| Age | Commit message (Collapse) | Author |
|---|
|
Move the conditional loading of hardware DR6 with the guest's DR6 value
out of the core .vcpu_run() loop to fix a bug where KVM can load hardware
with a stale vcpu->arch.dr6.
When the guest accesses a DR and host userspace isn't debugging the guest,
KVM disables DR interception and loads the guest's values into hardware on
VM-Enter and saves them on VM-Exit. This allows the guest to access DRs
at will, e.g. so that a sequence of DR accesses to configure a breakpoint
only generates one VM-Exit.
For DR0-DR3, the logic/behavior is identical between VMX and SVM, and also
identical between KVM_DEBUGREG_BP_ENABLED (userspace debugging the guest)
and KVM_DEBUGREG_WONT_EXIT (guest using DRs), and so KVM handles loading
DR0-DR3 in common code, _outside_ of the core kvm_x86_ops.vcpu_run() loop.
But for DR6, the guest's value doesn't need to be loaded into hardware for
KVM_DEBUGREG_BP_ENABLED, and SVM provides a dedicated VMCB field whereas
VMX requires software to manually load the guest value, and so loading the
guest's value into DR6 is handled by {svm,vmx}_vcpu_run(), i.e. is done
_inside_ the core run loop.
Unfortunately, saving the guest values on VM-Exit is initiated by common
x86, again outside of the core run loop. If the guest modifies DR6 (in
hardware, when DR interception is disabled), and then the next VM-Exit is
a fastpath VM-Exit, KVM will reload hardware DR6 with vcpu->arch.dr6 and
clobber the guest's actual value.
The bug shows up primarily with nested VMX because KVM handles the VMX
preemption timer in the fastpath, and the window between hardware DR6
being modified (in guest context) and DR6 being read by guest software is
orders of magnitude larger in a nested setup. E.g. in non-nested, the
VMX preemption timer would need to fire precisely between #DB injection
and the #DB handler's read of DR6, whereas with a KVM-on-KVM setup, the
window where hardware DR6 is "dirty" extends all the way from L1 writing
DR6 to VMRESUME (in L1).
L1's view:
==========
<L1 disables DR interception>
CPU 0/KVM-7289 [023] d.... 2925.640961: kvm_entry: vcpu 0
A: L1 Writes DR6
CPU 0/KVM-7289 [023] d.... 2925.640963: <hack>: Set DRs, DR6 = 0xffff0ff1
B: CPU 0/KVM-7289 [023] d.... 2925.640967: kvm_exit: vcpu 0 reason EXTERNAL_INTERRUPT intr_info 0x800000ec
D: L1 reads DR6, arch.dr6 = 0
CPU 0/KVM-7289 [023] d.... 2925.640969: <hack>: Sync DRs, DR6 = 0xffff0ff0
CPU 0/KVM-7289 [023] d.... 2925.640976: kvm_entry: vcpu 0
L2 reads DR6, L1 disables DR interception
CPU 0/KVM-7289 [023] d.... 2925.640980: kvm_exit: vcpu 0 reason DR_ACCESS info1 0x0000000000000216
CPU 0/KVM-7289 [023] d.... 2925.640983: kvm_entry: vcpu 0
CPU 0/KVM-7289 [023] d.... 2925.640983: <hack>: Set DRs, DR6 = 0xffff0ff0
L2 detects failure
CPU 0/KVM-7289 [023] d.... 2925.640987: kvm_exit: vcpu 0 reason HLT
L1 reads DR6 (confirms failure)
CPU 0/KVM-7289 [023] d.... 2925.640990: <hack>: Sync DRs, DR6 = 0xffff0ff0
L0's view:
==========
L2 reads DR6, arch.dr6 = 0
CPU 23/KVM-5046 [001] d.... 3410.005610: kvm_exit: vcpu 23 reason DR_ACCESS info1 0x0000000000000216
CPU 23/KVM-5046 [001] ..... 3410.005610: kvm_nested_vmexit: vcpu 23 reason DR_ACCESS info1 0x0000000000000216
L2 => L1 nested VM-Exit
CPU 23/KVM-5046 [001] ..... 3410.005610: kvm_nested_vmexit_inject: reason: DR_ACCESS ext_inf1: 0x0000000000000216
CPU 23/KVM-5046 [001] d.... 3410.005610: kvm_entry: vcpu 23
CPU 23/KVM-5046 [001] d.... 3410.005611: kvm_exit: vcpu 23 reason VMREAD
CPU 23/KVM-5046 [001] d.... 3410.005611: kvm_entry: vcpu 23
CPU 23/KVM-5046 [001] d.... 3410.005612: kvm_exit: vcpu 23 reason VMREAD
CPU 23/KVM-5046 [001] d.... 3410.005612: kvm_entry: vcpu 23
L1 writes DR7, L0 disables DR interception
CPU 23/KVM-5046 [001] d.... 3410.005612: kvm_exit: vcpu 23 reason DR_ACCESS info1 0x0000000000000007
CPU 23/KVM-5046 [001] d.... 3410.005613: kvm_entry: vcpu 23
L0 writes DR6 = 0 (arch.dr6)
CPU 23/KVM-5046 [001] d.... 3410.005613: <hack>: Set DRs, DR6 = 0xffff0ff0
A: <L1 writes DR6 = 1, no interception, arch.dr6 is still '0'>
B: CPU 23/KVM-5046 [001] d.... 3410.005614: kvm_exit: vcpu 23 reason PREEMPTION_TIMER
CPU 23/KVM-5046 [001] d.... 3410.005614: kvm_entry: vcpu 23
C: L0 writes DR6 = 0 (arch.dr6)
CPU 23/KVM-5046 [001] d.... 3410.005614: <hack>: Set DRs, DR6 = 0xffff0ff0
L1 => L2 nested VM-Enter
