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"fpga-pgood","power-chassis-good","pch-pgood","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"","","","","","","","";
+
+	pin-gpio-hog-0 {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(L, 4) GPIO_ACTIVE_HIGH>;
+		input;
+		line-name = "RST_RTCRST_N";
+	};
+
+	pin-gpio-hog-1 {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(L, 5) GPIO_ACTIVE_HIGH>;
+		input;
+		line-name = "RST_SRTCRST_N";
+	};
+
+	pin-gpio-hog-2 {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(L, 6) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "BMC_FAN_E3_SVC_PEX_INT_N";
+	};
+
+	pin-gpio-hog-3 {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(O, 6) GPIO_ACTIVE_LOW>;
+		output-low;
+		line-name = "isolate_errs_cpu1";
+	};
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&pinctrl_emmc_default {
+	bias-disable;
+};
+
+&emmc {
+	status = "okay";
+	clk-phase-mmc-hs200 = <180>, <180>;
+};
+
+&sgpiom0 {
+	status = "okay";
+	ngpios = <128>;
+	bus-frequency = <500000>;
+};
+
+&ibt {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&vuart1 {
+	status = "okay";
+};
+
+&vuart2 {
+	status = "okay";
+};
+
+&lpc_ctrl {
+	status = "okay";
+	memory-region = <&flash_memory>;
+};
+
+&mac2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii3_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>,
+		 <&syscon ASPEED_CLK_MAC3RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
+&mac3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC4CLK>,
+		 <&syscon ASPEED_CLK_MAC4RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
+&wdt1 {
+	aspeed,reset-type = "none";
+	aspeed,external-signal;
+	aspeed,ext-push-pull;
+	aspeed,ext-active-high;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdtrst1_default>;
+};
+
+&wdt2 {
+	status = "okay";
+};
+
+&kcs2 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca8 0xcac>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+	aspeed,lpc-interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&peci0 {
+	status = "okay";
+};
+
+&lpc_snoop {
+	status = "okay";
+	snoop-ports = <0x80>, <0x81>;
+};
+
+&i2c0 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+
+	regulator@42 {
+		compatible = "infineon,ir38263";
+		reg = <0x42>;
+	};
+
+	led-controller@60 {
+		compatible = "nxp,pca9552";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "nic1-perst";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "bmc-perst";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@2 {
+			label = "reset-M2-SSD1-2-perst";
+			reg = <2>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "pcie-perst1";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "pcie-perst2";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "pcie-perst3";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "pcie-perst4";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			label = "pcie-perst5";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			label = "pcie-perst6";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			label = "pcie-perst7";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@10 {
+			label = "pcie-perst8";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@11 {
+			label = "PV-cp0-sw1stk4-perst";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@12 {
+			label = "PV-cp0-sw1stk5-perst";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@13 {
+			label = "pe-cp-drv0-perst";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@14 {
+			label = "pe-cp-drv1-perst";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@15 {
+			label = "lom-perst";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	gpio@74 {
+		compatible = "nxp,pca9539";
+		reg = <0x74>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"PLUG_DETECT_PCIE_J101_N",
+			"PLUG_DETECT_PCIE_J102_N",
+			"PLUG_DETECT_PCIE_J103_N",
+			"PLUG_DETECT_PCIE_J104_N",
+			"PLUG_DETECT_PCIE_J105_N",
+			"PLUG_DETECT_PCIE_J106_N",
+			"PLUG_DETECT_PCIE_J107_N",
+			"PLUG_DETECT_PCIE_J108_N",
+			"PLUG_DETECT_M2_SSD1_N",
+			"PLUG_DETECT_NIC1_N",
+			"SEL_SMB_DIMM_CPU0",
+			"presence-ps2",
+			"presence-ps3",
+			"", "",
+			"PWRBRD_PLUG_DETECT2_N";
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	power-supply@58 {
+		compatible = "intel,crps185";
+		reg = <0x58>;
+	};
+
+	power-supply@59 {
+		compatible = "intel,crps185";
+		reg = <0x59>;
+	};
+
+	power-supply@5a {
+		compatible = "intel,crps185";
+		reg = <0x5a>;
+	};
+
+	power-supply@5b {
+		compatible = "intel,crps185";
+		reg = <0x5b>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c3mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c3mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		i2c3mux0chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c3mux0chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+
+		i2c3mux0chn4: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		i2c3mux0chn5: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		i2c3mux0chn6: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		i2c3mux0chn7: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+&i2c4 {
+	status = "okay";
+	multi-master;
+	bus-frequency = <1000000>;
+
+	ipmb@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+
+		i2c-protocol;
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	regulator@42 {
+		compatible = "infineon,ir38263";
+		reg = <0x42>;
+	};
+
+	regulator@43 {
+		compatible = "infineon,ir38060";
+		reg = <0x43>;
+	};
+};
+
+&i2c6 {
+	status = "okay";
+
+	fan-controller@52 {
+		compatible = "maxim,max31785a";
+		reg = <0x52>;
+	};
+
+	fan-controller@54 {
+		compatible = "maxim,max31785a";
+		reg = <0x54>;
+	};
+
+	eeprom@55 {
+		compatible = "atmel,24c64";
+		reg = <0x55>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c6mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c6mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		i2c6mux0chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c6mux0chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+
+		i2c6mux0chn4: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+
+			humidity-sensor@40 {
+				compatible = "ti,hdc1080";
+				reg = <0x40>;
+			};
+
+			temperature-sensor@48 {
+				compatible = "ti,tmp275";
+				reg = <0x48>;
+			};
+
+			eeprom@50 {
+				compatible = "atmel,24c32";
+				reg = <0x50>;
+			};
+
+			led-controller@60 {
+				compatible = "nxp,pca9551";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gpio-controller;
+				#gpio-cells = <2>;
+
+				led@0 {
+					label = "enclosure-id-led";
+					reg = <0>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@1 {
+					label = "attention-led";
+					reg = <1>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@2 {
+					label = "enclosure-fault-rollup-led";
+					reg = <2>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+
+				led@3 {
+					label = "power-on-led";
+					reg = <3>;
+					retain-state-shutdown;
+					default-state = "keep";
+					type = <PCA955X_TYPE_LED>;
+				};
+			};
+
+			temperature-sensor@76 {
+				compatible = "infineon,dps310";
+				reg = <0x76>;
+			};
+		};
+
+		i2c6mux0chn5: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		i2c6mux0chn6: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		i2c6mux0chn7: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+
+	pca3: gpio@74 {
+		compatible = "nxp,pca9539";
+		reg = <0x74>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	pca4: gpio@77 {
+		compatible = "nxp,pca9539";
+		reg = <0x77>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"PE_NVMED0_EXP_PRSNT_N",
+			"PE_NVMED1_EXP_PRSNT_N",
+			"PE_NVMED2_EXP_PRSNT_N",
+			"PE_NVMED3_EXP_PRSNT_N",
+			"LED_FAULT_NVMED0",
+			"LED_FAULT_NVMED1",
+			"LED_FAULT_NVMED2",
+			"LED_FAULT_NVMED3",
+			"FAN0_PRESENCE_R_N",
+			"FAN1_PRESENCE_R_N",
+			"FAN2_PRESENCE_R_N",
+			"FAN3_PRESENCE_R_N",
+			"FAN4_PRESENCE_R_N",
+			"FAN5_PRESENCE_N",
+			"FAN6_PRESENCE_N",
+			"";
+	};
+};
+
+&i2c7 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c7mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c7mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		i2c7mux0chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c7mux0chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			regulator@58 {
+				compatible = "mps,mp2973";
+				reg = <0x58>;
+			};
+		};
+
+		i2c7mux0chn4: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		i2c7mux0chn5: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+
+			regulator@40 {
+				compatible = "infineon,tda38640";
+				reg = <0x40>;
+			};
+		};
+
+		i2c7mux0chn6: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		i2c7mux0chn7: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+&i2c8 {
+	status = "okay";
+	bus-frequency = <400000>;
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9548";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c8mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			regulator@58 {
+				compatible = "mps,mp2971";
+				reg = <0x58>;
+			};
+		};
+
+		i2c8mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			regulator@40 {
+				compatible = "infineon,tda38640";
+				reg = <0x40>;
+			};
+
+			regulator@41 {
+				compatible = "infineon,tda38640";
+				reg = <0x41>;
+			};
+
+			regulator@58 {
+				compatible = "mps,mp2971";
+				reg = <0x58>;
+			};
+
+			regulator@5b {
+				compatible = "mps,mp2971";
+				reg = <0x5b>;
+			};
+		};
+
+		i2c8mux0chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c8mux0chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+
+		i2c8mux0chn4: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+
+			i2c-mux@70 {
+				compatible = "nxp,pca9548";
+				reg = <0x70>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				i2c-mux-idle-disconnect;
+
+				i2c8mux1chn0: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				i2c8mux1chn1: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				i2c8mux1chn2: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				i2c8mux1chn3: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+
+				i2c8mux1chn4: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+
+				i2c8mux1chn5: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+
+				i2c8mux1chn6: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+
+				i2c8mux1chn7: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+
+		i2c8mux0chn5: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		i2c8mux0chn6: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+
+			temperature-sensor@4c {
+				compatible = "ti,tmp432";
+				reg = <0x4c>;
+			};
+		};
+
+		i2c8mux0chn7: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+
+			regulator@40 {
+				compatible = "infineon,ir38060";
+				reg = <0x40>;
+			};
+		};
+	};
+};
+
+&i2c9 {
+	status = "okay";
+
+	regulator@40 {
+		compatible = "infineon,ir38263";
+		reg = <0x40>;
+	};
+
+	regulator@41 {
+		compatible = "infineon,ir38263";
+		reg = <0x41>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+	};
+};
+
+&i2c11 {
+	status = "okay";
+
+	tpm@2e {
+		compatible = "tcg,tpm-tis-i2c";
+		reg = <0x2e>;
+		memory-region = <&eventlog>;
+	};
+};
+
+&i2c12 {
+	status = "okay";
+};
+
+&i2c13 {
+	status = "okay";
+
+	regulator@41 {
+		compatible = "infineon,ir38263";
+		reg = <0x41>;
+	};
+
+	led-controller@61 {
+		compatible = "nxp,pca9552";
+		reg = <0x61>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		led@0 {
+			label = "efuse-12v-slots";
+			reg = <0>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@1 {
+			label = "efuse-3p3v-slot";
+			reg = <1>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@3 {
+			label = "nic2-pert";
+			reg = <3>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@4 {
+			label = "pcie-perst9";
+			reg = <4>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@5 {
+			label = "pcie-perst10";
+			reg = <5>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@6 {
+			label = "pcie-perst11";
+			reg = <6>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@7 {
+			label = "pcie-perst12";
+			reg = <7>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@8 {
+			label = "pcie-perst13";
+			reg = <8>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@9 {
+			label = "pcie-perst14";
+			reg = <9>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@10 {
+			label = "pcie-perst15";
+			reg = <10>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@11 {
+			label = "pcie-perst16";
+			reg = <11>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@12 {
+			label = "PV-cp1-sw1stk4-perst";
+			reg = <12>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@13 {
+			label = "PV-cp1-sw1stk5-perst";
+			reg = <13>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@14 {
+			label = "pe-cp-drv2-perst";
+			reg = <14>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+
+		led@15 {
+			label = "pe-cp-drv3-perst";
+			reg = <15>;
+			retain-state-shutdown;
+			default-state = "keep";
+			type = <PCA955X_TYPE_LED>;
+		};
+	};
+
+	gpio@75 {
+		compatible = "nxp,pca9539";
+		reg = <0x75>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"PLUG_DETECT_PCIE_J109_N",
+			"PLUG_DETECT_PCIE_J110_N",
+			"PLUG_DETECT_PCIE_J111_N",
+			"PLUG_DETECT_PCIE_J112_N",
+			"PLUG_DETECT_PCIE_J113_N",
+			"PLUG_DETECT_PCIE_J114_N",
+			"PLUG_DETECT_PCIE_J115_N",
+			"PLUG_DETECT_PCIE_J116_N",
+			"PLUG_DETECT_M2_SSD2_N",
+			"PLUG_DETECT_NIC2_N",
+			"SEL_SMB_DIMM_CPU1",
+			"presence-ps0",
+			"presence-ps1",
+			"", "",
+			"PWRBRD_PLUG_DETECT1_N";
+	};
+
+	gpio@76 {
+		compatible = "nxp,pca9539";
+		reg = <0x76>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"SW1_BOOTRCVRYB1_N",
+			"SW1_BOOTRCVRYB0_N",
+			"SW2_BOOTRCVRYB1_N",
+			"SW2_BOOTRCVRYB0_N",
+			"SW3_4_BOOTRCVRYB1_N",
+			"SW3_4_BOOTRCVRYB0_N",
+			"SW5_BOOTRCVRYB1_N",
+			"SW5_BOOTRCVRYB0_N",
+			"SW6_BOOTRCVRYB1_N",
+			"SW6_BOOTRCVRYB0_N",
+			"SW1_RESET_N",
+			"SW3_RESET_N",
+			"SW4_RESET_N",
+			"SW2_RESET_N",
+			"SW5_RESET_N",
+			"SW6_RESET_N";
+	};
+};
+
+&i2c14 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c14mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c14mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		i2c14mux0chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c14mux0chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			regulator@58 {
+				compatible = "mps,mp2973";
+				reg = <0x58>;
+			};
+		};
+
+		i2c14mux0chn4: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		i2c14mux0chn5: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+
+			regulator@40 {
+				compatible = "infineon,tda38640";
+				reg = <0x40>;
+			};
+		};
+
+		i2c14mux0chn6: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		i2c14mux0chn7: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+&i2c15 {
+	status = "okay";
+	bus-frequency = <400000>;
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9548";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c15mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			regulator@58 {
+				compatible = "mps,mp2971";
+				reg = <0x58>;
+			};
+		};
+
+		i2c15mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			regulator@40 {
+				compatible = "infineon,tda38640";
+				reg = <0x40>;
+			};
+
+			regulator@41 {
+				compatible = "infineon,tda38640";
+				reg = <0x41>;
+			};
+
+			regulator@58 {
+				compatible = "mps,mp2971";
+				reg = <0x58>;
+			};
+
+			regulator@5b {
+				compatible = "mps,mp2971";
+				reg = <0x5b>;
+			};
+		};
+
+		i2c15mux0chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c15mux0chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+
+		i2c15mux0chn4: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+
+			i2c-mux@70 {
+				compatible = "nxp,pca9548";
+				reg = <0x70>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				i2c-mux-idle-disconnect;
+
+				i2c15mux1chn0: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				i2c15mux1chn1: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				i2c15mux1chn2: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				i2c15mux1chn3: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+
+				i2c15mux1chn4: i2c@4 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <4>;
+				};
+
+				i2c15mux1chn5: i2c@5 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <5>;
+				};
+
+				i2c15mux1chn6: i2c@6 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <6>;
+				};
+
+				i2c15mux1chn7: i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+				};
+			};
+		};
+
+		i2c15mux0chn5: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		i2c15mux0chn6: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+
+			temperature-sensor@4c {
+				compatible = "ti,tmp432";
+				reg = <0x4c>;
+			};
+		};
+
+		i2c15mux0chn7: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+
+			regulator@40 {
+				compatible = "infineon,ir38060";
+				reg = <0x40>;
+			};
+
+			temperature-sensor@4c {
+				compatible = "ti,tmp432";
+				reg = <0x4c>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-inspur-fp5280g2.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-inspur-fp5280g2.dts
index 60a39ea10ab1..79c6919b3570 100644
--- a/arch/arm/boot/dts/aspeed-bmc-inspur-fp5280g2.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-inspur-fp5280g2.dts
@@ -54,10 +54,9 @@
 	};
 
 	fsi: gpio-fsi {
-		compatible = "aspeed,ast2500-cf-fsi-master", "fsi-master";
+		compatible = "aspeed,ast2500-cf-fsi-master";
 		#address-cells = <2>;
 		#size-cells = <0>;
-		no-gpio-delays;
 
 		memory-region = <&coldfire_memory>;
 		aspeed,sram = <&sram>;
@@ -73,19 +72,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		checkstop {
+		event-checkstop {
 			label = "checkstop";
 			gpios = <&gpio ASPEED_GPIO(B, 3) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(B, 3)>;
 		};
 
-		ps0-presence {
+		event-ps0-presence {
 			label = "ps0-presence";
 			gpios = <&gpio ASPEED_GPIO(F, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(F, 0)>;
 		};
 
-		ps1-presence {
+		event-ps1-presence {
 			label = "ps1-presence";
 			gpios = <&gpio ASPEED_GPIO(F, 1) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(F, 1)>;
@@ -97,49 +96,49 @@
 		compatible = "gpio-keys-polled";
 		poll-interval = <1000>;
 
-		fan0-presence {
+		event-fan0-presence {
 			label = "fan0-presence";
 			gpios = <&pca1 0 GPIO_ACTIVE_LOW>;
 			linux,code = <1>;
 		};
 
-		fan1-presence {
+		event-fan1-presence {
 			label = "fan1-presence";
 			gpios = <&pca1 1 GPIO_ACTIVE_LOW>;
 			linux,code = <2>;
 		};
 
-		fan2-presence {
+		event-fan2-presence {
 			label = "fan2-presence";
 			gpios = <&pca1 2 GPIO_ACTIVE_LOW>;
 			linux,code = <3>;
 		};
 
-		fan3-presence {
+		event-fan3-presence {
 			label = "fan3-presence";
 			gpios = <&pca1 3 GPIO_ACTIVE_LOW>;
 			linux,code = <4>;
 		};
 
-		fan4-presence {
+		event-fan4-presence {
 			label = "fan4-presence";
 			gpios = <&pca1 4 GPIO_ACTIVE_LOW>;
 			linux,code = <5>;
 		};
 
-		fan5-presence {
+		event-fan5-presence {
 			label = "fan5-presence";
 			gpios = <&pca1 5 GPIO_ACTIVE_LOW>;
 			linux,code = <6>;
 		};
 
-		fan6-presence {
+		event-fan6-presence {
 			label = "fan6-presence";
 			gpios = <&pca1 6 GPIO_ACTIVE_LOW>;
 			linux,code = <7>;
 		};
 
-		fan7-presence {
+		event-fan7-presence {
 			label = "fan7-presence";
 			gpios = <&pca1 7 GPIO_ACTIVE_LOW>;
 			linux,code = <8>;
@@ -348,7 +347,7 @@
 		label = "outlet";
 	};
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		reg = <0x70>;
 		#address-cells = <1>;
@@ -432,7 +431,7 @@
 &i2c7 {
 	status = "okay";
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		reg = <0x70>;
 		#address-cells = <1>;
@@ -814,10 +813,6 @@
 	memory-region = <&gfx_memory>;
 };
 
-&pinctrl {
-	aspeed,external-nodes = <&gfx &lhc>;
-};
-
 &wdt1 {
 	aspeed,reset-type = "none";
 	aspeed,external-signal;
diff --git a/arch/arm/boot/dts/aspeed-bmc-inspur-nf5280m6.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-inspur-nf5280m6.dts
index b3c1e3ba5831..92b9b3987c92 100644
--- a/arch/arm/boot/dts/aspeed-bmc-inspur-nf5280m6.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-inspur-nf5280m6.dts
@@ -215,7 +215,7 @@
 		label = "outlet";
 	};
 
-	pca9548@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		reg = <0x70>;
 	};
@@ -224,17 +224,17 @@
 &i2c3 {
 	status = "okay";
 
-	pca9548@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		reg = <0x70>;
 	};
 
-	pca9548@71 {
+	i2c-mux@71 {
 		compatible = "nxp,pca9548";
 		reg = <0x71>;
 	};
 
-	pca9548@72 {
+	i2c-mux@72 {
 		compatible = "nxp,pca9548";
 		reg = <0x72>;
 	};
@@ -248,7 +248,7 @@
 &i2c5 {
 	status = "okay";
 
-	pca9548@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		reg = <0x70>;
 	};
@@ -257,7 +257,7 @@
 &i2c6 {
 	status = "okay";
 
-	pca9548@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		reg = <0x70>;
 	};
diff --git a/arch/arm/boot/dts/aspeed-bmc-inspur-on5263m5.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-inspur-on5263m5.dts
index 5a98a19f445e..7a78c34cff40 100644
--- a/arch/arm/boot/dts/aspeed-bmc-inspur-on5263m5.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-inspur-on5263m5.dts
@@ -123,10 +123,6 @@
 	status = "okay";
 };
 
-&pinctrl {
-	aspeed,external-nodes = <&gfx &lhc>;
-};
-
 &pwm_tacho {
 	status = "okay";
 	pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/aspeed-bmc-intel-s2600wf.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-intel-s2600wf.dts
index d5b7d28cda88..da55e7b29fac 100644
--- a/arch/arm/boot/dts/aspeed-bmc-intel-s2600wf.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-intel-s2600wf.dts
@@ -118,10 +118,6 @@
 	status = "okay";
 };
 
-&pinctrl {
-	aspeed,external-nodes = <&gfx &lhc>;
-};
-
 &pwm_tacho {
 	status = "okay";
 	pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-inventec-starscream.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-inventec-starscream.dts
new file mode 100644
index 000000000000..ec82af94e1fb
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-inventec-starscream.dts
@@ -0,0 +1,389 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2023 Inventec Corp.
+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include "aspeed-g6-pinctrl.dtsi"
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+	model = "STARSCREAM BMC";
+	compatible = "inventec,starscream-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial4 = &uart5;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		video_engine_memory: video {
+			size = <0x04000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-uid {
+			label = "UID_LED";
+			gpios = <&gpio0 186 GPIO_ACTIVE_LOW>;
+		};
+
+		led-heartbeat {
+			label = "HB_LED";
+			gpios = <&gpio0 127 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&mac2 {
+	status = "okay";
+	pinctrl-names = "default";
+	phy-mode = "rmii";
+	pinctrl-0 = <&pinctrl_rmii3_default>;
+	use-ncsi;
+};
+
+&mac3 {
+	status = "okay";
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii4_default>;
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+#include "openbmc-flash-layout.dtsi"
+	};
+
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc2";
+		spi-max-frequency = <50000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bios";
+		spi-max-frequency = <50000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+	};
+};
+
+&vuart1 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&kcs3 {
+	aspeed,lpc-io-reg = <0xca2>;
+	status = "okay";
+};
+
+&uart_routing {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+};
+&i2c1 {
+	status = "okay";
+};
+&i2c2 {
+	status = "okay";
+};
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+
+	// I2C EXPANDER
+	i2c-mux@71 {
+		compatible = "nxp,pca9546";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x71>;
+
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			// AMD SB-TSI CPU1
+			sbtsi@4c {
+				compatible = "amd,sbtsi";
+				reg = <0x4c>;
+			};
+		};
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			// AMD SB-TSI CPU2
+			sbtsi@48 {
+				compatible = "amd,sbtsi";
+				reg = <0x48>;
+			};
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	// I2C EXPANDER U153
+	i2c-mux@70 {
+		compatible = "nxp,pca9546";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+
+		usb_hub: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		riser1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		riser2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&i2c6 {
+	status = "okay";
+
+	// Motherboard Temp_U89
+	temperature-sensor@4e {
+		compatible = "ti,tmp421";
+		reg = <0x4e>;
+	};
+
+	// RunBMC Temp_U6
+	temperature-sensor@49 {
+		compatible = "ti,tmp75";
+		reg = <0x49>;
+	};
+};
+
+&i2c7 {
+	status = "okay";
+	// I2C EXPANDER U40
+	i2c-mux@70 {
+		compatible = "nxp,pca9545";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&i2c8 {
+	status = "okay";
+	// FRU RunBMC
+	eeprom@51 {
+		compatible = "atmel,24c512";
+		reg = <0x51>;
+		pagesize = <128>;
+	};
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+};
+
+&i2c12 {
+	status = "okay";
+	// FRU SCM
+	eeprom@51 {
+		compatible = "atmel,24c512";
+		reg = <0x51>;
+		pagesize = <128>;
+	};
+
+	// SCM Temp_U17
+	temperature-sensor@4f {
+		compatible = "ti,tmp75";
+		reg = <0x4f>;
+	};
+};
+
+&gpio0 {
+	status = "okay";
+	gpio-line-names =
+	/*A0-A7*/   "","","","","","","","",
+	/*B0-B7*/   "alert-psu0-smb-r-n","bmc-ready","","assert-cpu0-prochot-r-n",
+	"","","","",
+	/*C0-C7*/   "","","","","","","","",
+	/*D0-D7*/   "","","","","","","","",
+	/*E0-E7*/   "","","","","","","","",
+	/*F0-F7*/   "","","","","reset-sgpio-r-n","","","",
+	/*G0-G7*/   "","","scm-jtag-mux-select","","","","","",
+	/*H0-H7*/   "","","","","reset-out","power-out","","",
+	/*I0-I7*/   "","","","","","","irq-bmc-cpu0-buf-nmi-n","",
+	/*J0-J7*/   "","","","","","","","",
+	/*K0-K7*/   "","","","","","","","",
+	/*L0-L7*/   "","","","","","","","",
+	/*M0-M7*/   "","","","","","","","",
+	/*N0-N7*/   "","","ncsi-ocp-clk-en-n","","","","","",
+	/*O0-O7*/   "","","","","","","cpu1-thermal-trip-n","",
+	/*P0-P7*/   "","","","","","","","",
+	/*Q0-Q7*/   "cpu0-prochot-n","","cpu1-prochot-n","","cpu0-pe-rst0","","","",
+	/*R0-R7*/   "","","","","","","","",
+	/*S0-S7*/   "","","","",
+	"","PCH_SLP_S4_BMC_N","cpu0-thermtrip-n","alert-psu1-smb-r-n",
+	/*T0-T7*/   "","","","","","","","",
+	/*U0-U7*/   "","","","","","","","",
+	/*V0-V7*/   "bios-recovery-buf-n","","assert-cpu1-prochot-r-n","",
+	"power-chassis-good","","","",
+	/*W0-W7*/   "","","","","","","","",
+	/*X0-X7*/   "","","","","platform-type","","","",
+	/*Y0-Y7*/   "","","","","","","","",
+	/*Z0-Z7*/   "","cpld-power-break-n","","","","","","",
+	/*AA0-AA7*/ "","","","","","","","",
+	/*AB0-AB7*/ "","","","","","","","",
+	/*AC0-AC7*/ "","","","","","","","";
+};
+
+&sgpiom0 {
+	status = "okay";
+	ngpios = <64>;
+	bus-frequency = <1000000>;
+};
+
+&lpc_snoop {
+	status = "okay";
+	snoop-ports = <0x80>;
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&emmc {
+	status = "okay";
+	non-removable;
+	max-frequency = <52000000>;
+	bus-width = <8>;
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+&vhub {
+	status = "okay";
+	aspeed,vhub-downstream-ports = <7>;
+	aspeed,vhub-generic-endpoints = <21>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb2ad_default>;
+};
+
+&rtc {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-inventec-transformers.dts
index caf66651e5b5..c713cb7a6187 100644
--- a/arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-inventec-transformers.dts
@@ -193,14 +193,14 @@
        // I2C EXPANDER
        status = "okay";
 
-       i2c-switch@71 {
+       i2c-mux@71 {
                compatible = "nxp,pca9544";
                #address-cells = <1>;
                #size-cells = <0>;
                reg = <0x71>;
        };
 
-       i2c-switch@73 {
+       i2c-mux@73 {
                compatible = "nxp,pca9544";
                #address-cells = <1>;
                #size-cells = <0>;
@@ -212,7 +212,7 @@
        // I2C EXPANDER
        status = "okay";
 
-       i2c-switch@70 {
+       i2c-mux@70 {
                compatible = "nxp,pca9544";
                #address-cells = <1>;
                #size-cells = <0>;
diff --git a/arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-lenovo-hr630.dts
index 8f543cca7c21..4ad0f44af1ab 100644
--- a/arch/arm/boot/dts/aspeed-bmc-lenovo-hr630.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-lenovo-hr630.dts
@@ -208,7 +208,7 @@
 	 *	Slot 3
 	 */
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9545";
 		reg = <0x70>;
 		#address-cells = <1>;
@@ -249,7 +249,7 @@
 	 *	Slot 2,
 	 *	Slot 3
 	 */
-	i2c-switch@76 {
+	i2c-mux@76 {
 		compatible = "nxp,pca9546";
 		reg = <0x76>;
 		#address-cells = <1>;
@@ -405,161 +405,161 @@
 
 &gpio {
 
-	pin_gpio_b5 {
+	pin-gpio-b5-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(B, 5) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "IRQ_BMC_PCH_SMI_LPC_N";
 	};
 
-	pin_gpio_f0 {
+	pin-gpio-f0-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(F, 0) GPIO_ACTIVE_HIGH>;
 		output-low;
 		line-name = "IRQ_BMC_PCH_NMI_R";
 	};
 
-	pin_gpio_f3 {
+	pin-gpio-f3-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(F, 3) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "I2C_BUS0_RST_OUT_N";
 	};
 
-	pin_gpio_f4 {
+	pin-gpio-f4-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(F, 4) GPIO_ACTIVE_HIGH>;
 		output-low;
 		line-name = "FM_SKT0_FAULT_LED";
 	};
 
-	pin_gpio_f5 {
+	pin-gpio-f5-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(F, 5) GPIO_ACTIVE_HIGH>;
 		output-low;
 		line-name = "FM_SKT1_FAULT_LED";
 	};
 
-	pin_gpio_g4 {
+	pin-gpio-g4-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(G, 4) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "FAN_PWR_CTL_N";
 	};
 
-	pin_gpio_g7 {
+	pin-gpio-g7-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(G, 7) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "RST_BMC_PCIE_I2CMUX_N";
 	};
 
-	pin_gpio_h2 {
+	pin-gpio-h2-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "PSU1_FFS_N_R";
 	};
 
-	pin_gpio_h3 {
+	pin-gpio-h3-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(H, 3) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "PSU2_FFS_N_R";
 	};
 
-	pin_gpio_i3 {
+	pin-gpio-i3-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(I, 3) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "BMC_INTRUDED_COVER";
 	};
 
-	pin_gpio_j2 {
+	pin-gpio-j2-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(J, 2) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "BMC_BIOS_UPDATE_N";
 	};
 
-	pin_gpio_j3 {
+	pin-gpio-j3-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(J, 3) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "RST_BMC_HDD_I2CMUX_N";
 	};
 
-	pin_gpio_s2 {
+	pin-gpio-s2-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(S, 2) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "BMC_VGA_SW";
 	};
 
-	pin_gpio_s4 {
+	pin-gpio-s4-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(S, 4) GPIO_ACTIVE_HIGH>;
 		output;
 		line-name = "VBAT_EN_N";
 	};
 
-	pin_gpio_s6 {
+	pin-gpio-s6-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(S, 6) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "PU_BMC_GPIOS6";
 	};
 
-	pin_gpio_y0 {
+	pin-gpio-y0-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(Y, 0) GPIO_ACTIVE_HIGH>;
 		output-low;
 		line-name = "BMC_NCSI_MUX_CTL_S0";
 	};
 
-	pin_gpio_y1 {
+	pin-gpio-y1-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(Y, 1) GPIO_ACTIVE_HIGH>;
 		output-low;
 		line-name = "BMC_NCSI_MUX_CTL_S1";
 	};
 
-	pin_gpio_z0 {
+	pin-gpio-z0-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(Z, 0) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "I2C_RISER2_INT_N";
 	};
 
-	pin_gpio_z2 {
+	pin-gpio-z2-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(Z, 2) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "I2C_RISER2_RESET_N";
 	};
 
-	pin_gpio_z3 {
+	pin-gpio-z3-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "FM_BMC_PCH_SCI_LPC_N";
 	};
 
-	pin_gpio_z7 {
+	pin-gpio-z7-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(Z, 7) GPIO_ACTIVE_HIGH>;
 		output-low;
 		line-name = "BMC_POST_CMPLT_N";
 	};
 
-	pin_gpio_aa0 {
+	pin-gpio-aa0-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(AA, 0) GPIO_ACTIVE_HIGH>;
 		output-low;
 		line-name = "HOST_BMC_USB_SEL";
 	};
 
-	pin_gpio_aa5 {
+	pin-gpio-aa5-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(AA, 5) GPIO_ACTIVE_HIGH>;
 		output-high;
diff --git a/arch/arm/boot/dts/aspeed-bmc-lenovo-hr855xg2.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-lenovo-hr855xg2.dts
index bcc1820f5c07..fdcf4492fb4e 100644
--- a/arch/arm/boot/dts/aspeed-bmc-lenovo-hr855xg2.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-lenovo-hr855xg2.dts
@@ -151,7 +151,7 @@
 	pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
 };
 
-&adc{
+&adc {
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_adc0_default
@@ -175,7 +175,7 @@
 &i2c0 {
 	status = "okay";
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9545";
 		reg = <0x70>;
 		#address-cells = <1>;
@@ -211,7 +211,7 @@
 	status = "okay";
 	bus-frequency = <90000>;
 	HotSwap@10 {
-		compatible = "adm1272";
+		compatible = "adi,adm1272";
 		reg = <0x10>;
 	};
 
@@ -227,7 +227,7 @@
 
 &i2c3 {
 	status = "okay";
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		reg = <0x70>;
 		#address-cells = <1>;
@@ -425,238 +425,238 @@
 
 &gpio {
 
-	pin_gpio_a1 {
+	pin-gpio-a1-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(A, 1) GPIO_ACTIVE_LOW>;
 		output-high;
 		line-name = "BMC_EMMC_RST_N";
 	};
 
-	pin_gpio_a3 {
+	pin-gpio-a3-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(A, 3) GPIO_ACTIVE_LOW>;
 		output-high;
 		line-name = "PCH_PWROK_BMC_FPGA";
 	};
 
-	pin_gpio_b5 {
+	pin-gpio-b5-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(B, 5) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "IRQ_BMC_PCH_SMI_LPC_N";
 	};
 
-	pin_gpio_b7 {
+	pin-gpio-b7-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(B, 7) GPIO_ACTIVE_LOW>;
 		output-low;
 		line-name = "CPU_SM_WP";
 	};
 
-	pin_gpio_e0 {
+	pin-gpio-e0-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(E, 0) GPIO_ACTIVE_HIGH>;
 		input;
 		line-name = "PDB_PSU_SEL";
 	};
 
-	pin_gpio_e2 {
+	pin-gpio-e2-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(E, 2) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "LOCATOR_LED_N";
 	};
 
-	pin_gpio_e5 {
+	pin-gpio-e5-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(E, 5) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "FM_BMC_DBP_PRESENT_R1_N";
 	};
 
-	pin_gpio_e6 {
+	pin-gpio-e6-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(E, 6) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "BMC_ME_SECURITY_OVERRIDE_N";
 	};
 
-	pin_gpio_f0 {
+	pin-gpio-f0-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(F, 0) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "IRQ_BMC_PCH_NMI_R";
 	};
 
-	pin_gpio_f1 {
+	pin-gpio-f1-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(F, 1) GPIO_ACTIVE_HIGH>;
 		input;
 		line-name = "CPU2_PROCDIS_BMC_N";
 	};
 
-	pin_gpio_f2 {
+	pin-gpio-f2-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(F, 2) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "RM_THROTTLE_EN_N";
 	};
 
-	pin_gpio_f3 {
+	pin-gpio-f3-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(F, 3) GPIO_ACTIVE_HIGH>;
 		output-low;
 		line-name = "FM_PMBUS_ALERT_B_EN";
 	};
 
-	pin_gpio_f4 {
+	pin-gpio-f4-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(F, 4) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "BMC_FORCE_NM_THROTTLE_N";
 	};
 
-	pin_gpio_f6 {
+	pin-gpio-f6-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(F, 6) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "FM_BMC_CPU_PWR_DEBUG_N";
 	};
 
-	pin_gpio_g7 {
+	pin-gpio-g7-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(G, 7) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "BMC_PCIE_I2C_MUX_RST_N";
 	};
 
-	pin_gpio_h6 {
+	pin-gpio-h6-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(H, 6) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "FM_BMC_DBP_PRESENT_R2_N";
 	};
 
-	pin_gpio_i3 {
+	pin-gpio-i3-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(I, 3) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "SPI_BMC_BIOS_WP_N";
 	};
 
-	pin_gpio_j1 {
+	pin-gpio-j1-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(J, 1) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "BMC_USB_SEL";
 	};
 
-	pin_gpio_j2 {
+	pin-gpio-j2-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(J, 2) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "PDB_SMB_RST_N";
 	};
 
-	pin_gpio_j3 {
+	pin-gpio-j3-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(J, 3) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "SPI_BMC_BIOS_HOLD_N";
 	};
 
-	pin_gpio_l0 {
+	pin-gpio-l0-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(L, 0) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "PDB_FAN_TACH_SEL";
 	};
 
-	pin_gpio_l1 {
+	pin-gpio-l1-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(L, 1) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "SYS_RESET_BMC_FPGA_N";
 	};
 
-	pin_gpio_l4 {
+	pin-gpio-l4-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(L, 4) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "FM_EFUSE_FAN_G1_EN";
 	};
 
-	pin_gpio_l5 {
+	pin-gpio-l5-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(L, 5) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "FM_EFUSE_FAN_G2_EN";
 	};
 
-	pin_gpio_r6 {
+	pin-gpio-r6-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(R, 6) GPIO_ACTIVE_HIGH>;
 		input;
 		line-name = "CPU3_PROCDIS_BMC_N";
 	};
 
-	pin_gpio_r7 {
+	pin-gpio-r7-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(R, 7) GPIO_ACTIVE_HIGH>;
 		input;
 		line-name = "CPU4_PROCDIS_BMC_N";
 	};
 
-	pin_gpio_s1 {
+	pin-gpio-s1-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(S, 1) GPIO_ACTIVE_HIGH>;
 		output-low;
 		line-name = "DBP_SYSPWROK_BMC";
 	};
 
-	pin_gpio_s2 {
+	pin-gpio-s2-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(S, 2) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "PCH_RST_RSMRST_N";
 	};
 
-	pin_gpio_s6 {
+	pin-gpio-s6-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(S, 6) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "BMC_HW_STRAP_5";
 	};
 
-	pin_gpio_z3 {
+	pin-gpio-z3-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "FM_BMC_PCH_SCI_LPC_N";
 	};
 
-	pin_gpio_aa0 {
+	pin-gpio-aa0-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(AA, 0) GPIO_ACTIVE_HIGH>;
 		output-low;
 		line-name = "FW_PSU_ALERT_EN_N";
 	};
 
-	pin_gpio_aa4 {
+	pin-gpio-aa4-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(AA, 4) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "DBP_CPU_PREQ_N";
 	};
 
-	pin_gpio_ab3 {
+	pin-gpio-ab3-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(AB, 3) GPIO_ACTIVE_HIGH>;
 		output-low;
 		line-name = "BMC_WDTRST";
 	};
 
-	pin_gpio_ac6 {
+	pin-gpio-ac6-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(AC, 6) GPIO_ACTIVE_HIGH>;
 		output-high;
diff --git a/arch/arm/boot/dts/aspeed-bmc-microsoft-olympus.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-microsoft-olympus.dts
index 3ef8358ff764..3ef8358ff764 100644
--- a/arch/arm/boot/dts/aspeed-bmc-microsoft-olympus.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-microsoft-olympus.dts
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dts
new file mode 100644
index 000000000000..4de38613b0ea
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-nvidia-gb200nvl-bmc.dts
@@ -0,0 +1,1178 @@
+// SPDX-License-Identifier: GPL-2.0+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "AST2600 GB200NVL BMC";
+	compatible = "nvidia,gb200nvl-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial2 = &uart3;
+		serial4 = &uart5;
+		i2c16   = &imux16;
+		i2c17   = &imux17;
+		i2c18   = &imux18;
+		i2c19   = &imux19;
+		i2c20   = &imux20;
+		i2c21   = &imux21;
+		i2c22   = &imux22;
+		i2c23   = &imux23;
+		i2c24   = &imux24;
+		i2c25   = &imux25;
+		i2c26   = &imux26;
+		i2c27   = &imux27;
+		i2c28   = &imux28;
+		i2c29   = &imux29;
+		i2c30   = &imux30;
+		i2c31   = &imux31;
+		i2c32   = &imux32;
+		i2c33   = &imux33;
+		i2c34   = &imux34;
+		i2c35   = &imux35;
+		i2c36   = &imux36;
+		i2c37   = &imux37;
+		i2c38   = &imux38;
+		i2c39   = &imux39;
+		i2c40	= &e1si2c0;
+		i2c41	= &e1si2c1;
+		i2c42	= &e1si2c2;
+		i2c43	= &e1si2c3;
+		i2c44	= &e1si2c4;
+		i2c45	= &e1si2c5;
+		i2c46	= &e1si2c6;
+		i2c47	= &e1si2c7;
+		i2c48	= &i2c17mux0;
+		i2c49	= &i2c17mux1;
+		i2c50	= &i2c17mux2;
+		i2c51	= &i2c17mux3;
+		i2c52	= &i2c25mux0;
+		i2c53	= &i2c25mux1;
+		i2c54	= &i2c25mux2;
+		i2c55	= &i2c25mux3;
+		i2c56	= &i2c29mux0;
+		i2c57	= &i2c29mux1;
+		i2c58	= &i2c29mux2;
+		i2c59	= &i2c29mux3;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		vga_memory: framebuffer@9f000000 {
+			no-map;
+			reg = <0x9f000000 0x01000000>; /* 16M */
+		};
+
+		ramoops@a0000000 {
+			compatible = "ramoops";
+			reg = <0xa0000000 0x100000>; /* 1MB */
+			record-size = <0x10000>; /* 64KB */
+			max-reason = <2>; /* KMSG_DUMP_OOPS */
+		};
+
+		gfx_memory: framebuffer {
+			size = <0x01000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+
+		video_engine_memory: jpegbuffer {
+			size = <0x02000000>;	/* 32M */
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-0 {
+			label = "uid_led";
+			gpios = <&sgpiom0 27 GPIO_ACTIVE_LOW>;
+		};
+		led-1 {
+			label = "fault_led";
+			gpios = <&sgpiom0 29 GPIO_ACTIVE_LOW>;
+		};
+		led-2 {
+			label = "power_led";
+			gpios = <&sgpiom0 31 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	buttons {
+		button-power {
+			label = "power-btn";
+			gpio = <&sgpiom0 156 GPIO_ACTIVE_LOW>;
+		};
+		button-uid {
+			label = "uid-btn";
+			gpio = <&sgpiom0 154 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	standby_power_regulator: standby-power-regulator {
+		status = "okay";
+		compatible = "regulator-fixed";
+		regulator-name = "standby_power";
+		gpio = <&gpio0 ASPEED_GPIO(M, 3) GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		enable-active-high;
+		regulator-always-on;
+	};
+};
+
+// Enable Primary flash on FMC for bring up activity
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		compatible = "jedec,spi-nor";
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			u-boot@0 {
+				// 896KB
+				reg = <0x0 0xe0000>;
+				label = "u-boot";
+			};
+
+			kernel@100000 {
+				// 9MB
+				reg = <0x100000 0x900000>;
+				label = "kernel";
+			};
+
+			rofs@a00000 {
+				// 55292KB (extends to end of 64MB SPI - 4KB)
+				reg = <0xa00000 0x35FF000>;
+				label = "rofs";
+			};
+		};
+	};
+};
+
+&spi2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi2_default>;
+
+	// Data SPI is 64MB in size
+	flash@0 {
+		status = "okay";
+		label = "config";
+		spi-max-frequency = <50000000>;
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			u-boot-env@0 {
+				// 256KB
+				reg = <0x0 0x40000>;
+				label = "u-boot-env";
+			};
+
+			rwfs@40000 {
+				// 16MB
+				reg = <0x40000 0x1000000>;
+				label = "rwfs";
+			};
+
+			log@1040000 {
+				// 40MB
+				reg = <0x1040000 0x2800000>;
+				label = "log";
+			};
+		};
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart3 {
+	// Enabling SOL
+	status = "okay";
+};
+
+&uart5 {
+	// BMC Debug Console
+	status = "okay";
+};
+
+&uart_routing {
+	status = "okay";
+};
+
+&mdio0 {
+	status = "okay";
+	ethphy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mdio3 {
+	status = "okay";
+	ethphy3: ethernet-phy@2 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <2>;
+	};
+};
+
+&mac0 {
+	status = "okay";
+	pinctrl-names = "default";
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy3>;
+	pinctrl-0 = <&pinctrl_rgmii1_default>;
+};
+
+&mac2 {
+	status = "okay";
+	phy-mode = "rmii";
+	use-ncsi;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii3_default>;
+};
+
+/*
+ * Enable USB port A as device (via the virtual hub) to host
+ */
+&vhub {
+	status = "okay";
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+// USB 2.0 to HMC, on USB Port B
+&ehci1 {
+	status = "okay";
+};
+
+// USB 1.0
+&uhci {
+	status = "okay";
+};
+
+&sgpiom0 {
+	status = "okay";
+	ngpios = <128>;
+	gpio-line-names =
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"RUN_POWER_FAULT_L-I","SYS_RST_IN_L-O",
+		"RUN_POWER_PG-I","PWR_BRAKE_L-O",
+		"SYS_RST_OUT_L-I","RUN_POWER_EN-O",
+		"L0L1_RST_REQ_OUT_L-I","SHDN_FORCE_L-O",
+		"L2_RST_REQ_OUT_L-I","SHDN_REQ_L-O",
+		"SHDN_OK_L-I","UID_LED_N-O",
+		"BMC_I2C1_FPGA_ALERT_L-I","SYS_FAULT_LED_N-O",
+		"BMC_I2C0_FPGA_ALERT_L-I","PWR_LED_N-O",
+		"FPGA_RSVD_FFU3-I","",
+		"FPGA_RSVD_FFU2-I","",
+		"FPGA_RSVD_FFU1-I","",
+		"FPGA_RSVD_FFU0-I","BMC_I2C_SSIF_ALERT_L-O",
+		"CPU_BOOT_DONE-I","JTAG_MUX_SELECT-O",
+		"SPI_BMC_FPGA_INT_L-I","RTC_CLR_L-O",
+		"THERM_BB_WARN_L-I","UART_MUX_SEL-O",
+		"THERM_BB_OVERT_L-I","",
+		"CPU0_UPHY3_PRSNT1_L-I","IOBRD0_RUN_POWER_EN-O",
+		"CPU0_UPHY3_PRSNT0_L-I","IOBRD1_RUN_POWER_EN-O",
+		"CPU0_UPHY2_PRSNT1_L-I","FPGA_RSVD_FFU4-O",
+		"CPU0_UPHY2_PRSNT0_L-I","FPGA_RSVD_FFU5-O",
+		"CPU0_UPHY1_PRSNT1_L-I","FPGA_RSVD_FFU6-O",
+		"CPU0_UPHY1_PRSNT0_L-I","FPGA_RSVD_FFU7-O",
+		"CPU0_UPHY0_PRSNT1_L-I","RSVD_NV_PLT_DETECT-O",
+		"CPU0_UPHY0_PRSNT0_L-I","SPI1_INT_L-O",
+		"CPU1_UPHY3_PRSNT1_L-I","",
+		"CPU1_UPHY3_PRSNT0_L-I","HMC_EROT_MUX_STATUS",
+		"CPU1_UPHY2_PRSNT1_L-I","",
+		"CPU1_UPHY2_PRSNT0_L-I","",
+		"CPU1_UPHY1_PRSNT1_L-I","",
+		"CPU1_UPHY1_PRSNT0_L-I","",
+		"CPU1_UPHY0_PRSNT1_L-I","",
+		"CPU1_UPHY0_PRSNT0_L-I","",
+		"FAN1_PRESENT_L-I","",
+		"FAN0_PRESENT_L-I","",
+		"","",
+		"IPEX_CABLE_PRSNT_L-I","",
+		"M2_1_PRSNT_L-I","",
+		"M2_0_PRSNT_L-I","",
+		"CPU1_UPHY4_PRSNT1_L-I","",
+		"CPU0_UPHY4_PRSNT0_L-I","",
+		"","",
+		"I2C_RTC_ALERT_L-I","",
+		"FAN7_PRESENT_L-I","",
+		"FAN6_PRESENT_L-I","",
+		"FAN5_PRESENT_L-I","",
+		"FAN4_PRESENT_L-I","",
+		"FAN3_PRESENT_L-I","",
+		"FAN2_PRESENT_L-I","",
+		"IOBRD0_IOX_INT_L-I","",
+		"IOBRD1_PRSNT_L-I","",
+		"IOBRD0_PRSNT_L-I","",
+		"IOBRD1_PWR_GOOD-I","",
+		"IOBRD0_PWR_GOOD-I","",
+		"","",
+		"","",
+		"FAN_FAIL_IN_L-I","",
+		"","",
+		"","",
+		"","",
+		"PDB_CABLE_PRESENT_L-I","",
+		"","",
+		"CHASSIS_PWR_BRK_L-I","",
+		"","",
+		"IOBRD1_IOX_INT_L-I","",
+		"10GBE_SMBALRT_L-I","",
+		"PCIE_WAKE_L-I","",
+		"I2C_M21_ALERT_L-I","",
+		"I2C_M20_ALERT_L-I","",
+		"TRAY_FAST_SHDN_L-I","",
+		"UID_BTN_N-I","",
+		"PWR_BTN_L-I","",
+		"PSU_SMB_ALERT_L-I","",
+		"","",
+		"","",
+		"NODE_LOC_ID[0]-I","",
+		"NODE_LOC_ID[1]-I","",
+		"NODE_LOC_ID[2]-I","",
+		"NODE_LOC_ID[3]-I","",
+		"NODE_LOC_ID[4]-I","",
+		"NODE_LOC_ID[5]-I","",
+		"FAN10_PRESENT_L-I","",
+		"FAN9_PRESENT_L-I","",
+		"FAN8_PRESENT_L-I","",
+		"FPGA1_READY_HMC-I","",
+		"DP_HPD-I","",
+		"HMC_I2C3_FPGA_ALERT_L-I","",
+		"HMC_I2C2_FPGA_ALERT_L-I","",
+		"FPGA0_READY_HMC-I","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"LEAK_DETECT_ALERT_L-I","",
+		"MOD1_B2B_CABLE_PRESENT_L-I","",
+		"MOD1_CLINK_CABLE_PRESENT_L-I","",
+		"FAN11_PRESENT_L-I","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"","",
+		"RSVD_SGPIO_IN_CRC[0]","RSVD_SGPIO_O_CRC[7]",
+		"RSVD_SGPIO_IN_CRC[1]","RSVD_SGPIO_O_CRC[6]",
+		"RSVD_SGPIO_IN_CRC[2]","RSVD_SGPIO_O_CRC[5]",
+		"RSVD_SGPIO_IN_CRC[3]","RSVD_SGPIO_O_CRC[4]",
+		"RSVD_SGPIO_IN_CRC[4]","RSVD_SGPIO_O_CRC[3]",
+		"RSVD_SGPIO_IN_CRC[5]","RSVD_SGPIO_O_CRC[2]",
+		"RSVD_SGPIO_IN_CRC[6]","RSVD_SGPIO_O_CRC[1]",
+		"RSVD_SGPIO_IN_CRC[7]","RSVD_SGPIO_O_CRC[0]";
+};
+
+// I2C1, SSIF IPMI interface
+&i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ssif-bmc@10 {
+		compatible = "ssif-bmc";
+		reg = <0x10>;
+	};
+};
+
+// I2C2
+// BMC_I2C1_FPGA - Secondary FPGA
+// HMC EROT
+&i2c1 {
+	status = "okay";
+	clock-frequency = <400000>;
+	multi-master;
+};
+
+// I2C3
+// BMC_I2C0_FPGA - Primary FPGA
+// HMC FRU EEPROM
+&i2c2 {
+	status = "okay";
+	clock-frequency = <400000>;
+	multi-master;
+};
+
+// I2C4
+&i2c3 {
+	status = "okay";
+};
+
+// I2C5
+// RTC Driver
+// IO Expander
+&i2c4 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	// Module 0, Expander @0x21
+	exp4: gpio@21 {
+		compatible = "nxp,pca9555";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
+		vcc-supply = <&standby_power_regulator>;
+		gpio-line-names =
+			"RTC_MUX_SEL-O",
+			"PCI_MUX_SEL-O",
+			"TPM_MUX_SEL-O",
+			"FAN_MUX-SEL-O",
+			"SGMII_MUX_SEL-O",
+			"DP_MUX_SEL-O",
+			"UPHY3_USB_SEL-O",
+			"NCSI_MUX_SEL-O",
+			"BMC_PHY_RST-O",
+			"RTC_CLR_L-O",
+			"BMC_12V_CTRL-O",
+			"PS_RUN_IO0_PG-I",
+			"",
+			"",
+			"",
+			"";
+	};
+};
+
+// I2C6
+// Module 0/1 I2C MUX x3
+&i2c5 {
+	status = "okay";
+	clock-frequency = <400000>;
+	multi-master;
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9546";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x71>;
+		i2c-mux-idle-disconnect;
+		vdd-supply = <&standby_power_regulator>;
+
+		imux16: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux17: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			i2c-mux@74 {
+				compatible = "nxp,pca9546";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x74>;
+				i2c-mux-idle-disconnect;
+
+				i2c17mux0: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				i2c17mux1: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				i2c17mux2: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				i2c17mux3: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+			};
+		};
+
+		imux18: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux19: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+
+	i2c-mux@72 {
+		compatible = "nxp,pca9546";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x72>;
+		i2c-mux-idle-disconnect;
+		vdd-supply = <&standby_power_regulator>;
+
+		imux20: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux21: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			gpio@21 {
+				compatible = "nxp,pca9555";
+				reg = <0x21>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				vcc-supply = <&standby_power_regulator>;
+				gpio-line-names =
+					"RST_CX_0_L-O",
+					"RST_CX_1_L-O",
+					"CX0_SSD0_PRSNT_L-I",
+					"CX1_SSD1_PRSNT_L-I",
+					"CX_BOOT_CMPLT_CX0-I",
+					"CX_BOOT_CMPLT_CX1-I",
+					"CX_TWARN_CX0_L-I",
+					"CX_TWARN_CX1_L-I",
+					"CX_OVT_SHDN_CX0-I",
+					"CX_OVT_SHDN_CX1-I",
+					"FNP_L_CX0-O",
+					"FNP_L_CX1-O",
+					"",
+					"MCU_GPIO-I",
+					"MCU_RST_N-O",
+					"MCU_RECOVERY_N-O";
+			};
+		};
+
+		imux22: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux23: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+
+	i2c-mux@73 {
+		compatible = "nxp,pca9546";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x73>;
+		i2c-mux-idle-disconnect;
+		vdd-supply = <&standby_power_regulator>;
+
+		imux24: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux25: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			i2c-mux@70 {
+				compatible = "nxp,pca9546";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x70>;
+				i2c-mux-idle-disconnect;
+				vdd-supply = <&standby_power_regulator>;
+
+				i2c25mux0: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				i2c25mux1: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				i2c25mux2: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				i2c25mux3: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+			};
+		};
+
+		imux26: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux27: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+
+	i2c-mux@75 {
+		compatible = "nxp,pca9546";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		i2c-mux-idle-disconnect;
+		vdd-supply = <&standby_power_regulator>;
+
+		imux28: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux29: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			i2c-mux@74 {
+				compatible = "nxp,pca9546";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x74>;
+				i2c-mux-idle-disconnect;
+
+				i2c29mux0: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				i2c29mux1: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				i2c29mux2: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				i2c29mux3: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+				};
+			};
+		};
+
+		imux30: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux31: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+
+	i2c-mux@76 {
+		compatible = "nxp,pca9546";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x76>;
+		i2c-mux-idle-disconnect;
+		vdd-supply = <&standby_power_regulator>;
+
+		imux32: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux33: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			gpio@21 {
+				compatible = "nxp,pca9555";
+				reg = <0x21>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				vcc-supply = <&standby_power_regulator>;
+				gpio-line-names =
+					"SEC_RST_CX_0_L-O",
+					"SEC_RST_CX_1_L-O",
+					"SEC_CX0_SSD0_PRSNT_L-I",
+					"SEC_CX1_SSD1_PRSNT_L-I",
+					"SEC_CX_BOOT_CMPLT_CX0-I",
+					"SEC_CX_BOOT_CMPLT_CX1-I",
+					"SEC_CX_TWARN_CX0_L-I",
+					"SEC_CX_TWARN_CX1_L-I",
+					"SEC_CX_OVT_SHDN_CX0-I",
+					"SEC_CX_OVT_SHDN_CX1-I",
+					"SEC_FNP_L_CX0-O",
+					"SEC_FNP_L_CX1-O",
+					"",
+					"SEC_MCU_GPIO-I",
+					"SEC_MCU_RST_N-O",
+					"SEC_MCU_RECOVERY_N-O";
+				};
+		};
+
+		imux34: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux35: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+
+	i2c-mux@77 {
+		compatible = "nxp,pca9546";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x77>;
+		i2c-mux-idle-disconnect;
+		vdd-supply = <&standby_power_regulator>;
+
+		imux36: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux37: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		imux38: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux39: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+// I2C7
+// Module 0/1 Leak Sensors
+// Module 0/1 Fan Controllers
+&i2c6 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	pmic@12 {
+		compatible = "ti,lm5066i";
+		reg = <0x12>;
+		shunt-resistor-micro-ohms = <190>;
+		status = "okay";
+	};
+
+	pmic@14 {
+		compatible = "ti,lm5066i";
+		reg = <0x14>;
+		shunt-resistor-micro-ohms = <190>;
+		status = "okay";
+	};
+
+	pwm@20 {
+		compatible = "maxim,max31790";
+		reg = <0x20>;
+	};
+
+	pwm@23 {
+		compatible = "maxim,max31790";
+		reg = <0x23>;
+	};
+
+	pwm@2c {
+		compatible = "maxim,max31790";
+		reg = <0x2c>;
+	};
+
+	pwm@2f {
+		compatible = "maxim,max31790";
+		reg = <0x2f>;
+	};
+};
+
+// I2C9
+// M.2
+&i2c8 {
+	status = "okay";
+	clock-frequency = <400000>;
+	multi-master;
+};
+
+// I2C10
+// HMC IO Expander
+// Module 0/1 IO Expanders
+&i2c9 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	// Module 0, Expander @0x20
+	exp0: gpio@20 {
+		compatible = "nxp,pca9555";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
+		vcc-supply = <&standby_power_regulator>;
+		gpio-line-names =
+			"FPGA_THERM_OVERT_L-I",
+			"FPGA_READY_BMC-I",
+			"HMC_BMC_DETECT-O",
+			"HMC_PGOOD-O",
+			"",
+			"BMC_STBY_CYCLE-O",
+			"FPGA_EROT_FATAL_ERROR_L-I",
+			"WP_HW_EXT_CTRL_L-O",
+			"EROT_FPGA_RST_L-O",
+			"FPGA_EROT_RECOVERY_L-O",
+			"BMC_EROT_FPGA_SPI_MUX_SEL-O",
+			"USB_HUB_RESET_L-O",
+			"NCSI_CS1_SEL-O",
+			"SGPIO_EN_L-O",
+			"B2B_IOEXP_INT_L-I",
+			"I2C_BUS_MUX_RESET_L-O";
+	};
+
+	// Module 1, Expander @0x21
+	exp1: gpio@21 {
+		compatible = "nxp,pca9555";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
+		vcc-supply = <&standby_power_regulator>;
+		gpio-line-names =
+			"SEC_FPGA_THERM_OVERT_L-I",
+			"SEC_FPGA_READY_BMC-I",
+			"",
+			"",
+			"",
+			"",
+			"SEC_FPGA_EROT_FATAL_ERROR_L-I",
+			"SEC_WP_HW_EXT_CTRL_L-O",
+			"SEC_EROT_FPGA_RST_L-O",
+			"SEC_FPGA_EROT_RECOVERY_L-O",
+			"SEC_BMC_EROT_FPGA_SPI_MUX_SEL-O",
+			"SEC_USB2_HUB_RST_L-O",
+			"",
+			"",
+			"",
+			"SEC_I2C_BUS_MUX_RESET_L-O";
+	};
+
+	// HMC Expander @0x27
+	exp2: gpio@27 {
+		compatible = "nxp,pca9555";
+		reg = <0x27>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
+		gpio-line-names =
+			"HMC_PRSNT_L-I",
+			"HMC_READY-I",
+			"HMC_EROT_FATAL_ERROR_L-I",
+			"I2C_MUX_SEL-O",
+			"HMC_EROT_SPI_MUX_SEL-O",
+			"HMC_EROT_RECOVERY_L-O",
+			"HMC_EROT_RST_L-O",
+			"GLOBAL_WP_HMC-O",
+			"FPGA_RST_L-O",
+			"USB2_HUB_RST-O",
+			"CPU_UART_MUX_SEL-O",
+			"",
+			"",
+			"",
+			"",
+			"";
+	};
+
+	// HMC Expander @0x74
+	exp3: gpio@74 {
+		compatible = "nxp,pca9555";
+		reg = <0x74>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <ASPEED_GPIO(B, 6) IRQ_TYPE_LEVEL_LOW>;
+		vcc-supply = <&standby_power_regulator>;
+		gpio-line-names =
+			"IOB_PRSNT_L",
+			"IOB_DP_HPD",
+			"IOX_BMC_RESET",
+			"IOB_IOEXP_INT_L",
+			"IOB_UID_LED_L",
+			"IOB_UID_BTN_L",
+			"IOB_SYS_RST_BTN_L",
+			"IOB_PWR_LED_L",
+			"IOB_PWR_BTN_L",
+			"IOB_PHY_RST",
+			"CPLD_JTAG_MUX_SEL",
+			"",
+			"",
+			"",
+			"",
+			"";
+	};
+};
+
+// I2C11
+// BMC FRU EEPROM
+// BMC Temp Sensor
+&i2c10 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	// BMC FRU EEPROM - 256 bytes
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <8>;
+	};
+};
+
+// I2C12
+&i2c11 {
+	status = "disabled";
+};
+
+// I2C13
+&i2c12 {
+	status = "disabled";
+};
+
+// I2C14
+// Module 0 UPHY3 SMBus
+&i2c13 {
+	status = "disabled";
+};
+
+// I2C15
+// Module 1 UPHY3 SMBus
+&i2c14 {
+	status = "okay";
+	clock-frequency = <100000>;
+	multi-master;
+
+	//E1.S drive slot 0-3
+	i2c-mux@77 {
+		compatible = "nxp,pca9546";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x77>;
+		i2c-mux-idle-disconnect;
+		vdd-supply = <&standby_power_regulator>;
+
+		e1si2c0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		e1si2c1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		e1si2c2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		e1si2c3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+// I2C16
+&i2c15 {
+	status = "okay";
+	clock-frequency = <100000>;
+	multi-master;
+
+	//E1.S drive slot 4-7
+	i2c-mux@77 {
+		compatible = "nxp,pca9546";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x77>;
+		i2c-mux-idle-disconnect;
+		vdd-supply = <&standby_power_regulator>;
+
+		e1si2c4: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		e1si2c5: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		e1si2c6: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		e1si2c7: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&rng {
+	status = "okay";
+};
+
+&gpio0 {
+	gpio-line-names =
+		/*A0-A7*/ "", "", "", "", "", "", "", "",
+		/*B0-B7*/ "", "", "", "", "", "", "", "",
+		/*C0-C7*/ "SGPIO_I2C_MUX_SEL-O", "", "", "", "", "", "", "",
+		/*D0-D7*/ "", "", "", "UART1_MUX_SEL-O", "", "FPGA_PEX_RST_L-O", "", "",
+		/*E0-E7*/ "RTL8221_PHY_RST_L-O", "RTL8211_PHY_INT_L-I",	"", "UART3_MUX_SEL-O",
+					"", "", "", "SGPIO_BMC_EN-O",
+		/*F0-F7*/ "", "", "", "", "", "", "", "",
+		/*G0-G7*/ "", "", "", "", "", "", "", "",
+		/*H0-H7*/ "", "", "", "", "", "", "", "",
+		/*I0-I7*/ "", "", "", "", "", "QSPI2_RST_L-O", "GLOBAL_WP_BMC-O", "BMC_DDR4_TEN-O",
+		/*J0-J7*/ "", "", "", "", "", "", "", "",
+		/*K0-K7*/ "", "", "", "", "", "", "", "",
+		/*L0-L7*/ "", "", "", "", "", "", "", "",
+		/*M0-M7*/ "PCIE_EP_RST_EN-O", "BMC_FRU_WP-O", "FPGA_RST_L-O", "STBY_POWER_EN-O",
+					"STBY_POWER_PG-I", "PCIE_EP_RST_L-O", "", "",
+		/*N0-N7*/ "", "", "", "", "", "", "", "",
+		/*O0-O7*/ "", "", "", "", "", "", "", "",
+		/*P0-P7*/ "", "", "", "", "", "", "", "",
+		/*Q0-Q7*/ "", "", "", "", "", "", "", "",
+		/*R0-R7*/ "", "", "", "", "", "", "", "",
+		/*S0-S7*/ "", "", "", "", "", "", "", "",
+		/*T0-T7*/ "", "", "", "", "", "", "", "",
+		/*U0-U7*/ "", "", "", "", "", "", "", "",
+		/*V0-V7*/ "AP_EROT_REQ-O", "EROT_AP_GNT-I", "", "","PCB_TEMP_ALERT-I", "","", "",
+		/*W0-W7*/ "", "", "", "", "", "", "", "",
+		/*X0-X7*/ "", "", "TPM_MUX_SEL-O", "", "", "", "", "",
+		/*Y0-Y7*/ "", "", "", "EMMC_RST-O", "","", "", "",
+		/*Z0-Z7*/ "BMC_READY-O","", "", "", "", "", "", "";
+};
+
+&gpio1 {
+	/* 36 1.8V GPIOs */
+	gpio-line-names =
+		/*A0-A7*/ "", "", "", "", "", "", "", "",
+		/*B0-B7*/ "", "", "", "", "", "", "IO_EXPANDER_INT_L-I","",
+		/*C0-C7*/ "", "", "", "", "", "", "", "",
+		/*D0-D7*/ "", "", "", "", "", "", "SPI_HOST_TPM_RST_L-O", "SPI_BMC_FPGA_INT_L-I",
+		/*E0-E7*/ "", "", "", "", "", "", "", "";
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-lanyang.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-lanyang.dts
index c0847636f20b..9f2ad551255d 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-lanyang.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-lanyang.dts
@@ -52,18 +52,18 @@
 			gpios = <&gpio ASPEED_GPIO(B, 3) GPIO_ACTIVE_HIGH>;
 		};
 		bmc_err {
-			lable = "BMC_fault";
+			label = "BMC_fault";
 			gpios = <&gpio ASPEED_GPIO(H, 6) GPIO_ACTIVE_HIGH>;
 		};
 
 		sys_err {
-			lable = "Sys_fault";
+			label = "Sys_fault";
 			gpios = <&gpio ASPEED_GPIO(H, 7) GPIO_ACTIVE_HIGH>;
 		};
 	};
 
 	fsi: gpio-fsi {
-		compatible = "fsi-master-gpio", "fsi-master";
+		compatible = "fsi-master-gpio";
 		#address-cells = <2>;
 		#size-cells = <0>;
 
@@ -263,54 +263,50 @@
 	status = "okay";
 };
 
-&pinctrl {
-	aspeed,external-nodes = <&gfx &lhc>;
-};
-
 &gpio {
-	pin_gpio_b0 {
+	pin-gpio-b0-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(B, 0) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "BMC_HDD1_PWR_EN";
 	};
 
-	pin_gpio_b5 {
+	pin-gpio-b5-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(B, 5) GPIO_ACTIVE_HIGH>;
 		input;
 		line-name = "BMC_USB1_OCI2";
 	};
 
-	pin_gpio_h5 {
+	pin-gpio-h5-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(H, 5) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "BMC_CP0_PERST_ENABLE_R";
 	};
 
-	pin_gpio_z2 {
+	pin-gpio-z2-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(Z, 2) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "RST_PCA9546_U177_N";
 	};
 
-	pin_gpio_aa6 {
+	pin-gpio-aa6-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(AA, 6) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "BMC_CP0_RESET_N";
 	};
 
-	pin_gpio_aa7 {
+	pin-gpio-aa7-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(AA, 7) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "BMC_TPM_RESET_N";
 	};
 
-	pin_gpio_ab0 {
+	pin-gpio-ab0-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(AB, 0) GPIO_ACTIVE_LOW>;
 		output-high;
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-mowgli.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-mowgli.dts
index 7d38d121ec6d..6c8b966ffccc 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-mowgli.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-mowgli.dts
@@ -46,31 +46,31 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		air-water {
+		event-air-water {
 			label = "air-water";
 			gpios = <&gpio ASPEED_GPIO(F, 6) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(F, 6)>;
 		};
 
-		checkstop {
+		event-checkstop {
 			label = "checkstop";
 			gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(J, 2)>;
 		};
 
-		ps0-presence {
+		event-ps0-presence {
 			label = "ps0-presence";
 			gpios = <&gpio ASPEED_GPIO(Z, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(Z, 2)>;
 		};
 
-		ps1-presence {
+		event-ps1-presence {
 			label = "ps1-presence";
 			gpios = <&gpio ASPEED_GPIO(Z, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(Z, 0)>;
 		};
 
-		id-button {
+		button-id {
 			label = "id-button";
 			gpios = <&gpio ASPEED_GPIO(F, 1) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(F, 1)>;
@@ -81,31 +81,31 @@
 		compatible = "gpio-keys-polled";
 		poll-interval = <1000>;
 
-		fan0-presence {
+		event-fan0-presence {
 			label = "fan0-presence";
 			gpios = <&pca9552 9 GPIO_ACTIVE_LOW>;
 			linux,code = <9>;
 		};
 
-		fan1-presence {
+		event-fan1-presence {
 			label = "fan1-presence";
 			gpios = <&pca9552 10 GPIO_ACTIVE_LOW>;
 			linux,code = <10>;
 		};
 
-		fan2-presence {
+		event-fan2-presence {
 			label = "fan2-presence";
 			gpios = <&pca9552 11 GPIO_ACTIVE_LOW>;
 			linux,code = <11>;
 		};
 
-		fan3-presence {
+		event-fan3-presence {
 			label = "fan3-presence";
 			gpios = <&pca9552 12 GPIO_ACTIVE_LOW>;
 			linux,code = <12>;
 		};
 
-		fan4-presence {
+		event-fan4-presence {
 			label = "fan4-presence";
 			gpios = <&pca9552 13 GPIO_ACTIVE_LOW>;
 			linux,code = <13>;
@@ -165,7 +165,7 @@
 	};
 
 	fsi: gpio-fsi {
-		compatible = "fsi-master-gpio", "fsi-master";
+		compatible = "fsi-master-gpio";
 		#address-cells = <2>;
 		#size-cells = <0>;
 		no-gpio-delays;
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-nicole.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-nicole.dts
index 3d4bdad27c2d..ce6d30ddf07c 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-nicole.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-nicole.dts
@@ -77,10 +77,9 @@
 	};
 
 	fsi: gpio-fsi {
-		compatible = "aspeed,ast2500-cf-fsi-master", "fsi-master";
+		compatible = "aspeed,ast2500-cf-fsi-master";
 		#address-cells = <2>;
 		#size-cells = <0>;
-		no-gpio-delays;
 
 		memory-region = <&coldfire_memory>;
 		aspeed,sram = <&sram>;
@@ -96,7 +95,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		checkstop {
+		event-checkstop {
 			label = "checkstop";
 			gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(J, 2)>;
@@ -248,27 +247,27 @@
 	/*AB0-AB7*/	"","","","","","","","",
 	/*AC0-AC7*/	"","","","","","","","";
 
-	func_mode0 {
+	func-mode0-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(D, 3) GPIO_ACTIVE_HIGH>;
 		output-low;
 	};
-	func_mode1 {
+	func-mode1-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(D, 4) GPIO_ACTIVE_HIGH>;
 		output-low;
 	};
-	func_mode2 {
+	func-mode2-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(D, 5) GPIO_ACTIVE_HIGH>;
 		output-low;
 	};
-	seq_cont {
+	seq-cont-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(S, 7) GPIO_ACTIVE_HIGH>;
 		output-low;
 	};
-	ncsi_cfg {
+	ncsi-cfg-hog {
 		gpio-hog;
 		input;
 		gpios = <ASPEED_GPIO(E, 1) GPIO_ACTIVE_HIGH>;
@@ -284,10 +283,6 @@
 	memory-region = <&gfx_memory>;
 };
 
-&pinctrl {
-	aspeed,external-nodes = <&gfx &lhc>;
-};
-
 &ibt {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-palmetto.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-palmetto.dts
index cd660c1ff3f5..7953059a6c67 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-palmetto.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-palmetto.dts
@@ -55,7 +55,7 @@
 	};
 
 	fsi: gpio-fsi {
-		compatible = "aspeed,ast2400-cf-fsi-master", "fsi-master";
+		compatible = "aspeed,ast2400-cf-fsi-master";
 		#address-cells = <2>;
 		#size-cells = <0>;
 
@@ -73,7 +73,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		checkstop {
+		event-checkstop {
 			label = "checkstop";
 			gpios = <&gpio ASPEED_GPIO(P, 5) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(P, 5)>;
@@ -151,7 +151,7 @@
 	};
 
 	rtc@68 {
-		compatible = "dallas,ds3231";
+		compatible = "maxim,ds3231";
 		reg = <0x68>;
 	};
 };
@@ -209,140 +209,140 @@
 };
 
 &gpio {
-	pin_func_mode0 {
+	pin-func-mode0-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(C, 4) GPIO_ACTIVE_HIGH>;
 		output-low;
 		line-name = "func_mode0";
 	};
 
-	pin_func_mode1 {
+	pin-func-mode1-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(C, 5)  GPIO_ACTIVE_HIGH>;
 		output-low;
 		line-name = "func_mode1";
 	};
 
-	pin_func_mode2 {
+	pin-func-mode2-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(C, 6) GPIO_ACTIVE_HIGH>;
 		output-low;
 		line-name = "func_mode2";
 	};
 
-	pin_gpio_a0 {
+	pin-gpio-a0-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(A, 0) GPIO_ACTIVE_HIGH>;
 		input;
 		line-name = "BMC_FAN_RESERVED_N";
 	};
 
-	pin_gpio_a1 {
+	pin-gpio-a1-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(A, 1) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "APSS_WDT_N";
 	};
 
-	pin_gpio_b1 {
+	pin-gpio-b1-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(B, 1) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "APSS_BOOT_MODE";
 	};
 
-	pin_gpio_b2 {
+	pin-gpio-b2-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(B, 2) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "APSS_RESET_N";
 	};
 
-	pin_gpio_b7 {
+	pin-gpio-b7-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(B, 7) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "SPIVID_STBY_RESET_N";
 	};
 
-	pin_gpio_d1 {
+	pin-gpio-d1-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(D, 1) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "BMC_POWER_UP";
 	};
 
-	pin_gpio_f1 {
+	pin-gpio-f1-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(F, 1) GPIO_ACTIVE_HIGH>;
 		input;
 		line-name = "BMC_BATTERY_TEST";
 	};
 
-	pin_gpio_f4 {
+	pin-gpio-f4-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(F, 4) GPIO_ACTIVE_HIGH>;
 		input;
 		line-name = "AST_HW_FAULT_N";
 	};
 
-	pin_gpio_f5 {
+	pin-gpio-f5-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(F, 5) GPIO_ACTIVE_HIGH>;
 		input;
 		line-name = "AST_SYS_FAULT_N";
 	};
 
-	pin_gpio_f7 {
+	pin-gpio-f7-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(F, 7) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "BMC_FULL_SPEED_N";
 	};
 
-	pin_gpio_g3 {
+	pin-gpio-g3-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(G, 3) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "BMC_FAN_ERROR_N";
 	};
 
-	pin_gpio_g4 {
+	pin-gpio-g4-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(G, 4) GPIO_ACTIVE_HIGH>;
 		input;
 		line-name = "BMC_WDT_RST1_P";
 	};
 
-	pin_gpio_g5 {
+	pin-gpio-g5-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(G, 5) GPIO_ACTIVE_HIGH>;
 		input;
 		line-name = "BMC_WDT_RST2_P";
 	};
 
-	pin_gpio_h0 {
+	pin-gpio-h0-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(H, 0) GPIO_ACTIVE_HIGH>;
 		input;
 		line-name = "PE_SLOT_TEST_EN_N";
 	};
 
-	pin_gpio_h1 {
+	pin-gpio-h1-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(H, 1) GPIO_ACTIVE_HIGH>;
 		input;
 		line-name = "BMC_RTCRST_N";
 	};
 
-	pin_gpio_h2 {
+	pin-gpio-h2-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
 		output-high;
 		line-name = "SYS_PWROK_BMC";
 	};
 
-	pin_gpio_h7 {
+	pin-gpio-h7-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(H, 7) GPIO_ACTIVE_HIGH>;
 		output-high;
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-romulus.dts
index 084f54866f38..a0263d969e51 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-romulus.dts
@@ -68,10 +68,9 @@
 	};
 
 	fsi: gpio-fsi {
-		compatible = "aspeed,ast2500-cf-fsi-master", "fsi-master";
+		compatible = "aspeed,ast2500-cf-fsi-master";
 		#address-cells = <2>;
 		#size-cells = <0>;
-		no-gpio-delays;
 
 		memory-region = <&coldfire_memory>;
 		aspeed,sram = <&sram>;
@@ -87,7 +86,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		checkstop {
+		event-checkstop {
 			label = "checkstop";
 			gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(J, 2)>;
@@ -263,17 +262,17 @@
 	/*AB0-AB7*/	"","","","","","","","",
 	/*AC0-AC7*/	"","","","","","","","";
 
-	nic_func_mode0 {
+	nic-func-mode0-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(D, 3) GPIO_ACTIVE_HIGH>;
 		output-low;
 	};
-	nic_func_mode1 {
+	nic-func-mode1-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(D, 4) GPIO_ACTIVE_HIGH>;
 		output-low;
 	};
-	seq_cont {
+	seq-cont-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(S, 7) GPIO_ACTIVE_HIGH>;
 		output-low;
@@ -289,10 +288,6 @@
 	memory-region = <&gfx_memory>;
 };
 
-&pinctrl {
-	aspeed,external-nodes = <&gfx &lhc>;
-};
-
 &pwm_tacho {
 	status = "okay";
 	pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-tacoma.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-tacoma.dts
index 72b7a6639ed9..b31eb8e58c6b 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-tacoma.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-tacoma.dts
@@ -50,13 +50,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		ps0-presence {
+		event-ps0-presence {
 			label = "ps0-presence";
 			gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(H, 3)>;
 		};
 
-		ps1-presence {
+		event-ps1-presence {
 			label = "ps1-presence";
 			gpios = <&gpio0 ASPEED_GPIO(E, 5) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(E, 5)>;
@@ -65,29 +65,27 @@
 
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		poll-interval = <1000>;
 
-		fan0-presence {
+		event-fan0-presence {
 			label = "fan0-presence";
 			gpios = <&pca0 4 GPIO_ACTIVE_LOW>;
 			linux,code = <4>;
 		};
 
-		fan1-presence {
+		event-fan1-presence {
 			label = "fan1-presence";
 			gpios = <&pca0 5 GPIO_ACTIVE_LOW>;
 			linux,code = <5>;
 		};
 
-		fan2-presence {
+		event-fan2-presence {
 			label = "fan2-presence";
 			gpios = <&pca0 6 GPIO_ACTIVE_LOW>;
 			linux,code = <6>;
 		};
 
-		fan3-presence {
+		event-fan3-presence {
 			label = "fan3-presence";
 			gpios = <&pca0 7 GPIO_ACTIVE_LOW>;
 			linux,code = <7>;
@@ -458,7 +456,7 @@
 	status = "okay";
 
 	tpm: tpm@2e {
-		compatible = "tcg,tpm-tis-i2c";
+		compatible = "nuvoton,npct75x", "tcg,tpm-tis-i2c";
 		reg = <0x2e>;
 	};
 };
@@ -872,11 +870,6 @@
 		    <&pinctrl_lsirq_default>;
 };
 
-&xdma {
-	status = "okay";
-	memory-region = <&vga_memory>;
-};
-
 &kcs2 {
 	status = "okay";
 	aspeed,lpc-io-reg = <0xca8 0xcac>;
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-vesnin.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-vesnin.dts
index 328ef472c479..8a7fb55ab489 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-vesnin.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-vesnin.dts
@@ -63,13 +63,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		button_checkstop {
+		event-checkstop {
 			label = "checkstop";
 			linux,code = <74>;
 			gpios = <&gpio ASPEED_GPIO(P, 5) GPIO_ACTIVE_LOW>;
 		};
 
-		button_identify {
+		event-identify {
 			label = "identify";
 			linux,code = <152>;
 			gpios = <&gpio ASPEED_GPIO(O, 7) GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-witherspoon.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-witherspoon.dts
index 230f3584bcab..89907b628b65 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-witherspoon.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-witherspoon.dts
@@ -51,25 +51,25 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		air-water {
+		event-air-water {
 			label = "air-water";
 			gpios = <&gpio ASPEED_GPIO(B, 5) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(B, 5)>;
 		};
 
-		checkstop {
+		event-checkstop {
 			label = "checkstop";
 			gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(J, 2)>;
 		};
 
-		ps0-presence {
+		event-ps0-presence {
 			label = "ps0-presence";
 			gpios = <&gpio ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(P, 7)>;
 		};
 
-		ps1-presence {
+		event-ps1-presence {
 			label = "ps1-presence";
 			gpios = <&gpio ASPEED_GPIO(N, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(N, 0)>;
@@ -85,25 +85,25 @@
 		compatible = "gpio-keys-polled";
 		poll-interval = <1000>;
 
-		fan0-presence {
+		event-fan0-presence {
 			label = "fan0-presence";
 			gpios = <&pca0 4 GPIO_ACTIVE_LOW>;
 			linux,code = <4>;
 		};
 
-		fan1-presence {
+		event-fan1-presence {
 			label = "fan1-presence";
 			gpios = <&pca0 5 GPIO_ACTIVE_LOW>;
 			linux,code = <5>;
 		};
 
-		fan2-presence {
+		event-fan2-presence {
 			label = "fan2-presence";
 			gpios = <&pca0 6 GPIO_ACTIVE_LOW>;
 			linux,code = <6>;
 		};
 
-		fan3-presence {
+		event-fan3-presence {
 			label = "fan3-presence";
 			gpios = <&pca0 7 GPIO_ACTIVE_LOW>;
 			linux,code = <7>;
@@ -173,7 +173,7 @@
 	};
 
 	fsi: gpio-fsi {
-		compatible = "fsi-master-gpio", "fsi-master";
+		compatible = "fsi-master-gpio";
 		#address-cells = <2>;
 		#size-cells = <0>;
 		no-gpio-delays;
@@ -661,10 +661,6 @@
 	memory-region = <&gfx_memory>;
 };
 
-&pinctrl {
-	aspeed,external-nodes = <&gfx &lhc>;
-};
-
 &wdt1 {
 	aspeed,reset-type = "none";
 	aspeed,external-signal;
@@ -696,9 +692,4 @@
 	memory-region = <&video_engine_memory>;
 };
 
-&xdma {
-	status = "okay";
-	memory-region = <&vga_memory>;
-};
-
 #include "ibm-power9-dual.dtsi"
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-zaius.dts
index 7ae4ea0d2931..af3a9d39d277 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-zaius.dts
@@ -58,13 +58,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		checkstop {
+		event-checkstop {
 			label = "checkstop";
 			gpios = <&gpio ASPEED_GPIO(F, 7) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(F, 7)>;
 		};
 
-		pcie-e2b-present{
+		event-pcie-e2b-present {
 			label = "pcie-e2b-present";
 			gpios = <&gpio ASPEED_GPIO(E, 7) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(E, 7)>;
@@ -96,7 +96,7 @@
 	};
 
 	fsi: gpio-fsi {
-		compatible = "fsi-master-gpio", "fsi-master";
+		compatible = "fsi-master-gpio";
 		#address-cells = <2>;
 		#size-cells = <0>;
 		no-gpio-delays;
@@ -231,7 +231,7 @@
 &i2c1 {
 	status = "okay";
 
-	i2c-switch@71 {
+	i2c-mux@71 {
 		compatible = "nxp,pca9546";
 		reg = <0x71>;
 		#address-cells = <1>;
@@ -282,7 +282,7 @@
 &i2c4 {
 	status = "okay";
 
-	i2c-switch@71 {
+	i2c-mux@71 {
 		compatible = "nxp,pca9546";
 		reg = <0x71>;
 		#address-cells = <1>;
@@ -466,8 +466,6 @@
 };
 
 &pinctrl {
-	aspeed,external-nodes = <&gfx &lhc>;
-
 	pinctrl_gpioh_unbiased: gpioi_unbiased {
 		pins = "A8", "C7", "B7", "A7", "D7", "B6", "A6", "E7";
 		bias-disable;
@@ -511,25 +509,25 @@
 	/*AB0-AB7*/	"","","","","","","","",
 	/*AC0-AC7*/	"","","","","","","","";
 
-	line_iso_u146_en {
+	line-iso-u146-en-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(O, 4) GPIO_ACTIVE_HIGH>;
 		output-high;
 	};
 
-	ncsi_mux_en_n {
+	ncsi-mux-en-n-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(P, 0) GPIO_ACTIVE_HIGH>;
 		output-low;
 	};
 
-	line_bmc_i2c2_sw_rst_n {
+	line-bmc-i2c2-sw-rst-n-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(P, 1) GPIO_ACTIVE_HIGH>;
 		output-high;
 	};
 
-	line_bmc_i2c5_sw_rst_n {
+	line-bmc-i2c5-sw-rst-n-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(P, 3) GPIO_ACTIVE_HIGH>;
 		output-high;
diff --git a/arch/arm/boot/dts/aspeed-bmc-portwell-neptune.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-portwell-neptune.dts
index 61bc74b423cf..a5e64ccc2b3a 100644
--- a/arch/arm/boot/dts/aspeed-bmc-portwell-neptune.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-portwell-neptune.dts
@@ -24,17 +24,17 @@
 	leds {
 		compatible = "gpio-leds";
 		postcode0 {
-			label="BMC_UP";
+			label = "BMC_UP";
 			gpios = <&gpio ASPEED_GPIO(H, 0) GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 		};
 		postcode1 {
-			label="BMC_HB";
+			label = "BMC_HB";
 			gpios = <&gpio ASPEED_GPIO(H, 1) GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 		postcode2 {
-			label="FAULT";
+			label = "FAULT";
 			gpios = <&gpio ASPEED_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
 		};
 		// postcode3-7 are GPIOH3-H7
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-qcom-dc-scm-v1.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-qcom-dc-scm-v1.dts
new file mode 100644
index 000000000000..259ef3f54c5c
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-qcom-dc-scm-v1.dts
@@ -0,0 +1,190 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright (c) 2021-2022 Qualcomm Innovation Center, Inc. All rights reserved.
+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+
+/ {
+	model = "Qualcomm DC-SCM V1 BMC";
+	compatible = "qcom,dc-scm-v1-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial4 = &uart5;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+};
+
+&mdio3 {
+	status = "okay";
+
+	ethphy3: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&mac2 {
+	status = "okay";
+
+	/* Bootloader sets up the MAC to insert delay */
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy3>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii3_default>;
+};
+
+&mac3 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+
+	use-ncsi;
+};
+
+&rtc {
+	status = "okay";
+};
+
+&fmc {
+	status = "okay";
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <133000000>;
+#include "openbmc-flash-layout-64.dtsi"
+	};
+
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "alt-bmc";
+		spi-max-frequency = <133000000>;
+#include "openbmc-flash-layout-64-alt.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bios";
+		spi-max-frequency = <133000000>;
+	};
+};
+
+&gpio0 {
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","","","",
+	/*B0-B7*/	"BMC_FLASH_MUX_SEL","","","","","","","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"","","","","","","","",
+	/*F0-F7*/	"","","","","","","","",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"","","","","","","","",
+	/*I0-I7*/	"","","","","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"BMC_FWSPI_RST_N","","GPIO_1_BMC_3V3","","","","","",
+	/*O0-O7*/	"JTAG_MUX_A","JTAG_MUX_B","","","","","","",
+	/*P0-P7*/	"","","","","","","","",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","","","","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","SCMFPGA_SPARE_GPIO1_3V3",
+			"SCMFPGA_SPARE_GPIO2_3V3","SCMFPGA_SPARE_GPIO3_3V3",
+			"SCMFPGA_SPARE_GPIO4_3V3","SCMFPGA_SPARE_GPIO5_3V3",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"","","","","","","","",
+	/*AA0-AA7*/	"","","","","","","","",
+	/*AB0-AB7*/	"","","","","","","","",
+	/*AC0-AC7*/	"","","","","","","","";
+};
+
+&gpio1 {
+	gpio-line-names =
+	/*A0-A7*/	"GPI_1_BMC_1V8","","","","","",
+			"SCMFPGA_SPARE_GPIO1_1V8","SCMFPGA_SPARE_GPIO2_1V8",
+	/*B0-B7*/	"SCMFPGA_SPARE_GPIO3_1V8","SCMFPGA_SPARE_GPIO4_1V8",
+			"SCMFPGA_SPARE_GPIO5_1V8","","","","","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","BMC_SPI1_RST_N","BIOS_FLASH_MUX_SEL","",
+			"","TPM2_PIRQ_N","TPM2_RST_N","",
+	/*E0-E7*/	"","","","","","","","";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c12 {
+	status = "okay";
+};
+
+&i2c13 {
+	status = "okay";
+};
+
+&i2c14 {
+	status = "okay";
+};
+
+&i2c15 {
+	status = "okay";
+};
+
+&vhub {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-quanta-q71l.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-quanta-q71l.dts
index 9605e53f5bbf..fed2791f5994 100644
--- a/arch/arm/boot/dts/aspeed-bmc-quanta-q71l.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-quanta-q71l.dts
@@ -197,7 +197,7 @@
 	 *    Slot 6,
 	 *    Slot 7
 	 */
-	i2c-switch@74 {
+	i2c-mux@74 {
 		compatible = "nxp,pca9546";
 		reg = <0x74>;
 		#address-cells = <1>;
@@ -238,7 +238,7 @@
 	 *    SSD 1,
 	 *    SSD 2
 	 */
-	i2c-switch@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -325,7 +325,7 @@
 	 *    PSU3
 	 *    PSU2
 	 */
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		reg = <0x70>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/aspeed-bmc-quanta-s6q.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-quanta-s6q.dts
index 69e1bd256271..86451227847b 100644
--- a/arch/arm/boot/dts/aspeed-bmc-quanta-s6q.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-quanta-s6q.dts
@@ -65,19 +65,19 @@
 		compatible = "gpio-leds";
 
 		BMC_HEARTBEAT_N {
-			label="BMC_HEARTBEAT_N";
+			label = "BMC_HEARTBEAT_N";
 			gpios = <&gpio0 ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "heartbeat";
 		};
 
 		BMC_LED_STATUS_AMBER_N {
-			label="BMC_LED_STATUS_AMBER_N";
+			label = "BMC_LED_STATUS_AMBER_N";
 			gpios = <&gpio0 ASPEED_GPIO(S, 6) GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
 
 		FM_ID_LED_N {
-			label="FM_ID_LED_N";
+			label = "FM_ID_LED_N";
 			gpios = <&gpio0 ASPEED_GPIO(B, 5) GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
@@ -285,7 +285,7 @@
 		reg = <0x4b>;
 	};
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9546";
 		reg = <0x70>;
 		#address-cells = <1>;
@@ -321,7 +321,7 @@
 &i2c1 {
 	status = "okay";
 
-	i2c-switch@59 {
+	i2c-mux@59 {
 		compatible = "nxp,pca9848";
 		reg = <0x59>;
 		#address-cells = <1>;
@@ -381,7 +381,7 @@
 			#size-cells = <0>;
 			reg = <5>;
 
-			U190_fru@51 {
+			eeprom@51 {
 				compatible = "atmel,24c128";
 				reg = <0x51>;
 				pagesize = <32>;
@@ -393,7 +393,7 @@
 			#size-cells = <0>;
 			reg = <7>;
 
-			i2c-switch@77 {
+			i2c-mux@77 {
 				compatible = "nxp,pca9546";
 				reg = <0x77>;
 				#address-cells = <1>;
@@ -460,7 +460,7 @@
 	status = "okay";
 
 	/* MB FRU (U173) @ 0xA2 */
-	mb_fru: mb_fru@51 {
+	mb_fru: eeprom@51 {
 		compatible = "atmel,24c128";
 		reg = <0x51>;
 		pagesize = <32>;
@@ -472,7 +472,7 @@
 		reg = <0x4a>;
 	};
 
-	FP_U4_fru@52 {
+	eeprom@52 {
 		compatible = "atmel,24c02";
 		reg = <0x52>;
 		pagesize = <16>;
@@ -490,7 +490,7 @@
 &i2c6 {
 	status = "okay";
 
-	i2c-switch@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -509,7 +509,7 @@
 			reg = <1>;
 
 			cpu0_pvccin@60 {
-				compatible = "isil,raa229004";
+				compatible = "renesas,raa229004";
 				reg = <0x60>;
 			};
 
@@ -530,7 +530,7 @@
 			reg = <2>;
 
 			cpu1_pvccin@72 {
-				compatible = "isil,raa229004";
+				compatible = "renesas,raa229004";
 				reg = <0x72>;
 			};
 
@@ -556,7 +556,7 @@
 &i2c7 {
 	status = "okay";
 
-	i2c-switch@75 {
+	i2c-mux@75 {
 		compatible = "nxp,pca9546";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -593,7 +593,7 @@
 	status = "okay";
 
 	/* SCM FRU (U19) @ 0xA2 */
-	scm_fru: scm_fru@51 {
+	scm_fru: eeprom@51 {
 		compatible = "atmel,24c128";
 		reg = <0x51>;
 		pagesize = <32>;
diff --git a/arch/arm/boot/dts/aspeed-bmc-supermicro-x11spi.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-supermicro-x11spi.dts
index 50f3c6a5c0c8..b961dff388d1 100644
--- a/arch/arm/boot/dts/aspeed-bmc-supermicro-x11spi.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-supermicro-x11spi.dts
@@ -123,10 +123,6 @@
 	status = "okay";
 };
 
-&pinctrl {
-	aspeed,external-nodes = <&gfx &lhc>;
-};
-
 &pwm_tacho {
 	status = "okay";
 	pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/aspeed-bmc-tyan-s7106.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-tyan-s7106.dts
index aff27c1d4b06..aff27c1d4b06 100644
--- a/arch/arm/boot/dts/aspeed-bmc-tyan-s7106.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-tyan-s7106.dts
diff --git a/arch/arm/boot/dts/aspeed-bmc-tyan-s8036.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-tyan-s8036.dts
index 708ee78e4b83..f6c4549c0ac4 100644
--- a/arch/arm/boot/dts/aspeed-bmc-tyan-s8036.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-tyan-s8036.dts
@@ -364,6 +364,7 @@
 &kcs3 {
 	status = "okay";
 	aspeed,lpc-io-reg = <0xca2>;
+	aspeed,lpc-interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
 };
 
 /* Enable BMC VGA output to show an early (pre-BIOS) boot screen */
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-ufispace-ncplite.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-ufispace-ncplite.dts
new file mode 100644
index 000000000000..7ab29129d1e4
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-ufispace-ncplite.dts
@@ -0,0 +1,360 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright (c) 2022 Ufispace Co., Ltd.
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+	model = "Ufispace NCPLite BMC";
+	compatible = "ufispace,ncplite-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial4 = &uart5;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200n8 earlycon";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+			      <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+			      <&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>,
+			      <&adc1 4>, <&adc1 5>, <&adc1 6>, <&adc1 7>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		fan-status-int-l {
+			label = "fan-status-int-l";
+			gpios = <&gpio0 ASPEED_GPIO(M, 2) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(M, 2)>;
+		};
+
+		allpwr-good {
+			label = "allpwr-good";
+			gpios = <&gpio0 ASPEED_GPIO(V, 4) GPIO_ACTIVE_HIGH>;
+			linux,code = <ASPEED_GPIO(V, 4)>;
+		};
+
+		psu0-alert-n {
+			label = "psu0-alert-n";
+			gpios = <&gpio0 ASPEED_GPIO(V, 1) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(V, 1)>;
+		};
+
+		psu1-alert-n {
+			label = "psu1-alert-n";
+			gpios = <&gpio0 ASPEED_GPIO(V, 2) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(V, 2)>;
+		};
+
+		int-thermal-alert {
+			label = "int-thermal-alert";
+			gpios = <&gpio0 ASPEED_GPIO(P, 2) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(P, 2)>;
+		};
+
+		cpu-caterr-l {
+			label = "cpu-caterr-l";
+			gpios = <&gpio0 ASPEED_GPIO(N, 3) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(N, 3)>;
+		};
+
+		cpu-thermtrip-l {
+			label = "cpu-thermtrip-l";
+			gpios = <&gpio0 ASPEED_GPIO(V, 5) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(V, 5)>;
+		};
+
+		psu0-presence-l {
+			label = "psu0-presence-l";
+			gpios = <&gpio0 ASPEED_GPIO(F, 6) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(F, 6)>;
+		};
+
+		psu1-presence-l {
+			label = "psu1-presence-l";
+			gpios = <&gpio0 ASPEED_GPIO(F, 7) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(F, 7)>;
+		};
+
+		psu0-power-ok {
+			label = "psu0-power-ok";
+			gpios = <&gpio0 ASPEED_GPIO(M, 4) GPIO_ACTIVE_HIGH>;
+			linux,code = <ASPEED_GPIO(M, 4)>;
+		};
+
+		psu1-power-ok {
+			label = "psu1-power-ok";
+			gpios = <&gpio0 ASPEED_GPIO(M, 5) GPIO_ACTIVE_HIGH>;
+			linux,code = <ASPEED_GPIO(M, 5)>;
+		};
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <1000>;
+
+		fan0-presence {
+			label = "fan0-presence";
+			gpios = <&fan_ioexp 2 GPIO_ACTIVE_LOW>;
+			linux,code = <2>;
+		};
+
+		fan1-presence {
+			label = "fan1-presence";
+			gpios = <&fan_ioexp 6 GPIO_ACTIVE_LOW>;
+			linux,code = <6>;
+		};
+
+		fan2-presence {
+			label = "fan2-presence";
+			gpios = <&fan_ioexp 10 GPIO_ACTIVE_LOW>;
+			linux,code = <10>;
+		};
+
+		fan3-presence {
+			label = "fan3-presence";
+			gpios = <&fan_ioexp 14 GPIO_ACTIVE_LOW>;
+			linux,code = <14>;
+		};
+	};
+};
+
+&mac2 {
+	status = "okay";
+	use-ncsi;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii3_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>,
+		 <&syscon ASPEED_CLK_MAC3RCLK>;
+	clock-names = "MACCLK", "RCLK";
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64.dtsi"
+	};
+
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "alt-bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64-alt.dtsi"
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+};
+
+&lpc_reset {
+	status = "okay";
+};
+
+&lpc_ctrl {
+	status = "okay";
+};
+
+&uart_routing {
+	status = "okay";
+};
+
+&wdt1 {
+	status = "okay";
+};
+
+&wdt2 {
+	status = "okay";
+};
+
+&peci0 {
+	status = "okay";
+};
+
+&udc {
+	status = "okay";
+};
+
+&adc0 {
+	vref = <2500>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+		&pinctrl_adc2_default &pinctrl_adc3_default
+		&pinctrl_adc4_default &pinctrl_adc5_default
+		&pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+	vref = <2500>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+		&pinctrl_adc10_default &pinctrl_adc11_default
+		&pinctrl_adc12_default &pinctrl_adc13_default
+		&pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+
+	lm75@48 {
+		compatible = "national,lm75";
+		reg = <0x48>;
+	};
+
+	lm75@49 {
+		compatible = "national,lm75";
+		reg = <0x49>;
+	};
+
+	lm86@4c {
+		compatible = "national,lm86";
+		reg = <0x4c>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	lm75@4f {
+		cpmpatible = "national,lm75";
+		reg = <0x4f>;
+	};
+
+	fan_ioexp: pca9535@20 {
+		compatible = "nxp,pca9535";
+		reg = <0x20>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"","","presence-fan0","",
+		"","","presence-fan1","",
+		"","","presence-fan2","",
+		"","","presence-fan3","";
+	};
+};
+
+&i2c3 {
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+		pagesize = <64>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+
+	psu@58 {
+		compatible = "pmbus";
+		reg = <0x58>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <1>;
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	psu@58 {
+		compatible = "pmbus";
+		reg = <0x58>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <1>;
+	};
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c10 {
+	status = "okay";
+
+	lm75@4d {
+		compatible = "national,lm75";
+		reg = <0x4d>;
+	};
+};
+
+&gpio0 {
+	status = "okay";
+
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","","","",
+	/*B0-B7*/	"","","","","","","","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"","","","","","","","",
+	/*F0-F7*/	"CPU_PWRGD","","","power-button","host0-ready","","presence-ps0","presence-ps1",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"","","","","","","","",
+	/*I0-I7*/	"","","","","","reset-button","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"power-chassis-control0","power-chassis-control1","","","","","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"","","","","","","","",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","","","","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","power-chassis-good","","","";
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-vegman-n110.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-vegman-n110.dts
index 24319267d550..44b9853f6e63 100644
--- a/arch/arm/boot/dts/aspeed-bmc-vegman-n110.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-vegman-n110.dts
@@ -88,16 +88,16 @@
 
 &i2c13 {
 	/* SMB_PCIE2_STBY_LVC3 */
-	mux-expa@73 {
-		compatible = "nxp,pca9545";
-		reg = <0x73>;
+	i2c-mux@71 {
+		compatible = "nxp,pca9543";
+		reg = <0x71>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 		i2c-mux-idle-disconnect;
 	};
-	mux-sata@71 {
-		compatible = "nxp,pca9543";
-		reg = <0x71>;
+	i2c-mux@73 {
+		compatible = "nxp,pca9545";
+		reg = <0x73>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 		i2c-mux-idle-disconnect;
@@ -106,7 +106,7 @@
 
 &i2c2 {
 	/* SMB_PCIE_STBY_LVC3 */
-	mux-expb@71 {
+	i2c-mux@71 {
 		compatible = "nxp,pca9545";
 		reg = <0x71>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/aspeed-bmc-vegman-rx20.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-vegman-rx20.dts
index ebbb68b55559..98f3e0437704 100644
--- a/arch/arm/boot/dts/aspeed-bmc-vegman-rx20.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-vegman-rx20.dts
@@ -133,7 +133,7 @@
 
 &i2c13 {
 	/* SMB_PCIE2_STBY_LVC3 */
-	mux-expa@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		reg = <0x70>;
 		#address-cells = <1>;
@@ -144,7 +144,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <2>;
-			rsra-mux@72 {
+			i2c-mux@72 {
 				compatible = "nxp,pca9548";
 				reg = <0x72>;
 				#address-cells = <1>;
@@ -154,7 +154,7 @@
 					#address-cells = <1>;
 					#size-cells = <0>;
 					reg = <7>;
-					at24@50 {
+					eeprom@50 {
 						compatible = "atmel,24c64";
 						reg = <0x50>;
 						pagesize = <32>;
@@ -165,7 +165,7 @@
 			};
 		};
 	};
-	mux-sata@71 {
+	i2c-mux@71 {
 		compatible = "nxp,pca9543";
 		reg = <0x71>;
 		#address-cells = <1>;
@@ -176,7 +176,7 @@
 
 &i2c2 {
 	/* SMB_PCIE_STBY_LVC3 */
-	mux-expb@71 {
+	i2c-mux@71 {
 		compatible = "nxp,pca9548";
 		reg = <0x71>;
 		#address-cells = <1>;
@@ -187,7 +187,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0>;
-			rsrb-mux@72 {
+			i2c-mux@72 {
 				compatible = "nxp,pca9548";
 				reg = <0x72>;
 				#address-cells = <1>;
@@ -196,7 +196,7 @@
 					#address-cells = <1>;
 					#size-cells = <0>;
 					reg = <7>;
-					at24@50 {
+					eeprom@50 {
 						compatible = "atmel,24c64";
 						reg = <0x50>;
 						pagesize = <32>;
@@ -205,7 +205,7 @@
 					};
 				};
 			};
-			at24@50 {
+			eeprom@50 {
 				compatible = "atmel,24c64";
 				reg = <0x50>;
 				pagesize = <32>;
diff --git a/arch/arm/boot/dts/aspeed-bmc-vegman-sx20.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-vegman-sx20.dts
index e36ee4704994..933ca831d375 100644
--- a/arch/arm/boot/dts/aspeed-bmc-vegman-sx20.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-vegman-sx20.dts
@@ -88,16 +88,16 @@
 
 &i2c13 {
 	/* SMB_PCIE2_STBY_LVC3 */
-	mux-expa@73 {
-		compatible = "nxp,pca9545";
-		reg = <0x73>;
+	i2c-mux@71 {
+		compatible = "nxp,pca9543";
+		reg = <0x71>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 		i2c-mux-idle-disconnect;
 	};
-	mux-sata@71 {
-		compatible = "nxp,pca9543";
-		reg = <0x71>;
+	i2c-mux@73 {
+		compatible = "nxp,pca9545";
+		reg = <0x73>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 		i2c-mux-idle-disconnect;
@@ -106,7 +106,7 @@
 
 &i2c2 {
 	/* SMB_PCIE_STBY_LVC3 */
-	mux-expb@71 {
+	i2c-mux@71 {
 		compatible = "nxp,pca9545";
 		reg = <0x71>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/aspeed-bmc-vegman.dtsi b/arch/arm/boot/dts/aspeed/aspeed-bmc-vegman.dtsi
index 1a5b25b2ea29..8c953e3a1d41 100644
--- a/arch/arm/boot/dts/aspeed-bmc-vegman.dtsi
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-vegman.dtsi
@@ -30,7 +30,7 @@
 			reusable;
 		};
 
-		ramoops@9eff0000{
+		ramoops@9eff0000 {
 			compatible = "ramoops";
 			reg = <0x9eff0000 0x10000>;
 			record-size = <0x2000>;
@@ -291,7 +291,7 @@
 	/* SMB_BMC_MGMT_LVC3 */
 	status = "okay";
 
-	at24@50 {
+	eeprom@50 {
 		compatible = "atmel,24c64";
 		reg = <0x50>;
 		pagesize = <32>;
diff --git a/arch/arm/boot/dts/aspeed-g4.dtsi b/arch/arm/boot/dts/aspeed/aspeed-g4.dtsi
index fa8b581c3d6c..c3d4d916c69b 100644
--- a/arch/arm/boot/dts/aspeed-g4.dtsi
+++ b/arch/arm/boot/dts/aspeed/aspeed-g4.dtsi
@@ -54,8 +54,7 @@
 		ranges;
 
 		fmc: spi@1e620000 {
-			reg = < 0x1e620000 0x94
-				0x20000000 0x10000000 >;
+			reg = <0x1e620000 0x94>, <0x20000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2400-fmc";
@@ -65,34 +64,42 @@
 			flash@0 {
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
+				spi-rx-bus-width = <2>;
 				spi-max-frequency = <50000000>;
 				status = "disabled";
 			};
 			flash@1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
+				spi-rx-bus-width = <2>;
+				spi-max-frequency = <50000000>;
 				status = "disabled";
 			};
 			flash@2 {
 				reg = < 2 >;
 				compatible = "jedec,spi-nor";
+				spi-rx-bus-width = <2>;
+				spi-max-frequency = <50000000>;
 				status = "disabled";
 			};
 			flash@3 {
 				reg = < 3 >;
 				compatible = "jedec,spi-nor";
+				spi-rx-bus-width = <2>;
+				spi-max-frequency = <50000000>;
 				status = "disabled";
 			};
 			flash@4 {
 				reg = < 4 >;
 				compatible = "jedec,spi-nor";
+				spi-rx-bus-width = <2>;
+				spi-max-frequency = <50000000>;
 				status = "disabled";
 			};
 		};
 
 		spi: spi@1e630000 {
-			reg = < 0x1e630000 0x18
-				0x30000000 0x10000000 >;
+			reg = <0x1e630000 0x18>, <0x30000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2400-spi";
@@ -102,6 +109,7 @@
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
@@ -114,8 +122,8 @@
 			reg = <0x1e6c0080 0x80>;
 		};
 
-		cvic: copro-interrupt-controller@1e6c2000 {
-			compatible = "aspeed,ast2400-cvic", "aspeed-cvic";
+		cvic: interrupt-controller@1e6c2000 {
+			compatible = "aspeed,ast2400-cvic", "aspeed,cvic";
 			valid-sources = <0x7fffffff>;
 			reg = <0x1e6c2000 0x80>;
 		};
@@ -222,6 +230,9 @@
 			sram: sram@1e720000 {
 				compatible = "mmio-sram";
 				reg = <0x1e720000 0x8000>;	// 32K
+				ranges;
+				#address-cells = <1>;
+				#size-cells = <1>;
 			};
 
 			video: video@1e700000 {
@@ -345,7 +356,6 @@
 			lpc: lpc@1e789000 {
 				compatible = "aspeed,ast2400-lpc-v2", "simple-mfd", "syscon";
 				reg = <0x1e789000 0x1000>;
-				reg-io-width = <4>;
 
 				#address-cells = <1>;
 				#size-cells = <1>;
@@ -455,10 +465,9 @@
 		interrupt-controller;
 	};
 
-	i2c0: i2c-bus@40 {
+	i2c0: i2c@40 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0x40 0x40>;
 		compatible = "aspeed,ast2400-i2c-bus";
@@ -471,10 +480,9 @@
 		/* Does not need pinctrl properties */
 	};
 
-	i2c1: i2c-bus@80 {
+	i2c1: i2c@80 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0x80 0x40>;
 		compatible = "aspeed,ast2400-i2c-bus";
@@ -487,10 +495,9 @@
 		/* Does not need pinctrl properties */
 	};
 
-	i2c2: i2c-bus@c0 {
+	i2c2: i2c@c0 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0xc0 0x40>;
 		compatible = "aspeed,ast2400-i2c-bus";
@@ -504,10 +511,9 @@
 		status = "disabled";
 	};
 
-	i2c3: i2c-bus@100 {
+	i2c3: i2c@100 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0x100 0x40>;
 		compatible = "aspeed,ast2400-i2c-bus";
@@ -521,10 +527,9 @@
 		status = "disabled";
 	};
 
-	i2c4: i2c-bus@140 {
+	i2c4: i2c@140 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0x140 0x40>;
 		compatible = "aspeed,ast2400-i2c-bus";
@@ -538,10 +543,9 @@
 		status = "disabled";
 	};
 
-	i2c5: i2c-bus@180 {
+	i2c5: i2c@180 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0x180 0x40>;
 		compatible = "aspeed,ast2400-i2c-bus";
@@ -555,10 +559,9 @@
 		status = "disabled";
 	};
 
-	i2c6: i2c-bus@1c0 {
+	i2c6: i2c@1c0 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0x1c0 0x40>;
 		compatible = "aspeed,ast2400-i2c-bus";
@@ -572,10 +575,9 @@
 		status = "disabled";
 	};
 
-	i2c7: i2c-bus@300 {
+	i2c7: i2c@300 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0x300 0x40>;
 		compatible = "aspeed,ast2400-i2c-bus";
@@ -589,10 +591,9 @@
 		status = "disabled";
 	};
 
-	i2c8: i2c-bus@340 {
+	i2c8: i2c@340 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0x340 0x40>;
 		compatible = "aspeed,ast2400-i2c-bus";
@@ -606,10 +607,9 @@
 		status = "disabled";
 	};
 
-	i2c9: i2c-bus@380 {
+	i2c9: i2c@380 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0x380 0x40>;
 		compatible = "aspeed,ast2400-i2c-bus";
@@ -623,10 +623,9 @@
 		status = "disabled";
 	};
 
-	i2c10: i2c-bus@3c0 {
+	i2c10: i2c@3c0 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0x3c0 0x40>;
 		compatible = "aspeed,ast2400-i2c-bus";
@@ -640,10 +639,9 @@
 		status = "disabled";
 	};
 
-	i2c11: i2c-bus@400 {
+	i2c11: i2c@400 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0x400 0x40>;
 		compatible = "aspeed,ast2400-i2c-bus";
@@ -657,10 +655,9 @@
 		status = "disabled";
 	};
 
-	i2c12: i2c-bus@440 {
+	i2c12: i2c@440 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0x440 0x40>;
 		compatible = "aspeed,ast2400-i2c-bus";
@@ -674,10 +671,9 @@
 		status = "disabled";
 	};
 
-	i2c13: i2c-bus@480 {
+	i2c13: i2c@480 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0x480 0x40>;
 		compatible = "aspeed,ast2400-i2c-bus";
diff --git a/arch/arm/boot/dts/aspeed-g5.dtsi b/arch/arm/boot/dts/aspeed/aspeed-g5.dtsi
index 4147b397c883..39500bdb4747 100644
--- a/arch/arm/boot/dts/aspeed-g5.dtsi
+++ b/arch/arm/boot/dts/aspeed/aspeed-g5.dtsi
@@ -55,8 +55,7 @@
 		ranges;
 
 		fmc: spi@1e620000 {
-			reg = < 0x1e620000 0xc4
-				0x20000000 0x10000000 >;
+			reg = <0x1e620000 0xc4>, <0x20000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2500-fmc";
@@ -67,25 +66,27 @@
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash@1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash@2 {
 				reg = < 2 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
 
 		spi1: spi@1e630000 {
-			reg = < 0x1e630000 0xc4
-				0x30000000 0x08000000 >;
+			reg = <0x1e630000 0xc4>, <0x30000000 0x08000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2500-spi";
@@ -95,19 +96,20 @@
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash@1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
 
 		spi2: spi@1e631000 {
-			reg = < 0x1e631000 0xc4
-				0x38000000 0x08000000 >;
+			reg = <0x1e631000 0xc4>, <0x38000000 0x08000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2500-spi";
@@ -117,12 +119,14 @@
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash@1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
@@ -135,8 +139,8 @@
 			reg = <0x1e6c0080 0x80>;
 		};
 
-		cvic: copro-interrupt-controller@1e6c2000 {
-			compatible = "aspeed,ast2500-cvic", "aspeed-cvic";
+		cvic: interrupt-controller@1e6c2000 {
+			compatible = "aspeed,ast2500-cvic", "aspeed,cvic";
 			valid-sources = <0xffffffff>;
 			copro-sw-interrupts = <1>;
 			reg = <0x1e6c2000 0x80>;
@@ -258,10 +262,17 @@
 				quality = <100>;
 			};
 
+			hace: crypto@1e6e3000 {
+				compatible = "aspeed,ast2500-hace";
+				reg = <0x1e6e3000 0x100>;
+				interrupts = <4>;
+				clocks = <&syscon ASPEED_CLK_GATE_YCLK>;
+				resets = <&syscon ASPEED_RESET_HACE>;
+			};
+
 			gfx: display@1e6e6000 {
 				compatible = "aspeed,ast2500-gfx", "syscon";
 				reg = <0x1e6e6000 0x1000>;
-				reg-io-width = <4>;
 				clocks = <&syscon ASPEED_CLK_GATE_D1CLK>;
 				resets = <&syscon ASPEED_RESET_CRT1>;
 				syscon = <&syscon>;
@@ -269,17 +280,6 @@
 				interrupts = <0x19>;
 			};
 
-			xdma: xdma@1e6e7000 {
-				compatible = "aspeed,ast2500-xdma";
-				reg = <0x1e6e7000 0x100>;
-				clocks = <&syscon ASPEED_CLK_GATE_BCLK>;
-				resets = <&syscon ASPEED_RESET_XDMA>;
-				interrupts-extended = <&vic 6>, <&scu_ic ASPEED_AST2500_SCU_IC_PCIE_RESET_LO_TO_HI>;
-				aspeed,pcie-device = "bmc";
-				aspeed,scu = <&syscon>;
-				status = "disabled";
-			};
-
 			adc: adc@1e6e9000 {
 				compatible = "aspeed,ast2500-adc";
 				reg = <0x1e6e9000 0xb0>;
@@ -302,6 +302,9 @@
 			sram: sram@1e720000 {
 				compatible = "mmio-sram";
 				reg = <0x1e720000 0x9000>;	// 36K
+				ranges;
+				#address-cells = <1>;
+				#size-cells = <1>;
 			};
 
 			sdmmc: sd-controller@1e740000 {
@@ -351,6 +354,7 @@
 				interrupts = <40>;
 				reg = <0x1e780200 0x0100>;
 				clocks = <&syscon ASPEED_CLK_APB>;
+				#interrupt-cells = <2>;
 				interrupt-controller;
 				bus-frequency = <12000000>;
 				pinctrl-names = "default";
@@ -436,7 +440,6 @@
 			lpc: lpc@1e789000 {
 				compatible = "aspeed,ast2500-lpc-v2", "simple-mfd", "syscon";
 				reg = <0x1e789000 0x1000>;
-				reg-io-width = <4>;
 
 				#address-cells = <1>;
 				#size-cells = <1>;
@@ -579,10 +582,9 @@
 		interrupt-controller;
 	};
 
-	i2c0: i2c-bus@40 {
+	i2c0: i2c@40 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0x40 0x40>;
 		compatible = "aspeed,ast2500-i2c-bus";
@@ -595,10 +597,9 @@
 		/* Does not need pinctrl properties */
 	};
 
-	i2c1: i2c-bus@80 {
+	i2c1: i2c@80 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0x80 0x40>;
 		compatible = "aspeed,ast2500-i2c-bus";
@@ -611,10 +612,9 @@
 		/* Does not need pinctrl properties */
 	};
 
-	i2c2: i2c-bus@c0 {
+	i2c2: i2c@c0 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0xc0 0x40>;
 		compatible = "aspeed,ast2500-i2c-bus";
@@ -628,10 +628,9 @@
 		status = "disabled";
 	};
 
-	i2c3: i2c-bus@100 {
+	i2c3: i2c@100 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0x100 0x40>;
 		compatible = "aspeed,ast2500-i2c-bus";
@@ -645,10 +644,9 @@
 		status = "disabled";
 	};
 
-	i2c4: i2c-bus@140 {
+	i2c4: i2c@140 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0x140 0x40>;
 		compatible = "aspeed,ast2500-i2c-bus";
@@ -662,10 +660,9 @@
 		status = "disabled";
 	};
 
-	i2c5: i2c-bus@180 {
+	i2c5: i2c@180 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0x180 0x40>;
 		compatible = "aspeed,ast2500-i2c-bus";
@@ -679,10 +676,9 @@
 		status = "disabled";
 	};
 
-	i2c6: i2c-bus@1c0 {
+	i2c6: i2c@1c0 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0x1c0 0x40>;
 		compatible = "aspeed,ast2500-i2c-bus";
@@ -696,10 +692,9 @@
 		status = "disabled";
 	};
 
-	i2c7: i2c-bus@300 {
+	i2c7: i2c@300 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0x300 0x40>;
 		compatible = "aspeed,ast2500-i2c-bus";
@@ -713,10 +708,9 @@
 		status = "disabled";
 	};
 
-	i2c8: i2c-bus@340 {
+	i2c8: i2c@340 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0x340 0x40>;
 		compatible = "aspeed,ast2500-i2c-bus";
@@ -730,10 +724,9 @@
 		status = "disabled";
 	};
 
-	i2c9: i2c-bus@380 {
+	i2c9: i2c@380 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0x380 0x40>;
 		compatible = "aspeed,ast2500-i2c-bus";
@@ -747,10 +740,9 @@
 		status = "disabled";
 	};
 
-	i2c10: i2c-bus@3c0 {
+	i2c10: i2c@3c0 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0x3c0 0x40>;
 		compatible = "aspeed,ast2500-i2c-bus";
@@ -764,10 +756,9 @@
 		status = "disabled";
 	};
 
-	i2c11: i2c-bus@400 {
+	i2c11: i2c@400 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0x400 0x40>;
 		compatible = "aspeed,ast2500-i2c-bus";
@@ -781,10 +772,9 @@
 		status = "disabled";
 	};
 
-	i2c12: i2c-bus@440 {
+	i2c12: i2c@440 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0x440 0x40>;
 		compatible = "aspeed,ast2500-i2c-bus";
@@ -798,10 +788,9 @@
 		status = "disabled";
 	};
 
-	i2c13: i2c-bus@480 {
+	i2c13: i2c@480 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 
 		reg = <0x480 0x40>;
 		compatible = "aspeed,ast2500-i2c-bus";
diff --git a/arch/arm/boot/dts/aspeed-g6-pinctrl.dtsi b/arch/arm/boot/dts/aspeed/aspeed-g6-pinctrl.dtsi
index e4775bbceecc..e87c4b58994a 100644
--- a/arch/arm/boot/dts/aspeed-g6-pinctrl.dtsi
+++ b/arch/arm/boot/dts/aspeed/aspeed-g6-pinctrl.dtsi
@@ -117,9 +117,9 @@
 		groups = "FWSPID";
 	};
 
-	pinctrl_fwqspid_default: fwqspid_default {
-		function = "FWSPID";
-		groups = "FWQSPID";
+	pinctrl_fwqspi_default: fwqspi_default {
+		function = "FWQSPI";
+		groups = "FWQSPI";
 	};
 
 	pinctrl_fwspiwp_default: fwspiwp_default {
@@ -297,6 +297,16 @@
 		groups = "I2C9";
 	};
 
+	pinctrl_i3c1_default: i3c1_default {
+		function = "I3C1";
+		groups = "I3C1";
+	};
+
+	pinctrl_i3c2_default: i3c2_default {
+		function = "I3C2";
+		groups = "I3C2";
+	};
+
 	pinctrl_i3c3_default: i3c3_default {
 		function = "I3C3";
 		groups = "I3C3";
@@ -402,6 +412,16 @@
 		groups = "MDIO4";
 	};
 
+	pinctrl_ncsi3_default: ncsi3_default {
+		function = "RMII3";
+		groups = "NCSI3";
+	};
+
+	pinctrl_ncsi4_default: ncsi4_default {
+		function = "RMII4";
+		groups = "NCSI4";
+	};
+
 	pinctrl_ncts1_default: ncts1_default {
 		function = "NCTS1";
 		groups = "NCTS1";
@@ -653,12 +673,12 @@
 	};
 
 	pinctrl_qspi1_default: qspi1_default {
-		function = "QSPI1";
+		function = "SPI1";
 		groups = "QSPI1";
 	};
 
 	pinctrl_qspi2_default: qspi2_default {
-		function = "QSPI2";
+		function = "SPI2";
 		groups = "QSPI2";
 	};
 
diff --git a/arch/arm/boot/dts/aspeed-g6.dtsi b/arch/arm/boot/dts/aspeed/aspeed-g6.dtsi
index 3d5ce9da42c3..f8662c8ac089 100644
--- a/arch/arm/boot/dts/aspeed-g6.dtsi
+++ b/arch/arm/boot/dts/aspeed/aspeed-g6.dtsi
@@ -36,6 +36,10 @@
 		serial4 = &uart5;
 		serial5 = &vuart1;
 		serial6 = &vuart2;
+		mdio0 = &mdio0;
+		mdio1 = &mdio1;
+		mdio2 = &mdio2;
+		mdio3 = &mdio3;
 	};
 
 
@@ -94,9 +98,13 @@
 			    <0x40466000 0x2000>;
 			};
 
+		ahbc: bus@1e600000 {
+			compatible = "aspeed,ast2600-ahbc", "syscon";
+			reg = <0x1e600000 0x100>;
+		};
+
 		fmc: spi@1e620000 {
-			reg = < 0x1e620000 0xc4
-				0x20000000 0x10000000 >;
+			reg = <0x1e620000 0xc4>, <0x20000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2600-fmc";
@@ -107,25 +115,27 @@
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash@1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash@2 {
 				reg = < 2 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
 
 		spi1: spi@1e630000 {
-			reg = < 0x1e630000 0xc4
-				0x30000000 0x10000000 >;
+			reg = <0x1e630000 0xc4>, <0x30000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2600-spi";
@@ -135,19 +145,20 @@
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash@1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
 
 		spi2: spi@1e631000 {
-			reg = < 0x1e631000 0xc4
-				0x50000000 0x10000000 >;
+			reg = <0x1e631000 0xc4>, <0x50000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2600-spi";
@@ -157,18 +168,21 @@
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash@1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash@2 {
 				reg = < 2 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
@@ -181,6 +195,7 @@
 			status = "disabled";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_mdio1_default>;
+			resets = <&syscon ASPEED_RESET_MII>;
 		};
 
 		mdio1: mdio@1e650008 {
@@ -191,6 +206,7 @@
 			status = "disabled";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_mdio2_default>;
+			resets = <&syscon ASPEED_RESET_MII>;
 		};
 
 		mdio2: mdio@1e650010 {
@@ -201,6 +217,7 @@
 			status = "disabled";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_mdio3_default>;
+			resets = <&syscon ASPEED_RESET_MII>;
 		};
 
 		mdio3: mdio@1e650018 {
@@ -211,43 +228,36 @@
 			status = "disabled";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_mdio4_default>;
+			resets = <&syscon ASPEED_RESET_MII>;
 		};
 
-		mac0: ftgmac@1e660000 {
+		mac0: ethernet@1e660000 {
 			compatible = "aspeed,ast2600-mac", "faraday,ftgmac100";
 			reg = <0x1e660000 0x180>;
-			#address-cells = <1>;
-			#size-cells = <0>;
 			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&syscon ASPEED_CLK_GATE_MAC1CLK>;
 			status = "disabled";
 		};
 
-		mac1: ftgmac@1e680000 {
+		mac1: ethernet@1e680000 {
 			compatible = "aspeed,ast2600-mac", "faraday,ftgmac100";
 			reg = <0x1e680000 0x180>;
-			#address-cells = <1>;
-			#size-cells = <0>;
 			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&syscon ASPEED_CLK_GATE_MAC2CLK>;
 			status = "disabled";
 		};
 
-		mac2: ftgmac@1e670000 {
+		mac2: ethernet@1e670000 {
 			compatible = "aspeed,ast2600-mac", "faraday,ftgmac100";
 			reg = <0x1e670000 0x180>;
-			#address-cells = <1>;
-			#size-cells = <0>;
 			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>;
 			status = "disabled";
 		};
 
-		mac3: ftgmac@1e690000 {
+		mac3: ethernet@1e690000 {
 			compatible = "aspeed,ast2600-mac", "faraday,ftgmac100";
 			reg = <0x1e690000 0x180>;
-			#address-cells = <1>;
-			#size-cells = <0>;
 			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&syscon ASPEED_CLK_GATE_MAC4CLK>;
 			status = "disabled";
@@ -298,12 +308,30 @@
 			status = "disabled";
 		};
 
+		udc: usb@1e6a2000 {
+			compatible = "aspeed,ast2600-udc";
+			reg = <0x1e6a2000 0x300>;
+			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&syscon ASPEED_CLK_GATE_USBPORT2CLK>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb2bd_default>;
+			status = "disabled";
+		};
+
 		apb {
 			compatible = "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
 
+			hace: crypto@1e6d0000 {
+				compatible = "aspeed,ast2600-hace";
+				reg = <0x1e6d0000 0x200>;
+				interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_GATE_YCLK>;
+				resets = <&syscon ASPEED_RESET_HACE>;
+			};
+
 			syscon: syscon@1e6e2000 {
 				compatible = "aspeed,ast2600-scu", "syscon", "simple-mfd";
 				reg = <0x1e6e2000 0x1000>;
@@ -351,17 +379,14 @@
 				quality = <100>;
 			};
 
-			xdma: xdma@1e6e7000 {
-				compatible = "aspeed,ast2600-xdma";
-				reg = <0x1e6e7000 0x100>;
-				clocks = <&syscon ASPEED_CLK_GATE_BCLK>;
-				resets = <&syscon ASPEED_RESET_DEV_XDMA>, <&syscon ASPEED_RESET_RC_XDMA>;
-				reset-names = "device", "root-complex";
-				interrupts-extended = <&gic GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
-						      <&scu_ic0 ASPEED_AST2600_SCU_IC0_PCIE_PERST_LO_TO_HI>;
-				aspeed,pcie-device = "bmc";
-				aspeed,scu = <&syscon>;
+			gfx: display@1e6e6000 {
+				compatible = "aspeed,ast2600-gfx", "syscon";
+				reg = <0x1e6e6000 0x1000>;
+				clocks = <&syscon ASPEED_CLK_GATE_D1CLK>;
+				resets = <&syscon ASPEED_RESET_GRAPHICS>;
+				syscon = <&syscon>;
 				status = "disabled";
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
 			adc0: adc@1e6e9000 {
@@ -389,6 +414,24 @@
 				reg = <0x1e6f2000 0x1000>;
 			};
 
+			acry: crypto@1e6fa000 {
+				compatible = "aspeed,ast2600-acry";
+				reg = <0x1e6fa000 0x400>, <0x1e710000 0x1800>;
+				interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_GATE_RSACLK>;
+				aspeed,ahbc = <&ahbc>;
+			};
+
+			video: video@1e700000 {
+				compatible = "aspeed,ast2600-video-engine";
+				reg = <0x1e700000 0x1000>;
+				clocks = <&syscon ASPEED_CLK_GATE_VCLK>,
+					 <&syscon ASPEED_CLK_GATE_ECLK>;
+				clock-names = "vclk", "eclk";
+				interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+
 			gpio0: gpio@1e780000 {
 				#gpio-cells = <2>;
 				gpio-controller;
@@ -409,6 +452,7 @@
 				reg = <0x1e780500 0x100>;
 				interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&syscon ASPEED_CLK_APB2>;
+				#interrupt-cells = <2>;
 				interrupt-controller;
 				bus-frequency = <12000000>;
 				pinctrl-names = "default";
@@ -423,6 +467,7 @@
 				reg = <0x1e780600 0x100>;
 				interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&syscon ASPEED_CLK_APB2>;
+				#interrupt-cells = <2>;
 				interrupt-controller;
 				bus-frequency = <12000000>;
 				pinctrl-names = "default";
@@ -526,7 +571,6 @@
 			lpc: lpc@1e789000 {
 				compatible = "aspeed,ast2600-lpc-v2", "simple-mfd", "syscon";
 				reg = <0x1e789000 0x1000>;
-				reg-io-width = <4>;
 
 				#address-cells = <1>;
 				#size-cells = <1>;
@@ -616,7 +660,7 @@
 				status = "disabled";
 
 				sdhci0: sdhci@1e740100 {
-					compatible = "aspeed,ast2600-sdhci", "sdhci";
+					compatible = "aspeed,ast2600-sdhci";
 					reg = <0x100 0x100>;
 					interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
 					sdhci,auto-cmd12;
@@ -625,7 +669,7 @@
 				};
 
 				sdhci1: sdhci@1e740200 {
-					compatible = "aspeed,ast2600-sdhci", "sdhci";
+					compatible = "aspeed,ast2600-sdhci";
 					reg = <0x200 0x100>;
 					interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
 					sdhci,auto-cmd12;
@@ -664,6 +708,16 @@
 				status = "disabled";
 			};
 
+			vuart3: serial@1e787800 {
+				compatible = "aspeed,ast2500-vuart";
+				reg = <0x1e787800 0x40>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_APB2>;
+				no-loopback-test;
+				status = "disabled";
+			};
+
 			vuart2: serial@1e788000 {
 				compatible = "aspeed,ast2500-vuart";
 				reg = <0x1e788000 0x40>;
@@ -674,6 +728,16 @@
 				status = "disabled";
 			};
 
+			vuart4: serial@1e788800 {
+				compatible = "aspeed,ast2500-vuart";
+				reg = <0x1e788800 0x40>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_APB2>;
+				no-loopback-test;
+				status = "disabled";
+			};
+
 			uart2: serial@1e78d000 {
 				compatible = "ns16550a";
 				reg = <0x1e78d000 0x20>;
@@ -716,6 +780,62 @@
 				status = "disabled";
 			};
 
+			uart6: serial@1e790000 {
+				compatible = "ns16550a";
+				reg = <0x1e790000 0x20>;
+				reg-shift = <2>;
+				reg-io-width = <4>;
+				interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_GATE_UART6CLK>;
+				no-loopback-test;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart6_default>;
+
+				status = "disabled";
+			};
+
+			uart7: serial@1e790100 {
+				compatible = "ns16550a";
+				reg = <0x1e790100 0x20>;
+				reg-shift = <2>;
+				reg-io-width = <4>;
+				interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_GATE_UART7CLK>;
+				no-loopback-test;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart7_default>;
+
+				status = "disabled";
+			};
+
+			uart8: serial@1e790200 {
+				compatible = "ns16550a";
+				reg = <0x1e790200 0x20>;
+				reg-shift = <2>;
+				reg-io-width = <4>;
+				interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_GATE_UART8CLK>;
+				no-loopback-test;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart8_default>;
+
+				status = "disabled";
+			};
+
+			uart9: serial@1e790300 {
+				compatible = "ns16550a";
+				reg = <0x1e790300 0x20>;
+				reg-shift = <2>;
+				reg-io-width = <4>;
+				interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_GATE_UART9CLK>;
+				no-loopback-test;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart9_default>;
+
+				status = "disabled";
+			};
+
 			i2c: bus@1e78a000 {
 				compatible = "simple-bus";
 				#address-cells = <1>;
@@ -724,22 +844,35 @@
 			};
 
 			fsim0: fsi@1e79b000 {
-				compatible = "aspeed,ast2600-fsi-master", "fsi-master";
+				#interrupt-cells = <1>;
+				compatible = "aspeed,ast2600-fsi-master";
 				reg = <0x1e79b000 0x94>;
 				interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_fsi1_default>;
 				clocks = <&syscon ASPEED_CLK_GATE_FSICLK>;
+				interrupt-controller;
 				status = "disabled";
 			};
 
 			fsim1: fsi@1e79b100 {
-				compatible = "aspeed,ast2600-fsi-master", "fsi-master";
+				#interrupt-cells = <1>;
+				compatible = "aspeed,ast2600-fsi-master";
 				reg = <0x1e79b100 0x94>;
 				interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_fsi2_default>;
 				clocks = <&syscon ASPEED_CLK_GATE_FSICLK>;
+				interrupt-controller;
+				status = "disabled";
+			};
+
+			udma: dma-controller@1e79e000 {
+				compatible = "aspeed,ast2600-udma";
+				reg = <0x1e79e000 0x1000>;
+				interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+				dma-channels = <28>;
+				#dma-cells = <1>;
 				status = "disabled";
 			};
 		};
@@ -749,10 +882,9 @@
 #include "aspeed-g6-pinctrl.dtsi"
 
 &i2c {
-	i2c0: i2c-bus@80 {
+	i2c0: i2c@80 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 		reg = <0x80 0x80>;
 		compatible = "aspeed,ast2600-i2c-bus";
 		clocks = <&syscon ASPEED_CLK_APB2>;
@@ -764,10 +896,9 @@
 		status = "disabled";
 	};
 
-	i2c1: i2c-bus@100 {
+	i2c1: i2c@100 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 		reg = <0x100 0x80>;
 		compatible = "aspeed,ast2600-i2c-bus";
 		clocks = <&syscon ASPEED_CLK_APB2>;
@@ -779,10 +910,9 @@
 		status = "disabled";
 	};
 
-	i2c2: i2c-bus@180 {
+	i2c2: i2c@180 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 		reg = <0x180 0x80>;
 		compatible = "aspeed,ast2600-i2c-bus";
 		clocks = <&syscon ASPEED_CLK_APB2>;
@@ -794,10 +924,9 @@
 		status = "disabled";
 	};
 
-	i2c3: i2c-bus@200 {
+	i2c3: i2c@200 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 		reg = <0x200 0x80>;
 		compatible = "aspeed,ast2600-i2c-bus";
 		clocks = <&syscon ASPEED_CLK_APB2>;
@@ -809,10 +938,9 @@
 		status = "disabled";
 	};
 
-	i2c4: i2c-bus@280 {
+	i2c4: i2c@280 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 		reg = <0x280 0x80>;
 		compatible = "aspeed,ast2600-i2c-bus";
 		clocks = <&syscon ASPEED_CLK_APB2>;
@@ -824,10 +952,9 @@
 		status = "disabled";
 	};
 
-	i2c5: i2c-bus@300 {
+	i2c5: i2c@300 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 		reg = <0x300 0x80>;
 		compatible = "aspeed,ast2600-i2c-bus";
 		clocks = <&syscon ASPEED_CLK_APB2>;
@@ -839,10 +966,9 @@
 		status = "disabled";
 	};
 
-	i2c6: i2c-bus@380 {
+	i2c6: i2c@380 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 		reg = <0x380 0x80>;
 		compatible = "aspeed,ast2600-i2c-bus";
 		clocks = <&syscon ASPEED_CLK_APB2>;
@@ -854,10 +980,9 @@
 		status = "disabled";
 	};
 
-	i2c7: i2c-bus@400 {
+	i2c7: i2c@400 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 		reg = <0x400 0x80>;
 		compatible = "aspeed,ast2600-i2c-bus";
 		clocks = <&syscon ASPEED_CLK_APB2>;
@@ -869,10 +994,9 @@
 		status = "disabled";
 	};
 
-	i2c8: i2c-bus@480 {
+	i2c8: i2c@480 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 		reg = <0x480 0x80>;
 		compatible = "aspeed,ast2600-i2c-bus";
 		clocks = <&syscon ASPEED_CLK_APB2>;
@@ -884,10 +1008,9 @@
 		status = "disabled";
 	};
 
-	i2c9: i2c-bus@500 {
+	i2c9: i2c@500 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 		reg = <0x500 0x80>;
 		compatible = "aspeed,ast2600-i2c-bus";
 		clocks = <&syscon ASPEED_CLK_APB2>;
@@ -899,10 +1022,9 @@
 		status = "disabled";
 	};
 
-	i2c10: i2c-bus@580 {
+	i2c10: i2c@580 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 		reg = <0x580 0x80>;
 		compatible = "aspeed,ast2600-i2c-bus";
 		clocks = <&syscon ASPEED_CLK_APB2>;
@@ -914,10 +1036,9 @@
 		status = "disabled";
 	};
 
-	i2c11: i2c-bus@600 {
+	i2c11: i2c@600 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 		reg = <0x600 0x80>;
 		compatible = "aspeed,ast2600-i2c-bus";
 		clocks = <&syscon ASPEED_CLK_APB2>;
@@ -929,10 +1050,9 @@
 		status = "disabled";
 	};
 
-	i2c12: i2c-bus@680 {
+	i2c12: i2c@680 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 		reg = <0x680 0x80>;
 		compatible = "aspeed,ast2600-i2c-bus";
 		clocks = <&syscon ASPEED_CLK_APB2>;
@@ -944,10 +1064,9 @@
 		status = "disabled";
 	};
 
-	i2c13: i2c-bus@700 {
+	i2c13: i2c@700 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 		reg = <0x700 0x80>;
 		compatible = "aspeed,ast2600-i2c-bus";
 		clocks = <&syscon ASPEED_CLK_APB2>;
@@ -959,10 +1078,9 @@
 		status = "disabled";
 	};
 
-	i2c14: i2c-bus@780 {
+	i2c14: i2c@780 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 		reg = <0x780 0x80>;
 		compatible = "aspeed,ast2600-i2c-bus";
 		clocks = <&syscon ASPEED_CLK_APB2>;
@@ -974,10 +1092,9 @@
 		status = "disabled";
 	};
 
-	i2c15: i2c-bus@800 {
+	i2c15: i2c@800 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		#interrupt-cells = <1>;
 		reg = <0x800 0x80>;
 		compatible = "aspeed,ast2600-i2c-bus";
 		clocks = <&syscon ASPEED_CLK_APB2>;
diff --git a/arch/arm/boot/dts/ast2400-facebook-netbmc-common.dtsi b/arch/arm/boot/dts/aspeed/ast2400-facebook-netbmc-common.dtsi
index 4e5e786e18b7..4e5e786e18b7 100644
--- a/arch/arm/boot/dts/ast2400-facebook-netbmc-common.dtsi
+++ b/arch/arm/boot/dts/aspeed/ast2400-facebook-netbmc-common.dtsi
diff --git a/arch/arm/boot/dts/ast2500-facebook-netbmc-common.dtsi b/arch/arm/boot/dts/aspeed/ast2500-facebook-netbmc-common.dtsi
index c0c43b8644ee..7f1ae3f4df9d 100644
--- a/arch/arm/boot/dts/ast2500-facebook-netbmc-common.dtsi
+++ b/arch/arm/boot/dts/aspeed/ast2500-facebook-netbmc-common.dtsi
@@ -4,6 +4,10 @@
 #include "aspeed-g5.dtsi"
 
 / {
+	aliases {
+		spi0 = &fmc;
+	};
+
 	memory@80000000 {
 		reg = <0x80000000 0x40000000>;
 	};
diff --git a/arch/arm/boot/dts/ast2600-facebook-netbmc-common.dtsi b/arch/arm/boot/dts/aspeed/ast2600-facebook-netbmc-common.dtsi
index 051de5bec345..0ef225acddfc 100644
--- a/arch/arm/boot/dts/ast2600-facebook-netbmc-common.dtsi
+++ b/arch/arm/boot/dts/aspeed/ast2600-facebook-netbmc-common.dtsi
@@ -25,18 +25,22 @@
 	 * full-duplex SPI transactions are not supported by ASPEED SPI
 	 * Controllers.
 	 */
-	spi_gpio: spi-gpio {
+	spi_gpio: spi {
 		status = "okay";
 		compatible = "spi-gpio";
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		gpio-sck = <&gpio0 ASPEED_GPIO(X, 3) GPIO_ACTIVE_HIGH>;
-		gpio-mosi = <&gpio0 ASPEED_GPIO(X, 4) GPIO_ACTIVE_HIGH>;
-		gpio-miso = <&gpio0 ASPEED_GPIO(X, 5) GPIO_ACTIVE_HIGH>;
+		/*
+		 * chipselect pins are defined in platform .dts files
+		 * separately.
+		 */
+		sck-gpios = <&gpio0 ASPEED_GPIO(X, 3) GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio0 ASPEED_GPIO(X, 4) GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpio0 ASPEED_GPIO(X, 5) GPIO_ACTIVE_HIGH>;
 
-		tpmdev@0 {
-			compatible = "tcg,tpm_tis-spi";
+		tpm@0 {
+			compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
 			spi-max-frequency = <33000000>;
 			reg = <0>;
 		};
@@ -152,18 +156,6 @@
 	status = "okay";
 };
 
-&emmc_controller {
-	status = "okay";
-};
-
-&emmc {
-	status = "okay";
-
-	non-removable;
-	max-frequency = <25000000>;
-	bus-width = <4>;
-};
-
 &rtc {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/aspeed/facebook-bmc-flash-layout-128-data64.dtsi b/arch/arm/boot/dts/aspeed/facebook-bmc-flash-layout-128-data64.dtsi
new file mode 100644
index 000000000000..efd92232cda2
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/facebook-bmc-flash-layout-128-data64.dtsi
@@ -0,0 +1,60 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2020 Facebook Inc.
+
+partitions {
+	compatible = "fixed-partitions";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	/*
+	 * u-boot partition: 896KB.
+	 */
+	u-boot@0 {
+		reg = <0x0 0xe0000>;
+		label = "u-boot";
+	};
+
+	/*
+	 * u-boot environment variables: 64KB.
+	 */
+	u-boot-env@e0000 {
+		reg = <0xe0000 0x10000>;
+		label = "env";
+	};
+
+	/*
+	 * image metadata partition (64KB), used by Facebook internal
+	 * tools.
+	 */
+	image-meta@f0000 {
+		reg = <0xf0000 0x10000>;
+		label = "meta";
+	};
+
+	/*
+	 * FIT image: 63 MB.
+	 */
+	fit@100000 {
+		reg = <0x100000 0x3f00000>;
+		label = "fit";
+	};
+
+	/*
+	 * "data0" partition (64MB) is used by Facebook BMC platforms as
+	 * persistent data store.
+	 */
+	data0@4000000 {
+		reg = <0x4000000 0x4000000>;
+		label = "data0";
+	};
+
+	/*
+	 * Although the master partition can be created by enabling
+	 * MTD_PARTITIONED_MASTER option, below "flash0" partition is
+	 * explicitly created to avoid breaking legacy applications.
+	 */
+	flash0@0 {
+		reg = <0x0 0x8000000>;
+		label = "flash0";
+	};
+};
diff --git a/arch/arm/boot/dts/facebook-bmc-flash-layout-128.dtsi b/arch/arm/boot/dts/aspeed/facebook-bmc-flash-layout-128.dtsi
index 7f3652dea550..7f3652dea550 100644
--- a/arch/arm/boot/dts/facebook-bmc-flash-layout-128.dtsi
+++ b/arch/arm/boot/dts/aspeed/facebook-bmc-flash-layout-128.dtsi
diff --git a/arch/arm/boot/dts/facebook-bmc-flash-layout.dtsi b/arch/arm/boot/dts/aspeed/facebook-bmc-flash-layout.dtsi
index 87bb8b576250..87bb8b576250 100644
--- a/arch/arm/boot/dts/facebook-bmc-flash-layout.dtsi
+++ b/arch/arm/boot/dts/aspeed/facebook-bmc-flash-layout.dtsi
diff --git a/arch/arm/boot/dts/aspeed/ibm-power10-dual.dtsi b/arch/arm/boot/dts/aspeed/ibm-power10-dual.dtsi
new file mode 100644
index 000000000000..06fac236773f
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/ibm-power10-dual.dtsi
@@ -0,0 +1,386 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2023 IBM Corp.
+
+&fsim0 {
+	status = "okay";
+
+	#address-cells = <2>;
+	#size-cells = <0>;
+
+	cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_HIGH>;
+
+	cfam@0,0 {
+		reg = <0 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <0>;
+
+		scom@1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,fsi-i2c-master";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam0_i2c0: i2c-bus@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;	/* OMI01 */
+			};
+
+			cfam0_i2c1: i2c-bus@1 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <1>;	/* OMI23 */
+			};
+
+			cfam0_i2c10: i2c-bus@a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+			};
+
+			cfam0_i2c11: i2c-bus@b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+			};
+
+			cfam0_i2c12: i2c-bus@c {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <12>;	/* OP4A */
+			};
+
+			cfam0_i2c13: i2c-bus@d {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <13>;	/* OP4B */
+			};
+
+			cfam0_i2c14: i2c-bus@e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+			};
+
+			cfam0_i2c15: i2c-bus@f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam0_spi0: spi@0 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam0_spi1: spi@20 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam0_spi2: spi@40 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam0_spi3: spi@60 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ0: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub0: hub@3400 {
+			#interrupt-cells = <1>;
+			compatible = "fsi-master-hub";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			interrupt-controller;
+		};
+	};
+};
+
+&fsi_hub0 {
+	cfam@1,0 {
+		reg = <1 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <1>;
+
+		scom@1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,fsi-i2c-master";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam1_i2c2: i2c-bus@2 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <2>;	/* OMI45 */
+			};
+
+			cfam1_i2c3: i2c-bus@3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <3>;	/* OMI67 */
+			};
+
+			cfam1_i2c10: i2c-bus@a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+			};
+
+			cfam1_i2c11: i2c-bus@b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+			};
+
+			cfam1_i2c14: i2c-bus@e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+			};
+
+			cfam1_i2c15: i2c-bus@f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+			};
+
+			cfam1_i2c16: i2c-bus@10 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <16>;	/* OP6A */
+			};
+
+			cfam1_i2c17: i2c-bus@11 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <17>;	/* OP6B */
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam1_spi0: spi@0 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam1_spi1: spi@20 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam1_spi2: spi@40 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam1_spi3: spi@60 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ1: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub1: hub@3400 {
+			compatible = "fsi-master-hub";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			no-scan-on-init;
+		};
+	};
+};
+
+/* Legacy OCC numbering (to get rid of when userspace is fixed) */
+&fsi_occ0 {
+	reg = <1>;
+};
+
+&fsi_occ1 {
+	reg = <2>;
+};
+
+/ {
+	aliases {
+		i2c100 = &cfam0_i2c0;
+		i2c101 = &cfam0_i2c1;
+		i2c110 = &cfam0_i2c10;
+		i2c111 = &cfam0_i2c11;
+		i2c112 = &cfam0_i2c12;
+		i2c113 = &cfam0_i2c13;
+		i2c114 = &cfam0_i2c14;
+		i2c115 = &cfam0_i2c15;
+		i2c202 = &cfam1_i2c2;
+		i2c203 = &cfam1_i2c3;
+		i2c210 = &cfam1_i2c10;
+		i2c211 = &cfam1_i2c11;
+		i2c214 = &cfam1_i2c14;
+		i2c215 = &cfam1_i2c15;
+		i2c216 = &cfam1_i2c16;
+		i2c217 = &cfam1_i2c17;
+
+		spi10 = &cfam0_spi0;
+		spi11 = &cfam0_spi1;
+		spi12 = &cfam0_spi2;
+		spi13 = &cfam0_spi3;
+		spi20 = &cfam1_spi0;
+		spi21 = &cfam1_spi1;
+		spi22 = &cfam1_spi2;
+		spi23 = &cfam1_spi3;
+	};
+};
diff --git a/arch/arm/boot/dts/aspeed/ibm-power10-quad.dtsi b/arch/arm/boot/dts/aspeed/ibm-power10-quad.dtsi
new file mode 100644
index 000000000000..9501f66d0030
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/ibm-power10-quad.dtsi
@@ -0,0 +1,1309 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2023 IBM Corp.
+
+#include "ibm-power10-dual.dtsi"
+
+&cfam0_i2c0 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom100: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo100: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c1 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom101: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo101: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c10 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom110: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo110: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c11 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom111: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo111: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c12 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom112: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo112: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c13 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom113: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo113: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c14 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom114: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo114: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam0_i2c15 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom115: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo115: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c2 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom202: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo202: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c3 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom203: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo203: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c10 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom210: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo210: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c11 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom211: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo211: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c14 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom214: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo214: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c15 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom215: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo215: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c16 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom216: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo216: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&cfam1_i2c17 {
+	i2cr@20 {
+		compatible = "ibm,i2cr-fsi-master";
+		reg = <0x20>;
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cfam@0,0 {
+			reg = <0 0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			chip-id = <0>;
+
+			scom217: scom@1000 {
+				compatible = "ibm,i2cr-scom";
+				reg = <0x1000 0x400>;
+			};
+
+			sbefifo217: sbefifo@2400 {
+				compatible = "ibm,p9-sbefifo";
+				reg = <0x2400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+};
+
+&fsi_hub0 {
+	cfam@2,0 {
+		reg = <2 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <2>;
+
+		scom@1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,fsi-i2c-master";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam2_i2c0: i2c-bus@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;	/* OM01 */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom300: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo300: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam2_i2c1: i2c-bus@1 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <1>;	/* OM23 */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom301: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo301: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam2_i2c10: i2c-bus@a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom310: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo310: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam2_i2c11: i2c-bus@b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom311: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo311: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam2_i2c12: i2c-bus@c {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <12>;	/* OP4A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom312: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo312: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam2_i2c13: i2c-bus@d {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <13>;	/* OP4B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom313: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo313: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam2_i2c14: i2c-bus@e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom314: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo314: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam2_i2c15: i2c-bus@f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom315: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo315: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam2_spi0: spi@0 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam2_spi1: spi@20 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam2_spi2: spi@40 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam2_spi3: spi@60 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ2: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub2: hub@3400 {
+			compatible = "fsi-master-hub";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			no-scan-on-init;
+		};
+	};
+
+	cfam@3,0 {
+		reg = <3 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <3>;
+
+		scom@1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,fsi-i2c-master";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam3_i2c2: i2c-bus@2 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <2>;	/* OM45 */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom402: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo402: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam3_i2c3: i2c-bus@3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <3>;	/* OM67 */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom403: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo403: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam3_i2c10: i2c-bus@a {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <10>;	/* OP3A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom410: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo410: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam3_i2c11: i2c-bus@b {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <11>;	/* OP3B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom411: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo411: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam3_i2c14: i2c-bus@e {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <14>;	/* OP5A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom414: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo414: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam3_i2c15: i2c-bus@f {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <15>;	/* OP5B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom415: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo415: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam3_i2c16: i2c-bus@10 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <16>;	/* OP6A */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom416: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo416: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+
+			cfam3_i2c17: i2c-bus@11 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <17>;	/* OP6B */
+
+				i2cr@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom417: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo417: sbefifo@2400 {
+							compatible = "ibm,p9-sbefifo";
+							reg = <0x2400 0x400>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+						};
+					};
+				};
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam3_spi0: spi@0 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam3_spi1: spi@20 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam3_spi2: spi@40 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam3_spi3: spi@60 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ3: occ {
+				compatible = "ibm,p10-occ";
+
+				occ-hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub3: hub@3400 {
+			compatible = "fsi-master-hub";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			no-scan-on-init;
+		};
+	};
+};
+
+/* Legacy OCC numbering (to get rid of when userspace is fixed) */
+&fsi_occ2 {
+	reg = <3>;
+};
+
+&fsi_occ3 {
+	reg = <4>;
+};
+
+/ {
+	aliases {
+		i2c300 = &cfam2_i2c0;
+		i2c301 = &cfam2_i2c1;
+		i2c310 = &cfam2_i2c10;
+		i2c311 = &cfam2_i2c11;
+		i2c312 = &cfam2_i2c12;
+		i2c313 = &cfam2_i2c13;
+		i2c314 = &cfam2_i2c14;
+		i2c315 = &cfam2_i2c15;
+		i2c402 = &cfam3_i2c2;
+		i2c403 = &cfam3_i2c3;
+		i2c410 = &cfam3_i2c10;
+		i2c411 = &cfam3_i2c11;
+		i2c414 = &cfam3_i2c14;
+		i2c415 = &cfam3_i2c15;
+		i2c416 = &cfam3_i2c16;
+		i2c417 = &cfam3_i2c17;
+
+		sbefifo100 = &sbefifo100;
+		sbefifo101 = &sbefifo101;
+		sbefifo110 = &sbefifo110;
+		sbefifo111 = &sbefifo111;
+		sbefifo112 = &sbefifo112;
+		sbefifo113 = &sbefifo113;
+		sbefifo114 = &sbefifo114;
+		sbefifo115 = &sbefifo115;
+		sbefifo202 = &sbefifo202;
+		sbefifo203 = &sbefifo203;
+		sbefifo210 = &sbefifo210;
+		sbefifo211 = &sbefifo211;
+		sbefifo214 = &sbefifo214;
+		sbefifo215 = &sbefifo215;
+		sbefifo216 = &sbefifo216;
+		sbefifo217 = &sbefifo217;
+		sbefifo300 = &sbefifo300;
+		sbefifo301 = &sbefifo301;
+		sbefifo310 = &sbefifo310;
+		sbefifo311 = &sbefifo311;
+		sbefifo312 = &sbefifo312;
+		sbefifo313 = &sbefifo313;
+		sbefifo314 = &sbefifo314;
+		sbefifo315 = &sbefifo315;
+		sbefifo402 = &sbefifo402;
+		sbefifo403 = &sbefifo403;
+		sbefifo410 = &sbefifo410;
+		sbefifo411 = &sbefifo411;
+		sbefifo414 = &sbefifo414;
+		sbefifo415 = &sbefifo415;
+		sbefifo416 = &sbefifo416;
+		sbefifo417 = &sbefifo417;
+
+		scom100 = &scom100;
+		scom101 = &scom101;
+		scom110 = &scom110;
+		scom111 = &scom111;
+		scom112 = &scom112;
+		scom113 = &scom113;
+		scom114 = &scom114;
+		scom115 = &scom115;
+		scom202 = &scom202;
+		scom203 = &scom203;
+		scom210 = &scom210;
+		scom211 = &scom211;
+		scom214 = &scom214;
+		scom215 = &scom215;
+		scom216 = &scom216;
+		scom217 = &scom217;
+		scom300 = &scom300;
+		scom301 = &scom301;
+		scom310 = &scom310;
+		scom311 = &scom311;
+		scom312 = &scom312;
+		scom313 = &scom313;
+		scom314 = &scom314;
+		scom315 = &scom315;
+		scom402 = &scom402;
+		scom403 = &scom403;
+		scom410 = &scom410;
+		scom411 = &scom411;
+		scom414 = &scom414;
+		scom415 = &scom415;
+		scom416 = &scom416;
+		scom417 = &scom417;
+
+		spi30 = &cfam2_spi0;
+		spi31 = &cfam2_spi1;
+		spi32 = &cfam2_spi2;
+		spi33 = &cfam2_spi3;
+		spi40 = &cfam3_spi0;
+		spi41 = &cfam3_spi1;
+		spi42 = &cfam3_spi2;
+		spi43 = &cfam3_spi3;
+	};
+};
diff --git a/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi b/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
new file mode 100644
index 000000000000..68c941a194b6
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/ibm-power11-quad.dtsi
@@ -0,0 +1,1539 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2024 IBM Corp.
+
+/ {
+	aliases {
+		i2c100 = &cfam0_i2c0;
+		i2c101 = &cfam0_i2c1;
+		i2c110 = &cfam0_i2c10;
+		i2c111 = &cfam0_i2c11;
+		i2c112 = &cfam0_i2c12;
+		i2c113 = &cfam0_i2c13;
+		i2c114 = &cfam0_i2c14;
+		i2c115 = &cfam0_i2c15;
+		i2c202 = &cfam1_i2c2;
+		i2c203 = &cfam1_i2c3;
+		i2c210 = &cfam1_i2c10;
+		i2c211 = &cfam1_i2c11;
+		i2c214 = &cfam1_i2c14;
+		i2c215 = &cfam1_i2c15;
+		i2c216 = &cfam1_i2c16;
+		i2c217 = &cfam1_i2c17;
+		i2c300 = &cfam2_i2c0;
+		i2c301 = &cfam2_i2c1;
+		i2c310 = &cfam2_i2c10;
+		i2c311 = &cfam2_i2c11;
+		i2c312 = &cfam2_i2c12;
+		i2c313 = &cfam2_i2c13;
+		i2c314 = &cfam2_i2c14;
+		i2c315 = &cfam2_i2c15;
+		i2c402 = &cfam3_i2c2;
+		i2c403 = &cfam3_i2c3;
+		i2c410 = &cfam3_i2c10;
+		i2c411 = &cfam3_i2c11;
+		i2c414 = &cfam3_i2c14;
+		i2c415 = &cfam3_i2c15;
+		i2c416 = &cfam3_i2c16;
+		i2c417 = &cfam3_i2c17;
+
+		sbefifo100 = &sbefifo100;
+		sbefifo101 = &sbefifo101;
+		sbefifo110 = &sbefifo110;
+		sbefifo111 = &sbefifo111;
+		sbefifo112 = &sbefifo112;
+		sbefifo113 = &sbefifo113;
+		sbefifo114 = &sbefifo114;
+		sbefifo115 = &sbefifo115;
+		sbefifo202 = &sbefifo202;
+		sbefifo203 = &sbefifo203;
+		sbefifo210 = &sbefifo210;
+		sbefifo211 = &sbefifo211;
+		sbefifo214 = &sbefifo214;
+		sbefifo215 = &sbefifo215;
+		sbefifo216 = &sbefifo216;
+		sbefifo217 = &sbefifo217;
+		sbefifo300 = &sbefifo300;
+		sbefifo301 = &sbefifo301;
+		sbefifo310 = &sbefifo310;
+		sbefifo311 = &sbefifo311;
+		sbefifo312 = &sbefifo312;
+		sbefifo313 = &sbefifo313;
+		sbefifo314 = &sbefifo314;
+		sbefifo315 = &sbefifo315;
+		sbefifo402 = &sbefifo402;
+		sbefifo403 = &sbefifo403;
+		sbefifo410 = &sbefifo410;
+		sbefifo411 = &sbefifo411;
+		sbefifo414 = &sbefifo414;
+		sbefifo415 = &sbefifo415;
+		sbefifo416 = &sbefifo416;
+		sbefifo417 = &sbefifo417;
+
+		scom100 = &scom100;
+		scom101 = &scom101;
+		scom110 = &scom110;
+		scom111 = &scom111;
+		scom112 = &scom112;
+		scom113 = &scom113;
+		scom114 = &scom114;
+		scom115 = &scom115;
+		scom202 = &scom202;
+		scom203 = &scom203;
+		scom210 = &scom210;
+		scom211 = &scom211;
+		scom214 = &scom214;
+		scom215 = &scom215;
+		scom216 = &scom216;
+		scom217 = &scom217;
+		scom300 = &scom300;
+		scom301 = &scom301;
+		scom310 = &scom310;
+		scom311 = &scom311;
+		scom312 = &scom312;
+		scom313 = &scom313;
+		scom314 = &scom314;
+		scom315 = &scom315;
+		scom402 = &scom402;
+		scom403 = &scom403;
+		scom410 = &scom410;
+		scom411 = &scom411;
+		scom414 = &scom414;
+		scom415 = &scom415;
+		scom416 = &scom416;
+		scom417 = &scom417;
+
+		spi10 = &cfam0_spi0;
+		spi11 = &cfam0_spi1;
+		spi12 = &cfam0_spi2;
+		spi13 = &cfam0_spi3;
+		spi20 = &cfam1_spi0;
+		spi21 = &cfam1_spi1;
+		spi22 = &cfam1_spi2;
+		spi23 = &cfam1_spi3;
+		spi30 = &cfam2_spi0;
+		spi31 = &cfam2_spi1;
+		spi32 = &cfam2_spi2;
+		spi33 = &cfam2_spi3;
+		spi40 = &cfam3_spi0;
+		spi41 = &cfam3_spi1;
+		spi42 = &cfam3_spi2;
+		spi43 = &cfam3_spi3;
+	};
+};
+
+&fsim0 {
+	#address-cells = <2>;
+	#size-cells = <0>;
+	status = "okay";
+	bus-frequency = <100000000>;
+	cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_HIGH>;
+
+	cfam@0,0 {
+		reg = <0 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <0>;
+
+		scom@1000 {
+			compatible = "ibm,p9-scom";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,i2c-fsi";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam0_i2c0: i2c-bus@0 {
+				reg = <0>;	/* OMI01 */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom100: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo100: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam0_i2c1: i2c-bus@1 {
+				reg = <1>;	/* OMI23 */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom101: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo101: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam0_i2c10: i2c-bus@a {
+				reg = <10>;	/* OP3A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom110: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo110: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam0_i2c11: i2c-bus@b {
+				reg = <11>;	/* OP3B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom111: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo111: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam0_i2c12: i2c-bus@c {
+				reg = <12>;	/* OP4A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom112: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo112: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam0_i2c13: i2c-bus@d {
+				reg = <13>;	/* OP4B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom113: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo113: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam0_i2c14: i2c-bus@e {
+				reg = <14>;	/* OP5A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom114: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo114: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam0_i2c15: i2c-bus@f {
+				reg = <15>;	/* OP5B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom115: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo115: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam0_spi0: spi@0 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam0_spi1: spi@20 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam0_spi2: spi@40 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam0_spi3: spi@60 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+
+			occ {
+				compatible = "ibm,p10-occ";
+
+				hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi_hub0: fsi@3400 {
+			compatible = "ibm,p9-fsi-controller";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&fsi_hub0 {
+	cfam@1,0 {
+		reg = <1 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <1>;
+
+		scom@1000 {
+			compatible = "ibm,p9-scom";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,i2c-fsi";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam1_i2c2: i2c-bus@2 {
+				reg = <2>;	/* OMI45 */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom202: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo202: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam1_i2c3: i2c-bus@3 {
+				reg = <3>;	/* OMI67 */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom203: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo203: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam1_i2c10: i2c-bus@a {
+				reg = <10>;	/* OP3A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom210: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo210: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam1_i2c11: i2c-bus@b {
+				reg = <11>;	/* OP3B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom211: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo211: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam1_i2c14: i2c-bus@e {
+				reg = <14>;	/* OP5A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom214: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo214: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam1_i2c15: i2c-bus@f {
+				reg = <15>;	/* OP5B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom215: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo215: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam1_i2c16: i2c-bus@10 {
+				reg = <16>;	/* OP6A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom216: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo216: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam1_i2c17: i2c-bus@11 {
+				reg = <17>;	/* OP6B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom217: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo217: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam1_spi0: spi@0 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam1_spi1: spi@20 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam1_spi2: spi@40 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam1_spi3: spi@60 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+
+			occ {
+				compatible = "ibm,p10-occ";
+
+				hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi@3400 {
+			compatible = "ibm,p9-fsi-controller";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			no-scan-on-init;
+		};
+	};
+
+	cfam@2,0 {
+		reg = <2 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <2>;
+
+		scom@1000 {
+			compatible = "ibm,p9-scom";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,i2c-fsi";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam2_i2c0: i2c-bus@0 {
+				reg = <0>;	/* OM01 */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom300: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo300: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam2_i2c1: i2c-bus@1 {
+				reg = <1>;	/* OM23 */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom301: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo301: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam2_i2c10: i2c-bus@a {
+				reg = <10>;	/* OP3A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom310: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo310: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam2_i2c11: i2c-bus@b {
+				reg = <11>;	/* OP3B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom311: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo311: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam2_i2c12: i2c-bus@c {
+				reg = <12>;	/* OP4A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom312: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo312: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam2_i2c13: i2c-bus@d {
+				reg = <13>;	/* OP4B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom313: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo313: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam2_i2c14: i2c-bus@e {
+				reg = <14>;	/* OP5A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom314: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo314: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam2_i2c15: i2c-bus@f {
+				reg = <15>;	/* OP5B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom315: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo315: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam2_spi0: spi@0 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam2_spi1: spi@20 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam2_spi2: spi@40 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam2_spi3: spi@60 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+
+			occ {
+				compatible = "ibm,p10-occ";
+
+				hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi@3400 {
+			compatible = "ibm,p9-fsi-controller";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			no-scan-on-init;
+		};
+	};
+
+	cfam@3,0 {
+		reg = <3 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <3>;
+
+		scom@1000 {
+			compatible = "ibm,p9-scom";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,i2c-fsi";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam3_i2c2: i2c-bus@2 {
+				reg = <2>;	/* OM45 */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom402: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo402: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam3_i2c3: i2c-bus@3 {
+				reg = <3>;	/* OM67 */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom403: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo403: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam3_i2c10: i2c-bus@a {
+				reg = <10>;	/* OP3A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom410: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo410: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam3_i2c11: i2c-bus@b {
+				reg = <11>;	/* OP3B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom411: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo411: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam3_i2c14: i2c-bus@e {
+				reg = <14>;	/* OP5A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom414: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo414: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam3_i2c15: i2c-bus@f {
+				reg = <15>;	/* OP5B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom415: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo415: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam3_i2c16: i2c-bus@10 {
+				reg = <16>;	/* OP6A */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom416: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo416: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+
+			cfam3_i2c17: i2c-bus@11 {
+				reg = <17>;	/* OP6B */
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fsi@20 {
+					compatible = "ibm,i2cr-fsi-master";
+					reg = <0x20>;
+					#address-cells = <2>;
+					#size-cells = <0>;
+
+					cfam@0,0 {
+						reg = <0 0>;
+						#address-cells = <1>;
+						#size-cells = <1>;
+						chip-id = <0>;
+
+						scom417: scom@1000 {
+							compatible = "ibm,i2cr-scom";
+							reg = <0x1000 0x400>;
+						};
+
+						sbefifo417: sbefifo@2400 {
+							compatible = "ibm,odyssey-sbefifo";
+							reg = <0x2400 0x400>;
+						};
+					};
+				};
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam3_spi0: spi@0 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam3_spi1: spi@20 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam3_spi2: spi@40 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x40>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			cfam3_spi3: spi@60 {
+				compatible = "ibm,spi-fsi";
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					compatible = "atmel,at25";
+					reg = <0>;
+					address-width = <24>;
+					pagesize = <256>;
+					size = <0x80000>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+
+			occ {
+				compatible = "ibm,p10-occ";
+
+				hwmon {
+					compatible = "ibm,p10-occ-hwmon";
+					ibm,no-poll-on-init;
+				};
+			};
+		};
+
+		fsi@3400 {
+			compatible = "ibm,p9-fsi-controller";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			no-scan-on-init;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/ibm-power9-dual.dtsi b/arch/arm/boot/dts/aspeed/ibm-power9-dual.dtsi
index a0fa65b44b0f..a0fa65b44b0f 100644
--- a/arch/arm/boot/dts/ibm-power9-dual.dtsi
+++ b/arch/arm/boot/dts/aspeed/ibm-power9-dual.dtsi
diff --git a/arch/arm/boot/dts/openbmc-flash-layout-128.dtsi b/arch/arm/boot/dts/aspeed/openbmc-flash-layout-128.dtsi
index 05101a38c5bd..05101a38c5bd 100644
--- a/arch/arm/boot/dts/openbmc-flash-layout-128.dtsi
+++ b/arch/arm/boot/dts/aspeed/openbmc-flash-layout-128.dtsi
diff --git a/arch/arm/boot/dts/openbmc-flash-layout-64-alt.dtsi b/arch/arm/boot/dts/aspeed/openbmc-flash-layout-64-alt.dtsi
index 650525867561..650525867561 100644
--- a/arch/arm/boot/dts/openbmc-flash-layout-64-alt.dtsi
+++ b/arch/arm/boot/dts/aspeed/openbmc-flash-layout-64-alt.dtsi
diff --git a/arch/arm/boot/dts/openbmc-flash-layout-64.dtsi b/arch/arm/boot/dts/aspeed/openbmc-flash-layout-64.dtsi
index 7af41361c480..7af41361c480 100644
--- a/arch/arm/boot/dts/openbmc-flash-layout-64.dtsi
+++ b/arch/arm/boot/dts/aspeed/openbmc-flash-layout-64.dtsi
diff --git a/arch/arm/boot/dts/openbmc-flash-layout.dtsi b/arch/arm/boot/dts/aspeed/openbmc-flash-layout.dtsi
index b47e14063c38..b47e14063c38 100644
--- a/arch/arm/boot/dts/openbmc-flash-layout.dtsi
+++ b/arch/arm/boot/dts/aspeed/openbmc-flash-layout.dtsi
diff --git a/arch/arm/boot/dts/axis/Makefile b/arch/arm/boot/dts/axis/Makefile
new file mode 100644
index 000000000000..2cab41451281
--- /dev/null
+++ b/arch/arm/boot/dts/axis/Makefile
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_MACH_ARTPEC6) += \
+	artpec6-devboard.dtb
+dtb-$(CONFIG_MACH_ARTPEC6) += \
+	artpec6-devboard.dtb
diff --git a/arch/arm/boot/dts/artpec6-devboard.dts b/arch/arm/boot/dts/axis/artpec6-devboard.dts
index d20d95359b28..042a9cc920c6 100644
--- a/arch/arm/boot/dts/artpec6-devboard.dts
+++ b/arch/arm/boot/dts/axis/artpec6-devboard.dts
@@ -1,10 +1,5 @@
-/*
- * Axis ARTPEC-6 development board.
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Axis ARTPEC-6 development board.
 
 /dts-v1/;
 #include "artpec6.dtsi"
diff --git a/arch/arm/boot/dts/artpec6.dtsi b/arch/arm/boot/dts/axis/artpec6.dtsi
index 037157e6c5ee..037157e6c5ee 100644
--- a/arch/arm/boot/dts/artpec6.dtsi
+++ b/arch/arm/boot/dts/axis/artpec6.dtsi
diff --git a/arch/arm/boot/dts/bcm21664-garnet.dts b/arch/arm/boot/dts/bcm21664-garnet.dts
deleted file mode 100644
index be468f4adc37..000000000000
--- a/arch/arm/boot/dts/bcm21664-garnet.dts
+++ /dev/null
@@ -1,57 +0,0 @@
-/*
- * Copyright (C) 2014 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-/dts-v1/;
-
-#include <dt-bindings/gpio/gpio.h>
-
-#include "bcm21664.dtsi"
-
-/ {
-	model = "BCM21664 Garnet board";
-	compatible = "brcm,bcm21664-garnet", "brcm,bcm21664";
-
-	memory@80000000 {
-		device_type = "memory";
-		reg = <0x80000000 0x40000000>; /* 1 GB */
-	};
-
-	uart@3e000000 {
-		status = "okay";
-	};
-
-	sdio1: sdio@3f180000 {
-		max-frequency = <48000000>;
-		status = "okay";
-	};
-
-	sdio2: sdio@3f190000 {
-		non-removable;
-		max-frequency = <48000000>;
-		status = "okay";
-	};
-
-	sdio4: sdio@3f1b0000 {
-		max-frequency = <48000000>;
-		cd-gpios = <&gpio 91 GPIO_ACTIVE_LOW>;
-		status = "okay";
-	};
-
-	usbotg: usb@3f120000 {
-		status = "okay";
-	};
-
-	usbphy: usb-phy@3f130000 {
-		status = "okay";
-	};
-};
diff --git a/arch/arm/boot/dts/bcm21664.dtsi b/arch/arm/boot/dts/bcm21664.dtsi
deleted file mode 100644
index cc58f2b926b9..000000000000
--- a/arch/arm/boot/dts/bcm21664.dtsi
+++ /dev/null
@@ -1,357 +0,0 @@
-/*
- * Copyright (C) 2014 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-
-#include "dt-bindings/clock/bcm21664.h"
-
-/ {
-	#address-cells = <1>;
-	#size-cells = <1>;
-	model = "BCM21664 SoC";
-	compatible = "brcm,bcm21664";
-	interrupt-parent = <&gic>;
-
-	chosen {
-		bootargs = "console=ttyS0,115200n8";
-	};
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu0: cpu@0 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a9";
-			reg = <0>;
-		};
-
-		cpu1: cpu@1 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a9";
-			enable-method = "brcm,bcm11351-cpu-method";
-			secondary-boot-reg = <0x35004178>;
-			reg = <1>;
-		};
-	};
-
-	gic: interrupt-controller@3ff00100 {
-		compatible = "arm,cortex-a9-gic";
-		#interrupt-cells = <3>;
-		#address-cells = <0>;
-		interrupt-controller;
-		reg = <0x3ff01000 0x1000>,
-		      <0x3ff00100 0x100>;
-	};
-
-	smc@3404e000 {
-		compatible = "brcm,bcm21664-smc", "brcm,kona-smc";
-		reg = <0x3404e000 0x400>; /* 1 KiB in SRAM */
-	};
-
-	uart@3e000000 {
-		compatible = "brcm,bcm21664-dw-apb-uart", "snps,dw-apb-uart";
-		status = "disabled";
-		reg = <0x3e000000 0x118>;
-		clocks = <&slave_ccu BCM21664_SLAVE_CCU_UARTB>;
-		interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
-		reg-shift = <2>;
-		reg-io-width = <4>;
-	};
-
-	uart@3e001000 {
-		compatible = "brcm,bcm21664-dw-apb-uart", "snps,dw-apb-uart";
-		status = "disabled";
-		reg = <0x3e001000 0x118>;
-		clocks = <&slave_ccu BCM21664_SLAVE_CCU_UARTB2>;
-		interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
-		reg-shift = <2>;
-		reg-io-width = <4>;
-	};
-
-	uart@3e002000 {
-		compatible = "brcm,bcm21664-dw-apb-uart", "snps,dw-apb-uart";
-		status = "disabled";
-		reg = <0x3e002000 0x118>;
-		clocks = <&slave_ccu BCM21664_SLAVE_CCU_UARTB3>;
-		interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
-		reg-shift = <2>;
-		reg-io-width = <4>;
-	};
-
-	L2: cache-controller@3ff20000 {
-		compatible = "arm,pl310-cache";
-		reg = <0x3ff20000 0x1000>;
-		cache-unified;
-		cache-level = <2>;
-	};
-
-	brcm,resetmgr@35001f00 {
-		compatible = "brcm,bcm21664-resetmgr";
-		reg = <0x35001f00 0x24>;
-	};
-
-	timer@35006000 {
-		compatible = "brcm,kona-timer";
-		reg = <0x35006000 0x1c>;
-		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&aon_ccu BCM21664_AON_CCU_HUB_TIMER>;
-	};
-
-	gpio: gpio@35003000 {
-		compatible = "brcm,bcm21664-gpio", "brcm,kona-gpio";
-		reg = <0x35003000 0x524>;
-		interrupts =
-		       <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH
-			GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH
-			GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH
-			GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
-		#gpio-cells = <2>;
-		#interrupt-cells = <2>;
-		gpio-controller;
-		interrupt-controller;
-	};
-
-	sdio1: sdio@3f180000 {
-		compatible = "brcm,kona-sdhci";
-		reg = <0x3f180000 0x801c>;
-		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&master_ccu BCM21664_MASTER_CCU_SDIO1>;
-		status = "disabled";
-	};
-
-	sdio2: sdio@3f190000 {
-		compatible = "brcm,kona-sdhci";
-		reg = <0x3f190000 0x801c>;
-		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&master_ccu BCM21664_MASTER_CCU_SDIO2>;
-		status = "disabled";
-	};
-
-	sdio3: sdio@3f1a0000 {
-		compatible = "brcm,kona-sdhci";
-		reg = <0x3f1a0000 0x801c>;
-		interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&master_ccu BCM21664_MASTER_CCU_SDIO3>;
-		status = "disabled";
-	};
-
-	sdio4: sdio@3f1b0000 {
-		compatible = "brcm,kona-sdhci";
-		reg = <0x3f1b0000 0x801c>;
-		interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&master_ccu BCM21664_MASTER_CCU_SDIO4>;
-		status = "disabled";
-	};
-
-	i2c@3e016000 {
-		compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c";
-		reg = <0x3e016000 0x70>;
-		interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		clocks = <&slave_ccu BCM21664_SLAVE_CCU_BSC1>;
-		status = "disabled";
-	};
-
-	i2c@3e017000 {
-		compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c";
-		reg = <0x3e017000 0x70>;
-		interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		clocks = <&slave_ccu BCM21664_SLAVE_CCU_BSC2>;
-		status = "disabled";
-	};
-
-	i2c@3e018000 {
-		compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c";
-		reg = <0x3e018000 0x70>;
-		interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		clocks = <&slave_ccu BCM21664_SLAVE_CCU_BSC3>;
-		status = "disabled";
-	};
-
-	i2c@3e01c000 {
-		compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c";
-		reg = <0x3e01c000 0x70>;
-		interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		clocks = <&slave_ccu BCM21664_SLAVE_CCU_BSC4>;
-		status = "disabled";
-	};
-
-	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		/*
-		 * Fixed clocks are defined before CCUs whose
-		 * clocks may depend on them.
-		 */
-
-		ref_32k_clk: ref_32k {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <32768>;
-		};
-
-		bbl_32k_clk: bbl_32k {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <32768>;
-		};
-
-		ref_13m_clk: ref_13m {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <13000000>;
-		};
-
-		var_13m_clk: var_13m {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <13000000>;
-		};
-
-		dft_19_5m_clk: dft_19_5m {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <19500000>;
-		};
-
-		ref_crystal_clk: ref_crystal {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <26000000>;
-		};
-
-		ref_52m_clk: ref_52m {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <52000000>;
-		};
-
-		var_52m_clk: var_52m {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <52000000>;
-		};
-
-		usb_otg_ahb_clk: usb_otg_ahb {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <52000000>;
-		};
-
-		ref_96m_clk: ref_96m {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <96000000>;
-		};
-
-		var_96m_clk: var_96m {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <96000000>;
-		};
-
-		ref_104m_clk: ref_104m {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <104000000>;
-		};
-
-		var_104m_clk: var_104m {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <104000000>;
-		};
-
-		ref_156m_clk: ref_156m {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <156000000>;
-		};
-
-		var_156m_clk: var_156m {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <156000000>;
-		};
-
-		root_ccu: root_ccu@35001000 {
-			compatible = BCM21664_DT_ROOT_CCU_COMPAT;
-			reg = <0x35001000 0x0f00>;
-			#clock-cells = <1>;
-			clock-output-names = "frac_1m";
-		};
-
-		aon_ccu: aon_ccu@35002000 {
-			compatible = BCM21664_DT_AON_CCU_COMPAT;
-			reg = <0x35002000 0x0f00>;
-			#clock-cells = <1>;
-			clock-output-names = "hub_timer";
-		};
-
-		master_ccu: master_ccu@3f001000 {
-			compatible = BCM21664_DT_MASTER_CCU_COMPAT;
-			reg = <0x3f001000 0x0f00>;
-			#clock-cells = <1>;
-			clock-output-names = "sdio1",
-					     "sdio2",
-					     "sdio3",
-					     "sdio4",
-					     "sdio1_sleep",
-					     "sdio2_sleep",
-					     "sdio3_sleep",
-					     "sdio4_sleep";
-		};
-
-		slave_ccu: slave_ccu@3e011000 {
-			compatible = BCM21664_DT_SLAVE_CCU_COMPAT;
-			reg = <0x3e011000 0x0f00>;
-			#clock-cells = <1>;
-			clock-output-names = "uartb",
-					     "uartb2",
-					     "uartb3",
-					     "bsc1",
-					     "bsc2",
-					     "bsc3",
-					     "bsc4";
-		};
-	};
-
-	usbotg: usb@3f120000 {
-		compatible = "snps,dwc2";
-		reg = <0x3f120000 0x10000>;
-		interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&usb_otg_ahb_clk>;
-		clock-names = "otg";
-		phys = <&usbphy>;
-		phy-names = "usb2-phy";
-		status = "disabled";
-	};
-
-	usbphy: usb-phy@3f130000 {
-		compatible = "brcm,kona-usb2-phy";
-		reg = <0x3f130000 0x28>;
-		#phy-cells = <0>;
-		status = "disabled";
-	};
-};
diff --git a/arch/arm/boot/dts/bcm28155-ap.dts b/arch/arm/boot/dts/bcm28155-ap.dts
deleted file mode 100644
index ead6e9804dbf..000000000000
--- a/arch/arm/boot/dts/bcm28155-ap.dts
+++ /dev/null
@@ -1,122 +0,0 @@
-/*
- * Copyright (C) 2013 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-/dts-v1/;
-
-#include <dt-bindings/gpio/gpio.h>
-
-#include "bcm11351.dtsi"
-
-/ {
-	model = "BCM28155 AP board";
-	compatible = "brcm,bcm28155-ap", "brcm,bcm11351";
-
-	memory@80000000 {
-		device_type = "memory";
-		reg = <0x80000000 0x40000000>; /* 1 GB */
-	};
-
-	uart@3e000000 {
-		status = "okay";
-	};
-
-	i2c@3e016000 {
-		status="okay";
-		clock-frequency = <400000>;
-	};
-
-	i2c@3e017000 {
-		status="okay";
-		clock-frequency = <400000>;
-	};
-
-	i2c@3e018000 {
-		status="okay";
-		clock-frequency = <400000>;
-	};
-
-	i2c@3500d000 {
-		status="okay";
-		clock-frequency = <100000>;
-
-		pmu: pmu@8 {
-			reg = <0x08>;
-		};
-	};
-
-	sdio2: sdio@3f190000 {
-		non-removable;
-		max-frequency = <48000000>;
-		vmmc-supply = <&camldo1_reg>;
-		vqmmc-supply = <&iosr1_reg>;
-		status = "okay";
-	};
-
-	sdio4: sdio@3f1b0000 {
-		max-frequency = <48000000>;
-		cd-gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
-		vmmc-supply = <&sdldo_reg>;
-		vqmmc-supply = <&sdxldo_reg>;
-		status = "okay";
-	};
-
-	pwm: pwm@3e01a000 {
-		status = "okay";
-	};
-
-	usbotg: usb@3f120000 {
-		vusb_d-supply = <&usbldo_reg>;
-		vusb_a-supply = <&iosr1_reg>;
-		status = "okay";
-	};
-
-	usbphy: usb-phy@3f130000 {
-		status = "okay";
-	};
-};
-
-#include "bcm59056.dtsi"
-
-&pmu {
-	compatible = "brcm,bcm59056";
-	interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
-	regulators {
-		camldo1_reg: camldo1 {
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-		sdldo_reg: sdldo {
-			regulator-min-microvolt = <3000000>;
-			regulator-max-microvolt = <3000000>;
-		};
-
-		sdxldo_reg: sdxldo {
-			regulator-min-microvolt = <2700000>;
-			regulator-max-microvolt = <3300000>;
-		};
-
-		usbldo_reg: usbldo {
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-		iosr1_reg: iosr1 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-always-on;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/bcm47094-asus-rt-ac88u.dts b/arch/arm/boot/dts/bcm47094-asus-rt-ac88u.dts
deleted file mode 100644
index 82f9629f0abb..000000000000
--- a/arch/arm/boot/dts/bcm47094-asus-rt-ac88u.dts
+++ /dev/null
@@ -1,275 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-/*
- * Copyright (C) 2021 Arınç ÜNAL <arinc.unal@arinc9.com>
- */
-
-/dts-v1/;
-
-#include "bcm47094.dtsi"
-#include "bcm5301x-nand-cs0-bch8.dtsi"
-
-/ {
-	compatible = "asus,rt-ac88u", "brcm,bcm47094", "brcm,bcm4708";
-	model = "Asus RT-AC88U";
-
-	chosen {
-		bootargs = "earlycon";
-	};
-
-	memory@0 {
-		device_type = "memory";
-		reg = <0x00000000 0x08000000>,
-		      <0x88000000 0x18000000>;
-	};
-
-	nvram@1c080000 {
-		compatible = "brcm,nvram";
-		reg = <0x1c080000 0x00180000>;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		power {
-			label = "white:power";
-			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "default-on";
-		};
-
-		wan-red {
-			label = "red:wan";
-			gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
-		};
-
-		lan {
-			label = "white:lan";
-			gpios = <&chipcommon 21 GPIO_ACTIVE_LOW>;
-		};
-
-		usb2 {
-			label = "white:usb2";
-			gpios = <&chipcommon 16 GPIO_ACTIVE_LOW>;
-			trigger-sources = <&ehci_port2>;
-			linux,default-trigger = "usbport";
-		};
-
-		usb3 {
-			label = "white:usb3";
-			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
-			trigger-sources = <&ehci_port1>, <&xhci_port1>;
-			linux,default-trigger = "usbport";
-		};
-
-		wps {
-			label = "white:wps";
-			gpios = <&chipcommon 19 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		wps {
-			label = "WPS";
-			linux,code = <KEY_WPS_BUTTON>;
-			gpios = <&chipcommon 20 GPIO_ACTIVE_LOW>;
-		};
-
-		reset {
-			label = "Reset";
-			linux,code = <KEY_RESTART>;
-			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
-		};
-
-		wifi {
-			label = "Wi-Fi";
-			linux,code = <KEY_RFKILL>;
-			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
-		};
-
-		led {
-			label = "Backlight";
-			linux,code = <KEY_BRIGHTNESS_ZERO>;
-			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	switch {
-		compatible = "realtek,rtl8365mb";
-		/* 7 = MDIO (has input reads), 6 = MDC (clock, output only) */
-		mdc-gpios = <&chipcommon 6 GPIO_ACTIVE_HIGH>;
-		mdio-gpios = <&chipcommon 7 GPIO_ACTIVE_HIGH>;
-		reset-gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
-		realtek,disable-leds;
-		dsa,member = <1 0>;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				label = "lan5";
-				phy-handle = <&ethphy0>;
-			};
-
-			port@1 {
-				reg = <1>;
-				label = "lan6";
-				phy-handle = <&ethphy1>;
-			};
-
-			port@2 {
-				reg = <2>;
-				label = "lan7";
-				phy-handle = <&ethphy2>;
-			};
-
-			port@3 {
-				reg = <3>;
-				label = "lan8";
-				phy-handle = <&ethphy3>;
-			};
-
-			port@6 {
-				reg = <6>;
-				label = "cpu";
-				ethernet = <&sw0_p5>;
-				phy-mode = "rgmii";
-				tx-internal-delay-ps = <2000>;
-				rx-internal-delay-ps = <2100>;
-
-				fixed-link {
-					speed = <1000>;
-					full-duplex;
-					pause;
-				};
-			};
-		};
-
-		mdio {
-			compatible = "realtek,smi-mdio";
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			ethphy0: ethernet-phy@0 {
-				reg = <0>;
-			};
-
-			ethphy1: ethernet-phy@1 {
-				reg = <1>;
-			};
-
-			ethphy2: ethernet-phy@2 {
-				reg = <2>;
-			};
-
-			ethphy3: ethernet-phy@3 {
-				reg = <3>;
-			};
-		};
-	};
-};
-
-&srab {
-	compatible = "brcm,bcm53012-srab", "brcm,bcm5301x-srab";
-	status = "okay";
-	dsa,member = <0 0>;
-
-	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		port@0 {
-			reg = <0>;
-			label = "lan4";
-		};
-
-		port@1 {
-			reg = <1>;
-			label = "lan3";
-		};
-
-		port@2 {
-			reg = <2>;
-			label = "lan2";
-		};
-
-		port@3 {
-			reg = <3>;
-			label = "lan1";
-		};
-
-		port@4 {
-			reg = <4>;
-			label = "wan";
-		};
-
-		sw0_p5: port@5 {
-			reg = <5>;
-			label = "extsw";
-
-			fixed-link {
-				speed = <1000>;
-				full-duplex;
-				pause;
-			};
-		};
-
-		port@7 {
-			reg = <7>;
-			ethernet = <&gmac1>;
-			label = "cpu";
-
-			fixed-link {
-				speed = <1000>;
-				full-duplex;
-			};
-		};
-
-		port@8 {
-			reg = <8>;
-			ethernet = <&gmac2>;
-			label = "cpu";
-			status = "disabled";
-
-			fixed-link {
-				speed = <1000>;
-				full-duplex;
-			};
-		};
-	};
-};
-
-&usb2 {
-	vcc-gpio = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
-};
-
-&usb3_phy {
-	status = "okay";
-};
-
-&nandcs {
-	partitions {
-		compatible = "fixed-partitions";
-		#address-cells = <1>;
-		#size-cells = <1>;
-
-		partition@0 {
-			label = "boot";
-			reg = <0x00000000 0x00080000>;
-			read-only;
-		};
-
-		partition@80000 {
-			label = "nvram";
-			reg = <0x00080000 0x00180000>;
-		};
-
-		partition@200000 {
-			label = "firmware";
-			reg = <0x00200000 0x07e00000>;
-			compatible = "brcm,trx";
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/bcm59056.dtsi b/arch/arm/boot/dts/bcm59056.dtsi
deleted file mode 100644
index a9bb7ad81378..000000000000
--- a/arch/arm/boot/dts/bcm59056.dtsi
+++ /dev/null
@@ -1,91 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
-* Copyright 2014 Linaro Limited
-* Author: Matt Porter <mporter@linaro.org>
-*/
-
-&pmu {
-	compatible = "brcm,bcm59056";
-	regulators {
-		rfldo_reg: rfldo {
-		};
-
-		camldo1_reg: camldo1 {
-		};
-
-		camldo2_reg: camldo2 {
-		};
-
-		simldo1_reg: simldo1 {
-		};
-
-		simldo2_reg: simldo2 {
-		};
-
-		sdldo_reg: sdldo {
-		};
-
-		sdxldo_reg: sdxldo {
-		};
-
-		mmcldo1_reg: mmcldo1 {
-		};
-
-		mmcldo2_reg: mmcldo2 {
-		};
-
-		audldo_reg: audldo {
-		};
-
-		micldo_reg: micldo {
-		};
-
-		usbldo_reg: usbldo {
-		};
-
-		vibldo_reg: vibldo {
-		};
-
-		csr_reg: csr {
-		};
-
-		iosr1_reg: iosr1 {
-		};
-
-		iosr2_reg: iosr2 {
-		};
-
-		msr_reg: msr {
-		};
-
-		sdsr1_reg: sdsr1 {
-		};
-
-		sdsr2_reg: sdsr2 {
-		};
-
-		vsr_reg: vsr {
-		};
-
-		gpldo1_reg: gpldo1 {
-		};
-
-		gpldo2_reg: gpldo2 {
-		};
-
-		gpldo3_reg: gpldo3 {
-		};
-
-		gpldo4_reg: gpldo4 {
-		};
-
-		gpldo5_reg: gpldo5 {
-		};
-
-		gpldo6_reg: gpldo6 {
-		};
-
-		vbus_reg: vbus {
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/broadcom/Makefile b/arch/arm/boot/dts/broadcom/Makefile
new file mode 100644
index 000000000000..2552e11b5e31
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/Makefile
@@ -0,0 +1,132 @@
+# SPDX-License-Identifier: GPL-2.0
+# Enables support for device-tree overlays
+DTC_FLAGS_bcm2835-rpi-b := -@
+DTC_FLAGS_bcm2835-rpi-a := -@
+DTC_FLAGS_bcm2835-rpi-b-rev2 := -@
+DTC_FLAGS_bcm2835-rpi-b-plus := -@
+DTC_FLAGS_bcm2835-rpi-a-plus := -@
+DTC_FLAGS_bcm2835-rpi-cm1-io1 := -@
+DTC_FLAGS_bcm2836-rpi-2-b := -@
+DTC_FLAGS_bcm2837-rpi-2-b := -@
+DTC_FLAGS_bcm2837-rpi-3-a-plus := -@
+DTC_FLAGS_bcm2837-rpi-3-b := -@
+DTC_FLAGS_bcm2837-rpi-3-b-plus := -@
+DTC_FLAGS_bcm2837-rpi-cm3-io3 := -@
+DTC_FLAGS_bcm2837-rpi-zero-2-w := -@
+DTC_FLAGS_bcm2711-rpi-400 := -@
+DTC_FLAGS_bcm2711-rpi-4-b := -@
+DTC_FLAGS_bcm2711-rpi-cm4-io := -@
+DTC_FLAGS_bcm2835-rpi-zero := -@
+DTC_FLAGS_bcm2835-rpi-zero-w := -@
+dtb-$(CONFIG_ARCH_BCM2835) += \
+	bcm2835-rpi-b.dtb \
+	bcm2835-rpi-a.dtb \
+	bcm2835-rpi-b-rev2.dtb \
+	bcm2835-rpi-b-plus.dtb \
+	bcm2835-rpi-a-plus.dtb \
+	bcm2835-rpi-cm1-io1.dtb \
+	bcm2836-rpi-2-b.dtb \
+	bcm2837-rpi-2-b.dtb \
+	bcm2837-rpi-3-a-plus.dtb \
+	bcm2837-rpi-3-b.dtb \
+	bcm2837-rpi-3-b-plus.dtb \
+	bcm2837-rpi-cm3-io3.dtb \
+	bcm2837-rpi-zero-2-w.dtb \
+	bcm2711-rpi-400.dtb \
+	bcm2711-rpi-4-b.dtb \
+	bcm2711-rpi-cm4-io.dtb \
+	bcm2835-rpi-zero.dtb \
+	bcm2835-rpi-zero-w.dtb
+dtb-$(CONFIG_ARCH_BCMBCA) += \
+	bcm6846-genexis-xg6846b.dtb \
+	bcm947622.dtb \
+	bcm963138.dtb \
+	bcm963138dvt.dtb \
+	bcm963148.dtb \
+	bcm963178.dtb \
+	bcm96756.dtb \
+	bcm96846.dtb \
+	bcm96855.dtb \
+	bcm96878.dtb
+dtb-$(CONFIG_ARCH_BCM_5301X) += \
+	bcm4708-asus-rt-ac56u.dtb \
+	bcm4708-asus-rt-ac68u.dtb \
+	bcm4708-buffalo-wxr-1750dhp.dtb \
+	bcm4708-buffalo-wzr-1750dhp.dtb \
+	bcm4708-buffalo-wzr-1166dhp.dtb \
+	bcm4708-buffalo-wzr-1166dhp2.dtb \
+	bcm4708-linksys-ea6300-v1.dtb \
+	bcm4708-linksys-ea6500-v2.dtb \
+	bcm4708-luxul-xap-1510.dtb \
+	bcm4708-luxul-xwc-1000.dtb \
+	bcm4708-netgear-r6250.dtb \
+	bcm4708-netgear-r6300-v2.dtb \
+	bcm4708-smartrg-sr400ac.dtb \
+	bcm47081-asus-rt-n18u.dtb \
+	bcm47081-buffalo-wzr-600dhp2.dtb \
+	bcm47081-buffalo-wzr-900dhp.dtb \
+	bcm47081-luxul-xap-1410.dtb \
+	bcm47081-luxul-xwr-1200.dtb \
+	bcm47081-tplink-archer-c5-v2.dtb \
+	bcm4709-asus-rt-ac3200.dtb \
+	bcm4709-asus-rt-ac87u.dtb \
+	bcm4709-buffalo-wxr-1900dhp.dtb \
+	bcm4709-linksys-ea9200.dtb \
+	bcm4709-netgear-r7000.dtb \
+	bcm4709-netgear-r8000.dtb \
+	bcm4709-tplink-archer-c9-v1.dtb \
+	bcm47094-asus-rt-ac3100.dtb \
+	bcm47094-asus-rt-ac5300.dtb \
+	bcm47094-asus-rt-ac88u.dtb \
+	bcm47094-dlink-dir-885l.dtb \
+	bcm47094-dlink-dir-890l.dtb \
+	bcm47094-linksys-panamera.dtb \
+	bcm47094-luxul-abr-4500.dtb \
+	bcm47094-luxul-xap-1610.dtb \
+	bcm47094-luxul-xbr-4500.dtb \
+	bcm47094-luxul-xwc-2000.dtb \
+	bcm47094-luxul-xwr-3100.dtb \
+	bcm47094-luxul-xwr-3150-v1.dtb \
+	bcm47094-netgear-r8500.dtb \
+	bcm47094-phicomm-k3.dtb \
+	bcm53015-meraki-mr26.dtb \
+	bcm53016-dlink-dwl-8610ap.dtb \
+	bcm53016-meraki-mr32.dtb \
+	bcm94708.dtb \
+	bcm94709.dtb \
+	bcm953012er.dtb \
+	bcm953012hr.dtb \
+	bcm953012k.dtb
+dtb-$(CONFIG_ARCH_BCM_53573) += \
+	bcm47189-luxul-xap-1440.dtb \
+	bcm47189-luxul-xap-810.dtb \
+	bcm47189-tenda-ac9.dtb \
+	bcm947189acdbmr.dtb
+dtb-$(CONFIG_ARCH_BCM_CYGNUS) += \
+	bcm911360_entphn.dtb \
+	bcm911360k.dtb \
+	bcm958300k.dtb \
+	bcm958305k.dtb
+dtb-$(CONFIG_ARCH_BCM_HR2) += \
+	bcm53340-ubnt-unifi-switch8.dtb
+dtb-$(CONFIG_ARCH_BCM_MOBILE) += \
+	bcm28155-ap.dtb \
+	bcm21664-garnet.dtb \
+	bcm23550-sparrow.dtb
+dtb-$(CONFIG_ARCH_BCM_NSP) += \
+	bcm958522er.dtb \
+	bcm958525er.dtb \
+	bcm958525xmc.dtb \
+	bcm958622hr.dtb \
+	bcm958623hr.dtb \
+	bcm958625-meraki-mx64.dtb \
+	bcm958625-meraki-mx64-a0.dtb \
+	bcm958625-meraki-mx64w.dtb \
+	bcm958625-meraki-mx64w-a0.dtb \
+	bcm958625-meraki-mx65.dtb \
+	bcm958625-meraki-mx65w.dtb \
+	bcm958625hr.dtb \
+	bcm988312hr.dtb \
+	bcm958625k.dtb
+dtb-$(CONFIG_ARCH_BRCMSTB) += \
+	bcm7445-bcm97445svmb.dtb
diff --git a/arch/arm/boot/dts/bcm-cygnus-clock.dtsi b/arch/arm/boot/dts/broadcom/bcm-cygnus-clock.dtsi
index 52f91a12a99a..52f91a12a99a 100644
--- a/arch/arm/boot/dts/bcm-cygnus-clock.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm-cygnus-clock.dtsi
diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/broadcom/bcm-cygnus.dtsi
index ad65be871938..07ca0d993c9f 100644
--- a/arch/arm/boot/dts/bcm-cygnus.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm-cygnus.dtsi
@@ -167,6 +167,7 @@
 			#gpio-cells = <2>;
 			gpio-controller;
 			interrupt-controller;
+			#interrupt-cells = <2>;
 			interrupt-parent = <&mailbox>;
 			interrupts = <0>;
 		};
@@ -247,6 +248,7 @@
 			gpio-controller;
 			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
+			#interrupt-cells = <2>;
 		};
 
 		i2c1: i2c@1800b000 {
@@ -397,8 +399,8 @@
 			#size-cells = <0>;
 			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-0 = <&spi_0>;
-			clocks = <&axi81_clk>;
-			clock-names = "apb_pclk";
+			clocks = <&axi81_clk>, <&axi81_clk>;
+			clock-names = "sspclk", "apb_pclk";
 			status = "disabled";
 		};
 
@@ -409,8 +411,8 @@
 			#size-cells = <0>;
 			interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-0 = <&spi_1>;
-			clocks = <&axi81_clk>;
-			clock-names = "apb_pclk";
+			clocks = <&axi81_clk>, <&axi81_clk>;
+			clock-names = "sspclk", "apb_pclk";
 			status = "disabled";
 		};
 
@@ -421,8 +423,8 @@
 			#size-cells = <0>;
 			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-0 = <&spi_2>;
-			clocks = <&axi81_clk>;
-			clock-names = "apb_pclk";
+			clocks = <&axi81_clk>, <&axi81_clk>;
+			clock-names = "sspclk", "apb_pclk";
 			status = "disabled";
 		};
 
@@ -518,6 +520,7 @@
 			gpio-controller;
 
 			interrupt-controller;
+			#interrupt-cells = <2>;
 			interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-ranges = <&pinctrl 0 42 1>,
 					<&pinctrl 1 44 3>,
diff --git a/arch/arm/boot/dts/bcm-hr2.dtsi b/arch/arm/boot/dts/broadcom/bcm-hr2.dtsi
index 33e6ba63a1ee..75545b10ef2f 100644
--- a/arch/arm/boot/dts/bcm-hr2.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm-hr2.dtsi
@@ -54,8 +54,8 @@
 
 	pmu {
 		compatible = "arm,cortex-a9-pmu";
-		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-affinity = <&cpu0>;
 	};
 
@@ -200,6 +200,7 @@
 			gpio-controller;
 			ngpios = <4>;
 			interrupt-controller;
+			#interrupt-cells = <2>;
 			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/broadcom/bcm-ns.dtsi
index 603c700c706f..d0d5f7e52a91 100644
--- a/arch/arm/boot/dts/bcm5301x.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm-ns.dtsi
@@ -1,11 +1,6 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Broadcom BCM470X / BCM5301X ARM platform code.
- * Generic DTS part for all BCM53010, BCM53011, BCM53012, BCM53014, BCM53015,
- * BCM53016, BCM53017, BCM53018, BCM4707, BCM4708 and BCM4709 SoCs
- *
  * Copyright 2013-2014 Hauke Mehrtens <hauke@hauke-m.de>
- *
- * Licensed under the GNU/GPL. See COPYING for details.
  */
 
 #include <dt-bindings/clock/bcm-nsp.h>
@@ -15,9 +10,16 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 
 / {
+	interrupt-parent = <&gic>;
 	#address-cells = <1>;
 	#size-cells = <1>;
-	interrupt-parent = <&gic>;
+
+	pmu {
+		compatible = "arm,cortex-a9-pmu";
+		interrupts =
+			<GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+	};
 
 	chipcommon-a-bus@18000000 {
 		compatible = "simple-bus";
@@ -50,13 +52,6 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 
-		a9pll: arm_clk@0 {
-			#clock-cells = <0>;
-			compatible = "brcm,nsp-armpll";
-			clocks = <&osc>;
-			reg = <0x00000 0x1000>;
-		};
-
 		scu@20000 {
 			compatible = "arm,cortex-a9-scu";
 			reg = <0x20000 0x100>;
@@ -77,14 +72,6 @@
 			clocks = <&periph_clk>;
 		};
 
-		watchdog@20620 {
-			compatible = "arm,cortex-a9-twd-wdt";
-			reg = <0x20620 0x20>;
-			interrupts = <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) |
-						  IRQ_TYPE_EDGE_RISING)>;
-			clocks = <&periph_clk>;
-		};
-
 		gic: interrupt-controller@21000 {
 			compatible = "arm,cortex-a9-gic";
 			#interrupt-cells = <3>;
@@ -105,49 +92,6 @@
 		};
 	};
 
-	pmu {
-		compatible = "arm,cortex-a9-pmu";
-		interrupts =
-			<GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
-			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
-	};
-
-	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		osc: oscillator {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <25000000>;
-		};
-
-		iprocmed: iprocmed {
-			#clock-cells = <0>;
-			compatible = "fixed-factor-clock";
-			clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
-			clock-div = <2>;
-			clock-mult = <1>;
-		};
-
-		iprocslow: iprocslow {
-			#clock-cells = <0>;
-			compatible = "fixed-factor-clock";
-			clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
-			clock-div = <4>;
-			clock-mult = <1>;
-		};
-
-		periph_clk: periph_clk {
-			#clock-cells = <0>;
-			compatible = "fixed-factor-clock";
-			clocks = <&a9pll>;
-			clock-div = <2>;
-			clock-mult = <1>;
-		};
-	};
-
 	axi@18000000 {
 		compatible = "brcm,bus-axi";
 		reg = <0x18000000 0x1000>;
@@ -157,7 +101,7 @@
 
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0x000fffff 0xffff>;
-		interrupt-map = 
+		interrupt-map =
 			/* ChipCommon */
 			<0x00000000 0 &gic GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
 
@@ -239,14 +183,23 @@
 
 		pcie0: pcie@12000 {
 			reg = <0x00012000 0x1000>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
 		};
 
 		pcie1: pcie@13000 {
 			reg = <0x00013000 0x1000>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
 		};
 
 		pcie2: pcie@14000 {
 			reg = <0x00014000 0x1000>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
 		};
 
 		usb2: usb2@21000 {
@@ -259,8 +212,6 @@
 			interrupt-parent = <&gic>;
 
 			ehci: usb@21000 {
-				#usb-cells = <0>;
-
 				compatible = "generic-ehci";
 				reg = <0x00021000 0x1000>;
 				interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
@@ -281,8 +232,6 @@
 			};
 
 			ohci: usb@22000 {
-				#usb-cells = <0>;
-
 				compatible = "generic-ohci";
 				reg = <0x00022000 0x1000>;
 				interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
@@ -312,8 +261,6 @@
 			interrupt-parent = <&gic>;
 
 			xhci: usb@23000 {
-				#usb-cells = <0>;
-
 				compatible = "generic-xhci";
 				reg = <0x00023000 0x1000>;
 				interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
@@ -332,14 +279,32 @@
 
 		gmac0: ethernet@24000 {
 			reg = <0x24000 0x800>;
+			phy-mode = "internal";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
 		};
 
 		gmac1: ethernet@25000 {
 			reg = <0x25000 0x800>;
+			phy-mode = "internal";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
 		};
 
 		gmac2: ethernet@26000 {
 			reg = <0x26000 0x800>;
+			phy-mode = "internal";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
 		};
 
 		gmac3: ethernet@27000 {
@@ -385,8 +350,61 @@
 		};
 	};
 
-	usb3_dmp: syscon@18105000 {
-		reg = <0x18105000 0x1000>;
+	rng: rng@18004000 {
+		compatible = "brcm,bcm5301x-rng";
+		reg = <0x18004000 0x14>;
+	};
+
+	srab: ethernet-switch@18007000 {
+		compatible = "brcm,bcm53011-srab", "brcm,bcm5301x-srab";
+		reg = <0x18007000 0x1000>;
+
+		status = "disabled";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+			};
+
+			port@1 {
+				reg = <1>;
+			};
+
+			port@2 {
+				reg = <2>;
+			};
+
+			port@3 {
+				reg = <3>;
+			};
+
+			port@4 {
+				reg = <4>;
+			};
+
+			port@5 {
+				reg = <5>;
+				ethernet = <&gmac0>;
+			};
+
+			port@7 {
+				reg = <7>;
+				ethernet = <&gmac1>;
+			};
+
+			port@8 {
+				reg = <8>;
+				ethernet = <&gmac2>;
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+		};
 	};
 
 	uart2: serial@18008000 {
@@ -398,16 +416,6 @@
 		status = "disabled";
 	};
 
-	i2c0: i2c@18009000 {
-		compatible = "brcm,iproc-i2c";
-		reg = <0x18009000 0x50>;
-		interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		clock-frequency = <100000>;
-		status = "disabled";
-	};
-
 	dmu-bus@1800c000 {
 		compatible = "simple-bus";
 		ranges = <0 0x1800c000 0x1000>;
@@ -421,26 +429,6 @@
 			#address-cells = <1>;
 			#size-cells = <1>;
 
-			lcpll0: clock-controller@100 {
-				#clock-cells = <1>;
-				compatible = "brcm,nsp-lcpll0";
-				reg = <0x100 0x14>;
-				clocks = <&osc>;
-				clock-output-names = "lcpll0", "pcie_phy",
-						     "sdio", "ddr_phy";
-			};
-
-			genpll: clock-controller@140 {
-				#clock-cells = <1>;
-				compatible = "brcm,nsp-genpll";
-				reg = <0x140 0x24>;
-				clocks = <&osc>;
-				clock-output-names = "genpll", "phy",
-						     "ethernetclk",
-						     "usbclk", "iprocfast",
-						     "sata1", "sata2";
-			};
-
 			usb2_phy: phy@164 {
 				compatible = "brcm,ns-usb2-phy";
 				reg = <0x164 0x4>;
@@ -455,7 +443,7 @@
 				reg = <0x180 0x4>;
 			};
 
-			pinctrl: pin-controller@1c0 {
+			pinctrl: pinctrl@1c0 {
 				compatible = "brcm,bcm4708-pinmux";
 				reg = <0x1c0 0x24>;
 				reg-names = "cru_gpio_control";
@@ -490,24 +478,6 @@
 		};
 	};
 
-	srab: ethernet-switch@18007000 {
-		compatible = "brcm,bcm53011-srab", "brcm,bcm5301x-srab";
-		reg = <0x18007000 0x1000>;
-
-		status = "disabled";
-
-		/* ports are defined in board DTS */
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-	};
-
-	rng: rng@18004000 {
-		compatible = "brcm,bcm5301x-rng";
-		reg = <0x18004000 0x14>;
-	};
-
 	nand_controller: nand-controller@18028000 {
 		compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1", "brcm,brcmnand";
 		reg = <0x18028000 0x600>, <0x1811a408 0x600>, <0x18028f00 0x20>;
@@ -520,43 +490,8 @@
 		brcm,nand-has-wp;
 	};
 
-	spi@18029200 {
-		compatible = "brcm,spi-nsp-qspi", "brcm,spi-bcm-qspi";
-		reg = <0x18029200 0x184>,
-		      <0x18029000 0x124>,
-		      <0x1811b408 0x004>,
-		      <0x180293a0 0x01c>;
-		reg-names = "mspi", "bspi", "intr_regs", "intr_status_reg";
-		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "mspi_done",
-				  "mspi_halted",
-				  "spi_lr_fullness_reached",
-				  "spi_lr_session_aborted",
-				  "spi_lr_impatient",
-				  "spi_lr_session_done",
-				  "spi_lr_overread";
-		clocks = <&iprocmed>;
-		clock-names = "iprocmed";
-		num-cs = <2>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		spi_nor: flash@0 {
-			compatible = "jedec,spi-nor";
-			reg = <0>;
-			spi-max-frequency = <20000000>;
-			status = "disabled";
-
-			partitions {
-				compatible = "brcm,bcm947xx-cfe-partitions";
-			};
-		};
+	usb3_dmp: syscon@18105000 {
+		reg = <0x18105000 0x1000>;
 	};
 
 	thermal-zones {
@@ -568,9 +503,9 @@
 
 			trips {
 				cpu-crit {
-					temperature	= <125000>;
-					hysteresis	= <0>;
-					type		= "critical";
+					temperature = <125000>;
+					hysteresis = <0>;
+					type = "critical";
 				};
 			};
 
diff --git a/arch/arm/boot/dts/bcm-nsp-ax.dtsi b/arch/arm/boot/dts/broadcom/bcm-nsp-ax.dtsi
index f2e941dbab10..f2e941dbab10 100644
--- a/arch/arm/boot/dts/bcm-nsp-ax.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm-nsp-ax.dtsi
diff --git a/arch/arm/boot/dts/bcm-nsp.dtsi b/arch/arm/boot/dts/broadcom/bcm-nsp.dtsi
index 5b1dc58d40ba..6a4482c93167 100644
--- a/arch/arm/boot/dts/bcm-nsp.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm-nsp.dtsi
@@ -72,8 +72,8 @@
 
 	pmu {
 		compatible = "arm,cortex-a9-pmu";
-		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH
-			      GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-affinity = <&cpu0>, <&cpu1>;
 	};
 
@@ -180,6 +180,7 @@
 			gpio-controller;
 			ngpios = <32>;
 			interrupt-controller;
+			#interrupt-cells = <2>;
 			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-ranges = <&pinctrl 0 0 32>;
 		};
@@ -352,6 +353,7 @@
 			gpio-controller;
 			ngpios = <4>;
 			interrupt-controller;
+			#interrupt-cells = <2>;
 			interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
diff --git a/arch/arm/boot/dts/bcm11351.dtsi b/arch/arm/boot/dts/broadcom/bcm11351.dtsi
index 6197e7d80e3b..53857e572080 100644
--- a/arch/arm/boot/dts/bcm11351.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm11351.dtsi
@@ -1,21 +1,10 @@
-/*
- * Copyright (C) 2012-2013 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2012-2013 Broadcom Corporation
 
+#include <dt-bindings/clock/bcm281xx.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 
-#include "dt-bindings/clock/bcm281xx.h"
-
 / {
 	#address-cells = <1>;
 	#size-cells = <1>;
@@ -60,44 +49,44 @@
 		reg = <0x3404c000 0x400>; /* 1 KiB in SRAM */
 	};
 
-	uart@3e000000 {
+	uartb: serial@3e000000 {
 		compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart";
-		status = "disabled";
 		reg = <0x3e000000 0x1000>;
 		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB>;
 		interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
+		status = "disabled";
 	};
 
-	uart@3e001000 {
+	uartb2: serial@3e001000 {
 		compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart";
-		status = "disabled";
 		reg = <0x3e001000 0x1000>;
 		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB2>;
 		interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
+		status = "disabled";
 	};
 
-	uart@3e002000 {
+	uartb3: serial@3e002000 {
 		compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart";
-		status = "disabled";
 		reg = <0x3e002000 0x1000>;
 		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB3>;
 		interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
+		status = "disabled";
 	};
 
-	uart@3e003000 {
+	uartb4: serial@3e003000 {
 		compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart";
-		status = "disabled";
 		reg = <0x3e003000 0x1000>;
 		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB4>;
 		interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
+		status = "disabled";
 	};
 
 	L2: l2-cache@3ff20000 {
@@ -122,20 +111,19 @@
 	gpio: gpio@35003000 {
 		compatible = "brcm,bcm11351-gpio", "brcm,kona-gpio";
 		reg = <0x35003000 0x800>;
-		interrupts =
-		       <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH
-			GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH
-			GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH
-			GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH
-			GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH
-			GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
 		#gpio-cells = <2>;
 		#interrupt-cells = <2>;
 		gpio-controller;
 		interrupt-controller;
 	};
 
-	sdio1: sdio@3f180000 {
+	sdio1: mmc@3f180000 {
 		compatible = "brcm,kona-sdhci";
 		reg = <0x3f180000 0x10000>;
 		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
@@ -143,7 +131,7 @@
 		status = "disabled";
 	};
 
-	sdio2: sdio@3f190000 {
+	sdio2: mmc@3f190000 {
 		compatible = "brcm,kona-sdhci";
 		reg = <0x3f190000 0x10000>;
 		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
@@ -151,7 +139,7 @@
 		status = "disabled";
 	};
 
-	sdio3: sdio@3f1a0000 {
+	sdio3: mmc@3f1a0000 {
 		compatible = "brcm,kona-sdhci";
 		reg = <0x3f1a0000 0x10000>;
 		interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
@@ -159,7 +147,7 @@
 		status = "disabled";
 	};
 
-	sdio4: sdio@3f1b0000 {
+	sdio4: mmc@3f1b0000 {
 		compatible = "brcm,kona-sdhci";
 		reg = <0x3f1b0000 0x10000>;
 		interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
@@ -172,7 +160,7 @@
 		reg = <0x35004800 0x430>;
 	};
 
-	i2c@3e016000 {
+	bsc1: i2c@3e016000 {
 		compatible = "brcm,bcm11351-i2c", "brcm,kona-i2c";
 		reg = <0x3e016000 0x80>;
 		interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
@@ -182,7 +170,7 @@
 		status = "disabled";
 	};
 
-	i2c@3e017000 {
+	bsc2: i2c@3e017000 {
 		compatible = "brcm,bcm11351-i2c", "brcm,kona-i2c";
 		reg = <0x3e017000 0x80>;
 		interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
@@ -192,7 +180,7 @@
 		status = "disabled";
 	};
 
-	i2c@3e018000 {
+	bsc3: i2c@3e018000 {
 		compatible = "brcm,bcm11351-i2c", "brcm,kona-i2c";
 		reg = <0x3e018000 0x80>;
 		interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
@@ -202,7 +190,7 @@
 		status = "disabled";
 	};
 
-	i2c@3500d000 {
+	pmu_bsc: i2c@3500d000 {
 		compatible = "brcm,bcm11351-i2c", "brcm,kona-i2c";
 		reg = <0x3500d000 0x80>;
 		interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/broadcom/bcm21664-garnet.dts b/arch/arm/boot/dts/broadcom/bcm21664-garnet.dts
new file mode 100644
index 000000000000..4f8ddc1b3ab7
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm21664-garnet.dts
@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2014 Broadcom Corporation
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+#include "bcm21664.dtsi"
+
+/ {
+	model = "BCM21664 Garnet board";
+	compatible = "brcm,bcm21664-garnet", "brcm,bcm21664";
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>; /* 1 GB */
+	};
+};
+
+&sdio1 {
+	max-frequency = <48000000>;
+	status = "okay";
+};
+
+&sdio2 {
+	non-removable;
+	max-frequency = <48000000>;
+	status = "okay";
+};
+
+&sdio4 {
+	max-frequency = <48000000>;
+	cd-gpios = <&gpio 91 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&uartb {
+	status = "okay";
+};
+
+&usbotg {
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm21664.dtsi b/arch/arm/boot/dts/broadcom/bcm21664.dtsi
new file mode 100644
index 000000000000..f0d0300079b6
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm21664.dtsi
@@ -0,0 +1,69 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2014 Broadcom Corporation
+
+#include "bcm2166x-common.dtsi"
+
+/ {
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			enable-method = "brcm,bcm11351-cpu-method";
+			secondary-boot-reg = <0x35004178>;
+			reg = <1>;
+		};
+	};
+};
+
+&apps {
+		gic: interrupt-controller@1c01000 {
+			compatible = "arm,cortex-a9-gic";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0x01c01000 0x1000>,
+				  <0x01c00100 0x100>;
+		};
+
+		L2: cache-controller@1c20000 {
+			compatible = "arm,pl310-cache";
+			reg = <0x01c20000 0x1000>;
+			cache-unified;
+			cache-level = <2>;
+		};
+};
+
+&bsc1 {
+	compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c";
+};
+
+&bsc2 {
+	compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c";
+};
+
+&bsc3 {
+	compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c";
+};
+
+&bsc4 {
+	compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c";
+};
+
+&gpio {
+	compatible = "brcm,bcm21664-gpio", "brcm,kona-gpio";
+};
+
+&smc {
+	compatible = "brcm,bcm21664-smc", "brcm,kona-smc";
+};
diff --git a/arch/arm/boot/dts/bcm23550.dtsi b/arch/arm/boot/dts/broadcom/bcm2166x-common.dtsi
index a36c9b1d23c8..f535212cb52f 100644
--- a/arch/arm/boot/dts/bcm23550.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm2166x-common.dtsi
@@ -1,96 +1,30 @@
+// SPDX-License-Identifier: BSD-3-Clause
 /*
- *  BSD LICENSE
+ * Common device tree for components shared between the BCM21664 and BCM23550
+ * SoCs.
  *
- *  Copyright(c) 2016 Broadcom.  All rights reserved.
- *
- *  Redistribution and use in source and binary forms, with or without
- *  modification, are permitted provided that the following conditions
- *  are met:
- *
- *    * Redistributions of source code must retain the above copyright
- *      notice, this list of conditions and the following disclaimer.
- *    * Redistributions in binary form must reproduce the above copyright
- *      notice, this list of conditions and the following disclaimer in
- *      the documentation and/or other materials provided with the
- *      distribution.
- *    * Neither the name of Broadcom Corporation nor the names of its
- *      contributors may be used to endorse or promote products derived
- *      from this software without specific prior written permission.
- *
- *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
- *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
- *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
- *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
- *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
- *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ * Copyright (C) 2016 Broadcom
  */
 
+/dts-v1/;
+
+#include <dt-bindings/clock/bcm21664.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 
-/* BCM23550 and BCM21664 have almost identical clocks */
-#include "dt-bindings/clock/bcm21664.h"
-
 / {
 	#address-cells = <1>;
 	#size-cells = <1>;
-	model = "BCM23550 SoC";
-	compatible = "brcm,bcm23550";
-	interrupt-parent = <&gic>;
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu0: cpu@0 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a7";
-			reg = <0>;
-			clock-frequency = <1000000000>;
-		};
-
-		cpu1: cpu@1 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a7";
-			enable-method = "brcm,bcm23550";
-			secondary-boot-reg = <0x35004178>;
-			reg = <1>;
-			clock-frequency = <1000000000>;
-		};
-
-		cpu2: cpu@2 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a7";
-			enable-method = "brcm,bcm23550";
-			secondary-boot-reg = <0x35004178>;
-			reg = <2>;
-			clock-frequency = <1000000000>;
-		};
-
-		cpu3: cpu@3 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a7";
-			enable-method = "brcm,bcm23550";
-			secondary-boot-reg = <0x35004178>;
-			reg = <3>;
-			clock-frequency = <1000000000>;
-		};
-	};
 
 	/* Hub bus */
-	hub@34000000 {
+	hub: hub-bus@34000000 {
 		compatible = "simple-bus";
 		ranges = <0 0x34000000 0x102f83ac>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 
-		smc@4e000 {
-			compatible = "brcm,bcm23550-smc", "brcm,kona-smc";
+		smc: smc@4e000 {
+			/* Compatible filled by SoC DTSI */
 			reg = <0x0004e000 0x400>; /* 1 KiB in SRAM */
 		};
 
@@ -100,19 +34,23 @@
 		};
 
 		gpio: gpio@1003000 {
-			compatible = "brcm,bcm23550-gpio", "brcm,kona-gpio";
+			/* Compatible filled by SoC DTSI */
 			reg = <0x01003000 0x524>;
-			interrupts =
-			       <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH
-				GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH
-				GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH
-				GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
 			#gpio-cells = <2>;
 			#interrupt-cells = <2>;
 			gpio-controller;
 			interrupt-controller;
 		};
 
+		pinctrl: pinctrl@1004800 {
+			compatible = "brcm,bcm21664-pinctrl";
+			reg = <0x01004800 0x7f4>;
+		};
+
 		timer@1006000 {
 			compatible = "brcm,kona-timer";
 			reg = <0x01006000 0x1c>;
@@ -122,7 +60,7 @@
 	};
 
 	/* Slaves bus */
-	slaves@3e000000 {
+	slaves: slaves-bus@3e000000 {
 		compatible = "simple-bus";
 		ranges = <0 0x3e000000 0x0001c070>;
 		#address-cells = <1>;
@@ -130,36 +68,36 @@
 
 		uartb: serial@0 {
 			compatible = "snps,dw-apb-uart";
-			status = "disabled";
 			reg = <0x00000000 0x118>;
 			clocks = <&slave_ccu BCM21664_SLAVE_CCU_UARTB>;
 			interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
+			status = "disabled";
 		};
 
 		uartb2: serial@1000 {
 			compatible = "snps,dw-apb-uart";
-			status = "disabled";
 			reg = <0x00001000 0x118>;
 			clocks = <&slave_ccu BCM21664_SLAVE_CCU_UARTB2>;
 			interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
+			status = "disabled";
 		};
 
 		uartb3: serial@2000 {
 			compatible = "snps,dw-apb-uart";
-			status = "disabled";
 			reg = <0x00002000 0x118>;
 			clocks = <&slave_ccu BCM21664_SLAVE_CCU_UARTB3>;
 			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
+			status = "disabled";
 		};
 
 		bsc1: i2c@16000 {
-			compatible = "brcm,kona-i2c";
+			/* Compatible filled by SoC DTSI */
 			reg = <0x00016000 0x70>;
 			interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
@@ -169,7 +107,7 @@
 		};
 
 		bsc2: i2c@17000 {
-			compatible = "brcm,kona-i2c";
+			/* Compatible filled by SoC DTSI */
 			reg = <0x00017000 0x70>;
 			interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
@@ -179,7 +117,7 @@
 		};
 
 		bsc3: i2c@18000 {
-			compatible = "brcm,kona-i2c";
+			/* Compatible filled by SoC DTSI */
 			reg = <0x00018000 0x70>;
 			interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
@@ -189,7 +127,7 @@
 		};
 
 		bsc4: i2c@1c000 {
-			compatible = "brcm,kona-i2c";
+			/* Compatible filled by SoC DTSI */
 			reg = <0x0001c000 0x70>;
 			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
@@ -200,9 +138,9 @@
 	};
 
 	/* Apps bus */
-	apps@3e300000 {
+	apps: apps-bus@3e300000 {
 		compatible = "simple-bus";
-		ranges = <0 0x3e300000 0x01b77000>;
+		ranges = <0 0x3e300000 0x01c02000>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 
@@ -224,7 +162,7 @@
 			status = "disabled";
 		};
 
-		sdio1: sdio@e80000 {
+		sdio1: mmc@e80000 {
 			compatible = "brcm,kona-sdhci";
 			reg = <0x00e80000 0x801c>;
 			interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
@@ -232,7 +170,7 @@
 			status = "disabled";
 		};
 
-		sdio2: sdio@e90000 {
+		sdio2: mmc@e90000 {
 			compatible = "brcm,kona-sdhci";
 			reg = <0x00e90000 0x801c>;
 			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
@@ -240,7 +178,7 @@
 			status = "disabled";
 		};
 
-		sdio3: sdio@ea0000 {
+		sdio3: mmc@ea0000 {
 			compatible = "brcm,kona-sdhci";
 			reg = <0x00ea0000 0x801c>;
 			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
@@ -248,27 +186,13 @@
 			status = "disabled";
 		};
 
-		sdio4: sdio@eb0000 {
+		sdio4: mmc@eb0000 {
 			compatible = "brcm,kona-sdhci";
 			reg = <0x00eb0000 0x801c>;
 			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&master_ccu BCM21664_MASTER_CCU_SDIO4>;
 			status = "disabled";
 		};
-
-		cdc: cdc@1b0e000 {
-			compatible = "brcm,bcm23550-cdc";
-			reg = <0x01b0e000 0x78>;
-		};
-
-		gic: interrupt-controller@1b21000 {
-			compatible = "arm,cortex-a9-gic";
-			#interrupt-cells = <3>;
-			#address-cells = <0>;
-			interrupt-controller;
-			reg = <0x01b21000 0x1000>,
-			      <0x01b22000 0x1000>;
-		};
 	};
 
 	clocks {
@@ -372,21 +296,21 @@
 		};
 
 		root_ccu: root_ccu@35001000 {
-			compatible = BCM21664_DT_ROOT_CCU_COMPAT;
+			compatible = "brcm,bcm21664-root-ccu";
 			reg = <0x35001000 0x0f00>;
 			#clock-cells = <1>;
 			clock-output-names = "frac_1m";
 		};
 
 		aon_ccu: aon_ccu@35002000 {
-			compatible = BCM21664_DT_AON_CCU_COMPAT;
+			compatible = "brcm,bcm21664-aon-ccu";
 			reg = <0x35002000 0x0f00>;
 			#clock-cells = <1>;
 			clock-output-names = "hub_timer";
 		};
 
 		slave_ccu: slave_ccu@3e011000 {
-			compatible = BCM21664_DT_SLAVE_CCU_COMPAT;
+			compatible = "brcm,bcm21664-slave-ccu";
 			reg = <0x3e011000 0x0f00>;
 			#clock-cells = <1>;
 			clock-output-names = "uartb",
@@ -399,7 +323,7 @@
 		};
 
 		master_ccu: master_ccu@3f001000 {
-			compatible = BCM21664_DT_MASTER_CCU_COMPAT;
+			compatible = "brcm,bcm21664-master-ccu";
 			reg = <0x3f001000 0x0f00>;
 			#clock-cells = <1>;
 			clock-output-names = "sdio1",
@@ -413,3 +337,5 @@
 		};
 	};
 };
+
+#include "bcm2166x-pinctrl.dtsi"
diff --git a/arch/arm/boot/dts/broadcom/bcm2166x-pinctrl.dtsi b/arch/arm/boot/dts/broadcom/bcm2166x-pinctrl.dtsi
new file mode 100644
index 000000000000..51b8730c8fee
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm2166x-pinctrl.dtsi
@@ -0,0 +1,297 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Common pinmux configrations for BCM2166x (BCM21664/BCM23550).
+ *
+ * Copyright (C) 2025 Artur Weber <aweber.kernel@gmail.com>
+ */
+
+&pinctrl {
+	/* BSC1 */
+	bsc1_pins: bsc1-pins {
+		bsc1clk-grp0 {
+			pins = "bsc1clk";
+			function = "alt1"; /* BSC1CLK */
+		};
+
+		bsc1dat-grp0 {
+			pins = "bsc1dat";
+			function = "alt1"; /* BSC1DAT */
+		};
+	};
+
+	/* BSC2 */
+	bsc2_pins: bsc2-pins {
+		bsc2clk-grp0 {
+			pins = "gpio16";
+			function = "alt2"; /* BSC2CLK */
+		};
+
+		bsc2dat-grp0 {
+			pins = "gpio17";
+			function = "alt2"; /* BSC2DAT */
+		};
+	};
+
+	/* BSC3 */
+	bsc3_pins: bsc3-pins {
+		bsc3clk-grp0 {
+			pins = "lcdscl";
+			function = "alt1"; /* BSC3_CLK */
+		};
+
+		bsc3dat-grp0 {
+			pins = "lcdsda";
+			function = "alt1"; /* BSC3_SDA */
+		};
+	};
+
+	/* BSC4 */
+	bsc4_pins: bsc4-pins {
+		bsc4clk-grp0 {
+			pins = "lcdres";
+			function = "alt1"; /* BSC4_CLK */
+		};
+
+		bsc4dat-grp0 {
+			pins = "lcdte";
+			function = "alt1"; /* BSC4_SDA */
+		};
+	};
+
+	/* PMBSC */
+	pmbsc_pins: pmbsc-pins {
+		pmbscclk-grp0 {
+			pins = "pmbscclk";
+			function = "alt1"; /* PMBSCCLK */
+		};
+
+		pmbscdat-grp0 {
+			pins = "pmbscdat";
+			function = "alt1"; /* PMBSCDAT */
+		};
+	};
+
+	/* SD */
+	sd_width1_pins: sd-width1-pins {
+		sdck-grp0 {
+			pins = "sdck";
+			function = "alt1"; /* SDCK */
+			bias-disable;
+		};
+
+		sdcmd-grp0 {
+			pins = "sdcmd";
+			function = "alt1"; /* SDCMD */
+			bias-pull-up;
+		};
+
+		sddat-grp0 {
+			pins = "sddat0";
+			function = "alt1"; /* SDDATx */
+			bias-pull-up;
+		};
+	};
+
+	sd_width4_pins: sd-width4-pins {
+		sdck-grp0 {
+			pins = "sdck";
+			function = "alt1"; /* SDCK */
+			bias-disable;
+		};
+
+		sdcmd-grp0 {
+			pins = "sdcmd";
+			function = "alt1"; /* SDCMD */
+			bias-pull-up;
+		};
+
+		sddat-grp0 {
+			pins = "sddat0", "sddat1", "sddat2", "sddat3";
+			function = "alt1"; /* SDDATx */
+			bias-pull-up;
+		};
+	};
+
+	/* SD1 */
+	sd1_width1_pins: sd1-width1-pins {
+		sd1ck-grp0 {
+			pins = "mmc1dat7";
+			function = "alt6"; /* SD1CK */
+			bias-disable;
+		};
+
+		sd1cmd-grp0 {
+			pins = "spi0txd";
+			function = "alt2"; /* SD1CMD */
+			bias-pull-up;
+		};
+
+		sd1dat0-grp0 {
+			pins = "mmc1dat5";
+			function = "alt6"; /* SD1DAT0 */
+			bias-pull-up;
+		};
+	};
+
+	sd1_width4_pins: sd1-width4-pins {
+		sd1ck-grp0 {
+			pins = "mmc1dat7";
+			function = "alt6"; /* SD1CK */
+			bias-disable;
+		};
+
+		sd1cmd-grp0 {
+			pins = "spi0txd";
+			function = "alt2"; /* SD1CMD */
+			bias-pull-up;
+		};
+
+		sd1dat0-grp0 {
+			pins = "mmc1dat5";
+			function = "alt6"; /* SD1DAT0 */
+			bias-pull-up;
+		};
+
+		sd1dat1-grp0 {
+			pins = "gpio93";
+			function = "alt1"; /* SD1DAT1 */
+			bias-pull-up;
+		};
+
+		sd1dat2-grp0 {
+			pins = "gpio94";
+			function = "alt1"; /* SD1DAT2 */
+			bias-pull-up;
+		};
+
+		sd1dat3-grp0 {
+			pins = "mmc1dat3";
+			function = "alt6"; /* SD1DAT3 */
+			bias-pull-up;
+		};
+	};
+
+	/* MMC0 */
+	mmc0_width1_pins: mmc0-width1-pins {
+		mmc0ck-grp0 {
+			pins = "mmc0ck";
+			function = "alt1"; /* MMC0CK */
+			bias-disable;
+		};
+
+		mmc0cmd-grp0 {
+			pins = "mmc0cmd";
+			function = "alt1"; /* MMC0CMD */
+			bias-pull-up;
+		};
+
+		mmc0dat-grp0 {
+			pins = "mmc0dat0";
+			function = "alt1"; /* MMC0DATx */
+			bias-pull-up;
+		};
+	};
+
+	mmc0_width4_pins: mmc0-width4-pins {
+		mmc0ck-grp0 {
+			pins = "mmc0ck";
+			function = "alt1"; /* MMC0CK */
+			bias-disable;
+		};
+
+		mmc0cmd-grp0 {
+			pins = "mmc0cmd";
+			function = "alt1"; /* MMC0CMD */
+			bias-pull-up;
+		};
+
+		mmc0dat-grp0 {
+			pins = "mmc0dat0", "mmc0dat1", "mmc0dat2", "mmc0dat3";
+			function = "alt1"; /* MMC0DATx */
+			bias-pull-up;
+		};
+	};
+
+	mmc0_width8_pins: mmc0-width8-pins {
+		mmc0ck-grp0 {
+			pins = "mmc0ck";
+			function = "alt1"; /* MMC0CK */
+			bias-disable;
+		};
+
+		mmc0cmd-grp0 {
+			pins = "mmc0cmd";
+			function = "alt1"; /* MMC0CMD */
+			bias-pull-up;
+		};
+
+		mmc0dat-grp0 {
+			pins = "mmc0dat0", "mmc0dat1", "mmc0dat2", "mmc0dat3",
+			       "mmc0dat4", "mmc0dat5", "mmc0dat6", "mmc0dat7";
+			function = "alt1"; /* MMC0DATx */
+			bias-pull-up;
+		};
+	};
+
+	/* MMC1 */
+	mmc1_width1_pins: mmc1-width1-pins {
+		mmc1ck-grp0 {
+			pins = "mmc1ck";
+			function = "alt1"; /* MMC1CK */
+			bias-disable;
+		};
+
+		mmc1cmd-grp0 {
+			pins = "mmc1cmd";
+			function = "alt1"; /* MMC1CMD */
+			bias-pull-up;
+		};
+
+		mmc1dat-grp0 {
+			pins = "mmc1dat0";
+			function = "alt1"; /* MMC1DATx */
+			bias-pull-up;
+		};
+	};
+
+	mmc1_width4_pins: mmc1-width4-pins {
+		mmc1ck-grp0 {
+			pins = "mmc1ck";
+			function = "alt1"; /* MMC1CK */
+			bias-disable;
+		};
+
+		mmc1cmd-grp0 {
+			pins = "mmc1cmd";
+			function = "alt1"; /* MMC1CMD */
+			bias-pull-up;
+		};
+
+		mmc1dat-grp0 {
+			pins = "mmc1dat0", "mmc1dat1", "mmc1dat2", "mmc1dat3";
+			function = "alt1"; /* MMC1DATx */
+			bias-pull-up;
+		};
+	};
+
+	mmc1_width8_pins: mmc1-width8-pins {
+		mmc1ck-grp0 {
+			pins = "mmc1ck";
+			function = "alt1"; /* MMC1CK */
+			bias-disable;
+		};
+
+		mmc1cmd-grp0 {
+			pins = "mmc1cmd";
+			function = "alt1"; /* MMC1CMD */
+			bias-pull-up;
+		};
+
+		mmc1dat-grp0 {
+			pins = "mmc1dat0", "mmc1dat1", "mmc1dat2", "mmc1dat3",
+			       "mmc1dat4", "mmc1dat5", "mmc1dat6", "mmc1dat7";
+			function = "alt1"; /* MMC1DATx */
+			bias-pull-up;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm23550-sparrow.dts b/arch/arm/boot/dts/broadcom/bcm23550-sparrow.dts
index ace77709f468..ace77709f468 100644
--- a/arch/arm/boot/dts/bcm23550-sparrow.dts
+++ b/arch/arm/boot/dts/broadcom/bcm23550-sparrow.dts
diff --git a/arch/arm/boot/dts/broadcom/bcm23550.dtsi b/arch/arm/boot/dts/broadcom/bcm23550.dtsi
new file mode 100644
index 000000000000..c1c69381286b
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm23550.dtsi
@@ -0,0 +1,91 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Device tree for the BCM23550 SoC.
+ *
+ * Copyright (C) 2016 Broadcom
+ */
+
+#include "bcm2166x-common.dtsi"
+
+/ {
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0>;
+			clock-frequency = <1000000000>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			enable-method = "brcm,bcm23550";
+			secondary-boot-reg = <0x35004178>;
+			reg = <1>;
+			clock-frequency = <1000000000>;
+		};
+
+		cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			enable-method = "brcm,bcm23550";
+			secondary-boot-reg = <0x35004178>;
+			reg = <2>;
+			clock-frequency = <1000000000>;
+		};
+
+		cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			enable-method = "brcm,bcm23550";
+			secondary-boot-reg = <0x35004178>;
+			reg = <3>;
+			clock-frequency = <1000000000>;
+		};
+	};
+};
+
+&apps {
+		cdc: cdc@1b0e000 {
+			compatible = "brcm,bcm23550-cdc";
+			reg = <0x01b0e000 0x78>;
+		};
+
+		gic: interrupt-controller@1b21000 {
+			compatible = "arm,cortex-a9-gic";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0x01b21000 0x1000>,
+			      <0x01b22000 0x1000>;
+		};
+};
+
+&bsc1 {
+	compatible = "brcm,bcm23550-i2c", "brcm,kona-i2c";
+};
+
+&bsc2 {
+	compatible = "brcm,bcm23550-i2c", "brcm,kona-i2c";
+};
+
+&bsc3 {
+	compatible = "brcm,bcm23550-i2c", "brcm,kona-i2c";
+};
+
+&bsc4 {
+	compatible = "brcm,bcm23550-i2c", "brcm,kona-i2c";
+};
+
+&gpio {
+	compatible = "brcm,bcm23550-gpio", "brcm,kona-gpio";
+};
+
+&smc {
+	compatible = "brcm,bcm23550-smc", "brcm,kona-smc";
+};
diff --git a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts b/arch/arm/boot/dts/broadcom/bcm2711-rpi-4-b.dts
index 4432412044de..353bb50ce542 100644
--- a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2711-rpi-4-b.dts
@@ -2,8 +2,10 @@
 /dts-v1/;
 #include "bcm2711.dtsi"
 #include "bcm2711-rpi.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
 #include "bcm283x-rpi-usb-peripheral.dtsi"
 #include "bcm283x-rpi-wifi-bt.dtsi"
+#include <dt-bindings/leds/common.h>
 
 / {
 	compatible = "raspberrypi,4-model-b", "brcm,bcm2711";
@@ -14,20 +16,14 @@
 		stdout-path = "serial1:115200n8";
 	};
 
-	leds {
-		led-act {
-			gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
-		};
-
-		led-pwr {
-			label = "PWR";
-			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
-			default-state = "keep";
-			linux,default-trigger = "default-on";
-		};
+	cam1_reg: regulator-cam1 {
+		compatible = "regulator-fixed";
+		regulator-name = "cam1-reg";
+		enable-active-high;
+		gpio = <&expgpio 5 GPIO_ACTIVE_HIGH>;
 	};
 
-	sd_io_1v8_reg: sd_io_1v8_reg {
+	sd_io_1v8_reg: regulator-sd-io-1v8 {
 		compatible = "regulator-gpio";
 		regulator-name = "vdd-sd-io";
 		regulator-min-microvolt = <1800000>;
@@ -41,7 +37,7 @@
 		status = "okay";
 	};
 
-	sd_vcc_reg: sd_vcc_reg {
+	sd_vcc_reg: regulator-sd-vcc {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc-sd";
 		regulator-min-microvolt = <3300000>;
@@ -156,6 +152,19 @@
 	status = "okay";
 };
 
+&led_act {
+	gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
+};
+
+&leds {
+	led_pwr: led-pwr {
+		label = "PWR";
+		gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+		default-state = "keep";
+		linux,default-trigger = "default-on";
+	};
+};
+
 &pixelvalve0 {
 	status = "okay";
 };
@@ -196,6 +205,27 @@
 	phy1: ethernet-phy@1 {
 		/* No PHY interrupt */
 		reg = <0x1>;
+
+		leds {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* LED1 */
+			led@0 {
+				reg = <0>;
+				color = <LED_COLOR_ID_GREEN>;
+				function = LED_FUNCTION_LAN;
+				default-state = "keep";
+			};
+
+			/* LED2 */
+			led@1 {
+				reg = <1>;
+				color = <LED_COLOR_ID_AMBER>;
+				function = LED_FUNCTION_LAN;
+				default-state = "keep";
+			};
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/bcm2711-rpi-400.dts b/arch/arm/boot/dts/broadcom/bcm2711-rpi-400.dts
index f4d2fc20397c..ca9be91b4f36 100644
--- a/arch/arm/boot/dts/bcm2711-rpi-400.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2711-rpi-400.dts
@@ -11,14 +11,6 @@
 		stdout-path = "serial1:115200n8";
 	};
 
-	leds {
-		/delete-node/ led-act;
-
-		led-pwr {
-			gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
-		};
-	};
-
 	gpio-poweroff {
 		compatible = "gpio-poweroff";
 		gpios = <&expgpio 5 GPIO_ACTIVE_HIGH>;
@@ -28,18 +20,25 @@
 &expgpio {
 	gpio-line-names = "BT_ON",
 			  "WL_ON",
-			  "",
+			  "PWR_LED_OFF",
 			  "GLOBAL_RESET",
 			  "VDD_SD_IO_SEL",
-			  "CAM_GPIO",
+			  "GLOBAL_SHUTDOWN",
 			  "SD_PWR_ON",
-			  "SD_OC_N";
+			  "SHUTDOWN_REQUEST";
 };
 
 &genet_mdio {
 	clock-frequency = <1950000>;
+	/delete-node/ leds;
 };
 
+&led_pwr {
+	gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
+};
+
+/delete-node/ &led_act;
+
 &pm {
 	/delete-property/ system-power-controller;
 };
diff --git a/arch/arm/boot/dts/bcm2711-rpi-cm4-io.dts b/arch/arm/boot/dts/broadcom/bcm2711-rpi-cm4-io.dts
index 19600b629be5..6bc77dd48c0d 100644
--- a/arch/arm/boot/dts/bcm2711-rpi-cm4-io.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2711-rpi-cm4-io.dts
@@ -1,23 +1,12 @@
 // SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
+#include <dt-bindings/leds/common.h>
 #include "bcm2711-rpi-cm4.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
 
 / {
 	model = "Raspberry Pi Compute Module 4 IO Board";
-
-	leds {
-		led-act {
-			gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
-		};
-
-		led-pwr {
-			label = "PWR";
-			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
-			default-state = "keep";
-			linux,default-trigger = "default-on";
-		};
-	};
 };
 
 &ddc0 {
@@ -113,6 +102,51 @@
 	status = "okay";
 };
 
+&i2c0_1 {
+	rtc@51 {
+		/* Attention: An alarm resets the machine */
+		compatible = "nxp,pcf85063a";
+		reg = <0x51>;
+		quartz-load-femtofarads = <7000>;
+	};
+};
+
+&phy1 {
+	leds {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* LED2 */
+		led@1 {
+			reg = <1>;
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_LAN;
+			default-state = "keep";
+		};
+
+		/* LED3 */
+		led@2 {
+			reg = <2>;
+			color = <LED_COLOR_ID_AMBER>;
+			function = LED_FUNCTION_LAN;
+			default-state = "keep";
+		};
+	};
+};
+
+&led_act {
+	gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
+};
+
+&leds {
+	led-pwr {
+		label = "PWR";
+		gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+		default-state = "keep";
+		linux,default-trigger = "default-on";
+	};
+};
+
 &pixelvalve0 {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/bcm2711-rpi-cm4.dtsi b/arch/arm/boot/dts/broadcom/bcm2711-rpi-cm4.dtsi
index a2954d466a73..48e63ab7848c 100644
--- a/arch/arm/boot/dts/bcm2711-rpi-cm4.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm2711-rpi-cm4.dtsi
@@ -12,7 +12,7 @@
 		stdout-path = "serial1:115200n8";
 	};
 
-	sd_io_1v8_reg: sd_io_1v8_reg {
+	sd_io_1v8_reg: regulator-sd-io-1v8 {
 		compatible = "regulator-gpio";
 		regulator-name = "vdd-sd-io";
 		regulator-min-microvolt = <1800000>;
@@ -26,7 +26,7 @@
 		status = "okay";
 	};
 
-	sd_vcc_reg: sd_vcc_reg {
+	sd_vcc_reg: regulator-sd-vcc {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc-sd";
 		regulator-min-microvolt = <3300000>;
diff --git a/arch/arm/boot/dts/bcm2711-rpi.dtsi b/arch/arm/boot/dts/broadcom/bcm2711-rpi.dtsi
index ca266c5d9f9b..c78ed064d166 100644
--- a/arch/arm/boot/dts/bcm2711-rpi.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm2711-rpi.dtsi
@@ -16,14 +16,33 @@
 		pcie0 = &pcie0;
 		blconfig = &blconfig;
 	};
-};
 
-&firmware {
-	firmware_clocks: clocks {
-		compatible = "raspberrypi,firmware-clocks";
-		#clock-cells = <1>;
+	i2c0mux: i2c-mux0 {
+		compatible = "i2c-mux-pinctrl";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c-parent = <&i2c0>;
+
+		pinctrl-names = "i2c0", "i2c0-vc";
+		pinctrl-0 = <&i2c0_gpio0>;
+		pinctrl-1 = <&i2c0_gpio44>;
+
+		i2c0_0: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c0_1: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
 	};
+};
 
+&firmware {
 	expgpio: gpio {
 		compatible = "raspberrypi,firmware-gpio";
 		gpio-controller;
@@ -53,6 +72,11 @@
 	clocks = <&firmware_clocks 4>;
 };
 
+&i2c0 {
+	/delete-property/ pinctrl-names;
+	/delete-property/ pinctrl-0;
+};
+
 &rmem {
 	/*
 	 * RPi4's co-processor will copy the board's bootloader configuration
@@ -69,6 +93,10 @@
 	};
 };
 
+&v3d {
+	clocks = <&firmware_clocks 5>;
+};
+
 &vchiq {
 	interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
 };
diff --git a/arch/arm/boot/dts/bcm2711.dtsi b/arch/arm/boot/dts/broadcom/bcm2711.dtsi
index 89af57482bc8..c06d9f5e53c8 100644
--- a/arch/arm/boot/dts/bcm2711.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm2711.dtsi
@@ -48,7 +48,7 @@
 		 * This node is the provider for the enable-method for
 		 * bringing up secondary cores.
 		 */
-		local_intc: local_intc@40000000 {
+		local_intc: interrupt-controller@40000000 {
 			compatible = "brcm,bcm2836-l1-intc";
 			reg = <0x40000000 0x100>;
 		};
@@ -76,7 +76,7 @@
 			};
 		};
 
-		dma: dma@7e007000 {
+		dma: dma-controller@7e007000 {
 			compatible = "brcm,bcm2835-dma";
 			reg = <0x7e007000 0xb00>;
 			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>,
@@ -107,12 +107,13 @@
 		};
 
 		pm: watchdog@7e100000 {
-			compatible = "brcm,bcm2835-pm", "brcm,bcm2835-pm-wdt";
+			compatible = "brcm,bcm2711-pm", "brcm,bcm2835-pm-wdt";
 			#power-domain-cells = <1>;
 			#reset-cells = <1>;
 			reg = <0x7e100000 0x114>,
 			      <0x7e00a000 0x24>,
 			      <0x7ec11000 0x20>;
+			reg-names = "pm", "asb", "rpivid_asb";
 			clocks = <&clocks BCM2835_CLOCK_V3D>,
 				 <&clocks BCM2835_CLOCK_PERI_IMAGE>,
 				 <&clocks BCM2835_CLOCK_H264>,
@@ -133,7 +134,7 @@
 			clocks = <&clocks BCM2835_CLOCK_UART>,
 				 <&clocks BCM2835_CLOCK_VPU>;
 			clock-names = "uartclk", "apb_pclk";
-			arm,primecell-periphid = <0x00241011>;
+			arm,primecell-periphid = <0x00341011>;
 			status = "disabled";
 		};
 
@@ -144,7 +145,7 @@
 			clocks = <&clocks BCM2835_CLOCK_UART>,
 				 <&clocks BCM2835_CLOCK_VPU>;
 			clock-names = "uartclk", "apb_pclk";
-			arm,primecell-periphid = <0x00241011>;
+			arm,primecell-periphid = <0x00341011>;
 			status = "disabled";
 		};
 
@@ -155,7 +156,7 @@
 			clocks = <&clocks BCM2835_CLOCK_UART>,
 				 <&clocks BCM2835_CLOCK_VPU>;
 			clock-names = "uartclk", "apb_pclk";
-			arm,primecell-periphid = <0x00241011>;
+			arm,primecell-periphid = <0x00341011>;
 			status = "disabled";
 		};
 
@@ -166,7 +167,7 @@
 			clocks = <&clocks BCM2835_CLOCK_UART>,
 				 <&clocks BCM2835_CLOCK_VPU>;
 			clock-names = "uartclk", "apb_pclk";
-			arm,primecell-periphid = <0x00241011>;
+			arm,primecell-periphid = <0x00341011>;
 			status = "disabled";
 		};
 
@@ -277,7 +278,7 @@
 			clocks = <&clocks BCM2835_CLOCK_PWM>;
 			assigned-clocks = <&clocks BCM2835_CLOCK_PWM>;
 			assigned-clock-rates = <10000000>;
-			#pwm-cells = <2>;
+			#pwm-cells = <3>;
 			status = "disabled";
 		};
 
@@ -431,8 +432,8 @@
 		};
 	};
 
-	arm-pmu {
-		compatible = "arm,cortex-a72-pmu", "arm,armv8-pmuv3";
+	pmu {
+		compatible = "arm,cortex-a72-pmu";
 		interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
 			<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
 			<GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
@@ -450,8 +451,6 @@
 					  IRQ_TYPE_LEVEL_LOW)>,
 			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) |
 					  IRQ_TYPE_LEVEL_LOW)>;
-		/* This only applies to the ARMv7 stub */
-		arm,cpu-registers-not-fw-configured;
 	};
 
 	cpus: cpus {
@@ -535,6 +534,7 @@
 		 */
 		l2: l2-cache0 {
 			compatible = "cache";
+			cache-unified;
 			cache-size = <0x100000>;
 			cache-line-size = <64>;
 			cache-sets = <1024>; // 1MiB(size)/64(line-size)=16384ways/16-way set
@@ -601,6 +601,32 @@
 				#size-cells = <0x0>;
 			};
 		};
+
+		xhci: usb@7e9c0000 {
+			compatible = "brcm,bcm2711-xhci", "brcm,xhci-brcm-v2";
+			reg = <0x0 0x7e9c0000 0x100000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
+			power-domains = <&pm BCM2835_POWER_DOMAIN_USB>;
+			/* DWC2 and this IP block share the same USB PHY,
+			 * enabling both at the same time results in lockups.
+			 * So keep this node disabled and let the bootloader
+			 * decide which interface should be enabled.
+			 */
+			status = "disabled";
+		};
+
+		v3d: gpu@7ec00000 {
+			compatible = "brcm,2711-v3d";
+			reg = <0x0 0x7ec00000 0x4000>,
+			      <0x0 0x7ec04000 0x4000>;
+			reg-names = "hub", "core0";
+
+			power-domains = <&pm BCM2835_POWER_DOMAIN_GRAFX_V3D>;
+			resets = <&pm BCM2835_RESET_V3D>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+		};
 	};
 };
 
@@ -635,21 +661,21 @@
 
 	gpio-ranges = <&gpio 0 0 58>;
 
-	gpclk0_gpio49: gpclk0_gpio49 {
+	gpclk0_gpio49: gpclk0-gpio49 {
 		pin-gpclk {
 			pins = "gpio49";
 			function = "alt1";
 			bias-disable;
 		};
 	};
-	gpclk1_gpio50: gpclk1_gpio50 {
+	gpclk1_gpio50: gpclk1-gpio50 {
 		pin-gpclk {
 			pins = "gpio50";
 			function = "alt1";
 			bias-disable;
 		};
 	};
-	gpclk2_gpio51: gpclk2_gpio51 {
+	gpclk2_gpio51: gpclk2-gpio51 {
 		pin-gpclk {
 			pins = "gpio51";
 			function = "alt1";
@@ -657,7 +683,7 @@
 		};
 	};
 
-	i2c0_gpio46: i2c0_gpio46 {
+	i2c0_gpio46: i2c0-gpio46 {
 		pin-sda {
 			function = "alt0";
 			pins = "gpio46";
@@ -669,7 +695,7 @@
 			bias-disable;
 		};
 	};
-	i2c1_gpio46: i2c1_gpio46 {
+	i2c1_gpio46: i2c1-gpio46 {
 		pin-sda {
 			function = "alt1";
 			pins = "gpio46";
@@ -681,7 +707,7 @@
 			bias-disable;
 		};
 	};
-	i2c3_gpio2: i2c3_gpio2 {
+	i2c3_gpio2: i2c3-gpio2 {
 		pin-sda {
 			function = "alt5";
 			pins = "gpio2";
@@ -693,7 +719,7 @@
 			bias-disable;
 		};
 	};
-	i2c3_gpio4: i2c3_gpio4 {
+	i2c3_gpio4: i2c3-gpio4 {
 		pin-sda {
 			function = "alt5";
 			pins = "gpio4";
@@ -705,7 +731,7 @@
 			bias-disable;
 		};
 	};
-	i2c4_gpio6: i2c4_gpio6 {
+	i2c4_gpio6: i2c4-gpio6 {
 		pin-sda {
 			function = "alt5";
 			pins = "gpio6";
@@ -717,7 +743,7 @@
 			bias-disable;
 		};
 	};
-	i2c4_gpio8: i2c4_gpio8 {
+	i2c4_gpio8: i2c4-gpio8 {
 		pin-sda {
 			function = "alt5";
 			pins = "gpio8";
@@ -729,7 +755,7 @@
 			bias-disable;
 		};
 	};
-	i2c5_gpio10: i2c5_gpio10 {
+	i2c5_gpio10: i2c5-gpio10 {
 		pin-sda {
 			function = "alt5";
 			pins = "gpio10";
@@ -741,7 +767,7 @@
 			bias-disable;
 		};
 	};
-	i2c5_gpio12: i2c5_gpio12 {
+	i2c5_gpio12: i2c5-gpio12 {
 		pin-sda {
 			function = "alt5";
 			pins = "gpio12";
@@ -753,7 +779,7 @@
 			bias-disable;
 		};
 	};
-	i2c6_gpio0: i2c6_gpio0 {
+	i2c6_gpio0: i2c6-gpio0 {
 		pin-sda {
 			function = "alt5";
 			pins = "gpio0";
@@ -765,7 +791,7 @@
 			bias-disable;
 		};
 	};
-	i2c6_gpio22: i2c6_gpio22 {
+	i2c6_gpio22: i2c6-gpio22 {
 		pin-sda {
 			function = "alt5";
 			pins = "gpio22";
@@ -777,7 +803,7 @@
 			bias-disable;
 		};
 	};
-	i2c_slave_gpio8: i2c_slave_gpio8 {
+	i2c_slave_gpio8: i2c-slave-gpio8 {
 		pins-i2c-slave {
 			pins = "gpio8",
 			       "gpio9",
@@ -787,7 +813,7 @@
 		};
 	};
 
-	jtag_gpio48: jtag_gpio48 {
+	jtag_gpio48: jtag-gpio48 {
 		pins-jtag {
 			pins = "gpio48",
 			       "gpio49",
@@ -799,7 +825,7 @@
 		};
 	};
 
-	mii_gpio28: mii_gpio28 {
+	mii_gpio28: mii-gpio28 {
 		pins-mii {
 			pins = "gpio28",
 			       "gpio29",
@@ -808,7 +834,7 @@
 			function = "alt4";
 		};
 	};
-	mii_gpio36: mii_gpio36 {
+	mii_gpio36: mii-gpio36 {
 		pins-mii {
 			pins = "gpio36",
 			       "gpio37",
@@ -818,7 +844,7 @@
 		};
 	};
 
-	pcm_gpio50: pcm_gpio50 {
+	pcm_gpio50: pcm-gpio50 {
 		pins-pcm {
 			pins = "gpio50",
 			       "gpio51",
@@ -828,63 +854,63 @@
 		};
 	};
 
-	pwm0_0_gpio12: pwm0_0_gpio12 {
+	pwm0_0_gpio12: pwm0-0-gpio12 {
 		pin-pwm {
 			pins = "gpio12";
 			function = "alt0";
 			bias-disable;
 		};
 	};
-	pwm0_0_gpio18: pwm0_0_gpio18 {
+	pwm0_0_gpio18: pwm0-0-gpio18 {
 		pin-pwm {
 			pins = "gpio18";
 			function = "alt5";
 			bias-disable;
 		};
 	};
-	pwm1_0_gpio40: pwm1_0_gpio40 {
+	pwm1_0_gpio40: pwm1-0-gpio40 {
 		pin-pwm {
 			pins = "gpio40";
 			function = "alt0";
 			bias-disable;
 		};
 	};
-	pwm0_1_gpio13: pwm0_1_gpio13 {
+	pwm0_1_gpio13: pwm0-1-gpio13 {
 		pin-pwm {
 			pins = "gpio13";
 			function = "alt0";
 			bias-disable;
 		};
 	};
-	pwm0_1_gpio19: pwm0_1_gpio19 {
+	pwm0_1_gpio19: pwm0-1-gpio19 {
 		pin-pwm {
 			pins = "gpio19";
 			function = "alt5";
 			bias-disable;
 		};
 	};
-	pwm1_1_gpio41: pwm1_1_gpio41 {
+	pwm1_1_gpio41: pwm1-1-gpio41 {
 		pin-pwm {
 			pins = "gpio41";
 			function = "alt0";
 			bias-disable;
 		};
 	};
-	pwm0_1_gpio45: pwm0_1_gpio45 {
+	pwm0_1_gpio45: pwm0-1-gpio45 {
 		pin-pwm {
 			pins = "gpio45";
 			function = "alt0";
 			bias-disable;
 		};
 	};
-	pwm0_0_gpio52: pwm0_0_gpio52 {
+	pwm0_0_gpio52: pwm0-0-gpio52 {
 		pin-pwm {
 			pins = "gpio52";
 			function = "alt1";
 			bias-disable;
 		};
 	};
-	pwm0_1_gpio53: pwm0_1_gpio53 {
+	pwm0_1_gpio53: pwm0-1-gpio53 {
 		pin-pwm {
 			pins = "gpio53";
 			function = "alt1";
@@ -892,7 +918,7 @@
 		};
 	};
 
-	rgmii_gpio35: rgmii_gpio35 {
+	rgmii_gpio35: rgmii-gpio35 {
 		pin-start-stop {
 			pins = "gpio35";
 			function = "alt4";
@@ -902,26 +928,26 @@
 			function = "alt4";
 		};
 	};
-	rgmii_irq_gpio34: rgmii_irq_gpio34 {
+	rgmii_irq_gpio34: rgmii-irq-gpio34 {
 		pin-irq {
 			pins = "gpio34";
 			function = "alt5";
 		};
 	};
-	rgmii_irq_gpio39: rgmii_irq_gpio39 {
+	rgmii_irq_gpio39: rgmii-irq-gpio39 {
 		pin-irq {
 			pins = "gpio39";
 			function = "alt4";
 		};
 	};
-	rgmii_mdio_gpio28: rgmii_mdio_gpio28 {
+	rgmii_mdio_gpio28: rgmii-mdio-gpio28 {
 		pins-mdio {
 			pins = "gpio28",
 			       "gpio29";
 			function = "alt5";
 		};
 	};
-	rgmii_mdio_gpio37: rgmii_mdio_gpio37 {
+	rgmii_mdio_gpio37: rgmii-mdio-gpio37 {
 		pins-mdio {
 			pins = "gpio37",
 			       "gpio38";
@@ -929,7 +955,7 @@
 		};
 	};
 
-	spi0_gpio46: spi0_gpio46 {
+	spi0_gpio46: spi0-gpio46 {
 		pins-spi {
 			pins = "gpio46",
 			       "gpio47",
@@ -938,7 +964,7 @@
 			function = "alt2";
 		};
 	};
-	spi2_gpio46: spi2_gpio46 {
+	spi2_gpio46: spi2-gpio46 {
 		pins-spi {
 			pins = "gpio46",
 			       "gpio47",
@@ -948,7 +974,7 @@
 			function = "alt5";
 		};
 	};
-	spi3_gpio0: spi3_gpio0 {
+	spi3_gpio0: spi3-gpio0 {
 		pins-spi {
 			pins = "gpio0",
 			       "gpio1",
@@ -957,7 +983,7 @@
 			function = "alt3";
 		};
 	};
-	spi4_gpio4: spi4_gpio4 {
+	spi4_gpio4: spi4-gpio4 {
 		pins-spi {
 			pins = "gpio4",
 			       "gpio5",
@@ -966,7 +992,7 @@
 			function = "alt3";
 		};
 	};
-	spi5_gpio12: spi5_gpio12 {
+	spi5_gpio12: spi5-gpio12 {
 		pins-spi {
 			pins = "gpio12",
 			       "gpio13",
@@ -975,7 +1001,7 @@
 			function = "alt3";
 		};
 	};
-	spi6_gpio18: spi6_gpio18 {
+	spi6_gpio18: spi6-gpio18 {
 		pins-spi {
 			pins = "gpio18",
 			       "gpio19",
@@ -985,7 +1011,7 @@
 		};
 	};
 
-	uart2_gpio0: uart2_gpio0 {
+	uart2_gpio0: uart2-gpio0 {
 		pin-tx {
 			pins = "gpio0";
 			function = "alt4";
@@ -997,7 +1023,7 @@
 			bias-pull-up;
 		};
 	};
-	uart2_ctsrts_gpio2: uart2_ctsrts_gpio2 {
+	uart2_ctsrts_gpio2: uart2-ctsrts-gpio2 {
 		pin-cts {
 			pins = "gpio2";
 			function = "alt4";
@@ -1009,7 +1035,7 @@
 			bias-disable;
 		};
 	};
-	uart3_gpio4: uart3_gpio4 {
+	uart3_gpio4: uart3-gpio4 {
 		pin-tx {
 			pins = "gpio4";
 			function = "alt4";
@@ -1021,7 +1047,7 @@
 			bias-pull-up;
 		};
 	};
-	uart3_ctsrts_gpio6: uart3_ctsrts_gpio6 {
+	uart3_ctsrts_gpio6: uart3-ctsrts-gpio6 {
 		pin-cts {
 			pins = "gpio6";
 			function = "alt4";
@@ -1033,7 +1059,7 @@
 			bias-disable;
 		};
 	};
-	uart4_gpio8: uart4_gpio8 {
+	uart4_gpio8: uart4-gpio8 {
 		pin-tx {
 			pins = "gpio8";
 			function = "alt4";
@@ -1045,7 +1071,7 @@
 			bias-pull-up;
 		};
 	};
-	uart4_ctsrts_gpio10: uart4_ctsrts_gpio10 {
+	uart4_ctsrts_gpio10: uart4-ctsrts-gpio10 {
 		pin-cts {
 			pins = "gpio10";
 			function = "alt4";
@@ -1057,7 +1083,7 @@
 			bias-disable;
 		};
 	};
-	uart5_gpio12: uart5_gpio12 {
+	uart5_gpio12: uart5-gpio12 {
 		pin-tx {
 			pins = "gpio12";
 			function = "alt4";
@@ -1069,7 +1095,7 @@
 			bias-pull-up;
 		};
 	};
-	uart5_ctsrts_gpio14: uart5_ctsrts_gpio14 {
+	uart5_ctsrts_gpio14: uart5-ctsrts-gpio14 {
 		pin-cts {
 			pins = "gpio14";
 			function = "alt4";
@@ -1087,6 +1113,14 @@
 	#address-cells = <2>;
 };
 
+&csi0 {
+	interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&csi1 {
+	interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+};
+
 &cma {
 	/*
 	 * arm64 reserves the CMA by default somewhere in ZONE_DMA32,
@@ -1142,6 +1176,7 @@
 };
 
 &uart0 {
+	arm,primecell-periphid = <0x00341011>;
 	interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
 };
 
diff --git a/arch/arm/boot/dts/broadcom/bcm28155-ap.dts b/arch/arm/boot/dts/broadcom/bcm28155-ap.dts
new file mode 100644
index 000000000000..cefaa9a3c45c
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm28155-ap.dts
@@ -0,0 +1,108 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2013 Broadcom Corporation
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+
+#include "bcm11351.dtsi"
+
+/ {
+	model = "BCM28155 AP board";
+	compatible = "brcm,bcm28155-ap", "brcm,bcm11351";
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>; /* 1 GB */
+	};
+};
+
+&bsc1 {
+	clock-frequency = <400000>;
+	status = "okay";
+};
+
+&bsc2 {
+	clock-frequency = <400000>;
+	status = "okay";
+};
+
+&bsc3 {
+	clock-frequency = <400000>;
+	status = "okay";
+};
+
+&pmu_bsc {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	pmu: pmu@8 {
+		compatible = "brcm,bcm59056";
+		interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
+		reg = <0x08>;
+
+		regulators {
+			camldo1_reg: camldo1 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			sdldo_reg: sdldo {
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+			};
+
+			sdxldo_reg: sdxldo {
+				regulator-min-microvolt = <2700000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			usbldo_reg: usbldo {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			iosr1_reg: iosr1 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&pwm {
+	status = "okay";
+};
+
+&sdio2 {
+	non-removable;
+	max-frequency = <48000000>;
+	vmmc-supply = <&camldo1_reg>;
+	vqmmc-supply = <&iosr1_reg>;
+	status = "okay";
+};
+
+&sdio4 {
+	max-frequency = <48000000>;
+	cd-gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&sdldo_reg>;
+	vqmmc-supply = <&sdxldo_reg>;
+	status = "okay";
+};
+
+&uartb {
+	status = "okay";
+};
+
+&usbotg {
+	vusb_d-supply = <&usbldo_reg>;
+	vusb_a-supply = <&iosr1_reg>;
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/bcm2835-common.dtsi b/arch/arm/boot/dts/broadcom/bcm2835-common.dtsi
index c25e797b9060..9261b67dbee1 100644
--- a/arch/arm/boot/dts/bcm2835-common.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm2835-common.dtsi
@@ -8,7 +8,7 @@
 	interrupt-parent = <&intc>;
 
 	soc {
-		dma: dma@7e007000 {
+		dma: dma-controller@7e007000 {
 			compatible = "brcm,bcm2835-dma";
 			reg = <0x7e007000 0xf00>;
 			interrupts = <1 16>,
@@ -62,6 +62,7 @@
 			#reset-cells = <1>;
 			reg = <0x7e100000 0x114>,
 			      <0x7e00a000 0x24>;
+			reg-names = "pm", "asb";
 			clocks = <&clocks BCM2835_CLOCK_V3D>,
 				 <&clocks BCM2835_CLOCK_PERI_IMAGE>,
 				 <&clocks BCM2835_CLOCK_H264>,
@@ -151,41 +152,41 @@
 };
 
 &gpio {
-	i2c_slave_gpio18: i2c_slave_gpio18 {
+	i2c_slave_gpio18: i2c-slave-gpio18 {
 		brcm,pins = <18 19 20 21>;
 		brcm,function = <BCM2835_FSEL_ALT3>;
 	};
 
-	jtag_gpio4: jtag_gpio4 {
+	jtag_gpio4: jtag-gpio4 {
 		brcm,pins = <4 5 6 12 13>;
 		brcm,function = <BCM2835_FSEL_ALT5>;
 	};
 
-	pwm0_gpio12: pwm0_gpio12 {
+	pwm0_gpio12: pwm0-gpio12 {
 		brcm,pins = <12>;
 		brcm,function = <BCM2835_FSEL_ALT0>;
 	};
-	pwm0_gpio18: pwm0_gpio18 {
+	pwm0_gpio18: pwm0-gpio18 {
 		brcm,pins = <18>;
 		brcm,function = <BCM2835_FSEL_ALT5>;
 	};
-	pwm0_gpio40: pwm0_gpio40 {
+	pwm0_gpio40: pwm0-gpio40 {
 		brcm,pins = <40>;
 		brcm,function = <BCM2835_FSEL_ALT0>;
 	};
-	pwm1_gpio13: pwm1_gpio13 {
+	pwm1_gpio13: pwm1-gpio13 {
 		brcm,pins = <13>;
 		brcm,function = <BCM2835_FSEL_ALT0>;
 	};
-	pwm1_gpio19: pwm1_gpio19 {
+	pwm1_gpio19: pwm1-gpio19 {
 		brcm,pins = <19>;
 		brcm,function = <BCM2835_FSEL_ALT5>;
 	};
-	pwm1_gpio41: pwm1_gpio41 {
+	pwm1_gpio41: pwm1-gpio41 {
 		brcm,pins = <41>;
 		brcm,function = <BCM2835_FSEL_ALT0>;
 	};
-	pwm1_gpio45: pwm1_gpio45 {
+	pwm1_gpio45: pwm1-gpio45 {
 		brcm,pins = <45>;
 		brcm,function = <BCM2835_FSEL_ALT0>;
 	};
diff --git a/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts b/arch/arm/boot/dts/broadcom/bcm2835-rpi-a-plus.dts
index 40b9405f1a8e..069b48272aa5 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-a-plus.dts
@@ -2,6 +2,8 @@
 /dts-v1/;
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi-common.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
 
 / {
@@ -12,19 +14,6 @@
 		device_type = "memory";
 		reg = <0 0x10000000>;
 	};
-
-	leds {
-		led-act {
-			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
-		};
-
-		led-pwr {
-			label = "PWR";
-			gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
-			default-state = "keep";
-			linux,default-trigger = "default-on";
-		};
-	};
 };
 
 &gpio {
@@ -32,7 +21,6 @@
 	 * This is based on the unreleased schematic for the Model A+.
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -67,21 +55,21 @@
 			  "GPIO27",
 			  "SDA0",
 			  "SCL0",
-			  "NC", /* GPIO30 */
-			  "NC", /* GPIO31 */
+			  "", /* GPIO30 */
+			  "", /* GPIO31 */
 			  "CAM_GPIO1", /* GPIO32 */
-			  "NC", /* GPIO33 */
-			  "NC", /* GPIO34 */
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
 			  "PWR_LOW_N", /* GPIO35 */
-			  "NC", /* GPIO36 */
-			  "NC", /* GPIO37 */
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
 			  "USB_LIMIT", /* GPIO38 */
-			  "NC", /* GPIO39 */
+			  "", /* GPIO39 */
 			  "PWM0_OUT", /* GPIO40 */
 			  "CAM_GPIO0", /* GPIO41 */
-			  "NC", /* GPIO42 */
-			  "NC", /* GPIO43 */
-			  "NC", /* GPIO44 */
+			  "", /* GPIO42 */
+			  "", /* GPIO43 */
+			  "", /* GPIO44 */
 			  "PWM1_OUT", /* GPIO45 */
 			  "HDMI_HPD_N",
 			  "STATUS_LED",
@@ -93,6 +81,7 @@
 			  "SD_DATA2_R",
 			  "SD_DATA3_R";
 
+	pinctrl-names = "default";
 	pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
 
 	/* I2S interface */
@@ -108,6 +97,19 @@
 	status = "okay";
 };
 
+&led_act {
+	gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
+};
+
+&leds {
+	led-pwr {
+		label = "PWR";
+		gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
+		default-state = "keep";
+		linux,default-trigger = "default-on";
+	};
+};
+
 &pwm {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
diff --git a/arch/arm/boot/dts/bcm2835-rpi-a.dts b/arch/arm/boot/dts/broadcom/bcm2835-rpi-a.dts
index 11edb581dbaf..2726c00431e8 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-a.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-a.dts
@@ -2,6 +2,8 @@
 /dts-v1/;
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi-common.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
 
 / {
@@ -12,12 +14,6 @@
 		device_type = "memory";
 		reg = <0 0x10000000>;
 	};
-
-	leds {
-		led-act {
-			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
-		};
-	};
 };
 
 &gpio {
@@ -26,7 +22,6 @@
 	 * RPI00021 sheet 02
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -42,41 +37,41 @@
 			  "SPI_MISO",
 			  "SPI_MOSI",
 			  "SPI_SCLK",
-			  "NC", /* GPIO12 */
-			  "NC", /* GPIO13 */
+			  "", /* GPIO12 */
+			  "", /* GPIO13 */
 			  /* Serial port */
 			  "TXD0",
 			  "RXD0",
 			  "STATUS_LED_N",
 			  "GPIO17",
 			  "GPIO18",
-			  "NC", /* GPIO19 */
-			  "NC", /* GPIO20 */
+			  "", /* GPIO19 */
+			  "", /* GPIO20 */
 			  "GPIO21",
 			  "GPIO22",
 			  "GPIO23",
 			  "GPIO24",
 			  "GPIO25",
-			  "NC", /* GPIO26 */
+			  "", /* GPIO26 */
 			  "CAM_GPIO0",
 			  /* Binary number representing build/revision */
 			  "CONFIG0",
 			  "CONFIG1",
 			  "CONFIG2",
 			  "CONFIG3",
-			  "NC", /* GPIO32 */
-			  "NC", /* GPIO33 */
-			  "NC", /* GPIO34 */
-			  "NC", /* GPIO35 */
-			  "NC", /* GPIO36 */
-			  "NC", /* GPIO37 */
-			  "NC", /* GPIO38 */
-			  "NC", /* GPIO39 */
+			  "", /* GPIO32 */
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
+			  "", /* GPIO35 */
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
+			  "", /* GPIO38 */
+			  "", /* GPIO39 */
 			  "PWM0_OUT",
-			  "NC", /* GPIO41 */
-			  "NC", /* GPIO42 */
-			  "NC", /* GPIO43 */
-			  "NC", /* GPIO44 */
+			  "", /* GPIO41 */
+			  "", /* GPIO42 */
+			  "", /* GPIO43 */
+			  "", /* GPIO44 */
 			  "PWM1_OUT",
 			  "HDMI_HPD_P",
 			  "SD_CARD_DET",
@@ -88,6 +83,7 @@
 			  "SD_DATA2_R",
 			  "SD_DATA3_R";
 
+	pinctrl-names = "default";
 	pinctrl-0 = <&gpioout &alt0 &i2s_alt2>;
 
 	/* I2S interface */
@@ -103,6 +99,10 @@
 	status = "okay";
 };
 
+&led_act {
+	gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+};
+
 &pwm {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
diff --git a/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts b/arch/arm/boot/dts/broadcom/bcm2835-rpi-b-plus.dts
index 1b435c64bd9c..c57b999a4520 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-b-plus.dts
@@ -2,6 +2,8 @@
 /dts-v1/;
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi-common.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
 #include "bcm283x-rpi-smsc9514.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
 
@@ -13,19 +15,6 @@
 		device_type = "memory";
 		reg = <0 0x20000000>;
 	};
-
-	leds {
-		led-act {
-			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
-		};
-
-		led-pwr {
-			label = "PWR";
-			gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
-			default-state = "keep";
-			linux,default-trigger = "default-on";
-		};
-	};
 };
 
 &gpio {
@@ -34,7 +23,6 @@
 	 * RPI-BPLUS sheet 1
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -69,21 +57,21 @@
 			  "GPIO27",
 			  "SDA0",
 			  "SCL0",
-			  "NC", /* GPIO30 */
+			  "", /* GPIO30 */
 			  "LAN_RUN", /* GPIO31 */
 			  "CAM_GPIO1", /* GPIO32 */
-			  "NC", /* GPIO33 */
-			  "NC", /* GPIO34 */
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
 			  "PWR_LOW_N", /* GPIO35 */
-			  "NC", /* GPIO36 */
-			  "NC", /* GPIO37 */
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
 			  "USB_LIMIT", /* GPIO38 */
-			  "NC", /* GPIO39 */
+			  "", /* GPIO39 */
 			  "PWM0_OUT", /* GPIO40 */
 			  "CAM_GPIO0", /* GPIO41 */
-			  "NC", /* GPIO42 */
-			  "NC", /* GPIO43 */
-			  "ETHCLK", /* GPIO44 */
+			  "", /* GPIO42 */
+			  "", /* GPIO43 */
+			  "ETH_CLK", /* GPIO44 */
 			  "PWM1_OUT", /* GPIO45 */
 			  "HDMI_HPD_N",
 			  "STATUS_LED",
@@ -95,6 +83,7 @@
 			  "SD_DATA2_R",
 			  "SD_DATA3_R";
 
+	pinctrl-names = "default";
 	pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
 
 	/* I2S interface */
@@ -110,6 +99,19 @@
 	status = "okay";
 };
 
+&led_act {
+	gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
+};
+
+&leds {
+	led-pwr {
+		label = "PWR";
+		gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
+		default-state = "keep";
+		linux,default-trigger = "default-on";
+	};
+};
+
 &pwm {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
diff --git a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts b/arch/arm/boot/dts/broadcom/bcm2835-rpi-b-rev2.dts
index a23c25c00eea..ae6d3a9586ab 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-b-rev2.dts
@@ -2,6 +2,8 @@
 /dts-v1/;
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi-common.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
 #include "bcm283x-rpi-smsc9512.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
 
@@ -13,12 +15,6 @@
 		device_type = "memory";
 		reg = <0 0x10000000>;
 	};
-
-	leds {
-		led-act {
-			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
-		};
-	};
 };
 
 &gpio {
@@ -27,7 +23,6 @@
 	 * RPI00022 sheet 02
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -43,40 +38,40 @@
 			  "SPI_MISO",
 			  "SPI_MOSI",
 			  "SPI_SCLK",
-			  "NC", /* GPIO12 */
-			  "NC", /* GPIO13 */
+			  "", /* GPIO12 */
+			  "", /* GPIO13 */
 			  /* Serial port */
 			  "TXD0",
 			  "RXD0",
 			  "STATUS_LED_N",
 			  "GPIO17",
 			  "GPIO18",
-			  "NC", /* GPIO19 */
-			  "NC", /* GPIO20 */
+			  "", /* GPIO19 */
+			  "", /* GPIO20 */
 			  "CAM_GPIO",
 			  "GPIO22",
 			  "GPIO23",
 			  "GPIO24",
 			  "GPIO25",
-			  "NC", /* GPIO26 */
+			  "", /* GPIO26 */
 			  "GPIO27",
 			  "GPIO28",
 			  "GPIO29",
 			  "GPIO30",
 			  "GPIO31",
-			  "NC", /* GPIO32 */
-			  "NC", /* GPIO33 */
-			  "NC", /* GPIO34 */
-			  "NC", /* GPIO35 */
-			  "NC", /* GPIO36 */
-			  "NC", /* GPIO37 */
-			  "NC", /* GPIO38 */
-			  "NC", /* GPIO39 */
+			  "", /* GPIO32 */
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
+			  "", /* GPIO35 */
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
+			  "", /* GPIO38 */
+			  "", /* GPIO39 */
 			  "PWM0_OUT",
-			  "NC", /* GPIO41 */
-			  "NC", /* GPIO42 */
-			  "NC", /* GPIO43 */
-			  "NC", /* GPIO44 */
+			  "", /* GPIO41 */
+			  "", /* GPIO42 */
+			  "", /* GPIO43 */
+			  "", /* GPIO44 */
 			  "PWM1_OUT",
 			  "HDMI_HPD_P",
 			  "SD_CARD_DET",
@@ -88,6 +83,7 @@
 			  "SD_DATA2_R",
 			  "SD_DATA3_R";
 
+	pinctrl-names = "default";
 	pinctrl-0 = <&gpioout &alt0 &i2s_alt2>;
 
 	/* I2S interface */
@@ -103,6 +99,10 @@
 	status = "okay";
 };
 
+&led_act {
+	gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+};
+
 &pwm {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
diff --git a/arch/arm/boot/dts/bcm2835-rpi-b.dts b/arch/arm/boot/dts/broadcom/bcm2835-rpi-b.dts
index 1b63d6b19750..72764be75a79 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-b.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-b.dts
@@ -2,6 +2,8 @@
 /dts-v1/;
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi-common.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
 #include "bcm283x-rpi-smsc9512.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
 
@@ -13,12 +15,6 @@
 		device_type = "memory";
 		reg = <0 0x10000000>;
 	};
-
-	leds {
-		led-act {
-			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
-		};
-	};
 };
 
 &gpio {
@@ -27,7 +23,6 @@
 	 * RPI00021 sheet 02
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -43,41 +38,40 @@
 			  "SPI_MISO",
 			  "SPI_MOSI",
 			  "SPI_SCLK",
-			  "NC", /* GPIO12 */
-			  "NC", /* GPIO13 */
+			  "", /* GPIO12 */
+			  "", /* GPIO13 */
 			  /* Serial port */
 			  "TXD0",
 			  "RXD0",
 			  "STATUS_LED_N",
 			  "GPIO17",
 			  "GPIO18",
-			  "NC", /* GPIO19 */
-			  "NC", /* GPIO20 */
-			  "GPIO21",
+			  "", /* GPIO19 */
+			  "", /* GPIO20 */
+			  "CAM_GPIO0",
 			  "GPIO22",
 			  "GPIO23",
 			  "GPIO24",
 			  "GPIO25",
-			  "NC", /* GPIO26 */
-			  "CAM_GPIO0",
-			  /* Binary number representing build/revision */
-			  "CONFIG0",
-			  "CONFIG1",
-			  "CONFIG2",
-			  "CONFIG3",
-			  "NC", /* GPIO32 */
-			  "NC", /* GPIO33 */
-			  "NC", /* GPIO34 */
-			  "NC", /* GPIO35 */
-			  "NC", /* GPIO36 */
-			  "NC", /* GPIO37 */
-			  "NC", /* GPIO38 */
-			  "NC", /* GPIO39 */
+			  "", /* GPIO26 */
+			  "GPIO27",
+			  "GPIO28",
+			  "GPIO29",
+			  "GPIO30",
+			  "GPIO31",
+			  "", /* GPIO32 */
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
+			  "", /* GPIO35 */
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
+			  "", /* GPIO38 */
+			  "", /* GPIO39 */
 			  "PWM0_OUT",
-			  "NC", /* GPIO41 */
-			  "NC", /* GPIO42 */
-			  "NC", /* GPIO43 */
-			  "NC", /* GPIO44 */
+			  "", /* GPIO41 */
+			  "", /* GPIO42 */
+			  "", /* GPIO43 */
+			  "", /* GPIO44 */
 			  "PWM1_OUT",
 			  "HDMI_HPD_P",
 			  "SD_CARD_DET",
@@ -89,6 +83,7 @@
 			  "SD_DATA2_R",
 			  "SD_DATA3_R";
 
+	pinctrl-names = "default";
 	pinctrl-0 = <&gpioout &alt0>;
 };
 
@@ -98,6 +93,10 @@
 	status = "okay";
 };
 
+&led_act {
+	gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+};
+
 &pwm {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
diff --git a/arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts b/arch/arm/boot/dts/broadcom/bcm2835-rpi-cm1-io1.dts
index a75c882e6575..3f9d198ac3ab 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-cm1-io1.dts
@@ -13,7 +13,6 @@
 	 * This is based on the official GPU firmware DT blob.
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -74,6 +73,7 @@
 			  "SD_DATA2_R",
 			  "SD_DATA3_R";
 
+	pinctrl-names = "default";
 	pinctrl-0 = <&gpioout &alt0>;
 };
 
diff --git a/arch/arm/boot/dts/bcm2835-rpi-cm1.dtsi b/arch/arm/boot/dts/broadcom/bcm2835-rpi-cm1.dtsi
index e4e6b6abbfc1..750cd76948e3 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-cm1.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-cm1.dtsi
@@ -2,6 +2,8 @@
 /dts-v1/;
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi-common.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
 
 / {
 	leds {
@@ -32,6 +34,10 @@
 	};
 };
 
+&led_act {
+	gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
+};
+
 &sdhost {
 	non-removable;
 	vmmc-supply = <&reg_3v3>;
diff --git a/arch/arm/boot/dts/bcm2835-rpi-common.dtsi b/arch/arm/boot/dts/broadcom/bcm2835-rpi-common.dtsi
index 8a55b6cded59..8b3c21d9f333 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-common.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-common.dtsi
@@ -7,6 +7,16 @@
 
 #include <dt-bindings/power/raspberrypi-power.h>
 
+&hdmi {
+	clocks = <&firmware_clocks 9>,
+		 <&firmware_clocks 13>;
+	clock-names = "pixel", "hdmi";
+};
+
 &v3d {
 	power-domains = <&power RPI_POWER_DOMAIN_V3D>;
 };
+
+&vec {
+	clocks = <&firmware_clocks 15>;
+};
diff --git a/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts b/arch/arm/boot/dts/broadcom/bcm2835-rpi-zero-w.dts
index 243236bc1e00..1f0b163e400c 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-zero-w.dts
@@ -6,6 +6,8 @@
 /dts-v1/;
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi-common.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
 #include "bcm283x-rpi-usb-otg.dtsi"
 #include "bcm283x-rpi-wifi-bt.dtsi"
 
@@ -22,12 +24,6 @@
 		/* 8250 auxiliary UART instead of pl011 */
 		stdout-path = "serial1:115200n8";
 	};
-
-	leds {
-		led-act {
-			gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
-		};
-	};
 };
 
 &bt {
@@ -39,7 +35,6 @@
 	 * This is based on the official GPU firmware DT blob.
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -74,19 +69,21 @@
 			  "GPIO27",
 			  "SDA0",
 			  "SCL0",
-			  "NC", /* GPIO30 */
-			  "NC", /* GPIO31 */
-			  "NC", /* GPIO32 */
-			  "NC", /* GPIO33 */
-			  "NC", /* GPIO34 */
-			  "NC", /* GPIO35 */
-			  "NC", /* GPIO36 */
-			  "NC", /* GPIO37 */
-			  "NC", /* GPIO38 */
-			  "NC", /* GPIO39 */
+			  /* Used by BT module */
+			  "CTS0",
+			  "RTS0",
+			  "TXD0",
+			  "RXD0",
+			  /* Used by Wifi */
+			  "SD1_CLK",
+			  "SD1_CMD",
+			  "SD1_DATA0",
+			  "SD1_DATA1",
+			  "SD1_DATA2",
+			  "SD1_DATA3",
 			  "CAM_GPIO1", /* GPIO40 */
 			  "WL_ON", /* GPIO41 */
-			  "NC", /* GPIO42 */
+			  "", /* GPIO42 */
 			  "WIFI_CLK", /* GPIO43 */
 			  "CAM_GPIO0", /* GPIO44 */
 			  "BT_ON", /* GPIO45 */
@@ -100,6 +97,7 @@
 			  "SD_DATA2_R",
 			  "SD_DATA3_R";
 
+	pinctrl-names = "default";
 	pinctrl-0 = <&gpioout &alt0>;
 };
 
@@ -109,7 +107,12 @@
 	status = "okay";
 };
 
+&led_act {
+	gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
+};
+
 &sdhci {
+	pinctrl-names = "default";
 	pinctrl-0 = <&emmc_gpio34 &gpclk2_gpio43>;
 };
 
diff --git a/arch/arm/boot/dts/bcm2835-rpi-zero.dts b/arch/arm/boot/dts/broadcom/bcm2835-rpi-zero.dts
index 6f9b3a908f28..539c19c10946 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-zero.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi-zero.dts
@@ -6,6 +6,8 @@
 /dts-v1/;
 #include "bcm2835.dtsi"
 #include "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi-common.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
 #include "bcm283x-rpi-usb-otg.dtsi"
 
 / {
@@ -16,12 +18,6 @@
 		device_type = "memory";
 		reg = <0 0x20000000>;
 	};
-
-	leds {
-		led-act {
-			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
-		};
-	};
 };
 
 &gpio {
@@ -29,7 +25,6 @@
 	 * This is based on the official GPU firmware DT blob.
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -64,22 +59,22 @@
 			  "GPIO27",
 			  "SDA0",
 			  "SCL0",
-			  "NC", /* GPIO30 */
-			  "NC", /* GPIO31 */
+			  "", /* GPIO30 */
+			  "", /* GPIO31 */
 			  "CAM_GPIO1", /* GPIO32 */
-			  "NC", /* GPIO33 */
-			  "NC", /* GPIO34 */
-			  "NC", /* GPIO35 */
-			  "NC", /* GPIO36 */
-			  "NC", /* GPIO37 */
-			  "NC", /* GPIO38 */
-			  "NC", /* GPIO39 */
-			  "NC", /* GPIO40 */
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
+			  "", /* GPIO35 */
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
+			  "", /* GPIO38 */
+			  "", /* GPIO39 */
+			  "", /* GPIO40 */
 			  "CAM_GPIO0", /* GPIO41 */
-			  "NC", /* GPIO42 */
-			  "NC", /* GPIO43 */
-			  "NC", /* GPIO44 */
-			  "NC", /* GPIO45 */
+			  "", /* GPIO42 */
+			  "", /* GPIO43 */
+			  "", /* GPIO44 */
+			  "", /* GPIO45 */
 			  "HDMI_HPD_N",
 			  "STATUS_LED_N",
 			  /* Used by SD Card */
@@ -90,6 +85,7 @@
 			  "SD_DATA2_R",
 			  "SD_DATA3_R";
 
+	pinctrl-names = "default";
 	pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
 
 	/* I2S interface */
@@ -105,6 +101,10 @@
 	status = "okay";
 };
 
+&led_act {
+	gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
+};
+
 &sdhost {
 	pinctrl-names = "default";
 	pinctrl-0 = <&sdhost_gpio48>;
diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/broadcom/bcm2835-rpi.dtsi
index 87ddcad76083..e9bf41b9f5c1 100644
--- a/arch/arm/boot/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm2835-rpi.dtsi
@@ -1,24 +1,15 @@
 #include <dt-bindings/power/raspberrypi-power.h>
 
 / {
-	leds {
-		compatible = "gpio-leds";
-
-		led-act {
-			label = "ACT";
-			default-state = "keep";
-			linux,default-trigger = "heartbeat";
-		};
-	};
-
 	soc {
 		firmware: firmware {
 			compatible = "raspberrypi,bcm2835-firmware", "simple-mfd";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
 			mboxes = <&mailbox>;
-			dma-ranges;
+
+			firmware_clocks: clocks {
+				compatible = "raspberrypi,firmware-clocks";
+				#clock-cells = <1>;
+			};
 		};
 
 		power: power {
@@ -35,9 +26,21 @@
 	};
 };
 
-&gpio {
-	pinctrl-names = "default";
+&csi0 {
+	clocks = <&clocks BCM2835_CLOCK_CAM0>,
+		 <&firmware_clocks 4>;
+	clock-names = "lp", "vpu";
+	power-domains = <&power RPI_POWER_DOMAIN_UNICAM0>;
+};
 
+&csi1 {
+	clocks = <&clocks BCM2835_CLOCK_CAM1>,
+		 <&firmware_clocks 4>;
+	clock-names = "lp", "vpu";
+	power-domains = <&power RPI_POWER_DOMAIN_UNICAM1>;
+};
+
+&gpio {
 	gpioout: gpioout {
 		brcm,pins = <6>;
 		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
diff --git a/arch/arm/boot/dts/bcm2835.dtsi b/arch/arm/boot/dts/broadcom/bcm2835.dtsi
index 1c90e5a44283..15cb331febbb 100644
--- a/arch/arm/boot/dts/bcm2835.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm2835.dtsi
@@ -1,7 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 #include "bcm283x.dtsi"
 #include "bcm2835-common.dtsi"
-#include "bcm2835-rpi-common.dtsi"
 
 / {
 	compatible = "brcm,bcm2835";
diff --git a/arch/arm/boot/dts/bcm2836-rpi-2-b.dts b/arch/arm/boot/dts/broadcom/bcm2836-rpi-2-b.dts
index d8af8eeac7b6..79918033750e 100644
--- a/arch/arm/boot/dts/bcm2836-rpi-2-b.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2836-rpi-2-b.dts
@@ -2,6 +2,7 @@
 /dts-v1/;
 #include "bcm2836.dtsi"
 #include "bcm2836-rpi.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
 #include "bcm283x-rpi-smsc9514.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
 
@@ -13,19 +14,6 @@
 		device_type = "memory";
 		reg = <0 0x40000000>;
 	};
-
-	leds {
-		led-act {
-			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
-		};
-
-		led-pwr {
-			label = "PWR";
-			gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
-			default-state = "keep";
-			linux,default-trigger = "default-on";
-		};
-	};
 };
 
 &gpio {
@@ -34,7 +22,6 @@
 	 * the official GPU firmware DT blob.
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -83,7 +70,7 @@
 			  "CAM_GPIO0",
 			  "SMPS_SCL",
 			  "SMPS_SDA",
-			  "ETHCLK",
+			  "ETH_CLK",
 			  "PWM1_OUT",
 			  "HDMI_HPD_N",
 			  "STATUS_LED",
@@ -95,6 +82,7 @@
 			  "SD_DATA2_R",
 			  "SD_DATA3_R";
 
+	pinctrl-names = "default";
 	pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
 
 	/* I2S interface */
@@ -110,6 +98,19 @@
 	status = "okay";
 };
 
+&led_act {
+	gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
+};
+
+&leds {
+	led-pwr {
+		label = "PWR";
+		gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
+		default-state = "keep";
+		linux,default-trigger = "default-on";
+	};
+};
+
 &pwm {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
diff --git a/arch/arm/boot/dts/bcm2836-rpi.dtsi b/arch/arm/boot/dts/broadcom/bcm2836-rpi.dtsi
index c4c858b984c6..48b03b55ff56 100644
--- a/arch/arm/boot/dts/bcm2836-rpi.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm2836-rpi.dtsi
@@ -1,5 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 #include "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi-common.dtsi"
 
 &vchiq {
 	compatible = "brcm,bcm2836-vchiq", "brcm,bcm2835-vchiq";
diff --git a/arch/arm/boot/dts/bcm2836.dtsi b/arch/arm/boot/dts/broadcom/bcm2836.dtsi
index 534dacfc4dd5..783fe624ba68 100644
--- a/arch/arm/boot/dts/bcm2836.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm2836.dtsi
@@ -1,7 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 #include "bcm283x.dtsi"
 #include "bcm2835-common.dtsi"
-#include "bcm2835-rpi-common.dtsi"
 
 / {
 	compatible = "brcm,bcm2836";
@@ -11,7 +10,7 @@
 			 <0x40000000 0x40000000 0x00001000>;
 		dma-ranges = <0xc0000000 0x00000000 0x3f000000>;
 
-		local_intc: local_intc@40000000 {
+		local_intc: interrupt-controller@40000000 {
 			compatible = "brcm,bcm2836-l1-intc";
 			reg = <0x40000000 0x100>;
 			interrupt-controller;
@@ -113,6 +112,7 @@
 		 */
 		l2: l2-cache0 {
 			compatible = "cache";
+			cache-unified;
 			cache-size = <0x80000>;
 			cache-line-size = <64>;
 			cache-sets = <1024>; // 512KiB(size)/64(line-size)=8192ways/8-way set
diff --git a/arch/arm/boot/dts/broadcom/bcm2837-rpi-2-b.dts b/arch/arm/boot/dts/broadcom/bcm2837-rpi-2-b.dts
new file mode 100644
index 000000000000..1868cee05853
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm2837-rpi-2-b.dts
@@ -0,0 +1,130 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "bcm2836-rpi.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
+#include "bcm283x-rpi-smsc9514.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+	compatible = "raspberrypi,2-model-b-rev2", "brcm,bcm2837";
+	model = "Raspberry Pi 2 Model B rev 1.2";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x40000000>;
+	};
+};
+
+&gpio {
+	/*
+	 * Taken from rpi_SCH_2b_1p2_reduced.pdf and
+	 * the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "GPIO2",
+			  "GPIO3",
+			  "GPIO4",
+			  "GPIO5",
+			  "GPIO6",
+			  "GPIO7",
+			  "GPIO8",
+			  "GPIO9",
+			  "GPIO10",
+			  "GPIO11",
+			  "GPIO12",
+			  "GPIO13",
+			  "GPIO14",
+			  "GPIO15",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "SDA0",
+			  "SCL0",
+			  "", /* GPIO30 */
+			  "LAN_RUN",
+			  "CAM_GPIO1",
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
+			  "PWR_LOW_N",
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
+			  "USB_LIMIT",
+			  "", /* GPIO39 */
+			  "PWM0_OUT",
+			  "CAM_GPIO0",
+			  "SMPS_SCL",
+			  "SMPS_SDA",
+			  "ETH_CLK",
+			  "PWM1_OUT",
+			  "HDMI_HPD_N",
+			  "STATUS_LED",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
+
+	/* I2S interface */
+	i2s_alt0: i2s_alt0 {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
+};
+
+&led_act {
+	gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
+};
+
+&leds {
+	led-pwr {
+		label = "PWR";
+		gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
+		default-state = "keep";
+		linux,default-trigger = "default-on";
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
+	status = "okay";
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio14>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts b/arch/arm/boot/dts/broadcom/bcm2837-rpi-3-a-plus.dts
index d73daf5bff1d..3548306dfbcb 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2837-rpi-3-a-plus.dts
@@ -2,6 +2,7 @@
 /dts-v1/;
 #include "bcm2837.dtsi"
 #include "bcm2836-rpi.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
 #include "bcm283x-rpi-wifi-bt.dtsi"
 
@@ -18,19 +19,6 @@
 		device_type = "memory";
 		reg = <0 0x20000000>;
 	};
-
-	leds {
-		led-act {
-			gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
-		};
-
-		led-pwr {
-			label = "PWR";
-			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
-			default-state = "keep";
-			linux,default-trigger = "default-on";
-		};
-	};
 };
 
 &firmware {
@@ -55,7 +43,6 @@
 	 * This is mostly based on the official GPU firmware DT blob.
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -125,6 +112,19 @@
 	status = "okay";
 };
 
+&led_act {
+	gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
+};
+
+&leds {
+	led-pwr {
+		label = "PWR";
+		gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+		default-state = "keep";
+		linux,default-trigger = "default-on";
+	};
+};
+
 &pwm {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts b/arch/arm/boot/dts/broadcom/bcm2837-rpi-3-b-plus.dts
index e12938baaf12..2f1800cbc522 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2837-rpi-3-b-plus.dts
@@ -3,6 +3,7 @@
 #include "bcm2837.dtsi"
 #include "bcm2836-rpi.dtsi"
 #include "bcm283x-rpi-lan7515.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
 #include "bcm283x-rpi-wifi-bt.dtsi"
 
@@ -19,19 +20,6 @@
 		device_type = "memory";
 		reg = <0 0x40000000>;
 	};
-
-	leds {
-		led-act {
-			gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
-		};
-
-		led-pwr {
-			label = "PWR";
-			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
-			default-state = "keep";
-			linux,default-trigger = "default-on";
-		};
-	};
 };
 
 &bt {
@@ -45,7 +33,7 @@
 		#gpio-cells = <2>;
 		gpio-line-names = "BT_ON",
 				  "WL_ON",
-				  "STATUS_LED_R",
+				  "PWR_LED_R",
 				  "LAN_RUN",
 				  "",
 				  "CAM_GPIO0",
@@ -61,7 +49,6 @@
 	 * the official GPU firmware DT blob.
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -110,7 +97,7 @@
 			  "SD1_DATA3",
 			  "PWM0_OUT",
 			  "PWM1_OUT",
-			  "ETHCLK",
+			  "ETH_CLK",
 			  "WIFI_CLK",
 			  "SDA0",
 			  "SCL0",
@@ -131,6 +118,19 @@
 	status = "okay";
 };
 
+&led_act {
+	gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
+};
+
+&leds {
+	led-pwr {
+		label = "PWR";
+		gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+		default-state = "keep";
+		linux,default-trigger = "default-on";
+	};
+};
+
 &pwm {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-b.dts b/arch/arm/boot/dts/broadcom/bcm2837-rpi-3-b.dts
index 42b5383b55d8..61270340075c 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-3-b.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2837-rpi-3-b.dts
@@ -2,6 +2,7 @@
 /dts-v1/;
 #include "bcm2837.dtsi"
 #include "bcm2836-rpi.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
 #include "bcm283x-rpi-smsc9514.dtsi"
 #include "bcm283x-rpi-usb-host.dtsi"
 #include "bcm283x-rpi-wifi-bt.dtsi"
@@ -19,12 +20,6 @@
 		device_type = "memory";
 		reg = <0 0x40000000>;
 	};
-
-	leds {
-		led-act {
-			gpios = <&expgpio 2 GPIO_ACTIVE_HIGH>;
-		};
-	};
 };
 
 &bt {
@@ -54,7 +49,6 @@
 	 * the official GPU firmware DT blob.
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -103,7 +97,7 @@
 			  "SD1_DATA3",
 			  "PWM0_OUT",
 			  "PWM1_OUT",
-			  "ETHCLK",
+			  "ETH_CLK",
 			  "WIFI_CLK",
 			  "SDA0",
 			  "SCL0",
@@ -130,6 +124,10 @@
 	status = "okay";
 };
 
+&led_act {
+	gpios = <&expgpio 2 GPIO_ACTIVE_HIGH>;
+};
+
 /* uart0 communicates with the BT module */
 &uart0 {
 	pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/bcm2837-rpi-cm3-io3.dts b/arch/arm/boot/dts/broadcom/bcm2837-rpi-cm3-io3.dts
index 588d9411ceb6..85f54fa595aa 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-cm3-io3.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2837-rpi-cm3-io3.dts
@@ -13,7 +13,6 @@
 	 * This is based on the official GPU firmware DT blob.
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -63,8 +62,8 @@
 			  "GPIO43",
 			  "GPIO44",
 			  "GPIO45",
-			  "GPIO46",
-			  "GPIO47",
+			  "SMPS_SCL",
+			  "SMPS_SDA",
 			  /* Used by eMMC */
 			  "SD_CLK_R",
 			  "SD_CMD_R",
@@ -73,11 +72,12 @@
 			  "SD_DATA2_R",
 			  "SD_DATA3_R";
 
+	pinctrl-names = "default";
 	pinctrl-0 = <&gpioout &alt0>;
 };
 
 &hdmi {
-	hpd-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+	hpd-gpios = <&expgpio 0 GPIO_ACTIVE_LOW>;
 	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/bcm2837-rpi-cm3.dtsi b/arch/arm/boot/dts/broadcom/bcm2837-rpi-cm3.dtsi
index 828a20561b96..1e4e4946b6b6 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-cm3.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm2837-rpi-cm3.dtsi
@@ -9,14 +9,6 @@
 		reg = <0 0x40000000>;
 	};
 
-	leds {
-		/*
-		 * Since there is no upstream GPIO driver yet,
-		 * remove the incomplete node.
-		 */
-		/delete-node/ led-act;
-	};
-
 	reg_3v3: fixed-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "3V3";
@@ -41,12 +33,12 @@
 		#gpio-cells = <2>;
 		gpio-line-names = "HDMI_HPD_N",
 				  "EMMC_EN_N",
-				  "NC",
-				  "NC",
-				  "NC",
-				  "NC",
-				  "NC",
-				  "NC";
+				  "",
+				  "",
+				  "",
+				  "",
+				  "",
+				  "";
 		status = "okay";
 	};
 };
diff --git a/arch/arm/boot/dts/bcm2837-rpi-zero-2-w.dts b/arch/arm/boot/dts/broadcom/bcm2837-rpi-zero-2-w.dts
index 4a768562985e..85cf594724ef 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-zero-2-w.dts
+++ b/arch/arm/boot/dts/broadcom/bcm2837-rpi-zero-2-w.dts
@@ -6,6 +6,7 @@
 /dts-v1/;
 #include "bcm2837.dtsi"
 #include "bcm2836-rpi.dtsi"
+#include "bcm283x-rpi-led-deprecated.dtsi"
 #include "bcm283x-rpi-usb-otg.dtsi"
 #include "bcm283x-rpi-wifi-bt.dtsi"
 
@@ -22,12 +23,6 @@
 		/* 8250 auxiliary UART instead of pl011 */
 		stdout-path = "serial1:115200n8";
 	};
-
-	leds {
-		led-act {
-			gpios = <&gpio 29 GPIO_ACTIVE_LOW>;
-		};
-	};
 };
 
 &bt {
@@ -100,6 +95,7 @@
 			  "SD_DATA2_R",
 			  "SD_DATA3_R";
 
+	pinctrl-names = "default";
 	pinctrl-0 = <&gpioout &alt0>;
 };
 
@@ -109,7 +105,12 @@
 	status = "okay";
 };
 
+&led_act {
+	gpios = <&gpio 29 GPIO_ACTIVE_LOW>;
+};
+
 &sdhci {
+	pinctrl-names = "default";
 	pinctrl-0 = <&emmc_gpio34 &gpclk2_gpio43>;
 };
 
diff --git a/arch/arm/boot/dts/bcm2837.dtsi b/arch/arm/boot/dts/broadcom/bcm2837.dtsi
index 5dbdebc46259..c281697142b1 100644
--- a/arch/arm/boot/dts/bcm2837.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm2837.dtsi
@@ -1,6 +1,5 @@
 #include "bcm283x.dtsi"
 #include "bcm2835-common.dtsi"
-#include "bcm2835-rpi-common.dtsi"
 
 / {
 	compatible = "brcm,bcm2837";
@@ -10,7 +9,7 @@
 			 <0x40000000 0x40000000 0x00001000>;
 		dma-ranges = <0xc0000000 0x00000000 0x3f000000>;
 
-		local_intc: local_intc@40000000 {
+		local_intc: interrupt-controller@40000000 {
 			compatible = "brcm,bcm2836-l1-intc";
 			reg = <0x40000000 0x100>;
 			interrupt-controller;
@@ -115,6 +114,7 @@
 		 */
 		l2: l2-cache0 {
 			compatible = "cache";
+			cache-unified;
 			cache-size = <0x80000>;
 			cache-line-size = <64>;
 			cache-sets = <512>; // 512KiB(size)/64(line-size)=8192ways/16-way set
diff --git a/arch/arm/boot/dts/bcm283x-rpi-lan7515.dtsi b/arch/arm/boot/dts/broadcom/bcm283x-rpi-lan7515.dtsi
index 70bece63f9a7..70bece63f9a7 100644
--- a/arch/arm/boot/dts/bcm283x-rpi-lan7515.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm283x-rpi-lan7515.dtsi
diff --git a/arch/arm/boot/dts/broadcom/bcm283x-rpi-led-deprecated.dtsi b/arch/arm/boot/dts/broadcom/bcm283x-rpi-led-deprecated.dtsi
new file mode 100644
index 000000000000..f83e56de1a72
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm283x-rpi-led-deprecated.dtsi
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/ {
+	/*
+	 * This file provides the now deprecated ACT LED to the
+	 * Raspberry Pi boards. Please don't include this file
+	 * for new boards!
+	 */
+	leds: leds {
+		compatible = "gpio-leds";
+
+		led_act: led-act {
+			label = "ACT";
+			default-state = "keep";
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm283x-rpi-smsc9512.dtsi b/arch/arm/boot/dts/broadcom/bcm283x-rpi-smsc9512.dtsi
index 967e081cb9c2..882b13807075 100644
--- a/arch/arm/boot/dts/bcm283x-rpi-smsc9512.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm283x-rpi-smsc9512.dtsi
@@ -12,7 +12,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		ethernet: usbether@1 {
+		ethernet: ethernet@1 {
 			compatible = "usb424,ec00";
 			reg = <1>;
 		};
diff --git a/arch/arm/boot/dts/bcm283x-rpi-smsc9514.dtsi b/arch/arm/boot/dts/broadcom/bcm283x-rpi-smsc9514.dtsi
index dc7ae776db5f..4273b90b53cc 100644
--- a/arch/arm/boot/dts/bcm283x-rpi-smsc9514.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm283x-rpi-smsc9514.dtsi
@@ -11,7 +11,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		ethernet: usbether@1 {
+		ethernet: ethernet@1 {
 			compatible = "usb424,ec00";
 			reg = <1>;
 		};
diff --git a/arch/arm/boot/dts/bcm283x-rpi-usb-host.dtsi b/arch/arm/boot/dts/broadcom/bcm283x-rpi-usb-host.dtsi
index 73f4ece8dcd0..73f4ece8dcd0 100644
--- a/arch/arm/boot/dts/bcm283x-rpi-usb-host.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm283x-rpi-usb-host.dtsi
diff --git a/arch/arm/boot/dts/bcm283x-rpi-usb-otg.dtsi b/arch/arm/boot/dts/broadcom/bcm283x-rpi-usb-otg.dtsi
index e2fd9610e125..e2fd9610e125 100644
--- a/arch/arm/boot/dts/bcm283x-rpi-usb-otg.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm283x-rpi-usb-otg.dtsi
diff --git a/arch/arm/boot/dts/bcm283x-rpi-usb-peripheral.dtsi b/arch/arm/boot/dts/broadcom/bcm283x-rpi-usb-peripheral.dtsi
index 0ff0e9e25327..0ff0e9e25327 100644
--- a/arch/arm/boot/dts/bcm283x-rpi-usb-peripheral.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm283x-rpi-usb-peripheral.dtsi
diff --git a/arch/arm/boot/dts/bcm283x-rpi-wifi-bt.dtsi b/arch/arm/boot/dts/broadcom/bcm283x-rpi-wifi-bt.dtsi
index 0b64cc19941f..0b64cc19941f 100644
--- a/arch/arm/boot/dts/bcm283x-rpi-wifi-bt.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm283x-rpi-wifi-bt.dtsi
diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/broadcom/bcm283x.dtsi
index c113661a6668..69b0919f1324 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm283x.dtsi
@@ -50,9 +50,9 @@
 
 			trips {
 				cpu-crit {
-					temperature	= <90000>;
-					hysteresis	= <0>;
-					type		= "critical";
+					temperature = <90000>;
+					hysteresis = <0>;
+					type = "critical";
 				};
 			};
 
@@ -135,17 +135,17 @@
 			 * groups only make sense to switch to a
 			 * particular function together.
 			 */
-			dpi_gpio0: dpi_gpio0 {
+			dpi_gpio0: dpi-gpio0 {
 				brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11
 					     12 13 14 15 16 17 18 19
 					     20 21 22 23 24 25 26 27>;
 				brcm,function = <BCM2835_FSEL_ALT2>;
 			};
-			emmc_gpio22: emmc_gpio22 {
+			emmc_gpio22: emmc-gpio22 {
 				brcm,pins = <22 23 24 25 26 27>;
 				brcm,function = <BCM2835_FSEL_ALT3>;
 			};
-			emmc_gpio34: emmc_gpio34 {
+			emmc_gpio34: emmc-gpio34 {
 				brcm,pins = <34 35 36 37 38 39>;
 				brcm,function = <BCM2835_FSEL_ALT3>;
 				brcm,pull = <BCM2835_PUD_OFF
@@ -155,95 +155,95 @@
 					     BCM2835_PUD_UP
 					     BCM2835_PUD_UP>;
 			};
-			emmc_gpio48: emmc_gpio48 {
+			emmc_gpio48: emmc-gpio48 {
 				brcm,pins = <48 49 50 51 52 53>;
 				brcm,function = <BCM2835_FSEL_ALT3>;
 			};
 
-			gpclk0_gpio4: gpclk0_gpio4 {
+			gpclk0_gpio4: gpclk0-gpio4 {
 				brcm,pins = <4>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
-			gpclk1_gpio5: gpclk1_gpio5 {
+			gpclk1_gpio5: gpclk1-gpio5 {
 				brcm,pins = <5>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
-			gpclk1_gpio42: gpclk1_gpio42 {
+			gpclk1_gpio42: gpclk1-gpio42 {
 				brcm,pins = <42>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
-			gpclk1_gpio44: gpclk1_gpio44 {
+			gpclk1_gpio44: gpclk1-gpio44 {
 				brcm,pins = <44>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
-			gpclk2_gpio6: gpclk2_gpio6 {
+			gpclk2_gpio6: gpclk2-gpio6 {
 				brcm,pins = <6>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
-			gpclk2_gpio43: gpclk2_gpio43 {
+			gpclk2_gpio43: gpclk2-gpio43 {
 				brcm,pins = <43>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 				brcm,pull = <BCM2835_PUD_OFF>;
 			};
 
-			i2c0_gpio0: i2c0_gpio0 {
+			i2c0_gpio0: i2c0-gpio0 {
 				brcm,pins = <0 1>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
-			i2c0_gpio28: i2c0_gpio28 {
+			i2c0_gpio28: i2c0-gpio28 {
 				brcm,pins = <28 29>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
-			i2c0_gpio44: i2c0_gpio44 {
+			i2c0_gpio44: i2c0-gpio44 {
 				brcm,pins = <44 45>;
 				brcm,function = <BCM2835_FSEL_ALT1>;
 			};
-			i2c1_gpio2: i2c1_gpio2 {
+			i2c1_gpio2: i2c1-gpio2 {
 				brcm,pins = <2 3>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
-			i2c1_gpio44: i2c1_gpio44 {
+			i2c1_gpio44: i2c1-gpio44 {
 				brcm,pins = <44 45>;
 				brcm,function = <BCM2835_FSEL_ALT2>;
 			};
 
-			jtag_gpio22: jtag_gpio22 {
+			jtag_gpio22: jtag-gpio22 {
 				brcm,pins = <22 23 24 25 26 27>;
 				brcm,function = <BCM2835_FSEL_ALT4>;
 			};
 
-			pcm_gpio18: pcm_gpio18 {
+			pcm_gpio18: pcm-gpio18 {
 				brcm,pins = <18 19 20 21>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
-			pcm_gpio28: pcm_gpio28 {
+			pcm_gpio28: pcm-gpio28 {
 				brcm,pins = <28 29 30 31>;
 				brcm,function = <BCM2835_FSEL_ALT2>;
 			};
 
-			sdhost_gpio48: sdhost_gpio48 {
+			sdhost_gpio48: sdhost-gpio48 {
 				brcm,pins = <48 49 50 51 52 53>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
 
-			spi0_gpio7: spi0_gpio7 {
+			spi0_gpio7: spi0-gpio7 {
 				brcm,pins = <7 8 9 10 11>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
-			spi0_gpio35: spi0_gpio35 {
+			spi0_gpio35: spi0-gpio35 {
 				brcm,pins = <35 36 37 38 39>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
-			spi1_gpio16: spi1_gpio16 {
+			spi1_gpio16: spi1-gpio16 {
 				brcm,pins = <16 17 18 19 20 21>;
 				brcm,function = <BCM2835_FSEL_ALT4>;
 			};
-			spi2_gpio40: spi2_gpio40 {
+			spi2_gpio40: spi2-gpio40 {
 				brcm,pins = <40 41 42 43 44 45>;
 				brcm,function = <BCM2835_FSEL_ALT4>;
 			};
 
-			uart0_gpio14: uart0_gpio14 {
+			uart0_gpio14: uart0-gpio14 {
 				brcm,pins = <14 15>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
 			};
@@ -252,50 +252,50 @@
 			 * people often run uart0 on the two pins
 			 * without flow control.
 			 */
-			uart0_ctsrts_gpio16: uart0_ctsrts_gpio16 {
+			uart0_ctsrts_gpio16: uart0-ctsrts-gpio16 {
 				brcm,pins = <16 17>;
 				brcm,function = <BCM2835_FSEL_ALT3>;
 			};
-			uart0_ctsrts_gpio30: uart0_ctsrts_gpio30 {
+			uart0_ctsrts_gpio30: uart0-ctsrts-gpio30 {
 				brcm,pins = <30 31>;
 				brcm,function = <BCM2835_FSEL_ALT3>;
 				brcm,pull = <BCM2835_PUD_UP BCM2835_PUD_OFF>;
 			};
-			uart0_gpio32: uart0_gpio32 {
+			uart0_gpio32: uart0-gpio32 {
 				brcm,pins = <32 33>;
 				brcm,function = <BCM2835_FSEL_ALT3>;
 				brcm,pull = <BCM2835_PUD_OFF BCM2835_PUD_UP>;
 			};
-			uart0_gpio36: uart0_gpio36 {
+			uart0_gpio36: uart0-gpio36 {
 				brcm,pins = <36 37>;
 				brcm,function = <BCM2835_FSEL_ALT2>;
 			};
-			uart0_ctsrts_gpio38: uart0_ctsrts_gpio38 {
+			uart0_ctsrts_gpio38: uart0-ctsrts-gpio38 {
 				brcm,pins = <38 39>;
 				brcm,function = <BCM2835_FSEL_ALT2>;
 			};
 
-			uart1_gpio14: uart1_gpio14 {
+			uart1_gpio14: uart1-gpio14 {
 				brcm,pins = <14 15>;
 				brcm,function = <BCM2835_FSEL_ALT5>;
 			};
-			uart1_ctsrts_gpio16: uart1_ctsrts_gpio16 {
+			uart1_ctsrts_gpio16: uart1-ctsrts-gpio16 {
 				brcm,pins = <16 17>;
 				brcm,function = <BCM2835_FSEL_ALT5>;
 			};
-			uart1_gpio32: uart1_gpio32 {
+			uart1_gpio32: uart1-gpio32 {
 				brcm,pins = <32 33>;
 				brcm,function = <BCM2835_FSEL_ALT5>;
 			};
-			uart1_ctsrts_gpio30: uart1_ctsrts_gpio30 {
+			uart1_ctsrts_gpio30: uart1-ctsrts-gpio30 {
 				brcm,pins = <30 31>;
 				brcm,function = <BCM2835_FSEL_ALT5>;
 			};
-			uart1_gpio40: uart1_gpio40 {
+			uart1_gpio40: uart1-gpio40 {
 				brcm,pins = <40 41>;
 				brcm,function = <BCM2835_FSEL_ALT5>;
 			};
-			uart1_ctsrts_gpio42: uart1_ctsrts_gpio42 {
+			uart1_ctsrts_gpio42: uart1-ctsrts-gpio42 {
 				brcm,pins = <42 43>;
 				brcm,function = <BCM2835_FSEL_ALT5>;
 			};
@@ -352,8 +352,6 @@
 			clocks = <&clocks BCM2835_CLOCK_VPU>,
 				 <&clocks BCM2835_CLOCK_DPI>;
 			clock-names = "core", "pixel";
-			#address-cells = <1>;
-			#size-cells = <0>;
 			status = "disabled";
 		};
 
@@ -418,7 +416,7 @@
 			clocks = <&clocks BCM2835_CLOCK_PWM>;
 			assigned-clocks = <&clocks BCM2835_CLOCK_PWM>;
 			assigned-clock-rates = <10000000>;
-			#pwm-cells = <2>;
+			#pwm-cells = <3>;
 			status = "disabled";
 		};
 
@@ -456,6 +454,30 @@
 			status = "disabled";
 		};
 
+		csi0: csi@7e800000 {
+			compatible = "brcm,bcm2835-unicam";
+			reg = <0x7e800000 0x800>,
+			      <0x7e802000 0x4>;
+			reg-names = "unicam", "cmi";
+			interrupts = <2 6>;
+			brcm,num-data-lanes = <2>;
+			status = "disabled";
+			port {
+			};
+		};
+
+		csi1: csi@7e801000 {
+			compatible = "brcm,bcm2835-unicam";
+			reg = <0x7e801000 0x800>,
+			      <0x7e802004 0x4>;
+			reg-names = "unicam", "cmi";
+			interrupts = <2 7>;
+			brcm,num-data-lanes = <4>;
+			status = "disabled";
+			port {
+			};
+		};
+
 		i2c1: i2c@7e804000 {
 			compatible = "brcm,bcm2835-i2c";
 			reg = <0x7e804000 0x1000>;
diff --git a/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts b/arch/arm/boot/dts/broadcom/bcm4708-asus-rt-ac56u.dts
index 8ed403767540..c80ac16ad949 100644
--- a/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4708-asus-rt-ac56u.dts
@@ -28,40 +28,39 @@
 	leds {
 		compatible = "gpio-leds";
 
-		usb3 {
+		led-usb3 {
 			label = "bcm53xx:blue:usb3";
 			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
 		};
 
-		wan {
+		led-wan {
 			label = "bcm53xx:blue:wan";
 			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
 		};
 
-		lan {
+		led-lan {
 			label = "bcm53xx:blue:lan";
 			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
 		};
 
-		power {
+		led-power {
 			label = "bcm53xx:blue:power";
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		all {
+		led-all {
 			label = "bcm53xx:blue:all";
 			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:blue:2ghz";
 			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
 		};
 
-
-		usb2 {
+		led-usb2 {
 			label = "bcm53xx:blue:usb2";
 			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
 		};
@@ -70,19 +69,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts b/arch/arm/boot/dts/broadcom/bcm4708-asus-rt-ac68u.dts
index 667b118ba4ee..3fe17bd7b86d 100644
--- a/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4708-asus-rt-ac68u.dts
@@ -28,24 +28,24 @@
 	leds {
 		compatible = "gpio-leds";
 
-		usb2 {
+		led-usb2 {
 			label = "bcm53xx:blue:usb2";
 			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
 		};
 
-		power {
+		led-power {
 			label = "bcm53xx:blue:power";
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		logo {
+		led-logo {
 			label = "bcm53xx:white:logo";
 			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		usb3 {
+		led-usb3 {
 			label = "bcm53xx:blue:usb3";
 			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
 		};
@@ -54,25 +54,25 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		brightness {
+		button-brightness {
 			label = "Backlight";
 			linux,code = <KEY_BRIGHTNESS_ZERO>;
 			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
 		};
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/broadcom/bcm4708-buffalo-wxr-1750dhp.dts b/arch/arm/boot/dts/broadcom/bcm4708-buffalo-wxr-1750dhp.dts
new file mode 100644
index 000000000000..f5c95c9a712e
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm4708-buffalo-wxr-1750dhp.dts
@@ -0,0 +1,138 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Author: Taishi Shimizu <s.taishi14142@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+	compatible = "buffalo,wxr-1750dhp", "brcm,bcm4708";
+	model = "Buffalo WXR-1750DHP";
+
+	memory@0 {
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+		device_type = "memory";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-aoss {
+			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
+			label = "AOSS";
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+
+		/* GPIO 3 is a switch button with AUTO / MANUAL. */
+		button-manual {
+			gpios = <&chipcommon 3 GPIO_ACTIVE_HIGH>;
+			label = "MANUAL";
+			linux,code = <BTN_0>;
+			linux,input-type = <EV_SW>;
+		};
+
+		button-restart {
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+		};
+
+		/* GPIO 8 and 9 are a tri-state switch button with
+		 * ROUTER / AP / WB.
+		 */
+		button-router {
+			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
+			label = "ROUTER";
+			linux,code = <BTN_1>;
+			linux,input-type = <EV_SW>;
+		};
+
+		button-wb {
+			gpios = <&chipcommon 9 GPIO_ACTIVE_LOW>;
+			label = "WB";
+			linux,code = <BTN_2>;
+			linux,input-type = <EV_SW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-internet {
+			color = <LED_COLOR_ID_WHITE>;
+			function = "internet";
+			gpios = <&chipcommon 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-power0 {
+			color = <LED_COLOR_ID_AMBER>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&chipcommon 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-power1 {
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-router0 {
+			color = <LED_COLOR_ID_AMBER>;
+			function = "router";
+			gpios = <&chipcommon 14 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-router1 {
+			color = <LED_COLOR_ID_WHITE>;
+			function = "router";
+			gpios = <&chipcommon 15 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-usb {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_USB;
+			gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "usbport";
+			trigger-sources = <&xhci_port1 &ehci_port1 &ohci_port1>;
+		};
+	};
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "wan";
+		};
+
+		port@1 {
+			label = "lan4";
+		};
+
+		port@2 {
+			label = "lan3";
+		};
+
+		port@3 {
+			label = "lan2";
+		};
+
+		port@4 {
+			label = "lan1";
+		};
+	};
+};
+
+&usb3 {
+	vcc-gpio = <&chipcommon 10 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3_phy {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm4708-buffalo-wzr-1166dhp-common.dtsi b/arch/arm/boot/dts/broadcom/bcm4708-buffalo-wzr-1166dhp-common.dtsi
new file mode 100644
index 000000000000..9f9084269ef5
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm4708-buffalo-wzr-1166dhp-common.dtsi
@@ -0,0 +1,193 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Buffalo WZR-1166DHP and WZR-1166DHP2
+ *
+ * Copyright (C) 2014 Rafał Miłecki <zajec5@gmail.com>
+ * Copyright (C) 2022 SHIMAMOTO Takayoshi <takayoshi.shimamoto.360@gmail.com>
+ */
+
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+	spi {
+		compatible = "spi-gpio";
+		num-chipselects = <1>;
+		sck-gpios = <&chipcommon 7 0>;
+		mosi-gpios = <&chipcommon 4 0>;
+		cs-gpios = <&chipcommon 6 0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hc595: gpio_spi@0 {
+			compatible = "fairchild,74hc595";
+			reg = <0>;
+			registers-number = <1>;
+			spi-max-frequency = <100000>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-usb {
+			/* label = "bcm53xx:blue:usb"; */
+			function = LED_FUNCTION_USB;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&hc595 0 GPIO_ACTIVE_HIGH>;
+			trigger-sources = <&ohci_port1>, <&ehci_port1>,
+					  <&xhci_port1>, <&ohci_port2>,
+					  <&ehci_port2>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-power0 {
+			/* label = "bcm53xx:red:power"; */
+			function = LED_FUNCTION_FAULT;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&hc595 1 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-power1 {
+			/* label = "bcm53xx:white:power"; */
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_WHITE>;
+			gpios = <&hc595 2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-router0 {
+			/*  label = "bcm53xx:blue:router"; */
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&hc595 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-router1 {
+			/* label = "bcm53xx:amber:router"; */
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_AMBER>;
+			gpios = <&hc595 4 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wan {
+			/* label = "bcm53xx:blue:wan"; */
+			function = LED_FUNCTION_WAN;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&hc595 5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-wireless0 {
+			/* label = "bcm53xx:blue:wireless"; */
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&hc595 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wireless1 {
+			/* label = "bcm53xx:amber:wireless"; */
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_AMBER>;
+			gpios = <&hc595 7 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+
+		button-aoss {
+			label = "AOSS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 12 GPIO_ACTIVE_LOW>;
+		};
+
+		/* Commit mode set by switch? */
+		button-mode {
+			label = "Mode";
+			linux,code = <KEY_SETUP>;
+			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
+		};
+
+		/* Switch: AP mode */
+		button-sw-ap {
+			label = "AP";
+			linux,code = <BTN_0>;
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+		};
+
+		button-eject {
+			label = "USB eject";
+			linux,code = <KEY_EJECTCD>;
+			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&usb2 {
+	vcc-gpio = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3 {
+	vcc-gpio = <&chipcommon 10 GPIO_ACTIVE_LOW>;
+};
+
+&spi_nor {
+	status = "okay";
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan1";
+		};
+
+		port@1 {
+			label = "lan2";
+		};
+
+		port@2 {
+			label = "lan3";
+		};
+
+		port@3 {
+			label = "lan4";
+		};
+
+		port@4 {
+			label = "wan";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm4708-buffalo-wzr-1166dhp.dts b/arch/arm/boot/dts/broadcom/bcm4708-buffalo-wzr-1166dhp.dts
new file mode 100644
index 000000000000..8e506269fa1a
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm4708-buffalo-wzr-1166dhp.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree Bindigs for Buffalo WZR-1166DHP
+ *
+ * Copyright (C) 2022 SHIMAMOTO Takayoshi <takayoshi.shimamoto.360@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4708-buffalo-wzr-1166dhp-common.dtsi"
+
+/ {
+	compatible = "buffalo,wzr-1166dhp", "brcm,bcm4708";
+	model = "Buffalo WZR-1166DHP";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x18000000>;
+	};
+
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm4708-buffalo-wzr-1166dhp2.dts b/arch/arm/boot/dts/broadcom/bcm4708-buffalo-wzr-1166dhp2.dts
new file mode 100644
index 000000000000..596129027074
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm4708-buffalo-wzr-1166dhp2.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree Bindigs for Buffalo WZR-1166DHP2
+ *
+ * Copyright (C) 2022 SHIMAMOTO Takayoshi <takayoshi.shimamoto.360@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4708-buffalo-wzr-1166dhp-common.dtsi"
+
+/ {
+	compatible = "buffalo,wzr-1166dhp2", "brcm,bcm4708";
+	model = "Buffalo WZR-1166DHP2";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+};
diff --git a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts b/arch/arm/boot/dts/broadcom/bcm4708-buffalo-wzr-1750dhp.dts
index ff31ce45831a..95ef6ca7210b 100644
--- a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4708-buffalo-wzr-1750dhp.dts
@@ -28,8 +28,8 @@
 	spi {
 		compatible = "spi-gpio";
 		num-chipselects = <1>;
-		gpio-sck = <&chipcommon 7 0>;
-		gpio-mosi = <&chipcommon 4 0>;
+		sck-gpios = <&chipcommon 7 0>;
+		mosi-gpios = <&chipcommon 4 0>;
 		cs-gpios = <&chipcommon 6 0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -49,7 +49,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		usb {
+		led-usb {
 			label = "bcm53xx:blue:usb";
 			gpios = <&hc595 0 GPIO_ACTIVE_HIGH>;
 			trigger-sources = <&ohci_port1>, <&ehci_port1>,
@@ -58,40 +58,40 @@
 			linux,default-trigger = "usbport";
 		};
 
-		power0 {
+		led-power0 {
 			label = "bcm53xx:red:power";
 			gpios = <&hc595 1 GPIO_ACTIVE_HIGH>;
 		};
 
-		power1 {
+		led-power1 {
 			label = "bcm53xx:white:power";
 			gpios = <&hc595 2 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		router0 {
+		led-router0 {
 			label = "bcm53xx:blue:router";
 			gpios = <&hc595 3 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		router1 {
+		led-router1 {
 			label = "bcm53xx:amber:router";
 			gpios = <&hc595 4 GPIO_ACTIVE_HIGH>;
 		};
 
-		wan {
+		led-wan {
 			label = "bcm53xx:blue:wan";
 			gpios = <&hc595 5 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		wireless0 {
+		led-wireless0 {
 			label = "bcm53xx:blue:wireless";
 			gpios = <&hc595 6 GPIO_ACTIVE_HIGH>;
 		};
 
-		wireless1 {
+		led-wireless1 {
 			label = "bcm53xx:amber:wireless";
 			gpios = <&hc595 7 GPIO_ACTIVE_HIGH>;
 		};
@@ -100,33 +100,33 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
 		};
 
-		aoss {
+		button-aoss {
 			label = "AOSS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 12 GPIO_ACTIVE_LOW>;
 		};
 
 		/* Commit mode set by switch? */
-		mode {
+		button-mode {
 			label = "Mode";
 			linux,code = <KEY_SETUP>;
 			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
 		};
 
 		/* Switch: AP mode */
-		sw_ap {
+		button-sw-ap {
 			label = "AP";
 			linux,code = <BTN_0>;
 			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
 		};
 
-		eject {
+		button-eject {
 			label = "USB eject";
 			linux,code = <KEY_EJECTCD>;
 			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4708-linksys-ea6300-v1.dts b/arch/arm/boot/dts/broadcom/bcm4708-linksys-ea6300-v1.dts
index 5bac1e15775a..0ed25bf71f0d 100644
--- a/arch/arm/boot/dts/bcm4708-linksys-ea6300-v1.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4708-linksys-ea6300-v1.dts
@@ -29,13 +29,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4708-linksys-ea6500-v2.dts b/arch/arm/boot/dts/broadcom/bcm4708-linksys-ea6500-v2.dts
index cd797b4202ad..0454423fe166 100644
--- a/arch/arm/boot/dts/bcm4708-linksys-ea6500-v2.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4708-linksys-ea6500-v2.dts
@@ -19,19 +19,20 @@
 
 	memory@0 {
 		device_type = "memory";
-		reg = <0x00000000 0x08000000>;
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
 	};
 
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4708-luxul-xap-1510.dts b/arch/arm/boot/dts/broadcom/bcm4708-luxul-xap-1510.dts
index 5b4a481be4f4..72e960c888ac 100644
--- a/arch/arm/boot/dts/bcm4708-luxul-xap-1510.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4708-luxul-xap-1510.dts
@@ -8,7 +8,7 @@
 #include "bcm4708.dtsi"
 
 / {
-	compatible = "luxul,xap-1510v1", "brcm,bcm4708";
+	compatible = "luxul,xap-1510-v1", "brcm,bcm4708";
 	model = "Luxul XAP-1510 V1";
 
 	chosen {
@@ -20,22 +20,30 @@
 		reg = <0x00000000 0x08000000>;
 	};
 
+	nvram@1eff0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 
-		5ghz {
+		led-5ghz {
 			label = "bcm53xx:blue:5ghz";
 			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
 		};
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:blue:2ghz";
 			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
 		};
 
-		status {
+		led-status {
 			label = "bcm53xx:green:status";
 			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "timer";
@@ -45,7 +53,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
@@ -53,6 +61,11 @@
 	};
 };
 
+&gmac0 {
+	nvmem-cells = <&et0macaddr>;
+	nvmem-cell-names = "mac-address";
+};
+
 &spi_nor {
 	status = "okay";
 };
@@ -62,19 +75,23 @@
 
 	ports {
 		port@0 {
-			reg = <0>;
 			label = "poe";
 		};
 
 		port@4 {
-			reg = <4>;
 			label = "lan";
 		};
 
 		port@5 {
-			reg = <5>;
 			label = "cpu";
-			ethernet = <&gmac0>;
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts b/arch/arm/boot/dts/broadcom/bcm4708-luxul-xwc-1000.dts
index c81944cd6d0b..750e17482371 100644
--- a/arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4708-luxul-xwc-1000.dts
@@ -24,6 +24,14 @@
 		reg = <0x00000000 0x08000000>;
 	};
 
+	nvram@1eff0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+		};
+	};
+
 	nand_controller: nand-controller@18028000 {
 		nand@0 {
 			partitions {
@@ -42,7 +50,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		status {
+		led-status {
 			label = "bcm53xx:green:status";
 			gpios = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "timer";
@@ -52,7 +60,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
@@ -60,6 +68,11 @@
 	};
 };
 
+&gmac0 {
+	nvmem-cells = <&et0macaddr>;
+	nvmem-cell-names = "mac-address";
+};
+
 &spi_nor {
 	status = "okay";
 };
@@ -69,14 +82,19 @@
 
 	ports {
 		port@4 {
-			reg = <4>;
 			label = "lan";
 		};
 
 		port@5 {
-			reg = <5>;
 			label = "cpu";
-			ethernet = <&gmac0>;
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/bcm4708-netgear-r6250.dts b/arch/arm/boot/dts/broadcom/bcm4708-netgear-r6250.dts
index 43a5d675dd67..2bdbc7d18b0e 100644
--- a/arch/arm/boot/dts/bcm4708-netgear-r6250.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4708-netgear-r6250.dts
@@ -13,7 +13,7 @@
 #include "bcm5301x-nand-cs0-bch8.dtsi"
 
 / {
-	compatible = "netgear,r6250v1", "brcm,bcm4708";
+	compatible = "netgear,r6250-v1", "brcm,bcm4708";
 	model = "Netgear R6250 V1 (BCM4708)";
 
 	chosen {
@@ -29,24 +29,24 @@
 	leds {
 		compatible = "gpio-leds";
 
-		logo {
+		led-logo {
 			label = "bcm53xx:white:logo";
 			gpios = <&chipcommon 1 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		power0 {
+		led-power0 {
 			label = "bcm53xx:green:power";
 			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		power1 {
+		led-power1 {
 			label = "bcm53xx:amber:power";
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 		};
 
-		usb {
+		led-usb {
 			label = "bcm53xx:blue:usb";
 			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
 			trigger-sources = <&ohci_port1>, <&ehci_port1>,
@@ -54,7 +54,7 @@
 			linux,default-trigger = "usbport";
 		};
 
-		wireless {
+		led-wireless {
 			label = "bcm53xx:blue:wireless";
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
 		};
@@ -63,19 +63,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
 		};
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
@@ -100,34 +100,35 @@
 
 	ports {
 		port@0 {
-			reg = <0>;
 			label = "lan4";
 		};
 
 		port@1 {
-			reg = <1>;
 			label = "lan3";
 		};
 
 		port@2 {
-			reg = <2>;
 			label = "lan2";
 		};
 
 		port@3 {
-			reg = <3>;
 			label = "lan1";
 		};
 
 		port@4 {
-			reg = <4>;
 			label = "wan";
 		};
 
 		port@5 {
-			reg = <5>;
 			label = "cpu";
-			ethernet = <&gmac0>;
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts b/arch/arm/boot/dts/broadcom/bcm4708-netgear-r6300-v2.dts
index 4c60eda296d9..77396730bdd3 100644
--- a/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4708-netgear-r6300-v2.dts
@@ -12,7 +12,7 @@
 #include "bcm5301x-nand-cs0-bch8.dtsi"
 
 / {
-	compatible = "netgear,r6300v2", "brcm,bcm4708";
+	compatible = "netgear,r6300-v2", "brcm,bcm4708";
 	model = "Netgear R6300 V2 (BCM4708)";
 
 	chosen {
@@ -28,29 +28,29 @@
 	leds {
 		compatible = "gpio-leds";
 
-		logo {
+		led-logo {
 			label = "bcm53xx:white:logo";
 			gpios = <&chipcommon 1 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		power0 {
+		led-power0 {
 			label = "bcm53xx:green:power";
 			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
 		};
 
-		power1 {
+		led-power1 {
 			label = "bcm53xx:amber:power";
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		usb {
+		led-usb {
 			label = "bcm53xx:blue:usb";
 			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
 		};
 
-		wireless {
+		led-wireless {
 			label = "bcm53xx:blue:wireless";
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
 		};
@@ -59,19 +59,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
 		};
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts b/arch/arm/boot/dts/broadcom/bcm4708-smartrg-sr400ac.dts
index 9ca6d1b2590d..b226bef3369c 100644
--- a/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4708-smartrg-sr400ac.dts
@@ -28,64 +28,64 @@
 	leds {
 		compatible = "gpio-leds";
 
-		power-white {
+		led-power-white {
 			label = "bcm53xx:white:power";
 			gpios = <&chipcommon 1 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		power-amber {
+		led-power-amber {
 			label = "bcm53xx:amber:power";
 			gpios = <&chipcommon 2 GPIO_ACTIVE_HIGH>;
 		};
 
-		usb2 {
+		led-usb2 {
 			label = "bcm53xx:white:usb2";
 			gpios = <&chipcommon 3 GPIO_ACTIVE_HIGH>;
 			trigger-sources = <&ohci_port2>, <&ehci_port2>;
 			linux,default-trigger = "usbport";
 		};
 
-		usb3-white {
+		led-usb3-white {
 			label = "bcm53xx:white:usb3";
 			gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>;
 			trigger-sources = <&xhci_port1>;
 			linux,default-trigger = "usbport";
 		};
 
-		usb3-green {
+		led-usb3-green {
 			label = "bcm53xx:green:usb3";
 			gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
 			trigger-sources = <&ohci_port1>, <&ehci_port1>;
 			linux,default-trigger = "usbport";
 		};
 
-		wps {
+		led-wps {
 			label = "bcm53xx:white:wps";
 			gpios = <&chipcommon 6 GPIO_ACTIVE_HIGH>;
 		};
 
-		status-red {
+		led-status-red {
 			label = "bcm53xx:red:status";
 			gpios = <&chipcommon 8 GPIO_ACTIVE_HIGH>;
 		};
 
-		status-green {
+		led-status-green {
 			label = "bcm53xx:green:status";
 			gpios = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
 		};
 
-		status-blue {
+		led-status-blue {
 			label = "bcm53xx:blue:status";
 			gpios = <&chipcommon 10 GPIO_ACTIVE_HIGH>;
 		};
 
-		wan-white {
+		led-wan-white {
 			label = "bcm53xx:white:wan";
 			gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
 		};
 
-		wan-red {
+		led-wan-red {
 			label = "bcm53xx:red:wan";
 			gpios = <&chipcommon 13 GPIO_ACTIVE_HIGH>;
 		};
@@ -94,19 +94,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
@@ -123,34 +123,35 @@
 
 	ports {
 		port@0 {
-			reg = <0>;
 			label = "lan4";
 		};
 
 		port@1 {
-			reg = <1>;
 			label = "lan3";
 		};
 
 		port@2 {
-			reg = <2>;
 			label = "lan2";
 		};
 
 		port@3 {
-			reg = <3>;
 			label = "lan1";
 		};
 
 		port@4 {
-			reg = <4>;
 			label = "wan";
 		};
 
 		port@5 {
-			reg = <5>;
 			label = "cpu";
-			ethernet = <&gmac0>;
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/bcm4708.dtsi b/arch/arm/boot/dts/broadcom/bcm4708.dtsi
index 1a19e97a987d..1a19e97a987d 100644
--- a/arch/arm/boot/dts/bcm4708.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm4708.dtsi
diff --git a/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts b/arch/arm/boot/dts/broadcom/bcm47081-asus-rt-n18u.dts
index 0e273c598732..3854db0118a9 100644
--- a/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47081-asus-rt-n18u.dts
@@ -28,30 +28,30 @@
 	leds {
 		compatible = "gpio-leds";
 
-		power {
+		led-power {
 			label = "bcm53xx:blue:power";
 			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		usb2 {
+		led-usb2 {
 			label = "bcm53xx:blue:usb2";
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 		};
 
-		wan {
+		led-wan {
 			label = "bcm53xx:blue:wan";
 			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		lan {
+		led-lan {
 			label = "bcm53xx:blue:lan";
 			gpios = <&chipcommon 9 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		usb3 {
+		led-usb3 {
 			label = "bcm53xx:blue:usb3";
 			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
 		};
@@ -60,13 +60,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts b/arch/arm/boot/dts/broadcom/bcm47081-buffalo-wzr-600dhp2.dts
index d00495a8b6fc..192b8db5a89c 100644
--- a/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47081-buffalo-wzr-600dhp2.dts
@@ -28,8 +28,8 @@
 	spi {
 		compatible = "spi-gpio";
 		num-chipselects = <1>;
-		gpio-sck = <&chipcommon 7 0>;
-		gpio-mosi = <&chipcommon 4 0>;
+		sck-gpios = <&chipcommon 7 0>;
+		mosi-gpios = <&chipcommon 4 0>;
 		cs-gpios = <&chipcommon 6 0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -49,40 +49,40 @@
 	leds {
 		compatible = "gpio-leds";
 
-		power0 {
+		led-power0 {
 			label = "bcm53xx:green:power";
 			gpios = <&hc595 1 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		power1 {
+		led-power1 {
 			label = "bcm53xx:red:power";
 			gpios = <&hc595 2 GPIO_ACTIVE_HIGH>;
 		};
 
-		router0 {
+		led-router0 {
 			label = "bcm53xx:green:router";
 			gpios = <&hc595 3 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		router1 {
+		led-router1 {
 			label = "bcm53xx:amber:router";
 			gpios = <&hc595 4 GPIO_ACTIVE_HIGH>;
 		};
 
-		wan {
+		led-wan {
 			label = "bcm53xx:green:wan";
 			gpios = <&hc595 5 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		wireless0 {
+		led-wireless0 {
 			label = "bcm53xx:green:wireless";
 			gpios = <&hc595 6 GPIO_ACTIVE_HIGH>;
 		};
 
-		wireless1 {
+		led-wireless1 {
 			label = "bcm53xx:amber:wireless";
 			gpios = <&hc595 7 GPIO_ACTIVE_HIGH>;
 		};
@@ -91,26 +91,26 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		aoss {
+		button-aoss {
 			label = "AOSS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 9 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
 		};
 
 		/* Switch device mode? */
-		mode {
+		button-mode {
 			label = "Mode";
 			linux,code = <KEY_SETUP>;
 			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
 		};
 
-		eject {
+		button-eject {
 			label = "USB eject";
 			linux,code = <KEY_EJECTCD>;
 			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
@@ -123,34 +123,35 @@
 
 	ports {
 		port@0 {
-			reg = <0>;
 			label = "lan1";
 		};
 
 		port@1 {
-			reg = <1>;
 			label = "lan2";
 		};
 
 		port@2 {
-			reg = <2>;
 			label = "lan3";
 		};
 
 		port@3 {
-			reg = <3>;
 			label = "lan4";
 		};
 
 		port@4 {
-			reg = <4>;
 			label = "wan";
 		};
 
 		port@5 {
-			reg = <5>;
 			label = "cpu";
-			ethernet = <&gmac0>;
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts b/arch/arm/boot/dts/broadcom/bcm47081-buffalo-wzr-900dhp.dts
index 8b1a05a0f1a1..7655e4ff2d1c 100644
--- a/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47081-buffalo-wzr-900dhp.dts
@@ -28,8 +28,8 @@
 	spi {
 		compatible = "spi-gpio";
 		num-chipselects = <1>;
-		gpio-sck = <&chipcommon 7 0>;
-		gpio-mosi = <&chipcommon 4 0>;
+		sck-gpios = <&chipcommon 7 0>;
+		mosi-gpios = <&chipcommon 4 0>;
 		cs-gpios = <&chipcommon 6 0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -49,45 +49,45 @@
 	leds {
 		compatible = "gpio-leds";
 
-		usb {
+		led-usb {
 			label = "bcm53xx:green:usb";
 			gpios = <&hc595 0 GPIO_ACTIVE_HIGH>;
 		};
 
-		power0 {
+		led-power0 {
 			label = "bcm53xx:green:power";
 			gpios = <&hc595 1 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		power1 {
+		led-power1 {
 			label = "bcm53xx:red:power";
 			gpios = <&hc595 2 GPIO_ACTIVE_HIGH>;
 		};
 
-		router0 {
+		led-router0 {
 			label = "bcm53xx:green:router";
 			gpios = <&hc595 3 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		router1 {
+		led-router1 {
 			label = "bcm53xx:amber:router";
 			gpios = <&hc595 4 GPIO_ACTIVE_HIGH>;
 		};
 
-		wan {
+		led-wan {
 			label = "bcm53xx:green:wan";
 			gpios = <&hc595 5 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		wireless0 {
+		led-wireless0 {
 			label = "bcm53xx:green:wireless";
 			gpios = <&hc595 6 GPIO_ACTIVE_HIGH>;
 		};
 
-		wireless1 {
+		led-wireless1 {
 			label = "bcm53xx:amber:wireless";
 			gpios = <&hc595 7 GPIO_ACTIVE_HIGH>;
 		};
@@ -96,7 +96,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm47081-luxul-xap-1410.dts b/arch/arm/boot/dts/broadcom/bcm47081-luxul-xap-1410.dts
index 68aaf0af3945..0198b5f9e4a7 100644
--- a/arch/arm/boot/dts/bcm47081-luxul-xap-1410.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47081-luxul-xap-1410.dts
@@ -8,7 +8,7 @@
 #include "bcm47081.dtsi"
 
 / {
-	compatible = "luxul,xap-1410v1", "brcm,bcm47081", "brcm,bcm4708";
+	compatible = "luxul,xap-1410-v1", "brcm,bcm47081", "brcm,bcm4708";
 	model = "Luxul XAP-1410 V1";
 
 	chosen {
@@ -20,22 +20,30 @@
 		reg = <0x00000000 0x08000000>;
 	};
 
+	nvram@1eff0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 
-		5ghz {
+		led-5ghz {
 			label = "bcm53xx:blue:5ghz";
 			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
 		};
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:blue:2ghz";
 			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
 		};
 
-		status {
+		led-status {
 			label = "bcm53xx:green:status";
 			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "timer";
@@ -45,7 +53,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
@@ -53,6 +61,11 @@
 	};
 };
 
+&gmac0 {
+	nvmem-cells = <&et0macaddr>;
+	nvmem-cell-names = "mac-address";
+};
+
 &spi_nor {
 	status = "okay";
 };
@@ -62,14 +75,19 @@
 
 	ports {
 		port@4 {
-			reg = <4>;
 			label = "poe";
 		};
 
 		port@5 {
-			reg = <5>;
 			label = "cpu";
-			ethernet = <&gmac0>;
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts b/arch/arm/boot/dts/broadcom/bcm47081-luxul-xwr-1200.dts
index 9316a36434f7..73ff1694a4a0 100644
--- a/arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47081-luxul-xwr-1200.dts
@@ -9,7 +9,7 @@
 #include "bcm5301x-nand-cs0-bch4.dtsi"
 
 / {
-	compatible = "luxul,xwr-1200v1", "brcm,bcm47081", "brcm,bcm4708";
+	compatible = "luxul,xwr-1200-v1", "brcm,bcm47081", "brcm,bcm4708";
 	model = "Luxul XWR-1200 V1";
 
 	chosen {
@@ -24,67 +24,71 @@
 	nvram@1eff0000 {
 		compatible = "brcm,nvram";
 		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+			#nvmem-cell-cells = <1>;
+		};
 	};
 
 	leds {
 		compatible = "gpio-leds";
 
-		power {
+		led-power {
 			label = "bcm53xx:green:power";
 			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		lan3 {
+		led-lan3 {
 			label = "bcm53xx:green:lan3";
 			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
 		};
 
-		lan4 {
+		led-lan4 {
 			label = "bcm53xx:green:lan4";
 			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
 		};
 
-		wan {
+		led-wan {
 			label = "bcm53xx:green:wan";
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
 		};
 
-		lan2 {
+		led-lan2 {
 			label = "bcm53xx:green:lan2";
 			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
 		};
 
-		usb {
+		led-usb {
 			label = "bcm53xx:green:usb";
 			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
 			trigger-sources = <&ohci_port2>, <&ehci_port2>;
 			linux,default-trigger = "usbport";
 		};
 
-		status {
+		led-status {
 			label = "bcm53xx:green:status";
 			gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "timer";
 		};
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:green:2ghz";
 			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
 		};
 
-		5ghz {
+		led-5ghz {
 			label = "bcm53xx:green:5ghz";
 			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
 		};
 
-		lan1 {
+		led-lan1 {
 			label = "bcm53xx:green:lan1";
 			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
@@ -94,7 +98,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
@@ -106,6 +110,11 @@
 	vcc-gpio = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
 };
 
+&gmac0 {
+	nvmem-cells = <&et0macaddr 0>;
+	nvmem-cell-names = "mac-address";
+};
+
 &spi_nor {
 	status = "okay";
 };
@@ -115,34 +124,37 @@
 
 	ports {
 		port@0 {
-			reg = <0>;
 			label = "lan4";
 		};
 
 		port@1 {
-			reg = <1>;
 			label = "lan3";
 		};
 
 		port@2 {
-			reg = <2>;
 			label = "lan2";
 		};
 
 		port@3 {
-			reg = <3>;
 			label = "lan1";
 		};
 
 		port@4 {
-			reg = <4>;
 			label = "wan";
+			nvmem-cells = <&et0macaddr 5>;
+			nvmem-cell-names = "mac-address";
 		};
 
 		port@5 {
-			reg = <5>;
 			label = "cpu";
-			ethernet = <&gmac0>;
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts b/arch/arm/boot/dts/broadcom/bcm47081-tplink-archer-c5-v2.dts
index 12e34a0439b4..b6a5886698b2 100644
--- a/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47081-tplink-archer-c5-v2.dts
@@ -23,50 +23,50 @@
 	leds {
 		compatible = "gpio-leds";
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:green:2ghz";
 			gpios = <&chipcommon 0 GPIO_ACTIVE_HIGH>;
 		};
 
-		lan {
+		led-lan {
 			label = "bcm53xx:green:lan";
 			gpios = <&chipcommon 1 GPIO_ACTIVE_HIGH>;
 		};
 
-		usb2-port1 {
+		led-usb2-port1 {
 			label = "bcm53xx:green:usb2-port1";
 			gpios = <&chipcommon 2 GPIO_ACTIVE_HIGH>;
 			trigger-sources = <&ohci_port1>, <&ehci_port1>;
 			linux,default-trigger = "usbport";
 		};
 
-		power {
+		led-power {
 			label = "bcm53xx:green:power";
 			gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		wan-green {
+		led-wan-green {
 			label = "bcm53xx:green:wan";
 			gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
 		};
 
-		wps {
+		led-wps {
 			label = "bcm53xx:green:wps";
 			gpios = <&chipcommon 6 GPIO_ACTIVE_HIGH>;
 		};
 
-		wan-amber {
+		led-wan-amber {
 			label = "bcm53xx:amber:wan";
 			gpios = <&chipcommon 8 GPIO_ACTIVE_HIGH>;
 		};
 
-		5ghz {
+		led-5ghz {
 			label = "bcm53xx:green:5ghz";
 			gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
 		};
 
-		usb2-port2 {
+		led-usb2-port2 {
 			label = "bcm53xx:green:usb2-port2";
 			gpios = <&chipcommon 13 GPIO_ACTIVE_HIGH>;
 			trigger-sources = <&ohci_port2>, <&ehci_port2>;
@@ -77,13 +77,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
@@ -95,30 +95,15 @@
 	status = "okay";
 
 	partitions {
-		compatible = "fixed-partitions";
-		#address-cells = <1>;
-		#size-cells = <1>;
-
-		boot@0 {
-			label = "boot";
-			reg = <0x000000 0x040000>;
-			read-only;
-		};
+		compatible = "tplink,safeloader-partitions";
+		partitions-table-offset = <0xe50000>;
 
-		os-image@100000 {
-			label = "os-image";
-			reg = <0x040000 0x200000>;
+		partition-os-image {
 			compatible = "brcm,trx";
 		};
 
-		rootfs@240000 {
-			label = "rootfs";
-			reg = <0x240000 0xc00000>;
-		};
-
-		nvram@ff0000 {
-			label = "nvram";
-			reg = <0xff0000 0x010000>;
+		partition-file-system {
+			linux,rootfs;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/bcm47081.dtsi b/arch/arm/boot/dts/broadcom/bcm47081.dtsi
index ed13af028528..ed13af028528 100644
--- a/arch/arm/boot/dts/bcm47081.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm47081.dtsi
diff --git a/arch/arm/boot/dts/broadcom/bcm4709-asus-rt-ac3200.dts b/arch/arm/boot/dts/broadcom/bcm4709-asus-rt-ac3200.dts
new file mode 100644
index 000000000000..3da2daee0c84
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm4709-asus-rt-ac3200.dts
@@ -0,0 +1,150 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Author: Tom Brautaset <tbrautaset@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4709.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+#include <dt-bindings/leds/common.h>
+
+/ {
+	compatible = "asus,rt-ac3200", "brcm,bcm4709", "brcm,bcm4708";
+	model = "ASUS RT-AC3200";
+
+	memory@0 {
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+		device_type = "memory";
+	};
+
+	nvram@1c080000 {
+		compatible = "brcm,nvram";
+		reg = <0x1c080000 0x00180000>;
+
+		et0macaddr: et0macaddr {
+			#nvmem-cell-cells = <1>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-reset {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+
+		button-wifi {
+			label = "Wi-Fi";
+			linux,code = <KEY_RFKILL>;
+			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
+		};
+
+		button-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power {
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-wan-red {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_WAN;
+			gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wps {
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_WPS;
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&gmac0 {
+	nvmem-cells = <&et0macaddr 0>;
+	nvmem-cell-names = "mac-address";
+};
+
+&gmac1 {
+	nvmem-cells = <&et0macaddr 1>;
+	nvmem-cell-names = "mac-address";
+};
+
+&gmac2 {
+	nvmem-cells = <&et0macaddr 2>;
+	nvmem-cell-names = "mac-address";
+};
+
+&nandcs {
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			reg = <0x00000000 0x00080000>;
+			label = "boot";
+			read-only;
+		};
+
+		partition@80000 {
+			reg = <0x00080000 0x00180000>;
+			label = "nvram";
+		};
+
+		partition@200000 {
+			compatible = "brcm,trx";
+			reg = <0x00200000 0x07e00000>;
+			label = "firmware";
+		};
+	};
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "wan";
+		};
+
+		port@1 {
+			label = "lan4";
+		};
+
+		port@2 {
+			label = "lan3";
+		};
+
+		port@3 {
+			label = "lan2";
+		};
+
+		port@4 {
+			label = "lan1";
+		};
+	};
+};
+
+&usb2 {
+	vcc-gpio = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3_phy {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts b/arch/arm/boot/dts/broadcom/bcm4709-asus-rt-ac87u.dts
index 7546c8d07bcd..59400217f8c3 100644
--- a/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4709-asus-rt-ac87u.dts
@@ -25,21 +25,27 @@
 		      <0x88000000 0x08000000>;
 	};
 
+	nvram@1c080000 {
+		et1macaddr: et1macaddr {
+			#nvmem-cell-cells = <1>;
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 
-		wps {
+		led-wps {
 			label = "bcm53xx:blue:wps";
 			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
 		};
 
-		power {
+		led-power {
 			label = "bcm53xx:blue:power";
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		wan {
+		led-wan {
 			label = "bcm53xx:red:wan";
 			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
 		};
@@ -47,16 +53,14 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
@@ -64,6 +68,11 @@
 	};
 };
 
+&gmac0 {
+	nvmem-cells = <&et1macaddr 0>;
+	nvmem-cell-names = "mac-address";
+};
+
 &usb3_phy {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts b/arch/arm/boot/dts/broadcom/bcm4709-buffalo-wxr-1900dhp.dts
index beae9eab9cb8..b7cd2faa30ce 100644
--- a/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4709-buffalo-wxr-1900dhp.dts
@@ -28,48 +28,48 @@
 	leds {
 		compatible = "gpio-leds";
 
-		usb {
+		led-usb {
 			label = "bcm53xx:green:usb";
 			gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>;
 		};
 
-		power-amber {
+		led-power-amber {
 			label = "bcm53xx:amber:power";
 			gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
 		};
 
-		power-white {
+		led-power-white {
 			label = "bcm53xx:white:power";
 			gpios = <&chipcommon 6 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		router-amber {
+		led-router-amber {
 			label = "bcm53xx:amber:router";
 			gpios = <&chipcommon 7 GPIO_ACTIVE_HIGH>;
 		};
 
-		router-white {
+		led-router-white {
 			label = "bcm53xx:white:router";
 			gpios = <&chipcommon 8 GPIO_ACTIVE_HIGH>;
 		};
 
-		wan-amber {
+		led-wan-amber {
 			label = "bcm53xx:amber:wan";
 			gpios = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
 		};
 
-		wan-white {
+		led-wan-white {
 			label = "bcm53xx:white:wan";
 			gpios = <&chipcommon 10 GPIO_ACTIVE_HIGH>;
 		};
 
-		wireless-amber {
+		led-wireless-amber {
 			label = "bcm53xx:amber:wireless";
 			gpios = <&chipcommon 11 GPIO_ACTIVE_HIGH>;
 		};
 
-		wireless-white {
+		led-wireless-white {
 			label = "bcm53xx:white:wireless";
 			gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
 		};
@@ -77,42 +77,40 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		power {
+		button-power {
 			label = "Power";
 			linux,code = <KEY_POWER>;
 			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
 		};
 
-		aoss {
+		button-aoss {
 			label = "AOSS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 16 GPIO_ACTIVE_LOW>;
 		};
 
 		/* Commit mode set by switch? */
-		mode {
+		button-mode {
 			label = "Mode";
 			linux,code = <KEY_SETUP>;
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
 		};
 
 		/* Switch: AP mode */
-		sw_ap {
+		button-sw-ap {
 			label = "AP";
 			linux,code = <BTN_0>;
 			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
 		};
 
-		eject {
+		button-eject {
 			label = "USB eject";
 			linux,code = <KEY_EJECTCD>;
 			gpios = <&chipcommon 20 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4709-linksys-ea9200.dts b/arch/arm/boot/dts/broadcom/bcm4709-linksys-ea9200.dts
index 7879f7d7d9c3..2ba5adf2b7e7 100644
--- a/arch/arm/boot/dts/bcm4709-linksys-ea9200.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4709-linksys-ea9200.dts
@@ -29,16 +29,14 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
@@ -49,3 +47,41 @@
 &usb3_phy {
 	status = "okay";
 };
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan1";
+		};
+
+		port@1 {
+			label = "lan2";
+		};
+
+		port@2 {
+			label = "lan3";
+		};
+
+		port@3 {
+			label = "lan4";
+		};
+
+		port@4 {
+			label = "wan";
+		};
+
+		port@5 {
+			status = "disabled";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			label = "cpu";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm4709-netgear-r7000.dts b/arch/arm/boot/dts/broadcom/bcm4709-netgear-r7000.dts
index 56d309dbc6b0..24ba8f8f9bf3 100644
--- a/arch/arm/boot/dts/bcm4709-netgear-r7000.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4709-netgear-r7000.dts
@@ -28,43 +28,43 @@
 	leds {
 		compatible = "gpio-leds";
 
-		power-white {
+		led-power-white {
 			label = "bcm53xx:white:power";
 			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		power-amber {
+		led-power-amber {
 			label = "bcm53xx:amber:power";
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 		};
 
-		5ghz {
+		led-5ghz {
 			label = "bcm53xx:white:5ghz";
 			gpios = <&chipcommon 12 GPIO_ACTIVE_LOW>;
 		};
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:white:2ghz";
 			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		led-wps {
 			label = "bcm53xx:white:wps";
 			gpios = <&chipcommon 14 GPIO_ACTIVE_HIGH>;
 		};
 
-		wireless {
+		led-wireless {
 			label = "bcm53xx:white:wireless";
 			gpios = <&chipcommon 15 GPIO_ACTIVE_HIGH>;
 		};
 
-		usb3 {
+		led-usb3 {
 			label = "bcm53xx:white:usb3";
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
 		};
 
-		usb2 {
+		led-usb2 {
 			label = "bcm53xx:white:usb2";
 			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
 		};
@@ -72,22 +72,20 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
 		};
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4709-netgear-r8000.dts b/arch/arm/boot/dts/broadcom/bcm4709-netgear-r8000.dts
index 89f992af61d1..127ca8741220 100644
--- a/arch/arm/boot/dts/bcm4709-netgear-r8000.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4709-netgear-r8000.dts
@@ -39,59 +39,59 @@
 	leds {
 		compatible = "gpio-leds";
 
-		power-white {
+		led-power-white {
 			label = "bcm53xx:white:power";
 			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		power-amber {
+		led-power-amber {
 			label = "bcm53xx:amber:power";
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 		};
 
-		wan-white {
+		led-wan-white {
 			label = "bcm53xx:white:wan";
 			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		wan-amber {
+		led-wan-amber {
 			label = "bcm53xx:amber:wan";
 			gpios = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
 		};
 
-		5ghz-1 {
+		led-5ghz-1 {
 			label = "bcm53xx:white:5ghz-1";
 			gpios = <&chipcommon 12 GPIO_ACTIVE_LOW>;
 		};
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:white:2ghz";
 			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
 		};
 
-		wireless {
+		led-wireless {
 			label = "bcm53xx:white:wireless";
 			gpios = <&chipcommon 14 GPIO_ACTIVE_HIGH>;
 		};
 
-		wps {
+		led-wps {
 			label = "bcm53xx:white:wps";
 			gpios = <&chipcommon 15 GPIO_ACTIVE_HIGH>;
 		};
 
-		5ghz-2 {
+		led-5ghz-2 {
 			label = "bcm53xx:white:5ghz-2";
 			gpios = <&chipcommon 16 GPIO_ACTIVE_LOW>;
 		};
 
-		usb3 {
+		led-usb3 {
 			label = "bcm53xx:white:usb3";
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
 		};
 
-		usb2 {
+		led-usb2 {
 			label = "bcm53xx:white:usb2";
 			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
 		};
@@ -99,28 +99,26 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
 		};
 
-		brightness {
+		button-brightness {
 			label = "Backlight";
 			linux,code = <KEY_BRIGHTNESS_ZERO>;
 			gpios = <&chipcommon 19 GPIO_ACTIVE_LOW>;
@@ -139,8 +137,10 @@
 		#size-cells = <2>;
 
 		wifi@0,1,0 {
+			compatible = "brcm,bcm4366-fmac", "brcm,bcm4329-fmac";
 			reg = <0x0000 0 0 0 0>;
 			ieee80211-freq-limit = <5735000 5835000>;
+			brcm,ccode-map = "JP-JP-78", "US-Q2-86";
 		};
 	};
 };
@@ -161,6 +161,19 @@
 			#address-cells = <3>;
 			#size-cells = <2>;
 
+			bridge@1,0 {
+				reg = <0x800 0 0 0 0>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+
+				wifi@0,0 {
+					compatible = "brcm,bcm4366-fmac", "brcm,bcm4329-fmac";
+					reg = <0x0000 0 0 0 0>;
+					brcm,ccode-map = "JP-JP-78", "US-Q2-86";
+				};
+			};
+
 			bridge@1,2,2 {
 				reg = <0x1000 0 0 0 0>;
 
@@ -168,8 +181,10 @@
 				#size-cells = <2>;
 
 				wifi@1,4,0 {
+					compatible = "brcm,bcm4366-fmac", "brcm,bcm4329-fmac";
 					reg = <0x0000 0 0 0 0>;
 					ieee80211-freq-limit = <5170000 5730000>;
+					brcm,ccode-map = "JP-JP-78", "US-Q2-86";
 				};
 			};
 		};
@@ -193,39 +208,45 @@
 
 	ports {
 		port@0 {
-			reg = <0>;
 			label = "lan1";
 		};
 
 		port@1 {
-			reg = <1>;
 			label = "lan2";
 		};
 
 		port@2 {
-			reg = <2>;
 			label = "lan3";
 		};
 
 		port@3 {
-			reg = <3>;
 			label = "lan4";
 		};
 
 		port@4 {
-			reg = <4>;
 			label = "wan";
 		};
 
-		port@8 {
-			reg = <8>;
-			label = "cpu";
-			ethernet = <&gmac2>;
+		port@5 {
+			status = "disabled";
 
 			fixed-link {
 				speed = <1000>;
 				full-duplex;
 			};
 		};
+
+		port@7 {
+			status = "disabled";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		port@8 {
+			label = "cpu";
+		};
 	};
 };
diff --git a/arch/arm/boot/dts/bcm4709-tplink-archer-c9-v1.dts b/arch/arm/boot/dts/broadcom/bcm4709-tplink-archer-c9-v1.dts
index c2a266a439d0..5a8b2b1567e6 100644
--- a/arch/arm/boot/dts/bcm4709-tplink-archer-c9-v1.dts
+++ b/arch/arm/boot/dts/broadcom/bcm4709-tplink-archer-c9-v1.dts
@@ -23,27 +23,27 @@
 	leds {
 		compatible = "gpio-leds";
 
-		lan {
+		led-lan {
 			label = "bcm53xx:blue:lan";
 			gpios = <&chipcommon 1 GPIO_ACTIVE_HIGH>;
 		};
 
-		wps {
+		led-wps {
 			label = "bcm53xx:blue:wps";
 			gpios = <&chipcommon 2 GPIO_ACTIVE_HIGH>;
 		};
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:blue:2ghz";
 			gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>;
 		};
 
-		5ghz {
+		led-5ghz {
 			label = "bcm53xx:blue:5ghz";
 			gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
 		};
 
-		usb3 {
+		led-usb3 {
 			label = "bcm53xx:blue:usb3";
 			gpios = <&chipcommon 6 GPIO_ACTIVE_HIGH>;
 			trigger-sources = <&ohci_port1>, <&ehci_port1>,
@@ -51,24 +51,24 @@
 			linux,default-trigger = "usbport";
 		};
 
-		usb2 {
+		led-usb2 {
 			label = "bcm53xx:blue:usb2";
 			gpios = <&chipcommon 7 GPIO_ACTIVE_HIGH>;
 			trigger-sources = <&ohci_port2>, <&ehci_port2>;
 			linux,default-trigger = "usbport";
 		};
 
-		wan-blue {
+		led-wan-blue {
 			label = "bcm53xx:blue:wan";
 			gpios = <&chipcommon 14 GPIO_ACTIVE_HIGH>;
 		};
 
-		wan-amber {
+		led-wan-amber {
 			label = "bcm53xx:amber:wan";
 			gpios = <&chipcommon 15 GPIO_ACTIVE_HIGH>;
 		};
 
-		power {
+		led-power {
 			label = "bcm53xx:blue:power";
 			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
@@ -77,16 +77,14 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
@@ -106,30 +104,15 @@
 	status = "okay";
 
 	partitions {
-		compatible = "fixed-partitions";
-		#address-cells = <1>;
-		#size-cells = <1>;
-
-		boot@0 {
-			label = "boot";
-			reg = <0x000000 0x040000>;
-			read-only;
-		};
+		compatible = "tplink,safeloader-partitions";
+		partitions-table-offset = <0xe50000>;
 
-		os-image@100000 {
-			label = "os-image";
-			reg = <0x040000 0x200000>;
+		partition-os-image {
 			compatible = "brcm,trx";
 		};
 
-		rootfs@240000 {
-			label = "rootfs";
-			reg = <0x240000 0xc00000>;
-		};
-
-		nvram@ff0000 {
-			label = "nvram";
-			reg = <0xff0000 0x010000>;
+		partition-file-system {
+			linux,rootfs;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/bcm4709.dtsi b/arch/arm/boot/dts/broadcom/bcm4709.dtsi
index cba3d910bed8..cba3d910bed8 100644
--- a/arch/arm/boot/dts/bcm4709.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm4709.dtsi
diff --git a/arch/arm/boot/dts/broadcom/bcm47094-asus-rt-ac3100.dts b/arch/arm/boot/dts/broadcom/bcm47094-asus-rt-ac3100.dts
new file mode 100644
index 000000000000..1655ac95769c
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm47094-asus-rt-ac3100.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Author: Arınç ÜNAL <arinc.unal@arinc9.com>
+ */
+
+/dts-v1/;
+
+#include "bcm47094-asus-rt-ac3100.dtsi"
+
+/ {
+	compatible = "asus,rt-ac3100", "brcm,bcm47094", "brcm,bcm4708";
+	model = "ASUS RT-AC3100";
+
+	nvram@1c080000 {
+		et0macaddr: et0macaddr {
+			#nvmem-cell-cells = <1>;
+		};
+	};
+};
+
+&gmac0 {
+	nvmem-cells = <&et0macaddr 0>;
+	nvmem-cell-names = "mac-address";
+};
+
+&gmac1 {
+	nvmem-cells = <&et0macaddr 1>;
+	nvmem-cell-names = "mac-address";
+};
+
+&gmac2 {
+	nvmem-cells = <&et0macaddr 2>;
+	nvmem-cell-names = "mac-address";
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm47094-asus-rt-ac3100.dtsi b/arch/arm/boot/dts/broadcom/bcm47094-asus-rt-ac3100.dtsi
new file mode 100644
index 000000000000..2cfaaabc7a6a
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm47094-asus-rt-ac3100.dtsi
@@ -0,0 +1,168 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Author: Arınç ÜNAL <arinc.unal@arinc9.com>
+ */
+
+#include "bcm47094.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+#include <dt-bindings/leds/common.h>
+
+/ {
+	memory@0 {
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x18000000>;
+		device_type = "memory";
+	};
+
+	nvram@1c080000 {
+		compatible = "brcm,nvram";
+		reg = <0x1c080000 0x00180000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-led {
+			label = "Backlight";
+			linux,code = <KEY_BRIGHTNESS_ZERO>;
+			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
+		};
+
+		button-reset {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+
+		button-wifi {
+			label = "Wi-Fi";
+			linux,code = <KEY_RFKILL>;
+			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
+		};
+
+		button-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 20 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-lan {
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_LAN;
+			gpios = <&chipcommon 21 GPIO_ACTIVE_LOW>;
+		};
+
+		led-power {
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-usb2 {
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_USB;
+			function-enumerator = <1>;
+			gpios = <&chipcommon 16 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&ehci_port2>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-usb3 {
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_USB;
+			function-enumerator = <2>;
+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&ehci_port1>, <&xhci_port1>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-wan-red {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_WAN;
+			gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wps {
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_WPS;
+			gpios = <&chipcommon 19 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&nandcs {
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			reg = <0x00000000 0x00080000>;
+			label = "boot";
+			read-only;
+		};
+
+		partition@80000 {
+			reg = <0x00080000 0x00180000>;
+			label = "nvram";
+		};
+
+		partition@200000 {
+			compatible = "brcm,trx";
+			reg = <0x00200000 0x07e00000>;
+			label = "firmware";
+		};
+	};
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan4";
+		};
+
+		port@1 {
+			label = "lan3";
+		};
+
+		port@2 {
+			label = "lan2";
+		};
+
+		port@3 {
+			label = "lan1";
+		};
+
+		port@4 {
+			label = "wan";
+		};
+
+		port@5 {
+			label = "cpu";
+		};
+
+		port@7 {
+			label = "cpu";
+		};
+
+		port@8 {
+			label = "cpu";
+		};
+	};
+};
+
+&usb2 {
+	vcc-gpio = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3_phy {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm47094-asus-rt-ac5300.dts b/arch/arm/boot/dts/broadcom/bcm47094-asus-rt-ac5300.dts
new file mode 100644
index 000000000000..01ec8c03686a
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm47094-asus-rt-ac5300.dts
@@ -0,0 +1,156 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Author: Tom Brautaset <tbrautaset@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm47094.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+#include <dt-bindings/leds/common.h>
+
+/ {
+	compatible = "asus,rt-ac5300", "brcm,bcm47094", "brcm,bcm4708";
+	model = "ASUS RT-AC5300";
+
+	memory@0 {
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x18000000>;
+		device_type = "memory";
+	};
+
+	nvram@1c080000 {
+		compatible = "brcm,nvram";
+		reg = <0x1c080000 0x00180000>;
+
+		et1macaddr: et1macaddr {
+			#nvmem-cell-cells = <1>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-reset {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+
+		button-wifi {
+			label = "Wi-Fi";
+			linux,code = <KEY_RFKILL>;
+			gpios = <&chipcommon 20 GPIO_ACTIVE_LOW>;
+		};
+
+		button-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-lan {
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_LAN;
+			gpios = <&chipcommon 21 GPIO_ACTIVE_LOW>;
+		};
+
+		led-power {
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-wan-red {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_WAN;
+			gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-wps {
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_WPS;
+			gpios = <&chipcommon 19 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&gmac0 {
+	nvmem-cells = <&et1macaddr 0>;
+	nvmem-cell-names = "mac-address";
+};
+
+&gmac1 {
+	nvmem-cells = <&et1macaddr 1>;
+	nvmem-cell-names = "mac-address";
+};
+
+&gmac2 {
+	nvmem-cells = <&et1macaddr 2>;
+	nvmem-cell-names = "mac-address";
+};
+
+&nandcs {
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			reg = <0x00000000 0x00080000>;
+			label = "boot";
+			read-only;
+		};
+
+		partition@80000 {
+			reg = <0x00080000 0x00180000>;
+			label = "nvram";
+		};
+
+		partition@200000 {
+			compatible = "brcm,trx";
+			reg = <0x00200000 0x07e00000>;
+			label = "firmware";
+		};
+	};
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "wan";
+		};
+
+		port@1 {
+			label = "lan1";
+		};
+
+		port@2 {
+			label = "lan2";
+		};
+
+		port@3 {
+			label = "lan3";
+		};
+
+		port@4 {
+			label = "lan4";
+		};
+	};
+};
+
+&usb2 {
+	vcc-gpio = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3_phy {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm47094-asus-rt-ac88u.dts b/arch/arm/boot/dts/broadcom/bcm47094-asus-rt-ac88u.dts
new file mode 100644
index 000000000000..a197f447fd97
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm47094-asus-rt-ac88u.dts
@@ -0,0 +1,127 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Author: Arınç ÜNAL <arinc.unal@arinc9.com>
+ */
+
+/dts-v1/;
+
+#include "bcm47094-asus-rt-ac3100.dtsi"
+
+/ {
+	compatible = "asus,rt-ac88u", "brcm,bcm47094", "brcm,bcm4708";
+	model = "ASUS RT-AC88U";
+
+	nvram@1c080000 {
+		et1macaddr: et1macaddr {
+			#nvmem-cell-cells = <1>;
+		};
+	};
+
+	switch {
+		compatible = "realtek,rtl8365mb";
+		mdc-gpios = <&chipcommon 6 GPIO_ACTIVE_HIGH>;
+		mdio-gpios = <&chipcommon 7 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
+		realtek,disable-leds;
+		dsa,member = <1 0>;
+
+		mdio {
+			compatible = "realtek,smi-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ethphy0: ethernet-phy@0 {
+				reg = <0>;
+			};
+
+			ethphy1: ethernet-phy@1 {
+				reg = <1>;
+			};
+
+			ethphy2: ethernet-phy@2 {
+				reg = <2>;
+			};
+
+			ethphy3: ethernet-phy@3 {
+				reg = <3>;
+			};
+		};
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				label = "lan5";
+				phy-handle = <&ethphy0>;
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "lan6";
+				phy-handle = <&ethphy1>;
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "lan7";
+				phy-handle = <&ethphy2>;
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "lan8";
+				phy-handle = <&ethphy3>;
+			};
+
+			port@6 {
+				reg = <6>;
+				label = "cpu";
+				ethernet = <&sw0_p5>;
+				phy-mode = "rgmii";
+				tx-internal-delay-ps = <2000>;
+				rx-internal-delay-ps = <2100>;
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+					pause;
+				};
+			};
+		};
+	};
+};
+
+&gmac0 {
+	status = "disabled";
+};
+
+&gmac1 {
+	nvmem-cells = <&et1macaddr 0>;
+	nvmem-cell-names = "mac-address";
+};
+
+&gmac2 {
+	nvmem-cells = <&et1macaddr 1>;
+	nvmem-cell-names = "mac-address";
+};
+
+&srab {
+	dsa,member = <0 0>;
+
+	ports {
+		sw0_p5: port@5 {
+			/delete-property/ethernet;
+
+			label = "extsw";
+			phy-mode = "rgmii";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+				pause;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts b/arch/arm/boot/dts/broadcom/bcm47094-dlink-dir-885l.dts
index 60bfd52ee677..c5099defe9f9 100644
--- a/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47094-dlink-dir-885l.dts
@@ -25,6 +25,15 @@
 		      <0x88000000 0x08000000>;
 	};
 
+	nvram@1e3f0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1e3f0000 0x10000>;
+
+		et2macaddr: et2macaddr {
+			#nvmem-cell-cells = <1>;
+		};
+	};
+
 	nand_controller: nand-controller@18028000 {
 		nand@0 {
 			partitions {
@@ -33,6 +42,7 @@
 				#size-cells = <1>;
 
 				partition@0 {
+					compatible = "seama";
 					label = "firmware";
 					reg = <0x00000000 0x08000000>;
 				};
@@ -43,28 +53,28 @@
 	leds {
 		compatible = "gpio-leds";
 
-		power-white {
+		led-power-white {
 			label = "bcm53xx:white:power";
 			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		wan-white {
+		led-wan-white {
 			label = "bcm53xx:white:wan";
 			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
 		};
 
-		power-amber {
+		led-power-amber {
 			label = "bcm53xx:amber:power";
 			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
 		};
 
-		wan-amber {
+		led-wan-amber {
 			label = "bcm53xx:amber:wan";
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 		};
 
-		usb3-white {
+		led-usb3-white {
 			label = "bcm53xx:white:usb3";
 			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
 			trigger-sources = <&ohci_port1>, <&ehci_port1>,
@@ -72,12 +82,12 @@
 			linux,default-trigger = "usbport";
 		};
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:white:2ghz";
 			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
 		};
 
-		5ghz {
+		led-5ghz {
 			label = "bcm53xx:white:5ghz";
 			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
 		};
@@ -86,20 +96,20 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
 		};
 
 		/* Switch: router / extender */
-		extender {
+		button-extender {
 			label = "Extender";
 			linux,code = <BTN_0>;
 			gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
@@ -111,6 +121,11 @@
 	vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
 };
 
+&gmac0 {
+	nvmem-cells = <&et2macaddr 0>;
+	nvmem-cell-names = "mac-address";
+};
+
 &spi_nor {
 	status = "okay";
 };
@@ -124,39 +139,37 @@
 
 	ports {
 		port@0 {
-			reg = <0>;
 			label = "lan4";
 		};
 
 		port@1 {
-			reg = <1>;
 			label = "lan3";
 		};
 
 		port@2 {
-			reg = <2>;
 			label = "lan2";
 		};
 
 		port@3 {
-			reg = <3>;
 			label = "lan1";
 		};
 
 		port@4 {
-			reg = <4>;
 			label = "wan";
+			nvmem-cells = <&et2macaddr 3>;
+			nvmem-cell-names = "mac-address";
+		};
+
+		port@5 {
+			status = "disabled";
+		};
+
+		port@7 {
+			status = "disabled";
 		};
 
 		port@8 {
-			reg = <8>;
 			label = "cpu";
-			ethernet = <&gmac2>;
-
-			fixed-link {
-				speed = <1000>;
-				full-duplex;
-			};
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/broadcom/bcm47094-dlink-dir-890l.dts b/arch/arm/boot/dts/broadcom/bcm47094-dlink-dir-890l.dts
new file mode 100644
index 000000000000..3124dfd01b94
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm47094-dlink-dir-890l.dts
@@ -0,0 +1,208 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device tree for D-Link DIR-890L
+ * D-Link calls this board "WRGAC36"
+ * this router has the same looks and form factor as D-Link DIR-885L.
+ *
+ * Some differences from DIR-885L include a separate USB2 port, separate LEDs
+ * for USB2 and USB3, a separate VCC supply for the USB2 slot and no
+ * router/extender switch is mounted (there is an empty mount point on the
+ * PCB) so this device is a pure router. Also the LAN ports are in the right
+ * order.
+ *
+ * Based on the device tree for DIR-885L
+ * Copyright (C) 2016 Rafał Miłecki <zajec5@gmail.com>
+ * Copyright (C) 2022 Linus Walleij
+ */
+
+/dts-v1/;
+
+#include "bcm47094.dtsi"
+#include "bcm5301x-nand-cs0-bch1.dtsi"
+
+/ {
+	compatible = "dlink,dir-890l", "brcm,bcm47094", "brcm,bcm4708";
+	model = "D-Link DIR-890L";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlycon";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+	leds {
+		/*
+		 * LED information is derived from the boot log which
+		 * conveniently lists all the LEDs.
+		 */
+		compatible = "gpio-leds";
+
+		led-power-white {
+			label = "bcm53xx:white:power";
+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-wan-white {
+			label = "bcm53xx:white:wan";
+			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
+		};
+
+		led-power-amber {
+			label = "bcm53xx:amber:power";
+			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
+		};
+
+		led-wan-amber {
+			label = "bcm53xx:amber:wan";
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+		};
+
+		led-usb3-white {
+			label = "bcm53xx:white:usb3";
+			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&xhci_port1>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-usb2-white {
+			label = "bcm53xx:white:usb2";
+			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
+			trigger-sources = <&ohci_port1>, <&ehci_port1>;
+			linux,default-trigger = "usbport";
+		};
+
+		led-2ghz {
+			label = "bcm53xx:white:2ghz";
+			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
+		};
+
+		led-5ghz {
+			label = "bcm53xx:white:5ghz";
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
+		};
+
+		/* Called "factory reset" in the vendor dmesg */
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	/*
+	 * The flash memory is memory mapped at 0x1e000000-0x1fffffff
+	 * 64KB blocks; total size 2MB, same that can be
+	 * found attached to the spi_nor SPI controller.
+	 */
+	nvram@1e1f0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1e1f0000 0x00010000>;
+
+		et0macaddr: et0macaddr {
+		};
+	};
+};
+
+&gmac2 {
+	/*
+	 * The NVRAM curiously does not contain a MAC address
+	 * for et2 so since that is the only ethernet interface
+	 * actually in use on the platform, we use this et0 MAC
+	 * address for et2.
+	 */
+	nvmem-cells = <&et0macaddr>;
+	nvmem-cell-names = "mac-address";
+};
+
+&spi_nor {
+	status = "okay";
+};
+
+&nandcs {
+	/* Spansion S34ML01G2, 128MB with 128KB erase blocks */
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/*
+		 * This is called "nflash" in the vendor kernel with
+		 * "upgrade" and "rootfs" (probably using OpenWrt
+		 * splitpart). We call it "firmware" like standard tools
+		 * assume. The CFE loader contains incorrect information
+		 * about TRX partitions, ignore this, there are no TRX
+		 * partitions: this device uses SEAMA.
+		 */
+		firmware@0 {
+			compatible = "seama";
+			label = "firmware";
+			reg = <0x00000000 0x08000000>;
+		};
+	};
+};
+
+&usb2 {
+	vcc-gpios = <&chipcommon 21 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3 {
+	vcc-gpios = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "lan1";
+		};
+
+		port@1 {
+			label = "lan2";
+		};
+
+		port@2 {
+			label = "lan3";
+		};
+
+		port@3 {
+			label = "lan4";
+		};
+
+		port@4 {
+			label = "wan";
+		};
+
+		port@5 {
+			status = "disabled";
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			label = "cpu";
+			phy-mode = "rgmii";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm47094-linksys-panamera.dts b/arch/arm/boot/dts/broadcom/bcm47094-linksys-panamera.dts
index 9bef6b9bfa8d..2b5c80d835e9 100644
--- a/arch/arm/boot/dts/bcm47094-linksys-panamera.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47094-linksys-panamera.dts
@@ -30,19 +30,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 		};
 
-		rfkill {
+		button-rfkill {
 				label = "WiFi";
 				linux,code = <KEY_RFKILL>;
 				gpios = <&chipcommon 16 GPIO_ACTIVE_LOW>;
 		};
 
-		reset {
+		button-reset {
 				label = "Reset";
 				linux,code = <KEY_RESTART>;
 				gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
@@ -52,19 +52,19 @@
 	leds {
 		compatible = "gpio-leds";
 
-		wps {
+		led-wps {
 			label = "bcm53xx:white:wps";
 			gpios = <&chipcommon 22 GPIO_ACTIVE_LOW>;
 		};
 
-		usb2 {
+		led-usb2 {
 			label = "bcm53xx:green:usb2";
 			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
 			trigger-sources = <&ohci_port2>, <&ehci_port2>;
 			linux,default-trigger = "usbport";
 		};
 
-		usb3 {
+		led-usb3 {
 			label = "bcm53xx:green:usb3";
 			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
 			trigger-sources = <&ohci_port1>, <&ehci_port1>,
@@ -72,58 +72,58 @@
 			linux,default-trigger = "usbport";
 		};
 
-		power {
+		led-power {
 			label = "bcm53xx:white:power";
 			gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
 		};
 
-		wifi-disabled {
+		led-wifi-disabled {
 			label = "bcm53xx:amber:wifi-disabled";
 			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
 		};
 
-		wifi-enabled {
+		led-wifi-enabled {
 			label = "bcm53xx:white:wifi-enabled";
 			gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
 		};
 
-		bluebar1 {
+		led-bluebar1 {
 			label = "bcm53xx:white:bluebar1";
 			gpios = <&chipcommon 11 GPIO_ACTIVE_HIGH>;
 		};
 
-		bluebar2 {
+		led-bluebar2 {
 			label = "bcm53xx:white:bluebar2";
 			gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
 		};
 
-		bluebar3 {
+		led-bluebar3 {
 			label = "bcm53xx:white:bluebar3";
 			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
 		};
 
-		bluebar4 {
+		led-bluebar4 {
 			label = "bcm53xx:white:bluebar4";
 			gpios = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
 		};
 
-		bluebar5 {
+		led-bluebar5 {
 			label = "bcm53xx:white:bluebar5";
 			gpios = <&chipcommon 19 GPIO_ACTIVE_HIGH>;
 		};
 
-		bluebar6 {
+		led-bluebar6 {
 			label = "bcm53xx:white:bluebar6";
 			gpios = <&chipcommon 20 GPIO_ACTIVE_HIGH>;
 		};
 
-		bluebar7 {
+		led-bluebar7 {
 			label = "bcm53xx:white:bluebar7";
 			gpios = <&chipcommon 21 GPIO_ACTIVE_HIGH>;
 		};
 
-		bluebar8 {
+		led-bluebar8 {
 			label = "bcm53xx:white:bluebar8";
 			gpios = <&chipcommon 8 GPIO_ACTIVE_HIGH>;
 		};
@@ -207,29 +207,32 @@
 	dsa,member = <0 0>;
 
 	ports {
+		sw0_p0: port@0 {
+			label = "extsw";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
 		port@1 {
-			reg = <1>;
 			label = "lan7";
 		};
 
 		port@2 {
-			reg = <2>;
 			label = "lan4";
 		};
 
 		port@3 {
-			reg = <3>;
 			label = "lan8";
 		};
 
 		port@4 {
-			reg = <4>;
 			label = "wan";
 		};
 
 		port@5 {
-			reg = <5>;
-			ethernet = <&gmac0>;
 			label = "cpu";
 			status = "disabled";
 
@@ -240,8 +243,6 @@
 		};
 
 		port@7 {
-			reg = <7>;
-			ethernet = <&gmac1>;
 			label = "cpu";
 			status = "disabled";
 
@@ -252,24 +253,7 @@
 		};
 
 		port@8 {
-			reg = <8>;
-			ethernet = <&gmac2>;
 			label = "cpu";
-
-			fixed-link {
-				speed = <1000>;
-				full-duplex;
-			};
-		};
-
-		sw0_p0: port@0 {
-			reg = <0>;
-			label = "extsw";
-
-			fixed-link {
-				speed = <1000>;
-				full-duplex;
-			};
 		};
 	};
 };
@@ -295,7 +279,7 @@
 			reg = <0x080000 0x0100000>;
 		};
 
-		partition@180000{
+		partition@180000 {
 			label = "devinfo";
 			reg = <0x0180000 0x080000>;
 		};
diff --git a/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts b/arch/arm/boot/dts/broadcom/bcm47094-luxul-abr-4500.dts
index b51a0ee7e584..e374062eb5b7 100644
--- a/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47094-luxul-abr-4500.dts
@@ -25,18 +25,22 @@
 	nvram@1eff0000 {
 		compatible = "brcm,nvram";
 		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+			#nvmem-cell-cells = <1>;
+		};
 	};
 
 	leds {
 		compatible = "gpio-leds";
 
-		status {
+		led-status {
 			label = "bcm53xx:green:status";
 			gpios = <&chipcommon 20 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "timer";
 		};
 
-		usb3 {
+		led-usb3 {
 			label = "bcm53xx:green:usb3";
 			gpios = <&chipcommon 19 GPIO_ACTIVE_LOW>;
 			trigger-sources = <&ohci_port1>, <&ehci_port1>,
@@ -49,7 +53,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
@@ -61,6 +65,11 @@
 	vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
 };
 
+&gmac0 {
+	nvmem-cells = <&et0macaddr 0>;
+	nvmem-cell-names = "mac-address";
+};
+
 &spi_nor {
 	status = "okay";
 };
@@ -74,34 +83,37 @@
 
 	ports {
 		port@0 {
-			reg = <0>;
 			label = "wan";
+			nvmem-cells = <&et0macaddr 1>;
+			nvmem-cell-names = "mac-address";
 		};
 
 		port@1 {
-			reg = <1>;
 			label = "lan4";
 		};
 
 		port@2 {
-			reg = <2>;
 			label = "lan3";
 		};
 
 		port@3 {
-			reg = <3>;
 			label = "lan2";
 		};
 
 		port@4 {
-			reg = <4>;
 			label = "lan1";
 		};
 
 		port@5 {
-			reg = <5>;
 			label = "cpu";
-			ethernet = <&gmac0>;
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/bcm47094-luxul-xap-1610.dts b/arch/arm/boot/dts/broadcom/bcm47094-luxul-xap-1610.dts
index 6fa101f0a90d..badafa024d24 100644
--- a/arch/arm/boot/dts/bcm47094-luxul-xap-1610.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47094-luxul-xap-1610.dts
@@ -20,21 +20,29 @@
 		reg = <0x00000000 0x08000000>;
 	};
 
+	nvram@1eff0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 
-		status	{
+		led-status {
 			label = "bcm53xx:green:status";
 			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "timer";
 		};
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:blue:2ghz";
 			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
 		};
 
-		5ghz {
+		led-5ghz {
 			label = "bcm53xx:blue:5ghz";
 			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
 		};
@@ -43,7 +51,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
@@ -51,6 +59,48 @@
 	};
 };
 
+&gmac0 {
+	nvmem-cells = <&et0macaddr>;
+	nvmem-cell-names = "mac-address";
+};
+
+
+&pcie0 {
+	#address-cells = <3>;
+	#size-cells = <2>;
+
+	bridge@0,0 {
+		reg = <0x0000 0 0 0 0>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		wifi@0,0 {
+			compatible = "brcm,bcm4366-fmac", "brcm,bcm4329-fmac";
+			reg = <0x0000 0 0 0 0>;
+			brcm,ccode-map = "AU-AU-920", "CA-CA-892", "GB-DE-964", "NZ-AU-920", "US-US-825";
+		};
+	};
+};
+
+&pcie1 {
+	#address-cells = <3>;
+	#size-cells = <2>;
+
+	bridge@0,0 {
+		reg = <0x0000 0 0 0 0>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		wifi@0,0 {
+			compatible = "brcm,bcm4366-fmac", "brcm,bcm4329-fmac";
+			reg = <0x0000 0 0 0 0>;
+			brcm,ccode-map = "AU-AU-920", "CA-CA-892", "GB-DE-964", "NZ-AU-920", "US-US-825";
+		};
+	};
+};
+
 &spi_nor {
 	status = "okay";
 };
@@ -60,19 +110,23 @@
 
 	ports {
 		port@0 {
-			reg = <0>;
 			label = "poe";
 		};
 
 		port@1 {
-			reg = <1>;
 			label = "lan";
 		};
 
 		port@5 {
-			reg = <5>;
 			label = "cpu";
-			ethernet = <&gmac0>;
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts b/arch/arm/boot/dts/broadcom/bcm47094-luxul-xbr-4500.dts
index b959a9504eea..cf95af9db1e6 100644
--- a/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47094-luxul-xbr-4500.dts
@@ -25,18 +25,22 @@
 	nvram@1eff0000 {
 		compatible = "brcm,nvram";
 		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+			#nvmem-cell-cells = <1>;
+		};
 	};
 
 	leds {
 		compatible = "gpio-leds";
 
-		status {
+		led-status {
 			label = "bcm53xx:green:status";
 			gpios = <&chipcommon 20 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "timer";
 		};
 
-		usb3 {
+		led-usb3 {
 			label = "bcm53xx:green:usb3";
 			gpios = <&chipcommon 19 GPIO_ACTIVE_HIGH>;
 			trigger-sources = <&ohci_port1>, <&ehci_port1>,
@@ -49,7 +53,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
@@ -61,6 +65,11 @@
 	vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
 };
 
+&gmac0 {
+	nvmem-cells = <&et0macaddr 0>;
+	nvmem-cell-names = "mac-address";
+};
+
 &spi_nor {
 	status = "okay";
 };
@@ -74,34 +83,37 @@
 
 	ports {
 		port@0 {
-			reg = <0>;
 			label = "wan";
+			nvmem-cells = <&et0macaddr 1>;
+			nvmem-cell-names = "mac-address";
 		};
 
 		port@1 {
-			reg = <1>;
 			label = "lan4";
 		};
 
 		port@2 {
-			reg = <2>;
 			label = "lan3";
 		};
 
 		port@3 {
-			reg = <3>;
 			label = "lan2";
 		};
 
 		port@4 {
-			reg = <4>;
 			label = "lan1";
 		};
 
 		port@5 {
-			reg = <5>;
 			label = "cpu";
-			ethernet = <&gmac0>;
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts b/arch/arm/boot/dts/broadcom/bcm47094-luxul-xwc-2000.dts
index b0d8a688141d..992c19e1cfa1 100644
--- a/arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47094-luxul-xwc-2000.dts
@@ -22,10 +22,18 @@
 		      <0x88000000 0x18000000>;
 	};
 
+	nvram@1eff0000 {
+		compatible = "brcm,nvram";
+		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 
-		status	{
+		led-status {
 			label = "bcm53xx:green:status";
 			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "timer";
@@ -34,10 +42,8 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 19 GPIO_ACTIVE_LOW>;
@@ -49,6 +55,11 @@
 	status = "okay";
 };
 
+&gmac0 {
+	nvmem-cells = <&et0macaddr>;
+	nvmem-cell-names = "mac-address";
+};
+
 &spi_nor {
 	status = "okay";
 };
@@ -58,14 +69,19 @@
 
 	ports {
 		port@0 {
-			reg = <0>;
 			label = "lan";
 		};
 
 		port@5 {
-			reg = <5>;
 			label = "cpu";
-			ethernet = <&gmac0>;
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts b/arch/arm/boot/dts/broadcom/bcm47094-luxul-xwr-3100.dts
index cbe8c8e4a301..4d0ba315a204 100644
--- a/arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47094-luxul-xwr-3100.dts
@@ -9,7 +9,7 @@
 #include "bcm5301x-nand-cs0-bch4.dtsi"
 
 / {
-	compatible = "luxul,xwr-3100v1", "brcm,bcm47094", "brcm,bcm4708";
+	compatible = "luxul,xwr-3100-v1", "brcm,bcm47094", "brcm,bcm4708";
 	model = "Luxul XWR-3100 V1";
 
 	chosen {
@@ -25,43 +25,47 @@
 	nvram@1eff0000 {
 		compatible = "brcm,nvram";
 		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+			#nvmem-cell-cells = <1>;
+		};
 	};
 
 	leds {
 		compatible = "gpio-leds";
 
-		power	{
+		led-power {
 			label = "bcm53xx:green:power";
 			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		lan3	{
+		led-lan3 {
 			label = "bcm53xx:green:lan3";
 			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
 		};
 
-		lan4	{
+		led-lan4 {
 			label = "bcm53xx:green:lan4";
 			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
 		};
 
-		wan	{
+		led-wan {
 			label = "bcm53xx:green:wan";
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 		};
 
-		lan1	{
+		led-lan1 {
 			label = "bcm53xx:green:lan1";
 			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
 		};
 
-		lan2	{
+		led-lan2 {
 			label = "bcm53xx:green:lan2";
 			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
 		};
 
-		usb3	{
+		led-usb3 {
 			label = "bcm53xx:green:usb3";
 			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
 			trigger-sources = <&ohci_port1>, <&ehci_port1>,
@@ -69,18 +73,18 @@
 			linux,default-trigger = "usbport";
 		};
 
-		status	{
+		led-status {
 			label = "bcm53xx:green:status";
 			gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "timer";
 		};
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:green:2ghz";
 			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
 		};
 
-		5ghz {
+		led-5ghz {
 			label = "bcm53xx:green:5ghz";
 			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
 		};
@@ -89,7 +93,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
@@ -101,6 +105,11 @@
 	vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
 };
 
+&gmac0 {
+	nvmem-cells = <&et0macaddr 0>;
+	nvmem-cell-names = "mac-address";
+};
+
 &spi_nor {
 	status = "okay";
 };
@@ -114,34 +123,37 @@
 
 	ports {
 		port@0 {
-			reg = <0>;
 			label = "lan4";
 		};
 
 		port@1 {
-			reg = <1>;
 			label = "lan3";
 		};
 
 		port@2 {
-			reg = <2>;
 			label = "lan2";
 		};
 
 		port@3 {
-			reg = <3>;
 			label = "lan1";
 		};
 
 		port@4 {
-			reg = <4>;
 			label = "wan";
+			nvmem-cells = <&et0macaddr 5>;
+			nvmem-cell-names = "mac-address";
 		};
 
 		port@5 {
-			reg = <5>;
 			label = "cpu";
-			ethernet = <&gmac0>;
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/bcm47094-luxul-xwr-3150-v1.dts b/arch/arm/boot/dts/broadcom/bcm47094-luxul-xwr-3150-v1.dts
index 9efcb2424228..83c429afc297 100644
--- a/arch/arm/boot/dts/bcm47094-luxul-xwr-3150-v1.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47094-luxul-xwr-3150-v1.dts
@@ -27,19 +27,20 @@
 		reg = <0x1eff0000 0x10000>;
 
 		et0macaddr: et0macaddr {
+			#nvmem-cell-cells = <1>;
 		};
 	};
 
 	leds {
 		compatible = "gpio-leds";
 
-		power	{
+		led-power {
 			label = "bcm53xx:green:power";
 			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		usb3	{
+		led-usb3 {
 			label = "bcm53xx:green:usb3";
 			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
 			trigger-sources = <&ohci_port1>, <&ehci_port1>,
@@ -47,18 +48,18 @@
 			linux,default-trigger = "usbport";
 		};
 
-		status	{
+		led-status {
 			label = "bcm53xx:green:status";
 			gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "timer";
 		};
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:green:2ghz";
 			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
 		};
 
-		5ghz {
+		led-5ghz {
 			label = "bcm53xx:green:5ghz";
 			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
 		};
@@ -67,7 +68,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
@@ -76,10 +77,46 @@
 };
 
 &gmac0 {
-	nvmem-cells = <&et0macaddr>;
+	nvmem-cells = <&et0macaddr 0>;
 	nvmem-cell-names = "mac-address";
 };
 
+&pcie0 {
+	#address-cells = <3>;
+	#size-cells = <2>;
+
+	bridge@0,0 {
+		reg = <0x0000 0 0 0 0>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		wifi@0,0 {
+			compatible = "brcm,bcm4366-fmac", "brcm,bcm4329-fmac";
+			reg = <0x0000 0 0 0 0>;
+			brcm,ccode-map = "AU-AU-953", "CA-CA-946", "GB-E0-846", "NZ-AU-953", "US-Q2-930";
+		};
+	};
+};
+
+&pcie1 {
+	#address-cells = <3>;
+	#size-cells = <2>;
+
+	bridge@0,0 {
+		reg = <0x0000 0 0 0 0>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		wifi@0,0 {
+			compatible = "brcm,bcm4366-fmac", "brcm,bcm4329-fmac";
+			reg = <0x0000 0 0 0 0>;
+			brcm,ccode-map = "AU-AU-953", "CA-CA-946", "GB-E0-846", "NZ-AU-953", "US-Q2-930";
+		};
+	};
+};
+
 &usb3 {
 	vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
 };
@@ -97,34 +134,37 @@
 
 	ports {
 		port@0 {
-			reg = <0>;
 			label = "lan4";
 		};
 
 		port@1 {
-			reg = <1>;
 			label = "lan3";
 		};
 
 		port@2 {
-			reg = <2>;
 			label = "lan2";
 		};
 
 		port@3 {
-			reg = <3>;
 			label = "lan1";
 		};
 
 		port@4 {
-			reg = <4>;
 			label = "wan";
+			nvmem-cells = <&et0macaddr 5>;
+			nvmem-cell-names = "mac-address";
 		};
 
 		port@5 {
-			reg = <5>;
 			label = "cpu";
-			ethernet = <&gmac0>;
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/bcm47094-netgear-r8500.dts b/arch/arm/boot/dts/broadcom/bcm47094-netgear-r8500.dts
index 42097a4c2659..76d562610654 100644
--- a/arch/arm/boot/dts/bcm47094-netgear-r8500.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47094-netgear-r8500.dts
@@ -25,38 +25,38 @@
 	leds {
 		compatible = "gpio-leds";
 
-		power0 {
+		led-power0 {
 			label = "bcm53xx:white:power";
 			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
 		};
 
-		power1 {
+		led-power1 {
 			label = "bcm53xx:amber:power";
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 		};
 
-		5ghz-1 {
+		led-5ghz-1 {
 			label = "bcm53xx:white:5ghz-1";
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
 		};
 
-		5ghz-2 {
+		led-5ghz-2 {
 			label = "bcm53xx:white:5ghz-2";
 			gpios = <&chipcommon 12 GPIO_ACTIVE_LOW>;
 		};
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:white:2ghz";
 			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
 		};
 
-		usb2 {
+		led-usb2 {
 			label = "bcm53xx:white:usb2";
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
 		};
 
-		usb3 {
+		led-usb3 {
 			label = "bcm53xx:white:usb3";
 			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
 		};
@@ -65,25 +65,25 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		brightness {
+		button-brightness {
 			label = "Backlight";
 			linux,code = <KEY_BRIGHTNESS_ZERO>;
 			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
 		};
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 20 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm47094-phicomm-k3.dts b/arch/arm/boot/dts/broadcom/bcm47094-phicomm-k3.dts
index a2566ad4619c..bb1bc4e61bc2 100644
--- a/arch/arm/boot/dts/bcm47094-phicomm-k3.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47094-phicomm-k3.dts
@@ -22,7 +22,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
@@ -55,7 +55,7 @@
 			reg = <0x0080000 0x0100000>;
 		};
 
-		partition@180000{
+		partition@180000 {
 			label = "phicomm";
 			reg = <0x0180000 0x0280000>;
 			read-only;
diff --git a/arch/arm/boot/dts/bcm47094.dtsi b/arch/arm/boot/dts/broadcom/bcm47094.dtsi
index 6282363313e1..6282363313e1 100644
--- a/arch/arm/boot/dts/bcm47094.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm47094.dtsi
diff --git a/arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts b/arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dts
index 57ca1cfaecd8..ac44c745bdf8 100644
--- a/arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-1440.dts
@@ -23,13 +23,12 @@
 	leds {
 		compatible = "gpio-leds";
 
-		wlan {
+		led-wlan {
 			label = "bcm53xx:blue:wlan";
 			gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "default-off";
 		};
 
-		system {
+		led-system {
 			label = "bcm53xx:green:system";
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "timer";
@@ -39,10 +38,29 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
 		};
 	};
 };
+
+&gmac0 {
+	phy-mode = "rgmii";
+	phy-handle = <&bcm54210e>;
+
+	/delete-node/ fixed-link;
+
+	mdio {
+		/delete-node/ switch@1e;
+
+		bcm54210e: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
+
+&gmac1 {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/bcm47189-luxul-xap-810.dts b/arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-810.dts
index 2e1a7e382cb7..fd071da26cfa 100644
--- a/arch/arm/boot/dts/bcm47189-luxul-xap-810.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47189-luxul-xap-810.dts
@@ -20,36 +20,34 @@
 		reg = <0x00000000 0x08000000>;
 	};
 
-	leds {
+	leds-0 {
 		compatible = "gpio-leds";
 
-		5ghz {
+		led-5ghz {
 			label = "bcm53xx:blue:5ghz";
 			gpios = <&chipcommon 11 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "default-off";
 		};
 
-		system {
+		led-system {
 			label = "bcm53xx:green:system";
 			gpios = <&chipcommon 15 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "timer";
 		};
 	};
 
-	pcie0_leds {
+	leds-1 {
 		compatible = "gpio-leds";
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:blue:2ghz";
 			gpios = <&pcie0_chipcommon 3 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "default-off";
 		};
 	};
 
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
@@ -83,3 +81,22 @@
 		};
 	};
 };
+
+&gmac0 {
+	phy-mode = "rgmii";
+	phy-handle = <&bcm54210e>;
+
+	/delete-node/ fixed-link;
+
+	mdio {
+		/delete-node/ switch@1e;
+
+		bcm54210e: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
+
+&gmac1 {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/bcm47189-tenda-ac9.dts b/arch/arm/boot/dts/broadcom/bcm47189-tenda-ac9.dts
index 07eb3a8287d6..3ac6cac541ca 100644
--- a/arch/arm/boot/dts/bcm47189-tenda-ac9.dts
+++ b/arch/arm/boot/dts/broadcom/bcm47189-tenda-ac9.dts
@@ -20,37 +20,37 @@
 		reg = <0x00000000 0x08000000>;
 	};
 
-	leds {
+	leds-0 {
 		compatible = "gpio-leds";
 
-		usb {
+		led-usb {
 			label = "bcm53xx:blue:usb";
 			gpios = <&chipcommon 1 GPIO_ACTIVE_HIGH>;
 			trigger-sources = <&ohci_port1>, <&ehci_port1>;
 			linux,default-trigger = "usbport";
 		};
 
-		wps {
+		led-wps {
 			label = "bcm53xx:blue:wps";
 			gpios = <&chipcommon 10 GPIO_ACTIVE_HIGH>;
 		};
 
-		5ghz {
+		led-5ghz {
 			label = "bcm53xx:blue:5ghz";
 			gpios = <&chipcommon 11 GPIO_ACTIVE_HIGH>;
 		};
 
-		system {
+		led-system {
 			label = "bcm53xx:blue:system";
 			gpios = <&chipcommon 15 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "timer";
 		};
 	};
 
-	pcie0_leds {
+	leds-1 {
 		compatible = "gpio-leds";
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:blue:2ghz";
 			gpios = <&pcie0_chipcommon 3 GPIO_ACTIVE_HIGH>;
 		};
@@ -59,19 +59,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 9 GPIO_ACTIVE_LOW>;
@@ -111,34 +111,27 @@
 
 	ports {
 		port@0 {
-			reg = <0>;
 			label = "wan";
 		};
 
 		port@1 {
-			reg = <1>;
 			label = "lan1";
 		};
 
 		port@2 {
-			reg = <2>;
 			label = "lan2";
 		};
 
 		port@3 {
-			reg = <3>;
 			label = "lan3";
 		};
 
 		port@4 {
-			reg = <4>;
 			label = "lan4";
 		};
 
-		port@5 {
-			reg = <5>;
+		port@8 {
 			label = "cpu";
-			ethernet = <&gmac0>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/broadcom/bcm47622.dtsi b/arch/arm/boot/dts/broadcom/bcm47622.dtsi
new file mode 100644
index 000000000000..485863f9c420
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm47622.dtsi
@@ -0,0 +1,164 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm47622", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CA7_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x2>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x3>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&CA7_0>, <&CA7_1>,
+			<&CA7_2>, <&CA7_3>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+
+		uart_clk: uart-clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clocks = <&periph_clk>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+
+		hsspi_pll: hsspi-pll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xff800000 0x800000>;
+
+		hsspi: spi@1000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm47622-hsspi", "brcm,bcmbca-hsspi-v1.0";
+			reg = <0x1000 0x600>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsspi_pll &hsspi_pll>;
+			clock-names = "hsspi", "pll";
+			num-cs = <8>;
+			status = "disabled";
+		};
+
+		nand_controller: nand-controller@1800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,nand-bcm63138", "brcm,brcmnand-v7.1", "brcm,brcmnand";
+			reg = <0x1800 0x600>, <0x2000 0x10>;
+			reg-names = "nand", "nand-int-base";
+			status = "disabled";
+
+			nandcs: nand@0 {
+				compatible = "brcm,nandcs";
+				reg = <0>;
+			};
+		};
+
+		uart0: serial@12000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x12000 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm53015-meraki-mr26.dts b/arch/arm/boot/dts/broadcom/bcm53015-meraki-mr26.dts
new file mode 100644
index 000000000000..08abfdc63d18
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm53015-meraki-mr26.dts
@@ -0,0 +1,187 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Meraki MR26 / Codename: Venom
+ *
+ * Copyright (C) 2022 Christian Lamparter <chunkeey@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+	compatible = "meraki,mr26", "brcm,bcm53015", "brcm,bcm4708";
+	model = "Meraki MR26";
+
+	memory@0 {
+		reg = <0x00000000 0x08000000>;
+		device_type = "memory";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			function = LED_FUNCTION_FAULT;
+			color = <LED_COLOR_ID_AMBER>;
+			gpios = <&chipcommon 13 GPIO_ACTIVE_HIGH>;
+			panic-indicator;
+		};
+		led-1 {
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_WHITE>;
+			gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		key-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&uart0 {
+	clock-frequency = <50000000>;
+	/delete-property/ clocks;
+};
+
+&uart1 {
+	status = "disabled";
+};
+
+&gmac0 {
+	status = "okay";
+
+	nvmem-cells = <&macaddr_board_config_66>;
+	nvmem-cell-names = "mac-address";
+};
+
+&gmac1 {
+	status = "disabled";
+};
+&gmac2 {
+	status = "disabled";
+};
+&gmac3 {
+	status = "disabled";
+};
+
+&nandcs {
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <0x1>;
+		#size-cells = <0x1>;
+
+		partition@0 {
+			label = "u-boot";
+			reg = <0x0 0x200000>;
+			read-only;
+		};
+
+		partition@200000 {
+			label = "u-boot-env";
+			reg = <0x200000 0x200000>;
+			/* empty */
+		};
+
+		partition@400000 {
+			label = "u-boot-backup";
+			reg = <0x400000 0x200000>;
+			/* empty */
+		};
+
+		partition@600000 {
+			label = "u-boot-env-backup";
+			reg = <0x600000 0x200000>;
+			/* empty */
+		};
+
+		partition@800000 {
+			compatible = "linux,ubi";
+			label = "ubi";
+			reg = <0x800000 0x7780000>;
+
+			volumes {
+				ubi-volume-board-config {
+					volname = "board-config";
+
+					nvmem-layout {
+						compatible = "fixed-layout";
+						#address-cells = <1>;
+						#size-cells = <1>;
+
+						macaddr_board_config_66: macaddr@66 {
+							reg = <0x66 0x6>;
+						};
+					};
+				};
+			};
+		};
+	};
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			label = "poe";
+		};
+
+		port@5 {
+			label = "cpu";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinmux_i2c>;
+
+	clock-frequency = <100000>;
+
+	ina219@40 {
+		compatible = "ti,ina219"; /* PoE power */
+		reg = <0x40>;
+		shunt-resistor = <60000>; /* = 60 mOhms */
+	};
+
+	eeprom@56 {
+		compatible = "atmel,24c64";
+		reg = <0x56>;
+		pagesize = <32>;
+		read-only;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/* it's empty */
+	};
+};
+
+&thermal {
+	status = "disabled";
+	/* does not work, reads 418 degree Celsius */
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm53016-dlink-dwl-8610ap.dts b/arch/arm/boot/dts/broadcom/bcm53016-dlink-dwl-8610ap.dts
new file mode 100644
index 000000000000..c1f54391746f
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm53016-dlink-dwl-8610ap.dts
@@ -0,0 +1,131 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "bcm4709.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "D-Link DWL-8610AP";
+	compatible = "dlink,dwl-8610ap", "brcm,bcm53016", "brcm,bcm4708";
+
+	memory@0 {
+		device_type = "memory";
+		/* 512 MB RAM in 2 x Macronix D9PSH chips */
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power {
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		led-diag {
+			/* Actually "diag" unclear what this means */
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-wlan-2g {
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
+		};
+
+		led-wlan-5g {
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		button-reset {
+			debounce-interval = <100>;
+			wakeup-source;
+			linux,code = <KEY_RESTART>;
+			label = "reset";
+			/* This GPIO is actually stored in NVRAM, but it's not gonna change */
+			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	/*
+	 * Flash memory at 0x1e000000-0x1fffffff
+	 * Macronix 32 64KB blocks; total size 2MB, same that can be
+	 * found attached to the spi_nor SPI controller.
+	 */
+	nvram@1e080000 {
+		compatible = "brcm,nvram";
+		reg = <0x1e080000 0x00020000>;
+
+		et0macaddr: et0macaddr {
+		};
+
+		et1macaddr: et1macaddr {
+		};
+	};
+};
+
+&gmac0 {
+	nvmem-cells = <&et0macaddr>;
+	nvmem-cell-names = "mac-address";
+};
+
+&gmac1 {
+	nvmem-cells = <&et1macaddr>;
+	nvmem-cell-names = "mac-address";
+};
+
+&spi_nor {
+	/* Serial SPI NOR Flash MX 25L1606E */
+	status = "okay";
+};
+
+&nandcs {
+	/*
+	 * Spansion S34ML01G100TFI00 128 MB NAND Flash memory
+	 *
+	 * This ECC is a bit unorthodox but it is what the stock firmware
+	 * is using, so to be able to mount the original partitions
+	 * this is necessary.
+	 */
+	nand-ecc-strength = <5>;
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/* This is named nflash1.trx in CFE */
+		trx@0 {
+			label = "firmware";
+			reg = <0x00000000 0x02800000>;
+			compatible = "brcm,trx";
+		};
+
+		/* This is named nflash1.trx2 in CFE */
+		trx2@2800000 {
+			label = "firmware2";
+			reg = <0x02800000 0x02800000>;
+			compatible = "brcm,trx";
+		};
+
+		/* This is named nflash1.rwfs in CFE */
+		free@5000000 {
+			label = "free";
+			reg = <0x05000000 0x03000000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm53016-meraki-mr32.dts b/arch/arm/boot/dts/broadcom/bcm53016-meraki-mr32.dts
index 66c64a6ec414..45bd27906f29 100644
--- a/arch/arm/boot/dts/bcm53016-meraki-mr32.dts
+++ b/arch/arm/boot/dts/broadcom/bcm53016-meraki-mr32.dts
@@ -13,7 +13,7 @@
 #include <dt-bindings/leds/common.h>
 
 / {
-	compatible = "meraki,mr32", "brcm,brcm53016", "brcm,bcm4708";
+	compatible = "meraki,mr32", "brcm,bcm53016", "brcm,bcm4708";
 	model = "Meraki MR32";
 
 	chosen {
@@ -47,10 +47,8 @@
 
 	keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 21 GPIO_ACTIVE_LOW>;
@@ -60,7 +58,7 @@
 	pwm-leds {
 		compatible = "pwm-leds";
 
-		red {
+		led-0 {
 			/* SYS-LED 1 - Tricolor */
 			function = LED_FUNCTION_INDICATOR;
 			color = <LED_COLOR_ID_RED>;
@@ -68,7 +66,7 @@
 			max-brightness = <255>;
 		};
 
-		green {
+		led-1 {
 			/* SYS-LED 1 - Tricolor */
 			function = LED_FUNCTION_POWER;
 			color = <LED_COLOR_ID_GREEN>;
@@ -76,7 +74,7 @@
 			max-brightness = <255>;
 		};
 
-		blue {
+		led-2 {
 			/* SYS-LED 1 - Tricolor */
 			function = LED_FUNCTION_INDICATOR;
 			color = <LED_COLOR_ID_BLUE>;
@@ -127,8 +125,6 @@
 };
 
 &nandcs {
-	nand-ecc-algo = "hw";
-
 	partitions {
 		/*
 		 * The partition autodetection does not work for this device.
@@ -142,31 +138,31 @@
 		#address-cells = <0x1>;
 		#size-cells = <0x1>;
 
-		partition0@0 {
+		partition@0 {
 			label = "u-boot";
 			reg = <0x0 0x100000>;
 			read-only;
 		};
 
-		partition1@100000 {
+		partition@100000 {
 			label = "bootkernel1";
 			reg = <0x100000 0x300000>;
 			read-only;
 		};
 
-		partition2@400000 {
+		partition@400000 {
 			label = "nvram";
 			reg = <0x400000 0x100000>;
 			read-only;
 		};
 
-		partition3@500000 {
+		partition@500000 {
 			label = "bootkernel2";
 			reg = <0x500000 0x300000>;
 			read-only;
 		};
 
-		partition4@800000 {
+		partition@800000 {
 			label = "ubi";
 			reg = <0x800000 0x7780000>;
 		};
@@ -178,20 +174,25 @@
 
 	ports {
 		port@0 {
-			reg = <0>;
 			label = "poe";
 		};
 
 		port@5 {
-			reg = <5>;
 			label = "cpu";
-			ethernet = <&gmac0>;
 
 			fixed-link {
 				speed = <1000>;
-				duplex-full;
+				full-duplex;
 			};
 		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
 	};
 };
 
@@ -214,11 +215,15 @@
 		reg = <0x50>;
 		pagesize = <32>;
 		read-only;
-		#address-cells = <1>;
-		#size-cells = <1>;
 
-		mac_address: mac-address@66 {
-			reg = <0x66 0x6>;
+		nvmem-layout {
+			compatible = "fixed-layout";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			mac_address: mac-address@66 {
+				reg = <0x66 0x6>;
+			};
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/bcm5301x-nand-cs0-bch1.dtsi b/arch/arm/boot/dts/broadcom/bcm5301x-nand-cs0-bch1.dtsi
index c349e8f0afc5..c349e8f0afc5 100644
--- a/arch/arm/boot/dts/bcm5301x-nand-cs0-bch1.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm5301x-nand-cs0-bch1.dtsi
diff --git a/arch/arm/boot/dts/bcm5301x-nand-cs0-bch4.dtsi b/arch/arm/boot/dts/broadcom/bcm5301x-nand-cs0-bch4.dtsi
index 18e25e302b13..18e25e302b13 100644
--- a/arch/arm/boot/dts/bcm5301x-nand-cs0-bch4.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm5301x-nand-cs0-bch4.dtsi
diff --git a/arch/arm/boot/dts/bcm5301x-nand-cs0-bch8.dtsi b/arch/arm/boot/dts/broadcom/bcm5301x-nand-cs0-bch8.dtsi
index c8e56d30bd6f..c8e56d30bd6f 100644
--- a/arch/arm/boot/dts/bcm5301x-nand-cs0-bch8.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm5301x-nand-cs0-bch8.dtsi
diff --git a/arch/arm/boot/dts/bcm5301x-nand-cs0.dtsi b/arch/arm/boot/dts/broadcom/bcm5301x-nand-cs0.dtsi
index be9a00ff752d..be9a00ff752d 100644
--- a/arch/arm/boot/dts/bcm5301x-nand-cs0.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm5301x-nand-cs0.dtsi
diff --git a/arch/arm/boot/dts/broadcom/bcm5301x.dtsi b/arch/arm/boot/dts/broadcom/bcm5301x.dtsi
new file mode 100644
index 000000000000..f06a178a9240
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm5301x.dtsi
@@ -0,0 +1,136 @@
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * Generic DTS part for all BCM53010, BCM53011, BCM53012, BCM53014, BCM53015,
+ * BCM53016, BCM53017, BCM53018, BCM4707, BCM4708 and BCM4709 SoCs
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+#include "bcm-ns.dtsi"
+
+/ {
+	mpcore-bus@19000000 {
+		a9pll: arm_clk@0 {
+			#clock-cells = <0>;
+			compatible = "brcm,nsp-armpll";
+			clocks = <&osc>;
+			reg = <0x00000 0x1000>;
+		};
+
+		watchdog@20620 {
+			compatible = "arm,cortex-a9-twd-wdt";
+			reg = <0x20620 0x20>;
+			interrupts = <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) |
+						  IRQ_TYPE_EDGE_RISING)>;
+			clocks = <&periph_clk>;
+		};
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		osc: oscillator {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <25000000>;
+		};
+
+		iprocmed: iprocmed {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
+			clock-div = <2>;
+			clock-mult = <1>;
+		};
+
+		iprocslow: iprocslow {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			clocks = <&genpll BCM_NSP_GENPLL_IPROCFAST_CLK>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+
+		periph_clk: periph_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-factor-clock";
+			clocks = <&a9pll>;
+			clock-div = <2>;
+			clock-mult = <1>;
+		};
+	};
+
+	i2c0: i2c@18009000 {
+		compatible = "brcm,iproc-i2c";
+		reg = <0x18009000 0x50>;
+		interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clock-frequency = <100000>;
+		status = "disabled";
+	};
+
+	dmu-bus@1800c000 {
+		cru-bus@100 {
+			lcpll0: clock-controller@100 {
+				#clock-cells = <1>;
+				compatible = "brcm,nsp-lcpll0";
+				reg = <0x100 0x14>;
+				clocks = <&osc>;
+				clock-output-names = "lcpll0", "pcie_phy",
+						     "sdio", "ddr_phy";
+			};
+
+			genpll: clock-controller@140 {
+				#clock-cells = <1>;
+				compatible = "brcm,nsp-genpll";
+				reg = <0x140 0x24>;
+				clocks = <&osc>;
+				clock-output-names = "genpll", "phy",
+						     "ethernetclk",
+						     "usbclk", "iprocfast",
+						     "sata1", "sata2";
+			};
+		};
+	};
+
+	spi@18029200 {
+		compatible = "brcm,spi-nsp-qspi", "brcm,spi-bcm-qspi";
+		reg = <0x18029200 0x184>,
+		      <0x18029000 0x124>,
+		      <0x1811b408 0x004>,
+		      <0x180293a0 0x01c>;
+		reg-names = "mspi", "bspi", "intr_regs", "intr_status_reg";
+		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "mspi_done",
+				  "mspi_halted",
+				  "spi_lr_fullness_reached",
+				  "spi_lr_session_aborted",
+				  "spi_lr_impatient",
+				  "spi_lr_session_done",
+				  "spi_lr_overread";
+		clocks = <&iprocmed>;
+		num-cs = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		spi_nor: flash@0 {
+			compatible = "jedec,spi-nor";
+			reg = <0>;
+			spi-max-frequency = <20000000>;
+			status = "disabled";
+
+			partitions {
+				compatible = "brcm,bcm947xx-cfe-partitions";
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm53340-ubnt-unifi-switch8.dts b/arch/arm/boot/dts/broadcom/bcm53340-ubnt-unifi-switch8.dts
index 2e7fda9b998c..08cf1220b655 100644
--- a/arch/arm/boot/dts/bcm53340-ubnt-unifi-switch8.dts
+++ b/arch/arm/boot/dts/broadcom/bcm53340-ubnt-unifi-switch8.dts
@@ -32,9 +32,8 @@
 
 &qspi {
 	status = "okay";
-	bspi-sel = <0>;
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "m25p80";
 		reg = <0>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/bcm53573.dtsi b/arch/arm/boot/dts/broadcom/bcm53573.dtsi
index 3f03a381db0f..2df80740d181 100644
--- a/arch/arm/boot/dts/bcm53573.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm53573.dtsi
@@ -127,6 +127,9 @@
 
 		pcie0: pcie@2000 {
 			reg = <0x00002000 0x1000>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
 		};
 
 		usb2: usb2@4000 {
@@ -156,8 +159,6 @@
 			};
 
 			ohci: usb@d000 {
-				#usb-cells = <0>;
-
 				compatible = "generic-ohci";
 				reg = <0xd000 0x1000>;
 				interrupt-parent = <&gic>;
@@ -180,6 +181,12 @@
 
 		gmac0: ethernet@5000 {
 			reg = <0x5000 0x1000>;
+			phy-mode = "internal";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
 
 			mdio {
 				#address-cells = <1>;
@@ -191,10 +198,44 @@
 
 					status = "disabled";
 
-					/* ports are defined in board DTS */
 					ports {
 						#address-cells = <1>;
 						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+						};
+
+						port@1 {
+							reg = <1>;
+						};
+
+						port@2 {
+							reg = <2>;
+						};
+
+						port@3 {
+							reg = <3>;
+						};
+
+						port@4 {
+							reg = <4>;
+						};
+
+						port@5 {
+							reg = <5>;
+							ethernet = <&gmac1>;
+
+							fixed-link {
+								speed = <1000>;
+								full-duplex;
+							};
+						};
+
+						port@8 {
+							reg = <8>;
+							ethernet = <&gmac0>;
+						};
 					};
 				};
 			};
@@ -202,6 +243,12 @@
 
 		gmac1: ethernet@b000 {
 			reg = <0xb000 0x1000>;
+			phy-mode = "internal";
+
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
 		};
 
 		pmu@12000 {
diff --git a/arch/arm/boot/dts/bcm63138.dtsi b/arch/arm/boot/dts/broadcom/bcm63138.dtsi
index cca49a2e2d62..4ec568586b14 100644
--- a/arch/arm/boot/dts/bcm63138.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm63138.dtsi
@@ -9,8 +9,8 @@
 / {
 	#address-cells = <1>;
 	#size-cells = <1>;
-	compatible = "brcm,bcm63138";
-	model = "Broadcom BCM63138 DSL SoC";
+	compatible = "brcm,bcm63138", "brcm,bcmbca";
+	model = "Broadcom BCM963138 Reference Board";
 	interrupt-parent = <&gic>;
 
 	aliases {
@@ -66,6 +66,12 @@
 			clock-div = <4>;
 			clock-mult = <1>;
 		};
+
+		hsspi_pll: hsspi-pll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <400000000>;
+		};
 	};
 
 	/* ARM bus */
@@ -178,13 +184,69 @@
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
-		ranges = <0 0xfffe8000 0x8100>;
+		ranges = <0 0xfffe8000 0x10000>;
 
 		timer: timer@80 {
 			compatible = "brcm,bcm6328-timer", "syscon";
 			reg = <0x80 0x3c>;
 		};
 
+		/* GPIOs 0 .. 31 */
+		gpio0: gpio@100 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x100 0x04>, <0x114 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 32 .. 63 */
+		gpio1: gpio@104 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x104 0x04>, <0x118 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 64 .. 95 */
+		gpio2: gpio@108 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x108 0x04>, <0x11c 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 96 .. 127 */
+		gpio3: gpio@10c {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x10c 0x04>, <0x120 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 128 .. 159 */
+		gpio4: gpio@110 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x110 0x04>, <0x124 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		rng@300 {
+			compatible = "brcm,iproc-rng200";
+			reg = <0x300 0x28>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
 		serial0: serial@600 {
 			compatible = "brcm,bcm6345-uart";
 			reg = <0x600 0x1b>;
@@ -203,6 +265,26 @@
 			status = "disabled";
 		};
 
+		leds: led-controller@700 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm63138-leds";
+			reg = <0x700 0xdc>;
+			status = "disabled";
+		};
+
+		hsspi: spi@1000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm63138-hsspi", "brcm,bcmbca-hsspi-v1.0";
+			reg = <0x1000 0x600>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsspi_pll &hsspi_pll>;
+			clock-names = "hsspi", "pll";
+			num-cs = <8>;
+			status = "disabled";
+		};
+
 		nand_controller: nand-controller@2000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -211,7 +293,18 @@
 			reg-names = "nand", "nand-int-base";
 			status = "disabled";
 			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "nand";
+			interrupt-names = "nand_ctlrdy";
+
+			nandcs: nand@0 {
+				compatible = "brcm,nandcs";
+				reg = <0>;
+			};
+		};
+
+		serial@4400 {
+			compatible = "brcm,bcm63138-hs-uart", "brcm,bcmbca-hs-uart";
+			reg = <0x4400 0x1e0>;
+			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
 		bootlut: bootlut@8000 {
@@ -219,6 +312,19 @@
 			reg = <0x8000 0x50>;
 		};
 
+		pl081_dma: dma-controller@d000 {
+			compatible = "arm,pl081", "arm,primecell";
+			// The magic B105F00D info is missing
+			arm,primecell-periphid = <0x00041081>;
+			reg = <0xd000 0x1000>;
+			interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+			memcpy-burst-size = <256>;
+			memcpy-bus-width = <32>;
+			clocks = <&periph_clk>;
+			clock-names = "apb_pclk";
+			#dma-cells = <2>;
+		};
+
 		reboot {
 			compatible = "syscon-reboot";
 			regmap = <&timer>;
diff --git a/arch/arm/boot/dts/broadcom/bcm63148.dtsi b/arch/arm/boot/dts/broadcom/bcm63148.dtsi
new file mode 100644
index 000000000000..e071cddb28fc
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm63148.dtsi
@@ -0,0 +1,201 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm63148", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		B15_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "brcm,brahma-b15";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		B15_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "brcm,brahma-b15";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a15-pmu";
+		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&B15_0>, <&B15_1>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <50000000>;
+		};
+
+		hsspi_pll: hsspi-pll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <400000000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@80030000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x80030000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a15-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) |
+					IRQ_TYPE_LEVEL_HIGH)>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xfffe8000 0x8000>;
+
+		/* GPIOs 0 .. 31 */
+		gpio0: gpio@100 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x100 0x04>, <0x114 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 32 .. 63 */
+		gpio1: gpio@104 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x104 0x04>, <0x118 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 64 .. 95 */
+		gpio2: gpio@108 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x108 0x04>, <0x11c 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 96 .. 127 */
+		gpio3: gpio@10c {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x10c 0x04>, <0x120 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 128 .. 159 */
+		gpio4: gpio@110 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x110 0x04>, <0x124 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		rng@300 {
+			compatible = "brcm,iproc-rng200";
+			reg = <0x300 0x28>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		uart0: serial@600 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0x600 0x20>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&periph_clk>;
+			clock-names = "refclk";
+			status = "disabled";
+		};
+
+		leds: led-controller@700 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm63138-leds";
+			reg = <0x700 0xdc>;
+			status = "disabled";
+		};
+
+		hsspi: spi@1000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm63148-hsspi", "brcm,bcmbca-hsspi-v1.0";
+			reg = <0x1000 0x600>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsspi_pll &hsspi_pll>;
+			clock-names = "hsspi", "pll";
+			num-cs = <8>;
+			status = "disabled";
+		};
+
+		nand_controller: nand-controller@2000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,nand-bcm63138", "brcm,brcmnand-v7.1", "brcm,brcmnand";
+			reg = <0x2000 0x600>, <0xf0 0x10>;
+			reg-names = "nand", "nand-int-base";
+			status = "disabled";
+
+			nandcs: nand@0 {
+				compatible = "brcm,nandcs";
+				reg = <0>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm63178.dtsi b/arch/arm/boot/dts/broadcom/bcm63178.dtsi
new file mode 100644
index 000000000000..430750b3030f
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm63178.dtsi
@@ -0,0 +1,267 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm63178", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CA7_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x2>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&CA7_0>, <&CA7_1>,
+			<&CA7_2>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+
+		uart_clk: uart-clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clocks = <&periph_clk>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+
+		hsspi_pll: hsspi-pll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_HIGH)>;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xff800000 0x800000>;
+
+		watchdog@480 {
+			compatible = "brcm,bcm6345-wdt";
+			reg = <0x480 0x10>;
+		};
+
+		/* GPIOs 0 .. 31 */
+		gpio0: gpio@500 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x500 0x04>, <0x520 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 32 .. 63 */
+		gpio1: gpio@504 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x504 0x04>, <0x524 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 64 .. 95 */
+		gpio2: gpio@508 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x508 0x04>, <0x528 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 96 .. 127 */
+		gpio3: gpio@50c {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x50c 0x04>, <0x52c 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 128 .. 159 */
+		gpio4: gpio@510 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x510 0x04>, <0x530 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 160 .. 191 */
+		gpio5: gpio@514 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x514 0x04>, <0x534 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 192 .. 223 */
+		gpio6: gpio@518 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x518 0x04>, <0x538 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 224 .. 255 */
+		gpio7: gpio@51c {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x51c 0x04>, <0x53c 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		rng@b80 {
+			compatible = "brcm,iproc-rng200";
+			reg = <0xb80 0x28>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		hsspi: spi@1000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm63178-hsspi", "brcm,bcmbca-hsspi-v1.0";
+			reg = <0x1000 0x600>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsspi_pll &hsspi_pll>;
+			clock-names = "hsspi", "pll";
+			num-cs = <8>;
+			status = "disabled";
+		};
+
+		nand_controller: nand-controller@1800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,nand-bcm63138", "brcm,brcmnand-v7.1", "brcm,brcmnand";
+			reg = <0x1800 0x600>, <0x2000 0x10>;
+			reg-names = "nand", "nand-int-base";
+			status = "disabled";
+
+			nandcs: nand@0 {
+				compatible = "brcm,nandcs";
+				reg = <0>;
+			};
+		};
+
+		leds: led-controller@3000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm63138-leds";
+			reg = <0x3000 0xdc>;
+			status = "disabled";
+		};
+
+		pl081_dma: dma-controller@11000 {
+			compatible = "arm,pl081", "arm,primecell";
+			// The magic B105F00D info is missing
+			arm,primecell-periphid = <0x00041081>;
+			reg = <0x11000 0x1000>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+			memcpy-burst-size = <256>;
+			memcpy-bus-width = <32>;
+			clocks = <&periph_clk>;
+			clock-names = "apb_pclk";
+			#dma-cells = <2>;
+		};
+
+		uart0: serial@12000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x12000 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm6756.dtsi b/arch/arm/boot/dts/broadcom/bcm6756.dtsi
new file mode 100644
index 000000000000..6433f8fa5eff
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm6756.dtsi
@@ -0,0 +1,165 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm6756", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CA7_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x2>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x3>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&CA7_0>, <&CA7_1>,
+			<&CA7_2>, <&CA7_3>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+
+		uart_clk: uart-clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clocks = <&periph_clk>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+
+		hsspi_pll: hsspi-pll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xff800000 0x800000>;
+
+		hsspi: spi@1000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6756-hsspi", "brcm,bcmbca-hsspi-v1.1";
+			reg = <0x1000 0x600>, <0x2610 0x4>;
+			reg-names = "hsspi", "spim-ctrl";
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsspi_pll &hsspi_pll>;
+			clock-names = "hsspi", "pll";
+			num-cs = <8>;
+			status = "disabled";
+		};
+
+		nand_controller: nand-controller@1800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,nand-bcm63138", "brcm,brcmnand-v7.1", "brcm,brcmnand";
+			reg = <0x1800 0x600>, <0x2000 0x10>;
+			reg-names = "nand", "nand-int-base";
+			status = "disabled";
+
+			nandcs: nand@0 {
+				compatible = "brcm,nandcs";
+				reg = <0>;
+			};
+		};
+
+		uart0: serial@12000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x12000 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm6846-genexis-xg6846b.dts b/arch/arm/boot/dts/broadcom/bcm6846-genexis-xg6846b.dts
new file mode 100644
index 000000000000..a3616fb7b3a8
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm6846-genexis-xg6846b.dts
@@ -0,0 +1,244 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2024 Linus Walleij <linus.walleij@linaro.org>
+ */
+
+/dts-v1/;
+
+#include "bcm6846.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Genexis XG6846B Ethernet layer 2/3 router";
+	compatible = "genexis,xg6846b", "brcm,bcm6846", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	/* Micron D9PTK 256 MB RAM */
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x10000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		secondary-boot@0 {
+			no-map;
+			reg = <0x00000000 0x00008000>;
+		};
+		pmc3-firmware@8000 {
+			no-map;
+			reg = <0x00008000 0x00100000>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys-polled";
+		poll-interval = <20000>;
+
+		/* Called "canyon rescue button" in the vendor DTB */
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio0 41 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&gpio2 {
+	status = "okay";
+	/* Totally 79 GPIOs are available */
+	ngpios = <15>;
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&leds {
+	status = "okay";
+	brcm,serial-shift-bits = <16>;
+
+	led@0 {
+		reg = <0>;
+		active-low;
+		function = "ext";
+		color = <LED_COLOR_ID_GREEN>;
+	};
+
+	led@1 {
+		reg = <1>;
+		active-low;
+		function = "ext";
+		color = <LED_COLOR_ID_AMBER>;
+	};
+
+	led@3 {
+		reg = <3>;
+		active-low;
+		function = LED_FUNCTION_WAN;
+		color = <LED_COLOR_ID_AMBER>;
+	};
+
+	led@4 {
+		reg = <4>;
+		active-low;
+		function = LED_FUNCTION_WAN;
+		color = <LED_COLOR_ID_GREEN>;
+	};
+
+	led@5 {
+		reg = <5>;
+		active-low;
+		function = LED_FUNCTION_POWER;
+		color = <LED_COLOR_ID_GREEN>;
+	};
+
+	led@6 {
+		reg = <6>;
+		active-low;
+		function = LED_FUNCTION_POWER;
+		color = <LED_COLOR_ID_RED>;
+	};
+
+	led@15 {
+		reg = <15>;
+		active-low;
+		function = LED_FUNCTION_USB;
+		color = <LED_COLOR_ID_GREEN>;
+	};
+
+	led@7 {
+		/* Activity 03 */
+		reg = <7>;
+		active-low;
+		function = "lan1";
+		color = <LED_COLOR_ID_AMBER>;
+	};
+
+	led@8 {
+		/* Activity 04 */
+		reg = <8>;
+		active-low;
+		function = "lan1";
+		color = <LED_COLOR_ID_GREEN>;
+	};
+
+	led@9 {
+		/* Activity 03 */
+		reg = <9>;
+		active-low;
+		function = "lan2";
+		color = <LED_COLOR_ID_AMBER>;
+	};
+
+	led@10 {
+		/* Activity 04 */
+		reg = <10>;
+		active-low;
+		function = "lan2";
+		color = <LED_COLOR_ID_GREEN>;
+	};
+
+	led@11 {
+		/* Activity 03 */
+		reg = <11>;
+		active-low;
+		function = "lan3";
+		color = <LED_COLOR_ID_AMBER>;
+	};
+
+	led@12 {
+		/* Activity 04 */
+		reg = <12>;
+		active-low;
+		function = "lan3";
+		color = <LED_COLOR_ID_GREEN>;
+	};
+
+	led@13 {
+		/* Activity 03 */
+		reg = <13>;
+		active-low;
+		function = "lan4";
+		color = <LED_COLOR_ID_AMBER>;
+	};
+
+	led@14 {
+		/* Activity 04 */
+		reg = <14>;
+		active-low;
+		function = "lan4";
+		color = <LED_COLOR_ID_GREEN>;
+	};
+};
+
+&hsspi {
+	status = "okay";
+};
+
+&nand_controller {
+	brcm,wp-not-connected;
+	status = "okay";
+};
+
+&nandcs {
+	nand-on-flash-bbt;
+	brcm,nand-ecc-use-strap;
+
+	/* Winbond W29N02GV, 256MB with 128KB erase blocks */
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		loader@0 {
+			label = "loader";
+			reg = <0x00000000 0x00400000>;
+		};
+		image@400000 {
+			label = "image";
+			reg = <0x00400000 0x0fb00000>;
+		};
+		/* 0x00ff0000-0x00ffffff: bad block list */
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+	phy2: ethernet-phy@2 {
+		reg = <2>;
+	};
+	phy3: ethernet-phy@3 {
+		reg = <3>;
+	};
+	phy4: ethernet-phy@4 {
+		reg = <4>;
+	};
+	phy21: ethernet-phy@21 {
+		reg = <21>;
+	};
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm6846.dtsi b/arch/arm/boot/dts/broadcom/bcm6846.dtsi
new file mode 100644
index 000000000000..f5591a45d2e4
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm6846.dtsi
@@ -0,0 +1,258 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm6846", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CA7_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&CA7_0>, <&CA7_1>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+
+		hsspi_pll: hsspi-pll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <400000000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xff800000 0x800000>;
+
+		watchdog@480 {
+			compatible = "brcm,bcm6345-wdt";
+			reg = <0x480 0x10>;
+		};
+
+		/* GPIOs 0 .. 31 */
+		gpio0: gpio@500 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x500 0x04>, <0x520 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 32 .. 63 */
+		gpio1: gpio@504 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x504 0x04>, <0x524 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 64 .. 95 */
+		gpio2: gpio@508 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x508 0x04>, <0x528 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 96 .. 127 */
+		gpio3: gpio@50c {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x50c 0x04>, <0x52c 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 128 .. 159 */
+		gpio4: gpio@510 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x510 0x04>, <0x530 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 160 .. 191 */
+		gpio5: gpio@514 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x514 0x04>, <0x534 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 192 .. 223 */
+		gpio6: gpio@518 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x518 0x04>, <0x538 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 224 .. 255 */
+		gpio7: gpio@51c {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x51c 0x04>, <0x53c 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		uart0: serial@640 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0x640 0x1b>;
+			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&periph_clk>;
+			clock-names = "refclk";
+			status = "disabled";
+		};
+
+		rng@b80 {
+			compatible = "brcm,iproc-rng200";
+			reg = <0xb80 0x28>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		leds: led-controller@800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm63138-leds";
+			reg = <0x800 0xdc>;
+			status = "disabled";
+		};
+
+		hsspi: spi@1000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6846-hsspi", "brcm,bcmbca-hsspi-v1.0";
+			reg = <0x1000 0x600>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsspi_pll &hsspi_pll>;
+			clock-names = "hsspi", "pll";
+			num-cs = <8>;
+			status = "disabled";
+		};
+
+		nand_controller: nand-controller@1800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,nand-bcm63138", "brcm,brcmnand-v7.1", "brcm,brcmnand";
+			reg = <0x1800 0x600>, <0x2000 0x10>;
+			reg-names = "nand", "nand-int-base";
+			status = "disabled";
+
+			nandcs: nand@0 {
+				compatible = "brcm,nandcs";
+				reg = <0>;
+			};
+		};
+
+		mdio: mdio@2060 {
+			compatible = "brcm,bcm6846-mdio";
+			reg = <0x02060 0x10>, <0x5a068 0x4>;
+			reg-names = "mdio", "mdio_indir_rw";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		pl081_dma: dma-controller@59000 {
+			compatible = "arm,pl081", "arm,primecell";
+			// The magic B105F00D info is missing
+			arm,primecell-periphid = <0x00041081>;
+			reg = <0x59000 0x1000>;
+			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+			memcpy-burst-size = <256>;
+			memcpy-bus-width = <32>;
+			clocks = <&periph_clk>;
+			clock-names = "apb_pclk";
+			#dma-cells = <2>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm6855.dtsi b/arch/arm/boot/dts/broadcom/bcm6855.dtsi
new file mode 100644
index 000000000000..a88c3f0fbcb0
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm6855.dtsi
@@ -0,0 +1,282 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm6855", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CA7_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x2>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&CA7_0>, <&CA7_1>, <&CA7_2>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+
+		uart_clk: uart-clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clocks = <&periph_clk>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+
+		hsspi_pll: hsspi-pll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_HIGH)>;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xff800000 0x800000>;
+
+		watchdog@480 {
+			compatible = "brcm,bcm6345-wdt";
+			reg = <0x480 0x10>;
+		};
+
+		watchdog@4c0 {
+			compatible = "brcm,bcm6345-wdt";
+			reg = <0x4c0 0x10>;
+			status = "disabled";
+		};
+
+		/* GPIOs 0 .. 31 */
+		gpio0: gpio@500 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x500 0x04>, <0x520 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 32 .. 63 */
+		gpio1: gpio@504 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x504 0x04>, <0x524 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 64 .. 95 */
+		gpio2: gpio@508 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x508 0x04>, <0x528 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 96 .. 127 */
+		gpio3: gpio@50c {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x50c 0x04>, <0x52c 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 128 .. 159 */
+		gpio4: gpio@510 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x510 0x04>, <0x530 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 160 .. 191 */
+		gpio5: gpio@514 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x514 0x04>, <0x534 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 192 .. 223 */
+		gpio6: gpio@518 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x518 0x04>, <0x538 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 224 .. 255 */
+		gpio7: gpio@51c {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x51c 0x04>, <0x53c 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		rng@b80 {
+			compatible = "brcm,iproc-rng200";
+			reg = <0xb80 0x28>;
+			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		hsspi: spi@1000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6855-hsspi", "brcm,bcmbca-hsspi-v1.1";
+			reg = <0x1000 0x600>, <0x2610 0x4>;
+			reg-names = "hsspi", "spim-ctrl";
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsspi_pll &hsspi_pll>;
+			clock-names = "hsspi", "pll";
+			num-cs = <8>;
+			status = "disabled";
+		};
+
+		nand_controller: nand-controller@1800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,nand-bcm63138", "brcm,brcmnand-v7.1", "brcm,brcmnand";
+			reg = <0x1800 0x600>, <0x2000 0x10>;
+			reg-names = "nand", "nand-int-base";
+			status = "disabled";
+
+			nandcs: nand@0 {
+				compatible = "brcm,nandcs";
+				reg = <0>;
+			};
+		};
+
+		leds: led-controller@3000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm63138-leds";
+			reg = <0x3000 0xdc>;
+			status = "disabled";
+		};
+
+		pl081_dma: dma-controller@11000 {
+			compatible = "arm,pl081", "arm,primecell";
+			// The magic B105F00D info is missing
+			arm,primecell-periphid = <0x00041081>;
+			reg = <0x11000 0x1000>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+			memcpy-burst-size = <256>;
+			memcpy-bus-width = <32>;
+			clocks = <&periph_clk>;
+			clock-names = "apb_pclk";
+			#dma-cells = <2>;
+		};
+
+		uart0: serial@12000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x12000 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		uart1: serial@13000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x13000 0x1000>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm6878.dtsi b/arch/arm/boot/dts/broadcom/bcm6878.dtsi
new file mode 100644
index 000000000000..dd837bf69390
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm6878.dtsi
@@ -0,0 +1,264 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm6878", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CA7_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&CA7_0>, <&CA7_1>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+
+		uart_clk: uart-clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clocks = <&periph_clk>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+
+		hsspi_pll: hsspi-pll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) |
+					IRQ_TYPE_LEVEL_HIGH)>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xff800000 0x800000>;
+
+		watchdog@480 {
+			compatible = "brcm,bcm6345-wdt";
+			reg = <0x480 0x10>;
+		};
+
+		watchdog@4c0 {
+			compatible = "brcm,bcm6345-wdt";
+			reg = <0x4c0 0x10>;
+			status = "disabled";
+		};
+
+		/* GPIOs 0 .. 31 */
+		gpio0: gpio@500 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x500 0x04>, <0x520 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 32 .. 63 */
+		gpio1: gpio@504 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x504 0x04>, <0x524 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 64 .. 95 */
+		gpio2: gpio@508 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x508 0x04>, <0x528 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 96 .. 127 */
+		gpio3: gpio@50c {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x50c 0x04>, <0x52c 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 128 .. 159 */
+		gpio4: gpio@510 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x510 0x04>, <0x530 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 160 .. 191 */
+		gpio5: gpio@514 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x514 0x04>, <0x534 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 192 .. 223 */
+		gpio6: gpio@518 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x518 0x04>, <0x538 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 224 .. 255 */
+		gpio7: gpio@51c {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x51c 0x04>, <0x53c 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		rng@b80 {
+			compatible = "brcm,iproc-rng200";
+			reg = <0xb80 0x28>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		leds: led-controller@700 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm63138-leds";
+			reg = <0x700 0xdc>;
+			status = "disabled";
+		};
+
+		hsspi: spi@1000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm6878-hsspi", "brcm,bcmbca-hsspi-v1.0";
+			reg = <0x1000 0x600>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsspi_pll &hsspi_pll>;
+			clock-names = "hsspi", "pll";
+			num-cs = <8>;
+			status = "disabled";
+		};
+
+		nand_controller: nand-controller@1800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,nand-bcm63138", "brcm,brcmnand-v7.1", "brcm,brcmnand";
+			reg = <0x1800 0x600>, <0x2000 0x10>;
+			reg-names = "nand", "nand-int-base";
+			status = "disabled";
+
+			nandcs: nand@0 {
+				compatible = "brcm,nandcs";
+				reg = <0>;
+			};
+		};
+
+		pl081_dma: dma-controller@11000 {
+			compatible = "arm,pl081", "arm,primecell";
+			// The magic B105F00D info is missing
+			arm,primecell-periphid = <0x00041081>;
+			reg = <0x11000 0x1000>;
+			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			memcpy-burst-size = <256>;
+			memcpy-bus-width = <32>;
+			clocks = <&periph_clk>;
+			clock-names = "apb_pclk";
+			#dma-cells = <2>;
+		};
+
+		uart0: serial@12000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x12000 0x1000>;
+			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm7445-bcm97445svmb.dts b/arch/arm/boot/dts/broadcom/bcm7445-bcm97445svmb.dts
index f92d2cf85972..f92d2cf85972 100644
--- a/arch/arm/boot/dts/bcm7445-bcm97445svmb.dts
+++ b/arch/arm/boot/dts/broadcom/bcm7445-bcm97445svmb.dts
diff --git a/arch/arm/boot/dts/bcm7445.dtsi b/arch/arm/boot/dts/broadcom/bcm7445.dtsi
index 5ac2042515b8..c6307c7437e3 100644
--- a/arch/arm/boot/dts/bcm7445.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm7445.dtsi
@@ -237,7 +237,8 @@
 			ranges = <0x0 0x0 0x80000>;
 
 			memc-ddr@2000 {
-				compatible = "brcm,brcmstb-memc-ddr";
+				compatible = "brcm,brcmstb-memc-ddr-rev-b.1.x",
+					     "brcm,brcmstb-memc-ddr";
 				reg = <0x2000 0x800>;
 			};
 
@@ -259,7 +260,8 @@
 			ranges = <0x0 0x80000 0x80000>;
 
 			memc-ddr@2000 {
-				compatible = "brcm,brcmstb-memc-ddr";
+				compatible = "brcm,brcmstb-memc-ddr-rev-b.1.x",
+					     "brcm,brcmstb-memc-ddr";
 				reg = <0x2000 0x800>;
 			};
 
@@ -281,7 +283,8 @@
 			ranges = <0x0 0x100000 0x80000>;
 
 			memc-ddr@2000 {
-				compatible = "brcm,brcmstb-memc-ddr";
+				compatible = "brcm,brcmstb-memc-ddr-rev-b.1.x",
+					     "brcm,brcmstb-memc-ddr";
 				reg = <0x2000 0x800>;
 			};
 
diff --git a/arch/arm/boot/dts/bcm911360_entphn.dts b/arch/arm/boot/dts/broadcom/bcm911360_entphn.dts
index a76c74b44bba..363009e747b3 100644
--- a/arch/arm/boot/dts/bcm911360_entphn.dts
+++ b/arch/arm/boot/dts/broadcom/bcm911360_entphn.dts
@@ -47,10 +47,10 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		hook {
+		button-hook {
 			label = "HOOK";
 			linux,code = <KEY_O>;
 			gpios = <&gpio_asiu 48 0>;
diff --git a/arch/arm/boot/dts/bcm911360k.dts b/arch/arm/boot/dts/broadcom/bcm911360k.dts
index 091c73a46e08..091c73a46e08 100644
--- a/arch/arm/boot/dts/bcm911360k.dts
+++ b/arch/arm/boot/dts/broadcom/bcm911360k.dts
diff --git a/arch/arm/boot/dts/bcm94708.dts b/arch/arm/boot/dts/broadcom/bcm94708.dts
index d9eb2040b963..d9eb2040b963 100644
--- a/arch/arm/boot/dts/bcm94708.dts
+++ b/arch/arm/boot/dts/broadcom/bcm94708.dts
diff --git a/arch/arm/boot/dts/bcm94709.dts b/arch/arm/boot/dts/broadcom/bcm94709.dts
index 618c812eef73..618c812eef73 100644
--- a/arch/arm/boot/dts/bcm94709.dts
+++ b/arch/arm/boot/dts/broadcom/bcm94709.dts
diff --git a/arch/arm/boot/dts/bcm947189acdbmr.dts b/arch/arm/boot/dts/broadcom/bcm947189acdbmr.dts
index b0b8c774a37f..0b8727ae6f16 100644
--- a/arch/arm/boot/dts/bcm947189acdbmr.dts
+++ b/arch/arm/boot/dts/broadcom/bcm947189acdbmr.dts
@@ -25,17 +25,17 @@
 	leds {
 		compatible = "gpio-leds";
 
-		wps {
+		led-wps {
 			label = "bcm53xx:blue:wps";
 			gpios = <&chipcommon 10 GPIO_ACTIVE_HIGH>;
 		};
 
-		5ghz {
+		led-5ghz {
 			label = "bcm53xx:blue:5ghz";
 			gpios = <&chipcommon 11 GPIO_ACTIVE_HIGH>;
 		};
 
-		2ghz {
+		led-2ghz {
 			label = "bcm53xx:blue:2ghz";
 			gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
 		};
@@ -44,13 +44,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_HIGH>;
 		};
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 9 GPIO_ACTIVE_LOW>;
@@ -60,9 +60,9 @@
 	spi {
 		compatible = "spi-gpio";
 		num-chipselects = <1>;
-		gpio-sck = <&chipcommon 21 0>;
-		gpio-miso = <&chipcommon 22 0>;
-		gpio-mosi = <&chipcommon 23 0>;
+		sck-gpios = <&chipcommon 21 0>;
+		miso-gpios = <&chipcommon 22 0>;
+		mosi-gpios = <&chipcommon 23 0>;
 		cs-gpios = <&chipcommon 24 0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
diff --git a/arch/arm/boot/dts/broadcom/bcm947622.dts b/arch/arm/boot/dts/broadcom/bcm947622.dts
new file mode 100644
index 000000000000..6241485408d3
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm947622.dts
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm47622.dtsi"
+
+/ {
+	model = "Broadcom BCM947622 Reference Board";
+	compatible = "brcm,bcm947622", "brcm,bcm47622", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&hsspi {
+	status = "okay";
+};
+
+&nand_controller {
+	brcm,wp-not-connected;
+	status = "okay";
+};
+
+&nandcs {
+	nand-on-flash-bbt;
+	brcm,nand-ecc-use-strap;
+};
diff --git a/arch/arm/boot/dts/bcm953012er.dts b/arch/arm/boot/dts/broadcom/bcm953012er.dts
index 52feca0fb906..d939ec9f4a9e 100644
--- a/arch/arm/boot/dts/bcm953012er.dts
+++ b/arch/arm/boot/dts/broadcom/bcm953012er.dts
@@ -37,7 +37,7 @@
 
 / {
 	model = "NorthStar Enterprise Router (BCM953012ER)";
-	compatible = "brcm,bcm953012er", "brcm,brcm53012", "brcm,bcm4708";
+	compatible = "brcm,bcm953012er", "brcm,bcm53012", "brcm,bcm4708";
 
 	memory@0 {
 		device_type = "memory";
@@ -47,13 +47,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
@@ -84,6 +84,14 @@
 			label = "cpu";
 			ethernet = <&gmac0>;
 		};
+
+		port@7 {
+			status = "disabled";
+		};
+
+		port@8 {
+			status = "disabled";
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/bcm953012hr.dts b/arch/arm/boot/dts/broadcom/bcm953012hr.dts
index 9140be7ec053..b728cd54715e 100644
--- a/arch/arm/boot/dts/bcm953012hr.dts
+++ b/arch/arm/boot/dts/broadcom/bcm953012hr.dts
@@ -37,7 +37,7 @@
 
 / {
 	model = "NorthStar HR (BCM953012HR)";
-	compatible = "brcm,bcm953012hr", "brcm,brcm53012", "brcm,bcm4708";
+	compatible = "brcm,bcm953012hr", "brcm,bcm53012", "brcm,bcm4708";
 
 	aliases {
 		ethernet0 = &gmac0;
@@ -74,7 +74,6 @@
 &spi_nor {
 	status = "okay";
 	spi-max-frequency = <62500000>;
-	m25p,default-addr-width = <3>;
 
 	#address-cells = <1>;
 	#size-cells = <1>;
diff --git a/arch/arm/boot/dts/bcm953012k.dts b/arch/arm/boot/dts/broadcom/bcm953012k.dts
index de40bd59a5fa..27c0992f1855 100644
--- a/arch/arm/boot/dts/bcm953012k.dts
+++ b/arch/arm/boot/dts/broadcom/bcm953012k.dts
@@ -36,7 +36,7 @@
 
 / {
 	model = "NorthStar SVK (BCM953012K)";
-	compatible = "brcm,bcm953012k", "brcm,brcm53012", "brcm,bcm4708";
+	compatible = "brcm,bcm953012k", "brcm,bcm53012", "brcm,bcm4708";
 
 	aliases {
 		serial0 = &uart0;
@@ -84,7 +84,6 @@
 &spi_nor {
 	status = "okay";
 	spi-max-frequency = <62500000>;
-	m25p,default-addr-width = <3>;
 
 	#address-cells = <1>;
 	#size-cells = <1>;
diff --git a/arch/arm/boot/dts/bcm958300k.dts b/arch/arm/boot/dts/broadcom/bcm958300k.dts
index dda3e11b711f..dda3e11b711f 100644
--- a/arch/arm/boot/dts/bcm958300k.dts
+++ b/arch/arm/boot/dts/broadcom/bcm958300k.dts
diff --git a/arch/arm/boot/dts/bcm958305k.dts b/arch/arm/boot/dts/broadcom/bcm958305k.dts
index ea3c6b88b313..ea3c6b88b313 100644
--- a/arch/arm/boot/dts/bcm958305k.dts
+++ b/arch/arm/boot/dts/broadcom/bcm958305k.dts
diff --git a/arch/arm/boot/dts/bcm958522er.dts b/arch/arm/boot/dts/broadcom/bcm958522er.dts
index 60376b62cd5f..2f20f86bd31c 100644
--- a/arch/arm/boot/dts/bcm958522er.dts
+++ b/arch/arm/boot/dts/broadcom/bcm958522er.dts
@@ -135,8 +135,7 @@
 
 &qspi {
 	status = "okay";
-	bspi-sel = <0>;
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p80";
diff --git a/arch/arm/boot/dts/bcm958525er.dts b/arch/arm/boot/dts/broadcom/bcm958525er.dts
index 8eeb319f5b54..980c03f74a19 100644
--- a/arch/arm/boot/dts/bcm958525er.dts
+++ b/arch/arm/boot/dts/broadcom/bcm958525er.dts
@@ -135,8 +135,7 @@
 
 &qspi {
 	status = "okay";
-	bspi-sel = <0>;
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p80";
diff --git a/arch/arm/boot/dts/bcm958525xmc.dts b/arch/arm/boot/dts/broadcom/bcm958525xmc.dts
index dc86d5a91292..440bb2d617f2 100644
--- a/arch/arm/boot/dts/bcm958525xmc.dts
+++ b/arch/arm/boot/dts/broadcom/bcm958525xmc.dts
@@ -151,8 +151,7 @@
 
 &qspi {
 	status = "okay";
-	bspi-sel = <0>;
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p80";
diff --git a/arch/arm/boot/dts/bcm958622hr.dts b/arch/arm/boot/dts/broadcom/bcm958622hr.dts
index c457e53d886e..116f3a7c3bc6 100644
--- a/arch/arm/boot/dts/bcm958622hr.dts
+++ b/arch/arm/boot/dts/broadcom/bcm958622hr.dts
@@ -139,8 +139,7 @@
 
 &qspi {
 	status = "okay";
-	bspi-sel = <0>;
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p80";
diff --git a/arch/arm/boot/dts/bcm958623hr.dts b/arch/arm/boot/dts/broadcom/bcm958623hr.dts
index c06871915a1c..fc6ab73ecf56 100644
--- a/arch/arm/boot/dts/bcm958623hr.dts
+++ b/arch/arm/boot/dts/broadcom/bcm958623hr.dts
@@ -143,8 +143,7 @@
 
 &qspi {
 	status = "okay";
-	bspi-sel = <0>;
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p80";
diff --git a/arch/arm/boot/dts/bcm958625-meraki-alamo.dtsi b/arch/arm/boot/dts/broadcom/bcm958625-meraki-alamo.dtsi
index 58b7d9fc7574..c54451dde6dd 100644
--- a/arch/arm/boot/dts/bcm958625-meraki-alamo.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm958625-meraki-alamo.dtsi
@@ -13,7 +13,7 @@
 		autorepeat;
 		poll-interval = <20>;
 
-		reset {
+		button-reset {
 			label = "reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpioa 8 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm958625-meraki-kingpin.dtsi b/arch/arm/boot/dts/broadcom/bcm958625-meraki-kingpin.dtsi
index 576cfc52567b..1830844c8404 100644
--- a/arch/arm/boot/dts/bcm958625-meraki-kingpin.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm958625-meraki-kingpin.dtsi
@@ -14,7 +14,7 @@
 		autorepeat;
 		poll-interval = <20>;
 
-		reset {
+		button-reset {
 			label = "reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpioa 6 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm958625-meraki-mx64-a0.dts b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx64-a0.dts
index 9944566c1195..9944566c1195 100644
--- a/arch/arm/boot/dts/bcm958625-meraki-mx64-a0.dts
+++ b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx64-a0.dts
diff --git a/arch/arm/boot/dts/bcm958625-meraki-mx64.dts b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx64.dts
index 06939438e874..06939438e874 100644
--- a/arch/arm/boot/dts/bcm958625-meraki-mx64.dts
+++ b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx64.dts
diff --git a/arch/arm/boot/dts/bcm958625-meraki-mx64w-a0.dts b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx64w-a0.dts
index 112fddb1eed8..112fddb1eed8 100644
--- a/arch/arm/boot/dts/bcm958625-meraki-mx64w-a0.dts
+++ b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx64w-a0.dts
diff --git a/arch/arm/boot/dts/bcm958625-meraki-mx64w.dts b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx64w.dts
index de2e367c3e78..de2e367c3e78 100644
--- a/arch/arm/boot/dts/bcm958625-meraki-mx64w.dts
+++ b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx64w.dts
diff --git a/arch/arm/boot/dts/bcm958625-meraki-mx65.dts b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx65.dts
index d1b684dcdbfa..d1b684dcdbfa 100644
--- a/arch/arm/boot/dts/bcm958625-meraki-mx65.dts
+++ b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx65.dts
diff --git a/arch/arm/boot/dts/bcm958625-meraki-mx65w.dts b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx65w.dts
index a2165aba3676..a2165aba3676 100644
--- a/arch/arm/boot/dts/bcm958625-meraki-mx65w.dts
+++ b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx65w.dts
diff --git a/arch/arm/boot/dts/bcm958625-meraki-mx6x-common.dtsi b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx6x-common.dtsi
index b0854d881ac6..7e71aecb7251 100644
--- a/arch/arm/boot/dts/bcm958625-meraki-mx6x-common.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm958625-meraki-mx6x-common.dtsi
@@ -17,21 +17,21 @@
 		led-1 {
 			function = LED_FUNCTION_INDICATOR;
 			color = <LED_COLOR_ID_RED>;
-			pwms = <&pwm 1 50000>;
+			pwms = <&pwm 1 50000 0>;
 			max-brightness = <255>;
 		};
 
 		led-2 {
 			function = LED_FUNCTION_POWER;
 			color = <LED_COLOR_ID_GREEN>;
-			pwms = <&pwm 2 50000>;
+			pwms = <&pwm 2 50000 0>;
 			max-brightness = <255>;
 		};
 
 		led-3 {
 			function = LED_FUNCTION_INDICATOR;
 			color = <LED_COLOR_ID_BLUE>;
-			pwms = <&pwm 3 50000>;
+			pwms = <&pwm 3 50000 0>;
 			max-brightness = <255>;
 		};
 	};
@@ -55,11 +55,15 @@
 		reg = <0x50>;
 		pagesize = <32>;
 		read-only;
-		#address-cells = <1>;
-		#size-cells = <1>;
 
-		mac_address: mac-address@66 {
-			reg = <0x66 0x6>;
+		nvmem-layout {
+			compatible = "fixed-layout";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			mac_address: mac-address@66 {
+				reg = <0x66 0x6>;
+			};
 		};
 	};
 };
@@ -128,7 +132,6 @@
 
 &pwm {
 	status = "okay";
-	#pwm-cells = <2>;
 };
 
 &uart0 {
diff --git a/arch/arm/boot/dts/bcm958625hr.dts b/arch/arm/boot/dts/broadcom/bcm958625hr.dts
index b22fc6624ae4..a9b6aa04d573 100644
--- a/arch/arm/boot/dts/bcm958625hr.dts
+++ b/arch/arm/boot/dts/broadcom/bcm958625hr.dts
@@ -150,8 +150,7 @@
 
 &qspi {
 	status = "okay";
-	bspi-sel = <0>;
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p80";
diff --git a/arch/arm/boot/dts/bcm958625k.dts b/arch/arm/boot/dts/broadcom/bcm958625k.dts
index 0183f8965a74..7996116fc923 100644
--- a/arch/arm/boot/dts/bcm958625k.dts
+++ b/arch/arm/boot/dts/broadcom/bcm958625k.dts
@@ -154,8 +154,7 @@
 
 &qspi {
 	status = "okay";
-	bspi-sel = <0>;
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p80";
diff --git a/arch/arm/boot/dts/broadcom/bcm963138.dts b/arch/arm/boot/dts/broadcom/bcm963138.dts
new file mode 100644
index 000000000000..7fd87e05ec20
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm963138.dts
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm63138.dtsi"
+
+/ {
+	model = "Broadcom BCM963138 Reference Board";
+	compatible = "brcm,bcm963138", "brcm,bcm63138", "brcm,bcmbca";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &serial0;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&serial0 {
+	status = "okay";
+};
+
+&hsspi {
+	status = "okay";
+};
+
+&nand_controller {
+	brcm,wp-not-connected;
+	status = "okay";
+};
+
+&nandcs {
+	nand-on-flash-bbt;
+	brcm,nand-ecc-use-strap;
+};
diff --git a/arch/arm/boot/dts/bcm963138dvt.dts b/arch/arm/boot/dts/broadcom/bcm963138dvt.dts
index df5c8ab90627..f60d09908ab9 100644
--- a/arch/arm/boot/dts/bcm963138dvt.dts
+++ b/arch/arm/boot/dts/broadcom/bcm963138dvt.dts
@@ -8,7 +8,7 @@
 #include "bcm63138.dtsi"
 
 / {
-	compatible = "brcm,BCM963138DVT", "brcm,bcm63138";
+	compatible = "brcm,BCM963138DVT", "brcm,bcm63138", "brcm,bcmbca";
 	model = "Broadcom BCM963138DVT";
 
 	chosen {
@@ -32,15 +32,15 @@
 };
 
 &nand_controller {
+	brcm,wp-not-connected;
 	status = "okay";
+};
 
-	nand@0 {
-		compatible = "brcm,nandcs";
-		reg = <0>;
-		nand-ecc-strength = <4>;
-		nand-ecc-step-size = <512>;
-		brcm,nand-oob-sectors-size = <16>;
-	};
+&nandcs {
+	nand-ecc-strength = <4>;
+	nand-ecc-step-size = <512>;
+	brcm,nand-oob-sector-size = <16>;
+	nand-on-flash-bbt;
 };
 
 &ahci {
@@ -50,3 +50,7 @@
 &sata_phy {
 	status = "okay";
 };
+
+&hsspi {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm963148.dts b/arch/arm/boot/dts/broadcom/bcm963148.dts
new file mode 100644
index 000000000000..44bca063a327
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm963148.dts
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm63148.dtsi"
+
+/ {
+	model = "Broadcom BCM963148 Reference Board";
+	compatible = "brcm,bcm963148", "brcm,bcm63148", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&hsspi {
+	status = "okay";
+};
+
+&nand_controller {
+	brcm,wp-not-connected;
+	status = "okay";
+};
+
+&nandcs {
+	nand-on-flash-bbt;
+	brcm,nand-ecc-use-strap;
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm963178.dts b/arch/arm/boot/dts/broadcom/bcm963178.dts
new file mode 100644
index 000000000000..098a222cd71a
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm963178.dts
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm63178.dtsi"
+
+/ {
+	model = "Broadcom BCM963178 Reference Board";
+	compatible = "brcm,bcm963178", "brcm,bcm63178", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&hsspi {
+	status = "okay";
+};
+
+&nand_controller {
+	brcm,wp-not-connected;
+	status = "okay";
+};
+
+&nandcs {
+	nand-on-flash-bbt;
+	brcm,nand-ecc-use-strap;
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm96756.dts b/arch/arm/boot/dts/broadcom/bcm96756.dts
new file mode 100644
index 000000000000..402038d3cd0c
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm96756.dts
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm6756.dtsi"
+
+/ {
+	model = "Broadcom BCM96756 Reference Board";
+	compatible = "brcm,bcm96756", "brcm,bcm6756", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&hsspi {
+	status = "okay";
+};
+
+&nand_controller {
+	brcm,wp-not-connected;
+	status = "okay";
+};
+
+&nandcs {
+	nand-on-flash-bbt;
+	brcm,nand-ecc-use-strap;
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm96846.dts b/arch/arm/boot/dts/broadcom/bcm96846.dts
new file mode 100644
index 000000000000..943896afb7cc
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm96846.dts
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm6846.dtsi"
+
+/ {
+	model = "Broadcom BCM96846 Reference Board";
+	compatible = "brcm,bcm96846", "brcm,bcm6846", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&hsspi {
+	status = "okay";
+};
+
+&nand_controller {
+	brcm,wp-not-connected;
+	status = "okay";
+};
+
+&nandcs {
+	nand-on-flash-bbt;
+	brcm,nand-ecc-use-strap;
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm96855.dts b/arch/arm/boot/dts/broadcom/bcm96855.dts
new file mode 100644
index 000000000000..571663d9a1ea
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm96855.dts
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm6855.dtsi"
+
+/ {
+	model = "Broadcom BCM96855 Reference Board";
+	compatible = "brcm,bcm96855", "brcm,bcm6855", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&hsspi {
+	status = "okay";
+};
+
+&nand_controller {
+	brcm,wp-not-connected;
+	status = "okay";
+};
+
+&nandcs {
+	nand-on-flash-bbt;
+	brcm,nand-ecc-use-strap;
+};
diff --git a/arch/arm/boot/dts/broadcom/bcm96878.dts b/arch/arm/boot/dts/broadcom/bcm96878.dts
new file mode 100644
index 000000000000..8d6eddd54c6e
--- /dev/null
+++ b/arch/arm/boot/dts/broadcom/bcm96878.dts
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm6878.dtsi"
+
+/ {
+	model = "Broadcom BCM96878 Reference Board";
+	compatible = "brcm,bcm96878", "brcm,bcm6878", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&hsspi {
+	status = "okay";
+};
+
+&nand_controller {
+	brcm,wp-not-connected;
+	status = "okay";
+};
+
+&nandcs {
+	nand-on-flash-bbt;
+	brcm,nand-ecc-use-strap;
+};
diff --git a/arch/arm/boot/dts/bcm988312hr.dts b/arch/arm/boot/dts/broadcom/bcm988312hr.dts
index 007e34715956..663a3f27b6e4 100644
--- a/arch/arm/boot/dts/bcm988312hr.dts
+++ b/arch/arm/boot/dts/broadcom/bcm988312hr.dts
@@ -139,8 +139,7 @@
 
 &qspi {
 	status = "okay";
-	bspi-sel = <0>;
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p80";
diff --git a/arch/arm/boot/dts/bcm9hmidc.dtsi b/arch/arm/boot/dts/broadcom/bcm9hmidc.dtsi
index 65397c088335..65397c088335 100644
--- a/arch/arm/boot/dts/bcm9hmidc.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm9hmidc.dtsi
diff --git a/arch/arm/boot/dts/calxeda/Makefile b/arch/arm/boot/dts/calxeda/Makefile
new file mode 100644
index 000000000000..f5126b6d26ad
--- /dev/null
+++ b/arch/arm/boot/dts/calxeda/Makefile
@@ -0,0 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_HIGHBANK) += \
+	highbank.dtb \
+	ecx-2000.dtb
+dtb-$(CONFIG_ARCH_HIGHBANK) += \
+	highbank.dtb \
+	ecx-2000.dtb
diff --git a/arch/arm/boot/dts/ecx-2000.dts b/arch/arm/boot/dts/calxeda/ecx-2000.dts
index f6eb71553b95..f6eb71553b95 100644
--- a/arch/arm/boot/dts/ecx-2000.dts
+++ b/arch/arm/boot/dts/calxeda/ecx-2000.dts
diff --git a/arch/arm/boot/dts/ecx-common.dtsi b/arch/arm/boot/dts/calxeda/ecx-common.dtsi
index 57a028a69373..ce5221c6b358 100644
--- a/arch/arm/boot/dts/ecx-common.dtsi
+++ b/arch/arm/boot/dts/calxeda/ecx-common.dtsi
@@ -9,11 +9,11 @@
 	};
 
 	psci {
-		compatible	= "arm,psci";
-		method		= "smc";
-		cpu_suspend	= <0x84000002>;
-		cpu_off		= <0x84000004>;
-		cpu_on		= <0x84000006>;
+		compatible = "arm,psci";
+		method = "smc";
+		cpu_suspend = <0x84000002>;
+		cpu_off = <0x84000004>;
+		cpu_on = <0x84000006>;
 	};
 
 	soc {
diff --git a/arch/arm/boot/dts/highbank.dts b/arch/arm/boot/dts/calxeda/highbank.dts
index b6b0225a769e..b6b0225a769e 100644
--- a/arch/arm/boot/dts/highbank.dts
+++ b/arch/arm/boot/dts/calxeda/highbank.dts
diff --git a/arch/arm/boot/dts/cirrus/Makefile b/arch/arm/boot/dts/cirrus/Makefile
new file mode 100644
index 000000000000..e6015983e464
--- /dev/null
+++ b/arch/arm/boot/dts/cirrus/Makefile
@@ -0,0 +1,9 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_CLPS711X) += \
+	ep7211-edb7211.dtb
+dtb-$(CONFIG_ARCH_CLPS711X) += \
+	ep7211-edb7211.dtb
+dtb-$(CONFIG_ARCH_EP93XX) += \
+	ep93xx-edb9302.dtb \
+	ep93xx-bk3.dtb \
+	ep93xx-ts7250.dtb
diff --git a/arch/arm/boot/dts/ep7209.dtsi b/arch/arm/boot/dts/cirrus/ep7209.dtsi
index 57bdad2c1994..57bdad2c1994 100644
--- a/arch/arm/boot/dts/ep7209.dtsi
+++ b/arch/arm/boot/dts/cirrus/ep7209.dtsi
diff --git a/arch/arm/boot/dts/ep7211-edb7211.dts b/arch/arm/boot/dts/cirrus/ep7211-edb7211.dts
index 7fb532f227af..0b15ccaa762e 100644
--- a/arch/arm/boot/dts/ep7211-edb7211.dts
+++ b/arch/arm/boot/dts/cirrus/ep7211-edb7211.dts
@@ -30,7 +30,7 @@
 
 		display-timings {
 			native-mode = <&timing0>;
-			timing0: 320x240 {
+			timing0: timing-320x240 {
 				hactive = <320>;
 				hback-porch = <0>;
 				hfront-porch = <0>;
@@ -46,8 +46,8 @@
 
 	i2c: i2c {
 		compatible = "i2c-gpio";
-		gpios = <&portd 4 GPIO_ACTIVE_HIGH>,
-			<&portd 5 GPIO_ACTIVE_HIGH>;
+		sda-gpios = <&portd 4 GPIO_ACTIVE_HIGH>;
+		scl-gpios = <&portd 5 GPIO_ACTIVE_HIGH>;
 		i2c-gpio,delay-us = <2>;
 		i2c-gpio,scl-output-only;
 		#address-cells = <1>;
@@ -88,7 +88,7 @@
 };
 
 &portd {
-	lcden {
+	lcden-hog {
 		gpio-hog;
 		gpios = <2 GPIO_ACTIVE_HIGH>;
 		output-high;
diff --git a/arch/arm/boot/dts/ep7211.dtsi b/arch/arm/boot/dts/cirrus/ep7211.dtsi
index 32a4e1237145..32a4e1237145 100644
--- a/arch/arm/boot/dts/ep7211.dtsi
+++ b/arch/arm/boot/dts/cirrus/ep7211.dtsi
diff --git a/arch/arm/boot/dts/cirrus/ep93xx-bk3.dts b/arch/arm/boot/dts/cirrus/ep93xx-bk3.dts
new file mode 100644
index 000000000000..40bc9b2a6ba8
--- /dev/null
+++ b/arch/arm/boot/dts/cirrus/ep93xx-bk3.dts
@@ -0,0 +1,125 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for Liebherr controller BK3.1 based on Cirrus EP9302 SoC
+ */
+/dts-v1/;
+#include "ep93xx.dtsi"
+
+/ {
+	model = "Liebherr controller BK3.1";
+	compatible = "liebherr,bk3", "cirrus,ep9301";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	chosen {
+	};
+
+	memory@0 {
+		device_type = "memory";
+		/* should be set from ATAGS */
+		reg = <0x00000000 0x02000000>,
+		      <0x000530c0 0x01fdd000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-0 {
+			label = "grled";
+			gpios = <&gpio4 0 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			function = LED_FUNCTION_HEARTBEAT;
+		};
+
+		led-1 {
+			label = "rdled";
+			gpios = <&gpio4 1 GPIO_ACTIVE_HIGH>;
+			function = LED_FUNCTION_FAULT;
+		};
+	};
+};
+
+&ebi {
+	nand-controller@60000000 {
+		compatible = "technologic,ts7200-nand";
+		reg = <0x60000000 0x8000000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		nand@0 {
+			reg = <0>;
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				partition@0 {
+					label = "System";
+					reg = <0x00000000 0x01e00000>;
+					read-only;
+				};
+
+				partition@1e00000 {
+					label = "Data";
+					reg = <0x01e00000 0x05f20000>;
+				};
+
+				partition@7d20000 {
+					label = "RedBoot";
+					reg = <0x07d20000 0x002e0000>;
+					read-only;
+				};
+			};
+		};
+	};
+};
+
+&eth0 {
+	phy-handle = <&phy0>;
+};
+
+&i2s {
+	dmas = <&dma0 0 1>, <&dma0 0 2>;
+	dma-names = "tx", "rx";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_on_ac97_pins>;
+	status = "okay";
+};
+
+&gpio1 {
+	/* PWM */
+	gpio-ranges = <&syscon 6 163 1>;
+};
+
+&gpio4 {
+	gpio-ranges = <&syscon 0 97 2>;
+	status = "okay";
+};
+
+&gpio6 {
+	gpio-ranges = <&syscon 0 87 2>;
+	status = "okay";
+};
+
+&gpio7 {
+	gpio-ranges = <&syscon 2 199 4>;
+	status = "okay";
+};
+
+&mdio0 {
+	phy0: ethernet-phy@1 {
+		reg = <1>;
+		device_type = "ethernet-phy";
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/cirrus/ep93xx-edb9302.dts b/arch/arm/boot/dts/cirrus/ep93xx-edb9302.dts
new file mode 100644
index 000000000000..312b2be1c638
--- /dev/null
+++ b/arch/arm/boot/dts/cirrus/ep93xx-edb9302.dts
@@ -0,0 +1,181 @@
+// SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+/*
+ * Device Tree file for Cirrus Logic EDB9302 board based on EP9302 SoC
+ */
+/dts-v1/;
+#include "ep93xx.dtsi"
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "cirrus,edb9302", "cirrus,ep9301";
+	model = "cirrus,edb9302";
+
+	chosen {
+	};
+
+	memory@0 {
+		device_type = "memory";
+		/* should be set from ATAGS */
+		reg = <0x0000000 0x800000>,
+		      <0x1000000 0x800000>,
+		      <0x4000000 0x800000>,
+		      <0x5000000 0x800000>;
+	};
+
+	sound {
+		compatible = "audio-graph-card2";
+		label = "EDB93XX";
+		links = <&i2s_port>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-0 {
+			label = "grled";
+			gpios = <&gpio4 0 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			function = LED_FUNCTION_HEARTBEAT;
+		};
+
+		led-1 {
+			label = "rdled";
+			gpios = <&gpio4 1 GPIO_ACTIVE_HIGH>;
+			function = LED_FUNCTION_FAULT;
+		};
+	};
+};
+
+&adc {
+	status = "okay";
+};
+
+&ebi {
+	flash@60000000 {
+		compatible = "cfi-flash";
+		reg = <0x60000000 0x1000000>;
+		bank-width = <2>;
+	};
+};
+
+&eth0 {
+	phy-handle = <&phy0>;
+};
+
+&gpio0 {
+	gpio-ranges = <&syscon 0 153 1>,
+		      <&syscon 1 152 1>,
+		      <&syscon 2 151 1>,
+		      <&syscon 3 148 1>,
+		      <&syscon 4 147 1>,
+		      <&syscon 5 146 1>,
+		      <&syscon 6 145 1>,
+		      <&syscon 7 144 1>;
+};
+
+&gpio1 {
+	gpio-ranges = <&syscon 0 143 1>,
+		      <&syscon 1 142 1>,
+		      <&syscon 2 141 1>,
+		      <&syscon 3 140 1>,
+		      <&syscon 4 165 1>,
+		      <&syscon 5 164 1>,
+		      <&syscon 6 163 1>,
+		      <&syscon 7 160 1>;
+};
+
+&gpio2 {
+	gpio-ranges = <&syscon 0 115 1>;
+};
+
+/* edb9302 doesn't have GPIO Port D present */
+&gpio3 {
+	status = "disabled";
+};
+
+&gpio4 {
+	gpio-ranges = <&syscon 0 97 2>;
+};
+
+&gpio5 {
+	gpio-ranges = <&syscon 1 170 1>,
+		      <&syscon 2 169 1>,
+		      <&syscon 3 168 1>;
+};
+
+&gpio6 {
+	gpio-ranges = <&syscon 0 87 2>;
+};
+
+&gpio7 {
+	gpio-ranges = <&syscon 2 199 4>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_on_ac97_pins>;
+	status = "okay";
+	i2s_port: port {
+		i2s_ep: endpoint {
+			system-clock-direction-out;
+			frame-master;
+			bitclock-master;
+			mclk-fs = <256>;
+			dai-format = "i2s";
+			convert-channels = <2>;
+			convert-sample-format = "s32_le";
+			remote-endpoint = <&codec_ep>;
+		};
+	};
+};
+
+&mdio0 {
+	phy0: ethernet-phy@1 {
+		reg = <1>;
+		device_type = "ethernet-phy";
+	};
+};
+
+&spi0 {
+	cs-gpios = <&gpio0 6 GPIO_ACTIVE_LOW
+		    &gpio0 7 GPIO_ACTIVE_LOW>;
+	dmas = <&dma1 10 2>, <&dma1 10 1>;
+	dma-names = "rx", "tx";
+	status = "okay";
+
+	cs4271: codec@0 {
+		compatible = "cirrus,cs4271";
+		reg = <0>;
+		#sound-dai-cells = <0>;
+		spi-max-frequency = <6000000>;
+		spi-cpol;
+		spi-cpha;
+		reset-gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
+		port {
+			codec_ep: endpoint {
+				remote-endpoint = <&i2s_ep>;
+			};
+		};
+	};
+
+	at25f1024: eeprom@1 {
+		compatible = "atmel,at25";
+		reg = <1>;
+		address-width = <8>;
+		size = <0x20000>;
+		pagesize = <256>;
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/cirrus/ep93xx-ts7250.dts b/arch/arm/boot/dts/cirrus/ep93xx-ts7250.dts
new file mode 100644
index 000000000000..9e03f93d9fc8
--- /dev/null
+++ b/arch/arm/boot/dts/cirrus/ep93xx-ts7250.dts
@@ -0,0 +1,145 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for Technologic Systems ts7250 board based on Cirrus EP9302 SoC
+ */
+/dts-v1/;
+#include "ep93xx.dtsi"
+
+/ {
+	compatible = "technologic,ts7250", "cirrus,ep9301";
+	model = "TS-7250 SBC";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	chosen {
+	};
+
+	memory@0 {
+		device_type = "memory";
+		/* should be set from ATAGS */
+		reg = <0x00000000 0x02000000>,
+		      <0x000530c0 0x01fdd000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-0 {
+			label = "grled";
+			gpios = <&gpio4 0 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			function = LED_FUNCTION_HEARTBEAT;
+		};
+
+		led-1 {
+			label = "rdled";
+			gpios = <&gpio4 1 GPIO_ACTIVE_HIGH>;
+			function = LED_FUNCTION_FAULT;
+		};
+	};
+};
+
+&ebi {
+	nand-controller@60000000 {
+		compatible = "technologic,ts7200-nand";
+		reg = <0x60000000 0x8000000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		nand@0 {
+			reg = <0>;
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				partition@0 {
+					label = "TS-BOOTROM";
+					reg = <0x00000000 0x00020000>;
+					read-only;
+				};
+
+				partition@20000 {
+					label = "Linux";
+					reg = <0x00020000 0x07d00000>;
+				};
+
+				partition@7d20000 {
+					label = "RedBoot";
+					reg = <0x07d20000 0x002e0000>;
+					read-only;
+				};
+			};
+		};
+	};
+
+	rtc@10800000 {
+		compatible = "st,m48t86";
+		reg = <0x10800000 0x1>,
+			<0x11700000 0x1>;
+	};
+
+	watchdog@23800000 {
+		compatible = "technologic,ts7200-wdt";
+		reg = <0x23800000 0x01>,
+			<0x23c00000 0x01>;
+		timeout-sec = <30>;
+	};
+};
+
+&eth0 {
+	phy-handle = <&phy0>;
+};
+
+&gpio1 {
+	/* PWM */
+	gpio-ranges = <&syscon 6 163 1>;
+};
+
+/* ts7250 doesn't have GPIO Port D present */
+&gpio3 {
+	status = "disabled";
+};
+
+&gpio4 {
+	gpio-ranges = <&syscon 0 97 2>;
+};
+
+&gpio6 {
+	gpio-ranges = <&syscon 0 87 2>;
+};
+
+&gpio7 {
+	gpio-ranges = <&syscon 2 199 4>;
+};
+
+&spi0 {
+	cs-gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+	dmas = <&dma1 10 2>, <&dma1 10 1>;
+	dma-names = "rx", "tx";
+	status = "okay";
+
+	tmp122: temperature-sensor@0 {
+		compatible = "ti,tmp122";
+		reg = <0>;
+		spi-max-frequency = <2000000>;
+	};
+};
+
+&mdio0 {
+	phy0: ethernet-phy@1 {
+		reg = <1>;
+		device_type = "ethernet-phy";
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/cirrus/ep93xx.dtsi b/arch/arm/boot/dts/cirrus/ep93xx.dtsi
new file mode 100644
index 000000000000..0dd1eee346ca
--- /dev/null
+++ b/arch/arm/boot/dts/cirrus/ep93xx.dtsi
@@ -0,0 +1,444 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for Cirrus Logic systems EP93XX SoC
+ */
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/clock/cirrus,ep9301-syscon.h>
+/ {
+	soc: soc {
+		compatible = "simple-bus";
+		ranges;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		syscon: syscon@80930000 {
+			compatible = "cirrus,ep9301-syscon", "syscon";
+			reg = <0x80930000 0x1000>;
+
+			#clock-cells = <1>;
+			clocks = <&xtali>;
+
+			spi_default_pins: pins-spi {
+				function = "spi";
+				groups = "ssp";
+			};
+
+			ac97_default_pins: pins-ac97 {
+				function = "ac97";
+				groups = "ac97";
+			};
+
+			i2s_on_ssp_pins: pins-i2sonssp {
+				function = "i2s";
+				groups = "i2s_on_ssp";
+			};
+
+			i2s_on_ac97_pins: pins-i2sonac97 {
+				function = "i2s";
+				groups = "i2s_on_ac97";
+			};
+
+			gpio1_default_pins: pins-gpio1 {
+				function = "gpio";
+				groups = "gpio1agrp";
+			};
+
+			pwm1_default_pins: pins-pwm1 {
+				function = "pwm";
+				groups = "pwm1";
+			};
+
+			gpio2_default_pins: pins-gpio2 {
+				function = "gpio";
+				groups = "gpio2agrp";
+			};
+
+			gpio3_default_pins: pins-gpio3 {
+				function = "gpio";
+				groups = "gpio3agrp";
+			};
+
+			keypad_default_pins: pins-keypad {
+				function = "keypad";
+				groups = "keypadgrp";
+			};
+
+			gpio4_default_pins: pins-gpio4 {
+				function = "gpio";
+				groups = "gpio4agrp";
+			};
+
+			gpio6_default_pins: pins-gpio6 {
+				function = "gpio";
+				groups = "gpio6agrp";
+			};
+
+			gpio7_default_pins: pins-gpio7 {
+				function = "gpio";
+				groups = "gpio7agrp";
+			};
+
+			ide_default_pins: pins-ide {
+				function = "pata";
+				groups = "idegrp";
+			};
+
+			lcd_on_dram0_pins: pins-rasteronsdram0 {
+				function = "lcd";
+				groups = "rasteronsdram0grp";
+			};
+
+			lcd_on_dram3_pins: pins-rasteronsdram3 {
+				function = "lcd";
+				groups = "rasteronsdram3grp";
+			};
+		};
+
+		adc: adc@80900000 {
+			compatible = "cirrus,ep9301-adc";
+			reg = <0x80900000 0x28>;
+			clocks = <&syscon EP93XX_CLK_ADC>;
+			interrupt-parent = <&vic0>;
+			interrupts = <30>;
+			status = "disabled";
+		};
+
+		/*
+		 * The EP93XX expansion bus is a set of up to 7 each up to 16MB
+		 * windows in the 256MB space from 0x50000000 to 0x5fffffff.
+		 * But since we don't require to setup it in any way, we can
+		 * represent it as a simple-bus.
+		 */
+		ebi: bus@80080000 {
+			compatible = "simple-bus";
+			reg = <0x80080000 0x20>;
+			native-endian;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+		};
+
+		dma0: dma-controller@80000000 {
+			compatible = "cirrus,ep9301-dma-m2p";
+			reg = <0x80000000 0x0040>,
+			      <0x80000040 0x0040>,
+			      <0x80000080 0x0040>,
+			      <0x800000c0 0x0040>,
+			      <0x80000240 0x0040>,
+			      <0x80000200 0x0040>,
+			      <0x800002c0 0x0040>,
+			      <0x80000280 0x0040>,
+			      <0x80000340 0x0040>,
+			      <0x80000300 0x0040>;
+			clocks = <&syscon EP93XX_CLK_M2P0>,
+				 <&syscon EP93XX_CLK_M2P1>,
+				 <&syscon EP93XX_CLK_M2P2>,
+				 <&syscon EP93XX_CLK_M2P3>,
+				 <&syscon EP93XX_CLK_M2P4>,
+				 <&syscon EP93XX_CLK_M2P5>,
+				 <&syscon EP93XX_CLK_M2P6>,
+				 <&syscon EP93XX_CLK_M2P7>,
+				 <&syscon EP93XX_CLK_M2P8>,
+				 <&syscon EP93XX_CLK_M2P9>;
+			clock-names = "m2p0", "m2p1",
+				      "m2p2", "m2p3",
+				      "m2p4", "m2p5",
+				      "m2p6", "m2p7",
+				      "m2p8", "m2p9";
+			interrupt-parent = <&vic0>;
+			interrupts = <7>, <8>, <9>, <10>, <11>,
+				<12>, <13>, <14>, <15>, <16>;
+			#dma-cells = <2>;
+		};
+
+		dma1: dma-controller@80000100 {
+			compatible = "cirrus,ep9301-dma-m2m";
+			reg = <0x80000100 0x0040>,
+			      <0x80000140 0x0040>;
+			clocks = <&syscon EP93XX_CLK_M2M0>,
+				 <&syscon EP93XX_CLK_M2M1>;
+			clock-names = "m2m0", "m2m1";
+			interrupt-parent = <&vic0>;
+			interrupts = <17>, <18>;
+			#dma-cells = <2>;
+		};
+
+		eth0: ethernet@80010000 {
+			compatible = "cirrus,ep9301-eth";
+			reg = <0x80010000 0x10000>;
+			interrupt-parent = <&vic1>;
+			interrupts = <7>;
+			mdio0: mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		gpio0: gpio@80840000 {
+			compatible = "cirrus,ep9301-gpio";
+			reg = <0x80840000 0x04>,
+			      <0x80840010 0x04>,
+			      <0x80840090 0x1c>;
+			reg-names = "data", "dir", "intr";
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupt-parent = <&vic1>;
+			interrupts = <27>;
+		};
+
+		gpio1: gpio@80840004 {
+			compatible = "cirrus,ep9301-gpio";
+			reg = <0x80840004 0x04>,
+			      <0x80840014 0x04>,
+			      <0x808400ac 0x1c>;
+			reg-names = "data", "dir", "intr";
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupt-parent = <&vic1>;
+			interrupts = <27>;
+		};
+
+		gpio2: gpio@80840008 {
+			compatible = "cirrus,ep9301-gpio";
+			reg = <0x80840008 0x04>,
+			      <0x80840018 0x04>;
+			reg-names = "data", "dir";
+			gpio-controller;
+			#gpio-cells = <2>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&gpio2_default_pins>;
+		};
+
+		gpio3: gpio@8084000c {
+			compatible = "cirrus,ep9301-gpio";
+			reg = <0x8084000c 0x04>,
+			      <0x8084001c 0x04>;
+			reg-names = "data", "dir";
+			gpio-controller;
+			#gpio-cells = <2>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&gpio3_default_pins>;
+		};
+
+		gpio4: gpio@80840020 {
+			compatible = "cirrus,ep9301-gpio";
+			reg = <0x80840020 0x04>,
+			      <0x80840024 0x04>;
+			reg-names = "data", "dir";
+			gpio-controller;
+			#gpio-cells = <2>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&gpio4_default_pins>;
+		};
+
+		gpio5: gpio@80840030 {
+			compatible = "cirrus,ep9301-gpio";
+			reg = <0x80840030 0x04>,
+			      <0x80840034 0x04>,
+			      <0x8084004c 0x1c>;
+			reg-names = "data", "dir", "intr";
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts-extended = <&vic0 19>, <&vic0 20>,
+					      <&vic0 21>, <&vic0 22>,
+					      <&vic1 15>, <&vic1 16>,
+					      <&vic1 17>, <&vic1 18>;
+		};
+
+		gpio6: gpio@80840038 {
+			compatible = "cirrus,ep9301-gpio";
+			reg = <0x80840038 0x04>,
+			      <0x8084003c 0x04>;
+			reg-names = "data", "dir";
+			gpio-controller;
+			#gpio-cells = <2>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&gpio6_default_pins>;
+		};
+
+		gpio7: gpio@80840040 {
+			compatible = "cirrus,ep9301-gpio";
+			reg = <0x80840040 0x04>,
+			      <0x80840044 0x04>;
+			reg-names = "data", "dir";
+			gpio-controller;
+			#gpio-cells = <2>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&gpio7_default_pins>;
+		};
+
+		i2s: i2s@80820000 {
+			compatible = "cirrus,ep9301-i2s";
+			reg = <0x80820000 0x100>;
+			#sound-dai-cells = <0>;
+			interrupt-parent = <&vic1>;
+			interrupts = <28>;
+			clocks = <&syscon EP93XX_CLK_I2S_MCLK>,
+				 <&syscon EP93XX_CLK_I2S_SCLK>,
+				 <&syscon EP93XX_CLK_I2S_LRCLK>;
+			clock-names = "mclk", "sclk", "lrclk";
+			dmas = <&dma0 0 1>, <&dma0 0 2>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		ide: ide@800a0000 {
+			compatible = "cirrus,ep9312-pata";
+			reg = <0x800a0000 0x38>;
+			interrupt-parent = <&vic1>;
+			interrupts = <8>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&ide_default_pins>;
+			status = "disabled";
+		};
+
+		vic0: interrupt-controller@800b0000 {
+			compatible = "arm,pl192-vic";
+			reg = <0x800b0000 0x1000>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			valid-mask = <0x7ffffffc>;
+			valid-wakeup-mask = <0x0>;
+		};
+
+		vic1: interrupt-controller@800c0000 {
+			compatible = "arm,pl192-vic";
+			reg = <0x800c0000 0x1000>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			valid-mask = <0x1fffffff>;
+			valid-wakeup-mask = <0x0>;
+		};
+
+		keypad: keypad@800f0000 {
+			compatible = "cirrus,ep9307-keypad";
+			reg = <0x800f0000 0x0c>;
+			interrupt-parent = <&vic0>;
+			interrupts = <29>;
+			clocks = <&syscon EP93XX_CLK_KEYPAD>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&keypad_default_pins>;
+			linux,keymap =	<KEY_UP>,
+					<KEY_DOWN>,
+					<KEY_VOLUMEDOWN>,
+					<KEY_HOME>,
+					<KEY_RIGHT>,
+					<KEY_LEFT>,
+					<KEY_ENTER>,
+					<KEY_VOLUMEUP>,
+					<KEY_F6>,
+					<KEY_F8>,
+					<KEY_F9>,
+					<KEY_F10>,
+					<KEY_F1>,
+					<KEY_F2>,
+					<KEY_F3>,
+					<KEY_POWER>;
+		};
+
+		pwm0: pwm@80910000 {
+			compatible = "cirrus,ep9301-pwm";
+			reg = <0x80910000 0x10>;
+			clocks = <&syscon EP93XX_CLK_PWM>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
+		pwm1: pwm@80910020 {
+			compatible = "cirrus,ep9301-pwm";
+			reg = <0x80910020 0x10>;
+			clocks = <&syscon EP93XX_CLK_PWM>;
+			#pwm-cells = <3>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pwm1_default_pins>;
+			status = "disabled";
+		};
+
+		rtc0: rtc@80920000 {
+			compatible = "cirrus,ep9301-rtc";
+			reg = <0x80920000 0x100>;
+		};
+
+		spi0: spi@808a0000 {
+			compatible = "cirrus,ep9301-spi";
+			reg = <0x808a0000 0x18>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupt-parent = <&vic1>;
+			interrupts = <21>;
+			clocks = <&syscon EP93XX_CLK_SPI>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi_default_pins>;
+			status = "disabled";
+		};
+
+		timer: timer@80810000 {
+			compatible = "cirrus,ep9301-timer";
+			reg = <0x80810000 0x100>;
+			interrupt-parent = <&vic1>;
+			interrupts = <19>;
+		};
+
+		uart0: serial@808c0000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x808c0000 0x1000>;
+			arm,primecell-periphid = <0x00041010>;
+			clocks = <&syscon EP93XX_CLK_UART1>, <&syscon EP93XX_CLK_UART>;
+			clock-names = "uartclk", "apb_pclk";
+			interrupt-parent = <&vic1>;
+			interrupts = <20>;
+			status = "disabled";
+		};
+
+		uart1: uart@808d0000 {
+			compatible = "arm,primecell";
+			reg = <0x808d0000 0x1000>;
+			arm,primecell-periphid = <0x00041010>;
+			clocks = <&syscon EP93XX_CLK_UART2>, <&syscon EP93XX_CLK_UART>;
+			clock-names = "apb:uart2", "apb_pclk";
+			interrupt-parent = <&vic1>;
+			interrupts = <22>;
+			status = "disabled";
+		};
+
+		uart2: uart@808b0000 {
+			compatible = "arm,primecell";
+			reg = <0x808b0000 0x1000>;
+			arm,primecell-periphid = <0x00041010>;
+			clocks = <&syscon EP93XX_CLK_UART3>, <&syscon EP93XX_CLK_UART>;
+			clock-names = "apb:uart3", "apb_pclk";
+			interrupt-parent = <&vic1>;
+			interrupts = <23>;
+			status = "disabled";
+		};
+
+		usb0: usb@80020000 {
+			compatible = "generic-ohci";
+			reg = <0x80020000 0x10000>;
+			interrupt-parent = <&vic1>;
+			interrupts = <24>;
+			clocks = <&syscon EP93XX_CLK_USB>;
+			status = "disabled";
+		};
+
+		watchdog0: watchdog@80940000 {
+			compatible = "cirrus,ep9301-wdt";
+			reg = <0x80940000 0x08>;
+		};
+	};
+
+	xtali: oscillator {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <14745600>;
+		clock-output-names = "xtali";
+	};
+};
diff --git a/arch/arm/boot/dts/cnxt/Makefile b/arch/arm/boot/dts/cnxt/Makefile
new file mode 100644
index 000000000000..d49df53f65a1
--- /dev/null
+++ b/arch/arm/boot/dts/cnxt/Makefile
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_DIGICOLOR) += \
+	cx92755_equinox.dtb
+dtb-$(CONFIG_ARCH_DIGICOLOR) += \
+	cx92755_equinox.dtb
diff --git a/arch/arm/boot/dts/cx92755.dtsi b/arch/arm/boot/dts/cnxt/cx92755.dtsi
index d2e8f36f8c60..227675fbe820 100644
--- a/arch/arm/boot/dts/cx92755.dtsi
+++ b/arch/arm/boot/dts/cnxt/cx92755.dtsi
@@ -107,7 +107,7 @@
 		reg = <0xf00003a0 0x10>;
 	};
 
-	uart0: uart@f0000740 {
+	uart0: serial@f0000740 {
 		compatible = "cnxt,cx92755-usart";
 		reg = <0xf0000740 0x20>;
 		clocks = <&main_clk>;
@@ -115,7 +115,7 @@
 		status = "disabled";
 	};
 
-	uart1: uart@f0000760 {
+	uart1: serial@f0000760 {
 		compatible = "cnxt,cx92755-usart";
 		reg = <0xf0000760 0x20>;
 		clocks = <&main_clk>;
@@ -123,7 +123,7 @@
 		status = "disabled";
 	};
 
-	uart2: uart@f0000780 {
+	uart2: serial@f0000780 {
 		compatible = "cnxt,cx92755-usart";
 		reg = <0xf0000780 0x20>;
 		clocks = <&main_clk>;
diff --git a/arch/arm/boot/dts/cx92755_equinox.dts b/arch/arm/boot/dts/cnxt/cx92755_equinox.dts
index 026f556c8c50..026f556c8c50 100644
--- a/arch/arm/boot/dts/cx92755_equinox.dts
+++ b/arch/arm/boot/dts/cnxt/cx92755_equinox.dts
diff --git a/arch/arm/boot/dts/gemini/Makefile b/arch/arm/boot/dts/gemini/Makefile
new file mode 100644
index 000000000000..f9f63ce3eb49
--- /dev/null
+++ b/arch/arm/boot/dts/gemini/Makefile
@@ -0,0 +1,12 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_GEMINI) += \
+	gemini-dlink-dir-685.dtb \
+	gemini-dlink-dns-313.dtb \
+	gemini-nas4220b.dtb \
+	gemini-ns2502.dtb \
+	gemini-rut1xx.dtb \
+	gemini-sl93512r.dtb \
+	gemini-sq201.dtb \
+	gemini-ssi1328.dtb \
+	gemini-wbd111.dtb \
+	gemini-wbd222.dtb
diff --git a/arch/arm/boot/dts/gemini-dlink-dir-685.dts b/arch/arm/boot/dts/gemini/gemini-dlink-dir-685.dts
index 396149664297..b4dbcf8f168e 100644
--- a/arch/arm/boot/dts/gemini-dlink-dir-685.dts
+++ b/arch/arm/boot/dts/gemini/gemini-dlink-dir-685.dts
@@ -27,10 +27,10 @@
 	gpio_keys {
 		compatible = "gpio-keys";
 
-		button-esc {
+		button-reset {
 			debounce-interval = <100>;
 			wakeup-source;
-			linux,code = <KEY_ESC>;
+			linux,code = <KEY_RESTART>;
 			label = "reset";
 			/* Collides with LPC_LAD[0], UART DCD, SSP 97RST */
 			gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
@@ -187,7 +187,7 @@
 	};
 
 	/* This is a RealTek RTL8366RB switch and PHY using SMI over GPIO */
-	switch {
+	ethernet-switch {
 		compatible = "realtek,rtl8366rb";
 		/* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */
 		mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>;
@@ -204,36 +204,36 @@
 			#interrupt-cells = <1>;
 		};
 
-		ports {
+		ethernet-ports {
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			port@0 {
+			ethernet-port@0 {
 				reg = <0>;
 				label = "lan0";
 				phy-handle = <&phy0>;
 			};
-			port@1 {
+			ethernet-port@1 {
 				reg = <1>;
 				label = "lan1";
 				phy-handle = <&phy1>;
 			};
-			port@2 {
+			ethernet-port@2 {
 				reg = <2>;
 				label = "lan2";
 				phy-handle = <&phy2>;
 			};
-			port@3 {
+			ethernet-port@3 {
 				reg = <3>;
 				label = "lan3";
 				phy-handle = <&phy3>;
 			};
-			port@4 {
+			ethernet-port@4 {
 				reg = <4>;
 				label = "wan";
 				phy-handle = <&phy4>;
 			};
-			rtl8366rb_cpu_port: port@5 {
+			rtl8366rb_cpu_port: ethernet-port@5 {
 				reg = <5>;
 				label = "cpu";
 				ethernet = <&gmac0>;
@@ -252,27 +252,27 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			phy0: phy@0 {
+			phy0: ethernet-phy@0 {
 				reg = <0>;
 				interrupt-parent = <&switch_intc>;
 				interrupts = <0>;
 			};
-			phy1: phy@1 {
+			phy1: ethernet-phy@1 {
 				reg = <1>;
 				interrupt-parent = <&switch_intc>;
 				interrupts = <1>;
 			};
-			phy2: phy@2 {
+			phy2: ethernet-phy@2 {
 				reg = <2>;
 				interrupt-parent = <&switch_intc>;
 				interrupts = <2>;
 			};
-			phy3: phy@3 {
+			phy3: ethernet-phy@3 {
 				reg = <3>;
 				interrupt-parent = <&switch_intc>;
 				interrupts = <3>;
 			};
-			phy4: phy@4 {
+			phy4: ethernet-phy@4 {
 				reg = <4>;
 				interrupt-parent = <&switch_intc>;
 				interrupts = <12>;
diff --git a/arch/arm/boot/dts/gemini-dlink-dns-313.dts b/arch/arm/boot/dts/gemini/gemini-dlink-dns-313.dts
index eba1c94ed7f7..8c54d3a5a721 100644
--- a/arch/arm/boot/dts/gemini-dlink-dns-313.dts
+++ b/arch/arm/boot/dts/gemini/gemini-dlink-dns-313.dts
@@ -33,10 +33,10 @@
 	gpio_keys {
 		compatible = "gpio-keys";
 
-		button-esc {
+		button-reset {
 			debounce-interval = <100>;
 			wakeup-source;
-			linux,code = <KEY_ESC>;
+			linux,code = <KEY_RESTART>;
 			label = "reset";
 			gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
 		};
@@ -80,6 +80,15 @@
 		#cooling-cells = <2>;
 	};
 
+	/*
+	 * This is the type B USB connector on the device,
+	 * a GPIO-controlled USB VBUS detect
+	 */
+	usb1_phy: phy {
+		compatible = "gpio-usb-b-connector", "usb-b-connector";
+		#phy-cells = <0>;
+		vbus-gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
+	};
 
 	/* Global Mixed-Mode Technology G751 mounted on GPIO I2C */
 	i2c {
@@ -164,6 +173,8 @@
 			compatible = "cortina,gemini-flash", "jedec-flash";
 			status = "okay";
 			reg = <0x30000000 0x00080000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 
 			/*
 			 * This "RedBoot" is the Storlink derivative.
@@ -300,5 +311,13 @@
 		ide@63000000 {
 			status = "okay";
 		};
+
+		usb@69000000 {
+			status = "okay";
+			dr_mode = "peripheral";
+			usb-phy = <&usb1_phy>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&usb_default_pins>;
+		};
 	};
 };
diff --git a/arch/arm/boot/dts/gemini-nas4220b.dts b/arch/arm/boot/dts/gemini/gemini-nas4220b.dts
index 6544c730340f..6544c730340f 100644
--- a/arch/arm/boot/dts/gemini-nas4220b.dts
+++ b/arch/arm/boot/dts/gemini/gemini-nas4220b.dts
diff --git a/arch/arm/boot/dts/gemini-ns2502.dts b/arch/arm/boot/dts/gemini/gemini-ns2502.dts
index 704abd212df5..e6eeb35e8819 100644
--- a/arch/arm/boot/dts/gemini-ns2502.dts
+++ b/arch/arm/boot/dts/gemini/gemini-ns2502.dts
@@ -39,10 +39,6 @@
 		phy0: ethernet-phy@1 {
 			reg = <1>;
 			device_type = "ethernet-phy";
-			/* We lack the knowledge of necessary GPIO to achieve
-			 * Gigabit
-			 */
-			max-speed = <100>;
 		};
 	};
 };
@@ -50,7 +46,7 @@
 &ethernet {
 	status = "okay";
 	ethernet-port@0 {
-		phy-mode = "rgmii";
+		phy-mode = "rgmii-id";
 		phy-handle = <&phy0>;
 	};
 };
@@ -65,30 +61,9 @@
 	pinctrl-1 = <&pflash_disabled_pins>;
 
 	partitions {
-		compatible = "fixed-partitions";
-		#address-cells = <1>;
-		#size-cells = <1>;
-
-		partition@0 {
-			label = "RedBoot";
-			reg = <0x00000000 0x00020000>;
-		};
-		partition@20000 {
-			label = "kernel";
-			reg = <0x00020000 0x00700000>;
-		};
-		partition@720000 {
-			label = "VCTL";
-			reg = <0x00720000 0x00020000>;
-		};
-		partition@740000 {
-			label = "CurConf";
-			reg = <0x00740000 0x000a0000>;
-		};
-		partition@7e0000 {
-			label = "FIS";
-			reg = <0x007e0000 0x00010000>;
-		};
+		compatible = "redboot-fis";
+		/* Eraseblock at 0x7e0000 */
+		fis-index-block = <0x3f>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/gemini-rut1xx.dts b/arch/arm/boot/dts/gemini/gemini-rut1xx.dts
index 0ebda4efd9d0..0ebda4efd9d0 100644
--- a/arch/arm/boot/dts/gemini-rut1xx.dts
+++ b/arch/arm/boot/dts/gemini/gemini-rut1xx.dts
diff --git a/arch/arm/boot/dts/gemini-sl93512r.dts b/arch/arm/boot/dts/gemini/gemini-sl93512r.dts
index 91c19e8ebfe8..4992ec276de9 100644
--- a/arch/arm/boot/dts/gemini-sl93512r.dts
+++ b/arch/arm/boot/dts/gemini/gemini-sl93512r.dts
@@ -43,7 +43,7 @@
 		button-setup {
 			debounce-interval = <50>;
 			wakeup-source;
-			linux,code = <KEY_SETUP>;
+			linux,code = <KEY_RESTART>;
 			label = "factory reset";
 			/* Conflict with NAND flash */
 			gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
@@ -93,7 +93,7 @@
 		cs-gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
 		num-chipselects = <1>;
 
-		switch@0 {
+		ethernet-switch@0 {
 			compatible = "vitesse,vsc7385";
 			reg = <0>;
 			/* Specified for 2.5 MHz or below */
@@ -101,27 +101,27 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 
-			ports {
+			ethernet-ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				port@0 {
+				ethernet-port@0 {
 					reg = <0>;
 					label = "lan1";
 				};
-				port@1 {
+				ethernet-port@1 {
 					reg = <1>;
 					label = "lan2";
 				};
-				port@2 {
+				ethernet-port@2 {
 					reg = <2>;
 					label = "lan3";
 				};
-				port@3 {
+				ethernet-port@3 {
 					reg = <3>;
 					label = "lan4";
 				};
-				vsc: port@6 {
+				vsc: ethernet-port@6 {
 					reg = <6>;
 					label = "cpu";
 					ethernet = <&gmac1>;
diff --git a/arch/arm/boot/dts/gemini-sq201.dts b/arch/arm/boot/dts/gemini/gemini-sq201.dts
index d0efd76695da..f8c6f6e5cdea 100644
--- a/arch/arm/boot/dts/gemini-sq201.dts
+++ b/arch/arm/boot/dts/gemini/gemini-sq201.dts
@@ -30,7 +30,7 @@
 		button-setup {
 			debounce-interval = <100>;
 			wakeup-source;
-			linux,code = <KEY_SETUP>;
+			linux,code = <KEY_RESTART>;
 			label = "factory reset";
 			/* Conflict with NAND flash */
 			gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
@@ -78,7 +78,7 @@
 		cs-gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
 		num-chipselects = <1>;
 
-		switch@0 {
+		ethernet-switch@0 {
 			compatible = "vitesse,vsc7395";
 			reg = <0>;
 			/* Specified for 2.5 MHz or below */
@@ -86,27 +86,27 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 
-			ports {
+			ethernet-ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				port@0 {
+				ethernet-port@0 {
 					reg = <0>;
 					label = "lan1";
 				};
-				port@1 {
+				ethernet-port@1 {
 					reg = <1>;
 					label = "lan2";
 				};
-				port@2 {
+				ethernet-port@2 {
 					reg = <2>;
 					label = "lan3";
 				};
-				port@3 {
+				ethernet-port@3 {
 					reg = <3>;
 					label = "lan4";
 				};
-				vsc: port@6 {
+				vsc: ethernet-port@6 {
 					reg = <6>;
 					label = "cpu";
 					ethernet = <&gmac1>;
diff --git a/arch/arm/boot/dts/gemini-ssi1328.dts b/arch/arm/boot/dts/gemini/gemini-ssi1328.dts
index 2b3e7db84fed..42e85f07cf76 100644
--- a/arch/arm/boot/dts/gemini-ssi1328.dts
+++ b/arch/arm/boot/dts/gemini/gemini-ssi1328.dts
@@ -40,10 +40,6 @@
 		phy0: ethernet-phy@1 {
 			reg = <1>;
 			device_type = "ethernet-phy";
-			/* We lack the knowledge of necessary GPIO to achieve
-			 * Gigabit
-			 */
-			max-speed = <100>;
 		};
 		/* WAN ICPlus IP101A */
 		phy1: ethernet-phy@2 {
diff --git a/arch/arm/boot/dts/gemini-wbd111.dts b/arch/arm/boot/dts/gemini/gemini-wbd111.dts
index de3c4416b0fb..6a0c89e0c918 100644
--- a/arch/arm/boot/dts/gemini-wbd111.dts
+++ b/arch/arm/boot/dts/gemini/gemini-wbd111.dts
@@ -10,7 +10,7 @@
 
 / {
 	model = "Wiliboard WBD-111";
-	compatible = "wiliboard,wbd111", "cortina,gemini";
+	compatible = "wiligear,wiliboard-wbd111", "cortina,gemini";
 	#address-cells = <1>;
 	#size-cells = <1>;
 
@@ -28,10 +28,10 @@
 	gpio_keys {
 		compatible = "gpio-keys";
 
-		button-setup {
+		button-reset {
 			debounce-interval = <100>;
 			wakeup-source;
-			linux,code = <KEY_SETUP>;
+			linux,code = <KEY_RESTART>;
 			label = "reset";
 			/* Conflict with ICE */
 			gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
@@ -87,33 +87,10 @@
 			/* 8MB of flash */
 			reg = <0x30000000 0x00800000>;
 
-			partition@0 {
-				label = "RedBoot";
-				reg = <0x00000000 0x00020000>;
-				read-only;
-			};
-			partition@20000 {
-				label = "kernel";
-				reg = <0x00020000 0x00100000>;
-			};
-			partition@120000 {
-				label = "rootfs";
-				reg = <0x00120000 0x006a0000>;
-			};
-			partition@7c0000 {
-				label = "VCTL";
-				reg = <0x007c0000 0x00010000>;
-				read-only;
-			};
-			partition@7d0000 {
-				label = "cfg";
-				reg = <0x007d0000 0x00010000>;
-				read-only;
-			};
-			partition@7e0000 {
-				label = "FIS";
-				reg = <0x007e0000 0x00010000>;
-				read-only;
+			partitions {
+				compatible = "redboot-fis";
+				/* Eraseblock at 0x7e0000 */
+				fis-index-block = <0x3f>;
 			};
 		};
 
diff --git a/arch/arm/boot/dts/gemini-wbd222.dts b/arch/arm/boot/dts/gemini/gemini-wbd222.dts
index e5ceaadbcc1a..d8b34ebad4b0 100644
--- a/arch/arm/boot/dts/gemini-wbd222.dts
+++ b/arch/arm/boot/dts/gemini/gemini-wbd222.dts
@@ -10,7 +10,7 @@
 
 / {
 	model = "Wiliboard WBD-222";
-	compatible = "wiliboard,wbd222", "cortina,gemini";
+	compatible = "wiligear,wiliboard-wbd222", "cortina,gemini";
 	#address-cells = <1>;
 	#size-cells = <1>;
 
@@ -27,10 +27,10 @@
 	gpio_keys {
 		compatible = "gpio-keys";
 
-		button-setup {
+		button-reset {
 			debounce-interval = <100>;
 			wakeup-source;
-			linux,code = <KEY_SETUP>;
+			linux,code = <KEY_RESTART>;
 			label = "reset";
 			/* Conflict with ICE */
 			gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
@@ -91,33 +91,10 @@
 			/* 8MB of flash */
 			reg = <0x30000000 0x00800000>;
 
-			partition@0 {
-				label = "RedBoot";
-				reg = <0x00000000 0x00020000>;
-				read-only;
-			};
-			partition@20000 {
-				label = "kernel";
-				reg = <0x00020000 0x00100000>;
-			};
-			partition@120000 {
-				label = "rootfs";
-				reg = <0x00120000 0x006a0000>;
-			};
-			partition@7c0000 {
-				label = "VCTL";
-				reg = <0x007c0000 0x00010000>;
-				read-only;
-			};
-			partition@7d0000 {
-				label = "cfg";
-				reg = <0x007d0000 0x00010000>;
-				read-only;
-			};
-			partition@7e0000 {
-				label = "FIS";
-				reg = <0x007e0000 0x00010000>;
-				read-only;
+			partitions {
+				compatible = "redboot-fis";
+				/* Eraseblock at 0x7e0000 */
+				fis-index-block = <0x3f>;
 			};
 		};
 
diff --git a/arch/arm/boot/dts/gemini.dtsi b/arch/arm/boot/dts/gemini/gemini.dtsi
index e836bd0818d4..befe322bd7de 100644
--- a/arch/arm/boot/dts/gemini.dtsi
+++ b/arch/arm/boot/dts/gemini/gemini.dtsi
@@ -22,8 +22,6 @@
 			pinctrl-names = "default";
 			pinctrl-0 = <&pflash_default_pins>;
 			bank-width = <2>;
-			#address-cells = <1>;
-			#size-cells = <1>;
 			status = "disabled";
 		};
 
@@ -441,7 +439,7 @@
 		};
 
 		usb0: usb@68000000 {
-			compatible = "cortina,gemini-usb", "faraday,fotg210";
+			compatible = "cortina,gemini-usb", "faraday,fotg200";
 			reg = <0x68000000 0x1000>;
 			interrupts = <10 IRQ_TYPE_LEVEL_HIGH>;
 			resets = <&syscon GEMINI_RESET_USB0>;
@@ -457,12 +455,14 @@
 			 */
 			pinctrl-names = "default";
 			pinctrl-0 = <&usb_default_pins>;
+			/* Default to host mode */
+			dr_mode = "host";
 			syscon = <&syscon>;
 			status = "disabled";
 		};
 
 		usb1: usb@69000000 {
-			compatible = "cortina,gemini-usb", "faraday,fotg210";
+			compatible = "cortina,gemini-usb", "faraday,fotg200";
 			reg = <0x69000000 0x1000>;
 			interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
 			resets = <&syscon GEMINI_RESET_USB1>;
diff --git a/arch/arm/boot/dts/hisilicon/Makefile b/arch/arm/boot/dts/hisilicon/Makefile
new file mode 100644
index 000000000000..5ce0512c0010
--- /dev/null
+++ b/arch/arm/boot/dts/hisilicon/Makefile
@@ -0,0 +1,13 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_HI3xxx) += \
+	hi3620-hi4511.dtb
+dtb-$(CONFIG_ARCH_HIP01) += \
+	hip01-ca9x2.dtb
+dtb-$(CONFIG_ARCH_HIP04) += \
+	hip04-d01.dtb
+dtb-$(CONFIG_ARCH_HISI) += \
+	hi3519-demb.dtb
+dtb-$(CONFIG_ARCH_HIX5HD2) += \
+	hisi-x5hd2-dkb.dtb
+dtb-$(CONFIG_ARCH_SD5203) += \
+	sd5203.dtb
diff --git a/arch/arm/boot/dts/hi3519-demb.dts b/arch/arm/boot/dts/hisilicon/hi3519-demb.dts
index f473fa22e9ce..f473fa22e9ce 100644
--- a/arch/arm/boot/dts/hi3519-demb.dts
+++ b/arch/arm/boot/dts/hisilicon/hi3519-demb.dts
diff --git a/arch/arm/boot/dts/hi3519.dtsi b/arch/arm/boot/dts/hisilicon/hi3519.dtsi
index c524c854d319..a42b71cdc5d7 100644
--- a/arch/arm/boot/dts/hi3519.dtsi
+++ b/arch/arm/boot/dts/hisilicon/hi3519.dtsi
@@ -54,7 +54,7 @@
 			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&crg HI3519_UART0_CLK>, <&crg HI3519_UART0_CLK>;
 			clock-names = "uartclk", "apb_pclk";
-			status = "disable";
+			status = "disabled";
 		};
 
 		uart1: serial@12101000 {
@@ -63,7 +63,7 @@
 			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&crg HI3519_UART1_CLK>, <&crg HI3519_UART1_CLK>;
 			clock-names = "uartclk", "apb_pclk";
-			status = "disable";
+			status = "disabled";
 		};
 
 		uart2: serial@12102000 {
@@ -72,7 +72,7 @@
 			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&crg HI3519_UART2_CLK>, <&crg HI3519_UART2_CLK>;
 			clock-names = "uartclk", "apb_pclk";
-			status = "disable";
+			status = "disabled";
 		};
 
 		uart3: serial@12103000 {
@@ -81,7 +81,7 @@
 			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&crg HI3519_UART3_CLK>, <&crg HI3519_UART3_CLK>;
 			clock-names = "uartclk", "apb_pclk";
-			status = "disable";
+			status = "disabled";
 		};
 
 		uart4: serial@12104000 {
@@ -90,7 +90,7 @@
 			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&crg HI3519_UART4_CLK>, <&crg HI3519_UART4_CLK>;
 			clock-names = "uartclk", "apb_pclk";
-			status = "disable";
+			status = "disabled";
 		};
 
 		dual_timer0: timer@12000000 {
@@ -100,7 +100,7 @@
 			reg = <0x12000000 0x1000>;
 			clocks = <&clk_3m>;
 			clock-names = "apb_pclk";
-			status = "disable";
+			status = "disabled";
 		};
 
 		dual_timer1: timer@12001000 {
@@ -110,7 +110,7 @@
 			reg = <0x12001000 0x1000>;
 			clocks = <&clk_3m>;
 			clock-names = "apb_pclk";
-			status = "disable";
+			status = "disabled";
 		};
 
 		dual_timer2: timer@12002000 {
@@ -120,7 +120,7 @@
 			reg = <0x12002000 0x1000>;
 			clocks = <&clk_3m>;
 			clock-names = "apb_pclk";
-			status = "disable";
+			status = "disabled";
 		};
 
 		spi_bus0: spi@12120000 {
@@ -132,7 +132,7 @@
 			num-cs = <1>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			status = "disable";
+			status = "disabled";
 		};
 
 		spi_bus1: spi@12121000 {
@@ -144,7 +144,7 @@
 			num-cs = <1>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			status = "disable";
+			status = "disabled";
 		};
 
 		spi_bus2: spi@12122000 {
@@ -156,7 +156,7 @@
 			num-cs = <1>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			status = "disable";
+			status = "disabled";
 		};
 
 		sysctrl: system-controller@12020000 {
diff --git a/arch/arm/boot/dts/hi3620-hi4511.dts b/arch/arm/boot/dts/hisilicon/hi3620-hi4511.dts
index ce356c469e1e..f1c816a1d7cf 100644
--- a/arch/arm/boot/dts/hi3620-hi4511.dts
+++ b/arch/arm/boot/dts/hisilicon/hi3620-hi4511.dts
@@ -24,161 +24,161 @@
 
 	amba-bus {
 		dual_timer0: dual_timer@800000 {
-			status = "ok";
+			status = "okay";
 		};
 
 		uart0: serial@b00000 {	/* console */
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&uart0_pmx_func &uart0_cfg_func>;
 			pinctrl-1 = <&uart0_pmx_idle &uart0_cfg_idle>;
-			status = "ok";
+			status = "okay";
 		};
 
 		uart1: serial@b01000 { /* modem */
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&uart1_pmx_func &uart1_cfg_func>;
 			pinctrl-1 = <&uart1_pmx_idle &uart1_cfg_idle>;
-			status = "ok";
+			status = "okay";
 		};
 
 		uart2: serial@b02000 { /* audience */
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&uart2_pmx_func &uart2_cfg_func>;
 			pinctrl-1 = <&uart2_pmx_idle &uart2_cfg_idle>;
-			status = "ok";
+			status = "okay";
 		};
 
 		uart3: serial@b03000 {
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&uart3_pmx_func &uart3_cfg_func>;
 			pinctrl-1 = <&uart3_pmx_idle &uart3_cfg_idle>;
-			status = "ok";
+			status = "okay";
 		};
 
 		uart4: serial@b04000 {
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&uart4_pmx_func &uart4_cfg_func>;
 			pinctrl-1 = <&uart4_pmx_idle &uart4_cfg_func>;
-			status = "ok";
+			status = "okay";
 		};
 
 		pmx0: pinmux@803000 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&board_pmx_pins>;
 
