| Age | Commit message (Collapse) | Author |
|---|
|
The vdd3p0 LDO's input should be from external USB VBUS directly, NOT
PMIC's power supply, the vdd3p0 LDO's target output voltage can be
controlled by SW, and it requires input voltage to be high enough, with
incorrect power supply assigned, if the power supply's voltage is lower
than the LDO target output voltage, it will return fail and skip the LDO
voltage adjustment, so remove the power supply assignment for vdd3p0 to
avoid such scenario.
Fixes: 96a9169cf621 ("ARM: dts: imx6sll-evk: Assign corresponding power supply for vdd3p0")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The SNVS poweroff depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up to external PMIC.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On i.MX6SLL EVK board, sw2 supplies vdd3p0 LDO, this patch assigns
corresponding power supply for vdd3p0 to avoid confusion by below log:
vdd3p0: supplied by regulator-dummy
With this patch, the power supply is more accurate:
vdd3p0: supplied by SW2
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Most of the legacy "gpio-key,wakeup" and "enable-sdio-wakeup" boolean
properties are already replaced with "wakeup-source". However few
occurrences of old property has popped up again, probably from the
remnants in downstream trees. Almost all of those were remove couple
of years back.
Replace the legacy properties with the unified "wakeup-source" property
introduced in the commit 700a38b27eef ("Input: gpio_keys - switch to using
generic device properties") and commit 0dbcdc0622ea ("mmc: core: enable
support for the standard "wakeup-source" property")
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
i.MX6SLL EVK board has WDOG_B pin connected to the PMIC;
Add the WDOG_B pinctrl entry and 'fsl,ext-reset-output'
property to wdog node to let watchdog trigger a system
POR reset via the PMIC.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On i.MX6SLL EVK board, there is a debug LED controlled
by MX6SLL_PAD_EPDC_VCOM1__GPIO2_IO04 pin, add support
for it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Boards based on imx6sl have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx6sl.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On i.MX6SLL EVK board, pfuze100 sw4 supplies
LPDDR3 which is critical for system, must be
always on.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable SEIKO 43WVF1G lcdif panel for DRM driver,
add necessary properties according to SEIKO 43WVF1G
driver's requirement, such as "dvdd-supply", "avdd-supply"
and "backlight" etc..
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On i.MX6SLL EVK board, lcd regulator is controlled
by GPIO4 IO03 using MX6SLL_PAD_KEY_ROW5__GPIO4_IO03 pin,
NOT MX6SLL_PAD_ECSPI1_SCLK__GPIO4_IO08, correct it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable pwm1 module on i.MX6SLL EVK board to make
backlight driver really work with LCD panel connected.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On i.MX6SLL EVK board, SD3 slot can be used for
WiFi and other SD accessories, enable it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This makes it possible to enable earlycon for debugging by just passing
an empty "earlycon" argument on the kernel command-line.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add dts file support for imx6sll EVK board.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Dong Aisheng <Aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