CPU 23/KVM-5046 [001] d.... 3410.005616: kvm_exit: vcpu 23 reason VMRESUME
L0 reads DR6, arch.dr6 = 0
Reported-by: John Stultz <jstultz@google.com>
Closes: https://lkml.kernel.org/r/CANDhNCq5_F3HfFYABqFGCA1bPd_%2BxgNj-iDQhH4tDk%2Bwi8iZZg%40mail.gmail.com
Fixes: 375e28ffc0cf ("KVM: X86: Set host DR6 only on VMX and for KVM_DEBUGREG_WONT_EXIT")
Fixes: d67668e9dd76 ("KVM: x86, SVM: isolate vcpu->arch.dr6 from vmcb->save.dr6")
Cc: stable@vger.kernel.org
Cc: Jim Mattson <jmattson@google.com>
Tested-by: John Stultz <jstultz@google.com>
Link: https://lore.kernel.org/r/20250125011833.3644371-1-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
As part of enabling TDX virtual machines, support support separation of
private/shared EPT into separate roots.
Confidential computing solutions almost invariably have concepts of
private and shared memory, but they may different a lot in the details.
In SEV, for example, the bit is handled more like a permission bit as
far as the page tables are concerned: the private/shared bit is not
included in the physical address.
For TDX, instead, the bit is more like a physical address bit, with
the host mapping private memory in one half of the address space and
shared in another. Furthermore, the two halves are mapped by different
EPT roots and only the shared half is managed by KVM; the private half
(also called Secure EPT in Intel documentation) gets managed by the
privileged TDX Module via SEAMCALLs.
As a result, the operations that actually change the private half of
the EPT are limited and relatively slow compared to reading a PTE. For
this reason the design for KVM is to keep a mirror of the private EPT in
host memory. This allows KVM to quickly walk the EPT and only perform the
slower private EPT operations when it needs to actually modify mid-level
private PTEs.
There are thus three sets of EPT page tables: external, mirror and
direct. In the case of TDX (the only user of this framework) the
first two cover private memory, whereas the third manages shared
memory:
external EPT - Hidden within the TDX module, modified via TDX module
calls.
mirror EPT - Bookkeeping tree used as an optimization by KVM, not
used by the processor.
direct EPT - Normal EPT that maps unencrypted shared memory.
Managed like the EPT of a normal VM.
Modifying external EPT
----------------------
Modifications to the mirrored page tables need to also perform the
same operations to the private page tables, which will be handled via
kvm_x86_ops. Although this prep series does not interact with the TDX
module at all to actually configure the private EPT, it does lay the
ground work for doing this.
In some ways updating the private EPT is as simple as plumbing PTE
modifications through to also call into the TDX module; however, the
locking is more complicated because inserting a single PTE cannot anymore
be done atomically with a single CMPXCHG. For this reason, the existing
FROZEN_SPTE mechanism is used whenever a call to the TDX module updates the
private EPT. FROZEN_SPTE acts basically as a spinlock on a PTE. Besides
protecting operation of KVM, it limits the set of cases in which the
TDX module will encounter contention on its own PTE locks.
Zapping external EPT
--------------------
While the framework tries to be relatively generic, and to be
understandable without knowing TDX much in detail, some requirements of
TDX sometimes leak; for example the private page tables also cannot be
zapped while the range has anything mapped, so the mirrored/private page
tables need to be protected from KVM operations that zap any non-leaf
PTEs, for example kvm_mmu_reset_context() or kvm_mmu_zap_all_fast().
For normal VMs, guest memory is zapped for several reasons: user
memory getting paged out by the guest, memslots getting deleted,
passthrough of devices with non-coherent DMA. Confidential computing
adds to these the conversion of memory between shared and privates. These
operations must not zap any private memory that is in use by the guest.
This is possible because the only zapping that is out of the control
of KVM/userspace is paging out userspace memory, which cannot apply to
guestmemfd operations. Thus a TDX VM will only zap private memory from
memslot deletion and from conversion between private and shared memory
which is triggered by the guest.