-			board_pmx_pins: board_pmx_pins {
+			board_pmx_pins: board-pins {
 				pinctrl-single,pins = <
 					0x008 0x0	/* GPIO -- eFUSE_DOUT */
 					0x100 0x0	/* USIM_CLK & USIM_DATA (IOMG63) */
 				>;
 			};
-			uart0_pmx_func: uart0_pmx_func {
+			uart0_pmx_func: uart0-pins {
 				pinctrl-single,pins = <
 					0x0f0 0x0
 					0x0f4 0x0	/* UART0_RX & UART0_TX */
 				>;
 			};
-			uart0_pmx_idle: uart0_pmx_idle {
+			uart0_pmx_idle: uart0-idle-pins {
 				pinctrl-single,pins = <
 					/*0x0f0 0x1*/	/* UART0_CTS & UART0_RTS */
 					0x0f4 0x1	/* UART0_RX & UART0_TX */
 				>;
 			};
-			uart1_pmx_func: uart1_pmx_func {
+			uart1_pmx_func: uart1-pins {
 				pinctrl-single,pins = <
 					0x0f8 0x0	/* UART1_CTS & UART1_RTS (IOMG61) */
 					0x0fc 0x0	/* UART1_RX & UART1_TX (IOMG62) */
 				>;
 			};
-			uart1_pmx_idle: uart1_pmx_idle {
+			uart1_pmx_idle: uart1-idle-pins {
 				pinctrl-single,pins = <
 					0x0f8 0x1	/* GPIO (IOMG61) */
 					0x0fc 0x1	/* GPIO (IOMG62) */
 				>;
 			};
-			uart2_pmx_func: uart2_pmx_func {
+			uart2_pmx_func: uart2-pins {
 				pinctrl-single,pins = <
 					0x104 0x2	/* UART2_RXD (IOMG96) */
 					0x108 0x2	/* UART2_TXD (IOMG64) */
 				>;
 			};
-			uart2_pmx_idle: uart2_pmx_idle {
+			uart2_pmx_idle: uart2-idle-pins {
 				pinctrl-single,pins = <
 					0x104 0x1	/* GPIO (IOMG96) */
 					0x108 0x1	/* GPIO (IOMG64) */
 				>;
 			};
-			uart3_pmx_func: uart3_pmx_func {
+			uart3_pmx_func: uart3-pins {
 				pinctrl-single,pins = <
 					0x160 0x2	/* UART3_CTS & UART3_RTS (IOMG85) */
 					0x164 0x2	/* UART3_RXD & UART3_TXD (IOMG86) */
 				>;
 			};
-			uart3_pmx_idle: uart3_pmx_idle {
+			uart3_pmx_idle: uart3-idle-pins {
 				pinctrl-single,pins = <
 					0x160 0x1	/* GPIO (IOMG85) */
 					0x164 0x1	/* GPIO (IOMG86) */
 				>;
 			};
-			uart4_pmx_func: uart4_pmx_func {
+			uart4_pmx_func: uart4-pins {
 				pinctrl-single,pins = <
 					0x168 0x0	/* UART4_CTS & UART4_RTS (IOMG87) */
 					0x16c 0x0	/* UART4_RXD (IOMG88) */
 					0x170 0x0	/* UART4_TXD (IOMG93) */
 				>;
 			};
-			uart4_pmx_idle: uart4_pmx_idle {
+			uart4_pmx_idle: uart4-idle-pins {
 				pinctrl-single,pins = <
 					0x168 0x1	/* GPIO (IOMG87) */
 					0x16c 0x1	/* GPIO (IOMG88) */
 					0x170 0x1	/* GPIO (IOMG93) */
 				>;
 			};
-			i2c0_pmx_func: i2c0_pmx_func {
+			i2c0_pmx_func: i2c0-pins {
 				pinctrl-single,pins = <
 					0x0b4 0x0	/* I2C0_SCL & I2C0_SDA (IOMG45) */
 				>;
 			};
-			i2c0_pmx_idle: i2c0_pmx_idle {
+			i2c0_pmx_idle: i2c0-idle-pins {
 				pinctrl-single,pins = <
 					0x0b4 0x1	/* GPIO (IOMG45) */
 				>;
 			};
-			i2c1_pmx_func: i2c1_pmx_func {
+			i2c1_pmx_func: i2c1-pins {
 				pinctrl-single,pins = <
 					0x0b8 0x0	/* I2C1_SCL & I2C1_SDA (IOMG46) */
 				>;
 			};
-			i2c1_pmx_idle: i2c1_pmx_idle {
+			i2c1_pmx_idle: i2c1-idle-pins {
 				pinctrl-single,pins = <
 					0x0b8 0x1	/* GPIO (IOMG46) */
 				>;
 			};
-			i2c2_pmx_func: i2c2_pmx_func {
+			i2c2_pmx_func: i2c2-pins {
 				pinctrl-single,pins = <
 					0x068 0x0	/* I2C2_SCL (IOMG26) */
 					0x06c 0x0	/* I2C2_SDA (IOMG27) */
 				>;
 			};
-			i2c2_pmx_idle: i2c2_pmx_idle {
+			i2c2_pmx_idle: i2c2-idle-pins {
 				pinctrl-single,pins = <
 					0x068 0x1	/* GPIO (IOMG26) */
 					0x06c 0x1	/* GPIO (IOMG27) */
 				>;
 			};
-			i2c3_pmx_func: i2c3_pmx_func {
+			i2c3_pmx_func: i2c3-pins {
 				pinctrl-single,pins = <
 					0x050 0x2	/* I2C3_SCL (IOMG20) */
 					0x054 0x2	/* I2C3_SDA (IOMG21) */
 				>;
 			};
-			i2c3_pmx_idle: i2c3_pmx_idle {
+			i2c3_pmx_idle: i2c3-idle-pins {
 				pinctrl-single,pins = <
 					0x050 0x1	/* GPIO (IOMG20) */
 					0x054 0x1	/* GPIO (IOMG21) */
 				>;
 			};
-			spi0_pmx_func: spi0_pmx_func {
+			spi0_pmx_func: spi0-pins {
 				pinctrl-single,pins = <
 					0x0d4 0x0	/* SPI0_CLK/SPI0_DI/SPI0_DO (IOMG53) */
 					0x0d8 0x0	/* SPI0_CS0 (IOMG54) */
@@ -187,7 +187,7 @@
 					0x0e4 0x0	/* SPI0_CS3 (IOMG57) */
 				>;
 			};
-			spi0_pmx_idle: spi0_pmx_idle {
+			spi0_pmx_idle: spi0-idle-pins {
 				pinctrl-single,pins = <
 					0x0d4 0x1	/* GPIO (IOMG53) */
 					0x0d8 0x1	/* GPIO (IOMG54) */
@@ -196,21 +196,21 @@
 					0x0e4 0x1	/* GPIO (IOMG57) */
 				>;
 			};
-			spi1_pmx_func: spi1_pmx_func {
+			spi1_pmx_func: spi1-pins {
 				pinctrl-single,pins = <
 					0x184 0x0	/* SPI1_CLK/SPI1_DI (IOMG98) */
 					0x0e8 0x0	/* SPI1_DO (IOMG58) */
 					0x0ec 0x0	/* SPI1_CS (IOMG95) */
 				>;
 			};
-			spi1_pmx_idle: spi1_pmx_idle {
+			spi1_pmx_idle: spi1-idle-pins {
 				pinctrl-single,pins = <
 					0x184 0x1	/* GPIO (IOMG98) */
 					0x0e8 0x1	/* GPIO (IOMG58) */
 					0x0ec 0x1	/* GPIO (IOMG95) */
 				>;
 			};
-			kpc_pmx_func: kpc_pmx_func {
+			kpc_pmx_func: kpc-pins {
 				pinctrl-single,pins = <
 					0x12c 0x0	/* KEY_IN0 (IOMG73) */
 					0x130 0x0	/* KEY_IN1 (IOMG74) */
@@ -220,7 +220,7 @@
 					0x114 0x0	/* KEY_OUT2 (IOMG67) */
 				>;
 			};
-			kpc_pmx_idle: kpc_pmx_idle {
+			kpc_pmx_idle: kpc-idle-pins {
 				pinctrl-single,pins = <
 					0x12c 0x1	/* GPIO (IOMG73) */
 					0x130 0x1	/* GPIO (IOMG74) */
@@ -230,13 +230,13 @@
 					0x114 0x1	/* GPIO (IOMG67) */
 				>;
 			};
-			gpio_key_func: gpio_key_func {
+			gpio_key_func: gpio-key-pins {
 				pinctrl-single,pins = <
 					0x10c 0x1	/* KEY_OUT0/GPIO (IOMG65) */
 					0x130 0x1	/* KEY_IN1/GPIO (IOMG74) */
 				>;
 			};
-			emmc_pmx_func: emmc_pmx_func {
+			emmc_pmx_func: emmc-pins {
 				pinctrl-single,pins = <
 					0x030 0x2	/* eMMC_CMD/eMMC_CLK (IOMG12) */
 					0x018 0x0	/* NAND_CS3_N (IOMG6) */
@@ -245,7 +245,7 @@
 					0x02c 0x2	/* eMMC_DATA[0:7] (IOMG10) */
 				>;
 			};
-			emmc_pmx_idle: emmc_pmx_idle {
+			emmc_pmx_idle: emmc-idle-pins {
 				pinctrl-single,pins = <
 					0x030 0x0	/* GPIO (IOMG12) */
 					0x018 0x1	/* GPIO (IOMG6) */
@@ -254,19 +254,19 @@
 					0x02c 0x1	/* GPIO (IOMG10) */
 				>;
 			};
-			sd_pmx_func: sd_pmx_func {
+			sd_pmx_func: sd-pins {
 				pinctrl-single,pins = <
 					0x0bc 0x0	/* SD_CLK/SD_CMD/SD_DATA0/SD_DATA1/SD_DATA2 (IOMG47) */
 					0x0c0 0x0	/* SD_DATA3 (IOMG48) */
 				>;
 			};
-			sd_pmx_idle: sd_pmx_idle {
+			sd_pmx_idle: sd-idle-pins {
 				pinctrl-single,pins = <
 					0x0bc 0x1	/* GPIO (IOMG47) */
 					0x0c0 0x1	/* GPIO (IOMG48) */
 				>;
 			};
-			nand_pmx_func: nand_pmx_func {
+			nand_pmx_func: nand-pins {
 				pinctrl-single,pins = <
 					0x00c 0x0	/* NAND_ALE/NAND_CLE/.../NAND_DATA[0:7] (IOMG3) */
 					0x010 0x0	/* NAND_CS1_N (IOMG4) */
@@ -279,7 +279,7 @@
 					0x02c 0x0	/* NAND_DATA[8:15] (IOMG10) */
 				>;
 			};
-			nand_pmx_idle: nand_pmx_idle {
+			nand_pmx_idle: nand-idle-pins {
 				pinctrl-single,pins = <
 					0x00c 0x1	/* GPIO (IOMG3) */
 					0x010 0x1	/* GPIO (IOMG4) */
@@ -292,17 +292,17 @@
 					0x02c 0x1	/* GPIO (IOMG10) */
 				>;
 			};
-			sdio_pmx_func: sdio_pmx_func {
+			sdio_pmx_func: sdio-pins {
 				pinctrl-single,pins = <
 					0x0c4 0x0	/* SDIO_CLK/SDIO_CMD/SDIO_DATA[0:3] (IOMG49) */
 				>;
 			};
-			sdio_pmx_idle: sdio_pmx_idle {
+			sdio_pmx_idle: sdio-idle-pins {
 				pinctrl-single,pins = <
 					0x0c4 0x1	/* GPIO (IOMG49) */
 				>;
 			};
-			audio_out_pmx_func: audio_out_pmx_func {
+			audio_out_pmx_func: audio-out-pins {
 				pinctrl-single,pins = <
 					0x0f0 0x1	/* GPIO (IOMG59), audio spk & earphone */
 				>;
@@ -314,7 +314,7 @@
 			pinctrl-0 = <	&board_pu_pins &board_pd_pins &board_pd_ps_pins
 					&board_np_pins &board_ps_pins &kpc_cfg_func
 					&audio_out_cfg_func>;
-			board_pu_pins: board_pu_pins {
+			board_pu_pins: board-pu-pins {
 				pinctrl-single,pins = <
 					0x014 0		/* GPIO_158 (IOCFG2) */
 					0x018 0		/* GPIO_159 (IOCFG3) */
@@ -324,7 +324,7 @@
 				pinctrl-single,bias-pulldown = <0 2 0 2>;
 				pinctrl-single,bias-pullup = <1 1 0 1>;
 			};
-			board_pd_pins: board_pd_pins {
+			board_pd_pins: board-pd-pins {
 				pinctrl-single,pins = <
 					0x038 0		/* eFUSE_DOUT (IOCFG11) */
 					0x150 0		/* ISP_GPIO8 (IOCFG93) */
@@ -333,7 +333,7 @@
 				pinctrl-single,bias-pulldown = <2 2 0 2>;
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 			};
-			board_pd_ps_pins: board_pd_ps_pins {
+			board_pd_ps_pins: board-pd-ps-pins {
 				pinctrl-single,pins = <
 					0x2d8 0		/* CLK_OUT0 (IOCFG190) */
 					0x004 0		/* PMU_SPI_DATA (IOCFG192) */
@@ -342,21 +342,21 @@
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			board_np_pins: board_np_pins {
+			board_np_pins: board-np-pins {
 				pinctrl-single,pins = <
 					0x24c 0		/* KEYPAD_OUT7 (IOCFG155) */
 				>;
 				pinctrl-single,bias-pulldown = <0 2 0 2>;
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 			};
-			board_ps_pins: board_ps_pins {
+			board_ps_pins: board-ps-pins {
 				pinctrl-single,pins = <
 					0x000 0		/* PMU_SPI_CLK (IOCFG191) */
 					0x008 0		/* PMU_SPI_CS_N (IOCFG193) */
 				>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			uart0_cfg_func: uart0_cfg_func {
+			uart0_cfg_func: uart0-cfg-pins {
 				pinctrl-single,pins = <
 					0x208 0		/* UART0_RXD (IOCFG138) */
 					0x20c 0		/* UART0_TXD (IOCFG139) */
@@ -364,7 +364,7 @@
 				pinctrl-single,bias-pulldown = <0 2 0 2>;
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 			};
-			uart0_cfg_idle: uart0_cfg_idle {
+			uart0_cfg_idle: uart0-cfg-idle-pins {
 				pinctrl-single,pins = <
 					0x208 0		/* UART0_RXD (IOCFG138) */
 					0x20c 0		/* UART0_TXD (IOCFG139) */
@@ -372,7 +372,7 @@
 				pinctrl-single,bias-pulldown = <2 2 0 2>;
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 			};
-			uart1_cfg_func: uart1_cfg_func {
+			uart1_cfg_func: uart1-cfg-pins {
 				pinctrl-single,pins = <
 					0x210 0		/* UART1_CTS (IOCFG140) */
 					0x214 0		/* UART1_RTS (IOCFG141) */
@@ -382,7 +382,7 @@
 				pinctrl-single,bias-pulldown = <0 2 0 2>;
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 			};
-			uart1_cfg_idle: uart1_cfg_idle {
+			uart1_cfg_idle: uart1-cfg-idle-pins {
 				pinctrl-single,pins = <
 					0x210 0		/* UART1_CTS (IOCFG140) */
 					0x214 0		/* UART1_RTS (IOCFG141) */
@@ -392,7 +392,7 @@
 				pinctrl-single,bias-pulldown = <2 2 0 2>;
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 			};
-			uart2_cfg_func: uart2_cfg_func {
+			uart2_cfg_func: uart2-cfg-pins {
 				pinctrl-single,pins = <
 					0x220 0		/* UART2_CTS (IOCFG144) */
 					0x224 0		/* UART2_RTS (IOCFG145) */
@@ -402,7 +402,7 @@
 				pinctrl-single,bias-pulldown = <0 2 0 2>;
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 			};
-			uart2_cfg_idle: uart2_cfg_idle {
+			uart2_cfg_idle: uart2-cfg-idle-pins {
 				pinctrl-single,pins = <
 					0x220 0		/* GPIO (IOCFG144) */
 					0x224 0		/* GPIO (IOCFG145) */
@@ -412,7 +412,7 @@
 				pinctrl-single,bias-pulldown = <2 2 0 2>;
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 			};
-			uart3_cfg_func: uart3_cfg_func {
+			uart3_cfg_func: uart3-cfg-pins {
 				pinctrl-single,pins = <
 					0x294 0		/* UART3_CTS (IOCFG173) */
 					0x298 0		/* UART3_RTS (IOCFG174) */
@@ -422,7 +422,7 @@
 				pinctrl-single,bias-pulldown = <0 2 0 2>;
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 			};
-			uart3_cfg_idle: uart3_cfg_idle {
+			uart3_cfg_idle: uart3-cfg-idle-pins {
 				pinctrl-single,pins = <
 					0x294 0		/* UART3_CTS (IOCFG173) */
 					0x298 0		/* UART3_RTS (IOCFG174) */
@@ -432,7 +432,7 @@
 				pinctrl-single,bias-pulldown = <2 2 0 2>;
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 			};
-			uart4_cfg_func: uart4_cfg_func {
+			uart4_cfg_func: uart4-cfg-pins {
 				pinctrl-single,pins = <
 					0x2a4 0		/* UART4_CTS (IOCFG177) */
 					0x2a8 0		/* UART4_RTS (IOCFG178) */
@@ -442,7 +442,7 @@
 				pinctrl-single,bias-pulldown = <0 2 0 2>;
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 			};
-			i2c0_cfg_func: i2c0_cfg_func {
+			i2c0_cfg_func: i2c0-cfg-pins {
 				pinctrl-single,pins = <
 					0x17c 0		/* I2C0_SCL (IOCFG103) */
 					0x180 0		/* I2C0_SDA (IOCFG104) */
@@ -451,7 +451,7 @@
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			i2c1_cfg_func: i2c1_cfg_func {
+			i2c1_cfg_func: i2c1-cfg-pins {
 				pinctrl-single,pins = <
 					0x184 0		/* I2C1_SCL (IOCFG105) */
 					0x188 0		/* I2C1_SDA (IOCFG106) */
@@ -460,7 +460,7 @@
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			i2c2_cfg_func: i2c2_cfg_func {
+			i2c2_cfg_func: i2c2-cfg-pins {
 				pinctrl-single,pins = <
 					0x118 0		/* I2C2_SCL (IOCFG79) */
 					0x11c 0		/* I2C2_SDA (IOCFG80) */
@@ -469,7 +469,7 @@
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			i2c3_cfg_func: i2c3_cfg_func {
+			i2c3_cfg_func: i2c3-cfg-pins {
 				pinctrl-single,pins = <
 					0x100 0		/* I2C3_SCL (IOCFG73) */
 					0x104 0		/* I2C3_SDA (IOCFG74) */
@@ -478,7 +478,7 @@
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			spi0_cfg_func1: spi0_cfg_func1 {
+			spi0_cfg_func1: spi0-cfg-func1-pins {
 				pinctrl-single,pins = <
 					0x1d4 0		/* SPI0_CLK (IOCFG125) */
 					0x1d8 0		/* SPI0_DI (IOCFG126) */
@@ -488,7 +488,7 @@
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			spi0_cfg_func2: spi0_cfg_func2 {
+			spi0_cfg_func2: spi0-cfg-func2-pins {
 				pinctrl-single,pins = <
 					0x1e0 0		/* SPI0_CS0 (IOCFG128) */
 					0x1e4 0		/* SPI0_CS1 (IOCFG129) */
@@ -499,7 +499,7 @@
 				pinctrl-single,bias-pullup = <1 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			spi1_cfg_func1: spi1_cfg_func1 {
+			spi1_cfg_func1: spi1-cfg-func1-pins {
 				pinctrl-single,pins = <
 					0x1f0 0		/* SPI1_CLK (IOCFG132) */
 					0x1f4 0		/* SPI1_DI (IOCFG133) */
@@ -509,7 +509,7 @@
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			spi1_cfg_func2: spi1_cfg_func2 {
+			spi1_cfg_func2: spi1-cfg-func2-pins {
 				pinctrl-single,pins = <
 					0x1fc 0		/* SPI1_CS (IOCFG135) */
 				>;
@@ -517,7 +517,7 @@
 				pinctrl-single,bias-pullup = <1 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			kpc_cfg_func: kpc_cfg_func {
+			kpc_cfg_func: kpc-cfg-pins {
 				pinctrl-single,pins = <
 					0x250 0		/* KEY_IN0 (IOCFG156) */
 					0x254 0		/* KEY_IN1 (IOCFG157) */
@@ -529,7 +529,7 @@
 				pinctrl-single,bias-pulldown = <2 2 0 2>;
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 			};
-			emmc_cfg_func: emmc_cfg_func {
+			emmc_cfg_func: emmc-cfg-pins {
 				pinctrl-single,pins = <
 					0x0ac 0		/* eMMC_CMD (IOCFG40) */
 					0x0b0 0		/* eMMC_CLK (IOCFG41) */
@@ -549,7 +549,7 @@
 				pinctrl-single,bias-pullup = <1 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			sd_cfg_func1: sd_cfg_func1 {
+			sd_cfg_func1: sd-cfg-func1-pins {
 				pinctrl-single,pins = <
 					0x18c 0		/* SD_CLK (IOCFG107) */
 					0x190 0		/* SD_CMD (IOCFG108) */
@@ -558,7 +558,7 @@
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			sd_cfg_func2: sd_cfg_func2 {
+			sd_cfg_func2: sd-cfg-func2-pins {
 				pinctrl-single,pins = <
 					0x194 0		/* SD_DATA0 (IOCFG109) */
 					0x198 0		/* SD_DATA1 (IOCFG110) */
@@ -569,7 +569,7 @@
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 				pinctrl-single,drive-strength = <0x70 0xf0>;
 			};
-			nand_cfg_func1: nand_cfg_func1 {
+			nand_cfg_func1: nand-cfg-func1-pins {
 				pinctrl-single,pins = <
 					0x03c 0		/* NAND_ALE (IOCFG12) */
 					0x040 0		/* NAND_CLE (IOCFG13) */
@@ -594,7 +594,7 @@
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			nand_cfg_func2: nand_cfg_func2 {
+			nand_cfg_func2: nand-cfg-func2-pins {
 				pinctrl-single,pins = <
 					0x044 0		/* NAND_RE_N (IOCFG14) */
 					0x048 0		/* NAND_WE_N (IOCFG15) */
@@ -611,7 +611,7 @@
 				pinctrl-single,bias-pullup = <1 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			sdio_cfg_func: sdio_cfg_func {
+			sdio_cfg_func: sdio-cfg-pins {
 				pinctrl-single,pins = <
 					0x1a4 0		/* SDIO0_CLK (IOCG113) */
 					0x1a8 0		/* SDIO0_CMD (IOCG114) */
@@ -624,7 +624,7 @@
 				pinctrl-single,bias-pullup = <0 1 0 1>;
 				pinctrl-single,drive-strength = <0x30 0xf0>;
 			};
-			audio_out_cfg_func: audio_out_cfg_func {
+			audio_out_cfg_func: audio-out-cfg-pins {
 				pinctrl-single,pins = <
 					0x200 0		/* GPIO (IOCFG136) */
 					0x204 0		/* GPIO (IOCFG137) */
diff --git a/arch/arm/boot/dts/hi3620.dtsi b/arch/arm/boot/dts/hisilicon/hi3620.dtsi
index cf48ec14af43..a254ec009296 100644
--- a/arch/arm/boot/dts/hi3620.dtsi
+++ b/arch/arm/boot/dts/hisilicon/hi3620.dtsi
@@ -545,10 +545,9 @@
 			compatible = "pinctrl-single";
 			reg = <0x803000 0x188>;
 			#address-cells = <1>;
-			#size-cells = <1>;
+			#size-cells = <0>;
 			#pinctrl-cells = <1>;
 			#gpio-range-cells = <3>;
-			ranges;
 
 			pinctrl-single,register-width = <32>;
 			pinctrl-single,function-mask = <7>;
@@ -567,9 +566,8 @@
 			compatible = "pinconf-single";
 			reg = <0x803800 0x2dc>;
 			#address-cells = <1>;
-			#size-cells = <1>;
+			#size-cells = <0>;
 			#pinctrl-cells = <1>;
-			ranges;
 
 			pinctrl-single,register-width = <32>;
 		};
diff --git a/arch/arm/boot/dts/hip01-ca9x2.dts b/arch/arm/boot/dts/hisilicon/hip01-ca9x2.dts
index f3faf247cd61..f3faf247cd61 100644
--- a/arch/arm/boot/dts/hip01-ca9x2.dts
+++ b/arch/arm/boot/dts/hisilicon/hip01-ca9x2.dts
diff --git a/arch/arm/boot/dts/hip01.dtsi b/arch/arm/boot/dts/hisilicon/hip01.dtsi
index e17f36bd9006..e17f36bd9006 100644
--- a/arch/arm/boot/dts/hip01.dtsi
+++ b/arch/arm/boot/dts/hisilicon/hip01.dtsi
diff --git a/arch/arm/boot/dts/hip04-d01.dts b/arch/arm/boot/dts/hisilicon/hip04-d01.dts
index f5691dbc26d2..0210064bf6a5 100644
--- a/arch/arm/boot/dts/hip04-d01.dts
+++ b/arch/arm/boot/dts/hisilicon/hip04-d01.dts
@@ -23,7 +23,7 @@
 
 	soc {
 		uart0: serial@4007000 {
-			status = "ok";
+			status = "okay";
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/hip04.dtsi b/arch/arm/boot/dts/hisilicon/hip04.dtsi
index 2424cc545c9c..2424cc545c9c 100644
--- a/arch/arm/boot/dts/hip04.dtsi
+++ b/arch/arm/boot/dts/hisilicon/hip04.dtsi
diff --git a/arch/arm/boot/dts/hisi-x5hd2-dkb.dts b/arch/arm/boot/dts/hisilicon/hisi-x5hd2-dkb.dts
index 7758c19038f0..7758c19038f0 100644
--- a/arch/arm/boot/dts/hisi-x5hd2-dkb.dts
+++ b/arch/arm/boot/dts/hisilicon/hisi-x5hd2-dkb.dts
diff --git a/arch/arm/boot/dts/hisi-x5hd2.dtsi b/arch/arm/boot/dts/hisilicon/hisi-x5hd2.dtsi
index dc991ba2a9fb..dc991ba2a9fb 100644
--- a/arch/arm/boot/dts/hisi-x5hd2.dtsi
+++ b/arch/arm/boot/dts/hisilicon/hisi-x5hd2.dtsi
diff --git a/arch/arm/boot/dts/sd5203.dts b/arch/arm/boot/dts/hisilicon/sd5203.dts
index a61a078ea042..69381819e07b 100644
--- a/arch/arm/boot/dts/sd5203.dts
+++ b/arch/arm/boot/dts/hisilicon/sd5203.dts
@@ -15,7 +15,7 @@
 	#size-cells = <1>;
 
 	chosen {
-		bootargs="console=ttyS0,9600 earlycon=uart8250,mmio32,0x1600d000";
+		bootargs = "console=ttyS0,9600 earlycon=uart8250,mmio32,0x1600d000";
 	};
 
 	aliases {
diff --git a/arch/arm/boot/dts/hpe/Makefile b/arch/arm/boot/dts/hpe/Makefile
new file mode 100644
index 000000000000..e175b1732cdb
--- /dev/null
+++ b/arch/arm/boot/dts/hpe/Makefile
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_HPE_GXP) += \
+	hpe-bmc-dl360gen10.dtb
diff --git a/arch/arm/boot/dts/hpe/hpe-bmc-dl360gen10.dts b/arch/arm/boot/dts/hpe/hpe-bmc-dl360gen10.dts
new file mode 100644
index 000000000000..3a7382ce40ef
--- /dev/null
+++ b/arch/arm/boot/dts/hpe/hpe-bmc-dl360gen10.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for HPE DL360Gen10
+ */
+
+/include/ "hpe-gxp.dtsi"
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "hpe,gxp-dl360gen10", "hpe,gxp";
+	model = "Hewlett Packard Enterprise ProLiant dl360 Gen10";
+
+	aliases {
+		serial0 = &uartc;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x20000000>;
+	};
+};
diff --git a/arch/arm/boot/dts/hpe/hpe-gxp.dtsi b/arch/arm/boot/dts/hpe/hpe-gxp.dtsi
new file mode 100644
index 000000000000..cf735b3c4f35
--- /dev/null
+++ b/arch/arm/boot/dts/hpe/hpe-gxp.dtsi
@@ -0,0 +1,127 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for HPE GXP
+ */
+
+/dts-v1/;
+/ {
+	model = "Hewlett Packard Enterprise GXP BMC";
+	compatible = "hpe,gxp";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "arm,cortex-a9";
+			reg = <0>;
+			device_type = "cpu";
+			next-level-cache = <&L2>;
+		};
+	};
+
+	clocks {
+		pll: clock-0 {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <1600000000>;
+		};
+
+		iopclk: clock-1 {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clock-div = <4>;
+			clock-mult = <1>;
+			clocks = <&pll>;
+		};
+	};
+
+	axi {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		dma-ranges;
+
+		L2: cache-controller@b0040000 {
+			compatible = "arm,pl310-cache";
+			reg = <0xb0040000 0x1000>;
+			cache-unified;
+			cache-level = <2>;
+		};
+
+		ahb@c0000000 {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xc0000000 0x30000000>;
+			dma-ranges;
+
+			vic0: interrupt-controller@eff0000 {
+				compatible = "arm,pl192-vic";
+				reg = <0xeff0000 0x1000>;
+				interrupt-controller;
+				#interrupt-cells = <1>;
+			};
+
+			vic1: interrupt-controller@80f00000 {
+				compatible = "arm,pl192-vic";
+				reg = <0x80f00000 0x1000>;
+				interrupt-controller;
+				#interrupt-cells = <1>;
+			};
+
+			uarta: serial@e0 {
+				compatible = "ns16550a";
+				reg = <0xe0 0x8>;
+				interrupts = <17>;
+				interrupt-parent = <&vic0>;
+				clock-frequency = <1846153>;
+				reg-shift = <0>;
+			};
+
+			uartb: serial@e8 {
+				compatible = "ns16550a";
+				reg = <0xe8 0x8>;
+				interrupts = <18>;
+				interrupt-parent = <&vic0>;
+				clock-frequency = <1846153>;
+				reg-shift = <0>;
+			};
+
+			uartc: serial@f0 {
+				compatible = "ns16550a";
+				reg = <0xf0 0x8>;
+				interrupts = <19>;
+				interrupt-parent = <&vic0>;
+				clock-frequency = <1846153>;
+				reg-shift = <0>;
+			};
+
+			usb0: usb@efe0000 {
+				compatible = "hpe,gxp-ehci", "generic-ehci";
+				reg = <0xefe0000 0x100>;
+				interrupts = <7>;
+				interrupt-parent = <&vic0>;
+			};
+
+			st: timer@80 {
+				compatible = "hpe,gxp-timer";
+				reg = <0x80 0x16>;
+				interrupts = <0>;
+				interrupt-parent = <&vic0>;
+				clocks = <&iopclk>;
+				clock-names = "iop";
+			};
+
+			usb1: usb@efe0100 {
+				compatible = "hpe,gxp-ohci", "generic-ohci";
+				reg = <0xefe0100 0x110>;
+				interrupts = <6>;
+				interrupt-parent = <&vic0>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/imx25-karo-tx25.dts b/arch/arm/boot/dts/imx25-karo-tx25.dts
deleted file mode 100644
index 0950eb66d3d9..000000000000
--- a/arch/arm/boot/dts/imx25-karo-tx25.dts
+++ /dev/null
@@ -1,108 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2012 Sascha Hauer, Pengutronix
- */
-
-/dts-v1/;
-#include "imx25.dtsi"
-
-/ {
-	model = "Ka-Ro TX25";
-	compatible = "karo,imx25-tx25", "fsl,imx25";
-
-	chosen {
-		stdout-path = &uart1;
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_fec_phy: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "fec-phy";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio4 9 0>;
-			enable-active-high;
-		};
-	};
-
-	memory@80000000 {
-		device_type = "memory";
-		reg = <0x80000000 0x02000000 0x90000000 0x02000000>;
-	};
-};
-
-&iomuxc {
-	pinctrl_uart1: uart1grp {
-		fsl,pins = <
-			MX25_PAD_UART1_TXD__UART1_TXD 0x80000000
-			MX25_PAD_UART1_RXD__UART1_RXD 0x80000000
-			MX25_PAD_UART1_CTS__UART1_CTS 0x80000000
-			MX25_PAD_UART1_RTS__UART1_RTS 0x80000000
-		>;
-	};
-
-	pinctrl_fec: fecgrp {
-		fsl,pins = <
-			MX25_PAD_D11__GPIO_4_9		0x80000000 /* FEC PHY power on pin */
-			MX25_PAD_D13__GPIO_4_7		0x80000000 /* FEC reset */
-			MX25_PAD_FEC_MDC__FEC_MDC	0x80000000
-			MX25_PAD_FEC_MDIO__FEC_MDIO	0x80000000
-			MX25_PAD_FEC_TDATA0__FEC_TDATA0	0x80000000
-			MX25_PAD_FEC_TDATA1__FEC_TDATA1	0x80000000
-			MX25_PAD_FEC_TX_EN__FEC_TX_EN	0x80000000
-			MX25_PAD_FEC_RDATA0__FEC_RDATA0	0x80000000
-			MX25_PAD_FEC_RDATA1__FEC_RDATA1	0x80000000
-			MX25_PAD_FEC_RX_DV__FEC_RX_DV	0x80000000
-			MX25_PAD_FEC_TX_CLK__FEC_TX_CLK	0x80000000
-		>;
-	};
-
-	pinctrl_nfc: nfcgrp {
-		fsl,pins = <
-			MX25_PAD_NF_CE0__NF_CE0		0x80000000
-			MX25_PAD_NFWE_B__NFWE_B		0x80000000
-			MX25_PAD_NFRE_B__NFRE_B		0x80000000
-			MX25_PAD_NFALE__NFALE		0x80000000
-			MX25_PAD_NFCLE__NFCLE		0x80000000
-			MX25_PAD_NFWP_B__NFWP_B		0x80000000
-			MX25_PAD_NFRB__NFRB		0x80000000
-			MX25_PAD_D7__D7			0x80000000
-			MX25_PAD_D6__D6			0x80000000
-			MX25_PAD_D5__D5			0x80000000
-			MX25_PAD_D4__D4			0x80000000
-			MX25_PAD_D3__D3			0x80000000
-			MX25_PAD_D2__D2			0x80000000
-			MX25_PAD_D1__D1			0x80000000
-			MX25_PAD_D0__D0			0x80000000
-		>;
-	};
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
-	status = "okay";
-};
-
-&fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_fec>;
-	phy-reset-gpios = <&gpio3 7 GPIO_ACTIVE_LOW>;
-	phy-mode = "rmii";
-	phy-supply = <&reg_fec_phy>;
-	status = "okay";
-};
-
-&nfc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_nfc>;
-	nand-on-flash-bbt;
-	nand-ecc-mode = "hw";
-	nand-bus-width = <8>;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx28-apf28.dts b/arch/arm/boot/dts/imx28-apf28.dts
deleted file mode 100644
index 14a92fe59770..000000000000
--- a/arch/arm/boot/dts/imx28-apf28.dts
+++ /dev/null
@@ -1,80 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2012 Armadeus Systems - <support@armadeus.com>
- */
-
-/dts-v1/;
-#include "imx28.dtsi"
-
-/ {
-	model = "Armadeus Systems APF28 module";
-	compatible = "armadeus,imx28-apf28", "fsl,imx28";
-
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			nand-controller@8000c000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
-				status = "okay";
-
-				partition@0 {
-					label = "u-boot";
-					reg = <0x0 0x300000>;
-				};
-
-				partition@300000 {
-					label = "env";
-					reg = <0x300000 0x80000>;
-				};
-
-				partition@380000 {
-					label = "env2";
-					reg = <0x380000 0x80000>;
-				};
-
-				partition@400000 {
-					label = "dtb";
-					reg = <0x400000 0x80000>;
-				};
-
-				partition@480000 {
-					label = "splash";
-					reg = <0x480000 0x80000>;
-				};
-
-				partition@500000 {
-					label = "kernel";
-					reg = <0x500000 0x800000>;
-				};
-
-				partition@d00000 {
-					label = "rootfs";
-					reg = <0xd00000 0xf300000>;
-				};
-			};
-		};
-
-		apbx@80040000 {
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
-			phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
-			status = "okay";
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-apf28dev.dts b/arch/arm/boot/dts/imx28-apf28dev.dts
deleted file mode 100644
index 1b253b47006c..000000000000
--- a/arch/arm/boot/dts/imx28-apf28dev.dts
+++ /dev/null
@@ -1,225 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2012 Armadeus Systems - <support@armadeus.com>
- */
-
-/* APF28Dev is a docking board for the APF28 SOM */
-#include "imx28-apf28.dts"
-
-/ {
-	model = "Armadeus Systems APF28Dev docking/development board";
-	compatible = "armadeus,imx28-apf28dev", "armadeus,imx28-apf28", "fsl,imx28";
-
-	apb@80000000 {
-		apbh@80000000 {
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_4bit_pins_a
-					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				bus-width = <4>;
-				status = "okay";
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-spi";
-				pinctrl-names = "default";
-				pinctrl-0 = <&spi2_pins_a>;
-				status = "okay";
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_apf28dev>;
-
-				hog_pins_apf28dev: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D16__GPIO_1_16
-						MX28_PAD_LCD_D17__GPIO_1_17
-						MX28_PAD_LCD_D18__GPIO_1_18
-						MX28_PAD_LCD_D19__GPIO_1_19
-						MX28_PAD_LCD_D20__GPIO_1_20
-						MX28_PAD_LCD_D21__GPIO_1_21
-						MX28_PAD_LCD_D22__GPIO_1_22
-						MX28_PAD_GPMI_CE1N__GPIO_0_17
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_apf28dev: lcdif-apf28dev@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RD_E__LCD_VSYNC
-						MX28_PAD_LCD_WR_RWN__LCD_HSYNC
-						MX28_PAD_LCD_RS__LCD_DOTCLK
-						MX28_PAD_LCD_CS__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				usb0_otg_apf28dev: otg-apf28dev@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D23__GPIO_1_23
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_16bit_pins_a
-						&lcdif_pins_apf28dev>;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <16>;
-					bus-width = <16>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <33000033>;
-							hactive = <800>;
-							vactive = <480>;
-							hback-porch = <96>;
-							hfront-porch = <96>;
-							vback-porch = <20>;
-							vfront-porch = <21>;
-							hsync-len = <64>;
-							vsync-len = <4>;
-							hsync-active = <1>;
-							vsync-active = <1>;
-							de-active = <1>;
-							pixelclk-active = <0>;
-						};
-					};
-				};
-			};
-
-			can0: can@80032000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&can0_pins_a>;
-				xceiver-supply = <&reg_can0_vcc>;
-				status = "okay";
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				fsl,lradc-touchscreen-wires = <4>;
-				status = "okay";
-			};
-
-			i2c0: i2c@80058000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c0_pins_a>;
-				status = "okay";
-			};
-
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm3_pins_a &pwm4_pins_a>;
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_pins_a>;
-				uart-has-rtscts;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-
-			usbphy1: usbphy@8007e000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb0_otg_apf28dev
-					&usb0_id_pins_b>;
-			vbus-supply = <&reg_usb0_vbus>;
-			status = "okay";
-		};
-
-		usb1: usb@80090000 {
-			status = "okay";
-		};
-
-		mac1: ethernet@800f4000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac1_pins_a>;
-			phy-reset-gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
-			status = "okay";
-		};
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_usb0_vbus: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "usb0_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio1 23 1>;
-			enable-active-high;
-		};
-
-		reg_can0_vcc: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "can0_vcc";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		user {
-			label = "Heartbeat";
-			gpios = <&gpio0 21 0>;
-			linux,default-trigger = "heartbeat";
-		};
-	};
-
-	backlight {
-		compatible = "pwm-backlight";
-
-		pwms = <&pwm 3 191000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <6>;
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		user-button {
-			label = "User button";
-			gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
-			linux,code = <0x100>;
-			wakeup-source;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-apx4devkit.dts b/arch/arm/boot/dts/imx28-apx4devkit.dts
deleted file mode 100644
index b86be320496b..000000000000
--- a/arch/arm/boot/dts/imx28-apx4devkit.dts
+++ /dev/null
@@ -1,240 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/dts-v1/;
-#include "imx28.dtsi"
-
-/ {
-	model = "Bluegiga APX4 Development Kit";
-	compatible = "bluegiga,apx4devkit", "fsl,imx28";
-
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x04000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			nand-controller@8000c000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
-				status = "okay";
-			};
-
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_sck_cfg>;
-				bus-width = <4>;
-				status = "okay";
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc2_4bit_pins_apx4 &mmc2_sck_cfg_apx4>;
-				bus-width = <4>;
-				status = "okay";
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_CE1N__GPIO_0_17
-						MX28_PAD_GPMI_RDY1__GPIO_0_21
-						MX28_PAD_SSP2_MISO__GPIO_2_18
-						MX28_PAD_SSP2_SS0__AUART3_TX /* was: 0x2131 - MX28_PAD_SSP2_SS0__GPIO_2_19 */
-						MX28_PAD_PWM3__GPIO_3_28
-						MX28_PAD_LCD_RESET__GPIO_3_30
-						MX28_PAD_JTAG_RTCK__GPIO_4_20
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_apx4: lcdif-apx4@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RD_E__LCD_VSYNC
-						MX28_PAD_LCD_WR_RWN__LCD_HSYNC
-						MX28_PAD_LCD_RS__LCD_DOTCLK
-						MX28_PAD_LCD_CS__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mmc2_4bit_pins_apx4: mmc2-4bit-apx4@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP0_DATA4__SSP2_D0
-						MX28_PAD_SSP0_DATA5__SSP2_D3
-						MX28_PAD_SSP0_DATA6__SSP2_CMD
-						MX28_PAD_SSP0_DATA7__SSP2_SCK
-						MX28_PAD_SSP2_SS1__SSP2_D1
-						MX28_PAD_SSP2_SS2__SSP2_D2
-					>;
-					fsl,drive-strength = <MXS_DRIVE_8mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				mmc2_sck_cfg_apx4: mmc2-sck-cfg-apx4@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP0_DATA7__SSP2_SCK
-					>;
-					fsl,drive-strength = <MXS_DRIVE_12mA>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_24bit_pins_a
-					     &lcdif_pins_apx4>;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <32>;
-					bus-width = <24>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <30000000>;
-							hactive = <800>;
-							vactive = <480>;
-							hback-porch = <88>;
-							hfront-porch = <40>;
-							vback-porch = <32>;
-							vfront-porch = <13>;
-							hsync-len = <48>;
-							vsync-len = <3>;
-							hsync-active = <1>;
-							vsync-active = <1>;
-							de-active = <1>;
-							pixelclk-active = <0>;
-						};
-					};
-				};
-			};
-		};
-
-		apbx@80040000 {
-			saif0: saif@80042000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&saif0_pins_a>;
-				status = "okay";
-			};
-
-			saif1: saif@80046000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&saif1_pins_a>;
-				fsl,saif-master = <&saif0>;
-				status = "okay";
-			};
-
-			i2c0: i2c@80058000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c0_pins_a>;
-				status = "okay";
-
-				sgtl5000: codec@a {
-					compatible = "fsl,sgtl5000";
-					reg = <0x0a>;
-					#sound-dai-cells = <0>;
-					VDDA-supply = <&reg_3p3v>;
-					VDDIO-supply = <&reg_3p3v>;
-					clocks = <&saif0>;
-				};
-
-				pcf8563: rtc@51 {
-					compatible = "phg,pcf8563";
-					reg = <0x51>;
-				};
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_pins_a>;
-				status = "okay";
-			};
-
-			auart1: serial@8006c000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart1_2pins_a>;
-				status = "okay";
-			};
-
-			auart2: serial@8006e000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart2_2pins_a>;
-				status = "okay";
-			};
-
-			usbphy1: usbphy@8007e000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&usb1_pins_a>;
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb1: usb@80090000 {
-		      status = "okay";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
-			status = "okay";
-		};
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-	};
-
-	sound {
-		compatible = "bluegiga,apx4devkit-sgtl5000",
-			     "fsl,mxs-audio-sgtl5000";
-		model = "apx4devkit-sgtl5000";
-		saif-controllers = <&saif0 &saif1>;
-		audio-codec = <&sgtl5000>;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		user {
-			label = "Heartbeat";
-			gpios = <&gpio3 28 0>;
-			linux,default-trigger = "heartbeat";
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-cfa10036.dts b/arch/arm/boot/dts/imx28-cfa10036.dts
deleted file mode 100644
index 85aa1cc3ff66..000000000000
--- a/arch/arm/boot/dts/imx28-cfa10036.dts
+++ /dev/null
@@ -1,140 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2012 Free Electrons
- */
-
-/dts-v1/;
-#include "imx28.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
-	model = "Crystalfontz CFA-10036 Board";
-	compatible = "crystalfontz,cfa10036", "fsl,imx28";
-
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			pinctrl@80018000 {
-				ssd1306_cfa10036: ssd1306-10036@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP0_DATA7__GPIO_2_7
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				led_pins_cfa10036: leds-10036@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_AUART1_RX__GPIO_3_4
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				usb0_otg_cfa10036: otg-10036@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_RDY0__USB0_ID
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mmc_pwr_cfa10036: mmc_pwr_cfa10036@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						0x31c3 /*
-						MX28_PAD_PWM3__GPIO_3_28 */
-					>;
-					fsl,drive-strength = <0>;
-					fsl,voltage = <1>;
-					fsl,pull-up = <0>;
-				};
-
-			};
-
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_4bit_pins_a
-					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				vmmc-supply = <&reg_vddio_sd0>;
-				bus-width = <4>;
-				status = "okay";
-			};
-		};
-
-		apbx@80040000 {
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_b>;
-				status = "okay";
-			};
-
-			i2c0: i2c@80058000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c0_pins_b>;
-				clock-frequency = <400000>;
-				status = "okay";
-
-				ssd1306: oled@3c {
-					compatible = "solomon,ssd1306fb-i2c";
-					pinctrl-names = "default";
-					pinctrl-0 = <&ssd1306_cfa10036>;
-					reg = <0x3c>;
-					reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
-					solomon,height = <32>;
-					solomon,width = <128>;
-					solomon,page-offset = <0>;
-					solomon,com-lrremap;
-					solomon,com-invdir;
-					solomon,com-offset = <32>;
-				};
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb0_otg_cfa10036>;
-			dr_mode = "peripheral";
-			phy_type = "utmi";
-			status = "okay";
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins_cfa10036>;
-
-		power {
-			gpios = <&gpio3 4 1>;
-			default-state = "on";
-		};
-	};
-
-	reg_vddio_sd0: vddio-sd0 {
-		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&mmc_pwr_cfa10036>;
-		regulator-name = "vddio-sd0";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		gpio = <&gpio3 28 0>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-cfa10049.dts b/arch/arm/boot/dts/imx28-cfa10049.dts
deleted file mode 100644
index a92b05ef390f..000000000000
--- a/arch/arm/boot/dts/imx28-cfa10049.dts
+++ /dev/null
@@ -1,428 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2012 Free Electrons
- */
-
-/*
- * The CFA-10049 is an expansion board for the CFA-10036 module, thus we
- * need to include the CFA-10036 DTS.
- */
-#include "imx28-cfa10036.dts"
-
-/ {
-	model = "Crystalfontz CFA-10049 Board";
-	compatible = "crystalfontz,cfa10049", "crystalfontz,cfa10036", "fsl,imx28";
-
-	i2cmux {
-		compatible = "i2c-mux-gpio";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2cmux_pins_cfa10049>;
-		mux-gpios = <&gpio1 22 0 &gpio1 23 0>;
-		i2c-parent = <&i2c1>;
-
-		i2c@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-
-			adc0: nau7802@2a {
-				compatible = "nuvoton,nau7802";
-				reg = <0x2a>;
-				nuvoton,vldo = <3000>;
-			};
-		};
-
-		i2c@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <1>;
-
-			adc1: nau7802@2a {
-				compatible = "nuvoton,nau7802";
-				reg = <0x2a>;
-				nuvoton,vldo = <3000>;
-			};
-		};
-
-		i2c@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <2>;
-
-				adc2: nau7802@2a {
-				compatible = "nuvoton,nau7802";
-				reg = <0x2a>;
-				nuvoton,vldo = <3000>;
-			};
-		};
-
-		i2c@3 {
-			reg = <3>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			pca9555: pca9555@20 {
-				compatible = "nxp,pca9555";
-				pinctrl-names = "default";
-				pinctrl-0 = <&pca_pins_cfa10049>;
-				interrupt-parent = <&gpio2>;
-				interrupts = <19 0x2>;
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				reg = <0x20>;
-			};
-		};
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			pinctrl@80018000 {
-				usb_pins_cfa10049: usb-10049@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_D07__GPIO_0_7
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				i2cmux_pins_cfa10049: i2cmux-10049@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D22__GPIO_1_22
-						MX28_PAD_LCD_D23__GPIO_1_23
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_pins_cfa10049: mac0-10049@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP2_SS2__GPIO_2_21
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				pca_pins_cfa10049: pca-10049@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP2_SS0__GPIO_2_19
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				rotary_pins_cfa10049: rotary-10049@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_I2C0_SCL__GPIO_3_24
-						MX28_PAD_I2C0_SDA__GPIO_3_25
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				rotary_btn_pins_cfa10049: rotary-btn-10049@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SAIF1_SDATA0__GPIO_3_26
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				spi2_pins_cfa10049: spi2-cfa10049@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP2_SCK__GPIO_2_16
-						MX28_PAD_SSP2_MOSI__GPIO_2_17
-						MX28_PAD_SSP2_MISO__GPIO_2_18
-						MX28_PAD_AUART1_TX__GPIO_3_5
-					>;
-					fsl,drive-strength = <MXS_DRIVE_8mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				spi3_pins_cfa10049: spi3-cfa10049@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_RDN__GPIO_0_24
-						MX28_PAD_GPMI_RESETN__GPIO_0_28
-						MX28_PAD_GPMI_CE1N__GPIO_0_17
-						MX28_PAD_GPMI_ALE__GPIO_0_26
-						MX28_PAD_GPMI_CLE__GPIO_0_27
-					>;
-					fsl,drive-strength = <MXS_DRIVE_8mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				lcdif_18bit_pins_cfa10049: lcdif-18bit@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D00__LCD_D0
-						MX28_PAD_LCD_D01__LCD_D1
-						MX28_PAD_LCD_D02__LCD_D2
-						MX28_PAD_LCD_D03__LCD_D3
-						MX28_PAD_LCD_D04__LCD_D4
-						MX28_PAD_LCD_D05__LCD_D5
-						MX28_PAD_LCD_D06__LCD_D6
-						MX28_PAD_LCD_D07__LCD_D7
-						MX28_PAD_LCD_D08__LCD_D8
-						MX28_PAD_LCD_D09__LCD_D9
-						MX28_PAD_LCD_D10__LCD_D10
-						MX28_PAD_LCD_D11__LCD_D11
-						MX28_PAD_LCD_D12__LCD_D12
-						MX28_PAD_LCD_D13__LCD_D13
-						MX28_PAD_LCD_D14__LCD_D14
-						MX28_PAD_LCD_D15__LCD_D15
-						MX28_PAD_LCD_D16__LCD_D16
-						MX28_PAD_LCD_D17__LCD_D17
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_cfa10049: lcdif-evk@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RD_E__LCD_VSYNC
-						MX28_PAD_LCD_WR_RWN__LCD_HSYNC
-						MX28_PAD_LCD_RS__LCD_DOTCLK
-						MX28_PAD_LCD_CS__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_cfa10049_pullup: lcdif-10049-pullup@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RESET__GPIO_3_30
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				w1_gpio_pins: w1-gpio@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D21__GPIO_1_21
-					>;
-					fsl,drive-strength = <MXS_DRIVE_8mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>; /* 0 will enable the keeper */
-				};
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_18bit_pins_cfa10049
-					     &lcdif_pins_cfa10049
-					     &lcdif_pins_cfa10049_pullup>;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <32>;
-					bus-width = <18>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <9216000>;
-							hactive = <320>;
-							vactive = <480>;
-							hback-porch = <2>;
-							hfront-porch = <2>;
-							vback-porch = <2>;
-							vfront-porch = <2>;
-							hsync-len = <15>;
-							vsync-len = <15>;
-							hsync-active = <0>;
-							vsync-active = <0>;
-							de-active = <1>;
-							pixelclk-active = <1>;
-						};
-					};
-				};
-			};
-		};
-
-		apbx@80040000 {
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm3_pins_b>;
-				status = "okay";
-			};
-
-			i2c1: i2c@8005a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c1_pins_a>;
-				status = "okay";
-			};
-
-			usbphy1: usbphy@8007e000 {
-				status = "okay";
-			};
-
-			lradc@80050000 {
-				status = "okay";
-				fsl,lradc-touchscreen-wires = <4>;
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb1: usb@80090000 {
-			vbus-supply = <&reg_usb1_vbus>;
-			pinctrl-0 = <&usb1_pins_a>;
-			pinctrl-names = "default";
-			status = "okay";
-		};
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_usb1_vbus: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb_pins_cfa10049>;
-			regulator-name = "usb1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio0 7 1>;
-		};
-	};
-
-	ahb@80080000 {
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a
-				&mac0_pins_cfa10049>;
-			phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <100>;
-			status = "okay";
-		};
-	};
-
-	spi2 {
-		compatible = "spi-gpio";
-		pinctrl-names = "default";
-		pinctrl-0 = <&spi2_pins_cfa10049>;
-		status = "okay";
-		gpio-sck = <&gpio2 16 0>;
-		gpio-mosi = <&gpio2 17 0>;
-		gpio-miso = <&gpio2 18 0>;
-		cs-gpios = <&gpio3 5 0>;
-		num-chipselects = <1>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		hx8357: hx8357@0 {
-			compatible = "himax,hx8357b", "himax,hx8357";
-			reg = <0>;
-			spi-max-frequency = <100000>;
-			spi-cpol;
-			spi-cpha;
-			gpios-reset = <&gpio3 30 0>;
-			im-gpios = <&gpio5 4 0 &gpio5 5 0 &gpio5 6 0>;
-		};
-	};
-
-	spi3 {
-		compatible = "spi-gpio";
-		pinctrl-names = "default";
-		pinctrl-0 = <&spi3_pins_cfa10049>;
-		status = "okay";
-		gpio-sck = <&gpio0 24 0>;
-		gpio-mosi = <&gpio0 28 0>;
-		cs-gpios = <&gpio0 17 0 &gpio0 26 0 &gpio0 27 0>;
-		num-chipselects = <3>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		gpio5: gpio5@0 {
-			compatible = "fairchild,74hc595";
-			gpio-controller;
-			#gpio-cells = <2>;
-			reg = <0>;
-			registers-number = <2>;
-			spi-max-frequency = <100000>;
-		};
-
-		gpio6: gpio6@1 {
-			compatible = "fairchild,74hc595";
-			gpio-controller;
-			#gpio-cells = <2>;
-			reg = <1>;
-			registers-number = <4>;
-			spi-max-frequency = <100000>;
-		};
-
-		dac0: dh2228@2 {
-			compatible = "rohm,dh2228fv";
-			reg = <2>;
-			spi-max-frequency = <100000>;
-		};
-	};
-
-	gpio_keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&rotary_btn_pins_cfa10049>;
-
-		rotary_button {
-			label = "rotary_button";
-			gpios = <&gpio3 26 1>;
-			debounce-interval = <10>;
-			linux,code = <28>;
-		};
-	};
-
-	rotary {
-		compatible = "rotary-encoder";
-		pinctrl-names = "default";
-		pinctrl-0 = <&rotary_pins_cfa10049>;
-		gpios = <&gpio3 24 1>, <&gpio3 25 1>;
-		linux,axis = <1>; /* REL_Y */
-		rotary-encoder,relative-axis;
-	};
-
-	backlight {
-		compatible = "pwm-backlight";
-		pwms = <&pwm 3 5000000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <6>;
-
-	};
-
-	onewire {
-		compatible = "w1-gpio";
-		pinctrl-names = "default";
-		pinctrl-0 = <&w1_gpio_pins>;
-		status = "okay";
-		gpios = <&gpio1 21 0>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-cfa10055.dts b/arch/arm/boot/dts/imx28-cfa10055.dts
deleted file mode 100644
index d05c370dfc17..000000000000
--- a/arch/arm/boot/dts/imx28-cfa10055.dts
+++ /dev/null
@@ -1,161 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2013 Crystalfontz America, Inc.
- * 				  Free Electrons
- */
-
-/*
- * The CFA-10055 is an expansion board for the CFA-10036 module and
- * CFA-10037, thus we need to include the CFA-10037 DTS.
- */
-#include "imx28-cfa10037.dts"
-
-/ {
-	model = "Crystalfontz CFA-10055 Board";
-	compatible = "crystalfontz,cfa10055", "crystalfontz,cfa10037", "crystalfontz,cfa10036", "fsl,imx28";
-
-	apb@80000000 {
-		apbh@80000000 {
-			pinctrl@80018000 {
-				spi2_pins_cfa10055: spi2-cfa10055@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP2_SCK__GPIO_2_16
-						MX28_PAD_SSP2_MOSI__GPIO_2_17
-						MX28_PAD_SSP2_MISO__GPIO_2_18
-						MX28_PAD_AUART1_TX__GPIO_3_5
-					>;
-					fsl,drive-strength = <MXS_DRIVE_8mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				lcdif_18bit_pins_cfa10055: lcdif-18bit@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D00__LCD_D0
-						MX28_PAD_LCD_D01__LCD_D1
-						MX28_PAD_LCD_D02__LCD_D2
-						MX28_PAD_LCD_D03__LCD_D3
-						MX28_PAD_LCD_D04__LCD_D4
-						MX28_PAD_LCD_D05__LCD_D5
-						MX28_PAD_LCD_D06__LCD_D6
-						MX28_PAD_LCD_D07__LCD_D7
-						MX28_PAD_LCD_D08__LCD_D8
-						MX28_PAD_LCD_D09__LCD_D9
-						MX28_PAD_LCD_D10__LCD_D10
-						MX28_PAD_LCD_D11__LCD_D11
-						MX28_PAD_LCD_D12__LCD_D12
-						MX28_PAD_LCD_D13__LCD_D13
-						MX28_PAD_LCD_D14__LCD_D14
-						MX28_PAD_LCD_D15__LCD_D15
-						MX28_PAD_LCD_D16__LCD_D16
-						MX28_PAD_LCD_D17__LCD_D17
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_cfa10055: lcdif-evk@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RD_E__LCD_VSYNC
-						MX28_PAD_LCD_WR_RWN__LCD_HSYNC
-						MX28_PAD_LCD_RS__LCD_DOTCLK
-						MX28_PAD_LCD_CS__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_cfa10055_pullup: lcdif-10055-pullup@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RESET__GPIO_3_30
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_18bit_pins_cfa10055
-					     &lcdif_pins_cfa10055
-					     &lcdif_pins_cfa10055_pullup>;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <32>;
-					bus-width = <18>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <9216000>;
-							hactive = <320>;
-							vactive = <480>;
-							hback-porch = <2>;
-							hfront-porch = <2>;
-							vback-porch = <2>;
-							vfront-porch = <2>;
-							hsync-len = <15>;
-							vsync-len = <15>;
-							hsync-active = <0>;
-							vsync-active = <0>;
-							de-active = <1>;
-							pixelclk-active = <1>;
-						};
-					};
-				};
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				fsl,lradc-touchscreen-wires = <4>;
-				status = "okay";
-			};
-
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm3_pins_b>;
-				status = "okay";
-			};
-		};
-	};
-
-	spi2 {
-		compatible = "spi-gpio";
-		pinctrl-names = "default";
-		pinctrl-0 = <&spi2_pins_cfa10055>;
-		status = "okay";
-		gpio-sck = <&gpio2 16 0>;
-		gpio-mosi = <&gpio2 17 0>;
-		gpio-miso = <&gpio2 18 0>;
-		cs-gpios = <&gpio3 5 0>;
-		num-chipselects = <1>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		hx8357: hx8357@0 {
-			compatible = "himax,hx8357b", "himax,hx8357";
-			reg = <0>;
-			spi-max-frequency = <100000>;
-			spi-cpol;
-			spi-cpha;
-			gpios-reset = <&gpio3 30 0>;
-		};
-	};
-
-	backlight {
-		compatible = "pwm-backlight";
-		pwms = <&pwm 3 5000000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <6>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-cfa10056.dts b/arch/arm/boot/dts/imx28-cfa10056.dts
deleted file mode 100644
index c1060bd5f17f..000000000000
--- a/arch/arm/boot/dts/imx28-cfa10056.dts
+++ /dev/null
@@ -1,113 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2013 Free Electrons
- */
-
-/*
- * The CFA-10055 is an expansion board for the CFA-10036 module and
- * CFA-10037, thus we need to include the CFA-10037 DTS.
- */
-#include "imx28-cfa10037.dts"
-
-/ {
-	model = "Crystalfontz CFA-10056 Board";
-	compatible = "crystalfontz,cfa10056", "crystalfontz,cfa10037", "crystalfontz,cfa10036", "fsl,imx28";
-
-	apb@80000000 {
-		apbh@80000000 {
-			pinctrl@80018000 {
-				spi2_pins_cfa10056: spi2-cfa10056@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP2_SCK__GPIO_2_16
-						MX28_PAD_SSP2_MOSI__GPIO_2_17
-						MX28_PAD_SSP2_MISO__GPIO_2_18
-						MX28_PAD_AUART1_TX__GPIO_3_5
-					>;
-					fsl,drive-strength = <MXS_DRIVE_8mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				lcdif_pins_cfa10056: lcdif-10056@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RD_E__LCD_VSYNC
-						MX28_PAD_LCD_WR_RWN__LCD_HSYNC
-						MX28_PAD_LCD_RS__LCD_DOTCLK
-						MX28_PAD_LCD_CS__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_cfa10056_pullup: lcdif-10056-pullup@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RESET__GPIO_3_30
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_24bit_pins_a
-						&lcdif_pins_cfa10056
-						&lcdif_pins_cfa10056_pullup >;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <32>;
-					bus-width = <24>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <32000000>;
-							hactive = <480>;
-							vactive = <800>;
-							hback-porch = <2>;
-							hfront-porch = <2>;
-							vback-porch = <2>;
-							vfront-porch = <2>;
-							hsync-len = <5>;
-							vsync-len = <5>;
-							hsync-active = <0>;
-							vsync-active = <0>;
-							de-active = <1>;
-							pixelclk-active = <1>;
-						};
-					};
-				};
-			};
-		};
-	};
-
-	spi2 {
-		compatible = "spi-gpio";
-		pinctrl-names = "default";
-		pinctrl-0 = <&spi2_pins_cfa10056>;
-		status = "okay";
-		gpio-sck = <&gpio2 16 0>;
-		gpio-mosi = <&gpio2 17 0>;
-		gpio-miso = <&gpio2 18 0>;
-		cs-gpios = <&gpio3 5 0>;
-		num-chipselects = <1>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		hx8369: hx8369@0 {
-			compatible = "himax,hx8369a", "himax,hx8369";
-			reg = <0>;
-			spi-max-frequency = <100000>;
-			spi-cpol;
-			spi-cpha;
-			gpios-reset = <&gpio3 30 0>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-cfa10057.dts b/arch/arm/boot/dts/imx28-cfa10057.dts
deleted file mode 100644
index 2f7e479dbc74..000000000000
--- a/arch/arm/boot/dts/imx28-cfa10057.dts
+++ /dev/null
@@ -1,171 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2013 Crystalfontz America, Inc.
- * Copyright 2012 Free Electrons
- */
-
-/*
- * The CFA-10057 is an expansion board for the CFA-10036 module, thus we
- * need to include the CFA-10036 DTS.
- */
-#include "imx28-cfa10036.dts"
-
-/ {
-	model = "Crystalfontz CFA-10057 Board";
-	compatible = "crystalfontz,cfa10057", "crystalfontz,cfa10036", "fsl,imx28";
-
-	apb@80000000 {
-		apbh@80000000 {
-			pinctrl@80018000 {
-				usb_pins_cfa10057: usb-10057@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_D07__GPIO_0_7
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_18bit_pins_cfa10057: lcdif-18bit@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D00__LCD_D0
-						MX28_PAD_LCD_D01__LCD_D1
-						MX28_PAD_LCD_D02__LCD_D2
-						MX28_PAD_LCD_D03__LCD_D3
-						MX28_PAD_LCD_D04__LCD_D4
-						MX28_PAD_LCD_D05__LCD_D5
-						MX28_PAD_LCD_D06__LCD_D6
-						MX28_PAD_LCD_D07__LCD_D7
-						MX28_PAD_LCD_D08__LCD_D8
-						MX28_PAD_LCD_D09__LCD_D9
-						MX28_PAD_LCD_D10__LCD_D10
-						MX28_PAD_LCD_D11__LCD_D11
-						MX28_PAD_LCD_D12__LCD_D12
-						MX28_PAD_LCD_D13__LCD_D13
-						MX28_PAD_LCD_D14__LCD_D14
-						MX28_PAD_LCD_D15__LCD_D15
-						MX28_PAD_LCD_D16__LCD_D16
-						MX28_PAD_LCD_D17__LCD_D17
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_cfa10057: lcdif-evk@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RD_E__LCD_VSYNC
-						MX28_PAD_LCD_WR_RWN__LCD_HSYNC
-						MX28_PAD_LCD_RS__LCD_DOTCLK
-						MX28_PAD_LCD_CS__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_18bit_pins_cfa10057
-					     &lcdif_pins_cfa10057>;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <32>;
-					bus-width = <18>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <30000000>;
-							hactive = <480>;
-							vactive = <800>;
-							hfront-porch = <12>;
-							hback-porch = <2>;
-							vfront-porch = <5>;
-							vback-porch = <3>;
-							hsync-len = <2>;
-							vsync-len = <2>;
-							hsync-active = <0>;
-							vsync-active = <0>;
-							de-active = <1>;
-							pixelclk-active = <1>;
-						};
-					};
-				};
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				fsl,lradc-touchscreen-wires = <4>;
-				status = "okay";
-			};
-
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm4_pins_a>;
-				status = "okay";
-			};
-
-			i2c1: i2c@8005a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c1_pins_a>;
-				status = "okay";
-			};
-
-			usbphy1: usbphy@8007e000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb1: usb@80090000 {
-			vbus-supply = <&reg_usb1_vbus>;
-			pinctrl-0 = <&usb1_pins_a>;
-			pinctrl-names = "default";
-			status = "okay";
-		};
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_usb1_vbus: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb_pins_cfa10057>;
-			regulator-name = "usb1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio0 7 1>;
-		};
-	};
-
-	ahb@80080000 {
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
-			phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <100>;
-			status = "okay";
-		};
-	};
-
-	backlight {
-		compatible = "pwm-backlight";
-		pwms = <&pwm 4 5000000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <7>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-cfa10058.dts b/arch/arm/boot/dts/imx28-cfa10058.dts
deleted file mode 100644
index 4465fd86785a..000000000000
--- a/arch/arm/boot/dts/imx28-cfa10058.dts
+++ /dev/null
@@ -1,138 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2013 Crystalfontz America, Inc.
- * Copyright 2013 Free Electrons
- */
-
-/*
- * The CFA-10058 is an expansion board for the CFA-10036 module, thus we
- * need to include the CFA-10036 DTS.
- */
-#include "imx28-cfa10036.dts"
-
-/ {
-	model = "Crystalfontz CFA-10058 Board";
-	compatible = "crystalfontz,cfa10058", "crystalfontz,cfa10036", "fsl,imx28";
-
-	apb@80000000 {
-		apbh@80000000 {
-			pinctrl@80018000 {
-				usb_pins_cfa10058: usb-10058@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_D07__GPIO_0_7
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_cfa10058: lcdif-10058@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RD_E__LCD_VSYNC
-						MX28_PAD_LCD_WR_RWN__LCD_HSYNC
-						MX28_PAD_LCD_RS__LCD_DOTCLK
-						MX28_PAD_LCD_CS__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_24bit_pins_a
-						 &lcdif_pins_cfa10058>;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <32>;
-					bus-width = <24>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <30000000>;
-							hactive = <800>;
-							vactive = <480>;
-							hback-porch = <40>;
-							hfront-porch = <40>;
-							vback-porch = <13>;
-							vfront-porch = <29>;
-							hsync-len = <8>;
-							vsync-len = <8>;
-							hsync-active = <0>;
-							vsync-active = <0>;
-							de-active = <1>;
-							pixelclk-active = <1>;
-						};
-					};
-				};
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				fsl,lradc-touchscreen-wires = <4>;
-				status = "okay";
-			};
-
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm3_pins_b>;
-				status = "okay";
-			};
-
-			usbphy1: usbphy@8007e000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb1: usb@80090000 {
-			vbus-supply = <&reg_usb1_vbus>;
-			pinctrl-0 = <&usb1_pins_a>;
-			pinctrl-names = "default";
-			status = "okay";
-		};
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_usb1_vbus: regulator@0 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb_pins_cfa10058>;
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "usb1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio0 7 1>;
-		};
-	};
-
-	ahb@80080000 {
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
-			phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <100>;
-			status = "okay";
-		};
-	};
-
-	backlight {
-		compatible = "pwm-backlight";
-		pwms = <&pwm 3 5000000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <6>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-duckbill-2-485.dts b/arch/arm/boot/dts/imx28-duckbill-2-485.dts
deleted file mode 100644
index d451fa018d83..000000000000
--- a/arch/arm/boot/dts/imx28-duckbill-2-485.dts
+++ /dev/null
@@ -1,184 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
- * Copyright (C) 2016 Michael Heimpold <mhei@heimpold.de>
- */
-
-/dts-v1/;
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/gpio/gpio.h>
-#include "imx28.dtsi"
-
-/ {
-	model = "I2SE Duckbill 2 485";
-	compatible = "i2se,duckbill-2-485", "i2se,duckbill-2", "fsl,imx28";
-
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_8bit_pins_a
-					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				bus-width = <8>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-				non-removable;
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc2_4bit_pins_b
-					&mmc2_cd_cfg &mmc2_sck_cfg_b>;
-				bus-width = <4>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D17__GPIO_1_17    /* Revision detection */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_reset_pin: mac0-phy-reset@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_ALE__GPIO_0_26    /* PHY Reset */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_int_pin: mac0-phy-int@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_D07__GPIO_0_7    /* PHY Interrupt */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				led_pins: leds@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SAIF0_MCLK__GPIO_3_20
-						MX28_PAD_SAIF0_LRCLK__GPIO_3_21
-						MX28_PAD_I2C0_SCL__GPIO_3_24
-						MX28_PAD_I2C0_SDA__GPIO_3_25
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_2pins_a>;
-				status = "okay";
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			status = "okay";
-			dr_mode = "peripheral";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
-			phy-supply = <&reg_3p3v>;
-			phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <25>;
-			phy-handle = <&ethphy>;
-			status = "okay";
-
-			mdio {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				ethphy: ethernet-phy@0 {
-					compatible = "ethernet-phy-ieee802.3-c22";
-					reg = <0>;
-					pinctrl-names = "default";
-					pinctrl-0 = <&mac0_phy_int_pin>;
-					interrupt-parent = <&gpio0>;
-					interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
-					max-speed = <100>;
-				};
-			};
-		};
-	};
-
-	reg_3p3v: regulator-3p3v {
-		compatible = "regulator-fixed";
-		regulator-name = "3P3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins>;
-
-		status-red {
-			label = "duckbill:red:status";
-			gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "default-on";
-		};
-
-		status-green {
-			label = "duckbill:green:status";
-			gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-		};
-
-		rs485-red {
-			label = "duckbill:red:rs485";
-			gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
-		};
-
-		rs485-green {
-			label = "duckbill:green:rs485";
-			gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts b/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts
deleted file mode 100644
index bacb846f99e3..000000000000
--- a/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts
+++ /dev/null
@@ -1,213 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
- * Copyright (C) 2016 Michael Heimpold <mhei@heimpold.de>
- */
-
-/dts-v1/;
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/gpio/gpio.h>
-#include "imx28.dtsi"
-
-/ {
-	model = "I2SE Duckbill 2 EnOcean";
-	compatible = "i2se,duckbill-2-enocean", "i2se,duckbill-2", "fsl,imx28";
-
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_8bit_pins_a
-					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				bus-width = <8>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-				non-removable;
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc2_4bit_pins_b
-					&mmc2_cd_cfg &mmc2_sck_cfg_b>;
-				bus-width = <4>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D17__GPIO_1_17    /* Revision detection */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_reset_pin: mac0-phy-reset@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_ALE__GPIO_0_26    /* PHY Reset */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_int_pin: mac0-phy-int@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_D07__GPIO_0_7    /* PHY Interrupt */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				led_pins: leds@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SAIF0_MCLK__GPIO_3_20
-						MX28_PAD_SAIF0_LRCLK__GPIO_3_21
-						MX28_PAD_AUART0_CTS__GPIO_3_2
-						MX28_PAD_I2C0_SCL__GPIO_3_24
-						MX28_PAD_I2C0_SDA__GPIO_3_25
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				enocean_button: enocean-button@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_AUART0_RTS__GPIO_3_3
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_2pins_a>;
-				status = "okay";
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			status = "okay";
-			dr_mode = "peripheral";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
-			phy-supply = <&reg_3p3v>;
-			phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <25>;
-			phy-handle = <&ethphy>;
-			status = "okay";
-
-			mdio {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				ethphy: ethernet-phy@0 {
-					compatible = "ethernet-phy-ieee802.3-c22";
-					reg = <0>;
-					pinctrl-names = "default";
-					pinctrl-0 = <&mac0_phy_int_pin>;
-					interrupt-parent = <&gpio0>;
-					interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
-					max-speed = <100>;
-				};
-			};
-		};
-	};
-
-	reg_3p3v: regulator-3p3v {
-		compatible = "regulator-fixed";
-		regulator-name = "3P3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins>;
-
-		status-red {
-			label = "duckbill:red:status";
-			gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "default-on";
-		};
-
-		status-green {
-			label = "duckbill:green:status";
-			gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-		};
-
-		enocean-blue {
-			label = "duckbill:blue:enocean";
-			gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
-		};
-
-		enocean-red {
-			label = "duckbill:red:enocean";
-			gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
-		};
-
-		enocean-green {
-			label = "duckbill:green:enocean";
-			gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&enocean_button>;
-
-		enocean {
-			label = "EnOcean";
-			linux,code = <KEY_NEW>;
-			gpios = <&gpio3 3 GPIO_ACTIVE_HIGH>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-duckbill-2-spi.dts b/arch/arm/boot/dts/imx28-duckbill-2-spi.dts
deleted file mode 100644
index 0e8be5975709..000000000000
--- a/arch/arm/boot/dts/imx28-duckbill-2-spi.dts
+++ /dev/null
@@ -1,194 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
- * Copyright (C) 2016 Michael Heimpold <mhei@heimpold.de>
- */
-
-/dts-v1/;
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/gpio/gpio.h>
-#include "imx28.dtsi"
-
-/ {
-	model = "I2SE Duckbill 2 SPI";
-	compatible = "i2se,duckbill-2-spi", "i2se,duckbill-2", "fsl,imx28";
-
-	aliases {
-		ethernet1 = &qca7000;
-	};
-
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_8bit_pins_a
-					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				bus-width = <8>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-				non-removable;
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-spi";
-				pinctrl-names = "default";
-				pinctrl-0 = <&spi2_pins_a>;
-				status = "okay";
-
-				qca7000: ethernet@0 {
-					reg = <0>;
-					compatible = "qca,qca7000";
-					pinctrl-names = "default";
-					pinctrl-0 = <&qca7000_pins>;
-					interrupt-parent = <&gpio3>;
-					interrupts = <3 IRQ_TYPE_EDGE_RISING>;
-					spi-cpha;
-					spi-cpol;
-					spi-max-frequency = <8000000>;
-				};
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D17__GPIO_1_17    /* Revision detection */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_reset_pin: mac0-phy-reset@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_ALE__GPIO_0_26    /* PHY Reset */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_int_pin: mac0-phy-int@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_D07__GPIO_0_7    /* PHY Interrupt */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				led_pins: led@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SAIF0_MCLK__GPIO_3_20
-						MX28_PAD_SAIF0_LRCLK__GPIO_3_21
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				qca7000_pins: qca7000@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_AUART0_RTS__GPIO_3_3    /* Interrupt */
-						MX28_PAD_LCD_D13__GPIO_1_13      /* QCA7K reset */
-						MX28_PAD_LCD_D14__GPIO_1_14      /* GPIO 0 */
-						MX28_PAD_LCD_D15__GPIO_1_15      /* GPIO 1 */
-						MX28_PAD_LCD_D18__GPIO_1_18      /* GPIO 2 */
-						MX28_PAD_LCD_D21__GPIO_1_21      /* GPIO 3 */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				status = "okay";
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			status = "okay";
-			dr_mode = "peripheral";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
-			phy-supply = <&reg_3p3v>;
-			phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <25>;
-			phy-handle = <&ethphy>;
-			status = "okay";
-
-			mdio {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				ethphy: ethernet-phy@0 {
-					compatible = "ethernet-phy-ieee802.3-c22";
-					reg = <0>;
-					pinctrl-names = "default";
-					pinctrl-0 = <&mac0_phy_int_pin>;
-					interrupt-parent = <&gpio0>;
-					interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
-					max-speed = <100>;
-				};
-			};
-		};
-	};
-
-	reg_3p3v: regulator-3p3v {
-		compatible = "regulator-fixed";
-		regulator-name = "3P3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins>;
-
-		status-red {
-			label = "duckbill:red:status";
-			gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "default-on";
-		};
-
-		status-green {
-			label = "duckbill:green:status";
-			gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-duckbill-2.dts b/arch/arm/boot/dts/imx28-duckbill-2.dts
deleted file mode 100644
index 23fd3036404d..000000000000
--- a/arch/arm/boot/dts/imx28-duckbill-2.dts
+++ /dev/null
@@ -1,178 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
- * Copyright (C) 2016 Michael Heimpold <mhei@heimpold.de>
- */
-
-/dts-v1/;
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/gpio/gpio.h>
-#include "imx28.dtsi"
-
-/ {
-	model = "I2SE Duckbill 2";
-	compatible = "i2se,duckbill-2", "fsl,imx28";
-
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_8bit_pins_a
-					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				bus-width = <8>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-				non-removable;
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc2_4bit_pins_b
-					&mmc2_cd_cfg &mmc2_sck_cfg_b>;
-				bus-width = <4>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D17__GPIO_1_17    /* Revision detection */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_reset_pin: mac0-phy-reset@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_ALE__GPIO_0_26    /* PHY Reset */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_int_pin: mac0-phy-int@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_D07__GPIO_0_7    /* PHY Interrupt */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				led_pins: leds@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SAIF0_MCLK__GPIO_3_20
-						MX28_PAD_SAIF0_LRCLK__GPIO_3_21
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				status = "okay";
-			};
-
-			i2c0: i2c@80058000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c0_pins_a>;
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_2pins_a>;
-				status = "okay";
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			status = "okay";
-			dr_mode = "peripheral";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
-			phy-supply = <&reg_3p3v>;
-			phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <25>;
-			phy-handle = <&ethphy>;
-			status = "okay";
-
-			mdio {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				ethphy: ethernet-phy@0 {
-					compatible = "ethernet-phy-ieee802.3-c22";
-					reg = <0>;
-					pinctrl-names = "default";
-					pinctrl-0 = <&mac0_phy_int_pin>;
-					interrupt-parent = <&gpio0>;
-					interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
-					max-speed = <100>;
-				};
-			};
-		};
-	};
-
-	reg_3p3v: regulator-3p3v {
-		compatible = "regulator-fixed";
-		regulator-name = "3P3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins>;
-
-		status-red {
-			label = "duckbill:red:status";
-			gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "default-on";
-		};
-
-		status-green {
-			label = "duckbill:green:status";
-			gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-duckbill.dts b/arch/arm/boot/dts/imx28-duckbill.dts
deleted file mode 100644
index c666afb12445..000000000000
--- a/arch/arm/boot/dts/imx28-duckbill.dts
+++ /dev/null
@@ -1,147 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2013-2014,2016 Michael Heimpold <mhei@heimpold.de>
- * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
- */
-
-/dts-v1/;
-#include <dt-bindings/gpio/gpio.h>
-#include "imx28.dtsi"
-
-/ {
-	model = "I2SE Duckbill";
-	compatible = "i2se,duckbill", "fsl,imx28";
-
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_4bit_pins_a
-					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				bus-width = <4>;
-				vmmc-supply = <&reg_3p3v>;
-				status = "okay";
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-spi";
-				pinctrl-names = "default";
-				pinctrl-0 = <&spi2_pins_a>;
-				status = "okay";
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_D17__GPIO_1_17    /* Revision detection */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mac0_phy_reset_pin: mac0-phy-reset@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP0_DATA7__GPIO_2_7    /* PHY Reset */
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				led_pins: leds@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_AUART1_RX__GPIO_3_4
-						MX28_PAD_AUART1_TX__GPIO_3_5
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-		};
-
-		apbx@80040000 {
-			lradc@80050000 {
-				status = "okay";
-			};
-
-			i2c0: i2c@80058000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c0_pins_a>;
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_2pins_a>;
-				status = "okay";
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			status = "okay";
-			dr_mode = "peripheral";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
-			phy-supply = <&reg_3p3v>;
-			phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <25>;
-			status = "okay";
-		};
-	};
-
-	reg_3p3v: regulator-3p3v {
-		compatible = "regulator-fixed";
-		regulator-name = "3P3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins>;
-
-		status-red {
-			label = "duckbill:red:status";
-			gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "default-on";
-		};
-
-		status-green {
-			label = "duckbill:green:status";
-			gpios = <&gpio3 5 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts
deleted file mode 100644
index 7e2b0f198dfa..000000000000
--- a/arch/arm/boot/dts/imx28-evk.dts
+++ /dev/null
@@ -1,360 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-//
-// Copyright 2012 Freescale Semiconductor, Inc.
-
-/dts-v1/;
-#include "imx28.dtsi"
-
-/ {
-	model = "Freescale i.MX28 Evaluation Kit";
-	compatible = "fsl,imx28-evk", "fsl,imx28";
-
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-
-	reg_3p3v: regulator-3p3v {
-		compatible = "regulator-fixed";
-		regulator-name = "3P3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-
-	reg_vddio_sd0: regulator-vddio-sd0 {
-		compatible = "regulator-fixed";
-		regulator-name = "vddio-sd0";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		gpio = <&gpio3 28 0>;
-	};
-
-	reg_fec_3v3: regulator-fec-3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "fec-3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		gpio = <&gpio2 15 0>;
-	};
-
-	reg_usb0_vbus: regulator-usb0-vbus {
-		compatible = "regulator-fixed";
-		regulator-name = "usb0_vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio3 9 0>;
-		enable-active-high;
-	};
-
-	reg_usb1_vbus: regulator-usb1-vbus {
-		compatible = "regulator-fixed";
-		regulator-name = "usb1_vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio3 8 0>;
-		enable-active-high;
-	};
-
-	reg_lcd_3v3: regulator-lcd-3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "lcd-3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		gpio = <&gpio3 30 0>;
-		enable-active-high;
-	};
-
-	reg_can_3v3: regulator-can-3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "can-3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		gpio = <&gpio2 13 0>;
-		enable-active-high;
-	};
-
-	reg_lcd_5v: regulator-lcd-5v {
-		compatible = "regulator-fixed";
-		regulator-name = "lcd-5v";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-	};
-
-	panel {
-		compatible = "sii,43wvf1g";
-		backlight = <&backlight_display>;
-		dvdd-supply = <&reg_lcd_3v3>;
-		avdd-supply = <&reg_lcd_5v>;
-
-		port {
-			panel_in: endpoint {
-				remote-endpoint = <&display_out>;
-			};
-		};
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			nand-controller@8000c000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg
-					     &gpmi_pins_evk>;
-				status = "okay";
-			};
-
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_8bit_pins_a
-					&mmc0_cd_cfg &mmc0_sck_cfg>;
-				bus-width = <8>;
-				wp-gpios = <&gpio2 12 0>;
-				vmmc-supply = <&reg_vddio_sd0>;
-				status = "okay";
-			};
-
-			ssp1: spi@80012000 {
-				compatible = "fsl,imx28-mmc";
-				bus-width = <8>;
-				wp-gpios = <&gpio0 28 0>;
-			};
-
-			ssp2: spi@80014000 {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				compatible = "fsl,imx28-spi";
-				pinctrl-names = "default";
-				pinctrl-0 = <&spi2_pins_a>;
-				status = "okay";
-
-				flash: m25p80@0 {
-					#address-cells = <1>;
-					#size-cells = <1>;
-					compatible = "sst,sst25vf016b", "jedec,spi-nor";
-					spi-max-frequency = <40000000>;
-					reg = <0>;
-				};
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP1_CMD__GPIO_2_13
-						MX28_PAD_SSP1_DATA3__GPIO_2_15
-						MX28_PAD_ENET0_RX_CLK__GPIO_4_13
-						MX28_PAD_SSP1_SCK__GPIO_2_12
-						MX28_PAD_PWM3__GPIO_3_28
-						MX28_PAD_LCD_RESET__GPIO_3_30
-						MX28_PAD_AUART2_RX__GPIO_3_8
-						MX28_PAD_AUART2_TX__GPIO_3_9
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				led_pin_gpio3_5: led_gpio3_5@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_AUART1_TX__GPIO_3_5
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				gpmi_pins_evk: gpmi-nand-evk@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_CE1N__GPMI_CE1N
-						MX28_PAD_GPMI_RDY1__GPMI_READY1
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_evk: lcdif-evk@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RD_E__LCD_VSYNC
-						MX28_PAD_LCD_WR_RWN__LCD_HSYNC
-						MX28_PAD_LCD_RS__LCD_DOTCLK
-						MX28_PAD_LCD_CS__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_24bit_pins_a
-					     &lcdif_pins_evk>;
-				status = "okay";
-
-				port {
-					display_out: endpoint {
-						remote-endpoint = <&panel_in>;
-					};
-				};
-			};
-
-			can0: can@80032000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&can0_pins_a>;
-				xceiver-supply = <&reg_can_3v3>;
-				status = "okay";
-			};
-
-			can1: can@80034000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&can1_pins_a>;
-				xceiver-supply = <&reg_can_3v3>;
-				status = "okay";
-			};
-		};
-
-		apbx@80040000 {
-			saif0: saif@80042000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&saif0_pins_a>;
-				status = "okay";
-			};
-
-			saif1: saif@80046000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&saif1_pins_a>;
-				fsl,saif-master = <&saif0>;
-				status = "okay";
-			};
-
-			lradc@80050000 {
-				status = "okay";
-				fsl,lradc-touchscreen-wires = <4>;
-				fsl,ave-ctrl = <4>;
-				fsl,ave-delay = <2>;
-				fsl,settling = <10>;
-			};
-
-			i2c0: i2c@80058000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c0_pins_a>;
-				status = "okay";
-
-				sgtl5000: codec@a {
-					compatible = "fsl,sgtl5000";
-					reg = <0x0a>;
-					#sound-dai-cells = <0>;
-					VDDA-supply = <&reg_3p3v>;
-					VDDIO-supply = <&reg_3p3v>;
-					clocks = <&saif0>;
-				};
-
-				at24@51 {
-					compatible = "atmel,24c32";
-					pagesize = <32>;
-					reg = <0x51>;
-				};
-			};
-
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm2_pins_a>;
-				status = "okay";
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_pins_a>;
-				uart-has-rtscts;
-				status = "okay";
-			};
-
-			auart3: serial@80070000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart3_pins_a>;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-
-			usbphy1: usbphy@8007e000 {
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb0_id_pins_a>;
-			vbus-supply = <&reg_usb0_vbus>;
-			status = "okay";
-		};
-
-		usb1: usb@80090000 {
-			vbus-supply = <&reg_usb1_vbus>;
-			status = "okay";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
-			phy-supply = <&reg_fec_3v3>;
-			phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <100>;
-			status = "okay";
-		};
-
-		mac1: ethernet@800f4000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac1_pins_a>;
-			status = "okay";
-		};
-	};
-
-	sound {
-		compatible = "fsl,imx28-evk-sgtl5000",
-			     "fsl,mxs-audio-sgtl5000";
-		model = "imx28-evk-sgtl5000";
-		saif-controllers = <&saif0 &saif1>;
-		audio-codec = <&sgtl5000>;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pin_gpio3_5>;
-
-		user {
-			label = "Heartbeat";
-			gpios = <&gpio3 5 0>;
-			linux,default-trigger = "heartbeat";
-		};
-	};
-
-	backlight_display: backlight {
-		compatible = "pwm-backlight";
-		pwms = <&pwm 2 5000000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <6>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-m28.dtsi b/arch/arm/boot/dts/imx28-m28.dtsi
deleted file mode 100644
index 2bdb4c093545..000000000000
--- a/arch/arm/boot/dts/imx28-m28.dtsi
+++ /dev/null
@@ -1,56 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2014 Marek Vasut <marex@denx.de>
- */
-
-#include "imx28.dtsi"
-
-/ {
-	model = "Aries/DENX M28";
-	compatible = "aries,m28", "denx,m28", "fsl,imx28";
-
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			nand-controller@8000c000 {
-				#address-cells = <1>;
-				#size-cells = <1>;
-				pinctrl-names = "default";
-				pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
-				status = "okay";
-			};
-		};
-
-		apbx@80040000 {
-			i2c0: i2c@80058000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c0_pins_a>;
-				status = "okay";
-
-				rtc: rtc@68 {
-					compatible = "st,m41t62";
-					reg = <0x68>;
-				};
-			};
-		};
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-m28cu3.dts b/arch/arm/boot/dts/imx28-m28cu3.dts
deleted file mode 100644
index 865ac3d573c7..000000000000
--- a/arch/arm/boot/dts/imx28-m28cu3.dts
+++ /dev/null
@@ -1,266 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2013 Marek Vasut <marex@denx.de>
- */
-
-/dts-v1/;
-#include "imx28.dtsi"
-
-/ {
-	model = "MSR M28CU3";
-	compatible = "msr,m28cu3", "fsl,imx28";
-
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			nand-controller@8000c000 {
-				#address-cells = <1>;
-				#size-cells = <1>;
-				pinctrl-names = "default";
-				pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
-				status = "okay";
-
-				partition@0 {
-					label = "gpmi-nfc-0-boot";
-					reg = <0x00000000 0x01400000>;
-					read-only;
-				};
-
-				partition@1 {
-					label = "gpmi-nfc-general-use";
-					reg = <0x01400000 0x0ec00000>;
-				};
-			};
-
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_4bit_pins_a
-					     &mmc0_cd_cfg
-					     &mmc0_sck_cfg>;
-				bus-width = <4>;
-				vmmc-supply = <&reg_vddio_sd0>;
-				status = "okay";
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc2_4bit_pins_a
-					     &mmc2_cd_cfg
-					     &mmc2_sck_cfg_a>;
-				bus-width = <4>;
-				vmmc-supply = <&reg_vddio_sd1>;
-				status = "okay";
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP2_SS0__GPIO_2_19
-						MX28_PAD_PWM4__GPIO_3_29
-						MX28_PAD_AUART2_RX__GPIO_3_8
-						MX28_PAD_ENET0_RX_CLK__GPIO_4_13
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_m28: lcdif-m28@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_VSYNC__LCD_VSYNC
-						MX28_PAD_LCD_HSYNC__LCD_HSYNC
-						MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
-						MX28_PAD_LCD_RESET__LCD_RESET
-						MX28_PAD_LCD_CS__LCD_ENABLE
-						MX28_PAD_AUART1_TX__GPIO_3_5
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				led_pins_gpio: leds-m28@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP3_MISO__GPIO_2_26
-						MX28_PAD_SSP3_SCK__GPIO_2_24
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-
-			ocotp@8002c000 {
-				status = "okay";
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_24bit_pins_a
-					     &lcdif_pins_m28>;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <32>;
-					bus-width = <24>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <6410256>;
-							hactive = <320>;
-							vactive = <240>;
-							hback-porch = <38>;
-							hfront-porch = <20>;
-							vback-porch = <15>;
-							vfront-porch = <5>;
-							hsync-len = <30>;
-							vsync-len = <3>;
-							hsync-active = <0>;
-							vsync-active = <0>;
-							de-active = <1>;
-							pixelclk-active = <1>;
-						};
-					};
-				};
-			};
-		};
-
-		apbx@80040000 {
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_b>;
-				status = "okay";
-			};
-
-			usbphy1: usbphy@8007e000 {
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_2pins_a>;
-				status = "okay";
-			};
-
-			auart3: serial@80070000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart3_2pins_b>;
-				status = "okay";
-			};
-
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm3_pins_a>;
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb1: usb@80090000 {
-			vbus-supply = <&reg_usb1_vbus>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb1_pins_a>;
-			disable-over-current;
-			status = "okay";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
-			phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
-			phy-reset-duration = <100>;
-			status = "okay";
-		};
-
-		mac1: ethernet@800f4000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac1_pins_a>;
-			status = "okay";
-		};
-	};
-
-	backlight {
-		compatible = "pwm-backlight";
-		pwms = <&pwm 3 5000000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <6>;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins_gpio>;
-
-		user1 {
-			label = "sd0-led";
-			gpios = <&gpio2 26 0>;
-			linux,default-trigger = "mmc0";
-		};
-
-		user2 {
-			label = "sd1-led";
-			gpios = <&gpio2 24 0>;
-			linux,default-trigger = "mmc2";
-		};
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-		reg_vddio_sd0: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "vddio-sd0";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio3 29 0>;
-		};
-
-		reg_vddio_sd1: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "vddio-sd1";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio2 19 0>;
-		};
-
-		reg_usb1_vbus: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "usb1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 8 0>;
-			enable-active-high;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-m28evk.dts b/arch/arm/boot/dts/imx28-m28evk.dts
deleted file mode 100644
index f3bddc5ada4b..000000000000
--- a/arch/arm/boot/dts/imx28-m28evk.dts
+++ /dev/null
@@ -1,271 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
-
- * Copyright (C) 2012 Marek Vasut <marex@denx.de>
- */
-
-/dts-v1/;
-#include "imx28-m28.dtsi"
-
-/ {
-	model = "Aries/DENX M28EVK";
-	compatible = "aries,m28evk", "denx,m28evk", "fsl,imx28";
-
-	apb@80000000 {
-		apbh@80000000 {
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_8bit_pins_a
-					     &mmc0_cd_cfg
-					     &mmc0_sck_cfg>;
-				bus-width = <8>;
-				wp-gpios = <&gpio3 10 0>;
-				vmmc-supply = <&reg_vddio_sd0>;
-				status = "okay";
-			};
-
-			ssp2: spi@80014000 {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				compatible = "fsl,imx28-spi";
-				pinctrl-names = "default";
-				pinctrl-0 = <&spi2_pins_a>;
-				status = "okay";
-
-				flash: m25p80@0 {
-					#address-cells = <1>;
-					#size-cells = <1>;
-					compatible = "m25p80", "jedec,spi-nor";
-					spi-max-frequency = <40000000>;
-					reg = <0>;
-				};
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_PWM3__GPIO_3_28
-						MX28_PAD_AUART2_CTS__GPIO_3_10
-						MX28_PAD_AUART2_RTS__GPIO_3_11
-						MX28_PAD_AUART3_RX__GPIO_3_12
-						MX28_PAD_AUART3_TX__GPIO_3_13
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_m28: lcdif-m28@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
-						MX28_PAD_LCD_ENABLE__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_24bit_pins_a
-					     &lcdif_pins_m28>;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <16>;
-					bus-width = <18>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <33260000>;
-							hactive = <800>;
-							vactive = <480>;
-							hback-porch = <0>;
-							hfront-porch = <256>;
-							vback-porch = <0>;
-							vfront-porch = <45>;
-							hsync-len = <1>;
-							vsync-len = <1>;
-							hsync-active = <0>;
-							vsync-active = <0>;
-							de-active = <1>;
-							pixelclk-active = <1>;
-						};
-					};
-				};
-			};
-
-			can0: can@80032000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&can0_pins_a>;
-				status = "okay";
-			};
-
-			can1: can@80034000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&can1_pins_a>;
-				status = "okay";
-			};
-		};
-
-		apbx@80040000 {
-			saif0: saif@80042000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&saif0_pins_a>;
-				status = "okay";
-			};
-
-			saif1: saif@80046000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&saif1_pins_a>;
-				fsl,saif-master = <&saif0>;
-				status = "okay";
-			};
-
-			i2c0: i2c@80058000 {
-				sgtl5000: codec@a {
-					compatible = "fsl,sgtl5000";
-					reg = <0x0a>;
-					#sound-dai-cells = <0>;
-					VDDA-supply = <&reg_3p3v>;
-					VDDIO-supply = <&reg_3p3v>;
-					clocks = <&saif0>;
-				};
-
-				eeprom: eeprom@51 {
-					compatible = "atmel,24c128";
-					reg = <0x51>;
-					pagesize = <32>;
-				};
-			};
-
-			lradc@80050000 {
-				status = "okay";
-				fsl,lradc-touchscreen-wires = <4>;
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-
-			usbphy1: usbphy@8007e000 {
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_pins_a>;
-				status = "okay";
-			};
-
-			auart1: serial@8006c000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart1_pins_a>;
-				status = "okay";
-			};
-
-			auart2: serial@8006e000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart2_2pins_b>;
-				status = "okay";
-			};
-
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm4_pins_a>;
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			vbus-supply = <&reg_usb0_vbus>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb0_pins_a>;
-			status = "okay";
-		};
-
-		usb1: usb@80090000 {
-			vbus-supply = <&reg_usb1_vbus>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb1_pins_a>;
-			status = "okay";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
-			clocks = <&clks 57>, <&clks 57>;
-			clock-names = "ipg", "ahb";
-			status = "okay";
-		};
-
-		mac1: ethernet@800f4000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac1_pins_a>;
-			status = "okay";
-		};
-	};
-
-	backlight {
-		compatible = "pwm-backlight";
-		pwms = <&pwm 4 5000000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <6>;
-	};
-
-	regulators {
-		reg_vddio_sd0: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "vddio-sd0";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio3 28 0>;
-		};
-
-		reg_usb0_vbus: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "usb0_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 12 0>;
-		};
-
-		reg_usb1_vbus: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "usb1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 13 0>;
-		};
-	};
-
-	sound {
-		compatible = "denx,m28evk-sgtl5000",
-			     "fsl,mxs-audio-sgtl5000";
-		model = "m28evk-sgtl5000";
-		saif-controllers = <&saif0 &saif1>;
-		audio-codec = <&sgtl5000>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-sps1.dts b/arch/arm/boot/dts/imx28-sps1.dts
deleted file mode 100644
index 43be7a6a769b..000000000000
--- a/arch/arm/boot/dts/imx28-sps1.dts
+++ /dev/null
@@ -1,166 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2012 Marek Vasut <marex@denx.de>
- */
-
-/dts-v1/;
-#include "imx28.dtsi"
-
-/ {
-	model = "SchulerControl GmbH, SC SPS 1";
-	compatible = "schulercontrol,imx28-sps1", "fsl,imx28";
-
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x08000000>;
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog-gpios@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_D00__GPIO_0_0
-						MX28_PAD_GPMI_D03__GPIO_0_3
-						MX28_PAD_GPMI_D06__GPIO_0_6
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-			};
-
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_4bit_pins_a>;
-				bus-width = <4>;
-				status = "okay";
-			};
-
-			ssp2: spi@80014000 {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				compatible = "fsl,imx28-spi";
-				pinctrl-names = "default";
-				pinctrl-0 = <&spi2_pins_a>;
-				status = "okay";
-
-				flash: m25p80@0 {
-					#address-cells = <1>;
-					#size-cells = <1>;
-					compatible = "everspin,mr25h256", "mr25h256";
-					spi-max-frequency = <40000000>;
-					reg = <0>;
-				};
-			};
-		};
-
-		apbx@80040000 {
-			i2c0: i2c@80058000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c0_pins_a>;
-				status = "okay";
-
-				rtc: rtc@51 {
-					compatible = "nxp,pcf8563";
-					reg = <0x51>;
-				};
-
-				eeprom: eeprom@52 {
-					compatible = "atmel,24c64";
-					reg = <0x52>;
-					pagesize = <32>;
-				};
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			usbphy0: usbphy@8007c000 {
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_pins_a>;
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb0: usb@80080000 {
-			vbus-supply = <&reg_usb0_vbus>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb0_pins_b>;
-			status = "okay";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
-			status = "okay";
-		};
-
-		mac1: ethernet@800f4000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac1_pins_a>;
-			status = "okay";
-		};
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_usb0_vbus: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "usb0_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 9 0>;
-		};
-	};
-
-	leds {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "gpio-leds";
-		status = "okay";
-
-		led@1 {
-			label = "sps1-1:yellow:user";
-			gpios = <&gpio0 6 0>;
-			linux,default-trigger = "heartbeat";
-			reg = <0>;
-		};
-
-		led@2 {
-			label = "sps1-2:red:user";
-			gpios = <&gpio0 3 0>;
-			linux,default-trigger = "heartbeat";
-			reg = <1>;
-		};
-
-		led@3 {
-			label = "sps1-3:red:user";
-			gpios = <&gpio0 0 0>;
-			default-trigger = "heartbeat";
-			reg = <2>;
-		};
-
-	};
-};
diff --git a/arch/arm/boot/dts/imx28-ts4600.dts b/arch/arm/boot/dts/imx28-ts4600.dts
deleted file mode 100644
index 097ec35c62d8..000000000000
--- a/arch/arm/boot/dts/imx28-ts4600.dts
+++ /dev/null
@@ -1,74 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2016 Savoir-Faire Linux
- * Author: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
- */
-
-/dts-v1/;
-#include "imx28.dtsi"
-#include "dt-bindings/gpio/gpio.h"
-
-/ {
-
-	model = "Technologic Systems i.MX28 TS-4600";
-	compatible = "technologic,imx28-ts4600", "fsl,imx28";
-
-	memory@40000000 {
-		device_type = "memory";
-		reg = <0x40000000 0x10000000>;   /* 256MB */
-	};
-
-	apb@80000000 {
-		apbh@80000000 {
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_4bit_pins_a
-					     &mmc0_sck_cfg
-					     &en_sd_pwr>;
-				broken-cd = <1>;
-				bus-width = <4>;
-				vmmc-supply = <&reg_vddio_sd0>;
-				status = "okay";
-			};
-
-			pinctrl@80018000 {
-
-				en_sd_pwr: en-sd-pwr@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_PWM3__GPIO_3_28
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-			};
-		};
-
-		apbx@80040000 {
-			pwm: pwm@80064000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pwm2_pins_a>;
-				status = "okay";
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-		};
-	};
-
-	reg_vddio_sd0: regulator-vddio-sd0 {
-		compatible = "regulator-fixed";
-		regulator-name = "vddio-sd0";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-boot-on;
-		gpio = <&gpio3 28 GPIO_ACTIVE_LOW>;
-	};
-
-};
diff --git a/arch/arm/boot/dts/imx35-eukrea-cpuimx35.dtsi b/arch/arm/boot/dts/imx35-eukrea-cpuimx35.dtsi
deleted file mode 100644
index 17bd2a97609a..000000000000
--- a/arch/arm/boot/dts/imx35-eukrea-cpuimx35.dtsi
+++ /dev/null
@@ -1,89 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2013 Eukréa Electromatique <denis@eukrea.com>
- */
-
-#include "imx35.dtsi"
-
-/ {
-	model = "Eukrea CPUIMX35";
-	compatible = "eukrea,cpuimx35", "fsl,imx35";
-
-	memory@80000000 {
-		device_type = "memory";
-		reg = <0x80000000 0x8000000>; /* 128M */
-	};
-};
-
-&fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_fec>;
-	status = "okay";
-};
-
-&i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c1>;
-	status = "okay";
-
-	pcf8563@51 {
-		compatible = "nxp,pcf8563";
-		reg = <0x51>;
-	};
-
-	tsc2007: tsc2007@48 {
-		compatible = "ti,tsc2007";
-		gpios = <&gpio3 2 0>;
-		interrupt-parent = <&gpio3>;
-		interrupts = <0x2 0x8>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_tsc2007_1>;
-		reg = <0x48>;
-		ti,x-plate-ohms = <180>;
-	};
-};
-
-&iomuxc {
-	imx35-eukrea {
-		pinctrl_fec: fecgrp {
-			fsl,pins = <
-				MX35_PAD_FEC_TX_CLK__FEC_TX_CLK		0x80000000
-				MX35_PAD_FEC_RX_CLK__FEC_RX_CLK		0x80000000
-				MX35_PAD_FEC_RX_DV__FEC_RX_DV		0x80000000
-				MX35_PAD_FEC_COL__FEC_COL		0x80000000
-				MX35_PAD_FEC_RDATA0__FEC_RDATA_0	0x80000000
-				MX35_PAD_FEC_TDATA0__FEC_TDATA_0	0x80000000
-				MX35_PAD_FEC_TX_EN__FEC_TX_EN		0x80000000
-				MX35_PAD_FEC_MDC__FEC_MDC		0x80000000
-				MX35_PAD_FEC_MDIO__FEC_MDIO		0x80000000
-				MX35_PAD_FEC_TX_ERR__FEC_TX_ERR		0x80000000
-				MX35_PAD_FEC_RX_ERR__FEC_RX_ERR		0x80000000
-				MX35_PAD_FEC_CRS__FEC_CRS		0x80000000
-				MX35_PAD_FEC_RDATA1__FEC_RDATA_1	0x80000000
-				MX35_PAD_FEC_TDATA1__FEC_TDATA_1	0x80000000
-				MX35_PAD_FEC_RDATA2__FEC_RDATA_2	0x80000000
-				MX35_PAD_FEC_TDATA2__FEC_TDATA_2	0x80000000
-				MX35_PAD_FEC_RDATA3__FEC_RDATA_3	0x80000000
-				MX35_PAD_FEC_TDATA3__FEC_TDATA_3	0x80000000
-			>;
-		};
-
-		pinctrl_i2c1: i2c1grp {
-			fsl,pins = <
-				MX35_PAD_I2C1_CLK__I2C1_SCL		0x80000000
-				MX35_PAD_I2C1_DAT__I2C1_SDA		0x80000000
-			>;
-		};
-
-		pinctrl_tsc2007_1: tsc2007grp-1 {
-			fsl,pins = <MX35_PAD_ATA_DA2__GPIO3_2 0x80000000>;
-		};
-	};
-};
-
-&nfc {
-	nand-bus-width = <8>;
-	nand-ecc-mode = "hw";
-	nand-on-flash-bbt;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx51-apf51.dts b/arch/arm/boot/dts/imx51-apf51.dts
deleted file mode 100644
index ba28ffe06fe2..000000000000
--- a/arch/arm/boot/dts/imx51-apf51.dts
+++ /dev/null
@@ -1,84 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2012 Armadeus Systems - <support@armadeus.com>
- * Copyright 2012 Laurent Cans <laurent.cans@gmail.com>
- *
- * Based on mx51-babbage.dts
- * Copyright 2011 Freescale Semiconductor, Inc.
- * Copyright 2011 Linaro Ltd.
- */
-
-/dts-v1/;
-#include "imx51.dtsi"
-
-/ {
-	model = "Armadeus Systems APF51 module";
-	compatible = "armadeus,imx51-apf51", "fsl,imx51";
-
-	memory@90000000 {
-		device_type = "memory";
-		reg = <0x90000000 0x20000000>;
-	};
-
-	clocks {
-		osc {
-			clock-frequency = <33554432>;
-		};
-	};
-};
-
-&fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_fec>;
-	phy-mode = "mii";
-	phy-reset-gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
-	phy-reset-duration = <1>;
-	status = "okay";
-};
-
-&iomuxc {
-	imx51-apf51 {
-		pinctrl_fec: fecgrp {
-			fsl,pins = <
-				MX51_PAD_DI_GP3__FEC_TX_ER		0x80000000
-				MX51_PAD_DI2_PIN4__FEC_CRS		0x80000000
-				MX51_PAD_DI2_PIN2__FEC_MDC		0x80000000
-				MX51_PAD_DI2_PIN3__FEC_MDIO		0x80000000
-				MX51_PAD_DI2_DISP_CLK__FEC_RDATA1	0x80000000
-				MX51_PAD_DI_GP4__FEC_RDATA2		0x80000000
-				MX51_PAD_DISP2_DAT0__FEC_RDATA3		0x80000000
-				MX51_PAD_DISP2_DAT1__FEC_RX_ER		0x80000000
-				MX51_PAD_DISP2_DAT6__FEC_TDATA1		0x80000000
-				MX51_PAD_DISP2_DAT7__FEC_TDATA2		0x80000000
-				MX51_PAD_DISP2_DAT8__FEC_TDATA3		0x80000000
-				MX51_PAD_DISP2_DAT9__FEC_TX_EN		0x80000000
-				MX51_PAD_DISP2_DAT10__FEC_COL		0x80000000
-				MX51_PAD_DISP2_DAT11__FEC_RX_CLK	0x80000000
-				MX51_PAD_DISP2_DAT12__FEC_RX_DV		0x80000000
-				MX51_PAD_DISP2_DAT13__FEC_TX_CLK	0x80000000
-				MX51_PAD_DISP2_DAT14__FEC_RDATA0	0x80000000
-				MX51_PAD_DISP2_DAT15__FEC_TDATA0	0x80000000
-			>;
-		};
-
-		pinctrl_uart3: uart3grp {
-			fsl,pins = <
-				MX51_PAD_UART3_RXD__UART3_RXD		0x1c5
-				MX51_PAD_UART3_TXD__UART3_TXD		0x1c5
-			>;
-		};
-	};
-};
-
-&nfc {
-	nand-bus-width = <8>;
-	nand-ecc-mode = "hw";
-	nand-on-flash-bbt;
-	status = "okay";
-};
-
-&uart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart3>;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx51-apf51dev.dts b/arch/arm/boot/dts/imx51-apf51dev.dts
deleted file mode 100644
index c66f274ba4e9..000000000000
--- a/arch/arm/boot/dts/imx51-apf51dev.dts
+++ /dev/null
@@ -1,217 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2013 Armadeus Systems - <support@armadeus.com>
- */
-
-/* APF51Dev is a docking board for the APF51 SOM */
-#include "imx51-apf51.dts"
-
-/ {
-	model = "Armadeus Systems APF51Dev docking/development board";
-	compatible = "armadeus,imx51-apf51dev", "armadeus,imx51-apf51", "fsl,imx51";
-
-	backlight {
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_backlight>;
-		compatible = "gpio-backlight";
-		gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>;
-		default-on;
-	};
-
-	disp1 {
-		compatible = "fsl,imx-parallel-display";
-		interface-pix-fmt = "bgr666";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_ipu_disp1>;
-
-		display-timings {
-			lw700 {
-				native-mode;
-				clock-frequency = <33000033>;
-				hactive = <800>;
-				vactive = <480>;
-				hback-porch = <96>;
-				hfront-porch = <96>;
-				vback-porch = <20>;
-				vfront-porch = <21>;
-				hsync-len = <64>;
-				vsync-len = <4>;
-				hsync-active = <1>;
-				vsync-active = <1>;
-				de-active = <1>;
-				pixelclk-active = <0>;
-			};
-		};
-
-		port {
-			display_in: endpoint {
-				remote-endpoint = <&ipu_di0_disp1>;
-			};
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		user-key {
-			label = "user";
-			gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
-			linux,code = <256>; /* BTN_0 */
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		user {
-			label = "Heartbeat";
-			gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-		};
-	};
-};
-
-&ecspi1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi1>;
-	cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>,
-		   <&gpio4 25 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-&ecspi2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi2>;
-	cs-gpios = <&gpio3 28 GPIO_ACTIVE_LOW>,
-		   <&gpio3 27 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-&esdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_esdhc1>;
-	cd-gpios = <&gpio2 29 GPIO_ACTIVE_LOW>;
-	bus-width = <4>;
-	status = "okay";
-};
-
-&esdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_esdhc2>;
-	bus-width = <4>;
-	non-removable;
-	status = "okay";
-};
-
-&i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c2>;
-	status = "okay";
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_hog>;
-
-	imx51-apf51dev {
-		pinctrl_backlight: backlightgrp {
-			fsl,pins = <
-				MX51_PAD_DI1_D1_CS__GPIO3_4 0x1F5
-			>;
-		};
-
-		pinctrl_hog: hoggrp {
-			fsl,pins = <
-				MX51_PAD_EIM_EB2__GPIO2_22   0x0C5
-				MX51_PAD_EIM_EB3__GPIO2_23   0x0C5
-				MX51_PAD_EIM_CS4__GPIO2_29   0x100
-				MX51_PAD_NANDF_D13__GPIO3_27 0x0C5
-				MX51_PAD_NANDF_D12__GPIO3_28 0x0C5
-				MX51_PAD_CSPI1_SS0__GPIO4_24 0x0C5
-				MX51_PAD_CSPI1_SS1__GPIO4_25 0x0C5
-				MX51_PAD_GPIO1_2__GPIO1_2    0x0C5
-				MX51_PAD_GPIO1_3__GPIO1_3    0x0C5
-			>;
-		};
-
-		pinctrl_ecspi1: ecspi1grp {
-			fsl,pins = <
-				MX51_PAD_CSPI1_MISO__ECSPI1_MISO	0x185
-				MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI	0x185
-				MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK	0x185
-			>;
-		};
-
-		pinctrl_ecspi2: ecspi2grp {
-			fsl,pins = <
-				MX51_PAD_NANDF_RB3__ECSPI2_MISO		0x185
-				MX51_PAD_NANDF_D15__ECSPI2_MOSI		0x185
-				MX51_PAD_NANDF_RB2__ECSPI2_SCLK		0x185
-			>;
-		};
-
-		pinctrl_esdhc1: esdhc1grp {
-			fsl,pins = <
-				MX51_PAD_SD1_CMD__SD1_CMD		0x400020d5
-				MX51_PAD_SD1_CLK__SD1_CLK		0x20d5
-				MX51_PAD_SD1_DATA0__SD1_DATA0		0x20d5
-				MX51_PAD_SD1_DATA1__SD1_DATA1		0x20d5
-				MX51_PAD_SD1_DATA2__SD1_DATA2		0x20d5
-				MX51_PAD_SD1_DATA3__SD1_DATA3		0x20d5
-			>;
-		};
-
-		pinctrl_esdhc2: esdhc2grp {
-			fsl,pins = <
-				MX51_PAD_SD2_CMD__SD2_CMD		0x400020d5
-				MX51_PAD_SD2_CLK__SD2_CLK		0x20d5
-				MX51_PAD_SD2_DATA0__SD2_DATA0		0x20d5
-				MX51_PAD_SD2_DATA1__SD2_DATA1		0x20d5
-				MX51_PAD_SD2_DATA2__SD2_DATA2		0x20d5
-				MX51_PAD_SD2_DATA3__SD2_DATA3		0x20d5
-			>;
-		};
-
-		pinctrl_i2c2: i2c2grp {
-			fsl,pins = <
-				MX51_PAD_EIM_D27__I2C2_SCL		0x400001ed
-				MX51_PAD_EIM_D24__I2C2_SDA		0x400001ed
-			>;
-		};
-
-		pinctrl_ipu_disp1: ipudisp1grp {
-			fsl,pins = <
-				MX51_PAD_DISP1_DAT0__DISP1_DAT0		0x5
-				MX51_PAD_DISP1_DAT1__DISP1_DAT1		0x5
-				MX51_PAD_DISP1_DAT2__DISP1_DAT2		0x5
-				MX51_PAD_DISP1_DAT3__DISP1_DAT3		0x5
-				MX51_PAD_DISP1_DAT4__DISP1_DAT4		0x5
-				MX51_PAD_DISP1_DAT5__DISP1_DAT5		0x5
-				MX51_PAD_DISP1_DAT6__DISP1_DAT6		0x5
-				MX51_PAD_DISP1_DAT7__DISP1_DAT7		0x5
-				MX51_PAD_DISP1_DAT8__DISP1_DAT8		0x5
-				MX51_PAD_DISP1_DAT9__DISP1_DAT9		0x5
-				MX51_PAD_DISP1_DAT10__DISP1_DAT10	0x5
-				MX51_PAD_DISP1_DAT11__DISP1_DAT11	0x5
-				MX51_PAD_DISP1_DAT12__DISP1_DAT12	0x5
-				MX51_PAD_DISP1_DAT13__DISP1_DAT13	0x5
-				MX51_PAD_DISP1_DAT14__DISP1_DAT14	0x5
-				MX51_PAD_DISP1_DAT15__DISP1_DAT15	0x5
-				MX51_PAD_DISP1_DAT16__DISP1_DAT16	0x5
-				MX51_PAD_DISP1_DAT17__DISP1_DAT17	0x5
-				MX51_PAD_DISP1_DAT18__DISP1_DAT18	0x5
-				MX51_PAD_DISP1_DAT19__DISP1_DAT19	0x5
-				MX51_PAD_DISP1_DAT20__DISP1_DAT20	0x5
-				MX51_PAD_DISP1_DAT21__DISP1_DAT21	0x5
-				MX51_PAD_DISP1_DAT22__DISP1_DAT22	0x5
-				MX51_PAD_DISP1_DAT23__DISP1_DAT23	0x5
-				MX51_PAD_DI1_PIN2__DI1_PIN2		0x5
-				MX51_PAD_DI1_PIN3__DI1_PIN3		0x5
-			>;
-		};
-	};
-};
-
-&ipu_di0_disp1 {
-	remote-endpoint = <&display_in>;
-};
diff --git a/arch/arm/boot/dts/imx51-digi-connectcore-jsk.dts b/arch/arm/boot/dts/imx51-digi-connectcore-jsk.dts
deleted file mode 100644
index aab8d6f137c3..000000000000
--- a/arch/arm/boot/dts/imx51-digi-connectcore-jsk.dts
+++ /dev/null
@@ -1,118 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2014 Alexander Shiyan <shc_work@mail.ru>
- */
-
-#include "imx51-digi-connectcore-som.dtsi"
-
-/ {
-	model = "Digi ConnectCore CC(W)-MX51 JSK";
-	compatible = "digi,connectcore-ccxmx51-jsk",
-		     "digi,connectcore-ccxmx51-som", "fsl,imx51";
-
-	chosen {
-		stdout-path = &uart1;
-	};
-};
-
-&esdhc1 {
-	status = "okay";
-};
-
-&owire {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_owire>;
-	status = "okay";
-};
-
-&pmic {
-	fsl,mc13xxx-uses-rtc;
-
-	regulators {
-		vcoincell_reg: vcoincell {
-			regulator-min-microvolt = <3000000>;
-			regulator-max-microvolt = <3000000>;
-			regulator-always-on;
-		};
-	};
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
-	status = "okay";
-};
-
-&uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
-	status = "okay";
-};
-
-&uart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart3>;
-	status = "okay";
-};
-
-&usbotg {
-	dr_mode = "otg";
-	status = "okay";
-};
-
-&usbh1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbh1>;
-	dr_mode = "host";
-	phy_type = "ulpi";
-	disable-over-current;
-	status = "okay";
-};
-
-&iomuxc {
-	imx51-digi-connectcore-jsk {
-		pinctrl_owire: owiregrp {
-			fsl,pins = <
-				MX51_PAD_OWIRE_LINE__OWIRE_LINE		0x40000000
-			>;
-		};
-
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX51_PAD_UART1_RXD__UART1_RXD		0x1c5
-				MX51_PAD_UART1_TXD__UART1_TXD		0x1c5
-			>;
-		};
-
-		pinctrl_uart2: uart2grp {
-			fsl,pins = <
-				MX51_PAD_UART2_RXD__UART2_RXD		0x1c5
-				MX51_PAD_UART2_TXD__UART2_TXD		0x1c5
-			>;
-		};
-
-		pinctrl_uart3: uart3grp {
-			fsl,pins = <
-				MX51_PAD_UART3_RXD__UART3_RXD		0x1c5
-				MX51_PAD_UART3_TXD__UART3_TXD		0x1c5
-			>;
-		};
-
-		pinctrl_usbh1: usbh1grp {
-			fsl,pins = <
-				MX51_PAD_USBH1_DATA0__USBH1_DATA0	0x1e5
-				MX51_PAD_USBH1_DATA1__USBH1_DATA1	0x1e5
-				MX51_PAD_USBH1_DATA2__USBH1_DATA2	0x1e5
-				MX51_PAD_USBH1_DATA3__USBH1_DATA3	0x1e5
-				MX51_PAD_USBH1_DATA4__USBH1_DATA4	0x1e5
-				MX51_PAD_USBH1_DATA5__USBH1_DATA5	0x1e5
-				MX51_PAD_USBH1_DATA6__USBH1_DATA6	0x1e5
-				MX51_PAD_USBH1_DATA7__USBH1_DATA7	0x1e5
-				MX51_PAD_USBH1_CLK__USBH1_CLK		0x1e5
-				MX51_PAD_USBH1_DIR__USBH1_DIR		0x1e5
-				MX51_PAD_USBH1_NXT__USBH1_NXT		0x1e5
-				MX51_PAD_USBH1_STP__USBH1_STP		0x1e5
-			>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx51-digi-connectcore-som.dtsi b/arch/arm/boot/dts/imx51-digi-connectcore-som.dtsi
deleted file mode 100644
index 7d4970417dce..000000000000
--- a/arch/arm/boot/dts/imx51-digi-connectcore-som.dtsi
+++ /dev/null
@@ -1,389 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2014 Alexander Shiyan <shc_work@mail.ru>
- */
-
-/dts-v1/;
-#include "imx51.dtsi"
-
-/ {
-	model = "Digi ConnectCore CC(W)-MX51";
-	compatible = "digi,connectcore-ccxmx51-som", "fsl,imx51";
-
-	memory@90000000 {
-		device_type = "memory";
-		reg = <0x90000000 0x08000000>;
-	};
-};
-
-&ecspi1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi1>;
-	cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
-	status = "okay";
-
-	pmic: mc13892@0 {
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_mc13892>;
-		compatible = "fsl,mc13892";
-		spi-max-frequency = <16000000>;
-		spi-cs-high;
-		reg = <0>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
-
-		regulators {
-			sw1_reg: sw1 {
-				regulator-min-microvolt = <1000000>;
-				regulator-max-microvolt = <1100000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			sw2_reg: sw2 {
-				regulator-min-microvolt = <1225000>;
-				regulator-max-microvolt = <1225000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			sw3_reg: sw3 {
-				regulator-min-microvolt = <1200000>;
-				regulator-max-microvolt = <1200000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			swbst_reg: swbst { };
-
-			viohi_reg: viohi {
-				regulator-always-on;
-			};
-
-			vpll_reg: vpll {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-always-on;
-			};
-
-			vdig_reg: vdig {
-				regulator-min-microvolt = <1250000>;
-				regulator-max-microvolt = <1250000>;
-				regulator-always-on;
-			};
-
-			vsd_reg: vsd {
-				regulator-min-microvolt = <3150000>;
-				regulator-max-microvolt = <3150000>;
-				regulator-always-on;
-			};
-
-			vusb2_reg: vusb2 {
-				regulator-min-microvolt = <2600000>;
-				regulator-max-microvolt = <2600000>;
-				regulator-always-on;
-			};
-
-			vvideo_reg: vvideo {
-				regulator-min-microvolt = <2775000>;
-				regulator-max-microvolt = <2775000>;
-				regulator-always-on;
-			};
-
-			vaudio_reg: vaudio {
-				regulator-min-microvolt = <3000000>;
-				regulator-max-microvolt = <3000000>;
-				regulator-always-on;
-			};
-
-			vcam_reg: vcam {
-				regulator-min-microvolt = <2750000>;
-				regulator-max-microvolt = <2750000>;
-				regulator-always-on;
-			};
-
-			vgen1_reg: vgen1 {
-				regulator-min-microvolt = <1200000>;
-				regulator-max-microvolt = <1200000>;
-				regulator-always-on;
-			};
-
-			vgen2_reg: vgen2 {
-				regulator-min-microvolt = <3150000>;
-				regulator-max-microvolt = <3150000>;
-				regulator-always-on;
-			};
-
-			vgen3_reg: vgen3 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-always-on;
-			};
-
-			vusb_reg: vusb {
-				regulator-always-on;
-			};
-
-			gpo1_reg: gpo1 { };
-
-			gpo2_reg: gpo2 { };
-
-			gpo3_reg: gpo3 { };
-
-			gpo4_reg: gpo4 { };
-
-			pwgt2spi_reg: pwgt2spi {
-				regulator-always-on;
-			};
-		};
-	};
-};
-
-&esdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_esdhc1>;
-	max-frequency = <50000000>;
-	bus-width = <1>;
-};
-
-&esdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_esdhc2>;
-	cap-sdio-irq;
-	wakeup-source;
-	keep-power-in-suspend;
-	max-frequency = <50000000>;
-	no-1-8-v;
-	non-removable;
-	vmmc-supply = <&gpo4_reg>;
-	status = "okay";
-};
-
-&fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_fec>;
-	phy-mode = "mii";
-	phy-supply = <&gpo3_reg>;
-	/* Pins shared with LCD2, keep status disabled */
-};
-
-&i2c2 {
-	pinctrl-names = "default", "gpio";
-	pinctrl-0 = <&pinctrl_i2c2>;
-	pinctrl-1 = <&pinctrl_i2c2_gpio>;
-	clock-frequency = <400000>;
-	scl-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
-	sda-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
-	status = "okay";
-
-	mma7455l@1d {
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_mma7455l>;
-		compatible = "fsl,mma7455l";
-		reg = <0x1d>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <7 IRQ_TYPE_LEVEL_HIGH>, <6 IRQ_TYPE_LEVEL_HIGH>;
-	};
-};
-
-&nfc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_nfc>;
-	nand-bus-width = <8>;
-	nand-ecc-mode = "hw";
-	nand-on-flash-bbt;
-	status = "okay";
-};
-
-&usbotg {
-	phy_type = "utmi_wide";
-	disable-over-current;
-	/* Device role is not known, keep status disabled */
-};
-
-&weim {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_weim>;
-	status = "okay";
-
-	lan9221: ethernet@5,0 {
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_lan9221>;
-		compatible = "smsc,lan9221", "smsc,lan9115";
-		reg = <5 0x00000000 0x1000>;
-		fsl,weim-cs-timing = <
-			0x00420081 0x00000000
-			0x32260000 0x00000000
-			0x72080f00 0x00000000
-		>;
-		clocks = <&clks IMX5_CLK_DUMMY>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
-		phy-mode = "mii";
-		reg-io-width = <2>;
-		smsc,irq-push-pull;
-		vdd33a-supply = <&gpo2_reg>;
-		vddvario-supply = <&gpo2_reg>;
-	};
-};
-
-&iomuxc {
-	imx51-digi-connectcore-som {
-		pinctrl_ecspi1: ecspi1grp {
-			fsl,pins = <
-				MX51_PAD_CSPI1_MISO__ECSPI1_MISO	0x185
-				MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI	0x185
-				MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK	0x185
-				MX51_PAD_CSPI1_SS0__GPIO4_24		0x85 /* CS0 */
-			>;
-		};
-
-		pinctrl_esdhc1: esdhc1grp {
-			fsl,pins = <
-				MX51_PAD_SD1_CLK__SD1_CLK		0x400021d5
-				MX51_PAD_SD1_CMD__SD1_CMD		0x400020d5
-				MX51_PAD_SD1_DATA0__SD1_DATA0		0x400020d5
-			>;
-		};
-
-		pinctrl_esdhc2: esdhc2grp {
-			fsl,pins = <
-				MX51_PAD_SD2_CMD__SD2_CMD		0x400020d5
-				MX51_PAD_SD2_CLK__SD2_CLK		0x20d5
-				MX51_PAD_SD2_DATA0__SD2_DATA0		0x20d5
-				MX51_PAD_SD2_DATA1__SD2_DATA1		0x20d5
-				MX51_PAD_SD2_DATA2__SD2_DATA2		0x20d5
-				MX51_PAD_SD2_DATA3__SD2_DATA3		0x20d5
-			>;
-		};
-
-		pinctrl_fec: fecgrp {
-			fsl,pins = <
-				MX51_PAD_DI_GP3__FEC_TX_ER		0x80000000
-				MX51_PAD_DI2_PIN4__FEC_CRS		0x80000000
-				MX51_PAD_DI2_PIN2__FEC_MDC		0x80000000
-				MX51_PAD_DI2_PIN3__FEC_MDIO		0x80000000
-				MX51_PAD_DI2_DISP_CLK__FEC_RDATA1	0x80000000
-				MX51_PAD_DI_GP4__FEC_RDATA2		0x80000000
-				MX51_PAD_DISP2_DAT0__FEC_RDATA3		0x80000000
-				MX51_PAD_DISP2_DAT1__FEC_RX_ER		0x80000000
-				MX51_PAD_DISP2_DAT6__FEC_TDATA1		0x80000000
-				MX51_PAD_DISP2_DAT7__FEC_TDATA2		0x80000000
-				MX51_PAD_DISP2_DAT8__FEC_TDATA3		0x80000000
-				MX51_PAD_DISP2_DAT9__FEC_TX_EN		0x80000000
-				MX51_PAD_DISP2_DAT10__FEC_COL		0x80000000
-				MX51_PAD_DISP2_DAT11__FEC_RX_CLK	0x80000000
-				MX51_PAD_DISP2_DAT12__FEC_RX_DV		0x80000000
-				MX51_PAD_DISP2_DAT13__FEC_TX_CLK	0x80000000
-				MX51_PAD_DISP2_DAT14__FEC_RDATA0	0x80000000
-				MX51_PAD_DISP2_DAT15__FEC_TDATA0	0x80000000
-			>;
-		};
-
-		pinctrl_i2c2: i2c2grp {
-			fsl,pins = <
-				MX51_PAD_GPIO1_2__I2C2_SCL		0x400001ed
-				MX51_PAD_GPIO1_3__I2C2_SDA		0x400001ed
-			>;
-		};
-
-		pinctrl_i2c2_gpio: i2c2gpiogrp {
-			fsl,pins = <
-				MX51_PAD_GPIO1_2__GPIO1_2		0x400001ed
-				MX51_PAD_GPIO1_3__GPIO1_3		0x400001ed
-			>;
-		};
-
-		pinctrl_nfc: nfcgrp {
-			fsl,pins = <
-				MX51_PAD_NANDF_D0__NANDF_D0		0x80000000
-				MX51_PAD_NANDF_D1__NANDF_D1		0x80000000
-				MX51_PAD_NANDF_D2__NANDF_D2		0x80000000
-				MX51_PAD_NANDF_D3__NANDF_D3		0x80000000
-				MX51_PAD_NANDF_D4__NANDF_D4		0x80000000
-				MX51_PAD_NANDF_D5__NANDF_D5		0x80000000
-				MX51_PAD_NANDF_D6__NANDF_D6		0x80000000
-				MX51_PAD_NANDF_D7__NANDF_D7		0x80000000
-				MX51_PAD_NANDF_ALE__NANDF_ALE		0x80000000
-				MX51_PAD_NANDF_CLE__NANDF_CLE		0x80000000
-				MX51_PAD_NANDF_RE_B__NANDF_RE_B		0x80000000
-				MX51_PAD_NANDF_WE_B__NANDF_WE_B		0x80000000
-				MX51_PAD_NANDF_WP_B__NANDF_WP_B		0x80000000
-				MX51_PAD_NANDF_CS0__NANDF_CS0		0x80000000
-				MX51_PAD_NANDF_RB0__NANDF_RB0		0x80000000
-			>;
-		};
-
-		pinctrl_lan9221: lan9221grp {
-			fsl,pins = <
-				MX51_PAD_GPIO1_9__GPIO1_9		0xe5 /* IRQ */
-			>;
-		};
-
-		pinctrl_mc13892: mc13892grp {
-			fsl,pins = <
-				MX51_PAD_GPIO1_5__GPIO1_5		0xe5 /* IRQ */
-			>;
-		};
-
-		pinctrl_mma7455l: mma7455lgrp {
-			fsl,pins = <
-				MX51_PAD_GPIO1_7__GPIO1_7		0xe5 /* IRQ1 */
-				MX51_PAD_GPIO1_6__GPIO1_6		0xe5 /* IRQ2 */
-			>;
-		};
-
-		pinctrl_weim: weimgrp {
-			fsl,pins = <
-				MX51_PAD_EIM_DA0__EIM_DA0		0x80000000
-				MX51_PAD_EIM_DA1__EIM_DA1		0x80000000
-				MX51_PAD_EIM_DA2__EIM_DA2		0x80000000
-				MX51_PAD_EIM_DA3__EIM_DA3		0x80000000
-				MX51_PAD_EIM_DA4__EIM_DA4		0x80000000
-				MX51_PAD_EIM_DA5__EIM_DA5		0x80000000
-				MX51_PAD_EIM_DA6__EIM_DA6		0x80000000
-				MX51_PAD_EIM_DA7__EIM_DA7		0x80000000
-				MX51_PAD_EIM_DA8__EIM_DA8		0x80000000
-				MX51_PAD_EIM_DA9__EIM_DA9		0x80000000
-				MX51_PAD_EIM_DA10__EIM_DA10		0x80000000
-				MX51_PAD_EIM_DA11__EIM_DA11		0x80000000
-				MX51_PAD_EIM_DA12__EIM_DA12		0x80000000
-				MX51_PAD_EIM_DA13__EIM_DA13		0x80000000
-				MX51_PAD_EIM_DA14__EIM_DA14		0x80000000
-				MX51_PAD_EIM_DA15__EIM_DA15		0x80000000
-				MX51_PAD_EIM_A16__EIM_A16		0x80000000
-				MX51_PAD_EIM_A17__EIM_A17		0x80000000
-				MX51_PAD_EIM_A18__EIM_A18		0x80000000
-				MX51_PAD_EIM_A19__EIM_A19		0x80000000
-				MX51_PAD_EIM_A20__EIM_A20		0x80000000
-				MX51_PAD_EIM_A21__EIM_A21		0x80000000
-				MX51_PAD_EIM_A22__EIM_A22		0x80000000
-				MX51_PAD_EIM_A23__EIM_A23		0x80000000
-				MX51_PAD_EIM_A24__EIM_A24		0x80000000
-				MX51_PAD_EIM_A25__EIM_A25		0x80000000
-				MX51_PAD_EIM_A26__EIM_A26		0x80000000
-				MX51_PAD_EIM_A27__EIM_A27		0x80000000
-				MX51_PAD_EIM_D16__EIM_D16		0x80000000
-				MX51_PAD_EIM_D17__EIM_D17		0x80000000
-				MX51_PAD_EIM_D18__EIM_D18		0x80000000
-				MX51_PAD_EIM_D19__EIM_D19		0x80000000
-				MX51_PAD_EIM_D20__EIM_D20		0x80000000
-				MX51_PAD_EIM_D21__EIM_D21		0x80000000
-				MX51_PAD_EIM_D22__EIM_D22		0x80000000
-				MX51_PAD_EIM_D23__EIM_D23		0x80000000
-				MX51_PAD_EIM_D24__EIM_D24		0x80000000
-				MX51_PAD_EIM_D25__EIM_D25		0x80000000
-				MX51_PAD_EIM_D26__EIM_D26		0x80000000
-				MX51_PAD_EIM_D27__EIM_D27		0x80000000
-				MX51_PAD_EIM_D28__EIM_D28		0x80000000
-				MX51_PAD_EIM_D29__EIM_D29		0x80000000
-				MX51_PAD_EIM_D30__EIM_D30		0x80000000
-				MX51_PAD_EIM_D31__EIM_D31		0x80000000
-				MX51_PAD_EIM_OE__EIM_OE			0x80000000
-				MX51_PAD_EIM_DTACK__EIM_DTACK		0x80000000
-				MX51_PAD_EIM_LBA__EIM_LBA		0x80000000
-				MX51_PAD_EIM_CS5__EIM_CS5		0x80000000 /* CS5 */
-			>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx51-eukrea-cpuimx51.dtsi b/arch/arm/boot/dts/imx51-eukrea-cpuimx51.dtsi
deleted file mode 100644
index c2a929ba8ceb..000000000000
--- a/arch/arm/boot/dts/imx51-eukrea-cpuimx51.dtsi
+++ /dev/null
@@ -1,92 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2013 Eukréa Electromatique <denis@eukrea.com>
- */
-
-#include "imx51.dtsi"
-
-/ {
-	model = "Eukrea CPUIMX51";
-	compatible = "eukrea,cpuimx51", "fsl,imx51";
-
-	memory@90000000 {
-		device_type = "memory";
-		reg = <0x90000000 0x10000000>; /* 256M */
-	};
-};
-
-&fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_fec>;
-	status = "okay";
-};
-
-&i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c1>;
-	status = "okay";
-
-	pcf8563@51 {
-		compatible = "nxp,pcf8563";
-		reg = <0x51>;
-	};
-
-	tsc2007: tsc2007@49 {
-		compatible = "ti,tsc2007";
-		gpios = <&gpio4 0 1>;
-		interrupt-parent = <&gpio4>;
-		interrupts = <0x0 0x8>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_tsc2007_1>;
-		reg = <0x49>;
-		ti,x-plate-ohms = <180>;
-	};
-};
-
-&iomuxc {
-	imx51-eukrea {
-		pinctrl_tsc2007_1: tsc2007grp-1 {
-			fsl,pins = <
-				MX51_PAD_GPIO_NAND__GPIO_NAND 0x1f5
-				MX51_PAD_NANDF_D8__GPIO4_0 0x1f5
-			>;
-		};
-
-		pinctrl_fec: fecgrp {
-			fsl,pins = <
-				MX51_PAD_DI_GP3__FEC_TX_ER		0x80000000
-				MX51_PAD_DI2_PIN4__FEC_CRS		0x80000000
-				MX51_PAD_DI2_PIN2__FEC_MDC		0x80000000
-				MX51_PAD_DI2_PIN3__FEC_MDIO		0x80000000
-				MX51_PAD_DI2_DISP_CLK__FEC_RDATA1	0x80000000
-				MX51_PAD_DI_GP4__FEC_RDATA2		0x80000000
-				MX51_PAD_DISP2_DAT0__FEC_RDATA3		0x80000000
-				MX51_PAD_DISP2_DAT1__FEC_RX_ER		0x80000000
-				MX51_PAD_DISP2_DAT6__FEC_TDATA1		0x80000000
-				MX51_PAD_DISP2_DAT7__FEC_TDATA2		0x80000000
-				MX51_PAD_DISP2_DAT8__FEC_TDATA3		0x80000000
-				MX51_PAD_DISP2_DAT9__FEC_TX_EN		0x80000000
-				MX51_PAD_DISP2_DAT10__FEC_COL		0x80000000
-				MX51_PAD_DISP2_DAT11__FEC_RX_CLK	0x80000000
-				MX51_PAD_DISP2_DAT12__FEC_RX_DV		0x80000000
-				MX51_PAD_DISP2_DAT13__FEC_TX_CLK	0x80000000
-				MX51_PAD_DISP2_DAT14__FEC_RDATA0	0x80000000
-				MX51_PAD_DISP2_DAT15__FEC_TDATA0	0x80000000
-			>;
-		};
-
-		pinctrl_i2c1: i2c1grp {
-			fsl,pins = <
-				MX51_PAD_SD2_CMD__I2C1_SCL		0x400001ed
-				MX51_PAD_SD2_CLK__I2C1_SDA		0x400001ed
-			>;
-		};
-	};
-};
-
-&nfc {
-	nand-bus-width = <8>;
-	nand-ecc-mode = "hw";
-	nand-on-flash-bbt;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard.dts b/arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard.dts
deleted file mode 100644
index b6d931e96a8f..000000000000
--- a/arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard.dts
+++ /dev/null
@@ -1,274 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2013 Eukréa Electromatique <denis@eukrea.com>
- */
-
-/dts-v1/;
-#include "imx51-eukrea-cpuimx51.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
-	model = "Eukrea CPUIMX51";
-	compatible = "eukrea,mbimxsd51","eukrea,cpuimx51", "fsl,imx51";
-
-	clocks {
-		clk24M: can_clock {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <24000000>;
-		};
-	};
-
-	gpio_keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpiokeys_1>;
-
-		button-1 {
-			label = "BP1";
-			gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;
-			linux,code = <256>;
-			wakeup-source;
-			linux,input-type = <1>;
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpioled>;
-
-		led1 {
-			label = "led1";
-			gpios = <&gpio3 30 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "heartbeat";
-		};
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_can: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "CAN_RST";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
-			startup-delay-us = <20000>;
-			enable-active-high;
-		};
-	};
-
-	sound {
-		compatible = "eukrea,asoc-tlv320";
-		eukrea,model = "imx51-eukrea-tlv320aic23";
-		ssi-controller = <&ssi2>;
-		fsl,mux-int-port = <2>;
-		fsl,mux-ext-port = <3>;
-	};
-
-	usbphy1: usbphy1 {
-		compatible = "usb-nop-xceiv";
-		clocks = <&clks IMX5_CLK_USB_PHY_GATE>;
-		clock-names = "main_clk";
-		clock-frequency = <19200000>;
-		#phy-cells = <0>;
-	};
-};
-
-&audmux {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_audmux>;
-	status = "okay";
-};
-
-&esdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_esdhc1 &pinctrl_esdhc1_cd>;
-	cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-&ecspi1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi1>;
-	cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
-	status = "okay";
-
-	can0: can@0 {
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_can>;
-		compatible = "microchip,mcp2515";
-		reg = <0>;
-		clocks = <&clk24M>;
-		spi-max-frequency = <10000000>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
-		vdd-supply = <&reg_can>;
-	};
-};
-
-&i2c1 {
-	tlv320aic23: codec@1a {
-		compatible = "ti,tlv320aic23";
-		reg = <0x1a>;
-	};
-};
-
-&iomuxc {
-	imx51-eukrea {
-		pinctrl_audmux: audmuxgrp {
-			fsl,pins = <
-				MX51_PAD_AUD3_BB_TXD__AUD3_TXD		0x80000000
-				MX51_PAD_AUD3_BB_RXD__AUD3_RXD		0x80000000
-				MX51_PAD_AUD3_BB_CK__AUD3_TXC		0x80000000
-				MX51_PAD_AUD3_BB_FS__AUD3_TXFS		0x80000000
-			>;
-		};
-
-
-		pinctrl_can: cangrp {
-			fsl,pins = <
-				MX51_PAD_CSI2_PIXCLK__GPIO4_15		0x80000000	/* nReset */
-				MX51_PAD_GPIO1_1__GPIO1_1		0x80000000	/* IRQ */
-			>;
-		};
-
-		pinctrl_ecspi1: ecspi1grp {
-			fsl,pins = <
-				MX51_PAD_CSPI1_MISO__ECSPI1_MISO	0x185
-				MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI	0x185
-				MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK	0x185
-				MX51_PAD_CSPI1_SS0__GPIO4_24		0x80000000 	/* CS0 */
-			>;
-		};
-
-		pinctrl_esdhc1: esdhc1grp {
-			fsl,pins = <
-				MX51_PAD_SD1_CMD__SD1_CMD		0x400020d5
-				MX51_PAD_SD1_CLK__SD1_CLK		0x20d5
-				MX51_PAD_SD1_DATA0__SD1_DATA0		0x20d5
-				MX51_PAD_SD1_DATA1__SD1_DATA1		0x20d5
-				MX51_PAD_SD1_DATA2__SD1_DATA2		0x20d5
-				MX51_PAD_SD1_DATA3__SD1_DATA3		0x20d5
-			>;
-		};
-
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX51_PAD_UART1_RXD__UART1_RXD		0x1c5
-				MX51_PAD_UART1_TXD__UART1_TXD		0x1c5
-			>;
-		};
-
-		pinctrl_uart3: uart3grp {
-			fsl,pins = <
-				MX51_PAD_UART3_RXD__UART3_RXD		0x1c5
-				MX51_PAD_UART3_TXD__UART3_TXD		0x1c5
-			>;
-		};
-
-		pinctrl_uart3_rtscts: uart3rtsctsgrp {
-			fsl,pins = <
-				MX51_PAD_KEY_COL4__UART3_RTS		0x1c5
-				MX51_PAD_KEY_COL5__UART3_CTS		0x1c5
-			>;
-		};
-
-		pinctrl_backlight_1: backlightgrp-1 {
-			fsl,pins = <
-				MX51_PAD_DI1_D1_CS__GPIO3_4 0x1f5
-			>;
-		};
-
-		pinctrl_esdhc1_cd: esdhc1_cd {
-			fsl,pins = <
-				MX51_PAD_GPIO1_0__GPIO1_0 0xd5
-			>;
-		};
-
-		pinctrl_gpiokeys_1: gpiokeysgrp-1 {
-			fsl,pins = <
-				MX51_PAD_NANDF_D9__GPIO3_31 0x1f5
-			>;
-		};
-
-		pinctrl_gpioled: gpioledgrp-1 {
-			fsl,pins = <
-				MX51_PAD_NANDF_D10__GPIO3_30 0x80000000
-			>;
-		};
-
-		pinctrl_reg_lcd_3v3: reg_lcd_3v3 {
-			fsl,pins = <
-				MX51_PAD_CSI1_D9__GPIO3_13 0x1f5
-			>;
-		};
-
-		pinctrl_usbh1: usbh1grp {
-			fsl,pins = <
-				MX51_PAD_USBH1_CLK__USBH1_CLK     0x1e5
-				MX51_PAD_USBH1_DIR__USBH1_DIR     0x1e5
-				MX51_PAD_USBH1_NXT__USBH1_NXT     0x1e5
-				MX51_PAD_USBH1_DATA0__USBH1_DATA0 0x1e5
-				MX51_PAD_USBH1_DATA1__USBH1_DATA1 0x1e5
-				MX51_PAD_USBH1_DATA2__USBH1_DATA2 0x1e5
-				MX51_PAD_USBH1_DATA3__USBH1_DATA3 0x1e5
-				MX51_PAD_USBH1_DATA4__USBH1_DATA4 0x1e5
-				MX51_PAD_USBH1_DATA5__USBH1_DATA5 0x1e5
-				MX51_PAD_USBH1_DATA6__USBH1_DATA6 0x1e5
-				MX51_PAD_USBH1_DATA7__USBH1_DATA7 0x1e5
-				MX51_PAD_USBH1_STP__USBH1_STP     0x1e5
-			>;
-		};
-
-		pinctrl_usbh1_vbus: usbh1-vbusgrp {
-			fsl,pins = <
-				MX51_PAD_EIM_CS3__GPIO2_28 0x1f5
-			>;
-		};
-	};
-};
-
-&ssi2 {
-	codec-handle = <&tlv320aic23>;
-	status = "okay";
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
-	uart-has-rtscts;
-	status = "okay";
-};
-
-&uart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart3 &pinctrl_uart3_rtscts>;
-	uart-has-rtscts;
-	status = "okay";
-};
-
-&usbh1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbh1>;
-	fsl,usbphy = <&usbphy1>;
-	dr_mode = "host";
-	phy_type = "ulpi";
-	status = "okay";
-};
-
-&usbotg {
-	dr_mode = "otg";
-	phy_type = "utmi_wide";
-	status = "okay";
-};
-
-&usbphy0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbh1_vbus>;
-	reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
-};
diff --git a/arch/arm/boot/dts/imx53-ard.dts b/arch/arm/boot/dts/imx53-ard.dts
deleted file mode 100644
index 6208fbb2e741..000000000000
--- a/arch/arm/boot/dts/imx53-ard.dts
+++ /dev/null
@@ -1,179 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2011 Freescale Semiconductor, Inc.
- * Copyright 2011 Linaro Ltd.
- */
-
-/dts-v1/;
-#include <dt-bindings/input/input.h>
-#include "imx53.dtsi"
-
-/ {
-	model = "Freescale i.MX53 Automotive Reference Design Board";
-	compatible = "fsl,imx53-ard", "fsl,imx53";
-
-	memory@70000000 {
-		device_type = "memory";
-		reg = <0x70000000 0x40000000>;
-	};
-
-	eim-cs1@f4000000 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "fsl,eim-bus", "simple-bus";
-		reg = <0xf4000000 0x3ff0000>;
-		ranges;
-
-		ethernet@f4000000 {
-			compatible = "smsc,lan9220", "smsc,lan9115";
-			reg = <0xf4000000 0x2000000>;
-			phy-mode = "mii";
-			interrupt-parent = <&gpio2>;
-			interrupts = <31 0x8>;
-			reg-io-width = <4>;
-			/*
-			 * VDD33A and VDDVARIO of LAN9220 are supplied by
-			 * SW4_3V3 of LTC3589.  Before the regulator driver
-			 * for this PMIC is available, we use a fixed dummy
-			 * 3V3 regulator to get LAN9220 driver probing work.
-			 */
-			vdd33a-supply = <&reg_3p3v>;
-			vddvario-supply = <&reg_3p3v>;
-			smsc,irq-push-pull;
-		};
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		home {
-			label = "Home";
-			gpios = <&gpio5 10 0>;
-			linux,code = <KEY_HOME>;
-			wakeup-source;
-		};
-
-		back {
-			label = "Back";
-			gpios = <&gpio5 11 0>;
-			linux,code = <KEY_BACK>;
-			wakeup-source;
-		};
-
-		program {
-			label = "Program";
-			gpios = <&gpio5 12 0>;
-			linux,code = <KEY_PROGRAM >;
-			wakeup-source;
-		};
-
-		volume-up {
-			label = "Volume Up";
-			gpios = <&gpio5 13 0>;
-			linux,code = <KEY_VOLUMEUP>;
-		};
-
-		volume-down {
-			label = "Volume Down";
-			gpios = <&gpio4 0 0>;
-			linux,code = <KEY_VOLUMEDOWN>;
-		};
-	};
-};
-
-&esdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_esdhc1>;
-	cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
-	status = "okay";
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_hog>;
-
-	imx53-ard {
-		pinctrl_hog: hoggrp {
-			fsl,pins = <
-				MX53_PAD_GPIO_1__GPIO1_1             0x80000000
-				MX53_PAD_GPIO_9__GPIO1_9             0x80000000
-				MX53_PAD_EIM_EB3__GPIO2_31           0x80000000
-				MX53_PAD_GPIO_10__GPIO4_0            0x80000000
-				MX53_PAD_DISP0_DAT16__GPIO5_10	     0x80000000
-				MX53_PAD_DISP0_DAT17__GPIO5_11       0x80000000
-				MX53_PAD_DISP0_DAT18__GPIO5_12       0x80000000
-				MX53_PAD_DISP0_DAT19__GPIO5_13       0x80000000
-				MX53_PAD_EIM_D16__EMI_WEIM_D_16      0x80000000
-				MX53_PAD_EIM_D17__EMI_WEIM_D_17      0x80000000
-				MX53_PAD_EIM_D18__EMI_WEIM_D_18      0x80000000
-				MX53_PAD_EIM_D19__EMI_WEIM_D_19      0x80000000
-				MX53_PAD_EIM_D20__EMI_WEIM_D_20      0x80000000
-				MX53_PAD_EIM_D21__EMI_WEIM_D_21      0x80000000
-				MX53_PAD_EIM_D22__EMI_WEIM_D_22      0x80000000
-				MX53_PAD_EIM_D23__EMI_WEIM_D_23      0x80000000
-				MX53_PAD_EIM_D24__EMI_WEIM_D_24      0x80000000
-				MX53_PAD_EIM_D25__EMI_WEIM_D_25      0x80000000
-				MX53_PAD_EIM_D26__EMI_WEIM_D_26      0x80000000
-				MX53_PAD_EIM_D27__EMI_WEIM_D_27      0x80000000
-				MX53_PAD_EIM_D28__EMI_WEIM_D_28      0x80000000
-				MX53_PAD_EIM_D29__EMI_WEIM_D_29      0x80000000
-				MX53_PAD_EIM_D30__EMI_WEIM_D_30      0x80000000
-				MX53_PAD_EIM_D31__EMI_WEIM_D_31      0x80000000
-				MX53_PAD_EIM_DA0__EMI_NAND_WEIM_DA_0 0x80000000
-				MX53_PAD_EIM_DA1__EMI_NAND_WEIM_DA_1 0x80000000
-				MX53_PAD_EIM_DA2__EMI_NAND_WEIM_DA_2 0x80000000
-				MX53_PAD_EIM_DA3__EMI_NAND_WEIM_DA_3 0x80000000
-				MX53_PAD_EIM_DA4__EMI_NAND_WEIM_DA_4 0x80000000
-				MX53_PAD_EIM_DA5__EMI_NAND_WEIM_DA_5 0x80000000
-				MX53_PAD_EIM_DA6__EMI_NAND_WEIM_DA_6 0x80000000
-				MX53_PAD_EIM_OE__EMI_WEIM_OE	     0x80000000
-				MX53_PAD_EIM_RW__EMI_WEIM_RW	     0x80000000
-				MX53_PAD_EIM_CS1__EMI_WEIM_CS_1	     0x80000000
-			>;
-		};
-
-		pinctrl_esdhc1: esdhc1grp {
-			fsl,pins = <
-				MX53_PAD_SD1_DATA0__ESDHC1_DAT0		0x1d5
-				MX53_PAD_SD1_DATA1__ESDHC1_DAT1		0x1d5
-				MX53_PAD_SD1_DATA2__ESDHC1_DAT2		0x1d5
-				MX53_PAD_SD1_DATA3__ESDHC1_DAT3		0x1d5
-				MX53_PAD_PATA_DATA8__ESDHC1_DAT4	0x1d5
-				MX53_PAD_PATA_DATA9__ESDHC1_DAT5	0x1d5
-				MX53_PAD_PATA_DATA10__ESDHC1_DAT6	0x1d5
-				MX53_PAD_PATA_DATA11__ESDHC1_DAT7	0x1d5
-				MX53_PAD_SD1_CMD__ESDHC1_CMD		0x1d5
-				MX53_PAD_SD1_CLK__ESDHC1_CLK		0x1d5
-			>;
-		};
-
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX53_PAD_PATA_DIOW__UART1_TXD_MUX	0x1e4
-				MX53_PAD_PATA_DMACK__UART1_RXD_MUX	0x1e4
-			>;
-		};
-	};
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx53-m53.dtsi b/arch/arm/boot/dts/imx53-m53.dtsi
deleted file mode 100644
index fe5e0d308e99..000000000000
--- a/arch/arm/boot/dts/imx53-m53.dtsi
+++ /dev/null
@@ -1,132 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2014 Marek Vasut <marex@denx.de>
- */
-
-#include "imx53.dtsi"
-
-/ {
-	model = "Aries/DENX M53";
-	compatible = "aries,imx53-m53", "denx,imx53-m53", "fsl,imx53";
-
-	memory@70000000 {
-		device_type = "memory";
-		reg = <0x70000000 0x20000000>,
-		      <0xb0000000 0x20000000>;
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p2v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P2V";
-			regulator-min-microvolt = <3200000>;
-			regulator-max-microvolt = <3200000>;
-			regulator-always-on;
-		};
-
-		reg_backlight: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "lcd-supply";
-			regulator-min-microvolt = <3200000>;
-			regulator-max-microvolt = <3200000>;
-			regulator-always-on;
-		};
-	};
-};
-
-&i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c2>;
-	clock-frequency = <400000>;
-	status = "okay";
-
-	touchscreen@41 {
-		compatible = "st,stmpe610";
-		reg = <0x41>;
-		id = <0>;
-		blocks = <0x5>;
-		interrupts = <6 0x0>;
-		interrupt-parent = <&gpio7>;
-		irq-trigger = <0x1>;
-
-		stmpe_touchscreen {
-			compatible = "st,stmpe-ts";
-			st,sample-time = <4>;
-			st,mod-12b = <1>;
-			st,ref-sel = <0>;
-			st,adc-freq = <1>;
-			st,ave-ctrl = <3>;
-			st,touch-det-delay = <3>;
-			st,settling = <4>;
-			st,fraction-z = <7>;
-			st,i-drive = <1>;
-		};
-	};
-
-	eeprom: eeprom@50 {
-		compatible = "atmel,24c128";
-		reg = <0x50>;
-		pagesize = <32>;
-	};
-
-	rtc: rtc@68 {
-		compatible = "st,m41t62";
-		reg = <0x68>;
-	};
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_hog>;
-
-	imx53-m53evk {
-		pinctrl_hog: hoggrp {
-			fsl,pins = <
-				MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK	0x80000000
-				MX53_PAD_EIM_EB3__GPIO2_31		0x80000000
-				MX53_PAD_PATA_DA_0__GPIO7_6		0x80000000
-			>;
-		};
-
-		pinctrl_i2c2: i2c2grp {
-			fsl,pins = <
-				MX53_PAD_EIM_D16__I2C2_SDA		0xc0000000
-				MX53_PAD_EIM_EB2__I2C2_SCL		0xc0000000
-			>;
-		};
-
-		pinctrl_nand: nandgrp {
-			fsl,pins = <
-				MX53_PAD_NANDF_WE_B__EMI_NANDF_WE_B	0x4
-				MX53_PAD_NANDF_RE_B__EMI_NANDF_RE_B	0x4
-				MX53_PAD_NANDF_CLE__EMI_NANDF_CLE	0x4
-				MX53_PAD_NANDF_ALE__EMI_NANDF_ALE	0x4
-				MX53_PAD_NANDF_WP_B__EMI_NANDF_WP_B	0xe0
-				MX53_PAD_NANDF_RB0__EMI_NANDF_RB_0	0xe0
-				MX53_PAD_NANDF_CS0__EMI_NANDF_CS_0	0x4
-				MX53_PAD_PATA_DATA0__EMI_NANDF_D_0	0xa4
-				MX53_PAD_PATA_DATA1__EMI_NANDF_D_1	0xa4
-				MX53_PAD_PATA_DATA2__EMI_NANDF_D_2	0xa4
-				MX53_PAD_PATA_DATA3__EMI_NANDF_D_3	0xa4
-				MX53_PAD_PATA_DATA4__EMI_NANDF_D_4	0xa4
-				MX53_PAD_PATA_DATA5__EMI_NANDF_D_5	0xa4
-				MX53_PAD_PATA_DATA6__EMI_NANDF_D_6	0xa4
-				MX53_PAD_PATA_DATA7__EMI_NANDF_D_7	0xa4
-			>;
-		};
-	};
-};
-
-&nfc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_nand>;
-	nand-bus-width = <8>;
-	nand-ecc-mode = "hw";
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx53-m53evk.dts b/arch/arm/boot/dts/imx53-m53evk.dts
deleted file mode 100644
index a1a6228d1aa6..000000000000
--- a/arch/arm/boot/dts/imx53-m53evk.dts
+++ /dev/null
@@ -1,371 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright (C) 2013 Marek Vasut <marex@denx.de>
- */
-
-/dts-v1/;
-#include "imx53-m53.dtsi"
-
-/ {
-	model = "Aries/DENX M53EVK";
-	compatible = "aries,imx53-m53evk", "denx,imx53-m53evk", "fsl,imx53";
-
-	display1: disp1 {
-		compatible = "fsl,imx-parallel-display";
-		interface-pix-fmt = "bgr666";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_ipu_disp1>;
-
-		display-timings {
-			800x480p60 {
-				native-mode;
-				clock-frequency = <31500000>;
-				hactive = <800>;
-				vactive = <480>;
-				hfront-porch = <40>;
-				hback-porch = <88>;
-				hsync-len = <128>;
-				vback-porch = <33>;
-				vfront-porch = <9>;
-				vsync-len = <3>;
-				vsync-active = <1>;
-			};
-		};
-
-		port {
-			display1_in: endpoint {
-				remote-endpoint = <&ipu_di1_disp1>;
-			};
-		};
-	};
-
-	backlight {
-		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 3000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <6>;
-		power-supply = <&reg_backlight>;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pin_gpio>;
-
-		user1 {
-			label = "user1";
-			gpios = <&gpio2 8 0>;
-			linux,default-trigger = "heartbeat";
-		};
-
-		user2 {
-			label = "user2";
-			gpios = <&gpio2 9 0>;
-			linux,default-trigger = "heartbeat";
-		};
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_usbh1_vbus: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio1 2 0>;
-		};
-
-		reg_usb_otg_vbus: regulator@4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio1 4 0>;
-		};
-	};
-
-	sound {
-		compatible = "fsl,imx53-m53evk-sgtl5000",
-			     "fsl,imx-audio-sgtl5000";
-		model = "imx53-m53evk-sgtl5000";
-		ssi-controller = <&ssi2>;
-		audio-codec = <&sgtl5000>;
-		audio-routing =
-			"MIC_IN", "Mic Jack",
-			"Mic Jack", "Mic Bias",
-			"LINE_IN", "Line In Jack",
-			"Headphone Jack", "HP_OUT",
-			"Ext Spk", "LINE_OUT";
-		mux-int-port = <2>;
-		mux-ext-port = <4>;
-	};
-};
-
-&audmux {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_audmux>;
-	status = "okay";
-};
-
-&can1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_can1>;
-	status = "okay";
-};
-
-&can2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_can2>;
-	status = "okay";
-};
-
-&esdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_esdhc1>;
-	cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
-	status = "okay";
-};
-
-&fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_fec>;
-	phy-mode = "rmii";
-	status = "okay";
-};
-
-&i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c1>;
-	status = "okay";
-
-	sgtl5000: codec@a {
-		compatible = "fsl,sgtl5000";
-		reg = <0x0a>;
-		#sound-dai-cells = <0>;
-		VDDA-supply = <&reg_3p2v>;
-		VDDIO-supply = <&reg_3p2v>;
-		clocks = <&clks IMX5_CLK_SSI_EXT1_GATE>;
-	};
-};
-
-&i2c3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c3>;
-	status = "okay";
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_hog>;
-
-	imx53-m53evk {
-		pinctrl_usb: usbgrp {
-			fsl,pins = <
-				MX53_PAD_GPIO_2__GPIO1_2		0x80000000
-				MX53_PAD_GPIO_3__USBOH3_USBH1_OC	0x80000000
-			>;
-		};
-
-		pinctrl_usbotg: usbotggrp {
-			fsl,pins = <
-				MX53_PAD_GPIO_4__GPIO1_4		0x000b0
-			>;
-		};
-
-		led_pin_gpio: led_gpio {
-			fsl,pins = <
-				MX53_PAD_PATA_DATA8__GPIO2_8		0x80000000
-				MX53_PAD_PATA_DATA9__GPIO2_9		0x80000000
-			>;
-		};
-
-		pinctrl_audmux: audmuxgrp {
-			fsl,pins = <
-				MX53_PAD_SD2_DATA3__AUDMUX_AUD4_TXC	0x80000000
-				MX53_PAD_SD2_DATA2__AUDMUX_AUD4_TXD	0x80000000
-				MX53_PAD_SD2_DATA1__AUDMUX_AUD4_TXFS	0x80000000
-				MX53_PAD_SD2_DATA0__AUDMUX_AUD4_RXD	0x80000000
-			>;
-		};
-
-		pinctrl_can1: can1grp {
-			fsl,pins = <
-				MX53_PAD_GPIO_7__CAN1_TXCAN		0x80000000
-				MX53_PAD_GPIO_8__CAN1_RXCAN		0x80000000
-			>;
-		};
-
-		pinctrl_can2: can2grp {
-			fsl,pins = <
-				MX53_PAD_KEY_COL4__CAN2_TXCAN		0x80000000
-				MX53_PAD_KEY_ROW4__CAN2_RXCAN		0x80000000
-			>;
-		};
-
-		pinctrl_esdhc1: esdhc1grp {
-			fsl,pins = <
-				MX53_PAD_SD1_DATA0__ESDHC1_DAT0		0x1d5
-				MX53_PAD_SD1_DATA1__ESDHC1_DAT1		0x1d5
-				MX53_PAD_SD1_DATA2__ESDHC1_DAT2		0x1d5
-				MX53_PAD_SD1_DATA3__ESDHC1_DAT3		0x1d5
-				MX53_PAD_SD1_CMD__ESDHC1_CMD		0x1d5
-				MX53_PAD_SD1_CLK__ESDHC1_CLK		0x1d5
-			>;
-		};
-
-		pinctrl_fec: fecgrp {
-			fsl,pins = <
-				MX53_PAD_FEC_MDC__FEC_MDC		0x80000000
-				MX53_PAD_FEC_MDIO__FEC_MDIO		0x80000000
-				MX53_PAD_FEC_REF_CLK__FEC_TX_CLK	0x80000000
-				MX53_PAD_FEC_RX_ER__FEC_RX_ER		0x80000000
-				MX53_PAD_FEC_CRS_DV__FEC_RX_DV		0x80000000
-				MX53_PAD_FEC_RXD1__FEC_RDATA_1		0x80000000
-				MX53_PAD_FEC_RXD0__FEC_RDATA_0		0x80000000
-				MX53_PAD_FEC_TX_EN__FEC_TX_EN		0x80000000
-				MX53_PAD_FEC_TXD1__FEC_TDATA_1		0x80000000
-				MX53_PAD_FEC_TXD0__FEC_TDATA_0		0x80000000
-			>;
-		};
-
-		pinctrl_i2c1: i2c1grp {
-			fsl,pins = <
-				MX53_PAD_EIM_D21__I2C1_SCL		0xc0000000
-				MX53_PAD_EIM_D28__I2C1_SDA		0xc0000000
-			>;
-		};
-
-		pinctrl_i2c3: i2c3grp {
-			fsl,pins = <
-				MX53_PAD_GPIO_6__I2C3_SDA		0xc0000000
-				MX53_PAD_GPIO_5__I2C3_SCL		0xc0000000
-			>;
-		};
-
-		pinctrl_ipu_disp1: ipudisp1grp {
-			fsl,pins = <
-				MX53_PAD_EIM_DA9__IPU_DISP1_DAT_0	0x5
-				MX53_PAD_EIM_DA8__IPU_DISP1_DAT_1	0x5
-				MX53_PAD_EIM_DA7__IPU_DISP1_DAT_2	0x5
-				MX53_PAD_EIM_DA6__IPU_DISP1_DAT_3	0x5
-				MX53_PAD_EIM_DA5__IPU_DISP1_DAT_4	0x5
-				MX53_PAD_EIM_DA4__IPU_DISP1_DAT_5	0x5
-				MX53_PAD_EIM_DA3__IPU_DISP1_DAT_6	0x5
-				MX53_PAD_EIM_DA2__IPU_DISP1_DAT_7	0x5
-				MX53_PAD_EIM_DA1__IPU_DISP1_DAT_8	0x5
-				MX53_PAD_EIM_DA0__IPU_DISP1_DAT_9	0x5
-				MX53_PAD_EIM_EB1__IPU_DISP1_DAT_10	0x5
-				MX53_PAD_EIM_EB0__IPU_DISP1_DAT_11	0x5
-				MX53_PAD_EIM_A17__IPU_DISP1_DAT_12	0x5
-				MX53_PAD_EIM_A18__IPU_DISP1_DAT_13	0x5
-				MX53_PAD_EIM_A19__IPU_DISP1_DAT_14	0x5
-				MX53_PAD_EIM_A20__IPU_DISP1_DAT_15	0x5
-				MX53_PAD_EIM_A21__IPU_DISP1_DAT_16	0x5
-				MX53_PAD_EIM_A22__IPU_DISP1_DAT_17	0x5
-				MX53_PAD_EIM_A23__IPU_DISP1_DAT_18	0x5
-				MX53_PAD_EIM_A24__IPU_DISP1_DAT_19	0x5
-				MX53_PAD_EIM_D31__IPU_DISP1_DAT_20	0x5
-				MX53_PAD_EIM_D30__IPU_DISP1_DAT_21	0x5
-				MX53_PAD_EIM_D26__IPU_DISP1_DAT_22	0x5
-				MX53_PAD_EIM_D27__IPU_DISP1_DAT_23	0x5
-				MX53_PAD_EIM_A16__IPU_DI1_DISP_CLK	0x5
-				MX53_PAD_EIM_DA13__IPU_DI1_D0_CS	0x5
-				MX53_PAD_EIM_DA14__IPU_DI1_D1_CS	0x5
-				MX53_PAD_EIM_DA15__IPU_DI1_PIN1		0x5
-				MX53_PAD_EIM_DA11__IPU_DI1_PIN2		0x5
-				MX53_PAD_EIM_DA12__IPU_DI1_PIN3		0x5
-				MX53_PAD_EIM_A25__IPU_DI1_PIN12		0x5
-				MX53_PAD_EIM_DA10__IPU_DI1_PIN15	0x5
-			>;
-		};
-
-		pinctrl_pwm1: pwm1grp {
-			fsl,pins = <
-				MX53_PAD_DISP0_DAT8__PWM1_PWMO		0x5
-			>;
-		};
-
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX53_PAD_PATA_DIOW__UART1_TXD_MUX	0x1e4
-				MX53_PAD_PATA_DMACK__UART1_RXD_MUX	0x1e4
-			>;
-		};
-
-		pinctrl_uart2: uart2grp {
-			fsl,pins = <
-				MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX	0x1e4
-				MX53_PAD_PATA_DMARQ__UART2_TXD_MUX	0x1e4
-			>;
-		};
-
-		pinctrl_uart3: uart3grp {
-			fsl,pins = <
-				MX53_PAD_PATA_CS_0__UART3_TXD_MUX	0x1e4
-				MX53_PAD_PATA_CS_1__UART3_RXD_MUX	0x1e4
-				MX53_PAD_PATA_DA_1__UART3_CTS		0x1e4
-				MX53_PAD_PATA_DA_2__UART3_RTS		0x1e4
-			>;
-		};
-	};
-};
-
-&ipu_di1_disp1 {
-	remote-endpoint = <&display1_in>;
-};
-
-&pwm1 {
-	#pwm-cells = <2>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm1>;
-	status = "okay";
-};
-
-&sata {
-	status = "okay";
-};
-
-&ssi2 {
-	status = "okay";
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
-	status = "okay";
-};
-
-&uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
-	status = "okay";
-};
-
-&uart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart3>;
-	status = "okay";
-};
-
-&usbh1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usb>;
-	vbus-supply = <&reg_usbh1_vbus>;
-	phy_type = "utmi";
-	status = "okay";
-};
-
-&usbotg {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbotg>;
-	dr_mode = "otg";
-	vbus-supply = <&reg_usb_otg_vbus>;
-	disable-over-current;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx53-mba53.dts b/arch/arm/boot/dts/imx53-mba53.dts
deleted file mode 100644
index 09eee0dd44c1..000000000000
--- a/arch/arm/boot/dts/imx53-mba53.dts
+++ /dev/null
@@ -1,249 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2012 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
- * Copyright 2012 Steffen Trumtrar <s.trumtrar@pengutronix.de>, Pengutronix
- */
-
-/dts-v1/;
-#include "imx53-tqma53.dtsi"
-
-/ {
-	model = "TQ MBa53 starter kit";
-	compatible = "tq,mba53", "tq,tqma53", "fsl,imx53";
-
-	chosen {
-		stdout-path = &uart2;
-	};
-
-	backlight {
-		compatible = "pwm-backlight";
-		pwms = <&pwm2 0 50000>;
-		brightness-levels = <0 24 28 32 36 40 44 48 52 56 60 64 68 72 76 80 84 88 92 96 100>;
-		default-brightness-level = <10>;
-		enable-gpios = <&gpio7 7 0>;
-		power-supply = <&reg_backlight>;
-	};
-
-	disp1: disp1 {
-		compatible = "fsl,imx-parallel-display";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_disp1_1>;
-		interface-pix-fmt = "rgb24";
-		status = "disabled";
-
-		port {
-			display1_in: endpoint {
-				remote-endpoint = <&ipu_di1_disp1>;
-			};
-		};
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_backlight: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "lcd-supply";
-			gpio = <&gpio2 5 0>;
-			startup-delay-us = <5000>;
-		};
-
-		reg_3p2v: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "3P2V";
-			regulator-min-microvolt = <3200000>;
-			regulator-max-microvolt = <3200000>;
-			regulator-always-on;
-		};
-	};
-
-	sound {
-		compatible = "tq,imx53-mba53-sgtl5000",
-			     "fsl,imx-audio-sgtl5000";
-		model = "imx53-mba53-sgtl5000";
-		ssi-controller = <&ssi2>;
-		audio-codec = <&codec>;
-		audio-routing =
-			"MIC_IN", "Mic Jack",
-			"Mic Jack", "Mic Bias",
-			"Headphone Jack", "HP_OUT";
-		mux-int-port = <2>;
-		mux-ext-port = <5>;
-	};
-};
-
-&ldb {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_lvds1_1>;
-	status = "disabled";
-};
-
-&iomuxc {
-	lvds1 {
-		pinctrl_lvds1_1: lvds1-grp1 {
-			fsl,pins = <
-				MX53_PAD_LVDS0_TX3_P__LDB_LVDS0_TX3 0x80000000
-				MX53_PAD_LVDS0_CLK_P__LDB_LVDS0_CLK 0x80000000
-				MX53_PAD_LVDS0_TX2_P__LDB_LVDS0_TX2 0x80000000
-				MX53_PAD_LVDS0_TX1_P__LDB_LVDS0_TX1 0x80000000
-				MX53_PAD_LVDS0_TX0_P__LDB_LVDS0_TX0 0x80000000
-			>;
-		};
-
-		pinctrl_lvds1_2: lvds1-grp2 {
-			fsl,pins = <
-				MX53_PAD_LVDS1_TX3_P__LDB_LVDS1_TX3 0x80000000
-				MX53_PAD_LVDS1_TX2_P__LDB_LVDS1_TX2 0x80000000
-				MX53_PAD_LVDS1_CLK_P__LDB_LVDS1_CLK 0x80000000
-				MX53_PAD_LVDS1_TX1_P__LDB_LVDS1_TX1 0x80000000
-				MX53_PAD_LVDS1_TX0_P__LDB_LVDS1_TX0 0x80000000
-			>;
-		};
-	};
-
-	disp1 {
-		pinctrl_disp1_1: disp1-grp1 {
-			fsl,pins = <
-				MX53_PAD_EIM_A16__IPU_DI1_DISP_CLK 0x80000000 /* DISP1_CLK */
-				MX53_PAD_EIM_DA10__IPU_DI1_PIN15   0x80000000 /* DISP1_DRDY */
-				MX53_PAD_EIM_D23__IPU_DI1_PIN2     0x80000000 /* DISP1_HSYNC */
-				MX53_PAD_EIM_EB3__IPU_DI1_PIN3     0x80000000 /* DISP1_VSYNC */
-				MX53_PAD_EIM_D26__IPU_DISP1_DAT_22 0x80000000
-				MX53_PAD_EIM_D27__IPU_DISP1_DAT_23 0x80000000
-				MX53_PAD_EIM_D30__IPU_DISP1_DAT_21 0x80000000
-				MX53_PAD_EIM_D31__IPU_DISP1_DAT_20 0x80000000
-				MX53_PAD_EIM_A24__IPU_DISP1_DAT_19 0x80000000
-				MX53_PAD_EIM_A23__IPU_DISP1_DAT_18 0x80000000
-				MX53_PAD_EIM_A22__IPU_DISP1_DAT_17 0x80000000
-				MX53_PAD_EIM_A21__IPU_DISP1_DAT_16 0x80000000
-				MX53_PAD_EIM_A20__IPU_DISP1_DAT_15 0x80000000
-				MX53_PAD_EIM_A19__IPU_DISP1_DAT_14 0x80000000
-				MX53_PAD_EIM_A18__IPU_DISP1_DAT_13 0x80000000
-				MX53_PAD_EIM_A17__IPU_DISP1_DAT_12 0x80000000
-				MX53_PAD_EIM_EB0__IPU_DISP1_DAT_11 0x80000000
-				MX53_PAD_EIM_EB1__IPU_DISP1_DAT_10 0x80000000
-				MX53_PAD_EIM_DA0__IPU_DISP1_DAT_9  0x80000000
-				MX53_PAD_EIM_DA1__IPU_DISP1_DAT_8  0x80000000
-				MX53_PAD_EIM_DA2__IPU_DISP1_DAT_7  0x80000000
-				MX53_PAD_EIM_DA3__IPU_DISP1_DAT_6  0x80000000
-				MX53_PAD_EIM_DA4__IPU_DISP1_DAT_5  0x80000000
-				MX53_PAD_EIM_DA5__IPU_DISP1_DAT_4  0x80000000
-				MX53_PAD_EIM_DA6__IPU_DISP1_DAT_3  0x80000000
-				MX53_PAD_EIM_DA7__IPU_DISP1_DAT_2  0x80000000
-				MX53_PAD_EIM_DA8__IPU_DISP1_DAT_1  0x80000000
-				MX53_PAD_EIM_DA9__IPU_DISP1_DAT_0  0x80000000
-			>;
-		};
-	};
-
-	tve {
-		pinctrl_vga_sync_1: vgasync-grp1 {
-			fsl,pins = <
-				/* VGA_VSYNC, HSYNC with max drive strength */
-				MX53_PAD_EIM_CS1__IPU_DI1_PIN6	   0xe6
-				MX53_PAD_EIM_DA15__IPU_DI1_PIN4	   0xe6
-			>;
-		};
-	};
-};
-
-&ipu_di1_disp1 {
-	remote-endpoint = <&display1_in>;
-};
-
-&cspi {
-	status = "okay";
-};
-
-&audmux {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_audmux>;
-};
-
-&i2c2 {
-	codec: sgtl5000@a {
-		compatible = "fsl,sgtl5000";
-		reg = <0x0a>;
-		clocks = <&clks IMX5_CLK_SSI_EXT1_GATE>;
-		VDDA-supply = <&reg_3p2v>;
-		VDDIO-supply = <&reg_3p2v>;
-	};
-
-	expander: pca9554@20 {
-		compatible = "pca9554";
-		reg = <0x20>;
-		interrupts = <109>;
-		#gpio-cells = <2>;
-		gpio-controller;
-	};
-
-	sensor2: lm75@49 {
-		compatible = "lm75";
-		reg = <0x49>;
-	};
-};
-
-&fec {
-	phy-reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-&esdhc2 {
-	status = "okay";
-};
-
-&uart3 {
-	status = "okay";
-};
-
-&ecspi1 {
-	status = "okay";
-};
-
-&usbotg {
-	dr_mode = "host";
-	status = "okay";
-};
-
-&usbh1 {
-	status = "okay";
-};
-
-&uart1 {
-	status = "okay";
-};
-
-&ssi2 {
-	status = "okay";
-};
-
-&uart2 {
-	status = "okay";
-};
-
-&can1 {
-	status = "okay";
-};
-
-&can2 {
-	status = "okay";
-};
-
-&i2c3 {
-	status = "okay";
-};
-
-&tve {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_vga_sync_1>;
-	ddc-i2c-bus = <&i2c3>;
-	fsl,tve-mode = "vga";
-	fsl,hsync-pin = <4>;
-	fsl,vsync-pin = <6>;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx53-qsb-common.dtsi b/arch/arm/boot/dts/imx53-qsb-common.dtsi
deleted file mode 100644
index fe4244044a0f..000000000000
--- a/arch/arm/boot/dts/imx53-qsb-common.dtsi
+++ /dev/null
@@ -1,387 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-//
-// Copyright 2011 Freescale Semiconductor, Inc.
-// Copyright 2011 Linaro Ltd.
-
-#include "imx53.dtsi"
-
-/ {
-	chosen {
-		stdout-path = &uart1;
-	};
-
-	memory@70000000 {
-		device_type = "memory";
-		reg = <0x70000000 0x20000000>,
-		      <0xb0000000 0x20000000>;
-	};
-
-	display0: disp0 {
-		compatible = "fsl,imx-parallel-display";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_ipu_disp0>;
-
-		#address-cells = <1>;
-		#size-cells = <0>;
-		status = "disabled";
-
-		port@0 {
-			reg = <0>;
-
-			display0_in: endpoint {
-				remote-endpoint = <&ipu_di0_disp0>;
-			};
-		};
-
-		port@1 {
-			reg = <1>;
-
-			display_out: endpoint {
-				remote-endpoint = <&panel_in>;
-			};
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		power {
-			label = "Power Button";
-			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_POWER>;
-		};
-
-		volume-up {
-			label = "Volume Up";
-			gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEUP>;
-			wakeup-source;
-		};
-
-		volume-down {
-			label = "Volume Down";
-			gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEDOWN>;
-			wakeup-source;
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pin_gpio7_7>;
-
-		user {
-			label = "Heartbeat";
-			gpios = <&gpio7 7 0>;
-			linux,default-trigger = "heartbeat";
-		};
-	};
-
-	panel {
-		compatible = "sii,43wvf1g";
-
-		port {
-			panel_in: endpoint {
-				remote-endpoint = <&display_out>;
-			};
-		};
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p2v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P2V";
-			regulator-min-microvolt = <3200000>;
-			regulator-max-microvolt = <3200000>;
-			regulator-always-on;
-		};
-
-		reg_usb_vbus: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "usb_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio7 8 0>;
-			enable-active-high;
-		};
-	};
-
-	sound {
-		compatible = "fsl,imx53-qsb-sgtl5000",
-			     "fsl,imx-audio-sgtl5000";
-		model = "imx53-qsb-sgtl5000";
-		ssi-controller = <&ssi2>;
-		audio-codec = <&sgtl5000>;
-		audio-routing =
-			"MIC_IN", "Mic Jack",
-			"Mic Jack", "Mic Bias",
-			"Headphone Jack", "HP_OUT";
-		mux-int-port = <2>;
-		mux-ext-port = <5>;
-	};
-};
-
-&cpu0 {
-	/* CPU rated to 1GHz, not 1.2GHz as per the default settings */
-	operating-points = <
-		/* kHz   uV */
-		166666  850000
-		400000  900000
-		800000  1050000
-		1000000 1200000
-	>;
-};
-
-&esdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_esdhc1>;
-	cd-gpios = <&gpio3 13 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-&ipu_di0_disp0 {
-	remote-endpoint = <&display0_in>;
-};
-
-&ssi2 {
-	status = "okay";
-};
-
-&esdhc3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_esdhc3>;
-	cd-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio3 12 GPIO_ACTIVE_HIGH>;
-	bus-width = <8>;
-	status = "okay";
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_hog>;
-
-	imx53-qsb {
-		pinctrl_hog: hoggrp {
-			fsl,pins = <
-				MX53_PAD_GPIO_8__GPIO1_8          0x80000000
-				MX53_PAD_PATA_DATA14__GPIO2_14    0x80000000
-				MX53_PAD_PATA_DATA15__GPIO2_15    0x80000000
-				MX53_PAD_EIM_DA11__GPIO3_11       0x80000000
-				MX53_PAD_EIM_DA12__GPIO3_12       0x80000000
-				MX53_PAD_PATA_DA_0__GPIO7_6       0x80000000
-				MX53_PAD_PATA_DA_2__GPIO7_8	  0x80000000
-				MX53_PAD_GPIO_16__GPIO7_11        0x80000000
-			>;
-		};
-
-		led_pin_gpio7_7: led_gpio7_7 {
-			fsl,pins = <
-				MX53_PAD_PATA_DA_1__GPIO7_7 0x80000000
-			>;
-		};
-
-		pinctrl_audmux: audmuxgrp {
-			fsl,pins = <
-				MX53_PAD_KEY_COL0__AUDMUX_AUD5_TXC	0x80000000
-				MX53_PAD_KEY_ROW0__AUDMUX_AUD5_TXD	0x80000000
-				MX53_PAD_KEY_COL1__AUDMUX_AUD5_TXFS	0x80000000
-				MX53_PAD_KEY_ROW1__AUDMUX_AUD5_RXD	0x80000000
-			>;
-		};
-
-		pinctrl_codec: codecgrp {
-			fsl,pins = <
-				MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK	0x1c4
-			>;
-		};
-
-		pinctrl_esdhc1: esdhc1grp {
-			fsl,pins = <
-				MX53_PAD_SD1_DATA0__ESDHC1_DAT0		0x1d5
-				MX53_PAD_SD1_DATA1__ESDHC1_DAT1		0x1d5
-				MX53_PAD_SD1_DATA2__ESDHC1_DAT2		0x1d5
-				MX53_PAD_SD1_DATA3__ESDHC1_DAT3		0x1d5
-				MX53_PAD_SD1_CMD__ESDHC1_CMD		0x1d5
-				MX53_PAD_SD1_CLK__ESDHC1_CLK		0x1d5
-				MX53_PAD_EIM_DA13__GPIO3_13		0xe4
-			>;
-		};
-
-		pinctrl_esdhc3: esdhc3grp {
-			fsl,pins = <
-				MX53_PAD_PATA_DATA8__ESDHC3_DAT0	0x1d5
-				MX53_PAD_PATA_DATA9__ESDHC3_DAT1	0x1d5
-				MX53_PAD_PATA_DATA10__ESDHC3_DAT2	0x1d5
-				MX53_PAD_PATA_DATA11__ESDHC3_DAT3	0x1d5
-				MX53_PAD_PATA_DATA0__ESDHC3_DAT4	0x1d5
-				MX53_PAD_PATA_DATA1__ESDHC3_DAT5	0x1d5
-				MX53_PAD_PATA_DATA2__ESDHC3_DAT6	0x1d5
-				MX53_PAD_PATA_DATA3__ESDHC3_DAT7	0x1d5
-				MX53_PAD_PATA_RESET_B__ESDHC3_CMD	0x1d5
-				MX53_PAD_PATA_IORDY__ESDHC3_CLK		0x1d5
-			>;
-		};
-
-		pinctrl_fec: fecgrp {
-			fsl,pins = <
-				MX53_PAD_FEC_MDC__FEC_MDC		0x4
-				MX53_PAD_FEC_MDIO__FEC_MDIO		0x1fc
-				MX53_PAD_FEC_REF_CLK__FEC_TX_CLK	0x180
-				MX53_PAD_FEC_RX_ER__FEC_RX_ER		0x180
-				MX53_PAD_FEC_CRS_DV__FEC_RX_DV		0x180
-				MX53_PAD_FEC_RXD1__FEC_RDATA_1		0x180
-				MX53_PAD_FEC_RXD0__FEC_RDATA_0		0x180
-				MX53_PAD_FEC_TX_EN__FEC_TX_EN		0x4
-				MX53_PAD_FEC_TXD1__FEC_TDATA_1		0x4
-				MX53_PAD_FEC_TXD0__FEC_TDATA_0		0x4
-			>;
-		};
-
-		/* open drain */
-		pinctrl_i2c1: i2c1grp {
-			fsl,pins = <
-				MX53_PAD_CSI0_DAT8__I2C1_SDA		0x400001ec
-				MX53_PAD_CSI0_DAT9__I2C1_SCL		0x400001ec
-			>;
-		};
-
-		pinctrl_i2c2: i2c2grp {
-			fsl,pins = <
-				MX53_PAD_KEY_ROW3__I2C2_SDA		0xc0000000
-				MX53_PAD_KEY_COL3__I2C2_SCL		0xc0000000
-			>;
-		};
-
-		pinctrl_ipu_disp0: ipudisp0grp {
-			fsl,pins = <
-				MX53_PAD_DI0_DISP_CLK__IPU_DI0_DISP_CLK	0x5
-				MX53_PAD_DI0_PIN15__IPU_DI0_PIN15	0x5
-				MX53_PAD_DI0_PIN2__IPU_DI0_PIN2		0x5
-				MX53_PAD_DI0_PIN3__IPU_DI0_PIN3		0x5
-				MX53_PAD_DISP0_DAT0__IPU_DISP0_DAT_0	0x5
-				MX53_PAD_DISP0_DAT1__IPU_DISP0_DAT_1	0x5
-				MX53_PAD_DISP0_DAT2__IPU_DISP0_DAT_2	0x5
-				MX53_PAD_DISP0_DAT3__IPU_DISP0_DAT_3	0x5
-				MX53_PAD_DISP0_DAT4__IPU_DISP0_DAT_4	0x5
-				MX53_PAD_DISP0_DAT5__IPU_DISP0_DAT_5	0x5
-				MX53_PAD_DISP0_DAT6__IPU_DISP0_DAT_6	0x5
-				MX53_PAD_DISP0_DAT7__IPU_DISP0_DAT_7	0x5
-				MX53_PAD_DISP0_DAT8__IPU_DISP0_DAT_8	0x5
-				MX53_PAD_DISP0_DAT9__IPU_DISP0_DAT_9	0x5
-				MX53_PAD_DISP0_DAT10__IPU_DISP0_DAT_10	0x5
-				MX53_PAD_DISP0_DAT11__IPU_DISP0_DAT_11	0x5
-				MX53_PAD_DISP0_DAT12__IPU_DISP0_DAT_12	0x5
-				MX53_PAD_DISP0_DAT13__IPU_DISP0_DAT_13	0x5
-				MX53_PAD_DISP0_DAT14__IPU_DISP0_DAT_14	0x5
-				MX53_PAD_DISP0_DAT15__IPU_DISP0_DAT_15	0x5
-				MX53_PAD_DISP0_DAT16__IPU_DISP0_DAT_16	0x5
-				MX53_PAD_DISP0_DAT17__IPU_DISP0_DAT_17	0x5
-				MX53_PAD_DISP0_DAT18__IPU_DISP0_DAT_18	0x5
-				MX53_PAD_DISP0_DAT19__IPU_DISP0_DAT_19	0x5
-				MX53_PAD_DISP0_DAT20__IPU_DISP0_DAT_20	0x5
-				MX53_PAD_DISP0_DAT21__IPU_DISP0_DAT_21	0x5
-				MX53_PAD_DISP0_DAT22__IPU_DISP0_DAT_22	0x5
-				MX53_PAD_DISP0_DAT23__IPU_DISP0_DAT_23	0x5
-			>;
-		};
-
-		pinctrl_vga_sync: vgasync-grp {
-			fsl,pins = <
-				/* VGA_HSYNC, VSYNC with max drive strength */
-				MX53_PAD_EIM_OE__IPU_DI1_PIN7 0xe6
-				MX53_PAD_EIM_RW__IPU_DI1_PIN8 0xe6
-			>;
-		};
-
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX53_PAD_CSI0_DAT10__UART1_TXD_MUX	0x1e4
-				MX53_PAD_CSI0_DAT11__UART1_RXD_MUX	0x1e4
-			>;
-		};
-	};
-};
-
-&tve {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_vga_sync>;
-	ddc-i2c-bus = <&i2c2>;
-	fsl,tve-mode = "vga";
-	fsl,hsync-pin = <7>;	/* IPU DI1 PIN7 via EIM_OE */
-	fsl,vsync-pin = <8>;	/* IPU DI1 PIN8 via EIM_RW */
-	status = "okay";
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
-	status = "okay";
-};
-
-&i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c2>;
-	status = "okay";
-
-	sgtl5000: codec@a {
-		compatible = "fsl,sgtl5000";
-		reg = <0x0a>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_codec>;
-		#sound-dai-cells = <0>;
-		VDDA-supply = <&reg_3p2v>;
-		VDDIO-supply = <&reg_3p2v>;
-		clocks = <&clks IMX5_CLK_SSI_EXT1_GATE>;
-	};
-};
-
-&i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c1>;
-	status = "okay";
-
-	accelerometer: mma8450@1c {
-		compatible = "fsl,mma8450";
-		reg = <0x1c>;
-	};
-};
-
-&audmux {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_audmux>;
-	status = "okay";
-};
-
-&fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_fec>;
-	phy-mode = "rmii";
-	phy-reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-&sata {
-	status = "okay";
-};
-
-&vpu {
-	status = "okay";
-};
-
-&usbh1 {
-	vbus-supply = <&reg_usb_vbus>;
-	phy_type = "utmi";
-	status = "okay";
-};
-
-&usbotg {
-	dr_mode = "peripheral";
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx53-smd.dts b/arch/arm/boot/dts/imx53-smd.dts
deleted file mode 100644
index 9be44e807188..000000000000
--- a/arch/arm/boot/dts/imx53-smd.dts
+++ /dev/null
@@ -1,346 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-//
-// Copyright 2011 Freescale Semiconductor, Inc.
-// Copyright 2011 Linaro Ltd.
-
-/dts-v1/;
-#include <dt-bindings/input/input.h>
-#include "imx53.dtsi"
-
-/ {
-	model = "Freescale i.MX53 Smart Mobile Reference Design Board";
-	compatible = "fsl,imx53-smd", "fsl,imx53";
-
-	memory@70000000 {
-		device_type = "memory";
-		reg = <0x70000000 0x40000000>;
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		volume-up {
-			label = "Volume Up";
-			gpios = <&gpio2 14 0>;
-			linux,code = <KEY_VOLUMEUP>;
-		};
-
-		volume-down {
-			label = "Volume Down";
-			gpios = <&gpio2 15 0>;
-			linux,code = <KEY_VOLUMEDOWN>;
-		};
-	};
-};
-
-&esdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_esdhc1>;
-	cd-gpios = <&gpio3 13 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio4 11 GPIO_ACTIVE_HIGH>;
-	status = "okay";
-};
-
-&esdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_esdhc2>;
-	non-removable;
-	status = "okay";
-};
-
-&uart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart3>;
-	uart-has-rtscts;
-	status = "okay";
-};
-
-&ecspi1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi1>;
-	cs-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>, <&gpio3 19 GPIO_ACTIVE_LOW>;
-	status = "okay";
-
-	zigbee: mc1323@0 {
-		compatible = "fsl,mc1323";
-		spi-max-frequency = <8000000>;
-		reg = <0>;
-	};
-
-	flash: m25p32@1 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "st,m25p32", "st,m25p", "jedec,spi-nor";
-		spi-max-frequency = <20000000>;
-		reg = <1>;
-
-		partition@0 {
-			label = "U-Boot";
-			reg = <0x0 0x40000>;
-			read-only;
-		};
-
-		partition@40000 {
-			label = "Kernel";
-			reg = <0x40000 0x3c0000>;
-		};
-	};
-};
-
-&esdhc3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_esdhc3>;
-	non-removable;
-	status = "okay";
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_hog>;
-
-	imx53-smd {
-		pinctrl_hog: hoggrp {
-			fsl,pins = <
-				MX53_PAD_PATA_DATA14__GPIO2_14 0x80000000
-				MX53_PAD_PATA_DATA15__GPIO2_15 0x80000000
-				MX53_PAD_EIM_EB2__GPIO2_30     0x80000000
-				MX53_PAD_EIM_DA13__GPIO3_13    0x80000000
-				MX53_PAD_EIM_D19__GPIO3_19     0x80000000
-				MX53_PAD_KEY_ROW2__GPIO4_11    0x80000000
-				MX53_PAD_PATA_DA_0__GPIO7_6    0x80000000
-			>;
-		};
-
-		pinctrl_ecspi1: ecspi1grp {
-			fsl,pins = <
-				MX53_PAD_EIM_D16__ECSPI1_SCLK		0x80000000
-				MX53_PAD_EIM_D17__ECSPI1_MISO		0x80000000
-				MX53_PAD_EIM_D18__ECSPI1_MOSI		0x80000000
-			>;
-		};
-
-		pinctrl_esdhc1: esdhc1grp {
-			fsl,pins = <
-				MX53_PAD_SD1_DATA0__ESDHC1_DAT0		0x1d5
-				MX53_PAD_SD1_DATA1__ESDHC1_DAT1		0x1d5
-				MX53_PAD_SD1_DATA2__ESDHC1_DAT2		0x1d5
-				MX53_PAD_SD1_DATA3__ESDHC1_DAT3		0x1d5
-				MX53_PAD_SD1_CMD__ESDHC1_CMD		0x1d5
-				MX53_PAD_SD1_CLK__ESDHC1_CLK		0x1d5
-			>;
-		};
-
-		pinctrl_esdhc2: esdhc2grp {
-			fsl,pins = <
-				MX53_PAD_SD2_CMD__ESDHC2_CMD		0x1d5
-				MX53_PAD_SD2_CLK__ESDHC2_CLK		0x1d5
-				MX53_PAD_SD2_DATA0__ESDHC2_DAT0		0x1d5
-				MX53_PAD_SD2_DATA1__ESDHC2_DAT1		0x1d5
-				MX53_PAD_SD2_DATA2__ESDHC2_DAT2		0x1d5
-				MX53_PAD_SD2_DATA3__ESDHC2_DAT3		0x1d5
-			>;
-		};
-
-		pinctrl_esdhc3: esdhc3grp {
-			fsl,pins = <
-				MX53_PAD_PATA_DATA8__ESDHC3_DAT0	0x1d5
-				MX53_PAD_PATA_DATA9__ESDHC3_DAT1	0x1d5
-				MX53_PAD_PATA_DATA10__ESDHC3_DAT2	0x1d5
-				MX53_PAD_PATA_DATA11__ESDHC3_DAT3	0x1d5
-				MX53_PAD_PATA_DATA0__ESDHC3_DAT4	0x1d5
-				MX53_PAD_PATA_DATA1__ESDHC3_DAT5	0x1d5
-				MX53_PAD_PATA_DATA2__ESDHC3_DAT6	0x1d5
-				MX53_PAD_PATA_DATA3__ESDHC3_DAT7	0x1d5
-				MX53_PAD_PATA_RESET_B__ESDHC3_CMD	0x1d5
-				MX53_PAD_PATA_IORDY__ESDHC3_CLK		0x1d5
-			>;
-		};
-
-		pinctrl_fec: fecgrp {
-			fsl,pins = <
-				MX53_PAD_FEC_MDC__FEC_MDC		0x80000000
-				MX53_PAD_FEC_MDIO__FEC_MDIO		0x80000000
-				MX53_PAD_FEC_REF_CLK__FEC_TX_CLK	0x80000000
-				MX53_PAD_FEC_RX_ER__FEC_RX_ER		0x80000000
-				MX53_PAD_FEC_CRS_DV__FEC_RX_DV		0x80000000
-				MX53_PAD_FEC_RXD1__FEC_RDATA_1		0x80000000
-				MX53_PAD_FEC_RXD0__FEC_RDATA_0		0x80000000
-				MX53_PAD_FEC_TX_EN__FEC_TX_EN		0x80000000
-				MX53_PAD_FEC_TXD1__FEC_TDATA_1		0x80000000
-				MX53_PAD_FEC_TXD0__FEC_TDATA_0		0x80000000
-			>;
-		};
-
-		pinctrl_i2c1: i2c1grp {
-			fsl,pins = <
-				MX53_PAD_CSI0_DAT8__I2C1_SDA		0xc0000000
-				MX53_PAD_CSI0_DAT9__I2C1_SCL		0xc0000000
-			>;
-		};
-
-		pinctrl_i2c2: i2c2grp {
-			fsl,pins = <
-				MX53_PAD_KEY_ROW3__I2C2_SDA		0xc0000000
-				MX53_PAD_KEY_COL3__I2C2_SCL		0xc0000000
-			>;
-		};
-
-		pinctrl_ipu_csi0: ipucsi0grp {
-			fsl,pins = <
-				MX53_PAD_CSI0_DAT12__IPU_CSI0_D_12    0x1c4
-				MX53_PAD_CSI0_DAT13__IPU_CSI0_D_13    0x1c4
-				MX53_PAD_CSI0_DAT14__IPU_CSI0_D_14    0x1c4
-				MX53_PAD_CSI0_DAT15__IPU_CSI0_D_15    0x1c4
-				MX53_PAD_CSI0_DAT16__IPU_CSI0_D_16    0x1c4
-				MX53_PAD_CSI0_DAT17__IPU_CSI0_D_17    0x1c4
-				MX53_PAD_CSI0_DAT18__IPU_CSI0_D_18    0x1c4
-				MX53_PAD_CSI0_DAT19__IPU_CSI0_D_19    0x1c4
-				MX53_PAD_CSI0_PIXCLK__IPU_CSI0_PIXCLK 0x1e4
-				MX53_PAD_CSI0_VSYNC__IPU_CSI0_VSYNC   0x1e4
-				MX53_PAD_CSI0_MCLK__IPU_CSI0_HSYNC    0x1e4
-				MX53_PAD_CSI0_DATA_EN__IPU_CSI0_DATA_EN 0x1e4
-			>;
-		};
-
-		pinctrl_ov5642: ov5642grp {
-			fsl,pins = <
-				MX53_PAD_NANDF_WP_B__GPIO6_9   0x1e4
-				MX53_PAD_NANDF_RB0__GPIO6_10   0x1e4
-				MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK 0x1c4
-			>;
-		};
-
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX53_PAD_CSI0_DAT10__UART1_TXD_MUX	0x1e4
-				MX53_PAD_CSI0_DAT11__UART1_RXD_MUX	0x1e4
-			>;
-		};
-
-		pinctrl_uart2: uart2grp {
-			fsl,pins = <
-				MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX	0x1e4
-				MX53_PAD_PATA_DMARQ__UART2_TXD_MUX	0x1e4
-			>;
-		};
-
-		pinctrl_uart3: uart3grp {
-			fsl,pins = <
-				MX53_PAD_PATA_CS_0__UART3_TXD_MUX	0x1e4
-				MX53_PAD_PATA_CS_1__UART3_RXD_MUX	0x1e4
-				MX53_PAD_PATA_DA_1__UART3_CTS		0x1e4
-				MX53_PAD_PATA_DA_2__UART3_RTS		0x1e4
-			>;
-		};
-	};
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
-	status = "okay";
-};
-
-&uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
-	status = "okay";
-};
-
-&i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c2>;
-	status = "okay";
-
-	codec: sgtl5000@a {
-		compatible = "fsl,sgtl5000";
-		reg = <0x0a>;
-	};
-
-	magnetometer: mag3110@e {
-		compatible = "fsl,mag3110";
-		reg = <0x0e>;
-	};
-
-	touchkey: mpr121@5a {
-		compatible = "fsl,mpr121";
-		reg = <0x5a>;
-	};
-};
-
-&i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c1>;
-	status = "okay";
-
-	accelerometer: mma8450@1c {
-		compatible = "fsl,mma8450";
-		reg = <0x1c>;
-	};
-
-	camera: ov5642@3c {
-		compatible = "ovti,ov5642";
-		reg = <0x3c>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_ov5642>;
-		assigned-clocks = <&clks IMX5_CLK_SSI_EXT1_SEL>,
-				  <&clks IMX5_CLK_SSI_EXT1_COM_SEL>;
-		assigned-clock-parents = <&clks IMX5_CLK_PLL2_SW>,
-					 <&clks IMX5_CLK_SSI_EXT1_PODF>;
-		assigned-clock-rates = <0>, <24000000>;
-		clocks = <&clks IMX5_CLK_SSI_EXT1_GATE>;
-		clock-names = "xclk";
-		DVDD-supply = <&ldo9_reg>;
-		AVDD-supply = <&ldo7_reg>;
-		reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>;
-		powerdown-gpios = <&gpio6 10 GPIO_ACTIVE_HIGH>;
-
-		port {
-			ov5642_to_ipu_csi0: endpoint {
-				remote-endpoint = <&ipu_csi0_from_parallel_sensor>;
-				bus-width = <8>;
-				hsync-active = <1>;
-				vsync-active = <1>;
-			};
-		};
-	};
-
-	pmic: dialog@48 {
-		compatible = "dlg,da9053", "dlg,da9052";
-		reg = <0x48>;
-		interrupt-parent = <&gpio7>;
-		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
-
-		regulators {
-			ldo7_reg: ldo7 {
-				regulator-min-microvolt = <1200000>;
-				regulator-max-microvolt = <3600000>;
-			};
-
-			ldo9_reg: ldo9 {
-				regulator-min-microvolt = <1250000>;
-				regulator-max-microvolt = <3650000>;
-			};
-		};
-	};
-};
-
-&fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_fec>;
-	phy-mode = "rmii";
-	phy-reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-&ipu_csi0_from_parallel_sensor {
-	remote-endpoint = <&ov5642_to_ipu_csi0>;
-	data-shift = <12>; /* Lines 19:12 used */
-	hsync-active = <1>;
-	vsync-active = <1>;
-};
-
-&ipu_csi0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ipu_csi0>;
-};
diff --git a/arch/arm/boot/dts/imx53-tqma53.dtsi b/arch/arm/boot/dts/imx53-tqma53.dtsi
deleted file mode 100644
index 7e7f9f3b3906..000000000000
--- a/arch/arm/boot/dts/imx53-tqma53.dtsi
+++ /dev/null
@@ -1,289 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2012 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
- * Copyright 2012 Steffen Trumtrar <s.trumtrar@pengutronix.de>, Pengutronix
- */
-
-#include "imx53.dtsi"
-
-/ {
-	model = "TQ TQMa53";
-	compatible = "tq,tqma53", "fsl,imx53";
-
-	memory@70000000 {
-		device_type = "memory";
-		reg = <0x70000000 0x40000000>; /* Up to 1GiB */
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-	};
-};
-
-&esdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_esdhc2>,
-		    <&pinctrl_esdhc2_cdwp>;
-	vmmc-supply = <&reg_3p3v>;
-	wp-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
-	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
-	status = "disabled";
-};
-
-&uart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart3>;
-	status = "disabled";
-};
-
-&ecspi1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi1>;
-	cs-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>, <&gpio3 19 GPIO_ACTIVE_LOW>,
-		   <&gpio3 24 GPIO_ACTIVE_LOW>, <&gpio3 25 GPIO_ACTIVE_LOW>;
-	status = "disabled";
-};
-
-&esdhc3 { /* EMMC */
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_esdhc3>;
-	vmmc-supply = <&reg_3p3v>;
-	non-removable;
-	bus-width = <8>;
-	status = "okay";
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_hog>;
-
-	imx53-tqma53 {
-		pinctrl_hog: hoggrp {
-			fsl,pins = <
-				 MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK 0x80000000 /* SSI_MCLK */
-				 MX53_PAD_PATA_DA_1__GPIO7_7     0x80000000 /* LCD_BLT_EN */
-				 MX53_PAD_PATA_DA_2__GPIO7_8     0x80000000 /* LCD_RESET */
-				 MX53_PAD_PATA_DATA5__GPIO2_5    0x80000000 /* LCD_POWER */
-				 MX53_PAD_PATA_DATA6__GPIO2_6    0x80000000 /* PMIC_INT */
-				 MX53_PAD_PATA_DATA14__GPIO2_14  0x80000000 /* CSI_RST */
-				 MX53_PAD_PATA_DATA15__GPIO2_15  0x80000000 /* CSI_PWDN */
-				 MX53_PAD_GPIO_19__GPIO4_5 	 0x80000000 /* #SYSTEM_DOWN */
-				 MX53_PAD_GPIO_3__GPIO1_3        0x80000000
-				 MX53_PAD_PATA_DA_0__GPIO7_6	 0x80000000 /* #PHY_RESET */
-				 MX53_PAD_GPIO_1__PWM2_PWMO	 0x80000000 /* LCD_CONTRAST */
-			>;
-		};
-
-		pinctrl_audmux: audmuxgrp {
-			fsl,pins = <
-				MX53_PAD_KEY_COL0__AUDMUX_AUD5_TXC	0x80000000
-				MX53_PAD_KEY_ROW0__AUDMUX_AUD5_TXD	0x80000000
-				MX53_PAD_KEY_COL1__AUDMUX_AUD5_TXFS	0x80000000
-				MX53_PAD_KEY_ROW1__AUDMUX_AUD5_RXD	0x80000000
-			>;
-		};
-
-		pinctrl_can1: can1grp {
-			fsl,pins = <
-				MX53_PAD_KEY_COL2__CAN1_TXCAN		0x80000000
-				MX53_PAD_KEY_ROW2__CAN1_RXCAN		0x80000000
-			>;
-		};
-
-		pinctrl_can2: can2grp {
-			fsl,pins = <
-				MX53_PAD_KEY_COL4__CAN2_TXCAN		0x80000000
-				MX53_PAD_KEY_ROW4__CAN2_RXCAN		0x80000000
-			>;
-		};
-
-		pinctrl_cspi: cspigrp {
-			fsl,pins = <
-				MX53_PAD_SD1_DATA0__CSPI_MISO		0x1d5
-				MX53_PAD_SD1_CMD__CSPI_MOSI		0x1d5
-				MX53_PAD_SD1_CLK__CSPI_SCLK		0x1d5
-			>;
-		};
-
-		pinctrl_ecspi1: ecspi1grp {
-			fsl,pins = <
-				MX53_PAD_EIM_D16__ECSPI1_SCLK		0x80000000
-				MX53_PAD_EIM_D17__ECSPI1_MISO		0x80000000
-				MX53_PAD_EIM_D18__ECSPI1_MOSI		0x80000000
-			>;
-		};
-
-		pinctrl_esdhc2: esdhc2grp {
-			fsl,pins = <
-				MX53_PAD_SD2_CMD__ESDHC2_CMD		0x1d5
-				MX53_PAD_SD2_CLK__ESDHC2_CLK		0x1d5
-				MX53_PAD_SD2_DATA0__ESDHC2_DAT0		0x1d5
-				MX53_PAD_SD2_DATA1__ESDHC2_DAT1		0x1d5
-				MX53_PAD_SD2_DATA2__ESDHC2_DAT2		0x1d5
-				MX53_PAD_SD2_DATA3__ESDHC2_DAT3		0x1d5
-			>;
-		};
-
-		pinctrl_esdhc2_cdwp: esdhc2cdwp {
-			fsl,pins = <
-				MX53_PAD_GPIO_4__GPIO1_4	0x80000000 /* SD2_CD */
-				MX53_PAD_GPIO_2__GPIO1_2	0x80000000 /* SD2_WP */
-			>;
-		};
-
-		pinctrl_esdhc3: esdhc3grp {
-			fsl,pins = <
-				MX53_PAD_PATA_DATA8__ESDHC3_DAT0	0x1d5
-				MX53_PAD_PATA_DATA9__ESDHC3_DAT1	0x1d5
-				MX53_PAD_PATA_DATA10__ESDHC3_DAT2	0x1d5
-				MX53_PAD_PATA_DATA11__ESDHC3_DAT3	0x1d5
-				MX53_PAD_PATA_DATA0__ESDHC3_DAT4	0x1d5
-				MX53_PAD_PATA_DATA1__ESDHC3_DAT5	0x1d5
-				MX53_PAD_PATA_DATA2__ESDHC3_DAT6	0x1d5
-				MX53_PAD_PATA_DATA3__ESDHC3_DAT7	0x1d5
-				MX53_PAD_PATA_RESET_B__ESDHC3_CMD	0x1d5
-				MX53_PAD_PATA_IORDY__ESDHC3_CLK		0x1d5
-			>;
-		};
-
-		pinctrl_fec: fecgrp {
-			fsl,pins = <
-				MX53_PAD_FEC_MDC__FEC_MDC		0x80000000
-				MX53_PAD_FEC_MDIO__FEC_MDIO		0x80000000
-				MX53_PAD_FEC_REF_CLK__FEC_TX_CLK	0x80000000
-				MX53_PAD_FEC_RX_ER__FEC_RX_ER		0x80000000
-				MX53_PAD_FEC_CRS_DV__FEC_RX_DV		0x80000000
-				MX53_PAD_FEC_RXD1__FEC_RDATA_1		0x80000000
-				MX53_PAD_FEC_RXD0__FEC_RDATA_0		0x80000000
-				MX53_PAD_FEC_TX_EN__FEC_TX_EN		0x80000000
-				MX53_PAD_FEC_TXD1__FEC_TDATA_1		0x80000000
-				MX53_PAD_FEC_TXD0__FEC_TDATA_0		0x80000000
-			>;
-		};
-
-		pinctrl_i2c2: i2c2grp {
-			fsl,pins = <
-				MX53_PAD_KEY_ROW3__I2C2_SDA		0xc0000000
-				MX53_PAD_KEY_COL3__I2C2_SCL		0xc0000000
-			>;
-		};
-
-		pinctrl_i2c3: i2c3grp {
-			fsl,pins = <
-				MX53_PAD_GPIO_6__I2C3_SDA		0xc0000000
-				MX53_PAD_GPIO_5__I2C3_SCL		0xc0000000
-			>;
-		};
-
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX53_PAD_PATA_DIOW__UART1_TXD_MUX	0x1e4
-				MX53_PAD_PATA_DMACK__UART1_RXD_MUX	0x1e4
-			>;
-		};
-
-		pinctrl_uart2: uart2grp {
-			fsl,pins = <
-				MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX	0x1e4
-				MX53_PAD_PATA_DMARQ__UART2_TXD_MUX	0x1e4
-			>;
-		};
-
-		pinctrl_uart3: uart3grp {
-			fsl,pins = <
-				MX53_PAD_PATA_CS_0__UART3_TXD_MUX	0x1e4
-				MX53_PAD_PATA_CS_1__UART3_RXD_MUX	0x1e4
-			>;
-		};
-	};
-};
-
-&pwm1 {
-	#pwm-cells = <2>;
-};
-
-&pwm2 {
-	#pwm-cells = <2>;
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
-	uart-has-rtscts;
-	status = "disabled";
-};
-
-&uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
-	status = "disabled";
-};
-
-&can1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_can1>;
-	status = "disabled";
-};
-
-&can2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_can2>;
-	status = "disabled";
-};
-
-&i2c3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c3>;
-	status = "disabled";
-};
-
-&cspi {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_cspi>;
-	cs-gpios = <&gpio1 18 GPIO_ACTIVE_LOW>, <&gpio1 19 GPIO_ACTIVE_LOW>,
-		   <&gpio1 21 GPIO_ACTIVE_LOW>;
-	status = "disabled";
-};
-
-&i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c2>;
-	status = "okay";
-
-	pmic: mc34708@8 {
-		compatible = "fsl,mc34708";
-		reg = <0x8>;
-		fsl,mc13xxx-uses-rtc;
-		interrupt-parent = <&gpio2>;
-		interrupts = <6 4>; /* PATA_DATA6, active high */
-	};
-
-	sensor1: lm75@48 {
-		compatible = "lm75";
-		reg = <0x48>;
-	};
-
-	eeprom: 24c64@50 {
-		compatible = "atmel,24c64";
-		pagesize = <32>;
-		reg = <0x50>;
-	};
-};
-
-&fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_fec>;
-	phy-mode = "rmii";
-	status = "disabled";
-};
diff --git a/arch/arm/boot/dts/imx53-tx53.dtsi b/arch/arm/boot/dts/imx53-tx53.dtsi
deleted file mode 100644
index 8712e9851465..000000000000
--- a/arch/arm/boot/dts/imx53-tx53.dtsi
+++ /dev/null
@@ -1,584 +0,0 @@
-/*
- * Copyright 2012-2017 <LW@KARO-electronics.de>
- * based on imx53-qsb.dts
- *   Copyright 2011 Freescale Semiconductor, Inc.
- *   Copyright 2011 Linaro Ltd.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#include "imx53.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
-	model = "Ka-Ro electronics TX53 module";
-	compatible = "karo,tx53", "fsl,imx53";
-
-	/* Will be filled by the bootloader */
-	memory@70000000 {
-		device_type = "memory";
-		reg = <0x70000000 0>;
-	};
-
-	aliases {
-		can0 = &can2; /* Make the can interface indices consistent with TX28/TX48 modules */
-		can1 = &can1;
-		ipu = &ipu;
-		reg-can-xcvr = &reg_can_xcvr;
-		usbh1 = &usbh1;
-		usbotg = &usbotg;
-	};
-
-	clocks {
-		ckih1 {
-			clock-frequency = <0>;
-		};
-	};
-
-	mclk: clock-mclk {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <26000000>;
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpio_key>;
-
-		power {
-			label = "Power Button";
-			gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>;
-			linux,code = <116>; /* KEY_POWER */
-			wakeup-source;
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_stk5led>;
-
-		user {
-			label = "Heartbeat";
-			gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-		};
-	};
-
-	reg_2v5: regulator-2v5 {
-		compatible = "regulator-fixed";
-		regulator-name = "2V5";
-		regulator-min-microvolt = <2500000>;
-		regulator-max-microvolt = <2500000>;
-	};
-
-	reg_3v3: regulator-3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "3V3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	reg_can_xcvr: regulator-can-xcvr {
-		compatible = "regulator-fixed";
-		regulator-name = "CAN XCVR";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_can_xcvr>;
-		gpio = <&gpio4 21 GPIO_ACTIVE_HIGH>;
-	};
-
-	reg_usbh1_vbus: regulator-usbh1-vbus {
-		compatible = "regulator-fixed";
-		regulator-name = "usbh1_vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_usbh1_vbus>;
-		gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	reg_usbotg_vbus: regulator-usbotg-vbus {
-		compatible = "regulator-fixed";
-		regulator-name = "usbotg_vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_usbotg_vbus>;
-		gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	sound {
-		compatible = "karo,tx53-audio-sgtl5000", "fsl,imx-audio-sgtl5000";
-		model = "tx53-audio-sgtl5000";
-		ssi-controller = <&ssi1>;
-		audio-codec = <&sgtl5000>;
-		audio-routing =
-			"MIC_IN", "Mic Jack",
-			"Mic Jack", "Mic Bias",
-			"Headphone Jack", "HP_OUT";
-		/* '1' based port numbers according to datasheet names */
-		mux-int-port = <1>;
-		mux-ext-port = <5>;
-	};
-};
-
-&audmux {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ssi1>;
-	status = "okay";
-};
-
-&can1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_can1>;
-	xceiver-supply = <&reg_can_xcvr>;
-	status = "okay";
-};
-
-&can2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_can2>;
-	xceiver-supply = <&reg_can_xcvr>;
-	status = "okay";
-};
-
-&ecspi1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi1>;
-	status = "okay";
-
-	cs-gpios = <
-		&gpio2 30 GPIO_ACTIVE_HIGH
-		&gpio3 19 GPIO_ACTIVE_HIGH
-	>;
-
-};
-
-&esdhc1 {
-	cd-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
-	fsl,wp-controller;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_esdhc1>;
-	status = "okay";
-};
-
-&esdhc2 {
-	cd-gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
-	fsl,wp-controller;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_esdhc2>;
-	status = "okay";
-};
-
-&fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_fec>;
-	phy-mode = "rmii";
-	phy-reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
-	phy-handle = <&phy0>;
-	mac-address = [000000000000]; /* placeholder; will be overwritten by bootloader */
-	status = "okay";
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		phy0: ethernet-phy@0 {
-			reg = <0>;
-			interrupt-parent = <&gpio2>;
-			interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
-			device_type = "ethernet-phy";
-		};
-	};
-};
-
-&i2c1 {
-	pinctrl-names = "default", "gpio";
-	pinctrl-0 = <&pinctrl_i2c1>;
-	pinctrl-0 = <&pinctrl_i2c1_gpio>;
-	scl-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
-	sda-gpios = <&gpio3 28 GPIO_ACTIVE_HIGH>;
-	clock-frequency = <400000>;
-	status = "okay";
-
-	rtc1: rtc@68 {
-		compatible = "dallas,ds1339";
-		reg = <0x68>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_ds1339>;
-		interrupt-parent = <&gpio4>;
-		interrupts = <20 IRQ_TYPE_EDGE_FALLING>;
-		trickle-resistor-ohms = <250>;
-		trickle-diode-disable;
-	};
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_hog>;
-
-	imx53-tx53 {
-		pinctrl_hog: hoggrp {
-			/* pins not in use by any device on the Starterkit board series */
-			fsl,pins = <
-				/* CMOS Sensor Interface */
-				MX53_PAD_CSI0_DAT12__GPIO5_30 0x1f4
-				MX53_PAD_CSI0_DAT13__GPIO5_31 0x1f4
-				MX53_PAD_CSI0_DAT14__GPIO6_0 0x1f4
-				MX53_PAD_CSI0_DAT15__GPIO6_1 0x1f4
-				MX53_PAD_CSI0_DAT16__GPIO6_2 0x1f4
-				MX53_PAD_CSI0_DAT17__GPIO6_3 0x1f4
-				MX53_PAD_CSI0_DAT18__GPIO6_4 0x1f4
-				MX53_PAD_CSI0_DAT19__GPIO6_5 0x1f4
-				MX53_PAD_CSI0_MCLK__GPIO5_19 0x1f4
-				MX53_PAD_CSI0_VSYNC__GPIO5_21 0x1f4
-				MX53_PAD_CSI0_PIXCLK__GPIO5_18 0x1f4
-				MX53_PAD_GPIO_0__GPIO1_0 0x1f4
-				/* Module Specific Signal */
-				/* MX53_PAD_NANDF_CS2__GPIO6_15 0x1f4 maybe used by EDT-FT5x06 */
-				/* MX53_PAD_EIM_A16__GPIO2_22 0x1f4 maybe used by EDT-FT5x06 */
-				MX53_PAD_EIM_D29__GPIO3_29 0x1f4
-				MX53_PAD_EIM_EB3__GPIO2_31 0x1f4
-				/* MX53_PAD_EIM_A17__GPIO2_21 0x1f4 maybe used by EDT-FT5x06 */
-				/* MX53_PAD_EIM_A18__GPIO2_20 0x1f4 used by LED */
-				MX53_PAD_EIM_A19__GPIO2_19 0x1f4
-				MX53_PAD_EIM_A20__GPIO2_18 0x1f4
-				MX53_PAD_EIM_A21__GPIO2_17 0x1f4
-				MX53_PAD_EIM_A22__GPIO2_16 0x1f4
-				MX53_PAD_EIM_A23__GPIO6_6 0x1f4
-				MX53_PAD_EIM_A24__GPIO5_4 0x1f4
-				MX53_PAD_CSI0_DAT8__GPIO5_26 0x1f4
-				MX53_PAD_CSI0_DAT9__GPIO5_27 0x1f4
-				MX53_PAD_CSI0_DAT10__GPIO5_28 0x1f4
-				MX53_PAD_CSI0_DAT11__GPIO5_29 0x1f4
-				/* MX53_PAD_EIM_D22__GPIO3_22 0x1f4 maybe used by EETI touchpanel driver */
-				/* MX53_PAD_EIM_D23__GPIO3_23 0x1f4 maybe used by EETI touchpanel driver */
-				MX53_PAD_GPIO_13__GPIO4_3 0x1f4
-				MX53_PAD_EIM_CS0__GPIO2_23 0x1f4
-				MX53_PAD_EIM_CS1__GPIO2_24 0x1f4
-				MX53_PAD_CSI0_DATA_EN__GPIO5_20 0x1f4
-				MX53_PAD_EIM_WAIT__GPIO5_0 0x1f4
-				MX53_PAD_EIM_EB0__GPIO2_28 0x1f4
-				MX53_PAD_EIM_EB1__GPIO2_29 0x1f4
-				MX53_PAD_EIM_OE__GPIO2_25 0x1f4
-				MX53_PAD_EIM_LBA__GPIO2_27 0x1f4
-				MX53_PAD_EIM_RW__GPIO2_26 0x1f4
-				MX53_PAD_EIM_DA8__GPIO3_8 0x1f4
-				MX53_PAD_EIM_DA9__GPIO3_9 0x1f4
-				MX53_PAD_EIM_DA10__GPIO3_10 0x1f4
-				MX53_PAD_EIM_DA11__GPIO3_11 0x1f4
-				MX53_PAD_EIM_DA12__GPIO3_12 0x1f4
-				MX53_PAD_EIM_DA13__GPIO3_13 0x1f4
-				MX53_PAD_EIM_DA14__GPIO3_14 0x1f4
-				MX53_PAD_EIM_DA15__GPIO3_15 0x1f4
-				>;
-		};
-
-		pinctrl_can1: can1grp {
-			fsl,pins = <
-				MX53_PAD_GPIO_7__CAN1_TXCAN		0x80000000
-				MX53_PAD_GPIO_8__CAN1_RXCAN		0x80000000
-			>;
-		};
-
-		pinctrl_can2: can2grp {
-			fsl,pins = <
-				MX53_PAD_KEY_COL4__CAN2_TXCAN		0x80000000
-				MX53_PAD_KEY_ROW4__CAN2_RXCAN		0x80000000
-			>;
-		};
-
-		pinctrl_can_xcvr: can-xcvrgrp {
-			fsl,pins = <MX53_PAD_DISP0_DAT0__GPIO4_21 0xe0>; /* Flexcan XCVR enable */
-		};
-
-		pinctrl_ds1339: ds1339grp {
-			fsl,pins = <MX53_PAD_DI0_PIN4__GPIO4_20 0xe0>;
-		};
-
-		pinctrl_ecspi1: ecspi1grp {
-			fsl,pins = <
-				MX53_PAD_GPIO_19__ECSPI1_RDY		0x80000000
-				MX53_PAD_EIM_EB2__ECSPI1_SS0		0x80000000
-				MX53_PAD_EIM_D16__ECSPI1_SCLK		0x80000000
-				MX53_PAD_EIM_D17__ECSPI1_MISO		0x80000000
-				MX53_PAD_EIM_D18__ECSPI1_MOSI		0x80000000
-				MX53_PAD_EIM_D19__ECSPI1_SS1		0x80000000
-			>;
-		};
-
-		pinctrl_esdhc1: esdhc1grp {
-			fsl,pins = <
-				MX53_PAD_SD1_DATA0__ESDHC1_DAT0		0x1d5
-				MX53_PAD_SD1_DATA1__ESDHC1_DAT1		0x1d5
-				MX53_PAD_SD1_DATA2__ESDHC1_DAT2		0x1d5
-				MX53_PAD_SD1_DATA3__ESDHC1_DAT3		0x1d5
-				MX53_PAD_SD1_CMD__ESDHC1_CMD		0x1d5
-				MX53_PAD_SD1_CLK__ESDHC1_CLK		0x1d5
-				MX53_PAD_EIM_D24__GPIO3_24 0x1f0
-			>;
-		};
-
-		pinctrl_esdhc2: esdhc2grp {
-			fsl,pins = <
-				MX53_PAD_SD2_CMD__ESDHC2_CMD		0x1d5
-				MX53_PAD_SD2_CLK__ESDHC2_CLK		0x1d5
-				MX53_PAD_SD2_DATA0__ESDHC2_DAT0		0x1d5
-				MX53_PAD_SD2_DATA1__ESDHC2_DAT1		0x1d5
-				MX53_PAD_SD2_DATA2__ESDHC2_DAT2		0x1d5
-				MX53_PAD_SD2_DATA3__ESDHC2_DAT3		0x1d5
-				MX53_PAD_EIM_D25__GPIO3_25 0x1f0
-			>;
-		};
-
-		pinctrl_fec: fecgrp {
-			fsl,pins = <
-				MX53_PAD_FEC_MDC__FEC_MDC		0x80000000
-				MX53_PAD_FEC_MDIO__FEC_MDIO		0x80000000
-				MX53_PAD_FEC_REF_CLK__FEC_TX_CLK	0x80000000
-				MX53_PAD_FEC_RX_ER__FEC_RX_ER		0x80000000
-				MX53_PAD_FEC_CRS_DV__FEC_RX_DV		0x80000000
-				MX53_PAD_FEC_RXD1__FEC_RDATA_1		0x80000000
-				MX53_PAD_FEC_RXD0__FEC_RDATA_0		0x80000000
-				MX53_PAD_FEC_TX_EN__FEC_TX_EN		0x80000000
-				MX53_PAD_FEC_TXD1__FEC_TDATA_1		0x80000000
-				MX53_PAD_FEC_TXD0__FEC_TDATA_0		0x80000000
-			>;
-		};
-
-		pinctrl_gpio_key: gpio-keygrp {
-			fsl,pins = <MX53_PAD_EIM_A25__GPIO5_2 0x1f4>;
-		};
-
-		pinctrl_i2c1: i2c1grp {
-			fsl,pins = <
-				MX53_PAD_EIM_D21__I2C1_SCL		0x400001e4
-				MX53_PAD_EIM_D28__I2C1_SDA		0x400001e4
-			>;
-		};
-
-		pinctrl_i2c1_gpio: i2c1-gpiogrp {
-			fsl,pins = <
-				MX53_PAD_EIM_D21__GPIO3_21		0x400001e6
-				MX53_PAD_EIM_D28__GPIO3_28		0x400001e6
-			>;
-		};
-
-		pinctrl_i2c3: i2c3grp {
-			fsl,pins = <
-				MX53_PAD_GPIO_3__I2C3_SCL		0x400001e4
-				MX53_PAD_GPIO_6__I2C3_SDA		0x400001e4
-			>;
-		};
-
-		pinctrl_i2c3_gpio: i2c3-gpiogrp {
-			fsl,pins = <
-				MX53_PAD_GPIO_3__GPIO1_3		0x400001e6
-				MX53_PAD_GPIO_6__GPIO1_6		0x400001e6
-			>;
-		};
-
-		pinctrl_nand: nandgrp {
-			fsl,pins = <
-				MX53_PAD_NANDF_WE_B__EMI_NANDF_WE_B	0x4
-				MX53_PAD_NANDF_RE_B__EMI_NANDF_RE_B	0x4
-				MX53_PAD_NANDF_CLE__EMI_NANDF_CLE	0x4
-				MX53_PAD_NANDF_ALE__EMI_NANDF_ALE	0x4
-				MX53_PAD_NANDF_WP_B__EMI_NANDF_WP_B	0xe0
-				MX53_PAD_NANDF_RB0__EMI_NANDF_RB_0	0xe0
-				MX53_PAD_NANDF_CS0__EMI_NANDF_CS_0	0x4
-				MX53_PAD_EIM_DA0__EMI_NAND_WEIM_DA_0	0xa4
-				MX53_PAD_EIM_DA1__EMI_NAND_WEIM_DA_1	0xa4
-				MX53_PAD_EIM_DA2__EMI_NAND_WEIM_DA_2	0xa4
-				MX53_PAD_EIM_DA3__EMI_NAND_WEIM_DA_3	0xa4
-				MX53_PAD_EIM_DA4__EMI_NAND_WEIM_DA_4	0xa4
-				MX53_PAD_EIM_DA5__EMI_NAND_WEIM_DA_5	0xa4
-				MX53_PAD_EIM_DA6__EMI_NAND_WEIM_DA_6	0xa4
-				MX53_PAD_EIM_DA7__EMI_NAND_WEIM_DA_7	0xa4
-			>;
-		};
-
-		pinctrl_pwm2: pwm2grp {
-			fsl,pins = <
-				MX53_PAD_GPIO_1__PWM2_PWMO		0x80000000
-			>;
-		};
-
-		pinctrl_ssi1: ssi1grp {
-			fsl,pins = <
-				MX53_PAD_KEY_COL0__AUDMUX_AUD5_TXC	0x80000000
-				MX53_PAD_KEY_ROW0__AUDMUX_AUD5_TXD	0x80000000
-				MX53_PAD_KEY_COL1__AUDMUX_AUD5_TXFS	0x80000000
-				MX53_PAD_KEY_ROW1__AUDMUX_AUD5_RXD	0x80000000
-			>;
-		};
-
-		pinctrl_ssi2: ssi2grp {
-			fsl,pins = <
-				MX53_PAD_CSI0_DAT4__AUDMUX_AUD3_TXC	0x80000000
-				MX53_PAD_CSI0_DAT5__AUDMUX_AUD3_TXD	0x80000000
-				MX53_PAD_CSI0_DAT6__AUDMUX_AUD3_TXFS	0x80000000
-				MX53_PAD_CSI0_DAT7__AUDMUX_AUD3_RXD	0x80000000
-				MX53_PAD_EIM_D27__GPIO3_27 0x1f0
-			>;
-		};
-
-		pinctrl_stk5led: stk5ledgrp {
-			fsl,pins = <MX53_PAD_EIM_A18__GPIO2_20 0xc0>;
-		};
-
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX53_PAD_PATA_DIOW__UART1_TXD_MUX	0x1e4
-				MX53_PAD_PATA_DMACK__UART1_RXD_MUX	0x1e4
-				MX53_PAD_PATA_RESET_B__UART1_CTS	0x1c5
-				MX53_PAD_PATA_IORDY__UART1_RTS		0x1c5
-			>;
-		};
-
-		pinctrl_uart2: uart2grp {
-			fsl,pins = <
-				MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX	0x1c5
-				MX53_PAD_PATA_DMARQ__UART2_TXD_MUX	0x1c5
-				MX53_PAD_PATA_DIOR__UART2_RTS		0x1c5
-				MX53_PAD_PATA_INTRQ__UART2_CTS		0x1c5
-			>;
-		};
-
-		pinctrl_uart3: uart3grp {
-			fsl,pins = <
-				MX53_PAD_PATA_CS_0__UART3_TXD_MUX	0x1e4
-				MX53_PAD_PATA_CS_1__UART3_RXD_MUX	0x1e4
-				MX53_PAD_PATA_DA_1__UART3_CTS		0x1e4
-				MX53_PAD_PATA_DA_2__UART3_RTS		0x1e4
-			>;
-		};
-
-		pinctrl_usbh1: usbh1grp {
-			fsl,pins = <
-				MX53_PAD_EIM_D30__GPIO3_30 0x100 /* OC */
-			>;
-		};
-
-		pinctrl_usbh1_vbus: usbh1-vbusgrp {
-			fsl,pins = <
-				MX53_PAD_EIM_D31__GPIO3_31 0xe0 /* VBUS ENABLE */
-			>;
-		};
-
-		pinctrl_usbotg_vbus: usbotg-vbusgrp {
-			fsl,pins = <
-				MX53_PAD_GPIO_7__GPIO1_7 0xe0 /* VBUS ENABLE */
-				MX53_PAD_GPIO_8__GPIO1_8 0x100 /* OC */
-			>;
-		};
-	};
-};
-
-&ipu {
-	status = "okay";
-};
-
-&nfc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_nand>;
-	nand-bus-width = <8>;
-	nand-ecc-mode = "hw";
-	nand-on-flash-bbt;
-	status = "okay";
-};
-
-&pwm2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm2>;
-};
-
-&sdma {
-	fsl,sdma-ram-script-name = "sdma-imx53.bin";
-};
-
-&ssi1 {
-	status = "okay";
-};
-
-&ssi2 {
-	status = "disabled";
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
-	uart-has-rtscts;
-	status = "okay";
-};
-
-&uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
-	uart-has-rtscts;
-	status = "okay";
-};
-
-&uart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart3>;
-	uart-has-rtscts;
-	status = "okay";
-};
-
-&usbh1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbh1>;
-	phy_type = "utmi";
-	disable-over-current;
-	vbus-supply = <&reg_usbh1_vbus>;
-	status = "okay";
-};
-
-&usbotg {
-	phy_type = "utmi";
-	dr_mode = "peripheral";
-	disable-over-current;
-	vbus-supply = <&reg_usbotg_vbus>;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6dl-aristainetos2_7.dts b/arch/arm/boot/dts/imx6dl-aristainetos2_7.dts
deleted file mode 100644
index 5e15212eaf3a..000000000000
--- a/arch/arm/boot/dts/imx6dl-aristainetos2_7.dts
+++ /dev/null
@@ -1,98 +0,0 @@
-/*
- * support for the imx6 based aristainetos2 board
- *
- * Copyright (C) 2015 Heiko Schocher <hs@denx.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-/dts-v1/;
-#include "imx6dl.dtsi"
-#include "imx6qdl-aristainetos2.dtsi"
-
-/ {
-	model = "aristainetos2 i.MX6 Dual Lite Board 7";
-	compatible = "abb,aristainetos2-imx6dl-7", "fsl,imx6dl";
-
-	memory@10000000 {
-		device_type = "memory";
-		reg = <0x10000000 0x40000000>;
-	};
-
-	panel: panel {
-		compatible = "lg,lb070wv8";
-		backlight = <&backlight>;
-		enable-gpios = <&gpio6 15 GPIO_ACTIVE_HIGH>;
-
-		port {
-			panel_in: endpoint {
-				remote-endpoint = <&lvds0_out>;
-			};
-		};
-	};
-};
-
-&i2c3 {
-	touch: touch@4d {
-		compatible = "atmel,maxtouch";
-		reg = <0x4d>;
-		interrupt-parent = <&gpio2>;
-		interrupts = <9 8>;
-	};
-};
-
-&ldb {
-	status = "okay";
-
-	lvds-channel@0 {
-		status = "okay";
-
-		port@0 {
-			reg = <0>;
-			lvds0_in: endpoint {
-				remote-endpoint = <&ipu1_di0_lvds0>;
-			};
-		};
-
-		port@4 {
-			reg = <4>;
-			lvds0_out: endpoint {
-				remote-endpoint = <&panel_in>;
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx6dl-colibri-v1_1-eval-v3.dts b/arch/arm/boot/dts/imx6dl-colibri-v1_1-eval-v3.dts
deleted file mode 100644
index 223275f028f1..000000000000
--- a/arch/arm/boot/dts/imx6dl-colibri-v1_1-eval-v3.dts
+++ /dev/null
@@ -1,31 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
-/*
- * Copyright 2020 Toradex
- */
-
-/dts-v1/;
-
-#include "imx6dl-colibri-eval-v3.dts"
-#include "imx6qdl-colibri-v1_1-uhs.dtsi"
-
-/ {
-	model = "Toradex Colibri iMX6DL/S V1.1 on Colibri Evaluation Board V3";
-	compatible = "toradex,colibri_imx6dl-v1_1-eval-v3",
-		     "toradex,colibri_imx6dl-v1_1",
-		     "toradex,colibri_imx6dl-eval-v3",
-		     "toradex,colibri_imx6dl",
-		     "fsl,imx6dl";
-};
-
-/* Colibri MMC */
-&usdhc1 {
-	status = "okay";
-	/*
-	 * Please make sure your carrier board does not pull-up any of
-	 * the MMC/SD signals to 3.3 volt before attempting to activate
-	 * UHS-I support.
-	 * To let signaling voltage be changed to 1.8V, please
-	 * delete no-1-8-v property (example below):
-	 * /delete-property/no-1-8-v;
-	 */
-};
diff --git a/arch/arm/boot/dts/imx6dl-gw551x.dts b/arch/arm/boot/dts/imx6dl-gw551x.dts
deleted file mode 100644
index 82d5f85722ea..000000000000
--- a/arch/arm/boot/dts/imx6dl-gw551x.dts
+++ /dev/null
@@ -1,55 +0,0 @@
-/*
- * Copyright 2014 Gateworks Corporation
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of
- *     the License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- *     You should have received a copy of the GNU General Public
- *     License along with this file; if not, write to the Free
- *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
- *     MA 02110-1301 USA
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6dl.dtsi"
-#include "imx6qdl-gw551x.dtsi"
-
-/ {
-	model = "Gateworks Ventana i.MX6 DualLite/Solo GW551X";
-	compatible = "gw,imx6dl-gw551x", "gw,ventana", "fsl,imx6dl";
-};
diff --git a/arch/arm/boot/dts/imx6dl-gw553x.dts b/arch/arm/boot/dts/imx6dl-gw553x.dts
deleted file mode 100644
index 59b8afc36e66..000000000000
--- a/arch/arm/boot/dts/imx6dl-gw553x.dts
+++ /dev/null
@@ -1,55 +0,0 @@
-/*
- * Copyright 2016 Gateworks Corporation
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of
- *     the License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- *     You should have received a copy of the GNU General Public
- *     License along with this file; if not, write to the Free
- *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
- *     MA 02110-1301 USA
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6dl.dtsi"
-#include "imx6qdl-gw553x.dtsi"
-
-/ {
-	model = "Gateworks Ventana i.MX6 DualLite/Solo GW553X";
-	compatible = "gw,imx6dl-gw553x", "gw,ventana", "fsl,imx6dl";
-};
diff --git a/arch/arm/boot/dts/imx6dl-gw560x.dts b/arch/arm/boot/dts/imx6dl-gw560x.dts
deleted file mode 100644
index 21bdfaf8df53..000000000000
--- a/arch/arm/boot/dts/imx6dl-gw560x.dts
+++ /dev/null
@@ -1,55 +0,0 @@
-/*
- * Copyright 2017 Gateworks Corporation
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of
- *     the License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- *     You should have received a copy of the GNU General Public
- *     License along with this file; if not, write to the Free
- *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
- *     MA 02110-1301 USA
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6dl.dtsi"
-#include "imx6qdl-gw560x.dtsi"
-
-/ {
-	model = "Gateworks Ventana i.MX6 DualLite/Solo GW560X";
-	compatible = "gw,imx6dl-gw560x", "gw,ventana", "fsl,imx6dl";
-};
diff --git a/arch/arm/boot/dts/imx6dl-gw5903.dts b/arch/arm/boot/dts/imx6dl-gw5903.dts
deleted file mode 100644
index 103261ea9334..000000000000
--- a/arch/arm/boot/dts/imx6dl-gw5903.dts
+++ /dev/null
@@ -1,55 +0,0 @@
-/*
- * Copyright 2017 Gateworks Corporation
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of
- *     the License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- *     You should have received a copy of the GNU General Public
- *     License along with this file; if not, write to the Free
- *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
- *     MA 02110-1301 USA
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6dl.dtsi"
-#include "imx6qdl-gw5903.dtsi"
-
-/ {
-	model = "Gateworks Ventana i.MX6 Duallite/Solo GW5903";
-	compatible = "gw,imx6dl-gw5903", "gw,ventana", "fsl,imx6dl";
-};
diff --git a/arch/arm/boot/dts/imx6dl-gw5904.dts b/arch/arm/boot/dts/imx6dl-gw5904.dts
deleted file mode 100644
index 9c6d3cd3d6a7..000000000000
--- a/arch/arm/boot/dts/imx6dl-gw5904.dts
+++ /dev/null
@@ -1,55 +0,0 @@
-/*
- * Copyright 2017 Gateworks Corporation
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of
- *     the License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- *     You should have received a copy of the GNU General Public
- *     License along with this file; if not, write to the Free
- *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
- *     MA 02110-1301 USA
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6dl.dtsi"
-#include "imx6qdl-gw5904.dtsi"
-
-/ {
-	model = "Gateworks Ventana i.MX6 DualLite/Solo GW5904";
-	compatible = "gw,imx6dl-gw5904", "gw,ventana", "fsl,imx6dl";
-};
diff --git a/arch/arm/boot/dts/imx6dl-tx6dl-comtft.dts b/arch/arm/boot/dts/imx6dl-tx6dl-comtft.dts
deleted file mode 100644
index 51a9bb9d6bc2..000000000000
--- a/arch/arm/boot/dts/imx6dl-tx6dl-comtft.dts
+++ /dev/null
@@ -1,79 +0,0 @@
-/*
- * Copyright 2014-2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6dl.dtsi"
-#include "imx6qdl-tx6.dtsi"
-#include "imx6qdl-tx6-lcd.dtsi"
-
-/ {
-	model = "Ka-Ro electronics TX6DL Module on CoMpact TFT";
-	compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
-};
-
-&backlight {
-	pwms = <&pwm2 0 500000 0>;
-	/delete-property/ turn-on-delay-ms;
-};
-
-&can1 {
-	status = "disabled";
-};
-
-&can2 {
-	xceiver-supply = <&reg_3v3>;
-};
-
-&kpp {
-	status = "disabled";
-};
-
-&lcd_panel {
-	compatible = "edt,etm0700g0edh6";
-};
-
-&reg_can_xcvr {
-	status = "disabled";
-};
-
-&touchscreen {
-	status = "disabled";
-};
diff --git a/arch/arm/boot/dts/imx6dl-tx6s-8034-mb7.dts b/arch/arm/boot/dts/imx6dl-tx6s-8034-mb7.dts
deleted file mode 100644
index fc23b4d291a1..000000000000
--- a/arch/arm/boot/dts/imx6dl-tx6s-8034-mb7.dts
+++ /dev/null
@@ -1,48 +0,0 @@
-/*
- * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6dl-tx6s-8034.dts"
-#include "imx6qdl-tx6-mb7.dtsi"
-
-/ {
-	model = "Ka-Ro electronics TX6S-8034 Module on MB7 baseboard";
-};
diff --git a/arch/arm/boot/dts/imx6dl-tx6s-8034.dts b/arch/arm/boot/dts/imx6dl-tx6s-8034.dts
deleted file mode 100644
index 9eb2ef17339c..000000000000
--- a/arch/arm/boot/dts/imx6dl-tx6s-8034.dts
+++ /dev/null
@@ -1,70 +0,0 @@
-/*
- * Copyright 2015-2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6dl.dtsi"
-#include "imx6qdl-tx6.dtsi"
-#include "imx6qdl-tx6-lcd.dtsi"
-
-/ {
-	model = "Ka-Ro electronics TX6S-8034 Module";
-	compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
-
-	cpus {
-		/delete-node/ cpu@1;
-	};
-};
-
-&ds1339 {
-	status = "disabled";
-};
-
-&pinctrl_usdhc1 {
-	fsl,pins = <
-		MX6QDL_PAD_SD1_CMD__SD1_CMD		0x070b1
-		MX6QDL_PAD_SD1_CLK__SD1_CLK		0x070b1
-		MX6QDL_PAD_SD1_DAT0__SD1_DATA0		0x070b1
-		MX6QDL_PAD_SD1_DAT1__SD1_DATA1		0x070b1
-		MX6QDL_PAD_SD1_DAT2__SD1_DATA2		0x070b1
-		MX6QDL_PAD_SD1_DAT3__SD1_DATA3		0x070b1
-		MX6QDL_PAD_SD3_CMD__GPIO7_IO02		0x170b0 /* SD1 CD */
-	>;
-};
diff --git a/arch/arm/boot/dts/imx6dl-tx6s-8035-mb7.dts b/arch/arm/boot/dts/imx6dl-tx6s-8035-mb7.dts
deleted file mode 100644
index 4101c6597721..000000000000
--- a/arch/arm/boot/dts/imx6dl-tx6s-8035-mb7.dts
+++ /dev/null
@@ -1,48 +0,0 @@
-/*
- * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6dl-tx6s-8035.dts"
-#include "imx6qdl-tx6-mb7.dtsi"
-
-/ {
-	model = "Ka-Ro electronics TX6U-8035 Module on MB7 baseboard";
-};
diff --git a/arch/arm/boot/dts/imx6dl-tx6s-8035.dts b/arch/arm/boot/dts/imx6dl-tx6s-8035.dts
deleted file mode 100644
index a5532ecc18c5..000000000000
--- a/arch/arm/boot/dts/imx6dl-tx6s-8035.dts
+++ /dev/null
@@ -1,86 +0,0 @@
-/*
- * Copyright 2015-2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6dl.dtsi"
-#include "imx6qdl-tx6.dtsi"
-#include "imx6qdl-tx6-lcd.dtsi"
-
-/ {
-	model = "Ka-Ro electronics TX6S-8035 Module";
-	compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
-
-	cpus {
-		/delete-node/ cpu@1;
-	};
-};
-
-&ds1339 {
-	status = "disabled";
-};
-
-&gpmi {
-	status = "disabled";
-};
-
-&usdhc4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc4>;
-	bus-width = <4>;
-	non-removable;
-	no-1-8-v;
-	fsl,wp-controller;
-	status = "okay";
-};
-
-&iomuxc {
-	pinctrl_usdhc4: usdhc4grp {
-		fsl,pins = <
-			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x070b1
-			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x070b1
-			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x070b1
-			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x070b1
-			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x070b1
-			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x070b1
-			MX6QDL_PAD_NANDF_ALE__SD4_RESET		0x0b0b1
-		>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-801x.dts b/arch/arm/boot/dts/imx6dl-tx6u-801x.dts
deleted file mode 100644
index 67ed0452f5de..000000000000
--- a/arch/arm/boot/dts/imx6dl-tx6u-801x.dts
+++ /dev/null
@@ -1,50 +0,0 @@
-/*
- * Copyright 2014-2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6dl.dtsi"
-#include "imx6qdl-tx6.dtsi"
-#include "imx6qdl-tx6-lcd.dtsi"
-
-/ {
-	model = "Ka-Ro electronics TX6U-801x Module";
-	compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
-};
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-8033-mb7.dts b/arch/arm/boot/dts/imx6dl-tx6u-8033-mb7.dts
deleted file mode 100644
index d34189fc52d9..000000000000
--- a/arch/arm/boot/dts/imx6dl-tx6u-8033-mb7.dts
+++ /dev/null
@@ -1,48 +0,0 @@
-/*
- * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6dl-tx6u-8033.dts"
-#include "imx6qdl-tx6-mb7.dtsi"
-
-/ {
-	model = "Ka-Ro electronics TX6U-8033 Module on MB7 baseboard";
-};
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-8033.dts b/arch/arm/boot/dts/imx6dl-tx6u-8033.dts
deleted file mode 100644
index 7030b2654bbd..000000000000
--- a/arch/arm/boot/dts/imx6dl-tx6u-8033.dts
+++ /dev/null
@@ -1,82 +0,0 @@
-/*
- * Copyright 2014-2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6dl.dtsi"
-#include "imx6qdl-tx6.dtsi"
-#include "imx6qdl-tx6-lcd.dtsi"
-
-/ {
-	model = "Ka-Ro electronics TX6U-8033 Module";
-	compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
-};
-
-&ds1339 {
-	status = "disabled";
-};
-
-&gpmi {
-	status = "disabled";
-};
-
-&usdhc4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc4>;
-	bus-width = <4>;
-	non-removable;
-	no-1-8-v;
-	fsl,wp-controller;
-	status = "okay";
-};
-
-&iomuxc {
-	pinctrl_usdhc4: usdhc4grp {
-		fsl,pins = <
-			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x070b1
-			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x070b1
-			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x070b1
-			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x070b1
-			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x070b1
-			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x070b1
-			MX6QDL_PAD_NANDF_ALE__SD4_RESET		0x0b0b1
-		>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-80xx-mb7.dts b/arch/arm/boot/dts/imx6dl-tx6u-80xx-mb7.dts
deleted file mode 100644
index aef5fcc42904..000000000000
--- a/arch/arm/boot/dts/imx6dl-tx6u-80xx-mb7.dts
+++ /dev/null
@@ -1,48 +0,0 @@
-/*
- * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6dl-tx6u-801x.dts"
-#include "imx6qdl-tx6-mb7.dtsi"
-
-/ {
-	model = "Ka-Ro electronics TX6U-8030/-8010/-8012 Module on MB7 baseboard";
-};
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-811x.dts b/arch/arm/boot/dts/imx6dl-tx6u-811x.dts
deleted file mode 100644
index 5342f2f5a8a8..000000000000
--- a/arch/arm/boot/dts/imx6dl-tx6u-811x.dts
+++ /dev/null
@@ -1,50 +0,0 @@
-/*
- * Copyright 2014-2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6dl.dtsi"
-#include "imx6qdl-tx6.dtsi"
-#include "imx6qdl-tx6-lvds.dtsi"
-
-/ {
-	model = "Ka-Ro electronics TX6U-811x Module";
-	compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
-};
diff --git a/arch/arm/boot/dts/imx6dl-tx6u-81xx-mb7.dts b/arch/arm/boot/dts/imx6dl-tx6u-81xx-mb7.dts
deleted file mode 100644
index c4588fb0bf6f..000000000000
--- a/arch/arm/boot/dts/imx6dl-tx6u-81xx-mb7.dts
+++ /dev/null
@@ -1,48 +0,0 @@
-/*
- * Copyright 2016-2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6dl-tx6u-811x.dts"
-#include "imx6qdl-tx6-mb7.dtsi"
-
-/ {
-	model = "Ka-Ro electronics TX6U-8130/-8110 Module on MB7 baseboard";
-};
diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
deleted file mode 100644
index 227c952543d4..000000000000
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ /dev/null
@@ -1,943 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-/*
- * Copyright (c) 2016 Protonic Holland
- * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
- */
-
-/dts-v1/;
-#include <dt-bindings/display/sdtv-standards.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/media/tvp5150.h>
-#include <dt-bindings/sound/fsl-imx-audmux.h>
-#include "imx6dl.dtsi"
-
-/ {
-	model = "Kverneland TGO";
-	compatible = "kvg,victgo", "fsl,imx6dl";
-
-	chosen {
-		stdout-path = &uart4;
-	};
-
-	backlight: backlight {
-		compatible = "pwm-backlight";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_backlight>;
-		pwms = <&pwm1 0 5000000 0>;
-		brightness-levels = <0 16 64 255>;
-		num-interpolated-steps = <16>;
-		default-brightness-level = <1>;
-		power-supply = <&reg_3v3>;
-		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
-	};
-
-	connector {
-		compatible = "composite-video-connector";
-		label = "Composite0";
-		sdtv-standards = <SDTV_STD_PAL_B>;
-
-		port {
-			comp0_out: endpoint {
-				remote-endpoint = <&tvp5150_comp0_in>;
-			};
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpiokeys>;
-		autorepeat;
-
-		power {
-			label = "Power Button";
-			gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_POWER>;
-			wakeup-source;
-		};
-
-		enter {
-			label = "Rotary Key";
-			gpios = <&gpio2 05 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_ENTER>;
-			wakeup-source;
-		};
-	};
-
-	iio-hwmon {
-		compatible = "iio-hwmon";
-		io-channels = <&vdiv_vaccu>, <&vdiv_hitch_pos>;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_leds>;
-
-		led-0 {
-			label = "debug0";
-			function = LED_FUNCTION_HEARTBEAT;
-			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-		};
-
-		led-1 {
-			label = "debug1";
-			function = LED_FUNCTION_DISK;
-			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "disk-activity";
-		};
-
-		led-2 {
-			label = "power_led";
-			function = LED_FUNCTION_POWER;
-			gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
-			default-state = "on";
-		};
-	};
-
-	panel {
-		compatible = "kyo,tcg121xglp";
-		backlight = <&backlight>;
-		power-supply = <&reg_3v3>;
-
-		port {
-			panel_in: endpoint {
-				remote-endpoint = <&lvds0_out>;
-			};
-		};
-	};
-
-	clk50m_phy: phy-clock {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <50000000>;
-	};
-
-	reg_1v8: regulator-1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "1v8";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-	};
-
-	reg_3v3: regulator-3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	reg_h1_vbus: regulator-h1-vbus {
-		compatible = "regulator-fixed";
-		regulator-name = "h1-vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	reg_otg_vbus: regulator-otg-vbus {
-		compatible = "regulator-fixed";
-		regulator-name = "otg-vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	rotary-encoder {
-		compatible = "rotary-encoder";
-		pinctrl-0 = <&pinctrl_rotary_ch>;
-		gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>,
-			<&gpio2 4 GPIO_ACTIVE_HIGH>;
-		linux,axis = <REL_WHEEL>;
-		rotary-encoder,steps-per-period = <4>;
-		rotary-encoder,relative-axis;
-		rotary-encoder,rollover;
-		wakeup-source;
-	};
-
-	sound {
-		compatible = "simple-audio-card";
-		simple-audio-card,name = "prti6q-sgtl5000";
-		simple-audio-card,format = "i2s";
-		simple-audio-card,widgets =
-			"Microphone", "Microphone Jack",
-			"Line", "Line In Jack",
-			"Headphone", "Headphone Jack",
-			"Speaker", "External Speaker";
-		simple-audio-card,routing =
-			"MIC_IN", "Microphone Jack",
-			"LINE_IN", "Line In Jack",
-			"Headphone Jack", "HP_OUT",
-			"External Speaker", "LINE_OUT";
-
-		simple-audio-card,cpu {
-			sound-dai = <&ssi1>;
-			system-clock-frequency = <0>;
-		};
-
-		simple-audio-card,codec {
-			sound-dai = <&codec>;
-			bitclock-master;
-			frame-master;
-		};
-	};
-
-	thermal-zones {
-		chassis-thermal {
-			polling-delay = <20000>;
-			polling-delay-passive = <0>;
-			thermal-sensors = <&tsens0>;
-		};
-
-		touch-thermal0 {
-			polling-delay = <20000>;
-			polling-delay-passive = <0>;
-			thermal-sensors = <&touch_temp0>;
-		};
-
-		touch-thermal1 {
-			polling-delay = <20000>;
-			polling-delay-passive = <0>;
-			thermal-sensors = <&touch_temp1>;
-		};
-	};
-
-	touchscreen {
-		compatible = "resistive-adc-touch";
-		io-channels = <&adc_ts 1>, <&adc_ts 3>, <&adc_ts 4>,
-                              <&adc_ts 5>;
-		io-channel-names = "y", "z1", "z2", "x";
-		touchscreen-min-pressure = <64687>;
-		touchscreen-inverted-x;
-		touchscreen-inverted-y;
-		touchscreen-x-plate-ohms = <300>;
-		touchscreen-y-plate-ohms = <800>;
-	};
-
-	touch_temp0: touch-temperature-sensor0 {
-		compatible = "generic-adc-thermal";
-		#thermal-sensor-cells = <0>;
-		io-channels = <&adc_ts 0>;
-		io-channel-names = "sensor-channel";
-		temperature-lookup-table = <    (-40000) 736
-						85000 474>;
-	};
-
-	touch_temp1: touch-temperature-sensor1 {
-		compatible = "generic-adc-thermal";
-		#thermal-sensor-cells = <0>;
-		io-channels = <&adc_ts 7>;
-		io-channel-names = "sensor-channel";
-		temperature-lookup-table = <    (-40000) 826
-						85000 609>;
-	};
-
-	vdiv_vaccu: voltage-divider-vaccu {
-		compatible = "voltage-divider";
-		io-channels = <&adc_ts 2>;
-		output-ohms = <2500>;
-		full-ohms = <64000>;
-		#io-channel-cells = <0>;
-	};
-
-	vdiv_hitch_pos: voltage-divider-hitch-pos {
-		compatible = "voltage-divider";
-		io-channels = <&adc_ts 6>;
-		output-ohms = <3300>;
-		full-ohms = <13300>;
-		#io-channel-cells = <0>;
-	};
-};
-
-&audmux {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_audmux>;
-	status = "okay";
-
-	mux-ssi1 {
-		fsl,audmux-port = <0>;
-		fsl,port-config = <
-			IMX_AUDMUX_V2_PTCR_SYN		0
-			IMX_AUDMUX_V2_PTCR_TFSEL(2)	0
-			IMX_AUDMUX_V2_PTCR_TCSEL(2)	0
-			IMX_AUDMUX_V2_PTCR_TFSDIR	0
-			IMX_AUDMUX_V2_PTCR_TCLKDIR	IMX_AUDMUX_V2_PDCR_RXDSEL(2)
-		>;
-	};
-
-	mux-pins3 {
-		fsl,audmux-port = <2>;
-		fsl,port-config = <
-			IMX_AUDMUX_V2_PTCR_SYN		IMX_AUDMUX_V2_PDCR_RXDSEL(0)
-			0				IMX_AUDMUX_V2_PDCR_TXRXEN
-		>;
-	};
-};
-
-&can1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_can1>;
-	status = "okay";
-};
-
-&can2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_can2>;
-	status = "okay";
-};
-
-&clks {
-	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
-	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
-};
-
-&ecspi1 {
-	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi1>;
-	status = "okay";
-
-	flash@0 {
-		compatible = "jedec,spi-nor";
-		reg = <0>;
-		spi-max-frequency = <20000000>;
-	};
-};
-
-&ecspi2 {
-	cs-gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi2>;
-	status = "okay";
-
-	adc_ts: adc@0 {
-		compatible = "ti,tsc2046e-adc";
-		reg = <0>;
-		pinctrl-0 = <&pinctrl_touchscreen>;
-		pinctrl-names ="default";
-		spi-max-frequency = <1000000>;
-		interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;
-		#io-channel-cells = <1>;
-
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		channel@1 {
-			reg = <1>;
-			settling-time-us = <700>;
-			oversampling-ratio = <5>;
-		};
-
-		channel@3 {
-			reg = <3>;
-			settling-time-us = <700>;
-			oversampling-ratio = <5>;
-		};
-
-		channel@4 {
-			reg = <4>;
-			settling-time-us = <700>;
-			oversampling-ratio = <5>;
-		};
-
-		channel@5 {
-			reg = <5>;
-			settling-time-us = <700>;
-			oversampling-ratio = <5>;
-		};
-	};
-};
-
-&fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rmii";
-	clocks = <&clks IMX6QDL_CLK_ENET>,
-		 <&clks IMX6QDL_CLK_ENET>,
-		 <&clk50m_phy>;
-	clock-names = "ipg", "ahb", "ptp";
-	phy-handle = <&rmii_phy>;
-	status = "okay";
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		/* Microchip KSZ8081RNA PHY */
-		rmii_phy: ethernet-phy@0 {
-			reg = <0>;
-			interrupts-extended = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>;
-			reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
-			reset-assert-us = <10000>;
-			reset-deassert-us = <300>;
-		};
-	};
-};
-
-&gpio1 {
-	gpio-line-names =
-		"CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
-			"CAM2_MIRROR", "", "", "SMBALERT",
-		"DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
-		"SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
-			"SD1_DATA3", "", "",
-		"", "", "", "", "", "", "", "";
-};
-
-&gpio2 {
-	gpio-line-names =
-		"", "", "", "", "", "", "", "",
-		"REV_ID0", "REV_ID1", "REV_ID2", "REV_ID3", "REV_ID4",
-			"BOARD_ID0", "BOARD_ID1", "BOARD_ID2",
-		"", "", "", "", "", "", "ISB_IN1", "ON_SWITCH",
-		"POWER_LED", "", "", "", "", "", "", "";
-};
-
-&gpio3 {
-	gpio-line-names =
-		"", "", "", "", "", "", "", "",
-		"", "", "", "", "", "", "", "",
-		"ECSPI1_SCLK", "ECSPI1_MISO", "ECSPI1_MOSI", "ECSPI1_SS1",
-			"CPU_ON1_FB", "USB_EXT1_OC", "USB_EXT1_PWR", "YACO_IRQ",
-		"TSS_TXD", "TSS_RXD", "", "", "", "", "YACO_BOOT0",
-			"YACO_RESET";
-};
-
-&gpio4 {
-	gpio-line-names =
-		"", "", "", "", "", "", "", "",
-		"", "", "", "", "CAN1_SR", "CAN2_SR", "CAN2_TX", "CAN2_RX",
-		"", "", "DIP1_FB", "", "VCAM_EN", "", "", "",
-		"CPU_LIGHT_ON", "", "ETH_RESET", "CPU_CONTACT_IN", "BL_EN",
-			"BL_PWM", "ETH_INTRP", "ISB_LED";
-};
-
-&gpio5 {
-	gpio-line-names =
-		"", "", "", "", "", "", "", "",
-		"TSC_PENIRQ", "TSC_BUSY", "ECSPI2_MOSI", "ECSPI2_MISO",
-			"ECSPI2_SS0", "ECSPI2_SCLK", "", "",
-		"", "", "", "", "", "", "", "",
-		"I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
-			"YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
-};
-
-&i2c1 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c1>;
-	status = "okay";
-
-	codec: audio-codec@a {
-		compatible = "fsl,sgtl5000";
-		reg = <0xa>;
-		#sound-dai-cells = <0>;
-		clocks = <&clks 201>;
-		VDDA-supply = <&reg_3v3>;
-		VDDIO-supply = <&reg_3v3>;
-		VDDD-supply = <&reg_1v8>;
-	};
-
-	video-decoder@5c {
-		compatible = "ti,tvp5150";
-		reg = <0x5c>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		port@0 {
-			reg = <0>;
-
-			tvp5150_comp0_in: endpoint {
-				remote-endpoint = <&comp0_out>;
-			};
-		};
-
-		/* Output port 2 is video output pad */
-		port@2 {
-			reg = <2>;
-
-			tvp5151_to_ipu1_csi0_mux: endpoint {
-				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
-			};
-		};
-	};
-
-	keypad@70 {
-		compatible = "holtek,ht16k33";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_keypad>;
-		reg = <0x70>;
-		refresh-rate-hz = <20>;
-		debounce-delay-ms = <50>;
-		interrupts-extended = <&gpio4 5 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>;
-		keypad,num-rows = <12>;
-		keypad,num-columns = <3>;
-		linux,keymap = <
-			MATRIX_KEY(2, 0, KEY_F6)
-			MATRIX_KEY(3, 0, KEY_F8)
-			MATRIX_KEY(4, 0, KEY_F10)
-			MATRIX_KEY(5, 0, KEY_F4)
-			MATRIX_KEY(6, 0, KEY_F2)
-			MATRIX_KEY(2, 1, KEY_F5)
-			MATRIX_KEY(3, 1, KEY_F7)
-			MATRIX_KEY(4, 1, KEY_F9)
-			MATRIX_KEY(5, 1, KEY_F3)
-			MATRIX_KEY(6, 1, KEY_F1)
-		      >;
-	};
-
-	/* additional i2c devices are added automatically by the boot loader */
-};
-
-&i2c3 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c3>;
-	status = "okay";
-
-	adc@49 {
-		compatible = "ti,ads1015";
-		reg = <0x49>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		channel@4 {
-			reg = <4>;
-			ti,gain = <3>;
-			ti,datarate = <3>;
-		};
-
-		channel@5 {
-			reg = <5>;
-			ti,gain = <3>;
-			ti,datarate = <3>;
-		};
-
-		channel@6 {
-			reg = <6>;
-			ti,gain = <3>;
-			ti,datarate = <3>;
-		};
-
-		channel@7 {
-			reg = <7>;
-			ti,gain = <3>;
-			ti,datarate = <3>;
-		};
-	};
-
-	rtc@51 {
-		compatible = "nxp,pcf8563";
-		reg = <0x51>;
-	};
-
-	tsens0: temperature-sensor@70 {
-		compatible = "ti,tmp103";
-		reg = <0x70>;
-		#thermal-sensor-cells = <0>;
-	};
-};
-
-&ipu1_csi0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ipu1_csi0>;
-	status = "okay";
-};
-
-&ipu1_csi0_mux_from_parallel_sensor {
-	remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>;
-};
-
-&ldb {
-	status = "okay";
-
-	lvds-channel@0 {
-		status = "okay";
-
-		port@4 {
-			reg = <4>;
-
-			lvds0_out: endpoint {
-				remote-endpoint = <&panel_in>;
-			};
-		};
-	};
-};
-
-&pwm1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm1>;
-	status = "okay";
-};
-
-&pwm3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm3>;
-	status = "okay";
-};
-
-&ssi1 {
-	#sound-dai-cells = <0>;
-	fsl,mode = "ac97-slave";
-	status = "okay";
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
-	status = "okay";
-};
-
-&uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
-	status = "okay";
-};
-
-&uart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart3>;
-	status = "okay";
-};
-
-&uart4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart4>;
-	status = "okay";
-};
-
-&uart5 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart5>;
-	status = "okay";
-};
-
-&usbh1 {
-	vbus-supply = <&reg_h1_vbus>;
-	pinctrl-names = "default";
-	phy_type = "utmi";
-	dr_mode = "host";
-	status = "okay";
-};
-
-&usbotg {
-	vbus-supply = <&reg_otg_vbus>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbotg>;
-	phy_type = "utmi";
-	dr_mode = "host";
-	disable-over-current;
-	status = "okay";
-};
-
-&usdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc1>;
-	cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
-	no-1-8-v;
-	disable-wp;
-	cap-sd-highspeed;
-	no-mmc;
-	no-sdio;
-	status = "okay";
-};
-
-&usdhc3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc3>;
-	bus-width = <8>;
-	no-1-8-v;
-	non-removable;
-	no-sd;
-	no-sdio;
-	status = "okay";
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_hog>;
-
-	pinctrl_audmux: audmuxgrp {
-		fsl,pins = <
-			/* SGTL5000 sys_mclk */
-			MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1			0x030b0
-			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD			0x130b0
-			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC			0x130b0
-			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD			0x110b0
-			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS			0x130b0
-		>;
-	};
-
-	pinctrl_backlight: backlightgrp {
-		fsl,pins = <
-			MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28		0x1b0b0
-		>;
-	};
-
-	pinctrl_can1: can1grp {
-		fsl,pins = <
-			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX		0x1b000
-			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX		0x3008
-			/* CAN1_SR */
-			MX6QDL_PAD_KEY_COL3__GPIO4_IO12			0x13008
-			/* CAN1_TERM */
-			MX6QDL_PAD_GPIO_0__GPIO1_IO00			0x1b088
-		>;
-	};
-
-	pinctrl_can2: can2grp {
-		fsl,pins = <
-			MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX		0x1b000
-			MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX		0x3008
-			/* CAN2_SR */
-			MX6QDL_PAD_KEY_ROW3__GPIO4_IO13			0x13008
-		>;
-	};
-
-	pinctrl_ecspi1: ecspi1grp {
-		fsl,pins = <
-			MX6QDL_PAD_EIM_D17__ECSPI1_MISO			0x100b1
-			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI			0x100b1
-			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK			0x100b1
-			/* CS */
-			MX6QDL_PAD_EIM_D19__GPIO3_IO19			0x000b1
-		>;
-	};
-
-	pinctrl_ecspi2: ecspi2grp {
-		fsl,pins = <
-			MX6QDL_PAD_DISP0_DAT16__ECSPI2_MOSI		0x100b1
-			MX6QDL_PAD_DISP0_DAT17__ECSPI2_MISO		0x100b1
-			MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12		0x100b1
-			MX6QDL_PAD_DISP0_DAT19__ECSPI2_SCLK		0x100b1
-		>;
-	};
-
-	pinctrl_enet: enetgrp {
-		fsl,pins = <
-			/* MX6QDL_ENET_PINGRP4 */
-			MX6QDL_PAD_ENET_MDC__ENET_MDC			0x1b0b0
-			MX6QDL_PAD_ENET_MDIO__ENET_MDIO			0x1b0b0
-			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0		0x1b0b0
-			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1		0x1b0b0
-			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER		0x1b0b0
-			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN		0x1b0b0
-			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0		0x1b0b0
-			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1		0x1b0b0
-			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN		0x1b0b0
-			MX6QDL_PAD_GPIO_16__ENET_REF_CLK		0x1b0b0
-			/* Phy reset */
-			MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26		0x1b0b0
-			/* nINTRP */
-			MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30		0x1b0b0
-		>;
-	};
-
-	pinctrl_gpiokeys: gpiokeygrp {
-		fsl,pins = <
-			/* ROTARY_BTN */
-			MX6QDL_PAD_NANDF_D5__GPIO2_IO05			0x1b0b0
-			/* nON_SWITCH */
-			MX6QDL_PAD_EIM_CS0__GPIO2_IO23			0x1b0b0
-		>;
-	};
-
-	pinctrl_hog: hoggrp {
-		fsl,pins = <
-			/* ITU656_nRESET */
-			MX6QDL_PAD_GPIO_2__GPIO1_IO02			0x1b0b0
-			/* CAM1_MIRROR */
-			MX6QDL_PAD_GPIO_3__GPIO1_IO03			0x130b0
-			/* CAM2_MIRROR */
-			MX6QDL_PAD_GPIO_4__GPIO1_IO04			0x130b0
-			/* CAM_nDETECT */
-			MX6QDL_PAD_GPIO_17__GPIO7_IO12			0x1b0b0
-			/* ISB_IN1 */
-			MX6QDL_PAD_EIM_A16__GPIO2_IO22			0x130b0
-			/* ISB_nIN2 */
-			MX6QDL_PAD_EIM_A17__GPIO2_IO21			0x1b0b0
-			/* WARN_LIGHT */
-			MX6QDL_PAD_EIM_A19__GPIO2_IO19			0x100b0
-			/* ON2_FB */
-			MX6QDL_PAD_EIM_A25__GPIO5_IO02			0x100b0
-			/* YACO_nIRQ */
-			MX6QDL_PAD_EIM_D23__GPIO3_IO23			0x1b0b0
-			/* YACO_BOOT0 */
-			MX6QDL_PAD_EIM_D30__GPIO3_IO30			0x130b0
-			/* YACO_nRESET */
-			MX6QDL_PAD_EIM_D31__GPIO3_IO31			0x1b0b0
-			/* FORCE_ON1 */
-			MX6QDL_PAD_EIM_EB2__GPIO2_IO30			0x1b0b0
-			/* AUDIO_nRESET */
-			MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21		0x1f0b0
-			/* ITU656_nPDN */
-			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20		0x1b0b0
-
-			/* HW revision detect */
-			/* REV_ID0 */
-			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08			0x1b0b0
-			/* REV_ID1 is shared with PWM3 */
-			/* REV_ID2 */
-			MX6QDL_PAD_SD4_DAT2__GPIO2_IO10			0x1b0b0
-			/* REV_ID3 */
-			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11			0x1b0b0
-			/* REV_ID4 */
-			MX6QDL_PAD_SD4_DAT4__GPIO2_IO12			0x1b0b0
-
-			/* New in HW revision 1 */
-			/* ON1_FB */
-			MX6QDL_PAD_EIM_D20__GPIO3_IO20			0x100b0
-			/* DIP1_FB */
-			MX6QDL_PAD_DI0_PIN2__GPIO4_IO18			0x1b0b0
-		>;
-	};
-
-	pinctrl_i2c1: i2c1grp {
-		fsl,pins = <
-			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA		0x4001f8b1
-			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL		0x4001f8b1
-		>;
-	};
-
-	pinctrl_i2c3: i2c3grp {
-		fsl,pins = <
-			MX6QDL_PAD_GPIO_5__I2C3_SCL		0x4001b8b1
-			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
-		>;
-	};
-
-	pinctrl_ipu1_csi0: ipu1csi0grp {
-		fsl,pins = <
-			MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12		0x1b0b0
-			MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13		0x1b0b0
-			MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14		0x1b0b0
-			MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15		0x1b0b0
-			MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16		0x1b0b0
-			MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17		0x1b0b0
-			MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18		0x1b0b0
-			MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19		0x1b0b0
-			MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK	0x1b0b0
-		>;
-	};
-
-	pinctrl_keypad: keypadgrp {
-		fsl,pins = <
-			MX6QDL_PAD_GPIO_19__GPIO4_IO05			0x1b0b0
-		>;
-	};
-
-	pinctrl_leds: ledsgrp {
-		fsl,pins = <
-			/* DEBUG0 */
-			MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16		0x1b0b0
-			/* DEBUG1 */
-			MX6QDL_PAD_DI0_PIN15__GPIO4_IO17		0x1b0b0
-			/* POWER_LED */
-			MX6QDL_PAD_EIM_CS1__GPIO2_IO24			0x1b0b0
-		>;
-	};
-
-	pinctrl_pwm1: pwm1grp {
-		fsl,pins = <
-			MX6QDL_PAD_DISP0_DAT8__PWM1_OUT			0x1b0b0
-		>;
-	};
-
-	pinctrl_pwm3: pwm3grp {
-		fsl,pins = <
-			MX6QDL_PAD_SD4_DAT1__PWM3_OUT			0x1b0b0
-		>;
-	};
-
-	pinctrl_rotary_ch: rotarychgrp {
-		fsl,pins = <
-			MX6QDL_PAD_NANDF_D3__GPIO2_IO03			0x1b0b0
-			MX6QDL_PAD_NANDF_D4__GPIO2_IO04			0x1b0b0
-		>;
-	};
-
-	pinctrl_touchscreen: touchscreengrp {
-		fsl,pins = <
-			MX6QDL_PAD_DISP0_DAT14__GPIO5_IO08		0x1b0b0
-			MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09		0x1b0b0
-		>;
-	};
-
-	/* YaCO AUX Uart */
-	pinctrl_uart1: uart1grp {
-		fsl,pins = <
-			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA		0x1b0b1
-			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA		0x1b0b1
-		>;
-	};
-
-	pinctrl_uart2: uart2grp {
-		fsl,pins = <
-			MX6QDL_PAD_EIM_D26__UART2_TX_DATA		0x1b0b1
-			MX6QDL_PAD_EIM_D27__UART2_RX_DATA		0x1b0b1
-		>;
-	};
-
-	/* YaCO Touchscreen UART */
-	pinctrl_uart3: uart3grp {
-		fsl,pins = <
-			MX6QDL_PAD_EIM_D24__UART3_TX_DATA		0x1b0b1
-			MX6QDL_PAD_EIM_D25__UART3_RX_DATA		0x1b0b1
-		>;
-	};
-
-	pinctrl_uart4: uart4grp {
-		fsl,pins = <
-			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA		0x1b0b1
-			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA		0x1b0b1
-		>;
-	};
-
-	pinctrl_uart5: uart5grp {
-		fsl,pins = <
-			MX6QDL_PAD_KEY_COL1__UART5_TX_DATA		0x1b0b1
-			MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA		0x1b0b1
-		>;
-	};
-
-	pinctrl_usbotg: usbotggrp {
-		fsl,pins = <
-			MX6QDL_PAD_EIM_D21__USB_OTG_OC			0x1b0b0
-			/* power enable, high active */
-			MX6QDL_PAD_EIM_D22__GPIO3_IO22			0x1b0b0
-		>;
-	};
-
-	pinctrl_usdhc1: usdhc1grp {
-		fsl,pins = <
-			MX6QDL_PAD_SD1_CMD__SD1_CMD			0x170f9
-			MX6QDL_PAD_SD1_CLK__SD1_CLK			0x100f9
-			MX6QDL_PAD_SD1_DAT0__SD1_DATA0			0x170f9
-			MX6QDL_PAD_SD1_DAT1__SD1_DATA1			0x170f9
-			MX6QDL_PAD_SD1_DAT2__SD1_DATA2			0x170f9
-			MX6QDL_PAD_SD1_DAT3__SD1_DATA3			0x170f9
-			MX6QDL_PAD_GPIO_1__GPIO1_IO01			0x1b0b0
-		>;
-	};
-
-	pinctrl_usdhc3: usdhc3grp {
-		fsl,pins = <
-			MX6QDL_PAD_SD3_CMD__SD3_CMD			0x17099
-			MX6QDL_PAD_SD3_CLK__SD3_CLK			0x10099
-			MX6QDL_PAD_SD3_DAT0__SD3_DATA0			0x17099
-			MX6QDL_PAD_SD3_DAT1__SD3_DATA1			0x17099
-			MX6QDL_PAD_SD3_DAT2__SD3_DATA2			0x17099
-			MX6QDL_PAD_SD3_DAT3__SD3_DATA3			0x17099
-			MX6QDL_PAD_SD3_DAT4__SD3_DATA4			0x17099
-			MX6QDL_PAD_SD3_DAT5__SD3_DATA5			0x17099
-			MX6QDL_PAD_SD3_DAT6__SD3_DATA6			0x17099
-			MX6QDL_PAD_SD3_DAT7__SD3_DATA7			0x17099
-			MX6QDL_PAD_SD3_RST__SD3_RESET			0x1b0b1
-		>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx6q-apalis-eval.dts b/arch/arm/boot/dts/imx6q-apalis-eval.dts
deleted file mode 100644
index a0683b4aeca1..000000000000
--- a/arch/arm/boot/dts/imx6q-apalis-eval.dts
+++ /dev/null
@@ -1,273 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
-/*
- * Copyright 2014-2020 Toradex
- * Copyright 2012 Freescale Semiconductor, Inc.
- * Copyright 2011 Linaro Ltd.
- */
-
-/dts-v1/;
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include "imx6q.dtsi"
-#include "imx6qdl-apalis.dtsi"
-
-/ {
-	model = "Toradex Apalis iMX6Q/D Module on Apalis Evaluation Board";
-	compatible = "toradex,apalis_imx6q-eval", "toradex,apalis_imx6q",
-		     "fsl,imx6q";
-
-	aliases {
-		i2c0 = &i2c1;
-		i2c1 = &i2c3;
-		i2c2 = &i2c2;
-		rtc0 = &rtc_i2c;
-		rtc1 = &snvs_rtc;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpio_keys>;
-
-		wakeup {
-			label = "Wake-Up";
-			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_WAKEUP>;
-			debounce-interval = <10>;
-			wakeup-source;
-		};
-	};
-
-	lcd_display: disp0 {
-		compatible = "fsl,imx-parallel-display";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		interface-pix-fmt = "rgb24";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_ipu1_lcdif>;
-		status = "okay";
-
-		port@0 {
-			reg = <0>;
-
-			lcd_display_in: endpoint {
-				remote-endpoint = <&ipu1_di1_disp1>;
-			};
-		};
-
-		port@1 {
-			reg = <1>;
-
-			lcd_display_out: endpoint {
-				remote-endpoint = <&lcd_panel_in>;
-			};
-		};
-	};
-
-	panel: panel {
-		/*
-		 * edt,et057090dhu: EDT 5.7" LCD TFT
-		 * edt,et070080dh6: EDT 7.0" LCD TFT
-		 */
-		compatible = "edt,et057090dhu";
-		backlight = <&backlight>;
-		power-supply = <&reg_3v3_sw>;
-
-		port {
-			lcd_panel_in: endpoint {
-				remote-endpoint = <&lcd_display_out>;
-			};
-		};
-	};
-
-	reg_pcie_switch: regulator-pcie-switch {
-		compatible = "regulator-fixed";
-		regulator-name = "pcie_switch";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
-		startup-delay-us = <100000>;
-		enable-active-high;
-		status = "okay";
-	};
-
-	reg_3v3_sw: regulator-3v3-sw {
-		compatible = "regulator-fixed";
-		regulator-name = "3.3V_SW";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-};
-
-&backlight {
-	brightness-levels = <0 127 191 223 239 247 251 255>;
-	default-brightness-level = <1>;
-	power-supply = <&reg_3v3_sw>;
-	status = "okay";
-};
-
-&can1 {
-	xceiver-supply = <&reg_3v3_sw>;
-	status = "okay";
-};
-
-&can2 {
-	xceiver-supply = <&reg_3v3_sw>;
-	status = "okay";
-};
-
-&hdmi {
-	status = "okay";
-};
-
-/* I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier board) */
-&i2c1 {
-	status = "okay";
-
-	/*
-	 * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
-	 * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
-	 */
-	touchscreen@4a {
-		compatible = "atmel,maxtouch";
-		reg = <0x4a>;
-		interrupt-parent = <&gpio6>;
-		interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
-		reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>; /* SODIMM 13 */
-		status = "disabled";
-	};
-
-	pcie-switch@58 {
-		compatible = "plx,pex8605";
-		reg = <0x58>;
-	};
-
-	/* M41T0M6 real time clock on carrier board */
-	rtc_i2c: rtc@68 {
-		compatible = "st,m41t0";
-		reg = <0x68>;
-	};
-};
-
-/*
- * I2C3_SDA/SCL (CAM) on MXM3 pin 201/203 (e.g. camera sensor on carrier
- * board)
- */
-&i2c3 {
-	status = "okay";
-};
-
-&ipu1_di1_disp1 {
-	remote-endpoint = <&lcd_display_in>;
-};
-
-&ldb {
-	status = "okay";
-};
-
-&pcie {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_reset_moci>;
-	/* active-high meaning opposite of regular PERST# active-low polarity */
-	reset-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
-	reset-gpio-active-high;
-	vpcie-supply = <&reg_pcie_switch>;
-	status = "okay";
-};
-
-&pwm1 {
-	status = "okay";
-};
-
-&pwm2 {
-	status = "okay";
-};
-
-&pwm3 {
-	status = "okay";
-};
-
-&pwm4 {
-	status = "okay";
-};
-
-&reg_usb_otg_vbus {
-	status = "okay";
-};
-
-&reg_usb_host_vbus {
-	status = "okay";
-};
-
-&sata {
-	status = "okay";
-};
-
-&sound_spdif {
-	status = "okay";
-};
-
-&spdif {
-	status = "okay";
-};
-
-&uart1 {
-	status = "okay";
-};
-
-&uart2 {
-	status = "okay";
-};
-
-&uart4 {
-	status = "okay";
-};
-
-&uart5 {
-	status = "okay";
-};
-
-&usbh1 {
-	vbus-supply = <&reg_usb_host_vbus>;
-	status = "okay";
-};
-
-&usbotg {
-	vbus-supply = <&reg_usb_otg_vbus>;
-	status = "okay";
-};
-
-/* MMC1 */
-&usdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc1_4bit &pinctrl_usdhc1_8bit &pinctrl_mmc_cd>;
-	cd-gpios = <&gpio4 20 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-/* SD1 */
-&usdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc2 &pinctrl_sd_cd>;
-	cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-&iomuxc {
-	/*
-	 * Mux the Apalis GPIOs
-	 */
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_apalis_gpio1 &pinctrl_apalis_gpio2
-		     &pinctrl_apalis_gpio3 &pinctrl_apalis_gpio4
-		     &pinctrl_apalis_gpio5 &pinctrl_apalis_gpio6
-		     &pinctrl_apalis_gpio7 &pinctrl_apalis_gpio8
-		    >;
-};
diff --git a/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts b/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts
deleted file mode 100644
index 86e84781cf5d..000000000000
--- a/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts
+++ /dev/null
@@ -1,274 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
-/*
- * Copyright 2014-2020 Toradex
- * Copyright 2012 Freescale Semiconductor, Inc.
- * Copyright 2011 Linaro Ltd.
- */
-
-/dts-v1/;
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include "imx6q.dtsi"
-#include "imx6qdl-apalis.dtsi"
-
-/ {
-	model = "Toradex Apalis iMX6Q/D Module on Ixora Carrier Board V1.1";
-	compatible = "toradex,apalis_imx6q-ixora-v1.1",
-		     "toradex,apalis_imx6q-ixora", "toradex,apalis_imx6q",
-		     "fsl,imx6q";
-
-	aliases {
-		i2c0 = &i2c1;
-		i2c1 = &i2c3;
-		i2c2 = &i2c2;
-		rtc0 = &rtc_i2c;
-		rtc1 = &snvs_rtc;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpio_keys>;
-
-		wakeup {
-			label = "Wake-Up";
-			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_WAKEUP>;
-			debounce-interval = <10>;
-			wakeup-source;
-		};
-	};
-
-	lcd_display: disp0 {
-		compatible = "fsl,imx-parallel-display";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		interface-pix-fmt = "rgb24";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_ipu1_lcdif>;
-		status = "okay";
-
-		port@0 {
-			reg = <0>;
-
-			lcd_display_in: endpoint {
-				remote-endpoint = <&ipu1_di1_disp1>;
-			};
-		};
-
-		port@1 {
-			reg = <1>;
-
-			lcd_display_out: endpoint {
-				remote-endpoint = <&lcd_panel_in>;
-			};
-		};
-	};
-
-	panel: panel {
-		/*
-		 * edt,et057090dhu: EDT 5.7" LCD TFT
-		 * edt,et070080dh6: EDT 7.0" LCD TFT
-		 */
-		compatible = "edt,et057090dhu";
-		backlight = <&backlight>;
-
-		port {
-			lcd_panel_in: endpoint {
-				remote-endpoint = <&lcd_display_out>;
-			};
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_leds_ixora>;
-
-		led4-green {
-			label = "LED_4_GREEN";
-			gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
-		};
-
-		led4-red {
-			label = "LED_4_RED";
-			gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
-		};
-
-		led5-green {
-			label = "LED_5_GREEN";
-			gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
-		};
-
-		led5-red {
-			label = "LED_5_RED";
-			gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
-		};
-	};
-};
-
-&backlight {
-	brightness-levels = <0 127 191 223 239 247 251 255>;
-	default-brightness-level = <1>;
-	status = "okay";
-};
-
-&can1 {
-	status = "okay";
-};
-
-&can2 {
-	status = "okay";
-};
-
-&hdmi {
-	status = "okay";
-};
-
-/* I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier board) */
-&i2c1 {
-	status = "okay";
-
-	/*
-	 * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
-	 * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
-	 */
-	touchscreen@4a {
-		compatible = "atmel,maxtouch";
-		reg = <0x4a>;
-		interrupt-parent = <&gpio6>;
-		interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
-		reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>; /* SODIMM 13 */
-		status = "disabled";
-	};
-
-	/* M41T0M6 real time clock on carrier board */
-	rtc_i2c: rtc@68 {
-		compatible = "st,m41t0";
-		reg = <0x68>;
-	};
-};
-
-/*
- * I2C3_SDA/SCL (CAM) on MXM3 pin 201/203 (e.g. camera sensor on carrier
- * board)
- */
-&i2c3 {
-	status = "okay";
-};
-
-&ipu1_di1_disp1 {
-	remote-endpoint = <&lcd_display_in>;
-};
-
-&ldb {
-	status = "okay";
-};
-
-&pcie {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_reset_moci>;
-	/* active-high meaning opposite of regular PERST# active-low polarity */
-	reset-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
-	reset-gpio-active-high;
-	status = "okay";
-};
-
-&pwm1 {
-	status = "okay";
-};
-
-&pwm2 {
-	status = "okay";
-};
-
-&pwm3 {
-	status = "okay";
-};
-
-&pwm4 {
-	status = "okay";
-};
-
-&reg_usb_otg_vbus {
-	status = "okay";
-};
-
-&reg_usb_host_vbus {
-	status = "okay";
-};
-
-&sata {
-	status = "okay";
-};
-
-&sound_spdif {
-	status = "okay";
-};
-
-&spdif {
-	status = "okay";
-};
-
-&uart1 {
-	status = "okay";
-};
-
-&uart2 {
-	status = "okay";
-};
-
-&uart4 {
-	status = "okay";
-};
-
-&uart5 {
-	status = "okay";
-};
-
-&usbh1 {
-	vbus-supply = <&reg_usb_host_vbus>;
-	status = "okay";
-};
-
-&usbotg {
-	vbus-supply = <&reg_usb_otg_vbus>;
-	status = "okay";
-};
-
-/* MMC1 */
-&usdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc1_4bit &pinctrl_mmc_cd>;
-	cd-gpios = <&gpio4 20 GPIO_ACTIVE_LOW>;
-	bus-width = <4>;
-	status = "okay";
-};
-
-&iomuxc {
-	/*
-	 * Mux the Apalis GPIOs
-	 */
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_apalis_gpio1 &pinctrl_apalis_gpio2
-		     &pinctrl_apalis_gpio3 &pinctrl_apalis_gpio4
-		     &pinctrl_apalis_gpio5 &pinctrl_apalis_gpio6
-		     &pinctrl_apalis_gpio7 &pinctrl_apalis_gpio8
-		    >;
-
-	pinctrl_leds_ixora: ledsixoragrp {
-		fsl,pins = <
-			MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x1b0b0
-			MX6QDL_PAD_SD2_DAT3__GPIO1_IO12 0x1b0b0
-			MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0
-			MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0
-		>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx6q-arm2.dts b/arch/arm/boot/dts/imx6q-arm2.dts
deleted file mode 100644
index 0b40f52268b3..000000000000
--- a/arch/arm/boot/dts/imx6q-arm2.dts
+++ /dev/null
@@ -1,225 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2011 Freescale Semiconductor, Inc.
- * Copyright 2011 Linaro Ltd.
- */
-
-/dts-v1/;
-#include <dt-bindings/gpio/gpio.h>
-#include "imx6q.dtsi"
-
-/ {
-	model = "Freescale i.MX6 Quad Armadillo2 Board";
-	compatible = "fsl,imx6q-arm2", "fsl,imx6q";
-
-	memory@10000000 {
-		device_type = "memory";
-		reg = <0x10000000 0x80000000>;
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-		reg_usb_otg_vbus: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 22 0>;
-			enable-active-high;
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		debug-led {
-			label = "Heartbeat";
-			gpios = <&gpio3 25 0>;
-			linux,default-trigger = "heartbeat";
-		};
-	};
-};
-
-&gpmi {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_gpmi_nand>;
-	status = "disabled"; /* gpmi nand conflicts with SD */
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_hog>;
-
-	imx6q-arm2 {
-		pinctrl_hog: hoggrp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D25__GPIO3_IO25 0x80000000
-			>;
-		};
-
-		pinctrl_enet: enetgrp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL1__ENET_MDIO		0x1b0b0
-				MX6QDL_PAD_KEY_COL2__ENET_MDC		0x1b0b0
-				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
-				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
-				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
-				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
-				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
-				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
-				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
-				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
-				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
-				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
-				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
-				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
-				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
-				MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
-			>;
-		};
-
-		pinctrl_gpmi_nand: gpminandgrp {
-			fsl,pins = <
-				MX6QDL_PAD_NANDF_CLE__NAND_CLE		0xb0b1
-				MX6QDL_PAD_NANDF_ALE__NAND_ALE		0xb0b1
-				MX6QDL_PAD_NANDF_WP_B__NAND_WP_B	0xb0b1
-				MX6QDL_PAD_NANDF_RB0__NAND_READY_B	0xb000
-				MX6QDL_PAD_NANDF_CS0__NAND_CE0_B	0xb0b1
-				MX6QDL_PAD_NANDF_CS1__NAND_CE1_B	0xb0b1
-				MX6QDL_PAD_SD4_CMD__NAND_RE_B		0xb0b1
-				MX6QDL_PAD_SD4_CLK__NAND_WE_B		0xb0b1
-				MX6QDL_PAD_NANDF_D0__NAND_DATA00	0xb0b1
-				MX6QDL_PAD_NANDF_D1__NAND_DATA01	0xb0b1
-				MX6QDL_PAD_NANDF_D2__NAND_DATA02	0xb0b1
-				MX6QDL_PAD_NANDF_D3__NAND_DATA03	0xb0b1
-				MX6QDL_PAD_NANDF_D4__NAND_DATA04	0xb0b1
-				MX6QDL_PAD_NANDF_D5__NAND_DATA05	0xb0b1
-				MX6QDL_PAD_NANDF_D6__NAND_DATA06	0xb0b1
-				MX6QDL_PAD_NANDF_D7__NAND_DATA07	0xb0b1
-				MX6QDL_PAD_SD4_DAT0__NAND_DQS		0x00b1
-			>;
-		};
-
-		pinctrl_uart2: uart2grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D26__UART2_RX_DATA	0x1b0b1
-				MX6QDL_PAD_EIM_D27__UART2_TX_DATA	0x1b0b1
-				MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B	0x1b0b1
-				MX6QDL_PAD_EIM_D29__UART2_DTE_RTS_B	0x1b0b1
-			>;
-		};
-
-		pinctrl_uart4: uart4grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL0__UART4_TX_DATA	0x1b0b1
-				MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA	0x1b0b1
-			>;
-		};
-
-		pinctrl_usbotg: usbotggrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
-			>;
-		};
-
-		pinctrl_usdhc3: usdhc3grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
-				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
-				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
-				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
-				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
-				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
-				MX6QDL_PAD_SD3_DAT4__SD3_DATA4		0x17059
-				MX6QDL_PAD_SD3_DAT5__SD3_DATA5		0x17059
-				MX6QDL_PAD_SD3_DAT6__SD3_DATA6		0x17059
-				MX6QDL_PAD_SD3_DAT7__SD3_DATA7		0x17059
-			>;
-		};
-
-		pinctrl_usdhc3_cdwp: usdhc3cdwp {
-			fsl,pins = <
-				MX6QDL_PAD_NANDF_CS0__GPIO6_IO11 0x80000000
-				MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x80000000
-			>;
-		};
-
-		pinctrl_usdhc4: usdhc4grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
-				MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
-				MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
-				MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
-				MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
-				MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059
-				MX6QDL_PAD_SD4_DAT4__SD4_DATA4		0x17059
-				MX6QDL_PAD_SD4_DAT5__SD4_DATA5		0x17059
-				MX6QDL_PAD_SD4_DAT6__SD4_DATA6		0x17059
-				MX6QDL_PAD_SD4_DAT7__SD4_DATA7		0x17059
-			>;
-		};
-	};
-};
-
-&fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
-	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
-			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
-	fsl,err006687-workaround-present;
-	status = "okay";
-};
-
-&usbotg {
-	vbus-supply = <&reg_usb_otg_vbus>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbotg>;
-	disable-over-current;
-	status = "okay";
-};
-
-&usdhc3 {
-	cd-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>;
-	vmmc-supply = <&reg_3p3v>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc3
-		     &pinctrl_usdhc3_cdwp>;
-	status = "okay";
-};
-
-&usdhc4 {
-	non-removable;
-	vmmc-supply = <&reg_3p3v>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc4>;
-	status = "okay";
-};
-
-&uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
-	fsl,dte-mode;
-	uart-has-rtscts;
-	status = "okay";
-};
-
-&uart4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart4>;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6q-display5-tianma-tm070-1280x768.dts b/arch/arm/boot/dts/imx6q-display5-tianma-tm070-1280x768.dts
deleted file mode 100644
index 16658b76fc4e..000000000000
--- a/arch/arm/boot/dts/imx6q-display5-tianma-tm070-1280x768.dts
+++ /dev/null
@@ -1,51 +0,0 @@
-/*
- * Copyright 2017
- * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is licensed under the terms of the GNU General Public
- *     License version 2.  This program is licensed "as is" without
- *     any warranty of any kind, whether express or implied.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-
-#include "imx6q-display5.dtsi"
-
-&panel {
-	compatible = "tianma,tm070jdhg30";
-};
-
-&ldb {
-	lvds0: lvds-channel@0 {
-		fsl,data-mapping = "spwg";
-		fsl,data-width = <18>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx6q-gk802.dts b/arch/arm/boot/dts/imx6q-gk802.dts
deleted file mode 100644
index ccc2487d47ca..000000000000
--- a/arch/arm/boot/dts/imx6q-gk802.dts
+++ /dev/null
@@ -1,179 +0,0 @@
-/*
- * Copyright (C) 2013 Philipp Zabel
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
-
-/dts-v1/;
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include "imx6q.dtsi"
-
-/ {
-	model = "Zealz GK802";
-	compatible = "zealz,imx6q-gk802", "fsl,imx6q";
-
-	chosen {
-		stdout-path = &uart4;
-	};
-
-	memory@10000000 {
-		device_type = "memory";
-		reg = <0x10000000 0x40000000>;
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		recovery-button {
-			label = "recovery";
-			gpios = <&gpio3 16 1>;
-			linux,code = <KEY_RESTART>;
-			wakeup-source;
-		};
-	};
-};
-
-&hdmi {
-	ddc-i2c-bus = <&i2c3>;
-	status = "okay";
-};
-
-/* Internal I2C */
-&i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c2>;
-	clock-frequency = <100000>;
-	status = "okay";
-
-	/* SDMC DM2016 1024 bit EEPROM + 128 bit OTP */
-	eeprom: dm2016@51 {
-		compatible = "sdmc,dm2016";
-		reg = <0x51>;
-	};
-};
-
-/* External I2C via HDMI */
-&i2c3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c3>;
-	clock-frequency = <100000>;
-	status = "okay";
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_hog>;
-
-	imx6q-gk802 {
-		pinctrl_hog: hoggrp {
-			fsl,pins = <
-				/* Recovery button, active-low */
-				MX6QDL_PAD_EIM_D16__GPIO3_IO16  0x100b1
-				/* RTL8192CU enable GPIO, active-low */
-				MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b0b0
-			>;
-		};
-
-		pinctrl_i2c2: i2c2grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
-				MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
-			>;
-		};
-
-		pinctrl_i2c3: i2c3grp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_5__I2C3_SCL		0x4001b8b1
-				MX6QDL_PAD_GPIO_16__I2C3_SDA		0x4001b8b1
-			>;
-		};
-
-		pinctrl_uart4: uart4grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL0__UART4_TX_DATA	0x1b0b1
-				MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA	0x1b0b1
-			>;
-		};
-
-		pinctrl_usdhc3: usdhc3grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
-				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
-				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
-				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
-				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
-				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
-			>;
-		};
-
-		pinctrl_usdhc4: usdhc4grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
-				MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
-				MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
-				MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
-				MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
-				MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059
-			>;
-		};
-	};
-};
-
-&uart2 {
-	status = "okay";
-};
-
-&uart4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart4>;
-	status = "okay";
-};
-
-/* External USB-A port (USBOTG) */
-&usbotg {
-	disable-over-current;
-	status = "okay";
-};
-
-/* Internal USB port (USBH1), connected to RTL8192CU */
-&usbh1 {
-	disable-over-current;
-	status = "okay";
-};
-
-/* External microSD */
-&usdhc3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc3>;
-	bus-width = <4>;
-	cd-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
-	vmmc-supply = <&reg_3p3v>;
-	status = "okay";
-};
-
-/* Internal microSD */
-&usdhc4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc4>;
-	bus-width = <4>;
-	vmmc-supply = <&reg_3p3v>;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6q-gw551x.dts b/arch/arm/boot/dts/imx6q-gw551x.dts
deleted file mode 100644
index 2c7feeef1b0e..000000000000
--- a/arch/arm/boot/dts/imx6q-gw551x.dts
+++ /dev/null
@@ -1,55 +0,0 @@
-/*
- * Copyright 2014 Gateworks Corporation
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of
- *     the License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- *     You should have received a copy of the GNU General Public
- *     License along with this file; if not, write to the Free
- *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
- *     MA 02110-1301 USA
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6q.dtsi"
-#include "imx6qdl-gw551x.dtsi"
-
-/ {
-	model = "Gateworks Ventana i.MX6 Dual/Quad GW551X";
-	compatible = "gw,imx6q-gw551x", "gw,ventana", "fsl,imx6q";
-};
diff --git a/arch/arm/boot/dts/imx6q-gw553x.dts b/arch/arm/boot/dts/imx6q-gw553x.dts
deleted file mode 100644
index e9c224cea752..000000000000
--- a/arch/arm/boot/dts/imx6q-gw553x.dts
+++ /dev/null
@@ -1,55 +0,0 @@
-/*
- * Copyright 2016 Gateworks Corporation
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of
- *     the License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- *     You should have received a copy of the GNU General Public
- *     License along with this file; if not, write to the Free
- *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
- *     MA 02110-1301 USA
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6q.dtsi"
-#include "imx6qdl-gw553x.dtsi"
-
-/ {
-	model = "Gateworks Ventana i.MX6 Dual/Quad GW553X";
-	compatible = "gw,imx6q-gw553x", "gw,ventana", "fsl,imx6q";
-};
diff --git a/arch/arm/boot/dts/imx6q-gw560x.dts b/arch/arm/boot/dts/imx6q-gw560x.dts
deleted file mode 100644
index 735f2bbf1439..000000000000
--- a/arch/arm/boot/dts/imx6q-gw560x.dts
+++ /dev/null
@@ -1,59 +0,0 @@
-/*
- * Copyright 2017 Gateworks Corporation
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of
- *     the License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- *     You should have received a copy of the GNU General Public
- *     License along with this file; if not, write to the Free
- *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
- *     MA 02110-1301 USA
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6q.dtsi"
-#include "imx6qdl-gw560x.dtsi"
-
-/ {
-	model = "Gateworks Ventana i.MX6 Dual/Quad GW560X";
-	compatible = "gw,imx6q-gw560x", "gw,ventana", "fsl,imx6q";
-};
-
-&sata {
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6q-gw5903.dts b/arch/arm/boot/dts/imx6q-gw5903.dts
deleted file mode 100644
index a182e4cb0e6e..000000000000
--- a/arch/arm/boot/dts/imx6q-gw5903.dts
+++ /dev/null
@@ -1,55 +0,0 @@
-/*
- * Copyright 2017 Gateworks Corporation
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of
- *     the License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- *     You should have received a copy of the GNU General Public
- *     License along with this file; if not, write to the Free
- *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
- *     MA 02110-1301 USA
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6q.dtsi"
-#include "imx6qdl-gw5903.dtsi"
-
-/ {
-	model = "Gateworks Ventana i.MX6 Dual/Quad GW5903";
-	compatible = "gw,imx6q-gw5903", "gw,ventana", "fsl,imx6q";
-};
diff --git a/arch/arm/boot/dts/imx6q-gw5904.dts b/arch/arm/boot/dts/imx6q-gw5904.dts
deleted file mode 100644
index ca1e2ae3341e..000000000000
--- a/arch/arm/boot/dts/imx6q-gw5904.dts
+++ /dev/null
@@ -1,59 +0,0 @@
-/*
- * Copyright 2017 Gateworks Corporation
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of
- *     the License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- *     You should have received a copy of the GNU General Public
- *     License along with this file; if not, write to the Free
- *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
- *     MA 02110-1301 USA
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6q.dtsi"
-#include "imx6qdl-gw5904.dtsi"
-
-/ {
-	model = "Gateworks Ventana i.MX6 Dual/Quad GW5904";
-	compatible = "gw,imx6q-gw5904", "gw,ventana", "fsl,imx6q";
-};
-
-&sata {
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6q-kontron-samx6i.dtsi b/arch/arm/boot/dts/imx6q-kontron-samx6i.dtsi
deleted file mode 100644
index 4d6a0c3e8455..000000000000
--- a/arch/arm/boot/dts/imx6q-kontron-samx6i.dtsi
+++ /dev/null
@@ -1,35 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0 OR X11
-/*
- * Copyright 2019 (C) Pengutronix, Marco Felsch <kernel@pengutronix.de>
- */
-
-#include "imx6q.dtsi"
-#include "imx6qdl-kontron-samx6i.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
-	model = "Kontron SMARC sAMX6i Quad/Dual";
-	compatible = "kontron,imx6q-samx6i", "fsl,imx6q";
-};
-
-/* Quad/Dual SoMs have 3 chip-select signals */
-&ecspi4 {
-	cs-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>,
-		   <&gpio3 29 GPIO_ACTIVE_LOW>,
-		   <&gpio3 25 GPIO_ACTIVE_LOW>;
-};
-
-&pinctrl_ecspi4 {
-	fsl,pins = <
-		MX6QDL_PAD_EIM_D21__ECSPI4_SCLK 0x100b1
-		MX6QDL_PAD_EIM_D28__ECSPI4_MOSI 0x100b1
-		MX6QDL_PAD_EIM_D22__ECSPI4_MISO 0x100b1
-
-		/* SPI4_IMX_CS2# - connected to internal flash */
-		MX6QDL_PAD_EIM_D24__GPIO3_IO24 0x1b0b0
-		/* SPI4_IMX_CS0# - connected to SMARC SPI0_CS0# */
-		MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1b0b0
-		/* SPI4_CS3# - connected to  SMARC SPI0_CS1# */
-		MX6QDL_PAD_EIM_D25__GPIO3_IO25 0x1b0b0
-	>;
-};
diff --git a/arch/arm/boot/dts/imx6q-sabrelite.dts b/arch/arm/boot/dts/imx6q-sabrelite.dts
deleted file mode 100644
index dc51262e7b2f..000000000000
--- a/arch/arm/boot/dts/imx6q-sabrelite.dts
+++ /dev/null
@@ -1,59 +0,0 @@
-/*
- * Copyright 2011 Freescale Semiconductor, Inc.
- * Copyright 2011 Linaro Ltd.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6q.dtsi"
-#include "imx6qdl-sabrelite.dtsi"
-
-/ {
-	model = "Freescale i.MX6 Quad SABRE Lite Board";
-	compatible = "fsl,imx6q-sabrelite", "fsl,imx6q";
-};
-
-&sata {
-	status = "okay";
-};
-
-&ipu1_csi1_from_mipi_vc1 {
-	clock-lanes = <0>;
-	data-lanes = <1 2>;
-};
diff --git a/arch/arm/boot/dts/imx6q-sbc6x.dts b/arch/arm/boot/dts/imx6q-sbc6x.dts
deleted file mode 100644
index 9054c1d58b9d..000000000000
--- a/arch/arm/boot/dts/imx6q-sbc6x.dts
+++ /dev/null
@@ -1,93 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright 2013 Pavel Machek <pavel@denx.de>
- */
-
-/dts-v1/;
-#include "imx6q.dtsi"
-
-/ {
-	model = "MicroSys sbc6x board";
-	compatible = "microsys,sbc6x", "fsl,imx6q";
-
-	memory@10000000 {
-		device_type = "memory";
-		reg = <0x10000000 0x80000000>;
-	};
-};
-
-
-&fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
-	status = "okay";
-};
-
-&iomuxc {
-	imx6q-sbc6x {
-		pinctrl_enet: enetgrp {
-			fsl,pins = <
-				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
-				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
-				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
-				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
-				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
-				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
-				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
-				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
-				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
-				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
-				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
-				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
-				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
-				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
-				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
-				MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
-			>;
-		};
-
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0b1
-				MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0b1
-			>;
-		};
-
-		pinctrl_usbotg: usbotggrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
-			>;
-		};
-
-		pinctrl_usdhc3: usdhc3grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
-				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
-				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
-				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
-				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
-				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
-			>;
-		};
-	};
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
-	status = "okay";
-};
-
-&usbotg {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbotg>;
-	disable-over-current;
-	status = "okay";
-};
-
-&usdhc3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc3>;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1010-comtft.dts b/arch/arm/boot/dts/imx6q-tx6q-1010-comtft.dts
deleted file mode 100644
index ac3050a835e5..000000000000
--- a/arch/arm/boot/dts/imx6q-tx6q-1010-comtft.dts
+++ /dev/null
@@ -1,79 +0,0 @@
-/*
- * Copyright 2014-2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6q.dtsi"
-#include "imx6qdl-tx6.dtsi"
-#include "imx6qdl-tx6-lcd.dtsi"
-
-/ {
-	model = "Ka-Ro electronics TX6Q-1010 Module on CoMpact TFT";
-	compatible = "karo,imx6q-tx6q", "fsl,imx6q";
-};
-
-&backlight {
-	pwms = <&pwm2 0 500000 0>;
-	/delete-property/ turn-on-delay-ms;
-};
-
-&can1 {
-	status = "disabled";
-};
-
-&can2 {
-	xceiver-supply = <&reg_3v3>;
-};
-
-&kpp {
-	status = "disabled";
-};
-
-&lcd_panel {
-	compatible = "edt,etm0700g0edh6";
-};
-
-&reg_can_xcvr {
-	status = "disabled";
-};
-
-&touchscreen {
-	status = "disabled";
-};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1010.dts b/arch/arm/boot/dts/imx6q-tx6q-1010.dts
deleted file mode 100644
index 4ee860b626ff..000000000000
--- a/arch/arm/boot/dts/imx6q-tx6q-1010.dts
+++ /dev/null
@@ -1,54 +0,0 @@
-/*
- * Copyright 2014-2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6q.dtsi"
-#include "imx6qdl-tx6.dtsi"
-#include "imx6qdl-tx6-lcd.dtsi"
-
-/ {
-	model = "Ka-Ro electronics TX6Q-1010/-1030 Module";
-	compatible = "karo,imx6q-tx6q", "fsl,imx6q";
-};
-
-&ipu2 {
-	status = "disabled";
-};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1020-comtft.dts b/arch/arm/boot/dts/imx6q-tx6q-1020-comtft.dts
deleted file mode 100644
index a773f252816c..000000000000
--- a/arch/arm/boot/dts/imx6q-tx6q-1020-comtft.dts
+++ /dev/null
@@ -1,110 +0,0 @@
-/*
- * Copyright 2014-2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6q.dtsi"
-#include "imx6qdl-tx6.dtsi"
-#include "imx6qdl-tx6-lcd.dtsi"
-
-/ {
-	model = "Ka-Ro electronics TX6Q-1020 Module on CoMpact TFT";
-	compatible = "karo,imx6q-tx6q", "fsl,imx6q";
-};
-
-&backlight {
-	pwms = <&pwm2 0 500000 0>;
-	/delete-property/ turn-on-delay-ms;
-};
-
-&can1 {
-	status = "disabled";
-};
-
-&can2 {
-	xceiver-supply = <&reg_3v3>;
-};
-
-&ds1339 {
-	status = "disabled";
-};
-
-&gpmi {
-	status = "disabled";
-};
-
-&kpp {
-	status = "disabled";
-};
-
-&lcd_panel {
-	compatible = "edt,etm0700g0edh6";
-};
-
-&reg_can_xcvr {
-	status = "disabled";
-};
-
-&touchscreen {
-	status = "disabled";
-};
-
-&usdhc4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc4>;
-	bus-width = <4>;
-	no-1-8-v;
-	fsl,wp-controller;
-	status = "okay";
-};
-
-&iomuxc {
-	pinctrl_usdhc4: usdhc4grp {
-		fsl,pins = <
-			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x070b1
-			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x070b1
-			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x070b1
-			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x070b1
-			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x070b1
-			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x070b1
-			MX6QDL_PAD_NANDF_ALE__SD4_RESET		0x0b0b1
-		>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1020.dts b/arch/arm/boot/dts/imx6q-tx6q-1020.dts
deleted file mode 100644
index 0a4daec8d3ad..000000000000
--- a/arch/arm/boot/dts/imx6q-tx6q-1020.dts
+++ /dev/null
@@ -1,86 +0,0 @@
-/*
- * Copyright 2014-2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6q.dtsi"
-#include "imx6qdl-tx6.dtsi"
-#include "imx6qdl-tx6-lcd.dtsi"
-
-/ {
-	model = "Ka-Ro electronics TX6Q-1020 Module";
-	compatible = "karo,imx6q-tx6q", "fsl,imx6q";
-};
-
-&ds1339 {
-	status = "disabled";
-};
-
-&gpmi {
-	status = "disabled";
-};
-
-&ipu2 {
-	status = "disabled";
-};
-
-&usdhc4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc4>;
-	bus-width = <4>;
-	non-removable;
-	no-1-8-v;
-	fsl,wp-controller;
-	status = "okay";
-};
-
-&iomuxc {
-	pinctrl_usdhc4: usdhc4grp {
-		fsl,pins = <
-			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x070b1
-			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x070b1
-			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x070b1
-			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x070b1
-			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x070b1
-			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x070b1
-			MX6QDL_PAD_NANDF_ALE__SD4_RESET		0x0b0b1
-		>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1036-mb7.dts b/arch/arm/boot/dts/imx6q-tx6q-1036-mb7.dts
deleted file mode 100644
index 9ffbb0fe7df8..000000000000
--- a/arch/arm/boot/dts/imx6q-tx6q-1036-mb7.dts
+++ /dev/null
@@ -1,48 +0,0 @@
-/*
- * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6q-tx6q-1036.dts"
-#include "imx6qdl-tx6-mb7.dtsi"
-
-/ {
-	model = "Ka-Ro electronics TX6Q-1036 Module on MB7 baseboard";
-};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1036.dts b/arch/arm/boot/dts/imx6q-tx6q-1036.dts
deleted file mode 100644
index cb2fcb4896c6..000000000000
--- a/arch/arm/boot/dts/imx6q-tx6q-1036.dts
+++ /dev/null
@@ -1,86 +0,0 @@
-/*
- * Copyright 2014-2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6q.dtsi"
-#include "imx6qdl-tx6.dtsi"
-#include "imx6qdl-tx6-lcd.dtsi"
-
-/ {
-	model = "Ka-Ro electronics TX6Q-1036 Module";
-	compatible = "karo,imx6q-tx6q", "fsl,imx6q";
-};
-
-&ds1339 {
-	status = "disabled";
-};
-
-&gpmi {
-	status = "disabled";
-};
-
-&ipu2 {
-	status = "disabled";
-};
-
-&usdhc4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc4>;
-	bus-width = <4>;
-	non-removable;
-	no-1-8-v;
-	fsl,wp-controller;
-	status = "okay";
-};
-
-&iomuxc {
-	pinctrl_usdhc4: usdhc4grp {
-		fsl,pins = <
-			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x070b1
-			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x070b1
-			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x070b1
-			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x070b1
-			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x070b1
-			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x070b1
-			MX6QDL_PAD_NANDF_ALE__SD4_RESET		0x0b0b1
-		>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-10x0-mb7.dts b/arch/arm/boot/dts/imx6q-tx6q-10x0-mb7.dts
deleted file mode 100644
index d43a5d8f1749..000000000000
--- a/arch/arm/boot/dts/imx6q-tx6q-10x0-mb7.dts
+++ /dev/null
@@ -1,48 +0,0 @@
-/*
- * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6q-tx6q-1010.dts"
-#include "imx6qdl-tx6-mb7.dtsi"
-
-/ {
-	model = "Ka-Ro electronics TX6Q-1010/-1030 Module on MB7 baseboard";
-};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-1110.dts b/arch/arm/boot/dts/imx6q-tx6q-1110.dts
deleted file mode 100644
index f7b0acb65352..000000000000
--- a/arch/arm/boot/dts/imx6q-tx6q-1110.dts
+++ /dev/null
@@ -1,58 +0,0 @@
-/*
- * Copyright 2014-2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6q.dtsi"
-#include "imx6qdl-tx6.dtsi"
-#include "imx6qdl-tx6-lvds.dtsi"
-
-/ {
-	model = "Ka-Ro electronics TX6Q-1110/-1130 Module";
-	compatible = "karo,imx6q-tx6q", "fsl,imx6q";
-};
-
-&ipu2 {
-	status = "disabled";
-};
-
-&sata {
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6q-tx6q-11x0-mb7.dts b/arch/arm/boot/dts/imx6q-tx6q-11x0-mb7.dts
deleted file mode 100644
index 387edf2b3f96..000000000000
--- a/arch/arm/boot/dts/imx6q-tx6q-11x0-mb7.dts
+++ /dev/null
@@ -1,48 +0,0 @@
-/*
- * Copyright 2016-2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6q-tx6q-1110.dts"
-#include "imx6qdl-tx6-mb7.dtsi"
-
-/ {
-	model = "Ka-Ro electronics TX6Q-1110/-1130 Module on MB7 baseboard";
-};
diff --git a/arch/arm/boot/dts/imx6qdl-aristainetos.dtsi b/arch/arm/boot/dts/imx6qdl-aristainetos.dtsi
deleted file mode 100644
index e21f6ac864e5..000000000000
--- a/arch/arm/boot/dts/imx6qdl-aristainetos.dtsi
+++ /dev/null
@@ -1,408 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * support fot the imx6 based aristainetos board
- *
- * Copyright (C) 2014 Heiko Schocher <hs@denx.de>
- */
-
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
-
-	reg_2p5v: regulator-2p5v {
-		compatible = "regulator-fixed";
-		regulator-name = "2P5V";
-		regulator-min-microvolt = <2500000>;
-		regulator-max-microvolt = <2500000>;
-		regulator-always-on;
-	};
-
-	reg_3p3v: regulator-3p3v {
-		compatible = "regulator-fixed";
-		regulator-name = "3P3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-
-	reg_usbh1_vbus: regulator-usbh1-vbus {
-		compatible = "regulator-fixed";
-		enable-active-high;
-		gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_aristainetos_usbh1_vbus>;
-		regulator-name = "usb_h1_vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-	};
-
-	reg_usbotg_vbus: regulator-usbotg-vbus {
-		compatible = "regulator-fixed";
-		enable-active-high;
-		gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_aristainetos_usbotg_vbus>;
-		regulator-name = "usb_otg_vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-	};
-};
-
-&audmux {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_audmux>;
-	status = "okay";
-};
-
-&can1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_flexcan1>;
-	status = "okay";
-};
-
-&can2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_flexcan2>;
-	status = "okay";
-};
-
-&i2c1 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c1>;
-	status = "okay";
-
-	tmp103: tmp103@71 {
-		compatible = "ti,tmp103";
-		reg = <0x71>;
-	};
-};
-
-&i2c3 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c3>;
-	status = "okay";
-
-	rtc@68 {
-		compatible = "dallas,m41t00";
-		reg = <0x68>;
-	};
-};
-
-&ecspi4 {
-	cs-gpios = <&gpio3 20 GPIO_ACTIVE_LOW>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi4>;
-	status = "okay";
-
-	flash: m25p80@0 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "micron,n25q128a11", "jedec,spi-nor";
-		spi-max-frequency = <20000000>;
-		reg = <0>;
-	};
-};
-
-&fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rmii";
-	phy-reset-gpios = <&gpio3 29 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-&gpmi {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_gpmi_nand>;
-	status = "okay";
-};
-
-&pcie {
-	status = "okay";
-};
-
-&uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
-	status = "okay";
-};
-
-
-&uart4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart4>;
-	uart-has-rtscts;
-	status = "okay";
-};
-
-&uart5 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart5>;
-	uart-has-rtscts;
-	status = "okay";
-};
-
-&usbh1 {
-	vbus-supply = <&reg_usbh1_vbus>;
-	dr_mode = "host";
-	status = "okay";
-};
-
-&usbotg {
-	vbus-supply = <&reg_usbotg_vbus>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbotg>;
-	disable-over-current;
-	dr_mode = "host";
-	status = "okay";
-};
-
-&usdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc1>;
-	vmmc-supply = <&reg_3p3v>;
-	cd-gpios = <&gpio4 7 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-&usdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc2>;
-	vmmc-supply = <&reg_3p3v>;
-	cd-gpios = <&gpio4 8 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_hog &pinctrl_gpio>;
-
-	imx6qdl-aristainetos {
-		pinctrl_aristainetos_usbh1_vbus: aristainetos-usbh1-vbus {
-			fsl,pins = <MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x130b0>;
-		};
-
-		pinctrl_aristainetos_usbotg_vbus: aristainetos-usbotg-vbus {
-			fsl,pins = <MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x130b0>;
-		};
-
-		pinctrl_audmux: audmuxgrp {
-			fsl,pins = <
-				MX6QDL_PAD_CSI0_DAT7__AUD3_RXD  0x1b0b0
-				MX6QDL_PAD_CSI0_DAT4__AUD3_TXC  0x1b0b0
-				MX6QDL_PAD_CSI0_DAT5__AUD3_TXD  0x1b0b0
-				MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x1b0b0
-			>;
-		};
-
-		pinctrl_backlight: backlightgrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_9__PWM1_OUT	0x1b0b0
-				MX6QDL_PAD_SD4_DAT1__PWM3_OUT	0x1b0b0
-				MX6QDL_PAD_GPIO_2__GPIO1_IO02	0x1b0b0
-			>;
-		};
-
-		pinctrl_ecspi2: ecspi2grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
-				MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
-				MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
-				MX6QDL_PAD_EIM_D24__GPIO3_IO24  0x100b1
-			>;
-		};
-
-		pinctrl_ecspi4: ecspi4grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D21__ECSPI4_SCLK 0x100b1
-				MX6QDL_PAD_EIM_D22__ECSPI4_MISO 0x100b1
-				MX6QDL_PAD_EIM_D28__ECSPI4_MOSI 0x100b1
-				MX6QDL_PAD_EIM_D20__GPIO3_IO20  0x100b1
-				MX6QDL_PAD_SD4_DAT7__GPIO2_IO15 0x1b0b0 /* WP pin */
-			>;
-		};
-
-		pinctrl_enet: enetgrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
-				MX6QDL_PAD_ENET_MDIO__ENET_MDIO  0x1b0b0
-				MX6QDL_PAD_ENET_MDC__ENET_MDC    0x1b0b0
-				MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
-				MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
-				MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN   0x1b0b0
-				MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER   0x1b0b0
-				MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
-				MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
-				MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN  0x1b0b0
-			>;
-		};
-
-		pinctrl_flexcan1: flexcan1grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX	0x1b0b0
-				MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b0
-			>;
-		};
-
-		pinctrl_flexcan2: flexcan2grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_DAT0__FLEXCAN2_TX	0x1b0b0
-				MX6QDL_PAD_SD3_DAT1__FLEXCAN2_RX	0x1b0b0
-				>;
-		};
-
-		pinctrl_gpio: gpiogrp {
-			fsl,pins = <
-				MX6QDL_PAD_SD4_DAT2__GPIO2_IO10	0x1b0b0
-				MX6QDL_PAD_SD4_DAT3__GPIO2_IO11	0x1b0b0
-				MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0
-				MX6QDL_PAD_SD4_DAT5__GPIO2_IO13	0x1b0b0
-				MX6QDL_PAD_GPIO_3__GPIO1_IO03	0x1b0b0
-				MX6QDL_PAD_GPIO_4__GPIO1_IO04	0x1b0b0
-				MX6QDL_PAD_GPIO_5__GPIO1_IO05	0x1b0b0
-				MX6QDL_PAD_GPIO_6__GPIO1_IO06	0x1b0b0
-				MX6QDL_PAD_GPIO_7__GPIO1_IO07	0x1b0b0
-				MX6QDL_PAD_GPIO_8__GPIO1_IO08	0x1b0b0
-				MX6QDL_PAD_KEY_COL0__GPIO4_IO06	0x1b0b0
-			>;
-		};
-
-		pinctrl_gpmi_nand: gpminandgrp {
-			fsl,pins = <
-				MX6QDL_PAD_NANDF_CLE__NAND_CLE     0xb0b1
-				MX6QDL_PAD_NANDF_ALE__NAND_ALE     0xb0b1
-				MX6QDL_PAD_NANDF_WP_B__NAND_WP_B   0xb0b1
-				MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
-				MX6QDL_PAD_NANDF_CS0__NAND_CE0_B   0xb0b1
-				MX6QDL_PAD_NANDF_CS1__NAND_CE1_B   0xb0b1
-				MX6QDL_PAD_SD4_CMD__NAND_RE_B      0xb0b1
-				MX6QDL_PAD_SD4_CLK__NAND_WE_B      0xb0b1
-				MX6QDL_PAD_NANDF_D0__NAND_DATA00   0xb0b1
-				MX6QDL_PAD_NANDF_D1__NAND_DATA01   0xb0b1
-				MX6QDL_PAD_NANDF_D2__NAND_DATA02   0xb0b1
-				MX6QDL_PAD_NANDF_D3__NAND_DATA03   0xb0b1
-				MX6QDL_PAD_NANDF_D4__NAND_DATA04   0xb0b1
-				MX6QDL_PAD_NANDF_D5__NAND_DATA05   0xb0b1
-				MX6QDL_PAD_NANDF_D6__NAND_DATA06   0xb0b1
-				MX6QDL_PAD_NANDF_D7__NAND_DATA07   0xb0b1
-				MX6QDL_PAD_SD4_DAT0__NAND_DQS      0x00b1
-			>;
-		};
-
-		pinctrl_hog: hoggrp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D29__GPIO3_IO29   0x10
-			>;
-		};
-
-		pinctrl_i2c1: i2c1grp {
-			fsl,pins = <
-				MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
-				MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
-			>;
-		};
-
-		pinctrl_i2c2: i2c2grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
-				MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
-			>;
-		};
-
-		pinctrl_i2c3: i2c3grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1
-				MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
-			>;
-		};
-
-		pinctrl_ipu_disp: ipudisp1grp {
-			fsl,pins = <
-				MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x10
-				MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15		0x10
-				MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x10
-				MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x10
-				MX6QDL_PAD_DI0_PIN4__GPIO4_IO20			0x20000
-				MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x10
-				MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x10
-				MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x10
-				MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x10
-				MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x10
-				MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x10
-				MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x10
-				MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x10
-				MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x10
-				MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x10
-				MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x10
-				MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x10
-				MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x10
-				MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x10
-				MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x10
-				MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x10
-				MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x10
-				MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x10
-				MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18	0x10
-				MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19	0x10
-				MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20	0x10
-				MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21	0x10
-				MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22	0x10
-				MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23	0x10
-				>;
-		};
-
-		pinctrl_uart2: uart2grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1
-				MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1
-			>;
-		};
-
-		pinctrl_uart4: uart4grp {
-			fsl,pins = <
-				MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x1b0b1
-				MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x1b0b1
-				MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B 0x1b0b1
-				MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B 0x1b0b1
-			>;
-		};
-
-		pinctrl_uart5: uart5grp {
-			fsl,pins = <
-				MX6QDL_PAD_CSI0_DAT14__UART5_TX_DATA 0x1b0b1
-				MX6QDL_PAD_CSI0_DAT15__UART5_RX_DATA 0x1b0b1
-			>;
-		};
-
-		pinctrl_usbotg: usbotggrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
-			>;
-		};
-
-		pinctrl_usdhc1: usdhc1grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_CMD__SD1_CMD    0x17059
-				MX6QDL_PAD_SD1_CLK__SD1_CLK    0x10059
-				MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
-				MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
-				MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
-				MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
-				MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x1b0b0
-			>;
-		};
-
-		pinctrl_usdhc2: usdhc2grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD2_CMD__SD2_CMD    0x17059
-				MX6QDL_PAD_SD2_CLK__SD2_CLK    0x10059
-				MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
-				MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
-				MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
-				MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059
-				MX6QDL_PAD_KEY_COL1__GPIO4_IO08 0x1b0b0
-			>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx6qdl-colibri-v1_1-uhs.dtsi b/arch/arm/boot/dts/imx6qdl-colibri-v1_1-uhs.dtsi
deleted file mode 100644
index 7672fbfc29be..000000000000
--- a/arch/arm/boot/dts/imx6qdl-colibri-v1_1-uhs.dtsi
+++ /dev/null
@@ -1,44 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
-/*
- * Copyright 2020 Toradex
- */
-
-&iomuxc {
-	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
-		fsl,pins = <
-			MX6QDL_PAD_SD1_CMD__SD1_CMD    0x170b1
-			MX6QDL_PAD_SD1_CLK__SD1_CLK    0x100b1
-			MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170b1
-			MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170b1
-			MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170b1
-			MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170b1
-		>;
-	};
-
-	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
-		fsl,pins = <
-			MX6QDL_PAD_SD1_CMD__SD1_CMD    0x170f1
-			MX6QDL_PAD_SD1_CLK__SD1_CLK    0x100f1
-			MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f1
-			MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f1
-			MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f1
-			MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f1
-		>;
-	};
-};
-
-/* Colibri MMC */
-&usdhc1 {
-	pinctrl-names = "default", "state_100mhz", "state_200mhz";
-	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_mmc_cd>;
-	pinctrl-1 = <&pinctrl_usdhc1_100mhz &pinctrl_mmc_cd>;
-	pinctrl-2 = <&pinctrl_usdhc1_200mhz &pinctrl_mmc_cd>;
-	vmmc-supply = <&reg_module_3v3>;
-	vqmmc-supply = <&vgen3_reg>;
-	wakeup-source;
-	keep-power-in-suspend;
-	sd-uhs-sdr12;
-	sd-uhs-sdr25;
-	sd-uhs-sdr50;
-	sd-uhs-sdr104;
-};
diff --git a/arch/arm/boot/dts/imx6qdl-dfi-fs700-m60.dtsi b/arch/arm/boot/dts/imx6qdl-dfi-fs700-m60.dtsi
deleted file mode 100644
index 648f5fcb72e6..000000000000
--- a/arch/arm/boot/dts/imx6qdl-dfi-fs700-m60.dtsi
+++ /dev/null
@@ -1,201 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		dummy_reg: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "dummy-supply";
-		};
-
-		reg_usb_otg_vbus: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 22 0>;
-			enable-active-high;
-		};
-	};
-
-	chosen {
-		stdout-path = &uart1;
-	};
-};
-
-&ecspi3 {
-	cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi3>;
-	status = "okay";
-
-	flash: m25p80@0 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "sst,sst25vf040b", "jedec,spi-nor";
-		spi-max-frequency = <20000000>;
-		reg = <0>;
-	};
-};
-
-&fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet>;
-	status = "okay";
-	phy-mode = "rgmii";
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_hog>;
-
-	imx6qdl-dfi-fs700-m60 {
-		pinctrl_hog: hoggrp {
-			fsl,pins = <
-				MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x80000000
-				MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x80000000 /* PMIC irq */
-				MX6QDL_PAD_EIM_D26__GPIO3_IO26 0x80000000 /* MAX11801 irq */
-				MX6QDL_PAD_NANDF_D5__GPIO2_IO05 0x000030b0 /* Backlight enable */
-			>;
-		};
-
-		pinctrl_enet: enetgrp {
-			fsl,pins = <
-				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
-				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
-				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
-				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
-				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
-				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
-				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
-				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
-				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
-				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
-				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
-				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
-				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
-				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
-				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
-				MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
-			>;
-		};
-
-		pinctrl_i2c2: i2c2grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_EB2__I2C2_SCL		0x4001b8b1
-				MX6QDL_PAD_EIM_D16__I2C2_SDA		0x4001b8b1
-			>;
-		};
-
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0b1
-				MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0b1
-			>;
-		};
-
-		pinctrl_usbotg: usbotggrp {
-			fsl,pins = <
-				MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x17059
-			>;
-		};
-
-		pinctrl_usdhc2: usdhc2grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
-				MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
-				MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
-				MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
-				MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
-				MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
-				MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x80000000 /* card detect */
-			>;
-		};
-
-		pinctrl_usdhc3: usdhc3grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
-				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
-				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
-				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
-				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
-				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
-			>;
-		};
-
-		pinctrl_usdhc4: usdhc4grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
-				MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
-				MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
-				MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
-				MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
-				MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059
-				MX6QDL_PAD_SD4_DAT4__SD4_DATA4		0x17059
-				MX6QDL_PAD_SD4_DAT5__SD4_DATA5		0x17059
-				MX6QDL_PAD_SD4_DAT6__SD4_DATA6		0x17059
-				MX6QDL_PAD_SD4_DAT7__SD4_DATA7		0x17059
-			>;
-		};
-
-		pinctrl_ecspi3: ecspi3grp {
-			fsl,pins = <
-				MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO	0x100b1
-				MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI	0x100b1
-				MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK	0x100b1
-				MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x80000000 /* SPI NOR chipselect */
-			>;
-		};
-	};
-};
-
-&i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c2>;
-	status = "okay";
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
-	status = "okay";
-};
-
-&usbh1 {
-	status = "okay";
-};
-
-&usbotg {
-	vbus-supply = <&reg_usb_otg_vbus>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbotg>;
-	disable-over-current;
-	dr_mode = "host";
-	status = "okay";
-};
-
-&usdhc2 { /* module slot */
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc2>;
-	cd-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-&usdhc3 { /* baseboard slot */
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc3>;
-};
-
-&usdhc4 { /* eMMC */
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc4>;
-	bus-width = <8>;
-	non-removable;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi b/arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi
deleted file mode 100644
index ac34709e9741..000000000000
--- a/arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi
+++ /dev/null
@@ -1,582 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0 OR X11
-/*
- * Copyright 2015 Boundary Devices, Inc.
- */
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-
-/ {
-	chosen {
-		stdout-path = &uart2;
-	};
-
-	memory@10000000 {
-		device_type = "memory";
-		reg = <0x10000000 0x20000000>;
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_2p5v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "2P5V";
-			regulator-min-microvolt = <2500000>;
-			regulator-max-microvolt = <2500000>;
-			regulator-always-on;
-		};
-
-		reg_3p3v: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-		reg_usb_otg_vbus: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
-
-		reg_wlan_vmmc: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_wlan_vmmc>;
-			regulator-name = "reg_wlan_vmmc";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			gpio = <&gpio6 7 GPIO_ACTIVE_HIGH>;
-			startup-delay-us = <70000>;
-			enable-active-high;
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpio_keys>;
-
-		home {
-			label = "Home";
-			gpios = <&gpio7 13 IRQ_TYPE_LEVEL_LOW>;
-			linux,code = <102>;
-		};
-
-		back {
-			label = "Back";
-			gpios = <&gpio4 5 IRQ_TYPE_LEVEL_LOW>;
-			linux,code = <158>;
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_leds>;
-
-		j14-pin1 {
-			gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
-			retain-state-suspended;
-			default-state = "off";
-		};
-
-		j14-pin3 {
-			gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
-			retain-state-suspended;
-			default-state = "off";
-		};
-
-		j14-pins8-9 {
-			gpios = <&gpio3 29 GPIO_ACTIVE_LOW>;
-			retain-state-suspended;
-			default-state = "off";
-		};
-
-		j46-pin2 {
-			gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
-			retain-state-suspended;
-			default-state = "off";
-		};
-
-		j46-pin3 {
-			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
-			retain-state-suspended;
-			default-state = "off";
-		};
-	};
-
-	backlight-lcd {
-		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <7>;
-		power-supply = <&reg_3p3v>;
-		status = "okay";
-	};
-
-	backlight_lvds0: backlight-lvds0 {
-		compatible = "pwm-backlight";
-		pwms = <&pwm4 0 5000000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <7>;
-		power-supply = <&reg_3p3v>;
-		status = "okay";
-	};
-
-	panel-lvds0 {
-		compatible = "hannstar,hsd100pxn1";
-		backlight = <&backlight_lvds0>;
-
-		port {
-			panel_in_lvds0: endpoint {
-				remote-endpoint = <&lvds0_out>;
-			};
-		};
-	};
-
-	sound {
-		compatible = "fsl,imx6dl-nit6xlite-sgtl5000",
-			     "fsl,imx-audio-sgtl5000";
-		model = "imx6dl-nit6xlite-sgtl5000";
-		ssi-controller = <&ssi1>;
-		audio-codec = <&codec>;
-		audio-routing =
-			"MIC_IN", "Mic Jack",
-			"Mic Jack", "Mic Bias",
-			"Headphone Jack", "HP_OUT";
-		mux-int-port = <1>;
-		mux-ext-port = <3>;
-	};
-};
-
-&audmux {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_audmux>;
-	status = "okay";
-};
-
-&clks {
-	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
-			  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
-	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
-				 <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
-};
-
-&ecspi1 {
-	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi1>;
-	status = "okay";
-
-	flash: m25p80@0 {
-		compatible = "microchip,sst25vf016b";
-		spi-max-frequency = <20000000>;
-		reg = <0>;
-	};
-};
-
-&fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
-	phy-handle = <&ethphy>;
-	phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
-	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
-			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
-	fsl,err006687-workaround-present;
-	status = "okay";
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		ethphy: ethernet-phy {
-			compatible = "ethernet-phy-ieee802.3-c22";
-			txen-skew-ps = <0>;
-			txc-skew-ps = <3000>;
-			rxdv-skew-ps = <0>;
-			rxc-skew-ps = <3000>;
-			rxd0-skew-ps = <0>;
-			rxd1-skew-ps = <0>;
-			rxd2-skew-ps = <0>;
-			rxd3-skew-ps = <0>;
-			txd0-skew-ps = <0>;
-			txd1-skew-ps = <0>;
-			txd2-skew-ps = <0>;
-			txd3-skew-ps = <0>;
-		};
-	};
-};
-
-&hdmi {
-	ddc-i2c-bus = <&i2c2>;
-	status = "okay";
-};
-
-&i2c1 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c1>;
-	status = "okay";
-
-	codec: sgtl5000@a {
-		compatible = "fsl,sgtl5000";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_sgtl5000>;
-		reg = <0x0a>;
-		clocks = <&clks IMX6QDL_CLK_CKO>;
-		VDDA-supply = <&reg_2p5v>;
-		VDDIO-supply = <&reg_3p3v>;
-	};
-};
-
-&i2c2 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c2>;
-	status = "okay";
-};
-
-&i2c3 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c3>;
-	status = "okay";
-
-	touchscreen@4 {
-		compatible = "eeti,egalax_ts";
-		reg = <0x04>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
-		wakeup-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
-	};
-
-	touchscreen@38 {
-		compatible = "edt,edt-ft5x06";
-		reg = <0x38>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
-		wakeup-source;
-	};
-
-	rtc@6f {
-		compatible = "isil,isl1208";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_rtc>;
-		reg = <0x6f>;
-		interrupts-extended = <&gpio2 26 IRQ_TYPE_LEVEL_LOW>;
-	};
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_j10>;
-	pinctrl-1 = <&pinctrl_j28>;
-
-	imx6dl-nit6xlite {
-		pinctrl_audmux: audmuxgrp {
-			fsl,pins = <
-				MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
-				MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
-				MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
-				MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
-			>;
-		};
-
-		pinctrl_ecspi1: ecspi1grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
-				MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
-				MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
-				MX6QDL_PAD_EIM_D19__GPIO3_IO19		0x000b1
-			>;
-		};
-
-		pinctrl_enet: enetgrp {
-			fsl,pins = <
-				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x100b0
-				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x100b0
-				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x100b0
-				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x100b0
-				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x100b0
-				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x100b0
-				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x100b0
-				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x100b0
-				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x100b0
-				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
-				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
-				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
-				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
-				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
-				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
-				/* Phy reset */
-				MX6QDL_PAD_ENET_RXD0__GPIO1_IO27	0x0f0b0
-				MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28	0x1b0b0
-				MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
-			>;
-		};
-
-		pinctrl_gpio_keys: gpio-keysgrp {
-			fsl,pins = <
-				/* Home Button: J14 pin 5 */
-				MX6QDL_PAD_GPIO_18__GPIO7_IO13		0x1b0b0
-				/* Back Button: J14 pin 7 */
-				MX6QDL_PAD_GPIO_19__GPIO4_IO05		0x1b0b0
-			>;
-		};
-
-		pinctrl_i2c1: i2c1grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D21__I2C1_SCL	0x4001b8b1
-				MX6QDL_PAD_EIM_D28__I2C1_SDA	0x4001b8b1
-			>;
-		};
-
-		pinctrl_i2c2: i2c2grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL3__I2C2_SCL	0x4001b8b1
-				MX6QDL_PAD_KEY_ROW3__I2C2_SDA	0x4001b8b1
-			>;
-		};
-
-		pinctrl_i2c3: i2c3grp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_5__I2C3_SCL	0x4001b8b1
-				MX6QDL_PAD_GPIO_16__I2C3_SDA	0x4001b8b1
-				/* Touch IRQ: J7 pin 4 */
-				MX6QDL_PAD_GPIO_9__GPIO1_IO09	0x1b0b0
-				/* tcs2004 IRQ */
-				MX6QDL_PAD_EIM_LBA__GPIO2_IO27	0x1b0b0
-				/* tsc2004 reset */
-				MX6QDL_PAD_KEY_COL2__GPIO4_IO10	0x0b0b0
-			>;
-		};
-
-		pinctrl_j10: j10grp {
-			fsl,pins = <
-				/* Broadcom WiFi module pins */
-				MX6QDL_PAD_NANDF_D0__GPIO2_IO00		0x1b0b0
-				MX6QDL_PAD_NANDF_D1__GPIO2_IO01		0x1b0b0
-				MX6QDL_PAD_NANDF_D3__GPIO2_IO03		0x1b0b0
-				MX6QDL_PAD_NANDF_D4__GPIO2_IO04		0x1b0b0
-				MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09	0x0b0b0
-				MX6QDL_PAD_NANDF_CS1__GPIO6_IO14	0x1b0b0
-				MX6QDL_PAD_SD1_CLK__OSC32K_32K_OUT	0x000b0
-			>;
-		};
-
-		pinctrl_j28: j28grp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1b0b0
-			>;
-		};
-
-		pinctrl_leds: ledsgrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x0b0b0
-				MX6QDL_PAD_GPIO_3__GPIO1_IO03		0x0b0b0
-				MX6QDL_PAD_EIM_D29__GPIO3_IO29		0x030b0
-				MX6QDL_PAD_GPIO_7__GPIO1_IO07		0x0b0b0
-				MX6QDL_PAD_GPIO_8__GPIO1_IO08		0x0b0b0
-			>;
-		};
-
-		pinctrl_pwm1: pwm1grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_DAT3__PWM1_OUT		0x1b0b1
-			>;
-		};
-
-		pinctrl_pwm3: pwm3grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_DAT1__PWM3_OUT		0x1b0b1
-			>;
-		};
-
-		pinctrl_pwm4: pwm4grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_CMD__PWM4_OUT		0x1b0b1
-			>;
-		};
-
-		pinctrl_wlan_vmmc: wlan-vmmcgrp {
-			fsl,pins = <
-				MX6QDL_PAD_NANDF_CLE__GPIO6_IO07	0x030b0
-			>;
-		};
-
-		pinctrl_rtc: rtcgrp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_RW__GPIO2_IO26		0x1b0b0
-			>;
-		};
-
-		pinctrl_sgtl5000: sgtl5000grp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_0__CCM_CLKO1		0x000b0
-				MX6QDL_PAD_EIM_A25__GPIO5_IO02		0x1b0b0
-			>;
-		};
-
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
-				MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA	0x1b0b1
-			>;
-		};
-
-		pinctrl_uart2: uart2grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D26__UART2_TX_DATA	0x1b0b1
-				MX6QDL_PAD_EIM_D27__UART2_RX_DATA	0x1b0b1
-			>;
-		};
-
-		pinctrl_uart3: uart3grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
-				MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
-				MX6QDL_PAD_EIM_D23__UART3_CTS_B		0x1b0b1
-				MX6QDL_PAD_EIM_D31__UART3_RTS_B		0x1b0b1
-			>;
-		};
-
-		pinctrl_usbotg: usbotggrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
-				MX6QDL_PAD_KEY_COL4__USB_OTG_OC		0x1b0b0
-				/* power enable, high active */
-				MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x000b0
-			>;
-		};
-
-		pinctrl_usdhc2: usdhc2grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
-				MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
-				MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
-				MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
-				MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
-				MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
-			>;
-		};
-
-		pinctrl_usdhc3: usdhc3grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
-				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
-				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
-				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
-				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
-				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
-				MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x1b0b0
-			>;
-		};
-	};
-};
-
-&ldb {
-	status = "okay";
-
-	lvds-channel@0 {
-		status = "okay";
-
-		port@4 {
-			reg = <4>;
-
-			lvds0_out: endpoint {
-				remote-endpoint = <&panel_in_lvds0>;
-			};
-		};
-	};
-};
-
-&pcie {
-	status = "okay";
-};
-
-&pwm1 {
-	#pwm-cells = <2>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm1>;
-	status = "okay";
-};
-
-&pwm3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm3>;
-	status = "okay";
-};
-
-&pwm4 {
-	#pwm-cells = <2>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm4>;
-	status = "okay";
-};
-
-&ssi1 {
-	status = "okay";
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
-	status = "okay";
-};
-
-&uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
-	status = "okay";
-};
-
-&uart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart3>;
-	uart-has-rtscts;
-	status = "okay";
-};
-
-&usbh1 {
-	status = "okay";
-};
-
-&usbotg {
-	vbus-supply = <&reg_usb_otg_vbus>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbotg>;
-	disable-over-current;
-	status = "okay";
-};
-
-&usdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc2>;
-	bus-width = <4>;
-	non-removable;
-	vmmc-supply = <&reg_3p3v>;
-	vqmmc-supply = <&reg_wlan_vmmc>;
-	cap-power-off-card;
-	keep-power-in-suspend;
-	status = "okay";
-};
-
-&usdhc3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc3>;
-	cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
-	vmmc-supply = <&reg_3p3v>;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi b/arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi
deleted file mode 100644
index c96f4d7e1e0d..000000000000
--- a/arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi
+++ /dev/null
@@ -1,848 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0 OR X11
-/*
- * Copyright 2015 Boundary Devices, Inc.
- */
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-
-/ {
-	chosen {
-		stdout-path = &uart2;
-	};
-
-	memory@10000000 {
-		device_type = "memory";
-		reg = <0x10000000 0xF0000000>;
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_1p8v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "1P8V";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-always-on;
-		};
-
-		reg_2p5v: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "2P5V";
-			regulator-min-microvolt = <2500000>;
-			regulator-max-microvolt = <2500000>;
-			regulator-always-on;
-		};
-
-		reg_3p3v: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-		reg_usb_otg_vbus: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
-
-		reg_usb_h1_vbus: regulator@4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_usbh1>;
-			regulator-name = "usb_h1_vbus";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
-
-		reg_wlan_vmmc: regulator@5 {
-			compatible = "regulator-fixed";
-			reg = <5>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_wlan_vmmc>;
-			regulator-name = "reg_wlan_vmmc";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio6 15 GPIO_ACTIVE_HIGH>;
-			startup-delay-us = <70000>;
-			enable-active-high;
-		};
-
-		reg_can_xcvr: regulator@6 {
-			compatible = "regulator-fixed";
-			reg = <6>;
-			regulator-name = "CAN XCVR";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_can_xcvr>;
-			gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpio_keys>;
-
-		power {
-			label = "Power Button";
-			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_POWER>;
-			wakeup-source;
-		};
-
-		menu {
-			label = "Menu";
-			gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_MENU>;
-		};
-
-		home {
-			label = "Home";
-			gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_HOME>;
-		};
-
-		back {
-			label = "Back";
-			gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_BACK>;
-		};
-
-		volume-up {
-			label = "Volume Up";
-			gpios = <&gpio7 13 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEUP>;
-		};
-
-		volume-down {
-			label = "Volume Down";
-			gpios = <&gpio7 1 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEDOWN>;
-		};
-	};
-
-	i2c2mux {
-		compatible = "i2c-mux-gpio";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_i2c2mux>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		mux-gpios = <&gpio3 20 GPIO_ACTIVE_HIGH
-			     &gpio4 15 GPIO_ACTIVE_HIGH>;
-		i2c-parent = <&i2c2>;
-		idle-state = <0>;
-
-		i2c2mux@1 {
-			reg = <1>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		i2c2mux@2 {
-			reg = <2>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-	};
-
-	i2c3mux {
-		compatible = "i2c-mux-gpio";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_i2c3mux>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		mux-gpios = <&gpio2 25 GPIO_ACTIVE_HIGH>;
-		i2c-parent = <&i2c3>;
-		idle-state = <0>;
-
-		i2c3mux@1 {
-			reg = <1>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		speaker-enable {
-			gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
-			retain-state-suspended;
-			default-state = "off";
-		};
-
-		ttymxc4-rs232 {
-			gpios = <&gpio6 10 GPIO_ACTIVE_HIGH>;
-			retain-state-suspended;
-			default-state = "on";
-		};
-	};
-
-	backlight_lcd: backlight-lcd {
-		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <7>;
-		power-supply = <&reg_3p3v>;
-		status = "okay";
-	};
-
-	backlight_lvds0: backlight-lvds0 {
-		compatible = "pwm-backlight";
-		pwms = <&pwm4 0 5000000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <7>;
-		power-supply = <&reg_3p3v>;
-		status = "okay";
-	};
-
-	backlight_lvds1: backlight-lvds1 {
-		compatible = "pwm-backlight";
-		pwms = <&pwm2 0 5000000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <7>;
-		power-supply = <&reg_3p3v>;
-		status = "okay";
-	};
-
-	lcd_display: disp0 {
-		compatible = "fsl,imx-parallel-display";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		interface-pix-fmt = "bgr666";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_j15>;
-		status = "okay";
-
-		port@0 {
-			reg = <0>;
-
-			lcd_display_in: endpoint {
-				remote-endpoint = <&ipu1_di0_disp0>;
-			};
-		};
-
-		port@1 {
-			reg = <1>;
-
-			lcd_display_out: endpoint {
-				remote-endpoint = <&lcd_panel_in>;
-			};
-		};
-	};
-
-	panel-lcd {
-		compatible = "okaya,rs800480t-7x0gp";
-		backlight = <&backlight_lcd>;
-
-		port {
-			lcd_panel_in: endpoint {
-				remote-endpoint = <&lcd_display_out>;
-			};
-		};
-	};
-
-	panel-lvds0 {
-		compatible = "hannstar,hsd100pxn1";
-		backlight = <&backlight_lvds0>;
-
-		port {
-			panel_in_lvds0: endpoint {
-				remote-endpoint = <&lvds0_out>;
-			};
-		};
-	};
-
-	panel-lvds1 {
-		compatible = "hannstar,hsd100pxn1";
-		backlight = <&backlight_lvds1>;
-
-		port {
-			panel_in_lvds1: endpoint {
-				remote-endpoint = <&lvds1_out>;
-			};
-		};
-	};
-
-	sound {
-		compatible = "fsl,imx6q-nitrogen6_max-sgtl5000",
-			     "fsl,imx-audio-sgtl5000";
-		model = "imx6q-nitrogen6_max-sgtl5000";
-		ssi-controller = <&ssi1>;
-		audio-codec = <&codec>;
-		audio-routing =
-			"MIC_IN", "Mic Jack",
-			"Mic Jack", "Mic Bias",
-			"Headphone Jack", "HP_OUT";
-		mux-int-port = <1>;
-		mux-ext-port = <3>;
-	};
-};
-
-&audmux {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_audmux>;
-	status = "okay";
-};
-
-&can1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_can1>;
-	xceiver-supply = <&reg_can_xcvr>;
-	status = "okay";
-};
-
-&clks {
-	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
-			  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
-	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
-				 <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
-};
-
-&ecspi1 {
-	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi1>;
-	status = "okay";
-
-	flash: m25p80@0 {
-		compatible = "microchip,sst25vf016b";
-		spi-max-frequency = <20000000>;
-		reg = <0>;
-	};
-};
-
-&fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
-	phy-handle = <&ethphy>;
-	phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
-	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
-			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
-	fsl,err006687-workaround-present;
-	status = "okay";
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		ethphy: ethernet-phy {
-			compatible = "ethernet-phy-ieee802.3-c22";
-			txen-skew-ps = <0>;
-			txc-skew-ps = <3000>;
-			rxdv-skew-ps = <0>;
-			rxc-skew-ps = <3000>;
-			rxd0-skew-ps = <0>;
-			rxd1-skew-ps = <0>;
-			rxd2-skew-ps = <0>;
-			rxd3-skew-ps = <0>;
-			txd0-skew-ps = <0>;
-			txd1-skew-ps = <0>;
-			txd2-skew-ps = <0>;
-			txd3-skew-ps = <0>;
-		};
-	};
-};
-
-&hdmi {
-	ddc-i2c-bus = <&i2c2>;
-	status = "okay";
-};
-
-&i2c1 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c1>;
-	status = "okay";
-
-	codec: sgtl5000@a {
-		compatible = "fsl,sgtl5000";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_sgtl5000>;
-		reg = <0x0a>;
-		clocks = <&clks IMX6QDL_CLK_CKO>;
-		VDDA-supply = <&reg_2p5v>;
-		VDDIO-supply = <&reg_3p3v>;
-	};
-
-	rtc: rtc@68 {
-		compatible = "microcrystal,rv4162";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_rv4162>;
-		reg = <0x68>;
-		interrupts-extended = <&gpio4 6 IRQ_TYPE_LEVEL_LOW>;
-	};
-};
-
-&i2c2 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c2>;
-	status = "okay";
-};
-
-&i2c3 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c3>;
-	status = "okay";
-
-	touchscreen@4 {
-		compatible = "eeti,egalax_ts";
-		reg = <0x04>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
-		wakeup-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
-	};
-
-	touchscreen@38 {
-		compatible = "edt,edt-ft5x06";
-		reg = <0x38>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
-		wakeup-source;
-	};
-};
-
-&iomuxc {
-	imx6q-nitrogen6-max {
-		pinctrl_audmux: audmuxgrp {
-			fsl,pins = <
-				MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
-				MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
-				MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
-				MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
-			>;
-		};
-
-		pinctrl_can1: can1grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b0
-				MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX	0x1b0b0
-			>;
-		};
-
-		pinctrl_can_xcvr: can-xcvrgrp {
-			fsl,pins = <
-				/* Flexcan XCVR enable */
-				MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1b0b0
-			>;
-		};
-
-		pinctrl_ecspi1: ecspi1grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
-				MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
-				MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
-				MX6QDL_PAD_EIM_D19__GPIO3_IO19		0x000b1
-			>;
-		};
-
-		pinctrl_enet: enetgrp {
-			fsl,pins = <
-				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x100b0
-				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x100b0
-				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x10030
-				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x10030
-				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x10030
-				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x10030
-				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x10030
-				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x10030
-				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x100b0
-				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
-				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
-				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
-				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
-				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
-				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
-				/* Phy reset */
-				MX6QDL_PAD_ENET_RXD0__GPIO1_IO27	0x0f0b0
-				MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28	0x1b0b0
-				MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
-			>;
-		};
-
-		pinctrl_gpio_keys: gpio-keysgrp {
-			fsl,pins = <
-				/* Power Button */
-				MX6QDL_PAD_NANDF_D3__GPIO2_IO03		0x1b0b0
-				/* Menu Button */
-				MX6QDL_PAD_NANDF_D1__GPIO2_IO01		0x1b0b0
-				/* Home Button */
-				MX6QDL_PAD_NANDF_D4__GPIO2_IO04		0x1b0b0
-				/* Back Button */
-				MX6QDL_PAD_NANDF_D2__GPIO2_IO02		0x1b0b0
-				/* Volume Up Button */
-				MX6QDL_PAD_GPIO_18__GPIO7_IO13		0x1b0b0
-				/* Volume Down Button */
-				MX6QDL_PAD_SD3_DAT4__GPIO7_IO01		0x1b0b0
-			>;
-		};
-
-		pinctrl_i2c1: i2c1grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D21__I2C1_SCL	0x4001b8b1
-				MX6QDL_PAD_EIM_D28__I2C1_SDA	0x4001b8b1
-			>;
-		};
-
-		pinctrl_i2c2: i2c2grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL3__I2C2_SCL	0x4001b8b1
-				MX6QDL_PAD_KEY_ROW3__I2C2_SDA	0x4001b8b1
-			>;
-		};
-
-		pinctrl_i2c2mux: i2c2muxgrp {
-			fsl,pins = <
-				/* ov5642 camera i2c enable */
-				MX6QDL_PAD_EIM_D20__GPIO3_IO20	0x000b0
-				/* ov5640_mipi camera i2c enable */
-				MX6QDL_PAD_KEY_ROW4__GPIO4_IO15	0x000b0
-			>;
-		};
-
-		pinctrl_i2c3: i2c3grp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_5__I2C3_SCL	0x4001b8b1
-				MX6QDL_PAD_GPIO_16__I2C3_SDA	0x4001b8b1
-				MX6QDL_PAD_GPIO_9__GPIO1_IO09	0x1b0b0
-			>;
-		};
-
-		pinctrl_i2c3mux: i2c3muxgrp {
-			fsl,pins = <
-				/* PCIe I2C enable */
-				MX6QDL_PAD_EIM_OE__GPIO2_IO25	0x000b0
-			>;
-		};
-
-		pinctrl_j15: j15grp {
-			fsl,pins = <
-				MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
-				MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15       0x10
-				MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02        0x10
-				MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03        0x10
-				MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00   0x10
-				MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01   0x10
-				MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02   0x10
-				MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03   0x10
-				MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04   0x10
-				MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05   0x10
-				MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06   0x10
-				MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07   0x10
-				MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08   0x10
-				MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09   0x10
-				MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10  0x10
-				MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11  0x10
-				MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12  0x10
-				MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13  0x10
-				MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14  0x10
-				MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15  0x10
-				MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16  0x10
-				MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17  0x10
-				MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18  0x10
-				MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19  0x10
-				MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20  0x10
-				MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21  0x10
-				MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22  0x10
-				MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23  0x10
-			>;
-		};
-
-		pinctrl_pcie: pciegrp {
-			fsl,pins = <
-				/* PCIe reset */
-				MX6QDL_PAD_EIM_BCLK__GPIO6_IO31	0x000b0
-			>;
-		};
-
-		pinctrl_pwm1: pwm1grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_DAT3__PWM1_OUT	0x1b0b1
-			>;
-		};
-
-		pinctrl_pwm2: pwm2grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_DAT2__PWM2_OUT	0x1b0b1
-			>;
-		};
-
-		pinctrl_pwm3: pwm3grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_DAT1__PWM3_OUT	0x1b0b1
-			>;
-		};
-
-		pinctrl_pwm4: pwm4grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_CMD__PWM4_OUT	0x1b0b1
-			>;
-		};
-
-		pinctrl_rv4162: rv4162grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL0__GPIO4_IO06	0x1b0b0
-			>;
-		};
-
-		pinctrl_sgtl5000: sgtl5000grp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_0__CCM_CLKO1		0x000b0
-				MX6QDL_PAD_EIM_A25__GPIO5_IO02		0x1b0b0
-				MX6QDL_PAD_ENET_TXD1__GPIO1_IO29	0x1b0b0
-			>;
-		};
-
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
-				MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA	0x1b0b1
-			>;
-		};
-
-		pinctrl_uart2: uart2grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D26__UART2_TX_DATA	0x1b0b1
-				MX6QDL_PAD_EIM_D27__UART2_RX_DATA	0x1b0b1
-			>;
-		};
-
-		pinctrl_uart5: uart5grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA	0x130b1
-				MX6QDL_PAD_KEY_COL1__UART5_TX_DATA	0x030b1
-				/* RS485 RX Enable: pull up */
-				MX6QDL_PAD_NANDF_RB0__GPIO6_IO10	0x1b0b1
-				/* RS485 DEN: pull down */
-				MX6QDL_PAD_NANDF_CLE__GPIO6_IO07	0x030b1
-				/* RS485/!RS232 Select: pull down (rs232) */
-				MX6QDL_PAD_EIM_CS1__GPIO2_IO24		0x030b1
-				/* ON: pull down */
-				MX6QDL_PAD_NANDF_ALE__GPIO6_IO08	0x030b1
-			>;
-		};
-
-		pinctrl_usbh1: usbh1grp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_17__GPIO7_IO12		0x0b0b0
-			>;
-		};
-
-		pinctrl_usbotg: usbotggrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
-				MX6QDL_PAD_KEY_COL4__USB_OTG_OC		0x1b0b0
-				/* power enable, high active */
-				MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x000b0
-			>;
-		};
-
-		pinctrl_usdhc2: usdhc2grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
-				MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
-				MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
-				MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
-				MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
-				MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
-			>;
-		};
-
-		pinctrl_usdhc3: usdhc3grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
-				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
-				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
-				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
-				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
-				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
-				MX6QDL_PAD_NANDF_CS1__SD3_VSELECT	0x100b0
-				MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x1b0b0
-			>;
-		};
-
-		pinctrl_usdhc4: usdhc4grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
-				MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
-				MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
-				MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
-				MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
-				MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059
-				MX6QDL_PAD_SD4_DAT4__SD4_DATA4		0x17059
-				MX6QDL_PAD_SD4_DAT5__SD4_DATA5		0x17059
-				MX6QDL_PAD_SD4_DAT6__SD4_DATA6		0x17059
-				MX6QDL_PAD_SD4_DAT7__SD4_DATA7		0x17059
-			>;
-		};
-
-		pinctrl_wlan_vmmc: wlan-vmmcgrp {
-			fsl,pins = <
-				MX6QDL_PAD_NANDF_CS0__GPIO6_IO11	0x100b0
-				MX6QDL_PAD_NANDF_CS2__GPIO6_IO15	0x000b0
-				MX6QDL_PAD_NANDF_CS3__GPIO6_IO16	0x000b0
-				MX6QDL_PAD_SD1_CLK__OSC32K_32K_OUT	0x000b0
-			>;
-		};
-	};
-};
-
-&ipu1_di0_disp0 {
-	remote-endpoint = <&lcd_display_in>;
-};
-
-&ldb {
-	status = "okay";
-
-	lvds-channel@0 {
-		status = "okay";
-
-		port@4 {
-			reg = <4>;
-
-			lvds0_out: endpoint {
-				remote-endpoint = <&panel_in_lvds0>;
-			};
-		};
-	};
-
-	lvds-channel@1 {
-		status = "okay";
-
-		port@4 {
-			reg = <4>;
-
-			lvds1_out: endpoint {
-				remote-endpoint = <&panel_in_lvds1>;
-			};
-		};
-	};
-};
-
-&pcie {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pcie>;
-	reset-gpio = <&gpio6 31 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-&pwm1 {
-	#pwm-cells = <2>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm1>;
-	status = "okay";
-};
-
-&pwm2 {
-	#pwm-cells = <2>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm2>;
-	status = "okay";
-};
-
-&pwm3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm3>;
-	status = "okay";
-};
-
-&pwm4 {
-	#pwm-cells = <2>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm4>;
-	status = "okay";
-};
-
-&ssi1 {
-	status = "okay";
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
-	status = "okay";
-};
-
-&uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
-	status = "okay";
-};
-
-&uart5 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart5>;
-	status = "okay";
-};
-
-&usbh1 {
-	vbus-supply = <&reg_usb_h1_vbus>;
-	status = "okay";
-};
-
-&usbotg {
-	vbus-supply = <&reg_usb_otg_vbus>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbotg>;
-	disable-over-current;
-	status = "okay";
-};
-
-&usdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc2>;
-	bus-width = <4>;
-	non-removable;
-	vmmc-supply = <&reg_wlan_vmmc>;
-	cap-power-off-card;
-	keep-power-in-suspend;
-	status = "okay";
-
-	#address-cells = <1>;
-	#size-cells = <0>;
-	wlcore: wlcore@2 {
-		compatible = "ti,wl1271";
-		reg = <2>;
-		interrupt-parent = <&gpio6>;
-		interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
-		ref-clock-frequency = <38400000>;
-	};
-};
-
-&usdhc3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc3>;
-	cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
-	bus-width = <4>;
-	vmmc-supply = <&reg_3p3v>;
-	status = "okay";
-};
-
-&usdhc4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc4>;
-	bus-width = <8>;
-	non-removable;
-	vmmc-supply = <&reg_1p8v>;
-	keep-power-in-suspend;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi b/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi
deleted file mode 100644
index 49da30d7510c..000000000000
--- a/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi
+++ /dev/null
@@ -1,692 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0 OR X11
-/*
- * Copyright 2013 Boundary Devices, Inc.
- * Copyright 2011 Freescale Semiconductor, Inc.
- * Copyright 2011 Linaro Ltd.
- */
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-
-/ {
-	chosen {
-		stdout-path = &uart2;
-	};
-
-	memory@10000000 {
-		device_type = "memory";
-		reg = <0x10000000 0x40000000>;
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_2p5v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "2P5V";
-			regulator-min-microvolt = <2500000>;
-			regulator-max-microvolt = <2500000>;
-			regulator-always-on;
-		};
-
-		reg_3p3v: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-		reg_usb_otg_vbus: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 22 0>;
-			enable-active-high;
-		};
-
-		reg_can_xcvr: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "CAN XCVR";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_can_xcvr>;
-			gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
-		};
-
-		reg_wlan_vmmc: regulator@4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_wlan_vmmc>;
-			regulator-name = "reg_wlan_vmmc";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio6 15 GPIO_ACTIVE_HIGH>;
-			startup-delay-us = <70000>;
-			enable-active-high;
-		};
-
-		reg_usb_h1_vbus: regulator@5 {
-			compatible = "regulator-fixed";
-			reg = <5>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_usbh1>;
-			regulator-name = "usb_h1_vbus";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpio_keys>;
-
-		power {
-			label = "Power Button";
-			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_POWER>;
-			wakeup-source;
-		};
-
-		menu {
-			label = "Menu";
-			gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_MENU>;
-		};
-
-		home {
-			label = "Home";
-			gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_HOME>;
-		};
-
-		back {
-			label = "Back";
-			gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_BACK>;
-		};
-
-		volume-up {
-			label = "Volume Up";
-			gpios = <&gpio7 13 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEUP>;
-		};
-
-		volume-down {
-			label = "Volume Down";
-			gpios = <&gpio4 5 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEDOWN>;
-		};
-	};
-
-	sound {
-		compatible = "fsl,imx6q-nitrogen6x-sgtl5000",
-			     "fsl,imx-audio-sgtl5000";
-		model = "imx6q-nitrogen6x-sgtl5000";
-		ssi-controller = <&ssi1>;
-		audio-codec = <&codec>;
-		audio-routing =
-			"MIC_IN", "Mic Jack",
-			"Mic Jack", "Mic Bias",
-			"Headphone Jack", "HP_OUT";
-		mux-int-port = <1>;
-		mux-ext-port = <3>;
-	};
-
-	backlight_lcd: backlight-lcd {
-		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <7>;
-		power-supply = <&reg_3p3v>;
-		status = "okay";
-	};
-
-	backlight_lvds: backlight-lvds {
-		compatible = "pwm-backlight";
-		pwms = <&pwm4 0 5000000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <7>;
-		power-supply = <&reg_3p3v>;
-		status = "okay";
-	};
-
-	lcd_display: disp0 {
-		compatible = "fsl,imx-parallel-display";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		interface-pix-fmt = "bgr666";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_j15>;
-		status = "okay";
-
-		port@0 {
-			reg = <0>;
-
-			lcd_display_in: endpoint {
-				remote-endpoint = <&ipu1_di0_disp0>;
-			};
-		};
-
-		port@1 {
-			reg = <1>;
-
-			lcd_display_out: endpoint {
-				remote-endpoint = <&lcd_panel_in>;
-			};
-		};
-	};
-
-	panel-lcd {
-		compatible = "okaya,rs800480t-7x0gp";
-		backlight = <&backlight_lcd>;
-
-		port {
-			lcd_panel_in: endpoint {
-				remote-endpoint = <&lcd_display_out>;
-			};
-		};
-	};
-
-	panel-lvds0 {
-		compatible = "hannstar,hsd100pxn1";
-		backlight = <&backlight_lvds>;
-
-		port {
-			panel_in: endpoint {
-				remote-endpoint = <&lvds0_out>;
-			};
-		};
-	};
-};
-
-&audmux {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_audmux>;
-	status = "okay";
-};
-
-&can1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_can1>;
-	xceiver-supply = <&reg_can_xcvr>;
-	status = "okay";
-};
-
-&clks {
-	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
-			  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
-	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
-				 <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
-};
-
-&ecspi1 {
-	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi1>;
-	status = "okay";
-
-	flash: m25p80@0 {
-		compatible = "sst,sst25vf016b", "jedec,spi-nor";
-		spi-max-frequency = <20000000>;
-		reg = <0>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-
-		partition@0 {
-			label = "bootloader";
-			reg = <0x0 0xc0000>;
-		};
-
-		partition@c0000 {
-			label = "env";
-			reg = <0xc0000 0x2000>;
-		};
-
-		partition@c2000 {
-			label = "splash";
-			reg = <0xc2000 0x13e000>;
-		};
-	};
-};
-
-&fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
-	phy-handle = <&ethphy>;
-	phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
-	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
-			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
-	fsl,err006687-workaround-present;
-	status = "okay";
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		ethphy: ethernet-phy {
-			compatible = "ethernet-phy-ieee802.3-c22";
-			txen-skew-ps = <0>;
-			txc-skew-ps = <3000>;
-			rxdv-skew-ps = <0>;
-			rxc-skew-ps = <3000>;
-			rxd0-skew-ps = <0>;
-			rxd1-skew-ps = <0>;
-			rxd2-skew-ps = <0>;
-			rxd3-skew-ps = <0>;
-			txd0-skew-ps = <0>;
-			txd1-skew-ps = <0>;
-			txd2-skew-ps = <0>;
-			txd3-skew-ps = <0>;
-		};
-	};
-};
-
-&hdmi {
-	ddc-i2c-bus = <&i2c2>;
-	status = "okay";
-};
-
-&i2c1 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c1>;
-	status = "okay";
-
-	codec: sgtl5000@a {
-		compatible = "fsl,sgtl5000";
-		reg = <0x0a>;
-		clocks = <&clks IMX6QDL_CLK_CKO>;
-		VDDA-supply = <&reg_2p5v>;
-		VDDIO-supply = <&reg_3p3v>;
-	};
-
-	rtc: rtc@6f {
-		compatible = "isil,isl1208";
-		reg = <0x6f>;
-	};
-};
-
-&i2c2 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c2>;
-	status = "okay";
-};
-
-&i2c3 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c3>;
-	status = "okay";
-
-	touchscreen@4 {
-		compatible = "eeti,egalax_ts";
-		reg = <0x04>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
-		wakeup-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
-	};
-
-	touchscreen@38 {
-		compatible = "edt,edt-ft5x06";
-		reg = <0x38>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
-		wakeup-source;
-	};
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_hog>;
-
-	imx6q-nitrogen6x {
-		pinctrl_hog: hoggrp {
-			fsl,pins = <
-				/* SGTL5000 sys_mclk */
-				MX6QDL_PAD_GPIO_0__CCM_CLKO1    0x030b0
-				MX6QDL_PAD_GPIO_9__GPIO1_IO09	0x1b0b0
-			>;
-		};
-
-		pinctrl_audmux: audmuxgrp {
-			fsl,pins = <
-				MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
-				MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
-				MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
-				MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
-			>;
-		};
-
-		pinctrl_can1: can1grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b0
-				MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX	0x1b0b0
-			>;
-		};
-
-		pinctrl_can_xcvr: can-xcvrgrp {
-			fsl,pins = <
-				/* Flexcan XCVR enable */
-				MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1b0b0
-			>;
-		};
-
-		pinctrl_ecspi1: ecspi1grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
-				MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
-				MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
-				MX6QDL_PAD_EIM_D19__GPIO3_IO19  0x000b1	/* CS */
-			>;
-		};
-
-		pinctrl_enet: enetgrp {
-			fsl,pins = <
-				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x100b0
-				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x100b0
-				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x10030
-				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x10030
-				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x10030
-				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x10030
-				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x10030
-				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x10030
-				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x100b0
-				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
-				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
-				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
-				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
-				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
-				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
-				/* Phy reset */
-				MX6QDL_PAD_ENET_RXD0__GPIO1_IO27	0x000b0
-				MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
-			>;
-		};
-
-		pinctrl_gpio_keys: gpio-keysgrp {
-			fsl,pins = <
-				/* Power Button */
-				MX6QDL_PAD_NANDF_D3__GPIO2_IO03		0x1b0b0
-				/* Menu Button */
-				MX6QDL_PAD_NANDF_D1__GPIO2_IO01		0x1b0b0
-				/* Home Button */
-				MX6QDL_PAD_NANDF_D4__GPIO2_IO04		0x1b0b0
-				/* Back Button */
-				MX6QDL_PAD_NANDF_D2__GPIO2_IO02		0x1b0b0
-				/* Volume Up Button */
-				MX6QDL_PAD_GPIO_18__GPIO7_IO13		0x1b0b0
-				/* Volume Down Button */
-				MX6QDL_PAD_GPIO_19__GPIO4_IO05		0x1b0b0
-			>;
-		};
-
-		pinctrl_i2c1: i2c1grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
-				MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
-			>;
-		};
-
-		pinctrl_i2c2: i2c2grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
-				MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
-			>;
-		};
-
-		pinctrl_i2c3: i2c3grp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_5__I2C3_SCL		0x4001b8b1
-				MX6QDL_PAD_GPIO_16__I2C3_SDA		0x4001b8b1
-			>;
-		};
-
-		pinctrl_j15: j15grp {
-			fsl,pins = <
-				MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
-				MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15       0x10
-				MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02        0x10
-				MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03        0x10
-				MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00   0x10
-				MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01   0x10
-				MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02   0x10
-				MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03   0x10
-				MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04   0x10
-				MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05   0x10
-				MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06   0x10
-				MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07   0x10
-				MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08   0x10
-				MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09   0x10
-				MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10  0x10
-				MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11  0x10
-				MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12  0x10
-				MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13  0x10
-				MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14  0x10
-				MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15  0x10
-				MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16  0x10
-				MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17  0x10
-				MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18  0x10
-				MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19  0x10
-				MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20  0x10
-				MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21  0x10
-				MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22  0x10
-				MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23  0x10
-			>;
-		};
-
-		pinctrl_pwm1: pwm1grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1
-			>;
-		};
-
-		pinctrl_pwm3: pwm3grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_DAT1__PWM3_OUT 0x1b0b1
-			>;
-		};
-
-		pinctrl_pwm4: pwm4grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1
-			>;
-		};
-
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
-				MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA	0x1b0b1
-			>;
-		};
-
-		pinctrl_uart2: uart2grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D26__UART2_TX_DATA	0x1b0b1
-				MX6QDL_PAD_EIM_D27__UART2_RX_DATA	0x1b0b1
-			>;
-		};
-
-		pinctrl_usbh1: usbh1grp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_17__GPIO7_IO12		0x030b0
-			>;
-		};
-
-		pinctrl_usbotg: usbotggrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_1__USB_OTG_ID	0x17059
-				MX6QDL_PAD_KEY_COL4__USB_OTG_OC	0x1b0b0
-				/* power enable, high active */
-				MX6QDL_PAD_EIM_D22__GPIO3_IO22  0x000b0
-			>;
-		};
-
-		pinctrl_usdhc2: usdhc2grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17071
-				MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10071
-				MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17071
-				MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17071
-				MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17071
-				MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17071
-			>;
-		};
-
-		pinctrl_usdhc3: usdhc3grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
-				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
-				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
-				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
-				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
-				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
-				MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0	/* CD */
-			>;
-		};
-
-		pinctrl_usdhc4: usdhc4grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
-				MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
-				MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
-				MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
-				MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
-				MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059
-				MX6QDL_PAD_NANDF_D6__GPIO2_IO06 0x1b0b0	/* CD */
-			>;
-		};
-
-		pinctrl_wlan_vmmc: wlan-vmmcgrp {
-			fsl,pins = <
-				MX6QDL_PAD_NANDF_CS0__GPIO6_IO11	0x100b0
-				MX6QDL_PAD_NANDF_CS2__GPIO6_IO15	0x000b0
-				MX6QDL_PAD_NANDF_CS3__GPIO6_IO16	0x000b0
-				MX6QDL_PAD_SD1_CLK__OSC32K_32K_OUT	0x000b0
-			>;
-		};
-	};
-};
-
-&ipu1_di0_disp0 {
-	remote-endpoint = <&lcd_display_in>;
-};
-
-&ldb {
-	status = "okay";
-
-	lvds-channel@0 {
-		status = "okay";
-
-		port@4 {
-			reg = <4>;
-
-			lvds0_out: endpoint {
-				remote-endpoint = <&panel_in>;
-			};
-		};
-	};
-};
-
-&pcie {
-	status = "okay";
-};
-
-&pwm1 {
-	#pwm-cells = <2>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm1>;
-	status = "okay";
-};
-
-&pwm3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm3>;
-	status = "okay";
-};
-
-&pwm4 {
-	#pwm-cells = <2>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm4>;
-	status = "okay";
-};
-
-&ssi1 {
-	status = "okay";
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
-	status = "okay";
-};
-
-&uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
-	status = "okay";
-};
-
-&usbh1 {
-	vbus-supply = <&reg_usb_h1_vbus>;
-	status = "okay";
-};
-
-&usbotg {
-	vbus-supply = <&reg_usb_otg_vbus>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbotg>;
-	disable-over-current;
-	status = "okay";
-};
-
-&usdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc2>;
-	bus-width = <4>;
-	non-removable;
-	vmmc-supply = <&reg_wlan_vmmc>;
-	cap-power-off-card;
-	keep-power-in-suspend;
-	status = "okay";
-
-	#address-cells = <1>;
-	#size-cells = <0>;
-	wlcore: wlcore@2 {
-		compatible = "ti,wl1271";
-		reg = <2>;
-		interrupt-parent = <&gpio6>;
-		interrupts = <14 IRQ_TYPE_LEVEL_HIGH>;
-		ref-clock-frequency = <38400000>;
-	};
-};
-
-&usdhc3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc3>;
-	cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
-	vmmc-supply = <&reg_3p3v>;
-	status = "okay";
-};
-
-&usdhc4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc4>;
-	cd-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
-	vmmc-supply = <&reg_3p3v>;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi
deleted file mode 100644
index 1f2ba6f6254e..000000000000
--- a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi
+++ /dev/null
@@ -1,466 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Copyright 2013 Christian Hemp, Phytec Messtechnik GmbH
- */
-
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
-	model = "Phytec phyFLEX-i.MX6 Quad";
-	compatible = "phytec,imx6q-pfla02", "fsl,imx6q";
-
-	memory@10000000 {
-		device_type = "memory";
-		reg = <0x10000000 0x80000000>;
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_usb_otg_vbus: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio4 15 0>;
-			enable-active-high;
-		};
-
-		reg_usb_h1_vbus: regulator@1 {
-			compatible = "regulator-fixed";
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_usbh1_vbus>;
-			reg = <1>;
-			regulator-name = "usb_h1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio1 0 0>;
-			enable-active-high;
-		};
-	};
-
-	gpio_leds: leds {
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_leds>;
-		compatible = "gpio-leds";
-
-		green {
-			label = "phyflex:green";
-			gpios = <&gpio1 30 0>;
-		};
-
-		red {
-			label = "phyflex:red";
-			gpios = <&gpio2 31 0>;
-		};
-	};
-};
-
-&audmux {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_audmux>;
-	status = "disabled";
-};
-
-&can1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_flexcan1>;
-	status = "disabled";
-};
-
-&ecspi3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi3>;
-	status = "okay";
-	cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
-
-	som_flash: flash@0 {
-		compatible = "m25p80", "jedec,spi-nor";
-		spi-max-frequency = <20000000>;
-		reg = <0>;
-	};
-};
-
-&fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet>;
-	phy-handle = <&ethphy>;
-	phy-mode = "rgmii";
-	phy-reset-duration = <10>; /* in msecs */
-	phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
-	phy-supply = <&vdd_eth_io_reg>;
-	status = "disabled";
-
-	fec_mdio: mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		ethphy: ethernet-phy@0 {
-			compatible = "ethernet-phy-ieee802.3-c22";
-			reg = <0>;
-			txc-skew-ps = <1680>;
-			rxc-skew-ps = <1860>;
-		};
-	};
-};
-
-&gpmi {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_gpmi_nand>;
-	nand-on-flash-bbt;
-	status = "okay";
-};
-
-&i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c1>;
-	status = "okay";
-
-	som_eeprom: eeprom@50 {
-		compatible = "catalyst,24c32", "atmel,24c32";
-		pagesize = <32>;
-		reg = <0x50>;
-	};
-
-	pmic@58 {
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_pmic>;
-		compatible = "dlg,da9063";
-		reg = <0x58>;
-		interrupt-parent = <&gpio2>;
-		interrupts = <9 IRQ_TYPE_LEVEL_LOW>; /* active-low GPIO2_9 */
-		interrupt-controller;
-
-		regulators {
-			vddcore_reg: bcore1 {
-				regulator-min-microvolt = <730000>;
-				regulator-max-microvolt = <1380000>;
-				regulator-always-on;
-			};
-
-			vddsoc_reg: bcore2 {
-				regulator-min-microvolt = <730000>;
-				regulator-max-microvolt = <1380000>;
-				regulator-always-on;
-			};
-
-			vdd_ddr3_reg: bpro {
-				regulator-min-microvolt = <1500000>;
-				regulator-max-microvolt = <1500000>;
-				regulator-always-on;
-			};
-
-			vdd_3v3_reg: bperi {
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-always-on;
-			};
-
-			vdd_buckmem_reg: bmem {
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-always-on;
-			};
-
-			vdd_eth_reg: bio {
-				regulator-min-microvolt = <1200000>;
-				regulator-max-microvolt = <1200000>;
-				regulator-always-on;
-			};
-
-			vdd_eth_io_reg: ldo4 {
-				regulator-min-microvolt = <2500000>;
-				regulator-max-microvolt = <2500000>;
-				regulator-always-on;
-			};
-
-			vdd_mx6_snvs_reg: ldo5 {
-				regulator-min-microvolt = <3000000>;
-				regulator-max-microvolt = <3000000>;
-				regulator-always-on;
-			};
-
-			vdd_3v3_pmic_io_reg: ldo6 {
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-always-on;
-			};
-
-			vdd_sd0_reg: ldo9 {
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
-			};
-
-			vdd_sd1_reg: ldo10 {
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
-			};
-
-			vdd_mx6_high_reg: ldo11 {
-				regulator-min-microvolt = <3000000>;
-				regulator-max-microvolt = <3000000>;
-				regulator-always-on;
-			};
-		};
-
-		da9063_rtc: rtc {
-			compatible = "dlg,da9063-rtc";
-		};
-
-		da9063_wdog: watchdog {
-			compatible = "dlg,da9063-watchdog";
-		};
-
-		onkey {
-			compatible = "dlg,da9063-onkey";
-			status = "disabled";
-		};
-	};
-};
-
-&i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c2>;
-	clock-frequency = <100000>;
-};
-
-&i2c3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c3>;
-	clock-frequency = <100000>;
-};
-
-&iomuxc {
-	imx6q-phytec-pfla02 {
-		pinctrl_ecspi3: ecspi3grp {
-			fsl,pins = <
-				MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO	0x100b1
-				MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI	0x100b1
-				MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK	0x100b1
-				MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24	0x80000000 /* CS0 */
-			>;
-		};
-
-		pinctrl_enet: enetgrp {
-			fsl,pins = <
-				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
-				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
-				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
-				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
-				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
-				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
-				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
-				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
-				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
-				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
-				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
-				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
-				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
-				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
-				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
-				MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN	0x1b0b0
-				MX6QDL_PAD_EIM_D23__GPIO3_IO23		0x80000000 /* Reset GPIO */
-			>;
-		};
-
-		pinctrl_flexcan1: flexcan1grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX	0x1b0b0
-				MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b0
-			>;
-		};
-
-		pinctrl_gpmi_nand: gpminandgrp {
-			fsl,pins = <
-				MX6QDL_PAD_NANDF_CLE__NAND_CLE		0xb0b1
-				MX6QDL_PAD_NANDF_ALE__NAND_ALE		0xb0b1
-				MX6QDL_PAD_NANDF_WP_B__NAND_WP_B	0xb0b1
-				MX6QDL_PAD_NANDF_RB0__NAND_READY_B	0xb000
-				MX6QDL_PAD_NANDF_CS0__NAND_CE0_B	0xb0b1
-				MX6QDL_PAD_NANDF_CS1__NAND_CE1_B	0xb0b1
-				MX6QDL_PAD_SD4_CMD__NAND_RE_B		0xb0b1
-				MX6QDL_PAD_SD4_CLK__NAND_WE_B		0xb0b1
-				MX6QDL_PAD_NANDF_D0__NAND_DATA00	0xb0b1
-				MX6QDL_PAD_NANDF_D1__NAND_DATA01	0xb0b1
-				MX6QDL_PAD_NANDF_D2__NAND_DATA02	0xb0b1
-				MX6QDL_PAD_NANDF_D3__NAND_DATA03	0xb0b1
-				MX6QDL_PAD_NANDF_D4__NAND_DATA04	0xb0b1
-				MX6QDL_PAD_NANDF_D5__NAND_DATA05	0xb0b1
-				MX6QDL_PAD_NANDF_D6__NAND_DATA06	0xb0b1
-				MX6QDL_PAD_NANDF_D7__NAND_DATA07	0xb0b1
-				MX6QDL_PAD_SD4_DAT0__NAND_DQS		0x00b1
-			>;
-		};
-
-		pinctrl_i2c1: i2c1grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
-				MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
-			>;
-		};
-
-		pinctrl_i2c2: i2c2grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_EB2__I2C2_SCL		0x4001b8b1
-				MX6QDL_PAD_EIM_D16__I2C2_SDA		0x4001b8b1
-			>;
-		};
-
-		pinctrl_i2c3: i2c3grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D17__I2C3_SCL		0x4001b8b1
-				MX6QDL_PAD_EIM_D18__I2C3_SDA		0x4001b8b1
-			>;
-		};
-
-		pinctrl_leds: ledsgrp {
-			fsl,pins = <
-				MX6QDL_PAD_ENET_TXD0__GPIO1_IO30	0x80000000 /* Green LED */
-				MX6QDL_PAD_EIM_EB3__GPIO2_IO31		0x80000000 /* Red LED */
-			>;
-		};
-
-		pinctrl_pcie: pciegrp {
-			fsl,pins = <MX6QDL_PAD_DI0_PIN15__GPIO4_IO17  0x80000000>;
-		};
-
-		pinctrl_pmic: pmicgrp {
-			fsl,pins = <MX6QDL_PAD_SD4_DAT1__GPIO2_IO09	0x80000000>; /* PMIC interrupt */
-		};
-
-		pinctrl_uart3: uart3grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
-				MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
-				MX6QDL_PAD_EIM_D31__UART3_RTS_B		0x1b0b1
-				MX6QDL_PAD_EIM_D30__UART3_CTS_B		0x1b0b1
-			>;
-		};
-
-		pinctrl_uart4: uart4grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL0__UART4_TX_DATA	0x1b0b1
-				MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA	0x1b0b1
-			>;
-		};
-
-		pinctrl_usbh1_vbus: usbh1vbusgrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_0__GPIO1_IO00		0x1b0b0
-			>;
-		};
-
-		pinctrl_usbotg: usbotggrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
-				MX6QDL_PAD_KEY_COL4__USB_OTG_OC		0x1b0b0
-				MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x80000000
-			>;
-		};
-
-		pinctrl_usdhc2: usdhc2grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
-				MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
-				MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
-				MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
-				MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
-				MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
-			>;
-		};
-
-		pinctrl_usdhc3: usdhc3grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
-				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
-				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
-				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
-				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
-				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
-			>;
-		};
-
-		pinctrl_usdhc3_cdwp: usdhc3cdwp {
-			fsl,pins = <
-				MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x80000000
-				MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x80000000
-			>;
-		};
-
-		pinctrl_audmux: audmuxgrp {
-			fsl,pins = <
-				MX6QDL_PAD_DISP0_DAT16__AUD5_TXC	0x130b0
-				MX6QDL_PAD_DISP0_DAT17__AUD5_TXD	0x110b0
-				MX6QDL_PAD_DISP0_DAT18__AUD5_TXFS	0x130b0
-				MX6QDL_PAD_DISP0_DAT19__AUD5_RXD	0x130b0
-			>;
-		};
-	};
-};
-
-&pcie {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pcie>;
-	reset-gpio = <&gpio4 17 GPIO_ACTIVE_LOW>;
-	status = "disabled";
-};
-
-&reg_arm {
-	vin-supply = <&vddcore_reg>;
-};
-
-&reg_pu {
-	vin-supply = <&vddsoc_reg>;
-};
-
-&reg_soc {
-	vin-supply = <&vddsoc_reg>;
-};
-
-&uart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart3>;
-	uart-has-rtscts;
-	status = "disabled";
-};
-
-&uart4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart4>;
-	status = "disabled";
-};
-
-&usbh1 {
-	vbus-supply = <&reg_usb_h1_vbus>;
-	status = "disabled";
-};
-
-&usbotg {
-	vbus-supply = <&reg_usb_otg_vbus>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbotg>;
-	disable-over-current;
-	status = "disabled";
-};
-
-&usdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc2>;
-	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
-	vmmc-supply = <&vdd_sd1_reg>;
-	status = "disabled";
-};
-
-&usdhc3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc3
-		     &pinctrl_usdhc3_cdwp>;
-	cd-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
-	vmmc-supply = <&vdd_sd0_reg>;
-	status = "disabled";
-};
diff --git a/arch/arm/boot/dts/imx6qdl-rex.dtsi b/arch/arm/boot/dts/imx6qdl-rex.dtsi
deleted file mode 100644
index de514eb5aa99..000000000000
--- a/arch/arm/boot/dts/imx6qdl-rex.dtsi
+++ /dev/null
@@ -1,367 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright 2014 FEDEVEL, Inc.
- *
- * Author: Robert Nelson <robertcnelson@gmail.com>
- */
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-
-/ {
-	chosen {
-		stdout-path = &uart1;
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-		reg_usbh1_vbus: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			pinctrl-names = "default";
-			regulator-name = "usbh1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
-
-		reg_usb_otg_vbus: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			pinctrl-names = "default";
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_led>;
-
-		led0: usr {
-			label = "usr";
-			gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
-			default-state = "off";
-			linux,default-trigger = "heartbeat";
-		};
-	};
-
-	sound {
-		compatible = "fsl,imx6-rex-sgtl5000",
-			     "fsl,imx-audio-sgtl5000";
-		model = "imx6-rex-sgtl5000";
-		ssi-controller = <&ssi1>;
-		audio-codec = <&codec>;
-		audio-routing =
-			"MIC_IN", "Mic Jack",
-			"Mic Jack", "Mic Bias",
-			"Headphone Jack", "HP_OUT";
-		mux-int-port = <1>;
-		mux-ext-port = <3>;
-	};
-};
-
-&audmux {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_audmux>;
-	status = "okay";
-};
-
-&ecspi2 {
-	cs-gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi2>;
-	status = "okay";
-};
-
-&ecspi3 {
-	cs-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi3>;
-	status = "okay";
-};
-
-&fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
-	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-&hdmi {
-	ddc-i2c-bus = <&i2c2>;
-	status = "okay";
-};
-
-&i2c1 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c1>;
-	status = "okay";
-
-	codec: sgtl5000@a {
-		compatible = "fsl,sgtl5000";
-		reg = <0x0a>;
-		clocks = <&clks IMX6QDL_CLK_CKO>;
-		VDDA-supply = <&reg_3p3v>;
-		VDDIO-supply = <&reg_3p3v>;
-	};
-};
-
-&i2c2 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c2>;
-	status = "okay";
-
-	pca9535: gpio-expander@27 {
-		compatible = "nxp,pca9535";
-		reg = <0x27>;
-		gpio-controller;
-		#gpio-cells = <2>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_pca9535>;
-		interrupt-parent = <&gpio6>;
-		interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-	};
-
-	eeprom@57 {
-		compatible = "atmel,24c02";
-		reg = <0x57>;
-	};
-};
-
-&i2c3 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c3>;
-	status = "okay";
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_hog>;
-
-	imx6qdl-rex {
-		pinctrl_hog: hoggrp {
-			fsl,pins = <
-				/* SGTL5000 sys_mclk */
-				MX6QDL_PAD_GPIO_0__CCM_CLKO1		0x030b0
-			>;
-		};
-
-		pinctrl_audmux: audmuxgrp {
-			fsl,pins = <
-				MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
-				MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
-				MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
-				MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
-			>;
-		};
-
-		pinctrl_ecspi2: ecspi2grp {
-			fsl,pins = <
-				MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO	0x100b1
-				MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI	0x100b1
-				MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK	0x100b1
-				/* CS */
-				MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26	0x000b1
-			>;
-		};
-
-		pinctrl_ecspi3: ecspi3grp {
-			fsl,pins = <
-				MX6QDL_PAD_DISP0_DAT17__ECSPI2_MISO	0x100b1
-				MX6QDL_PAD_DISP0_DAT16__ECSPI2_MOSI	0x100b1
-				MX6QDL_PAD_DISP0_DAT19__ECSPI2_SCLK	0x100b1
-				/* CS */
-				MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12	0x000b1
-			>;
-		};
-
-		pinctrl_enet: enetgrp {
-			fsl,pins = <
-				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
-				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
-				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
-				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
-				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
-				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
-				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
-				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
-				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
-				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
-				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
-				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
-				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
-				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
-				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
-				MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
-				/* Phy reset */
-				MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25	0x000b0
-			>;
-		};
-
-		pinctrl_i2c1: i2c1grp {
-			fsl,pins = <
-				MX6QDL_PAD_CSI0_DAT8__I2C1_SDA		0x4001b8b1
-				MX6QDL_PAD_CSI0_DAT9__I2C1_SCL		0x4001b8b1
-			>;
-		};
-
-		pinctrl_i2c2: i2c2grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
-				MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
-			>;
-		};
-
-		pinctrl_i2c3: i2c3grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D17__I2C3_SCL		0x4001b8b1
-				MX6QDL_PAD_EIM_D18__I2C3_SDA		0x4001b8b1
-			>;
-		};
-
-		pinctrl_led: ledgrp {
-			fsl,pins = <
-				/* user led */
-				MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x80000000
-			>;
-		};
-
-		pinctrl_pca9535: pca9535grp {
-			fsl,pins = <
-				MX6QDL_PAD_NANDF_CS3__GPIO6_IO16	0x17059
-		   >;
-		};
-
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0b1
-				MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0b1
-			>;
-		};
-
-		pinctrl_uart2: uart2grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA	0x1b0b1
-				MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA	0x1b0b1
-			>;
-		};
-
-		pinctrl_usbh1: usbh1grp {
-			fsl,pins = <
-				/* power enable, high active */
-				MX6QDL_PAD_EIM_D31__GPIO3_IO31		0x10b0
-			>;
-		};
-
-		pinctrl_usbotg: usbotggrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
-				MX6QDL_PAD_EIM_D21__USB_OTG_OC		0x1b0b0
-				/* power enable, high active */
-				MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x10b0
-			>;
-		};
-
-		pinctrl_usdhc2: usdhc2grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
-				MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
-				MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
-				MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
-				MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
-				MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
-				/* CD */
-				MX6QDL_PAD_NANDF_D2__GPIO2_IO02		0x1b0b0
-				/* WP */
-				MX6QDL_PAD_NANDF_D3__GPIO2_IO03		0x1f0b0
-			>;
-		};
-
-		pinctrl_usdhc3: usdhc3grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
-				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
-				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
-				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
-				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
-				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
-				/* CD */
-				MX6QDL_PAD_NANDF_D0__GPIO2_IO00		0x1b0b0
-				/* WP */
-				MX6QDL_PAD_NANDF_D1__GPIO2_IO01		0x1f0b0
-			>;
-		};
-	};
-};
-
-&ssi1 {
-	status = "okay";
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
-	status = "okay";
-};
-
-&uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
-	status = "okay";
-};
-
-&usbh1 {
-	vbus-supply = <&reg_usbh1_vbus>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbh1>;
-	status = "okay";
-};
-
-&usbotg {
-	vbus-supply = <&reg_usb_otg_vbus>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbotg>;
-	status = "okay";
-};
-
-&usdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc2>;
-	bus-width = <4>;
-	cd-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
-	status = "okay";
-};
-
-&usdhc3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc3>;
-	bus-width = <4>;
-	cd-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
deleted file mode 100644
index eb9a0b104f1c..000000000000
--- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
+++ /dev/null
@@ -1,778 +0,0 @@
-/*
- * Copyright 2011 Freescale Semiconductor, Inc.
- * Copyright 2011 Linaro Ltd.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#include <dt-bindings/clock/imx6qdl-clock.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-
-/ {
-	chosen {
-		stdout-path = &uart2;
-	};
-
-	memory@10000000 {
-		device_type = "memory";
-		reg = <0x10000000 0x40000000>;
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_2p5v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "2P5V";
-			regulator-min-microvolt = <2500000>;
-			regulator-max-microvolt = <2500000>;
-			regulator-always-on;
-		};
-
-		reg_3p3v: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-		reg_usb_otg_vbus: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 22 0>;
-			enable-active-high;
-		};
-
-		reg_can_xcvr: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "CAN XCVR";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_can_xcvr>;
-			gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
-		};
-
-		reg_1p5v: regulator@4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			regulator-name = "1P5V";
-			regulator-min-microvolt = <1500000>;
-			regulator-max-microvolt = <1500000>;
-			regulator-always-on;
-		};
-
-		reg_1p8v: regulator@5 {
-			compatible = "regulator-fixed";
-			reg = <5>;
-			regulator-name = "1P8V";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-always-on;
-		};
-
-		reg_2p8v: regulator@6 {
-			compatible = "regulator-fixed";
-			reg = <6>;
-			regulator-name = "2P8V";
-			regulator-min-microvolt = <2800000>;
-			regulator-max-microvolt = <2800000>;
-			regulator-always-on;
-		};
-
-		reg_usb_h1_vbus: regulator@7 {
-			compatible = "regulator-fixed";
-			reg = <7>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_usbh1>;
-			regulator-name = "usb_h1_vbus";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
-	};
-
-	mipi_xclk: mipi_xclk {
-		compatible = "pwm-clock";
-		#clock-cells = <0>;
-		clock-frequency = <22000000>;
-		clock-output-names = "mipi_pwm3";
-		pwms = <&pwm3 0 45>; /* 1 / 45 ns = 22 MHz */
-		status = "okay";
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpio_keys>;
-
-		power {
-			label = "Power Button";
-			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_POWER>;
-			wakeup-source;
-		};
-
-		menu {
-			label = "Menu";
-			gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_MENU>;
-		};
-
-		home {
-			label = "Home";
-			gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_HOME>;
-		};
-
-		back {
-			label = "Back";
-			gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_BACK>;
-		};
-
-		volume-up {
-			label = "Volume Up";
-			gpios = <&gpio7 13 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEUP>;
-		};
-
-		volume-down {
-			label = "Volume Down";
-			gpios = <&gpio4 5 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEDOWN>;
-		};
-	};
-
-	sound {
-		compatible = "fsl,imx6q-sabrelite-sgtl5000",
-			     "fsl,imx-audio-sgtl5000";
-		model = "imx6q-sabrelite-sgtl5000";
-		ssi-controller = <&ssi1>;
-		audio-codec = <&codec>;
-		audio-routing =
-			"MIC_IN", "Mic Jack",
-			"Mic Jack", "Mic Bias",
-			"Headphone Jack", "HP_OUT";
-		mux-int-port = <1>;
-		mux-ext-port = <4>;
-	};
-
-	backlight_lcd: backlight-lcd {
-		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <7>;
-		power-supply = <&reg_3p3v>;
-		status = "okay";
-	};
-
-	backlight_lvds: backlight-lvds {
-		compatible = "pwm-backlight";
-		pwms = <&pwm4 0 5000000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <7>;
-		power-supply = <&reg_3p3v>;
-		status = "okay";
-	};
-
-	lcd_display: disp0 {
-		compatible = "fsl,imx-parallel-display";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		interface-pix-fmt = "bgr666";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_j15>;
-		status = "okay";
-
-		port@0 {
-			reg = <0>;
-
-			lcd_display_in: endpoint {
-				remote-endpoint = <&ipu1_di0_disp0>;
-			};
-		};
-
-		port@1 {
-			reg = <1>;
-
-			lcd_display_out: endpoint {
-				remote-endpoint = <&lcd_panel_in>;
-			};
-		};
-	};
-
-	panel-lcd {
-		compatible = "okaya,rs800480t-7x0gp";
-		backlight = <&backlight_lcd>;
-
-		port {
-			lcd_panel_in: endpoint {
-				remote-endpoint = <&lcd_display_out>;
-			};
-		};
-	};
-
-	panel-lvds0 {
-		compatible = "hannstar,hsd100pxn1";
-		backlight = <&backlight_lvds>;
-
-		port {
-			panel_in: endpoint {
-				remote-endpoint = <&lvds0_out>;
-			};
-		};
-	};
-};
-
-&ipu1_csi0_from_ipu1_csi0_mux {
-	bus-width = <8>;
-	data-shift = <12>; /* Lines 19:12 used */
-	hsync-active = <1>;
-	vync-active = <1>;
-};
-
-&ipu1_csi0_mux_from_parallel_sensor {
-	remote-endpoint = <&ov5642_to_ipu1_csi0_mux>;
-};
-
-&ipu1_csi0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ipu1_csi0>;
-};
-
-&audmux {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_audmux>;
-	status = "okay";
-};
-
-&can1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_can1>;
-	xceiver-supply = <&reg_can_xcvr>;
-	status = "okay";
-};
-
-&clks {
-	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
-			  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
-	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
-				 <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
-};
-
-&ecspi1 {
-	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi1>;
-	status = "okay";
-
-	flash: m25p80@0 {
-		compatible = "sst,sst25vf016b", "jedec,spi-nor";
-		spi-max-frequency = <20000000>;
-		reg = <0>;
-	};
-};
-
-&fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
-	phy-handle = <&ethphy>;
-	phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
-	status = "okay";
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		ethphy: ethernet-phy {
-			compatible = "ethernet-phy-ieee802.3-c22";
-			txen-skew-ps = <0>;
-			txc-skew-ps = <3000>;
-			rxdv-skew-ps = <0>;
-			rxc-skew-ps = <3000>;
-			rxd0-skew-ps = <0>;
-			rxd1-skew-ps = <0>;
-			rxd2-skew-ps = <0>;
-			rxd3-skew-ps = <0>;
-			txd0-skew-ps = <0>;
-			txd1-skew-ps = <0>;
-			txd2-skew-ps = <0>;
-			txd3-skew-ps = <0>;
-		};
-	};
-};
-
-&hdmi {
-	ddc-i2c-bus = <&i2c2>;
-	status = "okay";
-};
-
-&i2c1 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c1>;
-	status = "okay";
-
-	codec: sgtl5000@a {
-		compatible = "fsl,sgtl5000";
-		reg = <0x0a>;
-		clocks = <&clks IMX6QDL_CLK_CKO>;
-		VDDA-supply = <&reg_2p5v>;
-		VDDIO-supply = <&reg_3p3v>;
-	};
-};
-
-&i2c2 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c2>;
-	status = "okay";
-
-	ov5640: camera@40 {
-		compatible = "ovti,ov5640";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_ov5640>;
-		reg = <0x40>;
-		clocks = <&mipi_xclk>;
-		clock-names = "xclk";
-		DOVDD-supply = <&reg_1p8v>;
-		AVDD-supply = <&reg_2p8v>;
-		DVDD-supply = <&reg_1p5v>;
-		reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; /* NANDF_D5 */
-		powerdown-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>; /* NANDF_WP_B */
-
-		port {
-			ov5640_to_mipi_csi2: endpoint {
-				remote-endpoint = <&mipi_csi2_in>;
-				clock-lanes = <0>;
-				data-lanes = <1 2>;
-			};
-		};
-	};
-
-	ov5642: camera@42 {
-		compatible = "ovti,ov5642";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_ov5642>;
-		clocks = <&clks IMX6QDL_CLK_CKO2>;
-		clock-names = "xclk";
-		reg = <0x42>;
-		reset-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
-		powerdown-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
-		gp-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
-		status = "disabled";
-
-		port {
-			ov5642_to_ipu1_csi0_mux: endpoint {
-				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
-				bus-width = <8>;
-				hsync-active = <1>;
-				vsync-active = <1>;
-			};
-		};
-	};
-};
-
-&i2c3 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c3>;
-	status = "okay";
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_hog>;
-
-	imx6q-sabrelite {
-		pinctrl_hog: hoggrp {
-			fsl,pins = <
-				/* SGTL5000 sys_mclk */
-				MX6QDL_PAD_GPIO_0__CCM_CLKO1    0x030b0
-			>;
-		};
-
-		pinctrl_audmux: audmuxgrp {
-			fsl,pins = <
-				MX6QDL_PAD_SD2_DAT0__AUD4_RXD		0x130b0
-				MX6QDL_PAD_SD2_DAT3__AUD4_TXC		0x130b0
-				MX6QDL_PAD_SD2_DAT2__AUD4_TXD		0x110b0
-				MX6QDL_PAD_SD2_DAT1__AUD4_TXFS		0x130b0
-			>;
-		};
-
-		pinctrl_can1: can1grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b0
-				MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX	0x1b0b0
-			>;
-		};
-
-		pinctrl_can_xcvr: can-xcvrgrp {
-			fsl,pins = <
-				/* Flexcan XCVR enable */
-				MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1b0b0
-			>;
-		};
-
-		pinctrl_ecspi1: ecspi1grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
-				MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
-				MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
-				MX6QDL_PAD_EIM_D19__GPIO3_IO19  0x000b1	/* CS */
-			>;
-		};
-
-		pinctrl_enet: enetgrp {
-			fsl,pins = <
-				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x100b0
-				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x100b0
-				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x10030
-				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x10030
-				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x10030
-				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x10030
-				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x10030
-				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x10030
-				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x100b0
-				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
-				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
-				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
-				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
-				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
-				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
-				/* Phy reset */
-				MX6QDL_PAD_EIM_D23__GPIO3_IO23		0x000b0
-			>;
-		};
-
-		pinctrl_gpio_keys: gpio-keysgrp {
-			fsl,pins = <
-				/* Power Button */
-				MX6QDL_PAD_NANDF_D3__GPIO2_IO03		0x1b0b0
-				/* Menu Button */
-				MX6QDL_PAD_NANDF_D1__GPIO2_IO01		0x1b0b0
-				/* Home Button */
-				MX6QDL_PAD_NANDF_D4__GPIO2_IO04		0x1b0b0
-				/* Back Button */
-				MX6QDL_PAD_NANDF_D2__GPIO2_IO02		0x1b0b0
-				/* Volume Up Button */
-				MX6QDL_PAD_GPIO_18__GPIO7_IO13		0x1b0b0
-				/* Volume Down Button */
-				MX6QDL_PAD_GPIO_19__GPIO4_IO05		0x1b0b0
-			>;
-		};
-
-		pinctrl_i2c1: i2c1grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
-				MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
-			>;
-		};
-
-		pinctrl_i2c2: i2c2grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
-				MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
-			>;
-		};
-
-		pinctrl_i2c3: i2c3grp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_5__I2C3_SCL		0x4001b8b1
-				MX6QDL_PAD_GPIO_16__I2C3_SDA		0x4001b8b1
-			>;
-		};
-
-		pinctrl_ipu1_csi0: ipu1csi0grp {
-			fsl,pins = <
-				MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12    0x1b0b0
-				MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13    0x1b0b0
-				MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14    0x1b0b0
-				MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15    0x1b0b0
-				MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16    0x1b0b0
-				MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17    0x1b0b0
-				MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18    0x1b0b0
-				MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19    0x1b0b0
-				MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK   0x1b0b0
-				MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC      0x1b0b0
-				MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC     0x1b0b0
-				MX6QDL_PAD_CSI0_DATA_EN__IPU1_CSI0_DATA_EN 0x1b0b0
-			>;
-		};
-
-		pinctrl_j15: j15grp {
-			fsl,pins = <
-				MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
-				MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15       0x10
-				MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02        0x10
-				MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03        0x10
-				MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00   0x10
-				MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01   0x10
-				MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02   0x10
-				MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03   0x10
-				MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04   0x10
-				MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05   0x10
-				MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06   0x10
-				MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07   0x10
-				MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08   0x10
-				MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09   0x10
-				MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10  0x10
-				MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11  0x10
-				MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12  0x10
-				MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13  0x10
-				MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14  0x10
-				MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15  0x10
-				MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16  0x10
-				MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17  0x10
-				MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18  0x10
-				MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19  0x10
-				MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20  0x10
-				MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21  0x10
-				MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22  0x10
-				MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23  0x10
-			>;
-		};
-
-		pinctrl_ov5640: ov5640grp {
-			fsl,pins = <
-				MX6QDL_PAD_NANDF_D5__GPIO2_IO05   0x000b0
-				MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09 0x0b0b0
-			>;
-		};
-
-		pinctrl_ov5642: ov5642grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_DAT0__GPIO1_IO16 0x1b0b0
-				MX6QDL_PAD_GPIO_6__GPIO1_IO06   0x1b0b0
-				MX6QDL_PAD_GPIO_8__GPIO1_IO08   0x130b0
-				MX6QDL_PAD_GPIO_3__CCM_CLKO2    0x000b0
-			>;
-		};
-
-		pinctrl_pwm1: pwm1grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1
-			>;
-		};
-
-		pinctrl_pwm3: pwm3grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_DAT1__PWM3_OUT 0x1b0b1
-			>;
-		};
-
-		pinctrl_pwm4: pwm4grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1
-			>;
-		};
-
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
-				MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA	0x1b0b1
-			>;
-		};
-
-		pinctrl_uart2: uart2grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D26__UART2_TX_DATA	0x1b0b1
-				MX6QDL_PAD_EIM_D27__UART2_RX_DATA	0x1b0b1
-			>;
-		};
-
-		pinctrl_usbh1: usbh1grp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_17__GPIO7_IO12		0x030b0
-			>;
-		};
-
-		pinctrl_usbotg: usbotggrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
-				MX6QDL_PAD_KEY_COL4__USB_OTG_OC	0x1b0b0
-				/* power enable, high active */
-				MX6QDL_PAD_EIM_D22__GPIO3_IO22  0x000b0
-			>;
-		};
-
-		pinctrl_usdhc3: usdhc3grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
-				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
-				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
-				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
-				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
-				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
-				MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0	/* CD */
-				MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x1f0b0	/* WP */
-			>;
-		};
-
-		pinctrl_usdhc4: usdhc4grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
-				MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
-				MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
-				MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
-				MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
-				MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059
-				MX6QDL_PAD_NANDF_D6__GPIO2_IO06 0x1b0b0	/* CD */
-			>;
-		};
-	};
-};
-
-&ipu1_di0_disp0 {
-	remote-endpoint = <&lcd_display_in>;
-};
-
-&ldb {
-	status = "okay";
-
-	lvds-channel@0 {
-		status = "okay";
-
-		port@4 {
-			reg = <4>;
-
-			lvds0_out: endpoint {
-				remote-endpoint = <&panel_in>;
-			};
-		};
-	};
-};
-
-&pcie {
-	status = "okay";
-};
-
-&pwm1 {
-	#pwm-cells = <2>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm1>;
-	status = "okay";
-};
-
-&pwm3 {
-	#pwm-cells = <2>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm3>;
-	status = "okay";
-};
-
-&pwm4 {
-	#pwm-cells = <2>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm4>;
-	status = "okay";
-};
-
-&ssi1 {
-	status = "okay";
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
-	status = "okay";
-};
-
-&uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
-	status = "okay";
-};
-
-&usbh1 {
-	vbus-supply = <&reg_usb_h1_vbus>;
-	status = "okay";
-};
-
-&usbotg {
-	vbus-supply = <&reg_usb_otg_vbus>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbotg>;
-	disable-over-current;
-	status = "okay";
-};
-
-&usdhc3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc3>;
-	cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
-	vmmc-supply = <&reg_3p3v>;
-	status = "okay";
-};
-
-&usdhc4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc4>;
-	cd-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
-	vmmc-supply = <&reg_3p3v>;
-	status = "okay";
-};
-
-&mipi_csi {
-	status = "okay";
-
-	port@0 {
-		reg = <0>;
-
-		mipi_csi2_in: endpoint {
-			remote-endpoint = <&ov5640_to_mipi_csi2>;
-			clock-lanes = <0>;
-			data-lanes = <1 2>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx6qdl-tx6-mb7.dtsi b/arch/arm/boot/dts/imx6qdl-tx6-mb7.dtsi
deleted file mode 100644
index 99ec7a838f8d..000000000000
--- a/arch/arm/boot/dts/imx6qdl-tx6-mb7.dtsi
+++ /dev/null
@@ -1,96 +0,0 @@
-/*
- * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/ {
-	backlight0 {
-		pwms = <&pwm1 0 500000 PWM_POLARITY_INVERTED>;
-		turn-on-delay-ms = <35>;
-		power-supply = <&reg_lcd1_pwr>;
-	};
-
-	backlight1 {
-		pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
-		turn-on-delay-ms = <35>;
-		power-supply = <&reg_lcd1_pwr>;
-	};
-
-	lcd-panel {
-		compatible = "edt,et057090dhu";
-		pixelclk-active = <0>;
-	};
-
-	lvds0-panel {
-		compatible = "edt,etml1010g0dka";
-		pixelclk-active = <0>;
-	};
-
-	lvds1-panel {
-		compatible = "edt,etml1010g0dka";
-		pixelclk-active = <0>;
-	};
-};
-
-&can1 {
-	status = "disabled";
-};
-
-&can2 {
-	xceiver-supply = <&reg_3v3>;
-};
-
-&ds1339 {
-	/*
-	 * The backup voltage of the module internal RTC is not wired
-	 * by default on the MB7, so disable that RTC chip.
-	 */
-	status = "disabled";
-};
-
-&i2c3 {
-	rtc: rtc@6f {
-		compatible = "microchip,mcp7940x";
-		reg = <0x6f>;
-	};
-};
-
-&reg_lcd0_pwr {
-	status = "disabled";
-};
diff --git a/arch/arm/boot/dts/imx6qdl-udoo.dtsi b/arch/arm/boot/dts/imx6qdl-udoo.dtsi
deleted file mode 100644
index ccfa8e320be6..000000000000
--- a/arch/arm/boot/dts/imx6qdl-udoo.dtsi
+++ /dev/null
@@ -1,327 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright 2013 Freescale Semiconductor, Inc.
- *
- * Author: Fabio Estevam <fabio.estevam@freescale.com>
- */
-
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
-	aliases {
-		backlight = &backlight;
-		panelchan = &panelchan;
-		panel7 = &panel7;
-		touchscreenp7 = &touchscreenp7;
-	};
-
-	chosen {
-		stdout-path = &uart2;
-	};
-
-	backlight: backlight {
-		compatible = "gpio-backlight";
-		gpios = <&gpio1 4 0>;
-		default-on;
-		status = "disabled";
-	};
-
-	gpio-poweroff {
-		compatible = "gpio-poweroff";
-		gpios = <&gpio2 4 0>;
-		pinctrl-0 = <&pinctrl_power_off>;
-		pinctrl-names = "default";
-	};
-
-	memory@10000000 {
-		device_type = "memory";
-		reg = <0x10000000 0x40000000>;
-	};
-
-	panel7: panel7 {
-		/*
-		 * in reality it is a -20t (parallel) model,
-		 * but with LVDS bridge chip attached,
-		 * so it is equivalent to -19t model in drive
-		 * characteristics
-		 */
-		compatible = "urt,umsh-8596md-19t";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_panel>;
-		power-supply = <&reg_panel>;
-		backlight = <&backlight>;
-		status = "disabled";
-
-		port {
-			panel_in: endpoint {
-				remote-endpoint = <&lvds0_out>;
-			};
-		};
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_usb_h1_vbus: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "usb_h1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			startup-delay-us = <2>; /* USB2415 requires a POR of 1 us minimum */
-			gpio = <&gpio7 12 0>;
-		};
-
-		reg_panel: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "lcd_panel";
-			enable-active-high;
-			gpio = <&gpio1 2 0>;
-		};
-	};
-
-	sound {
-		compatible = "fsl,imx6q-udoo-ac97",
-			     "fsl,imx-audio-ac97";
-		model = "fsl,imx6q-udoo-ac97";
-		audio-cpu = <&ssi1>;
-		audio-routing =
-			"RX", "Mic Jack",
-			"Headphone Jack", "TX";
-		mux-int-port = <1>;
-		mux-ext-port = <6>;
-	};
-};
-
-&fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii-id";
-	status = "okay";
-};
-
-&hdmi {
-	ddc-i2c-bus = <&i2c2>;
-	status = "okay";
-};
-
-&i2c2 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c2>;
-	status = "okay";
-};
-
-&i2c3 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c3>;
-	status = "okay";
-
-	touchscreenp7: touchscreenp7@55 {
-		compatible = "sitronix,st1232";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_touchscreenp7>;
-		reg = <0x55>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <13 8>;
-		gpios = <&gpio1 15 0>;
-		status = "disabled";
-	};
-};
-
-&iomuxc {
-	imx6q-udoo {
-		pinctrl_enet: enetgrp {
-			fsl,pins = <
-				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
-				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
-				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
-				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
-				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
-				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
-				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
-				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
-				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
-				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
-				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
-				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
-				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
-				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
-				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
-				MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
-			>;
-		};
-
-		pinctrl_i2c2: i2c2grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
-				MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
-			>;
-		};
-
-		pinctrl_i2c3: i2c3grp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_5__I2C3_SCL		0x4001f8b1
-				MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001f8b1
-			>;
-		};
-
-		pinctrl_panel: panelgrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x70
-				MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x70
-			>;
-		};
-
-		pinctrl_power_off: poweroffgrp {
-			fsl,pins = <
-				MX6QDL_PAD_NANDF_D4__GPIO2_IO04		0x30
-			>;
-		};
-
-		pinctrl_touchscreenp7: touchscreenp7grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD2_DAT0__GPIO1_IO15		0x70
-				MX6QDL_PAD_SD2_DAT2__GPIO1_IO13		0x1b0b0
-			>;
-		};
-
-		pinctrl_uart2: uart2grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D26__UART2_TX_DATA	0x1b0b1
-				MX6QDL_PAD_EIM_D27__UART2_RX_DATA	0x1b0b1
-			>;
-		};
-
-		pinctrl_uart4: uart4grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL0__UART4_TX_DATA	0x1b0b1
-				MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA	0x1b0b1
-			>;
-		};
-
-		pinctrl_usbh: usbhgrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x80000000
-				MX6QDL_PAD_NANDF_CS2__CCM_CLKO2 0x130b0
-			>;
-		};
-
-		pinctrl_usbotg: usbotg {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
-				MX6QDL_PAD_EIM_D22__USB_OTG_PWR 0x17059
-				MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x17059
-			>;
-		};
-
-		pinctrl_usdhc3: usdhc3grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
-				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
-				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
-				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
-				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
-				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
-				MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x1b0b0
-			>;
-		};
-
-		pinctrl_ac97_running: ac97running {
-			fsl,pins = <
-				MX6QDL_PAD_DI0_PIN2__AUD6_TXD		0x1b0b0
-				MX6QDL_PAD_DI0_PIN3__AUD6_TXFS		0x1b0b0
-				MX6QDL_PAD_DI0_PIN4__AUD6_RXD		0x13080
-				MX6QDL_PAD_DI0_PIN15__AUD6_TXC		0x13080
-				MX6QDL_PAD_EIM_EB2__GPIO2_IO30		0x1b0b0
-			>;
-		};
-
-		pinctrl_ac97_warm_reset: ac97warmreset {
-			fsl,pins = <
-				MX6QDL_PAD_DI0_PIN2__AUD6_TXD		0x1b0b0
-				MX6QDL_PAD_DI0_PIN3__GPIO4_IO19		0x1b0b0
-				MX6QDL_PAD_DI0_PIN4__AUD6_RXD		0x13080
-				MX6QDL_PAD_DI0_PIN15__AUD6_TXC		0x13080
-				MX6QDL_PAD_EIM_EB2__GPIO2_IO30		0x1b0b0
-			>;
-		};
-
-		pinctrl_ac97_reset: ac97reset {
-			fsl,pins = <
-				MX6QDL_PAD_DI0_PIN2__GPIO4_IO18		0x1b0b0
-				MX6QDL_PAD_DI0_PIN3__GPIO4_IO19		0x1b0b0
-				MX6QDL_PAD_DI0_PIN4__AUD6_RXD		0x13080
-				MX6QDL_PAD_DI0_PIN15__AUD6_TXC		0x13080
-				MX6QDL_PAD_EIM_EB2__GPIO2_IO30		0x1b0b0
-			>;
-		};
-	};
-};
-
-&ldb {
-	status = "okay";
-
-	panelchan: lvds-channel@0 {
-		port@4 {
-			reg = <4>;
-
-			lvds0_out: endpoint {
-				remote-endpoint = <&panel_in>;
-			};
-		};
-	};
-};
-
-&uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
-	status = "okay";
-};
-
-&uart4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart4>;
-	status = "okay";
-};
-
-&usbh1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbh>;
-	vbus-supply = <&reg_usb_h1_vbus>;
-	clocks = <&clks IMX6QDL_CLK_CKO>;
-	status = "okay";
-};
-
-&usbotg {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbotg>;
-	status = "okay";
-};
-
-&usdhc3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc3>;
-	cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-&audmux {
-	status = "okay";
-};
-
-&ssi1 {
-	cell-index = <0>;
-	fsl,mode = "ac97-slave";
-	pinctrl-names = "ac97-running", "ac97-reset", "ac97-warm-reset";
-	pinctrl-0 = <&pinctrl_ac97_running>;
-	pinctrl-1 = <&pinctrl_ac97_reset>;
-	pinctrl-2 = <&pinctrl_ac97_warm_reset>;
-	ac97-gpios = <&gpio4 19 0 &gpio4 18 0 &gpio2 30 0>;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6qdl-wandboard-revb1.dtsi b/arch/arm/boot/dts/imx6qdl-wandboard-revb1.dtsi
deleted file mode 100644
index e781a45785ed..000000000000
--- a/arch/arm/boot/dts/imx6qdl-wandboard-revb1.dtsi
+++ /dev/null
@@ -1,36 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-//
-// Copyright 2013 Freescale Semiconductor, Inc.
-//
-// Author: Fabio Estevam <fabio.estevam@freescale.com>
-
-#include "imx6qdl-wandboard.dtsi"
-
-&iomuxc {
-	pinctrl-0 = <&pinctrl_hog>;
-
-	imx6qdl-wandboard {
-		pinctrl_hog: hoggrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x80000000	/* uSDHC1 CD */
-				MX6QDL_PAD_EIM_DA9__GPIO3_IO09		0x80000000	/* uSDHC3 CD */
-				MX6QDL_PAD_EIM_EB1__GPIO2_IO29		0x0f0b0		/* WL_REF_ON */
-				MX6QDL_PAD_EIM_A25__GPIO5_IO02		0x0f0b0		/* WL_RST_N */
-				MX6QDL_PAD_ENET_RXD1__GPIO1_IO26	0x000b0		/* WL_REG_ON */
-				MX6QDL_PAD_ENET_TXD1__GPIO1_IO29	0x80000000	/* WL_HOST_WAKE */
-				MX6QDL_PAD_ENET_TXD0__GPIO1_IO30	0x80000000	/* WL_WAKE */
-				MX6QDL_PAD_EIM_D29__GPIO3_IO29		0x80000000	/* RGMII_nRST */
-				MX6QDL_PAD_EIM_DA13__GPIO3_IO13		0x80000000	/* BT_ON */
-				MX6QDL_PAD_EIM_DA14__GPIO3_IO14		0x80000000	/* BT_WAKE */
-				MX6QDL_PAD_EIM_DA15__GPIO3_IO15		0x80000000	/* BT_HOST_WAKE */
-			>;
-		};
-	};
-};
-
-&usdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc2>;
-	non-removable;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6qdl-wandboard-revc1.dtsi b/arch/arm/boot/dts/imx6qdl-wandboard-revc1.dtsi
deleted file mode 100644
index 3874e74703f0..000000000000
--- a/arch/arm/boot/dts/imx6qdl-wandboard-revc1.dtsi
+++ /dev/null
@@ -1,35 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-//
-// Copyright 2013 Freescale Semiconductor, Inc.
-//
-// Author: Fabio Estevam <fabio.estevam@freescale.com>
-
-#include "imx6qdl-wandboard.dtsi"
-
-&iomuxc {
-	pinctrl-0 = <&pinctrl_hog>;
-
-	imx6qdl-wandboard {
-		pinctrl_hog: hoggrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x80000000	/* uSDHC1 CD */
-				MX6QDL_PAD_EIM_DA9__GPIO3_IO09		0x80000000	/* uSDHC3 CD */
-				MX6QDL_PAD_CSI0_DAT14__GPIO6_IO00	0x0f0b0		/* WIFI_ON (reset, active low) */
-				MX6QDL_PAD_ENET_RXD1__GPIO1_IO26	0x000b0		/* WL_REG_ON (unused) */
-				MX6QDL_PAD_ENET_TXD1__GPIO1_IO29	0x80000000	/* WL_HOST_WAKE, input */
-				MX6QDL_PAD_CSI0_DAT13__GPIO5_IO31	0x0f0b0		/* GPIO5_IO31 (Wifi Power Enable) */
-				MX6QDL_PAD_ENET_TXD0__GPIO1_IO30	0x80000000	/* WL_WAKE (unused) */
-				MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21	0x80000000	/* BT_ON */
-				MX6QDL_PAD_CSI0_DAT12__GPIO5_IO30	0x80000000	/* BT_WAKE */
-				MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20	0x80000000	/* BT_HOST_WAKE */
-				MX6QDL_PAD_EIM_D29__GPIO3_IO29		0x80000000	/* RGMII_nRST */
-			>;
-		};
-	};
-};
-
-&usdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc2>;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6qp-sabreauto.dts b/arch/arm/boot/dts/imx6qp-sabreauto.dts
deleted file mode 100644
index 2bb3bfb18ec3..000000000000
--- a/arch/arm/boot/dts/imx6qp-sabreauto.dts
+++ /dev/null
@@ -1,60 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
-//
-// Copyright 2016 Freescale Semiconductor, Inc.
-
-/dts-v1/;
-
-#include "imx6qp.dtsi"
-#include "imx6qdl-sabreauto.dtsi"
-
-/ {
-	model = "Freescale i.MX6 Quad Plus SABRE Automotive Board";
-	compatible = "fsl,imx6qp-sabreauto", "fsl,imx6qp";
-};
-
-&i2c2 {
-	max7322: gpio@68 {
-		compatible = "maxim,max7322";
-		reg = <0x68>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-};
-
-&iomuxc {
-	imx6qdl-sabreauto {
-		pinctrl_enet: enetgrp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL1__ENET_MDIO          0x1b0b0
-				MX6QDL_PAD_KEY_COL2__ENET_MDC           0x1b0b0
-				MX6QDL_PAD_RGMII_TXC__RGMII_TXC         0x1b018
-				MX6QDL_PAD_RGMII_TD0__RGMII_TD0         0x1b018
-				MX6QDL_PAD_RGMII_TD1__RGMII_TD1         0x1b018
-				MX6QDL_PAD_RGMII_TD2__RGMII_TD2         0x1b018
-				MX6QDL_PAD_RGMII_TD3__RGMII_TD3         0x1b018
-				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL   0x1b018
-				MX6QDL_PAD_RGMII_RXC__RGMII_RXC         0x1b018
-				MX6QDL_PAD_RGMII_RD0__RGMII_RD0         0x1b018
-				MX6QDL_PAD_RGMII_RD1__RGMII_RD1         0x1b018
-				MX6QDL_PAD_RGMII_RD2__RGMII_RD2         0x1b018
-				MX6QDL_PAD_RGMII_RD3__RGMII_RD3         0x1b018
-				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL   0x1b018
-				MX6QDL_PAD_GPIO_16__ENET_REF_CLK        0x4001b0a8
-				MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
-			>;
-		};
-	};
-};
-
-&pcie {
-	reset-gpio = <&max7310_c 5 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-&sata {
-	status = "okay";
-};
-
-&vgen3_reg {
-	regulator-always-on;
-};
diff --git a/arch/arm/boot/dts/imx6qp-sabresd.dts b/arch/arm/boot/dts/imx6qp-sabresd.dts
deleted file mode 100644
index f69eec18d865..000000000000
--- a/arch/arm/boot/dts/imx6qp-sabresd.dts
+++ /dev/null
@@ -1,63 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
-//
-// Copyright 2016 Freescale Semiconductor, Inc.
-
-/dts-v1/;
-
-#include "imx6qp.dtsi"
-#include "imx6qdl-sabresd.dtsi"
-
-/ {
-	model = "Freescale i.MX6 Quad Plus SABRE Smart Device Board";
-	compatible = "fsl,imx6qp-sabresd", "fsl,imx6qp";
-};
-
-&reg_arm {
-	vin-supply = <&sw2_reg>;
-};
-
-&iomuxc {
-	imx6qdl-sabresd {
-		pinctrl_usdhc2: usdhc2grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
-				MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10071
-				MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
-				MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
-				MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
-				MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
-				MX6QDL_PAD_NANDF_D4__SD2_DATA4		0x17059
-				MX6QDL_PAD_NANDF_D5__SD2_DATA5		0x17059
-				MX6QDL_PAD_NANDF_D6__SD2_DATA6		0x17059
-				MX6QDL_PAD_NANDF_D7__SD2_DATA7		0x17059
-			>;
-		};
-
-		pinctrl_usdhc3: usdhc3grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
-				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10071
-				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
-				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
-				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
-				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
-				MX6QDL_PAD_SD3_DAT4__SD3_DATA4		0x17059
-				MX6QDL_PAD_SD3_DAT5__SD3_DATA5		0x17059
-				MX6QDL_PAD_SD3_DAT6__SD3_DATA6		0x17059
-				MX6QDL_PAD_SD3_DAT7__SD3_DATA7		0x17059
-			>;
-		};
-	};
-};
-
-&vgen3_reg {
-	regulator-always-on;
-};
-
-&pcie {
-	status = "okay";
-};
-
-&sata {
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6qp-tx6qp-8037-mb7.dts b/arch/arm/boot/dts/imx6qp-tx6qp-8037-mb7.dts
deleted file mode 100644
index 92b38e6699aa..000000000000
--- a/arch/arm/boot/dts/imx6qp-tx6qp-8037-mb7.dts
+++ /dev/null
@@ -1,48 +0,0 @@
-/*
- * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6qp-tx6qp-8037.dts"
-#include "imx6qdl-tx6-mb7.dtsi"
-
-/ {
-	model = "Ka-Ro electronics TX6Q-8037 Module on MB7 baseboard";
-};
diff --git a/arch/arm/boot/dts/imx6qp-tx6qp-8037.dts b/arch/arm/boot/dts/imx6qp-tx6qp-8037.dts
deleted file mode 100644
index ffc0f2ee11d2..000000000000
--- a/arch/arm/boot/dts/imx6qp-tx6qp-8037.dts
+++ /dev/null
@@ -1,86 +0,0 @@
-/*
- * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6qp.dtsi"
-#include "imx6qdl-tx6.dtsi"
-#include "imx6qdl-tx6-lcd.dtsi"
-
-/ {
-	model = "Ka-Ro electronics TX6QP-8037 Module";
-	compatible = "karo,imx6qp-tx6qp", "fsl,imx6qp";
-};
-
-&ds1339 {
-	status = "disabled";
-};
-
-&gpmi {
-	status = "disabled";
-};
-
-&ipu2 {
-	status = "disabled";
-};
-
-&usdhc4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc4>;
-	bus-width = <4>;
-	non-removable;
-	no-1-8-v;
-	fsl,wp-controller;
-	status = "okay";
-};
-
-&iomuxc {
-	pinctrl_usdhc4: usdhc4grp {
-		fsl,pins = <
-			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x070b1
-			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x070b1
-			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x070b1
-			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x070b1
-			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x070b1
-			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x070b1
-			MX6QDL_PAD_NANDF_ALE__SD4_RESET		0x0b0b1
-		>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx6qp-tx6qp-8137-mb7.dts b/arch/arm/boot/dts/imx6qp-tx6qp-8137-mb7.dts
deleted file mode 100644
index 07ad70718aec..000000000000
--- a/arch/arm/boot/dts/imx6qp-tx6qp-8137-mb7.dts
+++ /dev/null
@@ -1,57 +0,0 @@
-/*
- * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6qp-tx6qp-8137.dts"
-#include "imx6qdl-tx6-mb7.dtsi"
-
-/ {
-	model = "Ka-Ro electronics TX6Q-8137 Module on MB7 baseboard";
-	compatible = "karo,imx6qp-tx6qp", "fsl,imx6qp";
-};
-
-&ipu2 {
-	status = "disabled";
-};
-
-&sata {
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6qp-tx6qp-8137.dts b/arch/arm/boot/dts/imx6qp-tx6qp-8137.dts
deleted file mode 100644
index dd494d587014..000000000000
--- a/arch/arm/boot/dts/imx6qp-tx6qp-8137.dts
+++ /dev/null
@@ -1,90 +0,0 @@
-/*
- * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6qp.dtsi"
-#include "imx6qdl-tx6.dtsi"
-#include "imx6qdl-tx6-lvds.dtsi"
-
-/ {
-	model = "Ka-Ro electronics TX6QP-8137 Module";
-	compatible = "karo,imx6qp-tx6qp", "fsl,imx6qp";
-};
-
-&ds1339 {
-	status = "disabled";
-};
-
-&gpmi {
-	status = "disabled";
-};
-
-&ipu2 {
-	status = "disabled";
-};
-
-&sata {
-	status = "okay";
-};
-
-&usdhc4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc4>;
-	bus-width = <4>;
-	non-removable;
-	no-1-8-v;
-	fsl,wp-controller;
-	status = "okay";
-};
-
-&iomuxc {
-	pinctrl_usdhc4: usdhc4grp {
-		fsl,pins = <
-			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x070b1
-			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x070b1
-			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x070b1
-			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x070b1
-			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x070b1
-			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x070b1
-			MX6QDL_PAD_NANDF_ALE__SD4_RESET		0x0b0b1
-		>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx6sx-sdb.dtsi b/arch/arm/boot/dts/imx6sx-sdb.dtsi
deleted file mode 100644
index c6e85e4a0883..000000000000
--- a/arch/arm/boot/dts/imx6sx-sdb.dtsi
+++ /dev/null
@@ -1,718 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-//
-// Copyright (C) 2014 Freescale Semiconductor, Inc.
-
-/dts-v1/;
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include "imx6sx.dtsi"
-
-/ {
-	model = "Freescale i.MX6 SoloX SDB Board";
-	compatible = "fsl,imx6sx-sdb", "fsl,imx6sx";
-
-	chosen {
-		stdout-path = &uart1;
-	};
-
-	memory@80000000 {
-		device_type = "memory";
-		reg = <0x80000000 0x40000000>;
-	};
-
-	backlight_display: backlight-display {
-		compatible = "pwm-backlight";
-		pwms = <&pwm3 0 5000000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <6>;
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpio_keys>;
-
-		volume-up {
-			label = "Volume Up";
-			gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEUP>;
-			wakeup-source;
-		};
-
-		volume-down {
-			label = "Volume Down";
-			gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEDOWN>;
-			wakeup-source;
-		};
-	};
-
-	vcc_sd3: regulator-vcc-sd3 {
-		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_vcc_sd3>;
-		regulator-name = "VCC_SD3";
-		regulator-min-microvolt = <3000000>;
-		regulator-max-microvolt = <3000000>;
-		gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
-		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_usb_otg1>;
-		regulator-name = "usb_otg1_vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	reg_usb_otg2_vbus: regulator-usb-otg2-vbus {
-		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_usb_otg2>;
-		regulator-name = "usb_otg2_vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	reg_psu_5v: regulator-psu-5v {
-		compatible = "regulator-fixed";
-		regulator-name = "PSU-5V0";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-	};
-
-	reg_lcd_3v3: regulator-lcd-3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "lcd-3v3";
-		gpio = <&gpio3 27 0>;
-		enable-active-high;
-	};
-
-	reg_peri_3v3: regulator-peri-3v3 {
-		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_peri_3v3>;
-		regulator-name = "peri_3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		gpio = <&gpio4 16 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-		regulator-always-on;
-	};
-
-	reg_enet_3v3: regulator-enet-3v3 {
-		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_enet_3v3>;
-		regulator-name = "enet_3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		gpio = <&gpio2 6 GPIO_ACTIVE_LOW>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	reg_pcie_gpio: regulator-pcie-gpio {
-		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_pcie_reg>;
-		regulator-name = "MPCIE_3V3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		gpio = <&gpio2 1 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	reg_lcd_5v: regulator-lcd-5v {
-		compatible = "regulator-fixed";
-		regulator-name = "lcd-5v0";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-	};
-
-	reg_can_en: regulator-can-en {
-		compatible = "regulator-fixed";
-		regulator-name = "can-en";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	reg_can_stby: regulator-can-stby {
-		compatible = "regulator-fixed";
-		regulator-name = "can-stby";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	sound {
-		compatible = "fsl,imx6sx-sdb-wm8962", "fsl,imx-audio-wm8962";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_hp>;
-		model = "wm8962-audio";
-		ssi-controller = <&ssi2>;
-		audio-codec = <&codec>;
-		audio-routing =
-			"Headphone Jack", "HPOUTL",
-			"Headphone Jack", "HPOUTR",
-			"Ext Spk", "SPKOUTL",
-			"Ext Spk", "SPKOUTR",
-			"AMIC", "MICBIAS",
-			"IN3R", "AMIC";
-		mux-int-port = <2>;
-		mux-ext-port = <6>;
-		hp-det-gpio = <&gpio1 17 GPIO_ACTIVE_LOW>;
-	};
-
-	panel {
-		compatible = "sii,43wvf1g";
-		backlight = <&backlight_display>;
-		dvdd-supply = <&reg_lcd_3v3>;
-		avdd-supply = <&reg_lcd_5v>;
-
-		port {
-			panel_in: endpoint {
-				remote-endpoint = <&display_out>;
-			};
-		};
-	};
-
-	sound-spdif {
-		compatible = "fsl,imx-audio-spdif",
-			   "fsl,imx6sx-sdb-spdif";
-		model = "imx-spdif";
-		spdif-controller = <&spdif>;
-		spdif-out;
-	};
-
-};
-
-&audmux {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_audmux>;
-	status = "okay";
-};
-
-&fec1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet1>;
-	phy-supply = <&reg_enet_3v3>;
-	phy-mode = "rgmii-id";
-	phy-handle = <&ethphy1>;
-	phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
-	fsl,magic-packet;
-	status = "okay";
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		ethphy1: ethernet-phy@1 {
-			reg = <1>;
-		};
-
-		ethphy2: ethernet-phy@2 {
-			reg = <2>;
-		};
-	};
-};
-
-&fec2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet2>;
-	phy-mode = "rgmii-id";
-	phy-handle = <&ethphy2>;
-	fsl,magic-packet;
-	status = "okay";
-};
-
-&flexcan1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_flexcan1>;
-	xceiver-supply = <&reg_can_stby>;
-	status = "okay";
-};
-
-&flexcan2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_flexcan2>;
-	xceiver-supply = <&reg_can_stby>;
-	status = "okay";
-};
-
-&i2c3 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c3>;
-	status = "okay";
-};
-
-&i2c4 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c4>;
-	status = "okay";
-
-	codec: wm8962@1a {
-		compatible = "wlf,wm8962";
-		reg = <0x1a>;
-		clocks = <&clks IMX6SX_CLK_AUDIO>;
-		DCVDD-supply = <&vgen4_reg>;
-		DBVDD-supply = <&vgen4_reg>;
-		AVDD-supply = <&vgen4_reg>;
-		CPVDD-supply = <&vgen4_reg>;
-		MICVDD-supply = <&vgen3_reg>;
-		PLLVDD-supply = <&vgen4_reg>;
-		SPKVDD1-supply = <&reg_psu_5v>;
-		SPKVDD2-supply = <&reg_psu_5v>;
-	};
-};
-
-&pcie {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pcie>;
-	reset-gpio = <&gpio2 0 GPIO_ACTIVE_LOW>;
-	vpcie-supply = <&reg_pcie_gpio>;
-	status = "okay";
-};
-
-&lcdif1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_lcd>;
-	status = "okay";
-
-	port {
-		display_out: endpoint {
-			remote-endpoint = <&panel_in>;
-		};
-	};
-};
-
-&pwm3 {
-	#pwm-cells = <2>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm3>;
-	status = "okay";
-};
-
-&snvs_poweroff {
-	status = "okay";
-};
-
-&sai1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_sai1>;
-	status = "disabled";
-};
-
-&spdif {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_spdif>;
-	assigned-clocks = <&clks IMX6SX_CLK_SPDIF_PODF>;
-	assigned-clock-rates = <24576000>;
-	status = "okay";
-};
-
-&ssi2 {
-	status = "okay";
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
-	status = "okay";
-};
-
-&uart5 { /* for bluetooth */
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart5>;
-	uart-has-rtscts;
-	status = "okay";
-};
-
-&usbotg1 {
-	vbus-supply = <&reg_usb_otg1_vbus>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usb_otg1_id>;
-	status = "okay";
-};
-
-&usbotg2 {
-	vbus-supply = <&reg_usb_otg2_vbus>;
-	dr_mode = "host";
-	status = "okay";
-};
-
-&usbphy1 {
-	fsl,tx-d-cal = <106>;
-};
-
-&usbphy2 {
-	fsl,tx-d-cal = <106>;
-};
-
-&usdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc2>;
-	non-removable;
-	no-1-8-v;
-	keep-power-in-suspend;
-	wakeup-source;
-	status = "okay";
-};
-
-&usdhc3 {
-	pinctrl-names = "default", "state_100mhz", "state_200mhz";
-	pinctrl-0 = <&pinctrl_usdhc3>;
-	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
-	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
-	bus-width = <8>;
-	cd-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio2 15 GPIO_ACTIVE_HIGH>;
-	keep-power-in-suspend;
-	wakeup-source;
-	vmmc-supply = <&vcc_sd3>;
-	status = "okay";
-};
-
-&usdhc4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc4>;
-	cd-gpios = <&gpio6 21 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio6 20 GPIO_ACTIVE_HIGH>;
-	status = "okay";
-};
-
-&wdog1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_wdog>;
-	fsl,ext-reset-output;
-};
-
-&iomuxc {
-	imx6x-sdb {
-		pinctrl_audmux: audmuxgrp {
-			fsl,pins = <
-				MX6SX_PAD_CSI_DATA00__AUDMUX_AUD6_TXC	0x130b0
-				MX6SX_PAD_CSI_DATA01__AUDMUX_AUD6_TXFS	0x130b0
-				MX6SX_PAD_CSI_HSYNC__AUDMUX_AUD6_TXD	0x120b0
-				MX6SX_PAD_CSI_VSYNC__AUDMUX_AUD6_RXD	0x130b0
-				MX6SX_PAD_CSI_PIXCLK__AUDMUX_MCLK	0x130b0
-			>;
-		};
-
-		pinctrl_enet1: enet1grp {
-			fsl,pins = <
-				MX6SX_PAD_ENET1_MDIO__ENET1_MDIO	0xa0b1
-				MX6SX_PAD_ENET1_MDC__ENET1_MDC		0xa0b1
-				MX6SX_PAD_RGMII1_TXC__ENET1_RGMII_TXC	0xa0b1
-				MX6SX_PAD_RGMII1_TD0__ENET1_TX_DATA_0	0xa0b1
-				MX6SX_PAD_RGMII1_TD1__ENET1_TX_DATA_1	0xa0b1
-				MX6SX_PAD_RGMII1_TD2__ENET1_TX_DATA_2	0xa0b1
-				MX6SX_PAD_RGMII1_TD3__ENET1_TX_DATA_3	0xa0b1
-				MX6SX_PAD_RGMII1_TX_CTL__ENET1_TX_EN	0xa0b1
-				MX6SX_PAD_RGMII1_RXC__ENET1_RX_CLK	0x3081
-				MX6SX_PAD_RGMII1_RD0__ENET1_RX_DATA_0	0x3081
-				MX6SX_PAD_RGMII1_RD1__ENET1_RX_DATA_1	0x3081
-				MX6SX_PAD_RGMII1_RD2__ENET1_RX_DATA_2	0x3081
-				MX6SX_PAD_RGMII1_RD3__ENET1_RX_DATA_3	0x3081
-				MX6SX_PAD_RGMII1_RX_CTL__ENET1_RX_EN	0x3081
-				MX6SX_PAD_ENET2_RX_CLK__ENET2_REF_CLK_25M	0x91
-				/* phy reset */
-				MX6SX_PAD_ENET2_CRS__GPIO2_IO_7		0x10b0
-			>;
-		};
-
-		pinctrl_enet_3v3: enet3v3grp {
-			fsl,pins = <
-				MX6SX_PAD_ENET2_COL__GPIO2_IO_6		0x80000000
-			>;
-		};
-
-		pinctrl_enet2: enet2grp {
-			fsl,pins = <
-				MX6SX_PAD_RGMII2_TXC__ENET2_RGMII_TXC	0xa0b9
-				MX6SX_PAD_RGMII2_TD0__ENET2_TX_DATA_0	0xa0b1
-				MX6SX_PAD_RGMII2_TD1__ENET2_TX_DATA_1	0xa0b1
-				MX6SX_PAD_RGMII2_TD2__ENET2_TX_DATA_2	0xa0b1
-				MX6SX_PAD_RGMII2_TD3__ENET2_TX_DATA_3	0xa0b1
-				MX6SX_PAD_RGMII2_TX_CTL__ENET2_TX_EN	0xa0b1
-				MX6SX_PAD_RGMII2_RXC__ENET2_RX_CLK	0x3081
-				MX6SX_PAD_RGMII2_RD0__ENET2_RX_DATA_0	0x3081
-				MX6SX_PAD_RGMII2_RD1__ENET2_RX_DATA_1	0x3081
-				MX6SX_PAD_RGMII2_RD2__ENET2_RX_DATA_2	0x3081
-				MX6SX_PAD_RGMII2_RD3__ENET2_RX_DATA_3	0x3081
-				MX6SX_PAD_RGMII2_RX_CTL__ENET2_RX_EN	0x3081
-			>;
-		};
-
-		pinctrl_flexcan1: flexcan1grp {
-			fsl,pins = <
-				MX6SX_PAD_QSPI1B_DQS__CAN1_TX		0x1b020
-				MX6SX_PAD_QSPI1A_SS1_B__CAN1_RX		0x1b020
-			>;
-		};
-
-		pinctrl_flexcan2: flexcan2grp {
-			fsl,pins = <
-				MX6SX_PAD_QSPI1B_SS1_B__CAN2_RX		0x1b020
-				MX6SX_PAD_QSPI1A_DQS__CAN2_TX		0x1b020
-			>;
-		};
-
-		pinctrl_gpio_keys: gpio_keysgrp {
-			fsl,pins = <
-				MX6SX_PAD_CSI_DATA04__GPIO1_IO_18 0x17059
-				MX6SX_PAD_CSI_DATA05__GPIO1_IO_19 0x17059
-			>;
-		};
-
-		pinctrl_hp: hpgrp {
-			fsl,pins = <
-				MX6SX_PAD_CSI_DATA03__GPIO1_IO_17 0x17059
-			>;
-		};
-
-		pinctrl_i2c1: i2c1grp {
-			fsl,pins = <
-				MX6SX_PAD_GPIO1_IO01__I2C1_SDA		0x4001b8b1
-				MX6SX_PAD_GPIO1_IO00__I2C1_SCL		0x4001b8b1
-			>;
-		};
-
-		pinctrl_i2c3: i2c3grp {
-			fsl,pins = <
-				MX6SX_PAD_KEY_ROW4__I2C3_SDA		0x4001b8b1
-				MX6SX_PAD_KEY_COL4__I2C3_SCL		0x4001b8b1
-			>;
-		};
-
-		pinctrl_i2c4: i2c4grp {
-			fsl,pins = <
-				MX6SX_PAD_CSI_DATA07__I2C4_SDA		0x4001b8b1
-				MX6SX_PAD_CSI_DATA06__I2C4_SCL		0x4001b8b1
-			>;
-		};
-
-		pinctrl_lcd: lcdgrp {
-			fsl,pins = <
-				MX6SX_PAD_LCD1_DATA00__LCDIF1_DATA_0 0x4001b0b0
-				MX6SX_PAD_LCD1_DATA01__LCDIF1_DATA_1 0x4001b0b0
-				MX6SX_PAD_LCD1_DATA02__LCDIF1_DATA_2 0x4001b0b0
-				MX6SX_PAD_LCD1_DATA03__LCDIF1_DATA_3 0x4001b0b0
-				MX6SX_PAD_LCD1_DATA04__LCDIF1_DATA_4 0x4001b0b0
-				MX6SX_PAD_LCD1_DATA05__LCDIF1_DATA_5 0x4001b0b0
-				MX6SX_PAD_LCD1_DATA06__LCDIF1_DATA_6 0x4001b0b0
-				MX6SX_PAD_LCD1_DATA07__LCDIF1_DATA_7 0x4001b0b0
-				MX6SX_PAD_LCD1_DATA08__LCDIF1_DATA_8 0x4001b0b0
-				MX6SX_PAD_LCD1_DATA09__LCDIF1_DATA_9 0x4001b0b0
-				MX6SX_PAD_LCD1_DATA10__LCDIF1_DATA_10 0x4001b0b0
-				MX6SX_PAD_LCD1_DATA11__LCDIF1_DATA_11 0x4001b0b0
-				MX6SX_PAD_LCD1_DATA12__LCDIF1_DATA_12 0x4001b0b0
-				MX6SX_PAD_LCD1_DATA13__LCDIF1_DATA_13 0x4001b0b0
-				MX6SX_PAD_LCD1_DATA14__LCDIF1_DATA_14 0x4001b0b0
-				MX6SX_PAD_LCD1_DATA15__LCDIF1_DATA_15 0x4001b0b0
-				MX6SX_PAD_LCD1_DATA16__LCDIF1_DATA_16 0x4001b0b0
-				MX6SX_PAD_LCD1_DATA17__LCDIF1_DATA_17 0x4001b0b0
-				MX6SX_PAD_LCD1_DATA18__LCDIF1_DATA_18 0x4001b0b0
-				MX6SX_PAD_LCD1_DATA19__LCDIF1_DATA_19 0x4001b0b0
-				MX6SX_PAD_LCD1_DATA20__LCDIF1_DATA_20 0x4001b0b0
-				MX6SX_PAD_LCD1_DATA21__LCDIF1_DATA_21 0x4001b0b0
-				MX6SX_PAD_LCD1_DATA22__LCDIF1_DATA_22 0x4001b0b0
-				MX6SX_PAD_LCD1_DATA23__LCDIF1_DATA_23 0x4001b0b0
-				MX6SX_PAD_LCD1_CLK__LCDIF1_CLK	0x4001b0b0
-				MX6SX_PAD_LCD1_ENABLE__LCDIF1_ENABLE 0x4001b0b0
-				MX6SX_PAD_LCD1_VSYNC__LCDIF1_VSYNC 0x4001b0b0
-				MX6SX_PAD_LCD1_HSYNC__LCDIF1_HSYNC 0x4001b0b0
-				MX6SX_PAD_LCD1_RESET__GPIO3_IO_27 0x4001b0b0
-			>;
-		};
-
-		pinctrl_mqs: mqsgrp {
-			fsl,pins = <
-				MX6SX_PAD_SD2_CLK__MQS_RIGHT 0x120b0
-				MX6SX_PAD_SD2_CMD__MQS_LEFT  0x120b0
-			>;
-		};
-
-		pinctrl_pcie: pciegrp {
-			fsl,pins = <
-				MX6SX_PAD_ENET1_COL__GPIO2_IO_0 0x10b0
-			>;
-		};
-
-		pinctrl_pcie_reg: pciereggrp {
-			fsl,pins = <
-				MX6SX_PAD_ENET1_CRS__GPIO2_IO_1	0x10b0
-			>;
-		};
-
-		pinctrl_peri_3v3: peri3v3grp {
-			fsl,pins = <
-				MX6SX_PAD_QSPI1A_DATA0__GPIO4_IO_16	0x80000000
-			>;
-		};
-
-		pinctrl_pwm3: pwm3grp-1 {
-			fsl,pins = <
-				MX6SX_PAD_SD1_DATA2__PWM3_OUT 0x110b0
-			>;
-		};
-
-		pinctrl_qspi2: qspi2grp {
-			fsl,pins = <
-				MX6SX_PAD_NAND_WP_B__QSPI2_A_DATA_0     0x70f1
-				MX6SX_PAD_NAND_READY_B__QSPI2_A_DATA_1  0x70f1
-				MX6SX_PAD_NAND_CE0_B__QSPI2_A_DATA_2    0x70f1
-				MX6SX_PAD_NAND_CE1_B__QSPI2_A_DATA_3    0x70f1
-				MX6SX_PAD_NAND_CLE__QSPI2_A_SCLK        0x70f1
-				MX6SX_PAD_NAND_ALE__QSPI2_A_SS0_B       0x70f1
-				MX6SX_PAD_NAND_DATA01__QSPI2_B_DATA_0   0x70f1
-				MX6SX_PAD_NAND_DATA00__QSPI2_B_DATA_1   0x70f1
-				MX6SX_PAD_NAND_WE_B__QSPI2_B_DATA_2     0x70f1
-				MX6SX_PAD_NAND_RE_B__QSPI2_B_DATA_3     0x70f1
-				MX6SX_PAD_NAND_DATA02__QSPI2_B_SCLK     0x70f1
-				MX6SX_PAD_NAND_DATA03__QSPI2_B_SS0_B    0x70f1
-			>;
-		};
-
-		pinctrl_vcc_sd3: vccsd3grp {
-			fsl,pins = <
-				MX6SX_PAD_KEY_COL1__GPIO2_IO_11		0x17059
-			>;
-		};
-
-		pinctrl_sai1: sai1grp {
-			fsl,pins = <
-				MX6SX_PAD_CSI_DATA00__SAI1_TX_BCLK	0x130b0
-				MX6SX_PAD_CSI_DATA01__SAI1_TX_SYNC	0x130b0
-				MX6SX_PAD_CSI_HSYNC__SAI1_TX_DATA_0	0x120b0
-				MX6SX_PAD_CSI_VSYNC__SAI1_RX_DATA_0	0x130b0
-				MX6SX_PAD_CSI_PIXCLK__AUDMUX_MCLK	0x130b0
-			>;
-		};
-
-		pinctrl_spdif: spdifgrp {
-			fsl,pins = <
-				MX6SX_PAD_SD4_DATA4__SPDIF_OUT          0x1b0b0
-			>;
-		};
-
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX6SX_PAD_GPIO1_IO04__UART1_DCE_TX	0x1b0b1
-				MX6SX_PAD_GPIO1_IO05__UART1_DCE_RX	0x1b0b1
-			>;
-		};
-
-		pinctrl_uart5: uart5grp {
-			fsl,pins = <
-				MX6SX_PAD_KEY_ROW3__UART5_DCE_RX	0x1b0b1
-				MX6SX_PAD_KEY_COL3__UART5_DCE_TX	0x1b0b1
-				MX6SX_PAD_KEY_ROW2__UART5_DCE_CTS	0x1b0b1
-				MX6SX_PAD_KEY_COL2__UART5_DCE_RTS	0x1b0b1
-			>;
-		};
-
-		pinctrl_usb_otg1: usbotg1grp {
-			fsl,pins = <
-				MX6SX_PAD_GPIO1_IO09__GPIO1_IO_9	0x10b0
-			>;
-		};
-
-		pinctrl_usb_otg1_id: usbotg1idgrp {
-			fsl,pins = <
-				MX6SX_PAD_GPIO1_IO10__ANATOP_OTG1_ID	0x17059
-			>;
-		};
-
-		pinctrl_usb_otg2: usbot2ggrp {
-			fsl,pins = <
-				MX6SX_PAD_GPIO1_IO12__GPIO1_IO_12	0x10b0
-			>;
-		};
-
-		pinctrl_usdhc2: usdhc2grp {
-			fsl,pins = <
-				MX6SX_PAD_SD2_CMD__USDHC2_CMD		0x17059
-				MX6SX_PAD_SD2_CLK__USDHC2_CLK		0x10059
-				MX6SX_PAD_SD2_DATA0__USDHC2_DATA0	0x17059
-				MX6SX_PAD_SD2_DATA1__USDHC2_DATA1	0x17059
-				MX6SX_PAD_SD2_DATA2__USDHC2_DATA2	0x17059
-				MX6SX_PAD_SD2_DATA3__USDHC2_DATA3	0x17059
-			>;
-		};
-
-		pinctrl_usdhc3: usdhc3grp {
-			fsl,pins = <
-				MX6SX_PAD_SD3_CMD__USDHC3_CMD		0x17059
-				MX6SX_PAD_SD3_CLK__USDHC3_CLK		0x10059
-				MX6SX_PAD_SD3_DATA0__USDHC3_DATA0	0x17059
-				MX6SX_PAD_SD3_DATA1__USDHC3_DATA1	0x17059
-				MX6SX_PAD_SD3_DATA2__USDHC3_DATA2	0x17059
-				MX6SX_PAD_SD3_DATA3__USDHC3_DATA3	0x17059
-				MX6SX_PAD_SD3_DATA4__USDHC3_DATA4	0x17059
-				MX6SX_PAD_SD3_DATA5__USDHC3_DATA5	0x17059
-				MX6SX_PAD_SD3_DATA6__USDHC3_DATA6	0x17059
-				MX6SX_PAD_SD3_DATA7__USDHC3_DATA7	0x17059
-				MX6SX_PAD_KEY_COL0__GPIO2_IO_10		0x17059 /* CD */
-				MX6SX_PAD_KEY_ROW0__GPIO2_IO_15		0x17059 /* WP */
-			>;
-		};
-
-		pinctrl_usdhc3_100mhz: usdhc3grp-100mhz {
-			fsl,pins = <
-				MX6SX_PAD_SD3_CMD__USDHC3_CMD		0x170b9
-				MX6SX_PAD_SD3_CLK__USDHC3_CLK		0x100b9
-				MX6SX_PAD_SD3_DATA0__USDHC3_DATA0	0x170b9
-				MX6SX_PAD_SD3_DATA1__USDHC3_DATA1	0x170b9
-				MX6SX_PAD_SD3_DATA2__USDHC3_DATA2	0x170b9
-				MX6SX_PAD_SD3_DATA3__USDHC3_DATA3	0x170b9
-				MX6SX_PAD_SD3_DATA4__USDHC3_DATA4	0x170b9
-				MX6SX_PAD_SD3_DATA5__USDHC3_DATA5	0x170b9
-				MX6SX_PAD_SD3_DATA6__USDHC3_DATA6	0x170b9
-				MX6SX_PAD_SD3_DATA7__USDHC3_DATA7	0x170b9
-			>;
-		};
-
-		pinctrl_usdhc3_200mhz: usdhc3grp-200mhz {
-			fsl,pins = <
-				MX6SX_PAD_SD3_CMD__USDHC3_CMD		0x170f9
-				MX6SX_PAD_SD3_CLK__USDHC3_CLK		0x100f9
-				MX6SX_PAD_SD3_DATA0__USDHC3_DATA0	0x170f9
-				MX6SX_PAD_SD3_DATA1__USDHC3_DATA1	0x170f9
-				MX6SX_PAD_SD3_DATA2__USDHC3_DATA2	0x170f9
-				MX6SX_PAD_SD3_DATA3__USDHC3_DATA3	0x170f9
-				MX6SX_PAD_SD3_DATA4__USDHC3_DATA4	0x170f9
-				MX6SX_PAD_SD3_DATA5__USDHC3_DATA5	0x170f9
-				MX6SX_PAD_SD3_DATA6__USDHC3_DATA6	0x170f9
-				MX6SX_PAD_SD3_DATA7__USDHC3_DATA7	0x170f9
-			>;
-		};
-
-		pinctrl_usdhc4: usdhc4grp {
-			fsl,pins = <
-				MX6SX_PAD_SD4_CMD__USDHC4_CMD		0x17059
-				MX6SX_PAD_SD4_CLK__USDHC4_CLK		0x10059
-				MX6SX_PAD_SD4_DATA0__USDHC4_DATA0	0x17059
-				MX6SX_PAD_SD4_DATA1__USDHC4_DATA1	0x17059
-				MX6SX_PAD_SD4_DATA2__USDHC4_DATA2	0x17059
-				MX6SX_PAD_SD4_DATA3__USDHC4_DATA3	0x17059
-				MX6SX_PAD_SD4_DATA7__GPIO6_IO_21	0x17059 /* CD */
-				MX6SX_PAD_SD4_DATA6__GPIO6_IO_20	0x17059 /* WP */
-			>;
-		};
-
-		pinctrl_wdog: wdoggrp {
-			fsl,pins = <
-				MX6SX_PAD_GPIO1_IO13__WDOG1_WDOG_ANY 0x30b0
-			>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi b/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi
deleted file mode 100644
index 47d3ce5d255f..000000000000
--- a/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi
+++ /dev/null
@@ -1,41 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2018 Kontron Electronics GmbH
- * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
- */
-
-#include "imx6ul.dtsi"
-#include "imx6ul-kontron-n6x1x-som-common.dtsi"
-
-/ {
-	model = "Kontron N6310 SOM";
-	compatible = "kontron,imx6ul-n6310-som", "fsl,imx6ul";
-
-	memory@80000000 {
-		reg = <0x80000000 0x10000000>;
-		device_type = "memory";
-	};
-};
-
-&qspi {
-	spi-flash@0 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "spi-nand";
-		spi-max-frequency = <108000000>;
-		spi-tx-bus-width = <4>;
-		spi-rx-bus-width = <4>;
-		reg = <0>;
-
-		partition@0 {
-			label = "ubi1";
-			reg = <0x00000000 0x08000000>;
-		};
-
-		partition@8000000 {
-			label = "ubi2";
-			reg = <0x08000000 0x08000000>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6311-s.dts b/arch/arm/boot/dts/imx6ul-kontron-n6311-s.dts
deleted file mode 100644
index 239a1af3aeaa..000000000000
--- a/arch/arm/boot/dts/imx6ul-kontron-n6311-s.dts
+++ /dev/null
@@ -1,16 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2018 Kontron Electronics GmbH
- */
-
-/dts-v1/;
-
-#include "imx6ul-kontron-n6311-som.dtsi"
-#include "imx6ul-kontron-n6x1x-s.dtsi"
-
-/ {
-	model = "Kontron N6311 S";
-	compatible = "kontron,imx6ul-n6311-s", "kontron,imx6ul-n6311-som",
-		     "fsl,imx6ul";
-};
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6311-som.dtsi b/arch/arm/boot/dts/imx6ul-kontron-n6311-som.dtsi
deleted file mode 100644
index a095a7654ac6..000000000000
--- a/arch/arm/boot/dts/imx6ul-kontron-n6311-som.dtsi
+++ /dev/null
@@ -1,40 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2018 Kontron Electronics GmbH
- */
-
-#include "imx6ul.dtsi"
-#include "imx6ul-kontron-n6x1x-som-common.dtsi"
-
-/ {
-	model = "Kontron N6311 SOM";
-	compatible = "kontron,imx6ul-n6311-som", "fsl,imx6ul";
-
-	memory@80000000 {
-		reg = <0x80000000 0x20000000>;
-		device_type = "memory";
-	};
-};
-
-&qspi {
-	spi-flash@0 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "spi-nand";
-		spi-max-frequency = <104000000>;
-		spi-tx-bus-width = <4>;
-		spi-rx-bus-width = <4>;
-		reg = <0>;
-
-		partition@0 {
-			label = "ubi1";
-			reg = <0x00000000 0x08000000>;
-		};
-
-		partition@8000000 {
-			label = "ubi2";
-			reg = <0x08000000 0x18000000>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx6ul-tx6ul-0010.dts b/arch/arm/boot/dts/imx6ul-tx6ul-0010.dts
deleted file mode 100644
index 8c2f3df79b47..000000000000
--- a/arch/arm/boot/dts/imx6ul-tx6ul-0010.dts
+++ /dev/null
@@ -1,53 +0,0 @@
-/*
- * Copyright 2015 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6ul.dtsi"
-#include "imx6ul-tx6ul.dtsi"
-
-/ {
-	model = "Ka-Ro electronics TXUL-0010 Module";
-	compatible = "karo,imx6ul-tx6ul", "fsl,imx6ul";
-
-	aliases {
-		/delete-property/ mmc1;
-	};
-};
diff --git a/arch/arm/boot/dts/imx6ul-tx6ul-0011.dts b/arch/arm/boot/dts/imx6ul-tx6ul-0011.dts
deleted file mode 100644
index d82698e7d50f..000000000000
--- a/arch/arm/boot/dts/imx6ul-tx6ul-0011.dts
+++ /dev/null
@@ -1,68 +0,0 @@
-/*
- * Copyright 2015 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "imx6ul.dtsi"
-#include "imx6ul-tx6ul.dtsi"
-
-/ {
-	model = "Ka-Ro electronics TXUL-0011 Module";
-	compatible = "karo,imx6ul-tx6ul", "fsl,imx6ul";
-
-	aliases {
-		mmc0 = &usdhc2;
-		mmc1 = &usdhc1;
-	};
-};
-
-&gpmi {
-	status = "disabled";
-};
-
-&usdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc2>;
-	bus-width = <4>;
-	no-1-8-v;
-	non-removable;
-	fsl,wp-controller;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dts b/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dts
deleted file mode 100644
index 08669a18349e..000000000000
--- a/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dts
+++ /dev/null
@@ -1,14 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
-/*
- * Copyright 2018 Toradex AG
- */
-
-/dts-v1/;
-
-#include "imx6ull-colibri-nonwifi.dtsi"
-#include "imx6ull-colibri-eval-v3.dtsi"
-
-/ {
-	model = "Toradex Colibri iMX6ULL 256MB on Colibri Evaluation Board V3";
-	compatible = "toradex,colibri-imx6ull-eval", "fsl,imx6ull";
-};
diff --git a/arch/arm/boot/dts/imx6ull-colibri-nonwifi.dtsi b/arch/arm/boot/dts/imx6ull-colibri-nonwifi.dtsi
deleted file mode 100644
index 95a11b8bcbdb..000000000000
--- a/arch/arm/boot/dts/imx6ull-colibri-nonwifi.dtsi
+++ /dev/null
@@ -1,24 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
-/*
- * Copyright 2018 Toradex AG
- */
-
-#include "imx6ull-colibri.dtsi"
-
-/ {
-	memory@80000000 {
-		device_type = "memory";
-		reg = <0x80000000 0x10000000>;
-	};
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_gpio1 &pinctrl_gpio2 &pinctrl_gpio3
-		&pinctrl_gpio4 &pinctrl_gpio5 &pinctrl_gpio6 &pinctrl_gpio7>;
-};
-
-&iomuxc_snvs {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_snvs_gpio1 &pinctrl_snvs_gpio2 &pinctrl_snvs_gpio3>;
-};
diff --git a/arch/arm/boot/dts/imx6ull-colibri-wifi-eval-v3.dts b/arch/arm/boot/dts/imx6ull-colibri-wifi-eval-v3.dts
deleted file mode 100644
index df72ce1ae2cb..000000000000
--- a/arch/arm/boot/dts/imx6ull-colibri-wifi-eval-v3.dts
+++ /dev/null
@@ -1,14 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
-/*
- * Copyright 2018 Toradex AG
- */
-
-/dts-v1/;
-
-#include "imx6ull-colibri-wifi.dtsi"
-#include "imx6ull-colibri-eval-v3.dtsi"
-
-/ {
-	model = "Toradex Colibri iMX6ULL 512MB on Colibri Evaluation Board V3";
-	compatible = "toradex,colibri-imx6ull-wifi-eval", "fsl,imx6ull";
-};
diff --git a/arch/arm/boot/dts/imx6ull-colibri-wifi.dtsi b/arch/arm/boot/dts/imx6ull-colibri-wifi.dtsi
deleted file mode 100644
index 9f1e38282bee..000000000000
--- a/arch/arm/boot/dts/imx6ull-colibri-wifi.dtsi
+++ /dev/null
@@ -1,53 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
-/*
- * Copyright 2018 Toradex AG
- */
-
-#include "imx6ull-colibri.dtsi"
-
-/ {
-	memory@80000000 {
-		device_type = "memory";
-		reg = <0x80000000 0x20000000>;
-	};
-
-	wifi_pwrseq: sdio-pwrseq {
-		compatible = "mmc-pwrseq-simple";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_snvs_wifi_pdn>;
-		reset-gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
-	};
-};
-
-&cpu0 {
-	clock-frequency = <792000000>;
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_gpio1 &pinctrl_gpio2 &pinctrl_gpio3
-		&pinctrl_gpio4 &pinctrl_gpio5 &pinctrl_gpio7>;
-
-};
-
-&iomuxc_snvs {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_snvs_gpio1 &pinctrl_snvs_gpio2>;
-};
-
-&usdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc2>;
-	assigned-clocks = <&clks IMX6UL_CLK_USDHC2_SEL>, <&clks IMX6UL_CLK_USDHC2>;
-	assigned-clock-parents = <&clks IMX6UL_CLK_PLL2_PFD2>;
-	assigned-clock-rates = <0>, <198000000>;
-	cap-power-off-card;
-	keep-power-in-suspend;
-	max-frequency = <25000000>;
-	mmc-pwrseq = <&wifi_pwrseq>;
-	no-1-8-v;
-	non-removable;
-	vmmc-supply = <&reg_module_3v3>;
-	wakeup-source;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6ull-kontron-n6411-s.dts b/arch/arm/boot/dts/imx6ull-kontron-n6411-s.dts
deleted file mode 100644
index 57588a5e1e34..000000000000
--- a/arch/arm/boot/dts/imx6ull-kontron-n6411-s.dts
+++ /dev/null
@@ -1,16 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2019 Kontron Electronics GmbH
- */
-
-/dts-v1/;
-
-#include "imx6ull-kontron-n6411-som.dtsi"
-#include "imx6ul-kontron-n6x1x-s.dtsi"
-
-/ {
-	model = "Kontron N6411 S";
-	compatible = "kontron,imx6ull-n6411-s", "kontron,imx6ull-n6411-som",
-		     "fsl,imx6ull";
-};
diff --git a/arch/arm/boot/dts/imx6ull-kontron-n6411-som.dtsi b/arch/arm/boot/dts/imx6ull-kontron-n6411-som.dtsi
deleted file mode 100644
index b7e984284e1a..000000000000
--- a/arch/arm/boot/dts/imx6ull-kontron-n6411-som.dtsi
+++ /dev/null
@@ -1,40 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2018 Kontron Electronics GmbH
- */
-
-#include "imx6ull.dtsi"
-#include "imx6ul-kontron-n6x1x-som-common.dtsi"
-
-/ {
-	model = "Kontron N6411 SOM";
-	compatible = "kontron,imx6ull-n6311-som", "fsl,imx6ull";
-
-	memory@80000000 {
-		reg = <0x80000000 0x20000000>;
-		device_type = "memory";
-	};
-};
-
-&qspi {
-	spi-flash@0 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "spi-nand";
-		spi-max-frequency = <104000000>;
-		spi-tx-bus-width = <4>;
-		spi-rx-bus-width = <4>;
-		reg = <0>;
-
-		partition@0 {
-			label = "ubi1";
-			reg = <0x00000000 0x08000000>;
-		};
-
-		partition@8000000 {
-			label = "ubi2";
-			reg = <0x08000000 0x18000000>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx7-colibri-aster.dtsi b/arch/arm/boot/dts/imx7-colibri-aster.dtsi
deleted file mode 100644
index b770fc937970..000000000000
--- a/arch/arm/boot/dts/imx7-colibri-aster.dtsi
+++ /dev/null
@@ -1,169 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
-/*
- * Copyright 2017-2020 Toradex AG
- *
- */
-
-
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pwm/pwm.h>
-
-/ {
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpiokeys>;
-
-		power {
-			label = "Wake-Up";
-			gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
-			linux,code = <KEY_WAKEUP>;
-			debounce-interval = <10>;
-			wakeup-source;
-		};
-	};
-
-	panel: panel {
-		compatible = "edt,et057090dhu";
-		backlight = <&bl>;
-		power-supply = <&reg_3v3>;
-
-		port {
-			panel_in: endpoint {
-				remote-endpoint = <&lcdif_out>;
-			};
-		};
-	};
-
-	reg_3v3: regulator-3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "3.3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	reg_5v0: regulator-5v0 {
-		compatible = "regulator-fixed";
-		regulator-name = "5V";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-	};
-
-	reg_usbh_vbus: regulator-usbh-vbus {
-		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_usbh_reg>;
-		regulator-name = "VCC_USB[1-4]";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio4 7 GPIO_ACTIVE_LOW>;
-		vin-supply = <&reg_5v0>;
-	};
-};
-
-&adc1 {
-	status = "okay";
-};
-
-/*
- * ADC2 is not available on the Aster board and
- * conflicts with AD7879 resistive touchscreen.
- */
-&adc2 {
-	status = "disabled";
-};
-
-&bl {
-	brightness-levels = <0 4 8 16 32 64 128 255>;
-	default-brightness-level = <6>;
-	power-supply = <&reg_3v3>;
-	status = "okay";
-};
-
-&fec1 {
-	status = "okay";
-};
-
-&i2c4 {
-	status = "okay";
-
-	/* Microchip/Atmel maxtouch controller */
-	touchscreen@4a {
-		compatible = "atmel,maxtouch";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpiotouch>;
-		reg = <0x4a>;
-		interrupt-parent = <&gpio2>;
-		interrupts = <15 IRQ_TYPE_EDGE_FALLING>;	/* SODIMM 107 */
-		reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;	/* SODIMM 106 */
-	};
-
-	/* M41T0M6 real time clock on carrier board */
-	rtc: rtc@68 {
-		compatible = "st,m41t0";
-		reg = <0x68>;
-	};
-};
-
-&iomuxc {
-	pinctrl_gpiotouch: touchgpios {
-		fsl,pins = <
-			MX7D_PAD_EPDC_DATA15__GPIO2_IO15        0x74
-			MX7D_PAD_EPDC_BDR0__GPIO2_IO28          0x14
-		>;
-	};
-};
-
-&lcdif {
-	status = "okay";
-
-	port {
-		lcdif_out: endpoint {
-			remote-endpoint = <&panel_in>;
-		};
-	};
-};
-
-&pwm1 {
-	status = "okay";
-};
-
-&pwm2 {
-	status = "okay";
-};
-
-&pwm3 {
-	status = "okay";
-};
-
-&pwm4 {
-	status = "okay";
-};
-
-&uart1 {
-	status = "okay";
-};
-
-&uart2 {
-	status = "okay";
-};
-
-&uart3 {
-	status = "okay";
-};
-
-&usbotg1 {
-	status = "okay";
-};
-
-&usdhc1 {
-	keep-power-in-suspend;
-	no-1-8-v;
-	wakeup-source;
-	vmmc-supply = <&reg_3v3>;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi b/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
deleted file mode 100644
index 3b9df8c82ae3..000000000000
--- a/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
+++ /dev/null
@@ -1,194 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
-/*
- * Copyright 2016-2020 Toradex
- */
-
-/ {
-	aliases {
-		rtc0 = &rtc;
-		rtc1 = &snvs_rtc;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	/* fixed crystal dedicated to mpc258x */
-	clk16m: clk16m {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <16000000>;
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpiokeys>;
-
-		power {
-			label = "Wake-Up";
-			gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
-			linux,code = <KEY_WAKEUP>;
-			debounce-interval = <10>;
-			wakeup-source;
-		};
-	};
-
-	panel: panel {
-		compatible = "edt,et057090dhu";
-		backlight = <&bl>;
-		power-supply = <&reg_3v3>;
-
-		port {
-			panel_in: endpoint {
-				remote-endpoint = <&lcdif_out>;
-			};
-		};
-	};
-
-	reg_3v3: regulator-3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "3.3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	reg_5v0: regulator-5v0 {
-		compatible = "regulator-fixed";
-		regulator-name = "5V";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-	};
-
-	reg_usbh_vbus: regulator-usbh-vbus {
-		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_usbh_reg>;
-		regulator-name = "VCC_USB[1-4]";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio4 7 GPIO_ACTIVE_LOW>;
-		vin-supply = <&reg_5v0>;
-	};
-};
-
-&bl {
-	brightness-levels = <0 4 8 16 32 64 128 255>;
-	default-brightness-level = <6>;
-	power-supply = <&reg_3v3>;
-
-	status = "okay";
-};
-
-&adc1 {
-	status = "okay";
-};
-
-&adc2 {
-	status = "okay";
-};
-
-&ecspi3 {
-	status = "okay";
-
-	mcp2515: can@0 {
-		compatible = "microchip,mcp2515";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_can_int>;
-		reg = <0>;
-		clocks = <&clk16m>;
-		interrupt-parent = <&gpio5>;
-		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
-		spi-max-frequency = <10000000>;
-		vdd-supply = <&reg_3v3>;
-		xceiver-supply = <&reg_5v0>;
-		status = "okay";
-	};
-};
-
-&fec1 {
-	status = "okay";
-};
-
-&i2c4 {
-	status = "okay";
-
-	/*
-	 * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
-	 * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
-	 */
-	touchscreen@4a {
-		compatible = "atmel,maxtouch";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpiotouch>;
-		reg = <0x4a>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;		/* SODIMM 28 */
-		reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;	/* SODIMM 30 */
-		status = "disabled";
-	};
-
-	/* M41T0M6 real time clock on carrier board */
-	rtc: rtc@68 {
-		compatible = "st,m41t0";
-		reg = <0x68>;
-	};
-};
-
-&lcdif {
-	status = "okay";
-
-	port {
-		lcdif_out: endpoint {
-			remote-endpoint = <&panel_in>;
-		};
-	};
-};
-
-&pwm1 {
-	status = "okay";
-};
-
-&pwm2 {
-	status = "okay";
-};
-
-&pwm3 {
-	status = "okay";
-};
-
-&pwm4 {
-	status = "okay";
-};
-
-&uart1 {
-	status = "okay";
-};
-
-&uart2 {
-	status = "okay";
-};
-
-&uart3 {
-	status = "okay";
-};
-
-&usbotg1 {
-	status = "okay";
-};
-
-&usdhc1 {
-	keep-power-in-suspend;
-	wakeup-source;
-	vmmc-supply = <&reg_3v3>;
-	status = "okay";
-};
-
-&iomuxc {
-	pinctrl_gpiotouch: touchgpios {
-		fsl,pins = <
-			MX7D_PAD_GPIO1_IO09__GPIO1_IO9		0x74
-			MX7D_PAD_GPIO1_IO10__GPIO1_IO10		0x14
-		>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx7d-colibri-aster.dts b/arch/arm/boot/dts/imx7d-colibri-aster.dts
deleted file mode 100644
index f3f0537d5a37..000000000000
--- a/arch/arm/boot/dts/imx7d-colibri-aster.dts
+++ /dev/null
@@ -1,20 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
-/*
- * Copyright 2017-2020 Toradex AG
- *
- */
-
-/dts-v1/;
-#include "imx7d-colibri.dtsi"
-#include "imx7-colibri-aster.dtsi"
-
-/ {
-	model = "Toradex Colibri iMX7D on Aster Carrier Board";
-	compatible = "toradex,colibri-imx7d-aster", "toradex,colibri-imx7d",
-		     "fsl,imx7d";
-};
-
-&usbotg2 {
-	vbus-supply = <&reg_usbh_vbus>;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx7d-colibri-eval-v3.dts b/arch/arm/boot/dts/imx7d-colibri-eval-v3.dts
deleted file mode 100644
index 87b132bcd272..000000000000
--- a/arch/arm/boot/dts/imx7d-colibri-eval-v3.dts
+++ /dev/null
@@ -1,19 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
-/*
- * Copyright 2016-2020 Toradex
- */
-
-/dts-v1/;
-#include "imx7d-colibri.dtsi"
-#include "imx7-colibri-eval-v3.dtsi"
-
-/ {
-	model = "Toradex Colibri iMX7D on Colibri Evaluation Board V3";
-	compatible = "toradex,colibri-imx7d-eval-v3", "toradex,colibri-imx7d",
-		     "fsl,imx7d";
-};
-
-&usbotg2 {
-	vbus-supply = <&reg_usbh_vbus>;
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx7d-colibri.dtsi b/arch/arm/boot/dts/imx7d-colibri.dtsi
deleted file mode 100644
index 219a0404a058..000000000000
--- a/arch/arm/boot/dts/imx7d-colibri.dtsi
+++ /dev/null
@@ -1,26 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
-/*
- * Copyright 2016-2020 Toradex
- */
-
-#include "imx7d.dtsi"
-#include "imx7-colibri.dtsi"
-
-/ {
-	memory@80000000 {
-		device_type = "memory";
-		reg = <0x80000000 0x20000000>;
-	};
-};
-
-&cpu1 {
-	cpu-supply = <&reg_DCDC2>;
-};
-
-&gpmi {
-	status = "okay";
-};
-
-&usbotg2 {
-	dr_mode = "host";
-};
diff --git a/arch/arm/boot/dts/imx7d-mba7.dts b/arch/arm/boot/dts/imx7d-mba7.dts
deleted file mode 100644
index 32bf9fa9d00e..000000000000
--- a/arch/arm/boot/dts/imx7d-mba7.dts
+++ /dev/null
@@ -1,113 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0 OR X11
-/*
- * Device Tree Source for TQ-Systems TQMa7D board on MBa7 carrier board.
- *
- * Copyright (C) 2016 TQ-Systems GmbH
- * Author: Markus Niebel <Markus.Niebel@tq-group.com>
- * Copyright (C) 2019 Bruno Thomsen <bruno.thomsen@gmail.com>
- */
-
-/dts-v1/;
-
-#include "imx7d-tqma7.dtsi"
-#include "imx7-mba7.dtsi"
-
-/ {
-	model = "TQ-Systems TQMa7D board on MBa7 carrier board";
-	compatible = "tq,imx7d-mba7", "tq,imx7d-tqma7", "fsl,imx7d";
-};
-
-&fec2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet2>;
-	phy-mode = "rgmii-id";
-	phy-reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
-	phy-reset-duration = <1>;
-	phy-supply = <&reg_fec2_pwdn>;
-	phy-handle = <&ethphy2_0>;
-	fsl,magic-packet;
-	status = "okay";
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		ethphy2_0: ethernet-phy@0 {
-			compatible = "ethernet-phy-ieee802.3-c22";
-			reg = <0>;
-			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
-			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
-			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
-			ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
-		};
-	};
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_hog_mba7_1>;
-
-	pinctrl_enet2: enet2grp {
-		fsl,pins = <
-			MX7D_PAD_SD2_CD_B__ENET2_MDIO			0x02
-			MX7D_PAD_SD2_WP__ENET2_MDC			0x00
-			MX7D_PAD_EPDC_GDSP__ENET2_RGMII_TXC		0x71
-			MX7D_PAD_EPDC_SDCE2__ENET2_RGMII_TD0		0x71
-			MX7D_PAD_EPDC_SDCE3__ENET2_RGMII_TD1		0x71
-			MX7D_PAD_EPDC_GDCLK__ENET2_RGMII_TD2		0x71
-			MX7D_PAD_EPDC_GDOE__ENET2_RGMII_TD3		0x71
-			MX7D_PAD_EPDC_GDRL__ENET2_RGMII_TX_CTL		0x71
-			MX7D_PAD_EPDC_SDCE1__ENET2_RGMII_RXC		0x79
-			MX7D_PAD_EPDC_SDCLK__ENET2_RGMII_RD0		0x79
-			MX7D_PAD_EPDC_SDLE__ENET2_RGMII_RD1		0x79
-			MX7D_PAD_EPDC_SDOE__ENET2_RGMII_RD2		0x79
-			MX7D_PAD_EPDC_SDSHR__ENET2_RGMII_RD3		0x79
-			MX7D_PAD_EPDC_SDCE0__ENET2_RGMII_RX_CTL		0x79
-			/* Reset: SION, 100kPU, SRE_FAST, DSE_X1 */
-			MX7D_PAD_EPDC_BDR0__GPIO2_IO28		0x40000070
-			/* INT/PWDN: SION, 100kPU, HYS, SRE_FAST, DSE_X1 */
-			MX7D_PAD_EPDC_PWR_STAT__GPIO2_IO31	0x40000078
-		>;
-	};
-
-	pinctrl_pcie: pciegrp {
-		fsl,pins = <
-			/* #pcie_wake */
-			MX7D_PAD_EPDC_PWR_COM__GPIO2_IO30		0x70
-			/* #pcie_rst */
-			MX7D_PAD_SD2_CLK__GPIO5_IO12			0x70
-			/* #pcie_dis */
-			MX7D_PAD_EPDC_BDR1__GPIO2_IO29			0x70
-		>;
-	};
-};
-
-&iomuxc_lpsr {
-	pinctrl_usbotg2: usbotg2grp {
-		fsl,pins = <
-			MX7D_PAD_LPSR_GPIO1_IO06__USB_OTG2_OC	0x5c
-			MX7D_PAD_LPSR_GPIO1_IO07__GPIO1_IO7	0x59
-		>;
-	};
-};
-
-&pcie {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pcie>;
-	/* 1.5V logically from 3.3V */
-	/* probe deferral not supported */
-	/* pcie-bus-supply = <&reg_mpcie_1v5>; */
-	reset-gpio = <&gpio5 12 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-&usbotg2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbotg2>;
-	vbus-supply = <&reg_usb_otg2_vbus>;
-	srp-disable;
-	hnp-disable;
-	adp-disable;
-	dr_mode = "host";
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx7s-colibri-aster.dts b/arch/arm/boot/dts/imx7s-colibri-aster.dts
deleted file mode 100644
index fca4e0a95c1b..000000000000
--- a/arch/arm/boot/dts/imx7s-colibri-aster.dts
+++ /dev/null
@@ -1,15 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
-/*
- * Copyright 2017-2020 Toradex AG
- *
- */
-
-/dts-v1/;
-#include "imx7s-colibri.dtsi"
-#include "imx7-colibri-aster.dtsi"
-
-/ {
-	model = "Toradex Colibri iMX7S on Aster Carrier Board";
-	compatible = "toradex,colibri-imx7s-aster", "toradex,colibri-imx7s",
-		     "fsl,imx7s";
-};
diff --git a/arch/arm/boot/dts/imx7s-colibri-eval-v3.dts b/arch/arm/boot/dts/imx7s-colibri-eval-v3.dts
deleted file mode 100644
index aa70d3f2e2e2..000000000000
--- a/arch/arm/boot/dts/imx7s-colibri-eval-v3.dts
+++ /dev/null
@@ -1,14 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
-/*
- * Copyright 2016-2020 Toradex
- */
-
-/dts-v1/;
-#include "imx7s-colibri.dtsi"
-#include "imx7-colibri-eval-v3.dtsi"
-
-/ {
-	model = "Toradex Colibri iMX7S on Colibri Evaluation Board V3";
-	compatible = "toradex,colibri-imx7s-eval-v3", "toradex,colibri-imx7s",
-		     "fsl,imx7s";
-};
diff --git a/arch/arm/boot/dts/intel/Makefile b/arch/arm/boot/dts/intel/Makefile
new file mode 100644
index 000000000000..c5fc845deb61
--- /dev/null
+++ b/arch/arm/boot/dts/intel/Makefile
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0
+subdir-y += axm
+subdir-y += ixp
+subdir-y += pxa
+subdir-y += socfpga
diff --git a/arch/arm/boot/dts/intel/axm/Makefile b/arch/arm/boot/dts/intel/axm/Makefile
new file mode 100644
index 000000000000..7c7dc679964d
--- /dev/null
+++ b/arch/arm/boot/dts/intel/axm/Makefile
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_AXXIA) += \
+	axm5516-amarillo.dtb
+dtb-$(CONFIG_ARCH_AXXIA) += \
+	axm5516-amarillo.dtb
diff --git a/arch/arm/boot/dts/axm5516-amarillo.dts b/arch/arm/boot/dts/intel/axm/axm5516-amarillo.dts
index 2e2ad3c7ee77..2e2ad3c7ee77 100644
--- a/arch/arm/boot/dts/axm5516-amarillo.dts
+++ b/arch/arm/boot/dts/intel/axm/axm5516-amarillo.dts
diff --git a/arch/arm/boot/dts/axm5516-cpus.dtsi b/arch/arm/boot/dts/intel/axm/axm5516-cpus.dtsi
index 3bcf4e0a3c85..f13ef80b6637 100644
--- a/arch/arm/boot/dts/axm5516-cpus.dtsi
+++ b/arch/arm/boot/dts/intel/axm/axm5516-cpus.dtsi
@@ -73,7 +73,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x00>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -81,7 +81,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x01>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -89,7 +89,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x02>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -97,7 +97,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x03>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -105,7 +105,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x100>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -113,7 +113,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x101>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -121,7 +121,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x102>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -129,7 +129,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x103>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -137,7 +137,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x200>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -145,7 +145,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x201>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -153,7 +153,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x202>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -161,7 +161,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x203>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -169,7 +169,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x300>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -177,7 +177,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x301>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -185,7 +185,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x302>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -193,7 +193,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x303>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 	};
diff --git a/arch/arm/boot/dts/axm55xx.dtsi b/arch/arm/boot/dts/intel/axm/axm55xx.dtsi
index 7676a65059a4..5277890cfad2 100644
--- a/arch/arm/boot/dts/axm55xx.dtsi
+++ b/arch/arm/boot/dts/intel/axm/axm55xx.dtsi
@@ -108,7 +108,7 @@
 			#size-cells = <2>;
 			ranges;
 
-			serial0: uart@2010080000 {
+			serial0: serial@2010080000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0x20 0x10080000 0 0x1000>;
 				interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
@@ -117,7 +117,7 @@
 				status = "disabled";
 			};
 
-			serial1: uart@2010081000 {
+			serial1: serial@2010081000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0x20 0x10081000 0 0x1000>;
 				interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
@@ -126,7 +126,7 @@
 				status = "disabled";
 			};
 
-			serial2: uart@2010082000 {
+			serial2: serial@2010082000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0x20 0x10082000 0 0x1000>;
 				interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
@@ -135,7 +135,7 @@
 				status = "disabled";
 			};
 
-			serial3: uart@2010083000 {
+			serial3: serial@2010083000 {
 				compatible = "arm,pl011", "arm,primecell";
 				reg = <0x20 0x10083000 0 0x1000>;
 				interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/intel/ixp/Makefile b/arch/arm/boot/dts/intel/ixp/Makefile
new file mode 100644
index 000000000000..cb30d8d55016
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/Makefile
@@ -0,0 +1,22 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_IXP4XX) += \
+	intel-ixp42x-actiontec-mi424wr-ac.dtb \
+	intel-ixp42x-actiontec-mi424wr-d.dtb \
+	intel-ixp42x-linksys-nslu2.dtb \
+	intel-ixp42x-linksys-wrv54g.dtb \
+	intel-ixp42x-freecom-fsg-3.dtb \
+	intel-ixp42x-welltech-epbx100.dtb \
+	intel-ixp42x-ixdp425.dtb \
+	intel-ixp43x-kixrp435.dtb \
+	intel-ixp46x-ixdp465.dtb \
+	intel-ixp42x-adi-coyote.dtb \
+	intel-ixp42x-ixdpg425.dtb \
+	intel-ixp42x-goramo-multilink.dtb \
+	intel-ixp42x-iomega-nas100d.dtb \
+	intel-ixp42x-dlink-dsm-g600.dtb \
+	intel-ixp42x-gateworks-gw2348.dtb \
+	intel-ixp43x-gateworks-gw2358.dtb \
+	intel-ixp42x-netgear-wg302v1.dtb \
+	intel-ixp42x-arcom-vulcan.dtb \
+	intel-ixp42x-gateway-7001.dtb \
+	intel-ixp42x-usrobotics-usr8200.dtb
diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-actiontec-mi424wr-ac.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-actiontec-mi424wr-ac.dts
new file mode 100644
index 000000000000..413b9255f9e3
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-actiontec-mi424wr-ac.dts
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for the IXP425-based Actiontec MI424WR revision A and C
+ * Based on a board file from OpenWrt by Jose Vasconcellos.
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x-actiontec-mi424wr.dtsi"
+
+/ {
+	model = "Actiontec MI424WR rev A/C";
+	compatible = "actiontec,mi424wr-ac", "intel,ixp42x";
+
+	soc {
+		/* EthB used for WAN */
+		ethernet@c8009000 {
+			phy-handle = <&phy17>; // 17 on revision A-C
+
+			mdio {
+				phy17: ethernet-phy@17 {
+					/* WAN */
+					reg = <17>;
+				};
+			};
+		};
+
+		/* EthC used for LAN */
+		ethernet@c800a000 {
+			/* Fixed link to the CPU MII port on the KS8995 */
+			fixed-link {
+				speed = <100>;
+				full-duplex;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-actiontec-mi424wr-d.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-actiontec-mi424wr-d.dts
new file mode 100644
index 000000000000..3619c6411a5c
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-actiontec-mi424wr-d.dts
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for the IXP425-based Actiontec MI424WR revision D
+ * Based on a board file from OpenWrt by Jose Vasconcellos.
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x-actiontec-mi424wr.dtsi"
+
+/ {
+	model = "Actiontec MI424WR rev D";
+	compatible = "actiontec,mi424wr-d", "intel,ixp42x";
+
+	soc {
+		/* EthB used for LAN */
+		ethernet@c8009000 {
+			/* Fixed link to the CPU MII port on the KS8995 */
+			fixed-link {
+				speed = <100>;
+				full-duplex;
+			};
+
+			mdio {
+				/* PHY ID 0x00221450 */
+				phy5: ethernet-phy@5 {
+					/* WAN */
+					reg = <5>;
+				};
+			};
+		};
+
+		/* EthC used for WAN */
+		ethernet@c800a000 {
+			phy-handle = <&phy5>; // 5 on revision D
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-actiontec-mi424wr.dtsi b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-actiontec-mi424wr.dtsi
new file mode 100644
index 000000000000..76fd97c5beb6
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-actiontec-mi424wr.dtsi
@@ -0,0 +1,272 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for the IXP425-based Actiontec MI424WR
+ * Based on a board file from OpenWrt by Jose Vasconcellos.
+ */
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x02000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		stdout-path = "uart1:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-wan-coax {
+			color = <LED_COLOR_ID_GREEN>;
+			function = "wan-coax";
+			gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led-power-alarm {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_ALARM;
+			gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led-power {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+		led-wireless {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_WLAN;
+			gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+		led-internet-down {
+			color = <LED_COLOR_ID_RED>;
+			function = "internet-down";
+			gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led-internet-up {
+			color = <LED_COLOR_ID_GREEN>;
+			function = "internet-up";
+			gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led-lan-coax {
+			color = <LED_COLOR_ID_GREEN>;
+			function = "lan-coax";
+			gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		led-wan-ethernet-alarm {
+			color = <LED_COLOR_ID_RED>;
+			function = "wan-ethernet-alarm";
+			gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+		/* The last three LEDs are not mounted but traces exist on the PCB */
+		led-phone-1 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = "phone-1";
+			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+		led-phone-2 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = "phone-2";
+			gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+		led-voip {
+			color = <LED_COLOR_ID_GREEN>;
+			function = "voip";
+			gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		button-reset {
+			wakeup-source;
+			linux,code = <KEY_RESTART>;
+			label = "reset";
+			gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	spi {
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sck-gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>;
+		cs-gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
+		num-chipselects = <1>;
+
+		ethernet-switch@0 {
+			compatible = "micrel,ks8995";
+			reg = <0>;
+			spi-max-frequency = <50000000>;
+
+			ethernet-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ethernet-port@0 {
+					reg = <0>;
+					label = "lan1";
+					phy-mode = "mii";
+					phy-handle = <&phy1>;
+				};
+				ethernet-port@1 {
+					reg = <1>;
+					label = "lan2";
+					phy-mode = "mii";
+					phy-handle = <&phy2>;
+				};
+				ethernet-port@2 {
+					reg = <2>;
+					label = "lan3";
+					phy-mode = "mii";
+					phy-handle = <&phy3>;
+				};
+				ethernet-port@3 {
+					reg = <3>;
+					label = "lan4";
+					phy-mode = "mii";
+					phy-handle = <&phy4>;
+				};
+				ethernet-port@4 {
+					reg = <4>;
+					ethernet = <&ethc>;
+					phy-mode = "mii";
+					fixed-link {
+						speed = <100>;
+						full-duplex;
+					};
+				};
+
+			};
+		};
+	};
+
+	soc {
+		bus@c4000000 {
+			flash@0,0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/*
+				 * 8 MB of Flash in 64 0x20000 sized blocks
+				 * mapped in at CS0.
+				 */
+				reg = <0 0x00000000 0x0800000>;
+
+				/* Configure expansion bus to allow writes */
+				intel,ixp4xx-eb-write-enable = <1>;
+
+				partitions {
+					compatible = "redboot-fis";
+					fis-index-block = <0x3f>;
+				};
+			};
+			gpio1: gpio@1,0 {
+				/* MMIO GPIO at CS1 */
+				compatible = "intel,ixp4xx-expansion-bus-mmio-gpio";
+				gpio-controller;
+				#gpio-cells = <2>;
+				big-endian;
+				reg = <1 0x00000000 0x2>;
+				reg-names = "dat";
+				/* Expansion bus settings */
+				intel,ixp4xx-eb-write-enable = <1>;
+
+				pci-reset-hog {
+					gpio-hog;
+					gpios = <7 GPIO_ACTIVE_HIGH>;
+					output-high;
+					line-name = "PCI reset";
+				};
+				pstn-relay-hog-1 {
+					gpio-hog;
+					gpios = <11 GPIO_ACTIVE_HIGH>;
+					output-low;
+					line-name = "PSTN relay control 1";
+				};
+				pstn-relay-hog-2 {
+					gpio-hog;
+					gpios = <12 GPIO_ACTIVE_HIGH>;
+					output-low;
+					line-name = "PSTN relay control 2";
+				};
+			};
+		};
+
+		pci@c0000000 {
+			status = "okay";
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0xf800 0 0 7>;
+			interrupt-map =
+			/* IDSEL 13 */
+			<0x6800 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 13 is irq 8 */
+			<0x6800 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 13 is irq 6 */
+			/* IDSEL 14 */
+			<0x7000 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 14 is irq 7 */
+			<0x7000 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 14 is irq 8 */
+			/* IDSEL 15 */
+			<0x7800 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 15 is irq 6 */
+			<0x7800 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>; /* INT B on slot 15 is irq 7 */
+		};
+
+		ethb: ethernet@c8009000 {
+			status = "okay";
+			queue-rx = <&qmgr 3>;
+			queue-txready = <&qmgr 20>;
+			phy-mode = "mii";
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				/* 1, 2, 3 and 4 are ports on the KS8995 switch */
+				phy1: ethernet-phy@1 {
+					/* LAN1 */
+					reg = <1>;
+				};
+				phy2: ethernet-phy@2 {
+					/* LAN2 */
+					reg = <2>;
+				};
+				phy3: ethernet-phy@3 {
+					/* LAN3 */
+					reg = <3>;
+				};
+				phy4: ethernet-phy@4 {
+					/* LAN4 */
+					reg = <4>;
+				};
+			};
+		};
+
+		ethc: ethernet@c800a000 {
+			status = "okay";
+			queue-rx = <&qmgr 4>;
+			queue-txready = <&qmgr 21>;
+			phy-mode = "mii";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/intel-ixp42x-adi-coyote.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-adi-coyote.dts
index bd4230d7dac9..765ab36e6f0c 100644
--- a/arch/arm/boot/dts/intel-ixp42x-adi-coyote.dts
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-adi-coyote.dts
@@ -56,7 +56,7 @@
 		};
 
 		pci@c0000000 {
-			status = "ok";
+			status = "okay";
 
 			/*
 			 * Taken from Coyote PCI boardfile.
@@ -80,7 +80,7 @@
 
 		/* EthB */
 		ethernet@c8009000 {
-			status = "ok";
+			status = "okay";
 			queue-rx = <&qmgr 3>;
 			queue-txready = <&qmgr 20>;
 			phy-mode = "rgmii";
@@ -102,7 +102,7 @@
 
 		/* EthC */
 		ethernet@c800a000 {
-			status = "ok";
+			status = "okay";
 			queue-rx = <&qmgr 4>;
 			queue-txready = <&qmgr 21>;
 			phy-mode = "rgmii";
diff --git a/arch/arm/boot/dts/intel-ixp42x-arcom-vulcan.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-arcom-vulcan.dts
index 92b987bc3f99..6f5b4e4eb1cc 100644
--- a/arch/arm/boot/dts/intel-ixp42x-arcom-vulcan.dts
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-arcom-vulcan.dts
@@ -112,7 +112,7 @@
 		};
 
 		pci@c0000000 {
-			status = "ok";
+			status = "okay";
 
 			/*
 			 * Taken from Vulcan PCI boardfile.
@@ -137,7 +137,7 @@
 
 		/* EthB */
 		ethernet@c8009000 {
-			status = "ok";
+			status = "okay";
 			queue-rx = <&qmgr 3>;
 			queue-txready = <&qmgr 20>;
 			phy-mode = "rgmii";
@@ -159,7 +159,7 @@
 
 		/* EthC */
 		ethernet@c800a000 {
-			status = "ok";
+			status = "okay";
 			queue-rx = <&qmgr 4>;
 			queue-txready = <&qmgr 21>;
 			phy-mode = "rgmii";
diff --git a/arch/arm/boot/dts/intel-ixp42x-dlink-dsm-g600.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-dlink-dsm-g600.dts
index 5ab09fb10dae..fa133c913606 100644
--- a/arch/arm/boot/dts/intel-ixp42x-dlink-dsm-g600.dts
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-dlink-dsm-g600.dts
@@ -57,7 +57,7 @@
 
 		button-reset {
 			wakeup-source;
-			linux,code = <KEY_ESC>;
+			linux,code = <KEY_RESTART>;
 			label = "reset";
 			gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
 		};
@@ -122,7 +122,7 @@
 		};
 
 		pci@c0000000 {
-			status = "ok";
+			status = "okay";
 
 			/*
 			 * Taken from DSM-G600 PCI boardfile (dsmg600-pci.c)
diff --git a/arch/arm/boot/dts/intel-ixp42x-freecom-fsg-3.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-freecom-fsg-3.dts
index b740403b05a9..73d3c11dd0d4 100644
--- a/arch/arm/boot/dts/intel-ixp42x-freecom-fsg-3.dts
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-freecom-fsg-3.dts
@@ -44,7 +44,7 @@
 		};
 		button-reset {
 			wakeup-source;
-			linux,code = <KEY_ESC>;
+			linux,code = <KEY_RESTART>;
 			label = "reset";
 			gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
 		};
@@ -159,7 +159,7 @@
 		};
 
 		pci@c0000000 {
-			status = "ok";
+			status = "okay";
 
 			/*
 			 * Written based on the FSG-3 PCI boardfile.
@@ -187,7 +187,7 @@
 
 		/* EthB */
 		ethernet@c8009000 {
-			status = "ok";
+			status = "okay";
 			queue-rx = <&qmgr 3>;
 			queue-txready = <&qmgr 20>;
 			phy-mode = "rgmii";
@@ -209,7 +209,7 @@
 
 		/* EthC */
 		ethernet@c800a000 {
-			status = "ok";
+			status = "okay";
 			queue-rx = <&qmgr 4>;
 			queue-txready = <&qmgr 21>;
 			phy-mode = "rgmii";
diff --git a/arch/arm/boot/dts/intel-ixp42x-gateway-7001.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-gateway-7001.dts
index b7cbc90e1c18..6d5e69035f94 100644
--- a/arch/arm/boot/dts/intel-ixp42x-gateway-7001.dts
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-gateway-7001.dts
@@ -53,13 +53,15 @@
 		};
 
 		pci@c0000000 {
-			status = "ok";
+			status = "okay";
 
 			/*
 			 * Taken from Gateway 7001 PCI boardfile (gateway7001-pci.c)
 			 * We have slots (IDSEL) 1 and 2 with one assigned IRQ
 			 * each handling all IRQs.
 			 */
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0xf800 0 0 7>;
 			interrupt-map =
 			/* IDSEL 1 */
 			<0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */
@@ -74,7 +76,7 @@
 		};
 
 		ethernet@c8009000 {
-			status = "ok";
+			status = "okay";
 			queue-rx = <&qmgr 3>;
 			queue-txready = <&qmgr 20>;
 			phy-mode = "rgmii";
@@ -91,7 +93,7 @@
 		};
 
 		ethernet@c800a000 {
-			status = "ok";
+			status = "okay";
 			queue-rx = <&qmgr 4>;
 			queue-txready = <&qmgr 21>;
 			phy-mode = "rgmii";
diff --git a/arch/arm/boot/dts/intel-ixp42x-gateworks-gw2348.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-gateworks-gw2348.dts
index a5943f51e8c2..97e3f25bb210 100644
--- a/arch/arm/boot/dts/intel-ixp42x-gateworks-gw2348.dts
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-gateworks-gw2348.dts
@@ -108,7 +108,7 @@
 		};
 
 		pci@c0000000 {
-			status = "ok";
+			status = "okay";
 
 			/*
 			 * Taken from Avila PCI boardfile.
@@ -142,7 +142,7 @@
 
 		/* EthB */
 		ethernet@c8009000 {
-			status = "ok";
+			status = "okay";
 			queue-rx = <&qmgr 3>;
 			queue-txready = <&qmgr 20>;
 			phy-mode = "rgmii";
@@ -164,7 +164,7 @@
 
 		/* EthC */
 		ethernet@c800a000 {
-			status = "ok";
+			status = "okay";
 			queue-rx = <&qmgr 4>;
 			queue-txready = <&qmgr 21>;
 			phy-mode = "rgmii";
diff --git a/arch/arm/boot/dts/intel-ixp42x-goramo-multilink.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-goramo-multilink.dts
index f80388b17a9e..5f4c849915db 100644
--- a/arch/arm/boot/dts/intel-ixp42x-goramo-multilink.dts
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-goramo-multilink.dts
@@ -82,13 +82,15 @@
 		};
 
 		pci@c0000000 {
-			status = "ok";
+			status = "okay";
 
 			/*
 			 * The device has 4 slots (IDSEL) with one dedicated IRQ per slot.
 			 * The slots have Ethernet, Ethernet, NEC and MPCI.
 			 * The IDSELs are 11, 12, 13, 14.
 			 */
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0xf800 0 0 7>;
 			interrupt-map =
 			/* IDSEL 11 - Ethernet A */
 			<0x5800 0 0 1 &gpio0 4 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 11 is irq 4 */
@@ -148,7 +150,7 @@
 
 		/* EthB */
 		ethernet@c8009000 {
-			status = "ok";
+			status = "okay";
 			queue-rx = <&qmgr 3>;
 			queue-txready = <&qmgr 32>;
 			phy-mode = "rgmii";
@@ -170,7 +172,7 @@
 
 		/* EthC */
 		ethernet@c800a000 {
-			status = "ok";
+			status = "okay";
 			queue-rx = <&qmgr 4>;
 			queue-txready = <&qmgr 33>;
 			phy-mode = "rgmii";
diff --git a/arch/arm/boot/dts/intel-ixp42x-iomega-nas100d.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-iomega-nas100d.dts
index cbc87b344f6a..26f02dad6a54 100644
--- a/arch/arm/boot/dts/intel-ixp42x-iomega-nas100d.dts
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-iomega-nas100d.dts
@@ -63,7 +63,7 @@
 		};
 		button-reset {
 			wakeup-source;
-			linux,code = <KEY_ESC>;
+			linux,code = <KEY_RESTART>;
 			label = "reset";
 			gpios = <&gpio0 4 GPIO_ACTIVE_LOW>;
 		};
@@ -109,7 +109,7 @@
 		};
 
 		pci@c0000000 {
-			status = "ok";
+			status = "okay";
 
 			/*
 			 * Taken from NAS 100D PCI boardfile (nas100d-pci.c)
@@ -129,7 +129,7 @@
 		};
 
 		ethernet@c8009000 {
-			status = "ok";
+			status = "okay";
 			queue-rx = <&qmgr 3>;
 			queue-txready = <&qmgr 20>;
 			phy-mode = "rgmii";
diff --git a/arch/arm/boot/dts/intel-ixp42x-ixdp425.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-ixdp425.dts
index beaadda4685f..194945748dc3 100644
--- a/arch/arm/boot/dts/intel-ixp42x-ixdp425.dts
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-ixdp425.dts
@@ -40,7 +40,7 @@
 
 		/* EthB */
 		ethernet@c8009000 {
-			status = "ok";
+			status = "okay";
 			queue-rx = <&qmgr 3>;
 			queue-txready = <&qmgr 20>;
 			phy-mode = "rgmii";
@@ -62,7 +62,7 @@
 
 		/* EthC */
 		ethernet@c800a000 {
-			status = "ok";
+			status = "okay";
 			queue-rx = <&qmgr 4>;
 			queue-txready = <&qmgr 21>;
 			phy-mode = "rgmii";
diff --git a/arch/arm/boot/dts/intel-ixp42x-ixdpg425.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-ixdpg425.dts
index f17cab12a64b..7011fea6205b 100644
--- a/arch/arm/boot/dts/intel-ixp42x-ixdpg425.dts
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-ixdpg425.dts
@@ -61,7 +61,7 @@
 		};
 
 		pci@c0000000 {
-			status = "ok";
+			status = "okay";
 
 			/*
 			 * Taken from IXDPG425 PCI boardfile.
@@ -95,7 +95,7 @@
 
 		/* EthB */
 		ethernet@c8009000 {
-			status = "ok";
+			status = "okay";
 			queue-rx = <&qmgr 3>;
 			queue-txready = <&qmgr 20>;
 			phy-mode = "rgmii";
@@ -117,7 +117,7 @@
 
 		/* EthC */
 		ethernet@c800a000 {
-			status = "ok";
+			status = "okay";
 			queue-rx = <&qmgr 4>;
 			queue-txready = <&qmgr 21>;
 			phy-mode = "rgmii";
diff --git a/arch/arm/boot/dts/intel-ixp42x-linksys-nslu2.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-linksys-nslu2.dts
index 0edc5928e00b..2f7c34c649ea 100644
--- a/arch/arm/boot/dts/intel-ixp42x-linksys-nslu2.dts
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-linksys-nslu2.dts
@@ -65,7 +65,7 @@
 		};
 		button-reset {
 			wakeup-source;
-			linux,code = <KEY_ESC>;
+			linux,code = <KEY_RESTART>;
 			label = "reset";
 			gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
 		};
@@ -90,17 +90,26 @@
 		timeout-ms = <5000>;
 	};
 
-	gpio-beeper {
-		compatible = "gpio-beeper";
+	gpio_pwm: pwm {
+		#pwm-cells = <3>;
+		compatible = "pwm-gpio";
 		gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
 	};
 
+	beeper {
+		compatible = "pwm-beeper";
+		pwms = <&gpio_pwm 0 1 0>;
+		beeper-hz = <1000>;
+	};
+
 	soc {
 		bus@c4000000 {
 			/* The first 16MB region at CS0 on the expansion bus */
 			flash@0,0 {
 				compatible = "intel,ixp4xx-flash", "cfi-flash";
 				bank-width = <2>;
+				/* Enable writes on the expansion bus */
+				intel,ixp4xx-eb-write-enable = <1>;
 				/*
 				 * 8 MB of Flash in 0x20000 byte blocks
 				 * mapped in at CS0.
@@ -116,7 +125,7 @@
 		};
 
 		pci@c0000000 {
-			status = "ok";
+			status = "okay";
 
 			/*
 			 * Taken from NSLU2 PCI boardfile, INT A, B, C swizzled D constant
@@ -143,7 +152,7 @@
 		};
 
 		ethernet@c8009000 {
-			status = "ok";
+			status = "okay";
 			queue-rx = <&qmgr 3>;
 			queue-txready = <&qmgr 20>;
 			phy-mode = "rgmii";
diff --git a/arch/arm/boot/dts/intel-ixp42x-linksys-wrv54g.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-linksys-wrv54g.dts
index 5e7e31b74b04..cb1842c83ac8 100644
--- a/arch/arm/boot/dts/intel-ixp42x-linksys-wrv54g.dts
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-linksys-wrv54g.dts
@@ -13,7 +13,7 @@
 
 / {
 	model = "Linksys WRV54G / Gemtek GTWX5715";
-	compatible = "linksys,wrv54g", "gemtek,gtwx5715", "intel,ixp42x";
+	compatible = "linksys,wrv54g", "intel,ixp42x";
 	#address-cells = <1>;
 	#size-cells = <1>;
 
@@ -72,10 +72,55 @@
 		cs-gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
 		num-chipselects = <1>;
 
-		switch@0 {
+		ethernet-switch@0 {
 			compatible = "micrel,ks8995";
 			reg = <0>;
 			spi-max-frequency = <50000000>;
+
+			/*
+			 * The PHYs are accessed over the external MDIO
+			 * bus and not internally through the switch control
+			 * registers.
+			 */
+			ethernet-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ethernet-port@0 {
+					reg = <0>;
+					label = "1";
+					phy-mode = "mii";
+					phy-handle = <&phy1>;
+				};
+				ethernet-port@1 {
+					reg = <1>;
+					label = "2";
+					phy-mode = "mii";
+					phy-handle = <&phy2>;
+				};
+				ethernet-port@2 {
+					reg = <2>;
+					label = "3";
+					phy-mode = "mii";
+					phy-handle = <&phy3>;
+				};
+				ethernet-port@3 {
+					reg = <3>;
+					label = "4";
+					phy-mode = "mii";
+					phy-handle = <&phy4>;
+				};
+				ethernet-port@4 {
+					reg = <4>;
+					ethernet = <&ethb>;
+					phy-mode = "mii";
+					fixed-link {
+						speed = <100>;
+						full-duplex;
+					};
+				};
+
+			};
 		};
 	};
 
@@ -117,7 +162,7 @@
 		};
 
 		pci@c0000000 {
-			status = "ok";
+			status = "okay";
 
 			/*
 			 * We have up to 2 slots (IDSEL) with 2 swizzled IRQs.
@@ -135,40 +180,59 @@
 		};
 
 		/*
-		 * EthB - connected to the KS8995 switch ports 1-4
-		 * FIXME: the boardfile defines .phy_mask = 0x1e for this port to enable output to
-		 * all four switch ports, also using an out of tree multiphy patch.
-		 * Do we need a new binding and property for this?
+		 * EthB connects to the KS8995 CPU port and faces ports 1-4
+		 * through the switch fabric.
+		 *
+		 * To complicate things, the MDIO channel is also only
+		 * accessible through EthB, but used independently for PHY
+		 * control.
 		 */
-		ethernet@c8009000 {
-			status = "ok";
+		ethb: ethernet@c8009000 {
+			status = "okay";
 			queue-rx = <&qmgr 3>;
 			queue-txready = <&qmgr 20>;
-			phy-mode = "rgmii";
-			phy-handle = <&phy4>;
+			phy-mode = "mii";
+			fixed-link {
+				speed = <100>;
+				full-duplex;
+			};
 
 			mdio {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				/* Should be ports 1-4 on the KS8995 switch */
+				/*
+				 * LAN ports 1-4 on the KS8995 switch
+				 * and PHY5 for WAN need to be accessed
+				 * through this external MDIO channel.
+				 */
+				phy1: ethernet-phy@1 {
+					reg = <1>;
+				};
+				phy2: ethernet-phy@2 {
+					reg = <2>;
+				};
+				phy3: ethernet-phy@3 {
+					reg = <3>;
+				};
 				phy4: ethernet-phy@4 {
 					reg = <4>;
 				};
-
-				/* Should be port 5 on the KS8995 switch */
 				phy5: ethernet-phy@5 {
 					reg = <5>;
 				};
 			};
 		};
 
-		/* EthC - connected to KS8995 switch port 5 */
-		ethernet@c800a000 {
-			status = "ok";
+		/*
+		 * EthC connects to MII-P5 on the KS8995 bypassing
+		 * all of the switch logic and facing PHY5
+		 */
+		ethc: ethernet@c800a000 {
+			status = "okay";
 			queue-rx = <&qmgr 4>;
 			queue-txready = <&qmgr 21>;
-			phy-mode = "rgmii";
+			phy-mode = "mii";
 			phy-handle = <&phy5>;
 		};
 	};
diff --git a/arch/arm/boot/dts/intel-ixp42x-netgear-wg302v1.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-netgear-wg302v1.dts
index df2ca6d95ee5..a351a97d257e 100644
--- a/arch/arm/boot/dts/intel-ixp42x-netgear-wg302v1.dts
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-netgear-wg302v1.dts
@@ -8,6 +8,7 @@
 
 #include "intel-ixp42x.dtsi"
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
 
 / {
 	model = "Netgear WG302 v1";
@@ -32,6 +33,35 @@
 		serial0 = &uart1;
 	};
 
+	leds {
+		compatible = "gpio-leds";
+		test_led: led-test {
+			color = <LED_COLOR_ID_AMBER>;
+			function = "test";
+			gpios = <&gpio0 4 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+		wlan_led: led-wlan {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_WLAN;
+			gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+			linux,default-trigger = "phy0tx";
+		};
+	};
+
+	gpio_keys {
+		/* RESET is on GPIO13 which can't fire interrupts */
+		compatible = "gpio-keys-polled";
+		poll-interval = <100>;
+
+		button-reset {
+			linux,code = <KEY_RESTART>;
+			label = "reset";
+			gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+		};
+	};
+
 	soc {
 		bus@c4000000 {
 			flash@0,0 {
@@ -54,10 +84,10 @@
 		};
 
 		pci@c0000000 {
-			status = "ok";
+			status = "okay";
 
 			/*
-			 * Taken from WG302 v2 PCI boardfile (wg302v2-pci.c)
+			 * Taken from WG302 v1 PCI boardfile (wg302v1-pci.c)
 			 * We have slots (IDSEL) 1 and 2 with one assigned IRQ
 			 * each handling all IRQs.
 			 */
@@ -70,14 +100,14 @@
 			<0x0800 0 0 3 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 8 */
 			<0x0800 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */
 			/* IDSEL 2 */
-			<0x1000 0 0 1 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 9 */
-			<0x1000 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */
-			<0x1000 0 0 3 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 9 */
-			<0x1000 0 0 4 &gpio0 9 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 2 is irq 9 */
+			<0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */
+			<0x1000 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 10 */
+			<0x1000 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 10 */
+			<0x1000 0 0 4 &gpio0 10 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 2 is irq 10 */
 		};
 
 		ethernet@c8009000 {
-			status = "ok";
+			status = "okay";
 			queue-rx = <&qmgr 3>;
 			queue-txready = <&qmgr 20>;
 			phy-mode = "rgmii";
diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-usrobotics-usr8200.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-usrobotics-usr8200.dts
new file mode 100644
index 000000000000..2c89db34c8d8
--- /dev/null
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-usrobotics-usr8200.dts
@@ -0,0 +1,251 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for the USRobotics USR8200 firewall
+ * VPN and NAS. Based on know-how from Peter Denison.
+ *
+ * This machine is based on IXP422, the USR internal codename
+ * is "Jeeves".
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "USRobotics USR8200";
+	compatible = "usr,usr8200", "intel,ixp42x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x4000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		stdout-path = "uart1:115200n8";
+	};
+
+	aliases {
+		/* These are switched around */
+		serial0 = &uart1;
+		serial1 = &uart0;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		ieee1394_led: led-1394 {
+			label = "usr8200:green:1394";
+			gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+		usb1_led: led-usb1 {
+			label = "usr8200:green:usb1";
+			gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+		usb2_led: led-usb2 {
+			label = "usr8200:green:usb2";
+			gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+		wireless_led: led-wireless {
+			/*
+			 * This LED is mounted inside the case but cannot be
+			 * seen from the outside: probably USR planned at one
+			 * point for the device to have a wireless card, then
+			 * changed their mind and didn't mount it, leaving the
+			 * LED in place.
+			 */
+			label = "usr8200:green:wireless";
+			gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+		pwr_led: led-pwr {
+			label = "usr8200:green:pwr";
+			gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		button-reset {
+			wakeup-source;
+			linux,code = <KEY_RESTART>;
+			label = "reset";
+			gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	soc {
+		bus@c4000000 {
+			flash@0,0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/* Enable writes on the expansion bus */
+				intel,ixp4xx-eb-write-enable = <1>;
+				/* 16 MB of Flash mapped in at CS0 */
+				reg = <0 0x00000000 0x1000000>;
+
+				partitions {
+					compatible = "redboot-fis";
+					/* Eraseblock at 0x0fe0000 */
+					fis-index-block = <0x7f>;
+				};
+			};
+			rtc@2,0 {
+				/* EPSON RTC7301 DG DIL-capsule */
+				compatible = "epson,rtc7301dg";
+				/*
+				 * These timing settings were found in the boardfile patch:
+				 * IXP4XX_EXP_CS2 = 0x3fff000 | IXP4XX_EXP_BUS_SIZE(0) | IXP4XX_EXP_BUS_WR_EN |
+				 *                  IXP4XX_EXP_BUS_CS_EN | IXP4XX_EXP_BUS_BYTE_EN;
+				 */
+				intel,ixp4xx-eb-t1 = <0>; // no cycles extra address phase
+				intel,ixp4xx-eb-t2 = <0>; // no cycles extra setup phase
+				intel,ixp4xx-eb-t3 = <15>; // 15 cycles extra strobe phase
+				intel,ixp4xx-eb-t4 = <3>; // 3 cycles extra hold phase
+				intel,ixp4xx-eb-t5 = <15>; // 15 cycles extra recovery phase
+				intel,ixp4xx-eb-cycle-type = <0>; // Intel cycle
+				intel,ixp4xx-eb-byte-access-on-halfword = <0>;
+				intel,ixp4xx-eb-mux-address-and-data = <0>;
+				intel,ixp4xx-eb-ahb-split-transfers = <0>;
+				intel,ixp4xx-eb-write-enable = <1>;
+				intel,ixp4xx-eb-byte-access = <1>;
+				/* 512 bytes at CS2 */
+				reg = <2 0x00000000 0x0000200>;
+				reg-io-width = <1>;
+				native-endian;
+				/* FIXME: try to check if there is an IRQ for the RTC? */
+			};
+		};
+
+		pci@c0000000 {
+			status = "okay";
+
+			/*
+			 * Taken from USR8200 boardfile from OpenWrt
+			 *
+			 * We have 3 slots (IDSEL) with partly swizzled IRQs on slot 16.
+			 * We assume the same IRQ for all pins on the remaining slots, that
+			 * is what the boardfile was doing.
+			 */
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0xf800 0 0 7>;
+			interrupt-map =
+			/* IDSEL 14 used for "Wireless" in the board file */
+			<0x7000 0 0 1 &gpio0 7  IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 14 is irq 7 */
+			/* IDSEL 15 used for VIA VT6307 IEEE 1394 Firewire */
+			<0x7800 0 0 1 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 15 is irq 8 */
+			/* IDSEL 16 used for VIA VT6202 USB 2.0 4+1 */
+			<0x8000 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 16 is irq 11 */
+			<0x8000 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 16 is irq 10 */
+			<0x8000 0 0 3 &gpio0 9  IRQ_TYPE_LEVEL_LOW>; /* INT C on slot 16 is irq 9 */
+		};
+
+		gpio@c8004000 {
+			/* Enable clock out on GPIO 15 */
+			intel,ixp4xx-gpio15-clkout;
+		};
+
+		/* EthB WAN */
+		ethernet@c8009000 {
+			status = "okay";
+			queue-rx = <&qmgr 3>;
+			queue-txready = <&qmgr 20>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy9>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				/*
+				 * PHY 0..4 are internal to the MV88E6060 switch but appear
+				 * as independent devices.
+				 */
+				phy0: ethernet-phy@0 {
+					reg = <0>;
+				};
+				phy1: ethernet-phy@1 {
+					reg = <1>;
+				};
+				phy2: ethernet-phy@2 {
+					reg = <2>;
+				};
+				phy3: ethernet-phy@3 {
+					reg = <3>;
+				};
+
+				/* Altima AMI101L used by the WAN port */
+				phy9: ethernet-phy@9 {
+					reg = <9>;
+				};
+
+				/* The switch uses MDIO addresses 16 thru 31 */
+				switch@16 {
+					compatible = "marvell,mv88e6060";
+					reg = <16>;
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+							label = "lan1";
+							phy-handle = <&phy0>;
+						};
+
+						port@1 {
+							reg = <1>;
+							label = "lan2";
+							phy-handle = <&phy1>;
+						};
+
+						port@2 {
+							reg = <2>;
+							label = "lan3";
+							phy-handle = <&phy2>;
+						};
+
+						port@3 {
+							reg = <3>;
+							label = "lan4";
+							phy-handle = <&phy3>;
+						};
+
+						port@5 {
+							/* Port 5 is the CPU port according to the MV88E6060 datasheet */
+							reg = <5>;
+							phy-mode = "rgmii-id";
+							ethernet = <&ethc>;
+							label = "cpu";
+							fixed-link {
+								speed = <100>;
+								full-duplex;
+							};
+						};
+					};
+				};
+			};
+		};
+
+		/* EthC LAN connected to the Marvell DSA Switch */
+		ethc: ethernet@c800a000 {
+			status = "okay";
+			queue-rx = <&qmgr 4>;
+			queue-txready = <&qmgr 21>;
+			phy-mode = "rgmii";
+			fixed-link {
+				speed = <100>;
+				full-duplex;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/intel-ixp42x-welltech-epbx100.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-welltech-epbx100.dts
index f5846a50e4d4..c550c421b659 100644
--- a/arch/arm/boot/dts/intel-ixp42x-welltech-epbx100.dts
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-welltech-epbx100.dts
@@ -76,5 +76,23 @@
 				};
 			};
 		};
+
+		/* LAN port */
+		ethernet@c8009000 {
+			status = "okay";
+			queue-rx = <&qmgr 3>;
+			queue-txready = <&qmgr 20>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy5>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy5: ethernet-phy@5 {
+					reg = <5>;
+				};
+			};
+		};
 	};
 };
diff --git a/arch/arm/boot/dts/intel-ixp42x.dtsi b/arch/arm/boot/dts/intel/ixp/intel-ixp42x.dtsi
index 84cee8ec3ab8..84cee8ec3ab8 100644
--- a/arch/arm/boot/dts/intel-ixp42x.dtsi
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x.dtsi
diff --git a/arch/arm/boot/dts/intel-ixp43x-gateworks-gw2358.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp43x-gateworks-gw2358.dts
index cf4010d60187..1db849515f9e 100644
--- a/arch/arm/boot/dts/intel-ixp43x-gateworks-gw2358.dts
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp43x-gateworks-gw2358.dts
@@ -121,7 +121,7 @@
 		};
 
 		pci@c0000000 {
-			status = "ok";
+			status = "okay";
 
 			/*
 			 * In the boardfile for the Cambria from OpenWRT the interrupts
@@ -167,7 +167,7 @@
 		};
 
 		ethernet@c800a000 {
-			status = "ok";
+			status = "okay";
 			queue-rx = <&qmgr 4>;
 			queue-txready = <&qmgr 21>;
 			phy-mode = "rgmii";
@@ -188,7 +188,7 @@
 		};
 
 		ethernet@c800c000 {
-			status = "ok";
+			status = "okay";
 			queue-rx = <&qmgr 2>;
 			queue-txready = <&qmgr 19>;
 			phy-mode = "rgmii";
diff --git a/arch/arm/boot/dts/intel-ixp43x-kixrp435.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp43x-kixrp435.dts
index 3d7cfa1a5ed4..4703a8b24765 100644
--- a/arch/arm/boot/dts/intel-ixp43x-kixrp435.dts
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp43x-kixrp435.dts
@@ -36,7 +36,7 @@
 
 		/* CHECKME: ethernet set-up taken from Gateworks Cambria */
 		ethernet@c800a000 {
-			status = "ok";
+			status = "okay";
 			queue-rx = <&qmgr 4>;
 			queue-txready = <&qmgr 21>;
 			phy-mode = "rgmii";
@@ -57,7 +57,7 @@
 		};
 
 		ethernet@c800c000 {
-			status = "ok";
+			status = "okay";
 			queue-rx = <&qmgr 2>;
 			queue-txready = <&qmgr 19>;
 			phy-mode = "rgmii";
diff --git a/arch/arm/boot/dts/intel-ixp43x.dtsi b/arch/arm/boot/dts/intel/ixp/intel-ixp43x.dtsi
index 60bf9903e0f8..60bf9903e0f8 100644
--- a/arch/arm/boot/dts/intel-ixp43x.dtsi
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp43x.dtsi
diff --git a/arch/arm/boot/dts/intel-ixp45x-ixp46x.dtsi b/arch/arm/boot/dts/intel/ixp/intel-ixp45x-ixp46x.dtsi
index 1dd4a65cb7a6..1dd4a65cb7a6 100644
--- a/arch/arm/boot/dts/intel-ixp45x-ixp46x.dtsi
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp45x-ixp46x.dtsi
diff --git a/arch/arm/boot/dts/intel-ixp46x-ixdp465.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp46x-ixdp465.dts
index a062cd1a6588..a062cd1a6588 100644
--- a/arch/arm/boot/dts/intel-ixp46x-ixdp465.dts
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp46x-ixdp465.dts
diff --git a/arch/arm/boot/dts/intel-ixp4xx-reference-design.dtsi b/arch/arm/boot/dts/intel/ixp/intel-ixp4xx-reference-design.dtsi
index 146352ba848b..31c0a69771c4 100644
--- a/arch/arm/boot/dts/intel-ixp4xx-reference-design.dtsi
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp4xx-reference-design.dtsi
@@ -99,7 +99,7 @@
 		};
 
 		pci@c0000000 {
-			status = "ok";
+			status = "okay";
 
 			/*
 			 * Taken from IXDP425 PCI boardfile.
diff --git a/arch/arm/boot/dts/intel-ixp4xx.dtsi b/arch/arm/boot/dts/intel/ixp/intel-ixp4xx.dtsi
index 51a716c59669..0adeccabd4fe 100644
--- a/arch/arm/boot/dts/intel-ixp4xx.dtsi
+++ b/arch/arm/boot/dts/intel/ixp/intel-ixp4xx.dtsi
@@ -193,10 +193,10 @@
 			compatible = "intel,ixp4xx-ethernet";
 			reg = <0xc800c000 0x1000>;
 			status = "disabled";
-			intel,npe = <0>;
 			/* Dummy values that depend on firmware */
 			queue-rx = <&qmgr 0>;
 			queue-txready = <&qmgr 0>;
+			intel,npe-handle = <&npe 0>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/intel/pxa/Makefile b/arch/arm/boot/dts/intel/pxa/Makefile
new file mode 100644
index 000000000000..24d5240f08e7
--- /dev/null
+++ b/arch/arm/boot/dts/intel/pxa/Makefile
@@ -0,0 +1,8 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_PXA) += \
+	pxa300-raumfeld-connector.dtb \
+	pxa300-raumfeld-controller.dtb \
+	pxa300-raumfeld-speaker-l.dtb \
+	pxa300-raumfeld-speaker-m.dtb \
+	pxa300-raumfeld-speaker-one.dtb \
+	pxa300-raumfeld-speaker-s.dtb
diff --git a/arch/arm/boot/dts/pxa25x.dtsi b/arch/arm/boot/dts/intel/pxa/pxa25x.dtsi
index a248bf038033..5f8300e356ad 100644
--- a/arch/arm/boot/dts/pxa25x.dtsi
+++ b/arch/arm/boot/dts/intel/pxa/pxa25x.dtsi
@@ -38,9 +38,12 @@
 			compatible = "marvell,pdma-1.0";
 			reg = <0x40000000 0x10000>;
 			interrupts = <25>;
-			#dma-channels = <16>;
 			#dma-cells = <2>;
+			/* For backwards compatibility: */
+			#dma-channels = <16>;
+			dma-channels = <16>;
 			#dma-requests = <40>;
+			dma-requests = <40>;
 			status = "okay";
 		};
 
diff --git a/arch/arm/boot/dts/pxa27x.dtsi b/arch/arm/boot/dts/intel/pxa/pxa27x.dtsi
index ccbecad9c5c7..a2cbfb3be609 100644
--- a/arch/arm/boot/dts/pxa27x.dtsi
+++ b/arch/arm/boot/dts/intel/pxa/pxa27x.dtsi
@@ -12,9 +12,12 @@
 			compatible = "marvell,pdma-1.0";
 			reg = <0x40000000 0x10000>;
 			interrupts = <25>;
-			#dma-channels = <32>;
 			#dma-cells = <2>;
+			/* For backwards compatibility: */
+			#dma-channels = <32>;
+			dma-channels = <32>;
 			#dma-requests = <75>;
+			dma-requests = <75>;
 			status = "okay";
 		};
 
diff --git a/arch/arm/boot/dts/pxa2xx.dtsi b/arch/arm/boot/dts/intel/pxa/pxa2xx.dtsi
index 84154c43fe65..84154c43fe65 100644
--- a/arch/arm/boot/dts/pxa2xx.dtsi
+++ b/arch/arm/boot/dts/intel/pxa/pxa2xx.dtsi
diff --git a/arch/arm/boot/dts/pxa300-raumfeld-common.dtsi b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-common.dtsi
index 8a6721d436bd..147c99191dc2 100644
--- a/arch/arm/boot/dts/pxa300-raumfeld-common.dtsi
+++ b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-common.dtsi
@@ -189,31 +189,31 @@
 
 		regulators {
 			regulator-v3 {
-				regulator-compatible= "V3(DCDC)";
+				regulator-compatible = "V3(DCDC)";
 				regulator-min-microvolt = <725000>;
 				regulator-max-microvolt = <1800000>;
 			};
 
 			regulator-v4 {
-				regulator-compatible= "V4(DCDC)";
+				regulator-compatible = "V4(DCDC)";
 				regulator-min-microvolt = <725000>;
 				regulator-max-microvolt = <1800000>;
 			};
 
 			regulator-v5 {
-				regulator-compatible= "V5(LDO)";
+				regulator-compatible = "V5(LDO)";
 				regulator-min-microvolt = <1700000>;
 				regulator-max-microvolt = <2000000>;
 			};
 
 			reg_vcc_sdio: regulator-v6 {
-				regulator-compatible= "V6(LDO)";
+				regulator-compatible = "V6(LDO)";
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			regulator-v7 {
-				regulator-compatible= "V7(LDO)";
+				regulator-compatible = "V7(LDO)";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3300000>;
 			};
diff --git a/arch/arm/boot/dts/pxa300-raumfeld-connector.dts b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-connector.dts
index 3e9445419e39..3e9445419e39 100644
--- a/arch/arm/boot/dts/pxa300-raumfeld-connector.dts
+++ b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-connector.dts
diff --git a/arch/arm/boot/dts/pxa300-raumfeld-controller.dts b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-controller.dts
index 12b15945ac6d..12b15945ac6d 100644
--- a/arch/arm/boot/dts/pxa300-raumfeld-controller.dts
+++ b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-controller.dts
diff --git a/arch/arm/boot/dts/pxa300-raumfeld-speaker-l.dts b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-l.dts
index 5a0f7f17856f..5a0f7f17856f 100644
--- a/arch/arm/boot/dts/pxa300-raumfeld-speaker-l.dts
+++ b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-l.dts
diff --git a/arch/arm/boot/dts/pxa300-raumfeld-speaker-m.dts b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-m.dts
index fa10d896282c..fa10d896282c 100644
--- a/arch/arm/boot/dts/pxa300-raumfeld-speaker-m.dts
+++ b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-m.dts
diff --git a/arch/arm/boot/dts/pxa300-raumfeld-speaker-one.dts b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-one.dts
index a70560a8ea92..a70560a8ea92 100644
--- a/arch/arm/boot/dts/pxa300-raumfeld-speaker-one.dts
+++ b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-one.dts
diff --git a/arch/arm/boot/dts/pxa300-raumfeld-speaker-s.dts b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-s.dts
index 36e20cbf8704..36e20cbf8704 100644
--- a/arch/arm/boot/dts/pxa300-raumfeld-speaker-s.dts
+++ b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-s.dts
diff --git a/arch/arm/boot/dts/pxa300-raumfeld-tuneable-clock.dtsi b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-tuneable-clock.dtsi
index 561483b93989..561483b93989 100644
--- a/arch/arm/boot/dts/pxa300-raumfeld-tuneable-clock.dtsi
+++ b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-tuneable-clock.dtsi
diff --git a/arch/arm/boot/dts/pxa3xx.dtsi b/arch/arm/boot/dts/intel/pxa/pxa3xx.dtsi
index d19674812cd2..f9c216f91865 100644
--- a/arch/arm/boot/dts/pxa3xx.dtsi
+++ b/arch/arm/boot/dts/intel/pxa/pxa3xx.dtsi
@@ -122,9 +122,12 @@
 			compatible = "marvell,pdma-1.0";
 			reg = <0x40000000 0x10000>;
 			interrupts = <25>;
-			#dma-channels = <32>;
 			#dma-cells = <2>;
+			/* For backwards compatibility: */
+			#dma-channels = <32>;
+			dma-channels = <32>;
 			#dma-requests = <100>;
+			dma-requests = <100>;
 			status = "okay";
 		};
 
diff --git a/arch/arm/boot/dts/intel/socfpga/Makefile b/arch/arm/boot/dts/intel/socfpga/Makefile
new file mode 100644
index 000000000000..7f69a0355ea5
--- /dev/null
+++ b/arch/arm/boot/dts/intel/socfpga/Makefile
@@ -0,0 +1,18 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_INTEL_SOCFPGA) += \
+	socfpga_arria5_socdk.dtb \
+	socfpga_arria10_chameleonv3.dtb \
+	socfpga_arria10_mercury_pe1.dtb \
+	socfpga_arria10_socdk_nand.dtb \
+	socfpga_arria10_socdk_qspi.dtb \
+	socfpga_arria10_socdk_sdmmc.dtb \
+	socfpga_cyclone5_chameleon96.dtb \
+	socfpga_cyclone5_mcvevk.dtb \
+	socfpga_cyclone5_socdk.dtb \
+	socfpga_cyclone5_de0_nano_soc.dtb \
+	socfpga_cyclone5_de10nano.dtb \
+	socfpga_cyclone5_sockit.dtb \
+	socfpga_cyclone5_socrates.dtb \
+	socfpga_cyclone5_sodia.dtb \
+	socfpga_cyclone5_vining_fpga.dtb \
+	socfpga_vt.dtb
diff --git a/arch/arm/boot/dts/socfpga.dtsi b/arch/arm/boot/dts/intel/socfpga/socfpga.dtsi
index 7c1d6423d7f8..35be14150f41 100644
--- a/arch/arm/boot/dts/socfpga.dtsi
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga.dtsi
@@ -46,7 +46,7 @@
 		      <0xff113000 0x1000>;
 	};
 
-	intc: intc@fffed000 {
+	intc: interrupt-controller@fffed000 {
 		compatible = "arm,cortex-a9-gic";
 		#interrupt-cells = <3>;
 		interrupt-controller;
@@ -80,8 +80,6 @@
 					     <0 110 4>,
 					     <0 111 4>;
 				#dma-cells = <1>;
-				#dma-channels = <8>;
-				#dma-requests = <32>;
 				clocks = <&l4_main_clk>;
 				clock-names = "apb_pclk";
 				resets = <&rst DMA_RESET>;
@@ -455,7 +453,6 @@
 						compatible = "altr,socfpga-gate-clk";
 						clocks = <&f2s_periph_ref_clk>, <&main_nand_sdmmc_clk>, <&per_nand_mmc_clk>;
 						clk-gate = <0xa0 8>;
-						clk-phase = <0 135>;
 					};
 
 					sdmmc_clk_divided: sdmmc_clk_divided {
@@ -563,6 +560,12 @@
 			interrupts = <0 175 4>;
 		};
 
+		socfpga_axi_setup: stmmac-axi-config {
+			snps,wr_osr_lmt = <0xf>;
+			snps,rd_osr_lmt = <0xf>;
+			snps,blen = <0 0 0 0 16 0 0>;
+		};
+
 		gmac0: ethernet@ff700000 {
 			compatible = "altr,socfpga-stmmac", "snps,dwmac-3.70a", "snps,dwmac";
 			altr,sysmgr-syscon = <&sysmgr 0x60 0>;
@@ -578,6 +581,7 @@
 			snps,perfect-filter-entries = <128>;
 			tx-fifo-depth = <4096>;
 			rx-fifo-depth = <4096>;
+			snps,axi-config = <&socfpga_axi_setup>;
 			status = "disabled";
 		};
 
@@ -596,6 +600,7 @@
 			snps,perfect-filter-entries = <128>;
 			tx-fifo-depth = <4096>;
 			rx-fifo-depth = <4096>;
+			snps,axi-config = <&socfpga_axi_setup>;
 			status = "disabled";
 		};
 
@@ -744,12 +749,12 @@
 			arm,prefetch-offset = <7>;
 		};
 
-		l3regs@0xff800000 {
+		l3regs@ff800000 {
 			compatible = "altr,l3regs", "syscon";
 			reg = <0xff800000 0x1000>;
 		};
 
-		mmc: dwmmc0@ff704000 {
+		mmc: mmc@ff704000 {
 			compatible = "altr,socfpga-dw-mshc";
 			reg = <0xff704000 0x1000>;
 			interrupts = <0 139 4>;
@@ -759,10 +764,11 @@
 			clocks = <&l4_mp_clk>, <&sdmmc_clk_divided>;
 			clock-names = "biu", "ciu";
 			resets = <&rst SDMMC_RESET>;
+			altr,sysmgr-syscon = <&sysmgr 0x108 3>;
 			status = "disabled";
 		};
 
-		nand0: nand@ff900000 {
+		nand0: nand-controller@ff900000 {
 			#address-cells = <0x1>;
 			#size-cells = <0x0>;
 			compatible = "altr,socfpga-denali-nand";
@@ -899,7 +905,7 @@
 			reset-names = "timer";
 		};
 
-		uart0: serial0@ffc02000 {
+		uart0: serial@ffc02000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0xffc02000 0x1000>;
 			interrupts = <0 162 4>;
@@ -912,7 +918,7 @@
 			resets = <&rst UART0_RESET>;
 		};
 
-		uart1: serial1@ffc03000 {
+		uart1: serial@ffc03000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0xffc03000 0x1000>;
 			interrupts = <0 163 4>;
diff --git a/arch/arm/boot/dts/socfpga_arria10.dtsi b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10.dtsi
index 3ba431dfa8c9..b108265e9bde 100644
--- a/arch/arm/boot/dts/socfpga_arria10.dtsi
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10.dtsi
@@ -38,7 +38,7 @@
 		      <0xff113000 0x1000>;
 	};
 
-	intc: intc@ffffd000 {
+	intc: interrupt-controller@ffffd000 {
 		compatible = "arm,cortex-a9-gic";
 		#interrupt-cells = <3>;
 		interrupt-controller;
@@ -73,8 +73,6 @@
 					     <0 90 IRQ_TYPE_LEVEL_HIGH>,
 					     <0 91 IRQ_TYPE_LEVEL_HIGH>;
 				#dma-cells = <1>;
-				#dma-channels = <8>;
-				#dma-requests = <32>;
 				clocks = <&l4_main_clk>;
 				clock-names = "apb_pclk";
 				resets = <&rst DMA_RESET>, <&rst DMA_OCP_RESET>;
@@ -367,7 +365,6 @@
 						compatible = "altr,socfpga-a10-gate-clk";
 						clocks = <&sdmmc_free_clk>;
 						clk-gate = <0xC8 5>;
-						clk-phase = <0 135>;
 					};
 
 					qspi_clk: qspi_clk {
@@ -658,7 +655,7 @@
 			arm,shared-override;
 		};
 
-		mmc: dwmmc0@ff808000 {
+		mmc: mmc@ff808000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "altr,socfpga-dw-mshc";
@@ -668,10 +665,11 @@
 			clocks = <&l4_mp_clk>, <&sdmmc_clk>;
 			clock-names = "biu", "ciu";
 			resets = <&rst SDMMC_RESET>;
+			altr,sysmgr-syscon = <&sysmgr 0x28 4>;
 			status = "disabled";
 		};
 
-		nand: nand@ffb90000 {
+		nand: nand-controller@ffb90000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "altr,socfpga-denali-nand";
@@ -738,6 +736,16 @@
 					     <37 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
+			sdmmca-ecc@ff8c2c00 {
+				compatible = "altr,socfpga-sdmmc-ecc";
+				reg = <0xff8c2c00 0x400>;
+				altr,ecc-parent = <&mmc>;
+				interrupts = <15 IRQ_TYPE_LEVEL_HIGH>,
+					     <47 IRQ_TYPE_LEVEL_HIGH>,
+					     <16 IRQ_TYPE_LEVEL_HIGH>,
+					     <48 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
 			dma-ecc@ff8c8000 {
 				compatible = "altr,socfpga-dma-ecc";
 				reg = <0xff8c8000 0x400>;
@@ -837,7 +845,7 @@
 			reset-names = "timer";
 		};
 
-		uart0: serial0@ffc02000 {
+		uart0: serial@ffc02000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0xffc02000 0x100>;
 			interrupts = <0 110 IRQ_TYPE_LEVEL_HIGH>;
@@ -848,7 +856,7 @@
 			status = "disabled";
 		};
 
-		uart1: serial1@ffc02100 {
+		uart1: serial@ffc02100 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0xffc02100 0x100>;
 			interrupts = <0 111 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_chameleonv3.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_chameleonv3.dts
new file mode 100644
index 000000000000..422d00cd4c74
--- /dev/null
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_chameleonv3.dts
@@ -0,0 +1,90 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2022 Google LLC
+ */
+/dts-v1/;
+#include "socfpga_arria10_mercury_aa1.dtsi"
+
+/ {
+	model = "Google Chameleon V3";
+	compatible = "google,chameleon-v3", "enclustra,mercury-aa1",
+		     "altr,socfpga-arria10", "altr,socfpga";
+
+	aliases {
+		serial0 = &uart0;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+	};
+};
+
+&gmac0 {
+	status = "okay";
+};
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&gpio2 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	ssm2603: audio-codec@1a {
+		compatible = "adi,ssm2603";
+		reg = <0x1a>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+
+	u80: gpio@21 {
+		compatible = "nxp,pca9535";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"SOM_AUD_MUTE",
+			"DP1_OUT_CEC_EN",
+			"DP2_OUT_CEC_EN",
+			"DP1_SOM_PS8469_CAD",
+			"DPD_SOM_PS8469_CAD",
+			"DP_OUT_PWR_EN",
+			"STM32_RST_L",
+			"STM32_BOOT0",
+
+			"FPGA_PROT",
+			"STM32_FPGA_COMM0",
+			"TP119",
+			"TP120",
+			"TP121",
+			"TP122",
+			"TP123",
+			"TP124";
+	};
+};
+
+&mmc {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "host";
+};
diff --git a/arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_mercury_aa1.dtsi
index a75c059b6727..41f865c8c098 100644
--- a/arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_mercury_aa1.dtsi
@@ -1,5 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
-/dts-v1/;
+/*
+ * Copyright 2022 Google LLC
+ */
 
 #include "socfpga_arria10.dtsi"
 
@@ -11,8 +13,6 @@
 	aliases {
 		ethernet0 = &gmac0;
 		serial1 = &uart1;
-		i2c0 = &i2c0;
-		i2c1 = &i2c1;
 	};
 
 	memory@0 {
@@ -26,24 +26,11 @@
 	};
 };
 
-&eccmgr {
-	sdmmca-ecc@ff8c2c00 {
-		compatible = "altr,socfpga-sdmmc-ecc";
-		reg = <0xff8c2c00 0x400>;
-		altr,ecc-parent = <&mmc>;
-		interrupts = <15 IRQ_TYPE_LEVEL_HIGH>,
-			     <47 IRQ_TYPE_LEVEL_HIGH>,
-			     <16 IRQ_TYPE_LEVEL_HIGH>,
-			     <48 IRQ_TYPE_LEVEL_HIGH>;
-	};
-};
-
 &gmac0 {
 	phy-mode = "rgmii";
 	phy-addr = <0xffffffff>; /* probe for phy addr */
 
 	max-frame-size = <3800>;
-	status = "okay";
 
 	phy-handle = <&phy3>;
 
@@ -69,22 +56,13 @@
 	};
 };
 
-&gpio0 {
-	status = "okay";
-};
-
-&gpio1 {
-	status = "okay";
-};
-
-&gpio2 {
-	status = "okay";
-};
-
 &i2c1 {
-	status = "okay";
+	atsha204a: crypto@64 {
+		compatible = "atmel,atsha204a";
+		reg = <0x64>;
+	};
+
 	isl12022: isl12022@6f {
-		status = "okay";
 		compatible = "isil,isl12022";
 		reg = <0x6f>;
 	};
@@ -92,21 +70,12 @@
 
 /* Following mappings are taken from arria10 socdk dts */
 &mmc {
-	status = "okay";
 	cap-sd-highspeed;
 	broken-cd;
 	bus-width = <4>;
+	clk-phase-sd-hs = <0>, <135>;
 };
 
 &osc1 {
 	clock-frequency = <33330000>;
 };
-
-&uart1 {
-	status = "okay";
-};
-
-&usb0 {
-	status = "okay";
-	dr_mode = "host";
-};
diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_mercury_pe1.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_mercury_pe1.dts
new file mode 100644
index 000000000000..cf533f76a9fd
--- /dev/null
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_mercury_pe1.dts
@@ -0,0 +1,55 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2023 Steffen Trumtrar <kernel@pengutronix.de>
+ */
+/dts-v1/;
+#include "socfpga_arria10_mercury_aa1.dtsi"
+
+/ {
+	model = "Enclustra Mercury+ PE1";
+	compatible = "enclustra,mercury-pe1", "enclustra,mercury-aa1",
+		     "altr,socfpga-arria10", "altr,socfpga";
+
+	aliases {
+		ethernet0 = &gmac0;
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+};
+
+&gmac0 {
+	status = "okay";
+};
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&gpio2 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&mmc {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "host";
+};
diff --git a/arch/arm/boot/dts/socfpga_arria10_socdk.dtsi b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk.dtsi
index ec7365444a3b..ec7365444a3b 100644
--- a/arch/arm/boot/dts/socfpga_arria10_socdk.dtsi
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk.dtsi
diff --git a/arch/arm/boot/dts/socfpga_arria10_socdk_nand.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk_nand.dts
index 9aa897b79544..a662df319a84 100644
--- a/arch/arm/boot/dts/socfpga_arria10_socdk_nand.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk_nand.dts
@@ -16,11 +16,11 @@
 
 		partition@0 {
 			label = "Boot and fpga data";
-			reg = <0x0 0x02000000>;
+			reg = <0x0 0x02500000>;
 		};
 		partition@1c00000 {
 			label = "Root Filesystem - JFFS2";
-			reg = <0x02000000 0x06000000>;
+			reg = <0x02500000 0x05500000>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/socfpga_arria10_socdk_qspi.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk_qspi.dts
index 2a745522404d..0434f1c7b665 100644
--- a/arch/arm/boot/dts/socfpga_arria10_socdk_qspi.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk_qspi.dts
@@ -9,7 +9,7 @@
 &qspi {
 	status = "okay";
 
-	flash0: n25q00@0 {
+	flash0: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,mt25qu02g", "jedec,spi-nor";
@@ -17,8 +17,6 @@
 		spi-max-frequency = <100000000>;
 
 		m25p,fast-read;
-		cdns,page-size = <256>;
-		cdns,block-size = <16>;
 		cdns,read-delay = <3>;
 		cdns,tshsl-ns = <50>;
 		cdns,tsd2d-ns = <50>;
diff --git a/arch/arm/boot/dts/socfpga_arria10_socdk_sdmmc.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk_sdmmc.dts
index 64dc0799f3d7..d3969367f4b5 100644
--- a/arch/arm/boot/dts/socfpga_arria10_socdk_sdmmc.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk_sdmmc.dts
@@ -12,6 +12,7 @@
 	cap-mmc-highspeed;
 	broken-cd;
 	bus-width = <4>;
+	clk-phase-sd-hs = <0>, <135>;
 };
 
 &eccmgr {
diff --git a/arch/arm/boot/dts/socfpga_arria5.dtsi b/arch/arm/boot/dts/intel/socfpga/socfpga_arria5.dtsi
index 22dbf07afcff..40fecde65c54 100644
--- a/arch/arm/boot/dts/socfpga_arria5.dtsi
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria5.dtsi
@@ -18,11 +18,12 @@
 			};
 		};
 
-		mmc0: dwmmc0@ff704000 {
+		mmc0: mmc@ff704000 {
 			broken-cd;
 			bus-width = <4>;
 			cap-mmc-highspeed;
 			cap-sd-highspeed;
+			clk-phase-sd-hs = <0>, <135>;
 		};
 
 		sysmgr@ffd08000 {
diff --git a/arch/arm/boot/dts/socfpga_arria5_socdk.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_arria5_socdk.dts
index 7f5458d8fccc..7342f5942b0d 100644
--- a/arch/arm/boot/dts/socfpga_arria5_socdk.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria5_socdk.dts
@@ -29,22 +29,22 @@
 
 	leds {
 		compatible = "gpio-leds";
-		hps0 {
+		led-hps0 {
 			label = "hps_led0";
 			gpios = <&porta 0 1>;
 		};
 
-		hps1 {
+		led-hps1 {
 			label = "hps_led1";
 			gpios = <&portb 11 1>;
 		};
 
-		hps2 {
+		led-hps2 {
 			label = "hps_led2";
 			gpios = <&porta 17 1>;
 		};
 
-		hps3 {
+		led-hps3 {
 			label = "hps_led3";
 			gpios = <&porta 18 1>;
 		};
@@ -124,8 +124,6 @@
 		spi-max-frequency = <100000000>;
 
 		m25p,fast-read;
-		cdns,page-size = <256>;
-		cdns,block-size = <16>;
 		cdns,read-delay = <4>;
 		cdns,tshsl-ns = <50>;
 		cdns,tsd2d-ns = <50>;
diff --git a/arch/arm/boot/dts/socfpga_cyclone5.dtsi b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5.dtsi
index 319a71e41ea4..305fe207b237 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5.dtsi
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5.dtsi
@@ -18,11 +18,12 @@
 			};
 		};
 
-		mmc0: dwmmc0@ff704000 {
+		mmc0: mmc@ff704000 {
 			broken-cd;
 			bus-width = <4>;
 			cap-mmc-highspeed;
 			cap-sd-highspeed;
+			clk-phase-sd-hs = <0>, <135>;
 		};
 
 		sysmgr@ffd08000 {
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_chameleon96.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_chameleon96.dts
index 76262f1e5e03..76262f1e5e03 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5_chameleon96.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_chameleon96.dts
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_de0_nano_soc.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_de0_nano_soc.dts
index c8f051fb2bf6..bedf577cb056 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5_de0_nano_soc.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_de0_nano_soc.dts
@@ -33,7 +33,7 @@
 
 	leds {
 		compatible = "gpio-leds";
-		hps0 {
+		led-hps0 {
 			label = "hps_led0";
 			gpios = <&portb 24 0>;
 			linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_de10nano.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_de10nano.dts
new file mode 100644
index 000000000000..ec25106caacf
--- /dev/null
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_de10nano.dts
@@ -0,0 +1,95 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2017, Intel Corporation
+ *
+ * based on socfpga_cyclone5_de0_nano_soc.dts
+ */
+/dts-v1/;
+
+#include "socfpga_cyclone5.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Terasic DE10-Nano";
+	compatible = "terasic,de10-nano", "altr,socfpga-cyclone5", "altr,socfpga";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		/* 1 GiB */
+		device_type = "memory";
+		reg = <0x0 0x40000000>;
+	};
+
+	soc {
+		fpga: bus@ff200000 {
+			compatible = "simple-bus";
+			reg = <0xff200000 0x00200000>;
+			ranges = <0x00000000 0xff200000 0x00200000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			/*
+			 * Here the devices will appear if an FPGA image is
+			 * loaded. Their description is expected to be added
+			 * using a device tree overlay that matches the image.
+			 */
+		};
+	};
+};
+
+&gmac1 {
+	/* Uses a KSZ9031RNX phy */
+	phy-mode = "rgmii-id";
+	rxd0-skew-ps = <420>;
+	rxd1-skew-ps = <420>;
+	rxd2-skew-ps = <420>;
+	rxd3-skew-ps = <420>;
+	txen-skew-ps = <0>;
+	rxdv-skew-ps = <420>;
+	status = "okay";
+};
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&gpio2 {
+	status = "okay";
+};
+
+&i2c0 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	accelerometer@53 {
+		compatible = "adi,adxl345";
+		reg = <0x53>;
+		/* HPS_GSENSOR_INT is routed to UART0_RX/CAN0_RX/SPIM0_SS1/HPS_GPIO61 */
+		interrupt-parent = <&portc>;
+		interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "INT1";
+	};
+};
+
+&mmc0 {
+	/* micro SD card socket J11 */
+	status = "okay";
+};
+
+&uart0 {
+	/*
+	 * Accessible via USB (FT232R) on Mini-USB plug J4
+	 * RX = TRACE_D0/SPIS0_CLK/UART0_RX/HPS_GPIO49
+	 * TX = TRACE_D1/SPIS0_MOSI/UART0_TX/HPS_GPIO50
+	 * no handshaking lines
+	 */
+	clock-frequency = <100000000>;
+};
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_mcv.dtsi b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_mcv.dtsi
index bd92806ffc12..3b9daddf91cd 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5_mcv.dtsi
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_mcv.dtsi
@@ -18,5 +18,6 @@
 
 &mmc0 {	/* On-SoM eMMC */
 	bus-width = <8>;
+	clk-phase-sd-hs = <0>, <135>;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_mcvevk.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_mcvevk.dts
index ceaec29770c6..c1e1264bcb09 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5_mcvevk.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_mcvevk.dts
@@ -50,8 +50,6 @@
 
 	stmpe1: stmpe811@41 {
 		compatible = "st,stmpe811";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		reg = <0x41>;
 		id = <0>;
 		blocks = <0x5>;
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_socdk.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_socdk.dts
index 253ef139181d..97622febc44e 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5_socdk.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_socdk.dts
@@ -29,22 +29,22 @@
 
 	leds {
 		compatible = "gpio-leds";
-		hps0 {
+		led-hps0 {
 			label = "hps_led0";
 			gpios = <&portb 15 1>;
 		};
 
-		hps1 {
+		led-hps1 {
 			label = "hps_led1";
 			gpios = <&portb 14 1>;
 		};
 
-		hps2 {
+		led-hps2 {
 			label = "hps_led2";
 			gpios = <&portb 13 1>;
 		};
 
-		hps3 {
+		led-hps3 {
 			label = "hps_led3";
 			gpios = <&portb 12 1>;
 		};
@@ -121,7 +121,7 @@
 &qspi {
 	status = "okay";
 
-	flash0: n25q00@0 {
+	flash0: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,mt25qu02g", "jedec,spi-nor";
@@ -129,8 +129,6 @@
 		spi-max-frequency = <100000000>;
 
 		m25p,fast-read;
-		cdns,page-size = <256>;
-		cdns,block-size = <16>;
 		cdns,read-delay = <4>;
 		cdns,tshsl-ns = <50>;
 		cdns,tsd2d-ns = <50>;
@@ -153,12 +151,6 @@
 
 &spi0 {
 	status = "okay";
-
-	spidev@0 {
-		compatible = "rohm,dh2228fv";
-		reg = <0>;
-		spi-max-frequency = <1000000>;
-	};
 };
 
 &usb1 {
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_sockit.dts
index 3dd99c7c95e0..9e4db7407f1a 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_sockit.dts
@@ -174,8 +174,6 @@
 		spi-max-frequency = <100000000>;
 
 		m25p,fast-read;
-		cdns,page-size = <256>;
-		cdns,block-size = <16>;
 		cdns,read-delay = <4>;
 		cdns,tshsl-ns = <50>;
 		cdns,tsd2d-ns = <50>;
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_socrates.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_socrates.dts
index ca18b959e655..ca18b959e655 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5_socrates.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_socrates.dts
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_sodia.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_sodia.dts
index b0003f350e65..e4794ccb8e41 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5_sodia.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_sodia.dts
@@ -66,8 +66,10 @@
 	mdio0 {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		phy0: ethernet-phy@0 {
-			reg = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		phy0: ethernet-phy@4 {
+			reg = <4>;
 			rxd0-skew-ps = <0>;
 			rxd1-skew-ps = <0>;
 			rxd2-skew-ps = <0>;
@@ -113,7 +115,7 @@
 &qspi {
 	status = "okay";
 
-	flash0: n25q512a@0 {
+	flash0: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q512a", "jedec,spi-nor";
@@ -121,8 +123,6 @@
 		spi-max-frequency = <100000000>;
 
 		m25p,fast-read;
-		cdns,page-size = <256>;
-		cdns,block-size = <16>;
 		cdns,read-delay = <4>;
 		cdns,tshsl-ns = <50>;
 		cdns,tsd2d-ns = <50>;
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_vining_fpga.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_vining_fpga.dts
index 25874e1b9c82..170c1ae441a6 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5_vining_fpga.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_vining_fpga.dts
@@ -130,18 +130,18 @@
 		#gpio-cells = <2>;
 	};
 
-	temp: lm75@48 {
-		compatible = "lm75";
+	temp: temperature-sensor@48 {
+		compatible = "national,lm75";
 		reg = <0x48>;
 	};
 
-	at24@50 {
+	eeprom@50 {
 		compatible = "atmel,24c01";
 		pagesize = <8>;
 		reg = <0x50>;
 	};
 
-	i2cswitch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -211,7 +211,7 @@
 	status = "okay";
 	clock-frequency = <100000>;
 
-	at24@50 {
+	eeprom@50 {
 		compatible = "atmel,24c02";
 		pagesize = <8>;
 		reg = <0x50>;
@@ -221,7 +221,7 @@
 &qspi {
 	status = "okay";
 
-	n25q128@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q128", "jedec,spi-nor";
@@ -229,8 +229,6 @@
 		spi-max-frequency = <100000000>;
 		m25p,fast-read;
 
-		cdns,page-size = <256>;
-		cdns,block-size = <16>;
 		cdns,read-delay = <4>;
 		cdns,tshsl-ns = <50>;
 		cdns,tsd2d-ns = <50>;
@@ -238,7 +236,7 @@
 		cdns,tslch-ns = <4>;
 	};
 
-	n25q00@1 {
+	flash@1 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,mt25qu02g", "jedec,spi-nor";
@@ -246,8 +244,6 @@
 		spi-max-frequency = <100000000>;
 		m25p,fast-read;
 
-		cdns,page-size = <256>;
-		cdns,block-size = <16>;
 		cdns,read-delay = <4>;
 		cdns,tshsl-ns = <50>;
 		cdns,tsd2d-ns = <50>;
diff --git a/arch/arm/boot/dts/socfpga_vt.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_vt.dts
index a77846f73b34..845ab2cc5ce6 100644
--- a/arch/arm/boot/dts/socfpga_vt.dts
+++ b/arch/arm/boot/dts/intel/socfpga/socfpga_vt.dts
@@ -29,7 +29,7 @@
 			};
 		};
 
-		dwmmc0@ff704000 {
+		mmc@ff704000 {
 			broken-cd;
 			bus-width = <4>;
 			cap-mmc-highspeed;
@@ -57,11 +57,11 @@
 			clock-frequency = <7000000>;
 		};
 
-		serial0@ffc02000 {
+		serial@ffc02000 {
 			clock-frequency = <7372800>;
 		};
 
-		serial1@ffc03000 {
+		serial@ffc03000 {
 			clock-frequency = <7372800>;
 		};
 
diff --git a/arch/arm/boot/dts/kirkwood-rd88f6192.dts b/arch/arm/boot/dts/kirkwood-rd88f6192.dts
deleted file mode 100644
index 712d6042b132..000000000000
--- a/arch/arm/boot/dts/kirkwood-rd88f6192.dts
+++ /dev/null
@@ -1,106 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Marvell RD88F6192 Board descrition
- *
- * Andrew Lunn <andrew@lunn.ch>
- *
- * This file contains the definitions that are common between the three
- * variants of the Marvell Kirkwood Development Board.
- */
-/dts-v1/;
-
-#include "kirkwood.dtsi"
-#include "kirkwood-6192.dtsi"
-
-/ {
-	model = "Marvell RD88F6192 reference design";
-	compatible = "marvell,rd88f6192", "marvell,kirkwood-88f6192", "marvell,kirkwood";
-
-	memory {
-		device_type = "memory";
-		reg = <0x00000000 0x20000000>;
-	};
-
-	chosen {
-		bootargs = "console=ttyS0,115200n8";
-		stdout-path = &uart0;
-	};
-
-	ocp@f1000000 {
-		pinctrl: pin-controller@10000 {
-			pinctrl-0 = <&pmx_usb_power>;
-			pinctrl-names = "default";
-
-                        pmx_usb_power: pmx-usb-power {
-                                marvell,pins = "mpp10";
-                                marvell,function = "gpo";
-                        };
-		};
-
-		serial@12000 {
-			status = "okay";
-
-		};
-
-		spi@10600 {
-			status = "okay";
-
-			m25p128@0 {
-				#address-cells = <1>;
-				#size-cells = <1>;
-				compatible = "st,m25p128", "jedec,spi-nor";
-				reg = <0>;
-				spi-max-frequency = <20000000>;
-				mode = <0>;
-			};
-		};
-
-		sata@80000 {
-			status = "okay";
-			nr-ports = <2>;
-		};
-	};
-
-	regulators {
-                compatible = "simple-bus";
-                #address-cells = <1>;
-                #size-cells = <0>;
-                pinctrl-0 = <&pmx_usb_power>;
-                pinctrl-names = "default";
-
-                usb_power: regulator@0 {
-                        compatible = "regulator-fixed";
-                        reg = <0>;
-                        regulator-name = "USB VBUS";
-                        regulator-min-microvolt = <5000000>;
-                        regulator-max-microvolt = <5000000>;
-                        enable-active-high;
-                        regulator-always-on;
-                        regulator-boot-on;
-                        gpio = <&gpio0 10 GPIO_ACTIVE_HIGH>;
-                };
-	};
-};
-
-&mdio {
-        status = "okay";
-
-        ethphy0: ethernet-phy@8 {
-                reg = <8>;
-        };
-};
-
-&eth0 {
-        status = "okay";
-        ethernet0-port@0 {
-                phy-handle = <&ethphy0>;
-        };
-};
-
-&pciec {
-        status = "okay";
-};
-
-&pcie0 {
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/lan966x-pcb8291.dts b/arch/arm/boot/dts/lan966x-pcb8291.dts
deleted file mode 100644
index 3281af90ac6d..000000000000
--- a/arch/arm/boot/dts/lan966x-pcb8291.dts
+++ /dev/null
@@ -1,64 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * lan966x_pcb8291.dts - Device Tree file for PCB8291
- */
-/dts-v1/;
-#include "lan966x.dtsi"
-
-/ {
-	model = "Microchip EVB - LAN9662";
-	compatible = "microchip,lan9662-pcb8291", "microchip,lan9662", "microchip,lan966";
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	aliases {
-		serial0 = &usart3;
-	};
-};
-
-&gpio {
-	fc_shrd7_pins: fc_shrd7-pins {
-		pins = "GPIO_49";
-		function = "fc_shrd7";
-	};
-
-	fc_shrd8_pins: fc_shrd8-pins {
-		pins = "GPIO_54";
-		function = "fc_shrd8";
-	};
-
-	fc3_b_pins: fcb3-spi-pins {
-		/* SCK, RXD, TXD */
-		pins = "GPIO_51", "GPIO_52", "GPIO_53";
-		function = "fc3_b";
-	};
-
-	can0_b_pins:  can0_b_pins {
-		/* RX, TX */
-		pins = "GPIO_35", "GPIO_36";
-		function = "can0_b";
-	};
-};
-
-&can0 {
-	pinctrl-0 = <&can0_b_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&flx3 {
-	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
-	status = "okay";
-
-	usart3: serial@200 {
-		pinctrl-0 = <&fc3_b_pins>, <&fc_shrd7_pins>, <&fc_shrd8_pins>;
-		pinctrl-names = "default";
-		status = "okay";
-	};
-};
-
-&watchdog {
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/lan966x.dtsi b/arch/arm/boot/dts/lan966x.dtsi
deleted file mode 100644
index 7d2869648050..000000000000
--- a/arch/arm/boot/dts/lan966x.dtsi
+++ /dev/null
@@ -1,237 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * lan966x.dtsi - Device Tree Include file for Microchip LAN966 family SoC
- *
- * Copyright (C) 2021 Microchip Technology, Inc. and its subsidiaries
- *
- * Author: Kavyasree Kotagiri <kavyasree.kotagiri@microchip.com>
- *
- */
-
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/mfd/atmel-flexcom.h>
-#include <dt-bindings/dma/at91.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/clock/microchip,lan966x.h>
-
-/ {
-	model = "Microchip LAN966 family SoC";
-	compatible = "microchip,lan966";
-	interrupt-parent = <&gic>;
-	#address-cells = <1>;
-	#size-cells = <1>;
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu@0 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a7";
-			clock-frequency = <600000000>;
-			reg = <0x0>;
-		};
-	};
-
-	clocks {
-		sys_clk: sys_clk {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <162500000>;
-		};
-
-		cpu_clk: cpu_clk {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <600000000>;
-		};
-
-		ddr_clk: ddr_clk {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <300000000>;
-		};
-
-		nic_clk: nic_clk {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <200000000>;
-		};
-	};
-
-	clks: clock-controller@e00c00a8 {
-		compatible = "microchip,lan966x-gck";
-		#clock-cells = <1>;
-		clocks = <&cpu_clk>, <&ddr_clk>, <&sys_clk>;
-		clock-names = "cpu", "ddr", "sys";
-		reg = <0xe00c00a8 0x38>;
-	};
-
-	timer {
-		compatible = "arm,armv7-timer";
-		interrupt-parent = <&gic>;
-		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
-			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
-			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
-			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
-		clock-frequency = <37500000>;
-	};
-
-	soc {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		flx0: flexcom@e0040000 {
-			compatible = "atmel,sama5d2-flexcom";
-			reg = <0xe0040000 0x100>;
-			clocks = <&clks GCK_ID_FLEXCOM0>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x0 0xe0040000 0x800>;
-			status = "disabled";
-		};
-
-		flx1: flexcom@e0044000 {
-			compatible = "atmel,sama5d2-flexcom";
-			reg = <0xe0044000 0x100>;
-			clocks = <&clks GCK_ID_FLEXCOM1>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x0 0xe0044000 0x800>;
-			status = "disabled";
-		};
-
-		trng: rng@e0048000 {
-			compatible = "atmel,at91sam9g45-trng";
-			reg = <0xe0048000 0x100>;
-			clocks = <&nic_clk>;
-		};
-
-		aes: crypto@e004c000 {
-			compatible = "atmel,at91sam9g46-aes";
-			reg = <0xe004c000 0x100>;
-			interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&dma0 AT91_XDMAC_DT_PERID(13)>,
-			       <&dma0 AT91_XDMAC_DT_PERID(12)>;
-			dma-names = "rx", "tx";
-			clocks = <&nic_clk>;
-			clock-names = "aes_clk";
-		};
-
-		flx2: flexcom@e0060000 {
-			compatible = "atmel,sama5d2-flexcom";
-			reg = <0xe0060000 0x100>;
-			clocks = <&clks GCK_ID_FLEXCOM2>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x0 0xe0060000 0x800>;
-			status = "disabled";
-		};
-
-		flx3: flexcom@e0064000 {
-			compatible = "atmel,sama5d2-flexcom";
-			reg = <0xe0064000 0x100>;
-			clocks = <&clks GCK_ID_FLEXCOM3>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x0 0xe0064000 0x800>;
-			status = "disabled";
-
-			usart3: serial@200 {
-				compatible = "atmel,at91sam9260-usart";
-				reg = <0x200 0x200>;
-				interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&nic_clk>;
-				clock-names = "usart";
-				atmel,fifo-size = <32>;
-				status = "disabled";
-			};
-		};
-
-		dma0: dma-controller@e0068000 {
-			compatible = "microchip,sama7g5-dma";
-			reg = <0xe0068000 0x1000>;
-			interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
-			#dma-cells = <1>;
-			clocks = <&nic_clk>;
-			clock-names = "dma_clk";
-		};
-
-		sha: crypto@e006c000 {
-			compatible = "atmel,at91sam9g46-sha";
-			reg = <0xe006c000 0xec>;
-			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&dma0 AT91_XDMAC_DT_PERID(14)>;
-			dma-names = "tx";
-			clocks = <&nic_clk>;
-			clock-names = "sha_clk";
-		};
-
-		flx4: flexcom@e0070000 {
-			compatible = "atmel,sama5d2-flexcom";
-			reg = <0xe0070000 0x100>;
-			clocks = <&clks GCK_ID_FLEXCOM4>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x0 0xe0070000 0x800>;
-			status = "disabled";
-		};
-
-		timer0: timer@e008c000 {
-			compatible = "snps,dw-apb-timer";
-			reg = <0xe008c000 0x400>;
-			clocks = <&nic_clk>;
-			clock-names = "timer";
-			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
-		};
-
-		watchdog: watchdog@e0090000 {
-			compatible = "snps,dw-wdt";
-			reg = <0xe0090000 0x1000>;
-			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&nic_clk>;
-			status = "disabled";
-		};
-
-		can0: can@e081c000 {
-			compatible = "bosch,m_can";
-			reg = <0xe081c000 0xfc>, <0x00100000 0x4000>;
-			reg-names = "m_can", "message_ram";
-			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "int0", "int1";
-			clocks = <&clks GCK_ID_MCAN0>, <&clks GCK_ID_MCAN0>;
-			clock-names = "hclk", "cclk";
-			assigned-clocks = <&clks GCK_ID_MCAN0>;
-			assigned-clock-rates = <40000000>;
-			bosch,mram-cfg = <0x0 0 0 64 0 0 32 32>;
-			status = "disabled";
-		};
-
-		gpio: pinctrl@e2004064 {
-			compatible = "microchip,lan966x-pinctrl";
-			reg = <0xe2004064 0xb4>,
-			    <0xe2010024 0x138>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			gpio-ranges = <&gpio 0 0 78>;
-			interrupt-controller;
-			interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
-			#interrupt-cells = <2>;
-		};
-
-		gic: interrupt-controller@e8c11000 {
-			compatible = "arm,gic-400", "arm,cortex-a7-gic";
-			#interrupt-cells = <3>;
-			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-controller;
-			reg = <0xe8c11000 0x1000>,
-			      <0xe8c12000 0x2000>,
-			      <0xe8c14000 0x2000>,
-			      <0xe8c16000 0x2000>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/logicpd-som-lv-35xx-devkit.dts b/arch/arm/boot/dts/logicpd-som-lv-35xx-devkit.dts
deleted file mode 100644
index 2a0a98fe67f0..000000000000
--- a/arch/arm/boot/dts/logicpd-som-lv-35xx-devkit.dts
+++ /dev/null
@@ -1,13 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-
-/dts-v1/;
-
-#include "omap34xx.dtsi"
-#include "logicpd-som-lv.dtsi"
-#include "logicpd-som-lv-baseboard.dtsi"
-#include "omap-gpmc-smsc9221.dtsi"
-
-/ {
-	model = "LogicPD Zoom OMAP35xx SOM-LV Development Kit";
-	compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3430", "ti,omap3";
-};
diff --git a/arch/arm/boot/dts/logicpd-som-lv-37xx-devkit.dts b/arch/arm/boot/dts/logicpd-som-lv-37xx-devkit.dts
deleted file mode 100644
index a604d92221a4..000000000000
--- a/arch/arm/boot/dts/logicpd-som-lv-37xx-devkit.dts
+++ /dev/null
@@ -1,13 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-
-/dts-v1/;
-
-#include "omap36xx.dtsi"
-#include "logicpd-som-lv.dtsi"
-#include "logicpd-som-lv-baseboard.dtsi"
-#include "omap-gpmc-smsc9221.dtsi"
-
-/ {
-	model = "LogicPD Zoom DM3730 SOM-LV Development Kit";
-	compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3630", "ti,omap3";
-};
diff --git a/arch/arm/boot/dts/marvell/Makefile b/arch/arm/boot/dts/marvell/Makefile
new file mode 100644
index 000000000000..1e0f5ff492f7
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/Makefile
@@ -0,0 +1,165 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_MMP) += \
+	pxa168-aspenite.dtb \
+	pxa910-dkb.dtb \
+	mmp2-brownstone.dtb \
+	mmp2-olpc-xo-1-75.dtb \
+	mmp3-dell-ariel.dtb
+dtb-$(CONFIG_ARCH_ORION5X) += \
+	orion5x-kuroboxpro.dtb \
+	orion5x-lacie-d2-network.dtb \
+	orion5x-lacie-ethernet-disk-mini-v2.dtb \
+	orion5x-linkstation-lsgl.dtb \
+	orion5x-linkstation-lswtgl.dtb \
+	orion5x-linkstation-lschl.dtb \
+	orion5x-lswsgl.dtb \
+	orion5x-maxtor-shared-storage-2.dtb \
+	orion5x-netgear-wnr854t.dtb \
+	orion5x-rd88f5182-nas.dtb
+dtb-$(CONFIG_MACH_ARMADA_370) += \
+	armada-370-c200-v2.dtb \
+	armada-370-db.dtb \
+	armada-370-dlink-dns327l.dtb \
+	armada-370-mirabox.dtb \
+	armada-370-netgear-rn102.dtb \
+	armada-370-netgear-rn104.dtb \
+	armada-370-rd.dtb \
+	armada-370-seagate-nas-2bay.dtb \
+	armada-370-seagate-nas-4bay.dtb \
+	armada-370-seagate-personal-cloud.dtb \
+	armada-370-seagate-personal-cloud-2bay.dtb \
+	armada-370-synology-ds213j.dtb
+dtb-$(CONFIG_MACH_ARMADA_375) += \
+	armada-375-db.dtb
+dtb-$(CONFIG_MACH_ARMADA_38X) += \
+	armada-381-netgear-gs110emx.dtb \
+	armada-382-rd-ac3x-48g4x2xl.dtb \
+	armada-385-atl-x530.dtb \
+	armada-385-clearfog-gtr-s4.dtb \
+	armada-385-clearfog-gtr-l8.dtb \
+	armada-385-db-88f6820-amc.dtb \
+	armada-385-db-ap.dtb \
+	armada-385-linksys-caiman.dtb \
+	armada-385-linksys-cobra.dtb \
+	armada-385-linksys-rango.dtb \
+	armada-385-linksys-shelby.dtb \
+	armada-385-synology-ds116.dtb \
+	armada-385-turris-omnia.dtb \
+	armada-388-clearfog.dtb \
+	armada-388-clearfog-base.dtb \
+	armada-388-clearfog-pro.dtb \
+	armada-388-db.dtb \
+	armada-388-gp.dtb \
+	armada-388-helios4.dtb \
+	armada-388-rd.dtb
+dtb-$(CONFIG_MACH_ARMADA_39X) += \
+	armada-390-db.dtb \
+	armada-395-gp.dtb \
+	armada-398-db.dtb
+dtb-$(CONFIG_MACH_ARMADA_XP) += \
+	armada-xp-axpwifiap.dtb \
+	armada-xp-crs305-1g-4s.dtb \
+	armada-xp-crs305-1g-4s-bit.dtb \
+	armada-xp-crs326-24g-2s.dtb \
+	armada-xp-crs326-24g-2s-bit.dtb \
+	armada-xp-crs328-4c-20s-4s.dtb \
+	armada-xp-crs328-4c-20s-4s-bit.dtb \
+	armada-xp-db.dtb \
+	armada-xp-db-dxbc2.dtb \
+	armada-xp-db-xc3-24g4xg.dtb \
+	armada-xp-gp.dtb \
+	armada-xp-lenovo-ix4-300d.dtb \
+	armada-xp-linksys-mamba.dtb \
+	armada-xp-matrix.dtb \
+	armada-xp-netgear-rn2120.dtb \
+	armada-xp-openblocks-ax3-4.dtb \
+	armada-xp-synology-ds414.dtb
+dtb-$(CONFIG_MACH_DOVE) += \
+	dove-cubox.dtb \
+	dove-cubox-es.dtb \
+	dove-d2plug.dtb \
+	dove-d3plug.dtb \
+	dove-dove-db.dtb \
+	dove-sbc-a510.dtb
+dtb-$(CONFIG_MACH_KIRKWOOD) += \
+	kirkwood-4i-edge-200.dtb \
+	kirkwood-b3.dtb \
+	kirkwood-blackarmor-nas220.dtb \
+	kirkwood-c200-v1.dtb \
+	kirkwood-cloudbox.dtb \
+	kirkwood-d2net.dtb \
+	kirkwood-db-88f6281.dtb \
+	kirkwood-db-88f6282.dtb \
+	kirkwood-dir665.dtb \
+	kirkwood-dns320.dtb \
+	kirkwood-dns325.dtb \
+	kirkwood-dockstar.dtb \
+	kirkwood-dreamplug.dtb \
+	kirkwood-ds109.dtb \
+	kirkwood-ds110jv10.dtb \
+	kirkwood-ds111.dtb \
+	kirkwood-ds112.dtb \
+	kirkwood-ds209.dtb \
+	kirkwood-ds210.dtb \
+	kirkwood-ds212.dtb \
+	kirkwood-ds212j.dtb \
+	kirkwood-ds409.dtb \
+	kirkwood-ds409slim.dtb \
+	kirkwood-ds411.dtb \
+	kirkwood-ds411j.dtb \
+	kirkwood-ds411slim.dtb \
+	kirkwood-goflexnet.dtb \
+	kirkwood-guruplug-server-plus.dtb \
+	kirkwood-ib62x0.dtb \
+	kirkwood-iconnect.dtb \
+	kirkwood-iomega_ix2_200.dtb \
+	kirkwood-is2.dtb \
+	kirkwood-km_fixedeth.dtb \
+	kirkwood-km_kirkwood.dtb \
+	kirkwood-l-50.dtb \
+	kirkwood-laplug.dtb \
+	kirkwood-linkstation-lsqvl.dtb \
+	kirkwood-linkstation-lsvl.dtb \
+	kirkwood-linkstation-lswsxl.dtb \
+	kirkwood-linkstation-lswvl.dtb \
+	kirkwood-linkstation-lswxl.dtb \
+	kirkwood-linksys-viper.dtb \
+	kirkwood-lschlv2.dtb \
+	kirkwood-lsxhl.dtb \
+	kirkwood-mplcec4.dtb \
+	kirkwood-mv88f6281gtw-ge.dtb \
+	kirkwood-nas2big.dtb \
+	kirkwood-net2big.dtb \
+	kirkwood-net5big.dtb \
+	kirkwood-netgear_readynas_duo_v2.dtb \
+	kirkwood-netgear_readynas_nv+_v2.dtb \
+	kirkwood-ns2.dtb \
+	kirkwood-ns2lite.dtb \
+	kirkwood-ns2max.dtb \
+	kirkwood-ns2mini.dtb \
+	kirkwood-nsa310.dtb \
+	kirkwood-nsa310a.dtb \
+	kirkwood-nsa310s.dtb \
+	kirkwood-nsa320.dtb \
+	kirkwood-nsa325.dtb \
+	kirkwood-openblocks_a6.dtb \
+	kirkwood-openblocks_a7.dtb \
+	kirkwood-openrd-base.dtb \
+	kirkwood-openrd-client.dtb \
+	kirkwood-openrd-ultimate.dtb \
+	kirkwood-pogo_e02.dtb \
+	kirkwood-pogoplug-series-4.dtb \
+	kirkwood-rd88f6192.dtb \
+	kirkwood-rd88f6281-z0.dtb \
+	kirkwood-rd88f6281-a.dtb \
+	kirkwood-rs212.dtb \
+	kirkwood-rs409.dtb \
+	kirkwood-rs411.dtb \
+	kirkwood-sheevaplug.dtb \
+	kirkwood-sheevaplug-esata.dtb \
+	kirkwood-t5325.dtb \
+	kirkwood-topkick.dtb \
+	kirkwood-ts219-6281.dtb \
+	kirkwood-ts219-6282.dtb \
+	kirkwood-ts419-6281.dtb \
+	kirkwood-ts419-6282.dtb
diff --git a/arch/arm/boot/dts/armada-370-c200-v2.dts b/arch/arm/boot/dts/marvell/armada-370-c200-v2.dts
index 1a4a09bdde63..84d40e1d70ef 100644
--- a/arch/arm/boot/dts/armada-370-c200-v2.dts
+++ b/arch/arm/boot/dts/marvell/armada-370-c200-v2.dts
@@ -75,25 +75,25 @@
 		pinctrl-0 = <&pmx_buttons>;
 		pinctrl-names = "default";
 
-		power {
+		button-power {
 			label = "Power Button";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio0 10 GPIO_ACTIVE_HIGH>;
 		};
 
-		reset {
+		button-reset {
 			label = "Reset Button";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
 		};
 
-		usb1 {
+		button-usb1 {
 			label = "USB1 Button";
 			linux,code = <BTN_0>;
 			gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
 		};
 
-		usb2 {
+		button-usb2 {
 			label = "USB2 Button";
 			linux,code = <BTN_1>;
 			gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/armada-370-db.dts b/arch/arm/boot/dts/marvell/armada-370-db.dts
index 77261a2fb949..a9a05d826f22 100644
--- a/arch/arm/boot/dts/armada-370-db.dts
+++ b/arch/arm/boot/dts/marvell/armada-370-db.dts
@@ -119,7 +119,7 @@
 			"Out Jack", "HPL",
 			"Out Jack", "HPR",
 			"AIN1L", "In Jack",
-			"AIN1L", "In Jack";
+			"AIN1R", "In Jack";
 		status = "okay";
 
 		simple-audio-card,dai-link@0 {
@@ -203,7 +203,7 @@
 	pinctrl-names = "default";
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "mx25l25635e", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-370-dlink-dns327l.dts b/arch/arm/boot/dts/marvell/armada-370-dlink-dns327l.dts
index 2008c6eaaa52..d4c4efabd254 100644
--- a/arch/arm/boot/dts/armada-370-dlink-dns327l.dts
+++ b/arch/arm/boot/dts/marvell/armada-370-dlink-dns327l.dts
@@ -86,73 +86,64 @@
 
 		pinctrl-names = "default";
 
-		sata-r-amber-pin {
+		led-sata-r-amber {
 			label = "dns327l:amber:sata-r";
 			gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
 		};
 
-		sata-l-amber-pin {
+		led-sata-l-amber {
 			label = "dns327l:amber:sata-l";
 			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
 		};
 
-		backup-led-pin {
+		led-backup {
 			label = "dns327l:white:usb";
 			gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		usb_power: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			pinctrl-0 = <&xhci_pwr_pin>;
-			pinctrl-names = "default";
-			regulator-name = "USB3.0 Port Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			regulator-boot-on;
-			regulator-always-on;
-			gpio = <&gpio0 13 GPIO_ACTIVE_HIGH>;
-		};
+	usb_power: regulator-1 {
+		compatible = "regulator-fixed";
+		pinctrl-0 = <&xhci_pwr_pin>;
+		pinctrl-names = "default";
+		regulator-name = "USB3.0 Port Power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-boot-on;
+		regulator-always-on;
+		gpio = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+	};
 
-		sata_r_power: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			pinctrl-0 = <&sata_r_pwr_pin>;
-			pinctrl-names = "default";
-			regulator-name = "SATA-R Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			startup-delay-us = <2000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
-		};
+	sata_r_power: regulator-2 {
+		compatible = "regulator-fixed";
+		pinctrl-0 = <&sata_r_pwr_pin>;
+		pinctrl-names = "default";
+		regulator-name = "SATA-R Power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		startup-delay-us = <2000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+	};
 
-		sata_l_power: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			pinctrl-0 = <&sata_l_pwr_pin>;
-			pinctrl-names = "default";
-			regulator-name = "SATA-L Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			startup-delay-us = <4000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio1 24 GPIO_ACTIVE_HIGH>;
-		};
+	sata_l_power: regulator-3 {
+		compatible = "regulator-fixed";
+		pinctrl-0 = <&sata_l_pwr_pin>;
+		pinctrl-names = "default";
+		regulator-name = "SATA-L Power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		startup-delay-us = <4000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 24 GPIO_ACTIVE_HIGH>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/armada-370-mirabox.dts b/arch/arm/boot/dts/marvell/armada-370-mirabox.dts
index 7c2f5a79b50d..7c2f5a79b50d 100644
--- a/arch/arm/boot/dts/armada-370-mirabox.dts
+++ b/arch/arm/boot/dts/marvell/armada-370-mirabox.dts
diff --git a/arch/arm/boot/dts/armada-370-netgear-rn102.dts b/arch/arm/boot/dts/marvell/armada-370-netgear-rn102.dts
index b0b640b7de40..079b37cf148a 100644
--- a/arch/arm/boot/dts/armada-370-netgear-rn102.dts
+++ b/arch/arm/boot/dts/marvell/armada-370-netgear-rn102.dts
@@ -85,11 +85,11 @@
 	};
 
 	clocks {
-	       g762_clk: g762-oscillator {
-			 compatible = "fixed-clock";
-			 #clock-cells = <0>;
-			 clock-frequency = <8192>;
-	       };
+		g762_clk: g762-oscillator {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <8192>;
+		};
 	};
 
 	gpio-leds {
diff --git a/arch/arm/boot/dts/armada-370-netgear-rn104.dts b/arch/arm/boot/dts/marvell/armada-370-netgear-rn104.dts
index 85e2e9e27a9f..d752ac1d7b58 100644
--- a/arch/arm/boot/dts/armada-370-netgear-rn104.dts
+++ b/arch/arm/boot/dts/marvell/armada-370-netgear-rn104.dts
@@ -94,11 +94,11 @@
 	};
 
 	clocks {
-	       g762_clk: g762-oscillator {
-			 compatible = "fixed-clock";
-			 #clock-cells = <0>;
-			 clock-frequency = <8192>;
-	       };
+		g762_clk: g762-oscillator {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <8192>;
+		};
 	};
 
 	gpio-leds {
diff --git a/arch/arm/boot/dts/armada-370-rd.dts b/arch/arm/boot/dts/marvell/armada-370-rd.dts
index c910d157a686..f23f6b3fc8f3 100644
--- a/arch/arm/boot/dts/armada-370-rd.dts
+++ b/arch/arm/boot/dts/marvell/armada-370-rd.dts
@@ -20,6 +20,7 @@
 /dts-v1/;
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/gpio/gpio.h>
 #include "armada-370.dtsi"
 
@@ -61,8 +62,8 @@
 				status = "okay";
 				phy-mode = "rgmii-id";
 				fixed-link {
-					   speed = <1000>;
-					   full-duplex;
+					speed = <1000>;
+					full-duplex;
 				};
 			};
 
@@ -84,8 +85,6 @@
 
 			gpio-keys {
 				compatible = "gpio-keys";
-				#address-cells = <1>;
-				#size-cells = <0>;
 				button {
 					label = "Software Button";
 					linux,code = <KEY_POWER>;
@@ -96,7 +95,7 @@
 			gpio-fan {
 				compatible = "gpio-fan";
 				gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
-				gpio-fan,speed-map = <0 0 3000 1>;
+				gpio-fan,speed-map = <0 0>, <3000 1>;
 				pinctrl-0 = <&fan_pins>;
 				pinctrl-names = "default";
 			};
@@ -137,44 +136,53 @@
 	pinctrl-names = "default";
 	phy0: ethernet-phy@0 {
 		reg = <0>;
+		leds {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			led@0 {
+				reg = <0>;
+				color = <LED_COLOR_ID_WHITE>;
+				function = LED_FUNCTION_WAN;
+				default-state = "keep";
+			};
+		};
 	};
 
-	switch: switch@10 {
+	switch: ethernet-switch@10 {
 		compatible = "marvell,mv88e6085";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		reg = <0x10>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 
-		ports {
+		ethernet-ports {
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			port@0 {
+			ethernet-port@0 {
 				reg = <0>;
 				label = "lan0";
 			};
 
-			port@1 {
-			       reg = <1>;
-			       label = "lan1";
+			ethernet-port@1 {
+				reg = <1>;
+				label = "lan1";
 			};
 
-			port@2 {
-			       reg = <2>;
-			       label = "lan2";
+			ethernet-port@2 {
+				reg = <2>;
+				label = "lan2";
 			};
 
-			port@3 {
-			       reg = <3>;
-			       label = "lan3";
+			ethernet-port@3 {
+				reg = <3>;
+				label = "lan3";
 			};
 
-			port@5 {
+			ethernet-port@5 {
 				reg = <5>;
-				label = "cpu";
 				ethernet = <&eth1>;
+				phy-mode = "rgmii-id";
 				fixed-link {
 					speed = <1000>;
 					full-duplex;
@@ -186,25 +194,25 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			switchphy0: switchphy@0 {
+			switchphy0: ethernet-phy@0 {
 				reg = <0>;
 				interrupt-parent = <&switch>;
 				interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
-			switchphy1: switchphy@1 {
+			switchphy1: ethernet-phy@1 {
 				reg = <1>;
 				interrupt-parent = <&switch>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
-			switchphy2: switchphy@2 {
+			switchphy2: ethernet-phy@2 {
 				reg = <2>;
 				interrupt-parent = <&switch>;
 				interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
-			switchphy3: switchphy@3 {
+			switchphy3: ethernet-phy@3 {
 				reg = <3>;
 				interrupt-parent = <&switch>;
 				interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/armada-370-seagate-nas-2bay.dts b/arch/arm/boot/dts/marvell/armada-370-seagate-nas-2bay.dts
index 8dd242e668e6..6ec3dd3337f4 100644
--- a/arch/arm/boot/dts/armada-370-seagate-nas-2bay.dts
+++ b/arch/arm/boot/dts/marvell/armada-370-seagate-nas-2bay.dts
@@ -25,9 +25,9 @@
 
 	gpio-fan {
 		gpio-fan,speed-map =
-			<   0 3
-			  950 2
-			 1400 1
-			 1800 0>;
+			<   0 3>,
+			< 950 2>,
+			<1400 1>,
+			<1800 0>;
 	};
 };
diff --git a/arch/arm/boot/dts/armada-370-seagate-nas-4bay.dts b/arch/arm/boot/dts/marvell/armada-370-seagate-nas-4bay.dts
index 3cf70c72c5ca..3011578a3124 100644
--- a/arch/arm/boot/dts/armada-370-seagate-nas-4bay.dts
+++ b/arch/arm/boot/dts/marvell/armada-370-seagate-nas-4bay.dts
@@ -46,37 +46,34 @@
 		};
 	};
 
-	regulators {
-		regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "SATA2 power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&pca9554 6 GPIO_ACTIVE_HIGH>;
-		};
-		regulator@4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			regulator-name = "SATA3 power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&pca9554 7 GPIO_ACTIVE_HIGH>;
-		};
+	regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "SATA2 power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&pca9554 6 GPIO_ACTIVE_HIGH>;
+	};
+
+	regulator-4 {
+		compatible = "regulator-fixed";
+		regulator-name = "SATA3 power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&pca9554 7 GPIO_ACTIVE_HIGH>;
 	};
 
 	gpio-leds {
-		red-sata2 {
+		led-red-sata2 {
 			label = "dart:red:sata2";
 			gpios = <&pca9554 0 GPIO_ACTIVE_LOW>;
 		};
-		red-sata3 {
+		led-red-sata3 {
 			label = "dart:red:sata3";
 			gpios = <&pca9554 3 GPIO_ACTIVE_LOW>;
 		};
@@ -109,10 +106,10 @@
 
 	gpio-fan {
 		gpio-fan,speed-map =
-			<   0 3
-			  800 2
-			  1050 1
-			  1300 0>;
+			<   0 3>,
+			< 800 2>,
+			<1050 1>,
+			<1300 0>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/armada-370-seagate-nas-xbay.dtsi b/arch/arm/boot/dts/marvell/armada-370-seagate-nas-xbay.dtsi
index b52634ecf1d9..ffb3179033e7 100644
--- a/arch/arm/boot/dts/armada-370-seagate-nas-xbay.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-370-seagate-nas-xbay.dtsi
@@ -70,34 +70,26 @@
 
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		pinctrl-names = "default";
-
-		regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "SATA0 power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio1 18 GPIO_ACTIVE_HIGH>;
-		};
-		regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "SATA1 power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
-		};
+	regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "SATA0 power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 18 GPIO_ACTIVE_HIGH>;
+	};
+
+	regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "SATA1 power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
 	};
 
 	gpio-fan {
@@ -108,22 +100,20 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		power {
+		button-power {
 			label = "Power button";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
 			debounce-interval = <100>;
 		};
-		backup {
+		button-backup {
 			label = "Backup button";
 			linux,code = <KEY_OPTION>;
 			gpios = <&gpio0 31 GPIO_ACTIVE_LOW>;
 			debounce-interval = <100>;
 		};
-		reset {
+		button-reset {
 			label = "Reset Button";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio1 23 GPIO_ACTIVE_LOW>;
@@ -134,21 +124,21 @@
 	gpio-leds {
 		compatible = "gpio-leds";
 
-		white-power {
+		led-white-power {
 			label = "dart:white:power";
 			gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "timer";
 
 		};
-		red-power {
+		led-red-power {
 			label = "dart:red:power";
 			gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
 		};
-		red-sata0 {
+		led-red-sata0 {
 			label = "dart:red:sata0";
 			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
 		};
-		red-sata1 {
+		led-red-sata1 {
 			label = "dart:red:sata1";
 			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
 		};
diff --git a/arch/arm/boot/dts/armada-370-seagate-personal-cloud-2bay.dts b/arch/arm/boot/dts/marvell/armada-370-seagate-personal-cloud-2bay.dts
index 5ee572dc9242..45d8ec5dfeb7 100644
--- a/arch/arm/boot/dts/armada-370-seagate-personal-cloud-2bay.dts
+++ b/arch/arm/boot/dts/marvell/armada-370-seagate-personal-cloud-2bay.dts
@@ -32,17 +32,14 @@
 		};
 	};
 
-	regulators {
-		regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "SATA1 power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
-		};
+	regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "SATA1 power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
 	};
 };
diff --git a/arch/arm/boot/dts/armada-370-seagate-personal-cloud.dts b/arch/arm/boot/dts/marvell/armada-370-seagate-personal-cloud.dts
index 578b54b39c8f..578b54b39c8f 100644
--- a/arch/arm/boot/dts/armada-370-seagate-personal-cloud.dts
+++ b/arch/arm/boot/dts/marvell/armada-370-seagate-personal-cloud.dts
diff --git a/arch/arm/boot/dts/armada-370-seagate-personal-cloud.dtsi b/arch/arm/boot/dts/marvell/armada-370-seagate-personal-cloud.dtsi
index a624b2371fb6..054124857235 100644
--- a/arch/arm/boot/dts/armada-370-seagate-personal-cloud.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-370-seagate-personal-cloud.dtsi
@@ -53,52 +53,43 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "USB Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio1 27 GPIO_ACTIVE_LOW>;
-		};
-		regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "SATA0 power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio1 18 GPIO_ACTIVE_HIGH>;
-		};
+	regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "USB Power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 27 GPIO_ACTIVE_LOW>;
+	};
+
+	regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "SATA0 power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 18 GPIO_ACTIVE_HIGH>;
 	};
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		power {
+		button-power {
 			label = "Power button";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
 			debounce-interval = <100>;
 		};
-		reset {
+		button-reset {
 			label = "Reset Button";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio1 23 GPIO_ACTIVE_LOW>;
 			debounce-interval = <100>;
 		};
-		button {
+		button-usb {
 			label = "USB VBUS error";
 			linux,code = <KEY_UNKNOWN>;
 			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
@@ -109,7 +100,7 @@
 	gpio-leds {
 		compatible = "gpio-leds";
 
-		red-sata0 {
+		led-red-sata0 {
 			label = "cumulus:red:sata0";
 			gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
@@ -159,7 +150,7 @@
 	pinctrl-0 = <&spi0_pins2>;
 	pinctrl-names = "default";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		/* MX25L8006E */
diff --git a/arch/arm/boot/dts/armada-370-synology-ds213j.dts b/arch/arm/boot/dts/marvell/armada-370-synology-ds213j.dts
index 64f2ce254fb6..02599a3e9816 100644
--- a/arch/arm/boot/dts/armada-370-synology-ds213j.dts
+++ b/arch/arm/boot/dts/marvell/armada-370-synology-ds213j.dts
@@ -91,9 +91,9 @@
 			};
 
 			ethernet@70000 {
-			       status = "okay";
-			       phy = <&phy1>;
-			       phy-mode = "sgmii";
+				status = "okay";
+				phy = <&phy1>;
+				phy-mode = "sgmii";
 			};
 
 			sata@a0000 {
@@ -113,14 +113,14 @@
 			 &gpio2  0 GPIO_ACTIVE_HIGH
 			 &gpio2  1 GPIO_ACTIVE_HIGH>;
 		alarm-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
-		gpio-fan,speed-map = <    0 0
-				       1000 1
-				       1150 2
-				       1350 4
-				       1500 3
-				       1650 5
-				       1750 6
-				       1900 7 >;
+		gpio-fan,speed-map = <   0 0>,
+				     <1000 1>,
+				     <1150 2>,
+				     <1350 4>,
+				     <1500 3>,
+				     <1650 5>,
+				     <1750 6>,
+				     <1900 7>;
 	};
 
 	gpio-leds {
@@ -142,38 +142,32 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		pinctrl-0 = <&sata1_pwr_pin &sata2_pwr_pin>;
+	sata1_regulator: sata1-regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "SATA1 Power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		startup-delay-us = <2000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&sata1_pwr_pin>;
 		pinctrl-names = "default";
+	};
 
-		sata1_regulator: sata1-regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "SATA1 Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			startup-delay-us = <2000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
-		};
-
-		sata2_regulator: sata2-regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "SATA2 Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			startup-delay-us = <4000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio1 30 GPIO_ACTIVE_HIGH>;
-		};
+	sata2_regulator: sata2-regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "SATA2 Power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		startup-delay-us = <4000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&sata2_pwr_pin>;
+		pinctrl-names = "default";
 	};
 };
 
@@ -258,7 +252,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q064", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-370-xp.dtsi b/arch/arm/boot/dts/marvell/armada-370-xp.dtsi
index 0b8c2a64b36f..954c891e5aee 100644
--- a/arch/arm/boot/dts/armada-370-xp.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-370-xp.dtsi
@@ -168,7 +168,6 @@
 			mpic: interrupt-controller@20a00 {
 				compatible = "marvell,mpic";
 				#interrupt-cells = <1>;
-				#size-cells = <1>;
 				interrupt-controller;
 				msi-controller;
 			};
diff --git a/arch/arm/boot/dts/armada-370.dtsi b/arch/arm/boot/dts/marvell/armada-370.dtsi
index 46e6d3ed8f35..2013a5ccecd3 100644
--- a/arch/arm/boot/dts/armada-370.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-370.dtsi
@@ -60,34 +60,54 @@
 				reg = <0x0800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 58>;
 				#interrupt-cells = <1>;
                                 ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
                                           0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 58>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie0_intc 0>,
+						<0 0 0 2 &pcie0_intc 1>,
+						<0 0 0 3 &pcie0_intc 2>,
+						<0 0 0 4 &pcie0_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 5>;
 				status = "disabled";
+
+				pcie0_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie2: pcie@2,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
+				assigned-addresses = <0x82001000 0 0x80000 0 0x2000>;
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 62>;
 				#interrupt-cells = <1>;
                                 ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
                                           0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 62>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie2_intc 0>,
+						<0 0 0 2 &pcie2_intc 1>,
+						<0 0 0 3 &pcie2_intc 2>,
+						<0 0 0 4 &pcie2_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 9>;
 				status = "disabled";
+
+				pcie2_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 
diff --git a/arch/arm/boot/dts/armada-375-db.dts b/arch/arm/boot/dts/marvell/armada-375-db.dts
index 0e679465cbb5..4c4092790a20 100644
--- a/arch/arm/boot/dts/armada-375-db.dts
+++ b/arch/arm/boot/dts/marvell/armada-375-db.dts
@@ -64,7 +64,7 @@
 
 	status = "disabled";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "n25q128a13", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-375.dtsi b/arch/arm/boot/dts/marvell/armada-375.dtsi
index 7f2f24a29e6c..99778b4b7e7b 100644
--- a/arch/arm/boot/dts/armada-375.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-375.dtsi
@@ -178,6 +178,8 @@
 
 			/* Network controller */
 			ethernet: ethernet@f0000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				compatible = "marvell,armada-375-pp2";
 				reg = <0xf0000 0xa000>, /* Packet Processor regs */
 				      <0xc0000 0x3060>, /* LMS regs */
@@ -187,15 +189,17 @@
 				clock-names = "pp_clk", "gop_clk";
 				status = "disabled";
 
-				eth0: eth0 {
+				eth0: ethernet-port@0 {
 					interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
-					port-id = <0>;
+					reg = <0>;
+					port-id = <0>; /* For backward compatibility. */
 					status = "disabled";
 				};
 
-				eth1: eth1 {
+				eth1: ethernet-port@1 {
 					interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
-					port-id = <1>;
+					reg = <1>;
+					port-id = <1>; /* For backward compatibility. */
 					status = "disabled";
 				};
 			};
@@ -372,7 +376,6 @@
 				compatible = "marvell,mpic";
 				reg = <0x20a00 0x2d0>, <0x21070 0x58>;
 				#interrupt-cells = <1>;
-				#size-cells = <1>;
 				interrupt-controller;
 				msi-controller;
 				interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>;
@@ -568,34 +571,54 @@
 				reg = <0x0800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie0_intc 0>,
+						<0 0 0 2 &pcie0_intc 1>,
+						<0 0 0 3 &pcie0_intc 2>,
+						<0 0 0 4 &pcie0_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 5>;
 				status = "disabled";
+
+				pcie0_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie1: pcie@2,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				assigned-addresses = <0x82001000 0 0x44000 0 0x2000>;
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
 					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <1>;
 				clocks = <&gateclk 6>;
 				status = "disabled";
+
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 		};
diff --git a/arch/arm/boot/dts/armada-380.dtsi b/arch/arm/boot/dts/marvell/armada-380.dtsi
index cff1269f3fbf..e94f22b0e9b5 100644
--- a/arch/arm/boot/dts/armada-380.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-380.dtsi
@@ -64,54 +64,84 @@
 				reg = <0x0800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 8>;
 				status = "disabled";
+
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			/* x1 port */
 			pcie@2,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+				assigned-addresses = <0x82001000 0 0x40000 0 0x2000>;
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
 					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie2_intc 0>,
+						<0 0 0 2 &pcie2_intc 1>,
+						<0 0 0 3 &pcie2_intc 2>,
+						<0 0 0 4 &pcie2_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 5>;
 				status = "disabled";
+
+				pcie2_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			/* x1 port */
 			pcie@3,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				assigned-addresses = <0x82001800 0 0x44000 0 0x2000>;
 				reg = <0x1800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
 					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie3_intc 0>,
+						<0 0 0 2 &pcie3_intc 1>,
+						<0 0 0 3 &pcie3_intc 2>,
+						<0 0 0 4 &pcie3_intc 3>;
 				marvell,pcie-port = <2>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 6>;
 				status = "disabled";
+
+				pcie3_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/armada-381-netgear-gs110emx.dts b/arch/arm/boot/dts/marvell/armada-381-netgear-gs110emx.dts
index 0a961116a1f9..5baf83e5253d 100644
--- a/arch/arm/boot/dts/armada-381-netgear-gs110emx.dts
+++ b/arch/arm/boot/dts/marvell/armada-381-netgear-gs110emx.dts
@@ -24,7 +24,7 @@
 		pinctrl-0 = <&front_button_pins>;
 		pinctrl-names = "default";
 
-		factory_default {
+		key-factory-default {
 			label = "Factory Default";
 			gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_RESTART>;
@@ -77,51 +77,49 @@
 	pinctrl-0 = <&mdio_pins>;
 	status = "okay";
 
-	switch@0 {
+	ethernet-switch@0 {
 		compatible = "marvell,mv88e6190";
-		#address-cells = <1>;
 		#interrupt-cells = <2>;
 		interrupt-controller;
 		interrupt-parent = <&gpio1>;
 		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
 		pinctrl-0 = <&switch_interrupt_pins>;
 		pinctrl-names = "default";
-		#size-cells = <0>;
 		reg = <0>;
 
 		mdio {
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			switch0phy1: switch0phy1@1 {
+			switch0phy1: ethernet-phy@1 {
 				reg = <0x1>;
 			};
 
-			switch0phy2: switch0phy2@2 {
+			switch0phy2: ethernet-phy@2 {
 				reg = <0x2>;
 			};
 
-			switch0phy3: switch0phy3@3 {
+			switch0phy3: ethernet-phy@3 {
 				reg = <0x3>;
 			};
 
-			switch0phy4: switch0phy4@4 {
+			switch0phy4: ethernet-phy@4 {
 				reg = <0x4>;
 			};
 
-			switch0phy5: switch0phy5@5 {
+			switch0phy5: ethernet-phy@5 {
 				reg = <0x5>;
 			};
 
-			switch0phy6: switch0phy6@6 {
+			switch0phy6: ethernet-phy@6 {
 				reg = <0x6>;
 			};
 
-			switch0phy7: switch0phy7@7 {
+			switch0phy7: ethernet-phy@7 {
 				reg = <0x7>;
 			};
 
-			switch0phy8: switch0phy8@8 {
+			switch0phy8: ethernet-phy@8 {
 				reg = <0x8>;
 			};
 		};
@@ -142,13 +140,13 @@
 			};
 		};
 
-		ports {
+		ethernet-ports {
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			port@0 {
+			ethernet-port@0 {
 				ethernet = <&eth0>;
-				label = "cpu";
+				phy-mode = "rgmii";
 				reg = <0>;
 
 				fixed-link {
@@ -158,55 +156,55 @@
 				};
 			};
 
-			port@1 {
+			ethernet-port@1 {
 				label = "lan1";
 				phy-handle = <&switch0phy1>;
 				reg = <1>;
 			};
 
-			port@2 {
+			ethernet-port@2 {
 				label = "lan2";
 				phy-handle = <&switch0phy2>;
 				reg = <2>;
 			};
 
-			port@3 {
+			ethernet-port@3 {
 				label = "lan3";
 				phy-handle = <&switch0phy3>;
 				reg = <3>;
 			};
 
-			port@4 {
+			ethernet-port@4 {
 				label = "lan4";
 				phy-handle = <&switch0phy4>;
 				reg = <4>;
 			};
 
-			port@5 {
+			ethernet-port@5 {
 				label = "lan5";
 				phy-handle = <&switch0phy5>;
 				reg = <5>;
 			};
 
-			port@6 {
+			ethernet-port@6 {
 				label = "lan6";
 				phy-handle = <&switch0phy6>;
 				reg = <6>;
 			};
 
-			port@7 {
+			ethernet-port@7 {
 				label = "lan7";
 				phy-handle = <&switch0phy7>;
 				reg = <7>;
 			};
 
-			port@8 {
+			ethernet-port@8 {
 				label = "lan8";
 				phy-handle = <&switch0phy8>;
 				reg = <8>;
 			};
 
-			port@9 {
+			ethernet-port@9 {
 				/* 88X3310P external phy */
 				label = "lan9";
 				phy-handle = <&phy1>;
@@ -214,7 +212,7 @@
 				reg = <9>;
 			};
 
-			port@a {
+			ethernet-port@a {
 				/* 88X3310P external phy */
 				label = "lan10";
 				phy-handle = <&phy2>;
@@ -242,7 +240,7 @@
 	pinctrl-names = "default";
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-382-rd-ac3x-48g4x2xl.dts b/arch/arm/boot/dts/marvell/armada-382-rd-ac3x-48g4x2xl.dts
index 584f0d0398a5..6ab65d21861a 100644
--- a/arch/arm/boot/dts/armada-382-rd-ac3x-48g4x2xl.dts
+++ b/arch/arm/boot/dts/marvell/armada-382-rd-ac3x-48g4x2xl.dts
@@ -40,7 +40,7 @@
 	pinctrl-0 = <&i2c0_pins>;
 	status = "okay";
 
-	eeprom@53{
+	eeprom@53 {
 		compatible = "atmel,24c64";
 		reg = <0x53>;
 	};
@@ -95,11 +95,11 @@
 				reg = <0x00000000 0x00500000>;
 				label = "u-boot";
 			};
-			partition@500000{
+			partition@500000 {
 				reg = <0x00500000 0x00400000>;
 				label = "u-boot env";
 			};
-			partition@900000{
+			partition@900000 {
 				reg = <0x00900000 0x3F700000>;
 				label = "user";
 			};
diff --git a/arch/arm/boot/dts/armada-385-atl-x530.dts b/arch/arm/boot/dts/marvell/armada-385-atl-x530.dts
index ed3f41c7df71..2fb7304039be 100644
--- a/arch/arm/boot/dts/armada-385-atl-x530.dts
+++ b/arch/arm/boot/dts/marvell/armada-385-atl-x530.dts
@@ -43,6 +43,17 @@
 			};
 		};
 	};
+
+	led-7seg {
+		compatible = "gpio-7-segment";
+		segment-gpios = <&led_7seg_gpio 0 GPIO_ACTIVE_LOW>,
+				<&led_7seg_gpio 1 GPIO_ACTIVE_LOW>,
+				<&led_7seg_gpio 2 GPIO_ACTIVE_LOW>,
+				<&led_7seg_gpio 3 GPIO_ACTIVE_LOW>,
+				<&led_7seg_gpio 4 GPIO_ACTIVE_LOW>,
+				<&led_7seg_gpio 5 GPIO_ACTIVE_LOW>,
+				<&led_7seg_gpio 6 GPIO_ACTIVE_LOW>;
+	};
 };
 
 &pciec {
@@ -149,7 +160,7 @@
 			#size-cells = <0>;
 			reg = <3>;
 
-			gpio@20 {
+			led_7seg_gpio: gpio@20 {
 				compatible = "nxp,pca9554";
 				gpio-controller;
 				#gpio-cells = <2>;
@@ -168,7 +179,7 @@
 	pinctrl-0 = <&spi1_pins>;
 	status = "okay";
 
-	spi-flash@1 {
+	flash@1 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
@@ -179,19 +190,19 @@
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
 			#size-cells = <1>;
-			partition@u-boot {
+			partition@0 {
 				reg = <0x00000000 0x00100000>;
 				label = "u-boot";
 			};
-			partition@u-boot-env {
+			partition@100000 {
 				reg = <0x00100000 0x00040000>;
 				label = "u-boot-env";
 			};
-			partition@unused {
+			partition@140000 {
 				reg = <0x00140000 0x00e80000>;
 				label = "unused";
 			};
-			partition@idprom {
+			partition@fc0000 {
 				reg = <0x00fc0000 0x00040000>;
 				label = "idprom";
 			};
@@ -216,16 +227,16 @@
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
 			#size-cells = <1>;
-			partition@user {
+			partition@0 {
 				reg = <0x00000000 0x0f000000>;
 				label = "user";
 			};
-			partition@errlog {
+			partition@f000000 {
 				/* Maximum mtdoops size is 8MB, so set to that. */
 				reg = <0x0f000000 0x00800000>;
 				label = "errlog";
 			};
-			partition@nand-bbt {
+			partition@f800000 {
 				reg = <0x0f800000 0x00800000>;
 				label = "nand-bbt";
 			};
diff --git a/arch/arm/boot/dts/armada-385-clearfog-gtr-l8.dts b/arch/arm/boot/dts/marvell/armada-385-clearfog-gtr-l8.dts
index c9ac630e5874..cb85f8e31dfc 100644
--- a/arch/arm/boot/dts/armada-385-clearfog-gtr-l8.dts
+++ b/arch/arm/boot/dts/marvell/armada-385-clearfog-gtr-l8.dts
@@ -4,72 +4,97 @@
 
 / {
 	model = "SolidRun Clearfog GTR L8";
+	compatible = "solidrun,clearfog-gtr-l8", "marvell,armada385",
+		     "marvell,armada380";
+
+	/* CON25 */
+	sfp1: sfp-1 {
+		compatible = "sff,sfp";
+		pinctrl-0 = <&cf_gtr_sfp1_pins>;
+		pinctrl-names = "default";
+		i2c-bus = <&i2c0>;
+		mod-def0-gpio = <&gpio0 24 GPIO_ACTIVE_LOW>;
+		tx-disable-gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+	};
 };
 
 &mdio {
-	switch0: switch0@4 {
+	switch0: ethernet-switch@4 {
 		compatible = "marvell,mv88e6190";
 		reg = <4>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&cf_gtr_switch_reset_pins>;
 		reset-gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
 
-		ports {
+		ethernet-ports {
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			port@1 {
+			ethernet-port@1 {
 				reg = <1>;
-				label = "lan8";
+				label = "lan1";
 				phy-handle = <&switch0phy0>;
 			};
 
-			port@2 {
+			ethernet-port@2 {
 				reg = <2>;
-				label = "lan7";
+				label = "lan2";
 				phy-handle = <&switch0phy1>;
 			};
 
-			port@3 {
+			ethernet-port@3 {
 				reg = <3>;
-				label = "lan6";
+				label = "lan3";
 				phy-handle = <&switch0phy2>;
 			};
 
-			port@4 {
+			ethernet-port@4 {
 				reg = <4>;
-				label = "lan5";
+				label = "lan4";
 				phy-handle = <&switch0phy3>;
 			};
 
-			port@5 {
+			ethernet-port@5 {
 				reg = <5>;
-				label = "lan4";
+				label = "lan5";
 				phy-handle = <&switch0phy4>;
 			};
 
-			port@6 {
+			ethernet-port@6 {
 				reg = <6>;
-				label = "lan3";
+				label = "lan6";
 				phy-handle = <&switch0phy5>;
 			};
 
-			port@7 {
+			ethernet-port@7 {
 				reg = <7>;
-				label = "lan2";
+				label = "lan7";
 				phy-handle = <&switch0phy6>;
 			};
 
-			port@8 {
+			ethernet-port@8 {
 				reg = <8>;
-				label = "lan1";
+				label = "lan8";
 				phy-handle = <&switch0phy7>;
 			};
 
-			port@10 {
+			ethernet-port@9 {
+				reg = <9>;
+				label = "lan-sfp";
+				phy-mode = "sgmii";
+				sfp = <&sfp1>;
+				managed = "in-band-status";
+			};
+
+			ethernet-port@10 {
 				reg = <10>;
-				label = "cpu";
+				phy-mode = "2500base-x";
 				ethernet = <&eth1>;
+
+				fixed-link {
+					speed = <2500>;
+					full-duplex;
+				};
 			};
 
 		};
@@ -78,35 +103,35 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			switch0phy0: switch0phy0@1 {
+			switch0phy0: ethernet-phy@1 {
 				reg = <0x1>;
 			};
 
-			switch0phy1: switch0phy1@2 {
+			switch0phy1: ethernet-phy@2 {
 				reg = <0x2>;
 			};
 
-			switch0phy2: switch0phy2@3 {
+			switch0phy2: ethernet-phy@3 {
 				reg = <0x3>;
 			};
 
-			switch0phy3: switch0phy3@4 {
+			switch0phy3: ethernet-phy@4 {
 				reg = <0x4>;
 			};
 
-			switch0phy4: switch0phy4@5 {
+			switch0phy4: ethernet-phy@5 {
 				reg = <0x5>;
 			};
 
-			switch0phy5: switch0phy5@6 {
+			switch0phy5: ethernet-phy@6 {
 				reg = <0x6>;
 			};
 
-			switch0phy6: switch0phy6@7 {
+			switch0phy6: ethernet-phy@7 {
 				reg = <0x7>;
 			};
 
-			switch0phy7: switch0phy7@8 {
+			switch0phy7: ethernet-phy@8 {
 				reg = <0x8>;
 			};
 		};
diff --git a/arch/arm/boot/dts/armada-385-clearfog-gtr-s4.dts b/arch/arm/boot/dts/marvell/armada-385-clearfog-gtr-s4.dts
index fa653b379490..5f83d981449a 100644
--- a/arch/arm/boot/dts/armada-385-clearfog-gtr-s4.dts
+++ b/arch/arm/boot/dts/marvell/armada-385-clearfog-gtr-s4.dts
@@ -4,6 +4,8 @@
 
 / {
 	model = "SolidRun Clearfog GTR S4";
+	compatible = "solidrun,clearfog-gtr-s4", "marvell,armada385",
+		     "marvell,armada380";
 };
 
 &sfp0 {
@@ -11,45 +13,50 @@
 };
 
 &mdio {
-	switch0: switch0@4 {
+	switch0: ethernet-switch@4 {
 		compatible = "marvell,mv88e6085";
 		reg = <4>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&cf_gtr_switch_reset_pins>;
 		reset-gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
 
-		ports {
+		ethernet-ports {
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			port@1 {
+			ethernet-port@1 {
 				reg = <1>;
 				label = "lan2";
 				phy-handle = <&switch0phy0>;
 			};
 
-			port@2 {
+			ethernet-port@2 {
 				reg = <2>;
 				label = "lan1";
 				phy-handle = <&switch0phy1>;
 			};
 
-			port@3 {
+			ethernet-port@3 {
 				reg = <3>;
 				label = "lan4";
 				phy-handle = <&switch0phy2>;
 			};
 
-			port@4 {
+			ethernet-port@4 {
 				reg = <4>;
 				label = "lan3";
 				phy-handle = <&switch0phy3>;
 			};
 
-			port@5 {
+			ethernet-port@5 {
 				reg = <5>;
-				label = "cpu";
+				phy-mode = "2500base-x";
 				ethernet = <&eth1>;
+
+				fixed-link {
+					speed = <2500>;
+					full-duplex;
+				};
 			};
 
 		};
@@ -58,19 +65,19 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			switch0phy0: switch0phy0@11 {
+			switch0phy0: ethernet-phy@11 {
 				reg = <0x11>;
 			};
 
-			switch0phy1: switch0phy1@12 {
+			switch0phy1: ethernet-phy@12 {
 				reg = <0x12>;
 			};
 
-			switch0phy2: switch0phy2@13 {
+			switch0phy2: ethernet-phy@13 {
 				reg = <0x13>;
 			};
 
-			switch0phy3: switch0phy3@14 {
+			switch0phy3: ethernet-phy@14 {
 				reg = <0x14>;
 			};
 		};
diff --git a/arch/arm/boot/dts/armada-385-clearfog-gtr.dtsi b/arch/arm/boot/dts/marvell/armada-385-clearfog-gtr.dtsi
index 624bbcae68c0..7aa71a9aa1bb 100644
--- a/arch/arm/boot/dts/armada-385-clearfog-gtr.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-385-clearfog-gtr.dtsi
@@ -141,18 +141,13 @@
 			};
 
 			pinctrl@18000 {
-				cf_gtr_switch_reset_pins: cf-gtr-switch-reset-pins {
-					marvell,pins = "mpp18";
-					marvell,function = "gpio";
-				};
-
-				cf_gtr_usb3_con_vbus: cf-gtr-usb3-con-vbus {
-					marvell,pins = "mpp22";
+				cf_gtr_fan_pwm: cf-gtr-fan-pwm {
+					marvell,pins = "mpp23";
 					marvell,function = "gpio";
 				};
 
-				cf_gtr_fan_pwm: cf-gtr-fan-pwm {
-					marvell,pins = "mpp23";
+				cf_gtr_front_button_pins: cf-gtr-front-button-pins {
+					marvell,pins = "mpp53";
 					marvell,function = "gpio";
 				};
 
@@ -162,6 +157,37 @@
 					marvell,function = "i2c1";
 				};
 
+				cf_gtr_isolation_pins: cf-gtr-isolation-pins {
+					marvell,pins = "mpp47";
+					marvell,function = "gpio";
+				};
+
+				cf_gtr_led_pins: led-pins {
+					marvell,pins = "mpp42", "mpp52";
+					marvell,function = "gpio";
+				};
+
+				cf_gtr_lte_disable_pins: lte-disable-pins {
+					marvell,pins = "mpp34";
+					marvell,function = "gpio";
+				};
+
+				cf_gtr_pci_pins: pci-pins {
+					// pci reset
+					marvell,pins = "mpp33", "mpp35", "mpp44";
+					marvell,function = "gpio";
+				};
+
+				cf_gtr_poe_reset_pins: cf-gtr-poe-reset-pins {
+					marvell,pins = "mpp48";
+					marvell,function = "gpio";
+				};
+
+				cf_gtr_rear_button_pins: cf-gtr-rear-button-pins {
+					marvell,pins = "mpp36";
+					marvell,function = "gpio";
+				};
+
 				cf_gtr_sdhci_pins: cf-gtr-sdhci-pins {
 					marvell,pins = "mpp21", "mpp28",
 						       "mpp37", "mpp38",
@@ -169,13 +195,15 @@
 					marvell,function = "sd0";
 				};
 
-				cf_gtr_isolation_pins: cf-gtr-isolation-pins {
-					marvell,pins = "mpp47";
+				cf_gtr_sfp0_pins: sfp0-pins {
+					/* sfp modabs, txdisable */
+					marvell,pins = "mpp25", "mpp46";
 					marvell,function = "gpio";
 				};
 
-				cf_gtr_poe_reset_pins: cf-gtr-poe-reset-pins {
-					marvell,pins = "mpp48";
+				cf_gtr_sfp1_pins: sfp1-pins {
+					/* sfp modabs, txdisable */
+					marvell,pins = "mpp24", "mpp54";
 					marvell,function = "gpio";
 				};
 
@@ -184,13 +212,18 @@
 					marvell,function = "spi1";
 				};
 
-				cf_gtr_front_button_pins: cf-gtr-front-button-pins {
-					marvell,pins = "mpp53";
+				cf_gtr_switch_reset_pins: cf-gtr-switch-reset-pins {
+					marvell,pins = "mpp18";
 					marvell,function = "gpio";
 				};
 
-				cf_gtr_rear_button_pins: cf-gtr-rear-button-pins {
-					marvell,pins = "mpp36";
+				cf_gtr_usb3_con_vbus: cf-gtr-usb3-con-vbus {
+					marvell,pins = "mpp22";
+					marvell,function = "gpio";
+				};
+
+				cf_gtr_wifi_disable_pins: wifi-disable-pins {
+					marvell,pins = "mpp30", "mpp31";
 					marvell,function = "gpio";
 				};
 			};
@@ -221,21 +254,26 @@
 		};
 
 		pcie {
+			pinctrl-0 = <&cf_gtr_pci_pins>;
+			pinctrl-names = "default";
 			status = "okay";
 			/*
 			 * The PCIe units are accessible through
 			 * the mini-PCIe connectors on the board.
 			 */
+			/* CON3 - serdes 0 */
 			pcie@1,0 {
 				reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
 				status = "okay";
 			};
 
+			/* CON4 - serdes 2 */
 			pcie@2,0 {
 				reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
 				status = "okay";
 			};
 
+			/* CON2 - serdes 4 */
 			pcie@3,0 {
 				reset-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
 				status = "okay";
@@ -243,10 +281,12 @@
 		};
 	};
 
-	sfp0: sfp {
+	/* CON5 */
+	sfp0: sfp-0 {
 		compatible = "sff,sfp";
+		pinctrl-0 = <&cf_gtr_sfp0_pins>;
+		pinctrl-names = "default";
 		i2c-bus = <&i2c1>;
-		los-gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
 		mod-def0-gpio = <&gpio0 25 GPIO_ACTIVE_LOW>;
 		tx-disable-gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
 	};
@@ -256,14 +296,14 @@
 		pinctrl-0 = <&cf_gtr_rear_button_pins &cf_gtr_front_button_pins>;
 		pinctrl-names = "default";
 
-		button_0 {
+		button-0 {
 			label = "Rear Button";
 			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
 			linux,can-disable;
 			linux,code = <BTN_0>;
 		};
 
-		button_1 {
+		button-1 {
 			label = "Front Button";
 			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
 			linux,can-disable;
@@ -273,6 +313,8 @@
 
 	gpio-leds {
 		compatible = "gpio-leds";
+		pinctrl-0 = <&cf_gtr_led_pins>;
+		pinctrl-names = "default";
 
 		led1 {
 			function = LED_FUNCTION_CPU;
@@ -365,7 +407,7 @@
 	pinctrl-names = "default";
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "w25q32", "jedec,spi-nor";
@@ -381,14 +423,14 @@
 	status = "okay";
 
 	/* U26 temperature sensor placed near SoC */
-	temp1: nct75@4c {
-		compatible = "lm75";
+	temp1: temperature-sensor@4c {
+		compatible = "ti,tmp75c";
 		reg = <0x4c>;
 	};
 
 	/* U27 temperature sensor placed near RTC battery */
-	temp2: nct75@4d {
-		compatible = "lm75";
+	temp2: temperature-sensor@4d {
+		compatible = "ti,tmp75c";
 		reg = <0x4d>;
 	};
 
@@ -408,10 +450,10 @@
 };
 
 &gpio0 {
-	pinctrl-0 = <&cf_gtr_fan_pwm>;
+	pinctrl-0 = <&cf_gtr_fan_pwm &cf_gtr_wifi_disable_pins>;
 	pinctrl-names = "default";
 
-	wifi-disable {
+	wifi-disable-hog {
 		gpio-hog;
 		gpios = <30 GPIO_ACTIVE_LOW>, <31 GPIO_ACTIVE_LOW>;
 		output-low;
@@ -420,10 +462,10 @@
 };
 
 &gpio1 {
-	pinctrl-0 = <&cf_gtr_isolation_pins &cf_gtr_poe_reset_pins>;
+	pinctrl-0 = <&cf_gtr_isolation_pins &cf_gtr_poe_reset_pins &cf_gtr_lte_disable_pins>;
 	pinctrl-names = "default";
 
-	lte-disable {
+	lte-disable-hog {
 		gpio-hog;
 		gpios = <2 GPIO_ACTIVE_LOW>;
 		output-low;
@@ -434,14 +476,14 @@
 	 * This signal, when asserted, isolates Armada 38x sample at reset pins
 	 * from control of external devices. Should be de-asserted after reset.
 	 */
-	sar-isolation {
+	sar-isolation-hog {
 		gpio-hog;
 		gpios = <15 GPIO_ACTIVE_LOW>;
 		output-low;
 		line-name = "sar-isolation";
 	};
 
-	poe-reset {
+	poe-reset-hog {
 		gpio-hog;
 		gpios = <16 GPIO_ACTIVE_LOW>;
 		output-low;
diff --git a/arch/arm/boot/dts/armada-385-db-88f6820-amc.dts b/arch/arm/boot/dts/marvell/armada-385-db-88f6820-amc.dts
index 7881df3b28a0..389d9c75d546 100644
--- a/arch/arm/boot/dts/armada-385-db-88f6820-amc.dts
+++ b/arch/arm/boot/dts/marvell/armada-385-db-88f6820-amc.dts
@@ -126,7 +126,7 @@
 	pinctrl-0 = <&spi1_pins>;
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-385-db-ap.dts b/arch/arm/boot/dts/marvell/armada-385-db-ap.dts
index 0e4613bb56ee..332f8fce77dc 100644
--- a/arch/arm/boot/dts/armada-385-db-ap.dts
+++ b/arch/arm/boot/dts/marvell/armada-385-db-ap.dts
@@ -192,7 +192,7 @@
 	pinctrl-0 = <&spi1_pins>;
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p128", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-385-linksys-caiman.dts b/arch/arm/boot/dts/marvell/armada-385-linksys-caiman.dts
index a03050c97084..88b2921fed55 100644
--- a/arch/arm/boot/dts/armada-385-linksys-caiman.dts
+++ b/arch/arm/boot/dts/marvell/armada-385-linksys-caiman.dts
@@ -62,11 +62,11 @@
 };
 
 &gpio_leds {
-	power {
+	led-power {
 		label = "caiman:white:power";
 	};
 
-	sata {
+	led-sata {
 		label = "caiman:white:sata";
 	};
 };
diff --git a/arch/arm/boot/dts/armada-385-linksys-cobra.dts b/arch/arm/boot/dts/marvell/armada-385-linksys-cobra.dts
index e3e4877a6f49..88200f930d0d 100644
--- a/arch/arm/boot/dts/armada-385-linksys-cobra.dts
+++ b/arch/arm/boot/dts/marvell/armada-385-linksys-cobra.dts
@@ -62,11 +62,11 @@
 };
 
 &gpio_leds {
-	power {
+	led-power {
 		label = "cobra:white:power";
 	};
 
-	sata {
+	led-sata {
 		label = "cobra:white:sata";
 	};
 };
diff --git a/arch/arm/boot/dts/armada-385-linksys-rango.dts b/arch/arm/boot/dts/marvell/armada-385-linksys-rango.dts
index 3c4af57ec2b9..4ab45f294de2 100644
--- a/arch/arm/boot/dts/armada-385-linksys-rango.dts
+++ b/arch/arm/boot/dts/marvell/armada-385-linksys-rango.dts
@@ -54,22 +54,22 @@
 };
 
 &gpio_leds {
-	power {
+	led-power {
 		gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>;
 		label = "rango:white:power";
 	};
 
-	sata {
+	led-sata {
 		gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
 		label = "rango:white:sata";
 	};
 
-	wlan_2g {
+	led-wlan_2g {
 		gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
 		label = "rango:white:wlan_2g";
 	};
 
-	wlan_5g {
+	led-wlan_5g {
 		gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
 		label = "rango:white:wlan_5g";
 	};
diff --git a/arch/arm/boot/dts/armada-385-linksys-shelby.dts b/arch/arm/boot/dts/marvell/armada-385-linksys-shelby.dts
index 3451cd3e5dff..f1b1f22413f1 100644
--- a/arch/arm/boot/dts/armada-385-linksys-shelby.dts
+++ b/arch/arm/boot/dts/marvell/armada-385-linksys-shelby.dts
@@ -62,11 +62,11 @@
 };
 
 &gpio_leds {
-	power {
+	led-power {
 		label = "shelby:white:power";
 	};
 
-	sata {
+	led-sata {
 		label = "shelby:white:sata";
 	};
 };
diff --git a/arch/arm/boot/dts/armada-385-linksys.dtsi b/arch/arm/boot/dts/marvell/armada-385-linksys.dtsi
index fb9c8a0b241c..4116ed60f709 100644
--- a/arch/arm/boot/dts/armada-385-linksys.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-385-linksys.dtsi
@@ -53,13 +53,13 @@
 		pinctrl-0 = <&gpio_keys_pins>;
 		pinctrl-names = "default";
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
 		};
 
-		reset {
+		button-reset {
 			label = "Factory Reset Button";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
@@ -71,12 +71,12 @@
 		pinctrl-0 = <&gpio_leds_pins>;
 		pinctrl-names = "default";
 
-		power {
+		led-power {
 			gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 		};
 
-		sata {
+		led-sata {
 			gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 			linux,default-trigger = "disk-activity";
@@ -158,44 +158,42 @@
 &mdio {
 	status = "okay";
 
-	switch@0 {
+	ethernet-switch@0 {
 		compatible = "marvell,mv88e6085";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		reg = <0>;
 
-		ports {
+		ethernet-ports {
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			port@0 {
+			ethernet-port@0 {
 				reg = <0>;
 				label = "lan4";
 			};
 
-			port@1 {
+			ethernet-port@1 {
 				reg = <1>;
 				label = "lan3";
 			};
 
-			port@2 {
+			ethernet-port@2 {
 				reg = <2>;
 				label = "lan2";
 			};
 
-			port@3 {
+			ethernet-port@3 {
 				reg = <3>;
 				label = "lan1";
 			};
 
-			port@4 {
+			ethernet-port@4 {
 				reg = <4>;
 				label = "wan";
 			};
 
-			port@5 {
+			ethernet-port@5 {
 				reg = <5>;
-				label = "cpu";
+				phy-mode = "sgmii";
 				ethernet = <&eth2>;
 
 				fixed-link {
diff --git a/arch/arm/boot/dts/armada-385-synology-ds116.dts b/arch/arm/boot/dts/marvell/armada-385-synology-ds116.dts
index d8769956cbfc..6caa5c50175a 100644
--- a/arch/arm/boot/dts/armada-385-synology-ds116.dts
+++ b/arch/arm/boot/dts/marvell/armada-385-synology-ds116.dts
@@ -131,14 +131,14 @@
 			gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>,
 				<&gpio1 17 GPIO_ACTIVE_HIGH>,
 				<&gpio1 16 GPIO_ACTIVE_HIGH>;
-			gpio-fan,speed-map = <   0 0
-					      1500 1
-					      2500 2
-					      3000 3
-					      3400 4
-					      3700 5
-					      3900 6
-					      4000 7>;
+			gpio-fan,speed-map = <   0 0>,
+					     <1500 1>,
+					     <2500 2>,
+					     <3000 3>,
+					     <3400 4>,
+					     <3700 5>,
+					     <3900 6>,
+					     <4000 7>;
 			#cooling-cells = <2>;
 		};
 
@@ -149,7 +149,7 @@
 			 * sata0, and accesses to SATA disk 0 make it blink so it
 			 * doesn't need to be declared here.
 			 */
-			orange {
+			led-orange {
 				gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
 				label = "ds116:orange:disk";
 				default-state = "off";
@@ -223,7 +223,7 @@
 	pinctrl-0 = <&spi0_pins>;
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "macronix,mx25l6405d", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-385-turris-omnia.dts b/arch/arm/boot/dts/marvell/armada-385-turris-omnia.dts
index f240018148f6..83fe00abd652 100644
--- a/arch/arm/boot/dts/armada-385-turris-omnia.dts
+++ b/arch/arm/boot/dts/marvell/armada-385-turris-omnia.dts
@@ -23,6 +23,12 @@
 		stdout-path = &uart0;
 	};
 
+	aliases {
+		ethernet0 = &eth0;
+		ethernet1 = &eth1;
+		ethernet2 = &eth2;
+	};
+
 	memory {
 		device_type = "memory";
 		reg = <0x00000000 0x40000000>; /* 1024 MB */
@@ -105,6 +111,46 @@
 		 */
 		status = "disabled";
 	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		front-button {
+			label = "Front Button";
+			linux,code = <KEY_VENDOR>;
+			linux,can-disable;
+			gpios = <&mcu 0 12 GPIO_ACTIVE_HIGH>;
+			/* debouncing is done by the microcontroller */
+			debounce-interval = <0>;
+		};
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "SPDIF";
+		simple-audio-card,format = "i2s";
+
+		simple-audio-card,cpu {
+			sound-dai = <&audio_controller 1>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&spdif_out>;
+		};
+	};
+
+	spdif_out: spdif-out {
+		#sound-dai-cells = <0>;
+		compatible = "linux,spdif-dit";
+	};
+};
+
+&audio_controller {
+	/* Pin header U16, GPIO51 in SPDIFO mode */
+	pinctrl-0 = <&spdif_pins>;
+	pinctrl-names = "default";
+	spdif-mode;
+	status = "okay";
 };
 
 &bm {
@@ -166,6 +212,7 @@
 	buffer-manager = <&bm>;
 	bm,pool-long = <2>;
 	bm,pool-short = <3>;
+	label = "wan";
 };
 
 &i2c0 {
@@ -184,22 +231,36 @@
 			#size-cells = <0>;
 			reg = <0>;
 
-			/* STM32F0 command interface at address 0x2a */
+			mcu: system-controller@2a {
+				compatible = "cznic,turris-omnia-mcu";
+				reg = <0x2a>;
+
+				pinctrl-names = "default";
+				pinctrl-0 = <&mcu_pins>;
+
+				interrupt-parent = <&gpio1>;
+				interrupts = <11 IRQ_TYPE_NONE>;
+
+				gpio-controller;
+				#gpio-cells = <3>;
+
+				interrupt-controller;
+				#interrupt-cells = <2>;
+			};
 
 			led-controller@2b {
 				compatible = "cznic,turris-omnia-leds";
 				reg = <0x2b>;
+				interrupts-extended = <&mcu 11 IRQ_TYPE_NONE>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				status = "okay";
 
 				/*
 				 * LEDs are controlled by MCU (STM32F0) at
 				 * address 0x2b.
 				 *
-				 * The driver does not support HW control mode
-				 * for the LEDs yet. Disable the LEDs for now.
-				 *
-				 * Also LED functions are not stable yet:
+				 * LED functions are not stable yet:
 				 * - there are 3 LEDs connected via MCU to PCIe
 				 *   ports. One of these ports supports mSATA.
 				 *   There is no mSATA nor PCIe function.
@@ -210,7 +271,6 @@
 				 *   B. Again there is no such function defined.
 				 *   For now we use LED_FUNCTION_INDICATOR
 				 */
-				status = "disabled";
 
 				multi-led@0 {
 					reg = <0x0>;
@@ -348,7 +408,11 @@
 			#size-cells = <0>;
 			reg = <5>;
 
-			/* ATSHA204A at address 0x64 */
+			/* ATSHA204A-MAHDA-T crypto module */
+			crypto@64 {
+				compatible = "atmel,atsha204a";
+				reg = <0x64>;
+			};
 		};
 
 		i2c@6 {
@@ -393,18 +457,17 @@
 	phy1: ethernet-phy@1 {
 		compatible = "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
-		marvell,reg-init = <3 18 0 0x4985>;
+		marvell,reg-init = <3 18 0 0x4985>,
+				   <3 16 0xfff0 0x0001>;
 
 		/* irq is connected to &pcawan pin 7 */
 	};
 
 	/* Switch MV88E6176 at address 0x10 */
-	switch@10 {
+	ethernet-switch@10 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&swint_pins>;
 		compatible = "marvell,mv88e6085";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
 		dsa,member = <0 0>;
 		reg = <0x10>;
@@ -412,38 +475,37 @@
 		interrupt-parent = <&gpio1>;
 		interrupts = <13 IRQ_TYPE_LEVEL_LOW>;
 
-		ports {
+		ethernet-ports {
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			ports@0 {
+			ethernet-port@0 {
 				reg = <0>;
 				label = "lan0";
 			};
 
-			ports@1 {
+			ethernet-port@1 {
 				reg = <1>;
 				label = "lan1";
 			};
 
-			ports@2 {
+			ethernet-port@2 {
 				reg = <2>;
 				label = "lan2";
 			};
 
-			ports@3 {
+			ethernet-port@3 {
 				reg = <3>;
 				label = "lan3";
 			};
 
-			ports@4 {
+			ethernet-port@4 {
 				reg = <4>;
 				label = "lan4";
 			};
 
-			ports@5 {
+			ethernet-port@5 {
 				reg = <5>;
-				label = "cpu";
 				ethernet = <&eth1>;
 				phy-mode = "rgmii-id";
 
@@ -453,12 +515,26 @@
 				};
 			};
 
-			/* port 6 is connected to eth0 */
+			ethernet-port@6 {
+				reg = <6>;
+				ethernet = <&eth0>;
+				phy-mode = "rgmii-id";
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
 		};
 	};
 };
 
 &pinctrl {
+	mcu_pins: mcu-pins {
+		marvell,pins = "mpp43";
+		marvell,function = "gpio";
+	};
+
 	pcawan_pins: pcawan-pins {
 		marvell,pins = "mpp46";
 		marvell,function = "gpio";
@@ -474,7 +550,7 @@
 		marvell,function = "spi0";
 	};
 
-	spi0cs1_pins: spi0cs1-pins {
+	spi0cs2_pins: spi0cs2-pins {
 		marvell,pins = "mpp26";
 		marvell,function = "spi0";
 	};
@@ -485,7 +561,7 @@
 	pinctrl-0 = <&spi0_pins &spi0cs0_pins>;
 	status = "okay";
 
-	spi-nor@0 {
+	flash@0 {
 		compatible = "spansion,s25fl164k", "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -509,7 +585,7 @@
 		};
 	};
 
-	/* MISO, MOSI, SCLK and CS1 are routed to pin header CN11 */
+	/* MISO, MOSI, SCLK and CS2 are routed to pin header CN11 */
 };
 
 &uart0 {
diff --git a/arch/arm/boot/dts/armada-385.dtsi b/arch/arm/boot/dts/marvell/armada-385.dtsi
index 83392b92dae2..be8d607c59b2 100644
--- a/arch/arm/boot/dts/armada-385.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-385.dtsi
@@ -93,7 +93,7 @@
 			/* x1 port */
 			pcie2: pcie@2,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+				assigned-addresses = <0x82001000 0 0x40000 0 0x2000>;
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
@@ -121,7 +121,7 @@
 			/* x1 port */
 			pcie3: pcie@3,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				assigned-addresses = <0x82001800 0 0x44000 0 0x2000>;
 				reg = <0x1800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
@@ -152,7 +152,7 @@
 			 */
 			pcie4: pcie@4,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+				assigned-addresses = <0x82002000 0 0x48000 0 0x2000>;
 				reg = <0x2000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
diff --git a/arch/arm/boot/dts/armada-388-clearfog-base.dts b/arch/arm/boot/dts/marvell/armada-388-clearfog-base.dts
index 53b4bd35522a..cf32ba9b4e8e 100644
--- a/arch/arm/boot/dts/armada-388-clearfog-base.dts
+++ b/arch/arm/boot/dts/marvell/armada-388-clearfog-base.dts
@@ -19,7 +19,7 @@
 		pinctrl-0 = <&rear_button_pins>;
 		pinctrl-names = "default";
 
-		button_0 {
+		button-0 {
 			/* The rear SW3 button */
 			label = "Rear Button";
 			gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
@@ -34,7 +34,7 @@
 };
 
 &gpio0 {
-	phy1_reset {
+	phy1-reset-hog {
 		gpio-hog;
 		gpios = <19 GPIO_ACTIVE_LOW>;
 		output-low;
diff --git a/arch/arm/boot/dts/armada-388-clearfog-pro.dts b/arch/arm/boot/dts/marvell/armada-388-clearfog-pro.dts
index ff890c09c3ed..ff890c09c3ed 100644
--- a/arch/arm/boot/dts/armada-388-clearfog-pro.dts
+++ b/arch/arm/boot/dts/marvell/armada-388-clearfog-pro.dts
diff --git a/arch/arm/boot/dts/armada-388-clearfog.dts b/arch/arm/boot/dts/marvell/armada-388-clearfog.dts
index 4140a5303b48..09bf2e6d4ed0 100644
--- a/arch/arm/boot/dts/armada-388-clearfog.dts
+++ b/arch/arm/boot/dts/marvell/armada-388-clearfog.dts
@@ -10,8 +10,9 @@
 
 / {
 	model = "SolidRun Clearfog A1";
-	compatible = "solidrun,clearfog-a1", "marvell,armada388",
-		"marvell,armada385", "marvell,armada380";
+	compatible = "solidrun,clearfog-pro-a1", "solidrun,clearfog-a1",
+		     "marvell,armada388", "marvell,armada385",
+		     "marvell,armada380";
 
 	soc {
 		internal-regs {
@@ -35,7 +36,7 @@
 		pinctrl-0 = <&rear_button_pins>;
 		pinctrl-names = "default";
 
-		button_0 {
+		button-0 {
 			/* The rear SW3 button */
 			label = "Rear Button";
 			gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
@@ -47,6 +48,8 @@
 
 &eth1 {
 	/* ethernet@30000 */
+	phy-mode = "1000base-x";
+
 	fixed-link {
 		speed = <1000>;
 		full-duplex;
@@ -90,57 +93,58 @@
 &mdio {
 	status = "okay";
 
-	switch@4 {
+	ethernet-switch@4 {
 		compatible = "marvell,mv88e6085";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		reg = <4>;
 		pinctrl-0 = <&clearfog_dsa0_clk_pins &clearfog_dsa0_pins>;
 		pinctrl-names = "default";
 
-		ports {
+		ethernet-ports {
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			port@0 {
+			ethernet-port@0 {
 				reg = <0>;
 				label = "lan5";
 			};
 
-			port@1 {
+			ethernet-port@1 {
 				reg = <1>;
 				label = "lan4";
 			};
 
-			port@2 {
+			ethernet-port@2 {
 				reg = <2>;
 				label = "lan3";
 			};
 
-			port@3 {
+			ethernet-port@3 {
 				reg = <3>;
 				label = "lan2";
 			};
 
-			port@4 {
+			ethernet-port@4 {
 				reg = <4>;
 				label = "lan1";
 			};
 
-			port@5 {
+			ethernet-port@5 {
 				reg = <5>;
-				label = "cpu";
 				ethernet = <&eth1>;
+				phy-mode = "1000base-x";
+
 				fixed-link {
 					speed = <1000>;
 					full-duplex;
 				};
 			};
 
-			port@6 {
+			ethernet-port@6 {
 				/* 88E1512 external phy */
 				reg = <6>;
 				label = "lan6";
+				phy-mode = "rgmii-id";
+
 				fixed-link {
 					speed = <1000>;
 					full-duplex;
diff --git a/arch/arm/boot/dts/armada-388-clearfog.dtsi b/arch/arm/boot/dts/marvell/armada-388-clearfog.dtsi
index f8a06ae4a3c9..f8a06ae4a3c9 100644
--- a/arch/arm/boot/dts/armada-388-clearfog.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-388-clearfog.dtsi
diff --git a/arch/arm/boot/dts/armada-388-db.dts b/arch/arm/boot/dts/marvell/armada-388-db.dts
index a2bec07bf4c5..45cc784659fd 100644
--- a/arch/arm/boot/dts/armada-388-db.dts
+++ b/arch/arm/boot/dts/marvell/armada-388-db.dts
@@ -36,6 +36,11 @@
 			i2c@11000 {
 				status = "okay";
 				clock-frequency = <100000>;
+				audio_codec: audio-codec@4a {
+					#sound-dai-cells = <0>;
+					compatible = "cirrus,cs42l51";
+					reg = <0x4a>;
+				};
 			};
 
 			i2c@11100 {
@@ -57,7 +62,7 @@
 			};
 
 			usb@58000 {
-				status = "ok";
+				status = "okay";
 			};
 
 			ethernet@70000 {
@@ -99,6 +104,12 @@
 				no-1-8-v;
 			};
 
+			audio-controller@e8000 {
+				pinctrl-0 = <&i2s_pins>;
+				pinctrl-names = "default";
+				status = "disabled";
+			};
+
 			usb3@f0000 {
 				status = "okay";
 			};
@@ -128,12 +139,70 @@
 			};
 		};
 	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "Armada 385 DB Audio";
+		simple-audio-card,mclk-fs = <256>;
+		simple-audio-card,widgets =
+			"Headphone", "Out Jack",
+			"Line", "In Jack";
+		simple-audio-card,routing =
+			"Out Jack", "HPL",
+			"Out Jack", "HPR",
+			"AIN1L", "In Jack",
+			"AIN1R", "In Jack";
+		status = "disabled";
+
+		simple-audio-card,dai-link@0 {
+			format = "i2s";
+			cpu {
+				sound-dai = <&audio_controller 0>;
+			};
+
+			codec {
+				sound-dai = <&audio_codec>;
+			};
+		};
+
+		simple-audio-card,dai-link@1 {
+			format = "i2s";
+			cpu {
+				sound-dai = <&audio_controller 1>;
+			};
+
+			codec {
+				sound-dai = <&spdif_out>;
+			};
+		};
+
+		simple-audio-card,dai-link@2 {
+			format = "i2s";
+			cpu {
+				sound-dai = <&audio_controller 1>;
+			};
+
+			codec {
+				sound-dai = <&spdif_in>;
+			};
+		};
+	};
+
+	spdif_out: spdif-out {
+		#sound-dai-cells = <0>;
+		compatible = "linux,spdif-dit";
+	};
+
+	spdif_in: spdif-in {
+		#sound-dai-cells = <0>;
+		compatible = "linux,spdif-dir";
+	};
 };
 
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "w25q32", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-388-gp.dts b/arch/arm/boot/dts/marvell/armada-388-gp.dts
index 9d873257ac45..1de0a172aa5f 100644
--- a/arch/arm/boot/dts/armada-388-gp.dts
+++ b/arch/arm/boot/dts/marvell/armada-388-gp.dts
@@ -237,8 +237,8 @@
 		gpio-fan {
 			compatible = "gpio-fan";
 			gpios = <&expander1 3 GPIO_ACTIVE_HIGH>;
-			gpio-fan,speed-map = <	 0 0
-					      3000 1>;
+			gpio-fan,speed-map = <	 0 0>,
+					     <3000 1>;
 		};
 	};
 
@@ -395,7 +395,7 @@
 	pinctrl-0 = <&spi0_pins>;
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p128", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-388-helios4.dts b/arch/arm/boot/dts/marvell/armada-388-helios4.dts
index ec134e22bae3..ec134e22bae3 100644
--- a/arch/arm/boot/dts/armada-388-helios4.dts
+++ b/arch/arm/boot/dts/marvell/armada-388-helios4.dts
diff --git a/arch/arm/boot/dts/armada-388-rd.dts b/arch/arm/boot/dts/marvell/armada-388-rd.dts
index 328a4d6afd2c..c0efafd45b33 100644
--- a/arch/arm/boot/dts/armada-388-rd.dts
+++ b/arch/arm/boot/dts/marvell/armada-388-rd.dts
@@ -97,7 +97,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p128", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-388.dtsi b/arch/arm/boot/dts/marvell/armada-388.dtsi
index f3a020ff577e..f3a020ff577e 100644
--- a/arch/arm/boot/dts/armada-388.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-388.dtsi
diff --git a/arch/arm/boot/dts/armada-38x-solidrun-microsom.dtsi b/arch/arm/boot/dts/marvell/armada-38x-solidrun-microsom.dtsi
index 363ac4238859..2c64bc6e5a17 100644
--- a/arch/arm/boot/dts/armada-38x-solidrun-microsom.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-38x-solidrun-microsom.dtsi
@@ -101,7 +101,7 @@
 	/* The microsom has an optional W25Q32 on board, connected to CS0 */
 	pinctrl-0 = <&spi1_pins>;
 
-	w25q32: spi-flash@0 {
+	w25q32: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "w25q32", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-38x.dtsi b/arch/arm/boot/dts/marvell/armada-38x.dtsi
index df3c8d1d8f64..1181b13deabc 100644
--- a/arch/arm/boot/dts/armada-38x.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-38x.dtsi
@@ -289,6 +289,18 @@
 					marvell,pins = "mpp44";
 					marvell,function = "sata3";
 				};
+
+				i2s_pins: i2s-pins {
+					marvell,pins = "mpp48", "mpp49",
+						       "mpp50", "mpp51",
+						       "mpp52", "mpp53";
+					marvell,function = "audio";
+				};
+
+				spdif_pins: spdif-pins {
+					marvell,pins = "mpp51";
+					marvell,function = "audio";
+				};
 			};
 
 			gpio0: gpio@18100 {
@@ -298,6 +310,7 @@
 				reg-names = "gpio", "pwm";
 				ngpios = <32>;
 				gpio-controller;
+				gpio-ranges = <&pinctrl 0 0 32>;
 				#gpio-cells = <2>;
 				#pwm-cells = <2>;
 				interrupt-controller;
@@ -316,6 +329,7 @@
 				reg-names = "gpio", "pwm";
 				ngpios = <28>;
 				gpio-controller;
+				gpio-ranges = <&pinctrl 0 32 28>;
 				#gpio-cells = <2>;
 				#pwm-cells = <2>;
 				interrupt-controller;
@@ -394,7 +408,6 @@
 				compatible = "marvell,mpic";
 				reg = <0x20a00 0x2d0>, <0x21070 0x58>;
 				#interrupt-cells = <1>;
-				#size-cells = <1>;
 				interrupt-controller;
 				msi-controller;
 				interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>;
@@ -618,6 +631,18 @@
 				status = "disabled";
 			};
 
+			audio_controller: audio-controller@e8000 {
+				#sound-dai-cells = <1>;
+				compatible = "marvell,armada-380-audio";
+				reg = <0xe8000 0x4000>, <0x18410 0xc>,
+				      <0x18204 0x4>;
+				reg-names = "i2s_regs", "pll_regs", "soc_ctrl";
+				interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gateclk 0>;
+				clock-names = "internal";
+				status = "disabled";
+			};
+
 			usb3_0: usb3@f0000 {
 				compatible = "marvell,armada-380-xhci";
 				reg = <0xf0000 0x4000>,<0xf4000 0x4000>;
diff --git a/arch/arm/boot/dts/armada-390-db.dts b/arch/arm/boot/dts/marvell/armada-390-db.dts
index 0e29474ae9a2..20f518dbac97 100644
--- a/arch/arm/boot/dts/armada-390-db.dts
+++ b/arch/arm/boot/dts/marvell/armada-390-db.dts
@@ -81,7 +81,7 @@
 	pinctrl-0 = <&spi1_pins>;
 	pinctrl-names = "default";
 
-	spi-flash@1 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "n25q128a13",
diff --git a/arch/arm/boot/dts/armada-390.dtsi b/arch/arm/boot/dts/marvell/armada-390.dtsi
index aa2057d4d6f8..aa2057d4d6f8 100644
--- a/arch/arm/boot/dts/armada-390.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-390.dtsi
diff --git a/arch/arm/boot/dts/armada-395-gp.dts b/arch/arm/boot/dts/marvell/armada-395-gp.dts
index 6dd9e9077f84..6dd9e9077f84 100644
--- a/arch/arm/boot/dts/armada-395-gp.dts
+++ b/arch/arm/boot/dts/marvell/armada-395-gp.dts
diff --git a/arch/arm/boot/dts/armada-395.dtsi b/arch/arm/boot/dts/marvell/armada-395.dtsi
index e18a7d9cd7d4..e18a7d9cd7d4 100644
--- a/arch/arm/boot/dts/armada-395.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-395.dtsi
diff --git a/arch/arm/boot/dts/armada-398-db.dts b/arch/arm/boot/dts/marvell/armada-398-db.dts
index fc28308e5bc5..ec6cdbeedde7 100644
--- a/arch/arm/boot/dts/armada-398-db.dts
+++ b/arch/arm/boot/dts/marvell/armada-398-db.dts
@@ -79,7 +79,7 @@
 	pinctrl-0 = <&spi1_pins>;
 	pinctrl-names = "default";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "n25q128a13", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-398.dtsi b/arch/arm/boot/dts/marvell/armada-398.dtsi
index c5ac89399ce1..c5ac89399ce1 100644
--- a/arch/arm/boot/dts/armada-398.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-398.dtsi
diff --git a/arch/arm/boot/dts/armada-39x.dtsi b/arch/arm/boot/dts/marvell/armada-39x.dtsi
index e0b7c2099831..6d05835efb42 100644
--- a/arch/arm/boot/dts/armada-39x.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-39x.dtsi
@@ -268,7 +268,6 @@
 				compatible = "marvell,mpic";
 				reg = <0x20a00 0x2d0>, <0x21070 0x58>;
 				#interrupt-cells = <1>;
-				#size-cells = <1>;
 				interrupt-controller;
 				msi-controller;
 				interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>;
@@ -438,54 +437,84 @@
 				reg = <0x0800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 8>;
 				status = "disabled";
+
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			/* x1 port */
 			pcie@2,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+				assigned-addresses = <0x82001000 0 0x40000 0 0x2000>;
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
 					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie2_intc 0>,
+						<0 0 0 2 &pcie2_intc 1>,
+						<0 0 0 3 &pcie2_intc 2>,
+						<0 0 0 4 &pcie2_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 5>;
 				status = "disabled";
+
+				pcie2_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			/* x1 port */
 			pcie@3,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				assigned-addresses = <0x82001800 0 0x44000 0 0x2000>;
 				reg = <0x1800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
 					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie3_intc 0>,
+						<0 0 0 2 &pcie3_intc 1>,
+						<0 0 0 3 &pcie3_intc 2>,
+						<0 0 0 4 &pcie3_intc 3>;
 				marvell,pcie-port = <2>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 6>;
 				status = "disabled";
+
+				pcie3_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			/*
@@ -494,20 +523,30 @@
 			 */
 			pcie@4,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+				assigned-addresses = <0x82002000 0 0x48000 0 0x2000>;
 				reg = <0x2000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
 					  0x81000000 0 0 0x81000000 0x4 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie4_intc 0>,
+						<0 0 0 2 &pcie4_intc 1>,
+						<0 0 0 3 &pcie4_intc 2>,
+						<0 0 0 4 &pcie4_intc 3>;
 				marvell,pcie-port = <3>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 7>;
 				status = "disabled";
+
+				pcie4_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 
diff --git a/arch/arm/boot/dts/armada-xp-98dx3236.dtsi b/arch/arm/boot/dts/marvell/armada-xp-98dx3236.dtsi
index 38a052a0312d..7a7e2066c498 100644
--- a/arch/arm/boot/dts/armada-xp-98dx3236.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-xp-98dx3236.dtsi
@@ -76,16 +76,26 @@
 				reg = <0x0800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 58>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 58>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 5>;
 				status = "disabled";
+
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 
@@ -286,6 +296,7 @@
 	compatible = "marvell,armada-xp-wdt";
 	clocks = <&coreclk 2>, <&refclk>;
 	clock-names = "nbclk", "fixed";
+	interrupts = <93>, <38>;
 };
 
 &cpurst {
diff --git a/arch/arm/boot/dts/armada-xp-98dx3336.dtsi b/arch/arm/boot/dts/marvell/armada-xp-98dx3336.dtsi
index 1d9d8a8ea60c..1d9d8a8ea60c 100644
--- a/arch/arm/boot/dts/armada-xp-98dx3336.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-xp-98dx3336.dtsi
diff --git a/arch/arm/boot/dts/armada-xp-98dx4251.dtsi b/arch/arm/boot/dts/marvell/armada-xp-98dx4251.dtsi
index 48ffdc72bfc7..48ffdc72bfc7 100644
--- a/arch/arm/boot/dts/armada-xp-98dx4251.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-xp-98dx4251.dtsi
diff --git a/arch/arm/boot/dts/armada-xp-axpwifiap.dts b/arch/arm/boot/dts/marvell/armada-xp-axpwifiap.dts
index 606fd3476a59..5a74197be0ad 100644
--- a/arch/arm/boot/dts/armada-xp-axpwifiap.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-axpwifiap.dts
@@ -69,14 +69,12 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		pinctrl-0 = <&keys_pin>;
 		pinctrl-names = "default";
 
-		reset {
+		button-reset {
 			label = "Factory Reset Button";
 			linux,code = <KEY_SETUP>;
 			gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
@@ -134,7 +132,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "n25q128a13", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-xp-crs305-1g-4s-bit.dts b/arch/arm/boot/dts/marvell/armada-xp-crs305-1g-4s-bit.dts
index a022c68dc943..c28e140b4afc 100644
--- a/arch/arm/boot/dts/armada-xp-crs305-1g-4s-bit.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-crs305-1g-4s-bit.dts
@@ -15,7 +15,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-xp-crs305-1g-4s.dts b/arch/arm/boot/dts/marvell/armada-xp-crs305-1g-4s.dts
index 010b83b54212..010b83b54212 100644
--- a/arch/arm/boot/dts/armada-xp-crs305-1g-4s.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-crs305-1g-4s.dts
diff --git a/arch/arm/boot/dts/armada-xp-crs305-1g-4s.dtsi b/arch/arm/boot/dts/marvell/armada-xp-crs305-1g-4s.dtsi
index 32fb21b2bf6a..47b003a81bd4 100644
--- a/arch/arm/boot/dts/armada-xp-crs305-1g-4s.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-xp-crs305-1g-4s.dtsi
@@ -80,7 +80,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-xp-crs326-24g-2s-bit.dts b/arch/arm/boot/dts/marvell/armada-xp-crs326-24g-2s-bit.dts
index 21f442afab1f..20ba5c823bb2 100644
--- a/arch/arm/boot/dts/armada-xp-crs326-24g-2s-bit.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-crs326-24g-2s-bit.dts
@@ -15,7 +15,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-xp-crs326-24g-2s.dts b/arch/arm/boot/dts/marvell/armada-xp-crs326-24g-2s.dts
index 83aef43f66d5..83aef43f66d5 100644
--- a/arch/arm/boot/dts/armada-xp-crs326-24g-2s.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-crs326-24g-2s.dts
diff --git a/arch/arm/boot/dts/armada-xp-crs326-24g-2s.dtsi b/arch/arm/boot/dts/marvell/armada-xp-crs326-24g-2s.dtsi
index f3e1a25ca5f2..cab99d8e2911 100644
--- a/arch/arm/boot/dts/armada-xp-crs326-24g-2s.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-xp-crs326-24g-2s.dtsi
@@ -80,7 +80,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-xp-crs328-4c-20s-4s-bit.dts b/arch/arm/boot/dts/marvell/armada-xp-crs328-4c-20s-4s-bit.dts
index e05aee6cdc04..2caa3980fdf6 100644
--- a/arch/arm/boot/dts/armada-xp-crs328-4c-20s-4s-bit.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-crs328-4c-20s-4s-bit.dts
@@ -15,7 +15,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-xp-crs328-4c-20s-4s.dts b/arch/arm/boot/dts/marvell/armada-xp-crs328-4c-20s-4s.dts
index 665757f6e18e..665757f6e18e 100644
--- a/arch/arm/boot/dts/armada-xp-crs328-4c-20s-4s.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-crs328-4c-20s-4s.dts
diff --git a/arch/arm/boot/dts/armada-xp-crs328-4c-20s-4s.dtsi b/arch/arm/boot/dts/marvell/armada-xp-crs328-4c-20s-4s.dtsi
index c8b1355ce15e..7028482ce4b2 100644
--- a/arch/arm/boot/dts/armada-xp-crs328-4c-20s-4s.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-xp-crs328-4c-20s-4s.dtsi
@@ -80,7 +80,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-xp-db-dxbc2.dts b/arch/arm/boot/dts/marvell/armada-xp-db-dxbc2.dts
index 8a3aa616bbd0..02bef8dc4270 100644
--- a/arch/arm/boot/dts/armada-xp-db-dxbc2.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-db-dxbc2.dts
@@ -93,7 +93,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p64";
diff --git a/arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts b/arch/arm/boot/dts/marvell/armada-xp-db-xc3-24g4xg.dts
index 4ec0ae01b61d..d1b61dad0c46 100644
--- a/arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-db-xc3-24g4xg.dts
@@ -89,7 +89,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p64";
diff --git a/arch/arm/boot/dts/armada-xp-db.dts b/arch/arm/boot/dts/marvell/armada-xp-db.dts
index 5d04dc68cf57..75318fd0fc11 100644
--- a/arch/arm/boot/dts/armada-xp-db.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-db.dts
@@ -235,7 +235,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p64", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-xp-gp.dts b/arch/arm/boot/dts/marvell/armada-xp-gp.dts
index b4cca507cf13..d1d348b91c0a 100644
--- a/arch/arm/boot/dts/armada-xp-gp.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-gp.dts
@@ -220,7 +220,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "n25q128a13", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts b/arch/arm/boot/dts/marvell/armada-xp-lenovo-ix4-300d.dts
index 87dcb502f72d..21b95578fe95 100644
--- a/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-lenovo-ix4-300d.dts
@@ -164,11 +164,11 @@
 		};
 	};
 
-	spi3 {
+	spi-3 {
 		compatible = "spi-gpio";
 		status = "okay";
-		gpio-sck = <&gpio0 25 GPIO_ACTIVE_LOW>;
-		gpio-mosi = <&gpio1 15 GPIO_ACTIVE_LOW>; /*gpio 47*/
+		sck-gpios  = <&gpio0 25 GPIO_ACTIVE_LOW>;
+		mosi-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; /*gpio 47*/
 		cs-gpios = <&gpio0 27 GPIO_ACTIVE_LOW>;
 		num-chipselects = <1>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/armada-xp-linksys-mamba.dts b/arch/arm/boot/dts/marvell/armada-xp-linksys-mamba.dts
index 8480a16919a0..ea859f7ea042 100644
--- a/arch/arm/boot/dts/armada-xp-linksys-mamba.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-linksys-mamba.dts
@@ -172,20 +172,18 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		pinctrl-0 = <&keys_pin>;
 		pinctrl-names = "default";
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
 		};
 
-		reset {
+		button-reset {
 			label = "Factory Reset Button";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
@@ -197,7 +195,7 @@
 		pinctrl-0 = <&power_led_pin>;
 		pinctrl-names = "default";
 
-		power {
+		led-power {
 			label = "mamba:white:power";
 			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
@@ -255,7 +253,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "everspin,mr25h256";
@@ -267,44 +265,42 @@
 &mdio {
 	status = "okay";
 
-	switch@0 {
+	ethernet-switch@0 {
 		compatible = "marvell,mv88e6085";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		reg = <0>;
 
-		ports {
+		ethernet-ports {
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			port@0 {
+			ethernet-port@0 {
 				reg = <0>;
 				label = "lan4";
 			};
 
-			port@1 {
+			ethernet-port@1 {
 				reg = <1>;
 				label = "lan3";
 			};
 
-			port@2 {
+			ethernet-port@2 {
 				reg = <2>;
 				label = "lan2";
 			};
 
-			port@3 {
+			ethernet-port@3 {
 				reg = <3>;
 				label = "lan1";
 			};
 
-			port@4 {
+			ethernet-port@4 {
 				reg = <4>;
 				label = "internet";
 			};
 
-			port@5 {
+			ethernet-port@5 {
 				reg = <5>;
-				label = "cpu";
+				phy-mode = "rgmii-id";
 				ethernet = <&eth0>;
 				fixed-link {
 					speed = <1000>;
diff --git a/arch/arm/boot/dts/armada-xp-matrix.dts b/arch/arm/boot/dts/marvell/armada-xp-matrix.dts
index 1395cea12759..1395cea12759 100644
--- a/arch/arm/boot/dts/armada-xp-matrix.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-matrix.dts
diff --git a/arch/arm/boot/dts/armada-xp-mv78230.dtsi b/arch/arm/boot/dts/marvell/armada-xp-mv78230.dtsi
index 8558bf6bb54c..5ea9d509cd30 100644
--- a/arch/arm/boot/dts/armada-xp-mv78230.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-xp-mv78230.dtsi
@@ -83,88 +83,138 @@
 				reg = <0x0800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 58>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 58>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 5>;
 				status = "disabled";
+
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie2: pcie@2,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				assigned-addresses = <0x82001000 0 0x44000 0 0x2000>;
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 59>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
 					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 59>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie2_intc 0>,
+						<0 0 0 2 &pcie2_intc 1>,
+						<0 0 0 3 &pcie2_intc 2>,
+						<0 0 0 4 &pcie2_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <1>;
 				clocks = <&gateclk 6>;
 				status = "disabled";
+
+				pcie2_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie3: pcie@3,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+				assigned-addresses = <0x82001800 0 0x48000 0 0x2000>;
 				reg = <0x1800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 60>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
 					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 60>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie3_intc 0>,
+						<0 0 0 2 &pcie3_intc 1>,
+						<0 0 0 3 &pcie3_intc 2>,
+						<0 0 0 4 &pcie3_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <2>;
 				clocks = <&gateclk 7>;
 				status = "disabled";
+
+				pcie3_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie4: pcie@4,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>;
+				assigned-addresses = <0x82002000 0 0x4c000 0 0x2000>;
 				reg = <0x2000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 61>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
 					  0x81000000 0 0 0x81000000 0x4 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 61>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie4_intc 0>,
+						<0 0 0 2 &pcie4_intc 1>,
+						<0 0 0 3 &pcie4_intc 2>,
+						<0 0 0 4 &pcie4_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <3>;
 				clocks = <&gateclk 8>;
 				status = "disabled";
+
+				pcie4_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie5: pcie@5,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
+				assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
 				reg = <0x2800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 62>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0
 					  0x81000000 0 0 0x81000000 0x5 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 62>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie5_intc 0>,
+						<0 0 0 2 &pcie5_intc 1>,
+						<0 0 0 3 &pcie5_intc 2>,
+						<0 0 0 4 &pcie5_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 9>;
 				status = "disabled";
+
+				pcie5_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 
diff --git a/arch/arm/boot/dts/armada-xp-mv78260.dtsi b/arch/arm/boot/dts/marvell/armada-xp-mv78260.dtsi
index 2d85fe8ac327..6c6fbb9faf5a 100644
--- a/arch/arm/boot/dts/armada-xp-mv78260.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-xp-mv78260.dtsi
@@ -98,160 +98,250 @@
 				reg = <0x0800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 58>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 58>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 5>;
 				status = "disabled";
+
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie2: pcie@2,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				assigned-addresses = <0x82001000 0 0x44000 0 0x2000>;
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 59>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
 					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 59>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie2_intc 0>,
+						<0 0 0 2 &pcie2_intc 1>,
+						<0 0 0 3 &pcie2_intc 2>,
+						<0 0 0 4 &pcie2_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <1>;
 				clocks = <&gateclk 6>;
 				status = "disabled";
+
+				pcie2_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie3: pcie@3,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+				assigned-addresses = <0x82001800 0 0x48000 0 0x2000>;
 				reg = <0x1800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 60>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
 					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 60>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie3_intc 0>,
+						<0 0 0 2 &pcie3_intc 1>,
+						<0 0 0 3 &pcie3_intc 2>,
+						<0 0 0 4 &pcie3_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <2>;
 				clocks = <&gateclk 7>;
 				status = "disabled";
+
+				pcie3_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie4: pcie@4,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x4c000 0 0x2000>;
+				assigned-addresses = <0x82002000 0 0x4c000 0 0x2000>;
 				reg = <0x2000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 61>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
 					  0x81000000 0 0 0x81000000 0x4 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 61>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie4_intc 0>,
+						<0 0 0 2 &pcie4_intc 1>,
+						<0 0 0 3 &pcie4_intc 2>,
+						<0 0 0 4 &pcie4_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <3>;
 				clocks = <&gateclk 8>;
 				status = "disabled";
+
+				pcie4_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie5: pcie@5,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
+				assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
 				reg = <0x2800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 62>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0
 					  0x81000000 0 0 0x81000000 0x5 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 62>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie5_intc 0>,
+						<0 0 0 2 &pcie5_intc 1>,
+						<0 0 0 3 &pcie5_intc 2>,
+						<0 0 0 4 &pcie5_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 9>;
 				status = "disabled";
+
+				pcie5_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie6: pcie@6,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x84000 0 0x2000>;
+				assigned-addresses = <0x82003000 0 0x84000 0 0x2000>;
 				reg = <0x3000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 63>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x6 0 1 0
 					  0x81000000 0 0 0x81000000 0x6 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 63>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie6_intc 0>,
+						<0 0 0 2 &pcie6_intc 1>,
+						<0 0 0 3 &pcie6_intc 2>,
+						<0 0 0 4 &pcie6_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <1>;
 				clocks = <&gateclk 10>;
 				status = "disabled";
+
+				pcie6_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie7: pcie@7,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x88000 0 0x2000>;
+				assigned-addresses = <0x82003800 0 0x88000 0 0x2000>;
 				reg = <0x3800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 64>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x7 0 1 0
 					  0x81000000 0 0 0x81000000 0x7 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 64>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie7_intc 0>,
+						<0 0 0 2 &pcie7_intc 1>,
+						<0 0 0 3 &pcie7_intc 2>,
+						<0 0 0 4 &pcie7_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <2>;
 				clocks = <&gateclk 11>;
 				status = "disabled";
+
+				pcie7_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie8: pcie@8,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x8c000 0 0x2000>;
+				assigned-addresses = <0x82004000 0 0x8c000 0 0x2000>;
 				reg = <0x4000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 65>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x8 0 1 0
 					  0x81000000 0 0 0x81000000 0x8 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 65>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie8_intc 0>,
+						<0 0 0 2 &pcie8_intc 1>,
+						<0 0 0 3 &pcie8_intc 2>,
+						<0 0 0 4 &pcie8_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <3>;
 				clocks = <&gateclk 12>;
 				status = "disabled";
+
+				pcie8_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie9: pcie@9,0 {
 				device_type = "pci";
-				assigned-addresses = <0x82000800 0 0x42000 0 0x2000>;
+				assigned-addresses = <0x82004800 0 0x42000 0 0x2000>;
 				reg = <0x4800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 99>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0
 					  0x81000000 0 0 0x81000000 0x9 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 99>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie9_intc 0>,
+						<0 0 0 2 &pcie9_intc 1>,
+						<0 0 0 3 &pcie9_intc 2>,
+						<0 0 0 4 &pcie9_intc 3>;
 				marvell,pcie-port = <2>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 26>;
 				status = "disabled";
+
+				pcie9_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 
diff --git a/arch/arm/boot/dts/armada-xp-mv78460.dtsi b/arch/arm/boot/dts/marvell/armada-xp-mv78460.dtsi
index 230a3fd36b30..16185edf9aa5 100644
--- a/arch/arm/boot/dts/armada-xp-mv78460.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-xp-mv78460.dtsi
@@ -119,16 +119,26 @@
 				reg = <0x0800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 58>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 58>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 5>;
 				status = "disabled";
+
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie2: pcie@2,0 {
@@ -137,16 +147,26 @@
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 59>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
 					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 59>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie2_intc 0>,
+						<0 0 0 2 &pcie2_intc 1>,
+						<0 0 0 3 &pcie2_intc 2>,
+						<0 0 0 4 &pcie2_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <1>;
 				clocks = <&gateclk 6>;
 				status = "disabled";
+
+				pcie2_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie3: pcie@3,0 {
@@ -155,16 +175,26 @@
 				reg = <0x1800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 60>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
 					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 60>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie3_intc 0>,
+						<0 0 0 2 &pcie3_intc 1>,
+						<0 0 0 3 &pcie3_intc 2>,
+						<0 0 0 4 &pcie3_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <2>;
 				clocks = <&gateclk 7>;
 				status = "disabled";
+
+				pcie3_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie4: pcie@4,0 {
@@ -173,16 +203,26 @@
 				reg = <0x2000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 61>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
 					  0x81000000 0 0 0x81000000 0x4 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 61>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie4_intc 0>,
+						<0 0 0 2 &pcie4_intc 1>,
+						<0 0 0 3 &pcie4_intc 2>,
+						<0 0 0 4 &pcie4_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <3>;
 				clocks = <&gateclk 8>;
 				status = "disabled";
+
+				pcie4_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie5: pcie@5,0 {
@@ -191,16 +231,26 @@
 				reg = <0x2800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 62>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0
 					  0x81000000 0 0 0x81000000 0x5 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 62>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie5_intc 0>,
+						<0 0 0 2 &pcie5_intc 1>,
+						<0 0 0 3 &pcie5_intc 2>,
+						<0 0 0 4 &pcie5_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 9>;
 				status = "disabled";
+
+				pcie5_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie6: pcie@6,0 {
@@ -209,16 +259,26 @@
 				reg = <0x3000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 63>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x6 0 1 0
 					  0x81000000 0 0 0x81000000 0x6 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 63>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie6_intc 0>,
+						<0 0 0 2 &pcie6_intc 1>,
+						<0 0 0 3 &pcie6_intc 2>,
+						<0 0 0 4 &pcie6_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <1>;
 				clocks = <&gateclk 10>;
 				status = "disabled";
+
+				pcie6_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie7: pcie@7,0 {
@@ -227,16 +287,26 @@
 				reg = <0x3800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 64>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x7 0 1 0
 					  0x81000000 0 0 0x81000000 0x7 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 64>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie7_intc 0>,
+						<0 0 0 2 &pcie7_intc 1>,
+						<0 0 0 3 &pcie7_intc 2>,
+						<0 0 0 4 &pcie7_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <2>;
 				clocks = <&gateclk 11>;
 				status = "disabled";
+
+				pcie7_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie8: pcie@8,0 {
@@ -245,16 +315,26 @@
 				reg = <0x4000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 65>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x8 0 1 0
 					  0x81000000 0 0 0x81000000 0x8 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 65>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie8_intc 0>,
+						<0 0 0 2 &pcie8_intc 1>,
+						<0 0 0 3 &pcie8_intc 2>,
+						<0 0 0 4 &pcie8_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <3>;
 				clocks = <&gateclk 12>;
 				status = "disabled";
+
+				pcie8_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie9: pcie@9,0 {
@@ -263,16 +343,26 @@
 				reg = <0x4800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 99>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0
 					  0x81000000 0 0 0x81000000 0x9 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 99>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie9_intc 0>,
+						<0 0 0 2 &pcie9_intc 1>,
+						<0 0 0 3 &pcie9_intc 2>,
+						<0 0 0 4 &pcie9_intc 3>;
 				marvell,pcie-port = <2>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 26>;
 				status = "disabled";
+
+				pcie9_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie10: pcie@a,0 {
@@ -281,16 +371,26 @@
 				reg = <0x5000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 103>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0xa 0 1 0
 					  0x81000000 0 0 0x81000000 0xa 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 103>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie10_intc 0>,
+						<0 0 0 2 &pcie10_intc 1>,
+						<0 0 0 3 &pcie10_intc 2>,
+						<0 0 0 4 &pcie10_intc 3>;
 				marvell,pcie-port = <3>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 27>;
 				status = "disabled";
+
+				pcie10_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 
diff --git a/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts b/arch/arm/boot/dts/marvell/armada-xp-netgear-rn2120.dts
index 8ea73587db81..31933f81144e 100644
--- a/arch/arm/boot/dts/armada-xp-netgear-rn2120.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-netgear-rn2120.dts
@@ -121,11 +121,11 @@
 	};
 
 	clocks {
-	       g762_clk: g762-oscillator {
-			 compatible = "fixed-clock";
-			 #clock-cells = <0>;
-			 clock-frequency = <32768>;
-	       };
+		g762_clk: g762-oscillator {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
 	};
 
 	gpio-leds {
diff --git a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts b/arch/arm/boot/dts/marvell/armada-xp-openblocks-ax3-4.dts
index 0efcc166dabf..1ecf72a61bca 100644
--- a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-openblocks-ax3-4.dts
@@ -97,12 +97,10 @@
 				};
 			};
 
-			gpio_keys {
+			gpio-keys {
 				compatible = "gpio-keys";
-				#address-cells = <1>;
-				#size-cells = <0>;
 
-				init {
+				button-init {
 					label = "Init Button";
 					linux,code = <KEY_POWER>;
 					gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/armada-xp-synology-ds414.dts b/arch/arm/boot/dts/marvell/armada-xp-synology-ds414.dts
index 809e821d7399..1b65059794bf 100644
--- a/arch/arm/boot/dts/armada-xp-synology-ds414.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-synology-ds414.dts
@@ -109,65 +109,60 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		pinctrl-0 = <&sata1_pwr_pin &sata2_pwr_pin
-			     &sata3_pwr_pin &sata4_pwr_pin>;
+	sata1_regulator: sata1-regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "SATA1 Power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		startup-delay-us = <2000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&sata1_pwr_pin>;
 		pinctrl-names = "default";
+	};
 
-		sata1_regulator: sata1-regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "SATA1 Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			startup-delay-us = <2000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>;
-		};
-
-		sata2_regulator: sata2-regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "SATA2 Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			startup-delay-us = <4000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
-		};
+	sata2_regulator: sata2-regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "SATA2 Power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		startup-delay-us = <4000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&sata2_pwr_pin>;
+		pinctrl-names = "default";
+	};
 
-		sata3_regulator: sata3-regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "SATA3 Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			startup-delay-us = <6000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>;
-		};
+	sata3_regulator: sata3-regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "SATA3 Power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		startup-delay-us = <6000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&sata3_pwr_pin>;
+		pinctrl-names = "default";
+	};
 
-		sata4_regulator: sata4-regulator@4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			regulator-name = "SATA4 Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			startup-delay-us = <8000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
-		};
+	sata4_regulator: sata4-regulator-4 {
+		compatible = "regulator-fixed";
+		regulator-name = "SATA4 Power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		startup-delay-us = <8000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&sata4_pwr_pin>;
+		pinctrl-names = "default";
 	};
 };
 
@@ -274,7 +269,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q064", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-xp.dtsi b/arch/arm/boot/dts/marvell/armada-xp.dtsi
index 6c19984d668e..4297482da62f 100644
--- a/arch/arm/boot/dts/armada-xp.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-xp.dtsi
@@ -260,6 +260,7 @@
 	compatible = "marvell,armada-xp-wdt";
 	clocks = <&coreclk 2>, <&refclk>;
 	clock-names = "nbclk", "fixed";
+	interrupts = <93>, <38>;
 };
 
 &cpurst {
diff --git a/arch/arm/boot/dts/dove-cm-a510.dtsi b/arch/arm/boot/dts/marvell/dove-cm-a510.dtsi
index 9b9dfbe07be4..621cb145a8f6 100644
--- a/arch/arm/boot/dts/dove-cm-a510.dtsi
+++ b/arch/arm/boot/dts/marvell/dove-cm-a510.dtsi
@@ -101,32 +101,34 @@
 		pinctrl-0 = <&pmx_nand_gpo>;
 		pinctrl-names = "default";
 
-		system {
+		led-system {
 			label = "cm-a510:system:green";
 			gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		wifi_power: regulator@1 {
-			compatible = "regulator-fixed";
-			regulator-name = "WiFi Power";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio2 7 GPIO_ACTIVE_HIGH>;
-		};
+	wifi_power: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "WiFi Power";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 7 GPIO_ACTIVE_HIGH>;
 	};
 };
 
 /* Optional RTL8211D GbE PHY on SMI address 0x03 */
-&ethphy {
-	reg = <3>;
-	status = "disabled";
+&mdio {
+	ethphy: ethernet-phy@3 {
+		reg = <3>;
+		status = "disabled";
+	};
+};
+
+&eth {
+	ethernet-port@0 {
+		phy-handle = <&ethphy>;
+	};
 };
 
 &i2c0 {
diff --git a/arch/arm/boot/dts/dove-cubox-es.dts b/arch/arm/boot/dts/marvell/dove-cubox-es.dts
index ad361ec1361d..ad361ec1361d 100644
--- a/arch/arm/boot/dts/dove-cubox-es.dts
+++ b/arch/arm/boot/dts/marvell/dove-cubox-es.dts
diff --git a/arch/arm/boot/dts/dove-cubox.dts b/arch/arm/boot/dts/marvell/dove-cubox.dts
index 3e1584e787ae..bcaaf8320c45 100644
--- a/arch/arm/boot/dts/dove-cubox.dts
+++ b/arch/arm/boot/dts/marvell/dove-cubox.dts
@@ -21,31 +21,24 @@
 		pinctrl-0 = <&pmx_gpio_18>;
 		pinctrl-names = "default";
 
-		power {
+		led-power {
 			label = "Power";
 			gpios = <&gpio0 18 1>;
 			default-state = "keep";
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		usb_power: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "USB Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio0 1 0>;
-			pinctrl-0 = <&pmx_gpio_1>;
-			pinctrl-names = "default";
-		};
+	usb_power: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "USB Power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio0 1 0>;
+		pinctrl-0 = <&pmx_gpio_1>;
+		pinctrl-names = "default";
 	};
 
 	clocks {
@@ -72,11 +65,18 @@
 &uart0 { status = "okay"; };
 &sata0 { status = "okay"; };
 &mdio { status = "okay"; };
-&eth { status = "okay"; };
+&eth {
+	status = "okay";
+	ethernet-port@0 {
+		phy-handle = <&ethphy>;
+	};
+};
 
-&ethphy {
-	compatible = "marvell,88e1310";
-	reg = <1>;
+&mdio {
+	ethphy: ethernet-phy@1 {
+		compatible = "marvell,88e1310";
+		reg = <1>;
+	};
 };
 
 &gpu {
@@ -101,7 +101,7 @@
 		/* connect xtal input as source of pll0 and pll1 */
 		silabs,pll-source = <0 0>, <1 0>;
 
-		clkout0 {
+		clkout@0 {
 			reg = <0>;
 			silabs,drive-strength = <8>;
 			silabs,multisynth-source = <0>;
@@ -109,7 +109,7 @@
 			silabs,pll-master;
 		};
 
-		clkout2 {
+		clkout@2 {
 			reg = <2>;
 			silabs,drive-strength = <8>;
 			silabs,multisynth-source = <1>;
@@ -127,7 +127,7 @@
 	status = "okay";
 
 	/* spi0.0: 4M Flash Winbond W25Q32BV */
-	spi-flash@0 {
+	flash@0 {
 		compatible = "st,w25q32";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/dove-d2plug.dts b/arch/arm/boot/dts/marvell/dove-d2plug.dts
index 273f12ca2512..79ee2b32409d 100644
--- a/arch/arm/boot/dts/dove-d2plug.dts
+++ b/arch/arm/boot/dts/marvell/dove-d2plug.dts
@@ -21,17 +21,17 @@
 		pinctrl-0 = <&pmx_gpio_0 &pmx_gpio_1 &pmx_gpio_2>;
 		pinctrl-names = "default";
 
-		wlan-ap {
+		led-wlan-ap {
 			label = "wlan-ap";
 			gpios = <&gpio0 0 1>;
 		};
 
-		wlan-act {
+		led-wlan-act {
 			label = "wlan-act";
 			gpios = <&gpio0 1 1>;
 		};
 
-		bluetooth-act {
+		led-bluetooth-act {
 			label = "bt-act";
 			gpios = <&gpio0 2 1>;
 		};
@@ -62,7 +62,7 @@
 	status = "okay";
 
 	/* spi0.0: 4M Flash Macronix MX25L3205D */
-	spi-flash@0 {
+	flash@0 {
 		compatible = "st,m25l3205d";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/dove-d3plug.dts b/arch/arm/boot/dts/marvell/dove-d3plug.dts
index 826026c28f90..a451fd576990 100644
--- a/arch/arm/boot/dts/dove-d3plug.dts
+++ b/arch/arm/boot/dts/marvell/dove-d3plug.dts
@@ -21,40 +21,33 @@
 		pinctrl-0 = <&pmx_gpio_0 &pmx_gpio_1 &pmx_gpio_2>;
 		pinctrl-names = "default";
 
-		wlan-act {
+		led-wlan-act {
 			label = "wlan-act";
 			gpios = <&gpio0 0 1>;
 		};
 
-		wlan-ap {
+		led-wlan-ap {
 			label = "wlan-ap";
 			gpios = <&gpio0 1 1>;
 		};
 
-		status {
+		led-status {
 			label = "status";
 			gpios = <&gpio0 2 1>;
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		usb_power: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "USB Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio0 8 0>;
-			pinctrl-0 = <&pmx_gpio_8>;
-			pinctrl-names = "default";
-		};
+	usb_power: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "USB Power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio0 8 0>;
+		pinctrl-0 = <&pmx_gpio_8>;
+		pinctrl-names = "default";
 	};
 };
 
@@ -79,7 +72,7 @@
 	status = "okay";
 
 	/* spi0.0: 2M Flash Macronix MX25L1605D */
-	spi-flash@0 {
+	flash@0 {
 		compatible = "st,m25l1605d";
 		spi-max-frequency = <86000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/dove-dove-db.dts b/arch/arm/boot/dts/marvell/dove-dove-db.dts
index 1754a62e014e..c1912dc6bfc3 100644
--- a/arch/arm/boot/dts/dove-dove-db.dts
+++ b/arch/arm/boot/dts/marvell/dove-dove-db.dts
@@ -27,7 +27,7 @@
 	status = "okay";
 
 	/* spi0.0: 4M Flash ST-M25P32-VMF6P */
-	spi-flash@0 {
+	flash@0 {
 		compatible = "st,m25p32";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/dove-sbc-a510.dts b/arch/arm/boot/dts/marvell/dove-sbc-a510.dts
index df021f9b0117..8585ee5533bf 100644
--- a/arch/arm/boot/dts/dove-sbc-a510.dts
+++ b/arch/arm/boot/dts/marvell/dove-sbc-a510.dts
@@ -76,22 +76,20 @@
 		stdout-path = &uart0;
 	};
 
-	regulators {
-		usb0_power: regulator@2 {
-			compatible = "regulator-fixed";
-			regulator-name = "USB Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio_ext 0 GPIO_ACTIVE_HIGH>;
-		};
-
-		mmc_power: regulator@3 {
-			compatible = "regulator-fixed";
-			regulator-name = "MMC Power";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio_ext 13 GPIO_ACTIVE_HIGH>;
-		};
+	usb0_power: regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "USB Power";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio_ext 0 GPIO_ACTIVE_HIGH>;
+	};
+
+	mmc_power: regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "MMC Power";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio_ext 13 GPIO_ACTIVE_HIGH>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/dove.dtsi b/arch/arm/boot/dts/marvell/dove.dtsi
index 89e0bdaf3a85..062c86361640 100644
--- a/arch/arm/boot/dts/dove.dtsi
+++ b/arch/arm/boot/dts/marvell/dove.dtsi
@@ -122,14 +122,24 @@
 				bus-range = <0x00 0xff>;
 
 				#interrupt-cells = <1>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &intc 16>;
+				interrupt-names = "intx", "error";
+				interrupts = <16>, <15>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie0_intc 0>,
+						<0 0 0 2 &pcie0_intc 1>,
+						<0 0 0 3 &pcie0_intc 2>,
+						<0 0 0 4 &pcie0_intc 3>;
+
+				pcie0_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie1: pcie@2 {
 				device_type = "pci";
 				status = "disabled";
-				assigned-addresses = <0x82002800 0 0x80000 0 0x2000>;
+				assigned-addresses = <0x82001000 0 0x80000 0 0x2000>;
 				reg = <0x1000 0 0 0 0>;
 				clocks = <&gate_clk 5>;
 				marvell,pcie-port = <1>;
@@ -141,8 +151,18 @@
 				bus-range = <0x00 0xff>;
 
 				#interrupt-cells = <1>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &intc 18>;
+				interrupt-names = "intx", "error";
+				interrupts = <18>, <17>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
+
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 
@@ -362,7 +382,6 @@
 					interrupts = <29>;
 					/* overwrite MAC address in bootloader */
 					local-mac-address = [00 00 00 00 00 00];
-					phy-handle = <&ethphy>;
 				};
 			};
 
@@ -374,10 +393,6 @@
 				interrupts = <30>;
 				clocks = <&gate_clk 2>;
 				status = "disabled";
-
-				ethphy: ethernet-phy {
-					/* set phy address in board file */
-				};
 			};
 
 			sdio0: sdio-host@92000 {
@@ -407,7 +422,7 @@
 				clocks = <&gate_clk 3>;
 				clock-names = "sata";
 				#phy-cells = <0>;
-				status = "ok";
+				status = "okay";
 			};
 
 			audio0: audio-controller@b0000 {
diff --git a/arch/arm/boot/dts/marvell/kirkwood-4i-edge-200.dts b/arch/arm/boot/dts/marvell/kirkwood-4i-edge-200.dts
new file mode 100644
index 000000000000..b1749d3f60b7
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/kirkwood-4i-edge-200.dts
@@ -0,0 +1,205 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Endian 4i Edge 200 Board Description
+ * Note: Endian UTM Mini is hardware clone of Endian Edge 200
+ * Copyright 2021-2022 Pawel Dembicki <paweldembicki@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Endian 4i Edge 200";
+	compatible = "endian,4i-edge-200", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		stdout-path = &uart0;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&pmx_led>;
+		pinctrl-names = "default";
+
+		led-1 {
+			function = LED_FUNCTION_SD;
+			color = <LED_COLOR_ID_AMBER>;
+			gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+		};
+
+		led-2 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_AMBER>;
+			gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-3 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&eth0 {
+	status = "okay";
+};
+
+&eth0port {
+	speed = <1000>;
+	duplex = <1>;
+};
+
+&eth1 {
+	status = "okay";
+};
+
+&eth1port {
+	phy-handle = <&ethphyb>;
+};
+
+&mdio {
+	status = "okay";
+
+	ethphyb: ethernet-phy@b {
+		reg = <0x0b>;
+
+		marvell,reg-init =
+			/* link-activity, bi-color mode 4 */
+			<3 0x10 0xfff0 0xf>; /* Reg 3,16 <- 0xzzzf */
+	};
+
+	switch0: switch@11 {
+		compatible = "marvell,mv88e6085";
+		reg = <0x11>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				label = "port1";
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "port2";
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "port3";
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "port4";
+			};
+
+			port@5 {
+				reg = <5>;
+				phy-mode = "rgmii-id";
+				ethernet = <&eth0port>;
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+		};
+	};
+};
+
+&nand {
+	status = "okay";
+	pinctrl-0 = <&pmx_nand>;
+	pinctrl-names = "default";
+
+	partition@0 {
+		label = "u-boot";
+		reg = <0x00000000 0x000a0000>;
+		read-only;
+	};
+
+	partition@a0000 {
+		label = "u-boot-env";
+		reg = <0x000a0000 0x00060000>;
+		read-only;
+	};
+
+	partition@100000 {
+		label = "kernel";
+		reg = <0x00100000 0x00400000>;
+	};
+
+	partition@500000 {
+		label = "ubi";
+		reg = <0x00500000 0x1fb00000>;
+	};
+};
+
+&pciec {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-0 = <&pmx_sysrst>;
+	pinctrl-names = "default";
+
+	pmx_sysrst: pmx-sysrst {
+		marvell,pins = "mpp6";
+		marvell,function = "sysrst";
+	};
+
+	pmx_sdio_cd: pmx-sdio-cd {
+		marvell,pins = "mpp28";
+		marvell,function = "gpio";
+	};
+
+	pmx_led: pmx-led {
+		marvell,pins = "mpp34", "mpp35", "mpp49";
+		marvell,function = "gpio";
+	};
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sata_phy0 {
+	status = "disabled";
+};
+
+&sata_phy1 {
+	status = "disabled";
+};
+
+&sdio {
+	pinctrl-0 = <&pmx_sdio_cd>;
+	pinctrl-names = "default";
+	status = "okay";
+	cd-gpios = <&gpio0 28 9>;
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/kirkwood-6192.dtsi b/arch/arm/boot/dts/marvell/kirkwood-6192.dtsi
index 396bcba08adb..705c0d7effed 100644
--- a/arch/arm/boot/dts/kirkwood-6192.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-6192.dtsi
@@ -26,12 +26,22 @@
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &intc 9>;
+				interrupt-names = "intx", "error";
+				interrupts = <9>, <44>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie_intc 0>,
+						<0 0 0 2 &pcie_intc 1>,
+						<0 0 0 3 &pcie_intc 2>,
+						<0 0 0 4 &pcie_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gate_clk 2>;
 				status = "disabled";
+
+				pcie_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/kirkwood-6281.dtsi b/arch/arm/boot/dts/marvell/kirkwood-6281.dtsi
index faa05849a40d..8e311165fd13 100644
--- a/arch/arm/boot/dts/kirkwood-6281.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-6281.dtsi
@@ -26,12 +26,22 @@
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &intc 9>;
+				interrupt-names = "intx", "error";
+				interrupts = <9>, <44>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie_intc 0>,
+						<0 0 0 2 &pcie_intc 1>,
+						<0 0 0 3 &pcie_intc 2>,
+						<0 0 0 4 &pcie_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gate_clk 2>;
 				status = "disabled";
+
+				pcie_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/kirkwood-6282.dtsi b/arch/arm/boot/dts/marvell/kirkwood-6282.dtsi
index e84c54b77dea..e33723160ce7 100644
--- a/arch/arm/boot/dts/kirkwood-6282.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-6282.dtsi
@@ -30,12 +30,22 @@
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &intc 9>;
+				interrupt-names = "intx", "error";
+				interrupts = <9>, <44>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie0_intc 0>,
+						<0 0 0 2 &pcie0_intc 1>,
+						<0 0 0 3 &pcie0_intc 2>,
+						<0 0 0 4 &pcie0_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gate_clk 2>;
 				status = "disabled";
+
+				pcie0_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie1: pcie@2,0 {
@@ -48,12 +58,22 @@
 				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
 					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &intc 10>;
+				interrupt-names = "intx", "error";
+				interrupts = <10>, <45>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gate_clk 18>;
 				status = "disabled";
+
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/kirkwood-98dx4122.dtsi b/arch/arm/boot/dts/marvell/kirkwood-98dx4122.dtsi
index 299c147298c3..c3469a2fc58a 100644
--- a/arch/arm/boot/dts/kirkwood-98dx4122.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-98dx4122.dtsi
@@ -26,12 +26,22 @@
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &intc 9>;
+				interrupt-names = "intx", "error";
+				interrupts = <9>, <44>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie_intc 0>,
+						<0 0 0 2 &pcie_intc 1>,
+						<0 0 0 3 &pcie_intc 2>,
+						<0 0 0 4 &pcie_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gate_clk 2>;
 				status = "disabled";
+
+				pcie_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/kirkwood-b3.dts b/arch/arm/boot/dts/marvell/kirkwood-b3.dts
index a7636fe28501..681343c1357a 100644
--- a/arch/arm/boot/dts/kirkwood-b3.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-b3.dts
@@ -187,7 +187,7 @@
 
 /* Wifi model has Atheros chipset on pcie port */
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-blackarmor-nas220.dts b/arch/arm/boot/dts/marvell/kirkwood-blackarmor-nas220.dts
index 07fbfca444d5..36b90c632fd6 100644
--- a/arch/arm/boot/dts/kirkwood-blackarmor-nas220.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-blackarmor-nas220.dts
@@ -35,13 +35,13 @@
 	gpio_keys {
 		compatible = "gpio-keys";
 
-		reset {
+		button-reset {
 			label = "Reset";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
 		};
 
-		button {
+		button-power {
 			label = "Power";
 			linux,code = <KEY_SLEEP>;
 			gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
@@ -51,7 +51,7 @@
 	gpio-leds {
 		compatible = "gpio-leds";
 
-		blue-power {
+		led-blue-power {
 			label = "nas220:blue:power";
 			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
diff --git a/arch/arm/boot/dts/kirkwood-c200-v1.dts b/arch/arm/boot/dts/marvell/kirkwood-c200-v1.dts
index f59ff7578dfc..7e3ee64d4bdf 100644
--- a/arch/arm/boot/dts/kirkwood-c200-v1.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-c200-v1.dts
@@ -29,25 +29,25 @@
 		pinctrl-0 = <&pmx_buttons>;
 		pinctrl-names = "default";
 
-		power {
+		button-power {
 			label = "Power Button";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
 		};
 
-		reset {
+		button-reset {
 			label = "Reset Button";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
 		};
 
-		usb1 {
+		button-usb1 {
 			label = "USB1 Button";
 			linux,code = <BTN_0>;
 			gpios = <&gpio0 28 GPIO_ACTIVE_LOW>;
 		};
 
-		usb2 {
+		button-usb2 {
 			label = "USB2 Button";
 			linux,code = <BTN_1>;
 			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/kirkwood-cloudbox.dts b/arch/arm/boot/dts/marvell/kirkwood-cloudbox.dts
index 448b0cd23b5f..151edcd140a0 100644
--- a/arch/arm/boot/dts/kirkwood-cloudbox.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-cloudbox.dts
@@ -58,10 +58,8 @@
 
 	gpio_keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		power {
+		key-power {
 			label = "Power push button";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
@@ -71,11 +69,11 @@
 	gpio-leds {
 		compatible = "gpio-leds";
 
-		red-fail {
+		led-red-fail {
 			label = "cloudbox:red:fail";
 			gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
 		};
-		blue-sata {
+		led-blue-sata {
 			label = "cloudbox:blue:sata";
 			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
 		};
diff --git a/arch/arm/boot/dts/kirkwood-d2net.dts b/arch/arm/boot/dts/marvell/kirkwood-d2net.dts
index bd3b266dd766..fcce8730d3e3 100644
--- a/arch/arm/boot/dts/kirkwood-d2net.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-d2net.dts
@@ -37,7 +37,7 @@
 	gpio-leds {
 		compatible = "gpio-leds";
 
-		red-fail {
+		led-red-fail {
 			label = "d2net_v2:red:fail";
 			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
 		};
diff --git a/arch/arm/boot/dts/kirkwood-db-88f6281.dts b/arch/arm/boot/dts/marvell/kirkwood-db-88f6281.dts
index 2adb17c955aa..a9a8e6b744c7 100644
--- a/arch/arm/boot/dts/kirkwood-db-88f6281.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-db-88f6281.dts
@@ -18,7 +18,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-db-88f6282.dts b/arch/arm/boot/dts/marvell/kirkwood-db-88f6282.dts
index f84a48539917..6dc6579d4524 100644
--- a/arch/arm/boot/dts/kirkwood-db-88f6282.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-db-88f6282.dts
@@ -18,7 +18,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-db.dtsi b/arch/arm/boot/dts/marvell/kirkwood-db.dtsi
index 6fe2e31534af..8bacaeb4f4bd 100644
--- a/arch/arm/boot/dts/kirkwood-db.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-db.dtsi
@@ -39,7 +39,7 @@
 			status = "okay";
 		};
 
-		ehci@50000 {
+		usb@50000 {
 			status = "okay";
 		};
 
diff --git a/arch/arm/boot/dts/kirkwood-dir665.dts b/arch/arm/boot/dts/marvell/kirkwood-dir665.dts
index b3ad3f607d31..36394d1ab3e2 100644
--- a/arch/arm/boot/dts/kirkwood-dir665.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-dir665.dts
@@ -78,7 +78,7 @@
 
 		spi@10600 {
 			status = "okay";
-			m25p80@0 {
+			flash@0 {
 				#address-cells = <1>;
 				#size-cells = <1>;
 				compatible = "mxicy,mx25l12805d", "jedec,spi-nor";
@@ -129,7 +129,7 @@
 			status = "okay";
 		};
 
-		ehci@50000 {
+		usb@50000 {
 			status = "okay";
 		};
 	};
@@ -137,38 +137,38 @@
 	gpio-leds {
 		compatible = "gpio-leds";
 
-		blue-usb {
+		led-blue-usb {
 			label = "dir665:blue:usb";
 			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
 		};
-		blue-internet {
+		led-blue-internet {
 			/* Can only be turned on if the Internet
 			 * Ethernet port has Link
 			 */
 			label = "dir665:blue:internet";
 			gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
 		};
-		amber-internet {
+		led-amber-internet {
 			label = "dir665:amber:internet";
 			gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
 		};
-		blue-wifi5g {
+		led-blue-wifi5g {
 			label = "dir665:blue:5g";
 			gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
 		};
-		blue-status {
+		led-blue-status {
 			label = "dir665:blue:status";
 			gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
 		};
-		blue-wps {
+		led-blue-wps {
 			label = "dir665:blue:wps";
 			gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
 		};
-		amber-status {
+		led-amber-status {
 			label = "dir665:amber:status";
 			gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
 		};
-		blue-24g {
+		led-blue-24g {
 			label = "dir665:blue:24g";
 			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
 		};
@@ -176,15 +176,13 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		reset {
+		button-reset {
 			label = "reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio0 28 GPIO_ACTIVE_LOW>;
 		};
-		wps {
+		button-wps {
 			label = "wps";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
@@ -211,18 +209,18 @@
 			};
 
 			port@1 {
-			       reg = <1>;
-			       label = "lan3";
+				reg = <1>;
+				label = "lan3";
 			};
 
 			port@2 {
-			       reg = <2>;
-			       label = "lan2";
+				reg = <2>;
+				label = "lan2";
 			};
 
 			port@3 {
-			       reg = <3>;
-			       label = "lan1";
+				reg = <3>;
+				label = "lan1";
 			};
 
 			port@4 {
@@ -232,7 +230,7 @@
 
 			port@6 {
 				reg = <6>;
-				label = "cpu";
+				phy-mode = "rgmii-id";
 				ethernet = <&eth0port>;
 				fixed-link {
 					speed = <1000>;
@@ -251,6 +249,7 @@
 	ethernet0-port@0 {
 		speed = <1000>;
 		duplex = <1>;
+		phy-mode = "rgmii";
 	};
 };
 
@@ -268,7 +267,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-dns320.dts b/arch/arm/boot/dts/marvell/kirkwood-dns320.dts
index d6b0f418fd01..d8279e0c4c4f 100644
--- a/arch/arm/boot/dts/kirkwood-dns320.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-dns320.dts
@@ -24,24 +24,24 @@
 			     &pmx_led_white_usb>;
 		pinctrl-names = "default";
 
-		blue-power {
+		led-blue-power {
 			label = "dns320:blue:power";
 			gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
 			default-state = "keep";
 		};
-		blue-usb {
+		led-blue-usb {
 			label = "dns320:blue:usb";
 			gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
 		};
-		orange-l_hdd {
+		led-orange-l_hdd {
 			label = "dns320:orange:l_hdd";
 			gpios = <&gpio0 28 GPIO_ACTIVE_LOW>;
 		};
-		orange-r_hdd {
+		led-orange-r_hdd {
 			label = "dns320:orange:r_hdd";
 			gpios = <&gpio0 27 GPIO_ACTIVE_LOW>;
 		};
-		orange-usb {
+		led-orange-usb {
 			label = "dns320:orange:usb";
 			gpios = <&gpio1 3 GPIO_ACTIVE_LOW>; /* GPIO 35 */
 		};
diff --git a/arch/arm/boot/dts/kirkwood-dns325.dts b/arch/arm/boot/dts/marvell/kirkwood-dns325.dts
index 94d9c06cbbf5..7f396195e977 100644
--- a/arch/arm/boot/dts/kirkwood-dns325.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-dns325.dts
@@ -24,24 +24,24 @@
 			     &pmx_led_white_usb>;
 		pinctrl-names = "default";
 
-		white-power {
+		led-white-power {
 			label = "dns325:white:power";
 			gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
 			default-state = "keep";
 		};
-		white-usb {
+		led-white-usb {
 			label = "dns325:white:usb";
 			gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; /* GPIO 43 */
 		};
-		red-l_hdd {
+		led-red-l_hdd {
 			label = "dns325:red:l_hdd";
 			gpios = <&gpio0 28 GPIO_ACTIVE_LOW>;
 		};
-		red-r_hdd {
+		led-red-r_hdd {
 			label = "dns325:red:r_hdd";
 			gpios = <&gpio0 27 GPIO_ACTIVE_LOW>;
 		};
-		red-usb {
+		led-red-usb {
 			label = "dns325:red:usb";
 			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
 		};
diff --git a/arch/arm/boot/dts/kirkwood-dnskw.dtsi b/arch/arm/boot/dts/marvell/kirkwood-dnskw.dtsi
index eb917462b219..20bcd031f3f5 100644
--- a/arch/arm/boot/dts/kirkwood-dnskw.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-dnskw.dtsi
@@ -8,23 +8,21 @@
 
 	gpio_keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		pinctrl-0 = <&pmx_button_power &pmx_button_unmount
 			     &pmx_button_reset>;
 		pinctrl-names = "default";
 
-		power {
+		button-power {
 			label = "Power button";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
 		};
-		eject {
+		button-eject {
 			label = "USB unmount button";
 			linux,code = <KEY_EJECTCD>;
 			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
 		};
-		reset {
+		button-reset {
 			label = "Reset button";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
@@ -38,9 +36,9 @@
 		pinctrl-names = "default";
 		gpios = <&gpio1 14 GPIO_ACTIVE_HIGH
 			 &gpio1 13 GPIO_ACTIVE_HIGH>;
-		gpio-fan,speed-map = <0    0
-				      3000 1
-				      6000 2>;
+		gpio-fan,speed-map = <0    0>,
+				     <3000 1>,
+				     <6000 2>;
 	};
 
 	gpio_poweroff {
diff --git a/arch/arm/boot/dts/kirkwood-dockstar.dts b/arch/arm/boot/dts/marvell/kirkwood-dockstar.dts
index 264938dfa4d9..090f1e2e5bb6 100644
--- a/arch/arm/boot/dts/kirkwood-dockstar.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-dockstar.dts
@@ -42,12 +42,12 @@
 		pinctrl-0 = <&pmx_led_green &pmx_led_orange>;
 		pinctrl-names = "default";
 
-		health {
+		led-health {
 			label = "status:green:health";
 			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
 			default-state = "keep";
 		};
-		fault {
+		led-fault {
 			label = "status:orange:fault";
 			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
 		};
diff --git a/arch/arm/boot/dts/kirkwood-dreamplug.dts b/arch/arm/boot/dts/marvell/kirkwood-dreamplug.dts
index 328516351e84..590bee3c561c 100644
--- a/arch/arm/boot/dts/kirkwood-dreamplug.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-dreamplug.dts
@@ -85,15 +85,15 @@
 			     &pmx_led_wifi_ap >;
 		pinctrl-names = "default";
 
-		bluetooth {
+		led-bluetooth {
 			label = "dreamplug:blue:bluetooth";
 			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
 		};
-		wifi {
+		led-wifi {
 			label = "dreamplug:green:wifi";
 			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
 		};
-		wifi-ap {
+		led-wifi-ap {
 			label = "dreamplug:green:wifi_ap";
 			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
 		};
diff --git a/arch/arm/boot/dts/kirkwood-ds109.dts b/arch/arm/boot/dts/marvell/kirkwood-ds109.dts
index 29982e7acb7f..29982e7acb7f 100644
--- a/arch/arm/boot/dts/kirkwood-ds109.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ds109.dts
diff --git a/arch/arm/boot/dts/kirkwood-ds110jv10.dts b/arch/arm/boot/dts/marvell/kirkwood-ds110jv10.dts
index d68c616e9309..d68c616e9309 100644
--- a/arch/arm/boot/dts/kirkwood-ds110jv10.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ds110jv10.dts
diff --git a/arch/arm/boot/dts/kirkwood-ds111.dts b/arch/arm/boot/dts/marvell/kirkwood-ds111.dts
index e1420cbcd7e4..e1420cbcd7e4 100644
--- a/arch/arm/boot/dts/kirkwood-ds111.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ds111.dts
diff --git a/arch/arm/boot/dts/kirkwood-ds112.dts b/arch/arm/boot/dts/marvell/kirkwood-ds112.dts
index f48609e95afe..3912f1b525b6 100644
--- a/arch/arm/boot/dts/kirkwood-ds112.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ds112.dts
@@ -43,7 +43,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie1 {
diff --git a/arch/arm/boot/dts/kirkwood-ds209.dts b/arch/arm/boot/dts/marvell/kirkwood-ds209.dts
index f41fe95e055f..f41fe95e055f 100644
--- a/arch/arm/boot/dts/kirkwood-ds209.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ds209.dts
diff --git a/arch/arm/boot/dts/kirkwood-ds210.dts b/arch/arm/boot/dts/marvell/kirkwood-ds210.dts
index 729f959a7838..729f959a7838 100644
--- a/arch/arm/boot/dts/kirkwood-ds210.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ds210.dts
diff --git a/arch/arm/boot/dts/kirkwood-ds212.dts b/arch/arm/boot/dts/marvell/kirkwood-ds212.dts
index 416bab50d170..416bab50d170 100644
--- a/arch/arm/boot/dts/kirkwood-ds212.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ds212.dts
diff --git a/arch/arm/boot/dts/kirkwood-ds212j.dts b/arch/arm/boot/dts/marvell/kirkwood-ds212j.dts
index 14cf4d8afaf3..14cf4d8afaf3 100644
--- a/arch/arm/boot/dts/kirkwood-ds212j.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ds212j.dts
diff --git a/arch/arm/boot/dts/kirkwood-ds409.dts b/arch/arm/boot/dts/marvell/kirkwood-ds409.dts
index a8650f9e3eb7..a8650f9e3eb7 100644
--- a/arch/arm/boot/dts/kirkwood-ds409.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ds409.dts
diff --git a/arch/arm/boot/dts/kirkwood-ds409slim.dts b/arch/arm/boot/dts/marvell/kirkwood-ds409slim.dts
index 27a1d840bd15..27a1d840bd15 100644
--- a/arch/arm/boot/dts/kirkwood-ds409slim.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ds409slim.dts
diff --git a/arch/arm/boot/dts/kirkwood-ds411.dts b/arch/arm/boot/dts/marvell/kirkwood-ds411.dts
index 86907be70cf9..1d4256ef325d 100644
--- a/arch/arm/boot/dts/kirkwood-ds411.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ds411.dts
@@ -47,7 +47,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie1 {
diff --git a/arch/arm/boot/dts/kirkwood-ds411j.dts b/arch/arm/boot/dts/marvell/kirkwood-ds411j.dts
index bb3200daea1e..bb3200daea1e 100644
--- a/arch/arm/boot/dts/kirkwood-ds411j.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ds411j.dts
diff --git a/arch/arm/boot/dts/kirkwood-ds411slim.dts b/arch/arm/boot/dts/marvell/kirkwood-ds411slim.dts
index 9c5364a4e0a8..9c5364a4e0a8 100644
--- a/arch/arm/boot/dts/kirkwood-ds411slim.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ds411slim.dts
diff --git a/arch/arm/boot/dts/kirkwood-goflexnet.dts b/arch/arm/boot/dts/marvell/kirkwood-goflexnet.dts
index d4cb3cd3e2a2..d5ac4e3974da 100644
--- a/arch/arm/boot/dts/kirkwood-goflexnet.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-goflexnet.dts
@@ -85,44 +85,44 @@
 			    >;
 		pinctrl-names = "default";
 
-		health {
+		led-health {
 			label = "status:green:health";
 			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
 			default-state = "keep";
 		};
-		fault {
+		led-fault {
 			label = "status:orange:fault";
 			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
 		};
-		left0 {
+		led-left0 {
 			label = "status:white:left0";
 			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
 		};
-		left1 {
+		led-left1 {
 			label = "status:white:left1";
 			gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
 		};
-		left2 {
+		led-left2 {
 			label = "status:white:left2";
 			gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
 		};
-		left3 {
+		led-left3 {
 			label = "status:white:left3";
 			gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
 		};
-		right0 {
+		led-right0 {
 			label = "status:white:right0";
 			gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
 		};
-		right1 {
+		led-right1 {
 			label = "status:white:right1";
 			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
 		};
-		right2 {
+		led-right2 {
 			label = "status:white:right2";
 			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
 		};
-		right3 {
+		led-right3 {
 			label = "status:white:right3";
 			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
 		};
diff --git a/arch/arm/boot/dts/kirkwood-guruplug-server-plus.dts b/arch/arm/boot/dts/marvell/kirkwood-guruplug-server-plus.dts
index dfb41393941d..d5aa8b505cc0 100644
--- a/arch/arm/boot/dts/kirkwood-guruplug-server-plus.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-guruplug-server-plus.dts
@@ -59,19 +59,19 @@
 			      &pmx_led_wmode_r &pmx_led_wmode_g >;
 		pinctrl-names = "default";
 
-		health-r {
+		led-health-r {
 			label = "guruplug:red:health";
 			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
 		};
-		health-g {
+		led-health-g {
 			label = "guruplug:green:health";
 			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
 		};
-		wmode-r {
+		led-wmode-r {
 			label = "guruplug:red:wmode";
 			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
 		};
-		wmode-g {
+		led-wmode-g {
 			label = "guruplug:green:wmode";
 			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
 		};
diff --git a/arch/arm/boot/dts/kirkwood-ib62x0.dts b/arch/arm/boot/dts/marvell/kirkwood-ib62x0.dts
index 962a910a6f5c..018c6b8f3e8a 100644
--- a/arch/arm/boot/dts/kirkwood-ib62x0.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ib62x0.dts
@@ -58,17 +58,15 @@
 
 	gpio_keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		pinctrl-0 = <&pmx_button_reset &pmx_button_usb_copy>;
 		pinctrl-names = "default";
 
-		copy {
+		button-copy {
 			label = "USB Copy";
 			linux,code = <KEY_COPY>;
 			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
 		};
-		reset {
+		button-reset {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio0 28 GPIO_ACTIVE_LOW>;
@@ -81,16 +79,16 @@
 			     &pmx_led_usb_transfer>;
 		pinctrl-names = "default";
 
-		green-os {
+		led-green-os {
 			label = "ib62x0:green:os";
 			gpios = <&gpio0 25 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
 		};
-		red-os {
+		led-red-os {
 			label = "ib62x0:red:os";
 			gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
 		};
-		usb-copy {
+		led-usb-copy {
 			label = "ib62x0:red:usb_copy";
 			gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>;
 		};
diff --git a/arch/arm/boot/dts/kirkwood-iconnect.dts b/arch/arm/boot/dts/marvell/kirkwood-iconnect.dts
index 95af7aa1fdcb..91b46e77e0b6 100644
--- a/arch/arm/boot/dts/kirkwood-iconnect.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-iconnect.dts
@@ -89,32 +89,32 @@
 			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 		};
-		power-blue {
+		led-power-blue {
 			label = "power:blue";
 			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
 		};
-		power-red {
+		led-power-red {
 			label = "power:red";
 			gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
 		};
-		usb1 {
+		led-usb1 {
 			label = "usb1:blue";
 			gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
 		};
-		usb2 {
+		led-usb2 {
 			label = "usb2:blue";
 			gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
 		};
-		usb3 {
+		led-usb3 {
 			label = "usb3:blue";
 			gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
 		};
-		usb4 {
+		led-usb4 {
 			label = "usb4:blue";
 			gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
 		};
-		otb {
+		led-otb {
 			label = "otb:blue";
 			gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
 		};
@@ -122,18 +122,16 @@
 
 	gpio_keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		pinctrl-0 = < &pmx_button_reset &pmx_button_otb >;
 		pinctrl-names = "default";
 
-		otb {
+		button-otb {
 			label = "OTB Button";
 			linux,code = <KEY_COPY>;
 			gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
 			debounce-interval = <100>;
 		};
-		reset {
+		button-reset {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
@@ -187,7 +185,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts b/arch/arm/boot/dts/marvell/kirkwood-iomega_ix2_200.dts
index 2338f495d517..039362152650 100644
--- a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-iomega_ix2_200.dts
@@ -127,44 +127,42 @@
 			      &pmx_led_rebuild &pmx_led_health >;
 		pinctrl-names = "default";
 
-		power_led {
+		led-power-led {
 			label = "status:white:power_led";
 			gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
 		};
-		rebuild_led {
+		led-rebuild-led {
 			label = "status:white:rebuild_led";
 			gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
 		};
-		health_led {
+		led-health-led {
 			label = "status:red:health_led";
 			gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
 		};
-		backup_led {
+		led-backup-led {
 			label = "status:blue:backup_led";
 			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
 		};
 	};
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		pinctrl-0 = <&pmx_button_reset &pmx_button_power
 			     &pmx_button_otb>;
 		pinctrl-names = "default";
 
 
-		Power {
+		button-power {
 			label = "Power Button";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
 		};
-		Reset {
+		button-reset {
 			label = "Reset Button";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
 		};
-		OTB {
+		button-otb {
 			label = "OTB Button";
 			linux,code = <KEY_COPY>;
 			gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/kirkwood-is2.dts b/arch/arm/boot/dts/marvell/kirkwood-is2.dts
index 1bc16a5cdbaa..1bc16a5cdbaa 100644
--- a/arch/arm/boot/dts/kirkwood-is2.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-is2.dts
diff --git a/arch/arm/boot/dts/kirkwood-km_common.dtsi b/arch/arm/boot/dts/marvell/kirkwood-km_common.dtsi
index 75dc83914f56..259cb3d5f16d 100644
--- a/arch/arm/boot/dts/kirkwood-km_common.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-km_common.dtsi
@@ -27,8 +27,8 @@
 
 	i2c {
 		compatible = "i2c-gpio";
-		gpios = < &gpio0 8 GPIO_ACTIVE_HIGH		/* sda */
-			  &gpio0 9 GPIO_ACTIVE_HIGH>;		/* scl */
+		sda-gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
+		scl-gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>;
 		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
 	};
 };
@@ -39,7 +39,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-km_fixedeth.dts b/arch/arm/boot/dts/marvell/kirkwood-km_fixedeth.dts
index 515be7bccc0a..515be7bccc0a 100644
--- a/arch/arm/boot/dts/kirkwood-km_fixedeth.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-km_fixedeth.dts
diff --git a/arch/arm/boot/dts/kirkwood-km_kirkwood.dts b/arch/arm/boot/dts/marvell/kirkwood-km_kirkwood.dts
index f035eff1c111..f035eff1c111 100644
--- a/arch/arm/boot/dts/kirkwood-km_kirkwood.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-km_kirkwood.dts
diff --git a/arch/arm/boot/dts/kirkwood-l-50.dts b/arch/arm/boot/dts/marvell/kirkwood-l-50.dts
index 0d81c43a6a73..974bc9de4702 100644
--- a/arch/arm/boot/dts/kirkwood-l-50.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-l-50.dts
@@ -62,9 +62,10 @@
 			status = "okay";
 			clock-frequency = <400000>;
 
-			gpio2: gpio-expander@20{
+			gpio2: gpio-expander@20 {
 				#gpio-cells = <2>;
 				#interrupt-cells = <2>;
+				interrupt-controller;
 				compatible = "semtech,sx1505q";
 				reg = <0x20>;
 
@@ -76,9 +77,10 @@
 			 * 5: mPCIE reset (active low)
 			 * 6: Express card reset (active low)
 			 */
-			gpio3: gpio-expander@21{
+			gpio3: gpio-expander@21 {
 				#gpio-cells = <2>;
 				#interrupt-cells = <2>;
+				interrupt-controller;
 				compatible = "semtech,sx1505q";
 				reg = <0x21>;
 
@@ -95,52 +97,52 @@
 	leds {
 		compatible = "gpio-leds";
 
-		status_green {
+		led-status-green {
 			label = "l-50:green:status";
 			gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
 		};
 
-		status_red {
+		led-status-red {
 			label = "l-50:red:status";
 			gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
 		};
 
-		wifi {
+		led-wifi {
 			label = "l-50:green:wifi";
 			gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "phy0tpt";
 		};
 
-		internet_green {
+		led-internet-green {
 			label = "l-50:green:internet";
 			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
 		};
 
-		internet_red {
+		led-internet-red {
 			label = "l-50:red:internet";
 			gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
 		};
 
-		usb1_green {
+		led-usb1-green {
 			label = "l-50:green:usb1";
 			gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "usbport";
 			trigger-sources = <&hub_port3>;
 		};
 
-		usb1_red {
+		led-usb1-red {
 			label = "l-50:red:usb1";
 			gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
 		};
 
-		usb2_green {
+		led-usb2-green {
 			label = "l-50:green:usb2";
 			gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "usbport";
 			trigger-sources = <&hub_port1>;
 		};
 
-		usb2_red {
+		led-usb2-red {
 			label = "l-50:red:usb2";
 			gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
 		};
@@ -191,7 +193,7 @@
 	keys {
 		compatible = "gpio-keys";
 
-		factory_defaults {
+		button-factory-defaults {
 			label = "factory_defaults";
 			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_RESTART>;
@@ -223,18 +225,18 @@
 			};
 
 			port@1 {
-			       reg = <1>;
-			       label = "lan1";
+				reg = <1>;
+				label = "lan1";
 			};
 
 			port@2 {
-			       reg = <2>;
-			       label = "lan6";
+				reg = <2>;
+				label = "lan6";
 			};
 
 			port@3 {
-			       reg = <3>;
-			       label = "lan2";
+				reg = <3>;
+				label = "lan2";
 			};
 
 			port@4 {
@@ -254,7 +256,6 @@
 
 			port@6 {
 				reg = <6>;
-				label = "cpu";
 				phy-mode = "rgmii-id";
 				ethernet = <&eth1port>;
 				fixed-link {
@@ -282,18 +283,18 @@
 			};
 
 			port@1 {
-			       reg = <1>;
-			       label = "lan8";
+				reg = <1>;
+				label = "lan8";
 			};
 
 			port@2 {
-			       reg = <2>;
-			       label = "lan4";
+				reg = <2>;
+				label = "lan4";
 			};
 
 			port@3 {
-			       reg = <3>;
-			       label = "dmz";
+				reg = <3>;
+				label = "dmz";
 			};
 
 			switch1port5: port@5 {
@@ -330,6 +331,7 @@
 	ethernet1-port@0 {
 		speed = <1000>;
 		duplex = <1>;
+		phy-mode = "rgmii";
 	};
 };
 
diff --git a/arch/arm/boot/dts/kirkwood-laplug.dts b/arch/arm/boot/dts/marvell/kirkwood-laplug.dts
index 6158214a939a..90ea6cdee8e0 100644
--- a/arch/arm/boot/dts/kirkwood-laplug.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-laplug.dts
@@ -51,7 +51,7 @@
 	gpio_keys {
 		compatible = "gpio-keys";
 
-		power {
+		button-power {
 			label = "Power push button";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
@@ -61,11 +61,11 @@
 	gpio-leds {
 		compatible = "gpio-leds";
 
-		red-fail {
+		led-red-fail {
 			label = "laplug_v2:red:power";
 			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
 		};
-		blue-power {
+		led-blue-power {
 			label = "laplug_v2:blue:power";
 			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
@@ -160,7 +160,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-linkstation-6282.dtsi b/arch/arm/boot/dts/marvell/kirkwood-linkstation-6282.dtsi
index 377b6e970259..dfac2045a1eb 100644
--- a/arch/arm/boot/dts/kirkwood-linkstation-6282.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-linkstation-6282.dtsi
@@ -118,10 +118,11 @@
 		gpios = <&gpio0 17 GPIO_ACTIVE_LOW
 			 &gpio0 16 GPIO_ACTIVE_LOW>;
 
-		gpio-fan,speed-map = <0 3
-				1500 2
-				3250 1
-				5000 0>;
+		gpio-fan,speed-map =
+				<   0 3>,
+				<1500 2>,
+				<3250 1>,
+				<5000 0>;
 
 		alarm-gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
 	};
diff --git a/arch/arm/boot/dts/kirkwood-linkstation-duo-6281.dtsi b/arch/arm/boot/dts/marvell/kirkwood-linkstation-duo-6281.dtsi
index ba629e02ba31..ba629e02ba31 100644
--- a/arch/arm/boot/dts/kirkwood-linkstation-duo-6281.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-linkstation-duo-6281.dtsi
diff --git a/arch/arm/boot/dts/kirkwood-linkstation-lsqvl.dts b/arch/arm/boot/dts/marvell/kirkwood-linkstation-lsqvl.dts
index 8bb381088910..8bb381088910 100644
--- a/arch/arm/boot/dts/kirkwood-linkstation-lsqvl.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-linkstation-lsqvl.dts
diff --git a/arch/arm/boot/dts/kirkwood-linkstation-lsvl.dts b/arch/arm/boot/dts/marvell/kirkwood-linkstation-lsvl.dts
index 3f2a0bfe03ed..3f2a0bfe03ed 100644
--- a/arch/arm/boot/dts/kirkwood-linkstation-lsvl.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-linkstation-lsvl.dts
diff --git a/arch/arm/boot/dts/kirkwood-linkstation-lswsxl.dts b/arch/arm/boot/dts/marvell/kirkwood-linkstation-lswsxl.dts
index c42d0da38fe7..c42d0da38fe7 100644
--- a/arch/arm/boot/dts/kirkwood-linkstation-lswsxl.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-linkstation-lswsxl.dts
diff --git a/arch/arm/boot/dts/kirkwood-linkstation-lswvl.dts b/arch/arm/boot/dts/marvell/kirkwood-linkstation-lswvl.dts
index e0f62adc0d5d..e0f62adc0d5d 100644
--- a/arch/arm/boot/dts/kirkwood-linkstation-lswvl.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-linkstation-lswvl.dts
diff --git a/arch/arm/boot/dts/kirkwood-linkstation-lswxl.dts b/arch/arm/boot/dts/marvell/kirkwood-linkstation-lswxl.dts
index c6024b569423..0425df8cb91c 100644
--- a/arch/arm/boot/dts/kirkwood-linkstation-lswxl.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-linkstation-lswxl.dts
@@ -69,10 +69,11 @@
 		gpios = <&gpio1 16 GPIO_ACTIVE_LOW
 			 &gpio1 15 GPIO_ACTIVE_LOW>;
 
-		gpio-fan,speed-map = <0 3
-				1500 2
-				3250 1
-				5000 0>;
+		gpio-fan,speed-map =
+				<   0 3>,
+				<1500 2>,
+				<3250 1>,
+				<5000 0>;
 
 		alarm-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
 	};
diff --git a/arch/arm/boot/dts/kirkwood-linkstation.dtsi b/arch/arm/boot/dts/marvell/kirkwood-linkstation.dtsi
index 407d6d8b3a7f..8a11d2b9d449 100644
--- a/arch/arm/boot/dts/kirkwood-linkstation.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-linkstation.dtsi
@@ -88,8 +88,6 @@
 
 	gpio_keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		pinctrl-0 = <&pmx_button_function &pmx_power_switch
 			     &pmx_power_auto_switch>;
 		pinctrl-names = "default";
@@ -156,7 +154,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-linksys-viper.dts b/arch/arm/boot/dts/marvell/kirkwood-linksys-viper.dts
index 2f9660f3b457..8a1c38ab6111 100644
--- a/arch/arm/boot/dts/kirkwood-linksys-viper.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-linksys-viper.dts
@@ -33,18 +33,16 @@
 
 	gpio_keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		pinctrl-0 = < &pmx_btn_wps &pmx_btn_reset >;
 		pinctrl-names = "default";
 
-		wps {
+		button-wps {
 			label = "WPS Button";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
 		};
 
-		reset {
+		button-reset {
 			label = "Reset Button";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
@@ -56,12 +54,12 @@
 		pinctrl-0 = < &pmx_led_white_health &pmx_led_white_pulse >;
 		pinctrl-names = "default";
 
-		white-health {
+		led-white-health {
 			label = "viper:white:health";
 			gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
 		};
 
-		white-pulse {
+		led-white-pulse {
 			label = "viper:white:pulse";
 			gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
 		};
@@ -198,7 +196,7 @@
 
 			port@5 {
 				reg = <5>;
-				label = "cpu";
+				phy-mode = "rgmii-id";
 				ethernet = <&eth0port>;
 				fixed-link {
 					speed = <1000>;
@@ -221,6 +219,7 @@
 	ethernet0-port@0 {
 		speed = <1000>;
 		duplex = <1>;
+		phy-mode = "rgmii";
 	};
 };
 
diff --git a/arch/arm/boot/dts/kirkwood-lschlv2.dts b/arch/arm/boot/dts/marvell/kirkwood-lschlv2.dts
index 1d737d903f5f..1d737d903f5f 100644
--- a/arch/arm/boot/dts/kirkwood-lschlv2.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-lschlv2.dts
diff --git a/arch/arm/boot/dts/kirkwood-lsxhl.dts b/arch/arm/boot/dts/marvell/kirkwood-lsxhl.dts
index a56e0d797778..a56e0d797778 100644
--- a/arch/arm/boot/dts/kirkwood-lsxhl.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-lsxhl.dts
diff --git a/arch/arm/boot/dts/kirkwood-lsxl.dtsi b/arch/arm/boot/dts/marvell/kirkwood-lsxl.dtsi
index 7b151acb9984..5e0b139dd4fb 100644
--- a/arch/arm/boot/dts/kirkwood-lsxl.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-lsxl.dtsi
@@ -10,6 +10,11 @@
 
 	ocp@f1000000 {
 		pinctrl: pin-controller@10000 {
+			/* Non-default UART pins */
+			pmx_uart0: pmx-uart0 {
+				marvell,pins = "mpp4", "mpp5";
+			};
+
 			pmx_power_hdd: pmx-power-hdd {
 				marvell,pins = "mpp10";
 				marvell,function = "gpo";
@@ -102,24 +107,22 @@
 
 	gpio_keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		pinctrl-0 = <&pmx_button_function &pmx_power_switch
 			     &pmx_power_auto_switch>;
 		pinctrl-names = "default";
 
-		option {
+		button-option {
 			label = "Function Button";
 			linux,code = <KEY_OPTION>;
 			gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
 		};
-		reserved {
+		button-reserved {
 			label = "Power-on Switch";
 			linux,code = <KEY_RESERVED>;
 			linux,input-type = <5>;
 			gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
 		};
-		power {
+		button-power {
 			label = "Power-auto Switch";
 			linux,code = <KEY_ESC>;
 			linux,input-type = <5>;
@@ -134,28 +137,28 @@
 			     &pmx_led_function_blue>;
 		pinctrl-names = "default";
 
-		func_blue {
+		led-func-blue {
 			label = "lsxl:blue:func";
 			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
 		};
 
-		alarm {
+		led-alarm {
 			label = "lsxl:red:alarm";
 			gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
 		};
 
-		info {
+		led-info {
 			label = "lsxl:amber:info";
 			gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
 		};
 
-		power {
+		led-power {
 			label = "lsxl:blue:power";
 			gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
 			default-state = "keep";
 		};
 
-		func_red {
+		led-func-red {
 			label = "lsxl:red:func";
 			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
 		};
@@ -167,10 +170,11 @@
 		pinctrl-names = "default";
 		gpios = <&gpio0 19 GPIO_ACTIVE_LOW
 		         &gpio0 18 GPIO_ACTIVE_LOW>;
-		gpio-fan,speed-map = <0    3
-		                      1500 2
-		                      3250 1
-		                      5000 0>;
+		gpio-fan,speed-map =
+				<0    3>,
+				<1500 2>,
+				<3250 1>,
+				<5000 0>;
 		alarm-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
 	};
 
@@ -213,22 +217,11 @@
 &mdio {
 	status = "okay";
 
-	ethphy0: ethernet-phy@0 {
-		reg = <0>;
-	};
-
 	ethphy1: ethernet-phy@8 {
 		reg = <8>;
 	};
 };
 
-&eth0 {
-	status = "okay";
-	ethernet0-port@0 {
-		phy-handle = <&ethphy0>;
-	};
-};
-
 &eth1 {
 	status = "okay";
 	ethernet1-port@0 {
diff --git a/arch/arm/boot/dts/kirkwood-mplcec4.dts b/arch/arm/boot/dts/marvell/kirkwood-mplcec4.dts
index b80d12f6aa49..6533b49a15b2 100644
--- a/arch/arm/boot/dts/kirkwood-mplcec4.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-mplcec4.dts
@@ -8,10 +8,10 @@
 	model = "MPL CEC4";
 	compatible = "mpl,cec4-10", "mpl,cec4", "marvell,kirkwood-88f6281", "marvell,kirkwood";
 
-        memory {
-                device_type = "memory";
-                reg = <0x00000000 0x20000000>;
-        };
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>;
+	};
 
 	chosen {
 		bootargs = "console=ttyS0,115200n8 earlyprintk";
@@ -66,8 +66,8 @@
 			};
 		};
 
-                i2c@11000 {
-                        status = "okay";
+		i2c@11000 {
+			status = "okay";
 
 			rtc@51 {
 				compatible = "nxp,pcf8563";
@@ -79,7 +79,7 @@
 				reg = <0x57>;
 			};
 
-                };
+		};
 
 		serial@12000 {
 			status = "okay";
@@ -114,36 +114,36 @@
 			    >;
 		pinctrl-names = "default";
 
-		health {
+		led-health {
 			label = "status:green:health";
 			gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
 		};
 
-		user1o {
+		led-user1o {
 			label = "user1:orange";
 			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
 			default-state = "on";
 		};
 
-		user1g {
+		led-user1g {
 			label = "user1:green";
 			gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
 			default-state = "on";
 		};
 
-		user0o {
+		led-user0o {
 			label = "user0:orange";
 			gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
 			default-state = "on";
 		};
 
-		user0g {
+		led-user0g {
 			label = "user0:green";
 			gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
 			default-state = "on";
 		};
 
-		misc {
+		led-misc {
 			label = "status:orange:misc";
 			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
 			default-state = "on";
@@ -208,7 +208,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts b/arch/arm/boot/dts/marvell/kirkwood-mv88f6281gtw-ge.dts
index 2e1a75348908..051579fc36b8 100644
--- a/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-mv88f6281gtw-ge.dts
@@ -63,7 +63,7 @@
 			status = "okay";
 		};
 
-		ehci@50000 {
+		usb@50000 {
 			status = "okay";
 		};
 	};
@@ -73,17 +73,17 @@
 		pinctrl-0 = <&pmx_leds &pmx_usb_led>;
 		pinctrl-names = "default";
 
-		green-status {
+		led-green-status {
 			label = "gtw:green:Status";
 			gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
 		};
 
-		red-status {
+		led-red-status {
 			label = "gtw:red:Status";
 			gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>;
 		};
 
-		green-usb {
+		led-green-usb {
 			label = "gtw:green:USB";
 			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
 		};
@@ -91,17 +91,15 @@
 
 	gpio_keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		pinctrl-0 = <&pmx_keys>;
 		pinctrl-names = "default";
 
-		restart {
+		button-restart {
 			label = "SWR Button";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
 		};
-		wps {
+		button-wps {
 			label = "WPS Button";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
@@ -149,7 +147,7 @@
 
 			port@5 {
 				reg = <5>;
-				label = "cpu";
+				phy-mode = "rgmii-id";
 				ethernet = <&eth0port>;
 				fixed-link {
 					speed = <1000>;
@@ -166,11 +164,12 @@
 	ethernet0-port@0 {
 		speed = <1000>;
 		duplex = <1>;
+		phy-mode = "rgmii";
 	};
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-nas2big.dts b/arch/arm/boot/dts/marvell/kirkwood-nas2big.dts
index 6a2934b7d0ce..0b0a15093146 100644
--- a/arch/arm/boot/dts/kirkwood-nas2big.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-nas2big.dts
@@ -131,7 +131,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-net2big.dts b/arch/arm/boot/dts/marvell/kirkwood-net2big.dts
index 3e3ac289e5b0..d5f6bb50ba11 100644
--- a/arch/arm/boot/dts/kirkwood-net2big.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-net2big.dts
@@ -46,11 +46,11 @@
 	};
 
 	clocks {
-	       g762_clk: g762-oscillator {
-			 compatible = "fixed-clock";
-			 #clock-cells = <0>;
-			 clock-frequency = <32768>;
-	       };
+		g762_clk: g762-oscillator {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/kirkwood-net5big.dts b/arch/arm/boot/dts/marvell/kirkwood-net5big.dts
index cba8a2b6f6d9..2497ad26b5b6 100644
--- a/arch/arm/boot/dts/kirkwood-net5big.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-net5big.dts
@@ -78,11 +78,11 @@
 	};
 
 	clocks {
-	       g762_clk: g762-oscillator {
-			 compatible = "fixed-clock";
-			 #clock-cells = <0>;
-			 clock-frequency = <32768>;
-	       };
+		g762_clk: g762-oscillator {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
 	};
 
 	netxbig-leds {
diff --git a/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts b/arch/arm/boot/dts/marvell/kirkwood-netgear_readynas_duo_v2.dts
index cb564c3bcdc4..cb564c3bcdc4 100644
--- a/arch/arm/boot/dts/kirkwood-netgear_readynas_duo_v2.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-netgear_readynas_duo_v2.dts
diff --git a/arch/arm/boot/dts/kirkwood-netgear_readynas_nv+_v2.dts b/arch/arm/boot/dts/marvell/kirkwood-netgear_readynas_nv+_v2.dts
index b13aee570804..6cf76430cfab 100644
--- a/arch/arm/boot/dts/kirkwood-netgear_readynas_nv+_v2.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-netgear_readynas_nv+_v2.dts
@@ -78,11 +78,11 @@
 		};
 
 		clocks {
-		       g762_clk: g762-oscillator {
-				 compatible = "fixed-clock";
-				 #clock-cells = <0>;
-				 clock-frequency = <8192>;
-		       };
+			g762_clk: g762-oscillator {
+				compatible = "fixed-clock";
+				#clock-cells = <0>;
+				clock-frequency = <8192>;
+			};
 		};
 
 		i2c@11000 {
@@ -266,7 +266,7 @@
 
 /* Connected to NEC uPD720200 USB 3.0 controller */
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-netxbig.dtsi b/arch/arm/boot/dts/marvell/kirkwood-netxbig.dtsi
index b5737026e244..d4edf2727388 100644
--- a/arch/arm/boot/dts/kirkwood-netxbig.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-netxbig.dtsi
@@ -53,26 +53,24 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
 		/*
 		 * esc and power represent a three position rocker
 		 * switch. Thus the conventional KEY_POWER does not fit
 		 */
-		exc {
+		button-exc {
 			label = "Back power switch (on|auto)";
 			linux,code = <KEY_ESC>;
 			linux,input-type = <5>;
 			gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
 		};
-		power {
+		button-power {
 			label = "Back power switch (auto|off)";
 			linux,code = <KEY_1>;
 			linux,input-type = <5>;
 			gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
 		};
-		option {
+		button-option {
 			label = "Function button";
 			linux,code = <KEY_OPTION>;
 			gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/kirkwood-ns2-common.dtsi b/arch/arm/boot/dts/marvell/kirkwood-ns2-common.dtsi
index 51530ea86622..d6b615cf6390 100644
--- a/arch/arm/boot/dts/kirkwood-ns2-common.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-ns2-common.dtsi
@@ -55,10 +55,8 @@
 
 	gpio_keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		power {
+		button-power {
 			label = "Power push button";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
@@ -68,7 +66,7 @@
 	gpio-leds {
 		compatible = "gpio-leds";
 
-		red-fail {
+		led-red-fail {
 			label = "ns2:red:fail";
 			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
 		};
diff --git a/arch/arm/boot/dts/kirkwood-ns2.dts b/arch/arm/boot/dts/marvell/kirkwood-ns2.dts
index 7b67083e1ec0..7b67083e1ec0 100644
--- a/arch/arm/boot/dts/kirkwood-ns2.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ns2.dts
diff --git a/arch/arm/boot/dts/kirkwood-ns2lite.dts b/arch/arm/boot/dts/marvell/kirkwood-ns2lite.dts
index b0cb5907ed63..686bcd6f0f3c 100644
--- a/arch/arm/boot/dts/kirkwood-ns2lite.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ns2lite.dts
@@ -24,7 +24,7 @@
 	gpio-leds {
 		compatible = "gpio-leds";
 
-		blue-sata {
+		led-blue-sata {
 			label = "ns2:blue:sata";
 			gpios = <&gpio0 30 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "disk-activity";
diff --git a/arch/arm/boot/dts/kirkwood-ns2max.dts b/arch/arm/boot/dts/marvell/kirkwood-ns2max.dts
index c0a087e77408..044958bc55da 100644
--- a/arch/arm/boot/dts/kirkwood-ns2max.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ns2max.dts
@@ -29,15 +29,15 @@
 			 &gpio1  1 GPIO_ACTIVE_LOW
 			 &gpio0 23 GPIO_ACTIVE_LOW>;
 		gpio-fan,speed-map =
-			<   0  0
-			 1500 15
-			 1700 14
-			 1800 13
-			 2100 12
-			 3100 11
-			 3300 10
-			 4300  9
-			 5500  8>;
+			<   0  0>,
+			<1500 15>,
+			<1700 14>,
+			<1800 13>,
+			<2100 12>,
+			<3100 11>,
+			<3300 10>,
+			<4300  9>,
+			<5500  8>;
 		alarm-gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
 	};
 
diff --git a/arch/arm/boot/dts/kirkwood-ns2mini.dts b/arch/arm/boot/dts/marvell/kirkwood-ns2mini.dts
index 5b9fa14b6428..3fbe008f9141 100644
--- a/arch/arm/boot/dts/kirkwood-ns2mini.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ns2mini.dts
@@ -30,15 +30,15 @@
 			 &gpio1  1 GPIO_ACTIVE_LOW
 			 &gpio0 23 GPIO_ACTIVE_LOW>;
 		gpio-fan,speed-map =
-			<   0  0
-			 3000 15
-			 3180 14
-			 4140 13
-			 4570 12
-			 6760 11
-			 7140 10
-			 7980  9
-			 9200  8>;
+			<   0  0>,
+			<3000 15>,
+			<3180 14>,
+			<4140 13>,
+			<4570 12>,
+			<6760 11>,
+			<7140 10>,
+			<7980  9>,
+			<9200  8>;
 		alarm-gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
 	};
 
diff --git a/arch/arm/boot/dts/kirkwood-nsa310.dts b/arch/arm/boot/dts/marvell/kirkwood-nsa310.dts
index 9b861c2e76c5..3555ac1c3b15 100644
--- a/arch/arm/boot/dts/kirkwood-nsa310.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-nsa310.dts
@@ -87,43 +87,43 @@
 			     &pmx_led_hdd_green &pmx_led_hdd_red>;
 		pinctrl-names = "default";
 
-		green-sys {
+		led-green-sys {
 			label = "nsa310:green:sys";
 			gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
 		};
-		red-sys {
+		led-red-sys {
 			label = "nsa310:red:sys";
 			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
 		};
-		green-hdd {
+		led-green-hdd {
 			label = "nsa310:green:hdd";
 			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
 		};
-		red-hdd {
+		led-red-hdd {
 			label = "nsa310:red:hdd";
 			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
 		};
-		green-esata {
+		led-green-esata {
 			label = "nsa310:green:esata";
 			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
 		};
-		red-esata {
+		led-red-esata {
 			label = "nsa310:red:esata";
 			gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
 		};
-		green-usb {
+		led-green-usb {
 			label = "nsa310:green:usb";
 			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
 		};
-		red-usb {
+		led-red-usb {
 			label = "nsa310:red:usb";
 			gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
 		};
-		green-copy {
+		led-green-copy {
 			label = "nsa310:green:copy";
 			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
 		};
-		red-copy {
+		led-red-copy {
 			label = "nsa310:red:copy";
 			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
 		};
@@ -131,7 +131,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-nsa310a.dts b/arch/arm/boot/dts/marvell/kirkwood-nsa310a.dts
index b85e314f045a..ddf84092aade 100644
--- a/arch/arm/boot/dts/kirkwood-nsa310a.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-nsa310a.dts
@@ -75,39 +75,39 @@
 	gpio-leds {
 		compatible = "gpio-leds";
 
-		green-sys {
+		led-green-sys {
 			label = "nsa310:green:sys";
 			gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
 		};
-		red-sys {
+		led-red-sys {
 			label = "nsa310:red:sys";
 			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
 		};
-		green-hdd {
+		led-green-hdd {
 			label = "nsa310:green:hdd";
 			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
 		};
-		red-hdd {
+		led-red-hdd {
 			label = "nsa310:red:hdd";
 			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
 		};
-		green-esata {
+		led-green-esata {
 			label = "nsa310:green:esata";
 			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
 		};
-		red-esata {
+		led-red-esata {
 			label = "nsa310:red:esata";
 			gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
 		};
-		green-usb {
+		led-green-usb {
 			label = "nsa310:green:usb";
 			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
 		};
-		green-copy {
+		led-green-copy {
 			label = "nsa310:green:copy";
 			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
 		};
-		red-copy {
+		led-red-copy {
 			label = "nsa310:red:copy";
 			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
 		};
diff --git a/arch/arm/boot/dts/marvell/kirkwood-nsa310s.dts b/arch/arm/boot/dts/marvell/kirkwood-nsa310s.dts
new file mode 100644
index 000000000000..47deb93c90a5
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/kirkwood-nsa310s.dts
@@ -0,0 +1,257 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * ZyXEL NSA310S Board Description
+ * Copyright 2020-2022 Pawel Dembicki <paweldembicki@gmail.com>
+ * Copyright (c) 2015-2021, Tony Dinh <mibodhi@gmail.com>
+ * Copyright (c) 2014, Adam Baker <linux@baker-net.org.uk>
+ * Based upon the board setup file created by Peter Schildmann
+ */
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "ZyXEL NSA310S";
+	compatible = "zyxel,nsa310s", "marvell,kirkwood-88f6702", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk";
+		stdout-path = &uart0;
+	};
+
+	gpio_poweroff {
+		compatible = "gpio-poweroff";
+		pinctrl-0 = <&pmx_pwr_off>;
+		pinctrl-names = "default";
+		gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&pmx_buttons>;
+		pinctrl-names = "default";
+
+		button-power {
+			label = "Power Button";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>;
+		};
+
+		button-copy {
+			label = "Copy Button";
+			linux,code = <KEY_COPY>;
+			gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
+		};
+
+		button-reset {
+			label = "Reset Button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&pmx_leds>;
+		pinctrl-names = "default";
+
+		led-1 {
+			function = LED_FUNCTION_DISK_ERR;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-2 {
+			function = LED_FUNCTION_USB;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "usb-host";
+		};
+
+		led-3 {
+			function = LED_FUNCTION_DISK;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "ata1";
+		};
+
+		led-4 {
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-5 {
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-6 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-7 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	usb0_power: regulator@1 {
+		compatible = "regulator-fixed";
+		regulator-name = "USB Power";
+
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>;
+	};
+
+	sata1_power: regulator@2 {
+		compatible = "regulator-fixed";
+		regulator-name = "SATA1 Power";
+
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+	};
+
+	thermal-zones {
+		disk-thermal {
+			polling-delay = <20000>;
+			polling-delay-passive = <2000>;
+
+			thermal-sensors = <&hdd_temp>;
+
+			trips {
+				disk_alert: disk-alert {
+					temperature = <40000>;
+					hysteresis = <5000>;
+					type = "active";
+				};
+				disk_crit: disk-crit {
+					temperature = <60000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
+
+&eth0 {
+	status = "okay";
+
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	rtc@68 {
+		compatible = "htk,ht1382";
+		reg = <0x68>;
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@1 {
+		reg = <1>;
+		phy-mode = "rgmii-id";
+		marvell,reg-init = <0x1 0x16 0x0 0x3>,
+				   <0x1 0x10 0x0 0x1017>,
+				   <0x1 0x11 0x0 0x4408>,
+				   <0x1 0x16 0x0 0x0>;
+	};
+};
+
+&nand {
+	status = "okay";
+	chip-delay = <35>;
+
+	partition@0 {
+		label = "uboot";
+		reg = <0x0000000 0x00c0000>;
+		read-only;
+	};
+	partition@c0000 {
+		label = "uboot_env";
+		reg = <0x00c0000 0x0080000>;
+	};
+	partition@140000 {
+		label = "ubi";
+		reg = <0x0140000 0x7ec0000>;
+	};
+};
+
+&pciec {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+
+	pmx_buttons: pmx-buttons {
+		marvell,pins = "mpp24", "mpp25", "mpp26";
+		marvell,function = "gpio";
+	};
+
+	pmx_leds: pmx-leds {
+		marvell,pins = "mpp13", "mpp15", "mpp16", "mpp22", "mpp23",
+						"mpp28", "mpp29";
+		marvell,function = "gpio";
+	};
+
+	pmx_power: pmx-power {
+		marvell,pins = "mpp21", "mpp33";
+		marvell,function = "gpio";
+	};
+
+	pmx_pwr_off: pmx-pwr-off {
+		marvell,pins = "mpp27";
+		marvell,function = "gpio";
+	};
+};
+
+&rtc {
+	status = "disabled";
+};
+
+&sata {
+	status = "okay";
+	nr-ports = <1>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	hdd_temp: sata-port@0 {
+		reg = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/kirkwood-nsa320.dts b/arch/arm/boot/dts/marvell/kirkwood-nsa320.dts
index b69b096f267b..dd5c8ffc8781 100644
--- a/arch/arm/boot/dts/kirkwood-nsa320.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-nsa320.dts
@@ -142,39 +142,39 @@
 			     &pmx_led_hdd1_green &pmx_led_hdd1_red>;
 		pinctrl-names = "default";
 
-		green-sys {
+		led-green-sys {
 			label = "nsa320:green:sys";
 			gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
 		};
-		orange-sys {
+		led-orange-sys {
 			label = "nsa320:orange:sys";
 			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
 		};
-		green-hdd1 {
+		led-green-hdd1 {
 			label = "nsa320:green:hdd1";
 			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
 		};
-		red-hdd1 {
+		led-red-hdd1 {
 			label = "nsa320:red:hdd1";
 			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
 		};
-		green-hdd2 {
+		led-green-hdd2 {
 			label = "nsa320:green:hdd2";
 			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
 		};
-		red-hdd2 {
+		led-red-hdd2 {
 			label = "nsa320:red:hdd2";
 			gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
 		};
-		green-usb {
+		led-green-usb {
 			label = "nsa320:green:usb";
 			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
 		};
-		green-copy {
+		led-green-copy {
 			label = "nsa320:green:copy";
 			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
 		};
-		red-copy {
+		led-red-copy {
 			label = "nsa320:red:copy";
 			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
 		};
@@ -211,7 +211,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-nsa325.dts b/arch/arm/boot/dts/marvell/kirkwood-nsa325.dts
index 6f8085dbb1f4..f0786a5f2ce6 100644
--- a/arch/arm/boot/dts/kirkwood-nsa325.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-nsa325.dts
@@ -162,39 +162,39 @@
 			     &pmx_led_hdd1_green &pmx_led_hdd1_red>;
 		pinctrl-names = "default";
 
-		green-sys {
+		led-green-sys {
 			label = "nsa325:green:sys";
 			gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
 		};
-		orange-sys {
+		led-orange-sys {
 			label = "nsa325:orange:sys";
 			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
 		};
-		green-hdd1 {
+		led-green-hdd1 {
 			label = "nsa325:green:hdd1";
 			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
 		};
-		red-hdd1 {
+		led-red-hdd1 {
 			label = "nsa325:red:hdd1";
 			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
 		};
-		green-hdd2 {
+		led-green-hdd2 {
 			label = "nsa325:green:hdd2";
 			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
 		};
-		red-hdd2 {
+		led-red-hdd2 {
 			label = "nsa325:red:hdd2";
 			gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
 		};
-		green-usb {
+		led-green-usb {
 			label = "nsa325:green:usb";
 			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
 		};
-		green-copy {
+		led-green-copy {
 			label = "nsa325:green:copy";
 			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
 		};
-		red-copy {
+		led-red-copy {
 			label = "nsa325:red:copy";
 			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
 		};
@@ -224,7 +224,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-nsa3x0-common.dtsi b/arch/arm/boot/dts/marvell/kirkwood-nsa3x0-common.dtsi
index 8f73197f251a..e9bd9c551af5 100644
--- a/arch/arm/boot/dts/kirkwood-nsa3x0-common.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-nsa3x0-common.dtsi
@@ -63,22 +63,20 @@
 
 	gpio_keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		pinctrl-0 = <&pmx_btn_reset &pmx_btn_copy &pmx_btn_power>;
 		pinctrl-names = "default";
 
-		power {
+		button-power {
 			label = "Power Button";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
 		};
-		copy {
+		button-copy {
 			label = "Copy Button";
 			linux,code = <KEY_COPY>;
 			gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
 		};
-		reset {
+		button-reset {
 			label = "Reset Button";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
@@ -150,7 +148,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-openblocks_a6.dts b/arch/arm/boot/dts/marvell/kirkwood-openblocks_a6.dts
index 8ea430168ea5..20c6290d2037 100644
--- a/arch/arm/boot/dts/kirkwood-openblocks_a6.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-openblocks_a6.dts
@@ -115,10 +115,8 @@
 		compatible = "gpio-keys";
 		pinctrl-0 = <&pmx_gpio_init>;
 		pinctrl-names = "default";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		power {
+		button-power {
 			label = "Init Button";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/kirkwood-openblocks_a7.dts b/arch/arm/boot/dts/marvell/kirkwood-openblocks_a7.dts
index 946f0f453dd1..2bc4b68bd723 100644
--- a/arch/arm/boot/dts/kirkwood-openblocks_a7.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-openblocks_a7.dts
@@ -44,7 +44,7 @@
 		i2c@11100 {
 			status = "okay";
 
-			s24c02: s24c02@50 {
+			s24c02: eeprom@50 {
 				compatible = "atmel,24c02";
 				reg = <0x50>;
 			};
@@ -136,8 +136,6 @@
 		compatible = "gpio-keys";
 		pinctrl-0 = <&pmx_gpio_init>;
 		pinctrl-names = "default";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
 		button {
 			label = "Init Button";
diff --git a/arch/arm/boot/dts/kirkwood-openrd-base.dts b/arch/arm/boot/dts/marvell/kirkwood-openrd-base.dts
index 094191ece3d7..094191ece3d7 100644
--- a/arch/arm/boot/dts/kirkwood-openrd-base.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-openrd-base.dts
diff --git a/arch/arm/boot/dts/kirkwood-openrd-client.dts b/arch/arm/boot/dts/marvell/kirkwood-openrd-client.dts
index d4e0b8150a84..cf26e2ceaaa0 100644
--- a/arch/arm/boot/dts/kirkwood-openrd-client.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-openrd-client.dts
@@ -38,7 +38,7 @@
 		simple-audio-card,mclk-fs = <256>;
 
 		simple-audio-card,cpu {
-			sound-dai = <&audio0 0>;
+			sound-dai = <&audio0>;
 		};
 
 		simple-audio-card,codec {
diff --git a/arch/arm/boot/dts/kirkwood-openrd-ultimate.dts b/arch/arm/boot/dts/marvell/kirkwood-openrd-ultimate.dts
index 888e13320c19..888e13320c19 100644
--- a/arch/arm/boot/dts/kirkwood-openrd-ultimate.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-openrd-ultimate.dts
diff --git a/arch/arm/boot/dts/kirkwood-openrd.dtsi b/arch/arm/boot/dts/marvell/kirkwood-openrd.dtsi
index 47f03c69c55a..9d7cff4feada 100644
--- a/arch/arm/boot/dts/kirkwood-openrd.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-openrd.dtsi
@@ -53,7 +53,7 @@
 			cd-gpios = <&gpio0 29 9>;
 		};
 		gpio@10100 {
-			p28 {
+			p28-hog {
 				gpio-hog;
 				gpios = <28 GPIO_ACTIVE_HIGH>;
 				/*
@@ -71,7 +71,7 @@
 			};
 		};
 		gpio@10140 {
-			p2 {
+			p2-hog {
 				gpio-hog;
 				gpios = <2 GPIO_ACTIVE_HIGH>;
 				/*
diff --git a/arch/arm/boot/dts/kirkwood-pogo_e02.dts b/arch/arm/boot/dts/marvell/kirkwood-pogo_e02.dts
index f9e95e55f36d..39a5345332da 100644
--- a/arch/arm/boot/dts/kirkwood-pogo_e02.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-pogo_e02.dts
@@ -33,12 +33,12 @@
 	gpio-leds {
 		compatible = "gpio-leds";
 
-		health {
+		led-health {
 			label = "pogo_e02:green:health";
 			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
 			default-state = "keep";
 		};
-		fault {
+		led-fault {
 			label = "pogo_e02:orange:fault";
 			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
 		};
diff --git a/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts b/arch/arm/boot/dts/marvell/kirkwood-pogoplug-series-4.dts
index 5aa4669ae254..0e9c4cf79822 100644
--- a/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-pogoplug-series-4.dts
@@ -29,12 +29,10 @@
 
 	gpio_keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		pinctrl-0 = <&pmx_button_eject>;
 		pinctrl-names = "default";
 
-		eject {
+		button-eject {
 			debounce-interval = <50>;
 			wakeup-source;
 			linux,code = <KEY_EJECTCD>;
@@ -48,12 +46,12 @@
 		pinctrl-0 = <&pmx_led_green &pmx_led_red>;
 		pinctrl-names = "default";
 
-		health {
+		led-health {
 			label = "pogoplugv4:green:health";
 			gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
 			default-state = "on";
 		};
-		fault {
+		led-fault {
 			label = "pogoplugv4:red:fault";
 			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
 		};
diff --git a/arch/arm/boot/dts/marvell/kirkwood-rd88f6192.dts b/arch/arm/boot/dts/marvell/kirkwood-rd88f6192.dts
new file mode 100644
index 000000000000..f00325ffde07
--- /dev/null
+++ b/arch/arm/boot/dts/marvell/kirkwood-rd88f6192.dts
@@ -0,0 +1,106 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Marvell RD88F6192 Board descrition
+ *
+ * Andrew Lunn <andrew@lunn.ch>
+ *
+ * This file contains the definitions that are common between the three
+ * variants of the Marvell Kirkwood Development Board.
+ */
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6192.dtsi"
+
+/ {
+	model = "Marvell RD88F6192 reference design";
+	compatible = "marvell,rd88f6192", "marvell,kirkwood-88f6192", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		stdout-path = &uart0;
+	};
+
+	ocp@f1000000 {
+		pinctrl: pin-controller@10000 {
+			pinctrl-0 = <&pmx_usb_power>;
+			pinctrl-names = "default";
+
+			pmx_usb_power: pmx-usb-power {
+				marvell,pins = "mpp10";
+				marvell,function = "gpo";
+			};
+		};
+
+		serial@12000 {
+			status = "okay";
+
+		};
+
+		spi@10600 {
+			status = "okay";
+
+			m25p128@0 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "st,m25p128", "jedec,spi-nor";
+				reg = <0>;
+				spi-max-frequency = <20000000>;
+				mode = <0>;
+			};
+		};
+
+		sata@80000 {
+			status = "okay";
+			nr-ports = <2>;
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_usb_power>;
+		pinctrl-names = "default";
+
+		usb_power: regulator@0 {
+			compatible = "regulator-fixed";
+			reg = <0>;
+			regulator-name = "USB VBUS";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 10 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@8 {
+		reg = <8>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
+};
+
+&pciec {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/kirkwood-rd88f6281-a.dts b/arch/arm/boot/dts/marvell/kirkwood-rd88f6281-a.dts
index 5da163591bbf..5da163591bbf 100644
--- a/arch/arm/boot/dts/kirkwood-rd88f6281-a.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-rd88f6281-a.dts
diff --git a/arch/arm/boot/dts/kirkwood-rd88f6281-z0.dts b/arch/arm/boot/dts/marvell/kirkwood-rd88f6281-z0.dts
index 9d88301daf0e..72edd47e19ff 100644
--- a/arch/arm/boot/dts/kirkwood-rd88f6281-z0.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-rd88f6281-z0.dts
@@ -19,7 +19,7 @@
 };
 
 &eth1 {
-      status = "disabled";
+	status = "disabled";
 };
 
 &switch {
diff --git a/arch/arm/boot/dts/kirkwood-rd88f6281.dtsi b/arch/arm/boot/dts/marvell/kirkwood-rd88f6281.dtsi
index f1f8eee132e8..9d62f910cddf 100644
--- a/arch/arm/boot/dts/kirkwood-rd88f6281.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-rd88f6281.dtsi
@@ -48,7 +48,7 @@
 			cd-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
 			/* No WP GPIO */
 		};
-       };
+	};
 };
 
 &nand {
@@ -105,7 +105,7 @@
 
 			port@5 {
 				reg = <5>;
-				label = "cpu";
+				phy-mode = "rgmii-id";
 				ethernet = <&eth0port>;
 				fixed-link {
 					speed = <1000>;
@@ -126,7 +126,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-rs212.dts b/arch/arm/boot/dts/marvell/kirkwood-rs212.dts
index c51cea883215..4ad412115a24 100644
--- a/arch/arm/boot/dts/kirkwood-rs212.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-rs212.dts
@@ -43,7 +43,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie1 {
diff --git a/arch/arm/boot/dts/kirkwood-rs409.dts b/arch/arm/boot/dts/marvell/kirkwood-rs409.dts
index 43673b03cb35..43673b03cb35 100644
--- a/arch/arm/boot/dts/kirkwood-rs409.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-rs409.dts
diff --git a/arch/arm/boot/dts/kirkwood-rs411.dts b/arch/arm/boot/dts/marvell/kirkwood-rs411.dts
index 41fa63cec839..41fa63cec839 100644
--- a/arch/arm/boot/dts/kirkwood-rs411.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-rs411.dts
diff --git a/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi b/arch/arm/boot/dts/marvell/kirkwood-sheevaplug-common.dtsi
index 0a698d3b7393..0a698d3b7393 100644
--- a/arch/arm/boot/dts/kirkwood-sheevaplug-common.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-sheevaplug-common.dtsi
diff --git a/arch/arm/boot/dts/kirkwood-sheevaplug-esata.dts b/arch/arm/boot/dts/marvell/kirkwood-sheevaplug-esata.dts
index ae8f493c9a0f..eb185273376e 100644
--- a/arch/arm/boot/dts/kirkwood-sheevaplug-esata.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-sheevaplug-esata.dts
@@ -33,7 +33,7 @@
 		pinctrl-0 = <&pmx_led_blue>;
 		pinctrl-names = "default";
 
-		health {
+		led-health {
 			label = "sheevaplug:blue:health";
 			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
 			default-state = "keep";
diff --git a/arch/arm/boot/dts/kirkwood-sheevaplug.dts b/arch/arm/boot/dts/marvell/kirkwood-sheevaplug.dts
index c73cc904e5c4..ce73fcf2255f 100644
--- a/arch/arm/boot/dts/kirkwood-sheevaplug.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-sheevaplug.dts
@@ -28,13 +28,13 @@
 		pinctrl-0 = <&pmx_led_blue &pmx_led_red>;
 		pinctrl-names = "default";
 
-		health {
+		led-health {
 			label = "sheevaplug:blue:health";
 			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
 			default-state = "keep";
 		};
 
-		misc {
+		led-misc {
 			label = "sheevaplug:red:misc";
 			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
 		};
diff --git a/arch/arm/boot/dts/kirkwood-synology.dtsi b/arch/arm/boot/dts/marvell/kirkwood-synology.dtsi
index 217bd374e52b..6b7c5218b1fb 100644
--- a/arch/arm/boot/dts/kirkwood-synology.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-synology.dtsi
@@ -198,7 +198,7 @@
 		spi@10600 {
 			status = "okay";
 
-			m25p80@0 {
+			flash@0 {
 				#address-cells = <1>;
 				#size-cells = <1>;
 				compatible = "st,m25p80", "jedec,spi-nor";
@@ -286,14 +286,15 @@
 		gpios = <&gpio1 0 GPIO_ACTIVE_HIGH
 			 &gpio1 1 GPIO_ACTIVE_HIGH
 			 &gpio1 2 GPIO_ACTIVE_HIGH>;
-		gpio-fan,speed-map = <    0 0
-				       2200 1
-				       2500 2
-				       3000 4
-				       3300 3
-				       3700 5
-				       3800 6
-				       4200 7 >;
+		gpio-fan,speed-map =
+				<   0 0>,
+				<2200 1>,
+				<2500 2>,
+				<3000 4>,
+				<3300 3>,
+				<3700 5>,
+				<3800 6>,
+				<4200 7>;
 	};
 
 	gpio-fan-150-15-18 {
@@ -306,14 +307,15 @@
 			 &gpio0 16 GPIO_ACTIVE_HIGH
 			 &gpio0 17 GPIO_ACTIVE_HIGH>;
 		alarm-gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>;
-		gpio-fan,speed-map = <    0 0
-				       2200 1
-				       2500 2
-				       3000 4
-				       3300 3
-				       3700 5
-				       3800 6
-				       4200 7 >;
+		gpio-fan,speed-map =
+				<   0 0>,
+				<2200 1>,
+				<2500 2>,
+				<3000 4>,
+				<3300 3>,
+				<3700 5>,
+				<3800 6>,
+				<4200 7>;
 	};
 
 	gpio-fan-100-32-35 {
@@ -326,14 +328,15 @@
 			 &gpio1 1 GPIO_ACTIVE_HIGH
 			 &gpio1 2 GPIO_ACTIVE_HIGH>;
 		alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
-		gpio-fan,speed-map = <    0 0
-				       2500 1
-				       3100 2
-				       3800 3
-				       4600 4
-				       4800 5
-				       4900 6
-				       5000 7 >;
+		gpio-fan,speed-map =
+				<   0 0>,
+				<2500 1>,
+				<3100 2>,
+				<3800 3>,
+				<4600 4>,
+				<4800 5>,
+				<4900 6>,
+				<5000 7>;
 	};
 
 	gpio-fan-100-15-18 {
@@ -346,14 +349,15 @@
 			 &gpio0 16 GPIO_ACTIVE_HIGH
 			 &gpio0 17 GPIO_ACTIVE_HIGH>;
 		alarm-gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>;
-		gpio-fan,speed-map = <    0 0
-				       2500 1
-				       3100 2
-				       3800 3
-				       4600 4
-				       4800 5
-				       4900 6
-				       5000 7 >;
+		gpio-fan,speed-map =
+				<   0 0>,
+				<2500 1>,
+				<3100 2>,
+				<3800 3>,
+				<4600 4>,
+				<4800 5>,
+				<4900 6>,
+				<5000 7>;
 	};
 
 	gpio-fan-100-15-35-1 {
@@ -366,14 +370,15 @@
 			 &gpio0 16 GPIO_ACTIVE_HIGH
 			 &gpio0 17 GPIO_ACTIVE_HIGH>;
 		alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
-		gpio-fan,speed-map = <    0 0
-				       2500 1
-				       3100 2
-				       3800 3
-				       4600 4
-				       4800 5
-				       4900 6
-				       5000 7 >;
+		gpio-fan,speed-map =
+				<   0 0>,
+				<2500 1>,
+				<3100 2>,
+				<3800 3>,
+				<4600 4>,
+				<4800 5>,
+				<4900 6>,
+				<5000 7>;
 	};
 
 	gpio-fan-100-15-35-3 {
@@ -388,14 +393,15 @@
 		alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH
 			       &gpio1 12 GPIO_ACTIVE_HIGH
 			       &gpio1 13 GPIO_ACTIVE_HIGH>;
-		gpio-fan,speed-map = <    0 0
-				       2500 1
-				       3100 2
-				       3800 3
-				       4600 4
-				       4800 5
-				       4900 6
-				       5000 7 >;
+		gpio-fan,speed-map =
+				<   0 0>,
+				<2500 1>,
+				<3100 2>,
+				<3800 3>,
+				<4600 4>,
+				<4800 5>,
+				<4900 6>,
+				<5000 7>;
 	};
 
 	gpio-leds-alarm-12 {
@@ -404,7 +410,7 @@
 		pinctrl-0 = <&pmx_alarmled_12>;
 		pinctrl-names = "default";
 
-		hdd1-green {
+		led-hdd1-green {
 			label = "synology:alarm";
 			gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
 		};
@@ -418,42 +424,42 @@
 			     &pmx_hddled_26 &pmx_hddled_27>;
 		pinctrl-names = "default";
 
-		hdd1-green {
+		led-hdd1-green {
 			label = "synology:green:hdd1";
 			gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
 		};
 
-		hdd1-amber {
+		led-hdd1-amber {
 			label = "synology:amber:hdd1";
 			gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
 		};
 
-		hdd2-green {
+		led-hdd2-green {
 			label = "synology:green:hdd2";
 			gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
 		};
 
-		hdd2-amber {
+		led-hdd2-amber {
 			label = "synology:amber:hdd2";
 			gpios = <&gpio0 23 GPIO_ACTIVE_LOW>;
 		};
 
-		hdd3-green {
+		led-hdd3-green {
 			label = "synology:green:hdd3";
 			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
 		};
 
-		hdd3-amber {
+		led-hdd3-amber {
 			label = "synology:amber:hdd3";
 			gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
 		};
 
-		hdd4-green {
+		led-hdd4-green {
 			label = "synology:green:hdd4";
 			gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
 		};
 
-		hdd4-amber {
+		led-hdd4-amber {
 			label = "synology:amber:hdd4";
 			gpios = <&gpio0 27 GPIO_ACTIVE_LOW>;
 		};
@@ -465,12 +471,12 @@
 		pinctrl-0 = <&pmx_hddled_21 &pmx_hddled_23>;
 		pinctrl-names = "default";
 
-		hdd1-green {
+		led-hdd1-green {
 			label = "synology:green:hdd1";
 			gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
 		};
 
-		hdd1-amber {
+		led-hdd1-amber {
 			label = "synology:amber:hdd1";
 			gpios = <&gpio0 23 GPIO_ACTIVE_LOW>;
 		};
@@ -482,22 +488,22 @@
 		pinctrl-0 = <&pmx_hddled_21 &pmx_hddled_23 &pmx_hddled_20 &pmx_hddled_22>;
 		pinctrl-names = "default";
 
-		hdd1-green {
+		led-hdd1-green {
 			label = "synology:green:hdd1";
 			gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
 		};
 
-		hdd1-amber {
+		led-hdd1-amber {
 			label = "synology:amber:hdd1";
 			gpios = <&gpio0 23 GPIO_ACTIVE_LOW>;
 		};
 
-		hdd2-green {
+		led-hdd2-green {
 			label = "synology:green:hdd2";
 			gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
 		};
 
-		hdd2-amber {
+		led-hdd2-amber {
 			label = "synology:amber:hdd2";
 			gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
 		};
@@ -512,52 +518,52 @@
 			     &pmx_hddled_45>;
 		pinctrl-names = "default";
 
-		hdd1-green {
+		led-hdd1-green {
 			label = "synology:green:hdd1";
 			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
 		};
 
-		hdd1-amber {
+		led-hdd1-amber {
 			label = "synology:amber:hdd1";
 			gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
 		};
 
-		hdd2-green {
+		led-hdd2-green {
 			label = "synology:green:hdd2";
 			gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
 		};
 
-		hdd2-amber {
+		led-hdd2-amber {
 			label = "synology:amber:hdd2";
 			gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
 		};
 
-		hdd3-green {
+		led-hdd3-green {
 			label = "synology:green:hdd3";
 			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
 		};
 
-		hdd3-amber {
+		led-hdd3-amber {
 			label = "synology:amber:hdd3";
 			gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
 		};
 
-		hdd4-green {
+		led-hdd4-green {
 			label = "synology:green:hdd4";
 			gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
 		};
 
-		hdd4-amber {
+		led-hdd4-amber {
 			label = "synology:amber:hdd4";
 			gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
 		};
 
-		hdd5-green {
+		led-hdd5-green {
 			label = "synology:green:hdd5";
 			gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
 		};
 
-		hdd5-amber {
+		led-hdd5-amber {
 			label = "synology:amber:hdd5";
 			gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
 		};
@@ -569,22 +575,22 @@
 		pinctrl-0 = <&pmx_hddled_38 &pmx_hddled_39 &pmx_hddled_36 &pmx_hddled_37>;
 		pinctrl-names = "default";
 
-		hdd1-green {
+		led-hdd1-green {
 			label = "synology:green:hdd1";
 			gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
 		};
 
-		hdd1-amber {
+		led-hdd1-amber {
 			label = "synology:amber:hdd1";
 			gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
 		};
 
-		hdd2-green {
+		led-hdd2-green {
 			label = "synology:green:hdd2";
 			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
 		};
 
-		hdd2-amber {
+		led-hdd2-amber {
 			label = "synology:amber:hdd2";
 			gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
 		};
@@ -847,7 +853,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-t5325.dts b/arch/arm/boot/dts/marvell/kirkwood-t5325.dts
index fe63b3a03a72..a6e77a487d00 100644
--- a/arch/arm/boot/dts/kirkwood-t5325.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-t5325.dts
@@ -156,12 +156,10 @@
 
 	gpio_keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		pinctrl-0 = <&pmx_button_power>;
 		pinctrl-names = "default";
 
-		power {
+		button-power {
 			label = "Power Button";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
@@ -219,7 +217,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-topkick.dts b/arch/arm/boot/dts/marvell/kirkwood-topkick.dts
index a5b51e29f63e..a5b51e29f63e 100644
--- a/arch/arm/boot/dts/kirkwood-topkick.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-topkick.dts
diff --git a/arch/arm/boot/dts/kirkwood-ts219-6281.dts b/arch/arm/boot/dts/marvell/kirkwood-ts219-6281.dts
index 30892c19aceb..a2e0ad4b84d8 100644
--- a/arch/arm/boot/dts/kirkwood-ts219-6281.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ts219-6281.dts
@@ -35,17 +35,15 @@
 
 	gpio_keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		pinctrl-0 = <&pmx_reset_button &pmx_USB_copy_button>;
 		pinctrl-names = "default";
 
-		copy {
+		button-copy {
 			label = "USB Copy";
 			linux,code = <KEY_COPY>;
 			gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
 		};
-		reset {
+		button-reset {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/kirkwood-ts219-6282.dts b/arch/arm/boot/dts/marvell/kirkwood-ts219-6282.dts
index aba1205981f1..35be6bce1dba 100644
--- a/arch/arm/boot/dts/kirkwood-ts219-6282.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ts219-6282.dts
@@ -35,17 +35,15 @@
 
 	gpio_keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		pinctrl-0 = <&pmx_reset_button &pmx_USB_copy_button>;
 		pinctrl-names = "default";
 
-		copy {
+		button-copy {
 			label = "USB Copy";
 			linux,code = <KEY_COPY>;
 			gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
 		};
-		reset {
+		button-reset {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/kirkwood-ts219.dtsi b/arch/arm/boot/dts/marvell/kirkwood-ts219.dtsi
index 994cabcf4b51..1939462a5f48 100644
--- a/arch/arm/boot/dts/kirkwood-ts219.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-ts219.dtsi
@@ -86,7 +86,7 @@
 	status = "okay";
 
 	ethphy0: ethernet-phy@X {
-                /* overwrite reg property in board file */
+		/* overwrite reg property in board file */
 	};
 };
 
@@ -98,7 +98,7 @@
 };
 
 &pciec {
-        status = "okay";
+	status = "okay";
 };
 
 &pcie0 {
diff --git a/arch/arm/boot/dts/kirkwood-ts419-6281.dts b/arch/arm/boot/dts/marvell/kirkwood-ts419-6281.dts
index 4a42ebcca4f0..4a42ebcca4f0 100644
--- a/arch/arm/boot/dts/kirkwood-ts419-6281.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ts419-6281.dts
diff --git a/arch/arm/boot/dts/kirkwood-ts419-6282.dts b/arch/arm/boot/dts/marvell/kirkwood-ts419-6282.dts
index be772e194c2b..be772e194c2b 100644
--- a/arch/arm/boot/dts/kirkwood-ts419-6282.dts
+++ b/arch/arm/boot/dts/marvell/kirkwood-ts419-6282.dts
diff --git a/arch/arm/boot/dts/kirkwood-ts419.dtsi b/arch/arm/boot/dts/marvell/kirkwood-ts419.dtsi
index 717236853e45..f136059607b7 100644
--- a/arch/arm/boot/dts/kirkwood-ts419.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood-ts419.dtsi
@@ -36,17 +36,15 @@
 
 	gpio_keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		pinctrl-0 = <&pmx_reset_button &pmx_USB_copy_button>;
 		pinctrl-names = "default";
 
-		copy {
+		button-copy {
 			label = "USB Copy";
 			linux,code = <KEY_COPY>;
 			gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
 		};
-		reset {
+		button-reset {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/marvell/kirkwood.dtsi
index fca31a5d5ac7..8a1338e672b3 100644
--- a/arch/arm/boot/dts/kirkwood.dtsi
+++ b/arch/arm/boot/dts/marvell/kirkwood.dtsi
@@ -24,9 +24,9 @@
 	};
 
 	aliases {
-	       gpio0 = &gpio0;
-	       gpio1 = &gpio1;
-	       i2c0 = &i2c0;
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+		i2c0 = &i2c0;
 	};
 
 	mbus@f1000000 {
@@ -263,7 +263,7 @@
 			status = "okay";
 		};
 
-		usb0: ehci@50000 {
+		usb0: usb@50000 {
 			compatible = "marvell,orion-ehci";
 			reg = <0x50000 0x1000>;
 			interrupts = <19>;
@@ -279,15 +279,15 @@
 			clocks = <&gate_clk 8>;
 
 			xor00 {
-			      interrupts = <5>;
-			      dmacap,memcpy;
-			      dmacap,xor;
+				interrupts = <5>;
+				dmacap,memcpy;
+				dmacap,xor;
 			};
 			xor01 {
-			      interrupts = <6>;
-			      dmacap,memcpy;
-			      dmacap,xor;
-			      dmacap,memset;
+				interrupts = <6>;
+				dmacap,memcpy;
+				dmacap,xor;
+				dmacap,memset;
 			};
 		};
 
@@ -299,15 +299,15 @@
 			clocks = <&gate_clk 16>;
 
 			xor00 {
-			      interrupts = <7>;
-			      dmacap,memcpy;
-			      dmacap,xor;
+				interrupts = <7>;
+				dmacap,memcpy;
+				dmacap,xor;
 			};
 			xor01 {
-			      interrupts = <8>;
-			      dmacap,memcpy;
-			      dmacap,xor;
-			      dmacap,memset;
+				interrupts = <8>;
+				dmacap,memcpy;
+				dmacap,xor;
+				dmacap,memset;
 			};
 		};
 
diff --git a/arch/arm/boot/dts/mmp2-brownstone.dts b/arch/arm/boot/dts/marvell/mmp2-brownstone.dts
index 04f1ae1382e7..bc64348b8218 100644
--- a/arch/arm/boot/dts/mmp2-brownstone.dts
+++ b/arch/arm/boot/dts/marvell/mmp2-brownstone.dts
@@ -28,7 +28,7 @@
 &twsi1 {
 	status = "okay";
 	pmic: max8925@3c {
-		compatible = "maxium,max8925";
+		compatible = "maxim,max8925";
 		reg = <0x3c>;
 		interrupts = <1>;
 		interrupt-parent = <&intcmux4>;
diff --git a/arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts b/arch/arm/boot/dts/marvell/mmp2-olpc-xo-1-75.dts
index 55ea87870af3..86c425b72fa7 100644
--- a/arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts
+++ b/arch/arm/boot/dts/marvell/mmp2-olpc-xo-1-75.dts
@@ -113,8 +113,8 @@
 			  "Headphones", "HPOR",
 			  "MIC2", "Mic Jack";
 		widgets = "Headphone", "Headphones", "Microphone", "Mic Jack";
-		hp-det-gpio = <&gpio 97 GPIO_ACTIVE_HIGH>;
-		mic-det-gpio = <&gpio 96 GPIO_ACTIVE_HIGH>;
+		hp-det-gpios = <&gpio 97 GPIO_ACTIVE_HIGH>;
+		mic-det-gpios = <&gpio 96 GPIO_ACTIVE_HIGH>;
 	};
 
 	soc {
diff --git a/arch/arm/boot/dts/mmp2.dtsi b/arch/arm/boot/dts/marvell/mmp2.dtsi
index 46984d4c5224..987d792f67ea 100644
--- a/arch/arm/boot/dts/mmp2.dtsi
+++ b/arch/arm/boot/dts/marvell/mmp2.dtsi
@@ -275,7 +275,9 @@
 				compatible = "marvell,pdma-1.0";
 				reg = <0xd4000000 0x10000>;
 				interrupts = <48>;
+				/* For backwards compatibility: */
 				#dma-channels = <16>;
+				dma-channels = <16>;
 				status = "disabled";
 			};
 
diff --git a/arch/arm/boot/dts/mmp3-dell-ariel.dts b/arch/arm/boot/dts/marvell/mmp3-dell-ariel.dts
index fe6df364a9eb..fe6df364a9eb 100644
--- a/arch/arm/boot/dts/mmp3-dell-ariel.dts
+++ b/arch/arm/boot/dts/marvell/mmp3-dell-ariel.dts
diff --git a/arch/arm/boot/dts/mmp3.dtsi b/arch/arm/boot/dts/marvell/mmp3.dtsi
index a4fb9203ec1f..a4fb9203ec1f 100644
--- a/arch/arm/boot/dts/mmp3.dtsi
+++ b/arch/arm/boot/dts/marvell/mmp3.dtsi
diff --git a/arch/arm/boot/dts/mvebu-linkstation-fan.dtsi b/arch/arm/boot/dts/marvell/mvebu-linkstation-fan.dtsi
index e172029a0c4d..a260c42dbda3 100644
--- a/arch/arm/boot/dts/mvebu-linkstation-fan.dtsi
+++ b/arch/arm/boot/dts/marvell/mvebu-linkstation-fan.dtsi
@@ -50,10 +50,10 @@
 		pinctrl-names = "default";
 
 		gpio-fan,speed-map =
-			<0		3
-			1500	2
-			3250	1
-			5000	0>;
+			<   0 3>,
+			<1500 2>,
+			<3250 1>,
+			<5000 0>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/mvebu-linkstation-gpio-simple.dtsi b/arch/arm/boot/dts/marvell/mvebu-linkstation-gpio-simple.dtsi
index c2d87ba6190a..055ac754c5fd 100644
--- a/arch/arm/boot/dts/mvebu-linkstation-gpio-simple.dtsi
+++ b/arch/arm/boot/dts/marvell/mvebu-linkstation-gpio-simple.dtsi
@@ -48,8 +48,6 @@
 / {
 	gpio_keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		pinctrl-0 = <&pmx_power_switch>;
 		pinctrl-names = "default";
 
diff --git a/arch/arm/boot/dts/orion5x-kuroboxpro.dts b/arch/arm/boot/dts/marvell/orion5x-kuroboxpro.dts
index e28b568e741a..e28b568e741a 100644
--- a/arch/arm/boot/dts/orion5x-kuroboxpro.dts
+++ b/arch/arm/boot/dts/marvell/orion5x-kuroboxpro.dts
diff --git a/arch/arm/boot/dts/orion5x-lacie-d2-network.dts b/arch/arm/boot/dts/marvell/orion5x-lacie-d2-network.dts
index 422958d13d42..12a4aac2633e 100644
--- a/arch/arm/boot/dts/orion5x-lacie-d2-network.dts
+++ b/arch/arm/boot/dts/marvell/orion5x-lacie-d2-network.dts
@@ -1,10 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
  * Copyright (C) 2009 Simon Guinot <sguinot@lacie.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 /dts-v1/;
@@ -38,22 +35,21 @@
 		compatible = "gpio-keys";
 		pinctrl-0 = <&pmx_buttons>;
 		pinctrl-names = "default";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		front_button {
+
+		button-front {
 			label = "Front Push Button";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>;
 		};
 
-		power_rocker_sw_on {
+		switch-power-rocker-sw-on {
 			label = "Power rocker switch (on|auto)";
 			linux,input-type = <5>; /* EV_SW */
 			linux,code = <1>; /* D2NET_SWITCH_POWER_ON */
 			gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
 		};
 
-		power_rocker_sw_off {
+		switch-power-rocker-sw-off {
 			label = "Power rocker switch (auto|off)";
 			linux,input-type = <5>; /* EV_SW */
 			linux,code = <2>; /* D2NET_SWITCH_POWER_OFF */
diff --git a/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts b/arch/arm/boot/dts/marvell/orion5x-lacie-ethernet-disk-mini-v2.dts
index 0043e0040153..f81acb9b7223 100644
--- a/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts
+++ b/arch/arm/boot/dts/marvell/orion5x-lacie-ethernet-disk-mini-v2.dts
@@ -1,10 +1,5 @@
-/*
- * Copyright (C) 2012 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2012 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
 
 /*
  * TODO: add Orion USB device port init when kernel.org support is added.
@@ -44,9 +39,8 @@
 		compatible = "gpio-keys";
 		pinctrl-0 = <&pmx_power_button>;
 		pinctrl-names = "default";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		button@1 {
+
+		button-1 {
 			label = "Power-on Switch";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>;
@@ -58,7 +52,7 @@
 		pinctrl-0 = <&pmx_power_led>;
 		pinctrl-names = "default";
 
-		led@1 {
+		led-1 {
 			label = "power:blue";
 			gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
 		};
diff --git a/arch/arm/boot/dts/orion5x-linkstation-lschl.dts b/arch/arm/boot/dts/marvell/orion5x-linkstation-lschl.dts
index ee751995c8d0..79fee048c900 100644
--- a/arch/arm/boot/dts/orion5x-linkstation-lschl.dts
+++ b/arch/arm/boot/dts/marvell/orion5x-linkstation-lschl.dts
@@ -61,7 +61,7 @@
 	};
 
 	gpio_keys {
-		func {
+		func-button {
 			label = "Function Button";
 			linux,code = <KEY_OPTION>;
 			gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
@@ -90,7 +90,7 @@
 			gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
 		};
 
-		func {
+		func-led {
 			label = "lschl:func:blue:top";
 			gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
 		};
diff --git a/arch/arm/boot/dts/orion5x-linkstation-lsgl.dts b/arch/arm/boot/dts/marvell/orion5x-linkstation-lsgl.dts
index 9f6fedd39170..9f6fedd39170 100644
--- a/arch/arm/boot/dts/orion5x-linkstation-lsgl.dts
+++ b/arch/arm/boot/dts/marvell/orion5x-linkstation-lsgl.dts
diff --git a/arch/arm/boot/dts/orion5x-linkstation-lswtgl.dts b/arch/arm/boot/dts/marvell/orion5x-linkstation-lswtgl.dts
index 7f77ce8cc1fc..7f77ce8cc1fc 100644
--- a/arch/arm/boot/dts/orion5x-linkstation-lswtgl.dts
+++ b/arch/arm/boot/dts/marvell/orion5x-linkstation-lswtgl.dts
diff --git a/arch/arm/boot/dts/orion5x-linkstation.dtsi b/arch/arm/boot/dts/marvell/orion5x-linkstation.dtsi
index b6c9b85951ea..b6c9b85951ea 100644
--- a/arch/arm/boot/dts/orion5x-linkstation.dtsi
+++ b/arch/arm/boot/dts/marvell/orion5x-linkstation.dtsi
diff --git a/arch/arm/boot/dts/orion5x-lswsgl.dts b/arch/arm/boot/dts/marvell/orion5x-lswsgl.dts
index 2fbc17d6dfa4..e0da406c430f 100644
--- a/arch/arm/boot/dts/orion5x-lswsgl.dts
+++ b/arch/arm/boot/dts/marvell/orion5x-lswsgl.dts
@@ -74,22 +74,21 @@
 		compatible = "gpio-keys";
 		pinctrl-0 = <&pmx_buttons>;
 		pinctrl-names = "default";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		func {
+
+		key-func {
 			label = "Function Button";
 			linux,code = <KEY_OPTION>;
 			gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
 		};
 
-		power {
+		key-power {
 			label = "Power-on Switch";
 			linux,input-type = <5>; /* EV_SW */
 			linux,code = <KEY_RESERVED>; /* LSMINI_SW_POWER */
 			gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
 		};
 
-		autopower {
+		key-autopower {
 			label = "Power-auto Switch";
 			linux,input-type = <5>; /* EV_SW */
 			linux,code = <KEY_ESC>; /* LSMINI_SW_AUTOPOWER */
@@ -103,24 +102,24 @@
 			     &pmx_led_power>;
 		pinctrl-names = "default";
 
-		alarm {
+		led-alarm {
 			label = "lswsgl:alarm:red";
-			gpio = <&gpio0 2 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
 		};
 
-		info {
+		led-info {
 			label = "lswsgl:info:amber";
-			gpio = <&gpio0 3 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
 		};
 
-		func {
+		led-func {
 			label = "lswsgl:func:blue:top";
-			gpio = <&gpio0 9 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
 		};
 
-		power {
+		led-power {
 			label = "lswsgl:power:blue:bottom";
-			gpio = <&gpio0 14 GPIO_ACTIVE_LOW>;
+			gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
 			default-state = "on";
 		};
 	};
diff --git a/arch/arm/boot/dts/orion5x-maxtor-shared-storage-2.dts b/arch/arm/boot/dts/marvell/orion5x-maxtor-shared-storage-2.dts
index 0ca6208a267d..cb1bd24b7ae3 100644
--- a/arch/arm/boot/dts/orion5x-maxtor-shared-storage-2.dts
+++ b/arch/arm/boot/dts/marvell/orion5x-maxtor-shared-storage-2.dts
@@ -1,10 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
  * Copyright (C) Sylver Bruneau <sylver.bruneau@googlemail.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 /dts-v1/;
@@ -38,15 +35,14 @@
 		compatible = "gpio-keys";
 		pinctrl-0 = <&pmx_buttons>;
 		pinctrl-names = "default";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		power {
+
+		key-power {
 			label = "Power";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
 		};
 
-		reset {
+		key-reset {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/orion5x-mv88f5181.dtsi b/arch/arm/boot/dts/marvell/orion5x-mv88f5181.dtsi
index f667012b26ca..819f9efb7058 100644
--- a/arch/arm/boot/dts/orion5x-mv88f5181.dtsi
+++ b/arch/arm/boot/dts/marvell/orion5x-mv88f5181.dtsi
@@ -1,10 +1,5 @@
-/*
- * Copyright (C) 2016 Jamie Lentin <jm@lentin.co.uk>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2016 Jamie Lentin <jm@lentin.co.uk>
 
 #include "orion5x.dtsi"
 
diff --git a/arch/arm/boot/dts/orion5x-mv88f5182.dtsi b/arch/arm/boot/dts/marvell/orion5x-mv88f5182.dtsi
index d1ed71c60209..86b87fb26dc9 100644
--- a/arch/arm/boot/dts/orion5x-mv88f5182.dtsi
+++ b/arch/arm/boot/dts/marvell/orion5x-mv88f5182.dtsi
@@ -1,10 +1,5 @@
-/*
- * Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
 
 #include "orion5x.dtsi"
 
diff --git a/arch/arm/boot/dts/orion5x-netgear-wnr854t.dts b/arch/arm/boot/dts/marvell/orion5x-netgear-wnr854t.dts
index ea081afa469d..d63ea15539aa 100644
--- a/arch/arm/boot/dts/orion5x-netgear-wnr854t.dts
+++ b/arch/arm/boot/dts/marvell/orion5x-netgear-wnr854t.dts
@@ -1,10 +1,5 @@
-/*
- * Copyright (C) 2016 Jamie Lentin <jm@lentin.co.uk>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2016 Jamie Lentin <jm@lentin.co.uk>
 
 /dts-v1/;
 
@@ -40,7 +35,7 @@
 		pinctrl-0 = <&pmx_reset_button>;
 		pinctrl-names = "default";
 
-		reset {
+		key-reset {
 			label = "Reset Button";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
@@ -142,8 +137,12 @@
 
 			port@3 {
 				reg = <3>;
-				label = "cpu";
 				ethernet = <&ethport>;
+				phy-mode = "rgmii-id";
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
 			};
 
 			port@5 {
@@ -213,6 +212,7 @@
 		/* Hardwired to DSA switch */
 		speed = <1000>;
 		duplex = <1>;
+		phy-mode = "rgmii";
 	};
 };
 
diff --git a/arch/arm/boot/dts/orion5x-rd88f5182-nas.dts b/arch/arm/boot/dts/marvell/orion5x-rd88f5182-nas.dts
index 487324f7c54e..75ab913b21e5 100644
--- a/arch/arm/boot/dts/orion5x-rd88f5182-nas.dts
+++ b/arch/arm/boot/dts/marvell/orion5x-rd88f5182-nas.dts
@@ -1,10 +1,5 @@
-/*
- * Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
 
 /dts-v1/;
 
@@ -37,7 +32,7 @@
 		pinctrl-0 = <&pmx_debug_led>;
 		pinctrl-names = "default";
 
-		led@0 {
+		led-0 {
 			label = "rd88f5182:cpu";
 			linux,default-trigger = "heartbeat";
 			gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/orion5x.dtsi b/arch/arm/boot/dts/marvell/orion5x.dtsi
index 61e631b3fd8b..939259c57e05 100644
--- a/arch/arm/boot/dts/orion5x.dtsi
+++ b/arch/arm/boot/dts/marvell/orion5x.dtsi
@@ -1,10 +1,5 @@
-/*
- * Copyright (C) 2012 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2012 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
 
 #define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
 
@@ -151,7 +146,7 @@
 				status = "okay";
 			};
 
-			ehci0: ehci@50000 {
+			ehci0: usb@50000 {
 				compatible = "marvell,orion-ehci";
 				reg = <0x50000 0x1000>;
 				interrupts = <17>;
@@ -223,7 +218,7 @@
 				status = "okay";
 			};
 
-			ehci1: ehci@a0000 {
+			ehci1: usb@a0000 {
 				compatible = "marvell,orion-ehci";
 				reg = <0xa0000 0x1000>;
 				interrupts = <12>;
diff --git a/arch/arm/boot/dts/pxa168-aspenite.dts b/arch/arm/boot/dts/marvell/pxa168-aspenite.dts
index 8bade6bf395b..8bade6bf395b 100644
--- a/arch/arm/boot/dts/pxa168-aspenite.dts
+++ b/arch/arm/boot/dts/marvell/pxa168-aspenite.dts
diff --git a/arch/arm/boot/dts/pxa168.dtsi b/arch/arm/boot/dts/marvell/pxa168.dtsi
index 4fe7735c7c58..22ed10cb5619 100644
--- a/arch/arm/boot/dts/pxa168.dtsi
+++ b/arch/arm/boot/dts/marvell/pxa168.dtsi
@@ -53,6 +53,8 @@
 				compatible = "mrvl,mmp-timer";
 				reg = <0xd4014000 0x100>;
 				interrupts = <13>;
+				clocks = <&soc_clocks PXA168_CLK_TIMER>;
+				resets = <&soc_clocks PXA168_CLK_TIMER>;
 			};
 
 			uart1: serial@d4017000 {
@@ -151,7 +153,7 @@
 			};
 		};
 
-		soc_clocks: clocks{
+		soc_clocks: clocks {
 			compatible = "marvell,pxa168-clock";
 			reg = <0xd4050000 0x1000>,
 			      <0xd4282800 0x400>,
diff --git a/arch/arm/boot/dts/pxa910-dkb.dts b/arch/arm/boot/dts/marvell/pxa910-dkb.dts
index ce76158867c7..ce76158867c7 100644
--- a/arch/arm/boot/dts/pxa910-dkb.dts
+++ b/arch/arm/boot/dts/marvell/pxa910-dkb.dts
diff --git a/arch/arm/boot/dts/pxa910.dtsi b/arch/arm/boot/dts/marvell/pxa910.dtsi
index 352a39357810..bd64ac1ec66f 100644
--- a/arch/arm/boot/dts/pxa910.dtsi
+++ b/arch/arm/boot/dts/marvell/pxa910.dtsi
@@ -163,7 +163,7 @@
 			};
 		};
 
-		soc_clocks: clocks{
+		soc_clocks: clocks {
 			compatible = "marvell,pxa910-clock";
 			reg = <0xd4050000 0x1000>,
 			      <0xd4282800 0x400>,
diff --git a/arch/arm/boot/dts/mediatek/Makefile b/arch/arm/boot/dts/mediatek/Makefile
new file mode 100644
index 000000000000..e48de3efeb3b
--- /dev/null
+++ b/arch/arm/boot/dts/mediatek/Makefile
@@ -0,0 +1,17 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_MEDIATEK) += \
+	mt2701-evb.dtb \
+	mt6572-jty-d101.dtb \
+	mt6572-lenovo-a369i.dtb \
+	mt6580-evbp1.dtb \
+	mt6582-prestigio-pmt5008-3g.dtb \
+	mt6589-aquaris5.dtb \
+	mt6589-fairphone-fp1.dtb \
+	mt6592-evb.dtb \
+	mt7623a-rfb-emmc.dtb \
+	mt7623a-rfb-nand.dtb \
+	mt7623n-rfb-emmc.dtb \
+	mt7623n-bananapi-bpi-r2.dtb \
+	mt7629-rfb.dtb \
+	mt8127-moose.dtb \
+	mt8135-evbp1.dtb
diff --git a/arch/arm/boot/dts/mt2701-evb.dts b/arch/arm/boot/dts/mediatek/mt2701-evb.dts
index d1535f385f36..e97dc37f716c 100644
--- a/arch/arm/boot/dts/mt2701-evb.dts
+++ b/arch/arm/boot/dts/mediatek/mt2701-evb.dts
@@ -50,6 +50,7 @@
 
 	bt_sco_codec:bt_sco_codec {
 		compatible = "linux,bt-sco";
+		#sound-dai-cells = <0>;
 	};
 
 	backlight_lcd: backlight_lcd {
@@ -231,7 +232,7 @@
 				 <MT2701_PIN_238_EXT_SDIO1__FUNC_EXT_SDIO1>,
 				 <MT2701_PIN_237_EXT_SDIO2__FUNC_EXT_SDIO2>,
 				 <MT2701_PIN_236_EXT_SDIO3__FUNC_EXT_SDIO3>;
-			drive-strength = <MTK_DRIVE_4mA>;
+			drive-strength = <4>;
 			bias-pull-up;
 		};
 	};
@@ -244,7 +245,7 @@
 &usb2 {
 	status = "okay";
 	usb-role-switch;
-	connector{
+	connector {
 		compatible = "gpio-usb-b-connector", "usb-b-connector";
 		type = "micro";
 		id-gpios = <&pio 44 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/mt2701-pinfunc.h b/arch/arm/boot/dts/mediatek/mt2701-pinfunc.h
index 136a25a0ae28..136a25a0ae28 100644
--- a/arch/arm/boot/dts/mt2701-pinfunc.h
+++ b/arch/arm/boot/dts/mediatek/mt2701-pinfunc.h
diff --git a/arch/arm/boot/dts/mt2701.dtsi b/arch/arm/boot/dts/mediatek/mt2701.dtsi
index 4776f85d6d5b..ce6a4015fed5 100644
--- a/arch/arm/boot/dts/mt2701.dtsi
+++ b/arch/arm/boot/dts/mediatek/mt2701.dtsi
@@ -178,7 +178,6 @@
 		compatible = "mediatek,mt2701-pinctrl";
 		reg = <0 0x1000b000 0 0x1000>;
 		mediatek,pctl-regmap = <&syscfg_pctl_a>;
-		pins-are-numbered;
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
@@ -360,7 +359,7 @@
 		mediatek,apmixedsys = <&apmixedsys>;
 	};
 
-	nandc: nfi@1100d000 {
+	nandc: nand-controller@1100d000 {
 		compatible = "mediatek,mt2701-nfc";
 		reg = <0 0x1100d000 0 0x1000>;
 		interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_LOW>;
@@ -427,9 +426,9 @@
 
 		afe: audio-controller {
 			compatible = "mediatek,mt2701-audio";
-			interrupts =  <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>,
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>,
 				      <GIC_SPI 132 IRQ_TYPE_LEVEL_LOW>;
-			interrupt-names	= "afe", "asys";
+			interrupt-names = "afe", "asys";
 			power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>;
 
 			clocks = <&infracfg CLK_INFRA_AUDIO>,
@@ -559,12 +558,11 @@
 		compatible = "mediatek,mt2701-jpgdec";
 		reg = <0 0x15004000 0 0x1000>;
 		interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_LOW>;
-		clocks =  <&imgsys CLK_IMG_JPGDEC_SMI>,
+		clocks = <&imgsys CLK_IMG_JPGDEC_SMI>,
 			  <&imgsys CLK_IMG_JPGDEC>;
 		clock-names = "jpgdec-smi",
 			      "jpgdec";
 		power-domains = <&scpsys MT2701_POWER_DOMAIN_ISP>;
-		mediatek,larb = <&larb2>;
 		iommus = <&iommu MT2701_M4U_PORT_JPGDEC_WDMA>,
 			 <&iommu MT2701_M4U_PORT_JPGDEC_BSDMA>;
 	};
@@ -574,10 +572,9 @@
 			     "mediatek,mtk-jpgenc";
 		reg = <0 0x1500a000 0 0x1000>;
 		interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_LOW>;
-		clocks =  <&imgsys CLK_IMG_VENC>;
+		clocks = <&imgsys CLK_IMG_VENC>;
 		clock-names = "jpgenc";
 		power-domains = <&scpsys MT2701_POWER_DOMAIN_ISP>;
-		mediatek,larb = <&larb2>;
 		iommus = <&iommu MT2701_M4U_PORT_JPGENC_RDMA>,
 			 <&iommu MT2701_M4U_PORT_JPGENC_BSDMA>;
 	};
diff --git a/arch/arm/boot/dts/mt6323.dtsi b/arch/arm/boot/dts/mediatek/mt6323.dtsi
index 7fda40ab5fe8..c230c865116d 100644
--- a/arch/arm/boot/dts/mt6323.dtsi
+++ b/arch/arm/boot/dts/mediatek/mt6323.dtsi
@@ -21,10 +21,10 @@
 			status = "disabled";
 		};
 
-		mt6323regulator: mt6323regulator{
+		mt6323regulator: mt6323regulator {
 			compatible = "mediatek,mt6323-regulator";
 
-			mt6323_vproc_reg: buck_vproc{
+			mt6323_vproc_reg: buck_vproc {
 				regulator-name = "vproc";
 				regulator-min-microvolt = < 700000>;
 				regulator-max-microvolt = <1350000>;
@@ -33,7 +33,7 @@
 				regulator-boot-on;
 			};
 
-			mt6323_vsys_reg: buck_vsys{
+			mt6323_vsys_reg: buck_vsys {
 				regulator-name = "vsys";
 				regulator-min-microvolt = <1400000>;
 				regulator-max-microvolt = <2987500>;
@@ -42,13 +42,13 @@
 				regulator-boot-on;
 			};
 
-			mt6323_vpa_reg: buck_vpa{
+			mt6323_vpa_reg: buck_vpa {
 				regulator-name = "vpa";
 				regulator-min-microvolt = < 500000>;
 				regulator-max-microvolt = <3650000>;
 			};
 
-			mt6323_vtcxo_reg: ldo_vtcxo{
+			mt6323_vtcxo_reg: ldo_vtcxo {
 				regulator-name = "vtcxo";
 				regulator-min-microvolt = <2800000>;
 				regulator-max-microvolt = <2800000>;
@@ -57,28 +57,28 @@
 				regulator-boot-on;
 			};
 
-			mt6323_vcn28_reg: ldo_vcn28{
+			mt6323_vcn28_reg: ldo_vcn28 {
 				regulator-name = "vcn28";
 				regulator-min-microvolt = <2800000>;
 				regulator-max-microvolt = <2800000>;
 				regulator-enable-ramp-delay = <185>;
 			};
 
-			mt6323_vcn33_bt_reg: ldo_vcn33_bt{
+			mt6323_vcn33_bt_reg: ldo_vcn33_bt {
 				regulator-name = "vcn33_bt";
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3600000>;
 				regulator-enable-ramp-delay = <185>;
 			};
 
-			mt6323_vcn33_wifi_reg: ldo_vcn33_wifi{
+			mt6323_vcn33_wifi_reg: ldo_vcn33_wifi {
 				regulator-name = "vcn33_wifi";
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3600000>;
 				regulator-enable-ramp-delay = <185>;
 			};
 
-			mt6323_va_reg: ldo_va{
+			mt6323_va_reg: ldo_va {
 				regulator-name = "va";
 				regulator-min-microvolt = <2800000>;
 				regulator-max-microvolt = <2800000>;
@@ -87,14 +87,14 @@
 				regulator-boot-on;
 			};
 
-			mt6323_vcama_reg: ldo_vcama{
+			mt6323_vcama_reg: ldo_vcama {
 				regulator-name = "vcama";
 				regulator-min-microvolt = <1500000>;
 				regulator-max-microvolt = <2800000>;
 				regulator-enable-ramp-delay = <216>;
 			};
 
-			mt6323_vio28_reg: ldo_vio28{
+			mt6323_vio28_reg: ldo_vio28 {
 				regulator-name = "vio28";
 				regulator-min-microvolt = <2800000>;
 				regulator-max-microvolt = <2800000>;
@@ -103,7 +103,7 @@
 				regulator-boot-on;
 			};
 
-			mt6323_vusb_reg: ldo_vusb{
+			mt6323_vusb_reg: ldo_vusb {
 				regulator-name = "vusb";
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
@@ -111,7 +111,7 @@
 				regulator-boot-on;
 			};
 
-			mt6323_vmc_reg: ldo_vmc{
+			mt6323_vmc_reg: ldo_vmc {
 				regulator-name = "vmc";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3300000>;
@@ -119,7 +119,7 @@
 				regulator-boot-on;
 			};
 
-			mt6323_vmch_reg: ldo_vmch{
+			mt6323_vmch_reg: ldo_vmch {
 				regulator-name = "vmch";
 				regulator-min-microvolt = <3000000>;
 				regulator-max-microvolt = <3300000>;
@@ -127,7 +127,7 @@
 				regulator-boot-on;
 			};
 
-			mt6323_vemc3v3_reg: ldo_vemc3v3{
+			mt6323_vemc3v3_reg: ldo_vemc3v3 {
 				regulator-name = "vemc3v3";
 				regulator-min-microvolt = <3000000>;
 				regulator-max-microvolt = <3300000>;
@@ -135,49 +135,49 @@
 				regulator-boot-on;
 			};
 
-			mt6323_vgp1_reg: ldo_vgp1{
+			mt6323_vgp1_reg: ldo_vgp1 {
 				regulator-name = "vgp1";
 				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-enable-ramp-delay = <216>;
 			};
 
-			mt6323_vgp2_reg: ldo_vgp2{
+			mt6323_vgp2_reg: ldo_vgp2 {
 				regulator-name = "vgp2";
 				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <3000000>;
 				regulator-enable-ramp-delay = <216>;
 			};
 
-			mt6323_vgp3_reg: ldo_vgp3{
+			mt6323_vgp3_reg: ldo_vgp3 {
 				regulator-name = "vgp3";
 				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-enable-ramp-delay = <216>;
 			};
 
-			mt6323_vcn18_reg: ldo_vcn18{
+			mt6323_vcn18_reg: ldo_vcn18 {
 				regulator-name = "vcn18";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-enable-ramp-delay = <216>;
 			};
 
-			mt6323_vsim1_reg: ldo_vsim1{
+			mt6323_vsim1_reg: ldo_vsim1 {
 				regulator-name = "vsim1";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3000000>;
 				regulator-enable-ramp-delay = <216>;
 			};
 
-			mt6323_vsim2_reg: ldo_vsim2{
+			mt6323_vsim2_reg: ldo_vsim2 {
 				regulator-name = "vsim2";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3000000>;
 				regulator-enable-ramp-delay = <216>;
 			};
 
-			mt6323_vrtc_reg: ldo_vrtc{
+			mt6323_vrtc_reg: ldo_vrtc {
 				regulator-name = "vrtc";
 				regulator-min-microvolt = <2800000>;
 				regulator-max-microvolt = <2800000>;
@@ -185,28 +185,28 @@
 				regulator-boot-on;
 			};
 
-			mt6323_vcamaf_reg: ldo_vcamaf{
+			mt6323_vcamaf_reg: ldo_vcamaf {
 				regulator-name = "vcamaf";
 				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-enable-ramp-delay = <216>;
 			};
 
-			mt6323_vibr_reg: ldo_vibr{
+			mt6323_vibr_reg: ldo_vibr {
 				regulator-name = "vibr";
 				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-enable-ramp-delay = <36>;
 			};
 
-			mt6323_vrf18_reg: ldo_vrf18{
+			mt6323_vrf18_reg: ldo_vrf18 {
 				regulator-name = "vrf18";
 				regulator-min-microvolt = <1825000>;
 				regulator-max-microvolt = <1825000>;
 				regulator-enable-ramp-delay = <187>;
 			};
 
-			mt6323_vm_reg: ldo_vm{
+			mt6323_vm_reg: ldo_vm {
 				regulator-name = "vm";
 				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <1800000>;
@@ -215,7 +215,7 @@
 				regulator-boot-on;
 			};
 
-			mt6323_vio18_reg: ldo_vio18{
+			mt6323_vio18_reg: ldo_vio18 {
 				regulator-name = "vio18";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
@@ -224,14 +224,14 @@
 				regulator-boot-on;
 			};
 
-			mt6323_vcamd_reg: ldo_vcamd{
+			mt6323_vcamd_reg: ldo_vcamd {
 				regulator-name = "vcamd";
 				regulator-min-microvolt = <1200000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-enable-ramp-delay = <216>;
 			};
 
-			mt6323_vcamio_reg: ldo_vcamio{
+			mt6323_vcamio_reg: ldo_vcamio {
 				regulator-name = "vcamio";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
diff --git a/arch/arm/boot/dts/mediatek/mt6572-jty-d101.dts b/arch/arm/boot/dts/mediatek/mt6572-jty-d101.dts
new file mode 100644
index 000000000000..18c3cab6b7a3
--- /dev/null
+++ b/arch/arm/boot/dts/mediatek/mt6572-jty-d101.dts
@@ -0,0 +1,61 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2025 Max Shevchenko <wctrl@proton.me>
+ */
+
+/dts-v1/;
+#include "mt6572.dtsi"
+
+/ {
+	model = "JTY D101";
+	compatible = "jty,d101", "mediatek,mt6572";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		stdout-path = "serial0:921600n8";
+
+		framebuffer: framebuffer@bf400000 {
+			compatible = "simple-framebuffer";
+			memory-region = <&framebuffer_reserved>;
+			width = <1024>;
+			height = <600>;
+			stride = <(1024 * 2)>;
+			format = "r5g6b5";
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		connsys@80000000 {
+			reg = <0x80000000 0x100000>;
+			no-map;
+		};
+
+		modem@be000000 {
+			reg = <0xbe000000 0x1400000>;
+			no-map;
+		};
+
+		framebuffer_reserved: framebuffer@bf400000 {
+			reg = <0xbf400000 0xc00000>;
+			no-map;
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/mediatek/mt6572-lenovo-a369i.dts b/arch/arm/boot/dts/mediatek/mt6572-lenovo-a369i.dts
new file mode 100644
index 000000000000..c2f0c60ea777
--- /dev/null
+++ b/arch/arm/boot/dts/mediatek/mt6572-lenovo-a369i.dts
@@ -0,0 +1,56 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2025 Max Shevchenko <wctrl@proton.me>
+ */
+
+/dts-v1/;
+#include "mt6572.dtsi"
+
+/ {
+	model = "Lenovo A369i";
+	compatible = "lenovo,a369i", "mediatek,mt6572";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		stdout-path = "serial0:921600n8";
+
+		framebuffer: framebuffer@9fa00000 {
+			compatible = "simple-framebuffer";
+			memory-region = <&framebuffer_reserved>;
+			width = <480>;
+			height = <800>;
+			stride = <(480 * 2)>;
+			format = "r5g6b5";
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		connsys@80000000 {
+			reg = <0x80000000 0x100000>;
+			no-map;
+		};
+
+		framebuffer_reserved: framebuffer@9fa00000 {
+			reg = <0x9fa00000 0x600000>;
+			no-map;
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/mediatek/mt6572.dtsi b/arch/arm/boot/dts/mediatek/mt6572.dtsi
new file mode 100644
index 000000000000..ac70f266d698
--- /dev/null
+++ b/arch/arm/boot/dts/mediatek/mt6572.dtsi
@@ -0,0 +1,108 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2025 Max Shevchenko <wctrl@proton.me>
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&sysirq>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		enable-method = "mediatek,mt6589-smp";
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+		};
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+		};
+	};
+
+	uart_clk: dummy26m {
+		compatible = "fixed-clock";
+		clock-frequency = <26000000>;
+		#clock-cells = <0>;
+	};
+
+	system_clk: dummy13m {
+		compatible = "fixed-clock";
+		clock-frequency = <13000000>;
+		#clock-cells = <0>;
+	};
+
+	rtc_clk: dummy32k {
+		compatible = "fixed-clock";
+		clock-frequency = <32000>;
+		#clock-cells = <0>;
+	};
+
+	soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "simple-bus";
+		ranges;
+
+		watchdog: watchdog@10007000 {
+			compatible = "mediatek,mt6572-wdt", "mediatek,mt6589-wdt";
+			reg = <0x10007000 0x100>;
+			interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_LOW>;
+			timeout-sec = <15>;
+			#reset-cells = <1>;
+		};
+
+		timer: timer@10008000 {
+			compatible = "mediatek,mt6572-timer", "mediatek,mt6577-timer";
+			reg = <0x10008000 0x80>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&system_clk>, <&rtc_clk>;
+			clock-names = "system-clk", "rtc-clk";
+		};
+
+		sysirq: interrupt-controller@10200100 {
+			compatible = "mediatek,mt6572-sysirq", "mediatek,mt6577-sysirq";
+			reg = <0x10200100 0x1c>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			interrupt-parent = <&gic>;
+		};
+
+		gic: interrupt-controller@10211000 {
+			compatible = "arm,cortex-a7-gic";
+			reg = <0x10211000 0x1000>,
+			      <0x10212000 0x2000>,
+			      <0x10214000 0x2000>,
+			      <0x10216000 0x2000>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			interrupt-parent = <&gic>;
+		};
+
+		uart0: serial@11005000 {
+			compatible = "mediatek,mt6572-uart", "mediatek,mt6577-uart";
+			reg = <0x11005000 0x400>;
+			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&uart_clk>;
+			clock-names = "baud";
+			status = "disabled";
+		};
+
+		uart1: serial@11006000 {
+			compatible = "mediatek,mt6572-uart", "mediatek,mt6577-uart";
+			reg = <0x11006000 0x400>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&uart_clk>;
+			clock-names = "baud";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/mt6580-evbp1.dts b/arch/arm/boot/dts/mediatek/mt6580-evbp1.dts
index 755a0774a8ee..755a0774a8ee 100644
--- a/arch/arm/boot/dts/mt6580-evbp1.dts
+++ b/arch/arm/boot/dts/mediatek/mt6580-evbp1.dts
diff --git a/arch/arm/boot/dts/mt6580.dtsi b/arch/arm/boot/dts/mediatek/mt6580.dtsi
index 9e17698c0609..9e17698c0609 100644
--- a/arch/arm/boot/dts/mt6580.dtsi
+++ b/arch/arm/boot/dts/mediatek/mt6580.dtsi
diff --git a/arch/arm/boot/dts/mt6582-prestigio-pmt5008-3g.dts b/arch/arm/boot/dts/mediatek/mt6582-prestigio-pmt5008-3g.dts
index b057e037f940..b057e037f940 100644
--- a/arch/arm/boot/dts/mt6582-prestigio-pmt5008-3g.dts
+++ b/arch/arm/boot/dts/mediatek/mt6582-prestigio-pmt5008-3g.dts
diff --git a/arch/arm/boot/dts/mt6582.dtsi b/arch/arm/boot/dts/mediatek/mt6582.dtsi
index 4263371784cd..4263371784cd 100644
--- a/arch/arm/boot/dts/mt6582.dtsi
+++ b/arch/arm/boot/dts/mediatek/mt6582.dtsi
diff --git a/arch/arm/boot/dts/mt6589-aquaris5.dts b/arch/arm/boot/dts/mediatek/mt6589-aquaris5.dts
index 1e7079a3b449..1e7079a3b449 100644
--- a/arch/arm/boot/dts/mt6589-aquaris5.dts
+++ b/arch/arm/boot/dts/mediatek/mt6589-aquaris5.dts
diff --git a/arch/arm/boot/dts/mt6589-fairphone-fp1.dts b/arch/arm/boot/dts/mediatek/mt6589-fairphone-fp1.dts
index c952347981de..c952347981de 100644
--- a/arch/arm/boot/dts/mt6589-fairphone-fp1.dts
+++ b/arch/arm/boot/dts/mediatek/mt6589-fairphone-fp1.dts
diff --git a/arch/arm/boot/dts/mt6589.dtsi b/arch/arm/boot/dts/mediatek/mt6589.dtsi
index c6babc8ad2ba..c6babc8ad2ba 100644
--- a/arch/arm/boot/dts/mt6589.dtsi
+++ b/arch/arm/boot/dts/mediatek/mt6589.dtsi
diff --git a/arch/arm/boot/dts/mt6592-evb.dts b/arch/arm/boot/dts/mediatek/mt6592-evb.dts
index 5e00c1cca2d1..5e00c1cca2d1 100644
--- a/arch/arm/boot/dts/mt6592-evb.dts
+++ b/arch/arm/boot/dts/mediatek/mt6592-evb.dts
diff --git a/arch/arm/boot/dts/mt6592.dtsi b/arch/arm/boot/dts/mediatek/mt6592.dtsi
index 3716f8db951c..3716f8db951c 100644
--- a/arch/arm/boot/dts/mt6592.dtsi
+++ b/arch/arm/boot/dts/mediatek/mt6592.dtsi
diff --git a/arch/arm/boot/dts/mt7623.dtsi b/arch/arm/boot/dts/mediatek/mt7623.dtsi
index f4848362b3be..fd7a89cc337d 100644
--- a/arch/arm/boot/dts/mt7623.dtsi
+++ b/arch/arm/boot/dts/mediatek/mt7623.dtsi
@@ -241,7 +241,7 @@
 	};
 
 	pericfg: syscon@10003000 {
-		compatible =  "mediatek,mt7623-pericfg",
+		compatible = "mediatek,mt7623-pericfg",
 			      "mediatek,mt2701-pericfg",
 			      "syscon";
 		reg = <0 0x10003000 0 0x1000>;
@@ -253,7 +253,6 @@
 		compatible = "mediatek,mt7623-pinctrl";
 		reg = <0 0x1000b000 0 0x1000>;
 		mediatek,pctl-regmap = <&syscfg_pctl_a>;
-		pins-are-numbered;
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
@@ -309,7 +308,7 @@
 		clock-names = "spi", "wrap";
 	};
 
-	cir: cir@10013000 {
+	cir: ir-receiver@10013000 {
 		compatible = "mediatek,mt7623-cir";
 		reg = <0 0x10013000 0 0x1000>;
 		interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_LOW>;
@@ -628,9 +627,9 @@
 		afe: audio-controller {
 			compatible = "mediatek,mt7623-audio",
 				     "mediatek,mt2701-audio";
-			interrupts =  <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>,
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>,
 				      <GIC_SPI 132 IRQ_TYPE_LEVEL_LOW>;
-			interrupt-names	= "afe", "asys";
+			interrupt-names = "afe", "asys";
 			power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>;
 
 			clocks = <&infracfg CLK_INFRA_AUDIO>,
@@ -981,6 +980,18 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		status = "disabled";
+
+		gmac0: mac@0 {
+			compatible = "mediatek,eth-mac";
+			reg = <0>;
+			status = "disabled";
+		};
+
+		gmac1: mac@1 {
+			compatible = "mediatek,eth-mac";
+			reg = <1>;
+			status = "disabled";
+		};
 	};
 
 	crypto: crypto@1b240000 {
@@ -1132,13 +1143,13 @@
 				 <MT7623_PIN_121_MSDC0_DAT0_FUNC_MSDC0_DAT0>,
 				 <MT7623_PIN_116_MSDC0_CMD_FUNC_MSDC0_CMD>;
 			input-enable;
-			drive-strength = <MTK_DRIVE_2mA>;
+			drive-strength = <2>;
 			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
 		};
 
 		pins-clk {
 			pinmux = <MT7623_PIN_117_MSDC0_CLK_FUNC_MSDC0_CLK>;
-			drive-strength = <MTK_DRIVE_2mA>;
+			drive-strength = <2>;
 			bias-pull-down = <MTK_PUPD_SET_R1R0_01>;
 		};
 
@@ -1156,14 +1167,14 @@
 				 <MT7623_PIN_110_MSDC1_DAT3_FUNC_MSDC1_DAT3>,
 				 <MT7623_PIN_105_MSDC1_CMD_FUNC_MSDC1_CMD>;
 			input-enable;
-			drive-strength = <MTK_DRIVE_4mA>;
+			drive-strength = <4>;
 			bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
 		};
 
 		pins-clk {
 			pinmux = <MT7623_PIN_106_MSDC1_CLK_FUNC_MSDC1_CLK>;
 			bias-pull-down;
-			drive-strength = <MTK_DRIVE_4mA>;
+			drive-strength = <4>;
 		};
 
 		pins-wp {
@@ -1186,13 +1197,13 @@
 				 <MT7623_PIN_110_MSDC1_DAT3_FUNC_MSDC1_DAT3>,
 				 <MT7623_PIN_105_MSDC1_CMD_FUNC_MSDC1_CMD>;
 			input-enable;
-			drive-strength = <MTK_DRIVE_4mA>;
+			drive-strength = <4>;
 			bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
 		};
 
 		pins-clk {
 			pinmux = <MT7623_PIN_106_MSDC1_CLK_FUNC_MSDC1_CLK>;
-			drive-strength = <MTK_DRIVE_4mA>;
+			drive-strength = <4>;
 			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
 		};
 	};
@@ -1200,7 +1211,7 @@
 	nand_pins_default: nanddefault {
 		pins-ale {
 			pinmux = <MT7623_PIN_116_MSDC0_CMD_FUNC_NALE>;
-			drive-strength = <MTK_DRIVE_8mA>;
+			drive-strength = <8>;
 			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
 		};
 
@@ -1215,13 +1226,13 @@
 				 <MT7623_PIN_115_MSDC0_RSTB_FUNC_NLD8>,
 				 <MT7623_PIN_119_MSDC0_DAT2_FUNC_NLD2>;
 			input-enable;
-			drive-strength = <MTK_DRIVE_8mA>;
+			drive-strength = <8>;
 			bias-pull-up;
 		};
 
 		pins-we {
 			pinmux = <MT7623_PIN_117_MSDC0_CLK_FUNC_NWEB>;
-			drive-strength = <MTK_DRIVE_8mA>;
+			drive-strength = <8>;
 			bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
 		};
 	};
diff --git a/arch/arm/boot/dts/mt7623a-rfb-emmc.dts b/arch/arm/boot/dts/mediatek/mt7623a-rfb-emmc.dts
index 13c86936d1c8..5654284bab01 100644
--- a/arch/arm/boot/dts/mt7623a-rfb-emmc.dts
+++ b/arch/arm/boot/dts/mediatek/mt7623a-rfb-emmc.dts
@@ -45,13 +45,13 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&key_pins_a>;
 
-		factory {
+		button-factory {
 			label = "factory";
 			linux,code = <BTN_0>;
 			gpios = <&pio 256 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "wps";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&pio 257 GPIO_ACTIVE_HIGH>;
@@ -112,75 +112,31 @@
 	status = "okay";
 };
 
-&eth {
-	status = "okay";
+&switch0 {
+	ports {
+		port@0 {
+			status = "okay";
+			label = "lan0";
+		};
+
+		port@1 {
+			status = "okay";
+			label = "lan1";
+		};
 
-	gmac0: mac@0 {
-		compatible = "mediatek,eth-mac";
-		reg = <0>;
-		phy-mode = "trgmii";
+		port@2 {
+			status = "okay";
+			label = "lan2";
+		};
 
-		fixed-link {
-			speed = <1000>;
-			full-duplex;
-			pause;
+		port@3 {
+			status = "okay";
+			label = "lan3";
 		};
-	};
 
-	mdio-bus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		switch@0 {
-			compatible = "mediatek,mt7530";
-			reg = <0>;
-			mediatek,mcm;
-			resets = <&ethsys MT2701_ETHSYS_MCM_RST>;
-			reset-names = "mcm";
-			core-supply = <&mt6323_vpa_reg>;
-			io-supply = <&mt6323_vemc3v3_reg>;
-
-			ports {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				port@0 {
-					reg = <0>;
-					label = "lan0";
-				};
-
-				port@1 {
-					reg = <1>;
-					label = "lan1";
-				};
-
-				port@2 {
-					reg = <2>;
-					label = "lan2";
-				};
-
-				port@3 {
-					reg = <3>;
-					label = "lan3";
-				};
-
-				port@4 {
-					reg = <4>;
-					label = "wan";
-				};
-
-				port@6 {
-					reg = <6>;
-					label = "cpu";
-					ethernet = <&gmac0>;
-					phy-mode = "trgmii";
-
-					fixed-link {
-						speed = <1000>;
-						full-duplex;
-					};
-				};
-			};
+		port@4 {
+			status = "okay";
+			label = "wan";
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/mt7623a-rfb-nand.dts b/arch/arm/boot/dts/mediatek/mt7623a-rfb-nand.dts
index 88d8f0b2f4c2..afd177b3b516 100644
--- a/arch/arm/boot/dts/mt7623a-rfb-nand.dts
+++ b/arch/arm/boot/dts/mediatek/mt7623a-rfb-nand.dts
@@ -45,13 +45,13 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&key_pins_a>;
 
-		factory {
+		button-factory {
 			label = "factory";
 			linux,code = <BTN_0>;
 			gpios = <&pio 256 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "wps";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&pio 257 GPIO_ACTIVE_HIGH>;
@@ -116,75 +116,31 @@
 	status = "okay";
 };
 
-&eth {
-	status = "okay";
+&switch0 {
+	ports {
+		port@0 {
+			status = "okay";
+			label = "lan0";
+		};
 
-	gmac0: mac@0 {
-		compatible = "mediatek,eth-mac";
-		reg = <0>;
-		phy-mode = "trgmii";
+		port@1 {
+			status = "okay";
+			label = "lan1";
+		};
 
-		fixed-link {
-			speed = <1000>;
-			full-duplex;
-			pause;
+		port@2 {
+			status = "okay";
+			label = "lan2";
 		};
-	};
 
-	mdio-bus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		switch@0 {
-			compatible = "mediatek,mt7530";
-			reg = <0>;
-			mediatek,mcm;
-			resets = <&ethsys MT2701_ETHSYS_MCM_RST>;
-			reset-names = "mcm";
-			core-supply = <&mt6323_vpa_reg>;
-			io-supply = <&mt6323_vemc3v3_reg>;
-
-			ports {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				port@0 {
-					reg = <0>;
-					label = "lan0";
-				};
-
-				port@1 {
-					reg = <1>;
-					label = "lan1";
-				};
-
-				port@2 {
-					reg = <2>;
-					label = "lan2";
-				};
-
-				port@3 {
-					reg = <3>;
-					label = "lan3";
-				};
-
-				port@4 {
-					reg = <4>;
-					label = "wan";
-				};
-
-				port@6 {
-					reg = <6>;
-					label = "cpu";
-					ethernet = <&gmac0>;
-					phy-mode = "trgmii";
-
-					fixed-link {
-						speed = <1000>;
-						full-duplex;
-					};
-				};
-			};
+		port@3 {
+			status = "okay";
+			label = "lan3";
+		};
+
+		port@4 {
+			status = "okay";
+			label = "wan";
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/mediatek/mt7623a.dtsi b/arch/arm/boot/dts/mediatek/mt7623a.dtsi
new file mode 100644
index 000000000000..bcf909d58a1c
--- /dev/null
+++ b/arch/arm/boot/dts/mediatek/mt7623a.dtsi
@@ -0,0 +1,147 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2017-2018 MediaTek Inc.
+ * Author: Sean Wang <sean.wang@mediatek.com>
+ *
+ */
+
+/dts-v1/;
+#include <dt-bindings/power/mt7623a-power.h>
+#include "mt7623.dtsi"
+
+&afe {
+	power-domains = <&scpsys MT7623A_POWER_DOMAIN_IFR_MSC>;
+};
+
+&crypto {
+	power-domains = <&scpsys MT7623A_POWER_DOMAIN_ETH>;
+};
+
+&gmac0 {
+	status = "okay";
+	phy-mode = "trgmii";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+		pause;
+	};
+};
+
+&gmac1 {
+	status = "okay";
+	phy-mode = "rgmii";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+		pause;
+	};
+};
+
+&eth {
+	status = "okay";
+	power-domains = <&scpsys MT7623A_POWER_DOMAIN_ETH>;
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		switch0: switch@1f {
+			compatible = "mediatek,mt7530";
+			reg = <0x1f>;
+			mediatek,mcm;
+			resets = <&ethsys MT2701_ETHSYS_MCM_RST>;
+			reset-names = "mcm";
+			core-supply = <&mt6323_vpa_reg>;
+			io-supply = <&mt6323_vemc3v3_reg>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					status = "disabled";
+					reg = <0>;
+					label = "swp0";
+				};
+
+				port@1 {
+					status = "disabled";
+					reg = <1>;
+					label = "swp1";
+				};
+
+				port@2 {
+					status = "disabled";
+					reg = <2>;
+					label = "swp2";
+				};
+
+				port@3 {
+					status = "disabled";
+					reg = <3>;
+					label = "swp3";
+				};
+
+				port@4 {
+					status = "disabled";
+					reg = <4>;
+					label = "swp4";
+				};
+
+				port@5 {
+					reg = <5>;
+					label = "cpu";
+					ethernet = <&gmac1>;
+					phy-mode = "rgmii";
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+						pause;
+					};
+				};
+
+				port@6 {
+					reg = <6>;
+					label = "cpu";
+					ethernet = <&gmac0>;
+					phy-mode = "trgmii";
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+						pause;
+					};
+				};
+			};
+		};
+	};
+};
+
+&nandc {
+	power-domains = <&scpsys MT7623A_POWER_DOMAIN_IFR_MSC>;
+};
+
+&pcie {
+	power-domains = <&scpsys MT7623A_POWER_DOMAIN_HIF>;
+};
+
+&scpsys {
+	compatible = "mediatek,mt7623a-scpsys";
+	clocks = <&topckgen CLK_TOP_ETHIF_SEL>;
+	clock-names = "ethif";
+};
+
+&usb0 {
+	power-domains = <&scpsys MT7623A_POWER_DOMAIN_IFR_MSC>;
+};
+
+&usb1 {
+	power-domains = <&scpsys MT7623A_POWER_DOMAIN_HIF>;
+};
+
+&usb2 {
+	power-domains = <&scpsys MT7623A_POWER_DOMAIN_HIF>;
+};
diff --git a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts b/arch/arm/boot/dts/mediatek/mt7623n-bananapi-bpi-r2.dts
index 027c1b0c6a98..a37f3fa223c7 100644
--- a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
+++ b/arch/arm/boot/dts/mediatek/mt7623n-bananapi-bpi-r2.dts
@@ -91,13 +91,13 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&key_pins_a>;
 
-		factory {
+		button-factory {
 			label = "factory";
 			linux,code = <BTN_0>;
 			gpios = <&pio 256 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "wps";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&pio 257 GPIO_ACTIVE_HIGH>;
@@ -171,28 +171,38 @@
 	};
 };
 
-&eth {
+&gmac0 {
 	status = "okay";
+	phy-mode = "trgmii";
 
-	gmac0: mac@0 {
-		compatible = "mediatek,eth-mac";
-		reg = <0>;
-		phy-mode = "trgmii";
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+		pause;
+	};
+};
 
-		fixed-link {
-			speed = <1000>;
-			full-duplex;
-			pause;
-		};
+&gmac1 {
+	status = "okay";
+	phy-mode = "rgmii";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+		pause;
 	};
+};
+
+&eth {
+	status = "okay";
 
-	mdio: mdio-bus {
+	mdio-bus {
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		switch@0 {
+		switch@1f {
 			compatible = "mediatek,mt7530";
-			reg = <0>;
+			reg = <0x1f>;
 			reset-gpios = <&pio 33 0>;
 			core-supply = <&mt6323_vpa_reg>;
 			io-supply = <&mt6323_vemc3v3_reg>;
@@ -226,6 +236,19 @@
 					label = "lan3";
 				};
 
+				port@5 {
+					reg = <5>;
+					label = "cpu";
+					ethernet = <&gmac1>;
+					phy-mode = "rgmii";
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+						pause;
+					};
+				};
+
 				port@6 {
 					reg = <6>;
 					label = "cpu";
@@ -322,6 +345,12 @@
 	vqmmc-supply = <&reg_3p3v>;
 };
 
+&mt6323keys {
+	home {
+		status = "disabled";
+	};
+};
+
 &mt6323_leds {
 	status = "okay";
 
diff --git a/arch/arm/boot/dts/mt7623n-rfb-emmc.dts b/arch/arm/boot/dts/mediatek/mt7623n-rfb-emmc.dts
index 1b9b9a8145a7..34994f3f5a4b 100644
--- a/arch/arm/boot/dts/mt7623n-rfb-emmc.dts
+++ b/arch/arm/boot/dts/mediatek/mt7623n-rfb-emmc.dts
@@ -60,13 +60,13 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&key_pins_a>;
 
-		factory {
+		button-factory {
 			label = "factory";
 			linux,code = <BTN_0>;
 			gpios = <&pio 256 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "wps";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&pio 257 GPIO_ACTIVE_HIGH>;
@@ -156,27 +156,25 @@
 	};
 };
 
-&eth {
+&gmac0 {
 	status = "okay";
+	phy-mode = "trgmii";
 
-	gmac0: mac@0 {
-		compatible = "mediatek,eth-mac";
-		reg = <0>;
-		phy-mode = "trgmii";
-
-		fixed-link {
-			speed = <1000>;
-			full-duplex;
-			pause;
-		};
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+		pause;
 	};
+};
 
-	mac@1 {
-		compatible = "mediatek,eth-mac";
-		reg = <1>;
-		phy-mode = "rgmii";
-		phy-handle = <&phy5>;
-	};
+&gmac1 {
+	status = "okay";
+	phy-mode = "rgmii";
+	phy-handle = <&phy5>;
+};
+
+&eth {
+	status = "okay";
 
 	mdio-bus {
 		#address-cells = <1>;
@@ -187,9 +185,9 @@
 			phy-mode = "rgmii-rxid";
 		};
 
-		switch@0 {
+		switch@1f {
 			compatible = "mediatek,mt7530";
-			reg = <0>;
+			reg = <0x1f>;
 			reset-gpios = <&pio 33 0>;
 			core-supply = <&mt6323_vpa_reg>;
 			io-supply = <&mt6323_vemc3v3_reg>;
@@ -232,6 +230,7 @@
 					fixed-link {
 						speed = <1000>;
 						full-duplex;
+						pause;
 					};
 				};
 			};
diff --git a/arch/arm/boot/dts/mt7623n.dtsi b/arch/arm/boot/dts/mediatek/mt7623n.dtsi
index bcb0846e29fd..3e5cabf19cde 100644
--- a/arch/arm/boot/dts/mt7623n.dtsi
+++ b/arch/arm/boot/dts/mediatek/mt7623n.dtsi
@@ -116,12 +116,11 @@
 			     "mediatek,mt2701-jpgdec";
 		reg = <0 0x15004000 0 0x1000>;
 		interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_LOW>;
-		clocks =  <&imgsys CLK_IMG_JPGDEC_SMI>,
-			  <&imgsys CLK_IMG_JPGDEC>;
+		clocks = <&imgsys CLK_IMG_JPGDEC_SMI>,
+			 <&imgsys CLK_IMG_JPGDEC>;
 		clock-names = "jpgdec-smi",
 			      "jpgdec";
 		power-domains = <&scpsys MT2701_POWER_DOMAIN_ISP>;
-		mediatek,larb = <&larb2>;
 		iommus = <&iommu MT2701_M4U_PORT_JPGDEC_WDMA>,
 			 <&iommu MT2701_M4U_PORT_JPGDEC_BSDMA>;
 	};
@@ -144,7 +143,6 @@
 		interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_LOW>;
 		clocks = <&mmsys CLK_MM_DISP_OVL>;
 		iommus = <&iommu MT2701_M4U_PORT_DISP_OVL_0>;
-		mediatek,larb = <&larb0>;
 	};
 
 	rdma0: rdma@14008000 {
@@ -154,7 +152,6 @@
 		interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_LOW>;
 		clocks = <&mmsys CLK_MM_DISP_RDMA>;
 		iommus = <&iommu MT2701_M4U_PORT_DISP_RDMA>;
-		mediatek,larb = <&larb0>;
 	};
 
 	wdma@14009000 {
@@ -164,7 +161,6 @@
 		interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_LOW>;
 		clocks = <&mmsys CLK_MM_DISP_WDMA>;
 		iommus = <&iommu MT2701_M4U_PORT_DISP_WDMA>;
-		mediatek,larb = <&larb0>;
 	};
 
 	bls: pwm@1400a000 {
@@ -215,7 +211,6 @@
 		interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_LOW>;
 		clocks = <&mmsys CLK_MM_DISP_RDMA1>;
 		iommus = <&iommu MT2701_M4U_PORT_DISP_RDMA1>;
-		mediatek,larb = <&larb0>;
 	};
 
 	dpi0: dpi@14014000 {
diff --git a/arch/arm/boot/dts/mt7629-rfb.dts b/arch/arm/boot/dts/mediatek/mt7629-rfb.dts
index eb536cbebd9b..f24ebc20732a 100644
--- a/arch/arm/boot/dts/mt7629-rfb.dts
+++ b/arch/arm/boot/dts/mediatek/mt7629-rfb.dts
@@ -23,13 +23,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		reset {
+		button-reset {
 			label = "factory";
 			linux,code = <KEY_RESTART>;
 			gpios = <&pio 60 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "wps";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&pio 58 GPIO_ACTIVE_LOW>;
@@ -168,7 +168,7 @@
 	i2c_pins: i2c-pins {
 		mux {
 			function = "i2c";
-			groups =  "i2c_0";
+			groups = "i2c_0";
 		};
 
 		conf {
diff --git a/arch/arm/boot/dts/mt7629.dtsi b/arch/arm/boot/dts/mediatek/mt7629.dtsi
index 46fc236e1b89..acab0883a3bb 100644
--- a/arch/arm/boot/dts/mt7629.dtsi
+++ b/arch/arm/boot/dts/mediatek/mt7629.dtsi
@@ -106,8 +106,7 @@
 			compatible = "mediatek,mt7629-timer",
 				     "mediatek,mt6765-timer";
 			reg = <0x10009000 0x60>;
-			interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clk20m>;
 			clock-names = "clk20m";
 		};
diff --git a/arch/arm/boot/dts/mt8127-moose.dts b/arch/arm/boot/dts/mediatek/mt8127-moose.dts
index 560687af87dc..560687af87dc 100644
--- a/arch/arm/boot/dts/mt8127-moose.dts
+++ b/arch/arm/boot/dts/mediatek/mt8127-moose.dts
diff --git a/arch/arm/boot/dts/mt8127.dtsi b/arch/arm/boot/dts/mediatek/mt8127.dtsi
index aced173c2a52..aced173c2a52 100644
--- a/arch/arm/boot/dts/mt8127.dtsi
+++ b/arch/arm/boot/dts/mediatek/mt8127.dtsi
diff --git a/arch/arm/boot/dts/mt8135-evbp1.dts b/arch/arm/boot/dts/mediatek/mt8135-evbp1.dts
index f6147fe62f41..f6147fe62f41 100644
--- a/arch/arm/boot/dts/mt8135-evbp1.dts
+++ b/arch/arm/boot/dts/mediatek/mt8135-evbp1.dts
diff --git a/arch/arm/boot/dts/mt8135.dtsi b/arch/arm/boot/dts/mediatek/mt8135.dtsi
index a031b3636318..0f291ad22d3a 100644
--- a/arch/arm/boot/dts/mt8135.dtsi
+++ b/arch/arm/boot/dts/mediatek/mt8135.dtsi
@@ -152,7 +152,6 @@
 			compatible = "mediatek,mt8135-pinctrl";
 			reg = <0 0x1000b000 0 0x1000>;
 			mediatek,pctl-regmap = <&syscfg_pctl_a &syscfg_pctl_b>;
-			pins-are-numbered;
 			gpio-controller;
 			#gpio-cells = <2>;
 			interrupt-controller;
diff --git a/arch/arm/boot/dts/meson6-atv1200.dts b/arch/arm/boot/dts/meson6-atv1200.dts
deleted file mode 100644
index 98e1c94c0261..000000000000
--- a/arch/arm/boot/dts/meson6-atv1200.dts
+++ /dev/null
@@ -1,33 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0 OR MIT
-/*
- * Copyright 2014 Carlo Caione <carlo@caione.org>
- */
-
-/dts-v1/;
-#include "meson6.dtsi"
-
-/ {
-	model = "Geniatech ATV1200";
-	compatible = "geniatech,atv1200", "amlogic,meson6";
-
-	aliases {
-		serial0 = &uart_AO;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	memory {
-		device_type = "memory";
-		reg = <0x40000000 0x80000000>;
-	};
-};
-
-&uart_AO {
-	status = "okay";
-};
-
-&ethmac {
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/meson6.dtsi b/arch/arm/boot/dts/meson6.dtsi
deleted file mode 100644
index 4716030a48d0..000000000000
--- a/arch/arm/boot/dts/meson6.dtsi
+++ /dev/null
@@ -1,73 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0 OR MIT
-/*
- * Copyright 2014 Carlo Caione <carlo@caione.org>
- */
-
-#include "meson.dtsi"
-
-/ {
-	model = "Amlogic Meson6 SoC";
-	compatible = "amlogic,meson6";
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu@200 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a9";
-			next-level-cache = <&L2>;
-			reg = <0x200>;
-		};
-
-		cpu@201 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a9";
-			next-level-cache = <&L2>;
-			reg = <0x201>;
-		};
-	};
-
-	apb2: bus@d0000000 {
-		compatible = "simple-bus";
-		reg = <0xd0000000 0x40000>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges = <0x0 0xd0000000 0x40000>;
-	};
-
-	clk81: clk@0 {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <200000000>;
-	};
-}; /* end of / */
-
-&efuse {
-	status = "disabled";
-};
-
-&timer_abcde {
-	clocks = <&xtal>, <&clk81>;
-	clock-names = "xtal", "pclk";
-};
-
-&uart_AO {
-	clocks = <&xtal>, <&clk81>, <&clk81>;
-	clock-names = "xtal", "pclk", "baud";
-};
-
-&uart_A {
-	clocks = <&xtal>, <&clk81>, <&clk81>;
-	clock-names = "xtal", "pclk", "baud";
-};
-
-&uart_B {
-	clocks = <&xtal>, <&clk81>, <&clk81>;
-	clock-names = "xtal", "pclk", "baud";
-};
-
-&uart_C {
-	clocks = <&xtal>, <&clk81>, <&clk81>;
-	clock-names = "xtal", "pclk", "baud";
-};
diff --git a/arch/arm/boot/dts/microchip/Makefile b/arch/arm/boot/dts/microchip/Makefile
new file mode 100644
index 000000000000..79cd38fdc7da
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/Makefile
@@ -0,0 +1,105 @@
+# SPDX-License-Identifier: GPL-2.0
+# Enables support for device-tree overlays
+DTC_FLAGS_at91-sam9x60_curiosity := -@
+DTC_FLAGS_at91-sam9x60ek := -@
+DTC_FLAGS_at91-sam9x75_curiosity := -@
+DTC_FLAGS_at91-sama5d27_som1_ek := -@
+DTC_FLAGS_at91-sama5d27_wlsom1_ek := -@
+DTC_FLAGS_at91-sama5d29_curiosity := -@
+DTC_FLAGS_at91-sama5d2_icp := -@
+DTC_FLAGS_at91-sama5d2_ptc_ek := -@
+DTC_FLAGS_at91-sama5d2_xplained := -@
+DTC_FLAGS_at91-sama5d3_eds := -@
+DTC_FLAGS_at91-sama5d3_xplained := -@
+DTC_FLAGS_at91-sama5d4_xplained := -@
+DTC_FLAGS_at91-sama7d65_curiosity := -@
+DTC_FLAGS_at91-sama7g54_curiosity := -@
+DTC_FLAGS_at91-sama7g5ek := -@
+dtb-$(CONFIG_SOC_AT91RM9200) += \
+	at91rm9200ek.dtb \
+	mpa1600.dtb
+dtb-$(CONFIG_SOC_AT91SAM9) += \
+	animeo_ip.dtb \
+	at91-qil_a9260.dtb \
+	aks-cdu.dtb \
+	ethernut5.dtb \
+	evk-pro3.dtb \
+	tny_a9260.dtb \
+	usb_a9260.dtb \
+	at91sam9260ek.dtb \
+	at91sam9261ek.dtb \
+	at91sam9263ek.dtb \
+	at91-sam9_l9260.dtb \
+	tny_a9263.dtb \
+	usb_a9263.dtb \
+	at91-foxg20.dtb \
+	at91-kizbox.dtb \
+	at91-lmu5000.dtb \
+	at91sam9g20ek.dtb \
+	at91sam9g20ek_2mmc.dtb \
+	tny_a9g20.dtb \
+	usb_a9g20.dtb \
+	usb_a9g20_lpw.dtb \
+	at91sam9m10g45ek.dtb \
+	pm9g45.dtb \
+	at91sam9n12ek.dtb \
+	at91sam9rlek.dtb \
+	at91-ariag25.dtb \
+	at91-ariettag25.dtb \
+	at91-cosino_mega2560.dtb \
+	at91-kizboxmini-base.dtb \
+	at91-kizboxmini-mb.dtb \
+	at91-kizboxmini-rd.dtb \
+	at91-q5xr5.dtb \
+	at91-smartkiz.dtb \
+	at91-wb45n.dtb \
+	at91sam9g15ek.dtb \
+	at91sam9g25-gardena-smart-gateway.dtb \
+	at91sam9g25ek.dtb \
+	at91sam9g35ek.dtb \
+	at91sam9x25ek.dtb \
+	at91sam9x35ek.dtb
+dtb-$(CONFIG_SOC_SAM9X60) += \
+	at91-sam9x60_curiosity.dtb \
+	at91-sam9x60ek.dtb
+dtb-$(CONFIG_SOC_SAM9X7) += \
+	at91-sam9x75_curiosity.dtb
+dtb-$(CONFIG_SOC_SAM_V7) += \
+	at91-kizbox2-2.dtb \
+	at91-kizbox3-hs.dtb \
+	at91-nattis-2-natte-2.dtb \
+	at91-sama5d27_som1_ek.dtb \
+	at91-sama5d27_wlsom1_ek.dtb \
+	at91-sama5d29_curiosity.dtb \
+	at91-sama5d2_icp.dtb \
+	at91-sama5d2_ptc_ek.dtb \
+	at91-sama5d2_xplained.dtb \
+	at91-sama5d3_eds.dtb \
+	at91-sama5d3_ksz9477_evb.dtb \
+	at91-sama5d3_xplained.dtb \
+	at91-dvk_som60.dtb \
+	at91-gatwick.dtb \
+	at91-tse850-3.dtb \
+	at91-wb50n.dtb \
+	sama5d31ek.dtb \
+	sama5d33ek.dtb \
+	sama5d34ek.dtb \
+	sama5d35ek.dtb \
+	sama5d36ek.dtb \
+	sama5d36ek_cmp.dtb \
+	at91-sama5d4_ma5d4evk.dtb \
+	at91-sama5d4_xplained.dtb \
+	at91-sama5d4ek.dtb \
+	at91-vinco.dtb
+dtb-$(CONFIG_SOC_SAMA7D65) += \
+	at91-sama7d65_curiosity.dtb
+dtb-$(CONFIG_SOC_SAMA7G5) += \
+	at91-sama7g54_curiosity.dtb \
+	at91-sama7g5ek.dtb
+
+dtb-$(CONFIG_SOC_LAN966) += \
+	lan966x-kontron-kswitch-d10-mmt-6g-2gs.dtb \
+	lan966x-kontron-kswitch-d10-mmt-8g.dtb \
+	lan966x-pcb8290.dtb \
+	lan966x-pcb8291.dtb \
+	lan966x-pcb8309.dtb
diff --git a/arch/arm/boot/dts/aks-cdu.dts b/arch/arm/boot/dts/microchip/aks-cdu.dts
index 742fcf525e1b..302cb872efa1 100644
--- a/arch/arm/boot/dts/aks-cdu.dts
+++ b/arch/arm/boot/dts/microchip/aks-cdu.dts
@@ -56,7 +56,7 @@
 			};
 		};
 
-		usb0: ohci@500000 {
+		usb0: usb@500000 {
 			num-ports = <2>;
 			status = "okay";
 		};
@@ -98,23 +98,27 @@
 	leds {
 		compatible = "gpio-leds";
 
-		red {
+		led-red {
+			label = "red";
 			gpios = <&pioC 10 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "none";
 		};
 
-		green {
+		led-green {
+			label = "green";
 			gpios = <&pioA 5 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
 			default-state = "on";
 		};
 
-		yellow {
+		led-yellow {
+			label = "yellow";
 			gpios = <&pioB 20 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
 		};
 
-		blue {
+		led-blue {
+			label = "blue";
 			gpios = <&pioB 21 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
 		};
diff --git a/arch/arm/boot/dts/animeo_ip.dts b/arch/arm/boot/dts/microchip/animeo_ip.dts
index 7da718abbd85..c11f4f7dac94 100644
--- a/arch/arm/boot/dts/animeo_ip.dts
+++ b/arch/arm/boot/dts/microchip/animeo_ip.dts
@@ -136,7 +136,7 @@
 			};
 		};
 
-		usb0: ohci@500000 {
+		usb0: usb@500000 {
 			num-ports = <2>;
 			atmel,vbus-gpio = <&pioB 15 GPIO_ACTIVE_LOW>;
 			status = "okay";
@@ -146,48 +146,46 @@
 	leds {
 		compatible = "gpio-leds";
 
-		power_green {
+		led-power-green {
 			label = "power_green";
 			gpios = <&pioC 17 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 
-		power_red {
+		led-power-red {
 			label = "power_red";
 			gpios = <&pioA 2 GPIO_ACTIVE_HIGH>;
 		};
 
-		tx_green {
+		led-tx-green {
 			label = "tx_green";
 			gpios = <&pioC 19 GPIO_ACTIVE_HIGH>;
 		};
 
-		tx_red {
+		led-tx-red {
 			label = "tx_red";
 			gpios = <&pioC 18 GPIO_ACTIVE_HIGH>;
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		keyswitch_in {
+		key-switch-in {
 			label = "keyswitch_in";
 			gpios = <&pioB 1 GPIO_ACTIVE_HIGH>;
 			linux,code = <28>;
 			wakeup-source;
 		};
 
-		error_in {
+		key-error-in {
 			label = "error_in";
 			gpios = <&pioB 2 GPIO_ACTIVE_HIGH>;
 			linux,code = <29>;
 			wakeup-source;
 		};
 
-		btn {
+		key-s {
 			label = "btn";
 			gpios = <&pioC 23 GPIO_ACTIVE_HIGH>;
 			linux,code = <31>;
diff --git a/arch/arm/boot/dts/at91-ariag25.dts b/arch/arm/boot/dts/microchip/at91-ariag25.dts
index 713d18f80356..713d18f80356 100644
--- a/arch/arm/boot/dts/at91-ariag25.dts
+++ b/arch/arm/boot/dts/microchip/at91-ariag25.dts
diff --git a/arch/arm/boot/dts/at91-ariettag25.dts b/arch/arm/boot/dts/microchip/at91-ariettag25.dts
index 2c52a71752c2..2c52a71752c2 100644
--- a/arch/arm/boot/dts/at91-ariettag25.dts
+++ b/arch/arm/boot/dts/microchip/at91-ariettag25.dts
diff --git a/arch/arm/boot/dts/at91-cosino.dtsi b/arch/arm/boot/dts/microchip/at91-cosino.dtsi
index ee0f5da6d819..ee0f5da6d819 100644
--- a/arch/arm/boot/dts/at91-cosino.dtsi
+++ b/arch/arm/boot/dts/microchip/at91-cosino.dtsi
diff --git a/arch/arm/boot/dts/at91-cosino_mega2560.dts b/arch/arm/boot/dts/microchip/at91-cosino_mega2560.dts
index 04cb7bee937d..04cb7bee937d 100644
--- a/arch/arm/boot/dts/at91-cosino_mega2560.dts
+++ b/arch/arm/boot/dts/microchip/at91-cosino_mega2560.dts
diff --git a/arch/arm/boot/dts/at91-dvk_som60.dts b/arch/arm/boot/dts/microchip/at91-dvk_som60.dts
index ededd5b0d27b..ededd5b0d27b 100644
--- a/arch/arm/boot/dts/at91-dvk_som60.dts
+++ b/arch/arm/boot/dts/microchip/at91-dvk_som60.dts
diff --git a/arch/arm/boot/dts/at91-dvk_su60_somc.dtsi b/arch/arm/boot/dts/microchip/at91-dvk_su60_somc.dtsi
index c1c8650dafce..3542ad8a243e 100644
--- a/arch/arm/boot/dts/at91-dvk_su60_somc.dtsi
+++ b/arch/arm/boot/dts/microchip/at91-dvk_su60_somc.dtsi
@@ -44,7 +44,7 @@
 	status = "okay";
 
 	/* spi0.0: 4M Flash Macronix MX25R4035FM1IL0 */
-	spi-flash@0 {
+	flash@0 {
 		compatible = "mxicy,mx25u4035", "jedec,spi-nor";
 		spi-max-frequency = <33000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/at91-dvk_su60_somc_lcm.dtsi b/arch/arm/boot/dts/microchip/at91-dvk_su60_somc_lcm.dtsi
index bea920b192b6..bea920b192b6 100644
--- a/arch/arm/boot/dts/at91-dvk_su60_somc_lcm.dtsi
+++ b/arch/arm/boot/dts/microchip/at91-dvk_su60_somc_lcm.dtsi
diff --git a/arch/arm/boot/dts/at91-foxg20.dts b/arch/arm/boot/dts/microchip/at91-foxg20.dts
index 7edf057047f8..8e9e87665045 100644
--- a/arch/arm/boot/dts/at91-foxg20.dts
+++ b/arch/arm/boot/dts/microchip/at91-foxg20.dts
@@ -131,7 +131,7 @@
 			};
 		};
 
-		usb0: ohci@500000 {
+		usb0: usb@500000 {
 			num-ports = <2>;
 			status = "okay";
 		};
@@ -155,10 +155,10 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		btn {
+		button {
 			label = "Button";
 			gpios = <&pioC 4 GPIO_ACTIVE_LOW>;
 			linux,code = <0x103>;
diff --git a/arch/arm/boot/dts/at91-gatwick.dts b/arch/arm/boot/dts/microchip/at91-gatwick.dts
index 5a81cab5fc3a..551300fd7746 100644
--- a/arch/arm/boot/dts/at91-gatwick.dts
+++ b/arch/arm/boot/dts/microchip/at91-gatwick.dts
@@ -13,7 +13,7 @@
 	model = "Laird Workgroup Bridge 50N - Project Gatwick";
 	compatible = "laird,gatwick", "laird,wb50n", "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 		autorepeat;
 
@@ -31,37 +31,37 @@
 	leds {
 		compatible = "gpio-leds";
 
-		ethernet {
+		led-ethernet {
 			label = "gatwick:yellow:ethernet";
 			gpios = <&pioA 10 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
 
-		wifi {
+		led-wifi {
 			label = "gatwick:green:wifi";
 			gpios = <&pioA 28 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
 
-		ble {
+		led-ble {
 			label = "gatwick:blue:ble";
 			gpios = <&pioA 22 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
 
-		lora {
+		led-lora {
 			label = "gatwick:orange:lora";
 			gpios = <&pioA 26 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
 
-		blank {
+		led-blank {
 			label = "gatwick:green:blank";
 			gpios = <&pioA 24 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
 
-		user {
+		led-user {
 			label = "gatwick:yellow:user";
 			gpios = <&pioA 12 GPIO_ACTIVE_LOW>;
 			default-state = "off";
diff --git a/arch/arm/boot/dts/at91-kizbox.dts b/arch/arm/boot/dts/microchip/at91-kizbox.dts
index 3b8812fcd854..307663b4eec2 100644
--- a/arch/arm/boot/dts/at91-kizbox.dts
+++ b/arch/arm/boot/dts/microchip/at91-kizbox.dts
@@ -28,19 +28,17 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		reset {
+		button-reset {
 			label = "PB_RST";
 			gpios = <&pioB 30 GPIO_ACTIVE_HIGH>;
 			linux,code = <0x100>;
 			wakeup-source;
 		};
 
-		user {
+		button-user {
 			label = "PB_USER";
 			gpios = <&pioB 31 GPIO_ACTIVE_HIGH>;
 			linux,code = <0x101>;
diff --git a/arch/arm/boot/dts/at91-kizbox2-2.dts b/arch/arm/boot/dts/microchip/at91-kizbox2-2.dts
index cab8b3579efa..cab8b3579efa 100644
--- a/arch/arm/boot/dts/at91-kizbox2-2.dts
+++ b/arch/arm/boot/dts/microchip/at91-kizbox2-2.dts
diff --git a/arch/arm/boot/dts/at91-kizbox2-common.dtsi b/arch/arm/boot/dts/microchip/at91-kizbox2-common.dtsi
index c08834ddf07b..a44d92305dbb 100644
--- a/arch/arm/boot/dts/at91-kizbox2-common.dtsi
+++ b/arch/arm/boot/dts/microchip/at91-kizbox2-common.dtsi
@@ -31,26 +31,24 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		prog {
+		button-prog {
 			label = "PB_PROG";
 			gpios = <&pioE 27 GPIO_ACTIVE_LOW>;
 			linux,code = <0x102>;
 			wakeup-source;
 		};
 
-		reset {
+		button-reset {
 			label = "PB_RST";
 			gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
 			linux,code = <0x100>;
 			wakeup-source;
 		};
 
-		user {
+		button-user {
 			label = "PB_USER";
 			gpios = <&pioE 31 GPIO_ACTIVE_HIGH>;
 			linux,code = <0x101>;
@@ -87,7 +85,7 @@
 &i2c1 {
 	status = "okay";
 
-	pmic: act8865@5b {
+	act8865: pmic@5b {
 		compatible = "active-semi,act8865";
 		reg = <0x5b>;
 		status = "okay";
diff --git a/arch/arm/boot/dts/at91-kizbox3-hs.dts b/arch/arm/boot/dts/microchip/at91-kizbox3-hs.dts
index 2799b2a1f4d2..fec7269088d1 100644
--- a/arch/arm/boot/dts/at91-kizbox3-hs.dts
+++ b/arch/arm/boot/dts/microchip/at91-kizbox3-hs.dts
@@ -55,7 +55,7 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default" , "default", "default",
 				"default", "default" ;
@@ -68,35 +68,35 @@
 			     &pinctrl_pio_zbe_rst>;
 		pinctrl-4 = <&pinctrl_pio_input>;
 
-		SW1 {
+		switch-1 {
 			label = "SW1";
 			gpios = <&pioA PIN_PA29 GPIO_ACTIVE_LOW>;
 			linux,code = <0x101>;
 			wakeup-source;
 		};
 
-		SW2 {
+		switch-2 {
 			label = "SW2";
 			gpios = <&pioA PIN_PA18 GPIO_ACTIVE_LOW>;
 			linux,code = <0x102>;
 			wakeup-source;
 		};
 
-		SW3 {
+		switch-3 {
 			label = "SW3";
 			gpios = <&pioA PIN_PA22 GPIO_ACTIVE_LOW>;
 			linux,code = <0x103>;
 			wakeup-source;
 		};
 
-		SW7 {
+		switch-7 {
 			label = "SW7";
 			gpios = <&pioA PIN_PA26 GPIO_ACTIVE_LOW>;
 			linux,code = <0x107>;
 			wakeup-source;
 		};
 
-		SW8 {
+		switch-8 {
 			label = "SW8";
 			gpios = <&pioA PIN_PA24 GPIO_ACTIVE_LOW>;
 			linux,code = <0x108>;
@@ -186,7 +186,7 @@
 
 &pioA {
 	pinctrl_key_gpio_default: key_gpio_default {
-		pinmux=  <PIN_PA22__GPIO>,
+		pinmux = <PIN_PA22__GPIO>,
 		<PIN_PA24__GPIO>,
 		<PIN_PA26__GPIO>,
 		<PIN_PA29__GPIO>,
@@ -225,7 +225,7 @@
 		pinctrl_pio_io_reset: gpio_io_reset {
 			pinmux = <PIN_PB30__GPIO>;
 			bias-disable;
-			drive-open-drain = <1>;
+			drive-open-drain;
 			output-low;
 		};
 		pinctrl_pio_input: gpio_input {
diff --git a/arch/arm/boot/dts/at91-kizbox3_common.dtsi b/arch/arm/boot/dts/microchip/at91-kizbox3_common.dtsi
index abe27adfa4d6..465664628419 100644
--- a/arch/arm/boot/dts/at91-kizbox3_common.dtsi
+++ b/arch/arm/boot/dts/microchip/at91-kizbox3_common.dtsi
@@ -211,7 +211,7 @@
 		pinmux = <PIN_PD12__FLEXCOM4_IO0>, //DATA
 		<PIN_PD13__FLEXCOM4_IO1>; //CLK
 		bias-disable;
-		drive-open-drain = <1>;
+		drive-open-drain;
 	};
 
 	pinctrl_pwm0 {
diff --git a/arch/arm/boot/dts/at91-kizboxmini-base.dts b/arch/arm/boot/dts/microchip/at91-kizboxmini-base.dts
index 81c29ca5cc1b..81c29ca5cc1b 100644
--- a/arch/arm/boot/dts/at91-kizboxmini-base.dts
+++ b/arch/arm/boot/dts/microchip/at91-kizboxmini-base.dts
diff --git a/arch/arm/boot/dts/at91-kizboxmini-common.dtsi b/arch/arm/boot/dts/microchip/at91-kizboxmini-common.dtsi
index 9c622892c692..42640fe6b6d0 100644
--- a/arch/arm/boot/dts/at91-kizboxmini-common.dtsi
+++ b/arch/arm/boot/dts/microchip/at91-kizboxmini-common.dtsi
@@ -36,17 +36,15 @@
 
 	gpio_keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		prog {
+		key-prog {
 			label = "PB_PROG";
 			gpios = <&pioC 17 GPIO_ACTIVE_LOW>;
 			linux,code = <0x102>;
 			wakeup-source;
 		};
 
-		reset {
+		key-reset {
 			label = "PB_RST";
 			gpios = <&pioC 16 GPIO_ACTIVE_LOW>;
 			linux,code = <0x100>;
diff --git a/arch/arm/boot/dts/at91-kizboxmini-mb.dts b/arch/arm/boot/dts/microchip/at91-kizboxmini-mb.dts
index c07d3076a9bc..c07d3076a9bc 100644
--- a/arch/arm/boot/dts/at91-kizboxmini-mb.dts
+++ b/arch/arm/boot/dts/microchip/at91-kizboxmini-mb.dts
diff --git a/arch/arm/boot/dts/at91-kizboxmini-rd.dts b/arch/arm/boot/dts/microchip/at91-kizboxmini-rd.dts
index ab50f4d22387..ab50f4d22387 100644
--- a/arch/arm/boot/dts/at91-kizboxmini-rd.dts
+++ b/arch/arm/boot/dts/microchip/at91-kizboxmini-rd.dts
diff --git a/arch/arm/boot/dts/at91-linea.dtsi b/arch/arm/boot/dts/microchip/at91-linea.dtsi
index 533a440d5583..533a440d5583 100644
--- a/arch/arm/boot/dts/at91-linea.dtsi
+++ b/arch/arm/boot/dts/microchip/at91-linea.dtsi
diff --git a/arch/arm/boot/dts/at91-lmu5000.dts b/arch/arm/boot/dts/microchip/at91-lmu5000.dts
index f8863d7c0798..f8863d7c0798 100644
--- a/arch/arm/boot/dts/at91-lmu5000.dts
+++ b/arch/arm/boot/dts/microchip/at91-lmu5000.dts
diff --git a/arch/arm/boot/dts/at91-natte.dtsi b/arch/arm/boot/dts/microchip/at91-natte.dtsi
index 49f0a0c46cde..49f0a0c46cde 100644
--- a/arch/arm/boot/dts/at91-natte.dtsi
+++ b/arch/arm/boot/dts/microchip/at91-natte.dtsi
diff --git a/arch/arm/boot/dts/at91-nattis-2-natte-2.dts b/arch/arm/boot/dts/microchip/at91-nattis-2-natte-2.dts
index 4f123477e631..f71377c9b757 100644
--- a/arch/arm/boot/dts/at91-nattis-2-natte-2.dts
+++ b/arch/arm/boot/dts/microchip/at91-nattis-2-natte-2.dts
@@ -18,7 +18,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "Wakeup";
 			linux,code = <10>;
 			wakeup-source;
diff --git a/arch/arm/boot/dts/at91-q5xr5.dts b/arch/arm/boot/dts/microchip/at91-q5xr5.dts
index 47a00062f01f..9cf60b6f695c 100644
--- a/arch/arm/boot/dts/at91-q5xr5.dts
+++ b/arch/arm/boot/dts/microchip/at91-q5xr5.dts
@@ -125,7 +125,7 @@
 	cs-gpios = <&pioA 3 GPIO_ACTIVE_HIGH>, <&pioC 11 GPIO_ACTIVE_LOW>, <0>, <0>;
 	status = "okay";
 
-	m25p80@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/at91-qil_a9260.dts b/arch/arm/boot/dts/microchip/at91-qil_a9260.dts
index 969d990767fc..892dbd8dbbed 100644
--- a/arch/arm/boot/dts/at91-qil_a9260.dts
+++ b/arch/arm/boot/dts/microchip/at91-qil_a9260.dts
@@ -108,13 +108,13 @@
 				status = "okay";
 			};
 
-			shdwc@fffffd10 {
+			shdwc: poweroff@fffffd10 {
 				atmel,wakeup-counter = <10>;
 				atmel,wakeup-rtt-timer;
 			};
 		};
 
-		usb0: ohci@500000 {
+		usb0: usb@500000 {
 			num-ports = <2>;
 			status = "okay";
 		};
@@ -198,10 +198,8 @@
 
 	gpio_keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		user_pb {
+		button-user {
 			label = "user_pb";
 			gpios = <&pioB 10 GPIO_ACTIVE_LOW>;
 			linux,code = <28>;
diff --git a/arch/arm/boot/dts/at91-sam9_l9260.dts b/arch/arm/boot/dts/microchip/at91-sam9_l9260.dts
index 1e2a28c2f365..49dc1a4ccb36 100644
--- a/arch/arm/boot/dts/at91-sam9_l9260.dts
+++ b/arch/arm/boot/dts/microchip/at91-sam9_l9260.dts
@@ -101,11 +101,11 @@
 		nand0: nand@40000000 {
 			nand-bus-width = <8>;
 			nand-ecc-mode = "soft";
-			nand-on-flash-bbt = <1>;
+			nand-on-flash-bbt;
 			status = "okay";
 		};
 
-		usb0: ohci@500000 {
+		usb0: usb@500000 {
 			status = "okay";
 		};
 
diff --git a/arch/arm/boot/dts/microchip/at91-sam9x60_curiosity.dts b/arch/arm/boot/dts/microchip/at91-sam9x60_curiosity.dts
new file mode 100644
index 000000000000..b9ffd9e5faac
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/at91-sam9x60_curiosity.dts
@@ -0,0 +1,508 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * at91-sam9x60_curiosity.dts - Device Tree file for Microchip SAM9X60 Curiosity board
+ *
+ * Copyright (C) 2022 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Durai Manickam KR <durai.manickamkr@microchip.com>
+ */
+/dts-v1/;
+#include "sam9x60.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Microchip SAM9X60 Curiosity";
+	compatible = "microchip,sam9x60-curiosity", "microchip,sam9x60", "atmel,at91sam9";
+
+	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c6;
+		serial2 = &uart7;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@20000000 {
+		reg = <0x20000000 0x8000000>;
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <24000000>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_key_gpio_default>;
+
+		button-user {
+			label = "PB_USER";
+			gpios = <&pioA 29 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_PROG1>;
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+
+		led-red {
+			label = "red";
+			gpios = <&pioD 17 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-green {
+			label = "green";
+			gpios = <&pioD 19 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-blue {
+			label = "blue";
+			gpios = <&pioD 21 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+
+	vdd_1v8: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <1800000>;
+		regulator-min-microvolt = <1800000>;
+		regulator-name = "VDD_1V8";
+	};
+
+	vdd_1v15: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <1150000>;
+		regulator-min-microvolt = <1150000>;
+		regulator-name = "VDD_1V15";
+	};
+
+	vdd1_3v3: regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "VDD1_3V3";
+	};
+};
+
+&adc {
+	vddana-supply = <&vdd1_3v3>;
+	vref-supply = <&vdd1_3v3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc_default &pinctrl_adtrg_default>;
+	status = "okay";
+};
+
+&can0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can0_rx_tx>;
+	status = "disabled"; /* Conflict with dbgu. */
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1_rx_tx>;
+	status = "okay";
+};
+
+&dbgu {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_dbgu>;
+	status = "okay"; /* Conflict with can0. */
+};
+
+&ebi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ebi_addr_nand &pinctrl_ebi_data_lsb>;
+	status = "okay";
+
+	nand_controller: nand-controller {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_nand_oe_we &pinctrl_nand_cs &pinctrl_nand_rb>;
+		status = "okay";
+
+		nand@3 {
+			reg = <0x3 0x0 0x800000>;
+			rb-gpios = <&pioD 5 GPIO_ACTIVE_HIGH>;
+			cs-gpios = <&pioD 4 GPIO_ACTIVE_HIGH>;
+			nand-bus-width = <8>;
+			nand-ecc-mode = "hw";
+			nand-ecc-strength = <8>;
+			nand-ecc-step-size = <512>;
+			nand-on-flash-bbt;
+			label = "atmel_nand";
+
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				at91bootstrap@0 {
+					label = "at91bootstrap";
+					reg = <0x0 0x40000>;
+				};
+
+				uboot@40000 {
+					label = "u-boot";
+					reg = <0x40000 0xc0000>;
+				};
+
+				ubootenvred@100000 {
+					label = "U-Boot Env Redundant";
+					reg = <0x100000 0x40000>;
+				};
+
+				ubootenv@140000 {
+					label = "U-Boot Env";
+					reg = <0x140000 0x40000>;
+				};
+
+				dtb@180000 {
+					label = "device tree";
+					reg = <0x180000 0x80000>;
+				};
+
+				kernel@200000 {
+					label = "kernel";
+					reg = <0x200000 0x600000>;
+				};
+
+				rootfs@800000 {
+					label = "rootfs";
+					reg = <0x800000 0x1f800000>;
+				};
+			};
+		};
+	};
+};
+
+&flx0 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+
+	i2c0: i2c@600 {
+		dmas = <0>, <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_flx0_default>;
+		i2c-analog-filter;
+		i2c-digital-filter;
+		i2c-digital-filter-width-ns = <35>;
+		status = "okay";
+
+		eeprom@53 {
+			compatible = "atmel,24c02";
+			reg = <0x53>;
+			pagesize = <16>;
+		};
+	};
+};
+
+&flx6 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+
+	i2c6: i2c@600 {
+		dmas = <0>, <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_flx6_default>;
+		i2c-analog-filter;
+		i2c-digital-filter;
+		i2c-digital-filter-width-ns = <35>;
+		status = "disabled";
+	};
+};
+
+&flx7 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+	status = "okay";
+
+	uart7: serial@200 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_flx7_default>;
+		status = "okay";
+	};
+};
+
+&macb0 {
+	phy-mode = "rmii";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_macb0_rmii>;
+	status = "okay";
+
+	ethernet-phy@0 {
+		reg = <0x0>;
+		interrupt-parent = <&pioB>;
+		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&pinctrl {
+	adc {
+		pinctrl_adc_default: adc-default {
+			atmel,pins = <AT91_PIOB 14 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_adtrg_default: adtrg-default {
+			atmel,pins = <AT91_PIOB 18 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>;
+		};
+	};
+
+	can0 {
+		pinctrl_can0_rx_tx: can0-rx-tx {
+			atmel,pins =
+				<AT91_PIOA 9 AT91_PERIPH_B AT91_PINCTRL_NONE	/* CANRX0 */
+				 AT91_PIOA 10 AT91_PERIPH_B AT91_PINCTRL_NONE	/* CANTX0 */
+				 AT91_PIOC 9 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_DOWN>;	/* Enable CAN Transceivers */
+		};
+	};
+
+	can1 {
+		pinctrl_can1_rx_tx: can1-rx-tx {
+			atmel,pins =
+				<AT91_PIOA 6 AT91_PERIPH_B AT91_PINCTRL_NONE	/* CANRX1 */
+				 AT91_PIOA 5 AT91_PERIPH_B AT91_PINCTRL_NONE	/* CANTX1 */
+				 AT91_PIOB 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_DOWN>;	/* Enable CAN Transceivers */
+		};
+	};
+
+	dbgu {
+		pinctrl_dbgu: dbgu-0 {
+			atmel,pins = <AT91_PIOA 9 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+				      AT91_PIOA 10 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+		};
+	};
+
+	ebi {
+		pinctrl_ebi_data_lsb: ebi-data-lsb {
+			atmel,pins =
+				<AT91_PIOD 6 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 7 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 8 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 9 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 10 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 11 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 12 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 13 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)>;
+		};
+
+		pinctrl_ebi_addr_nand: ebi-addr-nand {
+			atmel,pins =
+				<AT91_PIOD 2 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 3 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)>;
+		};
+	};
+
+	flexcom {
+		pinctrl_flx0_default: flx0-twi {
+			atmel,pins =
+				<AT91_PIOA 0 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+				 AT91_PIOA 1 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
+		};
+
+		pinctrl_flx6_default: flx6-twi {
+			atmel,pins =
+				<AT91_PIOA 30 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+				 AT91_PIOA 31 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
+		};
+
+		pinctrl_flx7_default: flx7-usart {
+			atmel,pins =
+				<AT91_PIOC 0 AT91_PERIPH_C AT91_PINCTRL_NONE
+				 AT91_PIOC 1 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+		};
+	};
+
+	gpio-keys {
+		pinctrl_key_gpio_default: pinctrl-key-gpio {
+			atmel,pins = <AT91_PIOA 29 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+	};
+
+	leds {
+		pinctrl_gpio_leds: gpio-leds {
+			atmel,pins = <AT91_PIOD 17 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+				      AT91_PIOD 19 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+				      AT91_PIOD 21 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+	};
+
+	macb0 {
+		pinctrl_macb0_rmii: macb0-rmii-0 {
+			atmel,pins =
+				<AT91_PIOB 0 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB0 periph A */
+				 AT91_PIOB 1 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB1 periph A */
+				 AT91_PIOB 2 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB2 periph A */
+				 AT91_PIOB 3 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB3 periph A */
+				 AT91_PIOB 4 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB4 periph A */
+				 AT91_PIOB 5 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB5 periph A */
+				 AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB6 periph A */
+				 AT91_PIOB 7 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB7 periph A */
+				 AT91_PIOB 8 AT91_PERIPH_GPIO AT91_PINCTRL_NONE	/* PB8 IRQ GPIO */
+				 AT91_PIOB 9 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB9 periph A */
+				 AT91_PIOB 10 AT91_PERIPH_A AT91_PINCTRL_NONE>;	/* PB10 periph A */
+		};
+	};
+
+	nand {
+		pinctrl_nand_oe_we: nand-oe-we-0 {
+			atmel,pins =
+				<AT91_PIOD 0 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 1 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)>;
+		};
+
+		pinctrl_nand_rb: nand-rb-0 {
+			atmel,pins =
+				<AT91_PIOD 5 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
+		};
+
+		pinctrl_nand_cs: nand-cs-0 {
+			atmel,pins =
+				<AT91_PIOD 4 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
+		};
+	};
+
+	pwm0 {
+		pinctrl_pwm0_0: pwm0-0 {
+			atmel,pins = <AT91_PIOB 12 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_pwm0_1: pwm0-1 {
+			atmel,pins = <AT91_PIOB 13 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_pwm0_2: pwm0-2 {
+			atmel,pins = <AT91_PIOD 16 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+		};
+	};
+
+	sdmmc0 {
+		pinctrl_sdmmc0_default: sdmmc0 {
+			atmel,pins =
+				<AT91_PIOA 17 AT91_PERIPH_A (AT91_PINCTRL_DRIVE_STRENGTH_HI)				/* PA17 CK  periph A with pullup */
+				 AT91_PIOA 16 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)	/* PA16 CMD periph A with pullup */
+				 AT91_PIOA 15 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)	/* PA15 DAT0 periph A */
+				 AT91_PIOA 18 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)	/* PA18 DAT1 periph A with pullup */
+				 AT91_PIOA 19 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)	/* PA19 DAT2 periph A with pullup */
+				 AT91_PIOA 20 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)>;	/* PA20 DAT3 periph A with pullup */
+		};
+
+		pinctrl_sdmmc0_cd: sdmmc0-cd {
+			atmel,pins =
+				<AT91_PIOA 25 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+	};
+
+	sdmmc1 {
+		pinctrl_sdmmc1_default: sdmmc1 {
+			atmel,pins =
+				<AT91_PIOA 13 AT91_PERIPH_B (AT91_PINCTRL_DRIVE_STRENGTH_HI)				/* PA13 CK periph B */
+				 AT91_PIOA 12 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)	/* PA12 CMD periph B with pullup */
+				 AT91_PIOA 11 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)	/* PA11 DAT0 periph B with pullup */
+				 AT91_PIOA 2 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)	/* PA2 DAT1 periph B with pullup */
+				 AT91_PIOA 3 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)	/* PA3 DAT2 periph B with pullup */
+				 AT91_PIOA 4 AT91_PERIPH_B (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI)>;	/* PA4 DAT3 periph B with pullup */
+		};
+	};
+
+	usb0 {
+		pinctrl_usba_vbus: usba-vbus {
+			atmel,pins = <AT91_PIOA 27 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+	};
+
+	usb1 {
+		pinctrl_usb_default: usb-default {
+			atmel,pins = <AT91_PIOD 18 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+				      AT91_PIOD 15 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+	};
+}; /* pinctrl */
+
+&pwm0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_0 &pinctrl_pwm0_1 &pinctrl_pwm0_2>;
+	status = "okay";
+};
+
+&rtt {
+	atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
+};
+
+&sdmmc0 {
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdmmc0_default &pinctrl_sdmmc0_cd>;
+	cd-gpios = <&pioA 25 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	status = "okay";
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdmmc1_default>;
+	disable-wp;
+	status = "okay";
+};
+
+&shutdown_controller {
+	debounce-delay-us = <976>;
+	status = "okay";
+
+	input@0 {
+		reg = <0>;
+	};
+};
+
+&tcb0 {
+	timer0: timer@0 {
+		compatible = "atmel,tcb-timer";
+		reg = <0>;
+	};
+
+	timer1: timer@1 {
+		compatible = "atmel,tcb-timer";
+		reg = <1>;
+	};
+};
+
+&usb0 {
+	atmel,vbus-gpio = <&pioA 27 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usba_vbus>;
+	status = "okay";
+};
+
+&usb1 {
+	num-ports = <3>;
+	atmel,vbus-gpio = <0
+			   &pioD 18 GPIO_ACTIVE_HIGH
+			   &pioD 15 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_default>;
+	status = "okay";
+};
+
+&usb2 {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/at91-sam9x60ek.dts b/arch/arm/boot/dts/microchip/at91-sam9x60ek.dts
index 7719ea3d4933..c1ff3248bd8f 100644
--- a/arch/arm/boot/dts/at91-sam9x60ek.dts
+++ b/arch/arm/boot/dts/microchip/at91-sam9x60ek.dts
@@ -16,8 +16,8 @@
 
 	aliases {
 		i2c0 = &i2c0;
-		i2c1 = &i2c1;
-		serial1 = &uart1;
+		i2c1 = &i2c6;
+		serial1 = &uart5;
 	};
 
 	chosen {
@@ -34,58 +34,15 @@
 		};
 	};
 
-	regulators: regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		vdd_1v8: fixed-regulator-vdd_1v8@0 {
-			compatible = "regulator-fixed";
-			regulator-name = "VDD_1V8";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-always-on;
-			status = "okay";
-		};
-
-		vdd_1v15: fixed-regulator-vdd_1v15@1 {
-			compatible = "regulator-fixed";
-			regulator-name = "VDD_1V15";
-			regulator-min-microvolt = <1150000>;
-			regulator-max-microvolt = <1150000>;
-			regulator-always-on;
-			status = "okay";
-		};
-
-		vdd1_3v3: fixed-regulator-vdd1_3v3@2 {
-			compatible = "regulator-fixed";
-			regulator-name = "VDD1_3V3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-			status = "okay";
-		};
-
-		vdd2_3v3: regulator-fixed-vdd2_3v3@3 {
-			compatible = "regulator-fixed";
-			regulator-name = "VDD2_3V3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-			status = "okay";
-		};
-	};
-
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_key_gpio_default>;
-		status = "okay";
 
-		sw1 {
+		button-1 {
 			label = "SW1";
 			gpios = <&pioD 18 GPIO_ACTIVE_LOW>;
-			linux,code=<KEY_PROG1>;
+			linux,code = <KEY_PROG1>;
 			wakeup-source;
 		};
 	};
@@ -96,22 +53,54 @@
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 		status = "okay"; /* Conflict with pwm0. */
 
-		red {
+		led-red {
 			label = "red";
 			gpios = <&pioB 11 GPIO_ACTIVE_HIGH>;
 		};
 
-		green {
+		led-green {
 			label = "green";
 			gpios = <&pioB 12 GPIO_ACTIVE_HIGH>;
 		};
 
-		blue {
+		led-blue {
 			label = "blue";
 			gpios = <&pioB 13 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 	};
+
+	vdd_1v8: fixed-regulator-vdd_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	vdd_1v15: fixed-regulator-vdd_1v15 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_1V15";
+		regulator-min-microvolt = <1150000>;
+		regulator-max-microvolt = <1150000>;
+		regulator-always-on;
+	};
+
+	vdd1_3v3: fixed-regulator-vdd1_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD1_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	vdd2_3v3: regulator-fixed-vdd2_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD2_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 };
 
 &adc {
@@ -218,25 +207,18 @@
 	status = "okay";
 
 	i2c0: i2c@600 {
-		compatible = "microchip,sam9x60-i2c";
-		reg = <0x600 0x200>;
-		interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+		dmas = <0>, <0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_flx0_default>;
-		atmel,fifo-size = <16>;
 		i2c-analog-filter;
 		i2c-digital-filter;
 		i2c-digital-filter-width-ns = <35>;
 		status = "okay";
 
 		eeprom@53 {
-			compatible = "atmel,24c32";
+			compatible = "atmel,24c02";
 			reg = <0x53>;
 			pagesize = <16>;
-			size = <128>;
 			status = "okay";
 		};
 	};
@@ -246,17 +228,10 @@
 	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
 	status = "disabled";
 
-	spi0: spi@400 {
-		compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
-		reg = <0x400 0x200>;
-		interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
-		clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
-		clock-names = "spi_clk";
+	spi4: spi@400 {
+		dmas = <0>, <0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_flx4_default>;
-		atmel,fifo-size = <16>;
-		#address-cells = <1>;
-		#size-cells = <0>;
 		status = "disabled";
 	};
 };
@@ -265,23 +240,9 @@
 	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
 	status = "okay";
 
-	uart1: serial@200 {
-		compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
-		reg = <0x200 0x200>;
-		interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
-		dmas = <&dma0
-			(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
-			 AT91_XDMAC_DT_PERID(10))>,
-		       <&dma0
-			(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
-			 AT91_XDMAC_DT_PERID(11))>;
-		dma-names = "tx", "rx";
-		clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
-		clock-names = "usart";
-		pinctrl-0 = <&pinctrl_flx5_default>;
+	uart5: serial@200 {
 		pinctrl-names = "default";
-		atmel,use-dma-rx;
-		atmel,use-dma-tx;
+		pinctrl-0 = <&pinctrl_flx5_default>;
 		status = "okay";
 	};
 };
@@ -290,21 +251,46 @@
 	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
 	status = "okay";
 
-	i2c1: i2c@600 {
-		compatible = "microchip,sam9x60-i2c";
-		reg = <0x600 0x200>;
-		interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+	i2c6: i2c@600 {
+		dmas = <0>, <0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_flx6_default>;
-		atmel,fifo-size = <16>;
 		i2c-analog-filter;
 		i2c-digital-filter;
 		i2c-digital-filter-width-ns = <35>;
 		status = "okay";
 
+		power-monitor@17 {
+			compatible = "microchip,pac1934";
+			reg = <0x17>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@1 {
+				reg = <0x1>;
+				shunt-resistor-micro-ohms = <10000>;
+				label = "VDDIOM";
+			};
+
+			channel@2 {
+				reg = <0x2>;
+				shunt-resistor-micro-ohms = <10000>;
+				label = "VDDCORE";
+			};
+
+			channel@3 {
+				reg = <0x3>;
+				shunt-resistor-micro-ohms = <10000>;
+				label = "VDD3V3_MPU";
+			};
+
+			channel@4 {
+				reg = <0x4>;
+				shunt-resistor-micro-ohms = <10000>;
+				label = "VDD3V3";
+			};
+		};
+
 		gpio_exp: mcp23008@20 {
 			compatible = "microchip,mcp23008";
 			reg = <0x20>;
@@ -333,6 +319,8 @@
 
 	ethernet-phy@0 {
 		reg = <0x0>;
+		interrupt-parent = <&pioB>;
+		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
 	};
 };
 
@@ -450,7 +438,7 @@
 				 AT91_PIOA 14 AT91_PERIPH_A AT91_PINCTRL_NONE>;
 		};
 
-		pinctrl_flx5_default: flx_uart {
+		pinctrl_flx5_default: flx5_uart {
 			atmel,pins =
 				<AT91_PIOA 7 AT91_PERIPH_C AT91_PINCTRL_NONE
 				 AT91_PIOA 8 AT91_PERIPH_B AT91_PINCTRL_NONE
@@ -506,6 +494,7 @@
 				 AT91_PIOB 5 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB5 periph A */
 				 AT91_PIOB 6 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB6 periph A */
 				 AT91_PIOB 7 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB7 periph A */
+				 AT91_PIOB 8 AT91_PERIPH_GPIO AT91_PINCTRL_NONE	/* PB8 IRQ GPIO */
 				 AT91_PIOB 9 AT91_PERIPH_A AT91_PINCTRL_NONE	/* PB9 periph A */
 				 AT91_PIOB 10 AT91_PERIPH_A AT91_PINCTRL_NONE>;	/* PB10 periph A */
 		};
@@ -619,7 +608,8 @@
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
 		reg = <0>;
-		spi-max-frequency = <80000000>;
+		spi-max-frequency = <104000000>;
+		spi-cs-setup-delay-ns = <7>;
 		spi-tx-bus-width = <4>;
 		spi-rx-bus-width = <4>;
 		m25p,fast-read;
diff --git a/arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dts b/arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dts
new file mode 100644
index 000000000000..1a6a909a5043
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/at91-sam9x75_curiosity.dts
@@ -0,0 +1,374 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * at91-sam9x75_curiosity.dts - Device Tree file for Microchip SAM9X75 Curiosity board
+ *
+ * Copyright (C) 2023 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Varshini Rajendran <varshini.rajendran@microchip.com>
+ */
+/dts-v1/;
+#include "sam9x7.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Microchip SAM9X75 Curiosity";
+	compatible = "microchip,sam9x75-curiosity", "microchip,sam9x7", "atmel,at91sam9";
+
+	aliases {
+		i2c0 = &i2c6;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_key_gpio_default>;
+
+		button-user {
+			label = "USER";
+			gpios = <&pioC 9 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_0>;
+			wakeup-source;
+		};
+	};
+
+	led-controller {
+		compatible = "gpio-leds";
+
+		led_red: led-red {
+			label = "red";
+			gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
+			pinctrl-0 = <&pinctrl_red_led_gpio_default>;
+		};
+
+		led_green: led-green {
+			label = "green";
+			gpios = <&pioC 21 GPIO_ACTIVE_HIGH>;
+			pinctrl-0 = <&pinctrl_green_led_gpio_default>;
+		};
+
+		led_blue: led-blue {
+			label = "blue";
+			gpios = <&pioC 20 GPIO_ACTIVE_HIGH>;
+			pinctrl-0 = <&pinctrl_blue_led_gpio_default>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	memory@20000000 {
+		reg = <0x20000000 0x10000000>;
+		device_type = "memory";
+	};
+};
+
+&classd {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_classd_default>;
+	atmel,pwm-type = "diff";
+	atmel,non-overlap-time = <10>;
+	status = "okay";
+};
+
+&dbgu {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_dbgu_default>;
+	status = "okay";
+};
+
+&dma0 {
+	status = "okay";
+};
+
+&flx6 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+};
+
+&i2c6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flx6_default>;
+	i2c-analog-filter;
+	i2c-digital-filter;
+	i2c-digital-filter-width-ns = <35>;
+	status = "okay";
+
+	pmic@5b {
+		compatible = "microchip,mcp16502";
+		reg = <0x5b>;
+
+		regulators {
+			vdd_3v3: VDD_IO {
+				regulator-name = "VDD_IO";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-mode = <4>;
+				};
+			};
+
+			vddioddr: VDD_DDR {
+				regulator-name = "VDD_DDR";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-mode = <4>;
+				};
+			};
+
+			vddcore: VDD_CORE {
+				regulator-name = "VDD_CORE";
+				regulator-min-microvolt = <1150000>;
+				regulator-max-microvolt = <1150000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-mode = <4>;
+				};
+			};
+
+			dcdc4: VDD_OTHER {
+				regulator-name = "VDD_OTHER";
+				regulator-min-microvolt = <1150000>;
+				regulator-max-microvolt = <1150000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-ramp-delay = <3125>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-mode = <4>;
+				};
+			};
+
+			vldo1: LDO1 {
+				regulator-name = "LDO1";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vldo2: LDO2 {
+				regulator-name = "LDO2";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&flx7 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+};
+
+&i2c7 {
+	dmas = <0>, <0>;
+	i2c-analog-filter;
+	i2c-digital-filter;
+	i2c-digital-filter-width-ns = <35>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flx7_default>;
+	status = "okay";
+
+	power-monitor@10 {
+		compatible = "microchip,pac1934";
+		reg = <0x10>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@1 {
+			reg = <0x1>;
+			shunt-resistor-micro-ohms = <10000>;
+			label = "VDD3V3";
+		};
+
+		channel@2 {
+			reg = <0x2>;
+			shunt-resistor-micro-ohms = <10000>;
+			label = "DCDC4";
+		};
+
+		channel@3 {
+			reg = <0x3>;
+			shunt-resistor-micro-ohms = <10000>;
+			label = "VDDCORE";
+		};
+
+		channel@4 {
+			reg = <0x4>;
+			shunt-resistor-micro-ohms = <10000>;
+			label = "VDDIODDR";
+		};
+	};
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2s_default>;
+	#sound-dai-cells = <0>;
+	status = "okay";
+};
+
+&main_xtal {
+	clock-frequency = <24000000>;
+};
+
+&pinctrl {
+	classd {
+		pinctrl_classd_default: classd-default {
+			atmel,pins =
+				<AT91_PIOA 18 AT91_PERIPH_C AT91_PINCTRL_PULL_UP>,
+				<AT91_PIOA 19 AT91_PERIPH_C AT91_PINCTRL_PULL_DOWN>;
+		};
+	};
+
+	dbgu {
+		pinctrl_dbgu_default: dbgu-default {
+			atmel,pins = <AT91_PIOA 26 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
+				     <AT91_PIOA 27 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+		};
+	};
+
+	flexcom {
+		pinctrl_flx6_default: flx6-default {
+			atmel,pins =
+				<AT91_PIOA 24 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
+				<AT91_PIOA 25 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
+		};
+
+		pinctrl_flx7_default: flx7-default {
+			atmel,pins =
+				<AT91_PIOC 0 AT91_PERIPH_C AT91_PINCTRL_PULL_UP>,
+				<AT91_PIOC 1 AT91_PERIPH_C AT91_PINCTRL_PULL_UP>;
+		};
+	};
+
+	gpio-keys {
+		pinctrl_key_gpio_default: key-gpio-default {
+			atmel,pins = <AT91_PIOC 9 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+	};
+
+	i2s {
+		pinctrl_i2s_default: i2s-default {
+			atmel,pins =
+				<AT91_PIOB 26 AT91_PERIPH_D AT91_PINCTRL_NONE>,		/* I2SCK */
+				<AT91_PIOB 15 AT91_PERIPH_D AT91_PINCTRL_NONE>,		/* I2SWS */
+				<AT91_PIOB 16 AT91_PERIPH_D AT91_PINCTRL_NONE>,		/* I2SDIN */
+				<AT91_PIOB 17 AT91_PERIPH_D AT91_PINCTRL_NONE>,		/* I2SDOUT */
+				<AT91_PIOB 25 AT91_PERIPH_D AT91_PINCTRL_NONE>;		/* I2SMCK */
+		};
+	};
+
+	led-controller {
+		pinctrl_red_led_gpio_default: red-led-gpio-default {
+			atmel,pins = <AT91_PIOC 14 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+		pinctrl_green_led_gpio_default: green-led-gpio-default {
+			atmel,pins = <AT91_PIOC 21 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+		pinctrl_blue_led_gpio_default: blue-led-gpio-default {
+			atmel,pins = <AT91_PIOC 20 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+	};
+
+	sdmmc0 {
+		pinctrl_sdmmc0_default: sdmmc0-default {
+			atmel,pins =
+				<AT91_PIOA 2 AT91_PERIPH_A (AT91_PINCTRL_DRIVE_STRENGTH_HI | AT91_PINCTRL_SLEWRATE_ENA)>,				/* PA2 CK  periph A with pullup */
+				<AT91_PIOA 1 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI | AT91_PINCTRL_SLEWRATE_ENA)>,	/* PA1 CMD periph A with pullup */
+				<AT91_PIOA 0 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI | AT91_PINCTRL_SLEWRATE_ENA)>,	/* PA0 DAT0 periph A */
+				<AT91_PIOA 3 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI | AT91_PINCTRL_SLEWRATE_ENA)>,	/* PA3 DAT1 periph A with pullup */
+				<AT91_PIOA 4 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI | AT91_PINCTRL_SLEWRATE_ENA)>,	/* PA4 DAT2 periph A with pullup */
+				<AT91_PIOA 5 AT91_PERIPH_A (AT91_PINCTRL_PULL_UP | AT91_PINCTRL_DRIVE_STRENGTH_HI | AT91_PINCTRL_SLEWRATE_ENA)>;	/* PA5 DAT3 periph A with pullup */
+		};
+	};
+}; /* pinctrl */
+
+&poweroff {
+	debounce-delay-us = <976>;
+	status = "okay";
+
+	input@0 {
+		reg = <0>;
+	};
+};
+
+&rtt {
+	atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
+};
+
+&sdmmc0 {
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdmmc0_default>;
+	cd-gpios = <&pioA 23 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	status = "okay";
+};
+
+&slow_xtal {
+	clock-frequency = <32768>;
+};
+
+&tcb {
+	timer0: timer@0 {
+		compatible = "atmel,tcb-timer";
+		reg = <0>;
+	};
+
+	timer1: timer@1 {
+		compatible = "atmel,tcb-timer";
+		reg = <1>;
+	};
+};
+
+&trng {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/at91-sama5d27_som1.dtsi b/arch/arm/boot/dts/microchip/at91-sama5d27_som1.dtsi
index a4623cc67cc1..13c28e92b17e 100644
--- a/arch/arm/boot/dts/at91-sama5d27_som1.dtsi
+++ b/arch/arm/boot/dts/microchip/at91-sama5d27_som1.dtsi
@@ -15,7 +15,7 @@
 	compatible = "atmel,sama5d27-som1", "atmel,sama5d27", "atmel,sama5d2", "atmel,sama5";
 
 	aliases {
-		i2c0	= &i2c0;
+		i2c0 = &i2c0;
 	};
 
 	clocks {
@@ -43,7 +43,8 @@
 					#size-cells = <1>;
 					compatible = "jedec,spi-nor";
 					reg = <0>;
-					spi-max-frequency = <80000000>;
+					spi-max-frequency = <104000000>;
+					spi-cs-setup-delay-ns = <7>;
 					spi-tx-bus-width = <4>;
 					spi-rx-bus-width = <4>;
 					m25p,fast-read;
@@ -83,6 +84,8 @@
 			macb0: ethernet@f8008000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_macb0_default>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 				phy-mode = "rmii";
 
 				ethernet-phy@7 {
@@ -103,7 +106,7 @@
 				scl-gpios = <&pioA PIN_PD22 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 				status = "okay";
 
-				at24@50 {
+				eeprom@50 {
 					compatible = "atmel,24c02";
 					reg = <0x50>;
 					pagesize = <8>;
diff --git a/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts b/arch/arm/boot/dts/microchip/at91-sama5d27_som1_ek.dts
index 08f0d4b995ff..45edf6214cf7 100644
--- a/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts
+++ b/arch/arm/boot/dts/microchip/at91-sama5d27_som1_ek.dts
@@ -21,8 +21,8 @@
 		serial0 = &uart1;	/* DBGU */
 		serial1 = &uart4;	/* mikro BUS 1 */
 		serial2 = &uart2;	/* mikro BUS 2 */
-		i2c1	= &i2c1;
-		i2c2	= &i2c3;
+		i2c1 = &i2c1;
+		i2c2 = &i2c3;
 	};
 
 	chosen {
@@ -37,7 +37,7 @@
 			status = "okay";
 		};
 
-		usb1: ohci@400000 {
+		usb1: usb@400000 {
 			num-ports = <3>;
 			atmel,vbus-gpio = <0 /* &pioA PIN_PD20 GPIO_ACTIVE_HIGH */
 					   &pioA PIN_PA27 GPIO_ACTIVE_HIGH
@@ -48,13 +48,12 @@
 			status = "okay";
 		};
 
-		usb2: ehci@500000 {
+		usb2: usb@500000 {
 			status = "okay";
 		};
 
 		sdmmc0: sdio-host@a0000000 {
 			bus-width = <8>;
-			mmc-ddr-3_3v;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_sdmmc0_default>;
 			status = "okay";
@@ -139,7 +138,7 @@
 				};
 			};
 
-			shdwc@f8048010 {
+			poweroff@f8048010 {
 				debounce-delay-us = <976>;
 				atmel,wakeup-rtc-timer;
 
@@ -478,13 +477,13 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_key_gpio_default>;
 
-		pb4 {
+		button {
 			label = "USER";
 			gpios = <&pioA PIN_PA29 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_PROG1>;
@@ -498,17 +497,17 @@
 		pinctrl-0 = <&pinctrl_led_gpio_default>;
 		status = "okay"; /* Conflict with pwm0. */
 
-		red {
+		led-red {
 			label = "red";
 			gpios = <&pioA PIN_PA10 GPIO_ACTIVE_HIGH>;
 		};
 
-		green {
+		led-green {
 			label = "green";
 			gpios = <&pioA PIN_PB1 GPIO_ACTIVE_HIGH>;
 		};
 
-		blue {
+		led-blue {
 			label = "blue";
 			gpios = <&pioA PIN_PA31 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi b/arch/arm/boot/dts/microchip/at91-sama5d27_wlsom1.dtsi
index 21c86171e462..0417f53b3e96 100644
--- a/arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi
+++ b/arch/arm/boot/dts/microchip/at91-sama5d27_wlsom1.dtsi
@@ -31,6 +31,14 @@
 		};
 	};
 
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_MAIN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-wilc1000";
 		reset-gpios = <&pioA PIN_PA27 GPIO_ACTIVE_HIGH>;
@@ -67,17 +75,22 @@
 	scl-gpios = <&pioA PIN_PD20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 
-	mcp16502@5b {
+	pmic@5b {
 		compatible = "microchip,mcp16502";
 		reg = <0x5b>;
+		lvin-supply = <&reg_5v>;
+		pvin1-supply = <&reg_5v>;
+		pvin2-supply = <&reg_5v>;
+		pvin3-supply = <&reg_5v>;
+		pvin4-supply = <&reg_5v>;
 		status = "okay";
 		lpm-gpios = <&pioBU 0 GPIO_ACTIVE_LOW>;
 
 		regulators {
 			vdd_3v3: VDD_IO {
 				regulator-name = "VDD_IO";
-				regulator-min-microvolt = <1200000>;
-				regulator-max-microvolt = <3700000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
 				regulator-initial-mode = <2>;
 				regulator-allowed-modes = <2>, <4>;
 				regulator-always-on;
@@ -95,8 +108,8 @@
 
 			vddio_ddr: VDD_DDR {
 				regulator-name = "VDD_DDR";
-				regulator-min-microvolt = <600000>;
-				regulator-max-microvolt = <1850000>;
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
 				regulator-initial-mode = <2>;
 				regulator-allowed-modes = <2>, <4>;
 				regulator-always-on;
@@ -118,8 +131,8 @@
 
 			vdd_core: VDD_CORE {
 				regulator-name = "VDD_CORE";
-				regulator-min-microvolt = <600000>;
-				regulator-max-microvolt = <1850000>;
+				regulator-min-microvolt = <1250000>;
+				regulator-max-microvolt = <1250000>;
 				regulator-initial-mode = <2>;
 				regulator-allowed-modes = <2>, <4>;
 				regulator-always-on;
@@ -160,8 +173,8 @@
 
 			LDO1 {
 				regulator-name = "LDO1";
-				regulator-min-microvolt = <1200000>;
-				regulator-max-microvolt = <3700000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
 				regulator-always-on;
 
 				regulator-state-standby {
@@ -175,9 +188,8 @@
 
 			LDO2 {
 				regulator-name = "LDO2";
-				regulator-min-microvolt = <1200000>;
-				regulator-max-microvolt = <3700000>;
-				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
 
 				regulator-state-standby {
 					regulator-on-in-suspend;
@@ -194,6 +206,8 @@
 &macb0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_macb0_default>;
+	#address-cells = <1>;
+	#size-cells = <0>;
 	phy-mode = "rmii";
 
 	ethernet-phy@0 {
@@ -214,12 +228,13 @@
 	pinctrl-0 = <&pinctrl_qspi1_default>;
 	status = "disabled";
 
-	qspi1_flash: spi_flash@0 {
+	qspi1_flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
 		reg = <0>;
-		spi-max-frequency = <80000000>;
+		spi-max-frequency = <104000000>;
+		spi-cs-setup-delay-ns = <7>;
 		spi-rx-bus-width = <4>;
 		spi-tx-bus-width = <4>;
 		m25p,fast-read;
@@ -370,7 +385,7 @@
 
 	wilc: wifi@0 {
 		reg = <0>;
-		compatible = "microchip,wilc1000";
+		compatible = "microchip,wilc3000", "microchip,wilc1000";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_wilc_default>;
 		clocks = <&pmc PMC_TYPE_SYSTEM 9>;
diff --git a/arch/arm/boot/dts/at91-sama5d27_wlsom1_ek.dts b/arch/arm/boot/dts/microchip/at91-sama5d27_wlsom1_ek.dts
index c145c4e5ef58..35a933eec573 100644
--- a/arch/arm/boot/dts/at91-sama5d27_wlsom1_ek.dts
+++ b/arch/arm/boot/dts/microchip/at91-sama5d27_wlsom1_ek.dts
@@ -19,21 +19,20 @@
 		serial1 = &uart6;	/* BT */
 		serial2 = &uart5;	/* mikro BUS 2 */
 		serial3 = &uart3;	/* mikro BUS 1 */
-		i2c1	= &i2c1;
+		i2c1 = &i2c1;
 	};
 
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_key_gpio_default>;
-		status = "okay";
 
-		sw4 {
+		button-1 {
 			label = "USER BUTTON";
 			gpios = <&pioA PIN_PB2 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_PROG1>;
@@ -47,17 +46,17 @@
 		pinctrl-0 = <&pinctrl_led_gpio_default>;
 		status = "okay";
 
-		red {
+		led-red {
 			label = "red";
 			gpios = <&pioA PIN_PA6 GPIO_ACTIVE_HIGH>;
 		};
 
-		green {
+		led-green {
 			label = "green";
 			gpios = <&pioA PIN_PA7 GPIO_ACTIVE_HIGH>;
 		};
 
-		blue {
+		led-blue {
 			label = "blue";
 			gpios = <&pioA PIN_PA8 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
@@ -191,14 +190,14 @@
 &qspi1 {
 	status = "okay";
 
-	qspi1_flash: spi_flash@0 {
+	qspi1_flash: flash@0 {
 		status = "okay";
 	};
 };
 
 &sdmmc0 {
 	bus-width = <4>;
-	mmc-ddr-3_3v;
+	no-1-8-v;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_sdmmc0_default>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/microchip/at91-sama5d29_curiosity.dts b/arch/arm/boot/dts/microchip/at91-sama5d29_curiosity.dts
new file mode 100644
index 000000000000..7be215781549
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/at91-sama5d29_curiosity.dts
@@ -0,0 +1,614 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * at91-sama5d29_curiosity.dts - Device Tree file for SAMA5D29 Curiosity board
+ *
+ * Copyright (C) 2023 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Mihai Sain <mihai.sain@microchip.com>
+ *
+ */
+/dts-v1/;
+#include "sama5d29.dtsi"
+#include "sama5d2-pinfunc.h"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/mfd/atmel-flexcom.h>
+
+/ {
+	model = "Microchip SAMA5D29 Curiosity";
+	compatible = "microchip,sama5d29-curiosity", "atmel,sama5d29", "atmel,sama5d2", "atmel,sama5";
+
+	aliases {
+		serial0 = &uart0;	// debug
+		serial1 = &uart1;	// RPi
+		serial2 = &uart3;	// mikro BUS 2
+		serial3 = &uart4;	// mikro BUS 1
+		serial4 = &uart6;	// flx1 Bluetooth
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200 root=/dev/mmcblk0p2 rw rootwait";
+		stdout-path = "serial0:115200n8";
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <24000000>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_key_gpio_default>;
+
+		button-1 {
+			label = "USER BUTTON";
+			gpios = <&pioA PIN_PA17 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_PROG1>;
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_led_gpio_default>;
+		status = "okay";
+
+		led-red {
+			label = "red";
+			gpios = <&pioA PIN_PA7 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-green {
+			label = "green";
+			gpios = <&pioA PIN_PA8 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-blue {
+			label = "blue";
+			gpios = <&pioA PIN_PA9 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	memory@20000000 {
+		device_type = "memory";
+		reg = <0x20000000 0x20000000>;
+	};
+
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5V_MAIN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+};
+
+&adc {
+	vddana-supply = <&vdd_3v3>;
+	vref-supply = <&vdd_3v3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc_default &pinctrl_adtrg_default>;
+	status = "okay";
+};
+
+&can0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can0_default>;
+	status = "okay";
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1_default>;
+	status = "okay";
+};
+
+&flx1 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+	status = "okay";
+
+	uart6: serial@200 {
+		pinctrl-0 = <&pinctrl_flx1_default>;
+		pinctrl-names = "default";
+		atmel,use-dma-rx;
+		atmel,use-dma-tx;
+		status = "okay";
+	};
+};
+
+&flx4 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
+	status = "okay";
+
+	spi6: spi@400 {
+		dmas = <0>, <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rpi_spi>;
+		status = "okay";
+	};
+};
+
+&i2c0 {
+	dmas = <0>, <0>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c0_default>;
+	pinctrl-1 = <&pinctrl_i2c0_gpio>;
+	sda-gpios = <&pioA PIN_PB31 GPIO_ACTIVE_HIGH>;
+	scl-gpios = <&pioA PIN_PC0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	i2c-sda-hold-time-ns = <350>;
+	status = "okay";
+
+	pmic@5b {
+		compatible = "microchip,mcp16502";
+		reg = <0x5b>;
+		lvin-supply = <&reg_5v>;
+		pvin1-supply = <&reg_5v>;
+		pvin2-supply = <&reg_5v>;
+		pvin3-supply = <&reg_5v>;
+		pvin4-supply = <&reg_5v>;
+		status = "okay";
+		lpm-gpios = <&pioBU 0 GPIO_ACTIVE_LOW>;
+
+		regulators {
+			vdd_3v3: VDD_IO {
+				regulator-name = "VDD_IO";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-mode = <4>;
+				};
+			};
+
+			vddio_ddr: VDD_DDR {
+				regulator-name = "VDD_DDR";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1200000>;
+					regulator-changeable-in-suspend;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1200000>;
+					regulator-changeable-in-suspend;
+					regulator-mode = <4>;
+				};
+			};
+
+			vdd_core: VDD_CORE {
+				regulator-name = "VDD_CORE";
+				regulator-min-microvolt = <1250000>;
+				regulator-max-microvolt = <1250000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-mode = <4>;
+				};
+			};
+
+			vdd_ddr: VDD_OTHER {
+				regulator-name = "VDD_OTHER";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+					regulator-changeable-in-suspend;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+					regulator-changeable-in-suspend;
+					regulator-mode = <4>;
+				};
+			};
+
+			LDO1 {
+				regulator-name = "LDO1";
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+				};
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			LDO2 {
+				regulator-name = "LDO2";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+				};
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&i2c1 {
+	dmas = <0>, <0>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	i2c-analog-filter;
+	i2c-digital-filter;
+	i2c-digital-filter-width-ns = <35>;
+	sda-gpios = <&pioA PIN_PD4 GPIO_ACTIVE_HIGH>;
+	scl-gpios = <&pioA PIN_PD5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&pioA {
+	pinctrl_adc_default: adc-default {
+		pinmux = <PIN_PD25__GPIO>,
+			 <PIN_PD26__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_adtrg_default: adtrg-default {
+		pinmux = <PIN_PD31__ADTRG>;
+		bias-pull-up;
+	};
+
+	pinctrl_can0_default: can0-default {
+		pinmux = <PIN_PC10__CANTX0>,
+			 <PIN_PC11__CANRX0>;
+		bias-disable;
+	};
+
+	pinctrl_can1_default: can1-default {
+		pinmux = <PIN_PC26__CANTX1>,
+			 <PIN_PC27__CANRX1>;
+		bias-disable;
+	};
+
+	pinctrl_debug_uart: debug-uart {
+		pinmux = <PIN_PB26__URXD0>,
+			 <PIN_PB27__UTXD0>;
+		bias-disable;
+	};
+
+	pinctrl_flx1_default: flx1-default {
+		pinmux = <PIN_PA24__FLEXCOM1_IO0>,
+			 <PIN_PA23__FLEXCOM1_IO1>,
+			 <PIN_PA25__FLEXCOM1_IO3>,
+			 <PIN_PA26__FLEXCOM1_IO4>;
+		bias-disable;
+	};
+
+	pinctrl_i2c0_default: i2c0-default {
+		pinmux = <PIN_PB31__TWD0>,
+			 <PIN_PC0__TWCK0>;
+		bias-disable;
+	};
+
+	pinctrl_i2c0_gpio: i2c0-gpio-default {
+		pinmux = <PIN_PB31__GPIO>,
+			 <PIN_PC0__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_i2c1_default: i2c1-default {
+		pinmux = <PIN_PD4__TWD1>,
+			 <PIN_PD5__TWCK1>;
+		bias-disable;
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio-default {
+		pinmux = <PIN_PD4__GPIO>,
+			 <PIN_PD5__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_key_gpio_default: key-gpio-default {
+		pinmux = <PIN_PA17__GPIO>;
+		bias-pull-up;
+	};
+
+	pinctrl_led_gpio_default: led-gpio-default {
+		pinmux = <PIN_PA7__GPIO>,
+			 <PIN_PA8__GPIO>,
+			 <PIN_PA9__GPIO>;
+		bias-pull-up;
+	};
+
+	pinctrl_mikrobus1_pwm: mikrobus1-pwm {
+		pinmux = <PIN_PA31__PWML0>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus2_pwm: mikrobus2-pwm {
+		pinmux = <PIN_PB0__PWMH1>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus1_uart: mikrobus1-uart {
+		pinmux = <PIN_PB3__URXD4>,
+			 <PIN_PB4__UTXD4>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus2_uart: mikrobus2-uart {
+		pinmux = <PIN_PB11__URXD3>,
+			 <PIN_PB12__UTXD3>;
+		bias-disable;
+	};
+
+	pinctrl_qspi1_default: qspi1-default {
+		pinmux = <PIN_PB5__QSPI1_SCK>,
+			 <PIN_PB6__QSPI1_CS>,
+			 <PIN_PB7__QSPI1_IO0>,
+			 <PIN_PB8__QSPI1_IO1>,
+			 <PIN_PB9__QSPI1_IO2>,
+			 <PIN_PB10__QSPI1_IO3>;
+		bias-disable;
+	};
+
+	pinctrl_rpi_spi: rpi-spi {
+		pinmux = <PIN_PD12__FLEXCOM4_IO0>,
+			 <PIN_PD13__FLEXCOM4_IO1>,
+			 <PIN_PD14__FLEXCOM4_IO2>,
+			 <PIN_PD15__FLEXCOM4_IO3>,
+			 <PIN_PD16__FLEXCOM4_IO4>;
+		bias-disable;
+	};
+
+	pinctrl_rpi_uart: rpi-uart {
+		pinmux = <PIN_PD2__URXD1>,
+			 <PIN_PD3__UTXD1>;
+		bias-disable;
+	};
+
+	pinctrl_sdmmc0_default: sdmmc0-default {
+		pinmux = <PIN_PA0__SDMMC0_CK>,
+			 <PIN_PA1__SDMMC0_CMD>,
+			 <PIN_PA2__SDMMC0_DAT0>,
+			 <PIN_PA3__SDMMC0_DAT1>,
+			 <PIN_PA4__SDMMC0_DAT2>,
+			 <PIN_PA5__SDMMC0_DAT3>,
+			 <PIN_PA11__SDMMC0_VDDSEL>,
+			 <PIN_PA13__SDMMC0_CD>;
+		bias-disable;
+	};
+
+	pinctrl_sdmmc1_default: sdmmc1-default {
+		pinmux = <PIN_PA18__SDMMC1_DAT0>,
+			 <PIN_PA19__SDMMC1_DAT1>,
+			 <PIN_PA20__SDMMC1_DAT2>,
+			 <PIN_PA21__SDMMC1_DAT3>,
+			 <PIN_PA22__SDMMC1_CK>,
+			 <PIN_PA28__SDMMC1_CMD>,
+			 <PIN_PA30__SDMMC1_CD>;
+		bias-disable;
+	};
+
+	pinctrl_spi1_default: spi1-default {
+		pinmux = <PIN_PC1__SPI1_SPCK>,
+			 <PIN_PC2__SPI1_MOSI>,
+			 <PIN_PC3__SPI1_MISO>,
+			 <PIN_PC4__SPI1_NPCS0>,
+			 <PIN_PC5__SPI1_NPCS1>,
+			 <PIN_PC6__SPI1_NPCS2>,
+			 <PIN_PC7__SPI1_NPCS3>;
+		bias-disable;
+	};
+
+	pinctrl_usb_default: usb-default {
+		pinmux = <PIN_PA6__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_usba_vbus: usba-vbus {
+		pinmux = <PIN_PB13__GPIO>;
+		bias-disable;
+	};
+};
+
+&pwm0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_mikrobus1_pwm &pinctrl_mikrobus2_pwm>;
+	status = "okay";
+};
+
+&qspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_qspi1_default>;
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <80000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		m25p,fast-read;
+		label = "atmel_qspi1";
+		status = "okay";
+
+		at91bootstrap@0 {
+			label = "at91bootstrap";
+			reg = <0x0 0x40000>;
+		};
+
+		bootloader@40000 {
+			label = "bootloader";
+			reg = <0x40000 0xc0000>;
+		};
+
+		bootloaderenvred@100000 {
+			label = "bootloader env redundant";
+			reg = <0x100000 0x40000>;
+		};
+
+		bootloaderenv@140000 {
+			label = "bootloader env";
+			reg = <0x140000 0x40000>;
+		};
+
+		dtb@180000 {
+			label = "device tree";
+			reg = <0x180000 0x80000>;
+		};
+
+		kernel@200000 {
+			label = "kernel";
+			reg = <0x200000 0x600000>;
+		};
+	};
+};
+
+&sdmmc0 {
+	bus-width = <4>;
+	no-1-8-v;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdmmc0_default>;
+	disable-wp;
+	status = "okay";
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdmmc1_default>;
+	disable-wp;
+	status = "okay";
+};
+
+&shutdown_controller {
+	debounce-delay-us = <976>;
+	atmel,wakeup-rtc-timer;
+
+	input@0 {
+		reg = <0>;
+	};
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+	status = "okay";
+};
+
+&tcb0 {
+	timer0: timer@0 {
+		compatible = "atmel,tcb-timer";
+		reg = <0>;
+	};
+
+	timer1: timer@1 {
+		compatible = "atmel,tcb-timer";
+		reg = <1>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_debug_uart>;
+	atmel,use-dma-rx;
+	atmel,use-dma-tx;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rpi_uart>;
+	atmel,use-dma-rx;
+	atmel,use-dma-tx;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_mikrobus2_uart>;
+	atmel,use-dma-rx;
+	atmel,use-dma-tx;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_mikrobus1_uart>;
+	atmel,use-dma-rx;
+	atmel,use-dma-tx;
+	status = "okay";
+};
+
+&usb0 {
+	atmel,vbus-gpio = <&pioA PIN_PB13 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usba_vbus>;
+	status = "okay";
+};
+
+&usb1 {
+	num-ports = <3>;
+	atmel,vbus-gpio = <0
+			   &pioA PIN_PA6 GPIO_ACTIVE_HIGH
+			   0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_default>;
+	status = "okay";
+};
+
+&usb2 {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/at91-sama5d2_icp.dts b/arch/arm/boot/dts/microchip/at91-sama5d2_icp.dts
index 806eb1d911d7..fbae6a9af6c3 100644
--- a/arch/arm/boot/dts/at91-sama5d2_icp.dts
+++ b/arch/arm/boot/dts/microchip/at91-sama5d2_icp.dts
@@ -24,8 +24,8 @@
 		serial1 = &uart1;	/* mikro BUS 3 */
 		serial3 = &uart3;	/* mikro BUS 2 */
 		serial5 = &uart7;	/* flx2 */
-		i2c0	= &i2c0;
-		i2c1	= &i2c1;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
 	};
 
 	chosen {
@@ -42,14 +42,13 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_key_gpio_default>;
-		status = "okay";
 
-		sw4 {
+		button-1 {
 			label = "USER_PB1";
 			gpios = <&pioA PIN_PD0 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_PROG1>;
@@ -63,22 +62,30 @@
 		pinctrl-0 = <&pinctrl_led_gpio_default>;
 		status = "okay"; /* conflict with pwm0 */
 
-		red {
+		led-red {
 			label = "red";
 			gpios = <&pioA PIN_PB0 GPIO_ACTIVE_HIGH>;
 		};
 
-		green {
+		led-green {
 			label = "green";
 			gpios = <&pioA PIN_PB1 GPIO_ACTIVE_HIGH>;
 		};
 
-		blue {
+		led-blue {
 			label = "blue";
 			gpios = <&pioA PIN_PA31 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 	};
+
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_MAIN_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
 };
 
 &adc {
@@ -188,17 +195,53 @@
 		i2c-digital-filter-width-ns = <35>;
 		status = "okay";
 
-		mcp16502@5b {
+		power-monitor@10 {
+			compatible = "microchip,pac1934";
+			reg = <0x10>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@1 {
+				reg = <0x1>;
+				shunt-resistor-micro-ohms = <10000>;
+				label = "VDD3V3_1";
+			};
+
+			channel@2 {
+				reg = <0x2>;
+				shunt-resistor-micro-ohms = <10000>;
+				label = "VDD3V3_2";
+			};
+
+			channel@3 {
+				reg = <0x3>;
+				shunt-resistor-micro-ohms = <10000>;
+				label = "VDDCORE";
+			};
+
+			channel@4 {
+				reg = <0x4>;
+				shunt-resistor-micro-ohms = <10000>;
+				label = "VDDIODDR";
+			};
+		};
+
+		pmic@5b {
 			compatible = "microchip,mcp16502";
 			reg = <0x5b>;
+			lvin-supply = <&reg_5v>;
+			pvin1-supply = <&reg_5v>;
+			pvin2-supply = <&reg_5v>;
+			pvin3-supply = <&reg_5v>;
+			pvin4-supply = <&reg_5v>;
 			status = "okay";
 			lpm-gpios = <&pioBU 7 GPIO_ACTIVE_LOW>;
 
 			regulators {
 				vdd_io_reg: VDD_IO {
 					regulator-name = "VDD_IO";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <3700000>;
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
 					regulator-initial-mode = <2>;
 					regulator-allowed-modes = <2>, <4>;
 					regulator-always-on;
@@ -216,8 +259,8 @@
 
 				VDD_DDR {
 					regulator-name = "VDD_DDR";
-					regulator-min-microvolt = <600000>;
-					regulator-max-microvolt = <1850000>;
+					regulator-min-microvolt = <1350000>;
+					regulator-max-microvolt = <1350000>;
 					regulator-initial-mode = <2>;
 					regulator-allowed-modes = <2>, <4>;
 					regulator-always-on;
@@ -235,8 +278,8 @@
 
 				VDD_CORE {
 					regulator-name = "VDD_CORE";
-					regulator-min-microvolt = <600000>;
-					regulator-max-microvolt = <1850000>;
+					regulator-min-microvolt = <1250000>;
+					regulator-max-microvolt = <1250000>;
 					regulator-initial-mode = <2>;
 					regulator-allowed-modes = <2>, <4>;
 					regulator-always-on;
@@ -258,7 +301,6 @@
 					regulator-max-microvolt = <1850000>;
 					regulator-initial-mode = <2>;
 					regulator-allowed-modes = <2>, <4>;
-					regulator-always-on;
 
 					regulator-state-standby {
 						regulator-on-in-suspend;
@@ -273,8 +315,8 @@
 
 				LDO1 {
 					regulator-name = "LDO1";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <3700000>;
+					regulator-min-microvolt = <2500000>;
+					regulator-max-microvolt = <2500000>;
 					regulator-always-on;
 
 					regulator-state-standby {
@@ -288,8 +330,8 @@
 
 				LDO2 {
 					regulator-name = "LDO2";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <3700000>;
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
 					regulator-always-on;
 
 					regulator-state-standby {
@@ -329,21 +371,21 @@
 	status = "okay";
 
 	eeprom@50 {
-		compatible = "atmel,24c32";
+		compatible = "atmel,24c02";
 		reg = <0x50>;
 		pagesize = <16>;
 		status = "okay";
 	};
 
 	eeprom@52 {
-		compatible = "atmel,24c32";
+		compatible = "atmel,24c02";
 		reg = <0x52>;
 		pagesize = <16>;
 		status = "disabled";
 	};
 
 	eeprom@53 {
-		compatible = "atmel,24c32";
+		compatible = "atmel,24c02";
 		reg = <0x53>;
 		pagesize = <16>;
 		status = "disabled";
@@ -671,7 +713,8 @@
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
 		reg = <0>;
-		spi-max-frequency = <80000000>;
+		spi-max-frequency = <104000000>;
+		spi-cs-setup-delay-ns = <7>;
 		spi-tx-bus-width = <4>;
 		spi-rx-bus-width = <4>;
 		m25p,fast-read;
diff --git a/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts b/arch/arm/boot/dts/microchip/at91-sama5d2_ptc_ek.dts
index 8ed58af01391..10d69f6957cf 100644
--- a/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts
+++ b/arch/arm/boot/dts/microchip/at91-sama5d2_ptc_ek.dts
@@ -20,9 +20,9 @@
 
 	aliases {
 		serial0 = &uart0;	/* DBGU */
-		i2c0	= &i2c0;	/* mikroBUS 1 */
-		i2c1	= &i2c1;	/* XPRO EXT1 */
-		i2c2	= &i2c2;
+		i2c0 = &i2c0;	/* mikroBUS 1 */
+		i2c1 = &i2c1;	/* XPRO EXT1 */
+		i2c2 = &i2c2;
 	};
 
 	chosen {
@@ -47,7 +47,7 @@
 			status = "okay";
 		};
 
-		usb1: ohci@400000 {
+		usb1: usb@400000 {
 			num-ports = <3>;
 			atmel,vbus-gpio = <0
 					   &pioA PIN_PB12 GPIO_ACTIVE_HIGH
@@ -58,7 +58,7 @@
 			status = "okay";
 		};
 
-		usb2: ehci@500000 {
+		usb2: usb@500000 {
 			status = "okay";
 		};
 
@@ -139,6 +139,8 @@
 			macb0: ethernet@f8008000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 				phy-mode = "rmii";
 				status = "okay";
 
@@ -202,7 +204,7 @@
 				};
 			};
 
-			shdwc@f8048010 {
+			poweroff@f8048010 {
 				debounce-delay-us = <976>;
 
 				input@0 {
@@ -229,7 +231,7 @@
 				scl-gpios = <&pioA PIN_PC7 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 				status = "okay";
 
-				at24@50 {
+				eeprom@50 {
 					compatible = "atmel,24c02";
 					reg = <0x50>;
 					pagesize = <8>;
@@ -394,13 +396,13 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_key_gpio_default>;
 
-		bp1 {
+		button-1 {
 			label = "PB_USER";
 			gpios = <&pioA PIN_PA10 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_PROG1>;
@@ -414,17 +416,17 @@
 		pinctrl-0 = <&pinctrl_led_gpio_default>;
 		status = "okay";
 
-		red {
+		led-red {
 			label = "red";
 			gpios = <&pioA PIN_PB10 GPIO_ACTIVE_HIGH>;
 		};
 
-		green {
+		led-green {
 			label = "green";
 			gpios = <&pioA PIN_PB8 GPIO_ACTIVE_HIGH>;
 		};
 
-		blue {
+		led-blue {
 			label = "blue";
 			gpios = <&pioA PIN_PB6 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/microchip/at91-sama5d2_xplained.dts
index 9bf2ec0ba3e2..7e77a55ed41d 100644
--- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts
+++ b/arch/arm/boot/dts/microchip/at91-sama5d2_xplained.dts
@@ -46,7 +46,7 @@
 			status = "okay";
 		};
 
-		usb1: ohci@400000 {
+		usb1: usb@400000 {
 			num-ports = <3>;
 			atmel,vbus-gpio = <0 /* &pioA PIN_PB9 GPIO_ACTIVE_HIGH */
 					   &pioA PIN_PB10 GPIO_ACTIVE_HIGH
@@ -57,7 +57,7 @@
 			status = "okay";
 		};
 
-		usb2: ehci@500000 {
+		usb2: usb@500000 {
 			status = "okay";
 		};
 
@@ -137,7 +137,7 @@
 				pinctrl-0 = <&pinctrl_spi0_default>;
 				status = "okay";
 
-				m25p80@0 {
+				flash@0 {
 					compatible = "atmel,at25df321a";
 					reg = <0>;
 					spi-max-frequency = <50000000>;
@@ -147,6 +147,8 @@
 			macb0: ethernet@f8008000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 				phy-mode = "rmii";
 				status = "okay";
 
@@ -205,10 +207,10 @@
 
 							regulator-state-mem {
 								regulator-on-in-suspend;
-								regulator-suspend-min-microvolt=<1400000>;
-								regulator-suspend-max-microvolt=<1400000>;
+								regulator-suspend-min-microvolt = <1400000>;
+								regulator-suspend-max-microvolt = <1400000>;
 								regulator-changeable-in-suspend;
-								regulator-mode=<ACT8945A_REGULATOR_MODE_LOWPOWER>;
+								regulator-mode = <ACT8945A_REGULATOR_MODE_LOWPOWER>;
 							};
 						};
 
@@ -346,7 +348,7 @@
 				};
 			};
 
-			shdwc@f8048010 {
+			poweroff@f8048010 {
 				debounce-delay-us = <976>;
 				atmel,wakeup-rtc-timer;
 
@@ -409,7 +411,7 @@
 				scl-gpios = <&pioA PIN_PD5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 				status = "okay";
 
-				at24@54 {
+				eeprom@54 {
 					compatible = "atmel,24c02";
 					reg = <0x54>;
 					pagesize = <16>;
@@ -703,13 +705,13 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_key_gpio_default>;
 
-		bp1 {
+		button {
 			label = "PB_USER";
 			gpios = <&pioA PIN_PB9 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_PROG1>;
@@ -723,18 +725,18 @@
 		pinctrl-0 = <&pinctrl_led_gpio_default>;
 		status = "okay"; /* conflict with pwm0 */
 
-		red {
+		led-red {
 			label = "red";
 			gpios = <&pioA PIN_PB6 GPIO_ACTIVE_LOW>;
 		};
 
 
-		green {
+		led-green {
 			label = "green";
 			gpios = <&pioA PIN_PB5 GPIO_ACTIVE_LOW>;
 		};
 
-		blue {
+		led-blue {
 			label = "blue";
 			gpios = <&pioA PIN_PB0 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/microchip/at91-sama5d3_eds.dts b/arch/arm/boot/dts/microchip/at91-sama5d3_eds.dts
new file mode 100644
index 000000000000..c287b03d768b
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/at91-sama5d3_eds.dts
@@ -0,0 +1,307 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * at91-sama5d3_eds.dts - Device Tree file for the SAMA5D3 Ethernet
+ *    Development System board.
+ *
+ * Copyright (C) 2022 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Jerry Ray <jerry.ray@microchip.com>
+ */
+/dts-v1/;
+#include "sama5d36.dtsi"
+
+/ {
+	model = "SAMA5D3 Ethernet Development System";
+	compatible = "microchip,sama5d3-eds", "atmel,sama5d36",
+		     "atmel,sama5d3", "atmel,sama5";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_key_gpio>;
+
+		button-3 {
+			label = "PB_USER";
+			gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
+			linux,code = <0x104>;
+			wakeup-source;
+		};
+	};
+
+	memory@20000000 {
+		reg = <0x20000000 0x10000000>;
+	};
+
+	vcc_3v3_reg: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	vcc_2v5_reg: regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_2V5";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+		vin-supply = <&vcc_3v3_reg>;
+	};
+
+	vcc_1v8_reg: regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		vin-supply = <&vcc_3v3_reg>;
+	};
+
+	vcc_1v2_reg: regulator-4 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_1V2";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-always-on;
+	};
+
+	vcc_mmc0_reg: regulator-5 {
+		compatible = "regulator-fixed";
+		regulator-name = "mmc0-card-supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_vcc_mmc0_reg_gpio>;
+		gpio = <&pioE 2 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&can0 {
+	status = "okay";
+};
+
+&dbgu {
+	status = "okay";
+};
+
+&ebi {
+	pinctrl-0 = <&pinctrl_ebi_nand_addr>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	nand_controller: nand-controller {
+		status = "okay";
+
+		nand@3 {
+			reg = <0x3 0x0 0x2>;
+			atmel,rb = <0>;
+			nand-bus-width = <8>;
+			nand-ecc-mode = "hw";
+			nand-ecc-strength = <4>;
+			nand-ecc-step-size = <512>;
+			nand-on-flash-bbt;
+			label = "atmel_nand";
+
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				at91bootstrap@0 {
+					label = "at91bootstrap";
+					reg = <0x0 0x40000>;
+				};
+
+				bootloader@40000 {
+					label = "bootloader";
+					reg = <0x40000 0xc0000>;
+				};
+
+				bootloaderenvred@100000 {
+					label = "bootloader env redundant";
+					reg = <0x100000 0x40000>;
+				};
+
+				bootloaderenv@140000 {
+					label = "bootloader env";
+					reg = <0x140000 0x40000>;
+				};
+
+				dtb@180000 {
+					label = "device tree";
+					reg = <0x180000 0x80000>;
+				};
+
+				kernel@200000 {
+					label = "kernel";
+					reg = <0x200000 0x600000>;
+				};
+
+				rootfs@800000 {
+					label = "rootfs";
+					reg = <0x800000 0x0f800000>;
+				};
+			};
+		};
+	};
+};
+
+&i2c0 {
+	pinctrl-0 = <&pinctrl_i2c0_pu>;
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-0 = <&pinctrl_i2c2_pu>;
+	status = "okay";
+};
+
+&main_xtal {
+	clock-frequency = <12000000>;
+};
+
+&mmc0 {
+	pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3
+		     &pinctrl_mmc0_dat4_7 &pinctrl_mmc0_cd>;
+	vmmc-supply = <&vcc_mmc0_reg>;
+	vqmmc-supply = <&vcc_3v3_reg>;
+	status = "okay";
+	slot@0 {
+		reg = <0>;
+		bus-width = <8>;
+		cd-gpios = <&pioE 0 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&pinctrl {
+	board {
+		pinctrl_i2c0_pu: i2c0-pu {
+			atmel,pins =
+				<AT91_PIOA 30 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
+				<AT91_PIOA 31 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
+		};
+
+		pinctrl_i2c2_pu: i2c2-pu {
+			atmel,pins =
+				<AT91_PIOA 18 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>,
+				<AT91_PIOA 19 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>;
+		};
+
+		pinctrl_key_gpio: key-gpio-0 {
+			atmel,pins =
+				<AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+		};
+
+		pinctrl_mmc0_cd: mmc0-cd {
+			atmel,pins =
+				<AT91_PIOE 0 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+		};
+
+		/* Reserved for reset signal to the RGMII connector. */
+		pinctrl_rgmii_rstn: rgmii-rstn {
+			atmel,pins =
+				<AT91_PIOD 18 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+		};
+
+		/* Reserved for an interrupt line from the RMII and RGMII connectors. */
+		pinctrl_spi_irqn: spi-irqn {
+			atmel,pins =
+				<AT91_PIOB 28 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+		};
+
+		pinctrl_spi0_cs: spi0-cs-default {
+			atmel,pins =
+				<AT91_PIOD 13 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+				 AT91_PIOD 16 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_spi1_cs: spi1-cs-default {
+			atmel,pins = <AT91_PIOC 25 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+				      AT91_PIOC 28 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_usba_vbus: usba-vbus {
+			atmel,pins =
+				<AT91_PIOE 9 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+		};
+
+		pinctrl_usb_default: usb-default {
+			atmel,pins =
+				<AT91_PIOE 3 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+				 AT91_PIOE 4 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+
+		/* Reserved for VBUS fault interrupt. */
+		pinctrl_vbusfault_irqn: vbusfault-irqn {
+			atmel,pins =
+				<AT91_PIOE 5 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+		};
+
+		pinctrl_vcc_mmc0_reg_gpio: vcc-mmc0-reg-gpio-default {
+			atmel,pins = <AT91_PIOE 2 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
+		};
+	};
+};
+
+&slow_xtal {
+	clock-frequency = <32768>;
+};
+
+&spi0 {
+	pinctrl-names = "default", "cs";
+	pinctrl-1 = <&pinctrl_spi0_cs>;
+	cs-gpios = <&pioD 13 0>, <0>, <0>, <&pioD 16 0>;
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-names = "default", "cs";
+	pinctrl-1 = <&pinctrl_spi1_cs>;
+	cs-gpios = <&pioC 25 0>, <0>, <0>, <&pioC 28 0>;
+	status = "okay";
+};
+
+&tcb0 {
+	timer0: timer@0 {
+		compatible = "atmel,tcb-timer";
+		reg = <0>;
+	};
+
+	timer1: timer@1 {
+		compatible = "atmel,tcb-timer";
+		reg = <1>;
+	};
+};
+
+&usb0 {	/* USB Device port with VBUS detection. */
+	atmel,vbus-gpio = <&pioE 9 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usba_vbus>;
+	status = "okay";
+};
+
+&usb1 {	/* 3-port Host. First port is unused. */
+	atmel,vbus-gpio = <0
+			   &pioE 3 GPIO_ACTIVE_HIGH
+			   &pioE 4 GPIO_ACTIVE_HIGH
+			  >;
+	num-ports = <3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_default>;
+	status = "okay";
+};
+
+&usb2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/at91-sama5d3_ksz9477_evb.dts b/arch/arm/boot/dts/microchip/at91-sama5d3_ksz9477_evb.dts
index 443e8b022897..b66570080894 100644
--- a/arch/arm/boot/dts/at91-sama5d3_ksz9477_evb.dts
+++ b/arch/arm/boot/dts/microchip/at91-sama5d3_ksz9477_evb.dts
@@ -120,26 +120,31 @@
 			port@0 {
 				reg = <0>;
 				label = "lan1";
+				phy-mode = "internal";
 			};
 
 			port@1 {
 				reg = <1>;
 				label = "lan2";
+				phy-mode = "internal";
 			};
 
 			port@2 {
 				reg = <2>;
 				label = "lan3";
+				phy-mode = "internal";
 			};
 
 			port@3 {
 				reg = <3>;
 				label = "lan4";
+				phy-mode = "internal";
 			};
 
 			port@4 {
 				reg = <4>;
 				label = "lan5";
+				phy-mode = "internal";
 			};
 
 			port@5 {
@@ -147,6 +152,7 @@
 				label = "cpu";
 				ethernet = <&macb0>;
 				phy-mode = "rgmii-txid";
+				tx-internal-delay-ps = <2000>;
 
 				fixed-link {
 					speed = <1000>;
@@ -157,6 +163,18 @@
 	};
 };
 
+&tcb0 {
+	timer0: timer@0 {
+		compatible = "atmel,tcb-timer";
+		reg = <0>;
+	};
+
+	timer1: timer@1 {
+		compatible = "atmel,tcb-timer";
+		reg = <1>;
+	};
+};
+
 &usb0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usba_vbus>;
diff --git a/arch/arm/boot/dts/at91-sama5d3_xplained.dts b/arch/arm/boot/dts/microchip/at91-sama5d3_xplained.dts
index d72c042f2850..d2c43957497d 100644
--- a/arch/arm/boot/dts/at91-sama5d3_xplained.dts
+++ b/arch/arm/boot/dts/microchip/at91-sama5d3_xplained.dts
@@ -57,8 +57,8 @@
 			};
 
 			spi0: spi@f0004000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pinctrl_spi0_cs>;
+				pinctrl-names = "default", "cs";
+				pinctrl-1 = <&pinctrl_spi0_cs>;
 				cs-gpios = <&pioD 13 0>, <0>, <0>, <&pioD 16 0>;
 				status = "okay";
 			};
@@ -87,7 +87,7 @@
 			i2c1: i2c@f0018000 {
 				status = "okay";
 
-				pmic: act8865@5b {
+				act8865: pmic@5b {
 					compatible = "active-semi,act8865";
 					reg = <0x5b>;
 					status = "disabled";
@@ -171,8 +171,8 @@
 			};
 
 			spi1: spi@f8008000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pinctrl_spi1_cs>;
+				pinctrl-names = "default", "cs";
+				pinctrl-1 = <&pinctrl_spi1_cs>;
 				cs-gpios = <&pioC 25 0>;
 				status = "okay";
 			};
@@ -283,7 +283,7 @@
 			status = "okay";
 		};
 
-		usb1: ohci@600000 {
+		usb1: usb@600000 {
 			num-ports = <3>;
 			atmel,vbus-gpio = <0
 					   &pioE 3 GPIO_ACTIVE_LOW
@@ -294,7 +294,7 @@
 			status = "okay";
 		};
 
-		usb2: ehci@700000 {
+		usb2: usb@700000 {
 			status = "okay";
 		};
 
@@ -372,13 +372,13 @@
 		regulator-always-on;
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_key_gpio>;
 
-		bp3 {
+		button {
 			label = "PB_USER";
 			gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_PROG1>;
@@ -392,13 +392,13 @@
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 		status = "okay";
 
-		d2 {
+		led-d2 {
 			label = "d2";
 			gpios = <&pioE 23 GPIO_ACTIVE_LOW>;	/* PE23, conflicts with A23, CTS2 */
 			linux,default-trigger = "heartbeat";
 		};
 
-		d3 {
+		led-d3 {
 			label = "d3"; /* Conflict with EBI CS0, USART2 CTS. */
 			gpios = <&pioE 24 GPIO_ACTIVE_HIGH>;
 		};
diff --git a/arch/arm/boot/dts/at91-sama5d4_ma5d4.dtsi b/arch/arm/boot/dts/microchip/at91-sama5d4_ma5d4.dtsi
index 710cb72bda5a..fd1086f52b40 100644
--- a/arch/arm/boot/dts/at91-sama5d4_ma5d4.dtsi
+++ b/arch/arm/boot/dts/microchip/at91-sama5d4_ma5d4.dtsi
@@ -49,7 +49,7 @@
 				cs-gpios = <&pioC 3 0>, <0>, <0>, <0>;
 				status = "okay";
 
-				m25p80@0 {
+				flash@0 {
 					compatible = "atmel,at25df321a";
 					spi-max-frequency = <50000000>;
 					reg = <0>;
diff --git a/arch/arm/boot/dts/at91-sama5d4_ma5d4evk.dts b/arch/arm/boot/dts/microchip/at91-sama5d4_ma5d4evk.dts
index 4d7cee569ff2..b9725e400501 100644
--- a/arch/arm/boot/dts/at91-sama5d4_ma5d4evk.dts
+++ b/arch/arm/boot/dts/microchip/at91-sama5d4_ma5d4evk.dts
@@ -22,7 +22,7 @@
 			status = "okay";
 		};
 
-		usb1: ohci@500000 {
+		usb1: usb@500000 {
 			num-ports = <3>;
 			atmel,vbus-gpio = <0
 					   &pioE 11 GPIO_ACTIVE_LOW
@@ -31,7 +31,7 @@
 			status = "okay";
 		};
 
-		usb2: ehci@600000 {
+		usb2: usb@600000 {
 			status = "okay";
 		};
 
@@ -115,19 +115,19 @@
 		compatible = "gpio-leds";
 		status = "okay";
 
-		user1 {
+		led-user1 {
 			label = "user1";
 			gpios = <&pioD 28 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 
-		user2 {
+		led-user2 {
 			label = "user2";
 			gpios = <&pioD 29 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 
-		user3 {
+		led-user3 {
 			label = "user3";
 			gpios = <&pioD 30 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/at91-sama5d4_xplained.dts b/arch/arm/boot/dts/microchip/at91-sama5d4_xplained.dts
index d241c24f0d83..0ecccb9a809d 100644
--- a/arch/arm/boot/dts/at91-sama5d4_xplained.dts
+++ b/arch/arm/boot/dts/microchip/at91-sama5d4_xplained.dts
@@ -81,8 +81,8 @@
 			};
 
 			spi1: spi@fc018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pinctrl_spi0_cs>;
+				pinctrl-names = "default", "cs";
+				pinctrl-1 = <&pinctrl_spi1_cs>;
 				cs-gpios = <&pioB 21 0>;
 				status = "okay";
 			};
@@ -140,7 +140,7 @@
 						atmel,pins =
 							<AT91_PIOE 1 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
 					};
-					pinctrl_spi0_cs: spi0_cs_default {
+					pinctrl_spi1_cs: spi1_cs_default {
 						atmel,pins =
 							<AT91_PIOB 21 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
 					};
@@ -164,7 +164,7 @@
 			status = "okay";
 		};
 
-		usb1: ohci@500000 {
+		usb1: usb@500000 {
 			num-ports = <3>;
 			atmel,vbus-gpio = <0
 					   &pioE 11 GPIO_ACTIVE_HIGH
@@ -175,7 +175,7 @@
 			status = "okay";
 		};
 
-		usb2: ehci@600000 {
+		usb2: usb@600000 {
 			status = "okay";
 		};
 
@@ -242,13 +242,13 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_key_gpio>;
 
-		pb_user1 {
+		button {
 			label = "pb_user1";
 			gpios = <&pioE 8 GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_PROG1>;
@@ -262,13 +262,13 @@
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 		status = "okay";
 
-		d8 {
+		led-d8 {
 			label = "d8";
 			gpios = <&pioD 30 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 		};
 
-		d10 {
+		led-d10 {
 			label = "d10";
 			gpios = <&pioE 15 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/at91-sama5d4ek.dts b/arch/arm/boot/dts/microchip/at91-sama5d4ek.dts
index fe432b6b7e95..69107d6cd26c 100644
--- a/arch/arm/boot/dts/at91-sama5d4ek.dts
+++ b/arch/arm/boot/dts/microchip/at91-sama5d4ek.dts
@@ -65,7 +65,7 @@
 			spi0: spi@f8010000 {
 				cs-gpios = <&pioC 3 0>, <0>, <0>, <0>;
 				status = "okay";
-				m25p80@0 {
+				flash@0 {
 					compatible = "atmel,at25df321a";
 					spi-max-frequency = <50000000>;
 					reg = <0>;
@@ -198,7 +198,7 @@
 			status = "okay";
 		};
 
-		usb1: ohci@500000 {
+		usb1: usb@500000 {
 			num-ports = <3>;
 			atmel,vbus-gpio = <0 /* &pioE 10 GPIO_ACTIVE_LOW */
 					   &pioE 11 GPIO_ACTIVE_LOW
@@ -207,7 +207,7 @@
 			status = "okay";
 		};
 
-		usb2: ehci@600000 {
+		usb2: usb@600000 {
 			status = "okay";
 		};
 
@@ -269,13 +269,13 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_key_gpio>;
 
-		pb_user1 {
+		button {
 			label = "pb_user1";
 			gpios = <&pioE 13 GPIO_ACTIVE_HIGH>;
 			linux,code = <0x100>;
@@ -287,18 +287,18 @@
 		compatible = "gpio-leds";
 		status = "okay";
 
-		d8 {
+		led-d8 {
 			label = "d8";
 			/* PE28, conflicts with usart4 rts pin */
 			gpios = <&pioE 28 GPIO_ACTIVE_LOW>;
 		};
 
-		d9 {
+		led-d9 {
 			label = "d9";
 			gpios = <&pioE 9 GPIO_ACTIVE_HIGH>;
 		};
 
-		d10 {
+		led-d10 {
 			label = "d10";
 			gpios = <&pioE 8 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/microchip/at91-sama7d65_curiosity.dts b/arch/arm/boot/dts/microchip/at91-sama7d65_curiosity.dts
new file mode 100644
index 000000000000..927c27260b6c
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/at91-sama7d65_curiosity.dts
@@ -0,0 +1,459 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ *  at91-sama7d65_curiosity.dts - Device Tree file for SAMA7D65 Curiosity board
+ *
+ *  Copyright (c) 2024 Microchip Technology Inc. and its subsidiaries
+ *
+ *  Author: Romain Sioen <romain.sioen@microchip.com>
+ *
+ */
+/dts-v1/;
+#include "sama7d65-pinfunc.h"
+#include "sama7d65.dtsi"
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/at91.h>
+
+/ {
+	model = "Microchip SAMA7D65 Curiosity";
+	compatible = "microchip,sama7d65-curiosity", "microchip,sama7d65",
+		     "microchip,sama7d6", "microchip,sama7";
+
+	aliases {
+		serial0 = &uart6;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_key_gpio_default>;
+
+		button {
+			label = "PB_USER";
+			gpios = <&pioa PIN_PC10 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_PROG1>;
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_led_gpio_default>;
+
+		led0: led-red {
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&pioa PIN_PB17 GPIO_ACTIVE_HIGH>; /* Conflict with pwm. */
+		};
+
+		led1: led-green {
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pioa PIN_PB15 GPIO_ACTIVE_HIGH>; /* Conflict with pwm. */
+		};
+
+		led2: led-blue {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_HEARTBEAT;
+			gpios = <&pioa PIN_PA21 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	memory@60000000 {
+		device_type = "memory";
+		reg = <0x60000000 0x40000000>;
+	};
+
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5V_MAIN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1_default>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can2_default>;
+	status = "okay";
+};
+
+&can3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can3_default>;
+	status = "okay";
+};
+
+&dma0 {
+	status = "okay";
+};
+
+&dma1 {
+	status = "okay";
+};
+
+&dma2 {
+	status = "okay";
+};
+
+&flx6 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+	status = "okay";
+};
+
+&uart6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart6_default>;
+	status = "okay";
+};
+
+&flx10 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+};
+
+&gmac0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gmac0_default
+		     &pinctrl_gmac0_mdio_default
+		     &pinctrl_gmac0_txck_default
+		     &pinctrl_gmac0_phy_irq>;
+	phy-mode = "rgmii-id";
+	nvmem-cells = <&eeprom0_eui48>;
+	nvmem-cell-names = "mac-address";
+	status = "okay";
+
+	ethernet-phy@7 {
+		reg = <0x7>;
+		interrupt-parent = <&pioa>;
+		interrupts = <PIN_PC1 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&i2c10 {
+	dmas = <0>, <0>;
+	i2c-analog-filter;
+	i2c-digital-filter;
+	i2c-digital-filter-width-ns = <35>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c10_default>;
+	status = "okay";
+
+	power-monitor@10 {
+		compatible = "microchip,pac1934";
+		reg = <0x10>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@1 {
+			reg = <0x1>;
+			shunt-resistor-micro-ohms = <47000>;
+			label = "VDD3V3";
+		};
+
+		channel@2 {
+			reg = <0x2>;
+			shunt-resistor-micro-ohms = <47000>;
+			label = "VDDIODDR";
+		};
+
+		channel@3 {
+			reg = <0x3>;
+			shunt-resistor-micro-ohms = <47000>;
+			label = "VDDCORE";
+		};
+
+		channel@4 {
+			reg = <0x4>;
+			shunt-resistor-micro-ohms = <47000>;
+			label = "VDDCPU";
+		};
+	};
+
+	pmic@5b {
+		compatible = "microchip,mcp16502";
+		reg = <0x5b>;
+		lvin-supply = <&reg_5v>;
+		pvin1-supply = <&reg_5v>;
+		pvin2-supply = <&reg_5v>;
+		pvin3-supply = <&reg_5v>;
+		pvin4-supply = <&reg_5v>;
+		status = "okay";
+
+		regulators {
+			vdd_3v3: VDD_IO {
+				regulator-name = "VDD_IO";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-mode = <4>;
+				};
+			};
+
+			vddioddr: VDD_DDR {
+				regulator-name = "VDD_DDR";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1350000>;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1350000>;
+					regulator-mode = <4>;
+				};
+			};
+
+			vddcore: VDD_CORE {
+				regulator-name = "VDD_CORE";
+				regulator-min-microvolt = <1050000>;
+				regulator-max-microvolt = <1050000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1050000>;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-mode = <4>;
+				};
+			};
+
+			vddcpu: VDD_OTHER {
+				regulator-name = "VDD_OTHER";
+				regulator-min-microvolt = <1050000>;
+				regulator-max-microvolt = <1250000>;
+				regulator-initial-mode = <2>;
+				regulator-allowed-modes = <2>, <4>;
+				regulator-ramp-delay = <3125>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1050000>;
+					regulator-mode = <4>;
+				};
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-mode = <4>;
+				};
+			};
+
+			vldo1: LDO1 {
+				regulator-name = "LDO1";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+
+				regulator-state-standby {
+					regulator-suspend-microvolt = <1800000>;
+					regulator-on-in-suspend;
+				};
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vldo2: LDO2 {
+				regulator-name = "LDO2";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3700000>;
+
+				regulator-state-standby {
+					regulator-on-in-suspend;
+				};
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+
+	eeprom0: eeprom@51 {
+		compatible = "microchip,24aa025e48";
+		reg = <0x51>;
+		size = <256>;
+		pagesize = <16>;
+		vcc-supply = <&vdd_3v3>;
+
+		nvmem-layout {
+			compatible = "fixed-layout";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			eeprom0_eui48: eui48@fa {
+				reg = <0xfa 0x6>;
+			};
+		};
+	};
+};
+
+&main_xtal {
+	clock-frequency = <24000000>;
+};
+
+&pioa {
+	pinctrl_can1_default: can1-default {
+		pinmux = <PIN_PD10__CANTX1>,
+			 <PIN_PD11__CANRX1>;
+		bias-disable;
+	};
+
+	pinctrl_can2_default: can2-default {
+		pinmux = <PIN_PD12__CANTX2>,
+			 <PIN_PD13__CANRX2>;
+		bias-disable;
+	};
+
+	pinctrl_can3_default: can3-default {
+		pinmux = <PIN_PD14__CANTX3>,
+			 <PIN_PD15__CANRX3>;
+		bias-disable;
+	};
+
+	pinctrl_gmac0_default: gmac0-default {
+		pinmux = <PIN_PA26__G0_TX0>,
+			 <PIN_PA27__G0_TX1>,
+			 <PIN_PB4__G0_TX2>,
+			 <PIN_PB5__G0_TX3>,
+			 <PIN_PA29__G0_RX0>,
+			 <PIN_PA30__G0_RX1>,
+			 <PIN_PB2__G0_RX2>,
+			 <PIN_PB6__G0_RX3>,
+			 <PIN_PA25__G0_TXCTL>,
+			 <PIN_PB3__G0_RXCK>,
+			 <PIN_PA28__G0_RXCTL>;
+		slew-rate = <0>;
+		bias-disable;
+	};
+
+	pinctrl_gmac0_mdio_default: gmac0-mdio-default {
+		pinmux = <PIN_PA31__G0_MDC>,
+			 <PIN_PB0__G0_MDIO>;
+		bias-disable;
+	};
+
+	pinctrl_gmac0_phy_irq: gmac0-phy-irq {
+		pinmux = <PIN_PC1__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_gmac0_txck_default: gmac0-txck-default {
+		pinmux = <PIN_PB1__G0_REFCK>;
+		slew-rate = <0>;
+		bias-pull-up;
+	};
+
+	pinctrl_i2c10_default: i2c10-default {
+		pinmux = <PIN_PB19__FLEXCOM10_IO1>,
+			 <PIN_PB20__FLEXCOM10_IO0>;
+		bias-pull-up;
+	};
+
+	pinctrl_key_gpio_default: key-gpio-default {
+		pinmux = <PIN_PC10__GPIO>;
+		bias-pull-up;
+	};
+
+	pinctrl_led_gpio_default: led-gpio-default {
+		pinmux = <PIN_PB15__GPIO>,
+			 <PIN_PB17__GPIO>,
+			 <PIN_PA21__GPIO>;
+		bias-pull-up;
+	};
+
+	pinctrl_sdmmc1_default: sdmmc1-default {
+		cmd-data {
+			pinmux = <PIN_PB22__SDMMC1_CMD>,
+				 <PIN_PB24__SDMMC1_DAT0>,
+				 <PIN_PB25__SDMMC1_DAT1>,
+				 <PIN_PB26__SDMMC1_DAT2>,
+				 <PIN_PB27__SDMMC1_DAT3>;
+			slew-rate = <0>;
+			bias-disable;
+		};
+
+		ck-cd-rstn-vddsel {
+			pinmux = <PIN_PB23__SDMMC1_CK>,
+				 <PIN_PB21__SDMMC1_RSTN>,
+				 <PIN_PB30__SDMMC1_1V8SEL>,
+				 <PIN_PB29__SDMMC1_CD>,
+				 <PIN_PB28__SDMMC1_WP>;
+			slew-rate = <0>;
+			bias-disable;
+		};
+	};
+
+	pinctrl_uart6_default: uart6-default {
+		pinmux = <PIN_PD18__FLEXCOM6_IO0>,
+			 <PIN_PD19__FLEXCOM6_IO1>;
+		bias-disable;
+	};
+};
+
+&rtt {
+	atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	no-1-8-v;
+	sdhci-caps-mask = <0x0 0x00200000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdmmc1_default>;
+	status = "okay";
+};
+
+&shdwc {
+	debounce-delay-us = <976>;
+	status = "okay";
+
+	input@0 {
+		reg = <0>;
+	};
+};
+
+&slow_xtal {
+	clock-frequency = <32768>;
+};
diff --git a/arch/arm/boot/dts/microchip/at91-sama7g54_curiosity.dts b/arch/arm/boot/dts/microchip/at91-sama7g54_curiosity.dts
new file mode 100644
index 000000000000..eb5f27ce1942
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/at91-sama7g54_curiosity.dts
@@ -0,0 +1,558 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * at91-sama7g54_curiosity.dts - Device Tree file for SAMA7G54 Curiosity Board
+ *
+ * Copyright (C) 2024 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Mihai Sain <mihai.sain@microchip.com>
+ *
+ */
+/dts-v1/;
+#include "sama7g5-pinfunc.h"
+#include "sama7g5.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/pinctrl/at91.h>
+
+/ {
+	model = "Microchip SAMA7G54 Curiosity";
+	compatible = "microchip,sama7g54-curiosity", "microchip,sama7g5", "microchip,sama7";
+
+	aliases {
+		serial0 = &uart3;
+		i2c0 = &i2c10;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_key_gpio_default>;
+
+		button-user {
+			label = "user-button";
+			gpios = <&pioA PIN_PD19 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_PROG1>;
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_led_gpio_default>;
+
+		led-red {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&pioA PIN_PD13 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-green {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_BOOT;
+			gpios = <&pioA PIN_PD14 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-blue {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_CPU;
+			gpios = <&pioA PIN_PB15 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	memory@60000000 {
+		device_type = "memory";
+		reg = <0x60000000 0x10000000>; /* 256 MiB DDR3L-1066 16-bit */
+	};
+
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5V_MAIN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+};
+
+&adc {
+	vddana-supply = <&vddout25>;
+	vref-supply = <&vddout25>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_mikrobus1_an_default &pinctrl_mikrobus2_an_default>;
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&vddcpu>;
+};
+
+&dma0 {
+	status = "okay";
+};
+
+&dma1 {
+	status = "okay";
+};
+
+&dma2 {
+	status = "okay";
+};
+
+&ebi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_nand_default>;
+	status = "okay";
+
+	nand_controller: nand-controller {
+		status = "okay";
+
+		nand@3 {
+			reg = <0x3 0x0 0x800000>;
+			atmel,rb = <0>;
+			nand-bus-width = <8>;
+			nand-ecc-mode = "hw";
+			nand-ecc-strength = <8>;
+			nand-ecc-step-size = <512>;
+			nand-on-flash-bbt;
+			label = "nand";
+
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				at91bootstrap@0 {
+					label = "nand: at91bootstrap";
+					reg = <0x0 0x40000>;
+				};
+
+				bootloader@40000 {
+					label = "nand: u-boot";
+					reg = <0x40000 0x100000>;
+				};
+
+				bootloaderenv@140000 {
+					label = "nand: u-boot env";
+					reg = <0x140000 0x40000>;
+				};
+
+				dtb@180000 {
+					label = "nand: device tree";
+					reg = <0x180000 0x80000>;
+				};
+
+				kernel@200000 {
+					label = "nand: kernel";
+					reg = <0x200000 0x600000>;
+				};
+
+				rootfs@800000 {
+					label = "nand: rootfs";
+					reg = <0x800000 0x1f800000>;
+				};
+			};
+		};
+	};
+};
+
+&flx3 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+	status = "okay";
+
+	uart3: serial@200 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_flx3_default>;
+		status = "okay";
+	};
+};
+
+&flx10 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+
+	i2c10: i2c@600 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_flx10_default>;
+		i2c-analog-filter;
+		i2c-digital-filter;
+		i2c-digital-filter-width-ns = <35>;
+		status = "okay";
+
+		power-monitor@1f {
+			compatible = "microchip,pac1934";
+			reg = <0x1f>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@1 {
+				reg = <0x1>;
+				shunt-resistor-micro-ohms = <47000>;
+				label = "VDD3V3";
+			};
+
+			channel@2 {
+				reg = <0x2>;
+				shunt-resistor-micro-ohms = <47000>;
+				label = "VDDIODDR";
+			};
+
+			channel@3 {
+				reg = <0x3>;
+				shunt-resistor-micro-ohms = <47000>;
+				label = "VDDCORE";
+			};
+
+			channel@4 {
+				reg = <0x4>;
+				shunt-resistor-micro-ohms = <47000>;
+				label = "VDDCPU";
+			};
+		};
+
+		eeprom@51 {
+			compatible = "atmel,24c02";
+			reg = <0x51>;
+			pagesize = <16>;
+			size = <256>;
+			vcc-supply = <&vdd_3v3>;
+		};
+
+		pmic@5b {
+			compatible = "microchip,mcp16502";
+			reg = <0x5b>;
+			lvin-supply = <&reg_5v>;
+			pvin1-supply = <&reg_5v>;
+			pvin2-supply = <&reg_5v>;
+			pvin3-supply = <&reg_5v>;
+			pvin4-supply = <&reg_5v>;
+
+			regulators {
+				vdd_3v3: VDD_IO {
+					regulator-name = "VDD_IO";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-initial-mode = <2>;
+					regulator-allowed-modes = <2>, <4>;
+					regulator-always-on;
+
+					regulator-state-standby {
+						regulator-on-in-suspend;
+						regulator-suspend-microvolt = <3300000>;
+						regulator-mode = <4>;
+					};
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+						regulator-mode = <4>;
+					};
+				};
+
+				vddioddr: VDD_DDR {
+					regulator-name = "VDD_DDR";
+					regulator-min-microvolt = <1350000>;
+					regulator-max-microvolt = <1350000>;
+					regulator-initial-mode = <2>;
+					regulator-allowed-modes = <2>, <4>;
+					regulator-always-on;
+
+					regulator-state-standby {
+						regulator-on-in-suspend;
+						regulator-suspend-microvolt = <1350000>;
+						regulator-mode = <4>;
+					};
+
+					regulator-state-mem {
+						regulator-on-in-suspend;
+						regulator-suspend-microvolt = <1350000>;
+						regulator-mode = <4>;
+					};
+				};
+
+				vddcore: VDD_CORE {
+					regulator-name = "VDD_CORE";
+					regulator-min-microvolt = <1150000>;
+					regulator-max-microvolt = <1150000>;
+					regulator-initial-mode = <2>;
+					regulator-allowed-modes = <2>, <4>;
+					regulator-always-on;
+
+					regulator-state-standby {
+						regulator-on-in-suspend;
+						regulator-suspend-microvolt = <1150000>;
+						regulator-mode = <4>;
+					};
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+						regulator-mode = <4>;
+					};
+				};
+
+				vddcpu: VDD_OTHER {
+					regulator-name = "VDD_OTHER";
+					regulator-min-microvolt = <1050000>;
+					regulator-max-microvolt = <1250000>;
+					regulator-initial-mode = <2>;
+					regulator-allowed-modes = <2>, <4>;
+					regulator-ramp-delay = <3125>;
+					regulator-always-on;
+
+					regulator-state-standby {
+						regulator-on-in-suspend;
+						regulator-suspend-microvolt = <1050000>;
+						regulator-mode = <4>;
+					};
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+						regulator-mode = <4>;
+					};
+				};
+
+				vldo1: LDO1 {
+					regulator-name = "LDO1";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+
+					regulator-state-standby {
+						regulator-suspend-microvolt = <1800000>;
+						regulator-on-in-suspend;
+					};
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+					};
+				};
+
+				vldo2: LDO2 {
+					regulator-name = "LDO2";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+
+					regulator-state-standby {
+						regulator-suspend-microvolt = <3300000>;
+						regulator-on-in-suspend;
+					};
+
+					regulator-state-mem {
+						regulator-off-in-suspend;
+					};
+				};
+			};
+		};
+	};
+};
+
+&main_xtal {
+	clock-frequency = <24000000>;
+};
+
+&qspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_qspi1_default>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		spi-max-frequency = <100000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		m25p,fast-read;
+		label = "at91-qspi";
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			at91bootstrap@0 {
+				label = "qspi1: at91bootstrap";
+				reg = <0x0 0x40000>;
+			};
+
+			bootloader@40000 {
+				label = "qspi1: u-boot";
+				reg = <0x40000 0x100000>;
+			};
+
+			bootloaderenv@140000 {
+				label = "qspi1: u-boot env";
+				reg = <0x140000 0x40000>;
+			};
+
+			dtb@180000 {
+				label = "qspi1: device tree";
+				reg = <0x180000 0x80000>;
+			};
+
+			kernel@200000 {
+				label = "qspi1: kernel";
+				reg = <0x200000 0x600000>;
+			};
+		};
+	};
+};
+
+&pioA {
+	pinctrl_flx3_default: flx3-default {
+		pinmux = <PIN_PD16__FLEXCOM3_IO0>,
+			 <PIN_PD17__FLEXCOM3_IO1>;
+		bias-pull-up;
+	};
+
+	pinctrl_flx10_default: flx10-default {
+		pinmux = <PIN_PC30__FLEXCOM10_IO0>,
+			 <PIN_PC31__FLEXCOM10_IO1>;
+		bias-pull-up;
+	};
+
+	pinctrl_key_gpio_default: key-gpio-default {
+		pinmux = <PIN_PD19__GPIO>;
+		bias-pull-up;
+	};
+
+	pinctrl_led_gpio_default: led-gpio-default {
+		pinmux = <PIN_PD13__GPIO>,
+			 <PIN_PD14__GPIO>,
+			 <PIN_PB15__GPIO>;
+		bias-pull-up;
+	};
+
+	pinctrl_mikrobus1_an_default: mikrobus1-an-default {
+		pinmux = <PIN_PC15__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_mikrobus2_an_default: mikrobus2-an-default {
+		pinmux = <PIN_PC13__GPIO>;
+		bias-disable;
+	};
+
+	pinctrl_nand_default: nand-default {
+		pinmux = <PIN_PD9__D0>,
+			 <PIN_PD10__D1>,
+			 <PIN_PD11__D2>,
+			 <PIN_PC21__D3>,
+			 <PIN_PC22__D4>,
+			 <PIN_PC23__D5>,
+			 <PIN_PC24__D6>,
+			 <PIN_PD2__D7>,
+			 <PIN_PD3__NANDRDY>,
+			 <PIN_PD4__NCS3_NANDCS>,
+			 <PIN_PD5__NWE_NWR0_NANDWE>,
+			 <PIN_PD6__NRD_NANDOE>,
+			 <PIN_PD7__A21_NANDALE>,
+			 <PIN_PD8__A22_NANDCLE>;
+		bias-disable;
+		slew-rate = <0>;
+	};
+
+	pinctrl_qspi1_default: qspi1-default {
+		pinmux = <PIN_PB22__QSPI1_IO3>,
+			 <PIN_PB23__QSPI1_IO2>,
+			 <PIN_PB24__QSPI1_IO1>,
+			 <PIN_PB25__QSPI1_IO0>,
+			 <PIN_PB26__QSPI1_CS>,
+			 <PIN_PB27__QSPI1_SCK>;
+		bias-pull-up;
+		slew-rate = <0>;
+	};
+
+	pinctrl_sdmmc0_default: sdmmc0-default {
+		pinmux = <PIN_PA0__SDMMC0_CK>,
+			 <PIN_PA1__SDMMC0_CMD>,
+			 <PIN_PA2__SDMMC0_RSTN>,
+			 <PIN_PA3__SDMMC0_DAT0>,
+			 <PIN_PA4__SDMMC0_DAT1>,
+			 <PIN_PA5__SDMMC0_DAT2>,
+			 <PIN_PA6__SDMMC0_DAT3>;
+		bias-pull-up;
+		slew-rate = <0>;
+	};
+
+	pinctrl_sdmmc1_default: sdmmc1-default {
+		pinmux = <PIN_PB29__SDMMC1_CMD>,
+			 <PIN_PB30__SDMMC1_CK>,
+			 <PIN_PB31__SDMMC1_DAT0>,
+			 <PIN_PC0__SDMMC1_DAT1>,
+			 <PIN_PC1__SDMMC1_DAT2>,
+			 <PIN_PC2__SDMMC1_DAT3>,
+			 <PIN_PC4__SDMMC1_CD>;
+		bias-pull-up;
+		slew-rate = <0>;
+	};
+};
+
+&rtt {
+	atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
+};
+
+/* M.2 slot for wireless card */
+&sdmmc0 {
+	bus-width = <4>;
+	cd-gpios = <&pioA 31 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	sdhci-caps-mask = <0x0 0x00200000>;
+	vmmc-supply = <&vdd_3v3>;
+	vqmmc-supply = <&vdd_3v3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdmmc0_default>;
+	status = "okay";
+};
+
+/* micro SD socket */
+&sdmmc1 {
+	bus-width = <4>;
+	disable-wp;
+	sdhci-caps-mask = <0x0 0x00200000>;
+	vmmc-supply = <&vdd_3v3>;
+	vqmmc-supply = <&vdd_3v3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdmmc1_default>;
+	status = "okay";
+};
+
+&slow_xtal {
+	clock-frequency = <32768>;
+};
+
+&shdwc {
+	debounce-delay-us = <976>;
+	status = "okay";
+
+	input@0 {
+		reg = <0>;
+	};
+};
+
+&tcb0 {
+	timer0: timer@0 {
+		compatible = "atmel,tcb-timer";
+		reg = <0>;
+	};
+
+	timer1: timer@1 {
+		compatible = "atmel,tcb-timer";
+		reg = <1>;
+	};
+};
+
+&trng {
+	status = "okay";
+};
+
+&vddout25 {
+	vin-supply = <&vdd_3v3>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/at91-sama7g5ek.dts b/arch/arm/boot/dts/microchip/at91-sama7g5ek.dts
index 08685a10eda1..3924f62ff0fb 100644
--- a/arch/arm/boot/dts/at91-sama7g5ek.dts
+++ b/arch/arm/boot/dts/microchip/at91-sama7g5ek.dts
@@ -14,6 +14,7 @@
 #include <dt-bindings/mfd/atmel-flexcom.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/pinctrl/at91.h>
+#include <dt-bindings/sound/microchip,pdmc.h>
 
 / {
 	model = "Microchip SAMA7G5-EK";
@@ -34,23 +35,13 @@
 		i2c2 = &i2c9;
 	};
 
-	clocks {
-		slow_xtal {
-			clock-frequency = <32768>;
-		};
-
-		main_xtal {
-			clock-frequency = <24000000>;
-		};
-	};
-
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_key_gpio_default>;
 
-		bp1 {
+		button {
 			label = "PB_USER";
 			gpios = <&pioA PIN_PA12 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_PROG1>;
@@ -87,6 +78,14 @@
 		reg = <0x60000000 0x20000000>;
 	};
 
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5V_MAIN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
 	sound: sound {
 		compatible = "simple-audio-card";
 		simple-audio-card,name = "sama7g5ek audio";
@@ -128,6 +127,7 @@
 	vref-supply = <&vddout25>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_mikrobus1_an_default &pinctrl_mikrobus2_an_default>;
+	atmel,trigger-edge-type = <IRQ_TYPE_EDGE_RISING>;
 	status = "okay";
 };
 
@@ -235,16 +235,52 @@
 		i2c-digital-filter-width-ns = <35>;
 		status = "okay";
 
-		mcp16502@5b {
+		power-monitor@10 {
+			compatible = "microchip,pac1934";
+			reg = <0x10>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@1 {
+				reg = <0x1>;
+				shunt-resistor-micro-ohms = <10000>;
+				label = "VDD3V3";
+			};
+
+			channel@2 {
+				reg = <0x2>;
+				shunt-resistor-micro-ohms = <10000>;
+				label = "VDDIODDR";
+			};
+
+			channel@3 {
+				reg = <0x3>;
+				shunt-resistor-micro-ohms = <10000>;
+				label = "VDDCORE";
+			};
+
+			channel@4 {
+				reg = <0x4>;
+				shunt-resistor-micro-ohms = <10000>;
+				label = "VDDCPU";
+			};
+		};
+
+		pmic@5b {
 			compatible = "microchip,mcp16502";
 			reg = <0x5b>;
+			lvin-supply = <&reg_5v>;
+			pvin1-supply = <&reg_5v>;
+			pvin2-supply = <&reg_5v>;
+			pvin3-supply = <&reg_5v>;
+			pvin4-supply = <&reg_5v>;
 			status = "okay";
 
 			regulators {
 				vdd_3v3: VDD_IO {
 					regulator-name = "VDD_IO";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <3700000>;
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
 					regulator-initial-mode = <2>;
 					regulator-allowed-modes = <2>, <4>;
 					regulator-always-on;
@@ -263,8 +299,8 @@
 
 				vddioddr: VDD_DDR {
 					regulator-name = "VDD_DDR";
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1450000>;
+					regulator-min-microvolt = <1350000>;
+					regulator-max-microvolt = <1350000>;
 					regulator-initial-mode = <2>;
 					regulator-allowed-modes = <2>, <4>;
 					regulator-always-on;
@@ -284,15 +320,15 @@
 
 				vddcore: VDD_CORE {
 					regulator-name = "VDD_CORE";
-					regulator-min-microvolt = <1100000>;
-					regulator-max-microvolt = <1850000>;
+					regulator-min-microvolt = <1150000>;
+					regulator-max-microvolt = <1150000>;
 					regulator-initial-mode = <2>;
 					regulator-allowed-modes = <2>, <4>;
 					regulator-always-on;
 
 					regulator-state-standby {
 						regulator-on-in-suspend;
-						regulator-suspend-voltage = <1150000>;
+						regulator-suspend-microvolt = <1150000>;
 						regulator-mode = <4>;
 					};
 
@@ -305,7 +341,7 @@
 				vddcpu: VDD_OTHER {
 					regulator-name = "VDD_OTHER";
 					regulator-min-microvolt = <1050000>;
-					regulator-max-microvolt = <1850000>;
+					regulator-max-microvolt = <1250000>;
 					regulator-initial-mode = <2>;
 					regulator-allowed-modes = <2>, <4>;
 					regulator-ramp-delay = <3125>;
@@ -313,7 +349,7 @@
 
 					regulator-state-standby {
 						regulator-on-in-suspend;
-						regulator-suspend-voltage = <1050000>;
+						regulator-suspend-microvolt = <1050000>;
 						regulator-mode = <4>;
 					};
 
@@ -325,12 +361,12 @@
 
 				vldo1: LDO1 {
 					regulator-name = "LDO1";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <3700000>;
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
 					regulator-always-on;
 
 					regulator-state-standby {
-						regulator-suspend-voltage = <1800000>;
+						regulator-suspend-microvolt = <1800000>;
 						regulator-on-in-suspend;
 					};
 
@@ -345,7 +381,7 @@
 					regulator-max-microvolt = <3700000>;
 
 					regulator-state-standby {
-						regulator-suspend-voltage = <1800000>;
+						regulator-suspend-microvolt = <1800000>;
 						regulator-on-in-suspend;
 					};
 
@@ -402,6 +438,42 @@
 		i2c-digital-filter;
 		i2c-digital-filter-width-ns = <35>;
 		status = "okay";
+
+		eeprom0: eeprom@52 {
+			compatible = "microchip,24aa025e48";
+			reg = <0x52>;
+			size = <256>;
+			pagesize = <16>;
+			vcc-supply = <&vdd_3v3>;
+
+			nvmem-layout {
+				compatible = "fixed-layout";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				eeprom0_eui48: eui48@fa {
+					reg = <0xfa 0x6>;
+				};
+			};
+		};
+
+		eeprom1: eeprom@53 {
+			compatible = "microchip,24aa025e48";
+			reg = <0x53>;
+			size = <256>;
+			pagesize = <16>;
+			vcc-supply = <&vdd_3v3>;
+
+			nvmem-layout {
+				compatible = "fixed-layout";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				eeprom1_eui48: eui48@fa {
+					reg = <0xfa 0x6>;
+				};
+			};
+		};
 	};
 };
 
@@ -439,6 +511,8 @@
 		     &pinctrl_gmac0_txck_default
 		     &pinctrl_gmac0_phy_irq>;
 	phy-mode = "rgmii-id";
+	nvmem-cells = <&eeprom0_eui48>;
+	nvmem-cell-names = "mac-address";
 	status = "okay";
 
 	ethernet-phy@7 {
@@ -456,7 +530,9 @@
 		     &pinctrl_gmac1_mdio_default
 		     &pinctrl_gmac1_phy_irq>;
 	phy-mode = "rmii";
-	status = "okay";
+	nvmem-cells = <&eeprom1_eui48>;
+	nvmem-cell-names = "mac-address";
+	status = "okay"; /* Conflict with pdmc0. */
 
 	ethernet-phy@0 {
 		reg = <0x0>;
@@ -470,6 +546,21 @@
 	pinctrl-0 = <&pinctrl_i2s0_default>;
 };
 
+&main_xtal {
+	clock-frequency = <24000000>;
+};
+
+&pdmc0 {
+	#sound-dai-cells = <0>;
+	microchip,mic-pos = <MCHP_PDMC_DS0 MCHP_PDMC_CLK_NEGATIVE>, /* MIC 1 */
+			    <MCHP_PDMC_DS1 MCHP_PDMC_CLK_NEGATIVE>, /* MIC 2 */
+			    <MCHP_PDMC_DS0 MCHP_PDMC_CLK_POSITIVE>, /* MIC 3 */
+			    <MCHP_PDMC_DS1 MCHP_PDMC_CLK_POSITIVE>; /* MIC 4 */
+	status = "disabled"; /* Conflict with gmac1. */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pdmc0_default>;
+};
+
 &pioA {
 
 	pinctrl_can0_default: can0_default {
@@ -495,7 +586,7 @@
 	pinctrl_flx3_default: flx3_default {
 		pinmux = <PIN_PD16__FLEXCOM3_IO0>,
 			 <PIN_PD17__FLEXCOM3_IO1>;
-		bias-disable;
+		bias-pull-up;
 	};
 
 	pinctrl_flx4_default: flx4_default {
@@ -639,6 +730,13 @@
 		bias-disable;
 	};
 
+	pinctrl_pdmc0_default: pdmc0_default {
+		pinmux = <PIN_PD23__PDMC0_DS0>,
+			 <PIN_PD24__PDMC0_DS1>,
+			 <PIN_PD22__PDMC0_CLK>;
+		bias_disable;
+	};
+
 	pinctrl_qspi: qspi {
 		pinmux = <PIN_PB12__QSPI0_IO0>,
 			 <PIN_PB11__QSPI0_IO1>,
@@ -655,7 +753,7 @@
 			 <PIN_PB21__QSPI0_INT>;
 		bias-disable;
 		slew-rate = <0>;
-		atmel,drive-strength = <ATMEL_PIO_DRVSTR_HI>;
+		atmel,drive-strength = <ATMEL_PIO_DRVSTR_ME>;
 	};
 
 	pinctrl_sdmmc0_default: sdmmc0_default {
@@ -745,8 +843,9 @@
 &sdmmc0 {
 	bus-width = <8>;
 	non-removable;
-	no-1-8-v;
 	sdhci-caps-mask = <0x0 0x00200000>;
+	vmmc-supply = <&vdd_3v3>;
+	vqmmc-supply = <&vldo1>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_sdmmc0_default>;
 	status = "okay";
@@ -756,6 +855,8 @@
 	bus-width = <4>;
 	no-1-8-v;
 	sdhci-caps-mask = <0x0 0x00200000>;
+	vmmc-supply = <&vdd_3v3>;
+	vqmmc-supply = <&vdd_3v3>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_sdmmc1_default>;
 	status = "okay";
@@ -770,7 +871,7 @@
 };
 
 &shdwc {
-	atmel,shdwc-debouncer = <976>;
+	debounce-delay-us = <976>;
 	status = "okay";
 
 	input@0 {
@@ -778,6 +879,10 @@
 	};
 };
 
+&slow_xtal {
+	clock-frequency = <32768>;
+};
+
 &spdifrx {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_spdifrx_default>;
diff --git a/arch/arm/boot/dts/at91-smartkiz.dts b/arch/arm/boot/dts/microchip/at91-smartkiz.dts
index b76a6b5ac464..b76a6b5ac464 100644
--- a/arch/arm/boot/dts/at91-smartkiz.dts
+++ b/arch/arm/boot/dts/microchip/at91-smartkiz.dts
diff --git a/arch/arm/boot/dts/at91-som60.dtsi b/arch/arm/boot/dts/microchip/at91-som60.dtsi
index 39474a112b16..39474a112b16 100644
--- a/arch/arm/boot/dts/at91-som60.dtsi
+++ b/arch/arm/boot/dts/microchip/at91-som60.dtsi
diff --git a/arch/arm/boot/dts/at91-tse850-3.dts b/arch/arm/boot/dts/microchip/at91-tse850-3.dts
index 7e5c598e7e68..9d58a3931207 100644
--- a/arch/arm/boot/dts/at91-tse850-3.dts
+++ b/arch/arm/boot/dts/microchip/at91-tse850-3.dts
@@ -106,35 +106,35 @@
 	leds {
 		compatible = "gpio-leds";
 
-		ch1-red {
+		led-ch1-red {
 			label = "ch-1:red";
 			gpios = <&pioA 23 GPIO_ACTIVE_LOW>;
 		};
-		ch1-green {
+		led-ch1-green {
 			label = "ch-1:green";
 			gpios = <&pioA 22 GPIO_ACTIVE_LOW>;
 		};
-		ch2-red {
+		led-ch2-red {
 			label = "ch-2:red";
 			gpios = <&pioA 21 GPIO_ACTIVE_LOW>;
 		};
-		ch2-green {
+		led-ch2-green {
 			label = "ch-2:green";
 			gpios = <&pioA 20 GPIO_ACTIVE_LOW>;
 		};
-		data-red {
+		led-data-red {
 			label = "data:red";
 			gpios = <&pioA 19 GPIO_ACTIVE_LOW>;
 		};
-		data-green {
+		led-data-green {
 			label = "data:green";
 			gpios = <&pioA 18 GPIO_ACTIVE_LOW>;
 		};
-		alarm-red {
+		led-alarm-red {
 			label = "alarm:red";
 			gpios = <&pioA 17 GPIO_ACTIVE_LOW>;
 		};
-		alarm-green {
+		led-alarm-green {
 			label = "alarm:green";
 			gpios = <&pioA 16 GPIO_ACTIVE_LOW>;
 		};
@@ -300,3 +300,63 @@
 
 	dmas = <0>, <0>;	/*  Do not use DMA for dbgu */
 };
+
+&pioA {
+	gpio-line-names =
+	/*  0 */	"SUP-A", "SUP-B", "SUP-C", "SIG<LEV",
+	/*  4 */	"", "/RFRST", "", "",
+	/*  8 */	"/ADD", "", "/LOOP1", "/LOOP2",
+	/* 12 */	"", "", "", "",
+	/* 16 */	"LED1GREEN", "LED1RED", "LED2GREEN", "LED2RED",
+	/* 20 */	"LED3GREEN", "LED3RED", "LED4GREEN", "LED4RED",
+	/* 24 */	"", "", "", "",
+	/* 28 */	"", "", "SDA", "SCL";
+};
+
+&pioB {
+	gpio-line-names =
+	/*  0 */	"", "", "", "",
+	/*  4 */	"", "", "", "",
+	/*  8 */	"", "", "", "",
+	/* 12 */	"", "", "", "",
+	/* 16 */	"", "", "", "",
+	/* 20 */	"", "", "", "",
+	/* 24 */	"", "", "SIG<LIN", "SIG>LIN",
+	/* 28 */	"RXD", "TXD", "BRX", "BTX";
+};
+
+&pioC {
+	gpio-line-names =
+	/*  0 */	"ETX0", "ETX1", "ERX0", "ERX1",
+	/*  4 */	"ETXEN", "ECRSDV", "ERXER", "EREFCK",
+	/*  8 */	"EMDC", "EMDIO", "", "",
+	/* 12 */	"", "", "", "/ILIM",
+	/* 16 */	"BCK", "LRCK", "DIN", "",
+	/* 20 */	"", "", "", "",
+	/* 24 */	"", "", "", "",
+	/* 28 */	"", "", "", "VBUS";
+};
+
+&pioD {
+	gpio-line-names =
+	/*  0 */	"I1", "I2", "O1", "EXTVEN",
+	/*  4 */	"", "456KHZ", "VCTRL", "SYNCSEL",
+	/*  8 */	"STEREO", "", "", "",
+	/* 12 */	"", "", "", "",
+	/* 16 */	"", ">LIN", "LIN>", "",
+	/* 20 */	"VREFEN", "", "", "",
+	/* 24 */	"", "", "VINOK", "",
+	/* 28 */	"POEOK", "USBON", "POELOAD", "";
+};
+
+&pioE {
+	gpio-line-names =
+	/*  0 */	"", "", "", "",
+	/*  4 */	"", "", "", "",
+	/*  8 */	"", "", "", "",
+	/* 12 */	"", "", "", "",
+	/* 16 */	"", "", "", "",
+	/* 20 */	"", "ALE", "CLE", "",
+	/* 24 */	"", "", "", "",
+	/* 28 */	"", "", "", "/ETHINT";
+};
diff --git a/arch/arm/boot/dts/at91-vinco.dts b/arch/arm/boot/dts/microchip/at91-vinco.dts
index a51a3372afa1..c5fc51667066 100644
--- a/arch/arm/boot/dts/at91-vinco.dts
+++ b/arch/arm/boot/dts/microchip/at91-vinco.dts
@@ -59,7 +59,7 @@
 			spi0: spi@f8010000 {
 				cs-gpios = <&pioC 3 0>, <0>, <0>, <0>;
 				status = "okay";
-				m25p80@0 {
+				flash@0 {
 					compatible = "n25q32b", "jedec,spi-nor";
 					spi-max-frequency = <50000000>;
 					reg = <0>;
@@ -159,19 +159,19 @@
 			atmel,vbus-gpio = <&pioE 31 GPIO_ACTIVE_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usba_vbus>;
-			status = "disable";
+			status = "disabled";
 		};
 
-		usb1: ohci@500000 {
+		usb1: usb@500000 {
 			num-ports = <3>;
 			atmel,vbus-gpio = <0
 					   &pioE 11 GPIO_ACTIVE_LOW
 					   &pioE 12 GPIO_ACTIVE_LOW
 					  >;
-			status = "disable";
+			status = "disabled";
 		};
 
-		usb2: ehci@600000 {
+		usb2: usb@600000 {
 			/* 4G Modem */
 			status = "okay";
 		};
diff --git a/arch/arm/boot/dts/at91-wb45n.dts b/arch/arm/boot/dts/microchip/at91-wb45n.dts
index 54d130c92185..ef73f727f7bd 100644
--- a/arch/arm/boot/dts/at91-wb45n.dts
+++ b/arch/arm/boot/dts/microchip/at91-wb45n.dts
@@ -12,13 +12,10 @@
 	model = "Laird Workgroup Bridge 45N - Atmel AT91SAM (dt)";
 	compatible = "laird,wb45n", "laird,wbxx", "atmel,at91sam9x5", "atmel,at91sam9";
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		irqbtn@18 {
-			reg = <18>;
+		button {
 			label = "IRQBTN";
 			linux,code = <99>;
 			gpios = <&pioB 18 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/at91-wb45n.dtsi b/arch/arm/boot/dts/microchip/at91-wb45n.dtsi
index 430c75358086..430c75358086 100644
--- a/arch/arm/boot/dts/at91-wb45n.dtsi
+++ b/arch/arm/boot/dts/microchip/at91-wb45n.dtsi
diff --git a/arch/arm/boot/dts/at91-wb50n.dts b/arch/arm/boot/dts/microchip/at91-wb50n.dts
index 89f0f717f7ed..ec2becf6133b 100644
--- a/arch/arm/boot/dts/at91-wb50n.dts
+++ b/arch/arm/boot/dts/microchip/at91-wb50n.dts
@@ -13,21 +13,17 @@
 	model = "Laird Workgroup Bridge 50N - Atmel SAMA5D";
 	compatible = "laird,wb50n", "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		btn0@10 {
-			reg = <10>;
+		button-0 {
 			label = "BTNESC";
 			linux,code = <1>; /* ESC button */
 			gpios = <&pioA 10 GPIO_ACTIVE_LOW>;
 			wakeup-source;
 		};
 
-		irqbtn@31 {
-			reg = <31>;
+		button-1 {
 			label = "IRQBTN";
 			linux,code = <99>; /* SysReq button */
 			gpios = <&pioE 31 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/at91-wb50n.dtsi b/arch/arm/boot/dts/microchip/at91-wb50n.dtsi
index 74b249bb6351..74b249bb6351 100644
--- a/arch/arm/boot/dts/at91-wb50n.dtsi
+++ b/arch/arm/boot/dts/microchip/at91-wb50n.dtsi
diff --git a/arch/arm/boot/dts/at91rm9200.dtsi b/arch/arm/boot/dts/microchip/at91rm9200.dtsi
index d1181ead18e5..e105ad855ce8 100644
--- a/arch/arm/boot/dts/at91rm9200.dtsi
+++ b/arch/arm/boot/dts/microchip/at91rm9200.dtsi
@@ -13,6 +13,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	#address-cells = <1>;
@@ -101,7 +102,7 @@
 				reg = <0xffffff00 0x100>;
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,at91rm9200-pmc", "syscon";
 				reg = <0xfffffc00 0x100>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -134,9 +135,9 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				reg = <0xfffa0000 0x100>;
-				interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0
-					      18 IRQ_TYPE_LEVEL_HIGH 0
-					      19 IRQ_TYPE_LEVEL_HIGH 0>;
+				interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>,
+					     <18 IRQ_TYPE_LEVEL_HIGH 0>,
+					     <19 IRQ_TYPE_LEVEL_HIGH 0>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 17>, <&pmc PMC_TYPE_PERIPHERAL 18>, <&pmc PMC_TYPE_PERIPHERAL 19>, <&slow_xtal>;
 				clock-names = "t0_clk", "t1_clk", "t2_clk", "slow_clk";
 			};
@@ -146,9 +147,9 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				reg = <0xfffa4000 0x100>;
-				interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0
-					      21 IRQ_TYPE_LEVEL_HIGH 0
-					      22 IRQ_TYPE_LEVEL_HIGH 0>;
+				interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>,
+					     <21 IRQ_TYPE_LEVEL_HIGH 0>,
+					     <22 IRQ_TYPE_LEVEL_HIGH 0>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 20>, <&pmc PMC_TYPE_PERIPHERAL 21>, <&pmc PMC_TYPE_PERIPHERAL 22>, <&slow_xtal>;
 				clock-names = "t0_clk", "t1_clk", "t2_clk", "slow_clk";
 			};
@@ -224,7 +225,7 @@
 			pinctrl@fffff400 {
 				#address-cells = <1>;
 				#size-cells = <1>;
-				compatible = "atmel,at91rm9200-pinctrl", "simple-bus";
+				compatible = "atmel,at91rm9200-pinctrl", "simple-mfd";
 				ranges = <0xfffff400 0xfffff400 0x800>;
 
 				atmel,mux-mask = <
@@ -596,6 +597,7 @@
 			dbgu: serial@fffff200 {
 				compatible = "atmel,at91rm9200-dbgu", "atmel,at91rm9200-usart";
 				reg = <0xfffff200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
@@ -607,6 +609,7 @@
 			usart0: serial@fffc0000 {
 				compatible = "atmel,at91rm9200-usart";
 				reg = <0xfffc0000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -620,6 +623,7 @@
 			usart1: serial@fffc4000 {
 				compatible = "atmel,at91rm9200-usart";
 				reg = <0xfffc4000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -633,6 +637,7 @@
 			usart2: serial@fffc8000 {
 				compatible = "atmel,at91rm9200-usart";
 				reg = <0xfffc8000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -646,6 +651,7 @@
 			usart3: serial@fffcc000 {
 				compatible = "atmel,at91rm9200-usart";
 				reg = <0xfffcc000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <23 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -660,7 +666,7 @@
 				compatible = "atmel,at91rm9200-udc";
 				reg = <0xfffb0000 0x4000>;
 				interrupts = <11 IRQ_TYPE_LEVEL_HIGH 2>;
-				clocks = <&pmc PMC_TYPE_PERIPHERAL 11>, <&pmc PMC_TYPE_SYSTEM 2>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 11>, <&pmc PMC_TYPE_SYSTEM 1>;
 				clock-names = "pclk", "hclk";
 				status = "disabled";
 			};
@@ -696,7 +702,7 @@
 			status = "disabled";
 		};
 
-		usb0: ohci@300000 {
+		usb0: usb@300000 {
 			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
 			reg = <0x00300000 0x100000>;
 			interrupts = <23 IRQ_TYPE_LEVEL_HIGH 2>;
@@ -708,9 +714,8 @@
 
 	i2c-gpio-0 {
 		compatible = "i2c-gpio";
-		gpios = <&pioA 25 GPIO_ACTIVE_HIGH /* sda */
-			 &pioA 26 GPIO_ACTIVE_HIGH /* scl */
-			>;
+		sda-gpios = <&pioA 25 GPIO_ACTIVE_HIGH>;
+		scl-gpios = <&pioA 26 GPIO_ACTIVE_HIGH>;
 		i2c-gpio,sda-open-drain;
 		i2c-gpio,scl-open-drain;
 		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
diff --git a/arch/arm/boot/dts/at91rm9200_pqfp.dtsi b/arch/arm/boot/dts/microchip/at91rm9200_pqfp.dtsi
index c3d4177b9823..c3d4177b9823 100644
--- a/arch/arm/boot/dts/at91rm9200_pqfp.dtsi
+++ b/arch/arm/boot/dts/microchip/at91rm9200_pqfp.dtsi
diff --git a/arch/arm/boot/dts/at91rm9200ek.dts b/arch/arm/boot/dts/microchip/at91rm9200ek.dts
index e1ef4e44e663..ce691c4692b9 100644
--- a/arch/arm/boot/dts/at91rm9200ek.dts
+++ b/arch/arm/boot/dts/microchip/at91rm9200ek.dts
@@ -73,7 +73,7 @@
 			spi0: spi@fffe0000 {
 				status = "okay";
 				cs-gpios = <&pioA 3 0>, <0>, <0>, <0>;
-				mtd_dataflash@0 {
+				flash@0 {
 					compatible = "atmel,at45", "atmel,dataflash";
 					spi-max-frequency = <15000000>;
 					reg = <0>;
@@ -89,12 +89,12 @@
 			};
 		};
 
-		usb0: ohci@300000 {
+		usb0: usb@300000 {
 			num-ports = <2>;
 			status = "okay";
 		};
 
-		nor_flash@10000000 {
+		flash@10000000 {
 			compatible = "cfi-flash";
 			reg = <0x10000000 0x800000>;
 			linux,mtd-name = "physmap-flash.0";
@@ -127,19 +127,19 @@
 	leds {
 		compatible = "gpio-leds";
 
-		ds2 {
+		led-ds2 {
 			label = "green";
 			gpios = <&pioB 0 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "mmc0";
 		};
 
-		ds4 {
+		led-ds4 {
 			label = "yellow";
 			gpios = <&pioB 1 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "heartbeat";
 		};
 
-		ds6 {
+		led-ds6 {
 			label = "red";
 			gpios = <&pioB 2 GPIO_ACTIVE_LOW>;
 		};
diff --git a/arch/arm/boot/dts/at91sam9260.dtsi b/arch/arm/boot/dts/microchip/at91sam9260.dtsi
index 7368347c9357..fc0b6a73204f 100644
--- a/arch/arm/boot/dts/at91sam9260.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9260.dtsi
@@ -11,6 +11,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	#address-cells = <1>;
@@ -64,7 +65,7 @@
 			clock-frequency = <0>;
 		};
 
-		adc_op_clk: adc_op_clk{
+		adc_op_clk: adc_op_clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <5000000>;
@@ -114,7 +115,7 @@
 				reg = <0xffffee00 0x200>;
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,at91sam9260-pmc", "syscon";
 				reg = <0xfffffc00 0x100>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -123,13 +124,13 @@
 				clock-names = "slow_xtal", "main_xtal";
 			};
 
-			rstc@fffffd00 {
+			reset-controller@fffffd00 {
 				compatible = "atmel,at91sam9260-rstc";
 				reg = <0xfffffd00 0x10>;
 				clocks = <&pmc PMC_TYPE_CORE PMC_SLOW>;
 			};
 
-			shdwc@fffffd10 {
+			shdwc: poweroff@fffffd10 {
 				compatible = "atmel,at91sam9260-shdwc";
 				reg = <0xfffffd10 0x10>;
 				clocks = <&pmc PMC_TYPE_CORE PMC_SLOW>;
@@ -147,9 +148,9 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				reg = <0xfffa0000 0x100>;
-				interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0
-					      18 IRQ_TYPE_LEVEL_HIGH 0
-					      19 IRQ_TYPE_LEVEL_HIGH 0>;
+				interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>,
+					     <18 IRQ_TYPE_LEVEL_HIGH 0>,
+					     <19 IRQ_TYPE_LEVEL_HIGH 0>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 17>, <&pmc PMC_TYPE_PERIPHERAL 18>, <&pmc PMC_TYPE_PERIPHERAL 19>, <&pmc PMC_TYPE_CORE PMC_SLOW>;
 				clock-names = "t0_clk", "t1_clk", "t2_clk", "slow_clk";
 			};
@@ -159,9 +160,9 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				reg = <0xfffdc000 0x100>;
-				interrupts = <26 IRQ_TYPE_LEVEL_HIGH 0
-					      27 IRQ_TYPE_LEVEL_HIGH 0
-					      28 IRQ_TYPE_LEVEL_HIGH 0>;
+				interrupts = <26 IRQ_TYPE_LEVEL_HIGH 0>,
+					     <27 IRQ_TYPE_LEVEL_HIGH 0>,
+					     <28 IRQ_TYPE_LEVEL_HIGH 0>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 26>, <&pmc PMC_TYPE_PERIPHERAL 27>, <&pmc PMC_TYPE_PERIPHERAL 28>, <&pmc PMC_TYPE_CORE PMC_SLOW>;
 				clock-names = "t0_clk", "t1_clk", "t2_clk", "slow_clk";
 			};
@@ -169,7 +170,7 @@
 			pinctrl: pinctrl@fffff400 {
 				#address-cells = <1>;
 				#size-cells = <1>;
-				compatible = "atmel,at91rm9200-pinctrl", "simple-bus";
+				compatible = "atmel,at91rm9200-pinctrl", "simple-mfd";
 				ranges = <0xfffff400 0xfffff400 0x600>;
 
 				atmel,mux-mask = <
@@ -532,6 +533,7 @@
 			dbgu: serial@fffff200 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xfffff200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
@@ -543,6 +545,7 @@
 			usart0: serial@fffb0000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffb0000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -556,6 +559,7 @@
 			usart1: serial@fffb4000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffb4000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -569,6 +573,7 @@
 			usart2: serial@fffb8000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffb8000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -582,6 +587,7 @@
 			usart3: serial@fffd0000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffd0000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <23 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -595,6 +601,7 @@
 			uart0: serial@fffd4000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffd4000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <24 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -608,6 +615,7 @@
 			uart1: serial@fffd8000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffd8000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <25 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -734,7 +742,7 @@
 			};
 		};
 
-		usb0: ohci@500000 {
+		usb0: usb@500000 {
 			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
 			reg = <0x00500000 0x100000>;
 			interrupts = <20 IRQ_TYPE_LEVEL_HIGH 2>;
@@ -773,9 +781,8 @@
 
 	i2c_gpio0: i2c-gpio-0 {
 		compatible = "i2c-gpio";
-		gpios = <&pioA 23 GPIO_ACTIVE_HIGH /* sda */
-			 &pioA 24 GPIO_ACTIVE_HIGH /* scl */
-			>;
+		sda-gpios = <&pioA 23 GPIO_ACTIVE_HIGH>;
+		scl-gpios = <&pioA 24 GPIO_ACTIVE_HIGH>;
 		i2c-gpio,sda-open-drain;
 		i2c-gpio,scl-open-drain;
 		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
diff --git a/arch/arm/boot/dts/at91sam9260ek.dts b/arch/arm/boot/dts/microchip/at91sam9260ek.dts
index ce96345d28a3..8522a210b484 100644
--- a/arch/arm/boot/dts/at91sam9260ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9260ek.dts
@@ -92,7 +92,7 @@
 
 			spi0: spi@fffc8000 {
 				cs-gpios = <0>, <&pioC 11 0>, <0>, <0>;
-				mtd_dataflash@1 {
+				flash@1 {
 					compatible = "atmel,at45", "atmel,dataflash";
 					spi-max-frequency = <50000000>;
 					reg = <1>;
@@ -112,7 +112,7 @@
 				};
 			};
 
-			shdwc@fffffd10 {
+			shdwc: poweroff@fffffd10 {
 				atmel,wakeup-counter = <10>;
 				atmel,wakeup-rtt-timer;
 			};
@@ -131,7 +131,7 @@
 			};
 		};
 
-		usb0: ohci@500000 {
+		usb0: usb@500000 {
 			num-ports = <2>;
 			status = "okay";
 		};
@@ -144,17 +144,17 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		btn3 {
+		button-3 {
 			label = "Button 3";
 			gpios = <&pioA 30 GPIO_ACTIVE_LOW>;
 			linux,code = <0x103>;
 			wakeup-source;
 		};
 
-		btn4 {
+		button-4 {
 			label = "Button 4";
 			gpios = <&pioA 31 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_PROG1>;
@@ -165,7 +165,7 @@
 	i2c-gpio-0 {
 		status = "okay";
 
-		24c512@50 {
+		eeprom@50 {
 			compatible = "atmel,24c512";
 			reg = <0x50>;
 		};
@@ -174,13 +174,13 @@
 	leds {
 		compatible = "gpio-leds";
 
-		ds1 {
+		led-ds1 {
 			label = "ds1";
 			gpios = <&pioA 9 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 
-		ds5 {
+		led-ds5 {
 			label = "ds5";
 			gpios = <&pioA 6 GPIO_ACTIVE_LOW>;
 		};
diff --git a/arch/arm/boot/dts/at91sam9261.dtsi b/arch/arm/boot/dts/microchip/at91sam9261.dtsi
index 7adc36ca8a46..d1d678b77e84 100644
--- a/arch/arm/boot/dts/at91sam9261.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9261.dtsi
@@ -9,6 +9,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	#address-cells = <1>;
@@ -76,7 +77,7 @@
 		#size-cells = <1>;
 		ranges;
 
-		usb0: ohci@500000 {
+		usb0: usb@500000 {
 			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
 			reg = <0x00500000 0x100000>;
 			interrupts = <20 IRQ_TYPE_LEVEL_HIGH 2>;
@@ -179,6 +180,7 @@
 			usart0: serial@fffb0000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffb0000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -192,6 +194,7 @@
 			usart1: serial@fffb4000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffb4000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -202,9 +205,10 @@
 				status = "disabled";
 			};
 
-			usart2: serial@fffb8000{
+			usart2: serial@fffb8000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffb8000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -301,6 +305,7 @@
 			dbgu: serial@fffff200 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xfffff200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
@@ -312,7 +317,7 @@
 			pinctrl@fffff400 {
 				#address-cells = <1>;
 				#size-cells = <1>;
-				compatible = "atmel,at91rm9200-pinctrl", "simple-bus";
+				compatible = "atmel,at91rm9200-pinctrl", "simple-mfd";
 				ranges = <0xfffff400 0xfffff400 0x600>;
 
 				atmel,mux-mask =
@@ -594,7 +599,7 @@
 				};
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,at91sam9261-pmc", "syscon";
 				reg = <0xfffffc00 0x100>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -603,13 +608,13 @@
 				clock-names = "slow_xtal", "main_xtal";
 			};
 
-			rstc@fffffd00 {
+			reset-controller@fffffd00 {
 				compatible = "atmel,at91sam9260-rstc";
 				reg = <0xfffffd00 0x10>;
 				clocks = <&slow_xtal>;
 			};
 
-			shdwc@fffffd10 {
+			poweroff@fffffd10 {
 				compatible = "atmel,at91sam9260-shdwc";
 				reg = <0xfffffd10 0x10>;
 				clocks = <&slow_xtal>;
@@ -650,8 +655,8 @@
 		compatible = "i2c-gpio";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_i2c_bitbang>;
-		gpios = <&pioA 7 GPIO_ACTIVE_HIGH>, /* sda */
-			<&pioA 8 GPIO_ACTIVE_HIGH>; /* scl */
+		sda-gpios = <&pioA 7 GPIO_ACTIVE_HIGH>;
+		scl-gpios = <&pioA 8 GPIO_ACTIVE_HIGH>;
 		i2c-gpio,sda-open-drain;
 		i2c-gpio,scl-open-drain;
 		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
diff --git a/arch/arm/boot/dts/at91sam9261ek.dts b/arch/arm/boot/dts/microchip/at91sam9261ek.dts
index beed819609e8..313bc2797fde 100644
--- a/arch/arm/boot/dts/at91sam9261ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9261ek.dts
@@ -31,7 +31,7 @@
 	};
 
 	ahb {
-		usb0: ohci@500000 {
+		usb0: usb@500000 {
 			status = "okay";
 		};
 
@@ -145,7 +145,7 @@
 				cs-gpios = <&pioA 3 0>, <0>, <&pioA 28 0>, <0>;
 				status = "okay";
 
-				mtd_dataflash@0 {
+				flash@0 {
 					compatible = "atmel,at45", "atmel,dataflash";
 					reg = <0>;
 					spi-max-frequency = <15000000>;
@@ -156,7 +156,7 @@
 					compatible = "ti,ads7843";
 					interrupts-extended = <&pioC 2 IRQ_TYPE_EDGE_BOTH>;
 					spi-max-frequency = <3000000>;
-					pendown-gpio = <&pioC 2 GPIO_ACTIVE_HIGH>;
+					pendown-gpio = <&pioC 2 GPIO_ACTIVE_LOW>;
 
 					ti,x-min = /bits/ 16 <150>;
 					ti,x-max = /bits/ 16 <3830>;
@@ -178,6 +178,10 @@
 				status = "okay";
 			};
 
+			rtc@fffffd20 {
+				atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
+			};
+
 			watchdog@fffffd40 {
 				status = "okay";
 			};
@@ -188,50 +192,50 @@
 	leds {
 		compatible = "gpio-leds";
 
-		ds8 {
+		led-ds8 {
 			label = "ds8";
 			gpios = <&pioA 13 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "none";
 		};
 
-		ds7 {
+		led-ds7 {
 			label = "ds7";
 			gpios = <&pioA 14 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "nand-disk";
 		};
 
-		ds1 {
+		led-ds1 {
 			label = "ds1";
 			gpios = <&pioA 23 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "heartbeat";
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		button_0 {
+		button-0 {
 			label = "button_0";
 			gpios = <&pioA 27 GPIO_ACTIVE_LOW>;
 			linux,code = <256>;
 			wakeup-source;
 		};
 
-		button_1 {
+		button-1 {
 			label = "button_1";
 			gpios = <&pioA 26 GPIO_ACTIVE_LOW>;
 			linux,code = <257>;
 			wakeup-source;
 		};
 
-		button_2 {
+		button-2 {
 			label = "button_2";
 			gpios = <&pioA 25 GPIO_ACTIVE_LOW>;
 			linux,code = <258>;
 			wakeup-source;
 		};
 
-		button_3 {
+		button-3 {
 			label = "button_3";
 			gpios = <&pioA 24 GPIO_ACTIVE_LOW>;
 			linux,code = <259>;
diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/microchip/at91sam9263.dtsi
index fe45d96239c9..a4b5d1f228f9 100644
--- a/arch/arm/boot/dts/at91sam9263.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9263.dtsi
@@ -9,6 +9,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	#address-cells = <1>;
@@ -100,7 +101,7 @@
 				atmel,external-irqs = <30 31>;
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,at91sam9263-pmc", "syscon";
 				reg = <0xfffffc00 0x100>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -151,13 +152,13 @@
 				clock-names = "t0_clk", "slow_clk";
 			};
 
-			rstc@fffffd00 {
+			reset-controller@fffffd00 {
 				compatible = "atmel,at91sam9260-rstc";
 				reg = <0xfffffd00 0x10>;
 				clocks = <&slow_xtal>;
 			};
 
-			shdwc@fffffd10 {
+			poweroff@fffffd10 {
 				compatible = "atmel,at91sam9260-shdwc";
 				reg = <0xfffffd10 0x10>;
 				clocks = <&slow_xtal>;
@@ -166,7 +167,7 @@
 			pinctrl@fffff200 {
 				#address-cells = <1>;
 				#size-cells = <1>;
-				compatible = "atmel,at91rm9200-pinctrl", "simple-bus";
+				compatible = "atmel,at91rm9200-pinctrl", "simple-mfd";
 				ranges = <0xfffff200 0xfffff200 0xa00>;
 
 				atmel,mux-mask = <
@@ -540,6 +541,7 @@
 			dbgu: serial@ffffee00 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xffffee00 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
@@ -551,6 +553,7 @@
 			usart0: serial@fff8c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfff8c000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -564,6 +567,7 @@
 			usart1: serial@fff90000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfff90000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -577,6 +581,7 @@
 			usart2: serial@fff94000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfff94000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <9 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -763,7 +768,7 @@
 			status = "disabled";
 		};
 
-		usb0: ohci@a00000 {
+		usb0: usb@a00000 {
 			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
 			reg = <0x00a00000 0x100000>;
 			interrupts = <29 IRQ_TYPE_LEVEL_HIGH 2>;
@@ -821,9 +826,8 @@
 
 	i2c-gpio-0 {
 		compatible = "i2c-gpio";
-		gpios = <&pioB 4 GPIO_ACTIVE_HIGH /* sda */
-			 &pioB 5 GPIO_ACTIVE_HIGH /* scl */
-			>;
+		sda-gpios = <&pioB 4 GPIO_ACTIVE_HIGH>;
+		scl-gpios = <&pioB 5 GPIO_ACTIVE_HIGH>;
 		i2c-gpio,sda-open-drain;
 		i2c-gpio,scl-open-drain;
 		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
diff --git a/arch/arm/boot/dts/at91sam9263ek.dts b/arch/arm/boot/dts/microchip/at91sam9263ek.dts
index 71f60576761a..93c5268a0845 100644
--- a/arch/arm/boot/dts/at91sam9263ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9263ek.dts
@@ -95,13 +95,17 @@
 			spi0: spi@fffa4000 {
 				status = "okay";
 				cs-gpios = <&pioA 5 0>, <0>, <0>, <0>;
-				mtd_dataflash@0 {
+				flash@0 {
 					compatible = "atmel,at45", "atmel,dataflash";
 					spi-max-frequency = <50000000>;
 					reg = <0>;
 				};
 			};
 
+			rtc@fffffd20 {
+				atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
+			};
+
 			watchdog@fffffd40 {
 				status = "okay";
 			};
@@ -148,7 +152,7 @@
 				nand@3 {
 					reg = <0x3 0x0 0x800000>;
 					rb-gpios = <&pioA 22 GPIO_ACTIVE_HIGH>;
-					cs-gpios = <&pioA 15 GPIO_ACTIVE_HIGH>;
+					cs-gpios = <&pioD 15 GPIO_ACTIVE_HIGH>;
 					nand-bus-width = <8>;
 					nand-ecc-mode = "soft";
 					nand-on-flash-bbt;
@@ -203,7 +207,7 @@
 			};
 		};
 
-		usb0: ohci@a00000 {
+		usb0: usb@a00000 {
 			num-ports = <2>;
 			status = "okay";
 			atmel,vbus-gpio = <&pioA 24 GPIO_ACTIVE_HIGH
@@ -215,30 +219,30 @@
 	leds {
 		compatible = "gpio-leds";
 
-		d3 {
+		led-d3 {
 			label = "d3";
 			gpios = <&pioB 7 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 
-		d2 {
+		led-d2 {
 			label = "d2";
 			gpios = <&pioC 29 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "nand-disk";
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		left_click {
+		button-left-click {
 			label = "left_click";
 			gpios = <&pioC 5 GPIO_ACTIVE_LOW>;
 			linux,code = <272>;
 			wakeup-source;
 		};
 
-		right_click {
+		button-right-click {
 			label = "right_click";
 			gpios = <&pioC 4 GPIO_ACTIVE_LOW>;
 			linux,code = <273>;
@@ -249,7 +253,7 @@
 	i2c-gpio-0 {
 		status = "okay";
 
-		24c512@50 {
+		eeprom@50 {
 			compatible = "atmel,24c512";
 			reg = <0x50>;
 			pagesize = <128>;
diff --git a/arch/arm/boot/dts/at91sam9g15.dtsi b/arch/arm/boot/dts/microchip/at91sam9g15.dtsi
index dde88276fe52..dde88276fe52 100644
--- a/arch/arm/boot/dts/at91sam9g15.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9g15.dtsi
diff --git a/arch/arm/boot/dts/at91sam9g15ek.dts b/arch/arm/boot/dts/microchip/at91sam9g15ek.dts
index 889a5097eb2d..889a5097eb2d 100644
--- a/arch/arm/boot/dts/at91sam9g15ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9g15ek.dts
diff --git a/arch/arm/boot/dts/at91sam9g20.dtsi b/arch/arm/boot/dts/microchip/at91sam9g20.dtsi
index 708e1646b7f4..738a43ffd228 100644
--- a/arch/arm/boot/dts/at91sam9g20.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9g20.dtsi
@@ -41,7 +41,7 @@
 				atmel,adc-startup-time = <40>;
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,at91sam9g20-pmc", "atmel,at91sam9260-pmc", "syscon";
 			};
 		};
diff --git a/arch/arm/boot/dts/at91sam9g20ek.dts b/arch/arm/boot/dts/microchip/at91sam9g20ek.dts
index 6de7a7cd3c07..1e62fd371ddb 100644
--- a/arch/arm/boot/dts/at91sam9g20ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9g20ek.dts
@@ -14,13 +14,13 @@
 	leds {
 		compatible = "gpio-leds";
 
-		ds1 {
+		led-ds1 {
 			label = "ds1";
 			gpios = <&pioA 9 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 
-		ds5 {
+		led-ds5 {
 			label = "ds5";
 			gpios = <&pioA 6 GPIO_ACTIVE_LOW>;
 		};
diff --git a/arch/arm/boot/dts/at91sam9g20ek_2mmc.dts b/arch/arm/boot/dts/microchip/at91sam9g20ek_2mmc.dts
index 2db95e8ffc64..3e5eab57d1a5 100644
--- a/arch/arm/boot/dts/at91sam9g20ek_2mmc.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9g20ek_2mmc.dts
@@ -12,7 +12,7 @@
 	compatible = "atmel,at91sam9g20ek_2mmc", "atmel,at91sam9g20", "atmel,at91sam9";
 
 	ahb {
-		apb{
+		apb {
 			mmc0: mmc@fffa8000 {
 				/* clk already mux wuth slot0 */
 				pinctrl-0 = <
@@ -40,13 +40,13 @@
 	leds {
 		compatible = "gpio-leds";
 
-		ds1 {
+		led-ds1 {
 			label = "ds1";
 			gpios = <&pioB 9 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 
-		ds5 {
+		led-ds5 {
 			label = "ds5";
 			gpios = <&pioB 8 GPIO_ACTIVE_LOW>;
 		};
diff --git a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi b/arch/arm/boot/dts/microchip/at91sam9g20ek_common.dtsi
index 87bb39060e8b..84a7287107f8 100644
--- a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9g20ek_common.dtsi
@@ -39,6 +39,13 @@
 
 				};
 
+				usb1 {
+					pinctrl_usb1_vbus_gpio: usb1_vbus_gpio {
+						atmel,pins =
+							<AT91_PIOC 5 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;	/* PC5 GPIO */
+					};
+				};
+
 				mmc0_slot1 {
 					pinctrl_board_mmc0_slot1: mmc0_slot1-board {
 						atmel,pins =
@@ -84,6 +91,8 @@
 			};
 
 			usb1: gadget@fffa4000 {
+				pinctrl-0 = <&pinctrl_usb1_vbus_gpio>;
+				pinctrl-names = "default";
 				atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>;
 				status = "okay";
 			};
@@ -110,14 +119,14 @@
 
 			spi0: spi@fffc8000 {
 				cs-gpios = <0>, <&pioC 11 0>, <0>, <0>;
-				mtd_dataflash@1 {
+				flash@1 {
 					compatible = "atmel,at45", "atmel,dataflash";
 					spi-max-frequency = <50000000>;
 					reg = <1>;
 				};
 			};
 
-			shdwc@fffffd10 {
+			shdwc: poweroff@fffffd10 {
 				atmel,wakeup-counter = <10>;
 				atmel,wakeup-rtt-timer;
 			};
@@ -202,7 +211,7 @@
 			};
 		};
 
-		usb0: ohci@500000 {
+		usb0: usb@500000 {
 			num-ports = <2>;
 			status = "okay";
 		};
@@ -211,28 +220,40 @@
 	i2c-gpio-0 {
 		status = "okay";
 
-		24c512@50 {
+		eeprom@50 {
 			compatible = "atmel,24c512";
 			reg = <0x50>;
+			vcc-supply = <&reg_3v3>;
 		};
 
 		wm8731: wm8731@1b {
 			compatible = "wm8731";
 			reg = <0x1b>;
+
+			/* PCK0 at 12MHz */
+			clocks = <&pmc PMC_TYPE_SYSTEM 8>;
+			clock-names = "mclk";
+			assigned-clocks = <&pmc PMC_TYPE_SYSTEM 8>;
+			assigned-clock-rates = <12000000>;
+
+			HPVDD-supply = <&vcc_dac>;
+			AVDD-supply = <&vcc_dac>;
+			DCVDD-supply = <&reg_3v3>;
+			DBVDD-supply = <&reg_3v3>;
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		btn3 {
+		button-3 {
 			label = "Button 3";
 			gpios = <&pioA 30 GPIO_ACTIVE_LOW>;
 			linux,code = <0x103>;
 			wakeup-source;
 		};
 
-		btn4 {
+		button-4 {
 			label = "Button 4";
 			gpios = <&pioA 31 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_PROG1>;
@@ -254,4 +275,35 @@
 		atmel,ssc-controller = <&ssc0>;
 		atmel,audio-codec = <&wm8731>;
 	};
+
+	reg_5v: fixedregulator0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_3v3: fixedregulator1 {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3";
+		vin-supply = <&reg_5v>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_1v: fixedregulator2 {
+		compatible = "regulator-fixed";
+		regulator-name = "1V";
+		vin-supply = <&reg_5v>;
+		regulator-min-microvolt = <1000000>;
+		regulator-max-microvolt = <1000000>;
+	};
+
+	vcc_dac: fixedregulator3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_DAC";
+		vin-supply = <&reg_3v3>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
 };
diff --git a/arch/arm/boot/dts/at91sam9g25-gardena-smart-gateway.dts b/arch/arm/boot/dts/microchip/at91sam9g25-gardena-smart-gateway.dts
index 7da70aeeb528..947c011c1b00 100644
--- a/arch/arm/boot/dts/at91sam9g25-gardena-smart-gateway.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9g25-gardena-smart-gateway.dts
@@ -23,7 +23,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		user_btn1 {
+		button {
 			label = "USER_BTN1";
 			gpios = <&pioA 24 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_PROG1>;
@@ -37,71 +37,71 @@
 	leds {
 		compatible = "gpio-leds";
 
-		power_blue {
+		led-power-blue {
 			label = "smartgw:power:blue";
 			gpios = <&pioC 21 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 		};
 
-		power_green {
+		led-power-green {
 			label = "smartgw:power:green";
 			gpios = <&pioC 20 GPIO_ACTIVE_HIGH>;
-			default-state = "on";
+			linux,default-trigger = "timer";
 		};
 
-		power_red {
+		led-power-red {
 			label = "smartgw:power:red";
 			gpios = <&pioC 19 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 		};
 
-		radio_blue {
+		led-radio-blue {
 			label = "smartgw:radio:blue";
 			gpios = <&pioC 18 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 		};
 
-		radio_green {
+		led-radio-green {
 			label = "smartgw:radio:green";
 			gpios = <&pioC 17 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 		};
 
-		radio_red {
+		led-radio-red {
 			label = "smartgw:radio:red";
 			gpios = <&pioC 16 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 		};
 
-		internet_blue {
+		led-internet-blue {
 			label = "smartgw:internet:blue";
 			gpios = <&pioC 15 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 		};
 
-		internet_green {
+		led-internet-green {
 			label = "smartgw:internet:green";
 			gpios = <&pioC 14 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 		};
 
-		internet_red {
+		led-internet-red {
 			label = "smartgw:internet:red";
 			gpios = <&pioC 13 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 		};
 
-		heartbeat {
+		led-heartbeat {
 			label = "smartgw:heartbeat";
 			gpios = <&pioB 8 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 
-		pb18 {
+		led-pb18 {
 			status = "disabled";
 		};
 
-		pd21 {
+		led-pd21 {
 			status = "disabled";
 		};
 	};
@@ -121,6 +121,8 @@
 };
 
 &usart3 {
+	atmel,use-dma-rx;
+	atmel,use-dma-tx;
 	status = "okay";
 
 	pinctrl-0 = <&pinctrl_usart3
diff --git a/arch/arm/boot/dts/at91sam9g25.dtsi b/arch/arm/boot/dts/microchip/at91sam9g25.dtsi
index d2f13afb35ea..ec3c77221881 100644
--- a/arch/arm/boot/dts/at91sam9g25.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9g25.dtsi
@@ -26,7 +26,7 @@
 				      >;
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,at91sam9g25-pmc", "atmel,at91sam9x5-pmc", "syscon";
 			};
 		};
diff --git a/arch/arm/boot/dts/at91sam9g25ek.dts b/arch/arm/boot/dts/microchip/at91sam9g25ek.dts
index 61b0bdb615dc..61b0bdb615dc 100644
--- a/arch/arm/boot/dts/at91sam9g25ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9g25ek.dts
diff --git a/arch/arm/boot/dts/at91sam9g35.dtsi b/arch/arm/boot/dts/microchip/at91sam9g35.dtsi
index 48c2bc4a7753..c9cfb93092ee 100644
--- a/arch/arm/boot/dts/at91sam9g35.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9g35.dtsi
@@ -25,7 +25,7 @@
 				      >;
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,at91sam9g35-pmc", "atmel,at91sam9x5-pmc", "syscon";
 			};
 		};
diff --git a/arch/arm/boot/dts/at91sam9g35ek.dts b/arch/arm/boot/dts/microchip/at91sam9g35ek.dts
index f966b56de63c..f966b56de63c 100644
--- a/arch/arm/boot/dts/at91sam9g35ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9g35ek.dts
diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/microchip/at91sam9g45.dtsi
index 2ab730fd6472..4e00ed2d3ecd 100644
--- a/arch/arm/boot/dts/at91sam9g45.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9g45.dtsi
@@ -13,6 +13,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	#address-cells = <1>;
@@ -69,7 +70,7 @@
 			clock-frequency = <0>;
 		};
 
-		adc_op_clk: adc_op_clk{
+		adc_op_clk: adc_op_clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <300000>;
@@ -128,7 +129,7 @@
 				reg = <0xffffea00 0x200>;
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,at91sam9g45-pmc", "syscon";
 				reg = <0xfffffc00 0x100>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -137,7 +138,7 @@
 				clock-names = "slow_clk", "main_xtal";
 			};
 
-			rstc@fffffd00 {
+			reset-controller@fffffd00 {
 				compatible = "atmel,at91sam9g45-rstc";
 				reg = <0xfffffd00 0x10>;
 				clocks = <&clk32k>;
@@ -151,7 +152,7 @@
 			};
 
 
-			shdwc@fffffd10 {
+			poweroff@fffffd10 {
 				compatible = "atmel,at91sam9rl-shdwc";
 				reg = <0xfffffd10 0x10>;
 				clocks = <&clk32k>;
@@ -189,7 +190,7 @@
 			pinctrl@fffff200 {
 				#address-cells = <1>;
 				#size-cells = <1>;
-				compatible = "atmel,at91rm9200-pinctrl", "simple-bus";
+				compatible = "atmel,at91rm9200-pinctrl", "simple-mfd";
 				ranges = <0xfffff200 0xfffff200 0xa00>;
 
 				atmel,mux-mask = <
@@ -675,6 +676,7 @@
 
 			dbgu: serial@ffffee00 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				reg = <0xffffee00 0x200>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
@@ -687,6 +689,7 @@
 			usart0: serial@fff8c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfff8c000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -700,6 +703,7 @@
 			usart1: serial@fff90000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfff90000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -713,6 +717,7 @@
 			usart2: serial@fff94000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfff94000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <9 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -726,6 +731,7 @@
 			usart3: serial@fff98000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfff98000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <10 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -747,7 +753,7 @@
 				status = "disabled";
 			};
 
-			trng@fffcc000 {
+			trng: rng@fffcc000 {
 				compatible = "atmel,at91sam9g45-trng";
 				reg = <0xfffcc000 0x100>;
 				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 0>;
@@ -917,7 +923,7 @@
 				status = "disabled";
 			};
 
-			clk32k: sckc@fffffd50 {
+			clk32k: clock-controller@fffffd50 {
 				compatible = "atmel,at91sam9x5-sckc";
 				reg = <0xfffffd50 0x4>;
 				clocks = <&slow_xtal>;
@@ -958,7 +964,7 @@
 			status = "disabled";
 		};
 
-		usb0: ohci@700000 {
+		usb0: usb@700000 {
 			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
 			reg = <0x00700000 0x100000>;
 			interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
@@ -967,7 +973,7 @@
 			status = "disabled";
 		};
 
-		usb1: ehci@800000 {
+		usb1: usb@800000 {
 			compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
 			reg = <0x00800000 0x100000>;
 			interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
@@ -1004,9 +1010,8 @@
 
 	i2c-gpio-0 {
 		compatible = "i2c-gpio";
-		gpios = <&pioA 20 GPIO_ACTIVE_HIGH /* sda */
-			 &pioA 21 GPIO_ACTIVE_HIGH /* scl */
-			>;
+		sda-gpios = <&pioA 20 GPIO_ACTIVE_HIGH>;
+		scl-gpios = <&pioA 21 GPIO_ACTIVE_HIGH>;
 		i2c-gpio,sda-open-drain;
 		i2c-gpio,scl-open-drain;
 		i2c-gpio,delay-us = <5>;	/* ~100 kHz */
diff --git a/arch/arm/boot/dts/at91sam9m10g45ek.dts b/arch/arm/boot/dts/microchip/at91sam9m10g45ek.dts
index b6256a20fbc7..2a31b2f14893 100644
--- a/arch/arm/boot/dts/at91sam9m10g45ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9m10g45ek.dts
@@ -164,10 +164,10 @@
 				};
 			};
 
-			spi0: spi@fffa4000{
+			spi0: spi@fffa4000 {
 				status = "okay";
 				cs-gpios = <&pioB 3 0>, <0>, <0>, <0>;
-				mtd_dataflash@0 {
+				flash@0 {
 					compatible = "atmel,at45", "atmel,dataflash";
 					spi-max-frequency = <13000000>;
 					reg = <0>;
@@ -303,14 +303,14 @@
 			};
 		};
 
-		usb0: ohci@700000 {
+		usb0: usb@700000 {
 			status = "okay";
 			num-ports = <2>;
 			atmel,vbus-gpio = <&pioD 1 GPIO_ACTIVE_LOW
 					   &pioD 3 GPIO_ACTIVE_LOW>;
 		};
 
-		usb1: ehci@800000 {
+		usb1: usb@800000 {
 			status = "okay";
 		};
 	};
@@ -343,48 +343,48 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		left_click {
+		button-left-click {
 			label = "left_click";
 			gpios = <&pioB 6 GPIO_ACTIVE_LOW>;
 			linux,code = <272>;
 			wakeup-source;
 		};
 
-		right_click {
+		button-right-click {
 			label = "right_click";
 			gpios = <&pioB 7 GPIO_ACTIVE_LOW>;
 			linux,code = <273>;
 			wakeup-source;
 		};
 
-		left {
+		button-left {
 			label = "Joystick Left";
 			gpios = <&pioB 14 GPIO_ACTIVE_LOW>;
 			linux,code = <105>;
 		};
 
-		right {
+		button-right {
 			label = "Joystick Right";
 			gpios = <&pioB 15 GPIO_ACTIVE_LOW>;
 			linux,code = <106>;
 		};
 
-		up {
+		button-up {
 			label = "Joystick Up";
 			gpios = <&pioB 16 GPIO_ACTIVE_LOW>;
 			linux,code = <103>;
 		};
 
-		down {
+		button-down {
 			label = "Joystick Down";
 			gpios = <&pioB 17 GPIO_ACTIVE_LOW>;
 			linux,code = <108>;
 		};
 
-		enter {
+		button-enter {
 			label = "Joystick Press";
 			gpios = <&pioB 18 GPIO_ACTIVE_LOW>;
 			linux,code = <28>;
diff --git a/arch/arm/boot/dts/at91sam9n12.dtsi b/arch/arm/boot/dts/microchip/at91sam9n12.dtsi
index 0785389f5507..af41c3dbb4bf 100644
--- a/arch/arm/boot/dts/at91sam9n12.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9n12.dtsi
@@ -11,6 +11,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	#address-cells = <1>;
@@ -117,7 +118,7 @@
 				reg = <0xffffea00 0x200>;
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,at91sam9n12-pmc", "syscon";
 				reg = <0xfffffc00 0x200>;
 				#clock-cells = <2>;
@@ -126,7 +127,7 @@
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 			};
 
-			rstc@fffffe00 {
+			reset-controller@fffffe00 {
 				compatible = "atmel,at91sam9g45-rstc";
 				reg = <0xfffffe00 0x10>;
 				clocks = <&clk32k>;
@@ -139,34 +140,17 @@
 				clocks = <&pmc PMC_TYPE_CORE PMC_MCK>;
 			};
 
-			shdwc@fffffe10 {
+			poweroff@fffffe10 {
 				compatible = "atmel,at91sam9x5-shdwc";
 				reg = <0xfffffe10 0x10>;
 				clocks = <&clk32k>;
 			};
 
-			sckc@fffffe50 {
+			clk32k: clock-controller@fffffe50 {
 				compatible = "atmel,at91sam9x5-sckc";
 				reg = <0xfffffe50 0x4>;
-
-				slow_osc: slow_osc {
-					compatible = "atmel,at91sam9x5-clk-slow-osc";
-					#clock-cells = <0>;
-					clocks = <&slow_xtal>;
-				};
-
-				slow_rc_osc: slow_rc_osc {
-					compatible = "atmel,at91sam9x5-clk-slow-rc-osc";
-					#clock-cells = <0>;
-					clock-frequency = <32768>;
-					clock-accuracy = <50000000>;
-				};
-
-				clk32k: slck {
-					compatible = "atmel,at91sam9x5-clk-slow";
-					#clock-cells = <0>;
-					clocks = <&slow_rc_osc>, <&slow_osc>;
-				};
+				clocks = <&slow_xtal>;
+				#clock-cells = <0>;
 			};
 
 			mmc0: mmc@f0008000 {
@@ -242,7 +226,7 @@
 			pinctrl@fffff400 {
 				#address-cells = <1>;
 				#size-cells = <1>;
-				compatible = "atmel,at91sam9x5-pinctrl", "atmel,at91rm9200-pinctrl", "simple-bus";
+				compatible = "atmel,at91sam9x5-pinctrl", "simple-mfd";
 				ranges = <0xfffff400 0xfffff400 0x800>;
 
 				atmel,mux-mask = <
@@ -593,6 +577,7 @@
 			dbgu: serial@fffff200 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xfffff200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
@@ -618,6 +603,7 @@
 			usart0: serial@f801c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf801c000 0x4000>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <5 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart0>;
@@ -629,6 +615,7 @@
 			usart1: serial@f8020000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8020000 0x4000>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart1>;
@@ -640,6 +627,7 @@
 			usart2: serial@f8024000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8024000 0x4000>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart2>;
@@ -651,6 +639,7 @@
 			usart3: serial@f8028000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8028000 0x4000>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart3>;
@@ -759,7 +748,7 @@
 			};
 		};
 
-		usb0: ohci@500000 {
+		usb0: usb@500000 {
 			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
 			reg = <0x00500000 0x00100000>;
 			interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
@@ -797,9 +786,8 @@
 
 	i2c-gpio-0 {
 		compatible = "i2c-gpio";
-		gpios = <&pioA 30 GPIO_ACTIVE_HIGH /* sda */
-			 &pioA 31 GPIO_ACTIVE_HIGH /* scl */
-			>;
+		sda-gpios = <&pioA 30 GPIO_ACTIVE_HIGH>;
+		scl-gpios = <&pioA 31 GPIO_ACTIVE_HIGH>;
 		i2c-gpio,sda-open-drain;
 		i2c-gpio,scl-open-drain;
 		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
diff --git a/arch/arm/boot/dts/at91sam9n12ek.dts b/arch/arm/boot/dts/microchip/at91sam9n12ek.dts
index 2bc4e6e0a923..b06a54e8e237 100644
--- a/arch/arm/boot/dts/at91sam9n12ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9n12ek.dts
@@ -119,7 +119,7 @@
 			spi0: spi@f0000000 {
 				status = "okay";
 				cs-gpios = <&pioA 14 0>, <0>, <0>, <0>;
-				m25p80@0 {
+				flash@0 {
 					compatible = "atmel,at25df321a";
 					spi-max-frequency = <50000000>;
 					reg = <0>;
@@ -180,7 +180,7 @@
 			};
 		};
 
-		usb0: ohci@500000 {
+		usb0: usb@500000 {
 			num-ports = <1>;
 			atmel,vbus-gpio = <&pioB 7 GPIO_ACTIVE_LOW>;
 			status = "okay";
@@ -207,29 +207,29 @@
 	leds {
 		compatible = "gpio-leds";
 
-		d8 {
+		led-d8 {
 			label = "d8";
 			gpios = <&pioB 4 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "mmc0";
 		};
 
-		d9 {
+		led-d9 {
 			label = "d9";
 			gpios = <&pioB 5 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "nand-disk";
 		};
 
-		d10 {
+		led-d10 {
 			label = "d10";
 			gpios = <&pioB 6 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		enter {
+		button-enter {
 			label = "Enter";
 			gpios = <&pioB 3 GPIO_ACTIVE_LOW>;
 			linux,code = <28>;
diff --git a/arch/arm/boot/dts/at91sam9rl.dtsi b/arch/arm/boot/dts/microchip/at91sam9rl.dtsi
index 730d1182c73e..de74cf2980a0 100644
--- a/arch/arm/boot/dts/at91sam9rl.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9rl.dtsi
@@ -11,6 +11,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	#address-cells = <1>;
@@ -66,7 +67,7 @@
 			clock-frequency = <0>;
 		};
 
-		adc_op_clk: adc_op_clk{
+		adc_op_clk: adc_op_clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <1000000>;
@@ -175,6 +176,7 @@
 			usart0: serial@fffb0000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffb0000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -188,6 +190,7 @@
 			usart1: serial@fffb4000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffb4000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -201,6 +204,7 @@
 			usart2: serial@fffb8000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffb8000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -214,6 +218,7 @@
 			usart3: serial@fffbc000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffbc000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <9 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -322,6 +327,7 @@
 			dbgu: serial@fffff200 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xfffff200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
@@ -333,7 +339,7 @@
 			pinctrl@fffff400 {
 				#address-cells = <1>;
 				#size-cells = <1>;
-				compatible = "atmel,at91rm9200-pinctrl", "simple-bus";
+				compatible = "atmel,at91rm9200-pinctrl", "simple-mfd";
 				ranges = <0xfffff400 0xfffff400 0x800>;
 
 				atmel,mux-mask =
@@ -757,7 +763,7 @@
 				};
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,at91sam9rl-pmc", "syscon";
 				reg = <0xfffffc00 0x100>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -766,13 +772,13 @@
 				clock-names = "slow_clk", "main_xtal";
 			};
 
-			rstc@fffffd00 {
+			reset-controller@fffffd00 {
 				compatible = "atmel,at91sam9260-rstc";
 				reg = <0xfffffd00 0x10>;
 				clocks = <&clk32k>;
 			};
 
-			shdwc@fffffd10 {
+			poweroff@fffffd10 {
 				compatible = "atmel,at91sam9260-shdwc";
 				reg = <0xfffffd10 0x10>;
 				clocks = <&clk32k>;
@@ -793,7 +799,7 @@
 				status = "disabled";
 			};
 
-			clk32k: sckc@fffffd50 {
+			clk32k: clock-controller@fffffd50 {
 				compatible = "atmel,at91sam9x5-sckc";
 				reg = <0xfffffd50 0x4>;
 				clocks = <&slow_xtal>;
@@ -827,8 +833,8 @@
 
 	i2c-gpio-0 {
 		compatible = "i2c-gpio";
-		gpios = <&pioA 23 GPIO_ACTIVE_HIGH>, /* sda */
-			<&pioA 24 GPIO_ACTIVE_HIGH>; /* scl */
+		sda-gpios = <&pioA 23 GPIO_ACTIVE_HIGH>;
+		scl-gpios = <&pioA 24 GPIO_ACTIVE_HIGH>;
 		i2c-gpio,sda-open-drain;
 		i2c-gpio,scl-open-drain;
 		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
@@ -841,8 +847,8 @@
 
 	i2c-gpio-1 {
 		compatible = "i2c-gpio";
-		gpios = <&pioD 10 GPIO_ACTIVE_HIGH>, /* sda */
-			<&pioD 11 GPIO_ACTIVE_HIGH>; /* scl */
+		sda-gpios = <&pioD 10 GPIO_ACTIVE_HIGH>;
+		scl-gpios = <&pioD 11 GPIO_ACTIVE_HIGH>;
 		i2c-gpio,sda-open-drain;
 		i2c-gpio,scl-open-drain;
 		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
diff --git a/arch/arm/boot/dts/at91sam9rlek.dts b/arch/arm/boot/dts/microchip/at91sam9rlek.dts
index 62981b39c815..a57351270551 100644
--- a/arch/arm/boot/dts/at91sam9rlek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9rlek.dts
@@ -180,7 +180,7 @@
 			spi0: spi@fffcc000 {
 				status = "okay";
 				cs-gpios = <&pioA 28 0>, <0>, <0>, <0>;
-				mtd_dataflash@0 {
+				flash@0 {
 					compatible = "atmel,at45", "atmel,dataflash";
 					spi-max-frequency = <15000000>;
 					reg = <0>;
@@ -212,6 +212,10 @@
 				status = "okay";
 			};
 
+			rtc@fffffd20 {
+				atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
+			};
+
 			rtc@fffffe00 {
 				status = "okay";
 			};
@@ -244,17 +248,17 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		right_click {
+		button-right-click {
 			label = "right_click";
 			gpios = <&pioB 0 GPIO_ACTIVE_LOW>;
 			linux,code = <273>;
 			wakeup-source;
 		};
 
-		left_click {
+		button-left-click {
 			label = "left_click";
 			gpios = <&pioB 1 GPIO_ACTIVE_LOW>;
 			linux,code = <272>;
diff --git a/arch/arm/boot/dts/at91sam9x25.dtsi b/arch/arm/boot/dts/microchip/at91sam9x25.dtsi
index 0fe8802e1242..7036f5f04571 100644
--- a/arch/arm/boot/dts/at91sam9x25.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9x25.dtsi
@@ -27,7 +27,7 @@
 				      >;
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,at91sam9x25-pmc", "atmel,at91sam9x5-pmc", "syscon";
 			};
 		};
diff --git a/arch/arm/boot/dts/at91sam9x25ek.dts b/arch/arm/boot/dts/microchip/at91sam9x25ek.dts
index ad7c6b36f0ba..ad7c6b36f0ba 100644
--- a/arch/arm/boot/dts/at91sam9x25ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9x25ek.dts
diff --git a/arch/arm/boot/dts/at91sam9x35.dtsi b/arch/arm/boot/dts/microchip/at91sam9x35.dtsi
index 0bfa21f18f87..eb03b0497e37 100644
--- a/arch/arm/boot/dts/at91sam9x35.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9x35.dtsi
@@ -26,7 +26,7 @@
 				      >;
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,at91sam9x35-pmc", "atmel,at91sam9x5-pmc", "syscon";
 			};
 		};
diff --git a/arch/arm/boot/dts/at91sam9x35ek.dts b/arch/arm/boot/dts/microchip/at91sam9x35ek.dts
index 66675c787b97..66675c787b97 100644
--- a/arch/arm/boot/dts/at91sam9x35ek.dts
+++ b/arch/arm/boot/dts/microchip/at91sam9x35ek.dts
diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/microchip/at91sam9x5.dtsi
index 395e883644cd..9070fd06995a 100644
--- a/arch/arm/boot/dts/at91sam9x5.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9x5.dtsi
@@ -13,6 +13,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	#address-cells = <1>;
@@ -67,7 +68,7 @@
 			clock-frequency = <0>;
 		};
 
-		adc_op_clk: adc_op_clk{
+		adc_op_clk: adc_op_clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <1000000>;
@@ -125,7 +126,7 @@
 				reg = <0xffffea00 0x200>;
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,at91sam9x5-pmc", "syscon";
 				reg = <0xfffffc00 0x200>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -134,13 +135,13 @@
 				clock-names = "slow_clk", "main_xtal";
 			};
 
-			reset_controller: rstc@fffffe00 {
+			reset_controller: reset-controller@fffffe00 {
 				compatible = "atmel,at91sam9g45-rstc";
 				reg = <0xfffffe00 0x10>;
 				clocks = <&clk32k>;
 			};
 
-			shutdown_controller: shdwc@fffffe10 {
+			shutdown_controller: poweroff@fffffe10 {
 				compatible = "atmel,at91sam9x5-shdwc";
 				reg = <0xfffffe10 0x10>;
 				clocks = <&clk32k>;
@@ -153,7 +154,7 @@
 				clocks = <&pmc PMC_TYPE_CORE PMC_MCK>;
 			};
 
-			clk32k: sckc@fffffe50 {
+			clk32k: clock-controller@fffffe50 {
 				compatible = "atmel,at91sam9x5-sckc";
 				reg = <0xfffffe50 0x4>;
 				clocks = <&slow_xtal>;
@@ -201,7 +202,7 @@
 			pinctrl: pinctrl@fffff400 {
 				#address-cells = <1>;
 				#size-cells = <1>;
-				compatible = "atmel,at91sam9x5-pinctrl", "atmel,at91rm9200-pinctrl", "simple-bus";
+				compatible = "atmel,at91sam9x5-pinctrl", "simple-mfd";
 				ranges = <0xfffff400 0xfffff400 0x800>;
 
 				/* shared pinctrl settings */
@@ -674,6 +675,7 @@
 			dbgu: serial@fffff200 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xfffff200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
@@ -688,6 +690,7 @@
 			usart0: serial@f801c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf801c000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <5 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart0>;
@@ -702,6 +705,7 @@
 			usart1: serial@f8020000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8020000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart1>;
@@ -716,6 +720,7 @@
 			usart2: serial@f8024000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8024000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart2>;
@@ -775,6 +780,7 @@
 			uart0: serial@f8040000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8040000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_uart0>;
@@ -786,6 +792,7 @@
 			uart1: serial@f8044000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8044000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <16 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_uart1>;
@@ -879,7 +886,7 @@
 			};
 		};
 
-		usb0: ohci@600000 {
+		usb0: usb@600000 {
 			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
 			reg = <0x00600000 0x100000>;
 			interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
@@ -888,7 +895,7 @@
 			status = "disabled";
 		};
 
-		usb1: ehci@700000 {
+		usb1: usb@700000 {
 			compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
 			reg = <0x00700000 0x100000>;
 			interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
@@ -926,9 +933,8 @@
 
 	i2c-gpio-0 {
 		compatible = "i2c-gpio";
-		gpios = <&pioA 30 GPIO_ACTIVE_HIGH /* sda */
-			 &pioA 31 GPIO_ACTIVE_HIGH /* scl */
-			>;
+		sda-gpios = <&pioA 30 GPIO_ACTIVE_HIGH>;
+		scl-gpios = <&pioA 31 GPIO_ACTIVE_HIGH>;
 		i2c-gpio,sda-open-drain;
 		i2c-gpio,scl-open-drain;
 		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
@@ -941,9 +947,8 @@
 
 	i2c-gpio-1 {
 		compatible = "i2c-gpio";
-		gpios = <&pioC 0 GPIO_ACTIVE_HIGH /* sda */
-			 &pioC 1 GPIO_ACTIVE_HIGH /* scl */
-			>;
+		sda-gpios = <&pioC 0 GPIO_ACTIVE_HIGH>;
+		scl-gpios = <&pioC 1 GPIO_ACTIVE_HIGH>;
 		i2c-gpio,sda-open-drain;
 		i2c-gpio,scl-open-drain;
 		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
@@ -956,9 +961,8 @@
 
 	i2c-gpio-2 {
 		compatible = "i2c-gpio";
-		gpios = <&pioB 4 GPIO_ACTIVE_HIGH /* sda */
-			 &pioB 5 GPIO_ACTIVE_HIGH /* scl */
-			>;
+		sda-gpios = <&pioB 4 GPIO_ACTIVE_HIGH>;
+		scl-gpios = <&pioB 5 GPIO_ACTIVE_HIGH>;
 		i2c-gpio,sda-open-drain;
 		i2c-gpio,scl-open-drain;
 		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
diff --git a/arch/arm/boot/dts/at91sam9x5_can.dtsi b/arch/arm/boot/dts/microchip/at91sam9x5_can.dtsi
index 04ccb25d342c..04ccb25d342c 100644
--- a/arch/arm/boot/dts/at91sam9x5_can.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9x5_can.dtsi
diff --git a/arch/arm/boot/dts/at91sam9x5_isi.dtsi b/arch/arm/boot/dts/microchip/at91sam9x5_isi.dtsi
index 4ce98f05d7db..4ce98f05d7db 100644
--- a/arch/arm/boot/dts/at91sam9x5_isi.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9x5_isi.dtsi
diff --git a/arch/arm/boot/dts/at91sam9x5_lcd.dtsi b/arch/arm/boot/dts/microchip/at91sam9x5_lcd.dtsi
index f81c9d1691e0..f81c9d1691e0 100644
--- a/arch/arm/boot/dts/at91sam9x5_lcd.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9x5_lcd.dtsi
diff --git a/arch/arm/boot/dts/at91sam9x5_macb0.dtsi b/arch/arm/boot/dts/microchip/at91sam9x5_macb0.dtsi
index 222aa30f6860..222aa30f6860 100644
--- a/arch/arm/boot/dts/at91sam9x5_macb0.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9x5_macb0.dtsi
diff --git a/arch/arm/boot/dts/at91sam9x5_macb1.dtsi b/arch/arm/boot/dts/microchip/at91sam9x5_macb1.dtsi
index 26bf9b5de9ee..26bf9b5de9ee 100644
--- a/arch/arm/boot/dts/at91sam9x5_macb1.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9x5_macb1.dtsi
diff --git a/arch/arm/boot/dts/at91sam9x5_usart3.dtsi b/arch/arm/boot/dts/microchip/at91sam9x5_usart3.dtsi
index 098d3fef5c37..a47c765e1b20 100644
--- a/arch/arm/boot/dts/at91sam9x5_usart3.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9x5_usart3.dtsi
@@ -8,6 +8,7 @@
 
 #include <dt-bindings/pinctrl/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	aliases {
@@ -44,6 +45,7 @@
 			usart3: serial@f8028000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8028000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart3>;
diff --git a/arch/arm/boot/dts/at91sam9x5cm.dtsi b/arch/arm/boot/dts/microchip/at91sam9x5cm.dtsi
index cdd37f67280b..fb3c19bdfcb6 100644
--- a/arch/arm/boot/dts/at91sam9x5cm.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9x5cm.dtsi
@@ -120,13 +120,13 @@
 	leds {
 		compatible = "gpio-leds";
 
-		pb18 {
+		led-pb18 {
 			label = "pb18";
 			gpios = <&pioB 18 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "heartbeat";
 		};
 
-		pd21 {
+		led-pd21 {
 			label = "pd21";
 			gpios = <&pioD 21 GPIO_ACTIVE_HIGH>;
 		};
diff --git a/arch/arm/boot/dts/at91sam9x5dm.dtsi b/arch/arm/boot/dts/microchip/at91sam9x5dm.dtsi
index a9278038af3b..a9278038af3b 100644
--- a/arch/arm/boot/dts/at91sam9x5dm.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9x5dm.dtsi
diff --git a/arch/arm/boot/dts/at91sam9x5ek.dtsi b/arch/arm/boot/dts/microchip/at91sam9x5ek.dtsi
index 6d1264de6060..9618b8d965b0 100644
--- a/arch/arm/boot/dts/at91sam9x5ek.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9x5ek.dtsi
@@ -39,6 +39,8 @@
 };
 
 &dbgu {
+	atmel,use-dma-rx;
+	atmel,use-dma-tx;
 	status = "okay";
 };
 
@@ -125,7 +127,7 @@
 	cs-gpios = <&pioA 14 0>, <0>, <0>, <0>;
 	status = "disabled"; /* conflicts with mmc1 */
 
-	m25p80@0 {
+	flash@0 {
 		compatible = "atmel,at25df321a";
 		spi-max-frequency = <50000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/at91sam9xe.dtsi b/arch/arm/boot/dts/microchip/at91sam9xe.dtsi
index f571f77779c3..f571f77779c3 100644
--- a/arch/arm/boot/dts/at91sam9xe.dtsi
+++ b/arch/arm/boot/dts/microchip/at91sam9xe.dtsi
diff --git a/arch/arm/boot/dts/ethernut5.dts b/arch/arm/boot/dts/microchip/ethernut5.dts
index ad7a0850252a..52ccef31b391 100644
--- a/arch/arm/boot/dts/ethernut5.dts
+++ b/arch/arm/boot/dts/microchip/ethernut5.dts
@@ -101,7 +101,7 @@
 			};
 		};
 
-		usb0: ohci@500000 {
+		usb0: usb@500000 {
 			num-ports = <2>;
 			status = "okay";
 		};
diff --git a/arch/arm/boot/dts/evk-pro3.dts b/arch/arm/boot/dts/microchip/evk-pro3.dts
index 6d519d02d190..40c5111c2f0a 100644
--- a/arch/arm/boot/dts/evk-pro3.dts
+++ b/arch/arm/boot/dts/microchip/evk-pro3.dts
@@ -45,7 +45,7 @@
 			};
 		};
 
-		usb0: ohci@500000 {
+		usb0: usb@500000 {
 			num-ports = <2>;
 			status = "okay";
 		};
diff --git a/arch/arm/boot/dts/ge863-pro3.dtsi b/arch/arm/boot/dts/microchip/ge863-pro3.dtsi
index dbba33e5a06c..dbba33e5a06c 100644
--- a/arch/arm/boot/dts/ge863-pro3.dtsi
+++ b/arch/arm/boot/dts/microchip/ge863-pro3.dtsi
diff --git a/arch/arm/boot/dts/microchip/lan966x-kontron-kswitch-d10-mmt-6g-2gs.dts b/arch/arm/boot/dts/microchip/lan966x-kontron-kswitch-d10-mmt-6g-2gs.dts
new file mode 100644
index 000000000000..0f555eb45bda
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/lan966x-kontron-kswitch-d10-mmt-6g-2gs.dts
@@ -0,0 +1,94 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for the Kontron KSwitch D10 MMT 6G-2GS
+ */
+
+/dts-v1/;
+#include "lan966x-kontron-kswitch-d10-mmt.dtsi"
+
+/ {
+	model = "Kontron KSwitch D10 MMT 6G-2GS";
+	compatible = "kontron,kswitch-d10-mmt-6g-2gs", "kontron,s1921",
+		     "microchip,lan9668", "microchip,lan966";
+
+	aliases {
+		i2c0 = &i2c4;
+		i2c1 = &i2c1;
+	};
+
+	sfp0: sfp0 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c4>;
+		los-gpios = <&sgpio_in 1 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in 1 1 GPIO_ACTIVE_LOW>;
+		maximum-power-milliwatt = <2500>;
+		tx-disable-gpios = <&sgpio_out 3 0 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in 0 2 GPIO_ACTIVE_HIGH>;
+		rate-select0-gpios = <&sgpio_out 2 0 GPIO_ACTIVE_HIGH>;
+		rate-select1-gpios = <&sgpio_out 2 1 GPIO_ACTIVE_HIGH>;
+	};
+
+	sfp1: sfp1 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c1>;
+		los-gpios = <&sgpio_in 1 2 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in 1 3 GPIO_ACTIVE_LOW>;
+		maximum-power-milliwatt = <2500>;
+		tx-disable-gpios = <&sgpio_out 3 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in 0 3 GPIO_ACTIVE_HIGH>;
+		rate-select0-gpios = <&sgpio_out 2 2 GPIO_ACTIVE_HIGH>;
+		rate-select1-gpios = <&sgpio_out 2 3 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&flx1 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+
+	i2c1: i2c@600 {
+		pinctrl-0 = <&fc1_c_pins>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+};
+
+&flx4 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+
+	i2c4: i2c@600 {
+		pinctrl-0 = <&fc4_b_pins>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+};
+
+&gpio {
+	fc1_c_pins: fc1-c-i2c-pins {
+		/* SCL, SDA */
+		pins = "GPIO_47", "GPIO_48";
+		function = "fc1_c";
+	};
+
+	fc4_b_pins: fc4-b-i2c-pins {
+		/* SCL, SDA */
+		pins = "GPIO_57", "GPIO_58";
+		function = "fc4_b";
+	};
+};
+
+&port2 {
+	phys = <&serdes 2 SERDES6G(0)>;
+	sfp = <&sfp0>;
+	managed = "in-band-status";
+	phy-mode = "sgmii";
+	status = "okay";
+};
+
+&port3 {
+	phys = <&serdes 3 SERDES6G(1)>;
+	sfp = <&sfp1>;
+	managed = "in-band-status";
+	phy-mode = "sgmii";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/microchip/lan966x-kontron-kswitch-d10-mmt-8g.dts b/arch/arm/boot/dts/microchip/lan966x-kontron-kswitch-d10-mmt-8g.dts
new file mode 100644
index 000000000000..ad5d8b56e6fa
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/lan966x-kontron-kswitch-d10-mmt-8g.dts
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for the Kontron KSwitch D10 MMT 8G
+ */
+
+/dts-v1/;
+#include "lan966x-kontron-kswitch-d10-mmt.dtsi"
+
+/ {
+	model = "Kontron KSwitch D10 MMT 8G";
+	compatible = "kontron,kswitch-d10-mmt-8g", "kontron,s1921",
+		     "microchip,lan9668", "microchip,lan966";
+};
+
+&mdio0 {
+	phy2: ethernet-phy@3 {
+		reg = <3>;
+		interrupts-extended = <&gpio 24 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	phy3: ethernet-phy@4 {
+		reg = <4>;
+		interrupts-extended = <&gpio 24 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&port2 {
+	phys = <&serdes 2 SERDES6G(0)>;
+	phy-handle = <&phy2>;
+	phy-mode = "sgmii";
+	managed = "in-band-status";
+	status = "okay";
+};
+
+&port3 {
+	phys = <&serdes 3 SERDES6G(1)>;
+	phy-handle = <&phy3>;
+	phy-mode = "sgmii";
+	managed = "in-band-status";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/microchip/lan966x-kontron-kswitch-d10-mmt.dtsi b/arch/arm/boot/dts/microchip/lan966x-kontron-kswitch-d10-mmt.dtsi
new file mode 100644
index 000000000000..426893750d51
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/lan966x-kontron-kswitch-d10-mmt.dtsi
@@ -0,0 +1,230 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Common part of the device tree for the Kontron KSwitch D10 MMT
+ */
+
+/dts-v1/;
+#include "lan966x.dtsi"
+#include "dt-bindings/phy/phy-lan966x-serdes.h"
+
+/ {
+	aliases {
+		serial0 = &usart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-restart {
+		compatible = "gpio-restart";
+		pinctrl-0 = <&reset_pins>;
+		pinctrl-names = "default";
+		gpios = <&gpio 56 GPIO_ACTIVE_LOW>;
+		priority = <200>;
+	};
+};
+
+&flx0 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+	status = "okay";
+
+	usart0: serial@200 {
+		pinctrl-0 = <&usart0_pins>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+};
+
+&flx3 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
+	status = "okay";
+
+	spi3: spi@400 {
+		pinctrl-0 = <&fc3_b_pins>, <&spi3_cs_pins>;
+		pinctrl-names = "default";
+		status = "okay";
+		cs-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&gpio {
+	pinctrl-0 = <&phy_int_pins>;
+	pinctrl-names = "default";
+
+	fc3_b_pins: fc3-b-pins {
+		/* SCK, MISO, MOSI */
+		pins = "GPIO_51", "GPIO_52", "GPIO_53";
+		function = "fc3_b";
+	};
+
+	miim_c_pins: miim-c-pins {
+		/* MDC, MDIO */
+		pins = "GPIO_59", "GPIO_60";
+		function = "miim_c";
+	};
+
+	phy_int_pins: phy-int-pins {
+		/* PHY_INT# */
+		pins = "GPIO_24";
+		function = "gpio";
+	};
+
+	reset_pins: reset-pins {
+		/* SYS_RST# */
+		pins = "GPIO_56";
+		function = "gpio";
+	};
+
+	sgpio_a_pins: sgpio-a-pins {
+		/* SCK, D0, D1 */
+		pins = "GPIO_32", "GPIO_33", "GPIO_34";
+		function = "sgpio_a";
+	};
+
+	sgpio_b_pins: sgpio-b-pins {
+		/* LD */
+		pins = "GPIO_64";
+		function = "sgpio_b";
+	};
+
+	spi3_cs_pins: spi3-cs-pins {
+		/* CS# */
+		pins = "GPIO_46";
+		function = "gpio";
+	};
+
+	usart0_pins: usart0-pins {
+		/* RXD, TXD */
+		pins = "GPIO_25", "GPIO_26";
+		function = "fc0_b";
+	};
+
+	usbs_a_pins: usbs-a-pins {
+		/* VBUS_DET */
+		pins = "GPIO_66";
+		function = "gpio";
+	};
+};
+
+&mdio0 {
+	pinctrl-0 = <&miim_c_pins>;
+	pinctrl-names = "default";
+	reset-gpios = <&gpio 29 GPIO_ACTIVE_LOW>;
+	clock-frequency = <2500000>;
+	status = "okay";
+
+	phy4: ethernet-phy@5 {
+		reg = <5>;
+		interrupts-extended = <&gpio 24 IRQ_TYPE_LEVEL_LOW>;
+		coma-mode-gpios = <&gpio 37 GPIO_OPEN_DRAIN>;
+	};
+
+	phy5: ethernet-phy@6 {
+		reg = <6>;
+		interrupts-extended = <&gpio 24 IRQ_TYPE_LEVEL_LOW>;
+		coma-mode-gpios = <&gpio 37 GPIO_OPEN_DRAIN>;
+	};
+
+	phy6: ethernet-phy@7 {
+		reg = <7>;
+		interrupts-extended = <&gpio 24 IRQ_TYPE_LEVEL_LOW>;
+		coma-mode-gpios = <&gpio 37 GPIO_OPEN_DRAIN>;
+	};
+
+	phy7: ethernet-phy@8 {
+		reg = <8>;
+		interrupts-extended = <&gpio 24 IRQ_TYPE_LEVEL_LOW>;
+		coma-mode-gpios = <&gpio 37 GPIO_OPEN_DRAIN>;
+	};
+};
+
+&mdio1 {
+	status = "okay";
+};
+
+&phy0 {
+	status = "okay";
+};
+
+&phy1 {
+	status = "okay";
+};
+
+&port0 {
+	phys = <&serdes 0 CU(0)>;
+	phy-handle = <&phy0>;
+	phy-mode = "gmii";
+	status = "okay";
+};
+
+&port1 {
+	phys = <&serdes 1 CU(1)>;
+	phy-handle = <&phy1>;
+	phy-mode = "gmii";
+	status = "okay";
+};
+
+&port4 {
+	phys = <&serdes 4 SERDES6G(2)>;
+	phy-handle = <&phy4>;
+	phy-mode = "qsgmii";
+	status = "okay";
+};
+
+&port5 {
+	phys = <&serdes 5 SERDES6G(2)>;
+	phy-handle = <&phy5>;
+	phy-mode = "qsgmii";
+	status = "okay";
+};
+
+&port6 {
+	phys = <&serdes 6 SERDES6G(2)>;
+	phy-handle = <&phy6>;
+	phy-mode = "qsgmii";
+	status = "okay";
+};
+
+&port7 {
+	phys = <&serdes 7 SERDES6G(2)>;
+	phy-handle = <&phy7>;
+	phy-mode = "qsgmii";
+	status = "okay";
+};
+
+&serdes {
+	status = "okay";
+};
+
+&sgpio {
+	pinctrl-0 = <&sgpio_a_pins>, <&sgpio_b_pins>;
+	pinctrl-names = "default";
+	bus-frequency = <8000000>;
+	/* arbitrary range because all GPIOs are in software mode */
+	microchip,sgpio-port-ranges = <0 11>;
+	status = "okay";
+
+	sgpio_in: gpio@0 {
+		ngpios = <128>;
+	};
+
+	sgpio_out: gpio@1 {
+		ngpios = <128>;
+	};
+};
+
+&switch {
+	status = "okay";
+};
+
+&udc {
+	pinctrl-0 = <&usbs_a_pins>;
+	pinctrl-names = "default";
+	atmel,vbus-gpio = <&gpio 66 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/microchip/lan966x-pcb8290.dts b/arch/arm/boot/dts/microchip/lan966x-pcb8290.dts
new file mode 100644
index 000000000000..3b7577e48b46
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/lan966x-pcb8290.dts
@@ -0,0 +1,195 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * lan966x-pcb8290.dts - Device Tree file for LAN966X-PCB8290 board
+ *
+ * Copyright (C) 2022 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Horatiu Vultur <horatiu.vultur@microchip.com>
+ */
+/dts-v1/;
+#include "lan966x.dtsi"
+#include "dt-bindings/phy/phy-lan966x-serdes.h"
+
+/ {
+	model = "Microchip EVB LAN9668";
+	compatible = "microchip,lan9668-pcb8290", "microchip,lan9668", "microchip,lan966";
+
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&gpio 56 GPIO_ACTIVE_LOW>;
+		priority = <200>;
+	};
+};
+
+&aes {
+	status = "disabled"; /* Reserved by secure OS */
+};
+
+&gpio {
+	miim_a_pins: mdio-pins {
+		/* MDC, MDIO */
+		pins = "GPIO_28", "GPIO_29";
+		function = "miim_a";
+	};
+
+	pps_out_pins: pps-out-pins {
+		/* 1pps output */
+		pins = "GPIO_38";
+		function = "ptpsync_3";
+	};
+
+	ptp_ext_pins: ptp-ext-pins {
+		/* 1pps input */
+		pins = "GPIO_35";
+		function = "ptpsync_0";
+	};
+
+	udc_pins: ucd-pins {
+		/* VBUS_DET B */
+		pins = "GPIO_8";
+		function = "usb_slave_b";
+	};
+};
+
+&mdio0 {
+	pinctrl-0 = <&miim_a_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	ext_phy0: ethernet-phy@7 {
+		reg = <7>;
+		interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+		coma-mode-gpios = <&gpio 60 GPIO_OPEN_DRAIN>;
+	};
+
+	ext_phy1: ethernet-phy@8 {
+		reg = <8>;
+		interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+		coma-mode-gpios = <&gpio 60 GPIO_OPEN_DRAIN>;
+	};
+
+	ext_phy2: ethernet-phy@9 {
+		reg = <9>;
+		interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+		coma-mode-gpios = <&gpio 60 GPIO_OPEN_DRAIN>;
+	};
+
+	ext_phy3: ethernet-phy@10 {
+		reg = <10>;
+		interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+		coma-mode-gpios = <&gpio 60 GPIO_OPEN_DRAIN>;
+	};
+
+	ext_phy4: ethernet-phy@15 {
+		reg = <15>;
+		interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+		coma-mode-gpios = <&gpio 60 GPIO_OPEN_DRAIN>;
+	};
+
+	ext_phy5: ethernet-phy@16 {
+		reg = <16>;
+		interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+		coma-mode-gpios = <&gpio 60 GPIO_OPEN_DRAIN>;
+	};
+
+	ext_phy6: ethernet-phy@17 {
+		reg = <17>;
+		interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+		coma-mode-gpios = <&gpio 60 GPIO_OPEN_DRAIN>;
+	};
+
+	ext_phy7: ethernet-phy@18 {
+		reg = <18>;
+		interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio>;
+		coma-mode-gpios = <&gpio 60 GPIO_OPEN_DRAIN>;
+	};
+};
+
+&port0 {
+	reg = <2>;
+	phy-handle = <&ext_phy2>;
+	phy-mode = "qsgmii";
+	phys = <&serdes 0 SERDES6G(1)>;
+	status = "okay";
+};
+
+&port1 {
+	reg = <3>;
+	phy-handle = <&ext_phy3>;
+	phy-mode = "qsgmii";
+	phys = <&serdes 1 SERDES6G(1)>;
+	status = "okay";
+};
+
+&port2 {
+	reg = <0>;
+	phy-handle = <&ext_phy0>;
+	phy-mode = "qsgmii";
+	phys = <&serdes 2 SERDES6G(1)>;
+	status = "okay";
+};
+
+&port3 {
+	reg = <1>;
+	phy-handle = <&ext_phy1>;
+	phy-mode = "qsgmii";
+	phys = <&serdes 3 SERDES6G(1)>;
+	status = "okay";
+};
+
+&port4 {
+	reg = <6>;
+	phy-handle = <&ext_phy6>;
+	phy-mode = "qsgmii";
+	phys = <&serdes 4 SERDES6G(2)>;
+	status = "okay";
+};
+
+&port5 {
+	reg = <7>;
+	phy-handle = <&ext_phy7>;
+	phy-mode = "qsgmii";
+	phys = <&serdes 5 SERDES6G(2)>;
+	status = "okay";
+};
+
+&port6 {
+	reg = <4>;
+	phy-handle = <&ext_phy4>;
+	phy-mode = "qsgmii";
+	phys = <&serdes 6 SERDES6G(2)>;
+	status = "okay";
+};
+
+&port7 {
+	reg = <5>;
+	phy-handle = <&ext_phy5>;
+	phy-mode = "qsgmii";
+	phys = <&serdes 7 SERDES6G(2)>;
+	status = "okay";
+};
+
+&serdes {
+	status = "okay";
+};
+
+&switch {
+	pinctrl-0 = <&pps_out_pins>, <&ptp_ext_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&udc {
+	pinctrl-0 = <&udc_pins>;
+	pinctrl-names = "default";
+	atmel,vbus-gpio = <&gpio 8 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/microchip/lan966x-pcb8291.dts b/arch/arm/boot/dts/microchip/lan966x-pcb8291.dts
new file mode 100644
index 000000000000..3a3d76af8612
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/lan966x-pcb8291.dts
@@ -0,0 +1,147 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * lan966x_pcb8291.dts - Device Tree file for PCB8291
+ */
+/dts-v1/;
+#include "lan966x.dtsi"
+#include "dt-bindings/phy/phy-lan966x-serdes.h"
+
+/ {
+	model = "Microchip EVB - LAN9662";
+	compatible = "microchip,lan9662-pcb8291", "microchip,lan9662", "microchip,lan966";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	aliases {
+		serial0 = &usart3;
+	};
+
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&gpio 56 GPIO_ACTIVE_LOW>;
+		priority = <200>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-s0-blue {
+			label = "s0:blue";
+			gpios = <&sgpio_out 2 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-s0-green {
+			label = "s0:green";
+			gpios = <&sgpio_out 2 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-s1-blue {
+			label = "s1:blue";
+			gpios = <&sgpio_out 3 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-s1-green {
+			label = "s1:green";
+			gpios = <&sgpio_out 3 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+};
+
+&aes {
+	status = "disabled"; /* Reserved by secure OS */
+};
+
+&gpio {
+	fc3_b_pins: fc3-b-pins {
+		/* RX, TX */
+		pins = "GPIO_52", "GPIO_53";
+		function = "fc3_b";
+	};
+
+	can0_b_pins:  can0-b-pins {
+		/* RX, TX */
+		pins = "GPIO_35", "GPIO_36";
+		function = "can0_b";
+	};
+
+	sgpio_a_pins: sgpio-a-pins {
+		/* SCK, D0, D1, LD */
+		pins = "GPIO_32", "GPIO_33", "GPIO_34", "GPIO_35";
+		function = "sgpio_a";
+	};
+};
+
+&can0 {
+	pinctrl-0 = <&can0_b_pins>;
+	pinctrl-names = "default";
+	status = "disabled"; /* Conflict with switch */
+};
+
+&flx3 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+	status = "okay";
+
+	usart3: serial@200 {
+		pinctrl-0 = <&fc3_b_pins>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+};
+
+&mdio1 {
+	status = "okay";
+};
+
+&phy0 {
+	status = "okay";
+};
+
+&phy1 {
+	status = "okay";
+};
+
+&port0 {
+	phy-handle = <&phy0>;
+	phy-mode = "gmii";
+	phys = <&serdes 0 CU(0)>;
+	status = "okay";
+};
+
+&port1 {
+	phy-handle = <&phy1>;
+	phy-mode = "gmii";
+	phys = <&serdes 1 CU(1)>;
+	status = "okay";
+};
+
+&serdes {
+	status = "okay";
+};
+
+&sgpio {
+	pinctrl-0 = <&sgpio_a_pins>;
+	pinctrl-names = "default";
+	microchip,sgpio-port-ranges = <0 3>, <8 11>;
+	status = "okay";
+
+	gpio@0 {
+		ngpios = <64>;
+	};
+	gpio@1 {
+		ngpios = <64>;
+	};
+};
+
+&switch {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/microchip/lan966x-pcb8309.dts b/arch/arm/boot/dts/microchip/lan966x-pcb8309.dts
new file mode 100644
index 000000000000..0cb505f79ba1
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/lan966x-pcb8309.dts
@@ -0,0 +1,230 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * lan966x_pcb8309.dts - Device Tree file for PCB8309
+ */
+/dts-v1/;
+#include "lan966x.dtsi"
+#include "dt-bindings/phy/phy-lan966x-serdes.h"
+
+/ {
+	model = "Microchip EVB - LAN9662";
+	compatible = "microchip,lan9662-pcb8309", "microchip,lan9662", "microchip,lan966";
+
+	aliases {
+		serial0 = &usart3;
+		i2c102 = &i2c102;
+		i2c103 = &i2c103;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&gpio 56 GPIO_ACTIVE_LOW>;
+		priority = <200>;
+	};
+
+	i2c-mux {
+		compatible = "i2c-mux";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		mux-controls = <&mux>;
+		i2c-parent = <&i2c4>;
+
+		i2c102: i2c-sfp@1 {
+			reg = <1>;
+		};
+
+		i2c103: i2c-sfp@2 {
+			reg = <2>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-s0-green {
+			label = "s0:green";
+			gpios = <&sgpio_out 2 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-s0-red {
+			label = "s0:red";
+			gpios = <&sgpio_out 2 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-s1-green {
+			label = "s1:green";
+			gpios = <&sgpio_out 3 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-s1-red {
+			label = "s1:red";
+			gpios = <&sgpio_out 3 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	mux: mux-controller {
+		compatible = "gpio-mux";
+		#mux-control-cells = <0>;
+
+		mux-gpios = <&sgpio_out 11 0 GPIO_ACTIVE_HIGH>, /* p11b0 */
+			    <&sgpio_out 11 1 GPIO_ACTIVE_HIGH>; /* p11b1 */
+	};
+
+	sfp2: sfp2 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c102>;
+		tx-disable-gpios = <&sgpio_out 10 0 GPIO_ACTIVE_LOW>;
+		los-gpios = <&sgpio_in  2 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in  2 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in  1 0 GPIO_ACTIVE_HIGH>;
+	};
+
+	sfp3: sfp3 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c103>;
+		tx-disable-gpios = <&sgpio_out 10 1 GPIO_ACTIVE_LOW>;
+		los-gpios = <&sgpio_in  3 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in  3 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in  1 1 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&aes {
+	status = "disabled"; /* Reserved by secure OS */
+};
+
+&flx3 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+	status = "okay";
+
+	usart3: serial@200 {
+		pinctrl-0 = <&fc3_b_pins>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+};
+
+&flx4 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+
+	i2c4: i2c@600 {
+		compatible = "microchip,sam9x60-i2c";
+		reg = <0x600 0x200>;
+		interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&nic_clk>;
+		pinctrl-0 = <&fc4_b_pins>;
+		pinctrl-names = "default";
+		i2c-analog-filter;
+		i2c-digital-filter;
+		i2c-digital-filter-width-ns = <35>;
+		i2c-sda-hold-time-ns = <1500>;
+		status = "okay";
+	};
+};
+
+&gpio {
+	fc3_b_pins: fc3-b-pins {
+		/* RXD, TXD */
+		pins = "GPIO_52", "GPIO_53";
+		function = "fc3_b";
+	};
+
+	fc4_b_pins: fc4-b-pins {
+		/* SCL, SDA */
+		pins = "GPIO_57", "GPIO_58";
+		function = "fc4_b";
+	};
+
+	pps_out_pins: pps-out-pins {
+		/* 1pps output */
+		pins = "GPIO_38";
+		function = "ptpsync_3";
+	};
+
+	ptp_ext_pins: ptp-ext-pins {
+		/* 1pps input */
+		pins = "GPIO_39";
+		function = "ptpsync_4";
+	};
+
+	sgpio_a_pins: sgpio-a-pins {
+		/* SCK, D0, D1, LD */
+		pins = "GPIO_32", "GPIO_33", "GPIO_34", "GPIO_35";
+		function = "sgpio_a";
+	};
+};
+
+&mdio1 {
+	status = "okay";
+};
+
+&phy0 {
+	status = "okay";
+};
+
+&phy1 {
+	status = "okay";
+};
+
+&port0 {
+	phy-handle = <&phy0>;
+	phy-mode = "gmii";
+	phys = <&serdes 0 CU(0)>;
+	status = "okay";
+};
+
+&port1 {
+	phy-handle = <&phy1>;
+	phy-mode = "gmii";
+	phys = <&serdes 1 CU(1)>;
+	status = "okay";
+};
+
+&port2 {
+	sfp = <&sfp2>;
+	managed = "in-band-status";
+	phy-mode = "sgmii";
+	phys = <&serdes 2 SERDES6G(0)>;
+	status = "okay";
+};
+
+&port3 {
+	sfp = <&sfp3>;
+	managed = "in-band-status";
+	phy-mode = "sgmii";
+	phys = <&serdes 3 SERDES6G(1)>;
+	status = "okay";
+};
+
+&serdes {
+	status = "okay";
+};
+
+&sgpio {
+	pinctrl-0 = <&sgpio_a_pins>;
+	pinctrl-names = "default";
+	microchip,sgpio-port-ranges = <0 3>, <8 11>;
+	status = "okay";
+
+	gpio@0 {
+		ngpios = <64>;
+	};
+	gpio@1 {
+		ngpios = <64>;
+	};
+};
+
+&switch {
+	pinctrl-0 = <&pps_out_pins>, <&ptp_ext_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/microchip/lan966x.dtsi b/arch/arm/boot/dts/microchip/lan966x.dtsi
new file mode 100644
index 000000000000..05b73f7cf0c7
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/lan966x.dtsi
@@ -0,0 +1,615 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * lan966x.dtsi - Device Tree Include file for Microchip LAN966 family SoC
+ *
+ * Copyright (C) 2021 Microchip Technology, Inc. and its subsidiaries
+ *
+ * Author: Kavyasree Kotagiri <kavyasree.kotagiri@microchip.com>
+ *
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/dma/at91.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/microchip,lan966x.h>
+
+/ {
+	model = "Microchip LAN966 family SoC";
+	compatible = "microchip,lan966";
+	interrupt-parent = <&gic>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			clock-frequency = <600000000>;
+			reg = <0x0>;
+		};
+	};
+
+	clocks {
+		sys_clk: sys_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <165625000>;
+		};
+
+		cpu_clk: cpu_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <600000000>;
+		};
+
+		ddr_clk: ddr_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <300000000>;
+		};
+
+		nic_clk: nic_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+	};
+
+	clks: clock-controller@e00c00a8 {
+		compatible = "microchip,lan966x-gck";
+		#clock-cells = <1>;
+		clocks = <&cpu_clk>, <&ddr_clk>, <&sys_clk>;
+		clock-names = "cpu", "ddr", "sys";
+		reg = <0xe00c00a8 0x38>, <0xe00c02cc 0x4>;
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
+		clock-frequency = <37500000>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		udc: usb@200000 {
+			compatible = "microchip,lan9662-udc",
+				     "atmel,sama5d3-udc";
+			reg = <0x00200000 0x80000>,
+			      <0xe0808000 0x400>;
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clks GCK_GATE_UDPHS>, <&nic_clk>;
+			clock-names = "pclk", "hclk";
+			status = "disabled";
+		};
+
+		switch: switch@e0000000 {
+			compatible = "microchip,lan966x-switch";
+			reg = <0xe0000000 0x0100000>,
+			      <0xe2000000 0x0800000>;
+			reg-names = "cpu", "gcb";
+			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "xtr", "fdma", "ana", "ptp",
+					  "ptp-ext";
+			resets = <&reset 0>;
+			reset-names = "switch";
+			status = "disabled";
+
+			ethernet-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port0: port@0 {
+					reg = <0>;
+					status = "disabled";
+				};
+
+				port1: port@1 {
+					reg = <1>;
+					status = "disabled";
+				};
+
+				port2: port@2 {
+					reg = <2>;
+					status = "disabled";
+				};
+
+				port3: port@3 {
+					reg = <3>;
+					status = "disabled";
+				};
+
+				port4: port@4 {
+					reg = <4>;
+					status = "disabled";
+				};
+
+				port5: port@5 {
+					reg = <5>;
+					status = "disabled";
+				};
+
+				port6: port@6 {
+					reg = <6>;
+					status = "disabled";
+				};
+
+				port7: port@7 {
+					reg = <7>;
+					status = "disabled";
+				};
+			};
+		};
+
+		otp: otp@e0021000 {
+			compatible = "microchip,lan9668-otpc", "microchip,lan9662-otpc";
+			reg = <0xe0021000 0x300>;
+		};
+
+		flx0: flexcom@e0040000 {
+			compatible = "atmel,sama5d2-flexcom";
+			reg = <0xe0040000 0x100>;
+			clocks = <&clks GCK_ID_FLEXCOM0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xe0040000 0x800>;
+			status = "disabled";
+
+			usart0: serial@200 {
+				compatible = "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(3)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(2)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "usart";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+
+			spi0: spi@400 {
+				compatible = "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(3)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(2)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "spi_clk";
+				atmel,fifo-size = <32>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c0: i2c@600 {
+				compatible = "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(3)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(2)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		flx1: flexcom@e0044000 {
+			compatible = "atmel,sama5d2-flexcom";
+			reg = <0xe0044000 0x100>;
+			clocks = <&clks GCK_ID_FLEXCOM1>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xe0044000 0x800>;
+			status = "disabled";
+
+			usart1: serial@200 {
+				compatible = "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(5)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(4)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "usart";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+
+			spi1: spi@400 {
+				compatible = "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(5)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(4)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "spi_clk";
+				atmel,fifo-size = <32>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@600 {
+				compatible = "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(5)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(4)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		trng: rng@e0048000 {
+			compatible = "atmel,at91sam9g45-trng";
+			reg = <0xe0048000 0x100>;
+			clocks = <&nic_clk>;
+		};
+
+		aes: crypto@e004c000 {
+			compatible = "atmel,at91sam9g46-aes";
+			reg = <0xe004c000 0x100>;
+			interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(12)>,
+			       <&dma0 AT91_XDMAC_DT_PERID(13)>;
+			dma-names = "tx", "rx";
+			clocks = <&nic_clk>;
+			clock-names = "aes_clk";
+		};
+
+		flx2: flexcom@e0060000 {
+			compatible = "atmel,sama5d2-flexcom";
+			reg = <0xe0060000 0x100>;
+			clocks = <&clks GCK_ID_FLEXCOM2>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xe0060000 0x800>;
+			status = "disabled";
+
+			usart2: serial@200 {
+				compatible = "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(7)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(6)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "usart";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+
+			spi2: spi@400 {
+				compatible = "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(7)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(6)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "spi_clk";
+				atmel,fifo-size = <32>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c2: i2c@600 {
+				compatible = "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(7)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(6)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		flx3: flexcom@e0064000 {
+			compatible = "atmel,sama5d2-flexcom";
+			reg = <0xe0064000 0x100>;
+			clocks = <&clks GCK_ID_FLEXCOM3>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xe0064000 0x800>;
+			status = "disabled";
+
+			usart3: serial@200 {
+				compatible = "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(9)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(8)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "usart";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+
+			spi3: spi@400 {
+				compatible = "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(9)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(8)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "spi_clk";
+				atmel,fifo-size = <32>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c3: i2c@600 {
+				compatible = "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(9)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(8)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		dma0: dma-controller@e0068000 {
+			compatible = "microchip,sama7g5-dma";
+			reg = <0xe0068000 0x1000>;
+			interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			clocks = <&nic_clk>;
+			clock-names = "dma_clk";
+		};
+
+		sha: crypto@e006c000 {
+			compatible = "atmel,at91sam9g46-sha";
+			reg = <0xe006c000 0xec>;
+			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(14)>;
+			dma-names = "tx";
+			clocks = <&nic_clk>;
+			clock-names = "sha_clk";
+		};
+
+		flx4: flexcom@e0070000 {
+			compatible = "atmel,sama5d2-flexcom";
+			reg = <0xe0070000 0x100>;
+			clocks = <&clks GCK_ID_FLEXCOM4>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xe0070000 0x800>;
+			status = "disabled";
+
+			usart4: serial@200 {
+				compatible = "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(11)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(10)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "usart";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+
+			spi4: spi@400 {
+				compatible = "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(11)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(10)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "spi_clk";
+				atmel,fifo-size = <32>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c4: i2c@600 {
+				compatible = "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(11)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(10)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		timer0: timer@e008c000 {
+			compatible = "snps,dw-apb-timer";
+			reg = <0xe008c000 0x400>;
+			clocks = <&nic_clk>;
+			clock-names = "timer";
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		watchdog: watchdog@e0090000 {
+			compatible = "snps,dw-wdt";
+			reg = <0xe0090000 0x1000>;
+			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&nic_clk>;
+			status = "disabled";
+		};
+
+		cpu_ctrl: syscon@e00c0000 {
+			compatible = "microchip,lan966x-cpu-syscon", "syscon";
+			reg = <0xe00c0000 0x350>;
+		};
+
+		can0: can@e081c000 {
+			compatible = "bosch,m_can";
+			reg = <0xe081c000 0xfc>, <0x00100000 0x4000>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&clks GCK_ID_MCAN0>, <&clks GCK_ID_MCAN0>;
+			clock-names = "hclk", "cclk";
+			assigned-clocks = <&clks GCK_ID_MCAN0>;
+			assigned-clock-rates = <40000000>;
+			bosch,mram-cfg = <0x0 0 0 64 0 0 32 32>;
+			status = "disabled";
+		};
+
+		can1: can@e0820000 {
+			compatible = "bosch,m_can";
+			reg = <0xe0820000 0xfc>, <0x00100000 0x8000>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&clks GCK_ID_MCAN1>, <&clks GCK_ID_MCAN1>;
+			clock-names = "hclk", "cclk";
+			assigned-clocks = <&clks GCK_ID_MCAN1>;
+			assigned-clock-rates = <40000000>;
+			bosch,mram-cfg = <0x4000 0 0 64 0 0 32 32>;
+			status = "disabled";
+		};
+
+		reset: reset-controller@e200400c {
+			compatible = "microchip,lan966x-switch-reset";
+			reg = <0xe200400c 0x4>;
+			reg-names = "gcb";
+			#reset-cells = <1>;
+			cpu-syscon = <&cpu_ctrl>;
+		};
+
+		gpio: pinctrl@e2004064 {
+			compatible = "microchip,lan966x-pinctrl";
+			reg = <0xe2004064 0xb4>,
+			    <0xe2010024 0x138>;
+			resets = <&reset 0>;
+			reset-names = "switch";
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&gpio 0 0 78>;
+			interrupt-controller;
+			interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+			#interrupt-cells = <2>;
+		};
+
+		mdio0: mdio@e2004118 {
+			compatible = "microchip,lan966x-miim";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0xe2004118 0x24>;
+			clocks = <&sys_clk>;
+			status = "disabled";
+		};
+
+		mdio1: mdio@e200413c {
+			compatible = "microchip,lan966x-miim";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0xe200413c 0x24>,
+			      <0xe2010020 0x4>;
+			clocks = <&sys_clk>;
+			status = "disabled";
+
+			phy0: ethernet-phy@1 {
+				reg = <1>;
+				interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+
+			phy1: ethernet-phy@2 {
+				reg = <2>;
+				interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+		};
+
+		sgpio: gpio@e2004190 {
+			compatible = "microchip,sparx5-sgpio";
+			reg = <0xe2004190 0x118>;
+			clocks = <&sys_clk>;
+			resets = <&reset 0>;
+			reset-names = "switch";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sgpio_in: gpio@0 {
+				compatible = "microchip,sparx5-sgpio-bank";
+				reg = <0>;
+				gpio-controller;
+				#gpio-cells = <3>;
+				interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-controller;
+				#interrupt-cells = <3>;
+			};
+
+			sgpio_out: gpio@1 {
+				compatible = "microchip,sparx5-sgpio-bank";
+				reg = <1>;
+				gpio-controller;
+				#gpio-cells = <3>;
+			};
+		};
+
+		hwmon: hwmon@e2010180 {
+			compatible = "microchip,lan9668-hwmon";
+			reg = <0xe2010180 0xc>,
+			      <0xe20042a8 0xc>;
+			reg-names = "pvt", "fan";
+			clocks = <&sys_clk>;
+		};
+
+		serdes: serdes@e202c000 {
+			compatible = "microchip,lan966x-serdes";
+			reg = <0xe202c000 0x9c>,
+			      <0xe2004010 0x4>;
+			#phy-cells = <2>;
+			status = "disabled";
+		};
+
+		gic: interrupt-controller@e8c11000 {
+			compatible = "arm,gic-400", "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			reg = <0xe8c11000 0x1000>,
+			      <0xe8c12000 0x2000>,
+			      <0xe8c14000 0x2000>,
+			      <0xe8c16000 0x2000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/mpa1600.dts b/arch/arm/boot/dts/microchip/mpa1600.dts
index 005c2758e229..2a97e2c0b894 100644
--- a/arch/arm/boot/dts/mpa1600.dts
+++ b/arch/arm/boot/dts/microchip/mpa1600.dts
@@ -57,7 +57,7 @@
 			};
 		};
 
-		usb0: ohci@300000 {
+		usb0: usb@300000 {
 			num-ports = <1>;
 			status = "okay";
 		};
diff --git a/arch/arm/boot/dts/pm9g45.dts b/arch/arm/boot/dts/microchip/pm9g45.dts
index c349fd3758a6..2258e62f5864 100644
--- a/arch/arm/boot/dts/pm9g45.dts
+++ b/arch/arm/boot/dts/microchip/pm9g45.dts
@@ -139,12 +139,12 @@
 			};
 		};
 
-		usb0: ohci@700000 {
+		usb0: usb@700000 {
 			status = "okay";
 			num-ports = <2>;
 		};
 
-		usb1: ehci@800000 {
+		usb1: usb@800000 {
 			status = "okay";
 		};
 	};
diff --git a/arch/arm/boot/dts/microchip/sam9x60.dtsi b/arch/arm/boot/dts/microchip/sam9x60.dtsi
new file mode 100644
index 000000000000..b075865e6a76
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/sam9x60.dtsi
@@ -0,0 +1,1403 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * sam9x60.dtsi - Device Tree Include file for Microchip SAM9X60 SoC
+ *
+ * Copyright (C) 2019 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Sandeep Sheriker M <sandeepsheriker.mallikarjun@microchip.com>
+ */
+
+#include <dt-bindings/dma/at91.h>
+#include <dt-bindings/pinctrl/at91.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
+#include <dt-bindings/mfd/atmel-flexcom.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	model = "Microchip SAM9X60 SoC";
+	compatible = "microchip,sam9x60";
+	interrupt-parent = <&aic>;
+
+	aliases {
+		serial0 = &dbgu;
+		gpio0 = &pioA;
+		gpio1 = &pioB;
+		gpio2 = &pioC;
+		gpio3 = &pioD;
+		tcb0 = &tcb0;
+		tcb1 = &tcb1;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "arm,arm926ej-s";
+			device_type = "cpu";
+			reg = <0>;
+		};
+	};
+
+	memory@20000000 {
+		device_type = "memory";
+		reg = <0x20000000 0x10000000>;
+	};
+
+	clocks {
+		slow_xtal: slow_xtal {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+		};
+
+		main_xtal: main_xtal {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+		};
+	};
+
+	sram: sram@300000 {
+		compatible = "mmio-sram";
+		reg = <0x00300000 0x100000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x00300000 0x100000>;
+	};
+
+	ahb {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		usb0: gadget@500000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "microchip,sam9x60-udc";
+			reg = <0x00500000 0x100000
+				0xf803c000 0x400>;
+			interrupts = <23 IRQ_TYPE_LEVEL_HIGH 2>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 23>, <&pmc PMC_TYPE_CORE PMC_UTMI>;
+			clock-names = "pclk", "hclk";
+			assigned-clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>;
+			assigned-clock-rates = <480000000>;
+			status = "disabled";
+		};
+
+		usb1: usb@600000 {
+			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
+			reg = <0x00600000 0x100000>;
+			interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 22>, <&pmc PMC_TYPE_PERIPHERAL 22>, <&pmc PMC_TYPE_SYSTEM 6>;
+			clock-names = "ohci_clk", "hclk", "uhpck";
+			status = "disabled";
+		};
+
+		usb2: usb@700000 {
+			compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
+			reg = <0x00700000 0x100000>;
+			interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
+			clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_PERIPHERAL 22>;
+			clock-names = "usb_clk", "ehci_clk";
+			assigned-clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>;
+			assigned-clock-rates = <480000000>;
+			status = "disabled";
+		};
+
+		ebi: ebi@10000000 {
+			compatible = "microchip,sam9x60-ebi";
+			#address-cells = <2>;
+			#size-cells = <1>;
+			atmel,smc = <&smc>;
+			microchip,sfr = <&sfr>;
+			reg = <0x10000000 0x60000000>;
+			ranges = <0x0 0x0 0x10000000 0x10000000
+				  0x1 0x0 0x20000000 0x10000000
+				  0x2 0x0 0x30000000 0x10000000
+				  0x3 0x0 0x40000000 0x10000000
+				  0x4 0x0 0x50000000 0x10000000
+				  0x5 0x0 0x60000000 0x10000000>;
+			clocks = <&pmc PMC_TYPE_CORE PMC_MCK>;
+			status = "disabled";
+
+			nand_controller: nand-controller {
+				compatible = "microchip,sam9x60-nand-controller";
+				ecc-engine = <&pmecc>;
+				#address-cells = <2>;
+				#size-cells = <1>;
+				ranges;
+				status = "disabled";
+			};
+		};
+
+		sdmmc0: sdio-host@80000000 {
+			compatible = "microchip,sam9x60-sdhci";
+			reg = <0x80000000 0x300>;
+			interrupts = <12 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 12>, <&pmc PMC_TYPE_GCK 12>;
+			clock-names = "hclock", "multclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 12>;
+			assigned-clock-rates = <100000000>;
+			status = "disabled";
+		};
+
+		sdmmc1: sdio-host@90000000 {
+			compatible = "microchip,sam9x60-sdhci";
+			reg = <0x90000000 0x300>;
+			interrupts = <26 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 26>, <&pmc PMC_TYPE_GCK 26>;
+			clock-names = "hclock", "multclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 26>;
+			assigned-clock-rates = <100000000>;
+			status = "disabled";
+		};
+
+		apb {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			flx4: flexcom@f0000000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xf0000000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf0000000 0x800>;
+				status = "disabled";
+
+				uart4: serial@200 {
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(8))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(9))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+					clock-names = "usart";
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				spi4: spi@400 {
+					compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(8))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(9))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c4: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(8))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(9))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx5: flexcom@f0004000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xf0004000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf0004000 0x800>;
+				status = "disabled";
+
+				uart5: serial@200 {
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+					interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(10))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(11))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				spi5: spi@400 {
+					compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(10))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(11))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c5: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(10))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(11))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			dma0: dma-controller@f0008000 {
+				compatible = "microchip,sam9x60-dma", "atmel,sama5d4-dma";
+				reg = <0xf0008000 0x1000>;
+				interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
+				#dma-cells = <1>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 20>;
+				clock-names = "dma_clk";
+			};
+
+			ssc: ssc@f0010000 {
+				compatible = "atmel,at91sam9g45-ssc";
+				reg = <0xf0010000 0x4000>;
+				interrupts = <28 IRQ_TYPE_LEVEL_HIGH 5>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(38))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(39))>;
+				dma-names = "tx", "rx";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 28>;
+				clock-names = "pclk";
+				status = "disabled";
+			};
+
+			qspi: spi@f0014000 {
+				compatible = "microchip,sam9x60-qspi";
+				reg = <0xf0014000 0x100>, <0x70000000 0x10000000>;
+				reg-names = "qspi_base", "qspi_mmap";
+				interrupts = <35 IRQ_TYPE_LEVEL_HIGH 7>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(26))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(27))>;
+				dma-names = "tx", "rx";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 35>, <&pmc PMC_TYPE_SYSTEM 19>;
+				clock-names = "pclk", "qspick";
+				atmel,pmc = <&pmc>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2s: i2s@f001c000 {
+				compatible = "microchip,sam9x60-i2smcc";
+				reg = <0xf001c000 0x100>;
+				interrupts = <34 IRQ_TYPE_LEVEL_HIGH 7>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(36))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(37))>;
+				dma-names = "tx", "rx";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 34>, <&pmc PMC_TYPE_GCK 34>;
+				clock-names = "pclk", "gclk";
+				status = "disabled";
+			};
+
+			flx11: flexcom@f0020000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xf0020000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf0020000 0x800>;
+				status = "disabled";
+
+				uart11: serial@200 {
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(22))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(23))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
+					clock-names = "usart";
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c11: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(22))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(23))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx12: flexcom@f0024000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xf0024000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf0024000 0x800>;
+				status = "disabled";
+
+				uart12: serial@200 {
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(24))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(25))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
+					clock-names = "usart";
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c12: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(24))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(25))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			pit64b: timer@f0028000 {
+				compatible = "microchip,sam9x60-pit64b";
+				reg = <0xf0028000 0x100>;
+				interrupts = <37 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 37>, <&pmc PMC_TYPE_GCK 37>;
+				clock-names = "pclk", "gclk";
+			};
+
+			sha: crypto@f002c000 {
+				compatible = "atmel,at91sam9g46-sha";
+				reg = <0xf002c000 0x100>;
+				interrupts = <41 IRQ_TYPE_LEVEL_HIGH 0>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(34))>;
+				dma-names = "tx";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 41>;
+				clock-names = "sha_clk";
+			};
+
+			trng: rng@f0030000 {
+				compatible = "microchip,sam9x60-trng";
+				reg = <0xf0030000 0x100>;
+				interrupts = <38 IRQ_TYPE_LEVEL_HIGH 0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 38>;
+			};
+
+			aes: crypto@f0034000 {
+				compatible = "atmel,at91sam9g46-aes";
+				reg = <0xf0034000 0x100>;
+				interrupts = <39 IRQ_TYPE_LEVEL_HIGH 0>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(32))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(33))>;
+				dma-names = "tx", "rx";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 39>;
+				clock-names = "aes_clk";
+			};
+
+			tdes: crypto@f0038000 {
+				compatible = "atmel,at91sam9g46-tdes";
+				reg = <0xf0038000 0x100>;
+				interrupts = <40 IRQ_TYPE_LEVEL_HIGH 0>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(31))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(30))>;
+				dma-names = "tx", "rx";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 40>;
+				clock-names = "tdes_clk";
+			};
+
+			classd: classd@f003c000 {
+				compatible = "atmel,sama5d2-classd";
+				reg = <0xf003c000 0x100>;
+				interrupts = <42 IRQ_TYPE_LEVEL_HIGH 7>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(35))>;
+				dma-names = "tx";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 42>, <&pmc PMC_TYPE_GCK 42>;
+				clock-names = "pclk", "gclk";
+				status = "disabled";
+			};
+
+			can0: can@f8000000 {
+				compatible = "microchip,sam9x60-can", "atmel,at91sam9x5-can";
+				reg = <0xf8000000 0x300>;
+				interrupts = <29 IRQ_TYPE_LEVEL_HIGH 3>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 29>;
+				clock-names = "can_clk";
+				status = "disabled";
+			};
+
+			can1: can@f8004000 {
+				compatible = "microchip,sam9x60-can", "atmel,at91sam9x5-can";
+				reg = <0xf8004000 0x300>;
+				interrupts = <30 IRQ_TYPE_LEVEL_HIGH 3>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 30>;
+				clock-names = "can_clk";
+				status = "disabled";
+			};
+
+			tcb0: timer@f8008000 {
+				compatible = "microchip,sam9x60-tcb", "atmel,at91sam9x5-tcb", "simple-mfd", "syscon";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0xf8008000 0x100>;
+				interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 17>, <&clk32k 0>;
+				clock-names = "t0_clk", "slow_clk";
+			};
+
+			tcb1: timer@f800c000 {
+				compatible = "microchip,sam9x60-tcb", "atmel,at91sam9x5-tcb", "simple-mfd", "syscon";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0xf800c000 0x100>;
+				interrupts = <45 IRQ_TYPE_LEVEL_HIGH 0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 45>, <&clk32k 0>;
+				clock-names = "t0_clk", "slow_clk";
+			};
+
+			flx6: flexcom@f8010000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xf8010000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf8010000 0x800>;
+				status = "disabled";
+
+				uart6: serial@200 {
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(12))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(13))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+					clock-names = "usart";
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c6: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(12))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(13))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx7: flexcom@f8014000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xf8014000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf8014000 0x800>;
+				status = "disabled";
+
+				uart7: serial@200 {
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(14))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(15))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+					clock-names = "usart";
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c7: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(14))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(15))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx8: flexcom@f8018000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xf8018000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf8018000 0x800>;
+				status = "disabled";
+
+				uart8: serial@200 {
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(16))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(17))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+					clock-names = "usart";
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c8: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(16))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(17))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx0: flexcom@f801c000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xf801c000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf801c000 0x800>;
+				status = "disabled";
+
+				uart0: serial@200 {
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(0))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(1))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+					clock-names = "usart";
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				spi0: spi@400 {
+					compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(0))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(1))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c0: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(0))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(1))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx1: flexcom@f8020000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xf8020000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf8020000 0x800>;
+				status = "disabled";
+
+				uart1: serial@200 {
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(2))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(3))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+					clock-names = "usart";
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				spi1: spi@400 {
+					compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(2))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(3))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c1: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(2))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(3))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx2: flexcom@f8024000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xf8024000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf8024000 0x800>;
+				status = "disabled";
+
+				uart2: serial@200 {
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(4))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(5))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+					clock-names = "usart";
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				spi2: spi@400 {
+					compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(4))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(5))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c2: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(4))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(5))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx3: flexcom@f8028000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xf8028000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf8028000 0x800>;
+				status = "disabled";
+
+				uart3: serial@200 {
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(6))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(7))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+					clock-names = "usart";
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				spi3: spi@400 {
+					compatible = "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(6))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(7))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c3: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(6))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(7))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			macb0: ethernet@f802c000 {
+				compatible = "cdns,sam9x60-macb", "cdns,macb";
+				reg = <0xf802c000 0x1000>;
+				interrupts = <24 IRQ_TYPE_LEVEL_HIGH 3>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 24>, <&pmc PMC_TYPE_PERIPHERAL 24>;
+				clock-names = "hclk", "pclk";
+				status = "disabled";
+			};
+
+			macb1: ethernet@f8030000 {
+				compatible = "cdns,sam9x60-macb", "cdns,macb";
+				reg = <0xf8030000 0x1000>;
+				interrupts = <27 IRQ_TYPE_LEVEL_HIGH 3>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 27>, <&pmc PMC_TYPE_PERIPHERAL 27>;
+				clock-names = "hclk", "pclk";
+				status = "disabled";
+			};
+
+			pwm0: pwm@f8034000 {
+				compatible = "microchip,sam9x60-pwm";
+				reg = <0xf8034000 0x300>;
+				interrupts = <18 IRQ_TYPE_LEVEL_HIGH 4>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 18>;
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			hlcdc: hlcdc@f8038000 {
+				compatible = "microchip,sam9x60-hlcdc";
+				reg = <0xf8038000 0x4000>;
+				interrupts = <25 IRQ_TYPE_LEVEL_HIGH 0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 25>, <&pmc PMC_TYPE_GCK 25>, <&clk32k 1>;
+				clock-names = "periph_clk","sys_clk", "slow_clk";
+				assigned-clocks = <&pmc PMC_TYPE_GCK 25>;
+				assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_MCK>;
+				status = "disabled";
+
+				hlcdc-display-controller {
+					compatible = "atmel,hlcdc-display-controller";
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						#address-cells = <1>;
+						#size-cells = <0>;
+						reg = <0>;
+					};
+				};
+
+				hlcdc_pwm: hlcdc-pwm {
+					compatible = "atmel,hlcdc-pwm";
+					#pwm-cells = <3>;
+				};
+			};
+
+			flx9: flexcom@f8040000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xf8040000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf8040000 0x800>;
+				status = "disabled";
+
+				uart9: serial@200 {
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(18))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(19))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
+					clock-names = "usart";
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c9: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(18))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(19))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx10: flexcom@f8044000 {
+				compatible = "atmel,sama5d2-flexcom";
+				reg = <0xf8044000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf8044000 0x800>;
+				status = "disabled";
+
+				uart10: serial@200 {
+					compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(20))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(21))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
+					clock-names = "usart";
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c10: i2c@600 {
+					compatible = "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(20))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(21))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			isi: isi@f8048000 {
+				compatible = "microchip,sam9x60-isi", "atmel,at91sam9g45-isi";
+				reg = <0xf8048000 0x100>;
+				interrupts = <43 IRQ_TYPE_LEVEL_HIGH 5>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 43>;
+				clock-names = "isi_clk";
+				status = "disabled";
+				port {
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+			};
+
+			adc: adc@f804c000 {
+				compatible = "microchip,sam9x60-adc", "atmel,sama5d2-adc";
+				reg = <0xf804c000 0x100>;
+				interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
+				clock-names = "adc_clk";
+				dmas = <&dma0 (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | AT91_XDMAC_DT_PERID(40))>;
+				dma-names = "rx";
+				atmel,min-sample-rate-hz = <200000>;
+				atmel,max-sample-rate-hz = <20000000>;
+				atmel,startup-time-ms = <4>;
+				atmel,trigger-edge-type = <IRQ_TYPE_EDGE_RISING>;
+				#io-channel-cells = <1>;
+				status = "disabled";
+			};
+
+			sfr: sfr@f8050000 {
+				compatible = "microchip,sam9x60-sfr", "syscon";
+				reg = <0xf8050000 0x100>;
+			};
+
+			matrix: matrix@ffffde00 {
+				compatible = "microchip,sam9x60-matrix", "atmel,at91sam9x5-matrix", "syscon";
+				reg = <0xffffde00 0x200>;
+			};
+
+			pmecc: ecc-engine@ffffe000 {
+				compatible = "microchip,sam9x60-pmecc", "atmel,at91sam9g45-pmecc";
+				reg = <0xffffe000 0x300>,
+				      <0xffffe600 0x100>;
+			};
+
+			mpddrc: mpddrc@ffffe800 {
+				compatible = "microchip,sam9x60-ddramc", "atmel,sama5d3-ddramc";
+				reg = <0xffffe800 0x200>;
+				clocks = <&pmc PMC_TYPE_SYSTEM 2>, <&pmc PMC_TYPE_PERIPHERAL 49>;
+				clock-names = "ddrck", "mpddr";
+			};
+
+			smc: smc@ffffea00 {
+				compatible = "microchip,sam9x60-smc", "atmel,at91sam9260-smc", "syscon";
+				reg = <0xffffea00 0x100>;
+			};
+
+			aic: interrupt-controller@fffff100 {
+				compatible = "microchip,sam9x60-aic";
+				#interrupt-cells = <3>;
+				interrupt-controller;
+				reg = <0xfffff100 0x100>;
+				atmel,external-irqs = <31>;
+			};
+
+			dbgu: serial@fffff200 {
+				compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+				reg = <0xfffff200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				interrupts = <47 IRQ_TYPE_LEVEL_HIGH 7>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(28))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(29))>;
+				dma-names = "tx", "rx";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 47>;
+				clock-names = "usart";
+				status = "disabled";
+			};
+
+			pinctrl: pinctrl@fffff400 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "microchip,sam9x60-pinctrl", "simple-mfd";
+				ranges = <0xfffff400 0xfffff400 0x800>;
+
+				/* mux-mask corresponding to sam9x60 SoC in TFBGA228L package */
+				atmel,mux-mask = <
+						 /*	A	B	C	*/
+						 0xffffffff 0xffe03fff 0xef00019d	/* pioA */
+						 0x03ffffff 0x02fc7e7f 0x00780000	/* pioB */
+						 0xffffffff 0xffffffff 0xf83fffff	/* pioC */
+						 0x003fffff 0x003f8000 0x00000000	/* pioD */
+						 >;
+
+				pioA: gpio@fffff400 {
+					compatible = "microchip,sam9x60-gpio", "atmel,at91rm9200-gpio";
+					reg = <0xfffff400 0x200>;
+					interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
+					#gpio-cells = <2>;
+					gpio-controller;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 2>;
+				};
+
+				pioB: gpio@fffff600 {
+					compatible = "microchip,sam9x60-gpio", "atmel,at91rm9200-gpio";
+					reg = <0xfffff600 0x200>;
+					interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
+					#gpio-cells = <2>;
+					gpio-controller;
+					#gpio-lines = <26>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 3>;
+				};
+
+				pioC: gpio@fffff800 {
+					compatible = "microchip,sam9x60-gpio", "atmel,at91rm9200-gpio";
+					reg = <0xfffff800 0x200>;
+					interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>;
+					#gpio-cells = <2>;
+					gpio-controller;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 4>;
+				};
+
+				pioD: gpio@fffffa00 {
+					compatible = "microchip,sam9x60-gpio", "atmel,at91rm9200-gpio";
+					reg = <0xfffffa00 0x200>;
+					interrupts = <44 IRQ_TYPE_LEVEL_HIGH 1>;
+					#gpio-cells = <2>;
+					gpio-controller;
+					#gpio-lines = <22>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 44>;
+				};
+			};
+
+			pmc: clock-controller@fffffc00 {
+				compatible = "microchip,sam9x60-pmc", "syscon";
+				reg = <0xfffffc00 0x200>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+				#clock-cells = <2>;
+				clocks = <&clk32k 1>, <&clk32k 0>, <&main_xtal>;
+				clock-names = "td_slck", "md_slck", "main_xtal";
+			};
+
+			reset_controller: reset-controller@fffffe00 {
+				compatible = "microchip,sam9x60-rstc";
+				reg = <0xfffffe00 0x10>;
+				clocks = <&clk32k 0>;
+			};
+
+			shutdown_controller: poweroff@fffffe10 {
+				compatible = "microchip,sam9x60-shdwc";
+				reg = <0xfffffe10 0x10>;
+				clocks = <&clk32k 0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				atmel,wakeup-rtc-timer;
+				atmel,wakeup-rtt-timer;
+				status = "disabled";
+			};
+
+			rtt: rtc@fffffe20 {
+				compatible = "microchip,sam9x60-rtt", "atmel,at91sam9260-rtt";
+				reg = <0xfffffe20 0x20>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&clk32k 1>;
+			};
+
+			pit: timer@fffffe40 {
+				compatible = "atmel,at91sam9260-pit";
+				reg = <0xfffffe40 0x10>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_CORE PMC_MCK>;
+			};
+
+			clk32k: clock-controller@fffffe50 {
+				compatible = "microchip,sam9x60-sckc";
+				reg = <0xfffffe50 0x4>;
+				clocks = <&slow_xtal>;
+				#clock-cells = <1>;
+			};
+
+			gpbr: syscon@fffffe60 {
+				compatible = "microchip,sam9x60-gpbr", "atmel,at91sam9260-gpbr", "syscon";
+				reg = <0xfffffe60 0x10>;
+			};
+
+			rtc: rtc@fffffea8 {
+				compatible = "microchip,sam9x60-rtc", "atmel,at91sam9x5-rtc";
+				reg = <0xfffffea8 0x100>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&clk32k 1>;
+			};
+
+			watchdog: watchdog@ffffff80 {
+				compatible = "microchip,sam9x60-wdt";
+				reg = <0xffffff80 0x24>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&clk32k 0>;
+				status = "disabled";
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/microchip/sam9x7.dtsi b/arch/arm/boot/dts/microchip/sam9x7.dtsi
new file mode 100644
index 000000000000..46dacbbd201d
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/sam9x7.dtsi
@@ -0,0 +1,1316 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * sam9x7.dtsi - Device Tree Include file for Microchip SAM9X7 SoC family
+ *
+ * Copyright (C) 2023 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Varshini Rajendran <varshini.rajendran@microchip.com>
+ */
+
+#include <dt-bindings/clock/at91.h>
+#include <dt-bindings/dma/at91.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/mfd/at91-usart.h>
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/pinctrl/at91.h>
+
+/ {
+	model = "Microchip SAM9X7 SoC";
+	compatible = "microchip,sam9x7";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&aic>;
+
+	aliases {
+		serial0 = &dbgu;
+		gpio0 = &pioA;
+		gpio1 = &pioB;
+		gpio2 = &pioC;
+		gpio3 = &pioD;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "arm,arm926ej-s";
+			reg = <0>;
+			device_type = "cpu";
+		};
+	};
+
+	clocks {
+		slow_xtal: clock-slowxtal {
+			compatible = "fixed-clock";
+			clock-output-names = "slow_xtal";
+			#clock-cells = <0>;
+		};
+
+		main_xtal: clock-mainxtal {
+			compatible = "fixed-clock";
+			clock-output-names = "main_xtal";
+			#clock-cells = <0>;
+		};
+	};
+
+	sram: sram@300000 {
+		compatible = "mmio-sram";
+		reg = <0x300000 0x10000>;
+		ranges = <0 0x300000 0x10000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+
+	ahb {
+		compatible = "simple-bus";
+		ranges;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		sdmmc0: mmc@80000000 {
+			compatible = "microchip,sam9x7-sdhci", "microchip,sam9x60-sdhci";
+			reg = <0x80000000 0x300>;
+			interrupts = <12 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 12>, <&pmc PMC_TYPE_GCK 12>;
+			clock-names = "hclock", "multclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 12>;
+			assigned-clock-rates = <100000000>;
+			status = "disabled";
+		};
+
+		sdmmc1: mmc@90000000 {
+			compatible = "microchip,sam9x7-sdhci", "microchip,sam9x60-sdhci";
+			reg = <0x90000000 0x300>;
+			interrupts = <26 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 26>, <&pmc PMC_TYPE_GCK 26>;
+			clock-names = "hclock", "multclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 26>;
+			assigned-clock-rates = <100000000>;
+			status = "disabled";
+		};
+	};
+
+	apb {
+		compatible = "simple-bus";
+		ranges;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		flx4: flexcom@f0000000 {
+			compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xf0000000 0x200>;
+			ranges = <0x0 0xf0000000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+			status = "disabled";
+
+			uart4: serial@200 {
+				compatible = "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+				clock-names = "usart";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(8))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(9))>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			spi4: spi@400 {
+				compatible = "microchip,sam9x7-spi", "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+				clock-names = "spi_clk";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(8))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(9))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+
+			i2c4: i2c@600 {
+				compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(8))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(9))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		flx5: flexcom@f0004000 {
+			compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xf0004000 0x200>;
+			ranges = <0x0 0xf0004000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+			status = "disabled";
+
+			uart5: serial@200 {
+				compatible = "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+				clock-names = "usart";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(10))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(11))>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			spi5: spi@400 {
+				compatible = "microchip,sam9x7-spi", "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+				clock-names = "spi_clk";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(10))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(11))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+
+			i2c5: i2c@600 {
+				compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(10))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(11))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		dma0: dma-controller@f0008000 {
+			compatible = "microchip,sam9x7-dma", "atmel,sama5d4-dma";
+			reg = <0xf0008000 0x1000>;
+			interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
+			#dma-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 20>;
+			clock-names = "dma_clk";
+			status = "disabled";
+		};
+
+		ssc: ssc@f0010000 {
+			compatible = "microchip,sam9x7-ssc", "atmel,at91sam9g45-ssc";
+			reg = <0xf0010000 0x4000>;
+			interrupts = <28 IRQ_TYPE_LEVEL_HIGH 5>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 28>;
+			clock-names = "pclk";
+			dmas = <&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				 AT91_XDMAC_DT_PERID(38))>,
+			       <&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				 AT91_XDMAC_DT_PERID(39))>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		qspi: spi@f0014000 {
+			compatible = "microchip,sam9x7-ospi";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0xf0014000 0x100>, <0x60000000 0x20000000>;
+			reg-names = "qspi_base", "qspi_mmap";
+			interrupts = <35 IRQ_TYPE_LEVEL_HIGH 7>;
+			dmas = <&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				AT91_XDMAC_DT_PERID(26))>,
+				<&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				AT91_XDMAC_DT_PERID(27))>;
+			dma-names = "tx", "rx";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 35>, <&pmc PMC_TYPE_GCK 35>;
+			clock-names = "pclk", "gclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 35>;
+			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_PLLADIV2>;
+			status = "disabled";
+		};
+
+		i2s: i2s@f001c000 {
+			compatible = "microchip,sam9x7-i2smcc", "microchip,sam9x60-i2smcc";
+			reg = <0xf001c000 0x100>;
+			interrupts = <34 IRQ_TYPE_LEVEL_HIGH 7>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 34>, <&pmc PMC_TYPE_GCK 34>;
+			clock-names = "pclk", "gclk";
+			dmas = <&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				 AT91_XDMAC_DT_PERID(36))>,
+			       <&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				 AT91_XDMAC_DT_PERID(37))>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		flx11: flexcom@f0020000 {
+			compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xf0020000 0x200>;
+			ranges = <0x0 0xf0020000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
+			status = "disabled";
+
+			uart11: serial@200 {
+				compatible = "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
+				clock-names = "usart";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(22))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(23))>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			i2c11: i2c@600 {
+				compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(22))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(23))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		flx12: flexcom@f0024000 {
+			compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xf0024000 0x200>;
+			ranges = <0x0 0xf0024000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
+			status = "disabled";
+
+			uart12: serial@200 {
+				compatible = "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
+				clock-names = "usart";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(24))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(25))>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			i2c12: i2c@600 {
+				compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(24))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(25))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		pit64b0: timer@f0028000 {
+			compatible = "microchip,sam9x7-pit64b", "microchip,sam9x60-pit64b";
+			reg = <0xf0028000 0x100>;
+			interrupts = <37 IRQ_TYPE_LEVEL_HIGH 7>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 37>, <&pmc PMC_TYPE_GCK 37>;
+			clock-names = "pclk", "gclk";
+		};
+
+		sha: crypto@f002c000 {
+			compatible = "microchip,sam9x7-sha", "atmel,at91sam9g46-sha";
+			reg = <0xf002c000 0x100>;
+			interrupts = <41 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 41>;
+			clock-names = "sha_clk";
+			dmas = <&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				 AT91_XDMAC_DT_PERID(34))>;
+			dma-names = "tx";
+		};
+
+		trng: rng@f0030000 {
+			compatible = "microchip,sam9x7-trng", "microchip,sam9x60-trng";
+			reg = <0xf0030000 0x100>;
+			interrupts = <38 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 38>;
+			status = "disabled";
+		};
+
+		aes: crypto@f0034000 {
+			compatible = "microchip,sam9x7-aes", "atmel,at91sam9g46-aes";
+			reg = <0xf0034000 0x100>;
+			interrupts = <39 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 39>;
+			clock-names = "aes_clk";
+			dmas = <&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				 AT91_XDMAC_DT_PERID(32))>,
+			       <&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				 AT91_XDMAC_DT_PERID(33))>;
+			dma-names = "tx", "rx";
+		};
+
+		tdes: crypto@f0038000 {
+			compatible = "microchip,sam9x7-tdes", "atmel,at91sam9g46-tdes";
+			reg = <0xf0038000 0x100>;
+			interrupts = <40 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 40>;
+			clock-names = "tdes_clk";
+			dmas = <&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				 AT91_XDMAC_DT_PERID(31))>,
+			       <&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				 AT91_XDMAC_DT_PERID(30))>;
+			dma-names = "tx", "rx";
+		};
+
+		classd: sound@f003c000 {
+			compatible = "microchip,sam9x7-classd", "atmel,sama5d2-classd";
+			reg = <0xf003c000 0x100>;
+			interrupts = <42 IRQ_TYPE_LEVEL_HIGH 7>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 42>, <&pmc PMC_TYPE_GCK 42>;
+			clock-names = "pclk", "gclk";
+			dmas = <&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				 AT91_XDMAC_DT_PERID(35))>;
+			dma-names = "tx";
+			status = "disabled";
+		};
+
+		pit64b1: timer@f0040000 {
+			compatible = "microchip,sam9x7-pit64b", "microchip,sam9x60-pit64b";
+			reg = <0xf0040000 0x100>;
+			interrupts = <58 IRQ_TYPE_LEVEL_HIGH 7>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 58>, <&pmc PMC_TYPE_GCK 58>;
+			clock-names = "pclk", "gclk";
+		};
+
+		can0: can@f8000000 {
+			compatible = "bosch,m_can";
+			reg = <0xf8000000 0x100>, <0x300000 0x7800>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <29 IRQ_TYPE_LEVEL_HIGH 0>,
+				     <68 IRQ_TYPE_LEVEL_HIGH 0>;
+			interrupt-names = "int0", "int1";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 29>, <&pmc PMC_TYPE_GCK 29>;
+			clock-names = "hclk", "cclk";
+			assigned-clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_GCK 29>;
+			assigned-clock-rates = <480000000>, <40000000>;
+			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_CORE PMC_UTMI>;
+			bosch,mram-cfg = <0x3400 0 0 64 0 0 32 32>;
+			status = "disabled";
+		};
+
+		can1: can@f8004000 {
+			compatible = "bosch,m_can";
+			reg = <0xf8004000 0x100>, <0x300000 0xbc00>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <30 IRQ_TYPE_LEVEL_HIGH 0>,
+				     <69 IRQ_TYPE_LEVEL_HIGH 0>;
+			interrupt-names = "int0", "int1";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 30>, <&pmc PMC_TYPE_GCK 30>;
+			clock-names = "hclk", "cclk";
+			assigned-clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_GCK 30>;
+			assigned-clock-rates = <480000000>, <40000000>;
+			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_CORE PMC_UTMI>;
+			bosch,mram-cfg = <0x7800 0 0 64 0 0 32 32>;
+			status = "disabled";
+		};
+
+		tcb: timer@f8008000 {
+			compatible = "microchip,sam9x7-tcb","atmel,sama5d2-tcb", "simple-mfd", "syscon";
+			reg = <0xf8008000 0x100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 17>, <&pmc PMC_TYPE_GCK 17>, <&clk32k 0>;
+			clock-names = "t0_clk", "gclk", "slow_clk";
+		};
+
+		flx6: flexcom@f8010000 {
+			compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xf8010000 0x200>;
+			ranges = <0x0 0xf8010000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+			status = "disabled";
+
+			uart6: serial@200 {
+				compatible = "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+				clock-names = "usart";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(12))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(13))>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			i2c6: i2c@600 {
+				compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(12))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(13))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		flx7: flexcom@f8014000 {
+			compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xf8014000 0x200>;
+			ranges = <0x0 0xf8014000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+			status = "disabled";
+
+			uart7: serial@200 {
+				compatible = "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+				clock-names = "usart";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(14))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(15))>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			i2c7: i2c@600 {
+				compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(14))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(15))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		flx8: flexcom@f8018000 {
+			compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xf8018000 0x200>;
+			ranges = <0x0 0xf8018000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+			status = "disabled";
+
+			uart8: serial@200 {
+				compatible = "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+				clock-names = "usart";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(16))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(17))>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			i2c8: i2c@600 {
+				compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(16))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(17))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		flx0: flexcom@f801c000 {
+			compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xf801c000 0x200>;
+			ranges = <0x0 0xf801c000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+			status = "disabled";
+
+			uart0: serial@200 {
+				compatible = "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+				clock-names = "usart";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(0))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(1))>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			spi0: spi@400 {
+				compatible = "microchip,sam9x7-spi", "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+				clock-names = "spi_clk";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(0))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(1))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+
+			i2c0: i2c@600 {
+				compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(0))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(1))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		flx1: flexcom@f8020000 {
+			compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xf8020000 0x200>;
+			ranges = <0x0 0xf8020000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+			status = "disabled";
+
+			uart1: serial@200 {
+				compatible = "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+				clock-names = "usart";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(2))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(3))>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			spi1: spi@400 {
+				compatible = "microchip,sam9x7-spi", "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+				clock-names = "spi_clk";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(2))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(3))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@600 {
+				compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(2))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(3))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		flx2: flexcom@f8024000 {
+			compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xf8024000 0x200>;
+			ranges = <0x0 0xf8024000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+			status = "disabled";
+
+			uart2: serial@200 {
+				compatible = "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+				clock-names = "usart";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(4))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(5))>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			spi2: spi@400 {
+				compatible = "microchip,sam9x7-spi", "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+				clock-names = "spi_clk";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(4))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(5))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+
+			i2c2: i2c@600 {
+				compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(4))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(5))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		flx3: flexcom@f8028000 {
+			compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xf8028000 0x200>;
+			ranges = <0x0 0xf8028000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+			status = "disabled";
+
+			uart3: serial@200 {
+				compatible = "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+				clock-names = "usart";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(6))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(7))>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			spi3: spi@400 {
+				compatible = "microchip,sam9x7-spi", "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+				clock-names = "spi_clk";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(6))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(7))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+
+			i2c3: i2c@600 {
+				compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(6))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(7))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		gmac: ethernet@f802c000 {
+			compatible = "microchip,sam9x7-gem", "microchip,sama7g5-gem";
+			reg = <0xf802c000 0x1000>;
+			interrupts = <24 IRQ_TYPE_LEVEL_HIGH 3>,	/* Queue 0 */
+				     <60 IRQ_TYPE_LEVEL_HIGH 3>,	/* Queue 1 */
+				     <61 IRQ_TYPE_LEVEL_HIGH 3>,	/* Queue 2 */
+				     <62 IRQ_TYPE_LEVEL_HIGH 3>,	/* Queue 3 */
+				     <63 IRQ_TYPE_LEVEL_HIGH 3>,	/* Queue 4 */
+				     <64 IRQ_TYPE_LEVEL_HIGH 3>;	/* Queue 5 */
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 24>, <&pmc PMC_TYPE_PERIPHERAL 24>, <&pmc PMC_TYPE_GCK 24>, <&pmc PMC_TYPE_GCK 67>;
+			clock-names = "hclk", "pclk", "tx_clk", "tsu_clk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 67>;
+			assigned-clock-rates = <266666666>;
+			status = "disabled";
+		};
+
+		pwm0: pwm@f8034000 {
+			compatible = "microchip,sam9x7-pwm", "microchip,sam9x60-pwm";
+			reg = <0xf8034000 0x300>;
+			interrupts = <18 IRQ_TYPE_LEVEL_HIGH 4>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 18>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
+		hlcdc: hlcdc@f8038000 {
+			compatible = "microchip,sam9x75-xlcdc";
+			reg = <0xf8038000 0x4000>;
+			interrupts = <25 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 25>, <&pmc PMC_TYPE_GCK 25>, <&clk32k 1>;
+			clock-names = "periph_clk", "sys_clk", "slow_clk";
+			status = "disabled";
+
+			display-controller {
+				compatible = "atmel,hlcdc-display-controller";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+			};
+
+			pwm {
+				compatible = "atmel,hlcdc-pwm";
+				#pwm-cells = <3>;
+			};
+		};
+
+		flx9: flexcom@f8040000 {
+			compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xf8040000 0x200>;
+			ranges = <0x0 0xf8040000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
+			status = "disabled";
+
+			uart9: serial@200 {
+				compatible = "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
+				clock-names = "usart";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(18))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(19))>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			i2c9: i2c@600 {
+				compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(18))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(19))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		flx10: flexcom@f8044000 {
+			compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xf8044000 0x200>;
+			ranges = <0x0 0xf8044000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
+			status = "disabled";
+
+			uart10: serial@200 {
+				compatible = "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
+				clock-names = "usart";
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(20))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(21))>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			i2c10: i2c@600 {
+				compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(20))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) |
+					 AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(21))>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		lvds_controller: lvds-controller@f8060000 {
+			compatible = "microchip,sam9x75-lvds";
+			reg = <0xf8060000 0x100>;
+			interrupts = <56 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 56>;
+			clock-names = "pclk";
+			status = "disabled";
+		};
+
+		matrix: matrix@ffffde00 {
+			compatible = "microchip,sam9x7-matrix", "atmel,at91sam9x5-matrix", "syscon";
+			reg = <0xffffde00 0x200>;
+		};
+
+		pmecc: ecc-engine@ffffe000 {
+			compatible = "microchip,sam9x7-pmecc", "atmel,at91sam9g45-pmecc";
+			reg = <0xffffe000 0x300>, <0xffffe600 0x100>;
+		};
+
+		mpddrc: mpddrc@ffffe800 {
+			compatible = "microchip,sam9x7-ddramc", "atmel,sama5d3-ddramc";
+			reg = <0xffffe800 0x200>;
+			clocks = <&pmc PMC_TYPE_SYSTEM 2>, <&pmc PMC_TYPE_CORE PMC_MCK>;
+			clock-names = "ddrck", "mpddr";
+		};
+
+		smc: smc@ffffea00 {
+			compatible = "microchip,sam9x7-smc", "atmel,at91sam9260-smc", "syscon";
+			reg = <0xffffea00 0x100>;
+		};
+
+		aic: interrupt-controller@fffff100 {
+			compatible = "microchip,sam9x7-aic";
+			reg = <0xfffff100 0x100>;
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			atmel,external-irqs = <31>;
+		};
+
+		dbgu: serial@fffff200 {
+			compatible = "microchip,sam9x7-dbgu", "atmel,at91sam9260-dbgu", "microchip,sam9x7-usart", "atmel,at91sam9260-usart";
+			reg = <0xfffff200 0x200>;
+			interrupts = <47 IRQ_TYPE_LEVEL_HIGH 7>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 47>;
+			clock-names = "usart";
+			dmas = <&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				 AT91_XDMAC_DT_PERID(28))>,
+			       <&dma0
+				(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+				 AT91_XDMAC_DT_PERID(29))>;
+			dma-names = "tx", "rx";
+			atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+			status = "disabled";
+		};
+
+		pinctrl: pinctrl@fffff400 {
+			compatible = "microchip,sam9x7-pinctrl", "microchip,sam9x60-pinctrl", "simple-mfd";
+			ranges = <0xfffff400 0xfffff400 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			/* mux-mask corresponding to sam9x7 SoC in TFBGA228L package */
+			atmel,mux-mask = <
+					 /*  A		B	   C	      D	  */
+					 0xffffffff 0xffffefc0 0xc0ffd000 0x00000000	/* pioA */
+					 0x07ffffff 0x0805fe7f 0x01ff9f81 0x06078000	/* pioB */
+					 0xffffffff 0x07dfffff 0xfa3fffff 0x00000000	/* pioC */
+					 0x00003fff 0x00003fe0 0x0000003f 0x00000000	/* pioD */
+					 >;
+
+			pioA: gpio@fffff400 {
+				compatible = "microchip,sam9x7-gpio", "microchip,sam9x60-gpio", "atmel,at91rm9200-gpio";
+				reg = <0xfffff400 0x200>;
+				interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
+				#interrupt-cells = <2>;
+				interrupt-controller;
+				#gpio-cells = <2>;
+				gpio-controller;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 2>;
+			};
+
+			pioB: gpio@fffff600 {
+				compatible = "microchip,sam9x7-gpio", "microchip,sam9x60-gpio", "atmel,at91rm9200-gpio";
+				reg = <0xfffff600 0x200>;
+				interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
+				#interrupt-cells = <2>;
+				interrupt-controller;
+				#gpio-cells = <2>;
+				gpio-controller;
+				#gpio-lines = <26>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 3>;
+			};
+
+			pioC: gpio@fffff800 {
+				compatible = "microchip,sam9x7-gpio", "microchip,sam9x60-gpio", "atmel,at91rm9200-gpio";
+				reg = <0xfffff800 0x200>;
+				interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>;
+				#interrupt-cells = <2>;
+				interrupt-controller;
+				#gpio-cells = <2>;
+				gpio-controller;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 4>;
+			};
+
+			pioD: gpio@fffffa00 {
+				compatible = "microchip,sam9x7-gpio", "microchip,sam9x60-gpio", "atmel,at91rm9200-gpio";
+				reg = <0xfffffa00 0x200>;
+				interrupts = <44 IRQ_TYPE_LEVEL_HIGH 1>;
+				#interrupt-cells = <2>;
+				interrupt-controller;
+				#gpio-cells = <2>;
+				gpio-controller;
+				#gpio-lines = <22>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 44>;
+			};
+		};
+
+		pmc: clock-controller@fffffc00 {
+			compatible = "microchip,sam9x7-pmc", "syscon";
+			reg = <0xfffffc00 0x200>;
+			interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+			#clock-cells = <2>;
+			clocks = <&clk32k 1>, <&clk32k 0>, <&main_xtal>;
+			clock-names = "td_slck", "md_slck", "main_xtal";
+		};
+
+		reset_controller: reset-controller@fffffe00 {
+			compatible = "microchip,sam9x7-rstc", "microchip,sam9x60-rstc";
+			reg = <0xfffffe00 0x10>;
+			clocks = <&clk32k 0>;
+		};
+
+		poweroff: poweroff@fffffe10 {
+			compatible = "microchip,sam9x7-shdwc", "microchip,sam9x60-shdwc";
+			reg = <0xfffffe10 0x10>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&clk32k 0>;
+			atmel,wakeup-rtc-timer;
+			atmel,wakeup-rtt-timer;
+			status = "disabled";
+		};
+
+		rtt: rtc@fffffe20 {
+			compatible = "microchip,sam9x7-rtt", "atmel,at91sam9260-rtt";
+			reg = <0xfffffe20 0x20>;
+			interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+			clocks = <&clk32k 0>;
+		};
+
+		clk32k: clock-controller@fffffe50 {
+			compatible = "microchip,sam9x7-sckc", "microchip,sam9x60-sckc";
+			reg = <0xfffffe50 0x4>;
+			clocks = <&slow_xtal>;
+			#clock-cells = <1>;
+		};
+
+		gpbr: syscon@fffffe60 {
+			compatible = "microchip,sam9x7-gpbr", "atmel,at91sam9260-gpbr", "syscon";
+			reg = <0xfffffe60 0x10>;
+		};
+
+		rtc: rtc@fffffea8 {
+			compatible = "microchip,sam9x7-rtc", "microchip,sam9x60-rtc";
+			reg = <0xfffffea8 0x100>;
+			interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+			clocks = <&clk32k 0>;
+		};
+
+		watchdog: watchdog@ffffff80 {
+			compatible = "microchip,sam9x7-wdt", "microchip,sam9x60-wdt";
+			reg = <0xffffff80 0x24>;
+			interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/sama5d2-pinfunc.h b/arch/arm/boot/dts/microchip/sama5d2-pinfunc.h
index 28a2e45752fe..28a2e45752fe 100644
--- a/arch/arm/boot/dts/sama5d2-pinfunc.h
+++ b/arch/arm/boot/dts/microchip/sama5d2-pinfunc.h
diff --git a/arch/arm/boot/dts/sama5d2.dtsi b/arch/arm/boot/dts/microchip/sama5d2.dtsi
index 89c71d419f82..17430d7f2055 100644
--- a/arch/arm/boot/dts/sama5d2.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d2.dtsi
@@ -9,6 +9,7 @@
 #include <dt-bindings/dma/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 #include <dt-bindings/iio/adc/at91-sama5d2_adc.h>
 
 / {
@@ -31,6 +32,8 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a5";
 			reg = <0>;
+			d-cache-size = <0x8000>;	// L1, 32 KB
+			i-cache-size = <0x8000>;	// L1, 32 KB
 			next-level-cache = <&L2>;
 		};
 	};
@@ -99,6 +102,16 @@
 		ranges = <0 0x00200000 0x20000>;
 	};
 
+	resistive_touch: resistive-touch {
+		compatible = "resistive-adc-touch";
+		io-channels = <&adc AT91_SAMA5D2_ADC_X_CHANNEL>,
+			      <&adc AT91_SAMA5D2_ADC_Y_CHANNEL>,
+			      <&adc AT91_SAMA5D2_ADC_P_CHANNEL>;
+		io-channel-names = "x", "y", "pressure";
+		touchscreen-min-pressure = <50000>;
+		status = "disabled";
+	};
+
 	ahb {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -125,7 +138,7 @@
 			status = "disabled";
 		};
 
-		usb1: ohci@400000 {
+		usb1: usb@400000 {
 			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
 			reg = <0x00400000 0x100000>;
 			interrupts = <41 IRQ_TYPE_LEVEL_HIGH 2>;
@@ -134,7 +147,7 @@
 			status = "disabled";
 		};
 
-		usb2: ehci@500000 {
+		usb2: usb@500000 {
 			compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
 			reg = <0x00500000 0x100000>;
 			interrupts = <41 IRQ_TYPE_LEVEL_HIGH 2>;
@@ -149,6 +162,7 @@
 			interrupts = <63 IRQ_TYPE_LEVEL_HIGH 4>;
 			cache-unified;
 			cache-level = <2>;
+			cache-size = <0x20000>;		// L2, 128 KB
 		};
 
 		ebi: ebi@10000000 {
@@ -273,7 +287,7 @@
 				clock-names = "dma_clk";
 			};
 
-			pmc: pmc@f0014000 {
+			pmc: clock-controller@f0014000 {
 				compatible = "atmel,sama5d2-pmc", "syscon";
 				reg = <0xf0014000 0x160>;
 				interrupts = <74 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -371,11 +385,9 @@
 			macb0: ethernet@f8008000 {
 				compatible = "atmel,sama5d2-gem";
 				reg = <0xf8008000 0x1000>;
-				interrupts = <5  IRQ_TYPE_LEVEL_HIGH 3		/* Queue 0 */
-					      66 IRQ_TYPE_LEVEL_HIGH 3          /* Queue 1 */
-					      67 IRQ_TYPE_LEVEL_HIGH 3>;        /* Queue 2 */
-				#address-cells = <1>;
-				#size-cells = <0>;
+				interrupts = <5  IRQ_TYPE_LEVEL_HIGH 3>,	/* Queue 0 */
+					     <66 IRQ_TYPE_LEVEL_HIGH 3>,	/* Queue 1 */
+					     <67 IRQ_TYPE_LEVEL_HIGH 3>;        /* Queue 2 */
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 5>, <&pmc PMC_TYPE_PERIPHERAL 5>;
 				clock-names = "hclk", "pclk";
 				status = "disabled";
@@ -433,6 +445,7 @@
 			uart0: serial@f801c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf801c000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <24 IRQ_TYPE_LEVEL_HIGH 7>;
 				dmas = <&dma0
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
@@ -449,6 +462,7 @@
 			uart1: serial@f8020000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8020000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <25 IRQ_TYPE_LEVEL_HIGH 7>;
 				dmas = <&dma0
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
@@ -465,6 +479,7 @@
 			uart2: serial@f8024000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8024000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <26 IRQ_TYPE_LEVEL_HIGH 7>;
 				dmas = <&dma0
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
@@ -522,6 +537,7 @@
 				uart5: serial@200 {
 					compatible = "atmel,at91sam9260-usart";
 					reg = <0x200 0x200>;
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 					interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
 					clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
 					clock-names = "usart";
@@ -592,6 +608,7 @@
 				uart6: serial@200 {
 					compatible = "atmel,at91sam9260-usart";
 					reg = <0x200 0x200>;
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 					interrupts = <20 IRQ_TYPE_LEVEL_HIGH 7>;
 					clocks = <&pmc PMC_TYPE_PERIPHERAL 20>;
 					clock-names = "usart";
@@ -660,13 +677,13 @@
 				ranges = <0 0xf8044000 0x1420>;
 			};
 
-			reset_controller: rstc@f8048000 {
+			reset_controller: reset-controller@f8048000 {
 				compatible = "atmel,sama5d3-rstc";
 				reg = <0xf8048000 0x10>;
 				clocks = <&clk32k>;
 			};
 
-			shutdown_controller: shdwc@f8048010 {
+			shutdown_controller: poweroff@f8048010 {
 				compatible = "atmel,sama5d2-shdwc";
 				reg = <0xf8048010 0x10>;
 				clocks = <&clk32k>;
@@ -690,10 +707,9 @@
 				status = "disabled";
 			};
 
-			clk32k: sckc@f8048050 {
+			clk32k: clock-controller@f8048050 {
 				compatible = "atmel,sama5d4-sckc";
 				reg = <0xf8048050 0x4>;
-
 				clocks = <&slow_xtal>;
 				#clock-cells = <0>;
 			};
@@ -761,6 +777,7 @@
 			uart3: serial@fc008000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfc008000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <27 IRQ_TYPE_LEVEL_HIGH 7>;
 				dmas = <&dma1
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
@@ -777,6 +794,7 @@
 			uart4: serial@fc00c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfc00c000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				dmas = <&dma0
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
 					 AT91_XDMAC_DT_PERID(43))>,
@@ -802,6 +820,7 @@
 				uart7: serial@200 {
 					compatible = "atmel,at91sam9260-usart";
 					reg = <0x200 0x200>;
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 					interrupts = <21 IRQ_TYPE_LEVEL_HIGH 7>;
 					clocks = <&pmc PMC_TYPE_PERIPHERAL 21>;
 					clock-names = "usart";
@@ -872,6 +891,7 @@
 				uart8: serial@200 {
 					compatible = "atmel,at91sam9260-usart";
 					reg = <0x200 0x200>;
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 					interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
 					clocks = <&pmc PMC_TYPE_PERIPHERAL 22>;
 					clock-names = "usart";
@@ -943,6 +963,7 @@
 				uart9: serial@200 {
 					compatible = "atmel,at91sam9260-usart";
 					reg = <0x200 0x200>;
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 					interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
 					clocks = <&pmc PMC_TYPE_PERIPHERAL 23>;
 					clock-names = "usart";
@@ -1001,7 +1022,7 @@
 				};
 			};
 
-			trng@fc01c000 {
+			trng: rng@fc01c000 {
 				compatible = "atmel,at91sam9g45-trng";
 				reg = <0xfc01c000 0x100>;
 				interrupts = <47 IRQ_TYPE_LEVEL_HIGH 0>;
@@ -1050,16 +1071,6 @@
 				status = "disabled";
 			};
 
-			resistive_touch: resistive-touch {
-				compatible = "resistive-adc-touch";
-				io-channels = <&adc AT91_SAMA5D2_ADC_X_CHANNEL>,
-					      <&adc AT91_SAMA5D2_ADC_Y_CHANNEL>,
-					      <&adc AT91_SAMA5D2_ADC_P_CHANNEL>;
-				io-channel-names = "x", "y", "pressure";
-				touchscreen-min-pressure = <50000>;
-				status = "disabled";
-			};
-
 			pioA: pinctrl@fc038000 {
 				compatible = "atmel,sama5d2-pinctrl";
 				reg = <0xfc038000 0x600>;
@@ -1124,7 +1135,7 @@
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 55>, <&pmc PMC_TYPE_GCK 55>;
 				clock-names = "pclk", "gclk";
 				assigned-clocks = <&pmc PMC_TYPE_CORE PMC_I2S1_MUX>;
-				assigned-parrents = <&pmc PMC_TYPE_GCK 55>;
+				assigned-clock-parents = <&pmc PMC_TYPE_GCK 55>;
 				status = "disabled";
 			};
 
diff --git a/arch/arm/boot/dts/sama5d29.dtsi b/arch/arm/boot/dts/microchip/sama5d29.dtsi
index 17991c28a256..17991c28a256 100644
--- a/arch/arm/boot/dts/sama5d29.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d29.dtsi
diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/microchip/sama5d3.dtsi
index 8fa423c52592..00ba59ac1968 100644
--- a/arch/arm/boot/dts/sama5d3.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3.dtsi
@@ -12,6 +12,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	#address-cells = <1>;
@@ -47,6 +48,8 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a5";
 			reg = <0x0>;
+			d-cache-size = <0x8000>;	// L1, 32 KB
+			i-cache-size = <0x8000>;	// L1, 32 KB
 		};
 	};
 
@@ -73,7 +76,7 @@
 			clock-frequency = <0>;
 		};
 
-		adc_op_clk: adc_op_clk{
+		adc_op_clk: adc_op_clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <1000000>;
@@ -194,6 +197,7 @@
 			usart0: serial@f001c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf001c000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <12 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(3)>,
 				       <&dma0 2 (AT91_DMA_CFG_PER_ID(4) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
@@ -208,6 +212,7 @@
 			usart1: serial@f0020000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf0020000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <13 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(5)>,
 				       <&dma0 2 (AT91_DMA_CFG_PER_ID(6) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
@@ -222,6 +227,7 @@
 			uart0: serial@f0024000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf0024000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <16 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_uart0>;
@@ -356,6 +362,7 @@
 			usart2: serial@f8020000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8020000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <14 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(7)>,
 				       <&dma1 2 (AT91_DMA_CFG_PER_ID(8) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
@@ -370,6 +377,7 @@
 			usart3: serial@f8024000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8024000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(9)>,
 				       <&dma1 2 (AT91_DMA_CFG_PER_ID(10) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
@@ -413,7 +421,7 @@
 				clock-names = "tdes_clk";
 			};
 
-			trng@f8040000 {
+			trng: rng@f8040000 {
 				compatible = "atmel,at91sam9g45-trng";
 				reg = <0xf8040000 0x100>;
 				interrupts = <45 IRQ_TYPE_LEVEL_HIGH 0>;
@@ -464,6 +472,7 @@
 			dbgu: serial@ffffee00 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xffffee00 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <2 IRQ_TYPE_LEVEL_HIGH 7>;
 				dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(13)>,
 				       <&dma1 2 (AT91_DMA_CFG_PER_ID(14) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
@@ -486,7 +495,7 @@
 			pinctrl: pinctrl@fffff200 {
 				#address-cells = <1>;
 				#size-cells = <1>;
-				compatible = "atmel,sama5d3-pinctrl", "atmel,at91sam9x5-pinctrl", "simple-bus";
+				compatible = "atmel,sama5d3-pinctrl", "simple-mfd";
 				ranges = <0xfffff200 0xfffff200 0xa00>;
 				atmel,mux-mask = <
 					/*   A          B          C  */
@@ -994,7 +1003,7 @@
 				};
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 				compatible = "atmel,sama5d3-pmc", "syscon";
 				reg = <0xfffffc00 0x120>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -1003,13 +1012,13 @@
 				clock-names = "slow_clk", "main_xtal";
 			};
 
-			reset_controller: rstc@fffffe00 {
+			reset_controller: reset-controller@fffffe00 {
 				compatible = "atmel,sama5d3-rstc", "atmel,at91sam9g45-rstc";
 				reg = <0xfffffe00 0x10>;
 				clocks = <&clk32k>;
 			};
 
-			shutdown_controller: shutdown-controller@fffffe10 {
+			shutdown_controller: poweroff@fffffe10 {
 				compatible = "atmel,at91sam9x5-shdwc";
 				reg = <0xfffffe10 0x10>;
 				clocks = <&clk32k>;
@@ -1033,7 +1042,7 @@
 				status = "disabled";
 			};
 
-			clk32k: sckc@fffffe50 {
+			clk32k: clock-controller@fffffe50 {
 				compatible = "atmel,sama5d3-sckc";
 				reg = <0xfffffe50 0x4>;
 				clocks = <&slow_xtal>;
@@ -1067,7 +1076,7 @@
 			status = "disabled";
 		};
 
-		usb1: ohci@600000 {
+		usb1: usb@600000 {
 			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
 			reg = <0x00600000 0x100000>;
 			interrupts = <32 IRQ_TYPE_LEVEL_HIGH 2>;
@@ -1076,7 +1085,7 @@
 			status = "disabled";
 		};
 
-		usb2: ehci@700000 {
+		usb2: usb@700000 {
 			compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
 			reg = <0x00700000 0x100000>;
 			interrupts = <32 IRQ_TYPE_LEVEL_HIGH 2>;
diff --git a/arch/arm/boot/dts/sama5d31.dtsi b/arch/arm/boot/dts/microchip/sama5d31.dtsi
index cbe8f275ecc4..cbe8f275ecc4 100644
--- a/arch/arm/boot/dts/sama5d31.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d31.dtsi
diff --git a/arch/arm/boot/dts/sama5d31ek.dts b/arch/arm/boot/dts/microchip/sama5d31ek.dts
index 10fc80d6d30d..1f2dfb3127ab 100644
--- a/arch/arm/boot/dts/sama5d31ek.dts
+++ b/arch/arm/boot/dts/microchip/sama5d31ek.dts
@@ -40,7 +40,7 @@
 	};
 
 	leds {
-		d3 {
+		led-d3 {
 			label = "d3";
 			gpios = <&pioE 24 GPIO_ACTIVE_HIGH>;
 		};
diff --git a/arch/arm/boot/dts/sama5d33.dtsi b/arch/arm/boot/dts/microchip/sama5d33.dtsi
index 146fd59acea5..146fd59acea5 100644
--- a/arch/arm/boot/dts/sama5d33.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d33.dtsi
diff --git a/arch/arm/boot/dts/sama5d33ek.dts b/arch/arm/boot/dts/microchip/sama5d33ek.dts
index 7d4ae1682933..7d4ae1682933 100644
--- a/arch/arm/boot/dts/sama5d33ek.dts
+++ b/arch/arm/boot/dts/microchip/sama5d33ek.dts
diff --git a/arch/arm/boot/dts/sama5d34.dtsi b/arch/arm/boot/dts/microchip/sama5d34.dtsi
index 132918c889a0..132918c889a0 100644
--- a/arch/arm/boot/dts/sama5d34.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d34.dtsi
diff --git a/arch/arm/boot/dts/sama5d34ek.dts b/arch/arm/boot/dts/microchip/sama5d34ek.dts
index 2335bf906f69..18943b873fff 100644
--- a/arch/arm/boot/dts/sama5d34ek.dts
+++ b/arch/arm/boot/dts/microchip/sama5d34ek.dts
@@ -36,7 +36,7 @@
 			i2c1: i2c@f0018000 {
 				status = "okay";
 
-				24c256@50 {
+				eeprom@50 {
 					compatible = "atmel,24c256";
 					reg = <0x50>;
 					pagesize = <64>;
@@ -50,7 +50,7 @@
 	};
 
 	leds {
-		d3 {
+		led-d3 {
 			label = "d3";
 			gpios = <&pioE 24 GPIO_ACTIVE_HIGH>;
 		};
diff --git a/arch/arm/boot/dts/sama5d35.dtsi b/arch/arm/boot/dts/microchip/sama5d35.dtsi
index b2ccfa77c4be..b2ccfa77c4be 100644
--- a/arch/arm/boot/dts/sama5d35.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d35.dtsi
diff --git a/arch/arm/boot/dts/sama5d35ek.dts b/arch/arm/boot/dts/microchip/sama5d35ek.dts
index 8edfcebb1df0..8edfcebb1df0 100644
--- a/arch/arm/boot/dts/sama5d35ek.dts
+++ b/arch/arm/boot/dts/microchip/sama5d35ek.dts
diff --git a/arch/arm/boot/dts/sama5d36.dtsi b/arch/arm/boot/dts/microchip/sama5d36.dtsi
index 5d88f9967138..5d88f9967138 100644
--- a/arch/arm/boot/dts/sama5d36.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d36.dtsi
diff --git a/arch/arm/boot/dts/sama5d36ek.dts b/arch/arm/boot/dts/microchip/sama5d36ek.dts
index 26950f9284c2..26950f9284c2 100644
--- a/arch/arm/boot/dts/sama5d36ek.dts
+++ b/arch/arm/boot/dts/microchip/sama5d36ek.dts
diff --git a/arch/arm/boot/dts/sama5d36ek_cmp.dts b/arch/arm/boot/dts/microchip/sama5d36ek_cmp.dts
index 66695b9a3e77..66695b9a3e77 100644
--- a/arch/arm/boot/dts/sama5d36ek_cmp.dts
+++ b/arch/arm/boot/dts/microchip/sama5d36ek_cmp.dts
diff --git a/arch/arm/boot/dts/sama5d3_can.dtsi b/arch/arm/boot/dts/microchip/sama5d3_can.dtsi
index 9ac29bf3f933..9ac29bf3f933 100644
--- a/arch/arm/boot/dts/sama5d3_can.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3_can.dtsi
diff --git a/arch/arm/boot/dts/sama5d3_emac.dtsi b/arch/arm/boot/dts/microchip/sama5d3_emac.dtsi
index 45226108850d..5d7ce13de8cc 100644
--- a/arch/arm/boot/dts/sama5d3_emac.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3_emac.dtsi
@@ -30,7 +30,7 @@
 				};
 			};
 
-			pmc: pmc@fffffc00 {
+			pmc: clock-controller@fffffc00 {
 			};
 
 			macb1: ethernet@f802c000 {
diff --git a/arch/arm/boot/dts/sama5d3_gmac.dtsi b/arch/arm/boot/dts/microchip/sama5d3_gmac.dtsi
index 884df7a54dbb..884df7a54dbb 100644
--- a/arch/arm/boot/dts/sama5d3_gmac.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3_gmac.dtsi
diff --git a/arch/arm/boot/dts/sama5d3_lcd.dtsi b/arch/arm/boot/dts/microchip/sama5d3_lcd.dtsi
index 308d2fc276d6..308d2fc276d6 100644
--- a/arch/arm/boot/dts/sama5d3_lcd.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3_lcd.dtsi
diff --git a/arch/arm/boot/dts/sama5d3_mci2.dtsi b/arch/arm/boot/dts/microchip/sama5d3_mci2.dtsi
index 7141ee97ec3e..7141ee97ec3e 100644
--- a/arch/arm/boot/dts/sama5d3_mci2.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3_mci2.dtsi
diff --git a/arch/arm/boot/dts/sama5d3_tcb1.dtsi b/arch/arm/boot/dts/microchip/sama5d3_tcb1.dtsi
index 2b18c5c2cc03..2b18c5c2cc03 100644
--- a/arch/arm/boot/dts/sama5d3_tcb1.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3_tcb1.dtsi
diff --git a/arch/arm/boot/dts/sama5d3_uart.dtsi b/arch/arm/boot/dts/microchip/sama5d3_uart.dtsi
index a3eaba995cf4..44d1173f2ffb 100644
--- a/arch/arm/boot/dts/sama5d3_uart.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3_uart.dtsi
@@ -9,6 +9,7 @@
 #include <dt-bindings/pinctrl/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	aliases {
@@ -39,6 +40,7 @@
 			uart0: serial@f0024000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf0024000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <16 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_uart0>;
@@ -50,6 +52,7 @@
 			uart1: serial@f8028000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8028000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <17 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_uart1>;
diff --git a/arch/arm/boot/dts/sama5d3xcm.dtsi b/arch/arm/boot/dts/microchip/sama5d3xcm.dtsi
index 384335635792..7d1d7859edb4 100644
--- a/arch/arm/boot/dts/sama5d3xcm.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3xcm.dtsi
@@ -130,7 +130,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		d2 {
+		led-d2 {
 			label = "d2";
 			gpios = <&pioE 25 GPIO_ACTIVE_LOW>;	/* PE25, conflicts with A25, RXD2 */
 			linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi b/arch/arm/boot/dts/microchip/sama5d3xcm_cmp.dtsi
index 5579c955f141..362806afef44 100644
--- a/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3xcm_cmp.dtsi
@@ -79,7 +79,7 @@
 			};
 
 			i2c1: i2c@f0018000 {
-				pmic: act8865@5b {
+				act8865: pmic@5b {
 					compatible = "active-semi,act8865";
 					reg = <0x5b>;
 					status = "disabled";
@@ -184,7 +184,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		d2 {
+		led-d2 {
 			label = "d2";
 			gpios = <&pioE 25 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/sama5d3xdm.dtsi b/arch/arm/boot/dts/microchip/sama5d3xdm.dtsi
index 3c1c4d62fbf9..3c1c4d62fbf9 100644
--- a/arch/arm/boot/dts/sama5d3xdm.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3xdm.dtsi
diff --git a/arch/arm/boot/dts/sama5d3xmb.dtsi b/arch/arm/boot/dts/microchip/sama5d3xmb.dtsi
index a499de8a7a64..90da04b84b39 100644
--- a/arch/arm/boot/dts/sama5d3xmb.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3xmb.dtsi
@@ -26,7 +26,7 @@
 			spi0: spi@f0004000 {
 				dmas = <0>, <0>;	/*  Do not use DMA for spi0 */
 
-				m25p80@0 {
+				flash@0 {
 					compatible = "atmel,at25df321a";
 					spi-max-frequency = <50000000>;
 					reg = <0>;
@@ -172,7 +172,7 @@
 			status = "okay";
 		};
 
-		usb1: ohci@600000 {
+		usb1: usb@600000 {
 			num-ports = <3>;
 			atmel,vbus-gpio = <&pioD 25 GPIO_ACTIVE_HIGH
 					   &pioD 26 GPIO_ACTIVE_LOW
@@ -181,7 +181,7 @@
 			status = "okay";
 		};
 
-		usb2: ehci@700000 {
+		usb2: usb@700000 {
 			status = "okay";
 		};
 	};
diff --git a/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi b/arch/arm/boot/dts/microchip/sama5d3xmb_cmp.dtsi
index fa9e5e2a745d..5d9e97fecf83 100644
--- a/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3xmb_cmp.dtsi
@@ -25,7 +25,7 @@
 			spi0: spi@f0004000 {
 				dmas = <0>, <0>;	/*  Do not use DMA for spi0 */
 
-				m25p80@0 {
+				flash@0 {
 					compatible = "atmel,at25df321a";
 					spi-max-frequency = <50000000>;
 					reg = <0>;
diff --git a/arch/arm/boot/dts/sama5d3xmb_emac.dtsi b/arch/arm/boot/dts/microchip/sama5d3xmb_emac.dtsi
index a5dd41cd9522..a5dd41cd9522 100644
--- a/arch/arm/boot/dts/sama5d3xmb_emac.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3xmb_emac.dtsi
diff --git a/arch/arm/boot/dts/sama5d3xmb_gmac.dtsi b/arch/arm/boot/dts/microchip/sama5d3xmb_gmac.dtsi
index d750da38ff3c..d750da38ff3c 100644
--- a/arch/arm/boot/dts/sama5d3xmb_gmac.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d3xmb_gmac.dtsi
diff --git a/arch/arm/boot/dts/sama5d4.dtsi b/arch/arm/boot/dts/microchip/sama5d4.dtsi
index 7b9242664875..ec1d68c640de 100644
--- a/arch/arm/boot/dts/sama5d4.dtsi
+++ b/arch/arm/boot/dts/microchip/sama5d4.dtsi
@@ -8,6 +8,7 @@
 
 #include <dt-bindings/clock/at91.h>
 #include <dt-bindings/dma/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 #include <dt-bindings/pinctrl/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
@@ -49,6 +50,8 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a5";
 			reg = <0>;
+			d-cache-size = <0x8000>;	// L1, 32 KB
+			i-cache-size = <0x8000>;	// L1, 32 KB
 			next-level-cache = <&L2>;
 		};
 	};
@@ -71,7 +74,7 @@
 			clock-frequency = <0>;
 		};
 
-		adc_op_clk: adc_op_clk{
+		adc_op_clk: adc_op_clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <1000000>;
@@ -118,7 +121,7 @@
 			status = "disabled";
 		};
 
-		usb1: ohci@500000 {
+		usb1: usb@500000 {
 			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
 			reg = <0x00500000 0x100000>;
 			interrupts = <46 IRQ_TYPE_LEVEL_HIGH 2>;
@@ -127,7 +130,7 @@
 			status = "disabled";
 		};
 
-		usb2: ehci@600000 {
+		usb2: usb@600000 {
 			compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
 			reg = <0x00600000 0x100000>;
 			interrupts = <46 IRQ_TYPE_LEVEL_HIGH 2>;
@@ -142,6 +145,7 @@
 			interrupts = <67 IRQ_TYPE_LEVEL_HIGH 4>;
 			cache-unified;
 			cache-level = <2>;
+			cache-size = <0x20000>;		// L2, 128 KB
 		};
 
 		ebi: ebi@10000000 {
@@ -249,7 +253,7 @@
 				clock-names = "dma_clk";
 			};
 
-			pmc: pmc@f0018000 {
+			pmc: clock-controller@f0018000 {
 				compatible = "atmel,sama5d4-pmc", "syscon";
 				reg = <0xf0018000 0x120>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
@@ -278,6 +282,7 @@
 			uart0: serial@f8004000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8004000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <27 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma0
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -437,6 +442,7 @@
 			usart0: serial@f802c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf802c000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma0
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -455,6 +461,7 @@
 			usart1: serial@f8030000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8030000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma0
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -490,6 +497,7 @@
 			uart1: serial@fc004000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfc004000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <28 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma0
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -508,6 +516,7 @@
 			usart2: serial@fc008000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfc008000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <29 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma1
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -526,6 +535,7 @@
 			usart3: serial@fc00c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfc00c000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <30 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma1
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -544,6 +554,7 @@
 			usart4: serial@fc010000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfc010000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <31 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma1
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -650,7 +661,7 @@
 				status = "disabled";
 			};
 
-			trng@fc030000 {
+			trng: rng@fc030000 {
 				compatible = "atmel,at91sam9g45-trng";
 				reg = <0xfc030000 0x100>;
 				interrupts = <53 IRQ_TYPE_LEVEL_HIGH 0>;
@@ -686,7 +697,7 @@
 				clock-names = "aes_clk";
 			};
 
-			tdes: crpyto@fc04c000 {
+			tdes: crypto@fc04c000 {
 				compatible = "atmel,at91sam9g46-tdes";
 				reg = <0xfc04c000 0x100>;
 				interrupts = <14 IRQ_TYPE_LEVEL_HIGH 0>;
@@ -726,13 +737,13 @@
 				};
 			};
 
-			reset_controller: rstc@fc068600 {
+			reset_controller: reset-controller@fc068600 {
 				compatible = "atmel,sama5d3-rstc", "atmel,at91sam9g45-rstc";
 				reg = <0xfc068600 0x10>;
 				clocks = <&clk32k>;
 			};
 
-			shutdown_controller: shdwc@fc068610 {
+			shutdown_controller: poweroff@fc068610 {
 				compatible = "atmel,at91sam9x5-shdwc";
 				reg = <0xfc068610 0x10>;
 				clocks = <&clk32k>;
@@ -753,7 +764,7 @@
 				status = "disabled";
 			};
 
-			clk32k: sckc@fc068650 {
+			clk32k: clock-controller@fc068650 {
 				compatible = "atmel,sama5d4-sckc";
 				reg = <0xfc068650 0x4>;
 				#clock-cells = <0>;
@@ -770,6 +781,7 @@
 			dbgu: serial@fc069000 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xfc069000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <45 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
@@ -782,7 +794,7 @@
 			pinctrl: pinctrl@fc06a000 {
 				#address-cells = <1>;
 				#size-cells = <1>;
-				compatible = "atmel,sama5d3-pinctrl", "atmel,at91sam9x5-pinctrl", "simple-bus";
+				compatible = "atmel,sama5d3-pinctrl", "simple-mfd";
 				ranges = <0xfc068000 0xfc068000 0x100
 					  0xfc06a000 0xfc06a000 0x4000>;
 				/* WARNING: revisit as pin spec has changed */
diff --git a/arch/arm/boot/dts/microchip/sama7d65-pinfunc.h b/arch/arm/boot/dts/microchip/sama7d65-pinfunc.h
new file mode 100644
index 000000000000..c591f333cacb
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/sama7d65-pinfunc.h
@@ -0,0 +1,947 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
+#define PINMUX_PIN(no, func, ioset) \
+(((no) & 0xffff) | (((func) & 0xf) << 16) | (((ioset) & 0xff) << 20))
+
+#define PIN_PA0				0
+#define PIN_PA0__GPIO			PINMUX_PIN(PIN_PA0, 0, 0)
+#define PIN_PA0__SDMMC0_CK		PINMUX_PIN(PIN_PA0, 1, 1)
+#define PIN_PA0__FLEXCOM3_IO0		PINMUX_PIN(PIN_PA0, 2, 1)
+#define PIN_PA0__NWER0			PINMUX_PIN(PIN_PA0, 3, 1)
+
+#define PIN_PA1				1
+#define PIN_PA1__GPIO			PINMUX_PIN(PIN_PA1, 0, 0)
+#define PIN_PA1__SDMMC0_CMD		PINMUX_PIN(PIN_PA1, 1, 1)
+#define PIN_PA1__FLEXCOM3_IO1		PINMUX_PIN(PIN_PA1, 2, 1)
+#define PIN_PA1__A21			PINMUX_PIN(PIN_PA1, 3, 1)
+
+#define PIN_PA2				2
+#define PIN_PA2__GPIO			PINMUX_PIN(PIN_PA2, 0, 0)
+#define PIN_PA2__SDMMC0_RSTN		PINMUX_PIN(PIN_PA2, 1, 1)
+#define PIN_PA2__FLEXCOM3_IO2		PINMUX_PIN(PIN_PA2, 2, 1)
+#define PIN_PA2__A22			PINMUX_PIN(PIN_PA2, 3, 1)
+
+#define PIN_PA3				3
+#define PIN_PA3__GPIO			PINMUX_PIN(PIN_PA3, 0, 0)
+#define PIN_PA3__SDMMC0_DAT0		PINMUX_PIN(PIN_PA3, 1, 1)
+#define PIN_PA3__FLEXCOM3_IO3		PINMUX_PIN(PIN_PA3, 2, 1)
+#define PIN_PA3__D0			PINMUX_PIN(PIN_PA3, 3, 1)
+
+#define PIN_PA4				4
+#define PIN_PA4__GPIO			PINMUX_PIN(PIN_PA4, 0, 0)
+#define PIN_PA4__SDMMC0_DAT1		PINMUX_PIN(PIN_PA4, 1, 1)
+#define PIN_PA4__FLEXCOM3_IO4		PINMUX_PIN(PIN_PA4, 2, 1)
+#define PIN_PA4__D1			PINMUX_PIN(PIN_PA4, 3, 1)
+
+#define PIN_PA5				5
+#define PIN_PA5__GPIO			PINMUX_PIN(PIN_PA5, 0, 0)
+#define PIN_PA5__SDMMC0_DAT4		PINMUX_PIN(PIN_PA5, 1, 1)
+#define PIN_PA5__FLEXCOM2_IO0		PINMUX_PIN(PIN_PA5, 2, 3)
+#define PIN_PA5__D4			PINMUX_PIN(PIN_PA5, 3, 1)
+#define PIN_PA5__TCLK4			PINMUX_PIN(PIN_PA5, 6, 3)
+
+#define PIN_PA6				6
+#define PIN_PA6__GPIO			PINMUX_PIN(PIN_PA6, 0, 0)
+#define PIN_PA6__SDMMC0_DAT5		PINMUX_PIN(PIN_PA6, 1, 1)
+#define PIN_PA6__FLEXCOM2_IO1		PINMUX_PIN(PIN_PA6, 2, 3)
+#define PIN_PA6__D5			PINMUX_PIN(PIN_PA6, 3, 1)
+#define PIN_PA6__TIOB4			PINMUX_PIN(PIN_PA6, 6, 3)
+
+#define PIN_PA7				7
+#define PIN_PA7__GPIO			PINMUX_PIN(PIN_PA7, 0, 0)
+#define PIN_PA7__SDMMC0_DAT6		PINMUX_PIN(PIN_PA7, 1, 1)
+#define PIN_PA7__FLEXCOM2_IO2		PINMUX_PIN(PIN_PA7, 2, 3)
+#define PIN_PA7__D6			PINMUX_PIN(PIN_PA7, 3, 1)
+#define PIN_PA7__TIOA4			PINMUX_PIN(PIN_PA7, 6, 3)
+
+#define PIN_PA8				8
+#define PIN_PA8__GPIO			PINMUX_PIN(PIN_PA8, 0, 0)
+#define PIN_PA8__SDMMC0_DAT7		PINMUX_PIN(PIN_PA8, 1, 1)
+#define PIN_PA8__FLEXCOM2_IO3		PINMUX_PIN(PIN_PA8, 2, 3)
+#define PIN_PA8__D7			PINMUX_PIN(PIN_PA8, 3, 1)
+#define PIN_PA8__TIOA5			PINMUX_PIN(PIN_PA8, 6, 3)
+
+#define PIN_PA9				9
+#define PIN_PA9__GPIO			PINMUX_PIN(PIN_PA9, 0, 0)
+#define PIN_PA9__SDMMC0_DAT2		PINMUX_PIN(PIN_PA9, 1, 1)
+#define PIN_PA9__FLEXCOM0_IO2		PINMUX_PIN(PIN_PA9, 2, 1)
+#define PIN_PA9__D2			PINMUX_PIN(PIN_PA9, 3, 1)
+#define PIN_PA9__TIOB5			PINMUX_PIN(PIN_PA9, 6, 3)
+
+#define PIN_PA10			10
+#define PIN_PA10__GPIO			PINMUX_PIN(PIN_PA10, 0, 0)
+#define PIN_PA10__SDMMC0_DAT3		PINMUX_PIN(PIN_PA10, 1, 1)
+#define PIN_PA10__FLEXCOM0_IO3		PINMUX_PIN(PIN_PA10, 2, 1)
+#define PIN_PA10__D3			PINMUX_PIN(PIN_PA10, 3, 1)
+#define PIN_PA10__TCLK5			PINMUX_PIN(PIN_PA10, 6, 3)
+
+#define PIN_PA11			11
+#define PIN_PA11__GPIO			PINMUX_PIN(PIN_PA11, 0, 0)
+#define PIN_PA11__SDMMC0_DS		PINMUX_PIN(PIN_PA11, 1, 1)
+#define PIN_PA11__FLEXCOM0_IO4		PINMUX_PIN(PIN_PA11, 2, 1)
+#define PIN_PA11__NANDRDY		PINMUX_PIN(PIN_PA11, 3, 1)
+#define PIN_PA11__TIOB3			PINMUX_PIN(PIN_PA11, 6, 3)
+
+#define PIN_PA12			12
+#define PIN_PA12__GPIO			PINMUX_PIN(PIN_PA12, 0, 0)
+#define PIN_PA12__FLEXCOM0_IO0		PINMUX_PIN(PIN_PA12, 2, 1)
+#define PIN_PA12__NRD			PINMUX_PIN(PIN_PA12, 3, 1)
+#define PIN_PA12__PCK0			PINMUX_PIN(PIN_PA12, 4, 1)
+#define PIN_PA12__EXT_IRQ0		PINMUX_PIN(PIN_PA12, 5, 1)
+#define PIN_PA12__TIOA3			PINMUX_PIN(PIN_PA12, 6, 3)
+
+#define PIN_PA13			13
+#define PIN_PA13__GPIO			PINMUX_PIN(PIN_PA13, 0, 0)
+#define PIN_PA13__FLEXCOM0_IO1		PINMUX_PIN(PIN_PA13, 2, 1)
+#define PIN_PA13__NCS0			PINMUX_PIN(PIN_PA13, 3, 1)
+#define PIN_PA13__PCK1			PINMUX_PIN(PIN_PA13, 4, 1)
+#define PIN_PA13__TCLK3			PINMUX_PIN(PIN_PA13, 6, 3)
+
+#define PIN_PA14			14
+#define PIN_PA14__GPIO			PINMUX_PIN(PIN_PA14, 0, 0)
+#define PIN_PA14__FLEXCOM4_IO4		PINMUX_PIN(PIN_PA14, 1, 1)
+#define PIN_PA14__SDMMC0_WP		PINMUX_PIN(PIN_PA14, 2, 1)
+#define PIN_PA14__FLEXCOM3_IO0		PINMUX_PIN(PIN_PA14, 3, 4)
+
+#define PIN_PA15			15
+#define PIN_PA15__GPIO			PINMUX_PIN(PIN_PA15, 0, 0)
+#define PIN_PA15__FLEXCOM4_IO3		PINMUX_PIN(PIN_PA15, 1, 1)
+#define PIN_PA15__SDMMC0_1V8SEL		PINMUX_PIN(PIN_PA15, 2, 1)
+#define PIN_PA15__FLEXCOM3_IO1		PINMUX_PIN(PIN_PA15, 3, 4)
+
+#define PIN_PA16			16
+#define PIN_PA16__GPIO			PINMUX_PIN(PIN_PA16, 0, 0)
+#define PIN_PA16__FLEXCOM4_IO2		PINMUX_PIN(PIN_PA16, 1, 1)
+#define PIN_PA16__SDMMCo_CD		PINMUX_PIN(PIN_PA16, 2, 1)
+#define PIN_PA16__PCK2			PINMUX_PIN(PIN_PA16, 4, 1)
+#define PIN_PA16__EXT_IRQ1		PINMUX_PIN(PIN_PA16, 5, 1)
+
+#define PIN_PA17			17
+#define PIN_PA17__GPIO			PINMUX_PIN(PIN_PA17, 0, 0)
+#define PIN_PA17__FLEXCOM4_IO1		PINMUX_PIN(PIN_PA17, 1, 1)
+
+#define PIN_PA18			18
+#define PIN_PA18__GPIO			PINMUX_PIN(PIN_PA18, 0, 0)
+#define PIN_PA18__FLEXCOM4_IO0		PINMUX_PIN(PIN_PA18, 1, 1)
+
+#define PIN_PA19			19
+#define PIN_PA19__GPIO			PINMUX_PIN(PIN_PA19, 0, 0)
+#define PIN_PA19__TK0			PINMUX_PIN(PIN_PA19, 1, 1)
+#define PIN_PA19__FLEXCOM4_IO5		PINMUX_PIN(PIN_PA19, 3, 1)
+#define PIN_PA19__PWML0			PINMUX_PIN(PIN_PA19, 4, 3)
+
+#define PIN_PA20			20
+#define PIN_PA20__GPIO			PINMUX_PIN(PIN_PA20, 0, 0)
+#define PIN_PA20__TD0			PINMUX_PIN(PIN_PA20, 1, 1)
+#define PIN_PA20__FLEXCOM3_IO4		PINMUX_PIN(PIN_PA20, 2, 2)
+#define PIN_PA20__FLEXCOM4_IO6		PINMUX_PIN(PIN_PA20, 3, 1)
+#define PIN_PA20__PWMH0			PINMUX_PIN(PIN_PA20, 4, 3)
+
+#define PIN_PA21			21
+#define PIN_PA21__GPIO			PINMUX_PIN(PIN_PA21, 0, 0)
+#define PIN_PA21__TF0			PINMUX_PIN(PIN_PA21, 1, 1)
+#define PIN_PA21__FLEXCOM3_IO3		PINMUX_PIN(PIN_PA21, 2, 2)
+#define PIN_PA21__PWML1			PINMUX_PIN(PIN_PA21, 4, 3)
+
+#define PIN_PA22			22
+#define PIN_PA22__GPIO			PINMUX_PIN(PIN_PA22, 0, 0)
+#define PIN_PA22__RD0			PINMUX_PIN(PIN_PA22, 1, 1)
+#define PIN_PA22__FLEXCOM3_IO2		PINMUX_PIN(PIN_PA22, 2, 2)
+#define PIN_PA22__PDMC0_DS1		PINMUX_PIN(PIN_PA22, 3, 1)
+#define PIN_PA22__PWMH1			PINMUX_PIN(PIN_PA22, 4, 3)
+
+#define PIN_PA23			23
+#define PIN_PA23__GPIO			PINMUX_PIN(PIN_PA23, 0, 0)
+#define PIN_PA23__RK0			PINMUX_PIN(PIN_PA23, 1, 1)
+#define PIN_PA23__FLEXCOM3_IO1		PINMUX_PIN(PIN_PA23, 2, 2)
+#define PIN_PA23__PDMC0_CLK		PINMUX_PIN(PIN_PA23, 3, 1)
+#define PIN_PA23__PWML2			PINMUX_PIN(PIN_PA23, 4, 3)
+
+#define PIN_PA24			24
+#define PIN_PA24__GPIO			PINMUX_PIN(PIN_PA24, 0, 0)
+#define PIN_PA24__RF0			PINMUX_PIN(PIN_PA24, 1, 1)
+#define PIN_PA24__FLEXCOM3_IO0		PINMUX_PIN(PIN_PA24, 2, 2)
+#define PIN_PA24__PDMC0_DS0		PINMUX_PIN(PIN_PA24, 3, 1)
+#define PIN_PA24__PWMH2			PINMUX_PIN(PIN_PA24, 4, 3)
+
+#define PIN_PA25			25
+#define PIN_PA25__GPIO			PINMUX_PIN(PIN_PA25, 0, 0)
+#define PIN_PA25__G0_TXCTL		PINMUX_PIN(PIN_PA25, 1, 1)
+#define PIN_PA25__FLEXCOM6_IO2		PINMUX_PIN(PIN_PA25, 2, 1)
+
+#define PIN_PA26			26
+#define PIN_PA26__GPIO			PINMUX_PIN(PIN_PA26, 0, 0)
+#define PIN_PA26__G0_TX0		PINMUX_PIN(PIN_PA26, 1, 1)
+#define PIN_PA26__FLEXCOM6_IO3		PINMUX_PIN(PIN_PA26, 2, 1)
+
+#define PIN_PA27			27
+#define PIN_PA27__GPIO			PINMUX_PIN(PIN_PA27, 0, 0)
+#define PIN_PA27__G0_TX1		PINMUX_PIN(PIN_PA27, 1, 1)
+#define PIN_PA27__FLEXCOM6_IO4		PINMUX_PIN(PIN_PA27, 2, 1)
+
+#define PIN_PA28			28
+#define PIN_PA28__GPIO			PINMUX_PIN(PIN_PA28, 0, 0)
+#define PIN_PA28__G0_RXCTL		PINMUX_PIN(PIN_PA28, 1, 1)
+#define PIN_PA28__FLEXCOM6_IO0		PINMUX_PIN(PIN_PA28, 2, 1)
+
+#define PIN_PA29			29
+#define PIN_PA29__GPIO			PINMUX_PIN(PIN_PA29, 0, 0)
+#define PIN_PA29__G0_RX0		PINMUX_PIN(PIN_PA29, 1, 1)
+#define PIN_PA29__FLEXCOM6_IO1		PINMUX_PIN(PIN_PA29, 2, 1)
+
+#define PIN_PA30			30
+#define PIN_PA30__GPIO			PINMUX_PIN(PIN_PA30, 0, 0)
+#define PIN_PA30__G0_RX1		PINMUX_PIN(PIN_PA30, 1, 1)
+#define PIN_PA30__FLEXCOM8_IO0		PINMUX_PIN(PIN_PA30, 2, 1)
+
+#define PIN_PA31			31
+#define PIN_PA31__GPIO			PINMUX_PIN(PIN_PA31, 0, 0)
+#define PIN_PA31__G0_MDC		PINMUX_PIN(PIN_PA31, 1, 1)
+#define PIN_PA31__FLEXCOM8_IO1		PINMUX_PIN(PIN_PA31, 2, 1)
+
+#define PIN_PB0				32
+#define PIN_PB0__GPIO			PINMUX_PIN(PIN_PB0, 0, 0)
+#define PIN_PB0__G0_MDIO		PINMUX_PIN(PIN_PB0, 1, 1)
+#define PIN_PB0__FLEXCOM8_IO3		PINMUX_PIN(PIN_PB0, 2, 2)
+
+#define PIN_PB1				33
+#define PIN_PB1__GPIO			PINMUX_PIN(PIN_PB1, 0, 0)
+#define PIN_PB1__G0_REFCK		PINMUX_PIN(PIN_PB1, 1, 2)
+#define PIN_PB1__FLEXCOM8_IO2		PINMUX_PIN(PIN_PB1, 2, 1)
+
+#define PIN_PB2				34
+#define PIN_PB2__GPIO			PINMUX_PIN(PIN_PB2, 0, 0)
+#define PIN_PB2__G0_RX2			PINMUX_PIN(PIN_PB2, 1, 1)
+#define PIN_PB2__FLEXCOM8_IO4		PINMUX_PIN(PIN_PB2, 2, 1)
+#define PIN_PB2__G0_RXER		PINMUX_PIN(PIN_PB2, 3, 2)
+#define PIN_PB2__RK0			PINMUX_PIN(PIN_PB2, 4, 2)
+
+#define PIN_PB3				35
+#define PIN_PB3__GPIO			PINMUX_PIN(PIN_PB3, 0, 0)
+#define PIN_PB3__G0_RXCK		PINMUX_PIN(PIN_PB3, 1, 1)
+#define PIN_PB3__FLEXCOM10_IO2		PINMUX_PIN(PIN_PB3, 2, 2)
+#define PIN_PB3__TK0			PINMUX_PIN(PIN_PB3, 4, 2)
+
+#define PIN_PB4				36
+#define PIN_PB4__GPIO			PINMUX_PIN(PIN_PB4, 0, 0)
+#define PIN_PB4__G0_TX2			PINMUX_PIN(PIN_PB4, 1, 1)
+#define PIN_PB4__FLEXCOM10_IO3		PINMUX_PIN(PIN_PB4, 2, 2)
+#define PIN_PB4__TF0			PINMUX_PIN(PIN_PB4, 4, 2)
+
+#define PIN_PB5				37
+#define PIN_PB5__GPIO			PINMUX_PIN(PIN_PB5, 0, 0)
+#define PIN_PB5__G0_TX3			PINMUX_PIN(PIN_PB5, 1, 1)
+#define PIN_PB5__FLEXCOM10_IO4		PINMUX_PIN(PIN_PB5, 2, 1)
+#define PIN_PB5__TD0			PINMUX_PIN(PIN_PB5, 4, 2)
+
+#define PIN_PB6				38
+#define PIN_PB6__GPIO			PINMUX_PIN(PIN_PB6, 0, 0)
+#define PIN_PB6__G0_RX3			PINMUX_PIN(PIN_PB6, 1, 1)
+#define PIN_PB6__FLEXCOM10_IO0		PINMUX_PIN(PIN_PB6, 2, 2)
+#define PIN_PB6__RD0			PINMUX_PIN(PIN_PB6, 4, 2)
+
+#define PIN_PB7				39
+#define PIN_PB7__GPIO			PINMUX_PIN(PIN_PB7, 0, 0)
+#define PIN_PB7__G0_TSUCOMP		PINMUX_PIN(PIN_PB7, 1, 1)
+#define PIN_PB7__FLEXCOM10_IO1		PINMUX_PIN(PIN_PB7, 2, 2)
+#define PIN_PB7__ADTRG			PINMUX_PIN(PIN_PB7, 3, 1)
+#define PIN_PB7__RF0			PINMUX_PIN(PIN_PB7, 4, 2)
+
+#define PIN_PB8				40
+#define PIN_PB8__GPIO			PINMUX_PIN(PIN_PB8, 0, 0)
+#define PIN_PB8__QSPI0_IO3		PINMUX_PIN(PIN_PB8, 1, 1)
+#define PIN_PB8__PCK3			PINMUX_PIN(PIN_PB8, 2, 1)
+#define PIN_PB8__FLEXCOM2_IO1		PINMUX_PIN(PIN_PB8, 4, 2)
+
+#define PIN_PB9				41
+#define PIN_PB9__GPIO			PINMUX_PIN(PIN_PB9, 0, 0)
+#define PIN_PB9__QSPI0_IO2		PINMUX_PIN(PIN_PB9, 1, 1)
+#define PIN_PB9__FLEXCOM2_IO0		PINMUX_PIN(PIN_PB9, 4, 2)
+#define PIN_PB9__PWMEXTRG0		PINMUX_PIN(PIN_PB9, 5, 1)
+
+#define PIN_PB10			42
+#define PIN_PB10__GPIO			PINMUX_PIN(PIN_PB10, 0, 0)
+#define PIN_PB10__QSPI0_IO1		PINMUX_PIN(PIN_PB10, 1, 1)
+#define PIN_PB10__FLEXCOM2_IO4		PINMUX_PIN(PIN_PB10, 4, 2)
+#define PIN_PB10__PWMEXTRG1		PINMUX_PIN(PIN_PB10, 5, 1)
+
+#define PIN_PB11			43
+#define PIN_PB11__GPIO			PINMUX_PIN(PIN_PB11, 0, 0)
+#define PIN_PB11__QSPI0_IO0		PINMUX_PIN(PIN_PB11, 1, 1)
+#define PIN_PB11__FLEXCOM2_IO5		PINMUX_PIN(PIN_PB11, 4, 2)
+#define PIN_PB11__PWML3			PINMUX_PIN(PIN_PB11, 5, 1)
+#define PIN_PB11__TIOB3			PINMUX_PIN(PIN_PB11, 6, 2)
+
+#define PIN_PB12			44
+#define PIN_PB12__GPIO			PINMUX_PIN(PIN_PB12, 0, 0)
+#define PIN_PB12__QSPI0_CS		PINMUX_PIN(PIN_PB12, 1, 1)
+#define PIN_PB12__FLEXCOM2_IO3		PINMUX_PIN(PIN_PB12, 4, 2)
+#define PIN_PB12__PWMFI1		PINMUX_PIN(PIN_PB12, 6, 1)
+#define PIN_PB12__TIOA3			PINMUX_PIN(PIN_PB12, 6, 2)
+
+#define PIN_PB13			45
+#define PIN_PB13__GPIO			PINMUX_PIN(PIN_PB13, 0, 0)
+#define PIN_PB13__QSPI0_SCK		PINMUX_PIN(PIN_PB13, 1, 1)
+#define PIN_PB13__FLEXCOM2_IO2		PINMUX_PIN(PIN_PB13, 4, 2)
+#define PIN_PB13__PWMFI0		PINMUX_PIN(PIN_PB13, 5, 1)
+#define PIN_PB13__TCLK3			PINMUX_PIN(PIN_PB13, 6, 2)
+
+#define PIN_PB14			46
+#define PIN_PB14__GPIO			PINMUX_PIN(PIN_PB14, 0, 0)
+#define PIN_PB14__QSPI0_SCKN		PINMUX_PIN(PIN_PB14, 1, 1)
+#define PIN_PB14__QSPI1_SCK		PINMUX_PIN(PIN_PB14, 2, 1)
+#define PIN_PB14__I2SMCC0_CK		PINMUX_PIN(PIN_PB14, 3, 3)
+#define PIN_PB14__FLEXCOM10_IO5		PINMUX_PIN(PIN_PB14, 4, 1)
+#define PIN_PB14__PWMH3			PINMUX_PIN(PIN_PB14, 5, 1)
+#define PIN_PB14__FLEXCOM2_IO1		PINMUX_PIN(PIN_PB14, 7, 4)
+
+#define PIN_PB15			47
+#define PIN_PB15__GPIO			PINMUX_PIN(PIN_PB15, 0, 0)
+#define PIN_PB15__QSPI0_IO4		PINMUX_PIN(PIN_PB15, 1, 1)
+#define PIN_PB15__QSPI1_IO0		PINMUX_PIN(PIN_PB15, 2, 1)
+#define PIN_PB15__I2SMCC0_WS		PINMUX_PIN(PIN_PB15, 3, 3)
+#define PIN_PB15__FLEXCOM10_IO6		PINMUX_PIN(PIN_PB15, 4, 1)
+#define PIN_PB15__PWML0			PINMUX_PIN(PIN_PB15, 5, 1)
+#define PIN_PB15__TCLK4			PINMUX_PIN(PIN_PB15, 6, 2)
+#define PIN_PB15__FLEXCOM2_IO0		PINMUX_PIN(PIN_PB15, 7, 4)
+
+#define PIN_PB16			48
+#define PIN_PB16__GPIO			PINMUX_PIN(PIN_PB16, 0, 0)
+#define PIN_PB16__QSPI0_IO5		PINMUX_PIN(PIN_PB16, 1, 1)
+#define PIN_PB16__QSPI1_IO1		PINMUX_PIN(PIN_PB16, 2, 1)
+#define PIN_PB16__I2SMCC0_DIN0		PINMUX_PIN(PIN_PB16, 3, 3)
+#define PIN_PB16__FLEXCOM10_IO4		PINMUX_PIN(PIN_PB16, 4, 1)
+#define PIN_PB16__PWMH0			PINMUX_PIN(PIN_PB16, 5, 1)
+#define PIN_PB16__TIOB4			PINMUX_PIN(PIN_PB16, 6, 2)
+
+#define PIN_PB17			49
+#define PIN_PB17__GPIO			PINMUX_PIN(PIN_PB17, 0, 0)
+#define PIN_PB17__QSPI0_IO6		PINMUX_PIN(PIN_PB17, 1, 1)
+#define PIN_PB17__QSPI1_IO2		PINMUX_PIN(PIN_PB17, 2, 1)
+#define PIN_PB17__I2SMCC0_DOUT0		PINMUX_PIN(PIN_PB17, 3, 3)
+#define PIN_PB17__FLEXCOM10_IO3		PINMUX_PIN(PIN_PB17, 4, 1)
+#define PIN_PB17__PWML1			PINMUX_PIN(PIN_PB17, 5, 1)
+#define PIN_PB17__TIOA4			PINMUX_PIN(PIN_PB17, 6, 2)
+
+#define PIN_PB18			50
+#define PIN_PB18__GPIO			PINMUX_PIN(PIN_PB18, 0, 0)
+#define PIN_PB18__QSPI0_IO7		PINMUX_PIN(PIN_PB18, 1, 1)
+#define PIN_PB18__QSPI1_IO3		PINMUX_PIN(PIN_PB18, 2, 1)
+#define PIN_PB18__I2SMCC0_MCK		PINMUX_PIN(PIN_PB18, 3, 3)
+#define PIN_PB18__FLEXCOM10_IO2		PINMUX_PIN(PIN_PB18, 4, 1)
+#define PIN_PB18__PWMH1			PINMUX_PIN(PIN_PB18, 5, 1)
+#define PIN_PB18__TIOA5			PINMUX_PIN(PIN_PB18, 6, 2)
+
+#define PIN_PB19			51
+#define PIN_PB19__GPIO			PINMUX_PIN(PIN_PB19, 0, 0)
+#define PIN_PB19__QSPI0_DQS		PINMUX_PIN(PIN_PB19, 1, 1)
+#define PIN_PB19__EXT_IRQ1		PINMUX_PIN(PIN_PB19, 2, 2)
+#define PIN_PB19__PCK4			PINMUX_PIN(PIN_PB19, 3, 1)
+#define PIN_PB19__FLEXCOM10_IO1		PINMUX_PIN(PIN_PB19, 4, 1)
+#define PIN_PB19__PWML2			PINMUX_PIN(PIN_PB19, 5, 1)
+#define PIN_PB19__TIOB5			PINMUX_PIN(PIN_PB19, 6, 2)
+
+#define PIN_PB20			52
+#define PIN_PB20__GPIO			PINMUX_PIN(PIN_PB20, 0, 0)
+#define PIN_PB20__QSPI0_INT		PINMUX_PIN(PIN_PB20, 1, 1)
+#define PIN_PB20__QSPI1_CS		PINMUX_PIN(PIN_PB20, 2, 1)
+#define PIN_PB20__FLEXCOM10_IO0		PINMUX_PIN(PIN_PB20, 4, 1)
+#define PIN_PB20__PWMH2			PINMUX_PIN(PIN_PB20, 5, 1)
+#define PIN_PB20__TCLK5			PINMUX_PIN(PIN_PB20, 6, 2)
+
+#define PIN_PB21			53
+#define PIN_PB21__GPIO			PINMUX_PIN(PIN_PB21, 0, 0)
+#define PIN_PB21__SDMMC1_RSTN		PINMUX_PIN(PIN_PB21, 1, 1)
+#define PIN_PB21__FLEXCOM6_IO4		PINMUX_PIN(PIN_PB21, 2, 2)
+#define PIN_PB21__TIOB2			PINMUX_PIN(PIN_PB21, 3, 2)
+#define PIN_PB21__ADTRG			PINMUX_PIN(PIN_PB21, 4, 2)
+#define PIN_PB21__EXT_IRQ0		PINMUX_PIN(PIN_PB21, 5, 2)
+
+#define PIN_PB22			54
+#define PIN_PB22__GPIO			PINMUX_PIN(PIN_PB22, 0, 0)
+#define PIN_PB22__SDMMC1_CMD		PINMUX_PIN(PIN_PB22, 1, 1)
+#define PIN_PB22__FLEXCOM6_IO3		PINMUX_PIN(PIN_PB22, 2, 2)
+#define PIN_PB22__TCLK2			PINMUX_PIN(PIN_PB22, 3, 2)
+
+#define PIN_PB23			55
+#define PIN_PB23__GPIO			PINMUX_PIN(PIN_PB23, 0, 0)
+#define PIN_PB23__SDMMC1_CK		PINMUX_PIN(PIN_PB23, 1, 1)
+#define PIN_PB23__FLEXCOM6_IO2		PINMUX_PIN(PIN_PB23, 2, 2)
+#define PIN_PB23__TIOA2			PINMUX_PIN(PIN_PB23, 3, 2)
+
+#define PIN_PB24			56
+#define PIN_PB24__GPIO			PINMUX_PIN(PIN_PB24, 0, 0)
+#define PIN_PB24__SDMMC1_DAT0		PINMUX_PIN(PIN_PB24, 1, 1)
+#define PIN_PB24__FLEXCOM6_IO0		PINMUX_PIN(PIN_PB24, 2, 2)
+
+#define PIN_PB25			57
+#define PIN_PB25__GPIO			PINMUX_PIN(PIN_PB25, 0, 0)
+#define PIN_PB25__SDMMC1_DAT1		PINMUX_PIN(PIN_PB25, 1, 1)
+#define PIN_PB25__FLEXCOM6_IO1		PINMUX_PIN(PIN_PB25, 2, 2)
+#define PIN_PB25__TIOB2			PINMUX_PIN(PIN_PB25, 3, 1)
+
+#define PIN_PB26			58
+#define PIN_PB26__GPIO			PINMUX_PIN(PIN_PB26, 0, 0)
+#define PIN_PB26__SDMMC1_DAT2		PINMUX_PIN(PIN_PB26, 1, 1)
+#define PIN_PB26__FLEXCOM8_IO0		PINMUX_PIN(PIN_PB26, 2, 3)
+#define PIN_PB26__TCLK2			PINMUX_PIN(PIN_PB26, 3, 1)
+
+#define PIN_PB27			59
+#define PIN_PB27__GPIO			PINMUX_PIN(PIN_PB27, 0, 0)
+#define PIN_PB27__SDMMC1_DAT3		PINMUX_PIN(PIN_PB27, 1, 1)
+#define PIN_PB27__FLEXCOM8_IO1		PINMUX_PIN(PIN_PB27, 2, 3)
+#define PIN_PB27__TIOA2			PINMUX_PIN(PIN_PB27, 3, 1)
+
+#define PIN_PB28			60
+#define PIN_PB28__GPIO			PINMUX_PIN(PIN_PB28, 0, 0)
+#define PIN_PB28__SDMMC1_WP		PINMUX_PIN(PIN_PB28, 1, 1)
+#define PIN_PB28__FLEXCOM1_IO0		PINMUX_PIN(PIN_PB28, 3, 3)
+#define PIN_PB28__D15			PINMUX_PIN(PIN_PB28, 5, 1)
+
+#define PIN_PB29			61
+#define PIN_PB29__GPIO			PINMUX_PIN(PIN_PB29, 0, 0)
+#define PIN_PB29__SDMMC1_CD		PINMUX_PIN(PIN_PB29, 1, 1)
+#define PIN_PB29__I2SMCC0_MCK		PINMUX_PIN(PIN_PB29, 2, 1)
+#define PIN_PB29__FLEXCOM1_IO1		PINMUX_PIN(PIN_PB29, 3, 3)
+#define PIN_PB29__D14			PINMUX_PIN(PIN_PB29, 5, 2)
+
+#define PIN_PB30			62
+#define PIN_PB30__GPIO			PINMUX_PIN(PIN_PB30, 0, 0)
+#define PIN_PB30__SDMMC1_1V8SEL		PINMUX_PIN(PIN_PB30, 1, 1)
+#define PIN_PB30__I2SMCC1_MCK		PINMUX_PIN(PIN_PB30, 2, 2)
+#define PIN_PB30__FLEXCOM1_IO2		PINMUX_PIN(PIN_PB30, 3, 3)
+#define PIN_PB30__TIOA1			PINMUX_PIN(PIN_PB30, 4, 1)
+#define PIN_PB30__NCS1			PINMUX_PIN(PIN_PB30, 5, 1)
+
+#define PIN_PB31			63
+#define PIN_PB31__GPIO			PINMUX_PIN(PIN_PB31, 0, 0)
+#define PIN_PB31__PCK7			PINMUX_PIN(PIN_PB31, 1, 2)
+#define PIN_PB31__I2SMCC1_DIN1		PINMUX_PIN(PIN_PB31, 2, 1)
+#define PIN_PB31__FLEXCOM1_IO3		PINMUX_PIN(PIN_PB31, 3, 3)
+#define PIN_PB31__TCLK1			PINMUX_PIN(PIN_PB31, 4, 1)
+#define PIN_PB31__NWE			PINMUX_PIN(PIN_PB31, 5, 2)
+
+#define PIN_PC0				64
+#define PIN_PC0__GPIO			PINMUX_PIN(PIN_PC0, 0, 0)
+#define PIN_PC0__PCK6			PINMUX_PIN(PIN_PC0, 1, 2)
+#define PIN_PC0__I2SMCC1_DIN2		PINMUX_PIN(PIN_PC0, 2, 1)
+#define PIN_PC0__FLEXCOM9_IO4		PINMUX_PIN(PIN_PC0, 3, 2)
+#define PIN_PC0__TIOB1			PINMUX_PIN(PIN_PC0, 4, 1)
+#define PIN_PC0__NWR1			PINMUX_PIN(PIN_PC0, 5, 1)
+
+#define PIN_PC1				65
+#define PIN_PC1__GPIO			PINMUX_PIN(PIN_PC1, 0, 0)
+#define PIN_PC1__PCK5			PINMUX_PIN(PIN_PC1, 1, 1)
+#define PIN_PC1__FLEXCOM9_IO2		PINMUX_PIN(PIN_PC1, 3, 2)
+#define PIN_PC1__SMCK			PINMUX_PIN(PIN_PC1, 5, 1)
+
+#define PIN_PC2				66
+#define PIN_PC2__GPIO			PINMUX_PIN(PIN_PC2, 0, 0)
+#define PIN_PC2__EXT_IRQ0		PINMUX_PIN(PIN_PC2, 1, 3)
+#define PIN_PC2__FLEXCOM9_IO3		PINMUX_PIN(PIN_PC2, 3, 2)
+#define PIN_PC2__A11			PINMUX_PIN(PIN_PC2, 5, 1)
+
+#define PIN_PC3				67
+#define PIN_PC3__GPIO			PINMUX_PIN(PIN_PC3, 0, 0)
+#define PIN_PC3__SPDIF_RX		PINMUX_PIN(PIN_PC3, 1, 2)
+#define PIN_PC3__FLEXCOM9_IO0		PINMUX_PIN(PIN_PC3, 3, 2)
+#define PIN_PC3__FLEXCOM0_IO4		PINMUX_PIN(PIN_PC3, 4, 2)
+#define PIN_PC3__A10			PINMUX_PIN(PIN_PC3, 5, 1)
+
+#define PIN_PC4				68
+#define PIN_PC4__GPIO			PINMUX_PIN(PIN_PC4, 0, 0)
+#define PIN_PC4__SPDIF_TX		PINMUX_PIN(PIN_PC4, 1, 2)
+#define PIN_PC4__FLEXCOM9_IO1		PINMUX_PIN(PIN_PC4, 3, 2)
+#define PIN_PC4__FLEXCOM0_IO3		PINMUX_PIN(PIN_PC4, 4, 2)
+#define PIN_PC4__D0			PINMUX_PIN(PIN_PC4, 5, 2)
+
+#define PIN_PC5				69
+#define PIN_PC5__GPIO			PINMUX_PIN(PIN_PC5, 0, 0)
+#define PIN_PC5__I3CC_SDASPUE		PINMUX_PIN(PIN_PC5, 1, 1)
+#define PIN_PC5__I2SMCC1_DIN3		PINMUX_PIN(PIN_PC5, 2, 1)
+#define PIN_PC5__FLEXCOM0_IO2		PINMUX_PIN(PIN_PC5, 4, 2)
+#define PIN_PC5__D1			PINMUX_PIN(PIN_PC5, 5, 2)
+
+#define PIN_PC6				70
+#define PIN_PC6__GPIO			PINMUX_PIN(PIN_PC6, 0, 0)
+#define PIN_PC6__I3CC_SCL		PINMUX_PIN(PIN_PC6, 1, 1)
+#define PIN_PC6__FLEXCOM0_IO1		PINMUX_PIN(PIN_PC6, 4, 2)
+#define PIN_PC6__D4			PINMUX_PIN(PIN_PC6, 5, 2)
+
+#define PIN_PC7				71
+#define PIN_PC7__GPIO			PINMUX_PIN(PIN_PC7, 0, 0)
+#define PIN_PC7__I3CC_SDA		PINMUX_PIN(PIN_PC7, 1, 1)
+#define PIN_PC7__FLEXCOM0_IO0		PINMUX_PIN(PIN_PC7, 4, 2)
+#define PIN_PC7__D5			PINMUX_PIN(PIN_PC7, 5, 2)
+
+#define PIN_PC8				72
+#define PIN_PC8__GPIO			PINMUX_PIN(PIN_PC8, 0, 0)
+#define PIN_PC8__I2SMCC0_DIN1		PINMUX_PIN(PIN_PC8, 1, 1)
+#define PIN_PC8__PDMC0_DS1		PINMUX_PIN(PIN_PC8, 2, 2)
+#define PIN_PC8__I2SMCC1_DOUT1		PINMUX_PIN(PIN_PC8, 3, 1)
+#define PIN_PC8__FLEXCOM9_IO0		PINMUX_PIN(PIN_PC8, 4, 1)
+#define PIN_PC8__D6			PINMUX_PIN(PIN_PC8, 5, 2)
+
+#define PIN_PC9				73
+#define PIN_PC9__GPIO			PINMUX_PIN(PIN_PC9, 0, 0)
+#define PIN_PC9__I2SMCC0_DIN2		PINMUX_PIN(PIN_PC9, 1, 1)
+#define PIN_PC9__PDMC0_CLK		PINMUX_PIN(PIN_PC9, 2, 2)
+#define PIN_PC9__I2SMCC1_DOUT2		PINMUX_PIN(PIN_PC9, 3, 1)
+#define PIN_PC9__FLEXCOM9_IO1		PINMUX_PIN(PIN_PC9, 4, 1)
+#define PIN_PC9__D7			PINMUX_PIN(PIN_PC9, 5, 2)
+
+#define PIN_PC10			74
+#define PIN_PC10__GPIO			PINMUX_PIN(PIN_PC10, 0, 0)
+#define PIN_PC10__I2SMCC0_DIN3		PINMUX_PIN(PIN_PC10, 1, 1)
+#define PIN_PC10__PDMC0_DS0		PINMUX_PIN(PIN_PC10, 2, 2)
+#define PIN_PC10__I2SMCC1_DOUT3		PINMUX_PIN(PIN_PC10, 3, 1)
+#define PIN_PC10__FLEXCOM9_IO2		PINMUX_PIN(PIN_PC10, 4, 1)
+#define PIN_PC10__D2			PINMUX_PIN(PIN_PC10, 5, 2)
+
+#define PIN_PC11			75
+#define PIN_PC11__GPIO			PINMUX_PIN(PIN_PC11, 0, 0)
+#define PIN_PC11__I2SMCC0_DOUT1		PINMUX_PIN(PIN_PC11, 1, 1)
+#define PIN_PC11__PDMC1_DS0		PINMUX_PIN(PIN_PC11, 2, 1)
+#define PIN_PC11__FLEXCOM9_IO3		PINMUX_PIN(PIN_PC11, 4, 1)
+#define PIN_PC10__D3			PINMUX_PIN(PIN_PC10, 5, 2)
+
+#define PIN_PC12			76
+#define PIN_PC12__GPIO			PINMUX_PIN(PIN_PC12, 0, 0)
+#define PIN_PC12__I2SMCC0_DOUT2		PINMUX_PIN(PIN_PC12, 1, 1)
+#define PIN_PC12__PDMC1_CLK		PINMUX_PIN(PIN_PC12, 2, 1)
+#define PIN_PC12__FLEXCOM9_IO4		PINMUX_PIN(PIN_PC12, 4, 1)
+#define PIN_PC12__A9			PINMUX_PIN(PIN_PC12, 5, 1)
+
+#define PIN_PC13			77
+#define PIN_PC13__GPIO			PINMUX_PIN(PIN_PC13, 0, 0)
+#define PIN_PC13__I2SMCC0_DOUT3		PINMUX_PIN(PIN_PC13, 1, 1)
+#define PIN_PC13__PDMC1_DS1		PINMUX_PIN(PIN_PC13, 2, 1)
+#define PIN_PC13__A8			PINMUX_PIN(PIN_PC13, 5, 1)
+
+#define PIN_PC14			78
+#define PIN_PC14__GPIO			PINMUX_PIN(PIN_PC14, 0, 0)
+#define PIN_PC14__I2SMCC1_DIN0		PINMUX_PIN(PIN_PC14, 1, 1)
+#define PIN_PC14__SPDIF_RX		PINMUX_PIN(PIN_PC14, 2, 3)
+#define PIN_PC14__FLEXCOM1_IO0		PINMUX_PIN(PIN_PC14, 3, 2)
+#define PIN_PC14__A7			PINMUX_PIN(PIN_PC14, 5, 1)
+
+#define PIN_PC15			79
+#define PIN_PC15__GPIO			PINMUX_PIN(PIN_PC15, 0, 0)
+#define PIN_PC15__I2SMCC1_WS		PINMUX_PIN(PIN_PC15, 1, 1)
+#define PIN_PC15__PDMC1_DS1		PINMUX_PIN(PIN_PC15, 2, 2)
+#define PIN_PC15__FLEXCOM1_IO1		PINMUX_PIN(PIN_PC15, 3, 2)
+#define PIN_PC15__A6			PINMUX_PIN(PIN_PC15, 5, 1)
+
+#define PIN_PC16			80
+#define PIN_PC16__GPIO			PINMUX_PIN(PIN_PC16, 0, 0)
+#define PIN_PC16__I2SMCC1_CK		PINMUX_PIN(PIN_PC16, 1, 1)
+#define PIN_PC16__PDMC1_CLK		PINMUX_PIN(PIN_PC16, 2, 2)
+#define PIN_PC16__FLEXCOM1_IO2		PINMUX_PIN(PIN_PC16, 3, 2)
+#define PIN_PC16__TIOA1			PINMUX_PIN(PIN_PC16, 4, 2)
+#define PIN_PC16__A5			PINMUX_PIN(PIN_PC16, 5, 1)
+
+#define PIN_PC17			81
+#define PIN_PC17__GPIO			PINMUX_PIN(PIN_PC17, 0, 0)
+#define PIN_PC17__I2SMCC1_DOUT0		PINMUX_PIN(PIN_PC17, 1, 1)
+#define PIN_PC17__PDMC1_DS0		PINMUX_PIN(PIN_PC17, 2, 2)
+#define PIN_PC17__FLEXCOM1_IO3		PINMUX_PIN(PIN_PC17, 3, 2)
+#define PIN_PC17__TCLK1			PINMUX_PIN(PIN_PC17, 4, 2)
+#define PIN_PC17__A4			PINMUX_PIN(PIN_PC17, 5, 1)
+
+#define PIN_PC18			82
+#define PIN_PC18__GPIO			PINMUX_PIN(PIN_PC18, 0, 0)
+#define PIN_PC18__I2SMCC0_DIN0		PINMUX_PIN(PIN_PC18, 1, 1)
+#define PIN_PC18__SPDIF_TX		PINMUX_PIN(PIN_PC18, 2, 3)
+#define PIN_PC18__FLEXCOM1_IO4		PINMUX_PIN(PIN_PC18, 3, 2)
+#define PIN_PC18__TIOB1			PINMUX_PIN(PIN_PC18, 4, 2)
+#define PIN_PC18__A3			PINMUX_PIN(PIN_PC18, 5, 1)
+
+#define PIN_PC19			83
+#define PIN_PC19__GPIO			PINMUX_PIN(PIN_PC19, 0, 0)
+#define PIN_PC19__I2SMCC0_WS		PINMUX_PIN(PIN_PC19, 1, 1)
+#define PIN_PC19__PCK6			PINMUX_PIN(PIN_PC19, 2, 1)
+#define PIN_PC19__A2			PINMUX_PIN(PIN_PC19, 5, 1)
+
+#define PIN_PC20			84
+#define PIN_PC20__GPIO			PINMUX_PIN(PIN_PC20, 0, 0)
+#define PIN_PC20__I2SMCC0_DOUT0		PINMUX_PIN(PIN_PC20, 1, 1)
+#define PIN_PC20__A1			PINMUX_PIN(PIN_PC20, 5, 1)
+
+#define PIN_PC21			85
+#define PIN_PC21__GPIO			PINMUX_PIN(PIN_PC21, 0, 0)
+#define PIN_PC21__I2SMCC0_CK		PINMUX_PIN(PIN_PC21, 1, 1)
+#define PIN_PC21__PCK7			PINMUX_PIN(PIN_PC21, 2, 1)
+#define PIN_PC21__A0			PINMUX_PIN(PIN_PC21, 5, 1)
+
+#define PIN_PC22			86
+#define PIN_PC22__GPIO			PINMUX_PIN(PIN_PC22, 0, 0)
+#define PIN_PC22__NTRST			PINMUX_PIN(PIN_PC22, 1, 1)
+#define PIN_PC22__NWAIT			PINMUX_PIN(PIN_PC22, 5, 1)
+
+#define PIN_PC23			87
+#define PIN_PC23__GPIO			PINMUX_PIN(PIN_PC23, 0, 0)
+#define PIN_PC23__TCK_SWCLK		PINMUX_PIN(PIN_PC23, 1, 1)
+
+#define PIN_PC24			88
+#define PIN_PC24__GPIO			PINMUX_PIN(PIN_PC24, 0, 0)
+#define PIN_PC24__TMS_SWDIO		PINMUX_PIN(PIN_PC24, 1, 1)
+
+#define PIN_PC25			89
+#define PIN_PC25__GPIO			PINMUX_PIN(PIN_PC25, 0, 0)
+#define PIN_PC25__TDI			PINMUX_PIN(PIN_PC25, 1, 1)
+
+#define PIN_PC26			90
+#define PIN_PC26__GPIO			PINMUX_PIN(PIN_PC26, 0, 0)
+#define PIN_PC26__TDO			PINMUX_PIN(PIN_PC26, 1, 1)
+#define PIN_PC26__A15			PINMUX_PIN(PIN_PC26, 5, 1)
+
+#define PIN_PC27			91
+#define PIN_PC27__GPIO			PINMUX_PIN(PIN_PC27, 0, 0)
+#define PIN_PC27__SDMMC2_CMD		PINMUX_PIN(PIN_PC27, 1, 1)
+#define PIN_PC27__FLEXCOM8_IO0		PINMUX_PIN(PIN_PC27, 2, 2)
+#define PIN_PC27__TD1			PINMUX_PIN(PIN_PC27, 4, 2)
+#define PIN_PC27__D8			PINMUX_PIN(PIN_PC27, 5, 1)
+
+#define PIN_PC28			92
+#define PIN_PC28__GPIO			PINMUX_PIN(PIN_PC28, 0, 0)
+#define PIN_PC28__SDMMC2_CK		PINMUX_PIN(PIN_PC28, 1, 1)
+#define PIN_PC28__FLEXCOM8_IO1		PINMUX_PIN(PIN_PC28, 2, 2)
+#define PIN_PC28__TF1			PINMUX_PIN(PIN_PC28, 4, 2)
+#define PIN_PC28__D9			PINMUX_PIN(PIN_PC28, 5, 1)
+
+#define PIN_PC29			93
+#define PIN_PC29__GPIO			PINMUX_PIN(PIN_PC29, 0, 0)
+#define PIN_PC29__SDMMC2_DAT0		PINMUX_PIN(PIN_PC29, 1, 1)
+#define PIN_PC29__FLEXCOM8_IO2		PINMUX_PIN(PIN_PC29, 2, 2)
+#define PIN_PC29__TK1			PINMUX_PIN(PIN_PC29, 4, 2)
+#define PIN_PC29__D10			PINMUX_PIN(PIN_PC29, 5, 1)
+#define PIN_PC29__TCLK0			PINMUX_PIN(PIN_PC29, 6, 1)
+
+#define PIN_PC30			94
+#define PIN_PC30__GPIO			PINMUX_PIN(PIN_PC30, 0, 0)
+#define PIN_PC30__SDMMC2_DAT1		PINMUX_PIN(PIN_PC30, 1, 1)
+#define PIN_PC30__FLEXCOM8_IO3		PINMUX_PIN(PIN_PC30, 2, 2)
+#define PIN_PC30__RD1			PINMUX_PIN(PIN_PC30, 4, 2)
+#define PIN_PC30__D11			PINMUX_PIN(PIN_PC30, 5, 1)
+#define PIN_PC30__TIOA0			PINMUX_PIN(PIN_PC30, 6, 1)
+
+#define PIN_PC31			95
+#define PIN_PC31__GPIO			PINMUX_PIN(PIN_PC31, 0, 0)
+#define PIN_PC31__SDMMC2_DAT2		PINMUX_PIN(PIN_PC31, 1, 1)
+#define PIN_PC31__FLEXCOM8_IO4		PINMUX_PIN(PIN_PC31, 2, 2)
+#define PIN_PC31__PCK0			PINMUX_PIN(PIN_PC31, 3, 2)
+#define PIN_PC31__RK1			PINMUX_PIN(PIN_PC31, 4, 2)
+#define PIN_PC31__D12			PINMUX_PIN(PIN_PC31, 5, 1)
+#define PIN_PC31__TIOB0			PINMUX_PIN(PIN_PC31, 6, 1)
+
+#define PIN_PD0				96
+#define PIN_PD0__GPIO			PINMUX_PIN(PIN_PD0, 0, 0)
+#define PIN_PD0__SDMMC2_DAT3		PINMUX_PIN(PIN_PD0, 1, 1)
+#define PIN_PD0__PCK1			PINMUX_PIN(PIN_PD0, 3, 2)
+#define PIN_PD0__RF1			PINMUX_PIN(PIN_PD0, 4, 2)
+#define PIN_PD0__D13			PINMUX_PIN(PIN_PD0, 5, 1)
+
+#define PIN_PD1				97
+#define PIN_PD1__GPIO			PINMUX_PIN(PIN_PD1, 0, 0)
+#define PIN_PD1__SDMMC2_WP		PINMUX_PIN(PIN_PD1, 1, 1)
+#define PIN_PD1__FLEXCOM1_IO5		PINMUX_PIN(PIN_PD1, 2, 1)
+#define PIN_PD1__LCDC_HSYNC		PINMUX_PIN(PIN_PD1, 3, 2)
+#define PIN_PD1__FLEXCOM3_IO0		PINMUX_PIN(PIN_PD1, 4, 3)
+
+#define PIN_PD2				98
+#define PIN_PD2__GPIO			PINMUX_PIN(PIN_PD2, 0, 0)
+#define PIN_PD2__SDMMC2_CD		PINMUX_PIN(PIN_PD2, 1, 1)
+#define PIN_PD2__FLEXCOM1_IO6		PINMUX_PIN(PIN_PD2, 2, 1)
+#define PIN_PD2__LCDC_VSYNC		PINMUX_PIN(PIN_PD2, 3, 2)
+#define PIN_PD2__FLEXCOM3_IO1		PINMUX_PIN(PIN_PD2, 4, 3)
+
+#define PIN_PD3				99
+#define PIN_PD3__GPIO			PINMUX_PIN(PIN_PD3, 0, 0)
+#define PIN_PD3__SDMMC2_1V8SEL		PINMUX_PIN(PIN_PD3, 1, 1)
+#define PIN_PD3__FLEXCOM1_IO4		PINMUX_PIN(PIN_PD3, 2, 1)
+#define PIN_PD3__TIOA0			PINMUX_PIN(PIN_PD3, 3, 2)
+#define PIN_PD3__FLEXCOM3_IO2		PINMUX_PIN(PIN_PD3, 4, 3)
+#define PIN_PD3__EXT_IRQ1		PINMUX_PIN(PIN_PD3, 5, 3)
+
+#define PIN_PD4				100
+#define PIN_PD4__GPIO			PINMUX_PIN(PIN_PD4, 0, 0)
+#define PIN_PD4__LCDC_HSYNC		PINMUX_PIN(PIN_PD4, 1, 1)
+#define PIN_PD4__FLEXCOM1_IO2		PINMUX_PIN(PIN_PD4, 2, 1)
+#define PIN_PD4__TIOB0			PINMUX_PIN(PIN_PD4, 3, 2)
+#define PIN_PD4__FLEXCOM7_IO1		PINMUX_PIN(PIN_PD4, 4, 3)
+
+#define PIN_PD5				101
+#define PIN_PD5__GPIO			PINMUX_PIN(PIN_PD5, 0, 0)
+#define PIN_PD5__LCDC_VSYNC		PINMUX_PIN(PIN_PD5, 1, 1)
+#define PIN_PD5__FLEXCOM1_IO3		PINMUX_PIN(PIN_PD5, 2, 1)
+#define PIN_PD5__TCLK0			PINMUX_PIN(PIN_PD5, 3, 2)
+#define PIN_PD5__FLEXCOM7_IO0		PINMUX_PIN(PIN_PD5, 4, 3)
+
+#define PIN_PD6				102
+#define PIN_PD6__GPIO			PINMUX_PIN(PIN_PD6, 0, 0)
+#define PIN_PD6__LCDC_PWM		PINMUX_PIN(PIN_PD6, 1, 1)
+#define PIN_PD6__FLEXCOM1_IO1		PINMUX_PIN(PIN_PD6, 2, 1)
+#define PIN_PD6__FLEXCOM7_IO2		PINMUX_PIN(PIN_PD6, 4, 3)
+
+#define PIN_PD7				103
+#define PIN_PD7__GPIO			PINMUX_PIN(PIN_PD7, 0, 0)
+#define PIN_PD7__LCDC_DISP		PINMUX_PIN(PIN_PD7, 1, 1)
+#define PIN_PD7__FLEXCOM1_IO0		PINMUX_PIN(PIN_PD7, 2, 1)
+#define PIN_PD7__FLEXCOM7_IO3		PINMUX_PIN(PIN_PD7, 4, 3)
+
+#define PIN_PD8				104
+#define PIN_PD8__GPIO			PINMUX_PIN(PIN_PD8, 0, 0)
+#define PIN_PD8__CANTX0			PINMUX_PIN(PIN_PD8, 1, 1)
+#define PIN_PD8__FLEXCOM7_IO0		PINMUX_PIN(PIN_PD8, 2, 1)
+
+#define PIN_PD9				105
+#define PIN_PD9__GPIO			PINMUX_PIN(PIN_PD9, 0, 0)
+#define PIN_PD9__CANRX0			PINMUX_PIN(PIN_PD9, 1, 1)
+#define PIN_PD9__FLEXCOM7_IO1		PINMUX_PIN(PIN_PD9, 2, 1)
+
+#define PIN_PD10			106
+#define PIN_PD10__GPIO			PINMUX_PIN(PIN_PD10, 0, 0)
+#define PIN_PD10__CANTX1		PINMUX_PIN(PIN_PD10, 1, 1)
+#define PIN_PD10__FLEXCOM7_IO2		PINMUX_PIN(PIN_PD10, 2, 1)
+#define PIN_PD10__TIOA1			PINMUX_PIN(PIN_PD10, 3, 3)
+
+#define PIN_PD11			107
+#define PIN_PD11__GPIO			PINMUX_PIN(PIN_PD11, 0, 0)
+#define PIN_PD11__CANRX1		PINMUX_PIN(PIN_PD11, 1, 1)
+#define PIN_PD11__FLEXCOM7_IO3		PINMUX_PIN(PIN_PD11, 2, 1)
+#define PIN_PD11__TCLK1			PINMUX_PIN(PIN_PD11, 3, 3)
+
+#define PIN_PD12			108
+#define PIN_PD12__GPIO			PINMUX_PIN(PIN_PD12, 0, 0)
+#define PIN_PD12__CANTX2		PINMUX_PIN(PIN_PD12, 1, 1)
+#define PIN_PD12__FLEXCOM7_IO4		PINMUX_PIN(PIN_PD12, 2, 1)
+#define PIN_PD12__TIOB1			PINMUX_PIN(PIN_PD12, 3, 3)
+#define PIN_PD12__PCK2			PINMUX_PIN(PIN_PD12, 4, 2)
+#define PIN_PD12__FLEXCOM3_IO3		PINMUX_PIN(PIN_PD12, 5, 3)
+
+#define PIN_PD13			109
+#define PIN_PD13__GPIO			PINMUX_PIN(PIN_PD13, 0, 0)
+#define PIN_PD13__CANRX2		PINMUX_PIN(PIN_PD13, 1, 1)
+#define PIN_PD13__FLEXCOM5_IO4		PINMUX_PIN(PIN_PD13, 2, 1)
+#define PIN_PD13__TIOA2			PINMUX_PIN(PIN_PD13, 3, 3)
+#define PIN_PD13__PCK3			PINMUX_PIN(PIN_PD13, 4, 2)
+
+#define PIN_PD14			110
+#define PIN_PD14__GPIO			PINMUX_PIN(PIN_PD14, 0, 0)
+#define PIN_PD14__CANTX3		PINMUX_PIN(PIN_PD14, 1, 1)
+#define PIN_PD14__FLEXCOM5_IO2		PINMUX_PIN(PIN_PD14, 2, 1)
+#define PIN_PD14__TIOB2			PINMUX_PIN(PIN_PD14, 3, 3)
+
+#define PIN_PD15			111
+#define PIN_PD15__GPIO			PINMUX_PIN(PIN_PD15, 0, 0)
+#define PIN_PD15__CANRX3		PINMUX_PIN(PIN_PD15, 1, 1)
+#define PIN_PD15__FLEXCOM5_IO3		PINMUX_PIN(PIN_PD15, 2, 1)
+#define PIN_PD15__TCLK2			PINMUX_PIN(PIN_PD15, 3, 3)
+
+#define PIN_PD16			112
+#define PIN_PD16__GPIO			PINMUX_PIN(PIN_PD16, 0, 0)
+#define PIN_PD16__CANTX4		PINMUX_PIN(PIN_PD16, 1, 1)
+#define PIN_PD16__FLEXCOM5_IO0		PINMUX_PIN(PIN_PD16, 2, 1)
+
+#define PIN_PD17			113
+#define PIN_PD17__GPIO			PINMUX_PIN(PIN_PD17, 0, 0)
+#define PIN_PD17__CANRX4		PINMUX_PIN(PIN_PD17, 1, 1)
+#define PIN_PD17__FLEXCOM5_IO1		PINMUX_PIN(PIN_PD17, 2, 1)
+
+#define PIN_PD18			114
+#define PIN_PD18__GPIO			PINMUX_PIN(PIN_PD18, 0, 0)
+#define PIN_PD18__FLEXCOM6_IO0		PINMUX_PIN(PIN_PD18, 2, 4)
+#define PIN_PD18__CANTX1		PINMUX_PIN(PIN_PD18, 3, 2)
+#define PIN_PD18__PCK4			PINMUX_PIN(PIN_PD18, 4, 2)
+
+#define PIN_PD19			115
+#define PIN_PD19__GPIO			PINMUX_PIN(PIN_PD19, 0, 0)
+#define PIN_PD19__FLEXCOM6_IO1		PINMUX_PIN(PIN_PD19, 2, 4)
+#define PIN_PD19__CANRX1		PINMUX_PIN(PIN_PD19, 3, 2)
+#define PIN_PD19__PCK2			PINMUX_PIN(PIN_PD19, 4, 3)
+
+#define PIN_PD20			116
+#define PIN_PD20__GPIO			PINMUX_PIN(PIN_PD20, 0, 0)
+#define PIN_PD20__PFLEXCOM6_IO2		PINMUX_PIN(PIN_PD20, 2, 4)
+#define PIN_PD20__I2SMCC1_MCK		PINMUX_PIN(PIN_PD20, 3, 2)
+#define PIN_PD20__PCK3			PINMUX_PIN(PIN_PD20, 4, 3)
+
+#define PIN_PD21			117
+#define PIN_PD21__GPIO			PINMUX_PIN(PIN_PD21, 0, 0)
+#define PIN_PD21__G1_TXCTL		PINMUX_PIN(PIN_PD21, 1, 2)
+#define PIN_PD21__FLEXCOM6_IO2		PINMUX_PIN(PIN_PD21, 2, 3)
+#define PIN_PD21__TK1			PINMUX_PIN(PIN_PD21, 3, 1)
+
+#define PIN_PD22			118
+#define PIN_PD22__GPIO			PINMUX_PIN(PIN_PD22, 0, 0)
+#define PIN_PD22__G1_TX0		PINMUX_PIN(PIN_PD22, 1, 1)
+#define PIN_PD22__FLEXCOM6_IO3		PINMUX_PIN(PIN_PD22, 2, 3)
+#define PIN_PD22__TF1			PINMUX_PIN(PIN_PD22, 3, 1)
+
+#define PIN_PD23			119
+#define PIN_PD23__GPIO			PINMUX_PIN(PIN_PD23, 0, 0)
+#define PIN_PD23__G1_TX1		PINMUX_PIN(PIN_PD23, 1, 1)
+#define PIN_PD23__FLEXCOM6_IO4		PINMUX_PIN(PIN_PD23, 2, 3)
+#define PIN_PD23__TD1			PINMUX_PIN(PIN_PD23, 3, 1)
+
+#define PIN_PD24			120
+#define PIN_PD24__GPIO			PINMUX_PIN(PIN_PD24, 0, 0)
+#define PIN_PD24__G1_RXCTL		PINMUX_PIN(PIN_PD24, 1, 1)
+#define PIN_PD24__FLEXCOM6_IO0		PINMUX_PIN(PIN_PD24, 2, 3)
+#define PIN_PD24__RD1			PINMUX_PIN(PIN_PD24, 3, 1)
+#define PIN_PD24__PDMC0_DS1		PINMUX_PIN(PIN_PD24, 5, 3)
+
+#define PIN_PD25			121
+#define PIN_PD25__GPIO			PINMUX_PIN(PIN_PD25, 0, 0)
+#define PIN_PD25__G1_MDC		PINMUX_PIN(PIN_PD25, 1, 1)
+#define PIN_PD25__FLEXCOM6_IO1		PINMUX_PIN(PIN_PD25, 2, 3)
+#define PIN_PD25__RK1			PINMUX_PIN(PIN_PD25, 3, 1)
+#define PIN_PD25__PDMC0_CLK		PINMUX_PIN(PIN_PD25, 5, 3)
+
+#define PIN_PD26			122
+#define PIN_PD26__GPIO			PINMUX_PIN(PIN_PD26, 0, 0)
+#define PIN_PD26__G1_MDIO		PINMUX_PIN(PIN_PD26, 1, 1)
+#define PIN_PD26__FLEXCOM7_IO4		PINMUX_PIN(PIN_PD26, 2, 2)
+#define PIN_PD26__RF1			PINMUX_PIN(PIN_PD26, 3, 1)
+#define PIN_PD26__I2SMCC1_DIN2		PINMUX_PIN(PIN_PD26, 4, 2)
+#define PIN_PD26__PDMC0_DS0		PINMUX_PIN(PIN_PD26, 5, 3)
+
+#define PIN_PD27			123
+#define PIN_PD27__GPIO			PINMUX_PIN(PIN_PD27, 0, 0)
+#define PIN_PD27__G1_RX0		PINMUX_PIN(PIN_PD27, 1, 1)
+#define PIN_PD27__FLEXCOM7_IO0		PINMUX_PIN(PIN_PD27, 2, 2)
+#define PIN_PD27__SPDIF_RX		PINMUX_PIN(PIN_PD27, 3, 1)
+#define PIN_PD27__I2SMCC1_DIN3		PINMUX_PIN(PIN_PD27, 4, 2)
+
+#define PIN_PD28			124
+#define PIN_PD28__GPIO			PINMUX_PIN(PIN_PD28, 0, 0)
+#define PIN_PD28__G1_RX1		PINMUX_PIN(PIN_PD28, 1, 1)
+#define PIN_PD28__FLEXCOM7_IO1		PINMUX_PIN(PIN_PD28, 2, 2)
+#define PIN_PD28__SPDIF_TX		PINMUX_PIN(PIN_PD28, 3, 1)
+#define PIN_PD28__I2SMCC1_DIN1		PINMUX_PIN(PIN_PD28, 4, 2)
+
+#define PIN_PD29			125
+#define PIN_PD29__GPIO			PINMUX_PIN(PIN_PD29, 0, 0)
+#define PIN_PD29__G1_REFCK		PINMUX_PIN(PIN_PD29, 1, 2)
+#define PIN_PD29__FLEXCOM7_IO2		PINMUX_PIN(PIN_PD29, 2, 2)
+#define PIN_PD29__I2SMCC1_DOUT3		PINMUX_PIN(PIN_PD29, 3, 2)
+
+#define PIN_PD30			126
+#define PIN_PD30__GPIO			PINMUX_PIN(PIN_PD30, 0, 0)
+#define PIN_PD30__G1_RX2		PINMUX_PIN(PIN_PD30, 1, 1)
+#define PIN_PD30__FLEXCOM7_IO3		PINMUX_PIN(PIN_PD30, 2, 2)
+#define PIN_PD30__I2SMCC1_DOUT1		PINMUX_PIN(PIN_PD30, 3, 2)
+#define PIN_PD30__PDMC1_DS1		PINMUX_PIN(PIN_PD30, 4, 3)
+#define PIN_PD30__G1_RXER		PINMUX_PIN(PIN_PD30, 5, 2)
+
+#define PIN_PD31			127
+#define PIN_PD31__GPIO			PINMUX_PIN(PIN_PD31, 0, 0)
+#define PIN_PD31__G1_RX3		PINMUX_PIN(PIN_PD31, 1, 1)
+#define PIN_PD31__FLEXCOM5_IO4		PINMUX_PIN(PIN_PD31, 2, 2)
+#define PIN_PD31__I2SMCC1_DOUT2		PINMUX_PIN(PIN_PD31, 3, 3)
+#define PIN_PD31__PDMC1_DS0		PINMUX_PIN(PIN_PD31, 4, 3)
+
+#define PIN_PE0				128
+#define PIN_PE0__GPIO			PINMUX_PIN(PIN_PE0, 0, 0)
+#define PIN_PE0__G1_TX2			PINMUX_PIN(PIN_PE0, 1, 1)
+#define PIN_PE0__FLEXCOM5_IO2		PINMUX_PIN(PIN_PE0, 2, 2)
+#define PIN_PE0__I2SMCC1_DIN0		PINMUX_PIN(PIN_PE0, 3, 2)
+#define PIN_PE0__PDMC1_CLK		PINMUX_PIN(PIN_PE0, 4, 3)
+
+#define PIN_PE1				129
+#define PIN_PE1__GPIO			PINMUX_PIN(PIN_PE1, 0, 0)
+#define PIN_PE1__G1_TX3			PINMUX_PIN(PIN_PE1, 1, 1)
+#define PIN_PE1__FLEXCOM5_IO3		PINMUX_PIN(PIN_PE1, 2, 2)
+#define PIN_PE1__I2SMCC1_WS		PINMUX_PIN(PIN_PE1, 3, 2)
+#define PIN_PE1__PDMC0_DS1		PINMUX_PIN(PIN_PE1, 4, 4)
+
+#define PIN_PE2				130
+#define PIN_PE2__GPIO			PINMUX_PIN(PIN_PE2, 0, 0)
+#define PIN_PE2__G1_RXCK		PINMUX_PIN(PIN_PE2, 1, 1)
+#define PIN_PE2__FLEXCOM5_IO1		PINMUX_PIN(PIN_PE2, 2, 2)
+#define PIN_PE2__I2SMCC1_CK		PINMUX_PIN(PIN_PE2, 3, 2)
+#define PIN_PE2__PDMC0_CLK		PINMUX_PIN(PIN_PE2, 4, 4)
+
+#define PIN_PE3				131
+#define PIN_PE3__GPIO			PINMUX_PIN(PIN_PE3, 0, 0)
+#define PIN_PE3__G1_TSUCOMP		PINMUX_PIN(PIN_PE3, 1, 1)
+#define PIN_PE3__FLEXCOM5_IO0		PINMUX_PIN(PIN_PE3, 2, 2)
+#define PIN_PE3__I2SMCC1_DOUT0		PINMUX_PIN(PIN_PE3, 3, 2)
+#define PIN_PE3__PDMC0_DS0		PINMUX_PIN(PIN_PE3, 4, 4)
+
+#define PIN_PE4				132
+#define PIN_PE4__GPIO			PINMUX_PIN(PIN_PE4, 0, 0)
+#define PIN_PE4__LCDC_DAT0		PINMUX_PIN(PIN_PE4, 1, 1)
+#define PIN_PE4__FLEXCOM2_IO2		PINMUX_PIN(PIN_PE4, 2, 1)
+#define PIN_PE4__PWML0			PINMUX_PIN(PIN_PE4, 3, 2)
+#define PIN_PE4__TIOA3			PINMUX_PIN(PIN_PE4, 4, 1)
+#define PIN_PE4__I2SMCC0_DIN1		PINMUX_PIN(PIN_PE4, 5, 2)
+
+#define PIN_PE5				133
+#define PIN_PE5__GPIO			PINMUX_PIN(PIN_PE5, 0, 0)
+#define PIN_PE5__LCDC_DAT1		PINMUX_PIN(PIN_PE5, 1, 1)
+#define PIN_PE5__FLEXCOM2_IO3		PINMUX_PIN(PIN_PE5, 2, 1)
+#define PIN_PE5__PWMH0			PINMUX_PIN(PIN_PE5, 3, 2)
+#define PIN_PE5__TIOB3			PINMUX_PIN(PIN_PE5, 4, 1)
+#define PIN_PE5__I2SMCC0_DIN2		PINMUX_PIN(PIN_PE5, 5, 2)
+
+#define PIN_PE6				134
+#define PIN_PE6__GPIO			PINMUX_PIN(PIN_PE6, 0, 0)
+#define PIN_PE6__LCDC_DAT2		PINMUX_PIN(PIN_PE6, 1, 1)
+#define PIN_PE6__FLEXCOM2_IO4		PINMUX_PIN(PIN_PE6, 2, 1)
+#define PIN_PE6__PWML1			PINMUX_PIN(PIN_PE6, 3, 2)
+#define PIN_PE6__TCLK3			PINMUX_PIN(PIN_PE6, 4, 1)
+#define PIN_PE6__I2SMCC0_DIN3		PINMUX_PIN(PIN_PE6, 5, 2)
+
+#define PIN_PE7				135
+#define PIN_PE7__GPIO			PINMUX_PIN(PIN_PE7, 0, 0)
+#define PIN_PE7__LCDC_DAT3		PINMUX_PIN(PIN_PE7, 1, 1)
+#define PIN_PE7__FLEXCOM2_IO5		PINMUX_PIN(PIN_PE7, 2, 1)
+#define PIN_PE7__PWMH1			PINMUX_PIN(PIN_PE7, 3, 2)
+#define PIN_PE7__TIOA4			PINMUX_PIN(PIN_PE7, 4, 1)
+#define PIN_PE7__I2SMCC0_DOUT1		PINMUX_PIN(PIN_PE7, 5, 2)
+
+#define PIN_PE8				136
+#define PIN_PE8__GPIO			PINMUX_PIN(PIN_PE8, 0, 0)
+#define PIN_PE8__LCDC_DAT4		PINMUX_PIN(PIN_PE8, 1, 1)
+#define PIN_PE8__FLEXCOM2_IO0		PINMUX_PIN(PIN_PE8, 2, 1)
+#define PIN_PE8__PWML2			PINMUX_PIN(PIN_PE8, 3, 2)
+#define PIN_PE8__TIOB4			PINMUX_PIN(PIN_PE8, 4, 1)
+#define PIN_PE8__I2SMCC0_CK		PINMUX_PIN(PIN_PE8, 5, 2)
+
+#define PIN_PE9				137
+#define PIN_PE9__GPIO			PINMUX_PIN(PIN_PE9, 0, 0)
+#define PIN_PE9__LCDC_DAT5		PINMUX_PIN(PIN_PE9, 1, 1)
+#define PIN_PE9__FLEXCOM2_IO1		PINMUX_PIN(PIN_PE9, 2, 1)
+#define PIN_PE9__PWMH2			PINMUX_PIN(PIN_PE9, 3, 2)
+#define PIN_PE9__TCLK4			PINMUX_PIN(PIN_PE9, 4, 1)
+#define PIN_PE9__I2SMCC0_WS		PINMUX_PIN(PIN_PE9, 5, 2)
+
+#define PIN_PE10			138
+#define PIN_PE10__GPIO			PINMUX_PIN(PIN_PE10, 0, 0)
+#define PIN_PE10__LCDC_DAT6		PINMUX_PIN(PIN_PE10, 1, 1)
+#define PIN_PE10__FLEXCOM2_IO6		PINMUX_PIN(PIN_PE10, 2, 1)
+#define PIN_PE10__PWML3			PINMUX_PIN(PIN_PE10, 3, 2)
+#define PIN_PE10__TIOA5			PINMUX_PIN(PIN_PE10, 4, 1)
+#define PIN_PE10__I2SMCC0_DOUT2		PINMUX_PIN(PIN_PE10, 5, 2)
+
+#define PIN_PE11			139
+#define PIN_PE11__GPIO			PINMUX_PIN(PIN_PE11, 0, 0)
+#define PIN_PE11__LCDC_DAT7		PINMUX_PIN(PIN_PE11, 1, 1)
+#define PIN_PE11__PWMH3			PINMUX_PIN(PIN_PE11, 3, 2)
+#define PIN_PE11__TIOB5			PINMUX_PIN(PIN_PE11, 4, 1)
+#define PIN_PE11__I2SMCC0_DOUT3		PINMUX_PIN(PIN_PE11, 5, 2)
+
+#define PIN_PE12			140
+#define PIN_PE12__GPIO			PINMUX_PIN(PIN_PE12, 0, 0)
+#define PIN_PE12__LCDC_DEN		PINMUX_PIN(PIN_PE12, 1, 1)
+#define PIN_PE12__PCK3			PINMUX_PIN(PIN_PE12, 2, 4)
+#define PIN_PE12__PWMEXTRG0		PINMUX_PIN(PIN_PE12, 3, 2)
+#define PIN_PE12__TCLK5			PINMUX_PIN(PIN_PE12, 4, 1)
+#define PIN_PE12__I2SMCC0_DIN0		PINMUX_PIN(PIN_PE12, 5, 2)
+
+#define PIN_PE13			141
+#define PIN_PE13__GPIO			PINMUX_PIN(PIN_PE13, 0, 0)
+#define PIN_PE13__LCDC_PCK		PINMUX_PIN(PIN_PE13, 1, 1)
+#define PIN_PE13__PCK4			PINMUX_PIN(PIN_PE13, 2, 3)
+#define PIN_PE13__PWMEXTRG1		PINMUX_PIN(PIN_PE13, 3, 2)
+#define PIN_PE13__I2SMCC0DOUT0		PINMUX_PIN(PIN_PE13, 5, 2)
diff --git a/arch/arm/boot/dts/microchip/sama7d65.dtsi b/arch/arm/boot/dts/microchip/sama7d65.dtsi
new file mode 100644
index 000000000000..e53e2dd6d530
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/sama7d65.dtsi
@@ -0,0 +1,740 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ *  sama7d65.dtsi - Device Tree Include file for SAMA7D65 SoC
+ *
+ *  Copyright (C) 2024 Microchip Technology Inc. and its subsidiaries
+ *
+ *  Author: Ryan Wanner <Ryan.Wanner@microchip.com>
+ *
+ */
+
+#include <dt-bindings/clock/at91.h>
+#include <dt-bindings/dma/at91.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/mfd/at91-usart.h>
+
+/ {
+	model = "Microchip SAMA7D65 family SoC";
+	compatible = "microchip,sama7d65";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			device_type = "cpu";
+			clocks = <&pmc PMC_TYPE_CORE PMC_CPUPLL>;
+			clock-names = "cpu";
+			d-cache-size = <0x8000>;	// L1, 32 KB
+			i-cache-size = <0x8000>;	// L1, 32 KB
+			next-level-cache = <&L2>;
+
+			L2: l2-cache {
+				compatible = "cache";
+				cache-level = <2>;
+				cache-size = <0x40000>; // L2, 256 KB
+				cache-unified;
+			};
+		};
+	};
+
+	clocks {
+		main_xtal: clock-mainxtal {
+			compatible = "fixed-clock";
+			clock-output-names = "main_xtal";
+			#clock-cells = <0>;
+		};
+
+		slow_xtal: clock-slowxtal {
+			compatible = "fixed-clock";
+			clock-output-names = "slow_xtal";
+			#clock-cells = <0>;
+		};
+	};
+
+	ns_sram: sram@100000 {
+		compatible = "mmio-sram";
+		reg = <0x100000 0x20000>;
+		ranges;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		ranges;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		securam: sram@e0000800 {
+			compatible = "microchip,sama7d65-securam", "atmel,sama5d2-securam", "mmio-sram";
+			reg = <0xe0000800 0x4000>;
+			ranges = <0 0xe0000800 0x4000>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 17>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			no-memory-wc;
+		};
+
+		secumod: security-module@e0004000 {
+			compatible = "microchip,sama7d65-secumod", "atmel,sama5d2-secumod", "syscon";
+			reg = <0xe0004000 0x4000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		sfrbu: sfr@e0008000 {
+			compatible = "microchip,sama7d65-sfrbu", "atmel,sama5d2-sfrbu", "syscon";
+			reg = <0xe0008000 0x20>;
+		};
+
+		pioa: pinctrl@e0014000 {
+			compatible = "microchip,sama7d65-pinctrl", "microchip,sama7g5-pinctrl";
+			reg = <0xe0014000 0x800>;
+			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		pmc: clock-controller@e0018000 {
+			compatible = "microchip,sama7d65-pmc", "syscon";
+			reg = <0xe0018000 0x200>;
+			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			#clock-cells = <2>;
+			clocks = <&clk32k 1>, <&clk32k 0>, <&main_xtal>;
+			clock-names = "td_slck", "md_slck", "main_xtal";
+		};
+
+		ps_wdt: watchdog@e001d000 {
+			compatible = "microchip,sama7d65-wdt", "microchip,sama7g5-wdt";
+			reg = <0xe001d000 0x30>;
+			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk32k 0>;
+		};
+
+		reset_controller: reset-controller@e001d100 {
+			compatible = "microchip,sama7d65-rstc", "microchip,sama7g5-rstc";
+			reg = <0xe001d100 0xc>, <0xe001d1e4 0x4>;
+			#reset-cells = <1>;
+			clocks = <&clk32k 0>;
+		};
+
+		shdwc: poweroff@e001d200 {
+			compatible = "microchip,sama7d65-shdwc", "microchip,sama7g5-shdwc", "syscon";
+			reg = <0xe001d200 0x20>;
+			clocks = <&clk32k 0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			atmel,wakeup-rtc-timer;
+			atmel,wakeup-rtt-timer;
+			status = "disabled";
+		};
+
+		rtt: rtc@e001d300 {
+			compatible = "microchip,sama7d65-rtt", "atmel,at91sam9260-rtt";
+			reg = <0xe001d300 0x30>;
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk32k 0>;
+		};
+
+		clk32k: clock-controller@e001d500 {
+			compatible = "microchip,sama7d65-sckc", "microchip,sam9x60-sckc";
+			reg = <0xe001d500 0x4>;
+			clocks = <&slow_xtal>;
+			#clock-cells = <1>;
+		};
+
+		gpbr: syscon@e001d700 {
+			compatible = "microchip,sama7d65-gpbr", "syscon";
+			reg = <0xe001d700 0x48>;
+		};
+
+		rtc: rtc@e001d800 {
+			compatible = "microchip,sama7d65-rtc", "microchip,sam9x60-rtc";
+			reg = <0xe001d800 0x30>;
+			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk32k 1>;
+		};
+
+		chipid@e0020000 {
+			compatible = "microchip,sama7d65-chipid";
+			reg = <0xe0020000 0x8>;
+		};
+
+		can0: can@e0828000 {
+			compatible = "bosch,m_can";
+			reg = <0xe0828000 0x200>, <0x100000 0x7800>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 58>, <&pmc PMC_TYPE_GCK 58>;
+			clock-names = "hclk", "cclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 58>;
+			assigned-clock-rates = <40000000>;
+			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_UTMI>;
+			bosch,mram-cfg = <0x3400 0 0 64 0 0 32 32>;
+			status = "disabled";
+		};
+
+		can1: can@e082c000 {
+			compatible = "bosch,m_can";
+			reg = <0xe082c000 0x200>, <0x100000 0xbc00>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 59>, <&pmc PMC_TYPE_GCK 59>;
+			clock-names = "hclk", "cclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 59>;
+			assigned-clock-rates = <40000000>;
+			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_UTMI>;
+			bosch,mram-cfg = <0x7800 0 0 64 0 0 32 32>;
+			status = "disabled";
+		};
+
+		can2: can@e0830000 {
+			compatible = "bosch,m_can";
+			reg = <0xe0830000 0x200>, <0x100000 0x10000>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 60>, <&pmc PMC_TYPE_GCK 60>;
+			clock-names = "hclk", "cclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 60>;
+			assigned-clock-rates = <40000000>;
+			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_UTMI>;
+			bosch,mram-cfg = <0xbc00 0 0 64 0 0 32 32>;
+			status = "disabled";
+		};
+
+		can3: can@e0834000 {
+			compatible = "bosch,m_can";
+			reg = <0xe0834000 0x200>, <0x110000 0x4400>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 61>, <&pmc PMC_TYPE_GCK 61>;
+			clock-names = "hclk", "cclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 61>;
+			assigned-clock-rates = <40000000>;
+			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_UTMI>;
+			bosch,mram-cfg = <0x0 0 0 64 0 0 32 32>;
+			status = "disabled";
+		};
+
+		can4: can@e0838000 {
+			compatible = "bosch,m_can";
+			reg = <0xe0838000 0x200>, <0x110000 0x8800>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 62>, <&pmc PMC_TYPE_GCK 62>;
+			clock-names = "hclk", "cclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 62>;
+			assigned-clock-rates = <40000000>;
+			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_UTMI>;
+			bosch,mram-cfg = <0x4400 0 0 64 0 0 32 32>;
+			status = "disabled";
+		};
+
+		dma2: dma-controller@e1200000 {
+			compatible = "microchip,sama7d65-dma", "microchip,sama7g5-dma";
+			reg = <0xe1200000 0x1000>;
+			interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 23>;
+			clock-names = "dma_clk";
+			dma-requests = <0>;
+			status = "disabled";
+		};
+
+		sdmmc1: mmc@e1208000 {
+			compatible = "microchip,sama7d65-sdhci", "microchip,sam9x60-sdhci";
+			reg = <0xe1208000 0x400>;
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 76>, <&pmc PMC_TYPE_GCK 76>;
+			clock-names = "hclock", "multclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 76>;
+			assigned-clock-rates = <200000000>;
+			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_MCK1>;
+			status = "disabled";
+		};
+
+		aes: crypto@e1600000 {
+			compatible = "microchip,sama7d65-aes", "atmel,at91sam9g46-aes";
+			reg = <0xe1600000 0x100>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 26>;
+			clock-names = "aes_clk";
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(1)>,
+			       <&dma0 AT91_XDMAC_DT_PERID(2)>;
+			dma-names = "tx", "rx";
+		};
+
+		sha: crypto@e1604000 {
+			compatible = "microchip,sama7d65-sha", "atmel,at91sam9g46-sha";
+			reg = <0xe1604000 0x100>;
+			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 78>;
+			clock-names = "sha_clk";
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(48)>;
+			dma-names = "tx";
+		};
+
+		tdes: crypto@e1608000 {
+			compatible = "microchip,sama7d65-tdes", "atmel,at91sam9g46-tdes";
+			reg = <0xe1608000 0x100>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 91>;
+			clock-names = "tdes_clk";
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(54)>,
+			       <&dma0 AT91_XDMAC_DT_PERID(53)>;
+			dma-names = "tx", "rx";
+		};
+
+		trng: rng@e160c000 {
+			compatible = "microchip,sama7d65-trng", "microchip,sam9x60-trng";
+			reg = <0xe160c000 0x100>;
+			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 92>;
+		};
+
+		dma0: dma-controller@e1610000 {
+			compatible = "microchip,sama7d65-dma", "microchip,sama7g5-dma";
+			reg = <0xe1610000 0x1000>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 21>;
+			clock-names = "dma_clk";
+			status = "disabled";
+		};
+
+		dma1: dma-controller@e1614000 {
+			compatible = "microchip,sama7d65-dma", "microchip,sama7g5-dma";
+			reg = <0xe1614000 0x1000>;
+			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 22>;
+			clock-names = "dma_clk";
+			status = "disabled";
+		};
+
+		gmac0: ethernet@e1618000 {
+			compatible = "microchip,sama7d65-gem", "microchip,sama7g5-gem";
+			reg = <0xe1618000 0x2000>;
+			interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 46>, <&pmc PMC_TYPE_PERIPHERAL 46>, <&pmc PMC_TYPE_GCK 46>, <&pmc PMC_TYPE_GCK 49>;
+			clock-names = "pclk", "hclk", "tx_clk", "tsu_clk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 46>, <&pmc PMC_TYPE_GCK 49>;
+			assigned-clock-rates = <125000000>, <200000000>;
+			status = "disabled";
+		};
+
+		gmac1: ethernet@e161c000 {
+			compatible = "microchip,sama7d65-gem", "microchip,sama7g5-gem";
+			reg = <0xe161c000 0x2000>;
+			interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 47>, <&pmc PMC_TYPE_PERIPHERAL 47>,<&pmc PMC_TYPE_GCK 47>, <&pmc PMC_TYPE_GCK 50>;
+			clock-names = "pclk", "hclk", "tx_clk", "tsu_clk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 47>, <&pmc PMC_TYPE_GCK 50>;
+			assigned-clock-rates = <125000000>, <200000000>;
+			status = "disabled";
+		};
+
+		pit64b0: timer@e1800000 {
+			compatible = "microchip,sama7d65-pit64b", "microchip,sam9x60-pit64b";
+			reg = <0xe1800000 0x100>;
+			interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 66>, <&pmc PMC_TYPE_GCK 66>;
+			clock-names = "pclk", "gclk";
+		};
+
+		pit64b1: timer@e1804000 {
+			compatible = "microchip,sama7d65-pit64b", "microchip,sam9x60-pit64b";
+			reg = <0xe1804000 0x100>;
+			interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 67>, <&pmc PMC_TYPE_GCK 67>;
+			clock-names = "pclk", "gclk";
+		};
+
+		pwm: pwm@e1818000 {
+			compatible = "microchip,sama7d65-pwm", "atmel,sama5d2-pwm";
+			reg = <0xe1818000 0x500>;
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 72>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
+		flx0: flexcom@e1820000 {
+			compatible = "microchip,sama7d65-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe1820000 0x200>;
+			ranges = <0x0 0xe1820000 0x800>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 34>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			uart0: serial@200 {
+				compatible = "microchip,sama7d65-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 34>;
+				clock-names = "usart";
+				dmas = <&dma1 AT91_XDMAC_DT_PERID(6)>,
+				       <&dma1 AT91_XDMAC_DT_PERID(5)>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			i2c0: i2c@600 {
+				compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 34>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				atmel,fifo-size = <32>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(6)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(5)>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+		};
+
+		flx1: flexcom@e1824000 {
+			compatible = "microchip,sama7d65-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe1824000 0x200>;
+			ranges = <0x0 0xe1824000 0x800>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 35>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			spi1: spi@400 {
+				compatible = "microchip,sama7d65-spi", "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 35>;
+				clock-names = "spi_clk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(8)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(7)>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@600 {
+				compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 35>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(8)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(7)>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+		};
+
+		flx2: flexcom@e1828000 {
+			compatible = "microchip,sama7d65-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe1828000 0x200>;
+			ranges = <0x0 0xe1828000 0x800>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 36>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			uart2: serial@200 {
+				compatible = "microchip,sama7d65-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 36>;
+				clock-names = "usart";
+				dmas = <&dma1 AT91_XDMAC_DT_PERID(10)>,
+				       <&dma1 AT91_XDMAC_DT_PERID(9)>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+		};
+
+		flx3: flexcom@e182c000 {
+			compatible = "microchip,sama7d65-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe182c000 0x200>;
+			ranges = <0x0 0xe182c000 0x800>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 37>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			uart3: serial@200 {
+				compatible = "microchip,sama7d65-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 37>;
+				clock-names = "usart";
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(12)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(11)>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			i2c3: i2c@600 {
+				compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 37>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(12)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(11)>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+
+		};
+
+		flx4: flexcom@e2018000 {
+			compatible = "microchip,sama7d65-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe2018000 0x200>;
+			ranges = <0x0 0xe2018000 0x800>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 38>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			uart4: serial@200 {
+				compatible = "microchip,sama7d65-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 38>;
+				clock-names = "usart";
+				dmas = <&dma1 AT91_XDMAC_DT_PERID(14)>,
+				       <&dma1 AT91_XDMAC_DT_PERID(13)>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+
+			spi4: spi@400 {
+				compatible = "microchip,sama7d65-spi", "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 38>;
+				clock-names = "spi_clk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(14)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(13)>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+		};
+
+		flx5: flexcom@e201c000 {
+			compatible = "microchip,sama7d65-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe201c000 0x200>;
+			ranges = <0x0 0xe201c000 0x800>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 39>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			i2c5: i2c@600 {
+				compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 39>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(16)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(15)>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+		};
+
+		flx6: flexcom@e2020000 {
+			compatible = "microchip,sama7d65-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe2020000 0x200>;
+			ranges = <0x0 0xe2020000 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 40>;
+			status = "disabled";
+
+			uart6: serial@200 {
+				compatible = "microchip,sama7d65-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 40>;
+				clock-names = "usart";
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				atmel,fifo-size = <16>;
+				status = "disabled";
+			};
+		};
+
+		flx7: flexcom@e2024000 {
+			compatible = "microchip,sama7d65-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe2024000 0x200>;
+			ranges = <0x0 0xe2024000 0x800>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 41>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			uart7: serial@200 {
+				compatible = "microchip,sama7d65-usart", "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 41>;
+				clock-names = "usart";
+				dmas = <&dma1 AT91_XDMAC_DT_PERID(20)>,
+				       <&dma1 AT91_XDMAC_DT_PERID(19)>;
+				dma-names = "tx", "rx";
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				atmel,fifo-size = <16>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
+				status = "disabled";
+			};
+		};
+
+		flx8: flexcom@e281c000 {
+			compatible = "microchip,sama7d65-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe281c000 0x200>;
+			ranges = <0x0 0xe281c000 0x800>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 42>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			i2c8: i2c@600 {
+				compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 42>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(22)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(21)>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+		};
+
+		flx9: flexcom@e2820000 {
+			compatible = "microchip,sama7d65-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe2820000 0x200>;
+			ranges = <0x0 0xe281c000 0x800>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 43>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			i2c9: i2c@600 {
+				compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 43>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(24)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(23)>;
+				dma-names = "tx", "rx";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+		};
+
+		flx10: flexcom@e2824000 {
+			compatible = "microchip,sama7d65-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe2824000 0x200>;
+			ranges = <0x0 0xe2824000 0x800>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 44>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			i2c10: i2c@600 {
+				compatible = "microchip,sama7d65-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 44>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+		};
+
+		uddrc: uddrc@e3800000 {
+			compatible = "microchip,sama7d65-uddrc", "microchip,sama7g5-uddrc";
+			reg = <0xe3800000 0x4000>;
+		};
+
+		ddr3phy: ddr3phy@e3804000 {
+			compatible = "microchip,sama7d65-ddr3phy", "microchip,sama7g5-ddr3phy";
+			reg = <0xe3804000 0x1000>;
+		};
+
+		gic: interrupt-controller@e8c11000 {
+			compatible = "arm,cortex-a7-gic";
+			reg = <0xe8c11000 0x1000>,
+			      <0xe8c12000 0x2000>;
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/sama7g5-pinfunc.h b/arch/arm/boot/dts/microchip/sama7g5-pinfunc.h
index 4eb30445d205..a67a156e26ab 100644
--- a/arch/arm/boot/dts/sama7g5-pinfunc.h
+++ b/arch/arm/boot/dts/microchip/sama7g5-pinfunc.h
@@ -261,7 +261,7 @@
 #define PIN_PB2__FLEXCOM6_IO0		PINMUX_PIN(PIN_PB2, 2, 1)
 #define PIN_PB2__ADTRG			PINMUX_PIN(PIN_PB2, 3, 1)
 #define PIN_PB2__A20			PINMUX_PIN(PIN_PB2, 4, 1)
-#define PIN_PB2__FLEXCOM11_IO0		PINMUX_PIN(PIN_PB2, 6, 3)
+#define PIN_PB2__FLEXCOM11_IO1		PINMUX_PIN(PIN_PB2, 6, 3)
 #define PIN_PB3				35
 #define PIN_PB3__GPIO			PINMUX_PIN(PIN_PB3, 0, 0)
 #define PIN_PB3__RF1			PINMUX_PIN(PIN_PB3, 1, 1)
@@ -673,7 +673,7 @@
 #define PIN_PD8__GPIO			PINMUX_PIN(PIN_PD8, 0, 0)
 #define PIN_PD8__SDMMC2_DAT3		PINMUX_PIN(PIN_PD8, 1, 1)
 #define PIN_PD8__I2SMCC0_DIN0		PINMUX_PIN(PIN_PD8, 3, 1)
-#define PIN_PD8__A11_NANDCLE		PINMUX_PIN(PIN_PD8, 4, 2)
+#define PIN_PD8__A22_NANDCLE		PINMUX_PIN(PIN_PD8, 4, 2)
 #define PIN_PD8__TIOA2			PINMUX_PIN(PIN_PD8, 5, 2)
 #define PIN_PD8__FLEXCOM11_IO0		PINMUX_PIN(PIN_PD8, 6, 5)
 #define PIN_PD9				105
diff --git a/arch/arm/boot/dts/sama7g5.dtsi b/arch/arm/boot/dts/microchip/sama7g5.dtsi
index 4decd3a91a76..381cbcfcb34a 100644
--- a/arch/arm/boot/dts/sama7g5.dtsi
+++ b/arch/arm/boot/dts/microchip/sama7g5.dtsi
@@ -9,11 +9,15 @@
  *
  */
 
+#include <dt-bindings/iio/adc/at91-sama5d2_adc.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/at91.h>
 #include <dt-bindings/dma/at91.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/at91-usart.h>
+#include <dt-bindings/nvmem/microchip,sama7g5-otpc.h>
+#include <dt-bindings/thermal/thermal.h>
 
 / {
 	model = "Microchip SAMA7G5 family SoC";
@@ -33,6 +37,17 @@
 			clocks = <&pmc PMC_TYPE_CORE PMC_CPUPLL>;
 			clock-names = "cpu";
 			operating-points-v2 = <&cpu_opp_table>;
+			#cooling-cells = <2>; /* min followed by max */
+			d-cache-size = <0x8000>;	// L1, 32 KB
+			i-cache-size = <0x8000>;	// L1, 32 KB
+			next-level-cache = <&L2>;
+
+			L2: l2-cache {
+				compatible = "cache";
+				cache-level = <2>;
+				cache-size = <0x40000>; // L2, 256 KB
+				cache-unified;
+			};
 		};
 	};
 
@@ -71,20 +86,63 @@
 		};
 	};
 
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <1000>;
+			polling-delay = <5000>;
+			thermal-sensors = <&thermal_sensor>;
+
+			trips {
+				cpu_normal: cpu-alert0 {
+					temperature = <90000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				cpu_hot: cpu-alert1 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				cpu_critical: cpu-critical {
+					temperature = <100000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_normal>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+
+				map1 {
+					trip = <&cpu_hot>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
 	clocks {
-		slow_xtal: slow_xtal {
+		slow_xtal: clock-slowxtal {
 			compatible = "fixed-clock";
+			clock-output-names = "slow_xtal";
 			#clock-cells = <0>;
 		};
 
-		main_xtal: main_xtal {
+		main_xtal: clock-mainxtal {
 			compatible = "fixed-clock";
+			clock-output-names = "main_xtal";
 			#clock-cells = <0>;
 		};
 
-		usb_clk: usb_clk {
+		usb_clk: clock-usbclk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
+			clock-output-names = "usb_clk";
 			clock-frequency = <48000000>;
 		};
 	};
@@ -107,6 +165,13 @@
 		ranges;
 	};
 
+	thermal_sensor: thermal-sensor {
+		compatible = "generic-adc-thermal";
+		#thermal-sensor-cells = <0>;
+		io-channels = <&adc AT91_SAMA7G5_ADC_TEMP_CHANNEL>;
+		io-channel-names = "sensor-channel";
+	};
+
 	soc {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -152,7 +217,7 @@
 			};
 		};
 
-		securam: securam@e0000000 {
+		securam: sram@e0000000 {
 			compatible = "microchip,sama7g5-securam", "atmel,sama5d2-securam", "mmio-sram";
 			reg = <0xe0000000 0x4000>;
 			clocks = <&pmc PMC_TYPE_PERIPHERAL 18>;
@@ -189,7 +254,7 @@
 			clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
 		};
 
-		pmc: pmc@e0018000 {
+		pmc: clock-controller@e0018000 {
 			compatible = "microchip,sama7g5-pmc", "syscon";
 			reg = <0xe0018000 0x200>;
 			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
@@ -198,7 +263,14 @@
 			clock-names = "td_slck", "md_slck", "main_xtal";
 		};
 
-		shdwc: shdwc@e001d010 {
+		reset_controller: reset-controller@e001d000 {
+			compatible = "microchip,sama7g5-rstc";
+			reg = <0xe001d000 0xc>, <0xe001d0e4 0x4>;
+			#reset-cells = <1>;
+			clocks = <&clk32k 0>;
+		};
+
+		shdwc: poweroff@e001d010 {
 			compatible = "microchip,sama7g5-shdwc", "syscon";
 			reg = <0xe001d010 0x10>;
 			clocks = <&clk32k 0>;
@@ -209,11 +281,11 @@
 			status = "disabled";
 		};
 
-		rtt: rtt@e001d020 {
+		rtt: rtc@e001d020 {
 			compatible = "microchip,sama7g5-rtt", "microchip,sam9x60-rtt", "atmel,at91sam9260-rtt";
 			reg = <0xe001d020 0x30>;
 			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&clk32k 0>;
+			clocks = <&clk32k 1>;
 		};
 
 		clk32k: clock-controller@e001d050 {
@@ -307,8 +379,8 @@
 			compatible = "bosch,m_can";
 			reg = <0xe0828000 0x100>, <0x100000 0x7800>;
 			reg-names = "m_can", "message_ram";
-			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "int0", "int1";
 			clocks = <&pmc PMC_TYPE_PERIPHERAL 61>, <&pmc PMC_TYPE_GCK 61>;
 			clock-names = "hclk", "cclk";
@@ -323,8 +395,8 @@
 			compatible = "bosch,m_can";
 			reg = <0xe082c000 0x100>, <0x100000 0xbc00>;
 			reg-names = "m_can", "message_ram";
-			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "int0", "int1";
 			clocks = <&pmc PMC_TYPE_PERIPHERAL 62>, <&pmc PMC_TYPE_GCK 62>;
 			clock-names = "hclk", "cclk";
@@ -339,8 +411,8 @@
 			compatible = "bosch,m_can";
 			reg = <0xe0830000 0x100>, <0x100000 0x10000>;
 			reg-names = "m_can", "message_ram";
-			interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "int0", "int1";
 			clocks = <&pmc PMC_TYPE_PERIPHERAL 63>, <&pmc PMC_TYPE_GCK 63>;
 			clock-names = "hclk", "cclk";
@@ -355,8 +427,8 @@
 			compatible = "bosch,m_can";
 			reg = <0xe0834000 0x100>, <0x110000 0x4400>;
 			reg-names = "m_can", "message_ram";
-			interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "int0", "int1";
 			clocks = <&pmc PMC_TYPE_PERIPHERAL 64>, <&pmc PMC_TYPE_GCK 64>;
 			clock-names = "hclk", "cclk";
@@ -371,8 +443,8 @@
 			compatible = "bosch,m_can";
 			reg = <0xe0838000 0x100>, <0x110000 0x8800>;
 			reg-names = "m_can", "message_ram";
-			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "int0", "int1";
 			clocks = <&pmc PMC_TYPE_PERIPHERAL 65>, <&pmc PMC_TYPE_GCK 65>;
 			clock-names = "hclk", "cclk";
@@ -387,8 +459,8 @@
 			compatible = "bosch,m_can";
 			reg = <0xe083c000 0x100>, <0x110000 0xcc00>;
 			reg-names = "m_can", "message_ram";
-			interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "int0", "int1";
 			clocks = <&pmc PMC_TYPE_PERIPHERAL 66>, <&pmc PMC_TYPE_GCK 66>;
 			clock-names = "hclk", "cclk";
@@ -412,6 +484,9 @@
 			atmel,min-sample-rate-hz = <200000>;
 			atmel,max-sample-rate-hz = <20000000>;
 			atmel,startup-time-ms = <4>;
+			#io-channel-cells = <1>;
+			nvmem-cells = <&temperature_calib>;
+			nvmem-cell-names = "temperature_calib";
 			status = "disabled";
 		};
 
@@ -454,6 +529,57 @@
 			status = "disabled";
 		};
 
+		csi2dc: csi2dc@e1404000 {
+			compatible = "microchip,sama7g5-csi2dc";
+			reg = <0xe1404000 0x500>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 34>, <&xisc>;
+			clock-names = "pclk", "scck";
+			assigned-clocks = <&xisc>;
+			assigned-clock-rates = <266000000>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				port@0 {
+					reg = <0>;
+					csi2dc_in: endpoint {
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					csi2dc_out: endpoint {
+						bus-width = <14>;
+						hsync-active = <1>;
+						vsync-active = <1>;
+						remote-endpoint = <&xisc_in>;
+					};
+				};
+			};
+		};
+
+		xisc: xisc@e1408000 {
+			compatible = "microchip,sama7g5-isc";
+			reg = <0xe1408000 0x2000>;
+			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 56>;
+			clock-names = "hclock";
+			#clock-cells = <0>;
+			clock-output-names = "isc-mck";
+			status = "disabled";
+
+			port {
+				xisc_in: endpoint {
+					bus-type = <5>; /* Parallel */
+					bus-width = <14>;
+					hsync-active = <1>;
+					vsync-active = <1>;
+					remote-endpoint = <&csi2dc_out>;
+				};
+			};
+		};
+
 		pwm: pwm@e1604000 {
 			compatible = "microchip,sama7g5-pwm", "atmel,sama5d2-pwm";
 			reg = <0xe1604000 0x4000>;
@@ -463,6 +589,30 @@
 			status = "disabled";
 		};
 
+		pdmc0: sound@e1608000 {
+			compatible = "microchip,sama7g5-pdmc";
+			reg = <0xe1608000 0x1000>;
+			interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
+			#sound-dai-cells = <0>;
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(37)>;
+			dma-names = "rx";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 68>, <&pmc PMC_TYPE_GCK 68>;
+			clock-names = "pclk", "gclk";
+			status = "disabled";
+		};
+
+		pdmc1: sound@e160c000 {
+			compatible = "microchip,sama7g5-pdmc";
+			reg = <0xe160c000 0x1000>;
+			interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+			#sound-dai-cells = <0>;
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(38)>;
+			dma-names = "rx";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 69>, <&pmc PMC_TYPE_GCK 69>;
+			clock-names = "pclk", "gclk";
+			status = "disabled";
+		};
+
 		spdifrx: spdifrx@e1614000 {
 			#sound-dai-cells = <0>;
 			compatible = "microchip,sama7g5-spdifrx";
@@ -561,7 +711,7 @@
 		};
 
 		flx0: flexcom@e1818000 {
-			compatible = "atmel,sama5d2-flexcom";
+			compatible = "microchip,sama7g5-flexcom", "atmel,sama5d2-flexcom";
 			reg = <0xe1818000 0x200>;
 			clocks = <&pmc PMC_TYPE_PERIPHERAL 38>;
 			#address-cells = <1>;
@@ -572,11 +722,12 @@
 			uart0: serial@200 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0x200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 38>;
 				clock-names = "usart";
 				dmas = <&dma1 AT91_XDMAC_DT_PERID(6)>,
-					<&dma1 AT91_XDMAC_DT_PERID(5)>;
+				       <&dma1 AT91_XDMAC_DT_PERID(5)>;
 				dma-names = "tx", "rx";
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -585,7 +736,7 @@
 		};
 
 		flx1: flexcom@e181c000 {
-			compatible = "atmel,sama5d2-flexcom";
+			compatible = "microchip,sama7g5-flexcom", "atmel,sama5d2-flexcom";
 			reg = <0xe181c000 0x200>;
 			clocks = <&pmc PMC_TYPE_PERIPHERAL 39>;
 			#address-cells = <1>;
@@ -601,15 +752,15 @@
 				#size-cells = <0>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 39>;
 				atmel,fifo-size = <32>;
-				dmas = <&dma0 AT91_XDMAC_DT_PERID(7)>,
-					<&dma0 AT91_XDMAC_DT_PERID(8)>;
-				dma-names = "rx", "tx";
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(8)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(7)>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 		};
 
 		flx3: flexcom@e1824000 {
-			compatible = "atmel,sama5d2-flexcom";
+			compatible = "microchip,sama7g5-flexcom", "atmel,sama5d2-flexcom";
 			reg = <0xe1824000 0x200>;
 			clocks = <&pmc PMC_TYPE_PERIPHERAL 41>;
 			#address-cells = <1>;
@@ -620,11 +771,12 @@
 			uart3: serial@200 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0x200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 41>;
 				clock-names = "usart";
 				dmas = <&dma1 AT91_XDMAC_DT_PERID(12)>,
-					<&dma1 AT91_XDMAC_DT_PERID(11)>;
+				       <&dma1 AT91_XDMAC_DT_PERID(11)>;
 				dma-names = "tx", "rx";
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -652,7 +804,7 @@
 		};
 
 		flx4: flexcom@e2018000 {
-			compatible = "atmel,sama5d2-flexcom";
+			compatible = "microchip,sama7g5-flexcom", "atmel,sama5d2-flexcom";
 			reg = <0xe2018000 0x200>;
 			clocks = <&pmc PMC_TYPE_PERIPHERAL 42>;
 			#address-cells = <1>;
@@ -663,11 +815,12 @@
 			uart4: serial@200 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0x200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 42>;
 				clock-names = "usart";
 				dmas = <&dma1 AT91_XDMAC_DT_PERID(14)>,
-					<&dma1 AT91_XDMAC_DT_PERID(13)>;
+				       <&dma1 AT91_XDMAC_DT_PERID(13)>;
 				dma-names = "tx", "rx";
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -677,7 +830,7 @@
 		};
 
 		flx7: flexcom@e2024000 {
-			compatible = "atmel,sama5d2-flexcom";
+			compatible = "microchip,sama7g5-flexcom", "atmel,sama5d2-flexcom";
 			reg = <0xe2024000 0x200>;
 			clocks = <&pmc PMC_TYPE_PERIPHERAL 45>;
 			#address-cells = <1>;
@@ -688,11 +841,12 @@
 			uart7: serial@200 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0x200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 45>;
 				clock-names = "usart";
 				dmas = <&dma1 AT91_XDMAC_DT_PERID(20)>,
-					<&dma1 AT91_XDMAC_DT_PERID(19)>;
+				       <&dma1 AT91_XDMAC_DT_PERID(19)>;
 				dma-names = "tx", "rx";
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -704,12 +858,12 @@
 		gmac0: ethernet@e2800000 {
 			compatible = "microchip,sama7g5-gem";
 			reg = <0xe2800000 0x1000>;
-			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&pmc PMC_TYPE_PERIPHERAL 51>, <&pmc PMC_TYPE_PERIPHERAL 51>, <&pmc PMC_TYPE_GCK 51>, <&pmc PMC_TYPE_GCK 53>;
 			clock-names = "pclk", "hclk", "tx_clk", "tsu_clk";
 			assigned-clocks = <&pmc PMC_TYPE_GCK 51>;
@@ -720,8 +874,8 @@
 		gmac1: ethernet@e2804000 {
 			compatible = "microchip,sama7g5-emac";
 			reg = <0xe2804000 0x1000>;
-			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH
-				      GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&pmc PMC_TYPE_PERIPHERAL 52>, <&pmc PMC_TYPE_PERIPHERAL 52>;
 			clock-names = "pclk", "hclk";
 			status = "disabled";
@@ -770,7 +924,7 @@
 		};
 
 		flx8: flexcom@e2818000 {
-			compatible = "atmel,sama5d2-flexcom";
+			compatible = "microchip,sama7g5-flexcom", "atmel,sama5d2-flexcom";
 			reg = <0xe2818000 0x200>;
 			clocks = <&pmc PMC_TYPE_PERIPHERAL 46>;
 			#address-cells = <1>;
@@ -786,15 +940,15 @@
 				#size-cells = <0>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 46>;
 				atmel,fifo-size = <32>;
-				dmas = <&dma0 AT91_XDMAC_DT_PERID(21)>,
-					<&dma0 AT91_XDMAC_DT_PERID(22)>;
-				dma-names = "rx", "tx";
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(22)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(21)>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 		};
 
 		flx9: flexcom@e281c000 {
-			compatible = "atmel,sama5d2-flexcom";
+			compatible = "microchip,sama7g5-flexcom", "atmel,sama5d2-flexcom";
 			reg = <0xe281c000 0x200>;
 			clocks = <&pmc PMC_TYPE_PERIPHERAL 47>;
 			#address-cells = <1>;
@@ -810,15 +964,39 @@
 				#size-cells = <0>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 47>;
 				atmel,fifo-size = <32>;
-				dmas = <&dma0 AT91_XDMAC_DT_PERID(23)>,
-					<&dma0 AT91_XDMAC_DT_PERID(24)>;
-				dma-names = "rx", "tx";
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(24)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(23)>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+		};
+
+		flx10: flexcom@e2820000 {
+			compatible = "microchip,sama7g5-flexcom", "atmel,sama5d2-flexcom";
+			reg = <0xe2820000 0x200>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 48>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xe2820000 0x800>;
+			status = "disabled";
+
+			i2c10: i2c@600 {
+				compatible = "microchip,sama7g5-i2c", "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 48>;
+				atmel,fifo-size = <32>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(26)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(25)>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 		};
 
 		flx11: flexcom@e2824000 {
-			compatible = "atmel,sama5d2-flexcom";
+			compatible = "microchip,sama7g5-flexcom", "atmel,sama5d2-flexcom";
 			reg = <0xe2824000 0x200>;
 			clocks = <&pmc PMC_TYPE_PERIPHERAL 49>;
 			#address-cells = <1>;
@@ -835,9 +1013,9 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				atmel,fifo-size = <32>;
-				dmas = <&dma0 AT91_XDMAC_DT_PERID(27)>,
-					    <&dma0 AT91_XDMAC_DT_PERID(28)>;
-				dma-names = "rx", "tx";
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(28)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(27)>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 		};
@@ -852,12 +1030,22 @@
 			reg = <0xe3804000 0x1000>;
 		};
 
+		otpc: efuse@e8c00000 {
+			compatible = "microchip,sama7g5-otpc", "syscon";
+			reg = <0xe8c00000 0x100>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			temperature_calib: calib@1 {
+				reg = <OTP_PKT(1) 76>;
+			};
+		};
+
 		gic: interrupt-controller@e8c11000 {
 			compatible = "arm,cortex-a7-gic";
 			#interrupt-cells = <3>;
 			#address-cells = <0>;
 			interrupt-controller;
-			interrupt-parent;
 			reg = <0xe8c11000 0x1000>,
 				<0xe8c12000 0x2000>;
 		};
diff --git a/arch/arm/boot/dts/tny_a9260.dts b/arch/arm/boot/dts/microchip/tny_a9260.dts
index ef6d586ce887..f0f2a787d669 100644
--- a/arch/arm/boot/dts/tny_a9260.dts
+++ b/arch/arm/boot/dts/microchip/tny_a9260.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * tny_a9260.dts - Device Tree file for Caloa TNY A9260 board
+ * tny_a9260.dts - Device Tree file for Calao TNY A9260 board
  *
  * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
  */
diff --git a/arch/arm/boot/dts/tny_a9260_common.dtsi b/arch/arm/boot/dts/microchip/tny_a9260_common.dtsi
index 70e5635c78ed..4d4377f51bec 100644
--- a/arch/arm/boot/dts/tny_a9260_common.dtsi
+++ b/arch/arm/boot/dts/microchip/tny_a9260_common.dtsi
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * tny_a9260_common.dtsi - Device Tree file for Caloa TNY A926x board
+ * tny_a9260_common.dtsi - Device Tree file for Calao TNY A926x board
  *
  * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
  */
diff --git a/arch/arm/boot/dts/tny_a9263.dts b/arch/arm/boot/dts/microchip/tny_a9263.dts
index 62b7d9f9a926..fd8244b56e05 100644
--- a/arch/arm/boot/dts/tny_a9263.dts
+++ b/arch/arm/boot/dts/microchip/tny_a9263.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * usb_a9263.dts - Device Tree file for Caloa USB A9293 board
+ * usb_a9263.dts - Device Tree file for Calao USB A9293 board
  *
  *  Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
  */
@@ -64,7 +64,7 @@
 				nand@3 {
 					reg = <0x3 0x0 0x800000>;
 					rb-gpios = <&pioA 22 GPIO_ACTIVE_HIGH>;
-					cs-gpios = <&pioA 15 GPIO_ACTIVE_HIGH>;
+					cs-gpios = <&pioD 15 GPIO_ACTIVE_HIGH>;
 					nand-bus-width = <8>;
 					nand-ecc-mode = "soft";
 					nand-on-flash-bbt;
diff --git a/arch/arm/boot/dts/tny_a9g20.dts b/arch/arm/boot/dts/microchip/tny_a9g20.dts
index 118d766a1265..cebd5696a2c1 100644
--- a/arch/arm/boot/dts/tny_a9g20.dts
+++ b/arch/arm/boot/dts/microchip/tny_a9g20.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * tny_a9g20.dts - Device Tree file for Caloa TNY A9G20 board
+ * tny_a9g20.dts - Device Tree file for Calao TNY A9G20 board
  *
  * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
  */
diff --git a/arch/arm/boot/dts/usb_a9260.dts b/arch/arm/boot/dts/microchip/usb_a9260.dts
index 6cfa83921ac2..3b61e7145060 100644
--- a/arch/arm/boot/dts/usb_a9260.dts
+++ b/arch/arm/boot/dts/microchip/usb_a9260.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-or-later
 /*
- * usb_a9260.dts - Device Tree file for Caloa USB A9260 board
+ * usb_a9260.dts - Device Tree file for Calao USB A9260 board
  *
  *  Copyright (C) 2011-2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
  */
@@ -12,17 +12,9 @@
 	model = "Calao USB A9260";
 	compatible = "calao,usb-a9260", "atmel,at91sam9260", "atmel,at91sam9";
 
-	chosen {
-		bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock5 rw rootfstype=ubifs";
-	};
-
-	memory@20000000 {
-		reg = <0x20000000 0x4000000>;
-	};
-
 	ahb {
 		apb {
-			shdwc@fffffd10 {
+			shdwc: poweroff@fffffd10 {
 				atmel,wakeup-counter = <10>;
 				atmel,wakeup-rtt-timer;
 			};
diff --git a/arch/arm/boot/dts/usb_a9260_common.dtsi b/arch/arm/boot/dts/microchip/usb_a9260_common.dtsi
index 8744b5f6f792..da32c5fdcc47 100644
--- a/arch/arm/boot/dts/usb_a9260_common.dtsi
+++ b/arch/arm/boot/dts/microchip/usb_a9260_common.dtsi
@@ -1,11 +1,16 @@
 // SPDX-License-Identifier: GPL-2.0-or-later
 /*
- * usb_a926x.dts - Device Tree file for Caloa USB A926x board
+ * usb_a926x.dts - Device Tree file for Calao USB A926x board
  *
  *  Copyright (C) 2011-2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
  */
 
 / {
+	chosen {
+		bootargs = "mem=64M root=/dev/mtdblock5 rw rootfstype=ubifs";
+		stdout-path = "serial0:115200n8";
+	};
+
 	clocks {
 		slow_xtal {
 			clock-frequency = <32768>;
@@ -16,6 +21,10 @@
 		};
 	};
 
+	memory@20000000 {
+		reg = <0x20000000 0x4000000>;
+	};
+
 	ahb {
 		apb {
 			dbgu: serial@fffff200 {
@@ -111,7 +120,7 @@
 			};
 		};
 
-		usb0: ohci@500000 {
+		usb0: usb@500000 {
 			num-ports = <2>;
 			status = "okay";
 		};
@@ -122,17 +131,14 @@
 
 		user_led {
 			label = "user_led";
-			gpios = <&pioB 21 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "heartbeat";
+			gpios = <&pioB 21 GPIO_ACTIVE_HIGH>;
 		};
 	};
 
 	gpio_keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		user_pb {
+		button-user-pb {
 			label = "user_pb";
 			gpios = <&pioB 10 GPIO_ACTIVE_LOW>;
 			linux,code = <28>;
diff --git a/arch/arm/boot/dts/usb_a9263.dts b/arch/arm/boot/dts/microchip/usb_a9263.dts
index 8a0cfbfd0c45..8e1a3fb61087 100644
--- a/arch/arm/boot/dts/usb_a9263.dts
+++ b/arch/arm/boot/dts/microchip/usb_a9263.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * usb_a9263.dts - Device Tree file for Caloa USB A9293 board
+ * usb_a9263.dts - Device Tree file for Calao USB A9293 board
  *
  *  Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
  */
@@ -9,7 +9,7 @@
 
 / {
 	model = "Calao USB A9263";
-	compatible = "atmel,usb-a9263", "atmel,at91sam9263", "atmel,at91sam9";
+	compatible = "calao,usb-a9263", "atmel,at91sam9263", "atmel,at91sam9";
 
 	chosen {
 		bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock5 rw rootfstype=ubifs";
@@ -58,16 +58,16 @@
 			};
 
 			spi0: spi@fffa4000 {
-				cs-gpios = <&pioB 15 GPIO_ACTIVE_HIGH>;
+				cs-gpios = <&pioA 5 GPIO_ACTIVE_LOW>;
 				status = "okay";
-				mtd_dataflash@0 {
+				flash@0 {
 					compatible = "atmel,at45", "atmel,dataflash";
 					reg = <0>;
 					spi-max-frequency = <15000000>;
 				};
 			};
 
-			shdwc@fffffd10 {
+			poweroff@fffffd10 {
 				atmel,wakeup-counter = <10>;
 				atmel,wakeup-rtt-timer;
 			};
@@ -84,7 +84,7 @@
 				nand@3 {
 					reg = <0x3 0x0 0x800000>;
 					rb-gpios = <&pioA 22 GPIO_ACTIVE_HIGH>;
-					cs-gpios = <&pioA 15 GPIO_ACTIVE_HIGH>;
+					cs-gpios = <&pioD 15 GPIO_ACTIVE_HIGH>;
 					nand-bus-width = <8>;
 					nand-ecc-mode = "soft";
 					nand-on-flash-bbt;
@@ -139,7 +139,7 @@
 			};
 		};
 
-		usb0: ohci@a00000 {
+		usb0: usb@a00000 {
 			num-ports = <2>;
 			status = "okay";
 		};
@@ -151,16 +151,13 @@
 		user_led {
 			label = "user_led";
 			gpios = <&pioB 21 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
 		};
 	};
 
 	gpio_keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		user_pb {
+		button-user-pb {
 			label = "user_pb";
 			gpios = <&pioB 10 GPIO_ACTIVE_LOW>;
 			linux,code = <28>;
diff --git a/arch/arm/boot/dts/usb_a9g20-dab-mmx.dtsi b/arch/arm/boot/dts/microchip/usb_a9g20-dab-mmx.dtsi
index 08d58081201a..5b1d80c0ab26 100644
--- a/arch/arm/boot/dts/usb_a9g20-dab-mmx.dtsi
+++ b/arch/arm/boot/dts/microchip/usb_a9g20-dab-mmx.dtsi
@@ -65,28 +65,26 @@
 
 	gpio_keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		user_pb1 {
+		button-user-pb1 {
 			label = "user_pb1";
 			gpios = <&pioB 25 GPIO_ACTIVE_LOW>;
 			linux,code = <0x100>;
 		};
 
-		user_pb2 {
+		button-user-pb2 {
 			label = "user_pb2";
 			gpios = <&pioB 13 GPIO_ACTIVE_LOW>;
 			linux,code = <0x101>;
 		};
 
-		user_pb3 {
+		button-user-pb3 {
 			label = "user_pb3";
 			gpios = <&pioA 26 GPIO_ACTIVE_LOW>;
 			linux,code = <0x102>;
 		};
 
-		user_pb4 {
+		button-user-pb4 {
 			label = "user_pb4";
 			gpios = <&pioC 9 GPIO_ACTIVE_LOW>;
 			linux,code = <0x103>;
diff --git a/arch/arm/boot/dts/microchip/usb_a9g20.dts b/arch/arm/boot/dts/microchip/usb_a9g20.dts
new file mode 100644
index 000000000000..555291cd30b3
--- /dev/null
+++ b/arch/arm/boot/dts/microchip/usb_a9g20.dts
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * usb_a9g20.dts - Device Tree file for Calao USB A9G20 board
+ *
+ *  Copyright (C) 2011 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ */
+/dts-v1/;
+#include "at91sam9g20.dtsi"
+#include "usb_a9260_common.dtsi"
+
+/ {
+	model = "Calao USB A9G20";
+	compatible = "calao,usb-a9g20", "atmel,at91sam9g20", "atmel,at91sam9";
+};
+
+&spi0 {
+	cs-gpios = <&pioC 11 GPIO_ACTIVE_LOW>;
+	status = "okay";
+	/* TODO: Some revisions might have a dataflash here instead of an EEPROM */
+	eeprom@0 {
+		compatible = "st,m95640", "atmel,at25";
+		reg = <0>;
+		spi-max-frequency = <2000000>;
+		size = <8192>;
+		pagesize = <32>;
+		address-width = <16>;
+	};
+};
diff --git a/arch/arm/boot/dts/usb_a9g20_lpw.dts b/arch/arm/boot/dts/microchip/usb_a9g20_lpw.dts
index f65712015d40..2eda00477bc5 100644
--- a/arch/arm/boot/dts/usb_a9g20_lpw.dts
+++ b/arch/arm/boot/dts/microchip/usb_a9g20_lpw.dts
@@ -1,11 +1,12 @@
 // SPDX-License-Identifier: GPL-2.0-or-later
 /*
- * usb_a9g20_lpw.dts - Device Tree file for Caloa USB A9G20 Low Power board
+ * usb_a9g20_lpw.dts - Device Tree file for Calao USB A9G20 Low Power board
  *
  *  Copyright (C) 2013 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
  */
 /dts-v1/;
-#include "usb_a9g20_common.dtsi"
+#include "at91sam9g20.dtsi"
+#include "usb_a9260_common.dtsi"
 
 / {
 	model = "Calao USB A9G20 Low Power";
@@ -16,7 +17,7 @@
 			spi1: spi@fffcc000 {
 				cs-gpios = <&pioB 3 GPIO_ACTIVE_HIGH>;
 				status = "okay";
-				mmc-slot@0 {
+				mmc@0 {
 					compatible = "mmc-spi-slot";
 					reg = <0>;
 					voltage-ranges = <3200 3400>;
@@ -27,4 +28,11 @@
 			};
 		};
 	};
+
+	i2c-gpio-0 {
+		rtc@56 {
+			compatible = "microcrystal,rv3029";
+			reg = <0x56>;
+		};
+	};
 };
diff --git a/arch/arm/boot/dts/moxa/Makefile b/arch/arm/boot/dts/moxa/Makefile
new file mode 100644
index 000000000000..d61ce8d4e732
--- /dev/null
+++ b/arch/arm/boot/dts/moxa/Makefile
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_MOXART) += \
+	moxart-uc7112lx.dtb
diff --git a/arch/arm/boot/dts/moxart-uc7112lx.dts b/arch/arm/boot/dts/moxa/moxart-uc7112lx.dts
index eb5291b0ee3a..e07b807b4cec 100644
--- a/arch/arm/boot/dts/moxart-uc7112lx.dts
+++ b/arch/arm/boot/dts/moxa/moxart-uc7112lx.dts
@@ -79,7 +79,7 @@
 	clocks = <&ref12>;
 };
 
-&sdhci {
+&mmc {
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/moxart.dtsi b/arch/arm/boot/dts/moxa/moxart.dtsi
index f5f070a87482..11cbea5b94d2 100644
--- a/arch/arm/boot/dts/moxart.dtsi
+++ b/arch/arm/boot/dts/moxa/moxart.dtsi
@@ -93,8 +93,8 @@
 			clock-names = "PCLK";
 		};
 
-		sdhci: sdhci@98e00000 {
-			compatible = "moxa,moxart-sdhci";
+		mmc: mmc@98e00000 {
+			compatible = "moxa,moxart-mmc";
 			reg = <0x98e00000 0x5C>;
 			interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clk_apb>;
@@ -138,7 +138,7 @@
 			status = "disabled";
 		};
 
-		uart0: uart@98200000 {
+		uart0: serial@98200000 {
 			compatible = "ns16550a";
 			reg = <0x98200000 0x20>;
 			interrupts = <31 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/mt7623a.dtsi b/arch/arm/boot/dts/mt7623a.dtsi
deleted file mode 100644
index d304b62d24b5..000000000000
--- a/arch/arm/boot/dts/mt7623a.dtsi
+++ /dev/null
@@ -1,48 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (c) 2017-2018 MediaTek Inc.
- * Author: Sean Wang <sean.wang@mediatek.com>
- *
- */
-
-/dts-v1/;
-#include <dt-bindings/power/mt7623a-power.h>
-#include "mt7623.dtsi"
-
-&afe {
-	power-domains = <&scpsys MT7623A_POWER_DOMAIN_IFR_MSC>;
-};
-
-&crypto {
-	power-domains = <&scpsys MT7623A_POWER_DOMAIN_ETH>;
-};
-
-&eth {
-	power-domains = <&scpsys MT7623A_POWER_DOMAIN_ETH>;
-};
-
-&nandc {
-	power-domains = <&scpsys MT7623A_POWER_DOMAIN_IFR_MSC>;
-};
-
-&pcie {
-	power-domains = <&scpsys MT7623A_POWER_DOMAIN_HIF>;
-};
-
-&scpsys {
-	compatible = "mediatek,mt7623a-scpsys";
-	clocks = <&topckgen CLK_TOP_ETHIF_SEL>;
-	clock-names = "ethif";
-};
-
-&usb0 {
-	power-domains = <&scpsys MT7623A_POWER_DOMAIN_IFR_MSC>;
-};
-
-&usb1 {
-	power-domains = <&scpsys MT7623A_POWER_DOMAIN_HIF>;
-};
-
-&usb2 {
-	power-domains = <&scpsys MT7623A_POWER_DOMAIN_HIF>;
-};
diff --git a/arch/arm/boot/dts/nspire-clp.dts b/arch/arm/boot/dts/nspire-clp.dts
deleted file mode 100644
index f52f38c61588..000000000000
--- a/arch/arm/boot/dts/nspire-clp.dts
+++ /dev/null
@@ -1,41 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- *  linux/arch/arm/boot/nspire-clp.dts
- *
- *  Copyright (C) 2013 Daniel Tang <tangrs@tangrs.id.au>
- */
-/dts-v1/;
-
-/include/ "nspire-classic.dtsi"
-
-&keypad {
-	linux,keymap = <
-	0x0000001c 	0x0001001c 	0x00020039
-	0x0004002c 	0x00050034 	0x00060015
-	0x0007000b 	0x0008002d 	0x01000033
-	0x0101004e 	0x01020011 	0x01030004
-	0x0104002f 	0x01050003 	0x01060016
-	0x01070002 	0x01080014 	0x02000062
-	0x0201000c 	0x0202001f 	0x02030007
-	0x02040013 	0x02050006 	0x02060010
-	0x02070005 	0x02080019 	0x03000027
-	0x03010037 	0x03020018 	0x0303000a
-	0x03040031 	0x03050009 	0x03060032
-	0x03070008 	0x03080026 	0x04000028
-	0x04010035 	0x04020025 	0x04040024
-	0x04060017 	0x04080023 	0x05000028
-	0x05020022 	0x0503001b 	0x05040021
-	0x0505001a 	0x05060012 	0x0507006f
-	0x05080020 	0x0509002a 	0x0601001c
-	0x0602002e 	0x06030068 	0x06040030
-	0x0605006d 	0x0606001e 	0x06070001
-	0x0608002b 	0x0609000f 	0x07000067
-	0x0702006a 	0x0704006c 	0x07060069
-	0x0707000e 	0x0708001d 	0x070a000d
-	>;
-};
-
-/ {
-	model = "TI-NSPIRE Clickpad";
-	compatible = "ti,nspire-clp";
-};
diff --git a/arch/arm/boot/dts/nspire-cx.dts b/arch/arm/boot/dts/nspire-cx.dts
deleted file mode 100644
index 0c16b04e2744..000000000000
--- a/arch/arm/boot/dts/nspire-cx.dts
+++ /dev/null
@@ -1,125 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- *  linux/arch/arm/boot/nspire-cx.dts
- *
- *  Copyright (C) 2013 Daniel Tang <tangrs@tangrs.id.au>
- */
-/dts-v1/;
-
-/include/ "nspire.dtsi"
-
-&lcd {
-	port {
-		clcd_pads: endpoint {
-			remote-endpoint = <&panel_in>;
-		};
-	};
-};
-
-&fast_timer {
-	/* compatible = "arm,sp804", "arm,primecell"; */
-};
-
-&uart {
-	compatible = "arm,pl011", "arm,primecell";
-
-	clocks = <&uart_clk>, <&apb_pclk>;
-	clock-names = "uart_clk", "apb_pclk";
-};
-
-&timer0 {
-	compatible = "arm,sp804", "arm,primecell";
-};
-
-&timer1 {
-	compatible = "arm,sp804", "arm,primecell";
-};
-
-&base_clk {
-	compatible = "lsi,nspire-cx-clock";
-};
-
-&ahb_clk {
-	compatible = "lsi,nspire-cx-ahb-divider";
-};
-
-&keypad {
-	linux,keymap = <
-	0x0000001c 	0x0001001c 	0x00040039
-	0x0005002c 	0x00060015 	0x0007000b
-	0x0008000f 	0x0100002d 	0x01010011
-	0x0102002f 	0x01030004 	0x01040016
-	0x01050014 	0x0106001f 	0x01070002
-	0x010a006a 	0x02000013 	0x02010010
-	0x02020019 	0x02030007 	0x02040018
-	0x02050031 	0x02060032 	0x02070005
-	0x02080028 	0x0209006c 	0x03000026
-	0x03010025 	0x03020024 	0x0303000a
-	0x03040017 	0x03050023 	0x03060022
-	0x03070008 	0x03080035 	0x03090069
-	0x04000021 	0x04010012 	0x04020020
-	0x0404002e 	0x04050030 	0x0406001e
-	0x0407000d 	0x04080037 	0x04090067
-	0x05010038 	0x0502000c 	0x0503001b
-	0x05040034 	0x0505001a 	0x05060006
-	0x05080027 	0x0509000e 	0x050a006f
-	0x0600002b 	0x0602004e 	0x06030068
-	0x06040003 	0x0605006d 	0x06060009
-	0x06070001 	0x0609000f 	0x0708002a
-	0x0709001d 	0x070a0033 	>;
-};
-
-&vbus_reg {
-	gpio = <&gpio 2 0>;
-};
-
-/ {
-	model = "TI-NSPIRE CX";
-	compatible = "ti,nspire-cx";
-
-	memory {
-		device_type = "memory";
-		reg = <0x10000000 0x4000000>; /* 64 MB */
-	};
-
-	uart_clk: uart_clk {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <12000000>;
-	};
-
-	ahb {
-		#address-cells = <1>;
-		#size-cells = <1>;
-
-		intc: interrupt-controller@DC000000 {
-			compatible = "arm,pl190-vic";
-			interrupt-controller;
-			reg = <0xDC000000 0x1000>;
-			#interrupt-cells = <1>;
-		};
-
-		apb@90000000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			i2c@90050000 {
-				compatible = "snps,designware-i2c";
-				reg = <0x90050000 0x1000>;
-				interrupts = <20>;
-			};
-		};
-	};
-
-	panel {
-		compatible = "ti,nspire-cx-lcd-panel";
-		port {
-			panel_in: endpoint {
-				remote-endpoint = <&clcd_pads>;
-			};
-		};
-	};
-	chosen {
-		bootargs = "debug earlyprintk console=tty0 console=ttyAMA0,115200n8 root=/dev/ram0";
-	};
-};
diff --git a/arch/arm/boot/dts/nspire-tp.dts b/arch/arm/boot/dts/nspire-tp.dts
deleted file mode 100644
index f7d0faacd4cc..000000000000
--- a/arch/arm/boot/dts/nspire-tp.dts
+++ /dev/null
@@ -1,40 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- *  linux/arch/arm/boot/nspire-tp.dts
- *
- *  Copyright (C) 2013 Daniel Tang <tangrs@tangrs.id.au>
- */
-/dts-v1/;
-
-/include/ "nspire-classic.dtsi"
-
-&keypad {
-	linux,keymap = <
-	0x0000001c 	0x0001001c 	0x00040039
-	0x0005002c 	0x00060015 	0x0007000b
-	0x0008000f 	0x0100002d 	0x01010011
-	0x0102002f 	0x01030004 	0x01040016
-	0x01050014 	0x0106001f 	0x01070002
-	0x010a006a 	0x02000013 	0x02010010
-	0x02020019 	0x02030007 	0x02040018
-	0x02050031 	0x02060032 	0x02070005
-	0x02080028 	0x0209006c 	0x03000026
-	0x03010025 	0x03020024 	0x0303000a
-	0x03040017 	0x03050023 	0x03060022
-	0x03070008 	0x03080035 	0x03090069
-	0x04000021 	0x04010012 	0x04020020
-	0x0404002e 	0x04050030 	0x0406001e
-	0x0407000d 	0x04080037 	0x04090067
-	0x05010038 	0x0502000c 	0x0503001b
-	0x05040034 	0x0505001a 	0x05060006
-	0x05080027 	0x0509000e 	0x050a006f
-	0x0600002b 	0x0602004e 	0x06030068
-	0x06040003 	0x0605006d 	0x06060009
-	0x06070001 	0x0609000f 	0x0708002a
-	0x0709001d 	0x070a0033 	>;
-};
-
-/ {
-	model = "TI-NSPIRE Touchpad";
-	compatible = "ti,nspire-tp";
-};
diff --git a/arch/arm/boot/dts/nspire/Makefile b/arch/arm/boot/dts/nspire/Makefile
new file mode 100644
index 000000000000..82a2515bdd46
--- /dev/null
+++ b/arch/arm/boot/dts/nspire/Makefile
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_NSPIRE) += \
+	nspire-cx.dtb \
+	nspire-tp.dtb \
+	nspire-clp.dtb
diff --git a/arch/arm/boot/dts/nspire-classic.dtsi b/arch/arm/boot/dts/nspire/nspire-classic.dtsi
index 41744cc2bc72..0ee53d3ecd54 100644
--- a/arch/arm/boot/dts/nspire-classic.dtsi
+++ b/arch/arm/boot/dts/nspire/nspire-classic.dtsi
@@ -1,7 +1,5 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- *  linux/arch/arm/boot/nspire-classic.dts
- *
  *  Copyright (C) 2013 Daniel Tang <tangrs@tangrs.id.au>
  */
 
@@ -17,7 +15,7 @@
 
 &fast_timer {
 	/* compatible = "lsi,zevio-timer"; */
-	reg = <0x90010000 0x1000>, <0x900A0010 0x8>;
+	reg = <0x90010000 0x1000>, <0x900a0010 0x8>;
 };
 
 &uart {
@@ -30,12 +28,12 @@
 
 &timer0 {
 	/* compatible = "lsi,zevio-timer"; */
-	reg = <0x900C0000 0x1000>, <0x900A0018 0x8>;
+	reg = <0x900c0000 0x1000>, <0x900a0018 0x8>;
 };
 
 &timer1 {
 	compatible = "lsi,zevio-timer";
-	reg = <0x900D0000 0x1000>, <0x900A0020 0x8>;
+	reg = <0x900d0000 0x1000>, <0x900a0020 0x8>;
 };
 
 &keypad {
@@ -57,7 +55,7 @@
 };
 
 / {
-	memory {
+	memory@10000000 {
 		device_type = "memory";
 		reg = <0x10000000 0x2000000>; /* 32 MB */
 	};
@@ -66,10 +64,10 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 
-		intc: interrupt-controller@DC000000 {
+		intc: interrupt-controller@dc000000 {
 			compatible = "lsi,zevio-intc";
 			interrupt-controller;
-			reg = <0xDC000000 0x1000>;
+			reg = <0xdc000000 0x1000>;
 			#interrupt-cells = <1>;
 		};
 	};
diff --git a/arch/arm/boot/dts/nspire/nspire-clp.dts b/arch/arm/boot/dts/nspire/nspire-clp.dts
new file mode 100644
index 000000000000..c5773f770fd4
--- /dev/null
+++ b/arch/arm/boot/dts/nspire/nspire-clp.dts
@@ -0,0 +1,86 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *  Copyright (C) 2013 Daniel Tang <tangrs@tangrs.id.au>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+
+/include/ "nspire-classic.dtsi"
+
+&keypad {
+	linux,keymap = <
+		MATRIX_KEY(0,  0, 0x1c)
+		MATRIX_KEY(0,  1, 0x1c)
+		MATRIX_KEY(0,  2, 0x39)
+		MATRIX_KEY(0,  4, 0x2c)
+		MATRIX_KEY(0,  5, 0x34)
+		MATRIX_KEY(0,  6, 0x15)
+		MATRIX_KEY(0,  7, 0x0b)
+		MATRIX_KEY(0,  8, 0x2d)
+		MATRIX_KEY(1,  0, 0x33)
+		MATRIX_KEY(1,  1, 0x4e)
+		MATRIX_KEY(1,  2, 0x11)
+		MATRIX_KEY(1,  3, 0x04)
+		MATRIX_KEY(1,  4, 0x2f)
+		MATRIX_KEY(1,  5, 0x03)
+		MATRIX_KEY(1,  6, 0x16)
+		MATRIX_KEY(1,  7, 0x02)
+		MATRIX_KEY(1,  8, 0x14)
+		MATRIX_KEY(2,  0, 0x62)
+		MATRIX_KEY(2,  1, 0x0c)
+		MATRIX_KEY(2,  2, 0x1f)
+		MATRIX_KEY(2,  3, 0x07)
+		MATRIX_KEY(2,  4, 0x13)
+		MATRIX_KEY(2,  5, 0x06)
+		MATRIX_KEY(2,  6, 0x10)
+		MATRIX_KEY(2,  7, 0x05)
+		MATRIX_KEY(2,  8, 0x19)
+		MATRIX_KEY(3,  0, 0x27)
+		MATRIX_KEY(3,  1, 0x37)
+		MATRIX_KEY(3,  2, 0x18)
+		MATRIX_KEY(3,  3, 0x0a)
+		MATRIX_KEY(3,  4, 0x31)
+		MATRIX_KEY(3,  5, 0x09)
+		MATRIX_KEY(3,  6, 0x32)
+		MATRIX_KEY(3,  7, 0x08)
+		MATRIX_KEY(3,  8, 0x26)
+		MATRIX_KEY(4,  0, 0x28)
+		MATRIX_KEY(4,  1, 0x35)
+		MATRIX_KEY(4,  2, 0x25)
+		MATRIX_KEY(4,  4, 0x24)
+		MATRIX_KEY(4,  6, 0x17)
+		MATRIX_KEY(4,  8, 0x23)
+		MATRIX_KEY(5,  0, 0x28)
+		MATRIX_KEY(5,  2, 0x22)
+		MATRIX_KEY(5,  3, 0x1b)
+		MATRIX_KEY(5,  4, 0x21)
+		MATRIX_KEY(5,  5, 0x1a)
+		MATRIX_KEY(5,  6, 0x12)
+		MATRIX_KEY(5,  7, 0x6f)
+		MATRIX_KEY(5,  8, 0x20)
+		MATRIX_KEY(5,  9, 0x2a)
+		MATRIX_KEY(6,  1, 0x1c)
+		MATRIX_KEY(6,  2, 0x2e)
+		MATRIX_KEY(6,  3, 0x68)
+		MATRIX_KEY(6,  4, 0x30)
+		MATRIX_KEY(6,  5, 0x6d)
+		MATRIX_KEY(6,  6, 0x1e)
+		MATRIX_KEY(6,  7, 0x01)
+		MATRIX_KEY(6,  8, 0x2b)
+		MATRIX_KEY(6,  9, 0x0f)
+		MATRIX_KEY(7,  0, 0x67)
+		MATRIX_KEY(7,  2, 0x6a)
+		MATRIX_KEY(7,  4, 0x6c)
+		MATRIX_KEY(7,  6, 0x69)
+		MATRIX_KEY(7,  7, 0x0e)
+		MATRIX_KEY(7,  8, 0x1d)
+		MATRIX_KEY(7, 10, 0x0d)
+	>;
+};
+
+/ {
+	model = "TI-NSPIRE Clickpad";
+	compatible = "ti,nspire-clp";
+};
diff --git a/arch/arm/boot/dts/nspire/nspire-cx.dts b/arch/arm/boot/dts/nspire/nspire-cx.dts
new file mode 100644
index 000000000000..debeff0ec010
--- /dev/null
+++ b/arch/arm/boot/dts/nspire/nspire-cx.dts
@@ -0,0 +1,170 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *  Copyright (C) 2013 Daniel Tang <tangrs@tangrs.id.au>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+
+/include/ "nspire.dtsi"
+
+&lcd {
+	port {
+		clcd_pads: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
+};
+
+&fast_timer {
+	/* compatible = "arm,sp804", "arm,primecell"; */
+};
+
+&uart {
+	compatible = "arm,pl011", "arm,primecell";
+
+	clocks = <&uart_clk>, <&apb_pclk>;
+	clock-names = "uartclk", "apb_pclk";
+};
+
+&timer0 {
+	compatible = "arm,sp804", "arm,primecell";
+};
+
+&timer1 {
+	compatible = "arm,sp804", "arm,primecell";
+};
+
+&base_clk {
+	compatible = "lsi,nspire-cx-clock";
+};
+
+&ahb_clk {
+	compatible = "lsi,nspire-cx-ahb-divider";
+};
+
+&keypad {
+	linux,keymap = <
+		MATRIX_KEY(0,  0, 0x1c)
+		MATRIX_KEY(0,  1, 0x1c)
+		MATRIX_KEY(0,  4, 0x39)
+		MATRIX_KEY(0,  5, 0x2c)
+		MATRIX_KEY(0,  6, 0x15)
+		MATRIX_KEY(0,  7, 0x0b)
+		MATRIX_KEY(0,  8, 0x0f)
+		MATRIX_KEY(1,  0, 0x2d)
+		MATRIX_KEY(1,  1, 0x11)
+		MATRIX_KEY(1,  2, 0x2f)
+		MATRIX_KEY(1,  3, 0x04)
+		MATRIX_KEY(1,  4, 0x16)
+		MATRIX_KEY(1,  5, 0x14)
+		MATRIX_KEY(1,  6, 0x1f)
+		MATRIX_KEY(1,  7, 0x02)
+		MATRIX_KEY(1, 10, 0x6a)
+		MATRIX_KEY(2,  0, 0x13)
+		MATRIX_KEY(2,  1, 0x10)
+		MATRIX_KEY(2,  2, 0x19)
+		MATRIX_KEY(2,  3, 0x07)
+		MATRIX_KEY(2,  4, 0x18)
+		MATRIX_KEY(2,  5, 0x31)
+		MATRIX_KEY(2,  6, 0x32)
+		MATRIX_KEY(2,  7, 0x05)
+		MATRIX_KEY(2,  8, 0x28)
+		MATRIX_KEY(2,  9, 0x6c)
+		MATRIX_KEY(3,  0, 0x26)
+		MATRIX_KEY(3,  1, 0x25)
+		MATRIX_KEY(3,  2, 0x24)
+		MATRIX_KEY(3,  3, 0x0a)
+		MATRIX_KEY(3,  4, 0x17)
+		MATRIX_KEY(3,  5, 0x23)
+		MATRIX_KEY(3,  6, 0x22)
+		MATRIX_KEY(3,  7, 0x08)
+		MATRIX_KEY(3,  8, 0x35)
+		MATRIX_KEY(3,  9, 0x69)
+		MATRIX_KEY(4,  0, 0x21)
+		MATRIX_KEY(4,  1, 0x12)
+		MATRIX_KEY(4,  2, 0x20)
+		MATRIX_KEY(4,  4, 0x2e)
+		MATRIX_KEY(4,  5, 0x30)
+		MATRIX_KEY(4,  6, 0x1e)
+		MATRIX_KEY(4,  7, 0x0d)
+		MATRIX_KEY(4,  8, 0x37)
+		MATRIX_KEY(4,  9, 0x67)
+		MATRIX_KEY(5,  1, 0x38)
+		MATRIX_KEY(5,  2, 0x0c)
+		MATRIX_KEY(5,  3, 0x1b)
+		MATRIX_KEY(5,  4, 0x34)
+		MATRIX_KEY(5,  5, 0x1a)
+		MATRIX_KEY(5,  6, 0x06)
+		MATRIX_KEY(5,  8, 0x27)
+		MATRIX_KEY(5,  9, 0x0e)
+		MATRIX_KEY(5, 10, 0x6f)
+		MATRIX_KEY(6,  0, 0x2b)
+		MATRIX_KEY(6,  2, 0x4e)
+		MATRIX_KEY(6,  3, 0x68)
+		MATRIX_KEY(6,  4, 0x03)
+		MATRIX_KEY(6,  5, 0x6d)
+		MATRIX_KEY(6,  6, 0x09)
+		MATRIX_KEY(6,  7, 0x01)
+		MATRIX_KEY(6,  9, 0x0f)
+		MATRIX_KEY(7,  8, 0x2a)
+		MATRIX_KEY(7,  9, 0x1d)
+		MATRIX_KEY(7, 10, 0x33)
+	>;
+};
+
+&vbus_reg {
+	gpio = <&gpio 2 0>;
+};
+
+/ {
+	model = "TI-NSPIRE CX";
+	compatible = "ti,nspire-cx";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x4000000>; /* 64 MB */
+	};
+
+	uart_clk: uart_clk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <12000000>;
+	};
+
+	ahb {
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		intc: interrupt-controller@dc000000 {
+			compatible = "arm,pl190-vic";
+			interrupt-controller;
+			reg = <0xdc000000 0x1000>;
+			#interrupt-cells = <1>;
+		};
+
+		apb@90000000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			i2c@90050000 {
+				compatible = "snps,designware-i2c";
+				reg = <0x90050000 0x1000>;
+				interrupts = <20>;
+			};
+		};
+	};
+
+	panel {
+		compatible = "ti,nspire-cx-lcd-panel";
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&clcd_pads>;
+			};
+		};
+	};
+	chosen {
+		bootargs = "debug earlyprintk console=tty0 console=ttyAMA0,115200n8 root=/dev/ram0";
+	};
+};
diff --git a/arch/arm/boot/dts/nspire/nspire-tp.dts b/arch/arm/boot/dts/nspire/nspire-tp.dts
new file mode 100644
index 000000000000..3f0107f1c2c7
--- /dev/null
+++ b/arch/arm/boot/dts/nspire/nspire-tp.dts
@@ -0,0 +1,85 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *  Copyright (C) 2013 Daniel Tang <tangrs@tangrs.id.au>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+
+/include/ "nspire-classic.dtsi"
+
+&keypad {
+	linux,keymap = <
+		MATRIX_KEY(0,  0, 0x1c)
+		MATRIX_KEY(0,  1, 0x1c)
+		MATRIX_KEY(0,  4, 0x39)
+		MATRIX_KEY(0,  5, 0x2c)
+		MATRIX_KEY(0,  6, 0x15)
+		MATRIX_KEY(0,  7, 0x0b)
+		MATRIX_KEY(0,  8, 0x0f)
+		MATRIX_KEY(1,  0, 0x2d)
+		MATRIX_KEY(1,  1, 0x11)
+		MATRIX_KEY(1,  2, 0x2f)
+		MATRIX_KEY(1,  3, 0x04)
+		MATRIX_KEY(1,  4, 0x16)
+		MATRIX_KEY(1,  5, 0x14)
+		MATRIX_KEY(1,  6, 0x1f)
+		MATRIX_KEY(1,  7, 0x02)
+		MATRIX_KEY(1, 10, 0x6a)
+		MATRIX_KEY(2,  0, 0x13)
+		MATRIX_KEY(2,  1, 0x10)
+		MATRIX_KEY(2,  2, 0x19)
+		MATRIX_KEY(2,  3, 0x07)
+		MATRIX_KEY(2,  4, 0x18)
+		MATRIX_KEY(2,  5, 0x31)
+		MATRIX_KEY(2,  6, 0x32)
+		MATRIX_KEY(2,  7, 0x05)
+		MATRIX_KEY(2,  8, 0x28)
+		MATRIX_KEY(2,  9, 0x6c)
+		MATRIX_KEY(3,  0, 0x26)
+		MATRIX_KEY(3,  1, 0x25)
+		MATRIX_KEY(3,  2, 0x24)
+		MATRIX_KEY(3,  3, 0x0a)
+		MATRIX_KEY(3,  4, 0x17)
+		MATRIX_KEY(3,  5, 0x23)
+		MATRIX_KEY(3,  6, 0x22)
+		MATRIX_KEY(3,  7, 0x08)
+		MATRIX_KEY(3,  8, 0x35)
+		MATRIX_KEY(3,  9, 0x69)
+		MATRIX_KEY(4,  0, 0x21)
+		MATRIX_KEY(4,  1, 0x12)
+		MATRIX_KEY(4,  2, 0x20)
+		MATRIX_KEY(4,  4, 0x2e)
+		MATRIX_KEY(4,  5, 0x30)
+		MATRIX_KEY(4,  6, 0x1e)
+		MATRIX_KEY(4,  7, 0x0d)
+		MATRIX_KEY(4,  8, 0x37)
+		MATRIX_KEY(4,  9, 0x67)
+		MATRIX_KEY(5,  1, 0x38)
+		MATRIX_KEY(5,  2, 0x0c)
+		MATRIX_KEY(5,  3, 0x1b)
+		MATRIX_KEY(5,  4, 0x34)
+		MATRIX_KEY(5,  5, 0x1a)
+		MATRIX_KEY(5,  6, 0x06)
+		MATRIX_KEY(5,  8, 0x27)
+		MATRIX_KEY(5,  9, 0x0e)
+		MATRIX_KEY(5, 10, 0x6f)
+		MATRIX_KEY(6,  0, 0x2b)
+		MATRIX_KEY(6,  2, 0x4e)
+		MATRIX_KEY(6,  3, 0x68)
+		MATRIX_KEY(6,  4, 0x03)
+		MATRIX_KEY(6,  5, 0x6d)
+		MATRIX_KEY(6,  6, 0x09)
+		MATRIX_KEY(6,  7, 0x01)
+		MATRIX_KEY(6,  9, 0x0f)
+		MATRIX_KEY(7,  8, 0x2a)
+		MATRIX_KEY(7,  9, 0x1d)
+		MATRIX_KEY(7, 10, 0x33)
+	>;
+};
+
+/ {
+	model = "TI-NSPIRE Touchpad";
+	compatible = "ti,nspire-tp";
+};
diff --git a/arch/arm/boot/dts/nspire.dtsi b/arch/arm/boot/dts/nspire/nspire.dtsi
index 90e033d9141f..95588b716c6f 100644
--- a/arch/arm/boot/dts/nspire.dtsi
+++ b/arch/arm/boot/dts/nspire/nspire.dtsi
@@ -1,7 +1,5 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- *  linux/arch/arm/boot/nspire.dtsi
- *
  *  Copyright (C) 2013 Daniel Tang <tangrs@tangrs.id.au>
  */
 
@@ -11,8 +9,13 @@
 	interrupt-parent = <&intc>;
 
 	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
 		cpu@0 {
 			compatible = "arm,arm926ej-s";
+			device_type = "cpu";
+			reg = <0>;
 		};
 	};
 
@@ -20,9 +23,16 @@
 		reg = <0x00000000 0x80000>;
 	};
 
-	sram: sram@A4000000 {
-		device = "memory";
-		reg = <0xA4000000 0x20000>;
+	sram: sram@a4000000 {
+		compatible = "mmio-sram";
+		reg = <0xa4000000 0x20000>; /* 128k */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xa4000000 0x20000>;
+
+		sram@0 {
+			reg = <0x0 0x20000>;
+		};
 	};
 
 	timer_clk: timer_clk {
@@ -33,12 +43,12 @@
 
 	base_clk: base_clk {
 		#clock-cells = <0>;
-		reg = <0x900B0024 0x4>;
+		reg = <0x900b0024 0x4>;
 	};
 
 	ahb_clk: ahb_clk {
 		#clock-cells = <0>;
-		reg = <0x900B0024 0x4>;
+		reg = <0x900b0024 0x4>;
 		clocks = <&base_clk>;
 	};
 
@@ -59,7 +69,6 @@
 		compatible = "regulator-fixed";
 
 		regulator-name = "USB VBUS output";
-		regulator-type = "voltage";
 
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
@@ -71,28 +80,28 @@
 		#size-cells = <1>;
 		ranges;
 
-		spi: spi@A9000000 {
-			reg = <0xA9000000 0x1000>;
+		spi: spi@a9000000 {
+			reg = <0xa9000000 0x1000>;
 		};
 
-		usb0: usb@B0000000 {
+		usb0: usb@b0000000 {
 			compatible = "lsi,zevio-usb";
-			reg = <0xB0000000 0x1000>;
+			reg = <0xb0000000 0x1000>;
 			interrupts = <8>;
 
 			usb-phy = <&usb_phy>;
 			vbus-supply = <&vbus_reg>;
 		};
 
-		usb1: usb@B4000000 {
-			reg = <0xB4000000 0x1000>;
+		usb1: usb@b4000000 {
+			reg = <0xb4000000 0x1000>;
 			interrupts = <9>;
 			status = "disabled";
 		};
 
-		lcd: lcd@C0000000 {
+		lcd: lcd@c0000000 {
 			compatible = "arm,pl111", "arm,primecell";
-			reg = <0xC0000000 0x1000>;
+			reg = <0xc0000000 0x1000>;
 			interrupts = <21>;
 
 			/*
@@ -105,17 +114,17 @@
 			clock-names = "clcdclk", "apb_pclk";
 		};
 
-		adc: adc@C4000000 {
-			reg = <0xC4000000 0x1000>;
+		adc: adc@c4000000 {
+			reg = <0xc4000000 0x1000>;
 			interrupts = <11>;
 		};
 
-		tdes: crypto@C8010000 {
-			reg = <0xC8010000 0x1000>;
+		tdes: crypto@c8010000 {
+			reg = <0xc8010000 0x1000>;
 		};
 
-		sha256: crypto@CC000000 {
-			reg = <0xCC000000 0x1000>;
+		sha256: crypto@cc000000 {
+			reg = <0xcc000000 0x1000>;
 		};
 
 		apb@90000000 {
@@ -143,16 +152,16 @@
 				interrupts = <1>;
 			};
 
-			timer0: timer@900C0000 {
-				reg = <0x900C0000 0x1000>;
+			timer0: timer@900c0000 {
+				reg = <0x900c0000 0x1000>;
 				clocks = <&timer_clk>, <&timer_clk>,
 					 <&timer_clk>;
 				clock-names = "timer0clk", "timer1clk",
 					      "apb_pclk";
 			};
 
-			timer1: timer@900D0000 {
-				reg = <0x900D0000 0x1000>;
+			timer1: timer@900d0000 {
+				reg = <0x900d0000 0x1000>;
 				interrupts = <19>;
 				clocks = <&timer_clk>, <&timer_clk>,
 					 <&timer_clk>;
@@ -161,9 +170,12 @@
 			};
 
 			watchdog: watchdog@90060000 {
-				compatible = "arm,amba-primecell";
+				compatible = "arm,sp805", "arm,primecell";
 				reg = <0x90060000 0x1000>;
 				interrupts = <3>;
+				clocks = <&apb_pclk>, <&apb_pclk>;
+				clock-names = "wdog_clk", "apb_pclk";
+				status = "disabled";
 			};
 
 			rtc: rtc@90090000 {
@@ -171,18 +183,25 @@
 				interrupts = <4>;
 			};
 
-			misc: misc@900A0000 {
-				reg = <0x900A0000 0x1000>;
+			misc: misc@900a0000 {
+				compatible = "ti,nspire-misc", "syscon", "simple-mfd";
+				reg = <0x900a0000 0x1000>;
+
+				reboot {
+					compatible = "syscon-reboot";
+					offset = <0x08>;
+					value = <0x02>;
+				};
 			};
 
-			pwr: pwr@900B0000 {
-				reg = <0x900B0000 0x1000>;
+			pwr: pwr@900b0000 {
+				reg = <0x900b0000 0x1000>;
 				interrupts = <15>;
 			};
 
-			keypad: input@900E0000 {
+			keypad: input@900e0000 {
 				compatible = "ti,nspire-keypad";
-				reg = <0x900E0000 0x1000>;
+				reg = <0x900e0000 0x1000>;
 				interrupts = <16>;
 
 				scan-interval = <1000>;
@@ -191,8 +210,8 @@
 				clocks = <&apb_pclk>;
 			};
 
-			contrast: contrast@900F0000 {
-				reg = <0x900F0000 0x1000>;
+			contrast: contrast@900f0000 {
+				reg = <0x900f0000 0x1000>;
 			};
 
 			led: led@90110000 {
diff --git a/arch/arm/boot/dts/nuvoton-npcm750.dtsi b/arch/arm/boot/dts/nuvoton-npcm750.dtsi
deleted file mode 100644
index 13eee0fe5642..000000000000
--- a/arch/arm/boot/dts/nuvoton-npcm750.dtsi
+++ /dev/null
@@ -1,62 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-// Copyright (c) 2018 Nuvoton Technology tomer.maimon@nuvoton.com
-// Copyright 2018 Google, Inc.
-
-#include "nuvoton-common-npcm7xx.dtsi"
-
-/ {
-	#address-cells = <1>;
-	#size-cells = <1>;
-	interrupt-parent = <&gic>;
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		enable-method = "nuvoton,npcm750-smp";
-
-		cpu@0 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a9";
-			clocks = <&clk NPCM7XX_CLK_CPU>;
-			clock-names = "clk_cpu";
-			reg = <0>;
-			next-level-cache = <&l2>;
-		};
-
-		cpu@1 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a9";
-			clocks = <&clk NPCM7XX_CLK_CPU>;
-			clock-names = "clk_cpu";
-			reg = <1>;
-			next-level-cache = <&l2>;
-		};
-	};
-
-	soc {
-		timer@3fe600 {
-			compatible = "arm,cortex-a9-twd-timer";
-			reg = <0x3fe600 0x20>;
-			interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) |
-						  IRQ_TYPE_LEVEL_HIGH)>;
-			clocks = <&clk NPCM7XX_CLK_AHB>;
-		};
-	};
-
-	ahb {
-		gmac1: eth@f0804000 {
-			device_type = "network";
-			compatible = "snps,dwmac";
-			reg = <0xf0804000 0x2000>;
-			interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "macirq";
-			ethernet = <1>;
-			clocks	= <&clk_rg2refck>, <&clk NPCM7XX_CLK_AHB>;
-			clock-names = "stmmaceth", "clk_gmac";
-			pinctrl-names = "default";
-			pinctrl-0 = <&rg2_pins
-					&rg2mdio_pins>;
-			status = "disabled";
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/nuvoton/Makefile b/arch/arm/boot/dts/nuvoton/Makefile
new file mode 100644
index 000000000000..89c157dad312
--- /dev/null
+++ b/arch/arm/boot/dts/nuvoton/Makefile
@@ -0,0 +1,9 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_NPCM7XX) += \
+	nuvoton-npcm730-gsj.dtb \
+	nuvoton-npcm730-gbs.dtb \
+	nuvoton-npcm730-kudo.dtb \
+	nuvoton-npcm750-evb.dtb \
+	nuvoton-npcm750-runbmc-olympus.dtb
+dtb-$(CONFIG_ARCH_WPCM450) += \
+	nuvoton-wpcm450-supermicro-x9sci-ln4f.dtb
diff --git a/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi b/arch/arm/boot/dts/nuvoton/nuvoton-common-npcm7xx.dtsi
index 3696980a3da1..98c35771534e 100644
--- a/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-common-npcm7xx.dtsi
@@ -99,6 +99,11 @@
 		};
 	};
 
+	udc0_phy: usb-phy {
+		compatible = "usb-nop-xceiv";
+		#phy-cells = <0>;
+	};
+
 	ahb {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -110,6 +115,7 @@
 			compatible = "nuvoton,npcm750-reset";
 			reg = <0xf0801000 0x70>;
 			#reset-cells = <2>;
+			nuvoton,sysgcr = <&gcr>;
 		};
 
 		clk: clock-controller@f0801000 {
@@ -121,14 +127,21 @@
 			clocks = <&clk_refclk>, <&clk_sysbypck>, <&clk_mcbypck>;
 		};
 
-		gmac0: eth@f0802000 {
+		mc: memory-controller@f0824000 {
+			compatible = "nuvoton,npcm750-memory-controller";
+			reg = <0xf0824000 0x1000>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		gmac0: ethernet@f0802000 {
 			device_type = "network";
 			compatible = "snps,dwmac";
 			reg = <0xf0802000 0x2000>;
 			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "macirq";
 			ethernet = <0>;
-			clocks	= <&clk_rg1refck>, <&clk NPCM7XX_CLK_AHB>;
+			clocks = <&clk_rg1refck>, <&clk NPCM7XX_CLK_AHB>;
 			clock-names = "stmmaceth", "clk_gmac";
 			pinctrl-names = "default";
 			pinctrl-0 = <&rg1_pins
@@ -136,6 +149,29 @@
 			status = "disabled";
 		};
 
+		sdmmc: mmc@f0842000 {
+			compatible = "nuvoton,npcm750-sdhci";
+			status = "disabled";
+			reg = <0xf0842000 0x200>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+			clocks =  <&clk NPCM7XX_CLK_AHB>;
+			clock-names = "clk_mmc";
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc8_pins
+					&mmc_pins>;
+		};
+
+		sdhci: mmc@f0840000 {
+			compatible = "nuvoton,npcm750-sdhci";
+			status = "disabled";
+			reg = <0xf0840000 0x200>;
+			interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+			clocks =  <&clk NPCM7XX_CLK_AHB>;
+			clock-names = "clk_sdhc";
+			pinctrl-names = "default";
+			pinctrl-0 = <&sd1_pins>;
+		};
+
 		ehci1: usb@f0806000 {
 			compatible = "nuvoton,npcm750-ehci";
 			reg = <0xf0806000 0x1000>;
@@ -143,6 +179,13 @@
 			status = "disabled";
 		};
 
+		ohci1: usb@f0807000 {
+			compatible = "generic-ohci";
+			reg = <0xf0807000 0x1000>;
+			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
 		fiu0: spi@fb000000 {
 			compatible = "nuvoton,npcm750-fiu";
 			#address-cells = <1>;
@@ -178,6 +221,72 @@
 			status = "disabled";
 		};
 
+		udc5: usb@f0835000 {
+			compatible = "nuvoton,npcm750-udc";
+			reg = <0xf0835000 0x1000
+			       0xfffd2800 0x800>;
+			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM7XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc6: usb@f0836000 {
+			compatible = "nuvoton,npcm750-udc";
+			reg = <0xf0836000 0x1000
+			       0xfffd3000 0x800>;
+			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM7XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc7: usb@f0837000 {
+			compatible = "nuvoton,npcm750-udc";
+			reg = <0xf0837000 0x1000
+			       0xfffd3800 0x800>;
+			interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM7XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc8: usb@f0838000 {
+			compatible = "nuvoton,npcm750-udc";
+			reg = <0xf0838000 0x1000
+			       0xfffd4000 0x800>;
+			interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM7XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc9: usb@f0839000 {
+			compatible = "nuvoton,npcm750-udc";
+			reg = <0xf0839000 0x1000
+			       0xfffd4800 0x800>;
+			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM7XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+			nuvoton,sysgcr = <&gcr>;
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
 		apb {
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -219,6 +328,15 @@
 				};
 			};
 
+			peci: peci-controller@f0100000 {
+				compatible = "nuvoton,npcm750-peci";
+				reg = <0xf0100000 0x200>;
+				interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk NPCM7XX_CLK_APB3>;
+				cmd-timeout-ms = <1000>;
+				status = "disabled";
+			};
+
 			spi0: spi@200000 {
 				compatible = "nuvoton,npcm750-pspi";
 				reg = <0x200000 0x1000>;
diff --git a/arch/arm/boot/dts/nuvoton-npcm730-gbs.dts b/arch/arm/boot/dts/nuvoton/nuvoton-npcm730-gbs.dts
index eb6eb21cb2a4..231228842e63 100644
--- a/arch/arm/boot/dts/nuvoton-npcm730-gbs.dts
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-npcm730-gbs.dts
@@ -358,7 +358,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&spi0cs1_pins>;
 	status = "okay";
-	spi-nor@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -366,7 +366,7 @@
 		spi-max-frequency = <20000000>;
 		spi-rx-bus-width = <2>;
 		label = "bmc";
-		partitions@80000000 {
+		partitions {
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -406,7 +406,7 @@
 	pinctrl-0 = <&spi3_pins>, <&spi3cs1_pins>;
 	status = "okay";
 
-	spi-nor@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -416,7 +416,7 @@
 		m25p,fast-read;
 		label = "pnor";
 	};
-	spi-nor@1 {
+	flash@1 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -525,7 +525,7 @@
 	clock-frequency = <100000>;
 	status = "okay";
 
-	i2c-switch@71 {
+	i2c-mux@71 {
 		compatible = "nxp,pca9546";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -661,12 +661,12 @@
 	clock-frequency = <100000>;
 	status = "okay";
 
-	mb_fru@50 {
+	eeprom@50 {
 		compatible = "atmel,24c64";
 		reg = <0x50>;
 	};
 
-	i2c-switch@71 {
+	i2c-mux@71 {
 		compatible = "nxp,pca9546";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -704,7 +704,7 @@
 				reg = <0x5d>;
 				status = "okay";
 			};
-			fan_fru@51 {
+			eeprom@51 {
 				compatible = "atmel,24c64";
 				reg = <0x51>;
 			};
@@ -714,7 +714,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <3>;
-			hsbp_fru@52 {
+			eeprom@52 {
 				compatible = "atmel,24c64";
 				reg = <0x52>;
 				status = "okay";
@@ -727,7 +727,7 @@
 	clock-frequency = <100000>;
 	status = "okay";
 
-	i2c-switch@73 {
+	i2c-mux@73 {
 		compatible = "nxp,pca9545";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -763,7 +763,7 @@
 	clock-frequency = <100000>;
 	status = "okay";
 
-	i2c-switch@72 {
+	i2c-mux@72 {
 		compatible = "nxp,pca9545";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -812,7 +812,7 @@
 	clock-frequency = <100000>;
 	status = "okay";
 
-	i2c-switch@71 {
+	i2c-mux@71 {
 		compatible = "nxp,pca9546";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -866,7 +866,7 @@
 	clock-frequency = <100000>;
 	status = "okay";
 
-	i2c-switch@71 {
+	i2c-mux@71 {
 		compatible = "nxp,pca9545";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -902,7 +902,7 @@
 	clock-frequency = <100000>;
 	status = "okay";
 
-	i2c-switch@76 {
+	i2c-mux@76 {
 		compatible = "nxp,pca9545";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -961,7 +961,7 @@
 	clock-frequency = <100000>;
 	status = "okay";
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9545";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -1050,19 +1050,19 @@
 		"","","","SIO_POWER_GOOD","","","","";
 	};
 	gpio2: gpio@f0012000 {
-		bmc_usb_mux_oe_n {
+		bmc-usb-mux-oe-n-hog {
 			gpio-hog;
 			gpios = <25 GPIO_ACTIVE_HIGH>;
 			output-low;
 			line-name = "bmc-usb-mux-oe-n";
 		};
-		bmc_usb_mux_sel {
+		bmc-usb-mux-sel-hog {
 			gpio-hog;
 			gpios = <26 GPIO_ACTIVE_HIGH>;
 			output-low;
 			line-name = "bmc-usb-mux-sel";
 		};
-		bmc_usb2517_reset_n {
+		bmc-usb2517-reset-n-hog {
 			gpio-hog;
 			gpios = <27 GPIO_ACTIVE_LOW>;
 			output-low;
@@ -1070,19 +1070,19 @@
 		};
 	};
 	gpio3: gpio@f0013000 {
-		assert_cpu0_reset {
+		assert-cpu0-reset-hog {
 			gpio-hog;
 			gpios = <14 GPIO_ACTIVE_HIGH>;
 			output-low;
 			line-name = "assert-cpu0-reset";
 		};
-		assert_pwrok_cpu0_n {
+		assert-pwrok-cpu0-n-hog {
 			gpio-hog;
 			gpios = <15 GPIO_ACTIVE_HIGH>;
 			output-low;
 			line-name = "assert-pwrok-cpu0-n";
 		};
-		assert_cpu0_prochot {
+		assert-cpu0-prochot-hog {
 			gpio-hog;
 			gpios = <16 GPIO_ACTIVE_HIGH>;
 			output-low;
diff --git a/arch/arm/boot/dts/nuvoton-npcm730-gsj-gpio.dtsi b/arch/arm/boot/dts/nuvoton/nuvoton-npcm730-gsj-gpio.dtsi
index 53cfd15fa03f..53cfd15fa03f 100644
--- a/arch/arm/boot/dts/nuvoton-npcm730-gsj-gpio.dtsi
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-npcm730-gsj-gpio.dtsi
diff --git a/arch/arm/boot/dts/nuvoton-npcm730-gsj.dts b/arch/arm/boot/dts/nuvoton/nuvoton-npcm730-gsj.dts
index d4ff49939a3d..cd7843339c24 100644
--- a/arch/arm/boot/dts/nuvoton-npcm730-gsj.dts
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-npcm730-gsj.dts
@@ -135,18 +135,18 @@
 	pinctrl-0 = <&spi0cs1_pins>;
 	status = "okay";
 
-	spi-nor@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		reg = <0>;
 		spi-rx-bus-width = <2>;
 
-		partitions@80000000 {
+		partitions {
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
 			#size-cells = <1>;
-			bmc@0{
+			bmc@0 {
 				label = "bmc";
 				reg = <0x000000 0x2000000>;
 			};
@@ -155,7 +155,7 @@
 				reg = <0x0000000 0x80000>;
 				read-only;
 			};
-			u-boot-env@100000{
+			u-boot-env@100000 {
 				label = "u-boot-env";
 				reg = <0x00100000 0x40000>;
 			};
@@ -303,7 +303,7 @@
 &i2c15 {
 	status = "okay";
 
-	i2c-switch@75 {
+	i2c-mux@75 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
diff --git a/arch/arm/boot/dts/nuvoton-npcm730-kudo.dts b/arch/arm/boot/dts/nuvoton/nuvoton-npcm730-kudo.dts
index 82a104b2a65f..886a87dfcd0d 100644
--- a/arch/arm/boot/dts/nuvoton-npcm730-kudo.dts
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-npcm730-kudo.dts
@@ -380,7 +380,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&spi0cs1_pins>;
 	status = "okay";
-	spi-nor@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -388,7 +388,7 @@
 		spi-max-frequency = <5000000>;
 		spi-rx-bus-width = <2>;
 		label = "bmc";
-		partitions@80000000 {
+		partitions {
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -397,7 +397,7 @@
 				reg = <0x0000000 0xC0000>;
 				read-only;
 			};
-			u-boot-env@100000{
+			u-boot-env@100000 {
 				label = "u-boot-env";
 				reg = <0x00100000 0x40000>;
 			};
@@ -415,14 +415,14 @@
 			};
 		};
 	};
-	spi-nor@1 {
+	flash@1 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		reg = <1>;
 		spi-max-frequency = <5000000>;
 		spi-rx-bus-width = <2>;
-		partitions@88000000 {
+		partitions {
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -440,14 +440,14 @@
 
 &fiu3 {
 	pinctrl-0 = <&spi3_pins>;
-	spi-nor@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		reg = <0>;
 		spi-max-frequency = <5000000>;
 		spi-rx-bus-width = <2>;
-		partitions@A0000000 {
+		partitions {
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -494,7 +494,7 @@
 
 &i2c1 {
 	status = "okay";
-	i2c-switch@75 {
+	i2c-mux@75 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -525,62 +525,62 @@
 			};
 		};
 
-		i2c-bus@4 {
+		i2c@4 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <4>;
 
 			// INLET1_T
-			lm75@5c {
-				compatible = "ti,lm75";
+			temperature-sensor@5c {
+				compatible = "national,lm75";
 				reg = <0x5c>;
 			};
 		};
 
-		i2c-bus@5 {
+		i2c@5 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <5>;
 
 			// OUTLET1_T
-			lm75@5c {
-				compatible = "ti,lm75";
+			temperature-sensor@5c {
+				compatible = "national,lm75";
 				reg = <0x5c>;
 			};
 		};
 
-		i2c-bus@6 {
+		i2c@6 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <6>;
 
 			// OUTLET2_T
-			lm75@5c {
-				compatible = "ti,lm75";
+			temperature-sensor@5c {
+				compatible = "national,lm75";
 				reg = <0x5c>;
 			};
 		};
 
-		i2c-bus@7 {
+		i2c@7 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <7>;
 
 			// OUTLET3_T
-			lm75@5c {
-				compatible = "ti,lm75";
+			temperature-sensor@5c {
+				compatible = "national,lm75";
 				reg = <0x5c>;
 			};
 		};
 	};
-	i2c-switch@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
 		reg = <0x77>;
 		i2c-mux-idle-disconnect;
 
-		i2c-bus@2 {
+		i2c@2 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <2>;
@@ -613,14 +613,14 @@
 
 &i2c4 {
 	status = "okay";
-	i2c-switch@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
 		reg = <0x77>;
 		i2c-mux-idle-disconnect;
 
-		i2c-bus@0 {
+		i2c@0 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0>;
@@ -632,7 +632,7 @@
 			};
 		};
 
-		i2c-bus@1 {
+		i2c@1 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <1>;
@@ -684,56 +684,56 @@
 
 &i2c13 {
 	status = "okay";
-	i2c-switch@77 {
+	i2c-mux@77 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
 		reg = <0x77>;
 		i2c-mux-idle-disconnect;
 
-		i2c-bus@3 {
+		i2c@3 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <3>;
 
 			// M2_ZONE_T
-			lm75@28 {
-				compatible = "ti,lm75";
+			temperature-sensor@28 {
+				compatible = "national,lm75";
 				reg = <0x28>;
 			};
 		};
 
-		i2c-bus@4 {
+		i2c@4 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <4>;
 
 			// BATT_ZONE_T
-			lm75@29 {
-				compatible = "ti,lm75";
+			temperature-sensor@29 {
+				compatible = "national,lm75";
 				reg = <0x29>;
 			};
 		};
 
-		i2c-bus@5 {
+		i2c@5 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <5>;
 
 			// NBM1_ZONE_T
-			lm75@28 {
-				compatible = "ti,lm75";
+			temperature-sensor@28 {
+				compatible = "national,lm75";
 				reg = <0x28>;
 			};
 		};
-		i2c-bus@6 {
+		i2c@6 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <6>;
 
 			// NBM2_ZONE_T
-			lm75@29 {
-				compatible = "ti,lm75";
+			temperature-sensor@29 {
+				compatible = "national,lm75";
 				reg = <0x29>;
 			};
 		};
diff --git a/arch/arm/boot/dts/nuvoton-npcm730.dtsi b/arch/arm/boot/dts/nuvoton/nuvoton-npcm730.dtsi
index 86ec12ec2b50..86ec12ec2b50 100644
--- a/arch/arm/boot/dts/nuvoton-npcm730.dtsi
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-npcm730.dtsi
diff --git a/arch/arm/boot/dts/nuvoton-npcm750-evb.dts b/arch/arm/boot/dts/nuvoton/nuvoton-npcm750-evb.dts
index 0334641f8829..bcdcb30c7bf6 100644
--- a/arch/arm/boot/dts/nuvoton-npcm750-evb.dts
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-npcm750-evb.dts
@@ -67,14 +67,14 @@
 
 &fiu0 {
 	status = "okay";
-	spi-nor@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		spi-rx-bus-width = <2>;
 		reg = <0>;
 		spi-max-frequency = <5000000>;
-		partitions@80000000 {
+		partitions {
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -128,14 +128,14 @@
 &fiu3 {
 	pinctrl-0 = <&spi3_pins>, <&spi3quad_pins>;
 	status = "okay";
-	spi-nor@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		spi-rx-bus-width = <2>;
 		reg = <0>;
 		spi-max-frequency = <5000000>;
-		partitions@A0000000 {
+		partitions {
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -198,7 +198,7 @@
 	clock-frequency = <100000>;
 	status = "okay";
 	lm75@48 {
-		compatible = "lm75";
+		compatible = "national,lm75";
 		reg = <0x48>;
 		status = "okay";
 	};
@@ -208,8 +208,8 @@
 &i2c1 {
 	clock-frequency = <100000>;
 	status = "okay";
-	lm75@48 {
-		compatible = "lm75";
+	temperature-sensor@48 {
+		compatible = "national,lm75";
 		reg = <0x48>;
 		status = "okay";
 	};
@@ -324,7 +324,7 @@
 &spi0 {
 	cs-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
 	status = "okay";
-	Flash@0 {
+	flash@0 {
 		compatible = "winbond,w25q128",
 		"jedec,spi-nor";
 		reg = <0x0>;
@@ -345,7 +345,7 @@
 &spi1 {
 	cs-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
 	status = "okay";
-	Flash@0 {
+	flash@0 {
 		compatible = "winbond,w25q128fw",
 		"jedec,spi-nor";
 		reg = <0x0>;
diff --git a/arch/arm/boot/dts/nuvoton-npcm750-pincfg-evb.dtsi b/arch/arm/boot/dts/nuvoton/nuvoton-npcm750-pincfg-evb.dtsi
index 3b3806274adf..3b3806274adf 100644
--- a/arch/arm/boot/dts/nuvoton-npcm750-pincfg-evb.dtsi
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-npcm750-pincfg-evb.dtsi
diff --git a/arch/arm/boot/dts/nuvoton-npcm750-runbmc-olympus-pincfg.dtsi b/arch/arm/boot/dts/nuvoton/nuvoton-npcm750-runbmc-olympus-pincfg.dtsi
index 230cb344b2e1..230cb344b2e1 100644
--- a/arch/arm/boot/dts/nuvoton-npcm750-runbmc-olympus-pincfg.dtsi
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-npcm750-runbmc-olympus-pincfg.dtsi
diff --git a/arch/arm/boot/dts/nuvoton-npcm750-runbmc-olympus.dts b/arch/arm/boot/dts/nuvoton/nuvoton-npcm750-runbmc-olympus.dts
index 767e0ac0df7c..0c94e14d40e8 100644
--- a/arch/arm/boot/dts/nuvoton-npcm750-runbmc-olympus.dts
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-npcm750-runbmc-olympus.dts
@@ -100,18 +100,18 @@
 	pinctrl-0 = <&spi0cs1_pins>;
 	status = "okay";
 
-	spi-nor@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		reg = <0>;
 		spi-rx-bus-width = <2>;
 
-		partitions@80000000 {
+		partitions {
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
 			#size-cells = <1>;
-			bmc@0{
+			bmc@0 {
 				label = "bmc";
 				reg = <0x000000 0x2000000>;
 			};
@@ -120,7 +120,7 @@
 				reg = <0x0000000 0x80000>;
 				read-only;
 			};
-			u-boot-env@100000{
+			u-boot-env@100000 {
 				label = "u-boot-env";
 				reg = <0x00100000 0x40000>;
 			};
@@ -139,14 +139,14 @@
 		};
 	};
 
-	spi-nor@1 {
+	flash@1 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		reg = <1>;
 		npcm,fiu-rx-bus-width = <2>;
 
-		partitions@88000000 {
+		partitions {
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -166,14 +166,14 @@
 	pinctrl-0 = <&spi3_pins>;
 	status = "okay";
 
-	spi-nor@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		reg = <0>;
 		spi-rx-bus-width = <2>;
 
-		partitions@A0000000 {
+		partitions {
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -208,81 +208,81 @@
 &i2c1 {
 	status = "okay";
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		#address-cells = <1>;
 		#size-cells = <0>;
 		reg = <0x70>;
 		i2c-mux-idle-disconnect;
 
-		i2c_slot1a: i2c-bus@0 {
+		i2c_slot1a: i2c@0 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0>;
 		};
 
-		i2c_slot1b: i2c-bus@1 {
+		i2c_slot1b: i2c@1 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <1>;
 		};
 
-		i2c_slot2a: i2c-bus@2 {
+		i2c_slot2a: i2c@2 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <2>;
 		};
 
-		i2c_slot2b: i2c-bus@3 {
+		i2c_slot2b: i2c@3 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <3>;
 		};
 
-		i2c_slot3: i2c-bus@4 {
+		i2c_slot3: i2c@4 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <4>;
 		};
 
-		i2c_slot4: i2c-bus@5 {
+		i2c_slot4: i2c@5 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <5>;
 		};
 
-		i2c_slot5: i2c-bus@6 {
+		i2c_slot5: i2c@6 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <6>;
 		};
 	};
 
-	i2c-switch@71 {
+	i2c-mux@71 {
 		compatible = "nxp,pca9546";
 		reg = <0x71>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 		i2c-mux-idle-disconnect;
 
-		i2c_m2_s1: i2c-bus@0 {
+		i2c_m2_s1: i2c@0 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0>;
 		};
 
-		i2c_m2_s2: i2c-bus@1 {
+		i2c_m2_s2: i2c@1 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <1>;
 		};
-		i2c_m2_s3: i2c-bus@2 {
+		i2c_m2_s3: i2c@2 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <2>;
 		};
 
-		i2c_m2_s4: i2c-bus@3 {
+		i2c_m2_s4: i2c@3 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <3>;
@@ -427,91 +427,91 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 		reset-gpios = <&gpio7 4 GPIO_ACTIVE_LOW>;
-		G1A_P0_0 {
+		g1a-p0-0-hog {
 			gpio-hog;
 			gpios = <0 0>;
 			output-high;
 			line-name = "TPM_BMC_ALERT_N";
 		};
-		G1A_P0_1 {
+		g1a-p0-1-hog {
 			gpio-hog;
 			gpios = <1 0>;
 			input;
 			line-name = "FM_BIOS_TOP_SWAP";
 		};
-		G1A_P0_2 {
+		g1a-p0-2-hog {
 			gpio-hog;
 			gpios = <2 0>;
 			input;
 			line-name = "FM_BIOS_PREFRB2_GOOD";
 		};
-		G1A_P0_3 {
+		g1a-p0-3-hog {
 			gpio-hog;
 			gpios = <3 0>;
 			input;
 			line-name = "BMC_SATAXPCIE_0TO3_SEL";
 		};
-		G1A_P0_4 {
+		g1a-p0-4-hog {
 			gpio-hog;
 			gpios = <4 0>;
 			input;
 			line-name = "BMC_SATAXPCIE_4TO7_SEL";
 		};
-		G1A_P0_5 {
+		g1a-p0-5-hog {
 			gpio-hog;
 			gpios = <5 0>;
 			output-low;
 			line-name = "FM_UV_ADR_TRIGGER_EN_N";
 		};
-		G1A_P0_6 {
+		g1a-p0-6-hog {
 			gpio-hog;
 			gpios = <6 0>;
 			input;
 			line-name = "RM_THROTTLE_EN_N";
 		};
-		G1A_P1_0 {
+		g1a-p1-0-hog {
 			gpio-hog;
 			gpios = <8 0>;
 			input;
 			line-name = "FM_BMC_TPM_PRES_N";
 		};
-		G1A_P1_1 {
+		g1a-p1-1-hog {
 			gpio-hog;
 			gpios = <9 0>;
 			input;
 			line-name = "FM_CPU0_SKTOCC_LVT3_N";
 		};
-		G1A_P1_2 {
+		g1a-p1-2-hog {
 			gpio-hog;
 			gpios = <10 0>;
 			input;
 			line-name = "FM_CPU1_SKTOCC_LVT3_N";
 		};
-		G1A_P1_3 {
+		g1a-p1-3-hog {
 			gpio-hog;
 			gpios = <11 0>;
 			input;
 			line-name = "PSU1_ALERT_N";
 		};
-		G1A_P1_4 {
+		g1a-p1-4-hog {
 			gpio-hog;
 			gpios = <12 0>;
 			input;
 			line-name = "PSU2_ALERT_N";
 		};
-		G1A_P1_5 {
+		g1a-p1-5-hog {
 			gpio-hog;
 			gpios = <13 0>;
 			input;
 			line-name = "H_CPU0_FAST_WAKE_LVT3_N";
 		};
-		G1A_P1_6 {
+		g1a-p1-6-hog {
 			gpio-hog;
 			gpios = <14 0>;
 			output-high;
 			line-name = "I2C_MUX1_RESET_N";
 		};
-		G1A_P1_7 {
+		g1a-p1-7-hog {
 			gpio-hog;
 			gpios = <15 0>;
 			input;
@@ -524,91 +524,91 @@
 		reg = <0x75>;
 		gpio-controller;
 		#gpio-cells = <2>;
-		G1B_P0_0 {
+		g1b-p0-0-hog {
 			gpio-hog;
 			gpios = <0 0>;
 			input;
 			line-name = "PVDDQ_ABC_PINALERT_N";
 		};
-		G1B_P0_1 {
+		g1b-p0-1-hog {
 			gpio-hog;
 			gpios = <1 0>;
 			input;
 			line-name = "PVDDQ_DEF_PINALERT_N";
 		};
-		G1B_P0_2 {
+		g1b-p0-2-hog {
 			gpio-hog;
 			gpios = <2 0>;
 			input;
 			line-name = "PVDDQ_GHJ_PINALERT_N";
 		};
-		G1B_P0_3 {
+		g1b-p0-3-hog {
 			gpio-hog;
 			gpios = <3 0>;
 			input;
 			line-name = "PVDDQ_KLM_PINALERT_N";
 		};
-		G1B_P0_5 {
+		g1b-p0-5-hog {
 			gpio-hog;
 			gpios = <5 0>;
 			input;
 			line-name = "FM_BOARD_REV_ID0";
 		};
-		G1B_P0_6 {
+		g1b-p0-6-hog {
 			gpio-hog;
 			gpios = <6 0>;
 			input;
 			line-name = "FM_BOARD_REV_ID1";
 		};
-		G1B_P0_7 {
+		g1b-p0-7-hog {
 			gpio-hog;
 			gpios = <7 0>;
 			input;
 			line-name = "FM_BOARD_REV_ID2";
 		};
-		G1B_P1_0 {
+		g1b-p1-0-hog {
 			gpio-hog;
 			gpios = <8 0>;
 			input;
 			line-name = "FM_OC_DETECT_EN_N";
 		};
-		G1B_P1_1 {
+		g1b-p1-1-hog {
 			gpio-hog;
 			gpios = <9 0>;
 			input;
 			line-name = "FM_FLASH_DESC_OVERRIDE";
 		};
-		G1B_P1_2 {
+		g1b-p1-2-hog {
 			gpio-hog;
 			gpios = <10 0>;
 			output-low;
 			line-name = "FP_PWR_ID_LED_N";
 		};
-		G1B_P1_3 {
+		g1b-p1-3-hog {
 			gpio-hog;
 			gpios = <11 0>;
 			output-low;
 			line-name = "BMC_LED_PWR_GRN";
 		};
-		G1B_P1_4 {
+		g1b-p1-4-hog {
 			gpio-hog;
 			gpios = <12 0>;
 			output-low;
 			line-name = "BMC_LED_PWR_AMBER";
 		};
-		G1B_P1_5 {
+		g1b-p1-5-hog {
 			gpio-hog;
 			gpios = <13 0>;
 			output-high;
 			line-name = "FM_BMC_FAULT_LED_N";
 		};
-		G1B_P1_6 {
+		g1b-p1-6-hog {
 			gpio-hog;
 			gpios = <14 0>;
 			output-high;
 			line-name = "FM_CPLD_BMC_PWRDN_N";
 		};
-		G1B_P1_7 {
+		g1b-p1-7-hog {
 			gpio-hog;
 			gpios = <15 0>;
 			output-high;
@@ -626,91 +626,91 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 		reset-gpios = <&gpio5 28 GPIO_ACTIVE_LOW>;
-		G2A_P0_0 {
+		g2a-p0-0-hog {
 			gpio-hog;
 			gpios = <0 0>;
 			output-high;
 			line-name = "BMC_PON_RST_REQ_N";
 		};
-		G2A_P0_1 {
+		g2a-p0-1-hog {
 			gpio-hog;
 			gpios = <1 0>;
 			output-high;
 			line-name = "BMC_RST_IND_REQ_N";
 		};
-		G2A_P0_2 {
+		g2a-p0-2-hog {
 			gpio-hog;
 			gpios = <2 0>;
 			input;
 			line-name = "RST_BMC_RTCRST";
 		};
-		G2A_P0_3 {
+		g2a-p0-3-hog {
 			gpio-hog;
 			gpios = <3 0>;
 			output-high;
 			line-name = "FM_BMC_PWRBTN_OUT_N";
 		};
-		G2A_P0_4 {
+		g2a-p0-4-hog {
 			gpio-hog;
 			gpios = <4 0>;
 			output-high;
 			line-name = "RST_BMC_SYSRST_BTN_OUT_N";
 		};
-		G2A_P0_5 {
+		g2a-p0-5-hog {
 			gpio-hog;
 			gpios = <5 0>;
 			output-high;
 			line-name = "FM_BATTERY_SENSE_EN_N";
 		};
-		G2A_P0_6 {
+		g2a-p0-6-hog {
 			gpio-hog;
 			gpios = <6 0>;
 			output-high;
 			line-name = "FM_BMC_READY_N";
 		};
-		G2A_P0_7 {
+		g2a-p0-7-hog {
 			gpio-hog;
 			gpios = <7 0>;
 			input;
 			line-name = "IRQ_BMC_PCH_SMI_LPC_N";
 		};
-		G2A_P1_0 {
+		g2a-p1-0-hog {
 			gpio-hog;
 			gpios = <8 0>;
 			input;
 			line-name = "FM_SLOT4_CFG0";
 		};
-		G2A_P1_1 {
+		g2a-p1-1-hog {
 			gpio-hog;
 			gpios = <9 0>;
 			input;
 			line-name = "FM_SLOT4_CFG1";
 		};
-		G2A_P1_2 {
+		g2a-p1-2-hog {
 			gpio-hog;
 			gpios = <10 0>;
 			input;
 			line-name = "FM_NVDIMM_EVENT_N";
 		};
-		G2A_P1_3 {
+		g2a-p1-3-hog {
 			gpio-hog;
 			gpios = <11 0>;
 			input;
 			line-name = "PSU1_BLADE_EN_N";
 		};
-		G2A_P1_4 {
+		g2a-p1-4-hog {
 			gpio-hog;
 			gpios = <12 0>;
 			input;
 			line-name = "BMC_PCH_FNM";
 		};
-		G2A_P1_5 {
+		g2a-p1-5-hog {
 			gpio-hog;
 			gpios = <13 0>;
 			input;
 			line-name = "FM_SOL_UART_CH_SEL";
 		};
-		G2A_P1_6 {
+		g2a-p1-6-hog {
 			gpio-hog;
 			gpios = <14 0>;
 			input;
@@ -723,91 +723,91 @@
 		reg = <0x75>;
 		gpio-controller;
 		#gpio-cells = <2>;
-		G2B_P0_0 {
+		g2b-p0-0-hog {
 			gpio-hog;
 			gpios = <0 0>;
 			input;
 			line-name = "FM_CPU_MSMI_LVT3_N";
 		};
-		G2B_P0_1 {
+		g2b-p0-1-hog {
 			gpio-hog;
 			gpios = <1 0>;
 			input;
 			line-name = "FM_BIOS_MRC_DEBUG_MSG_DIS";
 		};
-		G2B_P0_2 {
+		g2b-p0-2-hog {
 			gpio-hog;
 			gpios = <2 0>;
 			input;
 			line-name = "FM_CPU1_DISABLE_BMC_N";
 		};
-		G2B_P0_3 {
+		g2b-p0-3-hog {
 			gpio-hog;
 			gpios = <3 0>;
 			output-low;
 			line-name = "BMC_JTAG_SELECT";
 		};
-		G2B_P0_4 {
+		g2b-p0-4-hog {
 			gpio-hog;
 			gpios = <4 0>;
 			output-high;
 			line-name = "PECI_MUX_SELECT";
 		};
-		G2B_P0_5 {
+		g2b-p0-5-hog {
 			gpio-hog;
 			gpios = <5 0>;
 			output-high;
 			line-name = "I2C_MUX2_RESET_N";
 		};
-		G2B_P0_6 {
+		g2b-p0-6-hog {
 			gpio-hog;
 			gpios = <6 0>;
 			input;
 			line-name = "FM_BMC_CPLD_PSU2_ON";
 		};
-		G2B_P0_7 {
+		g2b-p0-7-hog {
 			gpio-hog;
 			gpios = <7 0>;
 			output-high;
 			line-name = "PSU2_ALERT_EN_N";
 		};
-		G2B_P1_0 {
+		g2b-p1-0-hog {
 			gpio-hog;
 			gpios = <8 0>;
 			output-high;
 			line-name = "FM_CPU_BMC_INIT";
 		};
-		G2B_P1_1 {
+		g2b-p1-1-hog {
 			gpio-hog;
 			gpios = <9 0>;
 			output-high;
 			line-name = "IRQ_BMC_PCH_SCI_LPC_N";
 		};
-		G2B_P1_2 {
+		g2b-p1-2-hog {
 			gpio-hog;
 			gpios = <10 0>;
 			output-low;
 			line-name = "PMB_ALERT_EN_N";
 		};
-		G2B_P1_3 {
+		g2b-p1-3-hog {
 			gpio-hog;
 			gpios = <11 0>;
 			output-high;
 			line-name = "FM_FAST_PROCHOT_EN_N";
 		};
-		G2B_P1_4 {
+		g2b-p1-4-hog {
 			gpio-hog;
 			gpios = <12 0>;
 			output-high;
 			line-name = "BMC_NVDIMM_PRSNT_N";
 		};
-		G2B_P1_5 {
+		g2b-p1-5-hog {
 			gpio-hog;
 			gpios = <13 0>;
 			output-low;
 			line-name = "FM_BACKUP_BIOS_SEL_H_BMC";
 		};
-		G2B_P1_6 {
+		g2b-p1-6-hog {
 			gpio-hog;
 			gpios = <14 0>;
 			output-high;
@@ -824,7 +824,7 @@
 		reg = <0x4a>;
 		status = "okay";
 	};
-	m24128_fru@51 {
+	eeprom@51 {
 		compatible = "atmel,24c128";
 		reg = <0x51>;
 		pagesize = <64>;
diff --git a/arch/arm/boot/dts/nuvoton/nuvoton-npcm750.dtsi b/arch/arm/boot/dts/nuvoton/nuvoton-npcm750.dtsi
new file mode 100644
index 000000000000..65fe3a180bb1
--- /dev/null
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-npcm750.dtsi
@@ -0,0 +1,127 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2018 Nuvoton Technology tomer.maimon@nuvoton.com
+// Copyright 2018 Google, Inc.
+
+#include "nuvoton-common-npcm7xx.dtsi"
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		enable-method = "nuvoton,npcm750-smp";
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			clocks = <&clk NPCM7XX_CLK_CPU>;
+			clock-names = "clk_cpu";
+			reg = <0>;
+			next-level-cache = <&l2>;
+		};
+
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			clocks = <&clk NPCM7XX_CLK_CPU>;
+			clock-names = "clk_cpu";
+			reg = <1>;
+			next-level-cache = <&l2>;
+		};
+	};
+
+	soc {
+		timer@3fe600 {
+			compatible = "arm,cortex-a9-twd-timer";
+			reg = <0x3fe600 0x20>;
+			interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) |
+						  IRQ_TYPE_LEVEL_HIGH)>;
+			clocks = <&clk NPCM7XX_CLK_AHB>;
+		};
+	};
+
+	ahb {
+		gmac1: ethernet@f0804000 {
+			device_type = "network";
+			compatible = "snps,dwmac";
+			reg = <0xf0804000 0x2000>;
+			interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			ethernet = <1>;
+			clocks = <&clk_rg2refck>, <&clk NPCM7XX_CLK_AHB>;
+			clock-names = "stmmaceth", "clk_gmac";
+			pinctrl-names = "default";
+			pinctrl-0 = <&rg2_pins
+					&rg2mdio_pins>;
+			status = "disabled";
+		};
+
+		udc0: usb@f0830000 {
+			compatible = "nuvoton,npcm750-udc";
+			reg = <0xf0830000 0x1000
+			       0xfffd0000 0x800>;
+			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM7XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc1: usb@f0831000 {
+			compatible = "nuvoton,npcm750-udc";
+			reg = <0xf0831000 0x1000
+			       0xfffd0800 0x800>;
+			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM7XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc2: usb@f0832000 {
+			compatible = "nuvoton,npcm750-udc";
+			reg = <0xf0832000 0x1000
+			       0xfffd1000 0x800>;
+			interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM7XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc3: usb@f0833000 {
+			compatible = "nuvoton,npcm750-udc";
+			reg = <0xf0833000 0x1000
+			       0xfffd1800 0x800>;
+			interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM7XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc4: usb@f0834000 {
+			compatible = "nuvoton,npcm750-udc";
+			reg = <0xf0834000 0x1000
+			       0xfffd2000 0x800>;
+			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM7XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/nuvoton-wpcm450-supermicro-x9sci-ln4f.dts b/arch/arm/boot/dts/nuvoton/nuvoton-wpcm450-supermicro-x9sci-ln4f.dts
index 3ee61251a16d..edb907f740bf 100644
--- a/arch/arm/boot/dts/nuvoton-wpcm450-supermicro-x9sci-ln4f.dts
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-wpcm450-supermicro-x9sci-ln4f.dts
@@ -15,6 +15,11 @@
 	model = "Supermicro X9SCi-LN4F BMC";
 	compatible = "supermicro,x9sci-ln4f-bmc", "nuvoton,wpcm450";
 
+	aliases {
+		serial0 = &serial0;
+		serial1 = &serial1;
+	};
+
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
@@ -29,7 +34,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&key_pins>;
 
-		uid {
+		button-uid {
 			label = "UID button";
 			linux,code = <KEY_HOME>;
 			gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
@@ -41,18 +46,45 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins>;
 
-		uid {
+		led-uid {
 			label = "UID";
 			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
 		};
 
-		heartbeat {
+		led-heartbeat {
 			label = "heartbeat";
 			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
 		};
 	};
 };
 
+&fiu {
+	status = "okay";
+
+	flash@0 {
+		reg = <0>;
+		compatible = "jedec,spi-nor";
+	};
+};
+
+&gpio0 {
+	gpio-line-names =
+		/* 0 */ "", "host-reset-control-n", "", "", "", "", "", "",
+		/* 8 */ "", "", "", "", "power-chassis-control-n", "", "uid-button", "";
+};
+
+&gpio1 {
+	gpio-line-names =
+		/* 0 */ "", "", "", "", "led-heartbeat", "", "", "led-uid",
+		/* 8 */ "", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names =
+		/* 0 */ "", "", "", "", "", "", "", "",
+		/* 8 */ "", "", "", "", "", "", "", "power-chassis-good";
+};
+
 &pinctrl {
 	key_pins: mux-keys {
 		groups = "gspi", "sspi";
@@ -77,7 +109,3 @@
 	/* "Serial over LAN" port. Connected to ttyS2 of the host system. */
 	status = "okay";
 };
-
-&watchdog0 {
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/nuvoton-wpcm450.dtsi b/arch/arm/boot/dts/nuvoton/nuvoton-wpcm450.dtsi
index 93595850a4c3..6e1f0f164cb4 100644
--- a/arch/arm/boot/dts/nuvoton-wpcm450.dtsi
+++ b/arch/arm/boot/dts/nuvoton/nuvoton-wpcm450.dtsi
@@ -37,6 +37,14 @@
 		#clock-cells = <0>;
 	};
 
+	refclk: clock-48mhz {
+		/* 48 MHz reference oscillator */
+		compatible = "fixed-clock";
+		clock-output-names = "ref";
+		clock-frequency = <48000000>;
+		#clock-cells = <0>;
+	};
+
 	soc {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -49,6 +57,15 @@
 			reg = <0xb0000000 0x200>;
 		};
 
+		clk: clock-controller@b0000200 {
+			compatible = "nuvoton,wpcm450-clk";
+			reg = <0xb0000200 0x100>;
+			clocks = <&refclk>;
+			clock-names = "ref";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
 		serial0: serial@b8000000 {
 			compatible = "nuvoton,wpcm450-uart";
 			reg = <0xb8000000 0x20>;
@@ -81,7 +98,6 @@
 			interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
 			reg = <0xb800101c 0x4>;
 			clocks = <&clk24m>;
-			status = "disabled";
 		};
 
 		aic: interrupt-controller@b8002000 {
@@ -104,6 +120,7 @@
 				interrupts = <2 IRQ_TYPE_LEVEL_HIGH>,
 					     <3 IRQ_TYPE_LEVEL_HIGH>,
 					     <4 IRQ_TYPE_LEVEL_HIGH>;
+				#interrupt-cells = <2>;
 				interrupt-controller;
 			};
 
@@ -112,6 +129,7 @@
 				gpio-controller;
 				#gpio-cells = <2>;
 				interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+				#interrupt-cells = <2>;
 				interrupt-controller;
 			};
 
@@ -456,5 +474,22 @@
 				function = "hg7";
 			};
 		};
+
+		fiu: spi-controller@c8000000 {
+			compatible = "nuvoton,wpcm450-fiu";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0xc8000000 0x1000>, <0xc0000000 0x4000000>;
+			reg-names = "control", "memory";
+			clocks = <&clk 0>;
+			nuvoton,shm = <&shm>;
+			status = "disabled";
+		};
+
+		shm: syscon@c8001000 {
+			compatible = "nuvoton,wpcm450-shm", "syscon";
+			reg = <0xc8001000 0x1000>;
+			reg-io-width = <1>;
+		};
 	};
 };
diff --git a/arch/arm/boot/dts/nvidia/Makefile b/arch/arm/boot/dts/nvidia/Makefile
new file mode 100644
index 000000000000..2ed2d923c8f9
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/Makefile
@@ -0,0 +1,49 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_TEGRA_114_SOC) += \
+	tegra114-asus-tf701t.dtb \
+	tegra114-dalmore.dtb \
+	tegra114-roth.dtb \
+	tegra114-tn7.dtb
+dtb-$(CONFIG_ARCH_TEGRA_124_SOC) += \
+	tegra124-apalis-eval.dtb \
+	tegra124-apalis-v1.2-eval.dtb \
+	tegra124-jetson-tk1.dtb \
+	tegra124-nyan-big.dtb \
+	tegra124-nyan-big-fhd.dtb \
+	tegra124-nyan-blaze.dtb \
+	tegra124-venice2.dtb
+dtb-$(CONFIG_ARCH_TEGRA_2x_SOC) += \
+	tegra20-acer-a500-picasso.dtb \
+	tegra20-asus-sl101.dtb \
+	tegra20-asus-tf101.dtb \
+	tegra20-harmony.dtb \
+	tegra20-colibri-eval-v3.dtb \
+	tegra20-colibri-iris.dtb \
+	tegra20-medcom-wide.dtb \
+	tegra20-paz00.dtb \
+	tegra20-plutux.dtb \
+	tegra20-seaboard.dtb \
+	tegra20-tec.dtb \
+	tegra20-trimslice.dtb \
+	tegra20-ventana.dtb
+dtb-$(CONFIG_ARCH_TEGRA_3x_SOC) += \
+	tegra30-apalis-eval.dtb \
+	tegra30-apalis-v1.1-eval.dtb \
+	tegra30-asus-nexus7-grouper-PM269.dtb \
+	tegra30-asus-nexus7-grouper-E1565.dtb \
+	tegra30-asus-nexus7-tilapia-E1565.dtb \
+	tegra30-asus-p1801-t.dtb \
+	tegra30-asus-tf201.dtb \
+	tegra30-asus-tf300t.dtb \
+	tegra30-asus-tf300tg.dtb \
+	tegra30-asus-tf300tl.dtb \
+	tegra30-asus-tf600t.dtb \
+	tegra30-asus-tf700t.dtb \
+	tegra30-beaver.dtb \
+	tegra30-cardhu-a02.dtb \
+	tegra30-cardhu-a04.dtb \
+	tegra30-colibri-eval-v3.dtb \
+	tegra30-lg-p880.dtb \
+	tegra30-lg-p895.dtb \
+	tegra30-ouya.dtb \
+	tegra30-pegatron-chagall.dtb
diff --git a/arch/arm/boot/dts/nvidia/tegra114-asus-tf701t.dts b/arch/arm/boot/dts/nvidia/tegra114-asus-tf701t.dts
new file mode 100644
index 000000000000..f02e2cf65fe8
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra114-asus-tf701t.dts
@@ -0,0 +1,1963 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+
+#include "tegra114.dtsi"
+
+/ {
+	model = "Asus Transformer Pad TF701T";
+	compatible = "asus,tf701t", "nvidia,tegra114";
+	chassis-type = "convertible";
+
+	aliases {
+		mmc0 = "/mmc@78000600"; /* eMMC */
+		mmc1 = "/mmc@78000400"; /* uSD slot */
+		mmc2 = "/mmc@78000000"; /* WiFi */
+
+		rtc0 = &palmas;
+		rtc1 = "/rtc@7000e000";
+
+		serial0 = &uartd; /* Console */
+		serial1 = &uartc; /* Bluetooth */
+		serial2 = &uartb; /* GPS */
+	};
+
+	firmware {
+		trusted-foundations {
+			compatible = "tlm,trusted-foundations";
+			tlm,version-major = <2>;
+			tlm,version-minor = <8>;
+		};
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		linux,cma@80000000 {
+			compatible = "shared-dma-pool";
+			alloc-ranges = <0x80000000 0x30000000>;
+			size = <0x10000000>;
+			linux,cma-default;
+			reusable;
+		};
+
+		trustzone@bfe00000 {
+			reg = <0xbfe00000 0x200000>;
+			no-map;
+		};
+	};
+
+	host1x@50000000 {
+		hdmi@54280000 {
+			status = "okay";
+
+			hdmi-supply = <&hdmi_5v0_sys>;
+			pll-supply = <&avdd_hdmi_pll>;
+			vdd-supply = <&avdd_hdmi>;
+
+			port {
+				hdmi_out: endpoint {
+					remote-endpoint = <&connector_in>;
+				};
+			};
+		};
+
+		dsi@54300000 {
+			status = "okay";
+
+			avdd-dsi-csi-supply = <&avdd_dsi_csi>;
+
+			nvidia,ganged-mode = <&dsib>;
+
+			panel_primary: panel@0 {
+				compatible = "sharp,lq101r1sx01";
+				reg = <0>;
+
+				link2 = <&panel_secondary>;
+
+				power-supply = <&dvdd_1v8_lcd>;
+				backlight = <&backlight>;
+			};
+		};
+
+		dsi@54400000 {
+			status = "okay";
+
+			avdd-dsi-csi-supply = <&avdd_dsi_csi>;
+
+			panel_secondary: panel@0 {
+				compatible = "sharp,lq101r1sx01";
+				reg = <0>;
+			};
+		};
+	};
+
+	vde@6001a000 {
+		assigned-clocks = <&tegra_car TEGRA114_CLK_VDE>;
+		assigned-clock-parents = <&tegra_car TEGRA114_CLK_PLL_P>;
+		assigned-clock-rates = <408000000>;
+	};
+
+	pinmux@70000868 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&state_default>;
+
+		state_default: pinmux {
+			/* WLAN SDIO pinmux */
+			sdmmc1-clk {
+				nvidia,pins = "sdmmc1_clk_pz0";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc1-cmd {
+				nvidia,pins = "sdmmc1_cmd_pz1",
+					      "sdmmc1_dat0_py7",
+					      "sdmmc1_dat1_py6",
+					      "sdmmc1_dat2_py5",
+					      "sdmmc1_dat3_py4";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			wlan-power {
+				nvidia,pins = "clk2_req_pcc5";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			wlan-reset {
+				nvidia,pins = "gpio_x7_aud_px7";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			wlan-host-wake {
+				nvidia,pins = "pu5";
+				nvidia,function = "pwm2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			wlan-3v3-com {
+				nvidia,pins = "pu1";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* UART-A pinmux */
+			uarta-cts {
+				nvidia,pins = "kb_row10_ps2";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			uarta-rts {
+				nvidia,pins = "kb_row9_ps1";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* GNSS UART-B pinmux */
+			uartb-cts {
+				nvidia,pins = "uart2_cts_n_pj5";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			uartb-rts {
+				nvidia,pins = "uart2_rts_n_pj6";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			uartb-rxd {
+				nvidia,pins = "uart2_rxd_pc3";
+				nvidia,function = "irda";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			uartb-txd {
+				nvidia,pins = "uart2_txd_pc2";
+				nvidia,function = "irda";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* Bluetooth UART-C pinmux */
+			uartc-cts-rxd {
+				nvidia,pins = "uart3_cts_n_pa1",
+					      "uart3_rxd_pw7";
+				nvidia,function = "uartc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			uartc-rts-txd {
+				nvidia,pins = "uart3_rts_n_pc0",
+					      "uart3_txd_pw6";
+				nvidia,function = "uartc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			bt-shutdown {
+				nvidia,pins = "kb_col6_pq6",
+					      "kb_col7_pq7";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			bt-dev-wake {
+				nvidia,pins = "clk3_req_pee1";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			bt-host-wake {
+				nvidia,pins = "pu6";
+				nvidia,function = "pwm3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			bt-pcm-dap4-out {
+				nvidia,pins = "dap4_fs_pp4",
+					      "dap4_dout_pp6",
+					      "dap4_sclk_pp7";
+				nvidia,function = "i2s3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			bt-pcm-dap4-in {
+				nvidia,pins = "dap4_din_pp5";
+				nvidia,function = "i2s3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* UART-D pinmux */
+			uartd-cts {
+				nvidia,pins = "gmi_a17_pb0";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			uartd-rts {
+				nvidia,pins = "gmi_a16_pj7",
+					      "gmi_a19_pk7";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* MicroSD pinmux */
+			sdmmc3-clk {
+				nvidia,pins = "sdmmc3_clk_pa6";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc3-data {
+				nvidia,pins = "sdmmc3_cmd_pa7",
+					      "sdmmc3_dat0_pb7",
+					      "sdmmc3_dat1_pb6",
+					      "sdmmc3_dat2_pb5",
+					      "sdmmc3_dat3_pb4",
+					      "kb_col4_pq4",
+					      "sdmmc3_cd_n_pv2",
+					      "sdmmc3_clk_lb_out_pee4",
+					      "sdmmc3_clk_lb_in_pee5";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			microsd-pwr {
+				nvidia,pins = "gmi_clk_pk1";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* EMMC pinmux */
+			sdmmc4-clk-cmd {
+				nvidia,pins = "sdmmc4_clk_pcc4";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc4-data {
+				nvidia,pins = "sdmmc4_cmd_pt7",
+					      "sdmmc4_dat0_paa0",
+					      "sdmmc4_dat1_paa1",
+					      "sdmmc4_dat2_paa2",
+					      "sdmmc4_dat3_paa3",
+					      "sdmmc4_dat4_paa4",
+					      "sdmmc4_dat5_paa5",
+					      "sdmmc4_dat6_paa6",
+					      "sdmmc4_dat7_paa7";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* I2C pinmux */
+			gen1-i2c {
+				nvidia,pins = "gen1_i2c_scl_pc4",
+					      "gen1_i2c_sda_pc5";
+				nvidia,function = "i2c1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <TEGRA_PIN_DISABLE>;
+			};
+
+			gen2-i2c {
+				nvidia,pins = "gen2_i2c_scl_pt5",
+					      "gen2_i2c_sda_pt6";
+				nvidia,function = "i2c2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <TEGRA_PIN_DISABLE>;
+			};
+
+			cam-i2c {
+				nvidia,pins = "cam_i2c_scl_pbb1",
+					      "cam_i2c_sda_pbb2";
+				nvidia,function = "i2c3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <TEGRA_PIN_DISABLE>;
+			};
+			
+			ddc-i2c {
+				nvidia,pins = "ddc_scl_pv4",
+					      "ddc_sda_pv5";
+				nvidia,function = "i2c4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <TEGRA_PIN_DISABLE>;
+			};
+
+			pwr-i2c {
+				nvidia,pins = "pwr_i2c_scl_pz6",
+					      "pwr_i2c_sda_pz7";
+				nvidia,function = "i2cpwr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* SPI pinmux */
+			spi1-out {
+				nvidia,pins = "ulpi_clk_py0",
+					      "ulpi_nxt_py2",
+					      "ulpi_stp_py3";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spi1-in {
+				nvidia,pins = "ulpi_dir_py1";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			spi2 {
+				nvidia,pins = "ulpi_data4_po5",
+					      "ulpi_data7_po0";
+				nvidia,function = "spi2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			spi4-out {
+				nvidia,pins = "gmi_ad6_pg6",
+					      "gmi_wr_n_pi0";
+				nvidia,function = "spi4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spi4-in {
+				nvidia,pins = "gmi_ad5_pg5",
+					      "gmi_ad7_pg7";
+				nvidia,function = "spi4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* GPIO keys pinmux */
+			hall-switch {
+				nvidia,pins = "ulpi_data4_po5";
+				nvidia,function = "spi2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			lineout-switch {
+				nvidia,pins = "gpio_x5_aud_px5";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			power-key {
+				nvidia,pins = "kb_col0_pq0";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			volume-keys {
+				nvidia,pins = "kb_row1_pr1",
+					      "kb_row2_pr2";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Sensors pinmux */
+			nct-irq {
+				nvidia,pins = "ulpi_data3_po4";
+				nvidia,function = "ulpi";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			mpu-irq {
+				nvidia,pins = "kb_row3_pr3";
+				nvidia,function = "rsvd3";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* HDMI pinmux */
+			hdmi-hpd {
+				nvidia,pins = "hdmi_int_pn7";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			hdmi-en {
+				nvidia,pins = "dap3_dout_pp2";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			hdmi-cec {
+				nvidia,pins = "hdmi_cec_pee3";
+				nvidia,function = "cec";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* LED pinmux */
+			backlight-pwm {
+				nvidia,pins = "gmi_ad9_ph1";
+				nvidia,function = "pwm1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			backlight-en {
+				nvidia,pins = "gmi_ad10_ph2";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* Touchscreen pinmux */
+			touch-irq {
+				nvidia,pins = "gmi_cs4_n_pk2";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			touch-rst {
+				nvidia,pins = "gmi_cs3_n_pk4";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			touch-pwr {
+				nvidia,pins = "gmi_ad8_ph0";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			touch-vio {
+				nvidia,pins = "gmi_ad12_ph4";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* AUDIO pinmux */
+			audio-ldo1 {
+				nvidia,pins = "sdmmc1_wp_n_pv3";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			hp-detect {
+				nvidia,pins = "kb_row7_pr7";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap-i2s0-in {
+				nvidia,pins = "dap1_din_pn1";
+				nvidia,function = "i2s0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap-i2s0-out {
+				nvidia,pins = "dap1_dout_pn2",
+					      "dap1_fs_pn0",
+					      "dap1_sclk_pn3";
+				nvidia,function = "i2s0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			dap-i2s1-in {
+				nvidia,pins = "dap2_din_pa4";
+				nvidia,function = "i2s1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap-i2s1-out {
+				nvidia,pins = "dap2_dout_pa5",
+					      "dap2_fs_pa2",
+					      "dap2_sclk_pa3";
+				nvidia,function = "i2s1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			dap-i2s2-in {
+				nvidia,pins = "dap3_fs_pp0",
+					      "dap3_sclk_pp3";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap-i2s2-out {
+				nvidia,pins = "dap3_din_pp1";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spdif-in {
+				nvidia,pins = "spdif_in_pk6";
+				nvidia,function = "rsvd3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spdif-out {
+				nvidia,pins = "spdif_out_pk5";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* AsusEC pinmux */
+			ec-irq {
+				nvidia,pins = "kb_col5_pq5";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ec-req {
+				nvidia,pins = "kb_col2_pq2";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			hotplug-i2c {
+				nvidia,pins = "ulpi_data7_po0";
+				nvidia,function = "spi2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ps2-irq {
+				nvidia,pins = "gpio_w2_aud_pw2";
+				nvidia,function = "spi6";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			kbd-irq {
+				nvidia,pins = "gmi_cs0_n_pj0";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dvfs-pin {
+				nvidia,pins = "dvfs_pwm_px0",
+					      "dvfs_clk_px2";
+				nvidia,function = "cldvfs";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* Core pinmux */
+			clk-32k-out {
+				nvidia,pins = "clk_32k_out_pa0";
+				nvidia,function = "soc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sys-clk-req {
+				nvidia,pins = "sys_clk_req_pz5";
+				nvidia,function = "sysclk";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			core-pwr-req {
+				nvidia,pins = "core_pwr_req";
+				nvidia,function = "pwron";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			cpu-pwr-req {
+				nvidia,pins = "cpu_pwr_req";
+				nvidia,function = "cpu";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pwr-int-n {
+				nvidia,pins = "pwr_int_n";
+				nvidia,function = "pmi";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			clk-32k-in {
+				nvidia,pins = "clk_32k_in";
+				nvidia,function = "clk";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			owr {
+				nvidia,pins = "owr";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			reset-out-n {
+				nvidia,pins = "reset_out_n";
+				nvidia,function = "reset_out_n";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* ULPI pinmux */
+			ulpi-data0-6 {
+				nvidia,pins = "ulpi_data0_po1",
+					      "ulpi_data6_po7";
+				nvidia,function = "ulpi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ulpi-data1-5 {
+				nvidia,pins = "ulpi_data1_po2",
+					      "ulpi_data5_po6";
+				nvidia,function = "ulpi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ulpi-data2-3 {
+				nvidia,pins = "ulpi_data2_po3",
+					      "ulpi_data3_po4";
+				nvidia,function = "ulpi";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* PORT V */
+			pv0-gpio {
+				nvidia,pins = "pv0";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pv1-gpio {
+				nvidia,pins = "pv1";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* PORT U */
+			pu0-gpio {
+				nvidia,pins = "pu0";
+				nvidia,function = "rsvd3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pu2-gpio {
+				nvidia,pins = "pu2";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* PWM pinmux */
+			pwm0 {
+				nvidia,pins = "pu3";
+				nvidia,function = "pwm0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pwm1 {
+				nvidia,pins = "pu4";
+				nvidia,function = "pwm1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* EXTPERIPH pinmux */
+			clk1-out {
+				nvidia,pins = "clk1_out_pw4";
+				nvidia,function = "extperiph1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			clk2-out {
+				nvidia,pins = "clk2_out_pw5";
+				nvidia,function = "extperiph2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			clk3-out {
+				nvidia,pins = "clk3_out_pee0";
+				nvidia,function = "extperiph3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			clk1-req {
+				nvidia,pins = "clk1_req_pee2";
+				nvidia,function = "rsvd3";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* GMI pinmux */
+			gmi-wp-n {
+				nvidia,pins = "gmi_wp_n_pc7";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi-adv {
+				nvidia,pins = "gmi_adv_n_pk0";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi-ad0-ad1 {
+				nvidia,pins = "gmi_ad0_pg0",
+					      "gmi_ad1_pg1";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi-ad2-ad3 {
+				nvidia,pins = "gmi_ad2_pg2",
+					      "gmi_ad3_pg3";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi-iordy {
+				nvidia,pins = "gmi_iordy_pi5";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi-a18 {
+				nvidia,pins = "gmi_a18_pb1";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi-wait {
+				nvidia,pins = "gmi_wait_pi7";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi-cs6-n {
+				nvidia,pins = "gmi_cs6_n_pi3";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi-cs7-n {
+				nvidia,pins = "gmi_cs7_n_pi6";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi-dqs-p {
+				nvidia,pins = "gmi_dqs_p_pj3";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi-cs2-ad {
+				nvidia,pins = "gmi_cs2_n_pk3",
+					      "gmi_ad14_ph6",
+					      "gmi_ad15_ph7";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi-cs4-clk {
+				nvidia,pins = "gmi_cs4_n_pk2",
+					      "gmi_clk_lb";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi-ad11 {
+				nvidia,pins = "gmi_ad11_ph3";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi-cs1-oe {
+				nvidia,pins = "gmi_cs1_n_pj2",
+					      "gmi_oe_n_pi1";
+				nvidia,function = "soc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi-ad4 {
+				nvidia,pins = "gmi_ad4_pg4";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi-ad13 {
+				nvidia,pins = "gmi_ad13_ph5";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi-rst-n {
+				nvidia,pins = "gmi_rst_n_pi4";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* PORT CC */
+			pcc-gpio {
+				nvidia,pins = "pcc1", "pcc2";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* PORT BB */
+			pbb3-gpio {
+				nvidia,pins = "pbb3";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pbb4-5-6-gpio {
+				nvidia,pins = "pbb4", "pbb5", "pbb6";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pbb7-gpio {
+				nvidia,pins = "pbb7";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* KBC pinmux */
+			kb-r0-c1 {
+				nvidia,pins = "kb_row0_pr0",
+					      "kb_col1_pq1";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			kb-row4 {
+				nvidia,pins = "kb_row4_pr4";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			kb-row5 {
+				nvidia,pins = "kb_row5_pr5";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			kb-row6 {
+				nvidia,pins = "kb_row6_pr6";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			kb-r8-c3 {
+				nvidia,pins = "kb_row8_ps0",
+					      "kb_col3_pq3";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* VI pinmux */
+			cam-mclk {
+				nvidia,pins = "cam_mclk_pcc0",
+					      "pbb0";
+				nvidia,function = "vi_alt3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* AUD pinmux */
+			gpio-x4-aud {
+				nvidia,pins = "gpio_x4_aud_px4";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gpio-x1-aud {
+				nvidia,pins = "gpio_x1_aud_px1";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gpio-x3-aud {
+				nvidia,pins = "gpio_x3_aud_px3";
+				nvidia,function = "rsvd3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gpio-x6-aud {
+				nvidia,pins = "gpio_x6_aud_px6";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			usb-vbus {
+				nvidia,pins = "usb_vbus_en0_pn4",
+					      "usb_vbus_en1_pn5";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* GPIO power/drive control */
+			drive-sdio1 {
+				nvidia,pins = "drive_sdio1";
+				nvidia,high-speed-mode = <TEGRA_PIN_ENABLE>;
+				nvidia,schmitt = <TEGRA_PIN_DISABLE>;
+				nvidia,pull-down-strength = <36>;
+				nvidia,pull-up-strength = <20>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_SLOW>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_SLOW>;
+			};
+
+			drive-sdio3 {
+				nvidia,pins = "drive_sdio3";
+				nvidia,high-speed-mode = <TEGRA_PIN_ENABLE>;
+				nvidia,schmitt = <TEGRA_PIN_DISABLE>;
+				nvidia,pull-down-strength = <22>;
+				nvidia,pull-up-strength = <36>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+			};
+
+			drive-gma {
+				nvidia,pins = "drive_gma";
+				nvidia,high-speed-mode = <TEGRA_PIN_ENABLE>;
+				nvidia,schmitt = <TEGRA_PIN_DISABLE>;
+				nvidia,pull-down-strength = <2>;
+				nvidia,pull-up-strength = <2>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+			};
+		};
+	};
+
+	serial@70006040 {
+		/* GPS */
+	};
+
+	serial@70006200 {
+		compatible = "nvidia,tegra114-hsuart", "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
+		status = "okay";
+
+		nvidia,adjust-baud-rates = <0 9600 100>,
+					   <9600 115200 200>,
+					   <1000000 4000000 136>;
+
+		bluetooth {
+			compatible = "brcm,bcm4334-bt";
+			max-speed = <4000000>;
+
+			clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
+			clock-names = "txco";
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(U, 6) IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "host-wakeup";
+
+			device-wakeup-gpios = <&gpio TEGRA_GPIO(EE, 1) GPIO_ACTIVE_HIGH>;
+			shutdown-gpios = <&gpio TEGRA_GPIO(Q, 7) GPIO_ACTIVE_HIGH>;
+			reset-gpios = <&gpio TEGRA_GPIO(Q, 6) GPIO_ACTIVE_LOW>;
+
+			vbat-supply = <&vdd_3v3_com>;
+			vddio-supply = <&vdd_1v8_vio>;
+		};
+	};
+
+	serial@70006300 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
+		status = "okay";
+	};
+
+	pwm@7000a000 {
+		status = "okay";
+	};
+
+	i2c@7000c000 {
+		status = "okay";
+		clock-frequency = <100000>;
+
+		magnetometer@c {
+			compatible = "asahi-kasei,ak09911";
+			reg = <0xc>;
+
+			/* no DRDY (polling) */
+
+			vdd-supply = <&vdd_2v85_sen>;
+			vid-supply = <&vdd_1v8_vio>;
+
+			mount-matrix =  "0",  "1", "0",
+					"1",  "0", "0",
+					"0",  "0","-1";
+		};
+
+		rt5639: audio-codec@1c {
+			compatible = "realtek,rt5639";
+			reg = <0x1c>;
+
+			realtek,ldo1-en-gpios =
+				<&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
+
+			clocks = <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+			clock-names = "mclk";
+		};
+
+		temp_sensor: temperature-sensor@4c {
+			compatible = "onnn,nct1008";
+			reg = <0x4c>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(O, 4) IRQ_TYPE_EDGE_FALLING>;
+
+			vcc-supply = <&vdd_1v8_vio>;
+			#thermal-sensor-cells = <1>;
+		};
+
+		motion-tracker@68 {
+			compatible = "invensense,mpu6500";
+			reg = <0x68>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(R, 3) IRQ_TYPE_LEVEL_HIGH>;
+
+			vdd-supply = <&vdd_2v85_sen>;
+			vddio-supply = <&vdd_1v8_vio>;
+
+			mount-matrix =  "0", "-1", "0",
+					"1",  "0", "0",
+					"0",  "0", "1";
+		};
+	};
+
+	i2c@7000c400 {
+		status = "okay";
+		clock-frequency = <100000>;
+
+		power-sensor@44 {
+			compatible = "ti,ina230";
+			reg = <0x44>;
+
+			shunt-resistor = <5000>;
+		};
+	};
+
+	i2c@7000c500 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		light-sensor@1c {
+			compatible = "dynaimage,al3320a";
+			reg = <0x1c>;
+
+			vdd-supply = <&vdd_1v8_vio>;
+		};
+	};
+
+	hdmi_ddc: i2c@7000c700 {
+		status = "okay";
+		clock-frequency = <10000>;
+	};
+
+	i2c@7000d000 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		palmas: pmic@58 {
+			compatible = "ti,tps65913", "ti,palmas";
+			reg = <0x58>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+
+			#interrupt-cells = <2>;
+			interrupt-controller;
+
+			ti,system-power-controller;
+
+			palmas_gpadc: adc {
+				compatible = "ti,palmas-gpadc";
+				interrupts = <18 IRQ_TYPE_NONE>,
+					     <16 IRQ_TYPE_NONE>,
+					     <17 IRQ_TYPE_NONE>;
+
+				ti,channel0-current-microamp = <5>;
+				ti,channel3-current-microamp = <400>;
+				ti,enable-extended-delay;
+
+				#io-channel-cells = <1>;
+			};
+
+			palmas_extcon: extcon {
+				compatible = "ti,palmas-usb-vid";
+				ti,enable-vbus-detection;
+				ti,enable-id-detection;
+			};
+
+			palmas_gpio: gpio {
+				compatible = "ti,palmas-gpio";
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			palmas_clk32kg@0 {
+				compatible = "ti,palmas-clk32kg";
+				#clock-cells = <0>;
+			};
+
+			pinmux {
+				compatible = "ti,tps65913-pinctrl";
+				ti,palmas-enable-dvfs1;
+
+				pinctrl-names = "default";
+				pinctrl-0 = <&palmas_default>;
+
+				palmas_default: pinmux {
+					pin_gpio0 {
+						pins = "gpio0";
+						function = "gpio";
+					};
+
+					pin_gpio1 {
+						pins = "gpio1";
+						function = "gpio";
+					};
+
+					pin_gpio2 {
+						pins = "gpio2";
+						function = "gpio";
+					};
+
+					pin_gpio3 {
+						pins = "gpio3";
+						function = "gpio";
+					};
+
+					pin_gpio4 {
+						pins = "gpio4";
+						function = "gpio";
+					};
+
+					pin_gpio5 {
+						pins = "gpio5";
+						function = "gpio";
+					};
+
+					pin_gpio6 {
+						pins = "gpio6";
+						function = "gpio";
+					};
+
+					pin_gpio7 {
+						pins = "gpio7";
+						function = "gpio";
+					};
+
+					pin_powergood {
+						pins = "powergood";
+						function = "powergood";
+					};
+
+					pin_vac {
+						pins = "vac";
+						function = "vac";
+					};
+				};
+			};
+
+			pmic {
+				compatible = "ti,tps65913-pmic", "ti,palmas-pmic";
+
+				ldo1-in-supply = <&vddio_ddr>;
+				ldo2-in-supply = <&vddio_ddr>;
+				ldo4-in-supply = <&vdd_1v8_vio>;
+				ldo5-in-supply = <&vcore_emmc>;
+				ldo6-in-supply = <&vcore_emmc>;
+				ldo7-in-supply = <&vcore_emmc>;
+				ldo9-in-supply = <&vcore_emmc>;
+				ldoln-in-supply = <&vdd_smps10_out2>;
+
+				regulators {
+					vdd_cpu: smps123 {
+						regulator-name = "vdd_cpu";
+						regulator-min-microvolt = <900000>;
+						regulator-max-microvolt = <1350000>;
+						regulator-always-on;
+						regulator-boot-on;
+						ti,roof-floor = <1>;
+						ti,mode-sleep = <3>;
+					};
+
+					vdd_core: smps45 {
+						regulator-name = "vdd_core";
+						regulator-min-microvolt = <900000>;
+						regulator-max-microvolt = <1400000>;
+						regulator-always-on;
+						regulator-boot-on;
+						ti,roof-floor = <3>;
+					};
+
+					/* smps6 disabled */
+
+					vddio_ddr: smps7 {
+						regulator-name = "vddio_ddr";
+						regulator-min-microvolt = <1350000>;
+						regulator-max-microvolt = <1350000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					vdd_1v8_vio: smps8 {
+						regulator-name = "vdd_1v8";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					vcore_emmc: smps9 {
+						regulator-name = "vdd_emmc";
+						regulator-min-microvolt = <2900000>;
+						regulator-max-microvolt = <2900000>;
+						regulator-boot-on;
+					};
+
+					smps10_out1 {
+						regulator-name = "vd_smps10_out1";
+						regulator-min-microvolt = <5000000>;
+						regulator-max-microvolt = <5000000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					vdd_smps10_out2: smps10_out2 {
+						regulator-name = "vd_smps10_out2";
+						regulator-min-microvolt = <5000000>;
+						regulator-max-microvolt = <5000000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					avdd_hdmi_pll: ldo1 {
+						regulator-name = "avdd_hdmi_pll";
+						regulator-min-microvolt = <1050000>;
+						regulator-max-microvolt = <1050000>;
+						regulator-always-on;
+						regulator-boot-on;
+						ti,roof-floor = <3>;
+					};
+
+					avdd_dsi_csi: ldo2 {
+						regulator-name = "avdd_dsi_csi";
+						regulator-min-microvolt = <1200000>;
+						regulator-max-microvolt = <1200000>;
+						regulator-boot-on;
+					};
+
+					ldo3 {
+						regulator-name = "vpp_fuse";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					vdd_1v2_cam: ldo4 {
+						regulator-name = "vdd_1v2_cam";
+						regulator-min-microvolt = <1200000>;
+						regulator-max-microvolt = <1200000>;
+					};
+
+					avdd_2v8_cam: ldo5 {
+						regulator-name = "avdd_cam2";
+						regulator-min-microvolt = <2800000>;
+						regulator-max-microvolt = <2800000>;
+					};
+
+					vdd_2v85_sen: ldo6 {
+						regulator-name = "vdd_dev";
+						regulator-min-microvolt = <2850000>;
+						regulator-max-microvolt = <2850000>;
+					};
+
+					avdd_2v8_af: ldo7 {
+						regulator-name = "avdd_2v8_cam";
+						regulator-min-microvolt = <2800000>;
+						regulator-max-microvolt = <2800000>;
+					};
+
+					ldo8 {
+						regulator-name = "vdd_rtc";
+						regulator-min-microvolt = <950000>;
+						regulator-max-microvolt = <950000>;
+						regulator-always-on;
+						regulator-boot-on;
+						ti,enable-ldo8-tracking;
+					};
+
+					vddio_usd: ldo9 {
+						regulator-name = "vddio_usd";
+						/* min voltage of 1.8v is not stable */
+						regulator-min-microvolt = <2900000>;
+						regulator-max-microvolt = <2900000>;
+					};
+
+					avdd_hdmi: ldoln {
+						regulator-name = "avdd_hdmi";
+						regulator-min-microvolt = <3300000>;
+						regulator-max-microvolt = <3300000>;
+						regulator-boot-on;
+					};
+
+					avdd_usb: ldousb {
+						regulator-name = "avdd_usb";
+						regulator-min-microvolt = <3300000>;
+						regulator-max-microvolt = <3300000>;
+						regulator-boot-on;
+					};
+				};
+			};
+
+			rtc {
+				compatible = "ti,palmas-rtc";
+				interrupt-parent = <&palmas>;
+				interrupts = <8 IRQ_TYPE_NONE>;
+			};
+		};
+	};
+
+	pmc@7000e400 {
+		status = "okay";
+		nvidia,suspend-mode = <2>;
+		nvidia,cpu-pwr-good-time = <300>;
+		nvidia,cpu-pwr-off-time = <300>;
+		nvidia,core-pwr-good-time = <641 3845>;
+		nvidia,core-pwr-off-time = <2000>;
+		nvidia,core-power-req-active-high;
+		nvidia,sys-clock-req-active-high;
+
+		/* Clear DEV_ON bit in DEV_CTRL register of TPS65913 PMIC  */
+		i2c-thermtrip {
+			nvidia,i2c-controller-id = <4>;
+			nvidia,bus-addr = <0x58>;
+			nvidia,reg-addr = <0xA0>;
+			nvidia,reg-data = <0x00>;
+		};
+	};
+
+	ahub@70080000 {
+		/* HIFI CODEC (i2s1) */
+		i2s@70080400 {
+			status = "okay";
+		};
+
+		/* BT SCO (i2s3) */
+		i2s@70080600 {
+			status = "okay";
+		};
+	};
+
+	brcm_wifi_pwrseq: pwrseq-wifi {
+		compatible = "mmc-pwrseq-simple";
+
+		clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
+		clock-names = "ext_clock";
+
+		reset-gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <300>;
+		power-off-delay-us = <300>;
+	};
+
+	/* WiFi */
+	mmc@78000000 {
+		status = "okay";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		assigned-clocks = <&tegra_car TEGRA114_CLK_SDMMC1>;
+		assigned-clock-parents = <&tegra_car TEGRA114_CLK_PLL_P>;
+		assigned-clock-rates = <82000000>;
+
+		max-frequency = <82000000>;
+		keep-power-in-suspend;
+		bus-width = <4>;
+		non-removable;
+
+		sd-uhs-ddr50;
+		mmc-ddr-1_8v;
+
+		power-gpios = <&gpio TEGRA_GPIO(CC, 5) GPIO_ACTIVE_HIGH>;
+
+		nvidia,default-tap = <0x2>;
+		nvidia,default-trim = <0x2>;
+
+		mmc-pwrseq = <&brcm_wifi_pwrseq>;
+		vmmc-supply = <&vdd_3v3_com>;
+		vqmmc-supply = <&vdd_1v8_vio>;
+
+		wifi@1 {
+			compatible = "brcm,bcm4329-fmac";
+			reg = <1>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(U, 5) IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "host-wake";
+		};
+	};
+
+	/* MicroSD card */
+	mmc@78000400 {
+		status = "okay";
+
+		bus-width = <4>;
+		cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
+
+		nvidia,default-tap = <0x3>;
+		nvidia,default-trim = <0x3>;
+
+		vmmc-supply = <&vdd_2v9_usd>;
+		vqmmc-supply = <&vddio_usd>;
+	};
+
+	/* eMMC */
+	mmc@78000600 {
+		status = "okay";
+		bus-width = <8>;
+
+		non-removable;
+		mmc-ddr-1_8v;
+
+		vmmc-supply = <&vcore_emmc>;
+		vqmmc-supply = <&vdd_1v8_vio>;
+	};
+
+	/* Peripheral USB via ASUS connector */
+	usb@7d000000 {
+		compatible = "nvidia,tegra114-udc";
+		status = "okay";
+		dr_mode = "peripheral";
+	};
+
+	usb-phy@7d000000 {
+		status = "okay";
+		dr_mode = "peripheral";
+		vbus-supply = <&avdd_usb>;
+	};
+
+	/* Host USB via dock */
+	usb@7d008000 {
+		status = "okay";
+	};
+
+	usb-phy@7d008000 {
+		status = "okay";
+		vbus-supply = <&vdd_5v0_sys>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+
+		power-supply = <&vdd_3v7_bl>;
+		pwms = <&pwm 1 1000000>;
+
+		brightness-levels = <1 255>;
+		num-interpolated-steps = <254>;
+		default-brightness-level = <224>;
+	};
+
+	/* PMIC has a built-in 32KHz oscillator which is used by PMC */
+	clk32k_in: clock-32k {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "pmic-oscillator";
+	};
+
+	connector {
+		compatible = "hdmi-connector";
+		type = "d";
+
+		hpd-gpios = <&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>;
+		ddc-i2c-bus = <&hdmi_ddc>;
+
+		port {
+			connector_in: endpoint {
+				remote-endpoint = <&hdmi_out>;
+			};
+		};
+	};
+
+	extcon-keys {
+		compatible = "gpio-keys";
+
+		switch-hall-sensor {
+			label = "Hall Effect Sensor";
+			gpios = <&gpio TEGRA_GPIO(O, 5) GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			linux,can-disable;
+			wakeup-source;
+		};
+
+		switch-lineout-detect {
+			label = "Audio dock line-out detect";
+			gpios = <&gpio TEGRA_GPIO(X, 5) GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LINEOUT_INSERT>;
+			debounce-interval = <10>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-power {
+			label = "Power";
+			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			debounce-interval = <10>;
+			wakeup-source;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio TEGRA_GPIO(R, 1) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <10>;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio TEGRA_GPIO(R, 2) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <10>;
+		};
+	};
+
+	sound {
+		compatible = "asus,tegra-audio-rt5639-tf701t",
+			     "nvidia,tegra-audio-rt5640";
+		nvidia,model = "Asus Transformer Pad TF701T RT5639";
+
+		nvidia,audio-routing =
+			"Headphones", "HPOR",
+			"Headphones", "HPOL",
+			"Speakers", "SPORP",
+			"Speakers", "SPORN",
+			"Speakers", "SPOLP",
+			"Speakers", "SPOLN",
+			"IN1P", "Mic Jack",
+			"IN1N", "Mic Jack",
+			"DMIC1", "Int Mic",
+			"DMIC2", "Int Mic";
+
+		nvidia,i2s-controller = <&tegra_i2s1>;
+		nvidia,audio-codec = <&rt5639>;
+
+		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(R, 7) GPIO_ACTIVE_LOW>;
+		nvidia,int-mic-en-gpios = <&gpio TEGRA_GPIO(K, 3) GPIO_ACTIVE_HIGH>;
+
+		clocks = <&tegra_car TEGRA114_CLK_PLL_A>,
+			 <&tegra_car TEGRA114_CLK_PLL_A_OUT0>,
+			 <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+		clock-names = "pll_a", "pll_a_out0", "mclk";
+
+		assigned-clocks = <&tegra_car TEGRA114_CLK_EXTERN1>,
+				  <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+
+		assigned-clock-parents = <&tegra_car TEGRA114_CLK_PLL_A_OUT0>,
+					 <&tegra_car TEGRA114_CLK_EXTERN1>;
+	};
+
+	vdd_5v0_sys: regulator-5v0-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_3v3_sys: regulator-3v3-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3_sys";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	dvdd_1v8_lcd: regulator-vdd-lcd {
+		compatible = "regulator-fixed";
+		regulator-name = "dvdd_1v8_lcd";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		gpio = <&palmas_gpio 4 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_1v8_vio>;
+	};
+
+	vdd_3v7_bl: regulator-bl-en {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v7_bl";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+		regulator-boot-on;
+		gpio = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_sys>;
+	};
+
+	hdmi_5v0_sys: regulator-hdmi {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0_hdmi";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_smps10_out2>;
+	};
+
+	vdd_2v9_usd: regulator-vdd-usd {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_sd_slot";
+		regulator-min-microvolt = <2900000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-boot-on;
+		gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vcore_emmc>;
+	};
+
+	vdd_1v8_cam: regulator-cam-vio {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_1v8_cam";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		gpio = <&palmas_gpio 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_1v8_vio>;
+	};
+
+	vdd_1v2_xusb: regulator-xusb-vio {
+		compatible = "regulator-fixed";
+		regulator-name = "avddio_1v2_xusb";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-boot-on;
+		gpio = <&palmas_gpio 3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vdd_3v3_xusb: regulator-xusb-vdd {
+		compatible = "regulator-fixed";
+		regulator-name = "hvdd_3v3_xusb";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		gpio = <&palmas_gpio 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vdd_3v3_com: regulator-com {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3_com";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&gpio TEGRA_GPIO(U, 1) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_sys>;
+	};
+
+	vdd_3v3_touch: regulator-touch-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3_touch";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		gpio = <&gpio TEGRA_GPIO(H, 0) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_sys>;
+	};
+
+	vdd_1v8_touch: regulator-touch-vio {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_1v8_touch";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		gpio = <&gpio TEGRA_GPIO(H, 4) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_sys>;
+	};
+};
diff --git a/arch/arm/boot/dts/tegra114-dalmore.dts b/arch/arm/boot/dts/nvidia/tegra114-dalmore.dts
index 658edfb8d7fa..c06b52fe330a 100644
--- a/arch/arm/boot/dts/tegra114-dalmore.dts
+++ b/arch/arm/boot/dts/nvidia/tegra114-dalmore.dts
@@ -755,6 +755,8 @@
 	};
 
 	serial@70006300 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -909,6 +911,19 @@
 				#gpio-cells = <2>;
 			};
 
+			pinmux {
+				compatible = "ti,tps65913-pinctrl";
+				pinctrl-names = "default";
+				pinctrl-0 = <&palmas_default>;
+
+				palmas_default: pinmux {
+					pin_gpio6 {
+						pins = "gpio6";
+						function = "gpio";
+					};
+				};
+			};
+
 			pmic {
 				compatible = "ti,tps65913-pmic", "ti,palmas-pmic";
 				smps1-in-supply = <&tps65090_dcdc3_reg>;
@@ -1065,19 +1080,6 @@
 				interrupt-parent = <&palmas>;
 				interrupts = <8 0>;
 			};
-
-			pinmux {
-				compatible = "ti,tps65913-pinctrl";
-				pinctrl-names = "default";
-				pinctrl-0 = <&palmas_default>;
-
-				palmas_default: pinmux {
-					pin_gpio6 {
-						pins = "gpio6";
-						function = "gpio";
-					};
-				};
-			};
 		};
 	};
 
@@ -1161,26 +1163,26 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		home {
+		key-home {
 			label = "Home";
 			gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_HOME>;
 		};
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			wakeup-source;
 		};
 
-		volume_down {
+		key-volume-down {
 			label = "Volume Down";
 			gpios = <&gpio TEGRA_GPIO(R, 1) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
 		};
 
-		volume_up {
+		key-volume-up {
 			label = "Volume Up";
 			gpios = <&gpio TEGRA_GPIO(R, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
diff --git a/arch/arm/boot/dts/tegra114-roth.dts b/arch/arm/boot/dts/nvidia/tegra114-roth.dts
index 2498cf18fd39..a89b16573b42 100644
--- a/arch/arm/boot/dts/tegra114-roth.dts
+++ b/arch/arm/boot/dts/nvidia/tegra114-roth.dts
@@ -779,6 +779,8 @@
 
 	/* Usable on reworked devices only */
 	serial@70006300 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -1025,19 +1027,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		back {
+		key-back {
 			label = "Back";
 			gpios = <&gpio TEGRA_GPIO(R, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_BACK>;
 		};
 
-		home {
+		key-home {
 			label = "Home";
 			gpios = <&gpio TEGRA_GPIO(R, 1) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_HOME>;
 		};
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
diff --git a/arch/arm/boot/dts/tegra114-tn7.dts b/arch/arm/boot/dts/nvidia/tegra114-tn7.dts
index ef8f722dd9cb..bfbdb345575a 100644
--- a/arch/arm/boot/dts/tegra114-tn7.dts
+++ b/arch/arm/boot/dts/nvidia/tegra114-tn7.dts
@@ -50,6 +50,8 @@
 	};
 
 	serial@70006300 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -282,20 +284,20 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			wakeup-source;
 		};
 
-		volume_down {
+		key-volume-down {
 			label = "Volume Down";
 			gpios = <&gpio TEGRA_GPIO(Q, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
 		};
 
-		volume_up {
+		key-volume-up {
 			label = "Volume Up";
 			gpios = <&gpio TEGRA_GPIO(R, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
diff --git a/arch/arm/boot/dts/tegra114.dtsi b/arch/arm/boot/dts/nvidia/tegra114.dtsi
index 09996acad639..a2a50f959927 100644
--- a/arch/arm/boot/dts/tegra114.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra114.dtsi
@@ -4,6 +4,7 @@
 #include <dt-bindings/memory/tegra114-mc.h>
 #include <dt-bindings/pinctrl/pinctrl-tegra.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/reset/nvidia,tegra114-car.h>
 #include <dt-bindings/soc/tegra-pmc.h>
 
 / {
@@ -139,7 +140,7 @@
 			reg = <0x54400000 0x00040000>;
 			clocks = <&tegra_car TEGRA114_CLK_DSIB>,
 				 <&tegra_car TEGRA114_CLK_DSIBLP>,
-				 <&tegra_car TEGRA114_CLK_PLL_D2_OUT0>;
+				 <&tegra_car TEGRA114_CLK_PLL_D_OUT0>;
 			clock-names = "dsi", "lp", "parent";
 			resets = <&tegra_car 82>;
 			reset-names = "dsi";
@@ -315,7 +316,6 @@
 		interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA114_CLK_UARTA>;
 		resets = <&tegra_car 6>;
-		reset-names = "serial";
 		dmas = <&apbdma 8>, <&apbdma 8>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -328,7 +328,6 @@
 		interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA114_CLK_UARTB>;
 		resets = <&tegra_car 7>;
-		reset-names = "serial";
 		dmas = <&apbdma 9>, <&apbdma 9>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -341,7 +340,6 @@
 		interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA114_CLK_UARTC>;
 		resets = <&tegra_car 55>;
-		reset-names = "serial";
 		dmas = <&apbdma 10>, <&apbdma 10>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -354,7 +352,6 @@
 		interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA114_CLK_UARTD>;
 		resets = <&tegra_car 65>;
-		reset-names = "serial";
 		dmas = <&apbdma 19>, <&apbdma 19>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -581,6 +578,21 @@
 		#iommu-cells = <1>;
 	};
 
+	hda@70030000 {
+		compatible = "nvidia,tegra114-hda", "nvidia,tegra30-hda";
+		reg = <0x70030000 0x10000>;
+		interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&tegra_car TEGRA114_CLK_HDA>,
+			 <&tegra_car TEGRA114_CLK_HDA2HDMI>,
+			 <&tegra_car TEGRA114_CLK_HDA2CODEC_2X>;
+		clock-names = "hda", "hda2hdmi", "hda2codec_2x";
+		resets = <&tegra_car 125>, /* hda */
+			 <&tegra_car 128>, /* hda2hdmi */
+			 <&tegra_car 111>; /* hda2codec_2x */
+		reset-names = "hda", "hda2hdmi", "hda2codec_2x";
+		status = "disabled";
+	};
+
 	ahub@70080000 {
 		compatible = "nvidia,tegra114-ahub";
 		reg = <0x70080000 0x200>,
@@ -682,6 +694,29 @@
 		#nvidia,mipi-calibrate-cells = <1>;
 	};
 
+	dfll: clock@70110000 {
+		compatible = "nvidia,tegra114-dfll";
+		reg = <0x70110000 0x100>, /* DFLL control */
+		      <0x70110000 0x100>, /* I2C output control */
+		      <0x70110100 0x100>, /* Integrated I2C controller */
+		      <0x70110200 0x100>; /* Look-up table RAM */
+		interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&tegra_car TEGRA114_CLK_DFLL_SOC>,
+			 <&tegra_car TEGRA114_CLK_DFLL_REF>,
+			 <&tegra_car TEGRA114_CLK_I2C5>;
+		clock-names = "soc", "ref", "i2c";
+		resets = <&tegra_car TEGRA114_RST_DFLL_DVCO>;
+		reset-names = "dvco";
+		#clock-cells = <0>;
+		clock-output-names = "dfllCPU_out";
+		nvidia,droop-ctrl = <0x00000f00>;
+		nvidia,force-mode = <1>;
+		nvidia,cf = <10>;
+		nvidia,ci = <0>;
+		nvidia,cg = <2>;
+		status = "disabled";
+	};
+
 	mmc@78000000 {
 		compatible = "nvidia,tegra114-sdhci";
 		reg = <0x78000000 0x200>;
@@ -809,31 +844,49 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu@0 {
+		cpu0: cpu@0 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0>;
+
+			clocks = <&tegra_car TEGRA114_CLK_CCLK_G>,
+				 <&tegra_car TEGRA114_CLK_CCLK_LP>,
+				 <&tegra_car TEGRA114_CLK_PLL_X>,
+				 <&tegra_car TEGRA114_CLK_PLL_P>,
+				 <&dfll>;
+			clock-names = "cpu_g", "cpu_lp", "pll_x", "pll_p", "dfll";
+			/* FIXME: what's the actual transition time? */
+			clock-latency = <300000>;
 		};
 
-		cpu@1 {
+		cpu1: cpu@1 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <1>;
 		};
 
-		cpu@2 {
+		cpu2: cpu@2 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <2>;
 		};
 
-		cpu@3 {
+		cpu3: cpu@3 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <3>;
 		};
 	};
 
+	pmu {
+		compatible = "arm,cortex-a15-pmu";
+		interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
 	timer {
 		compatible = "arm,armv7-timer";
 		interrupts =
diff --git a/arch/arm/boot/dts/tegra124-apalis-emc.dtsi b/arch/arm/boot/dts/nvidia/tegra124-apalis-emc.dtsi
index 7143c6b2ec3e..970f33dd9101 100644
--- a/arch/arm/boot/dts/tegra124-apalis-emc.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra124-apalis-emc.dtsi
@@ -4,6 +4,8 @@
  *
  */
 
+#include <dt-bindings/clock/tegra124-car.h>
+
 / {
 	clock@60006000 {
 		emc-timings-1 {
@@ -1474,12 +1476,12 @@
 			};
 		};
 	};
-};
 
-&emc_icc_dvfs_opp_table {
-	/delete-node/ opp-1200000000-1100;
-};
+	opp-table-actmon {
+		/delete-node/ opp-1200000000;
+	};
 
-&emc_bw_dfs_opp_table {
-	/delete-node/ opp-1200000000;
+	opp-table-emc {
+		/delete-node/ opp-1200000000-1100;
+	};
 };
diff --git a/arch/arm/boot/dts/tegra124-apalis-eval.dts b/arch/arm/boot/dts/nvidia/tegra124-apalis-eval.dts
index 3209554ec7e6..1aa7265554d9 100644
--- a/arch/arm/boot/dts/tegra124-apalis-eval.dts
+++ b/arch/arm/boot/dts/nvidia/tegra124-apalis-eval.dts
@@ -40,8 +40,20 @@
 		};
 	};
 
+	gpio: gpio@6000d000 {
+		/* Apalis GPIO7 MXM3 pin 15 PLX PEX 8605 PCIe Switch Reset */
+		pex-perst-n-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(DD, 1) GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "PEX_PERST_N";
+		};
+	};
+
 	/* Apalis UART1 */
 	serial@70006000 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -72,11 +84,6 @@
 		status = "okay";
 		clock-frequency = <400000>;
 
-		pcie-switch@58 {
-			compatible = "plx,pex8605";
-			reg = <0x58>;
-		};
-
 		/* M41T0M6 real time clock on carrier board */
 		rtc@68 {
 			compatible = "st,m41t0";
@@ -191,7 +198,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "WAKE1_MICO";
 			gpios = <&gpio TEGRA_GPIO(DD, 3) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_WAKEUP>;
@@ -243,13 +250,3 @@
 		vin-supply = <&reg_5v0>;
 	};
 };
-
-&gpio {
-	/* Apalis GPIO7 MXM3 pin 15 PLX PEX 8605 PCIe Switch Reset */
-	pex-perst-n-hog {
-		gpio-hog;
-		gpios = <TEGRA_GPIO(DD, 1) GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "PEX_PERST_N";
-	};
-};
diff --git a/arch/arm/boot/dts/tegra124-apalis-v1.2-eval.dts b/arch/arm/boot/dts/nvidia/tegra124-apalis-v1.2-eval.dts
index 814257c79bf1..23158bb82173 100644
--- a/arch/arm/boot/dts/tegra124-apalis-v1.2-eval.dts
+++ b/arch/arm/boot/dts/nvidia/tegra124-apalis-v1.2-eval.dts
@@ -41,8 +41,20 @@
 		};
 	};
 
+	gpio@6000d000 {
+		/* Apalis GPIO7 MXM3 pin 15 PLX PEX 8605 PCIe Switch Reset */
+		pex-perst-n-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(DD, 1) GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "PEX_PERST_N";
+		};
+	};
+
 	/* Apalis UART1 */
 	serial@70006000 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -73,11 +85,6 @@
 		status = "okay";
 		clock-frequency = <400000>;
 
-		pcie-switch@58 {
-			compatible = "plx,pex8605";
-			reg = <0x58>;
-		};
-
 		/* M41T0M6 real time clock on carrier board */
 		rtc@68 {
 			compatible = "st,m41t0";
@@ -193,7 +200,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "WAKE1_MICO";
 			gpios = <&gpio TEGRA_GPIO(DD, 3) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_WAKEUP>;
@@ -245,13 +252,3 @@
 		vin-supply = <&reg_5v0>;
 	};
 };
-
-&gpio {
-	/* Apalis GPIO7 MXM3 pin 15 PLX PEX 8605 PCIe Switch Reset */
-	pex-perst-n-hog {
-		gpio-hog;
-		gpios = <TEGRA_GPIO(DD, 1) GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "PEX_PERST_N";
-	};
-};
diff --git a/arch/arm/boot/dts/tegra124-apalis-v1.2.dtsi b/arch/arm/boot/dts/nvidia/tegra124-apalis-v1.2.dtsi
index dbb0da08cb95..54b7da4b6920 100644
--- a/arch/arm/boot/dts/tegra124-apalis-v1.2.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra124-apalis-v1.2.dtsi
@@ -65,6 +65,24 @@
 		vdd-supply = <&reg_vdd_gpu>;
 	};
 
+	gpio@6000d000 {
+		/* I210 Gigabit Ethernet Controller Reset */
+		lan-reset-n-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(S, 2) GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "LAN_RESET_N";
+		};
+
+		/* Control MXM3 pin 26 Reset Module Output Carrier Input */
+		reset-moci-ctrl-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(U, 4) GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "RESET_MOCI_CTRL";
+		};
+	};
+
 	pinmux@70000868 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&state_default>;
@@ -1539,16 +1557,19 @@
 
 	serial@70006040 {
 		compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 	};
 
 	serial@70006200 {
 		compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 	};
 
 	serial@70006300 {
 		compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 	};
 
@@ -1585,18 +1606,18 @@
 			pinctrl-0 = <&as3722_default>;
 
 			as3722_default: pinmux {
+				gpio0-1-3-4-5-6 {
+					pins = "gpio0", "gpio1", "gpio3",
+					       "gpio4", "gpio5", "gpio6";
+					bias-high-impedance;
+				};
+
 				gpio2-7 {
 					pins = "gpio2", /* PWR_EN_+V3.3 */
 					       "gpio7"; /* +V1.6_LPO */
 					function = "gpio";
 					bias-pull-up;
 				};
-
-				gpio0-1-3-4-5-6 {
-					pins = "gpio0", "gpio1", "gpio3",
-					       "gpio4", "gpio5", "gpio6";
-					bias-high-impedance;
-				};
 			};
 
 			regulators {
@@ -1943,18 +1964,18 @@
 		};
 	};
 
-	clk32k_in: osc3 {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <32768>;
-	};
-
 	cpus {
 		cpu@0 {
 			vdd-cpu-supply = <&reg_vdd_cpu>;
 		};
 	};
 
+	clk32k_in: osc3 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
+
 	reg_1v05_avdd_hdmi_pll: regulator-1v05-avdd-hdmi-pll {
 		compatible = "regulator-fixed";
 		regulator-name = "+V1.05_AVDD_HDMI_PLL";
@@ -2056,21 +2077,3 @@
 		};
 	};
 };
-
-&gpio {
-	/* I210 Gigabit Ethernet Controller Reset */
-	lan-reset-n-hog {
-		gpio-hog;
-		gpios = <TEGRA_GPIO(S, 2) GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "LAN_RESET_N";
-	};
-
-	/* Control MXM3 pin 26 Reset Module Output Carrier Input */
-	reset-moci-ctrl-hog {
-		gpio-hog;
-		gpios = <TEGRA_GPIO(U, 4) GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "RESET_MOCI_CTRL";
-	};
-};
diff --git a/arch/arm/boot/dts/tegra124-apalis.dtsi b/arch/arm/boot/dts/nvidia/tegra124-apalis.dtsi
index d3f16c117b0c..c5a0d6aebaec 100644
--- a/arch/arm/boot/dts/tegra124-apalis.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra124-apalis.dtsi
@@ -64,6 +64,24 @@
 		vdd-supply = <&reg_vdd_gpu>;
 	};
 
+	gpio@6000d000 {
+		/* I210 Gigabit Ethernet Controller Reset */
+		lan-reset-n-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(S, 2) GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "LAN_RESET_N";
+		};
+
+		/* Control MXM3 pin 26 Reset Module Output Carrier Input */
+		reset-moci-ctrl-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(U, 4) GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "RESET_MOCI_CTRL";
+		};
+	};
+
 	pinmux@70000868 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&state_default>;
@@ -1532,16 +1550,19 @@
 
 	serial@70006040 {
 		compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 	};
 
 	serial@70006200 {
 		compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 	};
 
 	serial@70006300 {
 		compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 	};
 
@@ -1578,18 +1599,18 @@
 			pinctrl-0 = <&as3722_default>;
 
 			as3722_default: pinmux {
+				gpio0-1-3-4-5-6 {
+					pins = "gpio0", "gpio1", "gpio3",
+					       "gpio4", "gpio5", "gpio6";
+					bias-high-impedance;
+				};
+
 				gpio2-7 {
 					pins = "gpio2", /* PWR_EN_+V3.3 */
 					       "gpio7"; /* +V1.6_LPO */
 					function = "gpio";
 					bias-pull-up;
 				};
-
-				gpio0-1-3-4-5-6 {
-					pins = "gpio0", "gpio1", "gpio3",
-					       "gpio4", "gpio5", "gpio6";
-					bias-high-impedance;
-				};
 			};
 
 			regulators {
@@ -1935,18 +1956,18 @@
 		};
 	};
 
-	clk32k_in: osc3 {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <32768>;
-	};
-
 	cpus {
 		cpu@0 {
 			vdd-cpu-supply = <&reg_vdd_cpu>;
 		};
 	};
 
+	clk32k_in: osc3 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
+
 	reg_1v05_avdd_hdmi_pll: regulator-1v05-avdd-hdmi-pll {
 		compatible = "regulator-fixed";
 		regulator-name = "+V1.05_AVDD_HDMI_PLL";
@@ -2048,21 +2069,3 @@
 		};
 	};
 };
-
-&gpio {
-	/* I210 Gigabit Ethernet Controller Reset */
-	lan-reset-n-hog {
-		gpio-hog;
-		gpios = <TEGRA_GPIO(S, 2) GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "LAN_RESET_N";
-	};
-
-	/* Control MXM3 pin 26 Reset Module Output Carrier Input */
-	reset-moci-ctrl-hog {
-		gpio-hog;
-		gpios = <TEGRA_GPIO(U, 4) GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "RESET_MOCI_CTRL";
-	};
-};
diff --git a/arch/arm/boot/dts/tegra124-jetson-tk1-emc.dtsi b/arch/arm/boot/dts/nvidia/tegra124-jetson-tk1-emc.dtsi
index 79e776db5f37..d10e5334a6c6 100644
--- a/arch/arm/boot/dts/tegra124-jetson-tk1-emc.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra124-jetson-tk1-emc.dtsi
@@ -1,4 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
+
+#include <dt-bindings/clock/tegra124-car.h>
+
 / {
 	clock@60006000 {
 		emc-timings-3 {
@@ -2429,12 +2432,12 @@
 			};
 		};
 	};
-};
 
-&emc_icc_dvfs_opp_table {
-	/delete-node/ opp-1200000000-1100;
-};
+	opp-table-actmon {
+		/delete-node/ opp-1200000000;
+	};
 
-&emc_bw_dfs_opp_table {
-	/delete-node/ opp-1200000000;
+	opp-table-emc {
+		/delete-node/ opp-1200000000-1100;
+	};
 };
diff --git a/arch/arm/boot/dts/tegra124-jetson-tk1.dts b/arch/arm/boot/dts/nvidia/tegra124-jetson-tk1.dts
index 28b889e4e33b..f09109be1152 100644
--- a/arch/arm/boot/dts/tegra124-jetson-tk1.dts
+++ b/arch/arm/boot/dts/nvidia/tegra124-jetson-tk1.dts
@@ -68,10 +68,6 @@
 		};
 	};
 
-	cec@70015000 {
-		status = "okay";
-	};
-
 	gpu@57000000 {
 		/*
 		 * Node left disabled on purpose - the bootloader will enable
@@ -1389,6 +1385,7 @@
 	 */
 	serial@70006000 {
 		compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 		status = "okay";
 	};
@@ -1402,12 +1399,15 @@
 	 */
 	serial@70006040 {
 		compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 		status = "okay";
 	};
 
 	/* DB9 serial port */
 	serial@70006300 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -1683,6 +1683,10 @@
 		};
 	};
 
+	cec@70015000 {
+		status = "okay";
+	};
+
 	/* Serial ATA */
 	sata@70020000 {
 		status = "okay";
@@ -1886,7 +1890,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
diff --git a/arch/arm/boot/dts/tegra124-nyan-big-emc.dtsi b/arch/arm/boot/dts/nvidia/tegra124-nyan-big-emc.dtsi
index 31b2e26c69d4..cadb1969f1cc 100644
--- a/arch/arm/boot/dts/tegra124-nyan-big-emc.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra124-nyan-big-emc.dtsi
@@ -1,9 +1,8 @@
 // SPDX-License-Identifier: GPL-2.0
-/ {
-	apbmisc@70000800 {
-		nvidia,long-ram-code;
-	};
 
+#include <dt-bindings/clock/tegra124-car.h>
+
+/ {
 	clock@60006000 {
 		emc-timings-1 {
 			nvidia,ram-code = <1>;
@@ -249,6 +248,10 @@
 		};
 	};
 
+	apbmisc@70000800 {
+		nvidia,long-ram-code;
+	};
+
 	memory-controller@70019000 {
 		emc-timings-1 {
 			nvidia,ram-code = <1>;
@@ -6678,14 +6681,14 @@
 			};
 		};
 	};
-};
 
-&emc_icc_dvfs_opp_table {
-	/delete-node/ opp-924000000-1100;
-	/delete-node/ opp-1200000000-1100;
-};
+	opp-table-actmon {
+		/delete-node/ opp-924000000;
+		/delete-node/ opp-1200000000;
+	};
 
-&emc_bw_dfs_opp_table {
-	/delete-node/ opp-924000000;
-	/delete-node/ opp-1200000000;
+	opp-table-emc {
+		/delete-node/ opp-924000000-1100;
+		/delete-node/ opp-1200000000-1100;
+	};
 };
diff --git a/arch/arm/boot/dts/tegra124-nyan-big-fhd.dts b/arch/arm/boot/dts/nvidia/tegra124-nyan-big-fhd.dts
index 4db43324dafa..4db43324dafa 100644
--- a/arch/arm/boot/dts/tegra124-nyan-big-fhd.dts
+++ b/arch/arm/boot/dts/nvidia/tegra124-nyan-big-fhd.dts
diff --git a/arch/arm/boot/dts/tegra124-nyan-big.dts b/arch/arm/boot/dts/nvidia/tegra124-nyan-big.dts
index fdc1d64dfff9..8bca9599ad6e 100644
--- a/arch/arm/boot/dts/tegra124-nyan-big.dts
+++ b/arch/arm/boot/dts/nvidia/tegra124-nyan-big.dts
@@ -18,28 +18,18 @@
 			aux-bus {
 				panel: panel {
 					compatible = "auo,b133xtn01";
+					power-supply = <&vdd_3v3_panel>;
 					backlight = <&backlight>;
 				};
 			};
 		};
 	};
 
-	mmc@700b0400 { /* SD Card on this bus */
-		wp-gpios = <&gpio TEGRA_GPIO(Q, 4) GPIO_ACTIVE_LOW>;
-	};
-
-	sound {
-		compatible = "nvidia,tegra-audio-max98090-nyan-big",
-			     "nvidia,tegra-audio-max98090-nyan",
-			     "nvidia,tegra-audio-max98090";
-		nvidia,model = "GoogleNyanBig";
-	};
-
 	pinmux@70000868 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinmux_default>;
 
-		pinmux_default: common {
+		pinmux_default: pinmux {
 			clk_32k_out_pa0 {
 				nvidia,pins = "clk_32k_out_pa0";
 				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
@@ -1344,4 +1334,15 @@
 			};
 		};
 	};
+
+	mmc@700b0400 { /* SD Card on this bus */
+		wp-gpios = <&gpio TEGRA_GPIO(Q, 4) GPIO_ACTIVE_LOW>;
+	};
+
+	sound {
+		compatible = "nvidia,tegra-audio-max98090-nyan-big",
+			     "nvidia,tegra-audio-max98090-nyan",
+			     "nvidia,tegra-audio-max98090";
+		nvidia,model = "GoogleNyanBig";
+	};
 };
diff --git a/arch/arm/boot/dts/tegra124-nyan-blaze-emc.dtsi b/arch/arm/boot/dts/nvidia/tegra124-nyan-blaze-emc.dtsi
index 2ce1b12be44d..e8dcc4f51fc5 100644
--- a/arch/arm/boot/dts/tegra124-nyan-blaze-emc.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra124-nyan-blaze-emc.dtsi
@@ -1,4 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
+
+#include <dt-bindings/clock/tegra124-car.h>
+
 / {
 	clock@60006000 {
 		emc-timings-1 {
@@ -2055,14 +2058,14 @@
 			};
 		};
 	};
-};
 
-&emc_icc_dvfs_opp_table {
-	/delete-node/ opp-924000000-1100;
-	/delete-node/ opp-1200000000-1100;
-};
+	opp-table-actmon {
+		/delete-node/ opp-924000000;
+		/delete-node/ opp-1200000000;
+	};
 
-&emc_bw_dfs_opp_table {
-	/delete-node/ opp-924000000;
-	/delete-node/ opp-1200000000;
+	opp-table-emc {
+		/delete-node/ opp-924000000-1100;
+		/delete-node/ opp-1200000000-1100;
+	};
 };
diff --git a/arch/arm/boot/dts/tegra124-nyan-blaze.dts b/arch/arm/boot/dts/nvidia/tegra124-nyan-blaze.dts
index abdf4456826f..432540c10065 100644
--- a/arch/arm/boot/dts/tegra124-nyan-blaze.dts
+++ b/arch/arm/boot/dts/nvidia/tegra124-nyan-blaze.dts
@@ -20,24 +20,18 @@
 			aux-bus {
 				panel: panel {
 					compatible = "samsung,ltn140at29-301";
+					power-supply = <&vdd_3v3_panel>;
 					backlight = <&backlight>;
 				};
 			};
 		};
 	};
 
-	sound {
-		compatible = "nvidia,tegra-audio-max98090-nyan-blaze",
-			     "nvidia,tegra-audio-max98090-nyan",
-			     "nvidia,tegra-audio-max98090";
-		nvidia,model = "GoogleNyanBlaze";
-	};
-
 	pinmux@70000868 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinmux_default>;
 
-		pinmux_default: common {
+		pinmux_default: pinmux {
 			clk_32k_out_pa0 {
 				nvidia,pins = "clk_32k_out_pa0";
 				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
@@ -1342,4 +1336,11 @@
 			};
 		};
 	};
+
+	sound {
+		compatible = "nvidia,tegra-audio-max98090-nyan-blaze",
+			     "nvidia,tegra-audio-max98090-nyan",
+			     "nvidia,tegra-audio-max98090";
+		nvidia,model = "GoogleNyanBlaze";
+	};
 };
diff --git a/arch/arm/boot/dts/tegra124-nyan.dtsi b/arch/arm/boot/dts/nvidia/tegra124-nyan.dtsi
index a93cfb492ba1..974c76f007db 100644
--- a/arch/arm/boot/dts/tegra124-nyan.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra124-nyan.dtsi
@@ -70,6 +70,8 @@
 
 	serial@70006000 {
 		/* Debug connector on the bottom of the board near SD card. */
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -336,6 +338,7 @@
 			interrupt-parent = <&gpio>;
 			interrupts = <TEGRA_GPIO(C, 7) IRQ_TYPE_LEVEL_LOW>;
 			reg = <0>;
+			wakeup-source;
 
 			google,cros-ec-spi-msg-delay = <2000>;
 
@@ -498,12 +501,6 @@
 		};
 	};
 
-	sdhci0_pwrseq: sdhci0_pwrseq {
-		compatible = "mmc-pwrseq-simple";
-
-		reset-gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_LOW>;
-	};
-
 	mmc@700b0000 { /* WiFi/BT on this bus */
 		status = "okay";
 		bus-width = <4>;
@@ -595,15 +592,36 @@
 	};
 
 	cpus {
-		cpu@0 {
+		cpu0: cpu@0 {
+			#cooling-cells = <2>;
 			vdd-cpu-supply = <&vdd_cpu>;
 		};
+
+		cpu1: cpu@1 {
+			#cooling-cells = <2>;
+		};
+
+		cpu2: cpu@2 {
+			#cooling-cells = <2>;
+		};
+
+		cpu3: cpu@3 {
+			#cooling-cells = <2>;
+		};
 	};
 
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		lid {
+		key-power {
+			label = "Power";
+			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			debounce-interval = <30>;
+			wakeup-source;
+		};
+
+		switch-lid {
 			label = "Lid";
 			gpios = <&gpio TEGRA_GPIO(R, 4) GPIO_ACTIVE_LOW>;
 			linux,input-type = <5>;
@@ -611,14 +629,18 @@
 			debounce-interval = <1>;
 			wakeup-source;
 		};
+	};
 
-		power {
-			label = "Power";
-			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_POWER>;
-			debounce-interval = <30>;
-			wakeup-source;
-		};
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
+		priority = <200>;
+	};
+
+	sdhci0_pwrseq: pwrseq-sdhci0 {
+		compatible = "mmc-pwrseq-simple";
+
+		reset-gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_LOW>;
 	};
 
 	vdd_mux: regulator-mux {
@@ -694,6 +716,7 @@
 		regulator-name = "+5V_USB_HS";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
 		gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 		gpio-open-drain;
@@ -705,6 +728,7 @@
 		regulator-name = "+5V_USB_SS";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
 		gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 		gpio-open-drain;
@@ -785,30 +809,6 @@
 				<&gpio TEGRA_GPIO(R, 7) GPIO_ACTIVE_HIGH>;
 	};
 
-	gpio-restart {
-		compatible = "gpio-restart";
-		gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
-		priority = <200>;
-	};
-
-	cpus {
-		cpu0: cpu@0 {
-			#cooling-cells = <2>;
-		};
-
-		cpu1: cpu@1 {
-			#cooling-cells = <2>;
-		};
-
-		cpu2: cpu@2 {
-			#cooling-cells = <2>;
-		};
-
-		cpu3: cpu@3 {
-			#cooling-cells = <2>;
-		};
-	};
-
 	thermal-zones {
 		cpu-skin-thermal {
 			polling-delay-passive = <1000>; /* milliseconds */
@@ -838,4 +838,4 @@
 	};
 };
 
-#include "cros-ec-keyboard.dtsi"
+#include "../cros-ec-keyboard.dtsi"
diff --git a/arch/arm/boot/dts/tegra124-peripherals-opp.dtsi b/arch/arm/boot/dts/nvidia/tegra124-peripherals-opp.dtsi
index b262c1289da5..b262c1289da5 100644
--- a/arch/arm/boot/dts/tegra124-peripherals-opp.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra124-peripherals-opp.dtsi
diff --git a/arch/arm/boot/dts/tegra124-venice2.dts b/arch/arm/boot/dts/nvidia/tegra124-venice2.dts
index 6a9592ceb5f2..df98dc2a67b8 100644
--- a/arch/arm/boot/dts/tegra124-venice2.dts
+++ b/arch/arm/boot/dts/nvidia/tegra124-venice2.dts
@@ -52,6 +52,7 @@
 			aux-bus {
 				panel: panel {
 					compatible = "lg,lp129qe";
+					power-supply = <&vdd_3v3_panel>;
 					backlight = <&backlight>;
 				};
 			};
@@ -70,7 +71,7 @@
 		pinctrl-names = "boot";
 		pinctrl-0 = <&pinmux_boot>;
 
-		pinmux_boot: common {
+		pinmux_boot: pinmux {
 			dap_mclk1_pw4 {
 				nvidia,pins = "dap_mclk1_pw4";
 				nvidia,function = "extperiph1";
@@ -608,6 +609,8 @@
 	};
 
 	serial@70006000 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -854,6 +857,7 @@
 			interrupt-parent = <&gpio>;
 			interrupts = <TEGRA_GPIO(C, 7) IRQ_TYPE_LEVEL_LOW>;
 			reg = <0>;
+			wakeup-source;
 
 			google,cros-ec-spi-msg-delay = <2000>;
 
@@ -1078,7 +1082,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -1252,4 +1256,4 @@
 	};
 };
 
-#include "cros-ec-keyboard.dtsi"
+#include "../cros-ec-keyboard.dtsi"
diff --git a/arch/arm/boot/dts/tegra124.dtsi b/arch/arm/boot/dts/nvidia/tegra124.dtsi
index a9ab548781e1..ec4f0e346b2b 100644
--- a/arch/arm/boot/dts/tegra124.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra124.dtsi
@@ -165,6 +165,22 @@
 			status = "disabled";
 		};
 
+		dsia: dsi@54300000 {
+			compatible = "nvidia,tegra124-dsi";
+			reg = <0x0 0x54300000 0x0 0x00040000>;
+			clocks = <&tegra_car TEGRA124_CLK_DSIA>,
+				 <&tegra_car TEGRA124_CLK_DSIALP>,
+				 <&tegra_car TEGRA124_CLK_PLL_D_OUT0>;
+			clock-names = "dsi", "lp", "parent";
+			resets = <&tegra_car 48>;
+			reset-names = "dsi";
+			nvidia,mipi-calibrate = <&mipi 0x060>; /* DSIA & DSIB pads */
+			status = "disabled";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
 		vic@54340000 {
 			compatible = "nvidia,tegra124-vic";
 			reg = <0x0 0x54340000 0x0 0x00040000>;
@@ -177,6 +193,22 @@
 			iommus = <&mc TEGRA_SWGROUP_VIC>;
 		};
 
+		dsib: dsi@54400000 {
+			compatible = "nvidia,tegra124-dsi";
+			reg = <0x0 0x54400000 0x0 0x00040000>;
+			clocks = <&tegra_car TEGRA124_CLK_DSIB>,
+				 <&tegra_car TEGRA124_CLK_DSIBLP>,
+				 <&tegra_car TEGRA124_CLK_PLL_D_OUT0>;
+			clock-names = "dsi", "lp", "parent";
+			resets = <&tegra_car 82>;
+			reset-names = "dsi";
+			nvidia,mipi-calibrate = <&mipi 0x180>; /* DSIC & DSID pads */
+			status = "disabled";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
 		sor@54540000 {
 			compatible = "nvidia,tegra124-sor";
 			reg = <0x0 0x54540000 0x0 0x00040000>;
@@ -380,7 +412,6 @@
 		interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA124_CLK_UARTA>;
 		resets = <&tegra_car 6>;
-		reset-names = "serial";
 		dmas = <&apbdma 8>, <&apbdma 8>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -393,7 +424,6 @@
 		interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA124_CLK_UARTB>;
 		resets = <&tegra_car 7>;
-		reset-names = "serial";
 		dmas = <&apbdma 9>, <&apbdma 9>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -406,7 +436,6 @@
 		interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA124_CLK_UARTC>;
 		resets = <&tegra_car 55>;
-		reset-names = "serial";
 		dmas = <&apbdma 10>, <&apbdma 10>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -419,7 +448,6 @@
 		interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA124_CLK_UARTD>;
 		resets = <&tegra_car 65>;
-		reset-names = "serial";
 		dmas = <&apbdma 19>, <&apbdma 19>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -639,6 +667,16 @@
 		reset-names = "fuse";
 	};
 
+	cec@70015000 {
+		compatible = "nvidia,tegra124-cec";
+		reg = <0x0 0x70015000 0x0 0x00001000>;
+		interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&tegra_car TEGRA124_CLK_CEC>;
+		clock-names = "cec";
+		status = "disabled";
+		hdmi-phandle = <&hdmi>;
+	};
+
 	mc: memory-controller@70019000 {
 		compatible = "nvidia,tegra124-mc";
 		reg = <0x0 0x70019000 0x0 0x1000>;
@@ -906,16 +944,6 @@
 		status = "disabled";
 	};
 
-	cec@70015000 {
-		compatible = "nvidia,tegra124-cec";
-		reg = <0x0 0x70015000 0x0 0x00001000>;
-		interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&tegra_car TEGRA124_CLK_CEC>;
-		clock-names = "cec";
-		status = "disabled";
-		hdmi-phandle = <&hdmi>;
-	};
-
 	soctherm: thermal-sensor@700e2000 {
 		compatible = "nvidia,tegra124-soctherm";
 		reg = <0x0 0x700e2000 0x0 0x600>, /* SOC_THERM reg_base */
@@ -942,6 +970,14 @@
 		};
 	};
 
+	mipi: mipi@700e3000 {
+		compatible = "nvidia,tegra124-mipi";
+		reg = <0x0 0x700e3000 0x0 0x100>;
+		clocks = <&tegra_car TEGRA124_CLK_MIPI_CAL>;
+		clock-names = "mipi-cal";
+		#nvidia,mipi-calibrate-cells = <1>;
+	};
+
 	dfll: clock@70110000 {
 		compatible = "nvidia,tegra124-dfll";
 		reg = <0 0x70110000 0 0x100>, /* DFLL control */
diff --git a/arch/arm/boot/dts/tegra20-acer-a500-picasso.dts b/arch/arm/boot/dts/nvidia/tegra20-acer-a500-picasso.dts
index a170a4ba36c1..a619ea83ed3b 100644
--- a/arch/arm/boot/dts/tegra20-acer-a500-picasso.dts
+++ b/arch/arm/boot/dts/nvidia/tegra20-acer-a500-picasso.dts
@@ -65,7 +65,7 @@
 			rgb {
 				status = "okay";
 
-				port@0 {
+				port {
 					lcd_output: endpoint {
 						remote-endpoint = <&lvds_encoder_input>;
 						bus-width = <18>;
@@ -342,36 +342,39 @@
 			};
 		};
 
-		state_i2cmux_ddc: pinmux_i2cmux_ddc {
+		state_i2cmux_ddc: pinmux-i2cmux-ddc {
 			ddc {
 				nvidia,pins = "ddc";
 				nvidia,function = "i2c2";
 			};
+
 			pta {
 				nvidia,pins = "pta";
 				nvidia,function = "rsvd4";
 			};
 		};
 
-		state_i2cmux_pta: pinmux_i2cmux_pta {
+		state_i2cmux_idle: pinmux-i2cmux-idle {
 			ddc {
 				nvidia,pins = "ddc";
 				nvidia,function = "rsvd4";
 			};
+
 			pta {
 				nvidia,pins = "pta";
-				nvidia,function = "i2c2";
+				nvidia,function = "rsvd4";
 			};
 		};
 
-		state_i2cmux_idle: pinmux_i2cmux_idle {
+		state_i2cmux_pta: pinmux-i2cmux-pta {
 			ddc {
 				nvidia,pins = "ddc";
 				nvidia,function = "rsvd4";
 			};
+
 			pta {
 				nvidia,pins = "pta";
-				nvidia,function = "rsvd4";
+				nvidia,function = "i2c2";
 			};
 		};
 	};
@@ -390,12 +393,14 @@
 
 	uartb: serial@70006040 {
 		compatible = "nvidia,tegra20-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 		/* GPS BCM4751 */
 	};
 
 	uartc: serial@70006200 {
 		compatible = "nvidia,tegra20-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 		status = "okay";
 
@@ -417,7 +422,7 @@
 			vddio-supply = <&vdd_1v8_sys>;
 
 			device-wakeup-gpios = <&gpio TEGRA_GPIO(U, 1) GPIO_ACTIVE_HIGH>;
-			shutdown-gpios =      <&gpio TEGRA_GPIO(U, 0) GPIO_ACTIVE_HIGH>;
+			shutdown-gpios = <&gpio TEGRA_GPIO(U, 0) GPIO_ACTIVE_HIGH>;
 		};
 	};
 
@@ -425,6 +430,10 @@
 		/* Docking station */
 	};
 
+	pwm: pwm@7000a000 {
+		status = "okay";
+	};
+
 	i2c@7000c000 {
 		clock-frequency = <400000>;
 		status = "okay";
@@ -512,45 +521,6 @@
 		status = "okay";
 	};
 
-	i2cmux {
-		compatible = "i2c-mux-pinctrl";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		i2c-parent = <&{/i2c@7000c400}>;
-
-		pinctrl-names = "ddc", "pta", "idle";
-		pinctrl-0 = <&state_i2cmux_ddc>;
-		pinctrl-1 = <&state_i2cmux_pta>;
-		pinctrl-2 = <&state_i2cmux_idle>;
-
-		hdmi_ddc: i2c@0 {
-			reg = <0>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		panel_ddc: i2c@1 {
-			reg = <1>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			embedded-controller@58 {
-				compatible = "acer,a500-iconia-ec", "ene,kb930";
-				reg = <0x58>;
-
-				system-power-controller;
-
-				monitored-battery = <&bat1010>;
-				power-supplies = <&mains>;
-			};
-		};
-	};
-
-	pwm: pwm@7000a000 {
-		status = "okay";
-	};
-
 	i2c@7000d000 {
 		clock-frequency = <100000>;
 		status = "okay";
@@ -729,396 +699,6 @@
 		core-supply = <&vdd_core>;
 	};
 
-	usb@c5000000 {
-		compatible = "nvidia,tegra20-udc";
-		status = "okay";
-		dr_mode = "peripheral";
-	};
-
-	usb-phy@c5000000 {
-		status = "okay";
-		dr_mode = "peripheral";
-		nvidia,xcvr-setup-use-fuses;
-		nvidia,xcvr-lsfslew = <2>;
-		nvidia,xcvr-lsrslew = <2>;
-	};
-
-	usb@c5008000 {
-		status = "okay";
-	};
-
-	usb-phy@c5008000 {
-		status = "okay";
-		nvidia,xcvr-setup-use-fuses;
-		nvidia,xcvr-lsfslew = <2>;
-		nvidia,xcvr-lsrslew = <2>;
-		vbus-supply = <&vdd_5v0_sys>;
-	};
-
-	brcm_wifi_pwrseq: wifi-pwrseq {
-		compatible = "mmc-pwrseq-simple";
-
-		clocks = <&rtc_32k_wifi>;
-		clock-names = "ext_clock";
-
-		reset-gpios = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_LOW>;
-		post-power-on-delay-ms = <300>;
-		power-off-delay-us = <300>;
-	};
-
-	sdmmc1: mmc@c8000000 {
-		status = "okay";
-
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		assigned-clocks = <&tegra_car TEGRA20_CLK_SDMMC1>;
-		assigned-clock-parents = <&tegra_car TEGRA20_CLK_PLL_C>;
-		assigned-clock-rates = <50000000>;
-
-		max-frequency = <50000000>;
-		keep-power-in-suspend;
-		bus-width = <4>;
-		non-removable;
-
-		mmc-pwrseq = <&brcm_wifi_pwrseq>;
-		vmmc-supply = <&vdd_3v3_sys>;
-		vqmmc-supply = <&vdd_1v8_sys>;
-
-		/* Azurewave AW-NH611 BCM4329 */
-		wifi@1 {
-			reg = <1>;
-			compatible = "brcm,bcm4329-fmac";
-			interrupt-parent = <&gpio>;
-			interrupts = <TEGRA_GPIO(S, 0) IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "host-wake";
-		};
-	};
-
-	sdmmc3: mmc@c8000400 {
-		status = "okay";
-		bus-width = <4>;
-		cd-gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
-		power-gpios = <&gpio TEGRA_GPIO(I, 6) GPIO_ACTIVE_HIGH>;
-		vmmc-supply = <&vdd_3v3_sys>;
-		vqmmc-supply = <&vdd_3v3_sys>;
-	};
-
-	sdmmc4: mmc@c8000600 {
-		status = "okay";
-		bus-width = <8>;
-		vmmc-supply = <&vcore_emmc>;
-		vqmmc-supply = <&vdd_3v3_sys>;
-		non-removable;
-	};
-
-	mains: ac-adapter-detect {
-		compatible = "gpio-charger";
-		charger-type = "mains";
-		gpios = <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_LOW>;
-	};
-
-	backlight: backlight {
-		compatible = "pwm-backlight";
-
-		enable-gpios = <&gpio TEGRA_GPIO(D, 4) GPIO_ACTIVE_HIGH>;
-		power-supply = <&vdd_3v3_sys>;
-		pwms = <&pwm 2 41667>;
-
-		brightness-levels = <7 255>;
-		num-interpolated-steps = <248>;
-		default-brightness-level = <20>;
-	};
-
-	bat1010: battery-2s1p {
-		compatible = "simple-battery";
-		charge-full-design-microamp-hours = <3260000>;
-		energy-full-design-microwatt-hours = <24000000>;
-		operating-range-celsius = <0 40>;
-	};
-
-	/* PMIC has a built-in 32KHz oscillator which is used by PMC */
-	clk32k_in: clock-32k-in {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <32768>;
-		clock-output-names = "tps658621-out32k";
-	};
-
-	/*
-	 * This standalone onboard fixed-clock always-ON 32KHz
-	 * oscillator is used as a reference clock-source by the
-	 * Azurewave WiFi/BT module.
-	 */
-	rtc_32k_wifi: clock-32k-wifi {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <32768>;
-		clock-output-names = "kk3270032";
-	};
-
-	cpus {
-		cpu0: cpu@0 {
-			cpu-supply = <&vdd_cpu>;
-			operating-points-v2 = <&cpu0_opp_table>;
-			#cooling-cells = <2>;
-		};
-
-		cpu1: cpu@1 {
-			cpu-supply = <&vdd_cpu>;
-			operating-points-v2 = <&cpu0_opp_table>;
-			#cooling-cells = <2>;
-		};
-	};
-
-	display-panel {
-		compatible = "auo,b101ew05", "panel-lvds";
-
-		ddc-i2c-bus = <&panel_ddc>;
-		power-supply = <&vdd_pnl>;
-		backlight = <&backlight>;
-
-		width-mm = <218>;
-		height-mm = <135>;
-
-		data-mapping = "jeida-18";
-
-		panel-timing {
-			clock-frequency = <71200000>;
-			hactive = <1280>;
-			vactive = <800>;
-			hfront-porch = <8>;
-			hback-porch = <18>;
-			hsync-len = <184>;
-			vsync-len = <3>;
-			vfront-porch = <4>;
-			vback-porch = <8>;
-		};
-
-		port {
-			panel_input: endpoint {
-				remote-endpoint = <&lvds_encoder_output>;
-			};
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		power {
-			label = "Power";
-			gpios = <&gpio TEGRA_GPIO(I, 3) GPIO_ACTIVE_HIGH>;
-			linux,code = <KEY_POWER>;
-			debounce-interval = <10>;
-			wakeup-event-action = <EV_ACT_ASSERTED>;
-			wakeup-source;
-		};
-
-		rotation-lock {
-			label = "Rotate-lock";
-			gpios = <&gpio TEGRA_GPIO(Q, 2) GPIO_ACTIVE_HIGH>;
-			linux,code = <SW_ROTATE_LOCK>;
-			linux,input-type = <EV_SW>;
-			debounce-interval = <10>;
-		};
-
-		volume-up {
-			label = "Volume Up";
-			gpios = <&gpio TEGRA_GPIO(Q, 4) GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEUP>;
-			debounce-interval = <10>;
-			wakeup-event-action = <EV_ACT_ASSERTED>;
-			wakeup-source;
-		};
-
-		volume-down {
-			label = "Volume Down";
-			gpios = <&gpio TEGRA_GPIO(Q, 5) GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEDOWN>;
-			debounce-interval = <10>;
-			wakeup-event-action = <EV_ACT_ASSERTED>;
-			wakeup-source;
-		};
-	};
-
-	haptic-feedback {
-		compatible = "gpio-vibrator";
-		enable-gpios = <&gpio TEGRA_GPIO(V, 5) GPIO_ACTIVE_HIGH>;
-		vcc-supply = <&vdd_3v3_sys>;
-	};
-
-	lvds-encoder {
-		compatible = "ti,sn75lvds83", "lvds-encoder";
-
-		powerdown-gpios = <&gpio TEGRA_GPIO(B, 2) GPIO_ACTIVE_LOW>;
-		power-supply = <&vdd_3v3_sys>;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-
-				lvds_encoder_input: endpoint {
-					remote-endpoint = <&lcd_output>;
-				};
-			};
-
-			port@1 {
-				reg = <1>;
-
-				lvds_encoder_output: endpoint {
-					remote-endpoint = <&panel_input>;
-				};
-			};
-		};
-	};
-
-	vdd_5v0_sys: regulator-5v0 {
-		compatible = "regulator-fixed";
-		regulator-name = "vdd_5v0";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		regulator-always-on;
-	};
-
-	vdd_3v3_sys: regulator-3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "vdd_3v3_vs";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-		vin-supply = <&vdd_5v0_sys>;
-	};
-
-	vdd_1v8_sys: regulator-1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "vdd_1v8_vs";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		regulator-always-on;
-		vin-supply = <&vdd_5v0_sys>;
-	};
-
-	vdd_pnl: regulator-panel {
-		compatible = "regulator-fixed";
-		regulator-name = "vdd_panel";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-enable-ramp-delay = <300000>;
-		gpio = <&gpio TEGRA_GPIO(C, 6) GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-		vin-supply = <&vdd_5v0_sys>;
-	};
-
-	sound {
-		compatible = "nvidia,tegra-audio-wm8903-picasso",
-			     "nvidia,tegra-audio-wm8903";
-		nvidia,model = "Acer Iconia Tab A500 WM8903";
-
-		nvidia,audio-routing =
-			"Headphone Jack", "HPOUTR",
-			"Headphone Jack", "HPOUTL",
-			"Int Spk", "LINEOUTL",
-			"Int Spk", "LINEOUTR",
-			"Mic Jack", "MICBIAS",
-			"IN2L", "Mic Jack",
-			"IN2R", "Mic Jack",
-			"IN1L", "Int Mic",
-			"IN1R", "Int Mic";
-
-		nvidia,i2s-controller = <&tegra_i2s1>;
-		nvidia,audio-codec = <&wm8903>;
-
-		nvidia,spkr-en-gpios = <&wm8903 2 GPIO_ACTIVE_HIGH>;
-		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_LOW>;
-		nvidia,int-mic-en-gpios = <&wm8903 1 GPIO_ACTIVE_HIGH>;
-		nvidia,headset;
-
-		clocks = <&tegra_car TEGRA20_CLK_PLL_A>,
-			 <&tegra_car TEGRA20_CLK_PLL_A_OUT0>,
-			 <&tegra_car TEGRA20_CLK_CDEV1>;
-		clock-names = "pll_a", "pll_a_out0", "mclk";
-	};
-
-	thermal-zones {
-		/*
-		 * NCT1008 has two sensors:
-		 *
-		 *	0: internal that monitors ambient/skin temperature
-		 *	1: external that is connected to the CPU's diode
-		 *
-		 * Ideally we should use userspace thermal governor,
-		 * but it's a much more complex solution.  The "skin"
-		 * zone is a simpler solution which prevents A500 from
-		 * getting too hot from a user's tactile perspective.
-		 * The CPU zone is intended to protect silicon from damage.
-		 */
-
-		skin-thermal {
-			polling-delay-passive = <1000>; /* milliseconds */
-			polling-delay = <5000>; /* milliseconds */
-
-			thermal-sensors = <&nct1008 0>;
-
-			trips {
-				trip0: skin-alert {
-					/* start throttling at 60C */
-					temperature = <60000>;
-					hysteresis = <200>;
-					type = "passive";
-				};
-
-				trip1: skin-crit {
-					/* shut down at 70C */
-					temperature = <70000>;
-					hysteresis = <2000>;
-					type = "critical";
-				};
-			};
-
-			cooling-maps {
-				map0 {
-					trip = <&trip0>;
-					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-				};
-			};
-		};
-
-		cpu-thermal {
-			polling-delay-passive = <1000>; /* milliseconds */
-			polling-delay = <5000>; /* milliseconds */
-
-			thermal-sensors = <&nct1008 1>;
-
-			trips {
-				trip2: cpu-alert {
-					/* throttle at 85C until temperature drops to 84.8C */
-					temperature = <85000>;
-					hysteresis = <200>;
-					type = "passive";
-				};
-
-				trip3: cpu-crit {
-					/* shut down at 90C */
-					temperature = <90000>;
-					hysteresis = <2000>;
-					type = "critical";
-				};
-			};
-
-			cooling-maps {
-				map1 {
-					trip = <&trip2>;
-					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-				};
-			};
-		};
-	};
-
 	memory-controller@7000f400 {
 		nvidia,use-ram-code;
 
@@ -1514,9 +1094,434 @@
 			};
 		};
 	};
-};
 
-&emc_icc_dvfs_opp_table {
-	/delete-node/ opp-666000000;
-	/delete-node/ opp-760000000;
+	usb@c5000000 {
+		compatible = "nvidia,tegra20-udc";
+		status = "okay";
+		dr_mode = "peripheral";
+	};
+
+	usb-phy@c5000000 {
+		status = "okay";
+		dr_mode = "peripheral";
+		nvidia,xcvr-setup-use-fuses;
+		nvidia,xcvr-lsfslew = <2>;
+		nvidia,xcvr-lsrslew = <2>;
+	};
+
+	usb@c5008000 {
+		status = "okay";
+	};
+
+	usb-phy@c5008000 {
+		status = "okay";
+		nvidia,xcvr-setup-use-fuses;
+		nvidia,xcvr-lsfslew = <2>;
+		nvidia,xcvr-lsrslew = <2>;
+		vbus-supply = <&vdd_5v0_sys>;
+	};
+
+	sdmmc1: mmc@c8000000 {
+		status = "okay";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		assigned-clocks = <&tegra_car TEGRA20_CLK_SDMMC1>;
+		assigned-clock-parents = <&tegra_car TEGRA20_CLK_PLL_C>;
+		assigned-clock-rates = <50000000>;
+
+		max-frequency = <50000000>;
+		keep-power-in-suspend;
+		bus-width = <4>;
+		non-removable;
+
+		mmc-pwrseq = <&brcm_wifi_pwrseq>;
+		vmmc-supply = <&vdd_3v3_sys>;
+		vqmmc-supply = <&vdd_1v8_sys>;
+
+		/* Azurewave AW-NH611 BCM4329 */
+		wifi@1 {
+			reg = <1>;
+			compatible = "brcm,bcm4329-fmac";
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(S, 0) IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "host-wake";
+		};
+	};
+
+	sdmmc3: mmc@c8000400 {
+		status = "okay";
+		bus-width = <4>;
+		cd-gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
+		power-gpios = <&gpio TEGRA_GPIO(I, 6) GPIO_ACTIVE_HIGH>;
+		vmmc-supply = <&vdd_3v3_sys>;
+		vqmmc-supply = <&vdd_3v3_sys>;
+	};
+
+	sdmmc4: mmc@c8000600 {
+		status = "okay";
+		bus-width = <8>;
+		vmmc-supply = <&vcore_emmc>;
+		vqmmc-supply = <&vdd_3v3_sys>;
+		non-removable;
+	};
+
+	mains: ac-adapter-detect {
+		compatible = "gpio-charger";
+		charger-type = "mains";
+		gpios = <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_LOW>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+
+		enable-gpios = <&gpio TEGRA_GPIO(D, 4) GPIO_ACTIVE_HIGH>;
+		power-supply = <&vdd_3v3_sys>;
+		pwms = <&pwm 2 41667>;
+
+		brightness-levels = <7 255>;
+		num-interpolated-steps = <248>;
+		default-brightness-level = <20>;
+	};
+
+	bat1010: battery-2s1p {
+		compatible = "simple-battery";
+		charge-full-design-microamp-hours = <3260000>;
+		energy-full-design-microwatt-hours = <24000000>;
+		operating-range-celsius = <0 40>;
+	};
+
+	/* PMIC has a built-in 32KHz oscillator which is used by PMC */
+	clk32k_in: clock-32k-in {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "tps658621-out32k";
+	};
+
+	/*
+	 * This standalone onboard fixed-clock always-ON 32KHz
+	 * oscillator is used as a reference clock-source by the
+	 * Azurewave WiFi/BT module.
+	 */
+	rtc_32k_wifi: clock-32k-wifi {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "kk3270032";
+	};
+
+	cpus {
+		cpu0: cpu@0 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+
+		cpu1: cpu@1 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+	};
+
+	display-panel {
+		compatible = "auo,b101ew05", "panel-lvds";
+
+		ddc-i2c-bus = <&panel_ddc>;
+		power-supply = <&vdd_pnl>;
+		backlight = <&backlight>;
+
+		width-mm = <218>;
+		height-mm = <135>;
+
+		data-mapping = "jeida-18";
+
+		panel-timing {
+			clock-frequency = <71200000>;
+			hactive = <1280>;
+			vactive = <800>;
+			hfront-porch = <8>;
+			hback-porch = <18>;
+			hsync-len = <184>;
+			vsync-len = <3>;
+			vfront-porch = <4>;
+			vback-porch = <8>;
+		};
+
+		port {
+			panel_input: endpoint {
+				remote-endpoint = <&lvds_encoder_output>;
+			};
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-power {
+			label = "Power";
+			gpios = <&gpio TEGRA_GPIO(I, 3) GPIO_ACTIVE_HIGH>;
+			linux,code = <KEY_POWER>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-rotation-lock {
+			label = "Rotate-lock";
+			gpios = <&gpio TEGRA_GPIO(Q, 2) GPIO_ACTIVE_HIGH>;
+			linux,code = <SW_ROTATE_LOCK>;
+			linux,input-type = <EV_SW>;
+			debounce-interval = <10>;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio TEGRA_GPIO(Q, 5) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio TEGRA_GPIO(Q, 4) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+	};
+
+	haptic-feedback {
+		compatible = "gpio-vibrator";
+		enable-gpios = <&gpio TEGRA_GPIO(V, 5) GPIO_ACTIVE_HIGH>;
+		vcc-supply = <&vdd_3v3_sys>;
+	};
+
+	i2cmux {
+		compatible = "i2c-mux-pinctrl";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c-parent = <&{/i2c@7000c400}>;
+
+		pinctrl-names = "ddc", "pta", "idle";
+		pinctrl-0 = <&state_i2cmux_ddc>;
+		pinctrl-1 = <&state_i2cmux_pta>;
+		pinctrl-2 = <&state_i2cmux_idle>;
+
+		hdmi_ddc: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		panel_ddc: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			embedded-controller@58 {
+				compatible = "acer,a500-iconia-ec", "ene,kb930";
+				reg = <0x58>;
+
+				system-power-controller;
+
+				monitored-battery = <&bat1010>;
+				power-supplies = <&mains>;
+			};
+		};
+	};
+
+	lvds-encoder {
+		compatible = "ti,sn75lvds83", "lvds-encoder";
+
+		powerdown-gpios = <&gpio TEGRA_GPIO(B, 2) GPIO_ACTIVE_LOW>;
+		power-supply = <&vdd_3v3_sys>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lvds_encoder_input: endpoint {
+					remote-endpoint = <&lcd_output>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				lvds_encoder_output: endpoint {
+					remote-endpoint = <&panel_input>;
+				};
+			};
+		};
+	};
+
+	opp-table-emc {
+		/delete-node/ opp-666000000;
+		/delete-node/ opp-760000000;
+	};
+
+	vdd_5v0_sys: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	vdd_3v3_sys: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3_vs";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		vin-supply = <&vdd_5v0_sys>;
+	};
+
+	vdd_1v8_sys: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_1v8_vs";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		vin-supply = <&vdd_5v0_sys>;
+	};
+
+	vdd_pnl: regulator-panel {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_panel";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-enable-ramp-delay = <300000>;
+		gpio = <&gpio TEGRA_GPIO(C, 6) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_sys>;
+	};
+
+	sound {
+		compatible = "nvidia,tegra-audio-wm8903-picasso",
+			     "nvidia,tegra-audio-wm8903";
+		nvidia,model = "Acer Iconia Tab A500 WM8903";
+
+		nvidia,audio-routing =
+			"Headphone Jack", "HPOUTR",
+			"Headphone Jack", "HPOUTL",
+			"Int Spk", "LINEOUTL",
+			"Int Spk", "LINEOUTR",
+			"Mic Jack", "MICBIAS",
+			"IN2L", "Mic Jack",
+			"IN2R", "Mic Jack",
+			"IN1L", "Int Mic",
+			"IN1R", "Int Mic";
+
+		nvidia,i2s-controller = <&tegra_i2s1>;
+		nvidia,audio-codec = <&wm8903>;
+
+		nvidia,spkr-en-gpios = <&wm8903 2 GPIO_ACTIVE_HIGH>;
+		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_LOW>;
+		nvidia,int-mic-en-gpios = <&wm8903 1 GPIO_ACTIVE_HIGH>;
+		nvidia,headset;
+
+		clocks = <&tegra_car TEGRA20_CLK_PLL_A>,
+			 <&tegra_car TEGRA20_CLK_PLL_A_OUT0>,
+			 <&tegra_car TEGRA20_CLK_CDEV1>;
+		clock-names = "pll_a", "pll_a_out0", "mclk";
+	};
+
+	thermal-zones {
+		/*
+		 * NCT1008 has two sensors:
+		 *
+		 *	0: internal that monitors ambient/skin temperature
+		 *	1: external that is connected to the CPU's diode
+		 *
+		 * Ideally we should use userspace thermal governor,
+		 * but it's a much more complex solution.  The "skin"
+		 * zone is a simpler solution which prevents A500 from
+		 * getting too hot from a user's tactile perspective.
+		 * The CPU zone is intended to protect silicon from damage.
+		 */
+
+		skin-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct1008 0>;
+
+			trips {
+				trip0: skin-alert {
+					/* start throttling at 60C */
+					temperature = <60000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip1: skin-crit {
+					/* shut down at 70C */
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&trip0>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		cpu-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct1008 1>;
+
+			trips {
+				trip2: cpu-alert {
+					/* throttle at 85C until temperature drops to 84.8C */
+					temperature = <85000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip3: cpu-crit {
+					/* shut down at 90C */
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map1 {
+					trip = <&trip2>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
+	brcm_wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+
+		clocks = <&rtc_32k_wifi>;
+		clock-names = "ext_clock";
+
+		reset-gpios = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <300>;
+		power-off-delay-us = <300>;
+	};
 };
diff --git a/arch/arm/boot/dts/nvidia/tegra20-asus-sl101.dts b/arch/arm/boot/dts/nvidia/tegra20-asus-sl101.dts
new file mode 100644
index 000000000000..8828129d1fa3
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra20-asus-sl101.dts
@@ -0,0 +1,61 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "tegra20-asus-transformer-common.dtsi"
+
+/ {
+	model = "ASUS Eee Pad Slider SL101";
+	compatible = "asus,sl101", "nvidia,tegra20";
+
+	i2c@7000c000 {
+		magnetometer@e {
+			mount-matrix =  "1",  "0",  "0",
+					"0", "-1",  "0",
+					"0",  "0",  "1";
+		};
+
+		/* Atmel MXT1386 Touchscreen */
+		touchscreen@5a {
+			compatible = "atmel,maxtouch";
+			reg = <0x5a>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(V, 6) IRQ_TYPE_LEVEL_LOW>;
+
+			reset-gpios = <&gpio TEGRA_GPIO(Q, 7) GPIO_ACTIVE_LOW>;
+
+			vdda-supply = <&vdd_3v3_sys>;
+			vdd-supply  = <&vdd_3v3_sys>;
+
+			atmel,wakeup-method = <ATMEL_MXT_WAKEUP_I2C_SCL>;
+		};
+
+		gyroscope@68 {
+			mount-matrix =	 "0",  "1",  "0",
+					"-1",  "0",  "0",
+					 "0",  "0",  "1";
+
+			i2c-gate {
+				accelerometer@f {
+					mount-matrix =	 "1",  "0",  "0",
+							 "0", "-1",  "0",
+							 "0",  "0",  "1";
+				};
+			};
+		};
+	};
+
+	extcon-keys {
+		compatible = "gpio-keys";
+
+		switch-tablet-mode {
+			label = "Tablet Mode";
+			gpios = <&gpio TEGRA_GPIO(S, 4) GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_TABLET_MODE>;
+			debounce-interval = <500>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/nvidia/tegra20-asus-tf101.dts b/arch/arm/boot/dts/nvidia/tegra20-asus-tf101.dts
new file mode 100644
index 000000000000..0d93820a5ad4
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra20-asus-tf101.dts
@@ -0,0 +1,61 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "tegra20-asus-transformer-common.dtsi"
+
+/ {
+	model = "ASUS Eee Pad Transformer TF101";
+	compatible = "asus,tf101", "nvidia,tegra20";
+
+	i2c@7000c000 {
+		magnetometer@e {
+			mount-matrix = "-1",  "0",  "0",
+					"0",  "1",  "0",
+					"0",  "0", "-1";
+		};
+
+		/* Atmel MXT1386 Touchscreen */
+		touchscreen@5b {
+			compatible = "atmel,maxtouch";
+			reg = <0x5b>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(V, 6) IRQ_TYPE_LEVEL_LOW>;
+
+			reset-gpios = <&gpio TEGRA_GPIO(Q, 7) GPIO_ACTIVE_LOW>;
+
+			vdda-supply = <&vdd_3v3_sys>;
+			vdd-supply  = <&vdd_3v3_sys>;
+
+			atmel,wakeup-method = <ATMEL_MXT_WAKEUP_I2C_SCL>;
+		};
+
+		gyroscope@68 {
+			mount-matrix =	 "0",  "1",  "0",
+					"-1",  "0",  "0",
+					 "0",  "0",  "1";
+
+			i2c-gate {
+				accelerometer@f {
+					mount-matrix =	"-1",  "0",  "0",
+							 "0", "-1",  "0",
+							 "0",  "0", "-1";
+				};
+			};
+		};
+	};
+
+	extcon-keys {
+		compatible = "gpio-keys";
+
+		switch-dock-hall-sensor {
+			label = "Lid";
+			gpios = <&gpio TEGRA_GPIO(S, 4) GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			debounce-interval = <500>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/tegra20-asus-tf101.dts b/arch/arm/boot/dts/nvidia/tegra20-asus-transformer-common.dtsi
index a054d39db466..b48f53c00efa 100644
--- a/arch/arm/boot/dts/tegra20-asus-tf101.dts
+++ b/arch/arm/boot/dts/nvidia/tegra20-asus-transformer-common.dtsi
@@ -1,5 +1,4 @@
 // SPDX-License-Identifier: GPL-2.0
-/dts-v1/;
 
 #include <dt-bindings/input/atmel-maxtouch.h>
 #include <dt-bindings/input/gpio-keys.h>
@@ -11,8 +10,6 @@
 #include "tegra20-cpu-opp-microvolt.dtsi"
 
 / {
-	model = "ASUS EeePad Transformer TF101";
-	compatible = "asus,tf101", "nvidia,tegra20";
 	chassis-type = "convertible";
 
 	aliases {
@@ -66,7 +63,7 @@
 			rgb {
 				status = "okay";
 
-				port@0 {
+				port {
 					lcd_output: endpoint {
 						remote-endpoint = <&lvds_encoder_input>;
 						bus-width = <18>;
@@ -295,7 +292,7 @@
 				nvidia,function = "uartc";
 			};
 
-			conf_ata {
+			conf-ata {
 				nvidia,pins = "ata", "atb", "atc", "atd",
 					"cdev1", "cdev2", "dap1", "dap4",
 					"dte", "ddc", "dtf", "gma", "gmc",
@@ -308,7 +305,7 @@
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
 			};
 
-			conf_ate {
+			conf-ate {
 				nvidia,pins = "ate", "dap2", "dap3", "gmb", "gmd",
 					"owc", "spia", "spib", "spic",
 					"spid", "spie", "spig", "slxa";
@@ -316,37 +313,37 @@
 				nvidia,tristate = <TEGRA_PIN_ENABLE>;
 			};
 
-			conf_ck32 {
+			conf-ck32 {
 				nvidia,pins = "ck32", "ddrc", "pmca", "pmcb",
 					"pmcc", "pmcd", "pmce", "xm2c", "xm2d";
 				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
 			};
 
-			conf_crtp {
+			conf-crtp {
 				nvidia,pins = "crtp", "spih";
 				nvidia,pull = <TEGRA_PIN_PULL_UP>;
 				nvidia,tristate = <TEGRA_PIN_ENABLE>;
 			};
 
-			conf_dta {
+			conf-dta {
 				nvidia,pins = "dta", "dtb", "dtc", "dtd";
 				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
 			};
 
-			conf_spif {
+			conf-spif {
 				nvidia,pins = "spif";
 				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
 				nvidia,tristate = <TEGRA_PIN_ENABLE>;
 			};
 
-			conf_hdint {
+			conf-hdint {
 				nvidia,pins = "hdint", "lcsn", "ldc", "lm1",
 					"lpw1", "lsck", "lsda", "lsdi", "lvp0";
 				nvidia,tristate = <TEGRA_PIN_ENABLE>;
 			};
 
-			conf_kbca {
+			conf-kbca {
 				nvidia,pins = "kbca", "kbcb", "kbcc", "kbcd",
 					"kbce", "kbcf", "sdio1", "uaa", "uab",
 					"uca", "ucb";
@@ -354,12 +351,12 @@
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
 			};
 
-			conf_lc {
+			conf-lc {
 				nvidia,pins = "lc", "ls";
 				nvidia,pull = <TEGRA_PIN_PULL_UP>;
 			};
 
-			conf_ld0 {
+			conf-ld0 {
 				nvidia,pins = "ld0", "ld1", "ld2", "ld3", "ld4",
 					"ld5", "ld6", "ld7", "ld8", "ld9",
 					"ld10", "ld11", "ld12", "ld13", "ld14",
@@ -370,13 +367,13 @@
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
 			};
 
-			conf_ld17_0 {
+			conf-ld17-0 {
 				nvidia,pins = "ld17_0", "ld19_18", "ld21_20",
 					"ld23_22";
 				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
 			};
 
-			drive_sdio1 {
+			drive-sdio1 {
 				nvidia,pins = "drive_sdio1", "drive_ddc", "drive_vi1";
 				nvidia,high-speed-mode = <TEGRA_PIN_DISABLE>;
 				nvidia,schmitt = <TEGRA_PIN_ENABLE>;
@@ -387,7 +384,7 @@
 				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
 			};
 
-			drive_csus {
+			drive-csus {
 				nvidia,pins = "drive_csus";
 				nvidia,high-speed-mode = <TEGRA_PIN_DISABLE>;
 				nvidia,schmitt = <TEGRA_PIN_DISABLE>;
@@ -399,7 +396,7 @@
 			};
 		};
 
-		state_i2cmux_ddc: pinmux_i2cmux_ddc {
+		state_i2cmux_ddc: pinmux-i2cmux-ddc {
 			ddc {
 				nvidia,pins = "ddc";
 				nvidia,function = "i2c2";
@@ -411,7 +408,7 @@
 			};
 		};
 
-		state_i2cmux_pta: pinmux_i2cmux_pta {
+		state_i2cmux_idle: pinmux-i2cmux-idle {
 			ddc {
 				nvidia,pins = "ddc";
 				nvidia,function = "rsvd4";
@@ -419,11 +416,11 @@
 
 			pta {
 				nvidia,pins = "pta";
-				nvidia,function = "i2c2";
+				nvidia,function = "rsvd4";
 			};
 		};
 
-		state_i2cmux_idle: pinmux_i2cmux_idle {
+		state_i2cmux_pta: pinmux-i2cmux-pta {
 			ddc {
 				nvidia,pins = "ddc";
 				nvidia,function = "rsvd4";
@@ -431,7 +428,7 @@
 
 			pta {
 				nvidia,pins = "pta";
-				nvidia,function = "rsvd4";
+				nvidia,function = "i2c2";
 			};
 		};
 	};
@@ -450,12 +447,14 @@
 
 	serial@70006040 {
 		compatible = "nvidia,tegra20-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 		/* GPS BCM4751 */
 	};
 
 	serial@70006200 {
 		compatible = "nvidia,tegra20-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 		status = "okay";
 
@@ -477,11 +476,13 @@
 			vddio-supply = <&vdd_1v8_sys>;
 
 			device-wakeup-gpios = <&gpio TEGRA_GPIO(U, 1) GPIO_ACTIVE_HIGH>;
-			shutdown-gpios =      <&gpio TEGRA_GPIO(U, 0) GPIO_ACTIVE_HIGH>;
+			shutdown-gpios = <&gpio TEGRA_GPIO(U, 0) GPIO_ACTIVE_HIGH>;
 		};
 	};
 
 	serial@70006300 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -498,12 +499,11 @@
 			compatible = "asahi-kasei,ak8974";
 			reg = <0xe>;
 
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(N, 5) IRQ_TYPE_EDGE_RISING>;
+
 			avdd-supply = <&vdd_3v3_sys>;
 			dvdd-supply = <&vdd_1v8_sys>;
-
-			mount-matrix = "-1",  "0",  "0",
-					"0",  "1",  "0",
-					"0",  "0", "-1";
 		};
 
 		wm8903: audio-codec@1a {
@@ -511,7 +511,7 @@
 			reg = <0x1a>;
 
 			interrupt-parent = <&gpio>;
-			interrupts = <TEGRA_GPIO(X, 1) IRQ_TYPE_EDGE_BOTH>;
+			interrupts = <TEGRA_GPIO(X, 3) IRQ_TYPE_EDGE_BOTH>;
 
 			gpio-controller;
 			#gpio-cells = <2>;
@@ -520,10 +520,10 @@
 			micdet-delay = <100>;
 
 			gpio-cfg = <
-				0xffffffff /* don't touch */
-				0xffffffff /* don't touch */
+				0x00000600 /* DMIC_LR, output */
+				0x00000680 /* DMIC_DAT, input */
 				0x00000000 /* Speaker-enable GPIO, output, low */
-				0x00000400 /* Mic bias current detect */
+				0xffffffff /* don't touch */
 				0xffffffff /* don't touch */
 			>;
 
@@ -533,22 +533,6 @@
 			DCVDD-supply = <&vdd_1v8_sys>;
 		};
 
-		/* Atmel MXT1386 Touchscreen */
-		touchscreen@5b {
-			compatible = "atmel,maxtouch";
-			reg = <0x5b>;
-
-			interrupt-parent = <&gpio>;
-			interrupts = <TEGRA_GPIO(V, 6) IRQ_TYPE_LEVEL_LOW>;
-
-			reset-gpios = <&gpio TEGRA_GPIO(Q, 7) GPIO_ACTIVE_LOW>;
-
-			vdda-supply = <&vdd_3v3_sys>;
-			vdd-supply  = <&vdd_3v3_sys>;
-
-			atmel,wakeup-method = <ATMEL_MXT_WAKEUP_I2C_SCL>;
-		};
-
 		gyroscope@68 {
 			compatible = "invensense,mpu3050";
 			reg = <0x68>;
@@ -559,10 +543,6 @@
 			vdd-supply    = <&vdd_3v3_sys>;
 			vlogic-supply = <&vdd_1v8_sys>;
 
-			mount-matrix =	 "0",  "1",  "0",
-					"-1",  "0",  "0",
-					 "0",  "0",  "1";
-
 			i2c-gate {
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -576,10 +556,6 @@
 
 					vdd-supply = <&vdd_1v8_sys>;
 					vddio-supply = <&vdd_1v8_sys>;
-
-					mount-matrix =	 "1",  "0",  "0",
-							 "0",  "1",  "0",
-							 "0",  "0",  "1";
 				};
 			};
 		};
@@ -764,13 +740,6 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			lpddr2 {
-				compatible = "elpida,B8132B2PB-6D-F", "jedec,lpddr2-s4";
-				revision-id = <1 0>;
-				density = <2048>;
-				io-width = <16>;
-			};
-
 			emc-table@25000 {
 				reg = <25000>;
 				compatible = "nvidia,tegra20-emc-table";
@@ -860,6 +829,13 @@
 					0x007e0010 0x00000000 0x00000000 0x0000001b
 					0x00000000 0x00000000 0x00000000 0x00000000>;
 			};
+
+			lpddr2 {
+				compatible = "elpida,B8132B2PB-6D-F", "jedec,lpddr2-s4";
+				revision-id = <1 0>;
+				density = <2048>;
+				io-width = <16>;
+			};
 		};
 	};
 
@@ -977,49 +953,8 @@
 		};
 	};
 
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		dock-hall-sensor {
-			label = "Lid";
-			gpios = <&gpio TEGRA_GPIO(S, 4) GPIO_ACTIVE_LOW>;
-			linux,input-type = <EV_SW>;
-			linux,code = <SW_LID>;
-			debounce-interval = <500>;
-			wakeup-event-action = <EV_ACT_ASSERTED>;
-			wakeup-source;
-		};
-
-		power {
-			label = "Power";
-			gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_POWER>;
-			debounce-interval = <10>;
-			wakeup-event-action = <EV_ACT_ASSERTED>;
-			wakeup-source;
-		};
-
-		volume-up {
-			label = "Volume Up";
-			gpios = <&gpio TEGRA_GPIO(Q, 5) GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEUP>;
-			debounce-interval = <10>;
-			wakeup-event-action = <EV_ACT_ASSERTED>;
-			wakeup-source;
-		};
-
-		volume-down {
-			label = "Volume Down";
-			gpios = <&gpio TEGRA_GPIO(Q, 4) GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEDOWN>;
-			debounce-interval = <10>;
-			wakeup-event-action = <EV_ACT_ASSERTED>;
-			wakeup-source;
-		};
-	};
-
 	display-panel {
-		compatible = "panel-lvds";
+		compatible = "auo,b101ew05", "panel-lvds";
 
 		/* AUO B101EW05 using custom timings */
 
@@ -1051,6 +986,37 @@
 		};
 	};
 
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-power {
+			label = "Power";
+			gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio TEGRA_GPIO(Q, 4) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio TEGRA_GPIO(Q, 5) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+	};
+
 	i2cmux {
 		compatible = "i2c-mux-pinctrl";
 		#address-cells = <1>;
@@ -1081,6 +1047,17 @@
 				sbs,poll-retry-count = <10>;
 				power-supplies = <&mains>;
 			};
+
+			/* Dynaimage ambient light sensor */
+			light-sensor@1c {
+				compatible = "dynaimage,al3000a";
+				reg = <0x1c>;
+
+				interrupt-parent = <&gpio>;
+				interrupts = <TEGRA_GPIO(Z, 2) IRQ_TYPE_LEVEL_HIGH>;
+
+				vdd-supply = <&vdd_1v8_sys>;
+			};
 		};
 	};
 
@@ -1112,6 +1089,11 @@
 		};
 	};
 
+	opp-table-emc {
+		/delete-node/ opp-666000000;
+		/delete-node/ opp-760000000;
+	};
+
 	vdd_5v0_sys: regulator-5v0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_5v0";
@@ -1179,15 +1161,16 @@
 			"Int Spk", "RON",
 			"Int Spk", "LOP",
 			"Int Spk", "LON",
-			"Mic Jack", "MICBIAS",
-			"IN1L", "Mic Jack";
+			"IN2L", "Mic Jack",
+			"DMICDAT", "Int Mic";
 
 		nvidia,i2s-controller = <&tegra_i2s1>;
 		nvidia,audio-codec = <&wm8903>;
 
 		nvidia,spkr-en-gpios = <&wm8903 2 GPIO_ACTIVE_HIGH>;
 		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_LOW>;
-		nvidia,headset;
+		nvidia,mic-det-gpios = <&gpio TEGRA_GPIO(X, 1) GPIO_ACTIVE_LOW>;
+		nvidia,coupled-mic-hp-det;
 
 		clocks = <&tegra_car TEGRA20_CLK_PLL_A>,
 			 <&tegra_car TEGRA20_CLK_PLL_A_OUT0>,
@@ -1283,8 +1266,3 @@
 		power-off-delay-us = <200>;
 	};
 };
-
-&emc_icc_dvfs_opp_table {
-	/delete-node/ opp-666000000;
-	/delete-node/ opp-760000000;
-};
diff --git a/arch/arm/boot/dts/tegra20-colibri-eval-v3.dts b/arch/arm/boot/dts/nvidia/tegra20-colibri-eval-v3.dts
index d2a3bf9d28bd..be2ead4147f2 100644
--- a/arch/arm/boot/dts/tegra20-colibri-eval-v3.dts
+++ b/arch/arm/boot/dts/nvidia/tegra20-colibri-eval-v3.dts
@@ -102,6 +102,8 @@
 
 	/* Colibri UART-A */
 	serial@70006000 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -143,6 +145,24 @@
 		status = "okay";
 	};
 
+	/* SPI4: Colibri SSP */
+	spi@7000da00 {
+		status = "okay";
+		spi-max-frequency = <25000000>;
+
+		can@0 {
+			compatible = "microchip,mcp2515";
+			reg = <0>;
+			clocks = <&clk16m>;
+			interrupt-parent = <&gpio>;
+			/* CAN_INT */
+			interrupts = <TEGRA_GPIO(A, 0) IRQ_TYPE_EDGE_FALLING>;
+			spi-max-frequency = <10000000>;
+			vdd-supply = <&reg_3v3>;
+			xceiver-supply = <&reg_5v0>;
+		};
+	};
+
 	/* EHCI instance 0: USB1_DP/N -> USBC_P/N */
 	usb@c5000000 {
 		status = "okay";
@@ -164,24 +184,6 @@
 		vbus-supply = <&reg_usbh_vbus>;
 	};
 
-	/* SPI4: Colibri SSP */
-	spi@7000da00 {
-		status = "okay";
-		spi-max-frequency = <25000000>;
-
-		can@0 {
-			compatible = "microchip,mcp2515";
-			reg = <0>;
-			clocks = <&clk16m>;
-			interrupt-parent = <&gpio>;
-			/* CAN_INT */
-			interrupts = <TEGRA_GPIO(A, 0) IRQ_TYPE_EDGE_FALLING>;
-			spi-max-frequency = <10000000>;
-			vdd-supply = <&reg_3v3>;
-			xceiver-supply = <&reg_5v0>;
-		};
-	};
-
 	/* SD/MMC */
 	mmc@c8000600 {
 		status = "okay";
@@ -200,7 +202,7 @@
 		pwms = <&pwm 0 5000000>; /* PWM<A> */
 	};
 
-	clk16m: osc3 {
+	clk16m: clock-osc3 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <16000000>;
@@ -209,7 +211,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "SODIMM pin 45 wakeup";
 			gpios = <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_WAKEUP>;
diff --git a/arch/arm/boot/dts/tegra20-colibri-iris.dts b/arch/arm/boot/dts/nvidia/tegra20-colibri-iris.dts
index 00ecbbd5e9e1..1da202ad1ded 100644
--- a/arch/arm/boot/dts/tegra20-colibri-iris.dts
+++ b/arch/arm/boot/dts/nvidia/tegra20-colibri-iris.dts
@@ -102,6 +102,8 @@
 
 	/* Colibri UART-A */
 	serial@70006000 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -143,6 +145,12 @@
 		status = "okay";
 	};
 
+	/* SPI4: Colibri SSP */
+	spi@7000da00 {
+		status = "okay";
+		spi-max-frequency = <25000000>;
+	};
+
 	/* EHCI instance 0: USB1_DP/N -> USBC_P/N */
 	usb@c5000000 {
 		status = "okay";
@@ -164,12 +172,6 @@
 		vbus-supply = <&reg_usbh_vbus>;
 	};
 
-	/* SPI4: Colibri SSP */
-	spi@7000da00 {
-		status = "okay";
-		spi-max-frequency = <25000000>;
-	};
-
 	/* SD/MMC */
 	mmc@c8000600 {
 		status = "okay";
@@ -191,7 +193,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "SODIMM pin 45 wakeup";
 			gpios = <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_WAKEUP>;
diff --git a/arch/arm/boot/dts/tegra20-colibri.dtsi b/arch/arm/boot/dts/nvidia/tegra20-colibri.dtsi
index 8ebd8afc857d..2ff7be8f1382 100644
--- a/arch/arm/boot/dts/tegra20-colibri.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra20-colibri.dtsi
@@ -27,6 +27,31 @@
 		};
 	};
 
+	gpio@6000d000 {
+		lan-reset-n-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(V, 4) GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "LAN_RESET#";
+		};
+
+		/* Tri-stating GMI_WR_N on SODIMM pin 99 nPWE */
+		npwe-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(T, 5) GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "Tri-state nPWE";
+		};
+
+		/* Not tri-stating GMI_WR_N on SODIMM pin 93 RDnWR */
+		rdnwr-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(T, 6) GPIO_ACTIVE_HIGH>;
+			output-low;
+			line-name = "Not tri-state RDnWR";
+		};
+	};
+
 	pinmux@70000014 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&state_default>;
@@ -420,19 +445,21 @@
 
 	tegra_ac97: ac97@70002000 {
 		status = "okay";
-		nvidia,codec-reset-gpio =
-			<&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_HIGH>;
-		nvidia,codec-sync-gpio =
+		nvidia,codec-reset-gpios =
+			<&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_LOW>;
+		nvidia,codec-sync-gpios =
 			<&gpio TEGRA_GPIO(P, 0) GPIO_ACTIVE_HIGH>;
 	};
 
 	serial@70006040 {
 		compatible = "nvidia,tegra20-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 	};
 
 	serial@70006300 {
 		compatible = "nvidia,tegra20-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 	};
 
@@ -705,12 +732,16 @@
 		vbus-supply = <&reg_lan_v_bus>;
 	};
 
-	clk32k_in: xtal3 {
+	clk32k_in: clock-xtal3 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <32768>;
 	};
 
+	opp-table-emc {
+		/delete-node/ opp-760000000;
+	};
+
 	reg_lan_v_bus: regulator-lan-v-bus {
 		compatible = "regulator-fixed";
 		regulator-name = "LAN_V_BUS";
@@ -745,32 +776,3 @@
 		clock-names = "pll_a", "pll_a_out0", "mclk";
 	};
 };
-
-&emc_icc_dvfs_opp_table {
-	/delete-node/ opp-760000000;
-};
-
-&gpio {
-	lan-reset-n-hog {
-		gpio-hog;
-		gpios = <TEGRA_GPIO(V, 4) GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "LAN_RESET#";
-	};
-
-	/* Tri-stating GMI_WR_N on SODIMM pin 99 nPWE */
-	npwe-hog {
-		gpio-hog;
-		gpios = <TEGRA_GPIO(T, 5) GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "Tri-state nPWE";
-	};
-
-	/* Not tri-stating GMI_WR_N on SODIMM pin 93 RDnWR */
-	rdnwr-hog {
-		gpio-hog;
-		gpios = <TEGRA_GPIO(T, 6) GPIO_ACTIVE_HIGH>;
-		output-low;
-		line-name = "Not tri-state RDnWR";
-	};
-};
diff --git a/arch/arm/boot/dts/tegra20-cpu-opp-microvolt.dtsi b/arch/arm/boot/dts/nvidia/tegra20-cpu-opp-microvolt.dtsi
index 7330c1b13d93..7330c1b13d93 100644
--- a/arch/arm/boot/dts/tegra20-cpu-opp-microvolt.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra20-cpu-opp-microvolt.dtsi
diff --git a/arch/arm/boot/dts/tegra20-cpu-opp.dtsi b/arch/arm/boot/dts/nvidia/tegra20-cpu-opp.dtsi
index 47c8e78ca958..47c8e78ca958 100644
--- a/arch/arm/boot/dts/tegra20-cpu-opp.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra20-cpu-opp.dtsi
diff --git a/arch/arm/boot/dts/tegra20-harmony.dts b/arch/arm/boot/dts/nvidia/tegra20-harmony.dts
index 79b6b79fab65..5c31a6c8dabe 100644
--- a/arch/arm/boot/dts/tegra20-harmony.dts
+++ b/arch/arm/boot/dts/nvidia/tegra20-harmony.dts
@@ -273,6 +273,8 @@
 	};
 
 	serial@70006300 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -648,7 +650,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
diff --git a/arch/arm/boot/dts/tegra20-medcom-wide.dts b/arch/arm/boot/dts/nvidia/tegra20-medcom-wide.dts
index f144487c5da3..8c657182fff3 100644
--- a/arch/arm/boot/dts/tegra20-medcom-wide.dts
+++ b/arch/arm/boot/dts/nvidia/tegra20-medcom-wide.dts
@@ -15,10 +15,6 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	pwm@7000a000 {
-		status = "okay";
-	};
-
 	host1x@50000000 {
 		dc@54200000 {
 			rgb {
@@ -28,6 +24,10 @@
 		};
 	};
 
+	pwm@7000a000 {
+		status = "okay";
+	};
+
 	i2c@7000c000 {
 		wm8903: wm8903@1a {
 			compatible = "wlf,wm8903";
diff --git a/arch/arm/boot/dts/tegra20-paz00.dts b/arch/arm/boot/dts/nvidia/tegra20-paz00.dts
index 0fb4b1f5bc1c..1408e1e00759 100644
--- a/arch/arm/boot/dts/tegra20-paz00.dts
+++ b/arch/arm/boot/dts/nvidia/tegra20-paz00.dts
@@ -279,10 +279,14 @@
 	};
 
 	serial@70006000 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
 	serial@70006200 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -307,67 +311,19 @@
 		clock-frequency = <100000>;
 	};
 
-	nvec@7000c500 {
+	i2c@7000c500 {
 		compatible = "nvidia,nvec";
-		reg = <0x7000c500 0x100>;
-		interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
-		#address-cells = <1>;
-		#size-cells = <0>;
+
+		/delete-property/ #address-cells;
+		/delete-property/ #size-cells;
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
+
 		clock-frequency = <80000>;
 		request-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_HIGH>;
 		slave-addr = <138>;
-		clocks = <&tegra_car TEGRA20_CLK_I2C3>,
-			 <&tegra_car TEGRA20_CLK_PLL_P_OUT3>;
-		clock-names = "div-clk", "fast-clk";
-		resets = <&tegra_car 67>;
-		reset-names = "i2c";
-	};
-
-	memory-controller@7000f400 {
-		nvidia,use-ram-code;
-
-		emc-tables@0 {
-			nvidia,ram-code = <0x0>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-
-			emc-table@166500 {
-				reg = <166500>;
-				compatible = "nvidia,tegra20-emc-table";
-				clock-frequency = <166500>;
-				nvidia,emc-registers = <0x0000000a 0x00000016
-					0x00000008 0x00000003 0x00000004 0x00000004
-					0x00000002 0x0000000c 0x00000003 0x00000003
-					0x00000002 0x00000001 0x00000004 0x00000005
-					0x00000004 0x00000009 0x0000000d 0x000004df
-					0x00000000 0x00000003 0x00000003 0x00000003
-					0x00000003 0x00000001 0x0000000a 0x000000c8
-					0x00000003 0x00000006 0x00000004 0x00000008
-					0x00000002 0x00000000 0x00000000 0x00000002
-					0x00000000 0x00000000 0x00000083 0xe03b0323
-					0x007fe010 0x00001414 0x00000000 0x00000000
-					0x00000000 0x00000000 0x00000000 0x00000000>;
-			};
 
-			emc-table@333000 {
-				reg = <333000>;
-				compatible = "nvidia,tegra20-emc-table";
-				clock-frequency = <333000>;
-				nvidia,emc-registers = <0x00000018 0x00000033
-					0x00000012 0x00000004 0x00000004 0x00000005
-					0x00000003 0x0000000c 0x00000006 0x00000006
-					0x00000003 0x00000001 0x00000004 0x00000005
-					0x00000004 0x00000009 0x0000000d 0x00000bff
-					0x00000000 0x00000003 0x00000003 0x00000006
-					0x00000006 0x00000001 0x00000011 0x000000c8
-					0x00000003 0x0000000e 0x00000007 0x00000008
-					0x00000002 0x00000000 0x00000000 0x00000002
-					0x00000000 0x00000000 0x00000083 0xf0440303
-					0x007fe010 0x00001414 0x00000000 0x00000000
-					0x00000000 0x00000000 0x00000000 0x00000000>;
-			};
-		};
+		status = "okay";
 	};
 
 	i2c@7000d000 {
@@ -532,6 +488,96 @@
 		core-supply = <&core_vdd_reg>;
 	};
 
+	memory-controller@7000f400 {
+		nvidia,use-ram-code;
+
+		emc-tables@0 {
+			nvidia,ram-code = <0x0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			emc-table@166500 {
+				reg = <166500>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <166500>;
+				nvidia,emc-registers = <0x0000000a 0x00000016
+					0x00000008 0x00000003 0x00000004 0x00000004
+					0x00000002 0x0000000c 0x00000003 0x00000003
+					0x00000002 0x00000001 0x00000004 0x00000005
+					0x00000004 0x00000009 0x0000000d 0x000004df
+					0x00000000 0x00000003 0x00000003 0x00000003
+					0x00000003 0x00000001 0x0000000a 0x000000c8
+					0x00000003 0x00000006 0x00000004 0x00000008
+					0x00000002 0x00000000 0x00000000 0x00000002
+					0x00000000 0x00000000 0x00000083 0xe03b0323
+					0x007fe010 0x00001414 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			emc-table@333000 {
+				reg = <333000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <333000>;
+				nvidia,emc-registers = <0x00000018 0x00000033
+					0x00000012 0x00000004 0x00000004 0x00000005
+					0x00000003 0x0000000c 0x00000006 0x00000006
+					0x00000003 0x00000001 0x00000004 0x00000005
+					0x00000004 0x00000009 0x0000000d 0x00000bff
+					0x00000000 0x00000003 0x00000003 0x00000006
+					0x00000006 0x00000001 0x00000011 0x000000c8
+					0x00000003 0x0000000e 0x00000007 0x00000008
+					0x00000002 0x00000000 0x00000000 0x00000002
+					0x00000000 0x00000000 0x00000083 0xf0440303
+					0x007fe010 0x00001414 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+		};
+
+		emc-tables@1 {
+			nvidia,ram-code = <0x1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			emc-table@166500 {
+				reg = <166500>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <166500>;
+				nvidia,emc-registers = <0x0000000a 0x00000016
+					0x00000008 0x00000003 0x00000004 0x00000004
+					0x00000002 0x0000000c 0x00000003 0x00000003
+					0x00000002 0x00000001 0x00000004 0x00000005
+					0x00000004 0x00000009 0x0000000d 0x000004df
+					0x00000000 0x00000003 0x00000003 0x00000003
+					0x00000003 0x00000001 0x0000000a 0x000000c8
+					0x00000003 0x00000006 0x00000004 0x00000008
+					0x00000002 0x00000000 0x00000000 0x00000002
+					0x00000000 0x00000000 0x00000083 0xe03b0323
+					0x007fe010 0x00001414 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			emc-table@333000 {
+				reg = <333000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <333000>;
+				nvidia,emc-registers = <0x00000018 0x00000033
+					0x00000012 0x00000004 0x00000004 0x00000005
+					0x00000003 0x0000000c 0x00000006 0x00000006
+					0x00000003 0x00000001 0x00000004 0x00000005
+					0x00000004 0x00000009 0x0000000d 0x00000bff
+					0x00000000 0x00000003 0x00000003 0x00000006
+					0x00000006 0x00000001 0x00000011 0x000000c8
+					0x00000003 0x0000000e 0x00000007 0x00000008
+					0x00000002 0x00000000 0x00000000 0x00000002
+					0x00000000 0x00000000 0x00000083 0xf0440303
+					0x007fe010 0x00001414 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+		};
+	};
+
 	usb@c5000000 {
 		compatible = "nvidia,tegra20-udc";
 		status = "okay";
@@ -593,10 +639,24 @@
 		#clock-cells = <0>;
 	};
 
+	cpus {
+		cpu0: cpu@0 {
+			cpu-supply = <&cpu_vdd_reg>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+
+		cpu1: cpu@1 {
+			cpu-supply = <&cpu_vdd_reg>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+	};
+
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "Wakeup";
 			gpios = <&gpio TEGRA_GPIO(J, 7) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_WAKEUP>;
@@ -614,6 +674,10 @@
 		};
 	};
 
+	opp-table-emc {
+		/delete-node/ opp-760000000;
+	};
+
 	panel: panel {
 		compatible = "samsung,ltn101nt05";
 
@@ -668,20 +732,6 @@
 		clock-names = "pll_a", "pll_a_out0", "mclk";
 	};
 
-	cpus {
-		cpu0: cpu@0 {
-			cpu-supply = <&cpu_vdd_reg>;
-			operating-points-v2 = <&cpu0_opp_table>;
-			#cooling-cells = <2>;
-		};
-
-		cpu1: cpu@1 {
-			cpu-supply = <&cpu_vdd_reg>;
-			operating-points-v2 = <&cpu0_opp_table>;
-			#cooling-cells = <2>;
-		};
-	};
-
 	thermal-zones {
 		cpu-thermal {
 			polling-delay-passive = <500>; /* milliseconds */
@@ -715,7 +765,3 @@
 		};
 	};
 };
-
-&emc_icc_dvfs_opp_table {
-	/delete-node/ opp-760000000;
-};
diff --git a/arch/arm/boot/dts/tegra20-peripherals-opp.dtsi b/arch/arm/boot/dts/nvidia/tegra20-peripherals-opp.dtsi
index 1b808233a933..1b808233a933 100644
--- a/arch/arm/boot/dts/tegra20-peripherals-opp.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra20-peripherals-opp.dtsi
diff --git a/arch/arm/boot/dts/tegra20-plutux.dts b/arch/arm/boot/dts/nvidia/tegra20-plutux.dts
index 71a8236491df..71a8236491df 100644
--- a/arch/arm/boot/dts/tegra20-plutux.dts
+++ b/arch/arm/boot/dts/nvidia/tegra20-plutux.dts
diff --git a/arch/arm/boot/dts/tegra20-seaboard.dts b/arch/arm/boot/dts/nvidia/tegra20-seaboard.dts
index c4a6a6a94559..e944ae9b86c2 100644
--- a/arch/arm/boot/dts/tegra20-seaboard.dts
+++ b/arch/arm/boot/dts/nvidia/tegra20-seaboard.dts
@@ -285,7 +285,7 @@
 			};
 		};
 
-		state_i2cmux_ddc: pinmux_i2cmux_ddc {
+		state_i2cmux_ddc: pinmux-i2cmux-ddc {
 			ddc {
 				nvidia,pins = "ddc";
 				nvidia,function = "i2c2";
@@ -296,25 +296,25 @@
 			};
 		};
 
-		state_i2cmux_pta: pinmux_i2cmux_pta {
+		state_i2cmux_idle: pinmux-i2cmux-idle {
 			ddc {
 				nvidia,pins = "ddc";
 				nvidia,function = "rsvd4";
 			};
 			pta {
 				nvidia,pins = "pta";
-				nvidia,function = "i2c2";
+				nvidia,function = "rsvd4";
 			};
 		};
 
-		state_i2cmux_idle: pinmux_i2cmux_idle {
+		state_i2cmux_pta: pinmux-i2cmux-pta {
 			ddc {
 				nvidia,pins = "ddc";
 				nvidia,function = "rsvd4";
 			};
 			pta {
 				nvidia,pins = "pta";
-				nvidia,function = "rsvd4";
+				nvidia,function = "i2c2";
 			};
 		};
 	};
@@ -324,6 +324,8 @@
 	};
 
 	serial@70006300 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -370,38 +372,6 @@
 		clock-frequency = <100000>;
 	};
 
-	i2cmux {
-		compatible = "i2c-mux-pinctrl";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		i2c-parent = <&{/i2c@7000c400}>;
-
-		pinctrl-names = "ddc", "pta", "idle";
-		pinctrl-0 = <&state_i2cmux_ddc>;
-		pinctrl-1 = <&state_i2cmux_pta>;
-		pinctrl-2 = <&state_i2cmux_idle>;
-
-		hdmi_ddc: i2c@0 {
-			reg = <0>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		lvds_ddc: i2c@1 {
-			reg = <1>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			smart-battery@b {
-				compatible = "ti,bq20z75", "sbs,sbs-battery";
-				reg = <0xb>;
-				sbs,i2c-retry-count = <2>;
-				sbs,poll-retry-count = <10>;
-			};
-		};
-	};
-
 	i2c@7000c500 {
 		status = "okay";
 		clock-frequency = <400000>;
@@ -800,14 +770,14 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			wakeup-source;
 		};
 
-		lid {
+		switch-lid {
 			label = "Lid";
 			gpios = <&gpio TEGRA_GPIO(C, 7) GPIO_ACTIVE_HIGH>;
 			linux,input-type = <5>; /* EV_SW */
@@ -817,6 +787,38 @@
 		};
 	};
 
+	i2cmux {
+		compatible = "i2c-mux-pinctrl";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c-parent = <&{/i2c@7000c400}>;
+
+		pinctrl-names = "ddc", "pta", "idle";
+		pinctrl-0 = <&state_i2cmux_ddc>;
+		pinctrl-1 = <&state_i2cmux_pta>;
+		pinctrl-2 = <&state_i2cmux_idle>;
+
+		hdmi_ddc: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		lvds_ddc: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			smart-battery@b {
+				compatible = "ti,bq20z75", "sbs,sbs-battery";
+				reg = <0xb>;
+				sbs,i2c-retry-count = <2>;
+				sbs,poll-retry-count = <10>;
+			};
+		};
+	};
+
 	panel: panel {
 		compatible = "chunghwa,claa101wa01a";
 
diff --git a/arch/arm/boot/dts/tegra20-tamonten.dtsi b/arch/arm/boot/dts/nvidia/tegra20-tamonten.dtsi
index 0e19bd0a847c..5c214dd060bb 100644
--- a/arch/arm/boot/dts/tegra20-tamonten.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra20-tamonten.dtsi
@@ -249,7 +249,7 @@
 			};
 		};
 
-		state_i2cmux_ddc: pinmux_i2cmux_ddc {
+		state_i2cmux_ddc: pinmux-i2cmux-ddc {
 			ddc {
 				nvidia,pins = "ddc";
 				nvidia,function = "i2c2";
@@ -260,25 +260,25 @@
 			};
 		};
 
-		state_i2cmux_pta: pinmux_i2cmux_pta {
+		state_i2cmux_idle: pinmux-i2cmux-idle {
 			ddc {
 				nvidia,pins = "ddc";
 				nvidia,function = "rsvd4";
 			};
 			pta {
 				nvidia,pins = "pta";
-				nvidia,function = "i2c2";
+				nvidia,function = "rsvd4";
 			};
 		};
 
-		state_i2cmux_idle: pinmux_i2cmux_idle {
+		state_i2cmux_pta: pinmux-i2cmux-pta {
 			ddc {
 				nvidia,pins = "ddc";
 				nvidia,function = "rsvd4";
 			};
 			pta {
 				nvidia,pins = "pta";
-				nvidia,function = "rsvd4";
+				nvidia,function = "i2c2";
 			};
 		};
 	};
@@ -288,6 +288,8 @@
 	};
 
 	serial@70006300 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -301,31 +303,6 @@
 		status = "okay";
 	};
 
-	i2cmux {
-		compatible = "i2c-mux-pinctrl";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		i2c-parent = <&{/i2c@7000c400}>;
-
-		pinctrl-names = "ddc", "pta", "idle";
-		pinctrl-0 = <&state_i2cmux_ddc>;
-		pinctrl-1 = <&state_i2cmux_pta>;
-		pinctrl-2 = <&state_i2cmux_idle>;
-
-		hdmi_ddc: i2c@0 {
-			reg = <0>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		i2c@1 {
-			reg = <1>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-	};
-
 	i2c@7000d000 {
 		clock-frequency = <400000>;
 		status = "okay";
@@ -509,6 +486,31 @@
 		#clock-cells = <0>;
 	};
 
+	i2cmux {
+		compatible = "i2c-mux-pinctrl";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c-parent = <&{/i2c@7000c400}>;
+
+		pinctrl-names = "ddc", "pta", "idle";
+		pinctrl-0 = <&state_i2cmux_ddc>;
+		pinctrl-1 = <&state_i2cmux_pta>;
+		pinctrl-2 = <&state_i2cmux_idle>;
+
+		hdmi_ddc: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
 	pci_vdd_reg: regulator-1v05 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_1v05";
diff --git a/arch/arm/boot/dts/tegra20-tec.dts b/arch/arm/boot/dts/nvidia/tegra20-tec.dts
index 4f41c74384b2..4f41c74384b2 100644
--- a/arch/arm/boot/dts/tegra20-tec.dts
+++ b/arch/arm/boot/dts/nvidia/tegra20-tec.dts
diff --git a/arch/arm/boot/dts/tegra20-trimslice.dts b/arch/arm/boot/dts/nvidia/tegra20-trimslice.dts
index 9d0c86711de2..4caeeb9f1e1d 100644
--- a/arch/arm/boot/dts/tegra20-trimslice.dts
+++ b/arch/arm/boot/dts/nvidia/tegra20-trimslice.dts
@@ -2,6 +2,7 @@
 /dts-v1/;
 
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
 #include "tegra20.dtsi"
 #include "tegra20-cpu-opp.dtsi"
 
@@ -201,16 +202,17 @@
 			conf_ata {
 				nvidia,pins = "ata", "atc", "atd", "ate",
 					"crtp", "dap2", "dap3", "dap4", "dta",
-					"dtb", "dtc", "dtd", "dte", "gmb",
-					"gme", "i2cp", "pta", "slxc", "slxd",
-					"spdi", "spdo", "uda";
+					"dtb", "dtc", "dtd", "gmb", "gme",
+					"i2cp", "pta", "slxc", "slxd", "spdi",
+					"spdo", "uda";
 				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
 				nvidia,tristate = <TEGRA_PIN_ENABLE>;
 			};
 			conf_atb {
 				nvidia,pins = "atb", "cdev1", "cdev2", "dap1",
-					"gma", "gmc", "gmd", "gpu", "gpu7",
-					"gpv", "sdio1", "slxa", "slxk", "uac";
+					"dte", "gma", "gmc", "gmd", "gpu",
+					"gpu7", "gpv", "sdio1", "slxa", "slxk",
+					"uac";
 				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
 			};
@@ -276,6 +278,8 @@
 	};
 
 	serial@70006000 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -385,10 +389,20 @@
 		#clock-cells = <0>;
 	};
 
+	cpus {
+		cpu0: cpu@0 {
+			operating-points-v2 = <&cpu0_opp_table>;
+		};
+
+		cpu@1 {
+			operating-points-v2 = <&cpu0_opp_table>;
+		};
+	};
+
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(X, 6) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -396,6 +410,24 @@
 		};
 	};
 
+	leds {
+		compatible = "gpio-leds";
+
+		led-ds2 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <2>;
+			gpios = <&gpio TEGRA_GPIO(D, 2) GPIO_ACTIVE_LOW>;
+		};
+
+		led-ds3 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <3>;
+			gpios = <&gpio TEGRA_GPIO(BB, 5) GPIO_ACTIVE_LOW>;
+		};
+	};
+
 	poweroff {
 		compatible = "gpio-poweroff";
 		gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_LOW>;
@@ -462,14 +494,4 @@
 			 <&tegra_car TEGRA20_CLK_CDEV1>;
 		clock-names = "pll_a", "pll_a_out0", "mclk";
 	};
-
-	cpus {
-		cpu0: cpu@0 {
-			operating-points-v2 = <&cpu0_opp_table>;
-		};
-
-		cpu@1 {
-			operating-points-v2 = <&cpu0_opp_table>;
-		};
-	};
 };
diff --git a/arch/arm/boot/dts/tegra20-ventana.dts b/arch/arm/boot/dts/nvidia/tegra20-ventana.dts
index b0a00970b61c..f3273941437c 100644
--- a/arch/arm/boot/dts/tegra20-ventana.dts
+++ b/arch/arm/boot/dts/nvidia/tegra20-ventana.dts
@@ -284,7 +284,7 @@
 			};
 		};
 
-		state_i2cmux_ddc: pinmux_i2cmux_ddc {
+		state_i2cmux_ddc: pinmux-i2cmux-ddc {
 			ddc {
 				nvidia,pins = "ddc";
 				nvidia,function = "i2c2";
@@ -295,25 +295,25 @@
 			};
 		};
 
-		state_i2cmux_pta: pinmux_i2cmux_pta {
+		state_i2cmux_idle: pinmux-i2cmux-idle {
 			ddc {
 				nvidia,pins = "ddc";
 				nvidia,function = "rsvd4";
 			};
 			pta {
 				nvidia,pins = "pta";
-				nvidia,function = "i2c2";
+				nvidia,function = "rsvd4";
 			};
 		};
 
-		state_i2cmux_idle: pinmux_i2cmux_idle {
+		state_i2cmux_pta: pinmux-i2cmux-pta {
 			ddc {
 				nvidia,pins = "ddc";
 				nvidia,function = "rsvd4";
 			};
 			pta {
 				nvidia,pins = "pta";
-				nvidia,function = "rsvd4";
+				nvidia,function = "i2c2";
 			};
 		};
 	};
@@ -323,6 +323,8 @@
 	};
 
 	serial@70006300 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -362,31 +364,6 @@
 		clock-frequency = <100000>;
 	};
 
-	i2cmux {
-		compatible = "i2c-mux-pinctrl";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		i2c-parent = <&{/i2c@7000c400}>;
-
-		pinctrl-names = "ddc", "pta", "idle";
-		pinctrl-0 = <&state_i2cmux_ddc>;
-		pinctrl-1 = <&state_i2cmux_pta>;
-		pinctrl-2 = <&state_i2cmux_idle>;
-
-		hdmi_ddc: i2c@0 {
-			reg = <0>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		lvds_ddc: i2c@1 {
-			reg = <1>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-	};
-
 	i2c@7000c500 {
 		status = "okay";
 		clock-frequency = <400000>;
@@ -628,7 +605,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -636,6 +613,31 @@
 		};
 	};
 
+	i2cmux {
+		compatible = "i2c-mux-pinctrl";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c-parent = <&{/i2c@7000c400}>;
+
+		pinctrl-names = "ddc", "pta", "idle";
+		pinctrl-0 = <&state_i2cmux_ddc>;
+		pinctrl-1 = <&state_i2cmux_pta>;
+		pinctrl-2 = <&state_i2cmux_idle>;
+
+		hdmi_ddc: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		lvds_ddc: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
 	panel: panel {
 		compatible = "chunghwa,claa101wa01a";
 
diff --git a/arch/arm/boot/dts/tegra20.dtsi b/arch/arm/boot/dts/nvidia/tegra20.dtsi
index 62bf0b306472..882adb7f2f26 100644
--- a/arch/arm/boot/dts/tegra20.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra20.dtsi
@@ -284,7 +284,7 @@
 		reg = <0x60007000 0x1000>;
 	};
 
-	apbdma: dma@6000a000 {
+	apbdma: dma-controller@6000a000 {
 		compatible = "nvidia,tegra20-apbdma";
 		reg = <0x6000a000 0x1200>;
 		interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
@@ -356,12 +356,6 @@
 		operating-points-v2 = <&vde_dvfs_opp_table>;
 	};
 
-	apbmisc@70000800 {
-		compatible = "nvidia,tegra20-apbmisc";
-		reg = <0x70000800 0x64>, /* Chip revision */
-		      <0x70000008 0x04>; /* Strapping options */
-	};
-
 	pinmux: pinmux@70000014 {
 		compatible = "nvidia,tegra20-pinmux";
 		reg = <0x70000014 0x10>, /* Tri-state registers */
@@ -370,6 +364,12 @@
 		      <0x70000868 0xa8>; /* Pad control registers */
 	};
 
+	apbmisc@70000800 {
+		compatible = "nvidia,tegra20-apbmisc";
+		reg = <0x70000800 0x64>, /* Chip revision */
+		      <0x70000008 0x04>; /* Strapping options */
+	};
+
 	das@70000c00 {
 		compatible = "nvidia,tegra20-das";
 		reg = <0x70000c00 0x80>;
@@ -442,7 +442,6 @@
 		interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA20_CLK_UARTA>;
 		resets = <&tegra_car 6>;
-		reset-names = "serial";
 		dmas = <&apbdma 8>, <&apbdma 8>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -455,7 +454,6 @@
 		interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA20_CLK_UARTB>;
 		resets = <&tegra_car 7>;
-		reset-names = "serial";
 		dmas = <&apbdma 9>, <&apbdma 9>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -468,7 +466,6 @@
 		interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA20_CLK_UARTC>;
 		resets = <&tegra_car 55>;
-		reset-names = "serial";
 		dmas = <&apbdma 10>, <&apbdma 10>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -481,7 +478,6 @@
 		interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA20_CLK_UARTD>;
 		resets = <&tegra_car 65>;
-		reset-names = "serial";
 		dmas = <&apbdma 19>, <&apbdma 19>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -494,7 +490,6 @@
 		interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA20_CLK_UARTE>;
 		resets = <&tegra_car 66>;
-		reset-names = "serial";
 		dmas = <&apbdma 20>, <&apbdma 20>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -542,13 +537,6 @@
 		status = "disabled";
 	};
 
-	rtc@7000e000 {
-		compatible = "nvidia,tegra20-rtc";
-		reg = <0x7000e000 0x100>;
-		interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&tegra_car TEGRA20_CLK_RTC>;
-	};
-
 	i2c@7000c000 {
 		compatible = "nvidia,tegra20-i2c";
 		reg = <0x7000c000 0x100>;
@@ -683,6 +671,13 @@
 		status = "disabled";
 	};
 
+	rtc@7000e000 {
+		compatible = "nvidia,tegra20-rtc";
+		reg = <0x7000e000 0x100>;
+		interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&tegra_car TEGRA20_CLK_RTC>;
+	};
+
 	kbc@7000e200 {
 		compatible = "nvidia,tegra20-kbc";
 		reg = <0x7000e200 0x100>;
@@ -706,6 +701,16 @@
 		};
 
 		powergates {
+			pd_mpe: mpe {
+				clocks = <&tegra_car TEGRA20_CLK_MPE>;
+				resets = <&mc TEGRA20_MC_RESET_MPEA>,
+					 <&mc TEGRA20_MC_RESET_MPEB>,
+					 <&mc TEGRA20_MC_RESET_MPEC>,
+					 <&tegra_car TEGRA20_CLK_MPE>;
+				power-domains = <&pd_core>;
+				#power-domain-cells = <0>;
+			};
+
 			pd_3d: td {
 				clocks = <&tegra_car TEGRA20_CLK_GR3D>;
 				resets = <&mc TEGRA20_MC_RESET_3D>,
@@ -714,6 +719,14 @@
 				#power-domain-cells = <0>;
 			};
 
+			pd_vde: vdec {
+				clocks = <&tegra_car TEGRA20_CLK_VDE>;
+				resets = <&mc TEGRA20_MC_RESET_VDE>,
+					 <&tegra_car TEGRA20_CLK_VDE>;
+				power-domains = <&pd_core>;
+				#power-domain-cells = <0>;
+			};
+
 			pd_venc: venc {
 				clocks = <&tegra_car TEGRA20_CLK_ISP>,
 					 <&tegra_car TEGRA20_CLK_VI>,
@@ -726,24 +739,6 @@
 				power-domains = <&pd_core>;
 				#power-domain-cells = <0>;
 			};
-
-			pd_vde: vdec {
-				clocks = <&tegra_car TEGRA20_CLK_VDE>;
-				resets = <&mc TEGRA20_MC_RESET_VDE>,
-					 <&tegra_car TEGRA20_CLK_VDE>;
-				power-domains = <&pd_core>;
-				#power-domain-cells = <0>;
-			};
-
-			pd_mpe: mpe {
-				clocks = <&tegra_car TEGRA20_CLK_MPE>;
-				resets = <&mc TEGRA20_MC_RESET_MPEA>,
-					 <&mc TEGRA20_MC_RESET_MPEB>,
-					 <&mc TEGRA20_MC_RESET_MPEC>,
-					 <&tegra_car TEGRA20_CLK_MPE>;
-				power-domains = <&pd_core>;
-				#power-domain-cells = <0>;
-			};
 		};
 	};
 
@@ -1049,13 +1044,13 @@
 		simple-audio-card,dai-link@0 {
 			reg = <0>;
 
-			cpu {
-				sound-dai = <&tegra_spdif>;
-			};
-
 			codec {
 				sound-dai = <&tegra_hdmi>;
 			};
+
+			cpu {
+				sound-dai = <&tegra_spdif>;
+			};
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/tegra30-apalis-eval.dts b/arch/arm/boot/dts/nvidia/tegra30-apalis-eval.dts
index 93b83b3c5655..ccb9f29c5de3 100644
--- a/arch/arm/boot/dts/tegra30-apalis-eval.dts
+++ b/arch/arm/boot/dts/nvidia/tegra30-apalis-eval.dts
@@ -47,8 +47,20 @@
 		};
 	};
 
+	gpio@6000d000 {
+		/* Apalis GPIO7 MXM3 pin 15 PLX PEX 8605 PCIe Switch Reset */
+		pex-perst-n-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(S, 7) GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "PEX_PERST_N";
+		};
+	};
+
 	/* Apalis UART1 */
 	serial@70006000 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -79,11 +91,6 @@
 		status = "okay";
 		clock-frequency = <400000>;
 
-		pcie-switch@58 {
-			compatible = "plx,pex8605";
-			reg = <0x58>;
-		};
-
 		/* M41T0M6 real time clock on carrier board */
 		rtc@68 {
 			compatible = "st,m41t0";
@@ -181,7 +188,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "WAKE1_MICO";
 			gpios = <&gpio TEGRA_GPIO(V, 1) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_WAKEUP>;
@@ -236,13 +243,3 @@
 		vin-supply = <&reg_5v0>;
 	};
 };
-
-&gpio {
-	/* Apalis GPIO7 MXM3 pin 15 PLX PEX 8605 PCIe Switch Reset */
-	pex-perst-n-hog {
-		gpio-hog;
-		gpios = <TEGRA_GPIO(S, 7) GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "PEX_PERST_N";
-	};
-};
diff --git a/arch/arm/boot/dts/tegra30-apalis-v1.1-eval.dts b/arch/arm/boot/dts/nvidia/tegra30-apalis-v1.1-eval.dts
index fbfa75e53f32..bc353324df43 100644
--- a/arch/arm/boot/dts/tegra30-apalis-v1.1-eval.dts
+++ b/arch/arm/boot/dts/nvidia/tegra30-apalis-v1.1-eval.dts
@@ -48,8 +48,20 @@
 		};
 	};
 
+	gpio@6000d000 {
+		/* Apalis GPIO7 MXM3 pin 15 PLX PEX 8605 PCIe Switch Reset */
+		pex-perst-n-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(S, 7) GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "PEX_PERST_N";
+		};
+	};
+
 	/* Apalis UART1 */
 	serial@70006000 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -80,11 +92,6 @@
 		status = "okay";
 		clock-frequency = <400000>;
 
-		pcie-switch@58 {
-			compatible = "plx,pex8605";
-			reg = <0x58>;
-		};
-
 		/* M41T0M6 real time clock on carrier board */
 		rtc@68 {
 			compatible = "st,m41t0";
@@ -182,7 +189,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "WAKE1_MICO";
 			gpios = <&gpio TEGRA_GPIO(V, 1) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_WAKEUP>;
@@ -254,13 +261,3 @@
 		vin-supply = <&vddio_sdmmc_1v8_reg>;
 	};
 };
-
-&gpio {
-	/* Apalis GPIO7 MXM3 pin 15 PLX PEX 8605 PCIe Switch Reset */
-	pex-perst-n-hog {
-		gpio-hog;
-		gpios = <TEGRA_GPIO(S, 7) GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "PEX_PERST_N";
-	};
-};
diff --git a/arch/arm/boot/dts/tegra30-apalis-v1.1.dtsi b/arch/arm/boot/dts/nvidia/tegra30-apalis-v1.1.dtsi
index 380f22a35821..ff0d684622f7 100644
--- a/arch/arm/boot/dts/tegra30-apalis-v1.1.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra30-apalis-v1.1.dtsi
@@ -829,16 +829,19 @@
 
 	serial@70006040 {
 		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 	};
 
 	serial@70006200 {
 		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 	};
 
 	serial@70006300 {
 		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 	};
 
@@ -993,8 +996,7 @@
 		touchscreen@41 {
 			compatible = "st,stmpe811";
 			reg = <0x41>;
-			irq-gpio = <&gpio TEGRA_GPIO(V, 0) IRQ_TYPE_LEVEL_LOW>;
-			interrupt-controller;
+			irq-gpio = <&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_LOW>;
 			id = <0>;
 			blocks = <0x5>;
 			irq-trigger = <0x1>;
@@ -1007,6 +1009,12 @@
 			/* ADC converstion time: 80 clocks */
 			st,sample-time = <4>;
 
+			stmpe_adc {
+				compatible = "st,stmpe-adc";
+				/* forbid to use ADC channels 3-0 (touch) */
+				st,norequest-mask = <0x0F>;
+			};
+
 			stmpe_touchscreen {
 				compatible = "st,stmpe-ts";
 				/* 8 sample average control */
@@ -1023,12 +1031,6 @@
 				/* 5 ms touch detect interrupt delay */
 				st,touch-det-delay = <5>;
 			};
-
-			stmpe_adc {
-				compatible = "st,stmpe-adc";
-				/* forbid to use ADC channels 3-0 (touch) */
-				st,norequest-mask = <0x0F>;
-			};
 		};
 
 		/*
@@ -1122,16 +1124,16 @@
 		mmc-ddr-1_8v;
 	};
 
-	clk32k_in: xtal1 {
+	clk16m: clock-osc4 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
-		clock-frequency = <32768>;
+		clock-frequency = <16000000>;
 	};
 
-	clk16m: osc4 {
+	clk32k_in: clock-xtal1 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
-		clock-frequency = <16000000>;
+		clock-frequency = <32768>;
 	};
 
 	reg_1v8_avdd_hdmi_pll: regulator-1v8-avdd-hdmi-pll {
diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/nvidia/tegra30-apalis.dtsi
index 9bdc4cb71449..d38f1dd38a90 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra30-apalis.dtsi
@@ -820,16 +820,19 @@
 
 	serial@70006040 {
 		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 	};
 
 	serial@70006200 {
 		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 	};
 
 	serial@70006300 {
 		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 	};
 
@@ -976,8 +979,7 @@
 		touchscreen@41 {
 			compatible = "st,stmpe811";
 			reg = <0x41>;
-			irq-gpio = <&gpio TEGRA_GPIO(V, 0) IRQ_TYPE_LEVEL_LOW>;
-			interrupt-controller;
+			irq-gpio = <&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_LOW>;
 			id = <0>;
 			blocks = <0x5>;
 			irq-trigger = <0x1>;
@@ -990,6 +992,12 @@
 			/* ADC converstion time: 80 clocks */
 			st,sample-time = <4>;
 
+			stmpe_adc {
+				compatible = "st,stmpe-adc";
+				/* forbid to use ADC channels 3-0 (touch) */
+				st,norequest-mask = <0x0F>;
+			};
+
 			stmpe_touchscreen {
 				compatible = "st,stmpe-ts";
 				/* 8 sample average control */
@@ -1006,12 +1014,6 @@
 				/* 5 ms touch detect interrupt delay */
 				st,touch-det-delay = <5>;
 			};
-
-			stmpe_adc {
-				compatible = "st,stmpe-adc";
-				/* forbid to use ADC channels 3-0 (touch) */
-				st,norequest-mask = <0x0F>;
-			};
 		};
 
 		/*
@@ -1105,16 +1107,16 @@
 		mmc-ddr-1_8v;
 	};
 
-	clk32k_in: xtal1 {
+	clk16m: clock-osc4 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
-		clock-frequency = <32768>;
+		clock-frequency = <16000000>;
 	};
 
-	clk16m: osc4 {
+	clk32k_in: clock-xtal1 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
-		clock-frequency = <16000000>;
+		clock-frequency = <32768>;
 	};
 
 	reg_1v8_avdd_hdmi_pll: regulator-1v8-avdd-hdmi-pll {
diff --git a/arch/arm/boot/dts/tegra30-asus-lvds-display.dtsi b/arch/arm/boot/dts/nvidia/tegra30-asus-lvds-display.dtsi
index a047abfa6369..680edff0f26f 100644
--- a/arch/arm/boot/dts/tegra30-asus-lvds-display.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-lvds-display.dtsi
@@ -2,13 +2,15 @@
 
 /* This dtsi file describes parts common for Asus T30 devices with a LVDS panel. */
 
+#include <dt-bindings/gpio/tegra-gpio.h>
+
 / {
 	host1x@50000000 {
 		lcd: dc@54200000 {
 			rgb {
 				status = "okay";
 
-				port@0 {
+				port {
 					dpi_output: endpoint {
 						remote-endpoint = <&bridge_input>;
 						bus-width = <24>;
diff --git a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-E1565.dts b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-E1565.dts
index a25b8560b0cd..a25b8560b0cd 100644
--- a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-E1565.dts
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-E1565.dts
diff --git a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-PM269.dts b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-PM269.dts
index 06ef13ea5df8..06ef13ea5df8 100644
--- a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-PM269.dts
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-PM269.dts
diff --git a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-common.dtsi b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-common.dtsi
index 2c2ad2a38f04..15f53babdc21 100644
--- a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-common.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-common.dtsi
@@ -29,6 +29,14 @@
 	 */
 	chosen {};
 
+	firmware {
+		trusted-foundations {
+			compatible = "tlm,trusted-foundations";
+			tlm,version-major = <0x0>;
+			tlm,version-minor = <0x0>;
+		};
+	};
+
 	memory@80000000 {
 		reg = <0x80000000 0x40000000>;
 	};
@@ -61,19 +69,19 @@
 	};
 
 	gpio@6000d000 {
+		init-low-power-mode-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(I, 6) GPIO_ACTIVE_HIGH>;
+			input;
+		};
+
 		init-mode-hog {
 			gpio-hog;
-			gpios =	<TEGRA_GPIO(DD, 7) GPIO_ACTIVE_HIGH>,
+			gpios = <TEGRA_GPIO(DD, 7) GPIO_ACTIVE_HIGH>,
 				<TEGRA_GPIO(CC, 6) GPIO_ACTIVE_HIGH>,
 				<TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>;
 			output-low;
 		};
-
-		init-low-power-mode-hog {
-			gpio-hog;
-			gpios = <TEGRA_GPIO(I, 6) GPIO_ACTIVE_HIGH>;
-			input;
-		};
 	};
 
 	pinmux@70000868 {
@@ -790,12 +798,14 @@
 
 	uartb: serial@70006040 {
 		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 		/* GPS BCM4751 */
 	};
 
 	uartc: serial@70006200 {
 		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 		status = "okay";
 
@@ -820,7 +830,7 @@
 			vddio-supply = <&vdd_1v8>;
 
 			device-wakeup-gpios = <&gpio TEGRA_GPIO(U, 1) GPIO_ACTIVE_HIGH>;
-			shutdown-gpios =      <&gpio TEGRA_GPIO(U, 0) GPIO_ACTIVE_HIGH>;
+			shutdown-gpios = <&gpio TEGRA_GPIO(U, 0) GPIO_ACTIVE_HIGH>;
 		};
 	};
 
@@ -833,7 +843,7 @@
 		status = "okay";
 
 		touchscreen@10 {
-			compatible ="elan,ektf3624";
+			compatible = "elan,ektf3624";
 			reg = <0x10>;
 
 			interrupt-parent = <&gpio>;
@@ -905,6 +915,9 @@
 			reg = <0x1c>;
 
 			realtek,dmic1-data-pin = <1>;
+
+			clocks = <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+			clock-names = "mclk";
 		};
 
 		nct72: temperature-sensor@4c {
@@ -977,17 +990,6 @@
 		};
 	};
 
-	brcm_wifi_pwrseq: wifi-pwrseq {
-		compatible = "mmc-pwrseq-simple";
-
-		clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
-		clock-names = "ext_clock";
-
-		reset-gpios = <&gpio TEGRA_GPIO(D, 4) GPIO_ACTIVE_LOW>;
-		post-power-on-delay-ms = <300>;
-		power-off-delay-us = <300>;
-	};
-
 	sdmmc3: mmc@78000400 {
 		status = "okay";
 
@@ -1093,15 +1095,11 @@
 
 	display-panel {
 		/*
-		 * Nexus 7 supports two compatible panel models:
-		 *
-		 *  1. hydis,hv070wx2-1e0
-		 *  2. chunghwa,claa070wp03xg
-		 *
-		 * We want to use timing which is optimized for Nexus 7,
-		 * hence we need to customize the timing.
+		 * Some device variants come with a Hydis HV070WX2-1E0, but
+		 * since they are all largely compatible, we'll go with the
+		 * Chunghwa one here.
 		 */
-		compatible = "panel-lvds";
+		compatible = "chunghwa,claa070wp03xg", "panel-lvds";
 
 		width-mm = <94>;
 		height-mm = <150>;
@@ -1113,28 +1111,10 @@
 		/delete-property/ ddc-i2c-bus;
 	};
 
-	firmware {
-		trusted-foundations {
-			compatible = "tlm,trusted-foundations";
-			tlm,version-major = <0x0>;
-			tlm,version-minor = <0x0>;
-		};
-	};
-
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		hall-sensor {
-			label = "Lid";
-			gpios = <&gpio TEGRA_GPIO(S, 6) GPIO_ACTIVE_LOW>;
-			linux,input-type = <EV_SW>;
-			linux,code = <SW_LID>;
-			debounce-interval = <500>;
-			wakeup-event-action = <EV_ACT_DEASSERTED>;
-			wakeup-source;
-		};
-
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -1143,7 +1123,16 @@
 			wakeup-source;
 		};
 
-		volume-up {
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio TEGRA_GPIO(Q, 3) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-volume-up {
 			label = "Volume Up";
 			gpios = <&gpio TEGRA_GPIO(Q, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
@@ -1152,16 +1141,28 @@
 			wakeup-source;
 		};
 
-		volume-down {
-			label = "Volume Down";
-			gpios = <&gpio TEGRA_GPIO(Q, 3) GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEDOWN>;
-			debounce-interval = <10>;
-			wakeup-event-action = <EV_ACT_ASSERTED>;
+		switch-hall-sensor {
+			label = "Lid";
+			gpios = <&gpio TEGRA_GPIO(S, 6) GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			debounce-interval = <500>;
+			wakeup-event-action = <EV_ACT_DEASSERTED>;
 			wakeup-source;
 		};
 	};
 
+	brcm_wifi_pwrseq: pwrseq-wifi {
+		compatible = "mmc-pwrseq-simple";
+
+		clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
+		clock-names = "ext_clock";
+
+		reset-gpios = <&gpio TEGRA_GPIO(D, 4) GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <300>;
+		power-off-delay-us = <300>;
+	};
+
 	vdd_5v0_sys: regulator-5v0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_5v0";
diff --git a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-maxim-pmic.dtsi b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-maxim-pmic.dtsi
index cd28e8782f7d..694c7fe37eb8 100644
--- a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-maxim-pmic.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-maxim-pmic.dtsi
@@ -22,13 +22,6 @@
 			pinctrl-names = "default";
 			pinctrl-0 = <&max77620_default>;
 
-			max77620_default: pinmux {
-				gpio4 {
-					pins = "gpio4";
-					function = "32k-out1";
-				};
-			};
-
 			cpu-pwr-req-hog {
 				gpio-hog;
 				gpios = <6 GPIO_ACTIVE_HIGH>;
@@ -49,6 +42,13 @@
 				};
 			};
 
+			max77620_default: pinmux {
+				gpio4 {
+					pins = "gpio4";
+					function = "32k-out1";
+				};
+			};
+
 			regulators {
 				in-sd0-supply = <&vdd_5v0_sys>;
 				in-sd1-supply = <&vdd_5v0_sys>;
diff --git a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-memory-timings.dtsi b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-memory-timings.dtsi
index 6c229e1d67e7..8944a4a5a8d7 100644
--- a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-memory-timings.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-memory-timings.dtsi
@@ -1562,16 +1562,16 @@
 			};
 		};
 	};
-};
 
-&emc_icc_dvfs_opp_table {
-	/delete-node/ opp-750000000-1300;
-	/delete-node/ opp-800000000-1300;
-	/delete-node/ opp-900000000-1350;
-};
+	opp-table-actmon {
+		/delete-node/ opp-750000000;
+		/delete-node/ opp-800000000;
+		/delete-node/ opp-900000000;
+	};
 
-&emc_bw_dfs_opp_table {
-	/delete-node/ opp-750000000;
-	/delete-node/ opp-800000000;
-	/delete-node/ opp-900000000;
+	opp-table-emc {
+		/delete-node/ opp-750000000-1300;
+		/delete-node/ opp-800000000-1300;
+		/delete-node/ opp-900000000-1350;
+	};
 };
diff --git a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-ti-pmic.dtsi b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-ti-pmic.dtsi
index ee4a3f482769..ee4a3f482769 100644
--- a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-ti-pmic.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper-ti-pmic.dtsi
diff --git a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper.dtsi b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper.dtsi
index 564cfcde21a9..c19a0419112a 100644
--- a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-grouper.dtsi
@@ -6,20 +6,6 @@
 / {
 	compatible = "asus,grouper", "nvidia,tegra30";
 
-	display-panel {
-		panel-timing {
-			clock-frequency = <68000000>;
-			hactive = <800>;
-			vactive = <1280>;
-			hfront-porch = <24>;
-			hback-porch = <32>;
-			hsync-len = <24>;
-			vsync-len = <1>;
-			vfront-porch = <5>;
-			vback-porch = <32>;
-		};
-	};
-
 	pinmux@70000868 {
 		state_default: pinmux {
 			lcd_dc1_pd2 {
@@ -145,4 +131,18 @@
 			firmware-gpios = <&gpio TEGRA_GPIO(R, 3) GPIO_ACTIVE_HIGH>;
 		};
 	};
+
+	display-panel {
+		panel-timing {
+			clock-frequency = <68000000>;
+			hactive = <800>;
+			vactive = <1280>;
+			hfront-porch = <24>;
+			hback-porch = <32>;
+			hsync-len = <24>;
+			vsync-len = <1>;
+			vfront-porch = <5>;
+			vback-porch = <32>;
+		};
+	};
 };
diff --git a/arch/arm/boot/dts/tegra30-asus-nexus7-tilapia-E1565.dts b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-tilapia-E1565.dts
index f1c63feb4af9..f1c63feb4af9 100644
--- a/arch/arm/boot/dts/tegra30-asus-nexus7-tilapia-E1565.dts
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-tilapia-E1565.dts
diff --git a/arch/arm/boot/dts/tegra30-asus-nexus7-tilapia-memory-timings.dtsi b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-tilapia-memory-timings.dtsi
index 9169de34fa00..9169de34fa00 100644
--- a/arch/arm/boot/dts/tegra30-asus-nexus7-tilapia-memory-timings.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-tilapia-memory-timings.dtsi
diff --git a/arch/arm/boot/dts/tegra30-asus-nexus7-tilapia.dtsi b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-tilapia.dtsi
index cd63e0ef7445..94c80134574e 100644
--- a/arch/arm/boot/dts/tegra30-asus-nexus7-tilapia.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-nexus7-tilapia.dtsi
@@ -6,26 +6,10 @@
 / {
 	compatible = "asus,tilapia", "asus,grouper", "nvidia,tegra30";
 
-	display-panel {
-		enable-gpios = <&gpio TEGRA_GPIO(V, 6) GPIO_ACTIVE_HIGH>;
-
-		panel-timing {
-			clock-frequency = <81750000>;
-			hactive = <800>;
-			vactive = <1280>;
-			hfront-porch = <64>;
-			hback-porch = <128>;
-			hsync-len = <64>;
-			vsync-len = <1>;
-			vfront-porch = <5>;
-			vback-porch = <2>;
-		};
-	};
-
 	gpio@6000d000 {
 		init-mode-3g-hog {
 			gpio-hog;
-			gpios =	<TEGRA_GPIO(D, 2) GPIO_ACTIVE_HIGH>,
+			gpios = <TEGRA_GPIO(D, 2) GPIO_ACTIVE_HIGH>,
 				<TEGRA_GPIO(C, 6) GPIO_ACTIVE_HIGH>,
 				<TEGRA_GPIO(W, 3) GPIO_ACTIVE_HIGH>,
 				<TEGRA_GPIO(P, 1) GPIO_ACTIVE_HIGH>,
@@ -230,4 +214,20 @@
 			firmware-gpios = <&gpio TEGRA_GPIO(P, 3) GPIO_ACTIVE_HIGH>;
 		};
 	};
+
+	display-panel {
+		enable-gpios = <&gpio TEGRA_GPIO(V, 6) GPIO_ACTIVE_HIGH>;
+
+		panel-timing {
+			clock-frequency = <81750000>;
+			hactive = <800>;
+			vactive = <1280>;
+			hfront-porch = <64>;
+			hback-porch = <128>;
+			hsync-len = <64>;
+			vsync-len = <1>;
+			vfront-porch = <5>;
+			vback-porch = <2>;
+		};
+	};
 };
diff --git a/arch/arm/boot/dts/nvidia/tegra30-asus-p1801-t.dts b/arch/arm/boot/dts/nvidia/tegra30-asus-p1801-t.dts
new file mode 100644
index 000000000000..9241cc269a89
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-p1801-t.dts
@@ -0,0 +1,2087 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+
+#include "tegra30.dtsi"
+#include "tegra30-cpu-opp.dtsi"
+#include "tegra30-cpu-opp-microvolt.dtsi"
+
+/ {
+	model = "Asus Portable AiO P1801-T";
+	compatible = "asus,p1801-t", "nvidia,tegra30";
+	chassis-type = "convertible";
+
+	aliases {
+		mmc0 = &sdmmc4; /* eMMC */
+		mmc1 = &sdmmc1; /* uSD slot */
+		mmc2 = &sdmmc3; /* WiFi */
+
+		rtc0 = &pmic;
+		rtc1 = "/rtc@7000e000";
+
+		display0 = &hdmi;
+
+		serial1 = &uartc; /* Bluetooth */
+		serial2 = &uartb; /* GPS */
+	};
+
+	/*
+	 * The decompressor and also some bootloaders rely on a
+	 * pre-existing /chosen node to be available to insert the
+	 * command line and merge other ATAGS info.
+	 */
+	chosen {};
+
+	firmware {
+		trusted-foundations {
+			compatible = "tlm,trusted-foundations";
+			tlm,version-major = <2>;
+			tlm,version-minor = <8>;
+		};
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		linux,cma@80000000 {
+			compatible = "shared-dma-pool";
+			alloc-ranges = <0x80000000 0x30000000>;
+			size = <0x10000000>;		/* 256MiB */
+			linux,cma-default;
+			reusable;
+		};
+
+		framebuffer@abe01000 {
+			reg = <0xabe01000 (1920 * 1080 * 4)>;
+			no-map;
+		};
+
+		trustzone@bfe00000 {
+			reg = <0xbfe00000 0x200000>;	/* 2MB */
+			no-map;
+		};
+
+		ramoops@fea00000 {
+			compatible = "ramoops";
+			reg = <0xfea00000 0x10000>;	/* 64kB */
+			console-size = <0x8000>;	/* 32kB */
+			record-size = <0x400>;		/*  1kB */
+			ecc-size = <16>;
+		};
+	};
+
+	host1x@50000000 {
+		hdmi: hdmi@54280000 {
+			status = "okay";
+
+			hdmi-supply = <&hdmi_5v0_sys>;
+			pll-supply = <&vdd_1v8_vio>;
+			vdd-supply = <&vdd_3v3_sys>;
+
+			port {
+				hdmi_out: endpoint {
+					remote-endpoint = <&bridge_in>;
+				};
+			};
+		};
+	};
+
+	gpio@6000d000 {
+		init-lpm-in-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(B, 1) GPIO_ACTIVE_HIGH>;
+			input;
+		};
+
+		init-lpm-out-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(K, 7) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>;
+			output-low;
+		};
+
+		tp-vendor-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(R, 6) GPIO_ACTIVE_HIGH>;
+			input;
+		};
+	};
+
+	vde@6001a000 {
+		assigned-clocks = <&tegra_car TEGRA30_CLK_VDE>;
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_P>;
+		assigned-clock-rates = <408000000>;
+	};
+
+	pinmux@70000868 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&state_default>;
+
+		state_default: pinmux {
+			/* SDMMC1 pinmux */
+			sdmmc1-clk {
+				nvidia,pins = "sdmmc1_clk_pz0";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			sdmmc1-cmd {
+				nvidia,pins = "sdmmc1_dat3_py4",
+					      "sdmmc1_dat2_py5",
+					      "sdmmc1_dat1_py6",
+					      "sdmmc1_dat0_py7",
+					      "sdmmc1_cmd_pz1";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			sdmmc1-cd {
+				nvidia,pins = "gmi_iordy_pi5";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			sdmmc1-wp {
+				nvidia,pins = "vi_d11_pt3";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* SDMMC2 pinmux */
+			vi-d1-pd5 {
+				nvidia,pins = "vi_d1_pd5",
+					      "vi_d2_pl0",
+					      "vi_d3_pl1",
+					      "vi_d5_pl3",
+					      "vi_d7_pl5";
+				nvidia,function = "sdmmc2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			vi-d8-pl6 {
+				nvidia,pins = "vi_d8_pl6",
+					      "vi_d9_pl7";
+				nvidia,function = "sdmmc2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+				nvidia,io-reset = <0>;
+			};
+
+			/* SDMMC3 pinmux */
+			sdmmc3-clk {
+				nvidia,pins = "sdmmc3_clk_pa6";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			sdmmc3-cmd {
+				nvidia,pins = "sdmmc3_cmd_pa7",
+					      "sdmmc3_dat0_pb7",
+					      "sdmmc3_dat1_pb6",
+					      "sdmmc3_dat2_pb5",
+					      "sdmmc3_dat3_pb4",
+					      "sdmmc3_dat4_pd1",
+					      "sdmmc3_dat5_pd0",
+					      "sdmmc3_dat6_pd3",
+					      "sdmmc3_dat7_pd4";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* SDMMC4 pinmux */
+			sdmmc4-clk {
+				nvidia,pins = "sdmmc4_clk_pcc4";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			sdmmc4-cmd {
+				nvidia,pins = "sdmmc4_cmd_pt7",
+					      "sdmmc4_dat0_paa0",
+					      "sdmmc4_dat1_paa1",
+					      "sdmmc4_dat2_paa2",
+					      "sdmmc4_dat3_paa3",
+					      "sdmmc4_dat4_paa4",
+					      "sdmmc4_dat5_paa5",
+					      "sdmmc4_dat6_paa6",
+					      "sdmmc4_dat7_paa7";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			sdmmc4-rst-n {
+				nvidia,pins = "sdmmc4_rst_n_pcc3";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			cam-mclk {
+				nvidia,pins = "cam_mclk_pcc0";
+				nvidia,function = "vi_alt3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			drive-sdmmc4 {
+				nvidia,pins = "drive_gma",
+					      "drive_gmb",
+					      "drive_gmc",
+					      "drive_gmd";
+				nvidia,pull-down-strength = <9>;
+				nvidia,pull-up-strength = <9>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+			};
+
+			/* I2C pinmux */
+			gen1-i2c {
+				nvidia,pins = "gen1_i2c_scl_pc4",
+					      "gen1_i2c_sda_pc5";
+				nvidia,function = "i2c1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+			gen2-i2c {
+				nvidia,pins = "gen2_i2c_scl_pt5",
+					      "gen2_i2c_sda_pt6";
+				nvidia,function = "i2c2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+			cam-i2c {
+				nvidia,pins = "cam_i2c_scl_pbb1",
+					      "cam_i2c_sda_pbb2";
+				nvidia,function = "i2c3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+			ddc-i2c {
+				nvidia,pins = "ddc_scl_pv4",
+					      "ddc_sda_pv5";
+				nvidia,function = "i2c4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+			pwr-i2c {
+				nvidia,pins = "pwr_i2c_scl_pz6",
+					      "pwr_i2c_sda_pz7";
+				nvidia,function = "i2cpwr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+			hotplug-i2c {
+				nvidia,pins = "pu4";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* HDMI pinmux */
+			hdmi-cec {
+				nvidia,pins = "hdmi_cec_pee3";
+				nvidia,function = "cec";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+			hdmi-hpd {
+				nvidia,pins = "hdmi_int_pn7";
+				nvidia,function = "hdmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* UART-A */
+			ulpi-data0-po1 {
+				nvidia,pins = "ulpi_data0_po1";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			ulpi-data1-po2 {
+				nvidia,pins = "ulpi_data1_po2";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			ulpi-data5-po6 {
+				nvidia,pins = "ulpi_data5_po6";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			ulpi-data7-po0 {
+				nvidia,pins = "ulpi_data7_po0",
+					      "ulpi_data2_po3",
+					      "ulpi_data3_po4",
+					      "ulpi_data4_po5",
+					      "ulpi_data6_po7";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* UART-B */
+			uartb-txd-rts {
+				nvidia,pins = "uart2_txd_pc2",
+					      "uart2_rts_n_pj6";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			uartb-rxd-cts {
+				nvidia,pins = "uart2_rxd_pc3",
+					      "uart2_cts_n_pj5";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* UART-C */
+			uartc-rxd-cts {
+				nvidia,pins = "uart3_cts_n_pa1",
+					      "uart3_rxd_pw7";
+				nvidia,function = "uartc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			uartc-txd-rts {
+				nvidia,pins = "uart3_rts_n_pc0",
+					      "uart3_txd_pw6";
+				nvidia,function = "uartc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* UART-D */
+			ulpi-nxt-py2 {
+				nvidia,pins = "ulpi_nxt_py2";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			ulpi-clk-py0 {
+				nvidia,pins = "ulpi_clk_py0",
+					      "ulpi_dir_py1",
+					      "ulpi_stp_py3";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* I2S pinmux */
+			dap-i2s0 {
+				nvidia,pins = "dap1_fs_pn0",
+					      "dap1_din_pn1",
+					      "dap1_dout_pn2",
+					      "dap1_sclk_pn3";
+				nvidia,function = "i2s0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			dap-i2s1 {
+				nvidia,pins = "dap2_fs_pa2",
+					      "dap2_sclk_pa3",
+					      "dap2_din_pa4",
+					      "dap2_dout_pa5";
+				nvidia,function = "i2s1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			dap3-fs {
+				nvidia,pins = "dap3_fs_pp0",
+					      "dap3_din_pp1";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			dap3-dout {
+				nvidia,pins = "dap3_dout_pp2",
+					      "dap3_sclk_pp3";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			dap-i2s3 {
+				nvidia,pins = "dap4_fs_pp4",
+					      "dap4_din_pp5",
+					      "dap4_dout_pp6",
+					      "dap4_sclk_pp7";
+				nvidia,function = "i2s3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* sensors pinmux */
+			nct-irq {
+				nvidia,pins = "pcc2";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Asus EC pinmux */
+			ec-irqs {
+				nvidia,pins = "kb_row10_ps2",
+					      "kb_row15_ps7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			ec-reqs {
+				nvidia,pins = "kb_col1_pq1";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* memory type bootstrap */
+			mem-boostraps {
+				nvidia,pins = "gmi_ad4_pg4",
+					      "gmi_ad5_pg5";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* PCI-e pinmux */
+			pex-l2-rst-n {
+				nvidia,pins = "pex_l2_rst_n_pcc6",
+					      "pex_l0_rst_n_pdd1",
+					      "pex_l1_rst_n_pdd5";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			pex-l2-clkreq-n {
+				nvidia,pins = "pex_l2_clkreq_n_pcc7",
+					      "pex_l0_prsnt_n_pdd0",
+					      "pex_l0_clkreq_n_pdd2",
+					      "pex_wake_n_pdd3",
+					      "pex_l1_prsnt_n_pdd4",
+					      "pex_l1_clkreq_n_pdd6",
+					      "pex_l2_prsnt_n_pdd7";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* SPI pinmux */
+			spi1-mosi-px4 {
+				nvidia,pins = "spi1_mosi_px4",
+					      "spi1_sck_px5",
+					      "spi1_cs0_n_px6",
+					      "spi1_miso_px7";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			spi2-cs1-n-pw2 {
+				nvidia,pins = "spi2_cs1_n_pw2";
+				nvidia,function = "spi2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			spi2-sck-px2 {
+				nvidia,pins = "spi2_sck_px2";
+				nvidia,function = "spi2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			gmi-a17-pb0 {
+				nvidia,pins = "gmi_a17_pb0",
+					      "gmi_a16_pj7";
+				nvidia,function = "spi4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			gmi-a18-pb1 {
+				nvidia,pins = "gmi_a18_pb1";
+				nvidia,function = "spi4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			gmi-a19-pk7 {
+				nvidia,pins = "gmi_a19_pk7";
+				nvidia,function = "spi4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Display A pinmux */
+			lcd-pwr0-pb2 {
+				nvidia,pins = "lcd_pwr0_pb2",
+					      "lcd_pclk_pb3",
+					      "lcd_pwr1_pc1",
+					      "lcd_d0_pe0",
+					      "lcd_d1_pe1",
+					      "lcd_d2_pe2",
+					      "lcd_d3_pe3",
+					      "lcd_d4_pe4",
+					      "lcd_d5_pe5",
+					      "lcd_d6_pe6",
+					      "lcd_d7_pe7",
+					      "lcd_d8_pf0",
+					      "lcd_d9_pf1",
+					      "lcd_d10_pf2",
+					      "lcd_d11_pf3",
+					      "lcd_d12_pf4",
+					      "lcd_d13_pf5",
+					      "lcd_d14_pf6",
+					      "lcd_d15_pf7",
+					      "lcd_de_pj1",
+					      "lcd_hsync_pj3",
+					      "lcd_vsync_pj4",
+					      "lcd_d16_pm0",
+					      "lcd_d17_pm1",
+					      "lcd_d18_pm2",
+					      "lcd_d19_pm3",
+					      "lcd_d20_pm4",
+					      "lcd_d21_pm5",
+					      "lcd_d22_pm6",
+					      "lcd_d23_pm7",
+					      "lcd_dc0_pn6",
+					      "lcd_sdin_pz2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			lcd-cs0-n-pn4 {
+				nvidia,pins = "lcd_cs0_n_pn4",
+					      "lcd_sdout_pn5",
+					      "lcd_wr_n_pz3";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			blink {
+				nvidia,pins = "clk_32k_out_pa0";
+				nvidia,function = "blink";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* KBC keys */
+			kb-col0-pq0 {
+				nvidia,pins = "kb_col0_pq0";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			kb-col1-pq1 {
+				nvidia,pins = "kb_row1_pr1",
+					      "kb_row3_pr3",
+					      "kb_row14_ps6";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			kb-col4-pq4 {
+				nvidia,pins = "kb_col4_pq4",
+					      "kb_col5_pq5",
+					      "kb_col7_pq7",
+					      "kb_row2_pr2",
+					      "kb_row4_pr4",
+					      "kb_row5_pr5",
+					      "kb_row12_ps4",
+					      "kb_row13_ps5";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi-wp-n-pc7 {
+				nvidia,pins = "gmi_wp_n_pc7",
+					      "gmi_wait_pi7",
+					      "gmi_cs3_n_pk4";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			gmi-cs0-n-pj0 {
+				nvidia,pins = "gmi_cs0_n_pj0",
+					      "gmi_cs1_n_pj2",
+					      "gmi_cs2_n_pk3";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			vi-pclk-pt0 {
+				nvidia,pins = "vi_pclk_pt0";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+				nvidia,io-reset = <0>;
+			};
+
+			/* GPIO keys pinmux */
+			power-key {
+				nvidia,pins = "pv0";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			vol-keys {
+				nvidia,pins = "kb_col2_pq2",
+					      "kb_col3_pq3";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Bluetooth */
+			bt-shutdown {
+				nvidia,pins = "pu0";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			bt-dev-wake {
+				nvidia,pins = "pu1";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			bt-host-wake {
+				nvidia,pins = "pu6";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pu2 {
+				nvidia,pins = "pu2";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			pu3 {
+				nvidia,pins = "pu3";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			pcc1 {
+				nvidia,pins = "pcc1";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			pv2 {
+				nvidia,pins = "pv2";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			pv3 {
+				nvidia,pins = "pv3";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			vi-vsync-pd6 {
+				nvidia,pins = "vi_vsync_pd6",
+					      "vi_hsync_pd7";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+				nvidia,io-reset = <0>;
+			};
+			vi-d10-pt2 {
+				nvidia,pins = "vi_d10_pt2",
+					      "vi_d0_pt4",
+					      "pbb0";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			kb-row0-pr0 {
+				nvidia,pins = "kb_row0_pr0";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			gmi-ad0-pg0 {
+				nvidia,pins = "gmi_ad0_pg0",
+					      "gmi_ad1_pg1",
+					      "gmi_ad2_pg2",
+					      "gmi_ad3_pg3",
+					      "gmi_ad6_pg6",
+					      "gmi_ad7_pg7",
+					      "gmi_wr_n_pi0",
+					      "gmi_oe_n_pi1",
+					      "gmi_dqs_pi2",
+					      "gmi_adv_n_pk0",
+					      "gmi_clk_pk1";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			gmi-ad13-ph5 {
+				nvidia,pins = "gmi_ad13_ph5";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			gmi-ad10-ph2 {
+				nvidia,pins = "gmi_ad10_ph2",
+					      "gmi_ad11_ph3",
+					      "gmi_ad14_ph6";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			gmi-ad12-ph4 {
+				nvidia,pins = "gmi_ad12_ph4",
+					      "gmi_rst_n_pi4";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* USB2 VBUS control */
+			usb2-vbus-control {
+				nvidia,pins = "gmi_ad15_ph7";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* PWM pinmux */
+			pwm-0 {
+				nvidia,pins = "gmi_ad8_ph0";
+				nvidia,function = "pwm0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			pwm-2 {
+				nvidia,pins = "pu5";
+				nvidia,function = "pwm2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* S/PDIF pinmux */
+			spdif-out {
+				nvidia,pins = "spdif_out_pk5";
+				nvidia,function = "spdif";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			spdif-in {
+				nvidia,pins = "spdif_in_pk6";
+				nvidia,function = "spdif";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			vi-d4-pl2 {
+				nvidia,pins = "vi_d4_pl2";
+				nvidia,function = "vi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			vi-d6-pl4 {
+				nvidia,pins = "vi_d6_pl4";
+				nvidia,function = "vi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+				nvidia,lock = <0>;
+				nvidia,io-reset = <0>;
+			};
+			vi-mclk-pt1 {
+				nvidia,pins = "vi_mclk_pt1";
+				nvidia,function = "vi";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			jtag-rtck {
+				nvidia,pins = "jtag_rtck_pu7";
+				nvidia,function = "rtck";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			crt-hsync-pv6 {
+				nvidia,pins = "crt_hsync_pv6",
+					      "crt_vsync_pv7";
+				nvidia,function = "crt";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			clk1-out {
+				nvidia,pins = "clk1_out_pw4";
+				nvidia,function = "extperiph1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			clk2-out {
+				nvidia,pins = "clk2_out_pw5";
+				nvidia,function = "extperiph2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			clk3-out {
+				nvidia,pins = "clk3_out_pee0";
+				nvidia,function = "extperiph3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			sys-clk-req {
+				nvidia,pins = "sys_clk_req_pz5";
+				nvidia,function = "sysclk";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			pbb4 {
+				nvidia,pins = "pbb4";
+				nvidia,function = "vgp4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			pbb5 {
+				nvidia,pins = "pbb5";
+				nvidia,function = "vgp5";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			pbb6 {
+				nvidia,pins = "pbb6";
+				nvidia,function = "vgp6";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			clk2-req-pcc5 {
+				nvidia,pins = "clk2_req_pcc5",
+					      "clk1_req_pee2";
+				nvidia,function = "dap";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			clk3-req-pee1 {
+				nvidia,pins = "clk3_req_pee1";
+				nvidia,function = "dev3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			owr {
+				nvidia,pins = "owr";
+				nvidia,function = "owr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* P1801-T specific pinmux */
+			lcd-pwr2 {
+				nvidia,pins = "lcd_pwr2_pc6",
+					      "lcd_dc1_pd2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			lcd-m1 {
+				nvidia,pins = "lcd_m1_pw1";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			key-mode {
+				nvidia,pins = "gmi_cs4_n_pk2";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			splashtop {
+				nvidia,pins = "gmi_cs6_n_pi3";
+				nvidia,function = "nand_alt";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			w8-detect {
+				nvidia,pins = "gmi_cs7_n_pi6";
+				nvidia,function = "nand_alt";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			pbb3 {
+				nvidia,pins = "pbb3";
+				nvidia,function = "vgp3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			pbb7 {
+				nvidia,pins = "pbb7";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			spi2-mosi-px0 {
+				nvidia,pins = "spi2_mosi_px0";
+				nvidia,function = "spi6";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			tp-vendor {
+				nvidia,pins = "kb_row6_pr6",
+					      "kb_row7_pr7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			tp-power {
+				nvidia,pins = "kb_row8_ps0";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* GPIO power/drive control */
+			drive-dap1 {
+				nvidia,pins = "drive_dap1",
+					      "drive_dap2",
+					      "drive_dbg",
+					      "drive_at5",
+					      "drive_gme",
+					      "drive_ddc",
+					      "drive_ao1",
+					      "drive_uart3";
+				nvidia,high-speed-mode = <TEGRA_PIN_DISABLE>;
+				nvidia,schmitt = <TEGRA_PIN_ENABLE>;
+				nvidia,low-power-mode = <TEGRA_PIN_LP_DRIVE_DIV_1>;
+				nvidia,pull-down-strength = <31>;
+				nvidia,pull-up-strength = <31>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+			};
+			drive-sdio1 {
+				nvidia,pins = "drive_sdio1",
+					      "drive_sdio3";
+				nvidia,high-speed-mode = <TEGRA_PIN_DISABLE>;
+				nvidia,schmitt = <TEGRA_PIN_DISABLE>;
+				nvidia,pull-down-strength = <46>;
+				nvidia,pull-up-strength = <42>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FAST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FAST>;
+			};
+		};
+	};
+
+	uartb: serial@70006040 {
+		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
+		status = "okay";
+
+		/* Broadcom GPS BCM47511 */
+	};
+
+	uartc: serial@70006200 {
+		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
+		status = "okay";
+
+		/* Azurewave AW-AH691 BCM43241B0 */
+	};
+
+	pwm: pwm@7000a000 {
+		status = "okay";
+	};
+
+	i2c@7000c000 {
+		status = "okay";
+		clock-frequency = <280000>;
+	};
+
+	i2c@7000c400 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		/* Nuvoton NPCE791LA0DX embedded controller */
+	};
+
+	i2c@7000c500 {
+		status = "okay";
+		clock-frequency = <100000>;
+
+		accelerometer@f {
+			compatible = "kionix,kxtf9";
+			reg = <0x0f>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(O, 5) IRQ_TYPE_EDGE_RISING>;
+
+			vdd-supply = <&vdd_1v8_vio>;
+			vddio-supply = <&vdd_1v8_vio>;
+
+			mount-matrix = "0", "1", "0",
+				       "1", "0", "0",
+				       "0", "0", "1";
+		};
+	};
+
+	hdmi_ddc: i2c@7000c700 {
+		status = "okay";
+		clock-frequency = <33000>;
+	};
+
+	i2c@7000d000 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		rt5640: audio-codec@1c {
+			compatible = "realtek,rt5640";
+			reg = <0x1c>;
+
+			realtek,dmic1-data-pin = <1>;
+
+			clocks = <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+			clock-names = "mclk";
+
+			realtek,ldo1-en-gpios = <&gpio TEGRA_GPIO(BB, 6) GPIO_ACTIVE_HIGH>;
+		};
+
+		/* Texas Instruments TPS659110 PMIC */
+		pmic: pmic@2d {
+			compatible = "ti,tps65911";
+			reg = <0x2d>;
+
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			wakeup-source;
+
+			ti,en-gpio-sleep = <0 0 1 0 0 0 0 0 0>;
+			ti,system-power-controller;
+			ti,sleep-keep-ck32k;
+			ti,sleep-enable;
+
+			#gpio-cells = <2>;
+			gpio-controller;
+
+			vcc1-supply = <&vdd_5v0_bat>;
+			vcc2-supply = <&vdd_5v0_bat>;
+			vcc3-supply = <&vdd_1v8_vio>;
+			vcc4-supply = <&vdd_5v0_bat>;
+			vcc5-supply = <&vdd_5v0_bat>;
+			vcc6-supply = <&vddio_ddr>;
+			vcc7-supply = <&vdd_5v0_bat>;
+			vccio-supply = <&vdd_5v0_bat>;
+
+			pmic-sleep-hog {
+				gpio-hog;
+				gpios = <2 GPIO_ACTIVE_HIGH>;
+				output-high;
+			};
+
+			regulators {
+				/* vdd1 is not used by Portable AiO */
+
+				vddio_ddr: vdd2 {
+					regulator-name = "vddio_ddr";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				vdd_cpu: vddctrl {
+					regulator-name = "vdd_cpu,vdd_sys";
+					regulator-min-microvolt = <600000>;
+					regulator-max-microvolt = <1400000>;
+					regulator-coupled-with = <&vdd_core>;
+					regulator-coupled-max-spread = <300000>;
+					regulator-max-step-microvolt = <100000>;
+					regulator-always-on;
+					regulator-boot-on;
+					ti,regulator-ext-sleep-control = <1>;
+
+					nvidia,tegra-cpu-regulator;
+				};
+
+				vdd_1v8_vio: vio {
+					regulator-name = "vdd_1v8_gen";
+					regulator-min-microvolt = <1500000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				/* eMMC VDD */
+				vcore_emmc: ldo1 {
+					regulator-name = "vdd_emmc_core";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+				};
+
+				/* uSD slot VDD */
+				vdd_usd: ldo2 {
+					regulator-name = "vdd_usd";
+					regulator-min-microvolt = <3100000>;
+					regulator-max-microvolt = <3100000>;
+					regulator-always-on;
+				};
+
+				/* uSD slot VDDIO */
+				vddio_usd: ldo3 {
+					regulator-name = "vddio_usd";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <3100000>;
+				};
+
+				ldo4 {
+					regulator-name = "vdd_rtc";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+				};
+
+				/* ldo5 is not used by Portable AiO */
+
+				ldo6 {
+					regulator-name = "avdd_dsi_csi,pwrdet_mipi";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+				};
+
+				ldo7 {
+					regulator-name = "vdd_pllm,x,u,a_p_c_s";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+					ti,regulator-ext-sleep-control = <8>;
+				};
+
+				ldo8 {
+					regulator-name = "vdd_ddr_hs";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+					ti,regulator-ext-sleep-control = <8>;
+				};
+			};
+		};
+
+		nct72: temperature-sensor@4c {
+			compatible = "onnn,nct1008";
+			reg = <0x4c>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(CC, 2) IRQ_TYPE_EDGE_FALLING>;
+
+			vcc-supply = <&vdd_3v3_sys>;
+			#thermal-sensor-cells = <1>;
+		};
+
+		vdd_core: core-regulator@60 {
+			compatible = "ti,tps62361";
+			reg = <0x60>;
+
+			regulator-name = "tps62361-vout";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1770000>;
+			regulator-coupled-with = <&vdd_cpu>;
+			regulator-coupled-max-spread = <300000>;
+			regulator-max-step-microvolt = <100000>;
+			regulator-boot-on;
+			regulator-always-on;
+			ti,enable-vout-discharge;
+			ti,vsel0-state-high;
+			ti,vsel1-state-high;
+
+			nvidia,tegra-core-regulator;
+		};
+	};
+
+	vdd_5v0_bat: regulator-bat {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_ac_bat";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_5v0_cp: regulator-sby {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0_sby";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&pmic 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_bat>;
+	};
+
+	vdd_5v0_sys: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&pmic 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_bat>;
+	};
+
+	vdd_1v5_ddr: regulator-ddr {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_ddr";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&pmic 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_bat>;
+	};
+
+	vdd_3v3_sys: regulator-3v {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3_sys";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&pmic 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_bat>;
+	};
+
+	vdd_3v3_com: regulator-com {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3_com";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		gpio = <&gpio TEGRA_GPIO(D, 0) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_sys>;
+	};
+
+	usb2_vbus: regulator-usb2 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb2_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_HIGH>;
+		gpio-open-drain;
+		vin-supply = <&vdd_5v0_sys>;
+	};
+
+	hdmi_5v0_sys: regulator-hdmi {
+		compatible = "regulator-fixed";
+		regulator-name = "hdmi_5v0_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_sys>;
+	};
+
+	pmc@7000e400 {
+		status = "okay";
+		nvidia,invert-interrupt;
+		nvidia,suspend-mode = <2>;
+		nvidia,cpu-pwr-good-time = <2000>;
+		nvidia,cpu-pwr-off-time = <200>;
+		nvidia,core-pwr-good-time = <3845 3845>;
+		nvidia,core-pwr-off-time = <0>;
+		nvidia,core-power-req-active-high;
+		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
+
+		i2c-thermtrip {
+			nvidia,i2c-controller-id = <4>;
+			nvidia,bus-addr = <0x2d>;
+			nvidia,reg-addr = <0x3f>;
+			nvidia,reg-data = <0x81>;
+		};
+	};
+
+	memory-controller@7000f000 {
+		emc-timings-3 {
+			/* Micron 2GB 800MHz */
+			nvidia,ram-code = <3>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00030003 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x75830303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010003 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x74630303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000030
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0503 0x73c30504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000006 0xc0000025
+					0x00000001 0x00000001 0x00000005 0x00000002
+					0x00000003 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0505 0x73840a06 0x001f0000 >;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+
+				nvidia,emem-configuration = < 0x0000000c 0xc0000048
+					0x00000001 0x00000002 0x00000009 0x00000005
+					0x00000005 0x00000001 0x00000002 0x00000008
+					0x00000002 0x00000002 0x00000003 0x00000006
+					0x06030202 0x000d0709 0x7086120a 0x001f0000 >;
+			};
+
+			timing-800000000 {
+				clock-frequency = <800000000>;
+
+				nvidia,emem-configuration = < 0x00000018 0xc0000090
+					0x00000004 0x00000005 0x00000013 0x0000000c
+					0x0000000b 0x00000002 0x00000003 0x0000000c
+					0x00000002 0x00000002 0x00000004 0x00000008
+					0x08040202 0x00160d13 0x712c2414 0x001f0000 >;
+			};
+		};
+	};
+
+	memory-controller@7000f400 {
+		emc-timings-3 {
+			/* Micron 2GB 800MHz */
+			nvidia,ram-code = <3>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000006 0x00000000 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x00000009
+					0x0000000b 0x000000c0 0x00000000 0x00000030
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000007 0x00000007
+					0x00000004 0x00000001 0x00000000 0x00000004
+					0x00000005 0x000000c7 0x00000006 0x00000006
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000002
+					0x0000000d 0x00000001 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x00000009
+					0x0000000b 0x00000181 0x00000000 0x00000060
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x0000000e 0x0000000e
+					0x00000004 0x00000002 0x00000000 0x00000004
+					0x00000005 0x0000018e 0x00000006 0x00000006
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000004
+					0x0000001a 0x00000003 0x00000001 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000001
+					0x00000001 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x00000009
+					0x0000000b 0x00000303 0x00000000 0x000000c0
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x0000001c 0x0000001c
+					0x00000004 0x00000004 0x00000000 0x00000004
+					0x00000005 0x0000031c 0x00000006 0x00000006
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000009
+					0x00000035 0x00000007 0x00000002 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000002
+					0x00000002 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000006 0x00000004 0x00000009
+					0x0000000b 0x00000607 0x00000000 0x00000181
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000038 0x00000038
+					0x00000004 0x00000007 0x00000000 0x00000004
+					0x00000005 0x00000638 0x00000007 0x00000004
+					0x00000000 0x00000000 0x00004288 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00020000
+					0x00000100 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000d22 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200000>;
+				nvidia,emc-mode-reset = <0x80000521>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+
+				nvidia,emc-configuration =  < 0x00000012
+					0x00000066 0x0000000c 0x00000004 0x00000003
+					0x00000008 0x00000002 0x0000000a 0x00000004
+					0x00000004 0x00000002 0x00000001 0x00000000
+					0x00000004 0x00000006 0x00000004 0x0000000a
+					0x0000000c 0x00000bf0 0x00000000 0x000002fc
+					0x00000001 0x00000008 0x00000001 0x00000000
+					0x00000008 0x0000000f 0x0000006c 0x00000200
+					0x00000004 0x0000000c 0x00000000 0x00000004
+					0x00000005 0x00000c30 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00007088 0x001d0084
+					0x00008000 0x00044000 0x00044000 0x00044000
+					0x00044000 0x00044000 0x00044000 0x00044000
+					0x00044000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00048000 0x00048000 0x00048000
+					0x00048000 0x000002a0 0x0800013d 0x00000000
+					0x77fff884 0x01f1f508 0x05057404 0x54000007
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x0158000c 0xa0f10000 0x00000000
+					0x00000000 0x800018c8 0xe8000000 0xff00ff89 >;
+			};
+
+			timing-800000000 {
+				clock-frequency = <800000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200018>;
+				nvidia,emc-mode-reset = <0x80000d71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000025
+					0x000000ce 0x0000001a 0x00000009 0x00000005
+					0x0000000d 0x00000004 0x00000013 0x00000009
+					0x00000009 0x00000003 0x00000001 0x00000000
+					0x00000007 0x0000000b 0x00000009 0x0000000b
+					0x00000012 0x00001820 0x00000000 0x00000608
+					0x00000003 0x00000012 0x00000001 0x00000000
+					0x0000000f 0x00000018 0x000000d8 0x00000200
+					0x00000005 0x00000018 0x00000000 0x00000007
+					0x00000008 0x00001860 0x0000000c 0x00000004
+					0x00000000 0x00000000 0x00005088 0xf0070191
+					0x00008000 0x0000c00a 0x0000000a 0x0000000a
+					0x0000000a 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00018000 0x00018000 0x00018000
+					0x00018000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x000002a0 0x0800013d 0x22220000
+					0x77fff884 0x01f1f501 0x07077404 0x54000000
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x00f0000c 0xa0f10202 0x00000000
+					0x00000000 0x8000308c 0xe8000000 0xff00ff49 >;
+			};
+		};
+	};
+
+	hda@70030000 {
+		status = "okay";
+	};
+
+	ahub@70080000 {
+		i2s@70080400 { /* i2s1 */
+			status = "okay";
+		};
+
+		/* BT SCO */
+		i2s@70080600 { /* i2s3 */
+			status = "okay";
+		};
+	};
+
+	sdmmc1: mmc@78000000 {
+		status = "okay";
+
+		/* SDR104 mode unsupported yet */
+		max-frequency = <104000000>;
+
+		cd-gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
+		bus-width = <4>;
+
+		vmmc-supply = <&vdd_usd>;	/* ldo2 */
+		vqmmc-supply = <&vddio_usd>;	/* ldo3 */
+	};
+
+	sdmmc3: mmc@78000400 {
+		status = "okay";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		keep-power-in-suspend;
+		bus-width = <4>;
+		non-removable;
+
+		mmc-pwrseq = <&brcm_wifi_pwrseq>;
+		vmmc-supply = <&vdd_3v3_com>;
+		vqmmc-supply = <&vdd_1v8_vio>;
+
+		/* Azurewave AW-AH691 BCM43241B0 */
+		wifi@1 {
+			compatible = "brcm,bcm4329-fmac";
+			reg = <1>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(O, 4) IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "host-wake";
+		};
+	};
+
+	sdmmc4: mmc@78000600 {
+		status = "okay";
+		bus-width = <8>;
+
+		non-removable;
+		mmc-ddr-3_3v;
+
+		vmmc-supply = <&vcore_emmc>;
+		vqmmc-supply = <&vdd_1v8_vio>;
+	};
+
+	/* USB via ASUS connector */
+	usb@7d000000 {
+		compatible = "nvidia,tegra30-udc";
+		status = "okay";
+		dr_mode = "peripheral";
+	};
+
+	usb-phy@7d000000 {
+		status = "okay";
+		dr_mode = "peripheral";
+		nvidia,hssync-start-delay = <0>;
+		nvidia,xcvr-lsfslew = <2>;
+		nvidia,xcvr-lsrslew = <2>;
+		vbus-supply = <&vdd_5v0_sys>;
+	};
+
+	/* mini-USB port */
+	usb@7d004000 {
+		status = "okay";
+	};
+
+	usb-phy@7d004000 {
+		status = "okay";
+		vbus-supply = <&usb2_vbus>;
+	};
+
+	/* Full size USB */
+	usb@7d008000 {
+		status = "okay";
+	};
+
+	usb-phy@7d008000 {
+		status = "okay";
+		vbus-supply = <&vdd_5v0_bat>;
+	};
+
+	pad_battery: battery-cell {
+		compatible = "simple-battery";
+		device-chemistry = "lithium-ion-polymer";
+		charge-full-design-microamp-hours = <5136000>;
+		energy-full-design-microwatt-hours = <38000000>;
+		operating-range-celsius = <0 45>;
+	};
+
+	/* Connected to a 18.4" LVDS panel */
+	bridge {
+		compatible = "mstar,tsumu88adt3-lf-1";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				bridge_in: endpoint {
+					remote-endpoint = <&hdmi_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				bridge_out: endpoint {
+					remote-endpoint = <&hdmi_connector_in>;
+				};
+			};
+		};
+	};
+
+	/* PMIC has a built-in 32KHz oscillator which is used by PMC */
+	clk32k_in: clock-32k {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "pmic-oscillator";
+	};
+
+	connector {
+		compatible = "hdmi-connector";
+		label = "HDMI";
+		type = "a";
+
+		/* low: tablet, high: dock */
+		hpd-gpios = <&gpio TEGRA_GPIO(H, 4) GPIO_ACTIVE_LOW>;
+		ddc-i2c-bus = <&hdmi_ddc>;
+		ddc-en-gpios = <&gpio TEGRA_GPIO(H, 3) GPIO_ACTIVE_HIGH>;
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&bridge_out>;
+			};
+		};
+	};
+
+	cpus {
+		cpu0: cpu@0 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+		cpu1: cpu@1 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+		cpu2: cpu@2 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+		cpu3: cpu@3 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-power {
+			label = "Power";
+			gpios = <&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio TEGRA_GPIO(Q, 2) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio TEGRA_GPIO(Q, 3) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		switch-docking-station-mode {
+			label = "Mode";
+			gpios = <&gpio TEGRA_GPIO(K, 2) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_MODE>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+	};
+
+	opp-table-actmon {
+		opp-800000000 {
+			opp-supported-hw = <0x0006>;
+		};
+
+		/delete-node/ opp-900000000;
+	};
+
+	opp-table-emc {
+		opp-800000000-1300 {
+			opp-supported-hw = <0x0006>;
+		};
+
+		/delete-node/ opp-900000000-1350;
+	};
+
+	brcm_wifi_pwrseq: pwrseq-wifi {
+		compatible = "mmc-pwrseq-simple";
+
+		clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
+		clock-names = "ext_clock";
+
+		reset-gpios = <&gpio TEGRA_GPIO(D, 4) GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <300>;
+		power-off-delay-us = <300>;
+	};
+
+	sound {
+		compatible = "asus,tegra-audio-rt5640-p1801-t",
+			     "nvidia,tegra-audio-rt5640";
+		nvidia,model = "Asus Portable AiO P1801-T RT5642";
+
+		nvidia,audio-routing =
+			"Headphones", "HPOR",
+			"Headphones", "HPOL",
+			"Speakers", "SPORP",
+			"Speakers", "SPORN",
+			"Speakers", "SPOLP",
+			"Speakers", "SPOLN",
+			"DMIC1", "Mic Jack";
+
+		nvidia,i2s-controller = <&tegra_i2s1>;
+		nvidia,audio-codec = <&rt5640>;
+
+		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_LOW>;
+
+		clocks = <&tegra_car TEGRA30_CLK_PLL_A>,
+			 <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
+			 <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+		clock-names = "pll_a", "pll_a_out0", "mclk";
+
+		assigned-clocks = <&tegra_car TEGRA30_CLK_EXTERN1>,
+				  <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
+					 <&tegra_car TEGRA30_CLK_EXTERN1>;
+	};
+
+	thermal-zones {
+		/*
+		 * NCT72 has two sensors:
+		 *
+		 *	0: internal that monitors ambient/skin temperature
+		 *	1: external that is connected to the CPU's diode
+		 *
+		 * Ideally we should use userspace thermal governor,
+		 * but it's a much more complex solution. The "skin"
+		 * zone exists as a simpler solution which prevents
+		 * the Portable AiO from getting too hot from a user's
+		 * tactile perspective. The CPU zone is intended to
+		 * protect silicon from damage.
+		 */
+
+		skin-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct72 0>;
+
+			trips {
+				trip0: skin-alert {
+					/* throttle at 57C until temperature drops to 56.8C */
+					temperature = <57000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip1: skin-crit {
+					/* shut down at 65C */
+					temperature = <65000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&trip0>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&actmon THERMAL_NO_LIMIT
+								  THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		cpu-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct72 1>;
+
+			trips {
+				trip2: cpu-alert {
+					/* throttle at 75C until temperature drops to 74.8C */
+					temperature = <75000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip3: cpu-crit {
+					/* shut down at 90C */
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map1 {
+					trip = <&trip2>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&actmon THERMAL_NO_LIMIT
+								  THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/tegra30-asus-tf201.dts b/arch/arm/boot/dts/nvidia/tegra30-asus-tf201.dts
index 315c6dc068c5..0406c5a69c12 100644
--- a/arch/arm/boot/dts/tegra30-asus-tf201.dts
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-tf201.dts
@@ -605,23 +605,40 @@
 		enable-gpios = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_HIGH>;
 		vcc-supply = <&vdd_3v3_sys>;
 	};
-};
 
-&emc_icc_dvfs_opp_table {
-	/delete-node/ opp-533000000-1200;
-	/delete-node/ opp-625000000-1200;
-	/delete-node/ opp-625000000-1250;
-	/delete-node/ opp-667000000-1200;
-	/delete-node/ opp-750000000-1300;
-	/delete-node/ opp-800000000-1300;
-	/delete-node/ opp-900000000-1350;
-};
+	opp-table-actmon {
+		/delete-node/ opp-533000000;
+		/delete-node/ opp-625000000;
+		/delete-node/ opp-667000000;
+		/delete-node/ opp-750000000;
+		/delete-node/ opp-800000000;
+		/delete-node/ opp-900000000;
+	};
 
-&emc_bw_dfs_opp_table {
-	/delete-node/ opp-533000000;
-	/delete-node/ opp-625000000;
-	/delete-node/ opp-667000000;
-	/delete-node/ opp-750000000;
-	/delete-node/ opp-800000000;
-	/delete-node/ opp-900000000;
+	opp-table-emc {
+		/delete-node/ opp-533000000-1200;
+		/delete-node/ opp-625000000-1200;
+		/delete-node/ opp-625000000-1250;
+		/delete-node/ opp-667000000-1200;
+		/delete-node/ opp-750000000-1300;
+		/delete-node/ opp-800000000-1300;
+		/delete-node/ opp-900000000-1350;
+	};
+
+	sound {
+		compatible = "asus,tegra-audio-rt5631-tf201",
+			     "nvidia,tegra-audio-rt5631";
+		nvidia,model = "Asus Transformer Prime TF201 RT5631";
+
+		nvidia,audio-routing =
+			"Headphone Jack", "HPOL",
+			"Headphone Jack", "HPOR",
+			"Int Spk", "SPOL",
+			"Int Spk", "SPOR",
+			"MIC1", "MIC Bias1",
+			"MIC Bias1", "Mic Jack",
+			"DMIC", "Int Mic";
+
+		nvidia,audio-codec = <&rt5631>;
+	};
 };
diff --git a/arch/arm/boot/dts/tegra30-asus-tf300t.dts b/arch/arm/boot/dts/nvidia/tegra30-asus-tf300t.dts
index f47434871a5c..970a1f08dc8c 100644
--- a/arch/arm/boot/dts/tegra30-asus-tf300t.dts
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-tf300t.dts
@@ -128,8 +128,8 @@
 			micdet-delay = <100>;
 
 			gpio-cfg = <
-				0xffffffff /* don't touch */
-				0xffffffff /* don't touch */
+				0x00000600 /* DMIC_LR, output */
+				0x00000680 /* DMIC_DAT, input */
 				0x00000000 /* Speaker-enable GPIO, output, low */
 				0xffffffff /* don't touch */
 				0xffffffff /* don't touch */
@@ -999,6 +999,18 @@
 		compatible = "innolux,g101ice-l01";
 	};
 
+	opp-table-emc {
+		/delete-node/ opp-750000000-1300;
+		/delete-node/ opp-800000000-1300;
+		/delete-node/ opp-900000000-1350;
+	};
+
+	opp-table-actmon {
+		/delete-node/ opp-750000000;
+		/delete-node/ opp-800000000;
+		/delete-node/ opp-900000000;
+	};
+
 	sound {
 		compatible = "asus,tegra-audio-wm8903-tf300t",
 			     "nvidia,tegra-audio-wm8903";
@@ -1011,24 +1023,10 @@
 			"Int Spk", "RON",
 			"Int Spk", "LOP",
 			"Int Spk", "LON",
-			"IN1L", "Mic Jack",
 			"IN2L", "Mic Jack",
 			"DMICDAT", "Int Mic";
 
 		nvidia,audio-codec = <&wm8903>;
 		nvidia,spkr-en-gpios = <&wm8903 2 GPIO_ACTIVE_HIGH>;
-		nvidia,headset;
 	};
 };
-
-&emc_icc_dvfs_opp_table {
-	/delete-node/ opp-750000000-1300;
-	/delete-node/ opp-800000000-1300;
-	/delete-node/ opp-900000000-1350;
-};
-
-&emc_bw_dfs_opp_table {
-	/delete-node/ opp-750000000;
-	/delete-node/ opp-800000000;
-	/delete-node/ opp-900000000;
-};
diff --git a/arch/arm/boot/dts/tegra30-asus-tf300tg.dts b/arch/arm/boot/dts/nvidia/tegra30-asus-tf300tg.dts
index 96345f821c3d..4861db8e1e59 100644
--- a/arch/arm/boot/dts/tegra30-asus-tf300tg.dts
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-tf300tg.dts
@@ -1072,16 +1072,33 @@
 	display-panel {
 		compatible = "innolux,g101ice-l01";
 	};
-};
 
-&emc_icc_dvfs_opp_table {
-	/delete-node/ opp-750000000-1300;
-	/delete-node/ opp-800000000-1300;
-	/delete-node/ opp-900000000-1350;
-};
+	opp-table-emc {
+		/delete-node/ opp-750000000-1300;
+		/delete-node/ opp-800000000-1300;
+		/delete-node/ opp-900000000-1350;
+	};
 
-&emc_bw_dfs_opp_table {
-	/delete-node/ opp-750000000;
-	/delete-node/ opp-800000000;
-	/delete-node/ opp-900000000;
+	opp-table-actmon {
+		/delete-node/ opp-750000000;
+		/delete-node/ opp-800000000;
+		/delete-node/ opp-900000000;
+	};
+
+	sound {
+		compatible = "asus,tegra-audio-rt5631-tf300tg",
+			     "nvidia,tegra-audio-rt5631";
+		nvidia,model = "Asus Transformer Pad TF300TG RT5631";
+
+		nvidia,audio-routing =
+			"Headphone Jack", "HPOL",
+			"Headphone Jack", "HPOR",
+			"Int Spk", "SPOL",
+			"Int Spk", "SPOR",
+			"MIC1", "MIC Bias1",
+			"MIC Bias1", "Mic Jack",
+			"DMIC", "Int Mic";
+
+		nvidia,audio-codec = <&rt5631>;
+	};
 };
diff --git a/arch/arm/boot/dts/nvidia/tegra30-asus-tf300tl.dts b/arch/arm/boot/dts/nvidia/tegra30-asus-tf300tl.dts
new file mode 100644
index 000000000000..2ef9d8737901
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-tf300tl.dts
@@ -0,0 +1,857 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "tegra30-asus-transformer-common.dtsi"
+#include "tegra30-asus-lvds-display.dtsi"
+
+/ {
+	model = "Asus Transformer Pad LTE TF300TL";
+	compatible = "asus,tf300tl", "nvidia,tegra30";
+
+	gpio@6000d000 {
+		tf300tl-init-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(C, 6) GPIO_ACTIVE_HIGH>;
+			output-low;
+		};
+	};
+
+	pinmux@70000868 {
+		state_default: pinmux {
+			lcd_pwr2_pc6 {
+				nvidia,pins = "lcd_pwr2_pc6",
+					      "lcd_dc1_pd2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pbb3 {
+				nvidia,pins = "pbb3";
+				nvidia,function = "vgp3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pbb7 {
+				nvidia,pins = "pbb7";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			kb_row7_pr7 {
+				nvidia,pins = "kb_row7_pr7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_cs4_n_pk2 {
+				nvidia,pins = "gmi_cs4_n_pk2";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ulpi_data5_po6 {
+				nvidia,pins = "ulpi_data5_po6";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap3_din_pp1 {
+				nvidia,pins = "dap3_din_pp1";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			crt_hsync_pv6 {
+				nvidia,pins = "crt_hsync_pv6";
+				nvidia,function = "crt";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			crt_vsync_pv7 {
+				nvidia,pins = "crt_vsync_pv7";
+				nvidia,function = "crt";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pu5 {
+				nvidia,pins = "pu5";
+				nvidia,function = "pwm2";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			clk3_out_pee0 {
+				nvidia,pins = "clk3_out_pee0";
+				nvidia,function = "extperiph3";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			clk3_req_pee1 {
+				nvidia,pins = "clk3_req_pee1";
+				nvidia,function = "dev3";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			dap1_fs_pn0 {
+				nvidia,pins = "dap1_fs_pn0",
+						"dap1_sclk_pn3";
+				nvidia,function = "i2s0";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			dap1_din_pn1 {
+				nvidia,pins = "dap1_din_pn1";
+				nvidia,function = "i2s0";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap1_dout_pn2 {
+				nvidia,pins = "dap1_dout_pn2";
+				nvidia,function = "i2s0";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			clk1_req_pee2 {
+				nvidia,pins = "clk1_req_pee2";
+				nvidia,function = "dap";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spi2_mosi_px0 {
+				nvidia,pins = "spi2_mosi_px0";
+				nvidia,function = "spi2";
+			};
+
+			spi1_sck_px5 {
+				nvidia,pins = "spi1_sck_px5";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			spi1_miso_px7 {
+				nvidia,pins = "spi1_miso_px7";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			spi2_cs2_n_pw3 {
+				nvidia,pins = "spi2_cs2_n_pw3";
+				nvidia,function = "spi2";
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+			};
+		};
+	};
+
+	serial@70006200 {
+		/* Azurewave AW-NH615 BCM4329B1 */
+		bluetooth {
+			compatible = "brcm,bcm4329-bt";
+		};
+	};
+
+	i2c@7000c400 {
+		/* Elantech EKTH1036 touchscreen */
+		touchscreen@10 {
+			compatible = "elan,ektf3624";
+			reg = <0x10>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(H, 4) IRQ_TYPE_EDGE_FALLING>;
+			reset-gpios = <&gpio TEGRA_GPIO(H, 6) GPIO_ACTIVE_LOW>;
+
+			vcc33-supply = <&vdd_3v3_sys>;
+			vccio-supply = <&vdd_3v3_sys>;
+
+			touchscreen-size-x = <2240>;
+			touchscreen-size-y = <1408>;
+			touchscreen-inverted-y;
+		};
+	};
+
+	i2c@7000c500 {
+		clock-frequency = <400000>;
+
+		magnetometer@e {
+			mount-matrix =  "-1",  "0",  "0",
+					 "0", "-1",  "0",
+					 "0",  "0",  "1";
+		};
+
+		gyroscope@68 {
+			mount-matrix =   "-1",  "0",  "0",
+					  "0",  "1",  "0",
+					  "0",  "0", "-1";
+
+			/* External I2C interface */
+			i2c-gate {
+				accelerometer@f {
+					mount-matrix =   "0", "-1",  "0",
+							"-1",  "0",  "0",
+							 "0",  "0",  "1";
+				};
+			};
+		};
+	};
+
+	i2c@7000d000 {
+		/* Realtek ALC5631 audio codec */
+		rt5631: audio-codec@1a {
+			compatible = "realtek,rt5631";
+			reg = <0x1a>;
+		};
+	};
+
+	memory-controller@7000f000 {
+		emc-timings-0 {
+			/* Elpida 1GB 667MHZ */
+			nvidia,ram-code = <0>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x74830303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x73430303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0xc0000030
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0503 0x72830504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000025
+					0x00000001 0x00000001 0x00000005 0x00000002
+					0x00000003 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0505 0x72440a06 0x001f0000 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emem-configuration = < 0x00000005 0xc000003d
+					0x00000001 0x00000002 0x00000008 0x00000004
+					0x00000004 0x00000001 0x00000002 0x00000007
+					0x00000002 0x00000002 0x00000003 0x00000006
+					0x06030202 0x000b0608 0x70850f09 0x001f0000 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emem-configuration = < 0x0000000a 0xc0000079
+					0x00000003 0x00000004 0x00000010 0x0000000b
+					0x0000000a 0x00000001 0x00000003 0x0000000b
+					0x00000002 0x00000002 0x00000004 0x00000008
+					0x08040202 0x00130b10 0x70ea1f11 0x001f0000 >;
+			};
+		};
+
+		emc-timings-1 {
+			/* Hynix 1GB 667MHZ */
+			nvidia,ram-code = <1>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x74830303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x73430303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0xc0000030
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0503 0x72830504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000025
+					0x00000001 0x00000001 0x00000005 0x00000002
+					0x00000003 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0505 0x72440a06 0x001f0000 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emem-configuration = < 0x00000005 0xc000003d
+					0x00000001 0x00000002 0x00000008 0x00000004
+					0x00000004 0x00000001 0x00000002 0x00000007
+					0x00000002 0x00000002 0x00000003 0x00000006
+					0x06030202 0x000b0608 0x70850f09 0x001f0000 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emem-configuration = < 0x0000000a 0xc0000079
+					0x00000003 0x00000004 0x00000010 0x0000000b
+					0x0000000a 0x00000001 0x00000003 0x0000000b
+					0x00000002 0x00000002 0x00000004 0x00000008
+					0x08040202 0x00130b10 0x70ea1f11 0x001f0000 >;
+			};
+		};
+	};
+
+	memory-controller@7000f400 {
+		emc-timings-0 {
+			/* Elpida 1GB 667MHZ */
+			nvidia,ram-code = <0>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000004 0x00000000 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x000000c0 0x00000000 0x00000030
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000005 0x00000005
+					0x00000004 0x00000001 0x00000000 0x00000004
+					0x00000005 0x000000c7 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000002
+					0x00000008 0x00000001 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000181 0x00000000 0x00000060
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000009 0x00000009
+					0x00000004 0x00000002 0x00000000 0x00000004
+					0x00000005 0x0000018e 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000005
+					0x00000010 0x00000003 0x00000001 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000001
+					0x00000001 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000303 0x00000000 0x000000c0
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000012 0x00000012
+					0x00000004 0x00000004 0x00000000 0x00000004
+					0x00000005 0x0000031c 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000a
+					0x00000020 0x00000007 0x00000002 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000002
+					0x00000002 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000006 0x00000004 0x0000000a
+					0x0000000b 0x00000607 0x00000000 0x00000181
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000023 0x00000023
+					0x00000004 0x00000007 0x00000000 0x00000004
+					0x00000005 0x00000638 0x00000007 0x00000004
+					0x00000000 0x00000000 0x00004288 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00020000
+					0x00000100 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000d22 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200040>;
+				nvidia,emc-mode-reset = <0x80000321>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+
+				nvidia,emc-configuration =  < 0x0000000f
+					0x00000034 0x0000000a 0x00000003 0x00000003
+					0x00000008 0x00000002 0x00000009 0x00000003
+					0x00000003 0x00000002 0x00000001 0x00000000
+					0x00000004 0x00000006 0x00000004 0x0000000a
+					0x0000000c 0x000009e9 0x00000000 0x0000027a
+					0x00000001 0x00000008 0x00000001 0x00000000
+					0x00000007 0x0000000e 0x00000039 0x00000200
+					0x00000004 0x0000000a 0x00000000 0x00000004
+					0x00000005 0x00000a2a 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00007088 0x002600a4
+					0x00008000 0x0003c000 0x0003c000 0x0003c000
+					0x0003c000 0x00014000 0x00014000 0x00014000
+					0x00014000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00050000 0x00050000 0x00050000
+					0x00050000 0x000002a0 0x0800013d 0x00000000
+					0x77fff884 0x01f1f508 0x05057404 0x54000007
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x018b000c 0xa0f10000 0x00000000
+					0x00000000 0x800014d4 0xe8000000 0xff00ff89 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200058>;
+				nvidia,emc-mode-reset = <0x80000b71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000001f
+					0x00000069 0x00000017 0x00000007 0x00000005
+					0x0000000c 0x00000003 0x00000011 0x00000007
+					0x00000007 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000b 0x00000009 0x0000000b
+					0x00000011 0x00001412 0x00000000 0x00000504
+					0x00000002 0x0000000e 0x00000001 0x00000000
+					0x0000000c 0x00000016 0x00000072 0x00000200
+					0x00000005 0x00000015 0x00000000 0x00000006
+					0x00000007 0x00001453 0x0000000c 0x00000004
+					0x00000000 0x00000000 0x00005088 0xf00b0191
+					0x00008000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00018000 0x00018000 0x00018000
+					0x00018000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000c 0x0000000c 0x0000000c
+					0x0000000c 0x000002a0 0x0800013d 0x22220000
+					0x77fff884 0x01f1f501 0x07077404 0x54000000
+					0x080001e8 0x0a000021 0x00000802 0x00020000
+					0x00000100 0x0156000c 0xa0f10000 0x00000000
+					0x00000000 0x800028a5 0xe8000000 0xff00ff49 >;
+			};
+		};
+
+		emc-timings-1 {
+			/* Hynix 1GB 667MHZ */
+			nvidia,ram-code = <1>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000004 0x00000000 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x000000c0 0x00000000 0x00000030
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000005 0x00000005
+					0x00000004 0x00000001 0x00000000 0x00000004
+					0x00000005 0x000000c7 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000002
+					0x00000008 0x00000001 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000181 0x00000000 0x00000060
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000009 0x00000009
+					0x00000004 0x00000002 0x00000000 0x00000004
+					0x00000005 0x0000018e 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000005
+					0x00000010 0x00000003 0x00000001 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000001
+					0x00000001 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000303 0x00000000 0x000000c0
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000012 0x00000012
+					0x00000004 0x00000004 0x00000000 0x00000004
+					0x00000005 0x0000031c 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000a
+					0x00000020 0x00000007 0x00000002 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000002
+					0x00000002 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000006 0x00000004 0x0000000a
+					0x0000000b 0x00000607 0x00000000 0x00000181
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000023 0x00000023
+					0x00000004 0x00000007 0x00000000 0x00000004
+					0x00000005 0x00000638 0x00000007 0x00000004
+					0x00000000 0x00000000 0x00004288 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00020000
+					0x00000100 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000d22 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200040>;
+				nvidia,emc-mode-reset = <0x80000321>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+
+				nvidia,emc-configuration =  < 0x0000000f
+					0x00000034 0x0000000a 0x00000003 0x00000003
+					0x00000008 0x00000002 0x00000009 0x00000003
+					0x00000003 0x00000002 0x00000001 0x00000000
+					0x00000004 0x00000006 0x00000004 0x0000000a
+					0x0000000c 0x000009e9 0x00000000 0x0000027a
+					0x00000001 0x00000008 0x00000001 0x00000000
+					0x00000007 0x0000000e 0x00000039 0x00000200
+					0x00000004 0x0000000a 0x00000000 0x00000004
+					0x00000005 0x00000a2a 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00007088 0x002600a4
+					0x00008000 0x0003c000 0x0003c000 0x0003c000
+					0x0003c000 0x00014000 0x00014000 0x00014000
+					0x00014000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00048000 0x00048000 0x00048000
+					0x00048000 0x000002a0 0x0800013d 0x00000000
+					0x77fff884 0x01f1f508 0x05057404 0x54000007
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x018b000c 0xa0f10000 0x00000000
+					0x00000000 0x800014d4 0xe8000000 0xff00ff89 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200058>;
+				nvidia,emc-mode-reset = <0x80000b71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000020
+					0x00000069 0x00000017 0x00000007 0x00000005
+					0x0000000c 0x00000003 0x00000011 0x00000007
+					0x00000007 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000b 0x00000009 0x0000000b
+					0x00000011 0x00001412 0x00000000 0x00000504
+					0x00000002 0x0000000e 0x00000001 0x00000000
+					0x0000000c 0x00000016 0x00000072 0x00000200
+					0x00000005 0x00000015 0x00000000 0x00000006
+					0x00000007 0x00001453 0x0000000c 0x00000004
+					0x00000000 0x00000000 0x00005088 0xf00b0191
+					0x00008000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000c 0x0000000c 0x0000000c
+					0x0000000c 0x000002a0 0x0600013d 0x22220000
+					0x77fff884 0x01f1f501 0x07077404 0x54000000
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x0156000c 0xa0f10000 0x00000000
+					0x00000000 0x800028a5 0xf8000000 0xff00ff49 >;
+			};
+		};
+	};
+
+	pad_battery: battery-pad {
+		compatible = "simple-battery";
+		device-chemistry = "lithium-ion-polymer";
+		charge-full-design-microamp-hours = <2940000>;
+		energy-full-design-microwatt-hours = <22000000>;
+		operating-range-celsius = <0 45>;
+	};
+
+	dock_battery: battery-dock {
+		compatible = "simple-battery";
+		device-chemistry = "lithium-ion-polymer";
+		charge-full-design-microamp-hours = <2260000>;
+		energy-full-design-microwatt-hours = <16000000>;
+		operating-range-celsius = <0 45>;
+	};
+
+	display-panel {
+		compatible = "innolux,g101ice-l01";
+	};
+
+	opp-table-emc {
+		/delete-node/ opp-750000000-1300;
+		/delete-node/ opp-800000000-1300;
+		/delete-node/ opp-900000000-1350;
+	};
+
+	opp-table-actmon {
+		/delete-node/ opp-750000000;
+		/delete-node/ opp-800000000;
+		/delete-node/ opp-900000000;
+	};
+
+	sound {
+		compatible = "asus,tegra-audio-rt5631-tf300tl",
+			     "nvidia,tegra-audio-rt5631";
+		nvidia,model = "Asus Transformer Pad TF300TL RT5631";
+
+		nvidia,audio-routing =
+			"Headphone Jack", "HPOL",
+			"Headphone Jack", "HPOR",
+			"Int Spk", "SPOL",
+			"Int Spk", "SPOR",
+			"MIC1", "MIC Bias1",
+			"MIC Bias1", "Mic Jack",
+			"DMIC", "Int Mic";
+
+		nvidia,audio-codec = <&rt5631>;
+	};
+};
diff --git a/arch/arm/boot/dts/nvidia/tegra30-asus-tf600t.dts b/arch/arm/boot/dts/nvidia/tegra30-asus-tf600t.dts
new file mode 100644
index 000000000000..5d9e23a43820
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-tf600t.dts
@@ -0,0 +1,2500 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/thermal/thermal.h>
+
+#include "tegra30.dtsi"
+#include "tegra30-cpu-opp.dtsi"
+#include "tegra30-cpu-opp-microvolt.dtsi"
+
+/ {
+	model = "Asus VivoTab RT TF600T";
+	compatible = "asus,tf600t", "nvidia,tegra30";
+	chassis-type = "convertible";
+
+	aliases {
+		mmc0 = &sdmmc4; /* eMMC */
+		mmc1 = &sdmmc1; /* uSD slot */
+		mmc2 = &sdmmc3; /* WiFi */
+
+		rtc0 = &pmic;
+		rtc1 = "/rtc@7000e000";
+
+		display1 = &hdmi;
+
+		serial1 = &uartc; /* Bluetooth */
+		serial2 = &uartb; /* GPS */
+	};
+
+	/*
+	 * The decompressor and also some bootloaders rely on a
+	 * pre-existing /chosen node to be available to insert the
+	 * command line and merge other ATAGS info.
+	 */
+	chosen {};
+
+	memory@80000000 {
+		reg = <0x80000000 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		linux,cma@80000000 {
+			compatible = "shared-dma-pool";
+			alloc-ranges = <0x80000000 0x30000000>;
+			size = <0x10000000>;		/* 256MiB */
+			linux,cma-default;
+			reusable;
+		};
+	};
+
+	host1x@50000000 {
+		hdmi: hdmi@54280000 {
+			status = "okay";
+
+			hdmi-supply = <&hdmi_5v0_sys>;
+			pll-supply = <&vdd_1v8_vio>;
+			vdd-supply = <&vdd_3v3_sys>;
+
+			nvidia,hpd-gpio = <&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>;
+			nvidia,ddc-i2c-bus = <&hdmi_ddc>;
+		};
+	};
+
+	vde@6001a000 {
+		assigned-clocks = <&tegra_car TEGRA30_CLK_VDE>;
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_P>;
+		assigned-clock-rates = <408000000>;
+	};
+
+	pinmux@70000868 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&state_default>;
+
+		state_default: pinmux {
+			/* SDMMC1 pinmux */
+			sdmmc1-clk {
+				nvidia,pins = "sdmmc1_clk_pz0";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			sdmmc1-cmd {
+				nvidia,pins = "sdmmc1_dat3_py4",
+					      "sdmmc1_dat2_py5",
+					      "sdmmc1_dat1_py6",
+					      "sdmmc1_dat0_py7",
+					      "sdmmc1_cmd_pz1";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			sdmmc1-cd {
+				nvidia,pins = "gmi_iordy_pi5";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			sdmmc1-wp {
+				nvidia,pins = "vi_d11_pt3";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* SDMMC2 pinmux */
+			vi-d1-pd5 {
+				nvidia,pins = "vi_d1_pd5",
+					      "vi_d2_pl0",
+					      "vi_d3_pl1",
+					      "vi_d5_pl3",
+					      "vi_d7_pl5";
+				nvidia,function = "sdmmc2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			vi-d8-pl6 {
+				nvidia,pins = "vi_d8_pl6",
+					      "vi_d9_pl7";
+				nvidia,function = "sdmmc2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+				nvidia,io-reset = <0>;
+			};
+
+			/* SDMMC3 pinmux */
+			sdmmc3-clk {
+				nvidia,pins = "sdmmc3_clk_pa6";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			sdmmc3-cmd {
+				nvidia,pins = "sdmmc3_cmd_pa7",
+					      "sdmmc3_dat0_pb7",
+					      "sdmmc3_dat1_pb6",
+					      "sdmmc3_dat2_pb5",
+					      "sdmmc3_dat3_pb4",
+					      "sdmmc3_dat4_pd1",
+					      "sdmmc3_dat5_pd0",
+					      "sdmmc3_dat6_pd3",
+					      "sdmmc3_dat7_pd4";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* SDMMC4 pinmux */
+			sdmmc4-clk {
+				nvidia,pins = "sdmmc4_clk_pcc4";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			sdmmc4-cmd {
+				nvidia,pins = "sdmmc4_cmd_pt7",
+					      "sdmmc4_dat0_paa0",
+					      "sdmmc4_dat1_paa1",
+					      "sdmmc4_dat2_paa2",
+					      "sdmmc4_dat3_paa3",
+					      "sdmmc4_dat4_paa4",
+					      "sdmmc4_dat5_paa5",
+					      "sdmmc4_dat6_paa6",
+					      "sdmmc4_dat7_paa7";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			sdmmc4-rst-n {
+				nvidia,pins = "sdmmc4_rst_n_pcc3";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			cam-mclk {
+				nvidia,pins = "cam_mclk_pcc0";
+				nvidia,function = "vi_alt3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* I2C pinmux */
+			gen1-i2c {
+				nvidia,pins = "gen1_i2c_scl_pc4",
+					      "gen1_i2c_sda_pc5";
+				nvidia,function = "i2c1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <TEGRA_PIN_DISABLE>;
+			};
+			gen2-i2c {
+				nvidia,pins = "gen2_i2c_scl_pt5",
+					      "gen2_i2c_sda_pt6";
+				nvidia,function = "i2c2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <TEGRA_PIN_DISABLE>;
+			};
+			cam-i2c {
+				nvidia,pins = "cam_i2c_scl_pbb1",
+					      "cam_i2c_sda_pbb2";
+				nvidia,function = "i2c3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <TEGRA_PIN_DISABLE>;
+			};
+			ddc-i2c {
+				nvidia,pins = "ddc_scl_pv4",
+					      "ddc_sda_pv5";
+				nvidia,function = "i2c4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <TEGRA_PIN_DISABLE>;
+			};
+			pwr-i2c {
+				nvidia,pins = "pwr_i2c_scl_pz6",
+					      "pwr_i2c_sda_pz7";
+				nvidia,function = "i2cpwr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <TEGRA_PIN_DISABLE>;
+			};
+			hotplug-i2c {
+				nvidia,pins = "pu4";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* HDMI pinmux */
+			hdmi-cec {
+				nvidia,pins = "hdmi_cec_pee3";
+				nvidia,function = "cec";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <TEGRA_PIN_DISABLE>;
+			};
+			hdmi-hpd {
+				nvidia,pins = "hdmi_int_pn7";
+				nvidia,function = "hdmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* UART-A */
+			ulpi-data0-po1 {
+				nvidia,pins = "ulpi_data0_po1";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			ulpi-data1-po2 {
+				nvidia,pins = "ulpi_data1_po2";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			ulpi-data5-po6 {
+				nvidia,pins = "ulpi_data5_po6";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			ulpi-data7-po0 {
+				nvidia,pins = "ulpi_data7_po0",
+					      "ulpi_data2_po3",
+					      "ulpi_data3_po4",
+					      "ulpi_data4_po5",
+					      "ulpi_data6_po7";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* UART-B */
+			uartb-txd-rts {
+				nvidia,pins = "uart2_txd_pc2",
+					      "uart2_rts_n_pj6";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			uartb-rxd-cts {
+				nvidia,pins = "uart2_rxd_pc3",
+					      "uart2_cts_n_pj5";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* UART-C */
+			uartc-rxd-cts {
+				nvidia,pins = "uart3_cts_n_pa1",
+					      "uart3_rxd_pw7";
+				nvidia,function = "uartc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			uartc-txd-rts {
+				nvidia,pins = "uart3_rts_n_pc0",
+					      "uart3_txd_pw6";
+				nvidia,function = "uartc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* UART-D */
+			ulpi-nxt-py2 {
+				nvidia,pins = "ulpi_nxt_py2";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			ulpi-clk-py0 {
+				nvidia,pins = "ulpi_clk_py0",
+					      "ulpi_dir_py1",
+					      "ulpi_stp_py3";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* I2S pinmux */
+			dap-i2s0 {
+				nvidia,pins = "dap1_fs_pn0",
+					      "dap1_din_pn1",
+					      "dap1_dout_pn2",
+					      "dap1_sclk_pn3";
+				nvidia,function = "i2s0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			dap-i2s1 {
+				nvidia,pins = "dap2_fs_pa2",
+					      "dap2_sclk_pa3",
+					      "dap2_din_pa4",
+					      "dap2_dout_pa5";
+				nvidia,function = "i2s1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			dap3-fs {
+				nvidia,pins = "dap3_fs_pp0";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			dap3-din {
+				nvidia,pins = "dap3_din_pp1";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			dap3-dout {
+				nvidia,pins = "dap3_dout_pp2",
+					      "dap3_sclk_pp3";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			dap-i2s3 {
+				nvidia,pins = "dap4_fs_pp4",
+					      "dap4_din_pp5",
+					      "dap4_dout_pp6",
+					      "dap4_sclk_pp7";
+				nvidia,function = "i2s3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			i2s4 {
+				nvidia,pins = "pbb7";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Sensors pinmux */
+			nct-irq {
+				nvidia,pins = "pcc2";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			hall {
+				nvidia,pins = "pbb6";
+				nvidia,function = "vgp6";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Asus EC pinmux */
+			ec-irqs {
+				nvidia,pins = "kb_row10_ps2",
+					      "kb_row15_ps7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			ec-reqs {
+				nvidia,pins = "kb_col1_pq1";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Memory type bootstrap */
+			mem-boostraps {
+				nvidia,pins = "gmi_ad4_pg4",
+					      "gmi_ad5_pg5";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* PCI-e pinmux */
+			pex-l2-rst-n {
+				nvidia,pins = "pex_l2_rst_n_pcc6",
+					      "pex_l0_rst_n_pdd1",
+					      "pex_l1_rst_n_pdd5";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			pex-l2-clkreq-n {
+				nvidia,pins = "pex_l2_clkreq_n_pcc7",
+					      "pex_l0_prsnt_n_pdd0",
+					      "pex_l0_clkreq_n_pdd2",
+					      "pex_wake_n_pdd3",
+					      "pex_l1_prsnt_n_pdd4",
+					      "pex_l1_clkreq_n_pdd6",
+					      "pex_l2_prsnt_n_pdd7";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Display A pinmux */
+			lcd-pwr0-pb2 {
+				nvidia,pins = "lcd_pwr0_pb2",
+					      "lcd_pclk_pb3",
+					      "lcd_pwr1_pc1",
+					      "lcd_d0_pe0",
+					      "lcd_d1_pe1",
+					      "lcd_d2_pe2",
+					      "lcd_d3_pe3",
+					      "lcd_d4_pe4",
+					      "lcd_d5_pe5",
+					      "lcd_d6_pe6",
+					      "lcd_d7_pe7",
+					      "lcd_d8_pf0",
+					      "lcd_d9_pf1",
+					      "lcd_d10_pf2",
+					      "lcd_d11_pf3",
+					      "lcd_d12_pf4",
+					      "lcd_d13_pf5",
+					      "lcd_d14_pf6",
+					      "lcd_d15_pf7",
+					      "lcd_de_pj1",
+					      "lcd_hsync_pj3",
+					      "lcd_vsync_pj4",
+					      "lcd_d16_pm0",
+					      "lcd_d17_pm1",
+					      "lcd_d18_pm2",
+					      "lcd_d19_pm3",
+					      "lcd_d20_pm4",
+					      "lcd_d21_pm5",
+					      "lcd_d22_pm6",
+					      "lcd_d23_pm7",
+					      "lcd_dc0_pn6",
+					      "lcd_sdin_pz2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			lcd-cs0-n-pn4 {
+				nvidia,pins = "lcd_sdout_pn5",
+					      "lcd_wr_n_pz3",
+					      "lcd_pwr2_pc6",
+					      "lcd_dc1_pd2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			blink {
+				nvidia,pins = "clk_32k_out_pa0";
+				nvidia,function = "blink";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* KBC keys */
+			kb-col0 {
+				nvidia,pins = "kb_col0_pq0",
+					      "kb_row1_pr1",
+					      "kb_row3_pr3",
+					      "kb_row7_pr7",
+					      "kb_row8_ps0";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			kb-col5 {
+				nvidia,pins = "kb_col5_pq5",
+					      "kb_col7_pq7",
+					      "kb_row2_pr2",
+					      "kb_row4_pr4",
+					      "kb_row5_pr5",
+					      "kb_row13_ps5";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi-cs0-n-pj0 {
+				nvidia,pins = "gmi_wp_n_pc7",
+					      "gmi_wait_pi7",
+					      "gmi_cs0_n_pj0",
+					      "gmi_cs1_n_pj2",
+					      "gmi_cs2_n_pk3",
+					      "gmi_cs3_n_pk4";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			vi-pclk-pt0 {
+				nvidia,pins = "vi_pclk_pt0";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+				nvidia,io-reset = <0>;
+			};
+
+			/* GPIO keys pinmux */
+			power-key {
+				nvidia,pins = "pv0";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			vol-keys {
+				nvidia,pins = "kb_col3_pq3",
+					      "kb_col4_pq4";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Bluetooth */
+			bt-shutdown {
+				nvidia,pins = "pu0";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			bt-dev-wake {
+				nvidia,pins = "pu1";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			bt-host-wake {
+				nvidia,pins = "pu6";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pu2 {
+				nvidia,pins = "pu2";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			pu3 {
+				nvidia,pins = "pu3";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			pcc1 {
+				nvidia,pins = "pcc1";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			pv2 {
+				nvidia,pins = "pv2";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			pv3 {
+				nvidia,pins = "pv3";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi-vsync-pd6 {
+				nvidia,pins = "vi_vsync_pd6",
+					      "vi_hsync_pd7";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+				nvidia,io-reset = <0>;
+			};
+			vi-d10-pt2 {
+				nvidia,pins = "vi_d10_pt2",
+					      "vi_d0_pt4",
+					      "pbb0";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			kb-row0-pr0 {
+				nvidia,pins = "kb_row0_pr0";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			gmi-ad0-pg0 {
+				nvidia,pins = "gmi_ad0_pg0",
+					      "gmi_ad1_pg1",
+					      "gmi_ad2_pg2",
+					      "gmi_ad3_pg3",
+					      "gmi_ad6_pg6",
+					      "gmi_ad7_pg7",
+					      "gmi_wr_n_pi0",
+					      "gmi_oe_n_pi1",
+					      "gmi_dqs_pi2",
+					      "gmi_adv_n_pk0",
+					      "gmi_clk_pk1";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			gmi-ad13-ph5 {
+				nvidia,pins = "gmi_ad13_ph5";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			gmi-ad10-ph2 {
+				nvidia,pins = "gmi_ad10_ph2",
+					      "gmi_ad11_ph3",
+					      "gmi_ad14_ph6";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			gmi-ad12-ph4 {
+				nvidia,pins = "gmi_ad12_ph4",
+					      "gmi_rst_n_pi4",
+					      "gmi_cs7_n_pi6";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Vibrator control */
+			vibrator {
+				nvidia,pins = "gmi_ad11_ph3";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* PWM pinmux */
+			pwm-0 {
+				nvidia,pins = "gmi_ad8_ph0";
+				nvidia,function = "pwm0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			pwm-2 {
+				nvidia,pins = "pu5";
+				nvidia,function = "pwm2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi-cs-n {
+				nvidia,pins = "gmi_cs4_n_pk2",
+					      "gmi_cs6_n_pi3";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Spdif pinmux */
+			spdif-out {
+				nvidia,pins = "spdif_out_pk5";
+				nvidia,function = "spdif";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			spdif-in {
+				nvidia,pins = "spdif_in_pk6";
+				nvidia,function = "spdif";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			vi-d4-pl2 {
+				nvidia,pins = "vi_d4_pl2";
+				nvidia,function = "vi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			vi-d6-pl4 {
+				nvidia,pins = "vi_d6_pl4";
+				nvidia,function = "vi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+				nvidia,lock = <0>;
+				nvidia,io-reset = <0>;
+			};
+			vi-mclk-pt1 {
+				nvidia,pins = "vi_mclk_pt1";
+				nvidia,function = "vi";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			jtag {
+				nvidia,pins = "jtag_rtck_pu7";
+				nvidia,function = "rtck";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			crt-sync {
+				nvidia,pins = "crt_hsync_pv6",
+					      "crt_vsync_pv7";
+				nvidia,function = "crt";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			clk1-out {
+				nvidia,pins = "clk1_out_pw4";
+				nvidia,function = "extperiph1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			clk2-out {
+				nvidia,pins = "clk2_out_pw5";
+				nvidia,function = "extperiph2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			clk3-out {
+				nvidia,pins = "clk3_out_pee0";
+				nvidia,function = "extperiph3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			sys-clk-req {
+				nvidia,pins = "sys_clk_req_pz5";
+				nvidia,function = "sysclk";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pbb3 {
+				nvidia,pins = "pbb3";
+				nvidia,function = "vgp3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			pbb4 {
+				nvidia,pins = "pbb4";
+				nvidia,function = "vgp4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			pbb5 {
+				nvidia,pins = "pbb5";
+				nvidia,function = "vgp5";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			clk2-req-pcc5 {
+				nvidia,pins = "clk2_req_pcc5",
+					      "clk1_req_pee2";
+				nvidia,function = "dap";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			clk3-req-pee1 {
+				nvidia,pins = "clk3_req_pee1";
+				nvidia,function = "dev3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			owr {
+				nvidia,pins = "owr";
+				nvidia,function = "owr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* GPIO power/drive control */
+			drive-dap1 {
+				nvidia,pins = "drive_dap1",
+					      "drive_dap2",
+					      "drive_dbg",
+					      "drive_at5",
+					      "drive_gme",
+					      "drive_ddc",
+					      "drive_ao1",
+					      "drive_uart3";
+				nvidia,high-speed-mode = <TEGRA_PIN_DISABLE>;
+				nvidia,schmitt = <TEGRA_PIN_ENABLE>;
+				nvidia,low-power-mode = <TEGRA_PIN_LP_DRIVE_DIV_1>;
+				nvidia,pull-down-strength = <31>;
+				nvidia,pull-up-strength = <31>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+			};
+			drive-sdio1 {
+				nvidia,pins = "drive_sdio1",
+					      "drive_sdio3";
+				nvidia,high-speed-mode = <TEGRA_PIN_DISABLE>;
+				nvidia,schmitt = <TEGRA_PIN_DISABLE>;
+				nvidia,pull-down-strength = <46>;
+				nvidia,pull-up-strength = <42>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FAST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FAST>;
+			};
+			drive-sdmmc4 {
+				nvidia,pins = "drive_gma",
+					      "drive_gmb",
+					      "drive_gmc",
+					      "drive_gmd";
+				nvidia,pull-down-strength = <9>;
+				nvidia,pull-up-strength = <9>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+			};
+		};
+	};
+
+	uartb: serial@70006040 {
+		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
+		status = "okay";
+
+		/* Broadcom GPS BCM47511 */
+	};
+
+	uartc: serial@70006200 {
+		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
+		status = "okay";
+
+		nvidia,adjust-baud-rates = <0 9600 100>,
+					   <9600 115200 200>,
+					   <1000000 4000000 136>;
+
+		/* Azurewave AW-NH665 BCM4330B1 */
+		bluetooth {
+			compatible = "brcm,bcm4330-bt";
+			max-speed = <4000000>;
+
+			clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
+			clock-names = "txco";
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(U, 6) IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "host-wakeup";
+
+			device-wakeup-gpios = <&gpio TEGRA_GPIO(U, 1) GPIO_ACTIVE_HIGH>;
+			shutdown-gpios = <&gpio TEGRA_GPIO(U, 0) GPIO_ACTIVE_HIGH>;
+
+			vbat-supply = <&vdd_3v3_com>;
+			vddio-supply = <&vdd_1v8_vio>;
+		};
+	};
+
+	pwm@7000a000 {
+		status = "okay";
+	};
+
+	gen1_i2c: i2c@7000c000 {
+		status = "okay";
+		clock-frequency = <100000>;
+
+		/* Nuvoton NPCE698LA0BX embedded controller */
+	};
+
+	i2c@7000c400 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		/* Atmel Maxtouch MXT1664 HID over I2C */
+		touchscreen@4b {
+			compatible = "hid-over-i2c";
+			reg = <0x4b>;
+
+			hid-descr-addr = <0x0000>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(H, 4) IRQ_TYPE_LEVEL_LOW>;
+
+			vdd-supply = <&vdd_3v3_sys>;
+			vddl-supply = <&vdd_1v8_vio>;
+		};
+	};
+
+	i2c@7000c500 {
+		status = "okay";
+		clock-frequency = <100000>;
+
+		/* TI TPS61050/61052 Boost Converter */
+		flash-led@33 {
+			compatible = "ti,tps61052";
+			reg = <0x33>;
+
+			led {
+				color = <LED_COLOR_ID_WHITE>;
+			};
+		};
+
+		imu@69 {
+			compatible = "invensense,mpu6050";
+			reg = <0x69>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(X, 1) IRQ_TYPE_EDGE_RISING>;
+
+			vdd-supply   = <&vdd_3v3_sys>;
+			vddio-supply = <&vdd_1v8_vio>;
+
+			mount-matrix =	 "0", "-1",  "0",
+					"-1",  "0",  "0",
+					 "0",  "0", "-1";
+
+			/* External I2C interface */
+			i2c-gate {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				magnetometer@d {
+					compatible = "asahi-kasei,ak8975";
+					reg = <0x0d>;
+
+					interrupt-parent = <&gpio>;
+					interrupts = <TEGRA_GPIO(D, 5) IRQ_TYPE_EDGE_RISING>;
+
+					vdd-supply = <&vdd_3v3_sys>;
+					vid-supply = <&vdd_1v8_vio>;
+
+					mount-matrix =	 "0", "-1",  "0",
+							"-1",  "0",  "0",
+							 "0",  "0", "-1";
+				};
+			};
+		};
+	};
+
+	hdmi_ddc: i2c@7000c700 {
+		status = "okay";
+		clock-frequency = <93750>;
+	};
+
+	i2c@7000d000 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		rt5640: audio-codec@1c {
+			compatible = "realtek,rt5640";
+			reg = <0x1c>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+			clock-names = "mclk";
+		};
+
+		/* Texas Instruments TPS659110 PMIC */
+		pmic: pmic@2d {
+			compatible = "ti,tps65911";
+			reg = <0x2d>;
+
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+
+			ti,en-gpio-sleep = <0 0 1 0 0 0 0 0 0>;
+			ti,system-power-controller;
+			ti,sleep-keep-ck32k;
+			ti,sleep-enable;
+
+			#gpio-cells = <2>;
+			gpio-controller;
+
+			vcc1-supply = <&vdd_5v0_bat>;
+			vcc2-supply = <&vdd_5v0_bat>;
+			vcc3-supply = <&vdd_1v8_vio>;
+			vcc4-supply = <&vdd_5v0_sys>;
+			vcc5-supply = <&vdd_5v0_bat>;
+			vcc6-supply = <&vdd_3v3_sys>;
+			vcc7-supply = <&vdd_5v0_bat>;
+			vccio-supply = <&vdd_5v0_bat>;
+
+			pmic-sleep-hog {
+				gpio-hog;
+				gpios = <2 GPIO_ACTIVE_HIGH>;
+				output-high;
+			};
+
+			regulators {
+				vdd_lcd: vdd1 {
+					regulator-name = "vddio_ddr_1v2";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+					ti,regulator-ext-sleep-control = <8>;
+				};
+
+				vddio_ddr: vdd2 {
+					regulator-name = "vddio_ddr";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				vdd_cpu: vddctrl {
+					regulator-name = "vdd_cpu,vdd_sys";
+					regulator-min-microvolt = <600000>;
+					regulator-max-microvolt = <1400000>;
+					regulator-coupled-with = <&vdd_core>;
+					regulator-coupled-max-spread = <300000>;
+					regulator-max-step-microvolt = <100000>;
+					regulator-always-on;
+					regulator-boot-on;
+					ti,regulator-ext-sleep-control = <1>;
+
+					nvidia,tegra-cpu-regulator;
+				};
+
+				vdd_1v8_vio: vio {
+					regulator-name = "vdd_1v8_gen";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				/* eMMC VDD */
+				vcore_emmc: ldo1 {
+					regulator-name = "vdd_emmc_core";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+				};
+
+				/* ldo2 and ldo3 are not used by TF600T */
+
+				ldo4 {
+					regulator-name = "vdd_rtc";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+				};
+
+				/* uSD slot VDDIO */
+				vddio_usd: ldo5 {
+					regulator-name = "vddio_sdmmc";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+				};
+
+				avdd_dsi_csi: ldo6 {
+					regulator-name = "avdd_dsi_csi";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+				};
+
+				ldo7 {
+					regulator-name = "vdd_pllm,x,u,a_p_c_s";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+					ti,regulator-ext-sleep-control = <8>;
+				};
+
+				ldo8 {
+					regulator-name = "vdd_ddr_hs";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+					ti,regulator-ext-sleep-control = <8>;
+				};
+			};
+		};
+
+		/* Capella CM3218 ambient light sensor */
+		light-sensor@48 {
+			compatible = "capella,cm32181";
+			reg = <0x48>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(L, 0) IRQ_TYPE_EDGE_RISING>;
+
+			vdd-supply = <&vdd_3v3_als>;
+		};
+
+		nct72: temperature-sensor@4c {
+			compatible = "onnn,nct1008";
+			reg = <0x4c>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(CC, 2) IRQ_TYPE_EDGE_FALLING>;
+
+			vcc-supply = <&vdd_3v3_sys>;
+			#thermal-sensor-cells = <1>;
+		};
+
+		vdd_core: core-regulator@60 {
+			compatible = "ti,tps62361";
+			reg = <0x60>;
+
+			regulator-name = "tps62361-vout";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1770000>;
+			regulator-coupled-with = <&vdd_cpu>;
+			regulator-coupled-max-spread = <300000>;
+			regulator-max-step-microvolt = <100000>;
+			regulator-boot-on;
+			regulator-always-on;
+			ti,enable-vout-discharge;
+			ti,vsel0-state-high;
+			ti,vsel1-state-high;
+
+			nvidia,tegra-core-regulator;
+		};
+	};
+
+	pmc@7000e400 {
+		status = "okay";
+		nvidia,invert-interrupt;
+		nvidia,suspend-mode = <2>;
+		nvidia,cpu-pwr-good-time = <2000>;
+		nvidia,cpu-pwr-off-time = <200>;
+		nvidia,core-pwr-good-time = <3845 3845>;
+		nvidia,core-pwr-off-time = <0>;
+		nvidia,core-power-req-active-high;
+		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
+
+		i2c-thermtrip {
+			nvidia,i2c-controller-id = <4>;
+			nvidia,bus-addr = <0x2d>;
+			nvidia,reg-addr = <0x3f>;
+			nvidia,reg-data = <0x81>;
+		};
+	};
+
+	spi@7000da00 {
+		status = "okay";
+		spi-max-frequency = <25000000>;
+
+		flash@1 {
+			compatible = "winbond,w25q32", "jedec,spi-nor";
+			reg = <1>;
+
+			spi-max-frequency = <20000000>;
+			vcc-supply = <&vdd_3v3_sys>;
+		};
+	};
+
+	memory-controller@7000f000 {
+		emc-timings-0 {
+			/* Elpida 2GB 750 MHZ */
+			nvidia,ram-code = <0>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0xc0000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x75e30303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0xc0000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x74e30303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0xc0000018
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0503 0x74430504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000025
+					0x00000001 0x00000001 0x00000005 0x00000002
+					0x00000003 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0505 0x74040a06 0x001f0000 >;
+			};
+
+			timing-375000000 {
+				clock-frequency = <375000000>;
+
+				nvidia,emem-configuration = < 0x00000005 0xc0000044
+					0x00000001 0x00000002 0x00000009 0x00000005
+					0x00000005 0x00000001 0x00000002 0x00000008
+					0x00000002 0x00000002 0x00000003 0x00000006
+					0x06030202 0x000d0709 0x7086110a 0x001f0000 >;
+			};
+
+			timing-750000000 {
+				clock-frequency = <750000000>;
+
+				nvidia,emem-configuration = < 0x0000000b 0xc0000087
+					0x00000004 0x00000005 0x00000012 0x0000000c
+					0x0000000b 0x00000002 0x00000003 0x0000000c
+					0x00000002 0x00000002 0x00000004 0x00000008
+					0x08040202 0x00160d12 0x710c2213 0x001f0000 >;
+			};
+		};
+
+		emc-timings-1 {
+			/* Hynix 2GB 750 MHZ */
+			nvidia,ram-code = <1>;
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010003 0xc0000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x74630303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000018
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0503 0x73c30504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000006 0xc0000025
+					0x00000001 0x00000001 0x00000005 0x00000002
+					0x00000003 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0505 0x73840a06 0x001f0000 >;
+			};
+
+			timing-375000000 {
+				clock-frequency = <375000000>;
+
+				nvidia,emem-configuration = < 0x0000000b 0xc0000044
+					0x00000001 0x00000002 0x00000009 0x00000005
+					0x00000005 0x00000001 0x00000002 0x00000008
+					0x00000002 0x00000002 0x00000003 0x00000006
+					0x06030202 0x000c0609 0x7086110a 0x001f0000 >;
+			};
+
+			timing-750000000 {
+				clock-frequency = <750000000>;
+
+				nvidia,emem-configuration = < 0x00000016 0xc0000087
+					0x00000003 0x00000004 0x00000012 0x0000000c
+					0x0000000b 0x00000002 0x00000003 0x0000000c
+					0x00000002 0x00000002 0x00000004 0x00000008
+					0x08040202 0x00150c12 0x710c2213 0x001f0000 >;
+			};
+		};
+
+		emc-timings-2 {
+			/* Micron 2GB 750 MHZ */
+			nvidia,ram-code = <2>;
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010003 0xc0000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x73430303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000018
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0503 0x74430504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000006 0xc0000025
+					0x00000001 0x00000001 0x00000005 0x00000002
+					0x00000003 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0505 0x74040a06 0x001f0000 >;
+			};
+
+			timing-375000000 {
+				clock-frequency = <375000000>;
+
+				nvidia,emem-configuration = < 0x0000000b 0xc0000044
+					0x00000001 0x00000002 0x00000009 0x00000005
+					0x00000005 0x00000001 0x00000002 0x00000008
+					0x00000002 0x00000002 0x00000003 0x00000006
+					0x06030202 0x000d0709 0x7086110a 0x001f0000 >;
+			};
+
+			timing-750000000 {
+				clock-frequency = <750000000>;
+
+				nvidia,emem-configuration = < 0x00000016 0xc0000087
+					0x00000004 0x00000005 0x00000012 0x0000000c
+					0x0000000b 0x00000003 0x00000003 0x0000000c
+					0x00000002 0x00000002 0x00000004 0x00000008
+					0x08040202 0x00160d12 0x710c2213 0x001f0000 >;
+			};
+		};
+	};
+
+	memory-controller@7000f400 {
+		emc-timings-0 {
+			/* Elpida 2GB 750 MHZ */
+			nvidia,ram-code = <0>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000007 0x00000000 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x000000c0 0x00000000 0x00000030
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000008 0x00000008
+					0x00000004 0x00000001 0x00000000 0x00000004
+					0x00000005 0x000000c7 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+
+				nvidia,emc-configuration =  < 0x00000002
+					0x0000000f 0x00000001 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000181 0x00000000 0x00000060
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000010 0x00000010
+					0x00000004 0x00000002 0x00000000 0x00000004
+					0x00000005 0x0000018e 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+
+				nvidia,emc-configuration =  < 0x00000004
+					0x0000001e 0x00000003 0x00000001 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000001
+					0x00000001 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000303 0x00000000 0x000000c0
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000020 0x00000020
+					0x00000004 0x00000004 0x00000000 0x00000004
+					0x00000005 0x0000031c 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+
+				nvidia,emc-configuration =  < 0x00000009
+					0x0000003d 0x00000007 0x00000002 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000002
+					0x00000002 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000006 0x00000004 0x0000000a
+					0x0000000b 0x00000607 0x00000000 0x00000181
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000040 0x00000040
+					0x00000004 0x00000007 0x00000000 0x00000004
+					0x00000005 0x00000638 0x00000007 0x00000004
+					0x00000000 0x00000000 0x00004288 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00020000
+					0x00000100 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000d22 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-375000000 {
+				clock-frequency = <375000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200040>;
+				nvidia,emc-mode-reset = <0x80000521>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+
+				nvidia,emc-configuration =  < 0x00000011
+					0x0000006f 0x0000000c 0x00000004 0x00000003
+					0x00000008 0x00000002 0x0000000a 0x00000004
+					0x00000004 0x00000002 0x00000001 0x00000000
+					0x00000004 0x00000006 0x00000004 0x0000000a
+					0x0000000c 0x00000b2d 0x00000000 0x000002cb
+					0x00000001 0x00000008 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000075 0x00000200
+					0x00000004 0x0000000c 0x00000000 0x00000004
+					0x00000005 0x00000b6d 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00007088 0x00200084
+					0x00008000 0x00034000 0x00034000 0x00034000
+					0x00034000 0x00014000 0x00014000 0x00014000
+					0x00014000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00048000 0x00048000 0x00048000
+					0x00048000 0x000002a0 0x0600013d 0x00000000
+					0x77fff884 0x01f1f508 0x05057404 0x54000007
+					0x080001e8 0x06000021 0x00000802 0x00020000
+					0x00000100 0x0150000c 0xa0f10000 0x00000000
+					0x00000000 0x8000174b 0xe8000000 0xff00ff89 >;
+			};
+
+			timing-750000000 {
+				clock-frequency = <750000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200058>;
+				nvidia,emc-mode-reset = <0x80000d71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000023
+					0x000000df 0x00000019 0x00000009 0x00000005
+					0x0000000d 0x00000004 0x00000013 0x00000009
+					0x00000009 0x00000003 0x00000001 0x00000000
+					0x00000007 0x0000000b 0x00000009 0x0000000b
+					0x00000011 0x0000169a 0x00000000 0x000005a6
+					0x00000003 0x00000010 0x00000001 0x00000000
+					0x0000000e 0x00000018 0x000000e9 0x00000200
+					0x00000005 0x00000017 0x00000000 0x00000007
+					0x00000008 0x000016da 0x0000000c 0x00000004
+					0x00000000 0x00000000 0x00005088 0xf0080191
+					0x00008000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00000008 0x00000008 0x00000008
+					0x00000008 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x000002a0 0x0600013d 0x22220000
+					0x77fff884 0x01f1f501 0x07077404 0x54000000
+					0x080001e8 0x06000021 0x00000802 0x00020000
+					0x00000100 0x00df000c 0xa0f10000 0x00000000
+					0x00000000 0x80002d93 0xf8000000 0xff00ff49 >;
+			};
+		};
+
+		emc-timings-1 {
+			/* Hynix 2GB 750 MHZ */
+			nvidia,ram-code = <1>;
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+
+				nvidia,emc-configuration =  < 0x00000002
+					0x0000000d 0x00000001 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000181 0x00000000 0x00000060
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x0000000e 0x0000000e
+					0x00000004 0x00000002 0x00000000 0x00000004
+					0x00000005 0x0000018e 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+
+				nvidia,emc-configuration =  < 0x00000004
+					0x0000001a 0x00000003 0x00000001 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000001
+					0x00000001 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000303 0x00000000 0x000000c0
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x0000001c 0x0000001c
+					0x00000004 0x00000004 0x00000000 0x00000004
+					0x00000005 0x0000031c 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+
+				nvidia,emc-configuration =  < 0x00000009
+					0x00000035 0x00000007 0x00000002 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000002
+					0x00000002 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000006 0x00000004 0x0000000a
+					0x0000000b 0x00000607 0x00000000 0x00000181
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000038 0x00000038
+					0x00000004 0x00000007 0x00000000 0x00000004
+					0x00000005 0x00000638 0x00000007 0x00000004
+					0x00000000 0x00000000 0x00004288 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00020000
+					0x00000100 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000d22 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-375000000 {
+				clock-frequency = <375000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200040>;
+				nvidia,emc-mode-reset = <0x80000521>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+
+				nvidia,emc-configuration =  < 0x00000011
+					0x00000060 0x0000000c 0x00000003 0x00000004
+					0x00000008 0x00000002 0x0000000a 0x00000003
+					0x00000003 0x00000002 0x00000001 0x00000000
+					0x00000004 0x00000006 0x00000004 0x0000000a
+					0x0000000c 0x00000b2d 0x00000000 0x000002cb
+					0x00000001 0x00000008 0x00000001 0x00000000
+					0x00000007 0x00000010 0x00000066 0x00000200
+					0x00000004 0x0000000c 0x00000000 0x00000004
+					0x00000005 0x00000b6d 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00007288 0x00200084
+					0x00008000 0x00044000 0x00044000 0x00044000
+					0x00044000 0x00014000 0x00014000 0x00014000
+					0x00014000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00048000 0x00048000 0x00048000
+					0x00048000 0x000002a0 0x0600013d 0x00000000
+					0x77fff884 0x01f1f508 0x05057404 0x54000007
+					0x08000168 0x06000021 0x00000802 0x00020000
+					0x00000100 0x015f000c 0xa0f10000 0x00000000
+					0x00000000 0x8000174b 0xe8000000 0xff00ff89 >;
+			};
+
+			timing-750000000 {
+				clock-frequency = <750000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200058>;
+				nvidia,emc-mode-reset = <0x80000d71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000023
+					0x000000c1 0x00000019 0x00000008 0x00000005
+					0x0000000d 0x00000004 0x00000013 0x00000008
+					0x00000008 0x00000003 0x00000001 0x00000000
+					0x00000007 0x0000000b 0x00000009 0x0000000b
+					0x00000011 0x0000169a 0x00000000 0x000005a6
+					0x00000003 0x00000010 0x00000001 0x00000000
+					0x0000000e 0x00000018 0x000000cb 0x00000200
+					0x00000005 0x00000017 0x00000000 0x00000007
+					0x00000008 0x000016da 0x0000000c 0x00000004
+					0x00000000 0x00000000 0x00005088 0xf0080191
+					0x00008000 0x00008008 0x00000008 0x00000008
+					0x00000008 0x00000008 0x00000008 0x00000008
+					0x00000008 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x000002a0 0x0800013d 0x22220000
+					0x77fff884 0x01f1f501 0x07077404 0x54000000
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x00fd000c 0xa0f10000 0x00000000
+					0x00000000 0x80002d93 0xe8000000 0xff00ff49 >;
+			};
+		};
+
+		emc-timings-2 {
+			/* Micron 2GB 750 MHZ */
+			nvidia,ram-code = <2>;
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+
+				nvidia,emc-configuration =  < 0x00000002
+					0x00000008 0x00000001 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000181 0x00000000 0x00000060
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000009 0x00000009
+					0x00000004 0x00000002 0x00000000 0x00000004
+					0x00000005 0x0000018e 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+
+				nvidia,emc-configuration =  < 0x00000004
+					0x0000001e 0x00000003 0x00000001 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000001
+					0x00000001 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000303 0x00000000 0x000000c0
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000020 0x00000020
+					0x00000004 0x00000004 0x00000000 0x00000004
+					0x00000005 0x0000031c 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+
+				nvidia,emc-configuration =  < 0x00000009
+					0x0000003d 0x00000007 0x00000002 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000002
+					0x00000002 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000006 0x00000004 0x0000000a
+					0x0000000b 0x00000607 0x00000000 0x00000181
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000040 0x00000040
+					0x00000004 0x00000007 0x00000000 0x00000004
+					0x00000005 0x00000638 0x00000007 0x00000004
+					0x00000000 0x00000000 0x00004288 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00020000
+					0x00000100 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000d22 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-375000000 {
+				clock-frequency = <375000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200040>;
+				nvidia,emc-mode-reset = <0x80000521>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+
+				nvidia,emc-configuration =  < 0x00000011
+					0x0000006f 0x0000000c 0x00000004 0x00000003
+					0x00000008 0x00000002 0x0000000a 0x00000004
+					0x00000004 0x00000002 0x00000001 0x00000000
+					0x00000004 0x00000006 0x00000004 0x0000000a
+					0x0000000c 0x00000b2d 0x00000000 0x000002cb
+					0x00000001 0x00000008 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000075 0x00000200
+					0x00000004 0x0000000c 0x00000000 0x00000004
+					0x00000005 0x00000b6d 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00007088 0x00200084
+					0x00008000 0x00044000 0x00044000 0x00044000
+					0x00044000 0x00014000 0x00014000 0x00014000
+					0x00014000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00048000 0x00048000 0x00048000
+					0x00048000 0x000002a0 0x0800013d 0x00000000
+					0x77fff884 0x01f1f508 0x05057404 0x54000007
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x0150000c 0xa0f10000 0x00000000
+					0x00000000 0x8000174b 0xe8000000 0xff00ff89 >;
+			};
+
+			timing-750000000 {
+				clock-frequency = <750000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200058>;
+				nvidia,emc-mode-reset = <0x80000d71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000023
+					0x000000df 0x00000019 0x00000009 0x00000005
+					0x0000000d 0x00000004 0x00000013 0x00000009
+					0x00000009 0x00000006 0x00000001 0x00000000
+					0x00000007 0x0000000b 0x00000009 0x0000000b
+					0x00000011 0x0000169a 0x00000000 0x000005a6
+					0x00000003 0x00000010 0x00000001 0x00000000
+					0x0000000e 0x00000018 0x000000e9 0x00000200
+					0x00000005 0x00000017 0x00000000 0x00000007
+					0x00000008 0x000016da 0x0000000c 0x00000004
+					0x00000000 0x00000000 0x00005088 0xf0080191
+					0x00008000 0x0000800a 0x0000000a 0x0000000a
+					0x0000000a 0x00000008 0x00000008 0x00000008
+					0x00000008 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x007fc00a 0x0000000a 0x0000000a
+					0x0000000a 0x000002a0 0x0800013d 0x22220000
+					0x77fff884 0x01f1f501 0x07077404 0x54000000
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x00df000c 0xa0f10000 0x00000000
+					0x00000000 0x80002d93 0xf8000000 0xff00ff49 >;
+			};
+		};
+	};
+
+	hda@70030000 {
+		status = "okay";
+	};
+
+	ahub@70080000 {
+		i2s@70080400 {		/* i2s1 */
+			status = "okay";
+		};
+
+		/* BT SCO */
+		i2s@70080600 {		/* i2s3 */
+			status = "okay";
+		};
+	};
+
+	sdmmc1: mmc@78000000 {
+		status = "okay";
+		bus-width = <4>;
+
+		cd-gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
+		power-gpios =  <&gpio TEGRA_GPIO(D, 7) GPIO_ACTIVE_HIGH>;
+
+		vmmc-supply = <&vdd_3v3_sys>;
+		vqmmc-supply = <&vddio_usd>;
+	};
+
+	sdmmc3: mmc@78000400 {
+		status = "okay";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		assigned-clocks = <&tegra_car TEGRA30_CLK_SDMMC3>;
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_C>;
+		assigned-clock-rates = <50000000>;
+
+		max-frequency = <50000000>;
+		keep-power-in-suspend;
+		bus-width = <4>;
+		non-removable;
+
+		mmc-pwrseq = <&brcm_wifi_pwrseq>;
+		vmmc-supply = <&vdd_3v3_com>;
+		vqmmc-supply = <&vdd_1v8_vio>;
+
+		/* Azurewave AW-NH665 BCM4330B1 */
+		wifi@1 {
+			compatible = "brcm,bcm4329-fmac";
+			reg = <1>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(O, 4) IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "host-wake";
+		};
+	};
+
+	sdmmc4: mmc@78000600 {
+		status = "okay";
+		bus-width = <8>;
+
+		non-removable;
+		mmc-ddr-1_8v;
+
+		vmmc-supply = <&vcore_emmc>;
+		vqmmc-supply = <&vdd_1v8_vio>;
+	};
+
+	/* USB via ASUS connector */
+	usb@7d000000 {
+		compatible = "nvidia,tegra30-udc";
+		status = "okay";
+		dr_mode = "peripheral";
+	};
+
+	usb-phy@7d000000 {
+		status = "okay";
+		dr_mode = "peripheral";
+		nvidia,hssync-start-delay = <0>;
+		nvidia,xcvr-lsfslew = <2>;
+		nvidia,xcvr-lsrslew = <2>;
+		vbus-supply = <&vdd_5v0_sys>;
+	};
+
+	/* Dock's USB port */
+	usb@7d008000 {
+		status = "okay";
+	};
+
+	usb-phy@7d008000 {
+		status = "okay";
+		vbus-supply = <&vdd_5v0_bat>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+
+		enable-gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
+		power-supply = <&vdd_5v0_bl>;
+		pwms = <&pwm 0 71428>;
+
+		brightness-levels = <1 255>;
+		num-interpolated-steps = <254>;
+		default-brightness-level = <15>;
+	};
+
+	pad_battery: battery-pad {
+		compatible = "simple-battery";
+		device-chemistry = "lithium-ion-polymer";
+		charge-full-design-microamp-hours = <6760000>;
+		energy-full-design-microwatt-hours = <25000000>;
+		operating-range-celsius = <0 45>;
+	};
+
+	dock_battery: battery-dock {
+		compatible = "simple-battery";
+		device-chemistry = "lithium-ion-polymer";
+		charge-full-design-microamp-hours = <2980000>;
+		energy-full-design-microwatt-hours = <22000000>;
+		operating-range-celsius = <0 45>;
+	};
+
+	/* PMIC has a built-in 32KHz oscillator which is used by PMC */
+	clk32k_in: clock-32k {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "pmic-oscillator";
+	};
+
+	cpus {
+		cpu0: cpu@0 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+		cpu1: cpu@1 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+		cpu2: cpu@2 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+		cpu3: cpu@3 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+	};
+
+	extcon-keys {
+		compatible = "gpio-keys";
+
+		switch-dock-hall-sensor {
+			label = "Lid sensor";
+			gpios = <&gpio TEGRA_GPIO(BB, 6) GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			debounce-interval = <500>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		switch-lineout-detect {
+			label = "Audio dock line-out detect";
+			gpios = <&gpio TEGRA_GPIO(X, 3) GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LINEOUT_INSERT>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-power {
+			label = "Power";
+			gpios = <&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio TEGRA_GPIO(Q, 4) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio TEGRA_GPIO(Q, 3) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+	};
+
+	haptic-feedback {
+		compatible = "gpio-vibrator";
+		enable-gpios = <&gpio TEGRA_GPIO(H, 3) GPIO_ACTIVE_HIGH>;
+		vcc-supply = <&vdd_3v3_sys>;
+	};
+
+	opp-table-actmon {
+		/delete-node/ opp-800000000;
+		/delete-node/ opp-900000000;
+	};
+
+	opp-table-emc {
+		/delete-node/ opp-800000000-1300;
+		/delete-node/ opp-900000000-1350;
+	};
+
+	brcm_wifi_pwrseq: pwrseq-wifi {
+		compatible = "mmc-pwrseq-simple";
+
+		clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
+		clock-names = "ext_clock";
+
+		reset-gpios = <&gpio TEGRA_GPIO(P, 1) GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <300>;
+		power-off-delay-us = <300>;
+	};
+
+	vdd_5v0_bat: regulator-bat {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_ac_bat";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_5v0_cp: regulator-sby {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0_sby";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&pmic 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_bat>;
+	};
+
+	vdd_5v0_sys: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&pmic 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_bat>;
+	};
+
+	vdd_1v5_ddr: regulator-ddr {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_ddr";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&pmic 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_bat>;
+	};
+
+	vdd_3v3_sys: regulator-3v {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3_sys";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&pmic 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_bat>;
+	};
+
+	vdd_3v3_com: regulator-com {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3_com";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		gpio = <&gpio TEGRA_GPIO(D, 0) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_sys>;
+	};
+
+	vdd_3v3_als: regulator-als {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3_als";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		gpio = <&gpio TEGRA_GPIO(L, 5) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_sys>;
+	};
+
+	vdd_5v0_bl: regulator-bl {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0_bl";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		gpio = <&gpio TEGRA_GPIO(H, 0) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_bat>;
+	};
+
+	hdmi_5v0_sys: regulator-hdmi {
+		compatible = "regulator-fixed";
+		regulator-name = "hdmi_5v0_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_sys>;
+	};
+
+	sound {
+		compatible = "asus,tegra-audio-rt5640-tf600t",
+			     "nvidia,tegra-audio-rt5640";
+		nvidia,model = "Asus VivoTab RT TF600T RT5640";
+
+		nvidia,audio-routing =
+			"Headphones", "HPOR",
+			"Headphones", "HPOL",
+			"Speakers", "SPORP",
+			"Speakers", "SPORN",
+			"Speakers", "SPOLP",
+			"Speakers", "SPOLN",
+			"DMIC1", "Mic Jack";
+
+		nvidia,i2s-controller = <&tegra_i2s1>;
+		nvidia,audio-codec = <&rt5640>;
+
+		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_LOW>;
+		nvidia,mic-det-gpios = <&gpio TEGRA_GPIO(X, 2) GPIO_ACTIVE_LOW>;
+		nvidia,coupled-mic-hp-det;
+
+		clocks = <&tegra_car TEGRA30_CLK_PLL_A>,
+			 <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
+			 <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+		clock-names = "pll_a", "pll_a_out0", "mclk";
+
+		assigned-clocks = <&tegra_car TEGRA30_CLK_EXTERN1>,
+				  <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
+					 <&tegra_car TEGRA30_CLK_EXTERN1>;
+	};
+
+	thermal-zones {
+		/*
+		 * NCT72 has two sensors:
+		 *
+		 *	0: internal that monitors ambient/skin temperature
+		 *	1: external that is connected to the CPU's diode
+		 *
+		 * Ideally we should use userspace thermal governor,
+		 * but it's a much more complex solution.  The "skin"
+		 * zone exists as a simpler solution which prevents
+		 * Transformers from getting too hot from a user's
+		 * tactile perspective. The CPU zone is intended to
+		 * protect silicon from damage.
+		 */
+
+		skin-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct72 0>;
+
+			trips {
+				trip0: skin-alert {
+					/* throttle at 57C until temperature drops to 56.8C */
+					temperature = <57000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip1: skin-crit {
+					/* shut down at 65C */
+					temperature = <65000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&trip0>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&actmon THERMAL_NO_LIMIT
+								  THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		cpu-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct72 1>;
+
+			trips {
+				trip2: cpu-alert {
+					/* throttle at 75C until temperature drops to 74.8C */
+					temperature = <75000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip3: cpu-crit {
+					/* shut down at 90C */
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map1 {
+					trip = <&trip2>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&actmon THERMAL_NO_LIMIT
+								  THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/tegra30-asus-tf700t.dts b/arch/arm/boot/dts/nvidia/tegra30-asus-tf700t.dts
index 1a331dec3cfe..9c480fde2e76 100644
--- a/arch/arm/boot/dts/tegra30-asus-tf700t.dts
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-tf700t.dts
@@ -15,7 +15,7 @@
 			rgb {
 				status = "okay";
 
-				port@0 {
+				port {
 					dpi_output: endpoint {
 						remote-endpoint = <&bridge_input>;
 						bus-width = <24>;
@@ -758,6 +758,24 @@
 				vddio-supply = <&vdd_1v8_vio>;
 				vddmipi-supply = <&vdd_1v2_mipi>;
 
+				/*
+				 * Panasonic VVX10F004B00 or HYDIS HV101WU1-1E1
+				 * LCD SuperIPS+ Full HD panel.
+				 */
+				panel@1 {
+					compatible = "panasonic,vvx10f004b00";
+					reg = <1>;
+
+					power-supply = <&vdd_pnl>;
+					backlight = <&backlight>;
+
+					port {
+						panel_input: endpoint {
+							remote-endpoint = <&bridge_output>;
+						};
+					};
+				};
+
 				ports {
 					#address-cells = <1>;
 					#size-cells = <0>;
@@ -779,28 +797,18 @@
 						};
 					};
 				};
-
-				/*
-				 * Panasonic VVX10F004B00 or HYDIS HV101WU1-1E1
-				 * LCD SuperIPS+ Full HD panel.
-				 */
-				panel@1 {
-					compatible = "panasonic,vvx10f004b00";
-					reg = <1>;
-
-					power-supply = <&vdd_pnl>;
-					backlight = <&backlight>;
-
-					port {
-						panel_input: endpoint {
-							remote-endpoint = <&bridge_output>;
-						};
-					};
-				};
 			};
 		};
 	};
 
+	opp-table-actmon {
+		/delete-node/ opp-900000000;
+	};
+
+	opp-table-emc {
+		/delete-node/ opp-900000000-1350;
+	};
+
 	vdd_1v2_mipi: regulator-mipi {
 		compatible = "regulator-fixed";
 		regulator-name = "tc358768_1v2_vdd";
@@ -812,12 +820,21 @@
 		enable-active-high;
 		vin-supply = <&vdd_3v3_sys>;
 	};
-};
 
-&emc_icc_dvfs_opp_table {
-	/delete-node/ opp-900000000-1350;
-};
-
-&emc_bw_dfs_opp_table {
-	/delete-node/ opp-900000000;
+	sound {
+		compatible = "asus,tegra-audio-rt5631-tf700t",
+			     "nvidia,tegra-audio-rt5631";
+		nvidia,model = "Asus Transformer Infinity TF700T RT5631";
+
+		nvidia,audio-routing =
+			"Headphone Jack", "HPOL",
+			"Headphone Jack", "HPOR",
+			"Int Spk", "SPOL",
+			"Int Spk", "SPOR",
+			"MIC1", "MIC Bias1",
+			"MIC Bias1", "Mic Jack",
+			"DMIC", "Int Mic";
+
+		nvidia,audio-codec = <&rt5631>;
+	};
 };
diff --git a/arch/arm/boot/dts/tegra30-asus-transformer-common.dtsi b/arch/arm/boot/dts/nvidia/tegra30-asus-transformer-common.dtsi
index c662ab261ed5..ead95306840f 100644
--- a/arch/arm/boot/dts/tegra30-asus-transformer-common.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra30-asus-transformer-common.dtsi
@@ -33,6 +33,14 @@
 	 */
 	chosen {};
 
+	firmware {
+		trusted-foundations {
+			compatible = "tlm,trusted-foundations";
+			tlm,version-major = <2>;
+			tlm,version-minor = <8>;
+		};
+	};
+
 	memory@80000000 {
 		reg = <0x80000000 0x40000000>;
 	};
@@ -168,7 +176,7 @@
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
 				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
 				nvidia,lock = <0>;
-				nvidia,ioreset = <0>;
+				nvidia,io-reset = <0>;
 			};
 
 			/* SDMMC3 pinmux */
@@ -550,7 +558,7 @@
 				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
 			};
 
-			spi2_cs1_n_pw2 {
+			hp_detect {
 				nvidia,pins = "spi2_cs1_n_pw2";
 				nvidia,function = "spi2";
 				nvidia,pull = <TEGRA_PIN_PULL_UP>;
@@ -558,10 +566,10 @@
 				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
 			};
 
-			spi2_sck_px2 {
+			mic_detect {
 				nvidia,pins = "spi2_sck_px2";
 				nvidia,function = "spi2";
-				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
 				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
 			};
@@ -711,7 +719,7 @@
 				nvidia,tristate = <TEGRA_PIN_ENABLE>;
 				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
 				nvidia,lock = <0>;
-				nvidia,ioreset = <0>;
+				nvidia,io-reset = <0>;
 			};
 
 			/* GPIO keys pinmux */
@@ -805,7 +813,7 @@
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
 				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
 				nvidia,lock = <0>;
-				nvidia,ioreset = <0>;
+				nvidia,io-reset = <0>;
 			};
 
 			vi_d10_pt2 {
@@ -937,7 +945,7 @@
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
 				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
 				nvidia,lock = <0>;
-				nvidia,ioreset = <0>;
+				nvidia,io-reset = <0>;
 			};
 
 			vi_mclk_pt1 {
@@ -1080,6 +1088,7 @@
 
 	serial@70006040 {
 		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 		status = "okay";
 
@@ -1088,6 +1097,7 @@
 
 	serial@70006200 {
 		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 		status = "okay";
 
@@ -1187,17 +1197,6 @@
 		status = "okay";
 		clock-frequency = <400000>;
 
-		nct72: temperature-sensor@4c {
-			compatible = "onnn,nct1008";
-			reg = <0x4c>;
-
-			interrupt-parent = <&gpio>;
-			interrupts = <TEGRA_GPIO(CC, 2) IRQ_TYPE_EDGE_FALLING>;
-
-			vcc-supply = <&vdd_3v3_sys>;
-			#thermal-sensor-cells = <1>;
-		};
-
 		/* Texas Instruments TPS659110 PMIC */
 		pmic: pmic@2d {
 			compatible = "ti,tps65911";
@@ -1323,6 +1322,17 @@
 			};
 		};
 
+		nct72: temperature-sensor@4c {
+			compatible = "onnn,nct1008";
+			reg = <0x4c>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(CC, 2) IRQ_TYPE_EDGE_FALLING>;
+
+			vcc-supply = <&vdd_3v3_sys>;
+			#thermal-sensor-cells = <1>;
+		};
+
 		vdd_core: core-regulator@60 {
 			compatible = "ti,tps62361";
 			reg = <0x60>;
@@ -1509,9 +1519,8 @@
 
 	extcon-keys {
 		compatible = "gpio-keys";
-		interrupt-parent = <&gpio>;
 
-		dock-hall-sensor {
+		switch-dock-hall-sensor {
 			label = "Lid sensor";
 			gpios = <&gpio TEGRA_GPIO(S, 6) GPIO_ACTIVE_LOW>;
 			linux,input-type = <EV_SW>;
@@ -1521,7 +1530,7 @@
 			wakeup-source;
 		};
 
-		lineout-detect {
+		switch-lineout-detect {
 			label = "Audio dock line-out detect";
 			gpios = <&gpio TEGRA_GPIO(X, 3) GPIO_ACTIVE_LOW>;
 			linux,input-type = <EV_SW>;
@@ -1532,19 +1541,10 @@
 		};
 	};
 
-	firmware {
-		trusted-foundations {
-			compatible = "tlm,trusted-foundations";
-			tlm,version-major = <2>;
-			tlm,version-minor = <8>;
-		};
-	};
-
 	gpio-keys {
 		compatible = "gpio-keys";
-		interrupt-parent = <&gpio>;
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -1553,19 +1553,19 @@
 			wakeup-source;
 		};
 
-		volume-up {
-			label = "Volume Up";
-			gpios = <&gpio TEGRA_GPIO(Q, 2) GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEUP>;
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio TEGRA_GPIO(Q, 3) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
 			debounce-interval = <10>;
 			wakeup-event-action = <EV_ACT_ASSERTED>;
 			wakeup-source;
 		};
 
-		volume-down {
-			label = "Volume Down";
-			gpios = <&gpio TEGRA_GPIO(Q, 3) GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEDOWN>;
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio TEGRA_GPIO(Q, 2) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
 			debounce-interval = <10>;
 			wakeup-event-action = <EV_ACT_ASSERTED>;
 			wakeup-source;
@@ -1676,7 +1676,8 @@
 		nvidia,i2s-controller = <&tegra_i2s1>;
 
 		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_LOW>;
-		nvidia,hp-mute-gpios = <&gpio TEGRA_GPIO(X, 2) GPIO_ACTIVE_LOW>;
+		nvidia,mic-det-gpios = <&gpio TEGRA_GPIO(X, 2) GPIO_ACTIVE_LOW>;
+		nvidia,coupled-mic-hp-det;
 
 		clocks = <&tegra_car TEGRA30_CLK_PLL_A>,
 			 <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
diff --git a/arch/arm/boot/dts/tegra30-beaver.dts b/arch/arm/boot/dts/nvidia/tegra30-beaver.dts
index 5ad62b567d32..1d74179dde79 100644
--- a/arch/arm/boot/dts/tegra30-beaver.dts
+++ b/arch/arm/boot/dts/nvidia/tegra30-beaver.dts
@@ -1733,6 +1733,8 @@
 	};
 
 	serial@70006000 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -1974,6 +1976,28 @@
 		#clock-cells = <0>;
 	};
 
+	cpus {
+		cpu0: cpu@0 {
+			cpu-supply = <&vddctrl_reg>;
+			operating-points-v2 = <&cpu0_opp_table>;
+		};
+
+		cpu@1 {
+			cpu-supply = <&vddctrl_reg>;
+			operating-points-v2 = <&cpu0_opp_table>;
+		};
+
+		cpu@2 {
+			cpu-supply = <&vddctrl_reg>;
+			operating-points-v2 = <&cpu0_opp_table>;
+		};
+
+		cpu@3 {
+			cpu-supply = <&vddctrl_reg>;
+			operating-points-v2 = <&cpu0_opp_table>;
+		};
+	};
+
 	gpio-leds {
 		compatible = "gpio-leds";
 
@@ -2113,26 +2137,4 @@
 		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
 					 <&tegra_car TEGRA30_CLK_EXTERN1>;
 	};
-
-	cpus {
-		cpu0: cpu@0 {
-			cpu-supply = <&vddctrl_reg>;
-			operating-points-v2 = <&cpu0_opp_table>;
-		};
-
-		cpu@1 {
-			cpu-supply = <&vddctrl_reg>;
-			operating-points-v2 = <&cpu0_opp_table>;
-		};
-
-		cpu@2 {
-			cpu-supply = <&vddctrl_reg>;
-			operating-points-v2 = <&cpu0_opp_table>;
-		};
-
-		cpu@3 {
-			cpu-supply = <&vddctrl_reg>;
-			operating-points-v2 = <&cpu0_opp_table>;
-		};
-	};
 };
diff --git a/arch/arm/boot/dts/tegra30-cardhu-a02.dts b/arch/arm/boot/dts/nvidia/tegra30-cardhu-a02.dts
index 247185314f46..247185314f46 100644
--- a/arch/arm/boot/dts/tegra30-cardhu-a02.dts
+++ b/arch/arm/boot/dts/nvidia/tegra30-cardhu-a02.dts
diff --git a/arch/arm/boot/dts/tegra30-cardhu-a04.dts b/arch/arm/boot/dts/nvidia/tegra30-cardhu-a04.dts
index 2911f08863a0..2911f08863a0 100644
--- a/arch/arm/boot/dts/tegra30-cardhu-a04.dts
+++ b/arch/arm/boot/dts/nvidia/tegra30-cardhu-a04.dts
diff --git a/arch/arm/boot/dts/tegra30-cardhu.dtsi b/arch/arm/boot/dts/nvidia/tegra30-cardhu.dtsi
index ba257ed36d9c..0120859d6d72 100644
--- a/arch/arm/boot/dts/tegra30-cardhu.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra30-cardhu.dtsi
@@ -170,11 +170,14 @@
 	};
 
 	serial@70006000 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
 	serial@70006200 {
 		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 		status = "okay";
 	};
@@ -468,6 +471,33 @@
 		};
 	};
 
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-power {
+			label = "Power";
+			interrupt-parent = <&pmic>;
+			interrupts = <2 0>;
+			linux,code = <KEY_POWER>;
+			debounce-interval = <100>;
+			wakeup-source;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <10>;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio TEGRA_GPIO(R, 1) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <10>;
+		};
+	};
+
 	panel: panel {
 		compatible = "chunghwa,claa101wb01";
 		ddc-i2c-bus = <&panelddc>;
@@ -681,31 +711,4 @@
 			};
 		};
 	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		power {
-			label = "Power";
-			interrupt-parent = <&pmic>;
-			interrupts = <2 0>;
-			linux,code = <KEY_POWER>;
-			debounce-interval = <100>;
-			wakeup-source;
-		};
-
-		volume-down {
-			label = "Volume Down";
-			gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEDOWN>;
-			debounce-interval = <10>;
-		};
-
-		volume-up {
-			label = "Volume Up";
-			gpios = <&gpio TEGRA_GPIO(R, 1) GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEUP>;
-			debounce-interval = <10>;
-		};
-	};
 };
diff --git a/arch/arm/boot/dts/tegra30-colibri-eval-v3.dts b/arch/arm/boot/dts/nvidia/tegra30-colibri-eval-v3.dts
index 7d4a6ca4936a..1990bf8e122d 100644
--- a/arch/arm/boot/dts/tegra30-colibri-eval-v3.dts
+++ b/arch/arm/boot/dts/nvidia/tegra30-colibri-eval-v3.dts
@@ -38,6 +38,8 @@
 
 	/* Colibri UART-A */
 	serial@70006000 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -136,7 +138,7 @@
 		pwms = <&pwm 0 5000000>; /* PWM<A> */
 	};
 
-	clk16m: osc3 {
+	clk16m: clock-osc3 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <16000000>;
@@ -145,7 +147,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "SODIMM pin 45 wakeup";
 			gpios = <&gpio TEGRA_GPIO(V, 1) GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_WAKEUP>;
diff --git a/arch/arm/boot/dts/tegra30-colibri.dtsi b/arch/arm/boot/dts/nvidia/tegra30-colibri.dtsi
index 22231d450b1b..81c8a5fd92cc 100644
--- a/arch/arm/boot/dts/tegra30-colibri.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra30-colibri.dtsi
@@ -20,6 +20,15 @@
 		};
 	};
 
+	gpio: gpio@6000d000 {
+		lan-reset-n-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(DD, 0) GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "LAN_RESET#";
+		};
+	};
+
 	pinmux@70000868 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&state_default>;
@@ -239,7 +248,7 @@
 				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
 			};
 			spdif-in-pk6 {
-				nvidia,pins =	"spdif_in_pk6";
+				nvidia,pins = "spdif_in_pk6";
 				nvidia,function = "hda";
 				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
@@ -364,7 +373,7 @@
 			};
 			/* Multiplexed and therefore disabled */
 			cam-mclk-pcc0 {
-				nvidia,pins =	"cam_mclk_pcc0";
+				nvidia,pins = "cam_mclk_pcc0";
 				nvidia,function = "vi_alt3";
 				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
 				nvidia,tristate = <TEGRA_PIN_ENABLE>;
@@ -511,7 +520,7 @@
 
 			/* Colibri USBC_DET */
 			spdif-out-pk5 {
-				nvidia,pins =	"spdif_out_pk5";
+				nvidia,pins = "spdif_out_pk5";
 				nvidia,function = "rsvd2";
 				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
@@ -701,11 +710,13 @@
 
 	serial@70006040 {
 		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 	};
 
 	serial@70006300 {
 		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 	};
 
@@ -849,8 +860,7 @@
 		touchscreen@41 {
 			compatible = "st,stmpe811";
 			reg = <0x41>;
-			irq-gpio = <&gpio TEGRA_GPIO(V, 0) IRQ_TYPE_LEVEL_LOW>;
-			interrupt-controller;
+			irq-gpio = <&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_LOW>;
 			id = <0>;
 			blocks = <0x5>;
 			irq-trigger = <0x1>;
@@ -864,6 +874,11 @@
 			st,sample-time = <4>;
 			/* forbid to use ADC channels 3-0 (touch) */
 
+			stmpe_adc {
+				compatible = "st,stmpe-adc";
+				st,norequest-mask = <0x0F>;
+			};
+
 			stmpe_touchscreen {
 				compatible = "st,stmpe-ts";
 				/* 8 sample average control */
@@ -880,11 +895,6 @@
 				/* 5 ms touch detect interrupt delay */
 				st,touch-det-delay = <5>;
 			};
-
-			stmpe_adc {
-				compatible = "st,stmpe-adc";
-				st,norequest-mask = <0x0F>;
-			};
 		};
 
 		/*
@@ -972,7 +982,7 @@
 		vbus-supply = <&reg_lan_v_bus>;
 	};
 
-	clk32k_in: xtal1 {
+	clk32k_in: clock-xtal1 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <32768>;
@@ -1053,12 +1063,3 @@
 					 <&tegra_car TEGRA30_CLK_EXTERN1>;
 	};
 };
-
-&gpio {
-	lan-reset-n-hog {
-		gpio-hog;
-		gpios = <TEGRA_GPIO(DD, 0) GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "LAN_RESET#";
-	};
-};
diff --git a/arch/arm/boot/dts/tegra30-cpu-opp-microvolt.dtsi b/arch/arm/boot/dts/nvidia/tegra30-cpu-opp-microvolt.dtsi
index b8e0e9117021..b8e0e9117021 100644
--- a/arch/arm/boot/dts/tegra30-cpu-opp-microvolt.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra30-cpu-opp-microvolt.dtsi
diff --git a/arch/arm/boot/dts/tegra30-cpu-opp.dtsi b/arch/arm/boot/dts/nvidia/tegra30-cpu-opp.dtsi
index 5b9ebb75a09f..5b9ebb75a09f 100644
--- a/arch/arm/boot/dts/tegra30-cpu-opp.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra30-cpu-opp.dtsi
diff --git a/arch/arm/boot/dts/nvidia/tegra30-lg-p880.dts b/arch/arm/boot/dts/nvidia/tegra30-lg-p880.dts
new file mode 100644
index 000000000000..c6ef0a20c19f
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-lg-p880.dts
@@ -0,0 +1,489 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "tegra30-lg-x3.dtsi"
+
+/ {
+	model = "LG Optimus 4X HD P880";
+	compatible = "lg,p880", "nvidia,tegra30";
+
+	aliases {
+		mmc1 = &sdmmc3; /* uSD slot */
+		mmc2 = &sdmmc1; /* WiFi */
+	};
+
+	pinmux@70000868 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&state_default>;
+
+		state_default: pinmux {
+			/* WLAN SDIO pinmux */
+			host-wlan-wake {
+				nvidia,pins = "pu4";
+				nvidia,function = "pwm1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* GNSS UART-B pinmux */
+			uartb-rxd {
+				nvidia,pins = "uart2_rxd_pc3";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			uartb-txd {
+				nvidia,pins = "uart2_txd_pc2";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			gps-reset {
+				nvidia,pins = "kb_row7_pr7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* MicroSD pinmux */
+			sdmmc3-clk {
+				nvidia,pins = "sdmmc3_clk_pa6";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			sdmmc3-data {
+				nvidia,pins = "sdmmc3_cmd_pa7",
+						"sdmmc3_dat0_pb7",
+						"sdmmc3_dat1_pb6",
+						"sdmmc3_dat2_pb5",
+						"sdmmc3_dat3_pb4";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			microsd-detect {
+				nvidia,pins = "clk2_out_pw5";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* GPIO keys pinmux */
+			volume-up {
+				nvidia,pins = "ulpi_data6_po7";
+				nvidia,function = "spi2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Sensors pinmux */
+			current-alert-irq {
+				nvidia,pins = "uart2_rts_n_pj6";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* AUDIO pinmux */
+			sub-mic-ldo {
+				nvidia,pins = "gmi_cs7_n_pi6";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+		};
+	};
+
+	i2c@7000c400 {
+		touchscreen@20 {
+			rmi4-f11@11 {
+				syna,clip-x-high = <1440>;
+				syna,clip-y-high = <2560>;
+
+				touchscreen-inverted-y;
+			};
+		};
+	};
+
+	memory-controller@7000f000 {
+		emc-timings-0 {
+			/* SAMSUNG 1GB K4P8G304EB FGC1 533MHz */
+			nvidia,ram-code = <0>;
+
+			timing-12750000 {
+				clock-frequency = <12750000>;
+
+				nvidia,emem-configuration = < 0x00050001 0xc0000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x77230303 0x001f0000 >;
+			};
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0xc0000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x73e30303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0xc0000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x72c30303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0xc0000018
+					0x00000001 0x00000001 0x00000003 0x00000001
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060403 0x72430504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000025
+					0x00000001 0x00000001 0x00000006 0x00000003
+					0x00000005 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000003 0x00000002
+					0x02030001 0x00070506 0x71e40a07 0x001f0000 >;
+			};
+
+			timing-266500000 {
+				clock-frequency = <266500000>;
+
+				nvidia,emem-configuration = < 0x00000004 0xC0000030
+					0x00000001 0x00000002 0x00000008 0x00000004
+					0x00000006 0x00000001 0x00000002 0x00000005
+					0x00000001 0x00000000 0x00000003 0x00000003
+					0x03030001 0x00090608 0x70040c09 0x001f0000 >;
+			};
+
+			timing-533000000 {
+				clock-frequency = <533000000>;
+
+				nvidia,emem-configuration = < 0x00000008 0xC0000060
+					0x00000003 0x00000004 0x00000010 0x0000000a
+					0x0000000d 0x00000002 0x00000002 0x00000008
+					0x00000002 0x00000000 0x00000004 0x00000005
+					0x05040002 0x00110b10 0x70281811 0x001f0000 >;
+			};
+		};
+	};
+
+	memory-controller@7000f400 {
+		emc-timings-0 {
+			/* SAMSUNG 1GB K4P8G304EB FGC1 533MHz */
+			nvidia,ram-code = <0>;
+
+			timing-12750000 {
+				clock-frequency = <12750000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000000
+					0x00000001 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x00000009 0x0000002f 0x00000000 0x0000000b
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000002 0x00000002
+					0x00000003 0x00000008 0x00000004 0x00000001
+					0x00000002 0x00000036 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000009 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000164 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000003 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x00000009 0x00000060 0x00000000 0x00000018
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000004 0x00000004
+					0x00000003 0x00000008 0x00000004 0x00000001
+					0x00000002 0x0000006b 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x0000000a 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x800001c5 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000003
+					0x00000006 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x00000009 0x000000c0 0x00000000 0x00000030
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000008 0x00000008
+					0x00000003 0x00000008 0x00000004 0x00000001
+					0x00000002 0x000000d5 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000013 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x0000000a>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000006
+					0x0000000d 0x00000004 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x00000009 0x00000181 0x00000000 0x00000060
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x0000000f 0x0000000f
+					0x00000003 0x00000008 0x00000004 0x00000001
+					0x00000002 0x000001a9 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000025 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010042>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000013>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000c
+					0x0000001a 0x00000008 0x00000003 0x00000005
+					0x00000004 0x00000001 0x00000006 0x00000003
+					0x00000003 0x00000002 0x00000002 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000c
+					0x0000000a 0x00000303 0x00000000 0x000000c0
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000007 0x0000001d 0x0000001d
+					0x00000004 0x0000000b 0x00000005 0x00000001
+					0x00000002 0x00000351 0x00000004 0x00000006
+					0x00000000 0x00000000 0x00004282 0x004400a4
+					0x00008000 0x00070000 0x00070000 0x00070000
+					0x00070000 0x00070000 0x00070000 0x00070000
+					0x00070000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000e0220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x0000004a 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-266500000 {
+				clock-frequency = <266500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010042>;
+				nvidia,emc-mode-2 = <0x00020002>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000018>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000f
+					0x00000022 0x0000000b 0x00000004 0x00000005
+					0x00000005 0x00000001 0x00000007 0x00000004
+					0x00000004 0x00000002 0x00000002 0x00000000
+					0x00000002 0x00000005 0x00000002 0x0000000c
+					0x0000000b 0x000003ef 0x00000000 0x000000fb
+					0x00000001 0x00000001 0x00000004 0x00000000
+					0x00000001 0x00000009 0x00000026 0x00000026
+					0x00000004 0x0000000e 0x00000006 0x00000001
+					0x00000002 0x00000455 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00006282 0x003200a4
+					0x00008000 0x00050000 0x00050000 0x00050000
+					0x00050000 0x00050000 0x00050000 0x00050000
+					0x00050000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00060000 0x00060000 0x00060000
+					0x00060000 0x000b0220 0x0800003d 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000060 0x000a000a 0xa0f10000 0x00000000
+					0x00000000 0x800008ee 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-533000000 {
+				clock-frequency = <533000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x000100c2>;
+				nvidia,emc-mode-2 = <0x00020006>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000030>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000001f
+					0x00000045 0x00000016 0x00000009 0x00000008
+					0x00000009 0x00000003 0x0000000d 0x00000009
+					0x00000009 0x00000005 0x00000003 0x00000000
+					0x00000004 0x00000009 0x00000006 0x0000000d
+					0x00000010 0x000007df 0x00000000 0x000001f7
+					0x00000003 0x00000003 0x00000009 0x00000000
+					0x00000001 0x0000000f 0x0000004b 0x0000004b
+					0x00000008 0x0000001b 0x0000000c 0x00000001
+					0x00000002 0x000008aa 0x00000000 0x00000006
+					0x00000000 0x00000000 0x00006282 0xf0120091
+					0x00008000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00090220 0x0800003d 0x00000000
+					0x77ffc004 0x01f1f408 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x000000c0 0x000e000e 0xa0f10000 0x00000000
+					0x00000000 0x800010d9 0xe0000000 0xff00ff88 >;
+			};
+		};
+	};
+
+	sdmmc3: mmc@78000400 {
+		status = "okay";
+
+		cd-gpios = <&gpio TEGRA_GPIO(W, 5) GPIO_ACTIVE_LOW>;
+		bus-width = <4>;
+
+		vmmc-supply = <&vdd_usd>;
+		vqmmc-supply = <&vdd_1v8_vio>;
+	};
+
+	battery: battery-cell {
+		compatible = "simple-battery";
+		device-chemistry = "lithium-ion";
+		charge-full-design-microamp-hours = <2150000>;
+		energy-full-design-microwatt-hours = <8200000>;
+		operating-range-celsius = <0 45>;
+	};
+
+	gpio-keys {
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio TEGRA_GPIO(O, 7) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+	};
+
+	sound {
+		compatible = "lg,tegra-audio-max98089-p880",
+			     "nvidia,tegra-audio-max98089";
+		nvidia,model = "LG Optimus 4X HD MAX98089";
+
+		nvidia,int-mic-en-gpios = <&gpio TEGRA_GPIO(I, 6) GPIO_ACTIVE_HIGH>;
+	};
+};
diff --git a/arch/arm/boot/dts/nvidia/tegra30-lg-p895.dts b/arch/arm/boot/dts/nvidia/tegra30-lg-p895.dts
new file mode 100644
index 000000000000..e32fafc7f5e0
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-lg-p895.dts
@@ -0,0 +1,496 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "tegra30-lg-x3.dtsi"
+
+/ {
+	model = "LG Optimus Vu P895";
+	compatible = "lg,p895", "nvidia,tegra30";
+
+	pinmux@70000868 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&state_default>;
+
+		state_default: pinmux {
+			/* GNSS UART-B pinmux */
+			uartb-cts-rxd {
+				nvidia,pins = "uart2_cts_n_pj5",
+						"uart2_rxd_pc3";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			uartb-rts-txd {
+				nvidia,pins = "uart2_rts_n_pj6",
+						"uart2_txd_pc2";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			gps-reset {
+				nvidia,pins = "spdif_out_pk5";
+				nvidia,function = "spdif";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* GPIO keys pinmux */
+			memo-key {
+				nvidia,pins = "sdmmc3_dat1_pb6";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			volume-up {
+				nvidia,pins = "gmi_cs7_n_pi6";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Sensors pinmux */
+			current-alert-irq {
+				nvidia,pins = "spi1_cs0_n_px6";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Panel pinmux */
+			panel-vdd {
+				nvidia,pins = "pbb0";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* AUDIO pinmux */
+			sub-mic-ldo {
+				nvidia,pins = "gmi_dqs_pi2";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* Modem pinmux */
+			usim-detect {
+				nvidia,pins = "clk2_out_pw5";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* GPIO power/drive control */
+			drive-sdmmc4 {
+				nvidia,pins = "drive_gma",
+						"drive_gmb",
+						"drive_gmc",
+						"drive_gmd";
+				nvidia,pull-down-strength = <9>;
+				nvidia,pull-up-strength = <9>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+			};
+		};
+	};
+
+	i2c@7000c400 {
+		touchscreen@20 {
+			rmi4-f11@11 {
+				syna,clip-x-high = <1535>;
+				syna,clip-y-high = <2047>;
+			};
+		};
+	};
+
+	memory-controller@7000f000 {
+		emc-timings-2 {
+			/* Hynix 1GB H9TCNNN8JDMMPR LPDDR2 533MHz */
+			nvidia,ram-code = <2>;
+
+			timing-12750000 {
+				clock-frequency = <12750000>;
+
+				nvidia,emem-configuration = < 0x00020001 0xc0000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x77230303 0x001f0000 >;
+			};
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00030003 0xc0000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x73e30303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010003 0xc0000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x72c30303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000018
+					0x00000001 0x00000001 0x00000003 0x00000001
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060403 0x72430504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000006 0xc0000025
+					0x00000001 0x00000001 0x00000006 0x00000003
+					0x00000005 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000003 0x00000002
+					0x02030001 0x00070506 0x71e40a07 0x001f0000 >;
+			};
+
+			timing-266500000 {
+				clock-frequency = <266500000>;
+
+				nvidia,emem-configuration = < 0x00000008 0xc0000030
+					0x00000001 0x00000002 0x00000008 0x00000004
+					0x00000006 0x00000001 0x00000002 0x00000005
+					0x00000001 0x00000000 0x00000003 0x00000003
+					0x03030001 0x00090608 0x70040c09 0x001f0000 >;
+			};
+
+			timing-533000000 {
+				clock-frequency = <533000000>;
+
+				nvidia,emem-configuration = < 0x0000000f 0xc0000060
+					0x00000003 0x00000004 0x00000010 0x0000000a
+					0x0000000d 0x00000002 0x00000002 0x00000008
+					0x00000002 0x00000000 0x00000004 0x00000005
+					0x05040002 0x00110b10 0x70281811 0x001f0000 >;
+			};
+		};
+	};
+
+	memory-controller@7000f400 {
+		emc-timings-2 {
+			/* Hynix 1GB H9TCNNN8JDMMPR LPDDR2 533MHz */
+			nvidia,ram-code = <2>;
+
+			timing-12750000 {
+				clock-frequency = <12750000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000000
+					0x00000001 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x00000009 0x0000002f 0x00000000 0x0000000b
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000002 0x00000002
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x00000036 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000009 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000164 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000003 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x00000009 0x00000060 0x00000000 0x00000018
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000004 0x00000004
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x0000006b 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x0000000a 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x800001c5 0xd0000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000003
+					0x00000006 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x00000009 0x000000c0 0x00000000 0x00000030
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000008 0x00000008
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x000000d5 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000013 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xd0000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x0000000a>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000006
+					0x0000000d 0x00000004 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x00000009 0x00000181 0x00000000 0x00000060
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x0000000f 0x0000000f
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x000001a9 0x00000004 0x00000006
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000025 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xd0000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010042>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000013>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000c
+					0x0000001a 0x00000008 0x00000003 0x00000005
+					0x00000004 0x00000001 0x00000006 0x00000003
+					0x00000003 0x00000002 0x00000002 0x00000000
+					0x00000001 0x00000004 0x00000001 0x0000000c
+					0x0000000a 0x00000303 0x00000000 0x000000c0
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000007 0x0000001d 0x0000001d
+					0x00000004 0x0000000b 0x00000005 0x00000004
+					0x00000002 0x00000351 0x00000005 0x00000004
+					0x00000000 0x00000000 0x00004282 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00072000 0x00072000 0x00072000
+					0x00072000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000e0220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x0000004a 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-266500000 {
+				clock-frequency = <266500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010042>;
+				nvidia,emc-mode-2 = <0x00020002>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000018>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000f
+					0x00000022 0x0000000b 0x00000004 0x00000005
+					0x00000005 0x00000001 0x00000007 0x00000004
+					0x00000004 0x00000002 0x00000002 0x00000000
+					0x00000002 0x00000005 0x00000002 0x0000000c
+					0x0000000b 0x000003ef 0x00000000 0x000000fb
+					0x00000001 0x00000001 0x00000004 0x00000000
+					0x00000001 0x00000009 0x00000026 0x00000026
+					0x00000004 0x0000000e 0x00000006 0x00000004
+					0x00000002 0x00000455 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00006282 0x003200a4
+					0x00008000 0x00070000 0x00070000 0x00070000
+					0x00070000 0x00072000 0x00072000 0x00072000
+					0x00072000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080002 0x00080002 0x00080002
+					0x00080002 0x000e0220 0x0800003d 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000060 0x000a000a 0xa0f10000 0x00000000
+					0x00000000 0x800008ee 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-533000000 {
+				clock-frequency = <533000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x000100c2>;
+				nvidia,emc-mode-2 = <0x00020006>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000030>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000001f
+					0x00000045 0x00000016 0x00000009 0x00000008
+					0x00000009 0x00000003 0x0000000d 0x00000009
+					0x00000009 0x00000005 0x00000003 0x00000000
+					0x00000004 0x0000000a 0x00000006 0x0000000d
+					0x00000010 0x000007df 0x00000000 0x000001f7
+					0x00000003 0x00000003 0x00000009 0x00000000
+					0x00000001 0x0000000f 0x0000004b 0x0000004b
+					0x00000008 0x0000001b 0x0000000c 0x00000004
+					0x00000002 0x000008aa 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00006282 0xf0120091
+					0x00008000 0x0000000c 0x0000000c 0x0000000c
+					0x0000000c 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000c 0x0000000c 0x0000000c
+					0x0000000c 0x000c0220 0x0800003d 0x00000000
+					0x77ffc004 0x01f1f408 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x000000c0 0x000e000e 0xa0f10000 0x00000000
+					0x00000000 0x800010d9 0xe0000000 0xff00ff88 >;
+			};
+		};
+	};
+
+	battery: battery-cell {
+		compatible = "simple-battery";
+		device-chemistry = "lithium-ion";
+		charge-full-design-microamp-hours = <2080000>;
+		energy-full-design-microwatt-hours = <7700000>;
+		operating-range-celsius = <0 45>;
+	};
+
+	gpio-keys {
+		key-memo {
+			label = "Memo";
+			gpios = <&gpio TEGRA_GPIO(B, 6) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_MEMO>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio TEGRA_GPIO(I, 6) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+	};
+
+	gpio-leds {
+		led-power {
+			label = "power::white";
+			gpios = <&gpio TEGRA_GPIO(R, 3) GPIO_ACTIVE_HIGH>;
+
+			linux,default-trigger = "battery-charging";
+
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_CHARGING;
+		};
+	};
+
+	regulator-lcd3v {
+		gpio = <&gpio TEGRA_GPIO(BB, 0) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	sound {
+		compatible = "lg,tegra-audio-max98089-p895",
+			     "nvidia,tegra-audio-max98089";
+		nvidia,model = "LG Optimus Vu MAX98089";
+
+		nvidia,int-mic-en-gpios = <&gpio TEGRA_GPIO(I, 2) GPIO_ACTIVE_HIGH>;
+	};
+};
diff --git a/arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi b/arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi
new file mode 100644
index 000000000000..909260a5d0fb
--- /dev/null
+++ b/arch/arm/boot/dts/nvidia/tegra30-lg-x3.dtsi
@@ -0,0 +1,1812 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/mfd/max77620.h>
+#include <dt-bindings/thermal/thermal.h>
+
+#include "tegra30.dtsi"
+#include "tegra30-cpu-opp.dtsi"
+#include "tegra30-cpu-opp-microvolt.dtsi"
+
+/ {
+	chassis-type = "handset";
+
+	aliases {
+		mmc0 = &sdmmc4; /* eMMC */
+		mmc1 = &sdmmc1; /* WiFi */
+
+		rtc0 = &pmic;
+		rtc1 = "/rtc@7000e000";
+
+		serial0 = &uartd; /* Console */
+		serial1 = &uartc; /* Bluetooth */
+		serial2 = &uartb; /* GPS */
+	};
+
+	/*
+	 * The decompressor and also some bootloaders rely on a
+	 * pre-existing /chosen node to be available to insert the
+	 * command line and merge other ATAGS info.
+	 */
+	chosen { };
+
+	firmware {
+		trusted-foundations {
+			compatible = "tlm,trusted-foundations";
+			tlm,version-major = <2>;
+			tlm,version-minor = <8>;
+		};
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		linux,cma@80000000 {
+			compatible = "shared-dma-pool";
+			alloc-ranges = <0x80000000 0x30000000>;
+			size = <0x10000000>;		/* 256MiB */
+			linux,cma-default;
+			reusable;
+		};
+
+		ramoops@bed00000 {
+			compatible = "ramoops";
+			reg = <0xbed00000 0x10000>;	/* 64kB */
+			console-size = <0x8000>;	/* 32kB */
+			record-size = <0x400>;		/* 1kB */
+			ecc-size = <16>;
+		};
+
+		trustzone@bfe00000 {
+			reg = <0xbfe00000 0x200000>;	/* 2MB */
+			no-map;
+		};
+	};
+
+	vde@6001a000 {
+		assigned-clocks = <&tegra_car TEGRA30_CLK_VDE>;
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_P>;
+		assigned-clock-rates = <408000000>;
+	};
+
+	pinmux@70000868 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&state_default>;
+
+		state_default: pinmux {
+			/* WLAN SDIO pinmux */
+			sdmmc1-clk {
+				nvidia,pins = "sdmmc1_clk_pz0";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			sdmmc1-cmd {
+				nvidia,pins = "sdmmc1_cmd_pz1",
+						"sdmmc1_dat3_py4",
+						"sdmmc1_dat2_py5",
+						"sdmmc1_dat1_py6",
+						"sdmmc1_dat0_py7";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			wlan-reset {
+				nvidia,pins = "pv3";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			wlan-host-wake {
+				nvidia,pins = "pu6";
+				nvidia,function = "pwm3";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* GNSS UART-B pinmux */
+			gps-pwr-en {
+				nvidia,pins = "kb_row6_pr6";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			gps-ldo-en {
+				nvidia,pins = "ulpi_dir_py1";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			gps-clk-ref {
+				nvidia,pins = "gmi_ad8_ph0";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* Bluetooth UART-C pinmux */
+			uartc-cts-rxd {
+				nvidia,pins = "uart3_cts_n_pa1",
+						"uart3_rxd_pw7";
+				nvidia,function = "uartc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			uartc-rts-txd {
+				nvidia,pins = "uart3_rts_n_pc0",
+						"uart3_txd_pw6";
+				nvidia,function = "uartc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			bt-reset {
+				nvidia,pins = "clk2_req_pcc5";
+				nvidia,function = "dap";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			bt-dev-wake {
+				nvidia,pins = "kb_row11_ps3";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			bt-host-wake {
+				nvidia,pins = "kb_row12_ps4";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			bt-pcm-dap4 {
+				nvidia,pins = "dap4_fs_pp4",
+						"dap4_din_pp5",
+						"dap4_dout_pp6",
+						"dap4_sclk_pp7";
+				nvidia,function = "i2s3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* EMMC pinmux */
+			sdmmc4-clk {
+				nvidia,pins = "sdmmc4_clk_pcc4";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			sdmmc4-data {
+				nvidia,pins = "sdmmc4_cmd_pt7",
+						"sdmmc4_dat0_paa0",
+						"sdmmc4_dat1_paa1",
+						"sdmmc4_dat2_paa2",
+						"sdmmc4_dat3_paa3",
+						"sdmmc4_dat4_paa4",
+						"sdmmc4_dat5_paa5",
+						"sdmmc4_dat6_paa6",
+						"sdmmc4_dat7_paa7";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			sdmmc4-reset {
+				nvidia,pins = "sdmmc4_rst_n_pcc3";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* I2C pinmux */
+			gen1-i2c {
+				nvidia,pins = "gen1_i2c_scl_pc4",
+						"gen1_i2c_sda_pc5";
+				nvidia,function = "i2c1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <TEGRA_PIN_DISABLE>;
+			};
+			gen2-i2c {
+				nvidia,pins = "gen2_i2c_scl_pt5",
+						"gen2_i2c_sda_pt6";
+				nvidia,function = "i2c2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <TEGRA_PIN_DISABLE>;
+			};
+			cam-i2c {
+				nvidia,pins = "cam_i2c_scl_pbb1",
+						"cam_i2c_sda_pbb2";
+				nvidia,function = "i2c3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <TEGRA_PIN_DISABLE>;
+			};
+			ddc-i2c {
+				nvidia,pins = "ddc_scl_pv4",
+						"ddc_sda_pv5";
+				nvidia,function = "i2c4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <TEGRA_PIN_DISABLE>;
+			};
+			pwr-i2c {
+				nvidia,pins = "pwr_i2c_scl_pz6",
+						"pwr_i2c_sda_pz7";
+				nvidia,function = "i2cpwr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <TEGRA_PIN_DISABLE>;
+			};
+			mhl-i2c {
+				nvidia,pins = "kb_col6_pq6",
+						"kb_col7_pq7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* GPIO keys pinmux */
+			power-key {
+				nvidia,pins = "gmi_wp_n_pc7";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			volume-down {
+				nvidia,pins = "ulpi_data3_po4";
+				nvidia,function = "spi3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Sensors pinmux */
+			sen-vdd {
+				nvidia,pins = "spi1_miso_px7";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			proxi-vdd {
+				nvidia,pins = "spi2_miso_px1";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			sen-vio {
+				nvidia,pins = "lcd_dc1_pd2";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			nct-irq {
+				nvidia,pins = "gmi_iordy_pi5";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			bat-irq {
+				nvidia,pins = "kb_row8_ps0";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			charger-irq {
+				nvidia,pins = "gmi_cs1_n_pj2";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			mpu-irq {
+				nvidia,pins = "gmi_ad12_ph4";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			compass-irq {
+				nvidia,pins = "gmi_ad13_ph5";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			light-irq {
+				nvidia,pins = "gmi_cs4_n_pk2";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* LED pinmux */
+			backlight-en {
+				nvidia,pins = "lcd_dc0_pn6";
+				nvidia,function = "rsvd3";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			flash-led-en {
+				nvidia,pins = "pbb3";
+				nvidia,function = "vgp3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			keypad-led {
+				nvidia,pins = "kb_row2_pr2",
+						"kb_row3_pr3";
+				nvidia,function = "rsvd3";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* NFC pinmux */
+			nfc-irq {
+				nvidia,pins = "spi2_cs1_n_pw2";
+				nvidia,function = "spi2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			nfc-ven {
+				nvidia,pins = "spi1_sck_px5";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			nfc-firm {
+				nvidia,pins = "kb_row0_pr0";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* DC pinmux */
+			lcd-pwr {
+				nvidia,pins = "lcd_pwr0_pb2",
+						"lcd_pwr1_pc1";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			lcd-wr-n {
+				nvidia,pins = "lcd_wr_n_pz3";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			lcd-id {
+				nvidia,pins = "lcd_m1_pw1";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			lcd-pclk {
+				nvidia,pins = "lcd_pclk_pb3",
+						"lcd_de_pj1",
+						"lcd_hsync_pj3",
+						"lcd_vsync_pj4";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			lcd-rgb-blue {
+				nvidia,pins = "lcd_d0_pe0",
+						"lcd_d1_pe1",
+						"lcd_d2_pe2",
+						"lcd_d3_pe3",
+						"lcd_d4_pe4",
+						"lcd_d5_pe5",
+						"lcd_d18_pm2",
+						"lcd_d19_pm3";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			lcd-rgb-green {
+				nvidia,pins = "lcd_d6_pe6",
+						"lcd_d7_pe7",
+						"lcd_d8_pf0",
+						"lcd_d9_pf1",
+						"lcd_d10_pf2",
+						"lcd_d11_pf3",
+						"lcd_d20_pm4",
+						"lcd_d21_pm5";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			lcd-rgb-red {
+				nvidia,pins = "lcd_d12_pf4",
+						"lcd_d13_pf5",
+						"lcd_d14_pf6",
+						"lcd_d15_pf7",
+						"lcd_d16_pm0",
+						"lcd_d17_pm1",
+						"lcd_d22_pm6",
+						"lcd_d23_pm7";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Bridge pinmux */
+			bridge-reset {
+				nvidia,pins = "ulpi_data1_po2";
+				nvidia,function = "spi3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			rgb-ic-en {
+				nvidia,pins = "gmi_a18_pb1";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			bridge-clk {
+				nvidia,pins = "clk3_out_pee0";
+				nvidia,function = "extperiph3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			rgb-bridge {
+				nvidia,pins = "lcd_sdin_pz2",
+						"lcd_sdout_pn5",
+						"lcd_cs0_n_pn4",
+						"lcd_sck_pz4";
+				nvidia,function = "spi5";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Panel pinmux */
+			panel-reset {
+				nvidia,pins = "lcd_cs1_n_pw0";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			panel-vio {
+				nvidia,pins = "ulpi_clk_py0";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* Touchscreen pinmux */
+			touch-vdd {
+				nvidia,pins = "kb_col1_pq1";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			touch-vio {
+				nvidia,pins = "spi1_mosi_px4";
+				nvidia,function = "spi2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			touch-irq-n {
+				nvidia,pins = "kb_col3_pq3";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			touch-rst-n {
+				nvidia,pins = "ulpi_data0_po1";
+				nvidia,function = "spi3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			touch-maker-id {
+				nvidia,pins = "kb_col2_pq2";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* MHL pinmux */
+			mhl-vio {
+				nvidia,pins = "pv2";
+				nvidia,function = "owr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			mhl-rst-n {
+				nvidia,pins = "clk3_req_pee1";
+				nvidia,function = "dev3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			mhl-irq {
+				nvidia,pins = "crt_vsync_pv7";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			mhl-sel {
+				nvidia,pins = "kb_row10_ps2";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			hdmi-hpd {
+				nvidia,pins = "hdmi_int_pn7";
+				nvidia,function = "hdmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* AUDIO pinmux */
+			hp-detect {
+				nvidia,pins = "pbb6";
+				nvidia,function = "vgp6";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			hp-hook {
+				nvidia,pins = "ulpi_data4_po5";
+				nvidia,function = "ulpi";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			ear-mic-en {
+				nvidia,pins = "spi2_mosi_px0";
+				nvidia,function = "spi2";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			audio-irq {
+				nvidia,pins = "spi2_cs2_n_pw3";
+				nvidia,function = "spi3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			audio-mclk {
+				nvidia,pins = "clk1_out_pw4";
+				nvidia,function = "extperiph1";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			dap-i2s0 {
+				nvidia,pins = "dap1_fs_pn0",
+						"dap1_din_pn1",
+						"dap1_dout_pn2",
+						"dap1_sclk_pn3";
+				nvidia,function = "i2s0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			dap-i2s1 {
+				nvidia,pins = "dap2_fs_pa2",
+						"dap2_sclk_pa3",
+						"dap2_din_pa4",
+						"dap2_dout_pa5";
+				nvidia,function = "i2s1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* MUIC pinmux */
+			muic-irq {
+				nvidia,pins = "gmi_cs0_n_pj0";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			muic-dp2t {
+				nvidia,pins = "pcc2";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			muic-usif {
+				nvidia,pins = "ulpi_stp_py3";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			ifx-usb-vbus-en {
+				nvidia,pins = "kb_row4_pr4";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			pcb-rev {
+				nvidia,pins = "gmi_wait_pi7",
+						"gmi_rst_n_pi4";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			jtag-rtck {
+				nvidia,pins = "jtag_rtck_pu7";
+				nvidia,function = "rtck";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* Camera pinmux */
+			cam-mclk {
+				nvidia,pins = "cam_mclk_pcc0";
+				nvidia,function = "vi_alt3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			cam-pmic-en {
+				nvidia,pins = "pbb4";
+				nvidia,function = "vgp4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			front-cam-rst {
+				nvidia,pins = "pbb5";
+				nvidia,function = "vgp5";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			front-cam-vio {
+				nvidia,pins = "ulpi_nxt_py2";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			rear-cam-rst {
+				nvidia,pins = "gmi_cs3_n_pk4";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			rear-cam-eprom-pr {
+				nvidia,pins = "gmi_cs2_n_pk3";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			rear-cam-vcm-pwdn {
+				nvidia,pins = "kb_row1_pr1";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Haptic pinmux */
+			haptic-en {
+				nvidia,pins = "gmi_ad9_ph1";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			haptic-osc {
+				nvidia,pins = "gmi_ad11_ph3";
+				nvidia,function = "pwm3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* Modem pinmux */
+			cp2ap-ack1-host-active {
+				nvidia,pins = "pu5";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			cp2ap-ack2-host-wakeup {
+				nvidia,pins = "pv0";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			ap2cp-ack2-suspend-req {
+				nvidia,pins = "kb_row14_ps6";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			ap2cp-ack1-slave-wakeup {
+				nvidia,pins = "kb_row15_ps7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			cp-kkp {
+				nvidia,pins = "kb_col0_pq0";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			cp-crash-irq {
+				nvidia,pins = "kb_row13_ps5";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			ap2cp-uarta-tx-ipc {
+				nvidia,pins = "pu0";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			ap2cp-uarta-rx-ipc {
+				nvidia,pins = "pu1";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			fota-ap-cts-cp-rts {
+				nvidia,pins = "pu2";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			fota-ap-rts-cp-cts {
+				nvidia,pins = "pu3";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+			modem-enable {
+				nvidia,pins = "ulpi_data7_po0";
+				nvidia,function = "hsi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			modem-reset {
+				nvidia,pins = "pv1";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+			dap-i2s2 {
+				nvidia,pins = "dap3_fs_pp0",
+						"dap3_din_pp1",
+						"dap3_dout_pp2",
+						"dap3_sclk_pp3";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* GPIO power/drive control */
+			drive-i2c {
+				nvidia,pins = "drive_dbg",
+						"drive_at5",
+						"drive_gme",
+						"drive_ddc",
+						"drive_ao1";
+				nvidia,high-speed-mode = <TEGRA_PIN_DISABLE>;
+				nvidia,schmitt = <TEGRA_PIN_ENABLE>;
+				nvidia,low-power-mode = <TEGRA_PIN_LP_DRIVE_DIV_1>;
+				nvidia,pull-down-strength = <31>;
+				nvidia,pull-up-strength = <31>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+			};
+
+			drive-uart3 {
+				nvidia,pins = "drive_uart3";
+				nvidia,high-speed-mode = <TEGRA_PIN_DISABLE>;
+				nvidia,schmitt = <TEGRA_PIN_ENABLE>;
+				nvidia,low-power-mode = <TEGRA_PIN_LP_DRIVE_DIV_1>;
+				nvidia,pull-down-strength = <31>;
+				nvidia,pull-up-strength = <31>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+			};
+
+			drive-gmi {
+				nvidia,pins = "drive_at3";
+				nvidia,high-speed-mode = <TEGRA_PIN_DISABLE>;
+				nvidia,schmitt = <TEGRA_PIN_ENABLE>;
+				nvidia,low-power-mode = <TEGRA_PIN_LP_DRIVE_DIV_1>;
+				nvidia,pull-down-strength = <31>;
+				nvidia,pull-up-strength = <31>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+			};
+		};
+	};
+
+	uartb: serial@70006040 {
+		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
+		status = "okay";
+
+		/* GNSS GSD5T */
+	};
+
+	uartc: serial@70006200 {
+		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
+		/delete-property/ reg-shift;
+		status = "okay";
+
+		nvidia,adjust-baud-rates = <0 9600 100>,
+					   <9600 115200 200>,
+					   <1000000 4000000 136>;
+
+		/* BCM4330B1 37.4 MHz Class 1.5 ExtLNA */
+		bluetooth {
+			compatible = "brcm,bcm4330-bt";
+			max-speed = <4000000>;
+
+			clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
+			clock-names = "txco";
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(S, 4) IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "host-wakeup";
+
+			device-wakeup-gpios = <&gpio TEGRA_GPIO(S, 3) GPIO_ACTIVE_HIGH>;
+			shutdown-gpios = <&gpio TEGRA_GPIO(CC, 5) GPIO_ACTIVE_HIGH>;
+
+			vbat-supply = <&vdd_3v3_vbat>;
+			vddio-supply = <&vdd_1v8_vio>;
+		};
+	};
+
+	uartd: serial@70006300 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
+		status = "okay";
+
+		/* Console */
+	};
+
+	pwm@7000a000 {
+		status = "okay";
+	};
+
+	gen1_i2c: i2c@7000c000 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		/* Aichi AMI306 digital compass */
+		magnetometer@e {
+			compatible = "asahi-kasei,ak8974";
+			reg = <0x0e>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(H, 5) IRQ_TYPE_EDGE_RISING>;
+
+			avdd-supply = <&vdd_3v0_sen>;
+			dvdd-supply = <&vdd_1v8_vio>;
+
+			mount-matrix = "-1",  "0",  "0",
+					"0",  "1",  "0",
+					"0",  "0", "-1";
+		};
+
+		max98089: audio-codec@10 {
+			compatible = "maxim,max98089";
+			reg = <0x10>;
+
+			clocks = <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+			clock-names = "mclk";
+
+			assigned-clocks = <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+			assigned-clock-parents = <&tegra_car TEGRA30_CLK_EXTERN1>;
+		};
+
+		nfc@28 {
+			compatible = "nxp,pn544-i2c";
+			reg = <0x28>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(W, 2) IRQ_TYPE_EDGE_RISING>;
+
+			enable-gpios = <&gpio TEGRA_GPIO(X, 5) GPIO_ACTIVE_HIGH>;
+			firmware-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>;
+		};
+
+		imu@68 {
+			compatible = "invensense,mpu6050";
+			reg = <0x68>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(H, 4) IRQ_TYPE_EDGE_RISING>;
+
+			vdd-supply = <&vdd_3v0_sen>;
+			vddio-supply = <&vdd_1v8_sen>;
+
+			mount-matrix =  "1",  "0",  "0",
+					"0",  "1",  "0",
+					"0",  "0", "-1";
+		};
+	};
+
+	gen2_i2c: i2c@7000c400 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		/* Synaptics RMI4 S3203B touchcreen */
+		touchscreen@20 {
+			compatible = "syna,rmi4-i2c";
+			reg = <0x20>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(Q, 3) IRQ_TYPE_EDGE_FALLING>;
+
+			vdd-supply = <&vdd_3v0_touch>;
+			vio-supply = <&vdd_1v8_touch>;
+
+			syna,reset-delay-ms = <20>;
+			syna,startup-delay-ms = <200>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			rmi4-f01@1 {
+				reg = <0x1>;
+				syna,nosleep-mode = <1>;
+			};
+
+			rmi4-f11@11 {
+				reg = <0x11>;
+				syna,sensor-type = <1>;
+
+				syna,clip-x-low = <0>;
+				syna,clip-y-low = <0>;
+			};
+		};
+	};
+
+	cam_i2c: i2c@7000c500 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		dw9714: coil@c {
+			compatible = "dongwoon,dw9714";
+			reg = <0x0c>;
+
+			enable-gpios = <&gpio TEGRA_GPIO(R, 1) GPIO_ACTIVE_HIGH>;
+
+			vcc-supply = <&vcc_focuser>;
+		};
+
+		camera-pmic@7d {
+			compatible = "ti,lp8720";
+			reg = <0x7d>;
+
+			enable-gpios = <&gpio TEGRA_GPIO(BB, 4) GPIO_ACTIVE_HIGH>;
+
+			vt_1v2_front: ldo1 {
+				regulator-name = "vt_1v2_dig";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+			};
+
+			vt_2v7_front: ldo2 {
+				regulator-name = "vt_2v7_vana";
+				regulator-min-microvolt = <2700000>;
+				regulator-max-microvolt = <2700000>;
+			};
+
+			vdd_2v7_rear: ldo3 {
+				regulator-name = "8m_2v7_vana";
+				regulator-min-microvolt = <2700000>;
+				regulator-max-microvolt = <2800000>;
+			};
+
+			vio_1v8_rear: ldo4 {
+				regulator-name = "vio_1v8_cam";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			vcc_focuser: ldo5 {
+				regulator-name = "8m_2v8_vcm";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+			};
+
+			vdd_1v2_rear: buck {
+				regulator-name = "8m_1v2_cam";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+			};
+		};
+	};
+
+	hdmi_ddc: i2c@7000c700 {
+		status = "okay";
+		clock-frequency = <100000>;
+	};
+
+	pwr_i2c: i2c@7000d000 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		pmic: max77663@1c {
+			compatible = "maxim,max77663";
+			reg = <0x1c>;
+
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+
+			#gpio-cells = <2>;
+			gpio-controller;
+
+			system-power-controller;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&max77663_default>;
+
+			max77663_default: pinmux {
+				gpio1 {
+					pins = "gpio1";
+					function = "gpio";
+					drive-open-drain = <1>;
+				};
+
+				gpio4 {
+					pins = "gpio4";
+					function = "32k-out1";
+				};
+			};
+
+			fps {
+				fps0 {
+					maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>;
+				};
+
+				fps1 {
+					maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN1>;
+				};
+
+				fps2 {
+					maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>;
+				};
+			};
+
+			regulators {
+				in-sd0-supply = <&vdd_5v0_vbus>;
+				in-sd1-supply = <&vdd_5v0_vbus>;
+				in-sd2-supply = <&vdd_5v0_vbus>;
+				in-sd3-supply = <&vdd_5v0_vbus>;
+
+				in-ldo0-1-supply = <&vdd_1v8_vio>;
+				in-ldo2-supply   = <&vdd_3v3_vbat>;
+				in-ldo3-5-supply = <&vdd_3v3_vbat>;
+				in-ldo4-6-supply = <&vdd_3v3_vbat>;
+				in-ldo7-8-supply = <&vdd_1v8_vio>;
+
+				vdd_cpu: sd0 {
+					regulator-name = "vdd_cpu";
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1250000>;
+					regulator-coupled-with = <&vdd_core>;
+					regulator-coupled-max-spread = <300000>;
+					regulator-max-step-microvolt = <100000>;
+					regulator-always-on;
+					regulator-boot-on;
+
+					nvidia,tegra-cpu-regulator;
+					maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+				};
+
+				vdd_core: sd1 {
+					regulator-name = "vdd_core";
+					regulator-min-microvolt = <950000>;
+					regulator-max-microvolt = <1350000>;
+					regulator-coupled-with = <&vdd_cpu>;
+					regulator-coupled-max-spread = <300000>;
+					regulator-max-step-microvolt = <100000>;
+					regulator-always-on;
+					regulator-boot-on;
+
+					nvidia,tegra-core-regulator;
+					maxim,active-fps-source = <MAX77620_FPS_SRC_1>;
+				};
+
+				vdd_1v8_vio: sd2 {
+					regulator-name = "vdd_1v8_gen";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+
+					maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+				};
+
+				sd3 {
+					regulator-name = "vddio_ddr";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+
+					maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+				};
+
+				ldo0 {
+					regulator-name = "avdd_pll";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+
+					maxim,active-fps-source = <MAX77620_FPS_SRC_1>;
+				};
+
+				ldo1 {
+					regulator-name = "vdd_ddr_hs";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+					regulator-boot-on;
+
+					maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+				};
+
+				avdd_3v3_periph: ldo2 {
+					regulator-name = "avdd_usb";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+
+					maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+				};
+
+				vdd_usd: ldo3 {
+					regulator-name = "vdd_sdmmc3";
+					regulator-min-microvolt = <3000000>;
+					regulator-max-microvolt = <3000000>;
+					regulator-always-on;
+
+					maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+				};
+
+				ldo4 {
+					regulator-name = "vdd_rtc";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+
+					maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
+				};
+
+				vcore_emmc: ldo5 {
+					regulator-name = "vdd_ddr_rx";
+					regulator-min-microvolt = <2850000>;
+					regulator-max-microvolt = <2850000>;
+					regulator-always-on;
+					regulator-boot-on;
+
+					maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
+				};
+
+				avdd_1v8_hdmi_pll: ldo6 {
+					regulator-name = "avdd_osc";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+
+					maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+				};
+
+				vdd_1v2_mhl: ldo7 {
+					regulator-name = "vdd_1v2_mhl";
+					regulator-min-microvolt = <1050000>;
+					regulator-max-microvolt = <1250000>;
+
+					maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+				};
+
+				ldo8 {
+					regulator-name = "avdd_dsi_csi";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+
+					maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+				};
+			};
+		};
+
+		fuel-gauge@36 {
+			compatible = "maxim,max17043";
+			reg = <0x36>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(S, 0) IRQ_TYPE_EDGE_FALLING>;
+
+			monitored-battery = <&battery>;
+
+			maxim,alert-low-soc-level = <10>;
+			wakeup-source;
+		};
+
+		power-sensor@40 {
+			compatible = "ti,ina230";
+			reg = <0x40>;
+
+			vs-supply = <&vdd_3v0_sen>;
+		};
+
+		nct72: temperature-sensor@4c {
+			compatible = "onnn,nct1008";
+			reg = <0x4c>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(I, 5) IRQ_TYPE_EDGE_FALLING>;
+
+			vcc-supply = <&vdd_3v0_sen>;
+			#thermal-sensor-cells = <1>;
+		};
+	};
+
+	i2c-mhl {
+		compatible = "i2c-gpio";
+
+		sda-gpios = <&gpio TEGRA_GPIO(Q, 7) (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio TEGRA_GPIO(Q, 6) (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+		i2c-gpio,delay-us = <5>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	spi@7000dc00 {
+		status = "okay";
+		spi-max-frequency = <25000000>;
+
+		/* DSI bridge */
+	};
+
+	pmc@7000e400 {
+		status = "okay";
+		nvidia,invert-interrupt;
+		nvidia,suspend-mode = <2>;
+		nvidia,cpu-pwr-good-time = <2000>;
+		nvidia,cpu-pwr-off-time = <200>;
+		nvidia,core-pwr-good-time = <3845 3845>;
+		nvidia,core-pwr-off-time = <0>;
+		nvidia,core-power-req-active-high;
+		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
+
+		i2c-thermtrip {
+			nvidia,i2c-controller-id = <4>;
+			nvidia,bus-addr = <0x1c>;
+			nvidia,reg-addr = <0x41>;
+			nvidia,reg-data = <0x02>;
+		};
+	};
+
+	hda@70030000 {
+		status = "okay";
+	};
+
+	ahub@70080000 {
+		/* HIFI CODEC */
+		i2s@70080300 {		/* i2s0 */
+			status = "okay";
+		};
+
+		/* BASEBAND */
+		i2s@70080500 {		/* i2s2 */
+			status = "okay";
+		};
+
+		/* BT SCO */
+		i2s@70080600 {		/* i2s3 */
+			status = "okay";
+		};
+	};
+
+	sdmmc1: mmc@78000000 {
+		status = "okay";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		assigned-clocks = <&tegra_car TEGRA30_CLK_SDMMC1>;
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_C>;
+		assigned-clock-rates = <50000000>;
+
+		max-frequency = <50000000>;
+		keep-power-in-suspend;
+		bus-width = <4>;
+		non-removable;
+
+		mmc-pwrseq = <&brcm_wifi_pwrseq>;
+		vmmc-supply = <&vdd_3v3_vbat>;
+		vqmmc-supply = <&vdd_1v8_vio>;
+
+		/* BCM4330B1 37.4 MHz Class 1.5 ExtLNA */
+		wifi@1 {
+			compatible = "brcm,bcm4329-fmac";
+			reg = <1>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(U, 6) IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "host-wake";
+		};
+	};
+
+	sdmmc4: mmc@78000600 {
+		status = "okay";
+		bus-width = <8>;
+
+		non-removable;
+		mmc-ddr-1_8v;
+
+		vmmc-supply = <&vcore_emmc>;
+		vqmmc-supply = <&vdd_1v8_vio>;
+	};
+
+	/* Micro USB */
+	usb@7d000000 {
+		compatible = "nvidia,tegra30-udc";
+		status = "okay";
+		dr_mode = "peripheral";
+	};
+
+	usb-phy@7d000000 {
+		status = "okay";
+		dr_mode = "peripheral";
+		nvidia,hssync-start-delay = <0>;
+		nvidia,xcvr-lsfslew = <2>;
+		nvidia,xcvr-lsrslew = <2>;
+		vbus-supply = <&avdd_3v3_periph>;
+	};
+
+	/* PMIC has a built-in 32KHz oscillator which is used by PMC */
+	clk32k_in: clock-32k {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "pmic-oscillator";
+	};
+
+	gps_refclk: clock-gps {
+		compatible = "fixed-clock";
+		clock-frequency = <26000000>;
+		clock-accuracy = <100>;
+		#clock-cells = <0>;
+	};
+
+	gps_osc: clock-gps-osc-gate {
+		compatible = "gpio-gate-clock";
+		enable-gpios = <&gpio TEGRA_GPIO(H, 0) GPIO_ACTIVE_HIGH>;
+		clocks = <&gps_refclk>;
+		#clock-cells = <0>;
+	};
+
+	cpus {
+		cpu0: cpu@0 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+		cpu1: cpu@1 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+		cpu2: cpu@2 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+		cpu3: cpu@3 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-power {
+			label = "Power";
+			gpios = <&gpio TEGRA_GPIO(C, 7) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio TEGRA_GPIO(O, 4) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		led-keypad {
+			label = "keypad::white";
+			gpios = <&gpio TEGRA_GPIO(R, 2) GPIO_ACTIVE_HIGH>;
+
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_KBD_BACKLIGHT;
+		};
+	};
+
+	opp-table-actmon {
+		/delete-node/ opp-625000000;
+		/delete-node/ opp-667000000;
+		/delete-node/ opp-750000000;
+		/delete-node/ opp-800000000;
+		/delete-node/ opp-900000000;
+	};
+
+	opp-table-emc {
+		/delete-node/ opp-625000000-1200;
+		/delete-node/ opp-625000000-1250;
+		/delete-node/ opp-667000000-1200;
+		/delete-node/ opp-750000000-1300;
+		/delete-node/ opp-800000000-1300;
+		/delete-node/ opp-900000000-1350;
+	};
+
+	brcm_wifi_pwrseq: pwrseq-wifi {
+		compatible = "mmc-pwrseq-simple";
+
+		clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
+		clock-names = "ext_clock";
+
+		reset-gpios = <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <300>;
+		power-off-delay-us = <300>;
+	};
+
+	vdd_5v0_vbus: regulator-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_3v3_vbat: regulator-vbat {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_vbat";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd_5v0_vbus>;
+	};
+
+	vdd_3v0_sen: regulator-sen3v {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v0_sensor";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		regulator-boot-on;
+		gpio = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_vbat>;
+	};
+
+	vdd_3v0_proxi: regulator-proxi {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v0_proxi";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		regulator-boot-on;
+		gpio = <&gpio TEGRA_GPIO(X, 1) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_vbat>;
+	};
+
+	vdd_1v8_sen: regulator-sen1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_1v8_sensor";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		gpio = <&gpio TEGRA_GPIO(D, 2) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_vbat>;
+	};
+
+	vcc_3v0_lcd: regulator-lcd3v {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_3v0_lcd";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		regulator-boot-on;
+		vin-supply = <&vdd_3v3_vbat>;
+	};
+
+	iovcc_1v8_lcd: regulator-lcd1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "iovcc_1v8_lcd";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		gpio = <&gpio TEGRA_GPIO(Y, 0) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_vbat>;
+	};
+
+	vio_1v8_mhl: regulator-mhl1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "vio_1v8_mhl";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		gpio = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_vbat>;
+	};
+
+	vdd_3v0_touch: regulator-touchpwr {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v0_touch";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		regulator-boot-on;
+		gpio = <&gpio TEGRA_GPIO(Q, 1) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_vbat>;
+	};
+
+	vdd_1v8_touch: regulator-touchvio {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_1v8_touch";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		gpio = <&gpio TEGRA_GPIO(X, 4) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_vbat>;
+	};
+
+	vcc_1v8_gps: regulator-gps {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_1v8_gps";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		gpio = <&gpio TEGRA_GPIO(Y, 1) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_vbat>;
+	};
+
+	vio_1v8_front: regulator-frontvio {
+		compatible = "regulator-fixed";
+		regulator-name = "vt_1v8_cam_vio";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio TEGRA_GPIO(Y, 2) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_vbat>;
+	};
+
+	sound {
+		nvidia,audio-routing =
+			"Headphone Jack", "HPL",
+			"Headphone Jack", "HPR",
+			"Int Spk", "SPKL",
+			"Int Spk", "SPKR",
+			"Earpiece", "RECL",
+			"Earpiece", "RECR",
+			"INA1", "Mic Jack",
+			"MIC1", "MICBIAS",
+			"MICBIAS", "Internal Mic 1",
+			"MIC2", "Internal Mic 2";
+
+		nvidia,i2s-controller = <&tegra_i2s0>;
+		nvidia,audio-codec = <&max98089>;
+
+		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(BB, 6) GPIO_ACTIVE_LOW>;
+		nvidia,mic-det-gpios = <&gpio TEGRA_GPIO(O, 5) GPIO_ACTIVE_HIGH>;
+		nvidia,ext-mic-en-gpios = <&gpio TEGRA_GPIO(X, 0) GPIO_ACTIVE_HIGH>;
+		nvidia,coupled-mic-hp-det;
+
+		clocks = <&tegra_car TEGRA30_CLK_PLL_A>,
+			 <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
+			 <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+		clock-names = "pll_a", "pll_a_out0", "mclk";
+
+		assigned-clocks = <&tegra_car TEGRA30_CLK_EXTERN1>,
+				  <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
+					 <&tegra_car TEGRA30_CLK_EXTERN1>;
+	};
+
+	thermal-zones {
+		/*
+		 * NCT72 has two sensors:
+		 *
+		 *	0: internal that monitors ambient/skin temperature
+		 *	1: external that is connected to the CPU's diode
+		 *
+		 * Ideally we should use userspace thermal governor,
+		 * but it's a much more complex solution. The "skin"
+		 * zone exists as a simpler solution which prevents
+		 * this device from getting too hot from a user's
+		 * tactile perspective. The CPU zone is intended to
+		 * protect silicon from damage.
+		 */
+
+		skin-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct72 0>;
+
+			trips {
+				trip0: skin-alert {
+					/* throttle at 50C until temperature drops to 49.8C */
+					temperature = <50000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip1: skin-crit {
+					/* shut down at 60C */
+					temperature = <60000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&trip0>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&actmon THERMAL_NO_LIMIT
+								  THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		cpu-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct72 1>;
+
+			trips {
+				trip2: cpu-alert {
+					/* throttle at 75C until temperature drops to 74.8C */
+					temperature = <75000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip3: cpu-crit {
+					/* shut down at 90C */
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map1 {
+					trip = <&trip2>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&actmon THERMAL_NO_LIMIT
+								  THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/tegra30-ouya.dts b/arch/arm/boot/dts/nvidia/tegra30-ouya.dts
index e58dda4f9d2c..7e3de26ca960 100644
--- a/arch/arm/boot/dts/tegra30-ouya.dts
+++ b/arch/arm/boot/dts/nvidia/tegra30-ouya.dts
@@ -26,6 +26,14 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	firmware {
+		trusted-foundations {
+			compatible = "tlm,trusted-foundations";
+			tlm,version-major = <0x0>;
+			tlm,version-minor = <0x0>;
+		};
+	};
+
 	memory@80000000 {
 		reg = <0x80000000 0x40000000>;
 	};
@@ -1996,6 +2004,7 @@
 
 	uartc: serial@70006200 {
 		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 		status = "okay";
 
@@ -2025,6 +2034,8 @@
 	};
 
 	uartd: serial@70006300 {
+		/delete-property/ dmas;
+		/delete-property/ dma-names;
 		status = "okay";
 	};
 
@@ -2037,17 +2048,6 @@
 		status = "okay";
 		clock-frequency = <400000>;
 
-		cpu_temp: nct1008@4c {
-			compatible = "onnn,nct1008";
-			reg = <0x4c>;
-			vcc-supply = <&sys_3v3_reg>;
-
-			interrupt-parent = <&gpio>;
-			interrupts = <TEGRA_GPIO(CC, 2) IRQ_TYPE_EDGE_FALLING>;
-
-			#thermal-sensor-cells = <1>;
-		};
-
 		pmic: pmic@2d {
 			compatible = "ti,tps65911";
 			reg = <0x2d>;
@@ -2161,6 +2161,17 @@
 			};
 		};
 
+		cpu_temp: nct1008@4c {
+			compatible = "onnn,nct1008";
+			reg = <0x4c>;
+			vcc-supply = <&sys_3v3_reg>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(CC, 2) IRQ_TYPE_EDGE_FALLING>;
+
+			#thermal-sensor-cells = <1>;
+		};
+
 		vdd_core: tps62361@60 {
 			compatible = "ti,tps62361";
 			reg = <0x60>;
@@ -4485,17 +4496,6 @@
 		status = "okay";
 	};
 
-	wifi_pwrseq: wifi_pwrseq {
-		compatible = "mmc-pwrseq-simple";
-
-		clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
-		clock-names = "ext_clock";
-
-		reset-gpios = <&gpio TEGRA_GPIO(D, 3) GPIO_ACTIVE_LOW>;
-		post-power-on-delay-ms = <300>;
-		power-off-delay-us = <300>;
-	};
-
 	sdmmc3: mmc@78000400 {
 		status = "okay";
 
@@ -4608,15 +4608,7 @@
 		};
 	};
 
-	firmware {
-		trusted-foundations {
-			compatible = "tlm,trusted-foundations";
-			tlm,version-major = <0x0>;
-			tlm,version-minor = <0x0>;
-		};
-	};
-
-	fan: gpio_fan {
+	fan: fan {
 		compatible = "gpio-fan";
 		gpios = <&gpio TEGRA_GPIO(J, 2) GPIO_ACTIVE_HIGH>;
 		gpio-fan,speed-map = <0    0
@@ -4624,50 +4616,50 @@
 		#cooling-cells = <2>;
 	};
 
-	thermal-zones {
-		cpu_thermal: cpu-thermal {
-			polling-delay = <5000>;
-			polling-delay-passive = <5000>;
+	gpio-keys {
+		compatible = "gpio-keys";
 
-			thermal-sensors = <&cpu_temp 1>;
+		key-power {
+			gpios = <&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_LOW>;
+			debounce-interval = <10>;
+			linux,code = <KEY_POWER>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+	};
 
-			trips {
-				cpu_alert0: cpu-alert0 {
-					temperature = <50000>;
-					hysteresis = <10000>;
-					type = "active";
-				};
-				cpu_alert1: cpu-alert1 {
-					temperature = <70000>;
-					hysteresis = <5000>;
-					type = "passive";
-				};
-				cpu_crit: cpu-crit {
-					temperature = <90000>;
-					hysteresis = <2000>;
-					type = "critical";
-				};
-			};
+	leds {
+		compatible = "gpio-leds";
 
-			cooling-maps {
-				map0 {
-					trip = <&cpu_alert0>;
-					cooling-device = <&fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-				};
-				map1 {
-					trip = <&cpu_alert1>;
-					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-							 <&actmon THERMAL_NO_LIMIT
-								  THERMAL_NO_LIMIT>;
-				};
-			};
+		led-power {
+			label = "power-led";
+			gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+			retain-state-suspended;
 		};
 	};
 
-	vdd_12v_in: vdd_12v_in {
+	opp-table-actmon {
+		/delete-node/ opp-900000000;
+	};
+
+	opp-table-emc {
+		/delete-node/ opp-900000000-1350;
+	};
+
+	wifi_pwrseq: pwrseq-wifi {
+		compatible = "mmc-pwrseq-simple";
+
+		clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
+		clock-names = "ext_clock";
+
+		reset-gpios = <&gpio TEGRA_GPIO(D, 3) GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <300>;
+		power-off-delay-us = <300>;
+	};
+
+	vdd_12v_in: regulator-vdd-12v-in {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_12v_in";
 		regulator-min-microvolt = <12000000>;
@@ -4675,7 +4667,7 @@
 		regulator-always-on;
 	};
 
-	sdmmc_3v3_reg: sdmmc_3v3_reg {
+	sdmmc_3v3_reg: regulator-sdmmc-3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "sdmmc_3v3";
 		regulator-min-microvolt = <3300000>;
@@ -4686,7 +4678,7 @@
 		vin-supply = <&sys_3v3_reg>;
 	};
 
-	vdd_fuse_3v3_reg: vdd_fuse_3v3_reg {
+	vdd_fuse_3v3_reg: regulator-vdd-fuse-3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_fuse_3v3";
 		regulator-min-microvolt = <3300000>;
@@ -4697,7 +4689,7 @@
 		regulator-always-on;
 	};
 
-	vdd_vid_reg: vdd_vid_reg {
+	vdd_vid_reg: regulator-vdd-vid {
 		compatible = "regulator-fixed";
 		regulator-name = "vddio_vid";
 		regulator-min-microvolt = <5000000>;
@@ -4708,7 +4700,7 @@
 		regulator-boot-on;
 	};
 
-	ddr_reg: ddr_reg {
+	ddr_reg: regulator-ddr {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_ddr";
 		regulator-min-microvolt = <1500000>;
@@ -4720,7 +4712,7 @@
 		vin-supply = <&vdd_12v_in>;
 	};
 
-	sys_3v3_reg: sys_3v3_reg {
+	sys_3v3_reg: regulator-sys-3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "sys_3v3";
 		regulator-min-microvolt = <3300000>;
@@ -4732,7 +4724,7 @@
 		vin-supply = <&vdd_12v_in>;
 	};
 
-	vdd_5v0_reg: vdd_5v0_reg {
+	vdd_5v0_reg: regulator-vdd-5v0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_5v0";
 		regulator-min-microvolt = <5000000>;
@@ -4744,14 +4736,14 @@
 		vin-supply = <&vdd_12v_in>;
 	};
 
-	vdd_smsc: vdd_smsc {
+	vdd_smsc: regulator-vdd-smsc {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_smsc";
 		enable-active-high;
 		gpio = <&gpio TEGRA_GPIO(DD, 5) GPIO_ACTIVE_HIGH>;
 	};
 
-	usb3_vbus_reg: usb3_vbus_reg {
+	usb3_vbus_reg: regulator-usb3-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "usb3_vbus";
 		regulator-min-microvolt = <5000000>;
@@ -4761,36 +4753,46 @@
 		vin-supply = <&vdd_5v0_reg>;
 	};
 
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		power {
-			gpios = <&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_LOW>;
-			debounce-interval = <10>;
-			linux,code = <KEY_POWER>;
-			wakeup-event-action = <EV_ACT_ASSERTED>;
-			wakeup-source;
-		};
-	};
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay = <5000>;
+			polling-delay-passive = <5000>;
 
+			thermal-sensors = <&cpu_temp 1>;
 
-	leds {
-		compatible = "gpio-leds";
+			trips {
+				cpu_alert0: cpu-alert0 {
+					temperature = <50000>;
+					hysteresis = <10000>;
+					type = "active";
+				};
+				cpu_alert1: cpu-alert1 {
+					temperature = <70000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+				cpu_crit: cpu-crit {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
 
-		led-power {
-			label = "power-led";
-			gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
-			default-state = "on";
-			linux,default-trigger = "heartbeat";
-			retain-state-suspended;
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert0>;
+					cooling-device = <&fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+				map1 {
+					trip = <&cpu_alert1>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&actmon THERMAL_NO_LIMIT
+								  THERMAL_NO_LIMIT>;
+				};
+			};
 		};
 	};
 };
-
-&emc_icc_dvfs_opp_table {
-	/delete-node/ opp-900000000-1350;
-};
-
-&emc_bw_dfs_opp_table {
-	/delete-node/ opp-900000000;
-};
diff --git a/arch/arm/boot/dts/tegra30-pegatron-chagall.dts b/arch/arm/boot/dts/nvidia/tegra30-pegatron-chagall.dts
index 8ce61035290b..b7d0ebb766a6 100644
--- a/arch/arm/boot/dts/tegra30-pegatron-chagall.dts
+++ b/arch/arm/boot/dts/nvidia/tegra30-pegatron-chagall.dts
@@ -37,6 +37,14 @@
 	 */
 	chosen {};
 
+	firmware {
+		trusted-foundations {
+			compatible = "tlm,trusted-foundations";
+			tlm,version-major = <2>;
+			tlm,version-minor = <8>;
+		};
+	};
+
 	memory@80000000 {
 		reg = <0x80000000 0x40000000>;
 	};
@@ -134,7 +142,7 @@
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
 				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
 				nvidia,lock = <0>;
-				nvidia,ioreset = <0>;
+				nvidia,io-reset = <0>;
 			};
 
 			/* SDMMC3 pinmux */
@@ -150,7 +158,6 @@
 				nvidia,pins = "sdmmc3_cmd_pa7",
 						"sdmmc3_dat3_pb4",
 						"sdmmc3_dat2_pb5",
-						"sdmmc3_dat2_pb5",
 						"sdmmc3_dat1_pb6",
 						"sdmmc3_dat0_pb7",
 						"sdmmc3_dat5_pd0",
@@ -622,7 +629,7 @@
 				nvidia,tristate = <TEGRA_PIN_ENABLE>;
 				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
 				nvidia,lock = <0>;
-				nvidia,ioreset = <0>;
+				nvidia,io-reset = <0>;
 			};
 
 			pu1 {
@@ -689,7 +696,7 @@
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
 				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
 				nvidia,lock = <0>;
-				nvidia,ioreset = <0>;
+				nvidia,io-reset = <0>;
 			};
 
 			vi_d10_pt2 {
@@ -864,7 +871,7 @@
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
 				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
 				nvidia,lock = <0>;
-				nvidia,ioreset = <0>;
+				nvidia,io-reset = <0>;
 			};
 
 			vi_mclk_pt1 {
@@ -1103,6 +1110,7 @@
 
 	uartb: serial@70006040 {
 		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 		status = "okay";
 
@@ -1111,6 +1119,7 @@
 
 	uartc: serial@70006200 {
 		compatible = "nvidia,tegra30-hsuart";
+		reset-names = "serial";
 		/delete-property/ reg-shift;
 		status = "okay";
 
@@ -1146,6 +1155,14 @@
 		status = "okay";
 		clock-frequency = <400000>;
 
+		embedded-controller@10 {
+			compatible = "pegatron,chagall-ec";
+			reg = <0x10>;
+
+			monitored-battery = <&battery>;
+			power-supplies = <&mains>;
+		};
+
 		/* Wolfson Microelectronics WM8903 audio codec */
 		wm8903: audio-codec@1a {
 			compatible = "wlf,wm8903";
@@ -1191,16 +1208,6 @@
 		status = "okay";
 		clock-frequency = <400000>;
 
-		light-sensor@44 {
-			compatible = "isil,isl29023";
-			reg = <0x44>;
-
-			interrupt-parent = <&gpio>;
-			interrupts = <TEGRA_GPIO(Q, 3) IRQ_TYPE_LEVEL_HIGH>;
-
-			vcc-supply = <&vdd_3v3_sen>;
-		};
-
 		/* AsahiKASEI AK8975 magnetometer sensor */
 		magnetometer@c {
 			compatible = "asahi-kasei,ak8975";
@@ -1214,6 +1221,16 @@
 					 "0",  "0", "-1";
 		};
 
+		light-sensor@44 {
+			compatible = "isil,isl29023";
+			reg = <0x44>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(Q, 3) IRQ_TYPE_LEVEL_HIGH>;
+
+			vcc-supply = <&vdd_3v3_sen>;
+		};
+
 		gyroscope@68 {
 			compatible = "invensense,mpu3050";
 			reg = <0x68>;
@@ -1260,17 +1277,6 @@
 		status = "okay";
 		clock-frequency = <400000>;
 
-		nct72: temperature-sensor@4c {
-			compatible = "onnn,nct1008";
-			reg = <0x4c>;
-
-			interrupt-parent = <&gpio>;
-			interrupts = <TEGRA_GPIO(U, 5) IRQ_TYPE_EDGE_FALLING>;
-
-			vcc-supply = <&vdd_3v3_sys>;
-			#thermal-sensor-cells = <1>;
-		};
-
 		/* Texas Instruments TPS659110 PMIC */
 		pmic: pmic@2d {
 			compatible = "ti,tps65911";
@@ -1401,6 +1407,17 @@
 			};
 		};
 
+		nct72: temperature-sensor@4c {
+			compatible = "onnn,nct1008";
+			reg = <0x4c>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(U, 5) IRQ_TYPE_EDGE_FALLING>;
+
+			vcc-supply = <&vdd_3v3_sys>;
+			#thermal-sensor-cells = <1>;
+		};
+
 		vdd_core: core-regulator@60 {
 			compatible = "ti,tps62361";
 			reg = <0x60>;
@@ -2507,17 +2524,6 @@
 		vqmmc-supply = <&vddio_usd>; /* ldo3 */
 	};
 
-	brcm_wifi_pwrseq: wifi-pwrseq {
-		compatible = "mmc-pwrseq-simple";
-
-		clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
-		clock-names = "ext_clock";
-
-		reset-gpios = <&gpio TEGRA_GPIO(D, 3) GPIO_ACTIVE_LOW>;
-		post-power-on-delay-ms = <300>;
-		power-off-delay-us = <300>;
-	};
-
 	sdmmc3: mmc@78000400 {
 		status = "okay";
 
@@ -2598,6 +2604,14 @@
 		default-brightness-level = <15>;
 	};
 
+	battery: battery-cell {
+		compatible = "simple-battery";
+		device-chemistry = "lithium-ion-polymer";
+		charge-full-design-microamp-hours = <3050000>;
+		energy-full-design-microwatt-hours = <23000000>;
+		operating-range-celsius = <0 45>;
+	};
+
 	/* PMIC has a built-in 32KHz oscillator which is used by PMC */
 	clk32k_in: clock-32k {
 		compatible = "fixed-clock";
@@ -2630,7 +2644,7 @@
 	};
 
 	display-panel {
-		compatible = "panel-lvds";
+		compatible = "hannstar,hsd101pww2", "panel-lvds";
 
 		width-mm = <217>;
 		height-mm = <136>;
@@ -2653,9 +2667,8 @@
 
 	extcon-keys {
 		compatible = "gpio-keys";
-		interrupt-parent = <&gpio>;
 
-		dock-insert {
+		switch-dock-insert {
 			label = "Chagall Dock";
 			gpios = <&gpio TEGRA_GPIO(S, 4) GPIO_ACTIVE_LOW>;
 			linux,input-type = <EV_SW>;
@@ -2665,7 +2678,7 @@
 			wakeup-source;
 		};
 
-		lineout-detect {
+		switch-lineout-detect {
 			label = "Audio dock line-out detect";
 			gpios = <&gpio TEGRA_GPIO(S, 3) GPIO_ACTIVE_LOW>;
 			linux,input-type = <EV_SW>;
@@ -2676,19 +2689,10 @@
 		};
 	};
 
-	firmware {
-		trusted-foundations {
-			compatible = "tlm,trusted-foundations";
-			tlm,version-major = <2>;
-			tlm,version-minor = <8>;
-		};
-	};
-
 	gpio-keys {
 		compatible = "gpio-keys";
-		interrupt-parent = <&gpio>;
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -2697,19 +2701,19 @@
 			wakeup-source;
 		};
 
-		volume-up {
-			label = "Volume Up";
-			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEUP>;
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio TEGRA_GPIO(Q, 1) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
 			debounce-interval = <10>;
 			wakeup-event-action = <EV_ACT_ASSERTED>;
 			wakeup-source;
 		};
 
-		volume-down {
-			label = "Volume Down";
-			gpios = <&gpio TEGRA_GPIO(Q, 1) GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEDOWN>;
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
 			debounce-interval = <10>;
 			wakeup-event-action = <EV_ACT_ASSERTED>;
 			wakeup-source;
@@ -2722,6 +2726,34 @@
 		vcc-supply = <&vdd_3v3_sys>;
 	};
 
+	opp-table-actmon {
+		/delete-node/ opp-625000000;
+		/delete-node/ opp-667000000;
+		/delete-node/ opp-750000000;
+		/delete-node/ opp-800000000;
+		/delete-node/ opp-900000000;
+	};
+
+	opp-table-emc {
+		/delete-node/ opp-625000000-1200;
+		/delete-node/ opp-625000000-1250;
+		/delete-node/ opp-667000000-1200;
+		/delete-node/ opp-750000000-1300;
+		/delete-node/ opp-800000000-1300;
+		/delete-node/ opp-900000000-1350;
+	};
+
+	brcm_wifi_pwrseq: pwrseq-wifi {
+		compatible = "mmc-pwrseq-simple";
+
+		clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
+		clock-names = "ext_clock";
+
+		reset-gpios = <&gpio TEGRA_GPIO(D, 3) GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <300>;
+		power-off-delay-us = <300>;
+	};
+
 	sound {
 		compatible = "pegatron,tegra-audio-wm8903-chagall",
 			     "nvidia,tegra-audio-wm8903";
@@ -2842,20 +2874,3 @@
 		};
 	};
 };
-
-&emc_icc_dvfs_opp_table {
-	/delete-node/ opp-625000000-1200;
-	/delete-node/ opp-625000000-1250;
-	/delete-node/ opp-667000000-1200;
-	/delete-node/ opp-750000000-1300;
-	/delete-node/ opp-800000000-1300;
-	/delete-node/ opp-900000000-1350;
-};
-
-&emc_bw_dfs_opp_table {
-	/delete-node/ opp-625000000;
-	/delete-node/ opp-667000000;
-	/delete-node/ opp-750000000;
-	/delete-node/ opp-800000000;
-	/delete-node/ opp-900000000;
-};
diff --git a/arch/arm/boot/dts/tegra30-peripherals-opp.dtsi b/arch/arm/boot/dts/nvidia/tegra30-peripherals-opp.dtsi
index d100a1a8b705..a2d557155114 100644
--- a/arch/arm/boot/dts/tegra30-peripherals-opp.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra30-peripherals-opp.dtsi
@@ -210,6 +210,20 @@
 			opp-suspend;
 		};
 
+		opp-266500000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <266500000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-266500000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <266500000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
+		};
+
 		opp-333500000-1000 {
 			opp-microvolt = <1000000 1000000 1350000>;
 			opp-hz = /bits/ 64 <333500000>;
@@ -424,6 +438,12 @@
 			opp-suspend;
 		};
 
+		opp-266500000 {
+			opp-hz = /bits/ 64 <266500000>;
+			opp-supported-hw = <0x000F>;
+			opp-peak-kBps = <2132000>;
+		};
+
 		opp-333500000 {
 			opp-hz = /bits/ 64 <333500000>;
 			opp-supported-hw = <0x000F>;
diff --git a/arch/arm/boot/dts/tegra30.dtsi b/arch/arm/boot/dts/nvidia/tegra30.dtsi
index 9dab8d2c158a..2a4d93db8134 100644
--- a/arch/arm/boot/dts/tegra30.dtsi
+++ b/arch/arm/boot/dts/nvidia/tegra30.dtsi
@@ -397,13 +397,6 @@
 		#clock-cells = <1>;
 		#reset-cells = <1>;
 
-		sclk {
-			compatible = "nvidia,tegra30-sclk";
-			clocks = <&tegra_car TEGRA30_CLK_SCLK>;
-			power-domains = <&pd_core>;
-			operating-points-v2 = <&sclk_dvfs_opp_table>;
-		};
-
 		pll-c {
 			compatible = "nvidia,tegra30-pllc";
 			clocks = <&tegra_car TEGRA30_CLK_PLL_C>;
@@ -424,6 +417,13 @@
 			power-domains = <&pd_core>;
 			operating-points-v2 = <&pll_m_dvfs_opp_table>;
 		};
+
+		sclk {
+			compatible = "nvidia,tegra30-sclk";
+			clocks = <&tegra_car TEGRA30_CLK_SCLK>;
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&sclk_dvfs_opp_table>;
+		};
 	};
 
 	flow-controller@60007000 {
@@ -431,7 +431,7 @@
 		reg = <0x60007000 0x1000>;
 	};
 
-	apbdma: dma@6000a000 {
+	apbdma: dma-controller@6000a000 {
 		compatible = "nvidia,tegra30-apbdma", "nvidia,tegra20-apbdma";
 		reg = <0x6000a000 0x1400>;
 		interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
@@ -563,7 +563,6 @@
 		interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA30_CLK_UARTA>;
 		resets = <&tegra_car 6>;
-		reset-names = "serial";
 		dmas = <&apbdma 8>, <&apbdma 8>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -576,7 +575,6 @@
 		interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA30_CLK_UARTB>;
 		resets = <&tegra_car 7>;
-		reset-names = "serial";
 		dmas = <&apbdma 9>, <&apbdma 9>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -589,7 +587,6 @@
 		interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA30_CLK_UARTC>;
 		resets = <&tegra_car 55>;
-		reset-names = "serial";
 		dmas = <&apbdma 10>, <&apbdma 10>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -602,7 +599,6 @@
 		interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA30_CLK_UARTD>;
 		resets = <&tegra_car 65>;
-		reset-names = "serial";
 		dmas = <&apbdma 19>, <&apbdma 19>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -615,7 +611,6 @@
 		interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA30_CLK_UARTE>;
 		resets = <&tegra_car 66>;
-		reset-names = "serial";
 		dmas = <&apbdma 20>, <&apbdma 20>;
 		dma-names = "rx", "tx";
 		status = "disabled";
@@ -648,13 +643,6 @@
 		status = "disabled";
 	};
 
-	rtc@7000e000 {
-		compatible = "nvidia,tegra30-rtc", "nvidia,tegra20-rtc";
-		reg = <0x7000e000 0x100>;
-		interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&tegra_car TEGRA30_CLK_RTC>;
-	};
-
 	i2c@7000c000 {
 		compatible = "nvidia,tegra30-i2c", "nvidia,tegra20-i2c";
 		reg = <0x7000c000 0x100>;
@@ -831,6 +819,13 @@
 		status = "disabled";
 	};
 
+	rtc@7000e000 {
+		compatible = "nvidia,tegra30-rtc", "nvidia,tegra20-rtc";
+		reg = <0x7000e000 0x100>;
+		interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&tegra_car TEGRA30_CLK_RTC>;
+	};
+
 	kbc@7000e200 {
 		compatible = "nvidia,tegra30-kbc", "nvidia,tegra20-kbc";
 		reg = <0x7000e200 0x100>;
@@ -854,6 +849,28 @@
 		};
 
 		powergates {
+			pd_heg: heg {
+				clocks = <&tegra_car TEGRA30_CLK_GR2D>,
+					 <&tegra_car TEGRA30_CLK_EPP>,
+					 <&tegra_car TEGRA30_CLK_HOST1X>;
+				resets = <&mc TEGRA30_MC_RESET_2D>,
+					 <&mc TEGRA30_MC_RESET_EPP>,
+					 <&mc TEGRA30_MC_RESET_HC>,
+					 <&tegra_car TEGRA30_CLK_GR2D>,
+					 <&tegra_car TEGRA30_CLK_EPP>,
+					 <&tegra_car TEGRA30_CLK_HOST1X>;
+				power-domains = <&pd_core>;
+				#power-domain-cells = <0>;
+			};
+
+			pd_mpe: mpe {
+				clocks = <&tegra_car TEGRA30_CLK_MPE>;
+				resets = <&mc TEGRA30_MC_RESET_MPE>,
+					 <&tegra_car TEGRA30_CLK_MPE>;
+				power-domains = <&pd_core>;
+				#power-domain-cells = <0>;
+			};
+
 			pd_3d0: td {
 				clocks = <&tegra_car TEGRA30_CLK_GR3D>;
 				resets = <&mc TEGRA30_MC_RESET_3D>,
@@ -870,6 +887,14 @@
 				#power-domain-cells = <0>;
 			};
 
+			pd_vde: vdec {
+				clocks = <&tegra_car TEGRA30_CLK_VDE>;
+				resets = <&mc TEGRA30_MC_RESET_VDE>,
+					 <&tegra_car TEGRA30_CLK_VDE>;
+				power-domains = <&pd_core>;
+				#power-domain-cells = <0>;
+			};
+
 			pd_venc: venc {
 				clocks = <&tegra_car TEGRA30_CLK_ISP>,
 					 <&tegra_car TEGRA30_CLK_VI>,
@@ -882,36 +907,6 @@
 				power-domains = <&pd_core>;
 				#power-domain-cells = <0>;
 			};
-
-			pd_vde: vdec {
-				clocks = <&tegra_car TEGRA30_CLK_VDE>;
-				resets = <&mc TEGRA30_MC_RESET_VDE>,
-					 <&tegra_car TEGRA30_CLK_VDE>;
-				power-domains = <&pd_core>;
-				#power-domain-cells = <0>;
-			};
-
-			pd_mpe: mpe {
-				clocks = <&tegra_car TEGRA30_CLK_MPE>;
-				resets = <&mc TEGRA30_MC_RESET_MPE>,
-					 <&tegra_car TEGRA30_CLK_MPE>;
-				power-domains = <&pd_core>;
-				#power-domain-cells = <0>;
-			};
-
-			pd_heg: heg {
-				clocks = <&tegra_car TEGRA30_CLK_GR2D>,
-					 <&tegra_car TEGRA30_CLK_EPP>,
-					 <&tegra_car TEGRA30_CLK_HOST1X>;
-				resets = <&mc TEGRA30_MC_RESET_2D>,
-					 <&mc TEGRA30_MC_RESET_EPP>,
-					 <&mc TEGRA30_MC_RESET_HC>,
-					 <&tegra_car TEGRA30_CLK_GR2D>,
-					 <&tegra_car TEGRA30_CLK_EPP>,
-					 <&tegra_car TEGRA30_CLK_HOST1X>;
-				power-domains = <&pd_core>;
-				#power-domain-cells = <0>;
-			};
 		};
 	};
 
@@ -1283,10 +1278,7 @@
 			     <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-affinity = <&{/cpus/cpu@0}>,
-				     <&{/cpus/cpu@1}>,
-				     <&{/cpus/cpu@2}>,
-				     <&{/cpus/cpu@3}>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
 	};
 
 	thermal-zones {
diff --git a/arch/arm/boot/dts/nxp/Makefile b/arch/arm/boot/dts/nxp/Makefile
new file mode 100644
index 000000000000..db44e7a0a198
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0
+subdir-y += imx
+subdir-y += lpc
+subdir-y += ls
+subdir-y += mxs
+subdir-y += vf
diff --git a/arch/arm/boot/dts/nxp/imx/Makefile b/arch/arm/boot/dts/nxp/imx/Makefile
new file mode 100644
index 000000000000..de4142e8f3ce
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/Makefile
@@ -0,0 +1,419 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_SOC_IMX1) += \
+	imx1-ads.dtb \
+	imx1-apf9328.dtb
+dtb-$(CONFIG_SOC_IMX25) += \
+	imx25-eukrea-mbimxsd25-baseboard.dtb \
+	imx25-eukrea-mbimxsd25-baseboard-cmo-qvga.dtb \
+	imx25-eukrea-mbimxsd25-baseboard-dvi-svga.dtb \
+	imx25-eukrea-mbimxsd25-baseboard-dvi-vga.dtb \
+	imx25-karo-tx25.dtb \
+	imx25-pdk.dtb
+dtb-$(CONFIG_SOC_IMX27) += \
+	imx27-apf27.dtb \
+	imx27-apf27dev.dtb \
+	imx27-eukrea-mbimxsd27-baseboard.dtb \
+	imx27-pdk.dtb \
+	imx27-phytec-phycore-rdk.dtb \
+	imx27-phytec-phycard-s-rdk.dtb
+dtb-$(CONFIG_SOC_IMX31) += \
+	imx31-bug.dtb \
+	imx31-lite.dtb
+dtb-$(CONFIG_SOC_IMX35) += \
+	imx35-eukrea-mbimxsd35-baseboard.dtb \
+	imx35-pdk.dtb
+dtb-$(CONFIG_SOC_IMX50) += \
+	imx50-evk.dtb \
+	imx50-kobo-aura.dtb
+dtb-$(CONFIG_SOC_IMX51) += \
+	imx51-apf51.dtb \
+	imx51-apf51dev.dtb \
+	imx51-babbage.dtb \
+	imx51-digi-connectcore-jsk.dtb \
+	imx51-eukrea-mbimxsd51-baseboard.dtb \
+	imx51-ts4800.dtb \
+	imx51-zii-rdu1.dtb \
+	imx51-zii-scu2-mezz.dtb \
+	imx51-zii-scu3-esb.dtb
+dtb-$(CONFIG_SOC_IMX53) += \
+	imx53-ard.dtb \
+	imx53-cx9020.dtb \
+	imx53-kp-ddc.dtb \
+	imx53-kp-hsc.dtb \
+	imx53-m53evk.dtb \
+	imx53-m53menlo.dtb \
+	imx53-mba53.dtb \
+	imx53-ppd.dtb \
+	imx53-qsb.dtb \
+	imx53-qsb-hdmi.dtb \
+	imx53-qsrb.dtb \
+	imx53-qsrb-hdmi.dtb \
+	imx53-sk-imx53.dtb \
+	imx53-sk-imx53-atm0700d4-lvds.dtb \
+	imx53-sk-imx53-atm0700d4-rgb.dtb \
+	imx53-smd.dtb \
+	imx53-tx53-x03x.dtb \
+	imx53-tx53-x13x.dtb \
+	imx53-usbarmory.dtb \
+	imx53-voipac-bsb.dtb
+imx53-qsb-hdmi-dtbs := imx53-qsb.dtb imx53-qsb-hdmi.dtbo
+imx53-qsrb-hdmi-dtbs := imx53-qsrb.dtb imx53-qsb-hdmi.dtbo
+dtb-$(CONFIG_SOC_IMX6Q) += \
+	imx6dl-alti6p.dtb \
+	imx6dl-apf6dev.dtb \
+	imx6dl-aristainetos_4.dtb \
+	imx6dl-aristainetos_7.dtb \
+	imx6dl-aristainetos2_4.dtb \
+	imx6dl-aristainetos2_7.dtb \
+	imx6dl-colibri-aster.dtb \
+	imx6dl-colibri-eval-v3.dtb \
+	imx6dl-colibri-iris.dtb \
+	imx6dl-colibri-iris-v2.dtb \
+	imx6dl-colibri-v1.2-aster.dtb \
+	imx6dl-colibri-v1.2-eval-v3.dtb \
+	imx6dl-colibri-v1.2-iris.dtb \
+	imx6dl-colibri-v1.2-iris-v2.dtb \
+	imx6dl-cubox-i.dtb \
+	imx6dl-cubox-i-emmc-som-v15.dtb \
+	imx6dl-cubox-i-som-v15.dtb \
+	imx6dl-dfi-fs700-m60.dtb \
+	imx6dl-dhcom-pdk2.dtb \
+	imx6dl-dhcom-picoitx.dtb \
+	imx6dl-eckelmann-ci4x10.dtb \
+	imx6dl-emcon-avari.dtb \
+	imx6dl-gw51xx.dtb \
+	imx6dl-gw52xx.dtb \
+	imx6dl-gw53xx.dtb \
+	imx6dl-gw54xx.dtb \
+	imx6dl-gw551x.dtb \
+	imx6dl-gw552x.dtb \
+	imx6dl-gw553x.dtb \
+	imx6dl-gw560x.dtb \
+	imx6dl-gw5903.dtb \
+	imx6dl-gw5904.dtb \
+	imx6dl-gw5907.dtb \
+	imx6dl-gw5910.dtb \
+	imx6dl-gw5912.dtb \
+	imx6dl-gw5913.dtb \
+	imx6dl-hummingboard.dtb \
+	imx6dl-hummingboard-emmc-som-v15.dtb \
+	imx6dl-hummingboard-som-v15.dtb \
+	imx6dl-hummingboard2.dtb \
+	imx6dl-hummingboard2-emmc-som-v15.dtb \
+	imx6dl-hummingboard2-som-v15.dtb \
+	imx6dl-icore.dtb \
+	imx6dl-icore-mipi.dtb \
+	imx6dl-icore-rqs.dtb \
+	imx6dl-kontron-samx6i-ads2.dtb \
+	imx6dl-lanmcu.dtb \
+	imx6dl-mamoj.dtb \
+	imx6dl-mba6a.dtb \
+	imx6dl-mba6b.dtb \
+	imx6dl-nit6xlite.dtb \
+	imx6dl-nitrogen6x.dtb \
+	imx6dl-phytec-mira-rdk-nand.dtb \
+	imx6dl-phytec-pbab01.dtb \
+	imx6dl-pico-dwarf.dtb \
+	imx6dl-pico-hobbit.dtb \
+	imx6dl-pico-nymph.dtb \
+	imx6dl-pico-pi.dtb \
+	imx6dl-plybas.dtb \
+	imx6dl-plym2m.dtb \
+	imx6dl-prtmvt.dtb \
+	imx6dl-prtrvt.dtb \
+	imx6dl-prtvt7.dtb \
+	imx6dl-rex-basic.dtb \
+	imx6dl-riotboard.dtb \
+	imx6dl-sabreauto.dtb \
+	imx6dl-sabrelite.dtb \
+	imx6dl-sabresd.dtb \
+	imx6dl-savageboard.dtb \
+	imx6dl-sielaff.dtb \
+	imx6dl-skov-revc-lt2.dtb \
+	imx6dl-skov-revc-lt6.dtb \
+	imx6dl-solidsense.dtb \
+	imx6dl-ts4900.dtb \
+	imx6dl-ts7970.dtb \
+	imx6dl-tx6dl-comtft.dtb \
+	imx6dl-tx6s-8034.dtb \
+	imx6dl-tx6s-8034-mb7.dtb \
+	imx6dl-tx6s-8035.dtb \
+	imx6dl-tx6s-8035-mb7.dtb \
+	imx6dl-tx6u-801x.dtb \
+	imx6dl-tx6u-80xx-mb7.dtb \
+	imx6dl-tx6u-8033.dtb \
+	imx6dl-tx6u-8033-mb7.dtb \
+	imx6dl-tx6u-811x.dtb \
+	imx6dl-tx6u-81xx-mb7.dtb \
+	imx6dl-udoo.dtb \
+	imx6dl-victgo.dtb \
+	imx6dl-vicut1.dtb \
+	imx6dl-wandboard.dtb \
+	imx6dl-wandboard-revb1.dtb \
+	imx6dl-wandboard-revd1.dtb \
+	imx6dl-yapp4-draco.dtb \
+	imx6dl-yapp4-hydra.dtb \
+	imx6dl-yapp4-lynx.dtb \
+	imx6dl-yapp4-orion.dtb \
+	imx6dl-yapp4-phoenix.dtb \
+	imx6dl-yapp4-ursa.dtb \
+	imx6q-apalis-eval.dtb \
+	imx6q-apalis-eval-v1.2.dtb \
+	imx6q-apalis-ixora.dtb \
+	imx6q-apalis-ixora-v1.1.dtb \
+	imx6q-apalis-ixora-v1.2.dtb \
+	imx6q-apalis-v1.2-eval.dtb \
+	imx6q-apalis-v1.2-eval-v1.2.dtb \
+	imx6q-apalis-v1.2-ixora.dtb \
+	imx6q-apalis-v1.2-ixora-v1.1.dtb \
+	imx6q-apalis-v1.2-ixora-v1.2.dtb \
+	imx6q-apf6dev.dtb \
+	imx6q-arm2.dtb \
+	imx6q-b450v3.dtb \
+	imx6q-b650v3.dtb \
+	imx6q-b850v3.dtb \
+	imx6q-bosch-acc.dtb \
+	imx6q-cm-fx6.dtb \
+	imx6q-cubox-i.dtb \
+	imx6q-cubox-i-emmc-som-v15.dtb \
+	imx6q-cubox-i-som-v15.dtb \
+	imx6q-dfi-fs700-m60.dtb \
+	imx6q-dhcom-pdk2.dtb \
+	imx6q-display5-tianma-tm070-1280x768.dtb \
+	imx6q-dmo-edmqmx6.dtb \
+	imx6q-dms-ba16.dtb \
+	imx6q-ds.dtb \
+	imx6q-emcon-avari.dtb \
+	imx6q-evi.dtb \
+	imx6dl-b105pv2.dtb \
+	imx6dl-b105v2.dtb \
+	imx6dl-b125v2.dtb \
+	imx6dl-b125pv2.dtb \
+	imx6dl-b155v2.dtb \
+	imx6q-gk802.dtb \
+	imx6q-gw51xx.dtb \
+	imx6q-gw52xx.dtb \
+	imx6q-gw53xx.dtb \
+	imx6q-gw5400-a.dtb \
+	imx6q-gw54xx.dtb \
+	imx6q-gw551x.dtb \
+	imx6q-gw552x.dtb \
+	imx6q-gw553x.dtb \
+	imx6q-gw560x.dtb \
+	imx6q-gw5903.dtb \
+	imx6q-gw5904.dtb \
+	imx6q-gw5907.dtb \
+	imx6q-gw5910.dtb \
+	imx6q-gw5912.dtb \
+	imx6q-gw5913.dtb \
+	imx6q-h100.dtb \
+	imx6q-hummingboard.dtb \
+	imx6q-hummingboard-emmc-som-v15.dtb \
+	imx6q-hummingboard-som-v15.dtb \
+	imx6q-hummingboard2.dtb \
+	imx6q-hummingboard2-emmc-som-v15.dtb \
+	imx6q-hummingboard2-som-v15.dtb \
+	imx6q-icore.dtb \
+	imx6q-icore-mipi.dtb \
+	imx6q-icore-ofcap10.dtb \
+	imx6q-icore-ofcap12.dtb \
+	imx6q-icore-rqs.dtb \
+	imx6q-kontron-samx6i-ads2.dtb \
+	imx6q-kp-tpc.dtb \
+	imx6q-logicpd.dtb \
+	imx6q-lxr.dtb \
+	imx6q-marsboard.dtb \
+	imx6q-mba6a.dtb \
+	imx6q-mba6b.dtb \
+	imx6q-mccmon6.dtb \
+	imx6q-nitrogen6x.dtb \
+	imx6q-nitrogen6_max.dtb \
+	imx6q-nitrogen6_som2.dtb \
+	imx6q-novena.dtb \
+	imx6q-phytec-mira-rdk-emmc.dtb \
+	imx6q-phytec-mira-rdk-nand.dtb \
+	imx6q-phytec-pbab01.dtb \
+	imx6q-pico-dwarf.dtb \
+	imx6q-pico-hobbit.dtb \
+	imx6q-pico-nymph.dtb \
+	imx6q-pico-pi.dtb \
+	imx6q-pistachio.dtb \
+	imx6q-prti6q.dtb \
+	imx6q-prtwd2.dtb \
+	imx6q-rex-pro.dtb \
+	imx6q-sabreauto.dtb \
+	imx6q-sabrelite.dtb \
+	imx6q-sabresd.dtb \
+	imx6q-savageboard.dtb \
+	imx6q-sbc6x.dtb \
+	imx6q-skov-revc-lt2.dtb \
+	imx6q-skov-revc-lt6.dtb \
+	imx6q-skov-reve-mi1010ait-1cp1.dtb \
+	imx6q-solidsense.dtb \
+	imx6q-tbs2910.dtb \
+	imx6q-ts4900.dtb \
+	imx6q-ts7970.dtb \
+	imx6q-tx6q-1010.dtb \
+	imx6q-tx6q-1010-comtft.dtb \
+	imx6q-tx6q-1020.dtb \
+	imx6q-tx6q-1020-comtft.dtb \
+	imx6q-tx6q-1036.dtb \
+	imx6q-tx6q-1036-mb7.dtb \
+	imx6q-tx6q-10x0-mb7.dtb \
+	imx6q-tx6q-1110.dtb \
+	imx6q-tx6q-11x0-mb7.dtb \
+	imx6q-udoo.dtb \
+	imx6q-utilite-pro.dtb \
+	imx6q-var-dt6customboard.dtb \
+	imx6q-var-mx6customboard.dtb \
+	imx6q-vicut1.dtb \
+	imx6q-wandboard.dtb \
+	imx6q-wandboard-revb1.dtb \
+	imx6q-wandboard-revd1.dtb \
+	imx6q-yapp4-crux.dtb \
+	imx6q-yapp4-pegasus.dtb \
+	imx6q-zii-rdu2.dtb \
+	imx6qp-mba6b.dtb \
+	imx6qp-nitrogen6_max.dtb \
+	imx6qp-nitrogen6_som2.dtb \
+	imx6qp-phytec-mira-rdk-nand.dtb \
+	imx6qp-prtwd3.dtb \
+	imx6qp-sabreauto.dtb \
+	imx6qp-sabresd.dtb \
+	imx6qp-tx6qp-8037.dtb \
+	imx6qp-tx6qp-8037-mb7.dtb \
+	imx6qp-tx6qp-8137.dtb \
+	imx6qp-tx6qp-8137-mb7.dtb \
+	imx6qp-vicutp.dtb \
+	imx6qp-wandboard-revd1.dtb \
+	imx6qp-yapp4-crux-plus.dtb \
+	imx6qp-yapp4-pegasus-plus.dtb \
+	imx6qp-zii-rdu2.dtb \
+	imx6s-dhcom-drc02.dtb
+dtb-$(CONFIG_SOC_IMX6SL) += \
+	imx6sl-evk.dtb \
+	imx6sl-kobo-aura2.dtb \
+	imx6sl-tolino-shine2hd.dtb \
+	imx6sl-tolino-shine3.dtb \
+	imx6sl-tolino-vision.dtb \
+	imx6sl-tolino-vision5.dtb \
+	imx6sl-warp.dtb
+dtb-$(CONFIG_SOC_IMX6SLL) += \
+	imx6sll-evk.dtb \
+	imx6sll-kobo-clarahd.dtb \
+	imx6sll-kobo-clara2e-a.dtb \
+	imx6sll-kobo-clara2e-b.dtb \
+	imx6sll-kobo-librah2o.dtb
+dtb-$(CONFIG_SOC_IMX6SX) += \
+	imx6sx-nitrogen6sx.dtb \
+	imx6sx-sabreauto.dtb \
+	imx6sx-sdb-reva.dtb \
+	imx6sx-sdb-sai.dtb \
+	imx6sx-sdb.dtb \
+	imx6sx-sdb-mqs.dtb \
+	imx6sx-softing-vining-2000.dtb \
+	imx6sx-udoo-neo-basic.dtb \
+	imx6sx-udoo-neo-extended.dtb \
+	imx6sx-udoo-neo-full.dtb
+dtb-$(CONFIG_SOC_IMX6UL) += \
+	imx6ul-14x14-evk.dtb \
+	imx6ul-ccimx6ulsbcexpress.dtb \
+	imx6ul-ccimx6ulsbcpro.dtb \
+	imx6ul-geam.dtb \
+	imx6ul-isiot-emmc.dtb \
+	imx6ul-isiot-nand.dtb \
+	imx6ul-kontron-bl.dtb \
+	imx6ul-kontron-bl-43.dtb \
+	imx6ul-liteboard.dtb \
+	imx6ul-tqma6ul1-mba6ulx.dtb \
+	imx6ul-tqma6ul2-mba6ulx.dtb \
+	imx6ul-tqma6ul2l-mba6ulx.dtb \
+	imx6ul-opos6uldev.dtb \
+	imx6ul-pico-dwarf.dtb \
+	imx6ul-pico-hobbit.dtb \
+	imx6ul-pico-pi.dtb \
+	imx6ul-phytec-segin-ff-rdk-emmc.dtb \
+	imx6ul-phytec-segin-ff-rdk-nand.dtb \
+	imx6ul-prti6g.dtb \
+	imx6ul-tx6ul-0010.dtb \
+	imx6ul-tx6ul-0011.dtb \
+	imx6ul-tx6ul-mainboard.dtb \
+	imx6ul-var-som-concerto.dtb \
+	imx6ull-14x14-evk.dtb \
+	imx6ull-colibri-aster.dtb \
+	imx6ull-colibri-emmc-aster.dtb \
+	imx6ull-colibri-emmc-eval-v3.dtb \
+	imx6ull-colibri-emmc-iris.dtb \
+	imx6ull-colibri-emmc-iris-v2.dtb \
+	imx6ull-colibri-eval-v3.dtb \
+	imx6ull-colibri-iris.dtb \
+	imx6ull-colibri-iris-v2.dtb \
+	imx6ull-colibri-wifi-aster.dtb \
+	imx6ull-colibri-wifi-eval-v3.dtb \
+	imx6ull-colibri-wifi-iris.dtb \
+	imx6ull-colibri-wifi-iris-v2.dtb \
+	imx6ull-dhcom-drc02.dtb \
+	imx6ull-dhcom-pdk2.dtb \
+	imx6ull-dhcom-picoitx.dtb \
+	imx6ull-dhcor-maveo-box.dtb \
+	imx6ull-engicam-microgea-bmm.dtb \
+	imx6ull-engicam-microgea-gtw.dtb \
+	imx6ull-engicam-microgea-rmm.dtb \
+	imx6ull-jozacp.dtb \
+	imx6ull-kontron-bl.dtb \
+	imx6ull-myir-mys-6ulx-eval.dtb \
+	imx6ull-opos6uldev.dtb \
+	imx6ull-phytec-segin-ff-rdk-nand.dtb \
+	imx6ull-phytec-segin-ff-rdk-emmc.dtb \
+	imx6ull-phytec-segin-lc-rdk-nand.dtb \
+	imx6ull-phytec-tauri-emmc.dtb \
+	imx6ull-phytec-tauri-nand.dtb \
+	imx6ull-seeed-npi-dev-board-emmc.dtb \
+	imx6ull-seeed-npi-dev-board-nand.dtb \
+	imx6ull-tarragon-master.dtb \
+	imx6ull-tarragon-micro.dtb \
+	imx6ull-tarragon-slave.dtb \
+	imx6ull-tarragon-slavext.dtb \
+	imx6ull-tqma6ull2-mba6ulx.dtb \
+	imx6ull-tqma6ull2l-mba6ulx.dtb \
+	imx6ull-uti260b.dtb \
+	imx6ulz-14x14-evk.dtb \
+	imx6ulz-bsh-smm-m2.dtb
+dtb-$(CONFIG_SOC_IMX7D) += \
+	imx7d-cl-som-imx7.dtb \
+	imx7d-colibri-aster.dtb \
+	imx7d-colibri-emmc-aster.dtb \
+	imx7d-colibri-emmc-iris.dtb \
+	imx7d-colibri-emmc-iris-v2.dtb \
+	imx7d-colibri-emmc-eval-v3.dtb \
+	imx7d-colibri-eval-v3.dtb \
+	imx7d-colibri-iris.dtb \
+	imx7d-colibri-iris-v2.dtb \
+	imx7d-flex-concentrator.dtb \
+	imx7d-flex-concentrator-mfg.dtb \
+	imx7d-mba7.dtb \
+	imx7d-meerkat96.dtb \
+	imx7d-nitrogen7.dtb \
+	imx7d-pico-dwarf.dtb \
+	imx7d-pico-hobbit.dtb \
+	imx7d-pico-nymph.dtb \
+	imx7d-pico-pi.dtb \
+	imx7d-remarkable2.dtb \
+	imx7d-sbc-imx7.dtb \
+	imx7d-sdb.dtb \
+	imx7d-sdb-reva.dtb \
+	imx7d-sdb-sht11.dtb \
+	imx7d-smegw01.dtb \
+	imx7d-zii-rmu2.dtb \
+	imx7d-zii-rpu2.dtb \
+	imx7s-colibri-aster.dtb \
+	imx7s-colibri-eval-v3.dtb \
+	imx7s-colibri-iris.dtb \
+	imx7s-colibri-iris-v2.dtb \
+	imx7s-mba7.dtb \
+	imx7s-warp.dtb
+dtb-$(CONFIG_SOC_IMX7ULP) += \
+	imx7ulp-com.dtb \
+	imx7ulp-evk.dtb
+dtb-$(CONFIG_SOC_IMXRT) += \
+	imxrt1050-evk.dtb
diff --git a/arch/arm/boot/dts/e60k02.dtsi b/arch/arm/boot/dts/nxp/imx/e60k02.dtsi
index 1a49f15f2df2..0029c12f16c8 100644
--- a/arch/arm/boot/dts/e60k02.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/e60k02.dtsi
@@ -14,6 +14,10 @@
 #include <dt-bindings/input/input.h>
 
 / {
+	aliases {
+		mmc0 = &usdhc2;
+		mmc1 = &usdhc3;
+	};
 
 	chosen {
 		stdout-path = &uart1;
@@ -22,14 +26,14 @@
 	gpio_keys: gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			wakeup-source;
 		};
 
-		cover {
+		key-cover {
 			label = "Cover";
 			gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
 			linux,code = <SW_LID>;
@@ -104,7 +108,16 @@
 	clock-frequency = <100000>;
 	status = "okay";
 
-	/* TODO: CYTTSP5 touch controller at 0x24 */
+	touchscreen@24 {
+		compatible = "cypress,tt21000";
+		reg = <0x24>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_cyttsp5_gpio>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+		vdd-supply = <&ldo5_reg>;
+	};
 
 	/* TODO: TPS65185 PMIC for E Ink at 0x68 */
 
@@ -118,7 +131,7 @@
 		compatible = "ricoh,rc5t619";
 		reg = <0x32>;
 		interrupt-parent = <&gpio5>;
-		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
 		system-power-controller;
 
 		regulators {
@@ -302,6 +315,7 @@
 
 &usbotg1 {
 	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
 	disable-over-current;
 	srp-disable;
 	hnp-disable;
diff --git a/arch/arm/boot/dts/e70k02.dtsi b/arch/arm/boot/dts/nxp/imx/e70k02.dtsi
index 156de653f2cd..dcc3c9d488a8 100644
--- a/arch/arm/boot/dts/e70k02.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/e70k02.dtsi
@@ -26,14 +26,14 @@
 	gpio_keys: gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio4 25 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			wakeup-source;
 		};
 
-		cover {
+		key-cover {
 			label = "Cover";
 			gpios = <&gpio4 23 GPIO_ACTIVE_LOW>;
 			linux,code = <SW_LID>;
@@ -41,13 +41,13 @@
 			wakeup-source;
 		};
 
-		pageup {
+		key-pageup {
 			label = "PageUp";
 			gpios = <&gpio4 0 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_PAGEUP>;
 		};
 
-		pagedown {
+		key-pagedown {
 			label = "PageDown";
 			gpios = <&gpio4 2 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_PAGEDOWN>;
@@ -122,7 +122,16 @@
 	clock-frequency = <100000>;
 	status = "okay";
 
-	/* TODO: CYTTSP5 touch controller at 0x24 */
+	touchscreen@24 {
+		compatible = "cypress,tt21000";
+		reg = <0x24>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_cyttsp5_gpio>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&gpio4 18 GPIO_ACTIVE_LOW>;
+		vdd-supply = <&ldo5_reg>;
+	};
 
 	/* TODO: SY7636 PMIC for E Ink at 0x62 */
 
@@ -136,7 +145,7 @@
 		compatible = "ricoh,rc5t619";
 		reg = <0x32>;
 		interrupt-parent = <&gpio4>;
-		interrupts = <19 IRQ_TYPE_EDGE_FALLING>;
+		interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
 		system-power-controller;
 
 		regulators {
@@ -312,6 +321,7 @@
 
 &usbotg1 {
 	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
 	disable-over-current;
 	srp-disable;
 	hnp-disable;
diff --git a/arch/arm/boot/dts/imx1-ads.dts b/arch/arm/boot/dts/nxp/imx/imx1-ads.dts
index 5833fb6f15d8..2c817c4a4c68 100644
--- a/arch/arm/boot/dts/imx1-ads.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx1-ads.dts
@@ -65,7 +65,7 @@
 	pinctrl-0 = <&pinctrl_weim>;
 	status = "okay";
 
-	nor: nor@0,0 {
+	nor: flash@0,0 {
 		compatible = "cfi-flash";
 		reg = <0 0x00000000 0x02000000>;
 		bank-width = <4>;
diff --git a/arch/arm/boot/dts/imx1-apf9328.dts b/arch/arm/boot/dts/nxp/imx/imx1-apf9328.dts
index 77b21aa7a146..058e9435524f 100644
--- a/arch/arm/boot/dts/imx1-apf9328.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx1-apf9328.dts
@@ -45,7 +45,7 @@
 	pinctrl-0 = <&pinctrl_weim>;
 	status = "okay";
 
-	nor: nor@0,0 {
+	nor: flash@0,0 {
 		compatible = "cfi-flash";
 		reg = <0 0x00000000 0x02000000>;
 		bank-width = <2>;
@@ -54,14 +54,12 @@
 		#size-cells = <1>;
 	};
 
-	eth: eth@4,c00000 {
+	eth: ethernet@4,c00000 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_eth>;
 		compatible = "davicom,dm9000";
-		reg = <
-			4 0x00c00000 0x2
-			4 0x00c00002 0x2
-		>;
+		reg = <4 0x00c00000 0x2>,
+		      <4 0x00c00002 0x2>;
 		interrupt-parent = <&gpio2>;
 		interrupts = <14 IRQ_TYPE_LEVEL_LOW>;
 		fsl,weim-cs-timing = <0x0000c700 0x19190d01>;
diff --git a/arch/arm/boot/dts/imx1-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx1-pinfunc.h
index bd2e679cb26c..bd2e679cb26c 100644
--- a/arch/arm/boot/dts/imx1-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx1-pinfunc.h
diff --git a/arch/arm/boot/dts/imx1.dtsi b/arch/arm/boot/dts/nxp/imx/imx1.dtsi
index e312f1e74e2f..a1a89ccacf05 100644
--- a/arch/arm/boot/dts/imx1.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx1.dtsi
@@ -68,7 +68,7 @@
 		interrupt-parent = <&aitc>;
 		ranges;
 
-		aipi@200000 {
+		bus@200000 {
 			compatible = "fsl,aipi-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -134,7 +134,7 @@
 				clock-names = "ipg", "per";
 			};
 
-			dma: dma@209000 {
+			dma: dma-controller@209000 {
 				compatible = "fsl,imx1-dma";
 				reg = <0x00209000 0x1000>;
 				interrupts = <61 60>;
@@ -155,7 +155,7 @@
 			};
 		};
 
-		aipi@210000 {
+		bus@210000 {
 			compatible = "fsl,aipi-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -251,7 +251,7 @@
 			};
 		};
 
-		weim: weim@220000 {
+		weim: memory-controller@220000 {
 			#address-cells = <2>;
 			#size-cells = <1>;
 			compatible = "fsl,imx1-weim";
@@ -268,9 +268,12 @@
 			status = "disabled";
 		};
 
-		esram: esram@300000 {
+		esram: sram@300000 {
 			compatible = "mmio-sram";
 			reg = <0x00300000 0x20000>;
+			ranges = <0 0x00300000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/imx25-eukrea-cpuimx25.dtsi b/arch/arm/boot/dts/nxp/imx/imx25-eukrea-cpuimx25.dtsi
index 0703f62d10d1..93a6e4e680b4 100644
--- a/arch/arm/boot/dts/imx25-eukrea-cpuimx25.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx25-eukrea-cpuimx25.dtsi
@@ -27,7 +27,7 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	pcf8563@51 {
+	rtc@51 {
 		compatible = "nxp,pcf8563";
 		reg = <0x51>;
 	};
diff --git a/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard-cmo-qvga.dts b/arch/arm/boot/dts/nxp/imx/imx25-eukrea-mbimxsd25-baseboard-cmo-qvga.dts
index 7d4301b22b90..6cddb2cc36fe 100644
--- a/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard-cmo-qvga.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx25-eukrea-mbimxsd25-baseboard-cmo-qvga.dts
@@ -16,7 +16,7 @@
 		bus-width = <18>;
 		display-timings {
 			native-mode = <&qvga_timings>;
-			qvga_timings: 320x240 {
+			qvga_timings: timing0 {
 				clock-frequency = <6500000>;
 				hactive = <320>;
 				vactive = <240>;
@@ -30,22 +30,15 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_lcd_3v3: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_reg_lcd_3v3>;
-			regulator-name = "lcd-3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	reg_lcd_3v3: regulator-0 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_lcd_3v3>;
+		regulator-name = "lcd-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard-dvi-svga.dts b/arch/arm/boot/dts/nxp/imx/imx25-eukrea-mbimxsd25-baseboard-dvi-svga.dts
index 80a7f96de4c6..64b2ffac463b 100644
--- a/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard-dvi-svga.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx25-eukrea-mbimxsd25-baseboard-dvi-svga.dts
@@ -16,7 +16,7 @@
 		bus-width = <18>;
 		display-timings {
 			native-mode = <&dvi_svga_timings>;
-			dvi_svga_timings: 800x600 {
+			dvi_svga_timings: timing0 {
 				clock-frequency = <40000000>;
 				hactive = <800>;
 				vactive = <600>;
diff --git a/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard-dvi-vga.dts b/arch/arm/boot/dts/nxp/imx/imx25-eukrea-mbimxsd25-baseboard-dvi-vga.dts
index 24027a1fb46d..fb074bfdaa8d 100644
--- a/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard-dvi-vga.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx25-eukrea-mbimxsd25-baseboard-dvi-vga.dts
@@ -16,7 +16,7 @@
 		bus-width = <18>;
 		display-timings {
 			native-mode = <&dvi_vga_timings>;
-			dvi_vga_timings: 640x480 {
+			dvi_vga_timings: timing0 {
 				clock-frequency = <31250000>;
 				hactive = <640>;
 				vactive = <480>;
diff --git a/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard.dts b/arch/arm/boot/dts/nxp/imx/imx25-eukrea-mbimxsd25-baseboard.dts
index 3f38c2e60a74..c7207ea437c4 100644
--- a/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx25-eukrea-mbimxsd25-baseboard.dts
@@ -13,12 +13,12 @@
 	model = "Eukrea MBIMXSD25";
 	compatible = "eukrea,mbimxsd25-baseboard", "eukrea,cpuimx25", "fsl,imx25";
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpiokeys>;
 
-		bp1 {
+		button {
 			label = "BP1";
 			gpios = <&gpio3 18 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_MISC>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx25-karo-tx25.dts b/arch/arm/boot/dts/nxp/imx/imx25-karo-tx25.dts
new file mode 100644
index 000000000000..458b94d3d4ed
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx25-karo-tx25.dts
@@ -0,0 +1,101 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 Sascha Hauer, Pengutronix
+ */
+
+/dts-v1/;
+#include "imx25.dtsi"
+
+/ {
+	model = "Ka-Ro TX25";
+	compatible = "karo,imx25-tx25", "fsl,imx25";
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	reg_fec_phy: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "fec-phy";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio4 9 0>;
+		enable-active-high;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x02000000 0x90000000 0x02000000>;
+	};
+};
+
+&iomuxc {
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX25_PAD_UART1_TXD__UART1_TXD 0x00000020
+			MX25_PAD_UART1_RXD__UART1_RXD 0x000000a0
+			MX25_PAD_UART1_CTS__UART1_CTS 0x00000060
+			MX25_PAD_UART1_RTS__UART1_RTS 0x000000e0
+		>;
+	};
+
+	pinctrl_fec: fecgrp {
+		fsl,pins = <
+			MX25_PAD_D11__GPIO_4_9		0x00000021 /* FEC PHY power on pin */
+			MX25_PAD_D13__GPIO_4_7		0x000000a1 /* FEC reset */
+			MX25_PAD_FEC_MDC__FEC_MDC	0x00000060
+			MX25_PAD_FEC_MDIO__FEC_MDIO	0x000001f0
+			MX25_PAD_FEC_TDATA0__FEC_TDATA0	0x00000060
+			MX25_PAD_FEC_TDATA1__FEC_TDATA1	0x00000060
+			MX25_PAD_FEC_TX_EN__FEC_TX_EN	0x00000060
+			MX25_PAD_FEC_RDATA0__FEC_RDATA0	0x000000c1
+			MX25_PAD_FEC_RDATA1__FEC_RDATA1	0x000000c0
+			MX25_PAD_FEC_RX_DV__FEC_RX_DV	0x000000c0
+			MX25_PAD_FEC_TX_CLK__FEC_TX_CLK	0x000000c0
+		>;
+	};
+
+	pinctrl_nfc: nfcgrp {
+		fsl,pins = <
+			MX25_PAD_NF_CE0__NF_CE0		0x00000001
+			MX25_PAD_NFWE_B__NFWE_B		0x80000000
+			MX25_PAD_NFRE_B__NFRE_B		0x80000000
+			MX25_PAD_NFALE__NFALE		0x80000000
+			MX25_PAD_NFCLE__NFCLE		0x80000000
+			MX25_PAD_NFWP_B__NFWP_B		0x80000000
+			MX25_PAD_NFRB__NFRB		0x000000e0
+			MX25_PAD_D7__D7			0x00000080
+			MX25_PAD_D6__D6			0x00000080
+			MX25_PAD_D5__D5			0x00000080
+			MX25_PAD_D4__D4			0x00000080
+			MX25_PAD_D3__D3			0x00000080
+			MX25_PAD_D2__D2			0x00000080
+			MX25_PAD_D1__D1			0x00000000
+			MX25_PAD_D0__D0			0x00000080
+		>;
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec>;
+	phy-reset-gpios = <&gpio3 7 GPIO_ACTIVE_LOW>;
+	phy-mode = "rmii";
+	phy-supply = <&reg_fec_phy>;
+	status = "okay";
+};
+
+&nfc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_nfc>;
+	nand-on-flash-bbt;
+	nand-ecc-mode = "hw";
+	nand-bus-width = <8>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx25-pdk.dts b/arch/arm/boot/dts/nxp/imx/imx25-pdk.dts
index fb66884d8a2f..dd176fb54e58 100644
--- a/arch/arm/boot/dts/imx25-pdk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx25-pdk.dts
@@ -16,45 +16,35 @@
 		reg = <0x80000000 0x4000000>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_fec_3v3: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "fec-3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio2 3 0>;
-			enable-active-high;
-		};
+	reg_fec_3v3: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "fec-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 3 0>;
+		enable-active-high;
+	};
 
-		reg_2p5v: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "2P5V";
-			regulator-min-microvolt = <2500000>;
-			regulator-max-microvolt = <2500000>;
-		};
+	reg_2p5v: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "2P5V";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+	};
 
-		reg_3p3v: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-		};
+	reg_3p3v: regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
 
-		reg_can_3v3: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "can-3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio4 6 0>;
-		};
+	reg_can_3v3: regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "can-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio4 6 0>;
 	};
 
 	sound {
@@ -78,7 +68,7 @@
 		bus-width = <18>;
 		display-timings {
 			native-mode = <&wvga_timings>;
-			wvga_timings: 640x480 {
+			wvga_timings: timing0 {
 				hactive = <640>;
 				vactive = <480>;
 				hback-porch = <45>;
@@ -132,6 +122,7 @@
 	codec: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks 129>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_3p3v>;
diff --git a/arch/arm/boot/dts/imx25-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx25-pinfunc.h
index 908caf810351..908caf810351 100644
--- a/arch/arm/boot/dts/imx25-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx25-pinfunc.h
diff --git a/arch/arm/boot/dts/imx25.dtsi b/arch/arm/boot/dts/nxp/imx/imx25.dtsi
index fa8044c21cb8..82601a4b7b4b 100644
--- a/arch/arm/boot/dts/imx25.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx25.dtsi
@@ -68,7 +68,17 @@
 		};
 	};
 
-	soc {
+	usbphy0: usb-phy0 {
+		compatible = "usb-nop-xceiv";
+		#phy-cells = <0>;
+	};
+
+	usbphy1: usb-phy1 {
+		compatible = "usb-nop-xceiv";
+		#phy-cells = <0>;
+	};
+
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
@@ -93,7 +103,7 @@
 				compatible = "fsl,imx25-i2c", "fsl,imx21-i2c";
 				reg = <0x43f80000 0x4000>;
 				clocks = <&clks 48>;
-				clock-names = "";
+				clock-names = "ipg";
 				interrupts = <3>;
 				status = "disabled";
 			};
@@ -104,7 +114,7 @@
 				compatible = "fsl,imx25-i2c", "fsl,imx21-i2c";
 				reg = <0x43f84000 0x4000>;
 				clocks = <&clks 48>;
-				clock-names = "";
+				clock-names = "ipg";
 				interrupts = <10>;
 				status = "disabled";
 			};
@@ -151,7 +161,7 @@
 				compatible = "fsl,imx25-i2c", "fsl,imx21-i2c";
 				reg = <0x43f98000 0x4000>;
 				clocks = <&clks 48>;
-				clock-names = "";
+				clock-names = "ipg";
 				interrupts = <4>;
 				status = "disabled";
 			};
@@ -178,12 +188,9 @@
 			};
 
 			kpp: kpp@43fa8000 {
-				#address-cells = <1>;
-				#size-cells = <0>;
 				compatible = "fsl,imx25-kpp", "fsl,imx21-kpp";
 				reg = <0x43fa8000 0x4000>;
 				clocks = <&clks 102>;
-				clock-names = "";
 				interrupts = <24>;
 				status = "disabled";
 			};
@@ -515,7 +522,7 @@
 				#interrupt-cells = <2>;
 			};
 
-			sdma: sdma@53fd4000 {
+			sdma: dma-controller@53fd4000 {
 				compatible = "fsl,imx25-sdma";
 				reg = <0x53fd4000 0x4000>;
 				clocks = <&clks 112>, <&clks 68>;
@@ -529,7 +536,6 @@
 				compatible = "fsl,imx25-wdt", "fsl,imx21-wdt";
 				reg = <0x53fdc000 0x4000>;
 				clocks = <&clks 126>;
-				clock-names = "";
 				interrupts = <55>;
 			};
 
@@ -543,7 +549,7 @@
 			};
 
 			iim: efuse@53ff0000 {
-				compatible = "fsl,imx25-iim", "fsl,imx27-iim";
+				compatible = "fsl,imx25-iim";
 				reg = <0x53ff0000 0x4000>;
 				interrupts = <19>;
 				clocks = <&clks 99>;
@@ -583,10 +589,9 @@
 			};
 
 			dryice@53ffc000 {
-				compatible = "fsl,imx25-dryice", "fsl,imx25-rtc";
+				compatible = "fsl,imx25-rtc";
 				reg = <0x53ffc000 0x4000>;
 				clocks = <&clks 81>;
-				clock-names = "ipg";
 				interrupts = <25 56>;
 			};
 		};
@@ -594,16 +599,19 @@
 		iram: sram@78000000 {
 			compatible = "mmio-sram";
 			reg = <0x78000000 0x20000>;
+			ranges = <0 0x78000000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 		};
 
-		emi@80000000 {
+		bus@80000000 {
 			compatible = "fsl,emi-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			reg = <0x80000000 0x3b002000>;
 			ranges;
 
-			nfc: nand@bb000000 {
+			nfc: nand-controller@bb000000 {
 				#address-cells = <1>;
 				#size-cells = <1>;
 
@@ -616,22 +624,4 @@
 			};
 		};
 	};
-
-	usbphy {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		usbphy0: usb-phy@0 {
-			reg = <0>;
-			compatible = "usb-nop-xceiv";
-			#phy-cells = <0>;
-		};
-
-		usbphy1: usb-phy@1 {
-			reg = <1>;
-			compatible = "usb-nop-xceiv";
-			#phy-cells = <0>;
-		};
-	};
 };
diff --git a/arch/arm/boot/dts/imx27-apf27.dts b/arch/arm/boot/dts/nxp/imx/imx27-apf27.dts
index 745d5d409952..745d5d409952 100644
--- a/arch/arm/boot/dts/imx27-apf27.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx27-apf27.dts
diff --git a/arch/arm/boot/dts/imx27-apf27dev.dts b/arch/arm/boot/dts/nxp/imx/imx27-apf27dev.dts
index 6f1e8ce9e76e..849306cb4532 100644
--- a/arch/arm/boot/dts/imx27-apf27dev.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx27-apf27dev.dts
@@ -16,7 +16,7 @@
 		fsl,pcr = <0xfae80083>;	/* non-standard but required */
 		display-timings {
 			native-mode = <&timing0>;
-			timing0: 800x480 {
+			timing0: timing0 {
 				clock-frequency = <33000033>;
 				hactive = <800>;
 				vactive = <480>;
@@ -47,26 +47,19 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		user {
+		led-user {
 			label = "Heartbeat";
 			gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_max5821: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "max5821-reg";
-			regulator-min-microvolt = <2500000>;
-			regulator-max-microvolt = <2500000>;
-			regulator-always-on;
-		};
+	reg_max5821: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "max5821-reg";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx27-eukrea-cpuimx27.dtsi b/arch/arm/boot/dts/nxp/imx/imx27-eukrea-cpuimx27.dtsi
index 74110bbcd9d4..c7e923584878 100644
--- a/arch/arm/boot/dts/imx27-eukrea-cpuimx27.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx27-eukrea-cpuimx27.dtsi
@@ -33,7 +33,7 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	pcf8563@51 {
+	rtc@51 {
 		compatible = "nxp,pcf8563";
 		reg = <0x51>;
 	};
@@ -90,7 +90,7 @@
 &weim {
 	status = "okay";
 
-	nor: nor@0,0 {
+	nor: flash@0,0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "cfi-flash";
diff --git a/arch/arm/boot/dts/imx27-eukrea-mbimxsd27-baseboard.dts b/arch/arm/boot/dts/nxp/imx/imx27-eukrea-mbimxsd27-baseboard.dts
index 9c3ec82ec7e5..d78793601306 100644
--- a/arch/arm/boot/dts/imx27-eukrea-mbimxsd27-baseboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx27-eukrea-mbimxsd27-baseboard.dts
@@ -16,7 +16,7 @@
 
 		display-timings {
 			native-mode = <&timing0>;
-			timing0: 320x240 {
+			timing0: timing0 {
 				clock-frequency = <6500000>;
 				hactive = <320>;
 				vactive = <240>;
@@ -54,22 +54,15 @@
 		};
 	};
 
-	regulators {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "simple-bus";
-
-		reg_lcd: regulator@0 {
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_lcdreg>;
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "LCD";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio1 25 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	reg_lcd: regulator-0 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lcdreg>;
+		regulator-name = "LCD";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 25 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx27-pdk.dts b/arch/arm/boot/dts/nxp/imx/imx27-pdk.dts
index 35123b7cb6b3..21d436972aa4 100644
--- a/arch/arm/boot/dts/imx27-pdk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx27-pdk.dts
@@ -14,18 +14,12 @@
 		reg = <0xa0000000 0x08000000>;
 	};
 
-	usbphy {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		usbphy0: usbphy@0 {
-			compatible = "usb-nop-xceiv";
-			reg = <0>;
-			clocks = <&clks IMX27_CLK_DUMMY>;
-			clock-names = "main_clk";
-			#phy-cells = <0>;
-		};
+
+	usbphy0: usbphy {
+		compatible = "usb-nop-xceiv";
+		clocks = <&clks IMX27_CLK_DUMMY>;
+		clock-names = "main_clk";
+		#phy-cells = <0>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts b/arch/arm/boot/dts/nxp/imx/imx27-phytec-phycard-s-rdk.dts
index 188639738dc3..27c93b9fe049 100644
--- a/arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx27-phytec-phycard-s-rdk.dts
@@ -19,7 +19,7 @@
 		fsl,pcr = <0xf0c88080>;	/* non-standard but required */
 		display-timings {
 			native-mode = <&timing0>;
-			timing0: 640x480 {
+			timing0: timing0 {
 				hactive = <640>;
 				vactive = <480>;
 				hback-porch = <112>;
@@ -33,19 +33,12 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3v3: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3V3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	reg_3v3: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx27-phytec-phycard-s-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx27-phytec-phycard-s-som.dtsi
index 303f920201c5..31b3fc972abb 100644
--- a/arch/arm/boot/dts/imx27-phytec-phycard-s-som.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx27-phytec-phycard-s-som.dtsi
@@ -15,6 +15,22 @@
 		device_type = "memory";
 		reg = <0xa0000000 0x08000000>; /* 128MB */
 	};
+
+	usbotgphy: usbotgphy {
+		compatible = "usb-nop-xceiv";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbotgphy>;
+		reset-gpios = <&gpio2 25 GPIO_ACTIVE_LOW>;
+		#phy-cells = <0>;
+	};
+
+	usbh2phy: usbh2phy {
+		compatible = "usb-nop-xceiv";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh2phy>;
+		reset-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>;
+		#phy-cells = <0>;
+	};
 };
 
 &cspi1 {
@@ -34,7 +50,7 @@
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
 
-	at24@52 {
+	eeprom@52 {
 		compatible = "atmel,24c32";
 		pagesize = <32>;
 		reg = <0x52>;
@@ -84,6 +100,52 @@
 				MX27_PAD_NFWE_B__NFWE_B 0x0
 			>;
 		};
+
+		pinctrl_usbotgphy: usbotgphygrp {
+			fsl,pins = <
+				MX27_PAD_USBH1_RCV__GPIO2_25		0x1 /* reset gpio */
+			>;
+		};
+
+		pinctrl_usbotg: usbotggrp {
+			fsl,pins = <
+				MX27_PAD_USBOTG_CLK__USBOTG_CLK		0x0
+				MX27_PAD_USBOTG_DIR__USBOTG_DIR		0x0
+				MX27_PAD_USBOTG_NXT__USBOTG_NXT		0x0
+				MX27_PAD_USBOTG_STP__USBOTG_STP		0x0
+				MX27_PAD_USBOTG_DATA0__USBOTG_DATA0	0x0
+				MX27_PAD_USBOTG_DATA1__USBOTG_DATA1	0x0
+				MX27_PAD_USBOTG_DATA2__USBOTG_DATA2	0x0
+				MX27_PAD_USBOTG_DATA3__USBOTG_DATA3	0x0
+				MX27_PAD_USBOTG_DATA4__USBOTG_DATA4	0x0
+				MX27_PAD_USBOTG_DATA5__USBOTG_DATA5	0x0
+				MX27_PAD_USBOTG_DATA6__USBOTG_DATA6	0x0
+				MX27_PAD_USBOTG_DATA7__USBOTG_DATA7	0x0
+			>;
+		};
+
+		pinctrl_usbh2phy: usbh2phygrp {
+			fsl,pins = <
+				MX27_PAD_USBH1_SUSP__GPIO2_22		0x0 /* reset gpio */
+			>;
+		};
+
+		pinctrl_usbh2: usbh2grp {
+			fsl,pins = <
+				MX27_PAD_USBH2_CLK__USBH2_CLK		0x0
+				MX27_PAD_USBH2_DIR__USBH2_DIR		0x0
+				MX27_PAD_USBH2_NXT__USBH2_NXT		0x0
+				MX27_PAD_USBH2_STP__USBH2_STP		0x0
+				MX27_PAD_CSPI2_SCLK__USBH2_DATA0	0x0
+				MX27_PAD_CSPI2_MOSI__USBH2_DATA1	0x0
+				MX27_PAD_CSPI2_MISO__USBH2_DATA2	0x0
+				MX27_PAD_CSPI2_SS1__USBH2_DATA3		0x0
+				MX27_PAD_CSPI2_SS2__USBH2_DATA4		0x0
+				MX27_PAD_CSPI1_SS2__USBH2_DATA5		0x0
+				MX27_PAD_CSPI2_SS0__USBH2_DATA6		0x0
+				MX27_PAD_USBH2_DATA7__USBH2_DATA7	0x0
+			>;
+		};
 	};
 };
 
@@ -95,3 +157,19 @@
 	nand-on-flash-bbt;
 	status = "okay";
 };
+
+&usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	phy_type = "ulpi";
+	phys = <&usbotgphy>;
+	status = "okay";
+};
+
+&usbh2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbh2>;
+	phy_type = "ulpi";
+	phys = <&usbh2phy>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts b/arch/arm/boot/dts/nxp/imx/imx27-phytec-phycore-rdk.dts
index 344e77790152..b8048e12e3d9 100644
--- a/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx27-phytec-phycore-rdk.dts
@@ -19,7 +19,7 @@
 
 		display-timings {
 			native-mode = <&timing0>;
-			timing0: 240x320 {
+			timing0: timing0 {
 				clock-frequency = <5500000>;
 				hactive = <240>;
 				vactive = <320>;
@@ -37,29 +37,23 @@
 		};
 	};
 
-	regulators {
-		regulator@2 {
-			compatible = "regulator-fixed";
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_csien>;
-			reg = <2>;
-			regulator-name = "CSI_EN";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio2 24 GPIO_ACTIVE_LOW>;
-			regulator-always-on;
-		};
+	regulator-2 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_csien>;
+		regulator-name = "CSI_EN";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 24 GPIO_ACTIVE_LOW>;
+		regulator-always-on;
 	};
 
-	usbphy {
-		usbphy2: usbphy@2 {
-			compatible = "usb-nop-xceiv";
-			reg = <2>;
-			vcc-supply = <&reg_5v0>;
-			clocks = <&clks IMX27_CLK_DUMMY>;
-			clock-names = "main_clk";
-			#phy-cells = <0>;
-		};
+	usbphy2: usbphy {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&reg_5v0>;
+		clocks = <&clks IMX27_CLK_DUMMY>;
+		clock-names = "main_clk";
+		#phy-cells = <0>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx27-phytec-phycore-som.dtsi
index 3d10273177e9..e958d7286ae9 100644
--- a/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx27-phytec-phycore-som.dtsi
@@ -15,41 +15,27 @@
 		reg = <0xa0000000 0x08000000>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3v3: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3V3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-		};
+	reg_3v3: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
 
-		reg_5v0: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "5V0";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-		};
+	reg_5v0: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "5V0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
 	};
 
-	usbphy {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		usbphy0: usbphy@0 {
-			compatible = "usb-nop-xceiv";
-			reg = <0>;
-			vcc-supply = <&sw3_reg>;
-			clocks = <&clks IMX27_CLK_DUMMY>;
-			clock-names = "main_clk";
-			#phy-cells = <0>;
-		};
+
+	usbphy0: usbphy {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&sw3_reg>;
+		clocks = <&clks IMX27_CLK_DUMMY>;
+		clock-names = "main_clk";
+		#phy-cells = <0>;
 	};
 };
 
@@ -57,12 +43,12 @@
 	status = "okay";
 
 	/* SSI0 <=> PINS_4 (MC13783 Audio) */
-	ssi0 {
+	mux-ssi0 {
 		fsl,audmux-port = <0>;
 		fsl,port-config = <0xcb205000>;
 	};
 
-	pins4 {
+	mux-pins4 {
 		fsl,audmux-port = <2>;
 		fsl,port-config = <0x00001000>;
 	};
@@ -188,13 +174,13 @@
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
 
-	at24@52 {
+	eeprom@52 {
 		compatible = "atmel,24c32";
 		pagesize = <32>;
 		reg = <0x52>;
 	};
 
-	pcf8563@51 {
+	rtc@51 {
 		compatible = "nxp,pcf8563";
 		reg = <0x51>;
 	};
@@ -322,7 +308,7 @@
 &weim {
 	status = "okay";
 
-	nor: nor@0,0 {
+	nor: flash@0,0 {
 		compatible = "cfi-flash";
 		reg = <0 0x00000000 0x02000000>;
 		bank-width = <2>;
diff --git a/arch/arm/boot/dts/imx27-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx27-pinfunc.h
index 75aea0c701d4..75aea0c701d4 100644
--- a/arch/arm/boot/dts/imx27-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx27-pinfunc.h
diff --git a/arch/arm/boot/dts/imx27.dtsi b/arch/arm/boot/dts/nxp/imx/imx27.dtsi
index fd525c3b16fa..989b7659b669 100644
--- a/arch/arm/boot/dts/imx27.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx27.dtsi
@@ -74,21 +74,21 @@
 		};
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
 		interrupt-parent = <&aitc>;
 		ranges;
 
-		aipi@10000000 { /* AIPI1 */
+		aipi1: bus@10000000 { /* AIPI1 */
 			compatible = "fsl,aipi-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			reg = <0x10000000 0x20000>;
 			ranges;
 
-			dma: dma@10001000 {
+			dma: dma-controller@10001000 {
 				compatible = "fsl,imx27-dma";
 				reg = <0x10001000 0x1000>;
 				interrupts = <32>;
@@ -96,7 +96,7 @@
 					 <&clks IMX27_CLK_DMA_AHB_GATE>;
 				clock-names = "ipg", "ahb";
 				#dma-cells = <1>;
-				#dma-channels = <16>;
+				dma-channels = <16>;
 			};
 
 			wdog: watchdog@10002000 {
@@ -453,7 +453,7 @@
 			};
 		};
 
-		aipi@10020000 { /* AIPI2 */
+		aipi2: bus@10020000 { /* AIPI2 */
 			compatible = "fsl,aipi-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -534,7 +534,7 @@
 				clock-names = "ipg", "ahb";
 			};
 
-			clks: ccm@10027000{
+			clks: ccm@10027000 {
 				compatible = "fsl,imx27-ccm";
 				reg = <0x10027000 0x1000>;
 				#clock-cells = <1>;
@@ -568,7 +568,7 @@
 			status = "disabled";
 		};
 
-		weim: weim@d8002000 {
+		weim: memory-controller@d8002000 {
 			#address-cells = <2>;
 			#size-cells = <1>;
 			compatible = "fsl,imx27-weim";
@@ -588,6 +588,9 @@
 		iram: sram@ffff4c00 {
 			compatible = "mmio-sram";
 			reg = <0xffff4c00 0xb400>;
+			ranges = <0 0xffff4c00 0xb400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/imx31-bug.dts b/arch/arm/boot/dts/nxp/imx/imx31-bug.dts
index d87eee3f9b3c..d87eee3f9b3c 100644
--- a/arch/arm/boot/dts/imx31-bug.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx31-bug.dts
diff --git a/arch/arm/boot/dts/imx31-lite.dts b/arch/arm/boot/dts/nxp/imx/imx31-lite.dts
index d17abdfb6330..630f8fa69ba8 100644
--- a/arch/arm/boot/dts/imx31-lite.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx31-lite.dts
@@ -157,7 +157,7 @@
 &weim {
 	status = "okay";
 
-	nor@0,0 {
+	flash@0,0 {
 		compatible = "cfi-flash";
 		reg = <0 0x0 0x200000>;
 		bank-width = <2>;
diff --git a/arch/arm/boot/dts/imx31.dtsi b/arch/arm/boot/dts/nxp/imx/imx31.dtsi
index 2adb923c0b27..8541a666747a 100644
--- a/arch/arm/boot/dts/imx31.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx31.dtsi
@@ -48,7 +48,7 @@
 		reg = <0x68000000 0x100000>;
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
@@ -63,7 +63,7 @@
 			ranges = <0 0x1fffc000 0x4000>;
 		};
 
-		bus@43f00000 { /* AIPS1 */
+		aips1: bus@43f00000 { /* AIPS1 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -218,7 +218,7 @@
 			};
 
 			iim: efuse@5001c000 {
-				compatible = "fsl,imx31-iim", "fsl,imx27-iim";
+				compatible = "fsl,imx31-iim";
 				reg = <0x5001c000 0x1000>;
 				interrupts = <19>;
 				clocks = <&clks 25>;
@@ -232,7 +232,7 @@
 			reg = <0x53f00000 0x100000>;
 			ranges;
 
-			clks: ccm@53f80000{
+			clks: ccm@53f80000 {
 				compatible = "fsl,imx31-ccm";
 				reg = <0x53f80000 0x4000>;
 				interrupts = <31>, <53>;
@@ -297,7 +297,7 @@
 				#interrupt-cells = <2>;
 			};
 
-			sdma: sdma@53fd4000 {
+			sdma: dma-controller@53fd4000 {
 				compatible = "fsl,imx31-sdma";
 				reg = <0x53fd4000 0x4000>;
 				interrupts = <34>;
@@ -340,7 +340,7 @@
 			#address-cells = <1>;
 			#size-cells = <1>;
 
-			nfc: nand@b8000000 {
+			nfc: nand-controller@b8000000 {
 				compatible = "fsl,imx31-nand", "fsl,imx27-nand";
 				reg = <0xb8000000 0x1000>;
 				interrupts = <33>;
@@ -352,7 +352,7 @@
 				status = "disabled";
 			};
 
-			weim: weim@b8002000 {
+			weim: memory-controller@b8002000 {
 				compatible = "fsl,imx31-weim", "fsl,imx27-weim";
 				reg = <0xb8002000 0x1000>;
 				clocks = <&clks 56>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx35-eukrea-cpuimx35.dtsi b/arch/arm/boot/dts/nxp/imx/imx35-eukrea-cpuimx35.dtsi
new file mode 100644
index 000000000000..0064b5452b54
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx35-eukrea-cpuimx35.dtsi
@@ -0,0 +1,87 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Eukréa Electromatique <denis@eukrea.com>
+ */
+
+#include "imx35.dtsi"
+
+/ {
+	model = "Eukrea CPUIMX35";
+	compatible = "eukrea,cpuimx35", "fsl,imx35";
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x8000000>; /* 128M */
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+
+	tsc2007: tsc2007@48 {
+		compatible = "ti,tsc2007";
+		gpios = <&gpio3 2 0>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <0x2 0x8>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tsc2007_1>;
+		reg = <0x48>;
+		ti,x-plate-ohms = <180>;
+	};
+};
+
+&iomuxc {
+	pinctrl_fec: fecgrp {
+		fsl,pins = <
+			MX35_PAD_FEC_TX_CLK__FEC_TX_CLK		0x80000000
+			MX35_PAD_FEC_RX_CLK__FEC_RX_CLK		0x80000000
+			MX35_PAD_FEC_RX_DV__FEC_RX_DV		0x80000000
+			MX35_PAD_FEC_COL__FEC_COL		0x80000000
+			MX35_PAD_FEC_RDATA0__FEC_RDATA_0	0x80000000
+			MX35_PAD_FEC_TDATA0__FEC_TDATA_0	0x80000000
+			MX35_PAD_FEC_TX_EN__FEC_TX_EN		0x80000000
+			MX35_PAD_FEC_MDC__FEC_MDC		0x80000000
+			MX35_PAD_FEC_MDIO__FEC_MDIO		0x80000000
+			MX35_PAD_FEC_TX_ERR__FEC_TX_ERR		0x80000000
+			MX35_PAD_FEC_RX_ERR__FEC_RX_ERR		0x80000000
+			MX35_PAD_FEC_CRS__FEC_CRS		0x80000000
+			MX35_PAD_FEC_RDATA1__FEC_RDATA_1	0x80000000
+			MX35_PAD_FEC_TDATA1__FEC_TDATA_1	0x80000000
+			MX35_PAD_FEC_RDATA2__FEC_RDATA_2	0x80000000
+			MX35_PAD_FEC_TDATA2__FEC_TDATA_2	0x80000000
+			MX35_PAD_FEC_RDATA3__FEC_RDATA_3	0x80000000
+			MX35_PAD_FEC_TDATA3__FEC_TDATA_3	0x80000000
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX35_PAD_I2C1_CLK__I2C1_SCL		0x80000000
+			MX35_PAD_I2C1_DAT__I2C1_SDA		0x80000000
+		>;
+	};
+
+	pinctrl_tsc2007_1: tsc2007-1-grp {
+		fsl,pins = <MX35_PAD_ATA_DA2__GPIO3_2 0x80000000>;
+	};
+};
+
+&nfc {
+	nand-bus-width = <8>;
+	nand-ecc-mode = "hw";
+	nand-on-flash-bbt;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx35-eukrea-mbimxsd35-baseboard.dts b/arch/arm/boot/dts/nxp/imx/imx35-eukrea-mbimxsd35-baseboard.dts
index b1c11170ac25..e7835a769bbc 100644
--- a/arch/arm/boot/dts/imx35-eukrea-mbimxsd35-baseboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx35-eukrea-mbimxsd35-baseboard.dts
@@ -13,12 +13,12 @@
 	model = "Eukrea CPUIMX35";
 	compatible = "eukrea,mbimxsd35-baseboard", "eukrea,cpuimx35", "fsl,imx35";
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_bp1>;
 
-		bp1 {
+		button {
 			label = "BP1";
 			gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_MISC>;
@@ -69,57 +69,55 @@
 };
 
 &iomuxc {
-	imx35-eukrea {
-		pinctrl_audmux: audmuxgrp {
-			fsl,pins = <
-				MX35_PAD_STXFS4__AUDMUX_AUD4_TXFS	0x80000000
-				MX35_PAD_STXD4__AUDMUX_AUD4_TXD		0x80000000
-				MX35_PAD_SRXD4__AUDMUX_AUD4_RXD		0x80000000
-				MX35_PAD_SCK4__AUDMUX_AUD4_TXC		0x80000000
-			>;
-		};
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX35_PAD_STXFS4__AUDMUX_AUD4_TXFS	0x80000000
+			MX35_PAD_STXD4__AUDMUX_AUD4_TXD		0x80000000
+			MX35_PAD_SRXD4__AUDMUX_AUD4_RXD		0x80000000
+			MX35_PAD_SCK4__AUDMUX_AUD4_TXC		0x80000000
+		>;
+	};
 
-		pinctrl_bp1: bp1grp {
-			fsl,pins = <MX35_PAD_LD19__GPIO3_25  0x80000000>;
-		};
+	pinctrl_bp1: bp1grp {
+		fsl,pins = <MX35_PAD_LD19__GPIO3_25  0x80000000>;
+	};
 
-		pinctrl_esdhc1: esdhc1grp {
-			fsl,pins = <
-				MX35_PAD_SD1_CMD__ESDHC1_CMD		0x80000000
-				MX35_PAD_SD1_CLK__ESDHC1_CLK		0x80000000
-				MX35_PAD_SD1_DATA0__ESDHC1_DAT0		0x80000000
-				MX35_PAD_SD1_DATA1__ESDHC1_DAT1		0x80000000
-				MX35_PAD_SD1_DATA2__ESDHC1_DAT2		0x80000000
-				MX35_PAD_SD1_DATA3__ESDHC1_DAT3		0x80000000
-				MX35_PAD_LD18__GPIO3_24			0x80000000 /* CD */
-			>;
-		};
+	pinctrl_esdhc1: esdhc1grp {
+		fsl,pins = <
+			MX35_PAD_SD1_CMD__ESDHC1_CMD		0x80000000
+			MX35_PAD_SD1_CLK__ESDHC1_CLK		0x80000000
+			MX35_PAD_SD1_DATA0__ESDHC1_DAT0		0x80000000
+			MX35_PAD_SD1_DATA1__ESDHC1_DAT1		0x80000000
+			MX35_PAD_SD1_DATA2__ESDHC1_DAT2		0x80000000
+			MX35_PAD_SD1_DATA3__ESDHC1_DAT3		0x80000000
+			MX35_PAD_LD18__GPIO3_24			0x80000000 /* CD */
+		>;
+	};
 
-		pinctrl_led1: led1grp {
-			fsl,pins = <MX35_PAD_LD23__GPIO3_29  0x80000000>;
-		};
+	pinctrl_led1: led1grp {
+		fsl,pins = <MX35_PAD_LD23__GPIO3_29  0x80000000>;
+	};
 
-		pinctrl_reg_lcd_3v3: reg-lcd-3v3 {
-			fsl,pins = <MX35_PAD_D3_CLS__GPIO1_4 0x80000000>;
-		};
+	pinctrl_reg_lcd_3v3: reg-lcd-3v3grp {
+		fsl,pins = <MX35_PAD_D3_CLS__GPIO1_4 0x80000000>;
+	};
 
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX35_PAD_TXD1__UART1_TXD_MUX		0x1c5
-				MX35_PAD_RXD1__UART1_RXD_MUX		0x1c5
-				MX35_PAD_CTS1__UART1_CTS		0x1c5
-				MX35_PAD_RTS1__UART1_RTS		0x1c5
-			>;
-		};
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX35_PAD_TXD1__UART1_TXD_MUX		0x1c5
+			MX35_PAD_RXD1__UART1_RXD_MUX		0x1c5
+			MX35_PAD_CTS1__UART1_CTS		0x1c5
+			MX35_PAD_RTS1__UART1_RTS		0x1c5
+		>;
+	};
 
-		pinctrl_uart2: uart2grp {
-			fsl,pins = <
-				MX35_PAD_RXD2__UART2_RXD_MUX		0x1c5
-				MX35_PAD_TXD2__UART2_TXD_MUX		0x1c5
-				MX35_PAD_RTS2__UART2_RTS		0x1c5
-				MX35_PAD_CTS2__UART2_CTS		0x1c5
-			>;
-		};
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX35_PAD_RXD2__UART2_RXD_MUX		0x1c5
+			MX35_PAD_TXD2__UART2_TXD_MUX		0x1c5
+			MX35_PAD_RTS2__UART2_RTS		0x1c5
+			MX35_PAD_CTS2__UART2_CTS		0x1c5
+		>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx35-pdk.dts b/arch/arm/boot/dts/nxp/imx/imx35-pdk.dts
index ddce0a844758..a2baf8202f94 100644
--- a/arch/arm/boot/dts/imx35-pdk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx35-pdk.dts
@@ -24,26 +24,24 @@
 };
 
 &iomuxc {
-	imx35-pdk {
-		pinctrl_esdhc1: esdhc1grp {
-			fsl,pins = <
-				MX35_PAD_SD1_CMD__ESDHC1_CMD		0x80000000
-				MX35_PAD_SD1_CLK__ESDHC1_CLK		0x80000000
-				MX35_PAD_SD1_DATA0__ESDHC1_DAT0		0x80000000
-				MX35_PAD_SD1_DATA1__ESDHC1_DAT1		0x80000000
-				MX35_PAD_SD1_DATA2__ESDHC1_DAT2		0x80000000
-				MX35_PAD_SD1_DATA3__ESDHC1_DAT3		0x80000000
-			>;
-		};
-
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX35_PAD_TXD1__UART1_TXD_MUX		0x1c5
-				MX35_PAD_RXD1__UART1_RXD_MUX		0x1c5
-				MX35_PAD_CTS1__UART1_CTS		0x1c5
-				MX35_PAD_RTS1__UART1_RTS		0x1c5
-			>;
-		};
+	pinctrl_esdhc1: esdhc1grp {
+		fsl,pins = <
+			MX35_PAD_SD1_CMD__ESDHC1_CMD		0x80000000
+			MX35_PAD_SD1_CLK__ESDHC1_CLK		0x80000000
+			MX35_PAD_SD1_DATA0__ESDHC1_DAT0		0x80000000
+			MX35_PAD_SD1_DATA1__ESDHC1_DAT1		0x80000000
+			MX35_PAD_SD1_DATA2__ESDHC1_DAT2		0x80000000
+			MX35_PAD_SD1_DATA3__ESDHC1_DAT3		0x80000000
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX35_PAD_TXD1__UART1_TXD_MUX		0x1c5
+			MX35_PAD_RXD1__UART1_RXD_MUX		0x1c5
+			MX35_PAD_CTS1__UART1_CTS		0x1c5
+			MX35_PAD_RTS1__UART1_RTS		0x1c5
+		>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx35-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx35-pinfunc.h
index 9d6cc9564b72..9d6cc9564b72 100644
--- a/arch/arm/boot/dts/imx35-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx35-pinfunc.h
diff --git a/arch/arm/boot/dts/imx35.dtsi b/arch/arm/boot/dts/nxp/imx/imx35.dtsi
index 8e41c8b7bd70..111d7c0331f5 100644
--- a/arch/arm/boot/dts/imx35.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx35.dtsi
@@ -156,7 +156,7 @@
 				status = "disabled";
 			};
 
-			iomuxc: iomuxc@43fac000 {
+			iomuxc: pinctrl@43fac000 {
 				compatible = "fsl,imx35-iomuxc";
 				reg = <0x43fac000 0x4000>;
 			};
@@ -284,7 +284,7 @@
 				#interrupt-cells = <2>;
 			};
 
-			sdma: sdma@53fd4000 {
+			sdma: dma-controller@53fd4000 {
 				compatible = "fsl,imx35-sdma";
 				reg = <0x53fd4000 0x4000>;
 				clocks = <&clks 9>, <&clks 65>;
@@ -298,7 +298,6 @@
 				compatible = "fsl,imx35-wdt", "fsl,imx21-wdt";
 				reg = <0x53fdc000 0x4000>;
 				clocks = <&clks 74>;
-				clock-names = "";
 				interrupts = <55>;
 			};
 
@@ -364,7 +363,7 @@
 			reg = <0x80000000 0x40000000>;
 			ranges;
 
-			nfc: nand@bb000000 {
+			nfc: nand-controller@bb000000 {
 				#address-cells = <1>;
 				#size-cells = <1>;
 				compatible = "fsl,imx35-nand", "fsl,imx25-nand";
@@ -375,7 +374,7 @@
 				status = "disabled";
 			};
 
-			weim: weim@b8002000 {
+			weim: memory-controller@b8002000 {
 				#address-cells = <2>;
 				#size-cells = <1>;
 				clocks = <&clks 0>;
diff --git a/arch/arm/boot/dts/imx50-evk.dts b/arch/arm/boot/dts/nxp/imx/imx50-evk.dts
index 4ea5c23f181b..f40b0d5fdb85 100644
--- a/arch/arm/boot/dts/imx50-evk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx50-evk.dts
@@ -23,7 +23,7 @@
 	cs-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>, <&gpio4 13 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
-	flash: m25p32@1 {
+	flash: flash@1 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p32", "jedec,spi-nor";
@@ -52,40 +52,38 @@
 };
 
 &iomuxc {
-	imx50-evk {
-		pinctrl_cspi: cspigrp {
-			fsl,pins = <
-				MX50_PAD_CSPI_SCLK__CSPI_SCLK		0x00
-				MX50_PAD_CSPI_MISO__CSPI_MISO		0x00
-				MX50_PAD_CSPI_MOSI__CSPI_MOSI		0x00
-				MX50_PAD_CSPI_SS0__GPIO4_11		0xc4
-				MX50_PAD_ECSPI1_MOSI__GPIO4_13		0x84
-			>;
-		};
+	pinctrl_cspi: cspigrp {
+		fsl,pins = <
+			MX50_PAD_CSPI_SCLK__CSPI_SCLK		0x00
+			MX50_PAD_CSPI_MISO__CSPI_MISO		0x00
+			MX50_PAD_CSPI_MOSI__CSPI_MOSI		0x00
+			MX50_PAD_CSPI_SS0__GPIO4_11		0xc4
+			MX50_PAD_ECSPI1_MOSI__GPIO4_13		0x84
+		>;
+	};
 
-		pinctrl_fec: fecgrp {
-			fsl,pins = <
-				MX50_PAD_SSI_RXFS__FEC_MDC		0x80
-				MX50_PAD_SSI_RXC__FEC_MDIO		0x80
-				MX50_PAD_DISP_D0__FEC_TX_CLK		0x80
-				MX50_PAD_DISP_D1__FEC_RX_ERR		0x80
-				MX50_PAD_DISP_D2__FEC_RX_DV		0x80
-				MX50_PAD_DISP_D3__FEC_RDATA_1		0x80
-				MX50_PAD_DISP_D4__FEC_RDATA_0		0x80
-				MX50_PAD_DISP_D5__FEC_TX_EN		0x80
-				MX50_PAD_DISP_D6__FEC_TDATA_1		0x80
-				MX50_PAD_DISP_D7__FEC_TDATA_0		0x80
-			>;
-		};
+	pinctrl_fec: fecgrp {
+		fsl,pins = <
+			MX50_PAD_SSI_RXFS__FEC_MDC		0x80
+			MX50_PAD_SSI_RXC__FEC_MDIO		0x80
+			MX50_PAD_DISP_D0__FEC_TX_CLK		0x80
+			MX50_PAD_DISP_D1__FEC_RX_ERR		0x80
+			MX50_PAD_DISP_D2__FEC_RX_DV		0x80
+			MX50_PAD_DISP_D3__FEC_RDATA_1		0x80
+			MX50_PAD_DISP_D4__FEC_RDATA_0		0x80
+			MX50_PAD_DISP_D5__FEC_TX_EN		0x80
+			MX50_PAD_DISP_D6__FEC_TDATA_1		0x80
+			MX50_PAD_DISP_D7__FEC_TDATA_0		0x80
+		>;
+	};
 
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX50_PAD_UART1_TXD__UART1_TXD_MUX	0x1e4
-				MX50_PAD_UART1_RXD__UART1_RXD_MUX	0x1e4
-				MX50_PAD_UART1_RTS__UART1_RTS		0x1e4
-				MX50_PAD_UART1_CTS__UART1_CTS		0x1e4
-			>;
-		};
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX50_PAD_UART1_TXD__UART1_TXD_MUX	0x1e4
+			MX50_PAD_UART1_RXD__UART1_RXD_MUX	0x1e4
+			MX50_PAD_UART1_RTS__UART1_RTS		0x1e4
+			MX50_PAD_UART1_CTS__UART1_CTS		0x1e4
+		>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx50-kobo-aura.dts b/arch/arm/boot/dts/nxp/imx/imx50-kobo-aura.dts
index 82ce8c43be86..b1a6a9c58ac3 100644
--- a/arch/arm/boot/dts/imx50-kobo-aura.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx50-kobo-aura.dts
@@ -26,7 +26,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_leds>;
 
-		on {
+		led-on {
 			label = "kobo_aura:orange:on";
 			gpios = <&gpio6 24 GPIO_ACTIVE_LOW>;
 			panic-indicator;
@@ -38,20 +38,20 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpiokeys>;
 
-		power {
+		key-power {
 			label = "Power Button";
 			gpios = <&gpio4 10 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 		};
 
-		hallsensor {
+		event-hallsensor {
 			label = "Hallsensor";
 			gpios = <&gpio5 15 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_RESERVED>;
 			linux,input-type = <EV_SW>;
 		};
 
-		frontlight {
+		event-frontlight {
 			label = "Frontlight";
 			gpios = <&gpio4 1 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_DISPLAYTOGGLE>;
@@ -73,7 +73,7 @@
 		states = <3300000 0>;
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
-		enable-gpio = <&gpio4 12 GPIO_ACTIVE_LOW>;
+		enable-gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
 		startup-delay-us = <100000>;
 	};
 };
diff --git a/arch/arm/boot/dts/imx50-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx50-pinfunc.h
index 5e6b30247543..5e6b30247543 100644
--- a/arch/arm/boot/dts/imx50-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx50-pinfunc.h
diff --git a/arch/arm/boot/dts/imx50.dtsi b/arch/arm/boot/dts/nxp/imx/imx50.dtsi
index be0de0fd31f9..d76c496b3f71 100644
--- a/arch/arm/boot/dts/imx50.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx50.dtsi
@@ -94,14 +94,14 @@
 		status = "okay";
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
 		interrupt-parent = <&tzic>;
 		ranges;
 
-		bus@50000000 { /* AIPS1 */
+		aips1: bus@50000000 { /* AIPS1 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -283,7 +283,7 @@
 				clock-names = "ipg", "per";
 			};
 
-			iomuxc: iomuxc@53fa8000 {
+			iomuxc: pinctrl@53fa8000 {
 				compatible = "fsl,imx50-iomuxc", "fsl,imx53-iomuxc";
 				reg = <0x53fa8000 0x4000>;
 			};
@@ -335,10 +335,10 @@
 				#reset-cells = <1>;
 			};
 
-			clks: ccm@53fd4000{
+			clks: ccm@53fd4000 {
 				compatible = "fsl,imx50-ccm";
 				reg = <0x53fd4000 0x4000>;
-				interrupts = <0 71 0x04 0 72 0x04>;
+				interrupts = <71>, <72>;
 				#clock-cells = <1>;
 			};
 
@@ -385,7 +385,7 @@
 			};
 		};
 
-		bus@60000000 {	/* AIPS2 */
+		aips2: bus@60000000 {	/* AIPS2 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -421,7 +421,7 @@
 				status = "disabled";
 			};
 
-			sdma: sdma@63fb0000 {
+			sdma: dma-controller@63fb0000 {
 				compatible = "fsl,imx50-sdma", "fsl,imx35-sdma";
 				reg = <0x63fb0000 0x4000>;
 				interrupts = <6>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx51-apf51.dts b/arch/arm/boot/dts/nxp/imx/imx51-apf51.dts
new file mode 100644
index 000000000000..670e13136f1f
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx51-apf51.dts
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 Armadeus Systems - <support@armadeus.com>
+ * Copyright 2012 Laurent Cans <laurent.cans@gmail.com>
+ *
+ * Based on mx51-babbage.dts
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ */
+
+/dts-v1/;
+#include "imx51.dtsi"
+
+/ {
+	model = "Armadeus Systems APF51 module";
+	compatible = "armadeus,imx51-apf51", "fsl,imx51";
+
+	memory@90000000 {
+		device_type = "memory";
+		reg = <0x90000000 0x20000000>;
+	};
+
+	clocks {
+		osc {
+			clock-frequency = <33554432>;
+		};
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec>;
+	phy-mode = "mii";
+	phy-reset-gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <1>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_fec: fecgrp {
+		fsl,pins = <
+			MX51_PAD_DI_GP3__FEC_TX_ER		0x80000000
+			MX51_PAD_DI2_PIN4__FEC_CRS		0x80000000
+			MX51_PAD_DI2_PIN2__FEC_MDC		0x80000000
+			MX51_PAD_DI2_PIN3__FEC_MDIO		0x80000000
+			MX51_PAD_DI2_DISP_CLK__FEC_RDATA1	0x80000000
+			MX51_PAD_DI_GP4__FEC_RDATA2		0x80000000
+			MX51_PAD_DISP2_DAT0__FEC_RDATA3		0x80000000
+			MX51_PAD_DISP2_DAT1__FEC_RX_ER		0x80000000
+			MX51_PAD_DISP2_DAT6__FEC_TDATA1		0x80000000
+			MX51_PAD_DISP2_DAT7__FEC_TDATA2		0x80000000
+			MX51_PAD_DISP2_DAT8__FEC_TDATA3		0x80000000
+			MX51_PAD_DISP2_DAT9__FEC_TX_EN		0x80000000
+			MX51_PAD_DISP2_DAT10__FEC_COL		0x80000000
+			MX51_PAD_DISP2_DAT11__FEC_RX_CLK	0x80000000
+			MX51_PAD_DISP2_DAT12__FEC_RX_DV		0x80000000
+			MX51_PAD_DISP2_DAT13__FEC_TX_CLK	0x80000000
+			MX51_PAD_DISP2_DAT14__FEC_RDATA0	0x80000000
+			MX51_PAD_DISP2_DAT15__FEC_TDATA0	0x80000000
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX51_PAD_UART3_RXD__UART3_RXD		0x1c5
+			MX51_PAD_UART3_TXD__UART3_TXD		0x1c5
+		>;
+	};
+};
+
+&nfc {
+	nand-bus-width = <8>;
+	nand-ecc-mode = "hw";
+	nand-on-flash-bbt;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx51-apf51dev.dts b/arch/arm/boot/dts/nxp/imx/imx51-apf51dev.dts
new file mode 100644
index 000000000000..6ebd80e30683
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx51-apf51dev.dts
@@ -0,0 +1,215 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Armadeus Systems - <support@armadeus.com>
+ */
+
+/* APF51Dev is a docking board for the APF51 SOM */
+#include "imx51-apf51.dts"
+
+/ {
+	model = "Armadeus Systems APF51Dev docking/development board";
+	compatible = "armadeus,imx51-apf51dev", "armadeus,imx51-apf51", "fsl,imx51";
+
+	backlight {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight>;
+		compatible = "gpio-backlight";
+		gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>;
+		default-on;
+	};
+
+	disp1 {
+		compatible = "fsl,imx-parallel-display";
+		interface-pix-fmt = "bgr666";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu_disp1>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing-lw700 {
+				clock-frequency = <33000033>;
+				hactive = <800>;
+				vactive = <480>;
+				hback-porch = <96>;
+				hfront-porch = <96>;
+				vback-porch = <20>;
+				vfront-porch = <21>;
+				hsync-len = <64>;
+				vsync-len = <4>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+				de-active = <1>;
+				pixelclk-active = <0>;
+			};
+		};
+
+		port {
+			display_in: endpoint {
+				remote-endpoint = <&ipu_di0_disp1>;
+			};
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		user-key {
+			label = "user";
+			gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
+			linux,code = <256>; /* BTN_0 */
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-user {
+			label = "Heartbeat";
+			gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>,
+		   <&gpio4 25 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	cs-gpios = <&gpio3 28 GPIO_ACTIVE_LOW>,
+		   <&gpio3 27 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&esdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc1>;
+	cd-gpios = <&gpio2 29 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&esdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc2>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_backlight: backlightgrp {
+		fsl,pins = <
+			MX51_PAD_DI1_D1_CS__GPIO3_4 0x1F5
+		>;
+	};
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX51_PAD_EIM_EB2__GPIO2_22   0x0C5
+			MX51_PAD_EIM_EB3__GPIO2_23   0x0C5
+			MX51_PAD_EIM_CS4__GPIO2_29   0x100
+			MX51_PAD_NANDF_D13__GPIO3_27 0x0C5
+			MX51_PAD_NANDF_D12__GPIO3_28 0x0C5
+			MX51_PAD_CSPI1_SS0__GPIO4_24 0x0C5
+			MX51_PAD_CSPI1_SS1__GPIO4_25 0x0C5
+			MX51_PAD_GPIO1_2__GPIO1_2    0x0C5
+			MX51_PAD_GPIO1_3__GPIO1_3    0x0C5
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX51_PAD_CSPI1_MISO__ECSPI1_MISO	0x185
+			MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI	0x185
+			MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK	0x185
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX51_PAD_NANDF_RB3__ECSPI2_MISO		0x185
+			MX51_PAD_NANDF_D15__ECSPI2_MOSI		0x185
+			MX51_PAD_NANDF_RB2__ECSPI2_SCLK		0x185
+		>;
+	};
+
+	pinctrl_esdhc1: esdhc1grp {
+		fsl,pins = <
+			MX51_PAD_SD1_CMD__SD1_CMD		0x400020d5
+			MX51_PAD_SD1_CLK__SD1_CLK		0x20d5
+			MX51_PAD_SD1_DATA0__SD1_DATA0		0x20d5
+			MX51_PAD_SD1_DATA1__SD1_DATA1		0x20d5
+			MX51_PAD_SD1_DATA2__SD1_DATA2		0x20d5
+			MX51_PAD_SD1_DATA3__SD1_DATA3		0x20d5
+		>;
+	};
+
+	pinctrl_esdhc2: esdhc2grp {
+		fsl,pins = <
+			MX51_PAD_SD2_CMD__SD2_CMD		0x400020d5
+			MX51_PAD_SD2_CLK__SD2_CLK		0x20d5
+			MX51_PAD_SD2_DATA0__SD2_DATA0		0x20d5
+			MX51_PAD_SD2_DATA1__SD2_DATA1		0x20d5
+			MX51_PAD_SD2_DATA2__SD2_DATA2		0x20d5
+			MX51_PAD_SD2_DATA3__SD2_DATA3		0x20d5
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX51_PAD_EIM_D27__I2C2_SCL		0x400001ed
+			MX51_PAD_EIM_D24__I2C2_SDA		0x400001ed
+		>;
+	};
+
+	pinctrl_ipu_disp1: ipudisp1grp {
+		fsl,pins = <
+			MX51_PAD_DISP1_DAT0__DISP1_DAT0		0x5
+			MX51_PAD_DISP1_DAT1__DISP1_DAT1		0x5
+			MX51_PAD_DISP1_DAT2__DISP1_DAT2		0x5
+			MX51_PAD_DISP1_DAT3__DISP1_DAT3		0x5
+			MX51_PAD_DISP1_DAT4__DISP1_DAT4		0x5
+			MX51_PAD_DISP1_DAT5__DISP1_DAT5		0x5
+			MX51_PAD_DISP1_DAT6__DISP1_DAT6		0x5
+			MX51_PAD_DISP1_DAT7__DISP1_DAT7		0x5
+			MX51_PAD_DISP1_DAT8__DISP1_DAT8		0x5
+			MX51_PAD_DISP1_DAT9__DISP1_DAT9		0x5
+			MX51_PAD_DISP1_DAT10__DISP1_DAT10	0x5
+			MX51_PAD_DISP1_DAT11__DISP1_DAT11	0x5
+			MX51_PAD_DISP1_DAT12__DISP1_DAT12	0x5
+			MX51_PAD_DISP1_DAT13__DISP1_DAT13	0x5
+			MX51_PAD_DISP1_DAT14__DISP1_DAT14	0x5
+			MX51_PAD_DISP1_DAT15__DISP1_DAT15	0x5
+			MX51_PAD_DISP1_DAT16__DISP1_DAT16	0x5
+			MX51_PAD_DISP1_DAT17__DISP1_DAT17	0x5
+			MX51_PAD_DISP1_DAT18__DISP1_DAT18	0x5
+			MX51_PAD_DISP1_DAT19__DISP1_DAT19	0x5
+			MX51_PAD_DISP1_DAT20__DISP1_DAT20	0x5
+			MX51_PAD_DISP1_DAT21__DISP1_DAT21	0x5
+			MX51_PAD_DISP1_DAT22__DISP1_DAT22	0x5
+			MX51_PAD_DISP1_DAT23__DISP1_DAT23	0x5
+			MX51_PAD_DI1_PIN2__DI1_PIN2		0x5
+			MX51_PAD_DI1_PIN3__DI1_PIN3		0x5
+		>;
+	};
+};
+
+&ipu_di0_disp1 {
+	remote-endpoint = <&display_in>;
+};
diff --git a/arch/arm/boot/dts/imx51-babbage.dts b/arch/arm/boot/dts/nxp/imx/imx51-babbage.dts
index 552196d8a60a..1b6ec55f9068 100644
--- a/arch/arm/boot/dts/imx51-babbage.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx51-babbage.dts
@@ -89,7 +89,7 @@
 		status = "disabled";
 		display-timings {
 			native-mode = <&timing1>;
-			timing1: claawvga {
+			timing1: timing-claawvga {
 				clock-frequency = <27000000>;
 				hactive = <800>;
 				vactive = <480>;
@@ -154,7 +154,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_keys>;
 
-		power {
+		key-power {
 			label = "Power Button";
 			gpios = <&gpio2 21 GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_POWER>;
@@ -173,22 +173,15 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_hub_reset: regulator@0 {
-			compatible = "regulator-fixed";
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_usbotgreg>;
-			reg = <0>;
-			regulator-name = "hub_reset";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	reg_hub_reset: regulator-hub-reset {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbotgreg>;
+		regulator-name = "hub_reset";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
 	};
 
 	sound {
@@ -481,246 +474,244 @@
 };
 
 &iomuxc {
-	imx51-babbage {
-		pinctrl_audmux: audmuxgrp {
-			fsl,pins = <
-				MX51_PAD_AUD3_BB_TXD__AUD3_TXD		0x80000000
-				MX51_PAD_AUD3_BB_RXD__AUD3_RXD		0x80000000
-				MX51_PAD_AUD3_BB_CK__AUD3_TXC		0x80000000
-				MX51_PAD_AUD3_BB_FS__AUD3_TXFS		0x80000000
-			>;
-		};
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX51_PAD_AUD3_BB_TXD__AUD3_TXD		0x80000000
+			MX51_PAD_AUD3_BB_RXD__AUD3_RXD		0x80000000
+			MX51_PAD_AUD3_BB_CK__AUD3_TXC		0x80000000
+			MX51_PAD_AUD3_BB_FS__AUD3_TXFS		0x80000000
+		>;
+	};
 
-		pinctrl_clk26mhz_audio: clk26mhzaudiocgrp {
-			fsl,pins = <
-				MX51_PAD_CSPI1_RDY__GPIO4_26		0x85
-			>;
-		};
+	pinctrl_clk26mhz_audio: clk26mhzaudiocgrp {
+		fsl,pins = <
+			MX51_PAD_CSPI1_RDY__GPIO4_26		0x85
+		>;
+	};
 
-		pinctrl_clk26mhz_osc: clk26mhzoscgrp {
-			fsl,pins = <
-				MX51_PAD_DI1_PIN12__GPIO3_1		0x85
-			>;
-		};
+	pinctrl_clk26mhz_osc: clk26mhzoscgrp {
+		fsl,pins = <
+			MX51_PAD_DI1_PIN12__GPIO3_1		0x85
+		>;
+	};
 
-		pinctrl_clk26mhz_usb: clk26mhzusbgrp {
-			fsl,pins = <
-				MX51_PAD_EIM_D17__GPIO2_1		0x85
-			>;
-		};
+	pinctrl_clk26mhz_usb: clk26mhzusbgrp {
+		fsl,pins = <
+			MX51_PAD_EIM_D17__GPIO2_1		0x85
+		>;
+	};
 
-		pinctrl_ecspi1: ecspi1grp {
-			fsl,pins = <
-				MX51_PAD_CSPI1_MISO__ECSPI1_MISO	0x185
-				MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI	0x185
-				MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK	0x185
-				MX51_PAD_CSPI1_SS0__GPIO4_24		0x85 /* CS0 */
-				MX51_PAD_CSPI1_SS1__GPIO4_25		0x85 /* CS1 */
-			>;
-		};
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX51_PAD_CSPI1_MISO__ECSPI1_MISO	0x185
+			MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI	0x185
+			MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK	0x185
+			MX51_PAD_CSPI1_SS0__GPIO4_24		0x85 /* CS0 */
+			MX51_PAD_CSPI1_SS1__GPIO4_25		0x85 /* CS1 */
+		>;
+	};
 
-		pinctrl_esdhc1: esdhc1grp {
-			fsl,pins = <
-				MX51_PAD_SD1_CMD__SD1_CMD		0x400020d5
-				MX51_PAD_SD1_CLK__SD1_CLK		0x20d5
-				MX51_PAD_SD1_DATA0__SD1_DATA0		0x20d5
-				MX51_PAD_SD1_DATA1__SD1_DATA1		0x20d5
-				MX51_PAD_SD1_DATA2__SD1_DATA2		0x20d5
-				MX51_PAD_SD1_DATA3__SD1_DATA3		0x20d5
-				MX51_PAD_GPIO1_0__GPIO1_0		0x100
-				MX51_PAD_GPIO1_1__GPIO1_1		0x100
-			>;
-		};
+	pinctrl_esdhc1: esdhc1grp {
+		fsl,pins = <
+			MX51_PAD_SD1_CMD__SD1_CMD		0x400020d5
+			MX51_PAD_SD1_CLK__SD1_CLK		0x20d5
+			MX51_PAD_SD1_DATA0__SD1_DATA0		0x20d5
+			MX51_PAD_SD1_DATA1__SD1_DATA1		0x20d5
+			MX51_PAD_SD1_DATA2__SD1_DATA2		0x20d5
+			MX51_PAD_SD1_DATA3__SD1_DATA3		0x20d5
+			MX51_PAD_GPIO1_0__GPIO1_0		0x100
+			MX51_PAD_GPIO1_1__GPIO1_1		0x100
+		>;
+	};
 
-		pinctrl_esdhc2: esdhc2grp {
-			fsl,pins = <
-				MX51_PAD_SD2_CMD__SD2_CMD		0x400020d5
-				MX51_PAD_SD2_CLK__SD2_CLK		0x20d5
-				MX51_PAD_SD2_DATA0__SD2_DATA0		0x20d5
-				MX51_PAD_SD2_DATA1__SD2_DATA1		0x20d5
-				MX51_PAD_SD2_DATA2__SD2_DATA2		0x20d5
-				MX51_PAD_SD2_DATA3__SD2_DATA3		0x20d5
-				MX51_PAD_GPIO1_5__GPIO1_5		0x100 /* WP */
-				MX51_PAD_GPIO1_6__GPIO1_6		0x100 /* CD */
-			>;
-		};
+	pinctrl_esdhc2: esdhc2grp {
+		fsl,pins = <
+			MX51_PAD_SD2_CMD__SD2_CMD		0x400020d5
+			MX51_PAD_SD2_CLK__SD2_CLK		0x20d5
+			MX51_PAD_SD2_DATA0__SD2_DATA0		0x20d5
+			MX51_PAD_SD2_DATA1__SD2_DATA1		0x20d5
+			MX51_PAD_SD2_DATA2__SD2_DATA2		0x20d5
+			MX51_PAD_SD2_DATA3__SD2_DATA3		0x20d5
+			MX51_PAD_GPIO1_5__GPIO1_5		0x100 /* WP */
+			MX51_PAD_GPIO1_6__GPIO1_6		0x100 /* CD */
+		>;
+	};
 
-		pinctrl_fec: fecgrp {
-			fsl,pins = <
-				MX51_PAD_EIM_EB2__FEC_MDIO		0x000001f5
-				MX51_PAD_EIM_EB3__FEC_RDATA1		0x00000085
-				MX51_PAD_EIM_CS2__FEC_RDATA2		0x00000085
-				MX51_PAD_EIM_CS3__FEC_RDATA3		0x00000085
-				MX51_PAD_EIM_CS4__FEC_RX_ER		0x00000180
-				MX51_PAD_EIM_CS5__FEC_CRS		0x00000180
-				MX51_PAD_NANDF_RB2__FEC_COL		0x00000180
-				MX51_PAD_NANDF_RB3__FEC_RX_CLK		0x00000180
-				MX51_PAD_NANDF_D9__FEC_RDATA0		0x00002180
-				MX51_PAD_NANDF_D8__FEC_TDATA0		0x00002004
-				MX51_PAD_NANDF_CS2__FEC_TX_ER		0x00002004
-				MX51_PAD_NANDF_CS3__FEC_MDC		0x00002004
-				MX51_PAD_NANDF_CS4__FEC_TDATA1		0x00002004
-				MX51_PAD_NANDF_CS5__FEC_TDATA2		0x00002004
-				MX51_PAD_NANDF_CS6__FEC_TDATA3		0x00002004
-				MX51_PAD_NANDF_CS7__FEC_TX_EN		0x00002004
-				MX51_PAD_NANDF_RDY_INT__FEC_TX_CLK	0x00002180
-				MX51_PAD_NANDF_D11__FEC_RX_DV		0x000020a4
-				MX51_PAD_EIM_A20__GPIO2_14		0x00000085 /* Phy Reset */
-			>;
-		};
+	pinctrl_fec: fecgrp {
+		fsl,pins = <
+			MX51_PAD_EIM_EB2__FEC_MDIO		0x000001f5
+			MX51_PAD_EIM_EB3__FEC_RDATA1		0x00000085
+			MX51_PAD_EIM_CS2__FEC_RDATA2		0x00000085
+			MX51_PAD_EIM_CS3__FEC_RDATA3		0x00000085
+			MX51_PAD_EIM_CS4__FEC_RX_ER		0x00000180
+			MX51_PAD_EIM_CS5__FEC_CRS		0x00000180
+			MX51_PAD_NANDF_RB2__FEC_COL		0x00000180
+			MX51_PAD_NANDF_RB3__FEC_RX_CLK		0x00000180
+			MX51_PAD_NANDF_D9__FEC_RDATA0		0x00002180
+			MX51_PAD_NANDF_D8__FEC_TDATA0		0x00002004
+			MX51_PAD_NANDF_CS2__FEC_TX_ER		0x00002004
+			MX51_PAD_NANDF_CS3__FEC_MDC		0x00002004
+			MX51_PAD_NANDF_CS4__FEC_TDATA1		0x00002004
+			MX51_PAD_NANDF_CS5__FEC_TDATA2		0x00002004
+			MX51_PAD_NANDF_CS6__FEC_TDATA3		0x00002004
+			MX51_PAD_NANDF_CS7__FEC_TX_EN		0x00002004
+			MX51_PAD_NANDF_RDY_INT__FEC_TX_CLK	0x00002180
+			MX51_PAD_NANDF_D11__FEC_RX_DV		0x000020a4
+			MX51_PAD_EIM_A20__GPIO2_14		0x00000085 /* Phy Reset */
+		>;
+	};
 
-		pinctrl_gpio_keys: gpiokeysgrp {
-			fsl,pins = <
-				MX51_PAD_EIM_A27__GPIO2_21		0x5
-			>;
-		};
+	pinctrl_gpio_keys: gpiokeysgrp {
+		fsl,pins = <
+			MX51_PAD_EIM_A27__GPIO2_21		0x5
+		>;
+	};
 
-		pinctrl_gpio_leds: gpioledsgrp {
-			fsl,pins = <
-				MX51_PAD_EIM_D22__GPIO2_6		0x80000000
-			>;
-		};
+	pinctrl_gpio_leds: gpioledsgrp {
+		fsl,pins = <
+			MX51_PAD_EIM_D22__GPIO2_6		0x80000000
+		>;
+	};
 
-		pinctrl_i2c1: i2c1grp {
-			fsl,pins = <
-				MX51_PAD_EIM_D19__I2C1_SCL		0x400001ed
-				MX51_PAD_EIM_D16__I2C1_SDA		0x400001ed
-			>;
-		};
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX51_PAD_EIM_D19__I2C1_SCL		0x400001ed
+			MX51_PAD_EIM_D16__I2C1_SDA		0x400001ed
+		>;
+	};
 
-		pinctrl_i2c2: i2c2grp {
-			fsl,pins = <
-				MX51_PAD_KEY_COL4__I2C2_SCL		0x400001ed
-				MX51_PAD_KEY_COL5__I2C2_SDA		0x400001ed
-			>;
-		};
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX51_PAD_KEY_COL4__I2C2_SCL		0x400001ed
+			MX51_PAD_KEY_COL5__I2C2_SDA		0x400001ed
+		>;
+	};
 
-		pinctrl_ipu_disp1: ipudisp1grp {
-			fsl,pins = <
-				MX51_PAD_DISP1_DAT0__DISP1_DAT0		0x5
-				MX51_PAD_DISP1_DAT1__DISP1_DAT1		0x5
-				MX51_PAD_DISP1_DAT2__DISP1_DAT2		0x5
-				MX51_PAD_DISP1_DAT3__DISP1_DAT3		0x5
-				MX51_PAD_DISP1_DAT4__DISP1_DAT4		0x5
-				MX51_PAD_DISP1_DAT5__DISP1_DAT5		0x5
-				MX51_PAD_DISP1_DAT6__DISP1_DAT6		0x5
-				MX51_PAD_DISP1_DAT7__DISP1_DAT7		0x5
-				MX51_PAD_DISP1_DAT8__DISP1_DAT8		0x5
-				MX51_PAD_DISP1_DAT9__DISP1_DAT9		0x5
-				MX51_PAD_DISP1_DAT10__DISP1_DAT10	0x5
-				MX51_PAD_DISP1_DAT11__DISP1_DAT11	0x5
-				MX51_PAD_DISP1_DAT12__DISP1_DAT12	0x5
-				MX51_PAD_DISP1_DAT13__DISP1_DAT13	0x5
-				MX51_PAD_DISP1_DAT14__DISP1_DAT14	0x5
-				MX51_PAD_DISP1_DAT15__DISP1_DAT15	0x5
-				MX51_PAD_DISP1_DAT16__DISP1_DAT16	0x5
-				MX51_PAD_DISP1_DAT17__DISP1_DAT17	0x5
-				MX51_PAD_DISP1_DAT18__DISP1_DAT18	0x5
-				MX51_PAD_DISP1_DAT19__DISP1_DAT19	0x5
-				MX51_PAD_DISP1_DAT20__DISP1_DAT20	0x5
-				MX51_PAD_DISP1_DAT21__DISP1_DAT21	0x5
-				MX51_PAD_DISP1_DAT22__DISP1_DAT22	0x5
-				MX51_PAD_DISP1_DAT23__DISP1_DAT23	0x5
-				MX51_PAD_DI1_PIN2__DI1_PIN2		0x5
-				MX51_PAD_DI1_PIN3__DI1_PIN3		0x5
-			>;
-		};
+	pinctrl_ipu_disp1: ipudisp1grp {
+		fsl,pins = <
+			MX51_PAD_DISP1_DAT0__DISP1_DAT0		0x5
+			MX51_PAD_DISP1_DAT1__DISP1_DAT1		0x5
+			MX51_PAD_DISP1_DAT2__DISP1_DAT2		0x5
+			MX51_PAD_DISP1_DAT3__DISP1_DAT3		0x5
+			MX51_PAD_DISP1_DAT4__DISP1_DAT4		0x5
+			MX51_PAD_DISP1_DAT5__DISP1_DAT5		0x5
+			MX51_PAD_DISP1_DAT6__DISP1_DAT6		0x5
+			MX51_PAD_DISP1_DAT7__DISP1_DAT7		0x5
+			MX51_PAD_DISP1_DAT8__DISP1_DAT8		0x5
+			MX51_PAD_DISP1_DAT9__DISP1_DAT9		0x5
+			MX51_PAD_DISP1_DAT10__DISP1_DAT10	0x5
+			MX51_PAD_DISP1_DAT11__DISP1_DAT11	0x5
+			MX51_PAD_DISP1_DAT12__DISP1_DAT12	0x5
+			MX51_PAD_DISP1_DAT13__DISP1_DAT13	0x5
+			MX51_PAD_DISP1_DAT14__DISP1_DAT14	0x5
+			MX51_PAD_DISP1_DAT15__DISP1_DAT15	0x5
+			MX51_PAD_DISP1_DAT16__DISP1_DAT16	0x5
+			MX51_PAD_DISP1_DAT17__DISP1_DAT17	0x5
+			MX51_PAD_DISP1_DAT18__DISP1_DAT18	0x5
+			MX51_PAD_DISP1_DAT19__DISP1_DAT19	0x5
+			MX51_PAD_DISP1_DAT20__DISP1_DAT20	0x5
+			MX51_PAD_DISP1_DAT21__DISP1_DAT21	0x5
+			MX51_PAD_DISP1_DAT22__DISP1_DAT22	0x5
+			MX51_PAD_DISP1_DAT23__DISP1_DAT23	0x5
+			MX51_PAD_DI1_PIN2__DI1_PIN2		0x5
+			MX51_PAD_DI1_PIN3__DI1_PIN3		0x5
+		>;
+	};
 
-		pinctrl_ipu_disp2: ipudisp2grp {
-			fsl,pins = <
-				MX51_PAD_DISP2_DAT0__DISP2_DAT0		0x5
-				MX51_PAD_DISP2_DAT1__DISP2_DAT1		0x5
-				MX51_PAD_DISP2_DAT2__DISP2_DAT2		0x5
-				MX51_PAD_DISP2_DAT3__DISP2_DAT3		0x5
-				MX51_PAD_DISP2_DAT4__DISP2_DAT4		0x5
-				MX51_PAD_DISP2_DAT5__DISP2_DAT5		0x5
-				MX51_PAD_DISP2_DAT6__DISP2_DAT6		0x5
-				MX51_PAD_DISP2_DAT7__DISP2_DAT7		0x5
-				MX51_PAD_DISP2_DAT8__DISP2_DAT8		0x5
-				MX51_PAD_DISP2_DAT9__DISP2_DAT9		0x5
-				MX51_PAD_DISP2_DAT10__DISP2_DAT10	0x5
-				MX51_PAD_DISP2_DAT11__DISP2_DAT11	0x5
-				MX51_PAD_DISP2_DAT12__DISP2_DAT12	0x5
-				MX51_PAD_DISP2_DAT13__DISP2_DAT13	0x5
-				MX51_PAD_DISP2_DAT14__DISP2_DAT14	0x5
-				MX51_PAD_DISP2_DAT15__DISP2_DAT15	0x5
-				MX51_PAD_DI2_PIN2__DI2_PIN2		0x5
-				MX51_PAD_DI2_PIN3__DI2_PIN3		0x5
-				MX51_PAD_DI2_DISP_CLK__DI2_DISP_CLK	0x5
-				MX51_PAD_DI_GP4__DI2_PIN15		0x5
-			>;
-		};
+	pinctrl_ipu_disp2: ipudisp2grp {
+		fsl,pins = <
+			MX51_PAD_DISP2_DAT0__DISP2_DAT0		0x5
+			MX51_PAD_DISP2_DAT1__DISP2_DAT1		0x5
+			MX51_PAD_DISP2_DAT2__DISP2_DAT2		0x5
+			MX51_PAD_DISP2_DAT3__DISP2_DAT3		0x5
+			MX51_PAD_DISP2_DAT4__DISP2_DAT4		0x5
+			MX51_PAD_DISP2_DAT5__DISP2_DAT5		0x5
+			MX51_PAD_DISP2_DAT6__DISP2_DAT6		0x5
+			MX51_PAD_DISP2_DAT7__DISP2_DAT7		0x5
+			MX51_PAD_DISP2_DAT8__DISP2_DAT8		0x5
+			MX51_PAD_DISP2_DAT9__DISP2_DAT9		0x5
+			MX51_PAD_DISP2_DAT10__DISP2_DAT10	0x5
+			MX51_PAD_DISP2_DAT11__DISP2_DAT11	0x5
+			MX51_PAD_DISP2_DAT12__DISP2_DAT12	0x5
+			MX51_PAD_DISP2_DAT13__DISP2_DAT13	0x5
+			MX51_PAD_DISP2_DAT14__DISP2_DAT14	0x5
+			MX51_PAD_DISP2_DAT15__DISP2_DAT15	0x5
+			MX51_PAD_DI2_PIN2__DI2_PIN2		0x5
+			MX51_PAD_DI2_PIN3__DI2_PIN3		0x5
+			MX51_PAD_DI2_DISP_CLK__DI2_DISP_CLK	0x5
+			MX51_PAD_DI_GP4__DI2_PIN15		0x5
+		>;
+	};
 
-		pinctrl_kpp: kppgrp {
-			fsl,pins = <
-				MX51_PAD_KEY_ROW0__KEY_ROW0		0xe0
-				MX51_PAD_KEY_ROW1__KEY_ROW1		0xe0
-				MX51_PAD_KEY_ROW2__KEY_ROW2		0xe0
-				MX51_PAD_KEY_ROW3__KEY_ROW3		0xe0
-				MX51_PAD_KEY_COL0__KEY_COL0		0xe8
-				MX51_PAD_KEY_COL1__KEY_COL1		0xe8
-				MX51_PAD_KEY_COL2__KEY_COL2		0xe8
-				MX51_PAD_KEY_COL3__KEY_COL3		0xe8
-			>;
-		};
+	pinctrl_kpp: kppgrp {
+		fsl,pins = <
+			MX51_PAD_KEY_ROW0__KEY_ROW0		0xe0
+			MX51_PAD_KEY_ROW1__KEY_ROW1		0xe0
+			MX51_PAD_KEY_ROW2__KEY_ROW2		0xe0
+			MX51_PAD_KEY_ROW3__KEY_ROW3		0xe0
+			MX51_PAD_KEY_COL0__KEY_COL0		0xe8
+			MX51_PAD_KEY_COL1__KEY_COL1		0xe8
+			MX51_PAD_KEY_COL2__KEY_COL2		0xe8
+			MX51_PAD_KEY_COL3__KEY_COL3		0xe8
+		>;
+	};
 
-		pinctrl_pmic: pmicgrp {
-			fsl,pins = <
-				MX51_PAD_GPIO1_8__GPIO1_8		0xe5 /* IRQ */
-			>;
-		};
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			MX51_PAD_GPIO1_8__GPIO1_8		0xe5 /* IRQ */
+		>;
+	};
 
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX51_PAD_UART1_RXD__UART1_RXD		0x1c5
-				MX51_PAD_UART1_TXD__UART1_TXD		0x1c5
-				MX51_PAD_UART1_RTS__UART1_RTS		0x1c5
-				MX51_PAD_UART1_CTS__UART1_CTS		0x1c5
-			>;
-		};
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX51_PAD_UART1_RXD__UART1_RXD		0x1c5
+			MX51_PAD_UART1_TXD__UART1_TXD		0x1c5
+			MX51_PAD_UART1_RTS__UART1_RTS		0x1c5
+			MX51_PAD_UART1_CTS__UART1_CTS		0x1c5
+		>;
+	};
 
-		pinctrl_uart2: uart2grp {
-			fsl,pins = <
-				MX51_PAD_UART2_RXD__UART2_RXD		0x1c5
-				MX51_PAD_UART2_TXD__UART2_TXD		0x1c5
-			>;
-		};
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX51_PAD_UART2_RXD__UART2_RXD		0x1c5
+			MX51_PAD_UART2_TXD__UART2_TXD		0x1c5
+		>;
+	};
 
-		pinctrl_uart3: uart3grp {
-			fsl,pins = <
-				MX51_PAD_EIM_D25__UART3_RXD		0x1c5
-				MX51_PAD_EIM_D26__UART3_TXD		0x1c5
-				MX51_PAD_EIM_D27__UART3_RTS		0x1c5
-				MX51_PAD_EIM_D24__UART3_CTS		0x1c5
-			>;
-		};
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX51_PAD_EIM_D25__UART3_RXD		0x1c5
+			MX51_PAD_EIM_D26__UART3_TXD		0x1c5
+			MX51_PAD_EIM_D27__UART3_RTS		0x1c5
+			MX51_PAD_EIM_D24__UART3_CTS		0x1c5
+		>;
+	};
 
-		pinctrl_usbh1: usbh1grp {
-			fsl,pins = <
-				MX51_PAD_USBH1_CLK__USBH1_CLK		0x80000000
-				MX51_PAD_USBH1_DIR__USBH1_DIR		0x80000000
-				MX51_PAD_USBH1_NXT__USBH1_NXT		0x80000000
-				MX51_PAD_USBH1_DATA0__USBH1_DATA0	0x80000000
-				MX51_PAD_USBH1_DATA1__USBH1_DATA1	0x80000000
-				MX51_PAD_USBH1_DATA2__USBH1_DATA2	0x80000000
-				MX51_PAD_USBH1_DATA3__USBH1_DATA3	0x80000000
-				MX51_PAD_USBH1_DATA4__USBH1_DATA4	0x80000000
-				MX51_PAD_USBH1_DATA5__USBH1_DATA5	0x80000000
-				MX51_PAD_USBH1_DATA6__USBH1_DATA6	0x80000000
-				MX51_PAD_USBH1_DATA7__USBH1_DATA7	0x80000000
-			>;
-		};
+	pinctrl_usbh1: usbh1grp {
+		fsl,pins = <
+			MX51_PAD_USBH1_CLK__USBH1_CLK		0x80000000
+			MX51_PAD_USBH1_DIR__USBH1_DIR		0x80000000
+			MX51_PAD_USBH1_NXT__USBH1_NXT		0x80000000
+			MX51_PAD_USBH1_DATA0__USBH1_DATA0	0x80000000
+			MX51_PAD_USBH1_DATA1__USBH1_DATA1	0x80000000
+			MX51_PAD_USBH1_DATA2__USBH1_DATA2	0x80000000
+			MX51_PAD_USBH1_DATA3__USBH1_DATA3	0x80000000
+			MX51_PAD_USBH1_DATA4__USBH1_DATA4	0x80000000
+			MX51_PAD_USBH1_DATA5__USBH1_DATA5	0x80000000
+			MX51_PAD_USBH1_DATA6__USBH1_DATA6	0x80000000
+			MX51_PAD_USBH1_DATA7__USBH1_DATA7	0x80000000
+		>;
+	};
 
-		pinctrl_usbh1reg: usbh1reggrp {
-			fsl,pins = <
-				MX51_PAD_EIM_D21__GPIO2_5		0x85
-			>;
-		};
+	pinctrl_usbh1reg: usbh1reggrp {
+		fsl,pins = <
+			MX51_PAD_EIM_D21__GPIO2_5		0x85
+		>;
+	};
 
-		pinctrl_usbotgreg: usbotgreggrp {
-			fsl,pins = <
-				MX51_PAD_GPIO1_7__GPIO1_7		0x85
-			>;
-		};
+	pinctrl_usbotgreg: usbotgreggrp {
+		fsl,pins = <
+			MX51_PAD_GPIO1_7__GPIO1_7		0x85
+		>;
 	};
 };
diff --git a/arch/arm/boot/dts/nxp/imx/imx51-digi-connectcore-jsk.dts b/arch/arm/boot/dts/nxp/imx/imx51-digi-connectcore-jsk.dts
new file mode 100644
index 000000000000..9750b5f93330
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx51-digi-connectcore-jsk.dts
@@ -0,0 +1,124 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2014 Alexander Shiyan <shc_work@mail.ru>
+ */
+
+#include "imx51-digi-connectcore-som.dtsi"
+
+/ {
+	model = "Digi ConnectCore CC(W)-MX51 JSK";
+	compatible = "digi,connectcore-ccxmx51-jsk",
+		     "digi,connectcore-ccxmx51-som", "fsl,imx51";
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	usbphy1: usbphy1 {
+		compatible = "usb-nop-xceiv";
+		clocks = <&clks IMX5_CLK_USB_PHY_GATE>;
+		clock-names = "main_clk";
+		#phy-cells = <0>;
+	};
+};
+
+&esdhc1 {
+	status = "okay";
+};
+
+&owire {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_owire>;
+	status = "okay";
+};
+
+&pmic {
+	fsl,mc13xxx-uses-rtc;
+
+	regulators {
+		vcoincell_reg: vcoincell {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-always-on;
+		};
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&usbotg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbh1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbh1>;
+	fsl,usbphy = <&usbphy1>;
+	dr_mode = "host";
+	phy_type = "ulpi";
+	disable-over-current;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_owire: owiregrp {
+		fsl,pins = <
+			MX51_PAD_OWIRE_LINE__OWIRE_LINE		0x40000000
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX51_PAD_UART1_RXD__UART1_RXD		0x1c5
+			MX51_PAD_UART1_TXD__UART1_TXD		0x1c5
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX51_PAD_UART2_RXD__UART2_RXD		0x1c5
+			MX51_PAD_UART2_TXD__UART2_TXD		0x1c5
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX51_PAD_UART3_RXD__UART3_RXD		0x1c5
+			MX51_PAD_UART3_TXD__UART3_TXD		0x1c5
+		>;
+	};
+
+	pinctrl_usbh1: usbh1grp {
+		fsl,pins = <
+			MX51_PAD_USBH1_DATA0__USBH1_DATA0	0x1e5
+			MX51_PAD_USBH1_DATA1__USBH1_DATA1	0x1e5
+			MX51_PAD_USBH1_DATA2__USBH1_DATA2	0x1e5
+			MX51_PAD_USBH1_DATA3__USBH1_DATA3	0x1e5
+			MX51_PAD_USBH1_DATA4__USBH1_DATA4	0x1e5
+			MX51_PAD_USBH1_DATA5__USBH1_DATA5	0x1e5
+			MX51_PAD_USBH1_DATA6__USBH1_DATA6	0x1e5
+			MX51_PAD_USBH1_DATA7__USBH1_DATA7	0x1e5
+			MX51_PAD_USBH1_CLK__USBH1_CLK		0x1e5
+			MX51_PAD_USBH1_DIR__USBH1_DIR		0x1e5
+			MX51_PAD_USBH1_NXT__USBH1_NXT		0x1e5
+			MX51_PAD_USBH1_STP__USBH1_STP		0x1e5
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx51-digi-connectcore-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx51-digi-connectcore-som.dtsi
new file mode 100644
index 000000000000..1980f751f161
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx51-digi-connectcore-som.dtsi
@@ -0,0 +1,374 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2014 Alexander Shiyan <shc_work@mail.ru>
+ */
+
+/dts-v1/;
+#include "imx51.dtsi"
+
+/ {
+	model = "Digi ConnectCore CC(W)-MX51";
+	compatible = "digi,connectcore-ccxmx51-som", "fsl,imx51";
+
+	memory@90000000 {
+		device_type = "memory";
+		reg = <0x90000000 0x08000000>;
+	};
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+
+	pmic: mc13892@0 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_mc13892>;
+		compatible = "fsl,mc13892";
+		spi-max-frequency = <16000000>;
+		spi-cs-high;
+		reg = <0>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+
+		regulators {
+			sw1_reg: sw1 {
+				regulator-min-microvolt = <1050000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <1175000>;
+				regulator-max-microvolt = <1275000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3_reg: sw3 {
+				regulator-min-microvolt = <1150000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			swbst_reg: swbst { };
+
+			viohi_reg: viohi {
+				regulator-always-on;
+			};
+
+			vpll_reg: vpll {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			vdig_reg: vdig {
+				regulator-min-microvolt = <1250000>;
+				regulator-max-microvolt = <1250000>;
+				regulator-always-on;
+			};
+
+			vsd_reg: vsd {
+				regulator-min-microvolt = <3150000>;
+				regulator-max-microvolt = <3150000>;
+				regulator-always-on;
+			};
+
+			vusb2_reg: vusb2 {
+				regulator-min-microvolt = <2600000>;
+				regulator-max-microvolt = <2600000>;
+				regulator-always-on;
+			};
+
+			vvideo_reg: vvideo {
+				regulator-min-microvolt = <2775000>;
+				regulator-max-microvolt = <2775000>;
+				regulator-always-on;
+			};
+
+			vaudio_reg: vaudio {
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-always-on;
+			};
+
+			vcam_reg: vcam {
+				regulator-min-microvolt = <2750000>;
+				regulator-max-microvolt = <2750000>;
+				regulator-always-on;
+			};
+
+			vgen3_reg: vgen3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			vusb_reg: vusb {
+				regulator-always-on;
+			};
+
+			gpo2_reg: gpo2 { };
+
+			gpo3_reg: gpo3 { };
+
+			gpo4_reg: gpo4 { };
+
+			pwgt2spi_reg: pwgt2spi {
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&esdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc1>;
+	max-frequency = <50000000>;
+	bus-width = <1>;
+};
+
+&esdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc2>;
+	cap-sdio-irq;
+	wakeup-source;
+	keep-power-in-suspend;
+	max-frequency = <50000000>;
+	no-1-8-v;
+	non-removable;
+	vmmc-supply = <&gpo4_reg>;
+	status = "okay";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec>;
+	phy-mode = "mii";
+	phy-supply = <&gpo3_reg>;
+	/* Pins shared with LCD2, keep status disabled */
+};
+
+&i2c2 {
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	clock-frequency = <400000>;
+	scl-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+
+	mma7455l@1d {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_mma7455l>;
+		compatible = "fsl,mma7455";
+		reg = <0x1d>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <7 IRQ_TYPE_LEVEL_HIGH>, <6 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
+
+&nfc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_nfc>;
+	nand-bus-width = <8>;
+	nand-ecc-mode = "hw";
+	nand-on-flash-bbt;
+	status = "okay";
+};
+
+&usbotg {
+	phy_type = "utmi_wide";
+	disable-over-current;
+	vbus-supply = <&swbst_reg>;
+	/* Device role is not known, keep status disabled */
+};
+
+&weim {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_weim>;
+	status = "okay";
+
+	lan9221: ethernet@5,0 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lan9221>;
+		compatible = "smsc,lan9221", "smsc,lan9115";
+		reg = <5 0x00000000 0x1000>;
+		fsl,weim-cs-timing = <
+			0x00420081 0x00000000
+			0x32260000 0x00000000
+			0x72080f00 0x00000000
+		>;
+		clocks = <&clks IMX5_CLK_DUMMY>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+		phy-mode = "mii";
+		reg-io-width = <2>;
+		smsc,irq-push-pull;
+		vdd33a-supply = <&gpo2_reg>;
+		vddvario-supply = <&gpo2_reg>;
+	};
+};
+
+&iomuxc {
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX51_PAD_CSPI1_MISO__ECSPI1_MISO	0x185
+			MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI	0x185
+			MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK	0x185
+			MX51_PAD_CSPI1_SS0__GPIO4_24		0x85 /* CS0 */
+		>;
+	};
+
+	pinctrl_esdhc1: esdhc1grp {
+		fsl,pins = <
+			MX51_PAD_SD1_CLK__SD1_CLK		0x400021d5
+			MX51_PAD_SD1_CMD__SD1_CMD		0x400020d5
+			MX51_PAD_SD1_DATA0__SD1_DATA0		0x400020d5
+		>;
+	};
+
+	pinctrl_esdhc2: esdhc2grp {
+		fsl,pins = <
+			MX51_PAD_SD2_CMD__SD2_CMD		0x400020d5
+			MX51_PAD_SD2_CLK__SD2_CLK		0x20d5
+			MX51_PAD_SD2_DATA0__SD2_DATA0		0x20d5
+			MX51_PAD_SD2_DATA1__SD2_DATA1		0x20d5
+			MX51_PAD_SD2_DATA2__SD2_DATA2		0x20d5
+			MX51_PAD_SD2_DATA3__SD2_DATA3		0x20d5
+		>;
+	};
+
+	pinctrl_fec: fecgrp {
+		fsl,pins = <
+			MX51_PAD_DI_GP3__FEC_TX_ER		0x80000000
+			MX51_PAD_DI2_PIN4__FEC_CRS		0x80000000
+			MX51_PAD_DI2_PIN2__FEC_MDC		0x80000000
+			MX51_PAD_DI2_PIN3__FEC_MDIO		0x80000000
+			MX51_PAD_DI2_DISP_CLK__FEC_RDATA1	0x80000000
+			MX51_PAD_DI_GP4__FEC_RDATA2		0x80000000
+			MX51_PAD_DISP2_DAT0__FEC_RDATA3		0x80000000
+			MX51_PAD_DISP2_DAT1__FEC_RX_ER		0x80000000
+			MX51_PAD_DISP2_DAT6__FEC_TDATA1		0x80000000
+			MX51_PAD_DISP2_DAT7__FEC_TDATA2		0x80000000
+			MX51_PAD_DISP2_DAT8__FEC_TDATA3		0x80000000
+			MX51_PAD_DISP2_DAT9__FEC_TX_EN		0x80000000
+			MX51_PAD_DISP2_DAT10__FEC_COL		0x80000000
+			MX51_PAD_DISP2_DAT11__FEC_RX_CLK	0x80000000
+			MX51_PAD_DISP2_DAT12__FEC_RX_DV		0x80000000
+			MX51_PAD_DISP2_DAT13__FEC_TX_CLK	0x80000000
+			MX51_PAD_DISP2_DAT14__FEC_RDATA0	0x80000000
+			MX51_PAD_DISP2_DAT15__FEC_TDATA0	0x80000000
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX51_PAD_GPIO1_2__I2C2_SCL		0x400001ed
+			MX51_PAD_GPIO1_3__I2C2_SDA		0x400001ed
+		>;
+	};
+
+	pinctrl_i2c2_gpio: i2c2gpiogrp {
+		fsl,pins = <
+			MX51_PAD_GPIO1_2__GPIO1_2		0x400001ed
+			MX51_PAD_GPIO1_3__GPIO1_3		0x400001ed
+		>;
+	};
+
+	pinctrl_nfc: nfcgrp {
+		fsl,pins = <
+			MX51_PAD_NANDF_D0__NANDF_D0		0x80000000
+			MX51_PAD_NANDF_D1__NANDF_D1		0x80000000
+			MX51_PAD_NANDF_D2__NANDF_D2		0x80000000
+			MX51_PAD_NANDF_D3__NANDF_D3		0x80000000
+			MX51_PAD_NANDF_D4__NANDF_D4		0x80000000
+			MX51_PAD_NANDF_D5__NANDF_D5		0x80000000
+			MX51_PAD_NANDF_D6__NANDF_D6		0x80000000
+			MX51_PAD_NANDF_D7__NANDF_D7		0x80000000
+			MX51_PAD_NANDF_ALE__NANDF_ALE		0x80000000
+			MX51_PAD_NANDF_CLE__NANDF_CLE		0x80000000
+			MX51_PAD_NANDF_RE_B__NANDF_RE_B		0x80000000
+			MX51_PAD_NANDF_WE_B__NANDF_WE_B		0x80000000
+			MX51_PAD_NANDF_WP_B__NANDF_WP_B		0x80000000
+			MX51_PAD_NANDF_CS0__NANDF_CS0		0x80000000
+			MX51_PAD_NANDF_RB0__NANDF_RB0		0x80000000
+		>;
+	};
+
+	pinctrl_lan9221: lan9221grp {
+		fsl,pins = <
+			MX51_PAD_GPIO1_9__GPIO1_9		0xe5 /* IRQ */
+		>;
+	};
+
+	pinctrl_mc13892: mc13892grp {
+		fsl,pins = <
+			MX51_PAD_GPIO1_5__GPIO1_5		0xe5 /* IRQ */
+		>;
+	};
+
+	pinctrl_mma7455l: mma7455lgrp {
+		fsl,pins = <
+			MX51_PAD_GPIO1_7__GPIO1_7		0xe5 /* IRQ1 */
+			MX51_PAD_GPIO1_6__GPIO1_6		0xe5 /* IRQ2 */
+		>;
+	};
+
+	pinctrl_weim: weimgrp {
+		fsl,pins = <
+			MX51_PAD_EIM_DA0__EIM_DA0		0x80000000
+			MX51_PAD_EIM_DA1__EIM_DA1		0x80000000
+			MX51_PAD_EIM_DA2__EIM_DA2		0x80000000
+			MX51_PAD_EIM_DA3__EIM_DA3		0x80000000
+			MX51_PAD_EIM_DA4__EIM_DA4		0x80000000
+			MX51_PAD_EIM_DA5__EIM_DA5		0x80000000
+			MX51_PAD_EIM_DA6__EIM_DA6		0x80000000
+			MX51_PAD_EIM_DA7__EIM_DA7		0x80000000
+			MX51_PAD_EIM_DA8__EIM_DA8		0x80000000
+			MX51_PAD_EIM_DA9__EIM_DA9		0x80000000
+			MX51_PAD_EIM_DA10__EIM_DA10		0x80000000
+			MX51_PAD_EIM_DA11__EIM_DA11		0x80000000
+			MX51_PAD_EIM_DA12__EIM_DA12		0x80000000
+			MX51_PAD_EIM_DA13__EIM_DA13		0x80000000
+			MX51_PAD_EIM_DA14__EIM_DA14		0x80000000
+			MX51_PAD_EIM_DA15__EIM_DA15		0x80000000
+			MX51_PAD_EIM_A16__EIM_A16		0x80000000
+			MX51_PAD_EIM_A17__EIM_A17		0x80000000
+			MX51_PAD_EIM_A18__EIM_A18		0x80000000
+			MX51_PAD_EIM_A19__EIM_A19		0x80000000
+			MX51_PAD_EIM_A20__EIM_A20		0x80000000
+			MX51_PAD_EIM_A21__EIM_A21		0x80000000
+			MX51_PAD_EIM_A22__EIM_A22		0x80000000
+			MX51_PAD_EIM_A23__EIM_A23		0x80000000
+			MX51_PAD_EIM_A24__EIM_A24		0x80000000
+			MX51_PAD_EIM_A25__EIM_A25		0x80000000
+			MX51_PAD_EIM_A26__EIM_A26		0x80000000
+			MX51_PAD_EIM_A27__EIM_A27		0x80000000
+			MX51_PAD_EIM_D16__EIM_D16		0x80000000
+			MX51_PAD_EIM_D17__EIM_D17		0x80000000
+			MX51_PAD_EIM_D18__EIM_D18		0x80000000
+			MX51_PAD_EIM_D19__EIM_D19		0x80000000
+			MX51_PAD_EIM_D20__EIM_D20		0x80000000
+			MX51_PAD_EIM_D21__EIM_D21		0x80000000
+			MX51_PAD_EIM_D22__EIM_D22		0x80000000
+			MX51_PAD_EIM_D23__EIM_D23		0x80000000
+			MX51_PAD_EIM_D24__EIM_D24		0x80000000
+			MX51_PAD_EIM_D25__EIM_D25		0x80000000
+			MX51_PAD_EIM_D26__EIM_D26		0x80000000
+			MX51_PAD_EIM_D27__EIM_D27		0x80000000
+			MX51_PAD_EIM_D28__EIM_D28		0x80000000
+			MX51_PAD_EIM_D29__EIM_D29		0x80000000
+			MX51_PAD_EIM_D30__EIM_D30		0x80000000
+			MX51_PAD_EIM_D31__EIM_D31		0x80000000
+			MX51_PAD_EIM_OE__EIM_OE			0x80000000
+			MX51_PAD_EIM_DTACK__EIM_DTACK		0x80000000
+			MX51_PAD_EIM_LBA__EIM_LBA		0x80000000
+			MX51_PAD_EIM_CS5__EIM_CS5		0x80000000 /* CS5 */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx51-eukrea-cpuimx51.dtsi b/arch/arm/boot/dts/nxp/imx/imx51-eukrea-cpuimx51.dtsi
new file mode 100644
index 000000000000..244740d65b3d
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx51-eukrea-cpuimx51.dtsi
@@ -0,0 +1,90 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Eukréa Electromatique <denis@eukrea.com>
+ */
+
+#include "imx51.dtsi"
+
+/ {
+	model = "Eukrea CPUIMX51";
+	compatible = "eukrea,cpuimx51", "fsl,imx51";
+
+	memory@90000000 {
+		device_type = "memory";
+		reg = <0x90000000 0x10000000>; /* 256M */
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+
+	tsc2007: tsc2007@49 {
+		compatible = "ti,tsc2007";
+		gpios = <&gpio4 0 1>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <0x0 0x8>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tsc2007_1>;
+		reg = <0x49>;
+		ti,x-plate-ohms = <180>;
+	};
+};
+
+&iomuxc {
+	pinctrl_tsc2007_1: tsc2007-1-grp {
+		fsl,pins = <
+			MX51_PAD_GPIO_NAND__GPIO_NAND 0x1f5
+			MX51_PAD_NANDF_D8__GPIO4_0 0x1f5
+		>;
+	};
+
+	pinctrl_fec: fecgrp {
+		fsl,pins = <
+			MX51_PAD_DI_GP3__FEC_TX_ER		0x80000000
+			MX51_PAD_DI2_PIN4__FEC_CRS		0x80000000
+			MX51_PAD_DI2_PIN2__FEC_MDC		0x80000000
+			MX51_PAD_DI2_PIN3__FEC_MDIO		0x80000000
+			MX51_PAD_DI2_DISP_CLK__FEC_RDATA1	0x80000000
+			MX51_PAD_DI_GP4__FEC_RDATA2		0x80000000
+			MX51_PAD_DISP2_DAT0__FEC_RDATA3		0x80000000
+			MX51_PAD_DISP2_DAT1__FEC_RX_ER		0x80000000
+			MX51_PAD_DISP2_DAT6__FEC_TDATA1		0x80000000
+			MX51_PAD_DISP2_DAT7__FEC_TDATA2		0x80000000
+			MX51_PAD_DISP2_DAT8__FEC_TDATA3		0x80000000
+			MX51_PAD_DISP2_DAT9__FEC_TX_EN		0x80000000
+			MX51_PAD_DISP2_DAT10__FEC_COL		0x80000000
+			MX51_PAD_DISP2_DAT11__FEC_RX_CLK	0x80000000
+			MX51_PAD_DISP2_DAT12__FEC_RX_DV		0x80000000
+			MX51_PAD_DISP2_DAT13__FEC_TX_CLK	0x80000000
+			MX51_PAD_DISP2_DAT14__FEC_RDATA0	0x80000000
+			MX51_PAD_DISP2_DAT15__FEC_TDATA0	0x80000000
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX51_PAD_SD2_CMD__I2C1_SCL		0x400001ed
+			MX51_PAD_SD2_CLK__I2C1_SDA		0x400001ed
+		>;
+	};
+};
+
+&nfc {
+	nand-bus-width = <8>;
+	nand-ecc-mode = "hw";
+	nand-on-flash-bbt;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx51-eukrea-mbimxsd51-baseboard.dts b/arch/arm/boot/dts/nxp/imx/imx51-eukrea-mbimxsd51-baseboard.dts
new file mode 100644
index 000000000000..0e0b9a811b96
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx51-eukrea-mbimxsd51-baseboard.dts
@@ -0,0 +1,265 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Eukréa Electromatique <denis@eukrea.com>
+ */
+
+/dts-v1/;
+#include "imx51-eukrea-cpuimx51.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Eukrea CPUIMX51";
+	compatible = "eukrea,mbimxsd51","eukrea,cpuimx51", "fsl,imx51";
+
+	clocks {
+		clk24M: can_clock {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <24000000>;
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpiokeys_1>;
+
+		button-1 {
+			label = "BP1";
+			gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;
+			linux,code = <256>;
+			wakeup-source;
+			linux,input-type = <1>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpioled>;
+
+		led1 {
+			label = "led1";
+			gpios = <&gpio3 30 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	reg_can: regulator-can {
+		compatible = "regulator-fixed";
+		regulator-name = "CAN_RST";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <20000>;
+		enable-active-high;
+	};
+
+	sound {
+		compatible = "eukrea,asoc-tlv320";
+		eukrea,model = "imx51-eukrea-tlv320aic23";
+		ssi-controller = <&ssi2>;
+		fsl,mux-int-port = <2>;
+		fsl,mux-ext-port = <3>;
+	};
+
+	usbphy1: usbphy1 {
+		compatible = "usb-nop-xceiv";
+		clocks = <&clks IMX5_CLK_USB_PHY_GATE>;
+		clock-names = "main_clk";
+		clock-frequency = <19200000>;
+		#phy-cells = <0>;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+};
+
+&esdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc1 &pinctrl_esdhc1_cd>;
+	cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	can0: can@0 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can>;
+		compatible = "microchip,mcp2515";
+		reg = <0>;
+		clocks = <&clk24M>;
+		spi-max-frequency = <10000000>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&reg_can>;
+	};
+};
+
+&i2c1 {
+	tlv320aic23: codec@1a {
+		compatible = "ti,tlv320aic23";
+		reg = <0x1a>;
+	};
+};
+
+&iomuxc {
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX51_PAD_AUD3_BB_TXD__AUD3_TXD		0x80000000
+			MX51_PAD_AUD3_BB_RXD__AUD3_RXD		0x80000000
+			MX51_PAD_AUD3_BB_CK__AUD3_TXC		0x80000000
+			MX51_PAD_AUD3_BB_FS__AUD3_TXFS		0x80000000
+		>;
+	};
+
+
+	pinctrl_can: cangrp {
+		fsl,pins = <
+			MX51_PAD_CSI2_PIXCLK__GPIO4_15		0x80000000	/* nReset */
+			MX51_PAD_GPIO1_1__GPIO1_1		0x80000000	/* IRQ */
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX51_PAD_CSPI1_MISO__ECSPI1_MISO	0x185
+			MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI	0x185
+			MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK	0x185
+			MX51_PAD_CSPI1_SS0__GPIO4_24		0x80000000 	/* CS0 */
+		>;
+	};
+
+	pinctrl_esdhc1: esdhc1grp {
+		fsl,pins = <
+			MX51_PAD_SD1_CMD__SD1_CMD		0x400020d5
+			MX51_PAD_SD1_CLK__SD1_CLK		0x20d5
+			MX51_PAD_SD1_DATA0__SD1_DATA0		0x20d5
+			MX51_PAD_SD1_DATA1__SD1_DATA1		0x20d5
+			MX51_PAD_SD1_DATA2__SD1_DATA2		0x20d5
+			MX51_PAD_SD1_DATA3__SD1_DATA3		0x20d5
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX51_PAD_UART1_RXD__UART1_RXD		0x1c5
+			MX51_PAD_UART1_TXD__UART1_TXD		0x1c5
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX51_PAD_UART3_RXD__UART3_RXD		0x1c5
+			MX51_PAD_UART3_TXD__UART3_TXD		0x1c5
+		>;
+	};
+
+	pinctrl_uart3_rtscts: uart3rtsctsgrp {
+		fsl,pins = <
+			MX51_PAD_KEY_COL4__UART3_RTS		0x1c5
+			MX51_PAD_KEY_COL5__UART3_CTS		0x1c5
+		>;
+	};
+
+	pinctrl_backlight_1: backlight1grp {
+		fsl,pins = <
+			MX51_PAD_DI1_D1_CS__GPIO3_4 0x1f5
+		>;
+	};
+
+	pinctrl_esdhc1_cd: esdhc1_cdgrp {
+		fsl,pins = <
+			MX51_PAD_GPIO1_0__GPIO1_0 0xd5
+		>;
+	};
+
+	pinctrl_gpiokeys_1: gpiokeys1grp {
+		fsl,pins = <
+			MX51_PAD_NANDF_D9__GPIO3_31 0x1f5
+		>;
+	};
+
+	pinctrl_gpioled: gpioled1grp {
+		fsl,pins = <
+			MX51_PAD_NANDF_D10__GPIO3_30 0x80000000
+		>;
+	};
+
+	pinctrl_reg_lcd_3v3: reg_lcd_3v3grp {
+		fsl,pins = <
+			MX51_PAD_CSI1_D9__GPIO3_13 0x1f5
+		>;
+	};
+
+	pinctrl_usbh1: usbh1grp {
+		fsl,pins = <
+			MX51_PAD_USBH1_CLK__USBH1_CLK     0x1e5
+			MX51_PAD_USBH1_DIR__USBH1_DIR     0x1e5
+			MX51_PAD_USBH1_NXT__USBH1_NXT     0x1e5
+			MX51_PAD_USBH1_DATA0__USBH1_DATA0 0x1e5
+			MX51_PAD_USBH1_DATA1__USBH1_DATA1 0x1e5
+			MX51_PAD_USBH1_DATA2__USBH1_DATA2 0x1e5
+			MX51_PAD_USBH1_DATA3__USBH1_DATA3 0x1e5
+			MX51_PAD_USBH1_DATA4__USBH1_DATA4 0x1e5
+			MX51_PAD_USBH1_DATA5__USBH1_DATA5 0x1e5
+			MX51_PAD_USBH1_DATA6__USBH1_DATA6 0x1e5
+			MX51_PAD_USBH1_DATA7__USBH1_DATA7 0x1e5
+			MX51_PAD_USBH1_STP__USBH1_STP     0x1e5
+		>;
+	};
+
+	pinctrl_usbh1_vbus: usbh1-vbusgrp {
+		fsl,pins = <
+			MX51_PAD_EIM_CS3__GPIO2_28 0x1f5
+		>;
+	};
+};
+
+&ssi2 {
+	codec-handle = <&tlv320aic23>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3 &pinctrl_uart3_rtscts>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbh1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbh1>;
+	fsl,usbphy = <&usbphy1>;
+	dr_mode = "host";
+	phy_type = "ulpi";
+	status = "okay";
+};
+
+&usbotg {
+	dr_mode = "otg";
+	phy_type = "utmi_wide";
+	status = "okay";
+};
+
+&usbphy0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbh1_vbus>;
+	reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+};
diff --git a/arch/arm/boot/dts/imx51-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx51-pinfunc.h
index 910e0ec50ef3..910e0ec50ef3 100644
--- a/arch/arm/boot/dts/imx51-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx51-pinfunc.h
diff --git a/arch/arm/boot/dts/imx51-ts4800.dts b/arch/arm/boot/dts/nxp/imx/imx51-ts4800.dts
index 85654d6baf28..079bd3d14999 100644
--- a/arch/arm/boot/dts/imx51-ts4800.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx51-ts4800.dts
@@ -45,7 +45,7 @@
 
 	backlight: backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 78770>;
+		pwms = <&pwm1 0 78770 0>;
 		brightness-levels = <0 150 200 255>;
 		default-brightness-level = <1>;
 		power-supply = <&backlight_reg>;
@@ -58,8 +58,8 @@
 		pinctrl-0 = <&pinctrl_lcd>;
 
 		display-timings {
-			800x480p60 {
-				native-mode;
+			native-mode = <&timing0>;
+			timing0: timing-800x480p60 {
 				clock-frequency = <30066000>;
 				hactive = <800>;
 				vactive = <480>;
@@ -113,7 +113,6 @@
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm_backlight>;
 	status = "okay";
@@ -174,7 +173,7 @@
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_interrupt_fpga>;
 			interrupt-parent = <&gpio2>;
-			interrupts= <9 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <9 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <1>;
 		};
diff --git a/arch/arm/boot/dts/imx51-zii-rdu1.dts b/arch/arm/boot/dts/nxp/imx/imx51-zii-rdu1.dts
index ec8ca3ac2c1c..06545a6052f7 100644
--- a/arch/arm/boot/dts/imx51-zii-rdu1.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx51-zii-rdu1.dts
@@ -119,8 +119,8 @@
 		compatible = "i2c-gpio";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_swi2c>;
-		gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>, /* sda */
-			<&gpio3 4 GPIO_ACTIVE_HIGH>; /* scl */
+		sda-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+		scl-gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>;
 		i2c-gpio,delay-us = <50>;
 		status = "okay";
 
@@ -137,7 +137,7 @@
 		};
 	};
 
-	spi_gpio: spi-gpio {
+	spi_gpio: spi {
 		compatible = "spi-gpio";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -145,9 +145,9 @@
 		pinctrl-0 = <&pinctrl_gpiospi0>;
 		status = "okay";
 
-		gpio-sck = <&gpio4 15 GPIO_ACTIVE_HIGH>;
-		gpio-mosi = <&gpio4 12 GPIO_ACTIVE_HIGH>;
-		gpio-miso = <&gpio4 11 GPIO_ACTIVE_HIGH>;
+		sck-gpios = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpio4 11 GPIO_ACTIVE_HIGH>;
 		num-chipselects = <1>;
 		cs-gpios = <&gpio4 14 GPIO_ACTIVE_HIGH>;
 
@@ -160,7 +160,7 @@
 		};
 	};
 
-	mdio_gpio: mdio-gpio {
+	mdio_gpio: mdio {
 		compatible = "virtual,mdio-gpio";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_swmdio>;
@@ -181,7 +181,7 @@
 
 				port@0 {
 					reg = <0>;
-					label = "cpu";
+					phy-mode = "rev-mii";
 					ethernet = <&fec>;
 
 					fixed-link {
@@ -556,7 +556,7 @@
 	pinctrl-0 = <&pinctrl_uart3>;
 	status = "okay";
 
-	rave-sp {
+	mcu {
 		compatible = "zii,rave-sp-rdu1";
 		current-speed = <38400>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/imx51-zii-scu2-mezz.dts b/arch/arm/boot/dts/nxp/imx/imx51-zii-scu2-mezz.dts
index aa91e5dde4b8..26eb7a9506e4 100644
--- a/arch/arm/boot/dts/imx51-zii-scu2-mezz.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx51-zii-scu2-mezz.dts
@@ -37,7 +37,7 @@
 		regulator-max-microvolt = <5000000>;
 	};
 
-	mdio_gpio: mdio-gpio {
+	mdio_gpio: mdio {
 		compatible = "virtual,mdio-gpio";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_swmdio>;
@@ -82,7 +82,7 @@
 
 				port@4 {
 					reg = <4>;
-					label = "cpu";
+					phy-mode = "rev-mii";
 					ethernet = <&fec>;
 
 					fixed-link {
@@ -311,7 +311,7 @@
 	pinctrl-0 = <&pinctrl_uart3>;
 	status = "okay";
 
-	rave-sp {
+	mcu {
 		compatible = "zii,rave-sp-mezz";
 		current-speed = <57600>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/imx51-zii-scu3-esb.dts b/arch/arm/boot/dts/nxp/imx/imx51-zii-scu3-esb.dts
index 875b10a7d674..19a3b142c964 100644
--- a/arch/arm/boot/dts/imx51-zii-scu3-esb.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx51-zii-scu3-esb.dts
@@ -267,7 +267,6 @@
 
 				port@6 {
 					reg = <6>;
-					label = "cpu";
 					phy-mode = "mii";
 					ethernet = <&fec>;
 
@@ -319,7 +318,7 @@
 	pinctrl-0 = <&pinctrl_uart3>;
 	status = "okay";
 
-	rave-sp {
+	mcu {
 		compatible = "zii,rave-sp-esb";
 		current-speed = <57600>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/imx51.dtsi b/arch/arm/boot/dts/nxp/imx/imx51.dtsi
index 56c8d87864c3..c8698a9af1a7 100644
--- a/arch/arm/boot/dts/imx51.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx51.dtsi
@@ -114,7 +114,7 @@
 		ports = <&ipu_di0>, <&ipu_di1>;
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
@@ -124,6 +124,9 @@
 		iram: sram@1ffe0000 {
 			compatible = "mmio-sram";
 			reg = <0x1ffe0000 0x20000>;
+			ranges = <0 0x1ffe0000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 		};
 
 		gpu: gpu@30000000 {
@@ -171,7 +174,7 @@
 			};
 		};
 
-		bus@70000000 { /* AIPS1 */
+		aips1: bus@70000000 { /* AIPS1 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -215,6 +218,8 @@
 					clocks = <&clks IMX5_CLK_UART3_IPG_GATE>,
 						 <&clks IMX5_CLK_UART3_PER_GATE>;
 					clock-names = "ipg", "per";
+					dmas = <&sdma 43 5 1>, <&sdma 44 5 2>;
+					dma-names = "rx", "tx";
 					status = "disabled";
 				};
 
@@ -394,7 +399,7 @@
 				clock-names = "ipg", "per";
 			};
 
-			iomuxc: iomuxc@73fa8000 {
+			iomuxc: pinctrl@73fa8000 {
 				compatible = "fsl,imx51-iomuxc";
 				reg = <0x73fa8000 0x4000>;
 			};
@@ -426,6 +431,8 @@
 				clocks = <&clks IMX5_CLK_UART1_IPG_GATE>,
 					 <&clks IMX5_CLK_UART1_PER_GATE>;
 				clock-names = "ipg", "per";
+				dmas = <&sdma 18 4 1>, <&sdma 19 4 2>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 
@@ -436,6 +443,8 @@
 				clocks = <&clks IMX5_CLK_UART2_IPG_GATE>,
 					 <&clks IMX5_CLK_UART2_PER_GATE>;
 				clock-names = "ipg", "per";
+				dmas = <&sdma 16 4 1>, <&sdma 17 4 2>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 
@@ -446,15 +455,15 @@
 				#reset-cells = <1>;
 			};
 
-			clks: ccm@73fd4000{
+			clks: ccm@73fd4000 {
 				compatible = "fsl,imx51-ccm";
 				reg = <0x73fd4000 0x4000>;
-				interrupts = <0 71 0x04 0 72 0x04>;
+				interrupts = <71>, <72>;
 				#clock-cells = <1>;
 			};
 		};
 
-		bus@80000000 {	/* AIPS2 */
+		aips2: bus@80000000 {	/* AIPS2 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -467,7 +476,7 @@
 			};
 
 			iim: efuse@83f98000 {
-				compatible = "fsl,imx51-iim", "fsl,imx27-iim", "syscon";
+				compatible = "fsl,imx51-iim";
 				reg = <0x83f98000 0x4000>;
 				interrupts = <69>;
 				clocks = <&clks IMX5_CLK_IIM_GATE>;
@@ -498,7 +507,7 @@
 				status = "disabled";
 			};
 
-			sdma: sdma@83fb0000 {
+			sdma: dma-controller@83fb0000 {
 				compatible = "fsl,imx51-sdma", "fsl,imx35-sdma";
 				reg = <0x83fb0000 0x4000>;
 				interrupts = <6>;
@@ -569,7 +578,7 @@
 				reg = <0x83fd8000 0x1000>;
 			};
 
-			weim: weim@83fda000 {
+			weim: memory-controller@83fda000 {
 				#address-cells = <2>;
 				#size-cells = <1>;
 				compatible = "fsl,imx51-weim";
@@ -586,7 +595,7 @@
 				status = "disabled";
 			};
 
-			nfc: nand@83fdb000 {
+			nfc: nand-controller@83fdb000 {
 				#address-cells = <1>;
 				#size-cells = <1>;
 				compatible = "fsl,imx51-nand";
@@ -642,7 +651,7 @@
 			};
 
 			sahara: crypto@83ff8000 {
-				compatible = "fsl,imx53-sahara", "fsl,imx51-sahara";
+				compatible = "fsl,imx53-sahara";
 				reg = <0x83ff8000 0x4000>;
 				interrupts = <19 20>;
 				clocks = <&clks IMX5_CLK_SAHARA_IPG_GATE>,
diff --git a/arch/arm/boot/dts/nxp/imx/imx53-ard.dts b/arch/arm/boot/dts/nxp/imx/imx53-ard.dts
new file mode 100644
index 000000000000..e580427660b1
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx53-ard.dts
@@ -0,0 +1,170 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include "imx53.dtsi"
+
+/ {
+	model = "Freescale i.MX53 Automotive Reference Design Board";
+	compatible = "fsl,imx53-ard", "fsl,imx53";
+
+	memory@70000000 {
+		device_type = "memory";
+		reg = <0x70000000 0x40000000>;
+	};
+
+	eim-cs1@f4000000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "fsl,eim-bus", "simple-bus";
+		reg = <0xf4000000 0x3ff0000>;
+		ranges;
+
+		ethernet@f4000000 {
+			compatible = "smsc,lan9220", "smsc,lan9115";
+			reg = <0xf4000000 0x2000000>;
+			phy-mode = "mii";
+			interrupt-parent = <&gpio2>;
+			interrupts = <31 0x8>;
+			reg-io-width = <4>;
+			/*
+			 * VDD33A and VDDVARIO of LAN9220 are supplied by
+			 * SW4_3V3 of LTC3589.  Before the regulator driver
+			 * for this PMIC is available, we use a fixed dummy
+			 * 3V3 regulator to get LAN9220 driver probing work.
+			 */
+			vdd33a-supply = <&reg_3p3v>;
+			vddvario-supply = <&reg_3p3v>;
+			smsc,irq-push-pull;
+		};
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-home {
+			label = "Home";
+			gpios = <&gpio5 10 0>;
+			linux,code = <KEY_HOME>;
+			wakeup-source;
+		};
+
+		key-back {
+			label = "Back";
+			gpios = <&gpio5 11 0>;
+			linux,code = <KEY_BACK>;
+			wakeup-source;
+		};
+
+		key-program {
+			label = "Program";
+			gpios = <&gpio5 12 0>;
+			linux,code = <KEY_PROGRAM >;
+			wakeup-source;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio5 13 0>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio4 0 0>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+	};
+};
+
+&esdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc1>;
+	cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX53_PAD_GPIO_1__GPIO1_1             0x80000000
+			MX53_PAD_GPIO_9__GPIO1_9             0x80000000
+			MX53_PAD_EIM_EB3__GPIO2_31           0x80000000
+			MX53_PAD_GPIO_10__GPIO4_0            0x80000000
+			MX53_PAD_DISP0_DAT16__GPIO5_10	     0x80000000
+			MX53_PAD_DISP0_DAT17__GPIO5_11       0x80000000
+			MX53_PAD_DISP0_DAT18__GPIO5_12       0x80000000
+			MX53_PAD_DISP0_DAT19__GPIO5_13       0x80000000
+			MX53_PAD_EIM_D16__EMI_WEIM_D_16      0x80000000
+			MX53_PAD_EIM_D17__EMI_WEIM_D_17      0x80000000
+			MX53_PAD_EIM_D18__EMI_WEIM_D_18      0x80000000
+			MX53_PAD_EIM_D19__EMI_WEIM_D_19      0x80000000
+			MX53_PAD_EIM_D20__EMI_WEIM_D_20      0x80000000
+			MX53_PAD_EIM_D21__EMI_WEIM_D_21      0x80000000
+			MX53_PAD_EIM_D22__EMI_WEIM_D_22      0x80000000
+			MX53_PAD_EIM_D23__EMI_WEIM_D_23      0x80000000
+			MX53_PAD_EIM_D24__EMI_WEIM_D_24      0x80000000
+			MX53_PAD_EIM_D25__EMI_WEIM_D_25      0x80000000
+			MX53_PAD_EIM_D26__EMI_WEIM_D_26      0x80000000
+			MX53_PAD_EIM_D27__EMI_WEIM_D_27      0x80000000
+			MX53_PAD_EIM_D28__EMI_WEIM_D_28      0x80000000
+			MX53_PAD_EIM_D29__EMI_WEIM_D_29      0x80000000
+			MX53_PAD_EIM_D30__EMI_WEIM_D_30      0x80000000
+			MX53_PAD_EIM_D31__EMI_WEIM_D_31      0x80000000
+			MX53_PAD_EIM_DA0__EMI_NAND_WEIM_DA_0 0x80000000
+			MX53_PAD_EIM_DA1__EMI_NAND_WEIM_DA_1 0x80000000
+			MX53_PAD_EIM_DA2__EMI_NAND_WEIM_DA_2 0x80000000
+			MX53_PAD_EIM_DA3__EMI_NAND_WEIM_DA_3 0x80000000
+			MX53_PAD_EIM_DA4__EMI_NAND_WEIM_DA_4 0x80000000
+			MX53_PAD_EIM_DA5__EMI_NAND_WEIM_DA_5 0x80000000
+			MX53_PAD_EIM_DA6__EMI_NAND_WEIM_DA_6 0x80000000
+			MX53_PAD_EIM_OE__EMI_WEIM_OE	     0x80000000
+			MX53_PAD_EIM_RW__EMI_WEIM_RW	     0x80000000
+			MX53_PAD_EIM_CS1__EMI_WEIM_CS_1	     0x80000000
+		>;
+	};
+
+	pinctrl_esdhc1: esdhc1grp {
+		fsl,pins = <
+			MX53_PAD_SD1_DATA0__ESDHC1_DAT0		0x1d5
+			MX53_PAD_SD1_DATA1__ESDHC1_DAT1		0x1d5
+			MX53_PAD_SD1_DATA2__ESDHC1_DAT2		0x1d5
+			MX53_PAD_SD1_DATA3__ESDHC1_DAT3		0x1d5
+			MX53_PAD_PATA_DATA8__ESDHC1_DAT4	0x1d5
+			MX53_PAD_PATA_DATA9__ESDHC1_DAT5	0x1d5
+			MX53_PAD_PATA_DATA10__ESDHC1_DAT6	0x1d5
+			MX53_PAD_PATA_DATA11__ESDHC1_DAT7	0x1d5
+			MX53_PAD_SD1_CMD__ESDHC1_CMD		0x1d5
+			MX53_PAD_SD1_CLK__ESDHC1_CLK		0x1d5
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX53_PAD_PATA_DIOW__UART1_TXD_MUX	0x1e4
+			MX53_PAD_PATA_DMACK__UART1_RXD_MUX	0x1e4
+		>;
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx53-cx9020.dts b/arch/arm/boot/dts/nxp/imx/imx53-cx9020.dts
index cfb18849a92b..0814f5665a59 100644
--- a/arch/arm/boot/dts/imx53-cx9020.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-cx9020.dts
@@ -22,7 +22,7 @@
 	};
 
 	display-0 {
-		#address-cells =<1>;
+		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "fsl,imx-parallel-display";
 		interface-pix-fmt = "rgb24";
@@ -86,27 +86,27 @@
 	leds {
 		compatible = "gpio-leds";
 
-		pwr-r {
+		led-pwr-r {
 			gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 		};
 
-		pwr-g {
+		led-pwr-g {
 			gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 		};
 
-		pwr-b {
+		led-pwr-b {
 			gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 		};
 
-		sd1-b {
+		led-sd1-b {
 			linux,default-trigger = "mmc0";
 			gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
 		};
 
-		sd2-b {
+		led-sd2-b {
 			linux,default-trigger = "mmc1";
 			gpios = <&gpio3 17 GPIO_ACTIVE_HIGH>;
 		};
diff --git a/arch/arm/boot/dts/imx53-kp-ddc.dts b/arch/arm/boot/dts/nxp/imx/imx53-kp-ddc.dts
index 0e7f071fd10e..9c480e4d27ce 100644
--- a/arch/arm/boot/dts/imx53-kp-ddc.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-kp-ddc.dts
@@ -13,7 +13,7 @@
 
 	backlight_lcd: backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm2 0 50000>;
+		pwms = <&pwm2 0 50000 0>;
 		power-supply = <&reg_backlight>;
 		brightness-levels = <0 24 28 32 36
 				     40 44 48 52 56
@@ -102,38 +102,36 @@
 };
 
 &iomuxc {
-	imx53-kp-ddc {
-		pinctrl_disp: dispgrp {
-			fsl,pins = <
-				MX53_PAD_EIM_A16__IPU_DI1_DISP_CLK      0x4
-				MX53_PAD_EIM_DA10__IPU_DI1_PIN15        0x4
-				MX53_PAD_EIM_DA9__IPU_DISP1_DAT_0       0x4
-				MX53_PAD_EIM_DA8__IPU_DISP1_DAT_1       0x4
-				MX53_PAD_EIM_DA7__IPU_DISP1_DAT_2       0x4
-				MX53_PAD_EIM_DA6__IPU_DISP1_DAT_3       0x4
-				MX53_PAD_EIM_DA5__IPU_DISP1_DAT_4       0x4
-				MX53_PAD_EIM_DA4__IPU_DISP1_DAT_5       0x4
-				MX53_PAD_EIM_DA3__IPU_DISP1_DAT_6       0x4
-				MX53_PAD_EIM_DA2__IPU_DISP1_DAT_7       0x4
-				MX53_PAD_EIM_DA1__IPU_DISP1_DAT_8       0x4
-				MX53_PAD_EIM_DA0__IPU_DISP1_DAT_9       0x4
-				MX53_PAD_EIM_EB1__IPU_DISP1_DAT_10      0x4
-				MX53_PAD_EIM_EB0__IPU_DISP1_DAT_11      0x4
-				MX53_PAD_EIM_A17__IPU_DISP1_DAT_12      0x4
-				MX53_PAD_EIM_A18__IPU_DISP1_DAT_13      0x4
-				MX53_PAD_EIM_A19__IPU_DISP1_DAT_14      0x4
-				MX53_PAD_EIM_A20__IPU_DISP1_DAT_15      0x4
-				MX53_PAD_EIM_A21__IPU_DISP1_DAT_16      0x4
-				MX53_PAD_EIM_A22__IPU_DISP1_DAT_17      0x4
-				MX53_PAD_EIM_A23__IPU_DISP1_DAT_18      0x4
-				MX53_PAD_EIM_A24__IPU_DISP1_DAT_19      0x4
-				MX53_PAD_EIM_D31__IPU_DISP1_DAT_20      0x4
-				MX53_PAD_EIM_D30__IPU_DISP1_DAT_21      0x4
-				MX53_PAD_EIM_D26__IPU_DISP1_DAT_22      0x4
-				MX53_PAD_EIM_D27__IPU_DISP1_DAT_23      0x4
-				MX53_PAD_GPIO_1__PWM2_PWMO 0x4
-			>;
-		};
+	pinctrl_disp: dispgrp {
+		fsl,pins = <
+			MX53_PAD_EIM_A16__IPU_DI1_DISP_CLK      0x4
+			MX53_PAD_EIM_DA10__IPU_DI1_PIN15        0x4
+			MX53_PAD_EIM_DA9__IPU_DISP1_DAT_0       0x4
+			MX53_PAD_EIM_DA8__IPU_DISP1_DAT_1       0x4
+			MX53_PAD_EIM_DA7__IPU_DISP1_DAT_2       0x4
+			MX53_PAD_EIM_DA6__IPU_DISP1_DAT_3       0x4
+			MX53_PAD_EIM_DA5__IPU_DISP1_DAT_4       0x4
+			MX53_PAD_EIM_DA4__IPU_DISP1_DAT_5       0x4
+			MX53_PAD_EIM_DA3__IPU_DISP1_DAT_6       0x4
+			MX53_PAD_EIM_DA2__IPU_DISP1_DAT_7       0x4
+			MX53_PAD_EIM_DA1__IPU_DISP1_DAT_8       0x4
+			MX53_PAD_EIM_DA0__IPU_DISP1_DAT_9       0x4
+			MX53_PAD_EIM_EB1__IPU_DISP1_DAT_10      0x4
+			MX53_PAD_EIM_EB0__IPU_DISP1_DAT_11      0x4
+			MX53_PAD_EIM_A17__IPU_DISP1_DAT_12      0x4
+			MX53_PAD_EIM_A18__IPU_DISP1_DAT_13      0x4
+			MX53_PAD_EIM_A19__IPU_DISP1_DAT_14      0x4
+			MX53_PAD_EIM_A20__IPU_DISP1_DAT_15      0x4
+			MX53_PAD_EIM_A21__IPU_DISP1_DAT_16      0x4
+			MX53_PAD_EIM_A22__IPU_DISP1_DAT_17      0x4
+			MX53_PAD_EIM_A23__IPU_DISP1_DAT_18      0x4
+			MX53_PAD_EIM_A24__IPU_DISP1_DAT_19      0x4
+			MX53_PAD_EIM_D31__IPU_DISP1_DAT_20      0x4
+			MX53_PAD_EIM_D30__IPU_DISP1_DAT_21      0x4
+			MX53_PAD_EIM_D26__IPU_DISP1_DAT_22      0x4
+			MX53_PAD_EIM_D27__IPU_DISP1_DAT_23      0x4
+			MX53_PAD_GPIO_1__PWM2_PWMO 0x4
+		>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx53-kp-hsc.dts b/arch/arm/boot/dts/nxp/imx/imx53-kp-hsc.dts
index 6e3d71baac0f..6e3d71baac0f 100644
--- a/arch/arm/boot/dts/imx53-kp-hsc.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-kp-hsc.dts
diff --git a/arch/arm/boot/dts/imx53-kp.dtsi b/arch/arm/boot/dts/nxp/imx/imx53-kp.dtsi
index 4508f34139a0..543cf723008f 100644
--- a/arch/arm/boot/dts/imx53-kp.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx53-kp.dtsi
@@ -13,7 +13,7 @@
 		compatible = "pwm-beeper";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_buzzer>;
-		pwms = <&pwm1 0 500000>;
+		pwms = <&pwm1 0 500000 0>;
 	};
 
 	gpio-buttons {
@@ -42,14 +42,14 @@
 		led-bus {
 			label = "bus";
 			gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "gpio";
+			linux,default-trigger = "none";
 			default-state = "off";
 		};
 
 		led-error {
 			label = "error";
 			gpios = <&gpio3 28 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "gpio";
+			linux,default-trigger = "none";
 			default-state = "off";
 		};
 
@@ -98,56 +98,54 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_kp_common>;
 
-	imx53-kp-common {
-		pinctrl_buzzer: buzzergrp {
-			fsl,pins = <
-				MX53_PAD_SD1_DATA3__PWM1_PWMO 0x1e4
-			>;
-		};
+	pinctrl_buzzer: buzzergrp {
+		fsl,pins = <
+			MX53_PAD_SD1_DATA3__PWM1_PWMO 0x1e4
+		>;
+	};
 
-		pinctrl_gpiobuttons: gpiobuttonsgrp {
-			fsl,pins = <
-				MX53_PAD_EIM_RW__GPIO2_26 0x1e4
-				MX53_PAD_EIM_D22__GPIO3_22 0x1e4
-			>;
-		};
+	pinctrl_gpiobuttons: gpiobuttonsgrp {
+		fsl,pins = <
+			MX53_PAD_EIM_RW__GPIO2_26 0x1e4
+			MX53_PAD_EIM_D22__GPIO3_22 0x1e4
+		>;
+	};
 
-		pinctrl_kp_common: kpcommongrp {
-			fsl,pins = <
-				MX53_PAD_EIM_CS0__GPIO2_23 0x1e4
-				MX53_PAD_GPIO_19__GPIO4_5  0x1e4
-				MX53_PAD_PATA_DATA6__GPIO2_6 0x1e4
-				MX53_PAD_PATA_DATA7__GPIO2_7 0xe0
-				MX53_PAD_CSI0_DAT14__GPIO6_0 0x1e4
-				MX53_PAD_CSI0_DAT16__GPIO6_2 0x1e4
-				MX53_PAD_CSI0_DAT18__GPIO6_4 0x1e4
-				MX53_PAD_EIM_D17__GPIO3_17 0x1e4
-				MX53_PAD_EIM_D18__GPIO3_18 0x1e4
-				MX53_PAD_EIM_D21__GPIO3_21 0x1e4
-				MX53_PAD_EIM_D29__GPIO3_29 0x1e4
-				MX53_PAD_EIM_DA11__GPIO3_11 0x1e4
-				MX53_PAD_EIM_DA13__GPIO3_13 0x1e4
-				MX53_PAD_EIM_DA14__GPIO3_14 0x1e4
-				MX53_PAD_SD1_DATA0__GPIO1_16 0x1e4
-				MX53_PAD_SD1_CMD__GPIO1_18 0x1e4
-				MX53_PAD_SD1_CLK__GPIO1_20 0x1e4
-			>;
-		};
+	pinctrl_kp_common: kpcommongrp {
+		fsl,pins = <
+			MX53_PAD_EIM_CS0__GPIO2_23 0x1e4
+			MX53_PAD_GPIO_19__GPIO4_5  0x1e4
+			MX53_PAD_PATA_DATA6__GPIO2_6 0x1e4
+			MX53_PAD_PATA_DATA7__GPIO2_7 0xe0
+			MX53_PAD_CSI0_DAT14__GPIO6_0 0x1e4
+			MX53_PAD_CSI0_DAT16__GPIO6_2 0x1e4
+			MX53_PAD_CSI0_DAT18__GPIO6_4 0x1e4
+			MX53_PAD_EIM_D17__GPIO3_17 0x1e4
+			MX53_PAD_EIM_D18__GPIO3_18 0x1e4
+			MX53_PAD_EIM_D21__GPIO3_21 0x1e4
+			MX53_PAD_EIM_D29__GPIO3_29 0x1e4
+			MX53_PAD_EIM_DA11__GPIO3_11 0x1e4
+			MX53_PAD_EIM_DA13__GPIO3_13 0x1e4
+			MX53_PAD_EIM_DA14__GPIO3_14 0x1e4
+			MX53_PAD_SD1_DATA0__GPIO1_16 0x1e4
+			MX53_PAD_SD1_CMD__GPIO1_18 0x1e4
+			MX53_PAD_SD1_CLK__GPIO1_20 0x1e4
+		>;
+	};
 
-		pinctrl_leds: ledgrp {
-			fsl,pins = <
-				MX53_PAD_EIM_EB2__GPIO2_30 0x1d4
-				MX53_PAD_EIM_D28__GPIO3_28 0x1d4
-				MX53_PAD_EIM_WAIT__GPIO5_0 0x1d4
-			>;
-		};
+	pinctrl_leds: ledgrp {
+		fsl,pins = <
+			MX53_PAD_EIM_EB2__GPIO2_30 0x1d4
+			MX53_PAD_EIM_D28__GPIO3_28 0x1d4
+			MX53_PAD_EIM_WAIT__GPIO5_0 0x1d4
+		>;
+	};
 
-		pinctrl_uart4: uart4grp {
-			fsl,pins = <
-				MX53_PAD_CSI0_DAT12__UART4_TXD_MUX 0x1e4
-				MX53_PAD_CSI0_DAT13__UART4_RXD_MUX 0x1e4
-			>;
-		};
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX53_PAD_CSI0_DAT12__UART4_TXD_MUX 0x1e4
+			MX53_PAD_CSI0_DAT13__UART4_RXD_MUX 0x1e4
+		>;
 	};
 };
 
@@ -162,14 +160,6 @@
 	>;
 };
 
-&pwm1 {
-	#pwm-cells = <2>;
-};
-
-&pwm2 {
-	#pwm-cells = <2>;
-};
-
 &uart1 {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/nxp/imx/imx53-m53.dtsi b/arch/arm/boot/dts/nxp/imx/imx53-m53.dtsi
new file mode 100644
index 000000000000..89b17509ad48
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx53-m53.dtsi
@@ -0,0 +1,122 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2014 Marek Vasut <marex@denx.de>
+ */
+
+#include "imx53.dtsi"
+
+/ {
+	model = "Aries/DENX M53";
+	compatible = "aries,imx53-m53", "denx,imx53-m53", "fsl,imx53";
+
+	memory@70000000 {
+		device_type = "memory";
+		reg = <0x70000000 0x20000000>,
+		      <0xb0000000 0x20000000>;
+	};
+
+	reg_3p2v: regulator-3p2v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P2V";
+		regulator-min-microvolt = <3200000>;
+		regulator-max-microvolt = <3200000>;
+		regulator-always-on;
+	};
+
+	reg_backlight: regulator-backlight {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-supply";
+		regulator-min-microvolt = <3200000>;
+		regulator-max-microvolt = <3200000>;
+		regulator-always-on;
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	touchscreen@41 {
+		compatible = "st,stmpe610";
+		reg = <0x41>;
+		id = <0>;
+		blocks = <0x5>;
+		interrupts = <6 0x0>;
+		interrupt-parent = <&gpio7>;
+		irq-trigger = <0x1>;
+
+		touchscreen {
+			compatible = "st,stmpe-ts";
+			st,sample-time = <4>;
+			st,mod-12b = <1>;
+			st,ref-sel = <0>;
+			st,adc-freq = <1>;
+			st,ave-ctrl = <3>;
+			st,touch-det-delay = <3>;
+			st,settling = <4>;
+			st,fraction-z = <7>;
+			st,i-drive = <1>;
+		};
+	};
+
+	eeprom: eeprom@50 {
+		compatible = "atmel,24c128";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	rtc: rtc@68 {
+		compatible = "st,m41t62";
+		reg = <0x68>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK	0x80000000
+			MX53_PAD_EIM_EB3__GPIO2_31		0x80000000
+			MX53_PAD_PATA_DA_0__GPIO7_6		0x80000000
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX53_PAD_EIM_D16__I2C2_SDA		0xc0000000
+			MX53_PAD_EIM_EB2__I2C2_SCL		0xc0000000
+		>;
+	};
+
+	pinctrl_nand: nandgrp {
+		fsl,pins = <
+			MX53_PAD_NANDF_WE_B__EMI_NANDF_WE_B	0x4
+			MX53_PAD_NANDF_RE_B__EMI_NANDF_RE_B	0x4
+			MX53_PAD_NANDF_CLE__EMI_NANDF_CLE	0x4
+			MX53_PAD_NANDF_ALE__EMI_NANDF_ALE	0x4
+			MX53_PAD_NANDF_WP_B__EMI_NANDF_WP_B	0xe0
+			MX53_PAD_NANDF_RB0__EMI_NANDF_RB_0	0xe0
+			MX53_PAD_NANDF_CS0__EMI_NANDF_CS_0	0x4
+			MX53_PAD_PATA_DATA0__EMI_NANDF_D_0	0xa4
+			MX53_PAD_PATA_DATA1__EMI_NANDF_D_1	0xa4
+			MX53_PAD_PATA_DATA2__EMI_NANDF_D_2	0xa4
+			MX53_PAD_PATA_DATA3__EMI_NANDF_D_3	0xa4
+			MX53_PAD_PATA_DATA4__EMI_NANDF_D_4	0xa4
+			MX53_PAD_PATA_DATA5__EMI_NANDF_D_5	0xa4
+			MX53_PAD_PATA_DATA6__EMI_NANDF_D_6	0xa4
+			MX53_PAD_PATA_DATA7__EMI_NANDF_D_7	0xa4
+		>;
+	};
+};
+
+&nfc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_nand>;
+	nand-bus-width = <8>;
+	nand-ecc-mode = "hw";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx53-m53evk.dts b/arch/arm/boot/dts/nxp/imx/imx53-m53evk.dts
new file mode 100644
index 000000000000..eb3d66305395
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx53-m53evk.dts
@@ -0,0 +1,360 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2013 Marek Vasut <marex@denx.de>
+ */
+
+/dts-v1/;
+#include "imx53-m53.dtsi"
+
+/ {
+	model = "Aries/DENX M53EVK";
+	compatible = "aries,imx53-m53evk", "denx,imx53-m53evk", "fsl,imx53";
+
+	display1: disp1 {
+		compatible = "fsl,imx-parallel-display";
+		interface-pix-fmt = "bgr666";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu_disp1>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing-800x480p60 {
+				clock-frequency = <31500000>;
+				hactive = <800>;
+				vactive = <480>;
+				hfront-porch = <40>;
+				hback-porch = <88>;
+				hsync-len = <128>;
+				vback-porch = <33>;
+				vfront-porch = <9>;
+				vsync-len = <3>;
+				vsync-active = <1>;
+			};
+		};
+
+		port {
+			display1_in: endpoint {
+				remote-endpoint = <&ipu_di1_disp1>;
+			};
+		};
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 3000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+		power-supply = <&reg_backlight>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pin_gpio>;
+
+		led-user1 {
+			label = "user1";
+			gpios = <&gpio2 8 0>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-user2 {
+			label = "user2";
+			gpios = <&gpio2 9 0>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	reg_usbh1_vbus: regulator-usbh1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 2 0>;
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 4 0>;
+	};
+
+	sound {
+		compatible = "fsl,imx53-m53evk-sgtl5000",
+			     "fsl,imx-audio-sgtl5000";
+		model = "imx53-m53evk-sgtl5000";
+		ssi-controller = <&ssi2>;
+		audio-codec = <&sgtl5000>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT",
+			"Ext Spk", "LINE_OUT";
+		mux-int-port = <2>;
+		mux-ext-port = <4>;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can2>;
+	status = "okay";
+};
+
+&esdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc1>;
+	cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec>;
+	phy-mode = "rmii";
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	sgtl5000: codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		VDDA-supply = <&reg_3p2v>;
+		VDDIO-supply = <&reg_3p2v>;
+		clocks = <&clks IMX5_CLK_SSI_EXT1_GATE>;
+	};
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_usb: usbgrp {
+		fsl,pins = <
+			MX53_PAD_GPIO_2__GPIO1_2		0x80000000
+			MX53_PAD_GPIO_3__USBOH3_USBH1_OC	0x80000000
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX53_PAD_GPIO_4__GPIO1_4		0x000b0
+		>;
+	};
+
+	led_pin_gpio: ledgpiogrp {
+		fsl,pins = <
+			MX53_PAD_PATA_DATA8__GPIO2_8		0x80000000
+			MX53_PAD_PATA_DATA9__GPIO2_9		0x80000000
+		>;
+	};
+
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX53_PAD_SD2_DATA3__AUDMUX_AUD4_TXC	0x80000000
+			MX53_PAD_SD2_DATA2__AUDMUX_AUD4_TXD	0x80000000
+			MX53_PAD_SD2_DATA1__AUDMUX_AUD4_TXFS	0x80000000
+			MX53_PAD_SD2_DATA0__AUDMUX_AUD4_RXD	0x80000000
+		>;
+	};
+
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX53_PAD_GPIO_7__CAN1_TXCAN		0x80000000
+			MX53_PAD_GPIO_8__CAN1_RXCAN		0x80000000
+		>;
+	};
+
+	pinctrl_can2: can2grp {
+		fsl,pins = <
+			MX53_PAD_KEY_COL4__CAN2_TXCAN		0x80000000
+			MX53_PAD_KEY_ROW4__CAN2_RXCAN		0x80000000
+		>;
+	};
+
+	pinctrl_esdhc1: esdhc1grp {
+		fsl,pins = <
+			MX53_PAD_SD1_DATA0__ESDHC1_DAT0		0x1d5
+			MX53_PAD_SD1_DATA1__ESDHC1_DAT1		0x1d5
+			MX53_PAD_SD1_DATA2__ESDHC1_DAT2		0x1d5
+			MX53_PAD_SD1_DATA3__ESDHC1_DAT3		0x1d5
+			MX53_PAD_SD1_CMD__ESDHC1_CMD		0x1d5
+			MX53_PAD_SD1_CLK__ESDHC1_CLK		0x1d5
+		>;
+	};
+
+	pinctrl_fec: fecgrp {
+		fsl,pins = <
+			MX53_PAD_FEC_MDC__FEC_MDC		0x80000000
+			MX53_PAD_FEC_MDIO__FEC_MDIO		0x80000000
+			MX53_PAD_FEC_REF_CLK__FEC_TX_CLK	0x80000000
+			MX53_PAD_FEC_RX_ER__FEC_RX_ER		0x80000000
+			MX53_PAD_FEC_CRS_DV__FEC_RX_DV		0x80000000
+			MX53_PAD_FEC_RXD1__FEC_RDATA_1		0x80000000
+			MX53_PAD_FEC_RXD0__FEC_RDATA_0		0x80000000
+			MX53_PAD_FEC_TX_EN__FEC_TX_EN		0x80000000
+			MX53_PAD_FEC_TXD1__FEC_TDATA_1		0x80000000
+			MX53_PAD_FEC_TXD0__FEC_TDATA_0		0x80000000
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX53_PAD_EIM_D21__I2C1_SCL		0xc0000000
+			MX53_PAD_EIM_D28__I2C1_SDA		0xc0000000
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX53_PAD_GPIO_6__I2C3_SDA		0xc0000000
+			MX53_PAD_GPIO_5__I2C3_SCL		0xc0000000
+		>;
+	};
+
+	pinctrl_ipu_disp1: ipudisp1grp {
+		fsl,pins = <
+			MX53_PAD_EIM_DA9__IPU_DISP1_DAT_0	0x5
+			MX53_PAD_EIM_DA8__IPU_DISP1_DAT_1	0x5
+			MX53_PAD_EIM_DA7__IPU_DISP1_DAT_2	0x5
+			MX53_PAD_EIM_DA6__IPU_DISP1_DAT_3	0x5
+			MX53_PAD_EIM_DA5__IPU_DISP1_DAT_4	0x5
+			MX53_PAD_EIM_DA4__IPU_DISP1_DAT_5	0x5
+			MX53_PAD_EIM_DA3__IPU_DISP1_DAT_6	0x5
+			MX53_PAD_EIM_DA2__IPU_DISP1_DAT_7	0x5
+			MX53_PAD_EIM_DA1__IPU_DISP1_DAT_8	0x5
+			MX53_PAD_EIM_DA0__IPU_DISP1_DAT_9	0x5
+			MX53_PAD_EIM_EB1__IPU_DISP1_DAT_10	0x5
+			MX53_PAD_EIM_EB0__IPU_DISP1_DAT_11	0x5
+			MX53_PAD_EIM_A17__IPU_DISP1_DAT_12	0x5
+			MX53_PAD_EIM_A18__IPU_DISP1_DAT_13	0x5
+			MX53_PAD_EIM_A19__IPU_DISP1_DAT_14	0x5
+			MX53_PAD_EIM_A20__IPU_DISP1_DAT_15	0x5
+			MX53_PAD_EIM_A21__IPU_DISP1_DAT_16	0x5
+			MX53_PAD_EIM_A22__IPU_DISP1_DAT_17	0x5
+			MX53_PAD_EIM_A23__IPU_DISP1_DAT_18	0x5
+			MX53_PAD_EIM_A24__IPU_DISP1_DAT_19	0x5
+			MX53_PAD_EIM_D31__IPU_DISP1_DAT_20	0x5
+			MX53_PAD_EIM_D30__IPU_DISP1_DAT_21	0x5
+			MX53_PAD_EIM_D26__IPU_DISP1_DAT_22	0x5
+			MX53_PAD_EIM_D27__IPU_DISP1_DAT_23	0x5
+			MX53_PAD_EIM_A16__IPU_DI1_DISP_CLK	0x5
+			MX53_PAD_EIM_DA13__IPU_DI1_D0_CS	0x5
+			MX53_PAD_EIM_DA14__IPU_DI1_D1_CS	0x5
+			MX53_PAD_EIM_DA15__IPU_DI1_PIN1		0x5
+			MX53_PAD_EIM_DA11__IPU_DI1_PIN2		0x5
+			MX53_PAD_EIM_DA12__IPU_DI1_PIN3		0x5
+			MX53_PAD_EIM_A25__IPU_DI1_PIN12		0x5
+			MX53_PAD_EIM_DA10__IPU_DI1_PIN15	0x5
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX53_PAD_DISP0_DAT8__PWM1_PWMO		0x5
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX53_PAD_PATA_DIOW__UART1_TXD_MUX	0x1e4
+			MX53_PAD_PATA_DMACK__UART1_RXD_MUX	0x1e4
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX	0x1e4
+			MX53_PAD_PATA_DMARQ__UART2_TXD_MUX	0x1e4
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX53_PAD_PATA_CS_0__UART3_TXD_MUX	0x1e4
+			MX53_PAD_PATA_CS_1__UART3_RXD_MUX	0x1e4
+			MX53_PAD_PATA_DA_1__UART3_CTS		0x1e4
+			MX53_PAD_PATA_DA_2__UART3_RTS		0x1e4
+		>;
+	};
+};
+
+&ipu_di1_disp1 {
+	remote-endpoint = <&display1_in>;
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&ssi2 {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&usbh1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb>;
+	vbus-supply = <&reg_usbh1_vbus>;
+	phy_type = "utmi";
+	status = "okay";
+};
+
+&usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	dr_mode = "otg";
+	vbus-supply = <&reg_usb_otg_vbus>;
+	disable-over-current;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx53-m53menlo.dts b/arch/arm/boot/dts/nxp/imx/imx53-m53menlo.dts
index d5c68d1ea707..6210673f93be 100644
--- a/arch/arm/boot/dts/imx53-m53menlo.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-m53menlo.dts
@@ -34,19 +34,19 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_led>;
 
-		user1 {
+		led-user1 {
 			label = "TestLed601";
 			gpios = <&gpio6 1 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "mmc0";
 		};
 
-		user2 {
+		led-user2 {
 			label = "TestLed602";
 			gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 
-		eth {
+		led-eth {
 			label = "EthLedYe";
 			gpios = <&gpio2 11 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "netdev";
@@ -64,6 +64,7 @@
 				reg = <0>;
 
 				lvds_decoder_in: endpoint {
+					data-mapping = "jeida-18";
 					remote-endpoint = <&lvds0_out>;
 				};
 			};
@@ -277,186 +278,184 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hog>;
 
-	imx53-m53evk {
-		hoggrp {
-			fsl,pins = <
-				MX53_PAD_GPIO_19__CCM_CLKO		0x1e4
-				MX53_PAD_CSI0_DATA_EN__GPIO5_20		0x1e4
-				MX53_PAD_CSI0_DAT4__GPIO5_22		0x1e4
-				MX53_PAD_CSI0_DAT5__GPIO5_23		0x1c4
-				MX53_PAD_CSI0_DAT6__GPIO5_24		0x1e4
-				MX53_PAD_CSI0_DAT7__GPIO5_25		0x1e4
-				MX53_PAD_CSI0_DAT8__GPIO5_26		0x1e4
-				MX53_PAD_CSI0_DAT9__GPIO5_27		0x1c4
-				MX53_PAD_CSI0_DAT10__GPIO5_28		0x1e4
-				MX53_PAD_CSI0_DAT11__GPIO5_29		0x1e4
-				MX53_PAD_PATA_DATA11__GPIO2_11		0x1e4
-				MX53_PAD_EIM_D24__GPIO3_24		0x1e4
-				MX53_PAD_EIM_D25__GPIO3_25		0x1e4
-				MX53_PAD_EIM_D29__GPIO3_29		0x1e4
-				MX53_PAD_CSI0_PIXCLK__GPIO5_18		0x1e4
-				MX53_PAD_CSI0_VSYNC__GPIO5_21		0x1e4
-				MX53_PAD_CSI0_DAT18__GPIO6_4		0x1c4
-				MX53_PAD_PATA_DATA8__GPIO2_8		0x1e4
-			>;
-		};
+	hoggrp {
+		fsl,pins = <
+			MX53_PAD_GPIO_19__CCM_CLKO		0x1e4
+			MX53_PAD_CSI0_DATA_EN__GPIO5_20		0x1e4
+			MX53_PAD_CSI0_DAT4__GPIO5_22		0x1e4
+			MX53_PAD_CSI0_DAT5__GPIO5_23		0x1c4
+			MX53_PAD_CSI0_DAT6__GPIO5_24		0x1e4
+			MX53_PAD_CSI0_DAT7__GPIO5_25		0x1e4
+			MX53_PAD_CSI0_DAT8__GPIO5_26		0x1e4
+			MX53_PAD_CSI0_DAT9__GPIO5_27		0x1c4
+			MX53_PAD_CSI0_DAT10__GPIO5_28		0x1e4
+			MX53_PAD_CSI0_DAT11__GPIO5_29		0x1e4
+			MX53_PAD_PATA_DATA11__GPIO2_11		0x1e4
+			MX53_PAD_EIM_D24__GPIO3_24		0x1e4
+			MX53_PAD_EIM_D25__GPIO3_25		0x1e4
+			MX53_PAD_EIM_D29__GPIO3_29		0x1e4
+			MX53_PAD_CSI0_PIXCLK__GPIO5_18		0x1e4
+			MX53_PAD_CSI0_VSYNC__GPIO5_21		0x1e4
+			MX53_PAD_CSI0_DAT18__GPIO6_4		0x1c4
+			MX53_PAD_PATA_DATA8__GPIO2_8		0x1e4
+		>;
+	};
 
-		pinctrl_led: ledgrp {
-			fsl,pins = <
-				MX53_PAD_CSI0_DAT15__GPIO6_1		0x1c4
-				MX53_PAD_CSI0_DAT16__GPIO6_2		0x1c4
-			>;
-		};
+	pinctrl_led: ledgrp {
+		fsl,pins = <
+			MX53_PAD_CSI0_DAT15__GPIO6_1		0x1c4
+			MX53_PAD_CSI0_DAT16__GPIO6_2		0x1c4
+		>;
+	};
 
-		pinctrl_beeper: beepergrp {
-			fsl,pins = <
-				MX53_PAD_CSI0_DAT17__GPIO6_3		0x1c4
-			>;
-		};
+	pinctrl_beeper: beepergrp {
+		fsl,pins = <
+			MX53_PAD_CSI0_DAT17__GPIO6_3		0x1c4
+		>;
+	};
 
-		pinctrl_can1: can1grp {
-			fsl,pins = <
-				MX53_PAD_GPIO_7__CAN1_TXCAN		0x1c4
-				MX53_PAD_GPIO_8__CAN1_RXCAN		0x1c4
-			>;
-		};
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX53_PAD_GPIO_7__CAN1_TXCAN		0x1c4
+			MX53_PAD_GPIO_8__CAN1_RXCAN		0x1c4
+		>;
+	};
 
-		pinctrl_can2: can2grp {
-			fsl,pins = <
-				MX53_PAD_KEY_COL4__CAN2_TXCAN		0x1e4
-				MX53_PAD_KEY_ROW4__CAN2_RXCAN		0x1c4
-			>;
-		};
+	pinctrl_can2: can2grp {
+		fsl,pins = <
+			MX53_PAD_KEY_COL4__CAN2_TXCAN		0x1e4
+			MX53_PAD_KEY_ROW4__CAN2_RXCAN		0x1c4
+		>;
+	};
 
-		pinctrl_display_gpio: display-gpiogrp {
-			fsl,pins = <
-				MX53_PAD_CSI0_DAT12__GPIO5_30		0x1c4 /* Reset */
-				MX53_PAD_CSI0_MCLK__GPIO5_19		0x1e4 /* Int-K */
-				MX53_PAD_CSI0_DAT13__GPIO5_31		0x1c4 /* Int-I */
+	pinctrl_display_gpio: display-gpiogrp {
+		fsl,pins = <
+			MX53_PAD_CSI0_DAT12__GPIO5_30		0x1c4 /* Reset */
+			MX53_PAD_CSI0_MCLK__GPIO5_19		0x1e4 /* Int-K */
+			MX53_PAD_CSI0_DAT13__GPIO5_31		0x1c4 /* Int-I */
 
-				MX53_PAD_CSI0_DAT14__GPIO6_0		0x1c4 /* Power down */
-			>;
-		};
+			MX53_PAD_CSI0_DAT14__GPIO6_0		0x1c4 /* Power down */
+		>;
+	};
 
-		pinctrl_edt_ft5x06: edt-ft5x06grp {
-			fsl,pins = <
-				MX53_PAD_PATA_DATA9__GPIO2_9		0x1e4 /* Reset */
-				MX53_PAD_CSI0_DAT19__GPIO6_5		0x1c4 /* Interrupt */
-				MX53_PAD_PATA_DATA10__GPIO2_10		0x1e4 /* Wake */
-			>;
-		};
+	pinctrl_edt_ft5x06: edt-ft5x06grp {
+		fsl,pins = <
+			MX53_PAD_PATA_DATA9__GPIO2_9		0x1e4 /* Reset */
+			MX53_PAD_CSI0_DAT19__GPIO6_5		0x1c4 /* Interrupt */
+			MX53_PAD_PATA_DATA10__GPIO2_10		0x1e4 /* Wake */
+		>;
+	};
 
-		pinctrl_ecspi2: ecspi2grp {
-			fsl,pins = <
-				MX53_PAD_EIM_CS0__ECSPI2_SCLK		0xe4
-				MX53_PAD_EIM_OE__ECSPI2_MISO		0xe4
-				MX53_PAD_EIM_CS1__ECSPI2_MOSI		0xe4
-				MX53_PAD_EIM_RW__GPIO2_26		0xe4
-				MX53_PAD_EIM_LBA__GPIO2_27		0xe4
-			>;
-		};
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX53_PAD_EIM_CS0__ECSPI2_SCLK		0xe4
+			MX53_PAD_EIM_OE__ECSPI2_MISO		0xe4
+			MX53_PAD_EIM_CS1__ECSPI2_MOSI		0xe4
+			MX53_PAD_EIM_RW__GPIO2_26		0xe4
+			MX53_PAD_EIM_LBA__GPIO2_27		0xe4
+		>;
+	};
 
-		pinctrl_esdhc1: esdhc1grp {
-			fsl,pins = <
-				MX53_PAD_SD1_DATA0__ESDHC1_DAT0		0x1e4
-				MX53_PAD_SD1_DATA1__ESDHC1_DAT1		0x1e4
-				MX53_PAD_SD1_DATA2__ESDHC1_DAT2		0x1e4
-				MX53_PAD_SD1_DATA3__ESDHC1_DAT3		0x1e4
-				MX53_PAD_SD1_CMD__ESDHC1_CMD		0x1e4
-				MX53_PAD_SD1_CLK__ESDHC1_CLK		0x1e4
-				MX53_PAD_GPIO_1__GPIO1_1		0x1c4
-				MX53_PAD_GPIO_9__GPIO1_9		0x1e4
-			>;
-		};
+	pinctrl_esdhc1: esdhc1grp {
+		fsl,pins = <
+			MX53_PAD_SD1_DATA0__ESDHC1_DAT0		0x1e4
+			MX53_PAD_SD1_DATA1__ESDHC1_DAT1		0x1e4
+			MX53_PAD_SD1_DATA2__ESDHC1_DAT2		0x1e4
+			MX53_PAD_SD1_DATA3__ESDHC1_DAT3		0x1e4
+			MX53_PAD_SD1_CMD__ESDHC1_CMD		0x1e4
+			MX53_PAD_SD1_CLK__ESDHC1_CLK		0x1e4
+			MX53_PAD_GPIO_1__GPIO1_1		0x1c4
+			MX53_PAD_GPIO_9__GPIO1_9		0x1e4
+		>;
+	};
 
-		pinctrl_fec: fecgrp {
-			fsl,pins = <
-				MX53_PAD_FEC_MDC__FEC_MDC		0x1e4
-				MX53_PAD_FEC_MDIO__FEC_MDIO		0x1e4
-				MX53_PAD_FEC_REF_CLK__FEC_TX_CLK	0x1e4
-				MX53_PAD_FEC_RX_ER__FEC_RX_ER		0x1e4
-				MX53_PAD_FEC_CRS_DV__FEC_RX_DV		0x1e4
-				MX53_PAD_FEC_RXD1__FEC_RDATA_1		0x1e4
-				MX53_PAD_FEC_RXD0__FEC_RDATA_0		0x1e4
-				MX53_PAD_FEC_TX_EN__FEC_TX_EN		0x1c4
-				MX53_PAD_FEC_TXD1__FEC_TDATA_1		0x1e4
-				MX53_PAD_FEC_TXD0__FEC_TDATA_0		0x1e4
-				MX53_PAD_PATA_DA_1__GPIO7_7		0x1e4
-				MX53_PAD_EIM_EB3__GPIO2_31		0x1e4
-			>;
-		};
+	pinctrl_fec: fecgrp {
+		fsl,pins = <
+			MX53_PAD_FEC_MDC__FEC_MDC		0x1e4
+			MX53_PAD_FEC_MDIO__FEC_MDIO		0x1e4
+			MX53_PAD_FEC_REF_CLK__FEC_TX_CLK	0x1e4
+			MX53_PAD_FEC_RX_ER__FEC_RX_ER		0x1e4
+			MX53_PAD_FEC_CRS_DV__FEC_RX_DV		0x1e4
+			MX53_PAD_FEC_RXD1__FEC_RDATA_1		0x1e4
+			MX53_PAD_FEC_RXD0__FEC_RDATA_0		0x1e4
+			MX53_PAD_FEC_TX_EN__FEC_TX_EN		0x1c4
+			MX53_PAD_FEC_TXD1__FEC_TDATA_1		0x1e4
+			MX53_PAD_FEC_TXD0__FEC_TDATA_0		0x1e4
+			MX53_PAD_PATA_DA_1__GPIO7_7		0x1e4
+			MX53_PAD_EIM_EB3__GPIO2_31		0x1e4
+		>;
+	};
 
-		pinctrl_i2c1: i2c1grp {
-			fsl,pins = <
-				MX53_PAD_EIM_D21__I2C1_SCL		0x400001e4
-				MX53_PAD_EIM_D28__I2C1_SDA		0x400001e4
-			>;
-		};
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX53_PAD_EIM_D21__I2C1_SCL		0x400001e4
+			MX53_PAD_EIM_D28__I2C1_SDA		0x400001e4
+		>;
+	};
 
-		pinctrl_i2c3: i2c3grp {
-			fsl,pins = <
-				MX53_PAD_GPIO_6__I2C3_SDA		0x400001e4
-				MX53_PAD_GPIO_5__I2C3_SCL		0x400001e4
-			>;
-		};
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX53_PAD_GPIO_6__I2C3_SDA		0x400001e4
+			MX53_PAD_GPIO_5__I2C3_SCL		0x400001e4
+		>;
+	};
 
-		pinctrl_lvds0: lvds0grp {
-			/* LVDS pins only have pin mux configuration */
-			fsl,pins = <
-				MX53_PAD_LVDS0_CLK_P__LDB_LVDS0_CLK	0x80000000
-				MX53_PAD_LVDS0_TX0_P__LDB_LVDS0_TX0	0x80000000
-				MX53_PAD_LVDS0_TX1_P__LDB_LVDS0_TX1	0x80000000
-				MX53_PAD_LVDS0_TX2_P__LDB_LVDS0_TX2	0x80000000
-				MX53_PAD_LVDS0_TX3_P__LDB_LVDS0_TX3	0x80000000
-			>;
-		};
+	pinctrl_lvds0: lvds0grp {
+		/* LVDS pins only have pin mux configuration */
+		fsl,pins = <
+			MX53_PAD_LVDS0_CLK_P__LDB_LVDS0_CLK	0x80000000
+			MX53_PAD_LVDS0_TX0_P__LDB_LVDS0_TX0	0x80000000
+			MX53_PAD_LVDS0_TX1_P__LDB_LVDS0_TX1	0x80000000
+			MX53_PAD_LVDS0_TX2_P__LDB_LVDS0_TX2	0x80000000
+			MX53_PAD_LVDS0_TX3_P__LDB_LVDS0_TX3	0x80000000
+		>;
+	};
 
-		pinctrl_power_button: powerbutgrp {
-			fsl,pins = <
-				MX53_PAD_SD2_DATA0__GPIO1_15		0x1e4
-			>;
-		};
+	pinctrl_power_button: powerbutgrp {
+		fsl,pins = <
+			MX53_PAD_SD2_DATA0__GPIO1_15		0x1e4
+		>;
+	};
 
-		pinctrl_power_out: poweroutgrp {
-			fsl,pins = <
-				MX53_PAD_SD2_DATA2__GPIO1_13		0x1e4
-			>;
-		};
+	pinctrl_power_out: poweroutgrp {
+		fsl,pins = <
+			MX53_PAD_SD2_DATA2__GPIO1_13		0x1e4
+		>;
+	};
 
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX53_PAD_PATA_DIOW__UART1_TXD_MUX	0x1e4
-				MX53_PAD_PATA_DMACK__UART1_RXD_MUX	0x1e4
-				MX53_PAD_PATA_IORDY__UART1_RTS		0x1e4
-				MX53_PAD_PATA_RESET_B__UART1_CTS	0x1e4
-			>;
-		};
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX53_PAD_PATA_DIOW__UART1_TXD_MUX	0x1e4
+			MX53_PAD_PATA_DMACK__UART1_RXD_MUX	0x1e4
+			MX53_PAD_PATA_IORDY__UART1_RTS		0x1e4
+			MX53_PAD_PATA_RESET_B__UART1_CTS	0x1e4
+		>;
+	};
 
-		pinctrl_uart2: uart2grp {
-			fsl,pins = <
-				MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX	0x1e4
-				MX53_PAD_PATA_DMARQ__UART2_TXD_MUX	0x1e4
-				MX53_PAD_PATA_DIOR__UART2_RTS		0x1e4
-				MX53_PAD_PATA_INTRQ__UART2_CTS		0x1e4
-			>;
-		};
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX	0x1e4
+			MX53_PAD_PATA_DMARQ__UART2_TXD_MUX	0x1e4
+			MX53_PAD_PATA_DIOR__UART2_RTS		0x1e4
+			MX53_PAD_PATA_INTRQ__UART2_CTS		0x1e4
+		>;
+	};
 
-		pinctrl_uart3: uart3grp {
-			fsl,pins = <
-				MX53_PAD_PATA_CS_1__UART3_RXD_MUX	0x1e4
-				MX53_PAD_PATA_CS_0__UART3_TXD_MUX	0x1e4
-				MX53_PAD_PATA_DA_2__UART3_RTS		0x1e4
-			>;
-		};
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX53_PAD_PATA_CS_1__UART3_RXD_MUX	0x1e4
+			MX53_PAD_PATA_CS_0__UART3_TXD_MUX	0x1e4
+			MX53_PAD_PATA_DA_2__UART3_RTS		0x1e4
+		>;
+	};
 
-		pinctrl_usb: usbgrp {
-			fsl,pins = <
-				MX53_PAD_GPIO_2__GPIO1_2		0x1c4
-				MX53_PAD_GPIO_3__USBOH3_USBH1_OC	0x1c4
-				MX53_PAD_GPIO_4__GPIO1_4		0x1c4
-				MX53_PAD_GPIO_18__GPIO7_13		0x1c4
-			>;
-		};
+	pinctrl_usb: usbgrp {
+		fsl,pins = <
+			MX53_PAD_GPIO_2__GPIO1_2		0x1c4
+			MX53_PAD_GPIO_3__USBOH3_USBH1_OC	0x1c4
+			MX53_PAD_GPIO_4__GPIO1_4		0x1c4
+			MX53_PAD_GPIO_18__GPIO7_13		0x1c4
+		>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/nxp/imx/imx53-mba53.dts b/arch/arm/boot/dts/nxp/imx/imx53-mba53.dts
new file mode 100644
index 000000000000..3cdb87ac1d7c
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx53-mba53.dts
@@ -0,0 +1,236 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
+ * Copyright 2012 Steffen Trumtrar <s.trumtrar@pengutronix.de>, Pengutronix
+ */
+
+/dts-v1/;
+#include "imx53-tqma53.dtsi"
+
+/ {
+	model = "TQ MBa53 starter kit";
+	compatible = "tq,mba53", "tq,tqma53", "fsl,imx53";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm2 0 50000 0>;
+		brightness-levels = <0 24 28 32 36 40 44 48 52 56 60 64 68 72 76 80 84 88 92 96 100>;
+		default-brightness-level = <10>;
+		enable-gpios = <&gpio7 7 0>;
+		power-supply = <&reg_backlight>;
+	};
+
+	disp1: disp1 {
+		compatible = "fsl,imx-parallel-display";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_disp1_1>;
+		interface-pix-fmt = "rgb24";
+		status = "disabled";
+
+		port {
+			display1_in: endpoint {
+				remote-endpoint = <&ipu_di1_disp1>;
+			};
+		};
+	};
+
+	reg_backlight: regulator-backlight {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-supply";
+		gpio = <&gpio2 5 0>;
+		startup-delay-us = <5000>;
+	};
+
+	reg_3p2v: regulator-3p2v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P2V";
+		regulator-min-microvolt = <3200000>;
+		regulator-max-microvolt = <3200000>;
+		regulator-always-on;
+	};
+
+	sound {
+		compatible = "tq,imx53-mba53-sgtl5000",
+			     "fsl,imx-audio-sgtl5000";
+		model = "imx53-mba53-sgtl5000";
+		ssi-controller = <&ssi2>;
+		audio-codec = <&codec>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"Headphone Jack", "HP_OUT";
+		mux-int-port = <2>;
+		mux-ext-port = <5>;
+	};
+};
+
+&ldb {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lvds1_1>;
+	status = "disabled";
+};
+
+&iomuxc {
+	pinctrl_lvds1_1: lvds1-1-grp {
+		fsl,pins = <
+			MX53_PAD_LVDS0_TX3_P__LDB_LVDS0_TX3 0x80000000
+			MX53_PAD_LVDS0_CLK_P__LDB_LVDS0_CLK 0x80000000
+			MX53_PAD_LVDS0_TX2_P__LDB_LVDS0_TX2 0x80000000
+			MX53_PAD_LVDS0_TX1_P__LDB_LVDS0_TX1 0x80000000
+			MX53_PAD_LVDS0_TX0_P__LDB_LVDS0_TX0 0x80000000
+		>;
+	};
+
+	pinctrl_lvds1_2: lvds1-2-grp {
+		fsl,pins = <
+			MX53_PAD_LVDS1_TX3_P__LDB_LVDS1_TX3 0x80000000
+			MX53_PAD_LVDS1_TX2_P__LDB_LVDS1_TX2 0x80000000
+			MX53_PAD_LVDS1_CLK_P__LDB_LVDS1_CLK 0x80000000
+			MX53_PAD_LVDS1_TX1_P__LDB_LVDS1_TX1 0x80000000
+			MX53_PAD_LVDS1_TX0_P__LDB_LVDS1_TX0 0x80000000
+		>;
+	};
+
+	pinctrl_disp1_1: disp1-1-grp {
+		fsl,pins = <
+			MX53_PAD_EIM_A16__IPU_DI1_DISP_CLK 0x80000000 /* DISP1_CLK */
+			MX53_PAD_EIM_DA10__IPU_DI1_PIN15   0x80000000 /* DISP1_DRDY */
+			MX53_PAD_EIM_D23__IPU_DI1_PIN2     0x80000000 /* DISP1_HSYNC */
+			MX53_PAD_EIM_EB3__IPU_DI1_PIN3     0x80000000 /* DISP1_VSYNC */
+			MX53_PAD_EIM_D26__IPU_DISP1_DAT_22 0x80000000
+			MX53_PAD_EIM_D27__IPU_DISP1_DAT_23 0x80000000
+			MX53_PAD_EIM_D30__IPU_DISP1_DAT_21 0x80000000
+			MX53_PAD_EIM_D31__IPU_DISP1_DAT_20 0x80000000
+			MX53_PAD_EIM_A24__IPU_DISP1_DAT_19 0x80000000
+			MX53_PAD_EIM_A23__IPU_DISP1_DAT_18 0x80000000
+			MX53_PAD_EIM_A22__IPU_DISP1_DAT_17 0x80000000
+			MX53_PAD_EIM_A21__IPU_DISP1_DAT_16 0x80000000
+			MX53_PAD_EIM_A20__IPU_DISP1_DAT_15 0x80000000
+			MX53_PAD_EIM_A19__IPU_DISP1_DAT_14 0x80000000
+			MX53_PAD_EIM_A18__IPU_DISP1_DAT_13 0x80000000
+			MX53_PAD_EIM_A17__IPU_DISP1_DAT_12 0x80000000
+			MX53_PAD_EIM_EB0__IPU_DISP1_DAT_11 0x80000000
+			MX53_PAD_EIM_EB1__IPU_DISP1_DAT_10 0x80000000
+			MX53_PAD_EIM_DA0__IPU_DISP1_DAT_9  0x80000000
+			MX53_PAD_EIM_DA1__IPU_DISP1_DAT_8  0x80000000
+			MX53_PAD_EIM_DA2__IPU_DISP1_DAT_7  0x80000000
+			MX53_PAD_EIM_DA3__IPU_DISP1_DAT_6  0x80000000
+			MX53_PAD_EIM_DA4__IPU_DISP1_DAT_5  0x80000000
+			MX53_PAD_EIM_DA5__IPU_DISP1_DAT_4  0x80000000
+			MX53_PAD_EIM_DA6__IPU_DISP1_DAT_3  0x80000000
+			MX53_PAD_EIM_DA7__IPU_DISP1_DAT_2  0x80000000
+			MX53_PAD_EIM_DA8__IPU_DISP1_DAT_1  0x80000000
+			MX53_PAD_EIM_DA9__IPU_DISP1_DAT_0  0x80000000
+		>;
+	};
+
+	pinctrl_vga_sync_1: vgasync-1-grp {
+		fsl,pins = <
+			/* VGA_VSYNC, HSYNC with max drive strength */
+			MX53_PAD_EIM_CS1__IPU_DI1_PIN6	   0xe6
+			MX53_PAD_EIM_DA15__IPU_DI1_PIN4	   0xe6
+		>;
+	};
+};
+
+&ipu_di1_disp1 {
+	remote-endpoint = <&display1_in>;
+};
+
+&cspi {
+	status = "okay";
+};
+
+&audmux {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+};
+
+&i2c2 {
+	codec: sgtl5000@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		clocks = <&clks IMX5_CLK_SSI_EXT1_GATE>;
+		VDDA-supply = <&reg_3p2v>;
+		VDDIO-supply = <&reg_3p2v>;
+	};
+
+	expander: pca9554@20 {
+		compatible = "nxp,pca9554";
+		reg = <0x20>;
+		interrupts = <109>;
+		#gpio-cells = <2>;
+		gpio-controller;
+	};
+
+	sensor2: temperature-sensor@49 {
+		compatible = "national,lm75b";
+		reg = <0x49>;
+	};
+};
+
+&fec {
+	phy-reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&esdhc2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&ecspi1 {
+	status = "okay";
+};
+
+&usbotg {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&ssi2 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&can1 {
+	status = "okay";
+};
+
+&can2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&tve {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_vga_sync_1>;
+	ddc-i2c-bus = <&i2c3>;
+	fsl,tve-mode = "vga";
+	fsl,hsync-pin = <4>;
+	fsl,vsync-pin = <6>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx53-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx53-pinfunc.h
index 67bd06610fdf..67bd06610fdf 100644
--- a/arch/arm/boot/dts/imx53-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx53-pinfunc.h
diff --git a/arch/arm/boot/dts/imx53-ppd.dts b/arch/arm/boot/dts/nxp/imx/imx53-ppd.dts
index 37d0cffea99c..2892e457fea7 100644
--- a/arch/arm/boot/dts/imx53-ppd.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-ppd.dts
@@ -167,7 +167,7 @@
 
 	pwm_bl: backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm2 0 50000>;
+		pwms = <&pwm2 0 50000 0>;
 		brightness-levels = <0 2 5 7 10 12 15 17 20 22 25 28 30 33 35
 				     38 40 43 45 48 51 53 56 58 61 63 66 68 71
 				     73 76 79 81 84 86 89 91 94 96 99 102 104
@@ -187,7 +187,7 @@
 
 		led-1 {
 			label = "alarm-brightness";
-			pwms = <&pwm1 0 100000>;
+			pwms = <&pwm1 0 100000 0>;
 			max-brightness = <255>;
 		};
 	};
@@ -488,7 +488,7 @@
 	scl-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 
-	i2c-switch@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9547";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -593,7 +593,7 @@
 
 	touchscreen@4b {
 		compatible = "atmel,maxtouch";
-		reset-gpio = <&gpio5 19 GPIO_ACTIVE_LOW>;
+		reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>;
 		reg = <0x4b>;
 		interrupt-parent = <&gpio5>;
 		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
@@ -628,14 +628,12 @@
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
 };
 
 &pwm2 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm2>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/nxp/imx/imx53-qsb-common.dtsi b/arch/arm/boot/dts/nxp/imx/imx53-qsb-common.dtsi
new file mode 100644
index 000000000000..1869ad86baf2
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx53-qsb-common.dtsi
@@ -0,0 +1,406 @@
+// SPDX-License-Identifier: GPL-2.0+
+//
+// Copyright 2011 Freescale Semiconductor, Inc.
+// Copyright 2011 Linaro Ltd.
+
+#include "imx53.dtsi"
+
+/ {
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	memory@70000000 {
+		device_type = "memory";
+		reg = <0x70000000 0x20000000>,
+		      <0xb0000000 0x20000000>;
+	};
+
+	backlight_parallel: backlight-parallel {
+		compatible = "pwm-backlight";
+		pwms = <&pwm2 0 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <7>;
+	};
+
+	display0: disp0 {
+		compatible = "fsl,imx-parallel-display";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu_disp0>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+
+		port@0 {
+			reg = <0>;
+
+			display0_in: endpoint {
+				remote-endpoint = <&ipu_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			display_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-power {
+			label = "Power Button";
+			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			wakeup-source;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pin_gpio7_7>;
+
+		led-user {
+			label = "Heartbeat";
+			gpios = <&gpio7 7 0>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	panel_dpi: panel {
+		compatible = "sii,43wvf1g";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_display_power>;
+		backlight = <&backlight_parallel>;
+		enable-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
+	reg_3p2v: regulator-3p2v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P2V";
+		regulator-min-microvolt = <3200000>;
+		regulator-max-microvolt = <3200000>;
+		regulator-always-on;
+	};
+
+	reg_usb_vbus: regulator-usb-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio7 8 0>;
+		enable-active-high;
+	};
+
+	sound {
+		compatible = "fsl,imx53-qsb-sgtl5000",
+			     "fsl,imx-audio-sgtl5000";
+		model = "imx53-qsb-sgtl5000";
+		ssi-controller = <&ssi2>;
+		audio-codec = <&sgtl5000>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"Headphone Jack", "HP_OUT";
+		mux-int-port = <2>;
+		mux-ext-port = <5>;
+	};
+};
+
+&cpu0 {
+	/* CPU rated to 1GHz, not 1.2GHz as per the default settings */
+	operating-points = <
+		/* kHz   uV */
+		166666  850000
+		400000  900000
+		800000  1050000
+		1000000 1200000
+	>;
+};
+
+&esdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc1>;
+	cd-gpios = <&gpio3 13 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&ipu_di0_disp0 {
+	remote-endpoint = <&display0_in>;
+};
+
+&ssi2 {
+	status = "okay";
+};
+
+&esdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc3>;
+	cd-gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio3 12 GPIO_ACTIVE_HIGH>;
+	bus-width = <8>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX53_PAD_GPIO_8__GPIO1_8          0x80000000
+			MX53_PAD_PATA_DATA14__GPIO2_14    0x80000000
+			MX53_PAD_PATA_DATA15__GPIO2_15    0x80000000
+			MX53_PAD_EIM_DA11__GPIO3_11       0x80000000
+			MX53_PAD_EIM_DA12__GPIO3_12       0x80000000
+			MX53_PAD_PATA_DA_0__GPIO7_6       0x80000000
+			MX53_PAD_PATA_DA_2__GPIO7_8	  0x80000000
+			MX53_PAD_GPIO_16__GPIO7_11        0x80000000
+		>;
+	};
+
+	led_pin_gpio7_7: led_gpio7-7-grp {
+		fsl,pins = <
+			MX53_PAD_PATA_DA_1__GPIO7_7 0x80000000
+		>;
+	};
+
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX53_PAD_KEY_COL0__AUDMUX_AUD5_TXC	0x80000000
+			MX53_PAD_KEY_ROW0__AUDMUX_AUD5_TXD	0x80000000
+			MX53_PAD_KEY_COL1__AUDMUX_AUD5_TXFS	0x80000000
+			MX53_PAD_KEY_ROW1__AUDMUX_AUD5_RXD	0x80000000
+		>;
+	};
+
+	pinctrl_codec: codecgrp {
+		fsl,pins = <
+			MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK	0x1c4
+		>;
+	};
+
+	pinctrl_display_power: displaypowergrp {
+		fsl,pins = <
+			MX53_PAD_EIM_D24__GPIO3_24		0x1e4
+		>;
+	};
+
+	pinctrl_esdhc1: esdhc1grp {
+		fsl,pins = <
+			MX53_PAD_SD1_DATA0__ESDHC1_DAT0		0x1d5
+			MX53_PAD_SD1_DATA1__ESDHC1_DAT1		0x1d5
+			MX53_PAD_SD1_DATA2__ESDHC1_DAT2		0x1d5
+			MX53_PAD_SD1_DATA3__ESDHC1_DAT3		0x1d5
+			MX53_PAD_SD1_CMD__ESDHC1_CMD		0x1d5
+			MX53_PAD_SD1_CLK__ESDHC1_CLK		0x1d5
+			MX53_PAD_EIM_DA13__GPIO3_13		0xe4
+		>;
+	};
+
+	pinctrl_esdhc3: esdhc3grp {
+		fsl,pins = <
+			MX53_PAD_PATA_DATA8__ESDHC3_DAT0	0x1d5
+			MX53_PAD_PATA_DATA9__ESDHC3_DAT1	0x1d5
+			MX53_PAD_PATA_DATA10__ESDHC3_DAT2	0x1d5
+			MX53_PAD_PATA_DATA11__ESDHC3_DAT3	0x1d5
+			MX53_PAD_PATA_DATA0__ESDHC3_DAT4	0x1d5
+			MX53_PAD_PATA_DATA1__ESDHC3_DAT5	0x1d5
+			MX53_PAD_PATA_DATA2__ESDHC3_DAT6	0x1d5
+			MX53_PAD_PATA_DATA3__ESDHC3_DAT7	0x1d5
+			MX53_PAD_PATA_RESET_B__ESDHC3_CMD	0x1d5
+			MX53_PAD_PATA_IORDY__ESDHC3_CLK		0x1d5
+		>;
+	};
+
+	pinctrl_fec: fecgrp {
+		fsl,pins = <
+			MX53_PAD_FEC_MDC__FEC_MDC		0x4
+			MX53_PAD_FEC_MDIO__FEC_MDIO		0x1fc
+			MX53_PAD_FEC_REF_CLK__FEC_TX_CLK	0x180
+			MX53_PAD_FEC_RX_ER__FEC_RX_ER		0x180
+			MX53_PAD_FEC_CRS_DV__FEC_RX_DV		0x180
+			MX53_PAD_FEC_RXD1__FEC_RDATA_1		0x180
+			MX53_PAD_FEC_RXD0__FEC_RDATA_0		0x180
+			MX53_PAD_FEC_TX_EN__FEC_TX_EN		0x4
+			MX53_PAD_FEC_TXD1__FEC_TDATA_1		0x4
+			MX53_PAD_FEC_TXD0__FEC_TDATA_0		0x4
+		>;
+	};
+
+	/* open drain */
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX53_PAD_CSI0_DAT8__I2C1_SDA		0x400001ec
+			MX53_PAD_CSI0_DAT9__I2C1_SCL		0x400001ec
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX53_PAD_KEY_ROW3__I2C2_SDA		0xc0000000
+			MX53_PAD_KEY_COL3__I2C2_SCL		0xc0000000
+		>;
+	};
+
+	pinctrl_ipu_disp0: ipudisp0grp {
+		fsl,pins = <
+			MX53_PAD_DI0_DISP_CLK__IPU_DI0_DISP_CLK	0x5
+			MX53_PAD_DI0_PIN15__IPU_DI0_PIN15	0x5
+			MX53_PAD_DI0_PIN2__IPU_DI0_PIN2		0x5
+			MX53_PAD_DI0_PIN3__IPU_DI0_PIN3		0x5
+			MX53_PAD_DISP0_DAT0__IPU_DISP0_DAT_0	0x5
+			MX53_PAD_DISP0_DAT1__IPU_DISP0_DAT_1	0x5
+			MX53_PAD_DISP0_DAT2__IPU_DISP0_DAT_2	0x5
+			MX53_PAD_DISP0_DAT3__IPU_DISP0_DAT_3	0x5
+			MX53_PAD_DISP0_DAT4__IPU_DISP0_DAT_4	0x5
+			MX53_PAD_DISP0_DAT5__IPU_DISP0_DAT_5	0x5
+			MX53_PAD_DISP0_DAT6__IPU_DISP0_DAT_6	0x5
+			MX53_PAD_DISP0_DAT7__IPU_DISP0_DAT_7	0x5
+			MX53_PAD_DISP0_DAT8__IPU_DISP0_DAT_8	0x5
+			MX53_PAD_DISP0_DAT9__IPU_DISP0_DAT_9	0x5
+			MX53_PAD_DISP0_DAT10__IPU_DISP0_DAT_10	0x5
+			MX53_PAD_DISP0_DAT11__IPU_DISP0_DAT_11	0x5
+			MX53_PAD_DISP0_DAT12__IPU_DISP0_DAT_12	0x5
+			MX53_PAD_DISP0_DAT13__IPU_DISP0_DAT_13	0x5
+			MX53_PAD_DISP0_DAT14__IPU_DISP0_DAT_14	0x5
+			MX53_PAD_DISP0_DAT15__IPU_DISP0_DAT_15	0x5
+			MX53_PAD_DISP0_DAT16__IPU_DISP0_DAT_16	0x5
+			MX53_PAD_DISP0_DAT17__IPU_DISP0_DAT_17	0x5
+			MX53_PAD_DISP0_DAT18__IPU_DISP0_DAT_18	0x5
+			MX53_PAD_DISP0_DAT19__IPU_DISP0_DAT_19	0x5
+			MX53_PAD_DISP0_DAT20__IPU_DISP0_DAT_20	0x5
+			MX53_PAD_DISP0_DAT21__IPU_DISP0_DAT_21	0x5
+			MX53_PAD_DISP0_DAT22__IPU_DISP0_DAT_22	0x5
+			MX53_PAD_DISP0_DAT23__IPU_DISP0_DAT_23	0x5
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX53_PAD_GPIO_1__PWM2_PWMO		0x5
+		>;
+	};
+
+	pinctrl_vga_sync: vgasync-grp {
+		fsl,pins = <
+			/* VGA_HSYNC, VSYNC with max drive strength */
+			MX53_PAD_EIM_OE__IPU_DI1_PIN7 0xe6
+			MX53_PAD_EIM_RW__IPU_DI1_PIN8 0xe6
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX53_PAD_CSI0_DAT10__UART1_TXD_MUX	0x1e4
+			MX53_PAD_CSI0_DAT11__UART1_RXD_MUX	0x1e4
+		>;
+	};
+};
+
+&tve {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_vga_sync>;
+	ddc-i2c-bus = <&i2c2>;
+	fsl,tve-mode = "vga";
+	fsl,hsync-pin = <7>;	/* IPU DI1 PIN7 via EIM_OE */
+	fsl,vsync-pin = <8>;	/* IPU DI1 PIN8 via EIM_RW */
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	sgtl5000: codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_codec>;
+		#sound-dai-cells = <0>;
+		VDDA-supply = <&reg_3p2v>;
+		VDDIO-supply = <&reg_3p2v>;
+		clocks = <&clks IMX5_CLK_SSI_EXT1_GATE>;
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	accelerometer: mma8450@1c {
+		compatible = "fsl,mma8450";
+		reg = <0x1c>;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec>;
+	phy-mode = "rmii";
+	phy-reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&vpu {
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usb_vbus>;
+	phy_type = "utmi";
+	status = "okay";
+};
+
+&usbotg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx53-qsb-hdmi.dtso b/arch/arm/boot/dts/nxp/imx/imx53-qsb-hdmi.dtso
new file mode 100644
index 000000000000..2527bfe13145
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx53-qsb-hdmi.dtso
@@ -0,0 +1,83 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * DT overlay for MCIMXHDMICARD as used with the iMX53 QSB or QSRB boards
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/dts-v1/;
+/plugin/;
+
+&{/} {
+	hdmi: connector-hdmi {
+		compatible = "hdmi-connector";
+		label = "hdmi";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&sii9022_out>;
+			};
+		};
+	};
+
+	reg_1p2v: regulator-1p2v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P2V";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-always-on;
+		vin-supply = <&reg_3p2v>;
+	};
+};
+
+&display0 {
+	status = "okay";
+
+	port@1 {
+		display0_out: endpoint {
+			remote-endpoint = <&sii9022_in>;
+		};
+	};
+};
+
+&i2c2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	sii9022: bridge-hdmi@39 {
+		compatible = "sil,sii9022";
+		reg = <0x39>;
+		reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+		interrupts-extended = <&gpio3 31 IRQ_TYPE_LEVEL_LOW>;
+		iovcc-supply = <&reg_3p2v>;
+		#sound-dai-cells = <0>;
+		sil,i2s-data-lanes = <0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				sii9022_in: endpoint {
+					remote-endpoint = <&display0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				sii9022_out: endpoint {
+					remote-endpoint = <&hdmi_connector_in>;
+				};
+			};
+		};
+	};
+};
+
+&panel_dpi {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/imx53-qsb.dts b/arch/arm/boot/dts/nxp/imx/imx53-qsb.dts
index 6831836bd726..6831836bd726 100644
--- a/arch/arm/boot/dts/imx53-qsb.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-qsb.dts
diff --git a/arch/arm/boot/dts/imx53-qsrb.dts b/arch/arm/boot/dts/nxp/imx/imx53-qsrb.dts
index 1bbf24ad308a..2f06ad61a766 100644
--- a/arch/arm/boot/dts/imx53-qsrb.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-qsrb.dts
@@ -13,12 +13,10 @@
 };
 
 &iomuxc {
-	imx53-qsrb {
-		pinctrl_pmic: pmicgrp {
-			fsl,pins = <
-				MX53_PAD_CSI0_DAT5__GPIO5_23	0x1c4 /* IRQ */
-			>;
-		};
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			MX53_PAD_CSI0_DAT5__GPIO5_23	0x1c4 /* IRQ */
+		>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/nxp/imx/imx53-sk-imx53-atm0700d4-lvds.dts b/arch/arm/boot/dts/nxp/imx/imx53-sk-imx53-atm0700d4-lvds.dts
new file mode 100644
index 000000000000..b1c1e7c759b3
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx53-sk-imx53-atm0700d4-lvds.dts
@@ -0,0 +1,97 @@
+// SPDX-License-Identifier: GPL-2.0+
+//
+// Copyright 2023 Linaro Ltd.
+
+/dts-v1/;
+
+#include <dt-bindings/pwm/pwm.h>
+#include "imx53-sk-imx53-atm0700d4.dtsi"
+
+/ {
+	lvds-decoder {
+		compatible = "ti,sn65lvds94", "lvds-decoder";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lvds_decoder_in: endpoint {
+					remote-endpoint = <&lvds0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				lvds_decoder_out: endpoint {
+					remote-endpoint = <&panel_rgb_in>;
+				};
+			};
+		};
+	};
+};
+
+&iomuxc {
+	pinctrl_lvds0: lvds0grp {
+		/* LVDS pins only have pin mux configuration */
+		fsl,pins = <
+			MX53_PAD_LVDS0_CLK_P__LDB_LVDS0_CLK	0x80000000
+			MX53_PAD_LVDS0_TX0_P__LDB_LVDS0_TX0	0x80000000
+			MX53_PAD_LVDS0_TX1_P__LDB_LVDS0_TX1	0x80000000
+			MX53_PAD_LVDS0_TX2_P__LDB_LVDS0_TX2	0x80000000
+			MX53_PAD_LVDS0_TX3_P__LDB_LVDS0_TX3	0x80000000
+		>;
+	};
+
+	pinctrl_spi_gpio: spigrp {
+		fsl,pins = <
+			MX53_PAD_EIM_A22__GPIO2_16		0x1f4
+			MX53_PAD_EIM_A21__GPIO2_17		0x1f4
+			MX53_PAD_EIM_A16__GPIO2_22		0x1f4
+			MX53_PAD_EIM_A18__GPIO2_20		0x1f4
+		>;
+	};
+};
+
+&ldb {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lvds0>;
+	status = "okay";
+
+	lvds0: lvds-channel@0 {
+		reg = <0>;
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <24>;
+		status = "okay";
+
+		port@2 {
+			reg = <2>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&lvds_decoder_in>;
+			};
+		};
+	};
+};
+
+&panel_rgb_in {
+	remote-endpoint = <&lvds_decoder_out>;
+};
+
+&spi_ts {
+	pinctrl-0 = <&pinctrl_spi_gpio>;
+	pinctrl-names = "default";
+
+	sck-gpios = <&gpio2 16 GPIO_ACTIVE_HIGH>;
+	miso-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;
+	mosi-gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>;
+};
+
+&touchscreen {
+	interrupts-extended = <&gpio3 22 IRQ_TYPE_EDGE_BOTH>;
+	pendown-gpio = <&gpio3 22 GPIO_ACTIVE_LOW>;
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx53-sk-imx53-atm0700d4-rgb.dts b/arch/arm/boot/dts/nxp/imx/imx53-sk-imx53-atm0700d4-rgb.dts
new file mode 100644
index 000000000000..2559ada7e401
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx53-sk-imx53-atm0700d4-rgb.dts
@@ -0,0 +1,112 @@
+// SPDX-License-Identifier: GPL-2.0+
+//
+// Copyright 2023 Linaro Ltd.
+
+/dts-v1/;
+
+#include <dt-bindings/pwm/pwm.h>
+#include "imx53-sk-imx53-atm0700d4.dtsi"
+
+/ {
+	display: disp0 {
+		compatible = "fsl,imx-parallel-display";
+		interface-pix-fmt = "rgb24";
+		pinctrl-0 = <&pinctrl_rgb24>;
+		pinctrl-names = "default";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			display0_in: endpoint {
+				remote-endpoint = <&ipu_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			display_out: endpoint {
+				remote-endpoint = <&panel_rgb_in>;
+			};
+		};
+	};
+
+};
+
+&iomuxc {
+	pinctrl_rgb24: rgb24grp {
+		fsl,pins = <
+			MX53_PAD_DI0_DISP_CLK__IPU_DI0_DISP_CLK		0x5
+			MX53_PAD_DI0_PIN15__IPU_DI0_PIN15		0x5
+			MX53_PAD_DI0_PIN2__IPU_DI0_PIN2			0x5
+			MX53_PAD_DI0_PIN3__IPU_DI0_PIN3			0x5
+			MX53_PAD_DISP0_DAT0__IPU_DISP0_DAT_0		0x5
+			MX53_PAD_DISP0_DAT1__IPU_DISP0_DAT_1		0x5
+			MX53_PAD_DISP0_DAT2__IPU_DISP0_DAT_2		0x5
+			MX53_PAD_DISP0_DAT3__IPU_DISP0_DAT_3		0x5
+			MX53_PAD_DISP0_DAT4__IPU_DISP0_DAT_4		0x5
+			MX53_PAD_DISP0_DAT5__IPU_DISP0_DAT_5		0x5
+			MX53_PAD_DISP0_DAT6__IPU_DISP0_DAT_6		0x5
+			MX53_PAD_DISP0_DAT7__IPU_DISP0_DAT_7		0x5
+			MX53_PAD_DISP0_DAT8__IPU_DISP0_DAT_8		0x5
+			MX53_PAD_DISP0_DAT9__IPU_DISP0_DAT_9		0x5
+			MX53_PAD_DISP0_DAT10__IPU_DISP0_DAT_10		0x5
+			MX53_PAD_DISP0_DAT11__IPU_DISP0_DAT_11		0x5
+			MX53_PAD_DISP0_DAT12__IPU_DISP0_DAT_12		0x5
+			MX53_PAD_DISP0_DAT13__IPU_DISP0_DAT_13		0x5
+			MX53_PAD_DISP0_DAT14__IPU_DISP0_DAT_14		0x5
+			MX53_PAD_DISP0_DAT15__IPU_DISP0_DAT_15		0x5
+			MX53_PAD_DISP0_DAT16__IPU_DISP0_DAT_16		0x5
+			MX53_PAD_DISP0_DAT17__IPU_DISP0_DAT_17		0x5
+			MX53_PAD_DISP0_DAT18__IPU_DISP0_DAT_18		0x5
+			MX53_PAD_DISP0_DAT19__IPU_DISP0_DAT_19		0x5
+			MX53_PAD_DISP0_DAT20__IPU_DISP0_DAT_20		0x5
+			MX53_PAD_DISP0_DAT21__IPU_DISP0_DAT_21		0x5
+			MX53_PAD_DISP0_DAT22__IPU_DISP0_DAT_22		0x5
+			MX53_PAD_DISP0_DAT23__IPU_DISP0_DAT_23		0x5
+		>;
+	};
+
+	pinctrl_spi_gpio: spigrp {
+		fsl,pins = <
+			MX53_PAD_SD1_DATA1__GPIO1_17		0x1f4
+			MX53_PAD_GPIO_7__GPIO1_7		0x1f4
+			MX53_PAD_PATA_DATA3__GPIO2_3		0x1f4
+			MX53_PAD_PATA_DATA8__GPIO2_8		0x1f4
+		>;
+	};
+};
+
+&ipu_di0_disp0 {
+	remote-endpoint = <&display0_in>;
+};
+
+&panel {
+	enable-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+};
+
+&panel_rgb_in {
+	remote-endpoint = <&display_out>;
+};
+
+&pwm1 {
+	status = "disabled";
+};
+
+&spi_ts {
+	pinctrl-0 = <&pinctrl_spi_gpio>;
+	pinctrl-names = "default";
+
+	sck-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+	mosi-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+	miso-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+	cs-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>;
+};
+
+&touchscreen {
+	interrupts-extended = <&gpio2 6 IRQ_TYPE_EDGE_BOTH>;
+	pendown-gpio = <&gpio2 6 GPIO_ACTIVE_LOW>;
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx53-sk-imx53-atm0700d4.dtsi b/arch/arm/boot/dts/nxp/imx/imx53-sk-imx53-atm0700d4.dtsi
new file mode 100644
index 000000000000..e395004e80e6
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx53-sk-imx53-atm0700d4.dtsi
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: GPL-2.0+
+//
+// Copyright 2023 Linaro Ltd.
+
+/dts-v1/;
+
+#include <dt-bindings/pwm/pwm.h>
+#include "imx53-sk-imx53.dts"
+
+/ {
+	panel: panel-rgb {
+		compatible = "powertip,ph800480t013-idf02";
+
+		port {
+			panel_rgb_in: endpoint {
+			};
+		};
+	};
+
+	spi_ts: spi {
+		compatible = "spi-gpio";
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+
+		num-chipselects = <1>;
+
+		touchscreen: touchscreen@0 {
+			reg = <0>;
+			compatible = "ti,ads7843";
+			spi-max-frequency = <300000>;
+
+			ti,vref-mv = /bits/ 16 <3300>;
+			ti,x-plate-ohms = /bits/ 16 <450>;
+			ti,y-plate-ohms = /bits/ 16 <250>;
+			ti,debounce-tol = /bits/ 16 <10>;
+			ti,debounce-rep = /bits/ 16 <0>;
+			touchscreen-size-x = <4096>;
+			touchscreen-size-y = <4096>;
+			touchscreen-swapped-x-y;
+			touchscreen-max-pressure = <100>;
+
+			wakeup-source;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx53-sk-imx53.dts b/arch/arm/boot/dts/nxp/imx/imx53-sk-imx53.dts
new file mode 100644
index 000000000000..1a00d290092a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx53-sk-imx53.dts
@@ -0,0 +1,367 @@
+// SPDX-License-Identifier: GPL-2.0+
+//
+// Copyright 2023 Linaro Ltd.
+
+/dts-v1/;
+
+#include "imx53.dtsi"
+
+/ {
+	model = "StarterKit SK-iMX53 Board";
+	compatible = "starterkit,sk-imx53", "fsl,imx53";
+
+	aliases {
+		/*
+		 * iMX RTC is not battery powered on this board.
+		 * Use the i2c RTC as rtc0.
+		 */
+		rtc0 = &rtc;
+		rtc1 = &srtc;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	memory@70000000 {
+		device_type = "memory";
+		/* v2 had only 256 MB, v3 has 512 MB */
+		reg = <0x70000000 0x20000000>;
+	};
+
+	reg_usb1_vbus: regulator-usb-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio2 29 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usb_otg_vbus: regulator-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio2 24 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	status = "okay";
+};
+
+&cpu0 {
+	/* CPU rated to 800 MHz, not the default 1.2GHz. */
+	operating-points = <
+		/* kHz   uV */
+		166666  850000
+		400000  900000
+		800000  1050000
+	>;
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	cs-gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&esdhc1 {
+	cd-gpios = <&gpio3 14 GPIO_ACTIVE_LOW>;
+	fsl,wp-controller;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc1>;
+	status = "okay";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec>;
+	phy-mode = "rmii";
+	phy-handle = <&phy0>;
+	mac-address = [000000000000]; /* placeholder; will be overwritten by bootloader */
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+			reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	sda-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+	scl-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+
+	tlv320aic23: codec@1a {
+		compatible = "ti,tlv320aic23";
+		reg = <0x1a>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_codec>;
+		#sound-dai-cells = <0>;
+	};
+
+	rtc: rtc@68 {
+		compatible = "dallas,ds1338";
+		reg = <0x68>;
+	};
+};
+
+&iomuxc {
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX53_PAD_SD2_DATA3__AUDMUX_AUD4_TXC	0x1e4
+			MX53_PAD_SD2_DATA2__AUDMUX_AUD4_TXD	0x1e4
+			MX53_PAD_SD2_DATA1__AUDMUX_AUD4_TXFS	0x1e4
+			MX53_PAD_SD2_DATA0__AUDMUX_AUD4_RXD	0x1e4
+		>;
+	};
+
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX53_PAD_PATA_INTRQ__CAN1_TXCAN		0x1e4
+			MX53_PAD_PATA_DIOR__CAN1_RXCAN		0x1e4
+		>;
+	};
+
+	pinctrl_codec: codecgrp {
+		fsl,pins = <
+			MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK	0x1c4
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX53_PAD_EIM_D16__ECSPI1_SCLK		0x1e4
+			MX53_PAD_EIM_D17__ECSPI1_MISO		0x1e4
+			MX53_PAD_EIM_D18__ECSPI1_MOSI		0x1e4
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX53_PAD_CSI0_DAT9__ECSPI2_MOSI		0x1e4
+			MX53_PAD_CSI0_DAT10__ECSPI2_MISO	0x1e4
+			MX53_PAD_EIM_CS0__ECSPI2_SCLK		0x1e4
+		>;
+	};
+
+	pinctrl_esdhc1: esdhc1grp {
+		fsl,pins = <
+			MX53_PAD_SD1_DATA0__ESDHC1_DAT0		0x1d5
+			MX53_PAD_SD1_DATA1__ESDHC1_DAT1		0x1d5
+			MX53_PAD_SD1_DATA2__ESDHC1_DAT2		0x1d5
+			MX53_PAD_SD1_DATA3__ESDHC1_DAT3		0x1d5
+			MX53_PAD_SD1_CMD__ESDHC1_CMD		0x1d5
+			MX53_PAD_SD1_CLK__ESDHC1_CLK		0x1d5
+			MX53_PAD_EIM_DA14__GPIO3_14		0x1f0
+		>;
+	};
+
+	pinctrl_fec: fecgrp {
+		fsl,pins = <
+			MX53_PAD_FEC_MDC__FEC_MDC		0x1e4
+			MX53_PAD_FEC_MDIO__FEC_MDIO		0x1e4
+			MX53_PAD_FEC_REF_CLK__FEC_TX_CLK	0x1e4
+			MX53_PAD_FEC_RX_ER__FEC_RX_ER		0x1e4
+			MX53_PAD_FEC_CRS_DV__FEC_RX_DV		0x1e4
+			MX53_PAD_FEC_RXD1__FEC_RDATA_1		0x1e4
+			MX53_PAD_FEC_RXD0__FEC_RDATA_0		0x1e4
+			MX53_PAD_FEC_TX_EN__FEC_TX_EN		0x1c4
+			MX53_PAD_FEC_TXD1__FEC_TDATA_1		0x1e4
+			MX53_PAD_FEC_TXD0__FEC_TDATA_0		0x1e4
+			MX53_PAD_GPIO_1__GPIO1_1		0x1c4
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX53_PAD_EIM_D21__I2C1_SCL		0x400001e4
+			MX53_PAD_EIM_D28__I2C1_SDA		0x400001e4
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX53_PAD_KEY_ROW3__I2C2_SDA             0x400001e4
+			MX53_PAD_EIM_EB2__I2C2_SCL		0x400001e4
+		>;
+	};
+
+	pinctrl_i2c2_gpio: i2c2gpiogrp {
+		fsl,pins = <
+			MX53_PAD_KEY_ROW3__GPIO4_13		0x1e4
+			MX53_PAD_EIM_EB2__GPIO2_30		0x1e4
+		>;
+	};
+
+	pinctrl_nand: nandgrp {
+		fsl,pins = <
+			MX53_PAD_NANDF_WE_B__EMI_NANDF_WE_B	0x4
+			MX53_PAD_NANDF_RE_B__EMI_NANDF_RE_B	0x4
+			MX53_PAD_NANDF_CLE__EMI_NANDF_CLE	0x4
+			MX53_PAD_NANDF_ALE__EMI_NANDF_ALE	0x4
+			MX53_PAD_NANDF_WP_B__EMI_NANDF_WP_B	0xe0
+			MX53_PAD_NANDF_RB0__EMI_NANDF_RB_0	0xe0
+			MX53_PAD_NANDF_CS0__EMI_NANDF_CS_0	0x4
+			MX53_PAD_NANDF_CS1__EMI_NANDF_CS_1	0x4
+			MX53_PAD_NANDF_CS2__EMI_NANDF_CS_2	0x4
+			MX53_PAD_NANDF_CS3__EMI_NANDF_CS_3	0x4
+			MX53_PAD_EIM_DA0__EMI_NAND_WEIM_DA_0	0xa4
+			MX53_PAD_EIM_DA1__EMI_NAND_WEIM_DA_1	0xa4
+			MX53_PAD_EIM_DA2__EMI_NAND_WEIM_DA_2	0xa4
+			MX53_PAD_EIM_DA3__EMI_NAND_WEIM_DA_3	0xa4
+			MX53_PAD_EIM_DA4__EMI_NAND_WEIM_DA_4	0xa4
+			MX53_PAD_EIM_DA5__EMI_NAND_WEIM_DA_5	0xa4
+			MX53_PAD_EIM_DA6__EMI_NAND_WEIM_DA_6	0xa4
+			MX53_PAD_EIM_DA7__EMI_NAND_WEIM_DA_7	0xa4
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX53_PAD_GPIO_9__PWM1_PWMO		0x5
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX53_PAD_PATA_DIOW__UART1_TXD_MUX	0x1e4
+			MX53_PAD_PATA_DMACK__UART1_RXD_MUX	0x1e4
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX53_PAD_EIM_D24__UART3_TXD_MUX		0x1e4
+			MX53_PAD_EIM_D25__UART3_RXD_MUX		0x1e4
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX53_PAD_KEY_COL0__UART4_TXD_MUX	0x1e4
+			MX53_PAD_KEY_ROW0__UART4_RXD_MUX	0x1e4
+		>;
+	};
+};
+
+&nfc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_nand>;
+	nand-bus-width = <8>;
+	status = "okay";
+
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "boot";
+			reg = <0x00000000 0x00100000>;
+			read-only;
+		};
+
+		partition@100000 {
+			label = "u-boot";
+			reg = <0x00100000 0x00100000>;
+			read-only;
+		};
+
+		partition@200000 {
+			label = "u-boot-env";
+			reg = <0x00200000 0x00100000>;
+			read-only;
+		};
+
+		partition@1000000 {
+			label = "kernel-safe";
+			reg = <0x01000000 0x00a00000>;
+			read-only;
+		};
+
+		partition@1a00000 {
+			label = "kernel";
+			reg = <0x01a00000 0x005e0000>;
+		};
+
+		partition@2000000 {
+			label = "ubifs";
+			reg = <0x02000000 0x0e000000>;
+		};
+	};
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usb1_vbus>;
+	phy_type = "utmi";
+	disable-over-current;
+	status = "okay";
+};
+
+&usbotg {
+	dr_mode = "peripheral";
+	disable-over-current;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx53-smd.dts b/arch/arm/boot/dts/nxp/imx/imx53-smd.dts
new file mode 100644
index 000000000000..386371c816f4
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx53-smd.dts
@@ -0,0 +1,344 @@
+// SPDX-License-Identifier: GPL-2.0+
+//
+// Copyright 2011 Freescale Semiconductor, Inc.
+// Copyright 2011 Linaro Ltd.
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include "imx53.dtsi"
+
+/ {
+	model = "Freescale i.MX53 Smart Mobile Reference Design Board";
+	compatible = "fsl,imx53-smd", "fsl,imx53";
+
+	memory@70000000 {
+		device_type = "memory";
+		reg = <0x70000000 0x40000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio2 14 0>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio2 15 0>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+	};
+};
+
+&esdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc1>;
+	cd-gpios = <&gpio3 13 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio4 11 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&esdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc2>;
+	non-removable;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>, <&gpio3 19 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	zigbee: mc1323@0 {
+		compatible = "fsl,mc1323";
+		spi-max-frequency = <8000000>;
+		reg = <0>;
+	};
+
+	flash: flash@1 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "st,m25p32", "jedec,spi-nor";
+		spi-max-frequency = <20000000>;
+		reg = <1>;
+
+		partition@0 {
+			label = "U-Boot";
+			reg = <0x0 0x40000>;
+			read-only;
+		};
+
+		partition@40000 {
+			label = "Kernel";
+			reg = <0x40000 0x3c0000>;
+		};
+	};
+};
+
+&esdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc3>;
+	non-removable;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX53_PAD_PATA_DATA14__GPIO2_14 0x80000000
+			MX53_PAD_PATA_DATA15__GPIO2_15 0x80000000
+			MX53_PAD_EIM_EB2__GPIO2_30     0x80000000
+			MX53_PAD_EIM_DA13__GPIO3_13    0x80000000
+			MX53_PAD_EIM_D19__GPIO3_19     0x80000000
+			MX53_PAD_KEY_ROW2__GPIO4_11    0x80000000
+			MX53_PAD_PATA_DA_0__GPIO7_6    0x80000000
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX53_PAD_EIM_D16__ECSPI1_SCLK		0x80000000
+			MX53_PAD_EIM_D17__ECSPI1_MISO		0x80000000
+			MX53_PAD_EIM_D18__ECSPI1_MOSI		0x80000000
+		>;
+	};
+
+	pinctrl_esdhc1: esdhc1grp {
+		fsl,pins = <
+			MX53_PAD_SD1_DATA0__ESDHC1_DAT0		0x1d5
+			MX53_PAD_SD1_DATA1__ESDHC1_DAT1		0x1d5
+			MX53_PAD_SD1_DATA2__ESDHC1_DAT2		0x1d5
+			MX53_PAD_SD1_DATA3__ESDHC1_DAT3		0x1d5
+			MX53_PAD_SD1_CMD__ESDHC1_CMD		0x1d5
+			MX53_PAD_SD1_CLK__ESDHC1_CLK		0x1d5
+		>;
+	};
+
+	pinctrl_esdhc2: esdhc2grp {
+		fsl,pins = <
+			MX53_PAD_SD2_CMD__ESDHC2_CMD		0x1d5
+			MX53_PAD_SD2_CLK__ESDHC2_CLK		0x1d5
+			MX53_PAD_SD2_DATA0__ESDHC2_DAT0		0x1d5
+			MX53_PAD_SD2_DATA1__ESDHC2_DAT1		0x1d5
+			MX53_PAD_SD2_DATA2__ESDHC2_DAT2		0x1d5
+			MX53_PAD_SD2_DATA3__ESDHC2_DAT3		0x1d5
+		>;
+	};
+
+	pinctrl_esdhc3: esdhc3grp {
+		fsl,pins = <
+			MX53_PAD_PATA_DATA8__ESDHC3_DAT0	0x1d5
+			MX53_PAD_PATA_DATA9__ESDHC3_DAT1	0x1d5
+			MX53_PAD_PATA_DATA10__ESDHC3_DAT2	0x1d5
+			MX53_PAD_PATA_DATA11__ESDHC3_DAT3	0x1d5
+			MX53_PAD_PATA_DATA0__ESDHC3_DAT4	0x1d5
+			MX53_PAD_PATA_DATA1__ESDHC3_DAT5	0x1d5
+			MX53_PAD_PATA_DATA2__ESDHC3_DAT6	0x1d5
+			MX53_PAD_PATA_DATA3__ESDHC3_DAT7	0x1d5
+			MX53_PAD_PATA_RESET_B__ESDHC3_CMD	0x1d5
+			MX53_PAD_PATA_IORDY__ESDHC3_CLK		0x1d5
+		>;
+	};
+
+	pinctrl_fec: fecgrp {
+		fsl,pins = <
+			MX53_PAD_FEC_MDC__FEC_MDC		0x80000000
+			MX53_PAD_FEC_MDIO__FEC_MDIO		0x80000000
+			MX53_PAD_FEC_REF_CLK__FEC_TX_CLK	0x80000000
+			MX53_PAD_FEC_RX_ER__FEC_RX_ER		0x80000000
+			MX53_PAD_FEC_CRS_DV__FEC_RX_DV		0x80000000
+			MX53_PAD_FEC_RXD1__FEC_RDATA_1		0x80000000
+			MX53_PAD_FEC_RXD0__FEC_RDATA_0		0x80000000
+			MX53_PAD_FEC_TX_EN__FEC_TX_EN		0x80000000
+			MX53_PAD_FEC_TXD1__FEC_TDATA_1		0x80000000
+			MX53_PAD_FEC_TXD0__FEC_TDATA_0		0x80000000
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX53_PAD_CSI0_DAT8__I2C1_SDA		0xc0000000
+			MX53_PAD_CSI0_DAT9__I2C1_SCL		0xc0000000
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX53_PAD_KEY_ROW3__I2C2_SDA		0xc0000000
+			MX53_PAD_KEY_COL3__I2C2_SCL		0xc0000000
+		>;
+	};
+
+	pinctrl_ipu_csi0: ipucsi0grp {
+		fsl,pins = <
+			MX53_PAD_CSI0_DAT12__IPU_CSI0_D_12    0x1c4
+			MX53_PAD_CSI0_DAT13__IPU_CSI0_D_13    0x1c4
+			MX53_PAD_CSI0_DAT14__IPU_CSI0_D_14    0x1c4
+			MX53_PAD_CSI0_DAT15__IPU_CSI0_D_15    0x1c4
+			MX53_PAD_CSI0_DAT16__IPU_CSI0_D_16    0x1c4
+			MX53_PAD_CSI0_DAT17__IPU_CSI0_D_17    0x1c4
+			MX53_PAD_CSI0_DAT18__IPU_CSI0_D_18    0x1c4
+			MX53_PAD_CSI0_DAT19__IPU_CSI0_D_19    0x1c4
+			MX53_PAD_CSI0_PIXCLK__IPU_CSI0_PIXCLK 0x1e4
+			MX53_PAD_CSI0_VSYNC__IPU_CSI0_VSYNC   0x1e4
+			MX53_PAD_CSI0_MCLK__IPU_CSI0_HSYNC    0x1e4
+			MX53_PAD_CSI0_DATA_EN__IPU_CSI0_DATA_EN 0x1e4
+		>;
+	};
+
+	pinctrl_ov5642: ov5642grp {
+		fsl,pins = <
+			MX53_PAD_NANDF_WP_B__GPIO6_9   0x1e4
+			MX53_PAD_NANDF_RB0__GPIO6_10   0x1e4
+			MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK 0x1c4
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX53_PAD_CSI0_DAT10__UART1_TXD_MUX	0x1e4
+			MX53_PAD_CSI0_DAT11__UART1_RXD_MUX	0x1e4
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX	0x1e4
+			MX53_PAD_PATA_DMARQ__UART2_TXD_MUX	0x1e4
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX53_PAD_PATA_CS_0__UART3_TXD_MUX	0x1e4
+			MX53_PAD_PATA_CS_1__UART3_RXD_MUX	0x1e4
+			MX53_PAD_PATA_DA_1__UART3_CTS		0x1e4
+			MX53_PAD_PATA_DA_2__UART3_RTS		0x1e4
+		>;
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	codec: sgtl5000@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+	};
+
+	magnetometer: mag3110@e {
+		compatible = "fsl,mag3110";
+		reg = <0x0e>;
+	};
+
+	touchkey: mpr121@5a {
+		compatible = "fsl,mpr121";
+		reg = <0x5a>;
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	accelerometer: mma8450@1c {
+		compatible = "fsl,mma8450";
+		reg = <0x1c>;
+	};
+
+	camera: ov5642@3c {
+		compatible = "ovti,ov5642";
+		reg = <0x3c>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ov5642>;
+		assigned-clocks = <&clks IMX5_CLK_SSI_EXT1_SEL>,
+				  <&clks IMX5_CLK_SSI_EXT1_COM_SEL>;
+		assigned-clock-parents = <&clks IMX5_CLK_PLL2_SW>,
+					 <&clks IMX5_CLK_SSI_EXT1_PODF>;
+		assigned-clock-rates = <0>, <24000000>;
+		clocks = <&clks IMX5_CLK_SSI_EXT1_GATE>;
+		clock-names = "xclk";
+		DVDD-supply = <&ldo9_reg>;
+		AVDD-supply = <&ldo7_reg>;
+		reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>;
+		powerdown-gpios = <&gpio6 10 GPIO_ACTIVE_HIGH>;
+
+		port {
+			ov5642_to_ipu_csi0: endpoint {
+				remote-endpoint = <&ipu_csi0_from_parallel_sensor>;
+				bus-width = <8>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+			};
+		};
+	};
+
+	pmic: dialog@48 {
+		compatible = "dlg,da9053", "dlg,da9052";
+		reg = <0x48>;
+		interrupt-parent = <&gpio7>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+
+		regulators {
+			ldo7_reg: ldo7 {
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3600000>;
+			};
+
+			ldo9_reg: ldo9 {
+				regulator-min-microvolt = <1250000>;
+				regulator-max-microvolt = <3650000>;
+			};
+		};
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec>;
+	phy-mode = "rmii";
+	phy-reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&ipu_csi0_from_parallel_sensor {
+	remote-endpoint = <&ov5642_to_ipu_csi0>;
+	data-shift = <12>; /* Lines 19:12 used */
+	hsync-active = <1>;
+	vsync-active = <1>;
+};
+
+&ipu_csi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ipu_csi0>;
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx53-tqma53.dtsi b/arch/arm/boot/dts/nxp/imx/imx53-tqma53.dtsi
new file mode 100644
index 000000000000..0f0245df380f
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx53-tqma53.dtsi
@@ -0,0 +1,272 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 Sascha Hauer <s.hauer@pengutronix.de>, Pengutronix
+ * Copyright 2012 Steffen Trumtrar <s.trumtrar@pengutronix.de>, Pengutronix
+ */
+
+#include "imx53.dtsi"
+
+/ {
+	model = "TQ TQMa53";
+	compatible = "tq,tqma53", "fsl,imx53";
+
+	memory@70000000 {
+		device_type = "memory";
+		reg = <0x70000000 0x40000000>; /* Up to 1GiB */
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+};
+
+&esdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc2>,
+		    <&pinctrl_esdhc2_cdwp>;
+	vmmc-supply = <&reg_3p3v>;
+	wp-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+	status = "disabled";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "disabled";
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>, <&gpio3 19 GPIO_ACTIVE_LOW>,
+		   <&gpio3 24 GPIO_ACTIVE_LOW>, <&gpio3 25 GPIO_ACTIVE_LOW>;
+	status = "disabled";
+};
+
+&esdhc3 { /* EMMC */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc3>;
+	vmmc-supply = <&reg_3p3v>;
+	non-removable;
+	bus-width = <8>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			 MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK 0x80000000 /* SSI_MCLK */
+			 MX53_PAD_PATA_DA_1__GPIO7_7     0x80000000 /* LCD_BLT_EN */
+			 MX53_PAD_PATA_DA_2__GPIO7_8     0x80000000 /* LCD_RESET */
+			 MX53_PAD_PATA_DATA5__GPIO2_5    0x80000000 /* LCD_POWER */
+			 MX53_PAD_PATA_DATA6__GPIO2_6    0x80000000 /* PMIC_INT */
+			 MX53_PAD_PATA_DATA14__GPIO2_14  0x80000000 /* CSI_RST */
+			 MX53_PAD_PATA_DATA15__GPIO2_15  0x80000000 /* CSI_PWDN */
+			 MX53_PAD_GPIO_19__GPIO4_5 	 0x80000000 /* #SYSTEM_DOWN */
+			 MX53_PAD_GPIO_3__GPIO1_3        0x80000000
+			 MX53_PAD_PATA_DA_0__GPIO7_6	 0x80000000 /* #PHY_RESET */
+			 MX53_PAD_GPIO_1__PWM2_PWMO	 0x80000000 /* LCD_CONTRAST */
+		>;
+	};
+
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX53_PAD_KEY_COL0__AUDMUX_AUD5_TXC	0x80000000
+			MX53_PAD_KEY_ROW0__AUDMUX_AUD5_TXD	0x80000000
+			MX53_PAD_KEY_COL1__AUDMUX_AUD5_TXFS	0x80000000
+			MX53_PAD_KEY_ROW1__AUDMUX_AUD5_RXD	0x80000000
+		>;
+	};
+
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX53_PAD_KEY_COL2__CAN1_TXCAN		0x80000000
+			MX53_PAD_KEY_ROW2__CAN1_RXCAN		0x80000000
+		>;
+	};
+
+	pinctrl_can2: can2grp {
+		fsl,pins = <
+			MX53_PAD_KEY_COL4__CAN2_TXCAN		0x80000000
+			MX53_PAD_KEY_ROW4__CAN2_RXCAN		0x80000000
+		>;
+	};
+
+	pinctrl_cspi: cspigrp {
+		fsl,pins = <
+			MX53_PAD_SD1_DATA0__CSPI_MISO		0x1d5
+			MX53_PAD_SD1_CMD__CSPI_MOSI		0x1d5
+			MX53_PAD_SD1_CLK__CSPI_SCLK		0x1d5
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX53_PAD_EIM_D16__ECSPI1_SCLK		0x80000000
+			MX53_PAD_EIM_D17__ECSPI1_MISO		0x80000000
+			MX53_PAD_EIM_D18__ECSPI1_MOSI		0x80000000
+		>;
+	};
+
+	pinctrl_esdhc2: esdhc2grp {
+		fsl,pins = <
+			MX53_PAD_SD2_CMD__ESDHC2_CMD		0x1d5
+			MX53_PAD_SD2_CLK__ESDHC2_CLK		0x1d5
+			MX53_PAD_SD2_DATA0__ESDHC2_DAT0		0x1d5
+			MX53_PAD_SD2_DATA1__ESDHC2_DAT1		0x1d5
+			MX53_PAD_SD2_DATA2__ESDHC2_DAT2		0x1d5
+			MX53_PAD_SD2_DATA3__ESDHC2_DAT3		0x1d5
+		>;
+	};
+
+	pinctrl_esdhc2_cdwp: esdhc2cdwpgrp {
+		fsl,pins = <
+			MX53_PAD_GPIO_4__GPIO1_4	0x80000000 /* SD2_CD */
+			MX53_PAD_GPIO_2__GPIO1_2	0x80000000 /* SD2_WP */
+		>;
+	};
+
+	pinctrl_esdhc3: esdhc3grp {
+		fsl,pins = <
+			MX53_PAD_PATA_DATA8__ESDHC3_DAT0	0x1d5
+			MX53_PAD_PATA_DATA9__ESDHC3_DAT1	0x1d5
+			MX53_PAD_PATA_DATA10__ESDHC3_DAT2	0x1d5
+			MX53_PAD_PATA_DATA11__ESDHC3_DAT3	0x1d5
+			MX53_PAD_PATA_DATA0__ESDHC3_DAT4	0x1d5
+			MX53_PAD_PATA_DATA1__ESDHC3_DAT5	0x1d5
+			MX53_PAD_PATA_DATA2__ESDHC3_DAT6	0x1d5
+			MX53_PAD_PATA_DATA3__ESDHC3_DAT7	0x1d5
+			MX53_PAD_PATA_RESET_B__ESDHC3_CMD	0x1d5
+			MX53_PAD_PATA_IORDY__ESDHC3_CLK		0x1d5
+		>;
+	};
+
+	pinctrl_fec: fecgrp {
+		fsl,pins = <
+			MX53_PAD_FEC_MDC__FEC_MDC		0x80000000
+			MX53_PAD_FEC_MDIO__FEC_MDIO		0x80000000
+			MX53_PAD_FEC_REF_CLK__FEC_TX_CLK	0x80000000
+			MX53_PAD_FEC_RX_ER__FEC_RX_ER		0x80000000
+			MX53_PAD_FEC_CRS_DV__FEC_RX_DV		0x80000000
+			MX53_PAD_FEC_RXD1__FEC_RDATA_1		0x80000000
+			MX53_PAD_FEC_RXD0__FEC_RDATA_0		0x80000000
+			MX53_PAD_FEC_TX_EN__FEC_TX_EN		0x80000000
+			MX53_PAD_FEC_TXD1__FEC_TDATA_1		0x80000000
+			MX53_PAD_FEC_TXD0__FEC_TDATA_0		0x80000000
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX53_PAD_KEY_ROW3__I2C2_SDA		0xc0000000
+			MX53_PAD_KEY_COL3__I2C2_SCL		0xc0000000
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX53_PAD_GPIO_6__I2C3_SDA		0xc0000000
+			MX53_PAD_GPIO_5__I2C3_SCL		0xc0000000
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX53_PAD_PATA_DIOW__UART1_TXD_MUX	0x1e4
+			MX53_PAD_PATA_DMACK__UART1_RXD_MUX	0x1e4
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX	0x1e4
+			MX53_PAD_PATA_DMARQ__UART2_TXD_MUX	0x1e4
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX53_PAD_PATA_CS_0__UART3_TXD_MUX	0x1e4
+			MX53_PAD_PATA_CS_1__UART3_RXD_MUX	0x1e4
+		>;
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	uart-has-rtscts;
+	status = "disabled";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "disabled";
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	status = "disabled";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can2>;
+	status = "disabled";
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "disabled";
+};
+
+&cspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_cspi>;
+	cs-gpios = <&gpio1 18 GPIO_ACTIVE_LOW>, <&gpio1 19 GPIO_ACTIVE_LOW>,
+		   <&gpio1 21 GPIO_ACTIVE_LOW>;
+	status = "disabled";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	pmic: mc34708@8 {
+		compatible = "fsl,mc34708";
+		reg = <0x8>;
+		fsl,mc13xxx-uses-rtc;
+		interrupt-parent = <&gpio2>;
+		interrupts = <6 4>; /* PATA_DATA6, active high */
+	};
+
+	sensor1: temperature-sensor@48 {
+		compatible = "national,lm75b";
+		reg = <0x48>;
+	};
+
+	eeprom: eeprom@50 {
+		compatible = "atmel,24c64";
+		pagesize = <32>;
+		reg = <0x50>;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec>;
+	phy-mode = "rmii";
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/imx53-tx53-x03x.dts b/arch/arm/boot/dts/nxp/imx/imx53-tx53-x03x.dts
index a7f77527269d..872cf7e16f20 100644
--- a/arch/arm/boot/dts/imx53-tx53-x03x.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-tx53-x03x.dts
@@ -1,42 +1,6 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
 /*
  * Copyright 2013-2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 /dts-v1/;
@@ -67,7 +31,7 @@
 		};
 
 		display-timings {
-			VGA {
+			timing-vga {
 				clock-frequency = <25200000>;
 				hactive = <640>;
 				vactive = <480>;
@@ -83,7 +47,7 @@
 				pixelclk-active = <0>;
 			};
 
-			ETV570 {
+			timing-etc570 {
 				clock-frequency = <25200000>;
 				hactive = <640>;
 				vactive = <480>;
@@ -99,7 +63,7 @@
 				pixelclk-active = <0>;
 			};
 
-			ET0350 {
+			timing-et0350 {
 				clock-frequency = <6413760>;
 				hactive = <320>;
 				vactive = <240>;
@@ -115,7 +79,7 @@
 				pixelclk-active = <0>;
 			};
 
-			ET0430 {
+			timing-et0430 {
 				clock-frequency = <9009000>;
 				hactive = <480>;
 				vactive = <272>;
@@ -131,7 +95,7 @@
 				pixelclk-active = <1>;
 			};
 
-			ET0500 {
+			timing-et0500 {
 				clock-frequency = <33264000>;
 				hactive = <800>;
 				vactive = <480>;
@@ -147,7 +111,7 @@
 				pixelclk-active = <0>;
 			};
 
-			ET0700 { /* same as ET0500 */
+			timing-et0700 { /* same as ET0500 */
 				clock-frequency = <33264000>;
 				hactive = <800>;
 				vactive = <480>;
@@ -163,7 +127,7 @@
 				pixelclk-active = <0>;
 			};
 
-			ETQ570 {
+			timing-etq570 {
 				clock-frequency = <6596040>;
 				hactive = <320>;
 				vactive = <240>;
@@ -262,66 +226,64 @@
 };
 
 &iomuxc {
-	imx53-tx53-x03x {
-		pinctrl_edt_ft5x06_1: edt-ft5x06grp-1 {
-			fsl,pins = <
-				MX53_PAD_NANDF_CS2__GPIO6_15 0x1f0 /* Interrupt */
-				MX53_PAD_EIM_A16__GPIO2_22   0x04 /* Reset */
-				MX53_PAD_EIM_A17__GPIO2_21   0x04 /* Wake */
-			>;
-		};
+	pinctrl_edt_ft5x06_1: edt-ft5x06-1-grp {
+		fsl,pins = <
+			MX53_PAD_NANDF_CS2__GPIO6_15 0x1f0 /* Interrupt */
+			MX53_PAD_EIM_A16__GPIO2_22   0x04 /* Reset */
+			MX53_PAD_EIM_A17__GPIO2_21   0x04 /* Wake */
+		>;
+	};
 
-		pinctrl_kpp: kppgrp {
-			fsl,pins = <
-				MX53_PAD_GPIO_9__KPP_COL_6 0x1f4
-				MX53_PAD_GPIO_4__KPP_COL_7 0x1f4
-				MX53_PAD_KEY_COL2__KPP_COL_2 0x1f4
-				MX53_PAD_KEY_COL3__KPP_COL_3 0x1f4
-				MX53_PAD_GPIO_2__KPP_ROW_6 0x1f4
-				MX53_PAD_GPIO_5__KPP_ROW_7 0x1f4
-				MX53_PAD_KEY_ROW2__KPP_ROW_2 0x1f4
-				MX53_PAD_KEY_ROW3__KPP_ROW_3 0x1f4
-			>;
-		};
+	pinctrl_kpp: kppgrp {
+		fsl,pins = <
+			MX53_PAD_GPIO_9__KPP_COL_6 0x1f4
+			MX53_PAD_GPIO_4__KPP_COL_7 0x1f4
+			MX53_PAD_KEY_COL2__KPP_COL_2 0x1f4
+			MX53_PAD_KEY_COL3__KPP_COL_3 0x1f4
+			MX53_PAD_GPIO_2__KPP_ROW_6 0x1f4
+			MX53_PAD_GPIO_5__KPP_ROW_7 0x1f4
+			MX53_PAD_KEY_ROW2__KPP_ROW_2 0x1f4
+			MX53_PAD_KEY_ROW3__KPP_ROW_3 0x1f4
+		>;
+	};
 
-		pinctrl_rgb24_vga1: rgb24-vgagrp1 {
-			fsl,pins = <
-				MX53_PAD_DI0_DISP_CLK__IPU_DI0_DISP_CLK		0x5
-				MX53_PAD_DI0_PIN15__IPU_DI0_PIN15		0x5
-				MX53_PAD_DI0_PIN2__IPU_DI0_PIN2			0x5
-				MX53_PAD_DI0_PIN3__IPU_DI0_PIN3			0x5
-				MX53_PAD_DISP0_DAT0__IPU_DISP0_DAT_0		0x5
-				MX53_PAD_DISP0_DAT1__IPU_DISP0_DAT_1		0x5
-				MX53_PAD_DISP0_DAT2__IPU_DISP0_DAT_2		0x5
-				MX53_PAD_DISP0_DAT3__IPU_DISP0_DAT_3		0x5
-				MX53_PAD_DISP0_DAT4__IPU_DISP0_DAT_4		0x5
-				MX53_PAD_DISP0_DAT5__IPU_DISP0_DAT_5		0x5
-				MX53_PAD_DISP0_DAT6__IPU_DISP0_DAT_6		0x5
-				MX53_PAD_DISP0_DAT7__IPU_DISP0_DAT_7		0x5
-				MX53_PAD_DISP0_DAT8__IPU_DISP0_DAT_8		0x5
-				MX53_PAD_DISP0_DAT9__IPU_DISP0_DAT_9		0x5
-				MX53_PAD_DISP0_DAT10__IPU_DISP0_DAT_10		0x5
-				MX53_PAD_DISP0_DAT11__IPU_DISP0_DAT_11		0x5
-				MX53_PAD_DISP0_DAT12__IPU_DISP0_DAT_12		0x5
-				MX53_PAD_DISP0_DAT13__IPU_DISP0_DAT_13		0x5
-				MX53_PAD_DISP0_DAT14__IPU_DISP0_DAT_14		0x5
-				MX53_PAD_DISP0_DAT15__IPU_DISP0_DAT_15		0x5
-				MX53_PAD_DISP0_DAT16__IPU_DISP0_DAT_16		0x5
-				MX53_PAD_DISP0_DAT17__IPU_DISP0_DAT_17		0x5
-				MX53_PAD_DISP0_DAT18__IPU_DISP0_DAT_18		0x5
-				MX53_PAD_DISP0_DAT19__IPU_DISP0_DAT_19		0x5
-				MX53_PAD_DISP0_DAT20__IPU_DISP0_DAT_20		0x5
-				MX53_PAD_DISP0_DAT21__IPU_DISP0_DAT_21		0x5
-				MX53_PAD_DISP0_DAT22__IPU_DISP0_DAT_22		0x5
-				MX53_PAD_DISP0_DAT23__IPU_DISP0_DAT_23		0x5
-			>;
-		};
+	pinctrl_rgb24_vga1: rgb24-vga1grp {
+		fsl,pins = <
+			MX53_PAD_DI0_DISP_CLK__IPU_DI0_DISP_CLK		0x5
+			MX53_PAD_DI0_PIN15__IPU_DI0_PIN15		0x5
+			MX53_PAD_DI0_PIN2__IPU_DI0_PIN2			0x5
+			MX53_PAD_DI0_PIN3__IPU_DI0_PIN3			0x5
+			MX53_PAD_DISP0_DAT0__IPU_DISP0_DAT_0		0x5
+			MX53_PAD_DISP0_DAT1__IPU_DISP0_DAT_1		0x5
+			MX53_PAD_DISP0_DAT2__IPU_DISP0_DAT_2		0x5
+			MX53_PAD_DISP0_DAT3__IPU_DISP0_DAT_3		0x5
+			MX53_PAD_DISP0_DAT4__IPU_DISP0_DAT_4		0x5
+			MX53_PAD_DISP0_DAT5__IPU_DISP0_DAT_5		0x5
+			MX53_PAD_DISP0_DAT6__IPU_DISP0_DAT_6		0x5
+			MX53_PAD_DISP0_DAT7__IPU_DISP0_DAT_7		0x5
+			MX53_PAD_DISP0_DAT8__IPU_DISP0_DAT_8		0x5
+			MX53_PAD_DISP0_DAT9__IPU_DISP0_DAT_9		0x5
+			MX53_PAD_DISP0_DAT10__IPU_DISP0_DAT_10		0x5
+			MX53_PAD_DISP0_DAT11__IPU_DISP0_DAT_11		0x5
+			MX53_PAD_DISP0_DAT12__IPU_DISP0_DAT_12		0x5
+			MX53_PAD_DISP0_DAT13__IPU_DISP0_DAT_13		0x5
+			MX53_PAD_DISP0_DAT14__IPU_DISP0_DAT_14		0x5
+			MX53_PAD_DISP0_DAT15__IPU_DISP0_DAT_15		0x5
+			MX53_PAD_DISP0_DAT16__IPU_DISP0_DAT_16		0x5
+			MX53_PAD_DISP0_DAT17__IPU_DISP0_DAT_17		0x5
+			MX53_PAD_DISP0_DAT18__IPU_DISP0_DAT_18		0x5
+			MX53_PAD_DISP0_DAT19__IPU_DISP0_DAT_19		0x5
+			MX53_PAD_DISP0_DAT20__IPU_DISP0_DAT_20		0x5
+			MX53_PAD_DISP0_DAT21__IPU_DISP0_DAT_21		0x5
+			MX53_PAD_DISP0_DAT22__IPU_DISP0_DAT_22		0x5
+			MX53_PAD_DISP0_DAT23__IPU_DISP0_DAT_23		0x5
+		>;
+	};
 
-		pinctrl_tsc2007: tsc2007grp {
-			fsl,pins = <
-				MX53_PAD_EIM_D26__GPIO3_26 0x1f0 /* Interrupt */
-			>;
-		};
+	pinctrl_tsc2007: tsc2007grp {
+		fsl,pins = <
+			MX53_PAD_EIM_D26__GPIO3_26 0x1f0 /* Interrupt */
+		>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx53-tx53-x13x.dts b/arch/arm/boot/dts/nxp/imx/imx53-tx53-x13x.dts
index 6cdf2082c742..96c37f4296e5 100644
--- a/arch/arm/boot/dts/imx53-tx53-x13x.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-tx53-x13x.dts
@@ -1,48 +1,6 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
 /*
  * Copyright 2013-2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
  */
 
 /dts-v1/;
@@ -139,42 +97,40 @@
 };
 
 &iomuxc {
-	imx53-tx53-x13x {
-		pinctrl_lvds0: lvds0grp {
-			fsl,pins = <
-				MX53_PAD_LVDS0_TX3_P__LDB_LVDS0_TX3 0x80000000
-				MX53_PAD_LVDS0_CLK_P__LDB_LVDS0_CLK 0x80000000
-				MX53_PAD_LVDS0_TX2_P__LDB_LVDS0_TX2 0x80000000
-				MX53_PAD_LVDS0_TX1_P__LDB_LVDS0_TX1 0x80000000
-				MX53_PAD_LVDS0_TX0_P__LDB_LVDS0_TX0 0x80000000
-			>;
-		};
+	pinctrl_lvds0: lvds0grp {
+		fsl,pins = <
+			MX53_PAD_LVDS0_TX3_P__LDB_LVDS0_TX3 0x80000000
+			MX53_PAD_LVDS0_CLK_P__LDB_LVDS0_CLK 0x80000000
+			MX53_PAD_LVDS0_TX2_P__LDB_LVDS0_TX2 0x80000000
+			MX53_PAD_LVDS0_TX1_P__LDB_LVDS0_TX1 0x80000000
+			MX53_PAD_LVDS0_TX0_P__LDB_LVDS0_TX0 0x80000000
+		>;
+	};
 
-		pinctrl_lvds1: lvds1grp {
-			fsl,pins = <
-				MX53_PAD_LVDS1_TX3_P__LDB_LVDS1_TX3 0x80000000
-				MX53_PAD_LVDS1_TX2_P__LDB_LVDS1_TX2 0x80000000
-				MX53_PAD_LVDS1_CLK_P__LDB_LVDS1_CLK 0x80000000
-				MX53_PAD_LVDS1_TX1_P__LDB_LVDS1_TX1 0x80000000
-				MX53_PAD_LVDS1_TX0_P__LDB_LVDS1_TX0 0x80000000
-			>;
-		};
+	pinctrl_lvds1: lvds1grp {
+		fsl,pins = <
+			MX53_PAD_LVDS1_TX3_P__LDB_LVDS1_TX3 0x80000000
+			MX53_PAD_LVDS1_TX2_P__LDB_LVDS1_TX2 0x80000000
+			MX53_PAD_LVDS1_CLK_P__LDB_LVDS1_CLK 0x80000000
+			MX53_PAD_LVDS1_TX1_P__LDB_LVDS1_TX1 0x80000000
+			MX53_PAD_LVDS1_TX0_P__LDB_LVDS1_TX0 0x80000000
+		>;
+	};
 
-		pinctrl_pwm1: pwm1grp {
-			fsl,pins = <MX53_PAD_GPIO_9__PWM1_PWMO 0x04>;
-		};
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <MX53_PAD_GPIO_9__PWM1_PWMO 0x04>;
+	};
 
-		pinctrl_eeti1: eeti1grp {
-			fsl,pins = <
-				MX53_PAD_EIM_D22__GPIO3_22 0x1f0 /* Interrupt */
-			>;
-		};
+	pinctrl_eeti1: eeti1grp {
+		fsl,pins = <
+			MX53_PAD_EIM_D22__GPIO3_22 0x1f0 /* Interrupt */
+		>;
+	};
 
-		pinctrl_eeti2: eeti2grp {
-			fsl,pins = <
-				MX53_PAD_EIM_D23__GPIO3_23 0x1f0 /* Interrupt */
-			>;
-		};
+	pinctrl_eeti2: eeti2grp {
+		fsl,pins = <
+			MX53_PAD_EIM_D23__GPIO3_23 0x1f0 /* Interrupt */
+		>;
 	};
 };
 
@@ -191,7 +147,7 @@
 		display-timings {
 			native-mode = <&lvds0_timing0>;
 
-			lvds0_timing0: hsd100pxn1 {
+			lvds0_timing0: timing-hsd100pxn1 {
 				clock-frequency = <65000000>;
 				hactive = <1024>;
 				vactive = <768>;
@@ -207,7 +163,7 @@
 				pixelclk-active = <1>;
 			};
 
-			lvds0_timing1: nl12880bc20 {
+			lvds0_timing1: timing-nl12880bc20 {
 				clock-frequency = <71000000>;
 				hactive = <1280>;
 				vactive = <800>;
@@ -233,7 +189,7 @@
 		display-timings {
 			native-mode = <&lvds1_timing0>;
 
-			lvds1_timing0: hsd100pxn1 {
+			lvds1_timing0: timing-hsd100pxn1 {
 				clock-frequency = <65000000>;
 				hactive = <1024>;
 				vactive = <768>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx53-tx53.dtsi b/arch/arm/boot/dts/nxp/imx/imx53-tx53.dtsi
new file mode 100644
index 000000000000..88855d3b2031
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx53-tx53.dtsi
@@ -0,0 +1,546 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2012-2017 <LW@KARO-electronics.de>
+ * based on imx53-qsb.dts
+ *   Copyright 2011 Freescale Semiconductor, Inc.
+ *   Copyright 2011 Linaro Ltd.
+ */
+
+#include "imx53.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Ka-Ro electronics TX53 module";
+	compatible = "karo,tx53", "fsl,imx53";
+
+	/* Will be filled by the bootloader */
+	memory@70000000 {
+		device_type = "memory";
+		reg = <0x70000000 0>;
+	};
+
+	aliases {
+		can0 = &can2; /* Make the can interface indices consistent with TX28/TX48 modules */
+		can1 = &can1;
+		ipu = &ipu;
+		reg-can-xcvr = &reg_can_xcvr;
+		usbh1 = &usbh1;
+		usbotg = &usbotg;
+	};
+
+	clocks {
+		ckih1 {
+			clock-frequency = <0>;
+		};
+	};
+
+	mclk: clock-mclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_key>;
+
+		key-power {
+			label = "Power Button";
+			gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+			linux,code = <116>; /* KEY_POWER */
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_stk5led>;
+
+		led-user {
+			label = "Heartbeat";
+			gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	reg_2v5: regulator-2v5 {
+		compatible = "regulator-fixed";
+		regulator-name = "2V5";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_can_xcvr: regulator-can-xcvr {
+		compatible = "regulator-fixed";
+		regulator-name = "CAN XCVR";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can_xcvr>;
+		gpio = <&gpio4 21 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_usbh1_vbus: regulator-usbh1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usbh1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh1_vbus>;
+		gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usbotg_vbus: regulator-usbotg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usbotg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbotg_vbus>;
+		gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	sound {
+		compatible = "karo,tx53-audio-sgtl5000", "fsl,imx-audio-sgtl5000";
+		model = "tx53-audio-sgtl5000";
+		ssi-controller = <&ssi1>;
+		audio-codec = <&sgtl5000>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"Headphone Jack", "HP_OUT";
+		/* '1' based port numbers according to datasheet names */
+		mux-int-port = <1>;
+		mux-ext-port = <5>;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ssi1>;
+	status = "okay";
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	xceiver-supply = <&reg_can_xcvr>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can2>;
+	xceiver-supply = <&reg_can_xcvr>;
+	status = "okay";
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	cs-gpios = <
+		&gpio2 30 GPIO_ACTIVE_HIGH
+		&gpio3 19 GPIO_ACTIVE_HIGH
+	>;
+
+};
+
+&esdhc1 {
+	cd-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
+	fsl,wp-controller;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc1>;
+	status = "okay";
+};
+
+&esdhc2 {
+	cd-gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
+	fsl,wp-controller;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc2>;
+	status = "okay";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec>;
+	phy-mode = "rmii";
+	phy-reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
+	phy-handle = <&phy0>;
+	mac-address = [000000000000]; /* placeholder; will be overwritten by bootloader */
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+			interrupt-parent = <&gpio2>;
+			interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+			device_type = "ethernet-phy";
+		};
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-0 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio3 28 GPIO_ACTIVE_HIGH>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	rtc1: rtc@68 {
+		compatible = "dallas,ds1339";
+		reg = <0x68>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ds1339>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <20 IRQ_TYPE_EDGE_FALLING>;
+		trickle-resistor-ohms = <250>;
+		trickle-diode-disable;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_hog: hoggrp {
+		/* pins not in use by any device on the Starterkit board series */
+		fsl,pins = <
+			/* CMOS Sensor Interface */
+			MX53_PAD_CSI0_DAT12__GPIO5_30 0x1f4
+			MX53_PAD_CSI0_DAT13__GPIO5_31 0x1f4
+			MX53_PAD_CSI0_DAT14__GPIO6_0 0x1f4
+			MX53_PAD_CSI0_DAT15__GPIO6_1 0x1f4
+			MX53_PAD_CSI0_DAT16__GPIO6_2 0x1f4
+			MX53_PAD_CSI0_DAT17__GPIO6_3 0x1f4
+			MX53_PAD_CSI0_DAT18__GPIO6_4 0x1f4
+			MX53_PAD_CSI0_DAT19__GPIO6_5 0x1f4
+			MX53_PAD_CSI0_MCLK__GPIO5_19 0x1f4
+			MX53_PAD_CSI0_VSYNC__GPIO5_21 0x1f4
+			MX53_PAD_CSI0_PIXCLK__GPIO5_18 0x1f4
+			MX53_PAD_GPIO_0__GPIO1_0 0x1f4
+			/* Module Specific Signal */
+			/* MX53_PAD_NANDF_CS2__GPIO6_15 0x1f4 maybe used by EDT-FT5x06 */
+			/* MX53_PAD_EIM_A16__GPIO2_22 0x1f4 maybe used by EDT-FT5x06 */
+			MX53_PAD_EIM_D29__GPIO3_29 0x1f4
+			MX53_PAD_EIM_EB3__GPIO2_31 0x1f4
+			/* MX53_PAD_EIM_A17__GPIO2_21 0x1f4 maybe used by EDT-FT5x06 */
+			/* MX53_PAD_EIM_A18__GPIO2_20 0x1f4 used by LED */
+			MX53_PAD_EIM_A19__GPIO2_19 0x1f4
+			MX53_PAD_EIM_A20__GPIO2_18 0x1f4
+			MX53_PAD_EIM_A21__GPIO2_17 0x1f4
+			MX53_PAD_EIM_A22__GPIO2_16 0x1f4
+			MX53_PAD_EIM_A23__GPIO6_6 0x1f4
+			MX53_PAD_EIM_A24__GPIO5_4 0x1f4
+			MX53_PAD_CSI0_DAT8__GPIO5_26 0x1f4
+			MX53_PAD_CSI0_DAT9__GPIO5_27 0x1f4
+			MX53_PAD_CSI0_DAT10__GPIO5_28 0x1f4
+			MX53_PAD_CSI0_DAT11__GPIO5_29 0x1f4
+			/* MX53_PAD_EIM_D22__GPIO3_22 0x1f4 maybe used by EETI touchpanel driver */
+			/* MX53_PAD_EIM_D23__GPIO3_23 0x1f4 maybe used by EETI touchpanel driver */
+			MX53_PAD_GPIO_13__GPIO4_3 0x1f4
+			MX53_PAD_EIM_CS0__GPIO2_23 0x1f4
+			MX53_PAD_EIM_CS1__GPIO2_24 0x1f4
+			MX53_PAD_CSI0_DATA_EN__GPIO5_20 0x1f4
+			MX53_PAD_EIM_WAIT__GPIO5_0 0x1f4
+			MX53_PAD_EIM_EB0__GPIO2_28 0x1f4
+			MX53_PAD_EIM_EB1__GPIO2_29 0x1f4
+			MX53_PAD_EIM_OE__GPIO2_25 0x1f4
+			MX53_PAD_EIM_LBA__GPIO2_27 0x1f4
+			MX53_PAD_EIM_RW__GPIO2_26 0x1f4
+			MX53_PAD_EIM_DA8__GPIO3_8 0x1f4
+			MX53_PAD_EIM_DA9__GPIO3_9 0x1f4
+			MX53_PAD_EIM_DA10__GPIO3_10 0x1f4
+			MX53_PAD_EIM_DA11__GPIO3_11 0x1f4
+			MX53_PAD_EIM_DA12__GPIO3_12 0x1f4
+			MX53_PAD_EIM_DA13__GPIO3_13 0x1f4
+			MX53_PAD_EIM_DA14__GPIO3_14 0x1f4
+			MX53_PAD_EIM_DA15__GPIO3_15 0x1f4
+			>;
+	};
+
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX53_PAD_GPIO_7__CAN1_TXCAN		0x80000000
+			MX53_PAD_GPIO_8__CAN1_RXCAN		0x80000000
+		>;
+	};
+
+	pinctrl_can2: can2grp {
+		fsl,pins = <
+			MX53_PAD_KEY_COL4__CAN2_TXCAN		0x80000000
+			MX53_PAD_KEY_ROW4__CAN2_RXCAN		0x80000000
+		>;
+	};
+
+	pinctrl_can_xcvr: can-xcvrgrp {
+		fsl,pins = <MX53_PAD_DISP0_DAT0__GPIO4_21 0xe0>; /* Flexcan XCVR enable */
+	};
+
+	pinctrl_ds1339: ds1339grp {
+		fsl,pins = <MX53_PAD_DI0_PIN4__GPIO4_20 0xe0>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX53_PAD_GPIO_19__ECSPI1_RDY		0x80000000
+			MX53_PAD_EIM_EB2__ECSPI1_SS0		0x80000000
+			MX53_PAD_EIM_D16__ECSPI1_SCLK		0x80000000
+			MX53_PAD_EIM_D17__ECSPI1_MISO		0x80000000
+			MX53_PAD_EIM_D18__ECSPI1_MOSI		0x80000000
+			MX53_PAD_EIM_D19__ECSPI1_SS1		0x80000000
+		>;
+	};
+
+	pinctrl_esdhc1: esdhc1grp {
+		fsl,pins = <
+			MX53_PAD_SD1_DATA0__ESDHC1_DAT0		0x1d5
+			MX53_PAD_SD1_DATA1__ESDHC1_DAT1		0x1d5
+			MX53_PAD_SD1_DATA2__ESDHC1_DAT2		0x1d5
+			MX53_PAD_SD1_DATA3__ESDHC1_DAT3		0x1d5
+			MX53_PAD_SD1_CMD__ESDHC1_CMD		0x1d5
+			MX53_PAD_SD1_CLK__ESDHC1_CLK		0x1d5
+			MX53_PAD_EIM_D24__GPIO3_24 0x1f0
+		>;
+	};
+
+	pinctrl_esdhc2: esdhc2grp {
+		fsl,pins = <
+			MX53_PAD_SD2_CMD__ESDHC2_CMD		0x1d5
+			MX53_PAD_SD2_CLK__ESDHC2_CLK		0x1d5
+			MX53_PAD_SD2_DATA0__ESDHC2_DAT0		0x1d5
+			MX53_PAD_SD2_DATA1__ESDHC2_DAT1		0x1d5
+			MX53_PAD_SD2_DATA2__ESDHC2_DAT2		0x1d5
+			MX53_PAD_SD2_DATA3__ESDHC2_DAT3		0x1d5
+			MX53_PAD_EIM_D25__GPIO3_25 0x1f0
+		>;
+	};
+
+	pinctrl_fec: fecgrp {
+		fsl,pins = <
+			MX53_PAD_FEC_MDC__FEC_MDC		0x80000000
+			MX53_PAD_FEC_MDIO__FEC_MDIO		0x80000000
+			MX53_PAD_FEC_REF_CLK__FEC_TX_CLK	0x80000000
+			MX53_PAD_FEC_RX_ER__FEC_RX_ER		0x80000000
+			MX53_PAD_FEC_CRS_DV__FEC_RX_DV		0x80000000
+			MX53_PAD_FEC_RXD1__FEC_RDATA_1		0x80000000
+			MX53_PAD_FEC_RXD0__FEC_RDATA_0		0x80000000
+			MX53_PAD_FEC_TX_EN__FEC_TX_EN		0x80000000
+			MX53_PAD_FEC_TXD1__FEC_TDATA_1		0x80000000
+			MX53_PAD_FEC_TXD0__FEC_TDATA_0		0x80000000
+		>;
+	};
+
+	pinctrl_gpio_key: gpio-keygrp {
+		fsl,pins = <MX53_PAD_EIM_A25__GPIO5_2 0x1f4>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX53_PAD_EIM_D21__I2C1_SCL		0x400001e4
+			MX53_PAD_EIM_D28__I2C1_SDA		0x400001e4
+		>;
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpiogrp {
+		fsl,pins = <
+			MX53_PAD_EIM_D21__GPIO3_21		0x400001e6
+			MX53_PAD_EIM_D28__GPIO3_28		0x400001e6
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX53_PAD_GPIO_3__I2C3_SCL		0x400001e4
+			MX53_PAD_GPIO_6__I2C3_SDA		0x400001e4
+		>;
+	};
+
+	pinctrl_i2c3_gpio: i2c3-gpiogrp {
+		fsl,pins = <
+			MX53_PAD_GPIO_3__GPIO1_3		0x400001e6
+			MX53_PAD_GPIO_6__GPIO1_6		0x400001e6
+		>;
+	};
+
+	pinctrl_nand: nandgrp {
+		fsl,pins = <
+			MX53_PAD_NANDF_WE_B__EMI_NANDF_WE_B	0x4
+			MX53_PAD_NANDF_RE_B__EMI_NANDF_RE_B	0x4
+			MX53_PAD_NANDF_CLE__EMI_NANDF_CLE	0x4
+			MX53_PAD_NANDF_ALE__EMI_NANDF_ALE	0x4
+			MX53_PAD_NANDF_WP_B__EMI_NANDF_WP_B	0xe0
+			MX53_PAD_NANDF_RB0__EMI_NANDF_RB_0	0xe0
+			MX53_PAD_NANDF_CS0__EMI_NANDF_CS_0	0x4
+			MX53_PAD_EIM_DA0__EMI_NAND_WEIM_DA_0	0xa4
+			MX53_PAD_EIM_DA1__EMI_NAND_WEIM_DA_1	0xa4
+			MX53_PAD_EIM_DA2__EMI_NAND_WEIM_DA_2	0xa4
+			MX53_PAD_EIM_DA3__EMI_NAND_WEIM_DA_3	0xa4
+			MX53_PAD_EIM_DA4__EMI_NAND_WEIM_DA_4	0xa4
+			MX53_PAD_EIM_DA5__EMI_NAND_WEIM_DA_5	0xa4
+			MX53_PAD_EIM_DA6__EMI_NAND_WEIM_DA_6	0xa4
+			MX53_PAD_EIM_DA7__EMI_NAND_WEIM_DA_7	0xa4
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX53_PAD_GPIO_1__PWM2_PWMO		0x80000000
+		>;
+	};
+
+	pinctrl_ssi1: ssi1grp {
+		fsl,pins = <
+			MX53_PAD_KEY_COL0__AUDMUX_AUD5_TXC	0x80000000
+			MX53_PAD_KEY_ROW0__AUDMUX_AUD5_TXD	0x80000000
+			MX53_PAD_KEY_COL1__AUDMUX_AUD5_TXFS	0x80000000
+			MX53_PAD_KEY_ROW1__AUDMUX_AUD5_RXD	0x80000000
+		>;
+	};
+
+	pinctrl_ssi2: ssi2grp {
+		fsl,pins = <
+			MX53_PAD_CSI0_DAT4__AUDMUX_AUD3_TXC	0x80000000
+			MX53_PAD_CSI0_DAT5__AUDMUX_AUD3_TXD	0x80000000
+			MX53_PAD_CSI0_DAT6__AUDMUX_AUD3_TXFS	0x80000000
+			MX53_PAD_CSI0_DAT7__AUDMUX_AUD3_RXD	0x80000000
+			MX53_PAD_EIM_D27__GPIO3_27 0x1f0
+		>;
+	};
+
+	pinctrl_stk5led: stk5ledgrp {
+		fsl,pins = <MX53_PAD_EIM_A18__GPIO2_20 0xc0>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX53_PAD_PATA_DIOW__UART1_TXD_MUX	0x1e4
+			MX53_PAD_PATA_DMACK__UART1_RXD_MUX	0x1e4
+			MX53_PAD_PATA_RESET_B__UART1_CTS	0x1c5
+			MX53_PAD_PATA_IORDY__UART1_RTS		0x1c5
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX	0x1c5
+			MX53_PAD_PATA_DMARQ__UART2_TXD_MUX	0x1c5
+			MX53_PAD_PATA_DIOR__UART2_RTS		0x1c5
+			MX53_PAD_PATA_INTRQ__UART2_CTS		0x1c5
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX53_PAD_PATA_CS_0__UART3_TXD_MUX	0x1e4
+			MX53_PAD_PATA_CS_1__UART3_RXD_MUX	0x1e4
+			MX53_PAD_PATA_DA_1__UART3_CTS		0x1e4
+			MX53_PAD_PATA_DA_2__UART3_RTS		0x1e4
+		>;
+	};
+
+	pinctrl_usbh1: usbh1grp {
+		fsl,pins = <
+			MX53_PAD_EIM_D30__GPIO3_30 0x100 /* OC */
+		>;
+	};
+
+	pinctrl_usbh1_vbus: usbh1-vbusgrp {
+		fsl,pins = <
+			MX53_PAD_EIM_D31__GPIO3_31 0xe0 /* VBUS ENABLE */
+		>;
+	};
+
+	pinctrl_usbotg_vbus: usbotg-vbusgrp {
+		fsl,pins = <
+			MX53_PAD_GPIO_7__GPIO1_7 0xe0 /* VBUS ENABLE */
+			MX53_PAD_GPIO_8__GPIO1_8 0x100 /* OC */
+		>;
+	};
+};
+
+&ipu {
+	status = "okay";
+};
+
+&nfc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_nand>;
+	nand-bus-width = <8>;
+	nand-ecc-mode = "hw";
+	nand-on-flash-bbt;
+	status = "okay";
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+};
+
+&sdma {
+	fsl,sdma-ram-script-name = "sdma-imx53.bin";
+};
+
+&ssi1 {
+	status = "okay";
+};
+
+&ssi2 {
+	status = "disabled";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbh1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbh1>;
+	phy_type = "utmi";
+	disable-over-current;
+	vbus-supply = <&reg_usbh1_vbus>;
+	status = "okay";
+};
+
+&usbotg {
+	phy_type = "utmi";
+	dr_mode = "peripheral";
+	disable-over-current;
+	vbus-supply = <&reg_usbotg_vbus>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx53-usbarmory.dts b/arch/arm/boot/dts/nxp/imx/imx53-usbarmory.dts
index f34993a490ee..acc44010d510 100644
--- a/arch/arm/boot/dts/imx53-usbarmory.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-usbarmory.dts
@@ -67,7 +67,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_led>;
 
-		user {
+		led-user {
 			label = "LED";
 			gpios = <&gpio4 27 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/imx53-voipac-bsb.dts b/arch/arm/boot/dts/nxp/imx/imx53-voipac-bsb.dts
index ae53d178a683..ae9cc04f23eb 100644
--- a/arch/arm/boot/dts/imx53-voipac-bsb.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx53-voipac-bsb.dts
@@ -40,67 +40,65 @@
 
 &iomuxc {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_hog>;
-
-	imx53-voipac {
-		pinctrl_hog: hoggrp {
-			fsl,pins = <
-				/* SD2_CD */
-				MX53_PAD_EIM_D25__GPIO3_25	0x80000000
-				/* SD2_WP */
-				MX53_PAD_EIM_A19__GPIO2_19 	0x80000000
-			>;
-		};
+	pinctrl-0 = <&pinctrl_hogbsb>;
+
+	pinctrl_hogbsb: hogbsbgrp {
+		fsl,pins = <
+			/* SD2_CD */
+			MX53_PAD_EIM_D25__GPIO3_25	0x80000000
+			/* SD2_WP */
+			MX53_PAD_EIM_A19__GPIO2_19 	0x80000000
+		>;
+	};
 
-		led_pin_gpio: led_gpio {
-			fsl,pins = <
-				MX53_PAD_EIM_D29__GPIO3_29	0x80000000
-				MX53_PAD_EIM_EB3__GPIO2_31	0x80000000
-			>;
-		};
+	led_pin_gpio: ledgpiogrp {
+		fsl,pins = <
+			MX53_PAD_EIM_D29__GPIO3_29	0x80000000
+			MX53_PAD_EIM_EB3__GPIO2_31	0x80000000
+		>;
+	};
 
-		/* Keyboard controller */
-		pinctrl_kpp_1: kppgrp-1 {
-			fsl,pins = <
-				MX53_PAD_GPIO_9__KPP_COL_6	0xe8
-				MX53_PAD_GPIO_4__KPP_COL_7	0xe8
-				MX53_PAD_KEY_COL2__KPP_COL_2	0xe8
-				MX53_PAD_KEY_COL3__KPP_COL_3	0xe8
-				MX53_PAD_KEY_COL4__KPP_COL_4	0xe8
-				MX53_PAD_GPIO_2__KPP_ROW_6	0xe0
-				MX53_PAD_GPIO_5__KPP_ROW_7	0xe0
-				MX53_PAD_KEY_ROW2__KPP_ROW_2	0xe0
-				MX53_PAD_KEY_ROW3__KPP_ROW_3	0xe0
-				MX53_PAD_KEY_ROW4__KPP_ROW_4	0xe0
-			>;
-		};
+	/* Keyboard controller */
+	pinctrl_kpp_1: kpp1grp {
+		fsl,pins = <
+			MX53_PAD_GPIO_9__KPP_COL_6	0xe8
+			MX53_PAD_GPIO_4__KPP_COL_7	0xe8
+			MX53_PAD_KEY_COL2__KPP_COL_2	0xe8
+			MX53_PAD_KEY_COL3__KPP_COL_3	0xe8
+			MX53_PAD_KEY_COL4__KPP_COL_4	0xe8
+			MX53_PAD_GPIO_2__KPP_ROW_6	0xe0
+			MX53_PAD_GPIO_5__KPP_ROW_7	0xe0
+			MX53_PAD_KEY_ROW2__KPP_ROW_2	0xe0
+			MX53_PAD_KEY_ROW3__KPP_ROW_3	0xe0
+			MX53_PAD_KEY_ROW4__KPP_ROW_4	0xe0
+		>;
+	};
 
-		pinctrl_audmux: audmuxgrp {
-			fsl,pins = <
-				MX53_PAD_KEY_COL0__AUDMUX_AUD5_TXC	0x80000000
-				MX53_PAD_KEY_ROW0__AUDMUX_AUD5_TXD	0x80000000
-				MX53_PAD_KEY_COL1__AUDMUX_AUD5_TXFS	0x80000000
-				MX53_PAD_KEY_ROW1__AUDMUX_AUD5_RXD	0x80000000
-			>;
-		};
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX53_PAD_KEY_COL0__AUDMUX_AUD5_TXC	0x80000000
+			MX53_PAD_KEY_ROW0__AUDMUX_AUD5_TXD	0x80000000
+			MX53_PAD_KEY_COL1__AUDMUX_AUD5_TXFS	0x80000000
+			MX53_PAD_KEY_ROW1__AUDMUX_AUD5_RXD	0x80000000
+		>;
+	};
 
-		pinctrl_esdhc2: esdhc2grp {
-			fsl,pins = <
-				MX53_PAD_SD2_CMD__ESDHC2_CMD		0x1d5
-				MX53_PAD_SD2_CLK__ESDHC2_CLK		0x1d5
-				MX53_PAD_SD2_DATA0__ESDHC2_DAT0		0x1d5
-				MX53_PAD_SD2_DATA1__ESDHC2_DAT1		0x1d5
-				MX53_PAD_SD2_DATA2__ESDHC2_DAT2		0x1d5
-				MX53_PAD_SD2_DATA3__ESDHC2_DAT3		0x1d5
-			>;
-		};
+	pinctrl_esdhc2: esdhc2grp {
+		fsl,pins = <
+			MX53_PAD_SD2_CMD__ESDHC2_CMD		0x1d5
+			MX53_PAD_SD2_CLK__ESDHC2_CLK		0x1d5
+			MX53_PAD_SD2_DATA0__ESDHC2_DAT0		0x1d5
+			MX53_PAD_SD2_DATA1__ESDHC2_DAT1		0x1d5
+			MX53_PAD_SD2_DATA2__ESDHC2_DAT2		0x1d5
+			MX53_PAD_SD2_DATA3__ESDHC2_DAT3		0x1d5
+		>;
+	};
 
-		pinctrl_i2c3: i2c3grp {
-			fsl,pins = <
-				MX53_PAD_GPIO_3__I2C3_SCL		0xc0000000
-				MX53_PAD_GPIO_6__I2C3_SDA		0xc0000000
-			>;
-		};
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX53_PAD_GPIO_3__I2C3_SCL		0xc0000000
+			MX53_PAD_GPIO_6__I2C3_SDA		0xc0000000
+		>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx53-voipac-dmm-668.dtsi b/arch/arm/boot/dts/nxp/imx/imx53-voipac-dmm-668.dtsi
index 24859d0c09c1..6dc70a92d831 100644
--- a/arch/arm/boot/dts/imx53-voipac-dmm-668.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx53-voipac-dmm-668.dtsi
@@ -15,29 +15,21 @@
 		      <0xb0000000 0x20000000>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 
-		reg_usb_vbus: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "usb_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 31 0>; /* PEN */
-			enable-active-high;
-		};
+	reg_usb_vbus: regulator-usb-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 31 0>; /* PEN */
+		enable-active-high;
 	};
 };
 
@@ -45,74 +37,72 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hog>;
 
-	imx53-voipac {
-		pinctrl_hog: hoggrp {
-			fsl,pins = <
-				/* Make DA9053 regulator functional */
-				MX53_PAD_GPIO_16__GPIO7_11	0x80000000
-				/* FEC Power enable */
-				MX53_PAD_GPIO_11__GPIO4_1	0x80000000
-				/* FEC RST */
-				MX53_PAD_GPIO_12__GPIO4_2	0x80000000
-			>;
-		};
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			/* Make DA9053 regulator functional */
+			MX53_PAD_GPIO_16__GPIO7_11	0x80000000
+			/* FEC Power enable */
+			MX53_PAD_GPIO_11__GPIO4_1	0x80000000
+			/* FEC RST */
+			MX53_PAD_GPIO_12__GPIO4_2	0x80000000
+		>;
+	};
 
-		pinctrl_ecspi1: ecspi1grp {
-			fsl,pins = <
-				MX53_PAD_EIM_D16__ECSPI1_SCLK		0x80000000
-				MX53_PAD_EIM_D17__ECSPI1_MISO		0x80000000
-				MX53_PAD_EIM_D18__ECSPI1_MOSI		0x80000000
-			>;
-		};
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX53_PAD_EIM_D16__ECSPI1_SCLK		0x80000000
+			MX53_PAD_EIM_D17__ECSPI1_MISO		0x80000000
+			MX53_PAD_EIM_D18__ECSPI1_MOSI		0x80000000
+		>;
+	};
 
-		pinctrl_fec: fecgrp {
-			fsl,pins = <
-				MX53_PAD_FEC_MDC__FEC_MDC		0x80000000
-				MX53_PAD_FEC_MDIO__FEC_MDIO		0x80000000
-				MX53_PAD_FEC_REF_CLK__FEC_TX_CLK	0x80000000
-				MX53_PAD_FEC_RX_ER__FEC_RX_ER		0x80000000
-				MX53_PAD_FEC_CRS_DV__FEC_RX_DV		0x80000000
-				MX53_PAD_FEC_RXD1__FEC_RDATA_1		0x80000000
-				MX53_PAD_FEC_RXD0__FEC_RDATA_0		0x80000000
-				MX53_PAD_FEC_TX_EN__FEC_TX_EN		0x80000000
-				MX53_PAD_FEC_TXD1__FEC_TDATA_1		0x80000000
-				MX53_PAD_FEC_TXD0__FEC_TDATA_0		0x80000000
-			>;
-		};
+	pinctrl_fec: fecgrp {
+		fsl,pins = <
+			MX53_PAD_FEC_MDC__FEC_MDC		0x80000000
+			MX53_PAD_FEC_MDIO__FEC_MDIO		0x80000000
+			MX53_PAD_FEC_REF_CLK__FEC_TX_CLK	0x80000000
+			MX53_PAD_FEC_RX_ER__FEC_RX_ER		0x80000000
+			MX53_PAD_FEC_CRS_DV__FEC_RX_DV		0x80000000
+			MX53_PAD_FEC_RXD1__FEC_RDATA_1		0x80000000
+			MX53_PAD_FEC_RXD0__FEC_RDATA_0		0x80000000
+			MX53_PAD_FEC_TX_EN__FEC_TX_EN		0x80000000
+			MX53_PAD_FEC_TXD1__FEC_TDATA_1		0x80000000
+			MX53_PAD_FEC_TXD0__FEC_TDATA_0		0x80000000
+		>;
+	};
 
-		pinctrl_i2c1: i2c1grp {
-			fsl,pins = <
-				MX53_PAD_EIM_D21__I2C1_SCL		0xc0000000
-				MX53_PAD_EIM_D28__I2C1_SDA		0xc0000000
-			>;
-		};
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX53_PAD_EIM_D21__I2C1_SCL		0xc0000000
+			MX53_PAD_EIM_D28__I2C1_SDA		0xc0000000
+		>;
+	};
 
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX53_PAD_PATA_DIOW__UART1_TXD_MUX	0x1e4
-				MX53_PAD_PATA_DMACK__UART1_RXD_MUX	0x1e4
-			>;
-		};
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX53_PAD_PATA_DIOW__UART1_TXD_MUX	0x1e4
+			MX53_PAD_PATA_DMACK__UART1_RXD_MUX	0x1e4
+		>;
+	};
 
-		pinctrl_nand: nandgrp {
-			fsl,pins = <
-				MX53_PAD_NANDF_WE_B__EMI_NANDF_WE_B	0x4
-				MX53_PAD_NANDF_RE_B__EMI_NANDF_RE_B	0x4
-				MX53_PAD_NANDF_CLE__EMI_NANDF_CLE	0x4
-				MX53_PAD_NANDF_ALE__EMI_NANDF_ALE	0x4
-				MX53_PAD_NANDF_WP_B__EMI_NANDF_WP_B	0xe0
-				MX53_PAD_NANDF_RB0__EMI_NANDF_RB_0	0xe0
-				MX53_PAD_NANDF_CS0__EMI_NANDF_CS_0	0x4
-				MX53_PAD_PATA_DATA0__EMI_NANDF_D_0	0xa4
-				MX53_PAD_PATA_DATA1__EMI_NANDF_D_1	0xa4
-				MX53_PAD_PATA_DATA2__EMI_NANDF_D_2	0xa4
-				MX53_PAD_PATA_DATA3__EMI_NANDF_D_3	0xa4
-				MX53_PAD_PATA_DATA4__EMI_NANDF_D_4	0xa4
-				MX53_PAD_PATA_DATA5__EMI_NANDF_D_5	0xa4
-				MX53_PAD_PATA_DATA6__EMI_NANDF_D_6	0xa4
-				MX53_PAD_PATA_DATA7__EMI_NANDF_D_7	0xa4
-			>;
-		};
+	pinctrl_nand: nandgrp {
+		fsl,pins = <
+			MX53_PAD_NANDF_WE_B__EMI_NANDF_WE_B	0x4
+			MX53_PAD_NANDF_RE_B__EMI_NANDF_RE_B	0x4
+			MX53_PAD_NANDF_CLE__EMI_NANDF_CLE	0x4
+			MX53_PAD_NANDF_ALE__EMI_NANDF_ALE	0x4
+			MX53_PAD_NANDF_WP_B__EMI_NANDF_WP_B	0xe0
+			MX53_PAD_NANDF_RB0__EMI_NANDF_RB_0	0xe0
+			MX53_PAD_NANDF_CS0__EMI_NANDF_CS_0	0x4
+			MX53_PAD_PATA_DATA0__EMI_NANDF_D_0	0xa4
+			MX53_PAD_PATA_DATA1__EMI_NANDF_D_1	0xa4
+			MX53_PAD_PATA_DATA2__EMI_NANDF_D_2	0xa4
+			MX53_PAD_PATA_DATA3__EMI_NANDF_D_3	0xa4
+			MX53_PAD_PATA_DATA4__EMI_NANDF_D_4	0xa4
+			MX53_PAD_PATA_DATA5__EMI_NANDF_D_5	0xa4
+			MX53_PAD_PATA_DATA6__EMI_NANDF_D_6	0xa4
+			MX53_PAD_PATA_DATA7__EMI_NANDF_D_7	0xa4
+		>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx53.dtsi b/arch/arm/boot/dts/nxp/imx/imx53.dtsi
index 67487f3caee1..93225a56896f 100644
--- a/arch/arm/boot/dts/imx53.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx53.dtsi
@@ -132,7 +132,7 @@
 		status = "okay";
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
@@ -222,7 +222,7 @@
 			clock-names = "core_clk", "mem_iface_clk";
 		};
 
-		bus@50000000 { /* AIPS1 */
+		aips1: bus@50000000 { /* AIPS1 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -275,7 +275,7 @@
 				ecspi1: spi@50010000 {
 					#address-cells = <1>;
 					#size-cells = <0>;
-					compatible = "fsl,imx53-ecspi", "fsl,imx51-ecspi";
+					compatible = "fsl,imx53-ecspi";
 					reg = <0x50010000 0x4000>;
 					interrupts = <36>;
 					clocks = <&clks IMX5_CLK_ECSPI1_IPG_GATE>,
@@ -458,7 +458,7 @@
 				clocks = <&clks IMX5_CLK_SRTC_GATE>;
 			};
 
-			iomuxc: iomuxc@53fa8000 {
+			iomuxc: pinctrl@53fa8000 {
 				compatible = "fsl,imx53-iomuxc";
 				reg = <0x53fa8000 0x4000>;
 			};
@@ -595,10 +595,10 @@
 				#reset-cells = <1>;
 			};
 
-			clks: ccm@53fd4000{
+			clks: ccm@53fd4000 {
 				compatible = "fsl,imx53-ccm";
 				reg = <0x53fd4000 0x4000>;
-				interrupts = <0 71 0x04 0 72 0x04>;
+				interrupts = <71>, <72>;
 				#clock-cells = <1>;
 			};
 
@@ -655,7 +655,7 @@
 			};
 		};
 
-		bus@60000000 {	/* AIPS2 */
+		aips2: bus@60000000 {	/* AIPS2 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -668,7 +668,7 @@
 			};
 
 			iim: efuse@63f98000 {
-				compatible = "fsl,imx53-iim", "fsl,imx27-iim", "syscon";
+				compatible = "fsl,imx53-iim";
 				reg = <0x63f98000 0x4000>;
 				interrupts = <69>;
 				clocks = <&clks IMX5_CLK_IIM_GATE>;
@@ -701,7 +701,7 @@
 			ecspi2: spi@63fac000 {
 				#address-cells = <1>;
 				#size-cells = <0>;
-				compatible = "fsl,imx53-ecspi", "fsl,imx51-ecspi";
+				compatible = "fsl,imx53-ecspi";
 				reg = <0x63fac000 0x4000>;
 				interrupts = <37>;
 				clocks = <&clks IMX5_CLK_ECSPI2_IPG_GATE>,
@@ -710,7 +710,7 @@
 				status = "disabled";
 			};
 
-			sdma: sdma@63fb0000 {
+			sdma: dma-controller@63fb0000 {
 				compatible = "fsl,imx53-sdma", "fsl,imx35-sdma";
 				reg = <0x63fb0000 0x4000>;
 				interrupts = <6>;
@@ -775,7 +775,7 @@
 				status = "disabled";
 			};
 
-			nfc: nand@63fdb000 {
+			nfc: nand-controller@63fdb000 {
 				compatible = "fsl,imx53-nand";
 				reg = <0x63fdb000 0x1000 0xf7ff0000 0x10000>;
 				interrupts = <8>;
@@ -850,6 +850,9 @@
 		ocram: sram@f8000000 {
 			compatible = "mmio-sram";
 			reg = <0xf8000000 0x20000>;
+			ranges = <0 0xf8000000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX5_CLK_OCRAM>;
 		};
 	};
diff --git a/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi b/arch/arm/boot/dts/nxp/imx/imx6-logicpd-baseboard.dtsi
index d9de9b4f0c52..1e0a588b2a15 100644
--- a/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6-logicpd-baseboard.dtsi
@@ -6,7 +6,7 @@
 	keyboard {
 		compatible = "gpio-keys";
 
-		btn0 {
+		button-0 {
 			gpios = <&pcf8575 0 GPIO_ACTIVE_LOW>;
 			label = "btn0";
 			linux,code = <KEY_WAKEUP>;
@@ -14,7 +14,7 @@
 			wakeup-source;
 		};
 
-		btn1 {
+		button-1 {
 			gpios = <&pcf8575 1 GPIO_ACTIVE_LOW>;
 			label = "btn1";
 			linux,code = <KEY_WAKEUP>;
@@ -22,7 +22,7 @@
 			wakeup-source;
 		};
 
-		btn2 {
+		button-2 {
 			gpios = <&pcf8575 2 GPIO_ACTIVE_LOW>;
 			label = "btn2";
 			linux,code = <KEY_WAKEUP>;
@@ -30,7 +30,7 @@
 			wakeup-source;
 		};
 
-		btn3 {
+		button-3 {
 			gpios = <&pcf8575 3 GPIO_ACTIVE_LOW>;
 			label = "btn3";
 			linux,code = <KEY_WAKEUP>;
@@ -534,7 +534,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_100mhz: h100-usdhc2-100mhz {
+	pinctrl_usdhc2_100mhz: h100-usdhc2-100mhzgrp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1b0b0	/* CD */
 			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x170b9
@@ -546,7 +546,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_200mhz: h100-usdhc2-200mhz {
+	pinctrl_usdhc2_200mhz: h100-usdhc2-200mhzgrp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1b0b0	/* CD */
 			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x170f9
diff --git a/arch/arm/boot/dts/imx6-logicpd-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx6-logicpd-som.dtsi
index 547fb141ec0c..547fb141ec0c 100644
--- a/arch/arm/boot/dts/imx6-logicpd-som.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6-logicpd-som.dtsi
diff --git a/arch/arm/boot/dts/imx6dl-alti6p.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-alti6p.dts
index e8325fd680d9..9bb36db131c2 100644
--- a/arch/arm/boot/dts/imx6dl-alti6p.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-alti6p.dts
@@ -22,9 +22,10 @@
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <50000000>;
+		clock-output-names = "enet_ref_pad";
 	};
 
-	i2c2-mux {
+	i2c-mux-2 {
 		compatible = "i2c-mux";
 		i2c-parent = <&i2c2>;
 		mux-controls = <&i2c_mux>;
@@ -44,7 +45,7 @@
 		};
 	};
 
-	i2c4-mux {
+	i2c-mux-4 {
 		compatible = "i2c-mux";
 		i2c-parent = <&i2c4>;
 		mux-controls = <&i2c_mux>;
@@ -191,6 +192,13 @@
 	status = "okay";
 };
 
+&clks {
+	clocks = <&clock_ksz8081>;
+	clock-names = "enet_ref_pad";
+	assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&clock_ksz8081>;
+};
+
 &ecspi1 {
 	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
@@ -208,10 +216,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rmii";
-	clocks = <&clks IMX6QDL_CLK_ENET>,
-		 <&clks IMX6QDL_CLK_ENET>,
-		 <&clock_ksz8081>;
-	clock-names = "ipg", "ahb", "ptp";
 	status = "okay";
 
 	mdio {
@@ -357,6 +361,7 @@
 	pinctrl-0 = <&pinctrl_usbh1>;
 	phy_type = "utmi";
 	dr_mode = "host";
+	over-current-active-low;
 	status = "okay";
 };
 
@@ -366,9 +371,18 @@
 	pinctrl-0 = <&pinctrl_usbotg>;
 	phy_type = "utmi";
 	dr_mode = "host";
+	over-current-active-low;
 	status = "okay";
 };
 
+&usbphynop1 {
+	status = "disabled";
+};
+
+&usbphynop2 {
+	status = "disabled";
+};
+
 &usdhc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc1>;
diff --git a/arch/arm/boot/dts/imx6dl-apf6dev.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-apf6dev.dts
index 3dcce3454b08..3dcce3454b08 100644
--- a/arch/arm/boot/dts/imx6dl-apf6dev.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-apf6dev.dts
diff --git a/arch/arm/boot/dts/imx6dl-aristainetos2_4.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos2_4.dts
index dfa6f64d43cc..fc62ba2a4fcb 100644
--- a/arch/arm/boot/dts/imx6dl-aristainetos2_4.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos2_4.dts
@@ -1,44 +1,8 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
 /*
  * support for the imx6 based aristainetos2 board
  *
  * Copyright (C) 2015 Heiko Schocher <hs@denx.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 /dts-v1/;
 #include "imx6dl.dtsi"
@@ -82,11 +46,10 @@
 		compatible = "lg,lg4573";
 		spi-max-frequency = <10000000>;
 		reg = <0>;
-		power-on-delay = <10>;
 
 		display-timings {
-			480x800p57 {
-				native-mode;
+			native-mode = <&timing0>;
+			timing0: timing-480x800p57 {
 				clock-frequency = <27000027>;
 				hactive = <480>;
 				vactive = <800>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos2_7.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos2_7.dts
new file mode 100644
index 000000000000..a7400d42475b
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos2_7.dts
@@ -0,0 +1,62 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * support for the imx6 based aristainetos2 board
+ *
+ * Copyright (C) 2015 Heiko Schocher <hs@denx.de>
+ */
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-aristainetos2.dtsi"
+
+/ {
+	model = "aristainetos2 i.MX6 Dual Lite Board 7";
+	compatible = "abb,aristainetos2-imx6dl-7", "fsl,imx6dl";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x40000000>;
+	};
+
+	panel: panel {
+		compatible = "lg,lb070wv8";
+		backlight = <&backlight>;
+		enable-gpios = <&gpio6 15 GPIO_ACTIVE_HIGH>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+};
+
+&i2c3 {
+	touch: touch@4d {
+		compatible = "atmel,maxtouch";
+		reg = <0x4d>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <9 8>;
+	};
+};
+
+&ldb {
+	status = "okay";
+
+	lvds-channel@0 {
+		status = "okay";
+
+		port@0 {
+			reg = <0>;
+			lvds0_in: endpoint {
+				remote-endpoint = <&ipu1_di0_lvds0>;
+			};
+		};
+
+		port@4 {
+			reg = <4>;
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/imx6dl-aristainetos_4.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos_4.dts
index cc861a43eb58..9ec038f1d0ff 100644
--- a/arch/arm/boot/dts/imx6dl-aristainetos_4.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos_4.dts
@@ -14,7 +14,7 @@
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 		enable-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
@@ -36,8 +36,8 @@
 		status = "okay";
 
 		display-timings {
-			480x800p60 {
-				native-mode;
+			native-mode = <&timing0>;
+			timing0: timing-480x800p60 {
 				clock-frequency = <30000000>;
 				hactive = <480>;
 				vactive = <800>;
@@ -79,6 +79,5 @@
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx6dl-aristainetos_7.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos_7.dts
index b6cb78870cd5..b3129832f471 100644
--- a/arch/arm/boot/dts/imx6dl-aristainetos_7.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-aristainetos_7.dts
@@ -25,8 +25,8 @@
 		status = "okay";
 
 		display-timings {
-			800x480p60 {
-				native-mode;
+			native-mode = <&timing0>;
+			timing0: timing-800x480p60 {
 				clock-frequency = <33246000>;
 				hactive = <800>;
 				vactive = <480>;
@@ -49,7 +49,7 @@
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm3 0 3000>;
+		pwms = <&pwm3 0 3000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
 		pinctrl-names = "default";
@@ -69,6 +69,5 @@
 };
 
 &pwm3 {
-	#pwm-cells = <2>;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx6dl-b105pv2.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-b105pv2.dts
index 411aa72d344b..63cdf24eb397 100644
--- a/arch/arm/boot/dts/imx6dl-b105pv2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-b105pv2.dts
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: GPL-2.0 or MIT
+// SPDX-License-Identifier: GPL-2.0 OR MIT
 //
 // Device Tree Source for General Electric B105Pv2
 //
@@ -22,7 +22,7 @@
 		compatible = "ilitek,ili251x";
 		reg = <0x41>;
 		pinctrl-names = "default";
-		pinctrl-0 =<&pinctrl_q7_gpio0>;
+		pinctrl-0 = <&pinctrl_q7_gpio0>;
 		interrupt-parent = <&gpio5>;
 		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
 		reset-gpios = <&tca6424a 21 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/imx6dl-b105v2.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-b105v2.dts
index d011127c635b..2e75d700efdb 100644
--- a/arch/arm/boot/dts/imx6dl-b105v2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-b105v2.dts
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: GPL-2.0 or MIT
+// SPDX-License-Identifier: GPL-2.0 OR MIT
 //
 // Device Tree Source for General Electric B105v2
 //
@@ -22,7 +22,7 @@
 		compatible = "ilitek,ili251x";
 		reg = <0x41>;
 		pinctrl-names = "default";
-		pinctrl-0 =<&pinctrl_q7_gpio0>;
+		pinctrl-0 = <&pinctrl_q7_gpio0>;
 		interrupt-parent = <&gpio5>;
 		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
 		reset-gpios = <&tca6424a 21 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/imx6dl-b125pv2.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-b125pv2.dts
index ca840fa84052..94625d5d5918 100644
--- a/arch/arm/boot/dts/imx6dl-b125pv2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-b125pv2.dts
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: GPL-2.0 or MIT
+// SPDX-License-Identifier: GPL-2.0 OR MIT
 //
 // Device Tree Source for General Electric B125Pv2
 //
@@ -22,7 +22,7 @@
 		compatible = "eeti,exc80h60";
 		reg = <0x2a>;
 		pinctrl-names = "default";
-		pinctrl-0 =<&pinctrl_q7_gpio0>;
+		pinctrl-0 = <&pinctrl_q7_gpio0>;
 		interrupt-parent = <&gpio5>;
 		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 		reset-gpios = <&tca6424a 21 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/imx6dl-b125v2.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-b125v2.dts
index 81e5a9cb8900..b3cfa8110ade 100644
--- a/arch/arm/boot/dts/imx6dl-b125v2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-b125v2.dts
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: GPL-2.0 or MIT
+// SPDX-License-Identifier: GPL-2.0 OR MIT
 //
 // Device Tree Source for General Electric B125v2
 //
@@ -22,7 +22,7 @@
 		compatible = "eeti,exc80h60";
 		reg = <0x2a>;
 		pinctrl-names = "default";
-		pinctrl-0 =<&pinctrl_q7_gpio0>;
+		pinctrl-0 = <&pinctrl_q7_gpio0>;
 		interrupt-parent = <&gpio5>;
 		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 		reset-gpios = <&tca6424a 21 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/imx6dl-b155v2.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-b155v2.dts
index c861937b30f6..7edc788bcb8f 100644
--- a/arch/arm/boot/dts/imx6dl-b155v2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-b155v2.dts
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: GPL-2.0 or MIT
+// SPDX-License-Identifier: GPL-2.0 OR MIT
 //
 // Device Tree Source for General Electric B155v2
 //
@@ -22,7 +22,7 @@
 		compatible = "eeti,exc80h84";
 		reg = <0x2a>;
 		pinctrl-names = "default";
-		pinctrl-0 =<&pinctrl_q7_gpio0>;
+		pinctrl-0 = <&pinctrl_q7_gpio0>;
 		interrupt-parent = <&gpio5>;
 		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 		touchscreen-inverted-x;
diff --git a/arch/arm/boot/dts/imx6dl-b1x5pv2.dtsi b/arch/arm/boot/dts/nxp/imx/imx6dl-b1x5pv2.dtsi
index ec5b66453156..9f1655540cb9 100644
--- a/arch/arm/boot/dts/imx6dl-b1x5pv2.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-b1x5pv2.dtsi
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: GPL-2.0 or MIT
+// SPDX-License-Identifier: GPL-2.0 OR MIT
 //
 // Device Tree Source for General Electric B1x5Pv2
 // patient monitor series
@@ -188,7 +188,7 @@
 	rotary-encoder-key {
 		compatible = "gpio-keys";
 
-		rotary-encoder-press {
+		rotary-encoder-event {
 			label = "rotary-encoder press";
 			gpios = <&tca6424a 0 GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_ENTER>;
@@ -211,17 +211,17 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_q7_gpio1 &pinctrl_q7_gpio3 &pinctrl_q7_gpio5>;
 
-		alarm1 {
+		led-alarm1 {
 			label = "alarm:red";
 			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
 		};
 
-		alarm2 {
+		led-alarm2 {
 			label = "alarm:yellow";
 			gpios = <&gpio4 27 GPIO_ACTIVE_HIGH>;
 		};
 
-		alarm3 {
+		led-alarm3 {
 			label = "alarm:blue";
 			gpios = <&gpio4 15 GPIO_ACTIVE_HIGH>;
 		};
@@ -257,7 +257,7 @@
 		simple-audio-card,bitclock-master = <&dailink_master>;
 		simple-audio-card,frame-master = <&dailink_master>;
 		simple-audio-card,widgets = "Speaker", "Ext Spk";
-		simple-audio-card,audio-routing = "Ext Spk", "LINE";
+		simple-audio-card,routing = "Ext Spk", "LINE";
 
 		simple-audio-card,cpu {
 			sound-dai = <&ssi1>;
diff --git a/arch/arm/boot/dts/imx6dl-b1x5v2.dtsi b/arch/arm/boot/dts/nxp/imx/imx6dl-b1x5v2.dtsi
index f028b6a191df..590dcc0953cc 100644
--- a/arch/arm/boot/dts/imx6dl-b1x5v2.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-b1x5v2.dtsi
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: GPL-2.0 or MIT
+// SPDX-License-Identifier: GPL-2.0 OR MIT
 //
 // Device Tree Source for General Electric B1x5v2
 // patient monitor series
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-aster.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-aster.dts
new file mode 100644
index 000000000000..987058ab0a9b
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-aster.dts
@@ -0,0 +1,114 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx6dl.dtsi"
+#include "imx6qdl-colibri.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6DL/S on Colibri Aster Board";
+	compatible = "toradex,colibri_imx6dl-aster", "toradex,colibri_imx6dl",
+		     "fsl,imx6dl";
+
+	aliases {
+		i2c0 = &i2c2;
+		i2c1 = &i2c3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+/* Colibri SSP */
+&ecspi4 {
+	cs-gpios = <
+		&gpio5 2 GPIO_ACTIVE_HIGH
+		&gpio5 4 GPIO_ACTIVE_HIGH
+	>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi4 &pinctrl_csi_gpio_2>;
+	status = "okay";
+};
+
+/* Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 */
+&i2c3 {
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		&pinctrl_csi_gpio_1
+		&pinctrl_gpio_2
+		&pinctrl_gpio_aster
+		&pinctrl_usbh_oc_1
+		&pinctrl_usbc_id_1
+		&pinctrl_weim_gpio_5
+	>;
+
+	pinctrl_gpio_aster: gpioastergrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL2__GPIO4_IO10		0x1b0b0
+			MX6QDL_PAD_KEY_ROW2__GPIO4_IO11		0x1b0b0
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b0
+			MX6QDL_PAD_NANDF_D1__GPIO2_IO01		0x1b0b0
+			MX6QDL_PAD_NANDF_D3__GPIO2_IO03		0x1b0b0
+			MX6QDL_PAD_NANDF_D6__GPIO2_IO06		0x1b0b0
+			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08		0x1b0b0
+			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11		0x1b0b0
+		>;
+	};
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&pwm2 {
+	status = "okay";
+};
+
+&pwm3 {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+&reg_usb_host_vbus {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&usbh1 {
+	disable-over-current;
+	status = "okay";
+};
+
+&usbotg {
+	disable-over-current;
+	status = "okay";
+};
+
+/* Colibri MMC */
+&usdhc1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-eval-v3.dts
index 7da74e6f46d9..f50a26dd34c0 100644
--- a/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-eval-v3.dts
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2014-2020 Toradex
+ * Copyright 2014-2022 Toradex
  * Copyright 2012 Freescale Semiconductor, Inc.
  * Copyright 2011 Linaro Ltd.
  */
@@ -17,12 +17,6 @@
 	compatible = "toradex,colibri_imx6dl-eval-v3", "toradex,colibri_imx6dl",
 		     "fsl,imx6dl";
 
-	/* Will be filled by the bootloader */
-	memory@10000000 {
-		device_type = "memory";
-		reg = <0x10000000 0>;
-	};
-
 	aliases {
 		i2c0 = &i2c2;
 		i2c1 = &i2c3;
@@ -44,67 +38,6 @@
 		clock-frequency = <16000000>;
 		clock-output-names = "clk16m";
 	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpio_keys>;
-
-		wakeup {
-			label = "Wake-Up";
-			gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>; /* SODIMM 45 */
-			linux,code = <KEY_WAKEUP>;
-			debounce-interval = <10>;
-			wakeup-source;
-		};
-	};
-
-	lcd_display: disp0 {
-		compatible = "fsl,imx-parallel-display";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		interface-pix-fmt = "bgr666";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_ipu1_lcdif>;
-		status = "okay";
-
-		port@0 {
-			reg = <0>;
-
-			lcd_display_in: endpoint {
-				remote-endpoint = <&ipu1_di0_disp0>;
-			};
-		};
-
-		port@1 {
-			reg = <1>;
-
-			lcd_display_out: endpoint {
-				remote-endpoint = <&lcd_panel_in>;
-			};
-		};
-	};
-
-	panel: panel {
-		/*
-		 * edt,et057090dhu: EDT 5.7" LCD TFT
-		 * edt,et070080dh6: EDT 7.0" LCD TFT
-		 */
-		compatible = "edt,et057090dhu";
-		backlight = <&backlight>;
-
-		port {
-			lcd_panel_in: endpoint {
-				remote-endpoint = <&lcd_display_out>;
-			};
-		};
-	};
-};
-
-&backlight {
-	brightness-levels = <0 127 191 223 239 247 251 255>;
-	default-brightness-level = <1>;
-	status = "okay";
 };
 
 /* Colibri SSP */
@@ -113,40 +46,21 @@
 
 	mcp251x0: mcp251x@0 {
 		compatible = "microchip,mcp2515";
-		reg = <0>;
 		clocks = <&clk16m>;
 		interrupt-parent = <&gpio3>;
 		interrupts = <27 0x2>;
+		reg = <0>;
 		spi-max-frequency = <10000000>;
 		status = "okay";
 	};
 };
 
-&hdmi {
-	status = "okay";
-};
-
 /*
  * Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 (e.g. RTC on carrier board)
  */
 &i2c3 {
 	status = "okay";
 
-	/*
-	 * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
-	 * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
-	 */
-	touchscreen@4a {
-		compatible = "atmel,maxtouch";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_pcap_1>;
-		reg = <0x4a>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;		/* SODIMM 28 */
-		reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;	/* SODIMM 30 */
-		status = "disabled";
-	};
-
 	/* M41T0M6 real time clock on carrier board */
 	rtc_i2c: rtc@68 {
 		compatible = "st,m41t0";
@@ -162,24 +76,6 @@
 		&pinctrl_weim_gpio_5 &pinctrl_weim_gpio_6
 		&pinctrl_usbh_oc_1 &pinctrl_usbc_id_1
 	>;
-
-	pinctrl_pcap_1: pcap1grp {
-		fsl,pins = <
-			MX6QDL_PAD_GPIO_9__GPIO1_IO09	0x1b0b0 /* SODIMM 28 */
-			MX6QDL_PAD_SD4_DAT2__GPIO2_IO10	0x1b0b0 /* SODIMM 30 */
-		>;
-	};
-
-	pinctrl_mxt_ts: mxttsgrp {
-		fsl,pins = <
-			MX6QDL_PAD_EIM_CS1__GPIO2_IO24	0x130b0 /* SODIMM 107 */
-			MX6QDL_PAD_SD2_DAT1__GPIO1_IO14	0x130b0 /* SODIMM 106 */
-		>;
-	};
-};
-
-&ipu1_di0_disp0 {
-	remote-endpoint = <&lcd_display_in>;
 };
 
 &pwm1 {
@@ -215,11 +111,12 @@
 };
 
 &usbh1 {
-	vbus-supply = <&reg_usb_host_vbus>;
+	disable-over-current;
 	status = "okay";
 };
 
 &usbotg {
+	disable-over-current;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-iris-v2.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-iris-v2.dts
new file mode 100644
index 000000000000..3a6d3889760d
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-iris-v2.dts
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6dl-colibri-iris.dts"
+
+/ {
+	model = "Toradex Colibri iMX6DL/S on Colibri Iris V2 Board";
+	compatible = "toradex,colibri_imx6dl-iris-v2", "toradex,colibri_imx6dl",
+		     "fsl,imx6dl";
+
+	reg_3v3_vmmc: regulator-3v3-vmmc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_enable_3v3_vmmc>;
+		regulator-name = "3v3_vmmc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <100>;
+		enable-active-high;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio_iris	&pinctrl_usbh_oc_1 &pinctrl_usbc_id_1>;
+
+	pinctrl_enable_3v3_vmmc: enable3v3vmmcgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11	0x1b0b0
+		>;
+	};
+};
+
+/* Colibri MMC */
+&usdhc1 {
+	cap-power-off-card;
+	/* uncomment the following to enable SD card UHS mode if you have a V1.1 module */
+	/* /delete-property/ no-1-8-v; */
+	vmmc-supply = <&reg_3v3_vmmc>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-iris.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-iris.dts
new file mode 100644
index 000000000000..4303c88bb2a9
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-iris.dts
@@ -0,0 +1,153 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx6dl.dtsi"
+#include "imx6qdl-colibri.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6DL/S on Colibri Iris Board";
+	compatible = "toradex,colibri_imx6dl-iris", "toradex,colibri_imx6dl",
+		     "fsl,imx6dl";
+
+	aliases {
+		i2c0 = &i2c2;
+		i2c1 = &i2c3;
+	};
+
+	aliases {
+		rtc0 = &rtc_i2c;
+		rtc1 = &snvs_rtc;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+/* Colibri SSP */
+&ecspi4 {
+	status = "okay";
+};
+
+&gpio2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_forceoff &pinctrl_uart23_forceoff>;
+
+	/*
+	 * uart-a-on-x13-enable turns the UART transceiver for UART_A on. If one
+	 * wants to turn the transceiver off, that property has to be deleted
+	 * and the gpio handled in userspace.
+	 * The same applies to uart-b-c-on-x14-enable where the UART_B and
+	 * UART_C transceiver is turned on.
+	 */
+	uart-a-on-x13-enable-hog {
+		gpio-hog;
+		gpios = <4 GPIO_ACTIVE_HIGH>; /* SODIMM 102 */
+		output-high;
+	};
+
+	uart-b-c-on-x14-enable-hog {
+		gpio-hog;
+		gpios = <8 GPIO_ACTIVE_HIGH>; /* SODIMM 104 */
+		output-high;
+	};
+};
+
+/*
+ * Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 (e.g. RTC on carrier board)
+ */
+&i2c3 {
+	status = "okay";
+
+	rtc_i2c: rtc@68 {
+		compatible = "st,m41t0";
+		reg = <0x68>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		&pinctrl_gpio_iris
+		&pinctrl_usbh_oc_1
+		&pinctrl_usbc_id_1
+	>;
+
+	pinctrl_gpio_iris: gpioirisgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A17__GPIO2_IO21	0x1b0b0
+			MX6QDL_PAD_EIM_A18__GPIO2_IO20	0x1b0b0
+			MX6QDL_PAD_EIM_A19__GPIO2_IO19	0x1b0b0
+			MX6QDL_PAD_EIM_A20__GPIO2_IO18	0x1b0b0
+			MX6QDL_PAD_EIM_A23__GPIO6_IO06	0x1b0b0
+			MX6QDL_PAD_EIM_D27__GPIO3_IO27	0x1b0b0
+			MX6QDL_PAD_NANDF_D3__GPIO2_IO03	0x1b0b0
+			MX6QDL_PAD_SD2_DAT0__GPIO1_IO15	0x1b0b0
+		>;
+	};
+
+	pinctrl_uart1_forceoff: uart1forceoffgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D4__GPIO2_IO04 0x1b0b0
+		>;
+	};
+
+	pinctrl_uart23_forceoff: uart23forceoffgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0
+		>;
+	};
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&pwm2 {
+	status = "okay";
+};
+
+&pwm3 {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+&reg_usb_host_vbus {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&usbh1 {
+	disable-over-current;
+	status = "okay";
+};
+
+&usbotg {
+	disable-over-current;
+	status = "okay";
+};
+
+/* Colibri MMC */
+&usdhc1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-v1.2-aster.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-v1.2-aster.dts
new file mode 100644
index 000000000000..44c78c07f431
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-v1.2-aster.dts
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/* Copyright (c) 2025 Toradex */
+
+/dts-v1/;
+
+#include "imx6dl-colibri-aster.dts"
+#include "imx6qdl-colibri-v1.2.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6DL/S V1.2+ on Colibri Aster Board";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-v1.2-eval-v3.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-v1.2-eval-v3.dts
new file mode 100644
index 000000000000..93fd0af53a3c
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-v1.2-eval-v3.dts
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/* Copyright (c) 2025 Toradex */
+
+/dts-v1/;
+
+#include "imx6dl-colibri-eval-v3.dts"
+#include "imx6qdl-colibri-v1.2.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6DL/S V1.2+ on Colibri Evaluation Board V3";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-v1.2-iris-v2.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-v1.2-iris-v2.dts
new file mode 100644
index 000000000000..92d41fc9a13f
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-v1.2-iris-v2.dts
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/* Copyright (c) 2025 Toradex */
+
+/dts-v1/;
+
+#include "imx6dl-colibri-iris-v2.dts"
+#include "imx6qdl-colibri-v1.2.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6DL/S V1.2+ on Colibri Iris V2 Board";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-v1.2-iris.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-v1.2-iris.dts
new file mode 100644
index 000000000000..c8957948c887
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-colibri-v1.2-iris.dts
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/* Copyright (c) 2025 Toradex */
+
+/dts-v1/;
+
+#include "imx6dl-colibri-iris.dts"
+#include "imx6qdl-colibri-v1.2.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6DL/S V1.2+ on Colibri Iris Board";
+};
diff --git a/arch/arm/boot/dts/imx6dl-cubox-i-emmc-som-v15.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-cubox-i-emmc-som-v15.dts
index 2b2fc360b865..2b2fc360b865 100644
--- a/arch/arm/boot/dts/imx6dl-cubox-i-emmc-som-v15.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-cubox-i-emmc-som-v15.dts
diff --git a/arch/arm/boot/dts/imx6dl-cubox-i-som-v15.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-cubox-i-som-v15.dts
index e09c565d1d1f..e09c565d1d1f 100644
--- a/arch/arm/boot/dts/imx6dl-cubox-i-som-v15.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-cubox-i-som-v15.dts
diff --git a/arch/arm/boot/dts/imx6dl-cubox-i.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-cubox-i.dts
index 2b1b3e193f53..2b1b3e193f53 100644
--- a/arch/arm/boot/dts/imx6dl-cubox-i.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-cubox-i.dts
diff --git a/arch/arm/boot/dts/imx6dl-dfi-fs700-m60.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-dfi-fs700-m60.dts
index cece4aafdad8..cece4aafdad8 100644
--- a/arch/arm/boot/dts/imx6dl-dfi-fs700-m60.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-dfi-fs700-m60.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-dhcom-pdk2.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-dhcom-pdk2.dts
new file mode 100644
index 000000000000..38235925257a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-dhcom-pdk2.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2024 Marek Vasut <marex@denx.de>
+ *
+ * DHCOM iMX6 variant:
+ * DHCM-iMX6DL-C080-R102-F0819-E-SD-RTC-T-HS-I-01D2
+ * DHCOM PCB number: 493-400 or newer
+ * PDK2 PCB number: 516-400 or newer
+ */
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-dhcom-som.dtsi"
+#include "imx6qdl-dhcom-pdk2.dtsi"
+
+/ {
+	model = "DH electronics i.MX6DL DHCOM on Premium Developer Kit (2)";
+	compatible = "dh,imx6dl-dhcom-pdk2", "dh,imx6dl-dhcom-som",
+		     "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/imx6dl-dhcom-picoitx.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-dhcom-picoitx.dts
index 038bb0025556..775caf8208c5 100644
--- a/arch/arm/boot/dts/imx6dl-dhcom-picoitx.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-dhcom-picoitx.dts
@@ -3,7 +3,7 @@
  * Copyright (C) 2021 DH electronics GmbH
  *
  * DHCOM iMX6 variant:
- * DHCM-iMX6DL-C0800-R102-F0819-E-SD-RTC-T-HS-I-01D2
+ * DHCM-iMX6DL-C080-R102-F0819-E-SD-RTC-T-HS-I-01D2
  * DHCOM PCB number: 493-300 or newer
  * PicoITX PCB number: 487-600 or newer
  */
diff --git a/arch/arm/boot/dts/imx6dl-eckelmann-ci4x10.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-eckelmann-ci4x10.dts
index b4a9523e325b..5ed55f74b398 100644
--- a/arch/arm/boot/dts/imx6dl-eckelmann-ci4x10.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-eckelmann-ci4x10.dts
@@ -28,6 +28,7 @@
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <50000000>;
+		clock-output-names = "enet_ref_pad";
 	};
 
 	reg_usb_h1_vbus: regulator-usb-h1-vbus {
@@ -64,6 +65,13 @@
 	status = "okay";
 };
 
+&clks {
+	clocks = <&rmii_clk>;
+	clock-names = "enet_ref_pad";
+	assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&rmii_clk>;
+};
+
 &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi2>;
@@ -131,7 +139,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hog>;
 
-	pinctrl_hog: hog {
+	pinctrl_hog: hoggrp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D0__GPIO2_IO00		0x00000018 /* buzzer */
 			MX6QDL_PAD_KEY_COL1__GPIO4_IO08		0x00000018 /* OUT_1 */
@@ -297,7 +305,6 @@
 	phy-mode = "rmii";
 	phy-reset-gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
 	phy-handle = <&phy>;
-	clocks = <&clks IMX6QDL_CLK_ENET>, <&clks IMX6QDL_CLK_ENET>, <&rmii_clk>;
 	status = "okay";
 
 	mdio {
diff --git a/arch/arm/boot/dts/imx6dl-emcon-avari.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-emcon-avari.dts
index 407ad8d43c84..77d7600b2675 100644
--- a/arch/arm/boot/dts/imx6dl-emcon-avari.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-emcon-avari.dts
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: (GPL-2.0 or MIT)
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
 //
 // Copyright (C) 2018 emtrion GmbH
 //
diff --git a/arch/arm/boot/dts/imx6dl-gw51xx.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw51xx.dts
index 9956d12a1245..9956d12a1245 100644
--- a/arch/arm/boot/dts/imx6dl-gw51xx.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw51xx.dts
diff --git a/arch/arm/boot/dts/imx6dl-gw52xx.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw52xx.dts
index 9ea23dd54f3c..9ea23dd54f3c 100644
--- a/arch/arm/boot/dts/imx6dl-gw52xx.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw52xx.dts
diff --git a/arch/arm/boot/dts/imx6dl-gw53xx.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw53xx.dts
index 182e8194c249..182e8194c249 100644
--- a/arch/arm/boot/dts/imx6dl-gw53xx.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw53xx.dts
diff --git a/arch/arm/boot/dts/imx6dl-gw54xx.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw54xx.dts
index a106c4e3e329..a106c4e3e329 100644
--- a/arch/arm/boot/dts/imx6dl-gw54xx.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw54xx.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-gw551x.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw551x.dts
new file mode 100644
index 000000000000..50dd3df9dd04
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw551x.dts
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2014 Gateworks Corporation
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-gw551x.dtsi"
+
+/ {
+	model = "Gateworks Ventana i.MX6 DualLite/Solo GW551X";
+	compatible = "gw,imx6dl-gw551x", "gw,ventana", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/imx6dl-gw552x.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw552x.dts
index 4864a36f9b36..4864a36f9b36 100644
--- a/arch/arm/boot/dts/imx6dl-gw552x.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw552x.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-gw553x.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw553x.dts
new file mode 100644
index 000000000000..8ca5b6b8da07
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw553x.dts
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2016 Gateworks Corporation
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-gw553x.dtsi"
+
+/ {
+	model = "Gateworks Ventana i.MX6 DualLite/Solo GW553X";
+	compatible = "gw,imx6dl-gw553x", "gw,ventana", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-gw560x.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw560x.dts
new file mode 100644
index 000000000000..b94455406a57
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw560x.dts
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2017 Gateworks Corporation
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-gw560x.dtsi"
+
+/ {
+	model = "Gateworks Ventana i.MX6 DualLite/Solo GW560X";
+	compatible = "gw,imx6dl-gw560x", "gw,ventana", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-gw5903.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw5903.dts
new file mode 100644
index 000000000000..dd978105b42f
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw5903.dts
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2017 Gateworks Corporation
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-gw5903.dtsi"
+
+/ {
+	model = "Gateworks Ventana i.MX6 Duallite/Solo GW5903";
+	compatible = "gw,imx6dl-gw5903", "gw,ventana", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-gw5904.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw5904.dts
new file mode 100644
index 000000000000..172dad423639
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw5904.dts
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2017 Gateworks Corporation
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-gw5904.dtsi"
+
+/ {
+	model = "Gateworks Ventana i.MX6 DualLite/Solo GW5904";
+	compatible = "gw,imx6dl-gw5904", "gw,ventana", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/imx6dl-gw5907.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw5907.dts
index 3fa2822beffc..3fa2822beffc 100644
--- a/arch/arm/boot/dts/imx6dl-gw5907.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw5907.dts
diff --git a/arch/arm/boot/dts/imx6dl-gw5910.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw5910.dts
index 0d5e7e5da536..0d5e7e5da536 100644
--- a/arch/arm/boot/dts/imx6dl-gw5910.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw5910.dts
diff --git a/arch/arm/boot/dts/imx6dl-gw5912.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw5912.dts
index 5260e0142d63..5260e0142d63 100644
--- a/arch/arm/boot/dts/imx6dl-gw5912.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw5912.dts
diff --git a/arch/arm/boot/dts/imx6dl-gw5913.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-gw5913.dts
index b74e533c8e67..b74e533c8e67 100644
--- a/arch/arm/boot/dts/imx6dl-gw5913.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-gw5913.dts
diff --git a/arch/arm/boot/dts/imx6dl-hummingboard-emmc-som-v15.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-hummingboard-emmc-som-v15.dts
index a63f742f20d9..a63f742f20d9 100644
--- a/arch/arm/boot/dts/imx6dl-hummingboard-emmc-som-v15.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-hummingboard-emmc-som-v15.dts
diff --git a/arch/arm/boot/dts/imx6dl-hummingboard-som-v15.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-hummingboard-som-v15.dts
index 66a06cf3cdf3..66a06cf3cdf3 100644
--- a/arch/arm/boot/dts/imx6dl-hummingboard-som-v15.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-hummingboard-som-v15.dts
diff --git a/arch/arm/boot/dts/imx6dl-hummingboard.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-hummingboard.dts
index cbd02eb486e1..cbd02eb486e1 100644
--- a/arch/arm/boot/dts/imx6dl-hummingboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-hummingboard.dts
diff --git a/arch/arm/boot/dts/imx6dl-hummingboard2-emmc-som-v15.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-hummingboard2-emmc-som-v15.dts
index 80313c13bcdb..80313c13bcdb 100644
--- a/arch/arm/boot/dts/imx6dl-hummingboard2-emmc-som-v15.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-hummingboard2-emmc-som-v15.dts
diff --git a/arch/arm/boot/dts/imx6dl-hummingboard2-som-v15.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-hummingboard2-som-v15.dts
index e61ef1156f8b..e61ef1156f8b 100644
--- a/arch/arm/boot/dts/imx6dl-hummingboard2-som-v15.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-hummingboard2-som-v15.dts
diff --git a/arch/arm/boot/dts/imx6dl-hummingboard2.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-hummingboard2.dts
index b12cd87f3f94..b12cd87f3f94 100644
--- a/arch/arm/boot/dts/imx6dl-hummingboard2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-hummingboard2.dts
diff --git a/arch/arm/boot/dts/imx6dl-icore-mipi.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-icore-mipi.dts
index d8f3821a0ffd..d8f3821a0ffd 100644
--- a/arch/arm/boot/dts/imx6dl-icore-mipi.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-icore-mipi.dts
diff --git a/arch/arm/boot/dts/imx6dl-icore-rqs.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-icore-rqs.dts
index 73d710d34b9d..73d710d34b9d 100644
--- a/arch/arm/boot/dts/imx6dl-icore-rqs.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-icore-rqs.dts
diff --git a/arch/arm/boot/dts/imx6dl-icore.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-icore.dts
index 80fa60607ab1..80fa60607ab1 100644
--- a/arch/arm/boot/dts/imx6dl-icore.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-icore.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-kontron-samx6i-ads2.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-kontron-samx6i-ads2.dts
new file mode 100644
index 000000000000..6a0c53f23a15
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-kontron-samx6i-ads2.dts
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: GPL-2.0 OR X11
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-kontron-samx6i.dtsi"
+#include "imx6qdl-kontron-samx6i-ads2.dtsi"
+
+/ {
+	model = "Kontron SMARC-sAMX6i Dual-Lite/Solo on SMARC Eval 2.0 carrier";
+	compatible = "kontron,imx6dl-samx6i-ads2", "kontron,imx6dl-samx6i", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/imx6dl-kontron-samx6i.dtsi b/arch/arm/boot/dts/nxp/imx/imx6dl-kontron-samx6i.dtsi
index a864fdbd5f16..5a9b819d7ee8 100644
--- a/arch/arm/boot/dts/imx6dl-kontron-samx6i.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-kontron-samx6i.dtsi
@@ -7,6 +7,6 @@
 #include "imx6qdl-kontron-samx6i.dtsi"
 
 / {
-	model = "Kontron SMARC sAMX6i Dual-Lite/Solo";
+	model = "Kontron SMARC-sAMX6i Dual-Lite/Solo";
 	compatible = "kontron,imx6dl-samx6i", "fsl,imx6dl";
 };
diff --git a/arch/arm/boot/dts/imx6dl-lanmcu.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-lanmcu.dts
index 6b6e6fcdea9c..7c62db91173b 100644
--- a/arch/arm/boot/dts/imx6dl-lanmcu.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-lanmcu.dts
@@ -21,6 +21,7 @@
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <50000000>;
+		clock-output-names = "enet_ref_pad";
 	};
 
 	backlight: backlight {
@@ -109,14 +110,17 @@
 	status = "okay";
 };
 
+&clks {
+	clocks = <&clock_ksz8081>;
+	clock-names = "enet_ref_pad";
+	assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&clock_ksz8081>;
+};
+
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rmii";
-	clocks = <&clks IMX6QDL_CLK_ENET>,
-		 <&clks IMX6QDL_CLK_ENET>,
-		 <&clock_ksz8081>;
-	clock-names = "ipg", "ahb", "ptp";
 	phy-handle = <&rgmii_phy>;
 	status = "okay";
 
@@ -253,9 +257,18 @@
 	pinctrl-0 = <&pinctrl_usbotg>;
 	phy_type = "utmi";
 	dr_mode = "host";
+	over-current-active-low;
 	status = "okay";
 };
 
+&usbphynop1 {
+	status = "disabled";
+};
+
+&usbphynop2 {
+	status = "disabled";
+};
+
 &usdhc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc1>;
diff --git a/arch/arm/boot/dts/imx6dl-mamoj.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-mamoj.dts
index 028951955bde..ec5a9bf40677 100644
--- a/arch/arm/boot/dts/imx6dl-mamoj.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-mamoj.dts
@@ -21,7 +21,7 @@
 
 	backlight_lcd: backlight-lcd {
 		compatible = "pwm-backlight";
-		pwms = <&pwm3 0 25000>; /* 25000ns -> 40kHz */
+		pwms = <&pwm3 0 25000 0>; /* 25000ns -> 40kHz */
 		brightness-levels = <0 4 8 16 32 64 128 160 192 224 255>;
 		default-brightness-level = <7>;
 	};
@@ -303,7 +303,6 @@
 };
 
 &pwm3 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "okay";
@@ -396,7 +395,7 @@
 		>;
 	};
 
-	pinctrl_ipu1_lcdif: pinctrlipu1lcdif { /* parallel port 24-bit */
+	pinctrl_ipu1_lcdif: pinctrlipu1lcdifgrp { /* parallel port 24-bit */
 		fsl,pins = <
 			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10 /* VDOUT_PCLK */
 			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15       0x10
diff --git a/arch/arm/boot/dts/imx6dl-mba6.dtsi b/arch/arm/boot/dts/nxp/imx/imx6dl-mba6.dtsi
index b749b424bbd6..b749b424bbd6 100644
--- a/arch/arm/boot/dts/imx6dl-mba6.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-mba6.dtsi
diff --git a/arch/arm/boot/dts/imx6dl-mba6a.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-mba6a.dts
index df0a96b28af0..df0a96b28af0 100644
--- a/arch/arm/boot/dts/imx6dl-mba6a.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-mba6a.dts
diff --git a/arch/arm/boot/dts/imx6dl-mba6b.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-mba6b.dts
index 610b19d2db0f..610b19d2db0f 100644
--- a/arch/arm/boot/dts/imx6dl-mba6b.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-mba6b.dts
diff --git a/arch/arm/boot/dts/imx6dl-nit6xlite.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-nit6xlite.dts
index 61fa30991d67..61fa30991d67 100644
--- a/arch/arm/boot/dts/imx6dl-nit6xlite.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-nit6xlite.dts
diff --git a/arch/arm/boot/dts/imx6dl-nitrogen6x.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-nitrogen6x.dts
index ef58d3b0ea0d..ef58d3b0ea0d 100644
--- a/arch/arm/boot/dts/imx6dl-nitrogen6x.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-nitrogen6x.dts
diff --git a/arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-phytec-mira-rdk-nand.dts
index d906a7f05aaa..d906a7f05aaa 100644
--- a/arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-phytec-mira-rdk-nand.dts
diff --git a/arch/arm/boot/dts/imx6dl-phytec-pbab01.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-phytec-pbab01.dts
index 0a07cc6f815e..0a07cc6f815e 100644
--- a/arch/arm/boot/dts/imx6dl-phytec-pbab01.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-phytec-pbab01.dts
diff --git a/arch/arm/boot/dts/imx6dl-phytec-pfla02.dtsi b/arch/arm/boot/dts/nxp/imx/imx6dl-phytec-pfla02.dtsi
index 6f8aaf524425..6f8aaf524425 100644
--- a/arch/arm/boot/dts/imx6dl-phytec-pfla02.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-phytec-pfla02.dtsi
diff --git a/arch/arm/boot/dts/imx6dl-pico-dwarf.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-pico-dwarf.dts
index d85b15a8c127..d85b15a8c127 100644
--- a/arch/arm/boot/dts/imx6dl-pico-dwarf.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-pico-dwarf.dts
diff --git a/arch/arm/boot/dts/imx6dl-pico-hobbit.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-pico-hobbit.dts
index 08fedcbcc91b..08fedcbcc91b 100644
--- a/arch/arm/boot/dts/imx6dl-pico-hobbit.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-pico-hobbit.dts
diff --git a/arch/arm/boot/dts/imx6dl-pico-nymph.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-pico-nymph.dts
index 32ccfc5d41ce..32ccfc5d41ce 100644
--- a/arch/arm/boot/dts/imx6dl-pico-nymph.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-pico-nymph.dts
diff --git a/arch/arm/boot/dts/imx6dl-pico-pi.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-pico-pi.dts
index 4590e8ad9a91..4590e8ad9a91 100644
--- a/arch/arm/boot/dts/imx6dl-pico-pi.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-pico-pi.dts
diff --git a/arch/arm/boot/dts/imx6dl-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx6dl-pinfunc.h
index 9d88d09f9bf6..9d88d09f9bf6 100644
--- a/arch/arm/boot/dts/imx6dl-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-pinfunc.h
diff --git a/arch/arm/boot/dts/imx6dl-plybas.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-plybas.dts
index bf72a67a9c76..84f34da06267 100644
--- a/arch/arm/boot/dts/imx6dl-plybas.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-plybas.dts
@@ -75,6 +75,7 @@
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <50000000>;
+		clock-output-names = "enet_ref_pad";
 	};
 
 	reg_5v0: regulator-5v0 {
@@ -99,6 +100,13 @@
 	status = "okay";
 };
 
+&clks {
+	clocks = <&clk50m_phy>;
+	clock-names = "enet_ref_pad";
+	assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&clk50m_phy>;
+};
+
 &ecspi1 {
 	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
@@ -116,10 +124,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rmii";
-	clocks = <&clks IMX6QDL_CLK_ENET>,
-		 <&clks IMX6QDL_CLK_ENET>,
-		 <&clk50m_phy>;
-	clock-names = "ipg", "ahb", "ptp";
 	phy-handle = <&rgmii_phy>;
 	status = "okay";
 
@@ -214,7 +218,7 @@
 &uart2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart2>;
-	fsl,uart-has-rtscts;
+	uart-has-rtscts;
 	linux,rs485-enabled-at-boot-time;
 	rs485-rts-delay = <0 20>;
 	status = "okay";
@@ -231,7 +235,7 @@
 	pinctrl-0 = <&pinctrl_usbotg>;
 	phy_type = "utmi";
 	dr_mode = "host";
-	disable-over-current;
+	over-current-active-low;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-plym2m.dts
index c4ce23d8ac9f..dfa8110b1d97 100644
--- a/arch/arm/boot/dts/imx6dl-plym2m.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-plym2m.dts
@@ -84,6 +84,7 @@
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <50000000>;
+		clock-output-names = "enet_ref_pad";
 	};
 
 	reg_3v3: regulator-3v3 {
@@ -112,18 +113,42 @@
 			polling-delay = <20000>;
 			polling-delay-passive = <0>;
 			thermal-sensors = <&tsens0>;
+
+			trips {
+				alert {
+					temperature = <85000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+			};
 		};
 
 		touch-thermal0 {
 			polling-delay = <20000>;
 			polling-delay-passive = <0>;
 			thermal-sensors = <&touch_temp0>;
+
+			trips {
+				alert {
+					temperature = <85000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+			};
 		};
 
 		touch-thermal1 {
 			polling-delay = <20000>;
 			polling-delay-passive = <0>;
 			thermal-sensors = <&touch_temp1>;
+
+			trips {
+				alert {
+					temperature = <85000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+			};
 		};
 	};
 
@@ -173,6 +198,13 @@
 	status = "okay";
 };
 
+&clks {
+	clocks = <&clk50m_phy>;
+	clock-names = "enet_ref_pad";
+	assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&clk50m_phy>;
+};
+
 &ecspi1 {
 	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
@@ -196,7 +228,7 @@
 		compatible = "ti,tsc2046e-adc";
 		reg = <0>;
 		pinctrl-0 = <&pinctrl_tsc2046>;
-		pinctrl-names ="default";
+		pinctrl-names = "default";
 		spi-max-frequency = <1000000>;
 		interrupts-extended = <&gpio3 20 IRQ_TYPE_LEVEL_LOW>;
 		#io-channel-cells = <1>;
@@ -254,10 +286,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rmii";
-	clocks = <&clks IMX6QDL_CLK_ENET>,
-		 <&clks IMX6QDL_CLK_ENET>,
-		 <&clk50m_phy>;
-	clock-names = "ipg", "ahb", "ptp";
 	phy-handle = <&rgmii_phy>;
 	status = "okay";
 
diff --git a/arch/arm/boot/dts/imx6dl-prtmvt.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-prtmvt.dts
index a35a1c66e770..2160b7177835 100644
--- a/arch/arm/boot/dts/imx6dl-prtmvt.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-prtmvt.dts
@@ -51,98 +51,98 @@
 		pinctrl-0 = <&pinctrl_gpiokeys>;
 		autorepeat;
 
-		power {
+		key-power {
 			label = "Power Button";
 			gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			wakeup-source;
 		};
 
-		f1 {
+		key-f1 {
 			label = "GPIO Key F1";
 			linux,code = <KEY_F1>;
 			gpios = <&gpio_pca 0 GPIO_ACTIVE_LOW>;
 		};
 
-		f2 {
+		key-f2 {
 			label = "GPIO Key F2";
 			linux,code = <KEY_F2>;
 			gpios = <&gpio_pca 1 GPIO_ACTIVE_LOW>;
 		};
 
-		f3 {
+		key-f3 {
 			label = "GPIO Key F3";
 			linux,code = <KEY_F3>;
 			gpios = <&gpio_pca 2 GPIO_ACTIVE_LOW>;
 		};
 
-		f4 {
+		key-f4 {
 			label = "GPIO Key F4";
 			linux,code = <KEY_F4>;
 			gpios = <&gpio_pca 3 GPIO_ACTIVE_LOW>;
 		};
 
-		f5 {
+		key-f5 {
 			label = "GPIO Key F5";
 			linux,code = <KEY_F5>;
 			gpios = <&gpio_pca 4 GPIO_ACTIVE_LOW>;
 		};
 
-		cycle {
+		key-cycle {
 			label = "GPIO Key CYCLE";
 			linux,code = <KEY_CYCLEWINDOWS>;
 			gpios = <&gpio_pca 5 GPIO_ACTIVE_LOW>;
 		};
 
-		esc {
+		key-esc {
 			label = "GPIO Key ESC";
 			linux,code = <KEY_ESC>;
 			gpios = <&gpio_pca 6 GPIO_ACTIVE_LOW>;
 		};
 
-		up {
+		key-up {
 			label = "GPIO Key UP";
 			linux,code = <KEY_UP>;
 			gpios = <&gpio_pca 7 GPIO_ACTIVE_LOW>;
 		};
 
-		down {
+		key-down {
 			label = "GPIO Key DOWN";
 			linux,code = <KEY_DOWN>;
 			gpios = <&gpio_pca 8 GPIO_ACTIVE_LOW>;
 		};
 
-		ok {
+		key-ok {
 			label = "GPIO Key OK";
 			linux,code = <KEY_OK>;
 			gpios = <&gpio_pca 9 GPIO_ACTIVE_LOW>;
 		};
 
-		f6 {
+		key-f6 {
 			label = "GPIO Key F6";
 			linux,code = <KEY_F6>;
 			gpios = <&gpio_pca 10 GPIO_ACTIVE_LOW>;
 		};
 
-		f7 {
+		key-f7 {
 			label = "GPIO Key F7";
 			linux,code = <KEY_F7>;
 			gpios = <&gpio_pca 11 GPIO_ACTIVE_LOW>;
 		};
 
-		f8 {
+		key-f8 {
 			label = "GPIO Key F8";
 			linux,code = <KEY_F8>;
 			gpios = <&gpio_pca 12 GPIO_ACTIVE_LOW>;
 		};
 
-		f9 {
+		key-f9 {
 			label = "GPIO Key F9";
 			linux,code = <KEY_F9>;
 			gpios = <&gpio_pca 13 GPIO_ACTIVE_LOW>;
 		};
 
-		f10 {
+		key-f10 {
 			label = "GPIO Key F10";
 			linux,code = <KEY_F10>;
 			gpios = <&gpio_pca 14 GPIO_ACTIVE_LOW>;
@@ -193,6 +193,7 @@
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <50000000>;
+		clock-output-names = "enet_ref_pad";
 	};
 
 	reg_1v8: regulator-1v8 {
@@ -293,8 +294,10 @@
 };
 
 &clks {
-	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
-	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
+	clocks = <&clk50m_phy>;
+	clock-names = "enet_ref_pad";
+	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>, <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>, <&clk50m_phy>;
 };
 
 &ecspi1 {
@@ -314,10 +317,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rmii";
-	clocks = <&clks IMX6QDL_CLK_ENET>,
-		 <&clks IMX6QDL_CLK_ENET>,
-		 <&clk50m_phy>;
-	clock-names = "ipg", "ahb", "ptp";
 	phy-handle = <&rmii_phy>;
 	status = "okay";
 
@@ -558,9 +557,9 @@
 
 &usbh1 {
 	vbus-supply = <&reg_h1_vbus>;
-	pinctrl-names = "default";
 	phy_type = "utmi";
 	dr_mode = "host";
+	disable-over-current;
 	status = "okay";
 };
 
@@ -570,10 +569,18 @@
 	pinctrl-0 = <&pinctrl_usbotg>;
 	phy_type = "utmi";
 	dr_mode = "host";
-	disable-over-current;
+	over-current-active-low;
 	status = "okay";
 };
 
+&usbphynop1 {
+	status = "disabled";
+};
+
+&usbphynop2 {
+	status = "disabled";
+};
+
 &usdhc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc1>;
@@ -765,7 +772,7 @@
 		>;
 	};
 
-	pinctrl_pca9539: pca9539 {
+	pinctrl_pca9539: pca9539grp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_19__GPIO4_IO05			0x1b0b0
 		>;
diff --git a/arch/arm/boot/dts/imx6dl-prtrvt.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-prtrvt.dts
index 56bb1ca56a2d..e543c4f2bc94 100644
--- a/arch/arm/boot/dts/imx6dl-prtrvt.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-prtrvt.dts
@@ -124,12 +124,16 @@
 	status = "disabled";
 };
 
+&usbotg {
+	disable-over-current;
+};
+
 &vpu {
 	status = "disabled";
 };
 
 &iomuxc {
-	pinctrl_can1phy: can1phy {
+	pinctrl_can1phy: can1phygrp {
 		fsl,pins = <
 			/* CAN1_SR */
 			MX6QDL_PAD_KEY_COL3__GPIO4_IO12	0x13070
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-prtvt7.dts
index b86deebef7b7..29dc6875ab66 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-prtvt7.dts
@@ -24,7 +24,7 @@
 		compatible = "pwm-backlight";
 		pwms = <&pwm1 0 500000 0>;
 		brightness-levels = <0 20 81 248 1000>;
-		default-brightness-level = <20>;
+		default-brightness-level = <65>;
 		num-interpolated-steps = <21>;
 		power-supply = <&reg_bl_12v0>;
 	};
@@ -62,91 +62,91 @@
 		compatible = "gpio-keys";
 		autorepeat;
 
-		esc {
+		key-esc {
 			label = "GPIO Key ESC";
 			linux,code = <KEY_ESC>;
 			gpios = <&gpio_pca 0 GPIO_ACTIVE_LOW>;
 		};
 
-		up {
+		key-up {
 			label = "GPIO Key UP";
 			linux,code = <KEY_UP>;
 			gpios = <&gpio_pca 1 GPIO_ACTIVE_LOW>;
 		};
 
-		down {
+		key-down {
 			label = "GPIO Key DOWN";
 			linux,code = <KEY_DOWN>;
 			gpios = <&gpio_pca 4 GPIO_ACTIVE_LOW>;
 		};
 
-		enter {
+		key-enter {
 			label = "GPIO Key Enter";
 			linux,code = <KEY_ENTER>;
 			gpios = <&gpio_pca 3 GPIO_ACTIVE_LOW>;
 		};
 
-		cycle {
+		key-cycle {
 			label = "GPIO Key CYCLE";
 			linux,code = <KEY_CYCLEWINDOWS>;
 			gpios = <&gpio_pca 2 GPIO_ACTIVE_LOW>;
 		};
 
-		f1 {
+		key-f1 {
 			label = "GPIO Key F1";
 			linux,code = <KEY_F1>;
 			gpios = <&gpio_pca 14 GPIO_ACTIVE_LOW>;
 		};
 
-		f2 {
+		key-f2 {
 			label = "GPIO Key F2";
 			linux,code = <KEY_F2>;
 			gpios = <&gpio_pca 13 GPIO_ACTIVE_LOW>;
 		};
 
-		f3 {
+		key-f3 {
 			label = "GPIO Key F3";
 			linux,code = <KEY_F3>;
 			gpios = <&gpio_pca 12 GPIO_ACTIVE_LOW>;
 		};
 
-		f4 {
+		key-f4 {
 			label = "GPIO Key F4";
 			linux,code = <KEY_F4>;
 			gpios = <&gpio_pca 11 GPIO_ACTIVE_LOW>;
 		};
 
-		f5 {
+		key-f5 {
 			label = "GPIO Key F5";
 			linux,code = <KEY_F5>;
 			gpios = <&gpio_pca 10 GPIO_ACTIVE_LOW>;
 		};
 
-		f6 {
+		key-f6 {
 			label = "GPIO Key F6";
 			linux,code = <KEY_F6>;
 			gpios = <&gpio_pca 5 GPIO_ACTIVE_LOW>;
 		};
 
-		f7 {
+		key-f7 {
 			label = "GPIO Key F7";
 			linux,code = <KEY_F7>;
 			gpios = <&gpio_pca 6 GPIO_ACTIVE_LOW>;
 		};
 
-		f8 {
+		key-f8 {
 			label = "GPIO Key F8";
 			linux,code = <KEY_F8>;
 			gpios = <&gpio_pca 7 GPIO_ACTIVE_LOW>;
 		};
 
-		f9 {
+		key-f9 {
 			label = "GPIO Key F9";
 			linux,code = <KEY_F9>;
 			gpios = <&gpio_pca 8 GPIO_ACTIVE_LOW>;
 		};
 
-		f10 {
+		key-f10 {
 			label = "GPIO Key F10";
 			linux,code = <KEY_F10>;
 			gpios = <&gpio_pca 9 GPIO_ACTIVE_LOW>;
@@ -246,18 +246,42 @@
 			polling-delay = <20000>;
 			polling-delay-passive = <0>;
 			thermal-sensors = <&tsens0>;
+
+			trips {
+				alert {
+					temperature = <105000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+			};
 		};
 
 		touch-thermal0 {
 			polling-delay = <20000>;
 			polling-delay-passive = <0>;
 			thermal-sensors = <&touch_temp0>;
+
+			trips {
+				alert {
+					temperature = <105000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+			};
 		};
 
 		touch-thermal1 {
 			polling-delay = <20000>;
 			polling-delay-passive = <0>;
 			thermal-sensors = <&touch_temp1>;
+
+			trips {
+				alert {
+					temperature = <105000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+			};
 		};
 	};
 
@@ -267,8 +291,6 @@
                               <&adc_ts 5>;
 		io-channel-names = "y", "z1", "z2", "x";
 		touchscreen-min-pressure = <64687>;
-		touchscreen-inverted-x;
-		touchscreen-inverted-y;
 		touchscreen-x-plate-ohms = <300>;
 		touchscreen-y-plate-ohms = <800>;
 	};
@@ -344,7 +366,7 @@
 		compatible = "ti,tsc2046e-adc";
 		reg = <0>;
 		pinctrl-0 = <&pinctrl_tsc>;
-		pinctrl-names ="default";
+		pinctrl-names = "default";
 		spi-max-frequency = <1000000>;
 		interrupts-extended = <&gpio3 20 IRQ_TYPE_LEVEL_LOW>;
 		#io-channel-cells = <1>;
@@ -485,7 +507,7 @@
 		>;
 	};
 
-	pinctrl_can1phy: can1phy {
+	pinctrl_can1phy: can1phygrp {
 		fsl,pins = <
 			/* CAN1_SR */
 			MX6QDL_PAD_KEY_COL3__GPIO4_IO12		0x13070
diff --git a/arch/arm/boot/dts/imx6dl-qmx6.dtsi b/arch/arm/boot/dts/nxp/imx/imx6dl-qmx6.dtsi
index 150d69858255..7a3b96315eaf 100644
--- a/arch/arm/boot/dts/imx6dl-qmx6.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-qmx6.dtsi
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: GPL-2.0 or MIT
+// SPDX-License-Identifier: GPL-2.0 OR MIT
 //
 // Device Tree Source for i.MX6DL based congatec QMX6
 // System on Module
@@ -48,7 +48,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_audmux>;
 
-	audmux_ssi1 {
+	mux-ssi1 {
 		fsl,audmux-port = <MX51_AUDMUX_PORT1_SSI0>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_TFSDIR |
@@ -60,7 +60,7 @@
 		>;
 	};
 
-	audmux_aud6 {
+	mux-aud6 {
 		fsl,audmux-port = <MX51_AUDMUX_PORT6>;
 		fsl,port-config = <
 			IMX_AUDMUX_V2_PTCR_SYN
@@ -157,7 +157,7 @@
 	sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 
-	rtc: m41t62@68 {
+	rtc: rtc@68 {
 		compatible = "st,m41t62";
 		reg = <0x68>;
 
@@ -352,261 +352,259 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hog>;
 
-	qmx6mux: imx6qdl-qmx6 {
-		pinctrl_audmux: audmuxgrp {
-			fsl,pins = <
-				MX6QDL_PAD_DI0_PIN2__AUD6_TXD		0x110b0 /* Q7[67] HDA_SDO */
-				MX6QDL_PAD_DI0_PIN3__AUD6_TXFS		0x30b0 /* Q7[59] HDA_SYNC */
-				MX6QDL_PAD_DI0_PIN4__AUD6_RXD		0x30b0 /* Q7[65] HDA_SDI */
-				MX6QDL_PAD_DI0_PIN15__AUD6_TXC		0x30b0 /* Q7[63] HDA_BITCLK */
-			>;
-		};
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_PIN2__AUD6_TXD		0x110b0 /* Q7[67] HDA_SDO */
+			MX6QDL_PAD_DI0_PIN3__AUD6_TXFS		0x30b0 /* Q7[59] HDA_SYNC */
+			MX6QDL_PAD_DI0_PIN4__AUD6_RXD		0x30b0 /* Q7[65] HDA_SDI */
+			MX6QDL_PAD_DI0_PIN15__AUD6_TXC		0x30b0 /* Q7[63] HDA_BITCLK */
+		>;
+	};
 
-		/* PHY is on System on Module, Q7[3-15] have Ethernet lines */
-		pinctrl_enet: enet {
-			fsl,pins = <
-				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
-				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
-				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
-				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
-				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
-				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
-				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
-				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
-				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
-				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
-				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
-				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
-				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
-				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
-				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
-				MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN	0x1b0b0
-			>;
-		};
+	/* PHY is on System on Module, Q7[3-15] have Ethernet lines */
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN	0x1b0b0
+		>;
+	};
 
-		pinctrl_hog: hoggrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x80000000 /* PCIE_WAKE_B */
-				MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09	0x80000000 /* I2C multiplexer */
-				MX6QDL_PAD_NANDF_D6__GPIO2_IO06		0x80000000 /* SD4_CD# */
-				MX6QDL_PAD_NANDF_D7__GPIO2_IO07		0x80000000 /* SD4_WP */
-				MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1		0x80000000 /* Camera MCLK */
-			>;
-		};
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x80000000 /* PCIE_WAKE_B */
+			MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09	0x80000000 /* I2C multiplexer */
+			MX6QDL_PAD_NANDF_D6__GPIO2_IO06		0x80000000 /* SD4_CD# */
+			MX6QDL_PAD_NANDF_D7__GPIO2_IO07		0x80000000 /* SD4_WP */
+			MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1		0x80000000 /* Camera MCLK */
+		>;
+	};
 
-		pinctrl_i2c1: i2c1 {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1 /* Q7[66] I2C_CLK */
-				MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1 /* Q7[68] I2C_DAT */
-			>;
-		};
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1 /* Q7[66] I2C_CLK */
+			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1 /* Q7[68] I2C_DAT */
+		>;
+	};
 
-		pinctrl_i2c1_gpio: i2c1-gpio {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D21__GPIO3_IO21		0x1b0b0 /* Q7[66] I2C_CLK */
-				MX6QDL_PAD_EIM_D28__GPIO3_IO28		0x1b0b0 /* Q7[68] I2C_DAT */
-			>;
-		};
+	pinctrl_i2c1_gpio: i2c1-gpiogrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__GPIO3_IO21		0x1b0b0 /* Q7[66] I2C_CLK */
+			MX6QDL_PAD_EIM_D28__GPIO3_IO28		0x1b0b0 /* Q7[68] I2C_DAT */
+		>;
+	};
 
-		pinctrl_i2c2: i2c2 {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1 /* Q7[152] SDVO_CTRL_CLK */
-				MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1 /* Q7[150] SDVO_CTRL_DAT */
-			>;
-		};
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1 /* Q7[152] SDVO_CTRL_CLK */
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1 /* Q7[150] SDVO_CTRL_DAT */
+		>;
+	};
 
-		pinctrl_i2c2_gpio: i2c2-gpio {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL3__GPIO4_IO12		0x1b0b0 /* Q7[152] SDVO_CTRL_CLK */
-				MX6QDL_PAD_KEY_ROW3__GPIO4_IO13		0x1b0b0 /* Q7[150] SDVO_CTRL_DAT */
-			>;
-		};
+	pinctrl_i2c2_gpio: i2c2-gpiogrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__GPIO4_IO12		0x1b0b0 /* Q7[152] SDVO_CTRL_CLK */
+			MX6QDL_PAD_KEY_ROW3__GPIO4_IO13		0x1b0b0 /* Q7[150] SDVO_CTRL_DAT */
+		>;
+	};
 
-		pinctrl_i2c3: i2c3 {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_3__I2C3_SCL		0x4001b8b1 /* Q7[60] SMB_CLK */
-				MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1 /* Q7[62] SMB_DAT */
-			>;
-		};
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_3__I2C3_SCL		0x4001b8b1 /* Q7[60] SMB_CLK */
+			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1 /* Q7[62] SMB_DAT */
+		>;
+	};
 
-		pinctrl_i2c3_gpio: i2c3-gpio {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_3__GPIO1_IO03		0x1b0b0 /* Q7[60] SMB_CLK */
-				MX6QDL_PAD_GPIO_6__GPIO1_IO06		0x1b0b0 /* Q7[62] SMB_DAT */
-			>;
-		};
+	pinctrl_i2c3_gpio: i2c3-gpiogrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_3__GPIO1_IO03		0x1b0b0 /* Q7[60] SMB_CLK */
+			MX6QDL_PAD_GPIO_6__GPIO1_IO06		0x1b0b0 /* Q7[62] SMB_DAT */
+		>;
+	};
 
-		pinctrl_phy_reset: phy-reset {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D23__GPIO3_IO23		0x1b0b0 /* RGMII Phy Reset */
-			>;
-		};
+	pinctrl_phy_reset: phy-resetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D23__GPIO3_IO23		0x1b0b0 /* RGMII Phy Reset */
+		>;
+	};
 
-		pinctrl_pwm4: pwm4 {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_CMD__PWM4_OUT		0x1b0b1 /* Q7[123] LVDS_BLT_CTRL */
-			>;
-		};
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__PWM4_OUT		0x1b0b1 /* Q7[123] LVDS_BLT_CTRL */
+		>;
+	};
 
-		pinctrl_q7_backlight_enable: q7-backlight-enable {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_9__GPIO1_IO09		0x1b0b0 /* Q7[112] LVDS_BLEN */
-			>;
-		};
+	pinctrl_q7_backlight_enable: q7-backlight-enablegrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__GPIO1_IO09		0x1b0b0 /* Q7[112] LVDS_BLEN */
+		>;
+	};
 
-		pinctrl_q7_gpio0: q7-gpio0 {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_A25__GPIO5_IO02		0x1b0b0 /* Q7[185] GPIO0 */
-			>;
-		};
+	pinctrl_q7_gpio0: q7-gpio0grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A25__GPIO5_IO02		0x1b0b0 /* Q7[185] GPIO0 */
+		>;
+	};
 
-		pinctrl_q7_gpio1: q7-gpio1 {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_8__GPIO1_IO08		0x1b0b0 /* Q7[186] GPIO1 */
-			>;
-		};
+	pinctrl_q7_gpio1: q7-gpio1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_8__GPIO1_IO08		0x1b0b0 /* Q7[186] GPIO1 */
+		>;
+	};
 
-		pinctrl_q7_gpio2: q7-gpio2 {
-			fsl,pins = <
-				MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26	0x1b0b0 /* Q7[187] GPIO2 */
-			>;
-		};
+	pinctrl_q7_gpio2: q7-gpio2grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26	0x1b0b0 /* Q7[187] GPIO2 */
+		>;
+	};
 
-		pinctrl_q7_gpio3: q7-gpio3 {
-			fsl,pins = <
-				MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27	0x1b0b0 /* Q7[188] GPIO3 */
-			>;
-		};
+	pinctrl_q7_gpio3: q7-gpio3grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27	0x1b0b0 /* Q7[188] GPIO3 */
+		>;
+	};
 
-		pinctrl_q7_gpio4: q7-gpio4 {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_0__GPIO1_IO00		0x1b0b0 /* Q7[189] GPIO4 */
-			>;
-		};
+	pinctrl_q7_gpio4: q7-gpio4grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_0__GPIO1_IO00		0x1b0b0 /* Q7[189] GPIO4 */
+		>;
+	};
 
-		pinctrl_q7_gpio5: q7-gpio5 {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b0 /* Q7[190] GPIO5 */
-			>;
-		};
+	pinctrl_q7_gpio5: q7-gpio5grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b0 /* Q7[190] GPIO5 */
+		>;
+	};
 
-		pinctrl_q7_gpio6: q7-gpio6 {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_16__GPIO7_IO11		0x1b0b0 /* Q7[191] GPIO6 */
-			>;
-		};
+	pinctrl_q7_gpio6: q7-gpio6grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_16__GPIO7_IO11		0x1b0b0 /* Q7[191] GPIO6 */
+		>;
+	};
 
-		pinctrl_q7_gpio7: q7-gpio7 {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL4__GPIO4_IO14		0x1b0b0 /* Q7[192] GPIO7 */
-			>;
-		};
+	pinctrl_q7_gpio7: q7-gpio7grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL4__GPIO4_IO14		0x1b0b0 /* Q7[192] GPIO7 */
+		>;
+	};
 
-		pinctrl_q7_hda_reset: q7-hda-reset {
-			fsl,pins = <
-				MX6QDL_PAD_NANDF_ALE__GPIO6_IO08	0x1b0b0 /* Q7[61] HDA_RST_N */
-			>;
-		};
+	pinctrl_q7_hda_reset: q7-hda-resetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_ALE__GPIO6_IO08	0x1b0b0 /* Q7[61] HDA_RST_N */
+		>;
+	};
 
-		pinctrl_q7_lcd_power: lcd-power {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_7__GPIO1_IO07		0x1b0b0 /* Q7[111] LVDS_PPEN */
-			>;
-		};
+	pinctrl_q7_lcd_power: lcd-powergrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_7__GPIO1_IO07		0x1b0b0 /* Q7[111] LVDS_PPEN */
+		>;
+	};
 
-		pinctrl_q7_sdio_power: q7-sdio-power {
-			fsl,pins = <
-				MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30	0x1b0b0 /* Q7[47] SDIO_PWR# */
-			>;
-		};
+	pinctrl_q7_sdio_power: q7-sdio-powergrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30	0x1b0b0 /* Q7[47] SDIO_PWR# */
+		>;
+	};
 
-		pinctrl_q7_sleep_button: q7-sleep-button {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_ROW0__GPIO4_IO07		0x1b0b0 /* Q7[21] SLP_BTN# */
-			>;
-		};
+	pinctrl_q7_sleep_button: q7-sleep-buttongrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW0__GPIO4_IO07		0x1b0b0 /* Q7[21] SLP_BTN# */
+		>;
+	};
 
-		pinctrl_q7_spi_cs1: spi-cs1 {
-			fsl,pins = <
-				MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25	0x1b0b0 /* Q7[202] SPI_CS1# */
-			>;
-		};
+	pinctrl_q7_spi_cs1: spi-cs1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25	0x1b0b0 /* Q7[202] SPI_CS1# */
+		>;
+	};
 
-		/* SPI1 bus does not leave System on Module */
-		pinctrl_spi1: spi1 {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
-				MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
-				MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
-				MX6QDL_PAD_EIM_D19__GPIO3_IO19		0x1b0b0
-			>;
-		};
+	/* SPI1 bus does not leave System on Module */
+	pinctrl_spi1: spi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19		0x1b0b0
+		>;
+	};
 
-		/* Debug connector on Q7 module */
-		pinctrl_uart2: uart2 {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D26__UART2_TX_DATA	0x1b0b1
-				MX6QDL_PAD_EIM_D27__UART2_RX_DATA	0x1b0b1
-			>;
-		};
+	/* Debug connector on Q7 module */
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D26__UART2_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D27__UART2_RX_DATA	0x1b0b1
+		>;
+	};
 
-		pinctrl_uart3: uart3 {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1 /* Q7[177] UART0_RX */
-				MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1 /* Q7[171] UART0_TX */
-			>;
-		};
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1 /* Q7[177] UART0_RX */
+			MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1 /* Q7[171] UART0_TX */
+		>;
+	};
 
-		pinctrl_usbotg: usbotg {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059 /* Q7[92] USB_ID */
-			>;
-		};
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059 /* Q7[92] USB_ID */
+		>;
+	};
 
-		/* µSD card slot on Q7 module */
-		pinctrl_usdhc2: usdhc2 {
-			fsl,pins = <
-				MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
-				MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
-				MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
-				MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
-				MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
-				MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
-				MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1b0b0 /* SD2_CD */
-			>;
-		};
+	/* µSD card slot on Q7 module */
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1b0b0 /* SD2_CD */
+		>;
+	};
 
-		/* eMMC module on Q7 module */
-		pinctrl_usdhc3: usdhc3 {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
-				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
-				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
-				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
-				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
-				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
-				MX6QDL_PAD_SD3_DAT4__SD3_DATA4		0x17059
-				MX6QDL_PAD_SD3_DAT5__SD3_DATA5		0x17059
-				MX6QDL_PAD_SD3_DAT6__SD3_DATA6		0x17059
-				MX6QDL_PAD_SD3_DAT7__SD3_DATA7		0x17059
-			>;
-		};
+	/* eMMC module on Q7 module */
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4		0x17059
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5		0x17059
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6		0x17059
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7		0x17059
+		>;
+	};
 
-		pinctrl_usdhc4: usdhc4 {
-			fsl,pins = <
-				MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059 /* Q7[45] SDIO_CMD */
-				MX6QDL_PAD_SD4_CLK__SD4_CLK		0x17059 /* Q7[42] SDIO_CLK */
-				MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059 /* Q7[48] SDIO_DAT1 */
-				MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059 /* Q7[49] SDIO_DAT0 */
-				MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059 /* Q7[50] SDIO_DAT3 */
-				MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059 /* Q7[51] SDIO_DAT2 */
-			>;
-		};
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059 /* Q7[45] SDIO_CMD */
+			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x17059 /* Q7[42] SDIO_CLK */
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059 /* Q7[48] SDIO_DAT1 */
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059 /* Q7[49] SDIO_DAT0 */
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059 /* Q7[50] SDIO_DAT3 */
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059 /* Q7[51] SDIO_DAT2 */
+		>;
+	};
 
-		pinctrl_wdog: wdog {
-			fsl,pins = <
-				MX6QDL_PAD_DISP0_DAT8__WDOG1_B		0x1b0b0 /* Watchdog output signal */
-			>;
-		};
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT8__WDOG1_B		0x1b0b0 /* Watchdog output signal */
+		>;
 	};
 };
diff --git a/arch/arm/boot/dts/imx6dl-rex-basic.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-rex-basic.dts
index 0f1616bfa9a8..b72f8ea1e6f6 100644
--- a/arch/arm/boot/dts/imx6dl-rex-basic.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-rex-basic.dts
@@ -19,7 +19,7 @@
 };
 
 &ecspi3 {
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "sst,sst25vf016b", "jedec,spi-nor";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/imx6dl-riotboard.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-riotboard.dts
index e7d9bfbfd0e4..55b7e91d2ac0 100644
--- a/arch/arm/boot/dts/imx6dl-riotboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-riotboard.dts
@@ -25,14 +25,14 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_led>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 
-		led1: user2 {
+		led1: led-user2 {
 			label = "user2";
 			gpios = <&gpio3 28 GPIO_ACTIVE_LOW>;
 			default-state = "off";
@@ -90,6 +90,7 @@
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii-id";
 	phy-handle = <&rgmii_phy>;
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
@@ -171,12 +172,13 @@
 	codec: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_3p3v>;
 	};
 
-	pmic: pf0100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
 		reg = <0x08>;
 		interrupt-parent = <&gpio5>;
@@ -387,210 +389,206 @@
 };
 
 &iomuxc {
-	pinctrl-names = "default";
-
-	imx6-riotboard {
-		pinctrl_audmux: audmuxgrp {
-			fsl,pins = <
-				MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
-				MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
-				MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
-				MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
-				MX6QDL_PAD_GPIO_0__CCM_CLKO1		0x130b0		/* CAM_MCLK */
-			>;
-		};
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
+			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
+			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
+			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
+			MX6QDL_PAD_GPIO_0__CCM_CLKO1		0x130b0		/* CAM_MCLK */
+		>;
+	};
 
-		pinctrl_ecspi1: ecspi1grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
-				MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
-				MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
-				MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17	0x000b1		/* CS0 */
-			>;
-		};
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
+			MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17	0x000b1		/* CS0 */
+		>;
+	};
 
-		pinctrl_ecspi2: ecspi2grp {
-			fsl,pins = <
-				MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09	0x000b1		/* CS1 */
-				MX6QDL_PAD_DISP0_DAT16__ECSPI2_MOSI	0x100b1
-				MX6QDL_PAD_DISP0_DAT17__ECSPI2_MISO	0x100b1
-				MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12	0x000b1		/* CS0 */
-				MX6QDL_PAD_DISP0_DAT19__ECSPI2_SCLK	0x100b1
-			>;
-		};
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09	0x000b1		/* CS1 */
+			MX6QDL_PAD_DISP0_DAT16__ECSPI2_MOSI	0x100b1
+			MX6QDL_PAD_DISP0_DAT17__ECSPI2_MISO	0x100b1
+			MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12	0x000b1		/* CS0 */
+			MX6QDL_PAD_DISP0_DAT19__ECSPI2_SCLK	0x100b1
+		>;
+	};
 
-		pinctrl_ecspi3: ecspi3grp {
-			fsl,pins = <
-				MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK	0x100b1
-				MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI	0x100b1
-				MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO	0x100b1
-				MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24	0x000b1		/* CS0 */
-				MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25	0x000b1		/* CS1 */
-			>;
-		};
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK	0x100b1
+			MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI	0x100b1
+			MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO	0x100b1
+			MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24	0x000b1		/* CS0 */
+			MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25	0x000b1		/* CS1 */
+		>;
+	};
 
-		pinctrl_enet: enetgrp {
-			fsl,pins = <
-				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
-				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
-				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
-				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
-				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
-				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
-				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
-				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
-				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x0a0b1		/* AR8035 CLK_25M --> ENET_REF_CLK (V22) */
-				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030		/* AR8035 pin strapping: IO voltage: pull up */
-				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x13030		/* AR8035 pin strapping: PHYADDR#0: pull down */
-				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x13030		/* AR8035 pin strapping: PHYADDR#1: pull down */
-				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030		/* AR8035 pin strapping: MODE#1: pull up */
-				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030		/* AR8035 pin strapping: MODE#3: pull up */
-				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x130b0		/* AR8035 pin strapping: MODE#0: pull down */
-				MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8	/* GPIO16 -> AR8035 25MHz */
-				MX6QDL_PAD_EIM_D31__GPIO3_IO31		0x130b0		/* RGMII_nRST */
-				MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28	0x180b0		/* AR8035 interrupt */
-				MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
-			>;
-		};
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x0a0b1		/* AR8035 CLK_25M --> ENET_REF_CLK (V22) */
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030		/* AR8035 pin strapping: IO voltage: pull up */
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x13030		/* AR8035 pin strapping: PHYADDR#0: pull down */
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x13030		/* AR8035 pin strapping: PHYADDR#1: pull down */
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030		/* AR8035 pin strapping: MODE#1: pull up */
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030		/* AR8035 pin strapping: MODE#3: pull up */
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x130b0		/* AR8035 pin strapping: MODE#0: pull down */
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8	/* GPIO16 -> AR8035 25MHz */
+			MX6QDL_PAD_EIM_D31__GPIO3_IO31		0x130b0		/* RGMII_nRST */
+			MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28	0x180b0		/* AR8035 interrupt */
+			MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
+		>;
+	};
 
-		pinctrl_i2c1: i2c1grp {
-			fsl,pins = <
-				MX6QDL_PAD_CSI0_DAT8__I2C1_SDA		0x4001b8b1
-				MX6QDL_PAD_CSI0_DAT9__I2C1_SCL		0x4001b8b1
-			>;
-		};
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA		0x4001b8b1
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL		0x4001b8b1
+		>;
+	};
 
-		pinctrl_i2c2: i2c2grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
-				MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
-			>;
-		};
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
+		>;
+	};
 
-		pinctrl_i2c3: i2c3grp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_5__I2C3_SCL		0x4001b8b1
-				MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
-			>;
-		};
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL		0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
+		>;
+	};
 
-		pinctrl_i2c4: i2c4grp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_7__I2C4_SCL             0x4001b8b1
-				MX6QDL_PAD_GPIO_8__I2C4_SDA             0x4001b8b1
-			>;
-		};
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_7__I2C4_SCL             0x4001b8b1
+			MX6QDL_PAD_GPIO_8__I2C4_SDA             0x4001b8b1
+		>;
+	};
 
-		pinctrl_led: ledgrp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_A25__GPIO5_IO02		0x1b0b1	/* user led0 */
-				MX6QDL_PAD_EIM_D28__GPIO3_IO28		0x1b0b1	/* user led1 */
-			>;
-		};
+	pinctrl_led: ledgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A25__GPIO5_IO02		0x1b0b1	/* user led0 */
+			MX6QDL_PAD_EIM_D28__GPIO3_IO28		0x1b0b1	/* user led1 */
+		>;
+	};
 
-		pinctrl_pwm1: pwm1grp {
-			fsl,pins = <
-				MX6QDL_PAD_DISP0_DAT8__PWM1_OUT		0x1b0b1
-			>;
-		};
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT8__PWM1_OUT		0x1b0b1
+		>;
+	};
 
-		pinctrl_pwm2: pwm2grp {
-			fsl,pins = <
-				MX6QDL_PAD_DISP0_DAT9__PWM2_OUT		0x1b0b1
-			>;
-		};
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT9__PWM2_OUT		0x1b0b1
+		>;
+	};
 
-		pinctrl_pwm3: pwm3grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_DAT1__PWM3_OUT		0x1b0b1
-			>;
-		};
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT1__PWM3_OUT		0x1b0b1
+		>;
+	};
 
-		pinctrl_pwm4: pwm4grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_CMD__PWM4_OUT		0x1b0b1
-			>;
-		};
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__PWM4_OUT		0x1b0b1
+		>;
+	};
 
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0b1
-				MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0b1
-			>;
-		};
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0b1
+		>;
+	};
 
-		pinctrl_uart2: uart2grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D26__UART2_TX_DATA	0x1b0b1
-				MX6QDL_PAD_EIM_D27__UART2_RX_DATA	0x1b0b1
-			>;
-		};
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D26__UART2_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D27__UART2_RX_DATA	0x1b0b1
+		>;
+	};
 
-		pinctrl_uart3: uart3grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
-				MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
-			>;
-		};
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
+		>;
+	};
 
-		pinctrl_uart4: uart4grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL0__UART4_TX_DATA	0x1b0b1
-				MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA	0x1b0b1
-			>;
-		};
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA	0x1b0b1
+			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA	0x1b0b1
+		>;
+	};
 
-		pinctrl_uart5: uart5grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL1__UART5_TX_DATA	0x1b0b1
-				MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA	0x1b0b1
-			>;
-		};
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL1__UART5_TX_DATA	0x1b0b1
+			MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA	0x1b0b1
+		>;
+	};
 
-		pinctrl_usbotg: usbotggrp {
-			fsl,pins = <
-				MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x17059
-				MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x000b0	/* MX6QDL_PAD_EIM_D22__USB_OTG_PWR */
-				MX6QDL_PAD_EIM_D21__USB_OTG_OC		0x1b0b0
-			>;
-		};
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x17059
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x000b0	/* MX6QDL_PAD_EIM_D22__USB_OTG_PWR */
+			MX6QDL_PAD_EIM_D21__USB_OTG_OC		0x1b0b0
+		>;
+	};
 
-		pinctrl_usdhc2: usdhc2grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
-				MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
-				MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
-				MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
-				MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
-				MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
-				MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1b0b0	/* SD2 CD */
-				MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1f0b0	/* SD2 WP */
-			>;
-		};
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1b0b0	/* SD2 CD */
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1f0b0	/* SD2 WP */
+		>;
+	};
 
-		pinctrl_usdhc3: usdhc3grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
-				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
-				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
-				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
-				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
-				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
-				MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x1b0b0	/* SD3 CD */
-				MX6QDL_PAD_SD3_DAT4__GPIO7_IO01		0x1f0b0	/* SD3 WP */
-			>;
-		};
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+			MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x1b0b0	/* SD3 CD */
+			MX6QDL_PAD_SD3_DAT4__GPIO7_IO01		0x1f0b0	/* SD3 WP */
+		>;
+	};
 
-		pinctrl_usdhc4: usdhc4grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
-				MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
-				MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
-				MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
-				MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
-				MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059
-				MX6QDL_PAD_NANDF_ALE__GPIO6_IO08	0x17059	/* SD4 RST (eMMC) */
-			>;
-		};
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
+			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059
+			MX6QDL_PAD_NANDF_ALE__GPIO6_IO08	0x17059	/* SD4 RST (eMMC) */
+		>;
 	};
 };
diff --git a/arch/arm/boot/dts/imx6dl-sabreauto.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-sabreauto.dts
index ff3283c83a39..ff3283c83a39 100644
--- a/arch/arm/boot/dts/imx6dl-sabreauto.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-sabreauto.dts
diff --git a/arch/arm/boot/dts/imx6dl-sabrelite.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-sabrelite.dts
index 33040761b253..33040761b253 100644
--- a/arch/arm/boot/dts/imx6dl-sabrelite.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-sabrelite.dts
diff --git a/arch/arm/boot/dts/imx6dl-sabresd.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-sabresd.dts
index cd6bbf22a16f..cd6bbf22a16f 100644
--- a/arch/arm/boot/dts/imx6dl-sabresd.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-sabresd.dts
diff --git a/arch/arm/boot/dts/imx6dl-savageboard.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-savageboard.dts
index b95469c520a4..b95469c520a4 100644
--- a/arch/arm/boot/dts/imx6dl-savageboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-savageboard.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-sielaff.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-sielaff.dts
new file mode 100644
index 000000000000..7de8d5f26518
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-sielaff.dts
@@ -0,0 +1,533 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright (C) 2022 Kontron Electronics GmbH
+ */
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include <dt-bindings/clock/imx6qdl-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Sielaff i.MX6 Solo";
+	compatible = "sielaff,imx6dl-board", "fsl,imx6dl";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	backlight: pwm-backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight>;
+		pwms = <&pwm3 0 50000 0>;
+		brightness-levels = <0 0 64 88 112 136 184 232 255>;
+		default-brightness-level = <4>;
+		enable-gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>;
+		power-supply = <&reg_backlight>;
+	};
+
+	cec {
+		compatible = "cec-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_hdmi_cec>;
+		cec-gpios = <&gpio2 7 GPIO_ACTIVE_HIGH>;
+		hdmi-phandle = <&hdmi>;
+	};
+
+	enet_ref: clock-enet-ref {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+		clock-output-names = "enet-ref";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		key-0 {
+			gpios = <&gpio2 16 0>;
+			debounce-interval = <10>;
+			linux,code = <1>;
+		};
+
+		key-1 {
+			gpios = <&gpio3 27 0>;
+			debounce-interval = <10>;
+			linux,code = <2>;
+		};
+
+		key-2 {
+			gpios = <&gpio5 4 0>;
+			debounce-interval = <10>;
+			linux,code = <3>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+
+		led-debug {
+			label = "debug-led";
+			gpios = <&gpio5 21 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x20000000>;
+		device_type = "memory";
+	};
+
+	osc_eth_phy: clock-osc-eth-phy {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+		clock-output-names = "osc-eth-phy";
+	};
+
+	panel {
+		compatible = "lg,lb070wv8";
+		backlight = <&backlight>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in_lvds: endpoint {
+				remote-endpoint = <&lvds_out>;
+			};
+		};
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_backlight: regulator-backlight {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_backlight>;
+		enable-active-high;
+		gpio = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+		regulator-name = "backlight";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usbotg_vbus>;
+		enable-active-high;
+		gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+};
+
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	cs-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&fec {
+	/*
+	 * Set PTP clock to external instead of internal reference, as the
+	 * REF_CLK from the PHY is fed back into the i.MX6 and the GPR
+	 * register needs to be set accordingly (see mach-imx6q.c).
+	 */
+	clocks = <&clks IMX6QDL_CLK_ENET>,
+		 <&clks IMX6QDL_CLK_ENET>,
+		 <&enet_ref>,
+		 <&clks IMX6QDL_CLK_ENET_REF>;
+	clock-names = "ipg", "ahb", "ptp", "enet_out";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-connection-type = "rmii";
+	phy-handle = <&ethphy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@1 {
+			reg = <1>;
+			clocks = <&osc_eth_phy>;
+			clock-names = "rmii-ref";
+			micrel,led-mode = <1>;
+			reset-assert-us = <500>;
+			reset-deassert-us = <100>;
+			reset-gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "key-out", "key-in",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"lan9500a-rst", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	status = "okay";
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c4>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	touchscreen@55 {
+		compatible = "sitronix,st1633";
+		reg = <0x55>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touch>;
+		interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-parent = <&gpio5>;
+		gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+		status = "disabled";
+	};
+
+	touchscreen@5d {
+		compatible = "goodix,gt928";
+		reg = <0x5d>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touch>;
+		interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio5>;
+		irq-gpios = <&gpio5 18 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+};
+
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&ldb {
+	status = "okay";
+
+	lvds: lvds-channel@0 {
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <24>;
+		status = "okay";
+
+		port@4 {
+			reg = <4>;
+
+			lvds_out: endpoint {
+				remote-endpoint = <&panel_in_lvds>;
+			};
+		};
+	};
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&usbh1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbh1>;
+	disable-over-current;
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	usb1@1 {
+		compatible = "usb4b4,6570";
+		reg = <1>;
+		clocks = <&clks IMX6QDL_CLK_CKO>;
+
+		assigned-clocks = <&clks IMX6QDL_CLK_CKO>,
+				  <&clks IMX6QDL_CLK_CKO2_SEL>;
+		assigned-clock-parents = <&clks IMX6QDL_CLK_CKO2>,
+					 <&clks IMX6QDL_CLK_OSC>;
+		assigned-clock-rates = <12000000 0>;
+	};
+};
+
+&usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	dr_mode = "host";
+	over-current-active-low;
+	vbus-supply = <&reg_usb_otg_vbus>;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&reg_3v3>;
+	voltage-ranges = <3300 3300>;
+	no-1-8-v;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_RD0__GPIO6_IO25	0x1b0b0	/* PMIC_IRQ */
+			MX6QDL_PAD_SD2_DAT3__GPIO1_IO12		0x1b0b0
+			MX6QDL_PAD_SD2_DAT1__GPIO1_IO14		0x1b0b0
+			MX6QDL_PAD_SD2_DAT0__GPIO1_IO15		0x1b0b0
+			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08		0x1b0b0
+			MX6QDL_PAD_EIM_D29__GPIO3_IO29		0x1b0b0
+		>;
+	};
+
+	pinctrl_backlight: backlightgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CS3__GPIO6_IO16	0x100b1
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__ECSPI2_MISO	0x100b1
+			MX6QDL_PAD_CSI0_DAT9__ECSPI2_MOSI	0x100b1
+			MX6QDL_PAD_CSI0_DAT8__ECSPI2_SCLK	0x100b1
+			MX6QDL_PAD_CSI0_DAT11__GPIO5_IO29	0x100b1
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0	0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1	0x1b0b0
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN	0x1b0b0
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER	0x1b0b0
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0	0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1	0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN	0x1b0b0
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
+			MX6QDL_PAD_EIM_A25__GPIO5_IO02		0x100b1
+		>;
+	};
+
+	pinctrl_gpio_keys: gpiokeysgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A22__GPIO2_IO16		0x1b080
+			MX6QDL_PAD_EIM_D27__GPIO3_IO27		0x1b080
+			MX6QDL_PAD_EIM_A24__GPIO5_IO04		0x1b080
+		>;
+	};
+
+	pinctrl_gpio_leds: gpioledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21	0x1b0b0
+		>;
+	};
+
+	pinctrl_gpmi_nand: gpminandgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CLE__NAND_CLE		0xb0b1
+			MX6QDL_PAD_NANDF_ALE__NAND_ALE		0xb0b1
+			MX6QDL_PAD_NANDF_WP_B__NAND_WP_B	0xb0b1
+			MX6QDL_PAD_NANDF_RB0__NAND_READY_B	0xb000
+			MX6QDL_PAD_NANDF_CS0__NAND_CE0_B	0xb0b1
+			MX6QDL_PAD_SD4_CMD__NAND_RE_B		0xb0b1
+			MX6QDL_PAD_SD4_CLK__NAND_WE_B		0xb0b1
+			MX6QDL_PAD_NANDF_D0__NAND_DATA00	0xb0b1
+			MX6QDL_PAD_NANDF_D1__NAND_DATA01	0xb0b1
+			MX6QDL_PAD_NANDF_D2__NAND_DATA02	0xb0b1
+			MX6QDL_PAD_NANDF_D3__NAND_DATA03	0xb0b1
+			MX6QDL_PAD_NANDF_D4__NAND_DATA04	0xb0b1
+			MX6QDL_PAD_NANDF_D5__NAND_DATA05	0xb0b1
+			MX6QDL_PAD_NANDF_D6__NAND_DATA06	0xb0b1
+			MX6QDL_PAD_NANDF_D7__NAND_DATA07	0xb0b1
+		>;
+	};
+
+	pinctrl_hdmi_cec: hdmicecgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A21__GPIO2_IO17		0x1b8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL		0x4001f8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_7__I2C4_SCL		0x4001b8b1
+			MX6QDL_PAD_GPIO_8__I2C4_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
+		>;
+	};
+
+	pinctrl_reg_backlight: regbacklightgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_REF_CLK__GPIO1_IO23	0x1b0b1
+		>;
+	};
+
+	pinctrl_reg_usbotg_vbus: regusbotgvbusgrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b1
+		>;
+	};
+
+	pinctrl_touch: touchgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1b0b0
+			MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18	0x1b0b0
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 	0x1b0b1
+			MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA	0x1b0b1
+			MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b0
+			MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b0
+		>;
+	};
+
+	pinctrl_usbh1: usbh1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_3__USB_H1_OC		0x1b0b1
+			MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1		0x1b0b0
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL4__USB_OTG_OC		0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x100b1
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__WDOG1_B		0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6dl-skov-revc-lt2.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-skov-revc-lt2.dts
index b12b5aabe70a..b12b5aabe70a 100644
--- a/arch/arm/boot/dts/imx6dl-skov-revc-lt2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-skov-revc-lt2.dts
diff --git a/arch/arm/boot/dts/imx6dl-skov-revc-lt6.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-skov-revc-lt6.dts
index 5dcc433fe2af..5dcc433fe2af 100644
--- a/arch/arm/boot/dts/imx6dl-skov-revc-lt6.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-skov-revc-lt6.dts
diff --git a/arch/arm/boot/dts/imx6dl-solidsense.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-solidsense.dts
index 2a3699adbed0..2a3699adbed0 100644
--- a/arch/arm/boot/dts/imx6dl-solidsense.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-solidsense.dts
diff --git a/arch/arm/boot/dts/imx6dl-tqma6a.dtsi b/arch/arm/boot/dts/nxp/imx/imx6dl-tqma6a.dtsi
index e891ef9b0091..e891ef9b0091 100644
--- a/arch/arm/boot/dts/imx6dl-tqma6a.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-tqma6a.dtsi
diff --git a/arch/arm/boot/dts/imx6dl-tqma6b.dtsi b/arch/arm/boot/dts/nxp/imx/imx6dl-tqma6b.dtsi
index 38cd8501a886..38cd8501a886 100644
--- a/arch/arm/boot/dts/imx6dl-tqma6b.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-tqma6b.dtsi
diff --git a/arch/arm/boot/dts/imx6dl-ts4900.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-ts4900.dts
index 3d60cc725d9e..3d60cc725d9e 100644
--- a/arch/arm/boot/dts/imx6dl-ts4900.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-ts4900.dts
diff --git a/arch/arm/boot/dts/imx6dl-ts7970.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-ts7970.dts
index 5da6feba2e66..5da6feba2e66 100644
--- a/arch/arm/boot/dts/imx6dl-ts7970.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-ts7970.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-tx6dl-comtft.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6dl-comtft.dts
new file mode 100644
index 000000000000..136ae7841878
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6dl-comtft.dts
@@ -0,0 +1,42 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2014-2017 Lothar Waßmann <LW@KARO-electronics.de>
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-tx6.dtsi"
+#include "imx6qdl-tx6-lcd.dtsi"
+
+/ {
+	model = "Ka-Ro electronics TX6DL Module on CoMpact TFT";
+	compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
+};
+
+&backlight {
+	pwms = <&pwm2 0 500000 0>;
+};
+
+&can1 {
+	status = "disabled";
+};
+
+&can2 {
+	xceiver-supply = <&reg_3v3>;
+};
+
+&kpp {
+	status = "disabled";
+};
+
+&lcd_panel {
+	compatible = "edt,etm0700g0edh6";
+};
+
+&reg_can_xcvr {
+	status = "disabled";
+};
+
+&touchscreen {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-tx6s-8034-mb7.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6s-8034-mb7.dts
new file mode 100644
index 000000000000..e1b525ed292a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6s-8034-mb7.dts
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
+ */
+
+/dts-v1/;
+#include "imx6dl-tx6s-8034.dts"
+#include "imx6qdl-tx6-mb7.dtsi"
+
+/ {
+	model = "Ka-Ro electronics TX6S-8034 Module on MB7 baseboard";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-tx6s-8034.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6s-8034.dts
new file mode 100644
index 000000000000..9a6a5cda9a3b
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6s-8034.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2015-2017 Lothar Waßmann <LW@KARO-electronics.de>
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-tx6.dtsi"
+#include "imx6qdl-tx6-lcd.dtsi"
+
+/ {
+	model = "Ka-Ro electronics TX6S-8034 Module";
+	compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
+
+	cpus {
+		/delete-node/ cpu@1;
+	};
+};
+
+&ds1339 {
+	status = "disabled";
+};
+
+&pinctrl_usdhc1 {
+	fsl,pins = <
+		MX6QDL_PAD_SD1_CMD__SD1_CMD		0x070b1
+		MX6QDL_PAD_SD1_CLK__SD1_CLK		0x070b1
+		MX6QDL_PAD_SD1_DAT0__SD1_DATA0		0x070b1
+		MX6QDL_PAD_SD1_DAT1__SD1_DATA1		0x070b1
+		MX6QDL_PAD_SD1_DAT2__SD1_DATA2		0x070b1
+		MX6QDL_PAD_SD1_DAT3__SD1_DATA3		0x070b1
+		MX6QDL_PAD_SD3_CMD__GPIO7_IO02		0x170b0 /* SD1 CD */
+	>;
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-tx6s-8035-mb7.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6s-8035-mb7.dts
new file mode 100644
index 000000000000..0e8f4c3f3760
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6s-8035-mb7.dts
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
+ */
+
+/dts-v1/;
+#include "imx6dl-tx6s-8035.dts"
+#include "imx6qdl-tx6-mb7.dtsi"
+
+/ {
+	model = "Ka-Ro electronics TX6U-8035 Module on MB7 baseboard";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-tx6s-8035.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6s-8035.dts
new file mode 100644
index 000000000000..9958e8701c98
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6s-8035.dts
@@ -0,0 +1,50 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2015-2017 Lothar Waßmann <LW@KARO-electronics.de>
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-tx6.dtsi"
+#include "imx6qdl-tx6-lcd.dtsi"
+
+/ {
+	model = "Ka-Ro electronics TX6S-8035 Module";
+	compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
+
+	cpus {
+		/delete-node/ cpu@1;
+	};
+};
+
+&ds1339 {
+	status = "disabled";
+};
+
+&gpmi {
+	status = "disabled";
+};
+
+&usdhc4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	bus-width = <4>;
+	non-removable;
+	no-1-8-v;
+	fsl,wp-controller;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x070b1
+			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x070b1
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x070b1
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x070b1
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x070b1
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x070b1
+			MX6QDL_PAD_NANDF_ALE__SD4_RESET		0x0b0b1
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-801x.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-801x.dts
new file mode 100644
index 000000000000..d9bfd340efb2
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-801x.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2014-2017 Lothar Waßmann <LW@KARO-electronics.de>
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-tx6.dtsi"
+#include "imx6qdl-tx6-lcd.dtsi"
+
+/ {
+	model = "Ka-Ro electronics TX6U-801x Module";
+	compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-8033-mb7.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-8033-mb7.dts
new file mode 100644
index 000000000000..8243f0d6d387
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-8033-mb7.dts
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
+ */
+
+/dts-v1/;
+#include "imx6dl-tx6u-8033.dts"
+#include "imx6qdl-tx6-mb7.dtsi"
+
+/ {
+	model = "Ka-Ro electronics TX6U-8033 Module on MB7 baseboard";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-8033.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-8033.dts
new file mode 100644
index 000000000000..2d031403ab19
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-8033.dts
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2014-2017 Lothar Waßmann <LW@KARO-electronics.de>
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-tx6.dtsi"
+#include "imx6qdl-tx6-lcd.dtsi"
+
+/ {
+	model = "Ka-Ro electronics TX6U-8033 Module";
+	compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
+};
+
+&ds1339 {
+	status = "disabled";
+};
+
+&gpmi {
+	status = "disabled";
+};
+
+&usdhc4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	bus-width = <4>;
+	non-removable;
+	no-1-8-v;
+	fsl,wp-controller;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x070b1
+			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x070b1
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x070b1
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x070b1
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x070b1
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x070b1
+			MX6QDL_PAD_NANDF_ALE__SD4_RESET		0x0b0b1
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-80xx-mb7.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-80xx-mb7.dts
new file mode 100644
index 000000000000..684a2583db75
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-80xx-mb7.dts
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
+ */
+
+/dts-v1/;
+#include "imx6dl-tx6u-801x.dts"
+#include "imx6qdl-tx6-mb7.dtsi"
+
+/ {
+	model = "Ka-Ro electronics TX6U-8030/-8010/-8012 Module on MB7 baseboard";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-811x.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-811x.dts
new file mode 100644
index 000000000000..7fdc794615f2
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-811x.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2014-2017 Lothar Waßmann <LW@KARO-electronics.de>
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-tx6.dtsi"
+#include "imx6qdl-tx6-lvds.dtsi"
+
+/ {
+	model = "Ka-Ro electronics TX6U-811x Module";
+	compatible = "karo,imx6dl-tx6dl", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-81xx-mb7.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-81xx-mb7.dts
new file mode 100644
index 000000000000..209aaebe148a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-tx6u-81xx-mb7.dts
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2016-2017 Lothar Waßmann <LW@KARO-electronics.de>
+ */
+
+/dts-v1/;
+#include "imx6dl-tx6u-811x.dts"
+#include "imx6qdl-tx6-mb7.dtsi"
+
+/ {
+	model = "Ka-Ro electronics TX6U-8130/-8110 Module on MB7 baseboard";
+};
diff --git a/arch/arm/boot/dts/imx6dl-udoo.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-udoo.dts
index d871cac1711f..d871cac1711f 100644
--- a/arch/arm/boot/dts/imx6dl-udoo.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-udoo.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-victgo.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-victgo.dts
new file mode 100644
index 000000000000..4875afadb630
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-victgo.dts
@@ -0,0 +1,360 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2016 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-vicut1.dtsi"
+
+/ {
+	model = "Kverneland TGO";
+	compatible = "kvg,victgo", "fsl,imx6dl";
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpiokeys>;
+		autorepeat;
+
+		key-power {
+			label = "Power Button";
+			gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+
+		key-enter {
+			label = "Rotary Key";
+			gpios = <&gpio2 05 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_ENTER>;
+			wakeup-source;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&vdiv_vaccu>, <&vdiv_hitch_pos>;
+	};
+
+	panel {
+		compatible = "lg,lb070wv8";
+		backlight = <&backlight_lcd>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+
+	clk50m_phy: phy-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+		clock-output-names = "enet_ref_pad";
+	};
+
+	rotary-encoder {
+		compatible = "rotary-encoder";
+		pinctrl-0 = <&pinctrl_rotary_ch>;
+		gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>,
+			<&gpio2 4 GPIO_ACTIVE_HIGH>;
+		linux,axis = <REL_WHEEL>;
+		rotary-encoder,steps-per-period = <4>;
+		rotary-encoder,relative-axis;
+		rotary-encoder,rollover;
+		wakeup-source;
+	};
+
+	thermal-zones {
+		chassis-thermal {
+			polling-delay = <20000>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&tsens0>;
+
+			trips {
+				alert {
+					temperature = <105000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+			};
+		};
+
+		touch-thermal0 {
+			polling-delay = <20000>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&touch_temp0>;
+
+			trips {
+				alert {
+					temperature = <105000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+			};
+		};
+
+		touch-thermal1 {
+			polling-delay = <20000>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&touch_temp1>;
+
+			trips {
+				alert {
+					temperature = <105000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+			};
+		};
+	};
+
+	touchscreen {
+		compatible = "resistive-adc-touch";
+		io-channels = <&adc_ts 1>, <&adc_ts 3>, <&adc_ts 4>,
+                              <&adc_ts 5>;
+		io-channel-names = "y", "z1", "z2", "x";
+		touchscreen-min-pressure = <64687>;
+		touchscreen-inverted-y;
+		touchscreen-x-plate-ohms = <300>;
+		touchscreen-y-plate-ohms = <800>;
+	};
+
+	touch_temp0: touch-temperature-sensor0 {
+		compatible = "generic-adc-thermal";
+		#thermal-sensor-cells = <0>;
+		io-channels = <&adc_ts 0>;
+		io-channel-names = "sensor-channel";
+		temperature-lookup-table = <    (-40000) 736
+						85000 474>;
+	};
+
+	touch_temp1: touch-temperature-sensor1 {
+		compatible = "generic-adc-thermal";
+		#thermal-sensor-cells = <0>;
+		io-channels = <&adc_ts 7>;
+		io-channel-names = "sensor-channel";
+		temperature-lookup-table = <    (-40000) 826
+						85000 609>;
+	};
+
+	vdiv_vaccu: voltage-divider-vaccu {
+		compatible = "voltage-divider";
+		io-channels = <&adc_ts 2>;
+		output-ohms = <2500>;
+		full-ohms = <64000>;
+		#io-channel-cells = <0>;
+	};
+
+	vdiv_hitch_pos: voltage-divider-hitch-pos {
+		compatible = "voltage-divider";
+		io-channels = <&adc_ts 6>;
+		output-ohms = <3300>;
+		full-ohms = <13300>;
+		#io-channel-cells = <0>;
+	};
+};
+
+&clks {
+	clocks = <&clk50m_phy>;
+	clock-names = "enet_ref_pad";
+	assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&clk50m_phy>;
+};
+
+&ecspi2 {
+	cs-gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	status = "okay";
+
+	adc_ts: adc@0 {
+		compatible = "ti,tsc2046e-adc";
+		reg = <0>;
+		pinctrl-0 = <&pinctrl_touchscreen>;
+		pinctrl-names = "default";
+		spi-max-frequency = <1000000>;
+		interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;
+		#io-channel-cells = <1>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@1 {
+			reg = <1>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@3 {
+			reg = <3>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@4 {
+			reg = <4>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@5 {
+			reg = <5>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rmii";
+	phy-handle = <&rmii_phy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Microchip KSZ8081RNA PHY */
+		rmii_phy: ethernet-phy@0 {
+			reg = <0>;
+			interrupts-extended = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
+			"CAM2_MIRROR", "", "", "SMBALERT",
+		"DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
+		"SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
+			"SD1_DATA3", "ETH_MDIO", "",
+		"", "", "", "", "", "", "", "ETH_MDC";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
+		"UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
+			"CAN2_SR", "CAN2_TX", "CAN2_RX",
+		"", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
+			"HITCH_IN_OUT",
+		"LIGHT_ON", "", "ETH_RESET", "CONTACT_IN", "BL_EN",
+			"BL_PWM", "ETH_INT", "ISB_LED";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"TSC_PENIRQ", "TSC_BUSY", "ECSPI2_MOSI", "ECSPI2_MISO",
+			"ECSPI2_SS0", "ECSPI2_SCLK", "", "",
+		"", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
+			"I2S_BITCLK", "I2S_DOUT",
+		"I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
+			"YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
+};
+
+&gpio6 {
+	gpio-line-names =
+		"ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
+			"ITU656_D6", "ITU656_D7", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+	keypad@70 {
+		compatible = "holtek,ht16k33";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_keypad>;
+		reg = <0x70>;
+		refresh-rate-hz = <20>;
+		debounce-delay-ms = <50>;
+		interrupts-extended = <&gpio4 5 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>;
+		keypad,num-rows = <12>;
+		keypad,num-columns = <3>;
+		linux,keymap = <
+			MATRIX_KEY(2, 0, KEY_F6)
+			MATRIX_KEY(3, 0, KEY_F8)
+			MATRIX_KEY(4, 0, KEY_F10)
+			MATRIX_KEY(5, 0, KEY_F4)
+			MATRIX_KEY(6, 0, KEY_F2)
+			MATRIX_KEY(2, 1, KEY_F5)
+			MATRIX_KEY(3, 1, KEY_F7)
+			MATRIX_KEY(4, 1, KEY_F9)
+			MATRIX_KEY(5, 1, KEY_F3)
+			MATRIX_KEY(6, 1, KEY_F1)
+		      >;
+	};
+};
+
+&iomuxc {
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT16__ECSPI2_MOSI		0x100b1
+			MX6QDL_PAD_DISP0_DAT17__ECSPI2_MISO		0x100b1
+			MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12		0x100b1
+			MX6QDL_PAD_DISP0_DAT19__ECSPI2_SCLK		0x100b1
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			/* MX6QDL_ENET_PINGRP4 */
+			MX6QDL_PAD_ENET_MDC__ENET_MDC			0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO			0x1b0b0
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER		0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN		0x1b0b0
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN		0x1b0b0
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK		0x1b0b0
+			/* Phy reset */
+			MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26		0x1b0b0
+			/* nINTRP */
+			MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30		0x1b0b0
+		>;
+	};
+
+	pinctrl_gpiokeys: gpiokeygrp {
+		fsl,pins = <
+			/* ROTARY_BTN */
+			MX6QDL_PAD_NANDF_D5__GPIO2_IO05			0x1b0b0
+			/* nON_SWITCH */
+			MX6QDL_PAD_EIM_CS0__GPIO2_IO23			0x1b0b0
+		>;
+	};
+
+	pinctrl_keypad: keypadgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_19__GPIO4_IO05			0x1b0b0
+		>;
+	};
+
+	pinctrl_rotary_ch: rotarychgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D3__GPIO2_IO03			0x1b0b0
+			MX6QDL_PAD_NANDF_D4__GPIO2_IO04			0x1b0b0
+		>;
+	};
+
+	pinctrl_touchscreen: touchscreengrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT14__GPIO5_IO08		0x1b0b0
+			MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09		0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6dl-vicut1.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-vicut1.dts
index 174fd913bf96..5035d303447d 100644
--- a/arch/arm/boot/dts/imx6dl-vicut1.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-vicut1.dts
@@ -6,6 +6,7 @@
 /dts-v1/;
 #include "imx6dl.dtsi"
 #include "imx6qdl-vicut1.dtsi"
+#include "imx6qdl-vicut1-12inch.dtsi"
 
 / {
 	model = "Kverneland UT1 Board";
diff --git a/arch/arm/boot/dts/imx6dl-wandboard-revb1.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-wandboard-revb1.dts
index c2946fbaa0dd..c2946fbaa0dd 100644
--- a/arch/arm/boot/dts/imx6dl-wandboard-revb1.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-wandboard-revb1.dts
diff --git a/arch/arm/boot/dts/imx6dl-wandboard-revd1.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-wandboard-revd1.dts
index 6d1d863c2e3a..6d1d863c2e3a 100644
--- a/arch/arm/boot/dts/imx6dl-wandboard-revd1.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-wandboard-revd1.dts
diff --git a/arch/arm/boot/dts/imx6dl-wandboard.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-wandboard.dts
index 4a08d5a99452..4a08d5a99452 100644
--- a/arch/arm/boot/dts/imx6dl-wandboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-wandboard.dts
diff --git a/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-common.dtsi
index 674af39c884a..8bc6376d0dc1 100644
--- a/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-common.dtsi
@@ -55,6 +55,7 @@
 	panel: panel {
 		compatible = "dataimage,scf0700c48ggu18";
 		power-supply = <&sw2_reg>;
+		backlight = <&backlight>;
 		status = "disabled";
 
 		port {
@@ -97,7 +98,6 @@
 		regulator-max-microvolt = <5000000>;
 		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
-		status = "okay";
 	};
 };
 
@@ -105,8 +105,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii-id";
-	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
-	phy-reset-duration = <20>;
 	phy-supply = <&sw2_reg>;
 	status = "okay";
 
@@ -119,17 +117,10 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		phy_port2: phy@1 {
-			reg = <1>;
-		};
-
-		phy_port3: phy@2 {
-			reg = <2>;
-		};
-
 		switch@10 {
 			compatible = "qca,qca8334";
-			reg = <10>;
+			reg = <0x10>;
+			reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
 
 			switch_ports: ports {
 				#address-cells = <1>;
@@ -150,15 +141,30 @@
 				eth2: port@2 {
 					reg = <2>;
 					label = "eth2";
+					phy-mode = "internal";
 					phy-handle = <&phy_port2>;
 				};
 
 				eth1: port@3 {
 					reg = <3>;
 					label = "eth1";
+					phy-mode = "internal";
 					phy-handle = <&phy_port3>;
 				};
 			};
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy_port2: ethernet-phy@1 {
+					reg = <1>;
+				};
+
+				phy_port3: ethernet-phy@2 {
+					reg = <2>;
+				};
+			};
 		};
 	};
 };
@@ -269,11 +275,11 @@
 		compatible = "ti,lp5562";
 		reg = <0x30>;
 		clock-mode = /bits/ 8 <1>;
-		status = "disabled";
 		#address-cells = <1>;
 		#size-cells = <0>;
+		status = "disabled";
 
-		chan@0 {
+		led@0 {
 			chan-name = "R";
 			led-cur = /bits/ 8 <0x20>;
 			max-cur = /bits/ 8 <0x60>;
@@ -281,7 +287,7 @@
 			color = <LED_COLOR_ID_RED>;
 		};
 
-		chan@1 {
+		led@1 {
 			chan-name = "G";
 			led-cur = /bits/ 8 <0x20>;
 			max-cur = /bits/ 8 <0x60>;
@@ -289,7 +295,7 @@
 			color = <LED_COLOR_ID_GREEN>;
 		};
 
-		chan@2 {
+		led@2 {
 			chan-name = "B";
 			led-cur = /bits/ 8 <0x20>;
 			max-cur = /bits/ 8 <0x60>;
@@ -302,7 +308,6 @@
 		compatible = "atmel,24c128";
 		reg = <0x57>;
 		pagesize = <64>;
-		status = "okay";
 	};
 
 	touchscreen: touchscreen@5c {
@@ -312,7 +317,7 @@
 		interrupt-parent = <&gpio4>;
 		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
 		attb-gpio = <&gpio4 5 GPIO_ACTIVE_HIGH>;
-		reset-gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
 		touchscreen-size-x = <800>;
 		touchscreen-size-y = <480>;
 		status = "disabled";
@@ -501,7 +506,7 @@
 		>;
 	};
 
-	pinctrl_usbh1_vbus: usbh1-vbus {
+	pinctrl_usbh1_vbus: usbh1-vbusgrp {
 		fsl,pins = <
 			MX6QDL_PAD_ENET_TXD1__GPIO1_IO29	0x98
 		>;
@@ -514,7 +519,7 @@
 		>;
 	};
 
-	pinctrl_usbotg_vbus: usbotg-vbus {
+	pinctrl_usbotg_vbus: usbotg-vbusgrp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D22__GPIO3_IO22	0x98
 		>;
diff --git a/arch/arm/boot/dts/imx6dl-yapp4-draco.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-draco.dts
index a38c407fd837..a38c407fd837 100644
--- a/arch/arm/boot/dts/imx6dl-yapp4-draco.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-draco.dts
diff --git a/arch/arm/boot/dts/imx6dl-yapp4-hydra.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-hydra.dts
index a19609c7c7c0..a19609c7c7c0 100644
--- a/arch/arm/boot/dts/imx6dl-yapp4-hydra.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-hydra.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-lynx.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-lynx.dts
new file mode 100644
index 000000000000..5c2cd517589b
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-lynx.dts
@@ -0,0 +1,58 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2021 Y Soft Corporation, a.s.
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6dl-yapp43-common.dtsi"
+
+/ {
+	model = "Y Soft IOTA Lynx i.MX6DualLite board";
+	compatible = "ysoft,imx6dl-yapp4-lynx", "fsl,imx6dl";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x40000000>;
+	};
+};
+
+&backlight {
+	status = "okay";
+};
+
+&lcd_display {
+	status = "okay";
+};
+
+&leds {
+	status = "okay";
+};
+
+&panel {
+	status = "okay";
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&reg_usb_h1_vbus {
+	status = "okay";
+};
+
+&touchscreen {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbphy2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6dl-yapp4-orion.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-orion.dts
index 884b236746bb..884b236746bb 100644
--- a/arch/arm/boot/dts/imx6dl-yapp4-orion.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-orion.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-phoenix.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-phoenix.dts
new file mode 100644
index 000000000000..e0292f11d03e
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-phoenix.dts
@@ -0,0 +1,42 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2021 Y Soft Corporation, a.s.
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6dl-yapp43-common.dtsi"
+
+/ {
+	model = "Y Soft IOTA Phoenix i.MX6DualLite board";
+	compatible = "ysoft,imx6dl-yapp4-phoenix", "fsl,imx6dl";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x40000000>;
+	};
+};
+
+&aliases {
+	/delete-property/ ethernet1;
+};
+
+&gpio_keys {
+	status = "okay";
+};
+
+&reg_usb_h1_vbus {
+	status = "okay";
+};
+
+&switch_ports {
+	/delete-node/ port@2;
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbphy2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6dl-yapp4-ursa.dts b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-ursa.dts
index f6ae24efd4aa..f6ae24efd4aa 100644
--- a/arch/arm/boot/dts/imx6dl-yapp4-ursa.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp4-ursa.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6dl-yapp43-common.dtsi b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp43-common.dtsi
new file mode 100644
index 000000000000..2f42c56c21f6
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl-yapp43-common.dtsi
@@ -0,0 +1,615 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2021 Y Soft Corporation, a.s.
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	aliases: aliases {
+		ethernet1 = &eth1;
+		ethernet2 = &eth2;
+		mmc0 = &usdhc3;
+		mmc1 = &usdhc4;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 500000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 32 64 128 255>;
+		default-brightness-level = <32>;
+		num-interpolated-steps = <8>;
+		power-supply = <&sw2_reg>;
+		status = "disabled";
+	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+		status = "disabled";
+
+		button {
+			label = "Factory RESET";
+			linux,code = <BTN_0>;
+			gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	lcd_display: display {
+		compatible = "fsl,imx-parallel-display";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interface-pix-fmt = "rgb24";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu1>;
+		status = "disabled";
+
+		port@0 {
+			reg = <0>;
+
+			lcd_display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			lcd_display_out: endpoint {
+				remote-endpoint = <&lcd_panel_in>;
+			};
+		};
+	};
+
+	panel: panel {
+		compatible = "dataimage,scf0700c48ggu18";
+		power-supply = <&sw2_reg>;
+		backlight = <&backlight>;
+		enable-gpios = <&gpio3 7 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
+	};
+
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh1_vbus>;
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		status = "disabled";
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbotg_vbus>;
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii-id";
+	phy-supply = <&sw2_reg>;
+	status = "okay";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		switch@0 {
+			compatible = "marvell,mv88e6085";
+			reg = <0>;
+			reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+
+			switch_ports: ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ethphy0: port@0 {
+					reg = <0>;
+					label = "cpu";
+					phy-mode = "rgmii-id";
+					ethernet = <&fec>;
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+
+				eth2: port@1 {
+					reg = <1>;
+					label = "eth2";
+					phy-handle = <&phy_port1>;
+				};
+
+				eth1: port@2 {
+					reg = <2>;
+					label = "eth1";
+					phy-handle = <&phy_port2>;
+				};
+			};
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy_port1: switchphy@11 {
+					reg = <0x11>;
+				};
+
+				phy_port2: switchphy@12 {
+					reg = <0x12>;
+				};
+			};
+		};
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	pmic@8 {
+		compatible = "fsl,pfuze200";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		reg = <0x8>;
+
+		regulators {
+			sw1a_reg: sw1ab {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3a_reg: sw3a {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3b_reg: sw3b {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+			};
+
+			vgen1_reg: vgen1 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen2_reg: vgen2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen3_reg: vgen3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen4_reg: vgen4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vgen5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vgen6 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vsnvs_reg: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	leds: led-controller@30 {
+		compatible = "ti,lp5562";
+		reg = <0x30>;
+		clock-mode = /bits/ 8 <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+
+		led@0 {
+			chan-name = "R";
+			led-cur = /bits/ 8 <0x6e>;
+			max-cur = /bits/ 8 <0xc8>;
+			reg = <0>;
+			color = <LED_COLOR_ID_RED>;
+		};
+
+		led@1 {
+			chan-name = "G";
+			led-cur = /bits/ 8 <0xbe>;
+			max-cur = /bits/ 8 <0xc8>;
+			reg = <1>;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+
+		led@2 {
+			chan-name = "B";
+			led-cur = /bits/ 8 <0xbe>;
+			max-cur = /bits/ 8 <0xc8>;
+			reg = <2>;
+			color = <LED_COLOR_ID_BLUE>;
+		};
+	};
+
+	eeprom@57 {
+		compatible = "atmel,24c128";
+		reg = <0x57>;
+		pagesize = <64>;
+	};
+
+	touchscreen: touchscreen@5c {
+		compatible = "pixcir,pixcir_tangoc";
+		reg = <0x5c>;
+		pinctrl-0 = <&pinctrl_touch>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+		attb-gpio = <&gpio4 5 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+		touchscreen-size-x = <800>;
+		touchscreen-size-y = <480>;
+		status = "disabled";
+	};
+
+	rtc: rtc@68 {
+		compatible = "dallas,ds1341";
+		reg = <0x68>;
+	};
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "disabled";
+
+	oled_1309: oled@3c {
+		compatible = "solomon,ssd1309fb-i2c";
+		reg = <0x3c>;
+		solomon,height = <64>;
+		solomon,width = <128>;
+		solomon,page-offset = <0>;
+		solomon,segment-no-remap;
+		solomon,prechargep2 = <15>;
+		reset-gpios = <&gpio_oled 1 GPIO_ACTIVE_LOW>;
+		vbat-supply = <&sw2_reg>;
+		status = "disabled";
+	};
+
+	oled_1305: oled@3d {
+		compatible = "solomon,ssd1305fb-i2c";
+		reg = <0x3d>;
+		solomon,height = <64>;
+		solomon,width = <128>;
+		solomon,page-offset = <0>;
+		solomon,col-offset = <4>;
+		solomon,prechargep2 = <15>;
+		reset-gpios = <&gpio_oled 1 GPIO_ACTIVE_LOW>;
+		vbat-supply = <&sw2_reg>;
+		status = "disabled";
+	};
+
+	gpio_oled: gpio@41 {
+		compatible = "nxp,pca9536";
+		gpio-controller;
+		#gpio-cells = <2>;
+		reg = <0x41>;
+		vcc-supply = <&sw2_reg>;
+		status = "disabled";
+	};
+
+	touchkeys: keys@5a {
+		compatible = "fsl,mpr121-touchkey";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touchkeys>;
+		reg = <0x5a>;
+		vdd-supply = <&sw2_reg>;
+		autorepeat;
+		linux,keycodes = <KEY_1>, <KEY_2>, <KEY_3>, <KEY_4>, <KEY_5>,
+				<KEY_6>, <KEY_7>, <KEY_8>, <KEY_9>,
+				<KEY_BACKSPACE>, <KEY_0>, <KEY_ENTER>;
+		poll-interval = <50>;
+		status = "disabled";
+	};
+};
+
+&iomuxc {
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b020
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b020
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b020
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b020
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b020
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b020
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b020
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b020
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b020
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b020
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b020
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b020
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b020
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b020
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b010
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x1b010
+			MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25	0x1b098
+		>;
+	};
+
+	pinctrl_gpio_keys: gpiokeysgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_0__GPIO1_IO00	0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL	0x4001b899
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA	0x4001b899
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_3__I2C3_SCL	0x4001b899
+			MX6QDL_PAD_GPIO_6__I2C3_SDA	0x4001b899
+		>;
+	};
+
+	pinctrl_ipu1: ipu1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_DA7__GPIO3_IO07                  0x1b0b0
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x10
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x10
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x10
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x10
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x10
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x10
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x10
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x10
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x10
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x10
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x10
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x10
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x10
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x10
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x10
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x10
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x10
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x10
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x10
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x10
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x10
+			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18	0x10
+			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19	0x10
+			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20	0x10
+			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21	0x10
+			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22	0x10
+			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23	0x10
+		>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_18__GPIO7_IO13	0x1b098
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__PWM1_OUT	0x8
+		>;
+	};
+
+	pinctrl_touch: touchgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_19__GPIO4_IO05	0x1b098
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02	0x1b098
+		>;
+	};
+
+	pinctrl_touchkeys: touchkeysgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12	0x1b098
+			MX6QDL_PAD_GPIO_5__GPIO1_IO05	0x1b098
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0a8
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0a8
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_7__UART2_TX_DATA	0x1b098
+			MX6QDL_PAD_GPIO_8__UART2_RX_DATA	0x1b098
+		>;
+	};
+
+	pinctrl_usbh1: usbh1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D30__USB_H1_OC	0x1b098
+		>;
+	};
+
+	pinctrl_usbh1_vbus: usbh1-vbusgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_TXD1__GPIO1_IO29	0x98
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x1b098
+			MX6QDL_PAD_EIM_D21__USB_OTG_OC		0x1b098
+		>;
+	};
+
+	pinctrl_usbotg_vbus: usbotg-vbusgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22	0x98
+		>;
+	};
+
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD	0x1f069
+			MX6QDL_PAD_SD4_CLK__SD4_CLK	0x10069
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0	0x17069
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1	0x17069
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2	0x17069
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3	0x17069
+			MX6QDL_PAD_SD4_DAT4__SD4_DATA4	0x17069
+			MX6QDL_PAD_SD4_DAT5__SD4_DATA5	0x17069
+			MX6QDL_PAD_SD4_DAT6__SD4_DATA6	0x17069
+			MX6QDL_PAD_SD4_DAT7__SD4_DATA7	0x17069
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__WDOG2_B	0x1b0b0
+		>;
+	};
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&lcd_display_in>;
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "disabled";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "disabled";
+};
+
+&usbh1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbh1>;
+	vbus-supply = <&reg_usb_h1_vbus>;
+	over-current-active-low;
+	status = "disabled";
+};
+
+&usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	vbus-supply = <&reg_usb_otg_vbus>;
+	over-current-active-low;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&usbphy1 {
+	fsl,tx-d-cal = <106>;
+	status = "okay";
+};
+
+&usbphy2 {
+	fsl,tx-d-cal = <109>;
+	status = "disabled";
+};
+
+&usdhc4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	bus-width = <8>;
+	non-removable;
+	no-1-8-v;
+	keep-power-in-suspend;
+	vmmc-supply = <&sw2_reg>;
+	status = "okay";
+};
+
+&wdog1 {
+	status = "disabled";
+};
+
+&wdog2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6dl.dtsi b/arch/arm/boot/dts/nxp/imx/imx6dl.dtsi
index fdd81fdc3f35..dc919e09a505 100644
--- a/arch/arm/boot/dts/imx6dl.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6dl.dtsi
@@ -80,10 +80,13 @@
 		};
 	};
 
-	soc {
+	soc: soc {
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval-v1.2.dts b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval-v1.2.dts
new file mode 100644
index 000000000000..15d4a98ee976
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval-v1.2.dts
@@ -0,0 +1,200 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2024 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6q-apalis-eval.dtsi"
+
+/ {
+	model = "Toradex Apalis iMX6Q/D Module on Apalis Evaluation Board v1.2";
+	compatible = "toradex,apalis_imx6q-eval-v1.2", "toradex,apalis_imx6q",
+		     "fsl,imx6q";
+
+	reg_3v3_mmc: regulator-3v3-mmc {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 0 GPIO_ACTIVE_HIGH>;
+		off-on-delay-us = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_enable_3v3_mmc>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "3.3V_MMC";
+		startup-delay-us = <10000>;
+	};
+
+	reg_3v3_sd: regulator-3v3-sd {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+		off-on-delay-us = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_enable_3v3_sd>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "3.3V_SD";
+		startup-delay-us = <10000>;
+	};
+
+	reg_can1: regulator-can1 {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_enable_can1_power>;
+		regulator-name = "5V_SW_CAN1";
+		startup-delay-us = <10000>;
+	};
+
+	reg_can2: regulator-can2 {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_enable_can2_power>;
+		regulator-name = "5V_SW_CAN2";
+		startup-delay-us = <10000>;
+	};
+
+	sound-carrier {
+		compatible = "simple-audio-card";
+		simple-audio-card,bitclock-master = <&codec_dai>;
+		simple-audio-card,format = "i2s";
+		simple-audio-card,frame-master = <&codec_dai>;
+		simple-audio-card,name = "apalis-nau8822";
+		simple-audio-card,routing =
+			"Headphones", "LHP",
+			"Headphones", "RHP",
+			"Speaker", "LSPK",
+			"Speaker", "RSPK",
+			"Line Out", "AUXOUT1",
+			"Line Out", "AUXOUT2",
+			"LAUX", "Line In",
+			"RAUX", "Line In",
+			"LMICP", "Mic In",
+			"RMICP", "Mic In";
+		simple-audio-card,widgets =
+			"Headphones", "Headphones",
+			"Line Out", "Line Out",
+			"Speaker", "Speaker",
+			"Microphone", "Mic In",
+			"Line", "Line In";
+
+		codec_dai: simple-audio-card,codec {
+			sound-dai = <&nau8822_1a>;
+			system-clock-frequency = <12288000>;
+		};
+
+		simple-audio-card,cpu {
+			sound-dai = <&ssi2>;
+		};
+	};
+};
+
+&can1 {
+	xceiver-supply = <&reg_can1>;
+	status = "okay";
+};
+
+&can2 {
+	xceiver-supply = <&reg_can2>;
+	status = "okay";
+};
+
+/* I2C1_SDA/SCL on MXM3 209/211 */
+&i2c1 {
+	/* Audio Codec */
+	nau8822_1a: audio-codec@1a {
+		compatible = "nuvoton,nau8822";
+		reg = <0x1a>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_nau8822>;
+		#sound-dai-cells = <0>;
+	};
+
+	/* Current measurement into module VCC */
+	hwmon@40 {
+		compatible = "ti,ina219";
+		reg = <0x40>;
+		shunt-resistor = <5000>;
+	};
+
+	/* Temperature Sensor */
+	temperature-sensor@4f {
+		compatible = "ti,tmp75c";
+		reg = <0x4f>;
+	};
+
+	/* EEPROM */
+	eeprom@57 {
+		compatible = "st,24c02", "atmel,24c02";
+		reg = <0x57>;
+		pagesize = <16>;
+		size = <256>;
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&ssi2 {
+	status = "okay";
+};
+
+/* MMC1 */
+&usdhc1 {
+	bus-width = <4>;
+	pinctrl-0 = <&pinctrl_usdhc1_4bit &pinctrl_mmc_cd>;
+	vmmc-supply = <&reg_3v3_mmc>;
+	status = "okay";
+};
+
+/* SD1 */
+&usdhc2 {
+	cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&pinctrl_usdhc2 &pinctrl_sd_cd>;
+	vmmc-supply = <&reg_3v3_sd>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_enable_3v3_mmc: enable3v3mmcgrp {
+		fsl,pins = <
+			/* MMC1_PWR_CTRL */
+			MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b0b0
+		>;
+	};
+
+	pinctrl_enable_3v3_sd: enable3v3sdgrp {
+		fsl,pins = <
+			/* SD1_PWR_CTRL */
+			MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0
+		>;
+	};
+
+	pinctrl_enable_can1_power: enablecan1powergrp {
+		fsl,pins = <
+			/* CAN1_PWR_EN */
+			MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x1b0b0
+		>;
+	};
+
+	pinctrl_enable_can2_power: enablecan2powergrp {
+		fsl,pins = <
+			/* CAN2_PWR_EN */
+			MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0
+		>;
+	};
+
+	pinctrl_nau8822: nau8822grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT16__AUD5_TXC	0x130b0
+			MX6QDL_PAD_DISP0_DAT17__AUD5_TXD	0x130b0
+			MX6QDL_PAD_DISP0_DAT18__AUD5_TXFS	0x130b0
+			MX6QDL_PAD_DISP0_DAT19__AUD5_RXD	0x130b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dts b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dts
new file mode 100644
index 000000000000..1f2200f50059
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dts
@@ -0,0 +1,59 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2014-2022 Toradex
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ */
+
+/dts-v1/;
+
+#include "imx6q-apalis-eval.dtsi"
+
+/ {
+	model = "Toradex Apalis iMX6Q/D Module on Apalis Evaluation Board";
+	compatible = "toradex,apalis_imx6q-eval", "toradex,apalis_imx6q",
+		     "fsl,imx6q";
+
+	reg_pcie_switch: regulator-pcie-switch {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+		regulator-max-microvolt = <1800000>;
+		regulator-min-microvolt = <1800000>;
+		regulator-name = "pcie_switch";
+		startup-delay-us = <100000>;
+		status = "okay";
+	};
+};
+
+&can1 {
+	xceiver-supply = <&reg_3v3_sw>;
+	status = "okay";
+};
+
+&can2 {
+	xceiver-supply = <&reg_3v3_sw>;
+	status = "okay";
+};
+
+&pcie {
+	vpcie-supply = <&reg_pcie_switch>;
+	status = "okay";
+};
+
+&sound_spdif {
+	status = "okay";
+};
+
+/* MMC1 */
+&usdhc1 {
+	status = "okay";
+};
+
+/* SD1 */
+&usdhc2 {
+	cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2 &pinctrl_sd_cd>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dtsi b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dtsi
new file mode 100644
index 000000000000..b6c45ad3f430
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-eval.dtsi
@@ -0,0 +1,120 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2014-2024 Toradex
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx6q.dtsi"
+#include "imx6qdl-apalis.dtsi"
+
+/ {
+	aliases {
+		i2c0 = &i2c1;
+		i2c1 = &i2c3;
+		i2c2 = &i2c2;
+		rtc0 = &rtc_i2c;
+		rtc1 = &snvs_rtc;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_3v3_sw: regulator-3v3-sw {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "3.3V_SW";
+	};
+};
+
+&i2c1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	/* M41T0M6 real time clock on carrier board */
+	rtc_i2c: rtc@68 {
+		compatible = "st,m41t0";
+		reg = <0x68>;
+	};
+};
+
+/*
+ * I2C3_SDA/SCL (CAM) on MXM3 pin 201/203 (e.g. camera sensor on carrier
+ * board)
+ */
+&i2c3 {
+	status = "okay";
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_reset_moci>;
+	/* active-high meaning opposite of regular PERST# active-low polarity */
+	reset-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+	reset-gpio-active-high;
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&pwm2 {
+	status = "okay";
+};
+
+&pwm3 {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+&reg_usb_host_vbus {
+	status = "okay";
+};
+
+&reg_usb_otg_vbus {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&spdif {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&usbh1 {
+	disable-over-current;
+	vbus-supply = <&reg_usb_host_vbus>;
+	status = "okay";
+};
+
+&usbotg {
+	disable-over-current;
+	vbus-supply = <&reg_usb_otg_vbus>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-apalis-ixora-v1.1.dts b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-ixora-v1.1.dts
new file mode 100644
index 000000000000..44637d606e61
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-ixora-v1.1.dts
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2014-2022 Toradex
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ */
+
+#include "imx6q-apalis-ixora-v1.2.dts"
+
+/ {
+	model = "Toradex Apalis iMX6Q/D Module on Ixora Carrier Board V1.1";
+	compatible = "toradex,apalis_imx6q-ixora-v1.1", "toradex,apalis_imx6q",
+		     "fsl,imx6q";
+
+
+};
+
+/delete-node/ &eeprom;
+/delete-node/ &reg_3v3_vmmc;
+/delete-node/ &reg_can1_supply;
+/delete-node/ &reg_can2_supply;
+
+&can1 {
+	/delete-property/ xceiver-supply;
+};
+
+&can2 {
+	/delete-property/ xceiver-supply;
+};
+
+/* MMC1 */
+&usdhc1 {
+	/delete-property/ cap-power-off-card;
+	/delete-property/ pinctrl-1;
+	/delete-property/ vmmc-supply;
+	pinctrl-names = "default";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-apalis-ixora-v1.2.dts b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-ixora-v1.2.dts
new file mode 100644
index 000000000000..3ac7a4501620
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-ixora-v1.2.dts
@@ -0,0 +1,280 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2014-2022 Toradex
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx6q.dtsi"
+#include "imx6qdl-apalis.dtsi"
+
+/ {
+	model = "Toradex Apalis iMX6Q/D Module on Ixora Carrier Board V1.2";
+	compatible = "toradex,apalis_imx6q-ixora-v1.2", "toradex,apalis_imx6q",
+		     "fsl,imx6q";
+
+	aliases {
+		i2c0 = &i2c1;
+		i2c1 = &i2c3;
+		i2c2 = &i2c2;
+		rtc0 = &rtc_i2c;
+		rtc1 = &snvs_rtc;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds_ixora>;
+
+		led4-green {
+			gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+			label = "LED_4_GREEN";
+		};
+
+		led4-red {
+			gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+			label = "LED_4_RED";
+		};
+
+		led5-green {
+			gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+			label = "LED_5_GREEN";
+		};
+
+		led5-red {
+			gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+			label = "LED_5_RED";
+		};
+	};
+
+	reg_3v3_vmmc: regulator-3v3-vmmc {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 0 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_enable_3v3_vmmc>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "3v3_vmmc";
+		startup-delay-us = <100>;
+	};
+
+	reg_can1_supply: regulator-can1-supply {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_enable_can1_power>;
+		regulator-name = "can1_supply";
+		startup-delay-us = <1000>;
+	};
+
+	reg_can2_supply: regulator-can2-supply {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_enable_can2_power>;
+		regulator-name = "can2_supply";
+		startup-delay-us = <1000>;
+	};
+};
+
+&can1 {
+	xceiver-supply = <&reg_can1_supply>;
+	status = "okay";
+};
+
+&can2 {
+	xceiver-supply = <&reg_can2_supply>;
+	status = "okay";
+};
+
+&gpio1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart24_forceoff>;
+
+	/*
+	 * uart-2-4-on-x21-enable-hog enables the UART transceiver for Apalis
+	 * UART2 and UART3. If one wants to disable the transceiver force
+	 * the GPIO to output-low, if one wants to control the transceiver
+	 * from user space delete the hog node.
+	 */
+	uart-2-4-on-x21-enable-hog {
+		gpio-hog;
+		gpios = <11 GPIO_ACTIVE_HIGH>; /* MXM3 180 */
+		output-high;
+	};
+};
+
+/* I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier board) */
+&i2c1 {
+	status = "okay";
+
+	/* M41T0M6 real time clock on carrier board */
+	rtc_i2c: rtc@68 {
+		compatible = "st,m41t0";
+		reg = <0x68>;
+	};
+
+	eeprom: eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
+/*
+ * I2C3_SDA/SCL (CAM) on MXM3 pin 201/203 (e.g. camera sensor on carrier
+ * board)
+ */
+&i2c3 {
+	status = "okay";
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_reset_moci>;
+	/* active-high meaning opposite of regular PERST# active-low polarity */
+	reset-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+	reset-gpio-active-high;
+	status = "okay";
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&pwm2 {
+	status = "okay";
+};
+
+&pwm3 {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+&reg_usb_host_vbus {
+	status = "okay";
+};
+
+&reg_usb_otg_vbus {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&sound_spdif {
+	status = "okay";
+};
+
+&spdif {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&usbh1 {
+	disable-over-current;
+	vbus-supply = <&reg_usb_host_vbus>;
+	status = "okay";
+};
+
+&usbotg {
+	disable-over-current;
+	vbus-supply = <&reg_usb_otg_vbus>;
+	status = "okay";
+};
+
+/* MMC1 */
+&usdhc1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc1_4bit &pinctrl_mmc_cd>;
+	pinctrl-1 = <&pinctrl_usdhc1_4bit_sleep &pinctrl_mmc_cd_sleep>;
+	bus-width = <4>;
+	cap-power-off-card;
+	vmmc-supply = <&reg_3v3_vmmc>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_enable_3v3_vmmc: enable3v3vmmcgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b0b0
+		>;
+	};
+
+	pinctrl_enable_can1_power: enablecan1powergrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x1b0b0
+		>;
+	};
+
+	pinctrl_enable_can2_power: enablecan2powergrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_DA15__GPIO3_IO15 0x1b0b0
+		>;
+	};
+
+	pinctrl_uart24_forceoff: uart24forceoffgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__GPIO1_IO11 0x1b0b0
+		>;
+	};
+
+	pinctrl_leds_ixora: ledsixoragrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x1b0b0
+			MX6QDL_PAD_SD2_DAT3__GPIO1_IO12 0x1b0b0
+			MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0
+			MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0
+		>;
+	};
+
+	pinctrl_mmc_cd_sleep: mmccdslpgrp {
+		fsl,pins = <
+			 /* MMC1 CD */
+			MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x0
+		>;
+	};
+
+	pinctrl_usdhc1_4bit_sleep: usdhc1-4bitslpgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD     0x3000
+			MX6QDL_PAD_SD1_CLK__SD1_CLK     0x3000
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0  0x3000
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1  0x3000
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2  0x3000
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3  0x3000
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6q-apalis-ixora.dts b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-ixora.dts
index 62e72773e53b..f338be435277 100644
--- a/arch/arm/boot/dts/imx6q-apalis-ixora.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-ixora.dts
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2014-2020 Toradex
+ * Copyright 2014-2022 Toradex
  * Copyright 2012 Freescale Semiconductor, Inc.
  * Copyright 2011 Linaro Ltd.
  */
@@ -30,95 +30,33 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpio_keys>;
-
-		wakeup {
-			label = "Wake-Up";
-			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_WAKEUP>;
-			debounce-interval = <10>;
-			wakeup-source;
-		};
-	};
-
-	lcd_display: disp0 {
-		compatible = "fsl,imx-parallel-display";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		interface-pix-fmt = "rgb24";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_ipu1_lcdif>;
-		status = "okay";
-
-		port@0 {
-			reg = <0>;
-
-			lcd_display_in: endpoint {
-				remote-endpoint = <&ipu1_di1_disp1>;
-			};
-		};
-
-		port@1 {
-			reg = <1>;
-
-			lcd_display_out: endpoint {
-				remote-endpoint = <&lcd_panel_in>;
-			};
-		};
-	};
-
-	panel: panel {
-		/*
-		 * edt,et057090dhu: EDT 5.7" LCD TFT
-		 * edt,et070080dh6: EDT 7.0" LCD TFT
-		 */
-		compatible = "edt,et057090dhu";
-		backlight = <&backlight>;
-
-		port {
-			lcd_panel_in: endpoint {
-				remote-endpoint = <&lcd_display_out>;
-			};
-		};
-	};
-
 	leds {
 		compatible = "gpio-leds";
-
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_leds_ixora>;
 
 		led4-green {
-			label = "LED_4_GREEN";
 			gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+			label = "LED_4_GREEN";
 		};
 
 		led4-red {
-			label = "LED_4_RED";
 			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
+			label = "LED_4_RED";
 		};
 
 		led5-green {
-			label = "LED_5_GREEN";
 			gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+			label = "LED_5_GREEN";
 		};
 
 		led5-red {
-			label = "LED_5_RED";
 			gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+			label = "LED_5_RED";
 		};
 	};
 };
 
-&backlight {
-	brightness-levels = <0 127 191 223 239 247 251 255>;
-	default-brightness-level = <1>;
-	status = "okay";
-};
-
 &can1 {
 	status = "okay";
 };
@@ -127,27 +65,10 @@
 	status = "okay";
 };
 
-&hdmi {
-	status = "okay";
-};
-
 /* I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier board) */
 &i2c1 {
 	status = "okay";
 
-	/*
-	 * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
-	 * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
-	 */
-	touchscreen@4a {
-		compatible = "atmel,maxtouch";
-		reg = <0x4a>;
-		interrupt-parent = <&gpio6>;
-		interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
-		reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>; /* SODIMM 13 */
-		status = "disabled";
-	};
-
 	eeprom@50 {
 		compatible = "atmel,24c02";
 		reg = <0x50>;
@@ -168,14 +89,6 @@
 	status = "okay";
 };
 
-&ipu1_di1_disp1 {
-	remote-endpoint = <&lcd_display_in>;
-};
-
-&ldb {
-	status = "okay";
-};
-
 &pcie {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_reset_moci>;
@@ -201,11 +114,11 @@
 	status = "okay";
 };
 
-&reg_usb_otg_vbus {
+&reg_usb_host_vbus {
 	status = "okay";
 };
 
-&reg_usb_host_vbus {
+&reg_usb_otg_vbus {
 	status = "okay";
 };
 
@@ -238,32 +151,26 @@
 };
 
 &usbh1 {
+	disable-over-current;
 	vbus-supply = <&reg_usb_host_vbus>;
 	status = "okay";
 };
 
 &usbotg {
+	disable-over-current;
 	vbus-supply = <&reg_usb_otg_vbus>;
 	status = "okay";
 };
 
 /* SD1 */
 &usdhc2 {
+	cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc2 &pinctrl_sd_cd>;
-	cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
 &iomuxc {
-	/* Mux the Apalis GPIOs */
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_apalis_gpio1 &pinctrl_apalis_gpio2
-		     &pinctrl_apalis_gpio3 &pinctrl_apalis_gpio4
-		     &pinctrl_apalis_gpio5 &pinctrl_apalis_gpio6
-		     &pinctrl_apalis_gpio7 &pinctrl_apalis_gpio8
-		    >;
-
 	pinctrl_leds_ixora: ledsixoragrp {
 		fsl,pins = <
 			MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x1b0b0
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-apalis-v1.2-eval-v1.2.dts b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-v1.2-eval-v1.2.dts
new file mode 100644
index 000000000000..908dab57fd87
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-v1.2-eval-v1.2.dts
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/* Copyright (c) 2025 Toradex */
+
+/dts-v1/;
+
+#include "imx6q-apalis-eval-v1.2.dts"
+#include "imx6qdl-apalis-v1.2.dtsi"
+
+/ {
+	model = "Toradex Apalis iMX6Q/D Module V1.2+ on Apalis Evaluation Board v1.2";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-apalis-v1.2-eval.dts b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-v1.2-eval.dts
new file mode 100644
index 000000000000..5463d4127382
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-v1.2-eval.dts
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/* Copyright (c) 2025 Toradex */
+
+/dts-v1/;
+
+#include "imx6q-apalis-eval.dts"
+#include "imx6qdl-apalis-v1.2.dtsi"
+
+/ {
+	model = "Toradex Apalis iMX6Q/D Module V1.2+ on Apalis Evaluation Board";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-apalis-v1.2-ixora-v1.1.dts b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-v1.2-ixora-v1.1.dts
new file mode 100644
index 000000000000..84eabf81ba84
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-v1.2-ixora-v1.1.dts
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/* Copyright (c) 2025 Toradex */
+
+/dts-v1/;
+
+#include "imx6q-apalis-ixora-v1.1.dts"
+#include "imx6qdl-apalis-v1.2.dtsi"
+
+/ {
+	model = "Toradex Apalis iMX6Q/D Module V1.2+ on Ixora Carrier Board V1.1";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-apalis-v1.2-ixora-v1.2.dts b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-v1.2-ixora-v1.2.dts
new file mode 100644
index 000000000000..d7cfab4de457
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-v1.2-ixora-v1.2.dts
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/* Copyright (c) 2025 Toradex */
+
+/dts-v1/;
+
+#include "imx6q-apalis-ixora-v1.2.dts"
+#include "imx6qdl-apalis-v1.2.dtsi"
+
+/ {
+	model = "Toradex Apalis iMX6Q/D Module V1.2+ on Ixora Carrier Board V1.2";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-apalis-v1.2-ixora.dts b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-v1.2-ixora.dts
new file mode 100644
index 000000000000..189b074e31ce
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-apalis-v1.2-ixora.dts
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/* Copyright (c) 2025 Toradex */
+
+/dts-v1/;
+
+#include "imx6q-apalis-ixora.dts"
+#include "imx6qdl-apalis-v1.2.dtsi"
+
+/ {
+	model = "Toradex Apalis iMX6Q/D Module V1.2+ on Ixora Carrier Board";
+};
diff --git a/arch/arm/boot/dts/imx6q-apf6dev.dts b/arch/arm/boot/dts/nxp/imx/imx6q-apf6dev.dts
index 664b0af8f0bb..664b0af8f0bb 100644
--- a/arch/arm/boot/dts/imx6q-apf6dev.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-apf6dev.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-arm2.dts b/arch/arm/boot/dts/nxp/imx/imx6q-arm2.dts
new file mode 100644
index 000000000000..235148c1edf1
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-arm2.dts
@@ -0,0 +1,216 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include "imx6q.dtsi"
+
+/ {
+	model = "Freescale i.MX6 Quad Armadillo2 Board";
+	compatible = "fsl,imx6q-arm2", "fsl,imx6q";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x80000000>;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 0>;
+		enable-active-high;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		debug-led {
+			label = "Heartbeat";
+			gpios = <&gpio3 25 0>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	status = "disabled"; /* gpmi nand conflicts with SD */
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D25__GPIO3_IO25 0x80000000
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL1__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_KEY_COL2__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
+			MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
+		>;
+	};
+
+	pinctrl_gpmi_nand: gpminandgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CLE__NAND_CLE		0xb0b1
+			MX6QDL_PAD_NANDF_ALE__NAND_ALE		0xb0b1
+			MX6QDL_PAD_NANDF_WP_B__NAND_WP_B	0xb0b1
+			MX6QDL_PAD_NANDF_RB0__NAND_READY_B	0xb000
+			MX6QDL_PAD_NANDF_CS0__NAND_CE0_B	0xb0b1
+			MX6QDL_PAD_NANDF_CS1__NAND_CE1_B	0xb0b1
+			MX6QDL_PAD_SD4_CMD__NAND_RE_B		0xb0b1
+			MX6QDL_PAD_SD4_CLK__NAND_WE_B		0xb0b1
+			MX6QDL_PAD_NANDF_D0__NAND_DATA00	0xb0b1
+			MX6QDL_PAD_NANDF_D1__NAND_DATA01	0xb0b1
+			MX6QDL_PAD_NANDF_D2__NAND_DATA02	0xb0b1
+			MX6QDL_PAD_NANDF_D3__NAND_DATA03	0xb0b1
+			MX6QDL_PAD_NANDF_D4__NAND_DATA04	0xb0b1
+			MX6QDL_PAD_NANDF_D5__NAND_DATA05	0xb0b1
+			MX6QDL_PAD_NANDF_D6__NAND_DATA06	0xb0b1
+			MX6QDL_PAD_NANDF_D7__NAND_DATA07	0xb0b1
+			MX6QDL_PAD_SD4_DAT0__NAND_DQS		0x00b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D26__UART2_RX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D27__UART2_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B	0x1b0b1
+			MX6QDL_PAD_EIM_D29__UART2_DTE_RTS_B	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA	0x1b0b1
+			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4		0x17059
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5		0x17059
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6		0x17059
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7		0x17059
+		>;
+	};
+
+	pinctrl_usdhc3_cdwp: usdhc3cdwpgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CS0__GPIO6_IO11 0x80000000
+			MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x80000000
+		>;
+	};
+
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
+			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059
+			MX6QDL_PAD_SD4_DAT4__SD4_DATA4		0x17059
+			MX6QDL_PAD_SD4_DAT5__SD4_DATA5		0x17059
+			MX6QDL_PAD_SD4_DAT6__SD4_DATA6		0x17059
+			MX6QDL_PAD_SD4_DAT7__SD4_DATA7		0x17059
+		>;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii";
+	/delete-property/ interrupts;
+	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
+			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
+	fsl,err006687-workaround-present;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc3 {
+	cd-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&reg_3p3v>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3
+		     &pinctrl_usdhc3_cdwp>;
+	status = "okay";
+};
+
+&usdhc4 {
+	non-removable;
+	vmmc-supply = <&reg_3p3v>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	fsl,dte-mode;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6q-b450v3.dts b/arch/arm/boot/dts/nxp/imx/imx6q-b450v3.dts
index d994b32ad825..d994b32ad825 100644
--- a/arch/arm/boot/dts/imx6q-b450v3.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-b450v3.dts
diff --git a/arch/arm/boot/dts/imx6q-b650v3.dts b/arch/arm/boot/dts/nxp/imx/imx6q-b650v3.dts
index fa1a1df37cde..b0d345f5d071 100644
--- a/arch/arm/boot/dts/imx6q-b650v3.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-b650v3.dts
@@ -98,8 +98,8 @@
 };
 
 &usbphy1 {
-	fsl,tx-cal-45-dn-ohms = <55>;
-	fsl,tx-cal-45-dp-ohms = <55>;
+	fsl,tx-cal-45-dn-ohms = <54>;
+	fsl,tx-cal-45-dp-ohms = <54>;
 	fsl,tx-d-cal = <100>;
 };
 
diff --git a/arch/arm/boot/dts/imx6q-b850v3.dts b/arch/arm/boot/dts/nxp/imx/imx6q-b850v3.dts
index db8c332df6a1..cad112e05475 100644
--- a/arch/arm/boot/dts/imx6q-b850v3.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-b850v3.dts
@@ -227,7 +227,6 @@
 
 		#address-cells = <3>;
 		#size-cells = <2>;
-		#interrupt-cells = <1>;
 
 		bridge@2,1 {
 			compatible = "pci10b5,8605";
@@ -235,7 +234,6 @@
 
 			#address-cells = <3>;
 			#size-cells = <2>;
-			#interrupt-cells = <1>;
 
 			/* Intel Corporation I210 Gigabit Network Connection */
 			ethernet@3,0 {
@@ -250,7 +248,6 @@
 
 			#address-cells = <3>;
 			#size-cells = <2>;
-			#interrupt-cells = <1>;
 
 			/* Intel Corporation I210 Gigabit Network Connection */
 			switch_nic: ethernet@4,0 {
diff --git a/arch/arm/boot/dts/imx6q-ba16.dtsi b/arch/arm/boot/dts/nxp/imx/imx6q-ba16.dtsi
index 6330d75f8f39..53013b12c2ec 100644
--- a/arch/arm/boot/dts/imx6q-ba16.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-ba16.dtsi
@@ -55,7 +55,7 @@
 		compatible = "pwm-backlight";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_display>;
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <  0   1   2   3   4   5   6   7   8   9
 				      10  11  12  13  14  15  16  17  18  19
 				      20  21  22  23  24  25  26  27  28  29
@@ -142,7 +142,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: n25q032@0 {
+	flash: flash@0 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -222,6 +222,8 @@
 		pinctrl-0 = <&pinctrl_pmic>;
 		interrupt-parent = <&gpio7>;
 		interrupts = <13 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
 
 		onkey {
 			compatible = "dlg,da9063-onkey";
@@ -349,7 +351,6 @@
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
@@ -624,7 +625,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_reset: usdhc3grp-reset {
+	pinctrl_usdhc3_reset: usdhc3-resetgrp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_RST__SD3_RESET   0x170F9
 		>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-bosch-acc.dts b/arch/arm/boot/dts/nxp/imx/imx6q-bosch-acc.dts
new file mode 100644
index 000000000000..d3f14b4d3b51
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-bosch-acc.dts
@@ -0,0 +1,773 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Support for the i.MX6-based Bosch ACC board.
+ *
+ * Copyright (C) 2016 Garz & Fricke GmbH
+ * Copyright (C) 2018 DENX Software Engineering GmbH, Heiko Schocher <hs@denx.de>
+ * Copyright (C) 2018 DENX Software Engineering GmbH, Niel Fourie <lusus@denx.de>
+ * Copyright (C) 2019-2021 Bosch Thermotechnik GmbH, Matthias Winker <matthias.winker@bosch.com>
+ * Copyright (C) 2022 DENX Software Engineering GmbH, Philip Oberfichtner <pro@denx.de>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "imx6q.dtsi"
+
+/ {
+	model = "Bosch ACC";
+	compatible = "bosch,imx6q-acc", "fsl,imx6q";
+
+	aliases {
+		i2c0 = &i2c1;
+		i2c1 = &i2c2;
+		i2c2 = &i2c3;
+		mmc0 = &usdhc4;
+		mmc1 = &usdhc2;
+		serial0 = &uart2;
+		serial1 = &uart1;
+	};
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x40000000>;
+	};
+
+	backlight_lvds: backlight-lvds {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 200000 0>;
+		brightness-levels = <0 61 499 1706 4079 8022 13938 22237 33328 47623 65535>;
+		num-interpolated-steps = <10>;
+		default-brightness-level = <60>;
+		power-supply = <&reg_lcd>;
+	};
+
+	panel {
+		compatible = "dataimage,fg1001l0dsswmg01";
+		backlight = <&backlight_lvds>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+
+	refclk: refclk {
+		compatible = "fixed-factor-clock";
+		#clock-cells = <0>;
+		clocks = <&clks IMX6QDL_CLK_CKO2>;
+		clock-div = <1>;
+		clock-mult = <1>;
+		clock-output-names = "12mhz_refclk";
+		assigned-clocks = <&clks IMX6QDL_CLK_CKO>,
+				  <&clks IMX6QDL_CLK_CKO2>,
+				  <&clks IMX6QDL_CLK_CKO2_SEL>;
+		assigned-clock-parents = <&clks IMX6QDL_CLK_CKO2>,
+					 <&clks IMX6QDL_CLK_CKO2_PODF>,
+					 <&clks IMX6QDL_CLK_OSC>;
+		assigned-clock-rates = <0>, <12000000>, <0>;
+	};
+
+	cpus {
+		cpu0: cpu@0 {
+			operating-points = <
+				/* kHz    uV */
+				1200000 1275000
+				996000  1225000
+				852000  1225000
+				792000  1150000
+				396000  950000
+			>;
+			fsl,soc-operating-points = <
+				/* ARM kHz  SOC-PU uV */
+				1200000 1225000
+				996000	1175000
+				852000	1175000
+				792000	1150000
+				396000	1150000
+			>;
+		};
+
+		cpu1: cpu@1 {
+			operating-points = <
+				/* kHz    uV */
+				1200000 1275000
+				996000  1225000
+				852000  1225000
+				792000  1150000
+				396000  950000
+			>;
+			fsl,soc-operating-points = <
+				/* ARM kHz  SOC-PU uV */
+				1200000 1225000
+				996000	1175000
+				852000	1175000
+				792000	1150000
+				396000	1150000
+			>;
+		};
+	};
+
+	pwm-leds {
+		compatible = "pwm-leds";
+
+		led_red: led-0 {
+			color = <LED_COLOR_ID_RED>;
+			max-brightness = <248>;
+			default-state = "off";
+			pwms = <&pwm2 0 500000 0>;
+		};
+
+		led_white: led-1 {
+			color = <LED_COLOR_ID_WHITE>;
+			max-brightness = <248>;
+			default-state = "off";
+			pwms = <&pwm3 0 500000 0>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reset_gpio_led>;
+
+		led-2 {
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio5 18 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	reg_5p0: regulator-5p0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5p0";
+	};
+
+	reg_vin: regulator-vin {
+		compatible = "regulator-fixed";
+		regulator-name = "VIN";
+		regulator-min-microvolt = <4500000>;
+		regulator-max-microvolt = <4500000>;
+		regulator-always-on;
+		vin-supply = <&reg_5p0>;
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&reg_5p0>;
+	};
+
+	reg_usb_h2_vbus: regulator-usb-h2-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_h2_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_5p0> ;
+		regulator-always-on;
+	};
+
+	reg_vsnvs: regulator-vsnvs {
+		compatible = "regulator-fixed";
+		regulator-name = "VSNVS_3V0";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		regulator-always-on;
+		vin-supply = <&reg_5p0>;
+	};
+
+	reg_lcd: regulator-lcd {
+		compatible = "regulator-fixed";
+		regulator-name = "LCD0 POWER";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lcd_enable>;
+		gpio = <&gpio3 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+
+	reg_dac: regulator-dac {
+		compatible = "regulator-fixed";
+		regulator-name = "vref_dac";
+		regulator-min-microvolt = <20000>;
+		regulator-max-microvolt = <20000>;
+		vin-supply = <&reg_5p0> ;
+		regulator-boot-on;
+	};
+
+	reg_sw4: regulator-sw4 {
+		compatible = "regulator-fixed";
+		regulator-name = "SW4_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		vin-supply = <&reg_5p0>;
+	};
+
+	reg_sys: regulator-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "SYS_4V2";
+		regulator-min-microvolt = <4200000>;
+		regulator-max-microvolt = <4200000>;
+		regulator-always-on;
+		vin-supply = <&reg_5p0>;
+	};
+};
+
+&reg_arm {
+	vin-supply = <&sw2_reg>;
+};
+
+&reg_soc {
+	vin-supply = <&sw1c_reg>;
+};
+
+&reg_vdd1p1 {
+	vin-supply = <&reg_vsnvs>;
+};
+
+&reg_vdd2p5 {
+	vin-supply = <&reg_vsnvs>;
+};
+
+&reg_vdd3p0 {
+	vin-supply = <&reg_vsnvs>;
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	clocks = <&clks IMX6QDL_CLK_ENET>,
+		<&clks IMX6QDL_CLK_ENET>,
+		<&clks IMX6QDL_CLK_ENET>,
+		<&clks IMX6QDL_CLK_ENET_REF>;
+	clock-names = "ipg", "ahb", "ptp", "enet_out";
+	phy-mode = "rmii";
+	phy-supply = <&reg_sw4>;
+	phy-handle = <&ethphy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			interrupt-parent = <&gpio1>;
+			interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
+			smsc,disable-energy-detect;
+		};
+	};
+};
+
+&gpu_vg {
+	status = "disabled";
+};
+
+&gpu_2d {
+	status = "disabled";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	pmic: pmic@8 {
+		compatible = "fsl,pfuze100";
+		reg = <0x08>;
+
+		regulators {
+			sw1c_reg: sw1c {
+				regulator-name = "VDD_SOC (sw1abc)";
+				regulator-min-microvolt = <1275000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-name = "VDD_ARM (sw2)";
+				regulator-min-microvolt = <1050000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw3a_reg: sw3a {
+				regulator-name = "DDR_1V5a";
+				regulator-boot-on;
+				regulator-always-on;
+
+			};
+
+			sw3b_reg: sw3b {
+				regulator-name = "DDR_1V5b";
+				regulator-boot-on;
+				regulator-always-on;
+
+			};
+
+			sw4_reg: sw4 {
+				regulator-name = "AUX 3V15 (sw4)";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+				regulator-boot-on;
+				regulator-always-on;
+				status = "disabled";
+			};
+
+			snvs_reg: vsnvs {
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vgen1 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+				regulator-always-on;
+			};
+
+			vgen2_reg: vgen2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+				regulator-always-on;
+			};
+
+			vgen3_reg: vgen3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen4_reg: vgen4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vgen5_reg: vgen5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vgen6_reg: vgen6 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+
+	lm75: sensor@49 {
+		compatible = "national,lm75b";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lm75>;
+		reg = <0x49>;
+	};
+
+	eeprom: eeprom@50 {
+		compatible = "atmel,24c32";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	rtc: rtc@51 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc>;
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	eeprom_ext: eeprom@50 {
+		compatible = "atmel,24c32";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	usb3503: usb@8 {
+		compatible = "smsc,usb3503";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb3503>;
+		reg = <0x08>;
+		connect-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; /* Old: 0, SS: HIGH */
+		intn-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>; /* Old: 1, SS: HIGH */
+		reset-gpios = <&gpio5 5 GPIO_ACTIVE_LOW>; /* Old: 0, SS: HIGH */
+		initial-mode = <1>;
+		clocks = <&refclk>;
+		clock-names = "refclk";
+		refclk-frequency = <12000000>;
+	};
+
+	exc3000: touchscreen@2a {
+		compatible = "eeti,exc3000";
+		reg = <0x2a>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ctouch>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
+		touchscreen-size-x = <4096>;
+		touchscreen-size-y = <4096>;
+	};
+
+	vcnl4035: light-sensor@60 {
+		compatible = "vishay,vcnl4035";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_proximity>;
+		reg = <0x60>;
+	};
+};
+
+&ldb {
+	status = "okay";
+
+	lvds0: lvds-channel@0 {
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <24>;
+
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "okay";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	rts-gpios = <&gpio7 8 GPIO_ACTIVE_HIGH>;
+	linux,rs485-enabled-at-boot-time;
+	rs485-rx-during-tx;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usb_h1_vbus>;
+	status = "okay";
+};
+
+&usbh2 {
+	pinctrl-names = "idle", "active";
+	pinctrl-0 = <&pinctrl_usbh2_idle>;
+	pinctrl-1 = <&pinctrl_usbh2_active>;
+	vbus-supply = <&reg_usb_h2_vbus>;
+	status = "okay";
+};
+
+&usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	vbus-supply = <&reg_usb_otg_vbus>;
+	disable-over-current;
+	dr_mode = "otg";
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&usbphynop1 {
+	clocks = <&clks IMX6QDL_CLK_USBPHY1>;
+	clock-names = "main_clk";
+	vcc-supply = <&reg_usb_h1_vbus>;
+};
+
+&usbphynop2 {
+	vcc-supply = <&reg_usb_h2_vbus>;
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	wakeup-source;
+	voltage-ranges = <3300 3300>;
+	vmmc-supply = <&reg_sw4>;
+	fsl,wp-controller;
+	status = "okay";
+};
+
+&usdhc4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	bus-width = <8>;
+	non-removable;
+	no-1-8-v;
+	keep-power-in-suspend;
+	voltage-ranges = <3300 3300>;
+	vmmc-supply = <&reg_sw4>;
+	fsl,wp-controller;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog1>;
+	fsl,ext-reset-output;
+	timeout-sec = <10>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN	0x1b0b0
+			MX6QDL_PAD_ENET_REF_CLK__GPIO1_IO23	0x1b0b0	/* FEC INT */
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER	0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN	0x0001b098
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0	0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1	0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1	0x0001b098
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0	0x0001b098
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
+		>;
+	};
+
+	pinctrl_reset_gpio_led: reset-gpio-led-grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18		0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b810
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b810
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL  0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+		>;
+	};
+
+	pinctrl_lcd_enable: lcdenablegrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D23__GPIO3_IO23  0x1b0b0 /* lcd enable */
+			MX6QDL_PAD_EIM_D16__GPIO3_IO16  0x1b0b0 /* sel6_8 */
+		>;
+	};
+
+	pinctrl_lm75: lm75grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW0__GPIO4_IO07		0x1b0b0
+		>;
+	};
+
+	pinctrl_proximity: proximitygrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__GPIO4_IO11  0x1b0b0
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x0001b0b0
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT2__PWM2_OUT 0x0001b0b0
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT1__PWM3_OUT 0x0001b0b0
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x0001b0b0
+		>;
+	};
+
+	pinctrl_rtc: rtc-grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL1__GPIO4_IO08 0x1b0b0 /* RTC INT */
+		>;
+	};
+
+	pinctrl_ctouch: ctouch-grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x1b0b0 /* CTOUCH_INT */
+			MX6QDL_PAD_SD1_CLK__GPIO1_IO20 0x0001b0b0 /* CTOUCH_RESET */
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1
+			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1
+			MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x0001b0b0
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT4__UART2_RX_DATA 0x1b0b1
+			MX6QDL_PAD_SD3_DAT5__UART2_TX_DATA 0x1b0b1
+			MX6QDL_PAD_EIM_D28__UART2_CTS_B 0x1b0b1
+			MX6QDL_PAD_EIM_D29__UART2_RTS_B 0x1b0b1
+		>;
+	};
+
+	pinctrl_usbh2_idle: usbh2-idle-grp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_TXC__USB_H2_DATA      0x00013018
+			MX6QDL_PAD_RGMII_TX_CTL__USB_H2_STROBE 0x00013018
+		>;
+	};
+
+	pinctrl_usbh2_active: usbh2-active-grp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_TXC__USB_H2_DATA      0x00013018
+			MX6QDL_PAD_RGMII_TX_CTL__USB_H2_STROBE 0x00017018
+		>;
+	};
+
+	pinctrl_usb3503: usb3503-grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1    0x00000018
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12     0x1b0b0 /* USB INT */
+			MX6QDL_PAD_DISP0_DAT11__GPIO5_IO05 0x0001b0b0 /* USB Reset */
+			MX6QDL_PAD_SD1_DAT0__GPIO1_IO16    0x1b0b0 /* USB Connect */
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID	0x17059
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD    0x00017069
+			MX6QDL_PAD_SD2_CLK__SD2_CLK    0x00010038
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x00017069
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x00017069
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x00017069
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x00017069
+			MX6QDL_PAD_GPIO_4__SD2_CD_B    0x0001b0b0
+		>;
+	};
+
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD    0x00017059
+			MX6QDL_PAD_SD4_CLK__SD4_CLK    0x00010059
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x00017059
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x00017059
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x00017059
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x00017059
+			MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x00017059
+			MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x00017059
+			MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x00017059
+			MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x00017059
+		>;
+	};
+
+	pinctrl_wdog1: wdoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__WDOG1_B 0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6q-bx50v3.dtsi b/arch/arm/boot/dts/nxp/imx/imx6q-bx50v3.dtsi
index 10922375c51e..e1d0c6e123fd 100644
--- a/arch/arm/boot/dts/imx6q-bx50v3.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-bx50v3.dtsi
@@ -94,7 +94,7 @@
 		mdio-gpio0 = &mdio0;
 	};
 
-	mdio0: mdio-gpio {
+	mdio0: mdio {
 		compatible = "virtual,mdio-gpio";
 		gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>, /* mdc */
 			<&gpio2 7 GPIO_ACTIVE_HIGH>; /* mdio */
@@ -160,7 +160,7 @@
 	pinctrl-0 = <&pinctrl_ecspi5>;
 	status = "okay";
 
-	m25_eeprom: m25p80@0 {
+	m25_eeprom: eeprom@0 {
 		compatible = "atmel,at25";
 		spi-max-frequency = <10000000>;
 		size = <0x8000>;
@@ -228,6 +228,7 @@
 			sgtl5000: codec@a {
 				compatible = "fsl,sgtl5000";
 				reg = <0x0a>;
+				#sound-dai-cells = <0>;
 				clocks = <&mclk>;
 				VDDA-supply = <&reg_1p8v>;
 				VDDIO-supply = <&reg_3p3v>;
@@ -244,6 +245,7 @@
 				reg = <0x74>;
 				gpio-controller;
 				#gpio-cells = <2>;
+				#interrupt-cells = <2>;
 				interrupt-controller;
 				interrupt-parent = <&gpio2>;
 				interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
@@ -389,7 +391,6 @@
 
 		#address-cells = <3>;
 		#size-cells = <2>;
-		#interrupt-cells = <1>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx6q-cm-fx6.dts b/arch/arm/boot/dts/nxp/imx/imx6q-cm-fx6.dts
index bfb530f29d9d..299106fbe51c 100644
--- a/arch/arm/boot/dts/imx6q-cm-fx6.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-cm-fx6.dts
@@ -127,12 +127,21 @@
 		};
 	};
 
+	spdif_out: spdif-out {
+		compatible = "linux,spdif-dit";
+		#sound-dai-cells = <0>;
+	};
+
+	spdif_in: spdif-in {
+		compatible = "linux,spdif-dir";
+		#sound-dai-cells = <0>;
+	};
+
 	sound-spdif {
 		compatible = "fsl,imx-audio-spdif";
 		model = "imx-spdif";
-		spdif-controller = <&spdif>;
-		spdif-out;
-		spdif-in;
+		audio-cpu = <&spdif>;
+		audio-codec = <&spdif_out>, <&spdif_in>;
 	};
 };
 
@@ -141,7 +150,7 @@
 	pinctrl-0 = <&pinctrl_audmux>;
 	status = "okay";
 
-	ssi2 {
+	mux-ssi2 {
 		fsl,audmux-port = <1>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_RCLKDIR |
@@ -152,7 +161,7 @@
 		>;
 	};
 
-	audmux4 {
+	mux-audmux4 {
 		fsl,audmux-port = <3>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_TFSDIR |
@@ -260,10 +269,10 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	m25p80@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "st,m25p", "jedec,spi-nor";
+		compatible = "jedec,spi-nor";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
 	};
diff --git a/arch/arm/boot/dts/imx6q-cubox-i-emmc-som-v15.dts b/arch/arm/boot/dts/nxp/imx/imx6q-cubox-i-emmc-som-v15.dts
index 3e59ebbb3608..3e59ebbb3608 100644
--- a/arch/arm/boot/dts/imx6q-cubox-i-emmc-som-v15.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-cubox-i-emmc-som-v15.dts
diff --git a/arch/arm/boot/dts/imx6q-cubox-i-som-v15.dts b/arch/arm/boot/dts/nxp/imx/imx6q-cubox-i-som-v15.dts
index dab70d1230a2..dab70d1230a2 100644
--- a/arch/arm/boot/dts/imx6q-cubox-i-som-v15.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-cubox-i-som-v15.dts
diff --git a/arch/arm/boot/dts/imx6q-cubox-i.dts b/arch/arm/boot/dts/nxp/imx/imx6q-cubox-i.dts
index 1c7b262e3709..1c7b262e3709 100644
--- a/arch/arm/boot/dts/imx6q-cubox-i.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-cubox-i.dts
diff --git a/arch/arm/boot/dts/imx6q-dfi-fs700-m60.dts b/arch/arm/boot/dts/nxp/imx/imx6q-dfi-fs700-m60.dts
index 8bfe6337cd65..8bfe6337cd65 100644
--- a/arch/arm/boot/dts/imx6q-dfi-fs700-m60.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-dfi-fs700-m60.dts
diff --git a/arch/arm/boot/dts/imx6q-dhcom-pdk2.dts b/arch/arm/boot/dts/nxp/imx/imx6q-dhcom-pdk2.dts
index d4d57370615d..6efd7e9fc1b1 100644
--- a/arch/arm/boot/dts/imx6q-dhcom-pdk2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-dhcom-pdk2.dts
@@ -4,7 +4,7 @@
  * Copyright (C) 2018 Marek Vasut <marex@denx.de>
  *
  * DHCOM iMX6 variant:
- * DHCM-iMX6Q-C0800-R102-F0819-E-SD-RTC-T-HS-I-01D2
+ * DHCM-iMX6Q-C080-R102-F0819-E-SD-RTC-T-HS-I-01D2
  * DHCOM PCB number: 493-300 or newer
  * PDK2 PCB number: 516-400 or newer
  */
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-display5-tianma-tm070-1280x768.dts b/arch/arm/boot/dts/nxp/imx/imx6q-display5-tianma-tm070-1280x768.dts
new file mode 100644
index 000000000000..059750270fc4
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-display5-tianma-tm070-1280x768.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2017
+ * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
+ */
+
+/dts-v1/;
+
+#include "imx6q-display5.dtsi"
+
+&panel {
+	compatible = "tianma,tm070jdhg30";
+};
+
+&ldb {
+	lvds0: lvds-channel@0 {
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <18>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6q-display5.dtsi b/arch/arm/boot/dts/nxp/imx/imx6q-display5.dtsi
index fef5d7254536..4e448b4810f2 100644
--- a/arch/arm/boot/dts/imx6q-display5.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-display5.dtsi
@@ -1,38 +1,7 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
 /*
  * Copyright 2017
  * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is licensed under the terms of the GNU General Public
- *     License version 2.  This program is licensed "as is" without
- *     any warranty of any kind, whether express or implied.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 /dts-v1/;
@@ -147,7 +116,7 @@
 	pinctrl-0 = <&pinctrl_audmux>;
 	status = "okay";
 
-	ssi2 {
+	mux-ssi2 {
 		fsl,audmux-port = <1>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_SYN |
@@ -159,7 +128,7 @@
 		>;
 	};
 
-	aud6 {
+	mux-aud6 {
 		fsl,audmux-port = <5>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_RFSEL(8) |
@@ -276,7 +245,7 @@
 	pinctrl-0 = <&pinctrl_i2c3>;
 	status = "okay";
 
-	at24@50 {
+	eeprom@50 {
 		compatible = "atmel,24c256";
 		pagesize = <64>;
 		reg = <0x50>;
diff --git a/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts b/arch/arm/boot/dts/nxp/imx/imx6q-dmo-edmqmx6.dts
index c713ac03b3b9..17fabff80e90 100644
--- a/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-dmo-edmqmx6.dts
@@ -28,40 +28,31 @@
 		reg = <0x10000000 0x80000000>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 
-		reg_usb_otg_switch: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "usb_otg_switch";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio7 12 0>;
-			regulator-boot-on;
-			regulator-always-on;
-		};
+	reg_usb_otg_switch: regulator-usb-otg-switch {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_switch";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio7 12 0>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
 
-		reg_usb_host1: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "usb_host1_en";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio3 31 0>;
-			enable-active-high;
-		};
+	reg_usb_host1: regulator-usb-host1 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_host1_en";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 31 0>;
+		enable-active-high;
 	};
 
 	gpio-leds {
@@ -102,7 +93,7 @@
 	cs-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "m25p80", "jedec,spi-nor";
 		spi-max-frequency = <40000000>;
 		reg = <0>;
@@ -134,7 +125,7 @@
 		     &pinctrl_pfuze>;
 	status = "okay";
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
 		reg = <0x08>;
 		interrupt-parent = <&gpio3>;
@@ -275,7 +266,7 @@
 		reg = <0x4d>;
 	};
 
-	rtc: m41t62@68 {
+	rtc: rtc@68 {
 		compatible = "st,m41t62";
 		reg = <0x68>;
 	};
@@ -292,138 +283,136 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hog>;
 
-	imx6q-dmo-edmqmx6 {
-		pinctrl_hog: hoggrp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x80000000
-				MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x80000000
-			>;
-		};
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x80000000
+			MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x80000000
+		>;
+	};
 
-		pinctrl_can1: can1grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX	0x1b0b0
-				MX6QDL_PAD_GPIO_7__FLEXCAN1_TX		0x1b0b0
-			>;
-		};
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX	0x1b0b0
+			MX6QDL_PAD_GPIO_7__FLEXCAN1_TX		0x1b0b0
+		>;
+	};
 
-		pinctrl_ecspi5: ecspi5rp-1 {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_DAT0__ECSPI5_MISO	0x80000000
-				MX6QDL_PAD_SD1_CMD__ECSPI5_MOSI		0x80000000
-				MX6QDL_PAD_SD1_CLK__ECSPI5_SCLK		0x80000000
-				MX6QDL_PAD_SD2_DAT3__GPIO1_IO12		0x80000000
-			>;
-		};
+	pinctrl_ecspi5: ecspi5rp-1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT0__ECSPI5_MISO	0x80000000
+			MX6QDL_PAD_SD1_CMD__ECSPI5_MOSI		0x80000000
+			MX6QDL_PAD_SD1_CLK__ECSPI5_SCLK		0x80000000
+			MX6QDL_PAD_SD2_DAT3__GPIO1_IO12		0x80000000
+		>;
+	};
 
-		pinctrl_enet: enetgrp {
-			fsl,pins = <
-				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
-				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
-				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
-				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
-				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
-				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
-				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
-				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
-				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
-				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
-				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
-				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
-				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
-				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
-				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
-				MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25	0x1b0b0
-				MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
-			>;
-		};
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25	0x1b0b0
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
+		>;
+	};
 
-		pinctrl_i2c1: i2c1grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
-				MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
-			>;
-		};
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
+			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+		>;
+	};
 
-		pinctrl_i2c2: i2c2grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_EB2__I2C2_SCL		0x4001b8b1
-				MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
-			>;
-		};
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_EB2__I2C2_SCL		0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
+		>;
+	};
 
-		pinctrl_i2c3: i2c3grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D17__I2C3_SCL		0x4001b8b1
-				MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
-			>;
-		};
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__I2C3_SCL		0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
+		>;
+	};
 
-		pinctrl_pcie: pciegrp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL1__GPIO4_IO08		0x100b1
-			>;
-		};
+	pinctrl_pcie: pciegrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL1__GPIO4_IO08		0x100b1
+		>;
+	};
 
-		pinctrl_pfuze: pfuze100grp1 {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D20__GPIO3_IO20		0x80000000
-			>;
-		};
+	pinctrl_pfuze: pfuze100grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D20__GPIO3_IO20		0x80000000
+		>;
+	};
 
-		pinctrl_stmpe1: stmpe1grp {
-			fsl,pins = <MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x80000000>;
-		};
+	pinctrl_stmpe1: stmpe1grp {
+		fsl,pins = <MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x80000000>;
+	};
 
-		pinctrl_stmpe2: stmpe2grp {
-			fsl,pins = <MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x80000000>;
-		};
+	pinctrl_stmpe2: stmpe2grp {
+		fsl,pins = <MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x80000000>;
+	};
 
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
-				MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA	0x1b0b1
-			>;
-		};
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
+			MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA	0x1b0b1
+		>;
+	};
 
-		pinctrl_uart2: uart2grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D26__UART2_TX_DATA	0x1b0b1
-				MX6QDL_PAD_EIM_D27__UART2_RX_DATA	0x1b0b1
-			>;
-		};
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D26__UART2_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D27__UART2_RX_DATA	0x1b0b1
+		>;
+	};
 
-		pinctrl_usbotg: usbotggrp {
-			fsl,pins = <
-				MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x17059
-			>;
-		};
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x17059
+		>;
+	};
 
-		pinctrl_usdhc3: usdhc3grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
-				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
-				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
-				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
-				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
-				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
-			>;
-		};
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+		>;
+	};
 
-		pinctrl_usdhc4: usdhc4grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
-				MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
-				MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
-				MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
-				MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
-				MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059
-				MX6QDL_PAD_SD4_DAT4__SD4_DATA4		0x17059
-				MX6QDL_PAD_SD4_DAT5__SD4_DATA5		0x17059
-				MX6QDL_PAD_SD4_DAT6__SD4_DATA6		0x17059
-				MX6QDL_PAD_SD4_DAT7__SD4_DATA7		0x17059
-			>;
-		};
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
+			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059
+			MX6QDL_PAD_SD4_DAT4__SD4_DATA4		0x17059
+			MX6QDL_PAD_SD4_DAT5__SD4_DATA5		0x17059
+			MX6QDL_PAD_SD4_DAT6__SD4_DATA6		0x17059
+			MX6QDL_PAD_SD4_DAT7__SD4_DATA7		0x17059
+		>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx6q-dms-ba16.dts b/arch/arm/boot/dts/nxp/imx/imx6q-dms-ba16.dts
index 48fb47e715f6..484a60892229 100644
--- a/arch/arm/boot/dts/imx6q-dms-ba16.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-dms-ba16.dts
@@ -47,7 +47,7 @@
 	pinctrl-0 = <&pinctrl_ecspi5>;
 	status = "okay";
 
-	m25_eeprom: m25p80@0 {
+	m25_eeprom: eeprom@0 {
 		compatible = "atmel,at25256B", "atmel,at25";
 		spi-max-frequency = <20000000>;
 		size = <0x8000>;
@@ -96,6 +96,7 @@
 	sgtl5000: codec@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&sys_mclk>;
 		lrclk-strength = <0x3>;
 		VDDA-supply = <&reg_1p8v>;
diff --git a/arch/arm/boot/dts/imx6q-ds.dts b/arch/arm/boot/dts/nxp/imx/imx6q-ds.dts
index b0a63a133977..b0a63a133977 100644
--- a/arch/arm/boot/dts/imx6q-ds.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-ds.dts
diff --git a/arch/arm/boot/dts/imx6q-emcon-avari.dts b/arch/arm/boot/dts/nxp/imx/imx6q-emcon-avari.dts
index 0f582a9d4c0e..02813368a820 100644
--- a/arch/arm/boot/dts/imx6q-emcon-avari.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-emcon-avari.dts
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: (GPL-2.0 or MIT)
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
 //
 // Copyright (C) 2018 emtrion GmbH
 //
diff --git a/arch/arm/boot/dts/imx6q-evi.dts b/arch/arm/boot/dts/nxp/imx/imx6q-evi.dts
index c63f371ede8b..78d941fef5df 100644
--- a/arch/arm/boot/dts/imx6q-evi.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-evi.dts
@@ -146,6 +146,7 @@
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
 	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-gk802.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gk802.dts
new file mode 100644
index 000000000000..e0d29b07fbb1
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gk802.dts
@@ -0,0 +1,165 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2013 Philipp Zabel
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "imx6q.dtsi"
+
+/ {
+	model = "Zealz GK802";
+	compatible = "zealz,imx6q-gk802", "fsl,imx6q";
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x40000000>;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		recovery-button {
+			label = "recovery";
+			gpios = <&gpio3 16 1>;
+			linux,code = <KEY_RESTART>;
+			wakeup-source;
+		};
+	};
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c3>;
+	status = "okay";
+};
+
+/* Internal I2C */
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	/* SDMC DM2016 1024 bit EEPROM + 128 bit OTP */
+	eeprom: dm2016@51 {
+		compatible = "sdmc,dm2016";
+		reg = <0x51>;
+	};
+};
+
+/* External I2C via HDMI */
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			/* Recovery button, active-low */
+			MX6QDL_PAD_EIM_D16__GPIO3_IO16  0x100b1
+			/* RTL8192CU enable GPIO, active-low */
+			MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL		0x4001b8b1
+			MX6QDL_PAD_GPIO_16__I2C3_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA	0x1b0b1
+			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+		>;
+	};
+
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
+			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059
+		>;
+	};
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+/* External USB-A port (USBOTG) */
+&usbotg {
+	disable-over-current;
+	status = "okay";
+};
+
+/* Internal USB port (USBH1), connected to RTL8192CU */
+&usbh1 {
+	disable-over-current;
+	status = "okay";
+};
+
+/* External microSD */
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	bus-width = <4>;
+	cd-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+};
+
+/* Internal microSD */
+&usdhc4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6q-gw51xx.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw51xx.dts
index f80173458e3f..f80173458e3f 100644
--- a/arch/arm/boot/dts/imx6q-gw51xx.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw51xx.dts
diff --git a/arch/arm/boot/dts/imx6q-gw52xx.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw52xx.dts
index 6e1c493c9c8c..6e1c493c9c8c 100644
--- a/arch/arm/boot/dts/imx6q-gw52xx.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw52xx.dts
diff --git a/arch/arm/boot/dts/imx6q-gw53xx.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw53xx.dts
index f13df8e9c8c4..f13df8e9c8c4 100644
--- a/arch/arm/boot/dts/imx6q-gw53xx.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw53xx.dts
diff --git a/arch/arm/boot/dts/imx6q-gw5400-a.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw5400-a.dts
index 4cde45d5c90c..bf8fde9cb38d 100644
--- a/arch/arm/boot/dts/imx6q-gw5400-a.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw5400-a.dts
@@ -34,20 +34,20 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* 102 -> MX6_PANLEDG */
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 
-		led1: user2 {
+		led1: led-user2 {
 			label = "user2";
 			gpios = <&gpio4 10 GPIO_ACTIVE_HIGH>; /* 106 -> MX6_PANLEDR */
 			default-state = "off";
 		};
 
-		led2: user3 {
+		led2: led-user3 {
 			label = "user3";
 			gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* 111 -> MX6_LOCLED# */
 			default-state = "off";
@@ -67,47 +67,37 @@
 		status = "okay";
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_1p0v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "1P0V";
-			regulator-min-microvolt = <1000000>;
-			regulator-max-microvolt = <1000000>;
-			regulator-always-on;
-		};
+	reg_1p0v: regulator-1p0v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P0V";
+		regulator-min-microvolt = <1000000>;
+		regulator-max-microvolt = <1000000>;
+		regulator-always-on;
+	};
 
-		reg_3p3v: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 
-		reg_usb_h1_vbus: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "usb_h1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-		};
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
 
-		reg_usb_otg_vbus: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
 	};
 
 	sound {
@@ -137,7 +127,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "sst,w25q256", "jedec,spi-nor";
 		spi-max-frequency = <30000000>;
 		reg = <0>;
@@ -194,7 +184,7 @@
 		#gpio-cells = <2>;
 	};
 
-	rtc: ds1672@68 {
+	rtc: rtc@68 {
 		compatible = "dallas,ds1672";
 		reg = <0x68>;
 	};
@@ -206,7 +196,7 @@
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
 		reg = <0x08>;
 
@@ -320,6 +310,7 @@
 	codec: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
 		VDDA-supply = <&sw4_reg>;
 		VDDIO-supply = <&reg_3p3v>;
diff --git a/arch/arm/boot/dts/imx6q-gw54xx.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw54xx.dts
index d5d46908cf6e..d5d46908cf6e 100644
--- a/arch/arm/boot/dts/imx6q-gw54xx.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw54xx.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-gw551x.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw551x.dts
new file mode 100644
index 000000000000..44d1871ac666
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw551x.dts
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2014 Gateworks Corporation
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-gw551x.dtsi"
+
+/ {
+	model = "Gateworks Ventana i.MX6 Dual/Quad GW551X";
+	compatible = "gw,imx6q-gw551x", "gw,ventana", "fsl,imx6q";
+};
diff --git a/arch/arm/boot/dts/imx6q-gw552x.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw552x.dts
index c973b7304225..c973b7304225 100644
--- a/arch/arm/boot/dts/imx6q-gw552x.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw552x.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-gw553x.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw553x.dts
new file mode 100644
index 000000000000..22842f2ef685
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw553x.dts
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2016 Gateworks Corporation
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-gw553x.dtsi"
+
+/ {
+	model = "Gateworks Ventana i.MX6 Dual/Quad GW553X";
+	compatible = "gw,imx6q-gw553x", "gw,ventana", "fsl,imx6q";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-gw560x.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw560x.dts
new file mode 100644
index 000000000000..c69fdd064e2f
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw560x.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2017 Gateworks Corporation
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-gw560x.dtsi"
+
+/ {
+	model = "Gateworks Ventana i.MX6 Dual/Quad GW560X";
+	compatible = "gw,imx6q-gw560x", "gw,ventana", "fsl,imx6q";
+};
+
+&sata {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-gw5903.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw5903.dts
new file mode 100644
index 000000000000..a9a33eeb9712
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw5903.dts
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2017 Gateworks Corporation
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-gw5903.dtsi"
+
+/ {
+	model = "Gateworks Ventana i.MX6 Dual/Quad GW5903";
+	compatible = "gw,imx6q-gw5903", "gw,ventana", "fsl,imx6q";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-gw5904.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw5904.dts
new file mode 100644
index 000000000000..25a93cd4e5f5
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw5904.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2017 Gateworks Corporation
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-gw5904.dtsi"
+
+/ {
+	model = "Gateworks Ventana i.MX6 Dual/Quad GW5904";
+	compatible = "gw,imx6q-gw5904", "gw,ventana", "fsl,imx6q";
+};
+
+&sata {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6q-gw5907.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw5907.dts
index b25526ef5886..b25526ef5886 100644
--- a/arch/arm/boot/dts/imx6q-gw5907.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw5907.dts
diff --git a/arch/arm/boot/dts/imx6q-gw5910.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw5910.dts
index 6aafa2fcee08..6aafa2fcee08 100644
--- a/arch/arm/boot/dts/imx6q-gw5910.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw5910.dts
diff --git a/arch/arm/boot/dts/imx6q-gw5912.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw5912.dts
index 4dcbd943cd93..4dcbd943cd93 100644
--- a/arch/arm/boot/dts/imx6q-gw5912.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw5912.dts
diff --git a/arch/arm/boot/dts/imx6q-gw5913.dts b/arch/arm/boot/dts/nxp/imx/imx6q-gw5913.dts
index 6f511f1665fd..6f511f1665fd 100644
--- a/arch/arm/boot/dts/imx6q-gw5913.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-gw5913.dts
diff --git a/arch/arm/boot/dts/imx6q-h100.dts b/arch/arm/boot/dts/nxp/imx/imx6q-h100.dts
index b8feadbff967..4c8ea4381559 100644
--- a/arch/arm/boot/dts/imx6q-h100.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-h100.dts
@@ -76,19 +76,19 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_h100_leds>;
 
-		led0: power {
+		led0: led-power {
 			label = "power";
 			gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
 			default-state = "on";
 		};
 
-		led1: stream {
+		led1: led-stream {
 			label = "stream";
 			gpios = <&gpio2 29 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 		};
 
-		led2: rec {
+		led2: led-rec {
 			label = "rec";
 			gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
 			default-state = "off";
@@ -166,12 +166,12 @@
 	pinctrl-0 = <&pinctrl_h100_i2c1>;
 	status = "okay";
 
-	eeprom: 24c02@51 {
+	eeprom: eeprom@51 {
 		compatible = "microchip,24c02", "atmel,24c02";
 		reg = <0x51>;
 	};
 
-	rtc: pcf8523@68 {
+	rtc: rtc@68 {
 		compatible = "nxp,pcf8523";
 		reg = <0x68>;
 	};
@@ -179,6 +179,7 @@
 	sgtl5000: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_h100_sgtl5000>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
@@ -216,120 +217,118 @@
 };
 
 &iomuxc {
-	h100 {
-		pinctrl_h100_hdmi: h100-hdmi {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE	0x1f8b0
-			>;
-		};
+	pinctrl_h100_hdmi: h100-hdmigrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE	0x1f8b0
+		>;
+	};
 
-		pinctrl_h100_i2c1: h100-i2c1 {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
-				MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
-			>;
-		};
+	pinctrl_h100_i2c1: h100-i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
+			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+		>;
+	};
 
-		pinctrl_h100_i2c2: h100-i2c2 {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
-				MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
-			>;
-		};
+	pinctrl_h100_i2c2: h100-i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
+		>;
+	};
 
-		pinctrl_h100_leds: pinctrl-h100-leds {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_DA0__GPIO3_IO00		0x1b0b0
-				MX6QDL_PAD_EIM_EB1__GPIO2_IO29		0x1b0b0
-				MX6QDL_PAD_EIM_EB0__GPIO2_IO28		0x1b0b0
-			>;
-		};
+	pinctrl_h100_leds: pinctrl-h100-ledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_DA0__GPIO3_IO00		0x1b0b0
+			MX6QDL_PAD_EIM_EB1__GPIO2_IO29		0x1b0b0
+			MX6QDL_PAD_EIM_EB0__GPIO2_IO28		0x1b0b0
+		>;
+	};
 
-		pinctrl_h100_reg_hdmi: h100-reg-hdmi {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_A18__GPIO2_IO20		0x1b0b0
-			>;
-		};
+	pinctrl_h100_reg_hdmi: h100-reg-hdmigrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A18__GPIO2_IO20		0x1b0b0
+		>;
+	};
 
-		pinctrl_h100_sgtl5000: h100-sgtl5000 {
-			fsl,pins = <
-				MX6QDL_PAD_DISP0_DAT19__AUD5_RXD	0x130b0
-				MX6QDL_PAD_KEY_COL0__AUD5_TXC		0x130b0
-				MX6QDL_PAD_KEY_ROW0__AUD5_TXD		0x110b0
-				MX6QDL_PAD_KEY_COL1__AUD5_TXFS		0x130b0
-				MX6QDL_PAD_GPIO_5__CCM_CLKO1		0x130b0
-			>;
-		};
+	pinctrl_h100_sgtl5000: h100-sgtl5000grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT19__AUD5_RXD	0x130b0
+			MX6QDL_PAD_KEY_COL0__AUD5_TXC		0x130b0
+			MX6QDL_PAD_KEY_ROW0__AUD5_TXD		0x110b0
+			MX6QDL_PAD_KEY_COL1__AUD5_TXFS		0x130b0
+			MX6QDL_PAD_GPIO_5__CCM_CLKO1		0x130b0
+		>;
+	};
 
-		pinctrl_h100_tc358743: h100-tc358743 {
-			fsl,pins = <
-				MX6QDL_PAD_NANDF_CS2__GPIO6_IO15	0x1b0b0
-			>;
-		};
+	pinctrl_h100_tc358743: h100-tc358743grp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CS2__GPIO6_IO15	0x1b0b0
+		>;
+	};
 
-		pinctrl_h100_uart2: h100-uart2 {
-			fsl,pins = <
-				MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA	0x1b0b1
-				MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA	0x1b0b1
-			>;
-		};
+	pinctrl_h100_uart2: h100-uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA	0x1b0b1
+			MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA	0x1b0b1
+		>;
+	};
 
-		pinctrl_h100_usbh1_vbus: hummingboard-usbh1-vbus {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_0__GPIO1_IO00		0x1b0b0
-			>;
-		};
+	pinctrl_h100_usbh1_vbus: hummingboard-usbh1-vbusgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_0__GPIO1_IO00		0x1b0b0
+		>;
+	};
 
-		pinctrl_h100_usbotg_id: hummingboard-usbotg-id {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x13059
-			>;
-		};
+	pinctrl_h100_usbotg_id: hummingboard-usbotg-idgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x13059
+		>;
+	};
 
-		pinctrl_h100_usbotg_vbus: hummingboard-usbotg-vbus {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x1b0b0
-			>;
-		};
+	pinctrl_h100_usbotg_vbus: hummingboard-usbotg-vbusgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x1b0b0
+		>;
+	};
 
-		pinctrl_h100_usdhc2: h100-usdhc2 {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1f071
-				MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
-				MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
-				MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
-				MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
-				MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
-				MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x13059
-				MX6QDL_PAD_KEY_ROW1__SD2_VSELECT	0x1b0b0
-			>;
-		};
+	pinctrl_h100_usdhc2: h100-usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1f071
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x13059
+			MX6QDL_PAD_KEY_ROW1__SD2_VSELECT	0x1b0b0
+		>;
+	};
 
-		pinctrl_h100_usdhc2_100mhz: h100-usdhc2-100mhz {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1f071
-				MX6QDL_PAD_SD2_CMD__SD2_CMD		0x170b9
-				MX6QDL_PAD_SD2_CLK__SD2_CLK		0x100b9
-				MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x170b9
-				MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x170b9
-				MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x170b9
-				MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x170b9
-				MX6QDL_PAD_KEY_ROW1__SD2_VSELECT	0x1b0b0
-			>;
-		};
+	pinctrl_h100_usdhc2_100mhz: h100-usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1f071
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x170b9
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x100b9
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x170b9
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x170b9
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x170b9
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x170b9
+			MX6QDL_PAD_KEY_ROW1__SD2_VSELECT	0x1b0b0
+		>;
+	};
 
-		pinctrl_h100_usdhc2_200mhz: h100-usdhc2-200mhz {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1f071
-				MX6QDL_PAD_SD2_CMD__SD2_CMD		0x170f9
-				MX6QDL_PAD_SD2_CLK__SD2_CLK		0x100f9
-				MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x170f9
-				MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x170f9
-				MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x170f9
-				MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x170f9
-				MX6QDL_PAD_KEY_ROW1__SD2_VSELECT	0x1b0b0
-			>;
-		};
+	pinctrl_h100_usdhc2_200mhz: h100-usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1f071
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x170f9
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x100f9
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x170f9
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x170f9
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x170f9
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x170f9
+			MX6QDL_PAD_KEY_ROW1__SD2_VSELECT	0x1b0b0
+		>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx6q-hummingboard-emmc-som-v15.dts b/arch/arm/boot/dts/nxp/imx/imx6q-hummingboard-emmc-som-v15.dts
index c51b4e4fd71e..c51b4e4fd71e 100644
--- a/arch/arm/boot/dts/imx6q-hummingboard-emmc-som-v15.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-hummingboard-emmc-som-v15.dts
diff --git a/arch/arm/boot/dts/imx6q-hummingboard-som-v15.dts b/arch/arm/boot/dts/nxp/imx/imx6q-hummingboard-som-v15.dts
index e4132d62ffa2..e4132d62ffa2 100644
--- a/arch/arm/boot/dts/imx6q-hummingboard-som-v15.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-hummingboard-som-v15.dts
diff --git a/arch/arm/boot/dts/imx6q-hummingboard.dts b/arch/arm/boot/dts/nxp/imx/imx6q-hummingboard.dts
index 8c9e94e648a7..8c9e94e648a7 100644
--- a/arch/arm/boot/dts/imx6q-hummingboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-hummingboard.dts
diff --git a/arch/arm/boot/dts/imx6q-hummingboard2-emmc-som-v15.dts b/arch/arm/boot/dts/nxp/imx/imx6q-hummingboard2-emmc-som-v15.dts
index 1998ebfa0fe0..1998ebfa0fe0 100644
--- a/arch/arm/boot/dts/imx6q-hummingboard2-emmc-som-v15.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-hummingboard2-emmc-som-v15.dts
diff --git a/arch/arm/boot/dts/imx6q-hummingboard2-som-v15.dts b/arch/arm/boot/dts/nxp/imx/imx6q-hummingboard2-som-v15.dts
index d3ad7329cd6d..d3ad7329cd6d 100644
--- a/arch/arm/boot/dts/imx6q-hummingboard2-som-v15.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-hummingboard2-som-v15.dts
diff --git a/arch/arm/boot/dts/imx6q-hummingboard2.dts b/arch/arm/boot/dts/nxp/imx/imx6q-hummingboard2.dts
index 5249f53dcdbc..5249f53dcdbc 100644
--- a/arch/arm/boot/dts/imx6q-hummingboard2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-hummingboard2.dts
diff --git a/arch/arm/boot/dts/imx6q-icore-mipi.dts b/arch/arm/boot/dts/nxp/imx/imx6q-icore-mipi.dts
index d51745268dbf..d51745268dbf 100644
--- a/arch/arm/boot/dts/imx6q-icore-mipi.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-icore-mipi.dts
diff --git a/arch/arm/boot/dts/imx6q-icore-ofcap10.dts b/arch/arm/boot/dts/nxp/imx/imx6q-icore-ofcap10.dts
index 02aca1e28ce3..02aca1e28ce3 100644
--- a/arch/arm/boot/dts/imx6q-icore-ofcap10.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-icore-ofcap10.dts
diff --git a/arch/arm/boot/dts/imx6q-icore-ofcap12.dts b/arch/arm/boot/dts/nxp/imx/imx6q-icore-ofcap12.dts
index 241811c52b62..241811c52b62 100644
--- a/arch/arm/boot/dts/imx6q-icore-ofcap12.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-icore-ofcap12.dts
diff --git a/arch/arm/boot/dts/imx6q-icore-rqs.dts b/arch/arm/boot/dts/nxp/imx/imx6q-icore-rqs.dts
index cf6ba724f497..cf6ba724f497 100644
--- a/arch/arm/boot/dts/imx6q-icore-rqs.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-icore-rqs.dts
diff --git a/arch/arm/boot/dts/imx6q-icore.dts b/arch/arm/boot/dts/nxp/imx/imx6q-icore.dts
index fe28c3cf54c0..fe28c3cf54c0 100644
--- a/arch/arm/boot/dts/imx6q-icore.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-icore.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-kontron-samx6i-ads2.dts b/arch/arm/boot/dts/nxp/imx/imx6q-kontron-samx6i-ads2.dts
new file mode 100644
index 000000000000..94c395cc020e
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-kontron-samx6i-ads2.dts
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: GPL-2.0 OR X11
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6qdl-kontron-samx6i.dtsi"
+#include "imx6qdl-kontron-samx6i-ads2.dtsi"
+
+/ {
+	model = "Kontron SMARC-sAMX6i Quad/Dual on SMARC Eval 2.0 carrier";
+	compatible = "kontron,imx6q-samx6i-ads2", "kontron,imx6q-samx6i", "fsl,imx6q";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-kontron-samx6i.dtsi b/arch/arm/boot/dts/nxp/imx/imx6q-kontron-samx6i.dtsi
new file mode 100644
index 000000000000..e76963436079
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-kontron-samx6i.dtsi
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: GPL-2.0 OR X11
+/*
+ * Copyright 2019 (C) Pengutronix, Marco Felsch <kernel@pengutronix.de>
+ */
+
+#include "imx6q.dtsi"
+#include "imx6qdl-kontron-samx6i.dtsi"
+
+/ {
+	model = "Kontron SMARC-sAMX6i Quad/Dual";
+	compatible = "kontron,imx6q-samx6i", "fsl,imx6q";
+};
diff --git a/arch/arm/boot/dts/imx6q-kp-tpc.dts b/arch/arm/boot/dts/nxp/imx/imx6q-kp-tpc.dts
index 50fbf46d17c2..50fbf46d17c2 100644
--- a/arch/arm/boot/dts/imx6q-kp-tpc.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-kp-tpc.dts
diff --git a/arch/arm/boot/dts/imx6q-kp.dtsi b/arch/arm/boot/dts/nxp/imx/imx6q-kp.dtsi
index 1ade0bff681d..d6deb8c22b8c 100644
--- a/arch/arm/boot/dts/imx6q-kp.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-kp.dtsi
@@ -15,7 +15,7 @@
 / {
 	backlight_lcd: backlight-lcd {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 255>;
 		num-interpolated-steps = <255>;
 		default-brightness-level = <250>;
@@ -23,7 +23,7 @@
 
 	beeper {
 		compatible = "pwm-beeper";
-		pwms = <&pwm2 0 500000>;
+		pwms = <&pwm2 0 500000 0>;
 	};
 
 	lcd_display: display {
@@ -66,17 +66,17 @@
 	leds {
 		compatible = "gpio-leds";
 
-		green {
+		led-green {
 			label = "led1";
 			gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "gpio";
+			linux,default-trigger = "none";
 			default-state = "off";
 		};
 
-		red {
+		led-red {
 			label = "led0";
 			gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "gpio";
+			linux,default-trigger = "none";
 			default-state = "off";
 		};
 	};
@@ -135,7 +135,7 @@
 	pinctrl-0 = <&pinctrl_audmux>;
 	status = "okay";
 
-	ssi1 {
+	mux-ssi1 {
 		fsl,audmux-port = <0>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_SYN |
@@ -147,7 +147,7 @@
 		>;
 	};
 
-	aud3 {
+	mux-aud3 {
 		fsl,audmux-port = <2>;
 		fsl,port-config = <
 			IMX_AUDMUX_V2_PTCR_SYN
@@ -378,14 +378,12 @@
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
 };
 
 &pwm2 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm2>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6q-logicpd.dts b/arch/arm/boot/dts/nxp/imx/imx6q-logicpd.dts
index 46a4ddedb423..86b813a57c1e 100644
--- a/arch/arm/boot/dts/imx6q-logicpd.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-logicpd.dts
@@ -110,13 +110,13 @@
 };
 
 &iomuxc {
-	pinctrl_lcd_reg: lcdreg {
+	pinctrl_lcd_reg: lcdreggrp {
 		fsl,pins = <
 			MX6QDL_PAD_DI0_PIN15__GPIO4_IO17	0x100b0	/* R_LCD_PANEL_PWR */
 		>;
 	};
 
-	pinctrl_lcd_reset: lcdreset {
+	pinctrl_lcd_reset: lcdresetgrp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_A25__GPIO5_IO02	0x100b0	/* LCD_nRESET */
 		>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-lxr.dts b/arch/arm/boot/dts/nxp/imx/imx6q-lxr.dts
new file mode 100644
index 000000000000..ae4f8eeb105d
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-lxr.dts
@@ -0,0 +1,87 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+//
+// Copyright 2024 Comvetia AG
+
+/dts-v1/;
+#include "imx6q-phytec-pfla02.dtsi"
+
+/ {
+	model = "COMVETIA QSoIP LXR-2";
+	compatible = "comvetia,imx6q-lxr", "phytec,imx6q-pfla02", "fsl,imx6q";
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	spi {
+		compatible = "spi-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_spi_gpio>;
+		sck-gpios = <&gpio5 8 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio5 7 GPIO_ACTIVE_HIGH>;
+		num-chipselects = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fpga@0 {
+			compatible = "altr,fpga-passive-serial";
+			reg = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_fpga>;
+			nconfig-gpios = <&gpio4 18 GPIO_ACTIVE_LOW>;
+			nstat-gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
+			confd-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&ecspi3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3>;
+	cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&fec {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&usdhc3 {
+	no-1-8-v;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_fpga: fpgagrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_6__GPIO1_IO06       0x1b0b0
+			MX6QDL_PAD_DI0_PIN2__GPIO4_IO18     0x1b0b0
+			MX6QDL_PAD_DI0_PIN3__GPIO4_IO19     0x1b0b0
+		>;
+	};
+
+	pinctrl_spi_gpio: spigpiogrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT14__GPIO5_IO08  0x1b0b0
+			MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07  0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6q-marsboard.dts b/arch/arm/boot/dts/nxp/imx/imx6q-marsboard.dts
index 05ee28388229..2c9961333b0a 100644
--- a/arch/arm/boot/dts/imx6q-marsboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-marsboard.dts
@@ -73,14 +73,14 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_led>;
 
-		user1 {
+		led-user1 {
 			label = "imx6:green:user1";
 			gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 			linux,default-trigger = "heartbeat";
 		};
 
-		user2 {
+		led-user2 {
 			label = "imx6:green:user2";
 			gpios = <&gpio3 28 GPIO_ACTIVE_LOW>;
 			default-state = "off";
@@ -100,7 +100,7 @@
 	cs-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
-	m25p80@0 {
+	flash@0 {
 		compatible = "microchip,sst25vf016b";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/imx6q-mba6.dtsi b/arch/arm/boot/dts/nxp/imx/imx6q-mba6.dtsi
index 0d7be4567291..1e5eb837fd80 100644
--- a/arch/arm/boot/dts/imx6q-mba6.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-mba6.dtsi
@@ -32,7 +32,7 @@
 };
 
 &iomuxc {
-	pinctrl_ecspi5_mba6x: ecspi5grp-mba6x {
+	pinctrl_ecspi5_mba6x: ecspi5-mba6xgrp {
 		fsl,pins = <
 			/* HYS, SPEED = MED, 100k up, DSE = 011, SRE_FAST */
 			MX6QDL_PAD_SD1_DAT0__ECSPI5_MISO 0x1b099
diff --git a/arch/arm/boot/dts/imx6q-mba6a.dts b/arch/arm/boot/dts/nxp/imx/imx6q-mba6a.dts
index 349a08605a5e..349a08605a5e 100644
--- a/arch/arm/boot/dts/imx6q-mba6a.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-mba6a.dts
diff --git a/arch/arm/boot/dts/imx6q-mba6b.dts b/arch/arm/boot/dts/nxp/imx/imx6q-mba6b.dts
index 02c9f3e91b8f..02c9f3e91b8f 100644
--- a/arch/arm/boot/dts/imx6q-mba6b.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-mba6b.dts
diff --git a/arch/arm/boot/dts/imx6q-mccmon6.dts b/arch/arm/boot/dts/nxp/imx/imx6q-mccmon6.dts
index 55692c73943d..ef5c0eda8b15 100644
--- a/arch/arm/boot/dts/imx6q-mccmon6.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-mccmon6.dts
@@ -100,8 +100,10 @@
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
 	phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
+	fsl,err006687-workaround-present;
 	status = "okay";
 };
 
@@ -277,7 +279,7 @@
 	ranges = <0 0 0x08000000 0x08000000>;
 	status = "okay";
 
-	nor@0,0 {
+	flash@0,0 {
 		compatible = "cfi-flash";
 		reg = <0 0 0x02000000>;
 		#address-cells = <1>;
@@ -290,8 +292,6 @@
 };
 
 &iomuxc {
-	pinctrl-names = "default";
-
 	pinctrl_backlight: dispgrp {
 		fsl,pins = <
 			/* BLEN_OUT */
diff --git a/arch/arm/boot/dts/imx6q-nitrogen6_max.dts b/arch/arm/boot/dts/nxp/imx/imx6q-nitrogen6_max.dts
index 03bec0c53063..03bec0c53063 100644
--- a/arch/arm/boot/dts/imx6q-nitrogen6_max.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-nitrogen6_max.dts
diff --git a/arch/arm/boot/dts/imx6q-nitrogen6_som2.dts b/arch/arm/boot/dts/nxp/imx/imx6q-nitrogen6_som2.dts
index eb4eecb6ed22..eb4eecb6ed22 100644
--- a/arch/arm/boot/dts/imx6q-nitrogen6_som2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-nitrogen6_som2.dts
diff --git a/arch/arm/boot/dts/imx6q-nitrogen6x.dts b/arch/arm/boot/dts/nxp/imx/imx6q-nitrogen6x.dts
index 435445a34ad0..435445a34ad0 100644
--- a/arch/arm/boot/dts/imx6q-nitrogen6x.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-nitrogen6x.dts
diff --git a/arch/arm/boot/dts/imx6q-novena.dts b/arch/arm/boot/dts/nxp/imx/imx6q-novena.dts
index 225cf6b7a7a4..24fc3ff1c70c 100644
--- a/arch/arm/boot/dts/imx6q-novena.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-novena.dts
@@ -67,7 +67,7 @@
 
 	backlight: backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 10000000>;
+		pwms = <&pwm1 0 10000000 0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_backlight_novena>;
 		power-supply = <&reg_lvds_lcd>;
@@ -86,7 +86,7 @@
 			linux,code = <KEY_POWER>;
 		};
 
-		lid {
+		lid-event {
 			label = "Lid";
 			gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
 			linux,input-type = <5>;	/* EV_SW */
@@ -99,7 +99,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_leds_novena>;
 
-		heartbeat {
+		led-heartbeat {
 			label = "novena:white:panel";
 			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
@@ -265,7 +265,7 @@
 		reg = <0x1c>;
 	};
 
-	rtc: pcf8523@68 {
+	rtc: rtc@68 {
 		compatible = "nxp,pcf8523";
 		reg = <0x68>;
 	};
@@ -288,7 +288,7 @@
 		vio-supply = <&reg_3p3v>;
 		vcc-supply = <&reg_3p3v>;
 
-		stmpe_touchscreen {
+		touchscreen {
 			compatible = "st,stmpe-ts";
 			st,sample-time = <4>;
 			st,mod-12b = <1>;
@@ -308,7 +308,7 @@
 	pinctrl-0 = <&pinctrl_i2c2_novena>;
 	status = "okay";
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
 		reg = <0x08>;
 
@@ -465,7 +465,6 @@
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	status = "okay";
 };
 
@@ -531,7 +530,7 @@
 };
 
 &iomuxc {
-	pinctrl_audmux_novena: audmuxgrp-novena {
+	pinctrl_audmux_novena: audmux-novenagrp {
 		fsl,pins = <
 			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
 			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
@@ -540,7 +539,7 @@
 		>;
 	};
 
-	pinctrl_backlight_novena: backlightgrp-novena {
+	pinctrl_backlight_novena: backlight-novenagrp {
 		fsl,pins = <
 			MX6QDL_PAD_DISP0_DAT8__PWM1_OUT		0x1b0b0
 			MX6QDL_PAD_CSI0_DAT10__GPIO5_IO28	0x1b0b1
@@ -548,7 +547,7 @@
 		>;
 	};
 
-	pinctrl_ecspi3_novena: ecspi3grp-novena {
+	pinctrl_ecspi3_novena: ecspi3-novenagrp {
 		fsl,pins = <
 			MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO	0x100b1
 			MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI	0x100b1
@@ -556,7 +555,7 @@
 		>;
 	};
 
-	pinctrl_enet_novena: enetgrp-novena {
+	pinctrl_enet_novena: enet-novenagrp {
 		fsl,pins = <
 			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
 			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
@@ -579,7 +578,7 @@
 		>;
 	};
 
-	pinctrl_fpga_gpio: fpgagpiogrp-novena {
+	pinctrl_fpga_gpio: fpgagpio-novenagrp {
 		fsl,pins = <
 			/* FPGA power */
 			MX6QDL_PAD_SD1_DAT1__GPIO1_IO17		0x1b0b1
@@ -615,7 +614,7 @@
 		>;
 	};
 
-	pinctrl_fpga_eim: fpgaeimgrp-novena {
+	pinctrl_fpga_eim: fpgaeim-novenagrp {
 		fsl,pins = <
 			/* FPGA power */
 			MX6QDL_PAD_SD1_DAT1__GPIO1_IO17		0x1b0b1
@@ -651,7 +650,7 @@
 		>;
 	};
 
-	pinctrl_gpio_keys_novena: gpiokeysgrp-novena {
+	pinctrl_gpio_keys_novena: gpiokeys-novenagrp {
 		fsl,pins = <
 			/* User button */
 			MX6QDL_PAD_KEY_COL4__GPIO4_IO14		0x1b0b0
@@ -662,35 +661,35 @@
 		>;
 	};
 
-	pinctrl_hdmi_novena: hdmigrp-novena {
+	pinctrl_hdmi_novena: hdmi-novenagrp {
 		fsl,pins = <
 			MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE	0x1f8b0
 			MX6QDL_PAD_EIM_A24__GPIO5_IO04		0x1b0b1
 		>;
 	};
 
-	pinctrl_i2c1_novena: i2c1grp-novena {
+	pinctrl_i2c1_novena: i2c1-novenagrp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
 			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
 		>;
 	};
 
-	pinctrl_i2c2_novena: i2c2grp-novena {
+	pinctrl_i2c2_novena: i2c2-novenagrp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_EB2__I2C2_SCL		0x4001b8b1
 			MX6QDL_PAD_EIM_D16__I2C2_SDA		0x4001b8b1
 		>;
 	};
 
-	pinctrl_i2c3_novena: i2c3grp-novena {
+	pinctrl_i2c3_novena: i2c3-novenagrp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D17__I2C3_SCL		0x4001b8b1
 			MX6QDL_PAD_EIM_D18__I2C3_SDA		0x4001b8b1
 		>;
 	};
 
-	pinctrl_kpp_novena: kppgrp-novena {
+	pinctrl_kpp_novena: kpp-novenagrp {
 		fsl,pins = <
 			/* Front panel button */
 			MX6QDL_PAD_KEY_ROW1__KEY_ROW1		0x1b0b1
@@ -699,13 +698,13 @@
 		>;
 	};
 
-	pinctrl_leds_novena: ledsgrp-novena {
+	pinctrl_leds_novena: leds-novenagrp {
 		fsl,pins = <
 			MX6QDL_PAD_SD1_DAT3__GPIO1_IO21		0x1b0b1
 		>;
 	};
 
-	pinctrl_pcie_novena: pciegrp-novena {
+	pinctrl_pcie_novena: pcie-novenagrp {
 		fsl,pins = <
 			/* Reset */
 			MX6QDL_PAD_EIM_D29__GPIO3_IO29		0x1b0b1
@@ -716,13 +715,13 @@
 		>;
 	};
 
-	pinctrl_sata_novena: satagrp-novena {
+	pinctrl_sata_novena: sata-novenagrp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D30__GPIO3_IO30		0x1b0b1
 		>;
 	};
 
-	pinctrl_senoko_novena: senokogrp-novena {
+	pinctrl_senoko_novena: senoko-novenagrp {
 		fsl,pins = <
 			/* Senoko IRQ line */
 			MX6QDL_PAD_SD1_CLK__GPIO1_IO20		0x13048
@@ -731,7 +730,7 @@
 		>;
 	};
 
-	pinctrl_sound_novena: soundgrp-novena {
+	pinctrl_sound_novena: sound-novenagrp {
 		fsl,pins = <
 			/* Audio power regulator */
 			MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17	0x1b0b1
@@ -741,41 +740,41 @@
 		>;
 	};
 
-	pinctrl_stmpe_novena: stmpegrp-novena {
+	pinctrl_stmpe_novena: stmpe-novenagrp {
 		fsl,pins = <
 			/* Touchscreen interrupt */
 			MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13	0x1b0b1
 		>;
 	};
 
-	pinctrl_uart2_novena: uart2grp-novena {
+	pinctrl_uart2_novena: uart2-novenagrp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D26__UART2_TX_DATA	0x1b0b1
 			MX6QDL_PAD_EIM_D27__UART2_RX_DATA	0x1b0b1
 		>;
 	};
 
-	pinctrl_uart3_novena: uart3grp-novena {
+	pinctrl_uart3_novena: uart3-novenagrp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
 			MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
 		>;
 	};
 
-	pinctrl_uart4_novena: uart4grp-novena {
+	pinctrl_uart4_novena: uart4-novenagrp {
 		fsl,pins = <
 			MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA	0x1b0b1
 			MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA	0x1b0b1
 		>;
 	};
 
-	pinctrl_usbotg_novena: usbotggrp-novena {
+	pinctrl_usbotg_novena: usbotg-novenagrp {
 		fsl,pins = <
 			MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x17059
 		>;
 	};
 
-	pinctrl_usdhc2_novena: usdhc2grp-novena {
+	pinctrl_usdhc2_novena: usdhc2-novenagrp {
 		fsl,pins = <
 			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x170f9
 			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x100f9
@@ -790,7 +789,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_novena: usdhc3grp-novena {
+	pinctrl_usdhc3_novena: usdhc3-novenagrp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170f9
 			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100f9
diff --git a/arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts b/arch/arm/boot/dts/nxp/imx/imx6q-phytec-mira-rdk-emmc.dts
index 322f071d972f..322f071d972f 100644
--- a/arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-phytec-mira-rdk-emmc.dts
diff --git a/arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts b/arch/arm/boot/dts/nxp/imx/imx6q-phytec-mira-rdk-nand.dts
index 3f13726c8058..3f13726c8058 100644
--- a/arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-phytec-mira-rdk-nand.dts
diff --git a/arch/arm/boot/dts/imx6q-phytec-pbab01.dts b/arch/arm/boot/dts/nxp/imx/imx6q-phytec-pbab01.dts
index affe30b02d5a..affe30b02d5a 100644
--- a/arch/arm/boot/dts/imx6q-phytec-pbab01.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-phytec-pbab01.dts
diff --git a/arch/arm/boot/dts/imx6q-phytec-pfla02.dtsi b/arch/arm/boot/dts/nxp/imx/imx6q-phytec-pfla02.dtsi
index 500944bd2a05..500944bd2a05 100644
--- a/arch/arm/boot/dts/imx6q-phytec-pfla02.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-phytec-pfla02.dtsi
diff --git a/arch/arm/boot/dts/imx6q-pico-dwarf.dts b/arch/arm/boot/dts/nxp/imx/imx6q-pico-dwarf.dts
index 479a63ed42af..479a63ed42af 100644
--- a/arch/arm/boot/dts/imx6q-pico-dwarf.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-pico-dwarf.dts
diff --git a/arch/arm/boot/dts/imx6q-pico-hobbit.dts b/arch/arm/boot/dts/nxp/imx/imx6q-pico-hobbit.dts
index b767131068f5..b767131068f5 100644
--- a/arch/arm/boot/dts/imx6q-pico-hobbit.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-pico-hobbit.dts
diff --git a/arch/arm/boot/dts/imx6q-pico-nymph.dts b/arch/arm/boot/dts/nxp/imx/imx6q-pico-nymph.dts
index e8ad4c12b263..e8ad4c12b263 100644
--- a/arch/arm/boot/dts/imx6q-pico-nymph.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-pico-nymph.dts
diff --git a/arch/arm/boot/dts/imx6q-pico-pi.dts b/arch/arm/boot/dts/nxp/imx/imx6q-pico-pi.dts
index cc2394ddad6c..cc2394ddad6c 100644
--- a/arch/arm/boot/dts/imx6q-pico-pi.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-pico-pi.dts
diff --git a/arch/arm/boot/dts/imx6q-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx6q-pinfunc.h
index e40409d04b97..e40409d04b97 100644
--- a/arch/arm/boot/dts/imx6q-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-pinfunc.h
diff --git a/arch/arm/boot/dts/imx6q-pistachio.dts b/arch/arm/boot/dts/nxp/imx/imx6q-pistachio.dts
index 7a33e54cc0f1..56b77cc0af2b 100644
--- a/arch/arm/boot/dts/imx6q-pistachio.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-pistachio.dts
@@ -100,7 +100,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_keys>;
 
-		power {
+		key-power {
 			label = "Power Button";
 			gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
 			wakeup-source;
@@ -124,7 +124,7 @@
 
 	backlight_lvds: backlight-lvds {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 50000>;
+		pwms = <&pwm1 0 50000 0>;
 		brightness-levels = <
 			0  /*1  2  3  4  5  6*/  7  8  9
 			10 11 12 13 14 15 16 17 18 19
@@ -196,6 +196,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_i2c1_sgtl5000>;
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
 		VDDA-supply = <&reg_1p8v>;
 		VDDIO-supply = <&reg_1p8v>;
@@ -208,7 +209,7 @@
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
 		reg = <0x08>;
 
@@ -570,7 +571,6 @@
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
@@ -636,11 +636,11 @@
 };
 
 &usbphy1 {
-	fsl,tx-d-cal = <0x5>;
+	fsl,tx-d-cal = <79>;
 };
 
 &usbphy2 {
-	fsl,tx-d-cal = <0x5>;
+	fsl,tx-d-cal = <79>;
 };
 
 &usdhc1 {
diff --git a/arch/arm/boot/dts/imx6q-prti6q.dts b/arch/arm/boot/dts/nxp/imx/imx6q-prti6q.dts
index b4605edfd2ab..fb81bd8ba035 100644
--- a/arch/arm/boot/dts/imx6q-prti6q.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-prti6q.dts
@@ -22,7 +22,7 @@
 		compatible = "pwm-backlight";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_backlight>;
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 16 64 255>;
 		num-interpolated-steps = <16>;
 		default-brightness-level = <1>;
@@ -111,12 +111,21 @@
 		};
 	};
 
+	spdif_out: spdif-out {
+		compatible = "linux,spdif-dit";
+		#sound-dai-cells = <0>;
+	};
+
+	spdif_in: spdif-in {
+		compatible = "linux,spdif-dir";
+		#sound-dai-cells = <0>;
+	};
+
 	sound-spdif {
 		compatible = "fsl,imx-audio-spdif";
 		model = "imx-spdif";
-		spdif-controller = <&spdif>;
-		spdif-in;
-		spdif-out;
+		audio-cpu = <&spdif>;
+		audio-codec = <&spdif_out>, <&spdif_in>;
 	};
 };
 
@@ -292,7 +301,6 @@
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
@@ -359,13 +367,16 @@
 	keep-power-in-suspend;
 	status = "okay";
 
-	wifi {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wifi@2 {
 		compatible = "ti,wl1271";
+		reg = <2>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_wifi>;
 		interrupts-extended = <&gpio1 30 IRQ_TYPE_LEVEL_HIGH>;
-		ref-clock-frequency = "38400000";
-		tcxo-clock-frequency = "19200000";
+		ref-clock-frequency = <38400000>;
+		tcxo-clock-frequency = <19200000>;
 	};
 };
 
@@ -535,7 +546,7 @@
 		>;
 	};
 
-	pinctrl_wifi_npd: wifinpd {
+	pinctrl_wifi_npd: wifinpdgrp {
 		fsl,pins = <
 			MX6QDL_PAD_ENET_RXD1__GPIO1_IO26	0x1b8b0
 		>;
diff --git a/arch/arm/boot/dts/imx6q-prtwd2.dts b/arch/arm/boot/dts/nxp/imx/imx6q-prtwd2.dts
index 349959d38020..0e02e448db10 100644
--- a/arch/arm/boot/dts/imx6q-prtwd2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-prtwd2.dts
@@ -22,6 +22,13 @@
 		reg = <0x80000000 0x20000000>;
 	};
 
+	clk50m_phy: phy-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+		clock-output-names = "enet_ref_pad";
+	};
+
 	usdhc2_wifi_pwrseq: usdhc2_wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		pinctrl-names = "default";
@@ -49,13 +56,17 @@
 	status = "okay";
 };
 
+&clks {
+	clocks = <&clk50m_phy>;
+	clock-names = "enet_ref_pad";
+	assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&clk50m_phy>;
+};
+
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rmii";
-	clocks = <&clks IMX6QDL_CLK_ENET>,
-		 <&clks IMX6QDL_CLK_ENET>;
-	clock-names = "ipg", "ahb";
 	status = "okay";
 
 	fixed-link {
@@ -122,7 +133,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usb_eth_chg>;
 
-	pinctrl_can1phy: can1phy {
+	pinctrl_can1phy: can1phygrp {
 		fsl,pins = <
 			/* CAN1_SR */
 			MX6QDL_PAD_KEY_COL3__GPIO4_IO12	0x13070
@@ -145,9 +156,6 @@
 			MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22	0x1b0b0
 			/* nINTRP */
 			MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23	0x1b0b0
-
-			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x10030
-			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x10030
 		>;
 	};
 
@@ -179,7 +187,7 @@
 		>;
 	};
 
-	pinctrl_wifi_npd: wifinpd {
+	pinctrl_wifi_npd: wifinpdgrp {
 		fsl,pins = <
 			/* WL_REG_ON */
 			MX6QDL_PAD_NANDF_RB0__GPIO6_IO10	0x13069
diff --git a/arch/arm/boot/dts/imx6q-rex-pro.dts b/arch/arm/boot/dts/nxp/imx/imx6q-rex-pro.dts
index 1767e1a3cd53..271f4b2d9b9f 100644
--- a/arch/arm/boot/dts/imx6q-rex-pro.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-rex-pro.dts
@@ -19,7 +19,7 @@
 };
 
 &ecspi3 {
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "sst,sst25vf032b", "jedec,spi-nor";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/imx6q-sabreauto.dts b/arch/arm/boot/dts/nxp/imx/imx6q-sabreauto.dts
index 6e981a3e0a83..6e981a3e0a83 100644
--- a/arch/arm/boot/dts/imx6q-sabreauto.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-sabreauto.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-sabrelite.dts b/arch/arm/boot/dts/nxp/imx/imx6q-sabrelite.dts
new file mode 100644
index 000000000000..7c6a2f234ccb
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-sabrelite.dts
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: GPL-2.0 OR X11
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-sabrelite.dtsi"
+
+/ {
+	model = "Freescale i.MX6 Quad SABRE Lite Board";
+	compatible = "fsl,imx6q-sabrelite", "fsl,imx6q";
+};
+
+&sata {
+	status = "okay";
+};
+
+&ipu1_csi1_from_mipi_vc1 {
+	clock-lanes = <0>;
+	data-lanes = <1 2>;
+};
diff --git a/arch/arm/boot/dts/imx6q-sabresd.dts b/arch/arm/boot/dts/nxp/imx/imx6q-sabresd.dts
index eec944673c0b..eec944673c0b 100644
--- a/arch/arm/boot/dts/imx6q-sabresd.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-sabresd.dts
diff --git a/arch/arm/boot/dts/imx6q-savageboard.dts b/arch/arm/boot/dts/nxp/imx/imx6q-savageboard.dts
index 717ac62fc2cf..717ac62fc2cf 100644
--- a/arch/arm/boot/dts/imx6q-savageboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-savageboard.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-sbc6x.dts b/arch/arm/boot/dts/nxp/imx/imx6q-sbc6x.dts
new file mode 100644
index 000000000000..84fbcd129179
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-sbc6x.dts
@@ -0,0 +1,91 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Pavel Machek <pavel@denx.de>
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+
+/ {
+	model = "MicroSys sbc6x board";
+	compatible = "microsys,sbc6x", "fsl,imx6q";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x80000000>;
+	};
+};
+
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii";
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+		>;
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6q-skov-revc-lt2.dts b/arch/arm/boot/dts/nxp/imx/imx6q-skov-revc-lt2.dts
index ff97d22eb09f..ff97d22eb09f 100644
--- a/arch/arm/boot/dts/imx6q-skov-revc-lt2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-skov-revc-lt2.dts
diff --git a/arch/arm/boot/dts/imx6q-skov-revc-lt6.dts b/arch/arm/boot/dts/nxp/imx/imx6q-skov-revc-lt6.dts
index 3e3b36ad362a..3e3b36ad362a 100644
--- a/arch/arm/boot/dts/imx6q-skov-revc-lt6.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-skov-revc-lt6.dts
diff --git a/arch/arm/boot/dts/imx6q-skov-reve-mi1010ait-1cp1.dts b/arch/arm/boot/dts/nxp/imx/imx6q-skov-reve-mi1010ait-1cp1.dts
index 7f1f19b74bfa..0342a79ccd5d 100644
--- a/arch/arm/boot/dts/imx6q-skov-reve-mi1010ait-1cp1.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-skov-reve-mi1010ait-1cp1.dts
@@ -37,9 +37,9 @@
 
 &clks {
 	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
-			  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+			  <&clks IMX6QDL_CLK_LDB_DI1_SEL>, <&clks IMX6QDL_CLK_ENET_REF_SEL>;
 	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>,
-				 <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
+				 <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>, <&clk50m_phy>;
 };
 
 &hdmi {
@@ -125,3 +125,9 @@
 		>;
 	};
 };
+
+&reg_tft_vcom {
+	regulator-min-microvolt = <3160000>;
+	regulator-max-microvolt = <3160000>;
+	voltage-table = <3160000 73>;
+};
diff --git a/arch/arm/boot/dts/imx6q-solidsense.dts b/arch/arm/boot/dts/nxp/imx/imx6q-solidsense.dts
index 0e6a325df363..0e6a325df363 100644
--- a/arch/arm/boot/dts/imx6q-solidsense.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-solidsense.dts
diff --git a/arch/arm/boot/dts/imx6q-tbs2910.dts b/arch/arm/boot/dts/nxp/imx/imx6q-tbs2910.dts
index 8daef65d5bb3..5353a0c24420 100644
--- a/arch/arm/boot/dts/imx6q-tbs2910.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-tbs2910.dts
@@ -49,7 +49,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		blue {
+		led-blue {
 			label = "blue_status_led";
 			gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
@@ -90,11 +90,16 @@
 		ssi-controller = <&ssi1>;
 	};
 
+	spdif_out: spdif-out {
+		compatible = "linux,spdif-dit";
+		#sound-dai-cells = <0>;
+	};
+
 	sound-spdif {
 		compatible = "fsl,imx-audio-spdif";
 		model = "On-board SPDIF";
-		spdif-controller = <&spdif>;
-		spdif-out;
+		audio-cpu = <&spdif>;
+		audio-codec = <&spdif_out>;
 	};
 };
 
@@ -141,6 +146,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_sgtl5000>;
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_3p3v>;
 	};
diff --git a/arch/arm/boot/dts/imx6q-tqma6a.dtsi b/arch/arm/boot/dts/nxp/imx/imx6q-tqma6a.dtsi
index ab4c07c13a13..ab4c07c13a13 100644
--- a/arch/arm/boot/dts/imx6q-tqma6a.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-tqma6a.dtsi
diff --git a/arch/arm/boot/dts/imx6q-tqma6b.dtsi b/arch/arm/boot/dts/nxp/imx/imx6q-tqma6b.dtsi
index 7224c376c318..7224c376c318 100644
--- a/arch/arm/boot/dts/imx6q-tqma6b.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-tqma6b.dtsi
diff --git a/arch/arm/boot/dts/imx6q-ts4900.dts b/arch/arm/boot/dts/nxp/imx/imx6q-ts4900.dts
index dce1e8671ebe..dce1e8671ebe 100644
--- a/arch/arm/boot/dts/imx6q-ts4900.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-ts4900.dts
diff --git a/arch/arm/boot/dts/imx6q-ts7970.dts b/arch/arm/boot/dts/nxp/imx/imx6q-ts7970.dts
index 570bd3c309a6..570bd3c309a6 100644
--- a/arch/arm/boot/dts/imx6q-ts7970.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-ts7970.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1010-comtft.dts b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1010-comtft.dts
new file mode 100644
index 000000000000..d630c572c704
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1010-comtft.dts
@@ -0,0 +1,42 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2014-2017 Lothar Waßmann <LW@KARO-electronics.de>
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-tx6.dtsi"
+#include "imx6qdl-tx6-lcd.dtsi"
+
+/ {
+	model = "Ka-Ro electronics TX6Q-1010 Module on CoMpact TFT";
+	compatible = "karo,imx6q-tx6q", "fsl,imx6q";
+};
+
+&backlight {
+	pwms = <&pwm2 0 500000 0>;
+};
+
+&can1 {
+	status = "disabled";
+};
+
+&can2 {
+	xceiver-supply = <&reg_3v3>;
+};
+
+&kpp {
+	status = "disabled";
+};
+
+&lcd_panel {
+	compatible = "edt,etm0700g0edh6";
+};
+
+&reg_can_xcvr {
+	status = "disabled";
+};
+
+&touchscreen {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1010.dts b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1010.dts
new file mode 100644
index 000000000000..01ac3493fa32
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1010.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2014-2017 Lothar Waßmann <LW@KARO-electronics.de>
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-tx6.dtsi"
+#include "imx6qdl-tx6-lcd.dtsi"
+
+/ {
+	model = "Ka-Ro electronics TX6Q-1010/-1030 Module";
+	compatible = "karo,imx6q-tx6q", "fsl,imx6q";
+};
+
+&ipu2 {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1020-comtft.dts b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1020-comtft.dts
new file mode 100644
index 000000000000..1013025cb2d5
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1020-comtft.dts
@@ -0,0 +1,73 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2014-2017 Lothar Waßmann <LW@KARO-electronics.de>
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-tx6.dtsi"
+#include "imx6qdl-tx6-lcd.dtsi"
+
+/ {
+	model = "Ka-Ro electronics TX6Q-1020 Module on CoMpact TFT";
+	compatible = "karo,imx6q-tx6q", "fsl,imx6q";
+};
+
+&backlight {
+	pwms = <&pwm2 0 500000 0>;
+};
+
+&can1 {
+	status = "disabled";
+};
+
+&can2 {
+	xceiver-supply = <&reg_3v3>;
+};
+
+&ds1339 {
+	status = "disabled";
+};
+
+&gpmi {
+	status = "disabled";
+};
+
+&kpp {
+	status = "disabled";
+};
+
+&lcd_panel {
+	compatible = "edt,etm0700g0edh6";
+};
+
+&reg_can_xcvr {
+	status = "disabled";
+};
+
+&touchscreen {
+	status = "disabled";
+};
+
+&usdhc4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	bus-width = <4>;
+	no-1-8-v;
+	fsl,wp-controller;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x070b1
+			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x070b1
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x070b1
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x070b1
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x070b1
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x070b1
+			MX6QDL_PAD_NANDF_ALE__SD4_RESET		0x0b0b1
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1020.dts b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1020.dts
new file mode 100644
index 000000000000..5dd8f1642db3
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1020.dts
@@ -0,0 +1,50 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2014-2017 Lothar Waßmann <LW@KARO-electronics.de>
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-tx6.dtsi"
+#include "imx6qdl-tx6-lcd.dtsi"
+
+/ {
+	model = "Ka-Ro electronics TX6Q-1020 Module";
+	compatible = "karo,imx6q-tx6q", "fsl,imx6q";
+};
+
+&ds1339 {
+	status = "disabled";
+};
+
+&gpmi {
+	status = "disabled";
+};
+
+&ipu2 {
+	status = "disabled";
+};
+
+&usdhc4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	bus-width = <4>;
+	non-removable;
+	no-1-8-v;
+	fsl,wp-controller;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x070b1
+			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x070b1
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x070b1
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x070b1
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x070b1
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x070b1
+			MX6QDL_PAD_NANDF_ALE__SD4_RESET		0x0b0b1
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1036-mb7.dts b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1036-mb7.dts
new file mode 100644
index 000000000000..ffa79c0eb05a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1036-mb7.dts
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
+ */
+
+/dts-v1/;
+#include "imx6q-tx6q-1036.dts"
+#include "imx6qdl-tx6-mb7.dtsi"
+
+/ {
+	model = "Ka-Ro electronics TX6Q-1036 Module on MB7 baseboard";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1036.dts b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1036.dts
new file mode 100644
index 000000000000..1346fd663d68
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1036.dts
@@ -0,0 +1,50 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2014-2017 Lothar Waßmann <LW@KARO-electronics.de>
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-tx6.dtsi"
+#include "imx6qdl-tx6-lcd.dtsi"
+
+/ {
+	model = "Ka-Ro electronics TX6Q-1036 Module";
+	compatible = "karo,imx6q-tx6q", "fsl,imx6q";
+};
+
+&ds1339 {
+	status = "disabled";
+};
+
+&gpmi {
+	status = "disabled";
+};
+
+&ipu2 {
+	status = "disabled";
+};
+
+&usdhc4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	bus-width = <4>;
+	non-removable;
+	no-1-8-v;
+	fsl,wp-controller;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x070b1
+			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x070b1
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x070b1
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x070b1
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x070b1
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x070b1
+			MX6QDL_PAD_NANDF_ALE__SD4_RESET		0x0b0b1
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-10x0-mb7.dts b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-10x0-mb7.dts
new file mode 100644
index 000000000000..eac07d5944cc
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-10x0-mb7.dts
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
+ */
+
+/dts-v1/;
+#include "imx6q-tx6q-1010.dts"
+#include "imx6qdl-tx6-mb7.dtsi"
+
+/ {
+	model = "Ka-Ro electronics TX6Q-1010/-1030 Module on MB7 baseboard";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1110.dts b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1110.dts
new file mode 100644
index 000000000000..c485da35d333
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-1110.dts
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2014-2017 Lothar Waßmann <LW@KARO-electronics.de>
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-tx6.dtsi"
+#include "imx6qdl-tx6-lvds.dtsi"
+
+/ {
+	model = "Ka-Ro electronics TX6Q-1110/-1130 Module";
+	compatible = "karo,imx6q-tx6q", "fsl,imx6q";
+};
+
+&ipu2 {
+	status = "disabled";
+};
+
+&sata {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-11x0-mb7.dts b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-11x0-mb7.dts
new file mode 100644
index 000000000000..53304fc3a90b
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-tx6q-11x0-mb7.dts
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2016-2017 Lothar Waßmann <LW@KARO-electronics.de>
+ */
+
+/dts-v1/;
+#include "imx6q-tx6q-1110.dts"
+#include "imx6qdl-tx6-mb7.dtsi"
+
+/ {
+	model = "Ka-Ro electronics TX6Q-1110/-1130 Module on MB7 baseboard";
+};
diff --git a/arch/arm/boot/dts/imx6q-udoo.dts b/arch/arm/boot/dts/nxp/imx/imx6q-udoo.dts
index 52e9f4a211d0..52e9f4a211d0 100644
--- a/arch/arm/boot/dts/imx6q-udoo.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-udoo.dts
diff --git a/arch/arm/boot/dts/imx6q-utilite-pro.dts b/arch/arm/boot/dts/nxp/imx/imx6q-utilite-pro.dts
index d16ff2083d62..aae81feee00d 100644
--- a/arch/arm/boot/dts/imx6q-utilite-pro.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-utilite-pro.dts
@@ -89,7 +89,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_keys>;
 
-		power {
+		key-power {
 			label = "Power Button";
 			gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -296,7 +296,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_100mhz: usdhc3grp-100mhz {
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD	0x170B9
 			MX6QDL_PAD_SD3_CLK__SD3_CLK	0x100B9
@@ -307,7 +307,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_200mhz: usdhc3grp-200mhz {
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD	0x170F9
 			MX6QDL_PAD_SD3_CLK__SD3_CLK	0x100F9
diff --git a/arch/arm/boot/dts/imx6q-var-dt6customboard.dts b/arch/arm/boot/dts/nxp/imx/imx6q-var-dt6customboard.dts
index 63550351340d..0225a621ec7a 100644
--- a/arch/arm/boot/dts/imx6q-var-dt6customboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-var-dt6customboard.dts
@@ -18,7 +18,7 @@
 
 	backlight_lvds: backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm2 0 50000>;
+		pwms = <&pwm2 0 50000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 248>;
 		default-brightness-level = <7>;
 		status = "okay";
@@ -28,7 +28,7 @@
 		compatible = "gpio-keys";
 		autorepeat;
 
-		back {
+		key-back {
 			gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_BACK>;
 			label = "Key Back";
@@ -37,7 +37,7 @@
 			wakeup-source;
 		};
 
-		home {
+		key-home {
 			gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_HOME>;
 			label = "Key Home";
@@ -46,7 +46,7 @@
 			wakeup-source;
 		};
 
-		menu {
+		key-menu {
 			gpios = <&gpio4 25 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_MENU>;
 			label = "Key Menu";
@@ -203,7 +203,6 @@
 };
 
 &pwm2 {
-	#pwm-cells = <2>;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-var-mx6customboard.dts b/arch/arm/boot/dts/nxp/imx/imx6q-var-mx6customboard.dts
new file mode 100644
index 000000000000..18a620832a2a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-var-mx6customboard.dts
@@ -0,0 +1,247 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Support for Variscite MX6 Carrier-board
+ *
+ * Copyright 2016 Variscite, Ltd. All Rights Reserved
+ * Copyright 2022 Bootlin
+ */
+
+/dts-v1/;
+
+#include "imx6qdl-var-som.dtsi"
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	model = "Variscite i.MX6 QUAD/DUAL VAR-SOM-MX6 Custom Board";
+	compatible = "variscite,mx6customboard", "variscite,var-som-imx6q", "fsl,imx6q";
+
+	panel0: lvds-panel0 {
+		compatible = "panel-lvds";
+		backlight = <&backlight_lvds>;
+		width-mm = <152>;
+		height-mm = <91>;
+		label = "etm070001adh6";
+		data-mapping = "jeida-18";
+
+		panel-timing {
+			clock-frequency = <32000000>;
+			hactive = <800>;
+			vactive = <480>;
+			hback-porch = <39>;
+			hfront-porch = <39>;
+			vback-porch = <29>;
+			vfront-porch = <13>;
+			hsync-len = <47>;
+			vsync-len = <2>;
+		};
+
+		port {
+			panel_in_lvds0: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+
+	panel1: lvds-panel1 {
+		compatible = "panel-lvds";
+		width-mm = <152>;
+		height-mm = <91>;
+		data-mapping = "jeida-18";
+
+		panel-timing {
+			clock-frequency = <38251000>;
+			hactive = <800>;
+			vactive = <600>;
+			hback-porch = <112>;
+			hfront-porch = <32>;
+			vback-porch = <3>;
+			vfront-porch = <17>;
+			hsync-len = <80>;
+			vsync-len = <4>;
+		};
+
+		port {
+			panel_in_lvds1: endpoint {
+				remote-endpoint = <&lvds1_out>;
+			};
+		};
+	};
+
+	backlight_lvds: backlight-lvds {
+		compatible = "pwm-backlight";
+		pwms = <&pwm2 0 50000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 248>;
+		default-brightness-level = <7>;
+		power-supply = <&reg_3p3v>;
+	};
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	touchscreen@24 {
+		compatible = "cypress,tt21000";
+		reg = <0x24>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+		vdd-supply = <&reg_3p3v>;
+		touchscreen-size-x = <880>;
+		touchscreen-size-y = <1280>;
+	};
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5306";
+		reg = <0x38>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+		touchscreen-size-x = <1800>;
+		touchscreen-size-y = <1000>;
+	};
+};
+
+&iomuxc {
+	pinctrl_camera: cameragrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19		0x1b0b0
+			MX6QDL_PAD_CSI0_DATA_EN__IPU1_CSI0_DATA_EN	0x1b0b0
+			MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK	0x1b0b0
+			MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC		0x1b0b0
+			MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC		0x1b0b0
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_7__FLEXCAN1_TX		0x1b0b0
+			MX6QDL_PAD_GPIO_8__FLEXCAN1_RX		0x1b0b0
+		>;
+	};
+
+	pinctrl_ipu1: ipu1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x10
+			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15		0x10
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x10
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x10
+			MX6QDL_PAD_DI0_PIN4__IPU1_DI0_PIN04		0x10
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x10
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x10
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x10
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x10
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x10
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x10
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x10
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x10
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x10
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x10
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x10
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x10
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x10
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x10
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x10
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x10
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x10
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x10
+			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18	0x10
+			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19	0x10
+			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20	0x10
+			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21	0x10
+			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22	0x10
+			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23	0x10
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D23__UART3_CTS_B		0x1b0b1
+			MX6QDL_PAD_EIM_EB3__UART3_RTS_B		0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg_var: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x17059
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD		0x17071
+			MX6QDL_PAD_SD1_CLK__SD1_CLK		0x10071
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0		0x17071
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1		0x17071
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2		0x17071
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3		0x17071
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+		>;
+	};
+};
+
+&ldb {
+	status = "okay";
+
+	lvds-channel@0 {
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <24>;
+		status = "okay";
+
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in_lvds0>;
+			};
+		};
+	};
+
+	lvds-channel@1 {
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <24>;
+		status = "okay";
+
+		port@4 {
+			reg = <4>;
+
+			lvds1_out: endpoint {
+				remote-endpoint = <&panel_in_lvds1>;
+			};
+		};
+	};
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	cd-gpios = <&gpio4 14 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6q-vicut1.dts b/arch/arm/boot/dts/nxp/imx/imx6q-vicut1.dts
index 0a4e251be162..dd91aff3f9e2 100644
--- a/arch/arm/boot/dts/imx6q-vicut1.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-vicut1.dts
@@ -6,12 +6,9 @@
 /dts-v1/;
 #include "imx6q.dtsi"
 #include "imx6qdl-vicut1.dtsi"
+#include "imx6qdl-vicut1-12inch.dtsi"
 
 / {
 	model = "Kverneland UT1Q Board";
 	compatible = "kvg,vicut1q", "fsl,imx6q";
 };
-
-&sata {
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6q-wandboard-revb1.dts b/arch/arm/boot/dts/nxp/imx/imx6q-wandboard-revb1.dts
index f6ccbecff92c..f6ccbecff92c 100644
--- a/arch/arm/boot/dts/imx6q-wandboard-revb1.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-wandboard-revb1.dts
diff --git a/arch/arm/boot/dts/imx6q-wandboard-revd1.dts b/arch/arm/boot/dts/nxp/imx/imx6q-wandboard-revd1.dts
index 55331021d80c..55331021d80c 100644
--- a/arch/arm/boot/dts/imx6q-wandboard-revd1.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-wandboard-revd1.dts
diff --git a/arch/arm/boot/dts/imx6q-wandboard.dts b/arch/arm/boot/dts/nxp/imx/imx6q-wandboard.dts
index 0be548beef86..0be548beef86 100644
--- a/arch/arm/boot/dts/imx6q-wandboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-wandboard.dts
diff --git a/arch/arm/boot/dts/imx6q-yapp4-crux.dts b/arch/arm/boot/dts/nxp/imx/imx6q-yapp4-crux.dts
index 15f4824a5142..bddf3822ebf7 100644
--- a/arch/arm/boot/dts/imx6q-yapp4-crux.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-yapp4-crux.dts
@@ -33,6 +33,10 @@
 	status = "okay";
 };
 
+&reg_pu {
+	regulator-always-on;
+};
+
 &reg_usb_h1_vbus {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/nxp/imx/imx6q-yapp4-pegasus.dts b/arch/arm/boot/dts/nxp/imx/imx6q-yapp4-pegasus.dts
new file mode 100644
index 000000000000..ec6651ba4ba2
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-yapp4-pegasus.dts
@@ -0,0 +1,58 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2021 Y Soft Corporation, a.s.
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6dl-yapp43-common.dtsi"
+
+/ {
+	model = "Y Soft IOTA Pegasus i.MX6Quad board";
+	compatible = "ysoft,imx6q-yapp4-pegasus", "fsl,imx6q";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0xf0000000>;
+	};
+};
+
+&gpio_oled {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&leds {
+	status = "okay";
+};
+
+&oled_1305 {
+	status = "okay";
+};
+
+&oled_1309 {
+	status = "okay";
+};
+
+&reg_pu {
+	regulator-always-on;
+};
+
+&reg_usb_h1_vbus {
+	status = "okay";
+};
+
+&touchkeys {
+	status = "okay";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbphy2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6q-zii-rdu2.dts b/arch/arm/boot/dts/nxp/imx/imx6q-zii-rdu2.dts
index a1c5e69d81ba..a1c5e69d81ba 100644
--- a/arch/arm/boot/dts/imx6q-zii-rdu2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6q-zii-rdu2.dts
diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/nxp/imx/imx6q.dtsi
index 9caba4529c71..df86049a695b 100644
--- a/arch/arm/boot/dts/imx6q.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6q.dtsi
@@ -159,14 +159,17 @@
 		};
 	};
 
-	soc {
+	soc: soc {
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x40000>;
+			ranges = <0 0x00900000 0x40000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
-		bus@2000000 { /* AIPS1 */
+		aips1: bus@2000000 { /* AIPS1 */
 			spba-bus@2000000 {
 				ecspi5: spi@2018000 {
 					#address-cells = <1>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-apalis-v1.2.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-apalis-v1.2.dtsi
new file mode 100644
index 000000000000..83fa04fc9f18
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-apalis-v1.2.dtsi
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/* Copyright (c) 2025 Toradex */
+
+&i2c2 {
+	/delete-node/ stmpe811@41;
+
+	ad7879_ts: touchscreen@2c {
+		compatible = "adi,ad7879-1";
+		reg = <0x2c>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touch_int>;
+		interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio4>;
+		touchscreen-max-pressure = <4096>;
+		adi,resistance-plate-x = <120>;
+		adi,first-conversion-delay = /bits/ 8 <3>;
+		adi,acquisition-time = /bits/ 8 <1>;
+		adi,median-filter-size = /bits/ 8 <2>;
+		adi,averaging = /bits/ 8 <1>;
+		adi,conversion-interval = /bits/ 8 <255>;
+	};
+
+	tla2024_adc: adc@49 {
+		compatible = "ti,tla2024";
+		reg = <0x49>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Apalis AN1_ADC0 */
+		channel@4 {
+			reg = <4>;
+			ti,datarate = <4>;
+			ti,gain = <1>;
+		};
+
+		/* Apalis AN1_ADC1 */
+		channel@5 {
+			reg = <5>;
+			ti,datarate = <4>;
+			ti,gain = <1>;
+		};
+
+		/* Apalis AN1_ADC2 */
+		channel@6 {
+			reg = <6>;
+			ti,datarate = <4>;
+			ti,gain = <1>;
+		};
+
+		/* Apalis AN1_TSWIP_ADC3 */
+		channel@7 {
+			reg = <7>;
+			ti,datarate = <4>;
+			ti,gain = <1>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/imx6qdl-apalis.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-apalis.dtsi
index ed2739e39085..5fcd7cdb7001 100644
--- a/arch/arm/boot/dts/imx6qdl-apalis.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-apalis.dtsi
@@ -1,15 +1,22 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2014-2020 Toradex
+ * Copyright 2014-2022 Toradex
  * Copyright 2012 Freescale Semiconductor, Inc.
  * Copyright 2011 Linaro Ltd.
  */
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
 
 / {
 	model = "Toradex Apalis iMX6Q/D Module";
-	compatible = "toradex,apalis_imx6q", "fsl,imx6q";
+
+	aliases {
+		mmc0 = &usdhc3; /* eMMC */
+		mmc1 = &usdhc1; /* MMC1 slot */
+		mmc2 = &usdhc2; /* SD1 slot */
+		/delete-property/ mmc3;
+	};
 
 	/* Will be filled by the bootloader */
 	memory@10000000 {
@@ -19,88 +26,196 @@
 
 	backlight: backlight {
 		compatible = "pwm-backlight";
+		brightness-levels = <0 45 63 88 119 158 203 255>;
+		default-brightness-level = <4>;
+		enable-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_bl_on>;
-		pwms = <&pwm4 0 5000000>;
-		enable-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
+		power-supply = <&reg_module_3v3>;
+		pwms = <&pwm4 0 5000000 PWM_POLARITY_INVERTED>;
+		status = "disabled";
+	};
+
+	clk_ov5640_osc: clk-ov5640-osc {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		key-wakeup {
+			debounce-interval = <10>;
+			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+			label = "Wake-Up";
+			linux,code = <KEY_WAKEUP>;
+			wakeup-source;
+		};
+	};
+
+	lcd_display: disp0 {
+		compatible = "fsl,imx-parallel-display";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interface-pix-fmt = "rgb24";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu1_lcdif>;
 		status = "disabled";
+
+		port@0 {
+			reg = <0>;
+
+			lcd_display_in: endpoint {
+				remote-endpoint = <&ipu1_di1_disp1>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			lcd_display_out: endpoint {
+				remote-endpoint = <&lcd_panel_in>;
+			};
+		};
+	};
+
+	panel_dpi: panel-dpi {
+		compatible = "edt,et057090dhu";
+		backlight = <&backlight>;
+
+		status = "disabled";
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
+	};
+
+	panel_lvds: panel-lvds {
+		compatible = "panel-lvds";
+		backlight = <&backlight>;
+		status = "disabled";
+
+		port {
+			lvds_panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+
+	poweroff {
+		compatible = "regulator-poweroff";
+		cpu-supply = <&vgen2_reg>;
 	};
 
 	reg_module_3v3: regulator-module-3v3 {
 		compatible = "regulator-fixed";
-		regulator-name = "+V3.3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
 		regulator-always-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "+V3.3";
 	};
 
 	reg_module_3v3_audio: regulator-module-3v3-audio {
 		compatible = "regulator-fixed";
-		regulator-name = "+V3.3_AUDIO";
-		regulator-min-microvolt = <3300000>;
+		regulator-always-on;
 		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "+V3.3_AUDIO";
+	};
+
+	reg_ov5640_1v8_d_o_vdd: regulator-ov5640-1v8-d-o-vdd {
+		compatible = "regulator-fixed";
 		regulator-always-on;
+		regulator-max-microvolt = <1800000>;
+		regulator-min-microvolt = <1800000>;
+		regulator-name = "DOVDD/DVDD_1.8V";
+		/* Note: The CSI module uses on-board 3.3V_SW supply */
+		vin-supply = <&reg_module_3v3>;
+	};
+
+	reg_ov5640_2v8_a_vdd: regulator-ov5640-2v8-a-vdd {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <2800000>;
+		regulator-min-microvolt = <2800000>;
+		regulator-name = "AVDD/AFVDD_2.8V";
+		/* Note: The CSI module uses on-board 3.3V_SW supply */
+		vin-supply = <&reg_module_3v3>;
 	};
 
 	reg_usb_otg_vbus: regulator-usb-otg-vbus {
 		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_regulator_usbotg_pwr>;
-		regulator-name = "usb_otg_vbus";
-		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb_otg_vbus";
 		status = "disabled";
 	};
 
 	/* on module USB hub */
 	reg_usb_host_vbus_hub: regulator-usb-host-vbus-hub {
 		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio3 28 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_regulator_usbhub_pwr>;
-		regulator-name = "usb_host_vbus_hub";
-		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio3 28 GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb_host_vbus_hub";
 		startup-delay-us = <2000>;
-		enable-active-high;
 		status = "okay";
 	};
 
 	reg_usb_host_vbus: regulator-usb-host-vbus {
 		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_regulator_usbh_pwr>;
-		regulator-name = "usb_host_vbus";
-		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
-		gpio =  <&gpio1 0 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb_host_vbus";
 		vin-supply = <&reg_usb_host_vbus_hub>;
 		status = "disabled";
 	};
 
 	sound {
 		compatible = "fsl,imx-audio-sgtl5000";
-		model = "imx6q-apalis-sgtl5000";
-		ssi-controller = <&ssi1>;
 		audio-codec = <&codec>;
 		audio-routing =
 			"LINE_IN", "Line In Jack",
 			"MIC_IN", "Mic Jack",
 			"Mic Jack", "Mic Bias",
 			"Headphone Jack", "HP_OUT";
-		mux-int-port = <1>;
+		model = "apalis-imx6";
 		mux-ext-port = <4>;
+		mux-int-port = <1>;
+		ssi-controller = <&ssi1>;
+	};
+
+	spdif_out: spdif-out {
+		compatible = "linux,spdif-dit";
+		#sound-dai-cells = <0>;
+	};
+
+	spdif_in: spdif-in {
+		compatible = "linux,spdif-dir";
+		#sound-dai-cells = <0>;
 	};
 
 	sound_spdif: sound-spdif {
 		compatible = "fsl,imx-audio-spdif";
+		audio-cpu = <&spdif>;
+		audio-codec = <&spdif_out>, <&spdif_in>;
 		model = "imx-spdif";
-		spdif-controller = <&spdif>;
-		spdif-in;
-		spdif-out;
 		status = "disabled";
 	};
 };
@@ -141,6 +256,214 @@
 	status = "disabled";
 };
 
+&gpio1 {
+	gpio-line-names = "MXM3_84",
+			  "MXM3_4",
+			  "MXM3_15/GPIO7",
+			  "MXM3_96",
+			  "MXM3_37",
+			  "",
+			  "MXM3_17/GPIO8",
+			  "MXM3_14",
+			  "MXM3_12",
+			  "MXM3_2",
+			  "MXM3_184",
+			  "MXM3_180",
+			  "MXM3_178",
+			  "MXM3_176",
+			  "MXM3_188",
+			  "MXM3_186",
+			  "MXM3_160",
+			  "MXM3_162",
+			  "MXM3_150",
+			  "MXM3_144",
+			  "MXM3_154",
+			  "MXM3_146",
+			  "",
+			  "",
+			  "MXM3_72";
+};
+
+&gpio2 {
+	gpio-line-names = "MXM3_148",
+			  "MXM3_152",
+			  "MXM3_156",
+			  "MXM3_158",
+			  "MXM3_1/GPIO1",
+			  "MXM3_3/GPIO2",
+			  "MXM3_5/GPIO3",
+			  "MXM3_7/GPIO4",
+			  "MXM3_95",
+			  "MXM3_6",
+			  "MXM3_8",
+			  "MXM3_123",
+			  "MXM3_126",
+			  "MXM3_128",
+			  "MXM3_130",
+			  "MXM3_132",
+			  "MXM3_253",
+			  "MXM3_251",
+			  "MXM3_283",
+			  "MXM3_281",
+			  "MXM3_279",
+			  "MXM3_277",
+			  "MXM3_243",
+			  "MXM3_235",
+			  "MXM3_231",
+			  "MXM3_229",
+			  "MXM3_233",
+			  "MXM3_198",
+			  "MXM3_275",
+			  "MXM3_273",
+			  "MXM3_207",
+			  "MXM3_122";
+};
+
+&gpio3 {
+	gpio-line-names = "MXM3_271",
+			  "MXM3_269",
+			  "MXM3_301",
+			  "MXM3_299",
+			  "MXM3_297",
+			  "MXM3_295",
+			  "MXM3_293",
+			  "MXM3_291",
+			  "MXM3_289",
+			  "MXM3_287",
+			  "MXM3_249",
+			  "MXM3_247",
+			  "MXM3_245",
+			  "MXM3_286",
+			  "MXM3_239",
+			  "MXM3_35",
+			  "MXM3_205",
+			  "MXM3_203",
+			  "MXM3_201",
+			  "MXM3_116",
+			  "MXM3_114",
+			  "MXM3_262",
+			  "MXM3_274",
+			  "MXM3_124",
+			  "MXM3_110",
+			  "MXM3_120",
+			  "MXM3_263",
+			  "MXM3_265",
+			  "",
+			  "MXM3_135",
+			  "MXM3_261",
+			  "MXM3_259";
+};
+
+&gpio4 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "MXM3_194",
+			  "MXM3_136",
+			  "MXM3_134",
+			  "MXM3_140",
+			  "MXM3_138",
+			  "",
+			  "MXM3_220",
+			  "",
+			  "",
+			  "MXM3_18",
+			  "MXM3_16",
+			  "",
+			  "",
+			  "MXM3_214",
+			  "MXM3_216",
+			  "MXM3_164";
+};
+
+&gpio5 {
+	gpio-line-names = "MXM3_159",
+			  "",
+			  "",
+			  "",
+			  "MXM3_257",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "MXM3_200",
+			  "MXM3_196",
+			  "MXM3_204",
+			  "MXM3_202",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "MXM3_191",
+			  "MXM3_197",
+			  "MXM3_77",
+			  "MXM3_195",
+			  "MXM3_221",
+			  "MXM3_225",
+			  "MXM3_223",
+			  "MXM3_227",
+			  "MXM3_209",
+			  "MXM3_211",
+			  "MXM3_118",
+			  "MXM3_112",
+			  "MXM3_187",
+			  "MXM3_185";
+};
+
+&gpio6 {
+	gpio-line-names = "MXM3_183",
+			  "MXM3_181",
+			  "MXM3_179",
+			  "MXM3_177",
+			  "MXM3_175",
+			  "MXM3_173",
+			  "MXM3_255",
+			  "MXM3_83",
+			  "MXM3_91",
+			  "MXM3_13/GPIO6",
+			  "MXM3_11/GPIO5",
+			  "MXM3_79",
+			  "",
+			  "",
+			  "MXM3_190",
+			  "MXM3_193",
+			  "MXM3_89";
+};
+
+&gpio7 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "MXM3_99",
+			  "MXM3_85",
+			  "MXM3_217",
+			  "MXM3_215";
+};
+
+&gpr {
+	ipu1_csi0_mux {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+
+		port@1 {
+			reg = <1>;
+			ipu1_csi0_mux_from_parallel_sensor: endpoint {
+				remote-endpoint = <&adv7280_to_ipu1_csi0_mux>;
+			};
+		};
+	};
+};
+
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
@@ -177,6 +500,16 @@
 	scl-gpios = <&gpio5 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	sda-gpios = <&gpio5 26 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "disabled";
+
+	atmel_mxt_ts: touchscreen@4a {
+		compatible = "atmel,maxtouch";
+		/* These GPIOs are muxed with the iomuxc node */
+		interrupt-parent = <&gpio6>;
+		interrupts = <10 IRQ_TYPE_EDGE_FALLING>;	/* MXM3_11 */
+		reg = <0x4a>;
+		reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>;	/* MXM3_13 */
+		status = "disabled";
+	};
 };
 
 /*
@@ -192,101 +525,104 @@
 	sda-gpios = <&gpio4 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
 		reg = <0x08>;
 
 		regulators {
 			sw1a_reg: sw1ab {
-				regulator-min-microvolt = <300000>;
-				regulator-max-microvolt = <1875000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1875000>;
+				regulator-min-microvolt = <300000>;
 				regulator-ramp-delay = <6250>;
 			};
 
 			sw1c_reg: sw1c {
-				regulator-min-microvolt = <300000>;
-				regulator-max-microvolt = <1875000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1875000>;
+				regulator-min-microvolt = <300000>;
 				regulator-ramp-delay = <6250>;
 			};
 
 			sw3a_reg: sw3a {
-				regulator-min-microvolt = <400000>;
-				regulator-max-microvolt = <1975000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1975000>;
+				regulator-min-microvolt = <400000>;
 			};
 
 			swbst_reg: swbst {
-				regulator-min-microvolt = <5000000>;
-				regulator-max-microvolt = <5150000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <5150000>;
+				regulator-min-microvolt = <5000000>;
 			};
 
 			snvs_reg: vsnvs {
-				regulator-min-microvolt = <1000000>;
-				regulator-max-microvolt = <3000000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3000000>;
+				regulator-min-microvolt = <1000000>;
 			};
 
 			vref_reg: vrefddr {
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
 			};
 
 			vgen1_reg: vgen1 {
-				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <1550000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1550000>;
+				regulator-min-microvolt = <800000>;
 			};
 
 			vgen2_reg: vgen2 {
-				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <1550000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1550000>;
+				regulator-min-microvolt = <800000>;
 			};
 
 			vgen3_reg: vgen3 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
 			};
 
 			vgen4_reg: vgen4 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
 			};
 
 			vgen5_reg: vgen5 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
 			};
 
 			vgen6_reg: vgen6 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
 			};
 		};
 	};
 
 	codec: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
-		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sgtl5000>;
+		reg = <0x0a>;
 		VDDA-supply = <&reg_module_3v3_audio>;
 		VDDIO-supply = <&reg_module_3v3>;
 		VDDD-supply = <&vgen4_reg>;
@@ -295,15 +631,14 @@
 	/* STMPE811 touch screen controller */
 	stmpe811@41 {
 		compatible = "st,stmpe811";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_touch_int>;
-		reg = <0x41>;
+		blocks = <0x5>;
+		id = <0>;
 		interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-parent = <&gpio4>;
-		interrupt-controller;
-		id = <0>;
-		blocks = <0x5>;
 		irq-trigger = <0x1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touch_int>;
+		reg = <0x41>;
 		/* 3.25 MHz ADC clock speed */
 		st,adc-freq = <1>;
 		/* 12-bit ADC */
@@ -313,7 +648,7 @@
 		/* ADC conversion time: 80 clocks */
 		st,sample-time = <4>;
 
-		stmpe_touchscreen: stmpe-touchscreen {
+		stmpe_ts: touchscreen {
 			compatible = "st,stmpe-ts";
 			/* 8 sample average control */
 			st,ave-ctrl = <3>;
@@ -330,11 +665,11 @@
 			st,touch-det-delay = <5>;
 		};
 
-		stmpe_adc: stmpe-adc {
+		stmpe_adc: adc {
 			compatible = "st,stmpe-adc";
+			#io-channel-cells = <1>;
 			/* forbid to use ADC channels 3-0 (touch) */
 			st,norequest-mask = <0x0F>;
-			#io-channel-cells = <1>;
 		};
 	};
 };
@@ -351,6 +686,90 @@
 	scl-gpios = <&gpio3 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	sda-gpios = <&gpio3 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "disabled";
+
+	adv_7280: adv7280@21 {
+		compatible = "adi,adv7280";
+		adi,force-bt656-4;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu1_csi0>;
+		reg = <0x21>;
+		status = "disabled";
+
+		port {
+			adv7280_to_ipu1_csi0_mux: endpoint {
+				bus-width = <8>;
+				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+			};
+		};
+	};
+
+	ov5640_csi_cam: ov5640_mipi@3c {
+		compatible = "ovti,ov5640";
+		AVDD-supply = <&reg_ov5640_2v8_a_vdd>;
+		DOVDD-supply = <&reg_ov5640_1v8_d_o_vdd>;
+		DVDD-supply = <&reg_ov5640_1v8_d_o_vdd>;
+		clock-names = "xclk";
+		clocks = <&clks IMX6QDL_CLK_CKO2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_cam_mclk>;
+		/* These GPIOs are muxed with the iomuxc node */
+		powerdown-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
+		reg = <0x3c>;
+		reset-gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
+		status = "disabled";
+
+		port {
+			ov5640_to_mipi_csi2: endpoint {
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+				remote-endpoint = <&mipi_csi_from_ov5640>;
+			};
+		};
+	};
+};
+
+&ipu1_di1_disp1 {
+	remote-endpoint = <&lcd_display_in>;
+};
+
+&ldb {
+	lvds-channel@0 {
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&lvds_panel_in>;
+			};
+		};
+	};
+
+	lvds-channel@1 {
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <18>;
+
+		port@4 {
+			reg = <4>;
+
+			lvds1_out: endpoint {
+			};
+		};
+	};
+};
+
+&mipi_csi {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "disabled";
+
+	port@0 {
+		reg = <0>;
+
+		mipi_csi_from_ov5640: endpoint {
+			clock-lanes = <0>;
+			data-lanes = <1 2>;
+			remote-endpoint = <&ov5640_to_mipi_csi2>;
+		};
+	};
 };
 
 &pwm1 {
@@ -372,7 +791,6 @@
 };
 
 &pwm4 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "disabled";
@@ -389,72 +807,72 @@
 };
 
 &uart1 {
+	fsl,dte-mode;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1_dte &pinctrl_uart1_ctrl>;
-	fsl,dte-mode;
 	uart-has-rtscts;
 	status = "disabled";
 };
 
 &uart2 {
+	fsl,dte-mode;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart2_dte>;
-	fsl,dte-mode;
 	uart-has-rtscts;
 	status = "disabled";
 };
 
 &uart4 {
+	fsl,dte-mode;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart4_dte>;
-	fsl,dte-mode;
 	status = "disabled";
 };
 
 &uart5 {
+	fsl,dte-mode;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart5_dte>;
-	fsl,dte-mode;
 	status = "disabled";
 };
 
 &usbotg {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usbotg>;
-	disable-over-current;
 	status = "disabled";
 };
 
 /* MMC1 */
 &usdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc1_4bit &pinctrl_usdhc1_8bit>;
-	vqmmc-supply = <&reg_module_3v3>;
 	bus-width = <8>;
+	cd-gpios = <&gpio4 20 GPIO_ACTIVE_LOW>;
 	disable-wp;
 	no-1-8-v;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1_4bit &pinctrl_usdhc1_8bit &pinctrl_mmc_cd>;
+	vqmmc-supply = <&reg_module_3v3>;
 	status = "disabled";
 };
 
 /* SD1 */
 &usdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc2>;
-	vqmmc-supply = <&reg_module_3v3>;
 	bus-width = <4>;
 	disable-wp;
 	no-1-8-v;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	vqmmc-supply = <&reg_module_3v3>;
 	status = "disabled";
 };
 
 /* eMMC */
 &usdhc3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc3>;
-	vqmmc-supply = <&reg_module_3v3>;
 	bus-width = <8>;
 	no-1-8-v;
 	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	vqmmc-supply = <&reg_module_3v3>;
 	status = "okay";
 };
 
@@ -463,49 +881,57 @@
 };
 
 &iomuxc {
-	pinctrl_apalis_gpio1: gpio2io04grp {
+	/* Mux the Apalis GPIOs */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_apalis_gpio1 &pinctrl_apalis_gpio2
+		     &pinctrl_apalis_gpio3 &pinctrl_apalis_gpio4
+		     &pinctrl_apalis_gpio5 &pinctrl_apalis_gpio6
+		     &pinctrl_apalis_gpio7 &pinctrl_apalis_gpio8
+		    >;
+
+	pinctrl_apalis_gpio1: apalisgpio1grp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D4__GPIO2_IO04 0x130b0
 		>;
 	};
 
-	pinctrl_apalis_gpio2: gpio2io05grp {
+	pinctrl_apalis_gpio2: apalisgpio2grp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D5__GPIO2_IO05 0x130b0
 		>;
 	};
 
-	pinctrl_apalis_gpio3: gpio2io06grp {
+	pinctrl_apalis_gpio3: apalisgpio3grp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D6__GPIO2_IO06 0x130b0
 		>;
 	};
 
-	pinctrl_apalis_gpio4: gpio2io07grp {
+	pinctrl_apalis_gpio4: apalisgpio4grp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D7__GPIO2_IO07 0x130b0
 		>;
 	};
 
-	pinctrl_apalis_gpio5: gpio6io10grp {
+	pinctrl_apalis_gpio5: apalisgpio5grp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 0x130b0
 		>;
 	};
 
-	pinctrl_apalis_gpio6: gpio6io09grp {
+	pinctrl_apalis_gpio6: apalisgpio6grp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09 0x130b0
 		>;
 	};
 
-	pinctrl_apalis_gpio7: gpio1io02grp {
+	pinctrl_apalis_gpio7: apalisgpio7grp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x130b0
 		>;
 	};
 
-	pinctrl_apalis_gpio8: gpio1io06grp {
+	pinctrl_apalis_gpio8: apalisgpio8grp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x130b0
 		>;
@@ -517,8 +943,6 @@
 			MX6QDL_PAD_DISP0_DAT21__AUD4_TXD	0x130b0
 			MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS	0x130b0
 			MX6QDL_PAD_DISP0_DAT23__AUD4_RXD	0x130b0
-			/* SGTL5000 sys_mclk */
-			MX6QDL_PAD_GPIO_5__CCM_CLKO1		0x130b0
 		>;
 	};
 
@@ -600,7 +1024,7 @@
 		>;
 	};
 
-	pinctrl_gpio_bl_on: gpioblon {
+	pinctrl_gpio_bl_on: gpioblongrp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_DA13__GPIO3_IO13 0x1b0b0
 		>;
@@ -745,7 +1169,7 @@
 		>;
 	};
 
-	pinctrl_mmc_cd: gpiommccdgrp {
+	pinctrl_mmc_cd: mmccdgrp {
 		fsl,pins = <
 			 /* MMC1 CD */
 			MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x000b0
@@ -776,41 +1200,47 @@
 		>;
 	};
 
-	pinctrl_regulator_usbh_pwr: gpioregusbhpwrgrp {
+	pinctrl_regulator_usbh_pwr: regusbhpwrgrp {
 		fsl,pins = <
 			/* USBH_EN */
 			MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x0f058
 		>;
 	};
 
-	pinctrl_regulator_usbhub_pwr: gpioregusbhubpwrgrp {
+	pinctrl_regulator_usbhub_pwr: regusbhubpwrgrp {
 		fsl,pins = <
 			/* USBH_HUB_EN */
 			MX6QDL_PAD_EIM_D28__GPIO3_IO28 0x0f058
 		>;
 	};
 
-	pinctrl_regulator_usbotg_pwr: gpioregusbotgpwrgrp {
+	pinctrl_regulator_usbotg_pwr: regusbotgpwrgrp {
 		fsl,pins = <
 			/* USBO1 power en */
 			MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x0f058
 		>;
 	};
 
-	pinctrl_reset_moci: gpioresetmocigrp {
+	pinctrl_reset_moci: resetmocigrp {
 		fsl,pins = <
 			/* RESET_MOCI control */
 			MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x0f058
 		>;
 	};
 
-	pinctrl_sd_cd: gpiosdcdgrp {
+	pinctrl_sd_cd: sdcdgrp {
 		fsl,pins = <
 			/* SD1 CD */
 			MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x000b0
 		>;
 	};
 
+	pinctrl_sgtl5000: sgtl5000grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__CCM_CLKO1	0x130b0
+		>;
+	};
+
 	pinctrl_spdif: spdifgrp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_16__SPDIF_IN  0x1b0b0
@@ -818,13 +1248,22 @@
 		>;
 	};
 
-	pinctrl_touch_int: gpiotouchintgrp {
+	pinctrl_touch_int: touchintgrp {
 		fsl,pins = <
 			/* STMPE811 interrupt */
 			MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0
 		>;
 	};
 
+	/* Additional DTR, DSR, DCD */
+	pinctrl_uart1_ctrl: uart1ctrlgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D23__UART1_DCD_B 0x1b0b0
+			MX6QDL_PAD_EIM_D24__UART1_DTR_B 0x1b0b0
+			MX6QDL_PAD_EIM_D25__UART1_DSR_B 0x1b0b0
+		>;
+	};
+
 	pinctrl_uart1_dce: uart1dcegrp {
 		fsl,pins = <
 			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
@@ -842,15 +1281,6 @@
 		>;
 	};
 
-	/* Additional DTR, DSR, DCD */
-	pinctrl_uart1_ctrl: uart1ctrlgrp {
-		fsl,pins = <
-			MX6QDL_PAD_EIM_D23__UART1_DCD_B 0x1b0b0
-			MX6QDL_PAD_EIM_D24__UART1_DTR_B 0x1b0b0
-			MX6QDL_PAD_EIM_D25__UART1_DSR_B 0x1b0b0
-		>;
-	};
-
 	pinctrl_uart2_dce: uart2dcegrp {
 		fsl,pins = <
 			MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA	0x1b0b1
@@ -904,7 +1334,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_4bit: usdhc1grp_4bit {
+	pinctrl_usdhc1_4bit: usdhc1-4bitgrp {
 		fsl,pins = <
 			MX6QDL_PAD_SD1_CMD__SD1_CMD    0x17071
 			MX6QDL_PAD_SD1_CLK__SD1_CLK    0x10071
@@ -915,7 +1345,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_8bit: usdhc1grp_8bit {
+	pinctrl_usdhc1_8bit: usdhc1-8bitgrp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D0__SD1_DATA4 0x17071
 			MX6QDL_PAD_NANDF_D1__SD1_DATA5 0x17071
diff --git a/arch/arm/boot/dts/imx6qdl-apf6.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-apf6.dtsi
index b78ed7974ea9..b78ed7974ea9 100644
--- a/arch/arm/boot/dts/imx6qdl-apf6.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-apf6.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-apf6dev.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-apf6dev.dtsi
index 2577eb4f535a..9e97ef5e43f2 100644
--- a/arch/arm/boot/dts/imx6qdl-apf6dev.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-apf6dev.dtsi
@@ -13,7 +13,7 @@
 
 	backlight: backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm3 0 191000>;
+		pwms = <&pwm3 0 191000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <0>;
 		power-supply = <&reg_5v>;
@@ -121,11 +121,16 @@
 		mux-ext-port = <3>;
 	};
 
+	spdif_out: spdif-out {
+		compatible = "linux,spdif-dit";
+		#sound-dai-cells = <0>;
+	};
+
 	sound-spdif {
 		compatible = "fsl,imx-audio-spdif";
 		model = "imx-spdif";
-		spdif-controller = <&spdif>;
-		spdif-out;
+		audio-cpu = <&spdif>;
+		audio-codec = <&spdif_out>;
 	};
 };
 
@@ -181,6 +186,7 @@
 	codec: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
 		VDDA-supply = <&reg_3p3v>;
 		VDDIO-supply = <&reg_3p3v>;
@@ -211,7 +217,6 @@
 };
 
 &pwm3 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-aristainetos.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-aristainetos.dtsi
new file mode 100644
index 000000000000..acb404c6828b
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-aristainetos.dtsi
@@ -0,0 +1,406 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * support fot the imx6 based aristainetos board
+ *
+ * Copyright (C) 2014 Heiko Schocher <hs@denx.de>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+
+	reg_2p5v: regulator-2p5v {
+		compatible = "regulator-fixed";
+		regulator-name = "2P5V";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_usbh1_vbus: regulator-usbh1-vbus {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_aristainetos_usbh1_vbus>;
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_usbotg_vbus: regulator-usbotg-vbus {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_aristainetos_usbotg_vbus>;
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	tmp103: tmp103@71 {
+		compatible = "ti,tmp103";
+		reg = <0x71>;
+	};
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	rtc@68 {
+		compatible = "dallas,m41t00";
+		reg = <0x68>;
+	};
+};
+
+&ecspi4 {
+	cs-gpios = <&gpio3 20 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi4>;
+	status = "okay";
+
+	flash: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "micron,n25q128a11", "jedec,spi-nor";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rmii";
+	phy-reset-gpios = <&gpio3 29 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	status = "okay";
+};
+
+&pcie {
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usbh1_vbus>;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usbotg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	disable-over-current;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	vmmc-supply = <&reg_3p3v>;
+	cd-gpios = <&gpio4 7 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	vmmc-supply = <&reg_3p3v>;
+	cd-gpios = <&gpio4 8 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog &pinctrl_gpio>;
+
+	pinctrl_aristainetos_usbh1_vbus: aristainetos-usbh1-vbusgrp {
+		fsl,pins = <MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x130b0>;
+	};
+
+	pinctrl_aristainetos_usbotg_vbus: aristainetos-usbotg-vbusgrp {
+		fsl,pins = <MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x130b0>;
+	};
+
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD  0x1b0b0
+			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC  0x1b0b0
+			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD  0x1b0b0
+			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x1b0b0
+		>;
+	};
+
+	pinctrl_backlight: backlightgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__PWM1_OUT	0x1b0b0
+			MX6QDL_PAD_SD4_DAT1__PWM3_OUT	0x1b0b0
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02	0x1b0b0
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
+			MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
+			MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
+			MX6QDL_PAD_EIM_D24__GPIO3_IO24  0x100b1
+		>;
+	};
+
+	pinctrl_ecspi4: ecspi4grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__ECSPI4_SCLK 0x100b1
+			MX6QDL_PAD_EIM_D22__ECSPI4_MISO 0x100b1
+			MX6QDL_PAD_EIM_D28__ECSPI4_MOSI 0x100b1
+			MX6QDL_PAD_EIM_D20__GPIO3_IO20  0x100b1
+			MX6QDL_PAD_SD4_DAT7__GPIO2_IO15 0x1b0b0 /* WP pin */
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO  0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC    0x1b0b0
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN   0x1b0b0
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER   0x1b0b0
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN  0x1b0b0
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX	0x1b0b0
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b0
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT0__FLEXCAN2_TX	0x1b0b0
+			MX6QDL_PAD_SD3_DAT1__FLEXCAN2_RX	0x1b0b0
+			>;
+	};
+
+	pinctrl_gpio: gpiogrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT2__GPIO2_IO10	0x1b0b0
+			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11	0x1b0b0
+			MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0
+			MX6QDL_PAD_SD4_DAT5__GPIO2_IO13	0x1b0b0
+			MX6QDL_PAD_GPIO_3__GPIO1_IO03	0x1b0b0
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04	0x1b0b0
+			MX6QDL_PAD_GPIO_5__GPIO1_IO05	0x1b0b0
+			MX6QDL_PAD_GPIO_6__GPIO1_IO06	0x1b0b0
+			MX6QDL_PAD_GPIO_7__GPIO1_IO07	0x1b0b0
+			MX6QDL_PAD_GPIO_8__GPIO1_IO08	0x1b0b0
+			MX6QDL_PAD_KEY_COL0__GPIO4_IO06	0x1b0b0
+		>;
+	};
+
+	pinctrl_gpmi_nand: gpminandgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CLE__NAND_CLE     0xb0b1
+			MX6QDL_PAD_NANDF_ALE__NAND_ALE     0xb0b1
+			MX6QDL_PAD_NANDF_WP_B__NAND_WP_B   0xb0b1
+			MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+			MX6QDL_PAD_NANDF_CS0__NAND_CE0_B   0xb0b1
+			MX6QDL_PAD_NANDF_CS1__NAND_CE1_B   0xb0b1
+			MX6QDL_PAD_SD4_CMD__NAND_RE_B      0xb0b1
+			MX6QDL_PAD_SD4_CLK__NAND_WE_B      0xb0b1
+			MX6QDL_PAD_NANDF_D0__NAND_DATA00   0xb0b1
+			MX6QDL_PAD_NANDF_D1__NAND_DATA01   0xb0b1
+			MX6QDL_PAD_NANDF_D2__NAND_DATA02   0xb0b1
+			MX6QDL_PAD_NANDF_D3__NAND_DATA03   0xb0b1
+			MX6QDL_PAD_NANDF_D4__NAND_DATA04   0xb0b1
+			MX6QDL_PAD_NANDF_D5__NAND_DATA05   0xb0b1
+			MX6QDL_PAD_NANDF_D6__NAND_DATA06   0xb0b1
+			MX6QDL_PAD_NANDF_D7__NAND_DATA07   0xb0b1
+			MX6QDL_PAD_SD4_DAT0__NAND_DQS      0x00b1
+		>;
+	};
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D29__GPIO3_IO29   0x10
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1
+			MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
+		>;
+	};
+
+	pinctrl_ipu_disp: ipudisp1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x10
+			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15		0x10
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x10
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x10
+			MX6QDL_PAD_DI0_PIN4__GPIO4_IO20			0x20000
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x10
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x10
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x10
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x10
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x10
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x10
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x10
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x10
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x10
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x10
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x10
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x10
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x10
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x10
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x10
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x10
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x10
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x10
+			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18	0x10
+			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19	0x10
+			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20	0x10
+			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21	0x10
+			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22	0x10
+			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23	0x10
+			>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1
+			MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x1b0b1
+			MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x1b0b1
+			MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B 0x1b0b1
+			MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B 0x1b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT14__UART5_TX_DATA 0x1b0b1
+			MX6QDL_PAD_CSI0_DAT15__UART5_RX_DATA 0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD    0x17059
+			MX6QDL_PAD_SD1_CLK__SD1_CLK    0x10059
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
+			MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD    0x17059
+			MX6QDL_PAD_SD2_CLK__SD2_CLK    0x10059
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059
+			MX6QDL_PAD_KEY_COL1__GPIO4_IO08 0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-aristainetos2.dtsi
index 563bf9d44fe0..01d4ea20b13d 100644
--- a/arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-aristainetos2.dtsi
@@ -1,44 +1,8 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
 /*
  * support for the imx6 based aristainetos2 board
  *
  * Copyright (C) 2015 Heiko Schocher <hs@denx.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/imx6qdl-clock.h>
@@ -46,7 +10,7 @@
 / {
 	backlight: backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 		enable-gpios = <&gpio6 31 GPIO_ACTIVE_HIGH>;
@@ -131,7 +95,7 @@
 	pinctrl-0 = <&pinctrl_ecspi4>;
 	status = "okay";
 
-	flash: m25p80@1 {
+	flash: flash@1 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q128a11", "jedec,spi-nor";
@@ -150,116 +114,118 @@
 		reg = <0x58>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <04 0x8>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
 
 		regulators {
 			bcore1 {
 				regulator-name = "bcore1";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			bcore2 {
 				regulator-name = "bcore2";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			bpro {
 				regulator-name = "bpro";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			bperi {
 				regulator-name = "bperi";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			bmem {
 				regulator-name = "bmem";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo2 {
 				regulator-name = "ldo2";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <1800000>;
 			};
 
 			ldo3 {
 				regulator-name = "ldo3";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo4 {
 				regulator-name = "ldo4";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo5 {
 				regulator-name = "ldo5";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo6 {
 				regulator-name = "ldo6";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo7 {
 				regulator-name = "ldo7";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo8 {
 				regulator-name = "ldo8";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo9 {
 				regulator-name = "ldo9";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo10 {
 				regulator-name = "ldo10";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo11 {
 				regulator-name = "ldo11";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			bio {
 				regulator-name = "bio";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
 			};
@@ -301,12 +267,12 @@
 	pinctrl-0 = <&pinctrl_i2c4>;
 	status = "okay";
 
-	eeprom@50{
+	eeprom@50 {
 		compatible = "atmel,24c64";
 		reg = <0x50>;
 	};
 
-	eeprom@57{
+	eeprom@57 {
 		compatible = "atmel,24c64";
 		reg = <0x57>;
 	};
@@ -324,8 +290,9 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		ethphy: ethernet-phy {
+		ethphy: ethernet-phy@0 {
 			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
 			txd0-skew-ps = <0>;
 			txd1-skew-ps = <0>;
 			txd2-skew-ps = <0>;
@@ -346,7 +313,6 @@
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
@@ -414,7 +380,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_gpio>;
 
-	pinctrl_audmux: audmux {
+	pinctrl_audmux: audmuxgrp {
 		fsl,pins = <
 			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD  0x1b0b0
 			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC  0x1b0b0
@@ -507,7 +473,7 @@
 		>;
 	};
 
-	pinctrl_gpmi_nand: gpmi-nand {
+	pinctrl_gpmi_nand: gpminandgrp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_CLE__NAND_CLE     0xb0b1
 			MX6QDL_PAD_NANDF_ALE__NAND_ALE     0xb0b1
@@ -600,11 +566,11 @@
 		>;
 	};
 
-	pinctrl_aristainetos2_usbh1_vbus: aristainetos-usbh1-vbus {
+	pinctrl_aristainetos2_usbh1_vbus: aristainetos-usbh1-vbusgrp {
 		fsl,pins = <MX6QDL_PAD_GPIO_0__USB_H1_PWR 0x130b0>;
 	};
 
-	pinctrl_aristainetos2_usbotg_vbus: aristainetos-usbotg-vbus {
+	pinctrl_aristainetos2_usbotg_vbus: aristainetos-usbotg-vbusgrp {
 		fsl,pins = <MX6QDL_PAD_KEY_ROW4__USB_OTG_PWR 0x130b0>;
 	};
 
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-colibri-v1.2.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-colibri-v1.2.dtsi
new file mode 100644
index 000000000000..d11bf911b728
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-colibri-v1.2.dtsi
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/* Copyright (c) 2025 Toradex */
+
+&i2c2 {
+	/delete-node/ stmpe811@41;
+
+	ad7879_ts: touchscreen@2c {
+		compatible = "adi,ad7879-1";
+		reg = <0x2c>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touch_int>;
+		interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio6>;
+		touchscreen-max-pressure = <4096>;
+		adi,resistance-plate-x = <120>;
+		adi,first-conversion-delay = /bits/ 8 <3>;
+		adi,acquisition-time = /bits/ 8 <1>;
+		adi,median-filter-size = /bits/ 8 <2>;
+		adi,averaging = /bits/ 8 <1>;
+		adi,conversion-interval = /bits/ 8 <255>;
+	};
+
+	tla2024_adc: adc@49 {
+		compatible = "ti,tla2024";
+		reg = <0x49>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Colibri AIN0 */
+		channel@4 {
+			reg = <4>;
+			ti,datarate = <4>;
+			ti,gain = <1>;
+		};
+
+		/* Colibri AIN1 */
+		channel@5 {
+			reg = <5>;
+			ti,datarate = <4>;
+			ti,gain = <1>;
+		};
+
+		/* Colibri AIN2 */
+		channel@6 {
+			reg = <6>;
+			ti,datarate = <4>;
+			ti,gain = <1>;
+		};
+
+		/* Colibri AIN3 */
+		channel@7 {
+			reg = <7>;
+			ti,datarate = <4>;
+			ti,gain = <1>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/imx6qdl-colibri.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-colibri.dtsi
index 4e2a309c93fa..419d85b5a660 100644
--- a/arch/arm/boot/dts/imx6qdl-colibri.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-colibri.dtsi
@@ -1,23 +1,103 @@
 // SPDX-License-Identifier: GPL-2.0+ OR MIT
 /*
- * Copyright 2014-2020 Toradex
+ * Copyright 2014-2022 Toradex
  * Copyright 2012 Freescale Semiconductor, Inc.
  * Copyright 2011 Linaro Ltd.
  */
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
 
 / {
 	model = "Toradex Colibri iMX6DL/S Module";
-	compatible = "toradex,colibri_imx6dl", "fsl,imx6dl";
+
+	aliases {
+		mmc0 = &usdhc3; /* eMMC */
+		mmc1 = &usdhc1; /* MMC/SD Slot */
+		/delete-property/ mmc2;
+		/delete-property/ mmc3;
+	};
 
 	backlight: backlight {
 		compatible = "pwm-backlight";
+		brightness-levels = <0 45 63 88 119 158 203 255>;
+		default-brightness-level = <4>;
+		enable-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* Colibri BL_ON */
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_bl_on>;
-		pwms = <&pwm3 0 5000000>;
-		enable-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* Colibri BL_ON */
+		power-supply = <&reg_module_3v3>;
+		pwms = <&pwm3 0 5000000 PWM_POLARITY_INVERTED>;
+		status = "disabled";
+	};
+
+	extcon_usbc_det: usbc-det {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpios = <&gpio7 12 GPIO_ACTIVE_HIGH>; /* SODIMM 137 / USBC_DET */
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbc_det>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		key-wakeup {
+			debounce-interval = <10>;
+			gpios = <&gpio2 22 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* SODIMM 45 */
+			label = "Wake-Up";
+			linux,code = <KEY_WAKEUP>;
+			wakeup-source;
+		};
+	};
+
+	lcd_display: disp0 {
+		compatible = "fsl,imx-parallel-display";
+		interface-pix-fmt = "bgr666";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu1_lcdif>;
+		status = "disabled";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			lcd_display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			lcd_display_out: endpoint {
+				remote-endpoint = <&lcd_panel_in>;
+			};
+		};
+	};
+
+	/* Will be filled by the bootloader */
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0>;
+	};
+
+	panel_dpi: panel-dpi {
+		/*
+		 * edt,et057090dhu: EDT 5.7" LCD TFT
+		 * edt,et070080dh6: EDT 7.0" LCD TFT
+		 */
+		compatible = "edt,et057090dhu";
+		backlight = <&backlight>;
 		status = "disabled";
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
 	};
 
 	reg_module_3v3: regulator-module-3v3 {
@@ -38,36 +118,45 @@
 
 	reg_usb_host_vbus: regulator-usb-host-vbus {
 		compatible = "regulator-fixed";
+		gpio = <&gpio3 31 GPIO_ACTIVE_LOW>; /* SODIMM 129 / USBH_PEN */
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_regulator_usbh_pwr>;
-		regulator-name = "usb_host_vbus";
-		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>; /* USBH_PEN */
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb_host_vbus";
 		status = "disabled";
 	};
 
 	sound {
 		compatible = "fsl,imx-audio-sgtl5000";
-		model = "imx6dl-colibri-sgtl5000";
-		ssi-controller = <&ssi1>;
 		audio-codec = <&codec>;
 		audio-routing =
 			"Headphone Jack", "HP_OUT",
 			"LINE_IN", "Line In Jack",
 			"MIC_IN", "Mic Jack",
 			"Mic Jack", "Mic Bias";
+		model = "colibri-imx6";
 		mux-int-port = <1>;
 		mux-ext-port = <5>;
+		ssi-controller = <&ssi1>;
+	};
+
+	spdif_out: spdif-out {
+		compatible = "linux,spdif-dit";
+		#sound-dai-cells = <0>;
+	};
+
+	spdif_in: spdif-in {
+		compatible = "linux,spdif-dir";
+		#sound-dai-cells = <0>;
 	};
 
 	/* Optional S/PDIF in on SODIMM 88 and out on SODIMM 90, 137 or 168 */
 	sound_spdif: sound-spdif {
 		compatible = "fsl,imx-audio-spdif";
+		audio-cpu = <&spdif>;
+		audio-codec = <&spdif_out>, <&spdif_in>;
 		model = "imx-spdif";
-		spdif-controller = <&spdif>;
-		spdif-in;
-		spdif-out;
 		status = "disabled";
 	};
 };
@@ -92,6 +181,10 @@
 	status = "disabled";
 };
 
+&clks {
+	fsl,pmic-stby-poweroff;
+};
+
 /* Colibri SSP */
 &ecspi4 {
 	cs-gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
@@ -101,10 +194,10 @@
 };
 
 &fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rmii";
 	phy-handle = <&ethphy>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
 	status = "okay";
 
 	mdio {
@@ -118,6 +211,224 @@
 	};
 };
 
+&gpio1 {
+	gpio-line-names = "",
+			  "SODIMM_67",
+			  "SODIMM_180",
+			  "SODIMM_196",
+			  "SODIMM_174",
+			  "SODIMM_176",
+			  "SODIMM_194",
+			  "SODIMM_55",
+			  "SODIMM_63",
+			  "SODIMM_28",
+			  "SODIMM_93",
+			  "SODIMM_69",
+			  "SODIMM_99",
+			  "SODIMM_130",
+			  "SODIMM_106",
+			  "SODIMM_98",
+			  "SODIMM_192",
+			  "SODIMM_49",
+			  "SODIMM_190",
+			  "SODIMM_51",
+			  "SODIMM_47",
+			  "SODIMM_53",
+			  "",
+			  "SODIMM_22";
+};
+
+&gpio2 {
+	gpio-line-names = "SODIMM_132",
+			  "SODIMM_134",
+			  "SODIMM_135",
+			  "SODIMM_133",
+			  "SODIMM_102",
+			  "SODIMM_43",
+			  "SODIMM_127",
+			  "SODIMM_37",
+			  "SODIMM_104",
+			  "SODIMM_59",
+			  "SODIMM_30",
+			  "SODIMM_100",
+			  "SODIMM_38",
+			  "SODIMM_34",
+			  "SODIMM_32",
+			  "SODIMM_36",
+			  "SODIMM_59",
+			  "SODIMM_67",
+			  "SODIMM_97",
+			  "SODIMM_79",
+			  "SODIMM_103",
+			  "SODIMM_101",
+			  "SODIMM_45",
+			  "SODIMM_105",
+			  "SODIMM_107",
+			  "SODIMM_91",
+			  "SODIMM_89",
+			  "SODIMM_150",
+			  "SODIMM_126",
+			  "SODIMM_128",
+			  "",
+			  "SODIMM_94";
+};
+
+&gpio3 {
+	gpio-line-names = "SODIMM_111",
+			  "SODIMM_113",
+			  "SODIMM_115",
+			  "SODIMM_117",
+			  "SODIMM_119",
+			  "SODIMM_121",
+			  "SODIMM_123",
+			  "SODIMM_125",
+			  "SODIMM_110",
+			  "SODIMM_112",
+			  "SODIMM_114",
+			  "SODIMM_116",
+			  "SODIMM_118",
+			  "SODIMM_120",
+			  "SODIMM_122",
+			  "SODIMM_124",
+			  "",
+			  "SODIMM_96",
+			  "SODIMM_77",
+			  "SODIMM_25",
+			  "SODIMM_27",
+			  "SODIMM_88",
+			  "SODIMM_90",
+			  "SODIMM_31",
+			  "SODIMM_23",
+			  "SODIMM_29",
+			  "SODIMM_71",
+			  "SODIMM_73",
+			  "SODIMM_92",
+			  "SODIMM_81",
+			  "SODIMM_131",
+			  "SODIMM_129";
+};
+
+&gpio4 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_168",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_184",
+			  "SODIMM_186",
+			  "HDMI_15",
+			  "HDMI_16",
+			  "SODIMM_178",
+			  "SODIMM_188",
+			  "SODIMM_56",
+			  "SODIMM_44",
+			  "SODIMM_68",
+			  "SODIMM_82",
+			  "SODIMM_24",
+			  "SODIMM_76",
+			  "SODIMM_70",
+			  "SODIMM_60",
+			  "SODIMM_58",
+			  "SODIMM_78",
+			  "SODIMM_72",
+			  "SODIMM_80",
+			  "SODIMM_46",
+			  "SODIMM_62",
+			  "SODIMM_48",
+			  "SODIMM_74";
+};
+
+&gpio5 {
+	gpio-line-names = "SODIMM_95",
+			  "",
+			  "SODIMM_86",
+			  "",
+			  "SODIMM_65",
+			  "SODIMM_50",
+			  "SODIMM_52",
+			  "SODIMM_54",
+			  "SODIMM_66",
+			  "SODIMM_64",
+			  "SODIMM_57",
+			  "SODIMM_61",
+			  "SODIMM_136",
+			  "SODIMM_138",
+			  "SODIMM_140",
+			  "SODIMM_142",
+			  "SODIMM_144",
+			  "SODIMM_146",
+			  "SODIMM_172",
+			  "SODIMM_170",
+			  "SODIMM_149",
+			  "SODIMM_151",
+			  "SODIMM_153",
+			  "SODIMM_155",
+			  "SODIMM_157",
+			  "SODIMM_159",
+			  "SODIMM_161",
+			  "SODIMM_163",
+			  "SODIMM_33",
+			  "SODIMM_35",
+			  "SODIMM_165",
+			  "SODIMM_167";
+};
+
+&gpio6 {
+	gpio-line-names = "SODIMM_169",
+			  "SODIMM_171",
+			  "SODIMM_173",
+			  "SODIMM_175",
+			  "SODIMM_177",
+			  "SODIMM_179",
+			  "SODIMM_85",
+			  "SODIMM_166",
+			  "SODIMM_160",
+			  "SODIMM_162",
+			  "SODIMM_158",
+			  "SODIMM_164",
+			  "",
+			  "",
+			  "SODIMM_156",
+			  "SODIMM_75",
+			  "SODIMM_154",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_152";
+};
+
+&gpio7 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_19",
+			  "SODIMM_21",
+			  "",
+			  "SODIMM_137";
+};
+
 &hdmi {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hdmi_ddc>;
@@ -132,65 +443,66 @@
 	clock-frequency = <100000>;
 	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c2>;
-	pinctrl-0 = <&pinctrl_i2c2_gpio>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
 	scl-gpios = <&gpio2 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	sda-gpios = <&gpio3 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
+		fsl,pmic-stby-poweroff;
 		reg = <0x08>;
 
 		regulators {
 			sw1a_reg: sw1ab {
-				regulator-min-microvolt = <300000>;
-				regulator-max-microvolt = <1875000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1875000>;
+				regulator-min-microvolt = <300000>;
 				regulator-ramp-delay = <6250>;
 			};
 
 			sw1c_reg: sw1c {
-				regulator-min-microvolt = <300000>;
-				regulator-max-microvolt = <1875000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1875000>;
+				regulator-min-microvolt = <300000>;
 				regulator-ramp-delay = <6250>;
 			};
 
 			sw3a_reg: sw3a {
-				regulator-min-microvolt = <400000>;
-				regulator-max-microvolt = <1975000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1975000>;
+				regulator-min-microvolt = <400000>;
 			};
 
 			swbst_reg: swbst {
-				regulator-min-microvolt = <5000000>;
-				regulator-max-microvolt = <5150000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <5150000>;
+				regulator-min-microvolt = <5000000>;
 			};
 
 			snvs_reg: vsnvs {
-				regulator-min-microvolt = <1000000>;
-				regulator-max-microvolt = <3000000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3000000>;
+				regulator-min-microvolt = <1000000>;
 			};
 
 			vref_reg: vrefddr {
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
 			};
 
 			/* vgen1: unused */
 
 			vgen2_reg: vgen2 {
-				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <1550000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1550000>;
+				regulator-min-microvolt = <800000>;
 			};
 
 			/*
@@ -198,57 +510,59 @@
 			 * the i.MX 6 NVCC_SD1.
 			 */
 			vgen3_reg: vgen3 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
 			};
 
 			vgen4_reg: vgen4 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
 			};
 
 			vgen5_reg: vgen5 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
 			};
 
 			vgen6_reg: vgen6 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
 			};
 		};
 	};
 
 	codec: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
-		reg = <0x0a>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
+		lrclk-strength = <3>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sgtl5000>;
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		VDDA-supply = <&reg_module_3v3_audio>;
 		VDDIO-supply = <&reg_module_3v3>;
 		VDDD-supply = <&vgen4_reg>;
-		lrclk-strength = <3>;
 	};
 
 	/* STMPE811 touch screen controller */
 	stmpe811@41 {
 		compatible = "st,stmpe811";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_touch_int>;
-		reg = <0x41>;
+		blocks = <0x5>;
 		interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-parent = <&gpio6>;
-		interrupt-controller;
 		id = <0>;
-		blocks = <0x5>;
 		irq-trigger = <0x1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touch_int>;
+		reg = <0x41>;
 		/* 3.25 MHz ADC clock speed */
 		st,adc-freq = <1>;
 		/* 12-bit ADC */
@@ -258,7 +572,7 @@
 		/* ADC converstion time: 80 clocks */
 		st,sample-time = <4>;
 
-		stmpe_touchscreen {
+		stmpe_ts: touchscreen {
 			compatible = "st,stmpe-ts";
 			/* 8 sample average control */
 			st,ave-ctrl = <3>;
@@ -275,7 +589,7 @@
 			st,touch-det-delay = <5>;
 		};
 
-		stmpe_adc {
+		stmpe_adc: stmpe_adc {
 			compatible = "st,stmpe-adc";
 			/* forbid to use ADC channels 3-0 (touch) */
 			st,norequest-mask = <0x0F>;
@@ -294,6 +608,21 @@
 	scl-gpios = <&gpio1 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "disabled";
+
+	atmel_mxt_ts: touchscreen@4a {
+		compatible = "atmel,maxtouch";
+		interrupt-parent = <&gpio2>;
+		interrupts = <24 IRQ_TYPE_EDGE_FALLING>;	/* SODIMM 107 */
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_atmel_conn>;
+		reg = <0x4a>;
+		reset-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;	/* SODIMM 106 */
+		status = "disabled";
+	};
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&lcd_display_in>;
 };
 
 /* Colibri PWM<B> */
@@ -312,7 +641,6 @@
 
 /* Colibri PWM<A> */
 &pwm3 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "disabled";
@@ -338,56 +666,66 @@
 
 /* Colibri UART_A */
 &uart1 {
+	fsl,dte-mode;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1_dte &pinctrl_uart1_ctrl>;
-	fsl,dte-mode;
 	uart-has-rtscts;
 	status = "disabled";
 };
 
 /* Colibri UART_B */
 &uart2 {
+	fsl,dte-mode;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart2_dte>;
-	fsl,dte-mode;
 	uart-has-rtscts;
 	status = "disabled";
 };
 
 /* Colibri UART_C */
 &uart3 {
+	fsl,dte-mode;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart3_dte>;
-	fsl,dte-mode;
 	status = "disabled";
 };
 
+/* Colibri USBH */
+&usbh1 {
+	vbus-supply = <&reg_usb_host_vbus>;
+};
+
+/* Colibri USBC */
 &usbotg {
-	disable-over-current;
-	dr_mode = "peripheral";
+	dr_mode = "otg";
+	extcon = <0>, <&extcon_usbc_det>;
 	status = "disabled";
 };
 
 /* Colibri MMC */
 &usdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_mmc_cd>;
 	cd-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; /* MMCD */
-	disable-wp;
-	vqmmc-supply = <&reg_module_3v3>;
 	bus-width = <4>;
 	no-1-8-v;
+	disable-wp;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_mmc_cd>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz &pinctrl_mmc_cd>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz &pinctrl_mmc_cd>;
+	pinctrl-3 = <&pinctrl_usdhc1_sleep &pinctrl_mmc_cd_sleep>;
+	vmmc-supply = <&reg_module_3v3>;
+	vqmmc-supply = <&vgen3_reg>;
 	status = "disabled";
 };
 
 /* eMMC */
 &usdhc3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc3>;
-	vqmmc-supply = <&reg_module_3v3>;
 	bus-width = <8>;
 	no-1-8-v;
 	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	vqmmc-supply = <&reg_module_3v3>;
 	status = "okay";
 };
 
@@ -405,14 +743,34 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usbh_oc_1>;
 
+	/* Atmel MXT touchsceen + Capacitive Touch Adapter */
+	/* NOTE: This pin group conflicts with pin groups
+	 * pinctrl_pwm1/pinctrl_pwm4. Don't use them simultaneously.
+	 */
+	pinctrl_atmel_adap: atmeladaptergrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__GPIO1_IO09   0xb0b1  /* SODIMM  28 */
+			MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0xb0b1  /* SODIMM  30 */
+		>;
+	};
+
+	/* Atmel MXT touchsceen + boards with built-in Capacitive Touch Connector */
+	/* NOTE: This pin group conflicts with pin groups pinctrl_weim_cs1 and
+	 * pinctrl_weim_cs2. Don't use them simultaneously.
+	 */
+	pinctrl_atmel_conn: atmelconnectorgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_CS1__GPIO2_IO24  0xb0b1  /* SODIMM_107 */
+			MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0xb0b1  /* SODIMM_106 */
+		>;
+	};
+
 	pinctrl_audmux: audmuxgrp {
 		fsl,pins = <
 			MX6QDL_PAD_KEY_COL0__AUD5_TXC	0x130b0
 			MX6QDL_PAD_KEY_ROW0__AUD5_TXD	0x130b0
 			MX6QDL_PAD_KEY_COL1__AUD5_TXFS	0x130b0
 			MX6QDL_PAD_KEY_ROW1__AUD5_RXD	0x130b0
-			/* SGTL5000 sys_mclk */
-			MX6QDL_PAD_GPIO_0__CCM_CLKO1	0x000b0
 		>;
 	};
 
@@ -423,28 +781,52 @@
 		>;
 	};
 
+	/* CSI pins used as GPIOs */
+	pinctrl_csi_gpio_1: csigpio1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D18__GPIO3_IO18   0x1b0b0
+			MX6QDL_PAD_EIM_A19__GPIO2_IO19   0x1b0b0
+			MX6QDL_PAD_EIM_D29__GPIO3_IO29   0x130b0
+			MX6QDL_PAD_EIM_A23__GPIO6_IO06   0x1b0b0
+			MX6QDL_PAD_EIM_A20__GPIO2_IO18   0x1b0b0
+			MX6QDL_PAD_EIM_A17__GPIO2_IO21   0x1b0b0
+			MX6QDL_PAD_EIM_A18__GPIO2_IO20   0x1b0b0
+			MX6QDL_PAD_EIM_EB3__GPIO2_IO31   0x1b0b0
+			MX6QDL_PAD_EIM_D17__GPIO3_IO17   0x1b0b0
+			MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x1b0b0
+			MX6QDL_PAD_SD2_CMD__GPIO1_IO11   0x1b0b0
+			MX6QDL_PAD_SD2_DAT0__GPIO1_IO15  0x1b0b0
+		>;
+	};
+
+	pinctrl_csi_gpio_2: csigpio2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A24__GPIO5_IO04   0x1b0b0
+		>;
+	};
+
 	pinctrl_ecspi4: ecspi4grp {
 		fsl,pins = <
+			/* SPI CS */
+			MX6QDL_PAD_EIM_A25__GPIO5_IO02	0x000b1
 			MX6QDL_PAD_EIM_D22__ECSPI4_MISO	0x100b1
 			MX6QDL_PAD_EIM_D28__ECSPI4_MOSI	0x100b1
 			MX6QDL_PAD_EIM_D21__ECSPI4_SCLK 0x100b1
-			/* SPI CS */
-			MX6QDL_PAD_EIM_A25__GPIO5_IO02	0x000b1
 		>;
 	};
 
 	pinctrl_enet: enetgrp {
 		fsl,pins = <
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN	0x1b0b0
 			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
 			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER	0x1b0b0
 			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0	0x1b0b0
 			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1	0x1b0b0
-			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER	0x1b0b0
 			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN	0x1b0b0
 			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0	0x1b0b0
 			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1	0x1b0b0
-			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN	0x1b0b0
-			MX6QDL_PAD_GPIO_16__ENET_REF_CLK     ((1<<30) | 0x1b0b0)
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	((1<<30) | 0x1b0b0)
 		>;
 	};
 
@@ -462,13 +844,32 @@
 		>;
 	};
 
-	pinctrl_gpio_bl_on: gpioblon {
+	pinctrl_gpio_1: gpio1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_PIN4__GPIO4_IO20     0x1b0b0
+			MX6QDL_PAD_EIM_D27__GPIO3_IO27      0x1b0b0
+			MX6QDL_PAD_ENET_REF_CLK__GPIO1_IO23 0x1b0b0
+			MX6QDL_PAD_NANDF_D3__GPIO2_IO03     0x1b0b0
+			MX6QDL_PAD_NANDF_D4__GPIO2_IO04     0x1b0b0
+			MX6QDL_PAD_NANDF_D6__GPIO2_IO06     0x1b0b0
+			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08     0x1b0b0
+			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11     0x1b0b0
+		>;
+	};
+	pinctrl_gpio_2: gpio2grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_7__GPIO1_IO07       0x1b0b0
+			MX6QDL_PAD_GPIO_8__GPIO1_IO08       0x1b0b0
+		>;
+	};
+
+	pinctrl_gpio_bl_on: gpioblongrp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D26__GPIO3_IO26		0x1b0b0
 		>;
 	};
 
-	pinctrl_gpio_keys: gpiokeys {
+	pinctrl_gpio_keys: gpiokeysgrp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_A16__GPIO2_IO22		0x130b0
 		>;
@@ -483,15 +884,15 @@
 
 	pinctrl_i2c2: i2c2grp {
 		fsl,pins = <
-			MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001b8b1
 			MX6QDL_PAD_EIM_D16__I2C2_SDA 0x4001b8b1
+			MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001b8b1
 		>;
 	};
 
-	pinctrl_i2c2_gpio: i2c2grp {
+	pinctrl_i2c2_gpio: i2c2gpiogrp {
 		fsl,pins = <
-			MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x4001b8b1
 			MX6QDL_PAD_EIM_D16__GPIO3_IO16 0x4001b8b1
+			MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x4001b8b1
 		>;
 	};
 
@@ -523,8 +924,8 @@
 			MX6QDL_PAD_EIM_EB3__IPU1_CSI1_HSYNC	0xb0b1
 			MX6QDL_PAD_EIM_D29__IPU1_CSI1_VSYNC	0xb0b1
 			/* Disable PWM pins on camera interface */
-			MX6QDL_PAD_SD4_DAT1__GPIO2_IO09		0x40
 			MX6QDL_PAD_GPIO_1__GPIO1_IO01		0x40
+			MX6QDL_PAD_SD4_DAT1__GPIO2_IO09		0x40
 		>;
 	};
 
@@ -555,19 +956,34 @@
 		>;
 	};
 
-	pinctrl_mic_gnd: gpiomicgnd {
+	pinctrl_lvds_transceiver: lvdstxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_WAIT__GPIO5_IO00 0x03030 /* SODIMM  95 */
+			MX6QDL_PAD_GPIO_7__GPIO1_IO07   0x0b030 /* SODIMM  55 */
+			MX6QDL_PAD_GPIO_8__GPIO1_IO08   0x03030 /* SODIMM  63 */
+			MX6QDL_PAD_SD2_DAT3__GPIO1_IO12 0x03030 /* SODIMM  99 */
+		>;
+	};
+
+	pinctrl_mic_gnd: micgndgrp {
 		fsl,pins = <
 			/* Controls Mic GND, PU or '1' pull Mic GND to GND */
 			MX6QDL_PAD_RGMII_TD1__GPIO6_IO21 0x1b0b0
 		>;
 	};
 
-	pinctrl_mmc_cd: gpiommccd {
+	pinctrl_mmc_cd: mmccdgrp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D5__GPIO2_IO05	0x1b0b1
 		>;
 	};
 
+	pinctrl_mmc_cd_sleep: mmccdslpgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D5__GPIO2_IO05	0x0
+		>;
+	};
+
 	pinctrl_pwm1: pwm1grp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_9__PWM1_OUT	0x1b0b1
@@ -576,15 +992,15 @@
 
 	pinctrl_pwm2: pwm2grp {
 		fsl,pins = <
-			MX6QDL_PAD_GPIO_1__PWM2_OUT	0x1b0b1
 			MX6QDL_PAD_EIM_A21__GPIO2_IO17	0x00040
+			MX6QDL_PAD_GPIO_1__PWM2_OUT	0x1b0b1
 		>;
 	};
 
 	pinctrl_pwm3: pwm3grp {
 		fsl,pins = <
-			MX6QDL_PAD_SD4_DAT1__PWM3_OUT	0x1b0b1
 			MX6QDL_PAD_EIM_A22__GPIO2_IO16	0x00040
+			MX6QDL_PAD_SD4_DAT1__PWM3_OUT	0x1b0b1
 		>;
 	};
 
@@ -596,15 +1012,15 @@
 
 	pinctrl_regulator_usbh_pwr: gpioregusbhpwrgrp {
 		fsl,pins = <
-			/* USBH_EN */
+			/* SODIMM 129 / USBH_PEN */
 			MX6QDL_PAD_EIM_D31__GPIO3_IO31	0x0f058
 		>;
 	};
 
-	pinctrl_usbh_oc_1: usbhoc1grp {
+	pinctrl_sgtl5000: sgtl5000grp {
 		fsl,pins = <
-			/* USBH_OC */
-			MX6QDL_PAD_EIM_D30__GPIO3_IO30		0x1b0b0
+			/* SGTL5000 sys_mclk */
+			MX6QDL_PAD_GPIO_0__CCM_CLKO1	0x000b0
 		>;
 	};
 
@@ -650,9 +1066,9 @@
 	pinctrl_uart2_dte: uart2dtegrp {
 		fsl,pins = <
 			MX6QDL_PAD_SD4_DAT4__UART2_TX_DATA	0x1b0b1
-			MX6QDL_PAD_SD4_DAT7__UART2_RX_DATA	0x1b0b1
-			MX6QDL_PAD_SD4_DAT6__UART2_RTS_B	0x1b0b1
 			MX6QDL_PAD_SD4_DAT5__UART2_CTS_B	0x1b0b1
+			MX6QDL_PAD_SD4_DAT6__UART2_RTS_B	0x1b0b1
+			MX6QDL_PAD_SD4_DAT7__UART2_RX_DATA	0x1b0b1
 		>;
 	};
 
@@ -665,22 +1081,29 @@
 
 	pinctrl_usbc_det: usbcdetgrp {
 		fsl,pins = <
-			/* USBC_DET */
+			/* SODIMM 137 / USBC_DET */
 			MX6QDL_PAD_GPIO_17__GPIO7_IO12		0x1b0b0
-			/* USBC_DET_EN */
-			MX6QDL_PAD_RGMII_TX_CTL__GPIO6_IO26	0x0f058
 			/* USBC_DET_OVERWRITE */
 			MX6QDL_PAD_RGMII_RXC__GPIO6_IO30	0x0f058
+			/* USBC_DET_EN */
+			MX6QDL_PAD_RGMII_TX_CTL__GPIO6_IO26	0x0f058
 		>;
 	};
 
-	pinctrl_usbc_id_1: usbc_id-1 {
+	pinctrl_usbc_id_1: usbcid1grp {
 		fsl,pins = <
 			/* USBC_ID */
 			MX6QDL_PAD_NANDF_D2__GPIO2_IO02		0x1b0b0
 		>;
 	};
 
+	pinctrl_usbh_oc_1: usbhoc1grp {
+		fsl,pins = <
+			/* USBH_OC */
+			MX6QDL_PAD_EIM_D30__GPIO3_IO30		0x1b0b0
+		>;
+	};
+
 	pinctrl_usdhc1: usdhc1grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD1_CMD__SD1_CMD	0x17071
@@ -692,6 +1115,40 @@
 		>;
 	};
 
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD    0x170b1
+			MX6QDL_PAD_SD1_CLK__SD1_CLK    0x100b1
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170b1
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170b1
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170b1
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170b1
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD    0x170f1
+			MX6QDL_PAD_SD1_CLK__SD1_CLK    0x100f1
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f1
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f1
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f1
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f1
+		>;
+	};
+
+	/* avoid backfeeding with removed card power */
+	pinctrl_usdhc1_sleep: usdhc1sleepgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD	0x3000
+			MX6QDL_PAD_SD1_CLK__SD1_CLK	0x3000
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0	0x3000
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1	0x3000
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2	0x3000
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3	0x3000
+		>;
+	};
+
 	pinctrl_usdhc3: usdhc3grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD	0x17059
@@ -730,135 +1187,136 @@
 		>;
 	};
 
-	pinctrl_weim_sram: weimsramgrp {
-		fsl,pins = <
-			MX6QDL_PAD_EIM_OE__EIM_OE_B		0xb0b1
-			MX6QDL_PAD_EIM_RW__EIM_RW		0xb0b1
-			/* Data */
-			MX6QDL_PAD_CSI0_DATA_EN__EIM_DATA00	0x1b0b0
-			MX6QDL_PAD_CSI0_VSYNC__EIM_DATA01	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT4__EIM_DATA02	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT5__EIM_DATA03	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT6__EIM_DATA04	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT7__EIM_DATA05	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT8__EIM_DATA06	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT9__EIM_DATA07	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT12__EIM_DATA08	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT13__EIM_DATA09	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT14__EIM_DATA10	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT15__EIM_DATA11	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT16__EIM_DATA12	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT17__EIM_DATA13	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT18__EIM_DATA14	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT19__EIM_DATA15	0x1b0b0
-			/* Address */
-			MX6QDL_PAD_EIM_DA15__EIM_AD15		0xb0b1
-			MX6QDL_PAD_EIM_DA14__EIM_AD14		0xb0b1
-			MX6QDL_PAD_EIM_DA13__EIM_AD13		0xb0b1
-			MX6QDL_PAD_EIM_DA12__EIM_AD12		0xb0b1
-			MX6QDL_PAD_EIM_DA11__EIM_AD11		0xb0b1
-			MX6QDL_PAD_EIM_DA10__EIM_AD10		0xb0b1
-			MX6QDL_PAD_EIM_DA9__EIM_AD09		0xb0b1
-			MX6QDL_PAD_EIM_DA8__EIM_AD08		0xb0b1
-			MX6QDL_PAD_EIM_DA7__EIM_AD07		0xb0b1
-			MX6QDL_PAD_EIM_DA6__EIM_AD06		0xb0b1
-			MX6QDL_PAD_EIM_DA5__EIM_AD05		0xb0b1
-			MX6QDL_PAD_EIM_DA4__EIM_AD04		0xb0b1
-			MX6QDL_PAD_EIM_DA3__EIM_AD03		0xb0b1
-			MX6QDL_PAD_EIM_DA2__EIM_AD02		0xb0b1
-			MX6QDL_PAD_EIM_DA1__EIM_AD01		0xb0b1
-			MX6QDL_PAD_EIM_DA0__EIM_AD00		0xb0b1
-		>;
-	};
-
-	pinctrl_weim_rdnwr: weimrdnwr {
-		fsl,pins = <
-			MX6QDL_PAD_SD2_CLK__GPIO1_IO10		0x0040
-			MX6QDL_PAD_RGMII_TD3__GPIO6_IO23	0x130b0
-		>;
-	};
-
-	pinctrl_weim_npwe: weimnpwe {
-		fsl,pins = <
-			MX6QDL_PAD_SD2_DAT3__GPIO1_IO12		0x0040
-			MX6QDL_PAD_RGMII_TD2__GPIO6_IO22	0x130b0
-		>;
-	};
-
 	/* ADDRESS[16:18] [25] used as GPIO */
-	pinctrl_weim_gpio_1: weimgpio-1 {
+	pinctrl_weim_gpio_1: weimgpio1grp {
 		fsl,pins = <
-			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b0
-			MX6QDL_PAD_KEY_ROW2__GPIO4_IO11		0x1b0b0
-			MX6QDL_PAD_KEY_COL2__GPIO4_IO10		0x1b0b0
 			MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17	0x1b0b0
 			MX6QDL_PAD_DISP0_DAT22__GPIO5_IO16	0x1b0b0
 			MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15	0x1b0b0
 			MX6QDL_PAD_DISP0_DAT20__GPIO5_IO14	0x1b0b0
 			MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13	0x1b0b0
 			MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12	0x1b0b0
+			MX6QDL_PAD_KEY_COL2__GPIO4_IO10		0x1b0b0
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b0
+			MX6QDL_PAD_KEY_ROW2__GPIO4_IO11		0x1b0b0
 			MX6QDL_PAD_NANDF_D1__GPIO2_IO01		0x1b0b0
 		>;
 	};
 
 	/* ADDRESS[19:24] used as GPIO */
-	pinctrl_weim_gpio_2: weimgpio-2 {
+	pinctrl_weim_gpio_2: weimgpio2grp {
 		fsl,pins = <
-			MX6QDL_PAD_KEY_ROW2__GPIO4_IO11		0x1b0b0
-			MX6QDL_PAD_KEY_COL2__GPIO4_IO10		0x1b0b0
-			MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17	0x1b0b0
-			MX6QDL_PAD_DISP0_DAT22__GPIO5_IO16	0x1b0b0
-			MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15	0x1b0b0
-			MX6QDL_PAD_DISP0_DAT20__GPIO5_IO14	0x1b0b0
-			MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13	0x1b0b0
 			MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12	0x1b0b0
+			MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13	0x1b0b0
+			MX6QDL_PAD_DISP0_DAT20__GPIO5_IO14	0x1b0b0
+			MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15	0x1b0b0
+			MX6QDL_PAD_DISP0_DAT22__GPIO5_IO16	0x1b0b0
+			MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17	0x1b0b0
+			MX6QDL_PAD_KEY_COL2__GPIO4_IO10		0x1b0b0
+			MX6QDL_PAD_KEY_ROW2__GPIO4_IO11		0x1b0b0
 			MX6QDL_PAD_NANDF_D1__GPIO2_IO01		0x1b0b0
 		>;
 	};
 
 	/* DATA[16:31] used as GPIO */
-	pinctrl_weim_gpio_3: weimgpio-3 {
+	pinctrl_weim_gpio_3: weimgpio3grp {
 		fsl,pins = <
+			MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19	0x1b0b0
+			MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18	0x1b0b0
 			MX6QDL_PAD_EIM_LBA__GPIO2_IO27		0x1b0b0
 			MX6QDL_PAD_EIM_BCLK__GPIO6_IO31		0x1b0b0
-			MX6QDL_PAD_NANDF_CS3__GPIO6_IO16	0x1b0b0
-			MX6QDL_PAD_NANDF_CS1__GPIO6_IO14	0x1b0b0
-			MX6QDL_PAD_NANDF_RB0__GPIO6_IO10	0x1b0b0
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1b0b0
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1b0b0
+			MX6QDL_PAD_GPIO_5__GPIO1_IO05		0x1b0b0
+			MX6QDL_PAD_GPIO_19__GPIO4_IO05		0x1b0b0
 			MX6QDL_PAD_NANDF_ALE__GPIO6_IO08	0x1b0b0
-			MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09	0x1b0b0
 			MX6QDL_PAD_NANDF_CS0__GPIO6_IO11	0x1b0b0
+			MX6QDL_PAD_NANDF_CS1__GPIO6_IO14	0x1b0b0
+			MX6QDL_PAD_NANDF_CS3__GPIO6_IO16	0x1b0b0
 			MX6QDL_PAD_NANDF_CLE__GPIO6_IO07	0x1b0b0
-			MX6QDL_PAD_GPIO_19__GPIO4_IO05		0x1b0b0
-			MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19	0x1b0b0
-			MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18	0x1b0b0
-			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1b0b0
-			MX6QDL_PAD_GPIO_5__GPIO1_IO05		0x1b0b0
-			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1b0b0
+			MX6QDL_PAD_NANDF_RB0__GPIO6_IO10	0x1b0b0
+			MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09	0x1b0b0
 		>;
 	};
 
 	/* DQM[0:3] used as GPIO */
-	pinctrl_weim_gpio_4: weimgpio-4 {
+	pinctrl_weim_gpio_4: weimgpio4grp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_EB0__GPIO2_IO28		0x1b0b0
 			MX6QDL_PAD_EIM_EB1__GPIO2_IO29		0x1b0b0
-			MX6QDL_PAD_SD2_DAT2__GPIO1_IO13		0x1b0b0
 			MX6QDL_PAD_NANDF_D0__GPIO2_IO00		0x1b0b0
+			MX6QDL_PAD_SD2_DAT2__GPIO1_IO13		0x1b0b0
 		>;
 	};
 
 	/* RDY used as GPIO */
-	pinctrl_weim_gpio_5: weimgpio-5 {
+	pinctrl_weim_gpio_5: weimgpio5grp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_WAIT__GPIO5_IO00		0x1b0b0
 		>;
 	};
 
 	/* ADDRESS[16] DATA[30] used as GPIO */
-	pinctrl_weim_gpio_6: weimgpio-6 {
+	pinctrl_weim_gpio_6: weimgpio6grp {
 		fsl,pins = <
-			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b0
 			MX6QDL_PAD_KEY_COL4__GPIO4_IO14		0x1b0b0
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b0
+		>;
+	};
+
+	pinctrl_weim_npwe: weimnpwegrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_TD2__GPIO6_IO22	0x130b0
+			MX6QDL_PAD_SD2_DAT3__GPIO1_IO12		0x0040
+		>;
+	};
+
+	pinctrl_weim_sram: weimsramgrp {
+		fsl,pins = <
+			/* Data */
+			MX6QDL_PAD_CSI0_DAT4__EIM_DATA02	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT5__EIM_DATA03	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT6__EIM_DATA04	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT7__EIM_DATA05	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT8__EIM_DATA06	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT9__EIM_DATA07	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT12__EIM_DATA08	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT13__EIM_DATA09	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT14__EIM_DATA10	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT15__EIM_DATA11	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT16__EIM_DATA12	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT17__EIM_DATA13	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT18__EIM_DATA14	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT19__EIM_DATA15	0x1b0b0
+			MX6QDL_PAD_CSI0_DATA_EN__EIM_DATA00	0x1b0b0
+			MX6QDL_PAD_CSI0_VSYNC__EIM_DATA01	0x1b0b0
+			/* Address */
+			MX6QDL_PAD_EIM_DA0__EIM_AD00		0xb0b1
+			MX6QDL_PAD_EIM_DA1__EIM_AD01		0xb0b1
+			MX6QDL_PAD_EIM_DA2__EIM_AD02		0xb0b1
+			MX6QDL_PAD_EIM_DA3__EIM_AD03		0xb0b1
+			MX6QDL_PAD_EIM_DA4__EIM_AD04		0xb0b1
+			MX6QDL_PAD_EIM_DA5__EIM_AD05		0xb0b1
+			MX6QDL_PAD_EIM_DA6__EIM_AD06		0xb0b1
+			MX6QDL_PAD_EIM_DA7__EIM_AD07		0xb0b1
+			MX6QDL_PAD_EIM_DA8__EIM_AD08		0xb0b1
+			MX6QDL_PAD_EIM_DA9__EIM_AD09		0xb0b1
+			MX6QDL_PAD_EIM_DA10__EIM_AD10		0xb0b1
+			MX6QDL_PAD_EIM_DA11__EIM_AD11		0xb0b1
+			MX6QDL_PAD_EIM_DA12__EIM_AD12		0xb0b1
+			MX6QDL_PAD_EIM_DA13__EIM_AD13		0xb0b1
+			MX6QDL_PAD_EIM_DA14__EIM_AD14		0xb0b1
+			MX6QDL_PAD_EIM_DA15__EIM_AD15		0xb0b1
+			/* Ctrl */
+			MX6QDL_PAD_EIM_OE__EIM_OE_B		0xb0b1
+			MX6QDL_PAD_EIM_RW__EIM_RW		0xb0b1
+		>;
+	};
+
+	pinctrl_weim_rdnwr: weimrdnwrgrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_TD3__GPIO6_IO23	0x130b0
+			MX6QDL_PAD_SD2_CLK__GPIO1_IO10		0x0040
 		>;
 	};
 };
diff --git a/arch/arm/boot/dts/imx6qdl-cubox-i.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-cubox-i.dtsi
index 1e530d892b76..c504cf7e9492 100644
--- a/arch/arm/boot/dts/imx6qdl-cubox-i.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-cubox-i.dtsi
@@ -64,7 +64,7 @@
 			active-low;
 			label = "imx6:red:front";
 			max-brightness = <248>;
-			pwms = <&pwm1 0 50000>;
+			pwms = <&pwm1 0 50000 0>;
 		};
 	};
 
@@ -100,12 +100,17 @@
 		vin-supply = <&v_5v0>;
 	};
 
+	spdif_out: spdif-out {
+		compatible = "linux,spdif-dit";
+		#sound-dai-cells = <0>;
+	};
+
 	sound-spdif {
 		compatible = "fsl,imx-audio-spdif";
 		model = "Integrated SPDIF";
 		/* IMX6 doesn't implement this yet */
-		spdif-controller = <&spdif>;
-		spdif-out;
+		audio-cpu = <&spdif>;
+		audio-codec = <&spdif_out>;
 	};
 
 	gpio-keys {
@@ -113,7 +118,7 @@
 		pinctrl-0 = <&pinctrl_gpio_key>;
 		pinctrl-names = "default";
 
-		button_0 {
+		button-0 {
 			label = "Button 0";
 			gpios = <&gpio3 8 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_0>;
@@ -148,92 +153,89 @@
 };
 
 &iomuxc {
-	cubox_i {
-		pinctrl_cubox_i_hdmi: cubox-i-hdmi {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0
-			>;
-		};
+	pinctrl_cubox_i_hdmi: cubox-i-hdmigrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0
+		>;
+	};
 
-		pinctrl_cubox_i_i2c2: cubox-i-i2c2 {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
-				MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
-			>;
-		};
+	pinctrl_cubox_i_i2c2: cubox-i-i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+		>;
+	};
 
-		pinctrl_cubox_i_i2c3: cubox-i-i2c3 {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1
-				MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
-			>;
-		};
+	pinctrl_cubox_i_i2c3: cubox-i-i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1
+			MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
+		>;
+	};
 
-		pinctrl_cubox_i_ir: cubox-i-ir {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_DA9__GPIO3_IO09 0x80000000
-			>;
-		};
+	pinctrl_cubox_i_ir: cubox-i-irgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_DA9__GPIO3_IO09 0x80000000
+		>;
+	};
 
-		pinctrl_cubox_i_pwm1: cubox-i-pwm1-front-led {
-			fsl,pins = <MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0>;
-		};
+	pinctrl_cubox_i_pwm1: cubox-i-pwm1-front-ledgrp {
+		fsl,pins = <MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0>;
+	};
 
-		pinctrl_cubox_i_spdif: cubox-i-spdif {
-			fsl,pins = <MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x13091>;
-		};
+	pinctrl_cubox_i_spdif: cubox-i-spdifgrp {
+		fsl,pins = <MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x13091>;
+	};
 
-		pinctrl_cubox_i_usbh1: cubox-i-usbh1 {
-			fsl,pins = <MX6QDL_PAD_GPIO_3__USB_H1_OC 0x1b0b0>;
-		};
+	pinctrl_cubox_i_usbh1: cubox-i-usbh1grp {
+		fsl,pins = <MX6QDL_PAD_GPIO_3__USB_H1_OC 0x1b0b0>;
+	};
 
-		pinctrl_cubox_i_usbh1_vbus: cubox-i-usbh1-vbus {
-			fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x4001b0b0>;
-		};
+	pinctrl_cubox_i_usbh1_vbus: cubox-i-usbh1-vbusgrp {
+		fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x4001b0b0>;
+	};
 
-		pinctrl_cubox_i_usbotg: cubox-i-usbotg {
-			/*
-			 * The Cubox-i pulls ID low, but as it's pointless
-			 * leaving it as a pull-up, even if it is just 10uA.
-			 */
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059
-				MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0
-			>;
-		};
+	pinctrl_cubox_i_usbotg: cubox-i-usbotggrp {
+		/*
+		 * The Cubox-i pulls ID low, but as it's pointless
+		 * leaving it as a pull-up, even if it is just 10uA.
+		 */
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059
+			MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0
+		>;
+	};
 
-		pinctrl_cubox_i_usbotg_vbus: cubox-i-usbotg-vbus {
-			fsl,pins = <MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x4001b0b0>;
-		};
+	pinctrl_cubox_i_usbotg_vbus: cubox-i-usbotg-vbusgrp {
+		fsl,pins = <MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x4001b0b0>;
+	};
 
-		pinctrl_cubox_i_usdhc2_aux: cubox-i-usdhc2-aux {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_4__GPIO1_IO04    0x1f071
-				MX6QDL_PAD_KEY_ROW1__SD2_VSELECT 0x1b071
-			>;
-		};
+	pinctrl_cubox_i_usdhc2_aux: cubox-i-usdhc2-auxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04    0x1f071
+			MX6QDL_PAD_KEY_ROW1__SD2_VSELECT 0x1b071
+		>;
+	};
 
-		pinctrl_cubox_i_usdhc2: cubox-i-usdhc2 {
-			fsl,pins = <
-				MX6QDL_PAD_SD2_CMD__SD2_CMD    0x17059
-				MX6QDL_PAD_SD2_CLK__SD2_CLK    0x10059
-				MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
-				MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
-				MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
-				MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x13059
-			>;
-		};
+	pinctrl_cubox_i_usdhc2: cubox-i-usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD    0x17059
+			MX6QDL_PAD_SD2_CLK__SD2_CLK    0x10059
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x13059
+		>;
+	};
 
-		pinctrl_gpio_key: gpio-key {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_DA8__GPIO3_IO08	0x17059
-			>;
-		};
+	pinctrl_gpio_key: gpio-keygrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_DA8__GPIO3_IO08	0x17059
+		>;
 	};
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-dfi-fs700-m60.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-dfi-fs700-m60.dtsi
new file mode 100644
index 000000000000..f560a6b7779a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-dfi-fs700-m60.dtsi
@@ -0,0 +1,191 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	dummy_reg: regulator-dummy {
+		compatible = "regulator-fixed";
+		regulator-name = "dummy-supply";
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 0>;
+		enable-active-high;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+};
+
+&ecspi3 {
+	cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3>;
+	status = "okay";
+
+	flash: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "sst,sst25vf040b", "jedec,spi-nor";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	status = "okay";
+	phy-mode = "rgmii";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x80000000
+			MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x80000000 /* PMIC irq */
+			MX6QDL_PAD_EIM_D26__GPIO3_IO26 0x80000000 /* MAX11801 irq */
+			MX6QDL_PAD_NANDF_D5__GPIO2_IO05 0x000030b0 /* Backlight enable */
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_EB2__I2C2_SCL		0x4001b8b1
+			MX6QDL_PAD_EIM_D16__I2C2_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x17059
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+			MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x80000000 /* card detect */
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+		>;
+	};
+
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
+			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059
+			MX6QDL_PAD_SD4_DAT4__SD4_DATA4		0x17059
+			MX6QDL_PAD_SD4_DAT5__SD4_DATA5		0x17059
+			MX6QDL_PAD_SD4_DAT6__SD4_DATA6		0x17059
+			MX6QDL_PAD_SD4_DAT7__SD4_DATA7		0x17059
+		>;
+	};
+
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO	0x100b1
+			MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI	0x100b1
+			MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK	0x100b1
+			MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x80000000 /* SPI NOR chipselect */
+		>;
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	disable-over-current;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usdhc2 { /* module slot */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	cd-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&usdhc3 { /* baseboard slot */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+};
+
+&usdhc4 { /* eMMC */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-dhcom-drc02.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-dhcom-drc02.dtsi
index 702cd4a1b2e6..702cd4a1b2e6 100644
--- a/arch/arm/boot/dts/imx6qdl-dhcom-drc02.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-dhcom-drc02.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-dhcom-pdk2.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-dhcom-pdk2.dtsi
index fe72650295a5..d7c2b30aecfd 100644
--- a/arch/arm/boot/dts/imx6qdl-dhcom-pdk2.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-dhcom-pdk2.dtsi
@@ -56,7 +56,6 @@
 	};
 
 	gpio-keys {
-		#size-cells = <0>;
 		compatible = "gpio-keys";
 
 		button-0 {
@@ -144,6 +143,7 @@
 	panel {
 		backlight = <&display_bl>;
 		compatible = "edt,etm0700g0edh6";
+		power-supply = <&reg_panel_3v3>;
 
 		port {
 			lcd_panel_in: endpoint {
@@ -152,6 +152,25 @@
 		};
 	};
 
+	/* Filtered supply voltage */
+	reg_pdk2_24v: regulator-pdk2-24v {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <24000000>;
+		regulator-min-microvolt = <24000000>;
+		regulator-name = "24V_PDK2";
+	};
+
+	/* 560-200 U1 */
+	reg_panel_3v3: regulator-panel-3v3 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "3V3_PANEL";
+		vin-supply = <&reg_pdk2_24v>;
+	};
+
 	sound {
 		audio-codec = <&sgtl5000>;
 		audio-routing =
@@ -332,37 +351,4 @@
 			MX6QDL_PAD_GPIO_0__GPIO1_IO00		0xb1 /* Int */
 		>;
 	};
-
-	pinctrl_ipu1_lcdif: ipu1-lcdif-grp {
-		fsl,pins = <
-			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x38
-			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x38
-			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x38
-			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15		0x38
-			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x38
-			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x38
-			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x38
-			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x38
-			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x38
-			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x38
-			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x38
-			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x38
-			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x38
-			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x38
-			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x38
-			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x38
-			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x38
-			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x38
-			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x38
-			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x38
-			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x38
-			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x38
-			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18	0x38
-			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19	0x38
-			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20	0x38
-			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21	0x38
-			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22	0x38
-			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23	0x38
-		>;
-	};
 };
diff --git a/arch/arm/boot/dts/imx6qdl-dhcom-picoitx.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-dhcom-picoitx.dtsi
index 4cd4cb9543c8..4cd4cb9543c8 100644
--- a/arch/arm/boot/dts/imx6qdl-dhcom-picoitx.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-dhcom-picoitx.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-dhcom-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-dhcom-som.dtsi
index 5befbe13d1a3..af0d95396cd5 100644
--- a/arch/arm/boot/dts/imx6qdl-dhcom-som.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-dhcom-som.dtsi
@@ -256,7 +256,6 @@
 				regulator-max-microvolt = <1527272>;
 				regulator-min-microvolt = <787500>;
 				regulator-ramp-delay = <7000>;
-				regulator-suspend-mem-microvolt = <1040000>;
 			};
 
 			sw2_reg: sw2 {
@@ -275,7 +274,6 @@
 				regulator-max-microvolt = <1527272>;
 				regulator-min-microvolt = <787500>;
 				regulator-ramp-delay = <7000>;
-				regulator-suspend-mem-microvolt = <980000>;
 			};
 
 			sw4_reg: sw4 {
@@ -667,6 +665,39 @@
 		>;
 	};
 
+	pinctrl_ipu1_lcdif: ipu1-lcdif-grp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x38
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x38
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x38
+			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15		0x38
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x38
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x38
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x38
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x38
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x38
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x38
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x38
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x38
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x38
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x38
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x38
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x38
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x38
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x38
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x38
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x38
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x38
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x38
+			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18	0x38
+			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19	0x38
+			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20	0x38
+			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21	0x38
+			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22	0x38
+			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23	0x38
+		>;
+	};
+
 	pinctrl_pcie: pcie-grp {
 		fsl,pins = <
 			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20	0x1b0b1 /* Wake */
diff --git a/arch/arm/boot/dts/imx6qdl-ds.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-ds.dtsi
index f7e517555697..99ebd4dd63e8 100644
--- a/arch/arm/boot/dts/imx6qdl-ds.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-ds.dtsi
@@ -253,7 +253,7 @@
 		>;
 	};
 
-	pinctrl_ecspi1_gpio: ecspi1grpgpiogrp {
+	pinctrl_ecspi1_gpio: ecspi1gpiogrp {
 		fsl,pins = <
 			MX6QDL_PAD_KEY_ROW1__GPIO4_IO09		0x1b0b0
 			MX6QDL_PAD_ENET_RXD0__GPIO1_IO27	0x1b0b0
@@ -349,7 +349,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_gpio: usdhc1grpgpiogrp {
+	pinctrl_usdhc1_gpio: usdhc1gpiogrp {
 		fsl,pins = <
 			MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28	0x1b0b0
 		>;
@@ -366,7 +366,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_gpio: usdhc2grpgpiogrp {
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D0__GPIO2_IO00		0x1b0b0
 			MX6QDL_PAD_NANDF_D1__GPIO2_IO01		0x1b0b0
diff --git a/arch/arm/boot/dts/imx6qdl-emcon-avari.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-emcon-avari.dtsi
index c4e146f3341b..5587069b6052 100644
--- a/arch/arm/boot/dts/imx6qdl-emcon-avari.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-emcon-avari.dtsi
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: (GPL-2.0 or MIT)
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
 //
 // Copyright (C) 2018 emtrion GmbH
 //
@@ -54,7 +54,7 @@
 	clk_codec: clock-codec {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
-		clock-frequency  = <12000000>;
+		clock-frequency = <12000000>;
 	};
 
 	sound {
diff --git a/arch/arm/boot/dts/imx6qdl-emcon.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-emcon.dtsi
index 7228b894a763..9f4e746beb2d 100644
--- a/arch/arm/boot/dts/imx6qdl-emcon.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-emcon.dtsi
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: (GPL-2.0 or MIT)
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
 //
 // Copyright (C) 2018 emtrion GmbH
 //
@@ -33,7 +33,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_emcon_wake>;
 
-		wake {
+		key-wake {
 			label = "Wake";
 			linux,code = <KEY_WAKEUP>;
 			gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
@@ -46,14 +46,14 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_som_leds>;
 
-		green {
+		led-green {
 			label = "som:green";
 			gpios = <&gpio3 0 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 			default-state = "on";
 		};
 
-		red {
+		led-red {
 			label = "som:red";
 			gpios = <&gpio3 1 GPIO_ACTIVE_LOW>;
 			default-state = "keep";
@@ -66,7 +66,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_lvds_bl>;
 		enable-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>;
-		pwms = <&pwm1 0 50000>;
+		pwms = <&pwm1 0 50000 0>;
 		brightness-levels = <
 			0 4 8 16 32 64 80 96 112
 			128 144 160 176 250
@@ -78,7 +78,7 @@
 	pwm_fan: pwm-fan {
 		compatible = "pwm-fan";
 		#cooling-cells = <2>;
-		pwms = <&pwm4 0 50000>;
+		pwms = <&pwm4 0 50000 0>;
 		cooling-levels = <0 64 127 191 255>;
 		status = "disabled";
 	};
@@ -145,7 +145,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_rgb_bl>;
 		enable-gpios = <&gpio6 8 GPIO_ACTIVE_HIGH>;
-		pwms = <&pwm3 0 5000000>;
+		pwms = <&pwm3 0 5000000 0>;
 		brightness-levels = <
 			250 176 160 144 128 112
 			96 80 64 48 32 16 8 1
@@ -226,6 +226,7 @@
 		interrupt-parent = <&gpio2>;
 		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
+		#interrupt-cells = <2>;
 
 		onkey {
 			compatible = "dlg,da9063-onkey";
@@ -331,7 +332,6 @@
 };
 
 &iomuxc {
-
 	pinctrl_audmux: audmuxgrp {
 		fsl,pins = <
 			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD			0x130b0
@@ -383,79 +383,79 @@
 		>;
 	};
 
-	pinctrl_emcon_gpio1: emcongpio1 {
+	pinctrl_emcon_gpio1: emcongpio1grp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D0__GPIO2_IO00			0x0b0b1
 		>;
 	};
 
-	pinctrl_emcon_gpio2: emcongpio2 {
+	pinctrl_emcon_gpio2: emcongpio2grp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D1__GPIO2_IO01			0x0b0b1
 		>;
 	};
 
-	pinctrl_emcon_gpio3: emcongpio3 {
+	pinctrl_emcon_gpio3: emcongpio3grp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D2__GPIO2_IO02			0x0b0b1
 		>;
 	};
 
-	pinctrl_emcon_gpio4: emcongpio4 {
+	pinctrl_emcon_gpio4: emcongpio4grp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D3__GPIO2_IO03			0x0b0b1
 		>;
 	};
 
-	pinctrl_emcon_gpio5: emcongpio5 {
+	pinctrl_emcon_gpio5: emcongpio5grp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D4__GPIO2_IO04			0x0b0b1
 		>;
 	};
 
-	pinctrl_emcon_gpio6: emcongpio6 {
+	pinctrl_emcon_gpio6: emcongpio6grp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D5__GPIO2_IO05			0x0b0b1
 		>;
 	};
 
-	pinctrl_emcon_gpio7: emcongpio7 {
+	pinctrl_emcon_gpio7: emcongpio7grp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D6__GPIO2_IO06			0x0b0b1
 		>;
 	};
 
-	pinctrl_emcon_gpio8: emcongpio8 {
+	pinctrl_emcon_gpio8: emcongpio8grp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D7__GPIO2_IO07			0x0b0b1
 		>;
 	};
 
-	pinctrl_emcon_irq_a: emconirqa {
+	pinctrl_emcon_irq_a: emconirqagrp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_CLE__GPIO6_IO07		0x0b0b1
 		>;
 	};
 
-	pinctrl_emcon_irq_b: emconirqb {
+	pinctrl_emcon_irq_b: emconirqbgrp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_CS2__GPIO6_IO15		0x0b0b1
 		>;
 	};
 
-	pinctrl_emcon_irq_c: emconirqc {
+	pinctrl_emcon_irq_c: emconirqcgrp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_CS3__GPIO6_IO16		0x0b0b1
 		>;
 	};
 
-	pinctrl_emcon_irq_pwr: emconirqpwr {
+	pinctrl_emcon_irq_pwr: emconirqpwrgrp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D23__GPIO3_IO23			0x0b0b1
 		>;
 	};
 
-	pinctrl_emcon_wake: emconwake {
+	pinctrl_emcon_wake: emconwakegrp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_DA2__GPIO3_IO02			0x1b0b1
 		>;
@@ -504,13 +504,13 @@
 		>;
 	};
 
-	pinctrl_irq_touch1: irqtouch1 {
+	pinctrl_irq_touch1: irqtouch1grp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_5__GPIO1_IO05			0x0b0b1
 		>;
 	};
 
-	pinctrl_irq_touch2: irqtouch2 {
+	pinctrl_irq_touch2: irqtouch2grp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_BCLK__GPIO6_IO31			0x0b0b1
 		>;
@@ -553,7 +553,7 @@
 		>;
 	};
 
-	pinctrl_pwm_fan: pwmfan {
+	pinctrl_pwm_fan: pwmfangrp {
 		fsl,pins = <
 			MX6QDL_PAD_SD4_DAT2__PWM4_OUT			0x0b0b1
 		>;
@@ -566,7 +566,7 @@
 		>;
 	};
 
-	pinctrl_rgb_bl_en: rgbenable {
+	pinctrl_rgb_bl_en: rgbenablegrp {
 		fsl,pins = <
 			MX6QDL_PAD_SD4_CMD__GPIO7_IO09			0x0b0b1
 		>;
@@ -618,13 +618,13 @@
 		>;
 	};
 
-	pinctrl_spdif_in: spdifin {
+	pinctrl_spdif_in: spdifingrp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_16__SPDIF_IN			0x1b0b0
 		>;
 	};
 
-	pinctrl_spdif_out: spdifout {
+	pinctrl_spdif_out: spdifoutgrp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_19__SPDIF_OUT			0x13091
 		>;
@@ -737,17 +737,14 @@
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	status = "okay";
 };
 
 &pwm3 {
-	#pwm-cells = <2>;
 	status = "okay";
 };
 
 &pwm4 {
-	#pwm-cells = <2>;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw51xx.dtsi
index 069c27fab432..beff5a0f58ab 100644
--- a/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw51xx.dtsi
@@ -24,13 +24,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		user-pb {
+		key-user-pb {
 			label = "user_pb";
 			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_0>;
 		};
 
-		user-pb1x {
+		key-user-pb1x {
 			label = "user_pb1x";
 			linux,code = <BTN_1>;
 			interrupt-parent = <&gsc>;
@@ -44,21 +44,21 @@
 			interrupts = <1>;
 		};
 
-		eeprom-wp {
+		key-eeprom-wp {
 			label = "eeprom_wp";
 			linux,code = <BTN_3>;
 			interrupt-parent = <&gsc>;
 			interrupts = <2>;
 		};
 
-		tamper {
+		key-tamper {
 			label = "tamper";
 			linux,code = <BTN_4>;
 			interrupt-parent = <&gsc>;
 			interrupts = <5>;
 		};
 
-		switch-hold {
+		key-switch-hold {
 			label = "switch_hold";
 			linux,code = <BTN_5>;
 			interrupt-parent = <&gsc>;
@@ -71,14 +71,14 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 
-		led1: user2 {
+		led1: led-user2 {
 			label = "user2";
 			gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
 			default-state = "off";
@@ -156,6 +156,7 @@
 		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
+		#address-cells = <1>;
 		#size-cells = <0>;
 
 		adc {
@@ -270,7 +271,7 @@
 		pagesize = <16>;
 	};
 
-	rtc: ds1672@68 {
+	rtc: rtc@68 {
 		compatible = "dallas,ds1672";
 		reg = <0x68>;
 	};
diff --git a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw52xx.dtsi
index b1df2beb2832..9d3ba4083216 100644
--- a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw52xx.dtsi
@@ -25,7 +25,7 @@
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm4 0 5000000>;
+		pwms = <&pwm4 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 	};
@@ -33,13 +33,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		user-pb {
+		key-user-pb {
 			label = "user_pb";
 			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_0>;
 		};
 
-		user-pb1x {
+		key-user-pb1x {
 			label = "user_pb1x";
 			linux,code = <BTN_1>;
 			interrupt-parent = <&gsc>;
@@ -53,21 +53,21 @@
 			interrupts = <1>;
 		};
 
-		eeprom-wp {
+		key-eeprom-wp {
 			label = "eeprom_wp";
 			linux,code = <BTN_3>;
 			interrupt-parent = <&gsc>;
 			interrupts = <2>;
 		};
 
-		tamper {
+		key-tamper {
 			label = "tamper";
 			linux,code = <BTN_4>;
 			interrupt-parent = <&gsc>;
 			interrupts = <5>;
 		};
 
-		switch-hold {
+		key-switch-hold {
 			label = "switch_hold";
 			linux,code = <BTN_5>;
 			interrupt-parent = <&gsc>;
@@ -80,20 +80,20 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 
-		led1: user2 {
+		led1: led-user2 {
 			label = "user2";
 			gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
 			default-state = "off";
 		};
 
-		led2: user3 {
+		led2: led-user3 {
 			label = "user3";
 			gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* MX6_LOCLED# */
 			default-state = "off";
@@ -137,6 +137,16 @@
 		regulator-always-on;
 	};
 
+	reg_can1_stby: regulator-can1-stby {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_can1>;
+		regulator-name = "can1_stby";
+		gpio = <&gpio1 9 GPIO_ACTIVE_LOW>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
 	reg_usb_otg_vbus: regulator-usb-otg-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "usb_otg_vbus";
@@ -170,6 +180,7 @@
 &can1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_can1_stby>;
 	status = "okay";
 };
 
@@ -219,6 +230,7 @@
 		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
+		#address-cells = <1>;
 		#size-cells = <0>;
 
 		adc {
@@ -339,7 +351,7 @@
 		pagesize = <16>;
 	};
 
-	rtc: ds1672@68 {
+	rtc: rtc@68 {
 		compatible = "dallas,ds1672";
 		reg = <0x68>;
 	};
@@ -444,6 +456,7 @@
 	codec: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
 		VDDA-supply = <&reg_1p8v>;
 		VDDIO-supply = <&reg_3p3v>;
@@ -473,7 +486,7 @@
 
 		display-timings {
 			native-mode = <&timing0>;
-			timing0: hsd100pxn1 {
+			timing0: timing-hsd100pxn1 {
 				clock-frequency = <65000000>;
 				hactive = <1024>;
 				vactive = <768>;
@@ -508,7 +521,6 @@
 };
 
 &pwm4 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "okay";
@@ -612,7 +624,6 @@
 		fsl,pins = <
 			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX	0x1b0b1
 			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b1
-			MX6QDL_PAD_GPIO_9__GPIO1_IO09		0x4001b0b0 /* CAN_STBY */
 		>;
 	};
 
@@ -702,6 +713,12 @@
 		>;
 	};
 
+	pinctrl_reg_can1: regcan1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__GPIO1_IO09		0x4001b0b0 /* CAN_STBY */
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
@@ -745,7 +762,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+	pinctrl_usdhc3_100mhz: usdhc3-100mhz-grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170b9
 			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x170b9
@@ -758,7 +775,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+	pinctrl_usdhc3_200mhz: usdhc3-200mhz-grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170f9
 			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100f9
diff --git a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw53xx.dtsi
index a0710d562766..7e84e0a52ef3 100644
--- a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw53xx.dtsi
@@ -25,7 +25,7 @@
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm4 0 5000000>;
+		pwms = <&pwm4 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 	};
@@ -33,13 +33,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		user-pb {
+		key-user-pb {
 			label = "user_pb";
 			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_0>;
 		};
 
-		user-pb1x {
+		key-user-pb1x {
 			label = "user_pb1x";
 			linux,code = <BTN_1>;
 			interrupt-parent = <&gsc>;
@@ -53,21 +53,21 @@
 			interrupts = <1>;
 		};
 
-		eeprom-wp {
+		key-eeprom-wp {
 			label = "eeprom_wp";
 			linux,code = <BTN_3>;
 			interrupt-parent = <&gsc>;
 			interrupts = <2>;
 		};
 
-		tamper {
+		key-tamper {
 			label = "tamper";
 			linux,code = <BTN_4>;
 			interrupt-parent = <&gsc>;
 			interrupts = <5>;
 		};
 
-		switch-hold {
+		key-switch-hold {
 			label = "switch_hold";
 			linux,code = <BTN_5>;
 			interrupt-parent = <&gsc>;
@@ -80,20 +80,20 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 
-		led1: user2 {
+		led1: led-user2 {
 			label = "user2";
 			gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
 			default-state = "off";
 		};
 
-		led2: user3 {
+		led2: led-user3 {
 			label = "user3";
 			gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* MX6_LOCLED# */
 			default-state = "off";
@@ -129,6 +129,16 @@
 		regulator-always-on;
 	};
 
+	reg_can1_stby: regulator-can1-stby {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_can1>;
+		regulator-name = "can1_stby";
+		gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
 	reg_usb_h1_vbus: regulator-usb-h1-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "usb_h1_vbus";
@@ -170,6 +180,7 @@
 &can1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_can1_stby>;
 	status = "okay";
 };
 
@@ -212,6 +223,7 @@
 		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
+		#address-cells = <1>;
 		#size-cells = <0>;
 
 		adc {
@@ -338,7 +350,7 @@
 		pagesize = <16>;
 	};
 
-	rtc: ds1672@68 {
+	rtc: rtc@68 {
 		compatible = "dallas,ds1672";
 		reg = <0x68>;
 	};
@@ -441,6 +453,7 @@
 	codec: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
 		VDDA-supply = <&reg_1p8v>;
 		VDDIO-supply = <&reg_3p3v>;
@@ -470,7 +483,7 @@
 
 		display-timings {
 			native-mode = <&timing0>;
-			timing0: hsd100pxn1 {
+			timing0: timing-hsd100pxn1 {
 				clock-frequency = <65000000>;
 				hactive = <1024>;
 				vactive = <768>;
@@ -505,7 +518,6 @@
 };
 
 &pwm4 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "okay";
@@ -600,7 +612,6 @@
 		fsl,pins = <
 			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX	0x1b0b1
 			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b1
-			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x4001b0b0 /* CAN_STBY */
 		>;
 	};
 
@@ -691,6 +702,12 @@
 		>;
 	};
 
+	pinctrl_reg_can1: regcan1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x4001b0b0 /* CAN_STBY */
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
@@ -734,7 +751,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+	pinctrl_usdhc3_100mhz: usdhc3-100mhz-grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170b9
 			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100b9
@@ -747,7 +764,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+	pinctrl_usdhc3_200mhz: usdhc3-200mhz-grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170f9
 			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100f9
diff --git a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw54xx.dtsi
index cda48bf2f168..81394d47dd68 100644
--- a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw54xx.dtsi
@@ -26,7 +26,7 @@
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm4 0 5000000>;
+		pwms = <&pwm4 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 	};
@@ -34,13 +34,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		user-pb {
+		key-user-pb {
 			label = "user_pb";
 			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_0>;
 		};
 
-		user-pb1x {
+		key-user-pb1x {
 			label = "user_pb1x";
 			linux,code = <BTN_1>;
 			interrupt-parent = <&gsc>;
@@ -54,21 +54,21 @@
 			interrupts = <1>;
 		};
 
-		eeprom-wp {
+		key-eeprom-wp {
 			label = "eeprom_wp";
 			linux,code = <BTN_3>;
 			interrupt-parent = <&gsc>;
 			interrupts = <2>;
 		};
 
-		tamper {
+		key-tamper {
 			label = "tamper";
 			linux,code = <BTN_4>;
 			interrupt-parent = <&gsc>;
 			interrupts = <5>;
 		};
 
-		switch-hold {
+		key-switch-hold {
 			label = "switch_hold";
 			linux,code = <BTN_5>;
 			interrupt-parent = <&gsc>;
@@ -81,20 +81,20 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 
-		led1: user2 {
+		led1: led-user2 {
 			label = "user2";
 			gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
 			default-state = "off";
 		};
 
-		led2: user3 {
+		led2: led-user3 {
 			label = "user3";
 			gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* MX6_LOCLED# */
 			default-state = "off";
@@ -114,47 +114,47 @@
 		status = "okay";
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
+	reg_1p0v: regulator-1p0v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P0V";
+		regulator-min-microvolt = <1000000>;
+		regulator-max-microvolt = <1000000>;
+		regulator-always-on;
+	};
 
-		reg_1p0v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "1P0V";
-			regulator-min-microvolt = <1000000>;
-			regulator-max-microvolt = <1000000>;
-			regulator-always-on;
-		};
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 
-		reg_3p3v: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	reg_can1_stby: regulator-can1-stby {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_can1>;
+		regulator-name = "can1_stby";
+		gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
 
-		reg_usb_h1_vbus: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "usb_h1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-		};
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
 
-		reg_usb_otg_vbus: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "usb_otg_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
 	};
 
 	sound-analog {
@@ -177,7 +177,7 @@
 	pinctrl-0 = <&pinctrl_audmux>; /* AUD4<->sgtl5000 */
 	status = "okay";
 
-	ssi2 {
+	mux-ssi2 {
 		fsl,audmux-port = <1>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_TFSDIR |
@@ -189,7 +189,7 @@
 		>;
 	};
 
-	aud5 {
+	mux-aud5 {
 		fsl,audmux-port = <4>;
 		fsl,port-config = <
 			IMX_AUDMUX_V2_PTCR_SYN
@@ -200,6 +200,7 @@
 &can1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_can1_stby>;
 	status = "okay";
 };
 
@@ -338,8 +339,6 @@
 
 		fan-controller@2c {
 			compatible = "gw,gsc-fan";
-			#address-cells = <1>;
-			#size-cells = <0>;
 			reg = <0x2c>;
 		};
 	};
@@ -377,7 +376,7 @@
 		pagesize = <16>;
 	};
 
-	rtc: ds1672@68 {
+	rtc: rtc@68 {
 		compatible = "dallas,ds1672";
 		reg = <0x68>;
 	};
@@ -389,7 +388,7 @@
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
 		reg = <0x08>;
 
@@ -500,6 +499,7 @@
 	sgtl5000: audio-codec@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
 		VDDA-supply = <&sw4_reg>;
 		VDDIO-supply = <&reg_3p3v>;
@@ -529,7 +529,7 @@
 
 		display-timings {
 			native-mode = <&timing0>;
-			timing0: hsd100pxn1 {
+			timing0: timing-hsd100pxn1 {
 				clock-frequency = <65000000>;
 				hactive = <1024>;
 				vactive = <768>;
@@ -570,7 +570,6 @@
 };
 
 &pwm4 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default", "state_dio";
 	pinctrl-0 = <&pinctrl_pwm4_backlight>;
 	pinctrl-1 = <&pinctrl_pwm4_dio>;
@@ -687,7 +686,6 @@
 		fsl,pins = <
 			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX	0x1b0b1
 			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b1
-			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x4001b0b0 /* CAN_STBY */
 		>;
 	};
 
@@ -772,20 +770,26 @@
 		>;
 	};
 
-	pinctrl_pwm4_backlight: pwm4grpbacklight {
+	pinctrl_pwm4_backlight: pwm4backlightgrp {
 		fsl,pins = <
 			/* LVDS_PWM J6.5 */
 			MX6QDL_PAD_SD1_CMD__PWM4_OUT		0x1b0b1
 		>;
 	};
 
-	pinctrl_pwm4_dio: pwm4grpdio {
+	pinctrl_pwm4_dio: pwm4diogrp {
 		fsl,pins = <
 			/* DIO3 J16.4 */
 			MX6QDL_PAD_SD4_DAT2__PWM4_OUT		0x1b0b1
 		>;
 	};
 
+	pinctrl_reg_can1: regcan1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x4001b0b0 /* CAN_STBY */
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
@@ -829,7 +833,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+	pinctrl_usdhc3_100mhz: usdhc3-100mhz-grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170b9
 			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100b9
@@ -842,7 +846,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+	pinctrl_usdhc3_200mhz: usdhc3-200mhz-grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170f9
 			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100f9
diff --git a/arch/arm/boot/dts/imx6qdl-gw551x.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw551x.dtsi
index 435dec6338fe..6136a95b9259 100644
--- a/arch/arm/boot/dts/imx6qdl-gw551x.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw551x.dtsi
@@ -1,48 +1,6 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
 /*
  * Copyright 2014 Gateworks Corporation
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of
- *     the License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- *     You should have received a copy of the GNU General Public
- *     License along with this file; if not, write to the Free
- *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
- *     MA 02110-1301 USA
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 #include <dt-bindings/gpio/gpio.h>
@@ -68,13 +26,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		user-pb {
+		key-user-pb {
 			label = "user_pb";
 			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_0>;
 		};
 
-		user-pb1x {
+		key-user-pb1x {
 			label = "user_pb1x";
 			linux,code = <BTN_1>;
 			interrupt-parent = <&gsc>;
@@ -88,21 +46,21 @@
 			interrupts = <1>;
 		};
 
-		eeprom-wp {
+		key-eeprom-wp {
 			label = "eeprom_wp";
 			linux,code = <BTN_3>;
 			interrupt-parent = <&gsc>;
 			interrupts = <2>;
 		};
 
-		tamper {
+		key-tamper {
 			label = "tamper";
 			linux,code = <BTN_4>;
 			interrupt-parent = <&gsc>;
 			interrupts = <5>;
 		};
 
-		switch-hold {
+		key-switch-hold {
 			label = "switch_hold";
 			linux,code = <BTN_5>;
 			interrupt-parent = <&gsc>;
@@ -115,7 +73,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio4 7 GPIO_ACTIVE_LOW>;
 			default-state = "on";
@@ -171,7 +129,7 @@
 	pinctrl-0 = <&pinctrl_audmux>; /* AUD5<->tda1997x */
 	status = "okay";
 
-	ssi1 {
+	mux-ssi1 {
 		fsl,audmux-port = <0>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_TFSDIR |
@@ -183,7 +141,7 @@
 		>;
 	};
 
-	aud5 {
+	mux-aud5 {
 		fsl,audmux-port = <4>;
 		fsl,port-config = <
 			IMX_AUDMUX_V2_PTCR_SYN
@@ -221,6 +179,7 @@
 		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
+		#address-cells = <1>;
 		#size-cells = <0>;
 
 		adc {
@@ -329,7 +288,7 @@
 		pagesize = <16>;
 	};
 
-	rtc: ds1672@68 {
+	rtc: rtc@68 {
 		compatible = "dallas,ds1672";
 		reg = <0x68>;
 	};
diff --git a/arch/arm/boot/dts/imx6qdl-gw552x.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw552x.dtsi
index 2e61102ae694..9c822ca23130 100644
--- a/arch/arm/boot/dts/imx6qdl-gw552x.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw552x.dtsi
@@ -25,13 +25,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		user-pb {
+		key-user-pb {
 			label = "user_pb";
 			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_0>;
 		};
 
-		user-pb1x {
+		key-user-pb1x {
 			label = "user_pb1x";
 			linux,code = <BTN_1>;
 			interrupt-parent = <&gsc>;
@@ -45,21 +45,21 @@
 			interrupts = <1>;
 		};
 
-		eeprom-wp {
+		key-eeprom-wp {
 			label = "eeprom_wp";
 			linux,code = <BTN_3>;
 			interrupt-parent = <&gsc>;
 			interrupts = <2>;
 		};
 
-		tamper {
+		key-tamper {
 			label = "tamper";
 			linux,code = <BTN_4>;
 			interrupt-parent = <&gsc>;
 			interrupts = <5>;
 		};
 
-		switch-hold {
+		key-switch-hold {
 			label = "switch_hold";
 			linux,code = <BTN_5>;
 			interrupt-parent = <&gsc>;
@@ -72,20 +72,20 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 
-		led1: user2 {
+		led1: led-user2 {
 			label = "user2";
 			gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
 			default-state = "off";
 		};
 
-		led2: user3 {
+		led2: led-user3 {
 			label = "user3";
 			gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* MX6_LOCLED# */
 			default-state = "off";
@@ -146,6 +146,7 @@
 		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
+		#address-cells = <1>;
 		#size-cells = <0>;
 
 		adc {
@@ -260,7 +261,7 @@
 		pagesize = <16>;
 	};
 
-	rtc: ds1672@68 {
+	rtc: rtc@68 {
 		compatible = "dallas,ds1672";
 		reg = <0x68>;
 	};
diff --git a/arch/arm/boot/dts/imx6qdl-gw553x.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw553x.dtsi
index 4662408b225a..552114a69f5b 100644
--- a/arch/arm/boot/dts/imx6qdl-gw553x.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw553x.dtsi
@@ -1,48 +1,6 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
 /*
  * Copyright 2016 Gateworks Corporation
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of
- *     the License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- *     You should have received a copy of the GNU General Public
- *     License along with this file; if not, write to the Free
- *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
- *     MA 02110-1301 USA
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 #include <dt-bindings/gpio/gpio.h>
@@ -66,13 +24,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		user-pb {
+		key-user-pb {
 			label = "user_pb";
 			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_0>;
 		};
 
-		user-pb1x {
+		key-user-pb1x {
 			label = "user_pb1x";
 			linux,code = <BTN_1>;
 			interrupt-parent = <&gsc>;
@@ -86,21 +44,21 @@
 			interrupts = <1>;
 		};
 
-		eeprom-wp {
+		key-eeprom-wp {
 			label = "eeprom_wp";
 			linux,code = <BTN_3>;
 			interrupt-parent = <&gsc>;
 			interrupts = <2>;
 		};
 
-		tamper {
+		key-tamper {
 			label = "tamper";
 			linux,code = <BTN_4>;
 			interrupt-parent = <&gsc>;
 			interrupts = <5>;
 		};
 
-		switch-hold {
+		key-switch-hold {
 			label = "switch_hold";
 			linux,code = <BTN_5>;
 			interrupt-parent = <&gsc>;
@@ -113,14 +71,14 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio4 10 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 
-		led1: user2 {
+		led1: led-user2 {
 			label = "user2";
 			gpios = <&gpio4 11 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
 			default-state = "off";
@@ -184,6 +142,7 @@
 		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
+		#address-cells = <1>;
 		#size-cells = <0>;
 
 		adc {
@@ -298,7 +257,7 @@
 		pagesize = <16>;
 	};
 
-	rtc: ds1672@68 {
+	rtc: rtc@68 {
 		compatible = "dallas,ds1672";
 		reg = <0x68>;
 	};
@@ -704,7 +663,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+	pinctrl_usdhc3_100mhz: usdhc3-100mhz-grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170b9
 			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100b9
@@ -717,7 +676,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+	pinctrl_usdhc3_200mhz: usdhc3-200mhz-grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170f9
 			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100f9
diff --git a/arch/arm/boot/dts/imx6qdl-gw560x.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw560x.dtsi
index 4bc4371e6bae..ea92b2b5c50d 100644
--- a/arch/arm/boot/dts/imx6qdl-gw560x.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw560x.dtsi
@@ -1,48 +1,6 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
 /*
  * Copyright 2017 Gateworks Corporation
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of
- *     the License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- *     You should have received a copy of the GNU General Public
- *     License along with this file; if not, write to the Free
- *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
- *     MA 02110-1301 USA
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 #include <dt-bindings/gpio/gpio.h>
@@ -66,7 +24,7 @@
 
 	backlight-display {
 		compatible = "pwm-backlight";
-		pwms = <&pwm4 0 5000000>;
+		pwms = <&pwm4 0 5000000 0>;
 		brightness-levels = <
 			0  1  2  3  4  5  6  7  8  9
 			10 11 12 13 14 15 16 17 18 19
@@ -92,13 +50,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		user-pb {
+		key-user-pb {
 			label = "user_pb";
 			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_0>;
 		};
 
-		user-pb1x {
+		key-user-pb1x {
 			label = "user_pb1x";
 			linux,code = <BTN_1>;
 			interrupt-parent = <&gsc>;
@@ -112,21 +70,21 @@
 			interrupts = <1>;
 		};
 
-		eeprom-wp {
+		key-eeprom-wp {
 			label = "eeprom_wp";
 			linux,code = <BTN_3>;
 			interrupt-parent = <&gsc>;
 			interrupts = <2>;
 		};
 
-		tamper {
+		key-tamper {
 			label = "tamper";
 			linux,code = <BTN_4>;
 			interrupt-parent = <&gsc>;
 			interrupts = <5>;
 		};
 
-		switch-hold {
+		key-switch-hold {
 			label = "switch_hold";
 			linux,code = <BTN_5>;
 			interrupt-parent = <&gsc>;
@@ -139,20 +97,20 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 
-		led1: user2 {
+		led1: led-user2 {
 			label = "user2";
 			gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
 			default-state = "off";
 		};
 
-		led2: user3 {
+		led2: led-user3 {
 			label = "user3";
 			gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* MX6_LOCLED# */
 			default-state = "off";
@@ -296,6 +254,7 @@
 		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
+		#address-cells = <1>;
 		#size-cells = <0>;
 
 		adc {
@@ -584,7 +543,7 @@
 
 		display-timings {
 			native-mode = <&timing0>;
-			timing0: hsd100pxn1 {
+			timing0: timing-hsd100pxn1 {
 				clock-frequency = <65000000>;
 				hactive = <1024>;
 				vactive = <768>;
@@ -619,7 +578,6 @@
 };
 
 &pwm4 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "okay";
@@ -632,7 +590,6 @@
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1>;
-	uart-has-rtscts;
 	rts-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
@@ -898,7 +855,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+	pinctrl_usdhc3_100mhz: usdhc3-100mhz-grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170b9
 			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100b9
@@ -911,7 +868,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+	pinctrl_usdhc3_200mhz: usdhc3-200mhz-grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170f9
 			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100f9
diff --git a/arch/arm/boot/dts/imx6qdl-gw5903.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5903.dtsi
index 1fdb7ba630f1..b518bcb6b7a9 100644
--- a/arch/arm/boot/dts/imx6qdl-gw5903.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5903.dtsi
@@ -1,48 +1,6 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
 /*
  * Copyright 2017 Gateworks Corporation
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of
- *     the License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- *     You should have received a copy of the GNU General Public
- *     License along with this file; if not, write to the Free
- *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
- *     MA 02110-1301 USA
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 #include <dt-bindings/gpio/gpio.h>
@@ -56,7 +14,7 @@
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <
 			0  1  2  3  4  5  6  7  8  9
 			10 11 12 13 14 15 16 17 18 19
@@ -76,13 +34,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		user-pb {
+		key-user-pb {
 			label = "user_pb";
 			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_0>;
 		};
 
-		user-pb1x {
+		key-user-pb1x {
 			label = "user_pb1x";
 			linux,code = <BTN_1>;
 			interrupt-parent = <&gsc>;
@@ -96,21 +54,21 @@
 			interrupts = <1>;
 		};
 
-		eeprom-wp {
+		key-eeprom-wp {
 			label = "eeprom_wp";
 			linux,code = <BTN_3>;
 			interrupt-parent = <&gsc>;
 			interrupts = <2>;
 		};
 
-		tamper {
+		key-tamper {
 			label = "tamper";
 			linux,code = <BTN_4>;
 			interrupt-parent = <&gsc>;
 			interrupts = <5>;
 		};
 
-		switch-hold {
+		key-switch-hold {
 			label = "switch_hold";
 			linux,code = <BTN_5>;
 			interrupt-parent = <&gsc>;
@@ -123,7 +81,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio6 14 GPIO_ACTIVE_LOW>; /* MX6_LOCLED# */
 			default-state = "off";
@@ -237,6 +195,7 @@
 		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
+		#address-cells = <1>;
 		#size-cells = <0>;
 
 		adc {
@@ -486,7 +445,7 @@
 
 		display-timings {
 			native-mode = <&timing0>;
-			timing0: g101evn010 {
+			timing0: timing-g101evn010 {
 				clock-frequency = <68930000>;
 				hactive = <1280>;
 				vactive = <800>;
@@ -502,7 +461,6 @@
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
@@ -681,7 +639,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+	pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D3__GPIO2_IO03		0x4001b0b0 /* EMMY_EN */
 			MX6QDL_PAD_NANDF_D4__GPIO2_IO04		0x4001b0b0 /* EMMY_CFG1# */
@@ -711,7 +669,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+	pinctrl_usdhc2_100mhz: usdhc2-100mhz-grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x170b9
 			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x100b9
@@ -724,7 +682,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+	pinctrl_usdhc2_200mhz: usdhc2-200mhz-grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x170f9
 			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x100f9
@@ -753,7 +711,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+	pinctrl_usdhc3_100mhz: usdhc3-100mhz-grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170b9
 			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100b9
@@ -769,7 +727,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+	pinctrl_usdhc3_200mhz: usdhc3-200mhz-grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170f9
 			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100f9
diff --git a/arch/arm/boot/dts/imx6qdl-gw5904.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5904.dtsi
index 612b6e068e28..3df4d345da98 100644
--- a/arch/arm/boot/dts/imx6qdl-gw5904.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5904.dtsi
@@ -1,48 +1,6 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
 /*
  * Copyright 2017 Gateworks Corporation
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of
- *     the License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- *     You should have received a copy of the GNU General Public
- *     License along with this file; if not, write to the Free
- *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
- *     MA 02110-1301 USA
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 #include <dt-bindings/gpio/gpio.h>
@@ -52,6 +10,11 @@
 / {
 	/* these are used by bootloader for disabling nodes */
 	aliases {
+		ethernet0 = &fec;
+		ethernet1 = &lan1;
+		ethernet2 = &lan2;
+		ethernet3 = &lan3;
+		ethernet4 = &lan4;
 		led0 = &led0;
 		led1 = &led1;
 		led2 = &led2;
@@ -65,7 +28,7 @@
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm4 0 5000000>;
+		pwms = <&pwm4 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 	};
@@ -73,13 +36,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		user-pb {
+		key-user-pb {
 			label = "user_pb";
 			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_0>;
 		};
 
-		user-pb1x {
+		key-user-pb1x {
 			label = "user_pb1x";
 			linux,code = <BTN_1>;
 			interrupt-parent = <&gsc>;
@@ -93,21 +56,21 @@
 			interrupts = <1>;
 		};
 
-		eeprom-wp {
+		key-eeprom-wp {
 			label = "eeprom_wp";
 			linux,code = <BTN_3>;
 			interrupt-parent = <&gsc>;
 			interrupts = <2>;
 		};
 
-		tamper {
+		key-tamper {
 			label = "tamper";
 			linux,code = <BTN_4>;
 			interrupt-parent = <&gsc>;
 			interrupts = <5>;
 		};
 
-		switch-hold {
+		key-switch-hold {
 			label = "switch_hold";
 			linux,code = <BTN_5>;
 			interrupt-parent = <&gsc>;
@@ -120,20 +83,20 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 
-		led1: user2 {
+		led1: led-user2 {
 			label = "user2";
 			gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
 			default-state = "off";
 		};
 
-		led2: user3 {
+		led2: led-user3 {
 			label = "user3";
 			gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* MX6_LOCLED# */
 			default-state = "off";
@@ -212,34 +175,72 @@
 			compatible = "marvell,mv88e6085";
 			reg = <0>;
 
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				sw_phy0: ethernet-phy@0 {
+					reg = <0x0>;
+				};
+
+				sw_phy1: ethernet-phy@1 {
+					reg = <0x1>;
+				};
+
+				sw_phy2: ethernet-phy@2 {
+					reg = <0x2>;
+				};
+
+				sw_phy3: ethernet-phy@3 {
+					reg = <0x3>;
+				};
+			};
+
 			ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				port@0 {
+				lan4: port@0 {
 					reg = <0>;
 					label = "lan4";
+					phy-handle = <&sw_phy0>;
+					phy-mode = "internal";
+					local-mac-address = [00 00 00 00 00 00];
 				};
 
-				port@1 {
+				lan3: port@1 {
 					reg = <1>;
 					label = "lan3";
+					phy-handle = <&sw_phy1>;
+					phy-mode = "internal";
+					local-mac-address = [00 00 00 00 00 00];
 				};
 
-				port@2 {
+				lan2: port@2 {
 					reg = <2>;
 					label = "lan2";
+					phy-handle = <&sw_phy2>;
+					phy-mode = "internal";
+					local-mac-address = [00 00 00 00 00 00];
 				};
 
-				port@3 {
+				lan1: port@3 {
 					reg = <3>;
 					label = "lan1";
+					phy-handle = <&sw_phy3>;
+					phy-mode = "internal";
+					local-mac-address = [00 00 00 00 00 00];
 				};
 
 				port@5 {
 					reg = <5>;
-					label = "cpu";
 					ethernet = <&fec>;
+					phy-mode = "rgmii-id";
+
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
 				};
 			};
 		};
@@ -259,6 +260,7 @@
 		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
+		#address-cells = <1>;
 		#size-cells = <0>;
 
 		adc {
@@ -508,7 +510,7 @@
 
 		display-timings {
 			native-mode = <&timing0>;
-			timing0: hsd100pxn1 {
+			timing0: timing-hsd100pxn1 {
 				clock-frequency = <65000000>;
 				hactive = <1024>;
 				vactive = <768>;
@@ -543,7 +545,6 @@
 };
 
 &pwm4 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "okay";
@@ -775,7 +776,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+	pinctrl_usdhc3_100mhz: usdhc3-100mhz-grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170b9
 			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100b9
@@ -791,7 +792,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+	pinctrl_usdhc3_200mhz: usdhc3-200mhz-grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170f9
 			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100f9
diff --git a/arch/arm/boot/dts/imx6qdl-gw5907.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5907.dtsi
index fcd3bdfd6182..87fdc9e2a727 100644
--- a/arch/arm/boot/dts/imx6qdl-gw5907.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5907.dtsi
@@ -24,13 +24,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		user-pb {
+		key-user-pb {
 			label = "user_pb";
 			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_0>;
 		};
 
-		user-pb1x {
+		key-user-pb1x {
 			label = "user_pb1x";
 			linux,code = <BTN_1>;
 			interrupt-parent = <&gsc>;
@@ -44,21 +44,21 @@
 			interrupts = <1>;
 		};
 
-		eeprom-wp {
+		key-eeprom-wp {
 			label = "eeprom_wp";
 			linux,code = <BTN_3>;
 			interrupt-parent = <&gsc>;
 			interrupts = <2>;
 		};
 
-		tamper {
+		key-tamper {
 			label = "tamper";
 			linux,code = <BTN_4>;
 			interrupt-parent = <&gsc>;
 			interrupts = <5>;
 		};
 
-		switch-hold {
+		key-switch-hold {
 			label = "switch_hold";
 			linux,code = <BTN_5>;
 			interrupt-parent = <&gsc>;
@@ -71,14 +71,14 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 
-		led1: user2 {
+		led1: led-user2 {
 			label = "user2";
 			gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
 			default-state = "off";
@@ -156,6 +156,7 @@
 		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
+		#address-cells = <1>;
 		#size-cells = <0>;
 
 		adc {
@@ -270,7 +271,7 @@
 		pagesize = <16>;
 	};
 
-	ds1672@68 {
+	rtc@68 {
 		compatible = "dallas,ds1672";
 		reg = <0x68>;
 	};
diff --git a/arch/arm/boot/dts/imx6qdl-gw5910.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5910.dtsi
index 68e5ab2e27e2..099ed2f94d61 100644
--- a/arch/arm/boot/dts/imx6qdl-gw5910.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5910.dtsi
@@ -27,13 +27,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		user-pb {
+		key-user-pb {
 			label = "user_pb";
-			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
+			gpios = <&gsc_gpio 2 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_0>;
 		};
 
-		user-pb1x {
+		key-user-pb1x {
 			label = "user_pb1x";
 			linux,code = <BTN_1>;
 			interrupt-parent = <&gsc>;
@@ -47,21 +47,21 @@
 			interrupts = <1>;
 		};
 
-		eeprom-wp {
+		key-eeprom-wp {
 			label = "eeprom_wp";
 			linux,code = <BTN_3>;
 			interrupt-parent = <&gsc>;
 			interrupts = <2>;
 		};
 
-		tamper {
+		key-tamper {
 			label = "tamper";
 			linux,code = <BTN_4>;
 			interrupt-parent = <&gsc>;
 			interrupts = <5>;
 		};
 
-		switch-hold {
+		key-switch-hold {
 			label = "switch_hold";
 			linux,code = <BTN_5>;
 			interrupt-parent = <&gsc>;
@@ -74,20 +74,20 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 
-		led1: user2 {
+		led1: led-user2 {
 			label = "user2";
 			gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
 			default-state = "off";
 		};
 
-		led2: user3 {
+		led2: led-user3 {
 			label = "user3";
 			gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* MX6_LOCLED# */
 			default-state = "off";
@@ -165,6 +165,7 @@
 		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
+		#address-cells = <1>;
 		#size-cells = <0>;
 
 		adc {
@@ -326,7 +327,6 @@
 		st,drdy-int-pin = <1>;
 		interrupt-parent = <&gpio7>;
 		interrupts = <13 0>;
-		interrupt-names = "INT1";
 	};
 };
 
@@ -630,7 +630,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+	pinctrl_usdhc3_100mhz: usdhc3-100mhz-grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170b9
 			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x170b9
@@ -643,7 +643,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+	pinctrl_usdhc3_200mhz: usdhc3-200mhz-grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170f9
 			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100f9
diff --git a/arch/arm/boot/dts/imx6qdl-gw5912.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5912.dtsi
index 0415bcb41640..cbca5e58e812 100644
--- a/arch/arm/boot/dts/imx6qdl-gw5912.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5912.dtsi
@@ -25,13 +25,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		user-pb {
+		key-user-pb {
 			label = "user_pb";
 			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_0>;
 		};
 
-		user-pb1x {
+		key-user-pb1x {
 			label = "user_pb1x";
 			linux,code = <BTN_1>;
 			interrupt-parent = <&gsc>;
@@ -45,21 +45,21 @@
 			interrupts = <1>;
 		};
 
-		eeprom-wp {
+		key-eeprom-wp {
 			label = "eeprom_wp";
 			linux,code = <BTN_3>;
 			interrupt-parent = <&gsc>;
 			interrupts = <2>;
 		};
 
-		tamper {
+		key-tamper {
 			label = "tamper";
 			linux,code = <BTN_4>;
 			interrupt-parent = <&gsc>;
 			interrupts = <5>;
 		};
 
-		switch-hold {
+		key-switch-hold {
 			label = "switch_hold";
 			linux,code = <BTN_5>;
 			interrupt-parent = <&gsc>;
@@ -72,20 +72,20 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 
-		led1: user2 {
+		led1: led-user2 {
 			label = "user2";
 			gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
 			default-state = "off";
 		};
 
-		led2: user3 {
+		led2: led-user3 {
 			label = "user3";
 			gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; /* MX6_LOCLED# */
 			default-state = "off";
@@ -243,8 +243,6 @@
 
 		fan-controller@a {
 			compatible = "gw,gsc-fan";
-			#address-cells = <1>;
-			#size-cells = <0>;
 			reg = <0x0a>;
 		};
 	};
@@ -309,7 +307,6 @@
 		st,drdy-int-pin = <1>;
 		interrupt-parent = <&gpio7>;
 		interrupts = <13 0>;
-		interrupt-names = "INT1";
 	};
 };
 
@@ -572,7 +569,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+	pinctrl_usdhc3_100mhz: usdhc3-100mhz-grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170b9
 			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100b9
@@ -585,7 +582,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+	pinctrl_usdhc3_200mhz: usdhc3-200mhz-grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170f9
 			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100f9
diff --git a/arch/arm/boot/dts/imx6qdl-gw5913.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5913.dtsi
index 8e23cec7149e..4e4dce5adc15 100644
--- a/arch/arm/boot/dts/imx6qdl-gw5913.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-gw5913.dtsi
@@ -24,13 +24,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		user-pb {
+		key-user-pb {
 			label = "user_pb";
-			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
+			gpios = <&gsc_gpio 2 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_0>;
 		};
 
-		user-pb1x {
+		key-user-pb1x {
 			label = "user_pb1x";
 			linux,code = <BTN_1>;
 			interrupt-parent = <&gsc>;
@@ -44,21 +44,21 @@
 			interrupts = <1>;
 		};
 
-		eeprom-wp {
+		key-eeprom-wp {
 			label = "eeprom_wp";
 			linux,code = <BTN_3>;
 			interrupt-parent = <&gsc>;
 			interrupts = <2>;
 		};
 
-		tamper {
+		key-tamper {
 			label = "tamper";
 			linux,code = <BTN_4>;
 			interrupt-parent = <&gsc>;
 			interrupts = <5>;
 		};
 
-		switch-hold {
+		key-switch-hold {
 			label = "switch_hold";
 			linux,code = <BTN_5>;
 			interrupt-parent = <&gsc>;
@@ -71,14 +71,14 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		led0: user1 {
+		led0: led-user1 {
 			label = "user1";
 			gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 
-		led1: user2 {
+		led1: led-user2 {
 			label = "user2";
 			gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
 			default-state = "off";
@@ -141,6 +141,7 @@
 		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
+		#address-cells = <1>;
 		#size-cells = <0>;
 
 		adc {
diff --git a/arch/arm/boot/dts/imx6qdl-hummingboard.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-hummingboard.dtsi
index 2ffb21dd89f2..6b737360a532 100644
--- a/arch/arm/boot/dts/imx6qdl-hummingboard.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-hummingboard.dtsi
@@ -41,6 +41,11 @@
 #include <dt-bindings/sound/fsl-imx-audmux.h>
 
 / {
+	aliases {
+		rtc0 = &carrier_rtc;
+		rtc1 = &snvs_rtc;
+	};
+
 	/* Will be filled by the bootloader */
 	memory@10000000 {
 		device_type = "memory";
@@ -135,19 +140,24 @@
 		};
 	};
 
+	spdif_out: spdif-out {
+		compatible = "linux,spdif-dit";
+		#sound-dai-cells = <0>;
+	};
+
 	sound-spdif {
 		compatible = "fsl,imx-audio-spdif";
 		model = "On-board SPDIF";
 		/* IMX6 doesn't implement this yet */
-		spdif-controller = <&spdif>;
-		spdif-out;
+		audio-cpu = <&spdif>;
+		audio-codec = <&spdif_out>;
 	};
 };
 
 &audmux {
 	status = "okay";
 
-	ssi1 {
+	mux-ssi1 {
 		fsl,audmux-port = <0>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_SYN |
@@ -159,7 +169,7 @@
 		>;
 	};
 
-	pins5 {
+	mux-pins5 {
 		fsl,audmux-port = <4>;
 		fsl,port-config = <
 			IMX_AUDMUX_V2_PTCR_SYN
@@ -187,7 +197,7 @@
 	status = "okay";
 
 	/* Pro baseboard model */
-	rtc@68 {
+	carrier_rtc: rtc@68 {
 		compatible = "nxp,pcf8523";
 		reg = <0x68>;
 	};
@@ -213,100 +223,98 @@
 };
 
 &iomuxc {
-	hummingboard {
-		pinctrl_hummingboard_flexcan1: hummingboard-flexcan1 {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_CLK__FLEXCAN1_RX 0x80000000
-				MX6QDL_PAD_SD3_CMD__FLEXCAN1_TX 0x80000000
-			>;
-		};
+	pinctrl_hummingboard_flexcan1: hummingboard-flexcan1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CLK__FLEXCAN1_RX 0x80000000
+			MX6QDL_PAD_SD3_CMD__FLEXCAN1_TX 0x80000000
+		>;
+	};
 
-		pinctrl_hummingboard_gpio3_5: hummingboard-gpio3_5 {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_DA5__GPIO3_IO05 0x1b0b1
-			>;
-		};
+	pinctrl_hummingboard_gpio3_5: hummingboard-gpio3_5grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_DA5__GPIO3_IO05 0x1b0b1
+		>;
+	};
 
-		pinctrl_hummingboard_hdmi: hummingboard-hdmi {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0
-			>;
-		};
+	pinctrl_hummingboard_hdmi: hummingboard-hdmigrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0
+		>;
+	};
 
-		pinctrl_hummingboard_i2c1: hummingboard-i2c1 {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
-				MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
-			>;
-		};
+	pinctrl_hummingboard_i2c1: hummingboard-i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+			MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+		>;
+	};
 
-		pinctrl_hummingboard_i2c2: hummingboard-i2c2 {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
-				MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
-			>;
-		};
+	pinctrl_hummingboard_i2c2: hummingboard-i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+		>;
+	};
 
-		pinctrl_hummingboard_pcie_reset: hummingboard-pcie-reset {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_DA4__GPIO3_IO04 0x1b0b1
-			>;
-		};
+	pinctrl_hummingboard_pcie_reset: hummingboard-pcie-resetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_DA4__GPIO3_IO04 0x1b0b1
+		>;
+	};
 
-		pinctrl_hummingboard_pwm1: pwm1grp {
-			fsl,pins = <MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b1>;
-		};
+	pinctrl_hummingboard_pwm1: pwm1grp {
+		fsl,pins = <MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b1>;
+	};
 
-		pinctrl_hummingboard_sgtl5000: hummingboard-sgtl5000 {
-			fsl,pins = <
-				MX6QDL_PAD_DISP0_DAT19__AUD5_RXD 0x130b0
-				MX6QDL_PAD_KEY_COL0__AUD5_TXC 0x130b0
-				MX6QDL_PAD_KEY_ROW0__AUD5_TXD 0x110b0
-				MX6QDL_PAD_KEY_COL1__AUD5_TXFS 0x130b0
-				MX6QDL_PAD_GPIO_5__CCM_CLKO1 0x130b0
-			>;
-		};
+	pinctrl_hummingboard_sgtl5000: hummingboard-sgtl5000grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT19__AUD5_RXD 0x130b0
+			MX6QDL_PAD_KEY_COL0__AUD5_TXC 0x130b0
+			MX6QDL_PAD_KEY_ROW0__AUD5_TXD 0x110b0
+			MX6QDL_PAD_KEY_COL1__AUD5_TXFS 0x130b0
+			MX6QDL_PAD_GPIO_5__CCM_CLKO1 0x130b0
+		>;
+	};
 
-		pinctrl_hummingboard_spdif: hummingboard-spdif {
-			fsl,pins = <MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x13091>;
-		};
+	pinctrl_hummingboard_spdif: hummingboard-spdifgrp {
+		fsl,pins = <MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x13091>;
+	};
 
-		pinctrl_hummingboard_usbh1_vbus: hummingboard-usbh1-vbus {
-			fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0>;
-		};
+	pinctrl_hummingboard_usbh1_vbus: hummingboard-usbh1-vbusgrp {
+		fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0>;
+	};
 
-		pinctrl_hummingboard_usbotg_id: hummingboard-usbotg-id {
-			/*
-			 * We want it pulled down for a fixed host connection.
-			 */
-			fsl,pins = <MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x13059>;
-		};
+	pinctrl_hummingboard_usbotg_id: hummingboard-usbotg-idgrp {
+		/*
+		 * We want it pulled down for a fixed host connection.
+		 */
+		fsl,pins = <MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x13059>;
+	};
 
-		pinctrl_hummingboard_usbotg_vbus: hummingboard-usbotg-vbus {
-			fsl,pins = <MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0>;
-		};
+	pinctrl_hummingboard_usbotg_vbus: hummingboard-usbotg-vbusgrp {
+		fsl,pins = <MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0>;
+	};
 
-		pinctrl_hummingboard_usdhc2_aux: hummingboard-usdhc2-aux {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_4__GPIO1_IO04    0x1f071
-			>;
-		};
+	pinctrl_hummingboard_usdhc2_aux: hummingboard-usdhc2-auxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04    0x1f071
+		>;
+	};
 
-		pinctrl_hummingboard_usdhc2: hummingboard-usdhc2 {
-			fsl,pins = <
-				MX6QDL_PAD_SD2_CMD__SD2_CMD    0x17059
-				MX6QDL_PAD_SD2_CLK__SD2_CLK    0x10059
-				MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
-				MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
-				MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
-				MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x13059
-			>;
-		};
-		pinctrl_hummingboard_vmmc: hummingboard-vmmc {
-			fsl,pins = <
-				MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x1b0b0
-			>;
-		};
+	pinctrl_hummingboard_usdhc2: hummingboard-usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD    0x17059
+			MX6QDL_PAD_SD2_CLK__SD2_CLK    0x10059
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x13059
+		>;
+	};
+	pinctrl_hummingboard_vmmc: hummingboard-vmmcgrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x1b0b0
+		>;
 	};
 };
 
@@ -324,7 +332,6 @@
 };
 
 &pwm2 {
-	 pinctrl-names = "default";
 	 status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-hummingboard2-emmc.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-hummingboard2-emmc.dtsi
index f400405381a7..c3efb001c515 100644
--- a/arch/arm/boot/dts/imx6qdl-hummingboard2-emmc.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-hummingboard2-emmc.dtsi
@@ -42,22 +42,20 @@
  */
 
 &iomuxc {
-	hummingboard2 {
-		pinctrl_hummingboard2_usdhc3: hummingboard2-usdhc3 {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_CMD__SD3_CMD    0x17059
-				MX6QDL_PAD_SD3_CLK__SD3_CLK    0x10059
-				MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
-				MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
-				MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
-				MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
-				MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059
-				MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059
-				MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059
-				MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
-				MX6QDL_PAD_SD3_RST__SD3_RESET  0x17059
-			>;
-		};
+	pinctrl_hummingboard2_usdhc3: hummingboard2-usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD    0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK    0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
+			MX6QDL_PAD_SD3_RST__SD3_RESET  0x17059
+		>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-hummingboard2.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-hummingboard2.dtsi
index eb1ad28946d3..3069e1738ba2 100644
--- a/arch/arm/boot/dts/imx6qdl-hummingboard2.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-hummingboard2.dtsi
@@ -41,6 +41,11 @@
 #include <dt-bindings/sound/fsl-imx-audmux.h>
 
 / {
+	aliases {
+		rtc0 = &pcf8523;
+		rtc1 = &snvs_rtc;
+	};
+
 	/* Will be filled by the bootloader */
 	memory@10000000 {
 		device_type = "memory";
@@ -179,7 +184,7 @@
 &audmux {
 	status = "okay";
 
-	ssi1 {
+	mux-ssi1 {
 		fsl,audmux-port = <0>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_SYN |
@@ -191,7 +196,7 @@
 		>;
 	};
 
-	pins5 {
+	mux-pins5 {
 		fsl,audmux-port = <4>;
 		fsl,port-config = <
 			IMX_AUDMUX_V2_PTCR_SYN
@@ -256,258 +261,256 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hog>;
 
-	hummingboard2 {
-		pinctrl_hog: hoggrp {
+	pinctrl_hog: hoggrp {
 		fsl,pins = <
-				/*
-				 * 36 pin headers GPIO description. The pins
-				 * numbering as following -
-				 *
-				 * 	3.2v	5v	74	75
-				 *	73	72	71	70
-				 *	69	68	67	66
-				 *
-				 *	77	78	79	76
-				 *	65	64	61	60
-				 *	53	52	51	50
-				 *	49	48	166	132
-				 *	95	94	90	91
-				 *	GND	54	24	204
-				 *
-				 * The GPIO numbers can be extracted using
-				 * signal name from below.
-				 * Example -
-				 * MX6QDL_PAD_EIM_DA10__GPIO3_IO10 is
-				 * GPIO(3,10) which is (3-1)*32+10 = gpio 74
-				 *
-				 * i.e. The mapping of GPIO(X,Y) to Linux gpio
-				 * number is : gpio number = (X-1) * 32 + Y
-				 */
-				/* DI1_PIN15 */
-				MX6QDL_PAD_EIM_DA10__GPIO3_IO10 0x400130b1
-				/* DI1_PIN02 */
-				MX6QDL_PAD_EIM_DA11__GPIO3_IO11 0x400130b1
-				/* DISP1_DATA00 */
-				MX6QDL_PAD_EIM_DA9__GPIO3_IO09 0x400130b1
-				/* DISP1_DATA01 */
-				MX6QDL_PAD_EIM_DA8__GPIO3_IO08 0x400130b1
-				/* DISP1_DATA02 */
-				MX6QDL_PAD_EIM_DA7__GPIO3_IO07 0x400130b1
-				/* DISP1_DATA03 */
-				MX6QDL_PAD_EIM_DA6__GPIO3_IO06 0x400130b1
-				/* DISP1_DATA04 */
-				MX6QDL_PAD_EIM_DA5__GPIO3_IO05 0x400130b1
-				/* DISP1_DATA05 */
-				MX6QDL_PAD_EIM_DA4__GPIO3_IO04 0x400130b1
-				/* DISP1_DATA06 */
-				MX6QDL_PAD_EIM_DA3__GPIO3_IO03 0x400130b1
-				/* DISP1_DATA07 */
-				MX6QDL_PAD_EIM_DA2__GPIO3_IO02 0x400130b1
-				/* DI1_D0_CS */
-				MX6QDL_PAD_EIM_DA13__GPIO3_IO13 0x400130b1
-				/* DI1_D1_CS */
-				MX6QDL_PAD_EIM_DA14__GPIO3_IO14 0x400130b1
-				/* DI1_PIN01 */
-				MX6QDL_PAD_EIM_DA15__GPIO3_IO15 0x400130b1
-				/* DI1_PIN03 */
-				MX6QDL_PAD_EIM_DA12__GPIO3_IO12 0x400130b1
-				/* DISP1_DATA08 */
-				MX6QDL_PAD_EIM_DA1__GPIO3_IO01 0x400130b1
-				/* DISP1_DATA09 */
-				MX6QDL_PAD_EIM_DA0__GPIO3_IO00 0x400130b1
-				/* DISP1_DATA10 */
-				MX6QDL_PAD_EIM_EB1__GPIO2_IO29 0x400130b1
-				/* DISP1_DATA11 */
-				MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0x400130b1
-				/* DISP1_DATA12 */
-				MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x400130b1
-				/* DISP1_DATA13 */
-				MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x400130b1
-				/* DISP1_DATA14 */
-				MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x400130b1
-				/* DISP1_DATA15 */
-				MX6QDL_PAD_EIM_A20__GPIO2_IO18 0x400130b1
-				/* DISP1_DATA16 */
-				MX6QDL_PAD_EIM_A21__GPIO2_IO17 0x400130b1
-				/* DISP1_DATA17 */
-				MX6QDL_PAD_EIM_A22__GPIO2_IO16 0x400130b1
-				/* DISP1_DATA18 */
-				MX6QDL_PAD_EIM_A23__GPIO6_IO06 0x400130b1
-				/* DISP1_DATA19 */
-				MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x400130b1
-				/* DISP1_DATA20 */
-				MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x400130b1
-				/* DISP1_DATA21 */
-				MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x400130b1
-				/* DISP1_DATA22 */
-				MX6QDL_PAD_EIM_D26__GPIO3_IO26 0x400130b1
-				/* DISP1_DATA23 */
-				MX6QDL_PAD_EIM_D27__GPIO3_IO27 0x400130b1
-				/* DI1_DISP_CLK */
-				MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x400130b1
-				/* SPDIF_IN */
-				MX6QDL_PAD_ENET_RX_ER__GPIO1_IO24 0x400130b1
-				/* SPDIF_OUT */
-				MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x400130b1
-
-				/* MikroBUS GPIO pin number 10 */
-				MX6QDL_PAD_EIM_LBA__GPIO2_IO27 0x400130b1
-			>;
-		};
+			/*
+			 * 36 pin headers GPIO description. The pins
+			 * numbering as following -
+			 *
+			 * 	3.2v	5v	74	75
+			 *	73	72	71	70
+			 *	69	68	67	66
+			 *
+			 *	77	78	79	76
+			 *	65	64	61	60
+			 *	53	52	51	50
+			 *	49	48	166	132
+			 *	95	94	90	91
+			 *	GND	54	24	204
+			 *
+			 * The GPIO numbers can be extracted using
+			 * signal name from below.
+			 * Example -
+			 * MX6QDL_PAD_EIM_DA10__GPIO3_IO10 is
+			 * GPIO(3,10) which is (3-1)*32+10 = gpio 74
+			 *
+			 * i.e. The mapping of GPIO(X,Y) to Linux gpio
+			 * number is : gpio number = (X-1) * 32 + Y
+			 */
+			/* DI1_PIN15 */
+			MX6QDL_PAD_EIM_DA10__GPIO3_IO10 0x400130b1
+			/* DI1_PIN02 */
+			MX6QDL_PAD_EIM_DA11__GPIO3_IO11 0x400130b1
+			/* DISP1_DATA00 */
+			MX6QDL_PAD_EIM_DA9__GPIO3_IO09 0x400130b1
+			/* DISP1_DATA01 */
+			MX6QDL_PAD_EIM_DA8__GPIO3_IO08 0x400130b1
+			/* DISP1_DATA02 */
+			MX6QDL_PAD_EIM_DA7__GPIO3_IO07 0x400130b1
+			/* DISP1_DATA03 */
+			MX6QDL_PAD_EIM_DA6__GPIO3_IO06 0x400130b1
+			/* DISP1_DATA04 */
+			MX6QDL_PAD_EIM_DA5__GPIO3_IO05 0x400130b1
+			/* DISP1_DATA05 */
+			MX6QDL_PAD_EIM_DA4__GPIO3_IO04 0x400130b1
+			/* DISP1_DATA06 */
+			MX6QDL_PAD_EIM_DA3__GPIO3_IO03 0x400130b1
+			/* DISP1_DATA07 */
+			MX6QDL_PAD_EIM_DA2__GPIO3_IO02 0x400130b1
+			/* DI1_D0_CS */
+			MX6QDL_PAD_EIM_DA13__GPIO3_IO13 0x400130b1
+			/* DI1_D1_CS */
+			MX6QDL_PAD_EIM_DA14__GPIO3_IO14 0x400130b1
+			/* DI1_PIN01 */
+			MX6QDL_PAD_EIM_DA15__GPIO3_IO15 0x400130b1
+			/* DI1_PIN03 */
+			MX6QDL_PAD_EIM_DA12__GPIO3_IO12 0x400130b1
+			/* DISP1_DATA08 */
+			MX6QDL_PAD_EIM_DA1__GPIO3_IO01 0x400130b1
+			/* DISP1_DATA09 */
+			MX6QDL_PAD_EIM_DA0__GPIO3_IO00 0x400130b1
+			/* DISP1_DATA10 */
+			MX6QDL_PAD_EIM_EB1__GPIO2_IO29 0x400130b1
+			/* DISP1_DATA11 */
+			MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0x400130b1
+			/* DISP1_DATA12 */
+			MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x400130b1
+			/* DISP1_DATA13 */
+			MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x400130b1
+			/* DISP1_DATA14 */
+			MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x400130b1
+			/* DISP1_DATA15 */
+			MX6QDL_PAD_EIM_A20__GPIO2_IO18 0x400130b1
+			/* DISP1_DATA16 */
+			MX6QDL_PAD_EIM_A21__GPIO2_IO17 0x400130b1
+			/* DISP1_DATA17 */
+			MX6QDL_PAD_EIM_A22__GPIO2_IO16 0x400130b1
+			/* DISP1_DATA18 */
+			MX6QDL_PAD_EIM_A23__GPIO6_IO06 0x400130b1
+			/* DISP1_DATA19 */
+			MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x400130b1
+			/* DISP1_DATA20 */
+			MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x400130b1
+			/* DISP1_DATA21 */
+			MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x400130b1
+			/* DISP1_DATA22 */
+			MX6QDL_PAD_EIM_D26__GPIO3_IO26 0x400130b1
+			/* DISP1_DATA23 */
+			MX6QDL_PAD_EIM_D27__GPIO3_IO27 0x400130b1
+			/* DI1_DISP_CLK */
+			MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x400130b1
+			/* SPDIF_IN */
+			MX6QDL_PAD_ENET_RX_ER__GPIO1_IO24 0x400130b1
+			/* SPDIF_OUT */
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x400130b1
+
+			/* MikroBUS GPIO pin number 10 */
+			MX6QDL_PAD_EIM_LBA__GPIO2_IO27 0x400130b1
+		>;
+	};
 
-		pinctrl_hummingboard2_ecspi2: hummingboard2-ecspi2grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_OE__ECSPI2_MISO	0x100b1
-				MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI	0x100b1
-				MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK	0x100b1
-				MX6QDL_PAD_EIM_RW__GPIO2_IO26	0x000b1 /* CS */
-			>;
-		};
+	pinctrl_hummingboard2_ecspi2: hummingboard2-ecspi2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_OE__ECSPI2_MISO	0x100b1
+			MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI	0x100b1
+			MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK	0x100b1
+			MX6QDL_PAD_EIM_RW__GPIO2_IO26	0x000b1 /* CS */
+		>;
+	};
 
-		pinctrl_hummingboard2_gpio7_9: hummingboard2-gpio7_9 {
-			fsl,pins = <
-				MX6QDL_PAD_SD4_CMD__GPIO7_IO09 0x80000000
-			>;
-		};
+	pinctrl_hummingboard2_gpio7_9: hummingboard2-gpio7_9grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__GPIO7_IO09 0x80000000
+		>;
+	};
 
-		pinctrl_hummingboard2_hdmi: hummingboard2-hdmi {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0
-			>;
-		};
+	pinctrl_hummingboard2_hdmi: hummingboard2-hdmigrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0
+		>;
+	};
 
-		pinctrl_hummingboard2_i2c1: hummingboard2-i2c1 {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
-				MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
-			>;
-		};
+	pinctrl_hummingboard2_i2c1: hummingboard2-i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+			MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+		>;
+	};
 
-		pinctrl_hummingboard2_i2c2: hummingboard2-i2c2 {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
-				MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
-			>;
-		};
+	pinctrl_hummingboard2_i2c2: hummingboard2-i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+		>;
+	};
 
-		pinctrl_hummingboard2_i2c3: hummingboard2-i2c3 {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1
-				MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
-			>;
-		};
+	pinctrl_hummingboard2_i2c3: hummingboard2-i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1
+			MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
+		>;
+	};
 
-		pinctrl_hummingboard2_mipi: hummingboard2_mipi {
-			fsl,pins = <
-				MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x4001b8b1
-				MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x4001b8b1
-				MX6QDL_PAD_NANDF_CS2__CCM_CLKO2 0x130b0
-			>;
-		};
+	pinctrl_hummingboard2_mipi: hummingboard2_mipigrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x4001b8b1
+			MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x4001b8b1
+			MX6QDL_PAD_NANDF_CS2__CCM_CLKO2 0x130b0
+		>;
+	};
 
-		pinctrl_hummingboard2_pcie_reset: hummingboard2-pcie-reset {
-			fsl,pins = <
-				MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b1
-			>;
-		};
+	pinctrl_hummingboard2_pcie_reset: hummingboard2-pcie-resetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b1
+		>;
+	};
 
-		pinctrl_hummingboard2_pwm1: pwm1grp {
-			fsl,pins = <
-				MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b1
-			>;
-		};
+	pinctrl_hummingboard2_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b1
+		>;
+	};
 
-		pinctrl_hummingboard2_pwm3: pwm3grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1
-			>;
-		};
+	pinctrl_hummingboard2_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1
+		>;
+	};
 
-		pinctrl_hummingboard2_sgtl5000: hummingboard2-sgtl5000 {
-			fsl,pins = <
-				MX6QDL_PAD_DISP0_DAT19__AUD5_RXD 0x130b0
-				MX6QDL_PAD_KEY_COL0__AUD5_TXC 0x130b0
-				MX6QDL_PAD_KEY_ROW0__AUD5_TXD 0x110b0
-				MX6QDL_PAD_KEY_COL1__AUD5_TXFS 0x130b0
-				MX6QDL_PAD_GPIO_5__CCM_CLKO1 0x130b0
-			>;
-		};
+	pinctrl_hummingboard2_sgtl5000: hummingboard2-sgtl5000grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT19__AUD5_RXD 0x130b0
+			MX6QDL_PAD_KEY_COL0__AUD5_TXC 0x130b0
+			MX6QDL_PAD_KEY_ROW0__AUD5_TXD 0x110b0
+			MX6QDL_PAD_KEY_COL1__AUD5_TXFS 0x130b0
+			MX6QDL_PAD_GPIO_5__CCM_CLKO1 0x130b0
+		>;
+	};
 
-		pinctrl_hummingboard2_usbh1_vbus: hummingboard2-usbh1-vbus {
-			fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0>;
-		};
+	pinctrl_hummingboard2_usbh1_vbus: hummingboard2-usbh1-vbusgrp {
+		fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0>;
+	};
 
-		pinctrl_hummingboard2_usbh2_vbus: hummingboard2-usbh2-vbus {
-			fsl,pins = <MX6QDL_PAD_SD4_DAT5__GPIO2_IO13 0x1b0b0>;
-		};
+	pinctrl_hummingboard2_usbh2_vbus: hummingboard2-usbh2-vbusgrp {
+		fsl,pins = <MX6QDL_PAD_SD4_DAT5__GPIO2_IO13 0x1b0b0>;
+	};
 
-		pinctrl_hummingboard2_usbh3_vbus: hummingboard2-usbh3-vbus {
-			fsl,pins = <MX6QDL_PAD_SD4_CLK__GPIO7_IO10 0x1b0b0>;
-		};
+	pinctrl_hummingboard2_usbh3_vbus: hummingboard2-usbh3-vbusgrp {
+		fsl,pins = <MX6QDL_PAD_SD4_CLK__GPIO7_IO10 0x1b0b0>;
+	};
 
-		pinctrl_hummingboard2_usbotg_id: hummingboard2-usbotg-id {
-			/*
-			 * We want it pulled down for a fixed host connection.
-			 */
-			fsl,pins = <MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059>;
-		};
+	pinctrl_hummingboard2_usbotg_id: hummingboard2-usbotg-idgrp {
+		/*
+		 * We want it pulled down for a fixed host connection.
+		 */
+		fsl,pins = <MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059>;
+	};
 
-		pinctrl_hummingboard2_usbotg_vbus: hummingboard2-usbotg-vbus {
-			fsl,pins = <MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0>;
-		};
+	pinctrl_hummingboard2_usbotg_vbus: hummingboard2-usbotg-vbusgrp {
+		fsl,pins = <MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0>;
+	};
 
-		pinctrl_hummingboard2_usdhc2_aux: hummingboard2-usdhc2-aux {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_4__GPIO1_IO04    0x1f071
-				MX6QDL_PAD_KEY_ROW1__SD2_VSELECT 0x1b071
-			>;
-		};
+	pinctrl_hummingboard2_usdhc2_aux: hummingboard2-usdhc2-auxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04    0x1f071
+			MX6QDL_PAD_KEY_ROW1__SD2_VSELECT 0x1b071
+		>;
+	};
 
-		pinctrl_hummingboard2_usdhc2: hummingboard2-usdhc2 {
-			fsl,pins = <
-				MX6QDL_PAD_SD2_CMD__SD2_CMD    0x17059
-				MX6QDL_PAD_SD2_CLK__SD2_CLK    0x10059
-				MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
-				MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
-				MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
-				MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x13059
-			>;
-		};
+	pinctrl_hummingboard2_usdhc2: hummingboard2-usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD    0x17059
+			MX6QDL_PAD_SD2_CLK__SD2_CLK    0x10059
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x13059
+		>;
+	};
 
-		pinctrl_hummingboard2_usdhc2_100mhz: hummingboard2-usdhc2-100mhz {
-			fsl,pins = <
-				MX6QDL_PAD_SD2_CMD__SD2_CMD    0x170b9
-				MX6QDL_PAD_SD2_CLK__SD2_CLK    0x100b9
-				MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
-				MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
-				MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
-				MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x130b9
-			>;
-		};
+	pinctrl_hummingboard2_usdhc2_100mhz: hummingboard2-usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD    0x170b9
+			MX6QDL_PAD_SD2_CLK__SD2_CLK    0x100b9
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x130b9
+		>;
+	};
 
-		pinctrl_hummingboard2_usdhc2_200mhz: hummingboard2-usdhc2-200mhz {
-			fsl,pins = <
-				MX6QDL_PAD_SD2_CMD__SD2_CMD    0x170f9
-				MX6QDL_PAD_SD2_CLK__SD2_CLK    0x100f9
-				MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170f9
-				MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170f9
-				MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170f9
-				MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x130f9
-			>;
-		};
+	pinctrl_hummingboard2_usdhc2_200mhz: hummingboard2-usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD    0x170f9
+			MX6QDL_PAD_SD2_CLK__SD2_CLK    0x100f9
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170f9
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170f9
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170f9
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x130f9
+		>;
+	};
 
-		pinctrl_hummingboard2_vmmc: hummingboard2-vmmc {
-			fsl,pins = <
-				MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x1b0b0
-			>;
-		};
+	pinctrl_hummingboard2_vmmc: hummingboard2-vmmcgrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x1b0b0
+		>;
+	};
 
-		pinctrl_hummingboard2_uart3: hummingboard2-uart3 {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D25__UART3_TX_DATA	0x1b0b1
-				MX6QDL_PAD_EIM_D24__UART3_RX_DATA	0x40013000
-			>;
-		};
+	pinctrl_hummingboard2_uart3: hummingboard2-uart3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D25__UART3_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D24__UART3_RX_DATA	0x40013000
+		>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-icore-1.5.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-icore-1.5.dtsi
index 0fd7f2e24d9c..0fd7f2e24d9c 100644
--- a/arch/arm/boot/dts/imx6qdl-icore-1.5.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-icore-1.5.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-icore-rqs.dtsi
index a4217f564a53..dff184a119f3 100644
--- a/arch/arm/boot/dts/imx6qdl-icore-rqs.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-icore-rqs.dtsi
@@ -118,7 +118,7 @@
 	pinctrl-0 = <&pinctrl_audmux>;
 	status = "okay";
 
-	audmux_ssi1 {
+	mux-ssi1 {
 		fsl,audmux-port = <MX51_AUDMUX_PORT1_SSI0>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_TFSDIR |
@@ -130,7 +130,7 @@
 		>;
 	};
 
-	audmux_aud4 {
+	mux-aud4 {
 		fsl,audmux-port = <MX51_AUDMUX_PORT4>;
 		fsl,port-config = <
 			IMX_AUDMUX_V2_PTCR_SYN
@@ -262,7 +262,7 @@
 	pinctrl-0 = <&pinctrl_usdhc3>;
 	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
 	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
-	vmcc-supply = <&reg_sd3_vmmc>;
+	vmmc-supply = <&reg_sd3_vmmc>;
 	cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
 	bus-width = <4>;
 	no-1-8-v;
@@ -274,7 +274,7 @@
 	pinctrl-0 = <&pinctrl_usdhc4>;
 	pinctrl-1 = <&pinctrl_usdhc4_100mhz>;
 	pinctrl-2 = <&pinctrl_usdhc4_200mhz>;
-	vmcc-supply = <&reg_sd4_vmmc>;
+	vmmc-supply = <&reg_sd4_vmmc>;
 	bus-width = <8>;
 	no-1-8-v;
 	non-removable;
@@ -397,7 +397,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_100mhz: usdhc3grp_100mhz {
+	pinctrl_usdhc3_100mhz: usdhc3-100mhz-grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD    0x170B1
 			MX6QDL_PAD_SD3_CLK__SD3_CLK    0x100B1
@@ -408,7 +408,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_200mhz: usdhc3grp_200mhz {
+	pinctrl_usdhc3_200mhz: usdhc3-200mhz-grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD    0x170F9
 			MX6QDL_PAD_SD3_CLK__SD3_CLK    0x100F9
@@ -434,7 +434,7 @@
 		>;
 	};
 
-	pinctrl_usdhc4_100mhz: usdhc4grp_100mhz {
+	pinctrl_usdhc4_100mhz: usdhc4-100mhz-grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD4_CMD__SD4_CMD    0x170B1
 			MX6QDL_PAD_SD4_CLK__SD4_CLK    0x100B1
@@ -449,7 +449,7 @@
 		>;
 	};
 
-	pinctrl_usdhc4_200mhz: usdhc4grp_200mhz {
+	pinctrl_usdhc4_200mhz: usdhc4-200mhz-grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD4_CMD__SD4_CMD    0x170F9
 			MX6QDL_PAD_SD4_CLK__SD4_CLK    0x100F9
diff --git a/arch/arm/boot/dts/imx6qdl-icore.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-icore.dtsi
index 23c318d9636f..9975b6ee433d 100644
--- a/arch/arm/boot/dts/imx6qdl-icore.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-icore.dtsi
@@ -20,7 +20,7 @@
 
 	backlight_lvds: backlight-lvds {
 		compatible = "pwm-backlight";
-		pwms = <&pwm3 0 100000>;
+		pwms = <&pwm3 0 100000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 	};
@@ -109,7 +109,7 @@
 	status = "okay";
 
 
-	audmux_ssi1 {
+	mux-ssi1 {
 		fsl,audmux-port = <MX51_AUDMUX_PORT1_SSI0>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_TFSDIR |
@@ -121,7 +121,7 @@
 		>;
 	};
 
-	audmux_aud4 {
+	mux-aud4 {
 		fsl,audmux-port = <MX51_AUDMUX_PORT4>;
 		fsl,port-config = <
 			IMX_AUDMUX_V2_PTCR_SYN
@@ -245,7 +245,6 @@
 };
 
 &pwm3 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-kontron-samx6i-ads2.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-kontron-samx6i-ads2.dtsi
new file mode 100644
index 000000000000..b4a79245b7b6
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-kontron-samx6i-ads2.dtsi
@@ -0,0 +1,148 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree include for the Kontron SMARC-sAMX6i board on a SMARC Eval
+ * 2.0 carrier (ADS2).
+ *
+ */
+
+/ {
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	sound {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&dailink_master>;
+		simple-audio-card,frame-master = <&dailink_master>;
+		simple-audio-card,widgets =
+			"Headphone", "Headphone Jack",
+			"Line", "Line Out Jack",
+			"Microphone", "Microphone Jack",
+			"Line", "Line In Jack";
+		simple-audio-card,routing =
+			"Line Out Jack", "LINEOUTR",
+			"Line Out Jack", "LINEOUTL",
+			"Headphone Jack", "HPOUTR",
+			"Headphone Jack", "HPOUTL",
+			"IN1L", "Line In Jack",
+			"IN1R", "Line In Jack",
+			"Microphone Jack", "MICBIAS",
+			"IN2L", "Microphone Jack",
+			"IN2R", "Microphone Jack";
+
+		simple-audio-card,cpu {
+			sound-dai = <&ssi1>;
+		};
+
+		dailink_master: simple-audio-card,codec {
+			sound-dai = <&wm8904>;
+		};
+	};
+
+	reg_codec_mic: regulator-codec-mic {
+		compatible = "regulator-fixed";
+		regulator-name = "V_3V3_MIC";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	reg_codec_1p8v: regulator-codec-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "V_1V8_S0_CODEC";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&audmux {
+	status = "okay";
+};
+
+&can1 {
+	status = "okay";
+};
+
+&can2 {
+	status = "okay";
+};
+
+&ecspi4 {
+	flash@1 {
+		compatible = "jedec,spi-nor";
+		reg = <1>;
+		spi-max-frequency = <100000000>;
+		m25p,fast-read;
+	};
+};
+
+&fec {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+
+	wm8904: audio-codec@1a {
+		compatible = "wlf,wm8904";
+		reg = <0x1a>;
+		#sound-dai-cells = <0>;
+		clocks = <&clks IMX6QDL_CLK_CKO2>;
+		clock-names = "mclk";
+		AVDD-supply = <&reg_codec_1p8v>;
+		CPVDD-supply = <&reg_codec_1p8v>;
+		DBVDD-supply = <&reg_codec_1p8v>;
+		DCVDD-supply = <&reg_codec_1p8v>;
+		MICVDD-supply = <&reg_codec_mic>;
+	};
+};
+
+&i2c3 {
+	eeprom@57 {
+		compatible = "atmel,24c64";
+		reg = <0x57>;
+		pagesize = <32>;
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&ssi1 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbotg {
+	status = "okay";
+};
+
+&usdhc3 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-kontron-samx6i.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-kontron-samx6i.dtsi
index b167b33bd108..c771f87b10df 100644
--- a/arch/arm/boot/dts/imx6qdl-kontron-samx6i.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-kontron-samx6i.dtsi
@@ -51,24 +51,26 @@
 		vin-supply = <&reg_3p3v_s5>;
 	};
 
-	reg_3p3v_s0: regulator-3p3v-s0 {
+	reg_3p3v_s5: regulator-3p3v-s5 {
 		compatible = "regulator-fixed";
-		regulator-name = "V_3V3_S0";
+		regulator-name = "V_3V3_S5";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 		regulator-always-on;
 		regulator-boot-on;
-		vin-supply = <&reg_3p3v_s5>;
+		vin-supply = <&reg_smarc_suppy>;
 	};
 
-	reg_3p3v_s5: regulator-3p3v-s5 {
+	reg_sdio: regulator-sdio {
 		compatible = "regulator-fixed";
-		regulator-name = "V_3V3_S5";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_sdio>;
+		regulator-name = "V_3V3_SD";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-		regulator-boot-on;
-		vin-supply = <&reg_smarc_suppy>;
+		gpio = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		off-on-delay-us = <20000>;
 	};
 
 	reg_smarc_lcdbklt: regulator-smarc-lcdbklt {
@@ -147,7 +149,7 @@
 		status = "disabled";
 	};
 
-	i2c_intern: i2c-gpio-intern {
+	i2c_intern: i2c-0 {
 		compatible = "i2c-gpio";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_i2c_gpio_intern>;
@@ -158,7 +160,7 @@
 		#size-cells = <0>;
 	};
 
-	i2c_lcd: i2c-gpio-lcd {
+	i2c_lcd: i2c-1 {
 		compatible = "i2c-gpio";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_i2c_gpio_lcd>;
@@ -170,7 +172,7 @@
 		status = "disabled";
 	};
 
-	i2c_cam: i2c-gpio-cam {
+	i2c_cam: i2c-2 {
 		compatible = "i2c-gpio";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_i2c_gpio_cam>;
@@ -188,7 +190,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_audmux>;
 
-	audmux_ssi1 {
+	mux-ssi1 {
 		fsl,audmux-port = <MX51_AUDMUX_PORT1_SSI0>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_TFSEL(MX51_AUDMUX_PORT3) |
@@ -200,7 +202,7 @@
 		>;
 	};
 
-	audmux_adu3 {
+	mux-aud3 {
 		fsl,audmux-port = <MX51_AUDMUX_PORT3>;
 		fsl,port-config = <
 			IMX_AUDMUX_V2_PTCR_SYN
@@ -208,7 +210,7 @@
 		>;
 	};
 
-	audmux_ssi2 {
+	mux-ssi2 {
 		fsl,audmux-port = <MX51_AUDMUX_PORT2_SSI1>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_TFSEL(MX51_AUDMUX_PORT4) |
@@ -220,7 +222,7 @@
 		>;
 	};
 
-	audmux_adu4 {
+	mux-aud4 {
 		fsl,audmux-port = <MX51_AUDMUX_PORT4>;
 		fsl,port-config = <
 			IMX_AUDMUX_V2_PTCR_SYN
@@ -254,12 +256,13 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi4>;
 	cs-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>,
-		   <&gpio3 29 GPIO_ACTIVE_LOW>;
+		   <&gpio3 29 GPIO_ACTIVE_LOW>,
+		   <&gpio3 25 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
 	/* default boot source: workaround #1 for errata ERR006282 */
-	smarc_flash: spi-flash@0 {
-		compatible = "winbond,w25q16dw", "jedec,spi-nor";
+	smarc_flash: flash@0 {
+		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <20000000>;
 	};
@@ -269,8 +272,24 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii";
-	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+	phy-connection-type = "rgmii-id";
+	phy-handle = <&ethphy>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <1000>;
+		};
+	};
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c2>;
 };
 
 &i2c_intern {
@@ -350,10 +369,6 @@
 				regulator-always-on;
 			};
 
-			/*
-			 * Per schematics, of all VGEN's, only VGEN5 has some
-			 * usage ... but even that - over DNI resistor
-			 */
 			vgen1 {
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <1550000>;
@@ -374,8 +389,7 @@
 				regulator-max-microvolt = <3300000>;
 			};
 
-			reg_2p5v_s0: vgen5 {
-				regulator-name = "V_2V5_S0";
+			vgen5 {
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3300000>;
 			};
@@ -397,7 +411,7 @@
 
 /* HDMI_CTRL */
 &i2c2 {
-	clock-frequency = <375000>;
+	clock-frequency = <100000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c2>;
 };
@@ -458,6 +472,8 @@
 			MX6QDL_PAD_EIM_D24__GPIO3_IO24 0x1b0b0
 			/* SPI_IMX_CS0# - connected to SMARC SPI0_CS0# */
 			MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1b0b0
+			/* SPI4_CS3# - connected to SMARC SPI0_CS1# */
+			MX6QDL_PAD_EIM_D25__GPIO3_IO25 0x1b0b0
 		>;
 	};
 
@@ -510,7 +526,7 @@
 			MX6QDL_PAD_ENET_MDIO__ENET_MDIO       0x1b0b0
 			MX6QDL_PAD_ENET_MDC__ENET_MDC         0x1b0b0
 			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK  0x1b0b0
-			MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25    0x1b0b0 /* RST_GBE0_PHY# */
+			MX6QDL_PAD_NANDF_D1__GPIO2_IO01       0x1b0b0 /* RST_GBE0_PHY# */
 		>;
 	};
 
@@ -636,6 +652,12 @@
 		>;
 	};
 
+	pinctrl_reg_sdio: reg-sdiogrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x1b0b0 /* SDIO_PWR_EN */
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
@@ -688,7 +710,6 @@
 
 			MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x1b0b0 /* CD */
 			MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b0b0 /* WP */
-			MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x1b0b0 /* PWR_EN */
 		>;
 	};
 
@@ -707,7 +728,7 @@
 		>;
 	};
 
-	pinctrl_wdog1: wdog1rp {
+	pinctrl_wdog1: wdog1grp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_9__WDOG1_B	0x1b0b0
 		>;
@@ -722,8 +743,7 @@
 &pcie {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pcie>;
-	wake-up-gpio = <&gpio6 18 GPIO_ACTIVE_HIGH>;
-	reset-gpio = <&gpio3 13 GPIO_ACTIVE_HIGH>;
+	reset-gpio = <&gpio3 13 GPIO_ACTIVE_LOW>;
 };
 
 /* LCD_BKLT_PWM */
@@ -791,12 +811,12 @@
 	pinctrl-0 = <&pinctrl_usdhc3>;
 	cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
 	wp-gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&reg_sdio>;
 	no-1-8-v;
 };
 
 /* SDMMC */
 &usdhc4 {
-	/* Internal eMMC, optional on some boards */
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc4>;
 	bus-width = <8>;
@@ -805,11 +825,13 @@
 	non-removable;
 	vmmc-supply = <&reg_3p3v_s0>;
 	vqmmc-supply = <&reg_1p8v_s0>;
+	status = "okay";
 };
 
 &wdog1 {
 	/* CPLD is feeded by watchdog (hardwired) */
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_wdog1>;
+	fsl,ext-reset-output;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx6qdl-mba6.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-mba6.dtsi
index f4dca20669d6..ee2c6bec92e8 100644
--- a/arch/arm/boot/dts/imx6qdl-mba6.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-mba6.dtsi
@@ -36,21 +36,21 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpiobuttons>;
 
-		button1 {
+		button-1 {
 			label = "s6";
 			linux,code = <KEY_F6>;
 			gpios = <&gpio7 13 GPIO_ACTIVE_LOW>;
 			wakeup-source;
 		};
 
-		button2 {
+		button-2 {
 			label = "s7";
 			linux,code = <KEY_F7>;
 			gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
 			wakeup-source;
 		};
 
-		button3 {
+		button-3 {
 			label = "s8";
 			linux,code = <KEY_F8>;
 			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
@@ -106,11 +106,25 @@
 		vin-supply = <&reg_mba6_3p3v>;
 	};
 
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		linux,cma {
+			compatible = "shared-dma-pool";
+			reusable;
+			size = <0x14000000>;
+			alloc-ranges = <0x10000000 0x20000000>;
+			linux,cma-default;
+		};
+	};
+
 	sound {
 		compatible = "fsl,imx-audio-tlv320aic32x4";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_audmux>;
-		model = "imx-audio-tlv320aic32x4";
+		model = "tqm-tlv320aic32";
 		ssi-controller = <&ssi1>;
 		audio-codec = <&tlv320aic32x4>;
 		audio-asrc = <&asrc>;
@@ -129,7 +143,7 @@
 &audmux {
 	status = "okay";
 
-	ssi0 {
+	mux-ssi0 {
 		fsl,audmux-port = <MX31_AUDMUX_PORT1_SSI0>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_SYN |
@@ -141,7 +155,7 @@
 		>;
 	};
 
-	aud3 {
+	mux-aud3 {
 		fsl,audmux-port = <MX31_AUDMUX_PORT3_SSI_PINS_3>;
 		fsl,port-config = <
 			IMX_AUDMUX_V2_PTCR_SYN
@@ -192,6 +206,13 @@
 	};
 };
 
+&hdmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hdmi>;
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
 &i2c1 {
 	tlv320aic32x4: audio-codec@18 {
 		compatible = "ti,tlv320aic32x4";
@@ -205,10 +226,22 @@
 	};
 };
 
+/* DDC */
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_recovery>;
+	scl-gpios = <&gpio4 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio4 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
 &pcie {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pcie>;
 	reset-gpio = <&gpio6 7 GPIO_ACTIVE_LOW>;
+	vpcie-supply = <&reg_pcie>;
 	status = "okay";
 };
 
@@ -244,7 +277,6 @@
 	status = "okay";
 };
 
-
 &uart3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart3>;
@@ -272,6 +304,23 @@
 &usbh1 {
 	disable-over-current;
 	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	hub@1 {
+		compatible = "usb424,2517";
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		vdd-supply = <&reg_mba6_3p3v>;
+
+		ethernet@1 {
+			compatible = "usb424,9e00";
+			reg = <1>;
+			nvmem-cells = <&mba_mac_address>;
+			nvmem-cell-names = "mac-address";
+		};
+	};
 };
 
 &usbotg {
@@ -396,10 +445,17 @@
 		>;
 	};
 
-	pinctrl_hog: hoggrp {
+	pinctrl_hdmi: hdmigrp {
+		/* NOTE: DDC is done via I2C2, so DON'T
+		 * configure DDC pins for HDMI!
+		 */
 		fsl,pins = <
-			MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x0001b099
+			MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1f8b0
+		>;
+	};
 
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
 			MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x0001b099
 			MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x0001b099
 			MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x0001b099
@@ -432,6 +488,20 @@
 		>;
 	};
 
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b899
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b899
+		>;
+	};
+
+	pinctrl_i2c2_recovery: i2c2recoverygrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x4001b899
+			MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x4001b899
+		>;
+	};
+
 	pinctrl_pcie: pciegrp {
 		fsl,pins = <
 			/* HYS = 1, DSE = 110, 100k up, SPEED = HIGH (11)*/
@@ -443,21 +513,21 @@
 
 	pinctrl_pwm1: pwm1grp {
 		fsl,pins = <
-			/* 100 k PD, DSE 120 OHM, SPPEED LO */
+			/* 100 k PD, DSE 120 OHM, SPEED LO */
 			MX6QDL_PAD_GPIO_9__PWM1_OUT 0x00003050
 		>;
 	};
 
 	pinctrl_pwm3: pwm3grp {
 		fsl,pins = <
-			/* 100 k PD, DSE 120 OHM, SPPEED LO */
+			/* 100 k PD, DSE 120 OHM, SPEED LO */
 			MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x00003050
 		>;
 	};
 
 	pinctrl_pwm4: pwm4grp {
 		fsl,pins = <
-			/* 100 k PD, DSE 120 OHM, SPPEED LO */
+			/* 100 k PD, DSE 120 OHM, SPEED LO */
 			MX6QDL_PAD_SD4_DAT2__PWM4_OUT 0x00003050
 		>;
 	};
diff --git a/arch/arm/boot/dts/imx6qdl-mba6a.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-mba6a.dtsi
index df8fa169e9f6..aca320ee8f47 100644
--- a/arch/arm/boot/dts/imx6qdl-mba6a.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-mba6a.dtsi
@@ -13,14 +13,26 @@
 
 &i2c1 {
 	lm75: temperature-sensor@49 {
-		compatible = "national,lm75";
+		compatible = "national,lm75a";
 		reg = <0x49>;
+		vs-supply = <&reg_mba6_3p3v>;
 	};
 
 	m24c64_57: eeprom@57 {
 		compatible = "atmel,24c64";
 		reg = <0x57>;
 		pagesize = <32>;
+		vcc-supply = <&reg_mba6_3p3v>;
+
+		nvmem-layout {
+			compatible = "fixed-layout";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			mba_mac_address: mac-address@20 {
+				reg = <0x20 0x6>;
+			};
+		};
 	};
 
 	rtc0: rtc@68 {
diff --git a/arch/arm/boot/dts/imx6qdl-mba6b.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-mba6b.dtsi
index 7d1cd7454c7f..c7bbd6195fef 100644
--- a/arch/arm/boot/dts/imx6qdl-mba6b.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-mba6b.dtsi
@@ -23,14 +23,26 @@
 
 &i2c3 {
 	lm75: temperature-sensor@49 {
-		compatible = "national,lm75";
+		compatible = "national,lm75a";
 		reg = <0x49>;
+		vs-supply = <&reg_mba6_3p3v>;
 	};
 
 	m24c64_57: eeprom@57 {
 		compatible = "atmel,24c64";
 		reg = <0x57>;
 		pagesize = <32>;
+		vcc-supply = <&reg_mba6_3p3v>;
+
+		nvmem-layout {
+			compatible = "fixed-layout";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			mba_mac_address: mac-address@20 {
+				reg = <0x20 0x6>;
+			};
+		};
 	};
 
 	rtc0: rtc@68 {
@@ -38,12 +50,3 @@
 		reg = <0x68>;
 	};
 };
-
-&iomuxc {
-	pinctrl_i2c1: i2c1grp {
-		fsl,pins = <
-			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b899
-			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b899
-		>;
-	};
-};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-nit6xlite.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-nit6xlite.dtsi
new file mode 100644
index 000000000000..8d471450d5c5
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-nit6xlite.dtsi
@@ -0,0 +1,570 @@
+// SPDX-License-Identifier: GPL-2.0 OR X11
+/*
+ * Copyright 2015 Boundary Devices, Inc.
+ */
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x20000000>;
+	};
+
+	reg_2p5v: regulator-2p5v {
+		compatible = "regulator-fixed";
+		regulator-name = "2P5V";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_wlan_vmmc: regulator-wlan-vmmc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wlan_vmmc>;
+		regulator-name = "reg_wlan_vmmc";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <70000>;
+		enable-active-high;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		key-home {
+			label = "Home";
+			gpios = <&gpio7 13 IRQ_TYPE_LEVEL_LOW>;
+			linux,code = <102>;
+		};
+
+		key-back {
+			label = "Back";
+			gpios = <&gpio4 5 IRQ_TYPE_LEVEL_LOW>;
+			linux,code = <158>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+
+		led-j14-pin1 {
+			gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+			retain-state-suspended;
+			default-state = "off";
+		};
+
+		led-j14-pin3 {
+			gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+			retain-state-suspended;
+			default-state = "off";
+		};
+
+		led-j14-pins8-9 {
+			gpios = <&gpio3 29 GPIO_ACTIVE_LOW>;
+			retain-state-suspended;
+			default-state = "off";
+		};
+
+		led-j46-pin2 {
+			gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
+			retain-state-suspended;
+			default-state = "off";
+		};
+
+		led-j46-pin3 {
+			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+			retain-state-suspended;
+			default-state = "off";
+		};
+	};
+
+	backlight-lcd {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <7>;
+		power-supply = <&reg_3p3v>;
+		status = "okay";
+	};
+
+	backlight_lvds0: backlight-lvds0 {
+		compatible = "pwm-backlight";
+		pwms = <&pwm4 0 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <7>;
+		power-supply = <&reg_3p3v>;
+		status = "okay";
+	};
+
+	panel-lvds0 {
+		compatible = "hannstar,hsd100pxn1";
+		backlight = <&backlight_lvds0>;
+
+		port {
+			panel_in_lvds0: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+
+	sound {
+		compatible = "fsl,imx6dl-nit6xlite-sgtl5000",
+			     "fsl,imx-audio-sgtl5000";
+		model = "imx6dl-nit6xlite-sgtl5000";
+		ssi-controller = <&ssi1>;
+		audio-codec = <&codec>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"Headphone Jack", "HP_OUT";
+		mux-int-port = <1>;
+		mux-ext-port = <3>;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+};
+
+&clks {
+	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+			  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
+				 <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash: flash@0 {
+		compatible = "microchip,sst25vf016b";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy>;
+	phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+	/delete-property/ interrupts;
+	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
+			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
+	fsl,err006687-workaround-present;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			txen-skew-ps = <0>;
+			txc-skew-ps = <3000>;
+			rxdv-skew-ps = <0>;
+			rxc-skew-ps = <3000>;
+			rxd0-skew-ps = <0>;
+			rxd1-skew-ps = <0>;
+			rxd2-skew-ps = <0>;
+			rxd3-skew-ps = <0>;
+			txd0-skew-ps = <0>;
+			txd1-skew-ps = <0>;
+			txd2-skew-ps = <0>;
+			txd3-skew-ps = <0>;
+		};
+	};
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	codec: sgtl5000@a {
+		compatible = "fsl,sgtl5000";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sgtl5000>;
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		clocks = <&clks IMX6QDL_CLK_CKO>;
+		VDDA-supply = <&reg_2p5v>;
+		VDDIO-supply = <&reg_3p3v>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	touchscreen@4 {
+		compatible = "eeti,egalax_ts";
+		reg = <0x04>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+		wakeup-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+	};
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5x06";
+		reg = <0x38>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+		wakeup-source;
+	};
+
+	rtc@6f {
+		compatible = "isil,isl1208";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc>;
+		reg = <0x6f>;
+		interrupts-extended = <&gpio2 26 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_j10>;
+	pinctrl-1 = <&pinctrl_j28>;
+
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
+			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
+			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
+			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19		0x000b1
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x100b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x100b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x100b0
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x100b0
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x100b0
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x100b0
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x100b0
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x100b0
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x100b0
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
+			/* Phy reset */
+			MX6QDL_PAD_ENET_RXD0__GPIO1_IO27	0x0f0b0
+			MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28	0x1b0b0
+			MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
+		>;
+	};
+
+	pinctrl_gpio_keys: gpio-keysgrp {
+		fsl,pins = <
+			/* Home Button: J14 pin 5 */
+			MX6QDL_PAD_GPIO_18__GPIO7_IO13		0x1b0b0
+			/* Back Button: J14 pin 7 */
+			MX6QDL_PAD_GPIO_19__GPIO4_IO05		0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__I2C1_SCL	0x4001b8b1
+			MX6QDL_PAD_EIM_D28__I2C1_SDA	0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL	0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA	0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL	0x4001b8b1
+			MX6QDL_PAD_GPIO_16__I2C3_SDA	0x4001b8b1
+			/* Touch IRQ: J7 pin 4 */
+			MX6QDL_PAD_GPIO_9__GPIO1_IO09	0x1b0b0
+			/* tcs2004 IRQ */
+			MX6QDL_PAD_EIM_LBA__GPIO2_IO27	0x1b0b0
+			/* tsc2004 reset */
+			MX6QDL_PAD_KEY_COL2__GPIO4_IO10	0x0b0b0
+		>;
+	};
+
+	pinctrl_j10: j10grp {
+		fsl,pins = <
+			/* Broadcom WiFi module pins */
+			MX6QDL_PAD_NANDF_D0__GPIO2_IO00		0x1b0b0
+			MX6QDL_PAD_NANDF_D1__GPIO2_IO01		0x1b0b0
+			MX6QDL_PAD_NANDF_D3__GPIO2_IO03		0x1b0b0
+			MX6QDL_PAD_NANDF_D4__GPIO2_IO04		0x1b0b0
+			MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09	0x0b0b0
+			MX6QDL_PAD_NANDF_CS1__GPIO6_IO14	0x1b0b0
+			MX6QDL_PAD_SD1_CLK__OSC32K_32K_OUT	0x000b0
+		>;
+	};
+
+	pinctrl_j28: j28grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1b0b0
+		>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x0b0b0
+			MX6QDL_PAD_GPIO_3__GPIO1_IO03		0x0b0b0
+			MX6QDL_PAD_EIM_D29__GPIO3_IO29		0x030b0
+			MX6QDL_PAD_GPIO_7__GPIO1_IO07		0x0b0b0
+			MX6QDL_PAD_GPIO_8__GPIO1_IO08		0x0b0b0
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT3__PWM1_OUT		0x1b0b1
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT1__PWM3_OUT		0x1b0b1
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__PWM4_OUT		0x1b0b1
+		>;
+	};
+
+	pinctrl_wlan_vmmc: wlan-vmmcgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CLE__GPIO6_IO07	0x030b0
+		>;
+	};
+
+	pinctrl_rtc: rtcgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_RW__GPIO2_IO26		0x1b0b0
+		>;
+	};
+
+	pinctrl_sgtl5000: sgtl5000grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_0__CCM_CLKO1		0x000b0
+			MX6QDL_PAD_EIM_A25__GPIO5_IO02		0x1b0b0
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
+			MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D26__UART2_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D27__UART2_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D23__UART3_CTS_B		0x1b0b1
+			MX6QDL_PAD_EIM_D31__UART3_RTS_B		0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
+			MX6QDL_PAD_KEY_COL4__USB_OTG_OC		0x1b0b0
+			/* power enable, high active */
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x000b0
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+			MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x1b0b0
+		>;
+	};
+};
+
+&ldb {
+	status = "okay";
+
+	lvds-channel@0 {
+		status = "okay";
+
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in_lvds0>;
+			};
+		};
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+	status = "okay";
+};
+
+&ssi1 {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	bus-width = <4>;
+	non-removable;
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_wlan_vmmc>;
+	cap-power-off-card;
+	keep-power-in-suspend;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6_max.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6_max.dtsi
new file mode 100644
index 000000000000..c727aac257f9
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6_max.dtsi
@@ -0,0 +1,832 @@
+// SPDX-License-Identifier: GPL-2.0 OR X11
+/*
+ * Copyright 2015 Boundary Devices, Inc.
+ */
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0xF0000000>;
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	reg_2p5v: regulator-2p5v {
+		compatible = "regulator-fixed";
+		regulator-name = "2P5V";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh1>;
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_wlan_vmmc: regulator-wlan-vmmc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wlan_vmmc>;
+		regulator-name = "reg_wlan_vmmc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio6 15 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <70000>;
+		enable-active-high;
+	};
+
+	reg_can_xcvr: regulator-can-xcvr {
+		compatible = "regulator-fixed";
+		regulator-name = "CAN XCVR";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can_xcvr>;
+		gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		key-power {
+			label = "Power Button";
+			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+
+		key-menu {
+			label = "Menu";
+			gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_MENU>;
+		};
+
+		key-home {
+			label = "Home";
+			gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOME>;
+		};
+
+		key-back {
+			label = "Back";
+			gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_BACK>;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio7 13 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio7 1 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+	};
+
+	i2c-mux-2 {
+		compatible = "i2c-mux-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_i2c2mux>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		mux-gpios = <&gpio3 20 GPIO_ACTIVE_HIGH
+			     &gpio4 15 GPIO_ACTIVE_HIGH>;
+		i2c-parent = <&i2c2>;
+		idle-state = <0>;
+
+		i2c2mux@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c2mux@2 {
+			reg = <2>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	i2c-mux-3 {
+		compatible = "i2c-mux-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_i2c3mux>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		mux-gpios = <&gpio2 25 GPIO_ACTIVE_HIGH>;
+		i2c-parent = <&i2c3>;
+		idle-state = <0>;
+
+		i2c3mux@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-speaker-enable {
+			gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+			retain-state-suspended;
+			default-state = "off";
+		};
+
+		led-ttymxc4-rs232 {
+			gpios = <&gpio6 10 GPIO_ACTIVE_HIGH>;
+			retain-state-suspended;
+			default-state = "on";
+		};
+	};
+
+	backlight_lcd: backlight-lcd {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <7>;
+		power-supply = <&reg_3p3v>;
+		status = "okay";
+	};
+
+	backlight_lvds0: backlight-lvds0 {
+		compatible = "pwm-backlight";
+		pwms = <&pwm4 0 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <7>;
+		power-supply = <&reg_3p3v>;
+		status = "okay";
+	};
+
+	backlight_lvds1: backlight-lvds1 {
+		compatible = "pwm-backlight";
+		pwms = <&pwm2 0 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <7>;
+		power-supply = <&reg_3p3v>;
+		status = "okay";
+	};
+
+	lcd_display: disp0 {
+		compatible = "fsl,imx-parallel-display";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interface-pix-fmt = "bgr666";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_j15>;
+		status = "okay";
+
+		port@0 {
+			reg = <0>;
+
+			lcd_display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			lcd_display_out: endpoint {
+				remote-endpoint = <&lcd_panel_in>;
+			};
+		};
+	};
+
+	panel-lcd {
+		compatible = "okaya,rs800480t-7x0gp";
+		backlight = <&backlight_lcd>;
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
+	};
+
+	panel-lvds0 {
+		compatible = "hannstar,hsd100pxn1";
+		backlight = <&backlight_lvds0>;
+
+		port {
+			panel_in_lvds0: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+
+	panel-lvds1 {
+		compatible = "hannstar,hsd100pxn1";
+		backlight = <&backlight_lvds1>;
+
+		port {
+			panel_in_lvds1: endpoint {
+				remote-endpoint = <&lvds1_out>;
+			};
+		};
+	};
+
+	sound {
+		compatible = "fsl,imx6q-nitrogen6_max-sgtl5000",
+			     "fsl,imx-audio-sgtl5000";
+		model = "imx6q-nitrogen6_max-sgtl5000";
+		ssi-controller = <&ssi1>;
+		audio-codec = <&codec>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"Headphone Jack", "HP_OUT";
+		mux-int-port = <1>;
+		mux-ext-port = <3>;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	xceiver-supply = <&reg_can_xcvr>;
+	status = "okay";
+};
+
+&clks {
+	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+			  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
+				 <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash: flash@0 {
+		compatible = "microchip,sst25vf016b";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy>;
+	phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+	/delete-property/ interrupts;
+	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
+			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
+	fsl,err006687-workaround-present;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			txen-skew-ps = <0>;
+			txc-skew-ps = <3000>;
+			rxdv-skew-ps = <0>;
+			rxc-skew-ps = <3000>;
+			rxd0-skew-ps = <0>;
+			rxd1-skew-ps = <0>;
+			rxd2-skew-ps = <0>;
+			rxd3-skew-ps = <0>;
+			txd0-skew-ps = <0>;
+			txd1-skew-ps = <0>;
+			txd2-skew-ps = <0>;
+			txd3-skew-ps = <0>;
+		};
+	};
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	codec: sgtl5000@a {
+		compatible = "fsl,sgtl5000";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sgtl5000>;
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		clocks = <&clks IMX6QDL_CLK_CKO>;
+		VDDA-supply = <&reg_2p5v>;
+		VDDIO-supply = <&reg_3p3v>;
+	};
+
+	rtc: rtc@68 {
+		compatible = "microcrystal,rv4162";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rv4162>;
+		reg = <0x68>;
+		interrupts-extended = <&gpio4 6 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	touchscreen@4 {
+		compatible = "eeti,egalax_ts";
+		reg = <0x04>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+		wakeup-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+	};
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5x06";
+		reg = <0x38>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+		wakeup-source;
+	};
+};
+
+&iomuxc {
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
+			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
+			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
+			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
+		>;
+	};
+
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b0
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX	0x1b0b0
+		>;
+	};
+
+	pinctrl_can_xcvr: can-xcvrgrp {
+		fsl,pins = <
+			/* Flexcan XCVR enable */
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1b0b0
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19		0x000b1
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x100b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x100b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x10030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x10030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x10030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x10030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x10030
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x10030
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x100b0
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
+			/* Phy reset */
+			MX6QDL_PAD_ENET_RXD0__GPIO1_IO27	0x0f0b0
+			MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28	0x1b0b0
+			MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
+		>;
+	};
+
+	pinctrl_gpio_keys: gpio-keysgrp {
+		fsl,pins = <
+			/* Power Button */
+			MX6QDL_PAD_NANDF_D3__GPIO2_IO03		0x1b0b0
+			/* Menu Button */
+			MX6QDL_PAD_NANDF_D1__GPIO2_IO01		0x1b0b0
+			/* Home Button */
+			MX6QDL_PAD_NANDF_D4__GPIO2_IO04		0x1b0b0
+			/* Back Button */
+			MX6QDL_PAD_NANDF_D2__GPIO2_IO02		0x1b0b0
+			/* Volume Up Button */
+			MX6QDL_PAD_GPIO_18__GPIO7_IO13		0x1b0b0
+			/* Volume Down Button */
+			MX6QDL_PAD_SD3_DAT4__GPIO7_IO01		0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__I2C1_SCL	0x4001b8b1
+			MX6QDL_PAD_EIM_D28__I2C1_SDA	0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL	0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA	0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2mux: i2c2muxgrp {
+		fsl,pins = <
+			/* ov5642 camera i2c enable */
+			MX6QDL_PAD_EIM_D20__GPIO3_IO20	0x000b0
+			/* ov5640_mipi camera i2c enable */
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15	0x000b0
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL	0x4001b8b1
+			MX6QDL_PAD_GPIO_16__I2C3_SDA	0x4001b8b1
+			MX6QDL_PAD_GPIO_9__GPIO1_IO09	0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c3mux: i2c3muxgrp {
+		fsl,pins = <
+			/* PCIe I2C enable */
+			MX6QDL_PAD_EIM_OE__GPIO2_IO25	0x000b0
+		>;
+	};
+
+	pinctrl_j15: j15grp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
+			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15       0x10
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02        0x10
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03        0x10
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00   0x10
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01   0x10
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02   0x10
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03   0x10
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04   0x10
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05   0x10
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06   0x10
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07   0x10
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08   0x10
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09   0x10
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10  0x10
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11  0x10
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12  0x10
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13  0x10
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14  0x10
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15  0x10
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16  0x10
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17  0x10
+			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18  0x10
+			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19  0x10
+			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20  0x10
+			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21  0x10
+			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22  0x10
+			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23  0x10
+		>;
+	};
+
+	pinctrl_pcie: pciegrp {
+		fsl,pins = <
+			/* PCIe reset */
+			MX6QDL_PAD_EIM_BCLK__GPIO6_IO31	0x000b0
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT3__PWM1_OUT	0x1b0b1
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT2__PWM2_OUT	0x1b0b1
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT1__PWM3_OUT	0x1b0b1
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__PWM4_OUT	0x1b0b1
+		>;
+	};
+
+	pinctrl_rv4162: rv4162grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__GPIO4_IO06	0x1b0b0
+		>;
+	};
+
+	pinctrl_sgtl5000: sgtl5000grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_0__CCM_CLKO1		0x000b0
+			MX6QDL_PAD_EIM_A25__GPIO5_IO02		0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__GPIO1_IO29	0x1b0b0
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
+			MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D26__UART2_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D27__UART2_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA	0x130b1
+			MX6QDL_PAD_KEY_COL1__UART5_TX_DATA	0x030b1
+			/* RS485 RX Enable: pull up */
+			MX6QDL_PAD_NANDF_RB0__GPIO6_IO10	0x1b0b1
+			/* RS485 DEN: pull down */
+			MX6QDL_PAD_NANDF_CLE__GPIO6_IO07	0x030b1
+			/* RS485/!RS232 Select: pull down (rs232) */
+			MX6QDL_PAD_EIM_CS1__GPIO2_IO24		0x030b1
+			/* ON: pull down */
+			MX6QDL_PAD_NANDF_ALE__GPIO6_IO08	0x030b1
+		>;
+	};
+
+	pinctrl_usbh1: usbh1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12		0x0b0b0
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
+			MX6QDL_PAD_KEY_COL4__USB_OTG_OC		0x1b0b0
+			/* power enable, high active */
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x000b0
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+			MX6QDL_PAD_NANDF_CS1__SD3_VSELECT	0x100b0
+			MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
+			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059
+			MX6QDL_PAD_SD4_DAT4__SD4_DATA4		0x17059
+			MX6QDL_PAD_SD4_DAT5__SD4_DATA5		0x17059
+			MX6QDL_PAD_SD4_DAT6__SD4_DATA6		0x17059
+			MX6QDL_PAD_SD4_DAT7__SD4_DATA7		0x17059
+		>;
+	};
+
+	pinctrl_wlan_vmmc: wlan-vmmcgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CS0__GPIO6_IO11	0x100b0
+			MX6QDL_PAD_NANDF_CS2__GPIO6_IO15	0x000b0
+			MX6QDL_PAD_NANDF_CS3__GPIO6_IO16	0x000b0
+			MX6QDL_PAD_SD1_CLK__OSC32K_32K_OUT	0x000b0
+		>;
+	};
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&lcd_display_in>;
+};
+
+&ldb {
+	status = "okay";
+
+	lvds-channel@0 {
+		status = "okay";
+
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in_lvds0>;
+			};
+		};
+	};
+
+	lvds-channel@1 {
+		status = "okay";
+
+		port@4 {
+			reg = <4>;
+
+			lvds1_out: endpoint {
+				remote-endpoint = <&panel_in_lvds1>;
+			};
+		};
+	};
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	reset-gpio = <&gpio6 31 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "okay";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+	status = "okay";
+};
+
+&ssi1 {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usb_h1_vbus>;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	bus-width = <4>;
+	non-removable;
+	vmmc-supply = <&reg_wlan_vmmc>;
+	cap-power-off-card;
+	keep-power-in-suspend;
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1271";
+		reg = <2>;
+		interrupt-parent = <&gpio6>;
+		interrupts = <11 IRQ_TYPE_LEVEL_HIGH>;
+		ref-clock-frequency = <38400000>;
+	};
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+};
+
+&usdhc4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	bus-width = <8>;
+	non-removable;
+	vmmc-supply = <&reg_1p8v>;
+	keep-power-in-suspend;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-nitrogen6_som2.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6_som2.dtsi
index 92d09a3ebe0e..806af7f60419 100644
--- a/arch/arm/boot/dts/imx6qdl-nitrogen6_som2.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6_som2.dtsi
@@ -17,7 +17,7 @@
 
 	backlight_lcd: backlight-lcd {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 		power-supply = <&reg_3p3v>;
@@ -26,7 +26,7 @@
 
 	backlight_lvds0: backlight-lvds0 {
 		compatible = "pwm-backlight";
-		pwms = <&pwm4 0 5000000>;
+		pwms = <&pwm4 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 		power-supply = <&reg_3p3v>;
@@ -47,38 +47,38 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_keys>;
 
-		power {
+		key-power {
 			label = "Power Button";
 			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			wakeup-source;
 		};
 
-		menu {
+		key-menu {
 			label = "Menu";
 			gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_MENU>;
 		};
 
-		home {
+		key-home {
 			label = "Home";
 			gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_HOME>;
 		};
 
-		back {
+		key-back {
 			label = "Back";
 			gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_BACK>;
 		};
 
-		volume-up {
+		key-volume-up {
 			label = "Volume Up";
 			gpios = <&gpio7 13 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
 		};
 
-		volume-down {
+		key-volume-down {
 			label = "Volume Down";
 			gpios = <&gpio7 1 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
@@ -252,7 +252,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "microchip,sst25vf016b";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
@@ -263,6 +263,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
@@ -285,6 +286,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_sgtl5000>;
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_3p3v>;
@@ -639,7 +641,6 @@
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
@@ -652,7 +653,6 @@
 };
 
 &pwm4 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6x.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6x.dtsi
new file mode 100644
index 000000000000..c71aa7498acf
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-nitrogen6x.dtsi
@@ -0,0 +1,678 @@
+// SPDX-License-Identifier: GPL-2.0 OR X11
+/*
+ * Copyright 2013 Boundary Devices, Inc.
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ */
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x40000000>;
+	};
+
+	reg_2p5v: regulator-2p5v {
+		compatible = "regulator-fixed";
+		regulator-name = "2P5V";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 0>;
+		enable-active-high;
+	};
+
+	reg_can_xcvr: regulator-can-xcvr {
+		compatible = "regulator-fixed";
+		regulator-name = "CAN XCVR";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can_xcvr>;
+		gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
+	};
+
+	reg_wlan_vmmc: regulator-wlan-vmmc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wlan_vmmc>;
+		regulator-name = "reg_wlan_vmmc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio6 15 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <70000>;
+		enable-active-high;
+	};
+
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh1>;
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		key-power {
+			label = "Power Button";
+			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+
+		key-menu {
+			label = "Menu";
+			gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_MENU>;
+		};
+
+		key-home {
+			label = "Home";
+			gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOME>;
+		};
+
+		key-back {
+			label = "Back";
+			gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_BACK>;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio7 13 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio4 5 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+	};
+
+	sound {
+		compatible = "fsl,imx6q-nitrogen6x-sgtl5000",
+			     "fsl,imx-audio-sgtl5000";
+		model = "imx6q-nitrogen6x-sgtl5000";
+		ssi-controller = <&ssi1>;
+		audio-codec = <&codec>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"Headphone Jack", "HP_OUT";
+		mux-int-port = <1>;
+		mux-ext-port = <3>;
+	};
+
+	backlight_lcd: backlight-lcd {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <7>;
+		power-supply = <&reg_3p3v>;
+		status = "okay";
+	};
+
+	backlight_lvds: backlight-lvds {
+		compatible = "pwm-backlight";
+		pwms = <&pwm4 0 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <7>;
+		power-supply = <&reg_3p3v>;
+		status = "okay";
+	};
+
+	lcd_display: disp0 {
+		compatible = "fsl,imx-parallel-display";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interface-pix-fmt = "bgr666";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_j15>;
+		status = "okay";
+
+		port@0 {
+			reg = <0>;
+
+			lcd_display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			lcd_display_out: endpoint {
+				remote-endpoint = <&lcd_panel_in>;
+			};
+		};
+	};
+
+	panel-lcd {
+		compatible = "okaya,rs800480t-7x0gp";
+		backlight = <&backlight_lcd>;
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
+	};
+
+	panel-lvds0 {
+		compatible = "hannstar,hsd100pxn1";
+		backlight = <&backlight_lvds>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	xceiver-supply = <&reg_can_xcvr>;
+	status = "okay";
+};
+
+&clks {
+	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+			  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
+				 <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash: flash@0 {
+		compatible = "sst,sst25vf016b", "jedec,spi-nor";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "bootloader";
+			reg = <0x0 0xc0000>;
+		};
+
+		partition@c0000 {
+			label = "env";
+			reg = <0xc0000 0x2000>;
+		};
+
+		partition@c2000 {
+			label = "splash";
+			reg = <0xc2000 0x13e000>;
+		};
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy>;
+	phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+	/delete-property/ interrupts;
+	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
+			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
+	fsl,err006687-workaround-present;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			txen-skew-ps = <0>;
+			txc-skew-ps = <3000>;
+			rxdv-skew-ps = <0>;
+			rxc-skew-ps = <3000>;
+			rxd0-skew-ps = <0>;
+			rxd1-skew-ps = <0>;
+			rxd2-skew-ps = <0>;
+			rxd3-skew-ps = <0>;
+			txd0-skew-ps = <0>;
+			txd1-skew-ps = <0>;
+			txd2-skew-ps = <0>;
+			txd3-skew-ps = <0>;
+		};
+	};
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	codec: sgtl5000@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		clocks = <&clks IMX6QDL_CLK_CKO>;
+		VDDA-supply = <&reg_2p5v>;
+		VDDIO-supply = <&reg_3p3v>;
+	};
+
+	rtc: rtc@6f {
+		compatible = "isil,isl1208";
+		reg = <0x6f>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	touchscreen@4 {
+		compatible = "eeti,egalax_ts";
+		reg = <0x04>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+		wakeup-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+	};
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5x06";
+		reg = <0x38>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+		wakeup-source;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			/* SGTL5000 sys_mclk */
+			MX6QDL_PAD_GPIO_0__CCM_CLKO1    0x030b0
+			MX6QDL_PAD_GPIO_9__GPIO1_IO09	0x1b0b0
+		>;
+	};
+
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
+			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
+			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
+			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
+		>;
+	};
+
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b0
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX	0x1b0b0
+		>;
+	};
+
+	pinctrl_can_xcvr: can-xcvrgrp {
+		fsl,pins = <
+			/* Flexcan XCVR enable */
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1b0b0
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19  0x000b1	/* CS */
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x100b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x100b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x10030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x10030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x10030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x10030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x10030
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x10030
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x100b0
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
+			/* Phy reset */
+			MX6QDL_PAD_ENET_RXD0__GPIO1_IO27	0x000b0
+			MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
+		>;
+	};
+
+	pinctrl_gpio_keys: gpio-keysgrp {
+		fsl,pins = <
+			/* Power Button */
+			MX6QDL_PAD_NANDF_D3__GPIO2_IO03		0x1b0b0
+			/* Menu Button */
+			MX6QDL_PAD_NANDF_D1__GPIO2_IO01		0x1b0b0
+			/* Home Button */
+			MX6QDL_PAD_NANDF_D4__GPIO2_IO04		0x1b0b0
+			/* Back Button */
+			MX6QDL_PAD_NANDF_D2__GPIO2_IO02		0x1b0b0
+			/* Volume Up Button */
+			MX6QDL_PAD_GPIO_18__GPIO7_IO13		0x1b0b0
+			/* Volume Down Button */
+			MX6QDL_PAD_GPIO_19__GPIO4_IO05		0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
+			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL		0x4001b8b1
+			MX6QDL_PAD_GPIO_16__I2C3_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_j15: j15grp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
+			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15       0x10
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02        0x10
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03        0x10
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00   0x10
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01   0x10
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02   0x10
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03   0x10
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04   0x10
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05   0x10
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06   0x10
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07   0x10
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08   0x10
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09   0x10
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10  0x10
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11  0x10
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12  0x10
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13  0x10
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14  0x10
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15  0x10
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16  0x10
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17  0x10
+			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18  0x10
+			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19  0x10
+			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20  0x10
+			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21  0x10
+			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22  0x10
+			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23  0x10
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT1__PWM3_OUT 0x1b0b1
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
+			MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D26__UART2_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D27__UART2_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbh1: usbh1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12		0x030b0
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID	0x17059
+			MX6QDL_PAD_KEY_COL4__USB_OTG_OC	0x1b0b0
+			/* power enable, high active */
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22  0x000b0
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17071
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10071
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17071
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17071
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17071
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17071
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+			MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0	/* CD */
+		>;
+	};
+
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
+			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059
+			MX6QDL_PAD_NANDF_D6__GPIO2_IO06 0x1b0b0	/* CD */
+		>;
+	};
+
+	pinctrl_wlan_vmmc: wlan-vmmcgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CS0__GPIO6_IO11	0x100b0
+			MX6QDL_PAD_NANDF_CS2__GPIO6_IO15	0x000b0
+			MX6QDL_PAD_NANDF_CS3__GPIO6_IO16	0x000b0
+			MX6QDL_PAD_SD1_CLK__OSC32K_32K_OUT	0x000b0
+		>;
+	};
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&lcd_display_in>;
+};
+
+&ldb {
+	status = "okay";
+
+	lvds-channel@0 {
+		status = "okay";
+
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+	status = "okay";
+};
+
+&ssi1 {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usb_h1_vbus>;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	bus-width = <4>;
+	non-removable;
+	vmmc-supply = <&reg_wlan_vmmc>;
+	cap-power-off-card;
+	keep-power-in-suspend;
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1271";
+		reg = <2>;
+		interrupt-parent = <&gpio6>;
+		interrupts = <14 IRQ_TYPE_LEVEL_HIGH>;
+		ref-clock-frequency = <38400000>;
+	};
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+};
+
+&usdhc4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	cd-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-phytec-mira-peb-av-02.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-mira-peb-av-02.dtsi
index 393475cb0f4d..0020dbb1722c 100644
--- a/arch/arm/boot/dts/imx6qdl-phytec-mira-peb-av-02.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-mira-peb-av-02.dtsi
@@ -64,7 +64,7 @@
 		interrupt-parent = <&gpio3>;
 		interrupts = <2 IRQ_TYPE_NONE>;
 		status = "disabled";
-        };
+	};
 };
 
 &ipu1_di0_disp0 {
diff --git a/arch/arm/boot/dts/imx6qdl-phytec-mira-peb-eval-01.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-mira-peb-eval-01.dtsi
index 037b60197598..fc78acc9f5c5 100644
--- a/arch/arm/boot/dts/imx6qdl-phytec-mira-peb-eval-01.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-mira-peb-eval-01.dtsi
@@ -13,14 +13,14 @@
 		pinctrl-0 = <&pinctrl_gpio_keys>;
 		status = "disabled";
 
-		power {
+		key-power {
 			label = "Power Button";
 			gpios = <&gpio5 28 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_WAKEUP>;
 			wakeup-source;
 		};
 
-		sleep {
+		key-sleep {
 			label = "Sleep Button";
 			gpios = <&gpio6 18 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_SLEEP>;
@@ -35,19 +35,19 @@
 
 		user-led1 {
 			gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "gpio";
+			linux,default-trigger = "none";
 			default-state = "on";
 		};
 
 		user-led2 {
 			gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "gpio";
+			linux,default-trigger = "none";
 			default-state = "on";
 		};
 
 		user-led3 {
 			gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "gpio";
+			linux,default-trigger = "none";
 			default-state = "on";
 		};
 	};
diff --git a/arch/arm/boot/dts/imx6qdl-phytec-mira-peb-wlbt-05.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-mira-peb-wlbt-05.dtsi
index 84f884d6e55b..08b2dd06580a 100644
--- a/arch/arm/boot/dts/imx6qdl-phytec-mira-peb-wlbt-05.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-mira-peb-wlbt-05.dtsi
@@ -54,7 +54,7 @@
 };
 
 &iomuxc {
-	pinctrl_uart3_bt: uart3grp-bt {
+	pinctrl_uart3_bt: uart3-btgrp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
 			MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
@@ -66,7 +66,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_wl: usdhc3grp-wl {
+	pinctrl_usdhc3_wl: usdhc3-wlgrp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
 			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
diff --git a/arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-mira.dtsi
index 120d6e997a4c..a3c2811e9c6f 100644
--- a/arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-mira.dtsi
@@ -15,7 +15,7 @@
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 		power-supply = <&reg_backlight>;
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		status = "okay";
 	};
 
@@ -25,17 +25,17 @@
 		pinctrl-0 = <&pinctrl_gpioleds>;
 		status = "disabled";
 
-		red {
+		led-red {
 			label = "phyboard-mira:red";
 			gpios = <&gpio5 22 GPIO_ACTIVE_HIGH>;
 		};
 
-		green {
+		led-green {
 			label = "phyboard-mira:green";
 			gpios = <&gpio5 23 GPIO_ACTIVE_HIGH>;
 		};
 
-		blue {
+		led-blue {
 			label = "phyboard-mira:blue";
 			gpios = <&gpio5 24 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "mmc0";
@@ -162,7 +162,7 @@
 		interrupts = <12 IRQ_TYPE_NONE>;
 		status = "disabled";
 
-		stmpe_touchscreen {
+		touchscreen {
 			compatible = "st,stmpe-ts";
 			st,sample-time = <4>;
 			st,mod-12b = <1>;
@@ -182,7 +182,7 @@
 		pinctrl-0 = <&pinctrl_rtc_int>;
 		reg = <0x68>;
 		interrupt-parent = <&gpio7>;
-		interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
 		status = "disabled";
 	};
 };
@@ -224,7 +224,6 @@
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6qdl-phytec-pbab01.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-pbab01.dtsi
index 51d28e275aa6..e40041871b28 100644
--- a/arch/arm/boot/dts/imx6qdl-phytec-pbab01.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-pbab01.dtsi
@@ -10,22 +10,18 @@
 		stdout-path = &uart4;
 	};
 
-	regulators {
-		sound_1v8: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "i2s-audio-1v8";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
+	sound_1v8: regulator-sound-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "i2s-audio-1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
 
-		sound_3v3: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "i2s-audio-3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-		};
+	sound_3v3: regulator-sound-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "i2s-audio-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
 	};
 
 	tlv320_mclk: oscillator {
@@ -75,7 +71,7 @@
 &audmux {
 	status = "okay";
 
-	ssi2 {
+	mux-ssi2 {
 		fsl,audmux-port = <1>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_SYN |
@@ -87,7 +83,7 @@
 		>;
 	};
 
-	pins5 {
+	mux-pins5 {
 		fsl,audmux-port = <4>;
 		fsl,port-config = <
 			IMX_AUDMUX_V2_PTCR_SYN
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-pfla02.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-pfla02.dtsi
new file mode 100644
index 000000000000..aa9a442852f4
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-pfla02.dtsi
@@ -0,0 +1,465 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Christian Hemp, Phytec Messtechnik GmbH
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Phytec phyFLEX-i.MX6 Quad";
+	compatible = "phytec,imx6q-pfla02", "fsl,imx6q";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x80000000>;
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio4 15 0>;
+		enable-active-high;
+	};
+
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh1_vbus>;
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 0 0>;
+		enable-active-high;
+	};
+
+	gpio_leds: leds {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+		compatible = "gpio-leds";
+
+		led_green: led-green {
+			label = "phyflex:green";
+			gpios = <&gpio1 30 0>;
+		};
+
+		led_red: led-red {
+			label = "phyflex:red";
+			gpios = <&gpio2 31 0>;
+		};
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "disabled";
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	status = "disabled";
+};
+
+&ecspi3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3>;
+	status = "okay";
+	cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
+
+	som_flash: flash@0 {
+		compatible = "m25p80", "jedec,spi-nor";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-handle = <&ethphy>;
+	phy-mode = "rgmii";
+	phy-reset-duration = <10>; /* in msecs */
+	phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
+	phy-supply = <&vdd_eth_io_reg>;
+	status = "disabled";
+
+	fec_mdio: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			txc-skew-ps = <1680>;
+			rxc-skew-ps = <1860>;
+		};
+	};
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	nand-on-flash-bbt;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	som_eeprom: eeprom@50 {
+		compatible = "catalyst,24c32", "atmel,24c32";
+		pagesize = <32>;
+		reg = <0x50>;
+	};
+
+	pmic@58 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		compatible = "dlg,da9063";
+		reg = <0x58>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <9 IRQ_TYPE_LEVEL_LOW>; /* active-low GPIO2_9 */
+		#interrupt-cells = <2>;
+		interrupt-controller;
+
+		regulators {
+			vddcore_reg: bcore1 {
+				regulator-min-microvolt = <730000>;
+				regulator-max-microvolt = <1380000>;
+				regulator-always-on;
+			};
+
+			vddsoc_reg: bcore2 {
+				regulator-min-microvolt = <730000>;
+				regulator-max-microvolt = <1380000>;
+				regulator-always-on;
+			};
+
+			vdd_ddr3_reg: bpro {
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+			};
+
+			vdd_3v3_reg: bperi {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vdd_buckmem_reg: bmem {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vdd_eth_reg: bio {
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+			};
+
+			vdd_eth_io_reg: ldo4 {
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
+				regulator-always-on;
+			};
+
+			vdd_mx6_snvs_reg: ldo5 {
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-always-on;
+			};
+
+			vdd_3v3_pmic_io_reg: ldo6 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vdd_sd0_reg: ldo9 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vdd_sd1_reg: ldo10 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vdd_mx6_high_reg: ldo11 {
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-always-on;
+			};
+		};
+
+		da9063_rtc: rtc {
+			compatible = "dlg,da9063-rtc";
+		};
+
+		da9063_wdog: watchdog {
+			compatible = "dlg,da9063-watchdog";
+		};
+
+		onkey {
+			compatible = "dlg,da9063-onkey";
+			status = "disabled";
+		};
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	clock-frequency = <100000>;
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	clock-frequency = <100000>;
+};
+
+&iomuxc {
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO	0x100b1
+			MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI	0x100b1
+			MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK	0x100b1
+			MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24	0x80000000 /* CS0 */
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN	0x1b0b0
+			MX6QDL_PAD_EIM_D23__GPIO3_IO23		0x80000000 /* Reset GPIO */
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX	0x1b0b0
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b0
+		>;
+	};
+
+	pinctrl_gpmi_nand: gpminandgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CLE__NAND_CLE		0xb0b1
+			MX6QDL_PAD_NANDF_ALE__NAND_ALE		0xb0b1
+			MX6QDL_PAD_NANDF_WP_B__NAND_WP_B	0xb0b1
+			MX6QDL_PAD_NANDF_RB0__NAND_READY_B	0xb000
+			MX6QDL_PAD_NANDF_CS0__NAND_CE0_B	0xb0b1
+			MX6QDL_PAD_NANDF_CS1__NAND_CE1_B	0xb0b1
+			MX6QDL_PAD_SD4_CMD__NAND_RE_B		0xb0b1
+			MX6QDL_PAD_SD4_CLK__NAND_WE_B		0xb0b1
+			MX6QDL_PAD_NANDF_D0__NAND_DATA00	0xb0b1
+			MX6QDL_PAD_NANDF_D1__NAND_DATA01	0xb0b1
+			MX6QDL_PAD_NANDF_D2__NAND_DATA02	0xb0b1
+			MX6QDL_PAD_NANDF_D3__NAND_DATA03	0xb0b1
+			MX6QDL_PAD_NANDF_D4__NAND_DATA04	0xb0b1
+			MX6QDL_PAD_NANDF_D5__NAND_DATA05	0xb0b1
+			MX6QDL_PAD_NANDF_D6__NAND_DATA06	0xb0b1
+			MX6QDL_PAD_NANDF_D7__NAND_DATA07	0xb0b1
+			MX6QDL_PAD_SD4_DAT0__NAND_DQS		0x00b1
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
+			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_EB2__I2C2_SCL		0x4001b8b1
+			MX6QDL_PAD_EIM_D16__I2C2_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__I2C3_SCL		0x4001b8b1
+			MX6QDL_PAD_EIM_D18__I2C3_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_TXD0__GPIO1_IO30	0x80000000 /* Green LED */
+			MX6QDL_PAD_EIM_EB3__GPIO2_IO31		0x80000000 /* Red LED */
+		>;
+	};
+
+	pinctrl_pcie: pciegrp {
+		fsl,pins = <MX6QDL_PAD_DI0_PIN15__GPIO4_IO17  0x80000000>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <MX6QDL_PAD_SD4_DAT1__GPIO2_IO09	0x80000000>; /* PMIC interrupt */
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D31__UART3_RTS_B		0x1b0b1
+			MX6QDL_PAD_EIM_D30__UART3_CTS_B		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA	0x1b0b1
+			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbh1_vbus: usbh1vbusgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_0__GPIO1_IO00		0x1b0b0
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
+			MX6QDL_PAD_KEY_COL4__USB_OTG_OC		0x1b0b0
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x80000000
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+		>;
+	};
+
+	pinctrl_usdhc3_cdwp: usdhc3cdwpgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x80000000
+			MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x80000000
+		>;
+	};
+
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT16__AUD5_TXC	0x130b0
+			MX6QDL_PAD_DISP0_DAT17__AUD5_TXD	0x110b0
+			MX6QDL_PAD_DISP0_DAT18__AUD5_TXFS	0x130b0
+			MX6QDL_PAD_DISP0_DAT19__AUD5_RXD	0x130b0
+		>;
+	};
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	reset-gpio = <&gpio4 17 GPIO_ACTIVE_LOW>;
+	status = "disabled";
+};
+
+&reg_arm {
+	vin-supply = <&vddcore_reg>;
+};
+
+&reg_pu {
+	vin-supply = <&vddsoc_reg>;
+};
+
+&reg_soc {
+	vin-supply = <&vddsoc_reg>;
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	uart-has-rtscts;
+	status = "disabled";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "disabled";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usb_h1_vbus>;
+	status = "disabled";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	disable-over-current;
+	status = "disabled";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&vdd_sd1_reg>;
+	status = "disabled";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3
+		     &pinctrl_usdhc3_cdwp>;
+	cd-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&vdd_sd0_reg>;
+	status = "disabled";
+};
+
+&wdog1 {
+	/*
+	 * Rely on PMIC reboot handler. Internal i.MX6 watchdog, that is also
+	 * used for reboot, does not reset all external PMIC voltages on reset.
+	 */
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-phycore-som.dtsi
index 28a805384668..85e278eb2016 100644
--- a/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-phytec-phycore-som.dtsi
@@ -100,6 +100,7 @@
 		interrupt-parent = <&gpio1>;
 		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
+		#interrupt-cells = <2>;
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -309,3 +310,11 @@
 		>;
 	};
 };
+
+&wdog1 {
+	/*
+	 * Rely on PMIC reboot handler. Internal i.MX6 watchdog, that is also
+	 * used for reboot, does not reset all external PMIC voltages on reset.
+	 */
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-pico-dwarf.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-pico-dwarf.dtsi
index 3a968782e854..3a968782e854 100644
--- a/arch/arm/boot/dts/imx6qdl-pico-dwarf.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-pico-dwarf.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-pico-hobbit.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-pico-hobbit.dtsi
index 144c4727fbc7..144c4727fbc7 100644
--- a/arch/arm/boot/dts/imx6qdl-pico-hobbit.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-pico-hobbit.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-pico-nymph.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-pico-nymph.dtsi
index 3d56a4216448..3d56a4216448 100644
--- a/arch/arm/boot/dts/imx6qdl-pico-nymph.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-pico-nymph.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-pico-pi.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-pico-pi.dtsi
index b823dce62e63..b823dce62e63 100644
--- a/arch/arm/boot/dts/imx6qdl-pico-pi.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-pico-pi.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-pico.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-pico.dtsi
index f7a56d6b160c..c39a9ebdaba1 100644
--- a/arch/arm/boot/dts/imx6qdl-pico.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-pico.dtsi
@@ -233,7 +233,6 @@
 		pinctrl-0 = <&pinctrl_ov5645>;
 		reg = <0x3c>;
 		clocks = <&clks IMX6QDL_CLK_CKO2>;
-		clock-names = "xclk";
 		clock-frequency = <24000000>;
 		vdddo-supply = <&reg_1p8v>;
 		vdda-supply = <&reg_2p8v>;
diff --git a/arch/arm/boot/dts/imx6qdl-prti6q.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-prti6q.dtsi
index 19578f660b09..36f84f4da6b0 100644
--- a/arch/arm/boot/dts/imx6qdl-prti6q.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-prti6q.dtsi
@@ -69,6 +69,7 @@
 	vbus-supply = <&reg_usb_h1_vbus>;
 	phy_type = "utmi";
 	dr_mode = "host";
+	disable-over-current;
 	status = "okay";
 };
 
@@ -78,10 +79,18 @@
 	pinctrl-0 = <&pinctrl_usbotg>;
 	phy_type = "utmi";
 	dr_mode = "host";
-	disable-over-current;
+	over-current-active-low;
 	status = "okay";
 };
 
+&usbphynop1 {
+	status = "disabled";
+};
+
+&usbphynop2 {
+	status = "disabled";
+};
+
 &usdhc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc1>;
@@ -94,6 +103,9 @@
 	pinctrl-0 = <&pinctrl_usdhc3>;
 	bus-width = <8>;
 	non-removable;
+	no-1-8-v;
+	no-sd;
+	no-sdio;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-rex.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-rex.dtsi
new file mode 100644
index 000000000000..22d5918ee4d8
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-rex.dtsi
@@ -0,0 +1,355 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2014 FEDEVEL, Inc.
+ *
+ * Author: Robert Nelson <robertcnelson@gmail.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_usbh1_vbus: regulator-usbh1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usbh1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usb_otg_vbus: regulator-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_led>;
+
+		led0: led-usr {
+			label = "usr";
+			gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	sound {
+		compatible = "fsl,imx6-rex-sgtl5000",
+			     "fsl,imx-audio-sgtl5000";
+		model = "imx6-rex-sgtl5000";
+		ssi-controller = <&ssi1>;
+		audio-codec = <&codec>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"Headphone Jack", "HP_OUT";
+		mux-int-port = <1>;
+		mux-ext-port = <3>;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+};
+
+&ecspi2 {
+	cs-gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	status = "okay";
+};
+
+&ecspi3 {
+	cs-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3>;
+	status = "okay";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii";
+	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	codec: sgtl5000@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		clocks = <&clks IMX6QDL_CLK_CKO>;
+		VDDA-supply = <&reg_3p3v>;
+		VDDIO-supply = <&reg_3p3v>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	pca9535: gpio-expander@27 {
+		compatible = "nxp,pca9535";
+		reg = <0x27>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pca9535>;
+		interrupt-parent = <&gpio6>;
+		interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	eeprom@57 {
+		compatible = "atmel,24c02";
+		reg = <0x57>;
+	};
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			/* SGTL5000 sys_mclk */
+			MX6QDL_PAD_GPIO_0__CCM_CLKO1		0x030b0
+		>;
+	};
+
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
+			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
+			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
+			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO	0x100b1
+			MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI	0x100b1
+			MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK	0x100b1
+			/* CS */
+			MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26	0x000b1
+		>;
+	};
+
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT17__ECSPI2_MISO	0x100b1
+			MX6QDL_PAD_DISP0_DAT16__ECSPI2_MOSI	0x100b1
+			MX6QDL_PAD_DISP0_DAT19__ECSPI2_SCLK	0x100b1
+			/* CS */
+			MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12	0x000b1
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
+			/* Phy reset */
+			MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25	0x000b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA		0x4001b8b1
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__I2C3_SCL		0x4001b8b1
+			MX6QDL_PAD_EIM_D18__I2C3_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_led: ledgrp {
+		fsl,pins = <
+			/* user led */
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x80000000
+		>;
+	};
+
+	pinctrl_pca9535: pca9535grp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CS3__GPIO6_IO16	0x17059
+	   >;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA	0x1b0b1
+			MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbh1: usbh1grp {
+		fsl,pins = <
+			/* power enable, high active */
+			MX6QDL_PAD_EIM_D31__GPIO3_IO31		0x10b0
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
+			MX6QDL_PAD_EIM_D21__USB_OTG_OC		0x1b0b0
+			/* power enable, high active */
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x10b0
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+			/* CD */
+			MX6QDL_PAD_NANDF_D2__GPIO2_IO02		0x1b0b0
+			/* WP */
+			MX6QDL_PAD_NANDF_D3__GPIO2_IO03		0x1f0b0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+			/* CD */
+			MX6QDL_PAD_NANDF_D0__GPIO2_IO00		0x1b0b0
+			/* WP */
+			MX6QDL_PAD_NANDF_D1__GPIO2_IO01		0x1f0b0
+		>;
+	};
+};
+
+&ssi1 {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usbh1_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbh1>;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	bus-width = <4>;
+	cd-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	bus-width = <4>;
+	cd-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-sabreauto.dtsi
index 5e58740d40c5..b9dde0af3b99 100644
--- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-sabreauto.dtsi
@@ -21,7 +21,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		user {
+		led-user {
 			label = "debug";
 			gpios = <&gpio5 15 GPIO_ACTIVE_HIGH>;
 		};
@@ -32,35 +32,35 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_keys>;
 
-		home {
+		key-home {
 			label = "Home";
 			gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_HOME>;
 			wakeup-source;
 		};
 
-		back {
+		key-back {
 			label = "Back";
 			gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_BACK>;
 			wakeup-source;
 		};
 
-		program {
+		key-program {
 			label = "Program";
 			gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_PROGRAM>;
 			wakeup-source;
 		};
 
-		volume-up {
+		key-volume-up {
 			label = "Volume Up";
 			gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
 			wakeup-source;
 		};
 
-		volume-down {
+		key-volume-down {
 			label = "Volume Down";
 			gpios = <&gpio5 14 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
@@ -143,17 +143,22 @@
 			"AIN2R", "Line In Jack";
 	};
 
+	spdif_in: spdif-in {
+		compatible = "linux,spdif-dir";
+		#sound-dai-cells = <0>;
+	};
+
 	sound-spdif {
-		compatible = "fsl,imx-audio-spdif",
-			   "fsl,imx-sabreauto-spdif";
+		compatible = "fsl,imx-sabreauto-spdif",
+			     "fsl,imx-audio-spdif";
 		model = "imx-spdif";
-		spdif-controller = <&spdif>;
-		spdif-in;
+		audio-cpu = <&spdif>;
+		audio-codec = <&spdif_in>;
 	};
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm3 0 5000000>;
+		pwms = <&pwm3 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 		status = "okay";
@@ -272,7 +277,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1_cs>;
 	status = "disabled"; /* pin conflict with WEIM NOR */
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p32", "jedec,spi-nor";
@@ -295,6 +300,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii-id";
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
@@ -335,7 +341,7 @@
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
 		reg = <0x08>;
 
@@ -451,8 +457,8 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_egalax_int>;
 		interrupt-parent = <&gpio2>;
-		interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
-		wakeup-gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>;
+		interrupts = <28 IRQ_TYPE_LEVEL_LOW>;
+		wakeup-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
 	};
 };
 
@@ -466,312 +472,310 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hog>;
 
-	imx6qdl-sabreauto {
-		pinctrl_hog: hoggrp {
-			fsl,pins = <
-				MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x80000000
-				MX6QDL_PAD_SD2_DAT2__GPIO1_IO13  0x80000000
-				MX6QDL_PAD_GPIO_18__SD3_VSELECT 0x17059
-			>;
-		};
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x80000000
+			MX6QDL_PAD_SD2_DAT2__GPIO1_IO13  0x80000000
+			MX6QDL_PAD_GPIO_18__SD3_VSELECT 0x17059
+		>;
+	};
 
-		pinctrl_ecspi1: ecspi1grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
-				MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
-				MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
-			>;
-		};
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
+		>;
+	};
 
-		pinctrl_ecspi1_cs: ecspi1cs {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x80000000
-			>;
-		};
+	pinctrl_ecspi1_cs: ecspi1csgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x80000000
+		>;
+	};
 
-		pinctrl_egalax_int: egalax-intgrp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_EB0__GPIO2_IO28		0xb0b1
-			>;
-		};
+	pinctrl_egalax_int: egalax-intgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_EB0__GPIO2_IO28		0xb0b1
+		>;
+	};
 
-		pinctrl_enet: enetgrp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL1__ENET_MDIO		0x1b0b0
-				MX6QDL_PAD_KEY_COL2__ENET_MDC		0x1b0b0
-				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
-				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
-				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
-				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
-				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
-				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
-				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
-				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
-				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
-				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
-				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
-				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
-				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
-				MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
-			>;
-		};
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL1__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_KEY_COL2__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
+			MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
+		>;
+	};
 
-		pinctrl_esai: esaigrp {
-			fsl,pins = <
-				MX6QDL_PAD_ENET_CRS_DV__ESAI_TX_CLK 0x1b030
-				MX6QDL_PAD_ENET_RXD1__ESAI_TX_FS    0x1b030
-				MX6QDL_PAD_ENET_TX_EN__ESAI_TX3_RX2 0x1b030
-				MX6QDL_PAD_GPIO_5__ESAI_TX2_RX3     0x1b030
-				MX6QDL_PAD_ENET_TXD0__ESAI_TX4_RX1  0x1b030
-				MX6QDL_PAD_ENET_MDC__ESAI_TX5_RX0   0x1b030
-				MX6QDL_PAD_GPIO_17__ESAI_TX0        0x1b030
-				MX6QDL_PAD_NANDF_CS3__ESAI_TX1      0x1b030
-				MX6QDL_PAD_ENET_MDIO__ESAI_RX_CLK   0x1b030
-				MX6QDL_PAD_GPIO_9__ESAI_RX_FS       0x1b030
-			>;
-		};
+	pinctrl_esai: esaigrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_CRS_DV__ESAI_TX_CLK 0x1b030
+			MX6QDL_PAD_ENET_RXD1__ESAI_TX_FS    0x1b030
+			MX6QDL_PAD_ENET_TX_EN__ESAI_TX3_RX2 0x1b030
+			MX6QDL_PAD_GPIO_5__ESAI_TX2_RX3     0x1b030
+			MX6QDL_PAD_ENET_TXD0__ESAI_TX4_RX1  0x1b030
+			MX6QDL_PAD_ENET_MDC__ESAI_TX5_RX0   0x1b030
+			MX6QDL_PAD_GPIO_17__ESAI_TX0        0x1b030
+			MX6QDL_PAD_NANDF_CS3__ESAI_TX1      0x1b030
+			MX6QDL_PAD_ENET_MDIO__ESAI_RX_CLK   0x1b030
+			MX6QDL_PAD_GPIO_9__ESAI_RX_FS       0x1b030
+		>;
+	};
 
-		pinctrl_flexcan1: flexcan1grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX        0x17059
-				MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x17059
-			>;
-		};
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX        0x17059
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x17059
+		>;
+	};
 
-		pinctrl_flexcan2: flexcan2grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX	0x17059
-				MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX	0x17059
-			>;
-		};
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX	0x17059
+			MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX	0x17059
+		>;
+	};
 
-		pinctrl_gpio_keys: gpiokeysgrp {
-			fsl,pins = <
-				MX6QDL_PAD_SD2_CMD__GPIO1_IO11		0x1b0b0
-				MX6QDL_PAD_SD2_DAT3__GPIO1_IO12		0x1b0b0
-				MX6QDL_PAD_SD4_DAT4__GPIO2_IO12		0x1b0b0
-				MX6QDL_PAD_SD4_DAT7__GPIO2_IO15		0x1b0b0
-				MX6QDL_PAD_DISP0_DAT20__GPIO5_IO14	0x1b0b0
-			>;
-		};
+	pinctrl_gpio_keys: gpiokeysgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__GPIO1_IO11		0x1b0b0
+			MX6QDL_PAD_SD2_DAT3__GPIO1_IO12		0x1b0b0
+			MX6QDL_PAD_SD4_DAT4__GPIO2_IO12		0x1b0b0
+			MX6QDL_PAD_SD4_DAT7__GPIO2_IO15		0x1b0b0
+			MX6QDL_PAD_DISP0_DAT20__GPIO5_IO14	0x1b0b0
+		>;
+	};
 
-		pinctrl_gpio_leds: gpioledsgrp {
-			fsl,pins = <
-				MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15	0x80000000
-			>;
-		};
+	pinctrl_gpio_leds: gpioledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15	0x80000000
+		>;
+	};
 
-		pinctrl_gpmi_nand: gpminandgrp {
-			fsl,pins = <
-				MX6QDL_PAD_NANDF_CLE__NAND_CLE		0xb0b1
-				MX6QDL_PAD_NANDF_ALE__NAND_ALE		0xb0b1
-				MX6QDL_PAD_NANDF_WP_B__NAND_WP_B	0xb0b1
-				MX6QDL_PAD_NANDF_RB0__NAND_READY_B	0xb000
-				MX6QDL_PAD_NANDF_CS0__NAND_CE0_B	0xb0b1
-				MX6QDL_PAD_NANDF_CS1__NAND_CE1_B	0xb0b1
-				MX6QDL_PAD_SD4_CMD__NAND_RE_B		0xb0b1
-				MX6QDL_PAD_SD4_CLK__NAND_WE_B		0xb0b1
-				MX6QDL_PAD_NANDF_D0__NAND_DATA00	0xb0b1
-				MX6QDL_PAD_NANDF_D1__NAND_DATA01	0xb0b1
-				MX6QDL_PAD_NANDF_D2__NAND_DATA02	0xb0b1
-				MX6QDL_PAD_NANDF_D3__NAND_DATA03	0xb0b1
-				MX6QDL_PAD_NANDF_D4__NAND_DATA04	0xb0b1
-				MX6QDL_PAD_NANDF_D5__NAND_DATA05	0xb0b1
-				MX6QDL_PAD_NANDF_D6__NAND_DATA06	0xb0b1
-				MX6QDL_PAD_NANDF_D7__NAND_DATA07	0xb0b1
-				MX6QDL_PAD_SD4_DAT0__NAND_DQS		0x00b1
-			>;
-		};
+	pinctrl_gpmi_nand: gpminandgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CLE__NAND_CLE		0xb0b1
+			MX6QDL_PAD_NANDF_ALE__NAND_ALE		0xb0b1
+			MX6QDL_PAD_NANDF_WP_B__NAND_WP_B	0xb0b1
+			MX6QDL_PAD_NANDF_RB0__NAND_READY_B	0xb000
+			MX6QDL_PAD_NANDF_CS0__NAND_CE0_B	0xb0b1
+			MX6QDL_PAD_NANDF_CS1__NAND_CE1_B	0xb0b1
+			MX6QDL_PAD_SD4_CMD__NAND_RE_B		0xb0b1
+			MX6QDL_PAD_SD4_CLK__NAND_WE_B		0xb0b1
+			MX6QDL_PAD_NANDF_D0__NAND_DATA00	0xb0b1
+			MX6QDL_PAD_NANDF_D1__NAND_DATA01	0xb0b1
+			MX6QDL_PAD_NANDF_D2__NAND_DATA02	0xb0b1
+			MX6QDL_PAD_NANDF_D3__NAND_DATA03	0xb0b1
+			MX6QDL_PAD_NANDF_D4__NAND_DATA04	0xb0b1
+			MX6QDL_PAD_NANDF_D5__NAND_DATA05	0xb0b1
+			MX6QDL_PAD_NANDF_D6__NAND_DATA06	0xb0b1
+			MX6QDL_PAD_NANDF_D7__NAND_DATA07	0xb0b1
+			MX6QDL_PAD_SD4_DAT0__NAND_DQS		0x00b1
+		>;
+	};
 
-		pinctrl_hdmi_cec: hdmicecgrp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE	0x1f8b0
-			>;
-		};
+	pinctrl_hdmi_cec: hdmicecgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE	0x1f8b0
+		>;
+	};
 
-		pinctrl_i2c2: i2c2grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_EB2__I2C2_SCL	0x4001b8b1
-				MX6QDL_PAD_KEY_ROW3__I2C2_SDA	0x4001b8b1
-			>;
-		};
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_EB2__I2C2_SCL	0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA	0x4001b8b1
+		>;
+	};
 
-		pinctrl_i2c3: i2c3grp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_3__I2C3_SCL  0x4001b8b1
-				MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
-			>;
-		};
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_3__I2C3_SCL  0x4001b8b1
+			MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
+		>;
+	};
 
-		pinctrl_i2c3mux: i2c3muxgrp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x0b0b1
-			>;
-		};
+	pinctrl_i2c3mux: i2c3muxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x0b0b1
+		>;
+	};
 
-		pinctrl_ipu1_csi0: ipu1csi0grp {
-			fsl,pins = <
-				MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12  0x1b0b0
-				MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13  0x1b0b0
-				MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14  0x1b0b0
-				MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15  0x1b0b0
-				MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16  0x1b0b0
-				MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17  0x1b0b0
-				MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18  0x1b0b0
-				MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19  0x1b0b0
-				MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
-				MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC    0x1b0b0
-				MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC   0x1b0b0
-			>;
-		};
+	pinctrl_ipu1_csi0: ipu1csi0grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12  0x1b0b0
+			MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13  0x1b0b0
+			MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14  0x1b0b0
+			MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15  0x1b0b0
+			MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16  0x1b0b0
+			MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17  0x1b0b0
+			MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18  0x1b0b0
+			MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19  0x1b0b0
+			MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
+			MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC    0x1b0b0
+			MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC   0x1b0b0
+		>;
+	};
 
-		pinctrl_max7310: max7310grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD2_DAT0__GPIO1_IO15 0x1b0b0
-			>;
-		};
+	pinctrl_max7310: max7310grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_DAT0__GPIO1_IO15 0x1b0b0
+		>;
+	};
 
-		pinctrl_mma8451_int: mma8451intgrp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_BCLK__GPIO6_IO31		0xb0b1
-			>;
-		};
+	pinctrl_mma8451_int: mma8451intgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_BCLK__GPIO6_IO31		0xb0b1
+		>;
+	};
 
-		pinctrl_pwm3: pwm1grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
-			>;
-		};
+	pinctrl_pwm3: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT1__PWM3_OUT		0x1b0b1
+		>;
+	};
 
-		pinctrl_gpt_input_capture0: gptinputcapture0grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_DAT0__GPT_CAPTURE1	0x1b0b0
-			>;
-		};
+	pinctrl_gpt_input_capture0: gptinputcapture0grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT0__GPT_CAPTURE1	0x1b0b0
+		>;
+	};
 
-		pinctrl_gpt_input_capture1: gptinputcapture1grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_DAT1__GPT_CAPTURE2	0x1b0b0
-			>;
-		};
+	pinctrl_gpt_input_capture1: gptinputcapture1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT1__GPT_CAPTURE2	0x1b0b0
+		>;
+	};
 
-		pinctrl_spdif: spdifgrp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL3__SPDIF_IN 0x1b0b0
-			>;
-		};
+	pinctrl_spdif: spdifgrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__SPDIF_IN 0x1b0b0
+		>;
+	};
 
-		pinctrl_uart4: uart4grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL0__UART4_TX_DATA	0x1b0b1
-				MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA	0x1b0b1
-			>;
-		};
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA	0x1b0b1
+			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA	0x1b0b1
+		>;
+	};
 
-		pinctrl_usbotg: usbotggrp {
-			fsl,pins = <
-				MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
-			>;
-		};
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
+		>;
+	};
 
-		pinctrl_usdhc3: usdhc3grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
-				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
-				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
-				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
-				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
-				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
-				MX6QDL_PAD_SD3_DAT4__SD3_DATA4		0x17059
-				MX6QDL_PAD_SD3_DAT5__SD3_DATA5		0x17059
-				MX6QDL_PAD_SD3_DAT6__SD3_DATA6		0x17059
-				MX6QDL_PAD_SD3_DAT7__SD3_DATA7		0x17059
-			>;
-		};
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4		0x17059
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5		0x17059
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6		0x17059
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7		0x17059
+		>;
+	};
 
-		pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170b9
-				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100b9
-				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x170b9
-				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x170b9
-				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x170b9
-				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x170b9
-				MX6QDL_PAD_SD3_DAT4__SD3_DATA4		0x170b9
-				MX6QDL_PAD_SD3_DAT5__SD3_DATA5		0x170b9
-				MX6QDL_PAD_SD3_DAT6__SD3_DATA6		0x170b9
-				MX6QDL_PAD_SD3_DAT7__SD3_DATA7		0x170b9
-			>;
-		};
+	pinctrl_usdhc3_100mhz: usdhc3-100mhz-grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170b9
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100b9
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x170b9
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x170b9
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x170b9
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x170b9
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4		0x170b9
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5		0x170b9
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6		0x170b9
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7		0x170b9
+		>;
+	};
 
-		pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170f9
-				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100f9
-				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x170f9
-				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x170f9
-				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x170f9
-				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x170f9
-				MX6QDL_PAD_SD3_DAT4__SD3_DATA4		0x170f9
-				MX6QDL_PAD_SD3_DAT5__SD3_DATA5		0x170f9
-				MX6QDL_PAD_SD3_DAT6__SD3_DATA6		0x170f9
-				MX6QDL_PAD_SD3_DAT7__SD3_DATA7		0x170f9
-			>;
-		};
+	pinctrl_usdhc3_200mhz: usdhc3-200mhz-grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x170f9
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x100f9
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x170f9
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x170f9
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x170f9
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x170f9
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4		0x170f9
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5		0x170f9
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6		0x170f9
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7		0x170f9
+		>;
+	};
 
-		pinctrl_weim_cs0: weimcs0grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_CS0__EIM_CS0_B		0xb0b1
-			>;
-		};
+	pinctrl_weim_cs0: weimcs0grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_CS0__EIM_CS0_B		0xb0b1
+		>;
+	};
 
-		pinctrl_weim_nor: weimnorgrp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_OE__EIM_OE_B		0xb0b1
-				MX6QDL_PAD_EIM_RW__EIM_RW		0xb0b1
-				MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B		0xb060
-				MX6QDL_PAD_EIM_D16__EIM_DATA16		0x1b0b0
-				MX6QDL_PAD_EIM_D17__EIM_DATA17		0x1b0b0
-				MX6QDL_PAD_EIM_D18__EIM_DATA18		0x1b0b0
-				MX6QDL_PAD_EIM_D19__EIM_DATA19		0x1b0b0
-				MX6QDL_PAD_EIM_D20__EIM_DATA20		0x1b0b0
-				MX6QDL_PAD_EIM_D21__EIM_DATA21		0x1b0b0
-				MX6QDL_PAD_EIM_D22__EIM_DATA22		0x1b0b0
-				MX6QDL_PAD_EIM_D23__EIM_DATA23		0x1b0b0
-				MX6QDL_PAD_EIM_D24__EIM_DATA24		0x1b0b0
-				MX6QDL_PAD_EIM_D25__EIM_DATA25		0x1b0b0
-				MX6QDL_PAD_EIM_D26__EIM_DATA26		0x1b0b0
-				MX6QDL_PAD_EIM_D27__EIM_DATA27		0x1b0b0
-				MX6QDL_PAD_EIM_D28__EIM_DATA28		0x1b0b0
-				MX6QDL_PAD_EIM_D29__EIM_DATA29		0x1b0b0
-				MX6QDL_PAD_EIM_D30__EIM_DATA30		0x1b0b0
-				MX6QDL_PAD_EIM_D31__EIM_DATA31		0x1b0b0
-				MX6QDL_PAD_EIM_A23__EIM_ADDR23		0xb0b1
-				MX6QDL_PAD_EIM_A22__EIM_ADDR22		0xb0b1
-				MX6QDL_PAD_EIM_A21__EIM_ADDR21		0xb0b1
-				MX6QDL_PAD_EIM_A20__EIM_ADDR20		0xb0b1
-				MX6QDL_PAD_EIM_A19__EIM_ADDR19		0xb0b1
-				MX6QDL_PAD_EIM_A18__EIM_ADDR18		0xb0b1
-				MX6QDL_PAD_EIM_A17__EIM_ADDR17		0xb0b1
-				MX6QDL_PAD_EIM_A16__EIM_ADDR16		0xb0b1
-				MX6QDL_PAD_EIM_DA15__EIM_AD15		0xb0b1
-				MX6QDL_PAD_EIM_DA14__EIM_AD14		0xb0b1
-				MX6QDL_PAD_EIM_DA13__EIM_AD13		0xb0b1
-				MX6QDL_PAD_EIM_DA12__EIM_AD12		0xb0b1
-				MX6QDL_PAD_EIM_DA11__EIM_AD11		0xb0b1
-				MX6QDL_PAD_EIM_DA10__EIM_AD10		0xb0b1
-				MX6QDL_PAD_EIM_DA9__EIM_AD09		0xb0b1
-				MX6QDL_PAD_EIM_DA8__EIM_AD08		0xb0b1
-				MX6QDL_PAD_EIM_DA7__EIM_AD07		0xb0b1
-				MX6QDL_PAD_EIM_DA6__EIM_AD06		0xb0b1
-				MX6QDL_PAD_EIM_DA5__EIM_AD05		0xb0b1
-				MX6QDL_PAD_EIM_DA4__EIM_AD04		0xb0b1
-				MX6QDL_PAD_EIM_DA3__EIM_AD03		0xb0b1
-				MX6QDL_PAD_EIM_DA2__EIM_AD02		0xb0b1
-				MX6QDL_PAD_EIM_DA1__EIM_AD01		0xb0b1
-				MX6QDL_PAD_EIM_DA0__EIM_AD00		0xb0b1
-			>;
-		};
+	pinctrl_weim_nor: weimnorgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_OE__EIM_OE_B		0xb0b1
+			MX6QDL_PAD_EIM_RW__EIM_RW		0xb0b1
+			MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B		0xb060
+			MX6QDL_PAD_EIM_D16__EIM_DATA16		0x1b0b0
+			MX6QDL_PAD_EIM_D17__EIM_DATA17		0x1b0b0
+			MX6QDL_PAD_EIM_D18__EIM_DATA18		0x1b0b0
+			MX6QDL_PAD_EIM_D19__EIM_DATA19		0x1b0b0
+			MX6QDL_PAD_EIM_D20__EIM_DATA20		0x1b0b0
+			MX6QDL_PAD_EIM_D21__EIM_DATA21		0x1b0b0
+			MX6QDL_PAD_EIM_D22__EIM_DATA22		0x1b0b0
+			MX6QDL_PAD_EIM_D23__EIM_DATA23		0x1b0b0
+			MX6QDL_PAD_EIM_D24__EIM_DATA24		0x1b0b0
+			MX6QDL_PAD_EIM_D25__EIM_DATA25		0x1b0b0
+			MX6QDL_PAD_EIM_D26__EIM_DATA26		0x1b0b0
+			MX6QDL_PAD_EIM_D27__EIM_DATA27		0x1b0b0
+			MX6QDL_PAD_EIM_D28__EIM_DATA28		0x1b0b0
+			MX6QDL_PAD_EIM_D29__EIM_DATA29		0x1b0b0
+			MX6QDL_PAD_EIM_D30__EIM_DATA30		0x1b0b0
+			MX6QDL_PAD_EIM_D31__EIM_DATA31		0x1b0b0
+			MX6QDL_PAD_EIM_A23__EIM_ADDR23		0xb0b1
+			MX6QDL_PAD_EIM_A22__EIM_ADDR22		0xb0b1
+			MX6QDL_PAD_EIM_A21__EIM_ADDR21		0xb0b1
+			MX6QDL_PAD_EIM_A20__EIM_ADDR20		0xb0b1
+			MX6QDL_PAD_EIM_A19__EIM_ADDR19		0xb0b1
+			MX6QDL_PAD_EIM_A18__EIM_ADDR18		0xb0b1
+			MX6QDL_PAD_EIM_A17__EIM_ADDR17		0xb0b1
+			MX6QDL_PAD_EIM_A16__EIM_ADDR16		0xb0b1
+			MX6QDL_PAD_EIM_DA15__EIM_AD15		0xb0b1
+			MX6QDL_PAD_EIM_DA14__EIM_AD14		0xb0b1
+			MX6QDL_PAD_EIM_DA13__EIM_AD13		0xb0b1
+			MX6QDL_PAD_EIM_DA12__EIM_AD12		0xb0b1
+			MX6QDL_PAD_EIM_DA11__EIM_AD11		0xb0b1
+			MX6QDL_PAD_EIM_DA10__EIM_AD10		0xb0b1
+			MX6QDL_PAD_EIM_DA9__EIM_AD09		0xb0b1
+			MX6QDL_PAD_EIM_DA8__EIM_AD08		0xb0b1
+			MX6QDL_PAD_EIM_DA7__EIM_AD07		0xb0b1
+			MX6QDL_PAD_EIM_DA6__EIM_AD06		0xb0b1
+			MX6QDL_PAD_EIM_DA5__EIM_AD05		0xb0b1
+			MX6QDL_PAD_EIM_DA4__EIM_AD04		0xb0b1
+			MX6QDL_PAD_EIM_DA3__EIM_AD03		0xb0b1
+			MX6QDL_PAD_EIM_DA2__EIM_AD02		0xb0b1
+			MX6QDL_PAD_EIM_DA1__EIM_AD01		0xb0b1
+			MX6QDL_PAD_EIM_DA0__EIM_AD00		0xb0b1
+		>;
 	};
 };
 
@@ -785,7 +789,7 @@
 
 		display-timings {
 			native-mode = <&timing0>;
-			timing0: hsd100pxn1 {
+			timing0: timing-hsd100pxn1 {
 				clock-frequency = <65000000>;
 				hactive = <1024>;
 				vactive = <768>;
@@ -801,7 +805,6 @@
 };
 
 &pwm3 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "okay";
@@ -851,7 +854,7 @@
 	ranges = <0 0 0x08000000 0x08000000>;
 	status = "disabled"; /* pin conflict with SPI NOR */
 
-	nor@0,0 {
+	flash@0,0 {
 		compatible = "cfi-flash";
 		reg = <0 0 0x02000000>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-sabrelite.dtsi
new file mode 100644
index 000000000000..f7abc17c7c93
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-sabrelite.dtsi
@@ -0,0 +1,730 @@
+// SPDX-License-Identifier: GPL-2.0 OR X11
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ */
+
+#include <dt-bindings/clock/imx6qdl-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	aliases {
+		mmc0 = &usdhc3;
+		mmc1 = &usdhc4;
+	};
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x40000000>;
+	};
+
+	reg_2p5v: regulator-2p5v {
+		compatible = "regulator-fixed";
+		regulator-name = "2P5V";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 0>;
+		enable-active-high;
+	};
+
+	reg_can_xcvr: regulator-can-xcvr {
+		compatible = "regulator-fixed";
+		regulator-name = "CAN XCVR";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can_xcvr>;
+		gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
+	};
+
+	reg_1p5v: regulator-1p5v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P5V";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	reg_2p8v: regulator-2p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "2P8V";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		regulator-always-on;
+	};
+
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh1>;
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	mipi_xclk: mipi_xclk {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <22000000>;
+		clock-output-names = "mipi_pwm3";
+		pwms = <&pwm3 0 45 0>; /* 1 / 45 ns = 22 MHz */
+		status = "okay";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		key-power {
+			label = "Power Button";
+			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+
+		key-menu {
+			label = "Menu";
+			gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_MENU>;
+		};
+
+		key-home {
+			label = "Home";
+			gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOME>;
+		};
+
+		key-back {
+			label = "Back";
+			gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_BACK>;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio7 13 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio4 5 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+	};
+
+	sound {
+		compatible = "fsl,imx6q-sabrelite-sgtl5000",
+			     "fsl,imx-audio-sgtl5000";
+		model = "imx6q-sabrelite-sgtl5000";
+		ssi-controller = <&ssi1>;
+		audio-codec = <&codec>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"Headphone Jack", "HP_OUT";
+		mux-int-port = <1>;
+		mux-ext-port = <4>;
+	};
+
+	backlight_lcd: backlight-lcd {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <7>;
+		power-supply = <&reg_3p3v>;
+		status = "okay";
+	};
+
+	backlight_lvds: backlight-lvds {
+		compatible = "pwm-backlight";
+		pwms = <&pwm4 0 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <7>;
+		power-supply = <&reg_3p3v>;
+		status = "okay";
+	};
+
+	lcd_display: disp0 {
+		compatible = "fsl,imx-parallel-display";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interface-pix-fmt = "bgr666";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_j15>;
+		status = "okay";
+
+		port@0 {
+			reg = <0>;
+
+			lcd_display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			lcd_display_out: endpoint {
+				remote-endpoint = <&lcd_panel_in>;
+			};
+		};
+	};
+
+	panel-lcd {
+		compatible = "okaya,rs800480t-7x0gp";
+		backlight = <&backlight_lcd>;
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
+	};
+
+	panel-lvds0 {
+		compatible = "hannstar,hsd100pxn1";
+		backlight = <&backlight_lvds>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+};
+
+&ipu1_csi0_from_ipu1_csi0_mux {
+	bus-width = <8>;
+	data-shift = <12>; /* Lines 19:12 used */
+	hsync-active = <1>;
+	vync-active = <1>;
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+	remote-endpoint = <&ov5642_to_ipu1_csi0_mux>;
+};
+
+&ipu1_csi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ipu1_csi0>;
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	xceiver-supply = <&reg_can_xcvr>;
+	status = "okay";
+};
+
+&clks {
+	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
+			  <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
+	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>,
+				 <&clks IMX6QDL_CLK_PLL3_USB_OTG>;
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash: flash@0 {
+		compatible = "sst,sst25vf016b", "jedec,spi-nor";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy>;
+	phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			txen-skew-ps = <0>;
+			txc-skew-ps = <3000>;
+			rxdv-skew-ps = <0>;
+			rxc-skew-ps = <3000>;
+			rxd0-skew-ps = <0>;
+			rxd1-skew-ps = <0>;
+			rxd2-skew-ps = <0>;
+			rxd3-skew-ps = <0>;
+			txd0-skew-ps = <0>;
+			txd1-skew-ps = <0>;
+			txd2-skew-ps = <0>;
+			txd3-skew-ps = <0>;
+		};
+	};
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	codec: sgtl5000@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		clocks = <&clks IMX6QDL_CLK_CKO>;
+		VDDA-supply = <&reg_2p5v>;
+		VDDIO-supply = <&reg_3p3v>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	ov5640: camera@40 {
+		compatible = "ovti,ov5640";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ov5640>;
+		reg = <0x40>;
+		clocks = <&mipi_xclk>;
+		clock-names = "xclk";
+		DOVDD-supply = <&reg_1p8v>;
+		AVDD-supply = <&reg_2p8v>;
+		DVDD-supply = <&reg_1p5v>;
+		reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; /* NANDF_D5 */
+		powerdown-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>; /* NANDF_WP_B */
+
+		port {
+			ov5640_to_mipi_csi2: endpoint {
+				remote-endpoint = <&mipi_csi2_in>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+
+	ov5642: camera@42 {
+		compatible = "ovti,ov5642";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ov5642>;
+		clocks = <&clks IMX6QDL_CLK_CKO2>;
+		clock-names = "xclk";
+		reg = <0x42>;
+		reset-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+		powerdown-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+		gp-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+
+		port {
+			ov5642_to_ipu1_csi0_mux: endpoint {
+				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+				bus-width = <8>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+			};
+		};
+	};
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			/* SGTL5000 sys_mclk */
+			MX6QDL_PAD_GPIO_0__CCM_CLKO1    0x030b0
+		>;
+	};
+
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_DAT0__AUD4_RXD		0x130b0
+			MX6QDL_PAD_SD2_DAT3__AUD4_TXC		0x130b0
+			MX6QDL_PAD_SD2_DAT2__AUD4_TXD		0x110b0
+			MX6QDL_PAD_SD2_DAT1__AUD4_TXFS		0x130b0
+		>;
+	};
+
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b0
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX	0x1b0b0
+		>;
+	};
+
+	pinctrl_can_xcvr: can-xcvrgrp {
+		fsl,pins = <
+			/* Flexcan XCVR enable */
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1b0b0
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19  0x000b1	/* CS */
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x100b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x100b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x10030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x10030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x10030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x10030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x10030
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x10030
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x100b0
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
+			/* Phy reset */
+			MX6QDL_PAD_EIM_D23__GPIO3_IO23		0x000b0
+		>;
+	};
+
+	pinctrl_gpio_keys: gpio-keysgrp {
+		fsl,pins = <
+			/* Power Button */
+			MX6QDL_PAD_NANDF_D3__GPIO2_IO03		0x1b0b0
+			/* Menu Button */
+			MX6QDL_PAD_NANDF_D1__GPIO2_IO01		0x1b0b0
+			/* Home Button */
+			MX6QDL_PAD_NANDF_D4__GPIO2_IO04		0x1b0b0
+			/* Back Button */
+			MX6QDL_PAD_NANDF_D2__GPIO2_IO02		0x1b0b0
+			/* Volume Up Button */
+			MX6QDL_PAD_GPIO_18__GPIO7_IO13		0x1b0b0
+			/* Volume Down Button */
+			MX6QDL_PAD_GPIO_19__GPIO4_IO05		0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
+			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL		0x4001b8b1
+			MX6QDL_PAD_GPIO_16__I2C3_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_ipu1_csi0: ipu1csi0grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12    0x1b0b0
+			MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13    0x1b0b0
+			MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14    0x1b0b0
+			MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15    0x1b0b0
+			MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16    0x1b0b0
+			MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17    0x1b0b0
+			MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18    0x1b0b0
+			MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19    0x1b0b0
+			MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK   0x1b0b0
+			MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC      0x1b0b0
+			MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC     0x1b0b0
+			MX6QDL_PAD_CSI0_DATA_EN__IPU1_CSI0_DATA_EN 0x1b0b0
+		>;
+	};
+
+	pinctrl_j15: j15grp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
+			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15       0x10
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02        0x10
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03        0x10
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00   0x10
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01   0x10
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02   0x10
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03   0x10
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04   0x10
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05   0x10
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06   0x10
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07   0x10
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08   0x10
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09   0x10
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10  0x10
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11  0x10
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12  0x10
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13  0x10
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14  0x10
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15  0x10
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16  0x10
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17  0x10
+			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18  0x10
+			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19  0x10
+			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20  0x10
+			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21  0x10
+			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22  0x10
+			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23  0x10
+		>;
+	};
+
+	pinctrl_ov5640: ov5640grp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D5__GPIO2_IO05   0x000b0
+			MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09 0x0b0b0
+		>;
+	};
+
+	pinctrl_ov5642: ov5642grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT0__GPIO1_IO16 0x1b0b0
+			MX6QDL_PAD_GPIO_6__GPIO1_IO06   0x1b0b0
+			MX6QDL_PAD_GPIO_8__GPIO1_IO08   0x130b0
+			MX6QDL_PAD_GPIO_3__CCM_CLKO2    0x000b0
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT1__PWM3_OUT 0x1b0b1
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
+			MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D26__UART2_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D27__UART2_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbh1: usbh1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12		0x030b0
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
+			MX6QDL_PAD_KEY_COL4__USB_OTG_OC	0x1b0b0
+			/* power enable, high active */
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22  0x000b0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+			MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0	/* CD */
+			MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x1f0b0	/* WP */
+		>;
+	};
+
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
+			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059
+			MX6QDL_PAD_NANDF_D6__GPIO2_IO06 0x1b0b0	/* CD */
+		>;
+	};
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&lcd_display_in>;
+};
+
+&ldb {
+	status = "okay";
+
+	lvds-channel@0 {
+		status = "okay";
+
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+	status = "okay";
+};
+
+&ssi1 {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usb_h1_vbus>;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+};
+
+&usdhc4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	cd-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+};
+
+&mipi_csi {
+	status = "okay";
+
+	port@0 {
+		reg = <0>;
+
+		mipi_csi2_in: endpoint {
+			remote-endpoint = <&ov5640_to_mipi_csi2>;
+			clock-lanes = <0>;
+			data-lanes = <1 2>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi
index 0c0105468a2f..e8368c6b27ef 100644
--- a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi
@@ -71,21 +71,21 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_keys>;
 
-		power {
+		key-power {
 			label = "Power Button";
 			gpios = <&gpio3 29 GPIO_ACTIVE_LOW>;
 			wakeup-source;
 			linux,code = <KEY_POWER>;
 		};
 
-		volume-up {
+		key-volume-up {
 			label = "Volume Up";
 			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
 			wakeup-source;
 			linux,code = <KEY_VOLUMEUP>;
 		};
 
-		volume-down {
+		key-volume-down {
 			label = "Volume Down";
 			gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
 			wakeup-source;
@@ -113,13 +113,13 @@
 			"DMICDAT", "DMIC";
 		mux-int-port = <2>;
 		mux-ext-port = <3>;
-		hp-det-gpio = <&gpio7 8 GPIO_ACTIVE_LOW>;
-		mic-det-gpio = <&gpio1 9 GPIO_ACTIVE_LOW>;
+		hp-det-gpios = <&gpio7 8 GPIO_ACTIVE_LOW>;
+		mic-det-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
 	};
 
 	backlight_lvds: backlight-lvds {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 		status = "okay";
@@ -130,7 +130,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		red {
+		led-red {
 			gpios = <&gpio1 2 0>;
 			default-state = "on";
 		};
@@ -197,7 +197,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p32", "jedec,spi-nor";
@@ -311,8 +311,8 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_i2c2_egalax_int>;
 		interrupt-parent = <&gpio6>;
-		interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
-		wakeup-gpios = <&gpio6 8 GPIO_ACTIVE_HIGH>;
+		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+		wakeup-gpios = <&gpio6 8 GPIO_ACTIVE_LOW>;
 	};
 
 	ov5640: camera@3c {
@@ -338,7 +338,7 @@
 		};
 	};
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
 		reg = <0x08>;
 
@@ -450,8 +450,8 @@
 		compatible = "eeti,egalax_ts";
 		reg = <0x04>;
 		interrupt-parent = <&gpio6>;
-		interrupts = <7 2>;
-		wakeup-gpios = <&gpio6 7 0>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+		wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>;
 	};
 
 	magnetometer@e {
@@ -480,251 +480,247 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hog>;
 
-	imx6qdl-sabresd {
-		pinctrl_hog: hoggrp {
-			fsl,pins = <
-				MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b0b0
-				MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0
-				MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0
-				MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x1b0b0
-				MX6QDL_PAD_GPIO_0__CCM_CLKO1    0x130b0
-				MX6QDL_PAD_NANDF_CLE__GPIO6_IO07 0x1b0b0
-				MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x1b0b0
-				MX6QDL_PAD_EIM_D22__GPIO3_IO22  0x1b0b0
-				MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
-			>;
-		};
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b0b0
+			MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0
+			MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0
+			MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x1b0b0
+			MX6QDL_PAD_GPIO_0__CCM_CLKO1    0x130b0
+			MX6QDL_PAD_NANDF_CLE__GPIO6_IO07 0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x1b0b0
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22  0x1b0b0
+			MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+		>;
+	};
 
-		pinctrl_audmux: audmuxgrp {
-			fsl,pins = <
-				MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
-				MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
-				MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
-				MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
-			>;
-		};
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
+			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
+			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
+			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
+		>;
+	};
 
-		pinctrl_ecspi1: ecspi1grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL1__ECSPI1_MISO	0x100b1
-				MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI	0x100b1
-				MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK	0x100b1
-				MX6QDL_PAD_KEY_ROW1__GPIO4_IO09		0x1b0b0
-			>;
-		};
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL1__ECSPI1_MISO	0x100b1
+			MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI	0x100b1
+			MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK	0x100b1
+			MX6QDL_PAD_KEY_ROW1__GPIO4_IO09		0x1b0b0
+		>;
+	};
 
-		pinctrl_enet: enetgrp {
-			fsl,pins = <
-				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
-				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
-				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
-				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
-				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
-				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
-				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
-				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
-				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
-				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
-				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
-				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
-				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
-				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
-				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
-				MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
-			>;
-		};
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
+		>;
+	};
 
-		pinctrl_gpio_keys: gpio_keysgrp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1b0b0
-				MX6QDL_PAD_GPIO_4__GPIO1_IO04  0x1b0b0
-				MX6QDL_PAD_GPIO_5__GPIO1_IO05  0x1b0b0
-			>;
-		};
+	pinctrl_gpio_keys: gpio_keysgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1b0b0
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04  0x1b0b0
+			MX6QDL_PAD_GPIO_5__GPIO1_IO05  0x1b0b0
+		>;
+	};
 
-		pinctrl_hdmi_cec: hdmicecgrp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE	0x1f8b0
-			>;
-		};
+	pinctrl_hdmi_cec: hdmicecgrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE	0x1f8b0
+		>;
+	};
 
-		pinctrl_hp: hpgrp {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_RST__GPIO7_IO08          0x1b0b0
-				MX6QDL_PAD_GPIO_9__GPIO1_IO09           0x1b0b0
-			>;
-		};
+	pinctrl_hp: hpgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_RST__GPIO7_IO08          0x1b0b0
+			MX6QDL_PAD_GPIO_9__GPIO1_IO09           0x1b0b0
+		>;
+	};
 
-		pinctrl_i2c1: i2c1grp {
-			fsl,pins = <
-				MX6QDL_PAD_CSI0_DAT8__I2C1_SDA		0x4001b8b1
-				MX6QDL_PAD_CSI0_DAT9__I2C1_SCL		0x4001b8b1
-			>;
-		};
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA		0x4001b8b1
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL		0x4001b8b1
+		>;
+	};
 
-		pinctrl_i2c1_mma8451_int: i2c1mma8451intgrp {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_CMD__GPIO1_IO18		0xb0b1
-			>;
-		};
+	pinctrl_i2c1_mma8451_int: i2c1mma8451intgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__GPIO1_IO18		0xb0b1
+		>;
+	};
 
-		pinctrl_i2c2: i2c2grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
-				MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
-			>;
-		};
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
+		>;
+	};
 
-		pinctrl_i2c2_egalax_int: i2c2egalaxintgrp {
-			fsl,pins = <
-				MX6QDL_PAD_NANDF_ALE__GPIO6_IO08	0x1b0b0
-			>;
-		};
+	pinctrl_i2c2_egalax_int: i2c2egalaxintgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_ALE__GPIO6_IO08	0x1b0b0
+		>;
+	};
 
-		pinctrl_i2c3: i2c3grp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_3__I2C3_SCL		0x4001b8b1
-				MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
-			>;
-		};
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_3__I2C3_SCL		0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
+		>;
+	};
 
-		pinctrl_i2c3_isl29023_int: i2c3isl29023intgrp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_DA9__GPIO3_IO09		0xb0b1
-			>;
-		};
+	pinctrl_i2c3_isl29023_int: i2c3isl29023intgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_DA9__GPIO3_IO09		0xb0b1
+		>;
+	};
 
-		pinctrl_i2c3_mag3110_int: i2c3mag3110intgrp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D16__GPIO3_IO16		0xb0b1
-			>;
-		};
+	pinctrl_i2c3_mag3110_int: i2c3mag3110intgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D16__GPIO3_IO16		0xb0b1
+		>;
+	};
 
-		pinctrl_ipu1_csi0: ipu1csi0grp {
-			fsl,pins = <
-				MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12    0x1b0b0
-				MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13    0x1b0b0
-				MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14    0x1b0b0
-				MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15    0x1b0b0
-				MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16    0x1b0b0
-				MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17    0x1b0b0
-				MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18    0x1b0b0
-				MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19    0x1b0b0
-				MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK   0x1b0b0
-				MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC      0x1b0b0
-				MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC     0x1b0b0
-			>;
-		};
+	pinctrl_ipu1_csi0: ipu1csi0grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12    0x1b0b0
+			MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13    0x1b0b0
+			MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14    0x1b0b0
+			MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15    0x1b0b0
+			MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16    0x1b0b0
+			MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17    0x1b0b0
+			MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18    0x1b0b0
+			MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19    0x1b0b0
+			MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK   0x1b0b0
+			MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC      0x1b0b0
+			MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC     0x1b0b0
+		>;
+	};
 
-		pinctrl_ov5640: ov5640grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_DAT2__GPIO1_IO19 0x1b0b0
-				MX6QDL_PAD_SD1_CLK__GPIO1_IO20  0x1b0b0
-			>;
-		};
+	pinctrl_ov5640: ov5640grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT2__GPIO1_IO19 0x1b0b0
+			MX6QDL_PAD_SD1_CLK__GPIO1_IO20  0x1b0b0
+		>;
+	};
 
-		pinctrl_ov5642: ov5642grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_DAT0__GPIO1_IO16 0x1b0b0
-				MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x1b0b0
-			>;
-		};
+	pinctrl_ov5642: ov5642grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT0__GPIO1_IO16 0x1b0b0
+			MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x1b0b0
+		>;
+	};
 
-		pinctrl_pcie: pciegrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_17__GPIO7_IO12	0x1b0b0
-			>;
-		};
+	pinctrl_pcie: pciegrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12	0x1b0b0
+		>;
+	};
 
-		pinctrl_pcie_reg: pciereggrp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D19__GPIO3_IO19	0x1b0b0
-			>;
-		};
+	pinctrl_pcie_reg: pciereggrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19	0x1b0b0
+		>;
+	};
 
-		pinctrl_pwm1: pwm1grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_DAT3__PWM1_OUT		0x1b0b1
-			>;
-		};
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT3__PWM1_OUT		0x1b0b1
+		>;
+	};
 
-		pinctrl_sensors_reg: sensorsreggrp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_EB3__GPIO2_IO31		0x1b0b0
-			>;
-		};
+	pinctrl_sensors_reg: sensorsreggrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_EB3__GPIO2_IO31		0x1b0b0
+		>;
+	};
 
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0b1
-				MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0b1
-			>;
-		};
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0b1
+		>;
+	};
 
-		pinctrl_usbotg: usbotggrp {
-			fsl,pins = <
-				MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x17059
-			>;
-		};
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID	0x17059
+		>;
+	};
 
-		pinctrl_usdhc2: usdhc2grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
-				MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
-				MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
-				MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
-				MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
-				MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
-				MX6QDL_PAD_NANDF_D4__SD2_DATA4		0x17059
-				MX6QDL_PAD_NANDF_D5__SD2_DATA5		0x17059
-				MX6QDL_PAD_NANDF_D6__SD2_DATA6		0x17059
-				MX6QDL_PAD_NANDF_D7__SD2_DATA7		0x17059
-			>;
-		};
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+			MX6QDL_PAD_NANDF_D4__SD2_DATA4		0x17059
+			MX6QDL_PAD_NANDF_D5__SD2_DATA5		0x17059
+			MX6QDL_PAD_NANDF_D6__SD2_DATA6		0x17059
+			MX6QDL_PAD_NANDF_D7__SD2_DATA7		0x17059
+		>;
+	};
 
-		pinctrl_usdhc3: usdhc3grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
-				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
-				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
-				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
-				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
-				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
-				MX6QDL_PAD_SD3_DAT4__SD3_DATA4		0x17059
-				MX6QDL_PAD_SD3_DAT5__SD3_DATA5		0x17059
-				MX6QDL_PAD_SD3_DAT6__SD3_DATA6		0x17059
-				MX6QDL_PAD_SD3_DAT7__SD3_DATA7		0x17059
-			>;
-		};
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4		0x17059
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5		0x17059
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6		0x17059
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7		0x17059
+		>;
+	};
 
-		pinctrl_usdhc4: usdhc4grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
-				MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
-				MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
-				MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
-				MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
-				MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059
-				MX6QDL_PAD_SD4_DAT4__SD4_DATA4		0x17059
-				MX6QDL_PAD_SD4_DAT5__SD4_DATA5		0x17059
-				MX6QDL_PAD_SD4_DAT6__SD4_DATA6		0x17059
-				MX6QDL_PAD_SD4_DAT7__SD4_DATA7		0x17059
-			>;
-		};
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
+			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059
+			MX6QDL_PAD_SD4_DAT4__SD4_DATA4		0x17059
+			MX6QDL_PAD_SD4_DAT5__SD4_DATA5		0x17059
+			MX6QDL_PAD_SD4_DAT6__SD4_DATA6		0x17059
+			MX6QDL_PAD_SD4_DAT7__SD4_DATA7		0x17059
+		>;
+	};
 
-		pinctrl_wdog: wdoggrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_1__WDOG2_B		0x1b0b0
-			>;
-		};
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__WDOG2_B		0x1b0b0
+		>;
 	};
 
-	gpio_leds {
-		pinctrl_gpio_leds: gpioledsgrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
-			>;
-		};
+	pinctrl_gpio_leds: gpioledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
+		>;
 	};
 };
 
@@ -755,7 +751,6 @@
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
@@ -809,6 +804,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usbotg>;
 	disable-over-current;
+	dr_mode = "otg";
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-savageboard.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-savageboard.dtsi
index 02e6d36e85fa..2daf2b6af884 100644
--- a/arch/arm/boot/dts/imx6qdl-savageboard.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-savageboard.dtsi
@@ -58,7 +58,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_keys>;
 
-		power {
+		key-power {
 			gpios = <&gpio3 7 GPIO_ACTIVE_LOW>;
 			label = "Power Button";
 			linux,code = <KEY_POWER>;
@@ -83,7 +83,7 @@
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <4>;
 		power-supply = <&reg_3p3v>;
-		pwms = <&pwm1 0 10000>;
+		pwms = <&pwm1 0 10000 0>;
 	};
 
 	reg_3p3v: regulator-3p3v {
@@ -140,7 +140,6 @@
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6qdl-skov-cpu-revc.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-skov-cpu-revc.dtsi
index 69ae430a53bd..596b3bb3ddd1 100644
--- a/arch/arm/boot/dts/imx6qdl-skov-cpu-revc.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-skov-cpu-revc.dtsi
@@ -2,35 +2,60 @@
 //
 // Copyright (C) 2020 Pengutronix, Ulrich Oelmann <kernel@pengutronix.de>
 
+/ {
+	touchscreen {
+		compatible = "resistive-adc-touch";
+		io-channels = <&adc_ts 1>, <&adc_ts 3>, <&adc_ts 4>, <&adc_ts 5>;
+		io-channel-names = "y", "z1", "z2", "x";
+		touchscreen-min-pressure = <65000>;
+		touchscreen-inverted-y;
+		touchscreen-swapped-x-y;
+		touchscreen-x-plate-ohms = <300>;
+		touchscreen-y-plate-ohms = <800>;
+	};
+};
+
 &ecspi4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi4>;
 	cs-gpios = <&gpio3 20 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
-	touchscreen@0 {
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_touch>;
-		compatible = "ti,tsc2046";
+	adc_ts: adc@0 {
+		compatible = "ti,tsc2046e-adc";
 		reg = <0>;
+		pinctrl-0 = <&pinctrl_touch>;
+		pinctrl-names = "default";
 		spi-max-frequency = <1000000>;
 		interrupts-extended = <&gpio3 19 IRQ_TYPE_LEVEL_LOW>;
-		vcc-supply  = <&reg_3v3>;
-		pendown-gpio = <&gpio3 19 GPIO_ACTIVE_LOW>;
-		ti,x-plate-ohms = /bits/ 16 <850>;
-		ti,y-plate-ohms = /bits/ 16 <295>;
-		ti,pressure-min = /bits/ 16 <2>;
-		ti,pressure-max = /bits/ 16 <1500>;
-		ti,vref-mv	= /bits/ 16 <3300>;
-		ti,settle-delay-usec = /bits/ 16 <15>;
-		ti,vref-delay-usecs = /bits/ 16 <0>;
-		ti,penirq-recheck-delay-usecs = /bits/ 16 <100>;
-		ti,debounce-max = /bits/ 16 <100>;
-		ti,debounce-tol = /bits/ 16 <(~0)>;
-		ti,debounce-rep = /bits/ 16 <4>;
-		touchscreen-swapped-x-y;
-		touchscreen-inverted-y;
-		wakeup-source;
+		#io-channel-cells = <1>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@1 {
+			reg = <1>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@3 {
+			reg = <3>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@4 {
+			reg = <4>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@5 {
+			reg = <5>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-skov-cpu.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-skov-cpu.dtsi
index 77a91a97e6cf..6ab71a729fd8 100644
--- a/arch/arm/boot/dts/imx6qdl-skov-cpu.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-skov-cpu.dtsi
@@ -13,10 +13,14 @@
 	aliases {
 		can0 = &can1;
 		can1 = &can2;
+		ethernet0 = &fec;
+		ethernet1 = &lan1;
+		ethernet2 = &lan2;
 		mdio-gpio0 = &mdio;
 		nand = &gpmi;
 		rtc0 = &i2c_rtc;
 		rtc1 = &snvs;
+		switch0 = &switch;
 		usb0 = &usbh1;
 		usb1 = &usbotg;
 	};
@@ -60,7 +64,7 @@
 		gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>,
 			<&gpio1 22 GPIO_ACTIVE_HIGH>;
 
-		switch@0 {
+		switch: switch@0 {
 			compatible = "microchip,ksz8873";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_switch>;
@@ -73,13 +77,13 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				ports@0 {
+				lan1: ports@0 {
 					reg = <0>;
 					phy-mode = "internal";
 					label = "lan1";
 				};
 
-				ports@1 {
+				lan2: ports@1 {
 					reg = <1>;
 					phy-mode = "internal";
 					label = "lan2";
@@ -105,6 +109,7 @@
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <50000000>;
+		clock-output-names = "enet_ref_pad";
 	};
 
 	reg_3v3: regulator-3v3 {
@@ -149,6 +154,16 @@
 		gpio = <&gpio4 11 GPIO_ACTIVE_LOW>;
 	};
 
+	reg_tft_vcom: regulator-tft-vcom {
+		compatible = "pwm-regulator";
+		pwms = <&pwm3 0 20000 0>;
+		regulator-name = "tft_vcom";
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+		regulator-always-on;
+		voltage-table = <3600000 26>;
+	};
+
 	reg_vcc_mmc: regulator-vcc-mmc {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
@@ -222,13 +237,16 @@
 	};
 };
 
+&clks {
+	clocks = <&clk50m_phy>;
+	clock-names = "enet_ref_pad";
+	assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+	assigned-clock-parents = <&clk50m_phy>;
+};
+
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	clocks = <&clks IMX6QDL_CLK_ENET>,
-		 <&clks IMX6QDL_CLK_ENET>,
-		 <&clk50m_phy>;
-	clock-names = "ipg", "ahb", "ptp";
 	phy-mode = "rmii";
 	phy-supply = <&reg_3v3>;
 	status = "okay";
@@ -264,7 +282,6 @@
 &pwm2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm2>;
-	#pwm-cells = <2>;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-skov-revc-lt2.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-skov-revc-lt2.dtsi
index 48c9ce051f47..48c9ce051f47 100644
--- a/arch/arm/boot/dts/imx6qdl-skov-revc-lt2.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-skov-revc-lt2.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-solidsense.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-solidsense.dtsi
index 234827e554d0..60e446ba8f52 100644
--- a/arch/arm/boot/dts/imx6qdl-solidsense.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-solidsense.dtsi
@@ -93,49 +93,47 @@
 &iomuxc {
 	pinctrl-0 = <&pinctrl_hog>, <&pinctrl_solidsense_hog>;
 
-	solidsense {
-		pinctrl_solidsense_hog: solidsense-hog {
-			fsl,pins = <
-				/* Nordic RESET_N */
-				MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x400130b1
-				/* Nordic Chip 1 SWDIO - GPIO 125 */
-				MX6QDL_PAD_DISP0_DAT8__GPIO4_IO29 0x400130b1
-				/* Nordic Chip 1 SWDCLK - GPIO 59 */
-				/* already claimed in the HB2 hogs */
-				/* MX6QDL_PAD_EIM_LBA__GPIO2_IO27 0x400130b1 */
-				/* Nordic Chip 2 SWDIO - GPIO 81 */
-				MX6QDL_PAD_EIM_D17__GPIO3_IO17 0x400130b1
-				/* Nordic Chip 2 SWCLK - GPIO 82 */
-				MX6QDL_PAD_EIM_D18__GPIO3_IO18 0x400130b1
-			>;
-		};
+	pinctrl_solidsense_hog: solidsense-hoggrp {
+		fsl,pins = <
+			/* Nordic RESET_N */
+			MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x400130b1
+			/* Nordic Chip 1 SWDIO - GPIO 125 */
+			MX6QDL_PAD_DISP0_DAT8__GPIO4_IO29 0x400130b1
+			/* Nordic Chip 1 SWDCLK - GPIO 59 */
+			/* already claimed in the HB2 hogs */
+			/* MX6QDL_PAD_EIM_LBA__GPIO2_IO27 0x400130b1 */
+			/* Nordic Chip 2 SWDIO - GPIO 81 */
+			MX6QDL_PAD_EIM_D17__GPIO3_IO17 0x400130b1
+			/* Nordic Chip 2 SWCLK - GPIO 82 */
+			MX6QDL_PAD_EIM_D18__GPIO3_IO18 0x400130b1
+		>;
+	};
 
-		pinctrl_solidsense_leds: solidsense-leds {
-			fsl,pins = <
-				/* Red LED 1 - GPIO 58 */
-				MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x400130b1
-				/* Green LED 1 - GPIO 55 */
-				MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x400130b1
-				/* Red LED 2 - GPIO 57 */
-				MX6QDL_PAD_EIM_OE__GPIO2_IO25 0x400130b1
-				/* Green LED 2 - GPIO 56 */
-				MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x400130b1
-			>;
-		};
+	pinctrl_solidsense_leds: solidsense-ledsgrp {
+		fsl,pins = <
+			/* Red LED 1 - GPIO 58 */
+			MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x400130b1
+			/* Green LED 1 - GPIO 55 */
+			MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x400130b1
+			/* Red LED 2 - GPIO 57 */
+			MX6QDL_PAD_EIM_OE__GPIO2_IO25 0x400130b1
+			/* Green LED 2 - GPIO 56 */
+			MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x400130b1
+		>;
+	};
 
-		pinctrl_solidsense_uart2: solidsense-uart2 {
-			fsl,pins = <
-				MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA	0x1b0b1
-				MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA	0x1b0b1
-			>;
-		};
+	pinctrl_solidsense_uart2: solidsense-uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA	0x1b0b1
+			MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA	0x1b0b1
+		>;
+	};
 
-		pinctrl_solidsense_uart3: solidsense-uart3 {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
-				MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
-			>;
-		};
+	pinctrl_solidsense_uart3: solidsense-uart3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
+		>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-sr-som-brcm.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-sr-som-brcm.dtsi
index b55af61dfeca..e491f5c9d455 100644
--- a/arch/arm/boot/dts/imx6qdl-sr-som-brcm.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-sr-som-brcm.dtsi
@@ -70,55 +70,53 @@
 };
 
 &iomuxc {
-	microsom {
-		pinctrl_microsom_brcm_bt: microsom-brcm-bt {
-			fsl,pins = <
-				MX6QDL_PAD_CSI0_DAT14__GPIO6_IO00	0x40013070
-				MX6QDL_PAD_CSI0_DAT15__GPIO6_IO01	0x40013070
-				MX6QDL_PAD_CSI0_DAT18__GPIO6_IO04	0x40013070
-			>;
-		};
+	pinctrl_microsom_brcm_bt: microsom-brcm-btgrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT14__GPIO6_IO00	0x40013070
+			MX6QDL_PAD_CSI0_DAT15__GPIO6_IO01	0x40013070
+			MX6QDL_PAD_CSI0_DAT18__GPIO6_IO04	0x40013070
+		>;
+	};
 
-		pinctrl_microsom_brcm_osc: microsom-brcm-osc {
-			fsl,pins = <
-				MX6QDL_PAD_DISP0_DAT11__GPIO5_IO05	0x40013070
-			>;
-		};
+	pinctrl_microsom_brcm_osc: microsom-brcm-oscgrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT11__GPIO5_IO05	0x40013070
+		>;
+	};
 
-		pinctrl_microsom_brcm_reg: microsom-brcm-reg {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D19__GPIO3_IO19		0x40013070
-			>;
-		};
+	pinctrl_microsom_brcm_reg: microsom-brcm-reggrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19		0x40013070
+		>;
+	};
 
-		pinctrl_microsom_brcm_wifi: microsom-brcm-wifi {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_8__XTALOSC_REF_CLK_32K	0x1b0b0
-				MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20	0x40013070
-				MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26	0x40013070
-				MX6QDL_PAD_CSI0_DAT9__GPIO5_IO27	0x40013070
-			>;
-		};
+	pinctrl_microsom_brcm_wifi: microsom-brcm-wifigrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_8__XTALOSC_REF_CLK_32K	0x1b0b0
+			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20	0x40013070
+			MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26	0x40013070
+			MX6QDL_PAD_CSI0_DAT9__GPIO5_IO27	0x40013070
+		>;
+	};
 
-		pinctrl_microsom_uart4: microsom-uart4 {
-			fsl,pins = <
-				MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x1b0b1
-				MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x1b0b1
-				MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B 0x1b0b1
-				MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B 0x1b0b1
-			>;
-		};
+	pinctrl_microsom_uart4: microsom-uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x1b0b1
+			MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x1b0b1
+			MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B 0x1b0b1
+			MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B 0x1b0b1
+		>;
+	};
 
-		pinctrl_microsom_usdhc1: microsom-usdhc1 {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_CMD__SD1_CMD    0x17059
-				MX6QDL_PAD_SD1_CLK__SD1_CLK    0x10059
-				MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
-				MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
-				MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
-				MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
-			>;
-		};
+	pinctrl_microsom_usdhc1: microsom-usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD    0x17059
+			MX6QDL_PAD_SD1_CLK__SD1_CLK    0x10059
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
+		>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-sr-som-emmc.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-sr-som-emmc.dtsi
index 5f3b8baab20f..ddca24414d26 100644
--- a/arch/arm/boot/dts/imx6qdl-sr-som-emmc.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-sr-som-emmc.dtsi
@@ -40,22 +40,20 @@
  */
 
 &iomuxc {
-	microsom {
-		pinctrl_microsom_usdhc3: microsom-usdhc3 {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_CMD__SD3_CMD    0x17059
-				MX6QDL_PAD_SD3_CLK__SD3_CLK    0x10059
-				MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
-				MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
-				MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
-				MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
-				MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059
-				MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059
-				MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059
-				MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
-				MX6QDL_PAD_SD3_RST__SD3_RESET  0x17059
-			>;
-		};
+	pinctrl_microsom_usdhc3: microsom-usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD    0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK    0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
+			MX6QDL_PAD_SD3_RST__SD3_RESET  0x17059
+		>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-sr-som-ti.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-sr-som-ti.dtsi
index 352ac585ca6b..cd1e682f11ad 100644
--- a/arch/arm/boot/dts/imx6qdl-sr-som-ti.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-sr-som-ti.dtsi
@@ -76,56 +76,54 @@
 };
 
 &iomuxc {
-	microsom {
-		pinctrl_microsom_ti_bt: microsom-ti-bt {
-			fsl,pins = <
-				/* BT_EN_SOC */
-				MX6QDL_PAD_CSI0_DAT14__GPIO6_IO00	0x40013070
-			>;
-		};
+	pinctrl_microsom_ti_bt: microsom-ti-btgrp {
+		fsl,pins = <
+			/* BT_EN_SOC */
+			MX6QDL_PAD_CSI0_DAT14__GPIO6_IO00	0x40013070
+		>;
+	};
 
-		pinctrl_microsom_ti_clk: microsom-ti-clk {
-			fsl,pins = <
-				/* EXT_32K */
-				MX6QDL_PAD_GPIO_8__XTALOSC_REF_CLK_32K	0x1b0b0
-				/* WL_XTAL_PU (unrouted) */
-				MX6QDL_PAD_DISP0_DAT11__GPIO5_IO05 0x40013070
-			>;
-		};
+	pinctrl_microsom_ti_clk: microsom-ti-clkgrp {
+		fsl,pins = <
+			/* EXT_32K */
+			MX6QDL_PAD_GPIO_8__XTALOSC_REF_CLK_32K	0x1b0b0
+			/* WL_XTAL_PU (unrouted) */
+			MX6QDL_PAD_DISP0_DAT11__GPIO5_IO05 0x40013070
+		>;
+	};
 
-		pinctrl_microsom_ti_wifi_en: microsom-ti-wifi-en {
-			fsl,pins = <
-				/* WLAN_EN_SOC */
-				MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26	0x40013070
-			>;
-		};
+	pinctrl_microsom_ti_wifi_en: microsom-ti-wifi-engrp {
+		fsl,pins = <
+			/* WLAN_EN_SOC */
+			MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26	0x40013070
+		>;
+	};
 
-		pinctrl_microsom_ti_wifi_irq: microsom-ti-wifi-irq {
-			fsl,pins = <
-				/* WLAN_IRQ */
-				MX6QDL_PAD_CSI0_DAT18__GPIO6_IO04	0x40013070
-			>;
-		};
+	pinctrl_microsom_ti_wifi_irq: microsom-ti-wifi-irqgrp {
+		fsl,pins = <
+			/* WLAN_IRQ */
+			MX6QDL_PAD_CSI0_DAT18__GPIO6_IO04	0x40013070
+		>;
+	};
 
-		pinctrl_microsom_uart4: microsom-uart4 {
-			fsl,pins = <
-				MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x1b0b1
-				MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x1b0b1
-				MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B 0x1b0b1
-				MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B 0x1b0b1
-			>;
-		};
+	pinctrl_microsom_uart4: microsom-uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x1b0b1
+			MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x1b0b1
+			MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B 0x1b0b1
+			MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B 0x1b0b1
+		>;
+	};
 
-		pinctrl_microsom_usdhc1: microsom-usdhc1 {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_CMD__SD1_CMD    0x17059
-				MX6QDL_PAD_SD1_CLK__SD1_CLK    0x10059
-				MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
-				MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
-				MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
-				MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
-			>;
-		};
+	pinctrl_microsom_usdhc1: microsom-usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD    0x17059
+			MX6QDL_PAD_SD1_CLK__SD1_CLK    0x10059
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
+		>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-sr-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-sr-som.dtsi
index f86efd0ccc40..7af74b203e39 100644
--- a/arch/arm/boot/dts/imx6qdl-sr-som.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-sr-som.dtsi
@@ -83,61 +83,69 @@
 			qca,clk-out-frequency = <125000000>;
 			qca,smarteee-tw-us-1g = <24>;
 		};
+
+		/*
+		 * ADIN1300 (som rev 1.9 or later) is always at address 1. It
+		 * will be enabled automatically by U-Boot if detected.
+		 */
+		ethernet-phy@1 {
+			reg = <1>;
+			adi,phy-output-clock = "125mhz-free-running";
+			status = "disabled";
+		};
 	};
 };
 
 &iomuxc {
-	microsom {
-		pinctrl_microsom_enet_ar8035: microsom-enet-ar8035 {
-			fsl,pins = <
-				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b8b0
-				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
-				/* AR8035 reset */
-				MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x130b0
-				/* AR8035 interrupt */
-				MX6QDL_PAD_DI0_PIN2__GPIO4_IO18		0x1b0b0
-				/* GPIO16 -> AR8035 25MHz */
-				MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0b0
-				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x13030
-				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
-				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
-				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
-				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
-				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
-				/* AR8035 CLK_25M --> ENET_REF_CLK (V22) */
-				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x0a0b1
-				/* AR8035 pin strapping: IO voltage: pull up */
-				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
-				/* AR8035 pin strapping: PHYADDR#0: pull down */
-				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x13030
-				/* AR8035 pin strapping: PHYADDR#1: pull down */
-				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x13030
-				/* AR8035 pin strapping: MODE#1: pull up */
-				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
-				/* AR8035 pin strapping: MODE#3: pull up */
-				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
-				/* AR8035 pin strapping: MODE#0: pull down */
-				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x13030
+	pinctrl_microsom_enet_ar8035: microsom-enet-ar8035grp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b8b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			/* AR8035 reset */
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x130b0
+			/* AR8035 interrupt */
+			MX6QDL_PAD_DI0_PIN2__GPIO4_IO18		0x1b0b0
+			/* GPIO16 -> AR8035 25MHz */
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x13030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
+			/* AR8035 CLK_25M --> ENET_REF_CLK (V22) */
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x0a0b1
+			/* AR8035 pin strapping: IO voltage: pull up */
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+			/* AR8035 pin strapping: PHYADDR#0: pull down */
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x13030
+			/* AR8035 pin strapping: PHYADDR#1: pull down */
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x13030
+			/* AR8035 pin strapping: MODE#1: pull up */
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+			/* AR8035 pin strapping: MODE#3: pull up */
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+			/* AR8035 pin strapping: MODE#0: pull down */
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x13030
 
-				/*
-				 * As the RMII pins are also connected to RGMII
-				 * so that an AR8030 can be placed, set these
-				 * to high-z with the same pulls as above.
-				 * Use the GPIO settings to avoid changing the
-				 * input select registers.
-				 */
-				MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25	0x03000
-				MX6QDL_PAD_ENET_RXD0__GPIO1_IO27	0x03000
-				MX6QDL_PAD_ENET_RXD1__GPIO1_IO26	0x03000
-			>;
-		};
+			/*
+			 * As the RMII pins are also connected to RGMII
+			 * so that an AR8030 can be placed, set these
+			 * to high-z with the same pulls as above.
+			 * Use the GPIO settings to avoid changing the
+			 * input select registers.
+			 */
+			MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25	0x03000
+			MX6QDL_PAD_ENET_RXD0__GPIO1_IO27	0x03000
+			MX6QDL_PAD_ENET_RXD1__GPIO1_IO26	0x03000
+		>;
+	};
 
-		pinctrl_microsom_uart1: microsom-uart1 {
-			fsl,pins = <
-				MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0b1
-				MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0b1
-			>;
-		};
+	pinctrl_microsom_uart1: microsom-uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0b1
+		>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-tqma6.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-tqma6.dtsi
index 344ea935c7da..07492f63a1f8 100644
--- a/arch/arm/boot/dts/imx6qdl-tqma6.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-tqma6.dtsi
@@ -7,16 +7,6 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 
-/ {
-	reg_3p3v: regulator-3p3v {
-		compatible = "regulator-fixed";
-		regulator-name = "supply-3p3v";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-};
-
 &ecspi1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
@@ -25,11 +15,16 @@
 
 	m25p80: flash@0 {
 		compatible = "jedec,spi-nor";
-		spi-max-frequency = <50000000>;
 		reg = <0>;
-		#address-cells = <1>;
-		#size-cells = <1>;
+		spi-max-frequency = <50000000>;
+		vcc-supply = <&sw4_reg>;
 		m25p,fast-read;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+		};
 	};
 };
 
@@ -59,20 +54,6 @@
 		>;
 	};
 
-	pinctrl_i2c3: i2c3grp {
-		fsl,pins = <
-			MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b899
-			MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b899
-		>;
-	};
-
-	pinctrl_i2c3_recovery: i2c3recoverygrp {
-		fsl,pins = <
-			MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x4001b899
-			MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x4001b899
-		>;
-	};
-
 	pinctrl_pmic: pmicgrp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 0x1b099 /* PMIC irq */
@@ -133,7 +114,7 @@
 		};
 
 		sw4_reg: sw4 {
-			regulator-min-microvolt = <800000>;
+			regulator-min-microvolt = <3300000>;
 			regulator-max-microvolt = <3300000>;
 			regulator-always-on;
 		};
@@ -197,7 +178,7 @@
 &usdhc3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc3>;
-	vmmc-supply = <&reg_3p3v>;
+	vmmc-supply = <&sw4_reg>;
 	non-removable;
 	disable-wp;
 	no-sd;
diff --git a/arch/arm/boot/dts/imx6qdl-tqma6a.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-tqma6a.dtsi
index 7dc3f0005b0f..e8fd37dd8835 100644
--- a/arch/arm/boot/dts/imx6qdl-tqma6a.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-tqma6a.dtsi
@@ -7,6 +7,7 @@
 #include <dt-bindings/gpio/gpio.h>
 
 &fec {
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
@@ -26,15 +27,17 @@
 		reg = <0x08>;
 	};
 
-	sensor@48 {
-		compatible = "national,lm75";
+	temperature-sensor@48 {
+		compatible = "national,lm75a";
 		reg = <0x48>;
+		vs-supply = <&sw4_reg>;
 	};
 
 	eeprom@50 {
 		compatible = "st,24c64", "atmel,24c64";
 		reg = <0x50>;
 		pagesize = <32>;
+		vcc-supply = <&sw4_reg>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-tqma6b.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-tqma6b.dtsi
index dd0925766440..0e404c1f62f2 100644
--- a/arch/arm/boot/dts/imx6qdl-tqma6b.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-tqma6b.dtsi
@@ -20,14 +20,32 @@
 		reg = <0x08>;
 	};
 
-	sensor@48 {
-		compatible = "national,lm75";
+	temperature-sensor@48 {
+		compatible = "national,lm75a";
 		reg = <0x48>;
+		vs-supply = <&sw4_reg>;
 	};
 
 	eeprom@50 {
 		compatible = "st,24c64", "atmel,24c64";
 		reg = <0x50>;
 		pagesize = <32>;
+		vcc-supply = <&sw4_reg>;
+	};
+};
+
+&iomuxc {
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b899
+			MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b899
+		>;
+	};
+
+	pinctrl_i2c3_recovery: i2c3recoverygrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x4001b899
+			MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x4001b899
+		>;
 	};
 };
diff --git a/arch/arm/boot/dts/imx6qdl-ts4900.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-ts4900.dtsi
index f88da757edda..f88da757edda 100644
--- a/arch/arm/boot/dts/imx6qdl-ts4900.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-ts4900.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-ts7970.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-ts7970.dtsi
index fded07f370b3..17f6a568f0e8 100644
--- a/arch/arm/boot/dts/imx6qdl-ts7970.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-ts7970.dtsi
@@ -73,13 +73,13 @@
 			default-state = "off";
 		};
 
-		en-usb-5v {
+		en-usb-5v-led {
 			label = "en-usb-5v";
 			gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 		};
 
-		sel_dc_usb {
+		sel-dc-usb-led {
 			label = "sel_dc_usb";
 			gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
@@ -192,6 +192,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
@@ -212,12 +213,12 @@
 	status = "okay";
 
 	m41t00s: rtc@68 {
-		compatible = "m41t00";
+		compatible = "st,m41t00";
 		reg = <0x68>;
 	};
 
 	isl12022: rtc@6f {
-		compatible = "isl,isl12022";
+		compatible = "isil,isl12022";
 		reg = <0x6f>;
 	};
 
@@ -226,7 +227,7 @@
 		reg = <0x28>;
 		#gpio-cells = <2>;
 		gpio-controller;
-		ngpio = <32>;
+		ngpios = <62>;
 	};
 
 	sgtl5000: codec@a {
@@ -234,6 +235,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_sgtl5000>;
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
 		VDDA-supply = <&reg_3p3v>;
 		VDDIO-supply = <&reg_3p3v>;
@@ -263,7 +265,7 @@
 		>;
 	};
 
-	pinctrl_ecspi2: ecspi2 {
+	pinctrl_ecspi2: ecspi2grp {
 		fsl,pins = <
 			MX6QDL_PAD_CSI0_DAT8__ECSPI2_SCLK      0x100b1
 			MX6QDL_PAD_CSI0_DAT9__ECSPI2_MOSI      0x100b1
@@ -278,7 +280,7 @@
 		>;
 	};
 
-	pinctrl_enet: enet {
+	pinctrl_enet: enetgrp {
 		fsl,pins = <
 			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
 			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
diff --git a/arch/arm/boot/dts/imx6qdl-tx6-lcd.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-tx6-lcd.dtsi
index 79f2354886b7..cdeaca36867e 100644
--- a/arch/arm/boot/dts/imx6qdl-tx6-lcd.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-tx6-lcd.dtsi
@@ -1,42 +1,6 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
 /*
  * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 / {
@@ -51,7 +15,6 @@
 		pinctrl-0 = <&pinctrl_lcd1_pwr>;
 		enable-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>;
 		power-supply = <&reg_3v3>;
-		turn-on-delay-ms = <35>;
 		/*
 		 * a poor man's way to create a 1:1 relationship between
 		 * the PWM value and the actual duty cycle
@@ -110,7 +73,7 @@
 		};
 
 		display-timings {
-			VGA {
+			timing-vga {
 				clock-frequency = <25200000>;
 				hactive = <640>;
 				vactive = <480>;
@@ -126,8 +89,7 @@
 				pixelclk-active = <0>;
 			};
 
-			ETV570 {
-				u-boot,panel-name = "edt,et057090dhu";
+			timing-etv570 {
 				clock-frequency = <25200000>;
 				hactive = <640>;
 				vactive = <480>;
@@ -143,8 +105,7 @@
 				pixelclk-active = <0>;
 			};
 
-			ET0350 {
-				u-boot,panel-name = "edt,et0350g0dh6";
+			timing-et0350 {
 				clock-frequency = <6413760>;
 				hactive = <320>;
 				vactive = <240>;
@@ -160,8 +121,7 @@
 				pixelclk-active = <0>;
 			};
 
-			ET0430 {
-				u-boot,panel-name = "edt,et0430g0dh6";
+			timing-et0430 {
 				clock-frequency = <9009000>;
 				hactive = <480>;
 				vactive = <272>;
@@ -177,7 +137,7 @@
 				pixelclk-active = <1>;
 			};
 
-			ET0500 {
+			timing-et0500 {
 				clock-frequency = <33264000>;
 				hactive = <800>;
 				vactive = <480>;
@@ -193,8 +153,7 @@
 				pixelclk-active = <0>;
 			};
 
-			ET0700 { /* same as ET0500 */
-				u-boot,panel-name = "edt,etm0700g0dh6";
+			timing-et0700 { /* same as ET0500 */
 				clock-frequency = <33264000>;
 				hactive = <800>;
 				vactive = <480>;
@@ -210,7 +169,7 @@
 				pixelclk-active = <0>;
 			};
 
-			ETQ570 {
+			timing-etq570 {
 				clock-frequency = <6596040>;
 				hactive = <320>;
 				vactive = <240>;
@@ -226,8 +185,7 @@
 				pixelclk-active = <0>;
 			};
 
-			CoMTFT { /* same as ET0700 but with inverted pixel clock */
-				u-boot,panel-name = "edt,etm0700g0edh6";
+			timing-comtft { /* same as ET0700 but with inverted pixel clock */
 				clock-frequency = <33264000>;
 				hactive = <800>;
 				vactive = <480>;
diff --git a/arch/arm/boot/dts/imx6qdl-tx6-lvds.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-tx6-lvds.dtsi
index 2ca2eb37e14f..63d09c01a3c6 100644
--- a/arch/arm/boot/dts/imx6qdl-tx6-lvds.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-tx6-lvds.dtsi
@@ -1,42 +1,6 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
 /*
  * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 / {
@@ -127,8 +91,7 @@
 		};
 
 		display-timings {
-			hsd100pxn1 {
-				u-boot,panel-name = "hannstar,hsd100pxn1";
+			timing-hsd100pxn1 {
 				clock-frequency = <65000000>;
 				hactive = <1024>;
 				vactive = <768>;
@@ -142,7 +105,7 @@
 				pixelclk-active = <1>;
 			};
 
-			VGA {
+			timing-vga {
 				clock-frequency = <25200000>;
 				hactive = <640>;
 				vactive = <480>;
@@ -158,8 +121,7 @@
 				pixelclk-active = <0>;
 			};
 
-			nl12880bc20 {
-				u-boot,panel-name = "nlt,nl12880bc20-spwg-24";
+			timing-nl12880bc20 {
 				clock-frequency = <71000000>;
 				hactive = <1280>;
 				vactive = <800>;
@@ -175,8 +137,7 @@
 				pixelclk-active = <1>;
 			};
 
-			ET0700 {
-				u-boot,panel-name = "edt,etm0700g0dh6";
+			timing-et0700 {
 				clock-frequency = <33264000>;
 				hactive = <800>;
 				vactive = <480>;
@@ -192,8 +153,7 @@
 				pixelclk-active = <0>;
 			};
 
-			ETV570 {
-				u-boot,panel-name = "edt,et057090dhu";
+			timing-etv570 {
 				clock-frequency = <25200000>;
 				hactive = <640>;
 				vactive = <480>;
@@ -224,7 +184,7 @@
 		};
 
 		display-timings {
-			hsd100pxn1 {
+			timing-hsd100pxn1 {
 				clock-frequency = <65000000>;
 				hactive = <1024>;
 				vactive = <768>;
@@ -238,7 +198,7 @@
 				pixelclk-active = <1>;
 			};
 
-			VGA {
+			timing-vga {
 				clock-frequency = <25200000>;
 				hactive = <640>;
 				vactive = <480>;
@@ -254,7 +214,7 @@
 				pixelclk-active = <0>;
 			};
 
-			nl12880bc20 {
+			timing-nl12880bc20 {
 				clock-frequency = <71000000>;
 				hactive = <1280>;
 				vactive = <800>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-tx6-mb7.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-tx6-mb7.dtsi
new file mode 100644
index 000000000000..dd4e5bce4a55
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-tx6-mb7.dtsi
@@ -0,0 +1,58 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
+ */
+
+/ {
+	backlight0 {
+		pwms = <&pwm1 0 500000 PWM_POLARITY_INVERTED>;
+		power-supply = <&reg_lcd1_pwr>;
+	};
+
+	backlight1 {
+		pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
+		power-supply = <&reg_lcd1_pwr>;
+	};
+
+	lcd-panel {
+		compatible = "edt,et057090dhu";
+		pixelclk-active = <0>;
+	};
+
+	lvds0-panel {
+		compatible = "edt,etml1010g0dka";
+		pixelclk-active = <0>;
+	};
+
+	lvds1-panel {
+		compatible = "edt,etml1010g0dka";
+		pixelclk-active = <0>;
+	};
+};
+
+&can1 {
+	status = "disabled";
+};
+
+&can2 {
+	xceiver-supply = <&reg_3v3>;
+};
+
+&ds1339 {
+	/*
+	 * The backup voltage of the module internal RTC is not wired
+	 * by default on the MB7, so disable that RTC chip.
+	 */
+	status = "disabled";
+};
+
+&i2c3 {
+	rtc: rtc@6f {
+		compatible = "microchip,mcp7940x";
+		reg = <0x6f>;
+	};
+};
+
+&reg_lcd0_pwr {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-tx6.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-tx6.dtsi
index bcc5bbcce769..57297d6521cf 100644
--- a/arch/arm/boot/dts/imx6qdl-tx6.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-tx6.dtsi
@@ -1,42 +1,6 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
 /*
  * Copyright 2014-2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 #include <dt-bindings/gpio/gpio.h>
@@ -70,9 +34,8 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		mclk: clock@0 {
+		mclk: clock {
 			compatible = "fixed-clock";
-			reg = <0>;
 			#clock-cells = <0>;
 			clock-frequency = <26000000>;
 		};
@@ -81,7 +44,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power Button";
 			gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_POWER>;
@@ -92,7 +55,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		user_led: user {
+		user_led: led-user {
 			label = "Heartbeat";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_user_led>;
@@ -216,7 +179,7 @@
 &audmux {
 	status = "okay";
 
-	ssi1 {
+	mux-ssi1 {
 		fsl,audmux-port = <0>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_SYN |
@@ -228,7 +191,7 @@
 		>;
 	};
 
-	pins5 {
+	mux-pins5 {
 		fsl,audmux-port = <4>;
 		fsl,port-config = <
 			IMX_AUDMUX_V2_PTCR_SYN
@@ -264,11 +227,6 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet &pinctrl_enet_mdio &pinctrl_etnphy_rst>;
-	clocks = <&clks IMX6QDL_CLK_ENET>,
-		 <&clks IMX6QDL_CLK_ENET>,
-		 <&clks IMX6QDL_CLK_ENET_REF>,
-		 <&clks IMX6QDL_CLK_ENET_REF>;
-	clock-names = "ipg", "ahb", "ptp", "enet_out";
 	phy-mode = "rmii";
 	phy-reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
 	phy-reset-post-delay = <10>;
@@ -378,7 +336,7 @@
 		>;
 	};
 
-	pinctrl_disp0_1: disp0grp-1 {
+	pinctrl_disp0_1: disp0-1-grp {
 		fsl,pins = <
 			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
 			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15       0x10
@@ -411,7 +369,7 @@
 		>;
 	};
 
-	pinctrl_disp0_2: disp0grp-2 {
+	pinctrl_disp0_2: disp0-2-grp {
 		fsl,pins = <
 			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
 			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15       0x10
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-udoo.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-udoo.dtsi
new file mode 100644
index 000000000000..2be7dc4a9781
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-udoo.dtsi
@@ -0,0 +1,316 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * Author: Fabio Estevam <fabio.estevam@freescale.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	aliases {
+		backlight = &backlight;
+		panelchan = &panelchan;
+		panel7 = &panel7;
+		touchscreenp7 = &touchscreenp7;
+	};
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	backlight: backlight {
+		compatible = "gpio-backlight";
+		gpios = <&gpio1 4 0>;
+		default-on;
+		status = "disabled";
+	};
+
+	gpio-poweroff {
+		compatible = "gpio-poweroff";
+		gpios = <&gpio2 4 0>;
+		pinctrl-0 = <&pinctrl_power_off>;
+		pinctrl-names = "default";
+	};
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x40000000>;
+	};
+
+	panel7: panel7 {
+		/*
+		 * in reality it is a -20t (parallel) model,
+		 * but with LVDS bridge chip attached,
+		 * so it is equivalent to -19t model in drive
+		 * characteristics
+		 */
+		compatible = "urt,umsh-8596md-19t";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_panel>;
+		power-supply = <&reg_panel>;
+		backlight = <&backlight>;
+		status = "disabled";
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+
+	reg_panel: regulator-panel {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd_panel";
+		enable-active-high;
+		gpio = <&gpio1 2 0>;
+	};
+
+	sound {
+		compatible = "fsl,imx6q-udoo-ac97",
+			     "fsl,imx-audio-ac97";
+		model = "fsl,imx6q-udoo-ac97";
+		audio-cpu = <&ssi1>;
+		audio-routing =
+			"RX", "Mic Jack",
+			"Headphone Jack", "TX";
+		mux-int-port = <1>;
+		mux-ext-port = <6>;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c2>;
+	status = "okay";
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	touchscreenp7: touchscreenp7@55 {
+		compatible = "sitronix,st1232";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touchscreenp7>;
+		reg = <0x55>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <13 8>;
+		gpios = <&gpio1 15 0>;
+		status = "disabled";
+	};
+};
+
+&iomuxc {
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL		0x4001f8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001f8b1
+		>;
+	};
+
+	pinctrl_panel: panelgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x70
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x70
+		>;
+	};
+
+	pinctrl_power_off: poweroffgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D4__GPIO2_IO04		0x30
+		>;
+	};
+
+	pinctrl_touchscreenp7: touchscreenp7grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_DAT0__GPIO1_IO15		0x70
+			MX6QDL_PAD_SD2_DAT2__GPIO1_IO13		0x1b0b0
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D26__UART2_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D27__UART2_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA	0x1b0b1
+			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbh: usbhgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x80000000
+			MX6QDL_PAD_NANDF_CS2__CCM_CLKO2 0x130b0
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+			MX6QDL_PAD_EIM_D22__USB_OTG_PWR 0x17059
+			MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x17059
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+			MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x1b0b0
+		>;
+	};
+
+	pinctrl_ac97_running: ac97runninggrp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_PIN2__AUD6_TXD		0x1b0b0
+			MX6QDL_PAD_DI0_PIN3__AUD6_TXFS		0x1b0b0
+			MX6QDL_PAD_DI0_PIN4__AUD6_RXD		0x13080
+			MX6QDL_PAD_DI0_PIN15__AUD6_TXC		0x13080
+			MX6QDL_PAD_EIM_EB2__GPIO2_IO30		0x1b0b0
+		>;
+	};
+
+	pinctrl_ac97_warm_reset: ac97warmresetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_PIN2__AUD6_TXD		0x1b0b0
+			MX6QDL_PAD_DI0_PIN3__GPIO4_IO19		0x1b0b0
+			MX6QDL_PAD_DI0_PIN4__AUD6_RXD		0x13080
+			MX6QDL_PAD_DI0_PIN15__AUD6_TXC		0x13080
+			MX6QDL_PAD_EIM_EB2__GPIO2_IO30		0x1b0b0
+		>;
+	};
+
+	pinctrl_ac97_reset: ac97resetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_PIN2__GPIO4_IO18		0x1b0b0
+			MX6QDL_PAD_DI0_PIN3__GPIO4_IO19		0x1b0b0
+			MX6QDL_PAD_DI0_PIN4__AUD6_RXD		0x13080
+			MX6QDL_PAD_DI0_PIN15__AUD6_TXC		0x13080
+			MX6QDL_PAD_EIM_EB2__GPIO2_IO30		0x1b0b0
+		>;
+	};
+};
+
+&ldb {
+	status = "okay";
+
+	panelchan: lvds-channel@0 {
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usbh1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbh>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	usb-port@1 {
+		compatible = "usb424,2514";
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&clks IMX6QDL_CLK_CKO>;
+		reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&audmux {
+	status = "okay";
+};
+
+&ssi1 {
+	cell-index = <0>;
+	fsl,mode = "ac97-slave";
+	pinctrl-names = "ac97-running", "ac97-reset", "ac97-warm-reset";
+	pinctrl-0 = <&pinctrl_ac97_running>;
+	pinctrl-1 = <&pinctrl_ac97_reset>;
+	pinctrl-2 = <&pinctrl_ac97_warm_reset>;
+	ac97-gpios = <&gpio4 19 0 &gpio4 18 0 &gpio2 30 0>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-var-dart.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-var-dart.dtsi
index c41cac502bac..7749074e438d 100644
--- a/arch/arm/boot/dts/imx6qdl-var-dart.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-var-dart.dtsi
@@ -39,7 +39,7 @@
 	pinctrl-0 = <&pinctrl_audmux>;
 	status = "okay";
 
-	ssi2 {
+	mux-ssi2 {
 		fsl,audmux-port = <1>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_SYN |
@@ -51,7 +51,7 @@
 		>;
 	};
 
-	aud3 {
+	mux-aud3 {
 		fsl,audmux-port = <2>;
 		fsl,port-config = <
 			IMX_AUDMUX_V2_PTCR_SYN
@@ -194,7 +194,7 @@
 };
 
 &iomuxc {
-	pinctrl_audmux: audmux {
+	pinctrl_audmux: audmuxgrp {
 		fsl,pins = <
 			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
 			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
@@ -205,7 +205,7 @@
 		>;
 	};
 
-	pinctrl_bt: bt {
+	pinctrl_bt: btgrp {
 		fsl,pins = <
 			/* Bluetooth enable */
 			MX6QDL_PAD_SD3_DAT6__GPIO6_IO18		0x1b0b1
@@ -346,7 +346,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+	pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD1_CMD__SD1_CMD	0x170B9
 			MX6QDL_PAD_SD1_CLK__SD1_CLK	0x100B9
@@ -357,7 +357,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+	pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD1_CMD__SD1_CMD	0x170F9
 			MX6QDL_PAD_SD1_CLK__SD1_CLK	0x100F9
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-var-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-var-som.dtsi
new file mode 100644
index 000000000000..2bff5f92242a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-var-som.dtsi
@@ -0,0 +1,569 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Support for Variscite VAR-SOM-MX6 Module
+ *
+ * Copyright 2011 Linaro Ltd.
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright (C) 2014-2016 Variscite, Ltd.
+ * Author: Donio Ron <ron.d@variscite.com>
+ * Copyright 2022 Bootlin
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include <dt-bindings/clock/imx6qdl-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+	model = "Variscite VAR-SOM-MX6 module";
+	compatible = "variscite,var-som-imx6q", "fsl,imx6q";
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x40000000>;
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_usb_h1_vbus: regulator-usb-h1-vbud {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_wl18xx_vmmc: regulator-wl18xx {
+		compatible = "regulator-fixed";
+		regulator-name = "vwl1807";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio7 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <70000>;
+	};
+
+	sound: sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "var-som-audio";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&sound_codec>;
+		simple-audio-card,frame-master = <&sound_codec>;
+		simple-audio-card,widgets = "Headphone", "Headphone Jack",
+					    "Line", "Line In", "Microphone", "Mic Jack";
+		simple-audio-card,routing = "Headphone Jack", "HPLOUT",
+					    "Headphone Jack", "HPROUT",
+					    "LINE1L", "Line In",
+					    "LINE1R", "Line In";
+
+		sound_cpu: simple-audio-card,cpu {
+			sound-dai = <&ssi2>;
+		};
+
+		sound_codec: simple-audio-card,codec {
+			sound-dai = <&tlv320aic3106>;
+			clocks = <&clks IMX6QDL_CLK_CKO>;
+		};
+	};
+
+	rfkill {
+		compatible = "rfkill-gpio";
+		name = "rfkill";
+		radio-type = "bluetooth";
+		shutdown-gpios = <&gpio6 18 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+
+	mux-ssi2 {
+		fsl,audmux-port = <1>;
+		fsl,port-config = <
+			(IMX_AUDMUX_V2_PTCR_SYN |
+			IMX_AUDMUX_V2_PTCR_TFSDIR |
+			IMX_AUDMUX_V2_PTCR_TFSEL(2) |
+			IMX_AUDMUX_V2_PTCR_TCLKDIR |
+			IMX_AUDMUX_V2_PTCR_TCSEL(2))
+			IMX_AUDMUX_V2_PDCR_RXDSEL(2)
+		>;
+	};
+
+	mux-aud3 {
+		fsl,audmux-port = <2>;
+		fsl,port-config = <
+			IMX_AUDMUX_V2_PTCR_SYN
+			IMX_AUDMUX_V2_PDCR_RXDSEL(1)
+		>;
+	};
+};
+
+&ecspi3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3>;
+	cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii";
+	phy-handle = <&rgmii_phy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rgmii_phy: ethernet-phy@7 {
+			reg = <7>;
+			reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+		};
+	};
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	status = "okay";
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	pmic@8 {
+		compatible = "fsl,pfuze100";
+		reg = <0x08>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+
+		regulators {
+			sw1a_reg: sw1ab {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw1c_reg: sw1c {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3a_reg: sw3a {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3950000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3b_reg: sw3b {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3950000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw4_reg: sw4 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3950000>;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vgen1 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen2_reg: vgen2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen3_reg: vgen3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vgen4_reg: vgen4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vgen5_reg: vgen5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vgen6_reg: vgen6 {
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+		};
+	};
+
+	tlv320aic3106: audio-codec@1b {
+		compatible = "ti,tlv320aic3106";
+		reg = <0x1b>;
+		#sound-dai-cells = <0>;
+		DRVDD-supply = <&reg_3p3v>;
+		AVDD-supply = <&reg_3p3v>;
+		IOVDD-supply = <&reg_3p3v>;
+		DVDD-supply = <&reg_1p8v>;
+		ai3x-ocmv = <0>;
+		reset-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>;
+		ai3x-gpio-func = <
+			0 /* AIC3X_GPIO1_FUNC_DISABLED */
+			5 /* AIC3X_GPIO2_FUNC_DIGITAL_MIC_INPUT */
+		>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
+			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
+			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
+			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
+			/* Audio Clock */
+			MX6QDL_PAD_GPIO_0__CCM_CLKO1		0x130b0
+		>;
+	};
+
+	pinctrl_bt: btgrp {
+		fsl,pins = <
+			/* Bluetooth/wifi enable */
+			MX6QDL_PAD_SD3_DAT6__GPIO6_IO18		0x1b0b1
+			/* Wifi Slow Clock */
+			MX6QDL_PAD_ENET_RXD0__OSC32K_32K_OUT	0x000b0
+		>;
+	};
+
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO	0x100b1
+			MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI	0x100b1
+			MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK	0x100b1
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b0b0
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b0b0
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b0b0
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b0b0
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b0b0
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b0b0
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b0b0
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b0b0
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b0b0
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b0b0
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b0b0
+		>;
+	};
+
+	pinctrl_enet_irq: enetirqgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_6__ENET_IRQ	0x000b1
+		>;
+	};
+
+	pinctrl_gpmi_nand: gpminandgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CLE__NAND_CLE		0xb0b1
+			MX6QDL_PAD_NANDF_ALE__NAND_ALE		0xb0b1
+			MX6QDL_PAD_NANDF_CS0__NAND_CE0_B	0xb0b1
+			MX6QDL_PAD_NANDF_CS1__NAND_CE1_B	0xb0b1
+			MX6QDL_PAD_NANDF_RB0__NAND_READY_B	0xb0b1
+			MX6QDL_PAD_NANDF_D0__NAND_DATA00	0xb0b1
+			MX6QDL_PAD_NANDF_D1__NAND_DATA01	0xb0b1
+			MX6QDL_PAD_NANDF_D2__NAND_DATA02	0xb0b1
+			MX6QDL_PAD_NANDF_D3__NAND_DATA03	0xb0b1
+			MX6QDL_PAD_NANDF_D4__NAND_DATA04	0xb0b1
+			MX6QDL_PAD_NANDF_D5__NAND_DATA05	0xb0b1
+			MX6QDL_PAD_NANDF_D6__NAND_DATA06	0xb0b1
+			MX6QDL_PAD_NANDF_D7__NAND_DATA07	0xb0b1
+			MX6QDL_PAD_SD4_CMD__NAND_RE_B		0xb0b1
+			MX6QDL_PAD_SD4_CLK__NAND_WE_B		0xb0b1
+			MX6QDL_PAD_NANDF_WP_B__NAND_WP_B	0xb0b1
+		>;
+	};
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			/* CTW6120 IRQ */
+			MX6QDL_PAD_EIM_DA7__GPIO3_IO07		0xb0b1
+			/* SDMMC2 CD/WP */
+			MX6QDL_PAD_KEY_COL4__GPIO4_IO14		0x1b0b0
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA	0x4001b8b1
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL	0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL	0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA	0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL	0x4001b8b1
+			MX6QDL_PAD_GPIO_16__I2C3_SDA	0x4001b8b1
+		>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			/* PMIC INT */
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12	0x1b0b0
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT9__PWM2_OUT	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT4__UART2_RX_DATA	0x1b0b1
+			MX6QDL_PAD_SD3_DAT5__UART2_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D28__UART2_CTS_B		0x1b0b1
+			MX6QDL_PAD_EIM_D29__UART2_RTS_B		0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD	0x17069
+			MX6QDL_PAD_SD3_CLK__SD3_CLK	0x10069
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0	0x17069
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1	0x17069
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2	0x17069
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3	0x17069
+			/* WL_EN */
+			MX6QDL_PAD_SD3_DAT7__GPIO6_IO17 0x13059
+			/* WL_IRQ */
+			MX6QDL_PAD_SD3_RST__GPIO7_IO08  0x13059
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhz-grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD	0x170B9
+			MX6QDL_PAD_SD3_CLK__SD3_CLK	0x100B9
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0	0x170B9
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1	0x170B9
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3	0x170B9
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3	0x170B9
+			/* WL_EN */
+			MX6QDL_PAD_SD3_DAT7__GPIO6_IO17 0x130B9
+			/* WL_IRQ */
+			MX6QDL_PAD_SD3_RST__GPIO7_IO08  0x130B9
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhz-grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD	0x170F9
+			MX6QDL_PAD_SD3_CLK__SD3_CLK	0x100F9
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0	0x170F9
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1	0x170F9
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2	0x170F9
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3	0x170F9
+			/* WL_EN */
+			MX6QDL_PAD_SD3_DAT7__GPIO6_IO17 0x130F9
+			/* WL_IRQ */
+			MX6QDL_PAD_SD3_RST__GPIO7_IO08  0x130F9
+		>;
+	};
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "okay";
+};
+
+&reg_arm {
+	vin-supply = <&sw1a_reg>;
+};
+
+&reg_pu {
+	vin-supply = <&sw1c_reg>;
+};
+
+&reg_soc {
+	vin-supply = <&sw1c_reg>;
+};
+
+&reg_vdd1p1 {
+	vin-supply = <&vgen5_reg>;
+};
+
+&reg_vdd2p5 {
+	vin-supply = <&vgen5_reg>;
+};
+
+&snvs_poweroff {
+	status = "okay";
+};
+
+&ssi2 {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2 &pinctrl_bt>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usb_h1_vbus>;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg_var>;
+	disable-over-current;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbphy1 {
+	fsl,tx-d-cal = <106>;
+};
+
+&usbphy2 {
+	fsl,tx-d-cal = <106>;
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	non-removable;
+	keep-power-in-suspend;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_wl18xx_vmmc>;
+	non-removable;
+	wakeup-source;
+	keep-power-in-suspend;
+	cap-power-off-card;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	wifi: wifi@2 {
+		compatible = "ti,wl1835";
+		reg = <2>;
+		interrupt-parent = <&gpio6>;
+		interrupts = <17 IRQ_TYPE_EDGE_RISING>;
+		ref-clock-frequency = <38400000>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-vicut1-12inch.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-vicut1-12inch.dtsi
new file mode 100644
index 000000000000..73f381e14467
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-vicut1-12inch.dtsi
@@ -0,0 +1,128 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2021 Protonic Holland
+ */
+
+/ {
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpiokeys>;
+		autorepeat;
+
+		power-button {
+			label = "Power Button";
+			gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+	};
+
+	panel {
+		compatible = "kyo,tcg121xglp";
+		backlight = <&backlight_lcd>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&rgmii_phy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Microchip KSZ9031RNX PHY */
+		rgmii_phy: ethernet-phy@0 {
+			reg = <0>;
+			interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
+			"CAM2_MIRROR", "", "", "SMBALERT",
+		"DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
+		"SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
+			"SD1_DATA3", "ETH_MDIO", "",
+		"", "ETH_RESET", "", "", "ETH_INT", "", "", "ETH_MDC";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
+		"UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
+			"CAN2_SR", "CAN2_TX", "CAN2_RX",
+		"", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
+			"HITCH_IN_OUT",
+		"LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
+			"ISB_LED";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
+			"I2S_BITCLK", "I2S_DOUT",
+		"I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
+			"YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
+};
+
+&gpio6 {
+	gpio-line-names =
+		"ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
+			"ITU656_D6", "ITU656_D7", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2",
+			"RGMII_TD3",
+		"RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1",
+			"RGMII_RD2", "RGMII_RD3", "", "";
+};
+
+&iomuxc {
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC			0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0			0x1b030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1			0x1b030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2			0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3			0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL		0x1b030
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC			0x10030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0			0x10030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1			0x10030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2			0x10030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3			0x10030
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL		0x10030
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK		0x10030
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO			0x10030
+			MX6QDL_PAD_ENET_MDC__ENET_MDC			0x10030
+			/* Phy reset */
+			MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25		0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28		0x1b0b1
+		>;
+	};
+
+	pinctrl_gpiokeys: gpiokeygrp {
+		fsl,pins = <
+			/* nON_SWITCH */
+			MX6QDL_PAD_EIM_CS0__GPIO2_IO23			0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-vicut1.dtsi
index 1ac7e13249d2..de2b12dad7d8 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-vicut1.dtsi
@@ -16,18 +16,37 @@
 		stdout-path = &uart4;
 	};
 
-	backlight: backlight {
+	backlight_lcd: backlight {
 		compatible = "pwm-backlight";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_backlight>;
 		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 16 64 255>;
 		num-interpolated-steps = <16>;
-		default-brightness-level = <1>;
+		default-brightness-level = <48>;
 		power-supply = <&reg_3v3>;
 		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
 
+	backlight_led: backlight-led {
+		compatible = "pwm-backlight";
+		pwms = <&pwm3 0 5000000 0>;
+		brightness-levels = <0 16 64 255>;
+		num-interpolated-steps = <16>;
+		default-brightness-level = <48>;
+		power-supply = <&reg_3v3>;
+	};
+
+	/* only for backwards compatibility with old HW */
+	backlight_isb: backlight-isb {
+		compatible = "pwm-backlight";
+		pwms = <&pwm2 0 5000000 0>;
+		brightness-levels = <0 8 48 255>;
+		num-interpolated-steps = <5>;
+		default-brightness-level = <0>;
+		power-supply = <&reg_3v3>;
+	};
+
 	connector {
 		compatible = "composite-video-connector";
 		label = "Composite0";
@@ -61,54 +80,37 @@
 		gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
 	};
 
-	gpio-keys {
-		compatible = "gpio-keys";
-		autorepeat;
-
-		power {
-			label = "Power Button";
-			gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_POWER>;
-			wakeup-source;
-		};
-	};
-
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_leds>;
 
 		led-0 {
-			label = "LED_DI0_DEBUG_0";
+			label = "debug0";
 			function = LED_FUNCTION_HEARTBEAT;
-			gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 
 		led-1 {
-			label = "LED_DI0_DEBUG_1";
+			label = "debug1";
 			function = LED_FUNCTION_DISK;
-			gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
+			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "disk-activity";
 		};
 
 		led-2 {
-			label = "POWER_LED";
+			label = "power_led";
 			function = LED_FUNCTION_POWER;
 			gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 		};
-	};
 
-	panel {
-		compatible = "kyo,tcg121xglp";
-		backlight = <&backlight>;
-		power-supply = <&reg_3v3>;
-
-		port {
-			panel_in: endpoint {
-				remote-endpoint = <&lvds0_out>;
-			};
+		led-3 {
+			label = "isb_led";
+			function = LED_FUNCTION_POWER;
+			gpios = <&gpio4 31 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
 		};
 	};
 
@@ -135,18 +137,6 @@
 		enable-active-high;
 	};
 
-	reg_wifi: regulator-wifi {
-		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_wifi_npd>;
-		regulator-name = "wifi";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-		startup-delay-us = <70000>;
-	};
-
 	sound {
 		compatible = "simple-audio-card";
 		simple-audio-card,name = "prti6q-sgtl5000";
@@ -173,6 +163,22 @@
 			frame-master;
 		};
 	};
+
+	thermal-zones {
+		chassis-thermal {
+			polling-delay = <20000>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&tsens0>;
+
+			trips {
+				alert {
+					temperature = <105000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+			};
+		};
+	};
 };
 
 &audmux {
@@ -232,47 +238,13 @@
 	};
 };
 
-&fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii-id";
-	phy-handle = <&rgmii_phy>;
-	status = "okay";
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		/* Microchip KSZ9031RNX PHY */
-		rgmii_phy: ethernet-phy@0 {
-			reg = <0>;
-			interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
-			reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
-			reset-assert-us = <10000>;
-			reset-deassert-us = <300>;
-		};
-	};
-};
-
-&gpio1 {
-	gpio-line-names =
-		"CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
-			"CAM2_MIRROR", "", "", "SMBALERT",
-		"DEBUG_0", "DEBUG_1", "SDIO_SCK", "SDIO_CMD", "SDIO_D3",
-			"SDIO_D2", "SDIO_D1", "SDIO_D0",
-		"SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
-			"SD1_DATA3", "", "",
-		"", "ETH_RESET", "WIFI_PD", "WIFI_BT_RST", "ETH_INT", "",
-			"WL_IRQ", "ETH_MDC";
-};
-
 &gpio2 {
 	gpio-line-names =
-		"count0", "count1", "count2", "", "", "", "", "",
-		"REV_ID0", "REV_ID1", "REV_ID2", "REV_ID3", "REV_ID4",
-			"BOARD_ID0", "BOARD_ID1", "BOARD_ID2",
-		"", "", "", "", "", "", "", "ON_SWITCH",
-		"POWER_LED", "", "ECSPI2_SS0", "", "", "", "", "";
+		"YACO_WHEEL", "YACO_RADAR", "YACO_PTO", "", "", "", "", "",
+		"", "LED_PWM", "", "", "",
+			"", "", "",
+		"", "", "", "", "", "ISB_IN2", "ISB_nIN1", "ON_SWITCH",
+		"POWER_LED", "", "", "", "", "", "", "";
 };
 
 &gpio3 {
@@ -281,37 +253,8 @@
 		"", "", "", "", "", "", "", "",
 		"ECSPI1_SCLK", "ECSPI1_MISO", "ECSPI1_MOSI", "ECSPI1_SS1",
 			"CPU_ON1_FB", "USB_OTG_OC", "USB_OTG_PWR", "YACO_IRQ",
-		"", "", "", "", "", "", "", "";
-};
-
-&gpio4 {
-	gpio-line-names =
-		"", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
-		"UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
-			"CAN2_SR", "CAN2_TX", "CAN2_RX",
-		"LED_DI0_DEBUG_0", "LED_DI0_DEBUG_1", "", "", "", "", "", "",
-		"", "", "", "", "BL_EN", "BL_PWM", "", "";
-};
-
-&gpio5 {
-	gpio-line-names =
-		"", "", "", "", "", "PCIE_WAKE", "PCIE_CLKREQ", "PCIE_W_DIS",
-		"PCIE_RESET", "", "", "", "", "", "", "",
-		"", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
-			"I2S_BITCLK", "I2S_DOUT",
-		"I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
-			"YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
-};
-
-&gpio6 {
-	gpio-line-names =
-		"ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
-			"ITU656_D6", "ITU656_D7", "", "",
-		"", "", "", "", "", "", "", "",
-		"", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2",
-			"RGMII_TD3",
-		"RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1",
-			"RGMII_RD2", "RGMII_RD3", "", "";
+		"TSS_TXD", "TSS_RXD", "", "", "", "", "YACO_BOOT0",
+			"YACO_RESET";
 };
 
 &gpio7 {
@@ -406,9 +349,10 @@
 		reg = <0x51>;
 	};
 
-	temperature-sensor@70 {
+	tsens0: temperature-sensor@70 {
 		compatible = "ti,tmp103";
 		reg = <0x70>;
+		#thermal-sensor-cells = <0>;
 	};
 };
 
@@ -438,31 +382,31 @@
 	};
 };
 
-&pcie {
-	status = "okay";
-};
-
 &pwm1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
 };
 
-&ssi1 {
-	#sound-dai-cells = <0>;
-	fsl,mode = "ac97-slave";
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
 	status = "okay";
 };
 
-&uart1 {
+&pwm3 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
+	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "okay";
 };
 
-&uart2 {
+&ssi1 {
+	status = "okay";
+};
+
+&uart1 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
+	pinctrl-0 = <&pinctrl_uart1>;
 	status = "okay";
 };
 
@@ -485,9 +429,9 @@
 };
 
 &usbh1 {
-	pinctrl-names = "default";
 	phy_type = "utmi";
 	dr_mode = "host";
+	disable-over-current;
 	status = "okay";
 };
 
@@ -501,6 +445,14 @@
 	status = "okay";
 };
 
+&usbphynop1 {
+	status = "disabled";
+};
+
+&usbphynop2 {
+	status = "disabled";
+};
+
 &usdhc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc1>;
@@ -513,26 +465,6 @@
 	status = "okay";
 };
 
-&usdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc2>;
-	vmmc-supply = <&reg_wifi>;
-	non-removable;
-	cap-power-off-card;
-	keep-power-in-suspend;
-	no-1-8-v;
-	no-mmc;
-	no-sd;
-	status = "okay";
-
-	wifi {
-		compatible = "ti,wl1271";
-		interrupts-extended = <&gpio1 30 IRQ_TYPE_LEVEL_HIGH>;
-		ref-clock-frequency = "38400000";
-		tcxo-clock-frequency = "19200000";
-	};
-};
-
 &usdhc3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc3>;
@@ -613,29 +545,6 @@
 		>;
 	};
 
-	pinctrl_enet: enetgrp {
-		fsl,pins = <
-			MX6QDL_PAD_RGMII_RXC__RGMII_RXC			0x1b030
-			MX6QDL_PAD_RGMII_RD0__RGMII_RD0			0x1b030
-			MX6QDL_PAD_RGMII_RD1__RGMII_RD1			0x1b030
-			MX6QDL_PAD_RGMII_RD2__RGMII_RD2			0x1b030
-			MX6QDL_PAD_RGMII_RD3__RGMII_RD3			0x1b030
-			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL		0x1b030
-			MX6QDL_PAD_RGMII_TXC__RGMII_TXC			0x10030
-			MX6QDL_PAD_RGMII_TD0__RGMII_TD0			0x10030
-			MX6QDL_PAD_RGMII_TD1__RGMII_TD1			0x10030
-			MX6QDL_PAD_RGMII_TD2__RGMII_TD2			0x10030
-			MX6QDL_PAD_RGMII_TD3__RGMII_TD3			0x10030
-			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL		0x10030
-			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK		0x10030
-			MX6QDL_PAD_ENET_MDIO__ENET_MDIO			0x10030
-			MX6QDL_PAD_ENET_MDC__ENET_MDC			0x10030
-			/* Phy reset */
-			MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25		0x1b0b0
-			MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28		0x1b0b1
-		>;
-	};
-
 	pinctrl_hog: hoggrp {
 		fsl,pins = <
 			/* ITU656_nRESET */
@@ -646,8 +555,6 @@
 			MX6QDL_PAD_GPIO_4__GPIO1_IO04			0x130b0
 			/* CAM_nDETECT */
 			MX6QDL_PAD_GPIO_17__GPIO7_IO12			0x1b0b0
-			/* nON_SWITCH */
-			MX6QDL_PAD_EIM_CS0__GPIO2_IO23			0x1b0b0
 			/* ISB_IN1 */
 			MX6QDL_PAD_EIM_A16__GPIO2_IO22			0x130b0
 			/* ISB_nIN2 */
@@ -669,27 +576,11 @@
 			/* ITU656_nPDN */
 			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20		0x1b0b0
 
-			/* HW revision detect */
-			/* REV_ID0 */
-			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08			0x1b0b0
-			/* REV_ID1 */
-			MX6QDL_PAD_SD4_DAT1__GPIO2_IO09			0x1b0b0
-			/* REV_ID2 */
-			MX6QDL_PAD_SD4_DAT2__GPIO2_IO10			0x1b0b0
-			/* REV_ID3 */
-			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11			0x1b0b0
-			/* REV_ID4 */
-			MX6QDL_PAD_SD4_DAT4__GPIO2_IO12			0x1b0b0
-
 			/* New in HW revision 1 */
 			/* ON1_FB */
 			MX6QDL_PAD_EIM_D20__GPIO3_IO20			0x100b0
 			/* DIP1_FB */
 			MX6QDL_PAD_DI0_PIN2__GPIO4_IO18			0x1b0b0
-
-			/* New in UT2: FIXME: ISB PWM should start off, PD */
-			/* ISB_LED_PWM */
-			MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30		0x130b0
 		>;
 	};
 
@@ -729,6 +620,8 @@
 			MX6QDL_PAD_DI0_PIN15__GPIO4_IO17		0x1b0b0
 			/* POWER_LED */
 			MX6QDL_PAD_EIM_CS1__GPIO2_IO24			0x1b0b0
+			/* ISB_LED */
+			MX6QDL_PAD_DISP0_DAT10__GPIO4_IO31		0x1b0b0
 		>;
 	};
 
@@ -738,20 +631,23 @@
 		>;
 	};
 
-	/* YaCO AUX Uart */
-	pinctrl_uart1: uart1grp {
+	pinctrl_pwm2: pwm2grp {
 		fsl,pins = <
-			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA		0x1b0b1
-			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA		0x1b0b1
+			MX6QDL_PAD_DISP0_DAT9__PWM2_OUT			0x1b0b0
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT1__PWM3_OUT			0x1b0b0
 		>;
 	};
 
-	pinctrl_uart2: uart2grp {
+	/* YaCO AUX Uart */
+	pinctrl_uart1: uart1grp {
 		fsl,pins = <
-			MX6QDL_PAD_EIM_D26__UART2_RX_DATA		0x1b0b1
-			MX6QDL_PAD_EIM_D27__UART2_TX_DATA		0x1b0b1
-			MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B		0x1b0b1
-			MX6QDL_PAD_EIM_D29__UART2_DTE_RTS_B		0x1b0b1
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA		0x1b0b1
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA		0x1b0b1
 		>;
 	};
 
@@ -797,19 +693,6 @@
 		>;
 	};
 
-	pinctrl_usdhc2: usdhc2grp {
-		fsl,pins = <
-			MX6QDL_PAD_SD2_CMD__SD2_CMD			0x170b9
-			MX6QDL_PAD_SD2_CLK__SD2_CLK			0x100b9
-			MX6QDL_PAD_SD2_DAT0__SD2_DATA0			0x170b9
-			MX6QDL_PAD_SD2_DAT1__SD2_DATA1			0x170b9
-			MX6QDL_PAD_SD2_DAT2__SD2_DATA2			0x170b9
-			MX6QDL_PAD_SD2_DAT3__SD2_DATA3			0x170b9
-			/* WL12xx IRQ */
-			MX6QDL_PAD_ENET_TXD0__GPIO1_IO30		0x10880
-		>;
-	};
-
 	pinctrl_usdhc3: usdhc3grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD			0x17099
@@ -825,10 +708,4 @@
 			MX6QDL_PAD_SD3_RST__SD3_RESET			0x1b0b1
 		>;
 	};
-
-	pinctrl_wifi_npd: wifinpdgrp {
-		fsl,pins = <
-			MX6QDL_PAD_ENET_RXD1__GPIO1_IO26		0x1b8b0
-		>;
-	};
 };
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-wandboard-revb1.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-wandboard-revb1.dtsi
new file mode 100644
index 000000000000..3a21ae942273
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-wandboard-revb1.dtsi
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright 2013 Freescale Semiconductor, Inc.
+//
+// Author: Fabio Estevam <fabio.estevam@freescale.com>
+
+#include "imx6qdl-wandboard.dtsi"
+
+&iomuxc {
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x80000000	/* uSDHC1 CD */
+			MX6QDL_PAD_EIM_DA9__GPIO3_IO09		0x80000000	/* uSDHC3 CD */
+			MX6QDL_PAD_EIM_EB1__GPIO2_IO29		0x0f0b0		/* WL_REF_ON */
+			MX6QDL_PAD_EIM_A25__GPIO5_IO02		0x0f0b0		/* WL_RST_N */
+			MX6QDL_PAD_ENET_RXD1__GPIO1_IO26	0x000b0		/* WL_REG_ON */
+			MX6QDL_PAD_ENET_TXD1__GPIO1_IO29	0x80000000	/* WL_HOST_WAKE */
+			MX6QDL_PAD_ENET_TXD0__GPIO1_IO30	0x80000000	/* WL_WAKE */
+			MX6QDL_PAD_EIM_D29__GPIO3_IO29		0x80000000	/* RGMII_nRST */
+			MX6QDL_PAD_EIM_DA13__GPIO3_IO13		0x80000000	/* BT_ON */
+			MX6QDL_PAD_EIM_DA14__GPIO3_IO14		0x80000000	/* BT_WAKE */
+			MX6QDL_PAD_EIM_DA15__GPIO3_IO15		0x80000000	/* BT_HOST_WAKE */
+		>;
+	};
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	non-removable;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-wandboard-revc1.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-wandboard-revc1.dtsi
new file mode 100644
index 000000000000..cc707972f548
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-wandboard-revc1.dtsi
@@ -0,0 +1,33 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright 2013 Freescale Semiconductor, Inc.
+//
+// Author: Fabio Estevam <fabio.estevam@freescale.com>
+
+#include "imx6qdl-wandboard.dtsi"
+
+&iomuxc {
+	pinctrl-0 = <&pinctrl_hog_c1>;
+
+	pinctrl_hog_c1: hogc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x80000000	/* uSDHC1 CD */
+			MX6QDL_PAD_EIM_DA9__GPIO3_IO09		0x80000000	/* uSDHC3 CD */
+			MX6QDL_PAD_CSI0_DAT14__GPIO6_IO00	0x0f0b0		/* WIFI_ON (reset, active low) */
+			MX6QDL_PAD_ENET_RXD1__GPIO1_IO26	0x000b0		/* WL_REG_ON (unused) */
+			MX6QDL_PAD_ENET_TXD1__GPIO1_IO29	0x80000000	/* WL_HOST_WAKE, input */
+			MX6QDL_PAD_CSI0_DAT13__GPIO5_IO31	0x0f0b0		/* GPIO5_IO31 (Wifi Power Enable) */
+			MX6QDL_PAD_ENET_TXD0__GPIO1_IO30	0x80000000	/* WL_WAKE (unused) */
+			MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21	0x80000000	/* BT_ON */
+			MX6QDL_PAD_CSI0_DAT12__GPIO5_IO30	0x80000000	/* BT_WAKE */
+			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20	0x80000000	/* BT_HOST_WAKE */
+			MX6QDL_PAD_EIM_D29__GPIO3_IO29		0x80000000	/* RGMII_nRST */
+		>;
+	};
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-wandboard-revd1.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-wandboard-revd1.dtsi
index bf86b639fdac..8d44e758f1f3 100644
--- a/arch/arm/boot/dts/imx6qdl-wandboard-revd1.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-wandboard-revd1.dtsi
@@ -27,7 +27,7 @@
 	pinctrl-0 = <&pinctrl_i2c3>;
 	status = "okay";
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
 		reg = <0x08>;
 
@@ -137,49 +137,47 @@
 };
 
 &iomuxc {
-	pinctrl-0 = <&pinctrl_hog>;
-
-	imx6qdl-wandboard {
-		pinctrl_hog: hoggrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x80000000	/* USDHC1 CD */
-				MX6QDL_PAD_EIM_DA9__GPIO3_IO09		0x80000000	/* uSDHC3 CD */
-				MX6QDL_PAD_EIM_D29__GPIO3_IO29   	0x1f0b1		/* RGMII PHY reset */
-			>;
-		};
+	pinctrl-0 = <&pinctrl_hog_d1>;
+
+	pinctrl_hog_d1: hoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x80000000	/* USDHC1 CD */
+			MX6QDL_PAD_EIM_DA9__GPIO3_IO09		0x80000000	/* uSDHC3 CD */
+			MX6QDL_PAD_EIM_D29__GPIO3_IO29   	0x1f0b1		/* RGMII PHY reset */
+		>;
+	};
 
-		pinctrl_enet: enetgrp {
-			fsl,pins = <
-				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
-				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
-				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
-				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
-				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
-				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
-				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
-				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
-				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
-				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
-				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
-				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
-				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
-				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
-				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
-			>;
-		};
+	enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
+		>;
+	};
 
-		pinctrl_i2c3: i2c3grp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_5__I2C3_SCL		0x4001b8b1
-				MX6QDL_PAD_GPIO_16__I2C3_SDA		0x4001b8b1
-			>;
-		};
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL		0x4001b8b1
+			MX6QDL_PAD_GPIO_16__I2C3_SDA		0x4001b8b1
+		>;
+	};
 
-		pinctrl_spdif: spdifgrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_19__SPDIF_OUT		0x1b0b0
-			>;
-		};
+	pinctrl_spdif: spdifgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_19__SPDIF_OUT		0x1b0b0
+		>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-wandboard.dtsi
index ec6fba5ee8fd..26489eccd5fb 100644
--- a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-wandboard.dtsi
@@ -26,11 +26,16 @@
 		mux-ext-port = <3>;
 	};
 
+	spdif_out: spdif-out {
+		compatible = "linux,spdif-dit";
+		#sound-dai-cells = <0>;
+	};
+
 	sound-spdif {
 		compatible = "fsl,imx-audio-spdif";
 		model = "imx-spdif";
-		spdif-controller = <&spdif>;
-		spdif-out;
+		audio-cpu = <&spdif>;
+		audio-codec = <&spdif_out>;
 	};
 
 	reg_1p5v: regulator-1p5v {
@@ -119,6 +124,7 @@
 		pinctrl-0 = <&pinctrl_mclk>;
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_3p3v>;
@@ -131,7 +137,6 @@
 		pinctrl-0 = <&pinctrl_ov5645>;
 		reg = <0x3c>;
 		clocks = <&clks IMX6QDL_CLK_CKO2>;
-		clock-names = "xclk";
 		clock-frequency = <24000000>;
 		vdddo-supply = <&reg_1p8v>;
 		vdda-supply = <&reg_2p8v>;
@@ -152,146 +157,143 @@
 &iomuxc {
 	pinctrl-names = "default";
 
-	imx6qdl-wandboard {
-
-		pinctrl_audmux: audmuxgrp {
-			fsl,pins = <
-				MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
-				MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
-				MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
-				MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
-			>;
-		};
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
+			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
+			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
+			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
+		>;
+	};
 
-		pinctrl_enet: enetgrp {
-			fsl,pins = <
-				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
-				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
-				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
-				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
-				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
-				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
-				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
-				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
-				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
-				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
-				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
-				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
-				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
-				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
-				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
-				MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
-			>;
-		};
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
+		>;
+	};
 
-		pinctrl_i2c1: i2c1grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
-				MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
-			>;
-		};
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__I2C1_SCL		0x4001b8b1
+			MX6QDL_PAD_EIM_D28__I2C1_SDA		0x4001b8b1
+		>;
+	};
 
-		pinctrl_i2c1_gpio: i2c1gpiogrp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D21__GPIO3_IO21		0x4001b8b0
-				MX6QDL_PAD_EIM_D28__GPIO3_IO28		0x4001b8b0
-			>;
-		};
+	pinctrl_i2c1_gpio: i2c1gpiogrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__GPIO3_IO21		0x4001b8b0
+			MX6QDL_PAD_EIM_D28__GPIO3_IO28		0x4001b8b0
+		>;
+	};
 
-		pinctrl_i2c2: i2c2grp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
-				MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
-			>;
-		};
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
+		>;
+	};
 
-		pinctrl_i2c2_gpio: i2c2gpiogrp {
-			fsl,pins = <
-				MX6QDL_PAD_KEY_COL3__GPIO4_IO12		0x4001b8b0
-				MX6QDL_PAD_KEY_ROW3__GPIO4_IO13		0x4001b8b0
-			>;
-		};
+	pinctrl_i2c2_gpio: i2c2gpiogrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__GPIO4_IO12		0x4001b8b0
+			MX6QDL_PAD_KEY_ROW3__GPIO4_IO13		0x4001b8b0
+		>;
+	};
 
-		pinctrl_mclk: mclkgrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_0__CCM_CLKO1		0x130b0
-			>;
-		};
+	pinctrl_mclk: mclkgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_0__CCM_CLKO1		0x130b0
+		>;
+	};
 
-		pinctrl_ov5645: ov5645grp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_3__CCM_CLKO2		0x000b0
-				MX6QDL_PAD_GPIO_6__GPIO1_IO06		0x1b0b0
-				MX6QDL_PAD_KEY_COL4__GPIO4_IO14		0x1b0b0
-			>;
-		};
+	pinctrl_ov5645: ov5645grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_3__CCM_CLKO2		0x000b0
+			MX6QDL_PAD_GPIO_6__GPIO1_IO06		0x1b0b0
+			MX6QDL_PAD_KEY_COL4__GPIO4_IO14		0x1b0b0
+		>;
+	};
 
-		pinctrl_spdif: spdifgrp {
-			fsl,pins = <
-				MX6QDL_PAD_ENET_RXD0__SPDIF_OUT		0x1b0b0
-			>;
-		};
+	pinctrl_spdif: spdifgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RXD0__SPDIF_OUT		0x1b0b0
+		>;
+	};
 
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0b1
-				MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0b1
-			>;
-		};
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0b1
+		>;
+	};
 
-		pinctrl_uart3: uart3grp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
-				MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
-				MX6QDL_PAD_EIM_D23__UART3_CTS_B		0x1b0b1
-				MX6QDL_PAD_EIM_EB3__UART3_RTS_B		0x1b0b1
-			>;
-		};
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D23__UART3_CTS_B		0x1b0b1
+			MX6QDL_PAD_EIM_EB3__UART3_RTS_B		0x1b0b1
+		>;
+	};
 
-		pinctrl_usbotg: usbotggrp {
-			fsl,pins = <
-				MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
-			>;
-		};
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID		0x17059
+		>;
+	};
 
-		pinctrl_usbotgvbus: usbotgvbusgrp {
-			fsl,pins = <
-				MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x130b0
-			>;
-		};
+	pinctrl_usbotgvbus: usbotgvbusgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x130b0
+		>;
+	};
 
-		pinctrl_usdhc1: usdhc1grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD1_CMD__SD1_CMD		0x17059
-				MX6QDL_PAD_SD1_CLK__SD1_CLK		0x10059
-				MX6QDL_PAD_SD1_DAT0__SD1_DATA0		0x17059
-				MX6QDL_PAD_SD1_DAT1__SD1_DATA1		0x17059
-				MX6QDL_PAD_SD1_DAT2__SD1_DATA2		0x17059
-				MX6QDL_PAD_SD1_DAT3__SD1_DATA3		0x17059
-			>;
-		};
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD		0x17059
+			MX6QDL_PAD_SD1_CLK__SD1_CLK		0x10059
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0		0x17059
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1		0x17059
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2		0x17059
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3		0x17059
+		>;
+	};
 
-		pinctrl_usdhc2: usdhc2grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
-				MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
-				MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
-				MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
-				MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
-				MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
-			>;
-		};
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+		>;
+	};
 
-		pinctrl_usdhc3: usdhc3grp {
-			fsl,pins = <
-				MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
-				MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
-				MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
-				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
-				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
-				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
-			>;
-		};
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+		>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-zii-rdu2.dtsi
index 525ff62b47f5..9ff183e4e069 100644
--- a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-zii-rdu2.dtsi
@@ -277,7 +277,7 @@
 	pinctrl-0 = <&pinctrl_uart4>;
 	status = "okay";
 
-	rave-sp {
+	mcu {
 		compatible = "zii,rave-sp-rdu2";
 		current-speed = <1000000>;
 		#address-cells = <1>;
@@ -757,7 +757,7 @@
 
 				port@2 {
 					reg = <2>;
-					label = "cpu";
+					phy-mode = "rev-rmii";
 					ethernet = <&fec>;
 
 					fixed-link {
@@ -848,7 +848,7 @@
 	pinctrl-0 = <&pinctrl_audmux>;
 	status = "okay";
 
-	ssi1 {
+	mux-ssi1 {
 		fsl,audmux-port = <0>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_SYN |
@@ -860,7 +860,7 @@
 		>;
 	};
 
-	aud3 {
+	mux-aud3 {
 		fsl,audmux-port = <2>;
 		fsl,port-config = <
 			IMX_AUDMUX_V2_PTCR_SYN
@@ -868,7 +868,7 @@
 		>;
 	};
 
-	ssi2 {
+	mux-ssi2 {
 		fsl,audmux-port = <1>;
 		fsl,port-config = <
 			(IMX_AUDMUX_V2_PTCR_SYN |
@@ -880,7 +880,7 @@
 		>;
 	};
 
-	aud5 {
+	mux-aud5 {
 		fsl,audmux-port = <4>;
 		fsl,port-config = <
 			IMX_AUDMUX_V2_PTCR_SYN
diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi
index d27beb47f9a3..45bcfd7faf9d 100644
--- a/arch/arm/boot/dts/imx6qdl.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi
@@ -143,21 +143,20 @@
 		#phy-cells = <0>;
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
 		interrupt-parent = <&gpc>;
 		ranges;
 
-		dma_apbh: dma-apbh@110000 {
+		dma_apbh: dma-controller@110000 {
 			compatible = "fsl,imx6q-dma-apbh", "fsl,imx28-dma-apbh";
 			reg = <0x00110000 0x2000>;
 			interrupts = <0 13 IRQ_TYPE_LEVEL_HIGH>,
 				     <0 13 IRQ_TYPE_LEVEL_HIGH>,
 				     <0 13 IRQ_TYPE_LEVEL_HIGH>,
 				     <0 13 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3";
 			#dma-cells = <1>;
 			dma-channels = <4>;
 			clocks = <&clks IMX6QDL_CLK_APBH_DMA>;
@@ -290,7 +289,7 @@
 			status = "disabled";
 		};
 
-		bus@2000000 { /* AIPS1 */
+		aips1: bus@2000000 { /* AIPS1 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -398,11 +397,10 @@
 					reg = <0x02024000 0x4000>;
 					interrupts = <0 51 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6QDL_CLK_ESAI_IPG>,
-						 <&clks IMX6QDL_CLK_ESAI_MEM>,
 						 <&clks IMX6QDL_CLK_ESAI_EXTAL>,
 						 <&clks IMX6QDL_CLK_ESAI_IPG>,
 						 <&clks IMX6QDL_CLK_SPBA>;
-					clock-names = "core", "mem", "extal", "fsys", "spba";
+					clock-names = "core", "extal", "fsys", "spba";
 					dmas = <&sdma 23 21 0>, <&sdma 24 21 0>;
 					dma-names = "rx", "tx";
 					status = "disabled";
@@ -476,7 +474,7 @@
 						<&sdma 20 23 1>, <&sdma 21 23 1>, <&sdma 22 23 1>;
 					dma-names = "rxa", "rxb", "rxc",
 							"txa", "txb", "txc";
-					fsl,asrc-rate  = <48000>;
+					fsl,asrc-rate = <48000>;
 					fsl,asrc-width = <16>;
 					status = "okay";
 				};
@@ -713,8 +711,8 @@
 				reg_vdd3p0: regulator-3p0 {
 					compatible = "fsl,anatop-regulator";
 					regulator-name = "vdd3p0";
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <3150000>;
+					regulator-min-microvolt = <2625000>;
+					regulator-max-microvolt = <3400000>;
 					regulator-always-on;
 					anatop-reg-offset = <0x120>;
 					anatop-vol-bit-shift = <8>;
@@ -762,7 +760,7 @@
 					regulator-name = "vddpu";
 					regulator-min-microvolt = <725000>;
 					regulator-max-microvolt = <1450000>;
-					regulator-enable-ramp-delay = <150>;
+					regulator-enable-ramp-delay = <380>;
 					anatop-reg-offset = <0x140>;
 					anatop-vol-bit-shift = <9>;
 					anatop-vol-bit-width = <5>;
@@ -808,6 +806,7 @@
 				reg = <0x020c9000 0x1000>;
 				interrupts = <0 44 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6QDL_CLK_USBPHY1>;
+				phy-3p0-supply = <&reg_vdd3p0>;
 				fsl,anatop = <&anatop>;
 			};
 
@@ -816,6 +815,7 @@
 				reg = <0x020ca000 0x1000>;
 				interrupts = <0 45 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6QDL_CLK_USBPHY2>;
+				phy-3p0-supply = <&reg_vdd3p0>;
 				fsl,anatop = <&anatop>;
 			};
 
@@ -929,7 +929,7 @@
 				interrupts = <0 125 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
-			sdma: sdma@20ec000 {
+			sdma: dma-controller@20ec000 {
 				compatible = "fsl,imx6q-sdma", "fsl,imx35-sdma";
 				reg = <0x020ec000 0x4000>;
 				interrupts = <0 2 IRQ_TYPE_LEVEL_HIGH>;
@@ -941,7 +941,7 @@
 			};
 		};
 
-		bus@2100000 { /* AIPS2 */
+		aips2: bus@2100000 { /* AIPS2 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -1050,9 +1050,11 @@
 				clocks = <&clks IMX6QDL_CLK_ENET>,
 					 <&clks IMX6QDL_CLK_ENET>,
 					 <&clks IMX6QDL_CLK_ENET_REF>,
-					 <&clks IMX6QDL_CLK_ENET_REF>;
-				clock-names = "ipg", "ahb", "ptp", "enet_out";
+					 <&clks IMX6QDL_CLK_ENET_REF_SEL>;
+				clock-names = "ipg", "ahb", "ptp", "enet_clk_ref";
 				fsl,stop-mode = <&gpr 0x34 27>;
+				nvmem-cells = <&fec_mac_addr>;
+				nvmem-cell-names = "mac-address";
 				status = "disabled";
 			};
 
@@ -1157,7 +1159,7 @@
 				status = "disabled";
 			};
 
-			weim: weim@21b8000 {
+			weim: memory-controller@21b8000 {
 				#address-cells = <2>;
 				#size-cells = <1>;
 				compatible = "fsl,imx6q-weim";
@@ -1186,6 +1188,10 @@
 				tempmon_temp_grade: temp-grade@20 {
 					reg = <0x20 4>;
 				};
+
+				fec_mac_addr: mac-addr@88 {
+					reg = <0x88 6>;
+				};
 			};
 
 			tzasc@21d0000 { /* TZASC1 */
diff --git a/arch/arm/boot/dts/imx6qp-mba6b.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-mba6b.dts
index eee2e09d6e94..eee2e09d6e94 100644
--- a/arch/arm/boot/dts/imx6qp-mba6b.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-mba6b.dts
diff --git a/arch/arm/boot/dts/imx6qp-nitrogen6_max.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-nitrogen6_max.dts
index 741d1ed338ca..741d1ed338ca 100644
--- a/arch/arm/boot/dts/imx6qp-nitrogen6_max.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-nitrogen6_max.dts
diff --git a/arch/arm/boot/dts/imx6qp-nitrogen6_som2.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-nitrogen6_som2.dts
index 1593ac86b2a4..1593ac86b2a4 100644
--- a/arch/arm/boot/dts/imx6qp-nitrogen6_som2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-nitrogen6_som2.dts
diff --git a/arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-phytec-mira-rdk-nand.dts
index a18266598d39..a18266598d39 100644
--- a/arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-phytec-mira-rdk-nand.dts
diff --git a/arch/arm/boot/dts/imx6qp-prtwd3.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-prtwd3.dts
index cf6571cc4682..cad985e341a1 100644
--- a/arch/arm/boot/dts/imx6qp-prtwd3.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-prtwd3.dts
@@ -350,7 +350,7 @@
 	pinctrl-0 = <&pinctrl_usbotg>;
 	phy_type = "utmi";
 	dr_mode = "host";
-	disable-over-current;
+	over-current-active-low;
 	status = "okay";
 };
 
@@ -384,7 +384,7 @@
 	#address-cells = <1>;
 	#size-cells = <0>;
 
-	brcmf: bcrmf@1 {
+	brcmf: wifi@1 {
 		reg = <1>;
 		compatible = "brcm,bcm4329-fmac";
 	};
@@ -548,7 +548,7 @@
 		>;
 	};
 
-	pinctrl_wifi_npd: wifinpd {
+	pinctrl_wifi_npd: wifinpdgrp {
 		fsl,pins = <
 			/* WL_REG_ON */
 			MX6QDL_PAD_NANDF_RB0__GPIO6_IO10		0x13069
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qp-sabreauto.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-sabreauto.dts
new file mode 100644
index 000000000000..c5b220aeaefd
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-sabreauto.dts
@@ -0,0 +1,58 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+//
+// Copyright 2016 Freescale Semiconductor, Inc.
+
+/dts-v1/;
+
+#include "imx6qp.dtsi"
+#include "imx6qdl-sabreauto.dtsi"
+
+/ {
+	model = "Freescale i.MX6 Quad Plus SABRE Automotive Board";
+	compatible = "fsl,imx6qp-sabreauto", "fsl,imx6qp";
+};
+
+&i2c2 {
+	max7322: gpio@68 {
+		compatible = "maxim,max7322";
+		reg = <0x68>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+};
+
+&iomuxc {
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL1__ENET_MDIO          0x1b0b0
+			MX6QDL_PAD_KEY_COL2__ENET_MDC           0x1b0b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC         0x1b018
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0         0x1b018
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1         0x1b018
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2         0x1b018
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3         0x1b018
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL   0x1b018
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC         0x1b018
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0         0x1b018
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1         0x1b018
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2         0x1b018
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3         0x1b018
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL   0x1b018
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK        0x4001b0a8
+			MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
+		>;
+	};
+};
+
+&pcie {
+	reset-gpio = <&max7310_c 5 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&vgen3_reg {
+	regulator-always-on;
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qp-sabresd.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-sabresd.dts
new file mode 100644
index 000000000000..792697bd4551
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-sabresd.dts
@@ -0,0 +1,61 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+//
+// Copyright 2016 Freescale Semiconductor, Inc.
+
+/dts-v1/;
+
+#include "imx6qp.dtsi"
+#include "imx6qdl-sabresd.dtsi"
+
+/ {
+	model = "Freescale i.MX6 Quad Plus SABRE Smart Device Board";
+	compatible = "fsl,imx6qp-sabresd", "fsl,imx6qp";
+};
+
+&reg_arm {
+	vin-supply = <&sw2_reg>;
+};
+
+&iomuxc {
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10071
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+			MX6QDL_PAD_NANDF_D4__SD2_DATA4		0x17059
+			MX6QDL_PAD_NANDF_D5__SD2_DATA5		0x17059
+			MX6QDL_PAD_NANDF_D6__SD2_DATA6		0x17059
+			MX6QDL_PAD_NANDF_D7__SD2_DATA7		0x17059
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10071
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4		0x17059
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5		0x17059
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6		0x17059
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7		0x17059
+		>;
+	};
+};
+
+&vgen3_reg {
+	regulator-always-on;
+};
+
+&pcie {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6qp-tqma6b.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qp-tqma6b.dtsi
index bb6ff7c64b27..bb6ff7c64b27 100644
--- a/arch/arm/boot/dts/imx6qp-tqma6b.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-tqma6b.dtsi
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qp-tx6qp-8037-mb7.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-tx6qp-8037-mb7.dts
new file mode 100644
index 000000000000..3183abdd25aa
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-tx6qp-8037-mb7.dts
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
+ */
+
+/dts-v1/;
+#include "imx6qp-tx6qp-8037.dts"
+#include "imx6qdl-tx6-mb7.dtsi"
+
+/ {
+	model = "Ka-Ro electronics TX6Q-8037 Module on MB7 baseboard";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qp-tx6qp-8037.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-tx6qp-8037.dts
new file mode 100644
index 000000000000..174824a8138e
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-tx6qp-8037.dts
@@ -0,0 +1,50 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
+ */
+
+/dts-v1/;
+#include "imx6qp.dtsi"
+#include "imx6qdl-tx6.dtsi"
+#include "imx6qdl-tx6-lcd.dtsi"
+
+/ {
+	model = "Ka-Ro electronics TX6QP-8037 Module";
+	compatible = "karo,imx6qp-tx6qp", "fsl,imx6qp";
+};
+
+&ds1339 {
+	status = "disabled";
+};
+
+&gpmi {
+	status = "disabled";
+};
+
+&ipu2 {
+	status = "disabled";
+};
+
+&usdhc4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	bus-width = <4>;
+	non-removable;
+	no-1-8-v;
+	fsl,wp-controller;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x070b1
+			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x070b1
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x070b1
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x070b1
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x070b1
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x070b1
+			MX6QDL_PAD_NANDF_ALE__SD4_RESET		0x0b0b1
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qp-tx6qp-8137-mb7.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-tx6qp-8137-mb7.dts
new file mode 100644
index 000000000000..31854bc52e76
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-tx6qp-8137-mb7.dts
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
+ */
+
+/dts-v1/;
+#include "imx6qp-tx6qp-8137.dts"
+#include "imx6qdl-tx6-mb7.dtsi"
+
+/ {
+	model = "Ka-Ro electronics TX6Q-8137 Module on MB7 baseboard";
+	compatible = "karo,imx6qp-tx6qp", "fsl,imx6qp";
+};
+
+&ipu2 {
+	status = "disabled";
+};
+
+&sata {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qp-tx6qp-8137.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-tx6qp-8137.dts
new file mode 100644
index 000000000000..dfe1535128fe
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-tx6qp-8137.dts
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2017 Lothar Waßmann <LW@KARO-electronics.de>
+ */
+
+/dts-v1/;
+#include "imx6qp.dtsi"
+#include "imx6qdl-tx6.dtsi"
+#include "imx6qdl-tx6-lvds.dtsi"
+
+/ {
+	model = "Ka-Ro electronics TX6QP-8137 Module";
+	compatible = "karo,imx6qp-tx6qp", "fsl,imx6qp";
+};
+
+&ds1339 {
+	status = "disabled";
+};
+
+&gpmi {
+	status = "disabled";
+};
+
+&ipu2 {
+	status = "disabled";
+};
+
+&sata {
+	status = "okay";
+};
+
+&usdhc4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	bus-width = <4>;
+	non-removable;
+	no-1-8-v;
+	fsl,wp-controller;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x070b1
+			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x070b1
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x070b1
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x070b1
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x070b1
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x070b1
+			MX6QDL_PAD_NANDF_ALE__SD4_RESET		0x0b0b1
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6qp-vicutp.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-vicutp.dts
index 7bad7ca6b12e..49ff145fffe5 100644
--- a/arch/arm/boot/dts/imx6qp-vicutp.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-vicutp.dts
@@ -6,6 +6,7 @@
 /dts-v1/;
 #include "imx6qp.dtsi"
 #include "imx6qdl-vicut1.dtsi"
+#include "imx6qdl-vicut1-12inch.dtsi"
 
 / {
 	model = "Kverneland UT1P Board";
diff --git a/arch/arm/boot/dts/imx6qp-wandboard-revd1.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-wandboard-revd1.dts
index 08d8b78a2096..08d8b78a2096 100644
--- a/arch/arm/boot/dts/imx6qp-wandboard-revd1.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-wandboard-revd1.dts
diff --git a/arch/arm/boot/dts/imx6qp-yapp4-crux-plus.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-yapp4-crux-plus.dts
index cea165f2161a..afaf4a6759d4 100644
--- a/arch/arm/boot/dts/imx6qp-yapp4-crux-plus.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-yapp4-crux-plus.dts
@@ -33,6 +33,10 @@
 	status = "okay";
 };
 
+&reg_pu {
+	regulator-always-on;
+};
+
 &reg_usb_h1_vbus {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qp-yapp4-pegasus-plus.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-yapp4-pegasus-plus.dts
new file mode 100644
index 000000000000..4a961a33bf2d
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-yapp4-pegasus-plus.dts
@@ -0,0 +1,58 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2021 Y Soft Corporation, a.s.
+
+/dts-v1/;
+
+#include "imx6qp.dtsi"
+#include "imx6dl-yapp43-common.dtsi"
+
+/ {
+	model = "Y Soft IOTA Pegasus+ i.MX6QuadPlus board";
+	compatible = "ysoft,imx6qp-yapp4-pegasus-plus", "fsl,imx6qp";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0xf0000000>;
+	};
+};
+
+&gpio_oled {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&leds {
+	status = "okay";
+};
+
+&oled_1305 {
+	status = "okay";
+};
+
+&oled_1309 {
+	status = "okay";
+};
+
+&reg_pu {
+	regulator-always-on;
+};
+
+&reg_usb_h1_vbus {
+	status = "okay";
+};
+
+&touchkeys {
+	status = "okay";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbphy2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6qp-zii-rdu2.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-zii-rdu2.dts
index 57de447c4609..57de447c4609 100644
--- a/arch/arm/boot/dts/imx6qp-zii-rdu2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-zii-rdu2.dts
diff --git a/arch/arm/boot/dts/imx6qp.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qp.dtsi
index 050365513836..fc164991d2ae 100644
--- a/arch/arm/boot/dts/imx6qp.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp.dtsi
@@ -9,12 +9,18 @@
 		ocram2: sram@940000 {
 			compatible = "mmio-sram";
 			reg = <0x00940000 0x20000>;
+			ranges = <0 0x00940000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
 		ocram3: sram@960000 {
 			compatible = "mmio-sram";
 			reg = <0x00960000 0x20000>;
+			ranges = <0 0x00960000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
diff --git a/arch/arm/boot/dts/imx6s-dhcom-drc02.dts b/arch/arm/boot/dts/nxp/imx/imx6s-dhcom-drc02.dts
index 4077b607c29e..e42c274a9014 100644
--- a/arch/arm/boot/dts/imx6s-dhcom-drc02.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6s-dhcom-drc02.dts
@@ -3,7 +3,7 @@
  * Copyright (C) 2021 DH electronics GmbH
  *
  * DHCOM iMX6 variant:
- * DHCM-iMX6S-C0800-R102-F0409-E-CAN2-RTC-I-01D2
+ * DHCM-iMX6S-C080-R102-F0409-E-CAN2-RTC-I-01D2
  * DHCOM PCB number: 493-400 or newer
  * DRC02 PCB number: 568-100 or newer
  */
diff --git a/arch/arm/boot/dts/imx6sl-evk.dts b/arch/arm/boot/dts/nxp/imx/imx6sl-evk.dts
index 25f6f2fb1555..036705b783f4 100644
--- a/arch/arm/boot/dts/imx6sl-evk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sl-evk.dts
@@ -23,7 +23,7 @@
 
 	backlight_display: backlight_display {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
 	};
@@ -33,7 +33,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_led>;
 
-		user {
+		led-user {
 			label = "debug";
 			gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
@@ -108,7 +108,7 @@
 			"IN3R", "AMIC";
 		mux-int-port = <2>;
 		mux-ext-port = <3>;
-		hp-det-gpio = <&gpio4 19 GPIO_ACTIVE_LOW>;
+		hp-det-gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
 	};
 
 	panel {
@@ -137,7 +137,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p32", "jedec,spi-nor";
@@ -160,7 +160,7 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
 		reg = <0x08>;
 
@@ -287,271 +287,269 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hog>;
 
-	imx6sl-evk {
-		pinctrl_hog: hoggrp {
-			fsl,pins = <
-				MX6SL_PAD_KEY_ROW7__GPIO4_IO07    0x17059
-				MX6SL_PAD_KEY_COL7__GPIO4_IO06    0x17059
-				MX6SL_PAD_SD2_DAT7__GPIO5_IO00    0x17059
-				MX6SL_PAD_SD2_DAT6__GPIO4_IO29    0x17059
-				MX6SL_PAD_REF_CLK_32K__GPIO3_IO22 0x17059
-				MX6SL_PAD_KEY_COL4__GPIO4_IO00	0x80000000
-				MX6SL_PAD_KEY_COL5__GPIO4_IO02	0x80000000
-				MX6SL_PAD_AUD_MCLK__AUDIO_CLK_OUT 0x4130b0
-			>;
-		};
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX6SL_PAD_KEY_ROW7__GPIO4_IO07    0x17059
+			MX6SL_PAD_KEY_COL7__GPIO4_IO06    0x17059
+			MX6SL_PAD_SD2_DAT7__GPIO5_IO00    0x17059
+			MX6SL_PAD_SD2_DAT6__GPIO4_IO29    0x17059
+			MX6SL_PAD_REF_CLK_32K__GPIO3_IO22 0x17059
+			MX6SL_PAD_KEY_COL4__GPIO4_IO00	0x80000000
+			MX6SL_PAD_KEY_COL5__GPIO4_IO02	0x80000000
+			MX6SL_PAD_AUD_MCLK__AUDIO_CLK_OUT 0x4130b0
+		>;
+	};
 
-		pinctrl_audmux3: audmux3grp {
-			fsl,pins = <
-				MX6SL_PAD_AUD_RXD__AUD3_RXD	  0x4130b0
-				MX6SL_PAD_AUD_TXC__AUD3_TXC	  0x4130b0
-				MX6SL_PAD_AUD_TXD__AUD3_TXD	  0x4110b0
-				MX6SL_PAD_AUD_TXFS__AUD3_TXFS	  0x4130b0
-			>;
-		};
+	pinctrl_audmux3: audmux3grp {
+		fsl,pins = <
+			MX6SL_PAD_AUD_RXD__AUD3_RXD	  0x4130b0
+			MX6SL_PAD_AUD_TXC__AUD3_TXC	  0x4130b0
+			MX6SL_PAD_AUD_TXD__AUD3_TXD	  0x4110b0
+			MX6SL_PAD_AUD_TXFS__AUD3_TXFS	  0x4130b0
+		>;
+	};
 
-		pinctrl_ecspi1: ecspi1grp {
-			fsl,pins = <
-				MX6SL_PAD_ECSPI1_MISO__ECSPI1_MISO	0x100b1
-				MX6SL_PAD_ECSPI1_MOSI__ECSPI1_MOSI	0x100b1
-				MX6SL_PAD_ECSPI1_SCLK__ECSPI1_SCLK	0x100b1
-				MX6SL_PAD_ECSPI1_SS0__GPIO4_IO11	0x80000000
-			>;
-		};
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6SL_PAD_ECSPI1_MISO__ECSPI1_MISO	0x100b1
+			MX6SL_PAD_ECSPI1_MOSI__ECSPI1_MOSI	0x100b1
+			MX6SL_PAD_ECSPI1_SCLK__ECSPI1_SCLK	0x100b1
+			MX6SL_PAD_ECSPI1_SS0__GPIO4_IO11	0x80000000
+		>;
+	};
 
-		pinctrl_fec: fecgrp {
-			fsl,pins = <
-				MX6SL_PAD_FEC_MDC__FEC_MDC		0x1b0b0
-				MX6SL_PAD_FEC_MDIO__FEC_MDIO		0x1b0b0
-				MX6SL_PAD_FEC_CRS_DV__FEC_RX_DV		0x1b0b0
-				MX6SL_PAD_FEC_RXD0__FEC_RX_DATA0	0x1b0b0
-				MX6SL_PAD_FEC_RXD1__FEC_RX_DATA1	0x1b0b0
-				MX6SL_PAD_FEC_TX_EN__FEC_TX_EN		0x1b0b0
-				MX6SL_PAD_FEC_TXD0__FEC_TX_DATA0	0x1b0b0
-				MX6SL_PAD_FEC_TXD1__FEC_TX_DATA1	0x1b0b0
-				MX6SL_PAD_FEC_REF_CLK__FEC_REF_OUT	0x4001b0a8
-			>;
-		};
+	pinctrl_fec: fecgrp {
+		fsl,pins = <
+			MX6SL_PAD_FEC_MDC__FEC_MDC		0x1b0b0
+			MX6SL_PAD_FEC_MDIO__FEC_MDIO		0x1b0b0
+			MX6SL_PAD_FEC_CRS_DV__FEC_RX_DV		0x1b0b0
+			MX6SL_PAD_FEC_RXD0__FEC_RX_DATA0	0x1b0b0
+			MX6SL_PAD_FEC_RXD1__FEC_RX_DATA1	0x1b0b0
+			MX6SL_PAD_FEC_TX_EN__FEC_TX_EN		0x1b0b0
+			MX6SL_PAD_FEC_TXD0__FEC_TX_DATA0	0x1b0b0
+			MX6SL_PAD_FEC_TXD1__FEC_TX_DATA1	0x1b0b0
+			MX6SL_PAD_FEC_REF_CLK__FEC_REF_OUT	0x4001b0a8
+		>;
+	};
 
-		pinctrl_fec_sleep: fecgrp-sleep {
-			fsl,pins = <
-				MX6SL_PAD_FEC_MDC__GPIO4_IO23      0x3080
-				MX6SL_PAD_FEC_CRS_DV__GPIO4_IO25   0x3080
-				MX6SL_PAD_FEC_RXD0__GPIO4_IO17     0x3080
-				MX6SL_PAD_FEC_RXD1__GPIO4_IO18     0x3080
-				MX6SL_PAD_FEC_TX_EN__GPIO4_IO22    0x3080
-				MX6SL_PAD_FEC_TXD0__GPIO4_IO24     0x3080
-				MX6SL_PAD_FEC_TXD1__GPIO4_IO16     0x3080
-				MX6SL_PAD_FEC_REF_CLK__GPIO4_IO26  0x3080
-			>;
-		};
+	pinctrl_fec_sleep: fec-sleep-grp {
+		fsl,pins = <
+			MX6SL_PAD_FEC_MDC__GPIO4_IO23      0x3080
+			MX6SL_PAD_FEC_CRS_DV__GPIO4_IO25   0x3080
+			MX6SL_PAD_FEC_RXD0__GPIO4_IO17     0x3080
+			MX6SL_PAD_FEC_RXD1__GPIO4_IO18     0x3080
+			MX6SL_PAD_FEC_TX_EN__GPIO4_IO22    0x3080
+			MX6SL_PAD_FEC_TXD0__GPIO4_IO24     0x3080
+			MX6SL_PAD_FEC_TXD1__GPIO4_IO16     0x3080
+			MX6SL_PAD_FEC_REF_CLK__GPIO4_IO26  0x3080
+		>;
+	};
 
-		pinctrl_hp: hpgrp {
-			fsl,pins = <
-				MX6SL_PAD_FEC_RX_ER__GPIO4_IO19	  0x1b0b0
-			>;
-		};
+	pinctrl_hp: hpgrp {
+		fsl,pins = <
+			MX6SL_PAD_FEC_RX_ER__GPIO4_IO19	  0x1b0b0
+		>;
+	};
 
-		pinctrl_i2c1: i2c1grp {
-			fsl,pins = <
-				MX6SL_PAD_I2C1_SCL__I2C1_SCL	0x4001b8b1
-				MX6SL_PAD_I2C1_SDA__I2C1_SDA	0x4001b8b1
-			>;
-		};
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6SL_PAD_I2C1_SCL__I2C1_SCL	0x4001b8b1
+			MX6SL_PAD_I2C1_SDA__I2C1_SDA	0x4001b8b1
+		>;
+	};
 
 
-		pinctrl_i2c2: i2c2grp {
-			fsl,pins = <
-				MX6SL_PAD_I2C2_SCL__I2C2_SCL	0x4001b8b1
-				MX6SL_PAD_I2C2_SDA__I2C2_SDA	0x4001b8b1
-			>;
-		};
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6SL_PAD_I2C2_SCL__I2C2_SCL	0x4001b8b1
+			MX6SL_PAD_I2C2_SDA__I2C2_SDA	0x4001b8b1
+		>;
+	};
 
-		pinctrl_kpp: kppgrp {
-			fsl,pins = <
-				MX6SL_PAD_KEY_ROW0__KEY_ROW0    0x1b010
-				MX6SL_PAD_KEY_ROW1__KEY_ROW1    0x1b010
-				MX6SL_PAD_KEY_ROW2__KEY_ROW2    0x1b0b0
-				MX6SL_PAD_KEY_COL0__KEY_COL0    0x110b0
-				MX6SL_PAD_KEY_COL1__KEY_COL1    0x110b0
-				MX6SL_PAD_KEY_COL2__KEY_COL2    0x110b0
-			>;
-		};
+	pinctrl_kpp: kppgrp {
+		fsl,pins = <
+			MX6SL_PAD_KEY_ROW0__KEY_ROW0    0x1b010
+			MX6SL_PAD_KEY_ROW1__KEY_ROW1    0x1b010
+			MX6SL_PAD_KEY_ROW2__KEY_ROW2    0x1b0b0
+			MX6SL_PAD_KEY_COL0__KEY_COL0    0x110b0
+			MX6SL_PAD_KEY_COL1__KEY_COL1    0x110b0
+			MX6SL_PAD_KEY_COL2__KEY_COL2    0x110b0
+		>;
+	};
 
-		pinctrl_lcd: lcdgrp {
-			fsl,pins = <
-				MX6SL_PAD_LCD_DAT0__LCD_DATA00 0x1b0b0
-				MX6SL_PAD_LCD_DAT1__LCD_DATA01 0x1b0b0
-				MX6SL_PAD_LCD_DAT2__LCD_DATA02 0x1b0b0
-				MX6SL_PAD_LCD_DAT3__LCD_DATA03 0x1b0b0
-				MX6SL_PAD_LCD_DAT4__LCD_DATA04 0x1b0b0
-				MX6SL_PAD_LCD_DAT5__LCD_DATA05 0x1b0b0
-				MX6SL_PAD_LCD_DAT6__LCD_DATA06 0x1b0b0
-				MX6SL_PAD_LCD_DAT7__LCD_DATA07 0x1b0b0
-				MX6SL_PAD_LCD_DAT8__LCD_DATA08 0x1b0b0
-				MX6SL_PAD_LCD_DAT9__LCD_DATA09 0x1b0b0
-				MX6SL_PAD_LCD_DAT10__LCD_DATA10 0x1b0b0
-				MX6SL_PAD_LCD_DAT11__LCD_DATA11 0x1b0b0
-				MX6SL_PAD_LCD_DAT12__LCD_DATA12 0x1b0b0
-				MX6SL_PAD_LCD_DAT13__LCD_DATA13 0x1b0b0
-				MX6SL_PAD_LCD_DAT14__LCD_DATA14 0x1b0b0
-				MX6SL_PAD_LCD_DAT15__LCD_DATA15 0x1b0b0
-				MX6SL_PAD_LCD_DAT16__LCD_DATA16 0x1b0b0
-				MX6SL_PAD_LCD_DAT17__LCD_DATA17 0x1b0b0
-				MX6SL_PAD_LCD_DAT18__LCD_DATA18 0x1b0b0
-				MX6SL_PAD_LCD_DAT19__LCD_DATA19 0x1b0b0
-				MX6SL_PAD_LCD_DAT20__LCD_DATA20 0x1b0b0
-				MX6SL_PAD_LCD_DAT21__LCD_DATA21 0x1b0b0
-				MX6SL_PAD_LCD_DAT22__LCD_DATA22 0x1b0b0
-				MX6SL_PAD_LCD_DAT23__LCD_DATA23 0x1b0b0
-				MX6SL_PAD_LCD_CLK__LCD_CLK 0x1b0b0
-				MX6SL_PAD_LCD_ENABLE__LCD_ENABLE 0x1b0b0
-				MX6SL_PAD_LCD_HSYNC__LCD_HSYNC 0x1b0b0
-				MX6SL_PAD_LCD_VSYNC__LCD_VSYNC 0x1b0b0
-			>;
-		};
+	pinctrl_lcd: lcdgrp {
+		fsl,pins = <
+			MX6SL_PAD_LCD_DAT0__LCD_DATA00 0x1b0b0
+			MX6SL_PAD_LCD_DAT1__LCD_DATA01 0x1b0b0
+			MX6SL_PAD_LCD_DAT2__LCD_DATA02 0x1b0b0
+			MX6SL_PAD_LCD_DAT3__LCD_DATA03 0x1b0b0
+			MX6SL_PAD_LCD_DAT4__LCD_DATA04 0x1b0b0
+			MX6SL_PAD_LCD_DAT5__LCD_DATA05 0x1b0b0
+			MX6SL_PAD_LCD_DAT6__LCD_DATA06 0x1b0b0
+			MX6SL_PAD_LCD_DAT7__LCD_DATA07 0x1b0b0
+			MX6SL_PAD_LCD_DAT8__LCD_DATA08 0x1b0b0
+			MX6SL_PAD_LCD_DAT9__LCD_DATA09 0x1b0b0
+			MX6SL_PAD_LCD_DAT10__LCD_DATA10 0x1b0b0
+			MX6SL_PAD_LCD_DAT11__LCD_DATA11 0x1b0b0
+			MX6SL_PAD_LCD_DAT12__LCD_DATA12 0x1b0b0
+			MX6SL_PAD_LCD_DAT13__LCD_DATA13 0x1b0b0
+			MX6SL_PAD_LCD_DAT14__LCD_DATA14 0x1b0b0
+			MX6SL_PAD_LCD_DAT15__LCD_DATA15 0x1b0b0
+			MX6SL_PAD_LCD_DAT16__LCD_DATA16 0x1b0b0
+			MX6SL_PAD_LCD_DAT17__LCD_DATA17 0x1b0b0
+			MX6SL_PAD_LCD_DAT18__LCD_DATA18 0x1b0b0
+			MX6SL_PAD_LCD_DAT19__LCD_DATA19 0x1b0b0
+			MX6SL_PAD_LCD_DAT20__LCD_DATA20 0x1b0b0
+			MX6SL_PAD_LCD_DAT21__LCD_DATA21 0x1b0b0
+			MX6SL_PAD_LCD_DAT22__LCD_DATA22 0x1b0b0
+			MX6SL_PAD_LCD_DAT23__LCD_DATA23 0x1b0b0
+			MX6SL_PAD_LCD_CLK__LCD_CLK 0x1b0b0
+			MX6SL_PAD_LCD_ENABLE__LCD_ENABLE 0x1b0b0
+			MX6SL_PAD_LCD_HSYNC__LCD_HSYNC 0x1b0b0
+			MX6SL_PAD_LCD_VSYNC__LCD_VSYNC 0x1b0b0
+		>;
+	};
 
-		pinctrl_led: ledgrp {
-			fsl,pins = <
-				MX6SL_PAD_HSIC_STROBE__GPIO3_IO20 0x17059
-			>;
-		};
+	pinctrl_led: ledgrp {
+		fsl,pins = <
+			MX6SL_PAD_HSIC_STROBE__GPIO3_IO20 0x17059
+		>;
+	};
 
-		pinctrl_pwm1: pwmgrp {
-			fsl,pins = <
-				MX6SL_PAD_PWM1__PWM1_OUT 0x110b0
-			>;
-		};
+	pinctrl_pwm1: pwmgrp {
+		fsl,pins = <
+			MX6SL_PAD_PWM1__PWM1_OUT 0x110b0
+		>;
+	};
 
-		pinctrl_reg_lcd_3v3: reglcd3v3grp {
-			fsl,pins = <
-				MX6SL_PAD_KEY_ROW5__GPIO4_IO03    0x17059
-			>;
-		};
+	pinctrl_reg_lcd_3v3: reglcd3v3grp {
+		fsl,pins = <
+			MX6SL_PAD_KEY_ROW5__GPIO4_IO03    0x17059
+		>;
+	};
 
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX6SL_PAD_UART1_RXD__UART1_RX_DATA	0x1b0b1
-				MX6SL_PAD_UART1_TXD__UART1_TX_DATA	0x1b0b1
-			>;
-		};
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6SL_PAD_UART1_RXD__UART1_RX_DATA	0x1b0b1
+			MX6SL_PAD_UART1_TXD__UART1_TX_DATA	0x1b0b1
+		>;
+	};
 
-		pinctrl_usbotg1: usbotg1grp {
-			fsl,pins = <
-				MX6SL_PAD_EPDC_PWRCOM__USB_OTG1_ID	0x17059
-			>;
-		};
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = <
+			MX6SL_PAD_EPDC_PWRCOM__USB_OTG1_ID	0x17059
+		>;
+	};
 
-		pinctrl_usdhc1: usdhc1grp {
-			fsl,pins = <
-				MX6SL_PAD_SD1_CMD__SD1_CMD		0x17059
-				MX6SL_PAD_SD1_CLK__SD1_CLK		0x10059
-				MX6SL_PAD_SD1_DAT0__SD1_DATA0		0x17059
-				MX6SL_PAD_SD1_DAT1__SD1_DATA1		0x17059
-				MX6SL_PAD_SD1_DAT2__SD1_DATA2		0x17059
-				MX6SL_PAD_SD1_DAT3__SD1_DATA3		0x17059
-				MX6SL_PAD_SD1_DAT4__SD1_DATA4		0x17059
-				MX6SL_PAD_SD1_DAT5__SD1_DATA5		0x17059
-				MX6SL_PAD_SD1_DAT6__SD1_DATA6		0x17059
-				MX6SL_PAD_SD1_DAT7__SD1_DATA7		0x17059
-			>;
-		};
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_CMD__SD1_CMD		0x17059
+			MX6SL_PAD_SD1_CLK__SD1_CLK		0x10059
+			MX6SL_PAD_SD1_DAT0__SD1_DATA0		0x17059
+			MX6SL_PAD_SD1_DAT1__SD1_DATA1		0x17059
+			MX6SL_PAD_SD1_DAT2__SD1_DATA2		0x17059
+			MX6SL_PAD_SD1_DAT3__SD1_DATA3		0x17059
+			MX6SL_PAD_SD1_DAT4__SD1_DATA4		0x17059
+			MX6SL_PAD_SD1_DAT5__SD1_DATA5		0x17059
+			MX6SL_PAD_SD1_DAT6__SD1_DATA6		0x17059
+			MX6SL_PAD_SD1_DAT7__SD1_DATA7		0x17059
+		>;
+	};
 
-		pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
-			fsl,pins = <
-				MX6SL_PAD_SD1_CMD__SD1_CMD		0x170b9
-				MX6SL_PAD_SD1_CLK__SD1_CLK		0x100b9
-				MX6SL_PAD_SD1_DAT0__SD1_DATA0		0x170b9
-				MX6SL_PAD_SD1_DAT1__SD1_DATA1		0x170b9
-				MX6SL_PAD_SD1_DAT2__SD1_DATA2		0x170b9
-				MX6SL_PAD_SD1_DAT3__SD1_DATA3		0x170b9
-				MX6SL_PAD_SD1_DAT4__SD1_DATA4		0x170b9
-				MX6SL_PAD_SD1_DAT5__SD1_DATA5		0x170b9
-				MX6SL_PAD_SD1_DAT6__SD1_DATA6		0x170b9
-				MX6SL_PAD_SD1_DAT7__SD1_DATA7		0x170b9
-			>;
-		};
+	pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_CMD__SD1_CMD		0x170b9
+			MX6SL_PAD_SD1_CLK__SD1_CLK		0x100b9
+			MX6SL_PAD_SD1_DAT0__SD1_DATA0		0x170b9
+			MX6SL_PAD_SD1_DAT1__SD1_DATA1		0x170b9
+			MX6SL_PAD_SD1_DAT2__SD1_DATA2		0x170b9
+			MX6SL_PAD_SD1_DAT3__SD1_DATA3		0x170b9
+			MX6SL_PAD_SD1_DAT4__SD1_DATA4		0x170b9
+			MX6SL_PAD_SD1_DAT5__SD1_DATA5		0x170b9
+			MX6SL_PAD_SD1_DAT6__SD1_DATA6		0x170b9
+			MX6SL_PAD_SD1_DAT7__SD1_DATA7		0x170b9
+		>;
+	};
 
-		pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
-			fsl,pins = <
-				MX6SL_PAD_SD1_CMD__SD1_CMD		0x170f9
-				MX6SL_PAD_SD1_CLK__SD1_CLK		0x100f9
-				MX6SL_PAD_SD1_DAT0__SD1_DATA0		0x170f9
-				MX6SL_PAD_SD1_DAT1__SD1_DATA1		0x170f9
-				MX6SL_PAD_SD1_DAT2__SD1_DATA2		0x170f9
-				MX6SL_PAD_SD1_DAT3__SD1_DATA3		0x170f9
-				MX6SL_PAD_SD1_DAT4__SD1_DATA4		0x170f9
-				MX6SL_PAD_SD1_DAT5__SD1_DATA5		0x170f9
-				MX6SL_PAD_SD1_DAT6__SD1_DATA6		0x170f9
-				MX6SL_PAD_SD1_DAT7__SD1_DATA7		0x170f9
-			>;
-		};
+	pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_CMD__SD1_CMD		0x170f9
+			MX6SL_PAD_SD1_CLK__SD1_CLK		0x100f9
+			MX6SL_PAD_SD1_DAT0__SD1_DATA0		0x170f9
+			MX6SL_PAD_SD1_DAT1__SD1_DATA1		0x170f9
+			MX6SL_PAD_SD1_DAT2__SD1_DATA2		0x170f9
+			MX6SL_PAD_SD1_DAT3__SD1_DATA3		0x170f9
+			MX6SL_PAD_SD1_DAT4__SD1_DATA4		0x170f9
+			MX6SL_PAD_SD1_DAT5__SD1_DATA5		0x170f9
+			MX6SL_PAD_SD1_DAT6__SD1_DATA6		0x170f9
+			MX6SL_PAD_SD1_DAT7__SD1_DATA7		0x170f9
+		>;
+	};
 
-		pinctrl_usdhc2: usdhc2grp {
-			fsl,pins = <
-				MX6SL_PAD_SD2_CMD__SD2_CMD		0x17059
-				MX6SL_PAD_SD2_CLK__SD2_CLK		0x10059
-				MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x17059
-				MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x17059
-				MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x17059
-				MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x17059
-			>;
-		};
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x10059
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+		>;
+	};
 
-		pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
-			fsl,pins = <
-				MX6SL_PAD_SD2_CMD__SD2_CMD		0x170b9
-				MX6SL_PAD_SD2_CLK__SD2_CLK		0x100b9
-				MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x170b9
-				MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x170b9
-				MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x170b9
-				MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x170b9
-			>;
-		};
+	pinctrl_usdhc2_100mhz: usdhc2-100mhz-grp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x170b9
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x100b9
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x170b9
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x170b9
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x170b9
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x170b9
+		>;
+	};
 
-		pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
-			fsl,pins = <
-				MX6SL_PAD_SD2_CMD__SD2_CMD		0x170f9
-				MX6SL_PAD_SD2_CLK__SD2_CLK		0x100f9
-				MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x170f9
-				MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x170f9
-				MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x170f9
-				MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x170f9
-			>;
-		};
+	pinctrl_usdhc2_200mhz: usdhc2-200mhz-grp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x170f9
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x100f9
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x170f9
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x170f9
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x170f9
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x170f9
+		>;
+	};
 
-		pinctrl_usdhc3: usdhc3grp {
-			fsl,pins = <
-				MX6SL_PAD_SD3_CMD__SD3_CMD		0x17059
-				MX6SL_PAD_SD3_CLK__SD3_CLK		0x10059
-				MX6SL_PAD_SD3_DAT0__SD3_DATA0		0x17059
-				MX6SL_PAD_SD3_DAT1__SD3_DATA1		0x17059
-				MX6SL_PAD_SD3_DAT2__SD3_DATA2		0x17059
-				MX6SL_PAD_SD3_DAT3__SD3_DATA3		0x17059
-			>;
-		};
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6SL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+		>;
+	};
 
-		pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
-			fsl,pins = <
-				MX6SL_PAD_SD3_CMD__SD3_CMD		0x170b9
-				MX6SL_PAD_SD3_CLK__SD3_CLK		0x100b9
-				MX6SL_PAD_SD3_DAT0__SD3_DATA0		0x170b9
-				MX6SL_PAD_SD3_DAT1__SD3_DATA1		0x170b9
-				MX6SL_PAD_SD3_DAT2__SD3_DATA2		0x170b9
-				MX6SL_PAD_SD3_DAT3__SD3_DATA3		0x170b9
-			>;
-		};
+	pinctrl_usdhc3_100mhz: usdhc3-100mhz-grp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD		0x170b9
+			MX6SL_PAD_SD3_CLK__SD3_CLK		0x100b9
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0		0x170b9
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1		0x170b9
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2		0x170b9
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3		0x170b9
+		>;
+	};
 
-		pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
-			fsl,pins = <
-				MX6SL_PAD_SD3_CMD__SD3_CMD		0x170f9
-				MX6SL_PAD_SD3_CLK__SD3_CLK		0x100f9
-				MX6SL_PAD_SD3_DAT0__SD3_DATA0		0x170f9
-				MX6SL_PAD_SD3_DAT1__SD3_DATA1		0x170f9
-				MX6SL_PAD_SD3_DAT2__SD3_DATA2		0x170f9
-				MX6SL_PAD_SD3_DAT3__SD3_DATA3		0x170f9
-			>;
-		};
+	pinctrl_usdhc3_200mhz: usdhc3-200mhz-grp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD		0x170f9
+			MX6SL_PAD_SD3_CLK__SD3_CLK		0x100f9
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0		0x170f9
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1		0x170f9
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2		0x170f9
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3		0x170f9
+		>;
 	};
 };
 
@@ -584,10 +582,8 @@
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
-	status = "okay";
 };
 
 &reg_vdd1p1 {
diff --git a/arch/arm/boot/dts/nxp/imx/imx6sl-kobo-aura2.dts b/arch/arm/boot/dts/nxp/imx/imx6sl-kobo-aura2.dts
new file mode 100644
index 000000000000..657d0f1b6115
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6sl-kobo-aura2.dts
@@ -0,0 +1,555 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device tree for the Kobo Aura 2 ebook reader
+ *
+ * Name on mainboard is: 37NB-E60QL0+4B1
+ * Serials start with: E60QL2
+ *
+ * Copyright 2022 Andreas Kemnade
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "imx6sl.dtsi"
+
+/ {
+	model = "Kobo Aura 2";
+	compatible = "kobo,aura2", "fsl,imx6sl";
+
+	aliases {
+		mmc0 = &usdhc2;
+		mmc1 = &usdhc3;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		key-cover {
+			label = "Cover";
+			gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
+			linux,code = <SW_LID>;
+			linux,input-type = <EV_SW>;
+			wakeup-source;
+		};
+
+		key-power {
+			label = "Power";
+			gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+	};
+
+	leds: leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_led>;
+
+		led-0 {
+			label = "koboaura2:white:on";
+			gpios = <&gpio5 7 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_WHITE>;
+			linux,default-trigger = "timer";
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;
+	};
+
+	reg_wifi: regulator-wifi {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_power>;
+		regulator-name = "SD3_SPWR";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		gpio = <&gpio4 29 GPIO_ACTIVE_LOW>;
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_reset>;
+		post-power-on-delay-ms = <20>;
+		reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_sleep>;
+	status = "okay";
+
+	lm3630a: backlight@36 {
+		compatible = "ti,lm3630a";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lm3630a_bl_gpio>;
+		reg = <0x36>;
+		enable-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@0 {
+			reg = <0>;
+			led-sources = <0>;
+			label = "backlight";
+			default-brightness = <0>;
+			max-brightness = <255>;
+		};
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_sleep>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	/* eKTF2232 at 0x15 */
+	/* FP9928 at 0x48 */
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	ricoh619: pmic@32 {
+		compatible = "ricoh,rc5t619";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ricoh_gpio>;
+		reg = <0x32>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		system-power-controller;
+
+		regulators {
+			dcdc1_reg: DCDC1 {
+				regulator-name = "DCDC1";
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <900000>;
+					regulator-suspend-min-microvolt = <900000>;
+				};
+			};
+
+			/* Core3_3V3 */
+			dcdc2_reg: DCDC2 {
+				regulator-name = "DCDC2";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <3100000>;
+					regulator-suspend-min-microvolt = <3100000>;
+				};
+			};
+
+			dcdc3_reg: DCDC3 {
+				regulator-name = "DCDC3";
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <1140000>;
+					regulator-suspend-min-microvolt = <1140000>;
+				};
+			};
+
+			/* Core4_1V2 */
+			dcdc4_reg: DCDC4 {
+				regulator-name = "DCDC4";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <1140000>;
+					regulator-suspend-min-microvolt = <1140000>;
+				};
+			};
+
+			/* Core4_1V8 */
+			dcdc5_reg: DCDC5 {
+				regulator-name = "DCDC5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <1700000>;
+					regulator-suspend-min-microvolt = <1700000>;
+				};
+			};
+
+			/* IR_3V3 */
+			ldo1_reg: LDO1  {
+				regulator-name = "LDO1";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			/* Core1_3V3 */
+			ldo2_reg: LDO2  {
+				regulator-name = "LDO2";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <3000000>;
+					regulator-suspend-min-microvolt = <3000000>;
+				};
+			};
+
+			/* Core5_1V2 */
+			ldo3_reg: LDO3  {
+				regulator-name = "LDO3";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			ldo4_reg: LDO4 {
+				regulator-name = "LDO4";
+				regulator-boot-on;
+			};
+
+			/* SPD_3V3 */
+			ldo5_reg: LDO5 {
+				regulator-name = "LDO5";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			/* DDR_0V6 */
+			ldo6_reg: LDO6 {
+				regulator-name = "LDO6";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			/* VDD_PWM */
+			ldo7_reg: LDO7 {
+				regulator-name = "LDO7";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			/* ldo_1v8 */
+			ldo8_reg: LDO8 {
+				regulator-name = "LDO8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			ldo9_reg: LDO9 {
+				regulator-name = "LDO9";
+				regulator-boot-on;
+			};
+
+			ldo10_reg: LDO10 {
+				regulator-name = "LDO10";
+				regulator-boot-on;
+			};
+
+			ldortc1_reg: LDORTC1  {
+				regulator-name = "LDORTC1";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+		};
+	};
+};
+
+&reg_vdd1p1 {
+	vin-supply = <&dcdc2_reg>;
+};
+
+&reg_vdd2p5 {
+	vin-supply = <&dcdc2_reg>;
+};
+
+&reg_arm {
+	vin-supply = <&dcdc3_reg>;
+};
+
+&reg_soc {
+	vin-supply = <&dcdc1_reg>;
+};
+
+&reg_pu {
+	vin-supply = <&dcdc1_reg>;
+};
+
+&snvs_rtc {
+	/*
+	 * We are using the RTC in the PMIC, but this one is not disabled
+	 * in imx6sl.dtsi.
+	 */
+	status = "disabled";
+};
+
+&uart1 {
+	/* J4, through-holes */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart4 {
+	/* TP198, next to J4, SMD pads */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc2_sleep>;
+	non-removable;
+	status = "okay";
+
+	/* internal uSD card */
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc3_sleep>;
+	vmmc-supply = <&reg_wifi>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	cap-power-off-card;
+	non-removable;
+	status = "okay";
+
+	/*
+	 * RTL8189F SDIO WiFi
+	 */
+};
+
+&usbotg1 {
+	disable-over-current;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_gpio_keys: gpio-keysgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_DAT1__GPIO5_IO08  0x17059
+			MX6SL_PAD_SD1_DAT4__GPIO5_IO12  0x17059
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6SL_PAD_I2C1_SCL__I2C1_SCL	 0x4001f8b1
+			MX6SL_PAD_I2C1_SDA__I2C1_SDA	 0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c1_sleep: i2c1-sleepgrp {
+		fsl,pins = <
+			MX6SL_PAD_I2C1_SCL__I2C1_SCL	 0x400108b1
+			MX6SL_PAD_I2C1_SDA__I2C1_SDA	 0x400108b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6SL_PAD_I2C2_SCL__I2C2_SCL	 0x4001f8b1
+			MX6SL_PAD_I2C2_SDA__I2C2_SDA	 0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c2_sleep: i2c2-sleepgrp {
+		fsl,pins = <
+			MX6SL_PAD_I2C2_SCL__I2C2_SCL	 0x400108b1
+			MX6SL_PAD_I2C2_SDA__I2C2_SDA	 0x400108b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6SL_PAD_REF_CLK_24M__I2C3_SCL  0x4001f8b1
+			MX6SL_PAD_REF_CLK_32K__I2C3_SDA  0x4001f8b1
+		>;
+	};
+
+	pinctrl_led: ledgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_DAT6__GPIO5_IO07 0x17059
+		>;
+	};
+
+	pinctrl_lm3630a_bl_gpio: lm3630a-bl-gpiogrp {
+		fsl,pins = <
+			MX6SL_PAD_EPDC_PWRCTRL3__GPIO2_IO10 0x10059 /* HWEN */
+		>;
+	};
+
+	pinctrl_ricoh_gpio: ricoh-gpiogrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_CLK__GPIO5_IO15	0x1b8b1 /* ricoh619 chg */
+			MX6SL_PAD_SD1_DAT0__GPIO5_IO11	0x1b8b1 /* ricoh619 irq */
+			MX6SL_PAD_KEY_COL2__GPIO3_IO28	0x1b8b1 /* ricoh619 bat_low_int */
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6SL_PAD_UART1_TXD__UART1_TX_DATA 0x1b0b1
+			MX6SL_PAD_UART1_RXD__UART1_RX_DATA 0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6SL_PAD_KEY_ROW6__UART4_TX_DATA 0x1b0b1
+			MX6SL_PAD_KEY_COL6__UART4_RX_DATA 0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = <
+			MX6SL_PAD_EPDC_PWRCOM__USB_OTG1_ID 0x17059
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x13059
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x170b9
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x130b9
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x170b9
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x170b9
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x170b9
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x170b9
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x170f9
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x130f9
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x170f9
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x170f9
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x170f9
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x170f9
+		>;
+	};
+
+	pinctrl_usdhc2_sleep: usdhc2-sleepgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__GPIO5_IO04		0x100f9
+			MX6SL_PAD_SD2_CLK__GPIO5_IO05		0x100f9
+			MX6SL_PAD_SD2_DAT0__GPIO5_IO01		0x100f9
+			MX6SL_PAD_SD2_DAT1__GPIO4_IO30		0x100f9
+			MX6SL_PAD_SD2_DAT2__GPIO5_IO03		0x100f9
+			MX6SL_PAD_SD2_DAT3__GPIO4_IO28		0x100f9
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD	0x11059
+			MX6SL_PAD_SD3_CLK__SD3_CLK	0x11059
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0	0x11059
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1	0x11059
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2	0x11059
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3	0x11059
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD	0x170b9
+			MX6SL_PAD_SD3_CLK__SD3_CLK	0x170b9
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0	0x170b9
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1	0x170b9
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2	0x170b9
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD	0x170f9
+			MX6SL_PAD_SD3_CLK__SD3_CLK	0x170f9
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0	0x170f9
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1	0x170f9
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2	0x170f9
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3	0x170f9
+		>;
+	};
+
+	pinctrl_usdhc3_sleep: usdhc3-sleepgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__GPIO5_IO21	0x100c1
+			MX6SL_PAD_SD3_CLK__GPIO5_IO18	0x100c1
+			MX6SL_PAD_SD3_DAT0__GPIO5_IO19	0x100c1
+			MX6SL_PAD_SD3_DAT1__GPIO5_IO20	0x100c1
+			MX6SL_PAD_SD3_DAT2__GPIO5_IO16	0x100c1
+			MX6SL_PAD_SD3_DAT3__GPIO5_IO17	0x100c1
+		>;
+	};
+
+	pinctrl_wifi_power: wifi-powergrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_DAT6__GPIO4_IO29	0x10059	/* WIFI_3V3_ON */
+		>;
+	};
+
+	pinctrl_wifi_reset: wifi-resetgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_DAT7__GPIO5_IO00	0x10059	/* WIFI_RST */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6sl-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx6sl-pinfunc.h
index bcf16060ecdc..bcf16060ecdc 100644
--- a/arch/arm/boot/dts/imx6sl-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx6sl-pinfunc.h
diff --git a/arch/arm/boot/dts/imx6sl-tolino-shine2hd.dts b/arch/arm/boot/dts/nxp/imx/imx6sl-tolino-shine2hd.dts
index a17b8bbbdb95..b6c336e3079e 100644
--- a/arch/arm/boot/dts/imx6sl-tolino-shine2hd.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sl-tolino-shine2hd.dts
@@ -18,6 +18,21 @@
 	model = "Tolino Shine 2 HD";
 	compatible = "kobo,tolino-shine2hd", "fsl,imx6sl";
 
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&ec 0 50000>;
+		power-supply = <&backlight_regulator>;
+	};
+
+	backlight_regulator: regulator-backlight {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight_power>;
+		regulator-name = "backlight";
+		gpio = <&gpio2 10 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
 	chosen {
 		stdout-path = &uart1;
 	};
@@ -27,7 +42,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_keys>;
 
-		cover {
+		key-cover {
 			label = "Cover";
 			gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
 			linux,code = <SW_LID>;
@@ -35,19 +50,19 @@
 			wakeup-source;
 		};
 
-		fl {
+		key-fl {
 			label = "Frontlight";
 			gpios = <&gpio3 26 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_BRIGHTNESS_CYCLE>;
 		};
 
-		home {
+		key-home {
 			label = "Home";
 			gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_HOME>;
 		};
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -60,11 +75,17 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_led>;
 
-		on {
+		led-0 {
 			label = "tolinoshine2hd:white:on";
 			gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "timer";
 		};
+
+		led-1 {
+			label = "tolinoshine2hd:white:backlightboost";
+			gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "none";
+		};
 	};
 
 	memory@80000000 {
@@ -117,11 +138,13 @@
 		pinctrl-0 = <&pinctrl_zforce>;
 		reg = <0x50>;
 		interrupt-parent = <&gpio5>;
-		interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+		interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
 		vdd-supply = <&ldo1_reg>;
 		reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
-		x-size = <1072>;
-		y-size = <1448>;
+		touchscreen-size-x = <1072>;
+		touchscreen-size-y = <1448>;
+		touchscreen-swapped-x-y;
+		touchscreen-inverted-x;
 	};
 
 	/* TODO: TPS65185 PMIC for E Ink at 0x68 */
@@ -140,7 +163,7 @@
 		pinctrl-0 = <&pinctrl_ricoh_gpio>;
 		reg = <0x32>;
 		interrupt-parent = <&gpio5>;
-		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
 		system-power-controller;
 
 		regulators {
@@ -299,6 +322,12 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hog>;
 
+	pinctrl_backlight_power: backlight-powergrp {
+		fsl,pins = <
+			MX6SL_PAD_EPDC_PWRCTRL3__GPIO2_IO10 0x10059
+		>;
+	};
+
 	pinctrl_gpio_keys: gpio-keysgrp {
 		fsl,pins = <
 			MX6SL_PAD_SD1_DAT1__GPIO5_IO08  0x17059
@@ -353,7 +382,7 @@
 		>;
 	};
 
-	pinctrl_i2c1_sleep: i2c1grp-sleep {
+	pinctrl_i2c1_sleep: i2c1sleep-grp {
 		fsl,pins = <
 			MX6SL_PAD_I2C1_SCL__I2C1_SCL	 0x400108b1
 			MX6SL_PAD_I2C1_SDA__I2C1_SDA	 0x400108b1
@@ -367,7 +396,7 @@
 		>;
 	};
 
-	pinctrl_i2c2_sleep: i2c2grp-sleep {
+	pinctrl_i2c2_sleep: i2c2sleep-grp {
 		fsl,pins = <
 			MX6SL_PAD_I2C2_SCL__I2C2_SCL	 0x400108b1
 			MX6SL_PAD_I2C2_SDA__I2C2_SDA	 0x400108b1
@@ -383,7 +412,8 @@
 
 	pinctrl_led: ledgrp {
 		fsl,pins = <
-			MX6SL_PAD_SD1_DAT2__GPIO5_IO13 0x17059
+			MX6SL_PAD_SD1_DAT2__GPIO5_IO13    0x17059
+			MX6SL_PAD_EPDC_SDCE2__GPIO1_IO29  0x17059
 		>;
 	};
 
@@ -426,7 +456,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_100mhz: usdhc2grp-100mhz {
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
 		fsl,pins = <
 			MX6SL_PAD_SD2_CMD__SD2_CMD		0x170b9
 			MX6SL_PAD_SD2_CLK__SD2_CLK		0x130b9
@@ -437,7 +467,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_200mhz: usdhc2grp-200mhz {
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
 		fsl,pins = <
 			MX6SL_PAD_SD2_CMD__SD2_CMD		0x170f9
 			MX6SL_PAD_SD2_CLK__SD2_CLK		0x130f9
@@ -448,7 +478,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_sleep: usdhc2grp-sleep {
+	pinctrl_usdhc2_sleep: usdhc2sleep-grp {
 		fsl,pins = <
 			MX6SL_PAD_SD2_CMD__GPIO5_IO04		0x100f9
 			MX6SL_PAD_SD2_CLK__GPIO5_IO05		0x100f9
@@ -470,7 +500,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_100mhz: usdhc3grp-100mhz {
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
 		fsl,pins = <
 			MX6SL_PAD_SD3_CMD__SD3_CMD	0x170b9
 			MX6SL_PAD_SD3_CLK__SD3_CLK	0x170b9
@@ -481,7 +511,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_200mhz: usdhc3grp-200mhz {
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
 		fsl,pins = <
 			MX6SL_PAD_SD3_CMD__SD3_CMD	0x170f9
 			MX6SL_PAD_SD3_CLK__SD3_CLK	0x170f9
@@ -492,7 +522,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_sleep: usdhc3grp-sleep {
+	pinctrl_usdhc3_sleep: usdhc3sleep-grp {
 		fsl,pins = <
 			MX6SL_PAD_SD3_CMD__GPIO5_IO21	0x100c1
 			MX6SL_PAD_SD3_CLK__GPIO5_IO18	0x100c1
@@ -597,6 +627,7 @@
 
 &usbotg1 {
 	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
 	disable-over-current;
 	srp-disable;
 	hnp-disable;
diff --git a/arch/arm/boot/dts/imx6sl-tolino-shine3.dts b/arch/arm/boot/dts/nxp/imx/imx6sl-tolino-shine3.dts
index e3f1e8d79528..5ba6f15e9ed5 100644
--- a/arch/arm/boot/dts/imx6sl-tolino-shine3.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sl-tolino-shine3.dts
@@ -52,6 +52,13 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hog>;
 
+	pinctrl_cyttsp5_gpio: cyttsp5-gpiogrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_DAT3__GPIO5_IO06                0x17059 /* TP_INT */
+			MX6SL_PAD_SD1_DAT2__GPIO5_IO13                0x10059 /* TP_RST */
+		>;
+	};
+
 	pinctrl_gpio_keys: gpio-keysgrp {
 		fsl,pins = <
 			MX6SL_PAD_SD1_DAT1__GPIO5_IO08	0x17059	/* PWR_SW */
@@ -104,7 +111,7 @@
 		>;
 	};
 
-	pinctrl_i2c1_sleep: i2c1grp-sleep {
+	pinctrl_i2c1_sleep: i2c1sleep-grp {
 		fsl,pins = <
 			MX6SL_PAD_I2C1_SCL__I2C1_SCL	 0x400108b1
 			MX6SL_PAD_I2C1_SDA__I2C1_SDA	 0x400108b1
@@ -118,7 +125,7 @@
 		>;
 	};
 
-	pinctrl_i2c2_sleep: i2c2grp-sleep {
+	pinctrl_i2c2_sleep: i2c2sleep-grp {
 		fsl,pins = <
 			MX6SL_PAD_I2C2_SCL__I2C2_SCL	 0x400108b1
 			MX6SL_PAD_I2C2_SDA__I2C2_SDA	 0x400108b1
@@ -183,7 +190,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_100mhz: usdhc2grp-100mhz {
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
 		fsl,pins = <
 			MX6SL_PAD_SD2_CMD__SD2_CMD		0x170b9
 			MX6SL_PAD_SD2_CLK__SD2_CLK		0x130b9
@@ -194,7 +201,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_200mhz: usdhc2grp-200mhz {
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
 		fsl,pins = <
 			MX6SL_PAD_SD2_CMD__SD2_CMD		0x170f9
 			MX6SL_PAD_SD2_CLK__SD2_CLK		0x130f9
@@ -205,7 +212,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_sleep: usdhc2grp-sleep {
+	pinctrl_usdhc2_sleep: usdhc2sleep-grp {
 		fsl,pins = <
 			MX6SL_PAD_SD2_CMD__GPIO5_IO04		0x100f9
 			MX6SL_PAD_SD2_CLK__GPIO5_IO05		0x100f9
@@ -227,7 +234,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_100mhz: usdhc3grp-100mhz {
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
 		fsl,pins = <
 			MX6SL_PAD_SD3_CMD__SD3_CMD	0x170b9
 			MX6SL_PAD_SD3_CLK__SD3_CLK	0x170b9
@@ -238,7 +245,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_200mhz: usdhc3grp-200mhz {
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
 		fsl,pins = <
 			MX6SL_PAD_SD3_CMD__SD3_CMD	0x170f9
 			MX6SL_PAD_SD3_CLK__SD3_CLK	0x170f9
@@ -249,7 +256,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_sleep: usdhc3grp-sleep {
+	pinctrl_usdhc3_sleep: usdhc3sleep-grp {
 		fsl,pins = <
 			MX6SL_PAD_SD3_CMD__GPIO5_IO21	0x100c1
 			MX6SL_PAD_SD3_CLK__GPIO5_IO18	0x100c1
diff --git a/arch/arm/boot/dts/nxp/imx/imx6sl-tolino-vision.dts b/arch/arm/boot/dts/nxp/imx/imx6sl-tolino-vision.dts
new file mode 100644
index 000000000000..2694fe18a91b
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6sl-tolino-vision.dts
@@ -0,0 +1,490 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device tree for the Tolino Vison ebook reader
+ *
+ * Name on mainboard is: 37NB-E60Q30+4A3
+ * Serials start with: 6032
+ *
+ * Copyright 2023 Andreas Kemnade
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "imx6sl.dtsi"
+
+/ {
+	model = "Tolino Vision";
+	compatible = "kobo,tolino-vision", "fsl,imx6sl";
+
+	aliases {
+		mmc0 = &usdhc4;
+		mmc1 = &usdhc2;
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&ec 0 50000>;
+		power-supply = <&backlight_regulator>;
+	};
+
+	backlight_regulator: regulator-backlight {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight_power>;
+		regulator-name = "backlight";
+		gpio = <&gpio2 10 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		key-cover {
+			/* magnetic sensor in the corner next to the uSD slot */
+			label = "Cover";
+			gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
+			linux,code = <SW_LID>;
+			linux,input-type = <EV_SW>;
+			wakeup-source;
+		};
+
+		key-fl {
+			label = "Frontlight";
+			gpios = <&gpio3 26 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_BRIGHTNESS_CYCLE>;
+		};
+
+		key-power {
+			label = "Power";
+			gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+	};
+
+	leds: leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+
+		led-0 {
+			/* LED on home button */
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio5 10 GPIO_ACTIVE_LOW>;
+		};
+
+		led-1 {
+			/* LED on power button */
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&gpio5 7 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "timer";
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reg_wifi: regulator-wifi {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_power>;
+		regulator-name = "SD3_SPWR";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		gpio = <&gpio4 29 GPIO_ACTIVE_LOW>;
+	};
+
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_reset>;
+		post-power-on-delay-ms = <20>;
+		reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default","sleep";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_sleep>;
+	status = "okay";
+
+	touchscreen@15 {
+		compatible = "elan,ektf2132";
+		reg = <0x15>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ts>;
+		power-gpios = <&gpio5 13 GPIO_ACTIVE_HIGH>;
+		interrupts-extended = <&gpio5 6 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+	accelerometer@1d {
+		compatible = "fsl,mma8652";
+		reg = <0x1d>;
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default","sleep";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_sleep>;
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	ec: embedded-controller@43 {
+		compatible = "netronix,ntxec";
+		reg = <0x43>;
+		#pwm-cells = <2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ec>;
+		interrupts-extended = <&gpio5 11 IRQ_TYPE_EDGE_FALLING>;
+		system-power-controller;
+	};
+};
+
+&snvs_rtc {
+	/*
+	 * We are using the RTC in the PMIC, but this one is not disabled
+	 * in imx6sl.dtsi.
+	 */
+	status = "disabled";
+};
+
+&uart1 {
+	/* J4 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart4 {
+	/* J9 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc2_sleep>;
+	cd-gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	/* removable uSD card */
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc3_sleep>;
+	vmmc-supply = <&reg_wifi>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	cap-power-off-card;
+	non-removable;
+	status = "okay";
+
+	/* CyberTan WC121 (BCM43362) SDIO WiFi */
+};
+
+&usdhc4 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	pinctrl-1 = <&pinctrl_usdhc4_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc4_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc4_sleep>;
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	status = "okay";
+
+	/* internal eMMC */
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	disable-over-current;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_backlight_power: backlight-powergrp {
+		fsl,pins = <
+			MX6SL_PAD_EPDC_PWRCTRL3__GPIO2_IO10 0x10059
+		>;
+	};
+
+	pinctrl_ec: ecgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_DAT0__GPIO5_IO11  0x17000
+		>;
+	};
+
+	pinctrl_gpio_keys: gpio-keysgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_DAT1__GPIO5_IO08  0x110B0
+			MX6SL_PAD_SD1_DAT4__GPIO5_IO12  0x110B0
+			MX6SL_PAD_KEY_COL1__GPIO3_IO26  0x11030
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6SL_PAD_I2C1_SCL__I2C1_SCL	 0x4001f8b1
+			MX6SL_PAD_I2C1_SDA__I2C1_SDA	 0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c1_sleep: i2c1-sleepgrp {
+		fsl,pins = <
+			MX6SL_PAD_I2C1_SCL__I2C1_SCL	 0x400108b1
+			MX6SL_PAD_I2C1_SDA__I2C1_SDA	 0x400108b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6SL_PAD_I2C2_SCL__I2C2_SCL	 0x4001f8b1
+			MX6SL_PAD_I2C2_SDA__I2C2_SDA	 0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c2_sleep: i2c2-sleepgrp {
+		fsl,pins = <
+			MX6SL_PAD_I2C2_SCL__I2C2_SCL	 0x400108b1
+			MX6SL_PAD_I2C2_SDA__I2C2_SDA	 0x400108b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6SL_PAD_REF_CLK_24M__I2C3_SCL  0x4001f8b1
+			MX6SL_PAD_REF_CLK_32K__I2C3_SDA  0x4001f8b1
+		>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_DAT6__GPIO5_IO07    0x17059
+			MX6SL_PAD_SD1_DAT7__GPIO5_IO10    0x17059
+			MX6SL_PAD_EPDC_SDCE2__GPIO1_IO29  0x17059
+		>;
+	};
+
+	pinctrl_ts: tsgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD1_DAT2__GPIO5_IO13	0x110B0
+			MX6SL_PAD_SD1_DAT3__GPIO5_IO06	0x1B0B1
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6SL_PAD_UART1_TXD__UART1_TX_DATA 0x1b0b1
+			MX6SL_PAD_UART1_RXD__UART1_RX_DATA 0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6SL_PAD_KEY_ROW6__UART4_TX_DATA 0x1b0b1
+			MX6SL_PAD_KEY_COL6__UART4_RX_DATA 0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = <
+			MX6SL_PAD_EPDC_PWRCOM__USB_OTG1_ID 0x17059
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x13059
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x17059
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x17059
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x17059
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x17059
+			MX6SL_PAD_SD2_DAT4__GPIO5_IO02		0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x170b9
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x130b9
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x170b9
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x170b9
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x170b9
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x170b9
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x170f9
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x130f9
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x170f9
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x170f9
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x170f9
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x170f9
+		>;
+	};
+
+	pinctrl_usdhc2_sleep: usdhc2-sleepgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__GPIO5_IO04		0x100f9
+			MX6SL_PAD_SD2_CLK__GPIO5_IO05		0x100f9
+			MX6SL_PAD_SD2_DAT0__GPIO5_IO01		0x100f9
+			MX6SL_PAD_SD2_DAT1__GPIO4_IO30		0x100f9
+			MX6SL_PAD_SD2_DAT2__GPIO5_IO03		0x100f9
+			MX6SL_PAD_SD2_DAT3__GPIO4_IO28		0x100f9
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD	0x11059
+			MX6SL_PAD_SD3_CLK__SD3_CLK	0x11059
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0	0x11059
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1	0x11059
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2	0x11059
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3	0x11059
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD	0x170b9
+			MX6SL_PAD_SD3_CLK__SD3_CLK	0x170b9
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0	0x170b9
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1	0x170b9
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2	0x170b9
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD	0x170f9
+			MX6SL_PAD_SD3_CLK__SD3_CLK	0x170f9
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0	0x170f9
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1	0x170f9
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2	0x170f9
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3	0x170f9
+		>;
+	};
+
+	pinctrl_usdhc3_sleep: usdhc3-sleepgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__GPIO5_IO21	0x100c1
+			MX6SL_PAD_SD3_CLK__GPIO5_IO18	0x100c1
+			MX6SL_PAD_SD3_DAT0__GPIO5_IO19	0x100c1
+			MX6SL_PAD_SD3_DAT1__GPIO5_IO20	0x100c1
+			MX6SL_PAD_SD3_DAT2__GPIO5_IO16	0x100c1
+			MX6SL_PAD_SD3_DAT3__GPIO5_IO17	0x100c1
+		>;
+	};
+
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6SL_PAD_FEC_TX_CLK__SD4_CMD		0x17059
+			MX6SL_PAD_FEC_MDIO__SD4_CLK		0x13059
+			MX6SL_PAD_FEC_RX_ER__SD4_DATA0		0x17059
+			MX6SL_PAD_FEC_CRS_DV__SD4_DATA1		0x17059
+			MX6SL_PAD_FEC_RXD1__SD4_DATA2		0x17059
+			MX6SL_PAD_FEC_TXD0__SD4_DATA3		0x17059
+			MX6SL_PAD_FEC_MDC__SD4_DATA4		0x17059
+			MX6SL_PAD_FEC_RXD0__SD4_DATA5		0x17059
+			MX6SL_PAD_FEC_TX_EN__SD4_DATA6		0x17059
+			MX6SL_PAD_FEC_TXD1__SD4_DATA7		0x17059
+			MX6SL_PAD_FEC_REF_CLK__SD4_RESET	0x17068
+		>;
+	};
+
+	pinctrl_usdhc4_100mhz: usdhc4-100mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_FEC_TX_CLK__SD4_CMD		0x170b9
+			MX6SL_PAD_FEC_MDIO__SD4_CLK		0x130b9
+			MX6SL_PAD_FEC_RX_ER__SD4_DATA0		0x170b9
+			MX6SL_PAD_FEC_CRS_DV__SD4_DATA1		0x170b9
+			MX6SL_PAD_FEC_RXD1__SD4_DATA2		0x170b9
+			MX6SL_PAD_FEC_TXD0__SD4_DATA3		0x170b9
+			MX6SL_PAD_FEC_MDC__SD4_DATA4		0x170b9
+			MX6SL_PAD_FEC_RXD0__SD4_DATA5		0x170b9
+			MX6SL_PAD_FEC_TX_EN__SD4_DATA6		0x170b9
+			MX6SL_PAD_FEC_TXD1__SD4_DATA7		0x170b9
+		>;
+	};
+
+	pinctrl_usdhc4_200mhz: usdhc4-200mhzgrp {
+		fsl,pins = <
+			MX6SL_PAD_FEC_TX_CLK__SD4_CMD		0x170f9
+			MX6SL_PAD_FEC_MDIO__SD4_CLK		0x130f9
+			MX6SL_PAD_FEC_RX_ER__SD4_DATA0		0x170f9
+			MX6SL_PAD_FEC_CRS_DV__SD4_DATA1		0x170f9
+			MX6SL_PAD_FEC_RXD1__SD4_DATA2		0x170f9
+			MX6SL_PAD_FEC_TXD0__SD4_DATA3		0x170f9
+			MX6SL_PAD_FEC_MDC__SD4_DATA4		0x170f9
+			MX6SL_PAD_FEC_RXD0__SD4_DATA5		0x170f9
+			MX6SL_PAD_FEC_TX_EN__SD4_DATA6		0x170f9
+			MX6SL_PAD_FEC_TXD1__SD4_DATA7		0x170f9
+		>;
+	};
+
+	pinctrl_usdhc4_sleep: usdhc4-sleepgrp {
+		fsl,pins = <
+			MX6SL_PAD_FEC_TX_CLK__GPIO4_IO21	0x100c1
+			MX6SL_PAD_FEC_MDIO__GPIO4_IO20		0x100c1
+			MX6SL_PAD_FEC_RX_ER__GPIO4_IO19		0x100c1
+			MX6SL_PAD_FEC_CRS_DV__GPIO4_IO25	0x100c1
+			MX6SL_PAD_FEC_RXD1__GPIO4_IO18		0x100c1
+			MX6SL_PAD_FEC_TXD0__GPIO4_IO24		0x100c1
+			MX6SL_PAD_FEC_MDC__GPIO4_IO23		0x100c1
+			MX6SL_PAD_FEC_RXD0__GPIO4_IO17		0x100c1
+			MX6SL_PAD_FEC_TX_EN__GPIO4_IO22		0x100c1
+			MX6SL_PAD_FEC_TXD1__GPIO4_IO16		0x100c1
+		>;
+	};
+
+	pinctrl_wifi_power: wifi-powergrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_DAT6__GPIO4_IO29	0x10059	/* WIFI_3V3_ON */
+		>;
+	};
+
+	pinctrl_wifi_reset: wifi-resetgrp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_DAT7__GPIO5_IO00	0x10059	/* WIFI_RST */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6sl-tolino-vision5.dts b/arch/arm/boot/dts/nxp/imx/imx6sl-tolino-vision5.dts
index ff6118df3946..a2534c422a52 100644
--- a/arch/arm/boot/dts/imx6sl-tolino-vision5.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sl-tolino-vision5.dts
@@ -52,6 +52,13 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hog>;
 
+	pinctrl_cyttsp5_gpio: cyttsp5-gpiogrp {
+		fsl,pins = <
+			MX6SL_PAD_FEC_TXD0__GPIO4_IO24          0x17059 /* TP_INT */
+			MX6SL_PAD_FEC_RXD1__GPIO4_IO18          0x10059 /* TP_RST */
+		>;
+	};
+
 	pinctrl_gpio_keys: gpio-keysgrp {
 		fsl,pins = <
 			MX6SL_PAD_FEC_CRS_DV__GPIO4_IO25	0x17059	/* PWR_SW */
@@ -104,7 +111,7 @@
 		>;
 	};
 
-	pinctrl_i2c1_sleep: i2c1grp-sleep {
+	pinctrl_i2c1_sleep: i2c1sleep-grp {
 		fsl,pins = <
 			MX6SL_PAD_I2C1_SCL__I2C1_SCL	 0x400108b1
 			MX6SL_PAD_I2C1_SDA__I2C1_SDA	 0x400108b1
@@ -118,7 +125,7 @@
 		>;
 	};
 
-	pinctrl_i2c2_sleep: i2c2grp-sleep {
+	pinctrl_i2c2_sleep: i2c2sleep-grp {
 		fsl,pins = <
 			MX6SL_PAD_I2C2_SCL__I2C2_SCL	 0x400108b1
 			MX6SL_PAD_I2C2_SDA__I2C2_SDA	 0x400108b1
diff --git a/arch/arm/boot/dts/imx6sl-warp.dts b/arch/arm/boot/dts/nxp/imx/imx6sl-warp.dts
index 9d7c8884892a..a5d48c382314 100644
--- a/arch/arm/boot/dts/imx6sl-warp.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sl-warp.dts
@@ -125,110 +125,108 @@
 };
 
 &iomuxc {
-	imx6sl-warp {
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX6SL_PAD_UART1_RXD__UART1_RX_DATA	0x41b0b1
-				MX6SL_PAD_UART1_TXD__UART1_TX_DATA	0x41b0b1
-			>;
-		};
-
-
-		pinctrl_uart3: uart3grp {
-			fsl,pins = <
-				MX6SL_PAD_AUD_RXC__UART3_RX_DATA	0x41b0b1
-				MX6SL_PAD_AUD_RXC__UART3_TX_DATA	0x41b0b1
-			>;
-		};
-
-		pinctrl_uart5: uart5grp {
-			fsl,pins = <
-				MX6SL_PAD_ECSPI1_SCLK__UART5_RX_DATA	0x41b0b1
-				MX6SL_PAD_ECSPI1_MOSI__UART5_TX_DATA	0x41b0b1
-				MX6SL_PAD_ECSPI1_MISO__UART5_RTS_B	0x4130b1
-				MX6SL_PAD_ECSPI1_SS0__UART5_CTS_B	0x4130b1
-			>;
-		};
-
-		pinctrl_usdhc2: usdhc2grp {
-			fsl,pins = <
-				MX6SL_PAD_SD2_CMD__SD2_CMD		0x417059
-				MX6SL_PAD_SD2_CLK__SD2_CLK		0x410059
-				MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x417059
-				MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x417059
-				MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x417059
-				MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x417059
-				MX6SL_PAD_SD2_DAT4__SD2_DATA4		0x417059
-				MX6SL_PAD_SD2_DAT5__SD2_DATA5		0x417059
-				MX6SL_PAD_SD2_DAT6__SD2_DATA6		0x417059
-				MX6SL_PAD_SD2_DAT7__SD2_DATA7		0x417059
-				MX6SL_PAD_SD2_RST__SD2_RESET		0x417059
-			>;
-		};
-
-		pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
-			fsl,pins = <
-				MX6SL_PAD_SD2_CMD__SD2_CMD		0x4170b9
-				MX6SL_PAD_SD2_CLK__SD2_CLK		0x4100b9
-				MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x4170b9
-				MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x4170b9
-				MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x4170b9
-				MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x4170b9
-				MX6SL_PAD_SD2_DAT4__SD2_DATA4		0x4170b9
-				MX6SL_PAD_SD2_DAT5__SD2_DATA5		0x4170b9
-				MX6SL_PAD_SD2_DAT6__SD2_DATA6		0x4170b9
-				MX6SL_PAD_SD2_DAT7__SD2_DATA7		0x4170b9
-				MX6SL_PAD_SD2_RST__SD2_RESET		0x4170b9
-			>;
-		};
-
-		pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
-			fsl,pins = <
-				MX6SL_PAD_SD2_CMD__SD2_CMD		0x4170f9
-				MX6SL_PAD_SD2_CLK__SD2_CLK		0x4100f9
-				MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x4170f9
-				MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x4170f9
-				MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x4170f9
-				MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x4170f9
-				MX6SL_PAD_SD2_DAT4__SD2_DATA4		0x4170f9
-				MX6SL_PAD_SD2_DAT5__SD2_DATA5		0x4170f9
-				MX6SL_PAD_SD2_DAT6__SD2_DATA6		0x4170f9
-				MX6SL_PAD_SD2_DAT7__SD2_DATA7		0x4170f9
-				MX6SL_PAD_SD2_RST__SD2_RESET		0x4170f9
-			>;
-		};
-
-		pinctrl_usdhc3: usdhc3grp {
-			fsl,pins = <
-				MX6SL_PAD_SD3_CMD__SD3_CMD		0x417059
-				MX6SL_PAD_SD3_CLK__SD3_CLK		0x410059
-				MX6SL_PAD_SD3_DAT0__SD3_DATA0		0x417059
-				MX6SL_PAD_SD3_DAT1__SD3_DATA1		0x417059
-				MX6SL_PAD_SD3_DAT2__SD3_DATA2		0x417059
-				MX6SL_PAD_SD3_DAT3__SD3_DATA3		0x417059
-			>;
-		};
-
-		pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
-			fsl,pins = <
-				MX6SL_PAD_SD3_CMD__SD3_CMD		0x4170b9
-				MX6SL_PAD_SD3_CLK__SD3_CLK		0x4100b9
-				MX6SL_PAD_SD3_DAT0__SD3_DATA0		0x4170b9
-				MX6SL_PAD_SD3_DAT1__SD3_DATA1		0x4170b9
-				MX6SL_PAD_SD3_DAT2__SD3_DATA2		0x4170b9
-				MX6SL_PAD_SD3_DAT3__SD3_DATA3		0x4170b9
-			>;
-		};
-
-		pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
-			fsl,pins = <
-				MX6SL_PAD_SD3_CMD__SD3_CMD		0x4170f9
-				MX6SL_PAD_SD3_CLK__SD3_CLK		0x4100f9
-				MX6SL_PAD_SD3_DAT0__SD3_DATA0		0x4170f9
-				MX6SL_PAD_SD3_DAT1__SD3_DATA1		0x4170f9
-				MX6SL_PAD_SD3_DAT2__SD3_DATA2		0x4170f9
-				MX6SL_PAD_SD3_DAT3__SD3_DATA3		0x4170f9
-			>;
-		};
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6SL_PAD_UART1_RXD__UART1_RX_DATA	0x41b0b1
+			MX6SL_PAD_UART1_TXD__UART1_TX_DATA	0x41b0b1
+		>;
+	};
+
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6SL_PAD_AUD_RXC__UART3_RX_DATA	0x41b0b1
+			MX6SL_PAD_AUD_RXC__UART3_TX_DATA	0x41b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6SL_PAD_ECSPI1_SCLK__UART5_RX_DATA	0x41b0b1
+			MX6SL_PAD_ECSPI1_MOSI__UART5_TX_DATA	0x41b0b1
+			MX6SL_PAD_ECSPI1_MISO__UART5_RTS_B	0x4130b1
+			MX6SL_PAD_ECSPI1_SS0__UART5_CTS_B	0x4130b1
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x417059
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x410059
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x417059
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x417059
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x417059
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x417059
+			MX6SL_PAD_SD2_DAT4__SD2_DATA4		0x417059
+			MX6SL_PAD_SD2_DAT5__SD2_DATA5		0x417059
+			MX6SL_PAD_SD2_DAT6__SD2_DATA6		0x417059
+			MX6SL_PAD_SD2_DAT7__SD2_DATA7		0x417059
+			MX6SL_PAD_SD2_RST__SD2_RESET		0x417059
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhz-grp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x4170b9
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x4100b9
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x4170b9
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x4170b9
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x4170b9
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x4170b9
+			MX6SL_PAD_SD2_DAT4__SD2_DATA4		0x4170b9
+			MX6SL_PAD_SD2_DAT5__SD2_DATA5		0x4170b9
+			MX6SL_PAD_SD2_DAT6__SD2_DATA6		0x4170b9
+			MX6SL_PAD_SD2_DAT7__SD2_DATA7		0x4170b9
+			MX6SL_PAD_SD2_RST__SD2_RESET		0x4170b9
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhz-grp {
+		fsl,pins = <
+			MX6SL_PAD_SD2_CMD__SD2_CMD		0x4170f9
+			MX6SL_PAD_SD2_CLK__SD2_CLK		0x4100f9
+			MX6SL_PAD_SD2_DAT0__SD2_DATA0		0x4170f9
+			MX6SL_PAD_SD2_DAT1__SD2_DATA1		0x4170f9
+			MX6SL_PAD_SD2_DAT2__SD2_DATA2		0x4170f9
+			MX6SL_PAD_SD2_DAT3__SD2_DATA3		0x4170f9
+			MX6SL_PAD_SD2_DAT4__SD2_DATA4		0x4170f9
+			MX6SL_PAD_SD2_DAT5__SD2_DATA5		0x4170f9
+			MX6SL_PAD_SD2_DAT6__SD2_DATA6		0x4170f9
+			MX6SL_PAD_SD2_DAT7__SD2_DATA7		0x4170f9
+			MX6SL_PAD_SD2_RST__SD2_RESET		0x4170f9
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD		0x417059
+			MX6SL_PAD_SD3_CLK__SD3_CLK		0x410059
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0		0x417059
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1		0x417059
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2		0x417059
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3		0x417059
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhz-grp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD		0x4170b9
+			MX6SL_PAD_SD3_CLK__SD3_CLK		0x4100b9
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0		0x4170b9
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1		0x4170b9
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2		0x4170b9
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3		0x4170b9
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhz-grp {
+		fsl,pins = <
+			MX6SL_PAD_SD3_CMD__SD3_CMD		0x4170f9
+			MX6SL_PAD_SD3_CLK__SD3_CLK		0x4100f9
+			MX6SL_PAD_SD3_DAT0__SD3_DATA0		0x4170f9
+			MX6SL_PAD_SD3_DAT1__SD3_DATA1		0x4170f9
+			MX6SL_PAD_SD3_DAT2__SD3_DATA2		0x4170f9
+			MX6SL_PAD_SD3_DAT3__SD3_DATA3		0x4170f9
+		>;
 	};
 };
diff --git a/arch/arm/boot/dts/imx6sl.dtsi b/arch/arm/boot/dts/nxp/imx/imx6sl.dtsi
index c7d907c5c352..7381fb7f8912 100644
--- a/arch/arm/boot/dts/imx6sl.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6sl.dtsi
@@ -50,7 +50,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu@0 {
+		cpu0: cpu@0 {
 			compatible = "arm,cortex-a9";
 			device_type = "cpu";
 			reg = <0x0>;
@@ -61,10 +61,10 @@
 				<792000  1175000>,
 				<396000  975000>;
 			fsl,soc-operating-points =
-				/* ARM kHz      SOC-PU uV */
-				<996000         1225000>,
-				<792000         1175000>,
-				<396000         1175000>;
+				/* ARM kHz	SOC-PU uV */
+				<996000		1225000>,
+				<792000		1175000>,
+				<396000		1175000>;
 			clock-latency = <61036>; /* two CLK32 periods */
 			#cooling-cells = <2>;
 			clocks = <&clks IMX6SL_CLK_ARM>, <&clks IMX6SL_CLK_PLL2_PFD2>,
@@ -115,6 +115,9 @@
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6SL_CLK_OCRAM>;
 		};
 
@@ -222,7 +225,7 @@
 
 				uart5: serial@2018000 {
 					compatible = "fsl,imx6sl-uart",
-						   "fsl,imx6q-uart", "fsl,imx21-uart";
+						     "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02018000 0x4000>;
 					interrupts = <0 30 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6SL_CLK_UART>,
@@ -235,7 +238,7 @@
 
 				uart1: serial@2020000 {
 					compatible = "fsl,imx6sl-uart",
-						   "fsl,imx6q-uart", "fsl,imx21-uart";
+						     "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02020000 0x4000>;
 					interrupts = <0 26 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6SL_CLK_UART>,
@@ -248,7 +251,7 @@
 
 				uart2: serial@2024000 {
 					compatible = "fsl,imx6sl-uart",
-						   "fsl,imx6q-uart", "fsl,imx21-uart";
+						     "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02024000 0x4000>;
 					interrupts = <0 27 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6SL_CLK_UART>,
@@ -309,7 +312,7 @@
 
 				uart3: serial@2034000 {
 					compatible = "fsl,imx6sl-uart",
-						   "fsl,imx6q-uart", "fsl,imx21-uart";
+						     "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02034000 0x4000>;
 					interrupts = <0 28 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6SL_CLK_UART>,
@@ -322,7 +325,7 @@
 
 				uart4: serial@2038000 {
 					compatible = "fsl,imx6sl-uart",
-						   "fsl,imx6q-uart", "fsl,imx21-uart";
+						     "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02038000 0x4000>;
 					interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6SL_CLK_UART>,
@@ -375,7 +378,7 @@
 			};
 
 			gpt: timer@2098000 {
-				compatible = "fsl,imx6sl-gpt";
+				compatible = "fsl,imx6sl-gpt", "fsl,imx6dl-gpt";
 				reg = <0x02098000 0x4000>;
 				interrupts = <0 55 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6SL_CLK_GPT>,
@@ -543,8 +546,8 @@
 				reg_vdd3p0: regulator-3p0 {
 					compatible = "fsl,anatop-regulator";
 					regulator-name = "vdd3p0";
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <3150000>;
+					regulator-min-microvolt = <2625000>;
+					regulator-max-microvolt = <3400000>;
 					regulator-always-on;
 					anatop-reg-offset = <0x120>;
 					anatop-vol-bit-shift = <8>;
@@ -628,6 +631,7 @@
 					nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
 					nvmem-cell-names = "calib", "temp_grade";
 					clocks = <&clks IMX6SL_CLK_PLL3_USB_OTG>;
+					#thermal-sensor-cells = <0>;
 				};
 			};
 
@@ -636,6 +640,7 @@
 				reg = <0x020c9000 0x1000>;
 				interrupts = <0 44 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6SL_CLK_USBPHY1>;
+				phy-3p0-supply = <&reg_vdd3p0>;
 				fsl,anatop = <&anatop>;
 			};
 
@@ -644,6 +649,7 @@
 				reg = <0x020ca000 0x1000>;
 				interrupts = <0 45 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6SL_CLK_USBPHY2>;
+				phy-3p0-supply = <&reg_vdd3p0>;
 				fsl,anatop = <&anatop>;
 			};
 
@@ -711,7 +717,7 @@
 						#power-domain-cells = <0>;
 						power-supply = <&reg_pu>;
 						clocks = <&clks IMX6SL_CLK_GPU2D_OVG>,
-						         <&clks IMX6SL_CLK_GPU2D_PODF>;
+							 <&clks IMX6SL_CLK_GPU2D_PODF>;
 					};
 
 					pd_disp: power-domain@2 {
@@ -747,7 +753,7 @@
 				interrupts = <0 6 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
-			sdma: sdma@20ec000 {
+			sdma: dma-controller@20ec000 {
 				compatible = "fsl,imx6sl-sdma", "fsl,imx6q-sdma";
 				reg = <0x020ec000 0x4000>;
 				interrupts = <0 2 IRQ_TYPE_LEVEL_HIGH>;
@@ -856,7 +862,7 @@
 			};
 
 			usdhc1: mmc@2190000 {
-				compatible = "fsl,imx6sl-usdhc", "fsl,imx6q-usdhc";
+				compatible = "fsl,imx6sl-usdhc";
 				reg = <0x02190000 0x4000>;
 				interrupts = <0 22 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6SL_CLK_USDHC1>,
@@ -868,7 +874,7 @@
 			};
 
 			usdhc2: mmc@2194000 {
-				compatible = "fsl,imx6sl-usdhc", "fsl,imx6q-usdhc";
+				compatible = "fsl,imx6sl-usdhc";
 				reg = <0x02194000 0x4000>;
 				interrupts = <0 23 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6SL_CLK_USDHC2>,
@@ -880,7 +886,7 @@
 			};
 
 			usdhc3: mmc@2198000 {
-				compatible = "fsl,imx6sl-usdhc", "fsl,imx6q-usdhc";
+				compatible = "fsl,imx6sl-usdhc";
 				reg = <0x02198000 0x4000>;
 				interrupts = <0 24 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6SL_CLK_USDHC3>,
@@ -892,7 +898,7 @@
 			};
 
 			usdhc4: mmc@219c000 {
-				compatible = "fsl,imx6sl-usdhc", "fsl,imx6q-usdhc";
+				compatible = "fsl,imx6sl-usdhc";
 				reg = <0x0219c000 0x4000>;
 				interrupts = <0 25 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6SL_CLK_USDHC4>,
@@ -946,7 +952,7 @@
 				clocks = <&clks IMX6SL_CLK_DUMMY>;
 			};
 
-			weim: weim@21b8000 {
+			weim: memory-controller@21b8000 {
 				#address-cells = <2>;
 				#size-cells = <1>;
 				reg = <0x021b8000 0x4000>;
diff --git a/arch/arm/boot/dts/imx6sll-evk.dts b/arch/arm/boot/dts/nxp/imx/imx6sll-evk.dts
index 32b3d82fec53..814401486792 100644
--- a/arch/arm/boot/dts/imx6sll-evk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sll-evk.dts
@@ -26,7 +26,7 @@
 
 	backlight_display: backlight-display {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
 		status = "okay";
@@ -37,7 +37,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_led>;
 
-		user {
+		led-user {
 			label = "debug";
 			gpios = <&gpio2 4 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
@@ -109,6 +109,14 @@
 		enable-active-high;
 	};
 
+	reg_sd2_vmmc: regulator-sd2-vmmc {
+		compatible = "regulator-fixed";
+		regulator-name = "eMMC-VCCQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+	};
+
 	reg_sd3_vmmc: regulator-sd3-vmmc {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
@@ -149,7 +157,7 @@
 			"IN3R", "AMIC";
 		mux-int-port = <2>;
 		mux-ext-port = <3>;
-		hp-det-gpio = <&gpio4 24 GPIO_ACTIVE_LOW>;
+		hp-det-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
 	};
 };
 
@@ -306,10 +314,8 @@
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
-	status = "okay";
 };
 
 &snvs_poweroff {
@@ -343,6 +349,17 @@
 	status = "okay";
 };
 
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	vqmmc-supply = <&reg_sd2_vmmc>;
+	status = "okay";
+};
+
 &usbotg1 {
 	vbus-supply = <&reg_usb_otg1_vbus>;
 	pinctrl-names = "default";
@@ -444,7 +461,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_100mhz: usdhc1grp_100mhz {
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
 		fsl,pins = <
 			MX6SLL_PAD_SD1_CMD__SD1_CMD	0x170b9
 			MX6SLL_PAD_SD1_CLK__SD1_CLK	0x130b9
@@ -455,7 +472,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_200mhz: usdhc1grp_200mhz {
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
 		fsl,pins = <
 			MX6SLL_PAD_SD1_CMD__SD1_CMD	0x170f9
 			MX6SLL_PAD_SD1_CLK__SD1_CLK	0x130f9
@@ -466,6 +483,54 @@
 		>;
 	};
 
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6SLL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6SLL_PAD_SD2_CLK__SD2_CLK		0x13059
+			MX6SLL_PAD_SD2_DATA0__SD2_DATA0		0x17059
+			MX6SLL_PAD_SD2_DATA1__SD2_DATA1		0x17059
+			MX6SLL_PAD_SD2_DATA2__SD2_DATA2		0x17059
+			MX6SLL_PAD_SD2_DATA3__SD2_DATA3		0x17059
+			MX6SLL_PAD_SD2_DATA4__SD2_DATA4		0x17059
+			MX6SLL_PAD_SD2_DATA5__SD2_DATA5		0x17059
+			MX6SLL_PAD_SD2_DATA6__SD2_DATA6		0x17059
+			MX6SLL_PAD_SD2_DATA7__SD2_DATA7		0x17059
+			MX6SLL_PAD_GPIO4_IO21__SD2_STROBE	0x13059
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6SLL_PAD_SD2_CMD__SD2_CMD		0x170b9
+			MX6SLL_PAD_SD2_CLK__SD2_CLK		0x130b9
+			MX6SLL_PAD_SD2_DATA0__SD2_DATA0		0x170b9
+			MX6SLL_PAD_SD2_DATA1__SD2_DATA1		0x170b9
+			MX6SLL_PAD_SD2_DATA2__SD2_DATA2		0x170b9
+			MX6SLL_PAD_SD2_DATA3__SD2_DATA3		0x170b9
+			MX6SLL_PAD_SD2_DATA4__SD2_DATA4		0x170b9
+			MX6SLL_PAD_SD2_DATA5__SD2_DATA5		0x170b9
+			MX6SLL_PAD_SD2_DATA6__SD2_DATA6		0x170b9
+			MX6SLL_PAD_SD2_DATA7__SD2_DATA7		0x170b9
+			MX6SLL_PAD_GPIO4_IO21__SD2_STROBE	0x130b9
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6SLL_PAD_SD2_CMD__SD2_CMD		0x170f9
+			MX6SLL_PAD_SD2_CLK__SD2_CLK		0x130f9
+			MX6SLL_PAD_SD2_DATA0__SD2_DATA0		0x170f9
+			MX6SLL_PAD_SD2_DATA1__SD2_DATA1		0x170f9
+			MX6SLL_PAD_SD2_DATA2__SD2_DATA2		0x170f9
+			MX6SLL_PAD_SD2_DATA3__SD2_DATA3		0x170f9
+			MX6SLL_PAD_SD2_DATA4__SD2_DATA4		0x170f9
+			MX6SLL_PAD_SD2_DATA5__SD2_DATA5		0x170f9
+			MX6SLL_PAD_SD2_DATA6__SD2_DATA6		0x170f9
+			MX6SLL_PAD_SD2_DATA7__SD2_DATA7		0x170f9
+			MX6SLL_PAD_GPIO4_IO21__SD2_STROBE	0x130f9
+		>;
+	};
+
 	pinctrl_usbotg1: usbotg1grp {
 		fsl,pins = <
 			MX6SLL_PAD_EPDC_PWR_COM__USB_OTG1_ID 0x17059
@@ -484,7 +549,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_100mhz: usdhc3grp_100mhz {
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
 		fsl,pins = <
 			MX6SLL_PAD_SD3_CMD__SD3_CMD		0x170a1
 			MX6SLL_PAD_SD3_CLK__SD3_CLK		0x130a1
@@ -496,7 +561,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_200mhz: usdhc3grp_200mhz {
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
 		fsl,pins = <
 			MX6SLL_PAD_SD3_CMD__SD3_CMD		0x170e9
 			MX6SLL_PAD_SD3_CLK__SD3_CLK		0x130f9
diff --git a/arch/arm/boot/dts/nxp/imx/imx6sll-kobo-clara2e-a.dts b/arch/arm/boot/dts/nxp/imx/imx6sll-kobo-clara2e-a.dts
new file mode 100644
index 000000000000..33756d6de7aa
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6sll-kobo-clara2e-a.dts
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: (GPL-2.0)
+/*
+ * Device tree for the Kobo Clara 2E rev A ebook reader
+ *
+ * Name on mainboard is: 37NB-E60K2M+4A2
+ * Serials start with: E60K2M (a number also seen in
+ * vendor kernel sources)
+ *
+ * Copyright 2024 Andreas Kemnade
+ */
+
+/dts-v1/;
+
+#include "imx6sll-kobo-clara2e-common.dtsi"
+
+/ {
+	model = "Kobo Clara 2E";
+	compatible = "kobo,clara2e-b", "kobo,clara2e", "fsl,imx6sll";
+};
+
+&i2c2 {
+	/* EPD PMIC SY7636 at 0x62 */
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6sll-kobo-clara2e-b.dts b/arch/arm/boot/dts/nxp/imx/imx6sll-kobo-clara2e-b.dts
new file mode 100644
index 000000000000..f81aeacf5142
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6sll-kobo-clara2e-b.dts
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: (GPL-2.0)
+/*
+ * Device tree for the Kobo Clara 2E rev B ebook reader
+ *
+ * Name on mainboard is: 37NB-E60K2M+4B0
+ * Serials start with: E60K2M (a number also seen in
+ * vendor kernel sources)
+ *
+ * Copyright 2024 Andreas Kemnade
+ */
+
+/dts-v1/;
+
+#include "imx6sll-kobo-clara2e-common.dtsi"
+
+/ {
+	model = "Kobo Clara 2E";
+	compatible = "kobo,clara2e-b", "kobo,clara2e", "fsl,imx6sll";
+};
+
+&i2c2 {
+	/* EPD PMIC JD9930 at 0x18 */
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6sll-kobo-clara2e-common.dtsi b/arch/arm/boot/dts/nxp/imx/imx6sll-kobo-clara2e-common.dtsi
new file mode 100644
index 000000000000..6f2deb366e02
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6sll-kobo-clara2e-common.dtsi
@@ -0,0 +1,511 @@
+// SPDX-License-Identifier: (GPL-2.0)
+/*
+ * Common part for Kobo Clara 2e device tree
+ * Copyright 2024 Andreas Kemnade
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "imx6sll.dtsi"
+
+/ {
+	aliases {
+		mmc0 = &usdhc2;
+		mmc1 = &usdhc3;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		key-cover {
+			label = "Cover";
+			gpios = <&gpio4 23 GPIO_ACTIVE_LOW>;
+			linux,code = <SW_LID>;
+			linux,input-type = <EV_SW>;
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_led>;
+
+		led {
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&gpio4 17 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "timer";
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reg_wifi: regulator-wifi {
+		compatible = "regulator-fixed";
+		regulator-name = "SD3_SPWR";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		gpio = <&gpio4 29 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&clks {
+	assigned-clocks = <&clks IMX6SLL_CLK_PLL4_AUDIO_DIV>;
+	assigned-clock-rates = <393216000>;
+};
+
+&cpu0 {
+	arm-supply = <&buck1>;
+	soc-supply = <&buck2>;
+};
+
+&i2c1 {
+	pinctrl-names = "default","sleep";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_sleep>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	/* backlight aw99703 at 0x36 */
+};
+
+&i2c2 {
+	pinctrl-names = "default","sleep";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_sleep>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	/* backlight aw99703 at 0x36 */
+
+	touchscreen@38 {
+		compatible = "focaltech,ft5426";
+		reg = <0x38>;
+		pinctrl-names = "default", "suspend";
+		pinctrl-0 = <&pinctrl_touch_gpio>;
+		pinctrl-1 = <&pinctrl_touch_gpio_sleep>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&gpio4 18 GPIO_ACTIVE_LOW>;
+		touchscreen-size-x = <1072>;
+		touchscreen-size-y = <1448>;
+		touchscreen-swapped-x-y;
+	};
+};
+
+&i2c3 {
+	/* Bus seems to be in bad state after boot, allow full recovery */
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	pinctrl-1 = <&pinctrl_i2c3_gpio>;
+	sda-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+	scl-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	pmic@4b {
+		compatible = "rohm,bd71879", "rohm,bd71828";
+		reg = <0x4b>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_bd71828>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+		system-power-controller;
+		clocks = <&clks 0>;
+		#clock-cells = <0>;
+		clock-output-names = "bd71828-32k-out";
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-reserved-ranges = <0 1>, <2 1>;
+
+		/* charge sense resistor is 30 milli-ohm */
+
+		regulators {
+			LDO1 {
+				name = "LDO1";
+				regulator-name = "ldo1";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			LDO2 {
+				name = "LDO2";
+				regulator-name = "ldo2";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			LDO3 {
+				name = "LDO3";
+				regulator-name = "ldo3";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			ldo4: LDO4 {
+				name = "LDO4";
+				regulator-name = "ldo4";
+				regulator-always-on;
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+			};
+
+			LDO5 {
+				name = "LDO5";
+				regulator-name = "ldo5";
+				regulator-always-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			LDO6 {
+				name = "LDO6";
+				regulator-name = "ldo6";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			LDO7 {
+				name = "LDO7";
+				regulator-name = "ldo7";
+				regulator-always-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+			};
+
+			buck1: BUCK1 {
+				name = "BUCK1";
+				regulator-name = "buck1";
+				regulator-always-on;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-boot-on;
+			};
+
+			buck2: BUCK2 {
+				name = "BUCK2";
+				regulator-name = "buck2";
+				regulator-always-on;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <2000000>;
+				regulator-boot-on;
+			};
+
+			BUCK3 {
+				name = "BUCK3";
+				regulator-name = "buck3";
+				regulator-always-on;
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+			};
+
+			BUCK4 {
+				name = "BUCK4";
+				regulator-name = "buck4";
+				regulator-always-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-boot-on;
+			};
+
+			BUCK5 {
+				name = "BUCK5";
+				regulator-name = "buck5";
+				regulator-always-on;
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+			};
+
+			BUCK6 {
+				name = "BUCK6";
+				regulator-name = "buck6";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <2000000>;
+			};
+
+			BUCK7 {
+				name = "BUCK7";
+				regulator-name = "buck7";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <2000000>;
+			};
+		};
+	};
+};
+
+&iomuxc {
+	pinctrl_bd71828: bd71828-gpiogrp {
+		fsl,pins = <
+			MX6SLL_PAD_KEY_COL0__GPIO3_IO24		0x1b8b1
+			MX6SLL_PAD_GPIO4_IO19__GPIO4_IO19	0x1b8b1
+		>;
+	};
+
+	pinctrl_gpio_keys: gpio-keysgrp {
+		fsl,pins = <
+			MX6SLL_PAD_GPIO4_IO25__GPIO4_IO25	0x17059	/* PWR_SW */
+			MX6SLL_PAD_GPIO4_IO23__GPIO4_IO23	0x17059	/* HALL_EN */
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6SLL_PAD_I2C1_SCL__I2C1_SCL	0x4001f8b1
+			MX6SLL_PAD_I2C1_SDA__I2C1_SDA	0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c1_sleep: i2c1-sleepgrp {
+		fsl,pins = <
+			MX6SLL_PAD_I2C1_SCL__I2C1_SCL	0x400108b1
+			MX6SLL_PAD_I2C1_SDA__I2C1_SDA	0x400108b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6SLL_PAD_I2C2_SCL__I2C2_SCL	0x4001f8b1
+			MX6SLL_PAD_I2C2_SDA__I2C2_SDA	0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c2_sleep: i2c2-sleepgrp {
+		fsl,pins = <
+			MX6SLL_PAD_I2C2_SCL__I2C2_SCL	0x400108b1
+			MX6SLL_PAD_I2C2_SDA__I2C2_SDA	0x400108b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6SLL_PAD_REF_CLK_24M__I2C3_SCL 0x4001f8b1
+			MX6SLL_PAD_REF_CLK_32K__I2C3_SDA 0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c3_gpio: i2c3-gpiogrp {
+		fsl,pins = <
+			MX6SLL_PAD_REF_CLK_24M__GPIO3_IO21 0x4001f8b1
+			MX6SLL_PAD_REF_CLK_32K__GPIO3_IO22 0x4001f8b1
+		>;
+	};
+
+	pinctrl_led: ledgrp {
+		fsl,pins = <
+			MX6SLL_PAD_GPIO4_IO17__GPIO4_IO17 0x10059
+		>;
+	};
+
+	pinctrl_touch_gpio: touch-gpiogrp {
+		fsl,pins = <
+			MX6SLL_PAD_GPIO4_IO24__GPIO4_IO24	0x17059 /* TP_INT */
+			MX6SLL_PAD_GPIO4_IO18__GPIO4_IO18	0x10059 /* TP_RST */
+		>;
+	};
+
+	pinctrl_touch_gpio_sleep: touch-gpio-sleepgrp {
+		fsl,pins = <
+			MX6SLL_PAD_GPIO4_IO24__GPIO4_IO24	0x10059 /* TP_INT */
+			MX6SLL_PAD_GPIO4_IO18__GPIO4_IO18	0x10059 /* TP_RST */
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6SLL_PAD_UART1_TXD__UART1_DCE_TX 0x1b0b1
+			MX6SLL_PAD_UART1_RXD__UART1_DCE_RX 0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6SLL_PAD_LCD_ENABLE__UART2_DCE_RX	0x41b0b1
+			MX6SLL_PAD_LCD_HSYNC__UART2_DCE_TX	0x41b0b1
+			MX6SLL_PAD_LCD_VSYNC__UART2_DCE_RTS	0x41b0b1
+			MX6SLL_PAD_LCD_RESET__UART2_DCE_CTS	0x41b0b1
+		>;
+	};
+
+	pinctrl_uart2_sleep: uart2-sleepgrp {
+		fsl,pins = <
+			MX6SLL_PAD_LCD_ENABLE__GPIO2_IO16	0x10059
+			MX6SLL_PAD_LCD_HSYNC__GPIO2_IO17	0x10059
+			MX6SLL_PAD_LCD_VSYNC__GPIO2_IO18	0x10059
+			MX6SLL_PAD_LCD_RESET__GPIO2_IO19	0x10059
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = <
+			MX6SLL_PAD_EPDC_PWR_COM__USB_OTG1_ID 0x17059
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6SLL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6SLL_PAD_SD2_CLK__SD2_CLK		0x13059
+			MX6SLL_PAD_SD2_DATA0__SD2_DATA0		0x17059
+			MX6SLL_PAD_SD2_DATA1__SD2_DATA1		0x17059
+			MX6SLL_PAD_SD2_DATA2__SD2_DATA2		0x17059
+			MX6SLL_PAD_SD2_DATA3__SD2_DATA3		0x17059
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6SLL_PAD_SD2_CMD__SD2_CMD		0x170b9
+			MX6SLL_PAD_SD2_CLK__SD2_CLK		0x130b9
+			MX6SLL_PAD_SD2_DATA0__SD2_DATA0		0x170b9
+			MX6SLL_PAD_SD2_DATA1__SD2_DATA1		0x170b9
+			MX6SLL_PAD_SD2_DATA2__SD2_DATA2		0x170b9
+			MX6SLL_PAD_SD2_DATA3__SD2_DATA3		0x170b9
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6SLL_PAD_SD2_CMD__SD2_CMD		0x170f9
+			MX6SLL_PAD_SD2_CLK__SD2_CLK		0x130f9
+			MX6SLL_PAD_SD2_DATA0__SD2_DATA0		0x170f9
+			MX6SLL_PAD_SD2_DATA1__SD2_DATA1		0x170f9
+			MX6SLL_PAD_SD2_DATA2__SD2_DATA2		0x170f9
+			MX6SLL_PAD_SD2_DATA3__SD2_DATA3		0x170f9
+		>;
+	};
+
+	pinctrl_usdhc2_sleep: usdhc2-sleepgrp {
+		fsl,pins = <
+			MX6SLL_PAD_SD2_CMD__GPIO5_IO04		0x100f9
+			MX6SLL_PAD_SD2_CLK__GPIO5_IO05		0x100f9
+			MX6SLL_PAD_SD2_DATA0__GPIO5_IO01	0x100f9
+			MX6SLL_PAD_SD2_DATA1__GPIO4_IO30	0x100f9
+			MX6SLL_PAD_SD2_DATA2__GPIO5_IO03	0x100f9
+			MX6SLL_PAD_SD2_DATA3__GPIO4_IO28	0x100f9
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6SLL_PAD_SD3_CMD__SD3_CMD	0x11059
+			MX6SLL_PAD_SD3_CLK__SD3_CLK	0x11059
+			MX6SLL_PAD_SD3_DATA0__SD3_DATA0	0x11059
+			MX6SLL_PAD_SD3_DATA1__SD3_DATA1	0x11059
+			MX6SLL_PAD_SD3_DATA2__SD3_DATA2	0x11059
+			MX6SLL_PAD_SD3_DATA3__SD3_DATA3	0x11059
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX6SLL_PAD_SD3_CMD__SD3_CMD	0x170b9
+			MX6SLL_PAD_SD3_CLK__SD3_CLK	0x170b9
+			MX6SLL_PAD_SD3_DATA0__SD3_DATA0	0x170b9
+			MX6SLL_PAD_SD3_DATA1__SD3_DATA1	0x170b9
+			MX6SLL_PAD_SD3_DATA2__SD3_DATA2	0x170b9
+			MX6SLL_PAD_SD3_DATA3__SD3_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX6SLL_PAD_SD3_CMD__SD3_CMD	0x170f9
+			MX6SLL_PAD_SD3_CLK__SD3_CLK	0x170f9
+			MX6SLL_PAD_SD3_DATA0__SD3_DATA0	0x170f9
+			MX6SLL_PAD_SD3_DATA1__SD3_DATA1	0x170f9
+			MX6SLL_PAD_SD3_DATA2__SD3_DATA2	0x170f9
+			MX6SLL_PAD_SD3_DATA3__SD3_DATA3	0x170f9
+		>;
+	};
+
+	pinctrl_usdhc3_sleep: usdhc3-sleepgrp {
+		fsl,pins = <
+			MX6SLL_PAD_SD3_CMD__GPIO5_IO21	0x100c1
+			MX6SLL_PAD_SD3_CLK__GPIO5_IO18	0x100c1
+			MX6SLL_PAD_SD3_DATA0__GPIO5_IO19	0x100c1
+			MX6SLL_PAD_SD3_DATA1__GPIO5_IO20	0x100c1
+			MX6SLL_PAD_SD3_DATA2__GPIO5_IO16	0x100c1
+			MX6SLL_PAD_SD3_DATA3__GPIO5_IO17	0x100c1
+		>;
+	};
+
+	pinctrl_wifi_power: wifi-powergrp {
+		fsl,pins = <
+			MX6SLL_PAD_SD2_DATA6__GPIO4_IO29	0x10059
+		>;
+	};
+};
+
+&snvs_rtc {
+	/* we are using the rtc in the pmic, not disabled in imx6sll.dtsi */
+	status = "disabled";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_uart2>;
+	pinctrl-1 = <&pinctrl_uart2_sleep>;
+	status = "okay";
+
+	/* requires LDO4 + power enable gpio */
+	bluetooth {
+		compatible = "nxp,88w8987-bt";
+		fw-init-baudrate = <1500000>;
+	};
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
+	disable-over-current;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz","sleep";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc2_sleep>;
+	non-removable;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz","sleep";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	pinctrl-3 = <&pinctrl_usdhc3_sleep>;
+	/* card requires also ldo4 */
+	vmmc-supply = <&reg_wifi>;
+	cap-power-off-card;
+	non-removable;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6sll-kobo-clarahd.dts b/arch/arm/boot/dts/nxp/imx/imx6sll-kobo-clarahd.dts
index 90b32f5eb529..18c9ac8f7560 100644
--- a/arch/arm/boot/dts/imx6sll-kobo-clarahd.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sll-kobo-clarahd.dts
@@ -62,6 +62,13 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hog>;
 
+	pinctrl_cyttsp5_gpio: cyttsp5-gpiogrp {
+		fsl,pins = <
+			MX6SLL_PAD_SD1_DATA3__GPIO5_IO06                0x17059 /* TP_INT */
+			MX6SLL_PAD_SD1_DATA2__GPIO5_IO13                0x10059 /* TP_RST */
+		>;
+	};
+
 	pinctrl_gpio_keys: gpio-keysgrp {
 		fsl,pins = <
 			MX6SLL_PAD_SD1_DATA1__GPIO5_IO08	0x17059	/* PWR_SW */
@@ -114,7 +121,7 @@
 		>;
 	};
 
-	pinctrl_i2c1_sleep: i2c1grp-sleep {
+	pinctrl_i2c1_sleep: i2c1sleep-grp {
 		fsl,pins = <
 			MX6SLL_PAD_I2C1_SCL__I2C1_SCL	0x400108b1
 			MX6SLL_PAD_I2C1_SDA__I2C1_SDA	0x400108b1
@@ -128,7 +135,7 @@
 		>;
 	};
 
-	pinctrl_i2c2_sleep: i2c2grp-sleep {
+	pinctrl_i2c2_sleep: i2c2sleep-grp {
 		fsl,pins = <
 			MX6SLL_PAD_I2C2_SCL__I2C2_SCL	0x400108b1
 			MX6SLL_PAD_I2C2_SDA__I2C2_SDA	0x400108b1
@@ -193,7 +200,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_100mhz: usdhc2grp-100mhz {
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
 		fsl,pins = <
 			MX6SLL_PAD_SD2_CMD__SD2_CMD		0x170b9
 			MX6SLL_PAD_SD2_CLK__SD2_CLK		0x130b9
@@ -204,7 +211,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_200mhz: usdhc2grp-200mhz {
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
 		fsl,pins = <
 			MX6SLL_PAD_SD2_CMD__SD2_CMD		0x170f9
 			MX6SLL_PAD_SD2_CLK__SD2_CLK		0x130f9
@@ -215,7 +222,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_sleep: usdhc2grp-sleep {
+	pinctrl_usdhc2_sleep: usdhc2sleep-grp {
 		fsl,pins = <
 			MX6SLL_PAD_SD2_CMD__GPIO5_IO04		0x100f9
 			MX6SLL_PAD_SD2_CLK__GPIO5_IO05		0x100f9
@@ -237,7 +244,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_100mhz: usdhc3grp-100mhz {
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
 		fsl,pins = <
 			MX6SLL_PAD_SD3_CMD__SD3_CMD	0x170b9
 			MX6SLL_PAD_SD3_CLK__SD3_CLK	0x170b9
@@ -248,7 +255,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_200mhz: usdhc3grp-200mhz {
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
 		fsl,pins = <
 			MX6SLL_PAD_SD3_CMD__SD3_CMD	0x170f9
 			MX6SLL_PAD_SD3_CLK__SD3_CLK	0x170f9
@@ -259,7 +266,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_sleep: usdhc3grp-sleep {
+	pinctrl_usdhc3_sleep: usdhc3sleep-grp {
 		fsl,pins = <
 			MX6SLL_PAD_SD3_CMD__GPIO5_IO21	0x100c1
 			MX6SLL_PAD_SD3_CLK__GPIO5_IO18	0x100c1
diff --git a/arch/arm/boot/dts/imx6sll-kobo-librah2o.dts b/arch/arm/boot/dts/nxp/imx/imx6sll-kobo-librah2o.dts
index a8b0e88064d9..660620d226f7 100644
--- a/arch/arm/boot/dts/imx6sll-kobo-librah2o.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sll-kobo-librah2o.dts
@@ -62,6 +62,13 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hog>;
 
+	pinctrl_cyttsp5_gpio: cyttsp5-gpiogrp {
+		fsl,pins = <
+			MX6SLL_PAD_GPIO4_IO24__GPIO4_IO24	0x17059 /* TP_INT */
+			MX6SLL_PAD_GPIO4_IO18__GPIO4_IO18	0x10059 /* TP_RST */
+		>;
+	};
+
 	pinctrl_gpio_keys: gpio-keysgrp {
 		fsl,pins = <
 			MX6SLL_PAD_GPIO4_IO25__GPIO4_IO25	0x17059	/* PWR_SW */
@@ -114,7 +121,7 @@
 		>;
 	};
 
-	pinctrl_i2c1_sleep: i2c1grp-sleep {
+	pinctrl_i2c1_sleep: i2c1sleep-grp {
 		fsl,pins = <
 			MX6SLL_PAD_I2C1_SCL__I2C1_SCL   0x400108b1
 			MX6SLL_PAD_I2C1_SDA__I2C1_SDA   0x400108b1
@@ -128,7 +135,7 @@
 		>;
 	};
 
-	pinctrl_i2c2_sleep: i2c2grp-sleep {
+	pinctrl_i2c2_sleep: i2c2sleep-grp {
 		fsl,pins = <
 			MX6SLL_PAD_I2C2_SCL__I2C2_SCL   0x400108b1
 			MX6SLL_PAD_I2C2_SDA__I2C2_SDA   0x400108b1
diff --git a/arch/arm/boot/dts/imx6sll-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx6sll-pinfunc.h
index 713a346f4c89..713a346f4c89 100644
--- a/arch/arm/boot/dts/imx6sll-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx6sll-pinfunc.h
diff --git a/arch/arm/boot/dts/imx6sll.dtsi b/arch/arm/boot/dts/nxp/imx/imx6sll.dtsi
index d4a000c3dde7..704870e8c10c 100644
--- a/arch/arm/boot/dts/imx6sll.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6sll.dtsi
@@ -115,6 +115,9 @@
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 		};
 
 		intc: interrupt-controller@a01000 {
@@ -170,7 +173,7 @@
 						      "rxtx1", "rxtx2",
 						      "rxtx3", "rxtx4",
 						      "rxtx5", "rxtx6",
-						      "rxtx7", "dma";
+						      "rxtx7", "spba";
 					status = "disabled";
 				};
 
@@ -306,7 +309,7 @@
 					reg = <0x02034000 0x4000>;
 					interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
 					dmas = <&sdma 29 4 0>, <&sdma 30 4 0>;
-					dma-name = "rx", "tx";
+					dma-names = "rx", "tx";
 					clocks = <&clks IMX6SLL_CLK_UART3_IPG>,
 						 <&clks IMX6SLL_CLK_UART3_SERIAL>;
 					clock-names = "ipg", "per";
@@ -355,7 +358,7 @@
 			};
 
 			gpt1: timer@2098000 {
-				compatible = "fsl,imx6sl-gpt";
+				compatible = "fsl,imx6sl-gpt", "fsl,imx6dl-gpt";
 				reg = <0x02098000 0x4000>;
 				interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6SLL_CLK_GPT_BUS>,
@@ -504,12 +507,9 @@
 				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
-				#address-cells = <1>;
-				#size-cells = <0>;
 
-				reg_3p0: regulator-3p0@20c8120 {
+				reg_3p0: regulator-3p0 {
 					compatible = "fsl,anatop-regulator";
-					reg = <0x20c8120>;
 					regulator-name = "vdd3p0";
 					regulator-min-microvolt = <2625000>;
 					regulator-max-microvolt = <3400000>;
@@ -522,7 +522,7 @@
 					anatop-enable-bit = <0>;
 				};
 
-				tempmon: temperature-sensor {
+				tempmon: tempmon {
 					compatible = "fsl,imx6sll-tempmon", "fsl,imx6sx-tempmon";
 					interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-parent = <&gpc>;
@@ -530,6 +530,7 @@
 					nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
 					nvmem-cell-names = "calib", "temp_grade";
 					clocks = <&clks IMX6SLL_CLK_PLL3_USB_OTG>;
+					#thermal-sensor-cells = <0>;
 				};
 			};
 
@@ -549,7 +550,7 @@
 				reg = <0x020ca000 0x1000>;
 				interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6SLL_CLK_USBPHY2>;
-				phy-reg_3p0-supply = <&reg_3p0>;
+				phy-3p0-supply = <&reg_3p0>;
 				fsl,anatop = <&anatop>;
 			};
 
@@ -598,6 +599,18 @@
 				#interrupt-cells = <3>;
 				interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-parent = <&intc>;
+				clocks = <&clks IMX6SLL_CLK_IPG>;
+				clock-names = "ipg";
+
+				pgc {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					power-domain@0 {
+						reg = <0>;
+						#power-domain-cells = <0>;
+					};
+				};
 			};
 
 			iomuxc: pinctrl@20e0000 {
@@ -680,7 +693,6 @@
 				clocks = <&clks IMX6SLL_CLK_USBOH3>;
 				fsl,usbphy = <&usbphy1>;
 				fsl,usbmisc = <&usbmisc 0>;
-				fsl,anatop = <&anatop>;
 				ahb-burst-config = <0x0>;
 				tx-burst-size-dword = <0x10>;
 				rx-burst-size-dword = <0x10>;
diff --git a/arch/arm/boot/dts/imx6sx-nitrogen6sx.dts b/arch/arm/boot/dts/nxp/imx/imx6sx-nitrogen6sx.dts
index 66af78e83b70..1c1515a854c8 100644
--- a/arch/arm/boot/dts/imx6sx-nitrogen6sx.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-nitrogen6sx.dts
@@ -18,7 +18,7 @@
 
 	backlight-lvds {
 		compatible = "pwm-backlight";
-		pwms = <&pwm4 0 5000000>;
+		pwms = <&pwm4 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
 		power-supply = <&reg_3p3v>;
@@ -72,7 +72,6 @@
 		pinctrl-0 = <&pinctrl_reg_wlan>;
 		compatible = "regulator-fixed";
 		clocks = <&clks IMX6SX_CLK_CKO>;
-		clock-names = "slow";
 		regulator-name = "wlan-en";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
@@ -84,7 +83,7 @@
 	sound {
 		compatible = "fsl,imx-audio-sgtl5000";
 		model = "imx6sx-nitrogen6sx-sgtl5000";
-		cpu-dai = <&ssi1>;
+		ssi-controller = <&ssi1>;
 		audio-codec = <&codec>;
 		audio-routing =
 			"MIC_IN", "Mic Jack",
@@ -107,7 +106,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "microchip,sst25vf016b";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
@@ -196,6 +195,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_sgtl5000>;
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6SX_CLK_CKO2>;
 		VDDA-supply = <&reg_1p8v>;
 		VDDIO-supply = <&reg_1p8v>;
@@ -229,10 +229,8 @@
 };
 
 &pwm4 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
-	status = "okay";
 };
 
 &ssi1 {
diff --git a/arch/arm/boot/dts/imx6sx-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx6sx-pinfunc.h
index f4dc46207954..f4dc46207954 100644
--- a/arch/arm/boot/dts/imx6sx-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-pinfunc.h
diff --git a/arch/arm/boot/dts/imx6sx-sabreauto.dts b/arch/arm/boot/dts/nxp/imx/imx6sx-sabreauto.dts
index 83ee97252ff1..033700e052b3 100644
--- a/arch/arm/boot/dts/imx6sx-sabreauto.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-sabreauto.dts
@@ -20,7 +20,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_led>;
 
-		user {
+		led-user {
 			label = "debug";
 			gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
@@ -97,11 +97,16 @@
 			"AIN2R", "Line In Jack";
 	};
 
+	spdif_in: spdif-in {
+		compatible = "linux,spdif-dir";
+		#sound-dai-cells = <0>;
+	};
+
 	sound-spdif {
 		compatible = "fsl,imx-audio-spdif";
 		model = "imx-spdif";
-		spdif-controller = <&spdif>;
-		spdif-in;
+		audio-cpu = <&spdif>;
+		audio-codec = <&spdif_in>;
 	};
 };
 
@@ -328,7 +333,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_100mhz: usdhc3grp-100mhz {
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
 		fsl,pins = <
 			MX6SX_PAD_SD3_CMD__USDHC3_CMD		0x170b9
 			MX6SX_PAD_SD3_CLK__USDHC3_CLK		0x100b9
@@ -343,7 +348,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_200mhz: usdhc3grp-200mhz {
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
 		fsl,pins = <
 			MX6SX_PAD_SD3_CMD__USDHC3_CMD		0x170f9
 			MX6SX_PAD_SD3_CLK__USDHC3_CLK		0x100f9
diff --git a/arch/arm/boot/dts/imx6sx-sdb-mqs.dts b/arch/arm/boot/dts/nxp/imx/imx6sx-sdb-mqs.dts
index a4ab2d3e960c..a4ab2d3e960c 100644
--- a/arch/arm/boot/dts/imx6sx-sdb-mqs.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-sdb-mqs.dts
diff --git a/arch/arm/boot/dts/imx6sx-sdb-reva.dts b/arch/arm/boot/dts/nxp/imx/imx6sx-sdb-reva.dts
index dce5dcf96c25..48f19dede467 100644
--- a/arch/arm/boot/dts/imx6sx-sdb-reva.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-sdb-reva.dts
@@ -15,7 +15,7 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
 		reg = <0x08>;
 
@@ -123,7 +123,7 @@
 	pinctrl-0 = <&pinctrl_qspi2>;
 	status = "okay";
 
-	flash0: s25fl128s@0 {
+	flash0: flash@0 {
 		reg = <0>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -133,7 +133,7 @@
 		spi-tx-bus-width = <4>;
 	};
 
-	flash1: s25fl128s@2 {
+	flash1: flash@2 {
 		reg = <2>;
 		#address-cells = <1>;
 		#size-cells = <1>;
diff --git a/arch/arm/boot/dts/imx6sx-sdb-sai.dts b/arch/arm/boot/dts/nxp/imx/imx6sx-sdb-sai.dts
index 1c4eacd68e1b..1c4eacd68e1b 100644
--- a/arch/arm/boot/dts/imx6sx-sdb-sai.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-sdb-sai.dts
diff --git a/arch/arm/boot/dts/imx6sx-sdb.dts b/arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dts
index 99f4cf777a38..e05a1be5553c 100644
--- a/arch/arm/boot/dts/imx6sx-sdb.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dts
@@ -14,7 +14,7 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze200";
 		reg = <0x08>;
 
@@ -108,7 +108,7 @@
 	pinctrl-0 = <&pinctrl_qspi2>;
 	status = "okay";
 
-	flash0: n25q256a@0 {
+	flash0: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q256a", "jedec,spi-nor";
@@ -118,7 +118,7 @@
 		reg = <0>;
 	};
 
-	flash1: n25q256a@2 {
+	flash1: flash@2 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q256a", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtsi b/arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtsi
new file mode 100644
index 000000000000..c7aeb99d8f00
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtsi
@@ -0,0 +1,719 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2014 Freescale Semiconductor, Inc.
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "imx6sx.dtsi"
+
+/ {
+	model = "Freescale i.MX6 SoloX SDB Board";
+	compatible = "fsl,imx6sx-sdb", "fsl,imx6sx";
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+
+	backlight_display: backlight-display {
+		compatible = "pwm-backlight";
+		pwms = <&pwm3 0 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			wakeup-source;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			wakeup-source;
+		};
+	};
+
+	vcc_sd3: regulator-vcc-sd3 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_vcc_sd3>;
+		regulator-name = "VCC_SD3";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb_otg1>;
+		regulator-name = "usb_otg1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usb_otg2_vbus: regulator-usb-otg2-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb_otg2>;
+		regulator-name = "usb_otg2_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_psu_5v: regulator-psu-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "PSU-5V0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_lcd_3v3: regulator-lcd-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-3v3";
+		gpio = <&gpio3 27 0>;
+		enable-active-high;
+	};
+
+	reg_peri_3v3: regulator-peri-3v3 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_peri_3v3>;
+		regulator-name = "peri_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio4 16 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	reg_enet_3v3: regulator-enet-3v3 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_enet_3v3>;
+		regulator-name = "enet_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 6 GPIO_ACTIVE_LOW>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_pcie_gpio: regulator-pcie-gpio {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pcie_reg>;
+		regulator-name = "MPCIE_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_lcd_5v: regulator-lcd-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_can_en: regulator-can-en {
+		compatible = "regulator-fixed";
+		regulator-name = "can-en";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_can_stby: regulator-can-stby {
+		compatible = "regulator-fixed";
+		regulator-name = "can-stby";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	sound {
+		compatible = "fsl,imx6sx-sdb-wm8962", "fsl,imx-audio-wm8962";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_hp>;
+		model = "wm8962-audio";
+		ssi-controller = <&ssi2>;
+		audio-codec = <&codec>;
+		audio-routing =
+			"Headphone Jack", "HPOUTL",
+			"Headphone Jack", "HPOUTR",
+			"Ext Spk", "SPKOUTL",
+			"Ext Spk", "SPKOUTR",
+			"AMIC", "MICBIAS",
+			"IN3R", "AMIC";
+		mux-int-port = <2>;
+		mux-ext-port = <6>;
+		hp-det-gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+	};
+
+	panel {
+		compatible = "sii,43wvf1g";
+		backlight = <&backlight_display>;
+		dvdd-supply = <&reg_lcd_3v3>;
+		avdd-supply = <&reg_lcd_5v>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
+	spdif_out: spdif-out {
+		compatible = "linux,spdif-dit";
+		#sound-dai-cells = <0>;
+	};
+
+	sound-spdif {
+		compatible = "fsl,imx6sx-sdb-spdif",
+			     "fsl,imx-audio-spdif";
+		model = "imx-spdif";
+		audio-cpu = <&spdif>;
+		audio-codec = <&spdif_out>;
+	};
+
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	phy-supply = <&reg_enet_3v3>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy1>;
+	phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@1 {
+			reg = <1>;
+		};
+
+		ethphy2: ethernet-phy@2 {
+			reg = <2>;
+		};
+	};
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy2>;
+	fsl,magic-packet;
+	status = "okay";
+};
+
+&flexcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_can_stby>;
+	status = "okay";
+};
+
+&flexcan2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	xceiver-supply = <&reg_can_stby>;
+	status = "okay";
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+};
+
+&i2c4 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	status = "okay";
+
+	codec: wm8962@1a {
+		compatible = "wlf,wm8962";
+		reg = <0x1a>;
+		clocks = <&clks IMX6SX_CLK_AUDIO>;
+		DCVDD-supply = <&vgen4_reg>;
+		DBVDD-supply = <&vgen4_reg>;
+		AVDD-supply = <&vgen4_reg>;
+		CPVDD-supply = <&vgen4_reg>;
+		MICVDD-supply = <&vgen3_reg>;
+		PLLVDD-supply = <&vgen4_reg>;
+		SPKVDD1-supply = <&reg_psu_5v>;
+		SPKVDD2-supply = <&reg_psu_5v>;
+	};
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	reset-gpio = <&gpio2 0 GPIO_ACTIVE_LOW>;
+	vpcie-supply = <&reg_pcie_gpio>;
+	status = "okay";
+};
+
+&lcdif1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lcd>;
+	status = "okay";
+
+	port {
+		display_out: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+};
+
+&snvs_poweroff {
+	status = "okay";
+};
+
+&sai1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai1>;
+	status = "disabled";
+};
+
+&spdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spdif>;
+	assigned-clocks = <&clks IMX6SX_CLK_SPDIF_PODF>;
+	assigned-clock-rates = <24576000>;
+	status = "okay";
+};
+
+&ssi2 {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart5 { /* for bluetooth */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbotg1 {
+	vbus-supply = <&reg_usb_otg1_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_otg1_id>;
+	status = "okay";
+};
+
+&usbotg2 {
+	vbus-supply = <&reg_usb_otg2_vbus>;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbphy1 {
+	fsl,tx-d-cal = <106>;
+};
+
+&usbphy2 {
+	fsl,tx-d-cal = <106>;
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	non-removable;
+	no-1-8-v;
+	keep-power-in-suspend;
+	wakeup-source;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	bus-width = <8>;
+	cd-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio2 15 GPIO_ACTIVE_HIGH>;
+	keep-power-in-suspend;
+	wakeup-source;
+	vmmc-supply = <&vcc_sd3>;
+	status = "okay";
+};
+
+&usdhc4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	cd-gpios = <&gpio6 21 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio6 20 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+};
+
+&iomuxc {
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX6SX_PAD_CSI_DATA00__AUDMUX_AUD6_TXC	0x130b0
+			MX6SX_PAD_CSI_DATA01__AUDMUX_AUD6_TXFS	0x130b0
+			MX6SX_PAD_CSI_HSYNC__AUDMUX_AUD6_TXD	0x120b0
+			MX6SX_PAD_CSI_VSYNC__AUDMUX_AUD6_RXD	0x130b0
+			MX6SX_PAD_CSI_PIXCLK__AUDMUX_MCLK	0x130b0
+		>;
+	};
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6SX_PAD_ENET1_MDIO__ENET1_MDIO	0xa0b1
+			MX6SX_PAD_ENET1_MDC__ENET1_MDC		0xa0b1
+			MX6SX_PAD_RGMII1_TXC__ENET1_RGMII_TXC	0xa0b1
+			MX6SX_PAD_RGMII1_TD0__ENET1_TX_DATA_0	0xa0b1
+			MX6SX_PAD_RGMII1_TD1__ENET1_TX_DATA_1	0xa0b1
+			MX6SX_PAD_RGMII1_TD2__ENET1_TX_DATA_2	0xa0b1
+			MX6SX_PAD_RGMII1_TD3__ENET1_TX_DATA_3	0xa0b1
+			MX6SX_PAD_RGMII1_TX_CTL__ENET1_TX_EN	0xa0b1
+			MX6SX_PAD_RGMII1_RXC__ENET1_RX_CLK	0x3081
+			MX6SX_PAD_RGMII1_RD0__ENET1_RX_DATA_0	0x3081
+			MX6SX_PAD_RGMII1_RD1__ENET1_RX_DATA_1	0x3081
+			MX6SX_PAD_RGMII1_RD2__ENET1_RX_DATA_2	0x3081
+			MX6SX_PAD_RGMII1_RD3__ENET1_RX_DATA_3	0x3081
+			MX6SX_PAD_RGMII1_RX_CTL__ENET1_RX_EN	0x3081
+			MX6SX_PAD_ENET2_RX_CLK__ENET2_REF_CLK_25M	0x91
+			/* phy reset */
+			MX6SX_PAD_ENET2_CRS__GPIO2_IO_7		0x10b0
+		>;
+	};
+
+	pinctrl_enet_3v3: enet3v3grp {
+		fsl,pins = <
+			MX6SX_PAD_ENET2_COL__GPIO2_IO_6		0x80000000
+		>;
+	};
+
+	pinctrl_enet2: enet2grp {
+		fsl,pins = <
+			MX6SX_PAD_RGMII2_TXC__ENET2_RGMII_TXC	0xa0b9
+			MX6SX_PAD_RGMII2_TD0__ENET2_TX_DATA_0	0xa0b1
+			MX6SX_PAD_RGMII2_TD1__ENET2_TX_DATA_1	0xa0b1
+			MX6SX_PAD_RGMII2_TD2__ENET2_TX_DATA_2	0xa0b1
+			MX6SX_PAD_RGMII2_TD3__ENET2_TX_DATA_3	0xa0b1
+			MX6SX_PAD_RGMII2_TX_CTL__ENET2_TX_EN	0xa0b1
+			MX6SX_PAD_RGMII2_RXC__ENET2_RX_CLK	0x3081
+			MX6SX_PAD_RGMII2_RD0__ENET2_RX_DATA_0	0x3081
+			MX6SX_PAD_RGMII2_RD1__ENET2_RX_DATA_1	0x3081
+			MX6SX_PAD_RGMII2_RD2__ENET2_RX_DATA_2	0x3081
+			MX6SX_PAD_RGMII2_RD3__ENET2_RX_DATA_3	0x3081
+			MX6SX_PAD_RGMII2_RX_CTL__ENET2_RX_EN	0x3081
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX6SX_PAD_QSPI1B_DQS__CAN1_TX		0x1b020
+			MX6SX_PAD_QSPI1A_SS1_B__CAN1_RX		0x1b020
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins = <
+			MX6SX_PAD_QSPI1B_SS1_B__CAN2_RX		0x1b020
+			MX6SX_PAD_QSPI1A_DQS__CAN2_TX		0x1b020
+		>;
+	};
+
+	pinctrl_gpio_keys: gpio_keysgrp {
+		fsl,pins = <
+			MX6SX_PAD_CSI_DATA04__GPIO1_IO_18 0x17059
+			MX6SX_PAD_CSI_DATA05__GPIO1_IO_19 0x17059
+		>;
+	};
+
+	pinctrl_hp: hpgrp {
+		fsl,pins = <
+			MX6SX_PAD_CSI_DATA03__GPIO1_IO_17 0x17059
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6SX_PAD_GPIO1_IO01__I2C1_SDA		0x4001b8b1
+			MX6SX_PAD_GPIO1_IO00__I2C1_SCL		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6SX_PAD_KEY_ROW4__I2C3_SDA		0x4001b8b1
+			MX6SX_PAD_KEY_COL4__I2C3_SCL		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX6SX_PAD_CSI_DATA07__I2C4_SDA		0x4001b8b1
+			MX6SX_PAD_CSI_DATA06__I2C4_SCL		0x4001b8b1
+		>;
+	};
+
+	pinctrl_lcd: lcdgrp {
+		fsl,pins = <
+			MX6SX_PAD_LCD1_DATA00__LCDIF1_DATA_0 0x4001b0b0
+			MX6SX_PAD_LCD1_DATA01__LCDIF1_DATA_1 0x4001b0b0
+			MX6SX_PAD_LCD1_DATA02__LCDIF1_DATA_2 0x4001b0b0
+			MX6SX_PAD_LCD1_DATA03__LCDIF1_DATA_3 0x4001b0b0
+			MX6SX_PAD_LCD1_DATA04__LCDIF1_DATA_4 0x4001b0b0
+			MX6SX_PAD_LCD1_DATA05__LCDIF1_DATA_5 0x4001b0b0
+			MX6SX_PAD_LCD1_DATA06__LCDIF1_DATA_6 0x4001b0b0
+			MX6SX_PAD_LCD1_DATA07__LCDIF1_DATA_7 0x4001b0b0
+			MX6SX_PAD_LCD1_DATA08__LCDIF1_DATA_8 0x4001b0b0
+			MX6SX_PAD_LCD1_DATA09__LCDIF1_DATA_9 0x4001b0b0
+			MX6SX_PAD_LCD1_DATA10__LCDIF1_DATA_10 0x4001b0b0
+			MX6SX_PAD_LCD1_DATA11__LCDIF1_DATA_11 0x4001b0b0
+			MX6SX_PAD_LCD1_DATA12__LCDIF1_DATA_12 0x4001b0b0
+			MX6SX_PAD_LCD1_DATA13__LCDIF1_DATA_13 0x4001b0b0
+			MX6SX_PAD_LCD1_DATA14__LCDIF1_DATA_14 0x4001b0b0
+			MX6SX_PAD_LCD1_DATA15__LCDIF1_DATA_15 0x4001b0b0
+			MX6SX_PAD_LCD1_DATA16__LCDIF1_DATA_16 0x4001b0b0
+			MX6SX_PAD_LCD1_DATA17__LCDIF1_DATA_17 0x4001b0b0
+			MX6SX_PAD_LCD1_DATA18__LCDIF1_DATA_18 0x4001b0b0
+			MX6SX_PAD_LCD1_DATA19__LCDIF1_DATA_19 0x4001b0b0
+			MX6SX_PAD_LCD1_DATA20__LCDIF1_DATA_20 0x4001b0b0
+			MX6SX_PAD_LCD1_DATA21__LCDIF1_DATA_21 0x4001b0b0
+			MX6SX_PAD_LCD1_DATA22__LCDIF1_DATA_22 0x4001b0b0
+			MX6SX_PAD_LCD1_DATA23__LCDIF1_DATA_23 0x4001b0b0
+			MX6SX_PAD_LCD1_CLK__LCDIF1_CLK	0x4001b0b0
+			MX6SX_PAD_LCD1_ENABLE__LCDIF1_ENABLE 0x4001b0b0
+			MX6SX_PAD_LCD1_VSYNC__LCDIF1_VSYNC 0x4001b0b0
+			MX6SX_PAD_LCD1_HSYNC__LCDIF1_HSYNC 0x4001b0b0
+			MX6SX_PAD_LCD1_RESET__GPIO3_IO_27 0x4001b0b0
+		>;
+	};
+
+	pinctrl_mqs: mqsgrp {
+		fsl,pins = <
+			MX6SX_PAD_SD2_CLK__MQS_RIGHT 0x120b0
+			MX6SX_PAD_SD2_CMD__MQS_LEFT  0x120b0
+		>;
+	};
+
+	pinctrl_pcie: pciegrp {
+		fsl,pins = <
+			MX6SX_PAD_ENET1_COL__GPIO2_IO_0 0x10b0
+		>;
+	};
+
+	pinctrl_pcie_reg: pciereggrp {
+		fsl,pins = <
+			MX6SX_PAD_ENET1_CRS__GPIO2_IO_1	0x10b0
+		>;
+	};
+
+	pinctrl_peri_3v3: peri3v3grp {
+		fsl,pins = <
+			MX6SX_PAD_QSPI1A_DATA0__GPIO4_IO_16	0x80000000
+		>;
+	};
+
+	pinctrl_pwm3: pwm3-1grp {
+		fsl,pins = <
+			MX6SX_PAD_SD1_DATA2__PWM3_OUT 0x110b0
+		>;
+	};
+
+	pinctrl_qspi2: qspi2grp {
+		fsl,pins = <
+			MX6SX_PAD_NAND_WP_B__QSPI2_A_DATA_0     0x70f1
+			MX6SX_PAD_NAND_READY_B__QSPI2_A_DATA_1  0x70f1
+			MX6SX_PAD_NAND_CE0_B__QSPI2_A_DATA_2    0x70f1
+			MX6SX_PAD_NAND_CE1_B__QSPI2_A_DATA_3    0x70f1
+			MX6SX_PAD_NAND_CLE__QSPI2_A_SCLK        0x70f1
+			MX6SX_PAD_NAND_ALE__QSPI2_A_SS0_B       0x70f1
+			MX6SX_PAD_NAND_DATA01__QSPI2_B_DATA_0   0x70f1
+			MX6SX_PAD_NAND_DATA00__QSPI2_B_DATA_1   0x70f1
+			MX6SX_PAD_NAND_WE_B__QSPI2_B_DATA_2     0x70f1
+			MX6SX_PAD_NAND_RE_B__QSPI2_B_DATA_3     0x70f1
+			MX6SX_PAD_NAND_DATA02__QSPI2_B_SCLK     0x70f1
+			MX6SX_PAD_NAND_DATA03__QSPI2_B_SS0_B    0x70f1
+		>;
+	};
+
+	pinctrl_vcc_sd3: vccsd3grp {
+		fsl,pins = <
+			MX6SX_PAD_KEY_COL1__GPIO2_IO_11		0x17059
+		>;
+	};
+
+	pinctrl_sai1: sai1grp {
+		fsl,pins = <
+			MX6SX_PAD_CSI_DATA00__SAI1_TX_BCLK	0x130b0
+			MX6SX_PAD_CSI_DATA01__SAI1_TX_SYNC	0x130b0
+			MX6SX_PAD_CSI_HSYNC__SAI1_TX_DATA_0	0x120b0
+			MX6SX_PAD_CSI_VSYNC__SAI1_RX_DATA_0	0x130b0
+			MX6SX_PAD_CSI_PIXCLK__AUDMUX_MCLK	0x130b0
+		>;
+	};
+
+	pinctrl_spdif: spdifgrp {
+		fsl,pins = <
+			MX6SX_PAD_SD4_DATA4__SPDIF_OUT          0x1b0b0
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6SX_PAD_GPIO1_IO04__UART1_DCE_TX	0x1b0b1
+			MX6SX_PAD_GPIO1_IO05__UART1_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6SX_PAD_KEY_ROW3__UART5_DCE_RX	0x1b0b1
+			MX6SX_PAD_KEY_COL3__UART5_DCE_TX	0x1b0b1
+			MX6SX_PAD_KEY_ROW2__UART5_DCE_CTS	0x1b0b1
+			MX6SX_PAD_KEY_COL2__UART5_DCE_RTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_usb_otg1: usbotg1grp {
+		fsl,pins = <
+			MX6SX_PAD_GPIO1_IO09__GPIO1_IO_9	0x10b0
+		>;
+	};
+
+	pinctrl_usb_otg1_id: usbotg1idgrp {
+		fsl,pins = <
+			MX6SX_PAD_GPIO1_IO10__ANATOP_OTG1_ID	0x17059
+		>;
+	};
+
+	pinctrl_usb_otg2: usbot2ggrp {
+		fsl,pins = <
+			MX6SX_PAD_GPIO1_IO12__GPIO1_IO_12	0x10b0
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6SX_PAD_SD2_CMD__USDHC2_CMD		0x17059
+			MX6SX_PAD_SD2_CLK__USDHC2_CLK		0x10059
+			MX6SX_PAD_SD2_DATA0__USDHC2_DATA0	0x17059
+			MX6SX_PAD_SD2_DATA1__USDHC2_DATA1	0x17059
+			MX6SX_PAD_SD2_DATA2__USDHC2_DATA2	0x17059
+			MX6SX_PAD_SD2_DATA3__USDHC2_DATA3	0x17059
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6SX_PAD_SD3_CMD__USDHC3_CMD		0x17059
+			MX6SX_PAD_SD3_CLK__USDHC3_CLK		0x10059
+			MX6SX_PAD_SD3_DATA0__USDHC3_DATA0	0x17059
+			MX6SX_PAD_SD3_DATA1__USDHC3_DATA1	0x17059
+			MX6SX_PAD_SD3_DATA2__USDHC3_DATA2	0x17059
+			MX6SX_PAD_SD3_DATA3__USDHC3_DATA3	0x17059
+			MX6SX_PAD_SD3_DATA4__USDHC3_DATA4	0x17059
+			MX6SX_PAD_SD3_DATA5__USDHC3_DATA5	0x17059
+			MX6SX_PAD_SD3_DATA6__USDHC3_DATA6	0x17059
+			MX6SX_PAD_SD3_DATA7__USDHC3_DATA7	0x17059
+			MX6SX_PAD_KEY_COL0__GPIO2_IO_10		0x17059 /* CD */
+			MX6SX_PAD_KEY_ROW0__GPIO2_IO_15		0x17059 /* WP */
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX6SX_PAD_SD3_CMD__USDHC3_CMD		0x170b9
+			MX6SX_PAD_SD3_CLK__USDHC3_CLK		0x100b9
+			MX6SX_PAD_SD3_DATA0__USDHC3_DATA0	0x170b9
+			MX6SX_PAD_SD3_DATA1__USDHC3_DATA1	0x170b9
+			MX6SX_PAD_SD3_DATA2__USDHC3_DATA2	0x170b9
+			MX6SX_PAD_SD3_DATA3__USDHC3_DATA3	0x170b9
+			MX6SX_PAD_SD3_DATA4__USDHC3_DATA4	0x170b9
+			MX6SX_PAD_SD3_DATA5__USDHC3_DATA5	0x170b9
+			MX6SX_PAD_SD3_DATA6__USDHC3_DATA6	0x170b9
+			MX6SX_PAD_SD3_DATA7__USDHC3_DATA7	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX6SX_PAD_SD3_CMD__USDHC3_CMD		0x170f9
+			MX6SX_PAD_SD3_CLK__USDHC3_CLK		0x100f9
+			MX6SX_PAD_SD3_DATA0__USDHC3_DATA0	0x170f9
+			MX6SX_PAD_SD3_DATA1__USDHC3_DATA1	0x170f9
+			MX6SX_PAD_SD3_DATA2__USDHC3_DATA2	0x170f9
+			MX6SX_PAD_SD3_DATA3__USDHC3_DATA3	0x170f9
+			MX6SX_PAD_SD3_DATA4__USDHC3_DATA4	0x170f9
+			MX6SX_PAD_SD3_DATA5__USDHC3_DATA5	0x170f9
+			MX6SX_PAD_SD3_DATA6__USDHC3_DATA6	0x170f9
+			MX6SX_PAD_SD3_DATA7__USDHC3_DATA7	0x170f9
+		>;
+	};
+
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6SX_PAD_SD4_CMD__USDHC4_CMD		0x17059
+			MX6SX_PAD_SD4_CLK__USDHC4_CLK		0x10059
+			MX6SX_PAD_SD4_DATA0__USDHC4_DATA0	0x17059
+			MX6SX_PAD_SD4_DATA1__USDHC4_DATA1	0x17059
+			MX6SX_PAD_SD4_DATA2__USDHC4_DATA2	0x17059
+			MX6SX_PAD_SD4_DATA3__USDHC4_DATA3	0x17059
+			MX6SX_PAD_SD4_DATA7__GPIO6_IO_21	0x17059 /* CD */
+			MX6SX_PAD_SD4_DATA6__GPIO6_IO_20	0x17059 /* WP */
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX6SX_PAD_GPIO1_IO13__WDOG1_WDOG_ANY 0x30b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6sx-softing-vining-2000.dts b/arch/arm/boot/dts/nxp/imx/imx6sx-softing-vining-2000.dts
index b9a1401e6c6d..2ffbe2df4776 100644
--- a/arch/arm/boot/dts/imx6sx-softing-vining-2000.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-softing-vining-2000.dts
@@ -46,19 +46,19 @@
 		led-1 {
 			label = "red";
 			max-brightness = <255>;
-			pwms = <&pwm6 0 50000>;
+			pwms = <&pwm6 0 50000 0>;
 		};
 
 		led-2 {
 			label = "green";
 			max-brightness = <255>;
-			pwms = <&pwm2 0 50000>;
+			pwms = <&pwm2 0 50000 0>;
 		};
 
 		led-3 {
 			label = "blue";
 			max-brightness = <255>;
-			pwms = <&pwm1 0 50000>;
+			pwms = <&pwm1 0 50000 0>;
 		};
 	};
 };
@@ -171,7 +171,7 @@
 		reset-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;
 	};
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze200";
 		reg = <0x08>;
 
@@ -358,21 +358,21 @@
 		>;
 	};
 
-	pinctrl_pwm1: pwm1grp-1 {
+	pinctrl_pwm1: pwm1-1grp {
 		fsl,pins = <
 			/* blue LED */
 			MX6SX_PAD_RGMII2_RD3__PWM1_OUT		0x1b0b1
 		>;
 	};
 
-	pinctrl_pwm2: pwm2grp-1 {
+	pinctrl_pwm2: pwm2-1grp {
 		fsl,pins = <
 			/* green LED */
 			MX6SX_PAD_RGMII2_RD2__PWM2_OUT		0x1b0b1
 		>;
 	};
 
-	pinctrl_pwm6: pwm6grp-1 {
+	pinctrl_pwm6: pwm6-1grp {
 		fsl,pins = <
 			/* red LED */
 			MX6SX_PAD_RGMII2_TD2__PWM6_OUT		0x1b0b1
@@ -414,7 +414,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_50mhz: usdhc2grp-50mhz {
+	pinctrl_usdhc2_50mhz: usdhc2-50mhzgrp {
 		fsl,pins = <
 			MX6SX_PAD_SD2_CLK__USDHC2_CLK		0x10059
 			MX6SX_PAD_SD2_CMD__USDHC2_CMD		0x17059
@@ -427,7 +427,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_100mhz: usdhc2grp-100mhz {
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
 		fsl,pins = <
 			MX6SX_PAD_SD2_CLK__USDHC2_CLK		0x100b9
 			MX6SX_PAD_SD2_CMD__USDHC2_CMD		0x170b9
@@ -438,7 +438,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_200mhz: usdhc2grp-200mhz {
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
 		fsl,pins = <
 			MX6SX_PAD_SD2_CLK__USDHC2_CLK		0x100f9
 			MX6SX_PAD_SD2_CMD__USDHC2_CMD		0x170f9
@@ -449,7 +449,7 @@
 		>;
 	};
 
-	pinctrl_usdhc4_50mhz: usdhc4grp-50mhz {
+	pinctrl_usdhc4_50mhz: usdhc4-50mhzgrp {
 		fsl,pins = <
 			MX6SX_PAD_SD4_CLK__USDHC4_CLK		0x10059
 			MX6SX_PAD_SD4_CMD__USDHC4_CMD		0x17059
@@ -465,7 +465,7 @@
 		>;
 	};
 
-	pinctrl_usdhc4_100mhz: usdhc4-100mhz {
+	pinctrl_usdhc4_100mhz: usdhc4-100mhzgrp {
 		fsl,pins = <
 			MX6SX_PAD_SD4_CLK__USDHC4_CLK		0x100b9
 			MX6SX_PAD_SD4_CMD__USDHC4_CMD		0x170b9
@@ -480,7 +480,7 @@
 		>;
 	};
 
-	pinctrl_usdhc4_200mhz: usdhc4-200mhz {
+	pinctrl_usdhc4_200mhz: usdhc4-200mhzgrp {
 		fsl,pins = <
 			MX6SX_PAD_SD4_CLK__USDHC4_CLK		0x100f9
 			MX6SX_PAD_SD4_CMD__USDHC4_CMD		0x170f9
@@ -505,24 +505,18 @@
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
-	status = "okay";
 };
 
 &pwm2 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm2>;
-	status = "okay";
 };
 
 &pwm6 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm6>;
-	status = "okay";
 };
 
 &reg_arm {
diff --git a/arch/arm/boot/dts/imx6sx-udoo-neo-basic.dts b/arch/arm/boot/dts/nxp/imx/imx6sx-udoo-neo-basic.dts
index 205ea26484e3..205ea26484e3 100644
--- a/arch/arm/boot/dts/imx6sx-udoo-neo-basic.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-udoo-neo-basic.dts
diff --git a/arch/arm/boot/dts/imx6sx-udoo-neo-extended.dts b/arch/arm/boot/dts/nxp/imx/imx6sx-udoo-neo-extended.dts
index 5817b4985391..5817b4985391 100644
--- a/arch/arm/boot/dts/imx6sx-udoo-neo-extended.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-udoo-neo-extended.dts
diff --git a/arch/arm/boot/dts/imx6sx-udoo-neo-full.dts b/arch/arm/boot/dts/nxp/imx/imx6sx-udoo-neo-full.dts
index 96f4d89848a3..96f4d89848a3 100644
--- a/arch/arm/boot/dts/imx6sx-udoo-neo-full.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-udoo-neo-full.dts
diff --git a/arch/arm/boot/dts/imx6sx-udoo-neo.dtsi b/arch/arm/boot/dts/nxp/imx/imx6sx-udoo-neo.dtsi
index 35861bbea94e..bbf792ac4896 100644
--- a/arch/arm/boot/dts/imx6sx-udoo-neo.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-udoo-neo.dtsi
@@ -15,14 +15,14 @@
 	leds {
 		compatible = "gpio-leds";
 
-		red {
+		led-red {
 			label = "udoo-neo:red:mmc";
 			gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 			linux,default-trigger = "mmc0";
 		};
 
-		orange {
+		led-orange {
 			label = "udoo-neo:orange:user";
 			gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
@@ -72,6 +72,11 @@
 	};
 };
 
+&clks {
+	assigned-clocks = <&clks IMX6SX_CLK_ENET_REF>;
+	assigned-clock-rates = <50000000>;
+};
+
 &fec1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet1>;
@@ -226,7 +231,7 @@
 &iomuxc {
 	pinctrl_bt_reg: btreggrp {
 		fsl,pins =
-			<MX6SX_PAD_KEY_ROW2__GPIO2_IO_17        0x15059>;
+			<MX6SX_PAD_KEY_ROW2__GPIO2_IO_17	0x15059>;
 	};
 
 	pinctrl_enet1: enet1grp {
@@ -306,7 +311,6 @@
 		>;
 	};
 
-
 	pinctrl_uart1: uart1grp {
 		fsl,pins =
 			<MX6SX_PAD_GPIO1_IO04__UART1_DCE_TX	0x1b0b1>,
@@ -347,24 +351,23 @@
 
 	pinctrl_otg1_reg: otg1grp {
 		fsl,pins =
-			<MX6SX_PAD_GPIO1_IO09__GPIO1_IO_9        0x10b0>;
+			<MX6SX_PAD_GPIO1_IO09__GPIO1_IO_9	0x10b0>;
 	};
 
-
 	pinctrl_otg2_reg: otg2grp {
 		fsl,pins =
-			<MX6SX_PAD_NAND_RE_B__GPIO4_IO_12        0x10b0>;
+			<MX6SX_PAD_NAND_RE_B__GPIO4_IO_12	0x10b0>;
 	};
 
 	pinctrl_usb_otg1: usbotg1grp {
 		fsl,pins =
-			<MX6SX_PAD_GPIO1_IO10__ANATOP_OTG1_ID    0x17059>,
-			<MX6SX_PAD_GPIO1_IO08__USB_OTG1_OC       0x10b0>;
+			<MX6SX_PAD_GPIO1_IO10__ANATOP_OTG1_ID	0x17059>,
+			<MX6SX_PAD_GPIO1_IO08__USB_OTG1_OC	0x10b0>;
 	};
 
 	pinctrl_usb_otg2: usbot2ggrp {
 		fsl,pins =
-			<MX6SX_PAD_QSPI1A_DATA0__USB_OTG2_OC     0x10b0>;
+			<MX6SX_PAD_QSPI1A_DATA0__USB_OTG2_OC	0x10b0>;
 	};
 
 	pinctrl_usdhc2: usdhc2grp {
diff --git a/arch/arm/boot/dts/imx6sx.dtsi b/arch/arm/boot/dts/nxp/imx/imx6sx.dtsi
index fc6334336b3d..5132b575b001 100644
--- a/arch/arm/boot/dts/imx6sx.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx.dtsi
@@ -154,7 +154,7 @@
 		#phy-cells = <0>;
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
@@ -164,12 +164,18 @@
 		ocram_s: sram@8f8000 {
 			compatible = "mmio-sram";
 			reg = <0x008f8000 0x4000>;
+			ranges = <0 0x008f8000 0x4000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6SX_CLK_OCRAM_S>;
 		};
 
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6SX_CLK_OCRAM>;
 		};
 
@@ -203,20 +209,19 @@
 			power-domains = <&pd_pu>;
 		};
 
-		dma_apbh: dma-apbh@1804000 {
+		dma_apbh: dma-controller@1804000 {
 			compatible = "fsl,imx6sx-dma-apbh", "fsl,imx28-dma-apbh";
 			reg = <0x01804000 0x2000>;
 			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3";
 			#dma-cells = <1>;
 			dma-channels = <4>;
 			clocks = <&clks IMX6SX_CLK_APBH_DMA>;
 		};
 
-		gpmi: nand-controller@1806000{
+		gpmi: nand-controller@1806000 {
 			compatible = "fsl,imx6sx-gpmi-nand";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -334,15 +339,14 @@
 				};
 
 				esai: esai@2024000 {
-					compatible = "fsl,imx6sx-esai", "fsl,imx35-esai";
+					compatible = "fsl,imx35-esai";
 					reg = <0x02024000 0x4000>;
 					interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6SX_CLK_ESAI_IPG>,
-						 <&clks IMX6SX_CLK_ESAI_MEM>,
 						 <&clks IMX6SX_CLK_ESAI_EXTAL>,
 						 <&clks IMX6SX_CLK_ESAI_IPG>,
 						 <&clks IMX6SX_CLK_SPBA>;
-					clock-names = "core", "mem", "extal",
+					clock-names = "core", "extal",
 						      "fsys", "spba";
 					dmas = <&sdma 23 21 0>,
 					       <&sdma 24 21 0>;
@@ -413,7 +417,7 @@
 					       <&sdma 21 23 1>, <&sdma 22 23 1>;
 					dma-names = "rxa", "rxb", "rxc",
 						    "txa", "txb", "txc";
-					fsl,asrc-rate  = <48000>;
+					fsl,asrc-rate = <48000>;
 					fsl,asrc-width = <16>;
 					status = "okay";
 				};
@@ -633,8 +637,8 @@
 				reg_vdd3p0: regulator-3p0 {
 					compatible = "fsl,anatop-regulator";
 					regulator-name = "vdd3p0";
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <3150000>;
+					regulator-min-microvolt = <2625000>;
+					regulator-max-microvolt = <3400000>;
 					regulator-always-on;
 					anatop-reg-offset = <0x120>;
 					anatop-vol-bit-shift = <8>;
@@ -711,13 +715,14 @@
 				};
 
 				tempmon: tempmon {
-					compatible = "fsl,imx6sx-tempmon", "fsl,imx6q-tempmon";
+					compatible = "fsl,imx6sx-tempmon";
 					interrupt-parent = <&gpc>;
 					interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
 					fsl,tempmon = <&anatop>;
 					nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
 					nvmem-cell-names = "calib", "temp_grade";
 					clocks = <&clks IMX6SX_CLK_PLL3_USB_OTG>;
+					#thermal-sensor-cells = <0>;
 				};
 			};
 
@@ -726,6 +731,7 @@
 				reg = <0x020c9000 0x1000>;
 				interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6SX_CLK_USBPHY1>;
+				phy-3p0-supply = <&reg_vdd3p0>;
 				fsl,anatop = <&anatop>;
 			};
 
@@ -734,6 +740,7 @@
 				reg = <0x020ca000 0x1000>;
 				interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6SX_CLK_USBPHY2>;
+				phy-3p0-supply = <&reg_vdd3p0>;
 				fsl,anatop = <&anatop>;
 			};
 
@@ -836,13 +843,42 @@
 				reg = <0x020e0000 0x4000>;
 			};
 
-			gpr: iomuxc-gpr@20e4000 {
+			gpr: syscon@20e4000 {
 				compatible = "fsl,imx6sx-iomuxc-gpr",
-					     "fsl,imx6q-iomuxc-gpr", "syscon";
+					     "fsl,imx6q-iomuxc-gpr", "syscon", "simple-mfd";
+				#address-cells = <1>;
+				#size-cells = <1>;
 				reg = <0x020e4000 0x4000>;
+
+				lvds_bridge: bridge@18 {
+					compatible = "fsl,imx6sx-ldb";
+					reg = <0x18 0x4>;
+					clocks = <&clks IMX6SX_CLK_LDB_DI0>;
+					clock-names = "ldb";
+					status = "disabled";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							ldb_from_lcdif1: endpoint {
+							};
+						};
+
+						port@1 {
+							reg = <1>;
+
+							ldb_lvds_ch0: endpoint {
+							};
+						};
+					};
+				};
 			};
 
-			sdma: sdma@20ec000 {
+			sdma: dma-controller@20ec000 {
 				compatible = "fsl,imx6sx-sdma", "fsl,imx6q-sdma";
 				reg = <0x020ec000 0x4000>;
 				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
@@ -895,7 +931,6 @@
 				clocks = <&clks IMX6SX_CLK_USBOH3>;
 				fsl,usbphy = <&usbphy1>;
 				fsl,usbmisc = <&usbmisc 0>;
-				fsl,anatop = <&anatop>;
 				ahb-burst-config = <0x0>;
 				tx-burst-size-dword = <0x10>;
 				rx-burst-size-dword = <0x10>;
@@ -923,7 +958,6 @@
 				fsl,usbphy = <&usbphynop1>;
 				fsl,usbmisc = <&usbmisc 2>;
 				phy_type = "hsic";
-				fsl,anatop = <&anatop>;
 				dr_mode = "host";
 				ahb-burst-config = <0x0>;
 				tx-burst-size-dword = <0x10>;
@@ -967,7 +1001,7 @@
 			};
 
 			usdhc1: mmc@2190000 {
-				compatible = "fsl,imx6sx-usdhc", "fsl,imx6sl-usdhc";
+				compatible = "fsl,imx6sx-usdhc";
 				reg = <0x02190000 0x4000>;
 				interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6SX_CLK_USDHC1>,
@@ -975,11 +1009,13 @@
 					 <&clks IMX6SX_CLK_USDHC1>;
 				clock-names = "ipg", "ahb", "per";
 				bus-width = <4>;
+				fsl,tuning-start-tap = <20>;
+				fsl,tuning-step = <2>;
 				status = "disabled";
 			};
 
 			usdhc2: mmc@2194000 {
-				compatible = "fsl,imx6sx-usdhc", "fsl,imx6sl-usdhc";
+				compatible = "fsl,imx6sx-usdhc";
 				reg = <0x02194000 0x4000>;
 				interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6SX_CLK_USDHC2>,
@@ -987,11 +1023,13 @@
 					 <&clks IMX6SX_CLK_USDHC2>;
 				clock-names = "ipg", "ahb", "per";
 				bus-width = <4>;
+				fsl,tuning-start-tap = <20>;
+				fsl,tuning-step = <2>;
 				status = "disabled";
 			};
 
 			usdhc3: mmc@2198000 {
-				compatible = "fsl,imx6sx-usdhc", "fsl,imx6sl-usdhc";
+				compatible = "fsl,imx6sx-usdhc";
 				reg = <0x02198000 0x4000>;
 				interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6SX_CLK_USDHC3>,
@@ -999,11 +1037,13 @@
 					 <&clks IMX6SX_CLK_USDHC3>;
 				clock-names = "ipg", "ahb", "per";
 				bus-width = <4>;
+				fsl,tuning-start-tap = <20>;
+				fsl,tuning-step = <2>;
 				status = "disabled";
 			};
 
 			usdhc4: mmc@219c000 {
-				compatible = "fsl,imx6sx-usdhc", "fsl,imx6sl-usdhc";
+				compatible = "fsl,imx6sx-usdhc";
 				reg = <0x0219c000 0x4000>;
 				interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6SX_CLK_USDHC4>,
@@ -1067,7 +1107,7 @@
 				status = "disabled";
 			};
 
-			weim: weim@21b8000 {
+			weim: memory-controller@21b8000 {
 				#address-cells = <2>;
 				#size-cells = <1>;
 				compatible = "fsl,imx6sx-weim", "fsl,imx6q-weim";
@@ -1271,8 +1311,17 @@
 						 <&clks IMX6SX_CLK_LCDIF_APB>,
 						 <&clks IMX6SX_CLK_DISPLAY_AXI>;
 					clock-names = "pix", "axi", "disp_axi";
+					assigned-clocks = <&clks IMX6SX_CLK_LCDIF1_PRE_SEL>,
+							  <&clks IMX6SX_CLK_LCDIF1_SEL>;
+					assigned-clock-parents = <&clks IMX6SX_CLK_PLL5_VIDEO_DIV>,
+								 <&clks IMX6SX_CLK_LCDIF1_PODF>;
 					power-domains = <&pd_disp>;
 					status = "disabled";
+
+					port {
+						lcdif1_to_ldb: endpoint {
+						};
+					};
 				};
 
 				lcdif2: lcdif@2224000 {
@@ -1385,7 +1434,7 @@
 
 			pwm8: pwm@22b0000 {
 				compatible = "fsl,imx6sx-pwm", "fsl,imx27-pwm";
-				reg = <0x0022b0000 0x4000>;
+				reg = <0x022b0000 0x4000>;
 				interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6SX_CLK_PWM8>,
 					 <&clks IMX6SX_CLK_PWM8>;
diff --git a/arch/arm/boot/dts/imx6ul-14x14-evk.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dts
index 2438669f149a..2438669f149a 100644
--- a/arch/arm/boot/dts/imx6ul-14x14-evk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dts
diff --git a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi
index a3fde3316c73..73c9cfbdba62 100644
--- a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi
@@ -2,6 +2,8 @@
 //
 // Copyright (C) 2015 Freescale Semiconductor, Inc.
 
+#include <dt-bindings/media/video-interfaces.h>
+
 / {
 	chosen {
 		stdout-path = &uart1;
@@ -14,12 +16,32 @@
 
 	backlight_display: backlight-display {
 		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
 		status = "okay";
 	};
 
+	reg_1v5: regulator-1v5 {
+		compatible = "regulator-fixed";
+		regulator-name = "1v5";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+	};
+
+	reg_1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	reg_2v8: regulator-2v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "2v8";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+	};
 
 	reg_sd1_vmmc: regulator-sd1-vmmc {
 		compatible = "regulator-fixed";
@@ -60,13 +82,40 @@
 		gpios = <&gpio_spi 3 GPIO_ACTIVE_LOW>;
 	};
 
+	reg_audio_5v: regulator-audio-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "audio-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	reg_audio_3v3: regulator-audio-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "audio-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	reg_audio_1v8: regulator-audio-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "audio-1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
 	sound-wm8960 {
 		compatible = "fsl,imx-audio-wm8960";
 		model = "wm8960-audio";
 		audio-cpu = <&sai2>;
 		audio-codec = <&codec>;
 		audio-asrc = <&asrc>;
-		hp-det-gpio = <&gpio5 4 0>;
+		hp-det-gpios = <&gpio5 4 0>;
 		audio-routing =
 			"Headphone Jack", "HP_L",
 			"Headphone Jack", "HP_R",
@@ -82,13 +131,13 @@
 			"AMIC", "MICB";
 	};
 
-	spi4 {
+	spi-4 {
 		compatible = "spi-gpio";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_spi4>;
 		status = "okay";
-		gpio-sck = <&gpio5 11 0>;
-		gpio-mosi = <&gpio5 10 0>;
+		sck-gpios = <&gpio5 11 0>;
+		mosi-gpios = <&gpio5 10 0>;
 		cs-gpios = <&gpio5 7 GPIO_ACTIVE_LOW>;
 		num-chipselects = <1>;
 		#address-cells = <1>;
@@ -137,6 +186,11 @@
 		wlf,gpio-cfg = <1 3>;
 		clocks = <&clks IMX6UL_CLK_SAI2>;
 		clock-names = "mclk";
+		AVDD-supply = <&reg_audio_3v3>;
+		DBVDD-supply = <&reg_audio_1v8>;
+		DCVDD-supply = <&reg_audio_1v8>;
+		SPKVDD1-supply = <&reg_audio_5v>;
+		SPKVDD2-supply = <&reg_audio_5v>;
 	};
 
 	camera@3c {
@@ -148,6 +202,9 @@
 		clock-names = "xclk";
 		powerdown-gpios = <&gpio_spi 6 GPIO_ACTIVE_HIGH>;
 		reset-gpios = <&gpio_spi 5 GPIO_ACTIVE_LOW>;
+		AVDD-supply = <&reg_2v8>;
+		DVDD-supply = <&reg_1v5>;
+		DOVDD-supply = <&reg_1v8>;
 
 		port {
 			ov5640_to_parallel: endpoint {
@@ -170,7 +227,7 @@
 	port {
 		parallel_from_ov5640: endpoint {
 			remote-endpoint = <&ov5640_to_parallel>;
-			bus-type = <5>; /* Parallel bus */
+			bus-type = <MEDIA_BUS_TYPE_PARALLEL>;
 		};
 	};
 };
@@ -275,7 +332,6 @@
 };
 
 &pwm1 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
@@ -286,7 +342,7 @@
 	pinctrl-0 = <&pinctrl_qspi>;
 	status = "okay";
 
-	flash0: n25q256a@0 {
+	flash0: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q256a", "jedec,spi-nor";
@@ -319,7 +375,7 @@
 &tsc {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_tsc>;
-	xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+	xnur-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
 	measure-delay-time = <0xffff>;
 	pre-charge-time = <0xfff>;
 	status = "okay";
@@ -388,8 +444,6 @@
 };
 
 &iomuxc {
-	pinctrl-names = "default";
-
 	pinctrl_camera_clock: cameraclockgrp {
 		fsl,pins = <
 			MX6UL_PAD_CSI_MCLK__CSI_MCLK		0x1b088
@@ -440,14 +494,14 @@
 		>;
 	};
 
-	pinctrl_flexcan1: flexcan1grp{
+	pinctrl_flexcan1: flexcan1grp {
 		fsl,pins = <
 			MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX	0x1b020
 			MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX	0x1b020
 		>;
 	};
 
-	pinctrl_flexcan2: flexcan2grp{
+	pinctrl_flexcan2: flexcan2grp {
 		fsl,pins = <
 			MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX	0x1b020
 			MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX	0x1b020
@@ -607,7 +661,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+	pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp {
 		fsl,pins = <
 			MX6UL_PAD_SD1_CMD__USDHC1_CMD     0x170b9
 			MX6UL_PAD_SD1_CLK__USDHC1_CLK     0x100b9
@@ -619,7 +673,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+	pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
 		fsl,pins = <
 			MX6UL_PAD_SD1_CMD__USDHC1_CMD     0x170f9
 			MX6UL_PAD_SD1_CLK__USDHC1_CLK     0x100f9
diff --git a/arch/arm/boot/dts/imx6ul-ccimx6ulsbcexpress.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-ccimx6ulsbcexpress.dts
index 3792679c0c90..0d3b1ab82eab 100644
--- a/arch/arm/boot/dts/imx6ul-ccimx6ulsbcexpress.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-ccimx6ulsbcexpress.dts
@@ -112,7 +112,7 @@
 		>;
 	};
 
-	pinctrl_ecspi3_master: ecspi3grp1 {
+	pinctrl_ecspi3_master: ecspi3-1-grp {
 		fsl,pins = <
 			MX6UL_PAD_UART2_RX_DATA__ECSPI3_SCLK	0x10b0
 			MX6UL_PAD_UART2_CTS_B__ECSPI3_MOSI	0x10b0
@@ -121,7 +121,7 @@
 		>;
 	};
 
-	pinctrl_ecspi3_slave: ecspi3grp2 {
+	pinctrl_ecspi3_slave: ecspi3-2-grp {
 		fsl,pins = <
 			MX6UL_PAD_UART2_RX_DATA__ECSPI3_SCLK	0x10b0
 			MX6UL_PAD_UART2_CTS_B__ECSPI3_MOSI	0x10b0
@@ -145,7 +145,7 @@
 		>;
 	};
 
-	pinctrl_flexcan1: flexcan1grp{
+	pinctrl_flexcan1: flexcan1grp {
 		fsl,pins = <
 			MX6UL_PAD_LCD_DATA08__FLEXCAN1_TX	0x1b020
 			MX6UL_PAD_LCD_DATA09__FLEXCAN1_RX	0x1b020
diff --git a/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-ccimx6ulsbcpro.dts
index 3ec042bfccba..8aea8c99e2af 100644
--- a/arch/arm/boot/dts/imx6ul-ccimx6ulsbcpro.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-ccimx6ulsbcpro.dts
@@ -18,7 +18,7 @@
 
 	lcd_backlight: backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm5 0 50000>;
+		pwms = <&pwm5 0 50000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
 		status = "okay";
@@ -168,7 +168,6 @@
 };
 
 &pwm5 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm5>;
 	status = "okay";
@@ -249,7 +248,7 @@
 		>;
 	};
 
-	pinctrl_ecspi1_master: ecspi1grp1 {
+	pinctrl_ecspi1_master: ecspi1-1-grp {
 		fsl,pins = <
 			MX6UL_PAD_LCD_DATA20__ECSPI1_SCLK	0x10b0
 			MX6UL_PAD_LCD_DATA22__ECSPI1_MOSI	0x10b0
@@ -291,26 +290,26 @@
 		>;
 	};
 
-	pinctrl_flexcan1: flexcan1grp{
+	pinctrl_flexcan1: flexcan1grp {
 		fsl,pins = <
 			MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX	0x1b020
 			MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX	0x1b020
 		>;
 	};
-	pinctrl_flexcan2: flexcan2grp{
+	pinctrl_flexcan2: flexcan2grp {
 		fsl,pins = <
 			MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX	0x1b020
 			MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX	0x1b020
 		>;
 	};
 
-	pinctrl_goodix_touch: goodixgrp{
+	pinctrl_goodix_touch: goodixgrp {
 		fsl,pins = <
 			MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x1020
 		>;
 	};
 
-	pinctrl_lcdif_dat0_17: lcdifdatgrp0-17 {
+	pinctrl_lcdif_dat0_17: lcdifdat0-17-grp {
 		fsl,pins = <
 			MX6UL_PAD_LCD_DATA00__LCDIF_DATA00	0x79
 			MX6UL_PAD_LCD_DATA01__LCDIF_DATA01	0x79
@@ -333,14 +332,14 @@
 		>;
 	};
 
-	pinctrl_lcdif_clken: lcdifctrlgrp1 {
+	pinctrl_lcdif_clken: lcdifctrl-1-grp {
 		fsl,pins = <
 			MX6UL_PAD_LCD_CLK__LCDIF_CLK		0x17050
 			MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE	0x79
 		>;
 	};
 
-	pinctrl_lcdif_hvsync: lcdifctrlgrp2 {
+	pinctrl_lcdif_hvsync: lcdifctrl-2-grp {
 		fsl,pins = <
 			MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC	0x79
 			MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC	0x79
@@ -371,7 +370,7 @@
 		>;
 	};
 
-	pinctrl_sai2_sleep: sai2grp-sleep {
+	pinctrl_sai2_sleep: sai2-sleep-grp {
 		fsl,pins = <
 			MX6UL_PAD_JTAG_TRST_B__GPIO1_IO15	0x3000
 			MX6UL_PAD_JTAG_TCK__GPIO1_IO14		0x3000
@@ -382,7 +381,7 @@
 		>;
 	};
 
-	pinctrl_uart2_4wires: uart2grp-4wires {
+	pinctrl_uart2_4wires: uart2-4wires-grp {
 		fsl,pins = <
 			MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX	0x1b0b1
 			MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX	0x1b0b1
@@ -391,7 +390,7 @@
 		>;
 	};
 
-	pinctrl_uart3_2wires: uart3grp-2wires {
+	pinctrl_uart3_2wires: uart3-2wires-grp {
 		fsl,pins = <
 			MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX	0x1b0b1
 			MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX	0x1b0b1
diff --git a/arch/arm/boot/dts/imx6ul-ccimx6ulsom.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-ccimx6ulsom.dtsi
index b5781c3656d1..9cc3eebb6b05 100644
--- a/arch/arm/boot/dts/imx6ul-ccimx6ulsom.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-ccimx6ulsom.dtsi
@@ -114,7 +114,6 @@
 			};
 
 			vdda_adc_3v3: vldo1 {
-				compatible = "regulator-fixed";
 				regulator-name = "vref-adc-3v3";
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
@@ -158,7 +157,7 @@
 				regulator-max-microvolt = <3300000>;
 			};
 
-			vcoin_chg: vcoin {
+			vcoin_chg: coin {
 				regulator-min-microvolt = <2500000>;
 				regulator-max-microvolt = <3300000>;
 			};
@@ -233,7 +232,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_sleep: usdhc1grp-sleep {
+	pinctrl_usdhc1_sleep: usdhc1-sleep-grp {
 		fsl,pins = <
 			MX6UL_PAD_SD1_CMD__GPIO2_IO16           0x3000
 			MX6UL_PAD_SD1_CLK__GPIO2_IO17           0x3000
@@ -251,7 +250,7 @@
 		>;
 	};
 
-	pinctrl_wifibt_ctrl_sleep: wifibt-ctrl-grp-sleep {
+	pinctrl_wifibt_ctrl_sleep: wifibt-ctrl-sleep-grp {
 		fsl,pins = <
 			MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00      0x3000
 			MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09      0x3000
diff --git a/arch/arm/boot/dts/imx6ul-geam.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts
index a0097da03f38..2a6bb5ff808a 100644
--- a/arch/arm/boot/dts/imx6ul-geam.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts
@@ -21,7 +21,7 @@
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm8 0 100000>;
+		pwms = <&pwm8 0 100000 0>;
 		brightness-levels = < 0  1  2  3  4  5  6  7  8  9
 				     10 11 12 13 14 15 16 17 18 19
 				     20 21 22 23 24 25 26 27 28 29
@@ -148,7 +148,6 @@
 		reg = <0x0a>;
 		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6UL_CLK_OSC>;
-		clock-names = "mclk";
 		VDDA-supply = <&reg_3p3v>;
 		VDDIO-supply = <&reg_3p3v>;
 		VDDD-supply = <&reg_1p8v>;
@@ -195,7 +194,6 @@
 };
 
 &pwm8 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm8>;
 	status = "okay";
@@ -204,7 +202,7 @@
 &tsc {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_tsc>;
-	xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+	xnur-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
 };
 
 &sai2 {
@@ -367,7 +365,7 @@
 	};
 
 	pinctrl_tsc: tscgrp {
-		fsl,pin = <
+		fsl,pins = <
 			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01	0xb0
 			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0xb0
 			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0xb0
@@ -412,7 +410,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+	pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp {
 		fsl,pins = <
 			MX6UL_PAD_SD1_CMD__USDHC1_CMD     0x170b9
 			MX6UL_PAD_SD1_CLK__USDHC1_CLK     0x100b9
@@ -423,7 +421,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+	pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
 		fsl,pins = <
 			MX6UL_PAD_SD1_CMD__USDHC1_CMD     0x170f9
 			MX6UL_PAD_SD1_CLK__USDHC1_CLK     0x100f9
diff --git a/arch/arm/boot/dts/imx6ul-imx6ull-opos6ul.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6ul.dtsi
index f2386dcb9ff2..dda4fa91b2f2 100644
--- a/arch/arm/boot/dts/imx6ul-imx6ull-opos6ul.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6ul.dtsi
@@ -40,6 +40,9 @@
 			reg = <1>;
 			interrupt-parent = <&gpio4>;
 			interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
+			micrel,led-mode = <1>;
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			clock-names = "rmii-ref";
 			status = "okay";
 		};
 	};
diff --git a/arch/arm/boot/dts/imx6ul-imx6ull-opos6uldev.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi
index 18cac19aa9b0..be3cacb4fa7a 100644
--- a/arch/arm/boot/dts/imx6ul-imx6ull-opos6uldev.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi
@@ -9,7 +9,7 @@
 
 	backlight: backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm3 0 191000>;
+		pwms = <&pwm3 0 191000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <7>;
 		power-supply = <&reg_5v>;
@@ -143,7 +143,6 @@
 };
 
 &pwm3 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "okay";
@@ -156,7 +155,7 @@
 &tsc {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_tsc>;
-	xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+	xnur-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
 	measure-delay-time = <0xffff>;
 	pre-charge-time = <0xffff>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6ul-isiot-emmc.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-isiot-emmc.dts
index 1df3e376ae2c..1df3e376ae2c 100644
--- a/arch/arm/boot/dts/imx6ul-isiot-emmc.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-isiot-emmc.dts
diff --git a/arch/arm/boot/dts/imx6ul-isiot-nand.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-isiot-nand.dts
index 8c26d4d1a7bf..8c26d4d1a7bf 100644
--- a/arch/arm/boot/dts/imx6ul-isiot-nand.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-isiot-nand.dts
diff --git a/arch/arm/boot/dts/imx6ul-isiot.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-isiot.dtsi
index 14fc4828ba4e..4c09bb312696 100644
--- a/arch/arm/boot/dts/imx6ul-isiot.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-isiot.dtsi
@@ -20,7 +20,7 @@
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm8 0 100000>;
+		pwms = <&pwm8 0 100000 0>;
 		brightness-levels = < 0  1  2  3  4  5  6  7  8  9
 				     10 11 12 13 14 15 16 17 18 19
 				     20 21 22 23 24 25 26 27 28 29
@@ -187,7 +187,6 @@
 };
 
 &pwm8 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm8>;
 	status = "okay";
@@ -323,7 +322,7 @@
 		>;
 	};
 
-	pinctrl_stmpe: stmpegrp  {
+	pinctrl_stmpe: stmpegrp {
 		fsl,pins = <
 			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18 0x1b0b0
 		>;
@@ -347,7 +346,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+	pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp {
 		fsl,pins = <
 			MX6UL_PAD_SD1_CMD__USDHC1_CMD     0x170b9
 			MX6UL_PAD_SD1_CLK__USDHC1_CLK     0x100b9
@@ -358,7 +357,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+	pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
 		fsl,pins = <
 			MX6UL_PAD_SD1_CMD__USDHC1_CMD     0x170f9
 			MX6UL_PAD_SD1_CLK__USDHC1_CLK     0x100f9
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6310-s-43.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl-43.dts
index 5bfad4655b22..4e8191a65211 100644
--- a/arch/arm/boot/dts/imx6ul-kontron-n6310-s-43.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl-43.dts
@@ -5,16 +5,16 @@
  * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
  */
 
-#include "imx6ul-kontron-n6310-s.dts"
+#include "imx6ul-kontron-bl.dts"
 
 / {
-	model = "Kontron N6310 S 43";
-	compatible = "kontron,imx6ul-n6310-s-43", "kontron,imx6ul-n6310-s",
-		     "kontron,imx6ul-n6310-som", "fsl,imx6ul";
+	model = "Kontron BL i.MX6UL 43 (N631X S 43)";
+	compatible = "kontron,bl-imx6ul-43", "kontron,bl-imx6ul",
+		     "kontron,sl-imx6ul", "fsl,imx6ul";
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm7 0 5000000>;
+		pwms = <&pwm7 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
 		status = "okay";
@@ -41,7 +41,6 @@
 };
 
 &pwm7 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm7>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl-common.dtsi
index 770f59b23102..f4c45e964daf 100644
--- a/arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl-common.dtsi
@@ -35,7 +35,7 @@
 
 	pwm-beeper {
 		compatible = "pwm-beeper";
-		pwms = <&pwm8 0 5000>;
+		pwms = <&pwm8 0 5000 0>;
 	};
 
 	reg_3v3: regulator-3v3 {
@@ -72,7 +72,6 @@
 &adc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_adc1>;
-	num-channels = <3>;
 	vref-supply = <&reg_vref_adc>;
 	status = "okay";
 };
@@ -153,7 +152,6 @@
 };
 
 &pwm8 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm8>;
 	status = "okay";
@@ -170,7 +168,6 @@
 	pinctrl-0 = <&pinctrl_uart2>;
 	linux,rs485-enabled-at-boot-time;
 	rs485-rx-during-tx;
-	rs485-rts-active-low;
 	uart-has-rtscts;
 	status = "okay";
 };
@@ -178,7 +175,7 @@
 &uart3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart3>;
-	fsl,uart-has-rtscts;
+	uart-has-rtscts;
 	status = "okay";
 };
 
@@ -273,7 +270,7 @@
 		>;
 	};
 
-	pinctrl_flexcan2: flexcan2grp{
+	pinctrl_flexcan2: flexcan2grp {
 		fsl,pins = <
 			MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX	0x1b020
 			MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX	0x1b020
@@ -353,7 +350,7 @@
 		>;
 	};
 
-	pinctrl_usbotg1: usbotg1 {
+	pinctrl_usbotg1: usbotg1grp {
 		fsl,pins = <
 			MX6UL_PAD_GPIO1_IO04__GPIO1_IO04	0x1b0b0
 		>;
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl.dts
index 5a3e06d6219b..dadf6d3d5f52 100644
--- a/arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-bl.dts
@@ -7,11 +7,10 @@
 
 /dts-v1/;
 
-#include "imx6ul-kontron-n6310-som.dtsi"
-#include "imx6ul-kontron-n6x1x-s.dtsi"
+#include "imx6ul-kontron-sl.dtsi"
+#include "imx6ul-kontron-bl-common.dtsi"
 
 / {
-	model = "Kontron N6310 S";
-	compatible = "kontron,imx6ul-n6310-s", "kontron,imx6ul-n6310-som",
-		     "fsl,imx6ul";
+	model = "Kontron BL i.MX6UL (N631X S)";
+	compatible = "kontron,bl-imx6ul", "kontron,sl-imx6ul", "fsl,imx6ul";
 };
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-sl-common.dtsi
index 2a449a3c1ae2..4c0ac4d4df68 100644
--- a/arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-sl-common.dtsi
@@ -11,6 +11,11 @@
 	chosen {
 		stdout-path = &uart4;
 	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x10000000>;
+		device_type = "memory";
+	};
 };
 
 &ecspi2 {
@@ -19,10 +24,31 @@
 	pinctrl-0 = <&pinctrl_ecspi2>;
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		compatible = "mxicy,mx25v8035f", "jedec,spi-nor";
-		spi-max-frequency = <50000000>;
 		reg = <0>;
+		spi-max-frequency = <50000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				reg = <0x0 0xf0000>;
+				label = "u-boot";
+			};
+
+			partition@f0000 {
+				reg = <0xf0000 0x8000>;
+				label = "env";
+			};
+
+			partition@f8000 {
+				reg = <0xf8000 0x8000>;
+				label = "env_redundant";
+			};
+		};
 	};
 };
 
@@ -55,6 +81,16 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_qspi>;
 	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "spi-nand";
+		spi-max-frequency = <104000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		reg = <0>;
+	};
 };
 
 &wdog1 {
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-sl.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-sl.dtsi
new file mode 100644
index 000000000000..0580d043e5ae
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-kontron-sl.dtsi
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#include "imx6ul.dtsi"
+#include "imx6ul-kontron-sl-common.dtsi"
+
+/ {
+	model = "Kontron SL i.MX6UL (N631X SOM)";
+	compatible = "kontron,sl-imx6ul", "fsl,imx6ul";
+};
diff --git a/arch/arm/boot/dts/imx6ul-liteboard.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-liteboard.dts
index 1d863a16bcf0..5e62272acfba 100644
--- a/arch/arm/boot/dts/imx6ul-liteboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-liteboard.dts
@@ -100,7 +100,7 @@
 		>;
 	};
 
-	pinctrl_usb_otg1_vbus: usb-otg1-vbus {
+	pinctrl_usb_otg1_vbus: usb-otg1-vbus-grp {
 		fsl,pins = <
 			MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08	0x79
 		>;
diff --git a/arch/arm/boot/dts/imx6ul-litesom.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-litesom.dtsi
index 8d6893210842..8d6893210842 100644
--- a/arch/arm/boot/dts/imx6ul-litesom.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-litesom.dtsi
diff --git a/arch/arm/boot/dts/imx6ul-opos6ul.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-opos6ul.dtsi
index 6ce84f92b027..6ce84f92b027 100644
--- a/arch/arm/boot/dts/imx6ul-opos6ul.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-opos6ul.dtsi
diff --git a/arch/arm/boot/dts/imx6ul-opos6uldev.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-opos6uldev.dts
index 375b98d7205a..375b98d7205a 100644
--- a/arch/arm/boot/dts/imx6ul-opos6uldev.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-opos6uldev.dts
diff --git a/arch/arm/boot/dts/imx6ul-phytec-phycore-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-phycore-som.dtsi
index 3cddc68917a0..a3ea1b208462 100644
--- a/arch/arm/boot/dts/imx6ul-phytec-phycore-som.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-phycore-som.dtsi
@@ -30,7 +30,7 @@
 		pinctrl-0 = <&pinctrl_gpioleds_som>;
 		compatible = "gpio-leds";
 
-		phycore-green {
+		led-phycore-green {
 			gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
@@ -102,6 +102,10 @@
 	status = "disabled";
 };
 
+&wdog1 {
+	fsl,suspend-in-wait;
+};
+
 &iomuxc {
 	pinctrl_enet1: enet1grp {
 		fsl,pins = <
diff --git a/arch/arm/boot/dts/imx6ul-phytec-segin-ff-rdk-emmc.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin-ff-rdk-emmc.dts
index cfc744f8fcad..cfc744f8fcad 100644
--- a/arch/arm/boot/dts/imx6ul-phytec-segin-ff-rdk-emmc.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin-ff-rdk-emmc.dts
diff --git a/arch/arm/boot/dts/imx6ul-phytec-segin-ff-rdk-nand.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin-ff-rdk-nand.dts
index 607eddc5030f..607eddc5030f 100644
--- a/arch/arm/boot/dts/imx6ul-phytec-segin-ff-rdk-nand.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin-ff-rdk-nand.dts
diff --git a/arch/arm/boot/dts/imx6ul-phytec-segin-peb-av-02.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin-peb-av-02.dtsi
index 7cda6944501d..c6064f4c679b 100644
--- a/arch/arm/boot/dts/imx6ul-phytec-segin-peb-av-02.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin-peb-av-02.dtsi
@@ -11,7 +11,7 @@
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <5>;
 		power-supply = <&reg_backlight_en>;
-		pwms = <&pwm3 0 5000000>;
+		pwms = <&pwm3 0 5000000 0>;
 		status = "disabled";
 	};
 
@@ -61,7 +61,7 @@
 		wakeup-source;
 		status = "disabled";
 
-		stmpe_touchscreen {
+		touchscreen {
 			compatible = "st,stmpe-ts";
 			st,sample-time = <4>;
 			st,mod-12b = <1>;
@@ -72,8 +72,8 @@
 			st,settling = <2>;
 			st,fraction-z = <7>;
 			st,i-drive = <1>;
-			touchscreen-inverted-x = <1>;
-			touchscreen-inverted-y = <1>;
+			touchscreen-inverted-x;
+			touchscreen-inverted-y;
 		};
 	};
 };
@@ -91,7 +91,6 @@
 };
 
 &pwm3 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "disabled";
diff --git a/arch/arm/boot/dts/imx6ul-phytec-segin-peb-eval-01.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin-peb-eval-01.dtsi
index 2f3fd32a1167..113485e3397a 100644
--- a/arch/arm/boot/dts/imx6ul-phytec-segin-peb-eval-01.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin-peb-eval-01.dtsi
@@ -8,12 +8,12 @@
 
 / {
 	gpio_keys: gpio-keys {
-		compatible = "gpio-key";
+		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_keys>;
 		status = "disabled";
 
-		power {
+		key-power {
 			label = "Power Button";
 			gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -29,13 +29,13 @@
 
 		user-led1 {
 			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "gpio";
+			linux,default-trigger = "none";
 			default-state = "on";
 		};
 
 		user-led2 {
 			gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "gpio";
+			linux,default-trigger = "none";
 			default-state = "on";
 		};
 	};
diff --git a/arch/arm/boot/dts/imx6ul-phytec-segin-peb-wlbt-05.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin-peb-wlbt-05.dtsi
index 04477fd4b9a9..4a45fb784ff7 100644
--- a/arch/arm/boot/dts/imx6ul-phytec-segin-peb-wlbt-05.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin-peb-wlbt-05.dtsi
@@ -31,7 +31,7 @@
 		>;
 	};
 
-	pinctrl_uart2_bt: uart2grp-bt {
+	pinctrl_uart2_bt: uart2-bt-grp {
 		fsl,pins = <
 			MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX   0x17059
 			MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX   0x17059
@@ -40,7 +40,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_wl: usdhc2grp-wl {
+	pinctrl_usdhc2_wl: usdhc2-wl-grp {
 		fsl,pins = <
 			MX6UL_PAD_LCD_DATA18__USDHC2_CMD    0x10051
 			MX6UL_PAD_LCD_DATA19__USDHC2_CLK    0x10061
diff --git a/arch/arm/boot/dts/imx6ul-phytec-segin.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin.dtsi
index 0d4ba9494cf2..bef5eb38a90d 100644
--- a/arch/arm/boot/dts/imx6ul-phytec-segin.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-phytec-segin.dtsi
@@ -83,11 +83,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_adc1>;
 	vref-supply = <&reg_adc1_vref_3v3>;
-	/*
-	 * driver can not separate a specific channel so we request 4 channels
-	 * here - we need only the fourth channel
-	 */
-	num-channels = <4>;
 	status = "disabled";
 };
 
@@ -224,7 +219,7 @@
 		>;
 	};
 
-	pinctrl_flexcan1: flexcan1 {
+	pinctrl_flexcan1: flexcan1grp {
 		fsl,pins = <
 			MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX	0x0b0b0
 			MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX	0x0b0b0
@@ -280,7 +275,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+	pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp {
 		fsl,pins = <
 			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170b9
 			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100b9
@@ -291,7 +286,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+	pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
 		fsl,pins = <
 			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170f9
 			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100f9
diff --git a/arch/arm/boot/dts/imx6ul-pico-dwarf.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-pico-dwarf.dts
index 162dc259edc8..fb206c1d8aca 100644
--- a/arch/arm/boot/dts/imx6ul-pico-dwarf.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-pico-dwarf.dts
@@ -32,7 +32,7 @@
 };
 
 &i2c2 {
-	clock_frequency = <100000>;
+	clock-frequency = <100000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
@@ -40,6 +40,7 @@
 	sgtl5000: audio-codec@a {
 		reg = <0x0a>;
 		compatible = "fsl,sgtl5000";
+		#sound-dai-cells = <0>;
 		clocks = <&sys_mclk>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_3p3v>;
diff --git a/arch/arm/boot/dts/imx6ul-pico-hobbit.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-pico-hobbit.dts
index 09f7ffa9ad8c..bf7dbb4f1f3e 100644
--- a/arch/arm/boot/dts/imx6ul-pico-hobbit.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-pico-hobbit.dts
@@ -51,6 +51,7 @@
 	sgtl5000: codec@a {
 		reg = <0x0a>;
 		compatible = "fsl,sgtl5000";
+		#sound-dai-cells = <0>;
 		clocks = <&sys_mclk>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_3p3v>;
diff --git a/arch/arm/boot/dts/imx6ul-pico-pi.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-pico-pi.dts
index 6cd7d5877d20..6cfc943a8fa3 100644
--- a/arch/arm/boot/dts/imx6ul-pico-pi.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-pico-pi.dts
@@ -51,6 +51,7 @@
 	sgtl5000: codec@a {
 		reg = <0x0a>;
 		compatible = "fsl,sgtl5000";
+		#sound-dai-cells = <0>;
 		clocks = <&sys_mclk>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_3p3v>;
diff --git a/arch/arm/boot/dts/imx6ul-pico.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-pico.dtsi
index 357ffb2f5ad6..9fa5225994e3 100644
--- a/arch/arm/boot/dts/imx6ul-pico.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-pico.dtsi
@@ -22,7 +22,7 @@
 
 	backlight: backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm3 0 5000000>;
+		pwms = <&pwm3 0 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
 		status = "okay";
@@ -76,6 +76,7 @@
 	panel {
 		compatible = "vxt,vl050-8048nt-c01";
 		backlight = <&backlight>;
+		power-supply = <&reg_3p3v>;
 
 		port {
 			panel_in: endpoint {
@@ -121,6 +122,8 @@
 			max-speed = <100>;
 			interrupt-parent = <&gpio5>;
 			interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			clock-names = "rmii-ref";
 		};
 	};
 };
@@ -131,7 +134,7 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	pmic: pfuze3000@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze3000";
 		reg = <0x08>;
 
@@ -175,7 +178,6 @@
 };
 
 &pwm3 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6ul-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx6ul-pinfunc.h
index 380d2db13a9b..380d2db13a9b 100644
--- a/arch/arm/boot/dts/imx6ul-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-pinfunc.h
diff --git a/arch/arm/boot/dts/imx6ul-prti6g.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-prti6g.dts
index c18390f238e1..c3c50f51a5a8 100644
--- a/arch/arm/boot/dts/imx6ul-prti6g.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-prti6g.dts
@@ -26,6 +26,7 @@
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <50000000>;
+		clock-output-names = "enet1_ref_pad";
 	};
 
 	leds {
@@ -60,6 +61,13 @@
 	status = "okay";
 };
 
+&clks {
+	clocks = <&ckil>, <&osc>, <&ipp_di0>, <&ipp_di1>, <&clock_ksz8081_out>;
+	clock-names = "ckil", "osc", "ipp_di0", "ipp_di1", "enet1_ref_pad";
+	assigned-clocks = <&clks IMX6UL_CLK_ENET1_REF_SEL>;
+	assigned-clock-parents = <&clock_ksz8081_out>;
+};
+
 &ecspi1 {
 	cs-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
@@ -85,12 +93,6 @@
 	pinctrl-0 = <&pinctrl_eth1>;
 	phy-mode = "rmii";
 	phy-handle = <&rmii_phy>;
-	clocks = <&clks IMX6UL_CLK_ENET>,
-		 <&clks IMX6UL_CLK_ENET_AHB>,
-		 <&clks IMX6UL_CLK_ENET_PTP>,
-		 <&clock_ksz8081_out>;
-	clock-names = "ipg", "ahb", "ptp",
-		      "enet_clk_ref";
 	status = "okay";
 
 	mdio {
@@ -175,6 +177,7 @@
 
 &usbotg1 {
 	dr_mode = "host";
+	over-current-active-low;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul-common.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul-common.dtsi
new file mode 100644
index 000000000000..2dd635a615cb
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul-common.dtsi
@@ -0,0 +1,216 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/*
+ * Common for
+ * - TQMa6ULx
+ * - TQMa6ULxL
+ * - TQMa6ULLx
+ * - TQMa6ULLxL
+ */
+
+/ {
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;
+	};
+};
+
+&i2c4 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	pinctrl-1 = <&pinctrl_i2c4_recovery>;
+	scl-gpios = <&gpio1 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio1 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	pfuze3000: pmic@8 {
+		compatible = "fsl,pfuze3000";
+		reg = <0x08>;
+
+		regulators {
+			reg_sw1a: sw1a {
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-ramp-delay = <6250>;
+				/* not used */
+			};
+
+			reg_sw1b_core: sw1b {
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1475000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			reg_sw2: sw2 {
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			reg_sw3_ddr: sw3 {
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1650000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_swbst: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+				/* not used */
+			};
+
+			reg_snvs_3v0: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vrefddr: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vccsd: vccsd {
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			reg_v33_3v3: v33 {
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			reg_vldo1_3v3: vldo1 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				/* not used */
+			};
+
+			reg_vldo2: vldo2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+				/* not used */
+			};
+
+			reg_vldo3: vldo3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				/* not used */
+			};
+
+			reg_vldo4: vldo4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+		};
+	};
+
+	jc42_1a: eeprom-temperature@1a {
+		compatible = "nxp,se97b", "jedec,jc-42.4-temp";
+		reg = <0x1a>;
+	};
+
+	m24c64_50: eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	m24c02_52: eeprom@52 {
+		compatible = "nxp,se97b", "atmel,24c02";
+		reg = <0x52>;
+		pagesize = <16>;
+		read-only;
+	};
+
+	rtc0: rtc@68 {
+		compatible = "dallas,ds1339";
+		reg = <0x68>;
+	};
+};
+
+&gpio4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pmic>;
+
+	/*
+	 * PMIC & temperature sensor IRQ
+	 * Both do currently not use IRQ
+	 * potentially dangerous if used on baseboard
+	 */
+	pmic-int-hog {
+		gpio-hog;
+		gpios = <24 0>;
+		input;
+	};
+};
+
+&qspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_qspi>;
+	status = "okay";
+
+	flash0: flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <33000000>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
+		vcc-supply = <&reg_vldo4>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+		};
+	};
+};
+
+/* eMMC */
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz" , "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+
+	bus-width = <8>;
+	disable-wp;
+	non-removable;
+	no-sdio;
+	no-sd;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_TX_DATA__I2C4_SCL	0x4001b8b0
+			MX6UL_PAD_UART2_RX_DATA__I2C4_SDA	0x4001b8b0
+		>;
+	};
+
+	pinctrl_i2c4_recovery: i2c4recoverygrp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20	0x4001b8b0
+			MX6UL_PAD_UART2_RX_DATA__GPIO1_IO21	0x4001b8b0
+		>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			/* PMIC irq */
+			MX6UL_PAD_CSI_DATA03__GPIO4_IO24	0x1b099
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul1-mba6ulx.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul1-mba6ulx.dts
new file mode 100644
index 000000000000..2e7b96e7b791
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul1-mba6ulx.dts
@@ -0,0 +1,56 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ul-tqma6ul2.dtsi"
+#include "mba6ulx.dtsi"
+#include "imx6ul-tqma6ul1.dtsi"
+
+/ {
+	model = "TQ-Systems TQMa6UL1 SoM on MBa6ULx board";
+	compatible = "tq,imx6ul-tqma6ul1-mba6ulx", "tq,imx6ul-tqma6ul1", "fsl,imx6ul";
+};
+
+/*
+ * Note: can2 and fec2 are enabled on mba6ulx level (for i.MX6ULG2 usage)
+ * and need to be disabled here again
+ */
+&can2 {
+	status = "disabled";
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>, <&pinctrl_enet1_mdc>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			max-speed = <100>;
+			reg = <0>;
+		};
+	};
+};
+
+&fec2 {
+	/delete-property/ phy-handle;
+	/delete-node/ mdio;
+};
+
+&iomuxc {
+	pinctrl_enet1_mdc: enet1mdcgrp {
+		fsl,pins = <
+			/* mdio */
+			MX6UL_PAD_GPIO1_IO07__ENET1_MDC		0x1b0b0
+			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO	0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul1.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul1.dtsi
new file mode 100644
index 000000000000..79c8c5529135
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul1.dtsi
@@ -0,0 +1,35 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/ {
+	model = "TQ-Systems TQMa6UL1 SoM";
+	compatible = "tq,imx6ul-tqma6ul1", "fsl,imx6ul";
+};
+
+/*
+ * There are no module specific differences compared to TQMa6UL2,
+ * only external interfaces differ
+ */
+
+/*
+ * Devices not available on i.MX6ULG1 and should not be enabled on
+ * mainboard level (again)
+ */
+&can2 {
+	status = "disabled";
+};
+
+&csi {
+	status = "disabled";
+};
+
+&fec2 {
+	status = "disabled";
+};
+
+&lcdif {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul2-mba6ulx.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul2-mba6ulx.dts
new file mode 100644
index 000000000000..0757df2b8f48
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul2-mba6ulx.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ul-tqma6ul2.dtsi"
+#include "mba6ulx.dtsi"
+
+/ {
+	model = "TQ-Systems TQMa6ULx SoM on MBa6ULx board";
+	compatible = "tq,imx6ul-tqma6ul2-mba6ulx", "tq,imx6ul-tqma6ul2", "fsl,imx6ul";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul2.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul2.dtsi
new file mode 100644
index 000000000000..e2e95dd92263
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul2.dtsi
@@ -0,0 +1,71 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include "imx6ul.dtsi"
+#include "imx6ul-tqma6ul-common.dtsi"
+#include "imx6ul-tqma6ulx-common.dtsi"
+
+/ {
+	model = "TQ-Systems TQMa6UL2 SoM";
+	compatible = "tq,imx6ul-tqma6ul2", "fsl,imx6ul";
+};
+
+&usdhc2 {
+	fsl,tuning-step = <6>;
+};
+
+&iomuxc {
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x00017051
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x00017051
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x00017051
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x00017051
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x00017051
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x00017051
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x00017051
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x00017051
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x00017051
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x00017051
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x000170e1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x000170f1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x000170f1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x000170f1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x000170f1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x000170f1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x000170f1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x000170f1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x000170f1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x000170f1
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x000170f1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x000170e1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x000170e1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x000170e1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x000170e1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x000170e1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x000170e1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x000170e1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x000170e1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x000170e1
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul2l-mba6ulx.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul2l-mba6ulx.dts
new file mode 100644
index 000000000000..9d9b6b744a1c
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul2l-mba6ulx.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ul-tqma6ul2l.dtsi"
+#include "mba6ulx.dtsi"
+
+/ {
+	model = "TQ Systems TQMa6UL2L SoM on MBa6ULx board";
+	compatible = "tq,imx6ul-tqma6ul2l-mba6ulx", "tq,imx6ul-tqma6ul2l", "fsl,imx6ul";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul2l.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul2l.dtsi
new file mode 100644
index 000000000000..4b87e2dc70dc
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ul2l.dtsi
@@ -0,0 +1,71 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include "imx6ul.dtsi"
+#include "imx6ul-tqma6ul-common.dtsi"
+#include "imx6ul-tqma6ulxl-common.dtsi"
+
+/ {
+	model = "TQ-Systems TQMa6UL2L SoM";
+	compatible = "tq,imx6ul-tqma6ul2l", "fsl,imx6ul";
+};
+
+&usdhc2 {
+	fsl,tuning-step = <6>;
+};
+
+&iomuxc {
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x00017051
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x00017051
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x00017051
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x00017051
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x00017051
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x00017051
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x00017051
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x00017051
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x00017051
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x00017051
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x000170e1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x000170f1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x000170f1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x000170f1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x000170f1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x000170f1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x000170f1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x000170f1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x000170f1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x000170f1
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x000170f9
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x000170f1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x000170f1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x000170f1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x000170f1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x000170f1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x000170f1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x000170f1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x000170f1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x000170f1
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ulx-common.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ulx-common.dtsi
new file mode 100644
index 000000000000..5afb9046c202
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ulx-common.dtsi
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/*
+ * Common for
+ * - TQMa6ULx
+ * - TQMa6ULLx
+ */
+
+&m24c64_50 {
+	vcc-supply = <&reg_sw2>;
+};
+
+&m24c02_52 {
+	vcc-supply = <&reg_sw2>;
+};
+
+&reg_sw2 {
+	regulator-boot-on;
+	regulator-always-on;
+};
+
+/* eMMC */
+&usdhc2 {
+	vmmc-supply = <&reg_sw2>;
+	vqmmc-supply = <&reg_vldo4>;
+};
+
+&iomuxc {
+	pinctrl_qspi: qspigrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK      0x70b9
+			MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70b9
+			MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01   0x70b9
+			MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02   0x70b9
+			MX6UL_PAD_NAND_CLE__QSPI_A_DATA03     0x70b9
+			MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B      0x70a1
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ulxl-common.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ulxl-common.dtsi
new file mode 100644
index 000000000000..ba84a4f70ebd
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-tqma6ulxl-common.dtsi
@@ -0,0 +1,48 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/*
+ * Common for
+ * - TQMa6ULxL
+ * - TQMa6ULLxL
+ */
+
+/ {
+	reg_vin: reg-vin {
+		compatible = "regulator-fixed";
+		regulator-name = "VIN";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+};
+
+&m24c64_50 {
+	vcc-supply = <&reg_vin>;
+};
+
+&m24c02_52 {
+	vcc-supply = <&reg_vin>;
+};
+
+/* eMMC */
+&usdhc2 {
+	vmmc-supply = <&reg_vin>;
+	vqmmc-supply = <&reg_vldo4>;
+};
+
+&iomuxc {
+	pinctrl_qspi: qspigrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK      0x70a9
+			MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70a9
+			MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01   0x70a9
+			MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02   0x70a9
+			MX6UL_PAD_NAND_CLE__QSPI_A_DATA03     0x70a9
+			MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B      0x70a1
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-tx6ul-0010.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-tx6ul-0010.dts
new file mode 100644
index 000000000000..188f3a2a312f
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-tx6ul-0010.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2015 Lothar Waßmann <LW@KARO-electronics.de>
+ */
+
+/dts-v1/;
+#include "imx6ul.dtsi"
+#include "imx6ul-tx6ul.dtsi"
+
+/ {
+	model = "Ka-Ro electronics TXUL-0010 Module";
+	compatible = "karo,imx6ul-tx6ul", "fsl,imx6ul";
+
+	aliases {
+		/delete-property/ mmc1;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-tx6ul-0011.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-tx6ul-0011.dts
new file mode 100644
index 000000000000..247a0aab7791
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-tx6ul-0011.dts
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright 2015 Lothar Waßmann <LW@KARO-electronics.de>
+ */
+
+/dts-v1/;
+#include "imx6ul.dtsi"
+#include "imx6ul-tx6ul.dtsi"
+
+/ {
+	model = "Ka-Ro electronics TXUL-0011 Module";
+	compatible = "karo,imx6ul-tx6ul", "fsl,imx6ul";
+
+	aliases {
+		mmc0 = &usdhc2;
+		mmc1 = &usdhc1;
+	};
+};
+
+&gpmi {
+	status = "disabled";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	bus-width = <4>;
+	no-1-8-v;
+	non-removable;
+	fsl,wp-controller;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ul-tx6ul-mainboard.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-tx6ul-mainboard.dts
index 92ac0edcb608..84b45542814e 100644
--- a/arch/arm/boot/dts/imx6ul-tx6ul-mainboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-tx6ul-mainboard.dts
@@ -1,42 +1,6 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
 /*
  * Copyright 2015 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 /dts-v1/;
@@ -133,7 +97,7 @@
 	pinctrl-0 = <&pinctrl_disp0_3>;
 };
 
-&reg_usbotg_vbus{
+&reg_usbotg_vbus {
 	status = "disabled";
 };
 
@@ -198,7 +162,7 @@
 		>;
 	};
 
-	pinctrl_disp0_3: disp0grp-3 {
+	pinctrl_disp0_3: disp0-3-grp {
 		fsl,pins = <
 			MX6UL_PAD_LCD_CLK__LCDIF_CLK		0x10 /* LSCLK */
 			MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE	0x10 /* OE_ACD */
diff --git a/arch/arm/boot/dts/imx6ul-tx6ul.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-tx6ul.dtsi
index c485d058e079..1992dfb53b45 100644
--- a/arch/arm/boot/dts/imx6ul-tx6ul.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-tx6ul.dtsi
@@ -1,42 +1,6 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
 /*
  * Copyright 2015 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 #include <dt-bindings/gpio/gpio.h>
@@ -108,16 +72,14 @@
 		default-brightness-level = <50>;
 	};
 
-	i2c_gpio: i2c-gpio {
+	i2c_gpio: i2c {
 		compatible = "i2c-gpio";
 		#address-cells = <1>;
 		#size-cells = <0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_i2c_gpio>;
-		gpios = <
-			&gpio5 1 GPIO_ACTIVE_HIGH /* SDA */
-			&gpio5 0 GPIO_ACTIVE_HIGH /* SCL */
-		>;
+		sda-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+		scl-gpios = <&gpio5 0 GPIO_ACTIVE_HIGH>;
 		clock-frequency = <400000>;
 		status = "okay";
 
@@ -131,7 +93,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		user_led: user {
+		user_led: led-user {
 			label = "Heartbeat";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_led>;
@@ -212,15 +174,15 @@
 		enable-active-high;
 	};
 
-	spi_gpio: spi-gpio {
+	spi_gpio: spi {
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "spi-gpio";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_spi_gpio>;
-		gpio-mosi = <&gpio1 30 GPIO_ACTIVE_HIGH>;
-		gpio-miso = <&gpio1 31 GPIO_ACTIVE_HIGH>;
-		gpio-sck = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
+		sck-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
 		num-chipselects = <2>;
 		cs-gpios = <
 			&gpio1 29 GPIO_ACTIVE_HIGH
@@ -284,7 +246,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet1_mdio &pinctrl_etnphy0_rst>;
 	phy-mode = "rmii";
-	phy-reset-gpios = <&gpio5 6 GPIO_ACTIVE_LOW>;
 	phy-supply = <&reg_3v3_etn>;
 	phy-handle = <&etnphy0>;
 	status = "okay";
@@ -300,6 +261,11 @@
 			pinctrl-0 = <&pinctrl_etnphy0_int>;
 			interrupt-parent = <&gpio5>;
 			interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+			reset-gpios = <&gpio5 6 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <100>;
+			reset-deassert-us = <25000>;
+			/* Energy detect sometimes causes link failures */
+			smsc,disable-energy-detect;
 			status = "okay";
 		};
 
@@ -310,6 +276,9 @@
 			pinctrl-0 = <&pinctrl_etnphy1_int>;
 			interrupt-parent = <&gpio4>;
 			interrupts = <27 IRQ_TYPE_EDGE_FALLING>;
+			reset-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <100>;
+			reset-deassert-us = <25000>;
 			status = "okay";
 		};
 	};
@@ -319,7 +288,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet2 &pinctrl_etnphy1_rst>;
 	phy-mode = "rmii";
-	phy-reset-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>;
 	phy-supply = <&reg_3v3_etn>;
 	phy-handle = <&etnphy1>;
 	status = "disabled";
@@ -407,7 +375,7 @@
 		status = "okay";
 
 		display-timings {
-			VGA {
+			timing-vga {
 				clock-frequency = <25200000>;
 				hactive = <640>;
 				vactive = <480>;
@@ -423,7 +391,7 @@
 				pixelclk-active = <1>;
 			};
 
-			ETV570 {
+			timing-etv570 {
 				clock-frequency = <25200000>;
 				hactive = <640>;
 				vactive = <480>;
@@ -439,7 +407,7 @@
 				pixelclk-active = <1>;
 			};
 
-			ET0350 {
+			timing-et0350 {
 				clock-frequency = <6413760>;
 				hactive = <320>;
 				vactive = <240>;
@@ -455,7 +423,7 @@
 				pixelclk-active = <1>;
 			};
 
-			ET0430 {
+			timing-et0430 {
 				clock-frequency = <9009000>;
 				hactive = <480>;
 				vactive = <272>;
@@ -471,7 +439,7 @@
 				pixelclk-active = <0>;
 			};
 
-			ET0500 {
+			timing-et0500 {
 				clock-frequency = <33264000>;
 				hactive = <800>;
 				vactive = <480>;
@@ -487,7 +455,7 @@
 				pixelclk-active = <1>;
 			};
 
-			ET0700 { /* same as ET0500 */
+			timing-et0700 { /* same as ET0500 */
 				clock-frequency = <33264000>;
 				hactive = <800>;
 				vactive = <480>;
@@ -503,7 +471,7 @@
 				pixelclk-active = <1>;
 			};
 
-			ETQ570 {
+			timing-etq570 {
 				clock-frequency = <6596040>;
 				hactive = <320>;
 				vactive = <240>;
@@ -580,19 +548,13 @@
 };
 
 &iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_hog>;
-
-	pinctrl_hog: hoggrp {
-	};
-
 	pinctrl_led: ledgrp {
 		fsl,pins = <
 			MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09	0x0b0b0 /* LED */
 		>;
 	};
 
-	pinctrl_disp0_1: disp0grp-1 {
+	pinctrl_disp0_1: disp0-1-grp {
 		fsl,pins = <
 			MX6UL_PAD_LCD_CLK__LCDIF_CLK		0x10 /* LSCLK */
 			MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE	0x10 /* OE_ACD */
@@ -625,7 +587,7 @@
 		>;
 	};
 
-	pinctrl_disp0_2: disp0grp-2 {
+	pinctrl_disp0_2: disp0-2-grp {
 		fsl,pins = <
 			MX6UL_PAD_LCD_CLK__LCDIF_CLK		0x10 /* LSCLK */
 			MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE	0x10 /* OE_ACD */
@@ -715,25 +677,25 @@
 		>;
 	};
 
-	pinctrl_etnphy0_int: etnphy-intgrp-0 {
+	pinctrl_etnphy0_int: etnphy-int-0-grp {
 		fsl,pins = <
 			MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x0b0b0 /* ETN PHY INT */
 		>;
 	};
 
-	pinctrl_etnphy0_rst: etnphy-rstgrp-0 {
+	pinctrl_etnphy0_rst: etnphy-rst-0-grp {
 		fsl,pins = <
 			MX6UL_PAD_SNVS_TAMPER6__GPIO5_IO06	0x0b0b0 /* ETN PHY RESET */
 		>;
 	};
 
-	pinctrl_etnphy1_int: etnphy-intgrp-1 {
+	pinctrl_etnphy1_int: etnphy-int-1-grp {
 		fsl,pins = <
 			MX6UL_PAD_CSI_DATA06__GPIO4_IO27	0x0b0b0 /* ETN PHY INT */
 		>;
 	};
 
-	pinctrl_etnphy1_rst: etnphy-rstgrp-1 {
+	pinctrl_etnphy1_rst: etnphy-rst-1-grp {
 		fsl,pins = <
 			MX6UL_PAD_CSI_DATA07__GPIO4_IO28	0x0b0b0 /* ETN PHY RESET */
 		>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-var-som-concerto.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-var-som-concerto.dts
new file mode 100644
index 000000000000..9ff3b374a2b3
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-var-som-concerto.dts
@@ -0,0 +1,320 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Support for Variscite MX6 Concerto Carrier board with the VAR-SOM-MX6UL
+ * Variscite SoM mounted on it
+ *
+ * Copyright 2019 Variscite Ltd.
+ * Copyright 2025 Bootlin
+ */
+
+#include "imx6ul-var-som.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Variscite VAR-SOM-MX6UL Concerto Board";
+	compatible = "variscite,mx6ulconcerto", "variscite,var-som-imx6ul", "fsl,imx6ul";
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_key_back>, <&pinctrl_gpio_key_wakeup>;
+
+		key-back {
+			gpios = <&gpio4 14 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_BACK>;
+		};
+
+		key-wakeup {
+			gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WAKEUP>;
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+
+		led-0 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			label = "gpled2";
+			gpios = <&gpio1 25 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	status = "okay";
+};
+
+&fec1 {
+	status = "disabled";
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2>, <&pinctrl_enet2_gpio>, <&pinctrl_enet2_mdio>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy1>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@3 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <3>;
+			clocks = <&rmii_ref_clk>;
+			clock-names = "rmii-ref";
+			reset-gpios = <&gpio5 5 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <100000>;
+			micrel,led-mode = <0>;
+			micrel,rmii-reference-clock-select-25-mhz = <1>;
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	rtc@68 {
+		/*
+		 * To actually use this interrupt
+		 * connect pins J14.8 & J14.10 on the Concerto-Board.
+		 */
+		compatible = "dallas,ds1337";
+		reg = <0x68>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
+	};
+};
+
+&iomuxc {
+	pinctrl_enet2: enet2grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00	0x1b0b0
+			MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01	0x1b0b0
+			MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	0x4001b031
+		>;
+	};
+
+	pinctrl_enet2_gpio: enet2-gpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x1b0b0 /* fec2 reset */
+		>;
+	};
+
+	pinctrl_enet2_mdio: enet2-mdiogrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO06__ENET2_MDIO	0x1b0b0
+			MX6UL_PAD_GPIO1_IO07__ENET2_MDC		0x1b0b0
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX	0x1b020
+			MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX	0x1b020
+		>;
+	};
+
+	pinctrl_gpio_key_back: gpio-key-backgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_CE1_B__GPIO4_IO14	0x17059
+		>;
+	};
+
+	pinctrl_gpio_leds: gpio-ledsgrp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_RX_DATA__GPIO1_IO25	0x1b0b0	/* GPLED2 */
+		>;
+	};
+
+	pinctrl_gpio_key_wakeup: gpio-keys-wakeupgrp {
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER8__GPIO5_IO08	0x17059
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_PIXCLK__I2C1_SCL		0x4001b8b0
+			MX6UL_PAD_CSI_MCLK__I2C1_SDA		0x4001b8b0
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO05__PWM4_OUT		0x110b0
+		>;
+	};
+
+	pinctrl_rtc: rtcgrp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_MOD__GPIO1_IO10		0x1b0b0 /* RTC alarm IRQ */
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA00__UART5_DCE_TX	0x1b0b1
+			MX6UL_PAD_CSI_DATA01__UART5_DCE_RX	0x1b0b1
+			MX6UL_PAD_GPIO1_IO09__UART5_DCE_CTS	0x1b0b1
+			MX6UL_PAD_GPIO1_IO08__UART5_DCE_RTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_usb_otg1_id: usbotg1idgrp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_TX_DATA__ANATOP_OTG1_ID	0x17059
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x17059
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170b9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100b9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170b9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170b9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170b9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170f9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100f9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170f9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170f9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170f9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170f9
+		>;
+	};
+
+	pinctrl_usdhc1_gpio: usdhc1-gpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__GPIO1_IO00	0x1b0b1 /* CD */
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO01__WDOG1_WDOG_B	0x78b0
+		>;
+	};
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+	status = "okay";
+};
+
+&snvs_pwrkey {
+	status = "disabled";
+};
+
+&snvs_rtc {
+	status = "disabled";
+};
+
+&tsc {
+	/*
+	 * Conflics with wdog1 ext-reset-output & SD CD pins,
+	 * so we keep it disabled by default.
+	 */
+	status = "disabled";
+};
+
+/* Console UART */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+/* ttymxc4 UART */
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_otg1_id>;
+	dr_mode = "otg";
+	disable-over-current;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>, <&pinctrl_usdhc1_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>, <&pinctrl_usdhc1_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>, <&pinctrl_usdhc1_gpio>;
+	cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	wakeup-source;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	/*
+	 * To actually use ext-reset-output
+	 * connect pins J17.3 & J17.8 on the Concerto-Board
+	 */
+	fsl,ext-reset-output;
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-var-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-var-som.dtsi
new file mode 100644
index 000000000000..4e536e0252de
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-var-som.dtsi
@@ -0,0 +1,233 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Support for Variscite VAR-SOM-MX6UL Module
+ *
+ * Copyright 2019 Variscite Ltd.
+ * Copyright 2025 Bootlin
+ */
+
+/dts-v1/;
+
+#include "imx6ul.dtsi"
+#include <dt-bindings/clock/imx6ul-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Variscite VAR-SOM-MX6UL module";
+	compatible = "variscite,var-som-imx6ul", "fsl,imx6ul";
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reg_gpio_dvfs: reg-gpio-dvfs {
+		compatible = "regulator-gpio";
+		regulator-min-microvolt = <1300000>;
+		regulator-max-microvolt = <1400000>;
+		regulator-name = "gpio_dvfs";
+		regulator-type = "voltage";
+		gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+		states = <1300000 0x1
+			  1400000 0x0>;
+	};
+
+	rmii_ref_clk: rmii-ref-clk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+		clock-output-names = "rmii-ref";
+	};
+};
+
+&clks {
+	assigned-clocks = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
+	assigned-clock-rates = <786432000>;
+};
+
+&cpu0 {
+	dc-supply = <&reg_gpio_dvfs>;
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>, <&pinctrl_enet1_gpio>, <&pinctrl_enet1_mdio>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy0>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			clocks = <&rmii_ref_clk>;
+			clock-names = "rmii-ref";
+			reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <100000>;
+			micrel,led-mode = <1>;
+			micrel,rmii-reference-clock-select-25-mhz = <1>;
+		};
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1	0x4001b031
+		>;
+	};
+
+	pinctrl_enet1_gpio: enet1-gpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x1b0b0 /* fec1 reset */
+		>;
+	};
+
+	pinctrl_enet1_mdio: enet1-mdiogrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO	0x1b0b0
+			MX6UL_PAD_GPIO1_IO07__ENET1_MDC		0x1b0b0
+		>;
+	};
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04	0x1b0b0	/* BT Enable */
+			MX6UL_PAD_SNVS_TAMPER6__GPIO5_IO06	0x03029	/* WLAN Enable */
+		>;
+	};
+
+	pinctrl_sai2: sai2grp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK	0x17088
+			MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC	0x17088
+			MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA	0x11088
+			MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA	0x11088
+			MX6UL_PAD_JTAG_TMS__SAI2_MCLK		0x17088
+		>;
+	};
+
+	pinctrl_tsc: tscgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01	0xb0
+			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0xb0
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0xb0
+			MX6UL_PAD_GPIO1_IO04__GPIO1_IO04	0xb0
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX	0x1b0b1
+			MX6UL_PAD_UART2_CTS_B__UART2_DCE_CTS	0x1b0b1
+			MX6UL_PAD_UART2_RTS_B__UART2_DCE_RTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x10069
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x17059
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x17059
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x17059
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x17059
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x17059
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x17059
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x17059
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x17059
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x17059
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x100b9
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x170b9
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x170b9
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x170b9
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x170b9
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x170b9
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x170b9
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x170b9
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x170b9
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x100f9
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x170f9
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x170f9
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x170f9
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x170f9
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x170f9
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x170f9
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x170f9
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x170f9
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x170f9
+		>;
+	};
+};
+
+&pxp {
+	status = "okay";
+};
+
+&sai2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai2>;
+	assigned-clocks = <&clks IMX6UL_CLK_SAI2_SEL>,
+			  <&clks IMX6UL_CLK_SAI2>;
+	assigned-clock-parents = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
+	assigned-clock-rates = <0>, <12288000>;
+	fsl,sai-mclk-direction-output;
+	status = "okay";
+};
+
+&snvs_poweroff {
+	status = "okay";
+};
+
+&tsc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_tsc>;
+	xnur-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+	measure-delay-time = <0xffff>;
+	pre-charge-time = <0xfff>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	keep-power-in-suspend;
+	wakeup-source;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ul.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
index afeec01f6522..6de224dd2bb9 100644
--- a/arch/arm/boot/dts/imx6ul.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
@@ -64,20 +64,18 @@
 			clock-frequency = <696000000>;
 			clock-latency = <61036>; /* two CLK32 periods */
 			#cooling-cells = <2>;
-			operating-points = <
+			operating-points =
 				/* kHz	uV */
-				696000	1275000
-				528000	1175000
-				396000	1025000
-				198000	950000
-			>;
-			fsl,soc-operating-points = <
+				<696000	1275000>,
+				<528000	1175000>,
+				<396000	1025000>,
+				<198000	950000>;
+			fsl,soc-operating-points =
 				/* KHz	uV */
-				696000	1275000
-				528000	1175000
-				396000	1175000
-				198000	1175000
-			>;
+				<696000	1275000>,
+				<528000	1175000>,
+				<396000	1175000>,
+				<198000	1175000>;
 			clocks = <&clks IMX6UL_CLK_ARM>,
 				 <&clks IMX6UL_CLK_PLL2_BUS>,
 				 <&clks IMX6UL_CLK_PLL2_PFD2>,
@@ -139,7 +137,7 @@
 		interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
@@ -149,6 +147,9 @@
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 		};
 
 		intc: interrupt-controller@a01000 {
@@ -163,14 +164,13 @@
 			      <0x00a06000 0x2000>;
 		};
 
-		dma_apbh: dma-apbh@1804000 {
+		dma_apbh: dma-controller@1804000 {
 			compatible = "fsl,imx6q-dma-apbh", "fsl,imx28-dma-apbh";
 			reg = <0x01804000 0x2000>;
 			interrupts = <0 13 IRQ_TYPE_LEVEL_HIGH>,
 				     <0 13 IRQ_TYPE_LEVEL_HIGH>,
 				     <0 13 IRQ_TYPE_LEVEL_HIGH>,
 				     <0 13 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3";
 			#dma-cells = <1>;
 			dma-channels = <4>;
 			clocks = <&clks IMX6UL_CLK_APBHDMA>;
@@ -179,7 +179,7 @@
 		gpmi: nand-controller@1806000 {
 			compatible = "fsl,imx6q-gpmi-nand";
 			#address-cells = <1>;
-			#size-cells = <1>;
+			#size-cells = <0>;
 			reg = <0x01806000 0x2000>, <0x01808000 0x2000>;
 			reg-names = "gpmi-nand", "bch";
 			interrupts = <0 15 IRQ_TYPE_LEVEL_HIGH>;
@@ -274,6 +274,8 @@
 					clocks = <&clks IMX6UL_CLK_UART7_IPG>,
 						 <&clks IMX6UL_CLK_UART7_SERIAL>;
 					clock-names = "ipg", "per";
+					dmas = <&sdma 43 4 0>, <&sdma 44 4 0>;
+					dma-names = "rx", "tx";
 					status = "disabled";
 				};
 
@@ -285,6 +287,8 @@
 					clocks = <&clks IMX6UL_CLK_UART1_IPG>,
 						 <&clks IMX6UL_CLK_UART1_SERIAL>;
 					clock-names = "ipg", "per";
+					dmas = <&sdma 25 4 0>, <&sdma 26 4 0>;
+					dma-names = "rx", "tx";
 					status = "disabled";
 				};
 
@@ -296,6 +300,8 @@
 					clocks = <&clks IMX6UL_CLK_UART8_IPG>,
 						 <&clks IMX6UL_CLK_UART8_SERIAL>;
 					clock-names = "ipg", "per";
+					dmas = <&sdma 45 4 0>, <&sdma 46 4 0>;
+					dma-names = "rx", "tx";
 					status = "disabled";
 				};
 
@@ -364,13 +370,13 @@
 						<&sdma 20 23 1>, <&sdma 21 23 1>, <&sdma 22 23 1>;
 					dma-names = "rxa", "rxb", "rxc",
 						    "txa", "txb", "txc";
-					fsl,asrc-rate  = <48000>;
+					fsl,asrc-rate = <48000>;
 					fsl,asrc-width = <16>;
 					status = "okay";
 				};
 			};
 
-			tsc: tsc@2040000 {
+			tsc: touchscreen@2040000 {
 				compatible = "fsl,imx6ul-tsc";
 				reg = <0x02040000 0x4000>, <0x0219c000 0x4000>;
 				interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
@@ -531,19 +537,20 @@
 				clocks = <&clks IMX6UL_CLK_ENET>,
 					 <&clks IMX6UL_CLK_ENET_AHB>,
 					 <&clks IMX6UL_CLK_ENET_PTP>,
-					 <&clks IMX6UL_CLK_ENET2_REF_125M>,
-					 <&clks IMX6UL_CLK_ENET2_REF_125M>;
+					 <&clks IMX6UL_CLK_ENET2_REF_SEL>;
 				clock-names = "ipg", "ahb", "ptp",
-					      "enet_clk_ref", "enet_out";
+					      "enet_clk_ref";
 				fsl,num-tx-queues = <1>;
 				fsl,num-rx-queues = <1>;
 				fsl,stop-mode = <&gpr 0x10 4>;
 				fsl,magic-packet;
+				nvmem-cells = <&fec2_mac_addr>;
+				nvmem-cell-names = "mac-address";
 				status = "disabled";
 			};
 
 			kpp: keypad@20b8000 {
-				compatible = "fsl,imx6ul-kpp", "fsl,imx6q-kpp", "fsl,imx21-kpp";
+				compatible = "fsl,imx6ul-kpp", "fsl,imx21-kpp";
 				reg = <0x020b8000 0x4000>;
 				interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6UL_CLK_KPP>;
@@ -639,6 +646,7 @@
 					nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
 					nvmem-cell-names = "calib", "temp_grade";
 					clocks = <&clks IMX6UL_CLK_PLL3_USB_OTG>;
+					#thermal-sensor-cells = <0>;
 				};
 			};
 
@@ -720,6 +728,18 @@
 				#interrupt-cells = <3>;
 				interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-parent = <&intc>;
+				clocks = <&clks IMX6UL_CLK_IPG>;
+				clock-names = "ipg";
+
+				pgc {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					power-domain@0 {
+						reg = <0>;
+						#power-domain-cells = <0>;
+					};
+				};
 			};
 
 			iomuxc: pinctrl@20e0000 {
@@ -743,7 +763,7 @@
 				status = "disabled";
 			};
 
-			sdma: sdma@20ec000 {
+			sdma: dma-controller@20ec000 {
 				compatible = "fsl,imx6ul-sdma", "fsl,imx6q-sdma",
 					     "fsl,imx35-sdma";
 				reg = <0x020ec000 0x4000>;
@@ -844,7 +864,6 @@
 				clocks = <&clks IMX6UL_CLK_USBOH3>;
 				fsl,usbphy = <&usbphy1>;
 				fsl,usbmisc = <&usbmisc 0>;
-				fsl,anatop = <&anatop>;
 				ahb-burst-config = <0x0>;
 				tx-burst-size-dword = <0x10>;
 				rx-burst-size-dword = <0x10>;
@@ -879,14 +898,15 @@
 				clocks = <&clks IMX6UL_CLK_ENET>,
 					 <&clks IMX6UL_CLK_ENET_AHB>,
 					 <&clks IMX6UL_CLK_ENET_PTP>,
-					 <&clks IMX6UL_CLK_ENET_REF>,
-					 <&clks IMX6UL_CLK_ENET_REF>;
+					 <&clks IMX6UL_CLK_ENET1_REF_SEL>;
 				clock-names = "ipg", "ahb", "ptp",
-					      "enet_clk_ref", "enet_out";
+					      "enet_clk_ref";
 				fsl,num-tx-queues = <1>;
 				fsl,num-rx-queues = <1>;
 				fsl,stop-mode = <&gpr 0x10 3>;
 				fsl,magic-packet;
+				nvmem-cells = <&fec1_mac_addr>;
+				nvmem-cell-names = "mac-address";
 				status = "disabled";
 			};
 
@@ -923,7 +943,6 @@
 				reg = <0x02198000 0x4000>;
 				interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6UL_CLK_ADC1>;
-				num-channels = <2>;
 				clock-names = "adc";
 				fsl,adck-max-frequency = <30000000>, <40000000>,
 							 <20000000>;
@@ -966,7 +985,7 @@
 				clocks = <&clks IMX6UL_CLK_MMDC_P0_IPG>;
 			};
 
-			weim: weim@21b8000 {
+			weim: memory-controller@21b8000 {
 				#address-cells = <2>;
 				#size-cells = <1>;
 				compatible = "fsl,imx6ul-weim", "fsl,imx6q-weim";
@@ -995,10 +1014,18 @@
 				cpu_speed_grade: speed-grade@10 {
 					reg = <0x10 4>;
 				};
+
+				fec1_mac_addr: mac-addr@88 {
+					reg = <0x88 6>;
+				};
+
+				fec2_mac_addr: mac-addr@8e {
+					reg = <0x8e 6>;
+				};
 			};
 
 			csi: csi@21c4000 {
-				compatible = "fsl,imx6ul-csi", "fsl,imx7-csi";
+				compatible = "fsl,imx6ul-csi";
 				reg = <0x021c4000 0x4000>;
 				interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6UL_CLK_CSI>;
@@ -1007,7 +1034,7 @@
 			};
 
 			lcdif: lcdif@21c8000 {
-				compatible = "fsl,imx6ul-lcdif", "fsl,imx28-lcdif";
+				compatible = "fsl,imx6ul-lcdif", "fsl,imx6sx-lcdif";
 				reg = <0x021c8000 0x4000>;
 				interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6UL_CLK_LCDIF_PIX>,
@@ -1028,7 +1055,7 @@
 			qspi: spi@21e0000 {
 				#address-cells = <1>;
 				#size-cells = <0>;
-				compatible = "fsl,imx6ul-qspi", "fsl,imx6sx-qspi";
+				compatible = "fsl,imx6ul-qspi";
 				reg = <0x021e0000 0x4000>, <0x60000000 0x10000000>;
 				reg-names = "QuadSPI", "QuadSPI-memory";
 				interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
@@ -1054,6 +1081,8 @@
 				clocks = <&clks IMX6UL_CLK_UART2_IPG>,
 					 <&clks IMX6UL_CLK_UART2_SERIAL>;
 				clock-names = "ipg", "per";
+				dmas = <&sdma 27 4 0>, <&sdma 28 4 0>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 
@@ -1065,6 +1094,8 @@
 				clocks = <&clks IMX6UL_CLK_UART3_IPG>,
 					 <&clks IMX6UL_CLK_UART3_SERIAL>;
 				clock-names = "ipg", "per";
+				dmas = <&sdma 29 4 0>, <&sdma 30 4 0>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 
@@ -1076,6 +1107,8 @@
 				clocks = <&clks IMX6UL_CLK_UART4_IPG>,
 					 <&clks IMX6UL_CLK_UART4_SERIAL>;
 				clock-names = "ipg", "per";
+				dmas = <&sdma 31 4 0>, <&sdma 32 4 0>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 
@@ -1087,6 +1120,8 @@
 				clocks = <&clks IMX6UL_CLK_UART5_IPG>,
 					 <&clks IMX6UL_CLK_UART5_SERIAL>;
 				clock-names = "ipg", "per";
+				dmas = <&sdma 33 4 0>, <&sdma 34 4 0>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 
@@ -1108,6 +1143,8 @@
 				clocks = <&clks IMX6UL_CLK_UART6_IPG>,
 					 <&clks IMX6UL_CLK_UART6_SERIAL>;
 				clock-names = "ipg", "per";
+				dmas = <&sdma 0 4 0>, <&sdma 47 4 0>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 		};
diff --git a/arch/arm/boot/dts/imx6ull-14x14-evk.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-14x14-evk.dts
index 74aaa8a56a3d..74aaa8a56a3d 100644
--- a/arch/arm/boot/dts/imx6ull-14x14-evk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-14x14-evk.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-aster.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-aster.dts
new file mode 100644
index 000000000000..3e0897c3a296
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-aster.dts
@@ -0,0 +1,60 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2017-2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-nonwifi.dtsi"
+#include "imx6ull-colibri-aster.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 256/512MB on Colibri Aster";
+	compatible = "toradex,colibri-imx6ull-aster",
+		     "toradex,colibri-imx6ull",
+		     "fsl,imx6ull";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+/* PWM <B> */
+&pwm5 {
+	/* Pin already used by atmel_mxt_ts touchscreen */
+	status = "disabled";
+};
+
+/* PWM <C> */
+&pwm6 {
+	/* Pin already used by atmel_mxt_ts touchscreen */
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-aster.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-aster.dtsi
new file mode 100644
index 000000000000..e75dad0f0e23
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-aster.dtsi
@@ -0,0 +1,147 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2017-2022 Toradex
+ */
+
+/ {
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_snvs_gpiokeys>;
+
+		key-power {
+			label = "Wake-Up";
+			gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+			linux,code = <KEY_WAKEUP>;
+			debounce-interval = <10>;
+			wakeup-source;
+		};
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_usbh_vbus: regulator-usbh-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh_reg>;
+		regulator-name = "VCC_USB[1-4]";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
+		vin-supply = <&reg_5v0>;
+	};
+};
+
+&adc1 {
+	status = "okay";
+};
+
+&ecspi1 {
+	status = "okay";
+
+	num-cs = <2>;
+	cs-gpios = <
+		&gpio3 26 GPIO_ACTIVE_HIGH /* SODIMM 86 LCD_DATA21 */
+		&gpio4 28 GPIO_ACTIVE_HIGH /* SODIMM 65 CSI_DATA07 */
+	>;
+};
+
+/*
+ * Following SODIMM Pins should not be accessed as GPIO on Aster board:
+ * 134 - AIN5_SCL (no connection)
+ * 127 - Voltage Level Translator OE# signal (IC11 and IC12)
+ *
+ * To configure GPIO to LED5, please disable FEC2 and uncomment the following:
+ *	&iomuxc {
+ *		pinctrl-names = "default";
+ *		pinctrl-0 = <
+ *			&pinctrl_gpio1
+ *			&pinctrl_gpio2
+ *			&pinctrl_gpio3
+ *			&pinctrl_gpio4
+ *			&pinctrl_gpio6 - for non-WiFi modules only
+ *			&pinctrl_gpio7
+ *			&pinctrl_gpio_aster
+ *		>;
+ *
+ *		pinctrl_gpio_aster: gpio-aster {
+ *			fsl,pins = <
+ *				MX6UL_PAD_GPIO1_IO07__GPIO1_IO07    0x1b0b0
+ *			>;
+ *		};
+ *  };
+ */
+
+&i2c1 {
+	status = "okay";
+
+	m41t0m6: rtc@68 {
+		compatible = "st,m41t0";
+		reg = <0x68>;
+	};
+};
+
+/* PWM <A> */
+&pwm4 {
+	status = "okay";
+};
+
+/* PWM <B> */
+&pwm5 {
+	status = "okay";
+};
+
+/* PWM <C> */
+&pwm6 {
+	status = "okay";
+};
+
+/* PWM <D> */
+&pwm7 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&usbotg1 {
+	disable-over-current;
+	vbus-supply = <&reg_usbh_vbus>;
+	status = "okay";
+};
+
+&usbotg2 {
+	disable-over-current;
+	vbus-supply = <&reg_usbh_vbus>;
+	status = "okay";
+};
+
+&usdhc1 {
+	vmmc-supply = <&reg_3v3>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-aster.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-aster.dts
new file mode 100644
index 000000000000..b2cdf4877718
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-aster.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-emmc-nonwifi.dtsi"
+#include "imx6ull-colibri-aster.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 1GB (eMMC) on Colibri Aster";
+	compatible = "toradex,colibri-imx6ull-emmc-aster",
+		     "toradex,colibri-imx6ull-emmc",
+		     "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/imx6ull-colibri-emmc-eval-v3.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-eval-v3.dts
index 61b93cb040c7..2dc16c54fc78 100644
--- a/arch/arm/boot/dts/imx6ull-colibri-emmc-eval-v3.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-eval-v3.dts
@@ -12,6 +12,5 @@
 	model = "Toradex Colibri iMX6ULL 1GB (eMMC) on Colibri Evaluation Board V3";
 	compatible = "toradex,colibri-imx6ull-emmc-eval",
 		     "toradex,colibri-imx6ull-emmc",
-		     "toradex,colibri-imx6ull",
 		     "fsl,imx6ull";
 };
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-iris-v2.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-iris-v2.dts
new file mode 100644
index 000000000000..9bae08fb7f85
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-iris-v2.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-emmc-nonwifi.dtsi"
+#include "imx6ull-colibri-iris-v2.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 1G (eMMC) on Colibri Iris V2";
+	compatible = "toradex,colibri-imx6ull-emmc-iris-v2",
+		     "toradex,colibri-imx6ull-emmc",
+		     "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-iris.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-iris.dts
new file mode 100644
index 000000000000..0b1603ff9420
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-iris.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-emmc-nonwifi.dtsi"
+#include "imx6ull-colibri-iris.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 1GB (eMMC) on Colibri Iris";
+	compatible = "toradex,colibri-imx6ull-emmc-iris",
+		     "toradex,colibri-imx6ull-emmc",
+		     "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/imx6ull-colibri-emmc-nonwifi.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-nonwifi.dtsi
index a099abfdfa27..ea238525d5c0 100644
--- a/arch/arm/boot/dts/imx6ull-colibri-emmc-nonwifi.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-emmc-nonwifi.dtsi
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2021 Toradex
+ * Copyright 2022 Toradex
  */
 
 #include "imx6ull-colibri.dtsi"
@@ -8,7 +8,7 @@
 / {
 	aliases {
 		mmc0 = &usdhc2; /* eMMC */
-		mmc1 = &usdhc1; /* MMC 4bit slot */
+		mmc1 = &usdhc1; /* MMC 4-bit slot */
 	};
 
 	memory@80000000 {
@@ -154,6 +154,7 @@
 			  "SODIMM_127";
 };
 
+/* NAND */
 &gpmi {
 	status = "disabled";
 };
@@ -170,6 +171,7 @@
 	pinctrl-0 = <&pinctrl_snvs_gpio1 &pinctrl_snvs_gpio3>;
 };
 
+/* eMMC */
 &usdhc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc2emmc>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-eval-v3.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-eval-v3.dts
new file mode 100644
index 000000000000..c5bc255b21e1
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-eval-v3.dts
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018-2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-nonwifi.dtsi"
+#include "imx6ull-colibri-eval-v3.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 256/512MB on Colibri Evaluation Board V3";
+	compatible = "toradex,colibri-imx6ull-eval", "toradex,colibri-imx6ull", "fsl,imx6ull";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-eval-v3.dtsi
index a78849fd2afa..692ef26fbab3 100644
--- a/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-eval-v3.dtsi
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2017 Toradex AG
+ * Copyright 2017-2022 Toradex
  */
 
 / {
@@ -8,20 +8,6 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_snvs_gpiokeys>;
-
-		power {
-			label = "Wake-Up";
-			gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
-			linux,code = <KEY_WAKEUP>;
-			debounce-interval = <10>;
-			wakeup-source;
-		};
-	};
-
 	/* fixed crystal dedicated to mcp2515 */
 	clk16m: clk16m {
 		compatible = "fixed-clock";
@@ -29,18 +15,6 @@
 		clock-frequency = <16000000>;
 	};
 
-	panel: panel {
-		compatible = "edt,et057090dhu";
-		backlight = <&bl>;
-		power-supply = <&reg_3v3>;
-
-		port {
-			panel_in: endpoint {
-				remote-endpoint = <&lcdif_out>;
-			};
-		};
-	};
-
 	reg_3v3: regulator-3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "3.3V";
@@ -71,14 +45,6 @@
 	status = "okay";
 };
 
-&bl {
-	brightness-levels = <0 4 8 16 32 64 128 255>;
-	default-brightness-level = <6>;
-	power-supply = <&reg_3v3>;
-	pwms = <&pwm4 0 5000000 1>;
-	status = "okay";
-};
-
 &ecspi1 {
 	status = "okay";
 
@@ -107,16 +73,6 @@
 	};
 };
 
-&lcdif {
-	status = "okay";
-
-	port {
-		lcdif_out: endpoint {
-			remote-endpoint = <&panel_in>;
-		};
-	};
-};
-
 /* PWM <A> */
 &pwm4 {
 	status = "okay";
@@ -150,29 +106,18 @@
 };
 
 &usbotg1 {
+	disable-over-current;
+	vbus-supply = <&reg_usbh_vbus>;
 	status = "okay";
 };
 
 &usbotg2 {
+	disable-over-current;
 	vbus-supply = <&reg_usbh_vbus>;
 	status = "okay";
 };
 
 &usdhc1 {
-	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
-	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_snvs_usdhc1_cd>;
-	pinctrl-1 = <&pinctrl_usdhc1_100mhz &pinctrl_snvs_usdhc1_cd>;
-	pinctrl-2 = <&pinctrl_usdhc1_200mhz &pinctrl_snvs_usdhc1_cd>;
-	pinctrl-3 = <&pinctrl_usdhc1 &pinctrl_snvs_usdhc1_sleep_cd>;
-	cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
-	disable-wp;
-	wakeup-source;
-	keep-power-in-suspend;
 	vmmc-supply = <&reg_3v3>;
-	vqmmc-supply = <&reg_sd1_vmmc>;
-	sd-uhs-sdr12;
-	sd-uhs-sdr25;
-	sd-uhs-sdr50;
-	sd-uhs-sdr104;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-iris-v2.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-iris-v2.dts
new file mode 100644
index 000000000000..f6b31118be17
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-iris-v2.dts
@@ -0,0 +1,105 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018-2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-nonwifi.dtsi"
+#include "imx6ull-colibri-iris-v2.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 256M/512B on Colibri Iris V2";
+	compatible = "toradex,colibri-imx6ull-iris-v2",
+		     "toradex,colibri-imx6ull",
+		     "fsl,imx6ull";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&gpio1 {
+	/* This turns the LVDS transceiver on */
+	lvds-power-on-hog {
+		gpio-hog;
+		gpios = <14 GPIO_ACTIVE_HIGH>; /* SODIMM 99 */
+		line-name = "LVDS_POWER_ON";
+		output-high;
+	};
+};
+
+&gpio2 {
+	/*
+	 * This switches the LVDS transceiver to the single-channel
+	 * output mode.
+	 */
+	lvds-ch-mode-hog {
+		gpio-hog;
+		gpios = <0 GPIO_ACTIVE_HIGH>; /* SODIMM 55 */
+		line-name = "LVDS_CH_MODE";
+		output-high;
+	};
+
+	/*
+	 * This switches the LVDS transceiver to the 24-bit RGB mode.
+	 */
+	lvds-rgb-mode-hog {
+		gpio-hog;
+		gpios = <1 GPIO_ACTIVE_HIGH>; /* SODIMM 63 */
+		line-name = "LVDS_RGB_MODE";
+		output-low;
+	};
+};
+
+&gpio5 {
+	/*
+	 * This switches the LVDS transceiver to VESA color mapping mode.
+	 */
+	lvds-color-map-hog {
+		gpio-hog;
+		gpios = <3 GPIO_ACTIVE_HIGH>; /* SODIMM 95 */
+		line-name = "LVDS_COLOR_MAP";
+		output-low;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+/* PWM <B> */
+&pwm5 {
+	/* Pin already used by atmel_mxt_ts touchscreen */
+	status = "disabled";
+};
+
+/* PWM <C> */
+&pwm6 {
+	/* Pin already used by atmel_mxt_ts touchscreen */
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-iris-v2.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-iris-v2.dtsi
new file mode 100644
index 000000000000..93649cad0cc0
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-iris-v2.dtsi
@@ -0,0 +1,27 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018-2022 Toradex
+ */
+
+#include "imx6ull-colibri-iris.dtsi"
+
+/ {
+	reg_3v3_vmmc: regulator-3v3-vmmc {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3_vmmc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <100>;
+		enable-active-high;
+	};
+};
+
+
+&usdhc1 {
+	cap-power-off-card;
+	vmmc-supply = <&reg_3v3_vmmc>;
+	/delete-property/ keep-power-in-suspend;
+	/delete-property/ no-1-8-v;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-iris.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-iris.dts
new file mode 100644
index 000000000000..2a0d0fc3b9d6
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-iris.dts
@@ -0,0 +1,40 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018-2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-nonwifi.dtsi"
+#include "imx6ull-colibri-iris.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 256/512MB on Colibri Iris";
+	compatible = "toradex,colibri-imx6ull-iris",
+		     "toradex,colibri-imx6ull",
+		     "fsl,imx6ull";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-iris.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-iris.dtsi
new file mode 100644
index 000000000000..bce6fbf230b3
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-iris.dtsi
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018-2022 Toradex
+ */
+
+/ {
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_snvs_gpiokeys>;
+
+		key-power {
+			label = "Wake-Up";
+			gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+			linux,code = <KEY_WAKEUP>;
+			debounce-interval = <10>;
+			wakeup-source;
+		};
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_usbh_vbus: regulator-usbh-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh_reg>;
+		regulator-name = "VCC_USB[1-4]";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
+		vin-supply = <&reg_5v0>;
+	};
+};
+
+&adc1 {
+	status = "okay";
+};
+
+&gpio1 {
+	/*
+	 * uart25_tx_on turns the UART transceiver on. If one wants to turn the
+	 * transceiver off, that property has to be deleted and the gpio handled
+	 * in userspace.
+	 * The same applies to uart1_tx_on.
+	 */
+	uart25_tx_on-hog {
+		gpio-hog;
+		gpios = <15 0>;
+		output-high;
+	};
+};
+
+&gpio2 {
+	uart1_tx_on-hog {
+		gpio-hog;
+		gpios = <7 0>;
+		output-high;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+
+	/* M41T0M6 real time clock on carrier board */
+	m41t0m6: rtc@68 {
+		compatible = "st,m41t0";
+		reg = <0x68>;
+	};
+};
+
+/* PWM <A> */
+&pwm4 {
+	status = "okay";
+};
+
+/* PWM <B> */
+&pwm5 {
+	status = "okay";
+};
+
+/* PWM <C> */
+&pwm6 {
+	status = "okay";
+};
+
+/* PWM <D> */
+&pwm7 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&usbotg1 {
+	disable-over-current;
+	vbus-supply = <&reg_usbh_vbus>;
+	status = "okay";
+};
+
+&usbotg2 {
+	disable-over-current;
+	vbus-supply = <&reg_usbh_vbus>;
+	status = "okay";
+};
+
+&usdhc1 {
+	vmmc-supply = <&reg_3v3>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-nonwifi.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-nonwifi.dtsi
new file mode 100644
index 000000000000..88901db255d6
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-nonwifi.dtsi
@@ -0,0 +1,161 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018-2022 Toradex
+ */
+
+#include "imx6ull-colibri.dtsi"
+
+/ {
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;
+	};
+};
+
+&gpio1 {
+	gpio-line-names = "SODIMM_8",
+			  "SODIMM_6",
+			  "SODIMM_129",
+			  "SODIMM_89",
+			  "SODIMM_19",
+			  "SODIMM_21",
+			  "UNUSABLE_SODIMM_180",
+			  "UNUSABLE_SODIMM_184",
+			  "SODIMM_4",
+			  "SODIMM_2",
+			  "SODIMM_106",
+			  "SODIMM_71",
+			  "SODIMM_23",
+			  "SODIMM_31",
+			  "SODIMM_99",
+			  "SODIMM_102",
+			  "SODIMM_33",
+			  "SODIMM_35",
+			  "SODIMM_25",
+			  "SODIMM_27",
+			  "SODIMM_36",
+			  "SODIMM_38",
+			  "SODIMM_32",
+			  "SODIMM_34",
+			  "SODIMM_135",
+			  "SODIMM_77",
+			  "SODIMM_100",
+			  "SODIMM_186",
+			  "SODIMM_196",
+			  "SODIMM_194";
+};
+
+&gpio2 {
+	gpio-line-names = "SODIMM_55",
+			  "SODIMM_63",
+			  "SODIMM_178",
+			  "SODIMM_188",
+			  "SODIMM_73",
+			  "SODIMM_30",
+			  "SODIMM_67",
+			  "SODIMM_104",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_190",
+			  "SODIMM_47",
+			  "SODIMM_192",
+			  "SODIMM_49",
+			  "SODIMM_51",
+			  "SODIMM_53";
+};
+
+&gpio3 {
+	gpio-line-names = "SODIMM_56",
+			  "SODIMM_44",
+			  "SODIMM_68",
+			  "SODIMM_82",
+			  "",
+			  "SODIMM_76",
+			  "SODIMM_70",
+			  "SODIMM_60",
+			  "SODIMM_58",
+			  "SODIMM_78",
+			  "SODIMM_72",
+			  "SODIMM_80",
+			  "SODIMM_46",
+			  "SODIMM_62",
+			  "SODIMM_48",
+			  "SODIMM_74",
+			  "SODIMM_50",
+			  "SODIMM_52",
+			  "SODIMM_54",
+			  "SODIMM_66",
+			  "SODIMM_64",
+			  "SODIMM_57",
+			  "SODIMM_61",
+			  "SODIMM_29",
+			  "SODIMM_37",
+			  "SODIMM_88",
+			  "SODIMM_86",
+			  "SODIMM_92",
+			  "SODIMM_90";
+};
+
+&gpio4 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_59",
+			  "",
+			  "",
+			  "SODIMM_133",
+			  "",
+			  "SODIMM_28",
+			  "SODIMM_75",
+			  "SODIMM_96",
+			  "SODIMM_81",
+			  "SODIMM_94",
+			  "SODIMM_101",
+			  "SODIMM_103",
+			  "SODIMM_79",
+			  "SODIMM_97",
+			  "SODIMM_69",
+			  "SODIMM_98",
+			  "SODIMM_85",
+			  "SODIMM_65";
+};
+
+&gpio5 {
+	gpio-line-names = "SODIMM_43",
+			  "SODIMM_45",
+			  "SODIMM_137",
+			  "SODIMM_95",
+			  "SODIMM_107",
+			  "SODIMM_131",
+			  "SODIMM_93",
+			  "",
+			  "SODIMM_138",
+			  "",
+			  "SODIMM_105",
+			  "SODIMM_127";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio1 &pinctrl_gpio2 &pinctrl_gpio3
+		&pinctrl_gpio4 &pinctrl_gpio6 &pinctrl_gpio7>;
+};
+
+&iomuxc_snvs {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_snvs_gpio1 &pinctrl_snvs_gpio3>;
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi-aster.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi-aster.dts
new file mode 100644
index 000000000000..d3bbd05da293
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi-aster.dts
@@ -0,0 +1,60 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2017-2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-wifi.dtsi"
+#include "imx6ull-colibri-aster.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 512MB on Colibri Aster";
+	compatible = "toradex,colibri-imx6ull-wifi-aster",
+		     "toradex,colibri-imx6ull-wifi",
+		     "fsl,imx6ull";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+/* PWM <B> */
+&pwm5 {
+	/* Pin already used by atmel_mxt_ts touchscreen */
+	status = "disabled";
+};
+
+/* PWM <C> */
+&pwm6 {
+	/* Pin already used by atmel_mxt_ts touchscreen */
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi-eval-v3.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi-eval-v3.dts
new file mode 100644
index 000000000000..0ac306c9cef2
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi-eval-v3.dts
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018-2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-wifi.dtsi"
+#include "imx6ull-colibri-eval-v3.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 512MB on Colibri Evaluation Board V3";
+	compatible = "toradex,colibri-imx6ull-wifi-eval", "toradex,colibri-imx6ull-wifi", "fsl,imx6ull";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi-iris-v2.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi-iris-v2.dts
new file mode 100644
index 000000000000..38cd52c45496
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi-iris-v2.dts
@@ -0,0 +1,89 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018-2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-wifi.dtsi"
+#include "imx6ull-colibri-iris-v2.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 512MB on Colibri Iris V2";
+	compatible = "toradex,colibri-imx6ull-wifi-iris-v2",
+		     "toradex,colibri-imx6ull-wifi",
+		     "fsl,imx6ull";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&gpio1 {
+	/* This turns the LVDS transceiver on */
+	lvds-power-on-hog {
+		gpio-hog;
+		gpios = <14 GPIO_ACTIVE_HIGH>; /* SODIMM 99 */
+		line-name = "LVDS_POWER_ON";
+		output-high;
+	};
+};
+
+&gpio2 {
+	/*
+	 * This switches the LVDS transceiver to the single-channel
+	 * output mode.
+	 */
+	lvds-ch-mode-hog {
+		gpio-hog;
+		gpios = <0 GPIO_ACTIVE_HIGH>; /* SODIMM 55 */
+		line-name = "LVDS_CH_MODE";
+		output-high;
+	};
+
+	/*
+	 * This switches the LVDS transceiver to the 24-bit RGB mode.
+	 */
+	lvds-rgb-mode-hog {
+		gpio-hog;
+		gpios = <1 GPIO_ACTIVE_HIGH>; /* SODIMM 63 */
+		line-name = "LVDS_RGB_MODE";
+		output-low;
+	};
+};
+
+&gpio5 {
+	/*
+	 * This switches the LVDS transceiver to VESA color mapping mode.
+	 */
+	lvds-color-map-hog {
+		gpio-hog;
+		gpios = <3 GPIO_ACTIVE_HIGH>; /* SODIMM 95 */
+		line-name = "LVDS_COLOR_MAP";
+		output-low;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi-iris.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi-iris.dts
new file mode 100644
index 000000000000..5f60df64f173
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi-iris.dts
@@ -0,0 +1,40 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018-2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-wifi.dtsi"
+#include "imx6ull-colibri-iris.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 512MB on Colibri Iris";
+	compatible = "toradex,colibri-imx6ull-wifi-iris",
+		     "toradex,colibri-imx6ull-wifi",
+		     "fsl,imx6ull";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi.dtsi
new file mode 100644
index 000000000000..db59ee6b1c86
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri-wifi.dtsi
@@ -0,0 +1,189 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018-2022 Toradex
+ */
+
+#include "imx6ull-colibri.dtsi"
+
+/ {
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	wifi_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_snvs_wifi_pdn>;
+		reset-gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&cpu0 {
+	clock-frequency = <792000000>;
+};
+
+&gpio1 {
+	gpio-line-names = "SODIMM_8",
+			  "SODIMM_6",
+			  "SODIMM_129",
+			  "",
+			  "SODIMM_19",
+			  "SODIMM_21",
+			  "UNUSABLE_SODIMM_180",
+			  "UNUSABLE_SODIMM_184",
+			  "SODIMM_4",
+			  "SODIMM_2",
+			  "SODIMM_106",
+			  "SODIMM_71",
+			  "SODIMM_23",
+			  "SODIMM_31",
+			  "SODIMM_99",
+			  "SODIMM_102",
+			  "SODIMM_33",
+			  "SODIMM_35",
+			  "SODIMM_25",
+			  "SODIMM_27",
+			  "SODIMM_36",
+			  "SODIMM_38",
+			  "SODIMM_32",
+			  "SODIMM_34",
+			  "SODIMM_135",
+			  "SODIMM_77",
+			  "SODIMM_100",
+			  "SODIMM_186",
+			  "SODIMM_196",
+			  "SODIMM_194";
+};
+
+&gpio2 {
+	gpio-line-names = "SODIMM_55",
+			  "SODIMM_63",
+			  "SODIMM_178",
+			  "SODIMM_188",
+			  "SODIMM_73",
+			  "SODIMM_30",
+			  "SODIMM_67",
+			  "SODIMM_104",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_190",
+			  "SODIMM_47",
+			  "SODIMM_192",
+			  "SODIMM_49",
+			  "SODIMM_51",
+			  "SODIMM_53";
+};
+
+&gpio3 {
+	gpio-line-names = "SODIMM_56",
+			  "SODIMM_44",
+			  "SODIMM_68",
+			  "SODIMM_82",
+			  "",
+			  "SODIMM_76",
+			  "SODIMM_70",
+			  "SODIMM_60",
+			  "SODIMM_58",
+			  "SODIMM_78",
+			  "SODIMM_72",
+			  "SODIMM_80",
+			  "SODIMM_46",
+			  "SODIMM_62",
+			  "SODIMM_48",
+			  "SODIMM_74",
+			  "SODIMM_50",
+			  "SODIMM_52",
+			  "SODIMM_54",
+			  "SODIMM_66",
+			  "SODIMM_64",
+			  "SODIMM_57",
+			  "SODIMM_61",
+			  "SODIMM_29",
+			  "SODIMM_37",
+			  "SODIMM_88",
+			  "SODIMM_86",
+			  "SODIMM_92",
+			  "SODIMM_90";
+};
+
+&gpio4 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_59",
+			  "",
+			  "",
+			  "SODIMM_133",
+			  "",
+			  "SODIMM_28",
+			  "SODIMM_75",
+			  "SODIMM_96",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_69",
+			  "SODIMM_98",
+			  "SODIMM_85",
+			  "SODIMM_65";
+};
+
+&gpio5 {
+	gpio-line-names = "SODIMM_43",
+			  "SODIMM_45",
+			  "SODIMM_137",
+			  "SODIMM_95",
+			  "SODIMM_107",
+			  "SODIMM_131",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_105";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio1 &pinctrl_gpio2 &pinctrl_gpio3
+		&pinctrl_gpio4 &pinctrl_gpio7>;
+
+};
+
+&iomuxc_snvs {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_snvs_gpio1>;
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	assigned-clocks = <&clks IMX6UL_CLK_USDHC2_SEL>, <&clks IMX6UL_CLK_USDHC2>;
+	assigned-clock-parents = <&clks IMX6UL_CLK_PLL2_PFD2>;
+	assigned-clock-rates = <0>, <198000000>;
+	cap-power-off-card;
+	keep-power-in-suspend;
+	max-frequency = <25000000>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	no-1-8-v;
+	non-removable;
+	vmmc-supply = <&reg_module_3v3>;
+	wakeup-source;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ull-colibri.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri.dtsi
index 7f35a06dff95..ec3c1e7301f4 100644
--- a/arch/arm/boot/dts/imx6ull-colibri.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-colibri.dtsi
@@ -1,24 +1,72 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2018-2021 Toradex
+ * Copyright 2018-2022 Toradex
  */
 
 #include "imx6ull.dtsi"
 
 / {
+	/* Ethernet aliases to ensure correct MAC addresses */
 	aliases {
 		ethernet0 = &fec2;
 		ethernet1 = &fec1;
 	};
 
-	bl: backlight {
+	backlight: backlight {
 		compatible = "pwm-backlight";
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+		enable-gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_bl_on>;
-		enable-gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
+		power-supply = <&reg_3v3>;
+		pwms = <&pwm4 0 5000000 1>;
 		status = "disabled";
 	};
 
+	connector {
+		compatible = "gpio-usb-b-connector", "usb-b-connector";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_snvs_usbc_det>;
+		id-gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>; /* SODIMM 137 / USBC_DET */
+		label = "USBC";
+		self-powered;
+		type = "micro";
+
+		port {
+			usb_dr_connector: endpoint {
+				remote-endpoint = <&usb1_drd_sw>;
+			};
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_snvs_gpiokeys>;
+
+		key-wakeup {
+			debounce-interval = <10>;
+			gpios = <&gpio5 1 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* SODIMM 45 */
+			label = "Wake-Up";
+			linux,code = <KEY_WAKEUP>;
+			wakeup-source;
+		};
+	};
+
+	panel_dpi: panel-dpi {
+		compatible = "edt,et057090dhu";
+		backlight = <&backlight>;
+		power-supply = <&reg_3v3>;
+		status = "disabled";
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcdif_out>;
+			};
+		};
+	};
+
 	reg_module_3v3: regulator-module-3v3 {
 		compatible = "regulator-fixed";
 		regulator-always-on;
@@ -35,9 +83,9 @@
 		regulator-max-microvolt = <3300000>;
 	};
 
-	reg_sd1_vmmc: regulator-sd1-vmmc {
+	reg_sd1_vqmmc: regulator-sd1-vqmmc {
 		compatible = "regulator-gpio";
-		gpio = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+		gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_snvs_reg_sd>;
 		regulator-always-on;
@@ -47,11 +95,23 @@
 		states = <1800000 0x1 3300000 0x0>;
 		vin-supply = <&reg_module_3v3>;
 	};
+
+	reg_eth_phy: regulator-eth-phy {
+		compatible = "regulator-fixed-clock";
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "+V3.3_ETH";
+		vin-supply = <&reg_module_3v3>;
+		clocks = <&clks IMX6UL_CLK_ENET2_REF_125M>;
+		startup-delay-us = <150000>;
+	};
 };
 
 &adc1 {
-	num-channels = <10>;
 	vref-supply = <&reg_module_3v3_avdd>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc1>;
 };
 
 &can1 {
@@ -73,12 +133,14 @@
 	pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1_cs>;
 };
 
+/* Ethernet */
 &fec2 {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&pinctrl_enet2>;
 	pinctrl-1 = <&pinctrl_enet2_sleep>;
 	phy-mode = "rmii";
 	phy-handle = <&ethphy1>;
+	phy-supply = <&reg_eth_phy>;
 	status = "okay";
 
 	mdio {
@@ -93,9 +155,11 @@
 	};
 };
 
+/* NAND */
 &gpmi {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	fsl,use-minimum-ecc;
 	nand-on-flash-bbt;
 	nand-ecc-mode = "hw";
 	nand-ecc-strength = <8>;
@@ -103,15 +167,35 @@
 	status = "okay";
 };
 
+/* I2C3_SDA/SCL on SODIMM 194/196 (e.g. RTC on carrier board) */
 &i2c1 {
 	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c1>;
 	pinctrl-1 = <&pinctrl_i2c1_gpio>;
 	sda-gpios = <&gpio1 29 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	scl-gpios = <&gpio1 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "disabled";
+
+	/* Atmel maxtouch controller */
+	atmel_mxt_ts: touchscreen@4a {
+		compatible = "atmel,maxtouch";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_atmel_conn &pinctrl_atmel_snvs_conn>;
+		reg = <0x4a>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <4 IRQ_TYPE_EDGE_FALLING>;       /* SODIMM 107 / INT */
+		reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;    /* SODIMM 106 / RST */
+		status = "disabled";
+	};
 };
 
+/*
+ * PWR_I2C: power I2C to audio codec, PMIC, temperature sensor and
+ * touch screen controller
+ */
 &i2c2 {
+	/* Use low frequency to compensate for the high pull-up values. */
+	clock-frequency = <40000>;
 	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c2>;
 	pinctrl-1 = <&pinctrl_i2c2_gpio>;
@@ -119,7 +203,7 @@
 	scl-gpios = <&gpio1 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 
-	ad7879@2c {
+	ad7879_ts: touchscreen@2c {
 		compatible = "adi,ad7879-1";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_snvs_ad7879_int>;
@@ -133,6 +217,7 @@
 		adi,median-filter-size = /bits/ 8 <2>;
 		adi,averaging = /bits/ 8 <1>;
 		adi,conversion-interval = /bits/ 8 <255>;
+		status = "disabled";
 	};
 };
 
@@ -140,23 +225,34 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_lcdif_dat
 		     &pinctrl_lcdif_ctrl>;
+	status = "disabled";
+
+	port {
+		lcdif_out: endpoint {
+			remote-endpoint = <&lcd_panel_in>;
+		};
+	};
 };
 
+/* PWM <A> */
 &pwm4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 };
 
+/* PWM <B> */
 &pwm5 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm5>;
 };
 
+/* PWM <C> */
 &pwm6 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm6>;
 };
 
+/* PWM <D> */
 &pwm7 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm7>;
@@ -170,6 +266,7 @@
 	status = "disabled";
 };
 
+/* Colibri UART_A */
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1 &pinctrl_uart1_ctrl1>;
@@ -177,6 +274,7 @@
 	fsl,dte-mode;
 };
 
+/* Colibri UART_B */
 &uart2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart2>;
@@ -184,27 +282,50 @@
 	fsl,dte-mode;
 };
 
+/* Colibri UART_C */
 &uart5 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart5>;
 	fsl,dte-mode;
 };
 
+/* Colibri USBC */
 &usbotg1 {
 	dr_mode = "otg";
 	srp-disable;
 	hnp-disable;
 	adp-disable;
+	usb-role-switch;
+
+	port {
+		usb1_drd_sw: endpoint {
+			remote-endpoint = <&usb_dr_connector>;
+		};
+	};
 };
 
+/* Colibri USBH */
 &usbotg2 {
 	dr_mode = "host";
 };
 
+/* Colibri MMC/SD */
 &usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_snvs_usdhc1_cd>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz &pinctrl_snvs_usdhc1_cd>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz &pinctrl_snvs_usdhc1_cd>;
+	pinctrl-3 = <&pinctrl_usdhc1 &pinctrl_snvs_usdhc1_cd_sleep>;
 	assigned-clocks = <&clks IMX6UL_CLK_USDHC1_SEL>, <&clks IMX6UL_CLK_USDHC1>;
 	assigned-clock-parents = <&clks IMX6UL_CLK_PLL2_PFD2>;
 	assigned-clock-rates = <0>, <198000000>;
+	bus-width = <4>;
+	cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; /* MMC_CD */
+	disable-wp;
+	keep-power-in-suspend;
+	no-1-8-v;
+	vqmmc-supply = <&reg_sd1_vqmmc>;
+	wakeup-source;
 };
 
 &wdog1 {
@@ -214,13 +335,35 @@
 };
 
 &iomuxc {
-	pinctrl_can_int: canint-grp {
+	pinctrl_adc1: adc1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__GPIO1_IO00        0x3000 /* SODIMM 8 */
+			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01        0x3000 /* SODIMM 6 */
+			MX6UL_PAD_GPIO1_IO08__GPIO1_IO08        0x3000 /* SODIMM 4 */
+			MX6UL_PAD_GPIO1_IO09__GPIO1_IO09        0x3000 /* SODIMM 2 */
+		>;
+	};
+
+	pinctrl_atmel_adap: atmeladapgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_DQS__GPIO4_IO16          0xb0a0  /* SODIMM 28 */
+			MX6UL_PAD_ENET1_TX_EN__GPIO2_IO05       0xb0a0  /* SODIMM 30 */
+		>;
+	};
+
+	pinctrl_atmel_conn: atmelconngrp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_MOD__GPIO1_IO10          0xb0a0  /* SODIMM 106 */
+		>;
+	};
+
+	pinctrl_can_int: canintgrp {
 		fsl,pins = <
 			MX6UL_PAD_ENET1_TX_DATA1__GPIO2_IO04	0x13010	/* SODIMM 73 */
 		>;
 	};
 
-	pinctrl_enet2: enet2-grp {
+	pinctrl_enet2: enet2grp {
 		fsl,pins = <
 			MX6UL_PAD_GPIO1_IO06__ENET2_MDIO	0x1b0b0
 			MX6UL_PAD_GPIO1_IO07__ENET2_MDC		0x1b0b0
@@ -235,7 +378,7 @@
 		>;
 	};
 
-	pinctrl_enet2_sleep: enet2sleepgrp {
+	pinctrl_enet2_sleep: enet2-sleepgrp {
 		fsl,pins = <
 			MX6UL_PAD_GPIO1_IO06__GPIO1_IO06	0x0
 			MX6UL_PAD_GPIO1_IO07__GPIO1_IO07	0x0
@@ -250,13 +393,13 @@
 		>;
 	};
 
-	pinctrl_ecspi1_cs: ecspi1-cs-grp {
+	pinctrl_ecspi1_cs: ecspi1csgrp {
 		fsl,pins = <
 			MX6UL_PAD_LCD_DATA21__GPIO3_IO26	0x70a0	/* SODIMM 86 */
 		>;
 	};
 
-	pinctrl_ecspi1: ecspi1-grp {
+	pinctrl_ecspi1: ecspi1grp {
 		fsl,pins = <
 			MX6UL_PAD_LCD_DATA20__ECSPI1_SCLK	0x000a0	/* SODIMM 88 */
 			MX6UL_PAD_LCD_DATA22__ECSPI1_MOSI	0x000a0 /* SODIMM 92 */
@@ -264,27 +407,27 @@
 		>;
 	};
 
-	pinctrl_flexcan1: flexcan1-grp {
+	pinctrl_flexcan1: flexcan1grp {
 		fsl,pins = <
 			MX6UL_PAD_ENET1_RX_DATA0__FLEXCAN1_TX	0x1b020
 			MX6UL_PAD_ENET1_RX_DATA1__FLEXCAN1_RX	0x1b020
 		>;
 	};
 
-	pinctrl_flexcan2: flexcan2-grp {
+	pinctrl_flexcan2: flexcan2grp {
 		fsl,pins = <
 			MX6UL_PAD_ENET1_TX_DATA0__FLEXCAN2_RX	0x1b020
 			MX6UL_PAD_ENET1_RX_EN__FLEXCAN2_TX	0x1b020
 		>;
 	};
 
-	pinctrl_gpio_bl_on: gpio-bl-on-grp {
+	pinctrl_gpio_bl_on: gpioblongrp {
 		fsl,pins = <
 			MX6UL_PAD_JTAG_TMS__GPIO1_IO11		0x30a0	/* SODIMM 71 */
 		>;
 	};
 
-	pinctrl_gpio1: gpio1-grp {
+	pinctrl_gpio1: gpio1grp {
 		fsl,pins = <
 			MX6UL_PAD_UART3_RX_DATA__GPIO1_IO25	0x10b0 /* SODIMM 77 */
 			MX6UL_PAD_JTAG_TCK__GPIO1_IO14		0x70a0 /* SODIMM 99 */
@@ -297,7 +440,7 @@
 		>;
 	};
 
-	pinctrl_gpio2: gpio2-grp { /* Camera */
+	pinctrl_gpio2: gpio2grp { /* Camera */
 		fsl,pins = <
 			MX6UL_PAD_CSI_DATA04__GPIO4_IO25	0x10b0 /* SODIMM 69 */
 			MX6UL_PAD_CSI_MCLK__GPIO4_IO17		0x10b0 /* SODIMM 75 */
@@ -307,26 +450,20 @@
 		>;
 	};
 
-	pinctrl_gpio3: gpio3-grp { /* CAN2 */
+	pinctrl_gpio3: gpio3grp { /* CAN2 */
 		fsl,pins = <
 			MX6UL_PAD_ENET1_RX_EN__GPIO2_IO02	0x10b0 /* SODIMM 178 */
 			MX6UL_PAD_ENET1_TX_DATA0__GPIO2_IO03	0x10b0 /* SODIMM 188 */
 		>;
 	};
 
-	pinctrl_gpio4: gpio4-grp {
+	pinctrl_gpio4: gpio4grp {
 		fsl,pins = <
 			MX6UL_PAD_CSI_DATA07__GPIO4_IO28	0x10b0 /* SODIMM 65 */
 		>;
 	};
 
-	pinctrl_gpio5: gpio5-grp { /* ATMEL MXT TOUCH */
-		fsl,pins = <
-			MX6UL_PAD_JTAG_MOD__GPIO1_IO10		0xb0a0 /* SODIMM 106 */
-		>;
-	};
-
-	pinctrl_gpio6: gpio6-grp { /* Wifi pins */
+	pinctrl_gpio6: gpio6grp { /* Wifi pins */
 		fsl,pins = <
 			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0x10b0 /* SODIMM 89 */
 			MX6UL_PAD_CSI_DATA02__GPIO4_IO23	0x10b0 /* SODIMM 79 */
@@ -338,7 +475,7 @@
 		>;
 	};
 
-	pinctrl_gpio7: gpio7-grp { /* CAN1 */
+	pinctrl_gpio7: gpio7grp { /* CAN1 */
 		fsl,pins = <
 			MX6UL_PAD_ENET1_RX_DATA0__GPIO2_IO00	0xb0b0/* SODIMM 55 */
 			MX6UL_PAD_ENET1_RX_DATA1__GPIO2_IO01	0xb0b0 /* SODIMM 63 */
@@ -347,9 +484,9 @@
 
 	/*
 	 * With an eMMC instead of a raw NAND device the following pins
-	 * are available at SODIMM pins
+	 * are available at SODIMM pins.
 	 */
-	pinctrl_gpmi_gpio: gpmi-gpio-grp {
+	pinctrl_gpmi_gpio: gpmigpiogrp {
 		fsl,pins = <
 			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x10b0 /* SODIMM 140 */
 			MX6UL_PAD_NAND_CE0_B__GPIO4_IO13	0x10b0 /* SODIMM 144 */
@@ -358,7 +495,7 @@
 		>;
 	};
 
-	pinctrl_gpmi_nand: gpmi-nand-grp {
+	pinctrl_gpmi_nand: gpminandgrp {
 		fsl,pins = <
 			MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00	0x100a9
 			MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01	0x100a9
@@ -377,35 +514,35 @@
 		>;
 	};
 
-	pinctrl_i2c1: i2c1-grp {
+	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
 			MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0	/* SODIMM 196 */
 			MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0	/* SODIMM 194 */
 		>;
 	};
 
-	pinctrl_i2c1_gpio: i2c1-gpio-grp {
+	pinctrl_i2c1_gpio: i2c1-gpiogrp {
 		fsl,pins = <
 			MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x4001b8b0	/* SODIMM 196 */
 			MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x4001b8b0	/* SODIMM 194 */
 		>;
 	};
 
-	pinctrl_i2c2: i2c2-grp {
+	pinctrl_i2c2: i2c2grp {
 		fsl,pins = <
-			MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001b8b0
-			MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001b8b0
+			MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001f8b0
+			MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001f8b0
 		>;
 	};
 
-	pinctrl_i2c2_gpio: i2c2-gpio-grp {
+	pinctrl_i2c2_gpio: i2c2-gpiogrp {
 		fsl,pins = <
-			MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x4001b8b0
-			MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31 0x4001b8b0
+			MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x4001f8b0
+			MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31 0x4001f8b0
 		>;
 	};
 
-	pinctrl_lcdif_dat: lcdif-dat-grp {
+	pinctrl_lcdif_dat: lcdifdatgrp {
 		fsl,pins = <
 			MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x00079	/* SODIMM 76 */
 			MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x00079	/* SODIMM 70 */
@@ -428,7 +565,7 @@
 		>;
 	};
 
-	pinctrl_lcdif_ctrl: lcdif-ctrl-grp {
+	pinctrl_lcdif_ctrl: lcdifctrlgrp {
 		fsl,pins = <
 			MX6UL_PAD_LCD_CLK__LCDIF_CLK	    0x00079	/* SODIMM 56 */
 			MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE  0x00079	/* SODIMM 44 */
@@ -437,31 +574,31 @@
 		>;
 	};
 
-	pinctrl_pwm4: pwm4-grp {
+	pinctrl_pwm4: pwm4grp {
 		fsl,pins = <
 			MX6UL_PAD_NAND_WP_B__PWM4_OUT	0x00079		/* SODIMM 59 */
 		>;
 	};
 
-	pinctrl_pwm5: pwm5-grp {
+	pinctrl_pwm5: pwm5grp {
 		fsl,pins = <
 			MX6UL_PAD_NAND_DQS__PWM5_OUT	0x00079		/* SODIMM 28 */
 		>;
 	};
 
-	pinctrl_pwm6: pwm6-grp {
+	pinctrl_pwm6: pwm6grp {
 		fsl,pins = <
 			MX6UL_PAD_ENET1_TX_EN__PWM6_OUT	0x00079		/* SODIMM 30 */
 		>;
 	};
 
-	pinctrl_pwm7: pwm7-grp {
+	pinctrl_pwm7: pwm7grp {
 		fsl,pins = <
 			MX6UL_PAD_ENET1_TX_CLK__PWM7_OUT	0x00079	/* SODIMM 67 */
 		>;
 	};
 
-	pinctrl_uart1: uart1-grp {
+	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX6UL_PAD_UART1_TX_DATA__UART1_DTE_RX	0x1b0b1	/* SODIMM 33 */
 			MX6UL_PAD_UART1_RX_DATA__UART1_DTE_TX	0x1b0b1	/* SODIMM 35 */
@@ -470,16 +607,16 @@
 		>;
 	};
 
-	pinctrl_uart1_ctrl1: uart1-ctrl1-grp { /* Additional DTR, DCD */
+	pinctrl_uart1_ctrl1: uart1ctrl1grp { /* Additional DTR, DCD */
 		fsl,pins = <
-			MX6UL_PAD_JTAG_TDI__GPIO1_IO13		0x70a0 /* SODIMM 31 */
-			MX6UL_PAD_LCD_DATA18__GPIO3_IO23	0x10b0 /* SODIMM 29 */
-			MX6UL_PAD_JTAG_TDO__GPIO1_IO12		0x90b1 /* SODIMM 23 */
-			MX6UL_PAD_LCD_DATA19__GPIO3_IO24        0x10b0 /* SODIMM 37 */
+			MX6UL_PAD_JTAG_TDI__GPIO1_IO13		0x70a0 /* SODIMM 31 / DCD */
+			MX6UL_PAD_LCD_DATA18__GPIO3_IO23	0x10b0 /* SODIMM 29 / DSR */
+			MX6UL_PAD_JTAG_TDO__GPIO1_IO12		0x90b1 /* SODIMM 23 / DTR */
+			MX6UL_PAD_LCD_DATA19__GPIO3_IO24        0x10b0 /* SODIMM 37 / RI */
 		>;
 	};
 
-	pinctrl_uart2: uart2-grp {
+	pinctrl_uart2: uart2grp {
 		fsl,pins = <
 			MX6UL_PAD_UART2_TX_DATA__UART2_DTE_RX	0x1b0b1 /* SODIMM 36 */
 			MX6UL_PAD_UART2_RX_DATA__UART2_DTE_TX	0x1b0b1 /* SODIMM 38 */
@@ -487,23 +624,23 @@
 			MX6UL_PAD_UART2_RTS_B__UART2_DTE_CTS	0x1b0b1 /* SODIMM 34 */
 		>;
 	};
-	pinctrl_uart5: uart5-grp {
+	pinctrl_uart5: uart5grp {
 		fsl,pins = <
 			MX6UL_PAD_GPIO1_IO04__UART5_DTE_RX	0x1b0b1 /* SODIMM 19 */
 			MX6UL_PAD_GPIO1_IO05__UART5_DTE_TX	0x1b0b1 /* SODIMM 21 */
 		>;
 	};
 
-	pinctrl_usbh_reg: gpio-usbh-reg {
+	pinctrl_usbh_reg: usbhreggrp {
 		fsl,pins = <
-			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0x10b0 /* SODIMM 129 */
+			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0x10b0 /* SODIMM 129 / USBH_PEN */
 		>;
 	};
 
-	pinctrl_usdhc1: usdhc1-grp {
+	pinctrl_usdhc1: usdhc1grp {
 		fsl,pins = <
-			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x17059 /* SODIMM 47 */
-			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x10059 /* SODIMM 190 */
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10059 /* SODIMM 47 */
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059 /* SODIMM 190 */
 			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059 /* SODIMM 192 */
 			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059 /* SODIMM 49 */
 			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059 /* SODIMM 51 */
@@ -511,10 +648,10 @@
 		>;
 	};
 
-	pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp {
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
 		fsl,pins = <
-			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x170b9
-			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x100b9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100b9
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170b9
 			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170b9
 			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170b9
 			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170b9
@@ -522,25 +659,25 @@
 		>;
 	};
 
-	pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
 		fsl,pins = <
-			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x170f9
-			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x100f9
-			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170b9
-			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170b9
-			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170b9
-			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170b9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100f9
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170f9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170f9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170f9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170f9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170f9
 		>;
 	};
 
-	pinctrl_usdhc2: usdhc2-grp {
+	pinctrl_usdhc2: usdhc2grp {
 		fsl,pins = <
 			MX6UL_PAD_CSI_DATA00__USDHC2_DATA0	0x17069
 			MX6UL_PAD_CSI_DATA01__USDHC2_DATA1	0x17069
 			MX6UL_PAD_CSI_DATA02__USDHC2_DATA2	0x17069
 			MX6UL_PAD_CSI_DATA03__USDHC2_DATA3	0x17069
 			MX6UL_PAD_CSI_HSYNC__USDHC2_CMD		0x17069
-			MX6UL_PAD_CSI_VSYNC__USDHC2_CLK		0x17069
+			MX6UL_PAD_CSI_VSYNC__USDHC2_CLK		0x10069
 
 			MX6UL_PAD_GPIO1_IO03__OSC32K_32K_OUT	0x10
 		>;
@@ -561,7 +698,7 @@
 		>;
 	};
 
-	pinctrl_wdog: wdog-grp {
+	pinctrl_wdog: wdoggrp {
 		fsl,pins = <
 			MX6UL_PAD_LCD_RESET__WDOG1_WDOG_ANY    0x30b0
 		>;
@@ -569,65 +706,65 @@
 };
 
 &iomuxc_snvs {
-	pinctrl_snvs_gpio1: snvs-gpio1-grp {
+	pinctrl_atmel_snvs_conn: atmelsnvsconngrp {
 		fsl,pins = <
-			MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06	0x110a0	/* SODIMM 93 */
-			MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x110a0	/* SODIMM 95 */
-			MX6ULL_PAD_BOOT_MODE0__GPIO5_IO10	0x1b0a0	/* SODIMM 105 */
-			MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x0b0a0	/* SODIMM 131 */
-			MX6ULL_PAD_SNVS_TAMPER8__GPIO5_IO08	0x110a0	/* SODIMM 138 */
+			MX6ULL_PAD_SNVS_TAMPER4__GPIO5_IO04     0xb0a0	/* SODIMM 107 */
 		>;
 	};
 
-	pinctrl_snvs_gpio2: snvs-gpio2-grp { /* ATMEL MXT TOUCH */
+	pinctrl_snvs_gpio1: snvsgpio1grp {
 		fsl,pins = <
-			MX6ULL_PAD_SNVS_TAMPER4__GPIO5_IO04	0xb0a0	/* SODIMM 107 */
+			MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06	0x110a0	/* SODIMM 93 */
+			MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x110a0	/* SODIMM 95 */
+			MX6ULL_PAD_BOOT_MODE0__GPIO5_IO10	0x1b0a0	/* SODIMM 105 */
+			MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x0b0a0	/* SODIMM 131 / USBH_OC */
+			MX6ULL_PAD_SNVS_TAMPER8__GPIO5_IO08	0x110a0	/* SODIMM 138 */
 		>;
 	};
 
-	pinctrl_snvs_gpio3: snvs-gpio3-grp { /* Wifi pins */
+	pinctrl_snvs_gpio3: snvsgpio3grp { /* Wifi pins */
 		fsl,pins = <
 			MX6ULL_PAD_BOOT_MODE1__GPIO5_IO11	0x130a0	/* SODIMM 127 */
 		>;
 	};
 
-	pinctrl_snvs_ad7879_int: snvs-ad7879-int-grp { /* TOUCH Interrupt */
+	pinctrl_snvs_ad7879_int: snvsad7879intgrp { /* TOUCH Interrupt */
 		fsl,pins = <
 			MX6ULL_PAD_SNVS_TAMPER7__GPIO5_IO07	0x100b0
 		>;
 	};
 
-	pinctrl_snvs_reg_sd: snvs-reg-sd-grp {
+	pinctrl_snvs_reg_sd: snvsregsdgrp {
 		fsl,pins = <
 			MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09	0x400100b0
 		>;
 	};
 
-	pinctrl_snvs_usbc_det: snvs-usbc-det-grp {
+	pinctrl_snvs_usbc_det: snvsusbcdetgrp {
 		fsl,pins = <
 			MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x130b0
 		>;
 	};
 
-	pinctrl_snvs_gpiokeys: snvs-gpiokeys-grp {
+	pinctrl_snvs_gpiokeys: snvsgpiokeysgrp {
 		fsl,pins = <
-			MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x130a0	/* SODIMM 45 */
+			MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x130a0	/* SODIMM 45 / WAKE_UP */
 		>;
 	};
 
-	pinctrl_snvs_usdhc1_cd: snvs-usdhc1-cd-grp {
+	pinctrl_snvs_usdhc1_cd: snvsusdhc1cdgrp {
 		fsl,pins = <
-			MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x1b0a0 /* SODIMM 43 */
+			MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x1b0a0 /* SODIMM 43 / MMC_CD */
 		>;
 	};
 
-	pinctrl_snvs_usdhc1_sleep_cd: snvs-usdhc1-cd-grp-slp {
+	pinctrl_snvs_usdhc1_cd_sleep: snvsusdhc1cd-sleepgrp {
 		fsl,pins = <
 			MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x0
 		>;
 	};
 
-	pinctrl_snvs_wifi_pdn: snvs-wifi-pdn-grp {
+	pinctrl_snvs_wifi_pdn: snvswifipdngrp {
 		fsl,pins = <
 			MX6ULL_PAD_BOOT_MODE1__GPIO5_IO11	0x130a0
 		>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-drc02.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-drc02.dts
new file mode 100644
index 000000000000..b539975a872c
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-drc02.dts
@@ -0,0 +1,99 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2023 DH electronics GmbH
+ *
+ * DHCOM iMX6ULL variant:
+ * DHCM-iMX6ULL-C080-R051-F0409-SPI-E2-CAN2-SD-RTC-ADC-I-01D2
+ * DHCOR PCB number: 578-200 or newer
+ * DHCOM PCB number: 579-200 or newer
+ * DRC02 PCB number: 568-100 or newer (2nd ethernet by SoM)
+ */
+/dts-v1/;
+
+#include "imx6ull-dhcom-som.dtsi"
+#include "imx6ull-dhcom-som-cfg-sdcard.dtsi"
+
+/ {
+	model = "DH electronics i.MX6ULL DHCOM on DRC02";
+	compatible = "dh,imx6ull-dhcom-drc02", "dh,imx6ull-dhcom-som",
+		     "dh,imx6ull-dhcor-som", "fsl,imx6ull";
+};
+
+/*
+ * The signals for CAN2 TX and RX are routed to the DHCOM UART1 RTS/CTS pins.
+ * Therefore the UART RTS/CTS must be output on other DHCOM pins, see uart1
+ * node below.
+ */
+&can2 {
+	status = "okay";
+};
+
+&gpio1 {
+	gpio-line-names =
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "DRC02-In2",
+		"", "", "", "",
+		"", "", "DHCOM-I", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "DRC02-HW0", "DRC02-HW1", "DHCOM-M",
+		"DRC02-HW2", "DHCOM-U", "DHCOM-T", "DHCOM-S",
+		"DHCOM-R", "DHCOM-Q", "DHCOM-P", "DHCOM-O",
+		"DHCOM-N", "", "", "";
+	/*
+	 * NOTE: On DRC02, the RS485_RX_En is controlled by a separate
+	 * GPIO line, however the i.MX6ULL UART driver assumes RX happens
+	 * during TX anyway and that it only controls drive enable DE
+	 * line. Hence, the RX is always enabled here.
+	 */
+	rs485-rx-en-hog {
+		gpio-hog;
+		gpios = <25 0>; /* GPIO Q */
+		line-name = "rs485-rx-en";
+		output-low;
+	};
+};
+
+&gpio5 {
+	gpio-line-names =
+		"DHCOM-A", "DHCOM-B", "DHCOM-C", "DRC02-Out2",
+		"DHCOM-E", "", "", "DRC02-Out1",
+		"DRC02-In1", "DHCOM-H", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+};
+
+/* DHCOM I2C2 */
+&i2c1 {
+	eeprom@56 {
+		compatible = "atmel,24c04";
+		reg = <0x56>;
+		pagesize = <16>;
+	};
+};
+
+&uart1 {
+	/delete-property/ uart-has-rtscts;
+	rts-gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>; /* GPIO I */
+	cts-gpios = <&gpio4 19 GPIO_ACTIVE_HIGH>; /* GPIO M */
+};
+
+/* Use UART as RS485 */
+&uart2 {
+	/delete-property/ uart-has-rtscts;
+	linux,rs485-enabled-at-boot-time;
+	rts-gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>; /* GPIO P */
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-pdk2.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-pdk2.dts
new file mode 100644
index 000000000000..b29713831a74
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-pdk2.dts
@@ -0,0 +1,222 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2023 DH electronics GmbH
+ *
+ * DHCOM iMX6ULL variant:
+ * DHCM-iMX6ULL-C080-R051-F0409-SPI-E2-CAN2-RTC-WBT-ADC-I-01D2
+ * DHCOR PCB number: 578-200 or newer
+ * DHCOM PCB number: 579-200 or newer
+ * PDK2 PCB number: 516-400 or newer
+ */
+/dts-v1/;
+
+#include "imx6ull-dhcom-som.dtsi"
+
+/ {
+	model = "DH electronics i.MX6ULL DHCOM on Premium Developer Kit (2)";
+	compatible = "dh,imx6ull-dhcom-pdk2", "dh,imx6ull-dhcom-som",
+		     "dh,imx6ull-dhcor-som", "fsl,imx6ull";
+
+	clk_ext_audio_codec: clock-codec {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+	};
+
+	display_bl: display-bl {
+		compatible = "pwm-backlight";
+		brightness-levels = <0 16 22 30 40 55 75 102 138 188 255>;
+		default-brightness-level = <8>;
+		enable-gpios = <&gpio5 8 GPIO_ACTIVE_HIGH>; /* GPIO G */
+		power-supply = <&reg_panel_3v3>;
+		pwms = <&pwm1 0 50000 PWM_POLARITY_INVERTED>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-0 {
+			gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; /* GPIO A */
+			label = "TA1-GPIO-A";
+			linux,code = <KEY_A>;
+			wakeup-source;
+		};
+
+		button-1 {
+			gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; /* GPIO B */
+			label = "TA2-GPIO-B";
+			linux,code = <KEY_B>;
+			wakeup-source;
+		};
+
+		button-2 {
+			gpios = <&gpio5 2 GPIO_ACTIVE_LOW>; /* GPIO C */
+			label = "TA3-GPIO-C";
+			linux,code = <KEY_C>;
+			wakeup-source;
+		};
+
+		button-3 {
+			gpios = <&gpio5 3 GPIO_ACTIVE_LOW>; /* GPIO D */
+			label = "TA4-GPIO-D";
+			linux,code = <KEY_D>;
+			wakeup-source;
+		};
+	};
+
+	led: led {
+		compatible = "gpio-leds";
+
+		/*
+		 * Disable PDK2 LED5, because GPIO E is
+		 * already used as touch interrupt.
+		 */
+		led-0 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <5>; /* PDK2 LED5 */
+			gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>; /* GPIO E */
+			status = "disabled";
+		};
+
+		led-1 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <6>; /* PDK2 LED6 */
+			gpios = <&gpio5 7 GPIO_ACTIVE_HIGH>; /* GPIO F */
+		};
+
+		/*
+		 * Disable PDK2 LED7, because GPIO H is
+		 * already used for WiFi pin WL_REG_ON.
+		 */
+		led-2 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <7>; /* PDK2 LED7 */
+			gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>; /* GPIO H */
+			status = "disabled";
+		};
+
+		/*
+		 * Disable PDK2 LED8, because GPIO I is
+		 * already used for BT pin BT_REG_ON.
+		 */
+		led-3 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <8>; /* PDK2 LED8 */
+			gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>; /* GPIO I */
+			status = "disabled";
+		};
+	};
+
+	panel {
+		compatible = "edt,etm0700g0edh6";
+		backlight = <&display_bl>;
+		power-supply = <&reg_panel_3v3>;
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
+	};
+
+	/* Filtered supply voltage */
+	reg_pdk2_24v: regulator-pdk2-24v {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <24000000>;
+		regulator-min-microvolt = <24000000>;
+		regulator-name = "24V_PDK2";
+	};
+
+	/* PDK2 U35 */
+	reg_pdk2_3v3: regulator-pdk2-3v3 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "3V3_PDK2";
+		vin-supply = <&reg_pdk2_24v>;
+	};
+
+	/* 560-200 U1 */
+	reg_panel_3v3: regulator-panel-3v3 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "3V3_PANEL";
+		vin-supply = <&reg_pdk2_24v>;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,bitclock-master = <&dailink_master>;
+		simple-audio-card,format = "i2s";
+		simple-audio-card,frame-master = <&dailink_master>;
+		simple-audio-card,name = "sgtl5000";
+		simple-audio-card,routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT";
+		simple-audio-card,widgets =
+			"Microphone", "Mic Jack",
+			"Line", "Line In Jack",
+			"Headphone", "Headphone Jack";
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai2>;
+		};
+
+		dailink_master: simple-audio-card,codec {
+			clocks = <&clk_ext_audio_codec>;
+			sound-dai = <&sgtl5000>;
+		};
+	};
+};
+
+/* DHCOM I2C1 */
+&i2c2 {
+	sgtl5000: audio-codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		clocks = <&clk_ext_audio_codec>;
+		VDDA-supply = <&reg_pdk2_3v3>;
+		VDDIO-supply = <&reg_pdk2_3v3>;
+	};
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5406";
+		reg = <0x38>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <4 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
+		power-supply = <&reg_panel_3v3>;
+	};
+};
+
+&lcdif {
+	status = "okay";
+
+	port {
+		lcd_display_out: endpoint {
+			remote-endpoint = <&lcd_panel_in>;
+		};
+	};
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&sai2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-picoitx.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-picoitx.dts
new file mode 100644
index 000000000000..e4cc2223583a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-picoitx.dts
@@ -0,0 +1,101 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2023 DH electronics GmbH
+ *
+ * DHCOM iMX6ULL variant:
+ * DHCM-iMX6ULL-C080-R051-F0409-SPI-E2-CAN2-SD-RTC-ADC-I-01D2
+ * DHCOR PCB number: 578-200 or newer
+ * DHCOM PCB number: 579-200 or newer
+ * PicoITX PCB number: 487-600 or newer
+ */
+/dts-v1/;
+
+#include "imx6ull-dhcom-som.dtsi"
+#include "imx6ull-dhcom-som-cfg-sdcard.dtsi"
+
+/ {
+	model = "DH electronics i.MX6ULL DHCOM on PicoITX";
+	compatible = "dh,imx6ull-dhcom-picoitx", "dh,imx6ull-dhcom-som",
+		     "dh,imx6ull-dhcor-som", "fsl,imx6ull";
+
+	led {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_YELLOW>;
+			default-state = "off";
+			function = LED_FUNCTION_INDICATOR;
+			gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* GPIO I */
+		};
+	};
+};
+
+&fec1 {
+	phy-handle = <&mdio1_phy0>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mdio1_phy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-id0007.c0f0", /* SMSC LAN8710Ai */
+				     "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			clock-names = "rmii-ref";
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			interrupt-parent = <&gpio5>;
+			interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+			pinctrl-0 = <&pinctrl_fec1_phy &pinctrl_snvs_fec1_phy>;
+			pinctrl-names = "default";
+			reset-assert-us = <500>;
+			reset-deassert-us = <500>;
+			reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
+			smsc,disable-energy-detect; /* Make plugin detection reliable */
+		};
+	};
+};
+
+&fec2 {
+	status = "disabled";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "PicoITX-HW2", "PicoITX-HW1", "DHCOM-M",
+		"PicoITX-HW0", "DHCOM-U", "DHCOM-T", "DHCOM-S",
+		"DHCOM-R", "DHCOM-Q", "DHCOM-P", "DHCOM-O",
+		"DHCOM-N", "", "", "";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"DHCOM-A", "DHCOM-B", "PicoITX-In2", "PicoITX-Out2",
+		"PicoITX-In1", "", "", "PicoITX-Out1",
+		"DHCOM-G", "DHCOM-H", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+};
+
+&iomuxc {
+	pinctrl_fec1: fec1-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO07__ENET1_MDC		0x1b0b0
+			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO	0x1b0b0
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN	0x1b010
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00	0x1b010
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01	0x1b010
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1	0x4001b010
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som-cfg-sdcard.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som-cfg-sdcard.dtsi
new file mode 100644
index 000000000000..5e39f8dc1351
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som-cfg-sdcard.dtsi
@@ -0,0 +1,99 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2023 DH electronics GmbH
+ */
+
+/*
+ * Special SoM configuration: SD card
+ *
+ * Enabled:  Micro SD card on module or
+ *           external SD card via DHCOM depends on hardware variant
+ *           GPIO H and GPIO I will be available
+ *           DHCOM UART2 will be available
+ * Disabled: WiFi and BT
+ */
+
+/*
+ * To use usdhc1 as SD card, the WiFi node must be deleted. The associated
+ * pwrseq node is also deleted in order to ensure that GPIO H is released.
+ * BT is also not available, so remove BT from the UART node.
+ */
+/delete-node/ &brcmf;
+/delete-node/ &usdhc1_pwrseq;
+/delete-node/ &bluetooth;
+
+/ {
+	aliases {
+		mmc1 = &usdhc1;
+		serial0 = &uart1;
+		serial1 = &uart2;
+		serial2 = &uart3;
+		serial3 = &uart4;
+		serial4 = &uart5;
+		serial5 = &uart6;
+	};
+
+	reg_sd1_vmmc: regulator-sd1-vmmc {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "VSD_3V3";
+	};
+};
+
+/* Micro SD card on module or external SD card via DHCOM */
+&usdhc1 {
+	/delete-property/ #address-cells;
+	/delete-property/ #size-cells;
+	/delete-property/ keep-power-in-suspend;
+	/delete-property/ mmc-pwrseq;
+	/delete-property/ non-removable;
+	/delete-property/ wakeup-source;
+	cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	vmmc-supply = <&reg_sd1_vmmc>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_usdhc1: usdhc1-grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10059
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x120b0 /* SD1 CD */
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170b9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100b9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170b9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170b9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170b9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170b9
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x120b0 /* SD1 CD */
+
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170f9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100f9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170f9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170f9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170f9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170f9
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x120b0 /* SD1 CD */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som.dtsi
new file mode 100644
index 000000000000..a74f5273f9b3
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som.dtsi
@@ -0,0 +1,631 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2023 DH electronics GmbH
+ */
+
+#include "imx6ull-dhcor-som.dtsi"
+
+/ {
+	aliases {
+		/delete-property/ spi2;
+		/delete-property/ spi3;
+		i2c0 = &i2c2;
+		i2c1 = &i2c1;
+		mmc2 = &usdhc2;
+		rtc0 = &rtc_i2c;
+		rtc1 = &snvs_rtc;
+		serial0 = &uart1;
+		serial1 = &uart6; /* DHCOM UART2, special hardware required */
+		serial2 = &uart3;
+		serial3 = &uart2; /* Use BT UART always as ttymxc3 */
+		serial4 = &uart4;
+		serial5 = &uart5;
+		spi0 = &ecspi1;
+		spi1 = &ecspi4; /* DHCOM SPI2, special hardware required */
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_ext_3v3_ref: regulator-ext-3v3-ref {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "VCC_3V3_REF";
+	};
+
+	reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb-otg1-vbus";
+	};
+
+	reg_usb_otg2_vbus: regulator-usb-otg2-vbus {
+		compatible = "regulator-fixed";
+		gpio = <&gpio1 5 GPIO_ACTIVE_LOW>;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb-otg2-vbus";
+	};
+
+	/* SoM with WiFi/BT: WiFi pin WL_REG_ON is connected to a DHCOM GPIO */
+	usdhc1_pwrseq: usdhc1-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>; /* GPIO H */
+	};
+};
+
+/* SoM with WiFi/BT: BT pin BT_REG_ON is connected to a DHCOM GPIO */
+&bluetooth {
+	shutdown-gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>; /* GPIO I */
+};
+
+&can1 {
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/*
+ * The signals for CAN2 TX and RX are routed to the DHCOM UART1 RTS/CTS pins.
+ * Only if this pins are used as CAN interface enable it on board layer.
+ */
+&can2 {
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	pinctrl-names = "default";
+};
+
+/* DHCOM SPI1 */
+&ecspi1 {
+	cs-gpios = <&gpio3 26 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/*
+ * DHCOM SPI2
+ * Special hardware required that uses the pins of FEC2. Therefore this SPI
+ * interface can only be used if FEC2 is disabled.
+ */
+&ecspi4 {
+	cs-gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&pinctrl_ecspi4>;
+	pinctrl-names = "default";
+};
+
+/* DHCOM ETH1 */
+&fec1 {
+	phy-handle = <&mdio2_phy0>;
+	phy-mode = "rmii";
+	pinctrl-0 = <&pinctrl_fec1>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/* DHCOM ETH2 */
+&fec2 {
+	phy-handle = <&mdio2_phy1>;
+	phy-mode = "rmii";
+	pinctrl-0 = <&pinctrl_fec2>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mdio2_phy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-id0007.c0f0", /* SMSC LAN8710Ai */
+				     "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			clock-names = "rmii-ref";
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			interrupt-parent = <&gpio5>;
+			interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+			pinctrl-0 = <&pinctrl_fec1_phy &pinctrl_snvs_fec1_phy>;
+			pinctrl-names = "default";
+			reset-assert-us = <500>;
+			reset-deassert-us = <500>;
+			reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
+			smsc,disable-energy-detect; /* Make plugin detection reliable */
+		};
+
+		mdio2_phy1: ethernet-phy@1 {
+			compatible = "ethernet-phy-id0007.c0f0", /* SMSC LAN8710Ai */
+				     "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			clock-names = "rmii-ref";
+			clocks = <&clks IMX6UL_CLK_ENET2_REF>;
+			interrupt-parent = <&gpio5>;
+			interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
+			pinctrl-0 = <&pinctrl_fec2_phy &pinctrl_snvs_fec2_phy>;
+			pinctrl-names = "default";
+			reset-assert-us = <500>;
+			reset-deassert-us = <500>;
+			reset-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
+			smsc,disable-energy-detect; /* Make plugin detection reliable */
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "DHCOM-INT",
+		"", "", "", "",
+		"", "", "DHCOM-I", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+	pinctrl-0 = <&pinctrl_spi1_switch
+		     &pinctrl_dhcom_i &pinctrl_dhcom_int>;
+	pinctrl-names = "default";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "DHCOM-L", "DHCOM-K", "DHCOM-M",
+		"DHCOM-J", "DHCOM-U", "DHCOM-T", "DHCOM-S",
+		"DHCOM-R", "DHCOM-Q", "DHCOM-P", "DHCOM-O",
+		"DHCOM-N", "", "", "";
+	pinctrl-0 = <&pinctrl_dhcom_j &pinctrl_dhcom_k
+		     &pinctrl_dhcom_l &pinctrl_dhcom_m
+		     &pinctrl_dhcom_n &pinctrl_dhcom_o
+		     &pinctrl_dhcom_p &pinctrl_dhcom_q
+		     &pinctrl_dhcom_r &pinctrl_dhcom_s
+		     &pinctrl_dhcom_t &pinctrl_dhcom_u>;
+	pinctrl-names = "default";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"DHCOM-A", "DHCOM-B", "DHCOM-C", "DHCOM-D",
+		"DHCOM-E", "", "", "DHCOM-F",
+		"DHCOM-G", "DHCOM-H", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+	pinctrl-0 = <&pinctrl_snvs_dhcom_a &pinctrl_snvs_dhcom_b
+		     &pinctrl_snvs_dhcom_c &pinctrl_snvs_dhcom_d
+		     &pinctrl_snvs_dhcom_e &pinctrl_snvs_dhcom_f
+		     &pinctrl_snvs_dhcom_g &pinctrl_snvs_dhcom_h>;
+	pinctrl-names = "default";
+};
+
+/* DHCOM I2C2 */
+&i2c1 {
+	rtc_i2c: rtc@32 {
+		compatible = "microcrystal,rv8803";
+		reg = <0x32>;
+	};
+
+	/* Microchip 24AA025E48T-I/OT containing MAC for DHCOM ETH1 */
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+
+	/* TI ADC101C027 */
+	adc@51 {
+		compatible = "ti,adc101c";
+		reg = <0x51>;
+		vref-supply = <&reg_ext_3v3_ref>;
+	};
+
+	/* TI ADC101C027 */
+	adc@52 {
+		compatible = "ti,adc101c";
+		reg = <0x52>;
+		vref-supply = <&reg_ext_3v3_ref>;
+	};
+
+	/* Microchip 24AA025E48T-I/OT containing MAC for DHCOM ETH2 */
+	eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+	};
+};
+
+/* DHCOM I2C1 */
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	pinctrl-names = "default", "gpio";
+	scl-gpios = <&gpio1 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio1 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&lcdif {
+	pinctrl-0 = <&pinctrl_lcdif>;
+	pinctrl-names = "default";
+};
+
+&pwm1 {
+	pinctrl-0 = <&pinctrl_pwm1>;
+	pinctrl-names = "default";
+};
+
+&sai2 {
+	assigned-clock-rates = <320000000>;
+	assigned-clocks = <&clks IMX6UL_CLK_PLL3_PFD2>;
+	pinctrl-0 = <&pinctrl_sai2>;
+	pinctrl-names = "default";
+};
+
+&tsc {
+	measure-delay-time = <0xffff>;
+	pinctrl-0 = <&pinctrl_tsc>;
+	pinctrl-names = "default";
+	pre-charge-time = <0xfff>;
+	touchscreen-average-samples = <32>;
+	xnur-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+};
+
+/* DHCOM UART1 */
+&uart1 {
+	pinctrl-0 = <&pinctrl_uart1>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/*
+ * DHCOM UART2 (alternative)
+ * Special hardware required that uses DHCOM GPIO pins for DHCOM UART2.
+ * Therefore this UART interface can only be used if DHCOM GPIOs J/K/L/M are
+ * removed from GPIO hog muxing.
+ */
+&uart6 {
+	pinctrl-0 = <&pinctrl_uart6>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+};
+
+&usbotg1 {
+	adp-disable;
+	disable-over-current;
+	dr_mode = "otg";
+	hnp-disable;
+	pinctrl-0 = <&pinctrl_usbotg1>;
+	pinctrl-names = "default";
+	srp-disable;
+	vbus-supply = <&reg_usb_otg1_vbus>;
+	status = "okay";
+};
+
+&usbotg2 {
+	disable-over-current; /* Overcurrent pin is used for TSC */
+	dr_mode = "host";
+	pinctrl-0 = <&pinctrl_usbotg2>;
+	pinctrl-names = "default";
+	tpl-support;
+	vbus-supply = <&reg_usb_otg2_vbus>;
+	status = "okay";
+};
+
+&usbphy1 {
+	fsl,tx-d-cal = <106>;
+};
+
+&usbphy2 {
+	fsl,tx-d-cal = <106>;
+};
+
+/* WiFi on LGA */
+&usdhc1 {
+	mmc-pwrseq = <&usdhc1_pwrseq>;
+};
+
+/* eMMC on module */
+&usdhc2 {
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-names = "default";
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_3v3>;
+	status = "okay";
+};
+
+&iomuxc {
+	/* DHCOM GPIOs I..U + INT_HIGHEST_PRIORITY */
+	pinctrl_dhcom_i: dhcom-i-grp {
+		fsl,pins = <MX6UL_PAD_UART1_CTS_B__GPIO1_IO18	0x400120b0>;
+	};
+
+	pinctrl_dhcom_j: dhcom-j-grp {
+		fsl,pins = <MX6UL_PAD_CSI_HSYNC__GPIO4_IO20	0x400120b0>;
+	};
+
+	pinctrl_dhcom_k: dhcom-k-grp {
+		fsl,pins = <MX6UL_PAD_CSI_PIXCLK__GPIO4_IO18	0x400120b0>;
+	};
+
+	pinctrl_dhcom_l: dhcom-l-grp {
+		fsl,pins = <MX6UL_PAD_CSI_MCLK__GPIO4_IO17	0x400120b0>;
+	};
+
+	pinctrl_dhcom_m: dhcom-m-grp {
+		fsl,pins = <MX6UL_PAD_CSI_VSYNC__GPIO4_IO19	0x400120b0>;
+	};
+
+	pinctrl_dhcom_n: dhcom-n-grp {
+		fsl,pins = <MX6UL_PAD_CSI_DATA07__GPIO4_IO28	0x400120b0>;
+	};
+
+	pinctrl_dhcom_o: dhcom-o-grp {
+		fsl,pins = <MX6UL_PAD_CSI_DATA06__GPIO4_IO27	0x400120b0>;
+	};
+
+	pinctrl_dhcom_p: dhcom-p-grp {
+		fsl,pins = <MX6UL_PAD_CSI_DATA05__GPIO4_IO26	0x400120b0>;
+	};
+
+	pinctrl_dhcom_q: dhcom-q-grp {
+		fsl,pins = <MX6UL_PAD_CSI_DATA04__GPIO4_IO25	0x400120b0>;
+	};
+
+	pinctrl_dhcom_r: dhcom-r-grp {
+		fsl,pins = <MX6UL_PAD_CSI_DATA03__GPIO4_IO24	0x400120b0>;
+	};
+
+	pinctrl_dhcom_s: dhcom-s-grp {
+		fsl,pins = <MX6UL_PAD_CSI_DATA02__GPIO4_IO23	0x400120b0>;
+	};
+
+	pinctrl_dhcom_t: dhcom-t-grp {
+		fsl,pins = <MX6UL_PAD_CSI_DATA01__GPIO4_IO22	0x400120b0>;
+	};
+
+	pinctrl_dhcom_u: dhcom-u-grp {
+		fsl,pins = <MX6UL_PAD_CSI_DATA00__GPIO4_IO21	0x400120b0>;
+	};
+
+	pinctrl_dhcom_int: dhcom-int-grp {
+		fsl,pins = <MX6UL_PAD_JTAG_TMS__GPIO1_IO11	0x400120b0>;
+	};
+
+	pinctrl_ecspi1: ecspi1-grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA23__ECSPI1_MISO	0x100b1
+			MX6UL_PAD_LCD_DATA22__ECSPI1_MOSI	0x100b1
+			MX6UL_PAD_LCD_DATA20__ECSPI1_SCLK	0x100b1
+			MX6UL_PAD_LCD_DATA21__GPIO3_IO26	0x1b0b0 /* SS0 */
+		>;
+	};
+
+	pinctrl_ecspi4: ecspi4-grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_TX_CLK__ECSPI4_MISO	0x100b1
+			MX6UL_PAD_ENET2_TX_EN__ECSPI4_MOSI	0x100b1
+			MX6UL_PAD_ENET2_TX_DATA1__ECSPI4_SCLK	0x100b1
+			MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15	0x1b0b0 /* SS0 */
+		>;
+	};
+
+	pinctrl_fec1: fec1-grp {
+		fsl,pins = <
+			/* FEC1 uses MDIO bus from FEC2 */
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN	0x1b010
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00	0x1b010
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01	0x1b010
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1	0x4001b010
+		>;
+	};
+
+	pinctrl_fec1_phy: fec1-phy-grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA18__GPIO3_IO23	0xb0 /* SMSC PHY reset */
+		>;
+	};
+
+	pinctrl_fec2: fec2-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO07__ENET2_MDC		0x1b0b0
+			MX6UL_PAD_GPIO1_IO06__ENET2_MDIO	0x1b0b0
+			MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN	0x1b010
+			MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00	0x1b010
+			MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01	0x1b010
+			MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	0x4001b010
+		>;
+	};
+
+	pinctrl_fec2_phy: fec2-phy-grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA19__GPIO3_IO24	0xb0 /* SMSC PHY reset */
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX	0x1b020
+			MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX	0x1b020
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX	0x1b020
+			MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX	0x1b020
+		>;
+	};
+
+	pinctrl_i2c2: i2c2-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__I2C2_SCL	0x4001b8b0
+			MX6UL_PAD_UART5_RX_DATA__I2C2_SDA	0x4001b8b0
+		>;
+	};
+
+	pinctrl_i2c2_gpio: i2c2-gpio-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30	0x4001b8b0
+			MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31	0x4001b8b0
+		>;
+	};
+
+	pinctrl_lcdif: lcdif-grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_CLK__LCDIF_CLK		0x79
+			MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE	0x79
+			MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC	0x79
+			MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC	0x79
+			MX6UL_PAD_LCD_DATA00__LCDIF_DATA00	0x79
+			MX6UL_PAD_LCD_DATA01__LCDIF_DATA01	0x79
+			MX6UL_PAD_LCD_DATA02__LCDIF_DATA02	0x79
+			MX6UL_PAD_LCD_DATA03__LCDIF_DATA03	0x79
+			MX6UL_PAD_LCD_DATA04__LCDIF_DATA04	0x79
+			MX6UL_PAD_LCD_DATA05__LCDIF_DATA05	0x79
+			MX6UL_PAD_LCD_DATA06__LCDIF_DATA06	0x79
+			MX6UL_PAD_LCD_DATA07__LCDIF_DATA07	0x79
+			MX6UL_PAD_LCD_DATA08__LCDIF_DATA08	0x79
+			MX6UL_PAD_LCD_DATA09__LCDIF_DATA09	0x79
+			MX6UL_PAD_LCD_DATA10__LCDIF_DATA10	0x79
+			MX6UL_PAD_LCD_DATA11__LCDIF_DATA11	0x79
+			MX6UL_PAD_LCD_DATA12__LCDIF_DATA12	0x79
+			MX6UL_PAD_LCD_DATA13__LCDIF_DATA13	0x79
+			MX6UL_PAD_LCD_DATA14__LCDIF_DATA14	0x79
+			MX6UL_PAD_LCD_DATA15__LCDIF_DATA15	0x79
+			MX6UL_PAD_LCD_DATA16__LCDIF_DATA16	0x79
+			MX6UL_PAD_LCD_DATA17__LCDIF_DATA17	0x79
+		>;
+	};
+
+	pinctrl_pwm1: pwm1-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO08__PWM1_OUT		0x110b0
+		>;
+	};
+
+	pinctrl_sai2: sai2-grp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA	0x130b0
+			MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK	0x17088
+			MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC	0x17088
+			MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA	0x120b0
+		>;
+	};
+
+	pinctrl_tsc: tsc-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01	0xb0
+			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0xb0
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0xb0
+			MX6UL_PAD_GPIO1_IO04__GPIO1_IO04	0xb0
+		>;
+	};
+
+	pinctrl_uart1: uart1-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart6: uart6-grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_MCLK__UART6_DCE_TX	0x1b0b1
+			MX6UL_PAD_CSI_PIXCLK__UART6_DCE_RX	0x1b0b1
+			MX6UL_PAD_CSI_VSYNC__UART6_DCE_RTS	0x1b0b1
+			MX6UL_PAD_CSI_HSYNC__UART6_DCE_CTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID	0x17059
+		>;
+	};
+
+	pinctrl_usbotg2: usbotg2-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO05__GPIO1_IO05	0x120b0
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2-grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x10069
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x17059
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x17059
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x17059
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x17059
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x17059
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x17059
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x17059
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x17059
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x17059
+			MX6UL_PAD_NAND_ALE__USDHC2_RESET_B	0x17059 /* SD2 Reset */
+		>;
+	};
+};
+
+&iomuxc_snvs {
+	/* DHCOM GPIOs A..H */
+	pinctrl_snvs_dhcom_a: snvs-dhcom-a-grp {
+		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x400120b0>;
+	};
+
+	pinctrl_snvs_dhcom_b: snvs-dhcom-b-grp {
+		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x400120b0>;
+	};
+
+	pinctrl_snvs_dhcom_c: snvs-dhcom-c-grp {
+		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x400120b0>;
+	};
+
+	pinctrl_snvs_dhcom_d: snvs-dhcom-d-grp {
+		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x400120b0>;
+	};
+
+	pinctrl_snvs_dhcom_e: snvs-dhcom-e-grp {
+		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER4__GPIO5_IO04	0x400120b0>;
+	};
+
+	pinctrl_snvs_dhcom_f: snvs-dhcom-f-grp {
+		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER7__GPIO5_IO07	0x400120b0>;
+	};
+
+	pinctrl_snvs_dhcom_g: snvs-dhcom-g-grp {
+		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER8__GPIO5_IO08	0x400120b0>;
+	};
+
+	pinctrl_snvs_dhcom_h: snvs-dhcom-h-grp {
+		fsl,pins = <MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09	0x400120b0>;
+	};
+
+	pinctrl_snvs_fec1_phy: snvs-fec1-phy-grp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05	0xb1 /* SMSC PHY Int */
+		>;
+	};
+
+	pinctrl_snvs_fec2_phy: snvs-fec2-phy-grp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06	0xb1 /* SMSC PHY Int */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-dhcor-maveo-box.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcor-maveo-box.dts
new file mode 100644
index 000000000000..047f7b2d8526
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcor-maveo-box.dts
@@ -0,0 +1,359 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (C) 2023 DH electronics GmbH
+ * Copyright (C) 2023 Marantec electronics GmbH
+ *
+ * DHCOM iMX6ULL variant:
+ * DHCR-iMX6ULL-C080-R051-SPI-WBT-I-01LG
+ * DHCOR PCB number: 578-200 or newer
+ * maveo box PCB number: 525-200 or newer
+ */
+
+/dts-v1/;
+
+#include "imx6ull-dhcor-som.dtsi"
+
+/ {
+	model = "DH electronics i.MX6ULL DHCOR on maveo box";
+	compatible = "marantec,imx6ull-dhcor-maveo-box", "dh,imx6ull-dhcor-som",
+		     "fsl,imx6ull";
+
+	aliases {
+		mmc2 = &usdhc2;
+		spi0 = &ecspi4;
+		spi3 = &ecspi1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb-otg1-vbus";
+	};
+
+	reg_usb_otg2_vbus: regulator-usb-otg2-vbus {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb-otg2-vbus";
+	};
+
+	/* WiFi pin WL_REG_ON is connected to GPIO 5.9 */
+	usdhc1_pwrseq: usdhc1-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+	};
+};
+
+/* BT pin BT_REG_ON is connected to GPIO 1.18 */
+&bluetooth {
+	shutdown-gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>;
+};
+
+/* X10 connector */
+&ecspi4 {
+	cs-gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&pinctrl_ecspi4>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	spidev@0 {
+		compatible = "dh,dhcom-board";
+		reg = <0>;
+		spi-cpha;
+		spi-cpol;
+		spi-max-frequency = <54000000>;
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"", "", "", "",
+		"", "BUTTON-USER", "", "",
+		"BUTTON-RESET", "", "", "",
+		"", "", "", "",
+		"", "", "BT-REG-ON", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"PSOC-GPIO-1", "", "", "X10-12",
+		"X10-10", "PSOC-GPIO-2", "PSOC-GPIO-3", "",
+		"X10-11", "X10-9", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"DHCOR-HW0", "DHCOR-HW1", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "MAVEO-BOX-HW0", "LED-G", "MAVEO-BOX-VAR1",
+		"MAVEO-BOX-VAR0", "MAVEO-BOX-HW1", "MAVEO-BOX-HW2", "LED-B",
+		"LED-R", "", "", "",
+		"", "", "", "";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"PSOC-SWD-IO", "PSOC-SWD-CLK", "PSOC-RESET", "ZIGBEE-PROG",
+		"ZIGBEE-RESET", "", "PSOC-PWR-FAIL-OUT", "NFC-ENABLE",
+		"NFC-IRQ", "WL-REG-ON", "DHCOR-BOOT-M0", "DHCOR-BOOT-M1",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	pinctrl-names = "default", "gpio";
+	scl-gpios = <&gpio1 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio1 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+/* Console UART */
+&uart1 {
+	pinctrl-0 = <&pinctrl_uart1>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+/* BT on LGA */
+&uart2 {
+	pinctrl-0 = <&pinctrl_uart2 &pinctrl_bt_gpio>;
+};
+
+/* Zigbee UART */
+&uart3 {
+	pinctrl-0 = <&pinctrl_uart3 &pinctrl_snvs_zigbee_gpio>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usbotg1 {
+	adp-disable;
+	disable-over-current; /* Overcurrent pin isn't connected */
+	dr_mode = "otg";
+	hnp-disable;
+	pinctrl-0 = <&pinctrl_usbotg1>;
+	pinctrl-names = "default";
+	srp-disable;
+	vbus-supply = <&reg_usb_otg1_vbus>;
+	status = "okay";
+};
+
+&usbotg2 {
+	disable-over-current; /* Overcurrent pin isn't connected */
+	dr_mode = "host";
+	pinctrl-0 = <&pinctrl_usbotg2>;
+	pinctrl-names = "default";
+	tpl-support;
+	vbus-supply = <&reg_usb_otg2_vbus>;
+	status = "okay";
+};
+
+&usbphy1 {
+	fsl,tx-d-cal = <106>;
+};
+
+&usbphy2 {
+	fsl,tx-d-cal = <106>;
+};
+
+/* WiFi on LGA */
+&usdhc1 {
+	mmc-pwrseq = <&usdhc1_pwrseq>;
+	pinctrl-0 = <&pinctrl_usdhc1_wifi &pinctrl_snvs_wifi_gpio>;
+};
+
+/* eMMC */
+&usdhc2 {
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-names = "default";
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_3v3>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-0 = <&pinctrl_hog_maveo_box>;
+	pinctrl-names = "default";
+
+	pinctrl_hog_maveo_box: hog-maveo-box-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO05__GPIO1_IO05	0x120b0    /* BUTTON_USER */
+			MX6UL_PAD_GPIO1_IO08__GPIO1_IO08	0x120b0    /* BUTTON_RESET */
+			MX6UL_PAD_CSI_PIXCLK__GPIO4_IO18	0x400120b0 /* LED_G */
+			MX6UL_PAD_CSI_DATA02__GPIO4_IO23	0x400120b0 /* LED_B */
+			MX6UL_PAD_CSI_DATA03__GPIO4_IO24	0x400120b0 /* LED_R */
+			MX6UL_PAD_ENET2_RX_DATA1__GPIO2_IO09	0x400120b0 /* X10_9 */
+			MX6UL_PAD_ENET1_TX_DATA1__GPIO2_IO04	0x400120b0 /* X10_10 */
+			MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08	0x400120b0 /* X10_11 */
+			MX6UL_PAD_ENET1_TX_DATA0__GPIO2_IO03	0x400120b0 /* X10_12 */
+			MX6UL_PAD_ENET1_RX_DATA0__GPIO2_IO00	0x400120b0 /* PSOC_GPIO_1 */
+			MX6UL_PAD_ENET1_TX_EN__GPIO2_IO05	0x400120b0 /* PSOC_GPIO_2 */
+			MX6UL_PAD_ENET1_TX_CLK__GPIO2_IO06	0x400120b0 /* PSOC_GPIO_3 */
+			MX6UL_PAD_CSI_MCLK__GPIO4_IO17		0x120b0    /* MAVEO_BOX_HW0 */
+			MX6UL_PAD_CSI_DATA00__GPIO4_IO21	0x120b0    /* MAVEO_BOX_HW1 */
+			MX6UL_PAD_CSI_DATA01__GPIO4_IO22	0x120b0    /* MAVEO_BOX_HW2 */
+			MX6UL_PAD_CSI_HSYNC__GPIO4_IO20		0x120b0    /* MAVEO_BOX_VAR0 */
+			MX6UL_PAD_CSI_VSYNC__GPIO4_IO19		0x120b0    /* MAVEO_BOX_VAR1 */
+			MX6UL_PAD_LCD_CLK__GPIO3_IO00		0x120b0    /* DHCOR_HW0 */
+			MX6UL_PAD_LCD_ENABLE__GPIO3_IO01	0x120b0    /* DHCOR_HW1 */
+			MX6UL_PAD_LCD_DATA00__GPIO3_IO05	0x120b0
+			MX6UL_PAD_LCD_DATA01__GPIO3_IO06	0x120b0
+			MX6UL_PAD_LCD_DATA02__GPIO3_IO07	0x120b0
+			MX6UL_PAD_LCD_DATA03__GPIO3_IO08	0x120b0
+			MX6UL_PAD_LCD_DATA04__GPIO3_IO09	0x120b0
+			MX6UL_PAD_LCD_DATA05__GPIO3_IO10	0x120b0
+			MX6UL_PAD_LCD_DATA06__GPIO3_IO11	0x120b0
+			MX6UL_PAD_LCD_DATA07__GPIO3_IO12	0x120b0
+			MX6UL_PAD_LCD_DATA08__GPIO3_IO13	0x120b0
+			MX6UL_PAD_LCD_DATA09__GPIO3_IO14	0x120b0
+			MX6UL_PAD_LCD_DATA10__GPIO3_IO15	0x120b0
+			MX6UL_PAD_LCD_DATA11__GPIO3_IO16	0x120b0
+			MX6UL_PAD_LCD_DATA12__GPIO3_IO17	0x120b0
+			MX6UL_PAD_LCD_DATA13__GPIO3_IO18	0x120b0
+			MX6UL_PAD_LCD_DATA14__GPIO3_IO19	0x120b0
+			MX6UL_PAD_LCD_DATA15__GPIO3_IO20	0x120b0
+			MX6UL_PAD_LCD_DATA16__GPIO3_IO21	0x120b0
+			MX6UL_PAD_LCD_DATA17__GPIO3_IO22	0x120b0
+			MX6UL_PAD_LCD_DATA18__GPIO3_IO23	0x120b0
+		>;
+	};
+
+	pinctrl_bt_gpio: bt-gpio-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18	0x400120b0 /* BT_REG_ON */
+		>;
+	};
+
+	pinctrl_ecspi4: ecspi4-grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_TX_CLK__ECSPI4_MISO	0x100b1
+			MX6UL_PAD_ENET2_TX_EN__ECSPI4_MOSI	0x100b1
+			MX6UL_PAD_ENET2_TX_DATA1__ECSPI4_SCLK	0x100b1
+			MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15	0x1b0b0 /* SS0 */
+		>;
+	};
+
+	pinctrl_i2c2: i2c2-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__I2C2_SCL	0x4001b8b0
+			MX6UL_PAD_UART5_RX_DATA__I2C2_SDA	0x4001b8b0
+		>;
+	};
+
+	pinctrl_i2c2_gpio: i2c2-gpio-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30	0x4001b8b0
+			MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31	0x4001b8b0
+		>;
+	};
+
+	pinctrl_uart1: uart1-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart3: uart3-grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_READY_B__UART3_DCE_TX	0x1b0b1
+			MX6UL_PAD_NAND_CE0_B__UART3_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID	0x17059
+			MX6UL_PAD_GPIO1_IO04__GPIO1_IO04	0x120b0 /* USB_OTG1_PWR */
+		>;
+	};
+
+	pinctrl_usbotg2: usbotg2-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0x120b0 /* USB_OTG2_PWR */
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2-grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x10069
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x17059
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x17059
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x17059
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x17059
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x17059
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x17059
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x17059
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x17059
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x17059
+			MX6UL_PAD_NAND_ALE__USDHC2_RESET_B	0x17059 /* SD2 Reset */
+		>;
+	};
+};
+
+&iomuxc_snvs {
+	pinctrl-0 = <&pinctrl_snvs_hog_maveo_box>;
+	pinctrl-names = "default";
+
+	pinctrl_snvs_hog_maveo_box: snvs-hog-maveo-box-grp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x400120b0 /* PSOC_SWD_IO */
+			MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x400120b0 /* PSOC_SWD_CLK */
+			MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x400120b0 /* PSOC_RESET */
+			MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06	0x400120b0 /* PSOC_PWR_FAIL_OUT */
+			MX6ULL_PAD_SNVS_TAMPER7__GPIO5_IO07	0x400120b0 /* NFC_ENABLE */
+			MX6ULL_PAD_SNVS_TAMPER8__GPIO5_IO08	0x400120b0 /* NFC_IRQ */
+			MX6ULL_PAD_BOOT_MODE0__GPIO5_IO10	0x120b0    /* DHCOR_BOOT_M0 */
+			MX6ULL_PAD_BOOT_MODE1__GPIO5_IO11	0x120b0    /* DHCOR_BOOT_M1 */
+		>;
+	};
+
+	pinctrl_snvs_wifi_gpio: snvs-wifi-gpio-grp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09	0x400120b0 /* WL_REG_ON */
+		>;
+	};
+
+	pinctrl_snvs_zigbee_gpio: snvs-zigbee-gpio-grp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x400120b0 /* ZIGBEE_PROG */
+			MX6ULL_PAD_SNVS_TAMPER4__GPIO5_IO04	0x400120b0 /* ZIGBEE_RESET */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-dhcor-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcor-som.dtsi
new file mode 100644
index 000000000000..75486e1b0c15
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcor-som.dtsi
@@ -0,0 +1,270 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2023 DH electronics GmbH
+ */
+
+#include <dt-bindings/clock/imx6ul-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/regulator/dlg,da9063-regulator.h>
+#include "imx6ull.dtsi"
+
+/ {
+	aliases {
+		/delete-property/ mmc0;
+		/delete-property/ mmc1;
+	};
+
+	memory@80000000 {
+		/* Appropriate memory size will be filled by U-Boot */
+		reg = <0x80000000 0>;
+		device_type = "memory";
+	};
+};
+
+&cpu0 {
+	/*
+	 * Due to the design as a solderable SOM, there are no capacitors
+	 * below the SoC, therefore higher voltages are required.
+	 * Due to CPU lifetime consideration of the SoC manufacturer and
+	 * the preferred area of operation in the industrial related
+	 * environment, set the maximum frequency for each DHCOM i.MX6ULL
+	 * to 792MHz, as with the industrial type.
+	 */
+	clock-frequency = <792000000>;
+	operating-points = <
+		/* kHz	uV */
+		792000	1250000 /* Voltage increased */
+		528000	1175000
+		396000	1025000
+		198000	950000
+	>;
+	fsl,soc-operating-points = <
+		/* KHz	uV */
+		792000	1250000 /* Voltage increased */
+		528000	1175000
+		396000	1175000
+		198000	1175000
+	>;
+};
+
+&gpio1 {
+	pinctrl-0 = <&pinctrl_spi1_switch>;
+	pinctrl-names = "default";
+	/*
+	 * Pin SPI_BOOT_FLASH_EN (GPIO 1.9) is a switch for either using the
+	 * DHCOM SPI1 interface or accessing the SPI bootflash. Both using
+	 * ecspi1, but muxed to different pins. The DHCOM SPI1 interface uses
+	 * the pins PAD_LCD_DATA21..23 and the SPI bootflash uses the pins
+	 * PAD_CSI_DATA04..07. If the SPI bootflash is enabled the pins for
+	 * DHCOM GPIOs N/O/P/Q/R/S/T/U aren't usable anymore, because they
+	 * are used for the bus interface to the SPI bootflash. The GPIOs are
+	 * disconnected by a buffer which is also controlled via the pin
+	 * SPI_BOOT_FLASH_EN. Therefore the access to the bootflash is a
+	 * special case and is disabled by setting GPIO 1.9 to high.
+	 */
+	spi1-switch-hog {
+		gpio-hog;
+		gpios = <9 0>;
+		output-high;
+		line-name = "spi1-switch";
+	};
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	pinctrl-names = "default", "gpio";
+	scl-gpios = <&gpio1 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio1 29 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	pmic@58 {
+		compatible = "dlg,da9061";
+		reg = <0x58>;
+
+		onkey {
+			compatible = "dlg,da9061-onkey", "dlg,da9062-onkey";
+			status = "disabled";
+		};
+
+		regulators {
+			vdd_soc_in_1v4: buck1 {
+				regulator-allowed-modes = <DA9063_BUCK_MODE_SLEEP>; /* PFM */
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <DA9063_BUCK_MODE_SLEEP>;
+				regulator-max-microvolt = <1400000>;
+				regulator-min-microvolt = <1400000>;
+				regulator-name = "vdd_soc_in_1v4";
+			};
+
+			vcc_3v3: buck2 {
+				regulator-allowed-modes = <DA9063_BUCK_MODE_SYNC>; /* PWM */
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <DA9063_BUCK_MODE_SYNC>;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-name = "vcc_3v3";
+			};
+
+			/*
+			 * The current DRR3 memory can be supplied with a
+			 * voltage of either 1.35V or 1.5V. For reasons of
+			 * backward compatibility to only 1.5V DDR3 memory,
+			 * the voltage is set to 1.5V.
+			 */
+			vcc_ddr_1v35: buck3 {
+				regulator-allowed-modes = <DA9063_BUCK_MODE_SYNC>; /* PWM */
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <DA9063_BUCK_MODE_SYNC>;
+				regulator-max-microvolt = <1500000>;
+				regulator-min-microvolt = <1500000>;
+				regulator-name = "vcc_ddr_1v35";
+			};
+
+			vcc_2v5: ldo1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <2500000>;
+				regulator-min-microvolt = <2500000>;
+				regulator-name = "vcc_2v5";
+			};
+
+			vdd_snvs_in_3v3: ldo2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-name = "vdd_snvs_in_3v3";
+			};
+
+			vcc_1v8: ldo3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "vcc_1v8";
+			};
+
+			vcc_1v2: ldo4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1200000>;
+				regulator-min-microvolt = <1200000>;
+				regulator-name = "vcc_1v2";
+			};
+		};
+
+		thermal {
+			compatible = "dlg,da9061-thermal", "dlg,da9062-thermal";
+			status = "disabled";
+		};
+
+		watchdog {
+			compatible = "dlg,da9061-watchdog", "dlg,da9062-watchdog";
+			status = "disabled";
+		};
+	};
+};
+
+&ocotp {
+	/* Don't get write access by default */
+	read-only;
+};
+
+&reg_arm {
+	vin-supply = <&vdd_soc_in_1v4>;
+};
+
+&reg_soc {
+	vin-supply = <&vdd_soc_in_1v4>;
+};
+
+/* BT on LGA (BT_REG_ON is connected to LGA pin E1) */
+&uart2 {
+	pinctrl-0 = <&pinctrl_uart2>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+	status = "okay";
+
+	/*
+	 * Actually, the maximum speed of the chip is 4MBdps, but there are
+	 * limitations that prevent this speed. It hasn't yet been figured out
+	 * what the reason for this is. Currently, the maximum speed of 3MBdps
+	 * can be used without any problems. If the limitation can be overcome,
+	 * the speed can be increased accordingly.
+	 */
+	bluetooth: bluetooth {
+		compatible = "brcm,bcm43430a1-bt"; /* muRata 1DX */
+		max-speed = <3000000>;
+		vbat-supply = <&vcc_3v3>;
+		vddio-supply = <&vcc_3v3>;
+	};
+};
+
+/* WiFi on LGA (WL_REG_ON is connected to LGA pin E3) */
+&usdhc1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	bus-width = <4>;
+	no-1-8-v;
+	non-removable;
+	keep-power-in-suspend;
+	pinctrl-0 = <&pinctrl_usdhc1_wifi>;
+	pinctrl-names = "default";
+	wakeup-source;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		compatible = "brcm,bcm43430a1-fmac", "brcm,bcm4329-fmac"; /* muRata 1DX */
+		reg = <1>;
+	};
+};
+
+&iomuxc {
+	pinctrl_i2c1: i2c1-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_TX_DATA__I2C1_SCL	0x4001b8b0
+			MX6UL_PAD_UART4_RX_DATA__I2C1_SDA	0x4001b8b0
+		>;
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28	0x4001b8b0
+			MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29	0x4001b8b0
+		>;
+	};
+
+	pinctrl_spi1_switch: spi1-switch-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO09__GPIO1_IO09	0x120b0 /* SPI_BOOT_FLASH_EN */
+		>;
+	};
+
+	pinctrl_uart2: uart2-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX	0x1b0b1
+			MX6UL_PAD_UART3_RX_DATA__UART2_DCE_RTS	0x1b0b1
+			MX6UL_PAD_UART3_TX_DATA__UART2_DCE_CTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc1_wifi: usdhc1-wifi-grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x1b0b0
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10010
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x1b0b0
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x1b0b0
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x1b0b0
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-engicam-microgea-bmm.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-engicam-microgea-bmm.dts
new file mode 100644
index 000000000000..279d46c22cd7
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-engicam-microgea-bmm.dts
@@ -0,0 +1,303 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2025 Amarula Solutions, Dario Binacchi <dario.binacchi@amarulasolutions.com>
+ * Copyright (C) 2025 Engicam srl
+ */
+
+/dts-v1/;
+
+#include "imx6ull-engicam-microgea.dtsi"
+
+/ {
+	compatible = "engicam,microgea-imx6ull-bmm",
+		     "engicam,microgea-imx6ull", "fsl,imx6ull";
+	model = "Engicam MicroGEA i.MX6ULL BMM Board";
+
+	backlight {
+		compatible = "pwm-backlight";
+		brightness-levels = <0 100>;
+		num-interpolated-steps = <100>;
+		default-brightness-level = <85>;
+		pwms = <&pwm8 0 100000 0>;
+	};
+
+	buzzer {
+		compatible = "pwm-beeper";
+		pwms = <&pwm4 0 1000000 0>;
+	};
+
+	reg_1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_usb1_vbus: regulator-usb1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usb1>;
+		regulator-name = "usb1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio5 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usb2_vbus: regulator-usb2-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usb2>;
+		regulator-name = "usbotg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio5 3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_ext_pwr: regulator-ext-pwr {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_ext_pwr>;
+		regulator-name = "ext-pwr";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio5 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "imx6ull-microgea-bmm-sgtl5000";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&codec_dai>;
+		simple-audio-card,frame-master = <&codec_dai>;
+		simple-audio-card,widgets =
+			"Microphone", "Mic Jack",
+			"Headphone", "Headphone Jack";
+		simple-audio-card,routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"Headphone Jack", "HP_OUT";
+
+		cpu_dai: simple-audio-card,cpu {
+			sound-dai = <&sai2>;
+		};
+
+		codec_dai: simple-audio-card,codec {
+			sound-dai = <&codec>;
+		};
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	codec: audio-codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_mclk>;
+		#sound-dai-cells = <0>;
+		clocks = <&clks IMX6UL_CLK_CKO>;
+		assigned-clocks = <&clks IMX6UL_CLK_CKO2_SEL>,
+				  <&clks IMX6UL_CLK_CKO2_PODF>,
+				  <&clks IMX6UL_CLK_CKO2>,
+				  <&clks IMX6UL_CLK_CKO>;
+		assigned-clock-parents = <&clks IMX6UL_CLK_OSC>,
+					 <&clks IMX6UL_CLK_CKO2_SEL>,
+					 <&clks IMX6UL_CLK_CKO2_PODF>,
+					 <&clks IMX6UL_CLK_CKO2>;
+		VDDA-supply = <&reg_3v3>;
+		VDDIO-supply = <&reg_3v3>;
+		VDDD-supply = <&reg_1v8>;
+	};
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+	status = "okay";
+};
+
+&pwm8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm8>;
+	status = "okay";
+};
+
+&sai2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai2>;
+	status = "okay";
+};
+
+&tsc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_tsc>;
+	measure-delay-time = <0x9ffff>;
+	pre-charge-time = <0xfff>;
+	xnur-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&usbotg1 {
+	dr_mode = "host";
+	vbus-supply = <&reg_usb1_vbus>;
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	vbus-supply = <&reg_usb2_vbus>;
+	status = "okay";
+};
+
+/* MicroSD */
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	vmmc-supply = <&reg_3v3>;
+	bus-width = <4>;
+	keep-power-in-suspend;
+	non-removable;
+	wakeup-source;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_can: can-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX	0x1b020
+			MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX	0x1b020
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__I2C2_SCL		0x4001b8b0
+			MX6UL_PAD_UART5_RX_DATA__I2C2_SDA	0x4001b8b0
+		>;
+	};
+
+	pinctrl_mclk: mclkgrp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TMS__CCM_CLKO1		0x13009
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO05__PWM4_OUT		0x110b0
+		>;
+	};
+
+	pinctrl_pwm8: pwm8grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_ER__PWM8_OUT		0x11008
+		>;
+	};
+
+	pinctrl_sai2: sai2grp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA	0x130b0
+			MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK	0x17088
+			MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC	0x17088
+			MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA	0x120b0
+		>;
+	};
+
+	pinctrl_tsc: tscgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01	0x000b0
+			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0x000b0
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0x000b0
+			MX6UL_PAD_GPIO1_IO04__GPIO1_IO04	0x000b0
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10059
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170b9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100b9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170b9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170b9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170b9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170f9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100f9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170f9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170f9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170f9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170f9
+		>;
+	};
+};
+
+&iomuxc_snvs {
+	pinctrl_reg_usb1: regusb1grp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x17059
+		>;
+	};
+
+	pinctrl_reg_usb2: regusb2grp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x17059
+		>;
+	};
+
+	pinctrl_reg_ext_pwr: reg-ext-pwrgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06	0x17059
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-engicam-microgea-gtw.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-engicam-microgea-gtw.dts
new file mode 100644
index 000000000000..d500f8839102
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-engicam-microgea-gtw.dts
@@ -0,0 +1,162 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2025 Amarula Solutions, Dario Binacchi <dario.binacchi@amarulasolutions.com>
+ * Copyright (C) 2025 Engicam srl
+ */
+
+/dts-v1/;
+
+#include "imx6ull-engicam-microgea.dtsi"
+
+/ {
+	compatible = "engicam,microgea-imx6ull-gtw",
+		     "engicam,microgea-imx6ull", "fsl,imx6ull";
+	model = "Engicam MicroGEA i.MX6ULL GTW Board";
+
+	reg_1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		user-button {
+			label = "User button";
+			gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_MISC>;
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>, <&pinctrl_pwrled>;
+
+		led-0 {
+			gpios = <&gpio5 7 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		led-1 {
+			gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-2 {
+			gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-3 {
+			gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	usb_hub: usb-hub {
+		compatible = "smsc,usb3503a";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb_hub>;
+		reset-gpios = <&gpio5 6 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&usbotg1 {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+/* MicroSD */
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	vmmc-supply = <&reg_3v3>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_gpio_keys: gpio_keysgrp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TDI__GPIO1_IO13		0x0b0b0
+		>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TCK__GPIO1_IO14		0x130b0
+			MX6UL_PAD_JTAG_TRST_B__GPIO1_IO15	0x130b0
+			MX6UL_PAD_JTAG_TDO__GPIO1_IO12		0x130b0
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX	0x1b0b1
+			MX6UL_PAD_UART2_RTS_B__UART2_DCE_RTS	0x1b0b1
+			MX6UL_PAD_UART2_CTS_B__UART2_DCE_CTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10059
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
+		>;
+	};
+};
+
+&iomuxc_snvs {
+	pinctrl_pwrled: ledsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER7__GPIO5_IO07	0x130b0
+		>;
+	};
+
+	pinctrl_usb_hub: usb_hubgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06	0x17059
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-engicam-microgea-rmm.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-engicam-microgea-rmm.dts
new file mode 100644
index 000000000000..107b00b9a939
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-engicam-microgea-rmm.dts
@@ -0,0 +1,360 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2025 Amarula Solutions, Dario Binacchi <dario.binacchi@amarulasolutions.com>
+ * Copyright (C) 2025 Engicam srl
+ */
+
+/dts-v1/;
+
+#include "imx6ull-engicam-microgea.dtsi"
+
+/ {
+	compatible = "engicam,microgea-imx6ull-rmm",
+		     "engicam,microgea-imx6ull", "fsl,imx6ull";
+	model = "Engicam MicroGEA i.MX6ULL BMM Board";
+
+	backlight {
+		compatible = "pwm-backlight";
+		brightness-levels = <0 100>;
+		num-interpolated-steps = <100>;
+		default-brightness-level = <85>;
+		pwms = <&pwm8 0 100000 0>;
+	};
+
+	buzzer {
+		compatible = "pwm-beeper";
+		pwms = <&pwm4 0 1000000 0>;
+	};
+
+	reg_1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_usb1_vbus: regulator-usb1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usb1>;
+		regulator-name = "usb1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio5 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usb2_vbus: regulator-usb2-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usb2>;
+		regulator-name = "usbotg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio5 3 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_ext_pwr: regulator-ext-pwr {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_ext_pwr>;
+		regulator-name = "ext-pwr";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio5 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "imx6ull-microgea-rmm-sgtl5000";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&codec_dai>;
+		simple-audio-card,frame-master = <&codec_dai>;
+		simple-audio-card,widgets =
+			"Microphone", "Mic Jack",
+			"Headphone", "Headphone Jack";
+		simple-audio-card,routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"Headphone Jack", "HP_OUT";
+
+		cpu_dai: simple-audio-card,cpu {
+			sound-dai = <&sai2>;
+		};
+
+		codec_dai: simple-audio-card,codec {
+			sound-dai = <&codec>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+
+		led-0 {
+			gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+			status = "okay";
+		};
+
+		led-1 {
+			gpios = <&gpio2 11 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+			status = "okay";
+		};
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	touchscreen: touchscreen@38 {
+		compatible = "edt,edt-ft5306";
+		reg = <0x38>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touchscreen>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
+		report-rate-hz = <6>;
+		/* settings valid only for Hycon touchscreen */
+		touchscreen-size-x = <1280>;
+		touchscreen-size-y = <800>;
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	codec: audio-codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_mclk>;
+		#sound-dai-cells = <0>;
+		clocks = <&clks IMX6UL_CLK_CKO>;
+		assigned-clocks = <&clks IMX6UL_CLK_CKO2_SEL>,
+				  <&clks IMX6UL_CLK_CKO2_PODF>,
+				  <&clks IMX6UL_CLK_CKO2>,
+				  <&clks IMX6UL_CLK_CKO>;
+		assigned-clock-parents = <&clks IMX6UL_CLK_OSC>,
+					 <&clks IMX6UL_CLK_CKO2_SEL>,
+					 <&clks IMX6UL_CLK_CKO2_PODF>,
+					 <&clks IMX6UL_CLK_CKO2>;
+		VDDA-supply = <&reg_3v3>;
+		VDDIO-supply = <&reg_3v3>;
+		VDDD-supply = <&reg_1v8>;
+	};
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+	status = "okay";
+};
+
+&pwm8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm8>;
+	status = "okay";
+};
+
+&sai2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai2>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usbotg1 {
+	dr_mode = "host";
+	vbus-supply = <&reg_usb1_vbus>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	vbus-supply = <&reg_usb2_vbus>;
+	disable-over-current;
+	status = "okay";
+};
+
+/* MicroSD */
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	vmmc-supply = <&reg_3v3>;
+	bus-width = <4>;
+	keep-power-in-suspend;
+	non-removable;
+	wakeup-source;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_can: can-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX	0x1b020
+			MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX	0x1b020
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_PIXCLK__I2C1_SCL		0x4001b8b0
+			MX6UL_PAD_CSI_MCLK__I2C1_SDA		0x4001b8b0
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__I2C2_SCL		0x4001b8b0
+			MX6UL_PAD_GPIO1_IO01__I2C2_SDA		0x4001b8b0
+		>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10	0x130b0
+			MX6UL_PAD_ENET2_TX_DATA0__GPIO2_IO11	0x130b0
+		>;
+	};
+
+	pinctrl_mclk: mclkgrp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TMS__CCM_CLKO1		0x13009
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO05__PWM4_OUT		0x110b0
+		>;
+	};
+
+	pinctrl_pwm8: pwm8grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_ER__PWM8_OUT		0x110b0
+		>;
+	};
+
+	pinctrl_sai2: sai2grp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA	0x130b0
+			MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK	0x17088
+			MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC	0x17088
+			MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA	0x120b0
+		>;
+	};
+
+	pinctrl_touchscreen: touchgrp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_TX_CLK__GPIO2_IO14	0x17059
+			MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08	0x17059
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_TX_DATA__UART4_DCE_TX	0x0b0b0
+			MX6UL_PAD_UART4_RX_DATA__UART4_DCE_RX	0x0b0b0
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10059
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170b9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100b9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170b9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170b9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170b9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170f9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100f9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170f9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170f9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170f9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170f9
+		>;
+	};
+};
+
+&iomuxc_snvs {
+	pinctrl_reg_usb1: regusb1grp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x17059
+		>;
+	};
+
+	pinctrl_reg_usb2: regusb2grp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x17059
+		>;
+	};
+
+	pinctrl_reg_ext_pwr: reg-ext-pwrgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06	0x17059
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-engicam-microgea.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-engicam-microgea.dtsi
new file mode 100644
index 000000000000..43518bf07602
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-engicam-microgea.dtsi
@@ -0,0 +1,95 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2025 Amarula Solutions, Dario Binacchi <dario.binacchi@amarulasolutions.com>
+ * Copyright (C) 2025 Engicam srl
+ */
+
+/dts-v1/;
+
+ #include "imx6ull.dtsi"
+
+/ {
+	compatible = "engicam,microgea-imx6ull", "fsl,imx6ull";
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>, <&pinctrl_phy_reset>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy0>;
+	local-mac-address = [00 00 00 00 00 00];
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <4000>;
+			reset-deassert-us = <4000>;
+		};
+	};
+};
+
+/* NAND */
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	nand-ecc-mode = "hw";
+	nand-ecc-strength = <0>;
+	nand-ecc-step-size = <0>;
+	nand-on-flash-bbt;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1	0x4001b009
+			MX6UL_PAD_GPIO1_IO07__ENET1_MDC		0x1b0b0
+			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO	0x1b0b0
+		>;
+	};
+
+	pinctrl_gpmi_nand: gpminandgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_CLE__RAWNAND_CLE		0xb0b1
+			MX6UL_PAD_NAND_ALE__RAWNAND_ALE		0xb0b1
+			MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B	0xb0b1
+			MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B	0xb000
+			MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B	0xb0b1
+			MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B	0xb0b1
+			MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B	0xb0b1
+			MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00	0xb0b1
+			MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01	0xb0b1
+			MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02	0xb0b1
+			MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03	0xb0b1
+			MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04	0xb0b1
+			MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05	0xb0b1
+			MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06	0xb0b1
+			MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07	0xb0b1
+		>;
+	};
+};
+
+&iomuxc_snvs {
+	pinctrl_phy_reset: phy-resetgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09	0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ull-jozacp.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-jozacp.dts
index a152eeb78e88..a152eeb78e88 100644
--- a/arch/arm/boot/dts/imx6ull-jozacp.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-jozacp.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-kontron-bl.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-kontron-bl.dts
new file mode 100644
index 000000000000..fa016465cdbc
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-kontron-bl.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2019 Kontron Electronics GmbH
+ */
+
+/dts-v1/;
+
+#include "imx6ull-kontron-sl.dtsi"
+#include "imx6ul-kontron-bl-common.dtsi"
+
+/ {
+	model = "Kontron BL i.MX6ULL (N641X S)";
+	compatible = "kontron,bl-imx6ull", "kontron,sl-imx6ull", "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-kontron-sl.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-kontron-sl.dtsi
new file mode 100644
index 000000000000..93f10eb3494f
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-kontron-sl.dtsi
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ */
+
+#include "imx6ull.dtsi"
+#include "imx6ul-kontron-sl-common.dtsi"
+
+/ {
+	model = "Kontron SL i.MX6ULL (N641X SOM)";
+	compatible = "kontron,sl-imx6ull", "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/imx6ull-myir-mys-6ulx-eval.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-myir-mys-6ulx-eval.dts
index 79cc45728cd2..79cc45728cd2 100644
--- a/arch/arm/boot/dts/imx6ull-myir-mys-6ulx-eval.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-myir-mys-6ulx-eval.dts
diff --git a/arch/arm/boot/dts/imx6ull-myir-mys-6ulx.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-myir-mys-6ulx.dtsi
index d03694feaf5c..83b9de17cee2 100644
--- a/arch/arm/boot/dts/imx6ull-myir-mys-6ulx.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-myir-mys-6ulx.dtsi
@@ -169,7 +169,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+	pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp {
 		fsl,pins = <
 			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170b9
 			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100b9
@@ -180,7 +180,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+	pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
 		fsl,pins = <
 			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170f9
 			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100f9
@@ -206,7 +206,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+	pinctrl_usdhc2_100mhz: usdhc2-100mhz-grp {
 		fsl,pins = <
 			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x100b9
 			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x170b9
@@ -221,7 +221,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+	pinctrl_usdhc2_200mhz: usdhc2-200mhz-grp {
 		fsl,pins = <
 			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x100f9
 			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x170f9
diff --git a/arch/arm/boot/dts/imx6ull-opos6ul.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-opos6ul.dtsi
index 155f941f2811..155f941f2811 100644
--- a/arch/arm/boot/dts/imx6ull-opos6ul.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-opos6ul.dtsi
diff --git a/arch/arm/boot/dts/imx6ull-opos6uldev.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-opos6uldev.dts
index 198fdb72641b..198fdb72641b 100644
--- a/arch/arm/boot/dts/imx6ull-opos6uldev.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-opos6uldev.dts
diff --git a/arch/arm/boot/dts/imx6ull-phytec-phycore-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-phycore-som.dtsi
index 56cd16e5a77f..56cd16e5a77f 100644
--- a/arch/arm/boot/dts/imx6ull-phytec-phycore-som.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-phycore-som.dtsi
diff --git a/arch/arm/boot/dts/imx6ull-phytec-segin-ff-rdk-emmc.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin-ff-rdk-emmc.dts
index 8e2a4c5d7765..8e2a4c5d7765 100644
--- a/arch/arm/boot/dts/imx6ull-phytec-segin-ff-rdk-emmc.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin-ff-rdk-emmc.dts
diff --git a/arch/arm/boot/dts/imx6ull-phytec-segin-ff-rdk-nand.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin-ff-rdk-nand.dts
index 1d7362b5ac91..1d7362b5ac91 100644
--- a/arch/arm/boot/dts/imx6ull-phytec-segin-ff-rdk-nand.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin-ff-rdk-nand.dts
diff --git a/arch/arm/boot/dts/imx6ull-phytec-segin-lc-rdk-nand.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin-lc-rdk-nand.dts
index 4bcbae024d8d..4bcbae024d8d 100644
--- a/arch/arm/boot/dts/imx6ull-phytec-segin-lc-rdk-nand.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin-lc-rdk-nand.dts
diff --git a/arch/arm/boot/dts/imx6ull-phytec-segin-peb-av-02.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin-peb-av-02.dtsi
index 06bb7f327780..06bb7f327780 100644
--- a/arch/arm/boot/dts/imx6ull-phytec-segin-peb-av-02.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin-peb-av-02.dtsi
diff --git a/arch/arm/boot/dts/imx6ull-phytec-segin-peb-eval-01.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin-peb-eval-01.dtsi
index ff08d95a1aa2..ff08d95a1aa2 100644
--- a/arch/arm/boot/dts/imx6ull-phytec-segin-peb-eval-01.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin-peb-eval-01.dtsi
diff --git a/arch/arm/boot/dts/imx6ull-phytec-segin-peb-wlbt-05.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin-peb-wlbt-05.dtsi
index df25814a3371..df25814a3371 100644
--- a/arch/arm/boot/dts/imx6ull-phytec-segin-peb-wlbt-05.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin-peb-wlbt-05.dtsi
diff --git a/arch/arm/boot/dts/imx6ull-phytec-segin.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin.dtsi
index e287a0453b5f..e287a0453b5f 100644
--- a/arch/arm/boot/dts/imx6ull-phytec-segin.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-segin.dtsi
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-tauri-emmc.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-tauri-emmc.dts
new file mode 100644
index 000000000000..1610f3892d9e
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-tauri-emmc.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2021 PHYTEC Messtechnik GmbH
+ * Author: Alexander Bauer <a.bauer@phytec.de>
+ */
+
+/dts-v1/;
+#include "imx6ull-phytec-tauri.dtsi"
+
+/ {
+	model = "PHYTEC phyGate-Tauri i.MX6 UltraLite";
+	compatible = "phytec,imx6ull-phygate-tauri-emmc",
+		     "phytec,imx6ull-phygate-tauri",
+		     "phytec,imx6ull-pcl063", "fsl,imx6ull";
+};
+
+/* EMMC-Version */
+&usdhc2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-tauri-nand.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-tauri-nand.dts
new file mode 100644
index 000000000000..92e7d38d5637
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-tauri-nand.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2021 PHYTEC Messtechnik GmbH
+ * Author: Alexander Bauer <a.bauer@phytec.de>
+ */
+
+/dts-v1/;
+#include "imx6ull-phytec-tauri.dtsi"
+
+/ {
+	model = "PHYTEC phyGate-Tauri i.MX6 UltraLite";
+	compatible = "phytec,imx6ull-phygate-tauri-nand",
+		     "phytec,imx6ull-phygate-tauri",
+		     "phytec,imx6ull-pcl063", "fsl,imx6ull";
+};
+
+/* NAND-Version */
+&gpmi {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-tauri.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-tauri.dtsi
new file mode 100644
index 000000000000..7ee25b141627
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-phytec-tauri.dtsi
@@ -0,0 +1,582 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2021 PHYTEC Messtechnik GmbH
+ * Author: Alexander Bauer <a.bauer@phytec.de>
+ */
+
+/dts-v1/;
+#include "imx6ull.dtsi"
+#include "imx6ull-phytec-phycore-som.dtsi"
+
+/ {
+	aliases {
+		rtc0 = &i2c_rtc;
+		rtc1 = &snvs_rtc;
+	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		key {
+			label = "KEY-A";
+			gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_A>;
+			wakeup-source;
+		};
+	};
+
+	reg_adc1_vref_3v3: regulator-vref-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vref-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_s25fl064_hold: regulator-s25fl064-hold {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_s25fl064_hold>;
+		compatible = "regulator-fixed";
+		regulator-name = "s25fl064_hold";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 17 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	reg_usb_hub_vbus: regulator-hub-otg1-vbus {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbhubpwr>;
+		compatible = "regulator-fixed";
+		regulator-name = "usb_hub_vbus";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio5 5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbotg1pwr>;
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg1_vbus";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	user_leds: user-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_user_leds>,
+			    <&pinctrl_user_leds_snvs>;
+
+		user-led1 {
+			label = "yellow";
+			gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "none";
+		};
+
+		user-led2 {
+			label = "red";
+			gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "none";
+		};
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	status = "okay";
+};
+
+&ecspi1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>,
+		    <&pinctrl_ecspi1_cs>;
+	cs-gpios = <&gpio3 26 GPIO_ACTIVE_LOW>,
+		   <&gpio3 10 GPIO_ACTIVE_LOW>,
+		   <&gpio3 11 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	tpm_tis: tpm@1 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tpm>;
+		compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
+		reg = <1>;
+		spi-max-frequency = <20000000>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	s25fl064: flash@2 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = " jedec,spi-nor";
+		reg = <2>;
+		spi-max-frequency = <40000000>;
+		m25p,fast-read;
+		status = "disabled";
+	};
+};
+
+&ecspi3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3>;
+	cs-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+	dmas = <&sdma 7 8 0>,
+	       <&sdma 8 8 0>;
+	dma-names = "rx", "tx";
+	status = "okay";
+};
+
+&ethphy1 {
+	status = "okay";
+};
+
+&fec1 {
+	status = "okay";
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy2>;
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+
+	tmp102: tmp@49 {
+		compatible = "ti,tmp102";
+		reg = <0x49>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tempsense>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		#thermal-sensor-cells = <1>;
+	};
+
+	i2c_rtc: rtc@68 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc_int>;
+		compatible = "microcrystal,rv4162";
+		reg = <0x68>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	sda-gpios = <&gpio1 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	scl-gpios = <&gpio1 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&i2c3 {
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	pinctrl-1 = <&pinctrl_i2c3_gpio>;
+	sda-gpios = <&gpio3 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	scl-gpios = <&gpio3 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&i2c4 {
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	pinctrl-1 = <&pinctrl_i2c4_gpio>;
+	sda-gpios = <&gpio3 7 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	scl-gpios = <&gpio3 8 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&mdio {
+	ethphy2: ethernet-phy@2 {
+		reg = <2>;
+		micrel,led-mode = <1>;
+		clocks = <&clks IMX6UL_CLK_ENET2_REF>;
+		clock-names = "rmii-ref";
+		status = "okay";
+	};
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
+&pwm6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm6>;
+	status = "okay";
+};
+
+&pwm7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm7>;
+	status = "okay";
+};
+
+&pwm8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm8>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+/* UART4 * RS485  */
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	rts-gpios = <&gpio3 2 GPIO_ACTIVE_HIGH>;
+	linux,rs485-enabled-at-boot-time;
+	status = "okay";
+};
+
+/* UART5 * RS232  */
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart7>;
+	status = "okay";
+};
+
+/* USB */
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_otg1>;
+	vbus-supply = <&reg_usb_otg1_vbus>;
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&usbotg2 {
+	vbus-supply = <&reg_usb_hub_vbus>;
+	disable-over-current;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	wakeup-source;
+	status = "okay";
+};
+
+&usdhc2 {
+	status = "disabled";
+};
+
+&iomuxc_snvs {
+	pinctrl_rtc_int: rtcintgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x17059
+		>;
+	};
+
+	pinctrl_stmpe: stmpegrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x17059
+		>;
+	};
+
+	pinctrl_tempsense: tempsensegrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x17059
+		>;
+	};
+
+	pinctrl_tpm: tpmgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x17059
+		>;
+	};
+
+	pinctrl_usbhubpwr: usbhubpwrgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x17059
+		>;
+	};
+
+	pinctrl_user_leds_snvs: user_ledsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09	0x79
+		>;
+	};
+};
+
+&iomuxc {
+	pinctrl_gpio: gpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA05__GPIO4_IO26	0x17059  /* nUART_MUX_RS232 */
+			MX6UL_PAD_CSI_DATA04__GPIO4_IO25	0x17059  /* nUART_MUX_DUAL_RX_TX */
+		>;
+	};
+
+	pinctrl_gpio_keys: gpiokeysgrp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18	0x79
+		>;
+	};
+
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_RX_DATA__ECSPI3_SCLK	0x100b1
+			MX6UL_PAD_UART2_RTS_B__ECSPI3_MISO	0x100b1
+			MX6UL_PAD_UART2_CTS_B__ECSPI3_MOSI	0x100b1
+			MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20	0x10b0
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA20__ECSPI1_SCLK	0x100b1
+			MX6UL_PAD_LCD_DATA23__ECSPI1_MISO	0x100b1
+			MX6UL_PAD_LCD_DATA22__ECSPI1_MOSI	0x100b1
+		>;
+	};
+
+	pinctrl_ecspi1_cs: ecspi1csgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA21__GPIO3_IO26	0x10b0
+			MX6UL_PAD_LCD_DATA05__GPIO3_IO10	0x10b0
+			MX6UL_PAD_LCD_DATA06__GPIO3_IO11	0x10b0
+		>;
+	};
+
+
+	pinctrl_enet2: enet2grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN	0x1b010
+			MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00	0x1b010
+			MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01	0x1b010
+			MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	0x4001b010
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX	0x0b0b0
+			MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX	0x0b0b0
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA10__FLEXCAN2_TX	0x0b0b0
+			MX6UL_PAD_LCD_DATA11__FLEXCAN2_RX	0x0b0b0
+		>;
+	};
+
+	princtrl_flexcan2_en: flexcan2engrp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18	0x17059
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__I2C2_SCL	0xb0
+			MX6UL_PAD_GPIO1_IO01__I2C2_SDA	0xb0
+		>;
+	};
+
+	pinctrl_i2c2_gpio: i2c2gpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__GPIO1_IO00	0xb0
+			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01	0xb0
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA01__I2C3_SCL	0xb0
+			MX6UL_PAD_LCD_DATA00__I2C3_SDA	0xb0
+		>;
+	};
+
+	pinctrl_i2c3_gpio: i2c3gpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA01__GPIO3_IO06	0xb0
+			MX6UL_PAD_LCD_DATA00__GPIO3_IO05	0xb0
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA03__I2C4_SCL	0xb0
+			MX6UL_PAD_LCD_DATA02__I2C4_SDA	0xb0
+		>;
+	};
+
+	pinctrl_i2c4_gpio: i2c4gpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA03__GPIO3_IO08	0xb0
+			MX6UL_PAD_LCD_DATA02__GPIO3_IO07	0xb0
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO04__PWM3_OUT	0x0b0b0
+		>;
+	};
+
+	pinctrl_pwm6: pwm6grp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TDI__PWM6_OUT	0x0b0b0
+		>;
+	};
+
+	pinctrl_pwm7: pwm7grp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TCK__PWM7_OUT	0x0b0b0
+		>;
+	};
+
+	pinctrl_pwm8: pwm8grp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TRST_B__PWM8_OUT	0x0b0b0
+		>;
+	};
+
+	pinctrl_s25fl064_hold: s25fl064holdgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA12__GPIO3_IO17	0x100b1
+		>;
+	};
+
+	pinctrl_sai2: sai2grp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK	0x17088
+			MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC	0x17088
+			MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA	0x11088
+			MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA	0x11088
+			MX6UL_PAD_JTAG_TMS__SAI2_MCLK		0x17088
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_CLK__UART4_DCE_TX		0x1b0b1
+			MX6UL_PAD_LCD_ENABLE__UART4_DCE_RX	0x1b0b1
+			MX6UL_PAD_LCD_HSYNC__GPIO3_IO02	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart7: uart7grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA16__UART7_DCE_TX	0x1b0b1
+			MX6UL_PAD_LCD_DATA17__UART7_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_usb_otg1: usbotg1grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA06__GPIO4_IO27	0x80
+		>;
+	};
+
+	pinctrl_usbotg1pwr: usbotg1pwrgrp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA07__GPIO4_IO28	0x17059
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10059
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x17059
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170b9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100b9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170b9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170b9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170b9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170f9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100f9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170f9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170f9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170f9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170f9
+		>;
+	};
+
+	pinctrl_user_leds: userledsgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0x79
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ull-pinfunc-snvs.h b/arch/arm/boot/dts/nxp/imx/imx6ull-pinfunc-snvs.h
index 54cfe72295aa..54cfe72295aa 100644
--- a/arch/arm/boot/dts/imx6ull-pinfunc-snvs.h
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-pinfunc-snvs.h
diff --git a/arch/arm/boot/dts/imx6ull-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx6ull-pinfunc.h
index 7328d4ef8559..7328d4ef8559 100644
--- a/arch/arm/boot/dts/imx6ull-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-pinfunc.h
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-seeed-npi-dev-board-emmc.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-seeed-npi-dev-board-emmc.dts
new file mode 100644
index 000000000000..cfcd8783c31d
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-seeed-npi-dev-board-emmc.dts
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2024 Linumiz
+ * Author: Parthiban <parthiban@linumiz.com>
+ */
+
+/dts-v1/;
+#include "imx6ull.dtsi"
+#include "imx6ull-seeed-npi.dtsi"
+#include "imx6ull-seeed-npi-dev-board.dtsi"
+
+/ {
+	model = "Seeed NPi iMX6ULL Dev Board with NAND";
+	compatible = "seeed,imx6ull-seeed-npi-emmc", "seeed,imx6ull-seeed-npi", "fsl,imx6ull";
+};
+
+&usdhc2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-seeed-npi-dev-board-nand.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-seeed-npi-dev-board-nand.dts
new file mode 100644
index 000000000000..87c9434b09c5
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-seeed-npi-dev-board-nand.dts
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2024 Linumiz
+ * Author: Parthiban <parthiban@linumiz.com>
+ */
+
+/dts-v1/;
+#include "imx6ull.dtsi"
+#include "imx6ull-seeed-npi.dtsi"
+#include "imx6ull-seeed-npi-dev-board.dtsi"
+
+/ {
+	model = "Seeed NPi iMX6ULL Dev Board with NAND";
+	compatible = "seeed,imx6ull-seeed-npi-nand", "seeed,imx6ull-seeed-npi", "fsl,imx6ull";
+};
+
+&gpmi {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-seeed-npi-dev-board.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-seeed-npi-dev-board.dtsi
new file mode 100644
index 000000000000..28fddbcdc55e
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-seeed-npi-dev-board.dtsi
@@ -0,0 +1,424 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2024 Linumiz
+ * Author: Parthiban <parthiban@linumiz.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	gpio_buttons: gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_button>;
+
+		button-0 {
+			gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
+			label = "SW2";
+			linux,code = <KEY_A>;
+			wakeup-source;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+
+		led-blue {
+			gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
+			label = "LED_B";
+			linux,default-trigger = "heartbeat";
+			default-state = "on";
+		};
+
+		led-green {
+			gpios = <&gpio4 20 GPIO_ACTIVE_LOW>;
+			label = "LED_G";
+			linux,default-trigger = "heartbeat";
+			default-state = "on";
+		};
+
+		led-red {
+			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+			label = "LED_R";
+			linux,default-trigger = "heartbeat";
+			default-state = "on";
+		};
+
+		led-user {
+			gpios = <&gpio5 3 GPIO_ACTIVE_LOW>;
+			label = "User";
+			linux,default-trigger = "heartbeat";
+			default-state = "on";
+		};
+	};
+
+	reg_5v_sys: regulator-5v-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "5V_SYS";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&reg_5v_sys>;
+	};
+
+	reg_3v3_in: regulator-3v3-in {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3_IN";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		vin-supply = <&reg_5v_sys>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		vin-supply = <&reg_3v3_in>;
+	};
+
+	reg_sd1_vmmc: regulator-sd1-vmmc {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3_SD";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_vmmc>;
+		enable-active-high;
+		regulator-always-on;
+		vin-supply = <&reg_3v3>;
+	};
+};
+
+&csi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_csi1>;
+	status = "disabled"; /* LED Blue & Green shared */
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy0>;
+	status = "okay";
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy1>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@2 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <2>;
+			micrel,led-mode = <1>;
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			clock-names = "rmii-ref";
+		};
+
+		ethphy1: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			micrel,led-mode = <1>;
+			clocks = <&clks IMX6UL_CLK_ENET2_REF>;
+			clock-names = "rmii-ref";
+		};
+	};
+};
+
+&lcdif {
+	pinctrl-0 = <&pinctrl_lcdif>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+&reg_dcdc_3v3 {
+	vin-supply = <&reg_3v3_in>;
+};
+
+&sai2 {
+	assigned-clock-rates = <320000000>;
+	assigned-clocks = <&clks IMX6UL_CLK_PLL3_PFD2>;
+	pinctrl-0 = <&pinctrl_sai2>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&snvs_poweroff {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-0 = <&pinctrl_uart2>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-0 = <&pinctrl_uart3>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&uart5 {
+	pinctrl-0 = <&pinctrl_uart5>;
+	status = "okay";
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_otg1_id>;
+	dr_mode = "otg";
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_usdhc1_cd>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz &pinctrl_usdhc1_cd>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz &pinctrl_usdhc1_cd>;
+	cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	wakeup-source;
+	vmmc-supply = <&reg_sd1_vmmc>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_button: buttongrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x0b0b0
+		>;
+	};
+
+	pinctrl_csi1: csi1grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_PIXCLK__CSI_PIXCLK	0x1b088
+			MX6UL_PAD_CSI_VSYNC__CSI_VSYNC		0x1b088
+			MX6UL_PAD_CSI_HSYNC__CSI_HSYNC		0x1b088
+			MX6UL_PAD_CSI_DATA00__CSI_DATA02	0x1b088
+			MX6UL_PAD_CSI_DATA01__CSI_DATA03	0x1b088
+			MX6UL_PAD_CSI_DATA02__CSI_DATA04	0x1b088
+			MX6UL_PAD_CSI_DATA03__CSI_DATA05	0x1b088
+			MX6UL_PAD_CSI_DATA04__CSI_DATA06	0x1b088
+			MX6UL_PAD_CSI_DATA05__CSI_DATA07	0x1b088
+			MX6UL_PAD_CSI_DATA06__CSI_DATA08	0x1b088
+			MX6UL_PAD_CSI_DATA07__CSI_DATA09	0x1b088
+		>;
+	};
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN      0x1b0b0
+			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER      0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN      0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1  0x4001b031
+		>;
+	};
+
+	pinctrl_enet2: enet2grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO07__ENET2_MDC         0x1b0b0
+			MX6UL_PAD_GPIO1_IO06__ENET2_MDIO        0x1b0b0
+			MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN      0x1b0b0
+			MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER      0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0
+			MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN      0x1b0b0
+			MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0
+			MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0
+			MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2  0x4001b031
+		>;
+	};
+
+	pinctrl_gpio_leds: ledgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO04__GPIO1_IO04	0x0b0b0
+			MX6UL_PAD_CSI_VSYNC__GPIO4_IO19		0x0b0b0
+			MX6UL_PAD_CSI_HSYNC__GPIO4_IO20		0x0b0b0
+			MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x0b0b0
+		>;
+	};
+
+	pinctrl_lcdif: lcdif-grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_CLK__LCDIF_CLK		0x79
+			MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE	0x79
+			MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC	0x79
+			MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC	0x79
+			MX6UL_PAD_LCD_RESET__LCDIF_RESET	0x79
+			MX6UL_PAD_LCD_DATA00__LCDIF_DATA00	0x79
+			MX6UL_PAD_LCD_DATA01__LCDIF_DATA01	0x79
+			MX6UL_PAD_LCD_DATA02__LCDIF_DATA02	0x79
+			MX6UL_PAD_LCD_DATA03__LCDIF_DATA03	0x79
+			MX6UL_PAD_LCD_DATA04__LCDIF_DATA04	0x79
+			MX6UL_PAD_LCD_DATA05__LCDIF_DATA05	0x79
+			MX6UL_PAD_LCD_DATA06__LCDIF_DATA06	0x79
+			MX6UL_PAD_LCD_DATA07__LCDIF_DATA07	0x79
+			MX6UL_PAD_LCD_DATA08__LCDIF_DATA08	0x79
+			MX6UL_PAD_LCD_DATA09__LCDIF_DATA09	0x79
+			MX6UL_PAD_LCD_DATA10__LCDIF_DATA10	0x79
+			MX6UL_PAD_LCD_DATA11__LCDIF_DATA11	0x79
+			MX6UL_PAD_LCD_DATA12__LCDIF_DATA12	0x79
+			MX6UL_PAD_LCD_DATA13__LCDIF_DATA13	0x79
+			MX6UL_PAD_LCD_DATA14__LCDIF_DATA14	0x79
+			MX6UL_PAD_LCD_DATA15__LCDIF_DATA15	0x79
+			MX6UL_PAD_LCD_DATA16__LCDIF_DATA16	0x79
+			MX6UL_PAD_LCD_DATA17__LCDIF_DATA17	0x79
+			MX6UL_PAD_LCD_DATA18__LCDIF_DATA18	0x79
+			MX6UL_PAD_LCD_DATA19__LCDIF_DATA19	0x79
+			MX6UL_PAD_LCD_DATA20__LCDIF_DATA20	0x79
+			MX6UL_PAD_LCD_DATA21__LCDIF_DATA21	0x79
+			MX6UL_PAD_LCD_DATA22__LCDIF_DATA22	0x79
+			MX6UL_PAD_LCD_DATA23__LCDIF_DATA23	0x79
+			MX6UL_PAD_GPIO1_IO08__GPIO1_IO08	0x79
+		>;
+	};
+
+	pinctrl_reg_vmmc: usdhc1regvmmc-grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO09__GPIO1_IO09	0x17059
+		>;
+	};
+
+	pinctrl_sai2: sai2-grp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA	0x130b0
+			MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK	0x17088
+			MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC	0x17088
+			MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA	0x120b0
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX	0x1b0b1
+			MX6UL_PAD_UART2_CTS_B__UART2_DCE_CTS	0x1b0b1
+			MX6UL_PAD_UART2_RTS_B__UART2_DCE_RTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX	0x1b0b1
+			MX6UL_PAD_UART3_CTS_B__UART3_DCE_CTS	0x1b0b1
+			MX6UL_PAD_UART3_RTS_B__UART3_DCE_RTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_TX_DATA__UART4_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART4_RX_DATA__UART4_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_usb_otg1_id: usbotg1idgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID	0x17059
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10059
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170b9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100b9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170b9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170b9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170b9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170f9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100f9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170f9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170f9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170f9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170f9
+		>;
+	};
+
+	pinctrl_usdhc1_cd: usdhc1cd-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x17059
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-seeed-npi.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-seeed-npi.dtsi
new file mode 100644
index 000000000000..278152875f8e
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-seeed-npi.dtsi
@@ -0,0 +1,155 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2024 Linumiz
+ * Author: Parthiban <parthiban@linumiz.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Seeed NPi-iMX6ULL Dev Board";
+	compatible = "seeed,imx6ull-seeed-npi", "fsl,imx6ull";
+
+	reg_dcdc_3v3: regulator-dcdc-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "DCDC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_dram_1v35: regulator-dram-1v35 {
+		compatible = "regulator-fixed";
+		regulator-name = "DRAM_1V35";
+		regulator-min-microvolt = <1350000>;
+		regulator-max-microvolt = <1350000>;
+		regulator-always-on;
+		vin-supply = <&reg_dcdc_3v3>;
+	};
+
+	reg_vdd_arm_soc_in: regulator-vdd-arm-soc-in {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_ARM_SOC_IN";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-always-on;
+		vin-supply = <&reg_dcdc_3v3>;
+	};
+
+	reg_dcdc_1v8: regulator-dcdc-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "DCDC_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		vin-supply = <&reg_dcdc_3v3>;
+	};
+
+	reg_sd1_vqmmc: regulator-sd1-vqmmc {
+		compatible = "regulator-fixed";
+		regulator-name = "NVCC_SD";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_vqmmc>;
+		regulator-always-on;
+		vin-supply = <&reg_dcdc_1v8>;
+	};
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	status = "disabled";
+};
+
+&usdhc1 {
+	vqmmc-supply = <&reg_sd1_vqmmc>;
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	keep-power-in-suspend;
+	status = "disabled";
+};
+
+&iomuxc {
+	pinctrl_gpmi_nand: gpminandgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_DQS__RAWNAND_DQS		0x0b0b1
+			MX6UL_PAD_NAND_CLE__RAWNAND_CLE		0x0b0b1
+			MX6UL_PAD_NAND_ALE__RAWNAND_ALE		0x0b0b1
+			MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B	0x0b0b1
+			MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B	0x0b000
+			MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B	0x0b0b1
+			MX6UL_PAD_NAND_CE1_B__RAWNAND_CE1_B	0x0b0b1
+			MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B	0x0b0b1
+			MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B	0x0b0b1
+			MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00	0x0b0b1
+			MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01	0x0b0b1
+			MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02	0x0b0b1
+			MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03	0x0b0b1
+			MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04	0x0b0b1
+			MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05	0x0b0b1
+			MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06   0x0b0b1
+			MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07	0x0b0b1
+		>;
+	};
+
+	pinctrl_reg_vqmmc: usdhc1regvqmmcgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO05__GPIO1_IO05	0x17059
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x10069
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x17059
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x17059
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x17059
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x17059
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x17059
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x17059
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x17059
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x17059
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x17059
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhz-grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x100b9
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x170b9
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x170b9
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x170b9
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x170b9
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x170b9
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x170b9
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x170b9
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x170b9
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhz-grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x100f9
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x170f9
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x170f9
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x170f9
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x170f9
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x170f9
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x170f9
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x170f9
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x170f9
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x170f9
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-common.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-common.dtsi
new file mode 100644
index 000000000000..5248a058230c
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-common.dtsi
@@ -0,0 +1,853 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright (C) 2023 chargebyte GmbH
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pwm/pwm.h>
+#include "imx6ull.dtsi"
+
+/ {
+	aliases {
+		mmc0 = &usdhc2; /* eMMC */
+	};
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		pinctrl-0 = <&pinctrl_emmc_rst>;
+		pinctrl-names = "default";
+		reset-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>;
+	};
+
+	reg_dcdc_3v3: regulator-dcdc-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "dcdc-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "ldo-1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_status_leds>;
+
+		led-1 {
+			function = LED_FUNCTION_BOOT;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "timer";
+		};
+
+		led-2 {
+			function = LED_FUNCTION_PROGRAMMING;
+			color = <LED_COLOR_ID_YELLOW>;
+			gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-3 {
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&adc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc_motor
+		     &pinctrl_adc_cp
+		     &pinctrl_adc_pp>;
+	vref-supply = <&vgen1_reg>;
+	status = "okay";
+};
+
+&cpu0 {
+	clock-frequency = <792000000>;
+};
+
+&ecspi2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	num-cs = <3>;
+	cs-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH
+		    &gpio3 2  GPIO_ACTIVE_HIGH
+		    &gpio3 4  GPIO_ACTIVE_HIGH>;
+};
+
+&ecspi4 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi4>;
+	num-cs = <1>;
+	cs-gpios = <&gpio2 15 GPIO_ACTIVE_HIGH>;
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1
+		     &pinctrl_enet1_phy_rst
+		     &pinctrl_enet_mdio>;
+	phy-supply = <&reg_dcdc_3v3>;
+	phy-mode = "rmii";
+	phy-reset-gpios = <&gpio5 6 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <25>;
+	phy-handle = <&ethphy0>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_enet1_phy_int>;
+			interrupt-parent = <&gpio2>;
+			interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+			interrupts-extended = <&gpio2 7 IRQ_TYPE_EDGE_FALLING>;
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			clock-names = "rmii-ref";
+			max-speed = <100>;
+			smsc,disable-energy-detect;
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names = "",				/* 0 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",				/* 5 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",				/* 10 */
+			  "",
+			  "",
+			  "CP_INVERT",
+			  "",
+			  "",				/* 15 */
+			  "",
+			  "",
+			  "",
+			  "MOTOR_1_FAULT_N",
+			  "",				/* 20 */
+			  "",
+			  "ROTARY_SWITCH_1_2_N",
+			  "ROTARY_SWITCH_1_4_N",
+			  "ROTARY_SWITCH_1_8_N",
+			  "MOTOR_2_FAULT_N";		/* 25 */
+};
+
+&gpio3 {
+	gpio-line-names = "",				/* 0 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",				/* 5 */
+			  "EXT_GPIO",
+			  "MOTOR_1_DRIVER_IN1_N",
+			  "MOTOR_1_DRIVER_IN2",
+			  "MOTOR_2_DRIVER_IN1",
+			  "STM32_BOOT0",		/* 10 */
+			  "STM32_RST_N",
+			  "RELAY_1_ENABLE",
+			  "RELAY_2_ENABLE",
+			  "",
+			  "",				/* 15 */
+			  "QCA700X_MAINS_BOOTLOADER_N",
+			  "QCA700X_CP_RST_N",
+			  "QCA700X_CP_BOOTLOADER_N",
+			  "",
+			  "DIGITAL_OUT_1",		/* 20 */
+			  "DIGITAL_OUT_2",
+			  "DIGITAL_OUT_3",
+			  "DIGITAL_OUT_4",
+			  "DIGITAL_OUT_5",
+			  "DIGITAL_OUT_6",		/* 25 */
+			  "ROTARY_SWITCH_2_8_N",
+			  "ROTARY_SWITCH_2_4_N",
+			  "ROTARY_SWITCH_2_2_N";
+};
+
+&gpio4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pmic>;
+
+	gpio-line-names = "",				/* 0 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",				/* 5 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",				/* 10 */
+			  "",
+			  "",
+			  "BOARD_VARIANT_1",
+			  "BOARD_VARIANT_2",
+			  "BOARD_VARIANT_0",		/* 15 */
+			  "BOARD_VARIANT_3",
+			  "",
+			  "ROTARY_SWITCH_2_1_N",
+			  "",
+			  "DIGITAL_IN_5",		/* 20 */
+			  "",
+			  "",
+			  "DIGITAL_IN_6",
+			  "",
+			  "DIGITAL_IN_1",		/* 25 */
+			  "DIGITAL_IN_2",
+			  "DIGITAL_IN_4",
+			  "DIGITAL_IN_3";
+
+	pmic-int-hog {
+		gpio-hog;
+		gpios = <19 0>;
+		input;
+	};
+};
+
+&gpio5 {
+	gpio-line-names = "ROTARY_SWITCH_1_1_N",	/* 0 */
+			  "",
+			  "RELAY_2_SENSE",
+			  "RELAY_1_SENSE",
+			  "",
+			  "",				/* 5 */
+			  "",
+			  "QCA700X_MAINS_RST_N",
+			  "MOTOR_2_DRIVER_IN2",
+			  "",
+			  "CP_POSITIVE_PEAK_RST",	/* 10 */
+			  "CP_NEGATIVE_PEAK_RST";
+};
+
+&i2c4 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	pinctrl-1 = <&pinctrl_i2c4_gpio>;
+	scl-gpios = <&gpio1 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio1 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	pfuze3001: pmic@8 {
+		compatible = "fsl,pfuze3001";
+		reg = <0x08>;
+
+		regulators {
+			sw1_reg: sw1 {
+				regulator-name = "SW1";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw2_reg: sw2 {
+				regulator-name = "SW2";
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3_reg: sw3 {
+				regulator-name = "SW3";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1650000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-name = "VSNVS";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vldo1 {
+				regulator-name = "VLDO1";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen2_reg: vldo2 {
+				regulator-name = "VLDO2";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+				regulator-always-on;
+			};
+
+			vgen3_reg: vccsd {
+				regulator-name = "VCCSD";
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen4_reg: v33 {
+				regulator-name = "V33";
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vldo3 {
+				regulator-name = "VLDO3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vldo4 {
+				regulator-name = "VLDO4";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+
+	onewire@18 {
+		compatible = "maxim,ds2484";
+		reg = <0x18>;
+	};
+
+	accelerometer@19 {
+		compatible = "st,iis328dq", "st,h3lis331dl-accel";
+		reg = <0x19>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_accelerometer_int1_snvs>;
+		vdd-supply = <&reg_dcdc_3v3>;
+		vddio-supply = <&reg_dcdc_3v3>;
+		st,drdy-int-pin = <1>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <5 IRQ_TYPE_EDGE_RISING>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_board_var
+		     &pinctrl_digital_input
+		     &pinctrl_digital_output
+		     &pinctrl_gpio_motor
+		     &pinctrl_hog_pins
+		     &pinctrl_rotary_switch1
+		     &pinctrl_rotary_switch2>;
+
+	pinctrl_adc_cp: adc-cpgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02            0xb0
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03            0xb0
+		>;
+	};
+
+	pinctrl_adc_motor: adc-motorgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__GPIO1_IO00            0xb0
+			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01            0xb0
+			MX6UL_PAD_GPIO1_IO04__GPIO1_IO04            0xb0
+		>;
+	};
+
+	pinctrl_adc_pp: adc-ppgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO05__GPIO1_IO05            0xb0
+		>;
+	};
+
+	pinctrl_board_var: board-vargrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_CLE__GPIO4_IO15              0xb0
+			MX6UL_PAD_NAND_CE0_B__GPIO4_IO13            0xb0
+			MX6UL_PAD_NAND_CE1_B__GPIO4_IO14            0xb0
+			MX6UL_PAD_NAND_DQS__GPIO4_IO16              0xb0
+		>;
+	};
+
+	pinctrl_digital_input: digital-inputgrp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA04__GPIO4_IO25            0xb0
+			MX6UL_PAD_CSI_DATA05__GPIO4_IO26            0xb0
+			MX6UL_PAD_CSI_DATA07__GPIO4_IO28            0xb0
+			MX6UL_PAD_CSI_DATA06__GPIO4_IO27            0xb0
+			MX6UL_PAD_CSI_HSYNC__GPIO4_IO20             0xb0
+			MX6UL_PAD_CSI_DATA02__GPIO4_IO23            0xb0
+		>;
+	};
+
+	pinctrl_digital_output: digital-outputgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA15__GPIO3_IO20            0x400000b0
+			MX6UL_PAD_LCD_DATA16__GPIO3_IO21            0x400000b0
+			MX6UL_PAD_LCD_DATA17__GPIO3_IO22            0x400000b0
+			MX6UL_PAD_LCD_DATA18__GPIO3_IO23            0x400000b0
+			MX6UL_PAD_LCD_DATA19__GPIO3_IO24            0x400000b0
+			MX6UL_PAD_LCD_DATA20__GPIO3_IO25            0x400000b0
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29         0x10b0
+			MX6UL_PAD_LCD_HSYNC__GPIO3_IO02             0xb0
+			MX6UL_PAD_LCD_RESET__GPIO3_IO04             0xb0
+			MX6UL_PAD_UART4_TX_DATA__ECSPI2_SCLK        0x10b0
+			MX6UL_PAD_UART5_RX_DATA__ECSPI2_MISO        0x10b0
+			MX6UL_PAD_UART5_TX_DATA__ECSPI2_MOSI        0x10b0
+		>;
+	};
+
+	pinctrl_ecspi4: ecspi4grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15           0x10b0
+			MX6UL_PAD_ENET2_TX_DATA1__ECSPI4_SCLK       0x10b0
+			MX6UL_PAD_ENET2_TX_CLK__ECSPI4_MISO         0x10b0
+			MX6UL_PAD_ENET2_TX_EN__ECSPI4_MOSI          0x10b0
+		>;
+	};
+
+	pinctrl_emmc_rst: emmc-rstgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10              0x400010b0
+		>;
+	};
+
+	pinctrl_enet_mdio: enet-mdiogrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO            0x10b0
+			MX6UL_PAD_GPIO1_IO07__ENET1_MDC             0x10b0
+		>;
+	};
+
+	pinctrl_enet1_phy_int: enet1-phy-intgrp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_ER__GPIO2_IO07           0x10b0
+		>;
+	};
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00     0x100b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01     0x100b0
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN          0x100b0
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1      0x400000b1
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00     0xb0
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01     0xb0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN          0xb0
+		>;
+	};
+
+	pinctrl_ext_uart: ext-uartgrp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_TX_DATA0__UART7_DCE_RX      0xb0
+			MX6UL_PAD_ENET2_RX_EN__UART7_DCE_TX         0xb0
+		>;
+	};
+
+	pinctrl_fan_enable: fan-enablegrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA00__GPIO3_IO05            0x400000b0
+		>;
+	};
+
+	pinctrl_gpio_motor: gpio-motorgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA02__GPIO3_IO07            0x400000b0
+			MX6UL_PAD_LCD_DATA03__GPIO3_IO08            0x400000b0
+			MX6UL_PAD_LCD_DATA04__GPIO3_IO09            0x400000b0
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19           0xb0
+			MX6UL_PAD_UART3_RX_DATA__GPIO1_IO25         0xb0
+		>;
+	};
+
+	pinctrl_hog_pins: hog-pinsgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA07__GPIO3_IO12            0x400000b0
+			MX6UL_PAD_LCD_DATA08__GPIO3_IO13            0x400000b0
+			MX6UL_PAD_JTAG_TDI__GPIO1_IO13              0x400070a0
+			MX6UL_PAD_LCD_DATA05__GPIO3_IO10            0x400000b0
+			MX6UL_PAD_LCD_DATA06__GPIO3_IO11            0x400000b0
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_RX_DATA__I2C4_SDA           0x400008b0
+			MX6UL_PAD_UART2_TX_DATA__I2C4_SCL           0x400008b0
+		>;
+	};
+
+	pinctrl_i2c4_gpio: i2c4-gpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_RX_DATA__GPIO1_IO21         0x400008b0
+			MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20         0x400008b0
+		>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO08__USDHC2_VSELECT        0x70b1
+			MX6UL_PAD_CSI_VSYNC__GPIO4_IO19             0xb0
+		>;
+	};
+
+	pinctrl_pwm_cp: pinctrl-pwm-cpgrp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TRST_B__PWM8_OUT             0x60a0
+		>;
+	};
+
+	pinctrl_pwm_digital_input_ref: pwm-digital-input-refgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO09__PWM2_OUT              0xb0
+		>;
+	};
+
+	pinctrl_pwm_fan: pwm-fangrp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TCK__PWM7_OUT                0x60a0
+		>;
+	};
+
+	pinctrl_qca700x_cp_btld: qca700x-cp-btldgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA13__GPIO3_IO18            0x400000b0
+		>;
+	};
+
+	pinctrl_qca700x_cp_int: qca700x-cp-intgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_DATA1__GPIO2_IO19             0x10b0
+		>;
+	};
+
+	pinctrl_qca700x_cp_rst: qca700x-cp-rstgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA12__GPIO3_IO17            0x400000b0
+		>;
+	};
+
+	pinctrl_qca700x_mains_btld: qca700x-mains-btldgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA11__GPIO3_IO16            0x400000b0
+		>;
+	};
+
+	pinctrl_rotary_switch1: rotary-switch1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_CTS_B__GPIO1_IO22           0xb0
+			MX6UL_PAD_UART2_RTS_B__GPIO1_IO23           0xb0
+			MX6UL_PAD_UART3_TX_DATA__GPIO1_IO24         0xb0
+		>;
+	};
+
+	pinctrl_rotary_switch2: rotary-switch2grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_PIXCLK__GPIO4_IO18            0xb0
+			MX6UL_PAD_LCD_DATA23__GPIO3_IO28            0xb0
+			MX6UL_PAD_LCD_DATA22__GPIO3_IO27            0xb0
+			MX6UL_PAD_LCD_DATA21__GPIO3_IO26            0xb0
+		>;
+	};
+
+	pinctrl_rs485_1: rs485-1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18           0xb0
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX       0xb0
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX       0xb0
+		>;
+	};
+
+	pinctrl_rs485_2: rs485-2grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA03__GPIO4_IO24            0x10b0
+			MX6UL_PAD_CSI_DATA01__UART5_DCE_RX          0x10b0
+			MX6UL_PAD_CSI_DATA00__UART5_DCE_TX          0x10b0
+		>;
+	};
+
+	pinctrl_status_leds: status-ledsgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA09__GPIO3_IO14            0xb0
+			MX6UL_PAD_LCD_DATA10__GPIO3_IO15            0xb0
+			MX6UL_PAD_LCD_DATA14__GPIO3_IO19            0xb0
+		>;
+	};
+
+	pinctrl_stm32: stm32grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_RX_DATA1__UART6_DCE_RX      0x10b0
+			MX6UL_PAD_ENET2_RX_DATA0__UART6_DCE_TX      0x10b0
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_CLK__UART4_DTE_RX             0xb0
+			MX6UL_PAD_LCD_ENABLE__UART4_DTE_TX          0xb0
+		>;
+	};
+
+	pinctrl_usb: usbgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CLK__USB_OTG1_OC              0x70b0
+			MX6UL_PAD_SD1_DATA0__ANATOP_OTG1_ID         0x70b0
+		>;
+	};
+
+	pinctrl_usb_pwr: usb-pwrgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USB_OTG1_PWR             0xb0
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK             0x7071
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD             0x7071
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0         0x7071
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1         0x7071
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2         0x7071
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3         0x7071
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4         0x7071
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5         0x7071
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6         0x7071
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7         0x7071
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK             0x70b1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD             0x70b1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0         0x70b1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1         0x70b1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2         0x70b1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3         0x70b1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4         0x70b1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5         0x70b1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6         0x70b1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7         0x70b1
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK             0x70f1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD             0x70f1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0         0x70f1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1         0x70f1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2         0x70f1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3         0x70f1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4         0x70f1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5         0x70f1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6         0x70f1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7         0x70f1
+		>;
+	};
+
+	pinctrl_wdog2: wdoggrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_VSYNC__WDOG2_WDOG_B           0x10b0
+		>;
+	};
+};
+
+&iomuxc_snvs {
+	pinctrl-names = "default_snvs";
+	pinctrl-0 = <&pinctrl_cp_peak_snvs
+		     &pinctrl_gpio_motor_snvs
+		     &pinctrl_relay_sense_snvs
+		     &pinctrl_rotary_switch1_snvs>;
+
+	pinctrl_accelerometer_int1_snvs: accelerometer-int1-snvsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05         0x130a0
+		>;
+	};
+
+	pinctrl_cp_peak_snvs: cp-peak-snvsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_BOOT_MODE0__GPIO5_IO10           0x130a0
+			MX6ULL_PAD_BOOT_MODE1__GPIO5_IO11           0x130a0
+		>;
+	};
+
+	pinctrl_enet1_phy_rst: enet1-phy-rstgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06         0x100a0
+		>;
+	};
+
+	pinctrl_fan_sense_snvs: fan-sense-snvsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01         0x100a0
+		>;
+	};
+
+	pinctrl_gpio_motor_snvs: gpio-motor-snvsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER8__GPIO5_IO08         0x110a0
+		>;
+	};
+
+	pinctrl_qca700x_mains_int: qca700x-mains-intgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09         0x130a0
+		>;
+	};
+
+	pinctrl_qca700x_mains_rst: qca700x-mains-rstgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER7__GPIO5_IO07         0x400100a0
+		>;
+	};
+
+	pinctrl_relay_sense_snvs: relay-sense-snvsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03         0x100a0
+			MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02         0x100a0
+		>;
+	};
+
+	pinctrl_rotary_switch1_snvs: rotary-switch1-snvsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00         0x110a0
+		>;
+	};
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_digital_input_ref>;
+	status = "okay";
+};
+
+&pwm8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_cp>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rs485_1>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	fsl,dte-mode;
+	status = "okay";
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rs485_2>;
+};
+
+&uart6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_stm32>;
+	status = "okay";
+};
+
+&uart7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ext_uart>;
+	status = "okay";
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb
+		     &pinctrl_usb_pwr>;
+	dr_mode = "host";
+	power-active-high;
+	over-current-active-low;
+	disable-over-current;
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&usbphy1 {
+	fsl,tx-cal-45-dn-ohms = <35>;
+	fsl,tx-cal-45-dp-ohms = <35>;
+};
+
+&usbphy2 {
+	fsl,tx-cal-45-dn-ohms = <35>;
+	fsl,tx-cal-45-dp-ohms = <35>;
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	vmmc-supply = <&sw2_reg>;
+	vqmmc-supply = <&reg_1v8>;
+	mmc-pwrseq = <&emmc_pwrseq>;
+	bus-width = <8>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
+&wdog1 {
+	status = "disabled";
+};
+
+&wdog2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog2>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-master.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-master.dts
new file mode 100644
index 000000000000..f9bbd589b66d
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-master.dts
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright (C) 2023 chargebyte GmbH
+
+#include "imx6ull-tarragon-common.dtsi"
+
+/ {
+	model = "chargebyte Tarragon Master";
+	compatible = "chargebyte,imx6ull-tarragon-master", "fsl,imx6ull";
+
+	fan0: pwm-fan {
+		compatible = "pwm-fan";
+		pwms = <&pwm7 0 40000 PWM_POLARITY_INVERTED>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_fan_sense_snvs>;
+		fan-supply = <&reg_fan>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+	reg_fan: regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "fan-supply";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_fan_enable>;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+};
+
+&ecspi2 {
+	status = "okay";
+
+	qca700x_cp: ethernet@0 {
+		reg = <0x0>;
+		compatible = "qca,qca7000";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_qca700x_cp_int
+			     &pinctrl_qca700x_cp_rst
+			     &pinctrl_qca700x_cp_btld>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <19 IRQ_TYPE_EDGE_RISING>;
+		spi-cpha;
+		spi-cpol;
+		spi-max-frequency = <12000000>;
+	};
+};
+
+&ecspi4 {
+	status = "okay";
+
+	qca700x_mains: ethernet@0 {
+		reg = <0x0>;
+		compatible = "qca,qca7000";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_qca700x_mains_int
+			     &pinctrl_qca700x_mains_rst
+			     &pinctrl_qca700x_mains_btld>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <9 IRQ_TYPE_EDGE_RISING>;
+		spi-cpha;
+		spi-cpol;
+		spi-max-frequency = <12000000>;
+	};
+};
+
+&fec1 {
+	status = "okay";
+};
+
+&pwm7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_fan>;
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-micro.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-micro.dts
new file mode 100644
index 000000000000..e471c2005bee
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-micro.dts
@@ -0,0 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright (C) 2023 chargebyte GmbH
+
+#include "imx6ull-tarragon-common.dtsi"
+
+/ {
+	model = "chargebyte Tarragon Micro";
+	compatible = "chargebyte,imx6ull-tarragon-micro", "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-slave.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-slave.dts
new file mode 100644
index 000000000000..ef06619d7c86
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-slave.dts
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright (C) 2023 chargebyte GmbH
+
+#include "imx6ull-tarragon-common.dtsi"
+
+/ {
+	model = "chargebyte Tarragon Slave";
+	compatible = "chargebyte,imx6ull-tarragon-slave", "fsl,imx6ull";
+};
+
+&ecspi2 {
+	status = "okay";
+
+	qca700x_cp: ethernet@0 {
+		reg = <0x0>;
+		compatible = "qca,qca7000";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_qca700x_cp_int
+			     &pinctrl_qca700x_cp_rst
+			     &pinctrl_qca700x_cp_btld>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <19 IRQ_TYPE_EDGE_RISING>;
+		spi-cpha;
+		spi-cpol;
+		spi-max-frequency = <12000000>;
+	};
+};
+
+&fec1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-slavext.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-slavext.dts
new file mode 100644
index 000000000000..83db65bf630f
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-tarragon-slavext.dts
@@ -0,0 +1,64 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+//
+// Copyright (C) 2023 chargebyte GmbH
+
+#include "imx6ull-tarragon-common.dtsi"
+
+/ {
+	model = "chargebyte Tarragon SlaveXT";
+	compatible = "chargebyte,imx6ull-tarragon-slavext", "fsl,imx6ull";
+
+	fan0: pwm-fan {
+		compatible = "pwm-fan";
+		pwms = <&pwm7 0 40000 PWM_POLARITY_INVERTED>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_fan_sense_snvs>;
+		fan-supply = <&reg_fan>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+	reg_fan: regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "fan-supply";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_fan_enable>;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+};
+
+&ecspi2 {
+	status = "okay";
+
+	qca700x_cp: ethernet@0 {
+		reg = <0x0>;
+		compatible = "qca,qca7000";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_qca700x_cp_int
+			     &pinctrl_qca700x_cp_rst
+			     &pinctrl_qca700x_cp_btld>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <19 IRQ_TYPE_EDGE_RISING>;
+		spi-cpha;
+		spi-cpol;
+		spi-max-frequency = <12000000>;
+	};
+};
+
+&fec1 {
+	status = "okay";
+};
+
+&pwm7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_fan>;
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-tqma6ull2-mba6ulx.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-tqma6ull2-mba6ulx.dts
new file mode 100644
index 000000000000..e593b7036fc7
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-tqma6ull2-mba6ulx.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ull-tqma6ull2.dtsi"
+#include "mba6ulx.dtsi"
+
+/ {
+	model = "TQ-Systems TQMa6ULL2 SoM on MBa6ULx board";
+	compatible = "tq,imx6ull-tqma6ull2-mba6ulx", "tq,imx6ull-tqma6ull2", "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-tqma6ull2.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-tqma6ull2.dtsi
new file mode 100644
index 000000000000..8541cb3f3b3e
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-tqma6ull2.dtsi
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include "imx6ull.dtsi"
+#include "imx6ul-tqma6ul-common.dtsi"
+#include "imx6ul-tqma6ulx-common.dtsi"
+
+/ {
+	model = "TQ-Systems TQMa6ULL2 SoM";
+	compatible = "tq,imx6ull-tqma6ull2", "fsl,imx6ull";
+};
+
+&usdhc2 {
+	fsl,tuning-step = <6>;
+	/* Errata ERR010450 Workaround */
+	max-frequency = <99000000>;
+	assigned-clocks = <&clks IMX6UL_CLK_USDHC2_SEL>, <&clks IMX6UL_CLK_USDHC2>;
+	assigned-clock-parents = <&clks IMX6UL_CLK_PLL2_PFD2>;
+	assigned-clock-rates = <0>, <198000000>;
+};
+
+&iomuxc {
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x00017031
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x00017039
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x00017039
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x00017039
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x00017039
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x00017039
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x00017039
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x00017039
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x00017039
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x00017039
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x000170f1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x000170f1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x000170f1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x000170f1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x000170f1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x000170f1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x000170f1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x000170f1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x000170f1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x000170f1
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x000170f1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x000170f1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x000170f1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x000170f1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x000170f1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x000170f1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x000170f1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x000170f1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x000170f1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x000170f1
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-tqma6ull2l-mba6ulx.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-tqma6ull2l-mba6ulx.dts
new file mode 100644
index 000000000000..33437aae9822
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-tqma6ull2l-mba6ulx.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ull-tqma6ull2l.dtsi"
+#include "mba6ulx.dtsi"
+
+/ {
+	model = "TQ Systems TQMa6ULL2L SoM on MBa6ULx board";
+	compatible = "tq,imx6ull-tqma6ull2l-mba6ulx", "tq,imx6ull-tqma6ull2l", "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-tqma6ull2l.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-tqma6ull2l.dtsi
new file mode 100644
index 000000000000..be593d47e3b1
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-tqma6ull2l.dtsi
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include "imx6ull.dtsi"
+#include "imx6ul-tqma6ul-common.dtsi"
+#include "imx6ul-tqma6ulxl-common.dtsi"
+
+/ {
+	model = "TQ Systems TQMa6ULL2L SoM";
+	compatible = "tq,imx6ull-tqma6ull2l", "fsl,imx6ull";
+};
+
+&usdhc2 {
+	fsl,tuning-step = <6>;
+	/* Errata ERR010450 Workaround */
+	max-frequency = <99000000>;
+	assigned-clocks = <&clks IMX6UL_CLK_USDHC2_SEL>, <&clks IMX6UL_CLK_USDHC2>;
+	assigned-clock-parents = <&clks IMX6UL_CLK_PLL2_PFD2>;
+	assigned-clock-rates = <0>, <198000000>;
+};
+
+&iomuxc {
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x00017031
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x00017039
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x00017039
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x00017039
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x00017039
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x00017039
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x00017039
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x00017039
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x00017039
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x00017039
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x000170f1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x000170f1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x000170f1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x000170f1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x000170f1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x000170f1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x000170f1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x000170f1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x000170f1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x000170f1
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x000170f1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x000170f1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x000170f1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x000170f1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x000170f1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x000170f1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x000170f1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x000170f1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x000170f1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x000170f1
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts
new file mode 100644
index 000000000000..e4576d509a5b
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts
@@ -0,0 +1,566 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// Copyright (C) 2022-2024 Sebastian Reichel <sre@kernel.org>
+
+/dts-v1/;
+#include "imx6ull.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/clock/imx6ul-clock.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "UNI-T UTi260B Thermal Camera";
+	compatible = "uni-t,uti260b", "fsl,imx6ull";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	panel_backlight: backlight {
+		compatible = "pwm-backlight";
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+		enable-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&mux_backlight_enable>;
+		power-supply = <&reg_vsd>;
+		pwms = <&pwm1 0 50000 0>;
+	};
+
+	battery: battery {
+		compatible = "simple-battery";
+		/* generic 26650 battery */
+		device-chemistry = "lithium-ion";
+		charge-full-design-microamp-hours = <5000000>;
+		voltage-max-design-microvolt = <4200000>;
+		voltage-min-design-microvolt = <3300000>;
+	};
+
+	tp5000: charger {
+		compatible = "gpio-charger";
+		charger-type = "usb-sdp";
+		gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&mux_charger_stat1>;
+	};
+
+	fuel-gauge {
+		compatible = "adc-battery";
+		charged-gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+		io-channel-names = "voltage";
+		io-channels = <&adc1 7>;
+		monitored-battery = <&battery>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&mux_charger_stat2>;
+		power-supplies = <&tp5000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&mux_gpio_keys>;
+		autorepeat;
+
+		up-key {
+			label = "Up";
+			gpios = <&gpio2 11 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_UP>;
+		};
+
+		down-key {
+			label = "Down";
+			gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_DOWN>;
+		};
+
+		left-key {
+			label = "Left";
+			gpios = <&gpio2 13 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_LEFT>;
+		};
+
+		right-key {
+			label = "Right";
+			gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RIGHT>;
+		};
+
+		ok-key {
+			label = "Ok";
+			gpios = <&gpio2 9 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_ENTER>;
+		};
+
+		return-key {
+			label = "Return";
+			gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_ESC>;
+		};
+
+		play-key {
+			label = "Media";
+			gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_MEDIA>;
+		};
+
+		trigger-key {
+			label = "Trigger";
+			gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_TRIGGER>;
+		};
+
+		power-key {
+			label = "Power";
+			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+		};
+
+		light-key {
+			label = "Light";
+			gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_LIGHTS_TOGGLE>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&mux_led_ctrl>;
+
+		led {
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_FLASH;
+			gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	poweroff {
+		compatible = "gpio-poweroff";
+		gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&mux_poweroff>;
+	};
+
+	reg_vref: regulator-vref-4v2 {
+		compatible = "regulator-fixed";
+		regulator-name = "VREF_4V2";
+		regulator-min-microvolt = <4200000>;
+		regulator-max-microvolt = <4200000>;
+	};
+
+	reg_vsd: regulator-vsd {
+		compatible = "regulator-fixed";
+		regulator-name = "VSD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&adc1 {
+	#io-channel-cells = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mux_adc>;
+	vref-supply = <&reg_vref>;
+	status = "okay";
+};
+
+&csi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mux_csi>;
+	status = "okay";
+
+	port {
+		parallel_from_gc0308: endpoint {
+			remote-endpoint = <&gc0308_to_parallel>;
+		};
+	};
+};
+
+&ecspi3 {
+	cs-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mux_spi3>;
+	status = "okay";
+
+	panel@0 {
+		compatible = "inanbo,t28cp45tn89-v17";
+		reg = <0>;
+		backlight = <&panel_backlight>;
+		power-supply = <&reg_vsd>;
+		spi-cpha;
+		spi-cpol;
+		spi-max-frequency = <1000000>;
+		spi-rx-bus-width = <0>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+};
+
+&gpio1 {
+	ir-reset-hog {
+		gpio-hog;
+		gpios = <3 GPIO_ACTIVE_LOW>;
+		line-name = "ir-reset-gpio";
+		output-low;
+		pinctrl-names = "default";
+		pinctrl-0 = <&mux_ir_reset>;
+	};
+};
+
+&gpio2 {
+	/* configuring this to output-high results in poweroff */
+	power-en-hog {
+		gpio-hog;
+		gpios = <6 GPIO_ACTIVE_HIGH>;
+		line-name = "power-en-gpio";
+		output-low;
+		pinctrl-names = "default";
+		pinctrl-0 = <&mux_poweroff2>;
+	};
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mux_i2c1>;
+	status = "okay";
+
+	camera@21 {
+		compatible = "galaxycore,gc0308";
+		reg = <0x21>;
+		clocks = <&clks IMX6UL_CLK_CSI>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&mux_gc0308>;
+		powerdown-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+		vdd28-supply = <&reg_vsd>;
+
+		port {
+			gc0308_to_parallel: endpoint {
+				remote-endpoint = <&parallel_from_gc0308>;
+				bus-width = <8>;
+				data-shift = <2>; /* lines 9:2 are used */
+				hsync-active = <1>; /* active high */
+				vsync-active = <1>; /* active high */
+				data-active = <1>; /* active high */
+				pclk-sample = <1>; /* sample on rising edge */
+			};
+		};
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mux_i2c2>;
+	status = "okay";
+
+	rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&lcdif {
+	assigned-clocks = <&clks IMX6UL_CLK_LCDIF_PRE_SEL>;
+	assigned-clock-parents = <&clks IMX6UL_CLK_PLL5_VIDEO_DIV>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mux_lcd_data>, <&mux_lcd_ctrl>;
+	status = "okay";
+
+	port {
+		display_out: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mux_pwm>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mux_uart>;
+	status = "okay";
+};
+
+&usbotg1 {
+	/* USB-C connector */
+	disable-over-current;
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbotg2 {
+	/* thermal sensor */
+	disable-over-current;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbphy1 {
+	fsl,tx-d-cal = <106>;
+};
+
+&usbphy2 {
+	fsl,tx-d-cal = <106>;
+};
+
+&usdhc1 {
+	/* MicroSD */
+	cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+	keep-power-in-suspend;
+	no-1-8-v;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&mux_sdhc1>, <&mux_sdhc1_cd>;
+	pinctrl-1 = <&mux_sdhc1_100mhz>, <&mux_sdhc1_cd>;
+	pinctrl-2 = <&mux_sdhc1_200mhz>, <&mux_sdhc1_cd>;
+	wakeup-source;
+	vmmc-supply = <&reg_vsd>;
+	status = "okay";
+};
+
+&usdhc2 {
+	/* eMMC */
+	keep-power-in-suspend;
+	no-1-8-v;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mux_sdhc2>;
+	wakeup-source;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mux_wdog>;
+};
+
+&iomuxc {
+	mux_adc: adcgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO07__GPIO1_IO07		0xb0
+		>;
+	};
+
+	mux_backlight_enable: blenablegrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO09__GPIO1_IO09		0x3008
+		>;
+	};
+
+	mux_charger_stat1: charger1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01		0x3008
+		>;
+	};
+
+	mux_charger_stat2: charger2grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02		0x3008
+		>;
+	};
+
+	mux_csi: csi1grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_PIXCLK__CSI_PIXCLK		0x1b088
+			MX6UL_PAD_CSI_VSYNC__CSI_VSYNC			0x1b088
+			MX6UL_PAD_CSI_HSYNC__CSI_HSYNC			0x1b088
+			MX6UL_PAD_CSI_DATA00__CSI_DATA02		0x1b088
+			MX6UL_PAD_CSI_DATA01__CSI_DATA03		0x1b088
+			MX6UL_PAD_CSI_DATA02__CSI_DATA04		0x1b088
+			MX6UL_PAD_CSI_DATA03__CSI_DATA05		0x1b088
+			MX6UL_PAD_CSI_DATA04__CSI_DATA06		0x1b088
+			MX6UL_PAD_CSI_DATA05__CSI_DATA07		0x1b088
+			MX6UL_PAD_CSI_DATA06__CSI_DATA08		0x1b088
+			MX6UL_PAD_CSI_DATA07__CSI_DATA09		0x1b088
+		>;
+	};
+
+	mux_gc0308: gc0308grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_MCLK__CSI_MCLK			0x1e038
+			MX6UL_PAD_GPIO1_IO05__GPIO1_IO05		0x1b088
+			MX6UL_PAD_GPIO1_IO06__GPIO1_IO06		0x1b088
+		>;
+	};
+
+	mux_gpio_keys: gpiokeygrp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_TX_DATA0__GPIO2_IO11		0x3008
+			MX6UL_PAD_ENET2_TX_DATA1__GPIO2_IO12		0x3008
+			MX6UL_PAD_ENET2_TX_EN__GPIO2_IO13		0x3008
+			MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10		0x3008
+			MX6UL_PAD_ENET2_RX_DATA1__GPIO2_IO09		0x3008
+			MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15		0x3008
+			MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08		0x3008
+			MX6UL_PAD_ENET2_TX_CLK__GPIO2_IO14		0x3008
+			MX6UL_PAD_ENET1_TX_DATA0__GPIO2_IO03		0x3008
+			MX6UL_PAD_ENET1_RX_DATA1__GPIO2_IO01		0x3008
+		>;
+	};
+
+	mux_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_TX_DATA__I2C1_SCL		0x4001b8b0
+			MX6UL_PAD_UART4_RX_DATA__I2C1_SDA		0x4001b8b0
+		>;
+	};
+
+	mux_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__I2C2_SCL		0x4001f8a8
+			MX6UL_PAD_UART5_RX_DATA__I2C2_SDA		0x4001f8a8
+		>;
+	};
+
+	mux_ir_reset: irresetgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03		0x3008
+		>;
+	};
+
+	mux_lcd_ctrl: lcdifctrlgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_CLK__LCDIF_CLK			0x79
+			MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE		0x79
+			MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC		0x79
+			MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC		0x79
+		>;
+	};
+
+	mux_lcd_data: lcdifdatgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA00__LCDIF_DATA00		0x79
+			MX6UL_PAD_LCD_DATA01__LCDIF_DATA01		0x79
+			MX6UL_PAD_LCD_DATA02__LCDIF_DATA02		0x79
+			MX6UL_PAD_LCD_DATA03__LCDIF_DATA03		0x79
+			MX6UL_PAD_LCD_DATA04__LCDIF_DATA04		0x79
+			MX6UL_PAD_LCD_DATA05__LCDIF_DATA05		0x79
+			MX6UL_PAD_LCD_DATA06__LCDIF_DATA06		0x79
+			MX6UL_PAD_LCD_DATA07__LCDIF_DATA07		0x79
+			MX6UL_PAD_LCD_DATA08__LCDIF_DATA08		0x79
+			MX6UL_PAD_LCD_DATA09__LCDIF_DATA09		0x79
+			MX6UL_PAD_LCD_DATA10__LCDIF_DATA10		0x79
+			MX6UL_PAD_LCD_DATA11__LCDIF_DATA11		0x79
+			MX6UL_PAD_LCD_DATA12__LCDIF_DATA12		0x79
+			MX6UL_PAD_LCD_DATA13__LCDIF_DATA13		0x79
+			MX6UL_PAD_LCD_DATA14__LCDIF_DATA14		0x79
+			MX6UL_PAD_LCD_DATA15__LCDIF_DATA15		0x79
+			MX6UL_PAD_LCD_DATA16__LCDIF_DATA16		0x79
+			MX6UL_PAD_LCD_DATA17__LCDIF_DATA17		0x79
+		>;
+	};
+
+	mux_led_ctrl: ledctrlgrp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_EN__GPIO2_IO02		0x3008
+		>;
+	};
+
+	mux_poweroff: poweroffgrp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_TX_DATA1__GPIO2_IO04		0x3008
+		>;
+	};
+
+	mux_poweroff2: poweroff2grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_TX_CLK__GPIO2_IO06		0x3008
+		>;
+	};
+
+	mux_pwm: pwm1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO08__PWM1_OUT			0x110b0
+		>;
+	};
+
+	mux_sdhc1: sdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD			0x17059
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK			0x10071
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0		0x17059
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1		0x17059
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2		0x17059
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3		0x17059
+		>;
+	};
+
+	mux_sdhc1_100mhz: sdhc1-100mhz-grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD			0x170b9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK			0x170b9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0		0x170b9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1		0x170b9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2		0x170b9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3		0x170b9
+		>;
+	};
+
+	mux_sdhc1_200mhz: sdhc1-200mhz-grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD			0x170f9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK			0x170f9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0		0x170f9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1		0x170f9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2		0x170f9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3		0x170f9
+		>;
+	};
+
+	mux_sdhc1_cd: sdhc1-cd-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19		0x17059
+		>;
+	};
+
+	mux_sdhc2: sdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK			0x10069
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD			0x17059
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0		0x17059
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1		0x17059
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2		0x17059
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3		0x17059
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4		0x17059
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5		0x17059
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6		0x17059
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7		0x17059
+		>;
+	};
+
+	mux_spi3: ecspi3grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_CTS_B__ECSPI3_MOSI		0x100b1
+			MX6UL_PAD_UART2_RX_DATA__ECSPI3_SCLK		0x100b1
+			MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20		0x3008
+		>;
+	};
+
+	mux_uart: uartgrp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX		0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX		0x1b0b1
+		>;
+	};
+
+	mux_wdog: wdoggrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_RESET__WDOG1_WDOG_ANY		0x30b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ull.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull.dtsi
index 9bf67490ac49..db0c339022ac 100644
--- a/arch/arm/boot/dts/imx6ull.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull.dtsi
@@ -50,7 +50,7 @@
 };
 
 / {
-	soc {
+	soc: soc {
 		aips3: bus@2200000 {
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
@@ -75,7 +75,7 @@
 				clocks = <&clks IMX6UL_CLK_DUMMY>;
 			};
 
-			iomuxc_snvs: iomuxc-snvs@2290000 {
+			iomuxc_snvs: pinctrl@2290000 {
 				compatible = "fsl,imx6ull-iomuxc-snvs";
 				reg = <0x02290000 0x4000>;
 			};
@@ -88,6 +88,8 @@
 				clocks = <&clks IMX6UL_CLK_UART8_IPG>,
 					 <&clks IMX6UL_CLK_UART8_SERIAL>;
 				clock-names = "ipg", "per";
+				dmas = <&sdma 45 4 0>, <&sdma 46 4 0>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 		};
diff --git a/arch/arm/boot/dts/imx6ulz-14x14-evk.dts b/arch/arm/boot/dts/nxp/imx/imx6ulz-14x14-evk.dts
index 483d9732c002..483d9732c002 100644
--- a/arch/arm/boot/dts/imx6ulz-14x14-evk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ulz-14x14-evk.dts
diff --git a/arch/arm/boot/dts/imx6ulz-bsh-smm-m2.dts b/arch/arm/boot/dts/nxp/imx/imx6ulz-bsh-smm-m2.dts
index 59bcfc9a6b10..2d9f495660c9 100644
--- a/arch/arm/boot/dts/imx6ulz-bsh-smm-m2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ulz-bsh-smm-m2.dts
@@ -29,6 +29,14 @@
 	status = "okay";
 };
 
+&snvs_poweroff {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
 &uart3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart3>;
@@ -90,7 +98,7 @@
 };
 
 &iomuxc {
-	pinctrl_gpmi_nand: gpmi-nand {
+	pinctrl_gpmi_nand: gpminandgrp {
 		fsl,pins = <
 			MX6UL_PAD_NAND_CLE__RAWNAND_CLE		0xb0b1
 			MX6UL_PAD_NAND_ALE__RAWNAND_ALE		0xb0b1
diff --git a/arch/arm/boot/dts/imx6ulz.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ulz.dtsi
index 0b5f1a763567..0b5f1a763567 100644
--- a/arch/arm/boot/dts/imx6ulz.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ulz.dtsi
diff --git a/arch/arm/boot/dts/nxp/imx/imx7-colibri-aster.dtsi b/arch/arm/boot/dts/nxp/imx/imx7-colibri-aster.dtsi
new file mode 100644
index 000000000000..01612741f792
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7-colibri-aster.dtsi
@@ -0,0 +1,80 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2017-2022 Toradex
+ */
+
+/* Colibri AD0 to AD3 */
+&adc1 {
+	status = "okay";
+};
+
+/* Colibri SSP */
+&ecspi3 {
+	cs-gpios = <
+		&gpio4 11 GPIO_ACTIVE_LOW /* SODIMM 86 / regular SSPFRM as UNO_SPI_CS or  */
+		&gpio4 23 GPIO_ACTIVE_LOW /* SODIMM 65 / already muxed pinctrl_gpio2 as SPI_CE0_N */
+		&gpio4 22 GPIO_ACTIVE_LOW /* SODIMM 85 / already muxed pinctrl_gpio2 as SPI_CE1_N */
+	>;
+	status = "okay";
+};
+
+/* Colibri Fast Ethernet */
+&fec1 {
+	status = "okay";
+};
+
+/* Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 */
+&i2c4 {
+	status = "okay";
+};
+
+/* Colibri PWM<A> */
+&pwm1 {
+	status = "okay";
+};
+
+/* Colibri PWM<B> */
+&pwm2 {
+	status = "okay";
+};
+
+/* Colibri PWM<C> */
+&pwm3 {
+	status = "okay";
+};
+
+/* Colibri PWM<D> */
+&pwm4 {
+	status = "okay";
+};
+
+/* M41T0M6 real time clock */
+&rtc {
+	status = "okay";
+};
+
+/* Colibri UART_A */
+&uart1 {
+	status = "okay";
+};
+
+/* Colibri UART_B */
+&uart2 {
+	status = "okay";
+};
+
+/* Colibri UART_C */
+&uart3 {
+	status = "okay";
+};
+
+/* Colibri USBC */
+&usbotg1 {
+	disable-over-current;
+	status = "okay";
+};
+
+/* Colibri MMC/SD */
+&usdhc1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7-colibri-eval-v3.dtsi b/arch/arm/boot/dts/nxp/imx/imx7-colibri-eval-v3.dtsi
new file mode 100644
index 000000000000..326440f2b4f4
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7-colibri-eval-v3.dtsi
@@ -0,0 +1,111 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2016-2022 Toradex
+ */
+
+/ {
+	/* Fixed crystal dedicated to MCP2515. */
+	clk16m: clk16m {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <16000000>;
+	};
+};
+
+/* Colibri AD0 to AD3 */
+&adc1 {
+	status = "okay";
+};
+
+/*
+ * The Atmel maxtouch controller uses SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2, pwm3.
+ * So if you enable following capacitive touch controller, disable pwm2/pwm3 first.
+ */
+&atmel_mxt_ts {
+	interrupt-parent = <&gpio1>;
+	interrupts = <9 IRQ_TYPE_EDGE_FALLING>;		/* SODIMM 28 / INT */
+	pinctrl-0 = <&pinctrl_atmel_adapter>;
+	reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;	/* SODIMM 30 / RST */
+	status = "disabled";
+};
+
+/* Colibri SSP */
+&ecspi3 {
+	status = "okay";
+
+	mcp2515: can@0 {
+		clocks = <&clk16m>;
+		compatible = "microchip,mcp2515";
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can_int>;
+		reg = <0>;
+		spi-max-frequency = <10000000>;
+		vdd-supply = <&reg_3v3>;
+		xceiver-supply = <&reg_5v0>;
+	};
+};
+
+/* Colibri Fast Ethernet */
+&fec1 {
+	status = "okay";
+};
+
+/* Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 */
+&i2c4 {
+	status = "okay";
+};
+
+/* Colibri PWM<A> */
+&pwm1 {
+	status = "okay";
+};
+
+/* Colibri PWM<B> */
+&pwm2 {
+	/* The pwm2 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri PWM<C> */
+&pwm3 {
+	/* The pwm3 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri PWM<D> */
+&pwm4 {
+	status = "okay";
+};
+
+/* M41T0M6 real time clock */
+&rtc {
+	status = "okay";
+};
+
+/* Colibri UART_A */
+&uart1 {
+	status = "okay";
+};
+
+/* Colibri UART_B */
+&uart2 {
+	status = "okay";
+};
+
+/* Colibri UART_C */
+&uart3 {
+	status = "okay";
+};
+
+/* Colibri USBC */
+&usbotg1 {
+	disable-over-current;
+	status = "okay";
+};
+
+/* Colibri MMC/SD */
+&usdhc1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7-colibri-iris-v2.dtsi b/arch/arm/boot/dts/nxp/imx/imx7-colibri-iris-v2.dtsi
new file mode 100644
index 000000000000..b687727f956a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7-colibri-iris-v2.dtsi
@@ -0,0 +1,113 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/ {
+	reg_3v3_vmmc: regulator-3v3-vmmc {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio5 16 GPIO_ACTIVE_HIGH>; /* SODIMM 100 */
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "3v3_vmmc";
+		startup-delay-us = <100>;
+	};
+};
+
+/* Colibri AD0 to AD3 */
+&adc1 {
+	status = "okay";
+};
+
+/* Colibri SSP */
+&ecspi3 {
+	status = "okay";
+};
+
+/* Colibri Fast Ethernet */
+&fec1 {
+	status = "okay";
+};
+
+&gpio2 {
+	/*
+	 * uart_b_c_on_x14_enable turns the UART transceiver for UART2 and 5 on. If one wants to
+	 * turn the transceiver off, that property has to be deleted and the gpio handled in
+	 * userspace.
+	 * The same applies to uart_a_on_x13_enable where the UART_A transceiver is turned on.
+	 */
+	uart-b-c-on-x14-enable-hog {
+		gpio-hog;
+		gpios = <27 GPIO_ACTIVE_HIGH>; /* SODIMM 104 */
+		output-high;
+	};
+};
+
+&gpio5 {
+	uart-a-on-x13-enable-hog {
+		gpio-hog;
+		gpios = <17 GPIO_ACTIVE_HIGH>; /* SODIMM 102 */
+		output-high;
+	};
+};
+
+/* Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 */
+&i2c4 {
+	status = "okay";
+};
+
+/* Colibri PWM<A> */
+&pwm1 {
+	status = "okay";
+};
+
+/* Colibri PWM<B> */
+&pwm2 {
+	status = "okay";
+};
+
+/* Colibri PWM<C> */
+&pwm3 {
+	status = "okay";
+};
+
+/* Colibri PWM<D> */
+&pwm4 {
+	status = "okay";
+};
+
+/* M41T0M6 real time clock */
+&rtc {
+	status = "okay";
+};
+
+/* Colibri UART_A */
+&uart1 {
+	status = "okay";
+};
+
+/* Colibri UART_B */
+&uart2 {
+	status = "okay";
+};
+
+/* Colibri UART_C */
+&uart3 {
+	status = "okay";
+};
+
+/* Colibri USBC */
+&usbotg1 {
+	disable-over-current;
+	status = "okay";
+};
+
+/* Colibri MMC/SD, UHS-I capable uSD slot */
+&usdhc1 {
+	cap-power-off-card;
+	/delete-property/ keep-power-in-suspend;
+	/delete-property/ no-1-8-v;
+	vmmc-supply = <&reg_3v3_vmmc>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7-colibri-iris.dtsi b/arch/arm/boot/dts/nxp/imx/imx7-colibri-iris.dtsi
new file mode 100644
index 000000000000..6a9e5ab59691
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7-colibri-iris.dtsi
@@ -0,0 +1,109 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/* Colibri AD0 to AD3 */
+&adc1 {
+	status = "okay";
+};
+
+/*
+ * The Atmel maxtouch controller uses SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2, pwm3.
+ * So if you enable following capacitive touch controller, disable pwm2/pwm3 first.
+ */
+&atmel_mxt_ts {
+	interrupt-parent = <&gpio1>;
+	interrupts = <9 IRQ_TYPE_EDGE_FALLING>;		/* SODIMM 28 / INT */
+	pinctrl-0 = <&pinctrl_atmel_adapter>;
+	reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;	/* SODIMM 30 / RST */
+};
+
+/* Colibri SSP */
+&ecspi3 {
+	status = "okay";
+};
+
+/* Colibri Fast Ethernet */
+&fec1 {
+	status = "okay";
+};
+
+&gpio2 {
+	/*
+	 * uart25 turns the UART transceiver for UART2 and 5 on. If one wants to turn the
+	 * transceiver off, that property has to be deleted and the gpio handled in userspace.
+	 * The same applies to uart1_tx_on where the UART1 transceiver is turned on.
+	 */
+	uart25-tx-on-hog {
+		gpio-hog;
+		gpios = <27 GPIO_ACTIVE_HIGH>; /* SODIMM 104 */
+		output-high;
+	};
+};
+
+&gpio5 {
+	uart1-tx-on-hog {
+		gpio-hog;
+		gpios = <17 GPIO_ACTIVE_HIGH>; /* SODIMM 102 */
+		output-high;
+	};
+};
+
+/* Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 */
+&i2c4 {
+	status = "okay";
+};
+
+/* Colibri PWM<A> */
+&pwm1 {
+	status = "okay";
+};
+
+/* Colibri PWM<B> */
+&pwm2 {
+	/* The pwm2 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri PWM<C> */
+&pwm3 {
+	/* The pwm3 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri PWM<D> */
+&pwm4 {
+	status = "okay";
+};
+
+/* M41T0M6 real time clock */
+&rtc {
+	status = "okay";
+};
+
+/* Colibri UART_A */
+&uart1 {
+	status = "okay";
+};
+
+/* Colibri UART_B */
+&uart2 {
+	status = "okay";
+};
+
+/* Colibri UART_C */
+&uart3 {
+	status = "okay";
+};
+
+/* Colibri USBC */
+&usbotg1 {
+	disable-over-current;
+	status = "okay";
+};
+
+/* Colibri MMC/SD */
+&usdhc1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx7-colibri.dtsi b/arch/arm/boot/dts/nxp/imx/imx7-colibri.dtsi
index f1c60b0cb143..8666dcd7fe97 100644
--- a/arch/arm/boot/dts/imx7-colibri.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx7-colibri.dtsi
@@ -1,96 +1,197 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2016-2020 Toradex
+ * Copyright 2016-2022 Toradex
  */
 
+#include <dt-bindings/pwm/pwm.h>
+
 / {
-	bl: backlight {
+	aliases {
+		rtc0 = &rtc;
+		rtc1 = &snvs_rtc;
+	};
+
+	backlight: backlight {
+		brightness-levels = <0 45 63 88 119 158 203 255>;
 		compatible = "pwm-backlight";
+		default-brightness-level = <4>;
+		enable-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_bl_on>;
-		pwms = <&pwm1 0 5000000 0>;
-		enable-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+		power-supply = <&reg_module_3v3>;
+		pwms = <&pwm1 0 6666667 PWM_POLARITY_INVERTED>;
+		status = "disabled";
 	};
 
-	reg_module_3v3: regulator-module-3v3 {
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	extcon_usbc_det: usbc-det {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpios = <&gpio7 14 GPIO_ACTIVE_HIGH>; /* SODIMM 137 / USBC_DET */
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbc_det>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpiokeys>;
+
+		key-wakeup {
+			debounce-interval = <10>;
+			gpios = <&gpio1 1 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* SODIMM 45 */
+			label = "Wake-Up";
+			linux,code = <KEY_WAKEUP>;
+			wakeup-source;
+		};
+	};
+
+	panel_dpi: panel-dpi {
+		backlight = <&backlight>;
+		compatible = "edt,et057090dhu";
+		power-supply = <&reg_3v3>;
+		status = "disabled";
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcdif_out>;
+			};
+		};
+	};
+
+	reg_3v3: regulator-3v3 {
 		compatible = "regulator-fixed";
-		regulator-name = "+V3.3";
-		regulator-min-microvolt = <3300000>;
+		regulator-always-on;
 		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "3.3V";
+	};
+
+	reg_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
 		regulator-always-on;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "5V";
+	};
+
+	reg_module_3v3: regulator-module-3v3 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "+V3.3";
 	};
 
 	reg_module_3v3_avdd: regulator-module-3v3-avdd {
 		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
 		regulator-name = "+V3.3_AVDD_AUDIO";
+	};
+
+	reg_module_3v3_eth: regulator-module-3v3-eth {
+		compatible = "regulator-fixed";
+		off-on-delay-us = <200000>;
+		regulator-name = "+V3.3_ETH";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
+		regulator-boot-on;
+		startup-delay-us = <200000>;
+		vin-supply = <&reg_LDO1>;
+	};
+
+	reg_usbh_vbus: regulator-usbh-vbus {
+		compatible = "regulator-fixed";
+		gpio = <&gpio4 7 GPIO_ACTIVE_LOW>; /* SODIMM 129 / USBH_PEN */
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh_reg>;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "VCC_USB[1-4]";
+		vin-supply = <&reg_5v0>;
 	};
 
 	sound {
 		compatible = "simple-audio-card";
-		simple-audio-card,name = "imx7-sgtl5000";
-		simple-audio-card,format = "i2s";
 		simple-audio-card,bitclock-master = <&dailink_master>;
+		simple-audio-card,format = "i2s";
 		simple-audio-card,frame-master = <&dailink_master>;
+		simple-audio-card,name = "colibri-imx7";
+
 		simple-audio-card,cpu {
 			sound-dai = <&sai1>;
 		};
 
 		dailink_master: simple-audio-card,codec {
-			sound-dai = <&codec>;
 			clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
+			sound-dai = <&codec>;
 		};
 	};
 };
 
+/* Colibri AD0 to AD3 */
 &adc1 {
 	vref-supply = <&reg_DCDC3>;
 };
 
-&adc2 {
-	vref-supply = <&reg_DCDC3>;
-};
+/* ADC2 is not available as it conflicts with AD7879 resistive touchscreen. */
 
 &cpu0 {
 	cpu-supply = <&reg_DCDC2>;
 };
 
+/* Colibri SSP */
 &ecspi3 {
+	cs-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>; /* SODIMM 86 / SSPFRM */
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3_cs>;
-	cs-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
 };
 
+/* Colibri Fast Ethernet */
 &fec1 {
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&pinctrl_enet1>;
-	pinctrl-1 = <&pinctrl_enet1_sleep>;
-	clocks = <&clks IMX7D_ENET_AXI_ROOT_CLK>,
-		<&clks IMX7D_ENET_AXI_ROOT_CLK>,
-		<&clks IMX7D_ENET1_TIME_ROOT_CLK>,
-		<&clks IMX7D_PLL_ENET_MAIN_50M_CLK>;
-	clock-names = "ipg", "ahb", "ptp", "enet_clk_ref";
-	assigned-clocks = <&clks IMX7D_ENET1_TIME_ROOT_SRC>,
-			  <&clks IMX7D_ENET1_TIME_ROOT_CLK>;
 	assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
 	assigned-clock-rates = <0>, <100000000>;
-	phy-mode = "rmii";
-	phy-supply = <&reg_LDO1>;
+	assigned-clocks = <&clks IMX7D_ENET1_TIME_ROOT_SRC>,
+			  <&clks IMX7D_ENET1_TIME_ROOT_CLK>;
+	clock-names = "ipg", "ahb", "ptp", "enet_clk_ref";
+	clocks = <&clks IMX7D_ENET_AXI_ROOT_CLK>,
+		 <&clks IMX7D_ENET_AXI_ROOT_CLK>,
+		 <&clks IMX7D_ENET1_TIME_ROOT_CLK>,
+		 <&clks IMX7D_PLL_ENET_MAIN_50M_CLK>;
 	fsl,magic-packet;
+	phy-handle = <&ethphy0>;
+	phy-mode = "rmii";
+	phy-supply = <&reg_module_3v3_eth>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_enet1>;
+	pinctrl-1 = <&pinctrl_enet1_sleep>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Micrel KSZ8041RNL */
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			max-speed = <100>;
+			micrel,led-mode = <0>;
+			reg = <0>;
+		};
+	};
 };
 
 &flexcan1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_flexcan1>;
-	status = "disabled";
 };
 
 &flexcan2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_flexcan2>;
-	status = "disabled";
 };
 
 &gpio1 {
@@ -271,14 +372,16 @@
 			  "SODIMM_137";
 };
 
+/* NAND on such SKUs */
 &gpmi {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_gpmi_nand>;
 	fsl,use-minimum-ecc;
-	nand-on-flash-bbt;
 	nand-ecc-mode = "hw";
+	nand-on-flash-bbt;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
 };
 
+/* On-module Power I2C */
 &i2c1 {
 	clock-frequency = <100000>;
 	pinctrl-names = "default", "gpio";
@@ -286,33 +389,33 @@
 	pinctrl-1 = <&pinctrl_i2c1_recovery &pinctrl_i2c1_int>;
 	scl-gpios = <&gpio1 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	sda-gpios = <&gpio1 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-
 	status = "okay";
 
 	codec: sgtl5000@a {
-		compatible = "fsl,sgtl5000";
 		#sound-dai-cells = <0>;
-		reg = <0x0a>;
 		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
+		compatible = "fsl,sgtl5000";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_sai1_mclk>;
+		reg = <0xa>;
 		VDDA-supply = <&reg_module_3v3_avdd>;
-		VDDIO-supply = <&reg_module_3v3>;
 		VDDD-supply = <&reg_DCDC3>;
+		VDDIO-supply = <&reg_module_3v3>;
 	};
 
-	ad7879@2c {
+	ad7879_ts: touchscreen@2c {
+		adi,acquisition-time = /bits/ 8 <1>;
+		adi,averaging = /bits/ 8 <1>;
+		adi,conversion-interval = /bits/ 8 <255>;
+		adi,first-conversion-delay = /bits/ 8 <3>;
+		adi,median-filter-size = /bits/ 8 <2>;
+		adi,resistance-plate-x = <120>;
 		compatible = "adi,ad7879-1";
-		reg = <0x2c>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
+		reg = <0x2c>;
 		touchscreen-max-pressure = <4096>;
-		adi,resistance-plate-x = <120>;
-		adi,first-conversion-delay = /bits/ 8 <3>;
-		adi,acquisition-time = /bits/ 8 <1>;
-		adi,median-filter-size = /bits/ 8 <2>;
-		adi,averaging = /bits/ 8 <1>;
-		adi,conversion-interval = /bits/ 8 <255>;
+		status = "disabled";
 	};
 
 	pmic@33 {
@@ -320,71 +423,81 @@
 		reg = <0x33>;
 
 		regulators {
-			reg_DCDC1: DCDC1 {  /* V1.0_SOC */
-				regulator-min-microvolt = <1000000>;
-				regulator-max-microvolt = <1100000>;
-				regulator-boot-on;
+			reg_DCDC1: DCDC1 {
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1100000>;
+				regulator-min-microvolt = <1000000>;
+				regulator-name = "+V1.0_SOC";
 			};
 
-			reg_DCDC2: DCDC2 { /* V1.1_ARM */
-				regulator-min-microvolt = <975000>;
-				regulator-max-microvolt = <1100000>;
-				regulator-boot-on;
+			reg_DCDC2: DCDC2 {
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1100000>;
+				regulator-min-microvolt = <975000>;
+				regulator-name = "+V1.1_ARM";
 			};
 
-			reg_DCDC3: DCDC3 { /* V1.8 */
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-boot-on;
+			reg_DCDC3: DCDC3 {
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "+V1.8";
 			};
 
-			reg_DCDC4: DCDC4 { /* V1.35_DRAM */
-				regulator-min-microvolt = <1350000>;
-				regulator-max-microvolt = <1350000>;
-				regulator-boot-on;
+			reg_DCDC4: DCDC4 {
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1350000>;
+				regulator-min-microvolt = <1350000>;
+				regulator-name = "+V1.35_DRAM";
 			};
 
-			reg_LDO1: LDO1 { /* PWR_EN_+V3.3_ETH */
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
+			reg_LDO1: LDO1 {
 				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-name = "PWR_EN_+V3.3_ETH";
 			};
 
-			reg_LDO2: LDO2 { /* +V1.8_SD */
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
+			reg_LDO2: LDO2 {
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "+V1.8_SD";
 			};
 
-			reg_LDO3: LDO3 { /* PWR_EN_+V3.3_LPSR */
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
+			reg_LDO3: LDO3 {
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-name = "PWR_EN_+V3.3_LPSR";
 			};
 
-			reg_LDO4: LDO4 { /* V1.8_LPSR */
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-boot-on;
+			reg_LDO4: LDO4 {
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "+V1.8_LPSR";
 			};
 
-			reg_LDO5: LDO5 { /* PWR_EN_+V3.3 */
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
+			reg_LDO5: LDO5 {
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-name = "PWR_EN_+V3.3";
 			};
 		};
 	};
 };
 
+/* Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 */
 &i2c4 {
 	clock-frequency = <100000>;
 	pinctrl-names = "default", "gpio";
@@ -392,36 +505,69 @@
 	pinctrl-1 = <&pinctrl_i2c4_recovery>;
 	scl-gpios = <&gpio7 8 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	sda-gpios = <&gpio7 9 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "disabled";
+
+	/* Atmel maxtouch controller */
+	atmel_mxt_ts: touchscreen@4a {
+		compatible = "atmel,maxtouch";
+		interrupt-parent = <&gpio2>;
+		interrupts = <15 IRQ_TYPE_EDGE_FALLING>;        /* SODIMM 107 / INT */
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_atmel_connector>;
+		reg = <0x4a>;
+		reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;      /* SODIMM 106 / RST */
+		status = "disabled";
+	};
+
+	/* M41T0M6 real time clock on carrier board */
+	rtc: rtc@68 {
+		compatible = "st,m41t0";
+		reg = <0x68>;
+		status = "disabled";
+	};
 };
 
 &lcdif {
+	assigned-clocks = <&clks IMX7D_LCDIF_PIXEL_ROOT_SRC>;
+	assigned-clock-parents = <&clks IMX7D_PLL_VIDEO_POST_DIV>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_lcdif_dat
 		     &pinctrl_lcdif_ctrl>;
+	status = "disabled";
+
+	port {
+		lcdif_out: endpoint {
+			remote-endpoint = <&lcd_panel_in>;
+		};
+	};
 };
 
+/* Colibri PWM<A> */
 &pwm1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 };
 
+/* Colibri PWM<B> */
 &pwm2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm2>;
 };
 
+/* Colibri PWM<C> */
 &pwm3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 };
 
+/* Colibri PWM<D> */
 &pwm4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 };
 
 &reg_1p0d {
-	vin-supply = <&reg_DCDC3>;
+	vin-supply = <&reg_DCDC3>; /* VDDA_1P8_IN */
 };
 
 &sai1 {
@@ -430,237 +576,257 @@
 	status = "okay";
 };
 
+/* Colibri UART_A */
 &uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1 &pinctrl_uart1_ctrl1 &pinctrl_uart1_ctrl2>;
 	assigned-clocks = <&clks IMX7D_UART1_ROOT_SRC>;
 	assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>;
-	uart-has-rtscts;
 	fsl,dte-mode;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1 &pinctrl_uart1_ctrl1 &pinctrl_uart1_ctrl2>;
+	uart-has-rtscts;
 };
 
+/* Colibri UART_B */
 &uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
 	assigned-clocks = <&clks IMX7D_UART2_ROOT_SRC>;
 	assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>;
-	uart-has-rtscts;
 	fsl,dte-mode;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	uart-has-rtscts;
 };
 
+/* Colibri UART_C */
 &uart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart3>;
 	assigned-clocks = <&clks IMX7D_UART3_ROOT_SRC>;
 	assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>;
 	fsl,dte-mode;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
 };
 
+/* Colibri USBC */
 &usbotg1 {
-	dr_mode = "host";
+	dr_mode = "otg";
+	extcon = <0>, <&extcon_usbc_det>;
 };
 
+/* Colibri MMC/SD */
 &usdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_cd_usdhc1>;
 	cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
 	disable-wp;
+	no-1-8-v;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_cd_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz &pinctrl_cd_usdhc1>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz &pinctrl_cd_usdhc1>;
+	pinctrl-3 = <&pinctrl_usdhc1_sleep &pinctrl_cd_usdhc1_sleep>;
+	vmmc-supply = <&reg_3v3>;
 	vqmmc-supply = <&reg_LDO2>;
+	wakeup-source;
 };
 
+/* eMMC on 1GB (eMMC) SKUs */
 &usdhc3 {
-	pinctrl-names = "default", "state_100mhz", "state_200mhz";
-	pinctrl-0 = <&pinctrl_usdhc3>;
-	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
-	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
 	assigned-clocks = <&clks IMX7D_USDHC3_ROOT_CLK>;
 	assigned-clock-rates = <400000000>;
 	bus-width = <8>;
 	fsl,tuning-step = <2>;
-	vmmc-supply = <&reg_module_3v3>;
-	vqmmc-supply = <&reg_DCDC3>;
 	non-removable;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
 	sdhci-caps-mask = <0x80000000 0x0>;
+	vmmc-supply = <&reg_module_3v3>;
+	vqmmc-supply = <&reg_DCDC3>;
 };
 
 &iomuxc {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_gpio1 &pinctrl_gpio2 &pinctrl_gpio3 &pinctrl_gpio4
-		     &pinctrl_gpio7 &pinctrl_usbc_det>;
-
-	pinctrl_gpio1: gpio1-grp {
-		fsl,pins = <
-			MX7D_PAD_SAI1_RX_SYNC__GPIO6_IO16	0x14 /* SODIMM 77 */
-			MX7D_PAD_EPDC_DATA09__GPIO2_IO9		0x14 /* SODIMM 89 */
-			MX7D_PAD_EPDC_DATA08__GPIO2_IO8		0x74 /* SODIMM 91 */
-			MX7D_PAD_LCD_RESET__GPIO3_IO4		0x14 /* SODIMM 93 */
-			MX7D_PAD_EPDC_DATA13__GPIO2_IO13	0x14 /* SODIMM 95 */
-			MX7D_PAD_ENET1_RGMII_TXC__GPIO7_IO11	0x14 /* SODIMM 99 */
-			MX7D_PAD_EPDC_DATA10__GPIO2_IO10	0x74 /* SODIMM 105 */
-			MX7D_PAD_EPDC_DATA00__GPIO2_IO0		0x14 /* SODIMM 111 */
-			MX7D_PAD_EPDC_DATA01__GPIO2_IO1		0x14 /* SODIMM 113 */
-			MX7D_PAD_EPDC_DATA02__GPIO2_IO2		0x14 /* SODIMM 115 */
-			MX7D_PAD_EPDC_DATA03__GPIO2_IO3		0x14 /* SODIMM 117 */
-			MX7D_PAD_EPDC_DATA04__GPIO2_IO4		0x14 /* SODIMM 119 */
-			MX7D_PAD_EPDC_DATA05__GPIO2_IO5		0x14 /* SODIMM 121 */
-			MX7D_PAD_EPDC_DATA06__GPIO2_IO6		0x14 /* SODIMM 123 */
-			MX7D_PAD_EPDC_DATA07__GPIO2_IO7		0x14 /* SODIMM 125 */
-			MX7D_PAD_EPDC_SDCE2__GPIO2_IO22		0x14 /* SODIMM 127 */
-			MX7D_PAD_UART3_RTS_B__GPIO4_IO6		0x14 /* SODIMM 131 */
-			MX7D_PAD_EPDC_GDRL__GPIO2_IO26		0x14 /* SODIMM 133 */
-			MX7D_PAD_SAI1_RX_DATA__GPIO6_IO12	0x14 /* SODIMM 169 */
-			MX7D_PAD_SAI1_RX_BCLK__GPIO6_IO17	0x14 /* SODIMM 24 */
-			MX7D_PAD_SD2_DATA2__GPIO5_IO16		0x14 /* SODIMM 100 */
-			MX7D_PAD_SD2_DATA3__GPIO5_IO17		0x14 /* SODIMM 102 */
-			MX7D_PAD_EPDC_GDSP__GPIO2_IO27		0x14 /* SODIMM 104 */
-			MX7D_PAD_EPDC_BDR1__GPIO2_IO29		0x14 /* SODIMM 110 */
-			MX7D_PAD_EPDC_PWR_COM__GPIO2_IO30	0x14 /* SODIMM 112 */
-			MX7D_PAD_EPDC_SDCLK__GPIO2_IO16		0x14 /* SODIMM 114 */
-			MX7D_PAD_EPDC_SDLE__GPIO2_IO17		0x14 /* SODIMM 116 */
-			MX7D_PAD_EPDC_SDOE__GPIO2_IO18		0x14 /* SODIMM 118 */
-			MX7D_PAD_EPDC_SDSHR__GPIO2_IO19		0x14 /* SODIMM 120 */
-			MX7D_PAD_EPDC_SDCE0__GPIO2_IO20		0x14 /* SODIMM 122 */
-			MX7D_PAD_EPDC_SDCE1__GPIO2_IO21		0x14 /* SODIMM 124 */
-			MX7D_PAD_EPDC_DATA14__GPIO2_IO14	0x14 /* SODIMM 126 */
-			MX7D_PAD_EPDC_PWR_STAT__GPIO2_IO31	0x14 /* SODIMM 128 */
-			MX7D_PAD_EPDC_SDCE3__GPIO2_IO23		0x14 /* SODIMM 130 */
-			MX7D_PAD_EPDC_GDCLK__GPIO2_IO24		0x14 /* SODIMM 132 */
-			MX7D_PAD_EPDC_GDOE__GPIO2_IO25		0x14 /* SODIMM 134 */
-			MX7D_PAD_EPDC_DATA12__GPIO2_IO12	0x14 /* SODIMM 150 */
-			MX7D_PAD_EPDC_DATA11__GPIO2_IO11	0x14 /* SODIMM 152 */
-			MX7D_PAD_SD2_CLK__GPIO5_IO12		0x14 /* SODIMM 184 */
-			MX7D_PAD_SD2_CMD__GPIO5_IO13		0x14 /* SODIMM 186 */
-		>;
-	};
-
-	pinctrl_gpio2: gpio2-grp { /* On X22 Camera interface */
-		fsl,pins = <
-			MX7D_PAD_ECSPI2_SS0__GPIO4_IO23		0x14 /* SODIMM 65 */
-			MX7D_PAD_SD1_CD_B__GPIO5_IO0		0x74 /* SODIMM 69 */
-			MX7D_PAD_I2C4_SDA__GPIO4_IO15		0x14 /* SODIMM 75 */
-			MX7D_PAD_ECSPI1_MISO__GPIO4_IO18	0x14 /* SODIMM 79 */
-			MX7D_PAD_I2C3_SCL__GPIO4_IO12		0x14 /* SODIMM 81 */
-			MX7D_PAD_ECSPI2_MISO__GPIO4_IO22	0x14 /* SODIMM 85 */
-			MX7D_PAD_ECSPI1_SS0__GPIO4_IO19		0x14 /* SODIMM 97 */
-			MX7D_PAD_ECSPI1_SCLK__GPIO4_IO16	0x14 /* SODIMM 101 */
-			MX7D_PAD_ECSPI1_MOSI__GPIO4_IO17	0x14 /* SODIMM 103 */
-			MX7D_PAD_I2C3_SDA__GPIO4_IO13		0x14 /* SODIMM 94 */
-			MX7D_PAD_I2C4_SCL__GPIO4_IO14		0x14 /* SODIMM 96 */
-			MX7D_PAD_SD2_RESET_B__GPIO5_IO11	0x14 /* SODIMM 98 */
-		>;
-	};
-
-	pinctrl_gpio3: gpio3-grp { /* LCD 18-23 */
+	pinctrl-0 = <&pinctrl_gpio1 &pinctrl_gpio2 &pinctrl_gpio3 &pinctrl_gpio4>;
+
+	/*
+	 * Atmel MXT touchsceen + Capacitive Touch Adapter
+	 * NOTE: This pin group conflicts with pin groups pinctrl_pwm2/pinctrl_pwm3.
+	 * Don't use them simultaneously.
+	 */
+	pinctrl_atmel_adapter: atmeladaptergrp {
 		fsl,pins = <
-			MX7D_PAD_LCD_DATA18__GPIO3_IO23		0x14 /* SODIMM 136 */
-			MX7D_PAD_LCD_DATA19__GPIO3_IO24		0x14 /* SODIMM 138 */
-			MX7D_PAD_LCD_DATA20__GPIO3_IO25		0x14 /* SODIMM 140 */
-			MX7D_PAD_LCD_DATA21__GPIO3_IO26		0x14 /* SODIMM 142 */
-			MX7D_PAD_LCD_DATA22__GPIO3_IO27		0x74 /* SODIMM 144 */
-			MX7D_PAD_LCD_DATA23__GPIO3_IO28		0x74 /* SODIMM 146 */
+			MX7D_PAD_GPIO1_IO09__GPIO1_IO9		0x74 /* SODIMM 28 / INT */
+			MX7D_PAD_GPIO1_IO10__GPIO1_IO10		0x14 /* SODIMM 30 / RST */
 		>;
 	};
 
-	pinctrl_gpio4: gpio4-grp { /* Alternatively CAN2 */
+	/* Atmel MXT touchsceen + boards with built-in Capacitive Touch Connector */
+	pinctrl_atmel_connector: atmelconnectorgrp {
 		fsl,pins = <
-			MX7D_PAD_GPIO1_IO15__GPIO1_IO15		0x14 /* SODIMM 178 */
-			MX7D_PAD_GPIO1_IO14__GPIO1_IO14		0x14 /* SODIMM 188 */
+			MX7D_PAD_EPDC_BDR0__GPIO2_IO28		0x14 /* SODIMM 106 / RST */
+			MX7D_PAD_EPDC_DATA15__GPIO2_IO15	0x74 /* SODIMM 107 / INT */
 		>;
 	};
 
-	pinctrl_gpio7: gpio7-grp { /* Alternatively CAN1 */
+	pinctrl_can_int: canintgrp {
 		fsl,pins = <
-			MX7D_PAD_ENET1_RGMII_RD3__GPIO7_IO3	0x14 /* SODIMM 55 */
-			MX7D_PAD_ENET1_RGMII_RD2__GPIO7_IO2	0x14 /* SODIMM 63 */
+			MX7D_PAD_SD1_RESET_B__GPIO5_IO2		0X14 /* SODIMM 73 */
 		>;
 	};
 
-	pinctrl_i2c1_int: i2c1-int-grp { /* PMIC / TOUCH */
+	pinctrl_ecspi3: ecspi3grp {
 		fsl,pins = <
-			MX7D_PAD_GPIO1_IO13__GPIO1_IO13	0x79
+			MX7D_PAD_I2C1_SCL__ECSPI3_MISO		0x2 /* SODIMM 90 */
+			MX7D_PAD_I2C1_SDA__ECSPI3_MOSI		0x2 /* SODIMM 92 */
+			MX7D_PAD_I2C2_SCL__ECSPI3_SCLK		0x2 /* SODIMM 88 */
 		>;
 	};
 
-	pinctrl_can_int: can-int-grp {
+	pinctrl_ecspi3_cs: ecspi3csgrp {
 		fsl,pins = <
-			MX7D_PAD_SD1_RESET_B__GPIO5_IO2		0X14 /* SODIMM 73 */
+			MX7D_PAD_I2C2_SDA__GPIO4_IO11		0x14 /* SODIMM 86 */
 		>;
 	};
 
 	pinctrl_enet1: enet1grp {
 		fsl,pins = <
-			MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL	0x73
 			MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0	0x73
 			MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1	0x73
 			MX7D_PAD_ENET1_RGMII_RXC__ENET1_RX_ER		0x73
-
-			MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL	0x73
+			MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL	0x73
 			MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0	0x73
 			MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1	0x73
+			MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL	0x73
 			MX7D_PAD_GPIO1_IO12__CCM_ENET_REF_CLK1		0x73
 			MX7D_PAD_SD2_CD_B__ENET1_MDIO			0x3
 			MX7D_PAD_SD2_WP__ENET1_MDC			0x3
 		>;
 	};
 
-	pinctrl_enet1_sleep: enet1sleepgrp {
+	pinctrl_enet1_sleep: enet1-sleepgrp {
 		fsl,pins = <
-			MX7D_PAD_ENET1_RGMII_RX_CTL__GPIO7_IO4		0x0
 			MX7D_PAD_ENET1_RGMII_RD0__GPIO7_IO0		0x0
 			MX7D_PAD_ENET1_RGMII_RD1__GPIO7_IO1		0x0
 			MX7D_PAD_ENET1_RGMII_RXC__GPIO7_IO5		0x0
-
-			MX7D_PAD_ENET1_RGMII_TX_CTL__GPIO7_IO10		0x0
+			MX7D_PAD_ENET1_RGMII_RX_CTL__GPIO7_IO4		0x0
 			MX7D_PAD_ENET1_RGMII_TD0__GPIO7_IO6		0x0
 			MX7D_PAD_ENET1_RGMII_TD1__GPIO7_IO7		0x0
+			MX7D_PAD_ENET1_RGMII_TX_CTL__GPIO7_IO10		0x0
 			MX7D_PAD_GPIO1_IO12__GPIO1_IO12			0x0
 			MX7D_PAD_SD2_CD_B__GPIO5_IO9			0x0
 			MX7D_PAD_SD2_WP__GPIO5_IO10			0x0
 		>;
 	};
 
-	pinctrl_ecspi3_cs: ecspi3-cs-grp {
+	pinctrl_flexcan1: flexcan1grp {
 		fsl,pins = <
-			MX7D_PAD_I2C2_SDA__GPIO4_IO11		0x14
+			MX7D_PAD_ENET1_RGMII_RD2__FLEXCAN1_RX	0x79 /* SODIMM 63 */
+			MX7D_PAD_ENET1_RGMII_RD3__FLEXCAN1_TX	0x79 /* SODIMM 55 */
 		>;
 	};
 
-	pinctrl_ecspi3: ecspi3-grp {
+	pinctrl_flexcan2: flexcan2grp {
 		fsl,pins = <
-			MX7D_PAD_I2C1_SCL__ECSPI3_MISO		0x2
-			MX7D_PAD_I2C1_SDA__ECSPI3_MOSI		0x2
-			MX7D_PAD_I2C2_SCL__ECSPI3_SCLK		0x2
+			MX7D_PAD_GPIO1_IO14__FLEXCAN2_RX	0x79 /* SODIMM 188 */
+			MX7D_PAD_GPIO1_IO15__FLEXCAN2_TX	0x79 /* SODIMM 178 */
 		>;
 	};
 
-	pinctrl_flexcan1: flexcan1-grp {
+	pinctrl_gpio1: gpio1grp {
 		fsl,pins = <
-			MX7D_PAD_ENET1_RGMII_RD3__FLEXCAN1_TX	0x79 /* SODIMM 55 */
-			MX7D_PAD_ENET1_RGMII_RD2__FLEXCAN1_RX	0x79 /* SODIMM 63 */
+			MX7D_PAD_EPDC_BDR1__GPIO2_IO29		0x14 /* SODIMM 110 */
+			MX7D_PAD_EPDC_DATA00__GPIO2_IO0		0x14 /* SODIMM 111 */
+			MX7D_PAD_EPDC_DATA01__GPIO2_IO1		0x14 /* SODIMM 113 */
+			MX7D_PAD_EPDC_DATA02__GPIO2_IO2		0x14 /* SODIMM 115 */
+			MX7D_PAD_EPDC_DATA03__GPIO2_IO3		0x14 /* SODIMM 117 */
+			MX7D_PAD_EPDC_DATA04__GPIO2_IO4		0x14 /* SODIMM 119 */
+			MX7D_PAD_EPDC_DATA05__GPIO2_IO5		0x14 /* SODIMM 121 */
+			MX7D_PAD_EPDC_DATA06__GPIO2_IO6		0x14 /* SODIMM 123 */
+			MX7D_PAD_EPDC_DATA07__GPIO2_IO7		0x14 /* SODIMM 125 */
+			MX7D_PAD_EPDC_DATA08__GPIO2_IO8		0x74 /* SODIMM 91 */
+			MX7D_PAD_EPDC_DATA09__GPIO2_IO9		0x14 /* SODIMM 89 */
+			MX7D_PAD_EPDC_DATA10__GPIO2_IO10	0x74 /* SODIMM 105 */
+			MX7D_PAD_EPDC_DATA11__GPIO2_IO11	0x14 /* SODIMM 152 */
+			MX7D_PAD_EPDC_DATA12__GPIO2_IO12	0x14 /* SODIMM 150 */
+			MX7D_PAD_EPDC_DATA14__GPIO2_IO14	0x14 /* SODIMM 126 */
+			MX7D_PAD_EPDC_GDCLK__GPIO2_IO24		0x14 /* SODIMM 132 */
+			MX7D_PAD_EPDC_GDOE__GPIO2_IO25		0x14 /* SODIMM 134 */
+			MX7D_PAD_EPDC_GDRL__GPIO2_IO26		0x14 /* SODIMM 133 */
+			MX7D_PAD_EPDC_GDSP__GPIO2_IO27		0x14 /* SODIMM 104 */
+			MX7D_PAD_EPDC_PWR_COM__GPIO2_IO30	0x14 /* SODIMM 112 */
+			MX7D_PAD_EPDC_PWR_STAT__GPIO2_IO31	0x14 /* SODIMM 128 */
+			MX7D_PAD_EPDC_SDCE0__GPIO2_IO20		0x14 /* SODIMM 122 */
+			MX7D_PAD_EPDC_SDCE1__GPIO2_IO21		0x14 /* SODIMM 124 */
+			MX7D_PAD_EPDC_SDCE2__GPIO2_IO22		0x14 /* SODIMM 127 */
+			MX7D_PAD_EPDC_SDCE3__GPIO2_IO23		0x14 /* SODIMM 130 */
+			MX7D_PAD_EPDC_SDCLK__GPIO2_IO16		0x14 /* SODIMM 114 */
+			MX7D_PAD_EPDC_SDLE__GPIO2_IO17		0x14 /* SODIMM 116 */
+			MX7D_PAD_EPDC_SDOE__GPIO2_IO18		0x14 /* SODIMM 118 */
+			MX7D_PAD_EPDC_SDSHR__GPIO2_IO19		0x14 /* SODIMM 120 */
+			MX7D_PAD_LCD_RESET__GPIO3_IO4		0x14 /* SODIMM 93 */
+			MX7D_PAD_SAI1_RX_BCLK__GPIO6_IO17	0x14 /* SODIMM 24 */
+			MX7D_PAD_SAI1_RX_DATA__GPIO6_IO12	0x14 /* SODIMM 169 */
+			MX7D_PAD_SAI1_RX_SYNC__GPIO6_IO16	0x14 /* SODIMM 77 */
+			MX7D_PAD_SD2_CLK__GPIO5_IO12		0x14 /* SODIMM 184 */
+			MX7D_PAD_SD2_CMD__GPIO5_IO13		0x14 /* SODIMM 186 */
+			MX7D_PAD_SD2_DATA2__GPIO5_IO16		0x14 /* SODIMM 100 */
+			MX7D_PAD_SD2_DATA3__GPIO5_IO17		0x14 /* SODIMM 102 */
+			MX7D_PAD_UART3_RTS_B__GPIO4_IO6		0x14 /* SODIMM 131 */
 		>;
 	};
 
-	pinctrl_flexcan2: flexcan2-grp {
+	pinctrl_gpio2: gpio2grp { /* On X22 Camera interface */
 		fsl,pins = <
-			MX7D_PAD_GPIO1_IO14__FLEXCAN2_RX	0x79 /* SODIMM 188 */
-			MX7D_PAD_GPIO1_IO15__FLEXCAN2_TX	0x79 /* SODIMM 178 */
+			MX7D_PAD_ECSPI1_MISO__GPIO4_IO18	0x14 /* SODIMM 79 */
+			MX7D_PAD_ECSPI1_MOSI__GPIO4_IO17	0x14 /* SODIMM 103 */
+			MX7D_PAD_ECSPI1_SCLK__GPIO4_IO16	0x14 /* SODIMM 101 */
+			MX7D_PAD_ECSPI1_SS0__GPIO4_IO19		0x14 /* SODIMM 97 */
+			MX7D_PAD_ECSPI2_MISO__GPIO4_IO22	0x14 /* SODIMM 85 */
+			MX7D_PAD_ECSPI2_SS0__GPIO4_IO23		0x14 /* SODIMM 65 */
+			MX7D_PAD_I2C3_SCL__GPIO4_IO12		0x14 /* SODIMM 81 */
+			MX7D_PAD_I2C3_SDA__GPIO4_IO13		0x14 /* SODIMM 94 */
+			MX7D_PAD_I2C4_SCL__GPIO4_IO14		0x14 /* SODIMM 96 */
+			MX7D_PAD_I2C4_SDA__GPIO4_IO15		0x14 /* SODIMM 75 */
+			MX7D_PAD_SD1_CD_B__GPIO5_IO0		0x74 /* SODIMM 69 */
+			MX7D_PAD_SD2_RESET_B__GPIO5_IO11	0x14 /* SODIMM 98 */
+		>;
+	};
+
+	pinctrl_gpio3: gpio3grp { /* LCD 18-23 */
+		fsl,pins = <
+			MX7D_PAD_LCD_DATA18__GPIO3_IO23		0x14 /* SODIMM 136 */
+			MX7D_PAD_LCD_DATA19__GPIO3_IO24		0x14 /* SODIMM 138 */
+			MX7D_PAD_LCD_DATA20__GPIO3_IO25		0x14 /* SODIMM 140 */
+			MX7D_PAD_LCD_DATA21__GPIO3_IO26		0x14 /* SODIMM 142 */
+			MX7D_PAD_LCD_DATA22__GPIO3_IO27		0x74 /* SODIMM 144 */
+			MX7D_PAD_LCD_DATA23__GPIO3_IO28		0x74 /* SODIMM 146 */
+		>;
+	};
+
+	pinctrl_gpio4: gpio4grp { /* Alternatively CAN2 */
+		fsl,pins = <
+			MX7D_PAD_GPIO1_IO14__GPIO1_IO14		0x14 /* SODIMM 188 */
+			MX7D_PAD_GPIO1_IO15__GPIO1_IO15		0x14 /* SODIMM 178 */
+		>;
+	};
+
+	pinctrl_gpio7: gpio7grp { /* Alternatively CAN1 */
+		fsl,pins = <
+			MX7D_PAD_ENET1_RGMII_RD2__GPIO7_IO2	0x14 /* SODIMM 63 */
+			MX7D_PAD_ENET1_RGMII_RD3__GPIO7_IO3	0x14 /* SODIMM 55 */
 		>;
 	};
 
-	pinctrl_gpio_bl_on: gpio-bl-on {
+	pinctrl_gpio_bl_on: gpioblongrp {
 		fsl,pins = <
 			MX7D_PAD_SD1_WP__GPIO5_IO1		0x14 /* SODIMM 71 */
 		>;
 	};
 
-	pinctrl_gpmi_nand: gpmi-nand-grp {
+	pinctrl_gpmi_nand: gpminandgrp {
 		fsl,pins = <
-			MX7D_PAD_SD3_CLK__NAND_CLE		0x71
-			MX7D_PAD_SD3_CMD__NAND_ALE		0x71
 			MX7D_PAD_SAI1_TX_BCLK__NAND_CE0_B	0x71
 			MX7D_PAD_SAI1_TX_DATA__NAND_READY_B	0x74
-			MX7D_PAD_SD3_STROBE__NAND_RE_B		0x71
-			MX7D_PAD_SD3_RESET_B__NAND_WE_B		0x71
+			MX7D_PAD_SD3_CLK__NAND_CLE		0x71
+			MX7D_PAD_SD3_CMD__NAND_ALE		0x71
 			MX7D_PAD_SD3_DATA0__NAND_DATA00		0x71
 			MX7D_PAD_SD3_DATA1__NAND_DATA01		0x71
 			MX7D_PAD_SD3_DATA2__NAND_DATA02		0x71
@@ -669,13 +835,21 @@
 			MX7D_PAD_SD3_DATA5__NAND_DATA05		0x71
 			MX7D_PAD_SD3_DATA6__NAND_DATA06		0x71
 			MX7D_PAD_SD3_DATA7__NAND_DATA07		0x71
+			MX7D_PAD_SD3_RESET_B__NAND_WE_B		0x71
+			MX7D_PAD_SD3_STROBE__NAND_RE_B		0x71
 		>;
 	};
 
-	pinctrl_i2c4: i2c4-grp {
+	pinctrl_i2c1_int: i2c1intgrp { /* PMIC / TOUCH */
 		fsl,pins = <
-			MX7D_PAD_ENET1_RGMII_TD3__I2C4_SDA	0x4000007f
-			MX7D_PAD_ENET1_RGMII_TD2__I2C4_SCL	0x4000007f
+			MX7D_PAD_GPIO1_IO13__GPIO1_IO13	0x79
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX7D_PAD_ENET1_RGMII_TD2__I2C4_SCL	0x4000007f /* SODIMM 196 */
+			MX7D_PAD_ENET1_RGMII_TD3__I2C4_SDA	0x4000007f /* SODIMM 194 */
 		>;
 	};
 
@@ -686,155 +860,176 @@
 		>;
 	};
 
-	pinctrl_lcdif_dat: lcdif-dat-grp {
+	pinctrl_lcdif_dat: lcdifdatgrp {
+		fsl,pins = <
+			MX7D_PAD_LCD_DATA00__LCD_DATA0		0x79 /* SODIMM 76 */
+			MX7D_PAD_LCD_DATA01__LCD_DATA1		0x79 /* SODIMM 70 */
+			MX7D_PAD_LCD_DATA02__LCD_DATA2		0x79 /* SODIMM 60 */
+			MX7D_PAD_LCD_DATA03__LCD_DATA3		0x79 /* SODIMM 58 */
+			MX7D_PAD_LCD_DATA04__LCD_DATA4		0x79 /* SODIMM 78 */
+			MX7D_PAD_LCD_DATA05__LCD_DATA5		0x79 /* SODIMM 72 */
+			MX7D_PAD_LCD_DATA06__LCD_DATA6		0x79 /* SODIMM 80 */
+			MX7D_PAD_LCD_DATA07__LCD_DATA7		0x79 /* SODIMM 46 */
+			MX7D_PAD_LCD_DATA08__LCD_DATA8		0x79 /* SODIMM 62 */
+			MX7D_PAD_LCD_DATA09__LCD_DATA9		0x79 /* SODIMM 48 */
+			MX7D_PAD_LCD_DATA10__LCD_DATA10		0x79 /* SODIMM 74 */
+			MX7D_PAD_LCD_DATA11__LCD_DATA11		0x79 /* SODIMM 50 */
+			MX7D_PAD_LCD_DATA12__LCD_DATA12		0x79 /* SODIMM 52 */
+			MX7D_PAD_LCD_DATA13__LCD_DATA13		0x79 /* SODIMM 54 */
+			MX7D_PAD_LCD_DATA14__LCD_DATA14		0x79 /* SODIMM 66 */
+			MX7D_PAD_LCD_DATA15__LCD_DATA15		0x79 /* SODIMM 64 */
+			MX7D_PAD_LCD_DATA16__LCD_DATA16		0x79 /* SODIMM 57 */
+			MX7D_PAD_LCD_DATA17__LCD_DATA17		0x79 /* SODIMM 61 */
+		>;
+	};
+
+	pinctrl_lcdif_dat_24: lcdifdat24grp {
 		fsl,pins = <
-			MX7D_PAD_LCD_DATA00__LCD_DATA0		0x79
-			MX7D_PAD_LCD_DATA01__LCD_DATA1		0x79
-			MX7D_PAD_LCD_DATA02__LCD_DATA2		0x79
-			MX7D_PAD_LCD_DATA03__LCD_DATA3		0x79
-			MX7D_PAD_LCD_DATA04__LCD_DATA4		0x79
-			MX7D_PAD_LCD_DATA05__LCD_DATA5		0x79
-			MX7D_PAD_LCD_DATA06__LCD_DATA6		0x79
-			MX7D_PAD_LCD_DATA07__LCD_DATA7		0x79
-			MX7D_PAD_LCD_DATA08__LCD_DATA8		0x79
-			MX7D_PAD_LCD_DATA09__LCD_DATA9		0x79
-			MX7D_PAD_LCD_DATA10__LCD_DATA10		0x79
-			MX7D_PAD_LCD_DATA11__LCD_DATA11		0x79
-			MX7D_PAD_LCD_DATA12__LCD_DATA12		0x79
-			MX7D_PAD_LCD_DATA13__LCD_DATA13		0x79
-			MX7D_PAD_LCD_DATA14__LCD_DATA14		0x79
-			MX7D_PAD_LCD_DATA15__LCD_DATA15		0x79
-			MX7D_PAD_LCD_DATA16__LCD_DATA16		0x79
-			MX7D_PAD_LCD_DATA17__LCD_DATA17		0x79
+			MX7D_PAD_LCD_DATA18__LCD_DATA18		0x79 /* SODIMM 136 */
+			MX7D_PAD_LCD_DATA19__LCD_DATA19		0x79 /* SODIMM 138 */
+			MX7D_PAD_LCD_DATA20__LCD_DATA20		0x79 /* SODIMM 140 */
+			MX7D_PAD_LCD_DATA21__LCD_DATA21		0x79 /* SODIMM 142 */
+			MX7D_PAD_LCD_DATA22__LCD_DATA22		0x79 /* SODIMM 144 */
+			MX7D_PAD_LCD_DATA23__LCD_DATA23		0x79 /* SODIMM 146 */
 		>;
 	};
 
-	pinctrl_lcdif_dat_24: lcdif-dat-24-grp {
+	pinctrl_lcdif_ctrl: lcdifctrlgrp {
 		fsl,pins = <
-			MX7D_PAD_LCD_DATA18__LCD_DATA18		0x79
-			MX7D_PAD_LCD_DATA19__LCD_DATA19		0x79
-			MX7D_PAD_LCD_DATA20__LCD_DATA20		0x79
-			MX7D_PAD_LCD_DATA21__LCD_DATA21		0x79
-			MX7D_PAD_LCD_DATA22__LCD_DATA22		0x79
-			MX7D_PAD_LCD_DATA23__LCD_DATA23		0x79
+			MX7D_PAD_LCD_CLK__LCD_CLK		0x79 /* SODIMM 56 */
+			MX7D_PAD_LCD_ENABLE__LCD_ENABLE		0x79 /* SODIMM 44 */
+			MX7D_PAD_LCD_HSYNC__LCD_HSYNC		0x79 /* SODIMM 68 */
+			MX7D_PAD_LCD_VSYNC__LCD_VSYNC		0x79 /* SODIMM 82 */
 		>;
 	};
 
-	pinctrl_lcdif_ctrl: lcdif-ctrl-grp {
+	pinctrl_lvds_transceiver: lvdstxgrp {
 		fsl,pins = <
-			MX7D_PAD_LCD_CLK__LCD_CLK		0x79
-			MX7D_PAD_LCD_ENABLE__LCD_ENABLE		0x79
-			MX7D_PAD_LCD_VSYNC__LCD_VSYNC		0x79
-			MX7D_PAD_LCD_HSYNC__LCD_HSYNC		0x79
+			MX7D_PAD_ENET1_RGMII_RD2__GPIO7_IO2     0x14 /* SODIMM 63 */
+			MX7D_PAD_ENET1_RGMII_RD3__GPIO7_IO3     0x74 /* SODIMM 55 */
+			MX7D_PAD_ENET1_RGMII_TXC__GPIO7_IO11    0x14 /* SODIMM 99 */
+			MX7D_PAD_EPDC_DATA13__GPIO2_IO13        0x14 /* SODIMM 95 */
 		>;
 	};
 
-	pinctrl_pwm1: pwm1-grp {
+	pinctrl_pwm1: pwm1grp {
 		fsl,pins = <
-			MX7D_PAD_GPIO1_IO08__PWM1_OUT		0x79
-			MX7D_PAD_ECSPI2_MOSI__GPIO4_IO21	0x4
+			MX7D_PAD_ECSPI2_MOSI__GPIO4_IO21	0x4  /* SODIMM 59 */
+			MX7D_PAD_GPIO1_IO08__PWM1_OUT		0x79 /* SODIMM 59 */
 		>;
 	};
 
-	pinctrl_pwm2: pwm2-grp {
+	pinctrl_pwm2: pwm2grp {
 		fsl,pins = <
-			MX7D_PAD_GPIO1_IO09__PWM2_OUT		0x79
+			MX7D_PAD_GPIO1_IO09__PWM2_OUT		0x79 /* SODIMM 28 */
 		>;
 	};
 
-	pinctrl_pwm3: pwm3-grp {
+	pinctrl_pwm3: pwm3grp {
 		fsl,pins = <
-			MX7D_PAD_GPIO1_IO10__PWM3_OUT		0x79
+			MX7D_PAD_GPIO1_IO10__PWM3_OUT		0x79 /* SODIMM 30 */
 		>;
 	};
 
-	pinctrl_pwm4: pwm4-grp {
+	pinctrl_pwm4: pwm4grp {
 		fsl,pins = <
-			MX7D_PAD_GPIO1_IO11__PWM4_OUT		0x79
-			MX7D_PAD_ECSPI2_SCLK__GPIO4_IO20	0x4
+			MX7D_PAD_ECSPI2_SCLK__GPIO4_IO20	0x4  /* SODIMM 67 */
+			MX7D_PAD_GPIO1_IO11__PWM4_OUT		0x79 /* SODIMM 67 */
 		>;
 	};
 
-	pinctrl_uart1: uart1-grp {
+	pinctrl_uart1: uart1grp {
 		fsl,pins = <
-			MX7D_PAD_UART1_TX_DATA__UART1_DTE_RX	0x79
-			MX7D_PAD_UART1_RX_DATA__UART1_DTE_TX	0x79
-			MX7D_PAD_SAI2_TX_BCLK__UART1_DTE_CTS	0x79
-			MX7D_PAD_SAI2_TX_SYNC__UART1_DTE_RTS	0x79
+			MX7D_PAD_SAI2_TX_BCLK__UART1_DTE_CTS	0x79 /* SODIMM 25 */
+			MX7D_PAD_SAI2_TX_SYNC__UART1_DTE_RTS	0x79 /* SODIMM 27 */
+			MX7D_PAD_UART1_RX_DATA__UART1_DTE_TX	0x79 /* SODIMM 35 */
+			MX7D_PAD_UART1_TX_DATA__UART1_DTE_RX	0x79 /* SODIMM 33 */
 		>;
 	};
 
-	pinctrl_uart1_ctrl1: uart1-ctrl1-grp {
+	pinctrl_uart1_ctrl1: uart1ctrl1grp {
 		fsl,pins = <
-			MX7D_PAD_SD2_DATA1__GPIO5_IO15		0x14 /* DCD */
-			MX7D_PAD_SD2_DATA0__GPIO5_IO14		0x14 /* DTR */
+			MX7D_PAD_SD2_DATA0__GPIO5_IO14		0x14 /* SODIMM 23 / DTR */
+			MX7D_PAD_SD2_DATA1__GPIO5_IO15		0x14 /* SODIMM 31 / DCD */
 		>;
 	};
 
-	pinctrl_uart2: uart2-grp {
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX7D_PAD_SAI2_RX_DATA__UART2_DTE_RTS	0x79 /* SODIMM 32 / CTS */
+			MX7D_PAD_SAI2_TX_DATA__UART2_DTE_CTS	0x79 /* SODIMM 34 / RTS */
+			MX7D_PAD_UART2_RX_DATA__UART2_DTE_TX	0x79 /* SODIMM 38 */
+			MX7D_PAD_UART2_TX_DATA__UART2_DTE_RX	0x79 /* SODIMM 36 */
+		>;
+	};
+	pinctrl_uart3: uart3grp {
 		fsl,pins = <
-			MX7D_PAD_UART2_TX_DATA__UART2_DTE_RX 0x79
-			MX7D_PAD_UART2_RX_DATA__UART2_DTE_TX 0x79
-			MX7D_PAD_SAI2_RX_DATA__UART2_DTE_RTS 0x79
-			MX7D_PAD_SAI2_TX_DATA__UART2_DTE_CTS 0x79
+			MX7D_PAD_UART3_RX_DATA__UART3_DTE_TX	0x79 /* SODIMM 21 */
+			MX7D_PAD_UART3_TX_DATA__UART3_DTE_RX	0x79 /* SODIMM 19 */
 		>;
 	};
-	pinctrl_uart3: uart3-grp {
+
+	pinctrl_usbc_det: usbcdetgrp {
 		fsl,pins = <
-			MX7D_PAD_UART3_TX_DATA__UART3_DTE_RX 0x79
-			MX7D_PAD_UART3_RX_DATA__UART3_DTE_TX 0x79
+			MX7D_PAD_ENET1_CRS__GPIO7_IO14		0x14 /* SODIMM 137 / USBC_DET */
 		>;
 	};
 
-	pinctrl_usbc_det: gpio-usbc-det {
+	pinctrl_usbh_reg: usbhreggrp {
 		fsl,pins = <
-			MX7D_PAD_ENET1_CRS__GPIO7_IO14	0x14
+			MX7D_PAD_UART3_CTS_B__GPIO4_IO7		0x14 /* SODIMM 129 / USBH_PEN */
 		>;
 	};
 
-	pinctrl_usbh_reg: gpio-usbh-vbus {
+	pinctrl_usdhc1: usdhc1grp {
 		fsl,pins = <
-			MX7D_PAD_UART3_CTS_B__GPIO4_IO7	0x14 /* SODIMM 129 USBH PEN */
+			MX7D_PAD_SD1_CLK__SD1_CLK		0x19 /* SODIMM 47 */
+			MX7D_PAD_SD1_CMD__SD1_CMD		0x59 /* SODIMM 190 */
+			MX7D_PAD_SD1_DATA0__SD1_DATA0		0x59 /* SODIMM 192 */
+			MX7D_PAD_SD1_DATA1__SD1_DATA1		0x59 /* SODIMM 49 */
+			MX7D_PAD_SD1_DATA2__SD1_DATA2		0x59 /* SODIMM 51 */
+			MX7D_PAD_SD1_DATA3__SD1_DATA3		0x59 /* SODIMM 53 */
 		>;
 	};
 
-	pinctrl_usdhc1: usdhc1-grp {
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
 		fsl,pins = <
-			MX7D_PAD_SD1_CMD__SD1_CMD	0x59
-			MX7D_PAD_SD1_CLK__SD1_CLK	0x19
-			MX7D_PAD_SD1_DATA0__SD1_DATA0	0x59
-			MX7D_PAD_SD1_DATA1__SD1_DATA1	0x59
-			MX7D_PAD_SD1_DATA2__SD1_DATA2	0x59
-			MX7D_PAD_SD1_DATA3__SD1_DATA3	0x59
+			MX7D_PAD_SD1_CLK__SD1_CLK		0x1a
+			MX7D_PAD_SD1_CMD__SD1_CMD		0x5a
+			MX7D_PAD_SD1_DATA0__SD1_DATA0		0x5a
+			MX7D_PAD_SD1_DATA1__SD1_DATA1		0x5a
+			MX7D_PAD_SD1_DATA2__SD1_DATA2		0x5a
+			MX7D_PAD_SD1_DATA3__SD1_DATA3		0x5a
 		>;
 	};
 
-	pinctrl_usdhc1_100mhz: usdhc1grp_100mhz {
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
 		fsl,pins = <
-			MX7D_PAD_SD1_CMD__SD1_CMD	0x5a
-			MX7D_PAD_SD1_CLK__SD1_CLK	0x1a
-			MX7D_PAD_SD1_DATA0__SD1_DATA0	0x5a
-			MX7D_PAD_SD1_DATA1__SD1_DATA1	0x5a
-			MX7D_PAD_SD1_DATA2__SD1_DATA2	0x5a
-			MX7D_PAD_SD1_DATA3__SD1_DATA3	0x5a
+			MX7D_PAD_SD1_CLK__SD1_CLK		0x1b
+			MX7D_PAD_SD1_CMD__SD1_CMD		0x5b
+			MX7D_PAD_SD1_DATA0__SD1_DATA0		0x5b
+			MX7D_PAD_SD1_DATA1__SD1_DATA1		0x5b
+			MX7D_PAD_SD1_DATA2__SD1_DATA2		0x5b
+			MX7D_PAD_SD1_DATA3__SD1_DATA3		0x5b
 		>;
 	};
 
-	pinctrl_usdhc1_200mhz: usdhc1grp_200mhz {
+	/* Avoid backfeeding with removed card power. */
+	pinctrl_usdhc1_sleep: usdhc1-slpgrp {
 		fsl,pins = <
-			MX7D_PAD_SD1_CMD__SD1_CMD	0x5b
-			MX7D_PAD_SD1_CLK__SD1_CLK	0x1b
-			MX7D_PAD_SD1_DATA0__SD1_DATA0	0x5b
-			MX7D_PAD_SD1_DATA1__SD1_DATA1	0x5b
-			MX7D_PAD_SD1_DATA2__SD1_DATA2	0x5b
-			MX7D_PAD_SD1_DATA3__SD1_DATA3	0x5b
+			MX7D_PAD_SD1_CMD__SD1_CMD		0x10
+			MX7D_PAD_SD1_CLK__SD1_CLK		0x10
+			MX7D_PAD_SD1_DATA0__SD1_DATA0		0x10
+			MX7D_PAD_SD1_DATA1__SD1_DATA1		0x10
+			MX7D_PAD_SD1_DATA2__SD1_DATA2		0x10
+			MX7D_PAD_SD1_DATA3__SD1_DATA3		0x10
 		>;
 	};
 
 	pinctrl_usdhc3: usdhc3grp {
 		fsl,pins = <
-			MX7D_PAD_SD3_CMD__SD3_CMD		0x59
 			MX7D_PAD_SD3_CLK__SD3_CLK		0x19
+			MX7D_PAD_SD3_CMD__SD3_CMD		0x59
 			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x59
 			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x59
 			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x59
@@ -847,10 +1042,10 @@
 		>;
 	};
 
-	pinctrl_usdhc3_100mhz: usdhc3grp_100mhz {
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
 		fsl,pins = <
-			MX7D_PAD_SD3_CMD__SD3_CMD		0x5a
 			MX7D_PAD_SD3_CLK__SD3_CLK		0x1a
+			MX7D_PAD_SD3_CMD__SD3_CMD		0x5a
 			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x5a
 			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x5a
 			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x5a
@@ -863,10 +1058,10 @@
 		>;
 	};
 
-	pinctrl_usdhc3_200mhz: usdhc3grp_200mhz {
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
 		fsl,pins = <
-			MX7D_PAD_SD3_CMD__SD3_CMD		0x5b
 			MX7D_PAD_SD3_CLK__SD3_CLK		0x1b
+			MX7D_PAD_SD3_CMD__SD3_CMD		0x5b
 			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x5b
 			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x5b
 			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x5b
@@ -879,16 +1074,16 @@
 		>;
 	};
 
-	pinctrl_sai1: sai1-grp {
+	pinctrl_sai1: sai1grp {
 		fsl,pins = <
-			MX7D_PAD_ENET1_RX_CLK__SAI1_TX_BCLK     0x1f
-			MX7D_PAD_SAI1_TX_SYNC__SAI1_TX_SYNC	0x1f
 			MX7D_PAD_ENET1_COL__SAI1_TX_DATA0	0x30
+			MX7D_PAD_ENET1_RX_CLK__SAI1_TX_BCLK     0x1f
 			MX7D_PAD_ENET1_TX_CLK__SAI1_RX_DATA0	0x1f
+			MX7D_PAD_SAI1_TX_SYNC__SAI1_TX_SYNC	0x1f
 		>;
 	};
 
-	pinctrl_sai1_mclk: sai1grp_mclk {
+	pinctrl_sai1_mclk: sai1mclkgrp {
 		fsl,pins = <
 			MX7D_PAD_SAI1_MCLK__SAI1_MCLK           0x1f
 		>;
@@ -899,23 +1094,35 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_gpio_lpsr>;
 
-	pinctrl_gpio_lpsr: gpio1-grp {
+	pinctrl_cd_usdhc1: cdusdhc1grp {
 		fsl,pins = <
-			MX7D_PAD_LPSR_GPIO1_IO02__GPIO1_IO2	0x59
-			MX7D_PAD_LPSR_GPIO1_IO03__GPIO1_IO3	0x59
+			MX7D_PAD_LPSR_GPIO1_IO00__GPIO1_IO0	0x59 /* SODIMM 43 / MMC_CD */
+		>;
+	};
+
+	pinctrl_cd_usdhc1_sleep: cdusdhc1-slpgrp {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO00__GPIO1_IO0	0x0
+		>;
+	};
+
+	pinctrl_gpio_lpsr: gpiolpsrgrp {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO02__GPIO1_IO2	0x59 /* SODIMM 135 */
+			MX7D_PAD_LPSR_GPIO1_IO03__GPIO1_IO3	0x59 /* SODIMM 22 */
 		>;
 	};
 
 	pinctrl_gpiokeys: gpiokeysgrp {
 		fsl,pins = <
-			MX7D_PAD_LPSR_GPIO1_IO01__GPIO1_IO1	0x19
+			MX7D_PAD_LPSR_GPIO1_IO01__GPIO1_IO1	0x19 /* SODIMM 45 / WAKE_UP */
 		>;
 	};
 
-	pinctrl_i2c1: i2c1-grp {
+	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
-			MX7D_PAD_LPSR_GPIO1_IO05__I2C1_SDA	0x4000007f
 			MX7D_PAD_LPSR_GPIO1_IO04__I2C1_SCL	0x4000007f
+			MX7D_PAD_LPSR_GPIO1_IO05__I2C1_SDA	0x4000007f
 		>;
 	};
 
@@ -926,16 +1133,10 @@
 		>;
 	};
 
-	pinctrl_cd_usdhc1: usdhc1-cd-grp {
-		fsl,pins = <
-			MX7D_PAD_LPSR_GPIO1_IO00__GPIO1_IO0	0x59 /* CD */
-		>;
-	};
-
-	pinctrl_uart1_ctrl2: uart1-ctrl2-grp {
+	pinctrl_uart1_ctrl2: uart1ctrl2grp {
 		fsl,pins = <
-			MX7D_PAD_LPSR_GPIO1_IO07__GPIO1_IO7	0x14 /* DSR */
-			MX7D_PAD_LPSR_GPIO1_IO06__GPIO1_IO6	0x14 /* RI */
+			MX7D_PAD_LPSR_GPIO1_IO06__GPIO1_IO6	0x14 /* SODIMM 37 / RI */
+			MX7D_PAD_LPSR_GPIO1_IO07__GPIO1_IO7	0x14 /* SODIMM 29 / DSR */
 		>;
 	};
 };
diff --git a/arch/arm/boot/dts/imx7-mba7.dtsi b/arch/arm/boot/dts/nxp/imx/imx7-mba7.dtsi
index 3df6dff7734a..4d948a9757f9 100644
--- a/arch/arm/boot/dts/imx7-mba7.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx7-mba7.dtsi
@@ -18,6 +18,8 @@
 		mmc0 = &usdhc3;
 		mmc1 = &usdhc1;
 		/delete-property/ mmc2;
+		rtc0 = &ds1339;
+		rtc1 = &snvs_rtc;
 	};
 
 	beeper {
@@ -32,11 +34,18 @@
 	gpio_buttons: gpio-keys {
 		compatible = "gpio-keys";
 
+		/*
+		 * NOTE: These buttons are attached to a GPIO-expander.
+		 * Enabling wakeup-source, enables wakeup on all inputs.
+		 * If PE_GPIO[3..6] are used as inputs, they cause a
+		 * wakeup as well.
+		 */
 		button-0 {
 			/* #SWITCH_A */
 			label = "S11";
 			linux,code = <KEY_1>;
 			gpios = <&pca9555 13 GPIO_ACTIVE_LOW>;
+			wakeup-source;
 		};
 
 		button-1 {
@@ -44,6 +53,7 @@
 			label = "S12";
 			linux,code = <KEY_2>;
 			gpios = <&pca9555 14 GPIO_ACTIVE_LOW>;
+			wakeup-source;
 		};
 
 		button-2 {
@@ -51,6 +61,7 @@
 			label = "S13";
 			linux,code = <KEY_3>;
 			gpios = <&pca9555 15 GPIO_ACTIVE_LOW>;
+			wakeup-source;
 		};
 	};
 
@@ -70,32 +81,10 @@
 		};
 	};
 
-	reg_sd1_vmmc: regulator-sd1-vmmc {
-		compatible = "regulator-fixed";
-		regulator-name = "VCC3V3_SD1";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-
-	reg_fec1_pwdn: regulator-fec1-pwdn {
-		compatible = "regulator-fixed";
-		regulator-name = "PWDN_FEC1";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-		gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	reg_fec2_pwdn: regulator-fec2-pwdn {
-		compatible = "regulator-fixed";
-		regulator-name = "PWDN_FEC2";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-		gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>,
+			      <&adc2 0>, <&adc2 1>, <&adc2 2>, <&adc2 3>;
 	};
 
 	reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
@@ -124,6 +113,7 @@
 		gpio = <&pca9555 12 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 		regulator-always-on;
+		vin-supply = <&reg_mba_5v>;
 	};
 
 	reg_mpcie_3v3: regulator-mpcie-3v3 {
@@ -134,6 +124,7 @@
 		gpio = <&pca9555 10 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 		regulator-always-on;
+		vin-supply = <&reg_mba_3v3>;
 	};
 
 	reg_mba_12v0: regulator-mba-12v0 {
@@ -145,13 +136,18 @@
 		enable-active-high;
 	};
 
-	reg_lvds_transmitter: regulator-lvds-transmitter {
+	reg_mba_5v: regulator-mba-5v {
 		compatible = "regulator-fixed";
-		regulator-name = "#SHTDN_LVDS";
+		regulator-name = "VCC5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_mba_3v3: regulator-mba-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC3V3";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
-		gpio = <&pca9555 1 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
 	};
 
 	reg_vref_1v8: regulator-vref-1v8 {
@@ -169,11 +165,12 @@
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 		regulator-always-on;
+		vin-supply = <&reg_mba_3v3>;
 	};
 
 	sound {
 		compatible = "fsl,imx-audio-tlv320aic32x4";
-		model = "imx-audio-tlv320aic32x4";
+		model = "tqm-tlv320aic32";
 		ssi-controller = <&sai1>;
 		audio-codec = <&tlv320aic32x4>;
 		audio-routing =
@@ -198,9 +195,9 @@
 
 &ecspi1 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi1>;
+	pinctrl-0 = <&pinctrl_ecspi1>, <&pinctrl_ecspi1_ss0>;
 	cs-gpios = <&gpio4 0 GPIO_ACTIVE_LOW>, <&gpio4 1 GPIO_ACTIVE_LOW>,
-		   <&gpio4 2 GPIO_ACTIVE_LOW>;
+		   <&gpio4 2 GPIO_ACTIVE_LOW>, <&gpio4 19 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
@@ -214,9 +211,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet1>;
 	phy-mode = "rgmii-id";
-	phy-reset-gpios = <&gpio7 15 GPIO_ACTIVE_LOW>;
-	phy-reset-duration = <1>;
-	phy-supply = <&reg_fec1_pwdn>;
 	phy-handle = <&ethphy1_0>;
 	fsl,magic-packet;
 	status = "okay";
@@ -228,10 +222,17 @@
 		ethphy1_0: ethernet-phy@0 {
 			compatible = "ethernet-phy-ieee802.3-c22";
 			reg = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_enet1_phy>;
 			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
 			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
 			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
 			ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+			reset-gpios = <&gpio7 15 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <1000>;
+			reset-deassert-us = <500>;
+			interrupt-parent = <&gpio1>;
+			interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
 		};
 	};
 };
@@ -288,15 +289,19 @@
 
 &i2c1 {
 	lm75: temperature-sensor@49 {
-		compatible = "national,lm75";
+		compatible = "national,lm75a";
 		reg = <0x49>;
+		vs-supply = <&reg_mba_3v3>;
 	};
 };
 
 &i2c2 {
 	clock-frequency = <100000>;
-	pinctrl-names = "default";
+	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_recovery>;
+	scl-gpios = <&gpio4 10 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio4 11 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 
 	tlv320aic32x4: audio-codec@18 {
@@ -319,13 +324,17 @@
 		interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
+		vcc-supply = <&reg_mba_3v3>;
 	};
 };
 
 &i2c3 {
 	clock-frequency = <100000>;
-	pinctrl-names = "default";
+	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c3>;
+	pinctrl-1 = <&pinctrl_i2c3_recovery>;
+	scl-gpios = <&gpio4 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio4 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 };
 
@@ -334,213 +343,213 @@
 	pinctrl-0 = <&pinctrl_hog_mba7_1>;
 
 	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins =
+			<MX7D_PAD_ECSPI1_MISO__ECSPI1_MISO		0x7c>,
+			<MX7D_PAD_ECSPI1_MOSI__ECSPI1_MOSI		0x74>,
+			<MX7D_PAD_ECSPI1_SCLK__ECSPI1_SCLK		0x74>,
+			<MX7D_PAD_UART1_RX_DATA__GPIO4_IO0		0x74>,
+			<MX7D_PAD_UART1_TX_DATA__GPIO4_IO1		0x74>,
+			<MX7D_PAD_UART2_RX_DATA__GPIO4_IO2		0x74>;
+	};
+
+	pinctrl_ecspi1_ss0: ecspi1ss0grp {
 		fsl,pins = <
-			MX7D_PAD_ECSPI1_MISO__ECSPI1_MISO		0x7c
-			MX7D_PAD_ECSPI1_MOSI__ECSPI1_MOSI		0x74
-			MX7D_PAD_ECSPI1_SCLK__ECSPI1_SCLK		0x74
-			MX7D_PAD_UART1_RX_DATA__GPIO4_IO0		0x74
-			MX7D_PAD_UART1_TX_DATA__GPIO4_IO1		0x74
-			MX7D_PAD_UART2_RX_DATA__GPIO4_IO2		0x74
+			MX7D_PAD_ECSPI1_SS0__GPIO4_IO19			0x74
 		>;
 	};
 
 	pinctrl_ecspi2: ecspi2grp {
-		fsl,pins = <
-			MX7D_PAD_ECSPI2_MISO__ECSPI2_MISO		0x7c
-			MX7D_PAD_ECSPI2_MOSI__ECSPI2_MOSI		0x74
-			MX7D_PAD_ECSPI2_SCLK__ECSPI2_SCLK		0x74
-			MX7D_PAD_ECSPI2_SS0__ECSPI2_SS0			0x74
-		>;
+		fsl,pins =
+			<MX7D_PAD_ECSPI2_MISO__ECSPI2_MISO		0x7c>,
+			<MX7D_PAD_ECSPI2_MOSI__ECSPI2_MOSI		0x74>,
+			<MX7D_PAD_ECSPI2_SCLK__ECSPI2_SCLK		0x74>,
+			<MX7D_PAD_ECSPI2_SS0__ECSPI2_SS0		0x74>;
 	};
 
 	pinctrl_enet1: enet1grp {
-		fsl,pins = <
-			MX7D_PAD_GPIO1_IO10__ENET1_MDIO			0x02
-			MX7D_PAD_GPIO1_IO11__ENET1_MDC			0x00
-			MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC	0x71
-			MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0	0x71
-			MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1	0x71
-			MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2	0x71
-			MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3	0x71
-			MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL	0x71
-			MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC	0x79
-			MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0	0x79
-			MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1	0x79
-			MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2	0x79
-			MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3	0x79
-			MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL	0x79
+		fsl,pins =
+			<MX7D_PAD_GPIO1_IO10__ENET1_MDIO			0x02>,
+			<MX7D_PAD_GPIO1_IO11__ENET1_MDC				0x00>,
+			<MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC		0x71>,
+			<MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0		0x71>,
+			<MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1		0x71>,
+			<MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2		0x71>,
+			<MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3		0x71>,
+			<MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL	0x71>,
+			<MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC		0x79>,
+			<MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0		0x79>,
+			<MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1		0x79>,
+			<MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2		0x79>,
+			<MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3		0x79>,
+			<MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL	0x79>;
+	};
+
+	pinctrl_enet1_phy: enet1phygrp {
+		fsl,pins =
 			/* Reset: SION, 100kPU, SRE_FAST, DSE_X1 */
-			MX7D_PAD_ENET1_COL__GPIO7_IO15		0x40000070
+			<MX7D_PAD_ENET1_COL__GPIO7_IO15				0x40000070>,
 			/* INT/PWDN: SION, 100kPU, HYS, SRE_FAST, DSE_X1 */
-			MX7D_PAD_GPIO1_IO09__GPIO1_IO9		0x40000078
-		>;
+			<MX7D_PAD_GPIO1_IO09__GPIO1_IO9				0x40000078>;
 	};
 
 	pinctrl_flexcan1: flexcan1grp {
-		fsl,pins = <
-			MX7D_PAD_GPIO1_IO12__FLEXCAN1_RX	0x5a
-			MX7D_PAD_GPIO1_IO13__FLEXCAN1_TX	0x52
-		>;
+		fsl,pins =
+			<MX7D_PAD_GPIO1_IO12__FLEXCAN1_RX	0x5a>,
+			<MX7D_PAD_GPIO1_IO13__FLEXCAN1_TX	0x52>;
 	};
 
 	pinctrl_flexcan2: flexcan2grp {
-		fsl,pins = <
-			MX7D_PAD_GPIO1_IO14__FLEXCAN2_RX	0x5a
-			MX7D_PAD_GPIO1_IO15__FLEXCAN2_TX	0x52
-		>;
+		fsl,pins =
+			<MX7D_PAD_GPIO1_IO14__FLEXCAN2_RX	0x5a>,
+			<MX7D_PAD_GPIO1_IO15__FLEXCAN2_TX	0x52>;
 	};
 
 	pinctrl_hog_mba7_1: hogmba71grp {
-		fsl,pins = <
+		fsl,pins =
 			/* Limitation: WDOG2_B / WDOG2_RESET not usable */
-			MX7D_PAD_ENET1_RX_CLK__GPIO7_IO13	0x4000007c
-			MX7D_PAD_ENET1_CRS__GPIO7_IO14		0x40000074
+			<MX7D_PAD_ENET1_RX_CLK__GPIO7_IO13	0x4000007c>,
+			<MX7D_PAD_ENET1_CRS__GPIO7_IO14		0x40000074>,
 			/* #BOOT_EN */
-			MX7D_PAD_UART2_TX_DATA__GPIO4_IO3	0x40000010
-		>;
+			<MX7D_PAD_UART2_TX_DATA__GPIO4_IO3	0x40000010>;
 	};
 
 	pinctrl_i2c2: i2c2grp {
-		fsl,pins = <
-			MX7D_PAD_I2C2_SCL__I2C2_SCL		0x40000078
-			MX7D_PAD_I2C2_SDA__I2C2_SDA		0x40000078
-		>;
+		fsl,pins =
+			<MX7D_PAD_I2C2_SCL__I2C2_SCL		0x40000078>,
+			<MX7D_PAD_I2C2_SDA__I2C2_SDA		0x40000078>;
+	};
+
+	pinctrl_i2c2_recovery: i2c2recoverygrp {
+		fsl,pins =
+			<MX7D_PAD_I2C2_SCL__GPIO4_IO10		0x40000078>,
+			<MX7D_PAD_I2C2_SDA__GPIO4_IO11		0x40000078>;
 	};
 
 	pinctrl_i2c3: i2c3grp {
-		fsl,pins = <
-			MX7D_PAD_I2C3_SCL__I2C3_SCL		0x40000078
-			MX7D_PAD_I2C3_SDA__I2C3_SDA		0x40000078
-		>;
+		fsl,pins =
+			<MX7D_PAD_I2C3_SCL__I2C3_SCL		0x40000078>,
+			<MX7D_PAD_I2C3_SDA__I2C3_SDA		0x40000078>;
+	};
+
+	pinctrl_i2c3_recovery: i2c3recoverygrp {
+		fsl,pins =
+			<MX7D_PAD_I2C3_SCL__GPIO4_IO12		0x40000078>,
+			<MX7D_PAD_I2C3_SDA__GPIO4_IO13		0x40000078>;
 	};
 
 	pinctrl_pca9555: pca95550grp {
-		fsl,pins = <
-			MX7D_PAD_ENET1_TX_CLK__GPIO7_IO12	0x78
-		>;
+		fsl,pins =
+			<MX7D_PAD_ENET1_TX_CLK__GPIO7_IO12	0x78>;
 	};
 
 	pinctrl_sai1: sai1grp {
-		fsl,pins = <
-			MX7D_PAD_SAI1_MCLK__SAI1_MCLK		0x11
-			MX7D_PAD_SAI1_RX_BCLK__SAI1_RX_BCLK	0x1c
-			MX7D_PAD_SAI1_RX_DATA__SAI1_RX_DATA0	0x1c
-			MX7D_PAD_SAI1_RX_SYNC__SAI2_RX_SYNC	0x1c
-
-			MX7D_PAD_SAI1_TX_BCLK__SAI1_TX_BCLK	0x1c
-			MX7D_PAD_SAI1_TX_DATA__SAI1_TX_DATA0	0x14
-			MX7D_PAD_SAI1_TX_SYNC__SAI1_TX_SYNC	0x14
-		>;
+		fsl,pins =
+			<MX7D_PAD_SAI1_MCLK__SAI1_MCLK		0x11>,
+			<MX7D_PAD_SAI1_RX_BCLK__SAI1_RX_BCLK	0x1c>,
+			<MX7D_PAD_SAI1_RX_DATA__SAI1_RX_DATA0	0x1c>,
+			<MX7D_PAD_SAI1_RX_SYNC__SAI2_RX_SYNC	0x1c>,
+
+			<MX7D_PAD_SAI1_TX_BCLK__SAI1_TX_BCLK	0x1c>,
+			<MX7D_PAD_SAI1_TX_DATA__SAI1_TX_DATA0	0x14>,
+			<MX7D_PAD_SAI1_TX_SYNC__SAI1_TX_SYNC	0x14>;
 	};
 
 	pinctrl_uart3: uart3grp {
-		fsl,pins = <
-			MX7D_PAD_UART3_RX_DATA__UART3_DCE_RX	0x7e
-			MX7D_PAD_UART3_TX_DATA__UART3_DCE_TX	0x76
-			MX7D_PAD_UART3_CTS_B__UART3_DCE_CTS	0x76
-			MX7D_PAD_UART3_RTS_B__UART3_DCE_RTS	0x7e
-		>;
+		fsl,pins =
+			<MX7D_PAD_UART3_RX_DATA__UART3_DCE_RX	0x7e>,
+			<MX7D_PAD_UART3_TX_DATA__UART3_DCE_TX	0x76>,
+			<MX7D_PAD_UART3_CTS_B__UART3_DCE_CTS	0x76>,
+			<MX7D_PAD_UART3_RTS_B__UART3_DCE_RTS	0x7e>;
 	};
 
 	pinctrl_uart4: uart4grp {
-		fsl,pins = <
-			MX7D_PAD_SAI2_TX_SYNC__UART4_DCE_RX	0x7e
-			MX7D_PAD_SAI2_TX_BCLK__UART4_DCE_TX	0x76
-			MX7D_PAD_SAI2_RX_DATA__UART4_DCE_CTS	0x76
-			MX7D_PAD_SAI2_TX_DATA__UART4_DCE_RTS	0x7e
-		>;
+		fsl,pins =
+			<MX7D_PAD_SAI2_TX_SYNC__UART4_DCE_RX	0x7e>,
+			<MX7D_PAD_SAI2_TX_BCLK__UART4_DCE_TX	0x76>,
+			<MX7D_PAD_SAI2_RX_DATA__UART4_DCE_CTS	0x76>,
+			<MX7D_PAD_SAI2_TX_DATA__UART4_DCE_RTS	0x7e>;
 	};
 
 	pinctrl_uart5: uart5grp {
-		fsl,pins = <
-			MX7D_PAD_I2C4_SCL__UART5_DCE_RX		0x7e
-			MX7D_PAD_I2C4_SDA__UART5_DCE_TX		0x76
-		>;
+		fsl,pins =
+			<MX7D_PAD_I2C4_SCL__UART5_DCE_RX	0x7e>,
+			<MX7D_PAD_I2C4_SDA__UART5_DCE_TX	0x76>;
 	};
 
 	pinctrl_uart6: uart6grp {
-		fsl,pins = <
-			MX7D_PAD_EPDC_DATA08__UART6_DCE_RX	0x7d
-			MX7D_PAD_EPDC_DATA09__UART6_DCE_TX	0x75
-			MX7D_PAD_EPDC_DATA11__UART6_DCE_CTS	0x75
-			MX7D_PAD_EPDC_DATA10__UART6_DCE_RTS	0x7d
-		>;
+		fsl,pins =
+			<MX7D_PAD_EPDC_DATA08__UART6_DCE_RX	0x7d>,
+			<MX7D_PAD_EPDC_DATA09__UART6_DCE_TX	0x75>,
+			<MX7D_PAD_EPDC_DATA11__UART6_DCE_CTS	0x75>,
+			<MX7D_PAD_EPDC_DATA10__UART6_DCE_RTS	0x7d>;
 	};
 
 	pinctrl_uart7: uart7grp {
-		fsl,pins = <
-			MX7D_PAD_EPDC_DATA12__UART7_DCE_RX	0x7e
-			MX7D_PAD_EPDC_DATA13__UART7_DCE_TX	0x76
-			MX7D_PAD_EPDC_DATA15__UART7_DCE_CTS	0x76
+		fsl,pins =
+			<MX7D_PAD_EPDC_DATA12__UART7_DCE_RX	0x7e>,
+			<MX7D_PAD_EPDC_DATA13__UART7_DCE_TX	0x76>,
+			<MX7D_PAD_EPDC_DATA15__UART7_DCE_CTS	0x76>,
 			/* Limitation: RTS is not connected */
-			MX7D_PAD_EPDC_DATA14__UART7_DCE_RTS	0x7e
-		>;
+			<MX7D_PAD_EPDC_DATA14__UART7_DCE_RTS	0x7e>;
 	};
 
-	pinctrl_usdhc1_gpio: usdhc1grp_gpio {
-		fsl,pins = <
+	pinctrl_usdhc1_gpio: usdhc1_gpiogrp {
+		fsl,pins =
 			/* WP */
-			MX7D_PAD_SD1_WP__GPIO5_IO1		0x7c
+			<MX7D_PAD_SD1_WP__GPIO5_IO1		0x7c>,
 			/* CD */
-			MX7D_PAD_SD1_CD_B__GPIO5_IO0		0x7c
+			<MX7D_PAD_SD1_CD_B__GPIO5_IO0		0x7c>,
 			/* VSELECT */
-			MX7D_PAD_GPIO1_IO08__SD1_VSELECT	0x59
-		>;
+			<MX7D_PAD_GPIO1_IO08__SD1_VSELECT	0x59>;
 	};
 
 	pinctrl_usdhc1: usdhc1grp {
-		fsl,pins = <
-			MX7D_PAD_SD1_CMD__SD1_CMD		0x5e
-			MX7D_PAD_SD1_CLK__SD1_CLK		0x57
-			MX7D_PAD_SD1_DATA0__SD1_DATA0		0x5e
-			MX7D_PAD_SD1_DATA1__SD1_DATA1		0x5e
-			MX7D_PAD_SD1_DATA2__SD1_DATA2		0x5e
-			MX7D_PAD_SD1_DATA3__SD1_DATA3		0x5e
-		>;
-	};
-
-	pinctrl_usdhc1_100mhz: usdhc1grp_100mhz {
-		fsl,pins = <
-			MX7D_PAD_SD1_CMD__SD1_CMD		0x5a
-			MX7D_PAD_SD1_CLK__SD1_CLK		0x57
-			MX7D_PAD_SD1_DATA0__SD1_DATA0		0x5a
-			MX7D_PAD_SD1_DATA1__SD1_DATA1		0x5a
-			MX7D_PAD_SD1_DATA2__SD1_DATA2		0x5a
-			MX7D_PAD_SD1_DATA3__SD1_DATA3		0x5a
-		>;
-	};
-
-	pinctrl_usdhc1_200mhz: usdhc1grp_200mhz {
-		fsl,pins = <
-			MX7D_PAD_SD1_CMD__SD1_CMD		0x5b
-			MX7D_PAD_SD1_CLK__SD1_CLK		0x57
-			MX7D_PAD_SD1_DATA0__SD1_DATA0		0x5b
-			MX7D_PAD_SD1_DATA1__SD1_DATA1		0x5b
-			MX7D_PAD_SD1_DATA2__SD1_DATA2		0x5b
-			MX7D_PAD_SD1_DATA3__SD1_DATA3		0x5b
-		>;
+		fsl,pins =
+			<MX7D_PAD_SD1_CMD__SD1_CMD		0x5e>,
+			<MX7D_PAD_SD1_CLK__SD1_CLK		0x57>,
+			<MX7D_PAD_SD1_DATA0__SD1_DATA0		0x5e>,
+			<MX7D_PAD_SD1_DATA1__SD1_DATA1		0x5e>,
+			<MX7D_PAD_SD1_DATA2__SD1_DATA2		0x5e>,
+			<MX7D_PAD_SD1_DATA3__SD1_DATA3		0x5e>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1_100mhzgrp {
+		fsl,pins =
+			<MX7D_PAD_SD1_CMD__SD1_CMD		0x5a>,
+			<MX7D_PAD_SD1_CLK__SD1_CLK		0x57>,
+			<MX7D_PAD_SD1_DATA0__SD1_DATA0		0x5a>,
+			<MX7D_PAD_SD1_DATA1__SD1_DATA1		0x5a>,
+			<MX7D_PAD_SD1_DATA2__SD1_DATA2		0x5a>,
+			<MX7D_PAD_SD1_DATA3__SD1_DATA3		0x5a>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1_200mhzgrp {
+		fsl,pins =
+			<MX7D_PAD_SD1_CMD__SD1_CMD		0x5b>,
+			<MX7D_PAD_SD1_CLK__SD1_CLK		0x57>,
+			<MX7D_PAD_SD1_DATA0__SD1_DATA0		0x5b>,
+			<MX7D_PAD_SD1_DATA1__SD1_DATA1		0x5b>,
+			<MX7D_PAD_SD1_DATA2__SD1_DATA2		0x5b>,
+			<MX7D_PAD_SD1_DATA3__SD1_DATA3		0x5b>;
 	};
 };
 
 &iomuxc_lpsr {
 	pinctrl_pwm1: pwm1grp {
-		fsl,pins = <
+		fsl,pins =
 			/* LCD_CONTRAST */
-			MX7D_PAD_LPSR_GPIO1_IO01__PWM1_OUT	0x50
-		>;
+			<MX7D_PAD_LPSR_GPIO1_IO01__PWM1_OUT	0x50>;
 	};
 
 	pinctrl_usbotg1: usbotg1grp {
-		fsl,pins = <
-			MX7D_PAD_LPSR_GPIO1_IO04__USB_OTG1_OC	0x5c
-			MX7D_PAD_LPSR_GPIO1_IO05__GPIO1_IO5	0x59
-		>;
+		fsl,pins =
+			<MX7D_PAD_LPSR_GPIO1_IO04__USB_OTG1_OC	0x5c>,
+			<MX7D_PAD_LPSR_GPIO1_IO05__GPIO1_IO5	0x59>;
 	};
 
 	pinctrl_wdog1: wdog1grp {
-		fsl,pins = <
-			MX7D_PAD_LPSR_GPIO1_IO00__WDOG1_WDOG_B	0x30
-		>;
+		fsl,pins =
+			<MX7D_PAD_LPSR_GPIO1_IO00__WDOG1_WDOG_B	0x30>;
 	};
 };
 
@@ -560,6 +569,10 @@
 	status = "okay";
 };
 
+&snvs_pwrkey {
+	status = "okay";
+};
+
 &uart3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart3>;
@@ -605,6 +618,7 @@
 };
 
 &usbh {
+	disable-over-current;
 	status = "okay";
 };
 
@@ -627,9 +641,11 @@
 	pinctrl-2 = <&pinctrl_usdhc1_200mhz>, <&pinctrl_usdhc1_gpio>;
 	cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
 	wp-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
-	vmmc-supply = <&reg_sd1_vmmc>;
+	vmmc-supply = <&reg_mba_3v3>;
 	bus-width = <4>;
 	no-1-8-v;
+	no-sdio;
+	no-mmc;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/imx7-tqma7.dtsi b/arch/arm/boot/dts/nxp/imx/imx7-tqma7.dtsi
index fe42b0a46831..2966a33bc528 100644
--- a/arch/arm/boot/dts/imx7-tqma7.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx7-tqma7.dtsi
@@ -30,8 +30,11 @@
 };
 
 &i2c1 {
-	pinctrl-names = "default";
+	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_recovery>;
+	scl-gpios = <&gpio4 8 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio4 9 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	clock-frequency = <100000>;
 	status = "okay";
 
@@ -109,7 +112,7 @@
 			};
 
 			vgen4_reg: v33 {
-				regulator-min-microvolt = <2850000>;
+				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-always-on;
 			};
@@ -128,26 +131,33 @@
 		};
 	};
 
-	/* NXP SE97BTP with temperature sensor + eeprom */
-	se97b: temperature-sensor-eeprom@1e {
+	/* LM75A temperature sensor, TQMa7x 01xx */
+	lm75a: temperature-sensor@48 {
+		compatible = "national,lm75a";
+		reg = <0x48>;
+		vs-supply = <&vgen4_reg>;
+	};
+
+	/* NXP SE97BTP with temperature sensor + eeprom, TQMa7x 02xx */
+	se97b: temperature-sensor@1e {
 		compatible = "nxp,se97b", "jedec,jc-42.4-temp";
 		reg = <0x1e>;
-		status = "okay";
 	};
 
 	/* ST M24C64 */
 	m24c64: eeprom@50 {
 		compatible = "atmel,24c64";
+		read-only;
 		reg = <0x50>;
 		pagesize = <32>;
-		status = "okay";
+		vcc-supply = <&vgen4_reg>;
 	};
 
 	at24c02: eeprom@56 {
-		compatible = "atmel,24c02";
+		compatible = "nxp,se97b", "atmel,24c02";
 		reg = <0x56>;
 		pagesize = <16>;
-		status = "okay";
+		vcc-supply = <&vgen4_reg>;
 	};
 
 	ds1339: rtc@68 {
@@ -158,91 +168,89 @@
 
 &iomuxc {
 	pinctrl_i2c1: i2c1grp {
-		fsl,pins = <
-			MX7D_PAD_I2C1_SDA__I2C1_SDA	0x40000078
-			MX7D_PAD_I2C1_SCL__I2C1_SCL	0x40000078
-		>;
+		fsl,pins =
+			<MX7D_PAD_I2C1_SDA__I2C1_SDA	0x40000078>,
+			<MX7D_PAD_I2C1_SCL__I2C1_SCL	0x40000078>;
+	};
+
+	pinctrl_i2c1_recovery: i2c1recoverygrp {
+		fsl,pins =
+			<MX7D_PAD_I2C1_SDA__GPIO4_IO9	0x40000078>,
+			<MX7D_PAD_I2C1_SCL__GPIO4_IO8	0x40000078>;
 	};
 
 	pinctrl_pmic1: pmic1grp {
-		fsl,pins = <
-			MX7D_PAD_SD2_RESET_B__GPIO5_IO11	0x4000005C
-		>;
+		fsl,pins =
+			<MX7D_PAD_SD2_RESET_B__GPIO5_IO11	0x4000005C>;
 	};
 
 	pinctrl_qspi: qspigrp {
-		fsl,pins = <
-			MX7D_PAD_EPDC_DATA00__QSPI_A_DATA0	0x5A
-			MX7D_PAD_EPDC_DATA01__QSPI_A_DATA1	0x5A
-			MX7D_PAD_EPDC_DATA02__QSPI_A_DATA2	0x5A
-			MX7D_PAD_EPDC_DATA03__QSPI_A_DATA3	0x5A
-			MX7D_PAD_EPDC_DATA05__QSPI_A_SCLK	0x11
-			MX7D_PAD_EPDC_DATA06__QSPI_A_SS0_B	0x54
-			MX7D_PAD_EPDC_DATA07__QSPI_A_SS1_B	0x54
-		>;
+		fsl,pins =
+			<MX7D_PAD_EPDC_DATA00__QSPI_A_DATA0	0x5A>,
+			<MX7D_PAD_EPDC_DATA01__QSPI_A_DATA1	0x5A>,
+			<MX7D_PAD_EPDC_DATA02__QSPI_A_DATA2	0x5A>,
+			<MX7D_PAD_EPDC_DATA03__QSPI_A_DATA3	0x5A>,
+			<MX7D_PAD_EPDC_DATA05__QSPI_A_SCLK	0x11>,
+			<MX7D_PAD_EPDC_DATA06__QSPI_A_SS0_B	0x54>,
+			<MX7D_PAD_EPDC_DATA07__QSPI_A_SS1_B	0x54>;
 	};
 
 	pinctrl_qspi_reset: qspi_resetgrp {
-		fsl,pins = <
+		fsl,pins =
 			/* #QSPI_RESET */
-			MX7D_PAD_EPDC_DATA04__GPIO2_IO4		0x52
-		>;
+			<MX7D_PAD_EPDC_DATA04__GPIO2_IO4	0x52>;
 	};
 
 	pinctrl_usdhc3: usdhc3grp {
-		fsl,pins = <
-			MX7D_PAD_SD3_CMD__SD3_CMD		0x59
-			MX7D_PAD_SD3_CLK__SD3_CLK		0x56
-			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x59
-			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x59
-			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x59
-			MX7D_PAD_SD3_DATA3__SD3_DATA3		0x59
-			MX7D_PAD_SD3_DATA4__SD3_DATA4		0x59
-			MX7D_PAD_SD3_DATA5__SD3_DATA5		0x59
-			MX7D_PAD_SD3_DATA6__SD3_DATA6		0x59
-			MX7D_PAD_SD3_DATA7__SD3_DATA7		0x59
-			MX7D_PAD_SD3_STROBE__SD3_STROBE		0x19
-		>;
+		fsl,pins =
+			<MX7D_PAD_SD3_CMD__SD3_CMD		0x59>,
+			<MX7D_PAD_SD3_CLK__SD3_CLK		0x56>,
+			<MX7D_PAD_SD3_DATA0__SD3_DATA0		0x59>,
+			<MX7D_PAD_SD3_DATA1__SD3_DATA1		0x59>,
+			<MX7D_PAD_SD3_DATA2__SD3_DATA2		0x59>,
+			<MX7D_PAD_SD3_DATA3__SD3_DATA3		0x59>,
+			<MX7D_PAD_SD3_DATA4__SD3_DATA4		0x59>,
+			<MX7D_PAD_SD3_DATA5__SD3_DATA5		0x59>,
+			<MX7D_PAD_SD3_DATA6__SD3_DATA6		0x59>,
+			<MX7D_PAD_SD3_DATA7__SD3_DATA7		0x59>,
+			<MX7D_PAD_SD3_STROBE__SD3_STROBE	0x19>;
 	};
 
-	pinctrl_usdhc3_100mhz: usdhc3grp_100mhz {
-		fsl,pins = <
-			MX7D_PAD_SD3_CMD__SD3_CMD               0x5a
-			MX7D_PAD_SD3_CLK__SD3_CLK               0x51
-			MX7D_PAD_SD3_DATA0__SD3_DATA0           0x5a
-			MX7D_PAD_SD3_DATA1__SD3_DATA1           0x5a
-			MX7D_PAD_SD3_DATA2__SD3_DATA2           0x5a
-			MX7D_PAD_SD3_DATA3__SD3_DATA3           0x5a
-			MX7D_PAD_SD3_DATA4__SD3_DATA4           0x5a
-			MX7D_PAD_SD3_DATA5__SD3_DATA5           0x5a
-			MX7D_PAD_SD3_DATA6__SD3_DATA6           0x5a
-			MX7D_PAD_SD3_DATA7__SD3_DATA7           0x5a
-			MX7D_PAD_SD3_STROBE__SD3_STROBE         0x1a
-		>;
+	pinctrl_usdhc3_100mhz: usdhc3_100mhzgrp {
+		fsl,pins =
+			<MX7D_PAD_SD3_CMD__SD3_CMD               0x5a>,
+			<MX7D_PAD_SD3_CLK__SD3_CLK               0x51>,
+			<MX7D_PAD_SD3_DATA0__SD3_DATA0           0x5a>,
+			<MX7D_PAD_SD3_DATA1__SD3_DATA1           0x5a>,
+			<MX7D_PAD_SD3_DATA2__SD3_DATA2           0x5a>,
+			<MX7D_PAD_SD3_DATA3__SD3_DATA3           0x5a>,
+			<MX7D_PAD_SD3_DATA4__SD3_DATA4           0x5a>,
+			<MX7D_PAD_SD3_DATA5__SD3_DATA5           0x5a>,
+			<MX7D_PAD_SD3_DATA6__SD3_DATA6           0x5a>,
+			<MX7D_PAD_SD3_DATA7__SD3_DATA7           0x5a>,
+			<MX7D_PAD_SD3_STROBE__SD3_STROBE         0x1a>;
 	};
 
-	pinctrl_usdhc3_200mhz: usdhc3grp_200mhz {
-		fsl,pins = <
-			MX7D_PAD_SD3_CMD__SD3_CMD               0x5b
-			MX7D_PAD_SD3_CLK__SD3_CLK               0x51
-			MX7D_PAD_SD3_DATA0__SD3_DATA0           0x5b
-			MX7D_PAD_SD3_DATA1__SD3_DATA1           0x5b
-			MX7D_PAD_SD3_DATA2__SD3_DATA2           0x5b
-			MX7D_PAD_SD3_DATA3__SD3_DATA3           0x5b
-			MX7D_PAD_SD3_DATA4__SD3_DATA4           0x5b
-			MX7D_PAD_SD3_DATA5__SD3_DATA5           0x5b
-			MX7D_PAD_SD3_DATA6__SD3_DATA6           0x5b
-			MX7D_PAD_SD3_DATA7__SD3_DATA7           0x5b
-			MX7D_PAD_SD3_STROBE__SD3_STROBE         0x1b
-		>;
+	pinctrl_usdhc3_200mhz: usdhc3_200mhzgrp {
+		fsl,pins =
+			<MX7D_PAD_SD3_CMD__SD3_CMD               0x5b>,
+			<MX7D_PAD_SD3_CLK__SD3_CLK               0x51>,
+			<MX7D_PAD_SD3_DATA0__SD3_DATA0           0x5b>,
+			<MX7D_PAD_SD3_DATA1__SD3_DATA1           0x5b>,
+			<MX7D_PAD_SD3_DATA2__SD3_DATA2           0x5b>,
+			<MX7D_PAD_SD3_DATA3__SD3_DATA3           0x5b>,
+			<MX7D_PAD_SD3_DATA4__SD3_DATA4           0x5b>,
+			<MX7D_PAD_SD3_DATA5__SD3_DATA5           0x5b>,
+			<MX7D_PAD_SD3_DATA6__SD3_DATA6           0x5b>,
+			<MX7D_PAD_SD3_DATA7__SD3_DATA7           0x5b>,
+			<MX7D_PAD_SD3_STROBE__SD3_STROBE         0x1b>;
 	};
 };
 
 &iomuxc_lpsr {
 	pinctrl_wdog1: wdog1grp {
-		fsl,pins = <
-			MX7D_PAD_LPSR_GPIO1_IO00__WDOG1_WDOG_B	0x30
-		>;
+		fsl,pins =
+			<MX7D_PAD_LPSR_GPIO1_IO00__WDOG1_WDOG_B	0x30>;
 	};
 };
 
@@ -257,11 +265,14 @@
 		spi-max-frequency = <29000000>;
 		spi-rx-bus-width = <4>;
 		spi-tx-bus-width = <4>;
-	};
-};
+		vcc-supply = <&vgen4_reg>;
 
-&sdma {
-	status = "okay";
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+		};
+	};
 };
 
 &usdhc3 {
@@ -273,6 +284,8 @@
 	assigned-clock-rates = <400000000>;
 	bus-width = <8>;
 	non-removable;
+	no-sd;
+	no-sdio;
 	vmmc-supply = <&vgen4_reg>;
 	vqmmc-supply = <&sw2_reg>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx7d-cl-som-imx7.dts b/arch/arm/boot/dts/nxp/imx/imx7d-cl-som-imx7.dts
index 713483c39c9d..713483c39c9d 100644
--- a/arch/arm/boot/dts/imx7d-cl-som-imx7.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-cl-som-imx7.dts
diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-colibri-aster.dts b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-aster.dts
new file mode 100644
index 000000000000..00ab92e56da4
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-aster.dts
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2017-2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7d-colibri.dtsi"
+#include "imx7-colibri-aster.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7D on Aster Carrier Board";
+	compatible = "toradex,colibri-imx7d-aster",
+		     "toradex,colibri-imx7d",
+		     "fsl,imx7d";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+/* Colibri USBH */
+&usbotg2 {
+	disable-over-current;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx7d-colibri-emmc-aster.dts b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-emmc-aster.dts
index 20480276cb0e..212e0685585d 100644
--- a/arch/arm/boot/dts/imx7d-colibri-emmc-aster.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-emmc-aster.dts
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2017-2020 Toradex AG
+ * Copyright 2017-2022 Toradex
  *
  */
 
@@ -11,10 +11,12 @@
 / {
 	model = "Toradex Colibri iMX7D 1GB (eMMC) on Aster Carrier Board";
 	compatible = "toradex,colibri-imx7d-emmc-aster",
-		     "toradex,colibri-imx7d-emmc", "fsl,imx7d";
+		     "toradex,colibri-imx7d-emmc",
+		     "fsl,imx7d";
 };
 
+/* Colibri USBH */
 &usbotg2 {
-	vbus-supply = <&reg_usbh_vbus>;
+	disable-over-current;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx7d-colibri-emmc-eval-v3.dts b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-emmc-eval-v3.dts
index 8ee73c870b12..1deece7e7129 100644
--- a/arch/arm/boot/dts/imx7d-colibri-emmc-eval-v3.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-emmc-eval-v3.dts
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2017 Toradex AG
+ * Copyright 2017-2022 Toradex
  */
 
 /dts-v1/;
@@ -10,10 +10,12 @@
 / {
 	model = "Toradex Colibri iMX7D 1GB (eMMC) on Colibri Evaluation Board V3";
 	compatible = "toradex,colibri-imx7d-emmc-eval-v3",
-		     "toradex,colibri-imx7d-emmc", "fsl,imx7d";
+		     "toradex,colibri-imx7d-emmc",
+		     "fsl,imx7d";
 };
 
+/* Colibri USBH */
 &usbotg2 {
-	vbus-supply = <&reg_usbh_vbus>;
+	disable-over-current;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-colibri-emmc-iris-v2.dts b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-emmc-iris-v2.dts
new file mode 100644
index 000000000000..22e7863c2e80
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-emmc-iris-v2.dts
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7d-colibri-emmc.dtsi"
+#include "imx7-colibri-iris-v2.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7D 1GB on Iris V2 Carrier Board";
+	compatible = "toradex,colibri-imx7d-emmc-iris-v2",
+		     "toradex,colibri-imx7d-emmc",
+		     "fsl,imx7d";
+};
+
+/* Colibri USBH */
+&usbotg2 {
+	disable-over-current;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-colibri-emmc-iris.dts b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-emmc-iris.dts
new file mode 100644
index 000000000000..a3cf8f50e3dc
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-emmc-iris.dts
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7d-colibri-emmc.dtsi"
+#include "imx7-colibri-iris.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7D 1GB on Iris Carrier Board";
+	compatible = "toradex,colibri-imx7d-emmc-iris",
+		     "toradex,colibri-imx7d-emmc",
+		     "fsl,imx7d";
+};
+
+/* Colibri USBH */
+&usbotg2 {
+	disable-over-current;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx7d-colibri-emmc.dtsi b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-emmc.dtsi
index af39e5370fa1..9670f45eab3b 100644
--- a/arch/arm/boot/dts/imx7d-colibri-emmc.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-emmc.dtsi
@@ -1,18 +1,32 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2017 Toradex AG
+ * Copyright 2017-2022 Toradex
  */
 
 #include "imx7d.dtsi"
 #include "imx7-colibri.dtsi"
 
 / {
+	aliases {
+		/* Required to properly pass MAC addresses from bootloader. */
+		ethernet0 = &fec1;
+		ethernet1 = &fec2;
+		mmc0 = &usdhc3; /* eMMC */
+		mmc1 = &usdhc1; /* MMC/SD slot */
+		/delete-property/ mmc2;
+		/delete-property/ mmc3;
+	};
+
 	memory@80000000 {
 		device_type = "memory";
 		reg = <0x80000000 0x40000000>;
 	};
 };
 
+&cpu1 {
+	cpu-supply = <&reg_DCDC2>;
+};
+
 &gpio6 {
 	gpio-line-names = "",
 			  "",
@@ -39,10 +53,14 @@
 			  "SODIMM_34";
 };
 
+/* Colibri USBH */
 &usbotg2 {
+	disable-over-current;
 	dr_mode = "host";
+	vbus-supply = <&reg_usbh_vbus>;
 };
 
+/* eMMC */
 &usdhc3 {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-colibri-eval-v3.dts b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-eval-v3.dts
new file mode 100644
index 000000000000..33d787617db0
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-eval-v3.dts
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2016-2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7d-colibri.dtsi"
+#include "imx7-colibri-eval-v3.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7D on Colibri Evaluation Board V3";
+	compatible = "toradex,colibri-imx7d-eval-v3",
+		     "toradex,colibri-imx7d",
+		     "fsl,imx7d";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+/*
+ * The Atmel maxtouch controller uses SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2, pwm3.
+ * So if you enable following capacitive touch controller, disable pwm2/pwm3 first.
+ */
+&atmel_mxt_ts {
+	status = "disabled";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+/* Colibri PWM<B> */
+&pwm2 {
+	/* The pwm2 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri PWM<C> */
+&pwm3 {
+	/* The pwm3 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri USBH */
+&usbotg2 {
+	disable-over-current;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-colibri-iris-v2.dts b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-iris-v2.dts
new file mode 100644
index 000000000000..afdb1d06c7f6
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-iris-v2.dts
@@ -0,0 +1,84 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7d-colibri.dtsi"
+#include "imx7-colibri-iris-v2.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7D on Iris V2 Carrier Board";
+	compatible = "toradex,colibri-imx7d-iris-v2",
+		     "toradex,colibri-imx7d",
+		     "fsl,imx7d";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&gpio2 {
+	/*
+	 * This switches the LVDS transceiver to VESA color mapping mode.
+	 */
+	lvds-color-map-hog {
+		gpio-hog;
+		gpios = <13 GPIO_ACTIVE_HIGH>; /* SODIMM 95 */
+		line-name = "LVDS_COLOR_MAP";
+		output-low;
+	};
+};
+
+&gpio7 {
+	/*
+	 * This switches the LVDS transceiver to the 24-bit RGB mode.
+	 */
+	lvds-rgb-mode-hog {
+		gpio-hog;
+		gpios = <2 GPIO_ACTIVE_HIGH>; /* SODIMM 63 */
+		line-name = "LVDS_RGB_MODE";
+		output-low;
+	};
+
+	/*
+	 * This switches the LVDS transceiver to the single-channel
+	 * output mode.
+	 */
+	lvds-ch-mode-hog {
+		gpio-hog;
+		gpios = <3 GPIO_ACTIVE_HIGH>; /* SODIMM 55 */
+		line-name = "LVDS_CH_MODE";
+		output-high;
+	};
+
+	/* This turns the LVDS transceiver on */
+	lvds-power-on-hog {
+		gpio-hog;
+		gpios = <11 GPIO_ACTIVE_HIGH>; /* SODIMM 99 */
+		line-name = "LVDS_POWER_ON";
+		output-high;
+	};
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+/* Colibri USBH */
+&usbotg2 {
+	disable-over-current;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-colibri-iris.dts b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-iris.dts
new file mode 100644
index 000000000000..531b0b99bd5a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-colibri-iris.dts
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7d-colibri.dtsi"
+#include "imx7-colibri-iris.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7D on Iris Carrier Board";
+	compatible = "toradex,colibri-imx7d-iris",
+		     "toradex,colibri-imx7d",
+		     "fsl,imx7d";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+/*
+ * The Atmel maxtouch controller uses SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2, pwm3.
+ * So if you enable following capacitive touch controller, disable pwm2/pwm3 first.
+ */
+&atmel_mxt_ts {
+	status = "disabled";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+/* Colibri PWM<B> */
+&pwm2 {
+	/* The pwm2 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri PWM<C> */
+&pwm3 {
+	/* The pwm3 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri USBH */
+&usbotg2 {
+	disable-over-current;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-colibri.dtsi b/arch/arm/boot/dts/nxp/imx/imx7d-colibri.dtsi
new file mode 100644
index 000000000000..531a45b176a1
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-colibri.dtsi
@@ -0,0 +1,35 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2016-2022 Toradex
+ */
+
+#include "imx7d.dtsi"
+#include "imx7-colibri.dtsi"
+
+/ {
+	aliases {
+		/* Required to properly pass MAC addresses from bootloader. */
+		ethernet0 = &fec1;
+		ethernet1 = &fec2;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+};
+
+&cpu1 {
+	cpu-supply = <&reg_DCDC2>;
+};
+
+/* NAND */
+&gpmi {
+	status = "okay";
+};
+
+/* Colibri USBH */
+&usbotg2 {
+	dr_mode = "host";
+	vbus-supply = <&reg_usbh_vbus>;
+};
diff --git a/arch/arm/boot/dts/imx7d-flex-concentrator-mfg.dts b/arch/arm/boot/dts/nxp/imx/imx7d-flex-concentrator-mfg.dts
index a6d68165fb1e..a6d68165fb1e 100644
--- a/arch/arm/boot/dts/imx7d-flex-concentrator-mfg.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-flex-concentrator-mfg.dts
diff --git a/arch/arm/boot/dts/imx7d-flex-concentrator.dts b/arch/arm/boot/dts/nxp/imx/imx7d-flex-concentrator.dts
index bd6b5285aa8d..9984b343cdf0 100644
--- a/arch/arm/boot/dts/imx7d-flex-concentrator.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-flex-concentrator.dts
@@ -107,7 +107,6 @@
 &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi2>;
-	num-chipselects = <1>;
 	cs-gpios = <&gpio4 23 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
@@ -122,7 +121,6 @@
 &ecspi4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi4>;
-	num-chipselects = <1>;
 	cs-gpios = <&gpio3 3 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
@@ -132,7 +130,7 @@
 	 * TCG specification - Section 6.4.1 Clocking:
 	 * TPM shall support a SPI clock frequency range of 10-24 MHz.
 	 */
-	st33htph: tpm-tis@0 {
+	st33htph: tpm@0 {
 		compatible = "st,st33htpm-spi", "tcg,tpm_tis-spi";
 		reg = <0>;
 		spi-max-frequency = <24000000>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-mba7.dts b/arch/arm/boot/dts/nxp/imx/imx7d-mba7.dts
new file mode 100644
index 000000000000..e3ee16f1aaa9
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-mba7.dts
@@ -0,0 +1,136 @@
+// SPDX-License-Identifier: GPL-2.0 OR X11
+/*
+ * Device Tree Source for TQ-Systems TQMa7D board on MBa7 carrier board.
+ *
+ * Copyright (C) 2016 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ * Copyright (C) 2019 Bruno Thomsen <bruno.thomsen@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "imx7d-tqma7.dtsi"
+#include "imx7-mba7.dtsi"
+
+/ {
+	model = "TQ-Systems TQMa7D board on MBa7 carrier board";
+	compatible = "tq,imx7d-mba7", "tq,imx7d-tqma7", "fsl,imx7d";
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy2_0>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy2_0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_enet2_phy>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+			reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <1000>;
+			reset-deassert-us = <500>;
+			interrupt-parent = <&gpio2>;
+			interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+		};
+	};
+};
+
+&gpio2 {
+	pcie-dis-hog {
+		gpio-hog;
+		gpios = <29 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "pcie-dis";
+	};
+
+	pcie-rst-hog {
+		gpio-hog;
+		gpios = <12 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "pcie-rst";
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog_mba7_1>, <&pinctrl_hog_pcie>;
+
+	pinctrl_enet2: enet2grp {
+		fsl,pins =
+			<MX7D_PAD_SD2_CD_B__ENET2_MDIO			0x02>,
+			<MX7D_PAD_SD2_WP__ENET2_MDC			0x00>,
+			<MX7D_PAD_EPDC_GDSP__ENET2_RGMII_TXC		0x71>,
+			<MX7D_PAD_EPDC_SDCE2__ENET2_RGMII_TD0		0x71>,
+			<MX7D_PAD_EPDC_SDCE3__ENET2_RGMII_TD1		0x71>,
+			<MX7D_PAD_EPDC_GDCLK__ENET2_RGMII_TD2		0x71>,
+			<MX7D_PAD_EPDC_GDOE__ENET2_RGMII_TD3		0x71>,
+			<MX7D_PAD_EPDC_GDRL__ENET2_RGMII_TX_CTL		0x71>,
+			<MX7D_PAD_EPDC_SDCE1__ENET2_RGMII_RXC		0x79>,
+			<MX7D_PAD_EPDC_SDCLK__ENET2_RGMII_RD0		0x79>,
+			<MX7D_PAD_EPDC_SDLE__ENET2_RGMII_RD1		0x79>,
+			<MX7D_PAD_EPDC_SDOE__ENET2_RGMII_RD2		0x79>,
+			<MX7D_PAD_EPDC_SDSHR__ENET2_RGMII_RD3		0x79>,
+			<MX7D_PAD_EPDC_SDCE0__ENET2_RGMII_RX_CTL	0x79>;
+	};
+
+	pinctrl_enet2_phy: enet2phygrp {
+		fsl,pins =
+			/* Reset: SION, 100kPU, SRE_FAST, DSE_X1 */
+			<MX7D_PAD_EPDC_BDR0__GPIO2_IO28		0x40000070>,
+			/* INT/PWDN: SION, 100kPU, HYS, SRE_FAST, DSE_X1 */
+			<MX7D_PAD_EPDC_PWR_STAT__GPIO2_IO31	0x40000078>;
+	};
+
+	pinctrl_hog_pcie: hogpciegrp {
+		fsl,pins =
+			/* #pcie_rst */
+			<MX7D_PAD_SD2_CLK__GPIO5_IO12			0x70>,
+			/* #pcie_dis */
+			<MX7D_PAD_EPDC_BDR1__GPIO2_IO29			0x70>;
+	};
+
+	pinctrl_pcie: pciegrp {
+		fsl,pins =
+			/* #pcie_wake */
+			<MX7D_PAD_EPDC_PWR_COM__GPIO2_IO30		0x70>;
+	};
+};
+
+&iomuxc_lpsr {
+	pinctrl_usbotg2: usbotg2grp {
+		fsl,pins =
+			<MX7D_PAD_LPSR_GPIO1_IO06__USB_OTG2_OC	0x5c>,
+			<MX7D_PAD_LPSR_GPIO1_IO07__GPIO1_IO7	0x59>;
+	};
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	/* 1.5V logically from 3.3V */
+	/* probe deferral not supported */
+	/* pcie-bus-supply = <&reg_mpcie_1v5>; */
+	reset-gpio = <&gpio5 12 GPIO_ACTIVE_LOW>;
+	status = "disabled";
+};
+
+&usbotg2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg2>;
+	vbus-supply = <&reg_usb_otg2_vbus>;
+	disable-over-current;
+	dr_mode = "host";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx7d-meerkat96.dts b/arch/arm/boot/dts/nxp/imx/imx7d-meerkat96.dts
index dd8003bd1fc0..f0fda15f3020 100644
--- a/arch/arm/boot/dts/imx7d-meerkat96.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-meerkat96.dts
@@ -212,7 +212,7 @@
 	keep-power-in-suspend;
 	wakeup-source;
 	vmmc-supply = <&reg_wlreg_on>;
-	vqmmc-supply =<&reg_3p3v>;
+	vqmmc-supply = <&reg_3p3v>;
 	status = "okay";
 
 	brcmf: wifi@1 {
diff --git a/arch/arm/boot/dts/imx7d-nitrogen7.dts b/arch/arm/boot/dts/nxp/imx/imx7d-nitrogen7.dts
index a31de900139d..7acd28658e6f 100644
--- a/arch/arm/boot/dts/imx7d-nitrogen7.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-nitrogen7.dts
@@ -159,7 +159,7 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	pmic: pfuze3000@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze3000";
 		reg = <0x08>;
 
@@ -270,7 +270,7 @@
 	pinctrl-0 = <&pinctrl_i2c3>;
 	status = "okay";
 
-	touch@48 {
+	touchscreen@48 {
 		compatible = "ti,tsc2004";
 		reg = <0x48>;
 		pinctrl-names = "default";
@@ -419,7 +419,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hog_1 &pinctrl_j2>;
 
-	pinctrl_hog_1: hoggrp-1 {
+	pinctrl_hog_1: hoggrp {
 		fsl,pins = <
 			MX7D_PAD_SD3_RESET_B__GPIO6_IO11	0x5d
 			MX7D_PAD_GPIO1_IO13__GPIO1_IO13		0x7d
@@ -665,7 +665,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hog_2>;
 
-	pinctrl_hog_2: hoggrp-2 {
+	pinctrl_hog_2: hoggrp {
 		fsl,pins = <
 			MX7D_PAD_LPSR_GPIO1_IO02__GPIO1_IO2	0x7d
 			MX7D_PAD_LPSR_GPIO1_IO03__CCM_CLKO2	0x7d
diff --git a/arch/arm/boot/dts/imx7d-pico-dwarf.dts b/arch/arm/boot/dts/nxp/imx/imx7d-pico-dwarf.dts
index 5162fe227d1e..1b965652291b 100644
--- a/arch/arm/boot/dts/imx7d-pico-dwarf.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-pico-dwarf.dts
@@ -32,7 +32,7 @@
 };
 
 &i2c1 {
-	clock_frequency = <100000>;
+	clock-frequency = <100000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
@@ -40,6 +40,7 @@
 	sgtl5000: audio-codec@a {
 		reg = <0x0a>;
 		compatible = "fsl,sgtl5000";
+		#sound-dai-cells = <0>;
 		clocks = <&sys_mclk>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_3p3v>;
@@ -52,7 +53,7 @@
 };
 
 &i2c4 {
-	clock_frequency = <100000>;
+	clock-frequency = <100000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
@@ -62,6 +63,7 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 		#interrupt-cells = <2>;
+		interrupt-controller;
 		reg = <0x25>;
 	};
 
diff --git a/arch/arm/boot/dts/imx7d-pico-hobbit.dts b/arch/arm/boot/dts/nxp/imx/imx7d-pico-hobbit.dts
index d917dc4f2f22..6ad39dca7009 100644
--- a/arch/arm/boot/dts/imx7d-pico-hobbit.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-pico-hobbit.dts
@@ -64,7 +64,7 @@
 		interrupt-parent = <&gpio2>;
 		interrupts = <7 0>;
 		spi-max-frequency = <1000000>;
-		pendown-gpio = <&gpio2 7 0>;
+		pendown-gpio = <&gpio2 7 GPIO_ACTIVE_LOW>;
 		vcc-supply = <&reg_3p3v>;
 		ti,x-min = /bits/ 16 <0>;
 		ti,x-max = /bits/ 16 <4095>;
diff --git a/arch/arm/boot/dts/imx7d-pico-nymph.dts b/arch/arm/boot/dts/nxp/imx/imx7d-pico-nymph.dts
index 104a85254adb..af26284297a2 100644
--- a/arch/arm/boot/dts/imx7d-pico-nymph.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-pico-nymph.dts
@@ -43,7 +43,7 @@
 };
 
 &i2c1 {
-	clock_frequency = <100000>;
+	clock-frequency = <100000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
@@ -51,6 +51,7 @@
 	sgtl5000: audio-codec@a {
 		reg = <0x0a>;
 		compatible = "fsl,sgtl5000";
+		#sound-dai-cells = <0>;
 		clocks = <&sys_mclk>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_3p3v>;
@@ -64,7 +65,7 @@
 };
 
 &i2c2 {
-	clock_frequency = <100000>;
+	clock-frequency = <100000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx7d-pico-pi.dts b/arch/arm/boot/dts/nxp/imx/imx7d-pico-pi.dts
index f263e391e24c..62221131336f 100644
--- a/arch/arm/boot/dts/imx7d-pico-pi.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-pico-pi.dts
@@ -61,6 +61,10 @@
 	};
 };
 
+&usdhc1 {
+	status = "disabled";
+};
+
 &iomuxc {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hog>;
diff --git a/arch/arm/boot/dts/imx7d-pico.dtsi b/arch/arm/boot/dts/nxp/imx/imx7d-pico.dtsi
index e519897fae08..a1574ccec89c 100644
--- a/arch/arm/boot/dts/imx7d-pico.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-pico.dtsi
@@ -41,7 +41,7 @@
 		regulator-max-microvolt = <3300000>;
 		gpio = <&gpio1 6 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
-        };
+	};
 
 	reg_wlreg_on: regulator-wlreg_on {
 		compatible = "regulator-fixed";
@@ -108,6 +108,14 @@
 	assigned-clock-rates = <0>, <32768>;
 };
 
+&cpu0 {
+	cpu-supply = <&sw1a_reg>;
+};
+
+&cpu1 {
+	cpu-supply = <&sw1a_reg>;
+};
+
 &ecspi3 {
 	cs-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
@@ -170,7 +178,7 @@
 	pinctrl-0 = <&pinctrl_i2c4>;
 	status = "okay";
 
-	pmic: pfuze3000@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze3000";
 		reg = <0x08>;
 
@@ -432,18 +440,18 @@
 			MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2	0x1
 			MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3	0x1
 			MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL	0x1
-			MX7D_PAD_SD3_RESET_B__GPIO6_IO11                0x1  /* Ethernet reset */
+			MX7D_PAD_SD3_RESET_B__GPIO6_IO11		0x1  /* Ethernet reset */
 		>;
 	};
 
-	pinctrl_can1: can1frp {
+	pinctrl_can1: can1frpgrp {
 		fsl,pins = <
 			MX7D_PAD_SAI1_RX_DATA__FLEXCAN1_RX	0x59
 			MX7D_PAD_SAI1_TX_BCLK__FLEXCAN1_TX	0x59
 		>;
 	};
 
-	pinctrl_can2: can2frp {
+	pinctrl_can2: can2frpgrp {
 		fsl,pins = <
 			MX7D_PAD_SAI1_TX_SYNC__FLEXCAN2_RX	0x59
 			MX7D_PAD_SAI1_TX_DATA__FLEXCAN2_TX	0x59
@@ -491,25 +499,25 @@
 		>;
 	};
 
-	pinctrl_pwm1: pwm1 {
+	pinctrl_pwm1: pwm1grp {
 		fsl,pins = <
-			MX7D_PAD_GPIO1_IO08__PWM1_OUT   0x7f
+			MX7D_PAD_GPIO1_IO08__PWM1_OUT	0x7f
 		>;
 	};
 
-	pinctrl_pwm2: pwm2 {
+	pinctrl_pwm2: pwm2grp {
 		fsl,pins = <
-			MX7D_PAD_GPIO1_IO09__PWM2_OUT   0x7f
+			MX7D_PAD_GPIO1_IO09__PWM2_OUT	0x7f
 		>;
 	};
 
-	pinctrl_pwm3: pwm3 {
+	pinctrl_pwm3: pwm3grp {
 		fsl,pins = <
-			MX7D_PAD_GPIO1_IO10__PWM3_OUT   0x7f
+			MX7D_PAD_GPIO1_IO10__PWM3_OUT	0x7f
 		>;
 	};
 
-	pinctrl_pwm4: pwm4grp{
+	pinctrl_pwm4: pwm4grp {
 		fsl,pins = <
 			MX7D_PAD_GPIO1_IO11__PWM4_OUT	0x7f
 		>;
@@ -555,7 +563,7 @@
 		>;
 	};
 
-	pinctrl_usbotg1_pwr: usbotg_pwr {
+	pinctrl_usbotg1_pwr: usbotgpwrgrp {
 		fsl,pins = <
 			MX7D_PAD_UART3_TX_DATA__GPIO4_IO5	0x14
 		>;
@@ -573,7 +581,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_100mhz: usdhc1grp_100mhz {
+	pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp {
 		fsl,pins = <
 			MX7D_PAD_SD1_CMD__SD1_CMD		0x5a
 			MX7D_PAD_SD1_CLK__SD1_CLK		0x1a
@@ -585,7 +593,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_200mhz: usdhc1grp_200mhz {
+	pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
 		fsl,pins = <
 			MX7D_PAD_SD1_CMD__SD1_CMD		0x5b
 			MX7D_PAD_SD1_CLK__SD1_CLK		0x1b
@@ -623,7 +631,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_100mhz: usdhc3grp_100mhz {
+	pinctrl_usdhc3_100mhz: usdhc3-100mhz-grp {
 		fsl,pins = <
 			MX7D_PAD_SD3_CMD__SD3_CMD		0x5a
 			MX7D_PAD_SD3_CLK__SD3_CLK		0x1a
@@ -638,7 +646,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_200mhz: usdhc3grp_200mhz {
+	pinctrl_usdhc3_200mhz: usdhc3-200mhz-grp {
 		fsl,pins = <
 			MX7D_PAD_SD3_CMD__SD3_CMD		0x5b
 			MX7D_PAD_SD3_CLK__SD3_CLK		0x1b
diff --git a/arch/arm/boot/dts/imx7d-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx7d-pinfunc.h
index 69f2c1ec8254..69f2c1ec8254 100644
--- a/arch/arm/boot/dts/imx7d-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-pinfunc.h
diff --git a/arch/arm/boot/dts/imx7d-remarkable2.dts b/arch/arm/boot/dts/nxp/imx/imx7d-remarkable2.dts
index a2a91bfdd98e..ff9d50942884 100644
--- a/arch/arm/boot/dts/imx7d-remarkable2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-remarkable2.dts
@@ -8,6 +8,7 @@
 /dts-v1/;
 
 #include "imx7d.dtsi"
+#include <dt-bindings/input/linux-event-codes.h>
 
 / {
 	model = "reMarkable 2.0";
@@ -22,6 +23,28 @@
 		reg = <0x80000000 0x40000000>;
 	};
 
+	thermal-zones {
+		epd-thermal {
+			thermal-sensors = <&sy7636a>;
+			polling-delay-passive = <30000>;
+			polling-delay = <30000>;
+
+			trips {
+				trip0 {
+					temperature = <49000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <50000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
 	reg_brcm: regulator-brcm {
 		compatible = "regulator-fixed";
 		regulator-name = "brcm_reg";
@@ -47,6 +70,17 @@
 		startup-delay-us = <100000>; /* 100 ms */
 	};
 
+	reg_touch: regulator-touch {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_3V3_TOUCH";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touch_reg>;
+		gpio = <&gpio1 11 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		pinctrl-names = "default";
@@ -57,6 +91,10 @@
 	};
 };
 
+&cpu0 {
+	cpu-supply = <&buck1>;
+};
+
 &clks {
 	assigned-clocks = <&clks IMX7D_CLKO2_ROOT_SRC>,
 			  <&clks IMX7D_CLKO2_ROOT_DIV>;
@@ -84,6 +122,217 @@
 	};
 };
 
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	bd71815: pmic@4b {
+		compatible = "rohm,bd71815";
+		reg = <0x4b>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_bd71815>;
+		interrupt-parent = <&gpio6>; /* PMIC_INT_B GPIO6_IO16 */
+		interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
+		gpio-controller;
+		clocks = <&clks IMX7D_CLKO2_ROOT_SRC>;
+		clock-output-names = "bd71815-32k-out";
+		#clock-cells = <0>;
+		#gpio-cells = <2>;
+
+		regulators {
+			buck1: buck1 {
+				regulator-name = "buck1";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <2000000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+			};
+
+			buck2: buck2 {
+				regulator-name = "buck2";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <2000000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+			};
+
+			buck3: buck3 {
+				regulator-name = "buck3";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <2700000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck4: buck4 {
+				regulator-name = "buck4";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck5: buck5 {
+				regulator-name = "buck5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1: ldo1 {
+				regulator-name = "ldo1";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo2: ldo2 {
+				regulator-name = "ldo2";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo3: ldo3 {
+				regulator-name = "ldo3";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo4: ldo4 {
+				regulator-name = "ldo4";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo5: ldo5 {
+				regulator-name = "ldo5";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo6: ldodvref {
+				regulator-name = "ldodvref";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo7: ldolpsr {
+				regulator-name = "ldolpsr";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			boost: wled {
+				regulator-name = "wled";
+				regulator-min-microamp = <10>;
+				regulator-max-microamp = <25000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	touchscreen@24 {
+		compatible = "cypress,tt21000";
+		reg = <0x24>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touch>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <14 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+		vdd-supply = <&reg_touch>;
+		touchscreen-size-x = <880>;
+		touchscreen-size-y = <1280>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		button@0 {
+			reg = <0>;
+			linux,keycodes = <KEY_HOMEPAGE>;
+		};
+
+		button@1 {
+			reg = <1>;
+			linux,keycodes = <KEY_MENU>;
+		};
+
+		button@2 {
+			reg = <2>;
+			linux,keycodes = <KEY_BACK>;
+		};
+
+		button@3 {
+			reg = <3>;
+			linux,keycodes = <KEY_SEARCH>;
+		};
+
+		button@4 {
+			reg = <4>;
+			linux,keycodes = <KEY_VOLUMEDOWN>;
+		};
+
+		button@5 {
+			reg = <5>;
+			linux,keycodes = <KEY_VOLUMEUP>;
+		};
+
+		button@6 {
+			reg = <6>;
+			linux,keycodes = <KEY_CAMERA>;
+		};
+
+		button@7 {
+			reg = <7>;
+			linux,keycodes = <KEY_POWER>;
+		};
+	};
+};
+
+&i2c4 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	pinctrl-1 = <&pinctrl_i2c4>;
+	status = "okay";
+
+	sy7636a: pmic@62 {
+		compatible = "silergy,sy7636a";
+		reg = <0x62>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_epdpmic>;
+		#thermal-sensor-cells = <0>;
+		epd-pwr-good-gpios = <&gpio6 21 GPIO_ACTIVE_HIGH>;
+
+		regulators {
+			reg_epdpmic: vcom {
+				regulator-name = "vcom";
+				regulator-boot-on;
+			};
+		};
+	};
+};
+
 &snvs_pwrkey {
 	status = "okay";
 };
@@ -125,7 +374,7 @@
 	cap-power-off-card;
 	status = "okay";
 
-	brcmf: bcrmf@1 {
+	brcmf: wifi@1 {
 		reg = <1>;
 		compatible = "brcm,bcm4329-fmac";
 	};
@@ -170,6 +419,12 @@
 };
 
 &iomuxc {
+	pinctrl_bd71815: bd71815grp {
+		fsl,pins = <
+			MX7D_PAD_SAI1_RX_SYNC__GPIO6_IO16	0x59
+		>;
+	};
+
 	pinctrl_brcm_reg: brcmreggrp {
 		fsl,pins = <
 			/* WIFI_PWR_EN */
@@ -177,6 +432,22 @@
 		>;
 	};
 
+	pinctrl_epdpmic: epdpmicgrp {
+		fsl,pins = <
+			MX7D_PAD_SAI2_RX_DATA__GPIO6_IO21	0x00000074
+			MX7D_PAD_ENET1_RGMII_TXC__GPIO7_IO11	0x00000014
+		>;
+	};
+
+	pinctrl_touch: touchgrp {
+		fsl,pins = <
+			/* CYTTSP interrupt */
+			MX7D_PAD_GPIO1_IO14__GPIO1_IO14		0x54
+			/* CYTTSP reset */
+			MX7D_PAD_GPIO1_IO13__GPIO1_IO13		0x04
+		>;
+	};
+
 	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
 			MX7D_PAD_I2C1_SDA__I2C1_SDA		0x4000007f
@@ -184,6 +455,34 @@
 		>;
 	};
 
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX7D_PAD_I2C2_SDA__I2C2_SDA		0x4000007f
+			MX7D_PAD_I2C2_SCL__I2C2_SCL		0x4000007f
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX7D_PAD_I2C3_SDA__I2C3_SDA		0x4000007f
+			MX7D_PAD_I2C3_SCL__I2C3_SCL		0x4000007f
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX7D_PAD_I2C4_SDA__I2C4_SDA		0x4000007f
+			MX7D_PAD_I2C4_SCL__I2C4_SCL		0x4000007f
+		>;
+	};
+
+	pinctrl_touch_reg: touchreggrp {
+		fsl,pins = <
+			/* TOUCH_PWR_EN */
+			MX7D_PAD_GPIO1_IO11__GPIO1_IO11		0x14
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX	0x79
@@ -209,7 +508,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_100mhz: usdhc2grp_100mhz {
+	pinctrl_usdhc2_100mhz: usdhc2-100mhz-grp {
 		fsl,pins = <
 			MX7D_PAD_SD2_CMD__SD2_CMD		0x5a
 			MX7D_PAD_SD2_CLK__SD2_CLK		0x1a
@@ -220,7 +519,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_200mhz: usdhc2grp_200mhz {
+	pinctrl_usdhc2_200mhz: usdhc2-200mhz-grp {
 		fsl,pins = <
 			MX7D_PAD_SD2_CMD__SD2_CMD		0x5b
 			MX7D_PAD_SD2_CLK__SD2_CLK		0x1b
@@ -247,7 +546,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_100mhz: usdhc3grp_100mhz {
+	pinctrl_usdhc3_100mhz: usdhc3-100mhz-grp {
 		fsl,pins = <
 			MX7D_PAD_SD3_CMD__SD3_CMD		0x5a
 			MX7D_PAD_SD3_CLK__SD3_CLK		0x1a
@@ -263,7 +562,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_200mhz: usdhc3grp_200mhz {
+	pinctrl_usdhc3_200mhz: usdhc3-200mhz-grp {
 		fsl,pins = <
 			MX7D_PAD_SD3_CMD__SD3_CMD		0x5b
 			MX7D_PAD_SD3_CLK__SD3_CLK		0x1b
diff --git a/arch/arm/boot/dts/imx7d-sbc-imx7.dts b/arch/arm/boot/dts/nxp/imx/imx7d-sbc-imx7.dts
index f8a868552707..f8a868552707 100644
--- a/arch/arm/boot/dts/imx7d-sbc-imx7.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-sbc-imx7.dts
diff --git a/arch/arm/boot/dts/imx7d-sdb-reva.dts b/arch/arm/boot/dts/nxp/imx/imx7d-sdb-reva.dts
index cabdaa6dc518..40156cd9195f 100644
--- a/arch/arm/boot/dts/imx7d-sdb-reva.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-sdb-reva.dts
@@ -21,23 +21,21 @@
 };
 
 &iomuxc {
-	imx7d-sdb {
-		pinctrl_tsc2046_pendown: tsc2046_pendown {
-			fsl,pins = <
-				MX7D_PAD_EPDC_DATA13__GPIO2_IO13	0x59
-			>;
-		};
-
-		pinctrl_hog: hoggrp {
-			fsl,pins = <
-				MX7D_PAD_ECSPI2_SS0__GPIO4_IO23		0x34  /* bt reg on */
-			>;
-		};
-
-		pinctrl_usb_otg2_vbus_reg_reva: usbotg2vbusregrevagrp {
-			fsl,pins = <
-				MX7D_PAD_UART3_CTS_B__GPIO4_IO7		0x14
-			>;
-		};
+	pinctrl_tsc2046_pendown: tsc2046-pendowngrp {
+		fsl,pins = <
+			MX7D_PAD_EPDC_DATA13__GPIO2_IO13	0x59
+		>;
+	};
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX7D_PAD_ECSPI2_SS0__GPIO4_IO23		0x34  /* bt reg on */
+		>;
+	};
+
+	pinctrl_usb_otg2_vbus_reg_reva: usbotg2vbusregrevagrp {
+		fsl,pins = <
+			MX7D_PAD_UART3_CTS_B__GPIO4_IO7		0x14
+		>;
 	};
 };
diff --git a/arch/arm/boot/dts/imx7d-sdb-sht11.dts b/arch/arm/boot/dts/nxp/imx/imx7d-sdb-sht11.dts
index 996555596d40..996555596d40 100644
--- a/arch/arm/boot/dts/imx7d-sdb-sht11.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-sdb-sht11.dts
diff --git a/arch/arm/boot/dts/imx7d-sdb.dts b/arch/arm/boot/dts/nxp/imx/imx7d-sdb.dts
index f053f5122741..17236f90ab33 100644
--- a/arch/arm/boot/dts/imx7d-sdb.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-sdb.dts
@@ -10,6 +10,11 @@
 	model = "Freescale i.MX7 SabreSD Board";
 	compatible = "fsl,imx7d-sdb", "fsl,imx7d";
 
+	aliases {
+		ethernet0 = &fec1;
+		ethernet1 = &fec2;
+	};
+
 	chosen {
 		stdout-path = &uart1;
 	};
@@ -24,14 +29,14 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_keys>;
 
-		volume-up {
+		key-volume-up {
 			label = "Volume Up";
 			gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
 			wakeup-source;
 		};
 
-		volume-down {
+		key-volume-down {
 			label = "Volume Down";
 			gpios = <&gpio5 10 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
@@ -39,12 +44,12 @@
 		};
 	};
 
-	spi4 {
+	spi-4 {
 		compatible = "spi-gpio";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_spi4>;
-		gpio-sck = <&gpio1 13 GPIO_ACTIVE_HIGH>;
-		gpio-mosi = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+		sck-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
 		cs-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
 		num-chipselects = <1>;
 		#address-cells = <1>;
@@ -60,6 +65,17 @@
 		};
 	};
 
+	reg_sd1_vmmc: regulator-sd1-vmmc {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_SD1";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <200000>;
+		off-on-delay-us = <20000>;
+	};
+
 	reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "usb_otg1_vbus";
@@ -127,6 +143,33 @@
 		gpio = <&gpio1 4 GPIO_ACTIVE_LOW>;
 	};
 
+	reg_audio_5v: regulator-audio-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "audio-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	reg_audio_3v3: regulator-audio-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "audio-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	reg_audio_1v8: regulator-audio-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "audio-1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
 	backlight: backlight {
 		compatible = "pwm-backlight";
 		pwms = <&pwm1 0 5000000 0>;
@@ -153,7 +196,7 @@
 		model = "wm8960-audio";
 		audio-cpu = <&sai1>;
 		audio-codec = <&codec>;
-		hp-det-gpio = <&gpio2 28 GPIO_ACTIVE_HIGH>;
+		hp-det-gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>;
 		audio-routing =
 			"Headphone Jack", "HP_L",
 			"Headphone Jack", "HP_R",
@@ -201,17 +244,12 @@
 		compatible = "ti,tsc2046";
 		reg = <0>;
 		spi-max-frequency = <1000000>;
-		pinctrl-names ="default";
+		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_tsc2046_pendown>;
 		interrupt-parent = <&gpio2>;
 		interrupts = <29 0>;
-		pendown-gpio = <&gpio2 29 GPIO_ACTIVE_HIGH>;
-		ti,x-min = /bits/ 16 <0>;
-		ti,x-max = /bits/ 16 <0>;
-		ti,y-min = /bits/ 16 <0>;
-		ti,y-max = /bits/ 16 <0>;
-		ti,pressure-max = /bits/ 16 <0>;
-		ti,x-plate-ohms = /bits/ 16 <400>;
+		pendown-gpio = <&gpio2 29 GPIO_ACTIVE_LOW>;
+		touchscreen-max-pressure = <255>;
 		wakeup-source;
 	};
 };
@@ -269,7 +307,7 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	pmic: pfuze3000@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze3000";
 		reg = <0x08>;
 
@@ -395,6 +433,11 @@
 				  <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		assigned-clock-parents = <&clks IMX7D_PLL_AUDIO_POST_DIV>;
 		assigned-clock-rates = <0>, <884736000>, <12288000>;
+		AVDD-supply = <&reg_audio_3v3>;
+		DBVDD-supply = <&reg_audio_1v8>;
+		DCVDD-supply = <&reg_audio_1v8>;
+		SPKVDD1-supply = <&reg_audio_5v>;
+		SPKVDD2-supply = <&reg_audio_5v>;
 	};
 };
 
@@ -478,10 +521,13 @@
 };
 
 &usdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>, <&pinctrl_usdhc1_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>, <&pinctrl_usdhc1_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>, <&pinctrl_usdhc1_gpio>;
 	cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
 	wp-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&reg_sd1_vmmc>;
 	wakeup-source;
 	keep-power-in-suspend;
 	status = "okay";
@@ -523,314 +569,340 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hog>;
 
-	imx7d-sdb {
-		pinctrl_brcm_reg: brcmreggrp {
-			fsl,pins = <
-				MX7D_PAD_ECSPI2_MOSI__GPIO4_IO21	0x14
-			>;
-		};
+	pinctrl_brcm_reg: brcmreggrp {
+		fsl,pins = <
+			MX7D_PAD_ECSPI2_MOSI__GPIO4_IO21	0x14
+		>;
+	};
 
-		pinctrl_ecspi3: ecspi3grp {
-			fsl,pins = <
-				MX7D_PAD_SAI2_TX_SYNC__ECSPI3_MISO	0x2
-				MX7D_PAD_SAI2_TX_BCLK__ECSPI3_MOSI	0x2
-				MX7D_PAD_SAI2_RX_DATA__ECSPI3_SCLK	0x2
-				MX7D_PAD_SD2_CD_B__GPIO5_IO9		0x59
-			>;
-		};
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins = <
+			MX7D_PAD_SAI2_TX_SYNC__ECSPI3_MISO	0x2
+			MX7D_PAD_SAI2_TX_BCLK__ECSPI3_MOSI	0x2
+			MX7D_PAD_SAI2_RX_DATA__ECSPI3_SCLK	0x2
+			MX7D_PAD_SD2_CD_B__GPIO5_IO9		0x59
+		>;
+	};
 
-		pinctrl_enet1: enet1grp {
-			fsl,pins = <
-				MX7D_PAD_GPIO1_IO10__ENET1_MDIO			0x3
-				MX7D_PAD_GPIO1_IO11__ENET1_MDC			0x3
-				MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC	0x1
-				MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0	0x1
-				MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1	0x1
-				MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2	0x1
-				MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3	0x1
-				MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL	0x1
-				MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC	0x1
-				MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0	0x1
-				MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1	0x1
-				MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2	0x1
-				MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3	0x1
-				MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL	0x1
-			>;
-		};
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX7D_PAD_GPIO1_IO10__ENET1_MDIO			0x3
+			MX7D_PAD_GPIO1_IO11__ENET1_MDC			0x3
+			MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC	0x1
+			MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0	0x1
+			MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1	0x1
+			MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2	0x1
+			MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3	0x1
+			MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL	0x1
+			MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC	0x1
+			MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0	0x1
+			MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1	0x1
+			MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2	0x1
+			MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3	0x1
+			MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL	0x1
+		>;
+	};
 
-		pinctrl_enet2: enet2grp {
-			fsl,pins = <
-				MX7D_PAD_EPDC_GDSP__ENET2_RGMII_TXC		0x1
-				MX7D_PAD_EPDC_SDCE2__ENET2_RGMII_TD0		0x1
-				MX7D_PAD_EPDC_SDCE3__ENET2_RGMII_TD1		0x1
-				MX7D_PAD_EPDC_GDCLK__ENET2_RGMII_TD2		0x1
-				MX7D_PAD_EPDC_GDOE__ENET2_RGMII_TD3		0x1
-				MX7D_PAD_EPDC_GDRL__ENET2_RGMII_TX_CTL		0x1
-				MX7D_PAD_EPDC_SDCE1__ENET2_RGMII_RXC		0x1
-				MX7D_PAD_EPDC_SDCLK__ENET2_RGMII_RD0		0x1
-				MX7D_PAD_EPDC_SDLE__ENET2_RGMII_RD1		0x1
-				MX7D_PAD_EPDC_SDOE__ENET2_RGMII_RD2		0x1
-				MX7D_PAD_EPDC_SDSHR__ENET2_RGMII_RD3		0x1
-				MX7D_PAD_EPDC_SDCE0__ENET2_RGMII_RX_CTL		0x1
-			>;
-		};
+	pinctrl_enet2: enet2grp {
+		fsl,pins = <
+			MX7D_PAD_EPDC_GDSP__ENET2_RGMII_TXC		0x1
+			MX7D_PAD_EPDC_SDCE2__ENET2_RGMII_TD0		0x1
+			MX7D_PAD_EPDC_SDCE3__ENET2_RGMII_TD1		0x1
+			MX7D_PAD_EPDC_GDCLK__ENET2_RGMII_TD2		0x1
+			MX7D_PAD_EPDC_GDOE__ENET2_RGMII_TD3		0x1
+			MX7D_PAD_EPDC_GDRL__ENET2_RGMII_TX_CTL		0x1
+			MX7D_PAD_EPDC_SDCE1__ENET2_RGMII_RXC		0x1
+			MX7D_PAD_EPDC_SDCLK__ENET2_RGMII_RD0		0x1
+			MX7D_PAD_EPDC_SDLE__ENET2_RGMII_RD1		0x1
+			MX7D_PAD_EPDC_SDOE__ENET2_RGMII_RD2		0x1
+			MX7D_PAD_EPDC_SDSHR__ENET2_RGMII_RD3		0x1
+			MX7D_PAD_EPDC_SDCE0__ENET2_RGMII_RX_CTL		0x1
+		>;
+	};
 
-		pinctrl_enet2_reg: enet2reggrp {
-			fsl,pins = <
-				MX7D_PAD_LPSR_GPIO1_IO04__GPIO1_IO4	0x14
-			>;
-		};
+	pinctrl_enet2_reg: enet2reggrp {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO04__GPIO1_IO4	0x14
+		>;
+	};
 
-		pinctrl_flexcan2: flexcan2grp {
-			fsl,pins = <
-				MX7D_PAD_GPIO1_IO14__FLEXCAN2_RX	0x59
-				MX7D_PAD_GPIO1_IO15__FLEXCAN2_TX	0x59
-			>;
-		};
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins = <
+			MX7D_PAD_GPIO1_IO14__FLEXCAN2_RX	0x59
+			MX7D_PAD_GPIO1_IO15__FLEXCAN2_TX	0x59
+		>;
+	};
 
-		pinctrl_flexcan2_reg: flexcan2reggrp {
-			fsl,pins = <
-				MX7D_PAD_EPDC_DATA14__GPIO2_IO14	0x59	/* CAN_STBY */
-			>;
-		};
+	pinctrl_flexcan2_reg: flexcan2reggrp {
+		fsl,pins = <
+			MX7D_PAD_EPDC_DATA14__GPIO2_IO14	0x59	/* CAN_STBY */
+		>;
+	};
 
-		pinctrl_gpio_keys: gpio_keysgrp {
-			fsl,pins = <
-				MX7D_PAD_SD2_RESET_B__GPIO5_IO11	0x59
-				MX7D_PAD_SD2_WP__GPIO5_IO10		0x59
-			>;
-		};
+	pinctrl_gpio_keys: gpio-keysgrp {
+		fsl,pins = <
+			MX7D_PAD_SD2_RESET_B__GPIO5_IO11	0x59
+			MX7D_PAD_SD2_WP__GPIO5_IO10		0x59
+		>;
+	};
 
-		pinctrl_hog: hoggrp {
-			fsl,pins = <
-				MX7D_PAD_ECSPI2_SS0__GPIO4_IO23		0x34  /* bt reg on */
-				MX7D_PAD_EPDC_BDR0__GPIO2_IO28		0x59  /* headphone detect */
-			>;
-		};
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX7D_PAD_ECSPI2_SS0__GPIO4_IO23		0x34  /* bt reg on */
+			MX7D_PAD_EPDC_BDR0__GPIO2_IO28		0x59  /* headphone detect */
+		>;
+	};
 
-		pinctrl_i2c1: i2c1grp {
-			fsl,pins = <
-				MX7D_PAD_I2C1_SDA__I2C1_SDA		0x4000007f
-				MX7D_PAD_I2C1_SCL__I2C1_SCL		0x4000007f
-			>;
-		};
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX7D_PAD_I2C1_SDA__I2C1_SDA		0x4000007f
+			MX7D_PAD_I2C1_SCL__I2C1_SCL		0x4000007f
+		>;
+	};
 
-		pinctrl_i2c2: i2c2grp {
-			fsl,pins = <
-				MX7D_PAD_I2C2_SDA__I2C2_SDA		0x4000007f
-				MX7D_PAD_I2C2_SCL__I2C2_SCL		0x4000007f
-			>;
-		};
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX7D_PAD_I2C2_SDA__I2C2_SDA		0x4000007f
+			MX7D_PAD_I2C2_SCL__I2C2_SCL		0x4000007f
+		>;
+	};
 
-		pinctrl_i2c3: i2c3grp {
-			fsl,pins = <
-				MX7D_PAD_I2C3_SDA__I2C3_SDA		0x4000007f
-				MX7D_PAD_I2C3_SCL__I2C3_SCL		0x4000007f
-			>;
-		};
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX7D_PAD_I2C3_SDA__I2C3_SDA		0x4000007f
+			MX7D_PAD_I2C3_SCL__I2C3_SCL		0x4000007f
+		>;
+	};
 
-		pinctrl_i2c4: i2c4grp {
-			fsl,pins = <
-				MX7D_PAD_SAI1_RX_BCLK__I2C4_SDA		0x4000007f
-				MX7D_PAD_SAI1_RX_SYNC__I2C4_SCL		0x4000007f
-			>;
-		};
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX7D_PAD_SAI1_RX_BCLK__I2C4_SDA		0x4000007f
+			MX7D_PAD_SAI1_RX_SYNC__I2C4_SCL		0x4000007f
+		>;
+	};
 
-		pinctrl_lcdif: lcdifgrp {
-			fsl,pins = <
-				MX7D_PAD_LCD_DATA00__LCD_DATA0		0x79
-				MX7D_PAD_LCD_DATA01__LCD_DATA1		0x79
-				MX7D_PAD_LCD_DATA02__LCD_DATA2		0x79
-				MX7D_PAD_LCD_DATA03__LCD_DATA3		0x79
-				MX7D_PAD_LCD_DATA04__LCD_DATA4		0x79
-				MX7D_PAD_LCD_DATA05__LCD_DATA5		0x79
-				MX7D_PAD_LCD_DATA06__LCD_DATA6		0x79
-				MX7D_PAD_LCD_DATA07__LCD_DATA7		0x79
-				MX7D_PAD_LCD_DATA08__LCD_DATA8		0x79
-				MX7D_PAD_LCD_DATA09__LCD_DATA9		0x79
-				MX7D_PAD_LCD_DATA10__LCD_DATA10		0x79
-				MX7D_PAD_LCD_DATA11__LCD_DATA11		0x79
-				MX7D_PAD_LCD_DATA12__LCD_DATA12		0x79
-				MX7D_PAD_LCD_DATA13__LCD_DATA13		0x79
-				MX7D_PAD_LCD_DATA14__LCD_DATA14		0x79
-				MX7D_PAD_LCD_DATA15__LCD_DATA15		0x79
-				MX7D_PAD_LCD_DATA16__LCD_DATA16		0x79
-				MX7D_PAD_LCD_DATA17__LCD_DATA17		0x79
-				MX7D_PAD_LCD_DATA18__LCD_DATA18		0x79
-				MX7D_PAD_LCD_DATA19__LCD_DATA19		0x79
-				MX7D_PAD_LCD_DATA20__LCD_DATA20		0x79
-				MX7D_PAD_LCD_DATA21__LCD_DATA21		0x79
-				MX7D_PAD_LCD_DATA22__LCD_DATA22		0x79
-				MX7D_PAD_LCD_DATA23__LCD_DATA23		0x79
-				MX7D_PAD_LCD_CLK__LCD_CLK		0x79
-				MX7D_PAD_LCD_ENABLE__LCD_ENABLE		0x79
-				MX7D_PAD_LCD_VSYNC__LCD_VSYNC		0x79
-				MX7D_PAD_LCD_HSYNC__LCD_HSYNC		0x79
-				MX7D_PAD_LCD_RESET__LCD_RESET		0x79
-			>;
-		};
+	pinctrl_lcdif: lcdifgrp {
+		fsl,pins = <
+			MX7D_PAD_LCD_DATA00__LCD_DATA0		0x79
+			MX7D_PAD_LCD_DATA01__LCD_DATA1		0x79
+			MX7D_PAD_LCD_DATA02__LCD_DATA2		0x79
+			MX7D_PAD_LCD_DATA03__LCD_DATA3		0x79
+			MX7D_PAD_LCD_DATA04__LCD_DATA4		0x79
+			MX7D_PAD_LCD_DATA05__LCD_DATA5		0x79
+			MX7D_PAD_LCD_DATA06__LCD_DATA6		0x79
+			MX7D_PAD_LCD_DATA07__LCD_DATA7		0x79
+			MX7D_PAD_LCD_DATA08__LCD_DATA8		0x79
+			MX7D_PAD_LCD_DATA09__LCD_DATA9		0x79
+			MX7D_PAD_LCD_DATA10__LCD_DATA10		0x79
+			MX7D_PAD_LCD_DATA11__LCD_DATA11		0x79
+			MX7D_PAD_LCD_DATA12__LCD_DATA12		0x79
+			MX7D_PAD_LCD_DATA13__LCD_DATA13		0x79
+			MX7D_PAD_LCD_DATA14__LCD_DATA14		0x79
+			MX7D_PAD_LCD_DATA15__LCD_DATA15		0x79
+			MX7D_PAD_LCD_DATA16__LCD_DATA16		0x79
+			MX7D_PAD_LCD_DATA17__LCD_DATA17		0x79
+			MX7D_PAD_LCD_DATA18__LCD_DATA18		0x79
+			MX7D_PAD_LCD_DATA19__LCD_DATA19		0x79
+			MX7D_PAD_LCD_DATA20__LCD_DATA20		0x79
+			MX7D_PAD_LCD_DATA21__LCD_DATA21		0x79
+			MX7D_PAD_LCD_DATA22__LCD_DATA22		0x79
+			MX7D_PAD_LCD_DATA23__LCD_DATA23		0x79
+			MX7D_PAD_LCD_CLK__LCD_CLK		0x79
+			MX7D_PAD_LCD_ENABLE__LCD_ENABLE		0x79
+			MX7D_PAD_LCD_VSYNC__LCD_VSYNC		0x79
+			MX7D_PAD_LCD_HSYNC__LCD_HSYNC		0x79
+			MX7D_PAD_LCD_RESET__LCD_RESET		0x79
+		>;
+	};
 
-		pinctrl_sai1: sai1grp {
-			fsl,pins = <
-				MX7D_PAD_SAI1_MCLK__SAI1_MCLK           0x1f
-				MX7D_PAD_ENET1_RX_CLK__SAI1_TX_BCLK     0x1f
-				MX7D_PAD_ENET1_CRS__SAI1_TX_SYNC	0x1f
-				MX7D_PAD_ENET1_COL__SAI1_TX_DATA0	0x30
-				MX7D_PAD_ENET1_TX_CLK__SAI1_RX_DATA0	0x1f
-			>;
-		};
+	pinctrl_sai1: sai1grp {
+		fsl,pins = <
+			MX7D_PAD_SAI1_MCLK__SAI1_MCLK           0x1f
+			MX7D_PAD_ENET1_RX_CLK__SAI1_TX_BCLK     0x1f
+			MX7D_PAD_ENET1_CRS__SAI1_TX_SYNC	0x1f
+			MX7D_PAD_ENET1_COL__SAI1_TX_DATA0	0x30
+			MX7D_PAD_ENET1_TX_CLK__SAI1_RX_DATA0	0x1f
+		>;
+	};
 
-		pinctrl_sai2: sai2grp {
-			fsl,pins = <
-				MX7D_PAD_SAI2_TX_BCLK__SAI2_TX_BCLK     0x1f
-				MX7D_PAD_SAI2_TX_SYNC__SAI2_TX_SYNC     0x1f
-				MX7D_PAD_SAI2_TX_DATA__SAI2_TX_DATA0    0x30
-				MX7D_PAD_SAI2_RX_DATA__SAI2_RX_DATA0    0x1f
-			>;
-		};
+	pinctrl_sai2: sai2grp {
+		fsl,pins = <
+			MX7D_PAD_SAI2_TX_BCLK__SAI2_TX_BCLK     0x1f
+			MX7D_PAD_SAI2_TX_SYNC__SAI2_TX_SYNC     0x1f
+			MX7D_PAD_SAI2_TX_DATA__SAI2_TX_DATA0    0x30
+			MX7D_PAD_SAI2_RX_DATA__SAI2_RX_DATA0    0x1f
+		>;
+	};
 
-		pinctrl_sai3: sai3grp {
-			fsl,pins = <
-				MX7D_PAD_UART3_TX_DATA__SAI3_TX_BCLK   0x1f
-				MX7D_PAD_UART3_CTS_B__SAI3_TX_SYNC     0x1f
-				MX7D_PAD_UART3_RTS_B__SAI3_TX_DATA0    0x30
-			>;
-		};
+	pinctrl_sai3: sai3grp {
+		fsl,pins = <
+			MX7D_PAD_UART3_TX_DATA__SAI3_TX_BCLK   0x1f
+			MX7D_PAD_UART3_CTS_B__SAI3_TX_SYNC     0x1f
+			MX7D_PAD_UART3_RTS_B__SAI3_TX_DATA0    0x30
+		>;
+	};
 
-		pinctrl_spi4: spi4grp {
-			fsl,pins = <
-				MX7D_PAD_GPIO1_IO09__GPIO1_IO9	0x59
-				MX7D_PAD_GPIO1_IO12__GPIO1_IO12	0x59
-				MX7D_PAD_GPIO1_IO13__GPIO1_IO13	0x59
-			>;
-		};
+	pinctrl_spi4: spi4grp {
+		fsl,pins = <
+			MX7D_PAD_GPIO1_IO09__GPIO1_IO9	0x59
+			MX7D_PAD_GPIO1_IO12__GPIO1_IO12	0x59
+			MX7D_PAD_GPIO1_IO13__GPIO1_IO13	0x59
+		>;
+	};
 
-		pinctrl_tsc2046_pendown: tsc2046_pendown {
-			fsl,pins = <
-				MX7D_PAD_EPDC_BDR1__GPIO2_IO29		0x59
-			>;
-		};
+	pinctrl_tsc2046_pendown: tsc2046-pendowngrp {
+		fsl,pins = <
+			MX7D_PAD_EPDC_BDR1__GPIO2_IO29		0x59
+		>;
+	};
 
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX	0x79
-				MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX	0x79
-			>;
-		};
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX	0x79
+			MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX	0x79
+		>;
+	};
 
-		pinctrl_uart5: uart5grp {
-			fsl,pins = <
-				MX7D_PAD_SAI1_TX_BCLK__UART5_DCE_TX	0x79
-				MX7D_PAD_SAI1_RX_DATA__UART5_DCE_RX	0x79
-				MX7D_PAD_SAI1_TX_SYNC__UART5_DCE_CTS	0x79
-				MX7D_PAD_SAI1_TX_DATA__UART5_DCE_RTS	0x79
-			>;
-		};
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX7D_PAD_SAI1_TX_BCLK__UART5_DCE_TX	0x79
+			MX7D_PAD_SAI1_RX_DATA__UART5_DCE_RX	0x79
+			MX7D_PAD_SAI1_TX_SYNC__UART5_DCE_CTS	0x79
+			MX7D_PAD_SAI1_TX_DATA__UART5_DCE_RTS	0x79
+		>;
+	};
 
-		pinctrl_uart6: uart6grp {
-			fsl,pins = <
-				MX7D_PAD_ECSPI1_MOSI__UART6_DCE_TX	0x79
-				MX7D_PAD_ECSPI1_SCLK__UART6_DCE_RX	0x79
-				MX7D_PAD_ECSPI1_SS0__UART6_DCE_CTS	0x79
-				MX7D_PAD_ECSPI1_MISO__UART6_DCE_RTS	0x79
-			>;
-		};
+	pinctrl_uart6: uart6grp {
+		fsl,pins = <
+			MX7D_PAD_ECSPI1_MOSI__UART6_DCE_TX	0x79
+			MX7D_PAD_ECSPI1_SCLK__UART6_DCE_RX	0x79
+			MX7D_PAD_ECSPI1_SS0__UART6_DCE_CTS	0x79
+			MX7D_PAD_ECSPI1_MISO__UART6_DCE_RTS	0x79
+		>;
+	};
 
-		pinctrl_usdhc1: usdhc1grp {
-			fsl,pins = <
-				MX7D_PAD_SD1_CMD__SD1_CMD		0x59
-				MX7D_PAD_SD1_CLK__SD1_CLK		0x19
-				MX7D_PAD_SD1_DATA0__SD1_DATA0		0x59
-				MX7D_PAD_SD1_DATA1__SD1_DATA1		0x59
-				MX7D_PAD_SD1_DATA2__SD1_DATA2		0x59
-				MX7D_PAD_SD1_DATA3__SD1_DATA3		0x59
-				MX7D_PAD_SD1_CD_B__GPIO5_IO0		0x59 /* CD */
-				MX7D_PAD_SD1_WP__GPIO5_IO1		0x59 /* WP */
-				MX7D_PAD_SD1_RESET_B__GPIO5_IO2		0x59 /* vmmc */
-			>;
-		};
+	pinctrl_usdhc1_gpio: usdhc1-gpiogrp {
+		fsl,pins = <
+			MX7D_PAD_SD1_CD_B__GPIO5_IO0		0x59 /* CD */
+			MX7D_PAD_SD1_WP__GPIO5_IO1		0x59 /* WP */
+			MX7D_PAD_SD1_RESET_B__GPIO5_IO2		0x59 /* vmmc */
+			MX7D_PAD_GPIO1_IO08__SD1_VSELECT	0x59 /* VSELECT */
+		>;
+	};
 
-		pinctrl_usdhc2: usdhc2grp {
-			fsl,pins = <
-				MX7D_PAD_SD2_CMD__SD2_CMD		0x59
-				MX7D_PAD_SD2_CLK__SD2_CLK		0x19
-				MX7D_PAD_SD2_DATA0__SD2_DATA0		0x59
-				MX7D_PAD_SD2_DATA1__SD2_DATA1		0x59
-				MX7D_PAD_SD2_DATA2__SD2_DATA2		0x59
-				MX7D_PAD_SD2_DATA3__SD2_DATA3		0x59
-			>;
-		};
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX7D_PAD_SD1_CMD__SD1_CMD		0x59
+			MX7D_PAD_SD1_CLK__SD1_CLK		0x19
+			MX7D_PAD_SD1_DATA0__SD1_DATA0		0x59
+			MX7D_PAD_SD1_DATA1__SD1_DATA1		0x59
+			MX7D_PAD_SD1_DATA2__SD1_DATA2		0x59
+			MX7D_PAD_SD1_DATA3__SD1_DATA3		0x59
+		>;
+	};
 
-		pinctrl_usdhc2_100mhz: usdhc2grp_100mhz {
-			fsl,pins = <
-				MX7D_PAD_SD2_CMD__SD2_CMD		0x5a
-				MX7D_PAD_SD2_CLK__SD2_CLK		0x1a
-				MX7D_PAD_SD2_DATA0__SD2_DATA0		0x5a
-				MX7D_PAD_SD2_DATA1__SD2_DATA1		0x5a
-				MX7D_PAD_SD2_DATA2__SD2_DATA2		0x5a
-				MX7D_PAD_SD2_DATA3__SD2_DATA3		0x5a
-			>;
-		};
+	pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp {
+		fsl,pins = <
+			MX7D_PAD_SD1_CMD__SD1_CMD		0x5a
+			MX7D_PAD_SD1_CLK__SD1_CLK		0x1a
+			MX7D_PAD_SD1_DATA0__SD1_DATA0		0x5a
+			MX7D_PAD_SD1_DATA1__SD1_DATA1		0x5a
+			MX7D_PAD_SD1_DATA2__SD1_DATA2		0x5a
+			MX7D_PAD_SD1_DATA3__SD1_DATA3		0x5a
+		>;
+	};
 
-		pinctrl_usdhc2_200mhz: usdhc2grp_200mhz {
-			fsl,pins = <
-				MX7D_PAD_SD2_CMD__SD2_CMD		0x5b
-				MX7D_PAD_SD2_CLK__SD2_CLK		0x1b
-				MX7D_PAD_SD2_DATA0__SD2_DATA0		0x5b
-				MX7D_PAD_SD2_DATA1__SD2_DATA1		0x5b
-				MX7D_PAD_SD2_DATA2__SD2_DATA2		0x5b
-				MX7D_PAD_SD2_DATA3__SD2_DATA3		0x5b
-			>;
-		};
+	pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
+		fsl,pins = <
+			MX7D_PAD_SD1_CMD__SD1_CMD		0x5b
+			MX7D_PAD_SD1_CLK__SD1_CLK		0x1b
+			MX7D_PAD_SD1_DATA0__SD1_DATA0		0x5b
+			MX7D_PAD_SD1_DATA1__SD1_DATA1		0x5b
+			MX7D_PAD_SD1_DATA2__SD1_DATA2		0x5b
+			MX7D_PAD_SD1_DATA3__SD1_DATA3		0x5b
+		>;
+	};
 
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX7D_PAD_SD2_CMD__SD2_CMD		0x59
+			MX7D_PAD_SD2_CLK__SD2_CLK		0x19
+			MX7D_PAD_SD2_DATA0__SD2_DATA0		0x59
+			MX7D_PAD_SD2_DATA1__SD2_DATA1		0x59
+			MX7D_PAD_SD2_DATA2__SD2_DATA2		0x59
+			MX7D_PAD_SD2_DATA3__SD2_DATA3		0x59
+		>;
+	};
 
-		pinctrl_usdhc3: usdhc3grp {
-			fsl,pins = <
-				MX7D_PAD_SD3_CMD__SD3_CMD		0x59
-				MX7D_PAD_SD3_CLK__SD3_CLK		0x19
-				MX7D_PAD_SD3_DATA0__SD3_DATA0		0x59
-				MX7D_PAD_SD3_DATA1__SD3_DATA1		0x59
-				MX7D_PAD_SD3_DATA2__SD3_DATA2		0x59
-				MX7D_PAD_SD3_DATA3__SD3_DATA3		0x59
-				MX7D_PAD_SD3_DATA4__SD3_DATA4		0x59
-				MX7D_PAD_SD3_DATA5__SD3_DATA5		0x59
-				MX7D_PAD_SD3_DATA6__SD3_DATA6		0x59
-				MX7D_PAD_SD3_DATA7__SD3_DATA7		0x59
-				MX7D_PAD_SD3_STROBE__SD3_STROBE		0x19
-			>;
-		};
+	pinctrl_usdhc2_100mhz: usdhc2-100mhz-grp {
+		fsl,pins = <
+			MX7D_PAD_SD2_CMD__SD2_CMD		0x5a
+			MX7D_PAD_SD2_CLK__SD2_CLK		0x1a
+			MX7D_PAD_SD2_DATA0__SD2_DATA0		0x5a
+			MX7D_PAD_SD2_DATA1__SD2_DATA1		0x5a
+			MX7D_PAD_SD2_DATA2__SD2_DATA2		0x5a
+			MX7D_PAD_SD2_DATA3__SD2_DATA3		0x5a
+		>;
+	};
 
-		pinctrl_usdhc3_100mhz: usdhc3grp_100mhz {
-			fsl,pins = <
-				MX7D_PAD_SD3_CMD__SD3_CMD		0x5a
-				MX7D_PAD_SD3_CLK__SD3_CLK		0x1a
-				MX7D_PAD_SD3_DATA0__SD3_DATA0		0x5a
-				MX7D_PAD_SD3_DATA1__SD3_DATA1		0x5a
-				MX7D_PAD_SD3_DATA2__SD3_DATA2		0x5a
-				MX7D_PAD_SD3_DATA3__SD3_DATA3		0x5a
-				MX7D_PAD_SD3_DATA4__SD3_DATA4		0x5a
-				MX7D_PAD_SD3_DATA5__SD3_DATA5		0x5a
-				MX7D_PAD_SD3_DATA6__SD3_DATA6		0x5a
-				MX7D_PAD_SD3_DATA7__SD3_DATA7		0x5a
-				MX7D_PAD_SD3_STROBE__SD3_STROBE		0x1a
-			>;
-		};
+	pinctrl_usdhc2_200mhz: usdhc2-200mhz-grp {
+		fsl,pins = <
+			MX7D_PAD_SD2_CMD__SD2_CMD		0x5b
+			MX7D_PAD_SD2_CLK__SD2_CLK		0x1b
+			MX7D_PAD_SD2_DATA0__SD2_DATA0		0x5b
+			MX7D_PAD_SD2_DATA1__SD2_DATA1		0x5b
+			MX7D_PAD_SD2_DATA2__SD2_DATA2		0x5b
+			MX7D_PAD_SD2_DATA3__SD2_DATA3		0x5b
+		>;
+	};
 
-		pinctrl_usdhc3_200mhz: usdhc3grp_200mhz {
-			fsl,pins = <
-				MX7D_PAD_SD3_CMD__SD3_CMD		0x5b
-				MX7D_PAD_SD3_CLK__SD3_CLK		0x1b
-				MX7D_PAD_SD3_DATA0__SD3_DATA0		0x5b
-				MX7D_PAD_SD3_DATA1__SD3_DATA1		0x5b
-				MX7D_PAD_SD3_DATA2__SD3_DATA2		0x5b
-				MX7D_PAD_SD3_DATA3__SD3_DATA3		0x5b
-				MX7D_PAD_SD3_DATA4__SD3_DATA4		0x5b
-				MX7D_PAD_SD3_DATA5__SD3_DATA5		0x5b
-				MX7D_PAD_SD3_DATA6__SD3_DATA6		0x5b
-				MX7D_PAD_SD3_DATA7__SD3_DATA7		0x5b
-				MX7D_PAD_SD3_STROBE__SD3_STROBE		0x1b
-			>;
-		};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX7D_PAD_SD3_CMD__SD3_CMD		0x59
+			MX7D_PAD_SD3_CLK__SD3_CLK		0x19
+			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x59
+			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x59
+			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x59
+			MX7D_PAD_SD3_DATA3__SD3_DATA3		0x59
+			MX7D_PAD_SD3_DATA4__SD3_DATA4		0x59
+			MX7D_PAD_SD3_DATA5__SD3_DATA5		0x59
+			MX7D_PAD_SD3_DATA6__SD3_DATA6		0x59
+			MX7D_PAD_SD3_DATA7__SD3_DATA7		0x59
+			MX7D_PAD_SD3_STROBE__SD3_STROBE		0x19
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhz-grp {
+		fsl,pins = <
+			MX7D_PAD_SD3_CMD__SD3_CMD		0x5a
+			MX7D_PAD_SD3_CLK__SD3_CLK		0x1a
+			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x5a
+			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x5a
+			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x5a
+			MX7D_PAD_SD3_DATA3__SD3_DATA3		0x5a
+			MX7D_PAD_SD3_DATA4__SD3_DATA4		0x5a
+			MX7D_PAD_SD3_DATA5__SD3_DATA5		0x5a
+			MX7D_PAD_SD3_DATA6__SD3_DATA6		0x5a
+			MX7D_PAD_SD3_DATA7__SD3_DATA7		0x5a
+			MX7D_PAD_SD3_STROBE__SD3_STROBE		0x1a
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhz-grp {
+		fsl,pins = <
+			MX7D_PAD_SD3_CMD__SD3_CMD		0x5b
+			MX7D_PAD_SD3_CLK__SD3_CLK		0x1b
+			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x5b
+			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x5b
+			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x5b
+			MX7D_PAD_SD3_DATA3__SD3_DATA3		0x5b
+			MX7D_PAD_SD3_DATA4__SD3_DATA4		0x5b
+			MX7D_PAD_SD3_DATA5__SD3_DATA5		0x5b
+			MX7D_PAD_SD3_DATA6__SD3_DATA6		0x5b
+			MX7D_PAD_SD3_DATA7__SD3_DATA7		0x5b
+			MX7D_PAD_SD3_STROBE__SD3_STROBE		0x1b
+		>;
 	};
 };
 
@@ -859,7 +931,7 @@
 		>;
 	};
 
-	pinctrl_sai3_mclk: sai3grp_mclk {
+	pinctrl_sai3_mclk: sai3-mclk-grp {
 		fsl,pins = <
 			MX7D_PAD_LPSR_GPIO1_IO03__SAI3_MCLK	0x1f
 		>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-smegw01.dts b/arch/arm/boot/dts/nxp/imx/imx7d-smegw01.dts
new file mode 100644
index 000000000000..7ed27c7ad726
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-smegw01.dts
@@ -0,0 +1,468 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+//
+// Copyright (C) 2020 PHYTEC Messtechnik GmbH
+// Author: Jens Lang  <J.Lang@phytec.de>
+// Copyright (C) 2021 Fabio Estevam <festevam@denx.de>
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include "imx7d.dtsi"
+
+/ {
+	model = "Storopack SMEGW01 board";
+	compatible = "storopack,imx7d-smegw01", "fsl,imx7d";
+
+	aliases {
+		ethernet0 = &fec1;
+		ethernet1 = &fec2;
+		mmc0 = &usdhc1;
+		mmc1 = &usdhc3;
+		mmc2 = &usdhc2;
+		rtc0 = &i2c_rtc;
+		rtc1 = &snvs_rtc;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reg_lte_on: regulator-lte-on {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lte_on>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "lte_on";
+		gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	reg_lte_nreset: regulator-lte-nreset {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lte_nreset>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "LTE_nReset";
+		gpio = <&gpio6 21 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	reg_wifi: regulator-wifi {
+		compatible = "regulator-fixed";
+		gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi>;
+		regulator-name = "wifi_reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_wlan_rfkill: regulator-wlan-rfkill {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rfkill>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "wlan_rfkill";
+		gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	reg_usbotg_vbus: regulator-usbotg-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbotg1_pwr_gpio>;
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 05 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	sram@0 {
+		compatible = "microchip,48l640";
+		reg = <0>;
+		spi-max-frequency = <16000000>;
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	assigned-clocks = <&clks IMX7D_ENET1_TIME_ROOT_SRC>,
+			  <&clks IMX7D_ENET1_TIME_ROOT_CLK>;
+	assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
+	assigned-clock-rates = <0>, <100000000>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@1 {
+			compatible = "ethernet-phy-id0022.1622",
+				     "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+		};
+
+		ethphy1: ethernet-phy@2 {
+			compatible = "ethernet-phy-id0022.1622",
+				     "ethernet-phy-ieee802.3-c22";
+			reg = <2>;
+		};
+	};
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2>;
+	assigned-clocks = <&clks IMX7D_ENET2_TIME_ROOT_SRC>,
+			  <&clks IMX7D_ENET2_TIME_ROOT_CLK>;
+	assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
+	assigned-clock-rates = <0>, <100000000>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy1>;
+	fsl,magic-packet;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	i2c_rtc: rtc@52 {
+		compatible = "microcrystal,rv3028";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc_int>;
+		reg = <0x52>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&flexcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	status = "okay";
+};
+
+&flexcan2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1_lpsr>;
+	dr_mode = "otg";
+	vbus-supply = <&reg_usbotg_vbus>;
+	status = "okay";
+};
+
+&usbotg2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg2>;
+	over-current-active-low;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	wakeup-source;
+	keep-power-in-suspend;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	bus-width = <4>;
+	no-1-8-v;
+	non-removable;
+	vmmc-supply = <&reg_wifi>;
+	wakeup-source;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	assigned-clocks = <&clks IMX7D_USDHC3_ROOT_CLK>;
+	assigned-clock-rates = <400000000>;
+	max-frequency = <200000000>;
+	bus-width = <8>;
+	fsl,tuning-step = <1>;
+	non-removable;
+	cap-mmc-highspeed;
+	cap-mmc-hw-reset;
+	mmc-hs200-1_8v;
+	mmc-ddr-1_8v;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX7D_PAD_ECSPI1_SS0__GPIO4_IO19	0x04
+			MX7D_PAD_ECSPI1_SCLK__ECSPI1_SCLK	0x04
+			MX7D_PAD_ECSPI1_MOSI__ECSPI1_MOSI	0x04
+			MX7D_PAD_ECSPI1_MISO__ECSPI1_MISO	0x04
+		>;
+	};
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL 0x5
+			MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0	0x5
+			MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1	0x5
+			MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2	0x5
+			MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3	0x5
+			MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC	0x5
+			MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL 0x5
+			MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0	0x5
+			MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1	0x5
+			MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2	0x5
+			MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3	0x5
+			MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC	0x5
+			MX7D_PAD_GPIO1_IO10__ENET1_MDIO		0x7
+			MX7D_PAD_GPIO1_IO11__ENET1_MDC		0x7
+		>;
+	};
+
+	pinctrl_enet2: enet2grp {
+		fsl,pins = <
+			MX7D_PAD_EPDC_SDCE0__ENET2_RGMII_RX_CTL 0x5
+			MX7D_PAD_EPDC_SDCE1__ENET2_RGMII_RXC	0x5
+			MX7D_PAD_EPDC_SDCLK__ENET2_RGMII_RD0	0x5
+			MX7D_PAD_EPDC_SDLE__ENET2_RGMII_RD1	0x5
+			MX7D_PAD_EPDC_SDOE__ENET2_RGMII_RD2	0x5
+			MX7D_PAD_EPDC_SDSHR__ENET2_RGMII_RD3	0x5
+			MX7D_PAD_EPDC_SDCE2__ENET2_RGMII_TD0	0x5
+			MX7D_PAD_EPDC_SDCE3__ENET2_RGMII_TD1	0x5
+			MX7D_PAD_EPDC_GDCLK__ENET2_RGMII_TD2	0x5
+			MX7D_PAD_EPDC_GDOE__ENET2_RGMII_TD3	0x5
+			MX7D_PAD_EPDC_GDRL__ENET2_RGMII_TX_CTL 0x5
+			MX7D_PAD_EPDC_GDSP__ENET2_RGMII_TXC	0x5
+			MX7D_PAD_GPIO1_IO09__GPIO1_IO9	0x08
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX7D_PAD_I2C2_SCL__I2C2_SCL		0x40000004
+			MX7D_PAD_I2C2_SDA__I2C2_SDA		0x40000004
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX7D_PAD_GPIO1_IO12__FLEXCAN1_RX	0x0b0b0
+			MX7D_PAD_GPIO1_IO13__FLEXCAN1_TX	0x0b0b0
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins = <
+			MX7D_PAD_GPIO1_IO14__FLEXCAN2_RX	0x0b0b0
+			MX7D_PAD_GPIO1_IO15__FLEXCAN2_TX	0x0b0b0
+		>;
+	};
+
+	pinctrl_lte_on: lteongrp {
+		fsl,pins = <
+			MX7D_PAD_ENET1_TX_CLK__GPIO7_IO12	0x17059
+		>;
+	};
+
+	pinctrl_lte_nreset: ltenresetgrp {
+		fsl,pins = <
+			MX7D_PAD_SAI2_RX_DATA__GPIO6_IO21	0x17059
+		>;
+	};
+
+	pinctrl_rfkill: rfkillgrp {
+		fsl,pins = <
+			MX7D_PAD_EPDC_DATA11__GPIO2_IO11	0x17059
+		>;
+	};
+
+	pinctrl_rtc_int: rtcintgrp {
+		fsl,pins = <
+			MX7D_PAD_EPDC_DATA15__GPIO2_IO15	0x17059
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX	0x74
+			MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX	0x7c
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX7D_PAD_UART3_TX_DATA__UART3_DCE_TX	0x7c
+			MX7D_PAD_UART3_RX_DATA__UART3_DCE_RX	0x74
+		>;
+	};
+
+	pinctrl_usbotg1_lpsr: usbotg1grp {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO04__USB_OTG1_OC	0x04
+		>;
+	};
+
+	pinctrl_usbotg1_pwr: usbotg1-pwrgrp {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO05__USB_OTG1_PWR	0x04
+		>;
+	};
+
+	pinctrl_usbotg1_pwr_gpio: usbotg1-pwr-gpiogrp {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO05__GPIO1_IO5	0x04
+		>;
+	};
+
+	pinctrl_usbotg2: usbotg2grp {
+		fsl,pins = <
+			MX7D_PAD_UART3_RTS_B__USB_OTG2_OC	0x5c
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX7D_PAD_SD1_CD_B__GPIO5_IO0		0x59
+			MX7D_PAD_SD1_CMD__SD1_CMD		0x59
+			MX7D_PAD_SD1_CLK__SD1_CLK		0x19
+			MX7D_PAD_SD1_DATA0__SD1_DATA0		0x59
+			MX7D_PAD_SD1_DATA1__SD1_DATA1		0x59
+			MX7D_PAD_SD1_DATA2__SD1_DATA2		0x59
+			MX7D_PAD_SD1_DATA3__SD1_DATA3		0x59
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX7D_PAD_SD2_CLK__SD2_CLK		0x19
+			MX7D_PAD_SD2_CMD__SD2_CMD		0x59
+			MX7D_PAD_SD2_DATA0__SD2_DATA0		0x59
+			MX7D_PAD_SD2_DATA1__SD2_DATA1		0x59
+			MX7D_PAD_SD2_DATA2__SD2_DATA2		0x59
+			MX7D_PAD_SD2_DATA3__SD2_DATA3		0x59
+			MX7D_PAD_SD2_CD_B__SD2_CD_B		0x08
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX7D_PAD_SD3_CMD__SD3_CMD		0x5d
+			MX7D_PAD_SD3_CLK__SD3_CLK		0x1d
+			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x5d
+			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x5d
+			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x5d
+			MX7D_PAD_SD3_DATA3__SD3_DATA3		0x5d
+			MX7D_PAD_SD3_DATA4__SD3_DATA4		0x5d
+			MX7D_PAD_SD3_DATA5__SD3_DATA5		0x5d
+			MX7D_PAD_SD3_DATA6__SD3_DATA6		0x5d
+			MX7D_PAD_SD3_DATA7__SD3_DATA7		0x5d
+			MX7D_PAD_SD3_STROBE__SD3_STROBE	0x1d
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX7D_PAD_SD3_CMD__SD3_CMD		0x5e
+			MX7D_PAD_SD3_CLK__SD3_CLK		0x1e
+			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x5e
+			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x5e
+			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x5e
+			MX7D_PAD_SD3_DATA3__SD3_DATA3		0x5e
+			MX7D_PAD_SD3_DATA4__SD3_DATA4		0x5e
+			MX7D_PAD_SD3_DATA5__SD3_DATA5		0x5e
+			MX7D_PAD_SD3_DATA6__SD3_DATA6		0x5e
+			MX7D_PAD_SD3_DATA7__SD3_DATA7		0x5e
+			MX7D_PAD_SD3_STROBE__SD3_STROBE	0x1e
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX7D_PAD_SD3_CMD__SD3_CMD		0x5f
+			MX7D_PAD_SD3_CLK__SD3_CLK		0x0f
+			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x5f
+			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x5f
+			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x5f
+			MX7D_PAD_SD3_DATA3__SD3_DATA3		0x5f
+			MX7D_PAD_SD3_DATA4__SD3_DATA4		0x5f
+			MX7D_PAD_SD3_DATA5__SD3_DATA5		0x5f
+			MX7D_PAD_SD3_DATA6__SD3_DATA6		0x5f
+			MX7D_PAD_SD3_DATA7__SD3_DATA7		0x5f
+			MX7D_PAD_SD3_STROBE__SD3_STROBE	0x1f
+		>;
+	};
+
+	pinctrl_wifi: wifigrp {
+		fsl,pins = <
+			MX7D_PAD_EPDC_PWR_COM__GPIO2_IO30	0x04
+			MX7D_PAD_SD2_RESET_B__GPIO5_IO11	0x04
+		>;
+	};
+};
+
+&iomuxc_lpsr {
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO00__WDOG1_WDOG_B 0x74
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx7d-tqma7.dtsi b/arch/arm/boot/dts/nxp/imx/imx7d-tqma7.dtsi
index 3ee2017c1ab3..3ee2017c1ab3 100644
--- a/arch/arm/boot/dts/imx7d-tqma7.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-tqma7.dtsi
diff --git a/arch/arm/boot/dts/imx7d-zii-rmu2.dts b/arch/arm/boot/dts/nxp/imx/imx7d-zii-rmu2.dts
index 1065941807e8..8f5566027c25 100644
--- a/arch/arm/boot/dts/imx7d-zii-rmu2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-zii-rmu2.dts
@@ -24,7 +24,7 @@
 		pinctrl-0 = <&pinctrl_leds_debug>;
 		pinctrl-names = "default";
 
-		debug {
+		led-debug {
 			label = "zii:green:debug1";
 			gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
@@ -204,7 +204,7 @@
 	assigned-clock-parents = <&clks IMX7D_PLL_SYS_MAIN_240M_CLK>;
 	status = "okay";
 
-	rave-sp {
+	mcu {
 		compatible = "zii,rave-sp-rdu2";
 		current-speed = <1000000>;
 		#address-cells = <1>;
@@ -350,7 +350,7 @@
 
 &iomuxc_lpsr {
 	pinctrl_enet1_phy_interrupt: enet1phyinterruptgrp {
-		fsl,phy = <
+		fsl,pins = <
 			MX7D_PAD_LPSR_GPIO1_IO02__GPIO1_IO2	0x08
 		>;
 	};
diff --git a/arch/arm/boot/dts/imx7d-zii-rpu2.dts b/arch/arm/boot/dts/nxp/imx/imx7d-zii-rpu2.dts
index 893bd30aa2a3..decc19af3b83 100644
--- a/arch/arm/boot/dts/imx7d-zii-rpu2.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-zii-rpu2.dts
@@ -36,7 +36,7 @@
 		pinctrl-0 = <&pinctrl_leds_debug>;
 		pinctrl-names = "default";
 
-		debug {
+		led-debug {
 			label = "zii:green:debug1";
 			gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
@@ -607,7 +607,7 @@
 	assigned-clock-parents = <&clks IMX7D_PLL_SYS_MAIN_240M_CLK>;
 	status = "okay";
 
-	rave-sp {
+	mcu {
 		compatible = "zii,rave-sp-rdu2";
 		current-speed = <1000000>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/imx7d.dtsi b/arch/arm/boot/dts/nxp/imx/imx7d.dtsi
index f8cba47536a0..d961c61a93af 100644
--- a/arch/arm/boot/dts/imx7d.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx7d.dtsi
@@ -48,7 +48,7 @@
 
 		opp-792000000 {
 			opp-hz = /bits/ 64 <792000000>;
-			opp-microvolt = <1000000>;
+			opp-microvolt = <1000000 950000 1250000>;
 			clock-latency-ns = <150000>;
 			opp-supported-hw = <0xd>, <0x7>;
 			opp-suspend;
@@ -56,7 +56,7 @@
 
 		opp-996000000 {
 			opp-hz = /bits/ 64 <996000000>;
-			opp-microvolt = <1100000>;
+			opp-microvolt = <1100000 1045000 1250000>;
 			clock-latency-ns = <150000>;
 			opp-supported-hw = <0xc>, <0x7>;
 			opp-suspend;
@@ -64,7 +64,7 @@
 
 		opp-1200000000 {
 			opp-hz = /bits/ 64 <1200000000>;
-			opp-microvolt = <1225000>;
+			opp-microvolt = <1225000 1200000 1250000>;
 			clock-latency-ns = <150000>;
 			opp-supported-hw = <0x8>, <0x3>;
 			opp-suspend;
@@ -78,7 +78,7 @@
 		#phy-cells = <0>;
 	};
 
-	soc {
+	soc: soc {
 		etm@3007d000 {
 			compatible = "arm,coresight-etm3x", "arm,primecell";
 			reg = <0x3007d000 0x1000>;
@@ -165,6 +165,15 @@
 		  reg = <0x306d0000 0x10000>;
 		  status = "disabled";
 	};
+
+	pxp: pxp@30700000 {
+		compatible = "fsl,imx7d-pxp";
+		reg = <0x30700000 0x10000>;
+		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clks IMX7D_PXP_CLK>;
+		clock-names = "axi";
+	};
 };
 
 &aips3 {
@@ -208,9 +217,6 @@
 };
 
 &ca_funnel_in_ports {
-	#address-cells = <1>;
-	#size-cells = <0>;
-
 	port@1 {
 		reg = <1>;
 		ca_funnel_in_port1: endpoint {
diff --git a/arch/arm/boot/dts/nxp/imx/imx7s-colibri-aster.dts b/arch/arm/boot/dts/nxp/imx/imx7s-colibri-aster.dts
new file mode 100644
index 000000000000..58ebb02d948a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7s-colibri-aster.dts
@@ -0,0 +1,36 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2017-2022 Toradex
+ *
+ */
+
+/dts-v1/;
+#include "imx7s-colibri.dtsi"
+#include "imx7-colibri-aster.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7S on Aster Carrier Board";
+	compatible = "toradex,colibri-imx7s-aster",
+		     "toradex,colibri-imx7s",
+		     "fsl,imx7s";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7s-colibri-eval-v3.dts b/arch/arm/boot/dts/nxp/imx/imx7s-colibri-eval-v3.dts
new file mode 100644
index 000000000000..38de76630d6a
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7s-colibri-eval-v3.dts
@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2016-2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7s-colibri.dtsi"
+#include "imx7-colibri-eval-v3.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7S on Colibri Evaluation Board V3";
+	compatible = "toradex,colibri-imx7s-eval-v3",
+		     "toradex,colibri-imx7s",
+		     "fsl,imx7s";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+/*
+ * The Atmel maxtouch controller uses SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2, pwm3.
+ * So if you enable following capacitive touch controller, disable pwm2/pwm3 first.
+ */
+&atmel_mxt_ts {
+	status = "disabled";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+/* Colibri PWM<B> */
+&pwm2 {
+	/* The pwm2 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri PWM<C> */
+&pwm3 {
+	/* The pwm3 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7s-colibri-iris-v2.dts b/arch/arm/boot/dts/nxp/imx/imx7s-colibri-iris-v2.dts
new file mode 100644
index 000000000000..72b5c17ab1ab
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7s-colibri-iris-v2.dts
@@ -0,0 +1,78 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7s-colibri.dtsi"
+#include "imx7-colibri-iris-v2.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7S on Iris V2 Carrier Board";
+	compatible = "toradex,colibri-imx7s-iris-v2",
+		     "toradex,colibri-imx7s",
+		     "fsl,imx7s";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&gpio2 {
+	/*
+	 * This switches the LVDS transceiver to VESA color mapping mode.
+	 */
+	lvds-color-map-hog {
+		gpio-hog;
+		gpios = <13 GPIO_ACTIVE_HIGH>; /* SODIMM 95 */
+		line-name = "LVDS_COLOR_MAP";
+		output-low;
+	};
+};
+
+&gpio7 {
+	/*
+	 * This switches the LVDS transceiver to the 24-bit RGB mode.
+	 */
+	lvds-rgb-mode-hog {
+		gpio-hog;
+		gpios = <2 GPIO_ACTIVE_HIGH>; /* SODIMM 63 */
+		line-name = "LVDS_RGB_MODE";
+		output-low;
+	};
+
+	/*
+	 * This switches the LVDS transceiver to the single-channel
+	 * output mode.
+	 */
+	lvds-ch-mode-hog {
+		gpio-hog;
+		gpios = <3 GPIO_ACTIVE_HIGH>; /* SODIMM 55 */
+		line-name = "LVDS_CH_MODE";
+		output-high;
+	};
+
+	/* This turns the LVDS transceiver on */
+	lvds-power-on-hog {
+		gpio-hog;
+		gpios = <11 GPIO_ACTIVE_HIGH>; /* SODIMM 99 */
+		line-name = "LVDS_POWER_ON";
+		output-high;
+	};
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imx7s-colibri-iris.dts b/arch/arm/boot/dts/nxp/imx/imx7s-colibri-iris.dts
new file mode 100644
index 000000000000..26ba72c17feb
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx7s-colibri-iris.dts
@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7s-colibri.dtsi"
+#include "imx7-colibri-iris.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7S on Iris Carrier Board";
+	compatible = "toradex,colibri-imx7s-iris",
+		     "toradex,colibri-imx7s",
+		     "fsl,imx7s";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+/*
+ * The Atmel maxtouch controller uses SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2, pwm3.
+ * So if you enable following capacitive touch controller, disable pwm2/pwm3 first.
+ */
+&atmel_mxt_ts {
+	status = "disabled";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+/* Colibri PWM<B> */
+&pwm2 {
+	/* The pwm2 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri PWM<C> */
+&pwm3 {
+	/* The pwm3 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx7s-colibri.dtsi b/arch/arm/boot/dts/nxp/imx/imx7s-colibri.dtsi
index 94de220a5965..ef51395d3537 100644
--- a/arch/arm/boot/dts/imx7s-colibri.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx7s-colibri.dtsi
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2016-2020 Toradex
+ * Copyright 2016-2022 Toradex
  */
 
 #include "imx7s.dtsi"
@@ -13,6 +13,7 @@
 	};
 };
 
+/* NAND */
 &gpmi {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx7s-mba7.dts b/arch/arm/boot/dts/nxp/imx/imx7s-mba7.dts
index 8e4cf589c92c..8e4cf589c92c 100644
--- a/arch/arm/boot/dts/imx7s-mba7.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7s-mba7.dts
diff --git a/arch/arm/boot/dts/imx7s-tqma7.dtsi b/arch/arm/boot/dts/nxp/imx/imx7s-tqma7.dtsi
index 7a190fdb2d30..7a190fdb2d30 100644
--- a/arch/arm/boot/dts/imx7s-tqma7.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx7s-tqma7.dtsi
diff --git a/arch/arm/boot/dts/imx7s-warp.dts b/arch/arm/boot/dts/nxp/imx/imx7s-warp.dts
index e8734d218b9d..56dedd4fb8f0 100644
--- a/arch/arm/boot/dts/imx7s-warp.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7s-warp.dts
@@ -23,7 +23,7 @@
 		pinctrl-0 = <&pinctrl_gpio>;
 		autorepeat;
 
-		back {
+		key-back {
 			label = "Back";
 			gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_BACK>;
@@ -31,30 +31,6 @@
 		};
 	};
 
-	reg_brcm: regulator-brcm {
-		compatible = "regulator-fixed";
-		enable-active-high;
-		gpio = <&gpio5 10 GPIO_ACTIVE_HIGH>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_brcm_reg>;
-		regulator-name = "brcm_reg";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		startup-delay-us = <200000>;
-	};
-
-	reg_bt: regulator-bt {
-		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_bt_reg>;
-		enable-active-high;
-		gpio = <&gpio5 17 GPIO_ACTIVE_HIGH>;
-		regulator-name = "bt_reg";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-	};
-
 	reg_peri_3p15v: regulator-peri-3p15v {
 		compatible = "regulator-fixed";
 		regulator-name = "peri_3p15v_reg";
@@ -63,6 +39,14 @@
 		regulator-always-on;
 	};
 
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_brcm_reg>;
+		post-power-on-delay-ms = <200>;
+		reset-gpios = <&gpio5 10 GPIO_ACTIVE_LOW>;
+	};
+
 	sound {
 		compatible = "simple-audio-card";
 		simple-audio-card,name = "imx7-sgtl5000";
@@ -94,7 +78,7 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	pmic: pfuze3000@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze3000";
 		reg = <0x08>;
 
@@ -210,6 +194,7 @@
 				remote-endpoint = <&mipi_from_sensor>;
 				clock-lanes = <0>;
 				data-lanes = <1>;
+				link-frequencies = /bits/ 64 <330000000>;
 			};
 		};
 	};
@@ -287,6 +272,14 @@
 	assigned-clock-parents = <&clks IMX7D_PLL_SYS_MAIN_240M_CLK>;
 	uart-has-rtscts;
 	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm4345c5";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_bt_reg>;
+		shutdown-gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>;
+		max-speed = <3000000>;
+	};
 };
 
 &uart6 {
@@ -304,14 +297,21 @@
 };
 
 &usdhc1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc1>;
 	bus-width = <4>;
 	keep-power-in-suspend;
 	no-1-8-v;
 	non-removable;
-	vmmc-supply = <&reg_brcm>;
+	mmc-pwrseq = <&sdio_pwrseq>;
 	status = "okay";
+
+	wifi@0 {
+		compatible = "brcm,bcm43455-fmac", "brcm,bcm4329-fmac";
+		reg = <0>;
+	};
 };
 
 &usdhc3 {
@@ -458,7 +458,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_100mhz: usdhc3grp_100mhz {
+	pinctrl_usdhc3_100mhz: usdhc3-100mhz-grp {
 		fsl,pins = <
 			MX7D_PAD_SD3_CMD__SD3_CMD		0x5a
 			MX7D_PAD_SD3_CLK__SD3_CLK		0x1a
@@ -474,7 +474,7 @@
 		>;
 	};
 
-	pinctrl_usdhc3_200mhz: usdhc3grp_200mhz {
+	pinctrl_usdhc3_200mhz: usdhc3-200mhz-grp {
 		fsl,pins = <
 			MX7D_PAD_SD3_CMD__SD3_CMD		0x5b
 			MX7D_PAD_SD3_CLK__SD3_CLK		0x1b
diff --git a/arch/arm/boot/dts/imx7s.dtsi b/arch/arm/boot/dts/nxp/imx/imx7s.dtsi
index 5af6d58666f4..9235dd7e93bb 100644
--- a/arch/arm/boot/dts/imx7s.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx7s.dtsi
@@ -73,7 +73,6 @@
 			device_type = "cpu";
 			reg = <0>;
 			clock-frequency = <792000000>;
-			clock-latency = <61036>; /* two CLK32 periods */
 			clocks = <&clks IMX7D_CLK_ARM>;
 			cpu-idle-states = <&cpu_sleep_wait>;
 			operating-points-v2 = <&cpu0_opp_table>;
@@ -120,6 +119,7 @@
 		compatible = "usb-nop-xceiv";
 		clocks = <&clks IMX7D_USB_HSIC_ROOT_CLK>;
 		clock-names = "main_clk";
+		power-domains = <&pgc_hsic_phy>;
 		#phy-cells = <0>;
 	};
 
@@ -175,13 +175,50 @@
 			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
 	};
 
-	soc {
+	video_mux: csi-mux {
+		compatible = "video-mux";
+		mux-controls = <&mux 0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+
+		port@0 {
+			reg = <0>;
+		};
+
+		port@1 {
+			reg = <1>;
+
+			csi_mux_from_mipi_vc0: endpoint {
+				remote-endpoint = <&mipi_vc0_to_csi_mux>;
+			};
+		};
+
+		port@2 {
+			reg = <2>;
+
+			csi_mux_to_csi: endpoint {
+				remote-endpoint = <&csi_from_csi_mux>;
+			};
+		};
+	};
+
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
 		interrupt-parent = <&gpc>;
 		ranges;
 
+		ocram: sram@900000 {
+			compatible = "mmio-sram";
+			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&clks IMX7D_OCRAM_CLK>;
+		};
+
 		funnel@30041000 {
 			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
 			reg = <0x30041000 0x1000>;
@@ -189,7 +226,11 @@
 			clock-names = "apb_pclk";
 
 			ca_funnel_in_ports: in-ports {
-				port {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
 					ca_funnel_in_port0: endpoint {
 						remote-endpoint = <&etm0_out_port>;
 					};
@@ -446,14 +487,14 @@
 				status = "disabled";
 			};
 
-			iomuxc_lpsr: iomuxc-lpsr@302c0000 {
+			iomuxc_lpsr: pinctrl@302c0000 {
 				compatible = "fsl,imx7d-iomuxc-lpsr";
 				reg = <0x302c0000 0x10000>;
 				fsl,input-sel = <&iomuxc>;
 			};
 
 			gpt1: timer@302d0000 {
-				compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
+				compatible = "fsl,imx7d-gpt", "fsl,imx6dl-gpt";
 				reg = <0x302d0000 0x10000>;
 				interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX7D_GPT1_ROOT_CLK>,
@@ -462,7 +503,7 @@
 			};
 
 			gpt2: timer@302e0000 {
-				compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
+				compatible = "fsl,imx7d-gpt", "fsl,imx6dl-gpt";
 				reg = <0x302e0000 0x10000>;
 				interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX7D_GPT2_ROOT_CLK>,
@@ -472,7 +513,7 @@
 			};
 
 			gpt3: timer@302f0000 {
-				compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
+				compatible = "fsl,imx7d-gpt", "fsl,imx6dl-gpt";
 				reg = <0x302f0000 0x10000>;
 				interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX7D_GPT3_ROOT_CLK>,
@@ -482,7 +523,7 @@
 			};
 
 			gpt4: timer@30300000 {
-				compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
+				compatible = "fsl,imx7d-gpt", "fsl,imx6dl-gpt";
 				reg = <0x30300000 0x10000>;
 				interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX7D_GPT4_ROOT_CLK>,
@@ -512,37 +553,9 @@
 
 				mux: mux-controller {
 					compatible = "mmio-mux";
-					#mux-control-cells = <0>;
+					#mux-control-cells = <1>;
 					mux-reg-masks = <0x14 0x00000010>;
 				};
-
-				video_mux: csi-mux {
-					compatible = "video-mux";
-					mux-controls = <&mux 0>;
-					#address-cells = <1>;
-					#size-cells = <0>;
-					status = "disabled";
-
-					port@0 {
-						reg = <0>;
-					};
-
-					port@1 {
-						reg = <1>;
-
-						csi_mux_from_mipi_vc0: endpoint {
-							remote-endpoint = <&mipi_vc0_to_csi_mux>;
-						};
-					};
-
-					port@2 {
-						reg = <2>;
-
-						csi_mux_to_csi: endpoint {
-							remote-endpoint = <&csi_from_csi_mux>;
-						};
-					};
-				};
 			};
 
 			ocotp: efuse@30350000 {
@@ -604,6 +617,7 @@
 					nvmem-cells = <&tempmon_calib>,	<&fuse_grade>;
 					nvmem-cell-names = "calib", "temp_grade";
 					clocks = <&clks IMX7D_PLL_SYS_MAIN_CLK>;
+					#thermal-sensor-cells = <0>;
 				};
 			};
 
@@ -621,6 +635,15 @@
 					clock-names = "snvs-rtc";
 				};
 
+				snvs_poweroff: snvs-poweroff {
+					compatible = "syscon-poweroff";
+					regmap = <&snvs>;
+					offset = <0x38>;
+					value = <0x60>;
+					mask = <0x60>;
+					status = "disabled";
+				};
+
 				snvs_pwrkey: snvs-powerkey {
 					compatible = "fsl,sec-v4.0-pwrkey";
 					regmap = <&snvs>;
@@ -657,7 +680,6 @@
 				interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <3>;
 				interrupt-parent = <&intc>;
-				#power-domain-cells = <1>;
 
 				pgc {
 					#address-cells = <1>;
@@ -720,6 +742,8 @@
 				clocks = <&clks IMX7D_ECSPI4_ROOT_CLK>,
 					<&clks IMX7D_ECSPI4_ROOT_CLK>;
 				clock-names = "ipg", "per";
+				dma-names = "rx", "tx";
+				dmas = <&sdma 6 7 1>, <&sdma 7 7 2>;
 				status = "disabled";
 			};
 
@@ -799,10 +823,8 @@
 				compatible = "fsl,imx7-csi";
 				reg = <0x30710000 0x10000>;
 				interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clks IMX7D_CLK_DUMMY>,
-					 <&clks IMX7D_CSI_MCLK_ROOT_CLK>,
-					 <&clks IMX7D_CLK_DUMMY>;
-				clock-names = "axi", "mclk", "dcic";
+				clocks = <&clks IMX7D_CSI_MCLK_ROOT_CLK>;
+				clock-names = "mclk";
 				status = "disabled";
 
 				port {
@@ -813,7 +835,7 @@
 			};
 
 			lcdif: lcdif@30730000 {
-				compatible = "fsl,imx7d-lcdif", "fsl,imx28-lcdif";
+				compatible = "fsl,imx7d-lcdif", "fsl,imx6sx-lcdif";
 				reg = <0x30730000 0x10000>;
 				interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX7D_LCDIF_PIXEL_ROOT_CLK>,
@@ -852,6 +874,26 @@
 					};
 				};
 			};
+
+			mipi_dsi: dsi@30760000 {
+				compatible = "fsl,imx7d-mipi-dsim", "fsl,imx8mm-mipi-dsim";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x30760000 0x400>;
+				clocks = <&clks IMX7D_MIPI_DSI_ROOT_CLK>,
+					 <&clks IMX7D_MIPI_DPHY_ROOT_CLK>;
+				clock-names = "bus_clk", "sclk_mipi";
+				assigned-clocks = <&clks IMX7D_MIPI_DSI_ROOT_SRC>,
+						  <&clks IMX7D_PLL_SYS_PFD5_CLK>;
+				assigned-clock-parents = <&clks IMX7D_PLL_SYS_PFD5_CLK>;
+				assigned-clock-rates = <0>, <333000000>;
+				power-domains = <&pgc_mipi_phy>;
+				interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+				samsung,burst-clock-frequency = <891000000>;
+				samsung,esc-clock-frequency = <20000000>;
+				samsung,pll-clock-frequency = <24000000>;
+				status = "disabled";
+			};
 		};
 
 		aips3: bus@30800000 {
@@ -877,6 +919,8 @@
 					clocks = <&clks IMX7D_ECSPI1_ROOT_CLK>,
 						<&clks IMX7D_ECSPI1_ROOT_CLK>;
 					clock-names = "ipg", "per";
+					dma-names = "rx", "tx";
+					dmas = <&sdma 0 7 1>, <&sdma 1 7 2>;
 					status = "disabled";
 				};
 
@@ -889,6 +933,8 @@
 					clocks = <&clks IMX7D_ECSPI2_ROOT_CLK>,
 						<&clks IMX7D_ECSPI2_ROOT_CLK>;
 					clock-names = "ipg", "per";
+					dma-names = "rx", "tx";
+					dmas = <&sdma 2 7 1>, <&sdma 3 7 2>;
 					status = "disabled";
 				};
 
@@ -901,6 +947,8 @@
 					clocks = <&clks IMX7D_ECSPI3_ROOT_CLK>,
 						<&clks IMX7D_ECSPI3_ROOT_CLK>;
 					clock-names = "ipg", "per";
+					dma-names = "rx", "tx";
+					dmas = <&sdma 4 7 1>, <&sdma 5 7 2>;
 					status = "disabled";
 				};
 
@@ -1153,7 +1201,6 @@
 				compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
 				reg = <0x30b30000 0x200>;
 				interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
-				power-domains = <&pgc_hsic_phy>;
 				clocks = <&clks IMX7D_USB_CTRL_CLK>;
 				fsl,usbphy = <&usbphynop3>;
 				fsl,usbmisc = <&usbmisc3 0>;
@@ -1184,6 +1231,8 @@
 					<&clks IMX7D_USDHC1_ROOT_CLK>;
 				clock-names = "ipg", "ahb", "per";
 				bus-width = <4>;
+				fsl,tuning-step = <2>;
+				fsl,tuning-start-tap = <20>;
 				status = "disabled";
 			};
 
@@ -1196,6 +1245,8 @@
 					<&clks IMX7D_USDHC2_ROOT_CLK>;
 				clock-names = "ipg", "ahb", "per";
 				bus-width = <4>;
+				fsl,tuning-step = <2>;
+				fsl,tuning-start-tap = <20>;
 				status = "disabled";
 			};
 
@@ -1208,6 +1259,8 @@
 					<&clks IMX7D_USDHC3_ROOT_CLK>;
 				clock-names = "ipg", "ahb", "per";
 				bus-width = <4>;
+				fsl,tuning-step = <2>;
+				fsl,tuning-start-tap = <20>;
 				status = "disabled";
 			};
 
@@ -1224,7 +1277,7 @@
 				status = "disabled";
 			};
 
-			sdma: sdma@30bd0000 {
+			sdma: dma-controller@30bd0000 {
 				compatible = "fsl,imx7d-sdma", "fsl,imx35-sdma";
 				reg = <0x30bd0000 0x10000>;
 				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
@@ -1257,23 +1310,22 @@
 			};
 		};
 
-		dma_apbh: dma-apbh@33000000 {
+		dma_apbh: dma-controller@33000000 {
 			compatible = "fsl,imx7d-dma-apbh", "fsl,imx28-dma-apbh";
 			reg = <0x33000000 0x2000>;
 			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3";
 			#dma-cells = <1>;
 			dma-channels = <4>;
 			clocks = <&clks IMX7D_NAND_USDHC_BUS_RAWNAND_CLK>;
 		};
 
-		gpmi: nand-controller@33002000{
+		gpmi: nand-controller@33002000 {
 			compatible = "fsl,imx7d-gpmi-nand";
 			#address-cells = <1>;
-			#size-cells = <1>;
+			#size-cells = <0>;
 			reg = <0x33002000 0x2000>, <0x33004000 0x4000>;
 			reg-names = "gpmi-nand", "bch";
 			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/imx7ulp-com.dts b/arch/arm/boot/dts/nxp/imx/imx7ulp-com.dts
index d76fea3b35c6..d76fea3b35c6 100644
--- a/arch/arm/boot/dts/imx7ulp-com.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7ulp-com.dts
diff --git a/arch/arm/boot/dts/imx7ulp-evk.dts b/arch/arm/boot/dts/nxp/imx/imx7ulp-evk.dts
index eff51e113db4..eff51e113db4 100644
--- a/arch/arm/boot/dts/imx7ulp-evk.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7ulp-evk.dts
diff --git a/arch/arm/boot/dts/imx7ulp-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imx7ulp-pinfunc.h
index c0148d79b62d..c0148d79b62d 100644
--- a/arch/arm/boot/dts/imx7ulp-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imx7ulp-pinfunc.h
diff --git a/arch/arm/boot/dts/imx7ulp.dtsi b/arch/arm/boot/dts/nxp/imx/imx7ulp.dtsi
index bcec98b96411..880b9a4f32b0 100644
--- a/arch/arm/boot/dts/imx7ulp.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx7ulp.dtsi
@@ -189,7 +189,7 @@
 		};
 
 		usbotg1: usb@40330000 {
-			compatible = "fsl,imx7ulp-usb", "fsl,imx6ul-usb";
+			compatible = "fsl,imx7ulp-usb", "fsl,imx6ul-usb", "fsl,imx27-usb";
 			reg = <0x40330000 0x200>;
 			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&pcc2 IMX7ULP_CLK_USB0>;
@@ -202,21 +202,23 @@
 		};
 
 		usbmisc1: usbmisc@40330200 {
-			compatible = "fsl,imx7ulp-usbmisc", "fsl,imx7d-usbmisc";
+			compatible = "fsl,imx7ulp-usbmisc", "fsl,imx7d-usbmisc",
+				     "fsl,imx6q-usbmisc";
 			#index-cells = <1>;
 			reg = <0x40330200 0x200>;
 		};
 
 		usbphy1: usb-phy@40350000 {
-			compatible = "fsl,imx7ulp-usbphy", "fsl,imx6ul-usbphy";
+			compatible = "fsl,imx7ulp-usbphy";
 			reg = <0x40350000 0x1000>;
 			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&pcc2 IMX7ULP_CLK_USB_PHY>;
 			#phy-cells = <0>;
+			nxp,sim = <&sim>;
 		};
 
 		usdhc0: mmc@40370000 {
-			compatible = "fsl,imx7ulp-usdhc", "fsl,imx6sx-usdhc";
+			compatible = "fsl,imx7ulp-usdhc";
 			reg = <0x40370000 0x10000>;
 			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&scg1 IMX7ULP_CLK_NIC1_BUS_DIV>,
@@ -230,7 +232,7 @@
 		};
 
 		usdhc1: mmc@40380000 {
-			compatible = "fsl,imx7ulp-usdhc", "fsl,imx6sx-usdhc";
+			compatible = "fsl,imx7ulp-usdhc";
 			reg = <0x40380000 0x10000>;
 			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&scg1 IMX7ULP_CLK_NIC1_BUS_DIV>,
@@ -328,8 +330,9 @@
 			compatible = "fsl,imx7ulp-lpi2c";
 			reg = <0x40a40000 0x10000>;
 			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&pcc3 IMX7ULP_CLK_LPI2C6>;
-			clock-names = "ipg";
+			clocks = <&pcc3 IMX7ULP_CLK_LPI2C6>,
+				 <&scg1 IMX7ULP_CLK_NIC1_BUS_DIV>;
+			clock-names = "per", "ipg";
 			assigned-clocks = <&pcc3 IMX7ULP_CLK_LPI2C6>;
 			assigned-clock-parents = <&scg1 IMX7ULP_CLK_FIRC>;
 			assigned-clock-rates = <48000000>;
@@ -340,8 +343,9 @@
 			compatible = "fsl,imx7ulp-lpi2c";
 			reg = <0x40a50000 0x10000>;
 			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&pcc3 IMX7ULP_CLK_LPI2C7>;
-			clock-names = "ipg";
+			clocks = <&pcc3 IMX7ULP_CLK_LPI2C7>,
+				 <&scg1 IMX7ULP_CLK_NIC1_BUS_DIV>;
+			clock-names = "per", "ipg";
 			assigned-clocks = <&pcc3 IMX7ULP_CLK_LPI2C7>;
 			assigned-clock-parents = <&scg1 IMX7ULP_CLK_FIRC>;
 			assigned-clock-rates = <48000000>;
@@ -395,6 +399,7 @@
 				 <&pcc3 IMX7ULP_CLK_PCTLC>;
 			clock-names = "gpio", "port";
 			gpio-ranges = <&iomuxc1 0 0 20>;
+			ngpios = <20>;
 		};
 
 		gpio_ptd: gpio@40af0000 {
@@ -409,6 +414,7 @@
 				 <&pcc3 IMX7ULP_CLK_PCTLD>;
 			clock-names = "gpio", "port";
 			gpio-ranges = <&iomuxc1 0 32 12>;
+			ngpios = <12>;
 		};
 
 		gpio_pte: gpio@40b00000 {
@@ -423,6 +429,7 @@
 				 <&pcc3 IMX7ULP_CLK_PCTLE>;
 			clock-names = "gpio", "port";
 			gpio-ranges = <&iomuxc1 0 64 16>;
+			ngpios = <16>;
 		};
 
 		gpio_ptf: gpio@40b10000 {
@@ -437,6 +444,7 @@
 				 <&pcc3 IMX7ULP_CLK_PCTLF>;
 			clock-names = "gpio", "port";
 			gpio-ranges = <&iomuxc1 0 96 20>;
+			ngpios = <20>;
 		};
 	};
 
@@ -456,6 +464,8 @@
 			compatible = "fsl,imx7ulp-ocotp", "syscon";
 			reg = <0x410a6000 0x4000>;
 			clocks = <&scg1 IMX7ULP_CLK_DUMMY>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/nxp/imx/imxrt1050-evk.dts b/arch/arm/boot/dts/nxp/imx/imxrt1050-evk.dts
new file mode 100644
index 000000000000..6a9c10decf52
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imxrt1050-evk.dts
@@ -0,0 +1,72 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019
+ * Author(s): Giulio Benetti <giulio.benetti@benettiengineering.com>
+ */
+
+/dts-v1/;
+#include "imxrt1050.dtsi"
+#include "imxrt1050-pinfunc.h"
+
+/ {
+	model = "NXP IMXRT1050-evk board";
+	compatible = "fsl,imxrt1050-evk", "fsl,imxrt1050";
+
+	chosen {
+		stdout-path = &lpuart1;
+	};
+
+	aliases {
+		gpio0 = &gpio1;
+		gpio1 = &gpio2;
+		gpio2 = &gpio3;
+		gpio3 = &gpio4;
+		gpio4 = &gpio5;
+		mmc0 = &usdhc1;
+		serial0 = &lpuart1;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x2000000>;
+	};
+};
+
+&lpuart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart1>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl_lpuart1: lpuart1grp {
+		fsl,pins = <
+			MXRT1050_IOMUXC_GPIO_AD_B0_12_LPUART1_TXD	0xf1
+			MXRT1050_IOMUXC_GPIO_AD_B0_13_LPUART1_RXD	0xf1
+		>;
+	};
+
+	pinctrl_usdhc0: usdhc0grp {
+		fsl,pins = <
+			MXRT1050_IOMUXC_GPIO_B1_12_USDHC1_CD_B		0x1B000
+			MXRT1050_IOMUXC_GPIO_B1_14_USDHC1_VSELECT	0xB069
+			MXRT1050_IOMUXC_GPIO_SD_B0_00_USDHC1_CMD	0x17061
+			MXRT1050_IOMUXC_GPIO_SD_B0_01_USDHC1_CLK	0x17061
+			MXRT1050_IOMUXC_GPIO_SD_B0_05_USDHC1_DATA3	0x17061
+			MXRT1050_IOMUXC_GPIO_SD_B0_04_USDHC1_DATA2	0x17061
+			MXRT1050_IOMUXC_GPIO_SD_B0_03_USDHC1_DATA1	0x17061
+			MXRT1050_IOMUXC_GPIO_SD_B0_02_USDHC1_DATA0	0x17061
+		>;
+	};
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc0>;
+	pinctrl-1 = <&pinctrl_usdhc0>;
+	pinctrl-2 = <&pinctrl_usdhc0>;
+	pinctrl-3 = <&pinctrl_usdhc0>;
+	cd-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imxrt1050-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imxrt1050-pinfunc.h
index 22c14a3262ad..22c14a3262ad 100644
--- a/arch/arm/boot/dts/imxrt1050-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/imx/imxrt1050-pinfunc.h
diff --git a/arch/arm/boot/dts/nxp/imx/imxrt1050.dtsi b/arch/arm/boot/dts/nxp/imx/imxrt1050.dtsi
new file mode 100644
index 000000000000..b0bad0d1ba36
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imxrt1050.dtsi
@@ -0,0 +1,160 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019
+ * Author(s): Giulio Benetti <giulio.benetti@benettiengineering.com>
+ */
+
+#include "../../armv7-m.dtsi"
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/imxrt1050-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	clocks {
+		osc: osc {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <24000000>;
+		};
+
+		osc3M: osc3M {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <3000000>;
+		};
+	};
+
+	soc {
+		lpuart1: serial@40184000 {
+			compatible = "fsl,imxrt1050-lpuart", "fsl,imx7ulp-lpuart";
+			reg = <0x40184000 0x4000>;
+			interrupts = <20>;
+			clocks = <&clks IMXRT1050_CLK_LPUART1>;
+			clock-names = "ipg";
+			status = "disabled";
+		};
+
+		iomuxc: pinctrl@401f8000 {
+			compatible = "fsl,imxrt1050-iomuxc";
+			reg = <0x401f8000 0x4000>;
+			fsl,mux_mask = <0x7>;
+		};
+
+		anatop: anatop@400d8000 {
+			compatible = "fsl,imxrt-anatop";
+			reg = <0x400d8000 0x4000>;
+		};
+
+		clks: clock-controller@400fc000 {
+			compatible = "fsl,imxrt1050-ccm";
+			reg = <0x400fc000 0x4000>;
+			interrupts = <95>, <96>;
+			clocks = <&osc>;
+			clock-names = "osc";
+			#clock-cells = <1>;
+			assigned-clocks = <&clks IMXRT1050_CLK_PLL1_BYPASS>,
+				<&clks IMXRT1050_CLK_PLL1_BYPASS>,
+				<&clks IMXRT1050_CLK_PLL2_BYPASS>,
+				<&clks IMXRT1050_CLK_PLL3_BYPASS>,
+				<&clks IMXRT1050_CLK_PLL3_PFD1_664_62M>,
+				<&clks IMXRT1050_CLK_PLL2_PFD2_396M>;
+			assigned-clock-parents = <&clks IMXRT1050_CLK_PLL1_REF_SEL>,
+				<&clks IMXRT1050_CLK_PLL1_ARM>,
+				<&clks IMXRT1050_CLK_PLL2_SYS>,
+				<&clks IMXRT1050_CLK_PLL3_USB_OTG>,
+				<&clks IMXRT1050_CLK_PLL3_USB_OTG>,
+				<&clks IMXRT1050_CLK_PLL2_SYS>;
+		};
+
+		edma1: dma-controller@400e8000 {
+			#dma-cells = <2>;
+			compatible = "fsl,imx7ulp-edma";
+			reg = <0x400e8000 0x4000>,
+				<0x400ec000 0x4000>;
+			dma-channels = <32>;
+			interrupts = <0>, <1>, <2>, <3>, <4>, <5>, <6>, <7>, <8>,
+				<9>, <10>, <11>, <12>, <13>, <14>, <15>, <16>;
+			clock-names = "dma", "dmamux0";
+			clocks = <&clks IMXRT1050_CLK_DMA>,
+				 <&clks IMXRT1050_CLK_DMA_MUX>;
+		};
+
+		usdhc1: mmc@402c0000 {
+			compatible = "fsl,imxrt1050-usdhc", "fsl,imx6sl-usdhc";
+			reg = <0x402c0000 0x4000>;
+			interrupts = <110>;
+			clocks = <&clks IMXRT1050_CLK_IPG_PDOF>,
+				<&clks IMXRT1050_CLK_AHB_PODF>,
+				<&clks IMXRT1050_CLK_USDHC1>;
+			clock-names = "ipg", "ahb", "per";
+			bus-width = <4>;
+			fsl,wp-controller;
+			no-1-8-v;
+			max-frequency = <200000000>;
+			fsl,tuning-start-tap = <20>;
+			fsl,tuning-step = <2>;
+			status = "disabled";
+		};
+
+		gpio1: gpio@401b8000 {
+			compatible = "fsl,imxrt1050-gpio", "fsl,imx35-gpio";
+			reg = <0x401b8000 0x4000>;
+			interrupts = <80>, <81>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio2: gpio@401bc000 {
+			compatible = "fsl,imxrt1050-gpio", "fsl,imx35-gpio";
+			reg = <0x401bc000 0x4000>;
+			interrupts = <82>, <83>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio3: gpio@401c0000 {
+			compatible = "fsl,imxrt1050-gpio", "fsl,imx35-gpio";
+			reg = <0x401c0000 0x4000>;
+			interrupts = <84>, <85>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio4: gpio@401c4000 {
+			compatible = "fsl,imxrt1050-gpio", "fsl,imx35-gpio";
+			reg = <0x401c4000 0x4000>;
+			interrupts = <86>, <87>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio5: gpio@400c0000 {
+			compatible = "fsl,imxrt1050-gpio", "fsl,imx35-gpio";
+			reg = <0x400c0000 0x4000>;
+			interrupts = <88>, <89>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpt: timer@401ec000 {
+			compatible = "fsl,imxrt1050-gpt", "fsl,imx6dl-gpt", "fsl,imx6sl-gpt";
+			reg = <0x401ec000 0x4000>;
+			interrupts = <100>;
+			clocks = <&osc3M>;
+			clock-names = "per";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/imx/imxrt1170-pinfunc.h b/arch/arm/boot/dts/nxp/imx/imxrt1170-pinfunc.h
new file mode 100644
index 000000000000..3b9fff2f08e1
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imxrt1170-pinfunc.h
@@ -0,0 +1,1561 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
+/*
+ * Copyright (C) 2021
+ * Author(s): Jesse Taube <Mr.Bossman075@gmail.com>
+ */
+
+#ifndef _DT_BINDINGS_PINCTRL_IMXRT1170_PINFUNC_H
+#define _DT_BINDINGS_PINCTRL_IMXRT1170_PINFUNC_H
+
+#define IMX_PAD_SION		0x40000000
+
+/*
+ * The pin function ID is a tuple of
+ * <mux_reg conf_reg input_reg mux_mode input_val>
+ */
+
+#define IOMUXC_GPIO_LPSR_00_FLEXCAN3_TX				0x000 0x040 0x0 0x0 0x0
+#define IOMUXC_GPIO_LPSR_00_MIC_CLK				0x000 0x040 0x0 0x1 0x0
+#define IOMUXC_GPIO_LPSR_00_MQS_RIGHT				0x000 0x040 0x0 0x2 0x0
+#define IOMUXC_GPIO_LPSR_00_ARM_CM4_EVENTO			0x000 0x040 0x0 0x3 0x0
+#define IOMUXC_GPIO_LPSR_00_GPIO_MUX6_IO00			0x000 0x040 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_00_LPUART12_TXD			0x000 0x040 0x0B0 0x6 0x0
+#define IOMUXC_GPIO_LPSR_00_SAI4_MCLK				0x000 0x040 0x0C8 0x7 0x0
+#define IOMUXC_GPIO_LPSR_00_GPIO12_IO00				0x000 0x040 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_LPSR_01_FLEXCAN3_RX				0x004 0x044 0x080 0x0 0x0
+#define IOMUXC_GPIO_LPSR_01_MIC_BITSTREAM0			0x004 0x044 0x0B4 0x1 0x0
+#define IOMUXC_GPIO_LPSR_01_MQS_LEFT				0x004 0x044 0x0 0x2 0x0
+#define IOMUXC_GPIO_LPSR_01_ARM_CM4_EVENTI			0x004 0x044 0x0 0x3 0x0
+#define IOMUXC_GPIO_LPSR_01_GPIO_MUX6_IO01			0x004 0x044 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_01_LPUART12_RXD			0x004 0x044 0x0AC 0x6 0x0
+#define IOMUXC_GPIO_LPSR_01_GPIO12_IO01				0x004 0x044 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_LPSR_02_GPIO12_IO02				0x008 0x048 0x0 0xA 0x0
+#define IOMUXC_GPIO_LPSR_02_SRC_BOOT_MODE00			0x008 0x048 0x0 0x0 0x0
+#define IOMUXC_GPIO_LPSR_02_LPSPI5_SCK				0x008 0x048 0x098 0x1 0x0
+#define IOMUXC_GPIO_LPSR_02_SAI4_TX_DATA			0x008 0x048 0x0 0x2 0x0
+#define IOMUXC_GPIO_LPSR_02_MQS_RIGHT				0x008 0x048 0x0 0x3 0x0
+#define IOMUXC_GPIO_LPSR_02_GPIO_MUX6_IO02			0x008 0x048 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_LPSR_03_SRC_BOOT_MODE01			0x00C 0x04C 0x0 0x0 0x0
+#define IOMUXC_GPIO_LPSR_03_LPSPI5_PCS0				0x00C 0x04C 0x094 0x1 0x0
+#define IOMUXC_GPIO_LPSR_03_SAI4_TX_SYNC			0x00C 0x04C 0x0DC 0x2 0x0
+#define IOMUXC_GPIO_LPSR_03_MQS_LEFT				0x00C 0x04C 0x0 0x3 0x0
+#define IOMUXC_GPIO_LPSR_03_GPIO_MUX6_IO03			0x00C 0x04C 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_03_GPIO12_IO03				0x00C 0x04C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_LPSR_04_LPI2C5_SDA				0x010 0x050 0x088 0x0 0x0
+#define IOMUXC_GPIO_LPSR_04_LPSPI5_SOUT				0x010 0x050 0x0A0 0x1 0x0
+#define IOMUXC_GPIO_LPSR_04_SAI4_TX_BCLK			0x010 0x050 0x0D8 0x2 0x0
+#define IOMUXC_GPIO_LPSR_04_LPUART12_RTS_B			0x010 0x050 0x0 0x3 0x0
+#define IOMUXC_GPIO_LPSR_04_GPIO_MUX6_IO04			0x010 0x050 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_04_LPUART11_TXD			0x010 0x050 0x0A8 0x6 0x0
+#define IOMUXC_GPIO_LPSR_04_GPIO12_IO04				0x010 0x050 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_LPSR_05_GPIO12_IO05				0x014 0x054 0x0 0xA 0x0
+#define IOMUXC_GPIO_LPSR_05_LPI2C5_SCL				0x014 0x054 0x084 0x0 0x0
+#define IOMUXC_GPIO_LPSR_05_LPSPI5_SIN				0x014 0x054 0x09C 0x1 0x0
+#define IOMUXC_GPIO_LPSR_05_SAI4_MCLK				0x014 0x054 0x0C8 0x2 0x1
+#define IOMUXC_GPIO_LPSR_05_LPUART12_CTS_B			0x014 0x054 0x0 0x3 0x0
+#define IOMUXC_GPIO_LPSR_05_GPIO_MUX6_IO05			0x014 0x054 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_05_LPUART11_RXD			0x014 0x054 0x0A4 0x6 0x0
+#define IOMUXC_GPIO_LPSR_05_NMI_GLUE_NMI			0x014 0x054 0x0C4 0x7 0x0
+
+#define IOMUXC_GPIO_LPSR_06_LPI2C6_SDA				0x018 0x058 0x090 0x0 0x0
+#define IOMUXC_GPIO_LPSR_06_SAI4_RX_DATA			0x018 0x058 0x0D0 0x2 0x0
+#define IOMUXC_GPIO_LPSR_06_LPUART12_TXD			0x018 0x058 0x0B0 0x3 0x1
+#define IOMUXC_GPIO_LPSR_06_LPSPI6_PCS3				0x018 0x058 0x0 0x4 0x0
+#define IOMUXC_GPIO_LPSR_06_GPIO_MUX6_IO06			0x018 0x058 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_06_FLEXCAN3_TX				0x018 0x058 0x0 0x6 0x0
+#define IOMUXC_GPIO_LPSR_06_PIT2_TRIGGER3			0x018 0x058 0x0 0x7 0x0
+#define IOMUXC_GPIO_LPSR_06_LPSPI5_PCS1				0x018 0x058 0x0 0x8 0x0
+#define IOMUXC_GPIO_LPSR_06_GPIO12_IO06				0x018 0x058 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_LPSR_07_LPI2C6_SCL				0x01C 0x05C 0x08C 0x0 0x0
+#define IOMUXC_GPIO_LPSR_07_SAI4_RX_BCLK			0x01C 0x05C 0x0CC 0x2 0x0
+#define IOMUXC_GPIO_LPSR_07_LPUART12_RXD			0x01C 0x05C 0x0AC 0x3 0x1
+#define IOMUXC_GPIO_LPSR_07_LPSPI6_PCS2				0x01C 0x05C 0x0 0x4 0x0
+#define IOMUXC_GPIO_LPSR_07_GPIO_MUX6_IO07			0x01C 0x05C 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_07_FLEXCAN3_RX				0x01C 0x05C 0x080 0x6 0x1
+#define IOMUXC_GPIO_LPSR_07_PIT2_TRIGGER2			0x01C 0x05C 0x0 0x7 0x0
+#define IOMUXC_GPIO_LPSR_07_LPSPI5_PCS2				0x01C 0x05C 0x0 0x8 0x0
+#define IOMUXC_GPIO_LPSR_07_GPIO12_IO07				0x01C 0x05C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_LPSR_08_GPIO12_IO08				0x020 0x060 0x0 0xA 0x0
+#define IOMUXC_GPIO_LPSR_08_LPUART11_TXD			0x020 0x060 0x0A8 0x0 0x1
+#define IOMUXC_GPIO_LPSR_08_FLEXCAN3_TX				0x020 0x060 0x0 0x1 0x0
+#define IOMUXC_GPIO_LPSR_08_SAI4_RX_SYNC			0x020 0x060 0x0D4 0x2 0x0
+#define IOMUXC_GPIO_LPSR_08_MIC_CLK				0x020 0x060 0x0 0x3 0x0
+#define IOMUXC_GPIO_LPSR_08_LPSPI6_PCS1				0x020 0x060 0x0 0x4 0x0
+#define IOMUXC_GPIO_LPSR_08_GPIO_MUX6_IO08			0x020 0x060 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_08_LPI2C5_SDA				0x020 0x060 0x088 0x6 0x1
+#define IOMUXC_GPIO_LPSR_08_PIT2_TRIGGER1			0x020 0x060 0x0 0x7 0x0
+#define IOMUXC_GPIO_LPSR_08_LPSPI5_PCS3				0x020 0x060 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_LPSR_09_GPIO12_IO09				0x024 0x064 0x0 0xA 0x0
+#define IOMUXC_GPIO_LPSR_09_LPUART11_RXD			0x024 0x064 0x0A4 0x0 0x1
+#define IOMUXC_GPIO_LPSR_09_FLEXCAN3_RX				0x024 0x064 0x080 0x1 0x2
+#define IOMUXC_GPIO_LPSR_09_PIT2_TRIGGER0			0x024 0x064 0x0 0x2 0x0
+#define IOMUXC_GPIO_LPSR_09_MIC_BITSTREAM0			0x024 0x064 0x0B4 0x3 0x1
+#define IOMUXC_GPIO_LPSR_09_LPSPI6_PCS0				0x024 0x064 0x0 0x4 0x0
+#define IOMUXC_GPIO_LPSR_09_GPIO_MUX6_IO09			0x024 0x064 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_09_LPI2C5_SCL				0x024 0x064 0x084 0x6 0x1
+#define IOMUXC_GPIO_LPSR_09_SAI4_TX_DATA			0x024 0x064 0x0 0x7 0x0
+
+#define IOMUXC_GPIO_LPSR_10_GPIO12_IO10				0x028 0x068 0x0 0xA 0x0
+#define IOMUXC_GPIO_LPSR_10_JTAG_MUX_TRSTB			0x028 0x068 0x0 0x0 0x0
+#define IOMUXC_GPIO_LPSR_10_LPUART11_CTS_B			0x028 0x068 0x0 0x1 0x0
+#define IOMUXC_GPIO_LPSR_10_LPI2C6_SDA				0x028 0x068 0x090 0x2 0x1
+#define IOMUXC_GPIO_LPSR_10_MIC_BITSTREAM1			0x028 0x068 0x0B8 0x3 0x0
+#define IOMUXC_GPIO_LPSR_10_LPSPI6_SCK				0x028 0x068 0x0 0x4 0x0
+#define IOMUXC_GPIO_LPSR_10_GPIO_MUX6_IO10			0x028 0x068 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_10_LPI2C5_SCLS				0x028 0x068 0x0 0x6 0x0
+#define IOMUXC_GPIO_LPSR_10_SAI4_TX_SYNC			0x028 0x068 0x0DC 0x7 0x1
+#define IOMUXC_GPIO_LPSR_10_LPUART12_TXD			0x028 0x068 0x0B0 0x8 0x2
+
+#define IOMUXC_GPIO_LPSR_11_JTAG_MUX_TDO			0x02C 0x06C 0x0 0x0 0x0
+#define IOMUXC_GPIO_LPSR_11_LPUART11_RTS_B			0x02C 0x06C 0x0 0x1 0x0
+#define IOMUXC_GPIO_LPSR_11_LPI2C6_SCL				0x02C 0x06C 0x08C 0x2 0x1
+#define IOMUXC_GPIO_LPSR_11_MIC_BITSTREAM2			0x02C 0x06C 0x0BC 0x3 0x0
+#define IOMUXC_GPIO_LPSR_11_LPSPI6_SOUT				0x02C 0x06C 0x0 0x4 0x0
+#define IOMUXC_GPIO_LPSR_11_GPIO_MUX6_IO11			0x02C 0x06C 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_11_LPI2C5_SDAS				0x02C 0x06C 0x0 0x6 0x0
+#define IOMUXC_GPIO_LPSR_11_ARM_TRACE_SWO			0x02C 0x06C 0x0 0x7 0x0
+#define IOMUXC_GPIO_LPSR_11_LPUART12_RXD			0x02C 0x06C 0x0AC 0x8 0x2
+#define IOMUXC_GPIO_LPSR_11_GPIO12_IO11				0x02C 0x06C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_LPSR_12_GPIO12_IO12				0x030 0x070 0x0 0xA 0x0
+#define IOMUXC_GPIO_LPSR_12_JTAG_MUX_TDI			0x030 0x070 0x0 0x0 0x0
+#define IOMUXC_GPIO_LPSR_12_PIT2_TRIGGER0			0x030 0x070 0x0 0x1 0x0
+#define IOMUXC_GPIO_LPSR_12_MIC_BITSTREAM3			0x030 0x070 0x0C0 0x3 0x0
+#define IOMUXC_GPIO_LPSR_12_LPSPI6_SIN				0x030 0x070 0x0 0x4 0x0
+#define IOMUXC_GPIO_LPSR_12_GPIO_MUX6_IO12			0x030 0x070 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_12_LPI2C5_HREQ				0x030 0x070 0x0 0x6 0x0
+#define IOMUXC_GPIO_LPSR_12_SAI4_TX_BCLK			0x030 0x070 0x0D8 0x7 0x1
+#define IOMUXC_GPIO_LPSR_12_LPSPI5_SCK				0x030 0x070 0x098 0x8 0x1
+
+#define IOMUXC_GPIO_LPSR_13_GPIO12_IO13				0x034 0x074 0x0 0xA 0x0
+#define IOMUXC_GPIO_LPSR_13_JTAG_MUX_MOD			0x034 0x074 0x0 0x0 0x0
+#define IOMUXC_GPIO_LPSR_13_MIC_BITSTREAM1			0x034 0x074 0x0B8 0x1 0x1
+#define IOMUXC_GPIO_LPSR_13_PIT2_TRIGGER1			0x034 0x074 0x0 0x2 0x0
+#define IOMUXC_GPIO_LPSR_13_GPIO_MUX6_IO13			0x034 0x074 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_13_SAI4_RX_DATA			0x034 0x074 0x0D0 0x7 0x1
+#define IOMUXC_GPIO_LPSR_13_LPSPI5_PCS0				0x034 0x074 0x094 0x8 0x1
+
+#define IOMUXC_GPIO_LPSR_14_JTAG_MUX_TCK			0x038 0x078 0x0 0x0 0x0
+#define IOMUXC_GPIO_LPSR_14_MIC_BITSTREAM2			0x038 0x078 0x0BC 0x1 0x1
+#define IOMUXC_GPIO_LPSR_14_PIT2_TRIGGER2			0x038 0x078 0x0 0x2 0x0
+#define IOMUXC_GPIO_LPSR_14_GPIO_MUX6_IO14			0x038 0x078 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_14_SAI4_RX_BCLK			0x038 0x078 0x0CC 0x7 0x1
+#define IOMUXC_GPIO_LPSR_14_LPSPI5_SOUT				0x038 0x078 0x0A0 0x8 0x1
+#define IOMUXC_GPIO_LPSR_14_GPIO12_IO14				0x038 0x078 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_LPSR_15_GPIO12_IO15				0x03C 0x07C 0x0 0xA 0x0
+#define IOMUXC_GPIO_LPSR_15_JTAG_MUX_TMS			0x03C 0x07C 0x0 0x0 0x0
+#define IOMUXC_GPIO_LPSR_15_MIC_BITSTREAM3			0x03C 0x07C 0x0C0 0x1 0x1
+#define IOMUXC_GPIO_LPSR_15_PIT2_TRIGGER3			0x03C 0x07C 0x0 0x2 0x0
+#define IOMUXC_GPIO_LPSR_15_GPIO_MUX6_IO15			0x03C 0x07C 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_15_SAI4_RX_SYNC			0x03C 0x07C 0x0D4 0x7 0x1
+#define IOMUXC_GPIO_LPSR_15_LPSPI5_SIN				0x03C 0x07C 0x09C 0x8 0x1
+
+#define IOMUXC_WAKEUP_DIG_GPIO13_IO00				0x40C94000 0x40C94040 0x0 0x5 0x0
+#define IOMUXC_WAKEUP_DIG_NMI_GLUE_NMI				0x40C94000 0x40C94040 0x0C4 0x7 0x1
+
+#define IOMUXC_PMIC_ON_REQ_DIG_SNVS_LP_PMIC_ON_REQ		0x40C94004 0x40C94044 0x0 0x0 0x0
+#define IOMUXC_PMIC_ON_REQ_DIG_GPIO13_IO01			0x40C94004 0x40C94044 0x0 0x5 0x0
+
+#define IOMUXC_PMIC_STBY_REQ_DIG_CCM_PMIC_VSTBY_REQ		0x40C94008 0x40C94048 0x0 0x0 0x0
+#define IOMUXC_PMIC_STBY_REQ_DIG_GPIO13_IO02			0x40C94008 0x40C94048 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_00_DIG_SNVS_TAMPER0			0x40C9400C 0x40C9404C 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_00_DIG_GPIO13_IO03			0x40C9400C 0x40C9404C 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_01_DIG_SNVS_TAMPER1			0x40C94010 0x40C94050 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_01_DIG_GPIO13_IO04			0x40C94010 0x40C94050 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_02_DIG_SNVS_TAMPER2			0x40C94014 0x40C94054 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_02_DIG_GPIO13_IO05			0x40C94014 0x40C94054 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_03_DIG_SNVS_TAMPER3			0x40C94018 0x40C94058 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_03_DIG_GPIO13_IO06			0x40C94018 0x40C94058 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_04_DIG_SNVS_TAMPER4			0x40C9401C 0x40C9405C 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_04_DIG_GPIO13_IO07			0x40C9401C 0x40C9405C 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_05_DIG_SNVS_TAMPER5			0x40C94020 0x40C94060 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_05_DIG_GPIO13_IO08			0x40C94020 0x40C94060 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_06_DIG_SNVS_TAMPER6			0x40C94024 0x40C94064 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_06_DIG_GPIO13_IO09			0x40C94024 0x40C94064 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_07_DIG_SNVS_TAMPER7			0x40C94028 0x40C94068 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_07_DIG_GPIO13_IO10			0x40C94028 0x40C94068 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_08_DIG_SNVS_TAMPER8			0x40C9402C 0x40C9406C 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_08_DIG_GPIO13_IO11			0x40C9402C 0x40C9406C 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_09_DIG_SNVS_TAMPER9			0x40C94030 0x40C94070 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_09_DIG_GPIO13_IO12			0x40C94030 0x40C94070 0x0 0x5 0x0
+
+#define IOMUXC_TEST_MODE_DIG					0x0 0x40C94034 0x0 0x0 0x0
+
+#define IOMUXC_POR_B_DIG					0x0 0x40C94038 0x0 0x0 0x0
+
+#define IOMUXC_ONOFF_DIG					0x0 0x40C9403C 0x0 0x0 0x0
+
+#define IOMUXC_GPIO_EMC_B1_00_SEMC_DATA00			0x010 0x254 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_00_FLEXPWM4_PWM0_A			0x010 0x254 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_00_GPIO_MUX1_IO00			0x010 0x254 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_00_FLEXIO1_D00			0x010 0x254 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_00_GPIO7_IO00			0x010 0x254 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_01_GPIO7_IO01			0x014 0x258 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_01_SEMC_DATA01			0x014 0x258 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_01_FLEXPWM4_PWM0_B			0x014 0x258 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_01_GPIO_MUX1_IO01			0x014 0x258 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_01_FLEXIO1_D01			0x014 0x258 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_02_SEMC_DATA02			0x018 0x25C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_02_FLEXPWM4_PWM1_A			0x018 0x25C 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_02_GPIO_MUX1_IO02			0x018 0x25C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_02_FLEXIO1_D02			0x018 0x25C 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_02_GPIO7_IO02			0x018 0x25C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_03_SEMC_DATA03			0x01C 0x260 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_03_FLEXPWM4_PWM1_B			0x01C 0x260 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_03_GPIO_MUX1_IO03			0x01C 0x260 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_03_FLEXIO1_D03			0x01C 0x260 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_03_GPIO7_IO03			0x01C 0x260 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_04_GPIO7_IO04			0x020 0x264 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_04_SEMC_DATA04			0x020 0x264 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_04_FLEXPWM4_PWM2_A			0x020 0x264 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_04_GPIO_MUX1_IO04			0x020 0x264 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_04_FLEXIO1_D04			0x020 0x264 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_05_SEMC_DATA05			0x024 0x268 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_05_FLEXPWM4_PWM2_B			0x024 0x268 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_05_GPIO_MUX1_IO05			0x024 0x268 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_05_FLEXIO1_D05			0x024 0x268 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_05_GPIO7_IO05			0x024 0x268 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_06_SEMC_DATA06			0x028 0x26C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_06_FLEXPWM2_PWM0_A			0x028 0x26C 0x518 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_06_GPIO_MUX1_IO06			0x028 0x26C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_06_FLEXIO1_D06			0x028 0x26C 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_06_GPIO7_IO06			0x028 0x26C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_07_GPIO7_IO07			0x02C 0x270 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_07_SEMC_DATA07			0x02C 0x270 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_07_FLEXPWM2_PWM0_B			0x02C 0x270 0x524 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_07_GPIO_MUX1_IO07			0x02C 0x270 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_07_FLEXIO1_D07			0x02C 0x270 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_08_SEMC_DM00				0x030 0x274 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_08_FLEXPWM2_PWM1_A			0x030 0x274 0x51C 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_08_GPIO_MUX1_IO08			0x030 0x274 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_08_FLEXIO1_D08			0x030 0x274 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_08_GPIO7_IO08			0x030 0x274 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_09_SEMC_ADDR00			0x034 0x278 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_09_FLEXPWM2_PWM1_B			0x034 0x278 0x528 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_09_GPT5_CAPTURE1			0x034 0x278 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_09_GPIO_MUX1_IO09			0x034 0x278 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_09_FLEXIO1_D09			0x034 0x278 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_09_GPIO7_IO09			0x034 0x278 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_10_SEMC_ADDR01			0x038 0x27C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_10_FLEXPWM2_PWM2_A			0x038 0x27C 0x520 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_10_GPT5_CAPTURE2			0x038 0x27C 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_10_GPIO_MUX1_IO10			0x038 0x27C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_10_FLEXIO1_D10			0x038 0x27C 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_10_GPIO7_IO10			0x038 0x27C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_11_GPIO7_IO11			0x03C 0x280 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_11_SEMC_ADDR02			0x03C 0x280 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_11_FLEXPWM2_PWM2_B			0x03C 0x280 0x52C 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_11_GPT5_COMPARE1			0x03C 0x280 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_11_GPIO_MUX1_IO11			0x03C 0x280 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_11_FLEXIO1_D11			0x03C 0x280 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_12_SEMC_ADDR03			0x040 0x284 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_12_XBAR1_INOUT04			0x040 0x284 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_12_GPT5_COMPARE2			0x040 0x284 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_12_GPIO_MUX1_IO12			0x040 0x284 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_12_FLEXIO1_D12			0x040 0x284 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_12_GPIO7_IO12			0x040 0x284 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_13_SEMC_ADDR04			0x044 0x288 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_13_XBAR1_INOUT05			0x044 0x288 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_13_GPT5_COMPARE3			0x044 0x288 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_13_GPIO_MUX1_IO13			0x044 0x288 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_13_FLEXIO1_D13			0x044 0x288 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_13_GPIO7_IO13			0x044 0x288 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_14_GPIO7_IO14			0x048 0x28C 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_14_SEMC_ADDR05			0x048 0x28C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_14_XBAR1_INOUT06			0x048 0x28C 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_14_GPT5_CLK				0x048 0x28C 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_14_GPIO_MUX1_IO14			0x048 0x28C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_14_FLEXIO1_D14			0x048 0x28C 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_15_SEMC_ADDR06			0x04C 0x290 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_15_XBAR1_INOUT07			0x04C 0x290 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_15_GPIO_MUX1_IO15			0x04C 0x290 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_15_FLEXIO1_D15			0x04C 0x290 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_15_GPIO7_IO15			0x04C 0x290 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_16_SEMC_ADDR07			0x050 0x294 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_16_XBAR1_INOUT08			0x050 0x294 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_16_GPIO_MUX1_IO16			0x050 0x294 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_16_FLEXIO1_D16			0x050 0x294 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_16_GPIO7_IO16			0x050 0x294 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_17_GPIO7_IO17			0x054 0x298 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_17_SEMC_ADDR08			0x054 0x298 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_17_FLEXPWM4_PWM3_A			0x054 0x298 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_17_TMR1_TIMER0			0x054 0x298 0x63C 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_17_GPIO_MUX1_IO17			0x054 0x298 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_17_FLEXIO1_D17			0x054 0x298 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_18_SEMC_ADDR09			0x058 0x29C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_18_FLEXPWM4_PWM3_B			0x058 0x29C 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_18_TMR2_TIMER0			0x058 0x29C 0x648 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_18_GPIO_MUX1_IO18			0x058 0x29C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_18_FLEXIO1_D18			0x058 0x29C 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_18_GPIO7_IO18			0x058 0x29C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_19_SEMC_ADDR11			0x05C 0x2A0 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_19_FLEXPWM2_PWM3_A			0x05C 0x2A0 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_19_TMR3_TIMER0			0x05C 0x2A0 0x654 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_19_GPIO_MUX1_IO19			0x05C 0x2A0 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_19_FLEXIO1_D19			0x05C 0x2A0 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_19_GPIO7_IO19			0x05C 0x2A0 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_20_SEMC_ADDR12			0x060 0x2A4 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_20_FLEXPWM2_PWM3_B			0x060 0x2A4 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_20_TMR4_TIMER0			0x060 0x2A4 0x660 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_20_GPIO_MUX1_IO20			0x060 0x2A4 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_20_FLEXIO1_D20			0x060 0x2A4 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_20_GPIO7_IO20			0x060 0x2A4 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_21_GPIO7_IO21			0x064 0x2A8 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_21_SEMC_BA0				0x064 0x2A8 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_21_FLEXPWM3_PWM3_A			0x064 0x2A8 0x53C 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_21_GPIO_MUX1_IO21			0x064 0x2A8 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_21_FLEXIO1_D21			0x064 0x2A8 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_22_GPIO7_IO22			0x068 0x2AC 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_22_SEMC_BA1				0x068 0x2AC 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_22_FLEXPWM3_PWM3_B			0x068 0x2AC 0x54C 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_22_GPIO_MUX1_IO22			0x068 0x2AC 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_22_FLEXIO1_D22			0x068 0x2AC 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_23_SEMC_ADDR10			0x06C 0x2B0 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_23_FLEXPWM1_PWM0_A			0x06C 0x2B0 0x500 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_23_GPIO_MUX1_IO23			0x06C 0x2B0 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_23_FLEXIO1_D23			0x06C 0x2B0 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_23_GPIO7_IO23			0x06C 0x2B0 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_24_GPIO7_IO24			0x070 0x2B4 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_24_SEMC_CAS				0x070 0x2B4 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_24_FLEXPWM1_PWM0_B			0x070 0x2B4 0x50C 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_24_GPIO_MUX1_IO24			0x070 0x2B4 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_24_FLEXIO1_D24			0x070 0x2B4 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_25_GPIO7_IO25			0x074 0x2B8 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_25_SEMC_RAS				0x074 0x2B8 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_25_FLEXPWM1_PWM1_A			0x074 0x2B8 0x504 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_25_GPIO_MUX1_IO25			0x074 0x2B8 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_25_FLEXIO1_D25			0x074 0x2B8 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_26_SEMC_CLK				0x078 0x2BC 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_26_FLEXPWM1_PWM1_B			0x078 0x2BC 0x510 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_26_GPIO_MUX1_IO26			0x078 0x2BC 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_26_FLEXIO1_D26			0x078 0x2BC 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_26_GPIO7_IO26			0x078 0x2BC 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_27_GPIO7_IO27			0x07C 0x2C0 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_27_SEMC_CKE				0x07C 0x2C0 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_27_FLEXPWM1_PWM2_A			0x07C 0x2C0 0x508 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_27_GPIO_MUX1_IO27			0x07C 0x2C0 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_27_FLEXIO1_D27			0x07C 0x2C0 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_28_GPIO7_IO28			0x080 0x2C4 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_28_SEMC_WE				0x080 0x2C4 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_28_FLEXPWM1_PWM2_B			0x080 0x2C4 0x514 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_28_GPIO_MUX1_IO28			0x080 0x2C4 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_28_FLEXIO1_D28			0x080 0x2C4 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_29_SEMC_CS0				0x084 0x2C8 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_29_FLEXPWM3_PWM0_A			0x084 0x2C8 0x530 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_29_GPIO_MUX1_IO29			0x084 0x2C8 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_29_FLEXIO1_D29			0x084 0x2C8 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_29_GPIO7_IO29			0x084 0x2C8 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_30_SEMC_DATA08			0x088 0x2CC 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_30_FLEXPWM3_PWM0_B			0x088 0x2CC 0x540 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_30_GPIO_MUX1_IO30			0x088 0x2CC 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_30_FLEXIO1_D30			0x088 0x2CC 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_30_GPIO7_IO30			0x088 0x2CC 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_31_GPIO7_IO31			0x08C 0x2D0 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_31_SEMC_DATA09			0x08C 0x2D0 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_31_FLEXPWM3_PWM1_A			0x08C 0x2D0 0x534 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_31_GPIO_MUX1_IO31			0x08C 0x2D0 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_31_FLEXIO1_D31			0x08C 0x2D0 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_32_GPIO8_IO00			0x090 0x2D4 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_32_SEMC_DATA10			0x090 0x2D4 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_32_FLEXPWM3_PWM1_B			0x090 0x2D4 0x544 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_32_GPIO_MUX2_IO00			0x090 0x2D4 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_EMC_B1_33_SEMC_DATA11			0x094 0x2D8 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_33_FLEXPWM3_PWM2_A			0x094 0x2D8 0x538 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_33_GPIO_MUX2_IO01			0x094 0x2D8 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_33_GPIO8_IO01			0x094 0x2D8 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_34_GPIO8_IO02			0x098 0x2DC 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_34_SEMC_DATA12			0x098 0x2DC 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_34_FLEXPWM3_PWM2_B			0x098 0x2DC 0x548 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_34_GPIO_MUX2_IO02			0x098 0x2DC 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_EMC_B1_35_GPIO8_IO03			0x09C 0x2E0 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_35_SEMC_DATA13			0x09C 0x2E0 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_35_XBAR1_INOUT09			0x09C 0x2E0 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_35_GPIO_MUX2_IO03			0x09C 0x2E0 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_EMC_B1_36_SEMC_DATA14			0x0A0 0x2E4 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_36_XBAR1_INOUT10			0x0A0 0x2E4 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_36_GPIO_MUX2_IO04			0x0A0 0x2E4 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_36_GPIO8_IO04			0x0A0 0x2E4 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_37_GPIO8_IO05			0x0A4 0x2E8 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_37_SEMC_DATA15			0x0A4 0x2E8 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_37_XBAR1_INOUT11			0x0A4 0x2E8 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_37_GPIO_MUX2_IO05			0x0A4 0x2E8 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_EMC_B1_38_GPIO8_IO06			0x0A8 0x2EC 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_38_SEMC_DM01				0x0A8 0x2EC 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_38_FLEXPWM1_PWM3_A			0x0A8 0x2EC 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_38_TMR1_TIMER1			0x0A8 0x2EC 0x640 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_38_GPIO_MUX2_IO06			0x0A8 0x2EC 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_EMC_B1_39_SEMC_DQS				0x0AC 0x2F0 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_39_FLEXPWM1_PWM3_B			0x0AC 0x2F0 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_39_TMR2_TIMER1			0x0AC 0x2F0 0x64C 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_39_GPIO_MUX2_IO07			0x0AC 0x2F0 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_39_GPIO8_IO07			0x0AC 0x2F0 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_40_SEMC_RDY				0x0B0 0x2F4 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_40_XBAR1_INOUT12			0x0B0 0x2F4 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_40_MQS_RIGHT				0x0B0 0x2F4 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_40_LPUART6_TXD			0x0B0 0x2F4 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B1_40_GPIO_MUX2_IO08			0x0B0 0x2F4 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_40_ENET_1G_MDC			0x0B0 0x2F4 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B1_40_CCM_CLKO1				0x0B0 0x2F4 0x0 0x9 0x0
+#define IOMUXC_GPIO_EMC_B1_40_GPIO8_IO08			0x0B0 0x2F4 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_41_GPIO8_IO09			0x0B4 0x2F8 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_41_SEMC_CSX00			0x0B4 0x2F8 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_41_XBAR1_INOUT13			0x0B4 0x2F8 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_41_MQS_LEFT				0x0B4 0x2F8 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_41_LPUART6_RXD			0x0B4 0x2F8 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B1_41_FLEXSPI2_B_DATA07			0x0B4 0x2F8 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B1_41_GPIO_MUX2_IO09			0x0B4 0x2F8 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_41_ENET_1G_MDIO			0x0B4 0x2F8 0x4C8 0x7 0x0
+#define IOMUXC_GPIO_EMC_B1_41_CCM_CLKO2				0x0B4 0x2F8 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_EMC_B2_00_SEMC_DATA16			0x0B8 0x2FC 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_00_CCM_ENET_REF_CLK_25M		0x0B8 0x2FC 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_00_TMR3_TIMER1			0x0B8 0x2FC 0x658 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_00_LPUART6_CTS_B			0x0B8 0x2FC 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_00_FLEXSPI2_B_DATA06			0x0B8 0x2FC 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_00_GPIO_MUX2_IO10			0x0B8 0x2FC 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_00_XBAR1_INOUT20			0x0B8 0x2FC 0x6D8 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_00_ENET_QOS_1588_EVENT1_OUT		0x0B8 0x2FC 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_00_LPSPI1_SCK			0x0B8 0x2FC 0x5D0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_00_LPI2C2_SCL			0x0B8 0x2FC 0x5B4 0x9 0x0
+#define IOMUXC_GPIO_EMC_B2_00_GPIO8_IO10			0x0B8 0x2FC 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_00_FLEXPWM3_PWM0_A			0x0B8 0x2FC 0x530 0xB 0x1
+
+#define IOMUXC_GPIO_EMC_B2_01_SEMC_DATA17			0x0BC 0x300 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_01_USDHC2_CD_B			0x0BC 0x300 0x6D0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_01_TMR4_TIMER1			0x0BC 0x300 0x664 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_01_LPUART6_RTS_B			0x0BC 0x300 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_01_FLEXSPI2_B_DATA05			0x0BC 0x300 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_01_GPIO_MUX2_IO11			0x0BC 0x300 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_01_XBAR1_INOUT21			0x0BC 0x300 0x6DC 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_01_ENET_QOS_1588_EVENT1_IN		0x0BC 0x300 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_01_LPSPI1_PCS0			0x0BC 0x300 0x5CC 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_01_LPI2C2_SDA			0x0BC 0x300 0x5B8 0x9 0x0
+#define IOMUXC_GPIO_EMC_B2_01_GPIO8_IO11			0x0BC 0x300 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_01_FLEXPWM3_PWM0_B			0x0BC 0x300 0x540 0xB 0x1
+
+#define IOMUXC_GPIO_EMC_B2_02_SEMC_DATA18			0x0C0 0x304 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_02_USDHC2_WP				0x0C0 0x304 0x6D4 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_02_VIDEO_MUX_CSI_DATA23		0x0C0 0x304 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_02_FLEXSPI2_B_DATA04			0x0C0 0x304 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_02_GPIO_MUX2_IO12			0x0C0 0x304 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_02_XBAR1_INOUT22			0x0C0 0x304 0x6E0 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_02_ENET_QOS_1588_EVENT1_AUX_IN	0x0C0 0x304 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_02_LPSPI1_SOUT			0x0C0 0x304 0x5D8 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_02_GPIO8_IO12			0x0C0 0x304 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_02_FLEXPWM3_PWM1_A			0x0C0 0x304 0x534 0xB 0x1
+
+#define IOMUXC_GPIO_EMC_B2_03_SEMC_DATA19			0x0C4 0x308 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_03_USDHC2_VSELECT			0x0C4 0x308 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_03_VIDEO_MUX_CSI_DATA22		0x0C4 0x308 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_03_FLEXSPI2_B_DATA03			0x0C4 0x308 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_03_GPIO_MUX2_IO13			0x0C4 0x308 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_03_XBAR1_INOUT23			0x0C4 0x308 0x6E4 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_03_ENET_1G_TX_DATA03			0x0C4 0x308 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_03_LPSPI1_SIN			0x0C4 0x308 0x5D4 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_03_GPIO8_IO13			0x0C4 0x308 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_03_FLEXPWM3_PWM1_B			0x0C4 0x308 0x544 0xB 0x1
+
+#define IOMUXC_GPIO_EMC_B2_04_SEMC_DATA20			0x0C8 0x30C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_04_USDHC2_RESET_B			0x0C8 0x30C 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_04_SAI2_MCLK				0x0C8 0x30C 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_04_VIDEO_MUX_CSI_DATA21		0x0C8 0x30C 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_04_FLEXSPI2_B_DATA02			0x0C8 0x30C 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_04_GPIO_MUX2_IO14			0x0C8 0x30C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_04_XBAR1_INOUT24			0x0C8 0x30C 0x6E8 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_04_ENET_1G_TX_DATA02			0x0C8 0x30C 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_04_LPSPI3_SCK			0x0C8 0x30C 0x600 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_04_GPIO8_IO14			0x0C8 0x30C 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_04_FLEXPWM3_PWM2_A			0x0C8 0x30C 0x538 0xB 0x1
+
+#define IOMUXC_GPIO_EMC_B2_05_SEMC_DATA21			0x0CC 0x310 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_05_GPT3_CLK				0x0CC 0x310 0x598 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_05_SAI2_RX_SYNC			0x0CC 0x310 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_05_VIDEO_MUX_CSI_DATA20		0x0CC 0x310 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_05_FLEXSPI2_B_DATA01			0x0CC 0x310 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_05_GPIO_MUX2_IO15			0x0CC 0x310 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_05_XBAR1_INOUT25			0x0CC 0x310 0x6EC 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_05_ENET_1G_RX_CLK			0x0CC 0x310 0x4CC 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_05_LPSPI3_PCS0			0x0CC 0x310 0x5F0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_05_PIT1_TRIGGER0			0x0CC 0x310 0x0 0x9 0x0
+#define IOMUXC_GPIO_EMC_B2_05_GPIO8_IO15			0x0CC 0x310 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_05_FLEXPWM3_PWM2_B			0x0CC 0x310 0x548 0xB 0x1
+
+#define IOMUXC_GPIO_EMC_B2_06_SEMC_DATA22			0x0D0 0x314 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_06_GPT3_CAPTURE1			0x0D0 0x314 0x590 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_06_GPIO8_IO16			0x0D0 0x314 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_06_SAI2_RX_BCLK			0x0D0 0x314 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_06_FLEXPWM3_PWM3_A			0x0D0 0x314 0x53C 0xB 0x1
+#define IOMUXC_GPIO_EMC_B2_06_VIDEO_MUX_CSI_DATA19		0x0D0 0x314 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_06_FLEXSPI2_B_DATA00			0x0D0 0x314 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_06_GPIO_MUX2_IO16			0x0D0 0x314 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_06_XBAR1_INOUT26			0x0D0 0x314 0x6F0 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_06_ENET_1G_TX_ER			0x0D0 0x314 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_06_LPSPI3_SOUT			0x0D0 0x314 0x608 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_06_PIT1_TRIGGER1			0x0D0 0x314 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_EMC_B2_07_SEMC_DATA23			0x0D4 0x318 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_07_GPT3_CAPTURE2			0x0D4 0x318 0x594 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_07_SAI2_RX_DATA			0x0D4 0x318 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_07_VIDEO_MUX_CSI_DATA18		0x0D4 0x318 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_07_FLEXSPI2_B_DQS			0x0D4 0x318 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_07_GPIO_MUX2_IO17			0x0D4 0x318 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_07_XBAR1_INOUT27			0x0D4 0x318 0x6F4 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_07_ENET_1G_RX_DATA03			0x0D4 0x318 0x4DC 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_07_LPSPI3_SIN			0x0D4 0x318 0x604 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_07_PIT1_TRIGGER2			0x0D4 0x318 0x0 0x9 0x0
+#define IOMUXC_GPIO_EMC_B2_07_GPIO8_IO17			0x0D4 0x318 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_07_FLEXPWM3_PWM3_B			0x0D4 0x318 0x54C 0xB 0x1
+
+#define IOMUXC_GPIO_EMC_B2_08_SEMC_DM02				0x0D8 0x31C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_08_GPT3_COMPARE1			0x0D8 0x31C 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_08_SAI2_TX_DATA			0x0D8 0x31C 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_08_VIDEO_MUX_CSI_DATA17		0x0D8 0x31C 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_08_FLEXSPI2_B_SS0_B			0x0D8 0x31C 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_08_GPIO_MUX2_IO18			0x0D8 0x31C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_08_XBAR1_INOUT28			0x0D8 0x31C 0x6F8 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_08_ENET_1G_RX_DATA02			0x0D8 0x31C 0x4D8 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_08_LPSPI3_PCS1			0x0D8 0x31C 0x5F4 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_08_PIT1_TRIGGER3			0x0D8 0x31C 0x0 0x9 0x0
+#define IOMUXC_GPIO_EMC_B2_08_GPIO8_IO18			0x0D8 0x31C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B2_09_GPIO8_IO19			0x0DC 0x320 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_09_SEMC_DATA24			0x0DC 0x320 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_09_GPT3_COMPARE2			0x0DC 0x320 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_09_SAI2_TX_BCLK			0x0DC 0x320 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_09_VIDEO_MUX_CSI_DATA16		0x0DC 0x320 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_09_FLEXSPI2_B_SCLK			0x0DC 0x320 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_09_GPIO_MUX2_IO19			0x0DC 0x320 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_09_XBAR1_INOUT29			0x0DC 0x320 0x6FC 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_09_ENET_1G_CRS			0x0DC 0x320 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_09_LPSPI3_PCS2			0x0DC 0x320 0x5F8 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_09_TMR1_TIMER0			0x0DC 0x320 0x63C 0x9 0x1
+
+#define IOMUXC_GPIO_EMC_B2_10_GPIO8_IO20			0x0E0 0x324 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_10_SEMC_DATA25			0x0E0 0x324 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_10_GPT3_COMPARE3			0x0E0 0x324 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_10_SAI2_TX_SYNC			0x0E0 0x324 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_10_VIDEO_MUX_CSI_FIELD		0x0E0 0x324 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_10_FLEXSPI2_A_SCLK			0x0E0 0x324 0x58C 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_10_GPIO_MUX2_IO20			0x0E0 0x324 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_10_XBAR1_INOUT30			0x0E0 0x324 0x700 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_10_ENET_1G_COL			0x0E0 0x324 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_10_LPSPI3_PCS3			0x0E0 0x324 0x5FC 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_10_TMR1_TIMER1			0x0E0 0x324 0x640 0x9 0x1
+
+#define IOMUXC_GPIO_EMC_B2_11_SEMC_DATA26			0x0E4 0x328 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_11_SPDIF_IN				0x0E4 0x328 0x6B4 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_11_ENET_1G_TX_DATA00			0x0E4 0x328 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_11_SAI3_RX_SYNC			0x0E4 0x328 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_11_FLEXSPI2_A_SS0_B			0x0E4 0x328 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_11_GPIO_MUX2_IO21			0x0E4 0x328 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_11_XBAR1_INOUT31			0x0E4 0x328 0x704 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_11_EMVSIM1_IO			0x0E4 0x328 0x69C 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_11_TMR1_TIMER2			0x0E4 0x328 0x644 0x9 0x0
+#define IOMUXC_GPIO_EMC_B2_11_GPIO8_IO21			0x0E4 0x328 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B2_12_SEMC_DATA27			0x0E8 0x32C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_12_SPDIF_OUT				0x0E8 0x32C 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_12_ENET_1G_TX_DATA01			0x0E8 0x32C 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_12_SAI3_RX_BCLK			0x0E8 0x32C 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_12_FLEXSPI2_A_DQS			0x0E8 0x32C 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_12_GPIO_MUX2_IO22			0x0E8 0x32C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_12_XBAR1_INOUT32			0x0E8 0x32C 0x708 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_12_EMVSIM1_CLK			0x0E8 0x32C 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_12_TMR1_TIMER3			0x0E8 0x32C 0x0 0x9 0x0
+#define IOMUXC_GPIO_EMC_B2_12_GPIO8_IO22			0x0E8 0x32C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B2_13_GPIO8_IO23			0x0EC 0x330 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_13_SEMC_DATA28			0x0EC 0x330 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_13_ENET_1G_TX_EN			0x0EC 0x330 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_13_SAI3_RX_DATA			0x0EC 0x330 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_13_FLEXSPI2_A_DATA00			0x0EC 0x330 0x57C 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_13_GPIO_MUX2_IO23			0x0EC 0x330 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_13_XBAR1_INOUT33			0x0EC 0x330 0x70C 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_13_EMVSIM1_RST			0x0EC 0x330 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_13_TMR2_TIMER0			0x0EC 0x330 0x648 0x9 0x1
+
+#define IOMUXC_GPIO_EMC_B2_14_SEMC_DATA29			0x0F0 0x334 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_14_ENET_1G_TX_CLK_IO			0x0F0 0x334 0x4E8 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_14_SAI3_TX_DATA			0x0F0 0x334 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_14_FLEXSPI2_A_DATA01			0x0F0 0x334 0x580 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_14_GPIO_MUX2_IO24			0x0F0 0x334 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_14_XBAR1_INOUT34			0x0F0 0x334 0x710 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_14_SFA_ipp_do_atx_clk_under_test	0x0F0 0x334 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_14_EMVSIM1_SVEN			0x0F0 0x334 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_14_TMR2_TIMER1			0x0F0 0x334 0x64C 0x9 0x1
+#define IOMUXC_GPIO_EMC_B2_14_GPIO8_IO24			0x0F0 0x334 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B2_15_SEMC_DATA30			0x0F4 0x338 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_15_ENET_1G_RX_DATA00			0x0F4 0x338 0x4D0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_15_SAI3_TX_BCLK			0x0F4 0x338 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_15_FLEXSPI2_A_DATA02			0x0F4 0x338 0x584 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_15_GPIO_MUX2_IO25			0x0F4 0x338 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_15_XBAR1_INOUT35			0x0F4 0x338 0x714 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_15_EMVSIM1_PD			0x0F4 0x338 0x6A0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_15_TMR2_TIMER2			0x0F4 0x338 0x650 0x9 0x0
+#define IOMUXC_GPIO_EMC_B2_15_GPIO8_IO25			0x0F4 0x338 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B2_16_GPIO8_IO26			0x0F8 0x33C 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_16_SEMC_DATA31			0x0F8 0x33C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_16_XBAR1_INOUT14			0x0F8 0x33C 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_16_ENET_1G_RX_DATA01			0x0F8 0x33C 0x4D4 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_16_SAI3_TX_SYNC			0x0F8 0x33C 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_16_FLEXSPI2_A_DATA03			0x0F8 0x33C 0x588 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_16_GPIO_MUX2_IO26			0x0F8 0x33C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_16_EMVSIM1_POWER_FAIL		0x0F8 0x33C 0x6A4 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_16_TMR2_TIMER3			0x0F8 0x33C 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_EMC_B2_17_SEMC_DM03				0x0FC 0x340 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_17_XBAR1_INOUT15			0x0FC 0x340 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_17_ENET_1G_RX_EN			0x0FC 0x340 0x4E0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_17_SAI3_MCLK				0x0FC 0x340 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_17_FLEXSPI2_A_DATA04			0x0FC 0x340 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_17_GPIO_MUX2_IO27			0x0FC 0x340 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_17_WDOG1_ANY				0x0FC 0x340 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_17_TMR3_TIMER0			0x0FC 0x340 0x654 0x9 0x1
+#define IOMUXC_GPIO_EMC_B2_17_GPIO8_IO27			0x0FC 0x340 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B2_18_SEMC_DQS4				0x100 0x344 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_18_XBAR1_INOUT16			0x100 0x344 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_18_ENET_1G_RX_ER			0x100 0x344 0x4E4 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_18_EWM_OUT_B				0x100 0x344 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_18_FLEXSPI2_A_DATA05			0x100 0x344 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_18_GPIO_MUX2_IO28			0x100 0x344 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_18_FLEXSPI1_A_DQS			0x100 0x344 0x550 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_18_WDOG1_B				0x100 0x344 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_18_TMR3_TIMER1			0x100 0x344 0x658 0x9 0x1
+#define IOMUXC_GPIO_EMC_B2_18_GPIO8_IO28			0x100 0x344 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B2_19_GPIO8_IO29			0x104 0x348 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_19_SEMC_CLKX00			0x104 0x348 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_19_ENET_MDC				0x104 0x348 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_19_ENET_1G_MDC			0x104 0x348 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_19_ENET_1G_REF_CLK			0x104 0x348 0x4C4 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_19_FLEXSPI2_A_DATA06			0x104 0x348 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_19_GPIO_MUX2_IO29			0x104 0x348 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_19_ENET_QOS_MDC			0x104 0x348 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_19_TMR3_TIMER2			0x104 0x348 0x65C 0x9 0x0
+
+#define IOMUXC_GPIO_EMC_B2_20_GPIO8_IO30			0x108 0x34C 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_20_SEMC_CLKX01			0x108 0x34C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_20_ENET_MDIO				0x108 0x34C 0x4AC 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_20_ENET_1G_MDIO			0x108 0x34C 0x4C8 0x2 0x1
+#define IOMUXC_GPIO_EMC_B2_20_ENET_QOS_REF_CLK			0x108 0x34C 0x4A0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_20_FLEXSPI2_A_DATA07			0x108 0x34C 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_20_GPIO_MUX2_IO30			0x108 0x34C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_20_ENET_QOS_MDIO			0x108 0x34C 0x4EC 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_20_TMR3_TIMER3			0x108 0x34C 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_AD_00_GPIO8_IO31				0x10C 0x350 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_00_EMVSIM1_IO				0x10C 0x350 0x69C 0x0 0x1
+#define IOMUXC_GPIO_AD_00_FLEXCAN2_TX				0x10C 0x350 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_00_ENET_1G_1588_EVENT1_IN		0x10C 0x350 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_00_GPT2_CAPTURE1				0x10C 0x350 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_00_FLEXPWM1_PWM0_A			0x10C 0x350 0x500 0x4 0x1
+#define IOMUXC_GPIO_AD_00_GPIO_MUX2_IO31			0x10C 0x350 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_00_LPUART7_TXD				0x10C 0x350 0x630 0x6 0x0
+#define IOMUXC_GPIO_AD_00_FLEXIO2_D00				0x10C 0x350 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_00_FLEXSPI2_B_SS1_B			0x10C 0x350 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_AD_01_GPIO9_IO00				0x110 0x354 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_01_EMVSIM1_CLK				0x110 0x354 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_01_FLEXCAN2_RX				0x110 0x354 0x49C 0x1 0x0
+#define IOMUXC_GPIO_AD_01_ENET_1G_1588_EVENT1_OUT		0x110 0x354 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_01_GPT2_CAPTURE2				0x110 0x354 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_01_FLEXPWM1_PWM0_B			0x110 0x354 0x50C 0x4 0x1
+#define IOMUXC_GPIO_AD_01_GPIO_MUX3_IO00			0x110 0x354 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_01_LPUART7_RXD				0x110 0x354 0x62C 0x6 0x0
+#define IOMUXC_GPIO_AD_01_FLEXIO2_D01				0x110 0x354 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_01_FLEXSPI2_A_SS1_B			0x110 0x354 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_AD_02_GPIO9_IO01				0x114 0x358 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_02_EMVSIM1_RST				0x114 0x358 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_02_LPUART7_CTS_B				0x114 0x358 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_02_ENET_1G_1588_EVENT2_IN		0x114 0x358 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_02_GPT2_COMPARE1				0x114 0x358 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_02_FLEXPWM1_PWM1_A			0x114 0x358 0x504 0x4 0x1
+#define IOMUXC_GPIO_AD_02_GPIO_MUX3_IO01			0x114 0x358 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_02_LPUART8_TXD				0x114 0x358 0x638 0x6 0x0
+#define IOMUXC_GPIO_AD_02_FLEXIO2_D02				0x114 0x358 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_02_VIDEO_MUX_EXT_DCIC1			0x114 0x358 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_AD_03_GPIO9_IO02				0x118 0x35C 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_03_EMVSIM1_SVEN				0x118 0x35C 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_03_LPUART7_RTS_B				0x118 0x35C 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_03_ENET_1G_1588_EVENT2_OUT		0x118 0x35C 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_03_GPT2_COMPARE2				0x118 0x35C 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_03_FLEXPWM1_PWM1_B			0x118 0x35C 0x510 0x4 0x1
+#define IOMUXC_GPIO_AD_03_GPIO_MUX3_IO02			0x118 0x35C 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_03_LPUART8_RXD				0x118 0x35C 0x634 0x6 0x0
+#define IOMUXC_GPIO_AD_03_FLEXIO2_D03				0x118 0x35C 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_03_VIDEO_MUX_EXT_DCIC2			0x118 0x35C 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_AD_04_EMVSIM1_PD				0x11C 0x360 0x6A0 0x0 0x1
+#define IOMUXC_GPIO_AD_04_LPUART8_CTS_B				0x11C 0x360 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_04_ENET_1G_1588_EVENT3_IN		0x11C 0x360 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_04_GPT2_COMPARE3				0x11C 0x360 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_04_FLEXPWM1_PWM2_A			0x11C 0x360 0x508 0x4 0x1
+#define IOMUXC_GPIO_AD_04_GPIO_MUX3_IO03			0x11C 0x360 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_04_WDOG1_B				0x11C 0x360 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_04_FLEXIO2_D04				0x11C 0x360 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_04_TMR4_TIMER0				0x11C 0x360 0x660 0x9 0x1
+#define IOMUXC_GPIO_AD_04_GPIO9_IO03				0x11C 0x360 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_AD_05_EMVSIM1_POWER_FAIL			0x120 0x364 0x6A4 0x0 0x1
+#define IOMUXC_GPIO_AD_05_LPUART8_RTS_B				0x120 0x364 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_05_ENET_1G_1588_EVENT3_OUT		0x120 0x364 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_05_GPT2_CLK				0x120 0x364 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_05_FLEXPWM1_PWM2_B			0x120 0x364 0x514 0x4 0x1
+#define IOMUXC_GPIO_AD_05_GPIO_MUX3_IO04			0x120 0x364 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_05_WDOG2_B				0x120 0x364 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_05_FLEXIO2_D05				0x120 0x364 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_05_TMR4_TIMER1				0x120 0x364 0x664 0x9 0x1
+#define IOMUXC_GPIO_AD_05_GPIO9_IO04				0x120 0x364 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_AD_06_USB_OTG2_OC				0x124 0x368 0x6B8 0x0 0x0
+#define IOMUXC_GPIO_AD_06_FLEXCAN1_TX				0x124 0x368 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_06_EMVSIM2_IO				0x124 0x368 0x6A8 0x2 0x0
+#define IOMUXC_GPIO_AD_06_GPT3_CAPTURE1				0x124 0x368 0x590 0x3 0x1
+#define IOMUXC_GPIO_AD_06_VIDEO_MUX_CSI_DATA15			0x124 0x368 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_06_GPIO_MUX3_IO05			0x124 0x368 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_06_ENET_1588_EVENT1_IN			0x124 0x368 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_06_FLEXIO2_D06				0x124 0x368 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_06_TMR4_TIMER2				0x124 0x368 0x668 0x9 0x0
+#define IOMUXC_GPIO_AD_06_GPIO9_IO05				0x124 0x368 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_06_FLEXPWM1_PWM0_X			0x124 0x368 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_07_USB_OTG2_PWR				0x128 0x36C 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_07_FLEXCAN1_RX				0x128 0x36C 0x498 0x1 0x0
+#define IOMUXC_GPIO_AD_07_EMVSIM2_CLK				0x128 0x36C 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_07_GPT3_CAPTURE2				0x128 0x36C 0x594 0x3 0x1
+#define IOMUXC_GPIO_AD_07_VIDEO_MUX_CSI_DATA14			0x128 0x36C 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_07_GPIO_MUX3_IO06			0x128 0x36C 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_07_ENET_1588_EVENT1_OUT			0x128 0x36C 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_07_FLEXIO2_D07				0x128 0x36C 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_07_TMR4_TIMER3				0x128 0x36C 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_07_GPIO9_IO06				0x128 0x36C 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_07_FLEXPWM1_PWM1_X			0x128 0x36C 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_08_USBPHY2_OTG_ID			0x12C 0x370 0x6C4 0x0 0x0
+#define IOMUXC_GPIO_AD_08_LPI2C1_SCL				0x12C 0x370 0x5AC 0x1 0x0
+#define IOMUXC_GPIO_AD_08_EMVSIM2_RST				0x12C 0x370 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_08_GPT3_COMPARE1				0x12C 0x370 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_08_VIDEO_MUX_CSI_DATA13			0x12C 0x370 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_08_GPIO_MUX3_IO07			0x12C 0x370 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_08_ENET_1588_EVENT2_IN			0x12C 0x370 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_08_FLEXIO2_D08				0x12C 0x370 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_08_GPIO9_IO07				0x12C 0x370 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_08_FLEXPWM1_PWM2_X			0x12C 0x370 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_09_USBPHY1_OTG_ID			0x130 0x374 0x6C0 0x0 0x0
+#define IOMUXC_GPIO_AD_09_LPI2C1_SDA				0x130 0x374 0x5B0 0x1 0x0
+#define IOMUXC_GPIO_AD_09_EMVSIM2_SVEN				0x130 0x374 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_09_GPT3_COMPARE2				0x130 0x374 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_09_VIDEO_MUX_CSI_DATA12			0x130 0x374 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_09_GPIO_MUX3_IO08			0x130 0x374 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_09_ENET_1588_EVENT2_OUT			0x130 0x374 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_09_FLEXIO2_D09				0x130 0x374 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_09_GPIO9_IO08				0x130 0x374 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_09_FLEXPWM1_PWM3_X			0x130 0x374 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_10_USB_OTG1_PWR				0x134 0x378 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_10_LPI2C1_SCLS				0x134 0x378 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_10_EMVSIM2_PD				0x134 0x378 0x6AC 0x2 0x0
+#define IOMUXC_GPIO_AD_10_GPT3_COMPARE3				0x134 0x378 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_10_VIDEO_MUX_CSI_DATA11			0x134 0x378 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_10_GPIO_MUX3_IO09			0x134 0x378 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_10_ENET_1588_EVENT3_IN			0x134 0x378 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_10_FLEXIO2_D10				0x134 0x378 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_10_GPIO9_IO09				0x134 0x378 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_10_FLEXPWM2_PWM0_X			0x134 0x378 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_11_USB_OTG1_OC				0x138 0x37C 0x6BC 0x0 0x0
+#define IOMUXC_GPIO_AD_11_LPI2C1_SDAS				0x138 0x37C 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_11_EMVSIM2_POWER_FAIL			0x138 0x37C 0x6B0 0x2 0x0
+#define IOMUXC_GPIO_AD_11_GPT3_CLK				0x138 0x37C 0x598 0x3 0x1
+#define IOMUXC_GPIO_AD_11_VIDEO_MUX_CSI_DATA10			0x138 0x37C 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_11_GPIO_MUX3_IO10			0x138 0x37C 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_11_ENET_1588_EVENT3_OUT			0x138 0x37C 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_11_FLEXIO2_D11				0x138 0x37C 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_11_GPIO9_IO10				0x138 0x37C 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_11_FLEXPWM2_PWM1_X			0x138 0x37C 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_12_SPDIF_LOCK				0x13C 0x380 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_12_LPI2C1_HREQ				0x13C 0x380 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_12_GPT1_CAPTURE1				0x13C 0x380 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_12_FLEXSPI1_B_DATA03			0x13C 0x380 0x570 0x3 0x0
+#define IOMUXC_GPIO_AD_12_VIDEO_MUX_CSI_PIXCLK			0x13C 0x380 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_12_GPIO_MUX3_IO11			0x13C 0x380 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_12_ENET_TX_DATA03			0x13C 0x380 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_12_FLEXIO2_D12				0x13C 0x380 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_12_EWM_OUT_B				0x13C 0x380 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_12_GPIO9_IO11				0x13C 0x380 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_12_FLEXPWM2_PWM2_X			0x13C 0x380 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_13_SPDIF_SR_CLK				0x140 0x384 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_13_PIT1_TRIGGER0				0x140 0x384 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_13_GPT1_CAPTURE2				0x140 0x384 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_13_FLEXSPI1_B_DATA02			0x140 0x384 0x56C 0x3 0x0
+#define IOMUXC_GPIO_AD_13_VIDEO_MUX_CSI_MCLK			0x140 0x384 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_13_GPIO_MUX3_IO12			0x140 0x384 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_13_ENET_TX_DATA02			0x140 0x384 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_13_FLEXIO2_D13				0x140 0x384 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_13_REF_CLK_32K				0x140 0x384 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_13_GPIO9_IO12				0x140 0x384 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_13_FLEXPWM2_PWM3_X			0x140 0x384 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_14_SPDIF_EXT_CLK				0x144 0x388 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_14_REF_CLK_24M				0x144 0x388 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_14_GPT1_COMPARE1				0x144 0x388 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_14_FLEXSPI1_B_DATA01			0x144 0x388 0x568 0x3 0x0
+#define IOMUXC_GPIO_AD_14_VIDEO_MUX_CSI_VSYNC			0x144 0x388 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_14_GPIO_MUX3_IO13			0x144 0x388 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_14_ENET_RX_CLK				0x144 0x388 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_14_FLEXIO2_D14				0x144 0x388 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_14_CCM_ENET_REF_CLK_25M			0x144 0x388 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_14_GPIO9_IO13				0x144 0x388 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_14_FLEXPWM3_PWM0_X			0x144 0x388 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_15_GPIO9_IO14				0x148 0x38C 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_15_FLEXPWM3_PWM1_X			0x148 0x38C 0x0 0xB 0x0
+#define IOMUXC_GPIO_AD_15_SPDIF_IN				0x148 0x38C 0x6B4 0x0 0x1
+#define IOMUXC_GPIO_AD_15_LPUART10_TXD				0x148 0x38C 0x628 0x1 0x0
+#define IOMUXC_GPIO_AD_15_GPT1_COMPARE2				0x148 0x38C 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_15_FLEXSPI1_B_DATA00			0x148 0x38C 0x564 0x3 0x0
+#define IOMUXC_GPIO_AD_15_VIDEO_MUX_CSI_HSYNC			0x148 0x38C 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_15_GPIO_MUX3_IO14			0x148 0x38C 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_15_ENET_TX_ER				0x148 0x38C 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_15_FLEXIO2_D15				0x148 0x38C 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_AD_16_SPDIF_OUT				0x14C 0x390 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_16_LPUART10_RXD				0x14C 0x390 0x624 0x1 0x0
+#define IOMUXC_GPIO_AD_16_GPT1_COMPARE3				0x14C 0x390 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_16_FLEXSPI1_B_SCLK			0x14C 0x390 0x578 0x3 0x0
+#define IOMUXC_GPIO_AD_16_VIDEO_MUX_CSI_DATA09			0x14C 0x390 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_16_GPIO_MUX3_IO15			0x14C 0x390 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_16_ENET_RX_DATA03			0x14C 0x390 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_16_FLEXIO2_D16				0x14C 0x390 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_16_ENET_1G_MDC				0x14C 0x390 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_16_GPIO9_IO15				0x14C 0x390 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_16_FLEXPWM3_PWM2_X			0x14C 0x390 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_17_SAI1_MCLK				0x150 0x394 0x66C 0x0 0x0
+#define IOMUXC_GPIO_AD_17_ACMP1_OUT				0x150 0x394 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_17_GPT1_CLK				0x150 0x394 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_17_FLEXSPI1_A_DQS			0x150 0x394 0x550 0x3 0x1
+#define IOMUXC_GPIO_AD_17_VIDEO_MUX_CSI_DATA08			0x150 0x394 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_17_GPIO_MUX3_IO16			0x150 0x394 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_17_ENET_RX_DATA02			0x150 0x394 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_17_FLEXIO2_D17				0x150 0x394 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_17_ENET_1G_MDIO				0x150 0x394 0x4C8 0x9 0x2
+#define IOMUXC_GPIO_AD_17_GPIO9_IO16				0x150 0x394 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_17_FLEXPWM3_PWM3_X			0x150 0x394 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_18_GPIO9_IO17				0x154 0x398 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_18_FLEXPWM4_PWM0_X			0x154 0x398 0x0 0xB 0x0
+#define IOMUXC_GPIO_AD_18_SAI1_RX_SYNC				0x154 0x398 0x678 0x0 0x0
+#define IOMUXC_GPIO_AD_18_ACMP2_OUT				0x154 0x398 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_18_LPSPI1_PCS1				0x154 0x398 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_18_FLEXSPI1_A_SS0_B			0x154 0x398 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_18_VIDEO_MUX_CSI_DATA07			0x154 0x398 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_18_GPIO_MUX3_IO17			0x154 0x398 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_18_ENET_CRS				0x154 0x398 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_18_FLEXIO2_D18				0x154 0x398 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_18_LPI2C2_SCL				0x154 0x398 0x5B4 0x9 0x1
+
+#define IOMUXC_GPIO_AD_19_SAI1_RX_BCLK				0x158 0x39C 0x670 0x0 0x0
+#define IOMUXC_GPIO_AD_19_ACMP3_OUT				0x158 0x39C 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_19_LPSPI1_PCS2				0x158 0x39C 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_19_FLEXSPI1_A_SCLK			0x158 0x39C 0x574 0x3 0x0
+#define IOMUXC_GPIO_AD_19_VIDEO_MUX_CSI_DATA06			0x158 0x39C 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_19_GPIO_MUX3_IO18			0x158 0x39C 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_19_ENET_COL				0x158 0x39C 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_19_FLEXIO2_D19				0x158 0x39C 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_19_LPI2C2_SDA				0x158 0x39C 0x5B8 0x9 0x1
+#define IOMUXC_GPIO_AD_19_GPIO9_IO18				0x158 0x39C 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_19_FLEXPWM4_PWM1_X			0x158 0x39C 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_20_SAI1_RX_DATA00			0x15C 0x3A0 0x674 0x0 0x0
+#define IOMUXC_GPIO_AD_20_ACMP4_OUT				0x15C 0x3A0 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_20_LPSPI1_PCS3				0x15C 0x3A0 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_20_FLEXSPI1_A_DATA00			0x15C 0x3A0 0x554 0x3 0x0
+#define IOMUXC_GPIO_AD_20_VIDEO_MUX_CSI_DATA05			0x15C 0x3A0 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_20_GPIO_MUX3_IO19			0x15C 0x3A0 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_20_KPP_ROW07				0x15C 0x3A0 0x5A8 0x6 0x0
+#define IOMUXC_GPIO_AD_20_FLEXIO2_D20				0x15C 0x3A0 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_20_ENET_QOS_1588_EVENT2_OUT		0x15C 0x3A0 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_20_GPIO9_IO19				0x15C 0x3A0 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_20_FLEXPWM4_PWM2_X			0x15C 0x3A0 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_21_SAI1_TX_DATA00			0x160 0x3A4 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_21_LPSPI2_PCS1				0x160 0x3A4 0x5E0 0x2 0x0
+#define IOMUXC_GPIO_AD_21_FLEXSPI1_A_DATA01			0x160 0x3A4 0x558 0x3 0x0
+#define IOMUXC_GPIO_AD_21_VIDEO_MUX_CSI_DATA04			0x160 0x3A4 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_21_GPIO_MUX3_IO20			0x160 0x3A4 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_21_KPP_COL07				0x160 0x3A4 0x5A0 0x6 0x0
+#define IOMUXC_GPIO_AD_21_FLEXIO2_D21				0x160 0x3A4 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_21_ENET_QOS_1588_EVENT2_IN		0x160 0x3A4 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_21_GPIO9_IO20				0x160 0x3A4 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_21_FLEXPWM4_PWM3_X			0x160 0x3A4 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_22_GPIO9_IO21				0x164 0x3A8 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_22_SAI1_TX_BCLK				0x164 0x3A8 0x67C 0x0 0x0
+#define IOMUXC_GPIO_AD_22_LPSPI2_PCS2				0x164 0x3A8 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_22_FLEXSPI1_A_DATA02			0x164 0x3A8 0x55C 0x3 0x0
+#define IOMUXC_GPIO_AD_22_VIDEO_MUX_CSI_DATA03			0x164 0x3A8 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_22_GPIO_MUX3_IO21			0x164 0x3A8 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_22_KPP_ROW06				0x164 0x3A8 0x5A4 0x6 0x0
+#define IOMUXC_GPIO_AD_22_FLEXIO2_D22				0x164 0x3A8 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_22_ENET_QOS_1588_EVENT3_OUT		0x164 0x3A8 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_AD_23_SAI1_TX_SYNC				0x168 0x3AC 0x680 0x0 0x0
+#define IOMUXC_GPIO_AD_23_LPSPI2_PCS3				0x168 0x3AC 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_23_FLEXSPI1_A_DATA03			0x168 0x3AC 0x560 0x3 0x0
+#define IOMUXC_GPIO_AD_23_VIDEO_MUX_CSI_DATA02			0x168 0x3AC 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_23_GPIO_MUX3_IO22			0x168 0x3AC 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_23_KPP_COL06				0x168 0x3AC 0x59C 0x6 0x0
+#define IOMUXC_GPIO_AD_23_FLEXIO2_D23				0x168 0x3AC 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_23_ENET_QOS_1588_EVENT3_IN		0x168 0x3AC 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_23_GPIO9_IO22				0x168 0x3AC 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_AD_24_LPUART1_TXD				0x16C 0x3B0 0x620 0x0 0x0
+#define IOMUXC_GPIO_AD_24_LPSPI2_SCK				0x16C 0x3B0 0x5E4 0x1 0x0
+#define IOMUXC_GPIO_AD_24_VIDEO_MUX_CSI_DATA00			0x16C 0x3B0 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_24_ENET_RX_EN				0x16C 0x3B0 0x4B8 0x3 0x0
+#define IOMUXC_GPIO_AD_24_FLEXPWM2_PWM0_A			0x16C 0x3B0 0x518 0x4 0x1
+#define IOMUXC_GPIO_AD_24_GPIO_MUX3_IO23			0x16C 0x3B0 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_24_KPP_ROW05				0x16C 0x3B0 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_24_FLEXIO2_D24				0x16C 0x3B0 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_24_LPI2C4_SCL				0x16C 0x3B0 0x5C4 0x9 0x0
+#define IOMUXC_GPIO_AD_24_GPIO9_IO23				0x16C 0x3B0 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_AD_25_GPIO9_IO24				0x170 0x3B4 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_25_LPUART1_RXD				0x170 0x3B4 0x61C 0x0 0x0
+#define IOMUXC_GPIO_AD_25_LPSPI2_PCS0				0x170 0x3B4 0x5DC 0x1 0x0
+#define IOMUXC_GPIO_AD_25_VIDEO_MUX_CSI_DATA01			0x170 0x3B4 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_25_ENET_RX_ER				0x170 0x3B4 0x4BC 0x3 0x0
+#define IOMUXC_GPIO_AD_25_FLEXPWM2_PWM0_B			0x170 0x3B4 0x524 0x4 0x1
+#define IOMUXC_GPIO_AD_25_GPIO_MUX3_IO24			0x170 0x3B4 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_25_KPP_COL05				0x170 0x3B4 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_25_FLEXIO2_D25				0x170 0x3B4 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_25_LPI2C4_SDA				0x170 0x3B4 0x5C8 0x9 0x0
+
+#define IOMUXC_GPIO_AD_26_LPUART1_CTS_B				0x174 0x3B8 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_26_LPSPI2_SOUT				0x174 0x3B8 0x5EC 0x1 0x0
+#define IOMUXC_GPIO_AD_26_SEMC_CSX01				0x174 0x3B8 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_26_ENET_RX_DATA00			0x174 0x3B8 0x4B0 0x3 0x0
+#define IOMUXC_GPIO_AD_26_FLEXPWM2_PWM1_A			0x174 0x3B8 0x51C 0x4 0x1
+#define IOMUXC_GPIO_AD_26_GPIO_MUX3_IO25			0x174 0x3B8 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_26_KPP_ROW04				0x174 0x3B8 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_26_FLEXIO2_D26				0x174 0x3B8 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_26_ENET_QOS_MDC				0x174 0x3B8 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_26_GPIO9_IO25				0x174 0x3B8 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_26_USDHC2_CD_B				0x174 0x3B8 0x6D0 0xB 0x1
+
+#define IOMUXC_GPIO_AD_27_LPUART1_RTS_B				0x178 0x3BC 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_27_LPSPI2_SIN				0x178 0x3BC 0x5E8 0x1 0x0
+#define IOMUXC_GPIO_AD_27_SEMC_CSX02				0x178 0x3BC 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_27_ENET_RX_DATA01			0x178 0x3BC 0x4B4 0x3 0x0
+#define IOMUXC_GPIO_AD_27_FLEXPWM2_PWM1_B			0x178 0x3BC 0x528 0x4 0x1
+#define IOMUXC_GPIO_AD_27_GPIO_MUX3_IO26			0x178 0x3BC 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_27_KPP_COL04				0x178 0x3BC 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_27_FLEXIO2_D27				0x178 0x3BC 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_27_ENET_QOS_MDIO				0x178 0x3BC 0x4EC 0x9 0x1
+#define IOMUXC_GPIO_AD_27_GPIO9_IO26				0x178 0x3BC 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_27_USDHC2_WP				0x178 0x3BC 0x6D4 0xB 0x1
+
+#define IOMUXC_GPIO_AD_28_GPIO9_IO27				0x17C 0x3C0 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_28_USDHC2_VSELECT			0x17C 0x3C0 0x0 0xB 0x0
+#define IOMUXC_GPIO_AD_28_LPSPI1_SCK				0x17C 0x3C0 0x5D0 0x0 0x1
+#define IOMUXC_GPIO_AD_28_LPUART5_TXD				0x17C 0x3C0 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_28_SEMC_CSX03				0x17C 0x3C0 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_28_ENET_TX_EN				0x17C 0x3C0 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_28_FLEXPWM2_PWM2_A			0x17C 0x3C0 0x520 0x4 0x1
+#define IOMUXC_GPIO_AD_28_GPIO_MUX3_IO27			0x17C 0x3C0 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_28_KPP_ROW03				0x17C 0x3C0 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_28_FLEXIO2_D28				0x17C 0x3C0 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_28_VIDEO_MUX_EXT_DCIC1			0x17C 0x3C0 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_AD_29_LPSPI1_PCS0				0x180 0x3C4 0x5CC 0x0 0x1
+#define IOMUXC_GPIO_AD_29_LPUART5_RXD				0x180 0x3C4 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_29_ENET_REF_CLK				0x180 0x3C4 0x4A8 0x2 0x0
+#define IOMUXC_GPIO_AD_29_ENET_TX_CLK				0x180 0x3C4 0x4C0 0x3 0x0
+#define IOMUXC_GPIO_AD_29_FLEXPWM2_PWM2_B			0x180 0x3C4 0x52C 0x4 0x1
+#define IOMUXC_GPIO_AD_29_GPIO_MUX3_IO28			0x180 0x3C4 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_29_KPP_COL03				0x180 0x3C4 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_29_FLEXIO2_D29				0x180 0x3C4 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_29_VIDEO_MUX_EXT_DCIC2			0x180 0x3C4 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_29_GPIO9_IO28				0x180 0x3C4 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_29_USDHC2_RESET_B			0x180 0x3C4 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_30_LPSPI1_SOUT				0x184 0x3C8 0x5D8 0x0 0x1
+#define IOMUXC_GPIO_AD_30_USB_OTG2_OC				0x184 0x3C8 0x6B8 0x1 0x1
+#define IOMUXC_GPIO_AD_30_FLEXCAN2_TX				0x184 0x3C8 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_30_ENET_TX_DATA00			0x184 0x3C8 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_30_LPUART3_TXD				0x184 0x3C8 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_30_GPIO_MUX3_IO29			0x184 0x3C8 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_30_KPP_ROW02				0x184 0x3C8 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_30_FLEXIO2_D30				0x184 0x3C8 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_30_WDOG2_RESET_B_DEB			0x184 0x3C8 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_30_GPIO9_IO29				0x184 0x3C8 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_AD_31_LPSPI1_SIN				0x188 0x3CC 0x5D4 0x0 0x1
+#define IOMUXC_GPIO_AD_31_USB_OTG2_PWR				0x188 0x3CC 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_31_FLEXCAN2_RX				0x188 0x3CC 0x49C 0x2 0x1
+#define IOMUXC_GPIO_AD_31_ENET_TX_DATA01			0x188 0x3CC 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_31_LPUART3_RXD				0x188 0x3CC 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_31_GPIO_MUX3_IO30			0x188 0x3CC 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_31_KPP_COL02				0x188 0x3CC 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_31_FLEXIO2_D31				0x188 0x3CC 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_31_WDOG1_RESET_B_DEB			0x188 0x3CC 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_31_GPIO9_IO30				0x188 0x3CC 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_AD_32_GPIO9_IO31				0x18C 0x3D0 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_32_LPI2C1_SCL				0x18C 0x3D0 0x5AC 0x0 0x1
+#define IOMUXC_GPIO_AD_32_USBPHY2_OTG_ID			0x18C 0x3D0 0x6C4 0x1 0x1
+#define IOMUXC_GPIO_AD_32_PGMC_PMIC_RDY				0x18C 0x3D0 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_32_ENET_MDC				0x18C 0x3D0 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_32_USDHC1_CD_B				0x18C 0x3D0 0x6C8 0x4 0x0
+#define IOMUXC_GPIO_AD_32_GPIO_MUX3_IO31			0x18C 0x3D0 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_32_KPP_ROW01				0x18C 0x3D0 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_32_LPUART10_TXD				0x18C 0x3D0 0x628 0x8 0x1
+#define IOMUXC_GPIO_AD_32_ENET_1G_MDC				0x18C 0x3D0 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_AD_33_LPI2C1_SDA				0x190 0x3D4 0x5B0 0x0 0x1
+#define IOMUXC_GPIO_AD_33_USBPHY1_OTG_ID			0x190 0x3D4 0x6C0 0x1 0x1
+#define IOMUXC_GPIO_AD_33_XBAR1_INOUT17				0x190 0x3D4 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_33_ENET_MDIO				0x190 0x3D4 0x4AC 0x3 0x1
+#define IOMUXC_GPIO_AD_33_USDHC1_WP				0x190 0x3D4 0x6CC 0x4 0x0
+#define IOMUXC_GPIO_AD_33_GPIO_MUX4_IO00			0x190 0x3D4 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_33_KPP_COL01				0x190 0x3D4 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_33_LPUART10_RXD				0x190 0x3D4 0x624 0x8 0x1
+#define IOMUXC_GPIO_AD_33_ENET_1G_MDIO				0x190 0x3D4 0x4C8 0x9 0x3
+#define IOMUXC_GPIO_AD_33_GPIO10_IO00				0x190 0x3D4 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_AD_34_ENET_1G_1588_EVENT0_IN		0x194 0x3D8 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_34_USB_OTG1_PWR				0x194 0x3D8 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_34_XBAR1_INOUT18				0x194 0x3D8 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_34_ENET_1588_EVENT0_IN			0x194 0x3D8 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_34_USDHC1_VSELECT			0x194 0x3D8 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_34_GPIO_MUX4_IO01			0x194 0x3D8 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_34_KPP_ROW00				0x194 0x3D8 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_34_LPUART10_CTS_B			0x194 0x3D8 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_34_WDOG1_ANY				0x194 0x3D8 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_34_GPIO10_IO01				0x194 0x3D8 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_AD_35_GPIO10_IO02				0x198 0x3DC 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_35_ENET_1G_1588_EVENT0_OUT		0x198 0x3DC 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_35_USB_OTG1_OC				0x198 0x3DC 0x6BC 0x1 0x1
+#define IOMUXC_GPIO_AD_35_XBAR1_INOUT19				0x198 0x3DC 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_35_ENET_1588_EVENT0_OUT			0x198 0x3DC 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_35_USDHC1_RESET_B			0x198 0x3DC 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_35_GPIO_MUX4_IO02			0x198 0x3DC 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_35_KPP_COL00				0x198 0x3DC 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_35_LPUART10_RTS_B			0x198 0x3DC 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_35_FLEXSPI1_B_SS1_B			0x198 0x3DC 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_SD_B1_00_USDHC1_CMD				0x19C 0x3E0 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B1_00_XBAR1_INOUT20			0x19C 0x3E0 0x6D8 0x2 0x1
+#define IOMUXC_GPIO_SD_B1_00_GPT4_CAPTURE1			0x19C 0x3E0 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B1_00_GPIO_MUX4_IO03			0x19C 0x3E0 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B1_00_FLEXSPI2_A_SS0_B			0x19C 0x3E0 0x0 0x6 0x0
+#define IOMUXC_GPIO_SD_B1_00_KPP_ROW07				0x19C 0x3E0 0x5A8 0x8 0x1
+#define IOMUXC_GPIO_SD_B1_00_GPIO10_IO03			0x19C 0x3E0 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_SD_B1_01_USDHC1_CLK				0x1A0 0x3E4 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B1_01_XBAR1_INOUT21			0x1A0 0x3E4 0x6DC 0x2 0x1
+#define IOMUXC_GPIO_SD_B1_01_GPT4_CAPTURE2			0x1A0 0x3E4 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B1_01_GPIO_MUX4_IO04			0x1A0 0x3E4 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B1_01_FLEXSPI2_A_SCLK			0x1A0 0x3E4 0x58C 0x6 0x1
+#define IOMUXC_GPIO_SD_B1_01_KPP_COL07				0x1A0 0x3E4 0x5A0 0x8 0x1
+#define IOMUXC_GPIO_SD_B1_01_GPIO10_IO04			0x1A0 0x3E4 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_SD_B1_02_GPIO10_IO05			0x1A4 0x3E8 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B1_02_USDHC1_DATA0			0x1A4 0x3E8 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B1_02_XBAR1_INOUT22			0x1A4 0x3E8 0x6E0 0x2 0x1
+#define IOMUXC_GPIO_SD_B1_02_GPT4_COMPARE1			0x1A4 0x3E8 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B1_02_GPIO_MUX4_IO05			0x1A4 0x3E8 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B1_02_FLEXSPI2_A_DATA00			0x1A4 0x3E8 0x57C 0x6 0x1
+#define IOMUXC_GPIO_SD_B1_02_KPP_ROW06				0x1A4 0x3E8 0x5A4 0x8 0x1
+#define IOMUXC_GPIO_SD_B1_02_FLEXSPI1_A_SS1_B			0x1A4 0x3E8 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_SD_B1_03_USDHC1_DATA1			0x1A8 0x3EC 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B1_03_XBAR1_INOUT23			0x1A8 0x3EC 0x6E4 0x2 0x1
+#define IOMUXC_GPIO_SD_B1_03_GPT4_COMPARE2			0x1A8 0x3EC 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B1_03_GPIO_MUX4_IO06			0x1A8 0x3EC 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B1_03_FLEXSPI2_A_DATA01			0x1A8 0x3EC 0x580 0x6 0x1
+#define IOMUXC_GPIO_SD_B1_03_KPP_COL06				0x1A8 0x3EC 0x59C 0x8 0x1
+#define IOMUXC_GPIO_SD_B1_03_FLEXSPI1_B_SS1_B			0x1A8 0x3EC 0x0 0x9 0x0
+#define IOMUXC_GPIO_SD_B1_03_GPIO10_IO06			0x1A8 0x3EC 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_SD_B1_04_USDHC1_DATA2			0x1AC 0x3F0 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B1_04_XBAR1_INOUT24			0x1AC 0x3F0 0x6E8 0x2 0x1
+#define IOMUXC_GPIO_SD_B1_04_GPT4_COMPARE3			0x1AC 0x3F0 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B1_04_GPIO_MUX4_IO07			0x1AC 0x3F0 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B1_04_FLEXSPI2_A_DATA02			0x1AC 0x3F0 0x584 0x6 0x1
+#define IOMUXC_GPIO_SD_B1_04_FLEXSPI1_B_SS0_B			0x1AC 0x3F0 0x0 0x8 0x0
+#define IOMUXC_GPIO_SD_B1_04_ENET_QOS_1588_EVENT2_AUX_IN	0x1AC 0x3F0 0x0 0x9 0x0
+#define IOMUXC_GPIO_SD_B1_04_GPIO10_IO07			0x1AC 0x3F0 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_SD_B1_05_GPIO10_IO08			0x1B0 0x3F4 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B1_05_USDHC1_DATA3			0x1B0 0x3F4 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B1_05_XBAR1_INOUT25			0x1B0 0x3F4 0x6EC 0x2 0x1
+#define IOMUXC_GPIO_SD_B1_05_GPT4_CLK				0x1B0 0x3F4 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B1_05_GPIO_MUX4_IO08			0x1B0 0x3F4 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B1_05_FLEXSPI2_A_DATA03			0x1B0 0x3F4 0x588 0x6 0x1
+#define IOMUXC_GPIO_SD_B1_05_FLEXSPI1_B_DQS			0x1B0 0x3F4 0x0 0x8 0x0
+#define IOMUXC_GPIO_SD_B1_05_ENET_QOS_1588_EVENT3_AUX_IN	0x1B0 0x3F4 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_SD_B2_00_GPIO10_IO09			0x1B4 0x3F8 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B2_00_USDHC2_DATA3			0x1B4 0x3F8 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_00_FLEXSPI1_B_DATA03			0x1B4 0x3F8 0x570 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_00_ENET_1G_RX_EN			0x1B4 0x3F8 0x4E0 0x2 0x1
+#define IOMUXC_GPIO_SD_B2_00_LPUART9_TXD			0x1B4 0x3F8 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_00_LPSPI4_SCK				0x1B4 0x3F8 0x610 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_00_GPIO_MUX4_IO09			0x1B4 0x3F8 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SD_B2_01_USDHC2_DATA2			0x1B8 0x3FC 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_01_FLEXSPI1_B_DATA02			0x1B8 0x3FC 0x56C 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_01_ENET_1G_RX_CLK			0x1B8 0x3FC 0x4CC 0x2 0x1
+#define IOMUXC_GPIO_SD_B2_01_LPUART9_RXD			0x1B8 0x3FC 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_01_LPSPI4_PCS0			0x1B8 0x3FC 0x60C 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_01_GPIO_MUX4_IO10			0x1B8 0x3FC 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B2_01_GPIO10_IO10			0x1B8 0x3FC 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_SD_B2_02_GPIO10_IO11			0x1BC 0x400 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B2_02_USDHC2_DATA1			0x1BC 0x400 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_02_FLEXSPI1_B_DATA01			0x1BC 0x400 0x568 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_02_ENET_1G_RX_DATA00			0x1BC 0x400 0x4D0 0x2 0x1
+#define IOMUXC_GPIO_SD_B2_02_LPUART9_CTS_B			0x1BC 0x400 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_02_LPSPI4_SOUT			0x1BC 0x400 0x618 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_02_GPIO_MUX4_IO11			0x1BC 0x400 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SD_B2_03_GPIO10_IO12			0x1C0 0x404 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B2_03_USDHC2_DATA0			0x1C0 0x404 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_03_FLEXSPI1_B_DATA00			0x1C0 0x404 0x564 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_03_ENET_1G_RX_DATA01			0x1C0 0x404 0x4D4 0x2 0x1
+#define IOMUXC_GPIO_SD_B2_03_LPUART9_RTS_B			0x1C0 0x404 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_03_LPSPI4_SIN				0x1C0 0x404 0x614 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_03_GPIO_MUX4_IO12			0x1C0 0x404 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SD_B2_04_USDHC2_CLK				0x1C4 0x408 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_04_FLEXSPI1_B_SCLK			0x1C4 0x408 0x578 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_04_ENET_1G_RX_DATA02			0x1C4 0x408 0x4D8 0x2 0x1
+#define IOMUXC_GPIO_SD_B2_04_FLEXSPI1_A_SS1_B			0x1C4 0x408 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_04_LPSPI4_PCS1			0x1C4 0x408 0x0 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_04_GPIO_MUX4_IO13			0x1C4 0x408 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B2_04_GPIO10_IO13			0x1C4 0x408 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_SD_B2_05_GPIO10_IO14			0x1C8 0x40C 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B2_05_USDHC2_CMD				0x1C8 0x40C 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_05_FLEXSPI1_A_DQS			0x1C8 0x40C 0x550 0x1 0x2
+#define IOMUXC_GPIO_SD_B2_05_ENET_1G_RX_DATA03			0x1C8 0x40C 0x4DC 0x2 0x1
+#define IOMUXC_GPIO_SD_B2_05_FLEXSPI1_B_SS0_B			0x1C8 0x40C 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_05_LPSPI4_PCS2			0x1C8 0x40C 0x0 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_05_GPIO_MUX4_IO14			0x1C8 0x40C 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SD_B2_06_GPIO10_IO15			0x1CC 0x410 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B2_06_USDHC2_RESET_B			0x1CC 0x410 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_06_FLEXSPI1_A_SS0_B			0x1CC 0x410 0x0 0x1 0x0
+#define IOMUXC_GPIO_SD_B2_06_ENET_1G_TX_DATA03			0x1CC 0x410 0x0 0x2 0x0
+#define IOMUXC_GPIO_SD_B2_06_LPSPI4_PCS3			0x1CC 0x410 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_06_GPT6_CAPTURE1			0x1CC 0x410 0x0 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_06_GPIO_MUX4_IO15			0x1CC 0x410 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SD_B2_07_USDHC2_STROBE			0x1D0 0x414 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_07_FLEXSPI1_A_SCLK			0x1D0 0x414 0x574 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_07_ENET_1G_TX_DATA02			0x1D0 0x414 0x0 0x2 0x0
+#define IOMUXC_GPIO_SD_B2_07_LPUART3_CTS_B			0x1D0 0x414 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_07_GPT6_CAPTURE2			0x1D0 0x414 0x0 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_07_GPIO_MUX4_IO16			0x1D0 0x414 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B2_07_LPSPI2_SCK				0x1D0 0x414 0x5E4 0x6 0x1
+#define IOMUXC_GPIO_SD_B2_07_ENET_TX_ER				0x1D0 0x414 0x0 0x8 0x0
+#define IOMUXC_GPIO_SD_B2_07_ENET_QOS_REF_CLK			0x1D0 0x414 0x4A0 0x9 0x1
+#define IOMUXC_GPIO_SD_B2_07_GPIO10_IO16			0x1D0 0x414 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_SD_B2_08_GPIO10_IO17			0x1D4 0x418 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B2_08_USDHC2_DATA4			0x1D4 0x418 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_08_FLEXSPI1_A_DATA00			0x1D4 0x418 0x554 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_08_ENET_1G_TX_DATA01			0x1D4 0x418 0x0 0x2 0x0
+#define IOMUXC_GPIO_SD_B2_08_LPUART3_RTS_B			0x1D4 0x418 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_08_GPT6_COMPARE1			0x1D4 0x418 0x0 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_08_GPIO_MUX4_IO17			0x1D4 0x418 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B2_08_LPSPI2_PCS0			0x1D4 0x418 0x5DC 0x6 0x1
+
+#define IOMUXC_GPIO_SD_B2_09_GPIO10_IO18			0x1D8 0x41C 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B2_09_USDHC2_DATA5			0x1D8 0x41C 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_09_FLEXSPI1_A_DATA01			0x1D8 0x41C 0x558 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_09_ENET_1G_TX_DATA00			0x1D8 0x41C 0x0 0x2 0x0
+#define IOMUXC_GPIO_SD_B2_09_LPUART5_CTS_B			0x1D8 0x41C 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_09_GPT6_COMPARE2			0x1D8 0x41C 0x0 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_09_GPIO_MUX4_IO18			0x1D8 0x41C 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B2_09_LPSPI2_SOUT			0x1D8 0x41C 0x5EC 0x6 0x1
+
+#define IOMUXC_GPIO_SD_B2_10_GPIO10_IO19			0x1DC 0x420 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B2_10_USDHC2_DATA6			0x1DC 0x420 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_10_FLEXSPI1_A_DATA02			0x1DC 0x420 0x55C 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_10_ENET_1G_TX_EN			0x1DC 0x420 0x0 0x2 0x0
+#define IOMUXC_GPIO_SD_B2_10_LPUART5_RTS_B			0x1DC 0x420 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_10_GPT6_COMPARE3			0x1DC 0x420 0x0 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_10_GPIO_MUX4_IO19			0x1DC 0x420 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B2_10_LPSPI2_SIN				0x1DC 0x420 0x5E8 0x6 0x1
+
+#define IOMUXC_GPIO_SD_B2_11_USDHC2_DATA7			0x1E0 0x424 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_11_FLEXSPI1_A_DATA03			0x1E0 0x424 0x560 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_11_ENET_1G_TX_CLK_IO			0x1E0 0x424 0x4E8 0x2 0x1
+#define IOMUXC_GPIO_SD_B2_11_ENET_1G_REF_CLK			0x1E0 0x424 0x4C4 0x3 0x1
+#define IOMUXC_GPIO_SD_B2_11_GPT6_CLK				0x1E0 0x424 0x0 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_11_GPIO_MUX4_IO20			0x1E0 0x424 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B2_11_LPSPI2_PCS1			0x1E0 0x424 0x5E0 0x6 0x1
+#define IOMUXC_GPIO_SD_B2_11_GPIO10_IO20			0x1E0 0x424 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B1_00_VIDEO_MUX_LCDIF_CLK		0x1E4 0x428 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_00_ENET_1G_RX_EN			0x1E4 0x428 0x4E0 0x1 0x2
+#define IOMUXC_GPIO_DISP_B1_00_TMR1_TIMER0			0x1E4 0x428 0x63C 0x3 0x2
+#define IOMUXC_GPIO_DISP_B1_00_XBAR1_INOUT26			0x1E4 0x428 0x6F0 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_00_GPIO_MUX4_IO21			0x1E4 0x428 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_00_ENET_QOS_RX_EN			0x1E4 0x428 0x4F8 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_00_GPIO10_IO21			0x1E4 0x428 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B1_01_VIDEO_MUX_LCDIF_ENABLE		0x1E8 0x42C 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_01_ENET_1G_RX_CLK			0x1E8 0x42C 0x4CC 0x1 0x2
+#define IOMUXC_GPIO_DISP_B1_01_ENET_1G_RX_ER			0x1E8 0x42C 0x4E4 0x2 0x1
+#define IOMUXC_GPIO_DISP_B1_01_TMR1_TIMER1			0x1E8 0x42C 0x640 0x3 0x2
+#define IOMUXC_GPIO_DISP_B1_01_XBAR1_INOUT27			0x1E8 0x42C 0x6F4 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_01_GPIO_MUX4_IO22			0x1E8 0x42C 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_01_ENET_QOS_RX_CLK			0x1E8 0x42C 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_01_ENET_QOS_RX_ER			0x1E8 0x42C 0x4FC 0x9 0x0
+#define IOMUXC_GPIO_DISP_B1_01_GPIO10_IO22			0x1E8 0x42C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B1_02_GPIO10_IO23			0x1EC 0x430 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B1_02_VIDEO_MUX_LCDIF_HSYNC		0x1EC 0x430 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_02_ENET_1G_RX_DATA00		0x1EC 0x430 0x4D0 0x1 0x2
+#define IOMUXC_GPIO_DISP_B1_02_LPI2C3_SCL			0x1EC 0x430 0x5BC 0x2 0x0
+#define IOMUXC_GPIO_DISP_B1_02_TMR1_TIMER2			0x1EC 0x430 0x644 0x3 0x1
+#define IOMUXC_GPIO_DISP_B1_02_XBAR1_INOUT28			0x1EC 0x430 0x6F8 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_02_GPIO_MUX4_IO23			0x1EC 0x430 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_02_ENET_QOS_RX_DATA00		0x1EC 0x430 0x4F0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_02_LPUART1_TXD			0x1EC 0x430 0x620 0x9 0x1
+
+#define IOMUXC_GPIO_DISP_B1_03_VIDEO_MUX_LCDIF_VSYNC		0x1F0 0x434 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_03_ENET_1G_RX_DATA01		0x1F0 0x434 0x4D4 0x1 0x2
+#define IOMUXC_GPIO_DISP_B1_03_LPI2C3_SDA			0x1F0 0x434 0x5C0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B1_03_TMR2_TIMER0			0x1F0 0x434 0x648 0x3 0x2
+#define IOMUXC_GPIO_DISP_B1_03_XBAR1_INOUT29			0x1F0 0x434 0x6FC 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_03_GPIO_MUX4_IO24			0x1F0 0x434 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_03_ENET_QOS_RX_DATA01		0x1F0 0x434 0x4F4 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_03_LPUART1_RXD			0x1F0 0x434 0x61C 0x9 0x1
+#define IOMUXC_GPIO_DISP_B1_03_GPIO10_IO24			0x1F0 0x434 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B1_04_VIDEO_MUX_LCDIF_DATA00		0x1F4 0x438 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_04_ENET_1G_RX_DATA02		0x1F4 0x438 0x4D8 0x1 0x2
+#define IOMUXC_GPIO_DISP_B1_04_LPUART4_RXD			0x1F4 0x438 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B1_04_TMR2_TIMER1			0x1F4 0x438 0x64C 0x3 0x2
+#define IOMUXC_GPIO_DISP_B1_04_XBAR1_INOUT30			0x1F4 0x438 0x700 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_04_GPIO_MUX4_IO25			0x1F4 0x438 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_04_ENET_QOS_RX_DATA02		0x1F4 0x438 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_04_LPSPI3_SCK			0x1F4 0x438 0x600 0x9 0x1
+#define IOMUXC_GPIO_DISP_B1_04_GPIO10_IO25			0x1F4 0x438 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B1_05_GPIO10_IO26			0x1F8 0x43C 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B1_05_VIDEO_MUX_LCDIF_DATA01		0x1F8 0x43C 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_05_ENET_1G_RX_DATA03		0x1F8 0x43C 0x4DC 0x1 0x2
+#define IOMUXC_GPIO_DISP_B1_05_LPUART4_CTS_B			0x1F8 0x43C 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B1_05_TMR2_TIMER2			0x1F8 0x43C 0x650 0x3 0x1
+#define IOMUXC_GPIO_DISP_B1_05_XBAR1_INOUT31			0x1F8 0x43C 0x704 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_05_GPIO_MUX4_IO26			0x1F8 0x43C 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_05_ENET_QOS_RX_DATA03		0x1F8 0x43C 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_05_LPSPI3_SIN			0x1F8 0x43C 0x604 0x9 0x1
+
+#define IOMUXC_GPIO_DISP_B1_06_VIDEO_MUX_LCDIF_DATA02		0x1FC 0x440 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_06_ENET_1G_TX_DATA03		0x1FC 0x440 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B1_06_LPUART4_TXD			0x1FC 0x440 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B1_06_TMR3_TIMER0			0x1FC 0x440 0x654 0x3 0x2
+#define IOMUXC_GPIO_DISP_B1_06_XBAR1_INOUT32			0x1FC 0x440 0x708 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_06_GPIO_MUX4_IO27			0x1FC 0x440 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_06_SRC_BT_CFG00			0x1FC 0x440 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B1_06_ENET_QOS_TX_DATA03		0x1FC 0x440 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_06_LPSPI3_SOUT			0x1FC 0x440 0x608 0x9 0x1
+#define IOMUXC_GPIO_DISP_B1_06_GPIO10_IO27			0x1FC 0x440 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B1_07_VIDEO_MUX_LCDIF_DATA03		0x200 0x444 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_07_ENET_1G_TX_DATA02		0x200 0x444 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B1_07_LPUART4_RTS_B			0x200 0x444 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B1_07_TMR3_TIMER1			0x200 0x444 0x658 0x3 0x2
+#define IOMUXC_GPIO_DISP_B1_07_XBAR1_INOUT33			0x200 0x444 0x70C 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_07_GPIO_MUX4_IO28			0x200 0x444 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_07_SRC_BT_CFG01			0x200 0x444 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B1_07_ENET_QOS_TX_DATA02		0x200 0x444 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_07_LPSPI3_PCS0			0x200 0x444 0x5F0 0x9 0x1
+#define IOMUXC_GPIO_DISP_B1_07_GPIO10_IO28			0x200 0x444 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B1_08_GPIO10_IO29			0x204 0x448 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B1_08_VIDEO_MUX_LCDIF_DATA04		0x204 0x448 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_08_ENET_1G_TX_DATA01		0x204 0x448 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B1_08_USDHC1_CD_B			0x204 0x448 0x6C8 0x2 0x1
+#define IOMUXC_GPIO_DISP_B1_08_TMR3_TIMER2			0x204 0x448 0x65C 0x3 0x1
+#define IOMUXC_GPIO_DISP_B1_08_XBAR1_INOUT34			0x204 0x448 0x710 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_08_GPIO_MUX4_IO29			0x204 0x448 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_08_SRC_BT_CFG02			0x204 0x448 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B1_08_ENET_QOS_TX_DATA01		0x204 0x448 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_08_LPSPI3_PCS1			0x204 0x448 0x5F4 0x9 0x1
+
+#define IOMUXC_GPIO_DISP_B1_09_VIDEO_MUX_LCDIF_DATA05		0x208 0x44C 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_09_ENET_1G_TX_DATA00		0x208 0x44C 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B1_09_USDHC1_WP			0x208 0x44C 0x6CC 0x2 0x1
+#define IOMUXC_GPIO_DISP_B1_09_TMR4_TIMER0			0x208 0x44C 0x660 0x3 0x2
+#define IOMUXC_GPIO_DISP_B1_09_XBAR1_INOUT35			0x208 0x44C 0x714 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_09_GPIO_MUX4_IO30			0x208 0x44C 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_09_SRC_BT_CFG03			0x208 0x44C 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B1_09_ENET_QOS_TX_DATA00		0x208 0x44C 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_09_LPSPI3_PCS2			0x208 0x44C 0x5F8 0x9 0x1
+#define IOMUXC_GPIO_DISP_B1_09_GPIO10_IO30			0x208 0x44C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B1_10_VIDEO_MUX_LCDIF_DATA06		0x20C 0x450 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_10_ENET_1G_TX_EN			0x20C 0x450 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B1_10_USDHC1_RESET_B			0x20C 0x450 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B1_10_TMR4_TIMER1			0x20C 0x450 0x664 0x3 0x2
+#define IOMUXC_GPIO_DISP_B1_10_XBAR1_INOUT36			0x20C 0x450 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B1_10_GPIO_MUX4_IO31			0x20C 0x450 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_10_SRC_BT_CFG04			0x20C 0x450 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B1_10_ENET_QOS_TX_EN			0x20C 0x450 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_10_LPSPI3_PCS3			0x20C 0x450 0x5FC 0x9 0x1
+#define IOMUXC_GPIO_DISP_B1_10_GPIO10_IO31			0x20C 0x450 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B1_11_VIDEO_MUX_LCDIF_DATA07		0x210 0x454 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_11_ENET_1G_TX_CLK_IO		0x210 0x454 0x4E8 0x1 0x2
+#define IOMUXC_GPIO_DISP_B1_11_ENET_1G_REF_CLK			0x210 0x454 0x4C4 0x2 0x2
+#define IOMUXC_GPIO_DISP_B1_11_TMR4_TIMER2			0x210 0x454 0x668 0x3 0x1
+#define IOMUXC_GPIO_DISP_B1_11_XBAR1_INOUT37			0x210 0x454 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B1_11_GPIO_MUX5_IO00			0x210 0x454 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_11_SRC_BT_CFG05			0x210 0x454 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B1_11_ENET_QOS_TX_CLK			0x210 0x454 0x4A4 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_11_ENET_QOS_REF_CLK			0x210 0x454 0x4A0 0x9 0x2
+#define IOMUXC_GPIO_DISP_B1_11_GPIO11_IO00			0x210 0x454 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B2_00_GPIO11_IO01			0x214 0x458 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_00_VIDEO_MUX_LCDIF_DATA08		0x214 0x458 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_00_WDOG1_B				0x214 0x458 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B2_00_MQS_RIGHT			0x214 0x458 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_00_ENET_1G_TX_ER			0x214 0x458 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_00_SAI1_TX_DATA03			0x214 0x458 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B2_00_GPIO_MUX5_IO01			0x214 0x458 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_00_SRC_BT_CFG06			0x214 0x458 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B2_00_ENET_QOS_TX_ER			0x214 0x458 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_DISP_B2_01_VIDEO_MUX_LCDIF_DATA09		0x218 0x45C 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_01_USDHC1_VSELECT			0x218 0x45C 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B2_01_MQS_LEFT				0x218 0x45C 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_01_WDOG2_B				0x218 0x45C 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_01_SAI1_TX_DATA02			0x218 0x45C 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B2_01_GPIO_MUX5_IO02			0x218 0x45C 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_01_SRC_BT_CFG07			0x218 0x45C 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B2_01_EWM_OUT_B			0x218 0x45C 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B2_01_CCM_ENET_REF_CLK_25M		0x218 0x45C 0x0 0x9 0x0
+#define IOMUXC_GPIO_DISP_B2_01_GPIO11_IO02			0x218 0x45C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B2_02_GPIO11_IO03			0x21C 0x460 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_02_VIDEO_MUX_LCDIF_DATA10		0x21C 0x460 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_02_ENET_TX_DATA00			0x21C 0x460 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B2_02_PIT1_TRIGGER3			0x21C 0x460 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_02_ARM_TRACE00			0x21C 0x460 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_02_SAI1_TX_DATA01			0x21C 0x460 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B2_02_GPIO_MUX5_IO03			0x21C 0x460 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_02_SRC_BT_CFG08			0x21C 0x460 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B2_02_ENET_QOS_TX_DATA00		0x21C 0x460 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_DISP_B2_03_GPIO11_IO04			0x220 0x464 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_03_VIDEO_MUX_LCDIF_DATA11		0x220 0x464 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_03_ENET_TX_DATA01			0x220 0x464 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B2_03_PIT1_TRIGGER2			0x220 0x464 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_03_ARM_TRACE01			0x220 0x464 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_03_SAI1_MCLK			0x220 0x464 0x66C 0x4 0x1
+#define IOMUXC_GPIO_DISP_B2_03_GPIO_MUX5_IO04			0x220 0x464 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_03_SRC_BT_CFG09			0x220 0x464 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B2_03_ENET_QOS_TX_DATA01		0x220 0x464 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_DISP_B2_04_VIDEO_MUX_LCDIF_DATA12		0x224 0x468 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_04_ENET_TX_EN			0x224 0x468 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B2_04_PIT1_TRIGGER1			0x224 0x468 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_04_ARM_TRACE02			0x224 0x468 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_04_SAI1_RX_SYNC			0x224 0x468 0x678 0x4 0x1
+#define IOMUXC_GPIO_DISP_B2_04_GPIO_MUX5_IO05			0x224 0x468 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_04_SRC_BT_CFG10			0x224 0x468 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B2_04_ENET_QOS_TX_EN			0x224 0x468 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B2_04_GPIO11_IO05			0x224 0x468 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B2_05_GPIO11_IO06			0x228 0x46C 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_05_VIDEO_MUX_LCDIF_DATA13		0x228 0x46C 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_05_ENET_TX_CLK			0x228 0x46C 0x4C0 0x1 0x1
+#define IOMUXC_GPIO_DISP_B2_05_ENET_REF_CLK			0x228 0x46C 0x4A8 0x2 0x1
+#define IOMUXC_GPIO_DISP_B2_05_ARM_TRACE03			0x228 0x46C 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_05_SAI1_RX_BCLK			0x228 0x46C 0x670 0x4 0x1
+#define IOMUXC_GPIO_DISP_B2_05_GPIO_MUX5_IO06			0x228 0x46C 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_05_SRC_BT_CFG11			0x228 0x46C 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B2_05_ENET_QOS_TX_CLK			0x228 0x46C 0x4A4 0x8 0x1
+
+#define IOMUXC_GPIO_DISP_B2_06_GPIO11_IO07			0x22C 0x470 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_06_VIDEO_MUX_LCDIF_DATA14		0x22C 0x470 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_06_ENET_RX_DATA00			0x22C 0x470 0x4B0 0x1 0x1
+#define IOMUXC_GPIO_DISP_B2_06_LPUART7_TXD			0x22C 0x470 0x630 0x2 0x1
+#define IOMUXC_GPIO_DISP_B2_06_ARM_TRACE_CLK			0x22C 0x470 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_06_SAI1_RX_DATA00			0x22C 0x470 0x674 0x4 0x1
+#define IOMUXC_GPIO_DISP_B2_06_GPIO_MUX5_IO07			0x22C 0x470 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_06_ENET_QOS_RX_DATA00		0x22C 0x470 0x4F0 0x8 0x1
+
+#define IOMUXC_GPIO_DISP_B2_07_VIDEO_MUX_LCDIF_DATA15		0x230 0x474 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_07_ENET_RX_DATA01			0x230 0x474 0x4B4 0x1 0x1
+#define IOMUXC_GPIO_DISP_B2_07_LPUART7_RXD			0x230 0x474 0x62C 0x2 0x1
+#define IOMUXC_GPIO_DISP_B2_07_ARM_TRACE_SWO			0x230 0x474 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_07_SAI1_TX_DATA00			0x230 0x474 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B2_07_GPIO_MUX5_IO08			0x230 0x474 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_07_ENET_QOS_RX_DATA01		0x230 0x474 0x4F4 0x8 0x1
+#define IOMUXC_GPIO_DISP_B2_07_GPIO11_IO08			0x230 0x474 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B2_08_GPIO11_IO09			0x234 0x478 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_08_VIDEO_MUX_LCDIF_DATA16		0x234 0x478 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_08_ENET_RX_EN			0x234 0x478 0x4B8 0x1 0x1
+#define IOMUXC_GPIO_DISP_B2_08_LPUART8_TXD			0x234 0x478 0x638 0x2 0x1
+#define IOMUXC_GPIO_DISP_B2_08_ARM_CM7_EVENTO			0x234 0x478 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_08_SAI1_TX_BCLK			0x234 0x478 0x67C 0x4 0x1
+#define IOMUXC_GPIO_DISP_B2_08_GPIO_MUX5_IO09			0x234 0x478 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_08_ENET_QOS_RX_EN			0x234 0x478 0x4F8 0x8 0x1
+#define IOMUXC_GPIO_DISP_B2_08_LPUART1_TXD			0x234 0x478 0x620 0x9 0x2
+
+#define IOMUXC_GPIO_DISP_B2_09_GPIO11_IO10			0x238 0x47C 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_09_VIDEO_MUX_LCDIF_DATA17		0x238 0x47C 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_09_ENET_RX_ER			0x238 0x47C 0x4BC 0x1 0x1
+#define IOMUXC_GPIO_DISP_B2_09_LPUART8_RXD			0x238 0x47C 0x634 0x2 0x1
+#define IOMUXC_GPIO_DISP_B2_09_ARM_CM7_EVENTI			0x238 0x47C 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_09_SAI1_TX_SYNC			0x238 0x47C 0x680 0x4 0x1
+#define IOMUXC_GPIO_DISP_B2_09_GPIO_MUX5_IO10			0x238 0x47C 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_09_ENET_QOS_RX_ER			0x238 0x47C 0x4FC 0x8 0x1
+#define IOMUXC_GPIO_DISP_B2_09_LPUART1_RXD			0x238 0x47C 0x61C 0x9 0x2
+
+#define IOMUXC_GPIO_DISP_B2_10_GPIO11_IO11			0x23C 0x480 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_10_VIDEO_MUX_LCDIF_DATA18		0x23C 0x480 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_10_EMVSIM2_IO			0x23C 0x480 0x6A8 0x1 0x1
+#define IOMUXC_GPIO_DISP_B2_10_LPUART2_TXD			0x23C 0x480 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_10_WDOG2_RESET_B_DEB		0x23C 0x480 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_10_XBAR1_INOUT38			0x23C 0x480 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B2_10_GPIO_MUX5_IO11			0x23C 0x480 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_10_LPI2C3_SCL			0x23C 0x480 0x5BC 0x6 0x1
+#define IOMUXC_GPIO_DISP_B2_10_ENET_QOS_RX_ER			0x23C 0x480 0x4FC 0x8 0x2
+#define IOMUXC_GPIO_DISP_B2_10_SPDIF_IN				0x23C 0x480 0x6B4 0x9 0x2
+
+#define IOMUXC_GPIO_DISP_B2_11_VIDEO_MUX_LCDIF_DATA19		0x240 0x484 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_11_EMVSIM2_CLK			0x240 0x484 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B2_11_LPUART2_RXD			0x240 0x484 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_11_WDOG1_RESET_B_DEB		0x240 0x484 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_11_XBAR1_INOUT39			0x240 0x484 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B2_11_GPIO_MUX5_IO12			0x240 0x484 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_11_LPI2C3_SDA			0x240 0x484 0x5C0 0x6 0x1
+#define IOMUXC_GPIO_DISP_B2_11_ENET_QOS_CRS			0x240 0x484 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B2_11_SPDIF_OUT			0x240 0x484 0x0 0x9 0x0
+#define IOMUXC_GPIO_DISP_B2_11_GPIO11_IO12			0x240 0x484 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B2_12_GPIO11_IO13			0x244 0x488 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_12_VIDEO_MUX_LCDIF_DATA20		0x244 0x488 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_12_EMVSIM2_RST			0x244 0x488 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B2_12_FLEXCAN1_TX			0x244 0x488 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_12_LPUART2_CTS_B			0x244 0x488 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_12_XBAR1_INOUT40			0x244 0x488 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B2_12_GPIO_MUX5_IO13			0x244 0x488 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_12_LPI2C4_SCL			0x244 0x488 0x5C4 0x6 0x1
+#define IOMUXC_GPIO_DISP_B2_12_ENET_QOS_COL			0x244 0x488 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B2_12_LPSPI4_SCK			0x244 0x488 0x610 0x9 0x1
+
+#define IOMUXC_GPIO_DISP_B2_13_GPIO11_IO14			0x248 0x48C 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_13_VIDEO_MUX_LCDIF_DATA21		0x248 0x48C 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_13_EMVSIM2_SVEN			0x248 0x48C 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B2_13_FLEXCAN1_RX			0x248 0x48C 0x498 0x2 0x1
+#define IOMUXC_GPIO_DISP_B2_13_LPUART2_RTS_B			0x248 0x48C 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_13_ENET_REF_CLK			0x248 0x48C 0x4A8 0x4 0x2
+#define IOMUXC_GPIO_DISP_B2_13_GPIO_MUX5_IO14			0x248 0x48C 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_13_LPI2C4_SDA			0x248 0x48C 0x5C8 0x6 0x1
+#define IOMUXC_GPIO_DISP_B2_13_ENET_QOS_1588_EVENT0_OUT		0x248 0x48C 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B2_13_LPSPI4_SIN			0x248 0x48C 0x614 0x9 0x1
+
+#define IOMUXC_GPIO_DISP_B2_14_GPIO_MUX5_IO15			0x24C 0x490 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_14_FLEXCAN1_TX			0x24C 0x490 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B2_14_ENET_QOS_1588_EVENT0_IN		0x24C 0x490 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B2_14_LPSPI4_SOUT			0x24C 0x490 0x618 0x9 0x1
+#define IOMUXC_GPIO_DISP_B2_14_GPIO11_IO15			0x24C 0x490 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_14_VIDEO_MUX_LCDIF_DATA22		0x24C 0x490 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_14_EMVSIM2_PD			0x24C 0x490 0x6AC 0x1 0x1
+#define IOMUXC_GPIO_DISP_B2_14_WDOG2_B				0x24C 0x490 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_14_VIDEO_MUX_EXT_DCIC1		0x24C 0x490 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_14_ENET_1G_REF_CLK			0x24C 0x490 0x4C4 0x4 0x3
+
+#define IOMUXC_GPIO_DISP_B2_15_VIDEO_MUX_LCDIF_DATA23		0x250 0x494 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_15_EMVSIM2_POWER_FAIL		0x250 0x494 0x6B0 0x1 0x1
+#define IOMUXC_GPIO_DISP_B2_15_WDOG1_B				0x250 0x494 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_15_VIDEO_MUX_EXT_DCIC2		0x250 0x494 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_15_PIT1_TRIGGER0			0x250 0x494 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B2_15_GPIO_MUX5_IO16			0x250 0x494 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_15_FLEXCAN1_RX			0x250 0x494 0x498 0x6 0x2
+#define IOMUXC_GPIO_DISP_B2_15_ENET_QOS_1588_EVENT0_AUX_IN	0x250 0x494 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B2_15_LPSPI4_PCS0			0x250 0x494 0x60C 0x9 0x1
+#define IOMUXC_GPIO_DISP_B2_15_GPIO11_IO16			0x250 0x494 0x0 0xA 0x0
+
+#endif  /* _DT_BINDINGS_PINCTRL_IMXRT1170_PINFUNC_H */
diff --git a/arch/arm/boot/dts/nxp/imx/mba6ulx.dtsi b/arch/arm/boot/dts/nxp/imx/mba6ulx.dtsi
new file mode 100644
index 000000000000..65fde4f52587
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/mba6ulx.dtsi
@@ -0,0 +1,582 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/ {
+	model = "TQ-Systems MBA6ULx Baseboard";
+
+	aliases {
+		mmc0 = &usdhc2;
+		mmc1 = &usdhc1;
+		rtc0 = &rtc0;
+		rtc1 = &snvs_rtc;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		power-supply = <&reg_mba6ul_3v3>;
+		enable-gpios = <&expander_out0 4 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+
+	beeper: beeper {
+		compatible = "gpio-beeper";
+		gpios = <&expander_out1 6 GPIO_ACTIVE_HIGH>;
+	};
+
+	gpio_buttons: gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_buttons>;
+
+		button-1 {
+			label = "s14";
+			linux,code = <KEY_1>;
+			gpios = <&expander_in0 0 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+
+		button-2 {
+			label = "s6";
+			linux,code = <KEY_2>;
+			gpios = <&expander_in0 1 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+
+		button-3 {
+			label = "s7";
+			linux,code = <KEY_3>;
+			gpios = <&expander_in0 2 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+
+		power-button {
+			label = "POWER";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		status = "okay";
+
+		led1 {
+			label = "led1";
+			gpios = <&expander_out1 4 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led2 {
+			label = "led2";
+			gpios = <&expander_out1 5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	reg_lcd_pwr: regulator-lcd-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-pwr";
+		gpio = <&expander_out0 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		status = "disabled";
+	};
+
+	reg_mba6ul_3v3: regulator-mba6ul-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "supply-mba6ul-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_mba6ul_5v0: regulator-mba6ul-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "supply-mba6ul-5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	reg_mpcie: regulator-mpcie-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "mpcie-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&expander_out0 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+		startup-delay-us = <500000>;
+		vin-supply = <&reg_mba6ul_3v3>;
+	};
+
+	reg_otg2vbus_5v0: regulator-otg2-vbus-5v0 {
+		compatible = "regulator-fixed";
+		gpio = <&expander_out1 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-name = "otg2-vbus-supply-5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_mpcie>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		linux,cma {
+			compatible = "shared-dma-pool";
+			reusable;
+			size = <0x6000000>;
+			linux,cma-default;
+		};
+	};
+
+	sound {
+		compatible = "fsl,imx-audio-tlv320aic32x4";
+		model = "tqm-tlv320aic32";
+		ssi-controller = <&sai1>;
+		audio-codec = <&tlv320aic32x4>;
+		audio-asrc = <&asrc>;
+		audio-routing =
+			"IN3_L", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"IN1_L", "Line In Jack",
+			"IN1_R", "Line In Jack",
+			"Line Out Jack", "LOL",
+			"Line Out Jack", "LOR";
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_mba6ul_3v3>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	xceiver-supply = <&reg_mba6ul_3v3>;
+	status = "okay";
+};
+
+&clks {
+	assigned-clocks = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
+	assigned-clock-rates = <768000000>;
+};
+
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	num-cs = <1>;
+	status = "okay";
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy0>;
+	phy-supply = <&reg_mba6ul_3v3>;
+	phy-reset-gpios = <&expander_out1 1 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <25>;
+	phy-reset-post-delay = <1>;
+	status = "okay";
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2>, <&pinctrl_enet2_mdc>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy1>;
+	phy-supply = <&reg_mba6ul_3v3>;
+	phy-reset-gpios = <&expander_out1 2 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <25>;
+	phy-reset-post-delay = <1>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			reg = <0>;
+			max-speed = <100>;
+		};
+
+		ethphy1: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			clocks = <&clks IMX6UL_CLK_ENET2_REF_125M>;
+			reg = <1>;
+			max-speed = <100>;
+		};
+	};
+};
+
+&i2c4 {
+	tlv320aic32x4: audio-codec@18 {
+		compatible = "ti,tlv320aic32x4";
+		reg = <0x18>;
+		clocks = <&clks IMX6UL_CLK_SAI1>;
+		clock-names = "mclk";
+		ldoin-supply = <&reg_mba6ul_3v3>;
+		iov-supply = <&reg_mba6ul_3v3>;
+	};
+
+	jc42: temperature-sensor@19 {
+		compatible = "nxp,se97b", "jedec,jc-42.4-temp";
+		reg = <0x19>;
+	};
+
+	expander_out0: gpio-expander@20 {
+		compatible = "nxp,pca9554";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		vcc-supply = <&reg_mba6ul_3v3>;
+	};
+
+	expander_in0: gpio-expander@21 {
+		compatible = "nxp,pca9554";
+		reg = <0x21>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_expander_in0>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		vcc-supply = <&reg_mba6ul_3v3>;
+
+		enet1_int-hog {
+			gpio-hog;
+			gpios = <6 0>;
+			input;
+		};
+
+		enet2_int-hog {
+			gpio-hog;
+			gpios = <7 0>;
+			input;
+		};
+	};
+
+	expander_out1: gpio-expander@22 {
+		compatible = "nxp,pca9554";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		vcc-supply = <&reg_mba6ul_3v3>;
+	};
+
+	analog_touch: touchscreen@41 {
+		compatible = "st,stmpe811";
+		reg = <0x41>;
+		interrupts = <21 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-parent = <&gpio4>;
+		status = "disabled";
+
+		touchscreen {
+			compatible = "st,stmpe-ts";
+			st,adc-freq = <1>;      /* 3.25 MHz ADC clock speed */
+			st,ave-ctrl = <3>;      /* 8 sample average control */
+			st,fraction-z = <7>;    /* 7 length fractional part in z */
+			/*
+			 * 50 mA typical 80 mA max touchscreen drivers
+			 * current limit value
+			 */
+			st,i-drive = <1>;
+			st,mod-12b = <1>;       /* 12-bit ADC */
+			st,ref-sel = <0>;       /* internal ADC reference */
+			st,sample-time = <4>;   /* ADC converstion time: 80 clocks */
+			st,settling = <3>;      /* 1 ms panel driver settling time */
+			st,touch-det-delay = <5>; /* 5 ms touch detect interrupt delay */
+		};
+	};
+
+	/* NXP SE97BTP with temperature sensor + eeprom */
+	se97b: eeprom@51 {
+		compatible = "nxp,se97b", "atmel,24c02";
+		reg = <0x51>;
+		pagesize = <16>;
+		vcc-supply = <&reg_mba6ul_3v3>;
+	};
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "okay";
+};
+
+&sai1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai1>;
+	assigned-clocks = <&clks IMX6UL_CLK_SAI1_SEL>,
+			  <&clks IMX6UL_CLK_SAI1>;
+	assigned-clock-parents = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
+	assigned-clock-rates = <0>, <24000000>;
+	fsl,sai-mclk-direction-output;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&uart6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart6>;
+	/* for DTE mode, add below change */
+	/* fsl,dte-mode; */
+	/* pinctrl-0 = <&pinctrl_uart6dte>; */
+	uart-has-rtscts;
+	linux,rs485-enabled-at-boot-time;
+	rs485-rts-active-low;
+	rs485-rx-during-tx;
+	status = "okay";
+};
+
+/* otg-port */
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_otg1>;
+	power-active-high;
+	over-current-active-low;
+	/* we implement only dual role but not a fully featured OTG */
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+	dr_mode = "otg";
+	status = "okay";
+};
+
+/* 7-port usb hub */
+/* id, pwr, oc pins not connected */
+&usbotg2 {
+	disable-over-current;
+	vbus-supply = <&reg_otg2vbus_5v0>;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_mba6ul_3v3>;
+	vqmmc-supply = <&reg_vccsd>;
+	no-1-8-v;
+	no-mmc;
+	no-sdio;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog1>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_buttons: buttonsgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0x100b0
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_TX_DATA__ECSPI2_SCLK	0x1b020
+			MX6UL_PAD_UART5_RX_DATA__ECSPI2_MISO	0x1b020
+			MX6UL_PAD_UART5_TX_DATA__ECSPI2_MOSI	0x1b020
+			MX6UL_PAD_UART4_RX_DATA__ECSPI2_SS0	0x1b020
+		>;
+	};
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1	0x4001b0a8
+		>;
+	};
+
+	pinctrl_enet2: enet2grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00	0x1b0a0
+			MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01	0x1b0a0
+			MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	0x4001b0a8
+		>;
+	};
+
+	pinctrl_enet2_mdc: enet2mdcgrp {
+		fsl,pins = <
+			/* mdio */
+			MX6UL_PAD_GPIO1_IO07__ENET2_MDC		0x1b0b0
+			MX6UL_PAD_GPIO1_IO06__ENET2_MDIO	0x1b0b0
+		>;
+	};
+
+	pinctrl_expander_in0: expanderin0grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA02__GPIO4_IO23	0x1b0b1
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX	0x1b020
+			MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX	0x1b020
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX	0x1b020
+			MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX	0x1b020
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			/* 100 k PD, DSE 120 OHM, SPEED LO */
+			MX6UL_PAD_GPIO1_IO09__PWM2_OUT		0x00003050
+		>;
+	};
+
+	pinctrl_sai1: sai1grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA05__SAI1_TX_BCLK	0x1b0b1
+			MX6UL_PAD_CSI_DATA04__SAI1_TX_SYNC	0x1b0b1
+			MX6UL_PAD_CSI_DATA07__SAI1_TX_DATA	0x1f0b8
+			MX6UL_PAD_CSI_DATA06__SAI1_RX_DATA	0x110b0
+			MX6UL_PAD_CSI_DATA01__SAI1_MCLK		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart6: uart6grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_MCLK__UART6_DCE_TX	0x1b0b1
+			MX6UL_PAD_CSI_PIXCLK__UART6_DCE_RX	0x1b0b1
+			MX6UL_PAD_CSI_VSYNC__UART6_DCE_RTS	0x1b0b1
+			MX6UL_PAD_CSI_HSYNC__UART6_DCE_CTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart6dte: uart6dtegrp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_PIXCLK__UART6_DTE_TX	0x1b0b1
+			MX6UL_PAD_CSI_MCLK__UART6_DTE_RX	0x1b0b1
+			MX6UL_PAD_CSI_HSYNC__UART6_DTE_RTS	0x1b0b1
+			MX6UL_PAD_CSI_VSYNC__UART6_DTE_CTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_usb_otg1: usbotg1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID	0x00017059
+			MX6UL_PAD_GPIO1_IO01__USB_OTG1_OC	0x0001b0b0
+			MX6UL_PAD_GPIO1_IO04__USB_OTG1_PWR	0x0001b099
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x00017069
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x00017059
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x00017059
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x00017059
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x00017059
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x00017059
+			/* WP */
+			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18	0x0001b099
+			/* CD */
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x0001b099
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x00017069
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x000170b9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x000170b9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x000170b9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x000170b9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x000170b9
+			/* WP */
+			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18	0x0001b099
+			/* CD */
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x0001b099
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x00017069
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x000170f9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x000170f9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x000170f9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x000170f9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x000170f9
+			/* WP */
+			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18	0x0001b099
+			/* CD */
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x0001b099
+		>;
+	};
+
+	pinctrl_wdog1: wdog1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO08__WDOG1_WDOG_B	0x0001b099
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/lpc/Makefile b/arch/arm/boot/dts/nxp/lpc/Makefile
new file mode 100644
index 000000000000..56b9a0ebb917
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/lpc/Makefile
@@ -0,0 +1,9 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_LPC18XX) += \
+	lpc4337-ciaa.dtb \
+	lpc4350-hitex-eval.dtb \
+	lpc4357-ea4357-devkit.dtb \
+	lpc4357-myd-lpc4357.dtb
+dtb-$(CONFIG_ARCH_LPC32XX) += \
+	lpc3250-ea3250.dtb \
+	lpc3250-phy3250.dtb
diff --git a/arch/arm/boot/dts/lpc18xx.dtsi b/arch/arm/boot/dts/nxp/lpc/lpc18xx.dtsi
index 10b8249b8ab6..152e98cf0c4e 100644
--- a/arch/arm/boot/dts/lpc18xx.dtsi
+++ b/arch/arm/boot/dts/nxp/lpc/lpc18xx.dtsi
@@ -11,7 +11,7 @@
  *
  */
 
-#include "armv7-m.dtsi"
+#include "../../armv7-m.dtsi"
 
 #include "dt-bindings/clock/lpc18xx-cgu.h"
 #include "dt-bindings/clock/lpc18xx-ccu.h"
@@ -74,7 +74,7 @@
 		sct_pwm: pwm@40000000 {
 			compatible = "nxp,lpc1850-sct-pwm";
 			reg = <0x40000000 0x1000>;
-			clocks =<&ccu1 CLK_CPU_SCT>;
+			clocks = <&ccu1 CLK_CPU_SCT>;
 			clock-names = "pwm";
 			resets = <&rgu 37>;
 			#pwm-cells = <3>;
@@ -100,28 +100,30 @@
 			memcpy-bus-width = <32>;
 		};
 
-		spifi: flash-controller@40003000 {
+		spifi: spi@40003000 {
 			compatible = "nxp,lpc1773-spifi";
 			reg = <0x40003000 0x1000>, <0x14000000 0x4000000>;
 			reg-names = "spifi", "flash";
 			interrupts = <30>;
 			clocks = <&ccu1 CLK_SPIFI>, <&ccu1 CLK_CPU_SPIFI>;
 			clock-names = "spifi", "reg";
+			#address-cells = <1>;
+			#size-cells = <0>;
 			resets = <&rgu 53>;
 			status = "disabled";
 		};
 
-		mmcsd: mmcsd@40004000 {
+		mmcsd: mmc@40004000 {
 			compatible = "snps,dw-mshc";
 			reg = <0x40004000 0x1000>;
 			interrupts = <6>;
-			clocks = <&ccu2 CLK_SDIO>, <&ccu1 CLK_CPU_SDIO>;
-			clock-names = "ciu", "biu";
+			clocks = <&ccu1 CLK_CPU_SDIO>, <&ccu2 CLK_SDIO>;
+			clock-names = "biu", "ciu";
 			resets = <&rgu 20>;
 			status = "disabled";
 		};
 
-		usb0: ehci@40006100 {
+		usb0: usb@40006100 {
 			compatible = "nxp,lpc1850-ehci", "generic-ehci";
 			reg = <0x40006100 0x100>;
 			interrupts = <8>;
@@ -133,7 +135,7 @@
 			status = "disabled";
 		};
 
-		usb1: ehci@40007100 {
+		usb1: usb@40007100 {
 			compatible = "nxp,lpc1850-ehci", "generic-ehci";
 			reg = <0x40007100 0x100>;
 			interrupts = <9>;
@@ -183,7 +185,7 @@
 			compatible = "nxp,lpc1850-dwmac", "snps,dwmac-3.611", "snps,dwmac";
 			reg = <0x40010000 0x2000>;
 			interrupts = <5>;
-			interrupt-names	= "macirq";
+			interrupt-names = "macirq";
 			clocks = <&ccu1 CLK_CPU_ETHERNET>;
 			clock-names = "stmmaceth";
 			resets = <&rgu 22>;
@@ -535,3 +537,7 @@
 		};
 	};
 };
+
+&nvic {
+	arm,num-irq-priority-bits = <3>;
+};
diff --git a/arch/arm/boot/dts/lpc3250-ea3250.dts b/arch/arm/boot/dts/nxp/lpc/lpc3250-ea3250.dts
index 63c6f17bb7c9..63c6f17bb7c9 100644
--- a/arch/arm/boot/dts/lpc3250-ea3250.dts
+++ b/arch/arm/boot/dts/nxp/lpc/lpc3250-ea3250.dts
diff --git a/arch/arm/boot/dts/lpc3250-phy3250.dts b/arch/arm/boot/dts/nxp/lpc/lpc3250-phy3250.dts
index 21a6d0bca1e8..21a6d0bca1e8 100644
--- a/arch/arm/boot/dts/lpc3250-phy3250.dts
+++ b/arch/arm/boot/dts/nxp/lpc/lpc3250-phy3250.dts
diff --git a/arch/arm/boot/dts/lpc32xx.dtsi b/arch/arm/boot/dts/nxp/lpc/lpc32xx.dtsi
index c87066d6c995..2236901a0031 100644
--- a/arch/arm/boot/dts/lpc32xx.dtsi
+++ b/arch/arm/boot/dts/nxp/lpc/lpc32xx.dtsi
@@ -77,12 +77,13 @@
 			status = "disabled";
 		};
 
-		dma: dma@31000000 {
+		dma: dma-controller@31000000 {
 			compatible = "arm,pl080", "arm,primecell";
 			reg = <0x31000000 0x1000>;
 			interrupts = <28 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clk LPC32XX_CLK_DMA>;
 			clock-names = "apb_pclk";
+			#dma-cells = <2>;
 		};
 
 		usb {
@@ -94,7 +95,7 @@
 			/*
 			 * Enable either ohci or usbd (gadget)!
 			 */
-			ohci: ohci@0 {
+			ohci: usb@0 {
 				compatible = "nxp,ohci-nxp", "usb-ohci";
 				reg = <0x0 0x300>;
 				interrupt-parent = <&sic1>;
@@ -224,8 +225,8 @@
 				status = "disabled";
 			};
 
-			sd: sd@20098000 {
-				compatible = "arm,pl18x", "arm,primecell";
+			sd: mmc@20098000 {
+				compatible = "arm,pl180", "arm,primecell";
 				reg = <0x20098000 0x1000>;
 				interrupts = <15 IRQ_TYPE_LEVEL_HIGH>,
 					     <13 IRQ_TYPE_LEVEL_HIGH>;
@@ -298,11 +299,11 @@
 				clocks = <&clk LPC32XX_CLK_I2C2>;
 			};
 
-			mpwm: mpwm@400e8000 {
+			mpwm: pwm@400e8000 {
 				compatible = "nxp,lpc3220-motor-pwm";
 				reg = <0x400e8000 0x78>;
+				#pwm-cells = <3>;
 				status = "disabled";
-				#pwm-cells = <2>;
 			};
 		};
 
@@ -315,7 +316,7 @@
 			/* System Control Block */
 			scb {
 				compatible = "simple-bus";
-				ranges = <0x0 0x040004000 0x00001000>;
+				ranges = <0x0 0x40004000 0x00001000>;
 				#address-cells = <1>;
 				#size-cells = <1>;
 
@@ -481,6 +482,7 @@
 				compatible = "nxp,lpc3220-pwm";
 				reg = <0x4005c000 0x4>;
 				clocks = <&clk LPC32XX_CLK_PWM1>;
+				#pwm-cells = <3>;
 				assigned-clocks = <&clk LPC32XX_CLK_PWM1>;
 				assigned-clock-parents = <&clk LPC32XX_CLK_PERIPH>;
 				status = "disabled";
@@ -490,6 +492,7 @@
 				compatible = "nxp,lpc3220-pwm";
 				reg = <0x4005c004 0x4>;
 				clocks = <&clk LPC32XX_CLK_PWM2>;
+				#pwm-cells = <3>;
 				assigned-clocks = <&clk LPC32XX_CLK_PWM2>;
 				assigned-clock-parents = <&clk LPC32XX_CLK_PERIPH>;
 				status = "disabled";
diff --git a/arch/arm/boot/dts/lpc4337-ciaa.dts b/arch/arm/boot/dts/nxp/lpc/lpc4337-ciaa.dts
index beddaba85393..5ff43c825944 100644
--- a/arch/arm/boot/dts/lpc4337-ciaa.dts
+++ b/arch/arm/boot/dts/nxp/lpc/lpc4337-ciaa.dts
@@ -108,14 +108,14 @@
 	};
 
 	ssp_pins: ssp-pins {
-		ssp1_cs {
+		ssp1_cs_cfg {
 			pins = "p6_7";
 			function = "gpio";
 			bias-pull-up;
 			bias-disable;
 		};
 
-		ssp1_miso_mosi {
+		ssp1_miso_mosi_cfg {
 			pins = "p1_3", "p1_4";
 			function = "ssp1";
 			slew-rate = <1>;
@@ -124,7 +124,7 @@
 			input-schmitt-disable;
 		};
 
-		ssp1_sck {
+		ssp1_sck_cfg {
 			pins = "pf_4";
 			function = "ssp1";
 			slew-rate = <1>;
diff --git a/arch/arm/boot/dts/lpc4350-hitex-eval.dts b/arch/arm/boot/dts/nxp/lpc/lpc4350-hitex-eval.dts
index 93d0c2e99e7c..18f757c56905 100644
--- a/arch/arm/boot/dts/lpc4350-hitex-eval.dts
+++ b/arch/arm/boot/dts/nxp/lpc/lpc4350-hitex-eval.dts
@@ -43,50 +43,50 @@
 		poll-interval = <100>;
 		autorepeat;
 
-		button0 {
+		button-0 {
 			label = "joy:right";
 			linux,code = <KEY_RIGHT>;
 			gpios = <&pca_gpio 8 GPIO_ACTIVE_LOW>;
 		};
 
-		button1 {
+		button-1 {
 			label = "joy:up";
 			linux,code = <KEY_UP>;
 			gpios = <&pca_gpio 9 GPIO_ACTIVE_LOW>;
 		};
 
 
-		button2 {
+		button-2 {
 			label = "joy:enter";
 			linux,code = <KEY_ENTER>;
 			gpios = <&pca_gpio 10 GPIO_ACTIVE_LOW>;
 		};
 
-		button3 {
+		button-3 {
 			label = "joy:left";
 			linux,code = <KEY_LEFT>;
 			gpios = <&pca_gpio 11 GPIO_ACTIVE_LOW>;
 		};
 
-		button4 {
+		button-4 {
 			label = "joy:down";
 			linux,code = <KEY_DOWN>;
 			gpios = <&pca_gpio 12 GPIO_ACTIVE_LOW>;
 		};
 
-		button5 {
+		button-5 {
 			label = "user:sw3";
 			linux,code = <KEY_F1>;
 			gpios = <&pca_gpio 13 GPIO_ACTIVE_LOW>;
 		};
 
-		button6 {
+		button-6 {
 			label = "user:sw4";
 			linux,code = <KEY_F2>;
 			gpios = <&pca_gpio 14 GPIO_ACTIVE_LOW>;
 		};
 
-		button7 {
+		button-7 {
 			label = "user:sw5";
 			linux,code = <KEY_F3>;
 			gpios = <&pca_gpio 15 GPIO_ACTIVE_LOW>;
@@ -406,6 +406,9 @@
 		ext_sram: sram@2,0 {
 			compatible = "mmio-sram";
 			reg = <2 0 0x80000>; /* 512 KiB SRAM on IS62WV25616 */
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 2 0 0x80000>;
 		};
 	};
 };
@@ -451,8 +454,9 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&spifi_pins>;
 
-	flash {
+	flash@0 {
 		compatible = "jedec,spi-nor";
+		reg = <0>;
 		spi-rx-bus-width = <4>;
 		#address-cells = <1>;
 		#size-cells = <1>;
diff --git a/arch/arm/boot/dts/lpc4350.dtsi b/arch/arm/boot/dts/nxp/lpc/lpc4350.dtsi
index c4422f587055..707d22a219d8 100644
--- a/arch/arm/boot/dts/lpc4350.dtsi
+++ b/arch/arm/boot/dts/nxp/lpc/lpc4350.dtsi
@@ -24,16 +24,25 @@
 		sram0: sram@10000000 {
 			compatible = "mmio-sram";
 			reg = <0x10000000 0x20000>; /* 96 + 32 KiB local SRAM */
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
 		};
 
 		sram1: sram@10080000 {
 			compatible = "mmio-sram";
 			reg = <0x10080000 0x12000>; /* 64 + 8 KiB local SRAM */
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
 		};
 
 		sram2: sram@20000000 {
 			compatible = "mmio-sram";
 			reg = <0x20000000 0x10000>; /* 4 x 16 KiB AHB SRAM */
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/lpc4357-ea4357-devkit.dts b/arch/arm/boot/dts/nxp/lpc/lpc4357-ea4357-devkit.dts
index 224f80a4a31d..7ccb4c2ca571 100644
--- a/arch/arm/boot/dts/lpc4357-ea4357-devkit.dts
+++ b/arch/arm/boot/dts/nxp/lpc/lpc4357-ea4357-devkit.dts
@@ -60,31 +60,31 @@
 		poll-interval = <100>;
 		autorepeat;
 
-		button0 {
+		button-0 {
 			label = "joy_enter";
 			linux,code = <KEY_ENTER>;
 			gpios = <&gpio LPC_GPIO(4,8) GPIO_ACTIVE_LOW>;
 		};
 
-		button1 {
+		button-1 {
 			label = "joy_left";
 			linux,code = <KEY_LEFT>;
 			gpios = <&gpio LPC_GPIO(4,9) GPIO_ACTIVE_LOW>;
 		};
 
-		button2 {
+		button-2 {
 			label = "joy_up";
 			linux,code = <KEY_UP>;
 			gpios = <&gpio LPC_GPIO(4,10) GPIO_ACTIVE_LOW>;
 		};
 
-		button3 {
+		button-3 {
 			label = "joy_right";
 			linux,code = <KEY_RIGHT>;
 			gpios = <&gpio LPC_GPIO(4,12) GPIO_ACTIVE_LOW>;
 		};
 
-		button4 {
+		button-4 {
 			label = "joy_down";
 			linux,code = <KEY_DOWN>;
 			gpios = <&gpio LPC_GPIO(4,13) GPIO_ACTIVE_LOW>;
@@ -403,7 +403,7 @@
 	};
 
 	ssp0_pins: ssp0-pins {
-		ssp0_sck_miso_mosi {
+		ssp0_sck_miso_mosi_cfg {
 			pins = "pf_0", "pf_2", "pf_3";
 			function = "ssp0";
 			slew-rate = <1>;
@@ -412,7 +412,7 @@
 			input-schmitt-disable;
 		};
 
-		ssp0_ssel {
+		ssp0_ssel_cfg {
 			pins = "pf_1";
 			function = "ssp0";
 			bias-pull-up;
@@ -452,12 +452,12 @@
 	};
 
 	usb0_pins: usb0-pins {
-		usb0_pwr_enable {
+		usb0_pwr_enable_cfg {
 			pins = "p2_3";
 			function = "usb0";
 		};
 
-		usb0_pwr_fault {
+		usb0_pwr_fault_cfg {
 			pins = "p8_0";
 			function = "usb0";
 			bias-disable;
@@ -482,8 +482,8 @@
 		reg = <0x1d>;
 	};
 
-	lm75@48 {
-		compatible = "nxp,lm75";
+	temperature-sensor@48 {
+		compatible = "national,lm75b";
 		reg = <0x48>;
 	};
 
@@ -582,8 +582,9 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&spifi_pins>;
 
-	flash {
+	flash@0 {
 		compatible = "jedec,spi-nor";
+		reg = <0>;
 		spi-cpol;
 		spi-cpha;
 		spi-rx-bus-width = <4>;
diff --git a/arch/arm/boot/dts/lpc4357-myd-lpc4357.dts b/arch/arm/boot/dts/nxp/lpc/lpc4357-myd-lpc4357.dts
index 1f84654df50c..d18f2b2caf68 100644
--- a/arch/arm/boot/dts/lpc4357-myd-lpc4357.dts
+++ b/arch/arm/boot/dts/nxp/lpc/lpc4357-myd-lpc4357.dts
@@ -63,6 +63,7 @@
 
 	panel: panel {
 		compatible = "innolux,at070tn92";
+		power-supply = <&vcc>;
 
 		port {
 			panel_input: endpoint {
@@ -511,7 +512,7 @@
 	clock-frequency = <400000>;
 
 	sensor@49 {
-		compatible = "lm75";
+		compatible = "national,lm75";
 		reg = <0x49>;
 	};
 
@@ -543,7 +544,7 @@
 	pinctrl-0 = <&enet_rmii_pins>;
 	phy-handle = <&phy1>;
 
-	mdio0 {
+	mdio {
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "snps,dwmac-mdio";
@@ -569,8 +570,9 @@
 	pinctrl-0 = <&spifi_pins>;
 
 	/* Atmel AT25DF321A */
-	flash {
+	flash@0 {
 		compatible = "jedec,spi-nor";
+		reg = <0>;
 		spi-max-frequency = <51000000>;
 		spi-cpol;
 		spi-cpha;
diff --git a/arch/arm/boot/dts/lpc4357.dtsi b/arch/arm/boot/dts/nxp/lpc/lpc4357.dtsi
index 72f12db8d53a..d138ee7869ff 100644
--- a/arch/arm/boot/dts/lpc4357.dtsi
+++ b/arch/arm/boot/dts/nxp/lpc/lpc4357.dtsi
@@ -24,16 +24,25 @@
 		sram0: sram@10000000 {
 			compatible = "mmio-sram";
 			reg = <0x10000000 0x8000>; /* 32 KiB local SRAM */
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
 		};
 
 		sram1: sram@10080000 {
 			compatible = "mmio-sram";
 			reg = <0x10080000 0xa000>; /* 32 + 8 KiB local SRAM */
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
 		};
 
 		sram2: sram@20000000 {
 			compatible = "mmio-sram";
 			reg = <0x20000000 0x10000>; /* 4 x 16 KiB AHB SRAM */
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/nxp/ls/Makefile b/arch/arm/boot/dts/nxp/ls/Makefile
new file mode 100644
index 000000000000..53240b04c968
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/ls/Makefile
@@ -0,0 +1,17 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_SOC_LS1021A) += \
+	ls1021a-iot.dtb \
+	ls1021a-moxa-uc-8410a.dtb \
+	ls1021a-qds.dtb \
+	ls1021a-tqmls1021a-mbls1021a.dtb \
+	ls1021a-tsn.dtb \
+	ls1021a-twr.dtb
+
+ls1021a-tqmls1021a-mbls1021a-hdmi-dtbs += ls1021a-tqmls1021a-mbls1021a.dtb ls1021a-tqmls1021a-mbls1021a-hdmi.dtbo
+ls1021a-tqmls1021a-mbls1021a-lvds-tm070jvhg33-dtbs += ls1021a-tqmls1021a-mbls1021a.dtb ls1021a-tqmls1021a-mbls1021a-lvds-tm070jvhg33.dtbo
+ls1021a-tqmls1021a-mbls1021a-rgb-cdtech-dc44-dtbs += ls1021a-tqmls1021a-mbls1021a.dtb ls1021a-tqmls1021a-mbls1021a-rgb-cdtech-dc44.dtbo
+ls1021a-tqmls1021a-mbls1021a-rgb-cdtech-fc21-dtbs += ls1021a-tqmls1021a-mbls1021a.dtb ls1021a-tqmls1021a-mbls1021a-rgb-cdtech-fc21.dtbo
+dtb-$(CONFIG_SOC_LS1021A) += ls1021a-tqmls1021a-mbls1021a-hdmi.dtb
+dtb-$(CONFIG_SOC_LS1021A) += ls1021a-tqmls1021a-mbls1021a-lvds-tm070jvhg33.dtb
+dtb-$(CONFIG_SOC_LS1021A) += ls1021a-tqmls1021a-mbls1021a-rgb-cdtech-dc44.dtb
+dtb-$(CONFIG_SOC_LS1021A) += ls1021a-tqmls1021a-mbls1021a-rgb-cdtech-fc21.dtb
diff --git a/arch/arm/boot/dts/nxp/ls/ls1021a-iot.dts b/arch/arm/boot/dts/nxp/ls/ls1021a-iot.dts
new file mode 100644
index 000000000000..e13ccae629a7
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/ls/ls1021a-iot.dts
@@ -0,0 +1,227 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2021-2022 NXP
+ *
+ */
+
+/dts-v1/;
+#include "ls1021a.dtsi"
+
+/ {
+	model = "LS1021A-IOT Board";
+	compatible = "fsl,ls1021a-iot", "fsl,ls1021a";
+
+	sys_mclk: clock-mclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24576000>;
+	};
+
+	reg_3p3v: regulator-3V3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_2p5v: regulator-2V5 {
+		compatible = "regulator-fixed";
+		regulator-name = "2P5V";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,widgets =
+			"Microphone", "Microphone Jack",
+			"Headphone", "Headphone Jack",
+			"Speaker", "Speaker Ext",
+			"Line", "Line In Jack";
+		simple-audio-card,routing =
+			"MIC_IN", "Microphone Jack",
+			"Microphone Jack", "Mic Bias",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT",
+			"Speaker Ext", "LINE_OUT";
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai2>;
+			frame-master;
+			bitclock-master;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&sgtl5000>;
+			frame-master;
+			bitclock-master;
+		};
+	};
+};
+
+&can0 {
+	status = "disabled";
+};
+
+&can1 {
+	status = "disabled";
+};
+
+&can2 {
+	status = "disabled";
+};
+
+&can3 {
+	status = "okay";
+};
+
+&dcu {
+	display = <&display>;
+	status = "okay";
+
+	display: display@0 {
+		bits-per-pixel = <24>;
+
+		display-timings {
+			native-mode = <&timing0>;
+
+			timing0: mode0 {
+				clock-frequency = <25000000>;
+				hactive = <640>;
+				vactive = <480>;
+				hback-porch = <80>;
+				hfront-porch = <80>;
+				vback-porch = <16>;
+				vfront-porch = <16>;
+				hsync-len = <12>;
+				vsync-len = <2>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+			};
+		};
+	};
+};
+
+&enet0 {
+	tbi-handle = <&tbi1>;
+	phy-handle = <&phy1>;
+	phy-connection-type = "sgmii";
+	status = "okay";
+};
+
+&enet1 {
+	tbi-handle = <&tbi1>;
+	phy-handle = <&phy3>;
+	phy-connection-type = "sgmii";
+	status = "okay";
+};
+
+&enet2 {
+	fixed-link = <0 1 1000 0 0>;
+	phy-connection-type = "rgmii-id";
+	status = "okay";
+};
+
+&esdhc {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	pca9555: gpio@23 {
+		compatible = "nxp,pca9555";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	sgtl5000: audio-codec@2a {
+		#sound-dai-cells = <0x0>;
+		compatible = "fsl,sgtl5000";
+		reg = <0x2a>;
+		VDDA-supply = <&reg_3p3v>;
+		VDDIO-supply = <&reg_2p5v>;
+		clocks = <&sys_mclk>;
+	};
+
+	max1239: adc@35 {
+		compatible = "maxim,max1239";
+		reg = <0x35>;
+		#io-channel-cells = <1>;
+	};
+
+	ina2201: core-monitor@44 {
+		compatible = "ti,ina220";
+		reg = <0x44>;
+		shunt-resistor = <1000>;
+	};
+
+	ina2202: current-monitor@45 {
+		compatible = "ti,ina220";
+		reg = <0x45>;
+		shunt-resistor = <1000>;
+	};
+
+	lm75b: thermal-monitor@48 {
+		compatible = "national,lm75b";
+		reg = <0x48>;
+	};
+};
+
+&lpuart0 {
+	status = "okay";
+};
+
+&mdio0 {
+	phy0: ethernet-phy@0 {
+		reg = <0x0>;
+	};
+
+	phy1: ethernet-phy@1 {
+		reg = <0x1>;
+	};
+
+	phy2: ethernet-phy@2 {
+		reg = <0x2>;
+	};
+
+	phy3: ethernet-phy@3 {
+		reg = <0x3>;
+	};
+
+	tbi1: tbi-phy@1f {
+		reg = <0x1f>;
+		device_type = "tbi-phy";
+	};
+};
+
+&qspi {
+	num-cs = <2>;
+	status = "okay";
+
+	s25fl128s: flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+	};
+};
+
+&sai2 {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/ls1021a-moxa-uc-8410a.dts b/arch/arm/boot/dts/nxp/ls/ls1021a-moxa-uc-8410a.dts
index f3ddea934f1b..d2cae8c7d7a6 100644
--- a/arch/arm/boot/dts/ls1021a-moxa-uc-8410a.dts
+++ b/arch/arm/boot/dts/nxp/ls/ls1021a-moxa-uc-8410a.dts
@@ -30,11 +30,11 @@
 	};
 
 	reg_3p3v: regulator-3p3v {
-		  compatible = "regulator-fixed";
-		  regulator-name = "3P3V";
-		  regulator-min-microvolt = <3300000>;
-		  regulator-max-microvolt = <3300000>;
-		  regulator-always-on;
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
 	};
 
 	leds {
diff --git a/arch/arm/boot/dts/ls1021a-qds.dts b/arch/arm/boot/dts/nxp/ls/ls1021a-qds.dts
index f1acb97aee69..a880875ced83 100644
--- a/arch/arm/boot/dts/ls1021a-qds.dts
+++ b/arch/arm/boot/dts/nxp/ls/ls1021a-qds.dts
@@ -66,7 +66,7 @@
 	bus-num = <0>;
 	status = "okay";
 
-	dspiflash: at45db021d@0 {
+	dspiflash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "atmel,at45db021d", "atmel,at45", "atmel,dataflash";
@@ -187,7 +187,7 @@
 		 <0x3 0x0 0x0 0x7fb00000 0x00000100>;
 	status = "okay";
 
-	nor@0,0 {
+	flash@0,0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "cfi-flash";
@@ -211,8 +211,8 @@
 		device-width = <1>;
 		ranges = <0 3 0 0x100>;
 
-		mdio-mux-emi1 {
-			compatible = "mdio-mux-mmioreg";
+		mdio-mux@54 {
+			compatible = "mdio-mux-mmioreg", "mdio-mux";
 			mdio-parent-bus = <&mdio0>;
 			#address-cells = <1>;
 			#size-cells = <0>;
diff --git a/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a-mbls1021a-hdmi.dtso b/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a-mbls1021a-hdmi.dtso
new file mode 100644
index 000000000000..e713a2ecbfc2
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a-mbls1021a-hdmi.dtso
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2013-2014 Freescale Semiconductor, Inc.
+ * Copyright 2018-2025 TQ-Systems GmbH <linux@ew.tq-group.com>,
+ * D-82229 Seefeld, Germany.
+ * Author: Alexander Stein
+ */
+
+/dts-v1/;
+/plugin/;
+
+&dcu {
+	status = "okay";
+
+	port {
+		dcu_out: endpoint {
+			remote-endpoint = <&sii9022a_in>;
+		};
+	};
+};
+
+&hdmi_out {
+	status = "okay";
+};
+
+&sii9022a {
+	status = "okay";
+};
+
+&sii9022a_in {
+	remote-endpoint = <&dcu_out>;
+};
diff --git a/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a-mbls1021a-lvds-tm070jvhg33.dtso b/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a-mbls1021a-lvds-tm070jvhg33.dtso
new file mode 100644
index 000000000000..e9708f3c6740
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a-mbls1021a-lvds-tm070jvhg33.dtso
@@ -0,0 +1,47 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2013-2014 Freescale Semiconductor, Inc.
+ * Copyright 2018-2025 TQ-Systems GmbH <linux@ew.tq-group.com>,
+ * D-82229 Seefeld, Germany.
+ * Author: Alexander Stein
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/dts-v1/;
+/plugin/;
+
+&backlight_dcu {
+	status = "okay";
+};
+
+&dcu {
+	status = "okay";
+
+	port {
+		dcu_out: endpoint {
+			remote-endpoint = <&lvds_encoder_in>;
+		};
+	};
+};
+
+&display {
+	compatible = "tianma,tm070jvhg33";
+	status = "okay";
+};
+
+&lvds_encoder {
+	status = "okay";
+};
+
+&lvds_encoder_in {
+	remote-endpoint = <&dcu_out>;
+};
+
+&lvds_encoder_out {
+	remote-endpoint = <&panel_in>;
+};
+
+&panel_in {
+	remote-endpoint = <&lvds_encoder_out>;
+};
diff --git a/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a-mbls1021a-rgb-cdtech-dc44.dtso b/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a-mbls1021a-rgb-cdtech-dc44.dtso
new file mode 100644
index 000000000000..66cedc2dcd96
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a-mbls1021a-rgb-cdtech-dc44.dtso
@@ -0,0 +1,55 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2013-2014 Freescale Semiconductor, Inc.
+ * Copyright 2018-2025 TQ-Systems GmbH <linux@ew.tq-group.com>,
+ * D-82229 Seefeld, Germany.
+ * Author: Alexander Stein
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/dts-v1/;
+/plugin/;
+
+&backlight_dcu {
+	status = "okay";
+};
+
+&dcu {
+	status = "okay";
+
+	port {
+		dcu_out: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
+};
+
+&display {
+	compatible = "cdtech,s070swv29hg-dc44";
+	status = "okay";
+};
+
+&i2c0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	polytouch: touchscreen@38 {
+		compatible = "edt,edt-ft5406";
+		reg = <0x38>;
+		interrupt-parent = <&pca9554_0>;
+		interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+		/* LCD_PWR_EN -> TSC_WAKE */
+		wake-gpios = <&pca9554_1 4 GPIO_ACTIVE_HIGH>;
+		iovcc-supply = <&reg_3p3v>;
+		vcc-supply = <&reg_3p3v>;
+		gain = <20>;
+		touchscreen-size-x = <800>;
+		touchscreen-size-y = <480>;
+	};
+};
+
+&panel_in {
+	remote-endpoint = <&dcu_out>;
+};
diff --git a/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a-mbls1021a-rgb-cdtech-fc21.dtso b/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a-mbls1021a-rgb-cdtech-fc21.dtso
new file mode 100644
index 000000000000..8b9455bffbd2
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a-mbls1021a-rgb-cdtech-fc21.dtso
@@ -0,0 +1,55 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2013-2014 Freescale Semiconductor, Inc.
+ * Copyright 2018-2025 TQ-Systems GmbH <linux@ew.tq-group.com>,
+ * D-82229 Seefeld, Germany.
+ * Author: Alexander Stein
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/dts-v1/;
+/plugin/;
+
+&backlight_dcu {
+	status = "okay";
+};
+
+&dcu {
+	status = "okay";
+
+	port {
+		dcu_out: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
+};
+
+&display {
+	compatible = "cdtech,s070pws19hp-fc21";
+	status = "okay";
+};
+
+&i2c0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	polytouch: touchscreen@38 {
+		compatible = "edt,edt-ft5406";
+		reg = <0x38>;
+		interrupt-parent = <&pca9554_0>;
+		interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+		/* LCD_PWR_EN -> TSC_WAKE */
+		wake-gpios = <&pca9554_1 4 GPIO_ACTIVE_HIGH>;
+		iovcc-supply = <&reg_3p3v>;
+		vcc-supply = <&reg_3p3v>;
+		gain = <20>;
+		touchscreen-size-x = <800>;
+		touchscreen-size-y = <480>;
+	};
+};
+
+&panel_in {
+	remote-endpoint = <&dcu_out>;
+};
diff --git a/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a-mbls1021a.dts b/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a-mbls1021a.dts
new file mode 100644
index 000000000000..5606585dd560
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a-mbls1021a.dts
@@ -0,0 +1,406 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2013-2014 Freescale Semiconductor, Inc.
+ * Copyright 2018-2023 TQ-Systems GmbH <linux@ew.tq-group.com>,
+ * D-82229 Seefeld, Germany.
+ * Author: Alexander Stein
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/leds/leds-pca9532.h>
+#include <dt-bindings/net/ti-dp83867.h>
+
+#include "ls1021a-tqmls1021a.dtsi"
+
+/ {
+	model = "TQMLS102xA SOM on MBLS102xA";
+	compatible = "tq,ls1021a-tqmls1021a-mbls102xa", "tq,ls1021a-tqmls1021a", "fsl,ls1021a";
+
+	audio_mclk: audio-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	backlight_dcu: backlight {
+		compatible = "gpio-backlight";
+		gpios = <&pca9530 0 GPIO_ACTIVE_LOW>;
+		status = "disabled";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		switch-1 {
+			label = "S6";
+			linux,code = <BTN_0>;
+			gpios = <&pca9554_0 0 GPIO_ACTIVE_LOW>;
+		};
+
+		btn2: switch-2 {
+			label = "S7";
+			linux,code = <BTN_1>;
+			gpios = <&pca9554_0 1 GPIO_ACTIVE_LOW>;
+		};
+
+		switch-3 {
+			label = "S8";
+			linux,code = <BTN_2>;
+			gpios = <&pca9554_0 2 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio_leds: gpio-leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+			function-enumerator = <0>;
+			gpios = <&pca9554_2 4 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-1 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+			function-enumerator = <1>;
+			gpios = <&pca9554_2 5 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-2 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+			function-enumerator = <2>;
+			gpios = <&pca9554_2 6 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-3 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_HEARTBEAT;
+			function-enumerator = <0>;
+			gpios = <&pca9554_2 7 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	lvds_encoder: lvds-encoder {
+		compatible = "ti,sn75lvds83", "lvds-encoder";
+		power-supply = <&reg_3p3v>;
+		status = "disabled";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lvds_encoder_in: endpoint {};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				lvds_encoder_out: endpoint {};
+			};
+		};
+	};
+
+	reg_1p2v: regulator-1p2v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P2V";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-always-on;
+		vin-supply = <&reg_3p3v>;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	hdmi_out: hdmi {
+		compatible = "hdmi-connector";
+		type = "a";
+		ddc-i2c-bus = <&i2c0>;
+		status = "disabled";
+
+		port {
+			hdmi_in: endpoint {
+				remote-endpoint = <&sii9022a_out>;
+			};
+		};
+	};
+
+	display: panel {
+		backlight = <&backlight_dcu>;
+		enable-gpios = <&pca9554_1 3 GPIO_ACTIVE_HIGH>;
+		power-supply = <&reg_3p3v>;
+		status = "disabled";
+
+		port {
+			panel_in: endpoint {};
+		};
+	};
+
+	sound {
+		compatible = "fsl,imx-audio-tlv320aic32x4";
+		model = "tqm-tlv320aic32";
+		ssi-controller = <&sai1>;
+		audio-codec = <&tlv320aic32x4>;
+	};
+
+};
+
+&can0 {
+	xceiver-supply = <&reg_3p3v>;
+	status = "okay";
+};
+
+&can1 {
+	xceiver-supply = <&reg_3p3v>;
+	status = "okay";
+};
+
+&dspi0 {
+	status = "okay";
+};
+
+&enet0 {
+	phy-handle = <&rgmii_phy0c>;
+	phy-mode = "rgmii-id";
+	mac-address = [ 00 00 00 00 00 00 ];
+	status = "okay";
+};
+
+&enet1 {
+	tbi-handle = <&tbi1>;
+	phy-handle = <&sgmii_phy03>;
+	phy-mode = "sgmii";
+	mac-address = [ 00 00 00 00 00 00 ];
+	status = "okay";
+};
+
+&enet2 {
+	phy-handle = <&rgmii_phy04>;
+	phy-mode = "rgmii-id";
+	mac-address = [ 00 00 00 00 00 00 ];
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	tlv320aic32x4: audio-codec@18 {
+		compatible = "ti,tlv320aic32x4";
+		reg = <0x18>;
+		clocks = <&audio_mclk>;
+		clock-names = "mclk";
+		ldoin-supply = <&reg_3p3v>;
+		iov-supply = <&reg_3p3v>;
+	};
+
+	pca9554_0: gpio-expander@20 {
+		compatible = "nxp,pca9554";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		vcc-supply = <&reg_3p3v>;
+		gpio-line-names = "BUTTON0", "BUTTON1",
+				  "BUTTON2", "EMMC_SEL",
+				  "DIP2", "DIP3",
+				  "EXT_TOUCH_INT", "GPIO_1";
+	};
+
+	pca9554_1: gpio-expander@21 {
+		compatible = "nxp,pca9554";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		vcc-supply = <&reg_3p3v>;
+		gpio-line-names = "PCIE_PWR_EN", "MPCIE_DISABLE#",
+				  "MPCIE_WAKE#", "LCD_BLT_EN",
+				  "LCD_PWR_EN", "EC1_PHY_PWDN",
+				  "EC3_PHY_PWDN", "SGMII_PHY_PWDN";
+	};
+
+	pca9554_2: gpio-expander@22 {
+		compatible = "nxp,pca9554";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&extirq>;
+		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		vcc-supply = <&reg_3p3v>;
+		gpio-line-names = "MUX_SEL0", "MUX_SEL1",
+				  "MUX_SEL2", "MUX_SEL3",
+				  "V95", "V96", "V97", "V98";
+	};
+
+	sii9022a: hdmi-transmitter@3b {
+		compatible = "sil,sii9022";
+		reg = <0x3b>;
+		iovcc-supply = <&reg_3p3v>;
+		cvcc12-supply = <&reg_1p2v>;
+		interrupts = <GIC_SPI 167 IRQ_TYPE_EDGE_RISING>;
+		#sound-dai-cells = <0>;
+		sil,i2s-data-lanes = <0>;
+		status = "disabled";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				sii9022a_in: endpoint {};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				sii9022a_out: endpoint {
+					remote-endpoint = <&hdmi_in>;
+				};
+			};
+		};
+	};
+
+	stmpe811: port-expander@41 {
+		compatible = "st,stmpe811";
+		reg = <0x41>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
+		vcc-supply = <&reg_3p3v>;
+		vio-supply = <&reg_3p3v>;
+
+		gpio {
+			compatible = "st,stmpe-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			/* GPIO 5-7 used for touch */
+			st,norequest-mask = <0xf0>;
+			gpio-line-names = "GPIO_ADC_I2C1_1",
+					  "GPIO_ADC_I2C1_2",
+					  "GPIO_ADC_I2C1_3",
+					  "GPIO_ADC_I2C1_4";
+		};
+
+		touchscreen {
+			compatible = "st,stmpe-ts";
+			status = "disabled";
+		};
+	};
+
+	pca9530: leds@60 {
+		compatible = "nxp,pca9530";
+		reg = <0x60>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "PWM_0", "PWM_1";
+
+		led-0 {
+			type = <PCA9532_TYPE_GPIO>;
+		};
+
+		led-1 {
+			type = <PCA9532_TYPE_GPIO>;
+		};
+	};
+
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&lpuart0 {
+	linux,rs485-enabled-at-boot-time;
+	status = "okay";
+};
+
+&mdio0 {
+	sgmii_phy03: ethernet-phy@3 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x03>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+		ti,dp83867-rxctrl-strap-quirk;
+	};
+
+	rgmii_phy04: ethernet-phy@4 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x04>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
+		ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+	};
+
+	rgmii_phy0c: ethernet-phy@c {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x0c>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
+		ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+	};
+};
+
+&pwm6 {
+	status = "okay";
+};
+
+&pwm7 {
+	status = "okay";
+};
+
+&sai1 {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&usb3 {
+	/*
+	 * Although DR connector, VBUS is always driven, so
+	 * restrict to host mode.
+	 */
+	dr_mode = "host";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a.dtsi b/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a.dtsi
new file mode 100644
index 000000000000..167559521ae1
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/ls/ls1021a-tqmls1021a.dtsi
@@ -0,0 +1,106 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2013-2014 Freescale Semiconductor, Inc.
+ * Copyright 2018-2023 TQ-Systems GmbH <linux@ew.tq-group.com>,
+ * D-82229 Seefeld, Germany.
+ * Author: Alexander Stein
+ */
+
+#include "ls1021a.dtsi"
+
+/ {
+	model = "TQMLS102xA SOM";
+	compatible = "tq,ls1021a-tqmls1021a", "fsl,ls1021a";
+
+	reg_3p3v_som: regulator-3p3v-som {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V_SOM";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+};
+
+&esdhc {
+	/* e-MMC over 8 data lines */
+	bus-width = <8>;
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	/* MC34VR500 DC/DC regulator at 0x8, managed by PMIC */
+	/* On-board PMC at 0x11 */
+
+	sa56004: temperature-sensor@4c {
+		compatible = "nxp,sa56004";
+		reg = <0x4c>;
+		vcc-supply = <&reg_3p3v_som>;
+	};
+
+	rtc0: rtc@51 {
+		compatible = "nxp,pcf85063a";
+		reg = <0x51>;
+		quartz-load-femtofarads = <12500>;
+	};
+
+	m24c64_54: eeprom@54 {
+		compatible = "atmel,24c64";
+		reg = <0x54>;
+		pagesize = <32>;
+		read-only;
+		vcc-supply = <&reg_3p3v_som>;
+	};
+};
+
+&mdio0 {
+	tbi1: tbi-phy@8 {
+		reg = <0x8>;
+		device_type = "tbi-phy";
+	};
+};
+
+&qspi {
+	status = "okay";
+
+	qflash0: flash@0 {
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <20000000>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <4>;
+		reg = <0>;
+		vcc-supply = <&reg_3p3v_som>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			uboot@0 {
+				label = "U-Boot-PBL";
+				reg = <0x0 0xe0000>;
+			};
+
+			env@e0000 {
+				label = "U-Boot Environment";
+				reg = <0xe0000 0x10000>;
+			};
+
+			dtb@f0000 {
+				label = "DTB";
+				reg = <0xf0000 0x10000>;
+			};
+
+			linux@100000 {
+				label = "Linux";
+				reg = <0x100000 0x700000>;
+			};
+
+			rootfs@800000 {
+				label = "RootFS";
+				reg = <0x800000 0x3800000>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/ls1021a-tsn.dts b/arch/arm/boot/dts/nxp/ls/ls1021a-tsn.dts
index 1ea32fff4120..da76566f3510 100644
--- a/arch/arm/boot/dts/ls1021a-tsn.dts
+++ b/arch/arm/boot/dts/nxp/ls/ls1021a-tsn.dts
@@ -40,8 +40,6 @@
 	/* ADG704BRMZ 1:4 SPI mux/demux */
 	sja1105: ethernet-switch@1 {
 		reg = <0x1>;
-		#address-cells = <1>;
-		#size-cells = <0>;
 		compatible = "nxp,sja1105t";
 		/* 12 MHz */
 		spi-max-frequency = <12000000>;
diff --git a/arch/arm/boot/dts/ls1021a-twr.dts b/arch/arm/boot/dts/nxp/ls/ls1021a-twr.dts
index f5c03871b205..38281b904301 100644
--- a/arch/arm/boot/dts/ls1021a-twr.dts
+++ b/arch/arm/boot/dts/nxp/ls/ls1021a-twr.dts
@@ -151,7 +151,7 @@
 	ranges = <0x0 0x0 0x0 0x60000000 0x08000000>;
 	status = "okay";
 
-	nor@0,0 {
+	flash@0,0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "cfi-flash";
diff --git a/arch/arm/boot/dts/ls1021a.dtsi b/arch/arm/boot/dts/nxp/ls/ls1021a.dtsi
index 2e69d6eab4d1..e0b9ea6dd510 100644
--- a/arch/arm/boot/dts/ls1021a.dtsi
+++ b/arch/arm/boot/dts/nxp/ls/ls1021a.dtsi
@@ -93,10 +93,9 @@
 			compatible = "fsl,qoriq-memory-controller";
 			reg = <0x0 0x1080000 0x0 0x1000>;
 			interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
-			big-endian;
 		};
 
-		gic: interrupt-controller@1400000 {
+		gic: interrupt-controller@1401000 {
 			compatible = "arm,gic-400", "arm,cortex-a7-gic";
 			#interrupt-cells = <3>;
 			interrupt-controller;
@@ -112,7 +111,7 @@
 			compatible = "fsl,ls1021a-msi";
 			reg = <0x0 0x1570e00 0x0 0x8>;
 			msi-controller;
-			interrupts =  <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
 		msi2: msi-controller@1570e08 {
@@ -122,13 +121,20 @@
 			interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
-		ifc: ifc@1530000 {
-			compatible = "fsl,ifc", "simple-bus";
+		ifc: memory-controller@1530000 {
+			compatible = "fsl,ifc";
 			reg = <0x0 0x1530000 0x0 0x10000>;
 			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 		};
 
+		sfp: efuse@1e80000 {
+			compatible = "fsl,ls1021a-sfp";
+			reg = <0x0 0x1e80000 0x0 0x10000>;
+			clocks = <&clockgen 4 3>;
+			clock-names = "sfp";
+		};
+
 		dcfg: dcfg@1ee0000 {
 			compatible = "fsl,ls1021a-dcfg", "syscon";
 			reg = <0x0 0x1ee0000 0x0 0x1000>;
@@ -148,14 +154,13 @@
 			status = "disabled";
 		};
 
-		esdhc: esdhc@1560000 {
+		esdhc: mmc@1560000 {
 			compatible = "fsl,ls1021a-esdhc", "fsl,esdhc";
 			reg = <0x0 0x1560000 0x0 0x10000>;
 			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <0>;
 			voltage-ranges = <1800 1800 3300 3300>;
 			sdhci,auto-cmd12;
-			big-endian;
 			bus-width = <4>;
 			status = "disabled";
 		};
@@ -192,7 +197,7 @@
 					<3 0 &gic GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>,
 					<4 0 &gic GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>,
 					<5 0 &gic GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-map-mask = <0xffffffff 0x0>;
+				interrupt-map-mask = <0x7 0x0>;
 			};
 		};
 
@@ -604,11 +609,10 @@
 		};
 
 		wdog0: watchdog@2ad0000 {
-			compatible = "fsl,imx21-wdt";
+			compatible = "fsl,ls1021a-wdt", "fsl,imx21-wdt";
 			reg = <0x0 0x2ad0000 0x0 0x10000>;
 			interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clockgen 4 1>;
-			clock-names = "wdog-en";
 			big-endian;
 		};
 
@@ -620,9 +624,9 @@
 			clocks = <&clockgen 4 1>, <&clockgen 4 1>,
 				 <&clockgen 4 1>, <&clockgen 4 1>;
 			clock-names = "bus", "mclk1", "mclk2", "mclk3";
-			dma-names = "tx", "rx";
-			dmas = <&edma0 1 47>,
-			       <&edma0 1 46>;
+			dma-names = "rx", "tx";
+			dmas = <&edma0 1 46>,
+			       <&edma0 1 47>;
 			status = "disabled";
 		};
 
@@ -634,13 +638,13 @@
 			clocks = <&clockgen 4 1>, <&clockgen 4 1>,
 				 <&clockgen 4 1>, <&clockgen 4 1>;
 			clock-names = "bus", "mclk1", "mclk2", "mclk3";
-			dma-names = "tx", "rx";
-			dmas = <&edma0 1 45>,
-			       <&edma0 1 44>;
+			dma-names = "rx", "tx";
+			dmas = <&edma0 1 44>,
+			       <&edma0 1 45>;
 			status = "disabled";
 		};
 
-		edma0: edma@2c00000 {
+		edma0: dma-controller@2c00000 {
 			#dma-cells = <2>;
 			compatible = "fsl,vf610-edma";
 			reg = <0x0 0x2c00000 0x0 0x10000>,
@@ -700,6 +704,7 @@
 
 		enet0: ethernet@2d10000 {
 			compatible = "fsl,etsec2";
+			reg = <0x0 0x2d10000 0x0 0x5000>;
 			device_type = "network";
 			#address-cells = <2>;
 			#size-cells = <2>;
@@ -710,8 +715,6 @@
 			dma-coherent;
 
 			queue-group@2d10000 {
-				#address-cells = <2>;
-				#size-cells = <2>;
 				reg = <0x0 0x2d10000 0x0 0x1000>;
 				interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>,
 					<GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
@@ -719,8 +722,6 @@
 			};
 
 			queue-group@2d14000  {
-				#address-cells = <2>;
-				#size-cells = <2>;
 				reg = <0x0 0x2d14000 0x0 0x1000>;
 				interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
 					<GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>,
@@ -730,6 +731,7 @@
 
 		enet1: ethernet@2d50000 {
 			compatible = "fsl,etsec2";
+			reg = <0x0 0x2d50000 0x0 0x5000>;
 			device_type = "network";
 			#address-cells = <2>;
 			#size-cells = <2>;
@@ -739,8 +741,6 @@
 			dma-coherent;
 
 			queue-group@2d50000  {
-				#address-cells = <2>;
-				#size-cells = <2>;
 				reg = <0x0 0x2d50000 0x0 0x1000>;
 				interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>,
 					<GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>,
@@ -748,8 +748,6 @@
 			};
 
 			queue-group@2d54000  {
-				#address-cells = <2>;
-				#size-cells = <2>;
 				reg = <0x0 0x2d54000 0x0 0x1000>;
 				interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
 					<GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
@@ -759,6 +757,7 @@
 
 		enet2: ethernet@2d90000 {
 			compatible = "fsl,etsec2";
+			reg = <0x0 0x2d90000 0x0 0x5000>;
 			device_type = "network";
 			#address-cells = <2>;
 			#size-cells = <2>;
@@ -768,8 +767,6 @@
 			dma-coherent;
 
 			queue-group@2d90000  {
-				#address-cells = <2>;
-				#size-cells = <2>;
 				reg = <0x0 0x2d90000 0x0 0x1000>;
 				interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>,
 					<GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>,
@@ -777,8 +774,6 @@
 			};
 
 			queue-group@2d94000  {
-				#address-cells = <2>;
-				#size-cells = <2>;
 				reg = <0x0 0x2d94000 0x0 0x1000>;
 				interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
 					<GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>,
@@ -801,6 +796,7 @@
 			dr_mode = "host";
 			snps,quirk-frame-length-adjustment = <0x20>;
 			snps,dis_rxdet_inp3_quirk;
+			usb3-lpm-capable;
 			snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
 		};
 
@@ -859,6 +855,7 @@
 			clocks = <&clockgen 4 1>, <&clockgen 4 1>;
 			clock-names = "ipg", "per";
 			big-endian;
+			status = "disabled";
 		};
 
 		can1: can@2a80000 {
@@ -868,6 +865,7 @@
 			clocks = <&clockgen 4 1>, <&clockgen 4 1>;
 			clock-names = "ipg", "per";
 			big-endian;
+			status = "disabled";
 		};
 
 		can2: can@2a90000 {
@@ -877,6 +875,7 @@
 			clocks = <&clockgen 4 1>, <&clockgen 4 1>;
 			clock-names = "ipg", "per";
 			big-endian;
+			status = "disabled";
 		};
 
 		can3: can@2aa0000 {
@@ -886,6 +885,7 @@
 			clocks = <&clockgen 4 1>, <&clockgen 4 1>;
 			clock-names = "ipg", "per";
 			big-endian;
+			status = "disabled";
 		};
 
 		ocram1: sram@10000000 {
@@ -904,7 +904,7 @@
 			ranges = <0x0 0x0 0x10010000 0x10000>;
 		};
 
-		qdma: dma-controller@8390000 {
+		qdma: dma-controller@8388000 {
 			compatible = "fsl,ls1021a-qdma";
 			reg = <0x0 0x8388000 0x0 0x1000>, /* Controller regs */
 			      <0x0 0x8389000 0x0 0x1000>, /* Status regs */
@@ -924,17 +924,15 @@
 			big-endian;
 		};
 
-		rcpm: power-controller@1ee2140 {
+		rcpm: wakeup-controller@1ee2140 {
 			compatible = "fsl,ls1021a-rcpm", "fsl,qoriq-rcpm-2.1+";
 			reg = <0x0 0x1ee2140 0x0 0x8>;
 			#fsl,rcpm-wakeup-cells = <2>;
-			#power-domain-cells = <0>;
 		};
 
-		ftm_alarm0: timer0@29d0000 {
+		ftm_alarm0: rtc@29d0000 {
 			compatible = "fsl,ls1021a-ftm-alarm";
 			reg = <0x0 0x29d0000 0x0 0x10000>;
-			reg-names = "ftm";
 			fsl,rcpm-wakeup = <&rcpm 0x0 0x20000000>;
 			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
 			big-endian;
diff --git a/arch/arm/boot/dts/nxp/mxs/Makefile b/arch/arm/boot/dts/nxp/mxs/Makefile
new file mode 100644
index 000000000000..d72ba702b6fa
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/Makefile
@@ -0,0 +1,35 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_MXS) += \
+	imx23-evk.dtb \
+	imx23-olinuxino.dtb \
+	imx23-sansa.dtb \
+	imx23-stmp378x_devb.dtb \
+	imx23-xfi3.dtb \
+	imx28-amarula-rmm.dtb \
+	imx28-apf28.dtb \
+	imx28-apf28dev.dtb \
+	imx28-apx4devkit.dtb \
+	imx28-btt3-0.dtb \
+	imx28-btt3-1.dtb \
+	imx28-btt3-2.dtb \
+	imx28-cfa10036.dtb \
+	imx28-cfa10037.dtb \
+	imx28-cfa10049.dtb \
+	imx28-cfa10055.dtb \
+	imx28-cfa10056.dtb \
+	imx28-cfa10057.dtb \
+	imx28-cfa10058.dtb \
+	imx28-duckbill-2-485.dtb \
+	imx28-duckbill-2.dtb \
+	imx28-duckbill-2-enocean.dtb \
+	imx28-duckbill-2-spi.dtb \
+	imx28-duckbill.dtb \
+	imx28-eukrea-mbmx283lc.dtb \
+	imx28-eukrea-mbmx287lc.dtb \
+	imx28-evk.dtb \
+	imx28-m28cu3.dtb \
+	imx28-m28evk.dtb \
+	imx28-sps1.dtb \
+	imx28-ts4600.dtb \
+	imx28-tx28.dtb \
+	imx28-xea.dtb
diff --git a/arch/arm/boot/dts/imx23-evk.dts b/arch/arm/boot/dts/nxp/mxs/imx23-evk.dts
index 3b609d987d88..33b36af1656f 100644
--- a/arch/arm/boot/dts/imx23-evk.dts
+++ b/arch/arm/boot/dts/nxp/mxs/imx23-evk.dts
@@ -52,7 +52,7 @@
 	};
 
 	apb@80000000 {
-		apbh@80000000 {
+		apbh-bus@80000000 {
 			nand-controller@8000c000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&gpmi_pins_a &gpmi_pins_fixup>;
@@ -99,7 +99,7 @@
 			};
 		};
 
-		apbx@80040000 {
+		apbx-bus@80040000 {
 			lradc@80050000 {
 				status = "okay";
 				fsl,lradc-touchscreen-wires = <4>;
@@ -137,7 +137,7 @@
 
 	backlight_display: backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm 2 5000000>;
+		pwms = <&pwm 2 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
 	};
diff --git a/arch/arm/boot/dts/imx23-olinuxino.dts b/arch/arm/boot/dts/nxp/mxs/imx23-olinuxino.dts
index 0729e72f2283..e372e9327a47 100644
--- a/arch/arm/boot/dts/imx23-olinuxino.dts
+++ b/arch/arm/boot/dts/nxp/mxs/imx23-olinuxino.dts
@@ -19,7 +19,7 @@
 	};
 
 	apb@80000000 {
-		apbh@80000000 {
+		apbh-bus@80000000 {
 			ssp0: spi@80010000 {
 				compatible = "fsl,imx23-mmc";
 				pinctrl-names = "default";
@@ -64,7 +64,7 @@
 			};
 		};
 
-		apbx@80040000 {
+		apbx-bus@80040000 {
 			lradc@80050000 {
 				status = "okay";
 			};
@@ -101,21 +101,14 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_usb0_vbus: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "usb0_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			startup-delay-us = <300>; /* LAN9215 requires a POR of 200us minimum */
-			gpio = <&gpio0 17 0>;
-		};
+	reg_usb0_vbus: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb0_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		startup-delay-us = <300>; /* LAN9215 requires a POR of 200us minimum */
+		gpio = <&gpio0 17 0>;
 	};
 
 	leds {
diff --git a/arch/arm/boot/dts/imx23-pinfunc.h b/arch/arm/boot/dts/nxp/mxs/imx23-pinfunc.h
index 5c0f32ca3a93..468c079f3c2b 100644
--- a/arch/arm/boot/dts/imx23-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/mxs/imx23-pinfunc.h
@@ -1,14 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Header providing constants for i.MX23 pinctrl bindings.
  *
  * Copyright (C) 2013 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
  */
 
 #ifndef __DT_BINDINGS_MX23_PINCTRL_H__
diff --git a/arch/arm/boot/dts/imx23-sansa.dts b/arch/arm/boot/dts/nxp/mxs/imx23-sansa.dts
index 46057d9bf555..613f13b6c8a8 100644
--- a/arch/arm/boot/dts/imx23-sansa.dts
+++ b/arch/arm/boot/dts/nxp/mxs/imx23-sansa.dts
@@ -55,7 +55,7 @@
 	};
 
 	apb@80000000 {
-		apbh@80000000 {
+		apbh-bus@80000000 {
 			ssp0: spi@80010000 {
 				compatible = "fsl,imx23-mmc";
 				pinctrl-names = "default";
@@ -93,14 +93,14 @@
 						MX23_PAD_LCD_HSYNC__GPIO_1_24
 						MX23_PAD_PWM3__GPIO_1_29
 					>;
-					fsl,drive-strength = <0>;
-					fsl,voltage = <1>;
-					fsl,pull-up = <0>;
+					fsl,drive-strength = <MXS_DRIVE_4mA>;
+					fsl,voltage = <MXS_VOLTAGE_HIGH>;
+					fsl,pull-up = <MXS_PULL_DISABLE>;
 				};
 			};
 		};
 
-		apbx@80040000 {
+		apbx-bus@80040000 {
 			pwm: pwm@80064000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&pwm2_pins_a>;
@@ -166,7 +166,7 @@
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm 2 5000000>;
+		pwms = <&pwm 2 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
 	};
@@ -175,10 +175,8 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "i2c-gpio";
-		gpios = <
-			&gpio1 24 0		/* SDA */
-			&gpio1 22 0		/* SCL */
-		>;
+		sda-gpios = <&gpio1 24 0>;
+		scl-gpios = <&gpio1 22 0>;
 		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
 	};
 
@@ -186,10 +184,8 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "i2c-gpio";
-		gpios = <
-			&gpio0 31 0		/* SDA */
-			&gpio0 30 0		/* SCL */
-		>;
+		sda-gpios = <&gpio0 31 0>;
+		scl-gpios = <&gpio0 30 0>;
 		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
 
 		touch: touch@20 {
diff --git a/arch/arm/boot/dts/imx23-stmp378x_devb.dts b/arch/arm/boot/dts/nxp/mxs/imx23-stmp378x_devb.dts
index da4b88f32eaa..b2b6f8514999 100644
--- a/arch/arm/boot/dts/imx23-stmp378x_devb.dts
+++ b/arch/arm/boot/dts/nxp/mxs/imx23-stmp378x_devb.dts
@@ -16,7 +16,7 @@
 	};
 
 	apb@80000000 {
-		apbh@80000000 {
+		apbh-bus@80000000 {
 			ssp0: spi@80010000 {
 				compatible = "fsl,imx23-mmc";
 				pinctrl-names = "default";
@@ -44,7 +44,7 @@
 			};
 		};
 
-		apbx@80040000 {
+		apbx-bus@80040000 {
 			auart0: serial@8006c000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&auart0_pins_a>;
@@ -59,18 +59,11 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_vddio_sd0: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "vddio-sd0";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio1 29 0>;
-		};
+	reg_vddio_sd0: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vddio-sd0";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio1 29 0>;
 	};
 };
diff --git a/arch/arm/boot/dts/imx23-xfi3.dts b/arch/arm/boot/dts/nxp/mxs/imx23-xfi3.dts
index a6213c590f94..fad08f6c008f 100644
--- a/arch/arm/boot/dts/imx23-xfi3.dts
+++ b/arch/arm/boot/dts/nxp/mxs/imx23-xfi3.dts
@@ -54,7 +54,7 @@
 	};
 
 	apb@80000000 {
-		apbh@80000000 {
+		apbh-bus@80000000 {
 			ssp0: spi@80010000 {
 				compatible = "fsl,imx23-mmc";
 				pinctrl-names = "default";
@@ -83,9 +83,9 @@
 					fsl,pinmux-ids = <
 						MX23_PAD_GPMI_D07__GPIO_0_7
 					>;
-					fsl,drive-strength = <0>;
-					fsl,voltage = <1>;
-					fsl,pull-up = <0>;
+					fsl,drive-strength = <MXS_DRIVE_4mA>;
+					fsl,voltage = <MXS_VOLTAGE_HIGH>;
+					fsl,pull-up = <MXS_PULL_DISABLE>;
 				};
 
 				key_pins_a: keys@0 {
@@ -94,14 +94,14 @@
 						MX23_PAD_ROTARYA__GPIO_2_7
 						MX23_PAD_ROTARYB__GPIO_2_8
 					>;
-					fsl,drive-strength = <0>;
-					fsl,voltage = <1>;
-					fsl,pull-up = <1>;
+					fsl,drive-strength = <MXS_DRIVE_4mA>;
+					fsl,voltage = <MXS_VOLTAGE_HIGH>;
+					fsl,pull-up = <MXS_PULL_ENABLE>;
 				};
 			};
 		};
 
-		apbx@80040000 {
+		apbx-bus@80040000 {
 			i2c: i2c@80058000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&i2c_pins_a>;
@@ -153,24 +153,24 @@
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm 2 5000000>;
+		pwms = <&pwm 2 5000000 0>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&key_pins_a>;
 
-		voldown {
+		key-voldown {
 			label = "volume-down";
 			linux,code = <114>;
 			gpios = <&gpio2 7 0>;
 			debounce-interval = <20>;
 		};
 
-		volup {
+		key-volup {
 			label = "volume-up";
 			linux,code = <115>;
 			gpios = <&gpio2 8 0>;
diff --git a/arch/arm/boot/dts/imx23.dtsi b/arch/arm/boot/dts/nxp/mxs/imx23.dtsi
index 7f4c602454a5..5e21252fb7c9 100644
--- a/arch/arm/boot/dts/imx23.dtsi
+++ b/arch/arm/boot/dts/nxp/mxs/imx23.dtsi
@@ -45,7 +45,7 @@
 		reg = <0x80000000 0x80000>;
 		ranges;
 
-		apbh@80000000 {
+		apbh-bus@80000000 {
 			compatible = "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -59,13 +59,11 @@
 				reg = <0x80000000 0x2000>;
 			};
 
-			dma_apbh: dma-apbh@80004000 {
+			dma_apbh: dma-controller@80004000 {
 				compatible = "fsl,imx23-dma-apbh";
 				reg = <0x80004000 0x2000>;
-				interrupts = <0 14 20 0
-					      13 13 13 13>;
-				interrupt-names = "empty", "ssp0", "ssp1", "empty",
-						  "gpmi0", "gpmi1", "gpmi2", "gpmi3";
+				interrupts = <0>, <14>, <20>, <0>,
+					     <13>, <13>, <13>, <13>;
 				#dma-cells = <1>;
 				dma-channels = <8>;
 				clocks = <&clks 15>;
@@ -112,7 +110,7 @@
 				reg = <0x80018000 0x2000>;
 
 				gpio0: gpio@0 {
-					compatible = "fsl,imx23-gpio", "fsl,mxs-gpio";
+					compatible = "fsl,imx23-gpio";
 					reg = <0>;
 					interrupts = <16>;
 					gpio-controller;
@@ -122,7 +120,7 @@
 				};
 
 				gpio1: gpio@1 {
-					compatible = "fsl,imx23-gpio", "fsl,mxs-gpio";
+					compatible = "fsl,imx23-gpio";
 					reg = <1>;
 					interrupts = <17>;
 					gpio-controller;
@@ -132,7 +130,7 @@
 				};
 
 				gpio2: gpio@2 {
-					compatible = "fsl,imx23-gpio", "fsl,mxs-gpio";
+					compatible = "fsl,imx23-gpio";
 					reg = <2>;
 					interrupts = <18>;
 					gpio-controller;
@@ -414,13 +412,13 @@
 				status = "disabled";
 			};
 
-			dma_apbx: dma-apbx@80024000 {
+			dma_apbx: dma-controller@80024000 {
 				compatible = "fsl,imx23-dma-apbx";
 				reg = <0x80024000 0x2000>;
-				interrupts = <7 5 9 26
-					      19 0 25 23
-					      60 58 9 0
-					      0 0 0 0>;
+				interrupts = <7>, <5>, <9>, <26>,
+					     <19>, <0>, <25>, <23>,
+					     <60>, <58>, <9>, <0>,
+					     <0>, <0>, <0>, <0>;
 				interrupt-names = "audio-adc", "audio-dac", "spdif-tx", "i2c",
 						  "saif0", "empty", "auart0-rx", "auart0-tx",
 						  "auart1-rx", "auart1-tx", "saif1", "empty",
@@ -433,7 +431,7 @@
 			dcp: crypto@80028000 {
 				compatible = "fsl,imx23-dcp";
 				reg = <0x80028000 0x2000>;
-				interrupts = <53 54>;
+				interrupts = <53>, <54>;
 				status = "okay";
 			};
 
@@ -458,7 +456,7 @@
 			lcdif@80030000 {
 				compatible = "fsl,imx23-lcdif";
 				reg = <0x80030000 2000>;
-				interrupts = <46 45>;
+				interrupts = <46>, <45>;
 				clocks = <&clks 38>;
 				status = "disabled";
 			};
@@ -478,7 +476,7 @@
 			};
 		};
 
-		apbx@80040000 {
+		apbx-bus@80040000 {
 			compatible = "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -486,7 +484,7 @@
 			ranges;
 
 			clks: clkctrl@80040000 {
-				compatible = "fsl,imx23-clkctrl", "fsl,clkctrl";
+				compatible = "fsl,imx23-clkctrl";
 				reg = <0x80040000 0x2000>;
 				#clock-cells = <1>;
 			};
@@ -527,7 +525,8 @@
 			lradc: lradc@80050000 {
 				compatible = "fsl,imx23-lradc";
 				reg = <0x80050000 0x2000>;
-				interrupts = <36 37 38 39 40 41 42 43 44>;
+				interrupts = <36>, <37>, <38>, <39>, <40>,
+					     <41>, <42>, <43>, <44>;
 				status = "disabled";
 				clocks = <&clks 26>;
 				#io-channel-cells = <1>;
@@ -562,7 +561,7 @@
 				compatible = "fsl,imx23-pwm";
 				reg = <0x80064000 0x2000>;
 				clocks = <&clks 30>;
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				fsl,pwm-number = <5>;
 				status = "disabled";
 			};
@@ -570,7 +569,7 @@
 			timrot@80068000 {
 				compatible = "fsl,imx23-timrot", "fsl,timrot";
 				reg = <0x80068000 0x2000>;
-				interrupts = <28 29 30 31>;
+				interrupts = <28>, <29>, <30>, <31>;
 				clocks = <&clks 28>;
 			};
 
@@ -599,7 +598,7 @@
 				reg = <0x80070000 0x2000>;
 				interrupts = <0>;
 				clocks = <&clks 32>, <&clks 16>;
-				clock-names = "uart", "apb_pclk";
+				clock-names = "uartclk", "apb_pclk";
 				status = "disabled";
 			};
 
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-amarula-rmm.dts b/arch/arm/boot/dts/nxp/mxs/imx28-amarula-rmm.dts
new file mode 100644
index 000000000000..af59211842fb
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-amarula-rmm.dts
@@ -0,0 +1,300 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2025 Amarula Solutions, Dario Binacchi <dario.binacchi@amarulasolutions.com>
+ */
+
+/dts-v1/;
+
+#include "imx28.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "amarula,imx28-rmm", "fsl,imx28";
+	model = "Amarula i.MX28 rmm";
+
+	memory@40000000 {
+		reg = <0x40000000 0x08000000>;
+		device_type = "memory";
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 4 5000000 0>;
+		brightness-levels = <0 255>;
+		num-interpolated-steps = <255>;
+		default-brightness-level = <255>;
+		power-supply = <&reg_5v>;
+	};
+
+	beeper {
+		compatible = "pwm-beeper";
+		pwms = <&pwm 7 100000 0>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&leds_pins>;
+
+		led-0 {
+			gpios = <&gpio2 7 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-1 {
+			gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-2 {
+			gpios = <&gpio3 17 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	reg_1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	reg_fec_3v3: regulator-fec-3v3 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&fec_3v3_enable_pin>;
+		regulator-name = "fec-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <300000>;
+		vin-supply = <&reg_5v>;
+	};
+
+	reg_usb0_vbus: regulator-usb0-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb0_vbus_enable_pin>;
+		regulator-name = "usb0_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio2 5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	reg_usb1_vbus: regulator-usb1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb1_vbus_enable_pin>;
+		regulator-name = "usb1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio2 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+};
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_2pins_a>;
+	status = "okay";
+};
+
+&auart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart1_pins_a>;
+	status = "okay";
+};
+
+&can0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&can0_pins_a>;
+	status = "okay";
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_b>;
+	status = "okay";
+};
+
+&duart_pins_b {
+	fsl,voltage = <MXS_VOLTAGE_LOW>;
+};
+
+&gpmi {
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+
+	touchscreen: touchscreen@38 {
+		compatible = "edt,edt-ft5306";
+		reg = <0x38>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&edt_ft5x06_pins &edt_ft5x06_wake_pin>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <19 IRQ_TYPE_EDGE_RISING>;
+		reset-gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
+		wake-gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&lradc {
+	status = "okay";
+};
+
+&mac0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>;
+	phy-mode = "rmii";
+	phy-supply = <&reg_fec_3v3>;
+	phy-handle = <&ethphy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			max-speed = <100>;
+			reset-gpios = <&gpio3 28 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <4000>;
+			reset-deassert-us = <4000>;
+		};
+	};
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a>;
+
+	edt_ft5x06_pins: edt-ft5x06@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_RDY1__GPIO_0_21 /* Reset */
+			MX28_PAD_GPMI_CE3N__GPIO_0_19 /* Interrupt */
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+	};
+
+	edt_ft5x06_wake_pin: edt-ft5x06-wake@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <MX28_PAD_GPMI_CE2N__GPIO_0_18>;
+		fsl,drive-strength = <MXS_DRIVE_16mA>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+	};
+
+	fec_3v3_enable_pin: fec-3v3-enable@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <MX28_PAD_SPDIF__GPIO_3_27>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+	};
+
+	hog_pins_a: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP2_SS1__GPIO_2_20  /* External power */
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+	};
+
+	leds_pins: leds@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP0_DATA7__GPIO_2_7
+			MX28_PAD_PWM0__GPIO_3_16
+			MX28_PAD_PWM1__GPIO_3_17
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+	};
+
+	usb0_vbus_enable_pin: usb0-vbus-enable@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <MX28_PAD_SSP0_DATA5__GPIO_2_5>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+	};
+
+	usb1_vbus_enable_pin: usb1-vbus-enable@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <MX28_PAD_SSP0_DATA6__GPIO_2_6>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm4_pins_a &pwm7_pins_a>;
+	status = "okay";
+};
+
+/* microSD */
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_sck_cfg>;
+	broken-cd;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&usb0 {
+	dr_mode = "host";
+	vbus-supply = <&reg_usb0_vbus>;
+	status = "okay";
+};
+
+&usb1 {
+	dr_mode = "host";
+	vbus-supply = <&reg_usb1_vbus>;
+	status = "okay";
+};
+
+&usbphy0 {
+	status = "okay";
+};
+
+&usbphy1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-apf28.dts b/arch/arm/boot/dts/nxp/mxs/imx28-apf28.dts
new file mode 100644
index 000000000000..98672932e41b
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-apf28.dts
@@ -0,0 +1,72 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 Armadeus Systems - <support@armadeus.com>
+ */
+
+/dts-v1/;
+#include "imx28.dtsi"
+
+/ {
+	model = "Armadeus Systems APF28 module";
+	compatible = "armadeus,imx28-apf28", "fsl,imx28";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x08000000>;
+	};
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_a>;
+	status = "okay";
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
+	status = "okay";
+
+	partition@0 {
+		label = "u-boot";
+		reg = <0x0 0x300000>;
+	};
+
+	partition@300000 {
+		label = "env";
+		reg = <0x300000 0x80000>;
+	};
+
+	partition@380000 {
+		label = "env2";
+		reg = <0x380000 0x80000>;
+	};
+
+	partition@400000 {
+		label = "dtb";
+		reg = <0x400000 0x80000>;
+	};
+
+	partition@480000 {
+		label = "splash";
+		reg = <0x480000 0x80000>;
+	};
+
+	partition@500000 {
+		label = "kernel";
+		reg = <0x500000 0x800000>;
+	};
+
+	partition@d00000 {
+		label = "rootfs";
+		reg = <0xd00000 0xf300000>;
+	};
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>;
+	phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-apf28dev.dts b/arch/arm/boot/dts/nxp/mxs/imx28-apf28dev.dts
new file mode 100644
index 000000000000..6c87266eb135
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-apf28dev.dts
@@ -0,0 +1,209 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 Armadeus Systems - <support@armadeus.com>
+ */
+
+/* APF28Dev is a docking board for the APF28 SOM */
+#include "imx28-apf28.dts"
+
+/ {
+	model = "Armadeus Systems APF28Dev docking/development board";
+	compatible = "armadeus,imx28-apf28dev", "armadeus,imx28-apf28", "fsl,imx28";
+
+	reg_usb0_vbus: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb0_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 23 1>;
+		enable-active-high;
+	};
+
+	reg_can0_vcc: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "can0_vcc";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		user {
+			label = "Heartbeat";
+			gpios = <&gpio0 21 0>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+
+		pwms = <&pwm 3 191000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		user-button {
+			label = "User button";
+			gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
+			linux,code = <0x100>;
+			wakeup-source;
+		};
+	};
+};
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_pins_a>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&can0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&can0_pins_a>;
+	xceiver-supply = <&reg_can0_vcc>;
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_16bit_pins_a
+		     &lcdif_pins_apf28dev>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <16>;
+		bus-width = <16>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <33000033>;
+				hactive = <800>;
+				vactive = <480>;
+				hback-porch = <96>;
+				hfront-porch = <96>;
+				vback-porch = <20>;
+				vfront-porch = <21>;
+				hsync-len = <64>;
+				vsync-len = <4>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+				de-active = <1>;
+				pixelclk-active = <0>;
+			};
+		};
+	};
+};
+
+&lradc {
+	fsl,lradc-touchscreen-wires = <4>;
+	status = "okay";
+};
+
+&mac1 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac1_pins_a>;
+	phy-reset-gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_apf28dev>;
+
+	hog_pins_apf28dev: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_D16__GPIO_1_16
+			MX28_PAD_LCD_D17__GPIO_1_17
+			MX28_PAD_LCD_D18__GPIO_1_18
+			MX28_PAD_LCD_D19__GPIO_1_19
+			MX28_PAD_LCD_D20__GPIO_1_20
+			MX28_PAD_LCD_D21__GPIO_1_21
+			MX28_PAD_LCD_D22__GPIO_1_22
+			MX28_PAD_GPMI_CE1N__GPIO_0_17
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_apf28dev: lcdif-apf28dev@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RD_E__LCD_VSYNC
+			MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+			MX28_PAD_LCD_RS__LCD_DOTCLK
+			MX28_PAD_LCD_CS__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	usb0_otg_apf28dev: otg-apf28dev@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_D23__GPIO_1_23
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm3_pins_a &pwm4_pins_a>;
+	status = "okay";
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_4bit_pins_a
+		     &mmc0_cd_cfg &mmc0_sck_cfg>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&ssp2 {
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "okay";
+};
+
+&usb0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_otg_apf28dev
+		     &usb0_id_pins_b>;
+	vbus-supply = <&reg_usb0_vbus>;
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
+
+&usbphy0 {
+	status = "okay";
+};
+
+&usbphy1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-apx4devkit.dts b/arch/arm/boot/dts/nxp/mxs/imx28-apx4devkit.dts
new file mode 100644
index 000000000000..0d845ca81e89
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-apx4devkit.dts
@@ -0,0 +1,226 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "imx28.dtsi"
+
+/ {
+	model = "Bluegiga APX4 Development Kit";
+	compatible = "bluegiga,apx4devkit", "fsl,imx28";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x04000000>;
+	};
+
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	sound {
+		compatible = "bluegiga,apx4devkit-sgtl5000",
+			     "fsl,mxs-audio-sgtl5000";
+		model = "apx4devkit-sgtl5000";
+		saif-controllers = <&saif0 &saif1>;
+		audio-codec = <&sgtl5000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		user {
+			label = "Heartbeat";
+			gpios = <&gpio3 28 0>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_pins_a>;
+	status = "okay";
+};
+
+&auart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart1_2pins_a>;
+	status = "okay";
+};
+
+&auart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart2_2pins_a>;
+	status = "okay";
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_a>;
+	status = "okay";
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
+	status = "okay";
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_24bit_pins_a
+		     &lcdif_pins_apx4>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <32>;
+		bus-width = <24>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <30000000>;
+				hactive = <800>;
+				vactive = <480>;
+				hback-porch = <88>;
+				hfront-porch = <40>;
+				vback-porch = <32>;
+				vfront-porch = <13>;
+				hsync-len = <48>;
+				vsync-len = <3>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+				de-active = <1>;
+				pixelclk-active = <0>;
+			};
+		};
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+
+	sgtl5000: codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		VDDA-supply = <&reg_3p3v>;
+		VDDIO-supply = <&reg_3p3v>;
+		clocks = <&saif0>;
+	};
+
+	pcf8563: rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>;
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a>;
+
+	hog_pins_a: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_CE1N__GPIO_0_17
+			MX28_PAD_GPMI_RDY1__GPIO_0_21
+			MX28_PAD_SSP2_MISO__GPIO_2_18
+			MX28_PAD_SSP2_SS0__AUART3_TX /* was: 0x2131 - MX28_PAD_SSP2_SS0__GPIO_2_19 */
+			MX28_PAD_PWM3__GPIO_3_28
+			MX28_PAD_LCD_RESET__GPIO_3_30
+			MX28_PAD_JTAG_RTCK__GPIO_4_20
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_apx4: lcdif-apx4@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RD_E__LCD_VSYNC
+			MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+			MX28_PAD_LCD_RS__LCD_DOTCLK
+			MX28_PAD_LCD_CS__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	mmc2_4bit_pins_apx4: mmc2-4bit-apx4@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP0_DATA4__SSP2_D0
+			MX28_PAD_SSP0_DATA5__SSP2_D3
+			MX28_PAD_SSP0_DATA6__SSP2_CMD
+			MX28_PAD_SSP0_DATA7__SSP2_SCK
+			MX28_PAD_SSP2_SS1__SSP2_D1
+			MX28_PAD_SSP2_SS2__SSP2_D2
+		>;
+		fsl,drive-strength = <MXS_DRIVE_8mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	mmc2_sck_cfg_apx4: mmc2-sck-cfg-apx4@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP0_DATA7__SSP2_SCK
+		>;
+		fsl,drive-strength = <MXS_DRIVE_12mA>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&saif0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif0_pins_a>;
+	status = "okay";
+};
+
+&saif1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif1_pins_a>;
+	fsl,saif-master = <&saif0>;
+	status = "okay";
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_sck_cfg>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&ssp2 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_4bit_pins_apx4 &mmc2_sck_cfg_apx4>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&usb1 {
+      status = "okay";
+};
+
+&usbphy1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb1_pins_a>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dts b/arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dts
new file mode 100644
index 000000000000..6ac46e4b21bb
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-btt3-0.dts
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2024
+ * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
+ */
+
+/dts-v1/;
+#include "imx28-btt3.dtsi"
+
+&hog_pins_rev {
+	fsl,pull-up = <MXS_PULL_ENABLE>;
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dts b/arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dts
new file mode 100644
index 000000000000..213fe931c58b
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-btt3-1.dts
@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2024
+ * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
+ */
+
+/dts-v1/;
+#include "imx28-btt3.dtsi"
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dts b/arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dts
new file mode 100644
index 000000000000..4bccd784d065
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-btt3-2.dts
@@ -0,0 +1,39 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2024
+ * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
+ */
+
+/dts-v1/;
+#include "imx28-btt3.dtsi"
+
+/ {
+	panel {
+		compatible = "powertip,st7272", "panel-dpi";
+		power-supply = <&reg_3v3>;
+		width-mm = <70>;
+		height-mm = <52>;
+
+		panel-timing {
+			clock-frequency = <6500000>;
+			hactive = <320>;
+			vactive = <240>;
+			hfront-porch = <20>;
+			hback-porch = <68>;
+			hsync-len = <30>;
+			vfront-porch = <4>;
+			vback-porch = <14>;
+			vsync-len = <4>;
+			hsync-active = <0>;
+			vsync-active = <0>;
+			de-active = <1>;
+			pixelclk-active = <1>;
+		};
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-btt3.dtsi b/arch/arm/boot/dts/nxp/mxs/imx28-btt3.dtsi
new file mode 100644
index 000000000000..a6903ef2b093
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-btt3.dtsi
@@ -0,0 +1,313 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2024
+ * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
+ */
+/dts-v1/;
+#include "imx28-lwe.dtsi"
+
+/ {
+	model = "BTT3";
+
+	compatible = "lwn,imx28-btt3", "fsl,imx28";
+
+	chosen {
+	       bootargs = "root=/dev/mmcblk0p2 rootfstype=ext4 ro rootwait console=ttyAMA0,115200 panic=1 quiet";
+	};
+
+	memory@40000000 {
+		reg = <0x40000000 0x10000000>;
+		device_type = "memory";
+	};
+
+	panel {
+		compatible = "powertip,hx8238a", "panel-dpi";
+		power-supply = <&reg_3v3>;
+		width-mm = <70>;
+		height-mm = <52>;
+
+		panel-timing {
+			clock-frequency = <6500000>;
+			hactive = <320>;
+			vactive = <240>;
+			hfront-porch = <20>;
+			hback-porch = <38>;
+			hsync-len = <30>;
+			vfront-porch = <4>;
+			vback-porch = <14>;
+			vsync-len = <4>;
+			hsync-active = <0>;
+			vsync-active = <0>;
+			de-active = <0>;
+			pixelclk-active = <1>;
+		};
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
+	poweroff {
+		compatible = "gpio-poweroff";
+		gpios = <&gpio0 24 GPIO_ACTIVE_HIGH>;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "BTTC Audio";
+		simple-audio-card,widgets = "Speaker", "BTTC Speaker";
+		simple-audio-card,routing = "BTTC Speaker", "SPKOUTN", "BTTC Speaker", "SPKOUTP";
+
+		simple-audio-card,dai-link@0 {
+			format = "left_j";
+			bitclock-master = <&dai0_master>;
+			frame-master = <&dai0_master>;
+			mclk-fs = <256>;
+
+			dai0_master: cpu {
+				sound-dai = <&saif0>;
+			};
+
+			codec {
+				sound-dai = <&wm89xx>;
+				clocks = <&saif0>;
+			};
+		};
+	};
+
+	wifi_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_en_pin_bttc>;
+		reset-gpios = <&gpio0 27 GPIO_ACTIVE_LOW>;
+		/* W1-163 needs 60us for WL_EN to be low and */
+		/* 150ms after high before downloading FW is possible */
+		post-power-on-delay-ms = <200>;
+		power-off-delay-us = <100>;
+	};
+};
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_2pins_a>;
+	status = "okay";
+};
+
+&auart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart3_pins_a>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&i2c0 {
+	wm89xx: audio-codec@1a {
+		compatible = "wlf,wm8940";
+		reg = <0x1a>;
+		#sound-dai-cells = <0>;
+	};
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_24bit_pins_a>, <&lcdif_sync_pins_bttc>,
+		    <&lcdif_reset_pins_bttc>;
+	status = "okay";
+
+	port {
+		display_out: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
+};
+
+&mac0 {
+	clocks = <&clks 57>, <&clks 57>, <&clks 64>;
+	clock-names = "ipg", "ahb", "enet_out";
+	phy-handle = <&mac0_phy>;
+	phy-mode = "rmii";
+	phy-supply = <&reg_3v3>;
+	/*
+	 * This MAC address is adjusted during production.
+	 * Value specified below is used as a fallback during recovery.
+	 */
+	local-mac-address = [ 00 11 B8 00 BF 8A ];
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mac0_phy: ethernet-phy@0 {
+			/* LAN8720Ai - PHY ID */
+			compatible = "ethernet-phy-id0007.c0f0","ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			smsc,disable-energy-detect;
+			max-speed = <100>;
+			reset-gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <1000>;
+			reset-deassert-us = <1000>;
+		};
+	};
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a>, <&hog_pins_rev>;
+
+	hog_pins_a: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_RDY2__GPIO_0_22
+			MX28_PAD_GPMI_RDY3__GPIO_0_23
+			MX28_PAD_GPMI_RDN__GPIO_0_24
+			MX28_PAD_LCD_VSYNC__GPIO_1_28
+			MX28_PAD_SSP2_SS1__GPIO_2_20
+			MX28_PAD_SSP2_SS2__GPIO_2_21
+			MX28_PAD_AUART2_CTS__GPIO_3_10
+			MX28_PAD_AUART2_RTS__GPIO_3_11
+			MX28_PAD_GPMI_WRN__GPIO_0_25
+			MX28_PAD_ENET0_RXD2__GPIO_4_9
+			MX28_PAD_ENET0_TXD2__GPIO_4_11
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	hog_pins_rev: hog@1 {
+		reg = <1>;
+		fsl,pinmux-ids = <
+			MX28_PAD_ENET0_RXD3__GPIO_4_10
+			MX28_PAD_ENET0_TX_CLK__GPIO_4_5
+			MX28_PAD_ENET0_COL__GPIO_4_14
+			MX28_PAD_ENET0_CRS__GPIO_4_15
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	keypad_pins_bttc: keypad-bttc@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_D00__GPIO_0_0
+			MX28_PAD_AUART0_CTS__GPIO_3_2
+			MX28_PAD_AUART0_RTS__GPIO_3_3
+			MX28_PAD_GPMI_D03__GPIO_0_3
+			MX28_PAD_GPMI_D04__GPIO_0_4
+			MX28_PAD_GPMI_D05__GPIO_0_5
+			MX28_PAD_GPMI_D06__GPIO_0_6
+			MX28_PAD_GPMI_D07__GPIO_0_7
+			MX28_PAD_GPMI_CE1N__GPIO_0_17
+			MX28_PAD_GPMI_CE2N__GPIO_0_18
+			MX28_PAD_GPMI_CE3N__GPIO_0_19
+			MX28_PAD_GPMI_RDY0__GPIO_0_20
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_sync_pins_bttc: lcdif-bttc@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
+			MX28_PAD_LCD_ENABLE__LCD_ENABLE
+			MX28_PAD_LCD_HSYNC__LCD_HSYNC
+			MX28_PAD_LCD_RD_E__LCD_VSYNC
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_reset_pins_bttc: lcdif-bttc@1 {
+		reg = <1>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RESET__GPIO_3_30
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	ssp1_sdio_pins_a: ssp1-sdio@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP1_DATA0__SSP1_D0
+			MX28_PAD_GPMI_D01__SSP1_D1
+			MX28_PAD_GPMI_D02__SSP1_D2
+			MX28_PAD_SSP1_DATA3__SSP1_D3
+			MX28_PAD_SSP1_CMD__SSP1_CMD
+			MX28_PAD_SSP1_SCK__SSP1_SCK
+		>;
+		fsl,drive-strength = <MXS_DRIVE_8mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	wifi_en_pin_bttc: wifi-en-pin@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_CLE__GPIO_0_27
+		>;
+		fsl,drive-strength = <MXS_DRIVE_8mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm3_pins_a>;
+	status = "okay";
+};
+
+&reg_usb_5v {
+	gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+};
+
+&saif0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif0_pins_a>;
+	#sound-dai-cells = <0>;
+	assigned-clocks = <&clks 53>;
+	assigned-clock-rates = <12000000>;
+	status = "okay";
+};
+
+&saif1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif1_pins_a>;
+	#sound-dai-cells = <0>;
+	fsl,saif-master = <&saif0>;
+	status = "okay";
+};
+
+&ssp1 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&ssp1_sdio_pins_a>;
+	bus-width = <4>;
+	no-1-8-v;       /* force 3.3V VIO */
+	non-removable;
+	vmmc-supply = <&reg_3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	keep-power-in-suspend;
+	status = "okay";
+
+	wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+&ssp2 {
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-cfa10036.dts b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10036.dts
new file mode 100644
index 000000000000..f170df37b3f8
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10036.dts
@@ -0,0 +1,131 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 Free Electrons
+ */
+
+/dts-v1/;
+#include "imx28.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Crystalfontz CFA-10036 Board";
+	compatible = "crystalfontz,cfa10036", "fsl,imx28";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins_cfa10036>;
+
+		power {
+			gpios = <&gpio3 4 1>;
+			default-state = "on";
+		};
+	};
+
+	reg_vddio_sd0: vddio-sd0 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&mmc_pwr_cfa10036>;
+		regulator-name = "vddio-sd0";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 28 0>;
+	};
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_b>;
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_b>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	ssd1306: oled@3c {
+		compatible = "solomon,ssd1306fb-i2c";
+		pinctrl-names = "default";
+		pinctrl-0 = <&ssd1306_cfa10036>;
+		reg = <0x3c>;
+		reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
+		solomon,height = <32>;
+		solomon,width = <128>;
+		solomon,page-offset = <0>;
+		solomon,com-lrremap;
+		solomon,com-invdir;
+		solomon,com-offset = <32>;
+	};
+};
+
+&pinctrl {
+	ssd1306_cfa10036: ssd1306-10036@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP0_DATA7__GPIO_2_7
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	led_pins_cfa10036: leds-10036@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_AUART1_RX__GPIO_3_4
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	usb0_otg_cfa10036: otg-10036@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_RDY0__USB0_ID
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	mmc_pwr_cfa10036: mmc_pwr_cfa10036@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			0x31c3 /*
+			MX28_PAD_PWM3__GPIO_3_28 */
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_4bit_pins_a
+		&mmc0_cd_cfg &mmc0_sck_cfg>;
+	vmmc-supply = <&reg_vddio_sd0>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&usb0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_otg_cfa10036>;
+	dr_mode = "peripheral";
+	phy_type = "utmi";
+	status = "okay";
+};
+
+&usbphy0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-cfa10037.dts b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10037.dts
index d3e9a731525b..fd177daa6385 100644
--- a/arch/arm/boot/dts/imx28-cfa10037.dts
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10037.dts
@@ -14,7 +14,7 @@
 	compatible = "crystalfontz,cfa10037", "crystalfontz,cfa10036", "fsl,imx28";
 
 	apb@80000000 {
-		apbh@80000000 {
+		apbh-bus@80000000 {
 			pinctrl@80018000 {
 				usb_pins_cfa10037: usb-10037@0 {
 					reg = <0>;
@@ -38,7 +38,7 @@
 			};
 		};
 
-		apbx@80040000 {
+		apbx-bus@80040000 {
 			usbphy1: usbphy@8007e000 {
 				status = "okay";
 			};
@@ -64,20 +64,13 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_usb1_vbus: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&usb_pins_cfa10037>;
-			regulator-name = "usb1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio0 7 1>;
-		};
+	reg_usb1_vbus: regulator-0 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_pins_cfa10037>;
+		regulator-name = "usb1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio0 7 1>;
 	};
 };
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-cfa10049.dts b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10049.dts
new file mode 100644
index 000000000000..f0ce897b9d5c
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10049.dts
@@ -0,0 +1,411 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 Free Electrons
+ */
+
+/*
+ * The CFA-10049 is an expansion board for the CFA-10036 module, thus we
+ * need to include the CFA-10036 DTS.
+ */
+#include "imx28-cfa10036.dts"
+
+/ {
+	model = "Crystalfontz CFA-10049 Board";
+	compatible = "crystalfontz,cfa10049", "crystalfontz,cfa10036", "fsl,imx28";
+
+	i2cmux {
+		compatible = "i2c-mux-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2cmux_pins_cfa10049>;
+		mux-gpios = <&gpio1 22 0 &gpio1 23 0>;
+		i2c-parent = <&i2c1>;
+
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			adc0: nau7802@2a {
+				compatible = "nuvoton,nau7802";
+				reg = <0x2a>;
+				nuvoton,vldo = <3000>;
+			};
+		};
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			adc1: nau7802@2a {
+				compatible = "nuvoton,nau7802";
+				reg = <0x2a>;
+				nuvoton,vldo = <3000>;
+			};
+		};
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+				adc2: nau7802@2a {
+				compatible = "nuvoton,nau7802";
+				reg = <0x2a>;
+				nuvoton,vldo = <3000>;
+			};
+		};
+
+		i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			pca9555: pca9555@20 {
+				compatible = "nxp,pca9555";
+				pinctrl-names = "default";
+				pinctrl-0 = <&pca_pins_cfa10049>;
+				interrupt-parent = <&gpio2>;
+				interrupts = <19 0x2>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				reg = <0x20>;
+			};
+		};
+	};
+
+	reg_usb1_vbus: regulator-0 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_pins_cfa10049>;
+		regulator-name = "usb1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio0 7 1>;
+	};
+
+	spi-2 {
+		compatible = "spi-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi2_pins_cfa10049>;
+		status = "okay";
+		sck-gpios = <&gpio2 16 0>;
+		mosi-gpios = <&gpio2 17 0>;
+		miso-gpios = <&gpio2 18 0>;
+		cs-gpios = <&gpio3 5 0>;
+		num-chipselects = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hx8357: hx8357@0 {
+			compatible = "himax,hx8357b", "himax,hx8357";
+			reg = <0>;
+			spi-max-frequency = <100000>;
+			spi-cpol;
+			spi-cpha;
+			gpios-reset = <&gpio3 30 0>;
+			im-gpios = <&gpio5 4 0 &gpio5 5 0 &gpio5 6 0>;
+		};
+	};
+
+	spi-3 {
+		compatible = "spi-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi3_pins_cfa10049>;
+		status = "okay";
+		sck-gpios = <&gpio0 24 0>;
+		mosi-gpios = <&gpio0 28 0>;
+		cs-gpios = <&gpio0 17 0 &gpio0 26 0 &gpio0 27 0>;
+		num-chipselects = <3>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio5: gpio5@0 {
+			compatible = "fairchild,74hc595";
+			gpio-controller;
+			#gpio-cells = <2>;
+			reg = <0>;
+			registers-number = <2>;
+			spi-max-frequency = <100000>;
+		};
+
+		gpio6: gpio6@1 {
+			compatible = "fairchild,74hc595";
+			gpio-controller;
+			#gpio-cells = <2>;
+			reg = <1>;
+			registers-number = <4>;
+			spi-max-frequency = <100000>;
+		};
+
+		dac0: dh2228@2 {
+			compatible = "rohm,dh2228fv";
+			reg = <2>;
+			spi-max-frequency = <100000>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&rotary_btn_pins_cfa10049>;
+
+		rotary-button {
+			label = "rotary_button";
+			gpios = <&gpio3 26 1>;
+			debounce-interval = <10>;
+			linux,code = <28>;
+		};
+	};
+
+	rotary {
+		compatible = "rotary-encoder";
+		pinctrl-names = "default";
+		pinctrl-0 = <&rotary_pins_cfa10049>;
+		gpios = <&gpio3 24 1>, <&gpio3 25 1>;
+		linux,axis = <1>; /* REL_Y */
+		rotary-encoder,relative-axis;
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 3 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+
+	};
+
+	onewire {
+		compatible = "w1-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&w1_gpio_pins>;
+		status = "okay";
+		gpios = <&gpio1 21 0>;
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_a>;
+	status = "okay";
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_18bit_pins_cfa10049
+		     &lcdif_pins_cfa10049
+		     &lcdif_pins_cfa10049_pullup>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <32>;
+		bus-width = <18>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <9216000>;
+				hactive = <320>;
+				vactive = <480>;
+				hback-porch = <2>;
+				hfront-porch = <2>;
+				vback-porch = <2>;
+				vfront-porch = <2>;
+				hsync-len = <15>;
+				vsync-len = <15>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <1>;
+			};
+		};
+	};
+};
+
+&lradc {
+	fsl,lradc-touchscreen-wires = <4>;
+	status = "okay";
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a
+		&mac0_pins_cfa10049>;
+	phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <100>;
+	status = "okay";
+};
+
+&pinctrl {
+	usb_pins_cfa10049: usb-10049@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_D07__GPIO_0_7
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	i2cmux_pins_cfa10049: i2cmux-10049@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_D22__GPIO_1_22
+			MX28_PAD_LCD_D23__GPIO_1_23
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	mac0_pins_cfa10049: mac0-10049@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP2_SS2__GPIO_2_21
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	pca_pins_cfa10049: pca-10049@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP2_SS0__GPIO_2_19
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	rotary_pins_cfa10049: rotary-10049@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_I2C0_SCL__GPIO_3_24
+			MX28_PAD_I2C0_SDA__GPIO_3_25
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	rotary_btn_pins_cfa10049: rotary-btn-10049@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SAIF1_SDATA0__GPIO_3_26
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	spi2_pins_cfa10049: spi2-cfa10049@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP2_SCK__GPIO_2_16
+			MX28_PAD_SSP2_MOSI__GPIO_2_17
+			MX28_PAD_SSP2_MISO__GPIO_2_18
+			MX28_PAD_AUART1_TX__GPIO_3_5
+		>;
+		fsl,drive-strength = <MXS_DRIVE_8mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	spi3_pins_cfa10049: spi3-cfa10049@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_RDN__GPIO_0_24
+			MX28_PAD_GPMI_RESETN__GPIO_0_28
+			MX28_PAD_GPMI_CE1N__GPIO_0_17
+			MX28_PAD_GPMI_ALE__GPIO_0_26
+			MX28_PAD_GPMI_CLE__GPIO_0_27
+		>;
+		fsl,drive-strength = <MXS_DRIVE_8mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	lcdif_18bit_pins_cfa10049: lcdif-18bit@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_D00__LCD_D0
+			MX28_PAD_LCD_D01__LCD_D1
+			MX28_PAD_LCD_D02__LCD_D2
+			MX28_PAD_LCD_D03__LCD_D3
+			MX28_PAD_LCD_D04__LCD_D4
+			MX28_PAD_LCD_D05__LCD_D5
+			MX28_PAD_LCD_D06__LCD_D6
+			MX28_PAD_LCD_D07__LCD_D7
+			MX28_PAD_LCD_D08__LCD_D8
+			MX28_PAD_LCD_D09__LCD_D9
+			MX28_PAD_LCD_D10__LCD_D10
+			MX28_PAD_LCD_D11__LCD_D11
+			MX28_PAD_LCD_D12__LCD_D12
+			MX28_PAD_LCD_D13__LCD_D13
+			MX28_PAD_LCD_D14__LCD_D14
+			MX28_PAD_LCD_D15__LCD_D15
+			MX28_PAD_LCD_D16__LCD_D16
+			MX28_PAD_LCD_D17__LCD_D17
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_cfa10049: lcdif-evk@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RD_E__LCD_VSYNC
+			MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+			MX28_PAD_LCD_RS__LCD_DOTCLK
+			MX28_PAD_LCD_CS__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_cfa10049_pullup: lcdif-10049-pullup@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RESET__GPIO_3_30
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	w1_gpio_pins: w1-gpio@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_D21__GPIO_1_21
+		>;
+		fsl,drive-strength = <MXS_DRIVE_8mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>; /* 0 will enable the keeper */
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm3_pins_b>;
+	status = "okay";
+};
+
+&usb1 {
+	vbus-supply = <&reg_usb1_vbus>;
+	pinctrl-0 = <&usb1_pins_a>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usbphy1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-cfa10055.dts b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10055.dts
new file mode 100644
index 000000000000..cb68edd6101b
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10055.dts
@@ -0,0 +1,155 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Crystalfontz America, Inc.
+ * 				  Free Electrons
+ */
+
+/*
+ * The CFA-10055 is an expansion board for the CFA-10036 module and
+ * CFA-10037, thus we need to include the CFA-10037 DTS.
+ */
+#include "imx28-cfa10037.dts"
+
+/ {
+	model = "Crystalfontz CFA-10055 Board";
+	compatible = "crystalfontz,cfa10055", "crystalfontz,cfa10037", "crystalfontz,cfa10036", "fsl,imx28";
+
+	spi-2 {
+		compatible = "spi-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi2_pins_cfa10055>;
+		status = "okay";
+		sck-gpios = <&gpio2 16 0>;
+		mosi-gpios = <&gpio2 17 0>;
+		miso-gpios = <&gpio2 18 0>;
+		cs-gpios = <&gpio3 5 0>;
+		num-chipselects = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hx8357: hx8357@0 {
+			compatible = "himax,hx8357b", "himax,hx8357";
+			reg = <0>;
+			spi-max-frequency = <100000>;
+			spi-cpol;
+			spi-cpha;
+			gpios-reset = <&gpio3 30 0>;
+		};
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 3 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+	};
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_18bit_pins_cfa10055
+		     &lcdif_pins_cfa10055
+		     &lcdif_pins_cfa10055_pullup>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <32>;
+		bus-width = <18>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <9216000>;
+				hactive = <320>;
+				vactive = <480>;
+				hback-porch = <2>;
+				hfront-porch = <2>;
+				vback-porch = <2>;
+				vfront-porch = <2>;
+				hsync-len = <15>;
+				vsync-len = <15>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <1>;
+			};
+		};
+	};
+};
+
+&lradc {
+	fsl,lradc-touchscreen-wires = <4>;
+	status = "okay";
+};
+
+&pinctrl {
+	spi2_pins_cfa10055: spi2-cfa10055@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP2_SCK__GPIO_2_16
+			MX28_PAD_SSP2_MOSI__GPIO_2_17
+			MX28_PAD_SSP2_MISO__GPIO_2_18
+			MX28_PAD_AUART1_TX__GPIO_3_5
+		>;
+		fsl,drive-strength = <MXS_DRIVE_8mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	lcdif_18bit_pins_cfa10055: lcdif-18bit@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_D00__LCD_D0
+			MX28_PAD_LCD_D01__LCD_D1
+			MX28_PAD_LCD_D02__LCD_D2
+			MX28_PAD_LCD_D03__LCD_D3
+			MX28_PAD_LCD_D04__LCD_D4
+			MX28_PAD_LCD_D05__LCD_D5
+			MX28_PAD_LCD_D06__LCD_D6
+			MX28_PAD_LCD_D07__LCD_D7
+			MX28_PAD_LCD_D08__LCD_D8
+			MX28_PAD_LCD_D09__LCD_D9
+			MX28_PAD_LCD_D10__LCD_D10
+			MX28_PAD_LCD_D11__LCD_D11
+			MX28_PAD_LCD_D12__LCD_D12
+			MX28_PAD_LCD_D13__LCD_D13
+			MX28_PAD_LCD_D14__LCD_D14
+			MX28_PAD_LCD_D15__LCD_D15
+			MX28_PAD_LCD_D16__LCD_D16
+			MX28_PAD_LCD_D17__LCD_D17
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_cfa10055: lcdif-evk@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RD_E__LCD_VSYNC
+			MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+			MX28_PAD_LCD_RS__LCD_DOTCLK
+			MX28_PAD_LCD_CS__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_cfa10055_pullup: lcdif-10055-pullup@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RESET__GPIO_3_30
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm3_pins_b>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-cfa10056.dts b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10056.dts
new file mode 100644
index 000000000000..bc2d6fcad12f
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10056.dts
@@ -0,0 +1,109 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Free Electrons
+ */
+
+/*
+ * The CFA-10055 is an expansion board for the CFA-10036 module and
+ * CFA-10037, thus we need to include the CFA-10037 DTS.
+ */
+#include "imx28-cfa10037.dts"
+
+/ {
+	model = "Crystalfontz CFA-10056 Board";
+	compatible = "crystalfontz,cfa10056", "crystalfontz,cfa10037", "crystalfontz,cfa10036", "fsl,imx28";
+
+	spi-2 {
+		compatible = "spi-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi2_pins_cfa10056>;
+		status = "okay";
+		sck-gpios = <&gpio2 16 0>;
+		mosi-gpios = <&gpio2 17 0>;
+		miso-gpios = <&gpio2 18 0>;
+		cs-gpios = <&gpio3 5 0>;
+		num-chipselects = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hx8369: hx8369@0 {
+			compatible = "himax,hx8369a", "himax,hx8369";
+			reg = <0>;
+			spi-max-frequency = <100000>;
+			spi-cpol;
+			spi-cpha;
+			gpios-reset = <&gpio3 30 0>;
+		};
+	};
+};
+
+&pinctrl {
+	spi2_pins_cfa10056: spi2-cfa10056@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP2_SCK__GPIO_2_16
+			MX28_PAD_SSP2_MOSI__GPIO_2_17
+			MX28_PAD_SSP2_MISO__GPIO_2_18
+			MX28_PAD_AUART1_TX__GPIO_3_5
+		>;
+		fsl,drive-strength = <MXS_DRIVE_8mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	lcdif_pins_cfa10056: lcdif-10056@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RD_E__LCD_VSYNC
+			MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+			MX28_PAD_LCD_RS__LCD_DOTCLK
+			MX28_PAD_LCD_CS__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_cfa10056_pullup: lcdif-10056-pullup@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RESET__GPIO_3_30
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_24bit_pins_a
+			&lcdif_pins_cfa10056
+			&lcdif_pins_cfa10056_pullup >;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <32>;
+		bus-width = <24>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <32000000>;
+				hactive = <480>;
+				vactive = <800>;
+				hback-porch = <2>;
+				hfront-porch = <2>;
+				vback-porch = <2>;
+				vfront-porch = <2>;
+				hsync-len = <5>;
+				vsync-len = <5>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <1>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-cfa10057.dts b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10057.dts
new file mode 100644
index 000000000000..5875c3d7ba97
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10057.dts
@@ -0,0 +1,154 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Crystalfontz America, Inc.
+ * Copyright 2012 Free Electrons
+ */
+
+/*
+ * The CFA-10057 is an expansion board for the CFA-10036 module, thus we
+ * need to include the CFA-10036 DTS.
+ */
+#include "imx28-cfa10036.dts"
+
+/ {
+	model = "Crystalfontz CFA-10057 Board";
+	compatible = "crystalfontz,cfa10057", "crystalfontz,cfa10036", "fsl,imx28";
+
+	reg_usb1_vbus: regulator-0 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_pins_cfa10057>;
+		regulator-name = "usb1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio0 7 1>;
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 4 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <7>;
+	};
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_18bit_pins_cfa10057
+		     &lcdif_pins_cfa10057>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <32>;
+		bus-width = <18>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <30000000>;
+				hactive = <480>;
+				vactive = <800>;
+				hfront-porch = <12>;
+				hback-porch = <2>;
+				vfront-porch = <5>;
+				vback-porch = <3>;
+				hsync-len = <2>;
+				vsync-len = <2>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <1>;
+			};
+		};
+	};
+};
+
+&lradc {
+	fsl,lradc-touchscreen-wires = <4>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_a>;
+	status = "okay";
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>;
+	phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <100>;
+	status = "okay";
+};
+
+&pinctrl {
+	usb_pins_cfa10057: usb-10057@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_D07__GPIO_0_7
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_18bit_pins_cfa10057: lcdif-18bit@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_D00__LCD_D0
+			MX28_PAD_LCD_D01__LCD_D1
+			MX28_PAD_LCD_D02__LCD_D2
+			MX28_PAD_LCD_D03__LCD_D3
+			MX28_PAD_LCD_D04__LCD_D4
+			MX28_PAD_LCD_D05__LCD_D5
+			MX28_PAD_LCD_D06__LCD_D6
+			MX28_PAD_LCD_D07__LCD_D7
+			MX28_PAD_LCD_D08__LCD_D8
+			MX28_PAD_LCD_D09__LCD_D9
+			MX28_PAD_LCD_D10__LCD_D10
+			MX28_PAD_LCD_D11__LCD_D11
+			MX28_PAD_LCD_D12__LCD_D12
+			MX28_PAD_LCD_D13__LCD_D13
+			MX28_PAD_LCD_D14__LCD_D14
+			MX28_PAD_LCD_D15__LCD_D15
+			MX28_PAD_LCD_D16__LCD_D16
+			MX28_PAD_LCD_D17__LCD_D17
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_cfa10057: lcdif-evk@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RD_E__LCD_VSYNC
+			MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+			MX28_PAD_LCD_RS__LCD_DOTCLK
+			MX28_PAD_LCD_CS__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm4_pins_a>;
+	status = "okay";
+};
+
+&usb1 {
+	vbus-supply = <&reg_usb1_vbus>;
+	pinctrl-0 = <&usb1_pins_a>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usbphy1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-cfa10058.dts b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10058.dts
new file mode 100644
index 000000000000..b414e67ef379
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-cfa10058.dts
@@ -0,0 +1,121 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2013 Crystalfontz America, Inc.
+ * Copyright 2013 Free Electrons
+ */
+
+/*
+ * The CFA-10058 is an expansion board for the CFA-10036 module, thus we
+ * need to include the CFA-10036 DTS.
+ */
+#include "imx28-cfa10036.dts"
+
+/ {
+	model = "Crystalfontz CFA-10058 Board";
+	compatible = "crystalfontz,cfa10058", "crystalfontz,cfa10036", "fsl,imx28";
+
+	reg_usb1_vbus: regulator-0 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_pins_cfa10058>;
+		regulator-name = "usb1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio0 7 1>;
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 3 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+	};
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_24bit_pins_a
+			 &lcdif_pins_cfa10058>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <32>;
+		bus-width = <24>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <30000000>;
+				hactive = <800>;
+				vactive = <480>;
+				hback-porch = <40>;
+				hfront-porch = <40>;
+				vback-porch = <13>;
+				vfront-porch = <29>;
+				hsync-len = <8>;
+				vsync-len = <8>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <1>;
+			};
+		};
+	};
+};
+
+&lradc {
+	fsl,lradc-touchscreen-wires = <4>;
+	status = "okay";
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>;
+	phy-reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <100>;
+	status = "okay";
+};
+
+&pinctrl {
+	usb_pins_cfa10058: usb-10058@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_D07__GPIO_0_7
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_cfa10058: lcdif-10058@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RD_E__LCD_VSYNC
+			MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+			MX28_PAD_LCD_RS__LCD_DOTCLK
+			MX28_PAD_LCD_CS__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm3_pins_b>;
+	status = "okay";
+};
+
+&usb1 {
+	vbus-supply = <&reg_usb1_vbus>;
+	pinctrl-0 = <&usb1_pins_a>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usbphy1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-duckbill-2-485.dts b/arch/arm/boot/dts/nxp/mxs/imx28-duckbill-2-485.dts
new file mode 100644
index 000000000000..b73020ff1053
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-duckbill-2-485.dts
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
+ * Copyright (C) 2016 Michael Heimpold <mhei@heimpold.de>
+ */
+
+/dts-v1/;
+#include "imx28-duckbill-2.dts"
+
+/ {
+	model = "I2SE Duckbill 2 485";
+	compatible = "i2se,duckbill-2-485", "i2se,duckbill-2", "fsl,imx28";
+
+	leds {
+		rs485-red {
+			label = "duckbill:red:rs485";
+			gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
+		};
+
+		rs485-green {
+			label = "duckbill:green:rs485";
+			gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&i2c0 {
+	status = "disabled";
+};
+
+&led_pins {
+	fsl,pinmux-ids = <
+		MX28_PAD_SAIF0_MCLK__GPIO_3_20
+		MX28_PAD_SAIF0_LRCLK__GPIO_3_21
+		MX28_PAD_I2C0_SCL__GPIO_3_24
+		MX28_PAD_I2C0_SDA__GPIO_3_25
+	>;
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-duckbill-2-enocean.dts b/arch/arm/boot/dts/nxp/mxs/imx28-duckbill-2-enocean.dts
new file mode 100644
index 000000000000..473d99b9b42f
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-duckbill-2-enocean.dts
@@ -0,0 +1,69 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
+ * Copyright (C) 2016 Michael Heimpold <mhei@heimpold.de>
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include "imx28-duckbill-2.dts"
+
+/ {
+	model = "I2SE Duckbill 2 EnOcean";
+	compatible = "i2se,duckbill-2-enocean", "i2se,duckbill-2", "fsl,imx28";
+
+	leds {
+		enocean-blue {
+			label = "duckbill:blue:enocean";
+			gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
+		};
+
+		enocean-red {
+			label = "duckbill:red:enocean";
+			gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
+		};
+
+		enocean-green {
+			label = "duckbill:green:enocean";
+			gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&enocean_button>;
+
+		key-enocean {
+			label = "EnOcean";
+			linux,code = <KEY_NEW>;
+			gpios = <&gpio3 3 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&i2c0 {
+	status = "disabled";
+};
+
+&led_pins {
+	fsl,pinmux-ids = <
+		MX28_PAD_SAIF0_MCLK__GPIO_3_20
+		MX28_PAD_SAIF0_LRCLK__GPIO_3_21
+		MX28_PAD_AUART0_CTS__GPIO_3_2
+		MX28_PAD_I2C0_SCL__GPIO_3_24
+		MX28_PAD_I2C0_SDA__GPIO_3_25
+	>;
+};
+
+&pinctrl {
+	enocean_button: enocean-button@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_AUART0_RTS__GPIO_3_3
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-duckbill-2-spi.dts b/arch/arm/boot/dts/nxp/mxs/imx28-duckbill-2-spi.dts
new file mode 100644
index 000000000000..859d97a5a775
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-duckbill-2-spi.dts
@@ -0,0 +1,63 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
+ * Copyright (C) 2016 Michael Heimpold <mhei@heimpold.de>
+ */
+
+/dts-v1/;
+#include "imx28-duckbill-2.dts"
+
+/ {
+	model = "I2SE Duckbill 2 SPI";
+	compatible = "i2se,duckbill-2-spi", "i2se,duckbill-2", "fsl,imx28";
+
+	aliases {
+		ethernet1 = &qca7000;
+	};
+};
+
+&auart0 {
+	status = "disabled";
+};
+
+&i2c0 {
+	status = "disabled";
+};
+
+&pinctrl {
+	qca7000_pins: qca7000@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_AUART0_RTS__GPIO_3_3    /* Interrupt */
+			MX28_PAD_LCD_D13__GPIO_1_13      /* QCA7K reset */
+			MX28_PAD_LCD_D14__GPIO_1_14      /* GPIO 0 */
+			MX28_PAD_LCD_D15__GPIO_1_15      /* GPIO 1 */
+			MX28_PAD_LCD_D18__GPIO_1_18      /* GPIO 2 */
+			MX28_PAD_LCD_D21__GPIO_1_21      /* GPIO 3 */
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&ssp2 {
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	/delete-property/ bus-width;
+	/delete-property/ vmmc-supply;
+	status = "okay";
+
+	qca7000: ethernet@0 {
+		reg = <0>;
+		compatible = "qca,qca7000";
+		pinctrl-names = "default";
+		pinctrl-0 = <&qca7000_pins>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <3 IRQ_TYPE_EDGE_RISING>;
+		spi-cpha;
+		spi-cpol;
+		spi-max-frequency = <8000000>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-duckbill-2.dts b/arch/arm/boot/dts/nxp/mxs/imx28-duckbill-2.dts
new file mode 100644
index 000000000000..4e28212e9626
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-duckbill-2.dts
@@ -0,0 +1,170 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
+ * Copyright (C) 2016 Michael Heimpold <mhei@heimpold.de>
+ */
+
+/dts-v1/;
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "imx28.dtsi"
+
+/ {
+	model = "I2SE Duckbill 2";
+	compatible = "i2se,duckbill-2", "fsl,imx28";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x08000000>;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins>;
+
+		status-red {
+			label = "duckbill:red:status";
+			gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		status-green {
+			label = "duckbill:green:status";
+			gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_2pins_a>;
+	status = "okay";
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_a>;
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+};
+
+&lradc {
+	status = "okay";
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
+	phy-supply = <&reg_3p3v>;
+	phy-reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <25>;
+	phy-handle = <&ethphy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mac0_phy_int_pin>;
+			interrupt-parent = <&gpio0>;
+			interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+			max-speed = <100>;
+		};
+	};
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a>;
+
+	hog_pins_a: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_D17__GPIO_1_17    /* Revision detection */
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	mac0_phy_reset_pin: mac0-phy-reset@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_ALE__GPIO_0_26    /* PHY Reset */
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	mac0_phy_int_pin: mac0-phy-int@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_D07__GPIO_0_7    /* PHY Interrupt */
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	led_pins: leds@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SAIF0_MCLK__GPIO_3_20
+			MX28_PAD_SAIF0_LRCLK__GPIO_3_21
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_8bit_pins_a
+		&mmc0_cd_cfg &mmc0_sck_cfg>;
+	bus-width = <8>;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+	non-removable;
+};
+
+&ssp2 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_4bit_pins_b
+		&mmc2_cd_cfg &mmc2_sck_cfg_b>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "peripheral";
+};
+
+&usbphy0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-duckbill.dts b/arch/arm/boot/dts/nxp/mxs/imx28-duckbill.dts
new file mode 100644
index 000000000000..13ffd533fdea
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-duckbill.dts
@@ -0,0 +1,139 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2013-2014,2016 Michael Heimpold <mhei@heimpold.de>
+ * Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include "imx28.dtsi"
+
+/ {
+	model = "I2SE Duckbill";
+	compatible = "i2se,duckbill", "fsl,imx28";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x08000000>;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins>;
+
+		status-red {
+			label = "duckbill:red:status";
+			gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		status-green {
+			label = "duckbill:green:status";
+			gpios = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_2pins_a>;
+	status = "okay";
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_a>;
+	status = "okay";
+};
+
+&lradc {
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
+	phy-supply = <&reg_3p3v>;
+	phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <25>;
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a>;
+
+	hog_pins_a: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_D17__GPIO_1_17    /* Revision detection */
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	mac0_phy_reset_pin: mac0-phy-reset@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP0_DATA7__GPIO_2_7    /* PHY Reset */
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	led_pins: leds@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_AUART1_RX__GPIO_3_4
+			MX28_PAD_AUART1_TX__GPIO_3_5
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_4bit_pins_a
+		&mmc0_cd_cfg &mmc0_sck_cfg>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+};
+
+&ssp2 {
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "okay";
+};
+
+&usb0 {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-eukrea-mbmx283lc.dts b/arch/arm/boot/dts/nxp/mxs/imx28-eukrea-mbmx283lc.dts
index 29f8a3a245d4..7ae2d4ca8ef0 100644
--- a/arch/arm/boot/dts/imx28-eukrea-mbmx283lc.dts
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-eukrea-mbmx283lc.dts
@@ -47,7 +47,7 @@
 	status = "okay";
 };
 
-&pinctrl{
+&pinctrl {
 	pinctrl-names = "default";
 	pinctrl-0 = <&hog_pins_cpuimx283>;
 
diff --git a/arch/arm/boot/dts/imx28-eukrea-mbmx287lc.dts b/arch/arm/boot/dts/nxp/mxs/imx28-eukrea-mbmx287lc.dts
index cd875ace168d..cd875ace168d 100644
--- a/arch/arm/boot/dts/imx28-eukrea-mbmx287lc.dts
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-eukrea-mbmx287lc.dts
diff --git a/arch/arm/boot/dts/imx28-eukrea-mbmx28lc.dtsi b/arch/arm/boot/dts/nxp/mxs/imx28-eukrea-mbmx28lc.dtsi
index 3280fddaaf0d..652fc9e57a55 100644
--- a/arch/arm/boot/dts/imx28-eukrea-mbmx28lc.dtsi
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-eukrea-mbmx28lc.dtsi
@@ -14,17 +14,17 @@
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm 4 1000000>;
+		pwms = <&pwm 4 1000000 0>;
 		brightness-levels = <0 25 50 75 100 125 150 175 200 225 255>;
 		default-brightness-level = <10>;
 	};
 
-	button-sw3 {
+	gpio-keys-0 {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&gpio_button_sw3_pins_mbmx28lc>;
 
-		sw3 {
+		switch-sw3 {
 			label = "SW3";
 			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_MISC>;
@@ -32,12 +32,12 @@
 		};
 	};
 
-	button-sw4 {
+	gpio-keys-1 {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&gpio_button_sw4_pins_mbmx28lc>;
 
-		sw4 {
+		switch-sw4 {
 			label = "SW4";
 			gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_MISC>;
@@ -69,55 +69,45 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	reg_3p3v: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 
-		reg_lcd_3v3: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&reg_lcd_3v3_pins_mbmx28lc>;
-			regulator-name = "lcd-3v3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	reg_lcd_3v3: regulator-1 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&reg_lcd_3v3_pins_mbmx28lc>;
+		regulator-name = "lcd-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 
-		reg_usb0_vbus: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&reg_usb0_vbus_pins_mbmx28lc>;
-			regulator-name = "usb0_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio1 18 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	reg_usb0_vbus: regulator-2 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&reg_usb0_vbus_pins_mbmx28lc>;
+		regulator-name = "usb0_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 18 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 
-		reg_usb1_vbus: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&reg_usb1_vbus_pins_mbmx28lc>;
-			regulator-name = "usb1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio1 19 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-		};
+	reg_usb1_vbus: regulator-3 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&reg_usb1_vbus_pins_mbmx28lc>;
+		regulator-name = "usb1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
 	};
 
 	sound {
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-evk.dts b/arch/arm/boot/dts/nxp/mxs/imx28-evk.dts
new file mode 100644
index 000000000000..330d3aff6b6c
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-evk.dts
@@ -0,0 +1,352 @@
+// SPDX-License-Identifier: GPL-2.0+
+//
+// Copyright 2012 Freescale Semiconductor, Inc.
+
+/dts-v1/;
+#include "imx28.dtsi"
+
+/ {
+	model = "Freescale i.MX28 Evaluation Kit";
+	compatible = "fsl,imx28-evk", "fsl,imx28";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x08000000>;
+	};
+
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_vddio_sd0: regulator-vddio-sd0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vddio-sd0";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 28 0>;
+	};
+
+	reg_fec_3v3: regulator-fec-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "fec-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 15 0>;
+	};
+
+	reg_usb0_vbus: regulator-usb0-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb0_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 9 0>;
+		enable-active-high;
+	};
+
+	reg_usb1_vbus: regulator-usb1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 8 0>;
+		enable-active-high;
+	};
+
+	reg_lcd_3v3: regulator-lcd-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 30 0>;
+		enable-active-high;
+	};
+
+	reg_can_3v3: regulator-can-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "can-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 13 0>;
+		enable-active-high;
+	};
+
+	reg_lcd_5v: regulator-lcd-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	panel {
+		compatible = "sii,43wvf1g";
+		backlight = <&backlight_display>;
+		dvdd-supply = <&reg_lcd_3v3>;
+		avdd-supply = <&reg_lcd_5v>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
+	sound {
+		compatible = "fsl,imx28-evk-sgtl5000",
+			     "fsl,mxs-audio-sgtl5000";
+		model = "imx28-evk-sgtl5000";
+		saif-controllers = <&saif0 &saif1>;
+		audio-codec = <&sgtl5000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pin_gpio3_5>;
+
+		user {
+			label = "Heartbeat";
+			gpios = <&gpio3 5 0>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	backlight_display: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 2 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+	};
+};
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_pins_a>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&auart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart3_pins_a>;
+	status = "okay";
+};
+
+&can0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&can0_pins_a>;
+	xceiver-supply = <&reg_can_3v3>;
+	status = "okay";
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&can1_pins_a>;
+	xceiver-supply = <&reg_can_3v3>;
+	status = "okay";
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_a>;
+	status = "okay";
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg
+		     &gpmi_pins_evk>;
+	status = "okay";
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_24bit_pins_a
+		     &lcdif_pins_evk>;
+	status = "okay";
+
+	port {
+		display_out: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
+};
+
+&lradc {
+	fsl,lradc-touchscreen-wires = <4>;
+	fsl,ave-ctrl = <4>;
+	fsl,ave-delay = <2>;
+	fsl,settling = <10>;
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+
+	sgtl5000: codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		VDDA-supply = <&reg_3p3v>;
+		VDDIO-supply = <&reg_3p3v>;
+		clocks = <&saif0>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c32";
+		pagesize = <32>;
+		reg = <0x51>;
+	};
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>;
+	phy-supply = <&reg_fec_3v3>;
+	phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <100>;
+	status = "okay";
+};
+
+&mac1 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac1_pins_a>;
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a>;
+
+	hog_pins_a: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP1_CMD__GPIO_2_13
+			MX28_PAD_SSP1_DATA3__GPIO_2_15
+			MX28_PAD_ENET0_RX_CLK__GPIO_4_13
+			MX28_PAD_SSP1_SCK__GPIO_2_12
+			MX28_PAD_PWM3__GPIO_3_28
+			MX28_PAD_LCD_RESET__GPIO_3_30
+			MX28_PAD_AUART2_RX__GPIO_3_8
+			MX28_PAD_AUART2_TX__GPIO_3_9
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	led_pin_gpio3_5: led_gpio3_5@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_AUART1_TX__GPIO_3_5
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	gpmi_pins_evk: gpmi-nand-evk@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_CE1N__GPMI_CE1N
+			MX28_PAD_GPMI_RDY1__GPMI_READY1
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_evk: lcdif-evk@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RD_E__LCD_VSYNC
+			MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+			MX28_PAD_LCD_RS__LCD_DOTCLK
+			MX28_PAD_LCD_CS__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm2_pins_a>;
+	status = "okay";
+};
+
+&saif0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif0_pins_a>;
+	status = "okay";
+};
+
+&saif1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif1_pins_a>;
+	fsl,saif-master = <&saif0>;
+	status = "okay";
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_8bit_pins_a
+		&mmc0_cd_cfg &mmc0_sck_cfg>;
+	bus-width = <8>;
+	wp-gpios = <&gpio2 12 0>;
+	vmmc-supply = <&reg_vddio_sd0>;
+	status = "okay";
+};
+
+&ssp1 {
+	compatible = "fsl,imx28-mmc";
+	bus-width = <8>;
+	wp-gpios = <&gpio0 28 0>;
+};
+
+&ssp2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "okay";
+
+	flash: flash@0 {
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "sst,sst25vf016b", "jedec,spi-nor";
+		spi-max-frequency = <40000000>;
+	};
+};
+
+&usb0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_id_pins_a>;
+	vbus-supply = <&reg_usb0_vbus>;
+	status = "okay";
+};
+
+&usb1 {
+	vbus-supply = <&reg_usb1_vbus>;
+	status = "okay";
+};
+
+&usbphy0 {
+	status = "okay";
+};
+
+&usbphy1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-lwe.dtsi b/arch/arm/boot/dts/nxp/mxs/imx28-lwe.dtsi
index bb971e660db8..410dfe17f8ca 100644
--- a/arch/arm/boot/dts/imx28-lwe.dtsi
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-lwe.dtsi
@@ -18,6 +18,7 @@
 
 	memory@40000000 {
 		reg = <0x40000000 0x08000000>;
+		device_type = "memory";
 	};
 
 	reg_3v3: regulator-reg-3v3 {
@@ -54,23 +55,6 @@
 	status = "okay";
 };
 
-&saif0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&saif0_pins_a>;
-	#sound-dai-cells = <0>;
-	assigned-clocks = <&clks 53>;
-	assigned-clock-rates = <12000000>;
-	status = "okay";
-};
-
-&saif1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&saif1_pins_a>;
-	fsl,saif-master = <&saif0>;
-	#sound-dai-cells = <0>;
-	status = "okay";
-};
-
 &spi3_pins_a {
 	fsl,pinmux-ids = <
 		MX28_PAD_AUART2_RX__SSP3_D4
@@ -108,7 +92,7 @@
 
 	flash@0 {
 		compatible = "jedec,spi-nor";
-		spi-max-frequency = <40000000>;
+		spi-max-frequency = <20000000>;
 		reg = <0>;
 
 		partitions {
@@ -132,14 +116,21 @@
 				reg = <0x90000 0x10000>;
 			};
 
-			partition@100000 {
-				label = "kernel";
-				reg = <0x100000 0x400000>;
+			partition@a0000 {
+				label = "rescue";
+				reg = <0xa0000 0xf40000>;
+			};
+
+			partition@fe0000 {
+				/* 1st sector for SPL boot img source data */
+				label = "spl-boot-data1";
+				reg = <0xfe0000 0x10000>;
 			};
 
-			partition@500000 {
-				label = "swupdate";
-				reg = <0x500000 0x800000>;
+			partition@ff0000 {
+				/* 2nd sector for SPL boot img source data */
+				label = "spl-boot-data2";
+				reg = <0xff0000 0x10000>;
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-m28.dtsi b/arch/arm/boot/dts/nxp/mxs/imx28-m28.dtsi
new file mode 100644
index 000000000000..66facef10ba9
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-m28.dtsi
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2014 Marek Vasut <marex@denx.de>
+ */
+
+#include "imx28.dtsi"
+
+/ {
+	model = "Aries/DENX M28";
+	compatible = "aries,m28", "denx,m28", "fsl,imx28";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x08000000>;
+	};
+
+	reg_3p3v: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+};
+
+&gpmi {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+
+	rtc: rtc@68 {
+		compatible = "st,m41t62";
+		reg = <0x68>;
+	};
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-m28cu3.dts b/arch/arm/boot/dts/nxp/mxs/imx28-m28cu3.dts
new file mode 100644
index 000000000000..34b4d3246db1
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-m28cu3.dts
@@ -0,0 +1,248 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2013 Marek Vasut <marex@denx.de>
+ */
+
+/dts-v1/;
+#include "imx28.dtsi"
+
+/ {
+	model = "MSR M28CU3";
+	compatible = "msr,m28cu3", "fsl,imx28";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x08000000>;
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 3 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins_gpio>;
+
+		user1 {
+			label = "sd0-led";
+			gpios = <&gpio2 26 0>;
+			linux,default-trigger = "mmc0";
+		};
+
+		user2 {
+			label = "sd1-led";
+			gpios = <&gpio2 24 0>;
+			linux,default-trigger = "mmc2";
+		};
+	};
+
+	reg_3p3v: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_vddio_sd0: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "vddio-sd0";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 29 0>;
+	};
+
+	reg_vddio_sd1: regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vddio-sd1";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 19 0>;
+	};
+
+	reg_usb1_vbus: regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 8 0>;
+		enable-active-high;
+	};
+};
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_2pins_a>;
+	status = "okay";
+};
+
+&auart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart3_2pins_b>;
+	status = "okay";
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_b>;
+	status = "okay";
+};
+
+&gpmi {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
+	status = "okay";
+
+	partition@0 {
+		label = "gpmi-nfc-0-boot";
+		reg = <0x00000000 0x01400000>;
+		read-only;
+	};
+
+	partition@1 {
+		label = "gpmi-nfc-general-use";
+		reg = <0x01400000 0x0ec00000>;
+	};
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_24bit_pins_a
+		     &lcdif_pins_m28>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <32>;
+		bus-width = <24>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <6410256>;
+				hactive = <320>;
+				vactive = <240>;
+				hback-porch = <38>;
+				hfront-porch = <20>;
+				vback-porch = <15>;
+				vfront-porch = <5>;
+				hsync-len = <30>;
+				vsync-len = <3>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <1>;
+			};
+		};
+	};
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>;
+	phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <100>;
+	status = "okay";
+};
+
+&mac1 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac1_pins_a>;
+	status = "okay";
+};
+
+&ocotp {
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a>;
+
+	hog_pins_a: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP2_SS0__GPIO_2_19
+			MX28_PAD_PWM4__GPIO_3_29
+			MX28_PAD_AUART2_RX__GPIO_3_8
+			MX28_PAD_ENET0_RX_CLK__GPIO_4_13
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_m28: lcdif-m28@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_VSYNC__LCD_VSYNC
+			MX28_PAD_LCD_HSYNC__LCD_HSYNC
+			MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
+			MX28_PAD_LCD_RESET__LCD_RESET
+			MX28_PAD_LCD_CS__LCD_ENABLE
+			MX28_PAD_AUART1_TX__GPIO_3_5
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	led_pins_gpio: leds-m28@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP3_MISO__GPIO_2_26
+			MX28_PAD_SSP3_SCK__GPIO_2_24
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm3_pins_a>;
+	status = "okay";
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_4bit_pins_a
+		     &mmc0_cd_cfg
+		     &mmc0_sck_cfg>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_vddio_sd0>;
+	status = "okay";
+};
+
+&ssp2 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_4bit_pins_a
+		     &mmc2_cd_cfg
+		     &mmc2_sck_cfg_a>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_vddio_sd1>;
+	status = "okay";
+};
+
+&usb1 {
+	vbus-supply = <&reg_usb1_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb1_pins_a>;
+	disable-over-current;
+	status = "okay";
+};
+
+&usbphy1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-m28evk.dts b/arch/arm/boot/dts/nxp/mxs/imx28-m28evk.dts
new file mode 100644
index 000000000000..13070ca08cff
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-m28evk.dts
@@ -0,0 +1,258 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+
+ * Copyright (C) 2012 Marek Vasut <marex@denx.de>
+ */
+
+/dts-v1/;
+#include "imx28-m28.dtsi"
+
+/ {
+	model = "Aries/DENX M28EVK";
+	compatible = "aries,m28evk", "denx,m28evk", "fsl,imx28";
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 4 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+	};
+
+	reg_vddio_sd0: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "vddio-sd0";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 28 0>;
+	};
+
+	reg_usb0_vbus: regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb0_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 12 0>;
+	};
+
+	reg_usb1_vbus: regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 13 0>;
+	};
+
+	sound {
+		compatible = "denx,m28evk-sgtl5000",
+			     "fsl,mxs-audio-sgtl5000";
+		model = "m28evk-sgtl5000";
+		saif-controllers = <&saif0 &saif1>;
+		audio-codec = <&sgtl5000>;
+	};
+};
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_pins_a>;
+	status = "okay";
+};
+
+&auart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart1_pins_a>;
+	status = "okay";
+};
+
+&auart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart2_2pins_b>;
+	status = "okay";
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_a>;
+	status = "okay";
+};
+
+&i2c0 {
+	sgtl5000: codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		VDDA-supply = <&reg_3p3v>;
+		VDDIO-supply = <&reg_3p3v>;
+		clocks = <&saif0>;
+	};
+
+	eeprom: eeprom@51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+		pagesize = <32>;
+	};
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_24bit_pins_a
+		     &lcdif_pins_m28>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <16>;
+		bus-width = <18>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <33260000>;
+				hactive = <800>;
+				vactive = <480>;
+				hback-porch = <0>;
+				hfront-porch = <256>;
+				vback-porch = <0>;
+				vfront-porch = <45>;
+				hsync-len = <1>;
+				vsync-len = <1>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <1>;
+			};
+		};
+	};
+};
+
+&lradc {
+	status = "okay";
+	fsl,lradc-touchscreen-wires = <4>;
+};
+
+&can0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&can0_pins_a>;
+	status = "okay";
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&can1_pins_a>;
+	status = "okay";
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>;
+	clocks = <&clks 57>, <&clks 57>;
+	clock-names = "ipg", "ahb";
+	status = "okay";
+};
+
+&mac1 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac1_pins_a>;
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a>;
+
+	hog_pins_a: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_PWM3__GPIO_3_28
+			MX28_PAD_AUART2_CTS__GPIO_3_10
+			MX28_PAD_AUART2_RTS__GPIO_3_11
+			MX28_PAD_AUART3_RX__GPIO_3_12
+			MX28_PAD_AUART3_TX__GPIO_3_13
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_m28: lcdif-m28@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
+			MX28_PAD_LCD_ENABLE__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm4_pins_a>;
+	status = "okay";
+};
+
+&saif0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif0_pins_a>;
+	status = "okay";
+};
+
+&saif1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif1_pins_a>;
+	fsl,saif-master = <&saif0>;
+	status = "okay";
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_8bit_pins_a
+		     &mmc0_cd_cfg
+		     &mmc0_sck_cfg>;
+	bus-width = <8>;
+	wp-gpios = <&gpio3 10 0>;
+	vmmc-supply = <&reg_vddio_sd0>;
+	status = "okay";
+};
+
+&ssp2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "okay";
+
+	flash: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "m25p80", "jedec,spi-nor";
+		spi-max-frequency = <40000000>;
+		reg = <0>;
+	};
+};
+
+&usb0 {
+	vbus-supply = <&reg_usb0_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_pins_a>;
+	status = "okay";
+};
+
+&usb1 {
+	vbus-supply = <&reg_usb1_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb1_pins_a>;
+	status = "okay";
+};
+
+&usbphy0 {
+	status = "okay";
+};
+
+&usbphy1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-pinfunc.h b/arch/arm/boot/dts/nxp/mxs/imx28-pinfunc.h
index e11f69ba0fe4..d427e6c2fa78 100644
--- a/arch/arm/boot/dts/imx28-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-pinfunc.h
@@ -1,14 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Header providing constants for i.MX28 pinctrl bindings.
  *
  * Copyright (C) 2013 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
  */
 
 #ifndef __DT_BINDINGS_MX28_PINCTRL_H__
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-sps1.dts b/arch/arm/boot/dts/nxp/mxs/imx28-sps1.dts
new file mode 100644
index 000000000000..ca62e7933116
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-sps1.dts
@@ -0,0 +1,145 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2012 Marek Vasut <marex@denx.de>
+ */
+
+/dts-v1/;
+#include "imx28.dtsi"
+
+/ {
+	model = "SchulerControl GmbH, SC SPS 1";
+	compatible = "schulercontrol,imx28-sps1", "fsl,imx28";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x08000000>;
+	};
+
+	reg_usb0_vbus: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb0_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 9 0>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		status = "okay";
+
+		led-1 {
+			label = "sps1-1:yellow:user";
+			gpios = <&gpio0 6 0>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-2 {
+			label = "sps1-2:red:user";
+			gpios = <&gpio0 3 0>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-3 {
+			label = "sps1-3:red:user";
+			gpios = <&gpio0 0 0>;
+			linux,default-trigger = "heartbeat";
+		};
+
+	};
+};
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_pins_a>;
+	status = "okay";
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_a>;
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+
+	rtc: rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+
+	eeprom: eeprom@52 {
+		compatible = "atmel,24c64";
+		reg = <0x52>;
+		pagesize = <32>;
+	};
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>;
+	status = "okay";
+};
+
+&mac1 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac1_pins_a>;
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a>;
+
+	hog_pins_a: hog-gpios@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_D00__GPIO_0_0
+			MX28_PAD_GPMI_D03__GPIO_0_3
+			MX28_PAD_GPMI_D06__GPIO_0_6
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_4bit_pins_a>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&ssp2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx28-spi";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_a>;
+	status = "okay";
+
+	flash: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "everspin,mr25h256", "mr25h256";
+		spi-max-frequency = <40000000>;
+		reg = <0>;
+	};
+};
+
+&usb0 {
+	vbus-supply = <&reg_usb0_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_pins_b>;
+	status = "okay";
+};
+
+&usbphy0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/mxs/imx28-ts4600.dts b/arch/arm/boot/dts/nxp/mxs/imx28-ts4600.dts
new file mode 100644
index 000000000000..ae6ed5c41be3
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-ts4600.dts
@@ -0,0 +1,66 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2016 Savoir-Faire Linux
+ * Author: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
+ */
+
+/dts-v1/;
+#include "imx28.dtsi"
+#include "dt-bindings/gpio/gpio.h"
+
+/ {
+
+	model = "Technologic Systems i.MX28 TS-4600";
+	compatible = "technologic,imx28-ts4600", "fsl,imx28";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x10000000>;   /* 256MB */
+	};
+
+	reg_vddio_sd0: regulator-vddio-sd0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vddio-sd0";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		gpio = <&gpio3 28 GPIO_ACTIVE_LOW>;
+	};
+
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_a>;
+	status = "okay";
+};
+
+&pinctrl {
+	en_sd_pwr: en-sd-pwr@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_PWM3__GPIO_3_28
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm2_pins_a>;
+	status = "okay";
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_4bit_pins_a
+		     &mmc0_sck_cfg
+		     &en_sd_pwr>;
+	broken-cd;
+	bus-width = <4>;
+	vmmc-supply = <&reg_vddio_sd0>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-tx28.dts b/arch/arm/boot/dts/nxp/mxs/imx28-tx28.dts
index 6d7b044fec5b..9290635352f1 100644
--- a/arch/arm/boot/dts/imx28-tx28.dts
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-tx28.dts
@@ -1,43 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
 /*
  * Copyright 2012 Shawn Guo <shawn.guo@linaro.org>
  * Copyright 2013-2017 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 /dts-v1/;
@@ -167,7 +131,7 @@
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm 0 500000>;
+		pwms = <&pwm 0 500000 0>;
 		/*
 		 * a silly way to create a 1:1 relationship between the
 		 * PWM value and the actual duty cycle
@@ -221,16 +185,16 @@
 		linux,no-autorepeat;
 	};
 
-	spi_gpio: spi-gpio {
+	spi_gpio: spi {
 		compatible = "spi-gpio";
 		#address-cells = <1>;
 		#size-cells = <0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&tx28_spi_gpio_pins>;
 
-		gpio-sck = <&gpio2 24 GPIO_ACTIVE_HIGH>;
-		gpio-mosi = <&gpio2 25 GPIO_ACTIVE_HIGH>;
-		gpio-miso = <&gpio2 26 GPIO_ACTIVE_HIGH>;
+		sck-gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio2 25 GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
 		num-chipselects = <3>;
 		cs-gpios = <
 			&gpio2 27 GPIO_ACTIVE_LOW
@@ -296,6 +260,7 @@
 	sgtl5000: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_3p3v>;
 		clocks = <&mclk>;
@@ -358,7 +323,6 @@
 		display-timings {
 			native-mode = <&timing5>;
 			timing0: timing0 {
-				panel-name = "VGA";
 				clock-frequency = <25175000>;
 				hactive = <640>;
 				vactive = <480>;
@@ -375,7 +339,6 @@
 			};
 
 			timing1: timing1 {
-				panel-name = "ETV570";
 				clock-frequency = <25175000>;
 				hactive = <640>;
 				vactive = <480>;
@@ -392,7 +355,6 @@
 			};
 
 			timing2: timing2 {
-				panel-name = "ET0350";
 				clock-frequency = <6500000>;
 				hactive = <320>;
 				vactive = <240>;
@@ -409,7 +371,6 @@
 			};
 
 			timing3: timing3 {
-				panel-name = "ET0430";
 				clock-frequency = <9000000>;
 				hactive = <480>;
 				vactive = <272>;
@@ -426,7 +387,6 @@
 			};
 
 			timing4: timing4 {
-				panel-name = "ET0500", "ET0700";
 				clock-frequency = <33260000>;
 				hactive = <800>;
 				vactive = <480>;
@@ -443,7 +403,6 @@
 			};
 
 			timing5: timing5 {
-				panel-name = "ETQ570";
 				clock-frequency = <6400000>;
 				hactive = <320>;
 				vactive = <240>;
@@ -656,13 +615,13 @@
 &saif0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&saif0_pins_b>;
-	fsl,saif-master;
 	status = "okay";
 };
 
 &saif1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&saif1_pins_a>;
+	fsl,saif-master = <&saif0>;
 	status = "okay";
 };
 
@@ -688,6 +647,7 @@
 	vbus-supply = <&reg_usb0_vbus>;
 	disable-over-current;
 	dr_mode = "peripheral";
+	phy_type = "utmi";
 	status = "okay";
 };
 
@@ -695,19 +655,18 @@
 	vbus-supply = <&reg_usb1_vbus>;
 	disable-over-current;
 	dr_mode = "host";
+	phy_type = "utmi";
 	status = "okay";
 };
 
 &usbphy0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&tx28_usbphy0_pins>;
-	phy_type = "utmi";
 	status = "okay";
 };
 
 &usbphy1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&tx28_usbphy1_pins>;
-	phy_type = "utmi";
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx28-xea.dts b/arch/arm/boot/dts/nxp/mxs/imx28-xea.dts
index a400c108f66a..6c5e6856648a 100644
--- a/arch/arm/boot/dts/imx28-xea.dts
+++ b/arch/arm/boot/dts/nxp/mxs/imx28-xea.dts
@@ -8,6 +8,7 @@
 #include "imx28-lwe.dtsi"
 
 / {
+	model = "Liebherr XEA board";
 	compatible = "lwn,imx28-xea", "fsl,imx28";
 };
 
diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/nxp/mxs/imx28.dtsi
index 130b4145af82..ece46d0e7c7f 100644
--- a/arch/arm/boot/dts/imx28.dtsi
+++ b/arch/arm/boot/dts/nxp/mxs/imx28.dtsi
@@ -56,7 +56,7 @@
 		reg = <0x80000000 0x80000>;
 		ranges;
 
-		apbh@80000000 {
+		apbh-bus@80000000 {
 			compatible = "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -78,17 +78,13 @@
 				status = "disabled";
 			};
 
-			dma_apbh: dma-apbh@80004000 {
+			dma_apbh: dma-controller@80004000 {
 				compatible = "fsl,imx28-dma-apbh";
 				reg = <0x80004000 0x2000>;
-				interrupts = <82 83 84 85
-					      88 88 88 88
-					      88 88 88 88
-					      87 86 0 0>;
-				interrupt-names = "ssp0", "ssp1", "ssp2", "ssp3",
-						  "gpmi0", "gmpi1", "gpmi2", "gmpi3",
-						  "gpmi4", "gmpi5", "gpmi6", "gmpi7",
-						  "hsadc", "lcdif", "empty", "empty";
+				interrupts = <82>, <83>, <84>, <85>,
+					     <88>, <88>, <88>, <88>,
+					     <88>, <88>, <88>, <88>,
+					     <87>, <86>, <0>, <0>;
 				#dma-cells = <1>;
 				dma-channels = <16>;
 				clocks = <&clks 25>;
@@ -168,7 +164,7 @@
 				reg = <0x80018000 0x2000>;
 
 				gpio0: gpio@0 {
-					compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+					compatible = "fsl,imx28-gpio";
 					reg = <0>;
 					interrupts = <127>;
 					gpio-controller;
@@ -178,7 +174,7 @@
 				};
 
 				gpio1: gpio@1 {
-					compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+					compatible = "fsl,imx28-gpio";
 					reg = <1>;
 					interrupts = <126>;
 					gpio-controller;
@@ -188,7 +184,7 @@
 				};
 
 				gpio2: gpio@2 {
-					compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+					compatible = "fsl,imx28-gpio";
 					reg = <2>;
 					interrupts = <125>;
 					gpio-controller;
@@ -198,7 +194,7 @@
 				};
 
 				gpio3: gpio@3 {
-					compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+					compatible = "fsl,imx28-gpio";
 					reg = <3>;
 					interrupts = <124>;
 					gpio-controller;
@@ -208,7 +204,7 @@
 				};
 
 				gpio4: gpio@4 {
-					compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+					compatible = "fsl,imx28-gpio";
 					reg = <4>;
 					interrupts = <123>;
 					gpio-controller;
@@ -759,6 +755,16 @@
 					fsl,pull-up = <MXS_PULL_DISABLE>;
 				};
 
+				pwm7_pins_a: pwm7@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						MX28_PAD_SAIF1_SDATA0__PWM_7
+					>;
+					fsl,drive-strength = <MXS_DRIVE_4mA>;
+					fsl,voltage = <MXS_VOLTAGE_HIGH>;
+					fsl,pull-up = <MXS_PULL_DISABLE>;
+				};
+
 				lcdif_24bit_pins_a: lcdif-24bit@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
@@ -994,26 +1000,22 @@
 				status = "disabled";
 			};
 
-			dma_apbx: dma-apbx@80024000 {
+			dma_apbx: dma-controller@80024000 {
 				compatible = "fsl,imx28-dma-apbx";
 				reg = <0x80024000 0x2000>;
-				interrupts = <78 79 66 0
-					      80 81 68 69
-					      70 71 72 73
-					      74 75 76 77>;
-				interrupt-names = "auart4-rx", "auart4-tx", "spdif-tx", "empty",
-						  "saif0", "saif1", "i2c0", "i2c1",
-						  "auart0-rx", "auart0-tx", "auart1-rx", "auart1-tx",
-						  "auart2-rx", "auart2-tx", "auart3-rx", "auart3-tx";
+				interrupts = <78>, <79>, <66>, <0>,
+					     <80>, <81>, <68>, <69>,
+					     <70>, <71>, <72>, <73>,
+					     <74>, <75>, <76>, <77>;
 				#dma-cells = <1>;
 				dma-channels = <16>;
 				clocks = <&clks 26>;
 			};
 
 			dcp: crypto@80028000 {
-				compatible = "fsl,imx28-dcp", "fsl,imx23-dcp";
+				compatible = "fsl,imx28-dcp";
 				reg = <0x80028000 0x2000>;
-				interrupts = <52 53 54>;
+				interrupts = <52>, <53>, <54>;
 				status = "okay";
 			};
 
@@ -1100,7 +1102,7 @@
 			};
 		};
 
-		apbx@80040000 {
+		apbx-bus@80040000 {
 			compatible = "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -1108,7 +1110,7 @@
 			ranges;
 
 			clks: clkctrl@80040000 {
-				compatible = "fsl,imx28-clkctrl", "fsl,clkctrl";
+				compatible = "fsl,imx28-clkctrl";
 				reg = <0x80040000 0x2000>;
 				#clock-cells = <1>;
 			};
@@ -1144,8 +1146,8 @@
 			lradc: lradc@80050000 {
 				compatible = "fsl,imx28-lradc";
 				reg = <0x80050000 0x2000>;
-				interrupts = <10 14 15 16 17 18 19
-						20 21 22 23 24 25>;
+				interrupts = <10>, <14>, <15>, <16>, <17>, <18>, <19>,
+					     <20>, <21>, <22>, <23>, <24>, <25>;
 				status = "disabled";
 				clocks = <&clks 41>;
 				#io-channel-cells = <1>;
@@ -1193,7 +1195,7 @@
 				compatible = "fsl,imx28-pwm", "fsl,imx23-pwm";
 				reg = <0x80064000 0x2000>;
 				clocks = <&clks 44>;
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				fsl,pwm-number = <8>;
 				status = "disabled";
 			};
@@ -1201,7 +1203,7 @@
 			timer: timrot@80068000 {
 				compatible = "fsl,imx28-timrot", "fsl,timrot";
 				reg = <0x80068000 0x2000>;
-				interrupts = <48 49 50 51>;
+				interrupts = <48>, <49>, <50>, <51>;
 				clocks = <&clks 26>;
 			};
 
@@ -1260,7 +1262,7 @@
 				reg = <0x80074000 0x1000>;
 				interrupts = <47>;
 				clocks = <&clks 45>, <&clks 26>;
-				clock-names = "uart", "apb_pclk";
+				clock-names = "uartclk", "apb_pclk";
 				status = "disabled";
 			};
 
diff --git a/arch/arm/boot/dts/mxs-pinfunc.h b/arch/arm/boot/dts/nxp/mxs/mxs-pinfunc.h
index c6da987b20cb..31297abcbc71 100644
--- a/arch/arm/boot/dts/mxs-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/mxs/mxs-pinfunc.h
@@ -1,14 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Header providing constants for i.MX28 pinctrl bindings.
  *
  * Copyright (C) 2013 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
  */
 
 #ifndef __DT_BINDINGS_MXS_PINCTRL_H__
diff --git a/arch/arm/boot/dts/nxp/vf/Makefile b/arch/arm/boot/dts/nxp/vf/Makefile
new file mode 100644
index 000000000000..0a4a7f9dd43e
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/vf/Makefile
@@ -0,0 +1,16 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_SOC_VF610) += \
+	vf500-colibri-eval-v3.dtb \
+	vf610-bk4.dtb \
+	vf610-colibri-eval-v3.dtb \
+	vf610m4-colibri.dtb \
+	vf610-cosmic.dtb \
+	vf610m4-cosmic.dtb \
+	vf610-twr.dtb \
+	vf610-zii-cfu1.dtb \
+	vf610-zii-dev-rev-b.dtb \
+	vf610-zii-dev-rev-c.dtb \
+	vf610-zii-scu4-aib.dtb \
+	vf610-zii-spb4.dtb \
+	vf610-zii-ssmb-dtu.dtb \
+	vf610-zii-ssmb-spu3.dtb
diff --git a/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi b/arch/arm/boot/dts/nxp/vf/vf-colibri-eval-v3.dtsi
index 14c411f146f5..86c360868e4b 100644
--- a/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi
+++ b/arch/arm/boot/dts/nxp/vf/vf-colibri-eval-v3.dtsi
@@ -17,6 +17,7 @@
 	panel: panel {
 		compatible = "edt,et057090dhu";
 		backlight = <&bl>;
+		power-supply = <&reg_3v3>;
 
 		port {
 			panel_in: endpoint {
@@ -55,7 +56,7 @@
 	brightness-levels = <0 4 8 16 32 64 128 255>;
 	default-brightness-level = <6>;
 	power-supply = <&reg_3v3>;
-	status  = "okay";
+	status = "okay";
 };
 
 &dcu0 {
@@ -142,11 +143,9 @@
 };
 
 &iomuxc {
-	vf610-colibri {
-		pinctrl_can_int: can_int {
-			fsl,pins = <
-				VF610_PAD_PTB21__GPIO_43	0x22ed
-			>;
-		};
+	pinctrl_can_int: can_intgrp {
+		fsl,pins = <
+			VF610_PAD_PTB21__GPIO_43	0x22ed
+		>;
 	};
 };
diff --git a/arch/arm/boot/dts/nxp/vf/vf-colibri.dtsi b/arch/arm/boot/dts/nxp/vf/vf-colibri.dtsi
new file mode 100644
index 000000000000..98f9ee1b0030
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/vf/vf-colibri.dtsi
@@ -0,0 +1,348 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright 2014-2020 Toradex
+ *
+ */
+
+/ {
+	aliases {
+		ethernet0 = &fec1;
+		ethernet1 = &fec0;
+	};
+
+	bl: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_bl_on>;
+		pwms = <&pwm0 0 5000000 0>;
+		enable-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+
+	reg_module_3v3: regulator-module-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "+V3.3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_module_3v3_avdd: regulator-module-3v3-avdd {
+		compatible = "regulator-fixed";
+		regulator-name = "+V3.3_AVDD_AUDIO";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&adc0 {
+	status = "okay";
+	vref-supply = <&reg_module_3v3_avdd>;
+};
+
+&adc1 {
+	status = "okay";
+	vref-supply = <&reg_module_3v3_avdd>;
+};
+
+&can0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan0>;
+	status = "disabled";
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	status = "disabled";
+};
+
+&clks {
+	assigned-clocks = <&clks VF610_CLK_ENET_SEL>,
+			  <&clks VF610_CLK_ENET_TS_SEL>;
+	assigned-clock-parents = <&clks VF610_CLK_ENET_50M>,
+				 <&clks VF610_CLK_ENET_50M>;
+};
+
+&dspi1 {
+	bus-num = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_dspi1>;
+};
+
+&edma0 {
+	status = "okay";
+};
+
+&edma1 {
+	status = "okay";
+};
+
+&esdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc1>;
+	bus-width = <4>;
+	cd-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+	disable-wp;
+};
+
+&fec1 {
+	phy-mode = "rmii";
+	phy-supply = <&reg_module_3v3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c0>;
+	pinctrl-1 = <&pinctrl_i2c0_gpio>;
+	scl-gpios = <&gpio1 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio1 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+};
+
+&nfc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_nfc>;
+	status = "okay";
+
+	nand@0 {
+		compatible = "fsl,vf610-nfc-nandcs";
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		nand-bus-width = <8>;
+		nand-ecc-mode = "hw";
+		nand-ecc-strength = <32>;
+		nand-ecc-step-size = <2048>;
+		nand-on-flash-bbt;
+	};
+};
+
+&pwm0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0>;
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart0>;
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+};
+
+&usbdev0 {
+	disable-over-current;
+	status = "okay";
+};
+
+&usbh1 {
+	disable-over-current;
+	status = "okay";
+};
+
+&usbmisc0 {
+	status = "okay";
+};
+
+&usbmisc1 {
+	status = "okay";
+};
+
+&usbphy0 {
+	status = "okay";
+};
+
+&usbphy1 {
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_flexcan0: can0grp {
+		fsl,pins = <
+			VF610_PAD_PTB14__CAN0_RX	0x31F1
+			VF610_PAD_PTB15__CAN0_TX	0x31F2
+		>;
+	};
+
+	pinctrl_flexcan1: can1grp {
+		fsl,pins = <
+			VF610_PAD_PTB16__CAN1_RX	0x31F1
+			VF610_PAD_PTB17__CAN1_TX	0x31F2
+		>;
+	};
+
+	pinctrl_gpio_ext: gpio_extgrp {
+		fsl,pins = <
+			VF610_PAD_PTD10__GPIO_89	0x22ed /* EXT_IO_0 */
+			VF610_PAD_PTD9__GPIO_88		0x22ed /* EXT_IO_1 */
+			VF610_PAD_PTD26__GPIO_68	0x22ed /* EXT_IO_2 */
+		>;
+	};
+
+	pinctrl_dcu0_1: dcu01grp {
+		fsl,pins = <
+			VF610_PAD_PTE0__DCU0_HSYNC	0x1902
+			VF610_PAD_PTE1__DCU0_VSYNC	0x1902
+			VF610_PAD_PTE2__DCU0_PCLK	0x1902
+			VF610_PAD_PTE4__DCU0_DE		0x1902
+			VF610_PAD_PTE5__DCU0_R0		0x1902
+			VF610_PAD_PTE6__DCU0_R1		0x1902
+			VF610_PAD_PTE7__DCU0_R2		0x1902
+			VF610_PAD_PTE8__DCU0_R3		0x1902
+			VF610_PAD_PTE9__DCU0_R4		0x1902
+			VF610_PAD_PTE10__DCU0_R5	0x1902
+			VF610_PAD_PTE11__DCU0_R6	0x1902
+			VF610_PAD_PTE12__DCU0_R7	0x1902
+			VF610_PAD_PTE13__DCU0_G0	0x1902
+			VF610_PAD_PTE14__DCU0_G1	0x1902
+			VF610_PAD_PTE15__DCU0_G2	0x1902
+			VF610_PAD_PTE16__DCU0_G3	0x1902
+			VF610_PAD_PTE17__DCU0_G4	0x1902
+			VF610_PAD_PTE18__DCU0_G5	0x1902
+			VF610_PAD_PTE19__DCU0_G6	0x1902
+			VF610_PAD_PTE20__DCU0_G7	0x1902
+			VF610_PAD_PTE21__DCU0_B0	0x1902
+			VF610_PAD_PTE22__DCU0_B1	0x1902
+			VF610_PAD_PTE23__DCU0_B2	0x1902
+			VF610_PAD_PTE24__DCU0_B3	0x1902
+			VF610_PAD_PTE25__DCU0_B4	0x1902
+			VF610_PAD_PTE26__DCU0_B5	0x1902
+			VF610_PAD_PTE27__DCU0_B6	0x1902
+			VF610_PAD_PTE28__DCU0_B7	0x1902
+		>;
+	};
+
+	pinctrl_dspi1: dspi1grp {
+		fsl,pins = <
+			VF610_PAD_PTD5__DSPI1_CS0		0x33e2
+			VF610_PAD_PTD6__DSPI1_SIN		0x33e1
+			VF610_PAD_PTD7__DSPI1_SOUT		0x33e2
+			VF610_PAD_PTD8__DSPI1_SCK		0x33e2
+		>;
+	};
+
+	pinctrl_esdhc1: esdhc1grp {
+		fsl,pins = <
+			VF610_PAD_PTA24__ESDHC1_CLK	0x31ef
+			VF610_PAD_PTA25__ESDHC1_CMD	0x31ef
+			VF610_PAD_PTA26__ESDHC1_DAT0	0x31ef
+			VF610_PAD_PTA27__ESDHC1_DAT1	0x31ef
+			VF610_PAD_PTA28__ESDHC1_DATA2	0x31ef
+			VF610_PAD_PTA29__ESDHC1_DAT3	0x31ef
+			VF610_PAD_PTB20__GPIO_42	0x219d
+		>;
+	};
+
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <
+			VF610_PAD_PTA6__RMII_CLKOUT		0x30d2
+			VF610_PAD_PTC9__ENET_RMII1_MDC		0x30d2
+			VF610_PAD_PTC10__ENET_RMII1_MDIO	0x30d3
+			VF610_PAD_PTC11__ENET_RMII1_CRS		0x30d1
+			VF610_PAD_PTC12__ENET_RMII1_RXD1	0x30d1
+			VF610_PAD_PTC13__ENET_RMII1_RXD0	0x30d1
+			VF610_PAD_PTC14__ENET_RMII1_RXER	0x30d1
+			VF610_PAD_PTC15__ENET_RMII1_TXD1	0x30d2
+			VF610_PAD_PTC16__ENET_RMII1_TXD0	0x30d2
+			VF610_PAD_PTC17__ENET_RMII1_TXEN	0x30d2
+		>;
+	};
+
+	pinctrl_gpio_bl_on: gpio_bl_ongrp {
+		fsl,pins = <
+			VF610_PAD_PTC0__GPIO_45		0x22ef
+		>;
+	};
+
+	pinctrl_i2c0: i2c0grp {
+		fsl,pins = <
+			VF610_PAD_PTB14__I2C0_SCL		0x37ff
+			VF610_PAD_PTB15__I2C0_SDA		0x37ff
+		>;
+	};
+
+	pinctrl_i2c0_gpio: i2c0gpiogrp {
+		fsl,pins = <
+			VF610_PAD_PTB14__GPIO_36		0x37ff
+			VF610_PAD_PTB15__GPIO_37		0x37ff
+		>;
+	};
+
+	pinctrl_nfc: nfcgrp {
+		fsl,pins = <
+			VF610_PAD_PTD23__NF_IO7		0x28df
+			VF610_PAD_PTD22__NF_IO6		0x28df
+			VF610_PAD_PTD21__NF_IO5		0x28df
+			VF610_PAD_PTD20__NF_IO4		0x28df
+			VF610_PAD_PTD19__NF_IO3		0x28df
+			VF610_PAD_PTD18__NF_IO2		0x28df
+			VF610_PAD_PTD17__NF_IO1		0x28df
+			VF610_PAD_PTD16__NF_IO0		0x28df
+			VF610_PAD_PTB24__NF_WE_B	0x28c2
+			VF610_PAD_PTB25__NF_CE0_B	0x28c2
+			VF610_PAD_PTB27__NF_RE_B	0x28c2
+			VF610_PAD_PTC26__NF_RB_B	0x283d
+			VF610_PAD_PTC27__NF_ALE		0x28c2
+			VF610_PAD_PTC28__NF_CLE		0x28c2
+		>;
+	};
+
+	pinctrl_pwm0: pwm0grp {
+		fsl,pins = <
+			VF610_PAD_PTB0__FTM0_CH0		0x1182
+			VF610_PAD_PTB1__FTM0_CH1		0x1182
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			VF610_PAD_PTB8__FTM1_CH0		0x1182
+			VF610_PAD_PTB9__FTM1_CH1		0x1182
+		>;
+	};
+
+	pinctrl_uart0: uart0grp {
+		fsl,pins = <
+			VF610_PAD_PTB10__UART0_TX		0x21a2
+			VF610_PAD_PTB11__UART0_RX		0x21a1
+			VF610_PAD_PTB12__UART0_RTS		0x21a2
+			VF610_PAD_PTB13__UART0_CTS		0x21a1
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			VF610_PAD_PTB4__UART1_TX		0x21a2
+			VF610_PAD_PTB5__UART1_RX		0x21a1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			VF610_PAD_PTD0__UART2_TX		0x21a2
+			VF610_PAD_PTD1__UART2_RX		0x21a1
+			VF610_PAD_PTD2__UART2_RTS		0x21a2
+			VF610_PAD_PTD3__UART2_CTS		0x21a1
+		>;
+	};
+
+	pinctrl_usbh1_reg: gpio_usb_vbusgrp {
+		fsl,pins = <
+			VF610_PAD_PTD4__GPIO_83			0x22ed
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/vf500-colibri-eval-v3.dts b/arch/arm/boot/dts/nxp/vf/vf500-colibri-eval-v3.dts
index 088964f8dc4b..088964f8dc4b 100644
--- a/arch/arm/boot/dts/vf500-colibri-eval-v3.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf500-colibri-eval-v3.dts
diff --git a/arch/arm/boot/dts/vf500-colibri.dtsi b/arch/arm/boot/dts/nxp/vf/vf500-colibri.dtsi
index 8af7ed56e653..ae3403c766d6 100644
--- a/arch/arm/boot/dts/vf500-colibri.dtsi
+++ b/arch/arm/boot/dts/nxp/vf/vf500-colibri.dtsi
@@ -40,30 +40,28 @@
 };
 
 &iomuxc {
-	vf610-colibri {
-		pinctrl_touchctrl_idle: touchctrl_idle {
-			fsl,pins = <
-				VF610_PAD_PTA18__GPIO_8		0x006d
-				VF610_PAD_PTA19__GPIO_9		0x006c
-				>;
-		};
+	pinctrl_touchctrl_idle: touchctrl_idlegrp {
+		fsl,pins = <
+			VF610_PAD_PTA18__GPIO_8		0x006d
+			VF610_PAD_PTA19__GPIO_9		0x006c
+			>;
+	};
 
-		pinctrl_touchctrl_default: touchctrl_default {
-			fsl,pins = <
-				VF610_PAD_PTA18__ADC0_SE0	0x0040
-				VF610_PAD_PTA19__ADC0_SE1	0x0040
-				VF610_PAD_PTA16__ADC1_SE0	0x0040
-				VF610_PAD_PTB2__ADC1_SE2	0x0040
-				>;
-		};
+	pinctrl_touchctrl_default: touchctrl_defaultgrp {
+		fsl,pins = <
+			VF610_PAD_PTA18__ADC0_SE0	0x0040
+			VF610_PAD_PTA19__ADC0_SE1	0x0040
+			VF610_PAD_PTA16__ADC1_SE0	0x0040
+			VF610_PAD_PTB2__ADC1_SE2	0x0040
+			>;
+	};
 
-		pinctrl_touchctrl_gpios: touchctrl_gpios {
-			fsl,pins = <
-				VF610_PAD_PTA23__GPIO_13	0x22e9
-				VF610_PAD_PTB23__GPIO_93	0x22e9
-				VF610_PAD_PTA22__GPIO_12	0x22e9
-				VF610_PAD_PTA11__GPIO_4		0x22e9
-				>;
-		};
+	pinctrl_touchctrl_gpios: touchctrl_gpiosgrp {
+		fsl,pins = <
+			VF610_PAD_PTA23__GPIO_13	0x22e9
+			VF610_PAD_PTB23__GPIO_93	0x22e9
+			VF610_PAD_PTA22__GPIO_12	0x22e9
+			VF610_PAD_PTA11__GPIO_4		0x22e9
+			>;
 	};
 };
diff --git a/arch/arm/boot/dts/vf500.dtsi b/arch/arm/boot/dts/nxp/vf/vf500.dtsi
index 0c0dd442300a..71ccdaa6f269 100644
--- a/arch/arm/boot/dts/vf500.dtsi
+++ b/arch/arm/boot/dts/nxp/vf/vf500.dtsi
@@ -43,15 +43,13 @@
 			};
 		};
 
-		bus@40080000 {
-			pmu@40089000 {
-				compatible = "arm,cortex-a5-pmu";
-				interrupts = <7 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-affinity = <&a5_cpu>;
-				reg = <0x40089000 0x1000>;
-			};
-		};
+	};
 
+	pmu {
+		compatible = "arm,cortex-a5-pmu";
+		interrupts = <7 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&a5_cpu>;
+		interrupt-parent = <&mscm_ir>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/vf610-bk4.dts b/arch/arm/boot/dts/nxp/vf/vf610-bk4.dts
index 830c85476b3d..e36c854dc297 100644
--- a/arch/arm/boot/dts/vf610-bk4.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-bk4.dts
@@ -38,7 +38,7 @@
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
 		/* LED D5 */
-		led0: heartbeat {
+		led0: led-heartbeat {
 			label = "heartbeat";
 			gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
@@ -61,14 +61,14 @@
 		regulator-max-microvolt = <3300000>;
 	};
 
-	spi-gpio {
+	spi {
 		compatible = "spi-gpio";
 		pinctrl-0 = <&pinctrl_gpio_spi>;
 		pinctrl-names = "default";
 		#address-cells = <1>;
 		#size-cells = <0>;
 		/* PTD12 ->RPIO[91] */
-		sck-gpios  = <&gpio2 27 GPIO_ACTIVE_LOW>;
+		sck-gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
 		/* PTD10 ->RPIO[89] */
 		miso-gpios = <&gpio2 25 GPIO_ACTIVE_HIGH>;
 		num-chipselects = <0>;
@@ -79,7 +79,7 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 			/* PTB18 -> RGPIO[40] */
-			load-gpios  = <&gpio1 8 GPIO_ACTIVE_LOW>;
+			load-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
 			spi-max-frequency = <100000>;
 		};
 	};
@@ -119,7 +119,7 @@
 	status = "okay";
 
 	spidev0@0 {
-		compatible = "lwn,bk4";
+		compatible = "lwn,bk4-spi";
 		spi-max-frequency = <30000000>;
 		reg = <0>;
 		fsl,spi-cs-sck-delay = <200>;
@@ -136,7 +136,7 @@
 	#address-cells = <0>;
 
 	slave {
-		compatible = "lwn,bk4";
+		compatible = "lwn,bk4-spi";
 		spi-max-frequency = <30000000>;
 	};
 };
@@ -458,7 +458,7 @@
 		>;
 	};
 
-	pinctrl_gpio_spi: pinctrl-gpio-spi {
+	pinctrl_gpio_spi: pinctrl-gpio-spigrp {
 		fsl,pins = <
 			VF610_PAD_PTB18__GPIO_40        0x1183
 			VF610_PAD_PTD10__GPIO_89        0x1183
diff --git a/arch/arm/boot/dts/vf610-colibri-eval-v3.dts b/arch/arm/boot/dts/nxp/vf/vf610-colibri-eval-v3.dts
index fb661e8a2dc6..fb661e8a2dc6 100644
--- a/arch/arm/boot/dts/vf610-colibri-eval-v3.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-colibri-eval-v3.dts
diff --git a/arch/arm/boot/dts/vf610-colibri.dtsi b/arch/arm/boot/dts/nxp/vf/vf610-colibri.dtsi
index 607cec2df861..20aed3946214 100644
--- a/arch/arm/boot/dts/vf610-colibri.dtsi
+++ b/arch/arm/boot/dts/nxp/vf/vf610-colibri.dtsi
@@ -8,7 +8,6 @@
 
 / {
 	model = "Toradex Colibri VF61 COM";
-	compatible = "toradex,vf610-colibri_vf61", "fsl,vf610";
 
 	memory@80000000 {
 		device_type = "memory";
diff --git a/arch/arm/boot/dts/vf610-cosmic.dts b/arch/arm/boot/dts/nxp/vf/vf610-cosmic.dts
index 703f375d7e24..f1e6344b0c69 100644
--- a/arch/arm/boot/dts/vf610-cosmic.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-cosmic.dts
@@ -47,39 +47,37 @@
 };
 
 &iomuxc {
-	vf610-cosmic {
-		pinctrl_esdhc1: esdhc1grp {
-			fsl,pins = <
-				VF610_PAD_PTA24__ESDHC1_CLK	0x31ef
-				VF610_PAD_PTA25__ESDHC1_CMD	0x31ef
-				VF610_PAD_PTA26__ESDHC1_DAT0	0x31ef
-				VF610_PAD_PTA27__ESDHC1_DAT1	0x31ef
-				VF610_PAD_PTA28__ESDHC1_DATA2	0x31ef
-				VF610_PAD_PTA29__ESDHC1_DAT3	0x31ef
-				VF610_PAD_PTB28__GPIO_98	0x219d
-			>;
-		};
+	pinctrl_esdhc1: esdhc1grp {
+		fsl,pins = <
+			VF610_PAD_PTA24__ESDHC1_CLK	0x31ef
+			VF610_PAD_PTA25__ESDHC1_CMD	0x31ef
+			VF610_PAD_PTA26__ESDHC1_DAT0	0x31ef
+			VF610_PAD_PTA27__ESDHC1_DAT1	0x31ef
+			VF610_PAD_PTA28__ESDHC1_DATA2	0x31ef
+			VF610_PAD_PTA29__ESDHC1_DAT3	0x31ef
+			VF610_PAD_PTB28__GPIO_98	0x219d
+		>;
+	};
 
-		pinctrl_fec1: fec1grp {
-			fsl,pins = <
-				VF610_PAD_PTC9__ENET_RMII1_MDC		0x30d2
-				VF610_PAD_PTC10__ENET_RMII1_MDIO	0x30d3
-				VF610_PAD_PTC11__ENET_RMII1_CRS		0x30d1
-				VF610_PAD_PTC12__ENET_RMII1_RXD1	0x30d1
-				VF610_PAD_PTC13__ENET_RMII1_RXD0	0x30d1
-				VF610_PAD_PTC14__ENET_RMII1_RXER	0x30d1
-				VF610_PAD_PTC15__ENET_RMII1_TXD1	0x30d2
-				VF610_PAD_PTC16__ENET_RMII1_TXD0	0x30d2
-				VF610_PAD_PTC17__ENET_RMII1_TXEN	0x30d2
-			>;
-		};
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <
+			VF610_PAD_PTC9__ENET_RMII1_MDC		0x30d2
+			VF610_PAD_PTC10__ENET_RMII1_MDIO	0x30d3
+			VF610_PAD_PTC11__ENET_RMII1_CRS		0x30d1
+			VF610_PAD_PTC12__ENET_RMII1_RXD1	0x30d1
+			VF610_PAD_PTC13__ENET_RMII1_RXD0	0x30d1
+			VF610_PAD_PTC14__ENET_RMII1_RXER	0x30d1
+			VF610_PAD_PTC15__ENET_RMII1_TXD1	0x30d2
+			VF610_PAD_PTC16__ENET_RMII1_TXD0	0x30d2
+			VF610_PAD_PTC17__ENET_RMII1_TXEN	0x30d2
+		>;
+	};
 
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				VF610_PAD_PTB4__UART1_TX		0x21a2
-				VF610_PAD_PTB5__UART1_RX		0x21a1
-			>;
-		};
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			VF610_PAD_PTB4__UART1_TX		0x21a2
+			VF610_PAD_PTB5__UART1_RX		0x21a1
+		>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/vf610-pinfunc.h b/arch/arm/boot/dts/nxp/vf/vf610-pinfunc.h
index f1e5a7cf58a9..b7b7322a2d1b 100644
--- a/arch/arm/boot/dts/vf610-pinfunc.h
+++ b/arch/arm/boot/dts/nxp/vf/vf610-pinfunc.h
@@ -420,7 +420,7 @@
 #define VF610_PAD_PTD29__FTM3_CH2		0x104 0x000 ALT4 0x0
 #define VF610_PAD_PTD29__DSPI2_SIN		0x104 0x000 ALT5 0x0
 #define VF610_PAD_PTD29__DEBUG_OUT11		0x104 0x000 ALT7 0x0
-#define VF610_PAD_PTD28__GPIO_66	 	0x108 0x000 ALT0 0x0
+#define VF610_PAD_PTD28__GPIO_66		0x108 0x000 ALT0 0x0
 #define VF610_PAD_PTD28__FB_AD28		0x108 0x000 ALT1 0x0
 #define VF610_PAD_PTD28__NF_IO12		0x108 0x000 ALT2 0x0
 #define VF610_PAD_PTD28__I2C2_SCL		0x108 0x34C ALT3 0x1
@@ -802,5 +802,55 @@
 #define VF610_PAD_PTE28__EWM_OUT		0x214 0x000 ALT7 0x0
 #define VF610_PAD_PTA7__GPIO_134		0x218 0x000 ALT0 0x0
 #define VF610_PAD_PTA7__VIU_PIX_CLK		0x218 0x3AC ALT1 0x1
+#define VF610_PAD_DDR_RESETB			0x21c 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A15__DDR_A_15		0x220 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A14__DDR_A_14		0x224 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A13__DDR_A_13		0x228 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A12__DDR_A_12		0x22c 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A11__DDR_A_11		0x230 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A10__DDR_A_10		0x234 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A9__DDR_A_9		0x238 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A8__DDR_A_8		0x23c 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A7__DDR_A_7		0x240 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A6__DDR_A_6		0x244 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A5__DDR_A_5		0x248 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A4__DDR_A_4		0x24c 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A3__DDR_A_3		0x250 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A2__DDR_A_2		0x254 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A1__DDR_A_1		0x258 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A0__DDR_A_0		0x25c 0x000 ALT0 0x0
+#define VF610_PAD_DDR_BA2__DDR_BA_2		0x260 0x000 ALT0 0x0
+#define VF610_PAD_DDR_BA1__DDR_BA_1		0x264 0x000 ALT0 0x0
+#define VF610_PAD_DDR_BA0__DDR_BA_0		0x268 0x000 ALT0 0x0
+#define VF610_PAD_DDR_CAS__DDR_CAS_B		0x26c 0x000 ALT0 0x0
+#define VF610_PAD_DDR_CKE__DDR_CKE_0		0x270 0x000 ALT0 0x0
+#define VF610_PAD_DDR_CLK__DDR_CLK_0		0x274 0x000 ALT0 0x0
+#define VF610_PAD_DDR_CS__DDR_CS_B_0		0x278 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D15__DDR_D_15		0x27c 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D14__DDR_D_14		0x280 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D13__DDR_D_13		0x284 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D12__DDR_D_12		0x288 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D11__DDR_D_11		0x28c 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D10__DDR_D_10		0x290 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D9__DDR_D_9		0x294 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D8__DDR_D_8		0x298 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D7__DDR_D_7		0x29c 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D6__DDR_D_6		0x2a0 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D5__DDR_D_5		0x2a4 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D4__DDR_D_4		0x2a8 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D3__DDR_D_3		0x2ac 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D2__DDR_D_2		0x2b0 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D1__DDR_D_1		0x2b4 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D0__DDR_D_0		0x2b8 0x000 ALT0 0x0
+#define VF610_PAD_DDR_DQM1__DDR_DQM_1		0x2bc 0x000 ALT0 0x0
+#define VF610_PAD_DDR_DQM0__DDR_DQM_0		0x2c0 0x000 ALT0 0x0
+#define VF610_PAD_DDR_DQS1__DDR_DQS_1		0x2c4 0x000 ALT0 0x0
+#define VF610_PAD_DDR_DQS0__DDR_DQS_0		0x2c8 0x000 ALT0 0x0
+#define VF610_PAD_DDR_RAS__DDR_RAS_B		0x2cc 0x000 ALT0 0x0
+#define VF610_PAD_DDR_WE__DDR_WE_B		0x2d0 0x000 ALT0 0x0
+#define VF610_PAD_DDR_ODT1__DDR_ODT_0		0x2d4 0x000 ALT0 0x0
+#define VF610_PAD_DDR_ODT0__DDR_ODT_1		0x2d8 0x000 ALT0 0x0
+#define VF610_PAD_DDR_DDRBYTE1__DDR_DDRBYTE1	0x2dc 0x000 ALT0 0x0
+#define VF610_PAD_DDR_DDRBYTE2__DDR_DDRBYTE2	0x2e0 0x000 ALT0 0x0
 
 #endif
diff --git a/arch/arm/boot/dts/vf610-twr.dts b/arch/arm/boot/dts/nxp/vf/vf610-twr.dts
index dbb5ffcdcec4..e7c2f6d46ab2 100644
--- a/arch/arm/boot/dts/vf610-twr.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-twr.dts
@@ -30,27 +30,20 @@
 		clock-frequency = <50000000>;
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		reg_3p3v: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "3P3V";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
 
-		reg_vcc_3v3_mcu: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "vcc_3v3_mcu";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-		};
+	reg_vcc_3v3_mcu: regulator-vcc-3v3-mcu {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_3v3_mcu";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
 	};
 
 	sound {
@@ -169,135 +162,133 @@
 	       VDDA-supply = <&reg_3p3v>;
 	       VDDIO-supply = <&reg_3p3v>;
 	       clocks = <&clks VF610_CLK_SAI2>;
-       };
+	};
 };
 
 &iomuxc {
-	vf610-twr {
-		pinctrl_adc0_ad5: adc0ad5grp {
-			fsl,pins = <
-				VF610_PAD_PTC30__ADC0_SE5		0xa1
-			>;
-		};
+	pinctrl_adc0_ad5: adc0ad5grp {
+		fsl,pins = <
+			VF610_PAD_PTC30__ADC0_SE5		0xa1
+		>;
+	};
 
-		pinctrl_dspi0: dspi0grp {
-			fsl,pins = <
-				VF610_PAD_PTB19__DSPI0_CS0		0x1182
-				VF610_PAD_PTB20__DSPI0_SIN		0x1181
-				VF610_PAD_PTB21__DSPI0_SOUT		0x1182
-				VF610_PAD_PTB22__DSPI0_SCK		0x1182
-			>;
-		};
+	pinctrl_dspi0: dspi0grp {
+		fsl,pins = <
+			VF610_PAD_PTB19__DSPI0_CS0		0x1182
+			VF610_PAD_PTB20__DSPI0_SIN		0x1181
+			VF610_PAD_PTB21__DSPI0_SOUT		0x1182
+			VF610_PAD_PTB22__DSPI0_SCK		0x1182
+		>;
+	};
 
-		pinctrl_esdhc1: esdhc1grp {
-			fsl,pins = <
-				VF610_PAD_PTA24__ESDHC1_CLK	0x31ef
-				VF610_PAD_PTA25__ESDHC1_CMD	0x31ef
-				VF610_PAD_PTA26__ESDHC1_DAT0	0x31ef
-				VF610_PAD_PTA27__ESDHC1_DAT1	0x31ef
-				VF610_PAD_PTA28__ESDHC1_DATA2	0x31ef
-				VF610_PAD_PTA29__ESDHC1_DAT3	0x31ef
-				VF610_PAD_PTA7__GPIO_134	0x219d
-			>;
-		};
+	pinctrl_esdhc1: esdhc1grp {
+		fsl,pins = <
+			VF610_PAD_PTA24__ESDHC1_CLK	0x31ef
+			VF610_PAD_PTA25__ESDHC1_CMD	0x31ef
+			VF610_PAD_PTA26__ESDHC1_DAT0	0x31ef
+			VF610_PAD_PTA27__ESDHC1_DAT1	0x31ef
+			VF610_PAD_PTA28__ESDHC1_DATA2	0x31ef
+			VF610_PAD_PTA29__ESDHC1_DAT3	0x31ef
+			VF610_PAD_PTA7__GPIO_134	0x219d
+		>;
+	};
 
-		pinctrl_fec0: fec0grp {
-			fsl,pins = <
-				VF610_PAD_PTA6__RMII_CLKIN		0x30d1
-				VF610_PAD_PTC0__ENET_RMII0_MDC		0x30d3
-				VF610_PAD_PTC1__ENET_RMII0_MDIO		0x30d1
-				VF610_PAD_PTC2__ENET_RMII0_CRS		0x30d1
-				VF610_PAD_PTC3__ENET_RMII0_RXD1		0x30d1
-				VF610_PAD_PTC4__ENET_RMII0_RXD0		0x30d1
-				VF610_PAD_PTC5__ENET_RMII0_RXER		0x30d1
-				VF610_PAD_PTC6__ENET_RMII0_TXD1		0x30d2
-				VF610_PAD_PTC7__ENET_RMII0_TXD0		0x30d2
-				VF610_PAD_PTC8__ENET_RMII0_TXEN		0x30d2
-			>;
-		};
+	pinctrl_fec0: fec0grp {
+		fsl,pins = <
+			VF610_PAD_PTA6__RMII_CLKIN		0x30d1
+			VF610_PAD_PTC0__ENET_RMII0_MDC		0x30d3
+			VF610_PAD_PTC1__ENET_RMII0_MDIO		0x30d1
+			VF610_PAD_PTC2__ENET_RMII0_CRS		0x30d1
+			VF610_PAD_PTC3__ENET_RMII0_RXD1		0x30d1
+			VF610_PAD_PTC4__ENET_RMII0_RXD0		0x30d1
+			VF610_PAD_PTC5__ENET_RMII0_RXER		0x30d1
+			VF610_PAD_PTC6__ENET_RMII0_TXD1		0x30d2
+			VF610_PAD_PTC7__ENET_RMII0_TXD0		0x30d2
+			VF610_PAD_PTC8__ENET_RMII0_TXEN		0x30d2
+		>;
+	};
 
-		pinctrl_fec1: fec1grp {
-			fsl,pins = <
-				VF610_PAD_PTC9__ENET_RMII1_MDC		0x30d2
-				VF610_PAD_PTC10__ENET_RMII1_MDIO	0x30d3
-				VF610_PAD_PTC11__ENET_RMII1_CRS		0x30d1
-				VF610_PAD_PTC12__ENET_RMII1_RXD1	0x30d1
-				VF610_PAD_PTC13__ENET_RMII1_RXD0	0x30d1
-				VF610_PAD_PTC14__ENET_RMII1_RXER	0x30d1
-				VF610_PAD_PTC15__ENET_RMII1_TXD1	0x30d2
-				VF610_PAD_PTC16__ENET_RMII1_TXD0	0x30d2
-				VF610_PAD_PTC17__ENET_RMII1_TXEN	0x30d2
-			>;
-		};
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <
+			VF610_PAD_PTC9__ENET_RMII1_MDC		0x30d2
+			VF610_PAD_PTC10__ENET_RMII1_MDIO	0x30d3
+			VF610_PAD_PTC11__ENET_RMII1_CRS		0x30d1
+			VF610_PAD_PTC12__ENET_RMII1_RXD1	0x30d1
+			VF610_PAD_PTC13__ENET_RMII1_RXD0	0x30d1
+			VF610_PAD_PTC14__ENET_RMII1_RXER	0x30d1
+			VF610_PAD_PTC15__ENET_RMII1_TXD1	0x30d2
+			VF610_PAD_PTC16__ENET_RMII1_TXD0	0x30d2
+			VF610_PAD_PTC17__ENET_RMII1_TXEN	0x30d2
+		>;
+	};
 
-		pinctrl_i2c0: i2c0grp {
-			fsl,pins = <
-				VF610_PAD_PTB14__I2C0_SCL		0x30d3
-				VF610_PAD_PTB15__I2C0_SDA		0x30d3
-			>;
-		};
+	pinctrl_i2c0: i2c0grp {
+		fsl,pins = <
+			VF610_PAD_PTB14__I2C0_SCL		0x30d3
+			VF610_PAD_PTB15__I2C0_SDA		0x30d3
+		>;
+	};
 
-		pinctrl_nfc: nfcgrp {
-			fsl,pins = <
-				VF610_PAD_PTD31__NF_IO15	0x28df
-				VF610_PAD_PTD30__NF_IO14	0x28df
-				VF610_PAD_PTD29__NF_IO13	0x28df
-				VF610_PAD_PTD28__NF_IO12	0x28df
-				VF610_PAD_PTD27__NF_IO11	0x28df
-				VF610_PAD_PTD26__NF_IO10	0x28df
-				VF610_PAD_PTD25__NF_IO9		0x28df
-				VF610_PAD_PTD24__NF_IO8		0x28df
-				VF610_PAD_PTD23__NF_IO7		0x28df
-				VF610_PAD_PTD22__NF_IO6		0x28df
-				VF610_PAD_PTD21__NF_IO5		0x28df
-				VF610_PAD_PTD20__NF_IO4		0x28df
-				VF610_PAD_PTD19__NF_IO3		0x28df
-				VF610_PAD_PTD18__NF_IO2		0x28df
-				VF610_PAD_PTD17__NF_IO1		0x28df
-				VF610_PAD_PTD16__NF_IO0		0x28df
-				VF610_PAD_PTB24__NF_WE_B	0x28c2
-				VF610_PAD_PTB25__NF_CE0_B	0x28c2
-				VF610_PAD_PTB27__NF_RE_B	0x28c2
-				VF610_PAD_PTC26__NF_RB_B	0x283d
-				VF610_PAD_PTC27__NF_ALE		0x28c2
-				VF610_PAD_PTC28__NF_CLE		0x28c2
-			>;
-		};
+	pinctrl_nfc: nfcgrp {
+		fsl,pins = <
+			VF610_PAD_PTD31__NF_IO15	0x28df
+			VF610_PAD_PTD30__NF_IO14	0x28df
+			VF610_PAD_PTD29__NF_IO13	0x28df
+			VF610_PAD_PTD28__NF_IO12	0x28df
+			VF610_PAD_PTD27__NF_IO11	0x28df
+			VF610_PAD_PTD26__NF_IO10	0x28df
+			VF610_PAD_PTD25__NF_IO9		0x28df
+			VF610_PAD_PTD24__NF_IO8		0x28df
+			VF610_PAD_PTD23__NF_IO7		0x28df
+			VF610_PAD_PTD22__NF_IO6		0x28df
+			VF610_PAD_PTD21__NF_IO5		0x28df
+			VF610_PAD_PTD20__NF_IO4		0x28df
+			VF610_PAD_PTD19__NF_IO3		0x28df
+			VF610_PAD_PTD18__NF_IO2		0x28df
+			VF610_PAD_PTD17__NF_IO1		0x28df
+			VF610_PAD_PTD16__NF_IO0		0x28df
+			VF610_PAD_PTB24__NF_WE_B	0x28c2
+			VF610_PAD_PTB25__NF_CE0_B	0x28c2
+			VF610_PAD_PTB27__NF_RE_B	0x28c2
+			VF610_PAD_PTC26__NF_RB_B	0x283d
+			VF610_PAD_PTC27__NF_ALE		0x28c2
+			VF610_PAD_PTC28__NF_CLE		0x28c2
+		>;
+	};
 
-		pinctrl_pwm0: pwm0grp {
-			fsl,pins = <
-				VF610_PAD_PTB0__FTM0_CH0		0x1582
-				VF610_PAD_PTB1__FTM0_CH1		0x1582
-				VF610_PAD_PTB2__FTM0_CH2		0x1582
-				VF610_PAD_PTB3__FTM0_CH3		0x1582
-			>;
-		};
+	pinctrl_pwm0: pwm0grp {
+		fsl,pins = <
+			VF610_PAD_PTB0__FTM0_CH0		0x1582
+			VF610_PAD_PTB1__FTM0_CH1		0x1582
+			VF610_PAD_PTB2__FTM0_CH2		0x1582
+			VF610_PAD_PTB3__FTM0_CH3		0x1582
+		>;
+	};
 
-		pinctrl_sai2: sai2grp {
-			fsl,pins = <
-				VF610_PAD_PTA16__SAI2_TX_BCLK		0x02ed
-				VF610_PAD_PTA18__SAI2_TX_DATA		0x02ee
-				VF610_PAD_PTA19__SAI2_TX_SYNC		0x02ed
-				VF610_PAD_PTA21__SAI2_RX_BCLK		0x02ed
-				VF610_PAD_PTA22__SAI2_RX_DATA		0x02ed
-				VF610_PAD_PTA23__SAI2_RX_SYNC		0x02ed
-				VF610_PAD_PTB18__EXT_AUDIO_MCLK		0x02ed
-			>;
-		};
+	pinctrl_sai2: sai2grp {
+		fsl,pins = <
+			VF610_PAD_PTA16__SAI2_TX_BCLK		0x02ed
+			VF610_PAD_PTA18__SAI2_TX_DATA		0x02ee
+			VF610_PAD_PTA19__SAI2_TX_SYNC		0x02ed
+			VF610_PAD_PTA21__SAI2_RX_BCLK		0x02ed
+			VF610_PAD_PTA22__SAI2_RX_DATA		0x02ed
+			VF610_PAD_PTA23__SAI2_RX_SYNC		0x02ed
+			VF610_PAD_PTB18__EXT_AUDIO_MCLK		0x02ed
+		>;
+	};
 
-		pinctrl_uart1: uart1grp {
-			fsl,pins = <
-				VF610_PAD_PTB4__UART1_TX		0x21a2
-				VF610_PAD_PTB5__UART1_RX		0x21a1
-			>;
-		};
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			VF610_PAD_PTB4__UART1_TX		0x21a2
+			VF610_PAD_PTB5__UART1_RX		0x21a1
+		>;
+	};
 
-		pinctrl_uart2: uart2grp {
-			fsl,pins = <
-				VF610_PAD_PTB6__UART2_TX		0x21a2
-				VF610_PAD_PTB7__UART2_RX		0x21a1
-			>;
-		};
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			VF610_PAD_PTB6__UART2_TX		0x21a2
+			VF610_PAD_PTB7__UART2_RX		0x21a1
+		>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/vf610-zii-cfu1.dts b/arch/arm/boot/dts/nxp/vf/vf610-zii-cfu1.dts
index 96495d965163..929426c1299c 100644
--- a/arch/arm/boot/dts/vf610-zii-cfu1.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-zii-cfu1.dts
@@ -68,8 +68,8 @@
 		pinctrl-0 = <&pinctrl_optical>;
 		pinctrl-names = "default";
 		i2c-bus = <&i2c0>;
-		los-gpio = <&gpio4 4 GPIO_ACTIVE_HIGH>;
-		tx-disable-gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>;
+		tx-disable-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
 	};
 
 	supply-voltage-monitor {
@@ -162,7 +162,7 @@
 		suppress-preamble;
 		status = "okay";
 
-		switch0: switch0@0 {
+		switch0: ethernet-switch@0 {
 			compatible = "marvell,mv88e6085";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_switch>;
@@ -173,26 +173,26 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 
-			ports {
+			ethernet-ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				port@0 {
+				ethernet-port@0 {
 					reg = <0>;
 					label = "eth_cu_1000_1";
 				};
 
-				port@1 {
+				ethernet-port@1 {
 					reg = <1>;
 					label = "eth_cu_1000_2";
 				};
 
-				port@2 {
+				ethernet-port@2 {
 					reg = <2>;
 					label = "eth_cu_1000_3";
 				};
 
-				port@5 {
+				ethernet-port@5 {
 					reg = <5>;
 					label = "eth_fc_1000_1";
 					phy-mode = "1000base-x";
@@ -200,9 +200,9 @@
 					sfp = <&sff>;
 				};
 
-				port@6 {
+				ethernet-port@6 {
 					reg = <6>;
-					label = "cpu";
+					phy-mode = "rmii";
 					ethernet = <&fec1>;
 
 					fixed-link {
@@ -333,7 +333,7 @@
 		>;
 	};
 
-	pinctrl_leds_debug: pinctrl-leds-debug {
+	pinctrl_leds_debug: pinctrl-leds-debuggrp {
 		fsl,pins = <
 			VF610_PAD_PTD3__GPIO_82			0x31c2
 			VF610_PAD_PTE3__GPIO_108		0x31c2
diff --git a/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts b/arch/arm/boot/dts/nxp/vf/vf610-zii-dev-rev-b.dts
index 1f9686c33a84..be6147239362 100644
--- a/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-zii-dev-rev-b.dts
@@ -75,7 +75,7 @@
 
 					port@6 {
 						reg = <6>;
-						label = "cpu";
+						phy-mode = "rmii";
 						ethernet = <&fec1>;
 
 						fixed-link {
@@ -288,17 +288,17 @@
 		};
 	};
 
-	spi0 {
+	spi-0 {
 		compatible = "spi-gpio";
 		pinctrl-0 = <&pinctrl_gpio_spi0>;
 		pinctrl-names = "default";
 		#address-cells = <1>;
 		#size-cells = <0>;
-		gpio-sck  = <&gpio1 12 GPIO_ACTIVE_HIGH>;
-		gpio-mosi = <&gpio1 11 GPIO_ACTIVE_HIGH>;
-		gpio-miso = <&gpio1 10 GPIO_ACTIVE_HIGH>;
-		cs-gpios  = <&gpio1  9 GPIO_ACTIVE_LOW
-			     &gpio1  8 GPIO_ACTIVE_HIGH>;
+		sck-gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
+		miso-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+		cs-gpios = <&gpio1 9 GPIO_ACTIVE_LOW
+			    &gpio1 8 GPIO_ACTIVE_HIGH>;
 		num-chipselects = <2>;
 
 		flash@0 {
@@ -338,6 +338,7 @@
 		reg = <0x22>;
 		gpio-controller;
 		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
 		interrupt-controller;
 		interrupt-parent = <&gpio3>;
 		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
@@ -345,7 +346,7 @@
 };
 
 &i2c2 {
-	tca9548@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		pinctrl-0 = <&pinctrl_i2c_mux_reset>;
 		pinctrl-names = "default";
@@ -411,13 +412,13 @@
 };
 
 &iomuxc {
-	pinctrl_gpio_e6185_eeprom_sel: pinctrl-gpio-e6185-eeprom-spi0 {
+	pinctrl_gpio_e6185_eeprom_sel: pinctrl-gpio-e6185-eeprom-spi0-grp {
 		fsl,pins = <
 			VF610_PAD_PTE27__GPIO_132	0x33e2
 		>;
 	};
 
-	pinctrl_gpio_spi0: pinctrl-gpio-spi0 {
+	pinctrl_gpio_spi0: pinctrl-gpio-spi0-grp {
 		fsl,pins = <
 			VF610_PAD_PTB22__GPIO_44	0x33e2
 			VF610_PAD_PTB21__GPIO_43	0x33e2
@@ -427,7 +428,7 @@
 		>;
 	};
 
-	pinctrl_mdio_mux: pinctrl-mdio-mux {
+	pinctrl_mdio_mux: pinctrl-mdio-mux-grp {
 		fsl,pins = <
 			VF610_PAD_PTA18__GPIO_8		0x31c2
 			VF610_PAD_PTA19__GPIO_9		0x31c2
@@ -436,7 +437,7 @@
 		>;
 	};
 
-	pinctrl_pca9554_22: pinctrl-pca95540-22 {
+	pinctrl_pca9554_22: pinctrl-pca95540-22-grp {
 		fsl,pins = <
 			VF610_PAD_PTB28__GPIO_98	0x219d
 		>;
diff --git a/arch/arm/boot/dts/vf610-zii-dev-rev-c.dts b/arch/arm/boot/dts/nxp/vf/vf610-zii-dev-rev-c.dts
index de79dcfd32e6..79ea7cf57a4d 100644
--- a/arch/arm/boot/dts/vf610-zii-dev-rev-c.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-zii-dev-rev-c.dts
@@ -44,7 +44,7 @@
 
 					port@0 {
 						reg = <0>;
-						label = "cpu";
+						phy-mode = "rmii";
 						ethernet = <&fec1>;
 
 						fixed-link {
@@ -82,6 +82,11 @@
 						label = "dsa";
 						phy-mode = "xaui";
 						link = <&switch1port10>;
+
+						fixed-link {
+							speed = <10000>;
+							full-duplex;
+						};
 					};
 				};
 
@@ -174,6 +179,11 @@
 						label = "dsa";
 						phy-mode = "xaui";
 						link = <&switch0port10>;
+
+						fixed-link {
+							speed = <10000>;
+							full-duplex;
+						};
 					};
 				};
 				mdio {
@@ -259,7 +269,7 @@
 		xtal-trim = /bits/ 8 <0x06>;
 
 		sleep-gpio = <&gpio0 24 GPIO_ACTIVE_HIGH>;
-		reset-gpio = <&gpio6 10 GPIO_ACTIVE_HIGH>;
+		reset-gpio = <&gpio6 10 GPIO_ACTIVE_LOW>;
 
 		fsl,spi-cs-sck-delay = <180>;
 		fsl,spi-sck-cs-delay = <250>;
@@ -301,7 +311,7 @@
 	 *    I/O14 - OPT1_TX_DIS
 	 *    I/O15 - OPT2_TX_DIS
 	 */
-	gpio6: sx1503@20 {
+	gpio6: pinctrl@20 {
 		compatible = "semtech,sx1503q";
 
 		pinctrl-names = "default";
@@ -340,7 +350,7 @@
 };
 
 &i2c2 {
-	tca9548@70 {
+	i2c-mux@70 {
 		compatible = "nxp,pca9548";
 		pinctrl-0 = <&pinctrl_i2c_mux_reset>;
 		pinctrl-names = "default";
@@ -382,7 +392,7 @@
 };
 
 &gpio0 {
-	eth0_intrp {
+	eth0-intrp-hog {
 		gpio-hog;
 		gpios = <23 GPIO_ACTIVE_HIGH>;
 		input;
@@ -391,7 +401,7 @@
 };
 
 &gpio3 {
-	eth0_intrp {
+	eth0-intrp-hog {
 		gpio-hog;
 		gpios = <2 GPIO_ACTIVE_HIGH>;
 		input;
@@ -419,7 +429,7 @@
 };
 
 &iomuxc {
-	pinctr_atzb_rf_233: pinctrl-atzb-rf-233 {
+	pinctr_atzb_rf_233: pinctrl-atzb-rf-233grp {
 		fsl,pins = <
 			VF610_PAD_PTB2__GPIO_24		0x31c2
 			VF610_PAD_PTE27__GPIO_132	0x33e2
@@ -427,7 +437,7 @@
 	};
 
 
-	pinctrl_sx1503_20: pinctrl-sx1503-20 {
+	pinctrl_sx1503_20: pinctrl-sx1503-20grp {
 		fsl,pins = <
 			VF610_PAD_PTB1__GPIO_23		0x219d
 		>;
@@ -440,7 +450,7 @@
 		>;
 	};
 
-	pinctrl_mdio_mux: pinctrl-mdio-mux {
+	pinctrl_mdio_mux: pinctrl-mdio-muxgrp {
 		fsl,pins = <
 			VF610_PAD_PTA18__GPIO_8		0x31c2
 			VF610_PAD_PTA19__GPIO_9		0x31c2
@@ -448,7 +458,7 @@
 		>;
 	};
 
-	pinctrl_fec0_phy_int: pinctrl-fec0-phy-int {
+	pinctrl_fec0_phy_int: pinctrl-fec0-phy-intgrp {
 		fsl,pins = <
 			VF610_PAD_PTB28__GPIO_98	0x219d
 		>;
diff --git a/arch/arm/boot/dts/vf610-zii-dev.dtsi b/arch/arm/boot/dts/nxp/vf/vf610-zii-dev.dtsi
index f8299f33a692..91cc496ffb90 100644
--- a/arch/arm/boot/dts/vf610-zii-dev.dtsi
+++ b/arch/arm/boot/dts/nxp/vf/vf610-zii-dev.dtsi
@@ -59,7 +59,7 @@
 		pinctrl-0 = <&pinctrl_leds_debug>;
 		pinctrl-names = "default";
 
-		debug {
+		led-debug {
 			label = "zii:green:debug1";
 			gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
@@ -335,7 +335,7 @@
 		>;
 	};
 
-	pinctrl_gpio_spi0: pinctrl-gpio-spi0 {
+	pinctrl_gpio_spi0: pinctrl-gpio-spi0-grp {
 		fsl,pins = <
 			VF610_PAD_PTB22__GPIO_44	0x33e2
 			VF610_PAD_PTB21__GPIO_43	0x33e2
@@ -345,19 +345,19 @@
 		>;
 	};
 
-	pinctrl_gpio_switch0: pinctrl-gpio-switch0 {
+	pinctrl_gpio_switch0: pinctrl-gpio-switch0-grp {
 		fsl,pins = <
 			VF610_PAD_PTB5__GPIO_27		0x219d
 		>;
 	};
 
-	pinctrl_gpio_switch1: pinctrl-gpio-switch1 {
+	pinctrl_gpio_switch1: pinctrl-gpio-switch1-grp {
 		fsl,pins = <
 			VF610_PAD_PTB4__GPIO_26		0x219d
 		>;
 	};
 
-	pinctrl_i2c_mux_reset: pinctrl-i2c-mux-reset {
+	pinctrl_i2c_mux_reset: pinctrl-i2c-mux-reset-grp {
 		fsl,pins = <
 			 VF610_PAD_PTE14__GPIO_119	0x31c2
 			 >;
@@ -370,7 +370,7 @@
 		>;
 	};
 
-	pinctrl_i2c0_gpio: i2c0grp-gpio {
+	pinctrl_i2c0_gpio: i2c0-gpio-grp {
 		fsl,pins = <
 			VF610_PAD_PTB14__GPIO_36	0x31c2
 			VF610_PAD_PTB15__GPIO_37	0x31c2
@@ -392,7 +392,7 @@
 		>;
 	};
 
-	pinctrl_leds_debug: pinctrl-leds-debug {
+	pinctrl_leds_debug: pinctrl-leds-debug-grp {
 		fsl,pins = <
 			 VF610_PAD_PTD20__GPIO_74	0x31c2
 			 >;
@@ -436,7 +436,7 @@
 		>;
 	};
 
-	pinctrl_usb_vbus: pinctrl-usb-vbus {
+	pinctrl_usb_vbus: pinctrl-usb-vbus-grp {
 		fsl,pins = <
 			VF610_PAD_PTA16__GPIO_6	0x31c2
 		>;
diff --git a/arch/arm/boot/dts/vf610-zii-scu4-aib.dts b/arch/arm/boot/dts/nxp/vf/vf610-zii-scu4-aib.dts
index 040a1f8b6130..8020a644dd9d 100644
--- a/arch/arm/boot/dts/vf610-zii-scu4-aib.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-zii-scu4-aib.dts
@@ -23,7 +23,7 @@
 		pinctrl-0 = <&pinctrl_leds_debug>;
 		pinctrl-names = "default";
 
-		debug {
+		led-debug {
 			label = "zii:green:debug1";
 			gpios = <&gpio3 0 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
@@ -47,19 +47,19 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			switch0: switch0@0 {
+			switch0: ethernet-switch@0 {
 				compatible = "marvell,mv88e6190";
 				reg = <0>;
 				dsa,member = <0 0>;
 				eeprom-length = <65536>;
 
-				ports {
+				ethernet-ports {
 					#address-cells = <1>;
 					#size-cells = <0>;
 
-					port@0 {
+					ethernet-port@0 {
 						reg = <0>;
-						label = "cpu";
+						phy-mode = "rmii";
 						ethernet = <&fec1>;
 
 						fixed-link {
@@ -68,37 +68,37 @@
 						};
 					};
 
-					port@1 {
+					ethernet-port@1 {
 						reg = <1>;
 						label = "aib2main_1";
 					};
 
-					port@2 {
+					ethernet-port@2 {
 						reg = <2>;
 						label = "aib2main_2";
 					};
 
-					port@3 {
+					ethernet-port@3 {
 						reg = <3>;
 						label = "eth_cu_1000_5";
 					};
 
-					port@4 {
+					ethernet-port@4 {
 						reg = <4>;
 						label = "eth_cu_1000_6";
 					};
 
-					port@5 {
+					ethernet-port@5 {
 						reg = <5>;
 						label = "eth_cu_1000_4";
 					};
 
-					port@6 {
+					ethernet-port@6 {
 						reg = <6>;
 						label = "eth_cu_1000_7";
 					};
 
-					port@7 {
+					ethernet-port@7 {
 						reg = <7>;
 						label = "modem_pic";
 
@@ -108,13 +108,18 @@
 						};
 					};
 
-					switch0port10: port@10 {
+					switch0port10: ethernet-port@10 {
 						reg = <10>;
 						label = "dsa";
 						phy-mode = "xgmii";
 						link = <&switch1port10
 							&switch3port10
 							&switch2port10>;
+
+						fixed-link {
+							speed = <10000>;
+							full-duplex;
+						};
 					};
 				};
 			};
@@ -125,44 +130,54 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			switch1: switch1@0 {
+			switch1: ethernet-switch@0 {
 				compatible = "marvell,mv88e6190";
 				reg = <0>;
 				dsa,member = <0 1>;
 				eeprom-length = <65536>;
 
-				ports {
+				ethernet-ports {
 					#address-cells = <1>;
 					#size-cells = <0>;
 
-					port@1 {
+					ethernet-port@1 {
 						reg = <1>;
 						label = "eth_cu_1000_3";
 					};
 
-					port@2 {
+					ethernet-port@2 {
 						reg = <2>;
 						label = "eth_cu_100_2";
 					};
 
-					port@3 {
+					ethernet-port@3 {
 						reg = <3>;
 						label = "eth_cu_100_3";
 					};
 
-					switch1port9: port@9 {
+					switch1port9: ethernet-port@9 {
 						reg = <9>;
 						label = "dsa";
 						phy-mode = "xgmii";
 						link = <&switch3port10
 							&switch2port10>;
+
+						fixed-link {
+							speed = <10000>;
+							full-duplex;
+						};
 					};
 
-					switch1port10: port@10 {
+					switch1port10: ethernet-port@10 {
 						reg = <10>;
 						label = "dsa";
 						phy-mode = "xgmii";
 						link = <&switch0port10>;
+
+						fixed-link {
+							speed = <10000>;
+							full-duplex;
+						};
 					};
 				};
 			};
@@ -173,17 +188,17 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			switch2: switch2@0 {
+			switch2: ethernet-switch@0 {
 				compatible = "marvell,mv88e6190";
 				reg = <0>;
 				dsa,member = <0 2>;
 				eeprom-length = <65536>;
 
-				ports {
+				ethernet-ports {
 					#address-cells = <1>;
 					#size-cells = <0>;
 
-					port@2 {
+					ethernet-port@2 {
 						reg = <2>;
 						label = "eth_fc_1000_2";
 						phy-mode = "1000base-x";
@@ -191,7 +206,7 @@
 						sfp = <&sff1>;
 					};
 
-					port@3 {
+					ethernet-port@3 {
 						reg = <3>;
 						label = "eth_fc_1000_3";
 						phy-mode = "1000base-x";
@@ -199,7 +214,7 @@
 						sfp = <&sff2>;
 					};
 
-					port@4 {
+					ethernet-port@4 {
 						reg = <4>;
 						label = "eth_fc_1000_4";
 						phy-mode = "1000base-x";
@@ -207,7 +222,7 @@
 						sfp = <&sff3>;
 					};
 
-					port@5 {
+					ethernet-port@5 {
 						reg = <5>;
 						label = "eth_fc_1000_5";
 						phy-mode = "1000base-x";
@@ -215,7 +230,7 @@
 						sfp = <&sff4>;
 					};
 
-					port@6 {
+					ethernet-port@6 {
 						reg = <6>;
 						label = "eth_fc_1000_6";
 						phy-mode = "1000base-x";
@@ -223,7 +238,7 @@
 						sfp = <&sff5>;
 					};
 
-					port@7 {
+					ethernet-port@7 {
 						reg = <7>;
 						label = "eth_fc_1000_7";
 						phy-mode = "1000base-x";
@@ -231,7 +246,7 @@
 						sfp = <&sff6>;
 					};
 
-					port@9 {
+					ethernet-port@9 {
 						reg = <9>;
 						label = "eth_fc_1000_1";
 						phy-mode = "1000base-x";
@@ -239,13 +254,18 @@
 						sfp = <&sff0>;
 					};
 
-					switch2port10: port@10 {
+					switch2port10: ethernet-port@10 {
 						reg = <10>;
 						label = "dsa";
 						phy-mode = "2500base-x";
 						link = <&switch3port9
 							&switch1port9
 							&switch0port10>;
+
+						fixed-link {
+							speed = <2500>;
+							full-duplex;
+						};
 					};
 				};
 			};
@@ -256,17 +276,17 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			switch3: switch3@0 {
+			switch3: ethernet-switch@0 {
 				compatible = "marvell,mv88e6190";
 				reg = <0>;
 				dsa,member = <0 3>;
 				eeprom-length = <65536>;
 
-				ports {
+				ethernet-ports {
 					#address-cells = <1>;
 					#size-cells = <0>;
 
-					port@2 {
+					ethernet-port@2 {
 						reg = <2>;
 						label = "eth_fc_1000_8";
 						phy-mode = "1000base-x";
@@ -274,7 +294,7 @@
 						sfp = <&sff7>;
 					};
 
-					port@3 {
+					ethernet-port@3 {
 						reg = <3>;
 						label = "eth_fc_1000_9";
 						phy-mode = "1000base-x";
@@ -282,7 +302,7 @@
 						sfp = <&sff8>;
 					};
 
-					port@4 {
+					ethernet-port@4 {
 						reg = <4>;
 						label = "eth_fc_1000_10";
 						phy-mode = "1000base-x";
@@ -290,19 +310,29 @@
 						sfp = <&sff9>;
 					};
 
-					switch3port9: port@9 {
+					switch3port9: ethernet-port@9 {
 						reg = <9>;
 						label = "dsa";
 						phy-mode = "2500base-x";
 						link = <&switch2port10>;
+
+						fixed-link {
+							speed = <2500>;
+							full-duplex;
+						};
 					};
 
-					switch3port10: port@10 {
+					switch3port10: ethernet-port@10 {
 						reg = <10>;
 						label = "dsa";
 						phy-mode = "xgmii";
 						link = <&switch1port9
 							&switch0port10>;
+
+						fixed-link {
+							speed = <10000>;
+							full-duplex;
+						};
 					};
 				};
 			};
@@ -553,7 +583,7 @@
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
 
-	gpio9: io-expander@20 {
+	gpio9: pinctrl@20 {
 		compatible = "semtech,sx1503q";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_sx1503_20>;
@@ -593,7 +623,6 @@
 
 	i2c-mux@70 {
 		compatible = "nxp,pca9548";
-		pinctrl-names = "default";
 		#address-cells = <1>;
 		#size-cells = <0>;
 		reg = <0x70>;
@@ -632,7 +661,6 @@
 
 	i2c-mux@71 {
 		compatible = "nxp,pca9548";
-		pinctrl-names = "default";
 		reg = <0x71>;
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -717,7 +745,7 @@
 		>;
 	};
 
-	pinctrl_dspi2: dspi2gpio {
+	pinctrl_dspi2: dspi2gpiogrp {
 		fsl,pins = <
 			VF610_PAD_PTD30__GPIO_64		0x33e2
 			VF610_PAD_PTD29__GPIO_65		0x33e1
@@ -789,13 +817,13 @@
 		>;
 	};
 
-	pinctrl_leds_debug: pinctrl-leds-debug {
+	pinctrl_leds_debug: pinctrl-leds-debuggrp {
 		fsl,pins = <
 			 VF610_PAD_PTB26__GPIO_96		0x31c2
 		   >;
 	};
 
-	pinctrl_mdio_mux: pinctrl-mdio-mux {
+	pinctrl_mdio_mux: pinctrl-mdio-muxgrp {
 		fsl,pins = <
 			VF610_PAD_PTE27__GPIO_132		0x31c2
 			VF610_PAD_PTE28__GPIO_133		0x31c2
@@ -815,7 +843,7 @@
 		>;
 	};
 
-	pinctrl_sx1503_20: pinctrl-sx1503-20 {
+	pinctrl_sx1503_20: pinctrl-sx1503-20grp {
 		fsl,pins = <
 			VF610_PAD_PTD31__GPIO_63		0x219d
 			>;
diff --git a/arch/arm/boot/dts/vf610-zii-spb4.dts b/arch/arm/boot/dts/nxp/vf/vf610-zii-spb4.dts
index 6c6ec46fd015..423d185c971f 100644
--- a/arch/arm/boot/dts/vf610-zii-spb4.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-zii-spb4.dts
@@ -123,7 +123,7 @@
 		suppress-preamble;
 		status = "okay";
 
-		switch0: switch0@0 {
+		switch0: ethernet-switch@0 {
 			compatible = "marvell,mv88e6190";
 			pinctrl-0 = <&pinctrl_gpio_switch0>;
 			pinctrl-names = "default";
@@ -134,13 +134,13 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 
-			ports {
+			ethernet-ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				port@0 {
+				ethernet-port@0 {
 					reg = <0>;
-					label = "cpu";
+					phy-mode = "rmii";
 					ethernet = <&fec1>;
 
 					fixed-link {
@@ -149,32 +149,32 @@
 					};
 				};
 
-				port@1 {
+				ethernet-port@1 {
 					reg = <1>;
 					label = "eth_cu_1000_1";
 				};
 
-				port@2 {
+				ethernet-port@2 {
 					reg = <2>;
 					label = "eth_cu_1000_2";
 				};
 
-				port@3 {
+				ethernet-port@3 {
 					reg = <3>;
 					label = "eth_cu_1000_3";
 				};
 
-				port@4 {
+				ethernet-port@4 {
 					reg = <4>;
 					label = "eth_cu_1000_4";
 				};
 
-				port@5 {
+				ethernet-port@5 {
 					reg = <5>;
 					label = "eth_cu_1000_5";
 				};
 
-				port@6 {
+				ethernet-port@6 {
 					reg = <6>;
 					label = "eth_cu_1000_6";
 				};
@@ -241,7 +241,7 @@
 	pinctrl-0 = <&pinctrl_uart2>;
 	status = "okay";
 
-	rave-sp {
+	mcu {
 		compatible = "zii,rave-sp-rdu2";
 		current-speed = <1000000>;
 		#address-cells = <1>;
@@ -323,7 +323,7 @@
 		>;
 	};
 
-	pinctrl_gpio_switch0: pinctrl-gpio-switch0 {
+	pinctrl_gpio_switch0: pinctrl-gpio-switch0grp {
 		fsl,pins = <
 			VF610_PAD_PTB28__GPIO_98		0x219d
 		>;
@@ -343,7 +343,7 @@
 		>;
 	};
 
-	pinctrl_leds_debug: pinctrl-leds-debug {
+	pinctrl_leds_debug: pinctrl-leds-debuggrp {
 		fsl,pins = <
 			VF610_PAD_PTD3__GPIO_82			0x31c2
 		>;
diff --git a/arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts b/arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-dtu.dts
index 73fdace4cb42..d5c7f710c314 100644
--- a/arch/arm/boot/dts/vf610-zii-ssmb-dtu.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-dtu.dts
@@ -112,7 +112,7 @@
 		suppress-preamble;
 		status = "okay";
 
-		switch0: switch0@0 {
+		switch0: ethernet-switch@0 {
 			compatible = "marvell,mv88e6190";
 			pinctrl-0 = <&pinctrl_gpio_switch0>;
 			pinctrl-names = "default";
@@ -123,13 +123,13 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 
-			ports {
+			ethernet-ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				port@0 {
+				ethernet-port@0 {
 					reg = <0>;
-					label = "cpu";
+					phy-mode = "rmii";
 					ethernet = <&fec1>;
 
 					fixed-link {
@@ -138,27 +138,27 @@
 					};
 				};
 
-				port@1 {
+				ethernet-port@1 {
 					reg = <1>;
 					label = "eth_cu_100_3";
 				};
 
-				port@5 {
+				ethernet-port@5 {
 					reg = <5>;
 					label = "eth_cu_1000_4";
 				};
 
-				port@6 {
+				ethernet-port@6 {
 					reg = <6>;
 					label = "eth_cu_1000_5";
 				};
 
-				port@8 {
+				ethernet-port@8 {
 					reg = <8>;
 					label = "eth_cu_1000_1";
 				};
 
-				port@9 {
+				ethernet-port@9 {
 					reg = <9>;
 					label = "eth_cu_1000_2";
 					phy-handle = <&phy9>;
@@ -167,12 +167,12 @@
 				};
 			};
 
-			mdio1 {
+			mdio-external {
 				compatible = "marvell,mv88e6xxx-mdio-external";
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				phy9: phy9@0 {
+				phy9: ethernet-phy@0 {
 					compatible = "ethernet-phy-ieee802.3-c45";
 					pinctrl-0 = <&pinctrl_gpio_phy9>;
 					pinctrl-names = "default";
@@ -284,13 +284,13 @@
 		>;
 	};
 
-	pinctrl_gpio_phy9: pinctrl-gpio-phy9 {
+	pinctrl_gpio_phy9: pinctrl-gpio-phy9grp {
 		fsl,pins = <
 			VF610_PAD_PTB24__GPIO_94		0x219d
 		>;
 	};
 
-	pinctrl_gpio_switch0: pinctrl-gpio-switch0 {
+	pinctrl_gpio_switch0: pinctrl-gpio-switch0grp {
 		fsl,pins = <
 			VF610_PAD_PTB28__GPIO_98		0x219d
 		>;
@@ -310,7 +310,7 @@
 		>;
 	};
 
-	pinctrl_leds_debug: pinctrl-leds-debug {
+	pinctrl_leds_debug: pinctrl-leds-debuggrp {
 		fsl,pins = <
 			VF610_PAD_PTD3__GPIO_82			0x31c2
 		>;
diff --git a/arch/arm/boot/dts/vf610-zii-ssmb-spu3.dts b/arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-spu3.dts
index fe600ab2e4bd..344cc2b4d0ad 100644
--- a/arch/arm/boot/dts/vf610-zii-ssmb-spu3.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-spu3.dts
@@ -137,7 +137,7 @@
 		suppress-preamble;
 		status = "okay";
 
-		switch0: switch0@0 {
+		switch0: ethernet-switch@0 {
 			compatible = "marvell,mv88e6190";
 			pinctrl-0 = <&pinctrl_gpio_switch0>;
 			pinctrl-names = "default";
@@ -148,13 +148,13 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 
-			ports {
+			ethernet-ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				port@0 {
+				ethernet-port@0 {
 					reg = <0>;
-					label = "cpu";
+					phy-mode = "rmii";
 					ethernet = <&fec1>;
 
 					fixed-link {
@@ -163,32 +163,32 @@
 					};
 				};
 
-				port@1 {
+				ethernet-port@1 {
 					reg = <1>;
 					label = "eth_cu_1000_1";
 				};
 
-				port@2 {
+				ethernet-port@2 {
 					reg = <2>;
 					label = "eth_cu_1000_2";
 				};
 
-				port@3 {
+				ethernet-port@3 {
 					reg = <3>;
 					label = "eth_cu_1000_3";
 				};
 
-				port@4 {
+				ethernet-port@4 {
 					reg = <4>;
 					label = "eth_cu_1000_4";
 				};
 
-				port@5 {
+				ethernet-port@5 {
 					reg = <5>;
 					label = "eth_cu_1000_5";
 				};
 
-				port@6 {
+				ethernet-port@6 {
 					reg = <6>;
 					label = "eth_cu_1000_6";
 				};
@@ -254,7 +254,7 @@
 	pinctrl-0 = <&pinctrl_uart1>;
 	status = "okay";
 
-	rave-sp {
+	mcu {
 		compatible = "zii,rave-sp-rdu2";
 		current-speed = <1000000>;
 		#address-cells = <1>;
@@ -330,7 +330,7 @@
 		>;
 	};
 
-	pinctrl_gpio_switch0: pinctrl-gpio-switch0 {
+	pinctrl_gpio_switch0: pinctrl-gpio-switch0grp {
 		fsl,pins = <
 			VF610_PAD_PTB28__GPIO_98		0x219d
 		>;
@@ -350,7 +350,7 @@
 		>;
 	};
 
-	pinctrl_leds_debug: pinctrl-leds-debug {
+	pinctrl_leds_debug: pinctrl-leds-debuggrp {
 		fsl,pins = <
 			VF610_PAD_PTD3__GPIO_82			0x31c2
 		>;
diff --git a/arch/arm/boot/dts/vf610.dtsi b/arch/arm/boot/dts/nxp/vf/vf610.dtsi
index 956182d08e74..2fba923821d0 100644
--- a/arch/arm/boot/dts/vf610.dtsi
+++ b/arch/arm/boot/dts/nxp/vf/vf610.dtsi
@@ -2,7 +2,6 @@
 //
 // Copyright 2013 Freescale Semiconductor, Inc.
 
-
 #include "vf500.dtsi"
 
 &a5_cpu {
diff --git a/arch/arm/boot/dts/vf610m4-colibri.dts b/arch/arm/boot/dts/nxp/vf/vf610m4-colibri.dts
index 2c2db47af441..86d32f54c250 100644
--- a/arch/arm/boot/dts/vf610m4-colibri.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610m4-colibri.dts
@@ -50,14 +50,12 @@
 };
 
 &iomuxc {
-	vf610-colibri {
-		pinctrl_uart2: uart2grp {
-			fsl,pins = <
-				VF610_PAD_PTD0__UART2_TX		0x21a2
-				VF610_PAD_PTD1__UART2_RX		0x21a1
-				VF610_PAD_PTD2__UART2_RTS		0x21a2
-				VF610_PAD_PTD3__UART2_CTS		0x21a1
-			>;
-		};
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			VF610_PAD_PTD0__UART2_TX		0x21a2
+			VF610_PAD_PTD1__UART2_RX		0x21a1
+			VF610_PAD_PTD2__UART2_RTS		0x21a2
+			VF610_PAD_PTD3__UART2_CTS		0x21a1
+		>;
 	};
 };
diff --git a/arch/arm/boot/dts/vf610m4-cosmic.dts b/arch/arm/boot/dts/nxp/vf/vf610m4-cosmic.dts
index f7474c11aabd..454b484368cb 100644
--- a/arch/arm/boot/dts/vf610m4-cosmic.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610m4-cosmic.dts
@@ -79,12 +79,10 @@
 };
 
 &iomuxc {
-	vf610-cosmic {
-		pinctrl_uart3: uart3grp {
-			fsl,pins = <
-				VF610_PAD_PTA20__UART3_TX		0x21a2
-				VF610_PAD_PTA21__UART3_RX		0x21a1
-			>;
-		};
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			VF610_PAD_PTA20__UART3_TX		0x21a2
+			VF610_PAD_PTA21__UART3_RX		0x21a1
+		>;
 	};
 };
diff --git a/arch/arm/boot/dts/vf610m4.dtsi b/arch/arm/boot/dts/nxp/vf/vf610m4.dtsi
index 76bbfd5e32b6..648d219e1d0e 100644
--- a/arch/arm/boot/dts/vf610m4.dtsi
+++ b/arch/arm/boot/dts/nxp/vf/vf610m4.dtsi
@@ -42,7 +42,7 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
-#include "armv7-m.dtsi"
+#include "../../armv7-m.dtsi"
 #include "vfxxx.dtsi"
 
 / {
@@ -55,3 +55,7 @@
 &mscm_ir {
 	interrupt-parent = <&nvic>;
 };
+
+&nvic {
+	arm,num-irq-priority-bits = <4>;
+};
diff --git a/arch/arm/boot/dts/vfxxx.dtsi b/arch/arm/boot/dts/nxp/vf/vfxxx.dtsi
index d53f9c9db8bf..568d81807c81 100644
--- a/arch/arm/boot/dts/vfxxx.dtsi
+++ b/arch/arm/boot/dts/nxp/vf/vfxxx.dtsi
@@ -111,8 +111,7 @@
 				interrupts = <61 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks VF610_CLK_UART0>;
 				clock-names = "ipg";
-				dmas = <&edma0 0 2>,
-					<&edma0 0 3>;
+				dmas = <&edma0 0 2>, <&edma0 0 3>;
 				dma-names = "rx","tx";
 				status = "disabled";
 			};
@@ -123,8 +122,7 @@
 				interrupts = <62 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks VF610_CLK_UART1>;
 				clock-names = "ipg";
-				dmas = <&edma0 0 4>,
-					<&edma0 0 5>;
+				dmas = <&edma0 0 4>, <&edma0 0 5>;
 				dma-names = "rx","tx";
 				status = "disabled";
 			};
@@ -135,8 +133,7 @@
 				interrupts = <63 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks VF610_CLK_UART2>;
 				clock-names = "ipg";
-				dmas = <&edma0 0 6>,
-					<&edma0 0 7>;
+				dmas = <&edma0 0 6>, <&edma0 0 7>;
 				dma-names = "rx","tx";
 				status = "disabled";
 			};
@@ -147,8 +144,7 @@
 				interrupts = <64 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks VF610_CLK_UART3>;
 				clock-names = "ipg";
-				dmas = <&edma0 0 8>,
-					<&edma0 0 9>;
+				dmas = <&edma0 0 8>, <&edma0 0 9>;
 				dma-names = "rx","tx";
 				status = "disabled";
 			};
@@ -162,9 +158,8 @@
 				clocks = <&clks VF610_CLK_DSPI0>;
 				clock-names = "dspi";
 				spi-num-chipselects = <6>;
-				dmas = <&edma1 1 12>,
-					<&edma1 1 13>;
-				dma-names = "rx", "tx";
+				dmas = <&edma1 1 13>, <&edma1 1 12>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -177,9 +172,8 @@
 				clocks = <&clks VF610_CLK_DSPI1>;
 				clock-names = "dspi";
 				spi-num-chipselects = <4>;
-				dmas = <&edma1 1 14>,
-					<&edma1 1 15>;
-				dma-names = "rx", "tx";
+				dmas = <&edma1 1 15>, <&edma1 1 14>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -191,9 +185,8 @@
 					<&clks VF610_CLK_SAI0_DIV>,
 					<&clks 0>, <&clks 0>;
 				clock-names = "bus", "mclk1", "mclk2", "mclk3";
-				dma-names = "tx", "rx";
-				dmas = <&edma0 0 17>,
-					<&edma0 0 16>;
+				dma-names = "rx", "tx";
+				dmas = <&edma0 0 16>, <&edma0 0 17>;
 				status = "disabled";
 			};
 
@@ -205,9 +198,8 @@
 					<&clks VF610_CLK_SAI1_DIV>,
 					<&clks 0>, <&clks 0>;
 				clock-names = "bus", "mclk1", "mclk2", "mclk3";
-				dma-names = "tx", "rx";
-				dmas = <&edma0 0 19>,
-					<&edma0 0 18>;
+				dma-names = "rx", "tx";
+				dmas = <&edma0 0 18>, <&edma0 0 19>;
 				status = "disabled";
 			};
 
@@ -219,9 +211,8 @@
 					<&clks VF610_CLK_SAI2_DIV>,
 					<&clks 0>, <&clks 0>;
 				clock-names = "bus", "mclk1", "mclk2", "mclk3";
-				dma-names = "tx", "rx";
-				dmas = <&edma0 0 21>,
-					<&edma0 0 20>;
+				dma-names = "rx", "tx";
+				dmas = <&edma0 0 20>, <&edma0 0 21>;
 				status = "disabled";
 			};
 
@@ -233,9 +224,8 @@
 					<&clks VF610_CLK_SAI3_DIV>,
 					<&clks 0>, <&clks 0>;
 				clock-names = "bus", "mclk1", "mclk2", "mclk3";
-				dma-names = "tx", "rx";
-				dmas = <&edma0 1 9>,
-					<&edma0 1 8>;
+				dma-names = "rx", "tx";
+				dmas = <&edma0 1 8>, <&edma0 1 9>;
 				status = "disabled";
 			};
 
@@ -298,7 +288,6 @@
 				reg = <0x4003e000 0x1000>;
 				interrupts = <20 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks VF610_CLK_WDT>;
-				clock-names = "wdog";
 				status = "disabled";
 			};
 
@@ -315,7 +304,7 @@
 				status = "disabled";
 			};
 
-			iomuxc: iomuxc@40048000 {
+			iomuxc: pinctrl@40048000 {
 				compatible = "fsl,vf610-iomuxc";
 				reg = <0x40048000 0x1000>;
 			};
@@ -329,6 +318,7 @@
 				interrupt-controller;
 				#interrupt-cells = <2>;
 				gpio-ranges = <&iomuxc 0 0 32>;
+				ngpios = <32>;
 			};
 
 			gpio1: gpio@4004a000 {
@@ -340,6 +330,7 @@
 				interrupt-controller;
 				#interrupt-cells = <2>;
 				gpio-ranges = <&iomuxc 0 32 32>;
+				ngpios = <32>;
 			};
 
 			gpio2: gpio@4004b000 {
@@ -351,6 +342,7 @@
 				interrupt-controller;
 				#interrupt-cells = <2>;
 				gpio-ranges = <&iomuxc 0 64 32>;
+				ngpios = <32>;
 			};
 
 			gpio3: gpio@4004c000 {
@@ -362,6 +354,7 @@
 				interrupt-controller;
 				#interrupt-cells = <2>;
 				gpio-ranges = <&iomuxc 0 96 32>;
+				ngpios = <32>;
 			};
 
 			gpio4: gpio@4004d000 {
@@ -373,6 +366,7 @@
 				interrupt-controller;
 				#interrupt-cells = <2>;
 				gpio-ranges = <&iomuxc 0 128 7>;
+				ngpios = <7>;
 			};
 
 			anatop: anatop@40050000 {
@@ -431,8 +425,7 @@
 				interrupts = <72 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks VF610_CLK_I2C1>;
 				clock-names = "ipg";
-				dmas = <&edma0 0 52>,
-					<&edma0 0 53>;
+				dmas = <&edma0 0 52>, <&edma0 0 53>;
 				dma-names = "rx","tx";
 				status = "disabled";
 			};
@@ -541,9 +534,8 @@
 				clocks = <&clks VF610_CLK_DSPI2>;
 				clock-names = "dspi";
 				spi-num-chipselects = <2>;
-				dmas = <&edma1 0 10>,
-					<&edma1 0 11>;
-				dma-names = "rx", "tx";
+				dmas = <&edma1 0 11>, <&edma1 0 10>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -556,9 +548,8 @@
 				clocks = <&clks VF610_CLK_DSPI3>;
 				clock-names = "dspi";
 				spi-num-chipselects = <2>;
-				dmas = <&edma1 0 12>,
-					<&edma1 0 13>;
-				dma-names = "rx", "tx";
+				dmas = <&edma1 0 13>, <&edma1 0 12>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -574,7 +565,7 @@
 							<20000000>;
 			};
 
-			esdhc0: esdhc@400b1000 {
+			esdhc0: mmc@400b1000 {
 				compatible = "fsl,imx53-esdhc";
 				reg = <0x400b1000 0x1000>;
 				interrupts = <27 IRQ_TYPE_LEVEL_HIGH>;
@@ -585,7 +576,7 @@
 				status = "disabled";
 			};
 
-			esdhc1: esdhc@400b2000 {
+			esdhc1: mmc@400b2000 {
 				compatible = "fsl,imx53-esdhc";
 				reg = <0x400b2000 0x1000>;
 				interrupts = <28 IRQ_TYPE_LEVEL_HIGH>;
@@ -617,7 +608,7 @@
 
 			ftm: ftm@400b8000 {
 				compatible = "fsl,ftm-timer";
-				reg = <0x400b8000 0x1000 0x400b9000 0x1000>;
+				reg = <0x400b8000 0x1000>, <0x400b9000 0x1000>;
 				interrupts = <44 IRQ_TYPE_LEVEL_HIGH>;
 				clock-names = "ftm-evt", "ftm-src",
 					"ftm-evt-counter-en", "ftm-src-counter-en";
@@ -691,7 +682,7 @@
 				status = "disabled";
 			};
 
-			nfc: nand@400e0000 {
+			nfc: nand-controller@400e0000 {
 				#address-cells = <1>;
 				#size-cells = <0>;
 				compatible = "fsl,vf610-nfc";
@@ -724,8 +715,7 @@
 				interrupts = <74 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks VF610_CLK_I2C3>;
 				clock-names = "ipg";
-				dmas = <&edma0 1 38>,
-					<&edma0 1 39>;
+				dmas = <&edma0 1 38>, <&edma0 1 39>;
 				dma-names = "rx","tx";
 				status = "disabled";
 			};
@@ -739,13 +729,13 @@
 				clocks = <&clks VF610_CLK_CAAM>;
 				clock-names = "ipg";
 
-				sec_jr0: jr0@1000 {
+				sec_jr0: jr@1000 {
 					compatible = "fsl,sec-v4.0-job-ring";
 					reg = <0x1000 0x1000>;
 					interrupts = <102 IRQ_TYPE_LEVEL_HIGH>;
 				};
 
-				sec_jr1: jr1@2000 {
+				sec_jr1: jr@2000 {
 					compatible = "fsl,sec-v4.0-job-ring";
 					reg = <0x2000 0x1000>;
 					interrupts = <102 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/omap34xx-omap36xx-clocks.dtsi b/arch/arm/boot/dts/omap34xx-omap36xx-clocks.dtsi
deleted file mode 100644
index 21079cdf2663..000000000000
--- a/arch/arm/boot/dts/omap34xx-omap36xx-clocks.dtsi
+++ /dev/null
@@ -1,265 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Device Tree Source for OMAP34XX/OMAP36XX clock data
- *
- * Copyright (C) 2013 Texas Instruments, Inc.
- */
-&cm_clocks {
-	security_l4_ick2: security_l4_ick2 {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&l4_ick>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	aes1_ick: aes1_ick@a14 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&security_l4_ick2>;
-		ti,bit-shift = <3>;
-		reg = <0x0a14>;
-	};
-
-	rng_ick: rng_ick@a14 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&security_l4_ick2>;
-		reg = <0x0a14>;
-		ti,bit-shift = <2>;
-	};
-
-	sha11_ick: sha11_ick@a14 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&security_l4_ick2>;
-		reg = <0x0a14>;
-		ti,bit-shift = <1>;
-	};
-
-	des1_ick: des1_ick@a14 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&security_l4_ick2>;
-		reg = <0x0a14>;
-		ti,bit-shift = <0>;
-	};
-
-	cam_mclk: cam_mclk@f00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&dpll4_m5x2_ck>;
-		ti,bit-shift = <0>;
-		reg = <0x0f00>;
-		ti,set-rate-parent;
-	};
-
-	cam_ick: cam_ick@f10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-no-wait-interface-clock";
-		clocks = <&l4_ick>;
-		reg = <0x0f10>;
-		ti,bit-shift = <0>;
-	};
-
-	csi2_96m_fck: csi2_96m_fck@f00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&core_96m_fck>;
-		reg = <0x0f00>;
-		ti,bit-shift = <1>;
-	};
-
-	security_l3_ick: security_l3_ick {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&l3_ick>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	pka_ick: pka_ick@a14 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&security_l3_ick>;
-		reg = <0x0a14>;
-		ti,bit-shift = <4>;
-	};
-
-	icr_ick: icr_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <29>;
-	};
-
-	des2_ick: des2_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <26>;
-	};
-
-	mspro_ick: mspro_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <23>;
-	};
-
-	mailboxes_ick: mailboxes_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <7>;
-	};
-
-	ssi_l4_ick: ssi_l4_ick {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&l4_ick>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	sr1_fck: sr1_fck@c00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&sys_ck>;
-		reg = <0x0c00>;
-		ti,bit-shift = <6>;
-	};
-
-	sr2_fck: sr2_fck@c00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&sys_ck>;
-		reg = <0x0c00>;
-		ti,bit-shift = <7>;
-	};
-
-	sr_l4_ick: sr_l4_ick {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&l4_ick>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	dpll2_fck: dpll2_fck@40 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&core_ck>;
-		ti,bit-shift = <19>;
-		ti,max-div = <7>;
-		reg = <0x0040>;
-		ti,index-starts-at-one;
-	};
-
-	dpll2_ck: dpll2_ck@4 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-dpll-clock";
-		clocks = <&sys_ck>, <&dpll2_fck>;
-		reg = <0x0004>, <0x0024>, <0x0040>, <0x0034>;
-		ti,low-power-stop;
-		ti,lock;
-		ti,low-power-bypass;
-	};
-
-	dpll2_m2_ck: dpll2_m2_ck@44 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&dpll2_ck>;
-		ti,max-div = <31>;
-		reg = <0x0044>;
-		ti,index-starts-at-one;
-	};
-
-	iva2_ck: iva2_ck@0 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&dpll2_m2_ck>;
-		reg = <0x0000>;
-		ti,bit-shift = <0>;
-	};
-
-	modem_fck: modem_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&sys_ck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <31>;
-	};
-
-	sad2d_ick: sad2d_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&l3_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <3>;
-	};
-
-	mad2d_ick: mad2d_ick@a18 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&l3_ick>;
-		reg = <0x0a18>;
-		ti,bit-shift = <3>;
-	};
-
-	mspro_fck: mspro_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_96m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <23>;
-	};
-};
-
-&cm_clockdomains {
-	cam_clkdm: cam_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&cam_ick>, <&csi2_96m_fck>;
-	};
-
-	iva2_clkdm: iva2_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&iva2_ck>;
-	};
-
-	dpll2_clkdm: dpll2_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&dpll2_ck>;
-	};
-
-	wkup_clkdm: wkup_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&gpio1_dbck>, <&wdt2_fck>, <&wdt2_ick>, <&wdt1_ick>,
-			 <&gpio1_ick>, <&omap_32ksync_ick>, <&gpt12_ick>,
-			 <&gpt1_ick>, <&sr1_fck>, <&sr2_fck>;
-	};
-
-	d2d_clkdm: d2d_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&modem_fck>, <&sad2d_ick>, <&mad2d_ick>;
-	};
-
-	core_l4_clkdm: core_l4_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&mmchs2_fck>, <&mmchs1_fck>, <&i2c3_fck>, <&i2c2_fck>,
-			 <&i2c1_fck>, <&mcspi4_fck>, <&mcspi3_fck>,
-			 <&mcspi2_fck>, <&mcspi1_fck>, <&uart2_fck>,
-			 <&uart1_fck>, <&hdq_fck>, <&mmchs2_ick>, <&mmchs1_ick>,
-			 <&hdq_ick>, <&mcspi4_ick>, <&mcspi3_ick>,
-			 <&mcspi2_ick>, <&mcspi1_ick>, <&i2c3_ick>, <&i2c2_ick>,
-			 <&i2c1_ick>, <&uart2_ick>, <&uart1_ick>, <&gpt11_ick>,
-			 <&gpt10_ick>, <&mcbsp5_ick>, <&mcbsp1_ick>,
-			 <&omapctrl_ick>, <&aes2_ick>, <&sha12_ick>, <&icr_ick>,
-			 <&des2_ick>, <&mspro_ick>, <&mailboxes_ick>,
-			 <&rng_ick>, <&mspro_fck>;
-	};
-};
diff --git a/arch/arm/boot/dts/omap3xxx-clocks.dtsi b/arch/arm/boot/dts/omap3xxx-clocks.dtsi
deleted file mode 100644
index 0656c32439d2..000000000000
--- a/arch/arm/boot/dts/omap3xxx-clocks.dtsi
+++ /dev/null
@@ -1,1662 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Device Tree Source for OMAP3 clock data
- *
- * Copyright (C) 2013 Texas Instruments, Inc.
- */
-&prm_clocks {
-	virt_16_8m_ck: virt_16_8m_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <16800000>;
-	};
-
-	osc_sys_ck: osc_sys_ck@d40 {
-		#clock-cells = <0>;
-		compatible = "ti,mux-clock";
-		clocks = <&virt_12m_ck>, <&virt_13m_ck>, <&virt_19200000_ck>, <&virt_26000000_ck>, <&virt_38_4m_ck>, <&virt_16_8m_ck>;
-		reg = <0x0d40>;
-	};
-
-	sys_ck: sys_ck@1270 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&osc_sys_ck>;
-		ti,bit-shift = <6>;
-		ti,max-div = <3>;
-		reg = <0x1270>;
-		ti,index-starts-at-one;
-	};
-
-	sys_clkout1: sys_clkout1@d70 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&osc_sys_ck>;
-		reg = <0x0d70>;
-		ti,bit-shift = <7>;
-	};
-
-	dpll3_x2_ck: dpll3_x2_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll3_ck>;
-		clock-mult = <2>;
-		clock-div = <1>;
-	};
-
-	dpll3_m2x2_ck: dpll3_m2x2_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll3_m2_ck>;
-		clock-mult = <2>;
-		clock-div = <1>;
-	};
-
-	dpll4_x2_ck: dpll4_x2_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll4_ck>;
-		clock-mult = <2>;
-		clock-div = <1>;
-	};
-
-	corex2_fck: corex2_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll3_m2x2_ck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	wkup_l4_ick: wkup_l4_ick {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&sys_ck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-};
-
-&scm_clocks {
-	mcbsp5_mux_fck: mcbsp5_mux_fck@68 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&core_96m_fck>, <&mcbsp_clks>;
-		ti,bit-shift = <4>;
-		reg = <0x68>;
-	};
-
-	mcbsp5_fck: mcbsp5_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&mcbsp5_gate_fck>, <&mcbsp5_mux_fck>;
-	};
-
-	mcbsp1_mux_fck: mcbsp1_mux_fck@4 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&core_96m_fck>, <&mcbsp_clks>;
-		ti,bit-shift = <2>;
-		reg = <0x04>;
-	};
-
-	mcbsp1_fck: mcbsp1_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&mcbsp1_gate_fck>, <&mcbsp1_mux_fck>;
-	};
-
-	mcbsp2_mux_fck: mcbsp2_mux_fck@4 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&per_96m_fck>, <&mcbsp_clks>;
-		ti,bit-shift = <6>;
-		reg = <0x04>;
-	};
-
-	mcbsp2_fck: mcbsp2_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&mcbsp2_gate_fck>, <&mcbsp2_mux_fck>;
-	};
-
-	mcbsp3_mux_fck: mcbsp3_mux_fck@68 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&per_96m_fck>, <&mcbsp_clks>;
-		reg = <0x68>;
-	};
-
-	mcbsp3_fck: mcbsp3_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&mcbsp3_gate_fck>, <&mcbsp3_mux_fck>;
-	};
-
-	mcbsp4_mux_fck: mcbsp4_mux_fck@68 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&per_96m_fck>, <&mcbsp_clks>;
-		ti,bit-shift = <2>;
-		reg = <0x68>;
-	};
-
-	mcbsp4_fck: mcbsp4_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&mcbsp4_gate_fck>, <&mcbsp4_mux_fck>;
-	};
-};
-&cm_clocks {
-	dummy_apb_pclk: dummy_apb_pclk {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <0x0>;
-	};
-
-	omap_32k_fck: omap_32k_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <32768>;
-	};
-
-	virt_12m_ck: virt_12m_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <12000000>;
-	};
-
-	virt_13m_ck: virt_13m_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <13000000>;
-	};
-
-	virt_19200000_ck: virt_19200000_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <19200000>;
-	};
-
-	virt_26000000_ck: virt_26000000_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <26000000>;
-	};
-
-	virt_38_4m_ck: virt_38_4m_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <38400000>;
-	};
-
-	dpll4_ck: dpll4_ck@d00 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-dpll-per-clock";
-		clocks = <&sys_ck>, <&sys_ck>;
-		reg = <0x0d00>, <0x0d20>, <0x0d44>, <0x0d30>;
-	};
-
-	dpll4_m2_ck: dpll4_m2_ck@d48 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&dpll4_ck>;
-		ti,max-div = <63>;
-		reg = <0x0d48>;
-		ti,index-starts-at-one;
-	};
-
-	dpll4_m2x2_mul_ck: dpll4_m2x2_mul_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll4_m2_ck>;
-		clock-mult = <2>;
-		clock-div = <1>;
-	};
-
-	dpll4_m2x2_ck: dpll4_m2x2_ck@d00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&dpll4_m2x2_mul_ck>;
-		ti,bit-shift = <0x1b>;
-		reg = <0x0d00>;
-		ti,set-bit-to-disable;
-	};
-
-	omap_96m_alwon_fck: omap_96m_alwon_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll4_m2x2_ck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	dpll3_ck: dpll3_ck@d00 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-dpll-core-clock";
-		clocks = <&sys_ck>, <&sys_ck>;
-		reg = <0x0d00>, <0x0d20>, <0x0d40>, <0x0d30>;
-	};
-
-	dpll3_m3_ck: dpll3_m3_ck@1140 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&dpll3_ck>;
-		ti,bit-shift = <16>;
-		ti,max-div = <31>;
-		reg = <0x1140>;
-		ti,index-starts-at-one;
-	};
-
-	dpll3_m3x2_mul_ck: dpll3_m3x2_mul_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll3_m3_ck>;
-		clock-mult = <2>;
-		clock-div = <1>;
-	};
-
-	dpll3_m3x2_ck: dpll3_m3x2_ck@d00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&dpll3_m3x2_mul_ck>;
-		ti,bit-shift = <0xc>;
-		reg = <0x0d00>;
-		ti,set-bit-to-disable;
-	};
-
-	emu_core_alwon_ck: emu_core_alwon_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll3_m3x2_ck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	sys_altclk: sys_altclk {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <0x0>;
-	};
-
-	mcbsp_clks: mcbsp_clks {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <0x0>;
-	};
-
-	dpll3_m2_ck: dpll3_m2_ck@d40 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&dpll3_ck>;
-		ti,bit-shift = <27>;
-		ti,max-div = <31>;
-		reg = <0x0d40>;
-		ti,index-starts-at-one;
-	};
-
-	core_ck: core_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll3_m2_ck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	dpll1_fck: dpll1_fck@940 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&core_ck>;
-		ti,bit-shift = <19>;
-		ti,max-div = <7>;
-		reg = <0x0940>;
-		ti,index-starts-at-one;
-	};
-
-	dpll1_ck: dpll1_ck@904 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-dpll-clock";
-		clocks = <&sys_ck>, <&dpll1_fck>;
-		reg = <0x0904>, <0x0924>, <0x0940>, <0x0934>;
-	};
-
-	dpll1_x2_ck: dpll1_x2_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll1_ck>;
-		clock-mult = <2>;
-		clock-div = <1>;
-	};
-
-	dpll1_x2m2_ck: dpll1_x2m2_ck@944 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&dpll1_x2_ck>;
-		ti,max-div = <31>;
-		reg = <0x0944>;
-		ti,index-starts-at-one;
-	};
-
-	cm_96m_fck: cm_96m_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&omap_96m_alwon_fck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	omap_96m_fck: omap_96m_fck@d40 {
-		#clock-cells = <0>;
-		compatible = "ti,mux-clock";
-		clocks = <&cm_96m_fck>, <&sys_ck>;
-		ti,bit-shift = <6>;
-		reg = <0x0d40>;
-	};
-
-	dpll4_m3_ck: dpll4_m3_ck@e40 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&dpll4_ck>;
-		ti,bit-shift = <8>;
-		ti,max-div = <32>;
-		reg = <0x0e40>;
-		ti,index-starts-at-one;
-	};
-
-	dpll4_m3x2_mul_ck: dpll4_m3x2_mul_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll4_m3_ck>;
-		clock-mult = <2>;
-		clock-div = <1>;
-	};
-
-	dpll4_m3x2_ck: dpll4_m3x2_ck@d00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&dpll4_m3x2_mul_ck>;
-		ti,bit-shift = <0x1c>;
-		reg = <0x0d00>;
-		ti,set-bit-to-disable;
-	};
-
-	omap_54m_fck: omap_54m_fck@d40 {
-		#clock-cells = <0>;
-		compatible = "ti,mux-clock";
-		clocks = <&dpll4_m3x2_ck>, <&sys_altclk>;
-		ti,bit-shift = <5>;
-		reg = <0x0d40>;
-	};
-
-	cm_96m_d2_fck: cm_96m_d2_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&cm_96m_fck>;
-		clock-mult = <1>;
-		clock-div = <2>;
-	};
-
-	omap_48m_fck: omap_48m_fck@d40 {
-		#clock-cells = <0>;
-		compatible = "ti,mux-clock";
-		clocks = <&cm_96m_d2_fck>, <&sys_altclk>;
-		ti,bit-shift = <3>;
-		reg = <0x0d40>;
-	};
-
-	omap_12m_fck: omap_12m_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&omap_48m_fck>;
-		clock-mult = <1>;
-		clock-div = <4>;
-	};
-
-	dpll4_m4_ck: dpll4_m4_ck@e40 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&dpll4_ck>;
-		ti,max-div = <16>;
-		reg = <0x0e40>;
-		ti,index-starts-at-one;
-	};
-
-	dpll4_m4x2_mul_ck: dpll4_m4x2_mul_ck {
-		#clock-cells = <0>;
-		compatible = "ti,fixed-factor-clock";
-		clocks = <&dpll4_m4_ck>;
-		ti,clock-mult = <2>;
-		ti,clock-div = <1>;
-		ti,set-rate-parent;
-	};
-
-	dpll4_m4x2_ck: dpll4_m4x2_ck@d00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&dpll4_m4x2_mul_ck>;
-		ti,bit-shift = <0x1d>;
-		reg = <0x0d00>;
-		ti,set-bit-to-disable;
-		ti,set-rate-parent;
-	};
-
-	dpll4_m5_ck: dpll4_m5_ck@f40 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&dpll4_ck>;
-		ti,max-div = <63>;
-		reg = <0x0f40>;
-		ti,index-starts-at-one;
-	};
-
-	dpll4_m5x2_mul_ck: dpll4_m5x2_mul_ck {
-		#clock-cells = <0>;
-		compatible = "ti,fixed-factor-clock";
-		clocks = <&dpll4_m5_ck>;
-		ti,clock-mult = <2>;
-		ti,clock-div = <1>;
-		ti,set-rate-parent;
-	};
-
-	dpll4_m5x2_ck: dpll4_m5x2_ck@d00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&dpll4_m5x2_mul_ck>;
-		ti,bit-shift = <0x1e>;
-		reg = <0x0d00>;
-		ti,set-bit-to-disable;
-		ti,set-rate-parent;
-	};
-
-	dpll4_m6_ck: dpll4_m6_ck@1140 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&dpll4_ck>;
-		ti,bit-shift = <24>;
-		ti,max-div = <63>;
-		reg = <0x1140>;
-		ti,index-starts-at-one;
-	};
-
-	dpll4_m6x2_mul_ck: dpll4_m6x2_mul_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll4_m6_ck>;
-		clock-mult = <2>;
-		clock-div = <1>;
-	};
-
-	dpll4_m6x2_ck: dpll4_m6x2_ck@d00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&dpll4_m6x2_mul_ck>;
-		ti,bit-shift = <0x1f>;
-		reg = <0x0d00>;
-		ti,set-bit-to-disable;
-	};
-
-	emu_per_alwon_ck: emu_per_alwon_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll4_m6x2_ck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	clkout2_src_gate_ck: clkout2_src_gate_ck@d70 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-no-wait-gate-clock";
-		clocks = <&core_ck>;
-		ti,bit-shift = <7>;
-		reg = <0x0d70>;
-	};
-
-	clkout2_src_mux_ck: clkout2_src_mux_ck@d70 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&core_ck>, <&sys_ck>, <&cm_96m_fck>, <&omap_54m_fck>;
-		reg = <0x0d70>;
-	};
-
-	clkout2_src_ck: clkout2_src_ck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&clkout2_src_gate_ck>, <&clkout2_src_mux_ck>;
-	};
-
-	sys_clkout2: sys_clkout2@d70 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&clkout2_src_ck>;
-		ti,bit-shift = <3>;
-		ti,max-div = <64>;
-		reg = <0x0d70>;
-		ti,index-power-of-two;
-	};
-
-	mpu_ck: mpu_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&dpll1_x2m2_ck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	arm_fck: arm_fck@924 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&mpu_ck>;
-		reg = <0x0924>;
-		ti,max-div = <2>;
-	};
-
-	emu_mpu_alwon_ck: emu_mpu_alwon_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&mpu_ck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	l3_ick: l3_ick@a40 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&core_ck>;
-		ti,max-div = <3>;
-		reg = <0x0a40>;
-		ti,index-starts-at-one;
-	};
-
-	l4_ick: l4_ick@a40 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&l3_ick>;
-		ti,bit-shift = <2>;
-		ti,max-div = <3>;
-		reg = <0x0a40>;
-		ti,index-starts-at-one;
-	};
-
-	rm_ick: rm_ick@c40 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&l4_ick>;
-		ti,bit-shift = <1>;
-		ti,max-div = <3>;
-		reg = <0x0c40>;
-		ti,index-starts-at-one;
-	};
-
-	gpt10_gate_fck: gpt10_gate_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <11>;
-		reg = <0x0a00>;
-	};
-
-	gpt10_mux_fck: gpt10_mux_fck@a40 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		ti,bit-shift = <6>;
-		reg = <0x0a40>;
-	};
-
-	gpt10_fck: gpt10_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&gpt10_gate_fck>, <&gpt10_mux_fck>;
-	};
-
-	gpt11_gate_fck: gpt11_gate_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <12>;
-		reg = <0x0a00>;
-	};
-
-	gpt11_mux_fck: gpt11_mux_fck@a40 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		ti,bit-shift = <7>;
-		reg = <0x0a40>;
-	};
-
-	gpt11_fck: gpt11_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&gpt11_gate_fck>, <&gpt11_mux_fck>;
-	};
-
-	core_96m_fck: core_96m_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&omap_96m_fck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	mmchs2_fck: mmchs2_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_96m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <25>;
-	};
-
-	mmchs1_fck: mmchs1_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_96m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <24>;
-	};
-
-	i2c3_fck: i2c3_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_96m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <17>;
-	};
-
-	i2c2_fck: i2c2_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_96m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <16>;
-	};
-
-	i2c1_fck: i2c1_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_96m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <15>;
-	};
-
-	mcbsp5_gate_fck: mcbsp5_gate_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&mcbsp_clks>;
-		ti,bit-shift = <10>;
-		reg = <0x0a00>;
-	};
-
-	mcbsp1_gate_fck: mcbsp1_gate_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&mcbsp_clks>;
-		ti,bit-shift = <9>;
-		reg = <0x0a00>;
-	};
-
-	core_48m_fck: core_48m_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&omap_48m_fck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	mcspi4_fck: mcspi4_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_48m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <21>;
-	};
-
-	mcspi3_fck: mcspi3_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_48m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <20>;
-	};
-
-	mcspi2_fck: mcspi2_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_48m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <19>;
-	};
-
-	mcspi1_fck: mcspi1_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_48m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <18>;
-	};
-
-	uart2_fck: uart2_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_48m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <14>;
-	};
-
-	uart1_fck: uart1_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_48m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <13>;
-	};
-
-	core_12m_fck: core_12m_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&omap_12m_fck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	hdq_fck: hdq_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_12m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <22>;
-	};
-
-	core_l3_ick: core_l3_ick {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&l3_ick>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	sdrc_ick: sdrc_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_l3_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <1>;
-	};
-
-	gpmc_fck: gpmc_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&core_l3_ick>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	core_l4_ick: core_l4_ick {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&l4_ick>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	mmchs2_ick: mmchs2_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <25>;
-	};
-
-	mmchs1_ick: mmchs1_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <24>;
-	};
-
-	hdq_ick: hdq_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <22>;
-	};
-
-	mcspi4_ick: mcspi4_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <21>;
-	};
-
-	mcspi3_ick: mcspi3_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <20>;
-	};
-
-	mcspi2_ick: mcspi2_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <19>;
-	};
-
-	mcspi1_ick: mcspi1_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <18>;
-	};
-
-	i2c3_ick: i2c3_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <17>;
-	};
-
-	i2c2_ick: i2c2_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <16>;
-	};
-
-	i2c1_ick: i2c1_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <15>;
-	};
-
-	uart2_ick: uart2_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <14>;
-	};
-
-	uart1_ick: uart1_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <13>;
-	};
-
-	gpt11_ick: gpt11_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <12>;
-	};
-
-	gpt10_ick: gpt10_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <11>;
-	};
-
-	mcbsp5_ick: mcbsp5_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <10>;
-	};
-
-	mcbsp1_ick: mcbsp1_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <9>;
-	};
-
-	omapctrl_ick: omapctrl_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <6>;
-	};
-
-	dss_tv_fck: dss_tv_fck@e00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&omap_54m_fck>;
-		reg = <0x0e00>;
-		ti,bit-shift = <2>;
-	};
-
-	dss_96m_fck: dss_96m_fck@e00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&omap_96m_fck>;
-		reg = <0x0e00>;
-		ti,bit-shift = <2>;
-	};
-
-	dss2_alwon_fck: dss2_alwon_fck@e00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&sys_ck>;
-		reg = <0x0e00>;
-		ti,bit-shift = <1>;
-	};
-
-	dummy_ck: dummy_ck {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <0>;
-	};
-
-	gpt1_gate_fck: gpt1_gate_fck@c00 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <0>;
-		reg = <0x0c00>;
-	};
-
-	gpt1_mux_fck: gpt1_mux_fck@c40 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		reg = <0x0c40>;
-	};
-
-	gpt1_fck: gpt1_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&gpt1_gate_fck>, <&gpt1_mux_fck>;
-	};
-
-	aes2_ick: aes2_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		ti,bit-shift = <28>;
-		reg = <0x0a10>;
-	};
-
-	wkup_32k_fck: wkup_32k_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&omap_32k_fck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	gpio1_dbck: gpio1_dbck@c00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&wkup_32k_fck>;
-		reg = <0x0c00>;
-		ti,bit-shift = <3>;
-	};
-
-	sha12_ick: sha12_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <27>;
-	};
-
-	wdt2_fck: wdt2_fck@c00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&wkup_32k_fck>;
-		reg = <0x0c00>;
-		ti,bit-shift = <5>;
-	};
-
-	wdt2_ick: wdt2_ick@c10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&wkup_l4_ick>;
-		reg = <0x0c10>;
-		ti,bit-shift = <5>;
-	};
-
-	wdt1_ick: wdt1_ick@c10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&wkup_l4_ick>;
-		reg = <0x0c10>;
-		ti,bit-shift = <4>;
-	};
-
-	gpio1_ick: gpio1_ick@c10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&wkup_l4_ick>;
-		reg = <0x0c10>;
-		ti,bit-shift = <3>;
-	};
-
-	omap_32ksync_ick: omap_32ksync_ick@c10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&wkup_l4_ick>;
-		reg = <0x0c10>;
-		ti,bit-shift = <2>;
-	};
-
-	gpt12_ick: gpt12_ick@c10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&wkup_l4_ick>;
-		reg = <0x0c10>;
-		ti,bit-shift = <1>;
-	};
-
-	gpt1_ick: gpt1_ick@c10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&wkup_l4_ick>;
-		reg = <0x0c10>;
-		ti,bit-shift = <0>;
-	};
-
-	per_96m_fck: per_96m_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&omap_96m_alwon_fck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	per_48m_fck: per_48m_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&omap_48m_fck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	uart3_fck: uart3_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&per_48m_fck>;
-		reg = <0x1000>;
-		ti,bit-shift = <11>;
-	};
-
-	gpt2_gate_fck: gpt2_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <3>;
-		reg = <0x1000>;
-	};
-
-	gpt2_mux_fck: gpt2_mux_fck@1040 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		reg = <0x1040>;
-	};
-
-	gpt2_fck: gpt2_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&gpt2_gate_fck>, <&gpt2_mux_fck>;
-	};
-
-	gpt3_gate_fck: gpt3_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <4>;
-		reg = <0x1000>;
-	};
-
-	gpt3_mux_fck: gpt3_mux_fck@1040 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		ti,bit-shift = <1>;
-		reg = <0x1040>;
-	};
-
-	gpt3_fck: gpt3_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&gpt3_gate_fck>, <&gpt3_mux_fck>;
-	};
-
-	gpt4_gate_fck: gpt4_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <5>;
-		reg = <0x1000>;
-	};
-
-	gpt4_mux_fck: gpt4_mux_fck@1040 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		ti,bit-shift = <2>;
-		reg = <0x1040>;
-	};
-
-	gpt4_fck: gpt4_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&gpt4_gate_fck>, <&gpt4_mux_fck>;
-	};
-
-	gpt5_gate_fck: gpt5_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <6>;
-		reg = <0x1000>;
-	};
-
-	gpt5_mux_fck: gpt5_mux_fck@1040 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		ti,bit-shift = <3>;
-		reg = <0x1040>;
-	};
-
-	gpt5_fck: gpt5_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&gpt5_gate_fck>, <&gpt5_mux_fck>;
-	};
-
-	gpt6_gate_fck: gpt6_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <7>;
-		reg = <0x1000>;
-	};
-
-	gpt6_mux_fck: gpt6_mux_fck@1040 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		ti,bit-shift = <4>;
-		reg = <0x1040>;
-	};
-
-	gpt6_fck: gpt6_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&gpt6_gate_fck>, <&gpt6_mux_fck>;
-	};
-
-	gpt7_gate_fck: gpt7_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <8>;
-		reg = <0x1000>;
-	};
-
-	gpt7_mux_fck: gpt7_mux_fck@1040 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		ti,bit-shift = <5>;
-		reg = <0x1040>;
-	};
-
-	gpt7_fck: gpt7_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&gpt7_gate_fck>, <&gpt7_mux_fck>;
-	};
-
-	gpt8_gate_fck: gpt8_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <9>;
-		reg = <0x1000>;
-	};
-
-	gpt8_mux_fck: gpt8_mux_fck@1040 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		ti,bit-shift = <6>;
-		reg = <0x1040>;
-	};
-
-	gpt8_fck: gpt8_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&gpt8_gate_fck>, <&gpt8_mux_fck>;
-	};
-
-	gpt9_gate_fck: gpt9_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <10>;
-		reg = <0x1000>;
-	};
-
-	gpt9_mux_fck: gpt9_mux_fck@1040 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		ti,bit-shift = <7>;
-		reg = <0x1040>;
-	};
-
-	gpt9_fck: gpt9_fck {
-		#clock-cells = <0>;
-		compatible = "ti,composite-clock";
-		clocks = <&gpt9_gate_fck>, <&gpt9_mux_fck>;
-	};
-
-	per_32k_alwon_fck: per_32k_alwon_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&omap_32k_fck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	gpio6_dbck: gpio6_dbck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&per_32k_alwon_fck>;
-		reg = <0x1000>;
-		ti,bit-shift = <17>;
-	};
-
-	gpio5_dbck: gpio5_dbck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&per_32k_alwon_fck>;
-		reg = <0x1000>;
-		ti,bit-shift = <16>;
-	};
-
-	gpio4_dbck: gpio4_dbck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&per_32k_alwon_fck>;
-		reg = <0x1000>;
-		ti,bit-shift = <15>;
-	};
-
-	gpio3_dbck: gpio3_dbck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&per_32k_alwon_fck>;
-		reg = <0x1000>;
-		ti,bit-shift = <14>;
-	};
-
-	gpio2_dbck: gpio2_dbck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&per_32k_alwon_fck>;
-		reg = <0x1000>;
-		ti,bit-shift = <13>;
-	};
-
-	wdt3_fck: wdt3_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&per_32k_alwon_fck>;
-		reg = <0x1000>;
-		ti,bit-shift = <12>;
-	};
-
-	per_l4_ick: per_l4_ick {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&l4_ick>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	gpio6_ick: gpio6_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <17>;
-	};
-
-	gpio5_ick: gpio5_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <16>;
-	};
-
-	gpio4_ick: gpio4_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <15>;
-	};
-
-	gpio3_ick: gpio3_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <14>;
-	};
-
-	gpio2_ick: gpio2_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <13>;
-	};
-
-	wdt3_ick: wdt3_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <12>;
-	};
-
-	uart3_ick: uart3_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <11>;
-	};
-
-	uart4_ick: uart4_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <18>;
-	};
-
-	gpt9_ick: gpt9_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <10>;
-	};
-
-	gpt8_ick: gpt8_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <9>;
-	};
-
-	gpt7_ick: gpt7_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <8>;
-	};
-
-	gpt6_ick: gpt6_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <7>;
-	};
-
-	gpt5_ick: gpt5_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <6>;
-	};
-
-	gpt4_ick: gpt4_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <5>;
-	};
-
-	gpt3_ick: gpt3_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <4>;
-	};
-
-	gpt2_ick: gpt2_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <3>;
-	};
-
-	mcbsp2_ick: mcbsp2_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <0>;
-	};
-
-	mcbsp3_ick: mcbsp3_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <1>;
-	};
-
-	mcbsp4_ick: mcbsp4_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <2>;
-	};
-
-	mcbsp2_gate_fck: mcbsp2_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&mcbsp_clks>;
-		ti,bit-shift = <0>;
-		reg = <0x1000>;
-	};
-
-	mcbsp3_gate_fck: mcbsp3_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&mcbsp_clks>;
-		ti,bit-shift = <1>;
-		reg = <0x1000>;
-	};
-
-	mcbsp4_gate_fck: mcbsp4_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&mcbsp_clks>;
-		ti,bit-shift = <2>;
-		reg = <0x1000>;
-	};
-
-	emu_src_mux_ck: emu_src_mux_ck@1140 {
-		#clock-cells = <0>;
-		compatible = "ti,mux-clock";
-		clocks = <&sys_ck>, <&emu_core_alwon_ck>, <&emu_per_alwon_ck>, <&emu_mpu_alwon_ck>;
-		reg = <0x1140>;
-	};
-
-	emu_src_ck: emu_src_ck {
-		#clock-cells = <0>;
-		compatible = "ti,clkdm-gate-clock";
-		clocks = <&emu_src_mux_ck>;
-	};
-
-	pclk_fck: pclk_fck@1140 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&emu_src_ck>;
-		ti,bit-shift = <8>;
-		ti,max-div = <7>;
-		reg = <0x1140>;
-		ti,index-starts-at-one;
-	};
-
-	pclkx2_fck: pclkx2_fck@1140 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&emu_src_ck>;
-		ti,bit-shift = <6>;
-		ti,max-div = <3>;
-		reg = <0x1140>;
-		ti,index-starts-at-one;
-	};
-
-	atclk_fck: atclk_fck@1140 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&emu_src_ck>;
-		ti,bit-shift = <4>;
-		ti,max-div = <3>;
-		reg = <0x1140>;
-		ti,index-starts-at-one;
-	};
-
-	traceclk_src_fck: traceclk_src_fck@1140 {
-		#clock-cells = <0>;
-		compatible = "ti,mux-clock";
-		clocks = <&sys_ck>, <&emu_core_alwon_ck>, <&emu_per_alwon_ck>, <&emu_mpu_alwon_ck>;
-		ti,bit-shift = <2>;
-		reg = <0x1140>;
-	};
-
-	traceclk_fck: traceclk_fck@1140 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&traceclk_src_fck>;
-		ti,bit-shift = <11>;
-		ti,max-div = <7>;
-		reg = <0x1140>;
-		ti,index-starts-at-one;
-	};
-
-	secure_32k_fck: secure_32k_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <32768>;
-	};
-
-	gpt12_fck: gpt12_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&secure_32k_fck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-
-	wdt1_fck: wdt1_fck {
-		#clock-cells = <0>;
-		compatible = "fixed-factor-clock";
-		clocks = <&secure_32k_fck>;
-		clock-mult = <1>;
-		clock-div = <1>;
-	};
-};
-
-&cm_clockdomains {
-	core_l3_clkdm: core_l3_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&sdrc_ick>;
-	};
-
-	dpll3_clkdm: dpll3_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&dpll3_ck>;
-	};
-
-	dpll1_clkdm: dpll1_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&dpll1_ck>;
-	};
-
-	per_clkdm: per_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&uart3_fck>, <&gpio6_dbck>, <&gpio5_dbck>,
-			 <&gpio4_dbck>, <&gpio3_dbck>, <&gpio2_dbck>,
-			 <&wdt3_fck>, <&gpio6_ick>, <&gpio5_ick>, <&gpio4_ick>,
-			 <&gpio3_ick>, <&gpio2_ick>, <&wdt3_ick>, <&uart3_ick>,
-			 <&uart4_ick>, <&gpt9_ick>, <&gpt8_ick>, <&gpt7_ick>,
-			 <&gpt6_ick>, <&gpt5_ick>, <&gpt4_ick>, <&gpt3_ick>,
-			 <&gpt2_ick>, <&mcbsp2_ick>, <&mcbsp3_ick>,
-			 <&mcbsp4_ick>;
-	};
-
-	emu_clkdm: emu_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&emu_src_ck>;
-	};
-
-	dpll4_clkdm: dpll4_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&dpll4_ck>;
-	};
-
-	wkup_clkdm: wkup_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&gpio1_dbck>, <&wdt2_fck>, <&wdt2_ick>, <&wdt1_ick>,
-			 <&gpio1_ick>, <&omap_32ksync_ick>, <&gpt12_ick>,
-			 <&gpt1_ick>;
-	};
-
-	dss_clkdm: dss_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&dss_tv_fck>, <&dss_96m_fck>, <&dss2_alwon_fck>;
-	};
-
-	core_l4_clkdm: core_l4_clkdm {
-		compatible = "ti,clockdomain";
-		clocks = <&mmchs2_fck>, <&mmchs1_fck>, <&i2c3_fck>, <&i2c2_fck>,
-			 <&i2c1_fck>, <&mcspi4_fck>, <&mcspi3_fck>,
-			 <&mcspi2_fck>, <&mcspi1_fck>, <&uart2_fck>,
-			 <&uart1_fck>, <&hdq_fck>, <&mmchs2_ick>, <&mmchs1_ick>,
-			 <&hdq_ick>, <&mcspi4_ick>, <&mcspi3_ick>,
-			 <&mcspi2_ick>, <&mcspi1_ick>, <&i2c3_ick>, <&i2c2_ick>,
-			 <&i2c1_ick>, <&uart2_ick>, <&uart1_ick>, <&gpt11_ick>,
-			 <&gpt10_ick>, <&mcbsp5_ick>, <&mcbsp1_ick>,
-			 <&omapctrl_ick>, <&aes2_ick>, <&sha12_ick>;
-	};
-};
diff --git a/arch/arm/boot/dts/omap4-cpu-thermal.dtsi b/arch/arm/boot/dts/omap4-cpu-thermal.dtsi
deleted file mode 100644
index 03d054b2bf9a..000000000000
--- a/arch/arm/boot/dts/omap4-cpu-thermal.dtsi
+++ /dev/null
@@ -1,41 +0,0 @@
-/*
- * Device Tree Source for OMAP4/5 SoC CPU thermal
- *
- * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
- * Contact: Eduardo Valentin <eduardo.valentin@ti.com>
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
-
-#include <dt-bindings/thermal/thermal.h>
-
-cpu_thermal: cpu_thermal {
-	polling-delay-passive = <250>; /* milliseconds */
-	polling-delay = <1000>; /* milliseconds */
-
-			/* sensor       ID */
-        thermal-sensors = <&bandgap     0>;
-
-	cpu_trips: trips {
-                cpu_alert0: cpu_alert {
-                        temperature = <100000>; /* millicelsius */
-                        hysteresis = <2000>; /* millicelsius */
-                        type = "passive";
-                };
-                cpu_crit: cpu_crit {
-                        temperature = <125000>; /* millicelsius */
-                        hysteresis = <2000>; /* millicelsius */
-                        type = "critical";
-                };
-        };
-
-	cpu_cooling_maps: cooling-maps {
-		map0 {
-			trip = <&cpu_alert0>;
-			cooling-device =
-				<&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/ox810se-wd-mbwe.dts b/arch/arm/boot/dts/ox810se-wd-mbwe.dts
deleted file mode 100644
index c59e06ff2423..000000000000
--- a/arch/arm/boot/dts/ox810se-wd-mbwe.dts
+++ /dev/null
@@ -1,115 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * wd-mbwe.dtsi - Device tree file for Western Digital My Book World Edition
- *
- * Copyright (C) 2016 Neil Armstrong <narmstrong@baylibre.com>
- */
-
-/dts-v1/;
-#include "ox810se.dtsi"
-
-/ {
-	model = "Western Digital My Book World Edition";
-
-	compatible = "wd,mbwe", "oxsemi,ox810se";
-
-	chosen {
-		bootargs = "console=ttyS1,115200n8 earlyprintk=serial";
-	};
-
-	memory {
-		/* 128Mbytes DDR */
-		reg = <0x48000000 0x8000000>;
-	};
-
-	aliases {
-		serial1 = &uart1;
-		gpio0 = &gpio0;
-		gpio1 = &gpio1;
-	};
-
-	gpio-keys-polled {
-		compatible = "gpio-keys-polled";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		poll-interval = <100>;
-
-		power {
-			label = "power";
-			gpios = <&gpio0 0 1>;
-			linux,code = <0x198>;
-		};
-
-		recovery {
-			label = "recovery";
-			gpios = <&gpio0 4 1>;
-			linux,code = <0xab>;
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		a0 {
-			label = "activity0";
-			gpios = <&gpio0 25 0>;
-			default-state = "keep";
-		};
-
-		a1 {
-			label = "activity1";
-			gpios = <&gpio0 26 0>;
-			default-state = "keep";
-		};
-
-		a2 {
-			label = "activity2";
-			gpios = <&gpio0 5 0>;
-			default-state = "keep";
-		};
-
-		a3 {
-			label = "activity3";
-			gpios = <&gpio0 6 0>;
-			default-state = "keep";
-		};
-
-		a4 {
-			label = "activity4";
-			gpios = <&gpio0 7 0>;
-			default-state = "keep";
-		};
-
-		a5 {
-			label = "activity5";
-			gpios = <&gpio1 2 0>;
-			default-state = "keep";
-		};
-	};
-
-	i2c-gpio {
-		compatible = "i2c-gpio";
-		gpios = <&gpio0 3 0 /* sda */
-			 &gpio0 2 0 /* scl */
-			 >;
-		i2c-gpio,delay-us = <2>;        /* ~100 kHz */
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		rtc0: rtc@48 {
-			compatible = "st,m41t00";
-			reg = <0x68>;
-		};
-	};
-};
-
-&etha {
-	status = "okay";
-};
-
-&uart1 {
-	status = "okay";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
-};
diff --git a/arch/arm/boot/dts/ox810se.dtsi b/arch/arm/boot/dts/ox810se.dtsi
deleted file mode 100644
index 96c0745f7b70..000000000000
--- a/arch/arm/boot/dts/ox810se.dtsi
+++ /dev/null
@@ -1,357 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * ox810se.dtsi - Device tree file for Oxford Semiconductor OX810SE SoC
- *
- * Copyright (C) 2016 Neil Armstrong <narmstrong@baylibre.com>
- */
-
-#include <dt-bindings/clock/oxsemi,ox810se.h>
-#include <dt-bindings/reset/oxsemi,ox810se.h>
-
-/ {
-	#address-cells = <1>;
-	#size-cells = <1>;
-	compatible = "oxsemi,ox810se";
-
-	cpus {
-		#address-cells = <0>;
-		#size-cells = <0>;
-
-		cpu {
-			device_type = "cpu";
-			compatible = "arm,arm926ej-s";
-			clocks = <&armclk>;
-		};
-	};
-
-	memory {
-		device_type = "memory";
-		/* Max 256MB @ 0x48000000 */
-		reg = <0x48000000 0x10000000>;
-	};
-
-	clocks {
-		osc: oscillator {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <25000000>;
-		};
-
-		gmacclk: gmacclk {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <125000000>;
-		};
-
-		rpsclk: rpsclk {
-			compatible = "fixed-factor-clock";
-			#clock-cells = <0>;
-			clock-div = <1>;
-			clock-mult = <1>;
-			clocks = <&osc>;
-		};
-
-		pll400: pll400 {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <733333333>;
-		};
-
-		sysclk: sysclk {
-			compatible = "fixed-factor-clock";
-			#clock-cells = <0>;
-			clock-div = <4>;
-			clock-mult = <1>;
-			clocks = <&pll400>;
-		};
-
-		armclk: armclk {
-			compatible = "fixed-factor-clock";
-			#clock-cells = <0>;
-			clock-div = <2>;
-			clock-mult = <1>;
-			clocks = <&pll400>;
-		};
-	};
-
-	soc {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "simple-bus";
-		ranges;
-		interrupt-parent = <&intc>;
-
-		etha: ethernet@40400000 {
-			compatible = "oxsemi,ox810se-dwmac", "snps,dwmac";
-			reg = <0x40400000 0x2000>;
-			interrupts = <8>;
-			interrupt-names = "macirq";
-			mac-address = [000000000000]; /* Filled in by U-Boot */
-			phy-mode = "rgmii";
-
-			clocks = <&stdclk 6>, <&gmacclk>;
-			clock-names = "gmac", "stmmaceth";
-			resets = <&reset 6>;
-
-			/* Regmap for sys registers */
-			oxsemi,sys-ctrl = <&sys>;
-
-			status = "disabled";
-		};
-
-		apb-bridge@44000000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "simple-bus";
-			ranges = <0 0x44000000 0x1000000>;
-
-			pinctrl: pinctrl {
-				compatible = "oxsemi,ox810se-pinctrl";
-
-				/* Regmap for sys registers */
-				oxsemi,sys-ctrl = <&sys>;
-
-				pinctrl_uart0: uart0 {
-					uart0a {
-						pins = "gpio31";
-						function = "fct3";
-					};
-					uart0b {
-						pins = "gpio32";
-						function = "fct3";
-					};
-				};
-
-				pinctrl_uart0_modem: uart0_modem {
-					uart0c {
-						pins = "gpio27";
-						function = "fct3";
-					};
-					uart0d {
-						pins = "gpio28";
-						function = "fct3";
-					};
-					uart0e {
-						pins = "gpio29";
-						function = "fct3";
-					};
-					uart0f {
-						pins = "gpio30";
-						function = "fct3";
-					};
-					uart0g {
-						pins = "gpio33";
-						function = "fct3";
-					};
-					uart0h {
-						pins = "gpio34";
-						function = "fct3";
-					};
-				};
-
-				pinctrl_uart1: uart1 {
-					uart1a {
-						pins = "gpio20";
-						function = "fct3";
-					};
-					uart1b {
-						pins = "gpio22";
-						function = "fct3";
-					};
-				};
-
-				pinctrl_uart1_modem: uart1_modem {
-					uart1c {
-						pins = "gpio8";
-						function = "fct3";
-					};
-					uart1d {
-						pins = "gpio9";
-						function = "fct3";
-					};
-					uart1e {
-						pins = "gpio23";
-						function = "fct3";
-					};
-					uart1f {
-						pins = "gpio24";
-						function = "fct3";
-					};
-					uart1g {
-						pins = "gpio25";
-						function = "fct3";
-					};
-					uart1h {
-						pins = "gpio26";
-						function = "fct3";
-					};
-				};
-
-				pinctrl_uart2: uart2 {
-					uart2a {
-						pins = "gpio6";
-						function = "fct3";
-					};
-					uart2b {
-						pins = "gpio7";
-						function = "fct3";
-					};
-				};
-
-				pinctrl_uart2_modem: uart2_modem {
-					uart2c {
-						pins = "gpio0";
-						function = "fct3";
-					};
-					uart2d {
-						pins = "gpio1";
-						function = "fct3";
-					};
-					uart2e {
-						pins = "gpio2";
-						function = "fct3";
-					};
-					uart2f {
-						pins = "gpio3";
-						function = "fct3";
-					};
-					uart2g {
-						pins = "gpio4";
-						function = "fct3";
-					};
-					uart2h {
-						pins = "gpio5";
-						function = "fct3";
-					};
-				};
-			};
-
-			gpio0: gpio@0 {
-				compatible = "oxsemi,ox810se-gpio";
-				reg = <0x000000 0x100000>;
-				interrupts = <21>;
-				#gpio-cells = <2>;
-				gpio-controller;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				ngpios = <32>;
-				oxsemi,gpio-bank = <0>;
-				gpio-ranges = <&pinctrl 0 0 32>;
-			};
-
-			gpio1: gpio@100000 {
-				compatible = "oxsemi,ox810se-gpio";
-				reg = <0x100000 0x100000>;
-				interrupts = <22>;
-				#gpio-cells = <2>;
-				gpio-controller;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				ngpios = <3>;
-				oxsemi,gpio-bank = <1>;
-				gpio-ranges = <&pinctrl 0 32 3>;
-			};
-
-			uart0: serial@200000 {
-			       compatible = "ns16550a";
-			       reg = <0x200000 0x100000>;
-			       clocks = <&sysclk>;
-			       interrupts = <23>;
-			       reg-shift = <0>;
-			       fifo-size = <16>;
-			       reg-io-width = <1>;
-			       current-speed = <115200>;
-			       no-loopback-test;
-			       status = "disabled";
-			       resets = <&reset RESET_UART1>;
-			};
-
-			uart1: serial@300000 {
-			       compatible = "ns16550a";
-			       reg = <0x300000 0x100000>;
-			       clocks = <&sysclk>;
-			       interrupts = <24>;
-			       reg-shift = <0>;
-			       fifo-size = <16>;
-			       reg-io-width = <1>;
-			       current-speed = <115200>;
-			       no-loopback-test;
-			       status = "disabled";
-			       resets = <&reset RESET_UART2>;
-			};
-
-			uart2: serial@900000 {
-			       compatible = "ns16550a";
-			       reg = <0x900000 0x100000>;
-			       clocks = <&sysclk>;
-			       interrupts = <29>;
-			       reg-shift = <0>;
-			       fifo-size = <16>;
-			       reg-io-width = <1>;
-			       current-speed = <115200>;
-			       no-loopback-test;
-			       status = "disabled";
-			       resets = <&reset RESET_UART3>;
-			};
-
-			uart3: serial@a00000 {
-			       compatible = "ns16550a";
-			       reg = <0xa00000 0x100000>;
-			       clocks = <&sysclk>;
-			       interrupts = <30>;
-			       reg-shift = <0>;
-			       fifo-size = <16>;
-			       reg-io-width = <1>;
-			       current-speed = <115200>;
-			       no-loopback-test;
-			       status = "disabled";
-			       resets = <&reset RESET_UART4>;
-			};
-		};
-
-		apb-bridge@45000000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "simple-bus";
-			ranges = <0 0x45000000 0x1000000>;
-
-			sys: sys-ctrl@0 {
-				compatible = "oxsemi,ox810se-sys-ctrl", "syscon", "simple-mfd";
-				reg = <0x000000 0x100000>;
-
-				reset: reset-controller {
-					compatible = "oxsemi,ox810se-reset";
-					#reset-cells = <1>;
-				};
-
-				stdclk: stdclk {
-					compatible = "oxsemi,ox810se-stdclk";
-					#clock-cells = <1>;
-				};
-			};
-
-			rps@300000 {
-				#address-cells = <1>;
-				#size-cells = <1>;
-				compatible = "simple-bus";
-				ranges = <0 0x300000 0x100000>;
-
-				intc: interrupt-controller@0 {
-					compatible = "oxsemi,ox810se-rps-irq";
-					interrupt-controller;
-					reg = <0 0x200>;
-					#interrupt-cells = <1>;
-					valid-mask = <0xffffffff>;
-					clear-mask = <0xffffffff>;
-				};
-
-				timer0: timer@200 {
-					compatible = "oxsemi,ox810se-rps-timer";
-					reg = <0x200 0x40>;
-					clocks = <&rpsclk>;
-					interrupts = <4 5>;
-				};
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/ox820-cloudengines-pogoplug-series-3.dts b/arch/arm/boot/dts/ox820-cloudengines-pogoplug-series-3.dts
deleted file mode 100644
index c3daceccde55..000000000000
--- a/arch/arm/boot/dts/ox820-cloudengines-pogoplug-series-3.dts
+++ /dev/null
@@ -1,93 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * cloudengines-pogoplug-series-3.dtsi - Device tree file for Cloud Engines PogoPlug Series 3
- *
- * Copyright (C) 2016 Neil Armstrong <narmstrong@baylibre.com>
- */
-
-/dts-v1/;
-#include "ox820.dtsi"
-
-/ {
-	model = "Cloud Engines PogoPlug Series 3";
-
-	compatible = "cloudengines,pogoplugv3", "oxsemi,ox820";
-
-	chosen {
-		bootargs = "earlyprintk";
-		stdout-path = "serial0:115200n8";
-	};
-
-	memory {
-		/* 128Mbytes DDR */
-		reg = <0x60000000 0x8000000>;
-	};
-
-	aliases {
-		serial0 = &uart0;
-		gpio0 = &gpio0;
-		gpio1 = &gpio1;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		blue {
-			label = "pogoplug:blue";
-			gpios = <&gpio0 2 0>;
-			default-state = "keep";
-		};
-
-		orange {
-			label = "pogoplug:orange";
-			gpios = <&gpio1 16 1>;
-			default-state = "keep";
-		};
-
-		green {
-			label = "pogoplug:green";
-			gpios = <&gpio1 17 1>;
-			default-state = "keep";
-		};
-	};
-};
-
-&uart0 {
-	status = "okay";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart0>;
-};
-
-&nandc {
-	status = "okay";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_nand>;
-
-	nand@0 {
-		reg = <0>;
-		#address-cells = <1>;
-		#size-cells = <1>;
-		nand-ecc-mode = "soft";
-		nand-ecc-algo = "hamming";
-
-		partition@0 {
-			label = "boot";
-			reg = <0x00000000 0x00e00000>;
-			read-only;
-		};
-
-		partition@e00000 {
-			label = "ubi";
-			reg = <0x00e00000 0x07200000>;
-		};
-	};
-};
-
-&etha {
-	status = "okay";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_etha_mdio>;
-};
diff --git a/arch/arm/boot/dts/ox820.dtsi b/arch/arm/boot/dts/ox820.dtsi
deleted file mode 100644
index 90846a7655b4..000000000000
--- a/arch/arm/boot/dts/ox820.dtsi
+++ /dev/null
@@ -1,299 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * ox820.dtsi - Device tree file for Oxford Semiconductor OX820 SoC
- *
- * Copyright (C) 2016 Neil Armstrong <narmstrong@baylibre.com>
- */
-
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/clock/oxsemi,ox820.h>
-#include <dt-bindings/reset/oxsemi,ox820.h>
-
-/ {
-	#address-cells = <1>;
-	#size-cells = <1>;
-	compatible = "oxsemi,ox820";
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		enable-method = "oxsemi,ox820-smp";
-
-		cpu@0 {
-			device_type = "cpu";
-			compatible = "arm,arm11mpcore";
-			clocks = <&armclk>;
-			reg = <0>;
-		};
-
-		cpu@1 {
-			device_type = "cpu";
-			compatible = "arm,arm11mpcore";
-			clocks = <&armclk>;
-			reg = <1>;
-		};
-	};
-
-	memory {
-		device_type = "memory";
-		/* Max 512MB @ 0x60000000 */
-		reg = <0x60000000 0x20000000>;
-	};
-
-	clocks {
-		osc: oscillator {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <25000000>;
-		};
-
-		gmacclk: gmacclk {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <125000000>;
-		};
-
-		sysclk: sysclk {
-			compatible = "fixed-factor-clock";
-			#clock-cells = <0>;
-			clock-div = <4>;
-			clock-mult = <1>;
-			clocks = <&osc>;
-		};
-
-		plla: plla {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <850000000>;
-		};
-
-		armclk: armclk {
-			compatible = "fixed-factor-clock";
-			#clock-cells = <0>;
-			clock-div = <2>;
-			clock-mult = <1>;
-			clocks = <&plla>;
-		};
-	};
-
-	soc {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "simple-bus";
-		ranges;
-		interrupt-parent = <&gic>;
-
-		nandc: nand-controller@41000000 {
-			compatible = "oxsemi,ox820-nand";
-			reg = <0x41000000 0x100000>;
-			clocks = <&stdclk CLK_820_NAND>;
-			resets = <&reset RESET_NAND>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			status = "disabled";
-		};
-
-		etha: ethernet@40400000 {
-			compatible = "oxsemi,ox820-dwmac", "snps,dwmac";
-			reg = <0x40400000 0x2000>;
-			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "macirq", "eth_wake_irq";
-			mac-address = [000000000000]; /* Filled in by U-Boot */
-			phy-mode = "rgmii";
-
-			clocks = <&stdclk CLK_820_ETHA>, <&gmacclk>;
-			clock-names = "gmac", "stmmaceth";
-			resets = <&reset RESET_MAC>;
-
-			/* Regmap for sys registers */
-			oxsemi,sys-ctrl = <&sys>;
-
-			status = "disabled";
-		};
-
-		apb-bridge@44000000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "simple-bus";
-			ranges = <0 0x44000000 0x1000000>;
-
-			pinctrl: pinctrl {
-				compatible = "oxsemi,ox820-pinctrl";
-
-				/* Regmap for sys registers */
-				oxsemi,sys-ctrl = <&sys>;
-
-				pinctrl_uart0: uart0 {
-					uart0 {
-						pins = "gpio30", "gpio31";
-						function = "fct5";
-					};
-				};
-
-				pinctrl_uart0_modem: uart0_modem {
-					uart0_modem_a {
-						pins = "gpio24", "gpio24", "gpio26", "gpio27";
-						function = "fct4";
-					};
-					uart0_modem_b {
-						pins = "gpio28", "gpio29";
-						function = "fct5";
-					};
-				};
-
-				pinctrl_uart1: uart1 {
-					uart1 {
-						pins = "gpio7", "gpio8";
-						function = "fct4";
-					};
-				};
-
-				pinctrl_uart1_modem: uart1_modem {
-					uart1_modem {
-						pins = "gpio5", "gpio6", "gpio40", "gpio41", "gpio42", "gpio43";
-						function = "fct4";
-					};
-				};
-
-				pinctrl_etha_mdio: etha_mdio {
-					etha_mdio {
-						pins = "gpio3", "gpio4";
-						function = "fct1";
-					};
-				};
-
-				pinctrl_nand: nand {
-					nand {
-						pins = "gpio12", "gpio13", "gpio14", "gpio15",
-						     "gpio16", "gpio17", "gpio18", "gpio19",
-						     "gpio20", "gpio21", "gpio22", "gpio23",
-						     "gpio24";
-						function = "fct1";
-					};
-				};
-			};
-
-			gpio0: gpio@0 {
-				compatible = "oxsemi,ox820-gpio";
-				reg = <0x000000 0x100000>;
-				interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
-				#gpio-cells = <2>;
-				gpio-controller;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				ngpios = <32>;
-				oxsemi,gpio-bank = <0>;
-				gpio-ranges = <&pinctrl 0 0 32>;
-			};
-
-			gpio1: gpio@100000 {
-				compatible = "oxsemi,ox820-gpio";
-				reg = <0x100000 0x100000>;
-				interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
-				#gpio-cells = <2>;
-				gpio-controller;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				ngpios = <18>;
-				oxsemi,gpio-bank = <1>;
-				gpio-ranges = <&pinctrl 0 32 18>;
-			};
-
-			uart0: serial@200000 {
-			       compatible = "ns16550a";
-			       reg = <0x200000 0x100000>;
-			       interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
-			       reg-shift = <0>;
-			       fifo-size = <16>;
-			       reg-io-width = <1>;
-			       current-speed = <115200>;
-			       no-loopback-test;
-			       status = "disabled";
-			       clocks = <&sysclk>;
-			       resets = <&reset RESET_UART1>;
-			};
-
-			uart1: serial@300000 {
-			       compatible = "ns16550a";
-			       reg = <0x200000 0x100000>;
-			       interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
-			       reg-shift = <0>;
-			       fifo-size = <16>;
-			       reg-io-width = <1>;
-			       current-speed = <115200>;
-			       no-loopback-test;
-			       status = "disabled";
-			       clocks = <&sysclk>;
-			       resets = <&reset RESET_UART2>;
-			};
-
-			rps@400000 {
-				#address-cells = <1>;
-				#size-cells = <1>;
-				compatible = "simple-bus";
-				ranges = <0 0x400000 0x100000>;
-
-				intc: interrupt-controller@0 {
-					compatible = "oxsemi,ox820-rps-irq", "oxsemi,ox810se-rps-irq";
-					interrupt-controller;
-					reg = <0 0x200>;
-					interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
-					#interrupt-cells = <1>;
-					valid-mask = <0xffffffff>;
-					clear-mask = <0xffffffff>;
-				};
-
-				timer0: timer@200 {
-					compatible = "oxsemi,ox820-rps-timer";
-					reg = <0x200 0x40>;
-					clocks = <&sysclk>;
-					interrupt-parent = <&intc>;
-					interrupts = <4>;
-				};
-			};
-
-			sys: sys-ctrl@e00000 {
-				compatible = "oxsemi,ox820-sys-ctrl", "syscon", "simple-mfd";
-				reg = <0xe00000 0x200000>;
-
-				reset: reset-controller {
-					compatible = "oxsemi,ox820-reset", "oxsemi,ox810se-reset";
-					#reset-cells = <1>;
-				};
-
-				stdclk: stdclk {
-					compatible = "oxsemi,ox820-stdclk", "oxsemi,ox810se-stdclk";
-					#clock-cells = <1>;
-				};
-			};
-		};
-
-		apb-bridge@47000000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "simple-bus";
-			ranges = <0 0x47000000 0x1000000>;
-
-			scu: scu@0 {
-				compatible = "arm,arm11mp-scu";
-				reg = <0x0 0x100>;
-			};
-
-			local-timer@600 {
-				compatible = "arm,arm11mp-twd-timer";
-				reg = <0x600 0x20>;
-				interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3)|IRQ_TYPE_LEVEL_HIGH)>;
-				clocks = <&armclk>;
-			};
-
-			gic: gic@1000 {
-				compatible = "arm,arm11mp-gic";
-				interrupt-controller;
-				#interrupt-cells = <3>;
-				reg = <0x1000 0x1000>,
-				      <0x100 0x500>;
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
deleted file mode 100644
index 138d6478ac84..000000000000
--- a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
+++ /dev/null
@@ -1,937 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
-#include "qcom-msm8660.dtsi"
-
-/ {
-	model = "Qualcomm APQ8060 Dragonboard";
-	compatible = "qcom,apq8060-dragonboard", "qcom,msm8660";
-
-	aliases {
-		serial0 = &gsbi12_serial;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	regulators {
-		compatible = "simple-bus";
-
-		/* Main power of the board: 3.7V */
-		vph: regulator-fixed {
-			compatible = "regulator-fixed";
-			regulator-min-microvolt = <3700000>;
-			regulator-max-microvolt = <3700000>;
-			regulator-name = "VPH";
-			regulator-type = "voltage";
-			regulator-always-on;
-			regulator-boot-on;
-		};
-
-		/* GPIO controlled ethernet power regulator */
-		dragon_veth: xc622a331mrg {
-			compatible = "regulator-fixed";
-			regulator-name = "XC6222A331MR-G";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			vin-supply = <&vph>;
-			gpio = <&pm8058_gpio 40 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			pinctrl-names = "default";
-			pinctrl-0 = <&dragon_veth_gpios>;
-			regulator-always-on;
-		};
-
-		/* VDDvario fixed regulator */
-		dragon_vario: nds332p {
-			compatible = "regulator-fixed";
-			regulator-name = "NDS332P";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			vin-supply = <&pm8058_s3>;
-		};
-
-		/* This is a levelshifter for SDCC5 */
-		dragon_vio_txb: txb0104rgyr {
-			compatible = "regulator-fixed";
-			regulator-name = "Dragon SDCC levelshifter";
-			vin-supply = <&pm8058_l14>;
-			regulator-always-on;
-		};
-	};
-
-	/*
-	 * Capella CM3605 light and proximity sensor mounted directly
-	 * on the sensor board.
-	 */
-	cm3605 {
-		compatible = "capella,cm3605";
-		vdd-supply = <&pm8058_l14>; // 2.85V
-		aset-gpios = <&pm8058_gpio 35 GPIO_ACTIVE_LOW>;
-		capella,aset-resistance-ohms = <100000>;
-		/* Trig on both edges - getting close or far away */
-		interrupts-extended = <&pm8058_gpio 34 IRQ_TYPE_EDGE_BOTH>;
-		/* MPP05 analog input to the XOADC */
-		io-channels = <&xoadc 0x00 0x05>;
-		io-channel-names = "aout";
-		pinctrl-names = "default";
-		pinctrl-0 = <&dragon_cm3605_gpios>, <&dragon_cm3605_mpps>;
-	};
-
-	soc {
-		pinctrl@800000 {
-			/* eMMC pins, all 8 data lines connected */
-			dragon_sdcc1_pins: sdcc1 {
-				mux {
-					pins = "gpio159", "gpio160", "gpio161",
-					     "gpio162", "gpio163", "gpio164",
-					     "gpio165", "gpio166", "gpio167",
-					     "gpio168";
-					     function = "sdc1";
-				};
-				clk {
-					pins = "gpio167"; /* SDC1 CLK */
-					drive-strength = <16>;
-					bias-disable;
-				};
-				cmd {
-					pins = "gpio168"; /* SDC1 CMD */
-					drive-strength = <10>;
-					bias-pull-up;
-				};
-				data {
-					/* SDC1 D0 to D7 */
-					pins = "gpio159", "gpio160", "gpio161", "gpio162",
-					     "gpio163", "gpio164", "gpio165", "gpio166";
-					drive-strength = <10>;
-					bias-pull-up;
-				};
-			};
-
-			/*
-			 * The SDCC3 pins are hardcoded (non-muxable) but need some pin
-			 * configuration.
-			 */
-			dragon_sdcc3_pins: sdcc3 {
-				clk {
-					pins = "sdc3_clk";
-					drive-strength = <8>;
-					bias-disable;
-				};
-				cmd {
-					pins = "sdc3_cmd";
-					drive-strength = <8>;
-					bias-pull-up;
-				};
-				data {
-					pins = "sdc3_data";
-					drive-strength = <8>;
-					bias-pull-up;
-				};
-			};
-
-			/* Second SD card slot pins */
-			dragon_sdcc5_pins: sdcc5 {
-				mux {
-					pins = "gpio95", "gpio96", "gpio97",
-					    "gpio98", "gpio99", "gpio100";
-					function = "sdc5";
-				};
-				clk {
-					pins = "gpio97"; /* SDC5 CLK */
-					drive-strength = <16>;
-					bias-disable;
-				};
-				cmd {
-					pins = "gpio95"; /* SDC5 CMD */
-					drive-strength = <10>;
-					bias-pull-up;
-				};
-				data {
-					/* SDC5 D0 to D3 */
-					pins = "gpio96", "gpio98", "gpio99", "gpio100";
-					drive-strength = <10>;
-					bias-pull-up;
-				};
-			};
-
-			dragon_gsbi8_i2c_pins: gsbi8_i2c {
-				mux {
-					pins = "gpio64", "gpio65";
-					function = "gsbi8";
-				};
-				pinconf {
-					pins = "gpio64", "gpio65";
-					drive-strength = <16>;
-					/* These have external pull-up 2.2kOhm to 1.8V */
-					bias-disable;
-				};
-			};
-
-			dragon_gsbi12_i2c_pins: gsbi12_i2c {
-				mux {
-					pins = "gpio115", "gpio116";
-					function = "gsbi12";
-				};
-				pinconf {
-					pins = "gpio115", "gpio116";
-					drive-strength = <16>;
-					/* These have external pull-up 4.7kOhm to 1.8V */
-					bias-disable;
-				};
-			};
-
-			/* Primary serial port uart 0 pins */
-			dragon_gsbi12_serial_pins: gsbi12_serial {
-				mux {
-					pins = "gpio117", "gpio118";
-					function = "gsbi12";
-				};
-				tx {
-					pins = "gpio117";
-					drive-strength = <8>;
-					bias-disable;
-				};
-				rx {
-					pins = "gpio118";
-					drive-strength = <2>;
-					bias-pull-up;
-				};
-			};
-
-			dragon_ebi2_pins: ebi2 {
-				/*
-				 * Pins used by EBI2 on the Dragonboard, actually only
-				 * CS2 is used by a real peripheral. CS0 is just
-				 * routed to a test point.
-				 */
-				mux0 {
-					pins =
-					    /* "gpio39", CS1A_N this is not good to mux */
-					    "gpio40", /* CS2A_N */
-					    "gpio134"; /* CS0_N testpoint TP29 */
-					function = "ebi2cs";
-				};
-				mux1 {
-					pins =
-					    /* EBI2_ADDR_7 downto EBI2_ADDR_0 address bus */
-					    "gpio123", "gpio124", "gpio125", "gpio126",
-					    "gpio127", "gpio128", "gpio129", "gpio130",
-					    /* EBI2_DATA_15 downto EBI2_DATA_0 data bus */
-					    "gpio135", "gpio136", "gpio137", "gpio138",
-					    "gpio139", "gpio140", "gpio141", "gpio142",
-					    "gpio143", "gpio144", "gpio145", "gpio146",
-					    "gpio147", "gpio148", "gpio149", "gpio150",
-					    "gpio151", /* EBI2_OE_N */
-					    "gpio153", /* EBI2_ADV */
-					    "gpio157"; /* EBI2_WE_N */
-					function = "ebi2";
-				};
-			};
-
-			/* Interrupt line for the KXSD9 accelerometer */
-			dragon_kxsd9_gpios: kxsd9 {
-				irq {
-					pins = "gpio57"; /* IRQ line */
-					bias-pull-up;
-				};
-			};
-		};
-
-		qcom,ssbi@500000 {
-			pmic@0 {
-				keypad@148 {
-					linux,keymap = <
-					MATRIX_KEY(0, 0, KEY_MENU)
-					MATRIX_KEY(0, 2, KEY_1)
-					MATRIX_KEY(0, 3, KEY_4)
-					MATRIX_KEY(0, 4, KEY_7)
-					MATRIX_KEY(1, 0, KEY_UP)
-					MATRIX_KEY(1, 1, KEY_LEFT)
-					MATRIX_KEY(1, 2, KEY_DOWN)
-					MATRIX_KEY(1, 3, KEY_5)
-					MATRIX_KEY(1, 3, KEY_8)
-					MATRIX_KEY(2, 0, KEY_HOME)
-					MATRIX_KEY(2, 1, KEY_REPLY)
-					MATRIX_KEY(2, 2, KEY_2)
-					MATRIX_KEY(2, 3, KEY_6)
-					MATRIX_KEY(3, 0, KEY_VOLUMEUP)
-					MATRIX_KEY(3, 1, KEY_RIGHT)
-					MATRIX_KEY(3, 2, KEY_3)
-					MATRIX_KEY(3, 3, KEY_9)
-					MATRIX_KEY(3, 4, KEY_SWITCHVIDEOMODE)
-					MATRIX_KEY(4, 0, KEY_VOLUMEDOWN)
-					MATRIX_KEY(4, 1, KEY_BACK)
-					MATRIX_KEY(4, 2, KEY_CAMERA)
-					MATRIX_KEY(4, 3, KEY_KBDILLUMTOGGLE)
-					>;
-					keypad,num-rows = <6>;
-					keypad,num-columns = <5>;
-				};
-
-				gpio@150 {
-					dragon_ethernet_gpios: ethernet-gpios {
-						pinconf {
-							pins = "gpio7";
-							function = "normal";
-							input-enable;
-							bias-disable;
-							power-source = <PM8058_GPIO_S3>;
-						};
-					};
-					dragon_bmp085_gpios: bmp085-gpios {
-						pinconf {
-							pins = "gpio16";
-							function = "normal";
-							input-enable;
-							bias-disable;
-							power-source = <PM8058_GPIO_S3>;
-						};
-					};
-					dragon_mpu3050_gpios: mpu3050-gpios {
-						pinconf {
-							pins = "gpio17";
-							function = "normal";
-							input-enable;
-							bias-disable;
-							power-source = <PM8058_GPIO_S3>;
-						};
-					};
-					dragon_sdcc3_gpios: sdcc3-gpios {
-						pinconf {
-							pins = "gpio22";
-							function = "normal";
-							input-enable;
-							bias-disable;
-							power-source = <PM8058_GPIO_S3>;
-						};
-					};
-					dragon_sdcc5_gpios: sdcc5-gpios {
-						pinconf {
-							pins = "gpio26";
-							function = "normal";
-							input-enable;
-							bias-pull-up;
-							qcom,pull-up-strength = <PMIC_GPIO_PULL_UP_30>;
-							power-source = <PM8058_GPIO_S3>;
-						};
-					};
-					dragon_ak8975_gpios: ak8975-gpios {
-						pinconf {
-							pins = "gpio33";
-							function = "normal";
-							input-enable;
-							bias-disable;
-							power-source = <PM8058_GPIO_S3>;
-						};
-					};
-					dragon_cm3605_gpios: cm3605-gpios {
-						/* Pin 34 connected to the proxy IRQ */
-						pinconf_gpio34 {
-							pins = "gpio34";
-							function = "normal";
-							input-enable;
-							bias-disable;
-							power-source = <PM8058_GPIO_S3>;
-						};
-						/* Pin 35 connected to ASET */
-						pinconf_gpio35 {
-							pins = "gpio35";
-							function = "normal";
-							output-high;
-							bias-disable;
-							power-source = <PM8058_GPIO_S3>;
-						};
-					};
-					dragon_veth_gpios: veth-gpios {
-						pinconf {
-							pins = "gpio40";
-							function = "normal";
-							bias-disable;
-							drive-push-pull;
-						};
-					};
-				};
-
-				mpps@50 {
-					dragon_cm3605_mpps: cm3605-mpps-state {
-						mpp5 {
-							pins = "mpp5";
-							function = "analog";
-							input-enable;
-							bias-high-impedance;
-							/* Let's use channel 5 */
-							qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH5>;
-							power-source = <PM8058_GPIO_S3>;
-						};
-					};
-				};
-
-				xoadc@197 {
-					/* Reference voltage 2.2 V */
-					xoadc-ref-supply = <&pm8058_l18>;
-
-					/* Board-specific channels */
-					mpp5@5 {
-						/* Connected to AOUT of ALS sensor */
-						reg = <0x00 0x05>;
-					};
-					mpp6@6 {
-						/* Connected to test point TP43 */
-						reg = <0x00 0x06>;
-					};
-					mpp7@7 {
-						/* Connected to battery thermistor */
-						reg = <0x00 0x07>;
-					};
-					mpp8@8 {
-						/* Connected to battery ID detector */
-						reg = <0x00 0x08>;
-					};
-					mpp9@9 {
-						/* Connected to XO thermistor */
-						reg = <0x00 0x09>;
-					};
-				};
-
-				led@48 {
-					/*
-					 * The keypad LED @0x48 is routed to
-					 * the sensor board where it is
-					 * connected to an infrared LED
-					 * SFH4650 (60mW, @850nm) next to the
-					 * ambient light and proximity sensor
-					 * Capella Microsystems CM3605.
-					 */
-					compatible = "qcom,pm8058-keypad-led";
-					reg = <0x48>;
-					label = "pm8058:infrared:proximitysensor";
-					default-state = "off";
-					linux,default-trigger = "cm3605";
-				};
-				led@131 {
-					compatible = "qcom,pm8058-led";
-					reg = <0x131>;
-					label = "pm8058:red";
-					default-state = "off";
-				};
-				led@132 {
-					/*
-					 * This is actually green too on my
-					 * board, but documented as yellow.
-					 */
-					compatible = "qcom,pm8058-led";
-					reg = <0x132>;
-					label = "pm8058:yellow";
-					default-state = "off";
-					linux,default-trigger = "mmc0";
-				};
-				led@133 {
-					compatible = "qcom,pm8058-led";
-					reg = <0x133>;
-					label = "pm8058:green";
-					default-state = "on";
-					linux,default-trigger = "heartbeat";
-				};
-			};
-		};
-
-		gsbi@19800000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C>;
-
-			i2c@19880000 {
-				status = "okay";
-				pinctrl-names = "default";
-				pinctrl-0 = <&dragon_gsbi8_i2c_pins>;
-
-				eeprom@52 {
-					/* A 16KiB Platform ID EEPROM on the CPU carrier board */
-					compatible = "atmel,24c128";
-					reg = <0x52>;
-					vcc-supply = <&pm8058_s3>;
-					pagesize = <64>;
-				};
-				wm8903: wm8903@1a {
-					/* This Woolfson Micro device has an unrouted interrupt line */
-					compatible = "wlf,wm8903";
-					reg = <0x1a>;
-
-					AVDD-supply = <&pm8058_l16>;
-					CPVDD-supply = <&pm8058_l16>;
-					DBVDD-supply = <&pm8058_s3>;
-					DCVDD-supply = <&pm8058_l0>;
-
-					gpio-controller;
-					#gpio-cells = <2>;
-
-					micdet-cfg = <0>;
-					micdet-delay = <100>;
-					gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
-				};
-			};
-		};
-
-		gsbi@19c00000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
-
-			serial@19c40000 {
-				status = "okay";
-				pinctrl-names = "default";
-				pinctrl-0 = <&dragon_gsbi12_serial_pins>;
-			};
-
-			i2c@19c80000 {
-				status = "okay";
-				pinctrl-names = "default";
-				pinctrl-0 = <&dragon_gsbi12_i2c_pins>;
-
-				ak8975@c {
-					compatible = "asahi-kasei,ak8975";
-					reg = <0x0c>;
-					interrupt-parent = <&pm8058_gpio>;
-					interrupts = <33 IRQ_TYPE_EDGE_RISING>;
-					pinctrl-names = "default";
-					pinctrl-0 = <&dragon_ak8975_gpios>;
-					vid-supply = <&pm8058_lvs0>; // 1.8V
-					vdd-supply = <&pm8058_l14>; // 2.85V
-				};
-				bmp085@77 {
-					compatible = "bosch,bmp085";
-					reg = <0x77>;
-					interrupt-parent = <&pm8058_gpio>;
-					interrupts = <16 IRQ_TYPE_EDGE_RISING>;
-					reset-gpios = <&tlmm 86 GPIO_ACTIVE_LOW>;
-					pinctrl-names = "default";
-					pinctrl-0 = <&dragon_bmp085_gpios>;
-					vddd-supply = <&pm8058_lvs0>; // 1.8V
-					vdda-supply = <&pm8058_l14>; // 2.85V
-				};
-				mpu3050@68 {
-					compatible = "invensense,mpu3050";
-					reg = <0x68>;
-					/*
-					 * GPIO17 is pulled high by a 10k
-					 * resistor to VLOGIC so needs to be
-					 * active low/falling edge.
-					 */
-					interrupts-extended = <&pm8058_gpio 17 IRQ_TYPE_EDGE_FALLING>;
-					pinctrl-names = "default";
-					pinctrl-0 = <&dragon_mpu3050_gpios>;
-					vlogic-supply = <&pm8058_lvs0>; // 1.8V
-					vdd-supply = <&pm8058_l14>; // 2.85V
-
-					/*
-					 * The MPU-3050 acts as a hub for the
-					 * accelerometer.
-					 */
-					i2c-gate {
-						#address-cells = <1>;
-						#size-cells = <0>;
-
-						kxsd9@18 {
-							compatible = "kionix,kxsd9";
-							reg = <0x18>;
-							interrupt-parent = <&tlmm>;
-							interrupts = <57 IRQ_TYPE_EDGE_FALLING>;
-							pinctrl-names = "default";
-							pinctrl-0 = <&dragon_kxsd9_gpios>;
-							iovdd-supply = <&pm8058_lvs0>; // 1.8V
-							vdd-supply = <&pm8058_l14>; // 2.85V
-						};
-					};
-				};
-			};
-		};
-
-		external-bus@1a100000 {
-			/* The EBI2 will instantiate first, then populate its children */
-			status = "okay";
-			pinctrl-names = "default";
-			pinctrl-0 = <&dragon_ebi2_pins>;
-
-			/*
-			 * An on-board SMSC LAN9221 chip for "debug ethernet",
-			 * which is actually just an ordinary ethernet on the
-			 * EBI2. This has a 25MHz chrystal next to it, so no
-			 * clocking is needed.
-			 */
-			ethernet@2,0 {
-				compatible = "smsc,lan9221", "smsc,lan9115";
-				reg = <2 0x0 0x100>;
-				/*
-				 * The second interrupt is the PME interrupt
-				 * for network wakeup, connected to the TLMM.
-				 */
-				interrupts-extended = <&pm8058_gpio 7 IRQ_TYPE_EDGE_FALLING>,
-						    <&tlmm 29 IRQ_TYPE_EDGE_RISING>;
-				reset-gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
-				vdd33a-supply = <&dragon_veth>;
-				vddvario-supply = <&dragon_vario>;
-				pinctrl-names = "default";
-				pinctrl-0 = <&dragon_ethernet_gpios>;
-				phy-mode = "mii";
-				reg-io-width = <2>;
-				smsc,force-external-phy;
-				smsc,irq-push-pull;
-
-				/*
-				 * SLOW chipselect config
-				 * Delay 9 cycles (140ns@64MHz) between SMSC
-				 * LAN9221 Ethernet controller reads and writes
-				 * on CS2.
-				 */
-				qcom,xmem-recovery-cycles = <0>;
-				qcom,xmem-write-hold-cycles = <3>;
-				qcom,xmem-write-delta-cycles = <31>;
-				qcom,xmem-read-delta-cycles = <28>;
-				qcom,xmem-write-wait-cycles = <9>;
-				qcom,xmem-read-wait-cycles = <9>;
-			};
-		};
-
-		rpm@104000 {
-			/*
-			 * Set up of the PMIC RPM regulators for this board
-			 * PM8901 supplies "preliminary regulators" whatever
-			 * that means
-			 */
-			pm8901-regulators {
-				vdd_l0-supply = <&pm8901_s4>;
-				vdd_l1-supply = <&vph>;
-				vdd_l2-supply = <&vph>;
-				vdd_l3-supply = <&vph>;
-				vdd_l4-supply = <&vph>;
-				vdd_l5-supply = <&vph>;
-				vdd_l6-supply = <&vph>;
-				/* vdd_s0-supply, vdd_s1-supply: SAW regulators */
-				vdd_s2-supply = <&vph>;
-				vdd_s3-supply = <&vph>;
-				vdd_s4-supply = <&vph>;
-				lvs0_in-supply = <&pm8058_s3>;
-				lvs1_in-supply = <&pm8901_s4>;
-				lvs2_in-supply = <&pm8058_l0>;
-				lvs3_in-supply = <&pm8058_s2>;
-				mvs_in-supply = <&pm8058_s3>;
-
-				l0 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-				l1 {
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-					bias-pull-down;
-				};
-				l2 {
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <3300000>;
-					bias-pull-down;
-				};
-				l3 {
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-					bias-pull-down;
-				};
-				l4 {
-					regulator-min-microvolt = <2600000>;
-					regulator-max-microvolt = <2600000>;
-					bias-pull-down;
-				};
-				l5 {
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <2850000>;
-					bias-pull-down;
-				};
-				l6 {
-					regulator-min-microvolt = <2200000>;
-					regulator-max-microvolt = <2200000>;
-					bias-pull-down;
-				};
-
-				/* s0 and s1 are SAW regulators controlled over SPM */
-				s2 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-				s3 {
-					regulator-min-microvolt = <1100000>;
-					regulator-max-microvolt = <1100000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-				s4 {
-					regulator-min-microvolt = <1225000>;
-					regulator-max-microvolt = <1225000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				/* LVS0 thru 3 and mvs are just switches */
-				lvs0 {
-					regulator-always-on;
-				};
-				lvs1 { };
-				lvs2 { };
-				lvs3 { };
-				mvs { };
-
-			};
-
-			pm8058-regulators {
-				vdd_l0_l1_lvs-supply = <&pm8058_s3>;
-				vdd_l2_l11_l12-supply = <&vph>;
-				vdd_l3_l4_l5-supply = <&vph>;
-				vdd_l6_l7-supply = <&vph>;
-				vdd_l8-supply = <&vph>;
-				vdd_l9-supply = <&vph>;
-				vdd_l10-supply = <&vph>;
-				vdd_l13_l16-supply = <&pm8058_s4>;
-				vdd_l14_l15-supply = <&vph>;
-				vdd_l17_l18-supply = <&vph>;
-				vdd_l19_l20-supply = <&vph>;
-				vdd_l21-supply = <&pm8058_s3>;
-				vdd_l22-supply = <&pm8058_s3>;
-				vdd_l23_l24_l25-supply = <&pm8058_s3>;
-				vdd_s0-supply = <&vph>;
-				vdd_s1-supply = <&vph>;
-				vdd_s2-supply = <&vph>;
-				vdd_s3-supply = <&vph>;
-				vdd_s4-supply = <&vph>;
-				vdd_ncp-supply = <&vph>;
-
-				l0 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-				l1 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-				l2 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <2600000>;
-					bias-pull-down;
-				};
-				l3 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-				l4 {
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <2850000>;
-					bias-pull-down;
-				};
-				l5 {
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <2850000>;
-					bias-pull-down;
-				};
-				l6 {
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3600000>;
-					bias-pull-down;
-				};
-				l7 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-				l8 {
-					regulator-min-microvolt = <2900000>;
-					regulator-max-microvolt = <3050000>;
-					bias-pull-down;
-				};
-				l9 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-				l10 {
-					regulator-min-microvolt = <2600000>;
-					regulator-max-microvolt = <2600000>;
-					bias-pull-down;
-				};
-				l11 {
-					regulator-min-microvolt = <1500000>;
-					regulator-max-microvolt = <1500000>;
-					bias-pull-down;
-				};
-				l12 {
-					regulator-min-microvolt = <2900000>;
-					regulator-max-microvolt = <2900000>;
-					bias-pull-down;
-				};
-				l13 {
-					regulator-min-microvolt = <2050000>;
-					regulator-max-microvolt = <2050000>;
-					bias-pull-down;
-				};
-				l14 {
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <2850000>;
-				};
-				l15 {
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <2850000>;
-					bias-pull-down;
-				};
-				l16 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-					regulator-always-on;
-				};
-				l17 {
-					// 1.5V according to schematic
-					regulator-min-microvolt = <2600000>;
-					regulator-max-microvolt = <2600000>;
-					bias-pull-down;
-				};
-				l18 {
-					regulator-min-microvolt = <2200000>;
-					regulator-max-microvolt = <2200000>;
-					bias-pull-down;
-				};
-				l19 {
-					regulator-min-microvolt = <2500000>;
-					regulator-max-microvolt = <2500000>;
-					bias-pull-down;
-				};
-				l20 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-				l21 {
-					// 1.1 V according to schematic
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-					regulator-always-on;
-				};
-				l22 {
-					// 1.2 V according to schematic
-					regulator-min-microvolt = <1150000>;
-					regulator-max-microvolt = <1150000>;
-					bias-pull-down;
-				};
-				l23 {
-					// Unused
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-				l24 {
-					// Unused
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-				l25 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-
-				s0 {
-					// regulator-min-microvolt = <500000>;
-					// regulator-max-microvolt = <1325000>;
-					regulator-min-microvolt = <1100000>;
-					regulator-max-microvolt = <1100000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-				s1 {
-					// regulator-min-microvolt = <500000>;
-					// regulator-max-microvolt = <1250000>;
-					regulator-min-microvolt = <1100000>;
-					regulator-max-microvolt = <1100000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-				s2 {
-					// 1.3 V according to schematic
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1400000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-				s3 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					qcom,switch-mode-frequency = <1600000>;
-					regulator-always-on;
-					bias-pull-down;
-				};
-				s4 {
-					regulator-min-microvolt = <2200000>;
-					regulator-max-microvolt = <2200000>;
-					qcom,switch-mode-frequency = <1600000>;
-					regulator-always-on;
-					bias-pull-down;
-				};
-
-				/* LVS0 and LVS1 are just switches */
-				lvs0 {
-					bias-pull-down;
-				};
-				lvs1 {
-					bias-pull-down;
-				};
-
-				ncp {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					qcom,switch-mode-frequency = <1600000>;
-				};
-			};
-		};
-		amba {
-			/* Internal 3.69 GiB eMMC */
-			mmc@12400000 {
-				status = "okay";
-				pinctrl-names = "default";
-				pinctrl-0 = <&dragon_sdcc1_pins>;
-				vmmc-supply = <&pm8901_l5>;
-				vqmmc-supply = <&pm8901_lvs0>;
-			};
-
-			/* External micro SD card, directly connected, pulled up to 2.85 V */
-			mmc@12180000 {
-				status = "okay";
-				/* Enable SSBI GPIO 22 as input, use for card detect */
-				pinctrl-names = "default";
-				pinctrl-0 = <&dragon_sdcc3_pins>, <&dragon_sdcc3_gpios>;
-				cd-gpios = <&pm8058_gpio 22 GPIO_ACTIVE_LOW>;
-				wp-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
-				vmmc-supply = <&pm8058_l14>;
-			};
-
-			/*
-			 * Second external micro SD card, using two TXB104RGYR levelshifters
-			 * to lift from 1.8 V to 2.85 V
-			 */
-			mmc@12200000 {
-				status = "okay";
-				/* Enable SSBI GPIO 26 as input, use for card detect */
-				pinctrl-names = "default";
-				pinctrl-0 = <&dragon_sdcc5_pins>, <&dragon_sdcc5_gpios>;
-				cd-gpios = <&pm8058_gpio 26 GPIO_ACTIVE_LOW>;
-				wp-gpios = <&tlmm 106 GPIO_ACTIVE_HIGH>;
-				vmmc-supply = <&pm8058_l14>;
-				vqmmc-supply = <&dragon_vio_txb>;
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
deleted file mode 100644
index ca9f73528196..000000000000
--- a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
+++ /dev/null
@@ -1,358 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-apq8064-v2.0.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-/ {
-	model = "Asus Nexus7(flo)";
-	compatible = "asus,nexus7-flo", "qcom,apq8064";
-
-	aliases {
-		serial0 = &gsbi7_serial;
-		serial1 = &gsbi6_serial;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	reserved-memory {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		ramoops@88d00000{
-			compatible = "ramoops";
-			reg = <0x88d00000 0x100000>;
-			record-size     = <0x00020000>;
-			console-size    = <0x00020000>;
-			ftrace-size     = <0x00020000>;
-		};
-	};
-
-	ext_3p3v: regulator-fixed@1 {
-		compatible = "regulator-fixed";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-name = "ext_3p3v";
-		regulator-type = "voltage";
-		startup-delay-us = <0>;
-		gpio = <&tlmm_pinmux 77 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-		regulator-boot-on;
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		volume_up {
-			label = "Volume Up";
-			gpios = <&pm8921_gpio 4 GPIO_ACTIVE_HIGH>;
-			linux,code = <KEY_VOLUMEUP>;
-		};
-		volume_down {
-			label = "Volume Down";
-			gpios = <&pm8921_gpio 38 GPIO_ACTIVE_HIGH>;
-			linux,code = <KEY_VOLUMEDOWN>;
-		};
-	};
-
-	soc {
-		rpm@108000 {
-			regulators {
-				vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
-				vin_lvs1_3_6-supply = <&pm8921_s4>;
-				vin_lvs4_5_7-supply = <&pm8921_s4>;
-
-
-				vdd_l24-supply = <&pm8921_s1>;
-				vdd_l25-supply = <&pm8921_s1>;
-				vin_lvs2-supply = <&pm8921_s1>;
-
-				vdd_l26-supply = <&pm8921_s7>;
-				vdd_l27-supply = <&pm8921_s7>;
-				vdd_l28-supply = <&pm8921_s7>;
-
-				vdd_ncp-supply = <&pm8921_l6>;
-
-				/* Buck SMPS */
-				s1 {
-					regulator-always-on;
-					regulator-min-microvolt = <1225000>;
-					regulator-max-microvolt = <1225000>;
-					qcom,switch-mode-frequency = <3200000>;
-					bias-pull-down;
-				};
-
-				/* msm otg HSUSB_VDDCX */
-				s3 {
-					regulator-min-microvolt = <500000>;
-					regulator-max-microvolt = <1150000>;
-					qcom,switch-mode-frequency = <4800000>;
-				};
-
-				/*
-				 * msm_sdcc.1-sdc-vdd_io
-				 * tabla2x-slim-CDC_VDDA_RX
-				 * tabla2x-slim-CDC_VDDA_TX
-				 * tabla2x-slim-CDC_VDD_CP
-				 * tabla2x-slim-VDDIO_CDC
-				 */
-				s4 {
-					regulator-min-microvolt	= <1800000>;
-					regulator-max-microvolt	= <1800000>;
-					qcom,switch-mode-frequency = <3200000>;
-					regulator-always-on;
-				};
-
-				s7 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <3200000>;
-				};
-
-				/* mipi_dsi.1-dsi1_pll_vdda */
-				l2 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					regulator-always-on;
-				};
-
-				/* msm_otg-HSUSB_3p3 */
-				l3 {
-					regulator-min-microvolt = <3075000>;
-					regulator-max-microvolt = <3075000>;
-					bias-pull-down;
-				};
-
-				/* msm_otg-HSUSB_1p8 */
-				l4 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				/* msm_sdcc.1-sdc_vdd */
-				l5 {
-					regulator-min-microvolt = <2950000>;
-					regulator-max-microvolt = <2950000>;
-					regulator-always-on;
-					bias-pull-down;
-				};
-
-				l6 {
-					regulator-min-microvolt = <2950000>;
-					regulator-max-microvolt = <2950000>;
-				};
-
-				/* mipi_dsi.1-dsi1_avdd */
-				l11 {
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-					regulator-always-on;
-				};
-
-				/* pwm_power for backlight */
-				l17 {
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-					regulator-always-on;
-				};
-
-				/* camera, qdsp6 */
-				l23 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				/*
-				 * tabla2x-slim-CDC_VDDA_A_1P2V
-				 * tabla2x-slim-VDDD_CDC_D
-				 */
-				l25 {
-					regulator-min-microvolt = <1250000>;
-					regulator-max-microvolt = <1250000>;
-					bias-pull-down;
-				};
-
-				lvs1 {
-					bias-pull-down;
-				};
-
-				lvs4 {
-					bias-pull-down;
-				};
-
-				lvs5 {
-					bias-pull-down;
-				};
-
-				lvs6 {
-					bias-pull-down;
-				};
-				/*
-				 * mipi_dsi.1-dsi1_vddio
-				 * pil_riva-pll_vdd
-				 */
-				lvs7 {
-					bias-pull-down;
-				};
-			};
-		};
-
-		mdp@5100000 {
-			status = "okay";
-			ports {
-				port@1 {
-					mdp_dsi1_out: endpoint {
-						remote-endpoint = <&dsi0_in>;
-					};
-				};
-			};
-		};
-
-		dsi0: dsi@4700000 {
-			status = "okay";
-			vdda-supply = <&pm8921_l2>;/*VDD_MIPI1 to 4*/
-			vdd-supply = <&pm8921_l8>;
-			vddio-supply = <&pm8921_lvs7>;
-			avdd-supply = <&pm8921_l11>;
-
-			panel@0 {
-				reg = <0>;
-				compatible = "jdi,lt070me05000";
-
-				vddp-supply = <&pm8921_l17>;
-				iovcc-supply = <&pm8921_lvs7>;
-
-				enable-gpios = <&pm8921_gpio 36 GPIO_ACTIVE_HIGH>;
-				reset-gpios = <&tlmm_pinmux 54 GPIO_ACTIVE_LOW>;
-				dcdc-en-gpios = <&pm8921_gpio 23 GPIO_ACTIVE_HIGH>;
-
-				port {
-					panel_in: endpoint {
-						remote-endpoint = <&dsi0_out>;
-					};
-				};
-			};
-			ports {
-				port@0 {
-					dsi0_in: endpoint {
-						remote-endpoint = <&mdp_dsi1_out>;
-					};
-				};
-
-				port@1 {
-					dsi0_out: endpoint {
-						remote-endpoint = <&panel_in>;
-						data-lanes = <0 1 2 3>;
-					};
-				};
-			};
-		};
-
-		dsi-phy@4700200 {
-			status = "okay";
-			vddio-supply = <&pm8921_lvs7>;/*VDD_PLL2_1 to 7*/
-		};
-
-		gsbi@16200000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C>;
-			i2c@16280000 {
-				status = "okay";
-				clock-frequency = <200000>;
-				pinctrl-0 = <&i2c3_pins>;
-				pinctrl-names = "default";
-
-				trackpad@10 {
-					compatible = "elan,ekth3500";
-					reg = <0x10>;
-					interrupt-parent = <&tlmm_pinmux>;
-					interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
-				};
-			};
-		};
-
-
-		gsbi@12440000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C>;
-
-			i2c@12460000 {
-				status = "okay";
-				clock-frequency = <200000>;
-				pinctrl-0 = <&i2c1_pins>;
-				pinctrl-names = "default";
-
-				eeprom@52 {
-					compatible = "atmel,24c128";
-					reg = <0x52>;
-					pagesize = <32>;
-				};
-
-				bq27541@55 {
-					compatible = "ti,bq27541";
-					reg = <0x55>;
-				};
-
-			};
-		};
-
-		gsbi@16500000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
-
-			serial@16540000 {
-				status = "okay";
-
-				pinctrl-names = "default";
-				pinctrl-0 = <&gsbi6_uart_4pins>;
-			};
-		};
-
-		gsbi@16600000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
-			serial@16640000 {
-				status = "okay";
-			};
-		};
-
-		/* OTG */
-		usb@12500000 {
-			status = "okay";
-			dr_mode = "otg";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l4>;
-				};
-			};
-		};
-
-		amba {
-			/* eMMC */
-			mmc@12400000 {
-				status = "okay";
-				vmmc-supply = <&pm8921_l5>;
-				vqmmc-supply = <&pm8921_s4>;
-			};
-		};
-
-		imem@2a03f000 {
-			compatible = "syscon", "simple-mfd";
-			reg = <0x2a03f000 0x1000>;
-
-			reboot-mode {
-				compatible = "syscon-reboot-mode";
-				offset = <0x65c>;
-
-				mode-normal	= <0x77665501>;
-				mode-bootloader	= <0x77665500>;
-				mode-recovery	= <0x77665502>;
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts b/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts
deleted file mode 100644
index e068a8d0adf0..000000000000
--- a/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts
+++ /dev/null
@@ -1,246 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-apq8064-v2.0.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-
-/ {
-	model = "CompuLab CM-QS600";
-	compatible = "qcom,apq8064-cm-qs600", "qcom,apq8064";
-
-	aliases {
-		serial0 = &gsbi7_serial;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	pwrseq {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-		compatible = "simple-bus";
-
-		sdcc4_pwrseq: sdcc4_pwrseq {
-			pinctrl-names = "default";
-			pinctrl-0 = <&wlan_default_gpios>;
-			compatible = "mmc-pwrseq-simple";
-			reset-gpios = <&pm8921_gpio 43 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	soc {
-		pinctrl@800000 {
-			card_detect: card_detect {
-				mux {
-					pins = "gpio26";
-					function = "gpio";
-					bias-disable;
-				};
-			};
-
-			pcie_pins: pcie_pinmux {
-				mux {
-					pins = "gpio27";
-					function = "gpio";
-				};
-				conf {
-					pins = "gpio27";
-					drive-strength = <12>;
-					bias-disable;
-				};
-			};
-		};
-
-		rpm@108000 {
-			regulators {
-				vin_lvs1_3_6-supply = <&pm8921_s4>;
-				vin_lvs2-supply = <&pm8921_s1>;
-				vin_lvs4_5_7-supply = <&pm8921_s4>;
-
-				vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
-				vdd_l24-supply = <&pm8921_s1>;
-				vdd_l25-supply = <&pm8921_s1>;
-				vdd_l26-supply = <&pm8921_s7>;
-				vdd_l27-supply = <&pm8921_s7>;
-				vdd_l28-supply = <&pm8921_s7>;
-
-
-				/* Buck SMPS */
-				s1 {
-					regulator-always-on;
-					regulator-min-microvolt = <1225000>;
-					regulator-max-microvolt = <1225000>;
-					qcom,switch-mode-frequency = <3200000>;
-					bias-pull-down;
-				};
-
-				s3 {
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1400000>;
-					qcom,switch-mode-frequency = <4800000>;
-				};
-
-				s4 {
-					regulator-min-microvolt	= <1800000>;
-					regulator-max-microvolt	= <1800000>;
-					qcom,switch-mode-frequency = <3200000>;
-				};
-
-				s7 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <3200000>;
-				};
-
-				l3 {
-					regulator-min-microvolt = <3050000>;
-					regulator-max-microvolt = <3300000>;
-					bias-pull-down;
-				};
-
-				l4 {
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				l5 {
-					regulator-min-microvolt = <2750000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-				};
-
-				l23 {
-					regulator-min-microvolt = <1700000>;
-					regulator-max-microvolt = <1900000>;
-					bias-pull-down;
-				};
-
-				pm8921_lvs6: lvs6 {
-					bias-pull-down;
-				};
-
-			};
-		};
-
-		gsbi@12440000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C>;
-
-			i2c@12460000 {
-				status = "okay";
-				clock-frequency = <200000>;
-
-				eeprom@50 {
-					compatible = "atmel,24c02";
-					reg = <0x50>;
-					pagesize = <32>;
-				};
-			};
-		};
-
-		gsbi@16600000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
-			serial@16640000 {
-				status = "okay";
-				pinctrl-names = "default";
-				pinctrl-0 = <&gsbi7_uart_2pins>;
-			};
-		};
-
-		/* OTG */
-		usb@12500000 {
-			status = "okay";
-			dr_mode = "otg";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l4>;
-				};
-			};
-		};
-
-		usb@12520000 {
-			status = "okay";
-			dr_mode = "host";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l23>;
-				};
-			};
-		};
-
-		usb@12530000 {
-			status = "okay";
-			dr_mode = "host";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l23>;
-				};
-			};
-		};
-
-		/* on board fixed 3.3v supply */
-		v3p3_fixed: v3p3 {
-			compatible = "regulator-fixed";
-			regulator-name = "PCIE V3P3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-		qcom,ssbi@500000 {
-			pmic@0 {
-				gpio@150 {
-					wlan_default_gpios: wlan-gpios {
-						pios {
-							pins = "gpio43";
-							function = "normal";
-							bias-disable;
-							power-source = <PM8921_GPIO_S4>;
-						};
-					};
-				};
-			};
-		};
-
-		pci@1b500000 {
-			status = "okay";
-			vdda-supply = <&pm8921_s3>;
-			vdda_phy-supply = <&pm8921_lvs6>;
-			vdda_refclk-supply = <&v3p3_fixed>;
-			pinctrl-0 = <&pcie_pins>;
-			pinctrl-names = "default";
-			perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
-		};
-
-		amba {
-			/* eMMC */
-			sdcc1: mmc@12400000 {
-				status = "okay";
-				vmmc-supply = <&pm8921_l5>;
-				vqmmc-supply = <&pm8921_s4>;
-			};
-
-			/* External micro SD card */
-			sdcc3: mmc@12180000 {
-				status = "okay";
-				vmmc-supply = <&v3p3_fixed>;
-				pinctrl-names	= "default";
-				pinctrl-0	= <&card_detect>;
-				cd-gpios	= <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
-			};
-			/* WLAN */
-			sdcc4: mmc@121c0000 {
-				status = "okay";
-				vmmc-supply = <&v3p3_fixed>;
-				vqmmc-supply = <&v3p3_fixed>;
-				mmc-pwrseq = <&sdcc4_pwrseq>;
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
deleted file mode 100644
index 2638b380be20..000000000000
--- a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
+++ /dev/null
@@ -1,381 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-apq8064-v2.0.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-
-/ {
-	model = "Qualcomm APQ8064/IFC6410";
-	compatible = "qcom,apq8064-ifc6410", "qcom,apq8064";
-
-	aliases {
-		serial0 = &gsbi7_serial;
-		serial1 = &gsbi6_serial;
-		i2c0 = &gsbi1_i2c;
-		i2c1 = &gsbi2_i2c;
-		i2c2 = &gsbi3_i2c;
-		i2c3 = &gsbi4_i2c;
-		spi0 = &gsbi5_spi;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	pwrseq {
-		compatible = "simple-bus";
-
-		sdcc4_pwrseq: sdcc4_pwrseq {
-			pinctrl-names = "default";
-			pinctrl-0 = <&wlan_default_gpios>;
-			compatible = "mmc-pwrseq-simple";
-			reset-gpios = <&pm8921_gpio 43 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&notify_led>;
-
-		led@1 {
-			label = "apq8064:green:user1";
-			gpios = <&pm8921_gpio 18 GPIO_ACTIVE_HIGH>;
-			default-state = "on";
-		};
-	};
-
-	hdmi-out {
-		compatible = "hdmi-connector";
-		type = "d";
-
-		port {
-			hdmi_con: endpoint {
-				remote-endpoint = <&hdmi_out>;
-			};
-		};
-	};
-
-	soc {
-		pinctrl@800000 {
-			card_detect: card_detect {
-				mux {
-					pins = "gpio26";
-					function = "gpio";
-					bias-disable;
-				};
-			};
-
-			pcie_pins: pcie_pinmux {
-				mux {
-					pins = "gpio27";
-					function = "gpio";
-				};
-				conf {
-					pins = "gpio27";
-					drive-strength = <12>;
-					bias-disable;
-				};
-			};
-		};
-
-		rpm@108000 {
-			regulators {
-				vin_lvs1_3_6-supply = <&pm8921_s4>;
-				vin_lvs2-supply = <&pm8921_s1>;
-				vin_lvs4_5_7-supply = <&pm8921_s4>;
-
-				vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
-				vdd_l24-supply = <&pm8921_s1>;
-				vdd_l25-supply = <&pm8921_s1>;
-				vdd_l26-supply = <&pm8921_s7>;
-				vdd_l27-supply = <&pm8921_s7>;
-				vdd_l28-supply = <&pm8921_s7>;
-
-
-				/* Buck SMPS */
-				s1 {
-					regulator-always-on;
-					regulator-min-microvolt = <1225000>;
-					regulator-max-microvolt = <1225000>;
-					qcom,switch-mode-frequency = <3200000>;
-					bias-pull-down;
-				};
-
-				s3 {
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1400000>;
-					qcom,switch-mode-frequency = <4800000>;
-				};
-
-				s4 {
-					regulator-min-microvolt	= <1800000>;
-					regulator-max-microvolt	= <1800000>;
-					qcom,switch-mode-frequency = <3200000>;
-				};
-
-				s7 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <3200000>;
-				};
-
-				l3 {
-					regulator-min-microvolt = <3050000>;
-					regulator-max-microvolt = <3300000>;
-					bias-pull-down;
-				};
-
-				l4 {
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				l5 {
-					regulator-min-microvolt = <2750000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-				};
-
-				l6 {
-					regulator-min-microvolt = <2950000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				l23 {
-					regulator-min-microvolt = <1700000>;
-					regulator-max-microvolt = <1900000>;
-					bias-pull-down;
-				};
-
-				lvs1 {
-					bias-pull-down;
-				};
-
-				lvs6 {
-					bias-pull-down;
-				};
-			};
-		};
-
-		ext_3p3v: regulator-fixed@1 {
-			compatible = "regulator-fixed";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-name = "ext_3p3v";
-			regulator-type = "voltage";
-			startup-delay-us = <0>;
-			gpio = <&tlmm_pinmux 77 GPIO_ACTIVE_HIGH>;
-			enable-active-high;
-			regulator-boot-on;
-		};
-
-		gsbi3: gsbi@16200000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C>;
-			i2c@16280000 {
-				status = "okay";
-			};
-		};
-
-		gsbi@16300000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C>;
-			/* CAM I2C MIPI-CSI connector */
-			i2c@16380000 {
-				status = "okay";
-			};
-		};
-
-		gsbi@12440000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C>;
-
-			i2c@12460000 {
-				status = "okay";
-				clock-frequency = <200000>;
-
-				eeprom@52 {
-					compatible = "atmel,24c128";
-					reg = <0x52>;
-					pagesize = <32>;
-				};
-			};
-		};
-
-		gsbi@1a200000 {
-			qcom,mode = <GSBI_PROT_SPI>;
-			status = "okay";
-			spi4: spi@1a280000 {
-				status = "okay";
-				num-cs = <1>;
-				cs-gpios = <&tlmm_pinmux 53 0>;
-			};
-		};
-
-		gsbi@16500000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_UART_W_FC>;
-
-			serial@16540000 {
-				status = "okay";
-				pinctrl-names = "default";
-				pinctrl-0 = <&gsbi6_uart_4pins>;
-			};
-		};
-
-		gsbi@16600000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
-			serial@16640000 {
-				status = "okay";
-				pinctrl-names = "default";
-				pinctrl-0 = <&gsbi7_uart_2pins>;
-			};
-		};
-
-		sata_phy0: phy@1b400000 {
-			status = "okay";
-		};
-
-		sata0: sata@29000000 {
-			status		= "okay";
-			target-supply	= <&pm8921_s4>;
-		};
-
-		/* OTG */
-		usb@12500000 {
-			status = "okay";
-			dr_mode = "otg";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l4>;
-				};
-			};
-		};
-
-		usb@12520000 {
-			status = "okay";
-			dr_mode = "host";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l23>;
-				};
-			};
-		};
-
-		usb@12530000 {
-			status = "okay";
-			dr_mode = "host";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l23>;
-				};
-			};
-		};
-
-		pci@1b500000 {
-			status = "okay";
-			vdda-supply = <&pm8921_s3>;
-			vdda_phy-supply = <&pm8921_lvs6>;
-			vdda_refclk-supply = <&ext_3p3v>;
-			pinctrl-0 = <&pcie_pins>;
-			pinctrl-names = "default";
-			perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
-		};
-
-		qcom,ssbi@500000 {
-			pmic@0 {
-				gpio@150 {
-					wlan_default_gpios: wlan-gpios {
-						pios {
-							pins = "gpio43";
-							function = "normal";
-							bias-disable;
-							power-source = <PM8921_GPIO_S4>;
-						};
-					};
-
-					notify_led: nled {
-						pios {
-							pins = "gpio18";
-							function = "normal";
-							bias-disable;
-							power-source = <PM8921_GPIO_S4>;
-						};
-					};
-				};
-			};
-		};
-
-		amba {
-			/* eMMC */
-			sdcc1: mmc@12400000 {
-				status = "okay";
-				vmmc-supply = <&pm8921_l5>;
-				vqmmc-supply = <&pm8921_s4>;
-			};
-
-			/* External micro SD card */
-			sdcc3: mmc@12180000 {
-				status = "okay";
-				vmmc-supply = <&pm8921_l6>;
-				pinctrl-names	= "default";
-				pinctrl-0	= <&card_detect>;
-				cd-gpios	= <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
-			};
-			/* WLAN */
-			sdcc4: mmc@121c0000 {
-				status = "okay";
-				vmmc-supply = <&ext_3p3v>;
-				vqmmc-supply = <&pm8921_lvs1>;
-				mmc-pwrseq = <&sdcc4_pwrseq>;
-			};
-		};
-
-		hdmi-tx@4a00000 {
-			status = "okay";
-
-			core-vdda-supply = <&pm8921_hdmi_switch>;
-			hdmi-mux-supply = <&ext_3p3v>;
-
-			hpd-gpios = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>;
-
-			ports {
-				port@0 {
-					endpoint {
-						remote-endpoint = <&mdp_dtv_out>;
-					};
-				};
-
-				port@1 {
-					endpoint {
-						remote-endpoint = <&hdmi_con>;
-					};
-				};
-			};
-		};
-
-		hdmi-phy@4a00400 {
-			status = "okay";
-
-			core-vdda-supply = <&pm8921_hdmi_switch>;
-		};
-
-		mdp@5100000 {
-			status = "okay";
-
-			ports {
-				port@3 {
-					endpoint {
-						remote-endpoint = <&hdmi_in>;
-					};
-				};
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-apq8064-pins.dtsi b/arch/arm/boot/dts/qcom-apq8064-pins.dtsi
deleted file mode 100644
index cbe42c4153a0..000000000000
--- a/arch/arm/boot/dts/qcom-apq8064-pins.dtsi
+++ /dev/null
@@ -1,325 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-
-&tlmm_pinmux {
-	sdc4_gpios: sdc4-gpios {
-		pios {
-			pins = "gpio63", "gpio64", "gpio65", "gpio66", "gpio67", "gpio68";
-			function = "sdc4";
-		};
-	};
-
-	sdcc1_pins: sdcc1-pin-active {
-		clk {
-			pins = "sdc1_clk";
-			drive-strengh = <16>;
-			bias-disable;
-		};
-
-		cmd {
-			pins = "sdc1_cmd";
-			drive-strengh = <10>;
-			bias-pull-up;
-		};
-
-		data {
-			pins = "sdc1_data";
-			drive-strengh = <10>;
-			bias-pull-up;
-		};
-	};
-
-	sdcc3_pins: sdcc3-pin-active {
-		clk {
-			pins = "sdc3_clk";
-			drive-strengh = <8>;
-			bias-disable;
-		};
-
-		cmd {
-			pins = "sdc3_cmd";
-			drive-strengh = <8>;
-			bias-pull-up;
-		};
-
-		data {
-			pins = "sdc3_data";
-			drive-strengh = <8>;
-			bias-pull-up;
-		};
-	};
-
-	ps_hold: ps_hold {
-		mux {
-			pins = "gpio78";
-			function = "ps_hold";
-		};
-	};
-
-	i2c1_pins: i2c1 {
-		mux {
-			pins = "gpio20", "gpio21";
-			function = "gsbi1";
-		};
-
-		pinconf {
-			pins = "gpio20", "gpio21";
-			drive-strength = <16>;
-			bias-disable;
-		};
-	};
-
-	i2c1_pins_sleep: i2c1_pins_sleep {
-		mux {
-			pins = "gpio20", "gpio21";
-			function = "gpio";
-		};
-		pinconf {
-			pins = "gpio20", "gpio21";
-			drive-strength = <2>;
-			bias-disable = <0>;
-		};
-	};
-
-	gsbi1_uart_2pins: gsbi1_uart_2pins {
-		mux {
-			pins = "gpio18", "gpio19";
-			function = "gsbi1";
-		};
-	};
-
-	gsbi1_uart_4pins: gsbi1_uart_4pins {
-		mux {
-			pins = "gpio18", "gpio19", "gpio20", "gpio21";
-			function = "gsbi1";
-		};
-	};
-
-	i2c2_pins: i2c2 {
-		mux {
-			pins = "gpio24", "gpio25";
-			function = "gsbi2";
-		};
-
-		pinconf {
-			pins = "gpio24", "gpio25";
-			drive-strength = <16>;
-			bias-disable;
-		};
-	};
-
-	i2c2_pins_sleep: i2c2_pins_sleep {
-		mux {
-			pins = "gpio24", "gpio25";
-			function = "gpio";
-		};
-
-		pinconf {
-			pins = "gpio24", "gpio25";
-			drive-strength = <2>;
-			bias-disable = <0>;
-		};
-	};
-
-	i2c3_pins: i2c3 {
-		mux {
-			pins = "gpio8", "gpio9";
-			function = "gsbi3";
-		};
-
-		pinconf {
-			pins = "gpio8", "gpio9";
-			drive-strength = <16>;
-			bias-disable;
-		};
-	};
-
-	i2c3_pins_sleep: i2c3_pins_sleep {
-		mux {
-			pins = "gpio8", "gpio9";
-			function = "gpio";
-		};
-		pinconf {
-			pins = "gpio8", "gpio9";
-			drive-strength = <2>;
-			bias-disable = <0>;
-		};
-	};
-
-	i2c4_pins: i2c4 {
-		mux {
-			pins = "gpio12", "gpio13";
-			function = "gsbi4";
-		};
-
-		pinconf {
-			pins = "gpio12", "gpio13";
-			drive-strength = <16>;
-			bias-disable;
-		};
-	};
-
-	i2c4_pins_sleep: i2c4_pins_sleep {
-		mux {
-			pins = "gpio12", "gpio13";
-			function = "gpio";
-		};
-		pinconf {
-			pins = "gpio12", "gpio13";
-			drive-strength = <2>;
-			bias-disable = <0>;
-		};
-	};
-
-	spi5_default: spi5_default {
-		pinmux {
-			pins = "gpio51", "gpio52", "gpio54";
-			function = "gsbi5";
-		};
-
-		pinmux_cs {
-			function = "gpio";
-			pins = "gpio53";
-		};
-
-		pinconf {
-			pins = "gpio51", "gpio52", "gpio54";
-			drive-strength = <16>;
-			bias-disable;
-		};
-
-		pinconf_cs {
-			pins = "gpio53";
-			drive-strength = <16>;
-			bias-disable;
-			output-high;
-		};
-	};
-
-	spi5_sleep: spi5_sleep {
-		pinmux {
-			function = "gpio";
-			pins = "gpio51", "gpio52", "gpio53", "gpio54";
-		};
-
-		pinconf {
-			pins = "gpio51", "gpio52", "gpio53", "gpio54";
-			drive-strength = <2>;
-			bias-pull-down;
-		};
-	};
-
-	i2c6_pins: i2c6 {
-		mux {
-			pins = "gpio16", "gpio17";
-			function = "gsbi6";
-		};
-
-		pinconf {
-			pins = "gpio16", "gpio17";
-			drive-strength = <16>;
-			bias-disable;
-		};
-	};
-
-	i2c6_pins_sleep: i2c6_pins_sleep {
-		mux {
-			pins = "gpio16", "gpio17";
-			function = "gpio";
-		};
-		pinconf {
-			pins = "gpio16", "gpio17";
-			drive-strength = <2>;
-			bias-disable = <0>;
-		};
-	};
-
-	gsbi6_uart_2pins: gsbi6_uart_2pins {
-		mux {
-			pins = "gpio14", "gpio15";
-			function = "gsbi6";
-		};
-	};
-
-	gsbi6_uart_4pins: gsbi6_uart_4pins {
-		mux {
-			pins = "gpio14", "gpio15", "gpio16", "gpio17";
-			function = "gsbi6";
-		};
-	};
-
-	gsbi7_uart_2pins: gsbi7_uart_2pins {
-		mux {
-			pins = "gpio82", "gpio83";
-			function = "gsbi7";
-		};
-	};
-
-	gsbi7_uart_4pins: gsbi7_uart_4pins {
-		mux {
-			pins = "gpio82", "gpio83", "gpio84", "gpio85";
-			function = "gsbi7";
-		};
-	};
-
-	i2c7_pins: i2c7 {
-		mux {
-			pins = "gpio84", "gpio85";
-			function = "gsbi7";
-		};
-
-		pinconf {
-			pins = "gpio84", "gpio85";
-			drive-strength = <16>;
-			bias-disable;
-		};
-	};
-
-	i2c7_pins_sleep: i2c7_pins_sleep {
-		mux {
-			pins = "gpio84", "gpio85";
-			function = "gpio";
-		};
-		pinconf {
-			pins = "gpio84", "gpio85";
-			drive-strength = <2>;
-			bias-disable = <0>;
-		};
-	};
-
-	riva_fm_pin_a: riva-fm-active {
-		pins = "gpio14", "gpio15";
-		function = "riva_fm";
-	};
-
-	riva_bt_pin_a: riva-bt-active {
-		pins = "gpio16", "gpio17";
-		function = "riva_bt";
-	};
-
-	riva_wlan_pin_a: riva-wlan-active {
-		pins = "gpio64", "gpio65", "gpio66", "gpio67", "gpio68";
-		function = "riva_wlan";
-
-		drive-strength = <6>;
-		bias-pull-down;
-	};
-
-	hdmi_pinctrl: hdmi-pinctrl {
-		mux {
-			pins = "gpio70", "gpio71", "gpio72";
-			function = "hdmi";
-		};
-
-		pinconf_ddc {
-			pins = "gpio70", "gpio71";
-			bias-pull-up;
-			drive-strength = <2>;
-		};
-
-		pinconf_hpd {
-			pins = "gpio72";
-			bias-pull-down;
-			drive-strength = <16>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts b/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts
deleted file mode 100644
index 0cee62c7b8b0..000000000000
--- a/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts
+++ /dev/null
@@ -1,401 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-apq8064-v2.0.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/mfd/qcom-rpm.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-
-/ {
-	model = "Sony Xperia Z";
-	compatible = "sony,xperia-yuga", "qcom,apq8064";
-
-	aliases {
-		serial0 = &gsbi5_serial;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&gpio_keys_pin_a>;
-
-		camera-focus {
-			label = "camera_focus";
-			gpios = <&pm8921_gpio 3 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_CAMERA_FOCUS>;
-		};
-
-		camera-snapshot {
-			label = "camera_snapshot";
-			gpios = <&pm8921_gpio 4 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_CAMERA>;
-		};
-
-		volume-down {
-			label = "volume_down";
-			gpios = <&pm8921_gpio 29 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEDOWN>;
-		};
-
-		volume-up {
-			label = "volume_up";
-			gpios = <&pm8921_gpio 35 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEUP>;
-		};
-	};
-
-	soc {
-		pinctrl@800000 {
-			gsbi5_uart_pin_a: gsbi5-uart-pin-active {
-				rx {
-					pins = "gpio52";
-					function = "gsbi5";
-					drive-strength = <2>;
-					bias-pull-up;
-				};
-
-				tx {
-					pins = "gpio51";
-					function = "gsbi5";
-					drive-strength = <4>;
-					bias-disable;
-				};
-			};
-
-
-			sdcc3_cd_pin_a: sdcc3-cd-pin-active {
-				pins = "gpio26";
-				function = "gpio";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-
-		rpm@108000 {
-			regulators {
-				vin_l1_l2_l12_l18-supply = <&pm8921_s4>;
-				vin_lvs_1_3_6-supply = <&pm8921_s4>;
-				vin_lvs_4_5_7-supply = <&pm8921_s4>;
-				vin_ncp-supply = <&pm8921_l6>;
-				vin_lvs2-supply = <&pm8921_s4>;
-				vin_l24-supply = <&pm8921_s1>;
-				vin_l25-supply = <&pm8921_s1>;
-				vin_l27-supply = <&pm8921_s7>;
-				vin_l28-supply = <&pm8921_s7>;
-
-				/* Buck SMPS */
-				s1 {
-					regulator-always-on;
-					regulator-min-microvolt = <1225000>;
-					regulator-max-microvolt = <1225000>;
-					qcom,switch-mode-frequency = <3200000>;
-					bias-pull-down;
-				};
-
-				s2 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				s3 {
-					regulator-min-microvolt = <500000>;
-					regulator-max-microvolt = <1150000>;
-					qcom,switch-mode-frequency = <4800000>;
-					bias-pull-down;
-				};
-
-				s4 {
-					regulator-always-on;
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-					qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
-				};
-
-				s7 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <3200000>;
-				};
-
-				s8 {
-					regulator-min-microvolt = <2200000>;
-					regulator-max-microvolt = <2200000>;
-					qcom,switch-mode-frequency = <1600000>;
-				};
-
-				/* PMOS LDO */
-				l1 {
-					regulator-always-on;
-					regulator-min-microvolt = <1100000>;
-					regulator-max-microvolt = <1100000>;
-					bias-pull-down;
-				};
-
-				l2 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-
-				l3 {
-					regulator-min-microvolt = <3075000>;
-					regulator-max-microvolt = <3075000>;
-					bias-pull-down;
-				};
-
-				l4 {
-					regulator-always-on;
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				l5 {
-					regulator-min-microvolt = <2950000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				l6 {
-					regulator-min-microvolt = <2950000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				l7 {
-					regulator-min-microvolt = <1850000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				l8 {
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-					bias-pull-down;
-				};
-
-				l9 {
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-				};
-
-				l10 {
-					regulator-min-microvolt = <2900000>;
-					regulator-max-microvolt = <2900000>;
-					bias-pull-down;
-				};
-
-				l11 {
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-				};
-
-				l12 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-
-				l14 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				l15 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				l16 {
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-					bias-pull-down;
-				};
-
-				l17 {
-					regulator-min-microvolt = <2000000>;
-					regulator-max-microvolt = <2000000>;
-					bias-pull-down;
-				};
-
-				l18 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-
-				l21 {
-					regulator-min-microvolt = <1050000>;
-					regulator-max-microvolt = <1050000>;
-					bias-pull-down;
-				};
-
-				l22 {
-					regulator-min-microvolt = <2600000>;
-					regulator-max-microvolt = <2600000>;
-					bias-pull-down;
-				};
-
-				l23 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				l24 {
-					regulator-min-microvolt = <750000>;
-					regulator-max-microvolt = <1150000>;
-					bias-pull-down;
-				};
-
-				l25 {
-					regulator-always-on;
-					regulator-min-microvolt = <1250000>;
-					regulator-max-microvolt = <1250000>;
-					bias-pull-down;
-				};
-
-				l27 {
-					regulator-min-microvolt = <1100000>;
-					regulator-max-microvolt = <1100000>;
-				};
-
-				l28 {
-					regulator-min-microvolt = <1050000>;
-					regulator-max-microvolt = <1050000>;
-					bias-pull-down;
-				};
-
-				l29 {
-					regulator-min-microvolt = <2000000>;
-					regulator-max-microvolt = <2000000>;
-					bias-pull-down;
-				};
-
-				/* Low Voltage Switch */
-				lvs1 {
-					bias-pull-down;
-				};
-
-				lvs2 {
-					bias-pull-down;
-				};
-
-				lvs3 {
-					bias-pull-down;
-				};
-
-				lvs4 {
-					bias-pull-down;
-				};
-
-				lvs5 {
-					bias-pull-down;
-				};
-
-				lvs6 {
-					bias-pull-down;
-				};
-
-				lvs7 {
-					bias-pull-down;
-				};
-
-				usb-switch {};
-
-				hdmi-switch {};
-
-				ncp {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					qcom,switch-mode-frequency = <1600000>;
-				};
-			};
-		};
-
-		qcom,ssbi@500000 {
-			pmic@0 {
-				gpio@150 {
-					gpio_keys_pin_a: gpio-keys-pin-active {
-						pins = "gpio3", "gpio4", "gpio29", "gpio35";
-						function = "normal";
-
-						bias-pull-up;
-						drive-push-pull;
-						input-enable;
-						power-source = <2>;
-						qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
-						qcom,pull-up-strength = <0>;
-					};
-				};
-			};
-		};
-
-		usb@12500000 {
-			status = "okay";
-			dr_mode = "otg";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l4>;
-				};
-			};
-		};
-
-		gsbi@1a200000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
-
-			serial@1a240000 {
-				status = "okay";
-
-				pinctrl-names = "default";
-				pinctrl-0 = <&gsbi5_uart_pin_a>;
-			};
-		};
-
-		amba {
-			sdcc1: mmc@12400000 {
-				status = "okay";
-
-				vmmc-supply = <&pm8921_l5>;
-				vqmmc-supply = <&pm8921_s4>;
-			};
-
-			sdcc3: mmc@12180000 {
-				status = "okay";
-
-				vmmc-supply = <&pm8921_l6>;
-				cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
-
-				pinctrl-names = "default";
-				pinctrl-0 = <&sdcc3_pins>, <&sdcc3_cd_pin_a>;
-			};
-		};
-
-		riva-pil@3204000 {
-			status = "okay";
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&riva_wlan_pin_a>, <&riva_bt_pin_a>, <&riva_fm_pin_a>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
deleted file mode 100644
index 83793b835d40..000000000000
--- a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
+++ /dev/null
@@ -1,346 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-msm8974.dtsi"
-#include "qcom-pm8841.dtsi"
-#include "qcom-pm8941.dtsi"
-
-/ {
-	model = "Qualcomm APQ8074 Dragonboard";
-	compatible = "qcom,apq8074-dragonboard", "qcom,apq8074";
-
-	aliases {
-		serial0 = &blsp1_uart2;
-		usid0 = &pm8941_0;
-		usid4 = &pm8841_0;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	soc {
-		serial@f991e000 {
-			status = "okay";
-		};
-
-		sdhci@f9824900 {
-			bus-width = <8>;
-			non-removable;
-			status = "okay";
-
-			vmmc-supply = <&pm8941_l20>;
-			vqmmc-supply = <&pm8941_s3>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&sdhc1_pin_a>;
-		};
-
-		sdhci@f98a4900 {
-			cd-gpios = <&msmgpio 62 0x1>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
-			bus-width = <4>;
-			status = "okay";
-
-			vmmc-supply = <&pm8941_l21>;
-			vqmmc-supply = <&pm8941_l13>;
-		};
-
-		usb@f9a55000 {
-			status = "okay";
-			phys = <&usb_hs2_phy>;
-			phy-select = <&tcsr 0xb000 1>;
-			extcon = <&smbb>, <&usb_id>;
-			vbus-supply = <&chg_otg>;
-			hnp-disable;
-			srp-disable;
-			adp-disable;
-			ulpi {
-				phy@b {
-					status = "okay";
-					v3p3-supply = <&pm8941_l24>;
-					v1p8-supply = <&pm8941_l6>;
-					extcon = <&smbb>;
-					qcom,init-seq = /bits/ 8 <0x1 0x63>;
-				};
-			};
-		};
-
-
-		pinctrl@fd510000 {
-			i2c11_pins: i2c11 {
-				mux {
-					pins = "gpio83", "gpio84";
-					function = "blsp_i2c11";
-				};
-			};
-
-			spi8_default: spi8_default {
-				mosi {
-					pins = "gpio45";
-					function = "blsp_spi8";
-				};
-				miso {
-					pins = "gpio46";
-					function = "blsp_spi8";
-				};
-				cs {
-					pins = "gpio47";
-					function = "blsp_spi8";
-				};
-				clk {
-					pins = "gpio48";
-					function = "blsp_spi8";
-				};
-			};
-
-			sdhc1_pin_a: sdhc1-pin-active {
-				clk {
-					pins = "sdc1_clk";
-					drive-strength = <16>;
-					bias-disable;
-				};
-
-				cmd-data {
-					pins = "sdc1_cmd", "sdc1_data";
-					drive-strength = <10>;
-					bias-pull-up;
-				};
-			};
-
-			sdhc2_cd_pin_a: sdhc2-cd-pin-active {
-				pins = "gpio62";
-				function = "gpio";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-
-			sdhc2_pin_a: sdhc2-pin-active {
-				clk {
-					pins = "sdc2_clk";
-					drive-strength = <10>;
-					bias-disable;
-				};
-
-				cmd-data {
-					pins = "sdc2_cmd", "sdc2_data";
-					drive-strength = <6>;
-					bias-pull-up;
-				};
-			};
-		};
-
-		i2c@f9967000 {
-			status = "okay";
-			clock-frequency = <200000>;
-			pinctrl-0 = <&i2c11_pins>;
-			pinctrl-names = "default";
-
-			eeprom: eeprom@52 {
-				compatible = "atmel,24c128";
-				reg = <0x52>;
-				pagesize = <32>;
-				read-only;
-			};
-		};
-	};
-
-	smd {
-		rpm {
-			rpm_requests {
-				pm8841-regulators {
-					s1 {
-						regulator-min-microvolt = <675000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s2 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s3 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s4 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-				};
-
-				pm8941-regulators {
-					vdd_l1_l3-supply = <&pm8941_s1>;
-					vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
-					vdd_l4_l11-supply = <&pm8941_s1>;
-					vdd_l5_l7-supply = <&pm8941_s2>;
-					vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
-					vin_5vs-supply = <&pm8941_5v>;
-
-					s1 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					s2 {
-						regulator-min-microvolt = <2150000>;
-						regulator-max-microvolt = <2150000>;
-						regulator-boot-on;
-					};
-
-					s3 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l1 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l2 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					l3 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					l4 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					l5 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l6 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l7 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l8 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l9 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					l10 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-						regulator-always-on;
-					};
-
-					l11 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-					};
-
-					l12 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l13 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l14 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l15 {
-						regulator-min-microvolt = <2050000>;
-						regulator-max-microvolt = <2050000>;
-					};
-
-					l16 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l17 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l18 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					l19 {
-						regulator-min-microvolt = <3300000>;
-						regulator-max-microvolt = <3300000>;
-						regulator-always-on;
-					};
-
-					l20 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-allow-set-load;
-						regulator-boot-on;
-						regulator-system-load = <200000>;
-					};
-
-					l21 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l22 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3000000>;
-					};
-
-					l23 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3000000>;
-					};
-
-					l24 {
-						regulator-min-microvolt = <3075000>;
-						regulator-max-microvolt = <3075000>;
-
-						regulator-boot-on;
-					};
-				};
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi b/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi
deleted file mode 100644
index 0c10d9e096db..000000000000
--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi
+++ /dev/null
@@ -1,112 +0,0 @@
-/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
- *
- * Permission to use, copy, modify, and/or distribute this software for any
- * purpose with or without fee is hereby granted, provided that the above
- * copyright notice and this permission notice appear in all copies.
- *
- * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
- * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
- * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
- * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
- * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
- * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
- *
- */
-
-#include "qcom-ipq4019.dtsi"
-
-/ {
-	model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK01.1";
-
-	aliases {
-		serial0 = &blsp1_uart1;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	soc {
-		rng@22000 {
-			status = "okay";
-		};
-
-		pinctrl@1000000 {
-			serial_pins: serial_pinmux {
-				mux {
-					pins = "gpio60", "gpio61";
-					function = "blsp_uart0";
-					bias-disable;
-				};
-			};
-
-			spi_0_pins: spi_0_pinmux {
-				pinmux {
-					function = "blsp_spi0";
-					pins = "gpio55", "gpio56", "gpio57";
-				};
-				pinmux_cs {
-					function = "gpio";
-					pins = "gpio54";
-				};
-				pinconf {
-					pins = "gpio55", "gpio56", "gpio57";
-					drive-strength = <12>;
-					bias-disable;
-				};
-				pinconf_cs {
-					pins = "gpio54";
-					drive-strength = <2>;
-					bias-disable;
-					output-high;
-				};
-			};
-		};
-
-		blsp_dma: dma@7884000 {
-			status = "okay";
-		};
-
-		spi@78b5000 {
-			pinctrl-0 = <&spi_0_pins>;
-			pinctrl-names = "default";
-			status = "okay";
-			cs-gpios = <&tlmm 54 0>;
-
-			mx25l25635e@0 {
-				#address-cells = <1>;
-				#size-cells = <1>;
-				reg = <0>;
-				compatible = "mx25l25635e";
-				spi-max-frequency = <24000000>;
-			};
-		};
-
-		serial@78af000 {
-			pinctrl-0 = <&serial_pins>;
-			pinctrl-names = "default";
-			status = "okay";
-		};
-
-		cryptobam: dma@8e04000 {
-			status = "okay";
-		};
-
-		crypto@8e3a000 {
-			status = "okay";
-		};
-
-		watchdog@b017000 {
-			status = "okay";
-		};
-
-		wifi@a000000 {
-			status = "okay";
-		};
-
-		wifi@a800000 {
-			status = "okay";
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi b/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi
deleted file mode 100644
index 65330065390a..000000000000
--- a/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi
+++ /dev/null
@@ -1,127 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-ipq8064.dtsi"
-#include <dt-bindings/input/input.h>
-
-/ {
-	model = "Qualcomm Technologies, Inc. IPQ8064-v1.0";
-
-	aliases {
-		serial0 = &gsbi4_serial;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	soc {
-		gsbi@16300000 {
-			qcom,mode = <GSBI_PROT_I2C_UART>;
-			status = "okay";
-
-			serial@16340000 {
-				status = "okay";
-			};
-		};
-
-		gsbi5: gsbi@1a200000 {
-			qcom,mode = <GSBI_PROT_SPI>;
-			status = "okay";
-
-			spi4: spi@1a280000 {
-				status = "okay";
-				spi-max-frequency = <50000000>;
-
-				pinctrl-0 = <&spi_pins>;
-				pinctrl-names = "default";
-
-				cs-gpios = <&qcom_pinmux 20 0>;
-
-				flash: m25p80@0 {
-					compatible = "s25fl256s1";
-					#address-cells = <1>;
-					#size-cells = <1>;
-					spi-max-frequency = <50000000>;
-					reg = <0>;
-
-					partition@0 {
-						label = "rootfs";
-						reg = <0x0 0x1000000>;
-					};
-
-					partition@1 {
-						label = "scratch";
-						reg = <0x1000000 0x1000000>;
-					};
-				};
-			};
-		};
-
-		sata-phy@1b400000 {
-			status = "okay";
-		};
-
-		sata@29000000 {
-			ports-implemented = <0x1>;
-			status = "okay";
-		};
-
-		gpio_keys {
-			compatible = "gpio-keys";
-			pinctrl-0 = <&buttons_pins>;
-			pinctrl-names = "default";
-
-			button@1 {
-				label = "reset";
-				linux,code = <KEY_RESTART>;
-				gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
-				linux,input-type = <1>;
-				debounce-interval = <60>;
-			};
-			button@2 {
-				label = "wps";
-				linux,code = <KEY_WPS_BUTTON>;
-				gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
-				linux,input-type = <1>;
-				debounce-interval = <60>;
-			};
-		};
-
-		leds {
-			compatible = "gpio-leds";
-			pinctrl-0 = <&leds_pins>;
-			pinctrl-names = "default";
-
-			led@7 {
-				label = "led_usb1";
-				gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
-				linux,default-trigger = "usbdev";
-				default-state = "off";
-			};
-
-			led@8 {
-				label = "led_usb3";
-				gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
-				linux,default-trigger = "usbdev";
-				default-state = "off";
-			};
-
-			led@9 {
-				label = "status_led_fail";
-				gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
-				default-state = "off";
-			};
-
-			led@26 {
-				label = "sata_led";
-				gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
-				default-state = "off";
-			};
-
-			led@53 {
-				label = "status_led_pass";
-				gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
-				default-state = "off";
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-mdm9615-wp8548.dtsi b/arch/arm/boot/dts/qcom-mdm9615-wp8548.dtsi
deleted file mode 100644
index 10ad929759ed..000000000000
--- a/arch/arm/boot/dts/qcom-mdm9615-wp8548.dtsi
+++ /dev/null
@@ -1,171 +0,0 @@
-/*
- * Device Tree Source for Sierra Wireless WP8548 Module
- *
- * Copyright (C) 2016 BayLibre, SAS.
- * Author : Neil Armstrong <narmstrong@baylibre.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#include "qcom-mdm9615.dtsi"
-
-/ {
-	model = "Sierra Wireless WP8548 Module";
-	compatible = "swir,wp8548", "qcom,mdm9615";
-
-	memory@48000000 {
-		device_type = "memory";
-		reg = <0x48000000 0x7F00000>;
-	};
-};
-
-&msmgpio {
-	pinctrl-0 = <&reset_out_pins>;
-	pinctrl-names = "default";
-
-	gsbi3_pins: gsbi3_pins {
-		mux {
-			pins = "gpio8", "gpio9", "gpio10", "gpio11";
-			function = "gsbi3";
-			drive-strength = <8>;
-			bias-disable;
-		};
-	};
-
-	gsbi4_pins: gsbi4_pins {
-		mux {
-			pins = "gpio12", "gpio13", "gpio14", "gpio15";
-			function = "gsbi4";
-			drive-strength = <8>;
-			bias-disable;
-		};
-	};
-
-	gsbi5_i2c_pins: gsbi5_i2c_pins {
-		pin16 {
-			pins = "gpio16";
-			function = "gsbi5_i2c";
-			drive-strength = <8>;
-			bias-disable;
-		};
-
-		pin17 {
-			pins = "gpio17";
-			function = "gsbi5_i2c";
-			drive-strength = <2>;
-			bias-disable;
-		};
-	};
-
-	gsbi5_uart_pins: gsbi5_uart_pins {
-		mux {
-			pins = "gpio18", "gpio19";
-			function = "gsbi5_uart";
-			drive-strength = <8>;
-			bias-disable;
-		};
-	};
-
-	reset_out_pins: reset_out_pins {
-		pins {
-			pins = "gpio66";
-			function = "gpio";
-			drive-strength = <2>;
-			bias-pull-up;
-			output-high;
-		};
-	};
-};
-
-&pmicgpio {
-	usb_vbus_5v_pins: usb_vbus_5v_pins {
-		pins = "gpio4";
-		function = "normal";
-		output-high;
-		bias-disable;
-		qcom,drive-strength = <1>;
-		power-source = <2>;
-	};
-};
-
-&gsbi3 {
-	status = "okay";
-	qcom,mode = <GSBI_PROT_SPI>;
-};
-
-&gsbi3_spi {
-	status = "okay";
-	pinctrl-0 = <&gsbi3_pins>;
-	pinctrl-names = "default";
-	assigned-clocks = <&gcc GSBI3_QUP_CLK>;
-	assigned-clock-rates = <24000000>;
-};
-
-&gsbi4 {
-	status = "okay";
-	qcom,mode = <GSBI_PROT_UART_W_FC>;
-};
-
-&gsbi4_serial {
-	status = "okay";
-	pinctrl-0 = <&gsbi4_pins>;
-	pinctrl-names = "default";
-};
-
-&gsbi5 {
-	status = "okay";
-	qcom,mode = <GSBI_PROT_I2C_UART>;
-};
-
-&gsbi5_i2c {
-	status = "okay";
-	clock-frequency = <200000>;
-	pinctrl-0 = <&gsbi5_i2c_pins>;
-	pinctrl-names = "default";
-};
-
-&gsbi5_serial {
-	status = "okay";
-	pinctrl-0 = <&gsbi5_uart_pins>;
-	pinctrl-names = "default";
-};
-
-&sdcc1 {
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/qcom-mdm9615.dtsi b/arch/arm/boot/dts/qcom-mdm9615.dtsi
deleted file mode 100644
index 4d4f37cebf21..000000000000
--- a/arch/arm/boot/dts/qcom-mdm9615.dtsi
+++ /dev/null
@@ -1,551 +0,0 @@
-/*
- * Device Tree Source for Qualcomm MDM9615 SoC
- *
- * Copyright (C) 2016 BayLibre, SAS.
- * Author : Neil Armstrong <narmstrong@baylibre.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/clock/qcom,gcc-mdm9615.h>
-#include <dt-bindings/reset/qcom,gcc-mdm9615.h>
-#include <dt-bindings/mfd/qcom-rpm.h>
-#include <dt-bindings/soc/qcom,gsbi.h>
-
-/ {
-	#address-cells = <1>;
-	#size-cells = <1>;
-	model = "Qualcomm MDM9615";
-	compatible = "qcom,mdm9615";
-	interrupt-parent = <&intc>;
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu0: cpu@0 {
-			compatible = "arm,cortex-a5";
-			device_type = "cpu";
-			next-level-cache = <&L2>;
-		};
-	};
-
-	cpu-pmu {
-		compatible = "arm,cortex-a5-pmu";
-		interrupts = <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_HIGH)>;
-	};
-
-	clocks {
-		cxo_board {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <19200000>;
-		};
-	};
-
-	regulators {
-		vsdcc_fixed: vsdcc-regulator {
-			compatible = "regulator-fixed";
-			regulator-name = "SDCC Power";
-			regulator-min-microvolt = <2700000>;
-			regulator-max-microvolt = <2700000>;
-			regulator-always-on;
-		};
-	};
-
-	soc: soc {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-		compatible = "simple-bus";
-
-		L2: cache-controller@2040000 {
-			compatible = "arm,pl310-cache";
-			reg = <0x02040000 0x1000>;
-			arm,data-latency = <2 2 0>;
-			cache-unified;
-			cache-level = <2>;
-		};
-
-		intc: interrupt-controller@2000000 {
-			compatible = "qcom,msm-qgic2";
-			interrupt-controller;
-			#interrupt-cells = <3>;
-			reg = <0x02000000 0x1000>,
-			      <0x02002000 0x1000>;
-		};
-
-		timer@200a000 {
-			compatible = "qcom,kpss-timer", "qcom,msm-timer";
-			interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_EDGE_RISING)>,
-				     <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_EDGE_RISING)>,
-				     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_EDGE_RISING)>;
-			reg = <0x0200a000 0x100>;
-			clock-frequency = <27000000>,
-					  <32768>;
-			cpu-offset = <0x80000>;
-		};
-
-		msmgpio: pinctrl@800000 {
-			compatible = "qcom,mdm9615-pinctrl";
-			gpio-controller;
-			gpio-ranges = <&msmgpio 0 0 88>;
-			#gpio-cells = <2>;
-			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-			reg = <0x800000 0x4000>;
-		};
-
-		gcc: clock-controller@900000 {
-			compatible = "qcom,gcc-mdm9615";
-			#clock-cells = <1>;
-			#power-domain-cells = <1>;
-			#reset-cells = <1>;
-			reg = <0x900000 0x4000>;
-		};
-
-		lcc: clock-controller@28000000 {
-			compatible = "qcom,lcc-mdm9615";
-			reg = <0x28000000 0x1000>;
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-		};
-
-		l2cc: clock-controller@2011000 {
-			compatible = "qcom,kpss-gcc", "syscon";
-			reg = <0x02011000 0x1000>;
-		};
-
-		rng@1a500000 {
-			compatible = "qcom,prng";
-			reg = <0x1a500000 0x200>;
-			clocks = <&gcc PRNG_CLK>;
-			clock-names = "core";
-			assigned-clocks = <&gcc PRNG_CLK>;
-			assigned-clock-rates = <32000000>;
-		};
-
-		gsbi2: gsbi@16100000 {
-			compatible = "qcom,gsbi-v1.0.0";
-			cell-index = <2>;
-			reg = <0x16100000 0x100>;
-			clocks = <&gcc GSBI2_H_CLK>;
-			clock-names = "iface";
-			status = "disabled";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-
-			gsbi2_i2c: i2c@16180000 {
-				compatible = "qcom,i2c-qup-v1.1.1";
-				#address-cells = <1>;
-				#size-cells = <0>;
-				reg = <0x16180000 0x1000>;
-				interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
-
-				clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>;
-				clock-names = "core", "iface";
-				status = "disabled";
-			};
-		};
-
-		gsbi3: gsbi@16200000 {
-			compatible = "qcom,gsbi-v1.0.0";
-			cell-index = <3>;
-			reg = <0x16200000 0x100>;
-			clocks = <&gcc GSBI3_H_CLK>;
-			clock-names = "iface";
-			status = "disabled";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-
-			gsbi3_spi: spi@16280000 {
-				compatible = "qcom,spi-qup-v1.1.1";
-				#address-cells = <1>;
-				#size-cells = <0>;
-				reg = <0x16280000 0x1000>;
-				interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
-				spi-max-frequency = <24000000>;
-
-				clocks = <&gcc GSBI3_QUP_CLK>, <&gcc GSBI3_H_CLK>;
-				clock-names = "core", "iface";
-				status = "disabled";
-			};
-		};
-
-		gsbi4: gsbi@16300000 {
-			compatible = "qcom,gsbi-v1.0.0";
-			cell-index = <4>;
-			reg = <0x16300000 0x100>;
-			clocks = <&gcc GSBI4_H_CLK>;
-			clock-names = "iface";
-			status = "disabled";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-
-			syscon-tcsr = <&tcsr>;
-
-			gsbi4_serial: serial@16340000 {
-				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
-				reg = <0x16340000 0x1000>,
-				      <0x16300000 0x1000>;
-				interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>;
-				clock-names = "core", "iface";
-				status = "disabled";
-			};
-		};
-
-		gsbi5: gsbi@16400000 {
-			compatible = "qcom,gsbi-v1.0.0";
-			cell-index = <5>;
-			reg = <0x16400000 0x100>;
-			clocks = <&gcc GSBI5_H_CLK>;
-			clock-names = "iface";
-			status = "disabled";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-
-			syscon-tcsr = <&tcsr>;
-
-			gsbi5_i2c: i2c@16480000 {
-				compatible = "qcom,i2c-qup-v1.1.1";
-				#address-cells = <1>;
-				#size-cells = <0>;
-				reg = <0x16480000 0x1000>;
-				interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
-
-				/* QUP clock is not initialized, set rate */
-				assigned-clocks = <&gcc GSBI5_QUP_CLK>;
-				assigned-clock-rates = <24000000>;
-
-				clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
-				clock-names = "core", "iface";
-				status = "disabled";
-			};
-
-			gsbi5_serial: serial@16440000 {
-				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
-				reg = <0x16440000 0x1000>,
-				      <0x16400000 0x1000>;
-				interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
-				clock-names = "core", "iface";
-				status = "disabled";
-			};
-		};
-
-		qcom,ssbi@500000 {
-			compatible = "qcom,ssbi";
-			reg = <0x500000 0x1000>;
-			qcom,controller-type = "pmic-arbiter";
-
-			pmicintc: pmic@0 {
-				compatible = "qcom,pm8018", "qcom,pm8921";
-				interrupts = <GIC_PPI 226 IRQ_TYPE_LEVEL_HIGH>;
-				#interrupt-cells = <2>;
-				interrupt-controller;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				pwrkey@1c {
-					compatible = "qcom,pm8018-pwrkey", "qcom,pm8921-pwrkey";
-					reg = <0x1c>;
-					interrupt-parent = <&pmicintc>;
-					interrupts = <50 IRQ_TYPE_EDGE_RISING>,
-						     <51 IRQ_TYPE_EDGE_RISING>;
-					debounce = <15625>;
-					pull-up;
-				};
-
-				pmicmpp: mpps@50 {
-					compatible = "qcom,pm8018-mpp", "qcom,ssbi-mpp";
-					interrupt-controller;
-					#interrupt-cells = <2>;
-					reg = <0x50>;
-					gpio-controller;
-					#gpio-cells = <2>;
-					gpio-ranges = <&pmicmpp 0 0 6>;
-				};
-
-				rtc@11d {
-					compatible = "qcom,pm8018-rtc", "qcom,pm8921-rtc";
-					interrupt-parent = <&pmicintc>;
-					interrupts = <39 IRQ_TYPE_EDGE_RISING>;
-					reg = <0x11d>;
-					allow-set-time;
-				};
-
-				pmicgpio: gpio@150 {
-					compatible = "qcom,pm8018-gpio", "qcom,ssbi-gpio";
-					interrupt-controller;
-					#interrupt-cells = <2>;
-					gpio-controller;
-					gpio-ranges = <&pmicgpio 0 0 6>;
-					#gpio-cells = <2>;
-				};
-			};
-		};
-
-		sdcc1bam: dma@12182000{
-			compatible = "qcom,bam-v1.3.0";
-			reg = <0x12182000 0x8000>;
-			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc SDC1_H_CLK>;
-			clock-names = "bam_clk";
-			#dma-cells = <1>;
-			qcom,ee = <0>;
-		};
-
-		sdcc2bam: dma@12142000{
-			compatible = "qcom,bam-v1.3.0";
-			reg = <0x12142000 0x8000>;
-			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc SDC2_H_CLK>;
-			clock-names = "bam_clk";
-			#dma-cells = <1>;
-			qcom,ee = <0>;
-		};
-
-		amba {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-			sdcc1: mmc@12180000 {
-				status = "disabled";
-				compatible = "arm,pl18x", "arm,primecell";
-				arm,primecell-periphid = <0x00051180>;
-				reg = <0x12180000 0x2000>;
-				interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
-				clock-names = "mclk", "apb_pclk";
-				bus-width = <8>;
-				max-frequency = <48000000>;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				vmmc-supply = <&vsdcc_fixed>;
-				dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
-				dma-names = "tx", "rx";
-				assigned-clocks = <&gcc SDC1_CLK>;
-				assigned-clock-rates = <400000>;
-			};
-
-			sdcc2: mmc@12140000 {
-				compatible = "arm,pl18x", "arm,primecell";
-				arm,primecell-periphid = <0x00051180>;
-				status = "disabled";
-				reg = <0x12140000 0x2000>;
-				interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks = <&gcc SDC2_CLK>, <&gcc SDC2_H_CLK>;
-				clock-names = "mclk", "apb_pclk";
-				bus-width = <4>;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				max-frequency = <48000000>;
-				no-1-8-v;
-				vmmc-supply = <&vsdcc_fixed>;
-				dmas = <&sdcc2bam 2>, <&sdcc2bam 1>;
-				dma-names = "tx", "rx";
-				assigned-clocks = <&gcc SDC2_CLK>;
-				assigned-clock-rates = <400000>;
-			};
-		};
-
-		tcsr: syscon@1a400000 {
-			compatible = "qcom,tcsr-mdm9615", "syscon";
-			reg = <0x1a400000 0x100>;
-		};
-
-		rpm: rpm@108000 {
-			compatible = "qcom,rpm-mdm9615";
-			reg = <0x108000 0x1000>;
-
-			qcom,ipc = <&l2cc 0x8 2>;
-
-			interrupts = <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
-				     <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
-				     <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
-			interrupt-names	= "ack", "err", "wakeup";
-
-			regulators {
-				compatible = "qcom,rpm-pm8018-regulators";
-
-				vin_lvs1-supply = <&pm8018_s3>;
-
-				vdd_l7-supply = <&pm8018_s4>;
-				vdd_l8-supply = <&pm8018_s3>;
-				vdd_l9_l10_l11_l12-supply = <&pm8018_s5>;
-
-				/* Buck SMPS */
-				pm8018_s1: s1 {
-					regulator-min-microvolt = <500000>;
-					regulator-max-microvolt = <1150000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				pm8018_s2: s2 {
-					regulator-min-microvolt = <1225000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				pm8018_s3: s3 {
-					regulator-always-on;
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				pm8018_s4: s4 {
-					regulator-min-microvolt = <2100000>;
-					regulator-max-microvolt = <2200000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				pm8018_s5: s5 {
-					regulator-always-on;
-					regulator-min-microvolt = <1350000>;
-					regulator-max-microvolt = <1350000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				/* PMOS LDO */
-				pm8018_l2: l2 {
-					regulator-always-on;
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				pm8018_l3: l3 {
-					regulator-always-on;
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				pm8018_l4: l4 {
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-					bias-pull-down;
-				};
-
-				pm8018_l5: l5 {
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <2850000>;
-					bias-pull-down;
-				};
-
-				pm8018_l6: l6 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <2850000>;
-					bias-pull-down;
-				};
-
-				pm8018_l7: l7 {
-					regulator-min-microvolt = <1850000>;
-					regulator-max-microvolt = <1900000>;
-					bias-pull-down;
-				};
-
-				pm8018_l8: l8 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-
-				pm8018_l9: l9 {
-					regulator-min-microvolt = <750000>;
-					regulator-max-microvolt = <1150000>;
-					bias-pull-down;
-				};
-
-				pm8018_l10: l10 {
-					regulator-min-microvolt = <1050000>;
-					regulator-max-microvolt = <1050000>;
-					bias-pull-down;
-				};
-
-				pm8018_l11: l11 {
-					regulator-min-microvolt = <1050000>;
-					regulator-max-microvolt = <1050000>;
-					bias-pull-down;
-				};
-
-				pm8018_l12: l12 {
-					regulator-min-microvolt = <1050000>;
-					regulator-max-microvolt = <1050000>;
-					bias-pull-down;
-				};
-
-				pm8018_l13: l13 {
-					regulator-min-microvolt = <1850000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				pm8018_l14: l14 {
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <2850000>;
-					bias-pull-down;
-				};
-
-				/* Low Voltage Switch */
-				pm8018_lvs1: lvs1 {
-					bias-pull-down;
-				};
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-msm8226.dtsi b/arch/arm/boot/dts/qcom-msm8226.dtsi
deleted file mode 100644
index 85e56992d2d0..000000000000
--- a/arch/arm/boot/dts/qcom-msm8226.dtsi
+++ /dev/null
@@ -1,519 +0,0 @@
-// SPDX-License-Identifier: BSD-3-Clause
-/*
- * Copyright (c) 2020, The Linux Foundation. All rights reserved.
- */
-
-/dts-v1/;
-
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/clock/qcom,gcc-msm8974.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/reset/qcom,gcc-msm8974.h>
-
-/ {
-	#address-cells = <1>;
-	#size-cells = <1>;
-	interrupt-parent = <&intc>;
-
-	chosen { };
-
-	memory@0 {
-		device_type = "memory";
-		reg = <0x0 0x0>;
-	};
-
-	clocks {
-		xo_board: xo_board {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <19200000>;
-		};
-
-		sleep_clk: sleep_clk {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
-		};
-	};
-
-	firmware {
-		scm {
-			compatible = "qcom,scm-msm8226", "qcom,scm";
-			clocks = <&gcc GCC_CE1_CLK>, <&gcc GCC_CE1_AXI_CLK>, <&gcc GCC_CE1_AHB_CLK>;
-			clock-names = "core", "bus", "iface";
-		};
-	};
-
-	tcsr_mutex: hwlock {
-		compatible = "qcom,tcsr-mutex";
-		syscon = <&tcsr_mutex_block 0 0x80>;
-
-		#hwlock-cells = <1>;
-	};
-
-	reserved-memory {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		smem_region: smem@3000000 {
-			reg = <0x3000000 0x100000>;
-			no-map;
-		};
-	};
-
-	smd {
-		compatible = "qcom,smd";
-
-		rpm {
-			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
-			qcom,ipc = <&apcs 8 0>;
-			qcom,smd-edge = <15>;
-
-			rpm_requests: rpm-requests {
-				compatible = "qcom,rpm-msm8226";
-				qcom,smd-channels = "rpm_requests";
-
-				rpmpd: power-controller {
-					compatible = "qcom,msm8226-rpmpd";
-					#power-domain-cells = <1>;
-					operating-points-v2 = <&rpmpd_opp_table>;
-
-					rpmpd_opp_table: opp-table {
-						compatible = "operating-points-v2";
-
-						rpmpd_opp_ret: opp1 {
-							opp-level = <1>;
-						};
-						rpmpd_opp_svs_krait: opp2 {
-							opp-level = <2>;
-						};
-						rpmpd_opp_svs_soc: opp3 {
-							opp-level = <3>;
-						};
-						rpmpd_opp_nom: opp4 {
-							opp-level = <4>;
-						};
-						rpmpd_opp_turbo: opp5 {
-							opp-level = <5>;
-						};
-						rpmpd_opp_super_turbo: opp6 {
-							opp-level = <6>;
-						};
-					};
-				};
-			};
-		};
-	};
-
-	smem {
-		compatible = "qcom,smem";
-
-		memory-region = <&smem_region>;
-		qcom,rpm-msg-ram = <&rpm_msg_ram>;
-
-		hwlocks = <&tcsr_mutex 3>;
-	};
-
-	soc: soc {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		intc: interrupt-controller@f9000000 {
-			compatible = "qcom,msm-qgic2";
-			reg = <0xf9000000 0x1000>,
-			      <0xf9002000 0x1000>;
-			interrupt-controller;
-			#interrupt-cells = <3>;
-		};
-
-		apcs: syscon@f9011000 {
-			compatible = "syscon";
-			reg = <0xf9011000 0x1000>;
-		};
-
-		sdhc_1: sdhci@f9824900 {
-			compatible = "qcom,msm8226-sdhci", "qcom,sdhci-msm-v4";
-			reg = <0xf9824900 0x11c>, <0xf9824000 0x800>;
-			reg-names = "hc_mem", "core_mem";
-			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "hc_irq", "pwr_irq";
-			clocks = <&gcc GCC_SDCC1_APPS_CLK>,
-				 <&gcc GCC_SDCC1_AHB_CLK>,
-				 <&xo_board>;
-			clock-names = "core", "iface", "xo";
-			pinctrl-names = "default";
-			pinctrl-0 = <&sdhc1_default_state>;
-			status = "disabled";
-		};
-
-		sdhc_2: sdhci@f98a4900 {
-			compatible = "qcom,msm8226-sdhci", "qcom,sdhci-msm-v4";
-			reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>;
-			reg-names = "hc_mem", "core_mem";
-			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "hc_irq", "pwr_irq";
-			clocks = <&gcc GCC_SDCC2_APPS_CLK>,
-				 <&gcc GCC_SDCC2_AHB_CLK>,
-				 <&xo_board>;
-			clock-names = "core", "iface", "xo";
-			pinctrl-names = "default";
-			pinctrl-0 = <&sdhc2_default_state>;
-			status = "disabled";
-		};
-
-		sdhc_3: sdhci@f9864900 {
-			compatible = "qcom,msm8226-sdhci", "qcom,sdhci-msm-v4";
-			reg = <0xf9864900 0x11c>, <0xf9864000 0x800>;
-			reg-names = "hc_mem", "core_mem";
-			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "hc_irq", "pwr_irq";
-			clocks = <&gcc GCC_SDCC3_APPS_CLK>,
-				 <&gcc GCC_SDCC3_AHB_CLK>,
-				 <&xo_board>;
-			clock-names = "core", "iface", "xo";
-			pinctrl-names = "default";
-			pinctrl-0 = <&sdhc3_default_state>;
-			status = "disabled";
-		};
-
-		blsp1_uart3: serial@f991f000 {
-			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
-			reg = <0xf991f000 0x1000>;
-			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
-			clock-names = "core", "iface";
-			status = "disabled";
-		};
-
-		blsp1_uart4: serial@f9920000 {
-			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
-			reg = <0xf9920000 0x1000>;
-			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_UART4_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
-			clock-names = "core", "iface";
-			status = "disabled";
-		};
-
-		blsp1_i2c1: i2c@f9923000 {
-			status = "disabled";
-			compatible = "qcom,i2c-qup-v2.1.1";
-			reg = <0xf9923000 0x1000>;
-			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
-			clock-names = "core", "iface";
-			pinctrl-names = "default";
-			pinctrl-0 = <&blsp1_i2c1_pins>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		blsp1_i2c2: i2c@f9924000 {
-			status = "disabled";
-			compatible = "qcom,i2c-qup-v2.1.1";
-			reg = <0xf9924000 0x1000>;
-			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
-			clock-names = "core", "iface";
-			pinctrl-names = "default";
-			pinctrl-0 = <&blsp1_i2c2_pins>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		blsp1_i2c3: i2c@f9925000 {
-			status = "disabled";
-			compatible = "qcom,i2c-qup-v2.1.1";
-			reg = <0xf9925000 0x1000>;
-			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
-			clock-names = "core", "iface";
-			pinctrl-names = "default";
-			pinctrl-0 = <&blsp1_i2c3_pins>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		blsp1_i2c4: i2c@f9926000 {
-			status = "disabled";
-			compatible = "qcom,i2c-qup-v2.1.1";
-			reg = <0xf9926000 0x1000>;
-			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
-			clock-names = "core", "iface";
-			pinctrl-names = "default";
-			pinctrl-0 = <&blsp1_i2c4_pins>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		blsp1_i2c5: i2c@f9927000 {
-			status = "disabled";
-			compatible = "qcom,i2c-qup-v2.1.1";
-			reg = <0xf9927000 0x1000>;
-			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
-			clock-names = "core", "iface";
-			pinctrl-names = "default";
-			pinctrl-0 = <&blsp1_i2c5_pins>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		usb: usb@f9a55000 {
-			compatible = "qcom,ci-hdrc";
-			reg = <0xf9a55000 0x200>,
-			      <0xf9a55200 0x200>;
-			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_USB_HS_AHB_CLK>,
-				 <&gcc GCC_USB_HS_SYSTEM_CLK>;
-			clock-names = "iface", "core";
-			assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>;
-			assigned-clock-rates = <75000000>;
-			resets = <&gcc GCC_USB_HS_BCR>;
-			reset-names = "core";
-			phy_type = "ulpi";
-			dr_mode = "otg";
-			hnp-disable;
-			srp-disable;
-			adp-disable;
-			ahb-burst-config = <0>;
-			phy-names = "usb-phy";
-			phys = <&usb_hs_phy>;
-			status = "disabled";
-			#reset-cells = <1>;
-
-			ulpi {
-				usb_hs_phy: phy {
-					compatible = "qcom,usb-hs-phy-msm8226",
-						     "qcom,usb-hs-phy";
-					#phy-cells = <0>;
-					clocks = <&xo_board>, <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
-					clock-names = "ref", "sleep";
-					resets = <&gcc GCC_USB2A_PHY_BCR>, <&usb 0>;
-					reset-names = "phy", "por";
-					qcom,init-seq = /bits/ 8 <0x0 0x44
-						0x1 0x68 0x2 0x24 0x3 0x13>;
-				};
-			};
-		};
-
-		gcc: clock-controller@fc400000 {
-			compatible = "qcom,gcc-msm8226";
-			reg = <0xfc400000 0x4000>;
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-			#power-domain-cells = <1>;
-		};
-
-		tlmm: pinctrl@fd510000 {
-			compatible = "qcom,msm8226-pinctrl";
-			reg = <0xfd510000 0x4000>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			gpio-ranges = <&tlmm 0 0 117>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
-
-			blsp1_i2c1_pins: blsp1-i2c1 {
-				pins = "gpio2", "gpio3";
-				function = "blsp_i2c1";
-				drive-strength = <2>;
-				bias-disable;
-			};
-
-			blsp1_i2c2_pins: blsp1-i2c2 {
-				pins = "gpio6", "gpio7";
-				function = "blsp_i2c2";
-				drive-strength = <2>;
-				bias-disable;
-			};
-
-			blsp1_i2c3_pins: blsp1-i2c3 {
-				pins = "gpio10", "gpio11";
-				function = "blsp_i2c3";
-				drive-strength = <2>;
-				bias-disable;
-			};
-
-			blsp1_i2c4_pins: blsp1-i2c4 {
-				pins = "gpio14", "gpio15";
-				function = "blsp_i2c4";
-				drive-strength = <2>;
-				bias-disable;
-			};
-
-			blsp1_i2c5_pins: blsp1-i2c5 {
-				pins = "gpio18", "gpio19";
-				function = "blsp_i2c5";
-				drive-strength = <2>;
-				bias-disable;
-			};
-
-			sdhc1_default_state: sdhc1-default-state {
-				clk {
-					pins = "sdc1_clk";
-					drive-strength = <10>;
-					bias-disable;
-				};
-
-				cmd-data {
-					pins = "sdc1_cmd", "sdc1_data";
-					drive-strength = <10>;
-					bias-pull-up;
-				};
-			};
-
-			sdhc2_default_state: sdhc2-default-state {
-				clk {
-					pins = "sdc2_clk";
-					drive-strength = <10>;
-					bias-disable;
-				};
-
-				cmd-data {
-					pins = "sdc2_cmd", "sdc2_data";
-					drive-strength = <10>;
-					bias-pull-up;
-				};
-			};
-
-			sdhc3_default_state: sdhc3-default-state {
-				clk {
-					pins = "gpio44";
-					function = "sdc3";
-					drive-strength = <8>;
-					bias-disable;
-				};
-
-				cmd {
-					pins = "gpio43";
-					function = "sdc3";
-					drive-strength = <8>;
-					bias-pull-up;
-				};
-
-				data {
-					pins = "gpio39", "gpio40", "gpio41", "gpio42";
-					function = "sdc3";
-					drive-strength = <8>;
-					bias-pull-up;
-				};
-			};
-		};
-
-		restart@fc4ab000 {
-			compatible = "qcom,pshold";
-			reg = <0xfc4ab000 0x4>;
-		};
-
-		spmi_bus: spmi@fc4cf000 {
-			compatible = "qcom,spmi-pmic-arb";
-			reg-names = "core", "intr", "cnfg";
-			reg = <0xfc4cf000 0x1000>,
-			      <0xfc4cb000 0x1000>,
-			      <0xfc4ca000 0x1000>;
-			interrupt-names = "periph_irq";
-			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
-			qcom,ee = <0>;
-			qcom,channel = <0>;
-			#address-cells = <2>;
-			#size-cells = <0>;
-			interrupt-controller;
-			#interrupt-cells = <4>;
-		};
-
-		rng@f9bff000 {
-			compatible = "qcom,prng";
-			reg = <0xf9bff000 0x200>;
-			clocks = <&gcc GCC_PRNG_AHB_CLK>;
-			clock-names = "core";
-		};
-
-		timer@f9020000 {
-			compatible = "arm,armv7-timer-mem";
-			reg = <0xf9020000 0x1000>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-
-			frame@f9021000 {
-				frame-number = <0>;
-				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
-					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xf9021000 0x1000>,
-				      <0xf9022000 0x1000>;
-			};
-
-			frame@f9023000 {
-				frame-number = <1>;
-				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xf9023000 0x1000>;
-				status = "disabled";
-			};
-
-			frame@f9024000 {
-				frame-number = <2>;
-				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xf9024000 0x1000>;
-				status = "disabled";
-			};
-
-			frame@f9025000 {
-				frame-number = <3>;
-				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xf9025000 0x1000>;
-				status = "disabled";
-			};
-
-			frame@f9026000 {
-				frame-number = <4>;
-				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xf9026000 0x1000>;
-				status = "disabled";
-			};
-
-			frame@f9027000 {
-				frame-number = <5>;
-				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xf9027000 0x1000>;
-				status = "disabled";
-			};
-
-			frame@f9028000 {
-				frame-number = <6>;
-				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0xf9028000 0x1000>;
-				status = "disabled";
-			};
-		};
-
-		rpm_msg_ram: memory@fc428000 {
-			compatible = "qcom,rpm-msg-ram";
-			reg = <0xfc428000 0x4000>;
-		};
-
-		tcsr_mutex_block: syscon@fd484000 {
-			compatible = "syscon";
-			reg = <0xfd484000 0x2000>;
-		};
-	};
-
-	timer {
-		compatible = "arm,armv7-timer";
-		interrupts = <GIC_PPI 2
-				(GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>,
-			     <GIC_PPI 3
-				(GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>,
-			     <GIC_PPI 4
-				(GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>,
-			     <GIC_PPI 1
-				(GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>;
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-msm8660-surf.dts b/arch/arm/boot/dts/qcom-msm8660-surf.dts
deleted file mode 100644
index 414280d9bdba..000000000000
--- a/arch/arm/boot/dts/qcom-msm8660-surf.dts
+++ /dev/null
@@ -1,78 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include <dt-bindings/input/input.h>
-
-#include "qcom-msm8660.dtsi"
-
-/ {
-	model = "Qualcomm MSM8660 SURF";
-	compatible = "qcom,msm8660-surf", "qcom,msm8660";
-
-	aliases {
-		serial0 = &gsbi12_serial;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	soc {
-		gsbi@19c00000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
-			serial@19c40000 {
-				status = "okay";
-			};
-		};
-
-		/* Temporary fixed regulator */
-		vsdcc_fixed: vsdcc-regulator {
-			compatible = "regulator-fixed";
-			regulator-name = "SDCC Power";
-			regulator-min-microvolt = <2700000>;
-			regulator-max-microvolt = <2700000>;
-			regulator-always-on;
-		};
-
-		amba {
-			/* eMMC */
-			sdcc1: mmc@12400000 {
-				status = "okay";
-				vmmc-supply = <&vsdcc_fixed>;
-			};
-
-			/* External micro SD card */
-			sdcc3: mmc@12180000 {
-				status = "okay";
-				vmmc-supply = <&vsdcc_fixed>;
-			};
-		};
-	};
-};
-
-&pm8058 {
-	keypad@148 {
-		linux,keymap = <
-			MATRIX_KEY(0, 0, KEY_FN_F1)
-			MATRIX_KEY(0, 1, KEY_UP)
-			MATRIX_KEY(0, 2, KEY_LEFT)
-			MATRIX_KEY(0, 3, KEY_VOLUMEUP)
-			MATRIX_KEY(1, 0, KEY_FN_F2)
-			MATRIX_KEY(1, 1, KEY_RIGHT)
-			MATRIX_KEY(1, 2, KEY_DOWN)
-			MATRIX_KEY(1, 3, KEY_VOLUMEDOWN)
-			MATRIX_KEY(2, 3, KEY_ENTER)
-			MATRIX_KEY(4, 0, KEY_CAMERA_FOCUS)
-			MATRIX_KEY(4, 1, KEY_UP)
-			MATRIX_KEY(4, 2, KEY_LEFT)
-			MATRIX_KEY(4, 3, KEY_HOME)
-			MATRIX_KEY(4, 4, KEY_FN_F3)
-			MATRIX_KEY(5, 0, KEY_CAMERA)
-			MATRIX_KEY(5, 1, KEY_RIGHT)
-			MATRIX_KEY(5, 2, KEY_DOWN)
-			MATRIX_KEY(5, 3, KEY_BACK)
-			MATRIX_KEY(5, 4, KEY_MENU)
-			>;
-		keypad,num-rows = <6>;
-		keypad,num-columns = <5>;
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-msm8960-cdp.dts b/arch/arm/boot/dts/qcom-msm8960-cdp.dts
deleted file mode 100644
index d1fd0fe12ffe..000000000000
--- a/arch/arm/boot/dts/qcom-msm8960-cdp.dts
+++ /dev/null
@@ -1,354 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include <dt-bindings/input/input.h>
-
-#include "qcom-msm8960.dtsi"
-
-/ {
-	model = "Qualcomm MSM8960 CDP";
-	compatible = "qcom,msm8960-cdp", "qcom,msm8960";
-
-	aliases {
-		serial0 = &gsbi5_serial;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	soc {
-		gsbi@16400000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
-			serial@16440000 {
-				status = "okay";
-			};
-		};
-
-		amba {
-			/* eMMC */
-			sdcc1: mmc@12400000 {
-				status = "okay";
-			};
-
-			/* External micro SD card */
-			sdcc3: mmc@12180000 {
-				status = "okay";
-			};
-		};
-
-		rpm@108000 {
-			regulators {
-				compatible = "qcom,rpm-pm8921-regulators";
-				vin_lvs1_3_6-supply = <&pm8921_s4>;
-				vin_lvs2-supply = <&pm8921_s4>;
-				vin_lvs4_5_7-supply = <&pm8921_s4>;
-				vdd_ncp-supply = <&pm8921_l6>;
-				vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
-				vdd_l21_l23_l29-supply = <&pm8921_s8>;
-				vdd_l24-supply = <&pm8921_s1>;
-				vdd_l25-supply = <&pm8921_s1>;
-				vdd_l27-supply = <&pm8921_s7>;
-				vdd_l28-supply = <&pm8921_s7>;
-
-				/* Buck SMPS */
-				pm8921_s1: s1 {
-					regulator-always-on;
-					regulator-min-microvolt = <1225000>;
-					regulator-max-microvolt = <1225000>;
-					qcom,switch-mode-frequency = <3200000>;
-					bias-pull-down;
-				};
-
-				pm8921_s2: s2 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				pm8921_s3: s3 {
-					regulator-min-microvolt = <500000>;
-					regulator-max-microvolt = <1150000>;
-					qcom,switch-mode-frequency = <4800000>;
-					bias-pull-down;
-				};
-
-				pm8921_s4: s4 {
-					regulator-always-on;
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-					qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
-				};
-
-				pm8921_s7: s7 {
-					regulator-min-microvolt = <1150000>;
-					regulator-max-microvolt = <1150000>;
-					qcom,switch-mode-frequency = <3200000>;
-					bias-pull-down;
-				};
-
-				pm8921_s8: s8 {
-					regulator-always-on;
-					regulator-min-microvolt = <2050000>;
-					regulator-max-microvolt = <2050000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				/* PMOS LDO */
-				pm8921_l1: l1 {
-					regulator-always-on;
-					regulator-min-microvolt = <1050000>;
-					regulator-max-microvolt = <1050000>;
-					bias-pull-down;
-				};
-
-				pm8921_l2: l2 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-
-				pm8921_l3: l3 {
-					regulator-min-microvolt = <3075000>;
-					regulator-max-microvolt = <3075000>;
-					bias-pull-down;
-				};
-
-				pm8921_l4: l4 {
-					regulator-always-on;
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				pm8921_l5: l5 {
-					regulator-min-microvolt = <2950000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				pm8921_l6: l6 {
-					regulator-min-microvolt = <2950000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				pm8921_l7: l7 {
-					regulator-always-on;
-					regulator-min-microvolt = <1850000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				pm8921_l8: l8 {
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-				};
-
-				pm8921_l9: l9 {
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-				};
-
-				pm8921_l10: l10 {
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-				};
-
-				pm8921_l11: l11 {
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <2850000>;
-					bias-pull-down;
-				};
-
-				pm8921_l12: l12 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-
-				pm8921_l14: l14 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				pm8921_l15: l15 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				pm8921_l16: l16 {
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-					bias-pull-down;
-				};
-
-				pm8921_l17: l17 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				pm8921_l18: l18 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					bias-pull-down;
-				};
-
-				pm8921_l21: l21 {
-					regulator-min-microvolt = <1900000>;
-					regulator-max-microvolt = <1900000>;
-					bias-pull-down;
-				};
-
-				pm8921_l22: l22 {
-					regulator-min-microvolt = <2750000>;
-					regulator-max-microvolt = <2750000>;
-					bias-pull-down;
-				};
-
-				pm8921_l23: l23 {
-					regulator-always-on;
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				pm8921_l24: l24 {
-					regulator-min-microvolt = <750000>;
-					regulator-max-microvolt = <1150000>;
-					bias-pull-down;
-				};
-
-				pm8921_l25: l25 {
-					regulator-always-on;
-					regulator-min-microvolt = <1250000>;
-					regulator-max-microvolt = <1250000>;
-					bias-pull-down;
-				};
-
-				/* Low Voltage Switch */
-				pm8921_lvs1: lvs1 {
-					bias-pull-down;
-				};
-
-				pm8921_lvs2: lvs2 {
-					bias-pull-down;
-				};
-
-				pm8921_lvs3: lvs3 {
-					bias-pull-down;
-				};
-
-				pm8921_lvs4: lvs4 {
-					bias-pull-down;
-				};
-
-				pm8921_lvs5: lvs5 {
-					bias-pull-down;
-				};
-
-				pm8921_lvs6: lvs6 {
-					bias-pull-down;
-				};
-
-				pm8921_lvs7: lvs7 {
-					bias-pull-down;
-				};
-
-				pm8921_ncp: ncp {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					qcom,switch-mode-frequency = <1600000>;
-				};
-			};
-		};
-
-		gsbi@16000000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_SPI>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&spi1_default>;
-			spi@16080000 {
-				status = "okay";
-				ethernet@0 {
-					compatible = "micrel,ks8851";
-					reg = <0>;
-					interrupt-parent = <&msmgpio>;
-					interrupts = <90 8>;
-					spi-max-frequency = <5400000>;
-					vdd-supply = <&ext_l2>;
-					vdd-io-supply = <&pm8921_lvs6>;
-					reset-gpios = <&msmgpio 89 0>;
-				};
-			};
-		};
-
-		pinctrl@800000 {
-			spi1_default: spi1_default {
-				mux {
-					pins = "gpio6", "gpio7", "gpio9";
-					function = "gsbi1";
-				};
-
-				mosi {
-					pins = "gpio6";
-					drive-strength = <12>;
-					bias-disable;
-				};
-
-				miso {
-					pins = "gpio7";
-					drive-strength = <12>;
-					bias-disable;
-				};
-
-				cs {
-					pins = "gpio8";
-					drive-strength = <12>;
-					bias-disable;
-					output-low;
-				};
-
-				clk {
-					pins = "gpio9";
-					drive-strength = <12>;
-					bias-disable;
-				};
-			};
-		};
-	};
-
-	regulators {
-		compatible = "simple-bus";
-
-		ext_l2: gpio-regulator@91 {
-			compatible = "regulator-fixed";
-			regulator-name = "ext_l2";
-			gpio = <&msmgpio 91 0>;
-			startup-delay-us = <10000>;
-			enable-active-high;
-		};
-	};
-};
-
-&pmicintc {
-	keypad@148 {
-		linux,keymap = <
-			MATRIX_KEY(0, 0, KEY_VOLUMEUP)
-			MATRIX_KEY(0, 1, KEY_VOLUMEDOWN)
-			MATRIX_KEY(0, 2, KEY_CAMERA_FOCUS)
-			MATRIX_KEY(0, 3, KEY_CAMERA)
-			>;
-		keypad,num-rows = <1>;
-		keypad,num-columns = <5>;
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom-msm8960.dtsi
deleted file mode 100644
index 4a2d74cf01d2..000000000000
--- a/arch/arm/boot/dts/qcom-msm8960.dtsi
+++ /dev/null
@@ -1,335 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/dts-v1/;
-
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/clock/qcom,gcc-msm8960.h>
-#include <dt-bindings/mfd/qcom-rpm.h>
-#include <dt-bindings/soc/qcom,gsbi.h>
-
-/ {
-	#address-cells = <1>;
-	#size-cells = <1>;
-	model = "Qualcomm MSM8960";
-	compatible = "qcom,msm8960";
-	interrupt-parent = <&intc>;
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		interrupts = <1 14 0x304>;
-
-		cpu@0 {
-			compatible = "qcom,krait";
-			enable-method = "qcom,kpss-acc-v1";
-			device_type = "cpu";
-			reg = <0>;
-			next-level-cache = <&L2>;
-			qcom,acc = <&acc0>;
-			qcom,saw = <&saw0>;
-		};
-
-		cpu@1 {
-			compatible = "qcom,krait";
-			enable-method = "qcom,kpss-acc-v1";
-			device_type = "cpu";
-			reg = <1>;
-			next-level-cache = <&L2>;
-			qcom,acc = <&acc1>;
-			qcom,saw = <&saw1>;
-		};
-
-		L2: l2-cache {
-			compatible = "cache";
-			cache-level = <2>;
-		};
-	};
-
-	memory {
-		device_type = "memory";
-		reg = <0x0 0x0>;
-	};
-
-	cpu-pmu {
-		compatible = "qcom,krait-pmu";
-		interrupts = <1 10 0x304>;
-		qcom,no-pc-write;
-	};
-
-	clocks {
-		cxo_board {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <19200000>;
-			clock-output-names = "cxo_board";
-		};
-
-		pxo_board {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <27000000>;
-			clock-output-names = "pxo_board";
-		};
-
-		sleep_clk {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
-			clock-output-names = "sleep_clk";
-		};
-	};
-
-	/* Temporary fixed regulator */
-	vsdcc_fixed: vsdcc-regulator {
-		compatible = "regulator-fixed";
-		regulator-name = "SDCC Power";
-		regulator-min-microvolt = <2700000>;
-		regulator-max-microvolt = <2700000>;
-		regulator-always-on;
-	};
-
-	soc: soc {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-		compatible = "simple-bus";
-
-		intc: interrupt-controller@2000000 {
-			compatible = "qcom,msm-qgic2";
-			interrupt-controller;
-			#interrupt-cells = <3>;
-			reg = <0x02000000 0x1000>,
-			      <0x02002000 0x1000>;
-		};
-
-		timer@200a000 {
-			compatible = "qcom,kpss-timer",
-				     "qcom,kpss-wdt-msm8960", "qcom,msm-timer";
-			interrupts = <1 1 0x301>,
-				     <1 2 0x301>,
-				     <1 3 0x301>;
-			reg = <0x0200a000 0x100>;
-			clock-frequency = <27000000>,
-					  <32768>;
-			cpu-offset = <0x80000>;
-		};
-
-		msmgpio: pinctrl@800000 {
-			compatible = "qcom,msm8960-pinctrl";
-			gpio-controller;
-			gpio-ranges = <&msmgpio 0 0 152>;
-			#gpio-cells = <2>;
-			interrupts = <0 16 0x4>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-			reg = <0x800000 0x4000>;
-		};
-
-		gcc: clock-controller@900000 {
-			compatible = "qcom,gcc-msm8960";
-			#clock-cells = <1>;
-			#power-domain-cells = <1>;
-			#reset-cells = <1>;
-			reg = <0x900000 0x4000>;
-		};
-
-		lcc: clock-controller@28000000 {
-			compatible = "qcom,lcc-msm8960";
-			reg = <0x28000000 0x1000>;
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-		};
-
-		clock-controller@4000000 {
-			compatible = "qcom,mmcc-msm8960";
-			reg = <0x4000000 0x1000>;
-			#clock-cells = <1>;
-			#power-domain-cells = <1>;
-			#reset-cells = <1>;
-		};
-
-		l2cc: clock-controller@2011000 {
-			compatible	= "qcom,kpss-gcc", "syscon";
-			reg		= <0x2011000 0x1000>;
-		};
-
-		rpm@108000 {
-			compatible	= "qcom,rpm-msm8960";
-			reg		= <0x108000 0x1000>;
-			qcom,ipc	= <&l2cc 0x8 2>;
-
-			interrupts	= <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
-					  <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
-					  <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
-			interrupt-names	= "ack", "err", "wakeup";
-
-			regulators {
-				compatible = "qcom,rpm-pm8921-regulators";
-			};
-		};
-
-		acc0: clock-controller@2088000 {
-			compatible = "qcom,kpss-acc-v1";
-			reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
-		};
-
-		acc1: clock-controller@2098000 {
-			compatible = "qcom,kpss-acc-v1";
-			reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
-		};
-
-		saw0: regulator@2089000 {
-			compatible = "qcom,saw2";
-			reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
-			regulator;
-		};
-
-		saw1: regulator@2099000 {
-			compatible = "qcom,saw2";
-			reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
-			regulator;
-		};
-
-		gsbi5: gsbi@16400000 {
-			compatible = "qcom,gsbi-v1.0.0";
-			cell-index = <5>;
-			reg = <0x16400000 0x100>;
-			clocks = <&gcc GSBI5_H_CLK>;
-			clock-names = "iface";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-
-			syscon-tcsr = <&tcsr>;
-
-			gsbi5_serial: serial@16440000 {
-				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
-				reg = <0x16440000 0x1000>,
-				      <0x16400000 0x1000>;
-				interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
-				clock-names = "core", "iface";
-				status = "disabled";
-			};
-		};
-
-		qcom,ssbi@500000 {
-			compatible = "qcom,ssbi";
-			reg = <0x500000 0x1000>;
-			qcom,controller-type = "pmic-arbiter";
-
-			pmicintc: pmic@0 {
-				compatible = "qcom,pm8921";
-				interrupt-parent = <&msmgpio>;
-				interrupts = <104 8>;
-				#interrupt-cells = <2>;
-				interrupt-controller;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				pwrkey@1c {
-					compatible = "qcom,pm8921-pwrkey";
-					reg = <0x1c>;
-					interrupt-parent = <&pmicintc>;
-					interrupts = <50 1>, <51 1>;
-					debounce = <15625>;
-					pull-up;
-				};
-
-				keypad@148 {
-					compatible = "qcom,pm8921-keypad";
-					reg = <0x148>;
-					interrupt-parent = <&pmicintc>;
-					interrupts = <74 1>, <75 1>;
-					debounce = <15>;
-					scan-delay = <32>;
-					row-hold = <91500>;
-				};
-
-				rtc@11d {
-					compatible = "qcom,pm8921-rtc";
-					interrupt-parent = <&pmicintc>;
-					interrupts = <39 1>;
-					reg = <0x11d>;
-					allow-set-time;
-				};
-			};
-		};
-
-		rng@1a500000 {
-			compatible = "qcom,prng";
-			reg = <0x1a500000 0x200>;
-			clocks = <&gcc PRNG_CLK>;
-			clock-names = "core";
-		};
-
-		amba {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-			sdcc1: mmc@12400000 {
-				status		= "disabled";
-				compatible	= "arm,pl18x", "arm,primecell";
-				arm,primecell-periphid = <0x00051180>;
-				reg		= <0x12400000 0x8000>;
-				interrupts	= <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <8>;
-				max-frequency	= <96000000>;
-				non-removable;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				vmmc-supply = <&vsdcc_fixed>;
-			};
-
-			sdcc3: mmc@12180000 {
-				compatible	= "arm,pl18x", "arm,primecell";
-				arm,primecell-periphid = <0x00051180>;
-				status		= "disabled";
-				reg		= <0x12180000 0x8000>;
-				interrupts	= <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <4>;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				max-frequency	= <192000000>;
-				no-1-8-v;
-				vmmc-supply = <&vsdcc_fixed>;
-			};
-		};
-
-		tcsr: syscon@1a400000 {
-			compatible = "qcom,tcsr-msm8960", "syscon";
-			reg = <0x1a400000 0x100>;
-		};
-
-		gsbi@16000000 {
-			compatible = "qcom,gsbi-v1.0.0";
-			cell-index = <1>;
-			reg = <0x16000000 0x100>;
-			clocks = <&gcc GSBI1_H_CLK>;
-			clock-names = "iface";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-
-			spi@16080000 {
-				compatible = "qcom,spi-qup-v1.1.1";
-				#address-cells = <1>;
-				#size-cells = <0>;
-				reg = <0x16080000 0x1000>;
-				interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
-				spi-max-frequency = <24000000>;
-				cs-gpios = <&msmgpio 8 0>;
-
-				clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>;
-				clock-names = "core", "iface";
-				status = "disabled";
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-msm8974-fairphone-fp2.dts b/arch/arm/boot/dts/qcom-msm8974-fairphone-fp2.dts
deleted file mode 100644
index 6d77e0f8ca4d..000000000000
--- a/arch/arm/boot/dts/qcom-msm8974-fairphone-fp2.dts
+++ /dev/null
@@ -1,409 +0,0 @@
-#include "qcom-msm8974.dtsi"
-#include "qcom-pm8841.dtsi"
-#include "qcom-pm8941.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-
-
-/ {
-	model = "Fairphone 2";
-	compatible = "fairphone,fp2", "qcom,msm8974";
-
-	aliases {
-		serial0 = &blsp1_uart2;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&gpio_keys_pin_a>;
-
-		camera-snapshot {
-			label = "camera_snapshot";
-			gpios = <&pm8941_gpios 1 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_CAMERA>;
-			wakeup-source;
-			debounce-interval = <15>;
-		};
-
-		volume-down {
-			label = "volume_down";
-			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEDOWN>;
-			wakeup-source;
-			debounce-interval = <15>;
-		};
-
-		volume-up {
-			label = "volume_up";
-			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEUP>;
-			wakeup-source;
-			debounce-interval = <15>;
-		};
-	};
-
-	vibrator {
-		compatible = "gpio-vibrator";
-		enable-gpios = <&msmgpio 86 GPIO_ACTIVE_HIGH>;
-		vcc-supply = <&pm8941_l18>;
-	};
-
-	smd {
-		rpm {
-			rpm_requests {
-				pm8841-regulators {
-					s1 {
-						regulator-min-microvolt = <675000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s2 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s3 {
-						regulator-min-microvolt = <1050000>;
-						regulator-max-microvolt = <1050000>;
-					};
-				};
-
-				pm8941-regulators {
-					vdd_l1_l3-supply = <&pm8941_s1>;
-					vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
-					vdd_l4_l11-supply = <&pm8941_s1>;
-					vdd_l5_l7-supply = <&pm8941_s2>;
-					vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
-					vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
-					vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
-					vdd_l21-supply = <&vreg_boost>;
-
-					s1 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					s2 {
-						regulator-min-microvolt = <2150000>;
-						regulator-max-microvolt = <2150000>;
-
-						regulator-boot-on;
-					};
-
-					s3 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l1 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l2 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					l3 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					l4 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					l5 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l6 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l7 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l8 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l9 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					l10 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					l11 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1350000>;
-					};
-
-					l12 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l13 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l14 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l15 {
-						regulator-min-microvolt = <2050000>;
-						regulator-max-microvolt = <2050000>;
-					};
-
-					l16 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l17 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					l18 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					l19 {
-						regulator-min-microvolt = <2900000>;
-						regulator-max-microvolt = <3350000>;
-					};
-
-					l20 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-						regulator-system-load = <200000>;
-						regulator-allow-set-load;
-					};
-
-					l21 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l22 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3300000>;
-					};
-
-					l23 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3000000>;
-					};
-
-					l24 {
-						regulator-min-microvolt = <3075000>;
-						regulator-max-microvolt = <3075000>;
-
-						regulator-boot-on;
-					};
-				};
-			};
-		};
-	};
-};
-
-&soc {
-	serial@f991e000 {
-		status = "okay";
-	};
-
-	remoteproc@fb21b000 {
-		status = "okay";
-
-		vddmx-supply = <&pm8841_s1>;
-		vddcx-supply = <&pm8841_s2>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&wcnss_pin_a>;
-
-		smd-edge {
-			qcom,remote-pid = <4>;
-			label = "pronto";
-
-			wcnss {
-				status = "okay";
-			};
-		};
-	};
-
-	pinctrl@fd510000 {
-		sdhc1_pin_a: sdhc1-pin-active {
-			clk {
-				pins = "sdc1_clk";
-				drive-strength = <16>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc1_cmd", "sdc1_data";
-				drive-strength = <10>;
-				bias-pull-up;
-			};
-		};
-
-		sdhc2_pin_a: sdhc2-pin-active {
-			clk {
-				pins = "sdc2_clk";
-				drive-strength = <10>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc2_cmd", "sdc2_data";
-				drive-strength = <6>;
-				bias-pull-up;
-			};
-		};
-
-		wcnss_pin_a: wcnss-pin-active {
-			wlan {
-				pins =  "gpio36", "gpio37", "gpio38", "gpio39", "gpio40";
-				function = "wlan";
-
-				drive-strength = <6>;
-				bias-pull-down;
-			};
-
-			bt {
-				pins = "gpio35", "gpio43", "gpio44";
-				function = "bt";
-
-				drive-strength = <2>;
-				bias-pull-down;
-			};
-
-			fm {
-				pins = "gpio41", "gpio42";
-				function = "fm";
-
-				drive-strength = <2>;
-				bias-pull-down;
-			};
-		};
-	};
-
-	sdhci@f9824900 {
-		status = "okay";
-
-		vmmc-supply = <&pm8941_l20>;
-		vqmmc-supply = <&pm8941_s3>;
-
-		bus-width = <8>;
-		non-removable;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc1_pin_a>;
-	};
-
-	sdhci@f98a4900 {
-		status = "okay";
-
-		vmmc-supply = <&pm8941_l21>;
-		vqmmc-supply = <&pm8941_l13>;
-
-		bus-width = <4>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc2_pin_a>;
-	};
-
-	usb@f9a55000 {
-		status = "okay";
-
-		phys = <&usb_hs1_phy>;
-		phy-select = <&tcsr 0xb000 0>;
-		extcon = <&smbb>, <&usb_id>;
-		vbus-supply = <&chg_otg>;
-
-		hnp-disable;
-		srp-disable;
-		adp-disable;
-
-		ulpi {
-			phy@a {
-				status = "okay";
-
-				v1p8-supply = <&pm8941_l6>;
-				v3p3-supply = <&pm8941_l24>;
-
-				extcon = <&smbb>;
-				qcom,init-seq = /bits/ 8 <0x1 0x64>;
-			};
-		};
-	};
-
-	imem@fe805000 {
-		status = "okay";
-
-		reboot-mode {
-			mode-normal	= <0x77665501>;
-			mode-bootloader	= <0x77665500>;
-			mode-recovery	= <0x77665502>;
-		};
-	};
-};
-
-&spmi_bus {
-	pm8941@0 {
-		gpios@c000 {
-			gpio_keys_pin_a: gpio-keys-active {
-				pins = "gpio1", "gpio2", "gpio5";
-				function = "normal";
-
-				bias-pull-up;
-				power-source = <PM8941_GPIO_S3>;
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
deleted file mode 100644
index 069136170198..000000000000
--- a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
+++ /dev/null
@@ -1,761 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-msm8974.dtsi"
-#include "qcom-pm8841.dtsi"
-#include "qcom-pm8941.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-
-/ {
-	model = "LGE MSM 8974 HAMMERHEAD";
-	compatible = "lge,hammerhead", "qcom,msm8974";
-
-	aliases {
-		serial0 = &blsp1_uart1;
-		serial1 = &blsp2_uart10;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	smd {
-		rpm {
-			rpm_requests {
-				pm8841-regulators {
-					s1 {
-						regulator-min-microvolt = <675000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s2 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s3 {
-						regulator-min-microvolt = <1050000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s4 {
-						regulator-min-microvolt = <815000>;
-						regulator-max-microvolt = <900000>;
-					};
-				};
-
-				pm8941-regulators {
-					vdd_l1_l3-supply = <&pm8941_s1>;
-					vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
-					vdd_l4_l11-supply = <&pm8941_s1>;
-					vdd_l5_l7-supply = <&pm8941_s2>;
-					vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
-					vdd_l8_l16_l18_l19-supply = <&vreg_vph_pwr>;
-					vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
-					vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
-					vdd_l21-supply = <&vreg_boost>;
-
-					s1 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					s2 {
-						regulator-min-microvolt = <2150000>;
-						regulator-max-microvolt = <2150000>;
-
-						regulator-boot-on;
-					};
-
-					s3 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l1 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l2 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					l3 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					l4 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					l5 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l6 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l7 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l8 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l9 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					l10 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					l11 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-					};
-
-					l12 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l13 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l14 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l15 {
-						regulator-min-microvolt = <2050000>;
-						regulator-max-microvolt = <2050000>;
-					};
-
-					l16 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l17 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					l18 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					l19 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3300000>;
-					};
-
-					l20 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-						regulator-system-load = <200000>;
-						regulator-allow-set-load;
-					};
-
-					l21 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l22 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3300000>;
-					};
-
-					l23 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3000000>;
-					};
-
-					l24 {
-						regulator-min-microvolt = <3075000>;
-						regulator-max-microvolt = <3075000>;
-
-						regulator-boot-on;
-					};
-				};
-			};
-		};
-	};
-
-	vreg_wlan: wlan-regulator {
-		compatible = "regulator-fixed";
-
-		regulator-name = "wl-reg";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&msmgpio 26 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&wlan_regulator_pin>;
-	};
-};
-
-&soc {
-	serial@f991d000 {
-		status = "okay";
-	};
-
-	pinctrl@fd510000 {
-		sdhc1_pin_a: sdhc1-pin-active {
-			clk {
-				pins = "sdc1_clk";
-				drive-strength = <16>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc1_cmd", "sdc1_data";
-				drive-strength = <10>;
-				bias-pull-up;
-			};
-		};
-
-		sdhc2_pin_a: sdhc2-pin-active {
-			clk {
-				pins = "sdc2_clk";
-				drive-strength = <6>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc2_cmd", "sdc2_data";
-				drive-strength = <6>;
-				bias-pull-up;
-			};
-		};
-
-		i2c1_pins: i2c1 {
-			mux {
-				pins = "gpio2", "gpio3";
-				function = "blsp_i2c1";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		i2c2_pins: i2c2 {
-			mux {
-				pins = "gpio6", "gpio7";
-				function = "blsp_i2c2";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		i2c3_pins: i2c3 {
-			mux {
-				pins = "gpio10", "gpio11";
-				function = "blsp_i2c3";
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		i2c11_pins: i2c11 {
-			mux {
-				pins = "gpio83", "gpio84";
-				function = "blsp_i2c11";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		i2c12_pins: i2c12 {
-			mux {
-				pins = "gpio87", "gpio88";
-				function = "blsp_i2c12";
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		mpu6515_pin: mpu6515 {
-			irq {
-				pins = "gpio73";
-				function = "gpio";
-				bias-disable;
-				input-enable;
-			};
-		};
-
-		touch_pin: touch {
-			int {
-				pins = "gpio5";
-				function = "gpio";
-
-				drive-strength = <2>;
-				bias-disable;
-				input-enable;
-			};
-
-			reset {
-				pins = "gpio8";
-				function = "gpio";
-
-				drive-strength = <2>;
-				bias-pull-up;
-			};
-		};
-
-		panel_pin: panel {
-			te {
-				pins = "gpio12";
-				function = "mdp_vsync";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		bt_pin: bt {
-			hostwake {
-				pins = "gpio42";
-				function = "gpio";
-			};
-
-			devwake {
-				pins = "gpio62";
-				function = "gpio";
-			};
-
-			shutdown {
-				pins = "gpio41";
-				function = "gpio";
-			};
-		};
-
-		blsp2_uart10_pin_a: blsp2-uart10-pin-active {
-			tx {
-				pins = "gpio53";
-				function = "blsp_uart10";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-
-			rx {
-				pins = "gpio54";
-				function = "blsp_uart10";
-
-				drive-strength = <2>;
-				bias-pull-up;
-			};
-
-			cts {
-				pins = "gpio55";
-				function = "blsp_uart10";
-
-				drive-strength = <2>;
-				bias-pull-up;
-			};
-
-			rts {
-				pins = "gpio56";
-				function = "blsp_uart10";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-	};
-
-	sdhci@f9824900 {
-		status = "okay";
-
-		vmmc-supply = <&pm8941_l20>;
-		vqmmc-supply = <&pm8941_s3>;
-
-		bus-width = <8>;
-		non-removable;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc1_pin_a>;
-	};
-
-	sdhci@f98a4900 {
-		status = "okay";
-
-		max-frequency = <100000000>;
-		bus-width = <4>;
-		non-removable;
-		vmmc-supply = <&vreg_wlan>;
-		vqmmc-supply = <&pm8941_s3>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc2_pin_a>;
-
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		bcrmf@1 {
-			compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac";
-			reg = <1>;
-
-			brcm,drive-strength = <10>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&wlan_sleep_clk_pin>;
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&gpio_keys_pin_a>;
-
-		volume-up {
-			label = "volume_up";
-			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEUP>;
-		};
-
-		volume-down {
-			label = "volume_down";
-			gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEDOWN>;
-		};
-	};
-
-	serial@f9960000 {
-		status = "okay";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&blsp2_uart10_pin_a>;
-
-		bluetooth {
-			compatible = "brcm,bcm43438-bt";
-			max-speed = <3000000>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&bt_pin>;
-
-			host-wakeup-gpios = <&msmgpio 42 GPIO_ACTIVE_HIGH>;
-			device-wakeup-gpios = <&msmgpio 62 GPIO_ACTIVE_HIGH>;
-			shutdown-gpios = <&msmgpio 41 GPIO_ACTIVE_HIGH>;
-		};
-	};
-
-	i2c@f9967000 {
-		status = "okay";
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c11_pins>;
-		clock-frequency = <355000>;
-		qcom,src-freq = <50000000>;
-
-		led-controller@38 {
-			compatible = "ti,lm3630a";
-			status = "okay";
-			reg = <0x38>;
-
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			led@0 {
-				reg = <0>;
-				led-sources = <0 1>;
-				label = "lcd-backlight";
-				default-brightness = <200>;
-			};
-		};
-	};
-
-	i2c@f9968000 {
-		status = "okay";
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c12_pins>;
-		clock-frequency = <100000>;
-		qcom,src-freq = <50000000>;
-
-		mpu6515@68 {
-			compatible = "invensense,mpu6515";
-			reg = <0x68>;
-			interrupts-extended = <&msmgpio 73 IRQ_TYPE_EDGE_FALLING>;
-			vddio-supply = <&pm8941_lvs1>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&mpu6515_pin>;
-
-			mount-matrix = "0", "-1", "0",
-				       "-1", "0", "0",
-				       "0", "0", "1";
-
-			i2c-gate {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				ak8963@f {
-					compatible = "asahi-kasei,ak8963";
-					reg = <0x0f>;
-					gpios = <&msmgpio 67 0>;
-					vid-supply = <&pm8941_lvs1>;
-					vdd-supply = <&pm8941_l17>;
-				};
-
-				bmp280@76 {
-					compatible = "bosch,bmp280";
-					reg = <0x76>;
-					vdda-supply = <&pm8941_lvs1>;
-					vddd-supply = <&pm8941_l17>;
-				};
-			};
-		};
-	};
-
-	i2c@f9923000 {
-		status = "okay";
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c1_pins>;
-		clock-frequency = <100000>;
-		qcom,src-freq = <50000000>;
-
-		charger: bq24192@6b {
-			compatible = "ti,bq24192";
-			reg = <0x6b>;
-			interrupts-extended = <&spmi_bus 0 0xd5 0 IRQ_TYPE_EDGE_FALLING>;
-
-			omit-battery-class;
-
-			usb_otg_vbus: usb-otg-vbus { };
-		};
-
-		fuelgauge: max17048@36 {
-			compatible = "maxim,max17048";
-			reg = <0x36>;
-
-			maxim,double-soc;
-			maxim,rcomp = /bits/ 8 <0x4d>;
-
-			interrupt-parent = <&msmgpio>;
-			interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&fuelgauge_pin>;
-
-			maxim,alert-low-soc-level = <2>;
-		};
-	};
-
-	i2c@f9924000 {
-		status = "okay";
-
-		clock-frequency = <355000>;
-		qcom,src-freq = <50000000>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c2_pins>;
-
-		synaptics@70 {
-			compatible = "syna,rmi4-i2c";
-			reg = <0x70>;
-
-			interrupts-extended = <&msmgpio 5 IRQ_TYPE_EDGE_FALLING>;
-			vdd-supply = <&pm8941_l22>;
-			vio-supply = <&pm8941_lvs3>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&touch_pin>;
-
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			rmi4-f01@1 {
-				reg = <0x1>;
-				syna,nosleep-mode = <1>;
-			};
-
-			rmi4-f12@12 {
-				reg = <0x12>;
-				syna,sensor-type = <1>;
-			};
-		};
-	};
-
-	i2c@f9925000 {
-		status = "okay";
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c3_pins>;
-		clock-frequency = <100000>;
-		qcom,src-freq = <50000000>;
-
-		avago_apds993@39 {
-			compatible = "avago,apds9930";
-			reg = <0x39>;
-			interrupts-extended = <&msmgpio 61 IRQ_TYPE_EDGE_FALLING>;
-			vdd-supply = <&pm8941_l17>;
-			vddio-supply = <&pm8941_lvs1>;
-			led-max-microamp = <100000>;
-			amstaos,proximity-diodes = <0>;
-		};
-	};
-
-	usb@f9a55000 {
-		status = "okay";
-
-		phys = <&usb_hs1_phy>;
-		phy-select = <&tcsr 0xb000 0>;
-
-		extcon = <&charger>, <&usb_id>;
-		vbus-supply = <&usb_otg_vbus>;
-
-		hnp-disable;
-		srp-disable;
-		adp-disable;
-
-		ulpi {
-			phy@a {
-				status = "okay";
-
-				v1p8-supply = <&pm8941_l6>;
-				v3p3-supply = <&pm8941_l24>;
-
-				qcom,init-seq = /bits/ 8 <0x1 0x64>;
-			};
-		};
-	};
-
-	mdss@fd900000 {
-		status = "okay";
-
-		mdp@fd900000 {
-			status = "okay";
-		};
-
-		dsi@fd922800 {
-			status = "okay";
-
-			vdda-supply = <&pm8941_l2>;
-			vdd-supply = <&pm8941_lvs3>;
-			vddio-supply = <&pm8941_l12>;
-
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			ports {
-				port@1 {
-					endpoint {
-						remote-endpoint = <&panel_in>;
-						data-lanes = <0 1 2 3>;
-					};
-				};
-			};
-
-			panel: panel@0 {
-				reg = <0>;
-				compatible = "lg,acx467akm-7";
-
-				pinctrl-names = "default";
-				pinctrl-0 = <&panel_pin>;
-
-				port {
-					panel_in: endpoint {
-						remote-endpoint = <&dsi0_out>;
-					};
-				};
-			};
-		};
-
-		dsi-phy@fd922a00 {
-			status = "okay";
-
-			vddio-supply = <&pm8941_l12>;
-		};
-	};
-};
-
-&spmi_bus {
-	pm8941@0 {
-		gpios@c000 {
-			gpio_keys_pin_a: gpio-keys-active {
-				pins = "gpio2", "gpio3";
-				function = "normal";
-
-				bias-pull-up;
-				power-source = <PM8941_GPIO_S3>;
-			};
-
-			fuelgauge_pin: fuelgauge-int {
-				pins = "gpio9";
-				function = "normal";
-
-				bias-disable;
-				input-enable;
-				power-source = <PM8941_GPIO_S3>;
-			};
-
-			wlan_sleep_clk_pin: wl-sleep-clk {
-				pins = "gpio16";
-				function = "func2";
-
-				output-high;
-				power-source = <PM8941_GPIO_S3>;
-			};
-
-			wlan_regulator_pin: wl-reg-active {
-				pins = "gpio17";
-				function = "normal";
-
-				bias-disable;
-				power-source = <PM8941_GPIO_S3>;
-			};
-
-			otg {
-				gpio-hog;
-				gpios = <35 GPIO_ACTIVE_HIGH>;
-				output-high;
-				line-name = "otg-gpio";
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts b/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts
deleted file mode 100644
index 96e1c978b878..000000000000
--- a/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts
+++ /dev/null
@@ -1,908 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-msm8974pro.dtsi"
-#include "qcom-pma8084.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-#include <dt-bindings/leds/common.h>
-
-/ {
-	model = "Samsung Galaxy S5";
-	compatible = "samsung,klte", "qcom,msm8974";
-
-	aliases {
-		serial0 = &blsp1_uart1;
-		mmc0 = &sdhc_1; /* SDC1 eMMC slot */
-		mmc1 = &sdhc_2; /* SDC2 SD card slot */
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	smd {
-		rpm {
-			rpm_requests {
-				pma8084-regulators {
-					compatible = "qcom,rpm-pma8084-regulators";
-					status = "okay";
-
-					pma8084_s1: s1 {
-						regulator-min-microvolt = <675000>;
-						regulator-max-microvolt = <1050000>;
-						regulator-always-on;
-					};
-
-					pma8084_s2: s2 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					pma8084_s3: s3 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-					};
-
-					pma8084_s4: s4 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					pma8084_s5: s5 {
-						regulator-min-microvolt = <2150000>;
-						regulator-max-microvolt = <2150000>;
-					};
-
-					pma8084_s6: s6 {
-						regulator-min-microvolt = <1050000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					pma8084_l1: l1 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					pma8084_l2: l2 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					pma8084_l3: l3 {
-						regulator-min-microvolt = <1050000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					pma8084_l4: l4 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					pma8084_l5: l5 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					pma8084_l6: l6 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					pma8084_l7: l7 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					pma8084_l8: l8 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					pma8084_l9: l9 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					pma8084_l10: l10 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					pma8084_l11: l11 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-					};
-
-					pma8084_l12: l12 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-						regulator-always-on;
-					};
-
-					pma8084_l13: l13 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					pma8084_l14: l14 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					pma8084_l15: l15 {
-						regulator-min-microvolt = <2050000>;
-						regulator-max-microvolt = <2050000>;
-					};
-
-					pma8084_l16: l16 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					pma8084_l17: l17 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					pma8084_l18: l18 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					pma8084_l19: l19 {
-						regulator-min-microvolt = <3300000>;
-						regulator-max-microvolt = <3300000>;
-					};
-
-					pma8084_l20: l20 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-allow-set-load;
-						regulator-system-load = <200000>;
-					};
-
-					pma8084_l21: l21 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-allow-set-load;
-						regulator-system-load = <200000>;
-					};
-
-					pma8084_l22: l22 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3300000>;
-					};
-
-					pma8084_l23: l23 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3000000>;
-					};
-
-					pma8084_l24: l24 {
-						regulator-min-microvolt = <3075000>;
-						regulator-max-microvolt = <3075000>;
-					};
-
-					pma8084_l25: l25 {
-						regulator-min-microvolt = <2100000>;
-						regulator-max-microvolt = <2100000>;
-					};
-
-					pma8084_l26: l26 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2050000>;
-					};
-
-					pma8084_l27: l27 {
-						regulator-min-microvolt = <1000000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					pma8084_lvs1: lvs1 {};
-					pma8084_lvs2: lvs2 {};
-					pma8084_lvs3: lvs3 {};
-					pma8084_lvs4: lvs4 {};
-
-					pma8084_5vs1: 5vs1 {};
-				};
-			};
-		};
-	};
-
-	i2c-gpio-touchkey {
-		compatible = "i2c-gpio";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		sda-gpios = <&msmgpio 95 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-		scl-gpios = <&msmgpio 96 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c_touchkey_pins>;
-
-		touchkey@20 {
-			compatible = "cypress,tm2-touchkey";
-			reg = <0x20>;
-
-			interrupt-parent = <&pma8084_gpios>;
-			interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&touchkey_pin>;
-
-			vcc-supply = <&max77826_ldo15>;
-			vdd-supply = <&pma8084_l19>;
-
-			linux,keycodes = <KEY_APPSELECT KEY_BACK>;
-		};
-	};
-
-	i2c-gpio-led {
-		compatible = "i2c-gpio";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		scl-gpios = <&msmgpio 121 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-		sda-gpios = <&msmgpio 120 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c_led_gpioex_pins>;
-
-		i2c-gpio,delay-us = <2>;
-
-		gpio_expander: gpio@20 {
-			compatible = "nxp,pcal6416";
-			reg = <0x20>;
-
-			gpio-controller;
-			#gpio-cells = <2>;
-
-			vcc-supply = <&pma8084_s4>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&gpioex_pin>;
-
-			reset-gpios = <&msmgpio 145 GPIO_ACTIVE_LOW>;
-		};
-
-		led-controller@30 {
-			compatible = "panasonic,an30259a";
-			reg = <0x30>;
-
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			led@1 {
-				reg = <1>;
-				function = LED_FUNCTION_STATUS;
-				color = <LED_COLOR_ID_RED>;
-			};
-
-			led@2 {
-				reg = <2>;
-				function = LED_FUNCTION_STATUS;
-				color = <LED_COLOR_ID_GREEN>;
-			};
-
-			led@3 {
-				reg = <3>;
-				function = LED_FUNCTION_STATUS;
-				color = <LED_COLOR_ID_BLUE>;
-			};
-		};
-	};
-
-	vreg_wlan: wlan-regulator {
-		compatible = "regulator-fixed";
-
-		regulator-name = "wl-reg";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&gpio_expander 8 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vreg_panel: panel-regulator {
-		compatible = "regulator-fixed";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&panel_en_pin>;
-
-		regulator-name = "panel-vddr-reg";
-		regulator-min-microvolt = <1500000>;
-		regulator-max-microvolt = <1500000>;
-
-		gpio = <&pma8084_gpios 14 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	/delete-node/ vreg-boost;
-
-	adsp-pil {
-		cx-supply = <&pma8084_s2>;
-	};
-};
-
-&soc {
-	serial@f991e000 {
-		status = "okay";
-	};
-
-	/* blsp2_uart8 */
-	serial@f995e000 {
-		status = "okay";
-
-		pinctrl-names = "default", "sleep";
-		pinctrl-0 = <&blsp2_uart8_pins_active>;
-		pinctrl-1 = <&blsp2_uart8_pins_sleep>;
-
-		bluetooth {
-			compatible = "brcm,bcm43540-bt";
-			max-speed = <3000000>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&bt_pins>;
-			device-wakeup-gpios = <&msmgpio 91 GPIO_ACTIVE_HIGH>;
-			shutdown-gpios = <&gpio_expander 9 GPIO_ACTIVE_HIGH>;
-			interrupt-parent = <&msmgpio>;
-			interrupts = <75 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "host-wakeup";
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&gpio_keys_pin_a>;
-
-		volume-down {
-			label = "volume_down";
-			gpios = <&pma8084_gpios 2 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEDOWN>;
-			debounce-interval = <15>;
-		};
-
-		home-key {
-			label = "home_key";
-			gpios = <&pma8084_gpios 3 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_HOMEPAGE>;
-			wakeup-source;
-			debounce-interval = <15>;
-		};
-
-		volume-up {
-			label = "volume_up";
-			gpios = <&pma8084_gpios 5 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEUP>;
-			debounce-interval = <15>;
-		};
-	};
-
-	pinctrl@fd510000 {
-		blsp2_uart8_pins_active: blsp2-uart8-pins-active {
-			pins = "gpio45", "gpio46", "gpio47", "gpio48";
-			function = "blsp_uart8";
-			drive-strength = <8>;
-			bias-disable;
-		};
-
-		blsp2_uart8_pins_sleep: blsp2-uart8-pins-sleep {
-			pins = "gpio45", "gpio46", "gpio47", "gpio48";
-			function = "gpio";
-			drive-strength = <2>;
-			bias-pull-down;
-		};
-
-		bt_pins: bt-pins {
-			hostwake {
-				pins = "gpio75";
-				function = "gpio";
-				drive-strength = <16>;
-				input-enable;
-			};
-
-			devwake {
-				pins = "gpio91";
-				function = "gpio";
-				drive-strength = <2>;
-			};
-		};
-
-		sdhc1_pin_a: sdhc1-pin-active {
-			clk {
-				pins = "sdc1_clk";
-				drive-strength = <4>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc1_cmd", "sdc1_data";
-				drive-strength = <4>;
-				bias-pull-up;
-			};
-		};
-
-		sdhc2_pin_a: sdhc2-pin-active {
-			clk-cmd-data {
-				pins = "gpio35", "gpio36", "gpio37", "gpio38",
-					"gpio39", "gpio40";
-				function = "sdc3";
-				drive-strength = <8>;
-				bias-disable;
-			};
-		};
-
-		sdhc2_cd_pin: sdhc2-cd {
-			pins = "gpio62";
-			function = "gpio";
-
-			drive-strength = <2>;
-			bias-disable;
-		};
-
-		sdhc3_pin_a: sdhc3-pin-active {
-			clk {
-				pins = "sdc2_clk";
-				drive-strength = <6>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc2_cmd", "sdc2_data";
-				drive-strength = <6>;
-				bias-pull-up;
-			};
-		};
-
-		i2c2_pins: i2c2 {
-			mux {
-				pins = "gpio6", "gpio7";
-				function = "blsp_i2c2";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		i2c6_pins: i2c6 {
-			mux {
-				pins = "gpio29", "gpio30";
-				function = "blsp_i2c6";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		i2c12_pins: i2c12 {
-			mux {
-				pins = "gpio87", "gpio88";
-				function = "blsp_i2c12";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		i2c_touchkey_pins: i2c-touchkey {
-			mux {
-				pins = "gpio95", "gpio96";
-				function = "gpio";
-				input-enable;
-				bias-pull-up;
-			};
-		};
-
-		i2c_led_gpioex_pins: i2c-led-gpioex {
-			mux {
-				pins = "gpio120", "gpio121";
-				function = "gpio";
-				input-enable;
-				bias-pull-down;
-			};
-		};
-
-		gpioex_pin: gpioex {
-			res {
-				pins = "gpio145";
-				function = "gpio";
-
-				bias-pull-up;
-				drive-strength = <2>;
-			};
-		};
-
-		wifi_pin: wifi {
-			int {
-				pins = "gpio92";
-				function = "gpio";
-
-				input-enable;
-				bias-pull-down;
-			};
-		};
-
-		panel_te_pin: panel {
-			te {
-				pins = "gpio12";
-				function = "mdp_vsync";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-	};
-
-	sdhc_1: sdhci@f9824900 {
-		status = "okay";
-
-		vmmc-supply = <&pma8084_l20>;
-		vqmmc-supply = <&pma8084_s4>;
-
-		bus-width = <8>;
-		non-removable;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc1_pin_a>;
-	};
-
-	sdhc_2: sdhci@f9864900 {
-		status = "okay";
-
-		max-frequency = <100000000>;
-
-		vmmc-supply = <&pma8084_l21>;
-		vqmmc-supply = <&pma8084_l13>;
-
-		bus-width = <4>;
-
-		/* cd-gpio is intentionally disabled. If enabled, an SD card
-		 * present during boot is not initialized correctly. Without
-		 * cd-gpios the driver resorts to polling, so hotplug works.
-		 */
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc2_pin_a /* &sdhc2_cd_pin */>;
-		// cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
-	};
-
-	sdhci@f98a4900 {
-		status = "okay";
-
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		max-frequency = <100000000>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc3_pin_a>;
-
-		vmmc-supply = <&vreg_wlan>;
-		vqmmc-supply = <&pma8084_s4>;
-
-		bus-width = <4>;
-		non-removable;
-
-		wifi@1 {
-			reg = <1>;
-			compatible = "brcm,bcm4329-fmac";
-
-			interrupt-parent = <&msmgpio>;
-			interrupts = <92 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "host-wake";
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&wlan_sleep_clk_pin &wifi_pin>;
-		};
-	};
-
-	usb@f9a55000 {
-		status = "okay";
-
-		phys = <&usb_hs1_phy>;
-		phy-select = <&tcsr 0xb000 0>;
-		/*extcon = <&smbb>, <&usb_id>;*/
-		/*vbus-supply = <&chg_otg>;*/
-
-		hnp-disable;
-		srp-disable;
-		adp-disable;
-
-		ulpi {
-			phy@a {
-				status = "okay";
-
-				v1p8-supply = <&pma8084_l6>;
-				v3p3-supply = <&pma8084_l24>;
-
-				/*extcon = <&smbb>;*/
-				qcom,init-seq = /bits/ 8 <0x1 0x64>;
-			};
-		};
-	};
-
-	i2c@f9924000 {
-		status = "okay";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c2_pins>;
-
-		touchscreen@20 {
-			compatible = "syna,rmi4-i2c";
-			reg = <0x20>;
-
-			interrupt-parent = <&pma8084_gpios>;
-			interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
-
-			vdd-supply = <&max77826_ldo13>;
-			vio-supply = <&pma8084_lvs2>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&touch_pin>;
-
-			syna,startup-delay-ms = <100>;
-
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			rmi4-f01@1 {
-				reg = <0x1>;
-				syna,nosleep-mode = <1>;
-			};
-
-			rmi4-f12@12 {
-				reg = <0x12>;
-				syna,sensor-type = <1>;
-			};
-		};
-	};
-
-	i2c@f9928000 {
-		status = "okay";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c6_pins>;
-
-		pmic@60 {
-			reg = <0x60>;
-			compatible = "maxim,max77826";
-
-			regulators {
-				max77826_ldo1: LDO1 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-				};
-
-				max77826_ldo2: LDO2 {
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1000000>;
-				};
-
-				max77826_ldo3: LDO3 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-				};
-
-				max77826_ldo4: LDO4 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				max77826_ldo5: LDO5 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				max77826_ldo6: LDO6 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <3300000>;
-				};
-
-				max77826_ldo7: LDO7 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				max77826_ldo8: LDO8 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <3300000>;
-				};
-
-				max77826_ldo9: LDO9 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				max77826_ldo10: LDO10 {
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2950000>;
-				};
-
-				max77826_ldo11: LDO11 {
-					regulator-min-microvolt = <2700000>;
-					regulator-max-microvolt = <2950000>;
-				};
-
-				max77826_ldo12: LDO12 {
-					regulator-min-microvolt = <2500000>;
-					regulator-max-microvolt = <3300000>;
-				};
-
-				max77826_ldo13: LDO13 {
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-				};
-
-				max77826_ldo14: LDO14 {
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-				};
-
-				max77826_ldo15: LDO15 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				max77826_buck: BUCK {
-					regulator-min-microvolt = <1225000>;
-					regulator-max-microvolt = <1225000>;
-				};
-
-				max77826_buckboost: BUCKBOOST {
-					regulator-min-microvolt = <3400000>;
-					regulator-max-microvolt = <3400000>;
-				};
-			};
-		};
-	};
-
-	i2c@f9968000 {
-		status = "okay";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c12_pins>;
-
-		fuelgauge@36 {
-			compatible = "maxim,max17048";
-			reg = <0x36>;
-
-			maxim,double-soc;
-			maxim,rcomp = /bits/ 8 <0x56>;
-
-			interrupt-parent = <&pma8084_gpios>;
-			interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&fuelgauge_pin>;
-		};
-	};
-
-	adreno@fdb00000 {
-		status = "ok";
-	};
-
-	mdss@fd900000 {
-		status = "ok";
-
-		mdp@fd900000 {
-			status = "ok";
-		};
-
-		dsi@fd922800 {
-			status = "ok";
-
-			vdda-supply = <&pma8084_l2>;
-			vdd-supply = <&pma8084_l22>;
-			vddio-supply = <&pma8084_l12>;
-
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			ports {
-				port@1 {
-					endpoint {
-						remote-endpoint = <&panel_in>;
-						data-lanes = <0 1 2 3>;
-					};
-				};
-			};
-
-			panel: panel@0 {
-				reg = <0>;
-				compatible = "samsung,s6e3fa2";
-
-				pinctrl-names = "default";
-				pinctrl-0 = <&panel_te_pin &panel_rst_pin>;
-
-				iovdd-supply = <&pma8084_lvs4>;
-				vddr-supply = <&vreg_panel>;
-
-				reset-gpios = <&pma8084_gpios 17 GPIO_ACTIVE_LOW>;
-				te-gpios = <&msmgpio 12 GPIO_ACTIVE_HIGH>;
-
-				port {
-					panel_in: endpoint {
-						remote-endpoint = <&dsi0_out>;
-					};
-				};
-			};
-		};
-
-		dsi-phy@fd922a00 {
-			status = "ok";
-
-			vddio-supply = <&pma8084_l12>;
-		};
-	};
-
-	remoteproc@fc880000 {
-		cx-supply = <&pma8084_s2>;
-		mss-supply = <&pma8084_s6>;
-		mx-supply = <&pma8084_s1>;
-		pll-supply = <&pma8084_l12>;
-	};
-};
-
-&spmi_bus {
-	pma8084@0 {
-		gpios@c000 {
-			gpio_keys_pin_a: gpio-keys-active {
-				pins = "gpio2", "gpio3", "gpio5";
-				function = "normal";
-
-				bias-pull-up;
-				power-source = <PMA8084_GPIO_S4>;
-			};
-
-			touchkey_pin: touchkey-int-pin {
-				pins = "gpio6";
-				function = "normal";
-				bias-disable;
-				input-enable;
-				power-source = <PMA8084_GPIO_S4>;
-			};
-
-			touch_pin: touchscreen-int-pin {
-				pins = "gpio8";
-				function = "normal";
-				bias-disable;
-				input-enable;
-				power-source = <PMA8084_GPIO_S4>;
-			};
-
-			panel_en_pin: panel-en-pin {
-				pins = "gpio14";
-				function = "normal";
-				bias-pull-up;
-				power-source = <PMA8084_GPIO_S4>;
-				qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
-			};
-
-			wlan_sleep_clk_pin: wlan-sleep-clk-pin {
-				pins = "gpio16";
-				function = "func2";
-
-				output-high;
-				power-source = <PMA8084_GPIO_S4>;
-				qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>;
-			};
-
-			panel_rst_pin: panel-rst-pin {
-				pins = "gpio17";
-				function = "normal";
-				bias-disable;
-				power-source = <PMA8084_GPIO_S4>;
-				qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
-			};
-
-
-			fuelgauge_pin: fuelgauge-int-pin {
-				pins = "gpio21";
-				function = "normal";
-				bias-disable;
-				input-enable;
-				power-source = <PMA8084_GPIO_S4>;
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-amami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-amami.dts
deleted file mode 100644
index 79e2cfbbb1ba..000000000000
--- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-amami.dts
+++ /dev/null
@@ -1,435 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-msm8974.dtsi"
-#include "qcom-pm8841.dtsi"
-#include "qcom-pm8941.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-
-/ {
-	model = "Sony Xperia Z1 Compact";
-	compatible = "sony,xperia-amami", "qcom,msm8974";
-
-	aliases {
-		serial0 = &blsp1_uart2;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&gpio_keys_pin_a>;
-
-		volume-down {
-			label = "volume_down";
-			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEDOWN>;
-		};
-
-		camera-snapshot {
-			label = "camera_snapshot";
-			gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_CAMERA>;
-		};
-
-		camera-focus {
-			label = "camera_focus";
-			gpios = <&pm8941_gpios 4 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_CAMERA_FOCUS>;
-		};
-
-		volume-up {
-			label = "volume_up";
-			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEUP>;
-		};
-	};
-
-	memory@0 {
-		reg = <0 0x40000000>, <0x40000000 0x40000000>;
-		device_type = "memory";
-	};
-
-	smd {
-		rpm {
-			rpm_requests {
-				pm8841-regulators {
-					s1 {
-						regulator-min-microvolt = <675000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s2 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s3 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s4 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-				};
-
-				pm8941-regulators {
-					vdd_l1_l3-supply = <&pm8941_s1>;
-					vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
-					vdd_l4_l11-supply = <&pm8941_s1>;
-					vdd_l5_l7-supply = <&pm8941_s2>;
-					vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
-					vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
-					vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
-					vdd_l21-supply = <&vreg_boost>;
-
-					s1 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					s2 {
-						regulator-min-microvolt = <2150000>;
-						regulator-max-microvolt = <2150000>;
-						regulator-boot-on;
-					};
-
-					s3 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					s4 {
-						regulator-min-microvolt = <5000000>;
-						regulator-max-microvolt = <5000000>;
-					};
-
-					l1 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l2 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					l3 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					l4 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					l5 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l6 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l7 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l8 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l9 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					l11 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1350000>;
-					};
-
-					l12 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l13 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l14 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l15 {
-						regulator-min-microvolt = <2050000>;
-						regulator-max-microvolt = <2050000>;
-					};
-
-					l16 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l17 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l18 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					l19 {
-						regulator-min-microvolt = <3300000>;
-						regulator-max-microvolt = <3300000>;
-					};
-
-					l20 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-allow-set-load;
-						regulator-boot-on;
-						regulator-system-load = <200000>;
-					};
-
-					l21 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l22 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3000000>;
-					};
-
-					l23 {
-						regulator-min-microvolt = <2800000>;
-						regulator-max-microvolt = <2800000>;
-					};
-
-					l24 {
-						regulator-min-microvolt = <3075000>;
-						regulator-max-microvolt = <3075000>;
-
-						regulator-boot-on;
-					};
-				};
-			};
-		};
-	};
-};
-
-&soc {
-	sdhci@f9824900 {
-		status = "okay";
-
-		vmmc-supply = <&pm8941_l20>;
-		vqmmc-supply = <&pm8941_s3>;
-
-		bus-width = <8>;
-		non-removable;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc1_pin_a>;
-	};
-
-	sdhci@f98a4900 {
-		status = "okay";
-
-		bus-width = <4>;
-
-		vmmc-supply = <&pm8941_l21>;
-		vqmmc-supply = <&pm8941_l13>;
-
-		cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
-	};
-
-	serial@f991e000 {
-		status = "okay";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&blsp1_uart2_pin_a>;
-	};
-
-
-	pinctrl@fd510000 {
-		blsp1_uart2_pin_a: blsp1-uart2-pin-active {
-			rx {
-				pins = "gpio5";
-				function = "blsp_uart2";
-
-				drive-strength = <2>;
-				bias-pull-up;
-			};
-
-			tx {
-				pins = "gpio4";
-				function = "blsp_uart2";
-
-				drive-strength = <4>;
-				bias-disable;
-			};
-		};
-
-		i2c2_pins: i2c2 {
-			mux {
-				pins = "gpio6", "gpio7";
-				function = "blsp_i2c2";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		sdhc1_pin_a: sdhc1-pin-active {
-			clk {
-				pins = "sdc1_clk";
-				drive-strength = <16>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc1_cmd", "sdc1_data";
-				drive-strength = <10>;
-				bias-pull-up;
-			};
-		};
-
-		sdhc2_cd_pin_a: sdhc2-cd-pin-active {
-			pins = "gpio62";
-			function = "gpio";
-
-			drive-strength = <2>;
-			bias-disable;
-		 };
-
-		sdhc2_pin_a: sdhc2-pin-active {
-			clk {
-				pins = "sdc2_clk";
-				drive-strength = <10>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc2_cmd", "sdc2_data";
-				drive-strength = <6>;
-				bias-pull-up;
-			};
-		};
-	};
-
-	dma-controller@f9944000 {
-		qcom,controlled-remotely;
-	};
-
-	usb@f9a55000 {
-		status = "okay";
-
-		phys = <&usb_hs1_phy>;
-		phy-select = <&tcsr 0xb000 0>;
-		extcon = <&smbb>, <&usb_id>;
-		vbus-supply = <&chg_otg>;
-
-		hnp-disable;
-		srp-disable;
-		adp-disable;
-
-		ulpi {
-			phy@a {
-				status = "okay";
-
-				v1p8-supply = <&pm8941_l6>;
-				v3p3-supply = <&pm8941_l24>;
-
-				extcon = <&smbb>;
-				qcom,init-seq = /bits/ 8 <0x1 0x64>;
-			};
-		};
-	};
-};
-
-&spmi_bus {
-	pm8941@0 {
-		charger@1000 {
-			qcom,fast-charge-safe-current = <1300000>;
-			qcom,fast-charge-current-limit = <1300000>;
-			qcom,dc-current-limit = <1300000>;
-			qcom,fast-charge-safe-voltage = <4400000>;
-			qcom,fast-charge-high-threshold-voltage = <4350000>;
-			qcom,fast-charge-low-threshold-voltage = <3400000>;
-			qcom,auto-recharge-threshold-voltage = <4200000>;
-			qcom,minimum-input-voltage = <4300000>;
-		};
-
-		gpios@c000 {
-			gpio_keys_pin_a: gpio-keys-active {
-				pins = "gpio2", "gpio3", "gpio4", "gpio5";
-				function = "normal";
-
-				bias-pull-up;
-				power-source = <PM8941_GPIO_S3>;
-			};
-		};
-
-		coincell@2800 {
-			status = "okay";
-			qcom,rset-ohms = <2100>;
-			qcom,vset-millivolts = <3000>;
-		};
-	};
-
-	pm8941@1 {
-		wled@d800 {
-			status = "okay";
-
-			qcom,cs-out;
-			qcom,current-limit = <20>;
-			qcom,current-boost-limit = <805>;
-			qcom,switching-freq = <1600>;
-			qcom,ovp = <29>;
-			qcom,num-strings = <2>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts
deleted file mode 100644
index e66937e3f7dd..000000000000
--- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts
+++ /dev/null
@@ -1,723 +0,0 @@
-#include "qcom-msm8974pro.dtsi"
-#include "qcom-pm8841.dtsi"
-#include "qcom-pm8941.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-
-/ {
-	model = "Sony Xperia Z2 Tablet";
-	compatible = "sony,xperia-castor", "qcom,msm8974";
-
-	aliases {
-		serial0 = &blsp1_uart2;
-		serial1 = &blsp2_uart7;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&gpio_keys_pin_a>;
-
-		volume-down {
-			label = "volume_down";
-			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEDOWN>;
-		};
-
-		camera-snapshot {
-			label = "camera_snapshot";
-			gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_CAMERA>;
-		};
-
-		camera-focus {
-			label = "camera_focus";
-			gpios = <&pm8941_gpios 4 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_CAMERA_FOCUS>;
-		};
-
-		volume-up {
-			label = "volume_up";
-			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEUP>;
-		};
-	};
-
-	smd {
-		rpm {
-			rpm_requests {
-				pm8941-regulators {
-					vdd_l1_l3-supply = <&pm8941_s1>;
-					vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
-					vdd_l4_l11-supply = <&pm8941_s1>;
-					vdd_l5_l7-supply = <&pm8941_s2>;
-					vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
-					vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
-					vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
-					vdd_l21-supply = <&vreg_boost>;
-
-					s1 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					s2 {
-						regulator-min-microvolt = <2150000>;
-						regulator-max-microvolt = <2150000>;
-						regulator-boot-on;
-					};
-
-					s3 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-						regulator-always-on;
-						regulator-boot-on;
-
-						regulator-system-load = <154000>;
-					};
-
-					s4 {
-						regulator-min-microvolt = <5000000>;
-						regulator-max-microvolt = <5000000>;
-					};
-
-					l1 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l2 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					l3 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					l4 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					l5 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l6 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l7 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l8 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l9 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					l11 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1350000>;
-					};
-
-					l12 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l13 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l14 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l15 {
-						regulator-min-microvolt = <2050000>;
-						regulator-max-microvolt = <2050000>;
-					};
-
-					l16 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l17 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l18 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					l19 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					l20 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-allow-set-load;
-						regulator-boot-on;
-						regulator-allow-set-load;
-						regulator-system-load = <500000>;
-					};
-
-					l21 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l22 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3000000>;
-					};
-
-					l23 {
-						regulator-min-microvolt = <2800000>;
-						regulator-max-microvolt = <2800000>;
-					};
-
-					l24 {
-						regulator-min-microvolt = <3075000>;
-						regulator-max-microvolt = <3075000>;
-
-						regulator-boot-on;
-					};
-				};
-			};
-		};
-	};
-
-	vreg_bl_vddio: lcd-backlight-vddio {
-		compatible = "regulator-fixed";
-		regulator-name = "vreg_bl_vddio";
-		regulator-min-microvolt = <3150000>;
-		regulator-max-microvolt = <3150000>;
-
-		gpio = <&msmgpio 69 0>;
-		enable-active-high;
-
-		vin-supply = <&pm8941_s3>;
-		startup-delay-us = <70000>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&lcd_backlight_en_pin_a>;
-	};
-
-	vreg_vsp: lcd-dcdc-regulator {
-		compatible = "regulator-fixed";
-		regulator-name = "vreg_vsp";
-		regulator-min-microvolt = <5600000>;
-		regulator-max-microvolt = <5600000>;
-
-		gpio = <&pm8941_gpios 20 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&lcd_dcdc_en_pin_a>;
-	};
-
-	vreg_wlan: wlan-regulator {
-		compatible = "regulator-fixed";
-
-		regulator-name = "wl-reg";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&pm8941_gpios 18 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&wlan_regulator_pin>;
-	};
-};
-
-&soc {
-	sdhci@f9824900 {
-		status = "okay";
-
-		vmmc-supply = <&pm8941_l20>;
-		vqmmc-supply = <&pm8941_s3>;
-
-		bus-width = <8>;
-		non-removable;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc1_pin_a>;
-	};
-
-	sdhci@f9864900 {
-		status = "okay";
-
-		max-frequency = <100000000>;
-		non-removable;
-		vmmc-supply = <&vreg_wlan>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc3_pin_a>;
-
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		bcrmf@1 {
-			compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac";
-			reg = <1>;
-
-			brcm,drive-strength = <10>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&wlan_sleep_clk_pin>;
-		};
-	};
-
-	sdhci@f98a4900 {
-		status = "okay";
-
-		bus-width = <4>;
-
-		vmmc-supply = <&pm8941_l21>;
-		vqmmc-supply = <&pm8941_l13>;
-
-		cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
-	};
-
-	serial@f991e000 {
-		status = "okay";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&blsp1_uart2_pin_a>;
-	};
-
-	serial@f995d000 {
-		status = "ok";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&blsp2_uart7_pin_a>;
-
-		bluetooth {
-			compatible = "brcm,bcm43438-bt";
-			max-speed = <3000000>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&bt_host_wake_pin>,
-				    <&bt_dev_wake_pin>,
-				    <&bt_reg_on_pin>;
-
-			host-wakeup-gpios = <&msmgpio 95 GPIO_ACTIVE_HIGH>;
-			device-wakeup-gpios = <&msmgpio 96 GPIO_ACTIVE_HIGH>;
-			shutdown-gpios = <&pm8941_gpios 16 GPIO_ACTIVE_HIGH>;
-		};
-	};
-
-	usb@f9a55000 {
-		status = "okay";
-
-		phys = <&usb_hs1_phy>;
-		phy-select = <&tcsr 0xb000 0>;
-		extcon = <&smbb>, <&usb_id>;
-		vbus-supply = <&chg_otg>;
-
-		hnp-disable;
-		srp-disable;
-		adp-disable;
-
-		ulpi {
-			phy@a {
-				status = "okay";
-
-				v1p8-supply = <&pm8941_l6>;
-				v3p3-supply = <&pm8941_l24>;
-
-				extcon = <&smbb>;
-				qcom,init-seq = /bits/ 8 <0x1 0x64>;
-			};
-		};
-	};
-
-	pinctrl@fd510000 {
-		blsp1_uart2_pin_a: blsp1-uart2-pin-active {
-			rx {
-				pins = "gpio5";
-				function = "blsp_uart2";
-
-				drive-strength = <2>;
-				bias-pull-up;
-			};
-
-			tx {
-				pins = "gpio4";
-				function = "blsp_uart2";
-
-				drive-strength = <4>;
-				bias-disable;
-			};
-		};
-
-		blsp2_uart7_pin_a: blsp2-uart7-pin-active {
-			tx {
-				pins = "gpio41";
-				function = "blsp_uart7";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-
-			rx {
-				pins = "gpio42";
-				function = "blsp_uart7";
-
-				drive-strength = <2>;
-				bias-pull-up;
-			};
-
-			cts {
-				pins = "gpio43";
-				function = "blsp_uart7";
-
-				drive-strength = <2>;
-				bias-pull-up;
-			};
-
-			rts {
-				pins = "gpio44";
-				function = "blsp_uart7";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		i2c8_pins: i2c8 {
-			mux {
-				pins = "gpio47", "gpio48";
-				function = "blsp_i2c8";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		i2c11_pins: i2c11 {
-			mux {
-				pins = "gpio83", "gpio84";
-				function = "blsp_i2c11";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		lcd_backlight_en_pin_a: lcd-backlight-vddio {
-			pins = "gpio69";
-			drive-strength = <10>;
-			output-low;
-			bias-disable;
-		};
-
-		sdhc1_pin_a: sdhc1-pin-active {
-			clk {
-				pins = "sdc1_clk";
-				drive-strength = <16>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc1_cmd", "sdc1_data";
-				drive-strength = <10>;
-				bias-pull-up;
-			};
-		};
-
-		sdhc2_cd_pin_a: sdhc2-cd-pin-active {
-			pins = "gpio62";
-			function = "gpio";
-
-			drive-strength = <2>;
-			bias-disable;
-		 };
-
-		sdhc2_pin_a: sdhc2-pin-active {
-			clk {
-				pins = "sdc2_clk";
-				drive-strength = <6>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc2_cmd", "sdc2_data";
-				drive-strength = <6>;
-				bias-pull-up;
-			};
-		};
-
-		sdhc3_pin_a: sdhc3-pin-active {
-			clk {
-				pins = "gpio40";
-				function = "sdc3";
-
-				drive-strength = <10>;
-				bias-disable;
-			};
-
-			cmd {
-				pins = "gpio39";
-				function = "sdc3";
-
-				drive-strength = <10>;
-				bias-pull-up;
-			};
-
-			data {
-				pins = "gpio35", "gpio36", "gpio37", "gpio38";
-				function = "sdc3";
-
-				drive-strength = <10>;
-				bias-pull-up;
-			};
-		};
-
-		ts_int_pin: synaptics {
-			pin {
-				pins = "gpio86";
-				function = "gpio";
-
-				drive-strength = <2>;
-				bias-disable;
-				input-enable;
-			};
-		};
-
-		bt_host_wake_pin: bt-host-wake {
-			pins = "gpio95";
-			function = "gpio";
-
-			drive-strength = <2>;
-			bias-disable;
-			output-low;
-		};
-
-		bt_dev_wake_pin: bt-dev-wake {
-			pins = "gpio96";
-			function = "gpio";
-
-			drive-strength = <2>;
-			bias-disable;
-		};
-	};
-
-	i2c@f9964000 {
-		status = "okay";
-
-		clock-frequency = <355000>;
-		qcom,src-freq = <50000000>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c8_pins>;
-
-		synaptics@2c {
-			compatible = "syna,rmi4-i2c";
-			reg = <0x2c>;
-
-			interrupt-parent = <&msmgpio>;
-			interrupts = <86 IRQ_TYPE_EDGE_FALLING>;
-
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			vdd-supply = <&pm8941_l22>;
-			vio-supply = <&pm8941_lvs3>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&ts_int_pin>;
-
-			syna,startup-delay-ms = <10>;
-
-			rmi-f01@1 {
-				reg = <0x1>;
-				syna,nosleep = <1>;
-			};
-
-			rmi-f11@11 {
-				reg = <0x11>;
-				syna,f11-flip-x = <1>;
-				syna,sensor-type = <1>;
-			};
-		};
-	};
-
-	i2c@f9967000 {
-		status = "okay";
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c11_pins>;
-		clock-frequency = <355000>;
-		qcom,src-freq = <50000000>;
-
-		lp8566_wled: backlight@2c {
-			compatible = "ti,lp8556";
-			reg = <0x2c>;
-			power-supply = <&vreg_bl_vddio>;
-
-			bl-name = "backlight";
-			dev-ctrl = /bits/ 8 <0x05>;
-			init-brt = /bits/ 8 <0x3f>;
-			rom_a0h {
-				rom-addr = /bits/ 8 <0xa0>;
-				rom-val = /bits/ 8 <0xff>;
-			};
-			rom_a1h {
-				rom-addr = /bits/ 8 <0xa1>;
-				rom-val = /bits/ 8 <0x3f>;
-			};
-			rom_a2h {
-				rom-addr = /bits/ 8 <0xa2>;
-				rom-val = /bits/ 8 <0x20>;
-			};
-			rom_a3h {
-				rom-addr = /bits/ 8 <0xa3>;
-				rom-val = /bits/ 8 <0x5e>;
-			};
-			rom_a4h {
-				rom-addr = /bits/ 8 <0xa4>;
-				rom-val = /bits/ 8 <0x02>;
-			};
-			rom_a5h {
-				rom-addr = /bits/ 8 <0xa5>;
-				rom-val = /bits/ 8 <0x04>;
-			};
-			rom_a6h {
-				rom-addr = /bits/ 8 <0xa6>;
-				rom-val = /bits/ 8 <0x80>;
-			};
-			rom_a7h {
-				rom-addr = /bits/ 8 <0xa7>;
-				rom-val = /bits/ 8 <0xf7>;
-			};
-			rom_a9h {
-				rom-addr = /bits/ 8 <0xa9>;
-				rom-val = /bits/ 8 <0x80>;
-			};
-			rom_aah {
-				rom-addr = /bits/ 8 <0xaa>;
-				rom-val = /bits/ 8 <0x0f>;
-			};
-			rom_aeh {
-				rom-addr = /bits/ 8 <0xae>;
-				rom-val = /bits/ 8 <0x0f>;
-			};
-		};
-	};
-};
-
-&spmi_bus {
-	pm8941@0 {
-		charger@1000 {
-			qcom,fast-charge-safe-current = <1500000>;
-			qcom,fast-charge-current-limit = <1500000>;
-			qcom,dc-current-limit = <1800000>;
-			qcom,fast-charge-safe-voltage = <4400000>;
-			qcom,fast-charge-high-threshold-voltage = <4350000>;
-			qcom,fast-charge-low-threshold-voltage = <3400000>;
-			qcom,auto-recharge-threshold-voltage = <4200000>;
-			qcom,minimum-input-voltage = <4300000>;
-		};
-
-		gpios@c000 {
-			gpio_keys_pin_a: gpio-keys-active {
-				pins = "gpio2", "gpio5";
-				function = "normal";
-
-				bias-pull-up;
-				power-source = <PM8941_GPIO_S3>;
-			};
-
-			bt_reg_on_pin: bt-reg-on {
-				pins = "gpio16";
-				function = "normal";
-
-				output-low;
-				power-source = <PM8941_GPIO_S3>;
-			};
-
-			wlan_sleep_clk_pin: wl-sleep-clk {
-				pins = "gpio17";
-				function = "func2";
-
-				output-high;
-				power-source = <PM8941_GPIO_S3>;
-			};
-
-			wlan_regulator_pin: wl-reg-active {
-				pins = "gpio18";
-				function = "normal";
-
-				bias-disable;
-				power-source = <PM8941_GPIO_S3>;
-			};
-
-			lcd_dcdc_en_pin_a: lcd-dcdc-en-active {
-				pins = "gpio20";
-				function = "normal";
-
-				bias-disable;
-				power-source = <PM8941_GPIO_S3>;
-				input-disable;
-				output-low;
-			};
-
-		};
-
-		coincell@2800 {
-			status = "okay";
-			qcom,rset-ohms = <2100>;
-			qcom,vset-millivolts = <3000>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts
deleted file mode 100644
index a62e5c25b23c..000000000000
--- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts
+++ /dev/null
@@ -1,484 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-msm8974.dtsi"
-#include "qcom-pm8841.dtsi"
-#include "qcom-pm8941.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-
-/ {
-	model = "Sony Xperia Z1";
-	compatible = "sony,xperia-honami", "qcom,msm8974";
-
-	aliases {
-		serial0 = &blsp1_uart2;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&gpio_keys_pin_a>;
-
-		volume-down {
-			label = "volume_down";
-			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEDOWN>;
-		};
-
-		camera-snapshot {
-			label = "camera_snapshot";
-			gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_CAMERA>;
-		};
-
-		camera-focus {
-			label = "camera_focus";
-			gpios = <&pm8941_gpios 4 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_CAMERA_FOCUS>;
-		};
-
-		volume-up {
-			label = "volume_up";
-			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEUP>;
-		};
-	};
-
-	memory@0 {
-		reg = <0 0x40000000>, <0x40000000 0x40000000>;
-		device_type = "memory";
-	};
-
-	smd {
-		rpm {
-			rpm_requests {
-				pm8841-regulators {
-					s1 {
-						regulator-min-microvolt = <675000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s2 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s3 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s4 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-				};
-
-				pm8941-regulators {
-					vdd_l1_l3-supply = <&pm8941_s1>;
-					vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
-					vdd_l4_l11-supply = <&pm8941_s1>;
-					vdd_l5_l7-supply = <&pm8941_s2>;
-					vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
-					vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
-					vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
-					vdd_l21-supply = <&vreg_boost>;
-
-					s1 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					s2 {
-						regulator-min-microvolt = <2150000>;
-						regulator-max-microvolt = <2150000>;
-						regulator-boot-on;
-					};
-
-					s3 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					s4 {
-						regulator-min-microvolt = <5000000>;
-						regulator-max-microvolt = <5000000>;
-					};
-
-					l1 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l2 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					l3 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					l4 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					l5 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l6 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l7 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l8 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l9 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					l11 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1350000>;
-					};
-
-					l12 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l13 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l14 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l15 {
-						regulator-min-microvolt = <2050000>;
-						regulator-max-microvolt = <2050000>;
-					};
-
-					l16 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l17 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l18 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					l19 {
-						regulator-min-microvolt = <3300000>;
-						regulator-max-microvolt = <3300000>;
-					};
-
-					l20 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-allow-set-load;
-						regulator-boot-on;
-						regulator-system-load = <200000>;
-					};
-
-					l21 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l22 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3000000>;
-					};
-
-					l23 {
-						regulator-min-microvolt = <2800000>;
-						regulator-max-microvolt = <2800000>;
-					};
-
-					l24 {
-						regulator-min-microvolt = <3075000>;
-						regulator-max-microvolt = <3075000>;
-
-						regulator-boot-on;
-					};
-				};
-			};
-		};
-	};
-};
-
-&soc {
-	usb@f9a55000 {
-		status = "okay";
-
-		phys = <&usb_hs1_phy>;
-		phy-select = <&tcsr 0xb000 0>;
-		extcon = <&smbb>, <&usb_id>;
-		vbus-supply = <&chg_otg>;
-
-		hnp-disable;
-		srp-disable;
-		adp-disable;
-
-		ulpi {
-			phy@a {
-				status = "okay";
-
-				v1p8-supply = <&pm8941_l6>;
-				v3p3-supply = <&pm8941_l24>;
-
-				extcon = <&smbb>;
-				qcom,init-seq = /bits/ 8 <0x1 0x64>;
-			};
-		};
-	};
-
-	sdhci@f9824900 {
-		status = "okay";
-
-		vmmc-supply = <&pm8941_l20>;
-		vqmmc-supply = <&pm8941_s3>;
-
-		bus-width = <8>;
-		non-removable;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc1_pin_a>;
-	};
-
-	sdhci@f98a4900 {
-		status = "okay";
-
-		bus-width = <4>;
-
-		vmmc-supply = <&pm8941_l21>;
-		vqmmc-supply = <&pm8941_l13>;
-
-		cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
-	};
-
-	serial@f991e000 {
-		status = "okay";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&blsp1_uart2_pin_a>;
-	};
-
-	i2c@f9924000 {
-		status = "okay";
-
-		clock-frequency = <355000>;
-		qcom,src-freq = <50000000>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c2_pins>;
-
-		synaptics@2c {
-			compatible = "syna,rmi4-i2c";
-			reg = <0x2c>;
-
-			interrupts-extended = <&msmgpio 61 IRQ_TYPE_EDGE_FALLING>;
-
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			vdd-supply = <&pm8941_l22>;
-			vio-supply = <&pm8941_lvs3>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&ts_int_pin>;
-
-			syna,startup-delay-ms = <10>;
-
-			rmi4-f01@1 {
-				reg = <0x1>;
-				syna,nosleep-mode = <1>;
-			};
-
-			rmi4-f11@11 {
-				reg = <0x11>;
-				touchscreen-inverted-x;
-				syna,sensor-type = <1>;
-			};
-		};
-	};
-
-	pinctrl@fd510000 {
-		blsp1_uart2_pin_a: blsp1-uart2-pin-active {
-			rx {
-				pins = "gpio5";
-				function = "blsp_uart2";
-
-				drive-strength = <2>;
-				bias-pull-up;
-			};
-
-			tx {
-				pins = "gpio4";
-				function = "blsp_uart2";
-
-				drive-strength = <4>;
-				bias-disable;
-			};
-		};
-
-		i2c2_pins: i2c2 {
-			mux {
-				pins = "gpio6", "gpio7";
-				function = "blsp_i2c2";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		sdhc1_pin_a: sdhc1-pin-active {
-			clk {
-				pins = "sdc1_clk";
-				drive-strength = <16>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc1_cmd", "sdc1_data";
-				drive-strength = <10>;
-				bias-pull-up;
-			};
-		};
-
-		sdhc2_cd_pin_a: sdhc2-cd-pin-active {
-			pins = "gpio62";
-			function = "gpio";
-
-			drive-strength = <2>;
-			bias-disable;
-		 };
-
-		sdhc2_pin_a: sdhc2-pin-active {
-			clk {
-				pins = "sdc2_clk";
-				drive-strength = <10>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc2_cmd", "sdc2_data";
-				drive-strength = <6>;
-				bias-pull-up;
-			};
-		};
-
-		ts_int_pin: touch-int {
-			pin {
-				pins = "gpio61";
-				function = "gpio";
-
-				drive-strength = <2>;
-				bias-disable;
-				input-enable;
-			};
-		};
-	};
-
-	dma-controller@f9944000 {
-		qcom,controlled-remotely;
-	};
-};
-
-&spmi_bus {
-	pm8941@0 {
-		charger@1000 {
-			qcom,fast-charge-safe-current = <1500000>;
-			qcom,fast-charge-current-limit = <1500000>;
-			qcom,dc-current-limit = <1800000>;
-			qcom,fast-charge-safe-voltage = <4400000>;
-			qcom,fast-charge-high-threshold-voltage = <4350000>;
-			qcom,fast-charge-low-threshold-voltage = <3400000>;
-			qcom,auto-recharge-threshold-voltage = <4200000>;
-			qcom,minimum-input-voltage = <4300000>;
-		};
-
-		gpios@c000 {
-			gpio_keys_pin_a: gpio-keys-active {
-				pins = "gpio2", "gpio3", "gpio4", "gpio5";
-				function = "normal";
-
-				bias-pull-up;
-				power-source = <PM8941_GPIO_S3>;
-			};
-		};
-
-		coincell@2800 {
-			status = "okay";
-			qcom,rset-ohms = <2100>;
-			qcom,vset-millivolts = <3000>;
-		};
-	};
-
-	pm8941@1 {
-		wled@d800 {
-			status = "okay";
-
-			qcom,cs-out;
-			qcom,current-limit = <20>;
-			qcom,current-boost-limit = <805>;
-			qcom,switching-freq = <1600>;
-			qcom,ovp = <29>;
-			qcom,num-strings = <2>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-msm8974pro.dtsi b/arch/arm/boot/dts/qcom-msm8974pro.dtsi
deleted file mode 100644
index b64c28036dd0..000000000000
--- a/arch/arm/boot/dts/qcom-msm8974pro.dtsi
+++ /dev/null
@@ -1,23 +0,0 @@
-#include "qcom-msm8974.dtsi"
-
-/ {
-	soc {
-		sdhci@f9824900 {
-			clocks = <&gcc GCC_SDCC1_APPS_CLK>,
-				 <&gcc GCC_SDCC1_AHB_CLK>,
-				 <&xo_board>,
-				 <&gcc GCC_SDCC1_CDCCAL_FF_CLK>,
-				 <&gcc GCC_SDCC1_CDCCAL_SLEEP_CLK>;
-			clock-names = "core", "iface", "xo", "cal", "sleep";
-		};
-
-		clock-controller@fc400000 {
-				compatible = "qcom,gcc-msm8974pro";
-		};
-
-		adreno@fdb00000 {
-			compatible = "qcom,adreno-330.2",
-				     "qcom,adreno";
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-pm8226.dtsi b/arch/arm/boot/dts/qcom-pm8226.dtsi
deleted file mode 100644
index b3d0f7b5874d..000000000000
--- a/arch/arm/boot/dts/qcom-pm8226.dtsi
+++ /dev/null
@@ -1,70 +0,0 @@
-// SPDX-License-Identifier: BSD-3-Clause
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/spmi/spmi.h>
-
-&spmi_bus {
-	pm8226_0: pm8226@0 {
-		compatible = "qcom,pm8226", "qcom,spmi-pmic";
-		reg = <0x0 SPMI_USID>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		pwrkey@800 {
-			compatible = "qcom,pm8941-pwrkey";
-			reg = <0x800>;
-			interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
-			debounce = <15625>;
-			bias-pull-up;
-		};
-
-		smbb: charger@1000 {
-			compatible = "qcom,pm8226-charger";
-			reg = <0x1000>;
-			interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
-				     <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>,
-				     <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>,
-				     <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>,
-				     <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>,
-				     <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>,
-				     <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>,
-				     <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>;
-			interrupt-names = "chg-done",
-					  "chg-fast",
-					  "chg-trkl",
-					  "bat-temp-ok",
-					  "bat-present",
-					  "chg-gone",
-					  "usb-valid",
-					  "dc-valid";
-
-			chg_otg: otg-vbus { };
-		};
-
-		pm8226_mpps: mpps@a000 {
-			compatible = "qcom,pm8226-mpp", "qcom,spmi-mpp";
-			reg = <0xa000>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			gpio-ranges = <&pm8226_mpps 0 0 8>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-	};
-
-	pm8226_1: pm8226@1 {
-		compatible = "qcom,pm8226", "qcom,spmi-pmic";
-		reg = <0x1 SPMI_USID>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		pm8226_spmi_regulators: pm8226-regulators {
-			compatible = "qcom,pm8226-regulators";
-		};
-
-		pm8226_vib: vibrator@c000 {
-			compatible = "qcom,pm8916-vib";
-			reg = <0xc000>;
-			status = "disabled";
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-sdx65-mtp.dts b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
deleted file mode 100644
index 59457da8e5f1..000000000000
--- a/arch/arm/boot/dts/qcom-sdx65-mtp.dts
+++ /dev/null
@@ -1,25 +0,0 @@
-// SPDX-License-Identifier: BSD-3-Clause
-/*
- * Copyright (c) 2021 Qualcomm Innovation Center, Inc. All rights reserved.
- */
-/dts-v1/;
-
-#include "qcom-sdx65.dtsi"
-
-/ {
-	model = "Qualcomm Technologies, Inc. SDX65 MTP";
-	compatible = "qcom,sdx65-mtp", "qcom,sdx65";
-	qcom,board-id = <0x2010008 0x302>;
-
-	aliases {
-		serial0 = &blsp1_uart3;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-};
-
-&blsp1_uart3 {
-	status = "ok";
-};
diff --git a/arch/arm/boot/dts/qcom-sdx65.dtsi b/arch/arm/boot/dts/qcom-sdx65.dtsi
deleted file mode 100644
index 796641d30e06..000000000000
--- a/arch/arm/boot/dts/qcom-sdx65.dtsi
+++ /dev/null
@@ -1,222 +0,0 @@
-// SPDX-License-Identifier: BSD-3-Clause
-/*
- * SDX65 SoC device tree source
- *
- * Copyright (c) 2021 Qualcomm Innovation Center, Inc. All rights reserved.
- *
- */
-
-#include <dt-bindings/clock/qcom,gcc-sdx65.h>
-#include <dt-bindings/clock/qcom,rpmh.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/soc/qcom,rpmh-rsc.h>
-
-/ {
-	#address-cells = <1>;
-	#size-cells = <1>;
-	qcom,msm-id = <458 0x10000>, <483 0x10000>, <509 0x10000>;
-	interrupt-parent = <&intc>;
-
-	memory {
-		device_type = "memory";
-		reg = <0 0>;
-	};
-
-	clocks {
-		xo_board: xo-board {
-			compatible = "fixed-clock";
-			clock-frequency = <76800000>;
-			clock-output-names = "xo_board";
-			#clock-cells = <0>;
-		};
-
-		sleep_clk: sleep-clk {
-			compatible = "fixed-clock";
-			clock-frequency = <32764>;
-			clock-output-names = "sleep_clk";
-			#clock-cells = <0>;
-		};
-	};
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu0: cpu@0 {
-			device_type = "cpu";
-			compatible = "arm,cortex-a7";
-			reg = <0x0>;
-			enable-method = "psci";
-		};
-	};
-
-	psci {
-		compatible = "arm,psci-1.0";
-		method = "smc";
-	};
-
-	reserved_memory: reserved-memory {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		cmd_db: reserved-memory@8fee0000 {
-			compatible = "qcom,cmd-db";
-			reg = <0x8fee0000 0x20000>;
-			no-map;
-		};
-	};
-
-	soc: soc {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-		compatible = "simple-bus";
-
-		gcc: clock-controller@100000 {
-			compatible = "qcom,gcc-sdx65";
-			reg = <0x00100000 0x001f7400>;
-			clocks = <&rpmhcc RPMH_CXO_CLK>, <&rpmhcc RPMH_CXO_CLK_A>, <&sleep_clk>;
-			clock-names = "bi_tcxo", "bi_tcxo_ao", "sleep_clk";
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-		};
-
-		blsp1_uart3: serial@831000 {
-			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
-			reg = <0x00831000 0x200>;
-			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
-			clock-names = "core", "iface";
-			status = "disabled";
-		};
-
-		tlmm: pinctrl@f100000 {
-			compatible = "qcom,sdx65-tlmm";
-			reg = <0xf100000 0x300000>;
-			interrupts = <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>;
-			gpio-controller;
-			#gpio-cells = <2>;
-			gpio-ranges = <&tlmm 0 0 109>;
-			interrupt-controller;
-			interrupt-parent = <&intc>;
-			#interrupt-cells = <2>;
-		};
-
-		pdc: interrupt-controller@b210000 {
-			compatible = "qcom,sdx65-pdc", "qcom,pdc";
-			reg = <0xb210000 0x10000>;
-			qcom,pdc-ranges = <0 147 52>, <52 266 32>;
-			#interrupt-cells = <2>;
-			interrupt-parent = <&intc>;
-			interrupt-controller;
-		};
-
-		intc: interrupt-controller@17800000 {
-			compatible = "qcom,msm-qgic2";
-			interrupt-controller;
-			interrupt-parent = <&intc>;
-			#interrupt-cells = <3>;
-			reg = <0x17800000 0x1000>,
-			      <0x17802000 0x1000>;
-		};
-
-		timer@17820000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-			compatible = "arm,armv7-timer-mem";
-			reg = <0x17820000 0x1000>;
-			clock-frequency = <19200000>;
-
-			frame@17821000 {
-				frame-number = <0>;
-				interrupts = <GIC_SPI 7 0x4>,
-					     <GIC_SPI 6 0x4>;
-				reg = <0x17821000 0x1000>,
-				      <0x17822000 0x1000>;
-			};
-
-			frame@17823000 {
-				frame-number = <1>;
-				interrupts = <GIC_SPI 8 0x4>;
-				reg = <0x17823000 0x1000>;
-				status = "disabled";
-			};
-
-			frame@17824000 {
-				frame-number = <2>;
-				interrupts = <GIC_SPI 9 0x4>;
-				reg = <0x17824000 0x1000>;
-				status = "disabled";
-			};
-
-			frame@17825000 {
-				frame-number = <3>;
-				interrupts = <GIC_SPI 10 0x4>;
-				reg = <0x17825000 0x1000>;
-				status = "disabled";
-			};
-
-			frame@17826000 {
-				frame-number = <4>;
-				interrupts = <GIC_SPI 11 0x4>;
-				reg = <0x17826000 0x1000>;
-				status = "disabled";
-			};
-
-			frame@17827000 {
-				frame-number = <5>;
-				interrupts = <GIC_SPI 12 0x4>;
-				reg = <0x17827000 0x1000>;
-				status = "disabled";
-			};
-
-			frame@17828000 {
-				frame-number = <6>;
-				interrupts = <GIC_SPI 13 0x4>;
-				reg = <0x17828000 0x1000>;
-				status = "disabled";
-			};
-
-			frame@17829000 {
-				frame-number = <7>;
-				interrupts = <GIC_SPI 14 0x4>;
-				reg = <0x17829000 0x1000>;
-				status = "disabled";
-			};
-		};
-
-		apps_rsc: rsc@17830000 {
-			label = "apps_rsc";
-			compatible = "qcom,rpmh-rsc";
-			reg = <0x17830000 0x10000>,
-			    <0x17840000 0x10000>;
-			reg-names = "drv-0", "drv-1";
-			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
-				   <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
-			qcom,tcs-offset = <0xd00>;
-			qcom,drv-id = <1>;
-			qcom,tcs-config = <ACTIVE_TCS  2>,
-				<SLEEP_TCS   2>,
-				<WAKE_TCS    2>,
-				<CONTROL_TCS 1>;
-
-			rpmhcc: clock-controller@1 {
-				compatible = "qcom,sdx65-rpmh-clk";
-				#clock-cells = <1>;
-				clock-names = "xo";
-				clocks = <&xo_board>;
-			};
-		};
-	};
-
-	timer {
-		compatible = "arm,armv7-timer";
-		interrupts = <1 13 0xf08>,
-			<1 12 0xf08>,
-			<1 10 0xf08>,
-			<1 11 0xf08>;
-		clock-frequency = <19200000>;
-	};
-};
diff --git a/arch/arm/boot/dts/qcom/Makefile b/arch/arm/boot/dts/qcom/Makefile
new file mode 100644
index 000000000000..c7873dcef154
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/Makefile
@@ -0,0 +1,64 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_QCOM) += \
+	msm8226-motorola-falcon.dtb \
+	qcom-apq8016-sbc.dtb \
+	qcom-apq8026-asus-sparrow.dtb \
+	qcom-apq8026-huawei-sturgeon.dtb \
+	qcom-apq8026-lg-lenok.dtb \
+	qcom-apq8026-samsung-matisse-wifi.dtb \
+	qcom-apq8026-samsung-milletwifi.dtb \
+	qcom-apq8060-dragonboard.dtb \
+	qcom-apq8064-cm-qs600.dtb \
+	qcom-apq8064-ifc6410.dtb \
+	qcom-apq8064-sony-xperia-lagan-yuga.dtb \
+	qcom-apq8064-asus-nexus7-flo.dtb \
+	qcom-apq8064-lg-nexus4-mako.dtb \
+	qcom-apq8074-dragonboard.dtb \
+	qcom-apq8084-ifc6540.dtb \
+	qcom-apq8084-mtp.dtb \
+	qcom-ipq4018-ap120c-ac.dtb \
+	qcom-ipq4018-ap120c-ac-bit.dtb \
+	qcom-ipq4018-jalapeno.dtb \
+	qcom-ipq4019-ap.dk01.1-c1.dtb \
+	qcom-ipq4019-ap.dk04.1-c1.dtb \
+	qcom-ipq4019-ap.dk04.1-c3.dtb \
+	qcom-ipq4019-ap.dk07.1-c1.dtb \
+	qcom-ipq4019-ap.dk07.1-c2.dtb \
+	qcom-ipq8064-ap148.dtb \
+	qcom-ipq8064-rb3011.dtb \
+	qcom-msm8226-microsoft-dempsey.dtb \
+	qcom-msm8226-microsoft-makepeace.dtb \
+	qcom-msm8226-microsoft-moneypenny.dtb \
+	qcom-msm8226-samsung-ms013g.dtb \
+	qcom-msm8226-samsung-s3ve3g.dtb \
+	qcom-msm8660-surf.dtb \
+	qcom-msm8916-samsung-e5.dtb \
+	qcom-msm8916-samsung-e7.dtb \
+	qcom-msm8916-samsung-grandmax.dtb \
+	qcom-msm8916-samsung-serranove.dtb \
+	qcom-msm8926-htc-memul.dtb \
+	qcom-msm8926-microsoft-superman-lte.dtb \
+	qcom-msm8926-microsoft-tesla.dtb \
+	qcom-msm8926-motorola-peregrine.dtb \
+	qcom-msm8926-samsung-matisselte.dtb \
+	qcom-msm8960-cdp.dtb \
+	qcom-msm8960-samsung-expressatt.dtb \
+	qcom-msm8960-sony-huashan.dtb \
+	qcom-msm8974-lge-nexus5-hammerhead.dtb \
+	qcom-msm8974-samsung-hlte.dtb \
+	qcom-msm8974-sony-xperia-rhine-amami.dtb \
+	qcom-msm8974-sony-xperia-rhine-honami.dtb \
+	qcom-msm8974-sony-xperia-rhine-togari.dtb \
+	qcom-msm8974pro-fairphone-fp2.dtb \
+	qcom-msm8974pro-htc-m8.dtb \
+	qcom-msm8974pro-oneplus-bacon.dtb \
+	qcom-msm8974pro-samsung-klte.dtb \
+	qcom-msm8974pro-samsung-kltechn.dtb \
+	qcom-msm8974pro-sony-xperia-shinano-aries.dtb \
+	qcom-msm8974pro-sony-xperia-shinano-castor.dtb \
+	qcom-msm8974pro-sony-xperia-shinano-leo.dtb \
+	qcom-mdm9615-wp8548-mangoh-green.dtb \
+	qcom-sdx55-mtp.dtb \
+	qcom-sdx55-t55.dtb \
+	qcom-sdx55-telit-fn980-tlb.dtb \
+	qcom-sdx65-mtp.dtb
diff --git a/arch/arm/boot/dts/qcom/msm8226-motorola-falcon.dts b/arch/arm/boot/dts/qcom/msm8226-motorola-falcon.dts
new file mode 100644
index 000000000000..e6392f7d14c7
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/msm8226-motorola-falcon.dts
@@ -0,0 +1,426 @@
+// SPDX-License-Identifier: BSD-3-Clause
+
+/dts-v1/;
+
+#include "qcom-msm8226.dtsi"
+#include "pm8226.dtsi"
+
+/delete-node/ &smem_region;
+
+/ {
+	model = "Motorola Moto G (2013)";
+	compatible = "motorola,falcon", "qcom,msm8226";
+	chassis-type = "handset";
+
+	aliases {
+		mmc0 = &sdhc_1;
+	};
+
+	chosen {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		framebuffer@3200000 {
+			compatible = "simple-framebuffer";
+			reg = <0x03200000 0x800000>;
+			width = <720>;
+			height = <1280>;
+			stride = <(720 * 3)>;
+			format = "r8g8b8";
+			vsp-supply = <&reg_lcd_pos>;
+			vsn-supply = <&reg_lcd_neg>;
+			vddio-supply = <&vddio_disp_vreg>;
+			clocks = <&mmcc MDSS_AHB_CLK>,
+				 <&mmcc MDSS_AXI_CLK>,
+				 <&mmcc MDSS_BYTE0_CLK>,
+				 <&mmcc MDSS_ESC0_CLK>,
+				 <&mmcc MDSS_MDP_CLK>,
+				 <&mmcc MMSS_MISC_AHB_CLK>,
+				 <&mmcc MDSS_PCLK0_CLK>,
+				 <&mmcc MDSS_VSYNC_CLK>;
+			power-domains = <&mmcc MDSS_GDSC>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		event-hall-sensor {
+			label = "Hall Effect Sensor";
+			gpios = <&tlmm 51 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			linux,can-disable;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <15>;
+		};
+	};
+
+	/* TI TPS22902 */
+	vddio_disp_vreg: regulator-vddio-disp {
+		compatible = "regulator-fixed";
+		regulator-name = "vddio_disp";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&tlmm 34 GPIO_ACTIVE_HIGH>;
+		vin-supply = <&pm8226_l8>;
+		startup-delay-us = <300>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		framebuffer@3200000 {
+			reg = <0x03200000 0x800000>;
+			no-map;
+		};
+
+		dhob@f500000 {
+			reg = <0x0f500000 0x40000>;
+			no-map;
+		};
+
+		shob@f540000 {
+			reg = <0x0f540000 0x2000>;
+			no-map;
+		};
+
+		smem_region: smem@fa00000 {
+			reg = <0x0fa00000 0x100000>;
+			no-map;
+		};
+
+		/* Actually <0x0fa00000 0x500000>, but first 100000 is smem */
+		reserved@fb00000 {
+			reg = <0x0fb00000 0x400000>;
+			no-map;
+		};
+	};
+};
+
+&blsp1_i2c2 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	magnetometer@c {
+		compatible = "asahi-kasei,ak8963";
+		reg = <0xc>;
+		interrupts-extended = <&tlmm 66 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
+		vdd-supply = <&pm8226_l19>;
+		vid-supply = <&pm8226_lvs1>;
+		pinctrl-0 = <&mag_int_default &mag_reset_default>;
+		pinctrl-names = "default";
+	};
+
+	accelerometer@19 {
+		compatible = "st,lis3dh-accel";
+		reg = <0x19>;
+		interrupts-extended = <&tlmm 63 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8226_l19>;
+		vddio-supply = <&pm8226_lvs1>;
+		pinctrl-0 = <&accel_int_default>;
+		pinctrl-names = "default";
+		mount-matrix = "0", "1", "0",
+			       "1", "0", "0",
+			       "0", "0", "-1";
+		st,drdy-int-pin = <1>;
+	};
+};
+
+&blsp1_i2c3 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	regulator@3e {
+		compatible = "ti,tps65132";
+		reg = <0x3e>;
+		pinctrl-0 = <&reg_lcd_default>;
+		pinctrl-names = "default";
+
+		reg_lcd_pos: outp {
+			regulator-name = "outp";
+			regulator-min-microvolt = <5400000>;
+			regulator-max-microvolt = <5400000>;
+			regulator-active-discharge = <1>;
+			regulator-boot-on;
+			enable-gpios = <&tlmm 31 GPIO_ACTIVE_HIGH>;
+		};
+
+		reg_lcd_neg: outn {
+			regulator-name = "outn";
+			regulator-min-microvolt = <5400000>;
+			regulator-max-microvolt = <5400000>;
+			regulator-active-discharge = <1>;
+			regulator-boot-on;
+			enable-gpios = <&tlmm 33 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	temperature-sensor@48 {
+		compatible = "ti,tmp108";
+		reg = <0x48>;
+		interrupts-extended = <&tlmm 13 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-0 = <&temp_alert_default>;
+		pinctrl-names = "default";
+		#thermal-sensor-cells = <0>;
+	};
+};
+
+&pm8226_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+	status = "okay";
+};
+
+&pm8226_vib {
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-pm8226-regulators";
+
+		pm8226_s3: s3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8226_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2200000>;
+		};
+
+		pm8226_s5: s5 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8226_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l3: l3 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1337500>;
+		};
+
+		pm8226_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l5: l5 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-allow-set-load;
+		};
+
+		pm8226_l7: l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <1850000>;
+		};
+
+		pm8226_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l9: l9 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l14: l14 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+		};
+
+		pm8226_l15: l15 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+
+		pm8226_l16: l16 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3350000>;
+		};
+
+		pm8226_l17: l17 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l18: l18 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l19: l19 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8226_l20: l20 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+
+		pm8226_l21: l21 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-allow-set-load;
+		};
+
+		pm8226_l22: l22 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l24: l24 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8226_l25: l25 {
+			regulator-min-microvolt = <1775000>;
+			regulator-max-microvolt = <2125000>;
+		};
+
+		pm8226_l26: l26 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8226_l27: l27 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l28: l28 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3400000>;
+			regulator-boot-on;
+		};
+
+		pm8226_lvs1: lvs1 {
+			regulator-always-on;
+		};
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&pm8226_l17>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	bus-width = <8>;
+	non-removable;
+
+	status = "okay";
+};
+
+&smbb {
+	qcom,fast-charge-safe-current = <2000000>;
+	qcom,fast-charge-current-limit = <1900000>;
+	qcom,fast-charge-safe-voltage = <4400000>;
+	qcom,minimum-input-voltage = <4300000>;
+
+	status = "okay";
+};
+
+&tlmm {
+	accel_int_default: accel-int-default-state {
+		pins = "gpio63";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-disable;
+	};
+
+	mag_int_default: mag-int-default-state {
+		pins = "gpio66";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-disable;
+	};
+
+	mag_reset_default: mag-reset-default-state {
+		pins = "gpio62";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-high;
+	};
+
+	reg_lcd_default: reg-lcd-default-state {
+		pins = "gpio31", "gpio33";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-high;
+	};
+
+	reg_vddio_disp_default: reg-vddio-disp-default-state {
+		pins = "gpio34";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-high;
+	};
+
+	temp_alert_default: temp-alert-default-state {
+		pins = "gpio13";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-disable;
+	};
+};
+
+&usb {
+	extcon = <&smbb>;
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usb_hs_phy {
+	extcon = <&smbb>;
+	v1p8-supply = <&pm8226_l10>;
+	v3p3-supply = <&pm8226_l20>;
+};
diff --git a/arch/arm/boot/dts/qcom/msm8926.dtsi b/arch/arm/boot/dts/qcom/msm8926.dtsi
new file mode 100644
index 000000000000..629654c525b4
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/msm8926.dtsi
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2025, Luca Weiss <luca@lucaweiss.eu>
+ */
+
+#include "qcom-msm8226.dtsi"
+
+&modem {
+	compatible = "qcom,msm8926-mss-pil";
+	/delete-property/ qcom,ext-bhs-reg;
+};
diff --git a/arch/arm/boot/dts/qcom/pm8018.dtsi b/arch/arm/boot/dts/qcom/pm8018.dtsi
new file mode 100644
index 000000000000..22f3c7bac522
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/pm8018.dtsi
@@ -0,0 +1,55 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Device Tree Source for Qualcomm PM8018
+ *
+ * Copyright (C) 2016 BayLibre, SAS.
+ * Author : Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+&ssbi {
+	pm8018: pmic {
+		compatible = "qcom,pm8018", "qcom,pm8921";
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pwrkey@1c {
+			compatible = "qcom,pm8018-pwrkey",
+				     "qcom,pm8921-pwrkey";
+			reg = <0x1c>;
+			interrupts-extended = <&pm8018 50 IRQ_TYPE_EDGE_RISING>,
+					      <&pm8018 51 IRQ_TYPE_EDGE_RISING>;
+			debounce = <15625>;
+			pull-up;
+		};
+
+		pm8018_mpps: mpps@50 {
+			compatible = "qcom,pm8018-mpp", "qcom,ssbi-mpp";
+			reg = <0x50>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pm8018_mpps 0 0 6>;
+		};
+
+		rtc@11d {
+			compatible = "qcom,pm8018-rtc", "qcom,pm8921-rtc";
+			reg = <0x11d>;
+			interrupts-extended = <&pm8018 39 IRQ_TYPE_EDGE_RISING>;
+			allow-set-time;
+		};
+
+		pm8018_gpio: gpio@150 {
+			compatible = "qcom,pm8058-gpio",
+				     "qcom,ssbi-gpio";
+			reg = <0x150>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pm8018_gpio 0 0 6>;
+			#gpio-cells = <2>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/pm8058.dtsi b/arch/arm/boot/dts/qcom/pm8058.dtsi
new file mode 100644
index 000000000000..984b79777984
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/pm8058.dtsi
@@ -0,0 +1,159 @@
+// SPDX-License-Identifier: GPL-2.0
+
+&ssbi {
+	pm8058: pmic {
+		compatible = "qcom,pm8058";
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pwrkey@1c {
+			compatible = "qcom,pm8058-pwrkey";
+			reg = <0x1c>;
+			interrupts-extended = <&pm8058 50 IRQ_TYPE_EDGE_RISING>,
+					      <&pm8058 51 IRQ_TYPE_EDGE_RISING>;
+			debounce = <15625>;
+			pull-up;
+		};
+
+		pm8058_led48: led@48 {
+			compatible = "qcom,pm8058-keypad-led";
+			reg = <0x48>;
+			status = "disabled";
+		};
+
+		vibrator@4a {
+			compatible = "qcom,pm8058-vib";
+			reg = <0x4a>;
+		};
+
+		pm8058_mpps: mpps@50 {
+			compatible = "qcom,pm8058-mpp",
+				     "qcom,ssbi-mpp";
+			reg = <0x50>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pm8058_mpps 0 0 12>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pm8058_led131: led@131 {
+			compatible = "qcom,pm8058-led";
+			reg = <0x131>;
+			status = "disabled";
+		};
+
+		pm8058_led132: led@132 {
+			compatible = "qcom,pm8058-led";
+			reg = <0x132>;
+			status = "disabled";
+		};
+
+		pm8058_led133: led@133 {
+			compatible = "qcom,pm8058-led";
+			reg = <0x133>;
+			status = "disabled";
+		};
+
+		pm8058_keypad: keypad@148 {
+			compatible = "qcom,pm8058-keypad";
+			reg = <0x148>;
+			interrupts-extended = <&pm8058 74 IRQ_TYPE_EDGE_RISING>,
+					      <&pm8058 75 IRQ_TYPE_EDGE_RISING>;
+			debounce = <15>;
+			scan-delay = <32>;
+			row-hold = <91500>;
+		};
+
+		pm8058_gpio: gpio@150 {
+			compatible = "qcom,pm8058-gpio",
+				     "qcom,ssbi-gpio";
+			reg = <0x150>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pm8058_gpio 0 0 44>;
+			#gpio-cells = <2>;
+		};
+
+		pm8058_xoadc: xoadc@197 {
+			compatible = "qcom,pm8058-adc";
+			reg = <0x197>;
+			interrupts-extended = <&pm8058 76 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			#io-channel-cells = <2>;
+
+			vcoin: adc-channel@0 {
+				reg = <0x00 0x00>;
+			};
+
+			vbat: adc-channel@1 {
+				reg = <0x00 0x01>;
+			};
+
+			dcin: adc-channel@2 {
+				reg = <0x00 0x02>;
+			};
+
+			ichg: adc-channel@3 {
+				reg = <0x00 0x03>;
+			};
+
+			vph_pwr: adc-channel@4 {
+				reg = <0x00 0x04>;
+			};
+
+			usb_vbus: adc-channel@a {
+				reg = <0x00 0x0a>;
+			};
+
+			die_temp: adc-channel@b {
+				reg = <0x00 0x0b>;
+			};
+
+			ref_625mv: adc-channel@c {
+				reg = <0x00 0x0c>;
+			};
+
+			ref_1250mv: adc-channel@d {
+				reg = <0x00 0x0d>;
+			};
+
+			ref_325mv: adc-channel@e {
+				reg = <0x00 0x0e>;
+			};
+
+			ref_muxoff: adc-channel@f {
+				reg = <0x00 0x0f>;
+			};
+		};
+
+		rtc@1e8 {
+			compatible = "qcom,pm8058-rtc";
+			reg = <0x1e8>;
+			interrupts-extended = <&pm8058 39 IRQ_TYPE_EDGE_RISING>;
+			allow-set-time;
+		};
+	};
+};
+
+/ {
+	/*
+	 * These channels from the ADC are simply hardware monitors.
+	 * That is why the ADC is referred to as "HKADC" - HouseKeeping
+	 * ADC.
+	 */
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&pm8058_xoadc 0x00 0x01>, /* Battery */
+			      <&pm8058_xoadc 0x00 0x02>, /* DC in (charger) */
+			      <&pm8058_xoadc 0x00 0x04>, /* VPH the main system voltage */
+			      <&pm8058_xoadc 0x00 0x0b>, /* Die temperature */
+			      <&pm8058_xoadc 0x00 0x0c>, /* Reference voltage 1.25V */
+			      <&pm8058_xoadc 0x00 0x0d>, /* Reference voltage 0.625V */
+			      <&pm8058_xoadc 0x00 0x0e>; /* Reference voltage 0.325V */
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/pm8226.dtsi b/arch/arm/boot/dts/qcom/pm8226.dtsi
new file mode 100644
index 000000000000..2fd4f135ed84
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/pm8226.dtsi
@@ -0,0 +1,182 @@
+// SPDX-License-Identifier: BSD-3-Clause
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+	thermal-zones {
+		pm8226-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm8226_temp>;
+
+			trips {
+				trip0 {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <125000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+
+				crit {
+					temperature = <145000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
+&spmi_bus {
+	pm8226_0: pm8226@0 {
+		compatible = "qcom,pm8226", "qcom,spmi-pmic";
+		reg = <0x0 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pon@800 {
+			compatible = "qcom,pm8916-pon";
+			reg = <0x800>;
+
+			pwrkey {
+				compatible = "qcom,pm8941-pwrkey";
+				interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				linux,code = <KEY_POWER>;
+			};
+
+			pm8226_resin: resin {
+				compatible = "qcom,pm8941-resin";
+				interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				status = "disabled";
+			};
+		};
+
+		smbb: charger@1000 {
+			compatible = "qcom,pm8226-charger";
+			reg = <0x1000>;
+			interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>;
+			interrupt-names = "chg-done",
+					  "chg-fast",
+					  "chg-trkl",
+					  "bat-temp-ok",
+					  "bat-present",
+					  "chg-gone",
+					  "usb-valid",
+					  "dc-valid";
+
+			status = "disabled";
+
+			chg_otg: otg-vbus { };
+		};
+
+		pm8226_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
+			io-channels = <&pm8226_vadc VADC_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
+		pm8226_vadc: adc@3100 {
+			compatible = "qcom,spmi-vadc";
+			reg = <0x3100>;
+			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+
+			channel@7 {
+				reg = <VADC_VSYS>;
+				qcom,pre-scaling = <1 3>;
+				label = "vph_pwr";
+			};
+			channel@8 {
+				reg = <VADC_DIE_TEMP>;
+				label = "die_temp";
+			};
+			channel@9 {
+				reg = <VADC_REF_625MV>;
+				label = "ref_625mv";
+			};
+			channel@a {
+				reg = <VADC_REF_1250MV>;
+				label = "ref_1250mv";
+			};
+			channel@e {
+				reg = <VADC_GND_REF>;
+			};
+			channel@f {
+				reg = <VADC_VDD_VADC>;
+			};
+		};
+
+		pm8226_iadc: adc@3600 {
+			compatible = "qcom,pm8226-iadc", "qcom,spmi-iadc";
+			reg = <0x3600>;
+			interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>;
+		};
+
+		rtc@6000 {
+			compatible = "qcom,pm8941-rtc";
+			reg = <0x6000>, <0x6100>;
+			reg-names = "rtc", "alarm";
+			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
+		};
+
+		pm8226_mpps: mpps@a000 {
+			compatible = "qcom,pm8226-mpp", "qcom,spmi-mpp";
+			reg = <0xa000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pm8226_mpps 0 0 8>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pm8226_gpios: gpio@c000 {
+			compatible = "qcom,pm8226-gpio", "qcom,spmi-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pm8226_gpios 0 0 8>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pm8226_1: pm8226@1 {
+		compatible = "qcom,pm8226", "qcom,spmi-pmic";
+		reg = <0x1 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8226_spmi_regulators: regulators {
+			compatible = "qcom,pm8226-regulators";
+		};
+
+		pm8226_vib: vibrator@c000 {
+			compatible = "qcom,pm8916-vib";
+			reg = <0xc000>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/pm8821.dtsi b/arch/arm/boot/dts/qcom/pm8821.dtsi
new file mode 100644
index 000000000000..064e3ba54e18
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/pm8821.dtsi
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/* This PMIC is used on a secondary SSBI bus */
+&ssbi2 {
+	pm8821: pmic {
+		compatible = "qcom,pm8821";
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8821_mpps: mpps@50 {
+			compatible = "qcom,pm8821-mpp", "qcom,ssbi-mpp";
+			reg = <0x50>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pm8821_mpps 0 0 4>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom-pm8841.dtsi b/arch/arm/boot/dts/qcom/pm8841.dtsi
index 2caf71eacb52..3bf2ce5c86a6 100644
--- a/arch/arm/boot/dts/qcom-pm8841.dtsi
+++ b/arch/arm/boot/dts/qcom/pm8841.dtsi
@@ -2,6 +2,37 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/spmi/spmi.h>
 
+
+/ {
+	thermal-zones {
+		pm8841-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm8841_temp>;
+
+			trips {
+				trip0 {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <125000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+
+				crit {
+					temperature = <140000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
 &spmi_bus {
 
 	pm8841_0: pm8841@4 {
@@ -20,10 +51,11 @@
 			#interrupt-cells = <2>;
 		};
 
-		temp-alarm@2400 {
+		pm8841_temp: temp-alarm@2400 {
 			compatible = "qcom,spmi-temp-alarm";
 			reg = <0x2400>;
 			interrupts = <4 0x24 0 IRQ_TYPE_EDGE_RISING>;
+			#thermal-sensor-cells = <0>;
 		};
 	};
 
diff --git a/arch/arm/boot/dts/qcom/pm8921.dtsi b/arch/arm/boot/dts/qcom/pm8921.dtsi
new file mode 100644
index 000000000000..535cb6a2543f
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/pm8921.dtsi
@@ -0,0 +1,143 @@
+// SPDX-License-Identifier: GPL-2.0
+
+&ssbi {
+	pm8921: pmic {
+		compatible = "qcom,pm8921";
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pwrkey@1c {
+			compatible = "qcom,pm8921-pwrkey";
+			reg = <0x1c>;
+			interrupts-extended = <&pm8921 50 IRQ_TYPE_EDGE_RISING>,
+					      <&pm8921 51 IRQ_TYPE_EDGE_RISING>;
+			debounce = <15625>;
+			pull-up;
+		};
+
+		pm8921_vibrator: vibrator@4a {
+			compatible = "qcom,pm8921-vib";
+			reg = <0x4a>;
+			status = "disabled";
+		};
+
+		pm8921_mpps: mpps@50 {
+			compatible = "qcom,pm8921-mpp",
+				     "qcom,ssbi-mpp";
+			reg = <0x50>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pm8921_mpps 0 0 12>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		rtc@11d {
+			compatible = "qcom,pm8921-rtc";
+			reg = <0x11d>;
+			interrupts-extended = <&pm8921 39 IRQ_TYPE_EDGE_RISING>;
+			allow-set-time;
+		};
+
+		pm8921_keypad: keypad@148 {
+			compatible = "qcom,pm8921-keypad";
+			reg = <0x148>;
+			interrupts-extended = <&pm8921 74 IRQ_TYPE_EDGE_RISING>,
+					      <&pm8921 75 IRQ_TYPE_EDGE_RISING>;
+			debounce = <15>;
+			scan-delay = <32>;
+			row-hold = <91500>;
+			status = "disabled";
+		};
+
+		pm8921_gpio: gpio@150 {
+
+			compatible = "qcom,pm8921-gpio",
+				     "qcom,ssbi-gpio";
+			reg = <0x150>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pm8921_gpio 0 0 44>;
+			#gpio-cells = <2>;
+
+		};
+
+		pm8921_xoadc: xoadc@197 {
+			compatible = "qcom,pm8921-adc";
+			reg = <0x197>;
+			interrupts-extended = <&pm8921 78 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			#io-channel-cells = <2>;
+
+			vcoin: adc-channel@0 {
+				reg = <0x00 0x00>;
+			};
+
+			vbat: adc-channel@1 {
+				reg = <0x00 0x01>;
+			};
+
+			dcin: adc-channel@2 {
+				reg = <0x00 0x02>;
+			};
+
+			vph_pwr: adc-channel@4 {
+				reg = <0x00 0x04>;
+			};
+
+			batt_therm: adc-channel@8 {
+				reg = <0x00 0x08>;
+			};
+
+			batt_id: adc-channel@9 {
+				reg = <0x00 0x09>;
+			};
+
+			usb_vbus: adc-channel@a {
+				reg = <0x00 0x0a>;
+			};
+
+			die_temp: adc-channel@b {
+				reg = <0x00 0x0b>;
+			};
+
+			ref_625mv: adc-channel@c {
+				reg = <0x00 0x0c>;
+			};
+
+			ref_1250mv: adc-channel@d {
+				reg = <0x00 0x0d>;
+			};
+
+			chg_temp: adc-channel@e {
+				reg = <0x00 0x0e>;
+			};
+
+			ref_muxoff: adc-channel@f {
+				reg = <0x00 0x0f>;
+			};
+		};
+	};
+};
+
+/ {
+	/*
+	 * These channels from the ADC are simply hardware monitors.
+	 * That is why the ADC is referred to as "HKADC" - HouseKeeping
+	 * ADC.
+	 */
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&pm8921_xoadc 0x00 0x01>, /* Battery */
+			      <&pm8921_xoadc 0x00 0x02>, /* DC in (charger) */
+			      <&pm8921_xoadc 0x00 0x04>, /* VPH the main system voltage */
+			      <&pm8921_xoadc 0x00 0x0b>, /* Die temperature */
+			      <&pm8921_xoadc 0x00 0x0c>, /* Reference voltage 1.25V */
+			      <&pm8921_xoadc 0x00 0x0d>, /* Reference voltage 0.625V */
+			      <&pm8921_xoadc 0x00 0x0e>; /* Charger temperature */
+	};
+};
diff --git a/arch/arm/boot/dts/qcom-pm8941.dtsi b/arch/arm/boot/dts/qcom/pm8941.dtsi
index da00b8f5eecd..aca0052a02b7 100644
--- a/arch/arm/boot/dts/qcom-pm8941.dtsi
+++ b/arch/arm/boot/dts/qcom/pm8941.dtsi
@@ -3,6 +3,37 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/spmi/spmi.h>
 
+
+/ {
+	thermal-zones {
+		pm8941-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm8941_temp>;
+
+			trips {
+				trip0 {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <125000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+
+				crit {
+					temperature = <145000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
 &spmi_bus {
 
 	pm8941_0: pm8941@0 {
@@ -19,15 +50,27 @@
 			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
 		};
 
-		pwrkey@800 {
-			compatible = "qcom,pm8941-pwrkey";
+		pon@800 {
+			compatible = "qcom,pm8941-pon";
 			reg = <0x800>;
-			interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
-			debounce = <15625>;
-			bias-pull-up;
+
+			pwrkey {
+				compatible = "qcom,pm8941-pwrkey";
+				interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+			};
+
+			pm8941_resin: resin {
+				compatible = "qcom,pm8941-resin";
+				interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				status = "disabled";
+			};
 		};
 
-		usb_id: misc@900 {
+		usb_id: usb-detect@900 {
 			compatible = "qcom,pm8941-misc";
 			reg = <0x900>;
 			interrupts = <0x0 0x9 0 IRQ_TYPE_EDGE_BOTH>;
@@ -56,10 +99,12 @@
 
 			usb-otg-in-supply = <&pm8941_5vs1>;
 
+			status = "disabled";
+
 			chg_otg: otg-vbus { };
 		};
 
-		pm8941_gpios: gpios@c000 {
+		pm8941_gpios: gpio@c000 {
 			compatible = "qcom,pm8941-gpio", "qcom,spmi-gpio";
 			reg = <0xc000>;
 			gpio-controller;
@@ -68,7 +113,7 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 
-			boost_bypass_n_pin: boost-bypass {
+			boost_bypass_n_pin: boost-bypass-state {
 				pins = "gpio21";
 				function = "normal";
 			};
@@ -93,7 +138,7 @@
 			#thermal-sensor-cells = <0>;
 		};
 
-		pm8941_vadc: vadc@3100 {
+		pm8941_vadc: adc@3100 {
 			compatible = "qcom,spmi-vadc";
 			reg = <0x3100>;
 			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
@@ -101,37 +146,44 @@
 			#size-cells = <0>;
 			#io-channel-cells = <1>;
 
-			bat_temp {
-				reg = <VADC_LR_MUX1_BAT_THERM>;
+
+			channel@6 {
+				reg = <VADC_VBAT_SNS>;
 			};
-			die_temp {
+
+			channel@8 {
 				reg = <VADC_DIE_TEMP>;
 			};
-			ref_625mv {
+
+			channel@9 {
 				reg = <VADC_REF_625MV>;
 			};
-			ref_1250v {
+
+			channel@a {
 				reg = <VADC_REF_1250MV>;
 			};
-			ref_gnd {
+
+			channel@e {
 				reg = <VADC_GND_REF>;
 			};
-			ref_vdd {
+
+			channel@f {
 				reg = <VADC_VDD_VADC>;
 			};
-			vbat_sns {
-				reg = <VADC_VBAT_SNS>;
+
+			channel@30 {
+				reg = <VADC_LR_MUX1_BAT_THERM>;
 			};
 		};
 
-		pm8941_iadc: iadc@3600 {
+		pm8941_iadc: adc@3600 {
 			compatible = "qcom,pm8941-iadc", "qcom,spmi-iadc";
 			reg = <0x3600>;
 			interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>;
 			qcom,external-resistor-micro-ohms = <10000>;
 		};
 
-		coincell@2800 {
+		pm8941_coincell: charger@2800 {
 			compatible = "qcom,pm8941-coincell";
 			reg = <0x2800>;
 			status = "disabled";
@@ -144,6 +196,22 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
+		pm8941_lpg: pwm {
+			compatible = "qcom,pm8941-lpg";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#pwm-cells = <2>;
+
+			status = "disabled";
+		};
+
+		pm8941_vib: vibrator@c000 {
+			compatible = "qcom,pm8916-vib";
+			reg = <0xc000>;
+			status = "disabled";
+		};
+
 		pm8941_wled: wled@d800 {
 			compatible = "qcom,pm8941-wled";
 			reg = <0xd800>;
diff --git a/arch/arm/boot/dts/qcom-pma8084.dtsi b/arch/arm/boot/dts/qcom/pma8084.dtsi
index 7b8a8d9695da..309f5256754b 100644
--- a/arch/arm/boot/dts/qcom-pma8084.dtsi
+++ b/arch/arm/boot/dts/qcom/pma8084.dtsi
@@ -1,5 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 #include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/input/linux-event-codes.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/spmi/spmi.h>
 
@@ -19,15 +20,20 @@
 			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
 		};
 
-		pwrkey@800 {
-			compatible = "qcom,pm8941-pwrkey";
+		pon@800 {
+			compatible = "qcom,pm8941-pon";
 			reg = <0x800>;
-			interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
-			debounce = <15625>;
-			bias-pull-up;
+
+			pwrkey {
+				compatible = "qcom,pm8941-pwrkey";
+				interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				linux,code = <KEY_POWER>;
+			};
 		};
 
-		pma8084_gpios: gpios@c000 {
+		pma8084_gpios: gpio@c000 {
 			compatible = "qcom,pma8084-gpio", "qcom,spmi-gpio";
 			reg = <0xc000>;
 			gpio-controller;
@@ -56,7 +62,7 @@
 			io-channel-names = "thermal";
 		};
 
-		pma8084_vadc: vadc@3100 {
+		pma8084_vadc: adc@3100 {
 			compatible = "qcom,spmi-vadc";
 			reg = <0x3100>;
 			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
@@ -64,22 +70,27 @@
 			#size-cells = <0>;
 			#io-channel-cells = <1>;
 
-			die_temp {
+			channel@8 {
 				reg = <VADC_DIE_TEMP>;
 			};
-			ref_625mv {
+
+			channel@9 {
 				reg = <VADC_REF_625MV>;
 			};
-			ref_1250v {
+
+			channel@a {
 				reg = <VADC_REF_1250MV>;
 			};
-			ref_buf_625mv {
+
+			channel@c {
 				reg = <VADC_SPARE1>;
 			};
-			ref_gnd {
+
+			channel@e {
 				reg = <VADC_GND_REF>;
 			};
-			ref_vdd {
+
+			channel@f {
 				reg = <VADC_VDD_VADC>;
 			};
 		};
diff --git a/arch/arm/boot/dts/qcom-pmx55.dtsi b/arch/arm/boot/dts/qcom/pmx55.dtsi
index 6571b88d018a..da0851173c69 100644
--- a/arch/arm/boot/dts/qcom-pmx55.dtsi
+++ b/arch/arm/boot/dts/qcom/pmx55.dtsi
@@ -16,7 +16,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		power-on@800 {
+		pon@800 {
 			compatible = "qcom,pm8916-pon";
 			reg = <0x0800>;
 
@@ -40,25 +40,25 @@
 			#io-channel-cells = <1>;
 			interrupts = <0x8 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
 
-			ref-gnd@0 {
+			channel@0 {
 				reg = <ADC5_REF_GND>;
 				qcom,pre-scaling = <1 1>;
 				label = "ref_gnd";
 			};
 
-			vref-1p25@1 {
+			channel@1 {
 				reg = <ADC5_1P25VREF>;
 				qcom,pre-scaling = <1 1>;
 				label = "vref_1p25";
 			};
 
-			die-temp@6 {
+			channel@6 {
 				reg = <ADC5_DIE_TEMP>;
 				qcom,pre-scaling = <1 1>;
 				label = "die_temp";
 			};
 
-			chg-temp@9 {
+			channel@9 {
 				reg = <ADC5_CHG_TEMP>;
 				qcom,pre-scaling = <1 1>;
 				label = "chg_temp";
@@ -69,6 +69,7 @@
 			compatible = "qcom,pmx55-gpio", "qcom,spmi-gpio";
 			reg = <0xc000>;
 			gpio-controller;
+			gpio-ranges = <&pmx55_gpios 0 0 11>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
diff --git a/arch/arm/boot/dts/qcom/pmx65.dtsi b/arch/arm/boot/dts/qcom/pmx65.dtsi
new file mode 100644
index 000000000000..1c7fdf59c1f5
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/pmx65.dtsi
@@ -0,0 +1,33 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2022, Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+	pmic@1 {
+		compatible = "qcom,pmx65", "qcom,spmi-pmic";
+		reg = <1 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmx65_temp: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts = <0x1 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		pmx65_gpios: gpio@8800 {
+			compatible = "qcom,pmx65-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmx65_gpios 0 0 16>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom-apq8016-sbc.dts b/arch/arm/boot/dts/qcom/qcom-apq8016-sbc.dts
index 4ccd2dca74a2..4ccd2dca74a2 100644
--- a/arch/arm/boot/dts/qcom-apq8016-sbc.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8016-sbc.dts
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8026-asus-sparrow.dts b/arch/arm/boot/dts/qcom/qcom-apq8026-asus-sparrow.dts
new file mode 100644
index 000000000000..a2ca456012f1
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8026-asus-sparrow.dts
@@ -0,0 +1,300 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Luca Weiss <luca@z3ntu.xyz>
+ */
+
+/dts-v1/;
+
+#include "qcom-msm8226.dtsi"
+#include "pm8226.dtsi"
+
+/delete-node/ &adsp_region;
+
+/ {
+	model = "ASUS ZenWatch 2";
+	compatible = "asus,sparrow", "qcom,apq8026";
+	chassis-type = "watch";
+	qcom,msm-id = <199 0x20000>;
+	qcom,board-id = <8 3005>;
+
+	reserved-memory {
+		sbl_region: sbl@2f00000 {
+			reg = <0x02f00000 0x100000>;
+			no-map;
+		};
+		external_image_region: external-image@3100000 {
+			reg = <0x3100000 0x200000>;
+			no-map;
+		};
+		peripheral_region: peripheral@3300000 {
+			reg = <0x3300000 0x600000>;
+			no-map;
+		};
+		adsp_region: adsp@3900000 {
+			reg = <0x3900000 0x1400000>;
+			no-map;
+		};
+		modem_region: modem@4d00000 {
+			reg = <0x4d00000 0x1b00000>;
+			no-map;
+		};
+		modem_efs_region: modem-efs@7f00000 {
+			reg = <0x7f00000 0x100000>;
+			no-map;
+		};
+	};
+
+	vreg_wlan: wlan-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <2950000>;
+		regulator-max-microvolt = <2950000>;
+
+		gpio = <&tlmm 35 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_regulator_default_state>;
+	};
+};
+
+&adsp {
+	status = "okay";
+};
+
+&blsp1_uart1 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&blsp1_uart1_default_state>;
+
+	bluetooth {
+		compatible = "brcm,bcm43430a1-bt";
+		max-speed = <3000000>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&bluetooth_default_state>;
+
+		host-wakeup-gpios = <&tlmm 48 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&tlmm 61 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&tlmm 34 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&pm8226_vib {
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-pm8226-regulators";
+
+		pm8226_s3: s3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1300000>;
+		};
+		pm8226_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2200000>;
+		};
+		pm8226_s5: s5 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+		pm8226_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+		pm8226_l3: l3 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1337500>;
+		};
+		pm8226_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+		pm8226_l5: l5 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+		pm8226_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l7: l7 {
+			regulator-min-microvolt = <1900000>;
+			regulator-max-microvolt = <1900000>;
+		};
+		pm8226_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l14: l14 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+		};
+		pm8226_l15: l15 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+		pm8226_l16: l16 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+		pm8226_l17: l17 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		pm8226_l18: l18 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		pm8226_l19: l19 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+		pm8226_l20: l20 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+		pm8226_l21: l21 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		pm8226_l22: l22 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		pm8226_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l24: l24 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+		pm8226_l25: l25 {
+			regulator-min-microvolt = <1775000>;
+			regulator-max-microvolt = <2125000>;
+		};
+		pm8226_l26: l26 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+		pm8226_l27: l27 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+		pm8226_l28: l28 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_lvs1: lvs1 {};
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	vmmc-supply = <&pm8226_l17>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	bus-width = <8>;
+	non-removable;
+};
+
+&sdhc_3 {
+	status = "okay";
+
+	max-frequency = <100000000>;
+	non-removable;
+
+	vmmc-supply = <&vreg_wlan>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	wifi@1 {
+		compatible = "brcm,bcm43430a1-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
+
+		interrupts-extended = <&tlmm 46 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-names = "host-wake";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_hostwake_default_state>;
+	};
+};
+
+&smbb {
+	qcom,fast-charge-safe-current = <1500000>;
+	qcom,fast-charge-current-limit = <350000>;
+	qcom,fast-charge-safe-voltage = <4430000>;
+	qcom,fast-charge-high-threshold-voltage = <4400000>;
+	qcom,auto-recharge-threshold-voltage = <4300000>;
+	qcom,minimum-input-voltage = <4400000>;
+
+	status = "okay";
+};
+
+&tlmm {
+	blsp1_uart1_default_state: blsp1-uart1-default-state {
+		pins = "gpio0", "gpio1", "gpio2", "gpio3";
+		function = "blsp_uart1";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	bluetooth_default_state: bluetooth-default-state {
+		pins = "gpio48", "gpio61";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	wlan_hostwake_default_state: wlan-hostwake-default-state {
+		pins = "gpio46";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	wlan_regulator_default_state: wlan-regulator-default-state {
+		pins = "gpio35";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+};
+
+&usb {
+	status = "okay";
+	extcon = <&smbb>;
+	dr_mode = "peripheral";
+};
+
+&usb_hs_phy {
+	extcon = <&smbb>;
+	v1p8-supply = <&pm8226_l10>;
+	v3p3-supply = <&pm8226_l20>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8026-huawei-sturgeon.dts b/arch/arm/boot/dts/qcom/qcom-apq8026-huawei-sturgeon.dts
new file mode 100644
index 000000000000..ac228965a485
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8026-huawei-sturgeon.dts
@@ -0,0 +1,405 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Luca Weiss <luca@z3ntu.xyz>
+ */
+
+/dts-v1/;
+
+#include "qcom-msm8226.dtsi"
+#include "pm8226.dtsi"
+#include <dt-bindings/input/ti-drv260x.h>
+
+/delete-node/ &adsp_region;
+
+/ {
+	model = "Huawei Watch";
+	compatible = "huawei,sturgeon", "qcom,apq8026";
+	chassis-type = "watch";
+	qcom,msm-id = <199 0x20000>;
+	qcom,board-id = <8 4>;
+
+	reserved-memory {
+		sbl_region: sbl@2f00000 {
+			reg = <0x02f00000 0x100000>;
+			no-map;
+		};
+
+		external_image_region: external-image@3100000 {
+			reg = <0x3100000 0x200000>;
+			no-map;
+		};
+
+		peripheral_region: peripheral@3300000 {
+			reg = <0x3300000 0x600000>;
+			no-map;
+		};
+
+		adsp_region: adsp@3900000 {
+			reg = <0x3900000 0x1400000>;
+			no-map;
+		};
+
+		modem_region: modem@4d00000 {
+			reg = <0x4d00000 0x1b00000>;
+			no-map;
+		};
+
+		modem_efs_region: modem-efs@7f00000 {
+			reg = <0x7f00000 0x100000>;
+			no-map;
+		};
+	};
+
+	vreg_wlan: wlan-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <2950000>;
+		regulator-max-microvolt = <2950000>;
+
+		gpio = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_regulator_default_state>;
+	};
+};
+
+&adsp {
+	status = "okay";
+};
+
+&blsp1_i2c2 {
+	clock-frequency = <384000>;
+
+	status = "okay";
+
+	vibrator@5a {
+		compatible = "ti,drv2605";
+		reg = <0x5a>;
+		enable-gpios = <&tlmm 60 GPIO_ACTIVE_HIGH>;
+
+		mode = <DRV260X_ERM_MODE>;
+		library-sel = <DRV260X_ERM_LIB_D>;
+		vib-rated-mv = <2765>;
+		vib-overdrive-mv = <3525>;
+
+		pinctrl-0 = <&vibrator_default_state>;
+		pinctrl-names = "default";
+	};
+};
+
+&blsp1_i2c5 {
+	clock-frequency = <384000>;
+
+	status = "okay";
+
+	touchscreen@20 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x20>;
+
+		interrupts-extended = <&tlmm 17 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8226_l19>;
+		vio-supply = <&pm8226_lvs1>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&touch_default_state>;
+
+		syna,startup-delay-ms = <160>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmi4-f01@1 {
+			reg = <0x1>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp1_uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&blsp1_uart4_default_state>;
+
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43430a0-bt";
+		max-speed = <3000000>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&bluetooth_default_state>;
+
+		host-wakeup-gpios = <&tlmm 64 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&tlmm 63 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&tlmm 67 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-pm8226-regulators";
+
+		pm8226_s3: s3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8226_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2200000>;
+		};
+
+		pm8226_s5: s5 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8226_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l3: l3 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1337500>;
+		};
+
+		pm8226_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l5: l5 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l7: l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <1850000>;
+		};
+
+		pm8226_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l9: l9 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l14: l14 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+		};
+
+		pm8226_l15: l15 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+
+		pm8226_l16: l16 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3350000>;
+		};
+
+		pm8226_l17: l17 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l18: l18 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l19: l19 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8226_l20: l20 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+
+		pm8226_l21: l21 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l22: l22 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l24: l24 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8226_l25: l25 {
+			regulator-min-microvolt = <1775000>;
+			regulator-max-microvolt = <2125000>;
+		};
+
+		pm8226_l26: l26 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8226_l27: l27 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l28: l28 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_lvs1: lvs1 {};
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&pm8226_l17>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	bus-width = <8>;
+	non-removable;
+
+	status = "okay";
+};
+
+&sdhc_3 {
+	max-frequency = <100000000>;
+	non-removable;
+
+	vmmc-supply = <&vreg_wlan>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	status = "okay";
+
+	wifi@1 {
+		compatible = "brcm,bcm43430a0-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
+
+		interrupts-extended = <&tlmm 66 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-names = "host-wake";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_hostwake_default_state>;
+	};
+};
+
+&smbb {
+	qcom,fast-charge-safe-voltage = <4370000>;
+	qcom,fast-charge-high-threshold-voltage = <4350000>;
+	qcom,minimum-input-voltage = <4350000>;
+	qcom,fast-charge-current-limit = <300000>;
+	qcom,fast-charge-safe-current = <600000>;
+	qcom,auto-recharge-threshold-voltage = <4240000>;
+
+	status = "okay";
+};
+
+&tlmm {
+	blsp1_uart4_default_state: blsp1-uart4-default-state {
+		pins = "gpio12", "gpio13", "gpio14", "gpio15";
+		function = "blsp_uart4";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	bluetooth_default_state: bluetooth-default-state {
+		pins = "gpio63", "gpio64";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	touch_default_state: touch-default-state {
+		irq-pins {
+			pins = "gpio17";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		reset-pins {
+			pins = "gpio16";
+			function = "gpio";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+	};
+
+	vibrator_default_state: vibrator-default-state {
+		pins = "gpio59", "gpio60";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	wlan_hostwake_default_state: wlan-hostwake-default-state {
+		pins = "gpio66";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	wlan_regulator_default_state: wlan-regulator-default-state {
+		pins = "gpio110";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+};
+
+&usb {
+	extcon = <&smbb>;
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usb_hs_phy {
+	extcon = <&smbb>;
+	v1p8-supply = <&pm8226_l10>;
+	v3p3-supply = <&pm8226_l20>;
+};
diff --git a/arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts b/arch/arm/boot/dts/qcom/qcom-apq8026-lg-lenok.dts
index 2b7e52fda6a7..a70de21bf139 100644
--- a/arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8026-lg-lenok.dts
@@ -6,11 +6,15 @@
 /dts-v1/;
 
 #include "qcom-msm8226.dtsi"
-#include "qcom-pm8226.dtsi"
+#include "pm8226.dtsi"
+#include <dt-bindings/clock/qcom,mmcc-msm8974.h>
+
+/delete-node/ &adsp_region;
 
 / {
 	model = "LG G Watch R";
 	compatible = "lg,lenok", "qcom,apq8026";
+	chassis-type = "watch";
 	qcom,board-id = <132 0x0a>;
 	qcom,msm-id = <199 0x20000>;
 
@@ -23,6 +27,23 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	reserved-memory {
+		sbl_region: sbl@2f00000 {
+			reg = <0x02f00000 0x100000>;
+			no-map;
+		};
+
+		external_image_region: external-image@3100000 {
+			reg = <0x03100000 0x200000>;
+			no-map;
+		};
+
+		adsp_region: adsp@3300000 {
+			reg = <0x03300000 0x1400000>;
+			no-map;
+		};
+	};
+
 	vreg_wlan: wlan-regulator {
 		compatible = "regulator-fixed";
 
@@ -36,6 +57,33 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&wlan_regulator_default_state>;
 	};
+
+	pwm_vibrator: pwm {
+		compatible = "clk-pwm";
+		clocks = <&mmcc CAMSS_GP0_CLK>;
+
+		pinctrl-0 = <&vibrator_clk_default_state>;
+		pinctrl-names = "default";
+
+		#pwm-cells = <2>;
+	};
+
+	vibrator {
+		compatible = "pwm-vibrator";
+
+		pwms = <&pwm_vibrator 0 10000>;
+		pwm-names = "enable";
+
+		vcc-supply = <&pm8226_l28>;
+		enable-gpios = <&tlmm 62 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&vibrator_en_default_state>;
+		pinctrl-names = "default";
+	};
+};
+
+&adsp {
+	status = "okay";
 };
 
 &blsp1_i2c1 {
@@ -102,7 +150,7 @@
 };
 
 &rpm_requests {
-	pm8226-regulators {
+	regulators {
 		compatible = "qcom,rpm-pm8226-regulators";
 
 		pm8226_s3: s3 {
@@ -268,6 +316,8 @@
 	qcom,fast-charge-high-threshold-voltage = <4350000>;
 	qcom,auto-recharge-threshold-voltage = <4240000>;
 	qcom,minimum-input-voltage = <4450000>;
+
+	status = "okay";
 };
 
 &tlmm {
@@ -283,20 +333,18 @@
 		function = "gpio";
 		drive-strength = <2>;
 		bias-disable;
-		input-enable;
 	};
 
-	touch_pins: touch {
-		irq {
+	touch_pins: touch-state {
+		irq-pins {
 			pins = "gpio17";
 			function = "gpio";
 
 			drive-strength = <8>;
 			bias-pull-down;
-			input-enable;
 		};
 
-		reset {
+		reset-pins {
 			pins = "gpio16";
 			function = "gpio";
 
@@ -306,12 +354,25 @@
 		};
 	};
 
+	vibrator_clk_default_state: vibrator-clk-default-state {
+		pins = "gpio33";
+		function = "gp0_clk";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	vibrator_en_default_state: vibrator-en-default-state {
+		pins = "gpio62";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
 	wlan_hostwake_default_state: wlan-hostwake-default-state {
 		pins = "gpio37";
 		function = "gpio";
 		drive-strength = <2>;
 		bias-disable;
-		input-enable;
 	};
 
 	wlan_regulator_default_state: wlan-regulator-default-state {
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts b/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts
new file mode 100644
index 000000000000..4546fa8beba4
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts
@@ -0,0 +1,92 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Matti Lehtimäki <matti.lehtimaki@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "qcom-msm8226.dtsi"
+#include "qcom-msm8226-samsung-matisse-common.dtsi"
+
+/ {
+	model = "Samsung Galaxy Tab 4 10.1";
+	compatible = "samsung,matisse-wifi", "qcom,apq8026";
+	chassis-type = "tablet";
+
+	reg_tsp_3p3v: regulator-tsp-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "tsp_3p3v";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 73 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_en1_default_state>;
+	};
+};
+
+&blsp1_i2c2 {
+	status = "okay";
+
+	accelerometer@1d {
+		compatible = "st,lis2hh12";
+		reg = <0x1d>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <54 IRQ_TYPE_LEVEL_HIGH>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&accel_int_default_state>;
+
+		st,drdy-int-pin = <1>;
+
+		vdd-supply = <&pm8226_l19>;
+		vddio-supply = <&pm8226_lvs1>;
+	};
+};
+
+&blsp1_i2c5 {
+	status = "okay";
+
+	touchscreen@4a {
+		compatible = "atmel,maxtouch";
+		reg = <0x4a>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+
+		linux,keycodes = <KEY_RESERVED>,
+				 <KEY_RESERVED>,
+				 <KEY_RESERVED>,
+				 <KEY_RESERVED>,
+				 <KEY_APPSELECT>,
+				 <KEY_BACK>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_int_rst_default_state>;
+
+		reset-gpios = <&pm8226_gpios 6 GPIO_ACTIVE_LOW>;
+
+		vdd-supply = <&reg_tsp_1p8v>;
+		vdda-supply = <&reg_tsp_3p3v>;
+	};
+};
+
+&pm8226_l3 {
+	regulator-max-microvolt = <1337500>;
+};
+
+&pm8226_s4 {
+	regulator-max-microvolt = <1800000>;
+};
+
+&tlmm {
+	tsp_en1_default_state: tsp-en1-default-state {
+		pins = "gpio73";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-milletwifi.dts b/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-milletwifi.dts
new file mode 100644
index 000000000000..a8543ca7b556
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-milletwifi.dts
@@ -0,0 +1,575 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Matti Lehtimäki <matti.lehtimaki@gmail.com>
+ * Copyright (c) 2023, Bryant Mairs <bryant@mai.rs>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/power/summit,smb347-charger.h>
+#include "qcom-msm8226.dtsi"
+#include "pm8226.dtsi"
+
+/delete-node/ &adsp_region;
+/delete-node/ &mba_region;
+/delete-node/ &mpss_region;
+/delete-node/ &smem_region;
+
+/ {
+	model = "Samsung Galaxy Tab 4 8.0 Wi-Fi";
+	compatible = "samsung,milletwifi", "qcom,apq8026";
+	chassis-type = "tablet";
+
+	aliases {
+		display0 = &framebuffer0;
+		mmc0 = &sdhc_1; /* SDC1 eMMC slot */
+		mmc1 = &sdhc_2; /* SDC2 SD card slot */
+	};
+
+	chosen {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		stdout-path = "display0";
+
+		framebuffer0: framebuffer@3200000 {
+			compatible = "simple-framebuffer";
+			reg = <0x03200000 0x800000>;
+			width = <800>;
+			height = <1280>;
+			stride = <(800 * 3)>;
+			format = "r8g8b8";
+		};
+	};
+
+	gpio-hall-sensor {
+		compatible = "gpio-keys";
+
+		event-hall-sensor {
+			label = "Cover";
+			gpios = <&tlmm 37 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			debounce-interval = <15>;
+			linux,can-disable;
+			wakeup-source;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		key-home {
+			label = "Home";
+			gpios = <&tlmm 108 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOMEPAGE>;
+			debounce-interval = <15>;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <15>;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <15>;
+		};
+	};
+
+	i2c-backlight {
+		compatible = "i2c-gpio";
+		sda-gpios = <&tlmm 20 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&tlmm 21 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+
+		pinctrl-0 = <&backlight_i2c_default_state>;
+		pinctrl-names = "default";
+
+		i2c-gpio,delay-us = <4>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		backlight@2c {
+			compatible = "ti,lp8556";
+			reg = <0x2c>;
+			enable-supply = <&reg_backlight_vddio>;
+
+			dev-ctrl = /bits/ 8 <0x80>;
+			init-brt = /bits/ 8 <0x3f>;
+
+			/*
+			 * Change transition duration: 200ms, Change
+			 * transition strength: heavy, PWM hysteresis:
+			 * 1-bit w/ 8-bit resolution
+			 */
+			rom-a3h {
+				rom-addr = /bits/ 8 <0xa3>;
+				rom-val = /bits/ 8 <0x5e>;
+			};
+
+			/*
+			 * PWM phase configuration: 3-phase/3 drivers
+			 * (0, 120deg, 240deg, -, -, -),
+			 * PWM frequency: 9616Hz (10-bit)
+			 */
+			rom-a5h {
+				rom-addr = /bits/ 8 <0xa5>;
+				rom-val = /bits/ 8 <0x34>;
+			};
+
+			/*
+			 * Enable LED drivers 2 & 3, Boot inductor
+			 * current limit: 1.5A/2.6A
+			 */
+			rom-a7h {
+				rom-addr = /bits/ 8 <0xa7>;
+				rom-val = /bits/ 8 <0xfa>;
+			};
+		};
+	};
+
+	reg_backlight_vddio: regulator-backlight-vddio {
+		compatible = "regulator-fixed";
+		regulator-name = "backlight_vddio";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&tlmm 74 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&backlight_vddio_default_state>;
+		pinctrl-names = "default";
+	};
+
+	reg_tsp_1p8v: regulator-tsp-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "tsp_1p8v";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&tlmm 114 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&tsp_en1_default_state>;
+		pinctrl-names = "default";
+	};
+
+	reg_tsp_3p3v: regulator-tsp-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "tsp_3p3v";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 31 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&tsp_en_default_state>;
+		pinctrl-names = "default";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		framebuffer@3200000 {
+			reg = <0x03200000 0x800000>;
+			no-map;
+		};
+
+		mpss_region: mpss@8400000 {
+			reg = <0x08400000 0x1f00000>;
+			no-map;
+		};
+
+		mba_region: mba@a300000 {
+			reg = <0x0a300000 0x100000>;
+			no-map;
+		};
+
+		reserved@cb00000 {
+			reg = <0x0cb00000 0x700000>;
+			no-map;
+		};
+
+		wcnss_region: wcnss@d200000 {
+			reg = <0x0d200000 0x700000>;
+			no-map;
+		};
+
+		adsp_region: adsp@d900000 {
+			reg = <0x0d900000 0x1800000>;
+			no-map;
+		};
+
+		venus@f100000 {
+			reg = <0x0f100000 0x500000>;
+			no-map;
+		};
+
+		smem_region: smem@fa00000 {
+			reg = <0x0fa00000 0x100000>;
+			no-map;
+		};
+
+		reserved@fb00000 {
+			reg = <0x0fb00000 0x260000>;
+			no-map;
+		};
+
+		rfsa@fd60000 {
+			reg = <0x0fd60000 0x20000>;
+			no-map;
+		};
+
+		rmtfs@fd80000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0x0fd80000 0x180000>;
+			no-map;
+
+			qcom,client-id = <1>;
+		};
+	};
+};
+
+&blsp1_i2c2 {
+	status = "okay";
+
+	accelerometer@1d {
+		compatible = "st,lis2hh12";
+		reg = <0x1d>;
+
+		interrupts-extended = <&tlmm 54 IRQ_TYPE_LEVEL_HIGH>;
+
+		pinctrl-0 = <&accel_int_default_state>;
+		pinctrl-names = "default";
+
+		vdd-supply = <&pm8226_l19>;
+		vddio-supply = <&pm8226_lvs1>;
+
+		mount-matrix = "0", "1", "0",
+			       "-1", "0", "0",
+			       "0", "0", "1";
+
+		st,drdy-int-pin = <1>;
+	};
+};
+
+&blsp1_i2c3 {
+	status = "okay";
+
+	charger@6a {
+		compatible = "summit,smb358";
+		reg = <0x6a>;
+
+		interrupts-extended = <&tlmm 115 IRQ_TYPE_EDGE_FALLING>;
+
+		pinctrl-0 = <&charger_int_default_state>;
+		pinctrl-names = "default";
+
+		summit,enable-usb-charging;
+		summit,enable-charge-control = <SMB3XX_CHG_ENABLE_SW>;
+		summit,fast-voltage-threshold-microvolt = <3000000>;
+		summit,chip-temperature-threshold-celsius = <130>;
+		summit,usb-current-limit-microamp = <1500000>;
+	};
+};
+
+&blsp1_i2c4 {
+	status = "okay";
+
+	muic: usb-switch@25 {
+		compatible = "siliconmitus,sm5502-muic";
+		reg = <0x25>;
+
+		interrupts-extended = <&tlmm 67 IRQ_TYPE_EDGE_FALLING>;
+
+		pinctrl-0 = <&muic_int_default_state>;
+		pinctrl-names = "default";
+	};
+};
+
+&blsp1_i2c5 {
+	status = "okay";
+
+	touchscreen@48 {
+		compatible = "melfas,mms252", "melfas,mms114";
+		reg = <0x48>;
+		interrupts-extended = <&tlmm 17 IRQ_TYPE_EDGE_FALLING>;
+		touchscreen-size-x = <800>;
+		touchscreen-size-y = <1280>;
+		avdd-supply = <&reg_tsp_3p3v>;
+		vdd-supply = <&reg_tsp_1p8v>;
+		linux,keycodes = <KEY_APPSELECT KEY_BACK>;
+
+		pinctrl-0 = <&tsp_int_rst_default_state>;
+		pinctrl-names = "default";
+	};
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-pm8226-regulators";
+
+		pm8226_s3: s3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8226_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_s5: s5 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8226_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l3: l3 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1337500>;
+			regulator-always-on;
+		};
+
+		pm8226_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l5: l5 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		pm8226_l7: l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <1850000>;
+		};
+
+		pm8226_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		pm8226_l9: l9 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l14: l14 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+		};
+
+		pm8226_l15: l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8226_l16: l16 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3350000>;
+		};
+
+		pm8226_l17: l17 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+			regulator-always-on;
+		};
+
+		pm8226_l18: l18 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l19: l19 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8226_l20: l20 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+
+		pm8226_l21: l21 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l22: l22 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8226_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8226_l24: l24 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8226_l25: l25 {
+			regulator-min-microvolt = <1775000>;
+			regulator-max-microvolt = <2125000>;
+		};
+
+		pm8226_l26: l26 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8226_l27: l27 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l28: l28 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_lvs1: lvs1 {};
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&pm8226_l17>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	bus-width = <8>;
+	non-removable;
+
+	status = "okay";
+};
+
+&sdhc_2 {
+	vmmc-supply = <&pm8226_l18>;
+	vqmmc-supply = <&pm8226_l21>;
+
+	bus-width = <4>;
+	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+
+	pinctrl-0 = <&sdhc2_default_state>, <&sdc2_cd_default_state>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&tlmm {
+	accel_int_default_state: accel-int-default-state {
+		pins = "gpio54";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	backlight_i2c_default_state: backlight-i2c-default-state {
+		pins = "gpio20", "gpio21";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	backlight_vddio_default_state: backlight-vddio-default-state {
+		pins = "gpio74";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	charger_int_default_state: charger-int-default-state {
+		pins = "gpio115";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	muic_int_default_state: muic-int-default-state {
+		pins = "gpio67";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	sdc2_cd_default_state: sdc2-cd-default-state {
+		pins = "gpio38";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tsp_en_default_state: tsp-en-default-state {
+		pins = "gpio31";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tsp_en1_default_state: tsp-en1-default-state {
+		pins = "gpio114";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tsp_int_rst_default_state: tsp-int-rst-default-state {
+		pins = "gpio17";
+		function = "gpio";
+		drive-strength = <10>;
+		bias-pull-up;
+	};
+};
+
+&usb {
+	extcon = <&muic>, <&muic>;
+	status = "okay";
+};
+
+&usb_hs_phy {
+	extcon = <&muic>;
+	v1p8-supply = <&pm8226_l10>;
+	v3p3-supply = <&pm8226_l20>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts
new file mode 100644
index 000000000000..009afd8212c2
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8060-dragonboard.dts
@@ -0,0 +1,1024 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+#include "qcom-msm8660.dtsi"
+#include "pm8058.dtsi"
+
+/ {
+	model = "Qualcomm APQ8060 Dragonboard";
+	compatible = "qcom,apq8060-dragonboard", "qcom,msm8660";
+
+	aliases {
+		serial0 = &gsbi12_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	/* Main power of the board: 3.7V */
+	vph: regulator-fixed {
+		compatible = "regulator-fixed";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+		regulator-name = "VPH";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	/* GPIO controlled ethernet power regulator */
+	dragon_veth: xc622a331mrg {
+		compatible = "regulator-fixed";
+		regulator-name = "XC6222A331MR-G";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vph>;
+		gpio = <&pm8058_gpio 40 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_veth_gpios>;
+		regulator-always-on;
+	};
+
+	/* VDDvario fixed regulator */
+	dragon_vario: nds332p {
+		compatible = "regulator-fixed";
+		regulator-name = "NDS332P";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&pm8058_s3>;
+	};
+
+	/* This is a levelshifter for SDCC5 */
+	dragon_vio_txb: txb0104rgyr {
+		compatible = "regulator-fixed";
+		regulator-name = "Dragon SDCC levelshifter";
+		vin-supply = <&pm8058_l14>;
+		regulator-always-on;
+	};
+
+	/*
+	 * Capella CM3605 light and proximity sensor mounted directly
+	 * on the sensor board.
+	 */
+	cm3605 {
+		compatible = "capella,cm3605";
+		vdd-supply = <&pm8058_l14>; // 2.85V
+		aset-gpios = <&pm8058_gpio 35 GPIO_ACTIVE_LOW>;
+		capella,aset-resistance-ohms = <100000>;
+		/* Trig on both edges - getting close or far away */
+		interrupts-extended = <&pm8058_gpio 34 IRQ_TYPE_EDGE_BOTH>;
+		/* MPP05 analog input to the XOADC */
+		io-channels = <&pm8058_xoadc 0x00 0x05>;
+		io-channel-names = "aout";
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_cm3605_gpios>, <&dragon_cm3605_mpps>;
+	};
+};
+
+&ebi2 {
+	/* The EBI2 will instantiate first, then populate its children */
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_ebi2_pins>;
+	status = "okay";
+
+	/*
+	 * An on-board SMSC LAN9221 chip for "debug ethernet",
+	 * which is actually just an ordinary ethernet on the
+	 * EBI2. This has a 25MHz chrystal next to it, so no
+	 * clocking is needed.
+	 */
+	ethernet@2,0 {
+		compatible = "smsc,lan9221", "smsc,lan9115";
+		reg = <2 0x0 0x100>;
+		/*
+		 * The second interrupt is the PME interrupt
+		 * for network wakeup, connected to the TLMM.
+		 */
+		interrupts-extended = <&pm8058_gpio 7 IRQ_TYPE_EDGE_FALLING>,
+				    <&tlmm 29 IRQ_TYPE_EDGE_RISING>;
+		reset-gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
+		vdd33a-supply = <&dragon_veth>;
+		vddvario-supply = <&dragon_vario>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_ethernet_gpios>;
+		phy-mode = "mii";
+		reg-io-width = <2>;
+		smsc,force-external-phy;
+		smsc,irq-push-pull;
+
+		/*
+		 * SLOW chipselect config
+		 * Delay 9 cycles (140ns@64MHz) between SMSC
+		 * LAN9221 Ethernet controller reads and writes
+		 * on CS2.
+		 */
+		qcom,xmem-recovery-cycles = <0>;
+		qcom,xmem-write-hold-cycles = <3>;
+		qcom,xmem-write-delta-cycles = <31>;
+		qcom,xmem-read-delta-cycles = <28>;
+		qcom,xmem-write-wait-cycles = <9>;
+		qcom,xmem-read-wait-cycles = <9>;
+	};
+};
+
+&gsbi3 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+&gsbi3_i2c {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_gsbi3_i2c_pins>;
+	status = "okay";
+
+	touchscreen@24 {
+		compatible = "cypress,cy8ctma340";
+		reg = <0x24>;
+		/* Certainly we can do at least 400 kHz */
+		clock-frequency = <400000>;
+		/* IRQ on GPIO61 called /CTP_INT */
+		interrupt-parent = <&tlmm>;
+		interrupts = <61 IRQ_TYPE_EDGE_FALLING>;
+		/*
+		 * The I2C bus is using a PCA9306 level translator from L16A
+		 * to L2B so these two voltages are needed and L16A is
+		 * kind of the IO voltage, however L16Aisn't really fed to
+		 * the TMA340, which relies entirely on L2B (PM8901 L2).
+		 */
+		vcpin-supply = <&pm8058_l16>;
+		vdd-supply = <&pm8901_l2>;
+		/* GPIO58, called WAKE_CTP */
+		reset-gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
+		touchscreen-size-x = <480>;
+		touchscreen-size-y = <800>;
+		active-interval-ms = <0>;
+		touch-timeout-ms = <255>;
+		lowpower-interval-ms = <10>;
+		bootloader-key = /bits/ 8 <0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_tma340_gpios>;
+	};
+};
+
+&gsbi8 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+&gsbi8_i2c {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_gsbi8_i2c_pins>;
+	status = "okay";
+
+	eeprom@52 {
+		/* A 16KiB Platform ID EEPROM on the CPU carrier board */
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+		vcc-supply = <&pm8058_s3>;
+		pagesize = <64>;
+	};
+	wm8903: wm8903@1a {
+		/* This Woolfson Micro device has an unrouted interrupt line */
+		compatible = "wlf,wm8903";
+		reg = <0x1a>;
+
+		AVDD-supply = <&pm8058_l16>;
+		CPVDD-supply = <&pm8058_l16>;
+		DBVDD-supply = <&pm8058_s3>;
+		DCVDD-supply = <&pm8058_l0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		micdet-cfg = <0>;
+		micdet-delay = <100>;
+		gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
+	};
+};
+
+&gsbi12 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi12_serial {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_gsbi12_serial_pins>;
+	status = "okay";
+};
+
+&gsbi12_i2c {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_gsbi12_i2c_pins>;
+	status = "okay";
+
+	ak8975@c {
+		compatible = "asahi-kasei,ak8975";
+		reg = <0x0c>;
+		interrupt-parent = <&pm8058_gpio>;
+		interrupts = <33 IRQ_TYPE_EDGE_RISING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_ak8975_gpios>;
+		vid-supply = <&pm8058_lvs0>; // 1.8V
+		vdd-supply = <&pm8058_l14>; // 2.85V
+	};
+	bmp085@77 {
+		compatible = "bosch,bmp085";
+		reg = <0x77>;
+		interrupt-parent = <&pm8058_gpio>;
+		interrupts = <16 IRQ_TYPE_EDGE_RISING>;
+		reset-gpios = <&tlmm 86 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_bmp085_gpios>;
+		vddd-supply = <&pm8058_lvs0>; // 1.8V
+		vdda-supply = <&pm8058_l14>; // 2.85V
+	};
+	mpu3050@68 {
+		compatible = "invensense,mpu3050";
+		reg = <0x68>;
+		/*
+		 * GPIO17 is pulled high by a 10k
+		 * resistor to VLOGIC so needs to be
+		 * active low/falling edge.
+		 */
+		interrupts-extended = <&pm8058_gpio 17 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_mpu3050_gpios>;
+		vlogic-supply = <&pm8058_lvs0>; // 1.8V
+		vdd-supply = <&pm8058_l14>; // 2.85V
+
+		/*
+		 * The MPU-3050 acts as a hub for the
+		 * accelerometer.
+		 */
+		i2c-gate {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			kxsd9@18 {
+				compatible = "kionix,kxsd9";
+				reg = <0x18>;
+				interrupt-parent = <&tlmm>;
+				interrupts = <57 IRQ_TYPE_EDGE_FALLING>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&dragon_kxsd9_gpios>;
+				iovdd-supply = <&pm8058_lvs0>; // 1.8V
+				vdd-supply = <&pm8058_l14>; // 2.85V
+			};
+		};
+	};
+};
+
+&pm8058 {
+	interrupts-extended = <&tlmm 88 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&pm8058_gpio {
+	dragon_ethernet_gpios: ethernet-state {
+		pinconf {
+			pins = "gpio7";
+			function = "normal";
+			input-enable;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_bmp085_gpios: bmp085-state {
+		pinconf {
+			pins = "gpio16";
+			function = "normal";
+			input-enable;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_mpu3050_gpios: mpu3050-state {
+		pinconf {
+			pins = "gpio17";
+			function = "normal";
+			input-enable;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_sdcc3_gpios: sdcc3-state {
+		pinconf {
+			pins = "gpio22";
+			function = "normal";
+			input-enable;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_sdcc5_gpios: sdcc5-state {
+		pinconf {
+			pins = "gpio26";
+			function = "normal";
+			input-enable;
+			bias-pull-up;
+			qcom,pull-up-strength = <PMIC_GPIO_PULL_UP_30>;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_ak8975_gpios: ak8975-state {
+		pinconf {
+			pins = "gpio33";
+			function = "normal";
+			input-enable;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_cm3605_gpios: cm3605-state {
+		/* Pin 34 connected to the proxy IRQ */
+		gpio34-pins {
+			pins = "gpio34";
+			function = "normal";
+			input-enable;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+		/* Pin 35 connected to ASET */
+		gpio35-pins {
+			pins = "gpio35";
+			function = "normal";
+			output-high;
+			bias-disable;
+			power-source = <PM8058_GPIO_S3>;
+		};
+	};
+	dragon_veth_gpios: veth-state {
+		pinconf {
+			pins = "gpio40";
+			function = "normal";
+			bias-disable;
+			drive-push-pull;
+		};
+	};
+};
+
+&pm8058_keypad {
+	linux,keymap = <
+		MATRIX_KEY(0, 0, KEY_MENU)
+		MATRIX_KEY(0, 2, KEY_1)
+		MATRIX_KEY(0, 3, KEY_4)
+		MATRIX_KEY(0, 4, KEY_7)
+		MATRIX_KEY(1, 0, KEY_UP)
+		MATRIX_KEY(1, 1, KEY_LEFT)
+		MATRIX_KEY(1, 2, KEY_DOWN)
+		MATRIX_KEY(1, 3, KEY_5)
+		MATRIX_KEY(1, 3, KEY_8)
+		MATRIX_KEY(2, 0, KEY_HOME)
+		MATRIX_KEY(2, 1, KEY_REPLY)
+		MATRIX_KEY(2, 2, KEY_2)
+		MATRIX_KEY(2, 3, KEY_6)
+		MATRIX_KEY(3, 0, KEY_VOLUMEUP)
+		MATRIX_KEY(3, 1, KEY_RIGHT)
+		MATRIX_KEY(3, 2, KEY_3)
+		MATRIX_KEY(3, 3, KEY_9)
+		MATRIX_KEY(3, 4, KEY_SWITCHVIDEOMODE)
+		MATRIX_KEY(4, 0, KEY_VOLUMEDOWN)
+		MATRIX_KEY(4, 1, KEY_BACK)
+		MATRIX_KEY(4, 2, KEY_CAMERA)
+		MATRIX_KEY(4, 3, KEY_KBDILLUMTOGGLE)
+	>;
+	keypad,num-rows = <6>;
+	keypad,num-columns = <5>;
+};
+
+&pm8058_led48 {
+	/*
+	 * The keypad LED @0x48 is routed to
+	 * the sensor board where it is
+	 * connected to an infrared LED
+	 * SFH4650 (60mW, @850nm) next to the
+	 * ambient light and proximity sensor
+	 * Capella Microsystems CM3605.
+	 */
+	label = "pm8058:infrared:proximitysensor";
+	default-state = "off";
+	linux,default-trigger = "cm3605";
+	status = "okay";
+};
+
+&pm8058_led131 {
+	label = "pm8058:red";
+	color = <LED_COLOR_ID_RED>;
+	default-state = "off";
+	status = "okay";
+};
+
+&pm8058_led132 {
+	/*
+	 * This is actually green too on my
+	 * board, but documented as yellow.
+	 */
+	label = "pm8058:yellow";
+	color = <LED_COLOR_ID_YELLOW>;
+	default-state = "off";
+	linux,default-trigger = "mmc0";
+	status = "okay";
+};
+
+&pm8058_led133 {
+	label = "pm8058:green";
+	function = LED_FUNCTION_HEARTBEAT;
+	color = <LED_COLOR_ID_GREEN>;
+	default-state = "on";
+	linux,default-trigger = "heartbeat";
+	status = "okay";
+};
+
+&pm8058_mpps {
+	dragon_cm3605_mpps: cm3605-mpps-state {
+		pins = "mpp5";
+		function = "analog";
+		input-enable;
+		bias-high-impedance;
+		/* Let's use channel 5 */
+		qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH5>;
+		power-source = <PM8058_GPIO_S3>;
+	};
+};
+
+&rpm {
+	/*
+	 * Set up of the PMIC RPM regulators for this board
+	 * PM8901 supplies "preliminary regulators" whatever
+	 * that means
+	 */
+	regulators-0 {
+		compatible = "qcom,rpm-pm8901-regulators";
+
+		vdd_l0-supply = <&pm8901_s4>;
+		vdd_l1-supply = <&vph>;
+		vdd_l2-supply = <&vph>;
+		vdd_l3-supply = <&vph>;
+		vdd_l4-supply = <&vph>;
+		vdd_l5-supply = <&vph>;
+		vdd_l6-supply = <&vph>;
+		/* vdd_s0-supply, vdd_s1-supply: SAW regulators */
+		vdd_s2-supply = <&vph>;
+		vdd_s3-supply = <&vph>;
+		vdd_s4-supply = <&vph>;
+		lvs0_in-supply = <&pm8058_s3>;
+		lvs1_in-supply = <&pm8901_s4>;
+		lvs2_in-supply = <&pm8058_l0>;
+		lvs3_in-supply = <&pm8058_s2>;
+		mvs_in-supply = <&pm8058_s3>;
+
+		pm8901_l0: l0 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8901_l1: l1 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+
+		pm8901_l2: l2 {
+			/* TMA340 requires strictly 3.3V */
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+
+		pm8901_l3: l3 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+
+		pm8901_l4: l4 {
+			regulator-min-microvolt = <2600000>;
+			regulator-max-microvolt = <2600000>;
+			bias-pull-down;
+		};
+
+		pm8901_l5: l5 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+
+		pm8901_l6: l6 {
+			regulator-min-microvolt = <2200000>;
+			regulator-max-microvolt = <2200000>;
+			bias-pull-down;
+		};
+
+		/* s0 and s1 are SAW regulators controlled over SPM */
+		pm8901_s2: s2 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+		pm8901_s3: s3 {
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+		pm8901_s4: s4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		/* LVS0 thru 3 and mvs are just switches */
+		pm8901_lvs0: lvs0 {
+			regulator-always-on;
+		};
+
+		pm8901_lvs1: lvs1 { };
+
+		pm8901_lvs2: lvs2 { };
+
+		pm8901_lvs3: lvs3 { };
+
+		pm8901_mvs: mvs { };
+	};
+
+	regulators-1 {
+		compatible = "qcom,rpm-pm8058-regulators";
+
+		vdd_l0_l1_lvs-supply = <&pm8058_s3>;
+		vdd_l2_l11_l12-supply = <&vph>;
+		vdd_l3_l4_l5-supply = <&vph>;
+		vdd_l6_l7-supply = <&vph>;
+		vdd_l8-supply = <&vph>;
+		vdd_l9-supply = <&vph>;
+		vdd_l10-supply = <&vph>;
+		vdd_l13_l16-supply = <&pm8058_s4>;
+		vdd_l14_l15-supply = <&vph>;
+		vdd_l17_l18-supply = <&vph>;
+		vdd_l19_l20-supply = <&vph>;
+		vdd_l21-supply = <&pm8058_s3>;
+		vdd_l22-supply = <&pm8058_s3>;
+		vdd_l23_l24_l25-supply = <&pm8058_s3>;
+		vdd_s0-supply = <&vph>;
+		vdd_s1-supply = <&vph>;
+		vdd_s2-supply = <&vph>;
+		vdd_s3-supply = <&vph>;
+		vdd_s4-supply = <&vph>;
+		vdd_ncp-supply = <&vph>;
+
+		pm8058_l0: l0 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8058_l1: l1 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8058_l2: l2 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2600000>;
+			bias-pull-down;
+		};
+
+		pm8058_l3: l3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8058_l4: l4 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+
+		pm8058_l5: l5 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+
+		pm8058_l6: l6 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3600000>;
+			bias-pull-down;
+		};
+
+		pm8058_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8058_l8: l8 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <3050000>;
+			bias-pull-down;
+		};
+
+		pm8058_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8058_l10: l10 {
+			regulator-min-microvolt = <2600000>;
+			regulator-max-microvolt = <2600000>;
+			bias-pull-down;
+		};
+
+		pm8058_l11: l11 {
+			regulator-min-microvolt = <1500000>;
+			regulator-max-microvolt = <1500000>;
+			bias-pull-down;
+		};
+
+		pm8058_l12: l12 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <2900000>;
+			bias-pull-down;
+		};
+
+		pm8058_l13: l13 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+			bias-pull-down;
+		};
+
+		pm8058_l14: l14 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8058_l15: l15 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+
+		pm8058_l16: l16 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+			regulator-always-on;
+		};
+
+		pm8058_l17: l17 {
+			// 1.5V according to schematic
+			regulator-min-microvolt = <2600000>;
+			regulator-max-microvolt = <2600000>;
+			bias-pull-down;
+		};
+
+		pm8058_l18: l18 {
+			regulator-min-microvolt = <2200000>;
+			regulator-max-microvolt = <2200000>;
+			bias-pull-down;
+		};
+
+		pm8058_l19: l19 {
+			regulator-min-microvolt = <2500000>;
+			regulator-max-microvolt = <2500000>;
+			bias-pull-down;
+		};
+
+		pm8058_l20: l20 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8058_l21: l21 {
+			// 1.1 V according to schematic
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+			regulator-always-on;
+		};
+
+		pm8058_l22: l22 {
+			// 1.2 V according to schematic
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+			bias-pull-down;
+		};
+
+		pm8058_l23: l23 {
+			// Unused
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8058_l24: l24 {
+			// Unused
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8058_l25: l25 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8058_s0: s0 {
+			// regulator-min-microvolt = <500000>;
+			// regulator-max-microvolt = <1325000>;
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8058_s1: s1 {
+			// regulator-min-microvolt = <500000>;
+			// regulator-max-microvolt = <1250000>;
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8058_s2: s2 {
+			// 1.3 V according to schematic
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1400000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8058_s3: s3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+			regulator-always-on;
+			bias-pull-down;
+		};
+
+		pm8058_s4: s4 {
+			regulator-min-microvolt = <2200000>;
+			regulator-max-microvolt = <2200000>;
+			qcom,switch-mode-frequency = <1600000>;
+			regulator-always-on;
+			bias-pull-down;
+		};
+
+		/* LVS0 and LVS1 are just switches */
+		pm8058_lvs0: lvs0 {
+			bias-pull-down;
+		};
+
+		pm8058_lvs1: lvs1 {
+			bias-pull-down;
+		};
+
+		pm8058_ncp: ncp {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+		};
+	};
+};
+
+/* Internal 3.69 GiB eMMC */
+&sdcc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_sdcc1_pins>;
+	vmmc-supply = <&pm8901_l5>;
+	vqmmc-supply = <&pm8901_lvs0>;
+	status = "okay";
+};
+
+/* External micro SD card, directly connected, pulled up to 2.85 V */
+&sdcc3 {
+	/* Enable SSBI GPIO 22 as input, use for card detect */
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_sdcc3_pins>, <&dragon_sdcc3_gpios>;
+	cd-gpios = <&pm8058_gpio 22 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&pm8058_l14>;
+	status = "okay";
+};
+
+/*
+ * Second external micro SD card, using two TXB104RGYR levelshifters
+ * to lift from 1.8 V to 2.85 V
+ */
+&sdcc5 {
+	/* Enable SSBI GPIO 26 as input, use for card detect */
+	pinctrl-names = "default";
+	pinctrl-0 = <&dragon_sdcc5_pins>, <&dragon_sdcc5_gpios>;
+	cd-gpios = <&pm8058_gpio 26 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&tlmm 106 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&pm8058_l14>;
+	vqmmc-supply = <&dragon_vio_txb>;
+	status = "okay";
+};
+
+&tlmm {
+	/* eMMC pins, all 8 data lines connected */
+	dragon_sdcc1_pins: sdcc1-state {
+		clk-pins {
+			pins = "gpio167"; /* SDC1 CLK */
+			function = "sdc1";
+			drive-strength = <16>;
+			bias-disable;
+		};
+		cmd-pins {
+			pins = "gpio168"; /* SDC1 CMD */
+			function = "sdc1";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+		data-pins {
+			/* SDC1 D0 to D7 */
+			pins = "gpio159", "gpio160", "gpio161", "gpio162",
+			     "gpio163", "gpio164", "gpio165", "gpio166";
+			function = "sdc1";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	/*
+	 * The SDCC3 pins are hardcoded (non-muxable) but need some pin
+	 * configuration.
+	 */
+	dragon_sdcc3_pins: sdcc3-state {
+		clk-pins {
+			pins = "sdc3_clk";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		cmd-pins {
+			pins = "sdc3_cmd";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+		data-pins {
+			pins = "sdc3_data";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	/* Second SD card slot pins */
+	dragon_sdcc5_pins: sdcc5-state {
+		clk-pins {
+			pins = "gpio97"; /* SDC5 CLK */
+			function = "sdc5";
+			drive-strength = <16>;
+			bias-disable;
+		};
+		cmd-pins {
+			pins = "gpio95"; /* SDC5 CMD */
+			function = "sdc5";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+		data-pins {
+			/* SDC5 D0 to D3 */
+			pins = "gpio96", "gpio98", "gpio99", "gpio100";
+			function = "sdc5";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	dragon_gsbi3_i2c_pins: gsbi3-i2c-state {
+		pins = "gpio43", "gpio44";
+		function = "gsbi3";
+		drive-strength = <8>;
+		/* These have external pull-up 2.2kOhm to 1.8V */
+		bias-disable;
+	};
+
+	dragon_gsbi8_i2c_pins: gsbi8-i2c-state {
+		pins = "gpio64", "gpio65";
+		function = "gsbi8";
+		drive-strength = <16>;
+		/* These have external pull-up 2.2kOhm to 1.8V */
+		bias-disable;
+	};
+
+	dragon_gsbi12_i2c_pins: gsbi12-i2c-state {
+		pins = "gpio115", "gpio116";
+		function = "gsbi12";
+		drive-strength = <16>;
+		/* These have external pull-up 4.7kOhm to 1.8V */
+		bias-disable;
+	};
+
+	/* Primary serial port uart 0 pins */
+	dragon_gsbi12_serial_pins: gsbi12-serial-state {
+		tx-pins {
+			pins = "gpio117";
+			function = "gsbi12";
+			drive-strength = <8>;
+			bias-disable;
+		};
+		rx-pins {
+			pins = "gpio118";
+			function = "gsbi12";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	dragon_ebi2_pins: ebi2-state {
+		/*
+		 * Pins used by EBI2 on the Dragonboard, actually only
+		 * CS2 is used by a real peripheral. CS0 is just
+		 * routed to a test point.
+		 */
+		mux0-pins {
+			pins =
+			    /* "gpio39", CS1A_N this is not good to mux */
+			    "gpio40", /* CS2A_N */
+			    "gpio134"; /* CS0_N testpoint TP29 */
+			function = "ebi2cs";
+		};
+		mux1-pins {
+			pins =
+			    /* EBI2_ADDR_7 downto EBI2_ADDR_0 address bus */
+			    "gpio123", "gpio124", "gpio125", "gpio126",
+			    "gpio127", "gpio128", "gpio129", "gpio130",
+			    /* EBI2_DATA_15 downto EBI2_DATA_0 data bus */
+			    "gpio135", "gpio136", "gpio137", "gpio138",
+			    "gpio139", "gpio140", "gpio141", "gpio142",
+			    "gpio143", "gpio144", "gpio145", "gpio146",
+			    "gpio147", "gpio148", "gpio149", "gpio150",
+			    "gpio151", /* EBI2_OE_N */
+			    "gpio153", /* EBI2_ADV */
+			    "gpio157"; /* EBI2_WE_N */
+			function = "ebi2";
+		};
+	};
+
+	/* Interrupt line for the KXSD9 accelerometer */
+	dragon_kxsd9_gpios: kxsd9-state {
+		pins = "gpio57"; /* IRQ line */
+		function = "gpio";
+		bias-pull-up;
+	};
+
+	dragon_tma340_gpios: tma340-state {
+		reset-pins {
+			/* RESET line, TS_ATTN, WAKE_CTP */
+			pins = "gpio58";
+			function = "gpio";
+			drive-strength = <6>;
+			bias-disable;
+		};
+		irq-pins {
+			pins = "gpio61"; /* IRQ line */
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+};
+
+&pm8058_xoadc {
+	/* Reference voltage 2.2 V */
+	xoadc-ref-supply = <&pm8058_l18>;
+
+	/* Board-specific channels */
+	adc-channel@5 {
+		/* Connected to AOUT of ALS sensor */
+		reg = <0x00 0x05>;
+	};
+
+	adc-channel@6 {
+		/* Connected to test point TP43 */
+		reg = <0x00 0x06>;
+	};
+
+	adc-channel@7 {
+		/* Connected to battery thermistor */
+		reg = <0x00 0x07>;
+	};
+
+	adc-channel@8 {
+		/* Connected to battery ID detector */
+		reg = <0x00 0x08>;
+	};
+
+	adc-channel@9 {
+		/* Connected to XO thermistor */
+		reg = <0x00 0x09>;
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts
new file mode 100644
index 000000000000..947183992850
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-asus-nexus7-flo.dts
@@ -0,0 +1,359 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+#include "qcom-apq8064-v2.0.dtsi"
+#include "pm8821.dtsi"
+#include "pm8921.dtsi"
+
+/ {
+	model = "Asus Nexus7(flo)";
+	compatible = "asus,nexus7-flo", "qcom,apq8064";
+	chassis-type = "tablet";
+
+	aliases {
+		serial0 = &gsbi7_serial;
+		serial1 = &gsbi6_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		ramoops@88d00000 {
+			compatible = "ramoops";
+			reg = <0x88d00000 0x100000>;
+			record-size = <0x00020000>;
+			console-size = <0x00020000>;
+			ftrace-size = <0x00020000>;
+		};
+	};
+
+	ext_3p3v: regulator-ext-3p3v {
+		compatible = "regulator-fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "ext_3p3v";
+		startup-delay-us = <0>;
+		gpio = <&tlmm_pinmux 77 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&pm8921_gpio 4 GPIO_ACTIVE_HIGH>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&pm8921_gpio 38 GPIO_ACTIVE_HIGH>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+	};
+
+	soc {
+		sram@2a03f000 {
+			compatible = "qcom,apq8064-imem", "syscon", "simple-mfd";
+			reg = <0x2a03f000 0x1000>;
+
+			reboot-mode {
+				compatible = "syscon-reboot-mode";
+				offset = <0x65c>;
+
+				mode-normal = <0x77665501>;
+				mode-bootloader = <0x77665500>;
+				mode-recovery = <0x77665502>;
+			};
+		};
+	};
+};
+
+&dsi0 {
+	vdda-supply = <&pm8921_l2>;/*VDD_MIPI1 to 4*/
+	vdd-supply = <&pm8921_l8>;
+	vddio-supply = <&pm8921_lvs7>;
+	avdd-supply = <&pm8921_l11>;
+	status = "okay";
+
+	panel@0 {
+		reg = <0>;
+		compatible = "jdi,lt070me05000";
+
+		vddp-supply = <&pm8921_l17>;
+		iovcc-supply = <&pm8921_lvs7>;
+
+		enable-gpios = <&pm8921_gpio 36 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&tlmm_pinmux 54 GPIO_ACTIVE_LOW>;
+		dcdc-en-gpios = <&pm8921_gpio 23 GPIO_ACTIVE_HIGH>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&dsi0_out>;
+			};
+		};
+	};
+};
+
+&dsi0_in {
+	remote-endpoint = <&mdp_dsi1_out>;
+};
+
+&dsi0_out {
+	remote-endpoint = <&panel_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&dsi0_phy {
+	vddio-supply = <&pm8921_lvs7>;/*VDD_PLL2_1 to 7*/
+	status = "okay";
+};
+
+&gsbi1 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+&gsbi1_i2c {
+	status = "okay";
+	clock-frequency = <200000>;
+
+	eeprom@52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+		pagesize = <32>;
+	};
+
+	bq27541@55 {
+		compatible = "ti,bq27541";
+		reg = <0x55>;
+	};
+
+};
+
+&gsbi3 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+&gsbi3_i2c {
+	clock-frequency = <200000>;
+	status = "okay";
+
+	trackpad@10 {
+		compatible = "elan,ekth3500";
+		reg = <0x10>;
+		interrupt-parent = <&tlmm_pinmux>;
+		interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+	};
+};
+
+&gsbi6 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi6_serial {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gsbi6_uart_4pins>;
+	status = "okay";
+};
+
+&gsbi7 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi7_serial {
+	status = "okay";
+};
+
+&mdp {
+	status = "okay";
+};
+
+&mdp_dsi1_out {
+	remote-endpoint = <&dsi0_in>;
+};
+
+&pm8821 {
+	interrupts-extended = <&tlmm_pinmux 76 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&pm8921 {
+	interrupts-extended = <&tlmm_pinmux 74 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&rpm {
+	regulators {
+		compatible = "qcom,rpm-pm8921-regulators";
+
+		vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+		vin_lvs1_3_6-supply = <&pm8921_s4>;
+		vin_lvs4_5_7-supply = <&pm8921_s4>;
+
+		vdd_l24-supply = <&pm8921_s1>;
+		vdd_l25-supply = <&pm8921_s1>;
+		vin_lvs2-supply = <&pm8921_s1>;
+
+		vdd_l26-supply = <&pm8921_s7>;
+		vdd_l27-supply = <&pm8921_s7>;
+		vdd_l28-supply = <&pm8921_s7>;
+
+		vdd_ncp-supply = <&pm8921_l6>;
+
+		/* Buck SMPS */
+		pm8921_s1: s1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		/* msm otg HSUSB_VDDCX */
+		pm8921_s3: s3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <4800000>;
+		};
+
+		/*
+		 * msm_sdcc.1-sdc-vdd_io
+		 * tabla2x-slim-CDC_VDDA_RX
+		 * tabla2x-slim-CDC_VDDA_TX
+		 * tabla2x-slim-CDC_VDD_CP
+		 * tabla2x-slim-VDDIO_CDC
+		 */
+		pm8921_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <3200000>;
+			regulator-always-on;
+		};
+
+		pm8921_s7: s7 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <3200000>;
+		};
+
+		/* mipi_dsi.1-dsi1_pll_vdda */
+		pm8921_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-always-on;
+		};
+
+		/* msm_otg-HSUSB_3p3 */
+		pm8921_l3: l3 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			bias-pull-down;
+		};
+
+		/* msm_otg-HSUSB_1p8 */
+		pm8921_l4: l4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		/* msm_sdcc.1-sdc_vdd */
+		pm8921_l5: l5 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-always-on;
+			bias-pull-down;
+		};
+
+		pm8921_l6: l6 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8921_l8: l8 {
+		};
+
+		/* mipi_dsi.1-dsi1_avdd */
+		pm8921_l11: l11 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+			regulator-always-on;
+		};
+
+		/* pwm_power for backlight */
+		pm8921_l17: l17 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-always-on;
+		};
+
+		/* camera, qdsp6 */
+		pm8921_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		/*
+		 * tabla2x-slim-CDC_VDDA_A_1P2V
+		 * tabla2x-slim-VDDD_CDC_D
+		 */
+		pm8921_l25: l25 {
+			regulator-min-microvolt = <1250000>;
+			regulator-max-microvolt = <1250000>;
+			bias-pull-down;
+		};
+
+		pm8921_lvs1: lvs1 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs4: lvs4 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs5: lvs5 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs6: lvs6 {
+			bias-pull-down;
+		};
+		/*
+		 * mipi_dsi.1-dsi1_vddio
+		 * pil_riva-pll_vdd
+		 */
+		pm8921_lvs7: lvs7 {
+			bias-pull-down;
+		};
+	};
+};
+
+/* eMMC */
+&sdcc1 {
+	vmmc-supply = <&pm8921_l5>;
+	vqmmc-supply = <&pm8921_s4>;
+	status = "okay";
+};
+
+&usb_hs1_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l4>;
+};
+
+/* OTG */
+&usb1 {
+	dr_mode = "otg";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-cm-qs600.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-cm-qs600.dts
new file mode 100644
index 000000000000..178c55c1efeb
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-cm-qs600.dts
@@ -0,0 +1,234 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+#include "qcom-apq8064-v2.0.dtsi"
+#include "pm8821.dtsi"
+#include "pm8921.dtsi"
+
+/ {
+	model = "CompuLab CM-QS600";
+	compatible = "qcom,apq8064-cm-qs600", "qcom,apq8064";
+
+	aliases {
+		serial0 = &gsbi7_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	sdcc4_pwrseq: pwrseq-sdcc4 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_default_gpios>;
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pm8921_gpio 43 GPIO_ACTIVE_LOW>;
+	};
+
+	/* on board fixed 3.3v supply */
+	v3p3_fixed: regulator-v3p3 {
+		compatible = "regulator-fixed";
+		regulator-name = "PCIE V3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+};
+
+&gsbi1 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+&gsbi1_i2c {
+	clock-frequency = <200000>;
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+};
+
+&gsbi7 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi7_serial {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gsbi7_uart_2pins>;
+	status = "okay";
+};
+
+&pcie {
+	vdda-supply = <&pm8921_s3>;
+	vdda_phy-supply = <&pm8921_lvs6>;
+	vdda_refclk-supply = <&v3p3_fixed>;
+	pinctrl-0 = <&pcie_pins>;
+	pinctrl-names = "default";
+	perst-gpios = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&pm8821 {
+	interrupts-extended = <&tlmm_pinmux 76 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&pm8921 {
+	interrupts-extended = <&tlmm_pinmux 74 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&pm8921_gpio {
+	wlan_default_gpios: wlan-gpios-state {
+		pinconf {
+			pins = "gpio43";
+			function = "normal";
+			bias-disable;
+			power-source = <PM8921_GPIO_S4>;
+		};
+	};
+};
+
+&rpm {
+	regulators {
+		compatible = "qcom,rpm-pm8921-regulators";
+
+		vin_lvs1_3_6-supply = <&pm8921_s4>;
+		vin_lvs2-supply = <&pm8921_s1>;
+		vin_lvs4_5_7-supply = <&pm8921_s4>;
+
+		vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+		vdd_l24-supply = <&pm8921_s1>;
+		vdd_l25-supply = <&pm8921_s1>;
+		vdd_l26-supply = <&pm8921_s7>;
+		vdd_l27-supply = <&pm8921_s7>;
+		vdd_l28-supply = <&pm8921_s7>;
+
+		/* Buck SMPS */
+		pm8921_s1: s1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		pm8921_s3: s3 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1400000>;
+			qcom,switch-mode-frequency = <4800000>;
+		};
+
+		pm8921_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <3200000>;
+		};
+
+		pm8921_s7: s7 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <3200000>;
+		};
+
+		pm8921_l3: l3 {
+			regulator-min-microvolt = <3050000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+
+		pm8921_l4: l4 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l5: l5 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l23: l23 {
+			regulator-min-microvolt = <1700000>;
+			regulator-max-microvolt = <1900000>;
+			bias-pull-down;
+		};
+
+		pm8921_lvs6: lvs6 {
+			bias-pull-down;
+		};
+	};
+};
+
+/* eMMC */
+&sdcc1 {
+	vmmc-supply = <&pm8921_l5>;
+	vqmmc-supply = <&pm8921_s4>;
+	status = "okay";
+};
+
+/* External micro SD card */
+&sdcc3 {
+	vmmc-supply = <&v3p3_fixed>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&card_detect>;
+	cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+/* WLAN */
+&sdcc4 {
+	status = "okay";
+	vmmc-supply = <&v3p3_fixed>;
+	vqmmc-supply = <&v3p3_fixed>;
+	mmc-pwrseq = <&sdcc4_pwrseq>;
+};
+
+&tlmm_pinmux {
+	card_detect: card-detect-state {
+		pins = "gpio26";
+		function = "gpio";
+		bias-disable;
+	};
+
+	pcie_pins: pcie-state {
+		pins = "gpio27";
+		function = "gpio";
+		drive-strength = <12>;
+		bias-disable;
+	};
+};
+
+&usb_hs1_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l4>;
+};
+
+&usb_hs3_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l23>;
+};
+
+&usb_hs4_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l23>;
+};
+
+/* OTG */
+&usb1 {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb3 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb4 {
+	dr_mode = "host";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-ifc6410.dts
new file mode 100644
index 000000000000..717bfd74edb7
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-ifc6410.dts
@@ -0,0 +1,366 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+#include "qcom-apq8064-v2.0.dtsi"
+#include "pm8821.dtsi"
+#include "pm8921.dtsi"
+
+/ {
+	model = "Qualcomm APQ8064/IFC6410";
+	compatible = "qcom,apq8064-ifc6410", "qcom,apq8064";
+
+	aliases {
+		serial0 = &gsbi7_serial;
+		serial1 = &gsbi6_serial;
+		i2c0 = &gsbi1_i2c;
+		i2c1 = &gsbi2_i2c;
+		i2c2 = &gsbi3_i2c;
+		i2c3 = &gsbi4_i2c;
+		spi0 = &gsbi5_spi;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&notify_led>;
+
+		led-user1 {
+			label = "apq8064:green:user1";
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pm8921_gpio 18 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "d";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&hdmi_out>;
+			};
+		};
+	};
+
+	sdcc4_pwrseq: pwrseq-sdcc4 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_default_gpios>;
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pm8921_gpio 43 GPIO_ACTIVE_LOW>;
+	};
+
+	ext_3p3v: regulator-ext-3p3v {
+		compatible = "regulator-fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "ext_3p3v";
+		startup-delay-us = <0>;
+		gpio = <&tlmm_pinmux 77 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+};
+
+&gsbi1 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+&gsbi1_i2c {
+	clock-frequency = <200000>;
+	status = "okay";
+
+	eeprom@52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+		pagesize = <32>;
+	};
+};
+
+&gsbi3 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+&gsbi3_i2c {
+	status = "okay";
+};
+
+&gsbi4 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+/* CAM I2C MIPI-CSI connector */
+&gsbi4_i2c {
+	status = "okay";
+};
+
+&gsbi5 {
+	qcom,mode = <GSBI_PROT_SPI>;
+	status = "okay";
+};
+
+&gsbi5_spi {
+	num-cs = <1>;
+	cs-gpios = <&tlmm_pinmux 53 0>;
+	status = "okay";
+};
+
+&gsbi6 {
+	qcom,mode = <GSBI_PROT_UART_W_FC>;
+	status = "okay";
+};
+
+&gsbi6_serial {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gsbi6_uart_4pins>;
+	status = "okay";
+};
+
+&gsbi7 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi7_serial {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gsbi7_uart_2pins>;
+	status = "okay";
+};
+
+&hdmi {
+	core-vdda-supply = <&pm8921_hdmi_switch>;
+	status = "okay";
+};
+
+&hdmi_in {
+	remote-endpoint = <&mdp_dtv_out>;
+};
+
+&hdmi_out {
+	remote-endpoint = <&hdmi_con>;
+};
+
+&hdmi_phy {
+	status = "okay";
+	core-vdda-supply = <&pm8921_hdmi_switch>;
+};
+
+&mdp {
+	status = "okay";
+};
+
+&mdp_dtv_out {
+	remote-endpoint = <&hdmi_in>;
+};
+
+&pcie {
+	status = "okay";
+	vdda-supply = <&pm8921_s3>;
+	vdda_phy-supply = <&pm8921_lvs6>;
+	vdda_refclk-supply = <&ext_3p3v>;
+	pinctrl-0 = <&pcie_pins>;
+	pinctrl-names = "default";
+	perst-gpios = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
+};
+
+&pm8821 {
+	interrupts-extended = <&tlmm_pinmux 76 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&pm8921 {
+	interrupts-extended = <&tlmm_pinmux 74 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&pm8921_gpio {
+	wlan_default_gpios: wlan-gpios-state {
+		pinconf {
+			pins = "gpio43";
+			function = "normal";
+			bias-disable;
+			power-source = <PM8921_GPIO_S4>;
+		};
+	};
+
+	notify_led: nled-state {
+		pinconf {
+			pins = "gpio18";
+			function = "normal";
+			bias-disable;
+			power-source = <PM8921_GPIO_S4>;
+		};
+	};
+};
+
+&rpm {
+	regulators {
+		compatible = "qcom,rpm-pm8921-regulators";
+
+		vin_lvs1_3_6-supply = <&pm8921_s4>;
+		vin_lvs2-supply = <&pm8921_s1>;
+		vin_lvs4_5_7-supply = <&pm8921_s4>;
+
+		vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+		vdd_l24-supply = <&pm8921_s1>;
+		vdd_l25-supply = <&pm8921_s1>;
+		vdd_l26-supply = <&pm8921_s7>;
+		vdd_l27-supply = <&pm8921_s7>;
+		vdd_l28-supply = <&pm8921_s7>;
+
+		/* Buck SMPS */
+		pm8921_s1: s1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		pm8921_s3: s3 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1400000>;
+			qcom,switch-mode-frequency = <4800000>;
+		};
+
+		pm8921_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <3200000>;
+		};
+
+		pm8921_s7: s7 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <3200000>;
+		};
+
+		pm8921_l3: l3 {
+			regulator-min-microvolt = <3050000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+
+		pm8921_l4: l4 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l5: l5 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l6: l6 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l23: l23 {
+			regulator-min-microvolt = <1700000>;
+			regulator-max-microvolt = <1900000>;
+			bias-pull-down;
+		};
+
+		pm8921_lvs1: lvs1 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs6: lvs6 {
+			bias-pull-down;
+		};
+
+		pm8921_hdmi_switch: hdmi-switch {
+			bias-pull-down;
+		};
+	};
+};
+
+&sata_phy0 {
+	status = "okay";
+};
+
+&sata0 {
+	target-supply = <&pm8921_s4>;
+	status = "okay";
+};
+
+/* eMMC */
+&sdcc1 {
+	vmmc-supply = <&pm8921_l5>;
+	vqmmc-supply = <&pm8921_s4>;
+	status = "okay";
+};
+
+/* External micro SD card */
+&sdcc3 {
+	vmmc-supply = <&pm8921_l6>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&card_detect>;
+	cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+/* WLAN */
+&sdcc4 {
+	vmmc-supply = <&ext_3p3v>;
+	vqmmc-supply = <&pm8921_lvs1>;
+	mmc-pwrseq = <&sdcc4_pwrseq>;
+	status = "okay";
+};
+
+&tlmm_pinmux {
+	card_detect: card-detect-state {
+		pins = "gpio26";
+		function = "gpio";
+		bias-disable;
+	};
+
+	pcie_pins: pcie-state {
+		pins = "gpio27";
+		function = "gpio";
+		drive-strength = <12>;
+		bias-disable;
+	};
+};
+
+&usb_hs1_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l4>;
+};
+
+&usb_hs3_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l23>;
+};
+
+&usb_hs4_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l23>;
+};
+
+/* OTG */
+&usb1 {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb3 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb4 {
+	dr_mode = "host";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-lg-nexus4-mako.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-lg-nexus4-mako.dts
new file mode 100644
index 000000000000..fdbbc1389297
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-lg-nexus4-mako.dts
@@ -0,0 +1,359 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/mfd/qcom-rpm.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+#include "qcom-apq8064-v2.0.dtsi"
+#include "pm8821.dtsi"
+#include "pm8921.dtsi"
+
+/ {
+	model = "LG Nexus 4 (mako)";
+	compatible = "lg,nexus4-mako", "qcom,apq8064";
+	chassis-type = "handset";
+
+	aliases {
+		serial0 = &gsbi7_serial;
+		serial1 = &gsbi6_serial;
+		serial2 = &gsbi4_serial;
+	};
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+	};
+
+	battery_cell: battery-cell {
+		compatible = "simple-battery";
+		constant-charge-current-max-microamp = <900000>;
+		operating-range-celsius = <0 45>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		ramoops@88d00000 {
+			compatible = "ramoops";
+			reg = <0x88d00000 0x100000>;
+			record-size = <0x20000>;
+			console-size = <0x20000>;
+			ftrace-size = <0x20000>;
+		};
+	};
+};
+
+&gsbi1 {
+	qcom,mode = <GSBI_PROT_I2C>;
+
+	status = "okay";
+};
+
+&gsbi1_i2c {
+	clock-frequency = <200000>;
+
+	status = "okay";
+};
+
+&gsbi4 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+
+	status = "okay";
+};
+
+&gsbi4_serial {
+	status = "okay";
+};
+
+&pm8821 {
+	interrupts-extended = <&tlmm_pinmux 76 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&pm8921 {
+	interrupts-extended = <&tlmm_pinmux 74 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&pm8921_keypad {
+	linux,keymap = <
+		MATRIX_KEY(0, 0, KEY_VOLUMEDOWN)
+		MATRIX_KEY(0, 1, KEY_VOLUMEUP)
+	>;
+
+	keypad,num-rows = <1>;
+	keypad,num-columns = <5>;
+
+	status = "okay";
+};
+
+&riva {
+	pinctrl-names = "default";
+	pinctrl-0 = <&riva_wlan_pin_a>, <&riva_bt_pin_a>, <&riva_fm_pin_a>;
+
+	vddcx-supply = <&pm8921_s3>;
+	vddmx-supply = <&pm8921_l24>;
+	vddpx-supply = <&pm8921_s4>;
+
+	status = "okay";
+
+	iris {
+		vddxo-supply = <&pm8921_l4>;
+		vddrfa-supply = <&pm8921_s2>;
+		vddpa-supply = <&pm8921_l10>;
+		vdddig-supply = <&pm8921_lvs2>;
+	};
+};
+
+&rpm {
+	regulators {
+		compatible = "qcom,rpm-pm8921-regulators";
+
+		vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+		vdd_l24-supply = <&pm8921_s1>;
+		vdd_l25-supply = <&pm8921_s1>;
+		vdd_l26-supply = <&pm8921_s7>;
+		vdd_l27-supply = <&pm8921_s7>;
+		vdd_l28-supply = <&pm8921_s7>;
+		vin_lvs1_3_6-supply = <&pm8921_s4>;
+		vin_lvs2-supply = <&pm8921_s1>;
+		vin_lvs4_5_7-supply = <&pm8921_s4>;
+
+		pm8921_l1: l1 {
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+			regulator-always-on;
+			bias-pull-down;
+		};
+
+		/* mipi_dsi.1-dsi1_pll_vdda */
+		pm8921_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		/* msm_otg-HSUSB_3p3 */
+		pm8921_l3: l3 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3500000>;
+			bias-pull-down;
+		};
+
+		/* msm_otg-HSUSB_1p8 */
+		pm8921_l4: l4 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		/* msm_sdcc.1-sdc_vdd */
+		pm8921_l5: l5 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		/* earjack_debug */
+		pm8921_l6: l6 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		/* mipi_dsi.1-dsi_vci */
+		pm8921_l8: l8 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		/* wcnss_wlan.0-iris_vddpa */
+		pm8921_l10: l10 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <2900000>;
+			bias-pull-down;
+		};
+
+		/* mipi_dsi.1-dsi1_avdd */
+		pm8921_l11: l11 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+
+		/* touch_vdd */
+		pm8921_l15: l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		/* slimport_dvdd */
+		pm8921_l18: l18 {
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+			bias-pull-down;
+		};
+
+		/* touch_io */
+		pm8921_l22: l22 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		/*
+		 * mipi_dsi.1-dsi_vddio
+		 * pil_qdsp6v4.1-pll_vdd
+		 * pil_qdsp6v4.2-pll_vdd
+		 * msm_ehci_host.0-HSUSB_1p8
+		 * msm_ehci_host.1-HSUSB_1p8
+		 */
+		pm8921_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		/*
+		 * tabla2x-slim-CDC_VDDA_A_1P2V
+		 * tabla2x-slim-VDDD_CDC_D
+		 */
+		pm8921_l24: l24 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1150000>;
+			bias-pull-down;
+		};
+
+		pm8921_l25: l25 {
+			regulator-min-microvolt = <1250000>;
+			regulator-max-microvolt = <1250000>;
+			regulator-always-on;
+			bias-pull-down;
+		};
+
+		pm8921_l26: l26 {
+			regulator-min-microvolt = <375000>;
+			regulator-max-microvolt = <1050000>;
+			regulator-always-on;
+			bias-pull-down;
+		};
+
+		pm8921_l27: l27 {
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+		};
+
+		pm8921_l28: l28 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			bias-pull-down;
+		};
+
+		/* wcnss_wlan.0-iris_vddio */
+		pm8921_lvs1: lvs1 {
+			bias-pull-down;
+		};
+
+		/* wcnss_wlan.0-iris_vdddig */
+		pm8921_lvs2: lvs2 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs3: lvs3 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs4: lvs4 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs5: lvs5 {
+			bias-pull-down;
+		};
+
+		/* mipi_dsi.1-dsi_iovcc */
+		pm8921_lvs6: lvs6 {
+			bias-pull-down;
+		};
+
+		/*
+		 * pil_riva-pll_vdd
+		 * lvds.0-lvds_vdda
+		 * mipi_dsi.1-dsi1_vddio
+		 * hdmi_msm.0-hdmi_vdda
+		 */
+		pm8921_lvs7: lvs7 {
+			bias-pull-down;
+		};
+
+		pm8921_ncp: ncp {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+		};
+
+		/* Buck SMPS */
+		pm8921_s1: s1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		pm8921_s2: s2 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		/* msm otg HSUSB_VDDCX */
+		pm8921_s3: s3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <4800000>;
+			bias-pull-down;
+		};
+
+		/*
+		 * msm_sdcc.1-sdc-vdd_io
+		 * tabla2x-slim-CDC_VDDA_RX
+		 * tabla2x-slim-CDC_VDDA_TX
+		 * tabla2x-slim-CDC_VDD_CP
+		 * tabla2x-slim-VDDIO_CDC
+		 */
+		pm8921_s4: s4 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+			qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+		};
+
+		/*
+		 * supply vdd_l26, vdd_l27, vdd_l28
+		 */
+		pm8921_s7: s7 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <3200000>;
+		};
+
+		pm8921_s8: s8 {
+			regulator-min-microvolt = <2200000>;
+			regulator-max-microvolt = <2200000>;
+			qcom,switch-mode-frequency = <1600000>;
+		};
+	};
+};
+
+/* eMMC */
+&sdcc1 {
+	vmmc-supply = <&pm8921_l5>;
+	vqmmc-supply = <&pm8921_s4>;
+
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-pins.dtsi b/arch/arm/boot/dts/qcom/qcom-apq8064-pins.dtsi
new file mode 100644
index 000000000000..e53de709e9d1
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-pins.dtsi
@@ -0,0 +1,243 @@
+// SPDX-License-Identifier: GPL-2.0
+
+&tlmm_pinmux {
+	sdcc1_default_state: sdcc1-default-state {
+		clk-pins {
+			pins = "sdc1_clk";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		cmd-pins {
+			pins = "sdc1_cmd";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+
+		data-pins {
+			pins = "sdc1_data";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	sdcc3_default_state: sdcc3-default-state {
+		clk-pins {
+			pins = "sdc3_clk";
+			drive-strength = <8>;
+			bias-disable;
+		};
+
+		cmd-pins {
+			pins = "sdc3_cmd";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		data-pins {
+			pins = "sdc3_data";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	sdc4_default_state: sdc4-default-state {
+		pins = "gpio63", "gpio64", "gpio65", "gpio66", "gpio67", "gpio68";
+		function = "sdc4";
+	};
+
+	gsbi1_uart_2pins: gsbi1-uart-2pins-state {
+		pins = "gpio18", "gpio19";
+		function = "gsbi1";
+	};
+
+	gsbi1_uart_4pins: gsbi1-uart-4pins-state {
+		pins = "gpio18", "gpio19", "gpio20", "gpio21";
+		function = "gsbi1";
+	};
+
+	gsbi4_uart_pin_a: gsbi4-uart-pin-active-state {
+		rx-pins {
+			pins = "gpio11";
+			function = "gsbi4";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		tx-pins {
+			pins = "gpio10";
+			function = "gsbi4";
+			drive-strength = <4>;
+			bias-disable;
+		};
+	};
+
+	gsbi6_uart_2pins: gsbi6-uart-2pins-state {
+		pins = "gpio14", "gpio15";
+		function = "gsbi6";
+	};
+
+	gsbi6_uart_4pins: gsbi6-uart-4pins-state {
+		pins = "gpio14", "gpio15", "gpio16", "gpio17";
+		function = "gsbi6";
+	};
+
+	gsbi7_uart_2pins: gsbi7-uart-2pins-state {
+		pins = "gpio82", "gpio83";
+		function = "gsbi7";
+	};
+
+	gsbi7_uart_4pins: gsbi7_uart_4pins-state {
+		pins = "gpio82", "gpio83", "gpio84", "gpio85";
+		function = "gsbi7";
+	};
+
+	i2c1_default_state: i2c1-default-state {
+		pins = "gpio20", "gpio21";
+		function = "gsbi1";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	i2c1_sleep_state: i2c1-sleep-state {
+		pins = "gpio20", "gpio21";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	i2c2_default_state: i2c2-default-state {
+		pins = "gpio24", "gpio25";
+		function = "gsbi2";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	i2c2_sleep_state: i2c2-sleep-state {
+		pins = "gpio24", "gpio25";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	i2c3_default_state: i2c3-default-state {
+		pins = "gpio8", "gpio9";
+		function = "gsbi3";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	i2c3_sleep_state: i2c3-sleep-state {
+		pins = "gpio8", "gpio9";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	i2c4_default_state: i2c4-default-state {
+		pins = "gpio12", "gpio13";
+		function = "gsbi4";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	i2c4_sleep_state: i2c4-sleep-state {
+		pins = "gpio12", "gpio13";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	i2c6_default_state: i2c6-default-state {
+		pins = "gpio16", "gpio17";
+		function = "gsbi6";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	i2c6_sleep_state: i2c6-sleep-state {
+		pins = "gpio16", "gpio17";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	i2c7_default_state: i2c7-default-state {
+		pins = "gpio84", "gpio85";
+		function = "gsbi7";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	i2c7_sleep_state: i2c7-sleep-state {
+		pins = "gpio84", "gpio85";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	spi5_default_state: spi5-default-state {
+		spi5-pins {
+			pins = "gpio51", "gpio52", "gpio54";
+			function = "gsbi5";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		spi5-cs-pins {
+			pins = "gpio53";
+			function = "gpio";
+			drive-strength = <16>;
+			bias-disable;
+			output-high;
+		};
+	};
+
+	spi5_sleep_state: spi5-sleep-state {
+		spi5-pins {
+			pins = "gpio51", "gpio52", "gpio53", "gpio54";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+
+	riva_fm_pin_a: riva-fm-active-state {
+		pins = "gpio14", "gpio15";
+		function = "riva_fm";
+	};
+
+	riva_bt_pin_a: riva-bt-active-state {
+		pins = "gpio16", "gpio17";
+		function = "riva_bt";
+	};
+
+	riva_wlan_pin_a: riva-wlan-active-state {
+		pins = "gpio64", "gpio65", "gpio66", "gpio67", "gpio68";
+		function = "riva_wlan";
+
+		drive-strength = <6>;
+		bias-pull-down;
+	};
+
+	hdmi_pinctrl: hdmi-pinctrl-state {
+		ddc-pins {
+			pins = "gpio70", "gpio71";
+			function = "hdmi";
+			bias-pull-up;
+			drive-strength = <2>;
+		};
+
+		hpd-pins {
+			pins = "gpio72";
+			function = "hdmi";
+			bias-pull-down;
+			drive-strength = <16>;
+		};
+	};
+
+	ps_hold_default_state: ps-hold-default-state {
+		pins = "gpio78";
+		function = "ps_hold";
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8064-sony-xperia-lagan-yuga.dts b/arch/arm/boot/dts/qcom/qcom-apq8064-sony-xperia-lagan-yuga.dts
new file mode 100644
index 000000000000..7752f07973f9
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-sony-xperia-lagan-yuga.dts
@@ -0,0 +1,416 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/mfd/qcom-rpm.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+#include "qcom-apq8064-v2.0.dtsi"
+#include "pm8821.dtsi"
+#include "pm8921.dtsi"
+
+/ {
+	model = "Sony Xperia Z";
+	compatible = "sony,xperia-yuga", "qcom,apq8064";
+	chassis-type = "handset";
+
+	aliases {
+		serial0 = &gsbi5_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pin_a>;
+
+		key-camera-focus {
+			label = "camera_focus";
+			gpios = <&pm8921_gpio 3 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_CAMERA_FOCUS>;
+		};
+
+		key-camera-snapshot {
+			label = "camera_snapshot";
+			gpios = <&pm8921_gpio 4 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_CAMERA>;
+		};
+
+		key-volume-down {
+			label = "volume_down";
+			gpios = <&pm8921_gpio 29 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+
+		key-volume-up {
+			label = "volume_up";
+			gpios = <&pm8921_gpio 35 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+	};
+};
+
+&gsbi5 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi5_serial {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gsbi5_uart_pin_a>;
+	status = "okay";
+};
+
+&pm8821 {
+	interrupts-extended = <&tlmm_pinmux 76 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&pm8921 {
+	interrupts-extended = <&tlmm_pinmux 74 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&pm8921_gpio {
+	gpio_keys_pin_a: gpio-keys-active-state {
+		pins = "gpio3", "gpio4", "gpio29", "gpio35";
+		function = "normal";
+
+		bias-pull-up;
+		drive-push-pull;
+		input-enable;
+		power-source = <2>;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+		qcom,pull-up-strength = <0>;
+	};
+};
+
+&riva {
+	pinctrl-names = "default";
+	pinctrl-0 = <&riva_wlan_pin_a>, <&riva_bt_pin_a>, <&riva_fm_pin_a>;
+
+	vddcx-supply = <&pm8921_s3>;
+	vddmx-supply = <&pm8921_l24>;
+	vddpx-supply = <&pm8921_s4>;
+
+	status = "okay";
+
+	iris {
+		vddxo-supply = <&pm8921_l4>;
+		vddrfa-supply = <&pm8921_s2>;
+		vddpa-supply = <&pm8921_l10>;
+		vdddig-supply = <&pm8921_lvs2>;
+	};
+};
+
+&rpm {
+	regulators {
+		compatible = "qcom,rpm-pm8921-regulators";
+
+		vin_l1_l2_l12_l18-supply = <&pm8921_s4>;
+		vin_lvs_1_3_6-supply = <&pm8921_s4>;
+		vin_lvs_4_5_7-supply = <&pm8921_s4>;
+		vin_ncp-supply = <&pm8921_l6>;
+		vin_lvs2-supply = <&pm8921_s4>;
+		vin_l24-supply = <&pm8921_s1>;
+		vin_l25-supply = <&pm8921_s1>;
+		vin_l27-supply = <&pm8921_s7>;
+		vin_l28-supply = <&pm8921_s7>;
+
+		/* Buck SMPS */
+		pm8921_s1: s1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		pm8921_s2: s2 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8921_s3: s3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <4800000>;
+			bias-pull-down;
+		};
+
+		pm8921_s4: s4 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+			qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+		};
+
+		pm8921_s7: s7 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <3200000>;
+		};
+
+		pm8921_s8: s8 {
+			regulator-min-microvolt = <2200000>;
+			regulator-max-microvolt = <2200000>;
+			qcom,switch-mode-frequency = <1600000>;
+		};
+
+		/* PMOS LDO */
+		pm8921_l1: l1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+			bias-pull-down;
+		};
+
+		pm8921_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8921_l3: l3 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			bias-pull-down;
+		};
+
+		pm8921_l4: l4 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l5: l5 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l6: l6 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l7: l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l8: l8 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l9: l9 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l10: l10 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <2900000>;
+			bias-pull-down;
+		};
+
+		pm8921_l11: l11 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l12: l12 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8921_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l15: l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l16: l16 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l17: l17 {
+			regulator-min-microvolt = <2000000>;
+			regulator-max-microvolt = <2000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l18: l18 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8921_l21: l21 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			bias-pull-down;
+		};
+
+		pm8921_l22: l22 {
+			regulator-min-microvolt = <2600000>;
+			regulator-max-microvolt = <2600000>;
+			bias-pull-down;
+		};
+
+		pm8921_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l24: l24 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1150000>;
+			bias-pull-down;
+		};
+
+		pm8921_l25: l25 {
+			regulator-always-on;
+			regulator-min-microvolt = <1250000>;
+			regulator-max-microvolt = <1250000>;
+			bias-pull-down;
+		};
+
+		pm8921_l27: l27 {
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+		};
+
+		pm8921_l28: l28 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			bias-pull-down;
+		};
+
+		pm8921_l29: l29 {
+			regulator-min-microvolt = <2000000>;
+			regulator-max-microvolt = <2000000>;
+			bias-pull-down;
+		};
+
+		/* Low Voltage Switch */
+		pm8921_lvs1: lvs1 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs2: lvs2 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs3: lvs3 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs4: lvs4 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs5: lvs5 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs6: lvs6 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs7: lvs7 {
+			bias-pull-down;
+		};
+
+		pm8921_usb_switch: usb-switch {};
+
+		pm8921_hdmi_switch: hdmi-switch {
+			bias-pull-down;
+		};
+
+		pm8921_ncp: ncp {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+		};
+	};
+};
+
+&sdcc1 {
+	vmmc-supply = <&pm8921_l5>;
+	vqmmc-supply = <&pm8921_s4>;
+	status = "okay";
+};
+
+&sdcc3 {
+	vmmc-supply = <&pm8921_l6>;
+	cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdcc3_default_state>, <&sdcc3_cd_pin_a>;
+
+	status = "okay";
+};
+
+&tlmm_pinmux {
+	gsbi5_uart_pin_a: gsbi5-uart-pin-active-state {
+		rx-pins {
+			pins = "gpio52";
+			function = "gsbi5";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		tx-pins {
+			pins = "gpio51";
+			function = "gsbi5";
+			drive-strength = <4>;
+			bias-disable;
+		};
+	};
+
+
+	sdcc3_cd_pin_a: sdcc3-cd-pin-active-state {
+		pins = "gpio26";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&usb_hs1_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l4>;
+};
+
+&usb1 {
+	dr_mode = "otg";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom-apq8064-v2.0.dtsi b/arch/arm/boot/dts/qcom/qcom-apq8064-v2.0.dtsi
index 46ed48f0244f..46ed48f0244f 100644
--- a/arch/arm/boot/dts/qcom-apq8064-v2.0.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064-v2.0.dtsi
diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
index a1c8ae516d21..09062b2ad8ba 100644
--- a/arch/arm/boot/dts/qcom-apq8064.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-apq8064.dtsi
@@ -2,6 +2,7 @@
 /dts-v1/;
 
 #include <dt-bindings/clock/qcom,gcc-msm8960.h>
+#include <dt-bindings/clock/qcom,lcc-msm8960.h>
 #include <dt-bindings/reset/qcom,gcc-msm8960.h>
 #include <dt-bindings/clock/qcom,mmcc-msm8960.h>
 #include <dt-bindings/clock/qcom,rpmcc.h>
@@ -35,57 +36,58 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		CPU0: cpu@0 {
+		cpu0: cpu@0 {
 			compatible = "qcom,krait";
 			enable-method = "qcom,kpss-acc-v1";
 			device_type = "cpu";
 			reg = <0>;
-			next-level-cache = <&L2>;
+			next-level-cache = <&l2>;
 			qcom,acc = <&acc0>;
 			qcom,saw = <&saw0>;
-			cpu-idle-states = <&CPU_SPC>;
+			cpu-idle-states = <&cpu_spc>;
 		};
 
-		CPU1: cpu@1 {
+		cpu1: cpu@1 {
 			compatible = "qcom,krait";
 			enable-method = "qcom,kpss-acc-v1";
 			device_type = "cpu";
 			reg = <1>;
-			next-level-cache = <&L2>;
+			next-level-cache = <&l2>;
 			qcom,acc = <&acc1>;
 			qcom,saw = <&saw1>;
-			cpu-idle-states = <&CPU_SPC>;
+			cpu-idle-states = <&cpu_spc>;
 		};
 
-		CPU2: cpu@2 {
+		cpu2: cpu@2 {
 			compatible = "qcom,krait";
 			enable-method = "qcom,kpss-acc-v1";
 			device_type = "cpu";
 			reg = <2>;
-			next-level-cache = <&L2>;
+			next-level-cache = <&l2>;
 			qcom,acc = <&acc2>;
 			qcom,saw = <&saw2>;
-			cpu-idle-states = <&CPU_SPC>;
+			cpu-idle-states = <&cpu_spc>;
 		};
 
-		CPU3: cpu@3 {
+		cpu3: cpu@3 {
 			compatible = "qcom,krait";
 			enable-method = "qcom,kpss-acc-v1";
 			device_type = "cpu";
 			reg = <3>;
-			next-level-cache = <&L2>;
+			next-level-cache = <&l2>;
 			qcom,acc = <&acc3>;
 			qcom,saw = <&saw3>;
-			cpu-idle-states = <&CPU_SPC>;
+			cpu-idle-states = <&cpu_spc>;
 		};
 
-		L2: l2-cache {
+		l2: l2-cache {
 			compatible = "cache";
 			cache-level = <2>;
+			cache-unified;
 		};
 
 		idle-states {
-			CPU_SPC: spc {
+			cpu_spc: cpu-spc {
 				compatible = "qcom,idle-state-spc",
 						"arm,idle-state";
 				entry-latency-us = <400>;
@@ -105,7 +107,7 @@
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
-			thermal-sensors = <&gcc 7>;
+			thermal-sensors = <&tsens 7>;
 			coefficients = <1199 0>;
 
 			trips {
@@ -126,7 +128,7 @@
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
-			thermal-sensors = <&gcc 8>;
+			thermal-sensors = <&tsens 8>;
 			coefficients = <1132 0>;
 
 			trips {
@@ -147,7 +149,7 @@
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
-			thermal-sensors = <&gcc 9>;
+			thermal-sensors = <&tsens 9>;
 			coefficients = <1199 0>;
 
 			trips {
@@ -168,7 +170,7 @@
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
-			thermal-sensors = <&gcc 10>;
+			thermal-sensors = <&tsens 10>;
 			coefficients = <1132 0>;
 
 			trips {
@@ -188,7 +190,7 @@
 
 	cpu-pmu {
 		compatible = "qcom,krait-pmu";
-		interrupts = <1 10 0x304>;
+		interrupts = <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
 	};
 
 	clocks {
@@ -211,12 +213,6 @@
 		};
 	};
 
-	sfpb_mutex: hwmutex {
-		compatible = "qcom,sfpb-mutex";
-		syscon = <&sfpb_wrapper_mutex 0x604 0x4>;
-		#hwlock-cells = <1>;
-	};
-
 	smem {
 		compatible = "qcom,smem";
 		memory-region = <&smem_region>;
@@ -224,46 +220,6 @@
 		hwlocks = <&sfpb_mutex 3>;
 	};
 
-	smd {
-		compatible = "qcom,smd";
-
-		modem@0 {
-			interrupts = <0 37 IRQ_TYPE_EDGE_RISING>;
-
-			qcom,ipc = <&l2cc 8 3>;
-			qcom,smd-edge = <0>;
-
-			status = "disabled";
-		};
-
-		q6@1 {
-			interrupts = <0 90 IRQ_TYPE_EDGE_RISING>;
-
-			qcom,ipc = <&l2cc 8 15>;
-			qcom,smd-edge = <1>;
-
-			status = "disabled";
-		};
-
-		dsps@3 {
-			interrupts = <0 138 IRQ_TYPE_EDGE_RISING>;
-
-			qcom,ipc = <&sps_sic_non_secure 0x4080 0>;
-			qcom,smd-edge = <3>;
-
-			status = "disabled";
-		};
-
-		riva@6 {
-			interrupts = <0 198 IRQ_TYPE_EDGE_RISING>;
-
-			qcom,ipc = <&l2cc 8 25>;
-			qcom,smd-edge = <6>;
-
-			status = "disabled";
-		};
-	};
-
 	smsm {
 		compatible = "qcom,smsm";
 
@@ -282,7 +238,7 @@
 
 		modem_smsm: modem@1 {
 			reg = <1>;
-			interrupts = <0 38 IRQ_TYPE_EDGE_RISING>;
+			interrupts = <GIC_SPI 38 IRQ_TYPE_EDGE_RISING>;
 
 			interrupt-controller;
 			#interrupt-cells = <2>;
@@ -290,7 +246,7 @@
 
 		q6_smsm: q6@2 {
 			reg = <2>;
-			interrupts = <0 89 IRQ_TYPE_EDGE_RISING>;
+			interrupts = <GIC_SPI 89 IRQ_TYPE_EDGE_RISING>;
 
 			interrupt-controller;
 			#interrupt-cells = <2>;
@@ -298,7 +254,7 @@
 
 		wcnss_smsm: wcnss@3 {
 			reg = <3>;
-			interrupts = <0 204 IRQ_TYPE_EDGE_RISING>;
+			interrupts = <GIC_SPI 204 IRQ_TYPE_EDGE_RISING>;
 
 			interrupt-controller;
 			#interrupt-cells = <2>;
@@ -306,7 +262,7 @@
 
 		dsps_smsm: dsps@4 {
 			reg = <4>;
-			interrupts = <0 137 IRQ_TYPE_EDGE_RISING>;
+			interrupts = <GIC_SPI 137 IRQ_TYPE_EDGE_RISING>;
 
 			interrupt-controller;
 			#interrupt-cells = <2>;
@@ -315,28 +271,45 @@
 
 	firmware {
 		scm {
-			compatible = "qcom,scm-apq8064";
+			compatible = "qcom,scm-apq8064", "qcom,scm";
 
 			clocks = <&rpmcc RPM_DAYTONA_FABRIC_CLK>;
 			clock-names = "core";
 		};
 	};
 
+	replicator {
+		compatible = "arm,coresight-static-replicator";
+
+		clocks = <&rpmcc RPM_QDSS_CLK>;
+		clock-names = "apb_pclk";
+
+		in-ports {
+			port {
+				replicator_in: endpoint {
+					remote-endpoint = <&funnel_out>;
+				};
+			};
+		};
+
+		out-ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				replicator_out0: endpoint {
+					remote-endpoint = <&etb_in>;
+				};
+			};
 
-	/*
-	 * These channels from the ADC are simply hardware monitors.
-	 * That is why the ADC is referred to as "HKADC" - HouseKeeping
-	 * ADC.
-	 */
-	iio-hwmon {
-		compatible = "iio-hwmon";
-		io-channels = <&xoadc 0x00 0x01>, /* Battery */
-			    <&xoadc 0x00 0x02>, /* DC in (charger) */
-			    <&xoadc 0x00 0x04>, /* VPH the main system voltage */
-			    <&xoadc 0x00 0x0b>, /* Die temperature */
-			    <&xoadc 0x00 0x0c>, /* Reference voltage 1.25V */
-			    <&xoadc 0x00 0x0d>, /* Reference voltage 0.625V */
-			    <&xoadc 0x00 0x0e>; /* Charger temperature */
+			port@1 {
+				reg = <1>;
+				replicator_out1: endpoint {
+					remote-endpoint = <&tpiu_in>;
+				};
+			};
+		};
 	};
 
 	soc: soc {
@@ -354,84 +327,119 @@
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
-			interrupts = <0 16 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
 
 			pinctrl-names = "default";
-			pinctrl-0 = <&ps_hold>;
+			pinctrl-0 = <&ps_hold_default_state>;
 		};
 
-		sfpb_wrapper_mutex: syscon@1200000 {
-			compatible = "syscon";
-			reg = <0x01200000 0x8000>;
+		sfpb_mutex: hwmutex@1200600 {
+			compatible = "qcom,sfpb-mutex";
+			reg = <0x01200600 0x100>;
+			#hwlock-cells = <1>;
 		};
 
 		intc: interrupt-controller@2000000 {
 			compatible = "qcom,msm-qgic2";
 			interrupt-controller;
+			#address-cells = <0>;
 			#interrupt-cells = <3>;
 			reg = <0x02000000 0x1000>,
 			      <0x02002000 0x1000>;
 		};
 
 		timer@200a000 {
-			compatible = "qcom,kpss-timer",
-				     "qcom,kpss-wdt-apq8064", "qcom,msm-timer";
-			interrupts = <1 1 0x301>,
-				     <1 2 0x301>,
-				     <1 3 0x301>;
+			compatible = "qcom,kpss-wdt-apq8064", "qcom,kpss-timer",
+				     "qcom,msm-timer";
+			interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_EDGE_RISING)>,
+				     <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_EDGE_RISING)>,
+				     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_EDGE_RISING)>;
 			reg = <0x0200a000 0x100>;
-			clock-frequency = <27000000>,
-					  <32768>;
+			clock-frequency = <27000000>;
+			clocks = <&sleep_clk>;
+			clock-names = "sleep";
 			cpu-offset = <0x80000>;
 		};
 
 		acc0: clock-controller@2088000 {
 			compatible = "qcom,kpss-acc-v1";
 			reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			clock-output-names = "acpu0_aux";
+			#clock-cells = <0>;
 		};
 
 		acc1: clock-controller@2098000 {
 			compatible = "qcom,kpss-acc-v1";
 			reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			clock-output-names = "acpu1_aux";
+			#clock-cells = <0>;
 		};
 
 		acc2: clock-controller@20a8000 {
 			compatible = "qcom,kpss-acc-v1";
 			reg = <0x020a8000 0x1000>, <0x02008000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			clock-output-names = "acpu2_aux";
+			#clock-cells = <0>;
 		};
 
 		acc3: clock-controller@20b8000 {
 			compatible = "qcom,kpss-acc-v1";
 			reg = <0x020b8000 0x1000>, <0x02008000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			clock-output-names = "acpu3_aux";
+			#clock-cells = <0>;
 		};
 
-		saw0: power-controller@2089000 {
+		saw0: power-manager@2089000 {
 			compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
 			reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
-			regulator;
+
+			saw0_vreg: regulator {
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1300000>;
+			};
 		};
 
-		saw1: power-controller@2099000 {
+		saw1: power-manager@2099000 {
 			compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
 			reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
-			regulator;
+
+			saw1_vreg: regulator {
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1300000>;
+			};
 		};
 
-		saw2: power-controller@20a9000 {
+		saw2: power-manager@20a9000 {
 			compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
 			reg = <0x020a9000 0x1000>, <0x02009000 0x1000>;
-			regulator;
+
+			saw2_vreg: regulator {
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1300000>;
+			};
 		};
 
-		saw3: power-controller@20b9000 {
+		saw3: power-manager@20b9000 {
 			compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
 			reg = <0x020b9000 0x1000>, <0x02009000 0x1000>;
-			regulator;
+
+			saw3_vreg: regulator {
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1300000>;
+			};
 		};
 
-		sps_sic_non_secure: sps-sic-non-secure@12100000 {
-			compatible	= "syscon";
-			reg		= <0x12100000 0x10000>;
+		sps_sic_non_secure: interrupt-controller@12100000 {
+			compatible = "qcom,apq8064-sps-sic", "syscon";
+			reg = <0x12100000 0x10000>;
 		};
 
 		gsbi1: gsbi@12440000 {
@@ -451,7 +459,7 @@
 				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
 				reg = <0x12450000 0x100>,
 				      <0x12400000 0x03>;
-				interrupts = <0 193 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&gcc GSBI1_UART_CLK>, <&gcc GSBI1_H_CLK>;
 				clock-names = "core", "iface";
 				status = "disabled";
@@ -459,11 +467,11 @@
 
 			gsbi1_i2c: i2c@12460000 {
 				compatible = "qcom,i2c-qup-v1.1.1";
-				pinctrl-0 = <&i2c1_pins>;
-				pinctrl-1 = <&i2c1_pins_sleep>;
+				pinctrl-0 = <&i2c1_default_state>;
+				pinctrl-1 = <&i2c1_sleep_state>;
 				pinctrl-names = "default", "sleep";
 				reg = <0x12460000 0x1000>;
-				interrupts = <0 194 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>;
 				clock-names = "core", "iface";
 				#address-cells = <1>;
@@ -489,10 +497,10 @@
 			gsbi2_i2c: i2c@124a0000 {
 				compatible = "qcom,i2c-qup-v1.1.1";
 				reg = <0x124a0000 0x1000>;
-				pinctrl-0 = <&i2c2_pins>;
-				pinctrl-1 = <&i2c2_pins_sleep>;
+				pinctrl-0 = <&i2c2_default_state>;
+				pinctrl-1 = <&i2c2_sleep_state>;
 				pinctrl-names = "default", "sleep";
-				interrupts = <0 196 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>;
 				clock-names = "core", "iface";
 				#address-cells = <1>;
@@ -513,8 +521,8 @@
 			ranges;
 			gsbi3_i2c: i2c@16280000 {
 				compatible = "qcom,i2c-qup-v1.1.1";
-				pinctrl-0 = <&i2c3_pins>;
-				pinctrl-1 = <&i2c3_pins_sleep>;
+				pinctrl-0 = <&i2c3_default_state>;
+				pinctrl-1 = <&i2c3_sleep_state>;
 				pinctrl-names = "default", "sleep";
 				reg = <0x16280000 0x1000>;
 				interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
@@ -538,10 +546,22 @@
 			#size-cells = <1>;
 			ranges;
 
+			gsbi4_serial: serial@16340000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x16340000 0x100>,
+				      <0x16300000 0x3>;
+				interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-0 = <&gsbi4_uart_pin_a>;
+				pinctrl-names = "default";
+				clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+
 			gsbi4_i2c: i2c@16380000 {
 				compatible = "qcom,i2c-qup-v1.1.1";
-				pinctrl-0 = <&i2c4_pins>;
-				pinctrl-1 = <&i2c4_pins_sleep>;
+				pinctrl-0 = <&i2c4_default_state>;
+				pinctrl-1 = <&i2c4_sleep_state>;
 				pinctrl-names = "default", "sleep";
 				reg = <0x16380000 0x1000>;
 				interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
@@ -567,7 +587,7 @@
 				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
 				reg = <0x1a240000 0x100>,
 				      <0x1a200000 0x03>;
-				interrupts = <0 154 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
 				clock-names = "core", "iface";
 				status = "disabled";
@@ -576,9 +596,9 @@
 			gsbi5_spi: spi@1a280000 {
 				compatible = "qcom,spi-qup-v1.1.1";
 				reg = <0x1a280000 0x1000>;
-				interrupts = <0 155 IRQ_TYPE_LEVEL_HIGH>;
-				pinctrl-0 = <&spi5_default>;
-				pinctrl-1 = <&spi5_sleep>;
+				interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-0 = <&spi5_default_state>;
+				pinctrl-1 = <&spi5_sleep_state>;
 				pinctrl-names = "default", "sleep";
 				clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
 				clock-names = "core", "iface";
@@ -603,7 +623,7 @@
 				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
 				reg = <0x16540000 0x100>,
 				      <0x16500000 0x03>;
-				interrupts = <0 156 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&gcc GSBI6_UART_CLK>, <&gcc GSBI6_H_CLK>;
 				clock-names = "core", "iface";
 				status = "disabled";
@@ -611,8 +631,8 @@
 
 			gsbi6_i2c: i2c@16580000 {
 				compatible = "qcom,i2c-qup-v1.1.1";
-				pinctrl-0 = <&i2c6_pins>;
-				pinctrl-1 = <&i2c6_pins_sleep>;
+				pinctrl-0 = <&i2c6_default_state>;
+				pinctrl-1 = <&i2c6_sleep_state>;
 				pinctrl-names = "default", "sleep";
 				reg = <0x16580000 0x1000>;
 				interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
@@ -639,7 +659,7 @@
 				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
 				reg = <0x16640000 0x1000>,
 				      <0x16600000 0x1000>;
-				interrupts = <0 158 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>;
 				clock-names = "core", "iface";
 				status = "disabled";
@@ -647,8 +667,8 @@
 
 			gsbi7_i2c: i2c@16680000 {
 				compatible = "qcom,i2c-qup-v1.1.1";
-				pinctrl-0 = <&i2c7_pins>;
-				pinctrl-1 = <&i2c7_pins_sleep>;
+				pinctrl-0 = <&i2c7_default_state>;
+				pinctrl-1 = <&i2c7_sleep_state>;
 				pinctrl-names = "default", "sleep";
 				reg = <0x16680000 0x1000>;
 				interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
@@ -666,158 +686,53 @@
 			clock-names = "core";
 		};
 
-		ssbi@c00000 {
+		ssbi2: ssbi@c00000 {
 			compatible = "qcom,ssbi";
 			reg = <0x00c00000 0x1000>;
 			qcom,controller-type = "pmic-arbiter";
-
-			pm8821: pmic@1 {
-				compatible = "qcom,pm8821";
-				interrupt-parent = <&tlmm_pinmux>;
-				interrupts = <76 IRQ_TYPE_LEVEL_LOW>;
-				#interrupt-cells = <2>;
-				interrupt-controller;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				pm8821_mpps: mpps@50 {
-					compatible = "qcom,pm8821-mpp", "qcom,ssbi-mpp";
-					reg = <0x50>;
-					interrupt-controller;
-					#interrupt-cells = <2>;
-					gpio-controller;
-					#gpio-cells = <2>;
-					gpio-ranges = <&pm8821_mpps 0 0 4>;
-				};
-			};
 		};
 
-		qcom,ssbi@500000 {
+		ssbi: ssbi@500000 {
 			compatible = "qcom,ssbi";
 			reg = <0x00500000 0x1000>;
 			qcom,controller-type = "pmic-arbiter";
-
-			pmicintc: pmic@0 {
-				compatible = "qcom,pm8921";
-				interrupt-parent = <&tlmm_pinmux>;
-				interrupts = <74 8>;
-				#interrupt-cells = <2>;
-				interrupt-controller;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				pm8921_gpio: gpio@150 {
-
-					compatible = "qcom,pm8921-gpio",
-						     "qcom,ssbi-gpio";
-					reg = <0x150>;
-					interrupt-controller;
-					#interrupt-cells = <2>;
-					gpio-controller;
-					gpio-ranges = <&pm8921_gpio 0 0 44>;
-					#gpio-cells = <2>;
-
-				};
-
-				pm8921_mpps: mpps@50 {
-					compatible = "qcom,pm8921-mpp",
-						     "qcom,ssbi-mpp";
-					reg = <0x50>;
-					gpio-controller;
-					#gpio-cells = <2>;
-					gpio-ranges = <&pm8921_mpps 0 0 12>;
-					interrupt-controller;
-					#interrupt-cells = <2>;
-				};
-
-				rtc@11d {
-					compatible = "qcom,pm8921-rtc";
-					interrupt-parent = <&pmicintc>;
-					interrupts = <39 1>;
-					reg = <0x11d>;
-					allow-set-time;
-				};
-
-				pwrkey@1c {
-					compatible = "qcom,pm8921-pwrkey";
-					reg = <0x1c>;
-					interrupt-parent = <&pmicintc>;
-					interrupts = <50 1>, <51 1>;
-					debounce = <15625>;
-					pull-up;
-				};
-
-				xoadc: xoadc@197 {
-					compatible = "qcom,pm8921-adc";
-					reg = <197>;
-					interrupts-extended = <&pmicintc 78 IRQ_TYPE_EDGE_RISING>;
-					#address-cells = <2>;
-					#size-cells = <0>;
-					#io-channel-cells = <2>;
-
-					vcoin: adc-channel@0 {
-						reg = <0x00 0x00>;
-					};
-					vbat: adc-channel@1 {
-						reg = <0x00 0x01>;
-					};
-					dcin: adc-channel@2 {
-						reg = <0x00 0x02>;
-					};
-					vph_pwr: adc-channel@4 {
-						reg = <0x00 0x04>;
-					};
-					batt_therm: adc-channel@8 {
-						reg = <0x00 0x08>;
-					};
-					batt_id: adc-channel@9 {
-						reg = <0x00 0x09>;
-					};
-					usb_vbus: adc-channel@a {
-						reg = <0x00 0x0a>;
-					};
-					die_temp: adc-channel@b {
-						reg = <0x00 0x0b>;
-					};
-					ref_625mv: adc-channel@c {
-						reg = <0x00 0x0c>;
-					};
-					ref_1250mv: adc-channel@d {
-						reg = <0x00 0x0d>;
-					};
-					chg_temp: adc-channel@e {
-						reg = <0x00 0x0e>;
-					};
-					ref_muxoff: adc-channel@f {
-						reg = <0x00 0x0f>;
-					};
-				};
-			};
 		};
 
-		qfprom: qfprom@700000 {
-			compatible	= "qcom,qfprom";
-			reg		= <0x00700000 0x1000>;
-			#address-cells	= <1>;
-			#size-cells	= <1>;
-			ranges;
-			tsens_calib: calib {
+		qfprom: efuse@700000 {
+			compatible = "qcom,apq8064-qfprom", "qcom,qfprom";
+			reg = <0x00700000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			tsens_calib: calib@404 {
 				reg = <0x404 0x10>;
 			};
-			tsens_backup: backup_calib {
+			tsens_backup: backup-calib@414 {
 				reg = <0x414 0x10>;
 			};
 		};
 
 		gcc: clock-controller@900000 {
-			compatible = "qcom,gcc-apq8064";
+			compatible = "qcom,gcc-apq8064", "syscon";
 			reg = <0x00900000 0x4000>;
-			nvmem-cells = <&tsens_calib>, <&tsens_backup>;
-			nvmem-cell-names = "calib", "calib_backup";
 			#clock-cells = <1>;
-			#power-domain-cells = <1>;
 			#reset-cells = <1>;
-			#thermal-sensor-cells = <1>;
+			clocks = <&cxo_board>,
+				 <&pxo_board>,
+				 <&lcc PLL4>;
+			clock-names = "cxo", "pxo", "pll4";
+
+			tsens: thermal-sensor {
+				compatible = "qcom,msm8960-tsens";
+
+				nvmem-cells = <&tsens_calib>, <&tsens_backup>;
+				nvmem-cell-names = "calib", "calib_backup";
+				interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "uplow";
+
+				#qcom,sensors = <11>;
+				#thermal-sensor-cells = <1>;
+			};
 		};
 
 		lcc: clock-controller@28000000 {
@@ -825,6 +740,20 @@
 			reg = <0x28000000 0x1000>;
 			#clock-cells = <1>;
 			#reset-cells = <1>;
+			clocks = <&pxo_board>,
+				 <&gcc PLL4_VOTE>,
+				 <0>,
+				 <0>, <0>,
+				 <0>, <0>,
+				 <0>;
+			clock-names = "pxo",
+				      "pll4_vote",
+				      "mi2s_codec_clk",
+				      "codec_i2s_mic_codec_clk",
+				      "spare_i2s_mic_codec_clk",
+				      "codec_i2s_spkr_codec_clk",
+				      "spare_i2s_spkr_codec_clk",
+				      "pcm_codec_clk";
 		};
 
 		mmcc: clock-controller@4000000 {
@@ -833,80 +762,49 @@
 			#clock-cells = <1>;
 			#power-domain-cells = <1>;
 			#reset-cells = <1>;
+			clocks = <&pxo_board>,
+				 <&gcc PLL3>,
+				 <&gcc PLL8_VOTE>,
+				 <&dsi0_phy 1>,
+				 <&dsi0_phy 0>,
+				 <&dsi1_phy 1>,
+				 <&dsi1_phy 0>,
+				 <&hdmi_phy>,
+				 <&mdp>;
+			clock-names = "pxo",
+				      "pll3",
+				      "pll8_vote",
+				      "dsi1pll",
+				      "dsi1pllbyte",
+				      "dsi2pll",
+				      "dsi2pllbyte",
+				      "hdmipll",
+				      "lvdspll";
 		};
 
 		l2cc: clock-controller@2011000 {
-			compatible	= "qcom,kpss-gcc", "syscon";
-			reg		= <0x2011000 0x1000>;
+			compatible = "qcom,kpss-gcc-apq8064", "qcom,kpss-gcc", "syscon";
+			reg = <0x2011000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			#clock-cells = <0>;
 		};
 
-		rpm@108000 {
-			compatible	= "qcom,rpm-apq8064";
-			reg		= <0x108000 0x1000>;
-			qcom,ipc	= <&l2cc 0x8 2>;
+		rpm: rpm@108000 {
+			compatible = "qcom,rpm-apq8064";
+			reg = <0x108000 0x1000>;
+			qcom,ipc = <&l2cc 0x8 2>;
 
-			interrupts	= <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
-					  <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
-					  <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
-			interrupt-names	= "ack", "err", "wakeup";
+			interrupts = <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "ack", "err", "wakeup";
 
 			rpmcc: clock-controller {
-				compatible	= "qcom,rpmcc-apq8064", "qcom,rpmcc";
+				compatible = "qcom,rpmcc-apq8064", "qcom,rpmcc";
 				#clock-cells = <1>;
-			};
-
-			regulators {
-				compatible = "qcom,rpm-pm8921-regulators";
-
-				pm8921_s1: s1 {};
-				pm8921_s2: s2 {};
-				pm8921_s3: s3 {};
-				pm8921_s4: s4 {};
-				pm8921_s7: s7 {};
-				pm8921_s8: s8 {};
-
-				pm8921_l1: l1 {};
-				pm8921_l2: l2 {};
-				pm8921_l3: l3 {};
-				pm8921_l4: l4 {};
-				pm8921_l5: l5 {};
-				pm8921_l6: l6 {};
-				pm8921_l7: l7 {};
-				pm8921_l8: l8 {};
-				pm8921_l9: l9 {};
-				pm8921_l10: l10 {};
-				pm8921_l11: l11 {};
-				pm8921_l12: l12 {};
-				pm8921_l14: l14 {};
-				pm8921_l15: l15 {};
-				pm8921_l16: l16 {};
-				pm8921_l17: l17 {};
-				pm8921_l18: l18 {};
-				pm8921_l21: l21 {};
-				pm8921_l22: l22 {};
-				pm8921_l23: l23 {};
-				pm8921_l24: l24 {};
-				pm8921_l25: l25 {};
-				pm8921_l26: l26 {};
-				pm8921_l27: l27 {};
-				pm8921_l28: l28 {};
-				pm8921_l29: l29 {};
-
-				pm8921_lvs1: lvs1 {};
-				pm8921_lvs2: lvs2 {};
-				pm8921_lvs3: lvs3 {};
-				pm8921_lvs4: lvs4 {};
-				pm8921_lvs5: lvs5 {};
-				pm8921_lvs6: lvs6 {};
-				pm8921_lvs7: lvs7 {};
-
-				pm8921_usb_switch: usb-switch {};
-
-				pm8921_hdmi_switch: hdmi-switch {
-					bias-pull-down;
-				};
-
-				pm8921_ncp: ncp {};
+				clocks = <&pxo_board>, <&cxo_board>;
+				clock-names = "pxo", "cxo";
 			};
 		};
 
@@ -1004,133 +902,122 @@
 		};
 
 		sata_phy0: phy@1b400000 {
-			compatible	= "qcom,apq8064-sata-phy";
-			status		= "disabled";
-			reg		= <0x1b400000 0x200>;
-			reg-names	= "phy_mem";
-			clocks		= <&gcc SATA_PHY_CFG_CLK>;
-			clock-names	= "cfg";
-			#phy-cells	= <0>;
+			compatible = "qcom,apq8064-sata-phy";
+			status = "disabled";
+			reg = <0x1b400000 0x200>;
+			clocks = <&gcc SATA_PHY_CFG_CLK>;
+			clock-names = "cfg";
+			#phy-cells = <0>;
 		};
 
 		sata0: sata@29000000 {
-			compatible		= "qcom,apq8064-ahci", "generic-ahci";
-			status			= "disabled";
-			reg			= <0x29000000 0x180>;
-			interrupts		= <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
-
-			clocks			= <&gcc SFAB_SATA_S_H_CLK>,
-						<&gcc SATA_H_CLK>,
-						<&gcc SATA_A_CLK>,
-						<&gcc SATA_RXOOB_CLK>,
-						<&gcc SATA_PMALIVE_CLK>;
-			clock-names		= "slave_iface",
-						"iface",
-						"bus",
-						"rxoob",
-						"core_pmalive";
-
-			assigned-clocks		= <&gcc SATA_RXOOB_CLK>,
-						<&gcc SATA_PMALIVE_CLK>;
-			assigned-clock-rates	= <100000000>, <100000000>;
-
-			phys			= <&sata_phy0>;
-			phy-names		= "sata-phy";
-			ports-implemented	= <0x1>;
-		};
-
-		/* Temporary fixed regulator */
-		sdcc1bam:dma@12402000{
-			compatible = "qcom,bam-v1.3.0";
-			reg = <0x12402000 0x8000>;
-			interrupts = <0 98 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc SDC1_H_CLK>;
-			clock-names = "bam_clk";
-			#dma-cells = <1>;
-			qcom,ee = <0>;
-		};
-
-		sdcc3bam:dma@12182000{
+			compatible = "qcom,apq8064-ahci", "generic-ahci";
+			status	 = "disabled";
+			reg	 = <0x29000000 0x180>;
+			interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc SFAB_SATA_S_H_CLK>,
+				 <&gcc SATA_H_CLK>,
+				 <&gcc SATA_A_CLK>,
+				 <&gcc SATA_RXOOB_CLK>,
+				 <&gcc SATA_PMALIVE_CLK>;
+			clock-names = "slave_iface",
+				      "iface",
+				      "core",
+				      "rxoob",
+				      "pmalive";
+
+			assigned-clocks = <&gcc SATA_RXOOB_CLK>,
+					  <&gcc SATA_PMALIVE_CLK>;
+			assigned-clock-rates = <100000000>, <100000000>;
+
+			phys = <&sata_phy0>;
+			phy-names = "sata-phy";
+			ports-implemented = <0x1>;
+		};
+
+		sdcc3: mmc@12180000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00051180>;
+			status = "disabled";
+			reg = <0x12180000 0x2000>;
+			interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <192000000>;
+			no-1-8-v;
+			dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
+			dma-names = "tx", "rx";
+		};
+
+		sdcc3bam: dma-controller@12182000 {
 			compatible = "qcom,bam-v1.3.0";
 			reg = <0x12182000 0x8000>;
-			interrupts = <0 96 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc SDC3_H_CLK>;
 			clock-names = "bam_clk";
 			#dma-cells = <1>;
 			qcom,ee = <0>;
 		};
 
-		sdcc4bam:dma@121c2000{
+		sdcc4: mmc@121c0000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00051180>;
+			status = "disabled";
+			reg = <0x121c0000 0x2000>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC4_CLK>, <&gcc SDC4_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <48000000>;
+			dmas = <&sdcc4bam 2>, <&sdcc4bam 1>;
+			dma-names = "tx", "rx";
+			pinctrl-names = "default";
+			pinctrl-0 = <&sdc4_default_state>;
+		};
+
+		sdcc4bam: dma-controller@121c2000 {
 			compatible = "qcom,bam-v1.3.0";
 			reg = <0x121c2000 0x8000>;
-			interrupts = <0 95 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc SDC4_H_CLK>;
 			clock-names = "bam_clk";
 			#dma-cells = <1>;
 			qcom,ee = <0>;
 		};
 
-		amba {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-			sdcc1: mmc@12400000 {
-				status		= "disabled";
-				compatible	= "arm,pl18x", "arm,primecell";
-				pinctrl-names	= "default";
-				pinctrl-0	= <&sdcc1_pins>;
-				arm,primecell-periphid = <0x00051180>;
-				reg		= <0x12400000 0x2000>;
-				interrupts	= <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <8>;
-				max-frequency	= <96000000>;
-				non-removable;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
-				dma-names = "tx", "rx";
-			};
-
-			sdcc3: mmc@12180000 {
-				compatible	= "arm,pl18x", "arm,primecell";
-				arm,primecell-periphid = <0x00051180>;
-				status		= "disabled";
-				reg		= <0x12180000 0x2000>;
-				interrupts	= <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <4>;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				max-frequency	= <192000000>;
-				no-1-8-v;
-				dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
-				dma-names = "tx", "rx";
-			};
-
-			sdcc4: mmc@121c0000 {
-				compatible	= "arm,pl18x", "arm,primecell";
-				arm,primecell-periphid = <0x00051180>;
-				status		= "disabled";
-				reg		= <0x121c0000 0x2000>;
-				interrupts	= <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC4_CLK>, <&gcc SDC4_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <4>;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				max-frequency	= <48000000>;
-				dmas = <&sdcc4bam 2>, <&sdcc4bam 1>;
-				dma-names = "tx", "rx";
-				pinctrl-names = "default";
-				pinctrl-0 = <&sdc4_gpios>;
-			};
+		sdcc1: mmc@12400000 {
+			status = "disabled";
+			compatible = "arm,pl18x", "arm,primecell";
+			pinctrl-names = "default";
+			pinctrl-0 = <&sdcc1_default_state>;
+			arm,primecell-periphid = <0x00051180>;
+			reg = <0x12400000 0x2000>;
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <8>;
+			max-frequency = <96000000>;
+			non-removable;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
+			dma-names = "tx", "rx";
+		};
+
+		sdcc1bam: dma-controller@12402000 {
+			compatible = "qcom,bam-v1.3.0";
+			reg = <0x12402000 0x8000>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC1_H_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
 		};
 
 		tcsr: syscon@1a400000 {
@@ -1138,7 +1025,7 @@
 			reg = <0x1a400000 0x100>;
 		};
 
-		gpu: adreno-3xx@4300000 {
+		gpu: gpu@4300000 {
 			compatible = "qcom,adreno-320.2", "qcom,adreno";
 			reg = <0x04300000 0x20000>;
 			reg-names = "kgsl_3d0_reg_memory";
@@ -1225,7 +1112,7 @@
 			gpu_opp_table: opp-table {
 				compatible = "operating-points-v2";
 
-				opp-320000000 {
+				opp-450000000 {
 					opp-hz = /bits/ 64 <450000000>;
 				};
 
@@ -1236,13 +1123,13 @@
 		};
 
 		mmss_sfpb: syscon@5700000 {
-			compatible = "syscon";
+			compatible = "qcom,apq8064-mmss-sfpb", "syscon";
 			reg = <0x5700000 0x70>;
 		};
 
 		dsi0: dsi@4700000 {
-			compatible = "qcom,mdss-dsi-ctrl";
-			label = "MDSS DSI CTRL->0";
+			compatible = "qcom,apq8064-dsi-ctrl",
+				     "qcom,mdss-dsi-ctrl";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
@@ -1270,7 +1157,8 @@
 						<&dsi0_phy 1>;
 			syscon-sfpb = <&mmss_sfpb>;
 			phys = <&dsi0_phy>;
-			phy-names = "dsi";
+			status = "disabled";
+
 			ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1290,7 +1178,7 @@
 		};
 
 
-		dsi0_phy: dsi-phy@4700200 {
+		dsi0_phy: phy@4700200 {
 			compatible = "qcom,dsi-phy-28nm-8960";
 			#clock-cells = <1>;
 			#phy-cells = <0>;
@@ -1299,11 +1187,86 @@
 				<0x04700300 0x200>,
 				<0x04700500 0x5c>;
 			reg-names = "dsi_pll", "dsi_phy", "dsi_phy_regulator";
-			clock-names = "iface_clk", "ref";
+			clock-names = "iface", "ref";
 			clocks = <&mmcc DSI_M_AHB_CLK>,
 				 <&pxo_board>;
+			status = "disabled";
 		};
 
+		dsi1: dsi@5800000 {
+			compatible = "qcom,mdss-dsi-ctrl";
+			interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
+			reg = <0x05800000 0x200>;
+			reg-names = "dsi_ctrl";
+
+			clocks = <&mmcc DSI2_M_AHB_CLK>,
+				 <&mmcc DSI2_S_AHB_CLK>,
+				 <&mmcc AMP_AHB_CLK>,
+				 <&mmcc DSI2_CLK>,
+				 <&mmcc DSI2_BYTE_CLK>,
+				 <&mmcc DSI2_PIXEL_CLK>,
+				 <&mmcc DSI2_ESC_CLK>;
+			clock-names = "iface",
+				      "bus",
+				      "core_mmss",
+				      "src",
+				      "byte",
+				      "pixel",
+				      "core";
+
+			assigned-clocks = <&mmcc DSI2_BYTE_SRC>,
+					  <&mmcc DSI2_ESC_SRC>,
+					  <&mmcc DSI2_SRC>,
+					  <&mmcc DSI2_PIXEL_SRC>;
+			assigned-clock-parents = <&dsi1_phy 0>,
+						 <&dsi1_phy 0>,
+						 <&dsi1_phy 1>,
+						 <&dsi1_phy 1>;
+
+			syscon-sfpb = <&mmss_sfpb>;
+			phys = <&dsi1_phy>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					dsi1_in: endpoint {
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					dsi1_out: endpoint {
+					};
+				};
+			};
+		};
+
+
+		dsi1_phy: dsi-phy@5800200 {
+			compatible = "qcom,dsi-phy-28nm-8960";
+			reg = <0x05800200 0x100>,
+			      <0x05800300 0x200>,
+			      <0x05800500 0x5c>;
+			reg-names = "dsi_pll",
+				    "dsi_phy",
+				    "dsi_phy_regulator";
+			clock-names = "iface",
+				      "ref";
+			clocks = <&mmcc DSI2_M_AHB_CLK>,
+				 <&pxo_board>;
+			#clock-cells = <1>;
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
 
 		mdp_port0: iommu@7500000 {
 			compatible = "qcom,apq8064-iommu";
@@ -1369,8 +1332,8 @@
 			qcom,ncb = <3>;
 		};
 
-		pcie: pci@1b500000 {
-			compatible = "qcom,pcie-apq8064", "snps,dw-pcie";
+		pcie: pcie@1b500000 {
+			compatible = "qcom,pcie-apq8064";
 			reg = <0x1b500000 0x1000>,
 			      <0x1b502000 0x80>,
 			      <0x1b600000 0x100>,
@@ -1382,16 +1345,16 @@
 			num-lanes = <1>;
 			#address-cells = <3>;
 			#size-cells = <2>;
-			ranges = <0x81000000 0 0          0x0fe00000 0 0x00100000>, /* I/O */
-				 <0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* mem */
+			ranges = <0x81000000 0x0 0x00000000 0x0fe00000 0x0 0x00100000>, /* I/O */
+				 <0x82000000 0x0 0x08000000 0x08000000 0x0 0x07e00000>; /* mem */
 			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 0x7>;
-			interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
-					<0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
-					<0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
-					<0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+			interrupt-map = <0 0 0 1 &intc GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
 			clocks = <&gcc PCIE_A_CLK>,
 				 <&gcc PCIE_H_CLK>,
 				 <&gcc PCIE_PHY_REF_CLK>;
@@ -1403,6 +1366,16 @@
 				 <&gcc PCIE_PHY_RESET>;
 			reset-names = "axi", "ahb", "por", "pci", "phy";
 			status = "disabled";
+
+			pcie@0 {
+				device_type = "pci";
+				reg = <0x0 0x0 0x0 0x0 0x0>;
+				bus-range = <0x01 0xff>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges;
+			};
 		};
 
 		hdmi: hdmi-tx@4a00000 {
@@ -1420,7 +1393,8 @@
 				      "slave_iface";
 
 			phys = <&hdmi_phy>;
-			phy-names = "hdmi-phy";
+
+			status = "disabled";
 
 			ports {
 				#address-cells = <1>;
@@ -1440,7 +1414,7 @@
 			};
 		};
 
-		hdmi_phy: hdmi-phy@4a00400 {
+		hdmi_phy: phy@4a00400 {
 			compatible = "qcom,hdmi-phy-8960";
 			reg = <0x4a00400 0x60>,
 			      <0x4a00500 0x100>;
@@ -1450,9 +1424,12 @@
 			clocks = <&mmcc HDMI_S_AHB_CLK>;
 			clock-names = "slave_iface";
 			#phy-cells = <0>;
+			#clock-cells = <0>;
+
+			status = "disabled";
 		};
 
-		mdp: mdp@5100000 {
+		mdp: display-controller@5100000 {
 			compatible = "qcom,mdp4";
 			reg = <0x05100000 0xf0000>;
 			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
@@ -1461,13 +1438,19 @@
 				 <&mmcc MDP_AXI_CLK>,
 				 <&mmcc MDP_LUT_CLK>,
 				 <&mmcc HDMI_TV_CLK>,
-				 <&mmcc MDP_TV_CLK>;
+				 <&mmcc MDP_TV_CLK>,
+				 <&mmcc LVDS_CLK>,
+				 <&rpmcc RPM_PXO_CLK>;
 			clock-names = "core_clk",
 				      "iface_clk",
 				      "bus_clk",
 				      "lut_clk",
 				      "hdmi_clk",
-				      "tv_clk";
+				      "tv_clk",
+				      "lcdc_clk",
+				      "pxo";
+
+			#clock-cells = <0>;
 
 			iommus = <&mdp_port0 0
 				  &mdp_port0 2
@@ -1504,7 +1487,7 @@
 			};
 		};
 
-		riva: riva-pil@3204000 {
+		riva: riva-pil@3200800 {
 			compatible = "qcom,riva-pil";
 
 			reg = <0x03200800 0x1000>, <0x03202000 0x2000>, <0x03204000 0x100>;
@@ -1516,10 +1499,6 @@
 
 			memory-region = <&wcnss_mem>;
 
-			vddcx-supply = <&pm8921_s3>;
-			vddmx-supply = <&pm8921_l24>;
-			vddpx-supply = <&pm8921_s4>;
-
 			status = "disabled";
 
 			iris {
@@ -1527,11 +1506,6 @@
 
 				clocks = <&cxo_board>;
 				clock-names = "xo";
-
-				vddxo-supply = <&pm8921_l4>;
-				vddrfa-supply = <&pm8921_s2>;
-				vddpa-supply = <&pm8921_l10>;
-				vdddig-supply = <&pm8921_lvs2>;
 			};
 
 			smd-edge {
@@ -1548,7 +1522,7 @@
 
 					qcom,mmio = <&riva>;
 
-					bt {
+					bluetooth {
 						compatible = "qcom,wcnss-bt";
 					};
 
@@ -1567,7 +1541,7 @@
 		};
 
 		etb@1a01000 {
-			compatible = "coresight-etb10", "arm,primecell";
+			compatible = "arm,coresight-etb10", "arm,primecell";
 			reg = <0x1a01000 0x1000>;
 
 			clocks = <&rpmcc RPM_QDSS_CLK>;
@@ -1598,39 +1572,6 @@
 			};
 		};
 
-		replicator {
-			compatible = "arm,coresight-static-replicator";
-
-			clocks = <&rpmcc RPM_QDSS_CLK>;
-			clock-names = "apb_pclk";
-
-			out-ports {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				port@0 {
-					reg = <0>;
-					replicator_out0: endpoint {
-						remote-endpoint = <&etb_in>;
-					};
-				};
-				port@1 {
-					reg = <1>;
-					replicator_out1: endpoint {
-						remote-endpoint = <&tpiu_in>;
-					};
-				};
-			};
-
-			in-ports {
-				port {
-					replicator_in: endpoint {
-						remote-endpoint = <&funnel_out>;
-					};
-				};
-			};
-		};
-
 		funnel@1a04000 {
 			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
 			reg = <0x1a04000 0x1000>;
@@ -1691,7 +1632,7 @@
 			clocks = <&rpmcc RPM_QDSS_CLK>;
 			clock-names = "apb_pclk";
 
-			cpu = <&CPU0>;
+			cpu = <&cpu0>;
 
 			out-ports {
 				port {
@@ -1709,7 +1650,7 @@
 			clocks = <&rpmcc RPM_QDSS_CLK>;
 			clock-names = "apb_pclk";
 
-			cpu = <&CPU1>;
+			cpu = <&cpu1>;
 
 			out-ports {
 				port {
@@ -1727,7 +1668,7 @@
 			clocks = <&rpmcc RPM_QDSS_CLK>;
 			clock-names = "apb_pclk";
 
-			cpu = <&CPU2>;
+			cpu = <&cpu2>;
 
 			out-ports {
 				port {
@@ -1745,7 +1686,7 @@
 			clocks = <&rpmcc RPM_QDSS_CLK>;
 			clock-names = "apb_pclk";
 
-			cpu = <&CPU3>;
+			cpu = <&cpu3>;
 
 			out-ports {
 				port {
diff --git a/arch/arm/boot/dts/qcom/qcom-apq8074-dragonboard.dts b/arch/arm/boot/dts/qcom/qcom-apq8074-dragonboard.dts
new file mode 100644
index 000000000000..34b0cf35fdac
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-apq8074-dragonboard.dts
@@ -0,0 +1,492 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include "qcom-msm8974.dtsi"
+#include "pm8841.dtsi"
+#include "pm8941.dtsi"
+
+/delete-node/ &mpss_region;
+
+/ {
+	model = "Qualcomm APQ8074 Dragonboard";
+	compatible = "qcom,apq8074-dragonboard", "qcom,apq8074";
+
+	aliases {
+		serial0 = &blsp1_uart2;
+		usid0 = &pm8941_0;
+		usid4 = &pm8841_0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		pinctrl-0 = <&msm_keys_default>;
+		pinctrl-names = "default";
+
+		button-volup {
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
+		};
+
+		button-general {
+			label = "General";
+			linux,code = <KEY_PROG1>;
+			gpios = <&pm8941_gpios 23 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	reserved-memory {
+		mpss_region: mpss@ac00000 {
+			reg = <0x0ac00000 0x2500000>;
+			no-map;
+		};
+	};
+
+	vreg_boost: vreg-boost {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vreg-boost";
+		regulator-min-microvolt = <3150000>;
+		regulator-max-microvolt = <3150000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		gpio = <&pm8941_gpios 21 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&boost_bypass_n_pin>;
+	};
+
+	vreg_vph_pwr: vreg-vph-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "vph-pwr";
+
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+
+		regulator-always-on;
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&blsp2_dma {
+	qcom,controlled-remotely;
+};
+
+&blsp2_i2c5 {
+	status = "okay";
+	clock-frequency = <200000>;
+
+	eeprom: eeprom@52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+		pagesize = <32>;
+		read-only;
+	};
+};
+
+&gpu {
+	status = "okay";
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dsi0 {
+	vdda-supply = <&pm8941_l2>;
+	vdd-supply = <&pm8941_l22>;
+	vddio-supply = <&pm8941_l12>;
+
+	status = "okay";
+
+	panel: panel@0 {
+		compatible = "sharp,ls043t1le01-qhd";
+		reg = <0>;
+
+		avdd-supply = <&pm8941_l22>;
+		backlight = <&pm8941_wled>;
+		reset-gpios = <&pm8941_gpios 19 GPIO_ACTIVE_HIGH>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&mdss_dsi0_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&panel_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+	status = "okay";
+
+	vddio-supply = <&pm8941_l12>;
+};
+
+&gpu {
+	status = "okay";
+};
+
+&mdss {
+	status = "okay";
+};
+
+&pm8941_gpios {
+	msm_keys_default: pm8941-gpio-keys-state {
+		pins = "gpio5", "gpio23";
+		function = "normal";
+		input-enable;
+		drive-push-pull;
+		bias-pull-up;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+		power-source = <PM8941_GPIO_S3>; /* 1.8V */
+	};
+};
+
+&pm8941_lpg {
+	qcom,power-source = <1>;
+	status = "okay";
+
+	led@5 {
+		reg = <5>;
+		color = <LED_COLOR_ID_BLUE>;
+		function = LED_FUNCTION_INDICATOR;
+	};
+
+	led@6 {
+		reg = <6>;
+		color = <LED_COLOR_ID_GREEN>;
+		function = LED_FUNCTION_INDICATOR;
+	};
+
+	led@7 {
+		reg = <7>;
+		color = <LED_COLOR_ID_RED>;
+		function = LED_FUNCTION_INDICATOR;
+	};
+};
+
+&pm8941_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+	status = "okay";
+};
+
+&pm8941_wled {
+	qcom,cs-out;
+	qcom,switching-freq = <3200>;
+	qcom,ovp = <32>;
+	qcom,num-strings = <1>;
+
+	status = "okay";
+};
+
+&remoteproc_adsp {
+	cx-supply = <&pm8841_s2>;
+
+	firmware-name = "qcom/apq8074/adsp.mbn";
+
+	status = "okay";
+};
+
+&remoteproc_mss {
+	cx-supply = <&pm8841_s2>;
+	mss-supply = <&pm8841_s3>;
+	mx-supply = <&pm8841_s1>;
+	pll-supply = <&pm8941_l12>;
+
+	firmware-name = "qcom/apq8074/mba.mbn", "qcom/apq8074/modem.mbn";
+
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pm8841-regulators";
+
+		pm8841_s1: s1 {
+			regulator-min-microvolt = <675000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s2: s2 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s3: s3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s4: s4 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,rpm-pm8941-regulators";
+
+		vdd_l1_l3-supply = <&pm8941_s1>;
+		vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+		vdd_l4_l11-supply = <&pm8941_s1>;
+		vdd_l5_l7-supply = <&pm8941_s2>;
+		vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+		vin_5vs-supply = <&pm8941_5v>;
+
+		pm8941_s1: s1 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_s2: s2 {
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+			regulator-boot-on;
+		};
+
+		pm8941_s3: s3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l3: l3 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l4: l4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		pm8941_l11: l11 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8941_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l13: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l15: l15 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8941_l16: l16 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l17: l17 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l18: l18 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l19: l19 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		pm8941_l20: l20 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+			regulator-boot-on;
+		};
+
+		pm8941_l21: l21 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l22: l22 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8941_l23: l23 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8941_l24: l24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			regulator-boot-on;
+		};
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	vmmc-supply = <&pm8941_l20>;
+	vqmmc-supply = <&pm8941_s3>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&pm8941_l21>;
+	vqmmc-supply = <&pm8941_l13>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_on>;
+	pinctrl-1 = <&sdc2_off>;
+};
+
+&smbb {
+	status = "okay";
+};
+
+&tlmm {
+	sdc1_on: sdc1-on-state {
+		clk-pins {
+			pins = "sdc1_clk";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc1_cmd", "sdc1_data";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	sdc2_on: sdc2-on-state {
+		clk-pins {
+			pins = "sdc2_clk";
+			drive-strength = <10>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc2_cmd", "sdc2_data";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+
+		cd-pins {
+			pins = "gpio62";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+};
+
+&usb {
+	status = "okay";
+
+	phys = <&usb_hs2_phy>;
+	phy-select = <&tcsr 0xb000 1>;
+	extcon = <&smbb>, <&usb_id>;
+	vbus-supply = <&chg_otg>;
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+};
+
+&usb_hs2_phy {
+	status = "okay";
+	v3p3-supply = <&pm8941_l24>;
+	v1p8-supply = <&pm8941_l6>;
+	extcon = <&smbb>;
+	qcom,init-seq = /bits/ 8 <0x1 0x63>;
+};
diff --git a/arch/arm/boot/dts/qcom-apq8084-ifc6540.dts b/arch/arm/boot/dts/qcom/qcom-apq8084-ifc6540.dts
index 44cd72f1b1be..1df24c922be9 100644
--- a/arch/arm/boot/dts/qcom-apq8084-ifc6540.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8084-ifc6540.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 #include "qcom-apq8084.dtsi"
-#include "qcom-pma8084.dtsi"
+#include "pma8084.dtsi"
 
 / {
 	model = "Qualcomm APQ8084/IFC6540";
@@ -19,16 +19,16 @@
 		serial@f995e000 {
 			status = "okay";
 		};
+	};
+};
 
-		sdhci@f9824900 {
-			bus-width = <8>;
-			non-removable;
-			status = "okay";
-		};
+&sdhc_1 {
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
 
-		sdhci@f98a4900 {
-			cd-gpios = <&tlmm 122 GPIO_ACTIVE_LOW>;
-			bus-width = <4>;
-		};
-	};
+&sdhc_2 {
+	cd-gpios = <&tlmm 122 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
 };
diff --git a/arch/arm/boot/dts/qcom-apq8084-mtp.dts b/arch/arm/boot/dts/qcom/qcom-apq8084-mtp.dts
index c6b6680248a6..d4e6aee034af 100644
--- a/arch/arm/boot/dts/qcom-apq8084-mtp.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8084-mtp.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 #include "qcom-apq8084.dtsi"
-#include "qcom-pma8084.dtsi"
+#include "pma8084.dtsi"
 
 / {
 	model = "Qualcomm APQ 8084-MTP";
diff --git a/arch/arm/boot/dts/qcom-apq8084.dtsi b/arch/arm/boot/dts/qcom/qcom-apq8084.dtsi
index 52240fc7a1a6..cee0694ef127 100644
--- a/arch/arm/boot/dts/qcom-apq8084.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-apq8084.dtsi
@@ -17,7 +17,7 @@
 		#size-cells = <1>;
 		ranges;
 
-		smem_mem: smem_region@fa00000 {
+		smem_mem: smem-region@fa00000 {
 			reg = <0xfa00000 0x200000>;
 			no-map;
 		};
@@ -32,10 +32,10 @@
 			compatible = "qcom,krait";
 			reg = <0>;
 			enable-method = "qcom,kpss-acc-v2";
-			next-level-cache = <&L2>;
+			next-level-cache = <&l2>;
 			qcom,acc = <&acc0>;
 			qcom,saw = <&saw0>;
-			cpu-idle-states = <&CPU_SPC>;
+			cpu-idle-states = <&cpu_spc>;
 		};
 
 		cpu@1 {
@@ -43,10 +43,10 @@
 			compatible = "qcom,krait";
 			reg = <1>;
 			enable-method = "qcom,kpss-acc-v2";
-			next-level-cache = <&L2>;
+			next-level-cache = <&l2>;
 			qcom,acc = <&acc1>;
 			qcom,saw = <&saw1>;
-			cpu-idle-states = <&CPU_SPC>;
+			cpu-idle-states = <&cpu_spc>;
 		};
 
 		cpu@2 {
@@ -54,10 +54,10 @@
 			compatible = "qcom,krait";
 			reg = <2>;
 			enable-method = "qcom,kpss-acc-v2";
-			next-level-cache = <&L2>;
+			next-level-cache = <&l2>;
 			qcom,acc = <&acc2>;
 			qcom,saw = <&saw2>;
-			cpu-idle-states = <&CPU_SPC>;
+			cpu-idle-states = <&cpu_spc>;
 		};
 
 		cpu@3 {
@@ -65,20 +65,21 @@
 			compatible = "qcom,krait";
 			reg = <3>;
 			enable-method = "qcom,kpss-acc-v2";
-			next-level-cache = <&L2>;
+			next-level-cache = <&l2>;
 			qcom,acc = <&acc3>;
 			qcom,saw = <&saw3>;
-			cpu-idle-states = <&CPU_SPC>;
+			cpu-idle-states = <&cpu_spc>;
 		};
 
-		L2: l2-cache {
-			compatible = "qcom,arch-cache";
+		l2: l2-cache {
+			compatible = "cache";
 			cache-level = <2>;
+			cache-unified;
 			qcom,saw = <&saw_l2>;
 		};
 
 		idle-states {
-			CPU_SPC: spc {
+			cpu_spc: cpu-spc {
 				compatible = "qcom,idle-state-spc",
 						"arm,idle-state";
 				entry-latency-us = <150>;
@@ -95,7 +96,7 @@
 
 	firmware {
 		scm {
-			compatible = "qcom,scm";
+			compatible = "qcom,scm-apq8084", "qcom,scm";
 			clocks = <&gcc GCC_CE1_CLK> , <&gcc GCC_CE1_AXI_CLK>, <&gcc GCC_CE1_AHB_CLK>;
 			clock-names = "core", "bus", "iface";
 		};
@@ -239,26 +240,334 @@
 			reg = <0xf9011000 0x1000>;
 		};
 
-		qfprom: qfprom@fc4bc000 {
+		sram@fc190000 {
+			compatible = "qcom,apq8084-rpm-stats";
+			reg = <0xfc190000 0x10000>;
+		};
+
+		qfprom: efuse@fc4bc000 {
+			compatible = "qcom,apq8084-qfprom", "qcom,qfprom";
+			reg = <0xfc4bc000 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
-			compatible = "qcom,qfprom";
-			reg = <0xfc4bc000 0x1000>;
-			tsens_calib: calib@d0 {
-				reg = <0xd0 0x18>;
+
+			tsens_base1: base1@d0 {
+				reg = <0xd0 0x1>;
+				bits = <0 8>;
+			};
+
+			tsens_s0_p1: s0-p1@d1 {
+				reg = <0xd1 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s1_p1: s1-p1@d2 {
+				reg = <0xd1 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s2_p1: s2-p1@d2 {
+				reg = <0xd2 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s3_p1: s3-p1@d3 {
+				reg = <0xd3 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s4_p1: s4-p1@d4 {
+				reg = <0xd4 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s5_p1: s5-p1@d4 {
+				reg = <0xd4 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s6_p1: s6-p1@d5 {
+				reg = <0xd5 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s7_p1: s7-p1@d6 {
+				reg = <0xd6 0x1>;
+				bits = <2 6>;
 			};
-			tsens_backup: backup@440 {
-				reg = <0x440 0x10>;
+
+			tsens_s8_p1: s8-p1@d7 {
+				reg = <0xd7 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_mode: mode@d7 {
+				reg = <0xd7 0x1>;
+				bits = <6 2>;
+			};
+
+			tsens_s9_p1: s9-p1@d8 {
+				reg = <0xd8 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s10_p1: s10-p1@d8 {
+				reg = <0xd8 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_base2: base2@d9 {
+				reg = <0xd9 0x2>;
+				bits = <4 8>;
+			};
+
+			tsens_s0_p2: s0-p2@da {
+				reg = <0xda 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s1_p2: s1-p2@db {
+				reg = <0xdb 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s2_p2: s2-p2@dc {
+				reg = <0xdc 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s3_p2: s3-p2@dc {
+				reg = <0xdc 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s4_p2: s4-p2@dd {
+				reg = <0xdd 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s5_p2: s5-p2@de {
+				reg = <0xde 0x2>;
+				bits = <2 6>;
+			};
+
+			tsens_s6_p2: s6-p2@df {
+				reg = <0xdf 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s7_p2: s7-p2@e0 {
+				reg = <0xe0 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s8_p2: s8-p2@e0 {
+				reg = <0xe0 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s9_p2: s9-p2@e1 {
+				reg = <0xe1 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s10_p2: s10-p2@e2 {
+				reg = <0xe2 0x2>;
+				bits = <2 6>;
+			};
+
+			tsens_s5_p2_backup: s5-p2-backup@e3 {
+				reg = <0xe3 0x2>;
+				bits = <0 6>;
+			};
+
+			tsens_mode_backup: mode-backup@e3 {
+				reg = <0xe3 0x1>;
+				bits = <6 2>;
+			};
+
+			tsens_s6_p2_backup: s6-p2-backup@e4 {
+				reg = <0xe4 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s7_p2_backup: s7-p2-backup@e4 {
+				reg = <0xe4 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s8_p2_backup: s8-p2-backup@e5 {
+				reg = <0xe5 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s9_p2_backup: s9-p2-backup@e6 {
+				reg = <0xe6 0x2>;
+				bits = <2 6>;
+			};
+
+			tsens_s10_p2_backup: s10-p2-backup@e7 {
+				reg = <0xe7 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_base1_backup: base1-backup@440 {
+				reg = <0x440 0x1>;
+				bits = <0 8>;
+			};
+
+			tsens_s0_p1_backup: s0-p1-backup@441 {
+				reg = <0x441 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s1_p1_backup: s1-p1-backup@442 {
+				reg = <0x441 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s2_p1_backup: s2-p1-backup@442 {
+				reg = <0x442 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s3_p1_backup: s3-p1-backup@443 {
+				reg = <0x443 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s4_p1_backup: s4-p1-backup@444 {
+				reg = <0x444 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s5_p1_backup: s5-p1-backup@444 {
+				reg = <0x444 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s6_p1_backup: s6-p1-backup@445 {
+				reg = <0x445 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s7_p1_backup: s7-p1-backup@446 {
+				reg = <0x446 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_use_backup: use-backup@447 {
+				reg = <0x447 0x1>;
+				bits = <5 3>;
+			};
+
+			tsens_s8_p1_backup: s8-p1-backup@448 {
+				reg = <0x448 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s9_p1_backup: s9-p1-backup@448 {
+				reg = <0x448 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s10_p1_backup: s10-p1-backup@449 {
+				reg = <0x449 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_base2_backup: base2-backup@44a {
+				reg = <0x44a 0x2>;
+				bits = <2 8>;
+			};
+
+			tsens_s0_p2_backup: s0-p2-backup@44b {
+				reg = <0x44b 0x3>;
+				bits = <2 6>;
+			};
+
+			tsens_s1_p2_backup: s1-p2-backup@44c {
+				reg = <0x44c 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s2_p2_backup: s2-p2-backup@44c {
+				reg = <0x44c 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s3_p2_backup: s3-p2-backup@44d {
+				reg = <0x44d 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s4_p2_backup: s4-p2-backup@44e {
+				reg = <0x44e 0x1>;
+				bits = <2 6>;
 			};
 		};
 
-		tsens: thermal-sensor@fc4a8000 {
-			compatible = "qcom,msm8974-tsens";
+		tsens: thermal-sensor@fc4a9000 {
+			compatible = "qcom,msm8974-tsens", "qcom,tsens-v0_1";
 			reg = <0xfc4a9000 0x1000>, /* TM */
 			      <0xfc4a8000 0x1000>; /* SROT */
-			nvmem-cells = <&tsens_calib>, <&tsens_backup>;
-			nvmem-cell-names = "calib", "calib_backup";
+			nvmem-cells = <&tsens_mode>,
+				      <&tsens_base1>, <&tsens_base2>,
+				      <&tsens_use_backup>,
+				      <&tsens_mode_backup>,
+				      <&tsens_base1_backup>, <&tsens_base2_backup>,
+				      <&tsens_s0_p1>, <&tsens_s0_p2>,
+				      <&tsens_s1_p1>, <&tsens_s1_p2>,
+				      <&tsens_s2_p1>, <&tsens_s2_p2>,
+				      <&tsens_s3_p1>, <&tsens_s3_p2>,
+				      <&tsens_s4_p1>, <&tsens_s4_p2>,
+				      <&tsens_s5_p1>, <&tsens_s5_p2>,
+				      <&tsens_s6_p1>, <&tsens_s6_p2>,
+				      <&tsens_s7_p1>, <&tsens_s7_p2>,
+				      <&tsens_s8_p1>, <&tsens_s8_p2>,
+				      <&tsens_s9_p1>, <&tsens_s9_p2>,
+				      <&tsens_s10_p1>, <&tsens_s10_p2>,
+				      <&tsens_s0_p1_backup>, <&tsens_s0_p2_backup>,
+				      <&tsens_s1_p1_backup>, <&tsens_s1_p2_backup>,
+				      <&tsens_s2_p1_backup>, <&tsens_s2_p2_backup>,
+				      <&tsens_s3_p1_backup>, <&tsens_s3_p2_backup>,
+				      <&tsens_s4_p1_backup>, <&tsens_s4_p2_backup>,
+				      <&tsens_s5_p1_backup>, <&tsens_s5_p2_backup>,
+				      <&tsens_s6_p1_backup>, <&tsens_s6_p2_backup>,
+				      <&tsens_s7_p1_backup>, <&tsens_s7_p2_backup>,
+				      <&tsens_s8_p1_backup>, <&tsens_s8_p2_backup>,
+				      <&tsens_s9_p1_backup>, <&tsens_s9_p2_backup>,
+				      <&tsens_s10_p1_backup>, <&tsens_s10_p2_backup>;
+			nvmem-cell-names = "mode",
+					   "base1", "base2",
+					   "use_backup",
+					   "mode_backup",
+					   "base1_backup", "base2_backup",
+					   "s0_p1", "s0_p2",
+					   "s1_p1", "s1_p2",
+					   "s2_p1", "s2_p2",
+					   "s3_p1", "s3_p2",
+					   "s4_p1", "s4_p2",
+					   "s5_p1", "s5_p2",
+					   "s6_p1", "s6_p2",
+					   "s7_p1", "s7_p2",
+					   "s8_p1", "s8_p2",
+					   "s9_p1", "s9_p2",
+					   "s10_p1", "s10_p2",
+					   "s0_p1_backup", "s0_p2_backup",
+					   "s1_p1_backup", "s1_p2_backup",
+					   "s2_p1_backup", "s2_p2_backup",
+					   "s3_p1_backup", "s3_p2_backup",
+					   "s4_p1_backup", "s4_p2_backup",
+					   "s5_p1_backup", "s5_p2_backup",
+					   "s6_p1_backup", "s6_p2_backup",
+					   "s7_p1_backup", "s7_p2_backup",
+					   "s8_p1_backup", "s8_p2_backup",
+					   "s9_p1_backup", "s9_p2_backup",
+					   "s10_p1_backup", "s10_p2_backup";
 			#qcom,sensors = <11>;
+			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow";
 			#thermal-sensor-cells = <1>;
 		};
 		timer@f9020000 {
@@ -320,51 +629,50 @@
 			};
 		};
 
-		saw0: power-controller@f9089000 {
+		saw0: power-manager@f9089000 {
 			compatible = "qcom,apq8084-saw2-v2.1-cpu", "qcom,saw2";
 			reg = <0xf9089000 0x1000>, <0xf9009000 0x1000>;
 		};
 
-		saw1: power-controller@f9099000 {
+		saw1: power-manager@f9099000 {
 			compatible = "qcom,apq8084-saw2-v2.1-cpu", "qcom,saw2";
 			reg = <0xf9099000 0x1000>, <0xf9009000 0x1000>;
 		};
 
-		saw2: power-controller@f90a9000 {
+		saw2: power-manager@f90a9000 {
 			compatible = "qcom,apq8084-saw2-v2.1-cpu", "qcom,saw2";
 			reg = <0xf90a9000 0x1000>, <0xf9009000 0x1000>;
 		};
 
-		saw3: power-controller@f90b9000 {
+		saw3: power-manager@f90b9000 {
 			compatible = "qcom,apq8084-saw2-v2.1-cpu", "qcom,saw2";
 			reg = <0xf90b9000 0x1000>, <0xf9009000 0x1000>;
 		};
 
-		saw_l2: power-controller@f9012000 {
-			compatible = "qcom,saw2";
+		saw_l2: power-manager@f9012000 {
+			compatible = "qcom,apq8084-saw2-v2.1-l2", "qcom,saw2";
 			reg = <0xf9012000 0x1000>;
-			regulator;
 		};
 
-		acc0: clock-controller@f9088000 {
+		acc0: power-manager@f9088000 {
 			compatible = "qcom,kpss-acc-v2";
 			reg = <0xf9088000 0x1000>,
 			      <0xf9008000 0x1000>;
 		};
 
-		acc1: clock-controller@f9098000 {
+		acc1: power-manager@f9098000 {
 			compatible = "qcom,kpss-acc-v2";
 			reg = <0xf9098000 0x1000>,
 			      <0xf9008000 0x1000>;
 		};
 
-		acc2: clock-controller@f90a8000 {
+		acc2: power-manager@f90a8000 {
 			compatible = "qcom,kpss-acc-v2";
 			reg = <0xf90a8000 0x1000>,
 			      <0xf9008000 0x1000>;
 		};
 
-		acc3: clock-controller@f90b8000 {
+		acc3: power-manager@f90b8000 {
 			compatible = "qcom,kpss-acc-v2";
 			reg = <0xf90b8000 0x1000>,
 			      <0xf9008000 0x1000>;
@@ -381,20 +689,33 @@
 			#reset-cells = <1>;
 			#power-domain-cells = <1>;
 			reg = <0xfc400000 0x4000>;
-		};
-
-		tcsr_mutex_regs: syscon@fd484000 {
-			compatible = "syscon";
-			reg = <0xfd484000 0x2000>;
-		};
-
-		tcsr_mutex: hwlock {
-			compatible = "qcom,tcsr-mutex";
-			syscon = <&tcsr_mutex_regs 0 0x80>;
+			clocks = <&xo_board>,
+				 <&sleep_clk>,
+				 <0>, /* ufs */
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>, /* sata */
+				 <0>,
+				 <0>; /* pcie */
+			clock-names = "xo",
+				      "sleep_clk",
+				      "ufs_rx_symbol_0_clk_src",
+				      "ufs_rx_symbol_1_clk_src",
+				      "ufs_tx_symbol_0_clk_src",
+				      "ufs_tx_symbol_1_clk_src",
+				      "sata_asic0_clk",
+				      "sata_rx_clk",
+				      "pcie_pipe";
+		};
+
+		tcsr_mutex: hwlock@fd484000 {
+			compatible = "qcom,apq8084-tcsr-mutex", "qcom,tcsr-mutex";
+			reg = <0xfd484000 0x1000>;
 			#hwlock-cells = <1>;
 		};
 
-		rpm_msg_ram: memory@fc428000 {
+		rpm_msg_ram: sram@fc428000 {
 			compatible = "qcom,rpm-msg-ram";
 			reg = <0xfc428000 0x4000>;
 		};
@@ -419,29 +740,29 @@
 			status = "disabled";
 		};
 
-		sdhci@f9824900 {
+		sdhc_1: mmc@f9824900 {
 			compatible = "qcom,apq8084-sdhci", "qcom,sdhci-msm-v4";
 			reg = <0xf9824900 0x11c>, <0xf9824000 0x800>;
-			reg-names = "hc_mem", "core_mem";
+			reg-names = "hc", "core";
 			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hc_irq", "pwr_irq";
-			clocks = <&gcc GCC_SDCC1_APPS_CLK>,
-				 <&gcc GCC_SDCC1_AHB_CLK>,
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
 				 <&xo_board>;
-			clock-names = "core", "iface", "xo";
+			clock-names = "iface", "core", "xo";
 			status = "disabled";
 		};
 
-		sdhci@f98a4900 {
+		sdhc_2: mmc@f98a4900 {
 			compatible = "qcom,apq8084-sdhci", "qcom,sdhci-msm-v4";
 			reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>;
-			reg-names = "hc_mem", "core_mem";
+			reg-names = "hc", "core";
 			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hc_irq", "pwr_irq";
-			clocks = <&gcc GCC_SDCC2_APPS_CLK>,
-				 <&gcc GCC_SDCC2_AHB_CLK>,
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>,
 				 <&xo_board>;
-			clock-names = "core", "iface", "xo";
+			clock-names = "iface", "core", "xo";
 			status = "disabled";
 		};
 
@@ -462,19 +783,19 @@
 		};
 	};
 
-	smd {
-		compatible = "qcom,smd";
+	rpm: remoteproc {
+		compatible = "qcom,apq8084-rpm-proc", "qcom,rpm-proc";
 
-		rpm {
+		smd-edge {
 			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
 			qcom,ipc = <&apcs 8 0>;
 			qcom,smd-edge = <15>;
 
-			rpm_requests {
-				compatible = "qcom,rpm-apq8084";
+			rpm-requests {
+				compatible = "qcom,rpm-apq8084", "qcom,smd-rpm";
 				qcom,smd-channels = "rpm_requests";
 
-				pma8084-regulators {
+				regulators-0 {
 					compatible = "qcom,rpm-pma8084-regulators";
 
 					pma8084_s1: s1 {};
diff --git a/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac-bit.dts b/arch/arm/boot/dts/qcom/qcom-ipq4018-ap120c-ac-bit.dts
index 028ac8e24797..1b27edce9d4f 100644
--- a/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac-bit.dts
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4018-ap120c-ac-bit.dts
@@ -1,5 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 
+#include <dt-bindings/leds/common.h>
 #include "qcom-ipq4018-ap120c-ac.dtsi"
 
 / {
@@ -8,19 +9,24 @@
 	leds {
 		compatible = "gpio-leds";
 
-		power {
+		led-power {
 			label = "ap120c-ac:green:power";
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_GREEN>;
 			gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
 			default-state = "on";
 		};
 
-		wlan {
+		led-wlan {
 			label = "ap120c-ac:green:wlan";
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_GREEN>;
 			gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
 		};
 
-		support {
+		led-support {
 			label = "ap120c-ac:green:support";
+			color = <LED_COLOR_ID_GREEN>;
 			gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
 			panic-indicator;
 		};
diff --git a/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts b/arch/arm/boot/dts/qcom/qcom-ipq4018-ap120c-ac.dts
index b7916fc26d68..a707057c887d 100644
--- a/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4018-ap120c-ac.dts
@@ -1,25 +1,32 @@
 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 
+#include <dt-bindings/leds/common.h>
 #include "qcom-ipq4018-ap120c-ac.dtsi"
 
 / {
 	leds {
 		compatible = "gpio-leds";
 
-		status: status {
+		status: led-status {
 			label = "ap120c-ac:blue:status";
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_BLUE>;
 			gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
 			default-state = "keep";
 		};
 
-		wlan2g {
+		led-wlan2g {
 			label = "ap120c-ac:green:wlan2g";
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_GREEN>;
 			gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "phy0tpt";
 		};
 
-		wlan5g {
+		led-wlan5g {
 			label = "ap120c-ac:red:wlan5g";
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_RED>;
 			gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "phy1tpt";
 		};
diff --git a/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq4018-ap120c-ac.dtsi
index 1f3b1ce82108..be76bc39ac27 100644
--- a/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4018-ap120c-ac.dtsi
@@ -6,12 +6,20 @@
 
 / {
 	model = "ALFA Network AP120C-AC";
-	compatible = "alfa-network,ap120c-ac";
+	compatible = "alfa-network,ap120c-ac", "qcom,ipq4018";
+
+	aliases {
+		serial0 = &blsp1_uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
 
 	keys {
 		compatible = "gpio-keys";
 
-		reset {
+		key-reset {
 			label = "reset";
 			gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_RESTART>;
@@ -20,46 +28,42 @@
 };
 
 &tlmm {
-	i2c0_pins: i2c0_pinmux {
-		mux_i2c {
-			function = "blsp_i2c0";
-			pins = "gpio58", "gpio59";
-			drive-strength = <16>;
-			bias-disable;
-		};
+	i2c0_pins: i2c0-state {
+		function = "blsp_i2c0";
+		pins = "gpio58", "gpio59";
+		drive-strength = <16>;
+		bias-disable;
 	};
 
-	mdio_pins: mdio_pinmux {
-		mux_mdio {
+	mdio_pins: mdio-state {
+		mdio-pins {
 			pins = "gpio53";
 			function = "mdio";
 			bias-pull-up;
 		};
 
-		mux_mdc {
+		mdc-pins {
 			pins = "gpio52";
 			function = "mdc";
 			bias-pull-up;
 		};
 	};
 
-	serial0_pins: serial0_pinmux {
-		mux_uart {
-			pins = "gpio60", "gpio61";
-			function = "blsp_uart0";
-			bias-disable;
-		};
+	serial0_pins: serial0-state {
+		pins = "gpio60", "gpio61";
+		function = "blsp_uart0";
+		bias-disable;
 	};
 
-	spi0_pins: spi0_pinmux {
-		mux_spi {
+	spi0_pins: spi0-state {
+		spi0-pins {
 			function = "blsp_spi0";
 			pins = "gpio55", "gpio56", "gpio57";
 			drive-strength = <12>;
 			bias-disable;
 		};
 
-		mux_cs {
+		spi0-cs-pins {
 			function = "gpio";
 			pins = "gpio54", "gpio4";
 			drive-strength = <2>;
@@ -68,7 +72,7 @@
 		};
 	};
 
-	usb-power {
+	usb-power-hog {
 		line-name = "USB-power";
 		gpios = <1 GPIO_ACTIVE_HIGH>;
 		gpio-hog;
@@ -162,6 +166,20 @@
 				label = "ART";
 				reg = <0x00170000 0x00010000>;
 				read-only;
+
+				nvmem-layout {
+					compatible = "fixed-layout";
+					#address-cells = <1>;
+					#size-cells = <1>;
+
+					precal_art_1000: precal@1000 {
+						reg = <0x1000 0x2f20>;
+					};
+
+					precal_art_5000: precal@5000 {
+						reg = <0x5000 0x2f20>;
+					};
+				};
 			};
 
 			partition@180000 {
@@ -178,7 +196,7 @@
 		};
 	};
 
-	nand@1 {
+	flash@1 {
 		compatible = "spi-nand";
 		reg = <1>;
 		spi-max-frequency = <40000000>;
@@ -225,11 +243,15 @@
 
 &wifi0 {
 	status = "okay";
+	nvmem-cell-names = "pre-calibration";
+	nvmem-cells = <&precal_art_1000>;
 };
 
 &wifi1 {
 	status = "okay";
-	qcom,ath10k-calibration-variant = "ALFA-Network-AP120C-AC";
+	nvmem-cell-names = "pre-calibration";
+	nvmem-cells = <&precal_art_5000>;
+	qcom,calibration-variant = "ALFA-Network-AP120C-AC";
 };
 
 &usb3_hs_phy {
@@ -239,10 +261,11 @@
 &usb3 {
 	status = "okay";
 
-	dwc3@8a00000 {
-		phys = <&usb3_hs_phy>;
-		phy-names = "usb2-phy";
 	};
+
+&usb3_dwc {
+	phys = <&usb3_hs_phy>;
+	phy-names = "usb2-phy";
 };
 
 &usb2_hs_phy {
diff --git a/arch/arm/boot/dts/qcom-ipq4018-jalapeno.dts b/arch/arm/boot/dts/qcom/qcom-ipq4018-jalapeno.dts
index 394412619894..15baaf0d1529 100644
--- a/arch/arm/boot/dts/qcom-ipq4018-jalapeno.dts
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4018-jalapeno.dts
@@ -7,44 +7,39 @@
 
 / {
 	model = "8devices Jalapeno";
-	compatible = "8dev,jalapeno";
+	compatible = "8dev,jalapeno", "qcom,ipq4018";
 };
 
 &tlmm {
-	mdio_pins: mdio_pinmux {
-		pinmux_1 {
+	mdio_pins: mdio-state {
+		mdio-pins {
 			pins = "gpio53";
 			function = "mdio";
+			bias-pull-up;
 		};
 
-		pinmux_2 {
+		mdc-pins {
 			pins = "gpio52";
 			function = "mdc";
-		};
-
-		pinconf {
-			pins = "gpio52", "gpio53";
 			bias-pull-up;
 		};
 	};
 
-	serial_pins: serial_pinmux {
-		mux {
-			pins = "gpio60", "gpio61";
-			function = "blsp_uart0";
-			bias-disable;
-		};
+	serial_pins: serial-state {
+		pins = "gpio60", "gpio61";
+		function = "blsp_uart0";
+		bias-disable;
 	};
 
-	spi_0_pins: spi_0_pinmux {
-		pin {
+	spi_0_pins: spi-0-state {
+		spi0-pins {
 			function = "blsp_spi0";
 			pins = "gpio55", "gpio56", "gpio57";
 			drive-strength = <2>;
 			bias-disable;
 		};
 
-		pin_cs {
+		spi0-cs-pins {
 			function = "gpio";
 			pins = "gpio54", "gpio59";
 			drive-strength = <2>;
@@ -184,13 +179,13 @@
 &wifi0 {
 	status = "okay";
 
-	qcom,ath10k-calibration-variant = "8devices-Jalapeno";
+	qcom,calibration-variant = "8devices-Jalapeno";
 };
 
 &wifi1 {
 	status = "okay";
 
-	qcom,ath10k-calibration-variant = "8devices-Jalapeno";
+	qcom,calibration-variant = "8devices-Jalapeno";
 };
 
 &usb3_ss_phy {
diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1-c1.dts b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk01.1-c1.dts
index ddaa273f72ca..ddaa273f72ca 100644
--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1-c1.dts
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk01.1-c1.dts
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk01.1.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk01.1.dtsi
new file mode 100644
index 000000000000..efbe89dd4793
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk01.1.dtsi
@@ -0,0 +1,101 @@
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include "qcom-ipq4019.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK01.1";
+
+	aliases {
+		serial0 = &blsp1_uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&prng {
+	status = "okay";
+};
+
+&tlmm {
+	serial_pins: serial-state {
+		pins = "gpio60", "gpio61";
+		function = "blsp_uart0";
+		bias-disable;
+	};
+
+	spi_0_pins: spi-0-state {
+		spi0-pins {
+			pins = "gpio55", "gpio56", "gpio57";
+			function = "blsp_spi0";
+			drive-strength = <12>;
+			bias-disable;
+		};
+		spi0-cs-pins {
+			pins = "gpio54";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+			output-high;
+		};
+	};
+};
+
+&blsp_dma {
+	status = "okay";
+};
+
+&blsp1_spi1 {
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+	flash@0 {
+		reg = <0>;
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <24000000>;
+	};
+};
+
+&blsp1_uart1 {
+	pinctrl-0 = <&serial_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&cryptobam {
+	status = "okay";
+};
+
+&crypto {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&wifi0 {
+	status = "okay";
+};
+
+&wifi1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c1.dts b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk04.1-c1.dts
index a7b1201dd614..0993f840d1fc 100644
--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c1.dts
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk04.1-c1.dts
@@ -8,12 +8,12 @@
 	compatible = "qcom,ipq4019-dk04.1-c1", "qcom,ipq4019";
 
 	soc {
-		dma@7984000 {
-			status = "okay";
-		};
-
-		qpic-nand@79b0000 {
+		dma-controller@7984000 {
 			status = "okay";
 		};
 	};
 };
+
+&nand {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c3.dts b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk04.1-c3.dts
index 7765247125e4..7765247125e4 100644
--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c3.dts
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk04.1-c3.dts
diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk04.1.dtsi
index 7a337dc08741..91e296d2ea82 100644
--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk04.1.dtsi
@@ -24,26 +24,26 @@
 
 	soc {
 		pinctrl@1000000 {
-			serial_0_pins: serial0-pinmux {
+			serial_0_pins: serial0-state {
 				pins = "gpio16", "gpio17";
 				function = "blsp_uart0";
 				bias-disable;
 			};
 
-			serial_1_pins: serial1-pinmux {
+			serial_1_pins: serial1-state {
 				pins = "gpio8", "gpio9",
 					"gpio10", "gpio11";
 				function = "blsp_uart1";
 				bias-disable;
 			};
 
-			spi_0_pins: spi-0-pinmux {
-				pinmux {
+			spi_0_pins: spi-0-state {
+				spi0-pins {
 					function = "blsp_spi0";
 					pins = "gpio13", "gpio14", "gpio15";
 					bias-disable;
 				};
-				pinmux_cs {
+				spi0-cs-pins {
 					function = "gpio";
 					pins = "gpio12";
 					bias-disable;
@@ -51,13 +51,13 @@
 				};
 			};
 
-			i2c_0_pins: i2c-0-pinmux {
+			i2c_0_pins: i2c-0-state {
 				pins = "gpio20", "gpio21";
 				function = "blsp_i2c0";
 				bias-disable;
 			};
 
-			nand_pins: nand-pins {
+			nand_pins: nand-state {
 				pins = "gpio53", "gpio55", "gpio56",
 					"gpio57", "gpio58", "gpio59",
 					"gpio60", "gpio62", "gpio63",
@@ -79,7 +79,7 @@
 			status = "okay";
 		};
 
-		dma@7884000 {
+		dma-controller@7884000 {
 			status = "okay";
 		};
 
@@ -87,25 +87,25 @@
 			pinctrl-0 = <&spi_0_pins>;
 			pinctrl-names = "default";
 			status = "okay";
-			cs-gpios = <&tlmm 12 0>;
+			cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
 
-			m25p80@0 {
+			flash@0 {
 				#address-cells = <1>;
 				#size-cells = <1>;
 				reg = <0>;
-				compatible = "n25q128a11";
+				compatible = "micron,n25q128a11", "jedec,spi-nor";
 				spi-max-frequency = <24000000>;
 			};
 		};
 
-		pci@40000000 {
+		pcie@40000000 {
 			status = "okay";
-			perst-gpio = <&tlmm 38 0x1>;
-		};
-
-		qpic-nand@79b0000 {
-			pinctrl-0 = <&nand_pins>;
-			pinctrl-names = "default";
+			perst-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
 		};
 	};
 };
+
+&nand {
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+};
diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c1.dts b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk07.1-c1.dts
index 06f9f2cb2fe9..41c5874f6f97 100644
--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c1.dts
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk07.1-c1.dts
@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
 // Copyright (c) 2018, The Linux Foundation. All rights reserved.
 
+#include <dt-bindings/gpio/gpio.h>
 #include "qcom-ipq4019-ap.dk07.1.dtsi"
 
 / {
@@ -10,7 +11,7 @@
 	soc {
 		pci@40000000 {
 			status = "okay";
-			perst-gpio = <&tlmm 38 0x1>;
+			perst-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
 		};
 
 		spi@78b6000 {
@@ -18,20 +19,20 @@
 		};
 
 		pinctrl@1000000 {
-			serial_1_pins: serial1-pinmux {
+			serial_1_pins: serial1-state {
 				pins = "gpio8", "gpio9",
 					"gpio10", "gpio11";
 				function = "blsp_uart1";
 				bias-disable;
 			};
 
-			spi_0_pins: spi-0-pinmux {
-				pinmux {
+			spi_0_pins: spi-0-state {
+				spi0-pins {
 					function = "blsp_spi0";
 					pins = "gpio13", "gpio14", "gpio15";
 					bias-disable;
 				};
-				pinmux_cs {
+				spio-cs-pins {
 					function = "gpio";
 					pins = "gpio12";
 					bias-disable;
@@ -50,13 +51,13 @@
 			pinctrl-0 = <&spi_0_pins>;
 			pinctrl-names = "default";
 			status = "okay";
-			cs-gpios = <&tlmm 12 0>;
+			cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
 
-			m25p80@0 {
+			flash@0 {
 				#address-cells = <1>;
 				#size-cells = <1>;
 				reg = <0>;
-				compatible = "n25q128a11";
+				compatible = "micron,n25q128a11", "jedec,spi-nor";
 				spi-max-frequency = <24000000>;
 			};
 		};
diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c2.dts b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk07.1-c2.dts
index bd3553dd2070..67ee99d69757 100644
--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c2.dts
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk07.1-c2.dts
@@ -9,7 +9,7 @@
 
 	soc {
 		pinctrl@1000000 {
-			serial_1_pins: serial1-pinmux {
+			serial_1_pins: serial1-state {
 				pins = "gpio8", "gpio9";
 				function = "blsp_uart1";
 				bias-disable;
diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk07.1.dtsi
index 94872518b5a2..5a95a2d03c42 100644
--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk07.1.dtsi
@@ -24,26 +24,26 @@
 
 	soc {
 		pinctrl@1000000 {
-			serial_0_pins: serial0-pinmux {
+			serial_0_pins: serial0-state {
 				pins = "gpio16", "gpio17";
 				function = "blsp_uart0";
 				bias-disable;
 			};
 
-			i2c_0_pins: i2c-0-pinmux {
+			i2c_0_pins: i2c-0-state {
 				pins = "gpio20", "gpio21";
 				function = "blsp_i2c0";
 				bias-disable;
 			};
 
-			nand_pins: nand-pins {
+			nand_pins: nand-state {
 				pins = "gpio53", "gpio55", "gpio56",
 				       "gpio57", "gpio58", "gpio59",
 				       "gpio60", "gpio62", "gpio63",
 				       "gpio64", "gpio65", "gpio66",
 				       "gpio67", "gpio68", "gpio69";
 				function = "qpic";
-                        };
+			};
 		};
 
 		serial@78af000 {
@@ -52,7 +52,7 @@
 			status = "okay";
 		};
 
-		dma@7884000 {
+		dma-controller@7884000 {
 			status = "okay";
 		};
 
@@ -62,14 +62,14 @@
 			status = "okay";
 		};
 
-		dma@7984000 {
-			status = "okay";
-		};
-
-		qpic-nand@79b0000 {
-			pinctrl-0 = <&nand_pins>;
-			pinctrl-names = "default";
+		dma-controller@7984000 {
 			status = "okay";
 		};
 	};
 };
+
+&nand {
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq4019.dtsi
index a9d0566a3190..8eeaab1c0be1 100644
--- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-ipq4019.dtsi
@@ -47,13 +47,12 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a7";
 			enable-method = "qcom,kpss-acc-v2";
-			next-level-cache = <&L2>;
+			next-level-cache = <&l2>;
 			qcom,acc = <&acc0>;
 			qcom,saw = <&saw0>;
 			reg = <0x0>;
 			clocks = <&gcc GCC_APPS_CLK_SRC>;
 			clock-frequency = <0>;
-			clock-latency = <256000>;
 			operating-points-v2 = <&cpu0_opp_table>;
 		};
 
@@ -61,13 +60,12 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a7";
 			enable-method = "qcom,kpss-acc-v2";
-			next-level-cache = <&L2>;
+			next-level-cache = <&l2>;
 			qcom,acc = <&acc1>;
 			qcom,saw = <&saw1>;
 			reg = <0x1>;
 			clocks = <&gcc GCC_APPS_CLK_SRC>;
 			clock-frequency = <0>;
-			clock-latency = <256000>;
 			operating-points-v2 = <&cpu0_opp_table>;
 		};
 
@@ -75,13 +73,12 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a7";
 			enable-method = "qcom,kpss-acc-v2";
-			next-level-cache = <&L2>;
+			next-level-cache = <&l2>;
 			qcom,acc = <&acc2>;
 			qcom,saw = <&saw2>;
 			reg = <0x2>;
 			clocks = <&gcc GCC_APPS_CLK_SRC>;
 			clock-frequency = <0>;
-			clock-latency = <256000>;
 			operating-points-v2 = <&cpu0_opp_table>;
 		};
 
@@ -89,24 +86,24 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a7";
 			enable-method = "qcom,kpss-acc-v2";
-			next-level-cache = <&L2>;
+			next-level-cache = <&l2>;
 			qcom,acc = <&acc3>;
 			qcom,saw = <&saw3>;
 			reg = <0x3>;
 			clocks = <&gcc GCC_APPS_CLK_SRC>;
 			clock-frequency = <0>;
-			clock-latency = <256000>;
 			operating-points-v2 = <&cpu0_opp_table>;
 		};
 
-		L2: l2-cache {
+		l2: l2-cache {
 			compatible = "cache";
 			cache-level = <2>;
+			cache-unified;
 			qcom,saw = <&saw_l2>;
 		};
 	};
 
-	cpu0_opp_table: opp_table0 {
+	cpu0_opp_table: opp-table {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -125,7 +122,7 @@
 		opp-716000000 {
 			opp-hz = /bits/ 64 <716000000>;
 			clock-latency-ns = <256000>;
- 		};
+		};
 	};
 
 	memory {
@@ -143,7 +140,6 @@
 		sleep_clk: sleep_clk {
 			compatible = "fixed-clock";
 			clock-frequency = <32000>;
-			clock-output-names = "gcc_sleep_clk_src";
 			#clock-cells = <0>;
 		};
 
@@ -156,16 +152,16 @@
 
 	firmware {
 		scm {
-			compatible = "qcom,scm-ipq4019";
+			compatible = "qcom,scm-ipq4019", "qcom,scm";
 		};
 	};
 
 	timer {
 		compatible = "arm,armv7-timer";
-		interrupts = <1 2 0xf08>,
-			     <1 3 0xf08>,
-			     <1 4 0xf08>,
-			     <1 1 0xf08>;
+		interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
 		clock-frequency = <48000000>;
 		always-on;
 	};
@@ -179,6 +175,7 @@
 		intc: interrupt-controller@b000000 {
 			compatible = "qcom,msm-qgic2";
 			interrupt-controller;
+			#address-cells = <0>;
 			#interrupt-cells = <3>;
 			reg = <0x0b000000 0x1000>,
 			<0x0b002000 0x1000>;
@@ -187,9 +184,10 @@
 		gcc: clock-controller@1800000 {
 			compatible = "qcom,gcc-ipq4019";
 			#clock-cells = <1>;
-			#power-domain-cells = <1>;
 			#reset-cells = <1>;
 			reg = <0x1800000 0x60000>;
+			clocks = <&xo>, <&sleep_clk>;
+			clock-names = "xo", "sleep_clk";
 		};
 
 		prng: rng@22000 {
@@ -221,19 +219,23 @@
 			status = "disabled";
 		};
 
-		sdhci: sdhci@7824900 {
-			compatible = "qcom,sdhci-msm-v4";
+		sdhci: mmc@7824900 {
+			compatible = "qcom,ipq4019-sdhci", "qcom,sdhci-msm-v4";
 			reg = <0x7824900 0x11c>, <0x7824000 0x800>;
+			reg-names = "hc", "core";
 			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hc_irq", "pwr_irq";
 			bus-width = <8>;
-			clocks = <&gcc GCC_SDCC1_APPS_CLK>, <&gcc GCC_SDCC1_AHB_CLK>,
-				 <&gcc GCC_DCD_XO_CLK>;
-			clock-names = "core", "iface", "xo";
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
+				 <&xo>;
+			clock-names = "iface",
+				      "core",
+				      "xo";
 			status = "disabled";
 		};
 
-		blsp_dma: dma@7884000 {
+		blsp_dma: dma-controller@7884000 {
 			compatible = "qcom,bam-v1.7.0";
 			reg = <0x07884000 0x23000>;
 			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
@@ -253,8 +255,8 @@
 			clock-names = "core", "iface";
 			#address-cells = <1>;
 			#size-cells = <0>;
-			dmas = <&blsp_dma 5>, <&blsp_dma 4>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 4>, <&blsp_dma 5>;
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -267,8 +269,8 @@
 			clock-names = "core", "iface";
 			#address-cells = <1>;
 			#size-cells = <0>;
-			dmas = <&blsp_dma 7>, <&blsp_dma 6>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 6>, <&blsp_dma 7>;
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -276,13 +278,13 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0x78b7000 0x600>;
 			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				 <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			#address-cells = <1>;
 			#size-cells = <0>;
-			dmas = <&blsp_dma 9>, <&blsp_dma 8>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 8>, <&blsp_dma 9>;
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -290,17 +292,17 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0x78b8000 0x600>;
 			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				 <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			#address-cells = <1>;
 			#size-cells = <0>;
-			dmas = <&blsp_dma 11>, <&blsp_dma 10>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 10>, <&blsp_dma 11>;
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
-		cryptobam: dma@8e04000 {
+		cryptobam: dma-controller@8e04000 {
 			compatible = "qcom,bam-v1.7.0";
 			reg = <0x08e04000 0x20000>;
 			interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>;
@@ -324,54 +326,49 @@
 			status = "disabled";
 		};
 
-		acc0: clock-controller@b088000 {
+		acc0: power-manager@b088000 {
 			compatible = "qcom,kpss-acc-v2";
 			reg = <0x0b088000 0x1000>, <0xb008000 0x1000>;
 		};
 
-		acc1: clock-controller@b098000 {
+		acc1: power-manager@b098000 {
 			compatible = "qcom,kpss-acc-v2";
 			reg = <0x0b098000 0x1000>, <0xb008000 0x1000>;
 		};
 
-		acc2: clock-controller@b0a8000 {
+		acc2: power-manager@b0a8000 {
 			compatible = "qcom,kpss-acc-v2";
 			reg = <0x0b0a8000 0x1000>, <0xb008000 0x1000>;
 		};
 
-		acc3: clock-controller@b0b8000 {
+		acc3: power-manager@b0b8000 {
 			compatible = "qcom,kpss-acc-v2";
 			reg = <0x0b0b8000 0x1000>, <0xb008000 0x1000>;
 		};
 
-		saw0: regulator@b089000 {
-			compatible = "qcom,saw2";
+		saw0: power-manager@b089000 {
+			compatible = "qcom,ipq4019-saw2-cpu", "qcom,saw2";
 			reg = <0x0b089000 0x1000>, <0x0b009000 0x1000>;
-                        regulator;
 		};
 
-		saw1: regulator@b099000 {
-			compatible = "qcom,saw2";
+		saw1: power-manager@b099000 {
+			compatible = "qcom,ipq4019-saw2-cpu", "qcom,saw2";
 			reg = <0x0b099000 0x1000>, <0x0b009000 0x1000>;
-			regulator;
 		};
 
-		saw2: regulator@b0a9000 {
-			compatible = "qcom,saw2";
+		saw2: power-manager@b0a9000 {
+			compatible = "qcom,ipq4019-saw2-cpu", "qcom,saw2";
 			reg = <0x0b0a9000 0x1000>, <0x0b009000 0x1000>;
-			regulator;
 		};
 
-		saw3: regulator@b0b9000 {
-			compatible = "qcom,saw2";
+		saw3: power-manager@b0b9000 {
+			compatible = "qcom,ipq4019-saw2-cpu", "qcom,saw2";
 			reg = <0x0b0b9000 0x1000>, <0x0b009000 0x1000>;
-			regulator;
 		};
 
-		saw_l2: regulator@b012000 {
-			compatible = "qcom,saw2";
+		saw_l2: power-manager@b012000 {
+			compatible = "qcom,ipq4019-saw2-l2", "qcom,saw2";
 			reg = <0xb012000 0x1000>;
-			regulator;
 		};
 
 		blsp1_uart1: serial@78af000 {
@@ -382,8 +379,8 @@
 			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>,
 				<&gcc GCC_BLSP1_AHB_CLK>;
 			clock-names = "core", "iface";
-			dmas = <&blsp_dma 1>, <&blsp_dma 0>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 0>, <&blsp_dma 1>;
+			dma-names = "tx", "rx";
 		};
 
 		blsp1_uart2: serial@78b0000 {
@@ -394,12 +391,12 @@
 			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
 				<&gcc GCC_BLSP1_AHB_CLK>;
 			clock-names = "core", "iface";
-			dmas = <&blsp_dma 3>, <&blsp_dma 2>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 2>, <&blsp_dma 3>;
+			dma-names = "tx", "rx";
 		};
 
 		watchdog: watchdog@b017000 {
-			compatible = "qcom,kpss-wdt", "qcom,kpss-wdt-ipq4019";
+			compatible = "qcom,kpss-wdt-ipq4019", "qcom,kpss-wdt";
 			reg = <0xb017000 0x40>;
 			clocks = <&sleep_clk>;
 			timeout-sec = <10>;
@@ -411,12 +408,12 @@
 			reg = <0x4ab000 0x4>;
 		};
 
-		pcie0: pci@40000000 {
-			compatible = "qcom,pcie-ipq4019", "snps,dw-pcie";
-			reg =  <0x40000000 0xf1d
-				0x40000f20 0xa8
-				0x80000 0x2000
-				0x40100000 0x1000>;
+		pcie0: pcie@40000000 {
+			compatible = "qcom,pcie-ipq4019";
+			reg = <0x40000000 0xf1d>,
+			      <0x40000f20 0xa8>,
+			      <0x80000 0x2000>,
+			      <0x40100000 0x1000>;
 			reg-names = "dbi", "elbi", "parf", "config";
 			device_type = "pci";
 			linux,pci-domain = <0>;
@@ -425,17 +422,17 @@
 			#address-cells = <3>;
 			#size-cells = <2>;
 
-			ranges = <0x81000000 0 0x40200000 0x40200000 0 0x00100000>,
-				 <0x82000000 0 0x40300000 0x40300000 0 0x00d00000>;
+			ranges = <0x81000000 0x0 0x00000000 0x40200000 0x0 0x00100000>,
+				 <0x82000000 0x0 0x40300000 0x40300000 0x0 0x00d00000>;
 
 			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 0x7>;
-			interrupt-map = <0 0 0 1 &intc 0 142 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
-					<0 0 0 2 &intc 0 143 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
-					<0 0 0 3 &intc 0 144 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
-					<0 0 0 4 &intc 0 145 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+			interrupt-map = <0 0 0 1 &intc GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
 			clocks = <&gcc GCC_PCIE_AHB_CLK>,
 				 <&gcc GCC_PCIE_AXI_M_CLK>,
 				 <&gcc GCC_PCIE_AXI_S_CLK>;
@@ -469,9 +466,19 @@
 				      "phy_ahb";
 
 			status = "disabled";
+
+			pcie@0 {
+				device_type = "pci";
+				reg = <0x0 0x0 0x0 0x0 0x0>;
+				bus-range = <0x01 0xff>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges;
+			};
 		};
 
-		qpic_bam: dma@7984000 {
+		qpic_bam: dma-controller@7984000 {
 			compatible = "qcom,bam-v1.7.0";
 			reg = <0x7984000 0x1a000>;
 			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
@@ -540,9 +547,9 @@
 				     <GIC_SPI 46 IRQ_TYPE_EDGE_RISING>,
 				     <GIC_SPI 47 IRQ_TYPE_EDGE_RISING>,
 				     <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names =  "msi0",  "msi1",  "msi2",  "msi3",
-					   "msi4",  "msi5",  "msi6",  "msi7",
-					   "msi8",  "msi9", "msi10", "msi11",
+			interrupt-names = "msi0",  "msi1",  "msi2",  "msi3",
+					  "msi4",  "msi5",  "msi6",  "msi7",
+					  "msi8",  "msi9", "msi10", "msi11",
 					  "msi12", "msi13", "msi14", "msi15",
 					  "legacy";
 			status = "disabled";
@@ -582,9 +589,9 @@
 				     <GIC_SPI 62 IRQ_TYPE_EDGE_RISING>,
 				     <GIC_SPI 63 IRQ_TYPE_EDGE_RISING>,
 				     <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names =  "msi0",  "msi1",  "msi2",  "msi3",
-					   "msi4",  "msi5",  "msi6",  "msi7",
-					   "msi8",  "msi9", "msi10", "msi11",
+			interrupt-names = "msi0",  "msi1",  "msi2",  "msi3",
+					  "msi4",  "msi5",  "msi6",  "msi7",
+					  "msi8",  "msi9", "msi10", "msi11",
 					  "msi12", "msi13", "msi14", "msi15",
 					  "legacy";
 			status = "disabled";
@@ -597,28 +604,37 @@
 			reg = <0x90000 0x64>;
 			status = "disabled";
 
-			ethphy0: ethernet-phy@0 {
+			ethernet-phy-package@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "qcom,qca8075-package";
 				reg = <0>;
-			};
 
-			ethphy1: ethernet-phy@1 {
-				reg = <1>;
-			};
+				qcom,tx-drive-strength-milliwatt = <300>;
 
-			ethphy2: ethernet-phy@2 {
-				reg = <2>;
-			};
+				ethphy0: ethernet-phy@0 {
+					reg = <0>;
+				};
 
-			ethphy3: ethernet-phy@3 {
-				reg = <3>;
-			};
+				ethphy1: ethernet-phy@1 {
+					reg = <1>;
+				};
+
+				ethphy2: ethernet-phy@2 {
+					reg = <2>;
+				};
+
+				ethphy3: ethernet-phy@3 {
+					reg = <3>;
+				};
 
-			ethphy4: ethernet-phy@4 {
-				reg = <4>;
+				ethphy4: ethernet-phy@4 {
+					reg = <4>;
+				};
 			};
 		};
 
-		usb3_ss_phy: ssphy@9a000 {
+		usb3_ss_phy: usb-phy@9a000 {
 			compatible = "qcom,usb-ss-ipq4019-phy";
 			#phy-cells = <0>;
 			reg = <0x9a000 0x800>;
@@ -628,7 +644,7 @@
 			status = "disabled";
 		};
 
-		usb3_hs_phy: hsphy@a6000 {
+		usb3_hs_phy: usb-phy@a6000 {
 			compatible = "qcom,usb-hs-ipq4019-phy";
 			#phy-cells = <0>;
 			reg = <0xa6000 0x40>;
@@ -638,7 +654,7 @@
 			status = "disabled";
 		};
 
-		usb3: usb3@8af8800 {
+		usb3: usb@8af8800 {
 			compatible = "qcom,ipq4019-dwc3", "qcom,dwc3";
 			reg = <0x8af8800 0x100>;
 			#address-cells = <1>;
@@ -646,11 +662,11 @@
 			clocks = <&gcc GCC_USB3_MASTER_CLK>,
 				 <&gcc GCC_USB3_SLEEP_CLK>,
 				 <&gcc GCC_USB3_MOCK_UTMI_CLK>;
-			clock-names = "master", "sleep", "mock_utmi";
+			clock-names = "core", "sleep", "mock_utmi";
 			ranges;
 			status = "disabled";
 
-			dwc3@8a00000 {
+			usb3_dwc: usb@8a00000 {
 				compatible = "snps,dwc3";
 				reg = <0x8a00000 0xf8000>;
 				interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
@@ -660,7 +676,7 @@
 			};
 		};
 
-		usb2_hs_phy: hsphy@a8000 {
+		usb2_hs_phy: usb-phy@a8000 {
 			compatible = "qcom,usb-hs-ipq4019-phy";
 			#phy-cells = <0>;
 			reg = <0xa8000 0x40>;
@@ -670,7 +686,7 @@
 			status = "disabled";
 		};
 
-		usb2: usb2@60f8800 {
+		usb2: usb@60f8800 {
 			compatible = "qcom,ipq4019-dwc3", "qcom,dwc3";
 			reg = <0x60f8800 0x100>;
 			#address-cells = <1>;
@@ -678,11 +694,11 @@
 			clocks = <&gcc GCC_USB2_MASTER_CLK>,
 				 <&gcc GCC_USB2_SLEEP_CLK>,
 				 <&gcc GCC_USB2_MOCK_UTMI_CLK>;
-			clock-names = "master", "sleep", "mock_utmi";
+			clock-names = "core", "sleep", "mock_utmi";
 			ranges;
 			status = "disabled";
 
-			dwc3@6000000 {
+			usb@6000000 {
 				compatible = "snps,dwc3";
 				reg = <0x6000000 0xf8000>;
 				interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8062-smb208.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8062-smb208.dtsi
new file mode 100644
index 000000000000..9d06255104c7
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8062-smb208.dtsi
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include "qcom-ipq8062.dtsi"
+
+&rpm {
+	smb208_regulators: regulators {
+		compatible = "qcom,rpm-smb208-regulators";
+
+		smb208_s1a: s1a {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s1b: s1b {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2a: s2a {
+			regulator-min-microvolt = < 800000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2b: s2b {
+			regulator-min-microvolt = < 800000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8062.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8062.dtsi
new file mode 100644
index 000000000000..5d3ebd3e2e51
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8062.dtsi
@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include "qcom-ipq8064-v2.0.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ8062";
+	compatible = "qcom,ipq8062", "qcom,ipq8064";
+};
diff --git a/arch/arm/boot/dts/qcom-ipq8064-ap148.dts b/arch/arm/boot/dts/qcom/qcom-ipq8064-ap148.dts
index b63d01d10189..5a8bf1a6f559 100644
--- a/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8064-ap148.dts
@@ -7,18 +7,11 @@
 
 	soc {
 		pinmux@800000 {
-			i2c4_pins: i2c4_pinmux {
-				pins = "gpio12", "gpio13";
-				function = "gsbi4";
-				bias-disable;
-			};
-
-			buttons_pins: buttons_pins {
-				mux {
-					pins = "gpio54", "gpio65";
-					drive-strength = <2>;
-					bias-pull-up;
-				};
+			buttons_pins: buttons-state {
+				pins = "gpio54", "gpio65";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-pull-up;
 			};
 		};
 
diff --git a/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts b/arch/arm/boot/dts/qcom/qcom-ipq8064-rb3011.dts
index 596d129d4a95..f09da9460c86 100644
--- a/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8064-rb3011.dts
@@ -1,10 +1,11 @@
 // SPDX-License-Identifier: GPL-2.0
 #include "qcom-ipq8064.dtsi"
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
 
 / {
 	model = "MikroTik RB3011UiAS-RM";
-	compatible = "mikrotik,rb3011";
+	compatible = "mikrotik,rb3011", "qcom,ipq8064";
 
 	aliases {
 		serial0 = &gsbi7_serial;
@@ -19,6 +20,33 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&buttons_pins>;
+		pinctrl-names = "default";
+
+		button {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&qcom_pinmux 66 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			debounce-interval = <60>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&leds_pins>;
+		pinctrl-names = "default";
+
+		led-0 {
+			label = "rb3011:green:user";
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
 	memory@42000000 {
 		reg = <0x42000000 0x3e000000>;
 		device_type = "memory";
@@ -37,8 +65,6 @@
 
 		switch0: switch@10 {
 			compatible = "qca,qca8337";
-			#address-cells = <1>;
-			#size-cells = <0>;
 
 			dsa,member = <0 0>;
 
@@ -66,26 +92,86 @@
 				port@1 {
 					reg = <1>;
 					label = "sw1";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
 				};
 
 				port@2 {
 					reg = <2>;
 					label = "sw2";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
 				};
 
 				port@3 {
 					reg = <3>;
 					label = "sw3";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
 				};
 
 				port@4 {
 					reg = <4>;
 					label = "sw4";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
 				};
 
 				port@5 {
 					reg = <5>;
 					label = "sw5";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
 				};
 			};
 		};
@@ -104,8 +190,6 @@
 
 		switch1: switch@14 {
 			compatible = "qca,qca8337";
-			#address-cells = <1>;
-			#size-cells = <0>;
 
 			dsa,member = <1 0>;
 
@@ -133,26 +217,86 @@
 				port@1 {
 					reg = <1>;
 					label = "sw6";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
 				};
 
 				port@2 {
 					reg = <2>;
 					label = "sw7";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
 				};
 
 				port@3 {
 					reg = <3>;
 					label = "sw8";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
 				};
 
 				port@4 {
 					reg = <4>;
 					label = "sw9";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
 				};
 
 				port@5 {
 					reg = <5>;
 					label = "sw10";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						led@0 {
+							reg = <0>;
+							color = <LED_COLOR_ID_GREEN>;
+							function = LED_FUNCTION_LAN;
+							default-state = "keep";
+						};
+					};
 				};
 			};
 		};
@@ -165,7 +309,6 @@
 
 			spi4: spi@1a280000 {
 				status = "okay";
-				spi-max-frequency = <50000000>;
 
 				pinctrl-0 = <&spi_pins>;
 				pinctrl-names = "default";
@@ -186,33 +329,6 @@
 				};
 			};
 		};
-
-		gpio_keys {
-			compatible = "gpio-keys";
-			pinctrl-0 = <&buttons_pins>;
-			pinctrl-names = "default";
-
-			button@1 {
-				label = "reset";
-				linux,code = <KEY_RESTART>;
-				gpios = <&qcom_pinmux 66 GPIO_ACTIVE_LOW>;
-				linux,input-type = <1>;
-				debounce-interval = <60>;
-			};
-		};
-
-		leds {
-			compatible = "gpio-leds";
-			pinctrl-0 = <&leds_pins>;
-			pinctrl-names = "default";
-
-			led@7 {
-				label = "rb3011:green:user";
-				gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>;
-				default-state = "off";
-			};
-		};
-
 	};
 };
 
@@ -262,8 +378,7 @@
 &nand {
 	status = "okay";
 
-	nandcs@0 {
-		compatible = "qcom,nandcs";
+	nand@0 {
 		reg = <0>;
 
 		nand-ecc-strength = <4>;
@@ -289,68 +404,49 @@
 };
 
 &qcom_pinmux {
-	buttons_pins: buttons_pins {
-		mux {
-			pins = "gpio66";
-			drive-strength = <16>;
-			bias-disable;
-		};
+	buttons_pins: buttons-state {
+		pins = "gpio66";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
 	};
 
-	leds_pins: leds_pins {
-		mux {
-			pins = "gpio33";
-			drive-strength = <16>;
-			bias-disable;
-		};
+	leds_pins: leds-state {
+		pins = "gpio33";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
 	};
 
-	mdio0_pins: mdio0_pins {
-		mux {
-			pins = "gpio0", "gpio1";
-			function = "gpio";
-			drive-strength = <8>;
-			bias-disable;
-		};
+	mdio1_pins: mdio1-state {
+		pins = "gpio10", "gpio11";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
 	};
 
-	mdio1_pins: mdio1_pins {
-		mux {
-			pins = "gpio10", "gpio11";
-			function = "gpio";
-			drive-strength = <8>;
-			bias-disable;
-		};
+	sw0_reset_pin: sw0-reset-state {
+		pins = "gpio16";
+		drive-strength = <16>;
+		function = "gpio";
+		bias-disable;
+		input-disable;
 	};
 
-	sw0_reset_pin: sw0_reset_pin {
-		mux {
-			pins = "gpio16";
-			drive-strength = <16>;
-			function = "gpio";
-			bias-disable;
-			input-disable;
-		};
+	sw1_reset_pin: sw1-reset-state {
+		pins = "gpio17";
+		drive-strength = <16>;
+		function = "gpio";
+		bias-disable;
+		input-disable;
 	};
 
-	sw1_reset_pin: sw1_reset_pin {
-		mux {
-			pins = "gpio17";
-			drive-strength = <16>;
-			function = "gpio";
-			bias-disable;
-			input-disable;
-		};
-	};
-
-	usb1_pwr_en_pins: usb1_pwr_en_pins {
-		mux {
-			pins = "gpio4";
-			function = "gpio";
-			drive-strength = <16>;
-			bias-disable;
-			output-high;
-		};
+	usb1_pwr_en_pins: usb1-pwr-en-state {
+		pins = "gpio4";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+		output-high;
 	};
 };
 
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8064-smb208.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8064-smb208.dtsi
new file mode 100644
index 000000000000..ac9c44f0c164
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8064-smb208.dtsi
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "qcom-ipq8064.dtsi"
+
+&rpm {
+	smb208_regulators: regulators {
+		compatible = "qcom,rpm-smb208-regulators";
+
+		smb208_s1a: s1a {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s1b: s1b {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2a: s2a {
+			regulator-min-microvolt = < 800000>;
+			regulator-max-microvolt = <1250000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2b: s2b {
+			regulator-min-microvolt = < 800000>;
+			regulator-max-microvolt = <1250000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8064-v1.0.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8064-v1.0.dtsi
new file mode 100644
index 000000000000..49de9752632f
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8064-v1.0.dtsi
@@ -0,0 +1,129 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-ipq8064.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ8064-v1.0";
+
+	aliases {
+		serial0 = &gsbi4_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&buttons_pins>;
+		pinctrl-names = "default";
+
+		button-1 {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			debounce-interval = <60>;
+		};
+		button-2 {
+			label = "wps";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			debounce-interval = <60>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&leds_pins>;
+		pinctrl-names = "default";
+
+		led-0 {
+			label = "led_usb1";
+			gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "usbdev";
+			default-state = "off";
+		};
+
+		led-1 {
+			label = "led_usb3";
+			gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "usbdev";
+			default-state = "off";
+		};
+
+		led-2 {
+			label = "status_led_fail";
+			function = LED_FUNCTION_STATUS;
+			gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-3 {
+			label = "sata_led";
+			gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-4 {
+			label = "status_led_pass";
+			function = LED_FUNCTION_STATUS;
+			gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	soc {
+		gsbi@16300000 {
+			qcom,mode = <GSBI_PROT_I2C_UART>;
+			status = "okay";
+
+			serial@16340000 {
+				status = "okay";
+			};
+		};
+
+		gsbi5: gsbi@1a200000 {
+			qcom,mode = <GSBI_PROT_SPI>;
+			status = "okay";
+
+			spi4: spi@1a280000 {
+				status = "okay";
+
+				pinctrl-0 = <&spi_pins>;
+				pinctrl-names = "default";
+
+				cs-gpios = <&qcom_pinmux 20 0>;
+
+				flash: flash@0 {
+					compatible = "s25fl256s1";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					spi-max-frequency = <50000000>;
+					reg = <0>;
+
+					partition@0 {
+						label = "rootfs";
+						reg = <0x0 0x1000000>;
+					};
+
+					partition@1 {
+						label = "scratch";
+						reg = <0x1000000 0x1000000>;
+					};
+				};
+			};
+		};
+
+		sata-phy@1b400000 {
+			status = "okay";
+		};
+
+		sata@29000000 {
+			ports-implemented = <0x1>;
+			status = "okay";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8064-v2.0-smb208.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8064-v2.0-smb208.dtsi
new file mode 100644
index 000000000000..0442580b22de
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8064-v2.0-smb208.dtsi
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "qcom-ipq8064-v2.0.dtsi"
+
+&rpm {
+	smb208_regulators: regulators {
+		compatible = "qcom,rpm-smb208-regulators";
+
+		smb208_s1a: s1a {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s1b: s1b {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2a: s2a {
+			regulator-min-microvolt = < 800000>;
+			regulator-max-microvolt = <1250000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2b: s2b {
+			regulator-min-microvolt = < 800000>;
+			regulator-max-microvolt = <1250000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8064-v2.0.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8064-v2.0.dtsi
new file mode 100644
index 000000000000..2f117d576daf
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8064-v2.0.dtsi
@@ -0,0 +1,69 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "qcom-ipq8064.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ8064-v2.0";
+
+	aliases {
+		serial0 = &gsbi4_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		rsvd@41200000 {
+			reg = <0x41200000 0x300000>;
+			no-map;
+		};
+	};
+};
+
+&gsbi4 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+
+	serial@16340000 {
+		status = "okay";
+	};
+	/*
+	 * The i2c device on gsbi4 should not be enabled.
+	 * On ipq806x designs gsbi4 i2c is meant for exclusive
+	 * RPM usage. Turning this on in kernel manifests as
+	 * i2c failure for the RPM.
+	 */
+};
+
+&pcie0 {
+	compatible = "qcom,pcie-ipq8064-v2";
+};
+
+&pcie1 {
+	compatible = "qcom,pcie-ipq8064-v2";
+};
+
+&pcie2 {
+	compatible = "qcom,pcie-ipq8064-v2";
+};
+
+&sata {
+	ports-implemented = <0x1>;
+};
+
+&ss_phy_0 {
+	qcom,rx-eq = <2>;
+	qcom,tx-deamp_3_5db = <32>;
+	qcom,mpll = <5>;
+};
+
+&ss_phy_1 {
+	qcom,rx-eq = <2>;
+	qcom,tx-deamp_3_5db = <32>;
+	qcom,mpll = <5>;
+};
diff --git a/arch/arm/boot/dts/qcom-ipq8064.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8064.dtsi
index 996f4458d9fc..adedcc6da1da 100644
--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8064.dtsi
@@ -27,7 +27,7 @@
 			enable-method = "qcom,kpss-acc-v1";
 			device_type = "cpu";
 			reg = <0>;
-			next-level-cache = <&L2>;
+			next-level-cache = <&l2>;
 			qcom,acc = <&acc0>;
 			qcom,saw = <&saw0>;
 		};
@@ -37,14 +37,15 @@
 			enable-method = "qcom,kpss-acc-v1";
 			device_type = "cpu";
 			reg = <1>;
-			next-level-cache = <&L2>;
+			next-level-cache = <&l2>;
 			qcom,acc = <&acc1>;
 			qcom,saw = <&saw1>;
 		};
 
-		L2: l2-cache {
+		l2: l2-cache {
 			compatible = "cache";
 			cache-level = <2>;
+			cache-unified;
 		};
 	};
 
@@ -292,19 +293,22 @@
 		};
 
 		smem: smem@41000000 {
+			compatible = "qcom,smem";
 			reg = <0x41000000 0x200000>;
 			no-map;
+
+			hwlocks = <&sfpb_mutex 3>;
 		};
 	};
 
 	clocks {
-		cxo_board {
+		cxo_board: cxo_board {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <25000000>;
 		};
 
-		pxo_board {
+		pxo_board: pxo_board {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <25000000>;
@@ -323,30 +327,70 @@
 		};
 	};
 
+	stmmac_axi_setup: stmmac-axi-config {
+		snps,wr_osr_lmt = <7>;
+		snps,rd_osr_lmt = <7>;
+		snps,blen = <16 0 0 0 0 0 0>;
+	};
+
+	vsdcc_fixed: vsdcc-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "SDCC Power";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
 	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges;
 		compatible = "simple-bus";
 
-		lpass@28100000 {
-			compatible = "qcom,lpass-cpu";
-			status = "disabled";
-			clocks = <&lcc AHBIX_CLK>,
-					<&lcc MI2S_OSR_CLK>,
-					<&lcc MI2S_BIT_CLK>;
-			clock-names = "ahbix-clk",
-					"mi2s-osr-clk",
-					"mi2s-bit-clk";
-			interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>;
-			interrupt-names = "lpass-irq-lpaif";
-			reg = <0x28100000 0x10000>;
-			reg-names = "lpass-lpaif";
+		rpm: rpm@108000 {
+			compatible = "qcom,rpm-ipq8064";
+			reg = <0x00108000 0x1000>;
+			qcom,ipc = <&l2cc 0x8 2>;
+
+			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ack", "err", "wakeup";
+
+			clocks = <&gcc RPM_MSG_RAM_H_CLK>;
+			clock-names = "ram";
+
+			rpmcc: clock-controller {
+				compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc";
+				#clock-cells = <1>;
+			};
+		};
+
+		ssbi@500000 {
+			compatible = "qcom,ssbi";
+			reg = <0x00500000 0x1000>;
+			qcom,controller-type = "pmic-arbiter";
+		};
+
+		qfprom: efuse@700000 {
+			compatible = "qcom,ipq8064-qfprom", "qcom,qfprom";
+			reg = <0x00700000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			speedbin_efuse: speedbin@c0 {
+				reg = <0xc0 0x4>;
+			};
+			tsens_calib: calib@400 {
+				reg = <0x400 0xb>;
+			};
+			tsens_calib_backup: calib-backup@410 {
+				reg = <0x410 0xb>;
+			};
 		};
 
 		qcom_pinmux: pinmux@800000 {
 			compatible = "qcom,ipq8064-pinctrl";
-			reg = <0x800000 0x4000>;
+			reg = <0x00800000 0x4000>;
 
 			gpio-controller;
 			gpio-ranges = <&qcom_pinmux 0 0 69>;
@@ -355,63 +399,58 @@
 			#interrupt-cells = <2>;
 			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
 
-			pcie0_pins: pcie0_pinmux {
-				mux {
-					pins = "gpio3";
-					function = "pcie1_rst";
-					drive-strength = <12>;
-					bias-disable;
-				};
+			pcie0_pins: pcie0-state {
+				pins = "gpio3";
+				function = "pcie1_rst";
+				drive-strength = <12>;
+				bias-disable;
 			};
 
-			pcie1_pins: pcie1_pinmux {
-				mux {
-					pins = "gpio48";
-					function = "pcie2_rst";
-					drive-strength = <12>;
-					bias-disable;
-				};
+			pcie1_pins: pcie1-state {
+				pins = "gpio48";
+				function = "pcie2_rst";
+				drive-strength = <12>;
+				bias-disable;
 			};
 
-			pcie2_pins: pcie2_pinmux {
-				mux {
-					pins = "gpio63";
-					function = "pcie3_rst";
-					drive-strength = <12>;
-					bias-disable;
-				};
+			pcie2_pins: pcie2-state {
+				pins = "gpio63";
+				function = "pcie3_rst";
+				drive-strength = <12>;
+				bias-disable;
 			};
 
-			spi_pins: spi_pins {
-				mux {
-					pins = "gpio18", "gpio19", "gpio21";
-					function = "gsbi5";
-					drive-strength = <10>;
-					bias-none;
-				};
+			i2c4_pins: i2c4-state {
+				pins = "gpio12", "gpio13";
+				function = "gsbi4";
+				drive-strength = <12>;
+				bias-disable;
 			};
 
-			leds_pins: leds_pins {
-				mux {
-					pins = "gpio7", "gpio8", "gpio9",
-					       "gpio26", "gpio53";
-					function = "gpio";
-					drive-strength = <2>;
-					bias-pull-down;
-					output-low;
-				};
+			spi_pins: spi-state {
+				pins = "gpio18", "gpio19", "gpio21";
+				function = "gsbi5";
+				drive-strength = <10>;
+				bias-disable;
 			};
 
-			buttons_pins: buttons_pins {
-				mux {
-					pins = "gpio54";
-					drive-strength = <2>;
-					bias-pull-up;
-				};
+			leds_pins: leds-state {
+				pins = "gpio7", "gpio8", "gpio9",
+					"gpio26", "gpio53";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-pull-down;
+				output-low;
+			};
+
+			buttons_pins: buttons-state {
+				pins = "gpio54";
+				drive-strength = <2>;
+				bias-pull-up;
 			};
 
-			nand_pins: nand_pins {
-				mux {
+			nand_pins: nand-state {
+				nand-pins {
 					pins = "gpio34", "gpio35", "gpio36",
 					       "gpio37", "gpio38", "gpio39",
 					       "gpio40", "gpio41", "gpio42",
@@ -422,31 +461,81 @@
 					bias-disable;
 				};
 
-				pullups {
+				nand-pullup-pins {
 					pins = "gpio39";
+					function = "nand";
+					drive-strength = <10>;
 					bias-pull-up;
 				};
 
-				hold {
+				nand-hold-pins {
 					pins = "gpio40", "gpio41", "gpio42",
 					       "gpio43", "gpio44", "gpio45",
 					       "gpio46", "gpio47";
+					function = "nand";
+					drive-strength = <10>;
 					bias-bus-hold;
 				};
 			};
+
+			mdio0_pins: mdio0-state {
+				pins = "gpio0", "gpio1";
+				function = "mdio";
+				drive-strength = <8>;
+				bias-disable;
+			};
+
+			rgmii2_pins: rgmii2-state {
+				pins = "gpio27", "gpio28", "gpio29",
+					"gpio30", "gpio31", "gpio32",
+					"gpio51", "gpio52", "gpio59",
+					"gpio60", "gpio61", "gpio62";
+				function = "rgmii2";
+				drive-strength = <8>;
+				bias-disable;
+			};
+		};
+
+		gcc: clock-controller@900000 {
+			compatible = "qcom,gcc-ipq8064", "syscon";
+			clocks = <&pxo_board>, <&cxo_board>, <&lcc PLL4>;
+			clock-names = "pxo", "cxo", "pll4";
+			reg = <0x00900000 0x4000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+
+			tsens: thermal-sensor {
+				compatible = "qcom,ipq8064-tsens";
+
+				nvmem-cells = <&tsens_calib>, <&tsens_calib_backup>;
+				nvmem-cell-names = "calib", "calib_backup";
+				interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "uplow";
+
+				#qcom,sensors = <11>;
+				#thermal-sensor-cells = <1>;
+			};
+		};
+
+		sfpb_mutex: hwlock@1200600 {
+			compatible = "qcom,sfpb-mutex";
+			reg = <0x01200600 0x100>;
+
+			#hwlock-cells = <1>;
 		};
 
 		intc: interrupt-controller@2000000 {
 			compatible = "qcom,msm-qgic2";
 			interrupt-controller;
+			#address-cells = <0>;
 			#interrupt-cells = <3>;
 			reg = <0x02000000 0x1000>,
 			      <0x02002000 0x1000>;
 		};
 
 		timer@200a000 {
-			compatible = "qcom,kpss-timer",
-				     "qcom,kpss-wdt-ipq8064", "qcom,msm-timer";
+			compatible = "qcom,kpss-wdt-ipq8064", "qcom,kpss-timer",
+				     "qcom,msm-timer";
 			interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(2) |
 						 IRQ_TYPE_EDGE_RISING)>,
 				     <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(2) |
@@ -458,53 +547,243 @@
 				     <GIC_PPI 5 (GIC_CPU_MASK_SIMPLE(2) |
 						 IRQ_TYPE_EDGE_RISING)>;
 			reg = <0x0200a000 0x100>;
-			clock-frequency = <25000000>,
-					  <32768>;
+			clock-frequency = <25000000>;
 			clocks = <&sleep_clk>;
 			clock-names = "sleep";
 			cpu-offset = <0x80000>;
 		};
 
+		l2cc: clock-controller@2011000 {
+			compatible = "qcom,kpss-gcc-ipq8064", "qcom,kpss-gcc", "syscon";
+			reg = <0x02011000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			#clock-cells = <0>;
+		};
+
 		acc0: clock-controller@2088000 {
 			compatible = "qcom,kpss-acc-v1";
 			reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			clock-output-names = "acpu0_aux";
+			#clock-cells = <0>;
+		};
+
+		saw0: power-manager@2089000 {
+			compatible = "qcom,ipq8064-saw2-cpu", "qcom,saw2";
+			reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
 		};
 
 		acc1: clock-controller@2098000 {
 			compatible = "qcom,kpss-acc-v1";
 			reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			clock-output-names = "acpu1_aux";
+			#clock-cells = <0>;
 		};
 
-		adm_dma: dma-controller@18300000 {
-			compatible = "qcom,adm";
-			reg = <0x18300000 0x100000>;
-			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
-			#dma-cells = <1>;
+		saw1: power-manager@2099000 {
+			compatible = "qcom,ipq8064-saw2-cpu", "qcom,saw2";
+			reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
+		};
 
-			clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
-			clock-names = "core", "iface";
+		nss_common: syscon@3000000 {
+			compatible = "syscon";
+			reg = <0x03000000 0x0000FFFF>;
+		};
 
-			resets = <&gcc ADM0_RESET>,
-				 <&gcc ADM0_PBUS_RESET>,
-				 <&gcc ADM0_C0_RESET>,
-				 <&gcc ADM0_C1_RESET>,
-				 <&gcc ADM0_C2_RESET>;
-			reset-names = "clk", "pbus", "c0", "c1", "c2";
-			qcom,ee = <0>;
+		usb3_0: usb@100f8800 {
+			compatible = "qcom,ipq8064-dwc3", "qcom,dwc3";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x100f8800 0x8000>;
+			clocks = <&gcc USB30_0_MASTER_CLK>;
+			clock-names = "core";
+
+			ranges;
+
+			resets = <&gcc USB30_0_MASTER_RESET>;
 
 			status = "disabled";
+
+			dwc3_0: usb@10000000 {
+				compatible = "snps,dwc3";
+				reg = <0x10000000 0xcd00>;
+				interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&hs_phy_0>, <&ss_phy_0>;
+				phy-names = "usb2-phy", "usb3-phy";
+				dr_mode = "host";
+				snps,dis_u3_susphy_quirk;
+			};
 		};
 
-		saw0: regulator@2089000 {
-			compatible = "qcom,saw2";
-			reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
-			regulator;
+		hs_phy_0: phy@100f8800 {
+			compatible = "qcom,ipq806x-usb-phy-hs";
+			reg = <0x100f8800 0x30>;
+			clocks = <&gcc USB30_0_UTMI_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "disabled";
 		};
 
-		saw1: regulator@2099000 {
-			compatible = "qcom,saw2";
-			reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
-			regulator;
+		ss_phy_0: phy@100f8830 {
+			compatible = "qcom,ipq806x-usb-phy-ss";
+			reg = <0x100f8830 0x30>;
+			clocks = <&gcc USB30_0_MASTER_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		usb3_1: usb@110f8800 {
+			compatible = "qcom,ipq8064-dwc3", "qcom,dwc3";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x110f8800 0x8000>;
+			clocks = <&gcc USB30_1_MASTER_CLK>;
+			clock-names = "core";
+
+			ranges;
+
+			resets = <&gcc USB30_1_MASTER_RESET>;
+
+			status = "disabled";
+
+			dwc3_1: usb@11000000 {
+				compatible = "snps,dwc3";
+				reg = <0x11000000 0xcd00>;
+				interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&hs_phy_1>, <&ss_phy_1>;
+				phy-names = "usb2-phy", "usb3-phy";
+				dr_mode = "host";
+				snps,dis_u3_susphy_quirk;
+			};
+		};
+
+		hs_phy_1: phy@110f8800 {
+			compatible = "qcom,ipq806x-usb-phy-hs";
+			reg = <0x110f8800 0x30>;
+			clocks = <&gcc USB30_1_UTMI_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		ss_phy_1: phy@110f8830 {
+			compatible = "qcom,ipq806x-usb-phy-ss";
+			reg = <0x110f8830 0x30>;
+			clocks = <&gcc USB30_1_MASTER_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		sdcc3bam: dma-controller@12182000 {
+			compatible = "qcom,bam-v1.3.0";
+			reg = <0x12182000 0x8000>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC3_H_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		sdcc1bam: dma-controller@12402000 {
+			compatible = "qcom,bam-v1.3.0";
+			reg = <0x12402000 0x8000>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC1_H_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		amba: amba {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			sdcc3: mmc@12180000 {
+				compatible = "arm,pl18x", "arm,primecell";
+				arm,primecell-periphid = <0x00051180>;
+				status = "disabled";
+				reg = <0x12180000 0x2000>;
+				interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <8>;
+				cap-sd-highspeed;
+				cap-mmc-highspeed;
+				max-frequency = <192000000>;
+				sd-uhs-sdr104;
+				sd-uhs-ddr50;
+				vqmmc-supply = <&vsdcc_fixed>;
+				dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
+				dma-names = "tx", "rx";
+			};
+
+			sdcc1: mmc@12400000 {
+				status = "disabled";
+				compatible = "arm,pl18x", "arm,primecell";
+				arm,primecell-periphid = <0x00051180>;
+				reg = <0x12400000 0x2000>;
+				interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <8>;
+				max-frequency = <96000000>;
+				non-removable;
+				cap-sd-highspeed;
+				cap-mmc-highspeed;
+				vmmc-supply = <&vsdcc_fixed>;
+				dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
+				dma-names = "tx", "rx";
+			};
+		};
+
+		gsbi1: gsbi@12440000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			reg = <0x12440000 0x100>;
+			cell-index = <1>;
+			clocks = <&gcc GSBI1_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+
+			status = "disabled";
+
+			gsbi1_serial: serial@12450000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x12450000 0x100>,
+				      <0x12400000 0x03>;
+				interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI1_UART_CLK>, <&gcc GSBI1_H_CLK>;
+				clock-names = "core", "iface";
+
+				status = "disabled";
+			};
+
+			gsbi1_i2c: i2c@12460000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x12460000 0x1000>;
+				interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>;
+				clock-names = "core", "iface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
 		};
 
 		gsbi2: gsbi@12480000 {
@@ -530,7 +809,7 @@
 				status = "disabled";
 			};
 
-			i2c@124a0000 {
+			gsbi2_i2c: i2c@124a0000 {
 				compatible = "qcom,i2c-qup-v1.1.1";
 				reg = <0x124a0000 0x1000>;
 				interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>;
@@ -581,6 +860,106 @@
 			};
 		};
 
+		gsbi6: gsbi@16500000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			reg = <0x16500000 0x100>;
+			cell-index = <6>;
+			clocks = <&gcc GSBI6_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+
+			status = "disabled";
+
+			gsbi6_i2c: i2c@16580000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x16580000 0x1000>;
+				interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GSBI6_QUP_CLK>, <&gcc GSBI6_H_CLK>;
+				clock-names = "core", "iface";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			gsbi6_spi: spi@16580000 {
+				compatible = "qcom,spi-qup-v1.1.1";
+				reg = <0x16580000 0x1000>;
+				interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GSBI6_QUP_CLK>, <&gcc GSBI6_H_CLK>;
+				clock-names = "core", "iface";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+		};
+
+		gsbi7: gsbi@16600000 {
+			status = "disabled";
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <7>;
+			reg = <0x16600000 0x100>;
+			clocks = <&gcc GSBI7_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			syscon-tcsr = <&tcsr>;
+
+			gsbi7_serial: serial@16640000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x16640000 0x1000>,
+				      <0x16600000 0x1000>;
+				interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+
+			gsbi7_i2c: i2c@16680000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x16680000 0x1000>;
+				interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GSBI7_QUP_CLK>, <&gcc GSBI7_H_CLK>;
+				clock-names = "core", "iface";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+		};
+
+		adm_dma: dma-controller@18300000 {
+			compatible = "qcom,adm";
+			reg = <0x18300000 0x100000>;
+			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+
+			clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
+			clock-names = "core", "iface";
+
+			resets = <&gcc ADM0_RESET>,
+				 <&gcc ADM0_PBUS_RESET>,
+				 <&gcc ADM0_C0_RESET>,
+				 <&gcc ADM0_C1_RESET>,
+				 <&gcc ADM0_C2_RESET>;
+			reset-names = "clk", "pbus", "c0", "c1", "c2";
+			qcom,ee = <0>;
+
+			status = "disabled";
+		};
+
 		gsbi5: gsbi@1a200000 {
 			compatible = "qcom,gsbi-v1.0.0";
 			cell-index = <5>;
@@ -588,6 +967,7 @@
 			clocks = <&gcc GSBI5_H_CLK>;
 			clock-names = "iface";
 			#address-cells = <1>;
+
 			#size-cells = <1>;
 			ranges;
 			status = "disabled";
@@ -631,27 +1011,9 @@
 			};
 		};
 
-		gsbi7: gsbi@16600000 {
-			status = "disabled";
-			compatible = "qcom,gsbi-v1.0.0";
-			cell-index = <7>;
-			reg = <0x16600000 0x100>;
-			clocks = <&gcc GSBI7_H_CLK>;
-			clock-names = "iface";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-			syscon-tcsr = <&tcsr>;
-
-			gsbi7_serial: serial@16640000 {
-				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
-				reg = <0x16640000 0x1000>,
-				      <0x16600000 0x1000>;
-				interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>;
-				clock-names = "core", "iface";
-				status = "disabled";
-			};
+		tcsr: syscon@1a400000 {
+			compatible = "qcom,tcsr-ipq8064", "syscon";
+			reg = <0x1a400000 0x100>;
 		};
 
 		rng@1a500000 {
@@ -661,17 +1023,6 @@
 			clock-names = "core";
 		};
 
-		sata_phy: sata-phy@1b400000 {
-			compatible = "qcom,ipq806x-sata-phy";
-			reg = <0x1b400000 0x200>;
-
-			clocks = <&gcc SATA_PHY_CFG_CLK>;
-			clock-names = "cfg";
-
-			#phy-cells = <0>;
-			status = "disabled";
-		};
-
 		nand: nand-controller@1ac00000 {
 			compatible = "qcom,ipq806x-nand";
 			reg = <0x1ac00000 0x800>;
@@ -694,107 +1045,18 @@
 			status = "disabled";
 		};
 
-		sata: sata@29000000 {
-			compatible = "qcom,ipq806x-ahci", "generic-ahci";
-			reg = <0x29000000 0x180>;
-
-			interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
-
-			clocks = <&gcc SFAB_SATA_S_H_CLK>,
-				 <&gcc SATA_H_CLK>,
-				 <&gcc SATA_A_CLK>,
-				 <&gcc SATA_RXOOB_CLK>,
-				 <&gcc SATA_PMALIVE_CLK>;
-			clock-names = "slave_face", "iface", "core",
-					"rxoob", "pmalive";
+		sata_phy: sata-phy@1b400000 {
+			compatible = "qcom,ipq806x-sata-phy";
+			reg = <0x1b400000 0x200>;
 
-			assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>;
-			assigned-clock-rates = <100000000>, <100000000>;
+			clocks = <&gcc SATA_PHY_CFG_CLK>;
+			clock-names = "cfg";
 
-			phys = <&sata_phy>;
-			phy-names = "sata-phy";
+			#phy-cells = <0>;
 			status = "disabled";
 		};
 
-		qcom,ssbi@500000 {
-			compatible = "qcom,ssbi";
-			reg = <0x00500000 0x1000>;
-			qcom,controller-type = "pmic-arbiter";
-		};
-
-		qfprom: qfprom@700000 {
-			compatible = "qcom,qfprom";
-			reg = <0x00700000 0x1000>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			tsens_calib: calib@400 {
-				reg = <0x400 0xb>;
-			};
-			tsens_calib_backup: calib_backup@410 {
-				reg = <0x410 0xb>;
-			};
-		};
-
-		gcc: clock-controller@900000 {
-			compatible = "qcom,gcc-ipq8064";
-			reg = <0x00900000 0x4000>;
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-			#power-domain-cells = <1>;
-
-			tsens: thermal-sensor@900000 {
-				compatible = "qcom,ipq8064-tsens";
-
-				nvmem-cells = <&tsens_calib>, <&tsens_calib_backup>;
-				nvmem-cell-names = "calib", "calib_backup";
-				interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "uplow";
-
-				#qcom,sensors = <11>;
-				#thermal-sensor-cells = <1>;
-			};
-		};
-
-		rpm: rpm@108000 {
-			compatible = "qcom,rpm-ipq8064";
-			reg = <0x108000 0x1000>;
-			qcom,ipc = <&l2cc 0x8 2>;
-
-			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
-					<GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
-					<GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "ack", "err", "wakeup";
-
-			clocks = <&gcc RPM_MSG_RAM_H_CLK>;
-			clock-names = "ram";
-
-			rpmcc: clock-controller {
-				compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc";
-				#clock-cells = <1>;
-			};
-		};
-
-		tcsr: syscon@1a400000 {
-			compatible = "qcom,tcsr-ipq8064", "syscon";
-			reg = <0x1a400000 0x100>;
-		};
-
-		l2cc: clock-controller@2011000 {
-			compatible = "qcom,kpss-gcc", "syscon";
-			reg = <0x2011000 0x1000>;
-			clocks = <&gcc PLL8_VOTE>, <&gcc PXO_SRC>;
-			clock-names = "pll8_vote", "pxo";
-			clock-output-names = "acpu_l2_aux";
-		};
-
-		lcc: clock-controller@28000000 {
-			compatible = "qcom,lcc-ipq8064";
-			reg = <0x28000000 0x1000>;
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-		};
-
-		pcie0: pci@1b500000 {
+		pcie0: pcie@1b500000 {
 			compatible = "qcom,pcie-ipq8064";
 			reg = <0x1b500000 0x1000
 			       0x1b502000 0x80
@@ -808,17 +1070,17 @@
 			#address-cells = <3>;
 			#size-cells = <2>;
 
-			ranges = <0x81000000 0 0x0fe00000 0x0fe00000 0 0x00100000   /* downstream I/O */
-				  0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* non-prefetchable memory */
+			ranges = <0x81000000 0x0 0x00000000 0x0fe00000 0x0 0x00010000   /* I/O */
+				  0x82000000 0x0 0x08000000 0x08000000 0x0 0x07e00000>; /* MEM */
 
 			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 0x7>;
-			interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
-					<0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
-					<0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
-					<0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+			interrupt-map = <0 0 0 1 &intc GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
 
 			clocks = <&gcc PCIE_A_CLK>,
 				 <&gcc PCIE_H_CLK>,
@@ -842,10 +1104,20 @@
 			pinctrl-names = "default";
 
 			status = "disabled";
-			perst-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
+			perst-gpios = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
+
+			pcie@0 {
+				device_type = "pci";
+				reg = <0x0 0x0 0x0 0x0 0x0>;
+				bus-range = <0x01 0xff>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges;
+			};
 		};
 
-		pcie1: pci@1b700000 {
+		pcie1: pcie@1b700000 {
 			compatible = "qcom,pcie-ipq8064";
 			reg = <0x1b700000 0x1000
 			       0x1b702000 0x80
@@ -859,17 +1131,17 @@
 			#address-cells = <3>;
 			#size-cells = <2>;
 
-			ranges = <0x81000000 0 0x31e00000 0x31e00000 0 0x00100000   /* downstream I/O */
-				  0x82000000 0 0x2e000000 0x2e000000 0 0x03e00000>; /* non-prefetchable memory */
+			ranges = <0x81000000 0x0 0x00000000 0x31e00000 0x0 0x00010000   /* I/O */
+				  0x82000000 0x0 0x2e000000 0x2e000000 0x0 0x03e00000>; /* MEM */
 
 			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 0x7>;
-			interrupt-map = <0 0 0 1 &intc 0 58 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
-					<0 0 0 2 &intc 0 59 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
-					<0 0 0 3 &intc 0 60 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
-					<0 0 0 4 &intc 0 61 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+			interrupt-map = <0 0 0 1 &intc GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
 
 			clocks = <&gcc PCIE_1_A_CLK>,
 				 <&gcc PCIE_1_H_CLK>,
@@ -893,10 +1165,20 @@
 			pinctrl-names = "default";
 
 			status = "disabled";
-			perst-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
+			perst-gpios = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
+
+			pcie@0 {
+				device_type = "pci";
+				reg = <0x0 0x0 0x0 0x0 0x0>;
+				bus-range = <0x01 0xff>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges;
+			};
 		};
 
-		pcie2: pci@1b900000 {
+		pcie2: pcie@1b900000 {
 			compatible = "qcom,pcie-ipq8064";
 			reg = <0x1b900000 0x1000
 			       0x1b902000 0x80
@@ -910,17 +1192,17 @@
 			#address-cells = <3>;
 			#size-cells = <2>;
 
-			ranges = <0x81000000 0 0x35e00000 0x35e00000 0 0x00100000   /* downstream I/O */
-				  0x82000000 0 0x32000000 0x32000000 0 0x03e00000>; /* non-prefetchable memory */
+			ranges = <0x81000000 0x0 0x00000000 0x35e00000 0x0 0x00010000   /* I/O */
+				  0x82000000 0x0 0x32000000 0x32000000 0x0 0x03e00000>; /* MEM */
 
 			interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 0x7>;
-			interrupt-map = <0 0 0 1 &intc 0 72 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
-					<0 0 0 2 &intc 0 73 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
-					<0 0 0 3 &intc 0 74 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
-					<0 0 0 4 &intc 0 75 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+			interrupt-map = <0 0 0 1 &intc GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
 
 			clocks = <&gcc PCIE_2_A_CLK>,
 				 <&gcc PCIE_2_H_CLK>,
@@ -944,12 +1226,17 @@
 			pinctrl-names = "default";
 
 			status = "disabled";
-			perst-gpio = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>;
-		};
+			perst-gpios = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>;
 
-		nss_common: syscon@03000000 {
-			compatible = "syscon";
-			reg = <0x03000000 0x0000FFFF>;
+			pcie@0 {
+				device_type = "pci";
+				reg = <0x0 0x0 0x0 0x0 0x0>;
+				bus-range = <0x01 0xff>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges;
+			};
 		};
 
 		qsgmii_csr: syscon@1bb00000 {
@@ -957,22 +1244,60 @@
 			reg = <0x1bb00000 0x000001FF>;
 		};
 
-		stmmac_axi_setup: stmmac-axi-config {
-			snps,wr_osr_lmt = <7>;
-			snps,rd_osr_lmt = <7>;
-			snps,blen = <16 0 0 0 0 0 0>;
+		lcc: clock-controller@28000000 {
+			compatible = "qcom,lcc-ipq8064";
+			reg = <0x28000000 0x1000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		lpass@28100000 {
+			compatible = "qcom,lpass-cpu";
+			status = "disabled";
+			clocks = <&lcc AHBIX_CLK>,
+					<&lcc MI2S_OSR_CLK>,
+					<&lcc MI2S_BIT_CLK>;
+			clock-names = "ahbix-clk",
+					"mi2s-osr-clk",
+					"mi2s-bit-clk";
+			interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "lpass-irq-lpaif";
+			reg = <0x28100000 0x10000>;
+			reg-names = "lpass-lpaif";
+		};
+
+		sata: sata@29000000 {
+			compatible = "qcom,ipq806x-ahci", "generic-ahci";
+			reg = <0x29000000 0x180>;
+
+			interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc SFAB_SATA_S_H_CLK>,
+				 <&gcc SATA_H_CLK>,
+				 <&gcc SATA_A_CLK>,
+				 <&gcc SATA_RXOOB_CLK>,
+				 <&gcc SATA_PMALIVE_CLK>;
+			clock-names = "slave_iface", "iface", "core",
+					"rxoob", "pmalive";
+
+			assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>;
+			assigned-clock-rates = <100000000>, <100000000>;
+
+			phys = <&sata_phy>;
+			phy-names = "sata-phy";
+			status = "disabled";
 		};
 
 		gmac0: ethernet@37000000 {
 			device_type = "network";
-			compatible = "qcom,ipq806x-gmac";
+			compatible = "qcom,ipq806x-gmac", "snps,dwmac";
 			reg = <0x37000000 0x200000>;
 			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "macirq";
 
 			snps,axi-config = <&stmmac_axi_setup>;
 			snps,pbl = <32>;
-			snps,aal = <1>;
+			snps,aal;
 
 			qcom,nss-common = <&nss_common>;
 			qcom,qsgmii-csr = <&qsgmii_csr>;
@@ -989,14 +1314,14 @@
 
 		gmac1: ethernet@37200000 {
 			device_type = "network";
-			compatible = "qcom,ipq806x-gmac";
+			compatible = "qcom,ipq806x-gmac", "snps,dwmac";
 			reg = <0x37200000 0x200000>;
 			interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "macirq";
 
 			snps,axi-config = <&stmmac_axi_setup>;
 			snps,pbl = <32>;
-			snps,aal = <1>;
+			snps,aal;
 
 			qcom,nss-common = <&nss_common>;
 			qcom,qsgmii-csr = <&qsgmii_csr>;
@@ -1013,14 +1338,14 @@
 
 		gmac2: ethernet@37400000 {
 			device_type = "network";
-			compatible = "qcom,ipq806x-gmac";
+			compatible = "qcom,ipq806x-gmac", "snps,dwmac";
 			reg = <0x37400000 0x200000>;
 			interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "macirq";
 
 			snps,axi-config = <&stmmac_axi_setup>;
 			snps,pbl = <32>;
-			snps,aal = <1>;
+			snps,aal;
 
 			qcom,nss-common = <&nss_common>;
 			qcom,qsgmii-csr = <&qsgmii_csr>;
@@ -1037,14 +1362,14 @@
 
 		gmac3: ethernet@37600000 {
 			device_type = "network";
-			compatible = "qcom,ipq806x-gmac";
+			compatible = "qcom,ipq806x-gmac", "snps,dwmac";
 			reg = <0x37600000 0x200000>;
 			interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "macirq";
 
 			snps,axi-config = <&stmmac_axi_setup>;
 			snps,pbl = <32>;
-			snps,aal = <1>;
+			snps,aal;
 
 			qcom,nss-common = <&nss_common>;
 			qcom,qsgmii-csr = <&qsgmii_csr>;
@@ -1058,168 +1383,5 @@
 
 			status = "disabled";
 		};
-
-		hs_phy_0: phy@100f8800 {
-			compatible = "qcom,ipq806x-usb-phy-hs";
-			reg = <0x100f8800 0x30>;
-			clocks = <&gcc USB30_0_UTMI_CLK>;
-			clock-names = "ref";
-			#phy-cells = <0>;
-
-			status = "disabled";
-		};
-
-		ss_phy_0: phy@100f8830 {
-			compatible = "qcom,ipq806x-usb-phy-ss";
-			reg = <0x100f8830 0x30>;
-			clocks = <&gcc USB30_0_MASTER_CLK>;
-			clock-names = "ref";
-			#phy-cells = <0>;
-
-			status = "disabled";
-		};
-
-		usb3_0: usb3@100f8800 {
-			compatible = "qcom,ipq8064-dwc3", "qcom,dwc3";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			reg = <0x100f8800 0x8000>;
-			clocks = <&gcc USB30_0_MASTER_CLK>;
-			clock-names = "core";
-
-			ranges;
-
-			resets = <&gcc USB30_0_MASTER_RESET>;
-			reset-names = "master";
-
-			status = "disabled";
-
-			dwc3_0: dwc3@10000000 {
-				compatible = "snps,dwc3";
-				reg = <0x10000000 0xcd00>;
-				interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
-				phys = <&hs_phy_0>, <&ss_phy_0>;
-				phy-names = "usb2-phy", "usb3-phy";
-				dr_mode = "host";
-				snps,dis_u3_susphy_quirk;
-			};
-		};
-
-		hs_phy_1: phy@110f8800 {
-			compatible = "qcom,ipq806x-usb-phy-hs";
-			reg = <0x110f8800 0x30>;
-			clocks = <&gcc USB30_1_UTMI_CLK>;
-			clock-names = "ref";
-			#phy-cells = <0>;
-		};
-
-		ss_phy_1: phy@110f8830 {
-			compatible = "qcom,ipq806x-usb-phy-ss";
-			reg = <0x110f8830 0x30>;
-			clocks = <&gcc USB30_1_MASTER_CLK>;
-			clock-names = "ref";
-			#phy-cells = <0>;
-		};
-
-		usb3_1: usb3@110f8800 {
-			compatible = "qcom,ipq8064-dwc3", "qcom,dwc3";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			reg = <0x110f8800 0x8000>;
-			clocks = <&gcc USB30_1_MASTER_CLK>;
-			clock-names = "core";
-
-			ranges;
-
-			resets = <&gcc USB30_1_MASTER_RESET>;
-			reset-names = "master";
-
-			status = "disabled";
-
-			dwc3_1: dwc3@11000000 {
-				compatible = "snps,dwc3";
-				reg = <0x11000000 0xcd00>;
-				interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
-				phys = <&hs_phy_1>, <&ss_phy_1>;
-				phy-names = "usb2-phy", "usb3-phy";
-				dr_mode = "host";
-				snps,dis_u3_susphy_quirk;
-			};
-		};
-
-		vsdcc_fixed: vsdcc-regulator {
-			compatible = "regulator-fixed";
-			regulator-name = "SDCC Power";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-		sdcc1bam: dma@12402000 {
-			compatible = "qcom,bam-v1.3.0";
-			reg = <0x12402000 0x8000>;
-			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc SDC1_H_CLK>;
-			clock-names = "bam_clk";
-			#dma-cells = <1>;
-			qcom,ee = <0>;
-		};
-
-		sdcc3bam: dma@12182000 {
-			compatible = "qcom,bam-v1.3.0";
-			reg = <0x12182000 0x8000>;
-			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc SDC3_H_CLK>;
-			clock-names = "bam_clk";
-			#dma-cells = <1>;
-			qcom,ee = <0>;
-		};
-
-		amba: amba {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-
-			sdcc1: mmc@12400000 {
-				status          = "disabled";
-				compatible      = "arm,pl18x", "arm,primecell";
-				arm,primecell-periphid = <0x00051180>;
-				reg             = <0x12400000 0x2000>;
-				interrupts      = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "cmd_irq";
-				clocks          = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
-				clock-names     = "mclk", "apb_pclk";
-				bus-width       = <8>;
-				max-frequency   = <96000000>;
-				non-removable;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				mmc-ddr-1_8v;
-				vmmc-supply = <&vsdcc_fixed>;
-				dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
-				dma-names = "tx", "rx";
-			};
-
-			sdcc3: mmc@12180000 {
-				compatible      = "arm,pl18x", "arm,primecell";
-				arm,primecell-periphid = <0x00051180>;
-				status          = "disabled";
-				reg             = <0x12180000 0x2000>;
-				interrupts      = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "cmd_irq";
-				clocks          = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
-				clock-names     = "mclk", "apb_pclk";
-				bus-width       = <8>;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				max-frequency   = <192000000>;
-				sd-uhs-sdr104;
-				sd-uhs-ddr50;
-				vqmmc-supply = <&vsdcc_fixed>;
-				dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
-				dma-names = "tx", "rx";
-			};
-		};
 	};
 };
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8065-smb208.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8065-smb208.dtsi
new file mode 100644
index 000000000000..803e6ff99ef8
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8065-smb208.dtsi
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "qcom-ipq8065.dtsi"
+
+&rpm {
+	smb208_regulators: regulators {
+		compatible = "qcom,rpm-smb208-regulators";
+
+		smb208_s1a: s1a {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s1b: s1b {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2a: s2a {
+			regulator-min-microvolt = <775000>;
+			regulator-max-microvolt = <1275000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2b: s2b {
+			regulator-min-microvolt = <775000>;
+			regulator-max-microvolt = <1275000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-ipq8065.dtsi b/arch/arm/boot/dts/qcom/qcom-ipq8065.dtsi
new file mode 100644
index 000000000000..ea49f6cc416d
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-ipq8065.dtsi
@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "qcom-ipq8064-v2.0.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ8065";
+	compatible = "qcom,ipq8065", "qcom,ipq8064";
+};
diff --git a/arch/arm/boot/dts/qcom-mdm9615-wp8548-mangoh-green.dts b/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548-mangoh-green.dts
index 0827de5426c1..e3b4b93c3d38 100644
--- a/arch/arm/boot/dts/qcom-mdm9615-wp8548-mangoh-green.dts
+++ b/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548-mangoh-green.dts
@@ -1,53 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
 /*
  * Device Tree Source for mangOH Green Board with WP8548 Module
  *
  * Copyright (C) 2016 BayLibre, SAS.
  * Author : Neil Armstrong <narmstrong@baylibre.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License as
- *     published by the Free Software Foundation; either version 2 of the
- *     License, or (at your option) any later version.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 #include "qcom-mdm9615-wp8548.dtsi"
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "MangOH Green with WP8548 Module";
@@ -82,17 +45,16 @@
 	 * - 42: IOT0_GPIO1 and SD Card Detect
 	 */
 
-	gpioext1_pins: gpioext1_pins {
-		pins {
+	gpioext1_pins: gpioext1-state {
+		gpioext1-pins {
 			pins = "gpio2";
 			function = "gpio";
-			input-enable;
 			bias-disable;
 		};
 	};
 
-	sdc_cd_pins: sdc_cd_pins {
-		pins {
+	sdc_cd_pins: sdc-cd-state {
+		sdc-cd-pins {
 			pins = "gpio42";
 			function = "gpio";
 			drive-strength = <2>;
@@ -153,7 +115,7 @@
 			#size-cells = <0>;
 			reg = <4>;
 
-			gpioext0: gpio@3e {
+			gpioext0: pinctrl@3e {
 				/* GPIO Expander 0 Mapping :
 				 * - 0: ARDUINO_RESET_Level shift
 				 * - 1: BattChrgr_PG_N
@@ -179,7 +141,7 @@
 				interrupt-parent = <&gpioext1>;
 				interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
 
-				probe-reset;
+				semtech,probe-reset;
 
 				gpio-controller;
 				interrupt-controller;
@@ -191,7 +153,7 @@
 			#size-cells = <0>;
 			reg = <5>;
 
-			gpioext1: gpio@3f {
+			gpioext1: pinctrl@3f {
 				/* GPIO Expander 1 Mapping :
 				 * - 0: GPIOEXP_INT1
 				 * - 1: Battery detect
@@ -220,7 +182,7 @@
 				interrupt-parent = <&msmgpio>;
 				interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
 
-				probe-reset;
+				semtech,probe-reset;
 
 				gpio-controller;
 				interrupt-controller;
@@ -232,7 +194,7 @@
 			#size-cells = <0>;
 			reg = <6>;
 
-			gpioext2: gpio@70 {
+			gpioext2: pinctrl@70 {
 				/* GPIO Expander 2 Mapping :
 				 * - 0: USB_HUB_INTn
 				 * - 1: HUB_CONNECT
@@ -258,7 +220,7 @@
 				interrupt-parent = <&gpioext1>;
 				interrupts = <14 IRQ_TYPE_EDGE_FALLING>;
 
-				probe-reset;
+				semtech,probe-reset;
 
 				gpio-controller;
 				interrupt-controller;
diff --git a/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi b/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi
new file mode 100644
index 000000000000..0dd52cac0e2e
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-mdm9615-wp8548.dtsi
@@ -0,0 +1,275 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Device Tree Source for Sierra Wireless WP8548 Module
+ *
+ * Copyright (C) 2016 BayLibre, SAS.
+ * Author : Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include "qcom-mdm9615.dtsi"
+#include "pm8018.dtsi"
+
+/ {
+	model = "Sierra Wireless WP8548 Module";
+	compatible = "swir,wp8548", "qcom,mdm9615";
+
+	memory@48000000 {
+		device_type = "memory";
+		reg = <0x48000000 0x7F00000>;
+	};
+};
+
+&msmgpio {
+	pinctrl-0 = <&reset_out_pins>;
+	pinctrl-names = "default";
+
+	gsbi3_pins: gsbi3-state {
+		gsbi3-pins {
+			pins = "gpio8", "gpio9", "gpio10", "gpio11";
+			function = "gsbi3";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	gsbi4_pins: gsbi4-state {
+		gsbi4-pins {
+			pins = "gpio12", "gpio13", "gpio14", "gpio15";
+			function = "gsbi4";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	gsbi5_i2c_pins: gsbi5-i2c-state {
+		sda-pins {
+			pins = "gpio16";
+			function = "gsbi5_i2c";
+			drive-strength = <8>;
+			bias-disable;
+		};
+
+		scl-pins {
+			pins = "gpio17";
+			function = "gsbi5_i2c";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	gsbi5_uart_pins: gsbi5-uart-state {
+		gsbi5-uart-pins {
+			pins = "gpio18", "gpio19";
+			function = "gsbi5_uart";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	reset_out_pins: reset-out-state {
+		reset-out-pins {
+			pins = "gpio66";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+			output-high;
+		};
+	};
+};
+
+&pm8018 {
+	interrupts-extended = <&intc GIC_PPI 226 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&pm8018_gpio {
+	usb_vbus_5v_pins: usb-vbus-5v-state {
+		pins = "gpio4";
+		function = "normal";
+		output-high;
+		bias-disable;
+		qcom,drive-strength = <1>;
+		power-source = <2>;
+	};
+};
+
+&gsbi3 {
+	status = "okay";
+	qcom,mode = <GSBI_PROT_SPI>;
+};
+
+&gsbi3_spi {
+	status = "okay";
+	pinctrl-0 = <&gsbi3_pins>;
+	pinctrl-names = "default";
+	assigned-clocks = <&gcc GSBI3_QUP_CLK>;
+	assigned-clock-rates = <24000000>;
+};
+
+&gsbi4 {
+	status = "okay";
+	qcom,mode = <GSBI_PROT_UART_W_FC>;
+};
+
+&gsbi4_serial {
+	status = "okay";
+	pinctrl-0 = <&gsbi4_pins>;
+	pinctrl-names = "default";
+};
+
+&gsbi5 {
+	status = "okay";
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+};
+
+&gsbi5_i2c {
+	status = "okay";
+	clock-frequency = <200000>;
+	pinctrl-0 = <&gsbi5_i2c_pins>;
+	pinctrl-names = "default";
+};
+
+&gsbi5_serial {
+	status = "okay";
+	pinctrl-0 = <&gsbi5_uart_pins>;
+	pinctrl-names = "default";
+};
+
+&rpm {
+	regulators {
+		compatible = "qcom,rpm-pm8018-regulators";
+
+		vin_lvs1-supply = <&pm8018_s3>;
+
+		vdd_l7-supply = <&pm8018_s4>;
+		vdd_l8-supply = <&pm8018_s3>;
+		vdd_l9_l10_l11_l12-supply = <&pm8018_s5>;
+
+		/* Buck SMPS */
+		pm8018_s1: s1 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8018_s2: s2 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8018_s3: s3 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8018_s4: s4 {
+			regulator-min-microvolt = <2100000>;
+			regulator-max-microvolt = <2200000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8018_s5: s5 {
+			regulator-always-on;
+			regulator-min-microvolt = <1350000>;
+			regulator-max-microvolt = <1350000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		/* PMOS LDO */
+		pm8018_l2: l2 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8018_l3: l3 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8018_l4: l4 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+
+		pm8018_l5: l5 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+
+		pm8018_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+
+		pm8018_l7: l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <1900000>;
+			bias-pull-down;
+		};
+
+		pm8018_l8: l8 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8018_l9: l9 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1150000>;
+			bias-pull-down;
+		};
+
+		pm8018_l10: l10 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			bias-pull-down;
+		};
+
+		pm8018_l11: l11 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			bias-pull-down;
+		};
+
+		pm8018_l12: l12 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			bias-pull-down;
+		};
+
+		pm8018_l13: l13 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8018_l14: l14 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+
+		/* Low Voltage Switch */
+		pm8018_lvs1: lvs1 {
+			bias-pull-down;
+		};
+	};
+};
+
+&sdcc1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi b/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi
new file mode 100644
index 000000000000..7de8d6c55016
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-mdm9615.dtsi
@@ -0,0 +1,340 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Device Tree Source for Qualcomm MDM9615 SoC
+ *
+ * Copyright (C) 2016 BayLibre, SAS.
+ * Author : Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,gcc-mdm9615.h>
+#include <dt-bindings/clock/qcom,lcc-msm8960.h>
+#include <dt-bindings/reset/qcom,gcc-mdm9615.h>
+#include <dt-bindings/mfd/qcom-rpm.h>
+#include <dt-bindings/soc/qcom,gsbi.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	model = "Qualcomm MDM9615";
+	compatible = "qcom,mdm9615";
+	interrupt-parent = <&intc>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a5";
+			reg = <0>;
+			device_type = "cpu";
+			next-level-cache = <&l2>;
+		};
+	};
+
+	cpu-pmu {
+		compatible = "arm,cortex-a5-pmu";
+		interrupts = <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	clocks {
+		cxo_board: cxo_board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <19200000>;
+		};
+	};
+
+	vsdcc_fixed: vsdcc-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "SDCC Power";
+		regulator-min-microvolt = <2700000>;
+		regulator-max-microvolt = <2700000>;
+		regulator-always-on;
+	};
+
+	soc: soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		compatible = "simple-bus";
+
+		l2: cache-controller@2040000 {
+			compatible = "arm,pl310-cache";
+			reg = <0x02040000 0x1000>;
+			arm,data-latency = <2 2 0>;
+			cache-unified;
+			cache-level = <2>;
+		};
+
+		intc: interrupt-controller@2000000 {
+			compatible = "qcom,msm-qgic2";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			reg = <0x02000000 0x1000>,
+			      <0x02002000 0x1000>;
+		};
+
+		timer@200a000 {
+			compatible = "qcom,kpss-wdt-mdm9615", "qcom,kpss-timer",
+				     "qcom,msm-timer";
+			interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_EDGE_RISING)>,
+				     <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_EDGE_RISING)>,
+				     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_EDGE_RISING)>;
+			reg = <0x0200a000 0x100>;
+			clock-frequency = <27000000>;
+			cpu-offset = <0x80000>;
+		};
+
+		msmgpio: pinctrl@800000 {
+			compatible = "qcom,mdm9615-pinctrl";
+			gpio-controller;
+			gpio-ranges = <&msmgpio 0 0 88>;
+			#gpio-cells = <2>;
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			reg = <0x800000 0x4000>;
+		};
+
+		gcc: clock-controller@900000 {
+			compatible = "qcom,gcc-mdm9615";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			reg = <0x900000 0x4000>;
+			clocks = <&cxo_board>,
+				 <&lcc PLL4>;
+		};
+
+		lcc: clock-controller@28000000 {
+			compatible = "qcom,lcc-mdm9615";
+			reg = <0x28000000 0x1000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			clocks = <&cxo_board>,
+				 <&gcc PLL4_VOTE>,
+				 <0>,
+				 <0>, <0>,
+				 <0>, <0>,
+				 <0>;
+			clock-names = "cxo",
+				      "pll4_vote",
+				      "mi2s_codec_clk",
+				      "codec_i2s_mic_codec_clk",
+				      "spare_i2s_mic_codec_clk",
+				      "codec_i2s_spkr_codec_clk",
+				      "spare_i2s_spkr_codec_clk",
+				      "pcm_codec_clk";
+		};
+
+		l2cc: clock-controller@2011000 {
+			compatible = "qcom,kpss-gcc-mdm9615", "qcom,kpss-gcc", "syscon";
+			reg = <0x02011000 0x1000>;
+		};
+
+		rng@1a500000 {
+			compatible = "qcom,prng";
+			reg = <0x1a500000 0x200>;
+			clocks = <&gcc PRNG_CLK>;
+			clock-names = "core";
+			assigned-clocks = <&gcc PRNG_CLK>;
+			assigned-clock-rates = <32000000>;
+		};
+
+		gsbi2: gsbi@16100000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <2>;
+			reg = <0x16100000 0x100>;
+			clocks = <&gcc GSBI2_H_CLK>;
+			clock-names = "iface";
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			gsbi2_i2c: i2c@16180000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x16180000 0x1000>;
+				interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+		};
+
+		gsbi3: gsbi@16200000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <3>;
+			reg = <0x16200000 0x100>;
+			clocks = <&gcc GSBI3_H_CLK>;
+			clock-names = "iface";
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			gsbi3_spi: spi@16280000 {
+				compatible = "qcom,spi-qup-v1.1.1";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x16280000 0x1000>;
+				interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GSBI3_QUP_CLK>, <&gcc GSBI3_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+		};
+
+		gsbi4: gsbi@16300000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <4>;
+			reg = <0x16300000 0x100>;
+			clocks = <&gcc GSBI4_H_CLK>;
+			clock-names = "iface";
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+
+			gsbi4_serial: serial@16340000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x16340000 0x1000>,
+				      <0x16300000 0x1000>;
+				interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+		};
+
+		gsbi5: gsbi@16400000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <5>;
+			reg = <0x16400000 0x100>;
+			clocks = <&gcc GSBI5_H_CLK>;
+			clock-names = "iface";
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+
+			gsbi5_i2c: i2c@16480000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x16480000 0x1000>;
+				interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+
+				/* QUP clock is not initialized, set rate */
+				assigned-clocks = <&gcc GSBI5_QUP_CLK>;
+				assigned-clock-rates = <24000000>;
+
+				clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+
+			gsbi5_serial: serial@16440000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x16440000 0x1000>,
+				      <0x16400000 0x1000>;
+				interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+		};
+
+		ssbi: ssbi@500000 {
+			compatible = "qcom,ssbi";
+			reg = <0x500000 0x1000>;
+			qcom,controller-type = "pmic-arbiter";
+		};
+
+		sdcc1bam: dma-controller@12182000 {
+			compatible = "qcom,bam-v1.3.0";
+			reg = <0x12182000 0x8000>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC1_H_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		sdcc2bam: dma-controller@12142000 {
+			compatible = "qcom,bam-v1.3.0";
+			reg = <0x12142000 0x8000>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC2_H_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		sdcc1: mmc@12180000 {
+			status = "disabled";
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00051180>;
+			reg = <0x12180000 0x2000>;
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <8>;
+			max-frequency = <48000000>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			vmmc-supply = <&vsdcc_fixed>;
+			dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
+			dma-names = "tx", "rx";
+			assigned-clocks = <&gcc SDC1_CLK>;
+			assigned-clock-rates = <400000>;
+		};
+
+		sdcc2: mmc@12140000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00051180>;
+			status = "disabled";
+			reg = <0x12140000 0x2000>;
+			interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC2_CLK>, <&gcc SDC2_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <48000000>;
+			no-1-8-v;
+			vmmc-supply = <&vsdcc_fixed>;
+			dmas = <&sdcc2bam 2>, <&sdcc2bam 1>;
+			dma-names = "tx", "rx";
+			assigned-clocks = <&gcc SDC2_CLK>;
+			assigned-clock-rates = <400000>;
+		};
+
+		tcsr: syscon@1a400000 {
+			compatible = "qcom,tcsr-mdm9615", "syscon";
+			reg = <0x1a400000 0x100>;
+		};
+
+		rpm: rpm@108000 {
+			compatible = "qcom,rpm-mdm9615";
+			reg = <0x108000 0x1000>;
+
+			qcom,ipc = <&l2cc 0x8 2>;
+
+			interrupts = <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "ack", "err", "wakeup";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-common.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-common.dtsi
new file mode 100644
index 000000000000..d4a32af0ef8f
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-common.dtsi
@@ -0,0 +1,361 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Common Board Device Tree for Microsoft MSM8x26-based Lumias
+ *
+ * Copyright (c) 2023, Jack Matthews <jm5112356@gmail.com>
+ * Copyright (c) 2023, Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
+ * Copyright (c) 2023, Dominik Kobinski <dominikkobinski314@gmail.com>
+ * Copyright (c) 2023, Rayyan Ansari <rayyan@ansari.sh>
+ */
+
+/*
+ * The .dts should first include qcom-msm8226.dtsi or msm8926.dtsi depending on
+ * the SoC on the given device.
+ */
+
+#include "pm8226.dtsi"
+#include <dt-bindings/input/input.h>
+
+/*
+ * Delete all generic (msm8226.dtsi) reserved
+ * memory mappings which are different on these devices.
+ */
+/delete-node/ &smem_region;
+
+/ {
+	aliases {
+		mmc0 = &sdhc_1; /* eMMC */
+		mmc1 = &sdhc_2; /* microSD */
+		display0 = &framebuffer;
+	};
+
+	chosen {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		stdout-path = "display0";
+
+		framebuffer: framebuffer@3200000 {
+			compatible = "simple-framebuffer";
+			reg = <0x3200000 0x800000>;
+			format = "a8r8g8b8";
+			width = <720>;
+			height = <1280>;
+			stride = <(720 * 4)>;
+
+			clocks = <&mmcc MDSS_AHB_CLK>,
+				 <&mmcc MDSS_AXI_CLK>,
+				 <&mmcc MDSS_BYTE0_CLK>,
+				 <&mmcc MDSS_MDP_CLK>,
+				 <&mmcc MDSS_PCLK0_CLK>,
+				 <&mmcc MDSS_VSYNC_CLK>;
+			power-domains = <&mmcc MDSS_GDSC>;
+		};
+	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&gpio_keys_default>;
+		pinctrl-names = "default";
+
+		label = "GPIO Buttons";
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+	};
+
+	/*
+	 * This device being a WP platform has a different
+	 * memory layout than other Android based devices.
+	 * This smem memory region is directly copied from
+	 * the original UEFI firmware.
+	 */
+	reserved-memory {
+		display_reserved: framebuffer@3200000 {
+			reg = <0x03200000 0x800000>;
+			no-map;
+		};
+
+		smem_region: smem@fa00000 {
+			reg = <0x0fa00000 0x100000>;
+			no-map;
+		};
+	};
+};
+
+&blsp1_i2c2 {
+	status = "okay";
+
+	magnetometer: magnetometer@c {
+		compatible = "asahi-kasei,ak09911";
+		reg = <0x0c>;
+
+		vdd-supply = <&pm8226_l15>;
+		vid-supply = <&pm8226_l6>;
+	};
+
+	accelerometer: accelerometer@1e {
+		compatible = "kionix,kx022-1020";
+		reg = <0x1e>;
+
+		interrupts-extended = <&tlmm 63 IRQ_TYPE_EDGE_RISING>;
+
+		vdd-supply = <&pm8226_l15>;
+		vddio-supply = <&pm8226_l6>;
+
+		mount-matrix = "1",  "0",  "0",
+			       "0", "-1",  "0",
+			       "0",  "0",  "1";
+	};
+};
+
+&blsp1_i2c5 {
+	status = "okay";
+
+	touchscreen: touchscreen@4b {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x4b>;
+
+		interrupts-extended = <&tlmm 17 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8226_l15>;
+		vio-supply = <&pm8226_l6>;
+
+		pinctrl-0 = <&touchscreen_default>;
+		pinctrl-names = "default";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmi4-f01@1 {
+			reg = <0x01>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f11@11 {
+			reg = <0x11>;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp1_uart3 {
+	status = "okay";
+};
+
+&pm8226_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+	status = "okay";
+};
+
+&pm8226_vib {
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-pm8226-regulators";
+
+		/* These values were taken from the original firmware DSDT */
+		pm8226_s1: s1 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8226_s3: s3 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8226_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2100000>;
+		};
+
+		pm8226_s5: s5 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l3: l3 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l5: l5 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l7: l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <1850000>;
+		};
+
+		pm8226_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		pm8226_l9: l9 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l14: l14 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+		};
+
+		pm8226_l15: l15 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8226_l16: l16 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8226_l17: l17 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+		};
+
+		pm8226_l18: l18 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+		};
+
+		pm8226_l19: l19 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8226_l20: l20 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+
+		pm8226_l21: l21 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l22: l22 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l24: l24 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8226_l25: l25 {
+			regulator-min-microvolt = <1775000>;
+			regulator-max-microvolt = <2075000>;
+		};
+
+		pm8226_l27: l27 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l28: l28 {
+			regulator-min-microvolt = <2000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&pm8226_l17>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	status = "okay";
+};
+
+&sdhc_2 {
+	vmmc-supply = <&pm8226_l18>;
+	vqmmc-supply = <&pm8226_l21>;
+
+	status = "okay";
+};
+
+&smbb {
+	status = "okay";
+};
+
+&usb {
+	extcon = <&smbb>;
+	dr_mode = "peripheral";
+
+	status = "okay";
+};
+
+&usb_hs_phy {
+	extcon = <&smbb>;
+	v1p8-supply = <&pm8226_l10>;
+	v3p3-supply = <&pm8226_l20>;
+};
+
+&tlmm {
+	gpio_keys_default: gpio-keys-default-state {
+		pins = "gpio106", "gpio107", "gpio108";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	touchscreen_default: touchscreen-default-state {
+		irq-pins {
+			pins = "gpio17";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		reset-pins {
+			pins = "gpio16";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-disable;
+			output-high;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-dempsey.dts b/arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-dempsey.dts
new file mode 100644
index 000000000000..f448c9088416
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-dempsey.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023, Jack Matthews <jm5112356@gmail.com>
+ * Copyright (c) 2023, Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
+ * Copyright (c) 2023, Dominik Kobinski <dominikkobinski314@gmail.com>
+ * Copyright (c) 2023, Rayyan Ansari <rayyan@ansari.sh>
+ */
+
+/dts-v1/;
+
+#include "qcom-msm8226.dtsi"
+#include "qcom-msm8226-microsoft-common.dtsi"
+
+/ {
+	model = "Microsoft Lumia 640";
+	compatible = "microsoft,dempsey", "qcom,msm8226";
+	chassis-type = "handset";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-makepeace.dts b/arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-makepeace.dts
new file mode 100644
index 000000000000..94bf3b1ad1bd
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-makepeace.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023, Jack Matthews <jm5112356@gmail.com>
+ * Copyright (c) 2023, Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
+ * Copyright (c) 2023, Dominik Kobinski <dominikkobinski314@gmail.com>
+ * Copyright (c) 2023, Rayyan Ansari <rayyan@ansari.sh>
+ */
+
+/dts-v1/;
+
+#include "qcom-msm8226.dtsi"
+#include "qcom-msm8226-microsoft-common.dtsi"
+
+/ {
+	model = "Microsoft Lumia 640 XL";
+	compatible = "microsoft,makepeace", "qcom,msm8226";
+	chassis-type = "handset";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-moneypenny.dts b/arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-moneypenny.dts
new file mode 100644
index 000000000000..d8cdb75dfbb8
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8226-microsoft-moneypenny.dts
@@ -0,0 +1,27 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023, Jack Matthews <jm5112356@gmail.com>
+ * Copyright (c) 2023, Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
+ * Copyright (c) 2023, Dominik Kobinski <dominikkobinski314@gmail.com>
+ * Copyright (c) 2023, Rayyan Ansari <rayyan@ansari.sh>
+ */
+
+/dts-v1/;
+
+#include "qcom-msm8226.dtsi"
+#include "qcom-msm8226-microsoft-common.dtsi"
+
+/* This device has no magnetometer */
+/delete-node/ &magnetometer;
+
+/ {
+	model = "Nokia Lumia 630";
+	compatible = "microsoft,moneypenny", "qcom,msm8226";
+	chassis-type = "handset";
+};
+
+&framebuffer {
+	width = <480>;
+	height = <854>;
+	stride = <(480 * 4)>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-matisse-common.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-matisse-common.dtsi
new file mode 100644
index 000000000000..f1544a7e8369
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-matisse-common.dtsi
@@ -0,0 +1,470 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Matti Lehtimäki <matti.lehtimaki@gmail.com>
+ */
+
+/*
+ * The .dts should first include qcom-msm8226.dtsi or msm8926.dtsi depending on
+ * the SoC on the given device.
+ */
+
+#include <dt-bindings/input/input.h>
+#include "pm8226.dtsi"
+
+/delete-node/ &adsp_region;
+/delete-node/ &mba_region;
+/delete-node/ &mpss_region;
+/delete-node/ &smem_region;
+
+/ {
+	aliases {
+		mmc0 = &sdhc_1; /* SDC1 eMMC slot */
+		mmc1 = &sdhc_2; /* SDC2 SD card slot */
+		display0 = &framebuffer0;
+	};
+
+	chosen {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		stdout-path = "display0";
+
+		framebuffer0: framebuffer@3200000 {
+			compatible = "simple-framebuffer";
+			reg = <0x03200000 0x800000>;
+			width = <1280>;
+			height = <800>;
+			stride = <(1280 * 3)>;
+			format = "r8g8b8";
+		};
+	};
+
+	gpio-hall-sensor {
+		compatible = "gpio-keys";
+
+		event-hall-sensor {
+			label = "Hall Effect Sensor";
+			gpios = <&tlmm 110 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			debounce-interval = <15>;
+			linux,can-disable;
+			wakeup-source;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		key-home {
+			label = "Home";
+			gpios = <&tlmm 108 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOMEPAGE>;
+			debounce-interval = <15>;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <15>;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <15>;
+		};
+	};
+
+	i2c-backlight {
+		compatible = "i2c-gpio";
+		sda-gpios = <&tlmm 20 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&tlmm 21 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+
+		pinctrl-0 = <&backlight_i2c_default_state>;
+		pinctrl-names = "default";
+
+		i2c-gpio,delay-us = <4>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		backlight@2c {
+			compatible = "ti,lp8556";
+			reg = <0x2c>;
+
+			dev-ctrl = /bits/ 8 <0x80>;
+			init-brt = /bits/ 8 <0x3f>;
+
+			pwms = <&backlight_pwm 0 100000>;
+			pwm-names = "lp8556";
+
+			rom-a0h {
+				rom-addr = /bits/ 8 <0xa0>;
+				rom-val = /bits/ 8 <0x44>;
+			};
+
+			rom-a1h {
+				rom-addr = /bits/ 8 <0xa1>;
+				rom-val = /bits/ 8 <0x6c>;
+			};
+
+			rom-a5h {
+				rom-addr = /bits/ 8 <0xa5>;
+				rom-val = /bits/ 8 <0x24>;
+			};
+		};
+	};
+
+	backlight_pwm: pwm {
+		compatible = "clk-pwm";
+		#pwm-cells = <2>;
+		clocks = <&mmcc CAMSS_GP0_CLK>;
+		pinctrl-0 = <&backlight_pwm_default_state>;
+		pinctrl-names = "default";
+	};
+
+	reg_tsp_1p8v: regulator-tsp-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "tsp_1p8v";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&tlmm 31 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_en_default_state>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		framebuffer@3200000 {
+			reg = <0x03200000 0x800000>;
+			no-map;
+		};
+
+		mpss_region: mpss@8400000 {
+			reg = <0x08400000 0x1f00000>;
+			no-map;
+		};
+
+		mba_region: mba@a300000 {
+			reg = <0x0a300000 0x100000>;
+			no-map;
+		};
+
+		reserved@cb00000 {
+			reg = <0x0cb00000 0x700000>;
+			no-map;
+		};
+
+		wcnss@d200000 {
+			reg = <0x0d200000 0x700000>;
+			no-map;
+		};
+
+		adsp_region: adsp@d900000 {
+			reg = <0x0d900000 0x1800000>;
+			no-map;
+		};
+
+		venus@f100000 {
+			reg = <0x0f100000 0x500000>;
+			no-map;
+		};
+
+		smem_region: smem@fa00000 {
+			reg = <0x0fa00000 0x100000>;
+			no-map;
+		};
+
+		reserved@fb00000 {
+			reg = <0x0fb00000 0x260000>;
+			no-map;
+		};
+
+		rfsa@fd60000 {
+			reg = <0x0fd60000 0x20000>;
+			no-map;
+		};
+
+		rmtfs@fd80000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0x0fd80000 0x180000>;
+			no-map;
+
+			qcom,client-id = <1>;
+		};
+	};
+};
+
+&adsp {
+	status = "okay";
+};
+
+&blsp1_i2c4 {
+	status = "okay";
+
+	muic: usb-switch@25 {
+		compatible = "siliconmitus,sm5502-muic";
+		reg = <0x25>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <67 IRQ_TYPE_EDGE_FALLING>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&muic_int_default_state>;
+	};
+};
+
+&blsp1_uart3 {
+	status = "okay";
+};
+
+&modem {
+	mx-supply = <&pm8226_l3>;
+	pll-supply = <&pm8226_l8>;
+
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-pm8226-regulators";
+
+		pm8226_s3: s3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8226_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2200000>;
+		};
+
+		pm8226_s5: s5 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8226_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l3: l3 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1350000>;
+			regulator-always-on;
+		};
+
+		pm8226_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l5: l5 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		pm8226_l7: l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <1850000>;
+		};
+
+		pm8226_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		pm8226_l9: l9 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l14: l14 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+		};
+
+		pm8226_l15: l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8226_l16: l16 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3350000>;
+		};
+
+		pm8226_l17: l17 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+			regulator-always-on;
+		};
+
+		pm8226_l18: l18 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l19: l19 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8226_l20: l20 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+
+		pm8226_l21: l21 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l22: l22 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8226_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8226_l24: l24 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8226_l25: l25 {
+			regulator-min-microvolt = <1775000>;
+			regulator-max-microvolt = <2125000>;
+		};
+
+		pm8226_l26: l26 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8226_l27: l27 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l28: l28 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_lvs1: lvs1 {};
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&pm8226_l17>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	bus-width = <8>;
+	non-removable;
+
+	status = "okay";
+};
+
+&sdhc_2 {
+	vmmc-supply = <&pm8226_l18>;
+	vqmmc-supply = <&pm8226_l21>;
+
+	bus-width = <4>;
+	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+
+	status = "okay";
+};
+
+&tlmm {
+	accel_int_default_state: accel-int-default-state {
+		pins = "gpio54";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	backlight_i2c_default_state: backlight-i2c-default-state {
+		pins = "gpio20", "gpio21";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	backlight_pwm_default_state: backlight-pwm-default-state {
+		pins = "gpio33";
+		function = "gp0_clk";
+	};
+
+	muic_int_default_state: muic-int-default-state {
+		pins = "gpio67";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tsp_en_default_state: tsp-en-default-state {
+		pins = "gpio31";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tsp_int_rst_default_state: tsp-int-rst-default-state {
+		pins = "gpio17";
+		function = "gpio";
+		drive-strength = <10>;
+		bias-pull-up;
+	};
+};
+
+&usb {
+	extcon = <&muic>, <&muic>;
+	status = "okay";
+};
+
+&usb_hs_phy {
+	extcon = <&muic>;
+	v1p8-supply = <&pm8226_l10>;
+	v3p3-supply = <&pm8226_l20>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-ms013g.dts b/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-ms013g.dts
new file mode 100644
index 000000000000..08b50dc63923
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-ms013g.dts
@@ -0,0 +1,388 @@
+// SPDX-License-Identifier: BSD-3-Clause
+
+/dts-v1/;
+
+#include "qcom-msm8226.dtsi"
+#include "pm8226.dtsi"
+
+/delete-node/ &smem_region;
+
+/ {
+	model = "Samsung Galaxy Grand 2";
+	compatible = "samsung,ms013g", "qcom,msm8226";
+	chassis-type = "handset";
+
+	aliases {
+		mmc0 = &sdhc_1; /* SDC1 eMMC slot */
+		mmc1 = &sdhc_2; /* SDC2 SD card slot */
+		serial0 = &blsp1_uart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-hall-sensor {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&gpio_hall_sensor_default>;
+		pinctrl-names = "default";
+
+		label = "GPIO Hall Effect Sensor";
+
+		event-hall-sensor {
+			label = "Hall Effect Sensor";
+			gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			linux,can-disable;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&gpio_keys_default>;
+		pinctrl-names = "default";
+
+		label = "GPIO Buttons";
+
+		button-volume-up {
+			label = "Volume Up";
+			gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		button-volume-down {
+			label = "Volume Down";
+			gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+
+		button-home {
+			label = "Home Key";
+			gpios = <&tlmm 108 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOMEPAGE>;
+		};
+	};
+
+	reg_motor_vdd: regulator-motor-vdd {
+		compatible = "regulator-fixed";
+		regulator-name = "motor_vdd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 111 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&motor_en_default>;
+		pinctrl-names = "default";
+	};
+
+	reg_vdd_tsp_a: regulator-vdd-tsp-a {
+		compatible = "regulator-fixed";
+		regulator-name = "tsp_3p3v";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 31 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&tsp_en_default>;
+		pinctrl-names = "default";
+	};
+
+	reserved-memory {
+		smem_region: smem@fa00000 {
+			reg = <0x0fa00000 0x100000>;
+			no-map;
+		};
+	};
+
+	vibrator {
+		compatible = "regulator-haptic";
+		haptic-supply = <&reg_motor_vdd>;
+		min-microvolt = <3300000>;
+		max-microvolt = <3300000>;
+	};
+};
+
+&blsp1_i2c2 {
+	status = "okay";
+
+	accelerometer@18 {
+		compatible = "bosch,bma255";
+		reg = <0x18>;
+		interrupts-extended = <&tlmm 64 IRQ_TYPE_EDGE_RISING>;
+
+		vdd-supply = <&pm8226_l19>;
+		vddio-supply = <&pm8226_lvs1>;
+
+		pinctrl-0 = <&accel_int_default>;
+		pinctrl-names = "default";
+
+		mount-matrix = "0", "1", "0",
+			       "-1", "0", "0",
+			       "0", "0", "-1";
+	};
+};
+
+&blsp1_i2c5 {
+	status = "okay";
+
+	touchscreen@20 {
+		compatible = "zinitix,bt541";
+
+		reg = <0x20>;
+		interrupts-extended = <&tlmm 17 IRQ_TYPE_EDGE_FALLING>;
+
+		touchscreen-size-x = <720>;
+		touchscreen-size-y = <1280>;
+
+		vcca-supply = <&reg_vdd_tsp_a>;
+		vdd-supply = <&pm8226_lvs1>;
+
+		pinctrl-0 = <&tsp_int_default>;
+		pinctrl-names = "default";
+
+		linux,keycodes = <KEY_APPSELECT KEY_BACK>;
+	};
+};
+
+&blsp1_uart3 {
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-pm8226-regulators";
+
+		pm8226_s3: s3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8226_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2200000>;
+		};
+
+		pm8226_s5: s5 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8226_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l3: l3 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1337500>;
+		};
+
+		pm8226_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l5: l5 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-allow-set-load;
+			regulator-always-on;
+		};
+
+		pm8226_l7: l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <1850000>;
+		};
+
+		pm8226_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l9: l9 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l14: l14 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+		};
+
+		pm8226_l15: l15 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+
+		pm8226_l16: l16 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3350000>;
+		};
+
+		pm8226_l17: l17 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+			regulator-always-on;
+		};
+
+		pm8226_l18: l18 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l19: l19 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8226_l20: l20 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+
+		pm8226_l21: l21 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-allow-set-load;
+		};
+
+		pm8226_l22: l22 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8226_l24: l24 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8226_l25: l25 {
+			regulator-min-microvolt = <1775000>;
+			regulator-max-microvolt = <2125000>;
+		};
+
+		pm8226_l26: l26 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8226_l27: l27 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l28: l28 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_lvs1: lvs1 {};
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&pm8226_l17>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	bus-width = <8>;
+	non-removable;
+
+	status = "okay";
+};
+
+&sdhc_2 {
+	vmmc-supply = <&pm8226_l18>;
+	vqmmc-supply = <&pm8226_l21>;
+
+	bus-width = <4>;
+	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+
+	pinctrl-0 = <&sdhc2_default_state &sdhc2_cd_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&tlmm {
+	accel_int_default: accel-int-default-state {
+		pins = "gpio64";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	gpio_hall_sensor_default: gpio-hall-sensor-default-state {
+		pins = "gpio50";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	gpio_keys_default: gpio-keys-default-state {
+		pins = "gpio106", "gpio107", "gpio108";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	motor_en_default: motor-en-default-state {
+		pins = "gpio111";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	sdhc2_cd_default: sdhc2-cd-default-state {
+		pins = "gpio38";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tsp_en_default: tsp-en-default-state {
+		pins = "gpio31";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tsp_int_default: tsp-int-default-state {
+		pins = "gpio17";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
diff --git a/arch/arm/boot/dts/qcom-msm8226-samsung-s3ve3g.dts b/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-s3ve3g.dts
index d159188c8b95..288cacd5d1fa 100644
--- a/arch/arm/boot/dts/qcom-msm8226-samsung-s3ve3g.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-s3ve3g.dts
@@ -8,6 +8,7 @@
 / {
 	model = "Samsung Galaxy S III Neo";
 	compatible = "samsung,s3ve3g", "qcom,msm8226";
+	chassis-type = "handset";
 
 	aliases {
 		serial0 = &blsp1_uart3;
@@ -18,8 +19,6 @@
 	};
 };
 
-&soc {
-	serial@f991f000 {
-		status = "ok";
-	};
+&blsp1_uart3 {
+	status = "okay";
 };
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8226.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8226.dtsi
new file mode 100644
index 000000000000..51a7a3fb36d8
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8226.dtsi
@@ -0,0 +1,1488 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2020, The Linux Foundation. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,dsi-phy-28nm.h>
+#include <dt-bindings/clock/qcom,gcc-msm8974.h>
+#include <dt-bindings/clock/qcom,mmcc-msm8974.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+#include <dt-bindings/reset/qcom,gcc-msm8974.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&intc>;
+
+	chosen { };
+
+	clocks {
+		xo_board: xo_board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <19200000>;
+		};
+
+		sleep_clk: sleep_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a7";
+			enable-method = "qcom,msm8226-smp";
+			device_type = "cpu";
+			reg = <0>;
+			next-level-cache = <&l2>;
+			clocks = <&apcs>;
+			operating-points-v2 = <&cpu_opp_table>;
+			qcom,acc = <&acc0>;
+			qcom,saw = <&saw0>;
+			#cooling-cells = <2>;
+		};
+
+		cpu1: cpu@1 {
+			compatible = "arm,cortex-a7";
+			enable-method = "qcom,msm8226-smp";
+			device_type = "cpu";
+			reg = <1>;
+			next-level-cache = <&l2>;
+			clocks = <&apcs>;
+			operating-points-v2 = <&cpu_opp_table>;
+			qcom,acc = <&acc1>;
+			qcom,saw = <&saw1>;
+			#cooling-cells = <2>;
+		};
+
+		cpu2: cpu@2 {
+			compatible = "arm,cortex-a7";
+			enable-method = "qcom,msm8226-smp";
+			device_type = "cpu";
+			reg = <2>;
+			next-level-cache = <&l2>;
+			clocks = <&apcs>;
+			operating-points-v2 = <&cpu_opp_table>;
+			qcom,acc = <&acc2>;
+			qcom,saw = <&saw2>;
+			#cooling-cells = <2>;
+		};
+
+		cpu3: cpu@3 {
+			compatible = "arm,cortex-a7";
+			enable-method = "qcom,msm8226-smp";
+			device_type = "cpu";
+			reg = <3>;
+			next-level-cache = <&l2>;
+			clocks = <&apcs>;
+			operating-points-v2 = <&cpu_opp_table>;
+			qcom,acc = <&acc3>;
+			qcom,saw = <&saw3>;
+			#cooling-cells = <2>;
+		};
+
+		l2: l2-cache {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	firmware {
+		scm {
+			compatible = "qcom,scm-msm8226", "qcom,scm";
+			clocks = <&gcc GCC_CE1_CLK>, <&gcc GCC_CE1_AXI_CLK>, <&gcc GCC_CE1_AHB_CLK>;
+			clock-names = "core", "bus", "iface";
+		};
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0>;
+	};
+
+	cpu_opp_table: opp-table-cpu {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-300000000 {
+			opp-hz = /bits/ 64 <300000000>;
+		};
+
+		opp-384000000 {
+			opp-hz = /bits/ 64 <384000000>;
+		};
+
+		opp-600000000 {
+			opp-hz = /bits/ 64 <600000000>;
+		};
+
+		opp-787200000 {
+			opp-hz = /bits/ 64 <787200000>;
+		};
+
+		/* Higher CPU frequencies need speedbin support */
+	};
+
+	pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) |
+					 IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	rpm: remoteproc {
+		compatible = "qcom,msm8226-rpm-proc", "qcom,rpm-proc";
+
+		master-stats {
+			compatible = "qcom,rpm-master-stats";
+			qcom,rpm-msg-ram = <&apss_master_stats>,
+					   <&mpss_master_stats>,
+					   <&lpss_master_stats>,
+					   <&pronto_master_stats>;
+			qcom,master-names = "APSS",
+					    "MPSS",
+					    "LPSS",
+					    "PRONTO";
+		};
+
+		smd-edge {
+			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
+			mboxes = <&apcs 0>;
+			qcom,smd-edge = <15>;
+
+			rpm_requests: rpm-requests {
+				compatible = "qcom,rpm-msm8226", "qcom,smd-rpm";
+				qcom,smd-channels = "rpm_requests";
+
+				rpmcc: clock-controller {
+					compatible = "qcom,rpmcc-msm8226", "qcom,rpmcc";
+					#clock-cells = <1>;
+					clocks = <&xo_board>;
+					clock-names = "xo";
+				};
+
+				rpmpd: power-controller {
+					compatible = "qcom,msm8226-rpmpd";
+					#power-domain-cells = <1>;
+					operating-points-v2 = <&rpmpd_opp_table>;
+
+					rpmpd_opp_table: opp-table {
+						compatible = "operating-points-v2";
+
+						rpmpd_opp_ret: opp1 {
+							opp-level = <1>;
+						};
+						rpmpd_opp_svs_krait: opp2 {
+							opp-level = <2>;
+						};
+						rpmpd_opp_svs_soc: opp3 {
+							opp-level = <3>;
+						};
+						rpmpd_opp_nom: opp4 {
+							opp-level = <4>;
+						};
+						rpmpd_opp_turbo: opp5 {
+							opp-level = <5>;
+						};
+						rpmpd_opp_super_turbo: opp6 {
+							opp-level = <6>;
+						};
+					};
+				};
+			};
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		smem_region: smem@3000000 {
+			reg = <0x3000000 0x100000>;
+			no-map;
+		};
+
+		mpss_region: mpss@8000000 {
+			reg = <0x08000000 0x5100000>;
+			no-map;
+			status = "disabled";
+		};
+
+		mba_region: mba@d100000 {
+			reg = <0x0d100000 0x100000>;
+			no-map;
+			status = "disabled";
+		};
+
+		adsp_region: adsp@dc00000 {
+			reg = <0x0dc00000 0x1900000>;
+			no-map;
+		};
+	};
+
+	smem {
+		compatible = "qcom,smem";
+
+		memory-region = <&smem_region>;
+		qcom,rpm-msg-ram = <&rpm_msg_ram>;
+
+		hwlocks = <&tcsr_mutex 3>;
+	};
+
+	smp2p-adsp {
+		compatible = "qcom,smp2p";
+		qcom,smem = <443>, <429>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <GIC_SPI 158 IRQ_TYPE_EDGE_RISING>;
+
+		mboxes = <&apcs 10>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <2>;
+
+		adsp_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		adsp_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smp2p-modem {
+		compatible = "qcom,smp2p";
+		qcom,smem = <435>, <428>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>;
+
+		mboxes = <&apcs 14>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <1>;
+
+		modem_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		modem_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smsm {
+		compatible = "qcom,smsm";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mboxes = <0>, <&apcs 13>, <&apcs 9>, <&apcs 19>;
+
+		apps_smsm: apps@0 {
+			reg = <0>;
+			#qcom,smem-state-cells = <1>;
+		};
+
+		modem_smsm: modem@1 {
+			reg = <1>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		adsp_smsm: adsp@2 {
+			reg = <2>;
+			interrupts = <GIC_SPI 157 IRQ_TYPE_EDGE_RISING>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		wcnss_smsm: wcnss@7 {
+			reg = <7>;
+			interrupts = <GIC_SPI 144 IRQ_TYPE_EDGE_RISING>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	soc: soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		intc: interrupt-controller@f9000000 {
+			compatible = "qcom,msm-qgic2";
+			reg = <0xf9000000 0x1000>,
+			      <0xf9002000 0x1000>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+		};
+
+		apcs: mailbox@f9011000 {
+			compatible = "qcom,msm8226-apcs-kpss-global",
+				     "qcom,msm8916-apcs-kpss-global", "syscon";
+			reg = <0xf9011000 0x1000>;
+			#mbox-cells = <1>;
+			clocks = <&a7pll>, <&gcc GPLL0_VOTE>;
+			clock-names = "pll", "aux";
+			#clock-cells = <0>;
+		};
+
+		a7pll: clock@f9016000 {
+			compatible = "qcom,msm8226-a7pll";
+			reg = <0xf9016000 0x40>;
+			#clock-cells = <0>;
+			clocks = <&xo_board>;
+			clock-names = "xo";
+			operating-points-v2 = <&a7pll_opp_table>;
+
+			a7pll_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-768000000 {
+					opp-hz = /bits/ 64 <768000000>;
+				};
+
+				opp-787200000 {
+					opp-hz = /bits/ 64 <787200000>;
+				};
+
+				opp-998400000 {
+					opp-hz = /bits/ 64 <998400000>;
+				};
+
+				opp-1094400000 {
+					opp-hz = /bits/ 64 <1094400000>;
+				};
+
+				opp-1190400000 {
+					opp-hz = /bits/ 64 <1190400000>;
+				};
+
+				opp-1305600000 {
+					opp-hz = /bits/ 64 <1305600000>;
+				};
+
+				opp-1344000000 {
+					opp-hz = /bits/ 64 <1344000000>;
+				};
+
+				opp-1401600000 {
+					opp-hz = /bits/ 64 <1401600000>;
+				};
+
+				opp-1497600000 {
+					opp-hz = /bits/ 64 <1497600000>;
+				};
+
+				opp-1593600000 {
+					opp-hz = /bits/ 64 <1593600000>;
+				};
+
+				opp-1689600000 {
+					opp-hz = /bits/ 64 <1689600000>;
+				};
+
+				opp-1785600000 {
+					opp-hz = /bits/ 64 <1785600000>;
+				};
+			};
+		};
+
+		saw_l2: power-manager@f9012000 {
+			compatible = "qcom,msm8226-saw2-v2.1-l2", "qcom,saw2";
+			reg = <0xf9012000 0x1000>;
+		};
+
+		watchdog@f9017000 {
+			compatible = "qcom,apss-wdt-msm8226", "qcom,kpss-wdt";
+			reg = <0xf9017000 0x1000>;
+			interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 4 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&sleep_clk>;
+		};
+
+		timer@f9020000 {
+			compatible = "arm,armv7-timer-mem";
+			reg = <0xf9020000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			frame@f9021000 {
+				frame-number = <0>;
+				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9021000 0x1000>,
+				      <0xf9022000 0x1000>;
+			};
+
+			frame@f9023000 {
+				frame-number = <1>;
+				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9023000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9024000 {
+				frame-number = <2>;
+				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9024000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9025000 {
+				frame-number = <3>;
+				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9025000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9026000 {
+				frame-number = <4>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9026000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9027000 {
+				frame-number = <5>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9027000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@f9028000 {
+				frame-number = <6>;
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xf9028000 0x1000>;
+				status = "disabled";
+			};
+		};
+
+		acc0: power-manager@f9088000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0xf9088000 0x1000>, <0xf9008000 0x1000>;
+		};
+
+		saw0: power-manager@f9089000 {
+			compatible = "qcom,msm8226-saw2-v2.1-cpu", "qcom,saw2";
+			reg = <0xf9089000 0x1000>;
+		};
+
+		acc1: power-manager@f9098000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0xf9098000 0x1000>, <0xf9008000 0x1000>;
+		};
+
+		saw1: power-manager@f9099000 {
+			compatible = "qcom,msm8226-saw2-v2.1-cpu", "qcom,saw2";
+			reg = <0xf9099000 0x1000>;
+		};
+
+		acc2: power-manager@f90a8000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0xf90a8000 0x1000>, <0xf9008000 0x1000>;
+		};
+
+		saw2: power-manager@f90a9000 {
+			compatible = "qcom,msm8226-saw2-v2.1-cpu", "qcom,saw2";
+			reg = <0xf90a9000 0x1000>;
+		};
+
+		acc3: power-manager@f90b8000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0xf90b8000 0x1000>, <0xf9008000 0x1000>;
+		};
+
+		saw3: power-manager@f90b9000 {
+			compatible = "qcom,msm8226-saw2-v2.1-cpu", "qcom,saw2";
+			reg = <0xf90b9000 0x1000>;
+		};
+
+		sdhc_1: mmc@f9824900 {
+			compatible = "qcom,msm8226-sdhci", "qcom,sdhci-msm-v4";
+			reg = <0xf9824900 0x11c>, <0xf9824000 0x800>;
+			reg-names = "hc", "core";
+			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
+				 <&rpmcc RPM_SMD_XO_CLK_SRC>;
+			clock-names = "iface", "core", "xo";
+			pinctrl-names = "default";
+			pinctrl-0 = <&sdhc1_default_state>;
+			status = "disabled";
+		};
+
+		sdhc_3: mmc@f9864900 {
+			compatible = "qcom,msm8226-sdhci", "qcom,sdhci-msm-v4";
+			reg = <0xf9864900 0x11c>, <0xf9864000 0x800>;
+			reg-names = "hc", "core";
+			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC3_AHB_CLK>,
+				 <&gcc GCC_SDCC3_APPS_CLK>,
+				 <&rpmcc RPM_SMD_XO_CLK_SRC>;
+			clock-names = "iface", "core", "xo";
+			pinctrl-names = "default";
+			pinctrl-0 = <&sdhc3_default_state>;
+			status = "disabled";
+		};
+
+		sdhc_2: mmc@f98a4900 {
+			compatible = "qcom,msm8226-sdhci", "qcom,sdhci-msm-v4";
+			reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>;
+			reg-names = "hc", "core";
+			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>,
+				 <&rpmcc RPM_SMD_XO_CLK_SRC>;
+			clock-names = "iface", "core", "xo";
+			pinctrl-names = "default";
+			pinctrl-0 = <&sdhc2_default_state>;
+			status = "disabled";
+		};
+
+		blsp1_uart1: serial@f991d000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0xf991d000 0x1000>;
+			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
+		blsp1_uart2: serial@f991e000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0xf991e000 0x1000>;
+			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core",
+				      "iface";
+			status = "disabled";
+		};
+
+		blsp1_uart3: serial@f991f000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0xf991f000 0x1000>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
+		blsp1_uart4: serial@f9920000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0xf9920000 0x1000>;
+			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART4_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
+		blsp1_i2c1: i2c@f9923000 {
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9923000 0x1000>;
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_i2c1_pins>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp1_i2c2: i2c@f9924000 {
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9924000 0x1000>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_i2c2_pins>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp1_i2c3: i2c@f9925000 {
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9925000 0x1000>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_i2c3_pins>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp1_i2c4: i2c@f9926000 {
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9926000 0x1000>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_i2c4_pins>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp1_i2c5: i2c@f9927000 {
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9927000 0x1000>;
+			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_i2c5_pins>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		blsp1_i2c6: i2c@f9928000 {
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9928000 0x1000>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core",
+				      "iface";
+			pinctrl-0 = <&blsp1_i2c6_pins>;
+			pinctrl-names = "default";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		usb: usb@f9a55000 {
+			compatible = "qcom,ci-hdrc";
+			reg = <0xf9a55000 0x200>,
+			      <0xf9a55200 0x200>;
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_USB_HS_AHB_CLK>,
+				 <&gcc GCC_USB_HS_SYSTEM_CLK>;
+			clock-names = "iface", "core";
+			assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>;
+			assigned-clock-rates = <75000000>;
+			resets = <&gcc GCC_USB_HS_BCR>;
+			reset-names = "core";
+			phy_type = "ulpi";
+			dr_mode = "otg";
+			hnp-disable;
+			srp-disable;
+			adp-disable;
+			ahb-burst-config = <0>;
+			phy-names = "usb-phy";
+			phys = <&usb_hs_phy>;
+			status = "disabled";
+			#reset-cells = <1>;
+
+			ulpi {
+				usb_hs_phy: phy {
+					compatible = "qcom,usb-hs-phy-msm8226",
+						     "qcom,usb-hs-phy";
+					#phy-cells = <0>;
+					clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
+						 <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
+					clock-names = "ref", "sleep";
+					resets = <&gcc GCC_USB2A_PHY_BCR>, <&usb 0>;
+					reset-names = "phy", "por";
+					qcom,init-seq = /bits/ 8 <0x0 0x44
+						0x1 0x68 0x2 0x24 0x3 0x13>;
+				};
+			};
+		};
+
+		rng@f9bff000 {
+			compatible = "qcom,prng";
+			reg = <0xf9bff000 0x200>;
+			clocks = <&gcc GCC_PRNG_AHB_CLK>;
+			clock-names = "core";
+		};
+
+		sram@fc190000 {
+			compatible = "qcom,msm8226-rpm-stats";
+			reg = <0xfc190000 0x10000>;
+		};
+
+		gcc: clock-controller@fc400000 {
+			compatible = "qcom,gcc-msm8226";
+			reg = <0xfc400000 0x4000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+
+			clocks = <&xo_board>,
+				 <&sleep_clk>;
+			clock-names = "xo",
+				      "sleep_clk";
+		};
+
+		rpm_msg_ram: sram@fc428000 {
+			compatible = "qcom,rpm-msg-ram";
+			reg = <0xfc428000 0x4000>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0xfc428000 0x4000>;
+
+			apss_master_stats: sram@150 {
+				reg = <0x150 0x14>;
+			};
+
+			mpss_master_stats: sram@b50 {
+				reg = <0xb50 0x14>;
+			};
+
+			lpss_master_stats: sram@1550 {
+				reg = <0x1550 0x14>;
+			};
+
+			pronto_master_stats: sram@1f50 {
+				reg = <0x1f50 0x14>;
+			};
+		};
+
+		tsens: thermal-sensor@fc4a9000 {
+			compatible = "qcom,msm8226-tsens", "qcom,tsens-v0_1";
+			reg = <0xfc4a9000 0x1000>, /* TM */
+			      <0xfc4a8000 0x1000>; /* SROT */
+			nvmem-cells = <&tsens_mode>,
+				      <&tsens_base1>, <&tsens_base2>,
+				      <&tsens_s0_p1>, <&tsens_s0_p2>,
+				      <&tsens_s1_p1>, <&tsens_s1_p2>,
+				      <&tsens_s2_p1>, <&tsens_s2_p2>,
+				      <&tsens_s3_p1>, <&tsens_s3_p2>,
+				      <&tsens_s4_p1>, <&tsens_s4_p2>,
+				      <&tsens_s5_p1>, <&tsens_s5_p2>,
+				      <&tsens_s6_p1>, <&tsens_s6_p2>;
+			nvmem-cell-names = "mode",
+					   "base1", "base2",
+					   "s0_p1", "s0_p2",
+					   "s1_p1", "s1_p2",
+					   "s2_p1", "s2_p2",
+					   "s3_p1", "s3_p2",
+					   "s4_p1", "s4_p2",
+					   "s5_p1", "s5_p2",
+					   "s6_p1", "s6_p2";
+			#qcom,sensors = <6>;
+			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow";
+			#thermal-sensor-cells = <1>;
+		};
+
+		restart@fc4ab000 {
+			compatible = "qcom,pshold";
+			reg = <0xfc4ab000 0x4>;
+		};
+
+		qfprom: efuse@fc4bc000 {
+			compatible = "qcom,msm8226-qfprom", "qcom,qfprom";
+			reg = <0xfc4bc000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			tsens_base1: base1@1c1 {
+				reg = <0x1c1 0x2>;
+				bits = <5 8>;
+			};
+
+			tsens_s0_p1: s0-p1@1c2 {
+				reg = <0x1c2 0x2>;
+				bits = <5 6>;
+			};
+
+			tsens_s1_p1: s1-p1@1c4 {
+				reg = <0x1c4 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s2_p1: s2-p1@1c4 {
+				reg = <0x1c4 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s3_p1: s3-p1@1c5 {
+				reg = <0x1c5 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s4_p1: s4-p1@1c6 {
+				reg = <0x1c6 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s5_p1: s5-p1@1c7 {
+				reg = <0x1c7 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s6_p1: s6-p1@1ca {
+				reg = <0x1ca 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_base2: base2@1cc {
+				reg = <0x1cc 0x1>;
+				bits = <0 8>;
+			};
+
+			tsens_s0_p2: s0-p2@1cd {
+				reg = <0x1cd 0x1>;
+				bits = <0 6>;
+			};
+
+			tsens_s1_p2: s1-p2@1cd {
+				reg = <0x1cd 0x2>;
+				bits = <6 6>;
+			};
+
+			tsens_s2_p2: s2-p2@1ce {
+				reg = <0x1ce 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s3_p2: s3-p2@1cf {
+				reg = <0x1cf 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s4_p2: s4-p2@446 {
+				reg = <0x446 0x2>;
+				bits = <4 6>;
+			};
+
+			tsens_s5_p2: s5-p2@447 {
+				reg = <0x447 0x1>;
+				bits = <2 6>;
+			};
+
+			tsens_s6_p2: s6-p2@44e {
+				reg = <0x44e 0x1>;
+				bits = <1 6>;
+			};
+
+			tsens_mode: mode@44f {
+				reg = <0x44f 0x1>;
+				bits = <5 3>;
+			};
+		};
+
+		spmi_bus: spmi@fc4cf000 {
+			compatible = "qcom,spmi-pmic-arb";
+			reg-names = "core", "intr", "cnfg";
+			reg = <0xfc4cf000 0x1000>,
+			      <0xfc4cb000 0x1000>,
+			      <0xfc4ca000 0x1000>;
+			interrupt-names = "periph_irq";
+			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,ee = <0>;
+			qcom,channel = <0>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			interrupt-controller;
+			#interrupt-cells = <4>;
+		};
+
+		bam_dmux_dma: dma-controller@fc834000 {
+			compatible = "qcom,bam-v1.4.0";
+			reg = <0xfc834000 0x7000>;
+			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+
+			num-channels = <6>;
+			qcom,num-ees = <1>;
+			qcom,powered-remotely;
+		};
+
+		modem: remoteproc@fc880000 {
+			compatible = "qcom,msm8226-mss-pil";
+			reg = <0xfc880000 0x4040>,
+			      <0xfc820000 0x10000>;
+			reg-names = "qdsp6",
+				    "rmb";
+
+			interrupts-extended = <&intc GIC_SPI 24 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog",
+					  "fatal",
+					  "ready",
+					  "handover",
+					  "stop-ack";
+
+			clocks = <&gcc GCC_MSS_Q6_BIMC_AXI_CLK>,
+				 <&gcc GCC_MSS_CFG_AHB_CLK>,
+				 <&gcc GCC_BOOT_ROM_AHB_CLK>,
+				 <&rpmcc RPM_SMD_XO_CLK_SRC>;
+			clock-names = "iface",
+				      "bus",
+				      "mem",
+				      "xo";
+
+			resets = <&gcc GCC_MSS_RESTART>;
+			reset-names = "mss_restart";
+
+			power-domains = <&rpmpd MSM8226_VDDCX>;
+			power-domain-names = "cx";
+
+			qcom,ext-bhs-reg = <&tcsr_regs_1 0x194>;
+			qcom,halt-regs = <&tcsr_regs_1 0x180 0x200 0x280>;
+
+			qcom,smem-states = <&modem_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			memory-region = <&mba_region>, <&mpss_region>;
+
+			status = "disabled";
+
+			bam_dmux: bam-dmux {
+				compatible = "qcom,bam-dmux";
+
+				interrupt-parent = <&modem_smsm>;
+				interrupts = <1 IRQ_TYPE_EDGE_BOTH>, <11 IRQ_TYPE_EDGE_BOTH>;
+				interrupt-names = "pc", "pc-ack";
+
+				qcom,smem-states = <&apps_smsm 1>, <&apps_smsm 11>;
+				qcom,smem-state-names = "pc", "pc-ack";
+
+				dmas = <&bam_dmux_dma 4>, <&bam_dmux_dma 5>;
+				dma-names = "tx", "rx";
+			};
+
+			smd-edge {
+				interrupts = <GIC_SPI 25 IRQ_TYPE_EDGE_RISING>;
+
+				mboxes = <&apcs 12>;
+				qcom,smd-edge = <0>;
+
+				label = "modem";
+			};
+		};
+
+		tcsr_mutex: hwlock@fd484000 {
+			compatible = "qcom,msm8226-tcsr-mutex", "qcom,tcsr-mutex";
+			reg = <0xfd484000 0x1000>;
+			#hwlock-cells = <1>;
+		};
+
+		tcsr_regs_1: syscon@fd485000 {
+			compatible = "qcom,tcsr-msm8226", "syscon";
+			reg = <0xfd485000 0x1000>;
+		};
+
+		tlmm: pinctrl@fd510000 {
+			compatible = "qcom,msm8226-pinctrl";
+			reg = <0xfd510000 0x4000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&tlmm 0 0 117>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+
+			blsp1_i2c1_pins: blsp1-i2c1-state {
+				pins = "gpio2", "gpio3";
+				function = "blsp_i2c1";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_i2c2_pins: blsp1-i2c2-state {
+				pins = "gpio6", "gpio7";
+				function = "blsp_i2c2";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_i2c3_pins: blsp1-i2c3-state {
+				pins = "gpio10", "gpio11";
+				function = "blsp_i2c3";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_i2c4_pins: blsp1-i2c4-state {
+				pins = "gpio14", "gpio15";
+				function = "blsp_i2c4";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_i2c5_pins: blsp1-i2c5-state {
+				pins = "gpio18", "gpio19";
+				function = "blsp_i2c5";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_i2c6_pins: blsp1-i2c6-state {
+				pins = "gpio22", "gpio23";
+				function = "blsp_i2c6";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			cci_default: cci-default-state {
+				pins = "gpio29", "gpio30";
+				function = "cci_i2c0";
+
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			cci_sleep: cci-sleep-state {
+				pins = "gpio29", "gpio30";
+				function = "gpio";
+
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			sdhc1_default_state: sdhc1-default-state {
+				clk-pins {
+					pins = "sdc1_clk";
+					drive-strength = <10>;
+					bias-disable;
+				};
+
+				cmd-data-pins {
+					pins = "sdc1_cmd", "sdc1_data";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+			};
+
+			sdhc2_default_state: sdhc2-default-state {
+				clk-pins {
+					pins = "sdc2_clk";
+					drive-strength = <10>;
+					bias-disable;
+				};
+
+				cmd-data-pins {
+					pins = "sdc2_cmd", "sdc2_data";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+			};
+
+			sdhc3_default_state: sdhc3-default-state {
+				clk-pins {
+					pins = "gpio44";
+					function = "sdc3";
+					drive-strength = <8>;
+					bias-disable;
+				};
+
+				cmd-pins {
+					pins = "gpio43";
+					function = "sdc3";
+					drive-strength = <8>;
+					bias-pull-up;
+				};
+
+				data-pins {
+					pins = "gpio39", "gpio40", "gpio41", "gpio42";
+					function = "sdc3";
+					drive-strength = <8>;
+					bias-pull-up;
+				};
+			};
+		};
+
+		mmcc: clock-controller@fd8c0000 {
+			compatible = "qcom,mmcc-msm8226";
+			reg = <0xfd8c0000 0x6000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+
+			clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
+				 <&gcc GCC_MMSS_GPLL0_CLK_SRC>,
+				 <&gcc GPLL0_VOTE>,
+				 <&gcc GPLL1_VOTE>,
+				 <&rpmcc RPM_SMD_GFX3D_CLK_SRC>,
+				 <&mdss_dsi0_phy DSI_PIXEL_PLL_CLK>,
+				 <&mdss_dsi0_phy DSI_BYTE_PLL_CLK>;
+			clock-names = "xo",
+				      "mmss_gpll0_vote",
+				      "gpll0_vote",
+				      "gpll1_vote",
+				      "gfx3d_clk_src",
+				      "dsi0pll",
+				      "dsi0pllbyte";
+		};
+
+		mdss: display-subsystem@fd900000 {
+			compatible = "qcom,mdss";
+			reg = <0xfd900000 0x100>, <0xfd924000 0x1000>;
+			reg-names = "mdss_phys", "vbif_phys";
+
+			power-domains = <&mmcc MDSS_GDSC>;
+
+			clocks = <&mmcc MDSS_AHB_CLK>,
+				 <&mmcc MDSS_AXI_CLK>,
+				 <&mmcc MDSS_VSYNC_CLK>;
+			clock-names = "iface",
+				      "bus",
+				      "vsync";
+
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			status = "disabled";
+
+			mdss_mdp: display-controller@fd900000 {
+				compatible = "qcom,msm8226-mdp5", "qcom,mdp5";
+				reg = <0xfd900100 0x22000>;
+				reg-names = "mdp_phys";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <0>;
+
+				clocks = <&mmcc MDSS_AHB_CLK>,
+					 <&mmcc MDSS_AXI_CLK>,
+					 <&mmcc MDSS_MDP_CLK>,
+					 <&mmcc MDSS_VSYNC_CLK>;
+				clock-names = "iface",
+					      "bus",
+					      "core",
+					      "vsync";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						mdss_mdp_intf1_out: endpoint {
+							remote-endpoint = <&mdss_dsi0_in>;
+						};
+					};
+				};
+			};
+
+			mdss_dsi0: dsi@fd922800 {
+				compatible = "qcom,msm8226-dsi-ctrl",
+					     "qcom,mdss-dsi-ctrl";
+				reg = <0xfd922800 0x1f8>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <4>;
+
+				assigned-clocks = <&mmcc BYTE0_CLK_SRC>,
+						  <&mmcc PCLK0_CLK_SRC>;
+				assigned-clock-parents = <&mdss_dsi0_phy DSI_BYTE_PLL_CLK>,
+							 <&mdss_dsi0_phy DSI_PIXEL_PLL_CLK>;
+
+				clocks = <&mmcc MDSS_MDP_CLK>,
+					 <&mmcc MDSS_AHB_CLK>,
+					 <&mmcc MDSS_AXI_CLK>,
+					 <&mmcc MDSS_BYTE0_CLK>,
+					 <&mmcc MDSS_PCLK0_CLK>,
+					 <&mmcc MDSS_ESC0_CLK>,
+					 <&mmcc MMSS_MISC_AHB_CLK>;
+				clock-names = "mdp_core",
+					      "iface",
+					      "bus",
+					      "byte",
+					      "pixel",
+					      "core",
+					      "core_mmss";
+
+				phys = <&mdss_dsi0_phy>;
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						mdss_dsi0_in: endpoint {
+							remote-endpoint = <&mdss_mdp_intf1_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						mdss_dsi0_out: endpoint {
+						};
+					};
+				};
+			};
+
+			mdss_dsi0_phy: phy@fd922a00 {
+				compatible = "qcom,dsi-phy-28nm-8226";
+				reg = <0xfd922a00 0xd4>,
+				      <0xfd922b00 0x280>,
+				      <0xfd922d80 0x30>;
+				reg-names = "dsi_pll",
+					    "dsi_phy",
+					    "dsi_phy_regulator";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				clocks = <&mmcc MDSS_AHB_CLK>,
+					 <&rpmcc RPM_SMD_XO_CLK_SRC>;
+				clock-names = "iface",
+					      "ref";
+			};
+		};
+
+		cci: cci@fda0c000 {
+			compatible = "qcom,msm8226-cci";
+			reg = <0xfda0c000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&mmcc CAMSS_TOP_AHB_CLK>,
+				 <&mmcc CAMSS_CCI_CCI_AHB_CLK>,
+				 <&mmcc CAMSS_CCI_CCI_CLK>;
+			clock-names = "camss_top_ahb",
+				      "cci_ahb",
+				      "cci";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&cci_default>;
+			pinctrl-1 = <&cci_sleep>;
+
+			status = "disabled";
+
+			cci_i2c0: i2c-bus@0 {
+				reg = <0>;
+				clock-frequency = <400000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		gpu: gpu@fdb00000 {
+			compatible = "qcom,adreno-305.18", "qcom,adreno";
+			reg = <0xfdb00000 0x10000>;
+			reg-names = "kgsl_3d0_reg_memory";
+
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "kgsl_3d0_irq";
+
+			clocks = <&mmcc OXILI_GFX3D_CLK>,
+				 <&mmcc OXILICX_AHB_CLK>,
+				 <&mmcc OXILICX_AXI_CLK>;
+			clock-names = "core", "iface", "mem_iface";
+
+			sram = <&gmu_sram>;
+			power-domains = <&mmcc OXILICX_GDSC>;
+			operating-points-v2 = <&gpu_opp_table>;
+
+			status = "disabled";
+
+			gpu_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-450000000 {
+					opp-hz = /bits/ 64 <450000000>;
+				};
+
+				opp-320000000 {
+					opp-hz = /bits/ 64 <320000000>;
+				};
+
+				opp-200000000 {
+					opp-hz = /bits/ 64 <200000000>;
+				};
+
+				opp-19000000 {
+					opp-hz = /bits/ 64 <19000000>;
+				};
+			};
+		};
+
+		sram@fdd00000 {
+			compatible = "qcom,msm8226-ocmem";
+			reg = <0xfdd00000 0x2000>,
+			      <0xfec00000 0x20000>;
+			reg-names = "ctrl", "mem";
+			ranges = <0 0xfec00000 0x20000>;
+			clocks = <&rpmcc RPM_SMD_OCMEMGX_CLK>;
+			clock-names = "core";
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			gmu_sram: gmu-sram@0 {
+				reg = <0x0 0x20000>;
+			};
+		};
+
+		adsp: remoteproc@fe200000 {
+			compatible = "qcom,msm8226-adsp-pil";
+			reg = <0xfe200000 0x100>;
+
+			interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_EDGE_RISING>,
+					      <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
+
+			power-domains = <&rpmpd MSM8226_VDDCX>;
+			power-domain-names = "cx";
+
+			clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>;
+			clock-names = "xo";
+
+			memory-region = <&adsp_region>;
+
+			qcom,smem-states = <&adsp_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			smd-edge {
+				interrupts = <GIC_SPI 156 IRQ_TYPE_EDGE_RISING>;
+
+				mboxes = <&apcs 8>;
+				qcom,smd-edge = <1>;
+
+				label = "lpass";
+			};
+		};
+
+		sram@fe805000 {
+			compatible = "qcom,msm8226-imem", "syscon", "simple-mfd";
+			reg = <0xfe805000 0x1000>;
+
+			reboot-mode {
+				compatible = "syscon-reboot-mode";
+				offset = <0x65c>;
+
+				mode-bootloader = <0x77665500>;
+				mode-normal = <0x77665501>;
+				mode-recovery = <0x77665502>;
+			};
+		};
+	};
+
+	thermal-zones {
+		cpu0-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 5>;
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert0>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+
+			trips {
+				cpu_alert0: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_crit0: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu1-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 2>;
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert1>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+
+			trips {
+				cpu_alert1: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_crit1: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 2
+				(GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 3
+				(GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 4
+				(GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 1
+				(GIC_CPU_MASK_RAW(15) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts b/arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts
new file mode 100644
index 000000000000..69fe651f564d
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8660-surf.dts
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/input/input.h>
+
+#include "qcom-msm8660.dtsi"
+#include "pm8058.dtsi"
+
+/ {
+	model = "Qualcomm MSM8660 SURF";
+	compatible = "qcom,msm8660-surf", "qcom,msm8660";
+
+	aliases {
+		serial0 = &gsbi12_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	/* Temporary fixed regulator */
+	vsdcc_fixed: vsdcc-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "SDCC Power";
+		regulator-min-microvolt = <2700000>;
+		regulator-max-microvolt = <2700000>;
+		regulator-always-on;
+	};
+};
+
+&gsbi12 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi12_serial {
+	status = "okay";
+};
+
+&pm8058 {
+	interrupts-extended = <&tlmm 88 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&pm8058_keypad {
+	linux,keymap = <
+		MATRIX_KEY(0, 0, KEY_FN_F1)
+		MATRIX_KEY(0, 1, KEY_UP)
+		MATRIX_KEY(0, 2, KEY_LEFT)
+		MATRIX_KEY(0, 3, KEY_VOLUMEUP)
+		MATRIX_KEY(1, 0, KEY_FN_F2)
+		MATRIX_KEY(1, 1, KEY_RIGHT)
+		MATRIX_KEY(1, 2, KEY_DOWN)
+		MATRIX_KEY(1, 3, KEY_VOLUMEDOWN)
+		MATRIX_KEY(2, 3, KEY_ENTER)
+		MATRIX_KEY(4, 0, KEY_CAMERA_FOCUS)
+		MATRIX_KEY(4, 1, KEY_UP)
+		MATRIX_KEY(4, 2, KEY_LEFT)
+		MATRIX_KEY(4, 3, KEY_HOME)
+		MATRIX_KEY(4, 4, KEY_FN_F3)
+		MATRIX_KEY(5, 0, KEY_CAMERA)
+		MATRIX_KEY(5, 1, KEY_RIGHT)
+		MATRIX_KEY(5, 2, KEY_DOWN)
+		MATRIX_KEY(5, 3, KEY_BACK)
+		MATRIX_KEY(5, 4, KEY_MENU)
+		>;
+	keypad,num-rows = <6>;
+	keypad,num-columns = <5>;
+};
+
+&rpm {
+	regulators-0 {
+		compatible = "qcom,rpm-pm8901-regulators";
+	};
+
+	regulators-1 {
+		compatible = "qcom,rpm-pm8058-regulators";
+	};
+};
+
+/* eMMC */
+&sdcc1 {
+	vmmc-supply = <&vsdcc_fixed>;
+	status = "okay";
+};
+
+/* External micro SD card */
+&sdcc3 {
+	vmmc-supply = <&vsdcc_fixed>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8660.dtsi
index a258abb23a64..3f69b98d0041 100644
--- a/arch/arm/boot/dts/qcom-msm8660.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-msm8660.dtsi
@@ -22,7 +22,7 @@
 			enable-method = "qcom,gcc-msm8660";
 			device_type = "cpu";
 			reg = <0>;
-			next-level-cache = <&L2>;
+			next-level-cache = <&l2>;
 		};
 
 		cpu@1 {
@@ -30,12 +30,13 @@
 			enable-method = "qcom,gcc-msm8660";
 			device_type = "cpu";
 			reg = <1>;
-			next-level-cache = <&L2>;
+			next-level-cache = <&l2>;
 		};
 
-		L2: l2-cache {
+		l2: l2-cache {
 			compatible = "cache";
 			cache-level = <2>;
+			cache-unified;
 		};
 	};
 
@@ -46,45 +47,32 @@
 
 	cpu-pmu {
 		compatible = "qcom,scorpion-mp-pmu";
-		interrupts = <1 9 0x304>;
+		interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
 	};
 
 	clocks {
-		cxo_board {
+		cxo_board: cxo-board-clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <19200000>;
+			clock-output-names = "cxo_board";
 		};
 
-		pxo_board {
+		pxo_board: pxo-board-clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <27000000>;
+			clock-output-names = "pxo_board";
 		};
 
-		sleep_clk {
+		sleep-clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <32768>;
+			clock-output-names = "sleep_clk";
 		};
 	};
 
-	/*
-	 * These channels from the ADC are simply hardware monitors.
-	 * That is why the ADC is referred to as "HKADC" - HouseKeeping
-	 * ADC.
-	 */
-	iio-hwmon {
-		compatible = "iio-hwmon";
-		io-channels = <&xoadc 0x00 0x01>, /* Battery */
-			    <&xoadc 0x00 0x02>, /* DC in (charger) */
-			    <&xoadc 0x00 0x04>, /* VPH the main system voltage */
-			    <&xoadc 0x00 0x0b>, /* Die temperature */
-			    <&xoadc 0x00 0x0c>, /* Reference voltage 1.25V */
-			    <&xoadc 0x00 0x0d>, /* Reference voltage 0.625V */
-			    <&xoadc 0x00 0x0e>; /* Reference voltage 0.325V */
-	};
-
 	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -101,12 +89,11 @@
 
 		timer@2000000 {
 			compatible = "qcom,scss-timer", "qcom,msm-timer";
-			interrupts = <1 0 0x301>,
-				     <1 1 0x301>,
-				     <1 2 0x301>;
+			interrupts = <GIC_PPI 0 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_EDGE_RISING)>,
+				     <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_EDGE_RISING)>,
+				     <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_EDGE_RISING)>;
 			reg = <0x02000000 0x100>;
-			clock-frequency = <27000000>,
-					  <32768>;
+			clock-frequency = <27000000>;
 			cpu-offset = <0x40000>;
 		};
 
@@ -117,7 +104,7 @@
 			gpio-controller;
 			gpio-ranges = <&tlmm 0 0 173>;
 			#gpio-cells = <2>;
-			interrupts = <0 16 0x4>;
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
 
@@ -126,9 +113,61 @@
 		gcc: clock-controller@900000 {
 			compatible = "qcom,gcc-msm8660";
 			#clock-cells = <1>;
-			#power-domain-cells = <1>;
 			#reset-cells = <1>;
 			reg = <0x900000 0x4000>;
+			clocks = <&pxo_board>, <&cxo_board>;
+			clock-names = "pxo", "cxo";
+		};
+
+		gsbi1: gsbi@16000000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <12>;
+			reg = <0x16000000 0x100>;
+			clocks = <&gcc GSBI1_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+
+			status = "disabled";
+
+			gsbi1_spi: spi@16080000 {
+				compatible = "qcom,spi-qup-v1.1.1";
+				reg = <0x16080000 0x1000>;
+				interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>;
+				clock-names = "core", "iface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		gsbi3: gsbi@16200000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <12>;
+			reg = <0x16200000 0x100>;
+			clocks = <&gcc GSBI3_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+			status = "disabled";
+
+			gsbi3_i2c: i2c@16280000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x16280000 0x1000>;
+				interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI3_QUP_CLK>, <&gcc GSBI3_H_CLK>;
+				clock-names = "core", "iface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
 		};
 
 		gsbi6: gsbi@16500000 {
@@ -212,6 +251,7 @@
 			ranges;
 
 			syscon-tcsr = <&tcsr>;
+			status = "disabled";
 
 			gsbi8_i2c: i2c@19880000 {
 				compatible = "qcom,i2c-qup-v1.1.1";
@@ -241,7 +281,7 @@
 				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
 				reg = <0x19c40000 0x1000>,
 				      <0x19c00000 0x1000>;
-				interrupts = <0 195 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&gcc GSBI12_UART_CLK>, <&gcc GSBI12_H_CLK>;
 				clock-names = "core", "iface";
 				status = "disabled";
@@ -250,7 +290,7 @@
 			gsbi12_i2c: i2c@19c80000 {
 				compatible = "qcom,i2c-qup-v1.1.1";
 				reg = <0x19c80000 0x1000>;
-				interrupts = <0 196 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&gcc GSBI12_QUP_CLK>, <&gcc GSBI12_H_CLK>;
 				clock-names = "core", "iface";
 				#address-cells = <1>;
@@ -259,7 +299,7 @@
 			};
 		};
 
-		external-bus@1a100000 {
+		ebi2: external-bus@1a100000 {
 			compatible = "qcom,msm8660-ebi2";
 			#address-cells = <2>;
 			#size-cells = <1>;
@@ -276,206 +316,34 @@
 			status = "disabled";
 		};
 
-		qcom,ssbi@500000 {
+		ssbi: ssbi@500000 {
 			compatible = "qcom,ssbi";
 			reg = <0x500000 0x1000>;
 			qcom,controller-type = "pmic-arbiter";
-
-			pm8058: pmic@0 {
-				compatible = "qcom,pm8058";
-				interrupt-parent = <&tlmm>;
-				interrupts = <88 8>;
-				#interrupt-cells = <2>;
-				interrupt-controller;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				pm8058_gpio: gpio@150 {
-					compatible = "qcom,pm8058-gpio",
-						     "qcom,ssbi-gpio";
-					reg = <0x150>;
-					interrupt-controller;
-					#interrupt-cells = <2>;
-					gpio-controller;
-					gpio-ranges = <&pm8058_gpio 0 0 44>;
-					#gpio-cells = <2>;
-
-				};
-
-				pm8058_mpps: mpps@50 {
-					compatible = "qcom,pm8058-mpp",
-						     "qcom,ssbi-mpp";
-					reg = <0x50>;
-					gpio-controller;
-					#gpio-cells = <2>;
-					gpio-ranges = <&pm8058_mpps 0 0 12>;
-					interrupt-controller;
-					#interrupt-cells = <2>;
-				};
-
-				pwrkey@1c {
-					compatible = "qcom,pm8058-pwrkey";
-					reg = <0x1c>;
-					interrupt-parent = <&pm8058>;
-					interrupts = <50 1>, <51 1>;
-					debounce = <15625>;
-					pull-up;
-				};
-
-				keypad@148 {
-					compatible = "qcom,pm8058-keypad";
-					reg = <0x148>;
-					interrupt-parent = <&pm8058>;
-					interrupts = <74 1>, <75 1>;
-					debounce = <15>;
-					scan-delay = <32>;
-					row-hold = <91500>;
-				};
-
-				xoadc: xoadc@197 {
-					compatible = "qcom,pm8058-adc";
-					reg = <0x197>;
-					interrupts-extended = <&pm8058 76 IRQ_TYPE_EDGE_RISING>;
-					#address-cells = <2>;
-					#size-cells = <0>;
-					#io-channel-cells = <2>;
-
-					vcoin: adc-channel@0 {
-						reg = <0x00 0x00>;
-					};
-					vbat: adc-channel@1 {
-						reg = <0x00 0x01>;
-					};
-					dcin: adc-channel@2 {
-						reg = <0x00 0x02>;
-					};
-					ichg: adc-channel@3 {
-						reg = <0x00 0x03>;
-					};
-					vph_pwr: adc-channel@4 {
-						reg = <0x00 0x04>;
-					};
-					usb_vbus: adc-channel@a {
-						reg = <0x00 0x0a>;
-					};
-					die_temp: adc-channel@b {
-						reg = <0x00 0x0b>;
-					};
-					ref_625mv: adc-channel@c {
-						reg = <0x00 0x0c>;
-					};
-					ref_1250mv: adc-channel@d {
-						reg = <0x00 0x0d>;
-					};
-					ref_325mv: adc-channel@e {
-						reg = <0x00 0x0e>;
-					};
-					ref_muxoff: adc-channel@f {
-						reg = <0x00 0x0f>;
-					};
-				};
-
-				rtc@1e8 {
-					compatible = "qcom,pm8058-rtc";
-					reg = <0x1e8>;
-					interrupt-parent = <&pm8058>;
-					interrupts = <39 1>;
-					allow-set-time;
-				};
-
-				vibrator@4a {
-					compatible = "qcom,pm8058-vib";
-					reg = <0x4a>;
-				};
-			};
 		};
 
 		l2cc: clock-controller@2082000 {
-			compatible	= "qcom,kpss-gcc", "syscon";
-			reg		= <0x02082000 0x1000>;
+			compatible = "qcom,kpss-gcc-msm8660", "qcom,kpss-gcc", "syscon";
+			reg = <0x02082000 0x1000>;
 		};
 
 		rpm: rpm@104000 {
-			compatible	= "qcom,rpm-msm8660";
-			reg		= <0x00104000 0x1000>;
-			qcom,ipc	= <&l2cc 0x8 2>;
-
-			interrupts	= <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
-					  <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
-					  <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
-			interrupt-names	= "ack", "err", "wakeup";
+			compatible = "qcom,rpm-msm8660";
+			reg = <0x00104000 0x1000>;
+			qcom,ipc = <&l2cc 0x8 2>;
+
+			interrupts = <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "ack", "err", "wakeup";
 			clocks = <&gcc RPM_MSG_RAM_H_CLK>;
 			clock-names = "ram";
 
 			rpmcc: clock-controller {
-				compatible	= "qcom,rpmcc-msm8660", "qcom,rpmcc";
+				compatible = "qcom,rpmcc-msm8660", "qcom,rpmcc";
 				#clock-cells = <1>;
-			};
-
-			pm8901-regulators {
-				compatible = "qcom,rpm-pm8901-regulators";
-
-				pm8901_l0: l0 {};
-				pm8901_l1: l1 {};
-				pm8901_l2: l2 {};
-				pm8901_l3: l3 {};
-				pm8901_l4: l4 {};
-				pm8901_l5: l5 {};
-				pm8901_l6: l6 {};
-
-				/* S0 and S1 Handled as SAW regulators by SPM */
-				pm8901_s2: s2 {};
-				pm8901_s3: s3 {};
-				pm8901_s4: s4 {};
-
-				pm8901_lvs0: lvs0 {};
-				pm8901_lvs1: lvs1 {};
-				pm8901_lvs2: lvs2 {};
-				pm8901_lvs3: lvs3 {};
-
-				pm8901_mvs: mvs {};
-			};
-
-			pm8058-regulators {
-				compatible = "qcom,rpm-pm8058-regulators";
-
-				pm8058_l0: l0 {};
-				pm8058_l1: l1 {};
-				pm8058_l2: l2 {};
-				pm8058_l3: l3 {};
-				pm8058_l4: l4 {};
-				pm8058_l5: l5 {};
-				pm8058_l6: l6 {};
-				pm8058_l7: l7 {};
-				pm8058_l8: l8 {};
-				pm8058_l9: l9 {};
-				pm8058_l10: l10 {};
-				pm8058_l11: l11 {};
-				pm8058_l12: l12 {};
-				pm8058_l13: l13 {};
-				pm8058_l14: l14 {};
-				pm8058_l15: l15 {};
-				pm8058_l16: l16 {};
-				pm8058_l17: l17 {};
-				pm8058_l18: l18 {};
-				pm8058_l19: l19 {};
-				pm8058_l20: l20 {};
-				pm8058_l21: l21 {};
-				pm8058_l22: l22 {};
-				pm8058_l23: l23 {};
-				pm8058_l24: l24 {};
-				pm8058_l25: l25 {};
-
-				pm8058_s0: s0 {};
-				pm8058_s1: s1 {};
-				pm8058_s2: s2 {};
-				pm8058_s3: s3 {};
-				pm8058_s4: s4 {};
-
-				pm8058_lvs0: lvs0 {};
-				pm8058_lvs1: lvs1 {};
-
-				pm8058_ncp: ncp {};
+				clocks = <&pxo_board>;
+				clock-names = "pxo";
 			};
 		};
 
@@ -485,80 +353,75 @@
 			#size-cells = <1>;
 			ranges;
 			sdcc1: mmc@12400000 {
-				status		= "disabled";
-				compatible	= "arm,pl18x", "arm,primecell";
+				status = "disabled";
+				compatible = "arm,pl18x", "arm,primecell";
 				arm,primecell-periphid = <0x00051180>;
-				reg		= <0x12400000 0x8000>;
-				interrupts	= <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <8>;
-				max-frequency	= <48000000>;
+				reg = <0x12400000 0x8000>;
+				interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <8>;
+				max-frequency = <48000000>;
 				non-removable;
 				cap-sd-highspeed;
 				cap-mmc-highspeed;
 			};
 
 			sdcc2: mmc@12140000 {
-				status		= "disabled";
-				compatible	= "arm,pl18x", "arm,primecell";
+				status = "disabled";
+				compatible = "arm,pl18x", "arm,primecell";
 				arm,primecell-periphid = <0x00051180>;
-				reg		= <0x12140000 0x8000>;
-				interrupts	= <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC2_CLK>, <&gcc SDC2_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <8>;
-				max-frequency	= <48000000>;
+				reg = <0x12140000 0x8000>;
+				interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc SDC2_CLK>, <&gcc SDC2_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <8>;
+				max-frequency = <48000000>;
 				cap-sd-highspeed;
 				cap-mmc-highspeed;
 			};
 
 			sdcc3: mmc@12180000 {
-				compatible	= "arm,pl18x", "arm,primecell";
+				compatible = "arm,pl18x", "arm,primecell";
 				arm,primecell-periphid = <0x00051180>;
-				status		= "disabled";
-				reg		= <0x12180000 0x8000>;
-				interrupts	= <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <4>;
+				status = "disabled";
+				reg = <0x12180000 0x8000>;
+				interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <4>;
 				cap-sd-highspeed;
 				cap-mmc-highspeed;
-				max-frequency	= <48000000>;
+				max-frequency = <48000000>;
 				no-1-8-v;
 			};
 
 			sdcc4: mmc@121c0000 {
-				compatible	= "arm,pl18x", "arm,primecell";
+				compatible = "arm,pl18x", "arm,primecell";
 				arm,primecell-periphid = <0x00051180>;
-				status		= "disabled";
-				reg		= <0x121c0000 0x8000>;
-				interrupts	= <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC4_CLK>, <&gcc SDC4_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <4>;
-				max-frequency	= <48000000>;
+				status = "disabled";
+				reg = <0x121c0000 0x8000>;
+				interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc SDC4_CLK>, <&gcc SDC4_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <4>;
+				max-frequency = <48000000>;
 				cap-sd-highspeed;
 				cap-mmc-highspeed;
 			};
 
 			sdcc5: mmc@12200000 {
-				compatible	= "arm,pl18x", "arm,primecell";
+				compatible = "arm,pl18x", "arm,primecell";
 				arm,primecell-periphid = <0x00051180>;
-				status		= "disabled";
-				reg		= <0x12200000 0x8000>;
-				interrupts	= <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC5_CLK>, <&gcc SDC5_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <4>;
+				status = "disabled";
+				reg = <0x12200000 0x8000>;
+				interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc SDC5_CLK>, <&gcc SDC5_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <4>;
 				cap-sd-highspeed;
 				cap-mmc-highspeed;
-				max-frequency	= <48000000>;
+				max-frequency = <48000000>;
 			};
 		};
 
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-e5.dts b/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-e5.dts
new file mode 100644
index 000000000000..c8d34de8a71e
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-e5.dts
@@ -0,0 +1,3 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include "arm64/qcom/msm8916-samsung-e5.dts"
+#include "qcom-msm8916-smp.dtsi"
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-e7.dts b/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-e7.dts
new file mode 100644
index 000000000000..85be286c8608
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-e7.dts
@@ -0,0 +1,3 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include "arm64/qcom/msm8916-samsung-e7.dts"
+#include "qcom-msm8916-smp.dtsi"
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-grandmax.dts b/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-grandmax.dts
new file mode 100644
index 000000000000..d3abe0536238
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-grandmax.dts
@@ -0,0 +1,3 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include "arm64/qcom/msm8916-samsung-grandmax.dts"
+#include "qcom-msm8916-smp.dtsi"
diff --git a/arch/arm/boot/dts/qcom-msm8916-samsung-serranove.dts b/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-serranove.dts
index dee2c20af355..dee2c20af355 100644
--- a/arch/arm/boot/dts/qcom-msm8916-samsung-serranove.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8916-samsung-serranove.dts
diff --git a/arch/arm/boot/dts/qcom-msm8916-smp.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8916-smp.dtsi
index 36328dbe4212..94b7694eeeff 100644
--- a/arch/arm/boot/dts/qcom-msm8916-smp.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-msm8916-smp.dtsi
@@ -25,8 +25,8 @@
 	};
 };
 
-&CPU_SLEEP_0 {
-	compatible = "qcom,idle-state-spc";
+&cpu_sleep_0 {
+	compatible = "qcom,idle-state-spc", "arm,idle-state";
 };
 
 &cpu0_acc {
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8926-htc-memul.dts b/arch/arm/boot/dts/qcom/qcom-msm8926-htc-memul.dts
new file mode 100644
index 000000000000..cb571aa13c11
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8926-htc-memul.dts
@@ -0,0 +1,397 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023, Luca Weiss <luca@z3ntu.xyz>
+ */
+
+/dts-v1/;
+
+#include "msm8926.dtsi"
+#include "pm8226.dtsi"
+
+/delete-node/ &adsp_region;
+/delete-node/ &mba_region;
+/delete-node/ &mpss_region;
+/delete-node/ &smem_region;
+
+/ {
+	model = "HTC One Mini 2";
+	compatible = "htc,memul", "qcom,msm8926", "qcom,msm8226";
+	chassis-type = "handset";
+
+	aliases {
+		mmc1 = &sdhc_2; /* SDC2 SD card slot */
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-power {
+			label = "Power";
+			gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			debounce-interval = <15>;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <15>;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&tlmm 108 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <15>;
+		};
+	};
+
+	reserved-memory {
+		unknown@5b00000 {
+			reg = <0x05b00000 0x200000>;
+			no-map;
+		};
+
+		unknown@7500000 {
+			reg = <0x07500000 0xb00000>;
+			no-map;
+		};
+
+		mpss_region: mpss@8000000 {
+			reg = <0x08000000 0x4f00000>;
+			no-map;
+		};
+
+		unknown@cf00000 {
+			reg = <0x0cf00000 0x200000>;
+			no-map;
+		};
+
+		mba_region: mba@d100000 {
+			reg = <0x0d100000 0x3a000>;
+			no-map;
+		};
+
+		unknown@d13a000 {
+			reg = <0x0d13a000 0xc6000>;
+			no-map;
+		};
+
+		wcnss_region: wcnss@d200000 {
+			reg = <0x0d200000 0x650000>;
+			no-map;
+		};
+
+		unknown@d850000 {
+			reg = <0x0d850000 0x3b0000>;
+			no-map;
+		};
+
+		adsp_region: adsp@dc00000 {
+			reg = <0x0dc00000 0x1400000>;
+			no-map;
+		};
+
+		unknown@f000000 {
+			reg = <0x0f000000 0x500000>;
+			no-map;
+		};
+
+		venus_region: venus@f500000 {
+			reg = <0x0f500000 0x500000>;
+			no-map;
+		};
+
+		smem_region: smem@fa00000 {
+			reg = <0x0fa00000 0x100000>;
+			no-map;
+		};
+
+		unknown@fb00000 {
+			reg = <0x0fb00000 0x280000>;
+			no-map;
+		};
+
+		rmtfs@fd80000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0x0fd80000 0x180000>;
+			no-map;
+
+			qcom,client-id = <1>;
+		};
+
+		unknown@ff00000 {
+			reg = <0x0ff00000 0x1700000>;
+			no-map;
+		};
+	};
+};
+
+&adsp {
+	firmware-name = "qcom/msm8926/memul/adsp.mbn";
+	status = "okay";
+};
+
+&blsp1_i2c2 {
+	status = "okay";
+
+	magnetometer@d {
+		compatible = "asahi-kasei,ak8963";
+		reg = <0x0d>;
+		interrupts-extended = <&tlmm 66 IRQ_TYPE_EDGE_RISING>;
+		vdd-supply = <&pm8226_l19>;
+		vid-supply = <&pm8226_l28>;
+	};
+
+	accelerometer@18 {
+		compatible = "bosch,bma250e";
+		reg = <0x18>;
+		interrupts-extended = <&tlmm 63 IRQ_TYPE_EDGE_RISING>;
+		vdd-supply = <&pm8226_l19>;
+		vddio-supply = <&pm8226_l28>;
+	};
+};
+
+&blsp1_i2c4 {
+	status = "okay";
+
+	/* TFA9887 @ 34 */
+	/* TFA9887 @ 35 */
+};
+
+&blsp1_i2c5 {
+	status = "okay";
+
+	touchscreen@20 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x20>;
+
+		interrupts-extended = <&tlmm 17 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8226_l19>;
+
+		syna,startup-delay-ms = <160>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmi4-f01@1 {
+			reg = <0x1>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp1_i2c6 {
+	status = "okay";
+
+	/* NCP6924 Camera Regulators @ 10 */
+	/* PN544 NFC @ 28 */
+	/* TPS61310 Flash/Torch @ 33 */
+};
+
+&modem {
+	mx-supply = <&pm8226_l3>;
+	pll-supply = <&pm8226_l8>;
+	mss-supply = <&pm8226_s5>;
+
+	firmware-name = "qcom/msm8926/memul/mba.b00", "qcom/msm8926/memul/modem.mdt";
+
+	status = "okay";
+};
+
+&pm8226_vib {
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-pm8226-regulators";
+
+		pm8226_s3: s3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8226_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2200000>;
+		};
+
+		pm8226_s5: s5 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8226_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l3: l3 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1337500>;
+		};
+
+		pm8226_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l5: l5 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l7: l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <1850000>;
+		};
+
+		pm8226_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l9: l9 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l14: l14 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+		};
+
+		pm8226_l15: l15 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8226_l16: l16 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3350000>;
+		};
+
+		pm8226_l17: l17 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l18: l18 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l19: l19 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8226_l20: l20 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+
+		pm8226_l21: l21 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-allow-set-load;
+		};
+
+		pm8226_l22: l22 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8226_l24: l24 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8226_l25: l25 {
+			regulator-min-microvolt = <1775000>;
+			regulator-max-microvolt = <2125000>;
+		};
+
+		pm8226_l26: l26 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8226_l27: l27 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l28: l28 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_lvs1: lvs1 {};
+	};
+};
+
+&sdhc_2 {
+	vmmc-supply = <&pm8226_l18>;
+	vqmmc-supply = <&pm8226_l21>;
+
+	bus-width = <4>;
+	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+
+	status = "okay";
+};
+
+&smbb {
+	qcom,fast-charge-safe-current = <1750000>;
+	qcom,fast-charge-current-limit = <1750000>;
+	qcom,fast-charge-safe-voltage = <4360000>;
+	qcom,fast-charge-high-threshold-voltage = <4350000>;
+	qcom,auto-recharge-threshold-voltage = <4300000>;
+	qcom,minimum-input-voltage = <4300000>;
+
+	status = "okay";
+};
+
+&usb {
+	extcon = <&smbb>;
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usb_hs_phy {
+	extcon = <&smbb>;
+	v1p8-supply = <&pm8226_l10>;
+	v3p3-supply = <&pm8226_l20>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8926-microsoft-superman-lte.dts b/arch/arm/boot/dts/qcom/qcom-msm8926-microsoft-superman-lte.dts
new file mode 100644
index 000000000000..eea4fd8cd972
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8926-microsoft-superman-lte.dts
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023, Jack Matthews <jm5112356@gmail.com>
+ * Copyright (c) 2023, Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
+ * Copyright (c) 2023, Dominik Kobinski <dominikkobinski314@gmail.com>
+ * Copyright (c) 2023, Rayyan Ansari <rayyan@ansari.sh>
+ */
+
+/dts-v1/;
+
+#include "msm8926.dtsi"
+#include "qcom-msm8226-microsoft-common.dtsi"
+
+/* This device has touchscreen on i2c3 instead */
+/delete-node/ &touchscreen;
+
+/ {
+	model = "Nokia Lumia 735";
+	compatible = "microsoft,superman-lte", "qcom,msm8926", "qcom,msm8226";
+	chassis-type = "handset";
+};
+
+&blsp1_i2c3 {
+	status = "okay";
+
+	touchscreen: touchscreen@4b {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x4b>;
+
+		interrupts-extended = <&tlmm 17 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8226_l15>;
+		vio-supply = <&pm8226_l6>;
+
+		pinctrl-0 = <&touchscreen_default>;
+		pinctrl-names = "default";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmi4-f01@1 {
+			reg = <0x01>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f11@11 {
+			reg = <0x11>;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp1_i2c5 {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8926-microsoft-tesla.dts b/arch/arm/boot/dts/qcom/qcom-msm8926-microsoft-tesla.dts
new file mode 100644
index 000000000000..f23bbb94cc5e
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8926-microsoft-tesla.dts
@@ -0,0 +1,71 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023, Jack Matthews <jm5112356@gmail.com>
+ * Copyright (c) 2023, Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
+ * Copyright (c) 2023, Dominik Kobinski <dominikkobinski314@gmail.com>
+ * Copyright (c) 2023, Rayyan Ansari <rayyan@ansari.sh>
+ */
+
+/dts-v1/;
+
+#include "msm8926.dtsi"
+#include "qcom-msm8226-microsoft-common.dtsi"
+
+/* This device has touchscreen on i2c1 instead */
+/delete-node/ &touchscreen;
+
+/* The magnetometer used on this device is currently unknown */
+/delete-node/ &magnetometer;
+
+/ {
+	model = "Nokia Lumia 830";
+	compatible = "microsoft,tesla", "qcom,msm8926", "qcom,msm8226";
+	chassis-type = "handset";
+};
+
+&blsp1_i2c1 {
+	status = "okay";
+
+	touchscreen: touchscreen@4b {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x4b>;
+
+		interrupts-extended = <&tlmm 17 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8226_l15>;
+		vio-supply = <&pm8226_l6>;
+
+		pinctrl-0 = <&touchscreen_default>;
+		pinctrl-names = "default";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmi4-f01@1 {
+			reg = <0x01>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp1_i2c5 {
+	status = "disabled";
+};
+
+&gpio_keys {
+	key-camera-snapshot {
+		label = "Camera Snapshot";
+		gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
+		linux,code = <KEY_CAMERA>;
+	};
+
+	key-camera-focus {
+		label = "Camera Focus";
+		gpios = <&tlmm 108 GPIO_ACTIVE_LOW>;
+		linux,code = <KEY_CAMERA_FOCUS>;
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts b/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts
new file mode 100644
index 000000000000..db3273c755c2
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts
@@ -0,0 +1,412 @@
+// SPDX-License-Identifier: BSD-3-Clause
+
+/dts-v1/;
+
+#include "msm8926.dtsi"
+#include "pm8226.dtsi"
+
+/delete-node/ &smem_region;
+
+/ {
+	model = "Motorola Moto G 4G (2013)";
+	compatible = "motorola,peregrine", "qcom,msm8926", "qcom,msm8226";
+	chassis-type = "handset";
+
+	aliases {
+		mmc0 = &sdhc_1; /* SDC1 eMMC slot */
+		mmc1 = &sdhc_2; /* SDC2 SD card slot */
+	};
+
+	chosen {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		framebuffer0: framebuffer@3200000 {
+			compatible = "simple-framebuffer";
+			reg = <0x03200000 0x800000>;
+			width = <720>;
+			height = <1280>;
+			stride = <(720 * 3)>;
+			format = "r8g8b8";
+			vsp-supply = <&reg_lcd_pos>;
+			vsn-supply = <&reg_lcd_neg>;
+			vdd-supply = <&pm8226_l28>;
+			vddio-supply = <&vddio_disp_vreg>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		event-hall-sensor {
+			label = "Hall Effect Sensor";
+			gpios = <&tlmm 51 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			linux,can-disable;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <15>;
+		};
+	};
+
+	vddio_disp_vreg: regulator-vddio-disp {
+		compatible = "regulator-fixed";
+		regulator-name = "vddio_disp";
+		gpio = <&tlmm 34 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <300>;
+		enable-active-high;
+		regulator-boot-on;
+		vin-supply = <&pm8226_l8>;
+		pinctrl-0 = <&disp_vddio_default>;
+		pinctrl-names = "default";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		framebuffer@3200000 {
+			reg = <0x03200000 0x800000>;
+			no-map;
+		};
+
+		smem_region: smem@fa00000 {
+			reg = <0x0fa00000 0x100000>;
+			no-map;
+		};
+	};
+};
+
+&blsp1_i2c2 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	magnetometer@c {
+		compatible = "asahi-kasei,ak8963";
+		reg = <0xc>;
+		interrupts-extended = <&tlmm 38 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
+		vdd-supply = <&pm8226_l19>;
+		pinctrl-0 = <&mag_int_default &mag_reset_default>;
+		pinctrl-names = "default";
+	};
+
+	accelerometer@18 {
+		compatible = "st,lis3dh-accel";
+		reg = <0x18>;
+		interrupts-extended = <&tlmm 1 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8226_l19>;
+		pinctrl-0 = <&accel_int_default>;
+		pinctrl-names = "default";
+		st,drdy-int-pin = <1>;
+	};
+};
+
+&blsp1_i2c3 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	regulator@3e {
+		compatible = "ti,tps65132";
+		reg = <0x3e>;
+		pinctrl-0 = <&reg_lcd_default>;
+		pinctrl-names = "default";
+
+		reg_lcd_pos: outp {
+			regulator-name = "outp";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <6000000>;
+			regulator-active-discharge = <1>;
+			regulator-boot-on;
+			enable-gpios = <&tlmm 31 GPIO_ACTIVE_HIGH>;
+		};
+
+		reg_lcd_neg: outn {
+			regulator-name = "outn";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <6000000>;
+			regulator-active-discharge = <1>;
+			regulator-boot-on;
+			enable-gpios = <&tlmm 33 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	sensor@48 {
+		compatible = "ti,tmp108";
+		reg = <0x48>;
+		interrupts-extended = <&tlmm 13 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-0 = <&temp_alert_default>;
+		pinctrl-names = "default";
+		#thermal-sensor-cells = <0>;
+	};
+};
+
+&blsp1_uart3 {
+	status = "okay";
+};
+
+&pm8226_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+	status = "okay";
+};
+
+&pm8226_vib {
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-pm8226-regulators";
+
+		pm8226_s3: s3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8226_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2200000>;
+		};
+
+		pm8226_s5: s5 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8226_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l3: l3 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1337500>;
+		};
+
+		pm8226_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l5: l5 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-allow-set-load;
+		};
+
+		pm8226_l7: l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <1850000>;
+		};
+
+		pm8226_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l9: l9 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l14: l14 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+		};
+
+		pm8226_l15: l15 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+
+		pm8226_l16: l16 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3350000>;
+		};
+
+		pm8226_l17: l17 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l18: l18 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l19: l19 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8226_l20: l20 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+
+		pm8226_l21: l21 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-allow-set-load;
+		};
+
+		pm8226_l22: l22 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l24: l24 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8226_l25: l25 {
+			regulator-min-microvolt = <1775000>;
+			regulator-max-microvolt = <2125000>;
+		};
+
+		pm8226_l26: l26 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8226_l27: l27 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l28: l28 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3400000>;
+			regulator-boot-on;
+		};
+
+		pm8226_lvs1: lvs1 {
+			/* Pull-up for I2C lines */
+			regulator-always-on;
+		};
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&pm8226_l17>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	bus-width = <8>;
+	non-removable;
+
+	status = "okay";
+};
+
+&sdhc_2 {
+	vmmc-supply = <&pm8226_l18>;
+	vqmmc-supply = <&pm8226_l21>;
+
+	bus-width = <4>;
+	cd-gpios = <&tlmm 115 GPIO_ACTIVE_HIGH>;
+
+	status = "okay";
+};
+
+&smbb {
+	qcom,fast-charge-safe-current = <2000000>;
+	qcom,fast-charge-current-limit = <1900000>;
+	qcom,fast-charge-safe-voltage = <4400000>;
+	qcom,minimum-input-voltage = <4300000>;
+
+	status = "okay";
+};
+
+&tlmm {
+	accel_int_default: accel-int-default-state {
+		pins = "gpio1";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-disable;
+	};
+
+	disp_vddio_default: disp-vddio-default-state {
+		pins = "gpio34";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-high;
+	};
+
+	mag_int_default: mag-int-default-state {
+		pins = "gpio38";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-disable;
+	};
+
+	mag_reset_default: mag-reset-default-state {
+		pins = "gpio62";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-high;
+	};
+
+	reg_lcd_default: reg-lcd-default-state {
+		pins = "gpio31", "gpio33";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-high;
+	};
+
+	temp_alert_default: temp-alert-default-state {
+		pins = "gpio13";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-disable;
+	};
+};
+
+&usb {
+	extcon = <&smbb>;
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usb_hs_phy {
+	extcon = <&smbb>;
+	v1p8-supply = <&pm8226_l10>;
+	v3p3-supply = <&pm8226_l20>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8926-samsung-matisselte.dts b/arch/arm/boot/dts/qcom/qcom-msm8926-samsung-matisselte.dts
new file mode 100644
index 000000000000..73e19176eb97
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8926-samsung-matisselte.dts
@@ -0,0 +1,42 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Matti Lehtimäki <matti.lehtimaki@gmail.com>
+ * Copyright (c) 2023, Stefan Hansson <newbyte@postmarketos.org>
+ */
+
+/dts-v1/;
+
+#include "msm8926.dtsi"
+#include "qcom-msm8226-samsung-matisse-common.dtsi"
+
+/ {
+	model = "Samsung Galaxy Tab 4 10.1 LTE";
+	compatible = "samsung,matisselte", "qcom,msm8926", "qcom,msm8226";
+	chassis-type = "tablet";
+
+	reg_tsp_3p3v: regulator-tsp-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "tsp_3p3v";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 32 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_en1_default_state>;
+	};
+};
+
+&modem {
+	mss-supply = <&pm8226_s5>;
+};
+
+&tlmm {
+	tsp_en1_default_state: tsp-en1-default-state {
+		pins = "gpio32";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts b/arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts
new file mode 100644
index 000000000000..36f4c997b0b3
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8960-cdp.dts
@@ -0,0 +1,353 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/input/input.h>
+
+#include "qcom-msm8960.dtsi"
+#include "pm8921.dtsi"
+
+/ {
+	model = "Qualcomm MSM8960 CDP";
+	compatible = "qcom,msm8960-cdp", "qcom,msm8960";
+
+	aliases {
+		serial0 = &gsbi5_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	ext_l2: gpio-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "ext_l2";
+		gpio = <&msmgpio 91 0>;
+		startup-delay-us = <10000>;
+		enable-active-high;
+	};
+};
+
+&gsbi1 {
+	qcom,mode = <GSBI_PROT_SPI>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_default>;
+	status = "okay";
+};
+
+&gsbi1_spi {
+	status = "okay";
+
+	ethernet@0 {
+		compatible = "micrel,ks8851";
+		reg = <0>;
+		interrupt-parent = <&msmgpio>;
+		interrupts = <90 IRQ_TYPE_LEVEL_LOW>;
+		spi-max-frequency = <5400000>;
+		vdd-supply = <&ext_l2>;
+		vdd-io-supply = <&pm8921_lvs6>;
+		reset-gpios = <&msmgpio 89 0>;
+	};
+};
+
+&gsbi5 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi5_serial {
+	status = "okay";
+};
+
+&msmgpio {
+	spi1_default: spi1-default-state {
+		 mosi-pins {
+			pins = "gpio6";
+			function = "gsbi1";
+			drive-strength = <12>;
+			bias-disable;
+		 };
+
+		 miso-pins {
+			pins = "gpio7";
+			function = "gsbi1";
+			drive-strength = <12>;
+			bias-disable;
+		 };
+
+		 cs-pins {
+			pins = "gpio8";
+			function = "gsbi1";
+			drive-strength = <12>;
+			bias-disable;
+			output-low;
+		 };
+
+		 clk-pins {
+			pins = "gpio9";
+			function = "gsbi1";
+			drive-strength = <12>;
+			bias-disable;
+		 };
+	};
+};
+
+&pm8921 {
+	interrupts-extended = <&msmgpio 104 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&pm8921_keypad {
+	linux,keymap = <
+		MATRIX_KEY(0, 0, KEY_VOLUMEUP)
+		MATRIX_KEY(0, 1, KEY_VOLUMEDOWN)
+		MATRIX_KEY(0, 2, KEY_CAMERA_FOCUS)
+		MATRIX_KEY(0, 3, KEY_CAMERA)
+		>;
+	keypad,num-rows = <1>;
+	keypad,num-columns = <5>;
+
+	status = "okay";
+};
+
+&rpm {
+	regulators {
+		compatible = "qcom,rpm-pm8921-regulators";
+		vin_lvs1_3_6-supply = <&pm8921_s4>;
+		vin_lvs2-supply = <&pm8921_s4>;
+		vin_lvs4_5_7-supply = <&pm8921_s4>;
+		vdd_ncp-supply = <&pm8921_l6>;
+		vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+		vdd_l21_l23_l29-supply = <&pm8921_s8>;
+		vdd_l24-supply = <&pm8921_s1>;
+		vdd_l25-supply = <&pm8921_s1>;
+		vdd_l27-supply = <&pm8921_s7>;
+		vdd_l28-supply = <&pm8921_s7>;
+
+		/* Buck SMPS */
+		pm8921_s1: s1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		pm8921_s2: s2 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8921_s3: s3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <4800000>;
+			bias-pull-down;
+		};
+
+		pm8921_s4: s4 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+			qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+		};
+
+		pm8921_s7: s7 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		pm8921_s8: s8 {
+			regulator-always-on;
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		/* PMOS LDO */
+		pm8921_l1: l1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			bias-pull-down;
+		};
+
+		pm8921_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8921_l3: l3 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			bias-pull-down;
+		};
+
+		pm8921_l4: l4 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l5: l5 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l6: l6 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l7: l7 {
+			regulator-always-on;
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l8: l8 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l9: l9 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l10: l10 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l11: l11 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+
+		pm8921_l12: l12 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8921_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l15: l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l16: l16 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l17: l17 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l18: l18 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			bias-pull-down;
+		};
+
+		pm8921_l21: l21 {
+			regulator-min-microvolt = <1900000>;
+			regulator-max-microvolt = <1900000>;
+			bias-pull-down;
+		};
+
+		pm8921_l22: l22 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+			bias-pull-down;
+		};
+
+		pm8921_l23: l23 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l24: l24 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1150000>;
+			bias-pull-down;
+		};
+
+		pm8921_l25: l25 {
+			regulator-always-on;
+			regulator-min-microvolt = <1250000>;
+			regulator-max-microvolt = <1250000>;
+			bias-pull-down;
+		};
+
+		/* Low Voltage Switch */
+		pm8921_lvs1: lvs1 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs2: lvs2 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs3: lvs3 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs4: lvs4 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs5: lvs5 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs6: lvs6 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs7: lvs7 {
+			bias-pull-down;
+		};
+
+		pm8921_ncp: ncp {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+		};
+	};
+};
+
+/* eMMC */
+&sdcc1 {
+	status = "okay";
+};
+
+/* External micro SD card */
+&sdcc3 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8960-pins.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8960-pins.dtsi
new file mode 100644
index 000000000000..f18753e9f5ef
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8960-pins.dtsi
@@ -0,0 +1,61 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+&msmgpio {
+	i2c3_default_state: i2c3-default-state {
+		i2c3-pins {
+			pins = "gpio16", "gpio17";
+			function = "gsbi3";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	i2c3_sleep_state: i2c3-sleep-state {
+		i2c3-pins {
+			pins = "gpio16", "gpio17";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-bus-hold;
+		};
+	};
+
+	sdcc3_default_state: sdcc3-default-state {
+		clk-pins {
+			pins = "sdc3_clk";
+			drive-strength = <8>;
+			bias-disable;
+		};
+
+		cmd-pins {
+			pins = "sdc3_cmd";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+
+		data-pins {
+			pins = "sdc3_data";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	sdcc3_sleep_state: sdcc3-sleep-state {
+		clk-pins {
+			pins = "sdc3_clk";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		cmd-pins {
+			pins = "sdc3_cmd";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		data-pins {
+			pins = "sdc3_data";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8960-samsung-expressatt.dts b/arch/arm/boot/dts/qcom/qcom-msm8960-samsung-expressatt.dts
new file mode 100644
index 000000000000..49d117ea033a
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8960-samsung-expressatt.dts
@@ -0,0 +1,410 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/reset/qcom,gcc-msm8960.h>
+
+#include "qcom-msm8960.dtsi"
+#include "pm8921.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/input/gpio-keys.h>
+
+/ {
+	model = "Samsung Galaxy Express SGH-I437";
+	compatible = "samsung,expressatt", "qcom,msm8960";
+	chassis-type = "handset";
+
+	aliases {
+		serial0 = &gsbi5_serial;
+		mmc0 = &sdcc1; /* SDCC1 eMMC slot */
+		mmc1 = &sdcc3; /* SDCC3 SD card slot */
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pin_a>;
+
+		key-home {
+			label = "Home";
+			gpios = <&msmgpio 40 GPIO_ACTIVE_LOW>;
+			debounce-interval = <5>;
+			linux,code = <KEY_HOMEPAGE>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&msmgpio 50 GPIO_ACTIVE_LOW>;
+			debounce-interval = <5>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&msmgpio 81 GPIO_ACTIVE_LOW>;
+			debounce-interval = <5>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+	};
+};
+
+&gsbi5 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi5_serial {
+	status = "okay";
+};
+
+&sdcc1 {
+	vmmc-supply = <&pm8921_l5>;
+	status = "okay";
+};
+
+&sdcc3 {
+	vmmc-supply = <&pm8921_l6>;
+	vqmmc-supply = <&pm8921_l7>;
+
+	pinctrl-0 = <&sdcc3_default_state>;
+	pinctrl-1 = <&sdcc3_sleep_state>;
+	pinctrl-names = "default", "sleep";
+
+	status = "okay";
+};
+
+&gsbi1 {
+	qcom,mode = <GSBI_PROT_SPI>;
+	pinctrl-0 = <&spi1_default>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&gsbi1_spi {
+	status = "okay";
+};
+
+&gsbi3 {
+	qcom,mode = <GSBI_PROT_I2C>;
+	status = "okay";
+};
+
+&gsbi3_i2c {
+	status = "okay";
+
+	// Atmel mXT224S touchscreen
+	touchscreen@4a {
+		compatible = "atmel,maxtouch";
+		reg = <0x4a>;
+		interrupt-parent = <&msmgpio>;
+		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
+		vdda-supply = <&pm8921_lvs6>;
+		vdd-supply = <&pm8921_l17>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&touchscreen>;
+	};
+};
+
+&msmgpio {
+	spi1_default: spi1-default-state {
+		mosi-pins {
+			pins = "gpio6";
+			function = "gsbi1";
+			drive-strength = <12>;
+			bias-disable;
+		};
+
+		miso-pins {
+			pins = "gpio7";
+			function = "gsbi1";
+			drive-strength = <12>;
+			bias-disable;
+		};
+
+		cs-pins {
+			pins = "gpio8";
+			function = "gsbi1";
+			drive-strength = <12>;
+			bias-disable;
+			output-low;
+		};
+
+		clk-pins {
+			pins = "gpio9";
+			function = "gsbi1";
+			drive-strength = <12>;
+			bias-disable;
+		};
+	};
+
+	gpio_keys_pin_a: gpio-keys-active-state {
+		pins = "gpio40", "gpio50", "gpio81";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	touchscreen: touchscreen-int-state {
+		pins = "gpio11";
+		function = "gpio";
+		output-enable;
+		bias-disable;
+		drive-strength = <2>;
+	};
+};
+
+&pm8921 {
+	interrupts-extended = <&msmgpio 104 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&rpm {
+	regulators {
+		compatible = "qcom,rpm-pm8921-regulators";
+		vin_lvs1_3_6-supply = <&pm8921_s4>;
+		vin_lvs2-supply = <&pm8921_s4>;
+		vin_lvs4_5_7-supply = <&pm8921_s4>;
+		vdd_ncp-supply = <&pm8921_l6>;
+		vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+		vdd_l21_l23_l29-supply = <&pm8921_s8>;
+		vdd_l24-supply = <&pm8921_s1>;
+		vdd_l25-supply = <&pm8921_s1>;
+		vdd_l27-supply = <&pm8921_s7>;
+		vdd_l28-supply = <&pm8921_s7>;
+
+		/* Buck SMPS */
+		pm8921_s1: s1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		pm8921_s2: s2 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8921_s3: s3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <4800000>;
+			bias-pull-down;
+		};
+
+		pm8921_s4: s4 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+			qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+		};
+
+		pm8921_s7: s7 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		pm8921_s8: s8 {
+			regulator-always-on;
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		/* PMOS LDO */
+		pm8921_l1: l1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			bias-pull-down;
+		};
+
+		pm8921_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8921_l3: l3 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+
+		pm8921_l4: l4 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l5: l5 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l6: l6 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l7: l7 {
+			regulator-always-on;
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l8: l8 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3100000>;
+			bias-pull-down;
+		};
+
+		pm8921_l9: l9 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+
+		pm8921_l10: l10 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l11: l11 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+
+		pm8921_l12: l12 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8921_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l15: l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l16: l16 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l17: l17 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			bias-pull-down;
+		};
+
+		pm8921_l18: l18 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1500000>;
+			bias-pull-down;
+		};
+
+		pm8921_l21: l21 {
+			regulator-min-microvolt = <1900000>;
+			regulator-max-microvolt = <1900000>;
+			bias-pull-down;
+		};
+
+		pm8921_l22: l22 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+			bias-pull-down;
+		};
+
+		pm8921_l23: l23 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l24: l24 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1150000>;
+			bias-pull-down;
+		};
+
+		pm8921_l25: l25 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			bias-pull-down;
+		};
+
+		/* Low Voltage Switch */
+		pm8921_lvs1: lvs1 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs2: lvs2 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs3: lvs3 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs4: lvs4 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs5: lvs5 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs6: lvs6 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs7: lvs7 {
+			bias-pull-down;
+		};
+
+		pm8921_ncp: ncp {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+		};
+	};
+};
+
+&usb_hs1_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l4>;
+};
+
+&usb1 {
+	dr_mode = "otg";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8960-sony-huashan.dts b/arch/arm/boot/dts/qcom/qcom-msm8960-sony-huashan.dts
new file mode 100644
index 000000000000..f2f59fc8b9b6
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8960-sony-huashan.dts
@@ -0,0 +1,361 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2025, Antony Kurniawan Soemardi <linux@smankusors.com>
+ */
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/reset/qcom,gcc-msm8960.h>
+
+#include "qcom-msm8960.dtsi"
+#include "pm8921.dtsi"
+
+/ {
+	model = "Sony Xperia SP";
+	compatible = "sony,huashan", "qcom,msm8960t", "qcom,msm8960";
+	chassis-type = "handset";
+
+	aliases {
+		serial0 = &gsbi8_serial;
+		mmc0 = &sdcc1; /* SDCC1 eMMC slot */
+		mmc1 = &sdcc3; /* SDCC3 SD card slot */
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&pm8921_gpio 21 GPIO_ACTIVE_LOW>;
+			debounce-interval = <10>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&pm8921_gpio 20 GPIO_ACTIVE_LOW>;
+			debounce-interval = <10>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+	};
+};
+
+&gsbi8 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi8_serial {
+	status = "okay";
+};
+
+&pm8921 {
+	interrupts-extended = <&msmgpio 104 IRQ_TYPE_LEVEL_LOW>;
+};
+
+&pm8921_gpio {
+	keypad_default_state: keypad-default-state {
+		keypad-sense-pins {
+			pins = "gpio1", "gpio2", "gpio3", "gpio4", "gpio5";
+			function = PMIC_GPIO_FUNC_NORMAL;
+			bias-pull-up;
+			input-enable;
+			power-source = <PM8921_GPIO_S4>;
+			qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+			qcom,pull-up-strength = <PMIC_GPIO_PULL_UP_31P5>;
+		};
+
+		keypad-drive-pins {
+			pins = "gpio9", "gpio10";
+			function = PMIC_GPIO_FUNC_FUNC1;
+			bias-disable;
+			drive-open-drain;
+			output-low;
+			power-source = <PM8921_GPIO_S4>;
+			qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+		};
+	};
+};
+
+&pm8921_keypad {
+	linux,keymap = <
+		MATRIX_KEY(1, 0, KEY_CAMERA_FOCUS)
+		MATRIX_KEY(1, 1, KEY_CAMERA)
+	>;
+	keypad,num-rows = <2>;
+	keypad,num-columns = <5>;
+
+	pinctrl-0 = <&keypad_default_state>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&rpm {
+	regulators {
+		compatible = "qcom,rpm-pm8921-regulators";
+		vin_lvs1_3_6-supply = <&pm8921_s4>;
+		vin_lvs2-supply = <&pm8921_s4>;
+		vin_lvs4_5_7-supply = <&pm8921_s4>;
+		vdd_ncp-supply = <&pm8921_l6>;
+		vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+		vdd_l21_l23_l29-supply = <&pm8921_s8>;
+		vdd_l24-supply = <&pm8921_s1>;
+		vdd_l25-supply = <&pm8921_s1>;
+		vdd_l26-supply = <&pm8921_s7>;
+		vdd_l27-supply = <&pm8921_s7>;
+		vdd_l28-supply = <&pm8921_s7>;
+		vdd_l29-supply = <&pm8921_s8>;
+
+		/* Buck SMPS */
+		pm8921_s1: s1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		pm8921_s2: s2 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8921_s3: s3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <4800000>;
+			bias-pull-down;
+		};
+
+		pm8921_s4: s4 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+			qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+		};
+
+		pm8921_s7: s7 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		pm8921_s8: s8 {
+			regulator-always-on;
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		/* PMOS LDO */
+		pm8921_l1: l1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			bias-pull-down;
+		};
+
+		pm8921_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8921_l3: l3 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			bias-pull-down;
+		};
+
+		pm8921_l4: l4 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l5: l5 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l6: l6 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l7: l7 {
+			regulator-always-on;
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l8: l8 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l9: l9 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+
+		pm8921_l10: l10 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l11: l11 {
+			regulator-min-microvolt = <2600000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l12: l12 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8921_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l15: l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l16: l16 {
+			regulator-min-microvolt = <2600000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l17: l17 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l18: l18 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8921_l21: l21 {
+			regulator-min-microvolt = <1900000>;
+			regulator-max-microvolt = <1900000>;
+			bias-pull-down;
+		};
+
+		pm8921_l22: l22 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+			bias-pull-down;
+		};
+
+		pm8921_l23: l23 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l24: l24 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1150000>;
+			bias-pull-down;
+		};
+
+		pm8921_l25: l25 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			bias-pull-down;
+		};
+
+		/* Low Voltage Switch */
+		pm8921_lvs1: lvs1 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs2: lvs2 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs3: lvs3 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs4: lvs4 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs5: lvs5 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs6: lvs6 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs7: lvs7 {
+			bias-pull-down;
+		};
+
+		pm8921_ncp: ncp {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+		};
+	};
+};
+
+&sdcc1 {
+	vmmc-supply = <&pm8921_l5>;
+	status = "okay";
+};
+
+&sdcc3 {
+	vmmc-supply = <&pm8921_l6>;
+	vqmmc-supply = <&pm8921_l7>;
+
+	pinctrl-0 = <&sdcc3_default_state>;
+	pinctrl-1 = <&sdcc3_sleep_state>;
+	pinctrl-names = "default", "sleep";
+
+	status = "okay";
+};
+
+&usb_hs1_phy {
+	v3p3-supply = <&pm8921_l3>;
+	v1p8-supply = <&pm8921_l4>;
+};
+
+&usb1 {
+	dr_mode = "otg";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi
new file mode 100644
index 000000000000..6e272d5345a8
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi
@@ -0,0 +1,525 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,gcc-msm8960.h>
+#include <dt-bindings/reset/qcom,gcc-msm8960.h>
+#include <dt-bindings/clock/qcom,lcc-msm8960.h>
+#include <dt-bindings/mfd/qcom-rpm.h>
+#include <dt-bindings/soc/qcom,gsbi.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	model = "Qualcomm MSM8960";
+	compatible = "qcom,msm8960";
+	interrupt-parent = <&intc>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupts = <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
+
+		cpu@0 {
+			compatible = "qcom,krait";
+			enable-method = "qcom,kpss-acc-v1";
+			device_type = "cpu";
+			reg = <0>;
+			next-level-cache = <&l2>;
+			qcom,acc = <&acc0>;
+			qcom,saw = <&saw0>;
+		};
+
+		cpu@1 {
+			compatible = "qcom,krait";
+			enable-method = "qcom,kpss-acc-v1";
+			device_type = "cpu";
+			reg = <1>;
+			next-level-cache = <&l2>;
+			qcom,acc = <&acc1>;
+			qcom,saw = <&saw1>;
+		};
+
+		l2: l2-cache {
+			compatible = "cache";
+			cache-level = <2>;
+			cache-unified;
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0>;
+	};
+
+	thermal-zones {
+		cpu0-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&tsens 0>;
+
+			trips {
+				cpu_alert0: trip0 {
+					temperature = <60000>;
+					hysteresis = <10000>;
+					type = "passive";
+				};
+
+				cpu_crit0: trip1 {
+					temperature = <95000>;
+					hysteresis = <10000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu1-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&tsens 1>;
+
+			trips {
+				cpu_alert1: trip0 {
+					temperature = <60000>;
+					hysteresis = <10000>;
+					type = "passive";
+				};
+
+				cpu_crit1: trip1 {
+					temperature = <95000>;
+					hysteresis = <10000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	cpu-pmu {
+		compatible = "qcom,krait-pmu";
+		interrupts = <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
+		qcom,no-pc-write;
+	};
+
+	clocks {
+		cxo_board: cxo_board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <19200000>;
+			clock-output-names = "cxo_board";
+		};
+
+		pxo_board: pxo_board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <27000000>;
+			clock-output-names = "pxo_board";
+		};
+
+		sleep_clk: sleep_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+			clock-output-names = "sleep_clk";
+		};
+	};
+
+	/* Temporary fixed regulator */
+	vsdcc_fixed: vsdcc-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "SDCC Power";
+		regulator-min-microvolt = <2700000>;
+		regulator-max-microvolt = <2700000>;
+		regulator-always-on;
+	};
+
+	soc: soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		compatible = "simple-bus";
+
+		intc: interrupt-controller@2000000 {
+			compatible = "qcom,msm-qgic2";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			reg = <0x02000000 0x1000>,
+			      <0x02002000 0x1000>;
+		};
+
+		timer@200a000 {
+			compatible = "qcom,kpss-wdt-msm8960", "qcom,kpss-timer",
+				     "qcom,msm-timer";
+			interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_EDGE_RISING)>,
+				     <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_EDGE_RISING)>,
+				     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_EDGE_RISING)>;
+			reg = <0x0200a000 0x100>;
+			clock-frequency = <27000000>;
+			clocks = <&sleep_clk>;
+			clock-names = "sleep";
+			cpu-offset = <0x80000>;
+		};
+
+		qfprom: efuse@700000 {
+			compatible = "qcom,msm8960-qfprom", "qcom,qfprom";
+			reg = <0x00700000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			tsens_calib: calib@404 {
+				reg = <0x404 0x10>;
+			};
+
+			tsens_backup: backup-calib@414 {
+				reg = <0x414 0x10>;
+			};
+		};
+
+		msmgpio: pinctrl@800000 {
+			compatible = "qcom,msm8960-pinctrl";
+			gpio-controller;
+			gpio-ranges = <&msmgpio 0 0 152>;
+			#gpio-cells = <2>;
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			reg = <0x800000 0x4000>;
+		};
+
+		gcc: clock-controller@900000 {
+			compatible = "qcom,gcc-msm8960", "syscon";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			reg = <0x900000 0x4000>;
+			clocks = <&cxo_board>,
+				 <&pxo_board>,
+				 <&lcc PLL4>;
+			clock-names = "cxo", "pxo", "pll4";
+
+			tsens: thermal-sensor {
+				compatible = "qcom,msm8960-tsens";
+
+				nvmem-cells = <&tsens_calib>, <&tsens_backup>;
+				nvmem-cell-names = "calib", "calib_backup";
+				interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "uplow";
+
+				#qcom,sensors = <5>;
+				#thermal-sensor-cells = <1>;
+			};
+		};
+
+		lcc: clock-controller@28000000 {
+			compatible = "qcom,lcc-msm8960";
+			reg = <0x28000000 0x1000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			clocks = <&pxo_board>,
+				 <&gcc PLL4_VOTE>,
+				 <0>,
+				 <0>, <0>,
+				 <0>, <0>,
+				 <0>;
+			clock-names = "pxo",
+				      "pll4_vote",
+				      "mi2s_codec_clk",
+				      "codec_i2s_mic_codec_clk",
+				      "spare_i2s_mic_codec_clk",
+				      "codec_i2s_spkr_codec_clk",
+				      "spare_i2s_spkr_codec_clk",
+				      "pcm_codec_clk";
+		};
+
+		clock-controller@4000000 {
+			compatible = "qcom,mmcc-msm8960";
+			reg = <0x4000000 0x1000>;
+			#clock-cells = <1>;
+			#power-domain-cells = <1>;
+			#reset-cells = <1>;
+			clocks = <&pxo_board>,
+				 <&gcc PLL3>,
+				 <&gcc PLL8_VOTE>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>;
+			clock-names = "pxo",
+				      "pll3",
+				      "pll8_vote",
+				      "dsi1pll",
+				      "dsi1pllbyte",
+				      "dsi2pll",
+				      "dsi2pllbyte",
+				      "hdmipll";
+		};
+
+		l2cc: clock-controller@2011000 {
+			compatible = "qcom,kpss-gcc-msm8960", "qcom,kpss-gcc", "syscon";
+			reg = <0x2011000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			#clock-cells = <0>;
+		};
+
+		rpm: rpm@108000 {
+			compatible = "qcom,rpm-msm8960";
+			reg = <0x108000 0x1000>;
+			qcom,ipc = <&l2cc 0x8 2>;
+
+			interrupts = <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "ack", "err", "wakeup";
+		};
+
+		acc0: clock-controller@2088000 {
+			compatible = "qcom,kpss-acc-v1";
+			reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			clock-output-names = "acpu0_aux";
+			#clock-cells = <0>;
+		};
+
+		acc1: clock-controller@2098000 {
+			compatible = "qcom,kpss-acc-v1";
+			reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			clock-output-names = "acpu1_aux";
+			#clock-cells = <0>;
+		};
+
+		saw0: power-manager@2089000 {
+			compatible = "qcom,msm8960-saw2-cpu", "qcom,saw2";
+			reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
+
+			saw0_vreg: regulator {
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1300000>;
+			};
+		};
+
+		saw1: power-manager@2099000 {
+			compatible = "qcom,msm8960-saw2-cpu", "qcom,saw2";
+			reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
+
+			saw1_vreg: regulator {
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1300000>;
+			};
+		};
+
+		gsbi5: gsbi@16400000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <5>;
+			reg = <0x16400000 0x100>;
+			clocks = <&gcc GSBI5_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+
+			status = "disabled";
+
+			gsbi5_serial: serial@16440000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x16440000 0x1000>,
+				      <0x16400000 0x1000>;
+				interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+		};
+
+		gsbi8: gsbi@1a000000  {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <8>;
+			reg = <0x1a000000 0x100>;
+			clocks = <&gcc GSBI8_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+
+			status = "disabled";
+
+			gsbi8_serial: serial@1a040000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x1a040000 0x1000>,
+				      <0x1a000000 0x1000>;
+				interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI8_UART_CLK>,
+					 <&gcc GSBI8_H_CLK>;
+				clock-names = "core",
+					      "iface";
+
+				status = "disabled";
+			};
+		};
+
+		ssbi: ssbi@500000 {
+			compatible = "qcom,ssbi";
+			reg = <0x500000 0x1000>;
+			qcom,controller-type = "pmic-arbiter";
+		};
+
+		rng@1a500000 {
+			compatible = "qcom,prng";
+			reg = <0x1a500000 0x200>;
+			clocks = <&gcc PRNG_CLK>;
+			clock-names = "core";
+		};
+
+		sdcc3: mmc@12180000 {
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00051180>;
+			status = "disabled";
+			reg = <0x12180000 0x2000>;
+			interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <192000000>;
+			no-1-8-v;
+			vmmc-supply = <&vsdcc_fixed>;
+			dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
+			dma-names = "tx", "rx";
+		};
+
+		sdcc3bam: dma-controller@12182000 {
+			compatible = "qcom,bam-v1.3.0";
+			reg = <0x12182000 0x4000>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC3_H_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		sdcc1: mmc@12400000 {
+			status = "disabled";
+			compatible = "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x00051180>;
+			reg = <0x12400000 0x2000>;
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
+			clock-names = "mclk", "apb_pclk";
+			bus-width = <8>;
+			max-frequency = <96000000>;
+			non-removable;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			vmmc-supply = <&vsdcc_fixed>;
+			dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
+			dma-names = "tx", "rx";
+		};
+
+		sdcc1bam: dma-controller@12402000 {
+			compatible = "qcom,bam-v1.3.0";
+			reg = <0x12402000 0x4000>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC1_H_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		tcsr: syscon@1a400000 {
+			compatible = "qcom,tcsr-msm8960", "syscon";
+			reg = <0x1a400000 0x100>;
+		};
+
+		gsbi1: gsbi@16000000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <1>;
+			reg = <0x16000000 0x100>;
+			clocks = <&gcc GSBI1_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			status = "disabled";
+
+			gsbi1_spi: spi@16080000 {
+				compatible = "qcom,spi-qup-v1.1.1";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x16080000 0x1000>;
+				interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
+				cs-gpios = <&msmgpio 8 0>;
+
+				clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+		};
+
+		usb1: usb@12500000 {
+			compatible = "qcom,ci-hdrc";
+			reg = <0x12500000 0x200>,
+			      <0x12500200 0x200>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc USB_HS1_XCVR_CLK>, <&gcc USB_HS1_H_CLK>;
+			clock-names = "core", "iface";
+			assigned-clocks = <&gcc USB_HS1_XCVR_CLK>;
+			assigned-clock-rates = <60000000>;
+			resets = <&gcc USB_HS1_RESET>;
+			reset-names = "core";
+			phy_type = "ulpi";
+			ahb-burst-config = <0>;
+			phys = <&usb_hs1_phy>;
+			phy-names = "usb-phy";
+			#reset-cells = <1>;
+			status = "disabled";
+
+			ulpi {
+				usb_hs1_phy: phy {
+					compatible = "qcom,usb-hs-phy-msm8960",
+						     "qcom,usb-hs-phy";
+					clocks = <&sleep_clk>, <&cxo_board>;
+					clock-names = "sleep", "ref";
+					resets = <&usb1 0>;
+					reset-names = "por";
+					#phy-cells = <0>;
+				};
+			};
+		};
+
+		gsbi3: gsbi@16200000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			reg = <0x16200000 0x100>;
+			ranges;
+			cell-index = <3>;
+			clocks = <&gcc GSBI3_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			status = "disabled";
+
+			gsbi3_i2c: i2c@16280000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x16280000 0x1000>;
+				pinctrl-0 = <&i2c3_default_state>;
+				pinctrl-1 = <&i2c3_sleep_state>;
+				pinctrl-names = "default", "sleep";
+				interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI3_QUP_CLK>,
+					 <&gcc GSBI3_H_CLK>;
+				clock-names = "core", "iface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+	};
+};
+#include "qcom-msm8960-pins.dtsi"
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974-lge-nexus5-hammerhead.dts b/arch/arm/boot/dts/qcom/qcom-msm8974-lge-nexus5-hammerhead.dts
new file mode 100644
index 000000000000..b3127f0383cf
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974-lge-nexus5-hammerhead.dts
@@ -0,0 +1,728 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974.dtsi"
+#include "pm8841.dtsi"
+#include "pm8941.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+	model = "LGE MSM 8974 HAMMERHEAD";
+	compatible = "lge,hammerhead", "qcom,msm8974";
+	chassis-type = "handset";
+
+	aliases {
+		mmc0 = &sdhc_1;
+		serial0 = &blsp1_uart1;
+		serial1 = &blsp2_uart4;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pin_a>;
+
+		key-volume-up {
+			label = "volume_up";
+			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		key-volume-down {
+			label = "volume_down";
+			gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+	};
+
+	clk_pwm: pwm {
+		compatible = "clk-pwm";
+		clocks = <&mmcc CAMSS_GP1_CLK>;
+
+		pinctrl-0 = <&vibrator_pin>;
+		pinctrl-names = "default";
+
+		#pwm-cells = <2>;
+	};
+
+	vibrator {
+		compatible = "pwm-vibrator";
+		pwms = <&clk_pwm 0 100000>;
+		pwm-names = "enable";
+
+		vcc-supply = <&pm8941_l19>;
+		enable-gpios = <&tlmm 60 GPIO_ACTIVE_HIGH>;
+	};
+
+	vreg_boost: vreg-boost {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vreg-boost";
+		regulator-min-microvolt = <3150000>;
+		regulator-max-microvolt = <3150000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		gpio = <&pm8941_gpios 21 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&boost_bypass_n_pin>;
+	};
+
+	vreg_vph_pwr: vreg-vph-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "vph-pwr";
+
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+
+		regulator-always-on;
+	};
+
+	vreg_wlan: wlan-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 26 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_regulator_pin>;
+	};
+};
+
+&blsp1_i2c1 {
+	status = "okay";
+	clock-frequency = <100000>;
+
+	charger: bq24192@6b {
+		compatible = "ti,bq24192";
+		reg = <0x6b>;
+		interrupts-extended = <&spmi_bus 0 0xd5 0 IRQ_TYPE_EDGE_FALLING>;
+
+		omit-battery-class;
+
+		usb_otg_vbus: usb-otg-vbus { };
+	};
+
+	fuelgauge: max17048@36 {
+		compatible = "maxim,max17048";
+		reg = <0x36>;
+
+		maxim,double-soc;
+		maxim,rcomp = /bits/ 8 <0x4d>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&fuelgauge_pin>;
+
+		maxim,alert-low-soc-level = <2>;
+	};
+};
+
+&blsp1_i2c2 {
+	status = "okay";
+	clock-frequency = <355000>;
+
+	synaptics@70 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x70>;
+
+		interrupts-extended = <&tlmm 5 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8941_l22>;
+		vio-supply = <&pm8941_lvs3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&touch_pin>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmi4-f01@1 {
+			reg = <0x1>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp1_i2c3 {
+	status = "okay";
+	clock-frequency = <100000>;
+
+	sensor@39 {
+		compatible = "avago,apds9930";
+		reg = <0x39>;
+		interrupts-extended = <&tlmm 61 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8941_l17>;
+		vddio-supply = <&pm8941_lvs1>;
+		led-max-microamp = <100000>;
+		amstaos,proximity-diodes = <0>;
+	};
+};
+
+&blsp2_i2c5 {
+	status = "okay";
+	clock-frequency = <355000>;
+
+	backlight: led-controller@38 {
+		compatible = "ti,lm3630a";
+		status = "okay";
+		reg = <0x38>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@0 {
+			reg = <0>;
+			led-sources = <0 1>;
+			label = "lcd-backlight";
+			default-brightness = <200>;
+		};
+	};
+};
+
+&blsp2_i2c6 {
+	status = "okay";
+	clock-frequency = <100000>;
+
+	mpu6515@68 {
+		compatible = "invensense,mpu6515";
+		reg = <0x68>;
+		interrupts-extended = <&tlmm 73 IRQ_TYPE_EDGE_FALLING>;
+		vddio-supply = <&pm8941_lvs1>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&mpu6515_pin>;
+
+		mount-matrix = "0", "-1", "0",
+				"-1", "0", "0",
+				"0", "0", "1";
+
+		i2c-gate {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			ak8963@f {
+				compatible = "asahi-kasei,ak8963";
+				reg = <0x0f>;
+				gpios = <&tlmm 67 GPIO_ACTIVE_HIGH>;
+				vid-supply = <&pm8941_lvs1>;
+				vdd-supply = <&pm8941_l17>;
+			};
+
+			bmp280@76 {
+				compatible = "bosch,bmp280";
+				reg = <0x76>;
+				vdda-supply = <&pm8941_lvs1>;
+				vddd-supply = <&pm8941_l17>;
+			};
+		};
+	};
+};
+
+&blsp1_uart1 {
+	status = "okay";
+};
+
+&blsp2_uart4 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <3000000>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_pin>;
+
+		host-wakeup-gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&tlmm 62 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&tlmm 41 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dsi0 {
+	status = "okay";
+
+	vdda-supply = <&pm8941_l2>;
+	vdd-supply = <&pm8941_lvs3>;
+	vddio-supply = <&pm8941_l12>;
+
+	panel: panel@0 {
+		reg = <0>;
+		compatible = "lg,acx467akm-7";
+
+		backlight = <&backlight>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&panel_pin>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&mdss_dsi0_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&panel_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+	status = "okay";
+
+	vddio-supply = <&pm8941_l12>;
+};
+
+&pm8941_gpios {
+	gpio_keys_pin_a: gpio-keys-active-state {
+		pins = "gpio2", "gpio3";
+		function = "normal";
+
+		bias-pull-up;
+		power-source = <PM8941_GPIO_S3>;
+	};
+
+	fuelgauge_pin: fuelgauge-int-state {
+		pins = "gpio9";
+		function = "normal";
+
+		bias-disable;
+		input-enable;
+		power-source = <PM8941_GPIO_S3>;
+	};
+
+	wlan_sleep_clk_pin: wl-sleep-clk-state {
+		pins = "gpio16";
+		function = "func2";
+
+		output-high;
+		power-source = <PM8941_GPIO_S3>;
+	};
+
+	wlan_regulator_pin: wl-reg-active-state {
+		pins = "gpio17";
+		function = "normal";
+
+		bias-disable;
+		power-source = <PM8941_GPIO_S3>;
+	};
+
+	otg-hog {
+		gpio-hog;
+		gpios = <35 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "otg-gpio";
+	};
+};
+
+&pm8941_lpg {
+	status = "okay";
+
+	qcom,power-source = <1>;
+
+	multi-led {
+		color = <LED_COLOR_ID_RGB>;
+		function = LED_FUNCTION_STATUS;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@7 {
+			reg = <7>;
+			color = <LED_COLOR_ID_RED>;
+		};
+
+		led@6 {
+			reg = <6>;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+
+		led@5 {
+			reg = <5>;
+			color = <LED_COLOR_ID_BLUE>;
+		};
+	};
+};
+
+&remoteproc_adsp {
+	cx-supply = <&pm8841_s2>;
+	status = "okay";
+};
+
+&remoteproc_mss {
+	cx-supply = <&pm8841_s2>;
+	mss-supply = <&pm8841_s3>;
+	mx-supply = <&pm8841_s1>;
+	pll-supply = <&pm8941_l12>;
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pm8841-regulators";
+
+		pm8841_s1: s1 {
+			regulator-min-microvolt = <675000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s2: s2 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s3: s3 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s4: s4 {
+			regulator-min-microvolt = <815000>;
+			regulator-max-microvolt = <900000>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,rpm-pm8941-regulators";
+
+		vdd_l1_l3-supply = <&pm8941_s1>;
+		vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+		vdd_l4_l11-supply = <&pm8941_s1>;
+		vdd_l5_l7-supply = <&pm8941_s2>;
+		vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+		vdd_l8_l16_l18_l19-supply = <&vreg_vph_pwr>;
+		vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+		vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+		vdd_l21-supply = <&vreg_boost>;
+
+		pm8941_s1: s1 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_s2: s2 {
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+			regulator-boot-on;
+		};
+
+		pm8941_s3: s3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l3: l3 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l4: l4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l11: l11 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8941_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l13: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l15: l15 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8941_l16: l16 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l17: l17 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l18: l18 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l19: l19 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8941_l20: l20 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+			regulator-boot-on;
+		};
+
+		pm8941_l21: l21 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l22: l22 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8941_l23: l23 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8941_l24: l24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			regulator-boot-on;
+		};
+
+		pm8941_lvs1: lvs1 {};
+		pm8941_lvs3: lvs3 {};
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	vmmc-supply = <&pm8941_l20>;
+	vqmmc-supply = <&pm8941_s3>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	max-frequency = <100000000>;
+	vmmc-supply = <&vreg_wlan>;
+	vqmmc-supply = <&pm8941_s3>;
+	non-removable;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_on>;
+	pinctrl-1 = <&sdc2_off>;
+
+	wifi@1 {
+		compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
+
+		brcm,drive-strength = <10>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_sleep_clk_pin>;
+	};
+};
+
+&tlmm {
+	sdc1_on: sdc1-on-state {
+		clk-pins {
+			pins = "sdc1_clk";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc1_cmd", "sdc1_data";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	sdc2_on: sdc2-on-state {
+		clk-pins {
+			pins = "sdc2_clk";
+			drive-strength = <6>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc2_cmd", "sdc2_data";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+	};
+
+	mpu6515_pin: mpu6515-state {
+		pins = "gpio73";
+		function = "gpio";
+		bias-disable;
+	};
+
+	touch_pin: touch-state {
+		int-pins {
+			pins = "gpio5";
+			function = "gpio";
+
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		reset-pins {
+			pins = "gpio8";
+			function = "gpio";
+
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	panel_pin: panel-state {
+		pins = "gpio12";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	bt_pin: bt-state {
+		hostwake-pins {
+			pins = "gpio42";
+			function = "gpio";
+		};
+
+		devwake-pins {
+			pins = "gpio62";
+			function = "gpio";
+		};
+
+		shutdown-pins {
+			pins = "gpio41";
+			function = "gpio";
+		};
+	};
+
+	vibrator_pin: vibrator-state {
+		core-pins {
+			pins = "gpio27";
+			function = "gp1_clk";
+			drive-strength = <6>;
+			bias-disable;
+		};
+
+		enable-pins {
+			pins = "gpio60";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+};
+
+&usb {
+	status = "okay";
+
+	phys = <&usb_hs1_phy>;
+	phy-select = <&tcsr 0xb000 0>;
+
+	extcon = <&charger>, <&usb_id>;
+	vbus-supply = <&usb_otg_vbus>;
+
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+};
+
+&usb_hs1_phy {
+	status = "okay";
+
+	v1p8-supply = <&pm8941_l6>;
+	v3p3-supply = <&pm8941_l24>;
+
+	qcom,init-seq = /bits/ 8 <0x1 0x64>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974-samsung-hlte.dts b/arch/arm/boot/dts/qcom/qcom-msm8974-samsung-hlte.dts
new file mode 100644
index 000000000000..b7a1367d3470
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974-samsung-hlte.dts
@@ -0,0 +1,446 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974.dtsi"
+#include "pm8841.dtsi"
+#include "pm8941.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+	model = "Samsung Galaxy Note 3";
+	compatible = "samsung,hlte", "qcom,msm8974";
+	chassis-type = "handset";
+
+	aliases {
+		mmc0 = &sdhc_1; /* SDC1 eMMC slot */
+		mmc1 = &sdhc_3; /* SDC3 SD card slot */
+		serial0 = &blsp1_uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&gpio_keys_pin_a>;
+		pinctrl-names = "default";
+
+		key-home {
+			label = "Home Key";
+			gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOMEPAGE>;
+			wakeup-source;
+			debounce-interval = <15>;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <15>;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <15>;
+		};
+	};
+
+	i2c-touchkey {
+		compatible = "i2c-gpio";
+
+		sda-gpios = <&tlmm 95 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&tlmm 96 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+		pinctrl-0 = <&i2c_touchkey_pins>;
+		pinctrl-names = "default";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		touchkey@20 {
+			compatible = "cypress,midas-touchkey";
+			reg = <0x20>;
+
+			interrupts-extended = <&pm8941_gpios 29 IRQ_TYPE_EDGE_FALLING>;
+
+			pinctrl-0 = <&touchkey_pin>;
+			pinctrl-names = "default";
+
+			vcc-supply = <&pm8941_lvs3>;
+			vdd-supply = <&pm8941_l13>;
+
+			linux,keycodes = <KEY_APPSELECT KEY_BACK>;
+		};
+	};
+
+	touch_ldo: regulator-touch {
+		compatible = "regulator-fixed";
+		regulator-name = "touch-ldo";
+
+		gpio = <&pm8941_gpios 9 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+
+		pinctrl-0 = <&touch_ldo_pin>;
+		pinctrl-names = "default";
+	};
+};
+
+&blsp1_i2c2 {
+	status = "okay";
+
+	touchscreen@20 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x20>;
+
+		interrupt-parent = <&pm8941_gpios>;
+		interrupts = <30 IRQ_TYPE_EDGE_FALLING>;
+
+		vdd-supply = <&pm8941_l10>;
+		vio-supply = <&touch_ldo>;
+
+		pinctrl-0 = <&touch_pin>;
+		pinctrl-names = "default";
+
+		syna,startup-delay-ms = <100>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmi4-f01@1 {
+			reg = <0x1>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp2_i2c6 {
+	status = "okay";
+
+	fuelgauge@36 {
+		compatible = "maxim,max17048";
+		reg = <0x36>;
+
+		maxim,double-soc;
+		maxim,rcomp = /bits/ 8 <0x56>;
+
+		interrupt-parent = <&pm8941_gpios>;
+		interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
+
+		pinctrl-0 = <&fuelgauge_pin>;
+		pinctrl-names = "default";
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&pm8941_gpios {
+	gpio_keys_pin_a: gpio-keys-active-state {
+		pins = "gpio2", "gpio3", "gpio5";
+		function = "normal";
+		bias-pull-up;
+		power-source = <PM8941_GPIO_S3>;
+	};
+
+	fuelgauge_pin: fuelgauge-int-state {
+		pins = "gpio26";
+		function = "normal";
+		bias-disable;
+		input-enable;
+		power-source = <PM8941_GPIO_S3>;
+	};
+
+	touch_pin: touchscreen-int-state {
+		pins = "gpio30";
+		function = "normal";
+		bias-disable;
+		input-enable;
+		power-source = <PM8941_GPIO_S3>;
+	};
+
+	touch_ldo_pin: touchscreen-ldo-state {
+		pins = "gpio9";
+		function = "normal";
+		output-high;
+		power-source = <PM8941_GPIO_S3>;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>;
+	};
+
+	touchkey_pin: touchkey-int-state {
+		pins = "gpio29";
+		function = "normal";
+		bias-disable;
+		input-enable;
+		power-source = <PM8941_GPIO_S3>;
+	};
+};
+
+&remoteproc_adsp {
+	cx-supply = <&pm8841_s2>;
+	status = "okay";
+};
+
+&remoteproc_mss {
+	cx-supply = <&pm8841_s2>;
+	mss-supply = <&pm8841_s3>;
+	mx-supply = <&pm8841_s1>;
+	pll-supply = <&pm8941_l12>;
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pm8841-regulators";
+
+		pm8841_s1: s1 {
+			regulator-min-microvolt = <675000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s2: s2 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s3: s3 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s4: s4 {
+			regulator-min-microvolt = <815000>;
+			regulator-max-microvolt = <900000>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,rpm-pm8941-regulators";
+
+		pm8941_s1: s1 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-always-on;
+		};
+
+		pm8941_s2: s2 {
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+		};
+
+		pm8941_s3: s3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l1: l1 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l3: l3 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l4: l4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l11: l11 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8941_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		pm8941_l13: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8941_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l15: l15 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8941_l16: l16 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l17: l17 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8941_l18: l18 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l19: l19 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <3350000>;
+		};
+
+		pm8941_l20: l20 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+		};
+
+		pm8941_l21: l21 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+		};
+
+		pm8941_l22: l22 {
+			regulator-min-microvolt = <2500000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8941_l23: l23 {
+			regulator-min-microvolt = <2400000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8941_l24: l24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+
+		pm8941_lvs1: lvs1 {};
+		pm8941_lvs3: lvs3 {};
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&pm8941_l20>;
+	vqmmc-supply = <&pm8941_s3>;
+
+	pinctrl-0 = <&sdhc1_pin_a>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&sdhc_3 {
+	max-frequency = <100000000>;
+
+	vmmc-supply = <&pm8941_l21>;
+	vqmmc-supply = <&pm8941_l21>;
+
+	pinctrl-0 = <&sdhc3_pin_a>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&tlmm {
+	sdhc1_pin_a: sdhc1-pin-active-state {
+		clk-pins {
+			pins = "sdc1_clk";
+			drive-strength = <4>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc1_cmd", "sdc1_data";
+			drive-strength = <4>;
+			bias-pull-up;
+		};
+	};
+
+	sdhc3_pin_a: sdhc3-pin-active-state {
+		pins = "gpio35", "gpio36", "gpio37", "gpio38", "gpio39", "gpio40";
+		function = "sdc3";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	i2c_touchkey_pins: i2c-touchkey-state {
+		pins = "gpio95", "gpio96";
+		function = "gpio";
+		bias-pull-up;
+	};
+};
+
+&usb {
+	phys = <&usb_hs1_phy>;
+	phy-select = <&tcsr 0xb000 0>;
+
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+
+	status = "okay";
+};
+
+&usb_hs1_phy {
+	v1p8-supply = <&pm8941_l6>;
+	v3p3-supply = <&pm8941_l24>;
+
+	qcom,init-seq = /bits/ 8 <0x1 0x64>;
+
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine-amami.dts b/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine-amami.dts
new file mode 100644
index 000000000000..472a45408add
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine-amami.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974-sony-xperia-rhine.dtsi"
+
+/ {
+	model = "Sony Xperia Z1 Compact";
+	compatible = "sony,xperia-amami", "qcom,msm8974";
+	chassis-type = "handset";
+
+	gpio-keys {
+		key-camera-snapshot {
+			label = "camera_snapshot";
+			gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_CAMERA>;
+		};
+
+		key-camera-focus {
+			label = "camera_focus";
+			gpios = <&pm8941_gpios 4 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_CAMERA_FOCUS>;
+		};
+	};
+};
+
+&smbb {
+	qcom,fast-charge-safe-current = <1300000>;
+	qcom,fast-charge-current-limit = <1300000>;
+	qcom,dc-current-limit = <1300000>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine-honami.dts b/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine-honami.dts
new file mode 100644
index 000000000000..c3d69641fc1d
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine-honami.dts
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974-sony-xperia-rhine.dtsi"
+
+/ {
+	model = "Sony Xperia Z1";
+	compatible = "sony,xperia-honami", "qcom,msm8974";
+	chassis-type = "handset";
+
+	gpio-keys {
+		key-camera-snapshot {
+			label = "camera_snapshot";
+			gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_CAMERA>;
+		};
+
+		key-camera-focus {
+			label = "camera_focus";
+			gpios = <&pm8941_gpios 4 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_CAMERA_FOCUS>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine-togari.dts b/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine-togari.dts
new file mode 100644
index 000000000000..f60f7304d35e
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine-togari.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974-sony-xperia-rhine.dtsi"
+
+/* Togari uses a different touchscreen compared to other rhine devices */
+/delete-node/ &touchscreen;
+
+/ {
+	model = "Sony Xperia Z Ultra";
+	compatible = "sony,xperia-togari", "qcom,msm8974";
+	chassis-type = "handset";
+};
+
+&pm8941_l23 {
+	regulator-min-microvolt = <2600000>;
+	regulator-max-microvolt = <2600000>;
+};
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine.dtsi
new file mode 100644
index 000000000000..d7322fc6a095
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974-sony-xperia-rhine.dtsi
@@ -0,0 +1,516 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974.dtsi"
+#include "pm8841.dtsi"
+#include "pm8941.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+	aliases {
+		mmc0 = &sdhc_1;
+		mmc1 = &sdhc_2;
+		serial0 = &blsp1_uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pin_a>;
+
+		key-volume-down {
+			label = "volume_down";
+			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+
+		key-volume-up {
+			label = "volume_up";
+			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		ramoops@3e8e0000 {
+			compatible = "ramoops";
+			reg = <0x3e8e0000 0x200000>;
+
+			console-size = <0x100000>;
+			record-size = <0x10000>;
+			ftrace-size = <0x10000>;
+			pmsg-size = <0x80000>;
+		};
+	};
+
+	vreg_boost: vreg-boost {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vreg-boost";
+		regulator-min-microvolt = <3150000>;
+		regulator-max-microvolt = <3150000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		gpio = <&pm8941_gpios 21 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&boost_bypass_n_pin>;
+	};
+
+	vreg_vph_pwr: vreg-vph-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "vph-pwr";
+
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+
+		regulator-always-on;
+	};
+};
+
+&blsp1_i2c2 {
+	status = "okay";
+	clock-frequency = <355000>;
+
+	touchscreen: synaptics@2c {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x2c>;
+
+		interrupts-extended = <&tlmm 61 IRQ_TYPE_EDGE_FALLING>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		vdd-supply = <&pm8941_l22>;
+		vio-supply = <&pm8941_lvs3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_pin>;
+
+		syna,startup-delay-ms = <10>;
+
+		rmi4-f01@1 {
+			reg = <0x1>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f11@11 {
+			reg = <0x11>;
+			touchscreen-inverted-x;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp1_i2c6 {
+	status = "okay";
+	clock-frequency = <355000>;
+
+	nfc@28 {
+		compatible = "nxp,pn544-i2c";
+		reg = <0x28>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <59 IRQ_TYPE_EDGE_RISING>;
+
+		enable-gpios = <&pm8941_gpios 23 GPIO_ACTIVE_HIGH>;
+		firmware-gpios = <&tlmm 77 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&blsp2_dma {
+	qcom,controlled-remotely;
+};
+
+&blsp2_i2c5 {
+	status = "okay";
+	clock-frequency = <355000>;
+
+	/* sii8334 MHL HDMI bridge */
+};
+
+&pm8941_coincell {
+	status = "okay";
+	qcom,rset-ohms = <2100>;
+	qcom,vset-millivolts = <3000>;
+};
+
+&pm8941_gpios {
+	gpio_keys_pin_a: gpio-keys-active-state {
+		pins = "gpio2", "gpio3", "gpio4", "gpio5";
+		function = "normal";
+
+		bias-pull-up;
+		power-source = <PM8941_GPIO_S3>;
+	};
+};
+
+&pm8941_lpg {
+	status = "okay";
+
+	qcom,power-source = <1>;
+
+	multi-led {
+		color = <LED_COLOR_ID_RGB>;
+		function = LED_FUNCTION_STATUS;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@5 {
+			reg = <5>;
+			color = <LED_COLOR_ID_BLUE>;
+		};
+
+		led@6 {
+			reg = <6>;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+
+		led@7 {
+			reg = <7>;
+			color = <LED_COLOR_ID_RED>;
+		};
+	};
+};
+
+&pm8941_wled {
+	status = "okay";
+
+	qcom,cs-out;
+	qcom,current-limit = <20>;
+	qcom,current-boost-limit = <805>;
+	qcom,switching-freq = <1600>;
+	qcom,ovp = <29>;
+	qcom,num-strings = <2>;
+};
+
+&remoteproc_adsp {
+	cx-supply = <&pm8841_s2>;
+	status = "okay";
+};
+
+&remoteproc_mss {
+	cx-supply = <&pm8841_s2>;
+	mss-supply = <&pm8841_s3>;
+	mx-supply = <&pm8841_s1>;
+	pll-supply = <&pm8941_l12>;
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pm8841-regulators";
+
+		pm8841_s1: s1 {
+			regulator-min-microvolt = <675000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s2: s2 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s3: s3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s4: s4 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,rpm-pm8941-regulators";
+
+		vdd_l1_l3-supply = <&pm8941_s1>;
+		vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+		vdd_l4_l11-supply = <&pm8941_s1>;
+		vdd_l5_l7-supply = <&pm8941_s2>;
+		vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+		vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+		vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+		vdd_l21-supply = <&vreg_boost>;
+
+		pm8941_s1: s1 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_s2: s2 {
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+			regulator-boot-on;
+		};
+
+		pm8941_s3: s3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_s4: s4 {
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+		};
+
+		pm8941_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l3: l3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l4: l4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l11: l11 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8941_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l13: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l15: l15 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8941_l16: l16 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l17: l17 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l18: l18 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l19: l19 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8941_l20: l20 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+			regulator-boot-on;
+		};
+
+		pm8941_l21: l21 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l22: l22 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8941_l23: l23 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+
+		pm8941_l24: l24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			regulator-boot-on;
+		};
+
+		pm8941_lvs3: lvs3 {};
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	vmmc-supply = <&pm8941_l20>;
+	vqmmc-supply = <&pm8941_s3>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	vmmc-supply = <&pm8941_l21>;
+	vqmmc-supply = <&pm8941_l13>;
+
+	cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_on>;
+	pinctrl-1 = <&sdc2_off>;
+};
+
+&smbb {
+	usb-charge-current-limit = <1800000>;
+
+	qcom,fast-charge-safe-current = <1500000>;
+	qcom,fast-charge-current-limit = <1500000>;
+	qcom,dc-current-limit = <1800000>;
+	qcom,fast-charge-safe-voltage = <4400000>;
+	qcom,fast-charge-high-threshold-voltage = <4350000>;
+	qcom,fast-charge-low-threshold-voltage = <3400000>;
+	qcom,auto-recharge-threshold-voltage = <4200000>;
+	qcom,minimum-input-voltage = <4300000>;
+
+	status = "okay";
+};
+
+&tlmm {
+	ts_int_pin: touch-int-state {
+		pins = "gpio61";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	sdc1_on: sdc1-on-state {
+		clk-pins {
+			pins = "sdc1_clk";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc1_cmd", "sdc1_data";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	sdc2_on: sdc-on-state {
+		clk-pins {
+			pins = "sdc2_clk";
+			drive-strength = <10>;
+			bias-disable;
+		};
+
+		cmd-data-pins {
+			pins = "sdc2_cmd", "sdc2_data";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+
+		cd-pins {
+			pins = "gpio62";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+};
+
+&usb {
+	status = "okay";
+
+	phys = <&usb_hs1_phy>;
+	phy-select = <&tcsr 0xb000 0>;
+	extcon = <&smbb>, <&usb_id>;
+	vbus-supply = <&chg_otg>;
+
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+};
+
+&usb_hs1_phy {
+	status = "okay";
+
+	v1p8-supply = <&pm8941_l6>;
+	v3p3-supply = <&pm8941_l24>;
+
+	extcon = <&smbb>;
+	qcom,init-seq = /bits/ 8 <0x1 0x64>;
+};
diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi
index 412d94736c35..7e119370f337 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-msm8974.dtsi
@@ -3,6 +3,7 @@
 
 #include <dt-bindings/interconnect/qcom,msm8974.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,dsi-phy-28nm.h>
 #include <dt-bindings/clock/qcom,gcc-msm8974.h>
 #include <dt-bindings/clock/qcom,mmcc-msm8974.h>
 #include <dt-bindings/clock/qcom,rpmcc.h>
@@ -12,121 +13,82 @@
 / {
 	#address-cells = <1>;
 	#size-cells = <1>;
-	model = "Qualcomm MSM8974";
-	compatible = "qcom,msm8974";
 	interrupt-parent = <&intc>;
 
-	reserved-memory {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		mpss_region: mpss@8000000 {
-			reg = <0x08000000 0x5100000>;
-			no-map;
-		};
-
-		mba_region: mba@d100000 {
-			reg = <0x0d100000 0x100000>;
-			no-map;
-		};
-
-		wcnss_region: wcnss@d200000 {
-			reg = <0x0d200000 0xa00000>;
-			no-map;
-		};
-
-		adsp_region: adsp@dc00000 {
-			reg = <0x0dc00000 0x1900000>;
-			no-map;
-		};
+	chosen { };
 
-		venus@f500000 {
-			reg = <0x0f500000 0x500000>;
-			no-map;
-		};
-
-		smem_region: smem@fa00000 {
-			reg = <0xfa00000 0x200000>;
-			no-map;
-		};
-
-		tz@fc00000 {
-			reg = <0x0fc00000 0x160000>;
-			no-map;
-		};
-
-		rfsa@fd60000 {
-			reg = <0x0fd60000 0x20000>;
-			no-map;
+	clocks {
+		xo_board: xo_board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <19200000>;
 		};
 
-		rmtfs@fd80000 {
-			compatible = "qcom,rmtfs-mem";
-			reg = <0x0fd80000 0x180000>;
-			no-map;
-
-			qcom,client-id = <1>;
+		sleep_clk: sleep_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
 		};
 	};
 
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
-		interrupts = <GIC_PPI 9 0xf04>;
+		interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
 
-		CPU0: cpu@0 {
+		cpu0: cpu@0 {
 			compatible = "qcom,krait";
 			enable-method = "qcom,kpss-acc-v2";
 			device_type = "cpu";
 			reg = <0>;
-			next-level-cache = <&L2>;
+			next-level-cache = <&l2>;
 			qcom,acc = <&acc0>;
 			qcom,saw = <&saw0>;
-			cpu-idle-states = <&CPU_SPC>;
+			cpu-idle-states = <&cpu_spc>;
 		};
 
-		CPU1: cpu@1 {
+		cpu1: cpu@1 {
 			compatible = "qcom,krait";
 			enable-method = "qcom,kpss-acc-v2";
 			device_type = "cpu";
 			reg = <1>;
-			next-level-cache = <&L2>;
+			next-level-cache = <&l2>;
 			qcom,acc = <&acc1>;
 			qcom,saw = <&saw1>;
-			cpu-idle-states = <&CPU_SPC>;
+			cpu-idle-states = <&cpu_spc>;
 		};
 
-		CPU2: cpu@2 {
+		cpu2: cpu@2 {
 			compatible = "qcom,krait";
 			enable-method = "qcom,kpss-acc-v2";
 			device_type = "cpu";
 			reg = <2>;
-			next-level-cache = <&L2>;
+			next-level-cache = <&l2>;
 			qcom,acc = <&acc2>;
 			qcom,saw = <&saw2>;
-			cpu-idle-states = <&CPU_SPC>;
+			cpu-idle-states = <&cpu_spc>;
 		};
 
-		CPU3: cpu@3 {
+		cpu3: cpu@3 {
 			compatible = "qcom,krait";
 			enable-method = "qcom,kpss-acc-v2";
 			device_type = "cpu";
 			reg = <3>;
-			next-level-cache = <&L2>;
+			next-level-cache = <&l2>;
 			qcom,acc = <&acc3>;
 			qcom,saw = <&saw3>;
-			cpu-idle-states = <&CPU_SPC>;
+			cpu-idle-states = <&cpu_spc>;
 		};
 
-		L2: l2-cache {
+		l2: l2-cache {
 			compatible = "cache";
 			cache-level = <2>;
+			cache-unified;
 			qcom,saw = <&saw_l2>;
 		};
 
 		idle-states {
-			CPU_SPC: spc {
+			cpu_spc: cpu-spc {
 				compatible = "qcom,idle-state-spc",
 						"arm,idle-state";
 				entry-latency-us = <150>;
@@ -136,238 +98,109 @@
 		};
 	};
 
-	memory {
+	firmware {
+		scm {
+			compatible = "qcom,scm-msm8974", "qcom,scm";
+			clocks = <&gcc GCC_CE1_CLK>, <&gcc GCC_CE1_AXI_CLK>, <&gcc GCC_CE1_AHB_CLK>;
+			clock-names = "core", "bus", "iface";
+		};
+	};
+
+	memory@0 {
 		device_type = "memory";
 		reg = <0x0 0x0>;
 	};
 
-	thermal-zones {
-		cpu0-thermal {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&tsens 5>;
-
-			trips {
-				cpu_alert0: trip0 {
-					temperature = <75000>;
-					hysteresis = <2000>;
-					type = "passive";
-				};
-				cpu_crit0: trip1 {
-					temperature = <110000>;
-					hysteresis = <2000>;
-					type = "critical";
-				};
-			};
-		};
-
-		cpu1-thermal {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&tsens 6>;
-
-			trips {
-				cpu_alert1: trip0 {
-					temperature = <75000>;
-					hysteresis = <2000>;
-					type = "passive";
-				};
-				cpu_crit1: trip1 {
-					temperature = <110000>;
-					hysteresis = <2000>;
-					type = "critical";
-				};
-			};
-		};
-
-		cpu2-thermal {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
+	pmu {
+		compatible = "qcom,krait-pmu";
+		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+	};
 
-			thermal-sensors = <&tsens 7>;
+	rpm: remoteproc {
+		compatible = "qcom,msm8974-rpm-proc", "qcom,rpm-proc";
 
-			trips {
-				cpu_alert2: trip0 {
-					temperature = <75000>;
-					hysteresis = <2000>;
-					type = "passive";
-				};
-				cpu_crit2: trip1 {
-					temperature = <110000>;
-					hysteresis = <2000>;
-					type = "critical";
-				};
-			};
+		master-stats {
+			compatible = "qcom,rpm-master-stats";
+			qcom,rpm-msg-ram = <&apss_master_stats>,
+					   <&mpss_master_stats>,
+					   <&lpss_master_stats>,
+					   <&pronto_master_stats>;
+			qcom,master-names = "APSS",
+					    "MPSS",
+					    "LPSS",
+					    "PRONTO";
 		};
 
-		cpu3-thermal {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
+		smd-edge {
+			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
+			mboxes = <&apcs 0>;
+			qcom,smd-edge = <15>;
 
-			thermal-sensors = <&tsens 8>;
+			rpm_requests: rpm-requests {
+				compatible = "qcom,rpm-msm8974", "qcom,smd-rpm";
+				qcom,smd-channels = "rpm_requests";
 
-			trips {
-				cpu_alert3: trip0 {
-					temperature = <75000>;
-					hysteresis = <2000>;
-					type = "passive";
-				};
-				cpu_crit3: trip1 {
-					temperature = <110000>;
-					hysteresis = <2000>;
-					type = "critical";
+				rpmcc: clock-controller {
+					compatible = "qcom,rpmcc-msm8974", "qcom,rpmcc";
+					#clock-cells = <1>;
+					clocks = <&xo_board>;
+					clock-names = "xo";
 				};
 			};
 		};
+	};
 
-		q6-dsp-thermal {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&tsens 1>;
+	reserved_memory: reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
 
-			trips {
-				q6_dsp_alert0: trip-point0 {
-					temperature = <90000>;
-					hysteresis = <2000>;
-					type = "hot";
-				};
-			};
+		mpss_region: mpss@8000000 {
+			reg = <0x08000000 0x5100000>;
+			no-map;
 		};
 
-		modemtx-thermal {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&tsens 2>;
-
-			trips {
-				modemtx_alert0: trip-point0 {
-					temperature = <90000>;
-					hysteresis = <2000>;
-					type = "hot";
-				};
-			};
+		mba_region: mba@d100000 {
+			reg = <0x0d100000 0x100000>;
+			no-map;
 		};
 
-		video-thermal {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&tsens 3>;
-
-			trips {
-				video_alert0: trip-point0 {
-					temperature = <95000>;
-					hysteresis = <2000>;
-					type = "hot";
-				};
-			};
+		wcnss_region: wcnss@d200000 {
+			reg = <0x0d200000 0xa00000>;
+			no-map;
 		};
 
-		wlan-thermal {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&tsens 4>;
-
-			trips {
-				wlan_alert0: trip-point0 {
-					temperature = <105000>;
-					hysteresis = <2000>;
-					type = "hot";
-				};
-			};
+		adsp_region: adsp@dc00000 {
+			reg = <0x0dc00000 0x1900000>;
+			no-map;
 		};
 
-		gpu-top-thermal {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&tsens 9>;
-
-			trips {
-				gpu1_alert0: trip-point0 {
-					temperature = <90000>;
-					hysteresis = <2000>;
-					type = "hot";
-				};
-			};
+		venus_region: memory@f500000 {
+			reg = <0x0f500000 0x500000>;
+			no-map;
 		};
 
-		gpu-bottom-thermal {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&tsens 10>;
-
-			trips {
-				gpu2_alert0: trip-point0 {
-					temperature = <90000>;
-					hysteresis = <2000>;
-					type = "hot";
-				};
-			};
+		smem_region: smem@fa00000 {
+			reg = <0xfa00000 0x200000>;
+			no-map;
 		};
-	};
-
-	cpu-pmu {
-		compatible = "qcom,krait-pmu";
-		interrupts = <GIC_PPI 7 0xf04>;
-	};
 
-	clocks {
-		xo_board: xo_board {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <19200000>;
+		tz_region: memory@fc00000 {
+			reg = <0x0fc00000 0x160000>;
+			no-map;
 		};
 
-		sleep_clk: sleep_clk {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
+		rfsa_mem: memory@fd60000 {
+			reg = <0x0fd60000 0x20000>;
+			no-map;
 		};
-	};
-
-	timer {
-		compatible = "arm,armv7-timer";
-		interrupts = <GIC_PPI 2 0xf08>,
-			     <GIC_PPI 3 0xf08>,
-			     <GIC_PPI 4 0xf08>,
-			     <GIC_PPI 1 0xf08>;
-		clock-frequency = <19200000>;
-	};
-
-	adsp-pil {
-		compatible = "qcom,msm8974-adsp-pil";
-
-		interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_EDGE_RISING>,
-				      <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
-				      <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
-				      <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
-				      <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
-		interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
-
-		cx-supply = <&pm8841_s2>;
-
-		clocks = <&xo_board>;
-		clock-names = "xo";
 
-		memory-region = <&adsp_region>;
-
-		qcom,smem-states = <&adsp_smp2p_out 0>;
-		qcom,smem-state-names = "stop";
-
-		smd-edge {
-			interrupts = <GIC_SPI 156 IRQ_TYPE_EDGE_RISING>;
-
-			qcom,ipc = <&apcs 8 8>;
-			qcom,smd-edge = <1>;
+		rmtfs@fd80000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0x0fd80000 0x180000>;
+			no-map;
 
-			label = "lpass";
+			qcom,client-id = <1>;
 		};
 	};
 
@@ -387,7 +220,7 @@
 		interrupt-parent = <&intc>;
 		interrupts = <GIC_SPI 158 IRQ_TYPE_EDGE_RISING>;
 
-		qcom,ipc = <&apcs 8 10>;
+		mboxes = <&apcs 10>;
 
 		qcom,local-pid = <0>;
 		qcom,remote-pid = <2>;
@@ -412,7 +245,7 @@
 		interrupt-parent = <&intc>;
 		interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>;
 
-		qcom,ipc = <&apcs 8 14>;
+		mboxes = <&apcs 14>;
 
 		qcom,local-pid = <0>;
 		qcom,remote-pid = <1>;
@@ -437,7 +270,7 @@
 		interrupt-parent = <&intc>;
 		interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>;
 
-		qcom,ipc = <&apcs 8 18>;
+		mboxes = <&apcs 18>;
 
 		qcom,local-pid = <0>;
 		qcom,remote-pid = <4>;
@@ -462,9 +295,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		qcom,ipc-1 = <&apcs 8 13>;
-		qcom,ipc-2 = <&apcs 8 9>;
-		qcom,ipc-3 = <&apcs 8 19>;
+		mboxes = <0>, <&apcs 13>, <&apcs 9>, <&apcs 19>;
 
 		apps_smsm: apps@0 {
 			reg = <0>;
@@ -497,14 +328,6 @@
 		};
 	};
 
-	firmware {
-		scm {
-			compatible = "qcom,scm";
-			clocks = <&gcc GCC_CE1_CLK>, <&gcc GCC_CE1_AXI_CLK>, <&gcc GCC_CE1_AHB_CLK>;
-			clock-names = "core", "bus", "iface";
-		};
-	};
-
 	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -519,34 +342,24 @@
 			      <0xf9002000 0x1000>;
 		};
 
-		apcs: syscon@f9011000 {
-			compatible = "syscon";
+		apcs: mailbox@f9011000 {
+			compatible = "qcom,msm8974-apcs-kpss-global",
+				     "qcom,msm8994-apcs-kpss-global", "syscon";
 			reg = <0xf9011000 0x1000>;
+			#mbox-cells = <1>;
 		};
 
-		qfprom: qfprom@fc4bc000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "qcom,qfprom";
-			reg = <0xfc4bc000 0x1000>;
-			tsens_calib: calib@d0 {
-				reg = <0xd0 0x18>;
-			};
-			tsens_backup: backup@440 {
-				reg = <0x440 0x10>;
-			};
+		saw_l2: power-manager@f9012000 {
+			compatible = "qcom,msm8974-saw2-v2.1-l2", "qcom,saw2";
+			reg = <0xf9012000 0x1000>;
 		};
 
-		tsens: thermal-sensor@fc4a9000 {
-			compatible = "qcom,msm8974-tsens";
-			reg = <0xfc4a9000 0x1000>, /* TM */
-			      <0xfc4a8000 0x1000>; /* SROT */
-			nvmem-cells = <&tsens_calib>, <&tsens_backup>;
-			nvmem-cell-names = "calib", "calib_backup";
-			#qcom,sensors = <11>;
-			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "uplow";
-			#thermal-sensor-cells = <1>;
+		watchdog@f9017000 {
+			compatible = "qcom,apss-wdt-msm8974", "qcom,kpss-wdt";
+			reg = <0xf9017000 0x1000>;
+			interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 4 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&sleep_clk>;
 		};
 
 		timer@f9020000 {
@@ -608,93 +421,99 @@
 			};
 		};
 
-		saw0: power-controller@f9089000 {
-			compatible = "qcom,msm8974-saw2-v2.1-cpu", "qcom,saw2";
-			reg = <0xf9089000 0x1000>, <0xf9009000 0x1000>;
+		acc0: power-manager@f9088000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0xf9088000 0x1000>, <0xf9008000 0x1000>;
 		};
 
-		saw1: power-controller@f9099000 {
+		saw0: power-manager@f9089000 {
 			compatible = "qcom,msm8974-saw2-v2.1-cpu", "qcom,saw2";
-			reg = <0xf9099000 0x1000>, <0xf9009000 0x1000>;
+			reg = <0xf9089000 0x1000>, <0xf9009000 0x1000>;
 		};
 
-		saw2: power-controller@f90a9000 {
-			compatible = "qcom,msm8974-saw2-v2.1-cpu", "qcom,saw2";
-			reg = <0xf90a9000 0x1000>, <0xf9009000 0x1000>;
+		acc1: power-manager@f9098000 {
+			compatible = "qcom,kpss-acc-v2";
+			reg = <0xf9098000 0x1000>, <0xf9008000 0x1000>;
 		};
 
-		saw3: power-controller@f90b9000 {
+		saw1: power-manager@f9099000 {
 			compatible = "qcom,msm8974-saw2-v2.1-cpu", "qcom,saw2";
-			reg = <0xf90b9000 0x1000>, <0xf9009000 0x1000>;
-		};
-
-		saw_l2: power-controller@f9012000 {
-			compatible = "qcom,saw2";
-			reg = <0xf9012000 0x1000>;
-			regulator;
-		};
-
-		acc0: clock-controller@f9088000 {
-			compatible = "qcom,kpss-acc-v2";
-			reg = <0xf9088000 0x1000>, <0xf9008000 0x1000>;
+			reg = <0xf9099000 0x1000>, <0xf9009000 0x1000>;
 		};
 
-		acc1: clock-controller@f9098000 {
+		acc2: power-manager@f90a8000 {
 			compatible = "qcom,kpss-acc-v2";
-			reg = <0xf9098000 0x1000>, <0xf9008000 0x1000>;
+			reg = <0xf90a8000 0x1000>, <0xf9008000 0x1000>;
 		};
 
-		acc2: clock-controller@f90a8000 {
-			compatible = "qcom,kpss-acc-v2";
-			reg = <0xf90a8000 0x1000>, <0xf9008000 0x1000>;
+		saw2: power-manager@f90a9000 {
+			compatible = "qcom,msm8974-saw2-v2.1-cpu", "qcom,saw2";
+			reg = <0xf90a9000 0x1000>, <0xf9009000 0x1000>;
 		};
 
-		acc3: clock-controller@f90b8000 {
+		acc3: power-manager@f90b8000 {
 			compatible = "qcom,kpss-acc-v2";
 			reg = <0xf90b8000 0x1000>, <0xf9008000 0x1000>;
 		};
 
-		restart@fc4ab000 {
-			compatible = "qcom,pshold";
-			reg = <0xfc4ab000 0x4>;
+		saw3: power-manager@f90b9000 {
+			compatible = "qcom,msm8974-saw2-v2.1-cpu", "qcom,saw2";
+			reg = <0xf90b9000 0x1000>, <0xf9009000 0x1000>;
 		};
 
-		gcc: clock-controller@fc400000 {
-			compatible = "qcom,gcc-msm8974";
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-			#power-domain-cells = <1>;
-			reg = <0xfc400000 0x4000>;
-		};
+		sdhc_1: mmc@f9824900 {
+			compatible = "qcom,msm8974-sdhci", "qcom,sdhci-msm-v4";
+			reg = <0xf9824900 0x11c>, <0xf9824000 0x800>;
+			reg-names = "hc", "core";
+			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
+				 <&xo_board>;
+			clock-names = "iface", "core", "xo";
+			bus-width = <8>;
+			non-removable;
 
-		tcsr: syscon@fd4a0000 {
-			compatible = "syscon";
-			reg = <0xfd4a0000 0x10000>;
+			status = "disabled";
 		};
 
-		tcsr_mutex_block: syscon@fd484000 {
-			compatible = "syscon";
-			reg = <0xfd484000 0x2000>;
-		};
+		sdhc_3: mmc@f9864900 {
+			compatible = "qcom,msm8974-sdhci", "qcom,sdhci-msm-v4";
+			reg = <0xf9864900 0x11c>, <0xf9864000 0x800>;
+			reg-names = "hc", "core";
+			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC3_AHB_CLK>,
+				 <&gcc GCC_SDCC3_APPS_CLK>,
+				 <&xo_board>;
+			clock-names = "iface", "core", "xo";
+			bus-width = <4>;
 
-		mmcc: clock-controller@fd8c0000 {
-			compatible = "qcom,mmcc-msm8974";
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-			#power-domain-cells = <1>;
-			reg = <0xfd8c0000 0x6000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
 		};
 
-		tcsr_mutex: tcsr-mutex {
-			compatible = "qcom,tcsr-mutex";
-			syscon = <&tcsr_mutex_block 0 0x80>;
+		sdhc_2: mmc@f98a4900 {
+			compatible = "qcom,msm8974-sdhci", "qcom,sdhci-msm-v4";
+			reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>;
+			reg-names = "hc", "core";
+			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>,
+				 <&xo_board>;
+			clock-names = "iface", "core", "xo";
+			bus-width = <4>;
 
-			#hwlock-cells = <1>;
-		};
+			#address-cells = <1>;
+			#size-cells = <0>;
 
-		rpm_msg_ram: memory@fc428000 {
-			compatible = "qcom,rpm-msg-ram";
-			reg = <0xfc428000 0x4000>;
+			status = "disabled";
 		};
 
 		blsp1_uart1: serial@f991d000 {
@@ -712,19 +531,90 @@
 			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
 			clock-names = "core", "iface";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_uart2_default>;
 			status = "disabled";
 		};
 
-		blsp2_uart7: serial@f995d000 {
+		blsp1_i2c1: i2c@f9923000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9923000 0x1000>;
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp1_i2c1_default>;
+			pinctrl-1 = <&blsp1_i2c1_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c2: i2c@f9924000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9924000 0x1000>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp1_i2c2_default>;
+			pinctrl-1 = <&blsp1_i2c2_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c3: i2c@f9925000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9925000 0x1000>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp1_i2c3_default>;
+			pinctrl-1 = <&blsp1_i2c3_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c6: i2c@f9928000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9928000 0x1000>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp1_i2c6_default>;
+			pinctrl-1 = <&blsp1_i2c6_sleep>;
+			#address-cells = <1>;