To avoid zapping too much memory, enums are introduced so that operations
can choose to target only private or shared memory, and thus only
direct or mirror EPT. For example:
Memslot deletion - Private and shared
MMU notifier based zapping - Shared only
Conversion to shared - Private only
Conversion to private - Shared only
Other cases of zapping will not be supported for KVM, for example
APICv update or non-coherent DMA status update; for the latter, TDX will
simply require that the CPU supports self-snoop and honor guest PAT
unconditionally for shared memory.
|
|
KVM x86 misc changes for 6.14:
- Overhaul KVM's CPUID feature infrastructure to track all vCPU capabilities
instead of just those where KVM needs to manage state and/or explicitly
enable the feature in hardware. Along the way, refactor the code to make
it easier to add features, and to make it more self-documenting how KVM
is handling each feature.
- Rework KVM's handling of VM-Exits during event vectoring; this plugs holes
where KVM unintentionally puts the vCPU into infinite loops in some scenarios
(e.g. if emulation is triggered by the exit), and brings parity between VMX
and SVM.
- Add pending request and interrupt injection information to the kvm_exit and
kvm_entry tracepoints respectively.
- Fix a relatively benign flaw where KVM would end up redoing RDPKRU when
loading guest/host PKRU, due to a refactoring of the kernel helpers that
didn't account for KVM's pre-checking of the need to do WRPKRU.
|
|
Integrate hooks for mirroring page table operations for cases where TDX
will zap PTEs or free page tables.
Like other Coco technologies, TDX has the concept of private and shared
memory. For TDX the private and shared mappings are managed on separate
EPT roots. The private half is managed indirectly though calls into a
protected runtime environment called the TDX module, where the shared half
is managed within KVM in normal page tables.
Since calls into the TDX module are relatively slow, walking private page
tables by making calls into the TDX module would not be efficient. Because
of this, previous changes have taught the TDP MMU to keep a mirror root,
which is separate, unmapped TDP root that private operations can be
directed to. Currently this root is disconnected from the guest. Now add
plumbing to propagate changes to the "external" page tables being
mirrored. Just create the x86_ops for now, leave plumbing the operations
into the TDX module for future patches.
Add two operations for tearing down page tables, one for freeing page
tables (free_external_spt) and one for zapping PTEs (remove_external_spte).
Define them such that remove_external_spte will perform a TLB flush as
well. (in TDX terms "ensure there are no active translations").
TDX MMU support will exclude certain MMU operations, so only plug in the
mirroring x86 ops where they will be needed. For zapping/freeing, only
hook tdp_mmu_iter_set_spte() which is used for mapping and linking PTs.
Don't bother hooking tdp_mmu_set_spte_atomic() as it is only used for
zapping PTEs in operations unsupported by TDX: zapping collapsible PTEs and
kvm_mmu_zap_all_fast().
In previous changes to address races around concurrent populating using
tdp_mmu_set_spte_atomic(), a solution was introduced to temporarily set
FROZEN_SPTE in the mirrored page tables while performing the external
operations. Such a solution is not needed for the tear down paths in TDX
as these will always be performed with the mmu_lock held for write.
Sprinkle some KVM_BUG_ON()s to reflect this.
Signed-off-by: Isaku Yamahata <isaku.yamahata@intel.com>
Co-developed-by: Kai Huang <kai.huang@intel.com>
Signed-off-by: Kai Huang <kai.huang@intel.com>
Co-developed-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Yan Zhao <yan.y.zhao@intel.com>
Co-developed-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Message-ID: <20240718211230.1492011-16-rick.p.edgecombe@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Integrate hooks for mirroring page table operations for cases where TDX
will set PTEs or link page tables.
Like other Coco technologies, TDX has the concept of private and shared
memory. For TDX the private and shared mappings are managed on separate
EPT roots. The private half is managed indirectly through calls into a
protected runtime environment called the TDX module, where the shared half
is managed within KVM in normal page tables.
Since calls into the TDX module are relatively slow, walking private page
tables by making calls into the TDX module would not be efficient. Because
of this, previous changes have taught the TDP MMU to keep a mirror root,
which is separate, unmapped TDP root that private operations can be
directed to. Currently this root is disconnected from any actual guest
mapping. Now add plumbing to propagate changes to the "external" page
tables being mirrored. Just create the x86_ops for now, leave plumbing the
operations into the TDX module for future patches.
Add two operations for setting up external page tables, one for linking
new page tables and one for setting leaf PTEs. Don't add any op for
configuring the root PFN, as TDX handles this itself. Don't provide a
way to set permissions on the PTEs also, as TDX doesn't support it.
This results in MMU "mirroring" support that is very targeted towards TDX.
Since it is likely there will be no other user, the main benefit of making
the support generic is to keep TDX specific *looking* code outside of the
MMU. As a generic feature it will make enough sense from TDX's
perspective. For developers unfamiliar with TDX arch it can express the
general concepts such that they can continue to work in the code.
TDX MMU support will exclude certain MMU operations, so only plug in the
mirroring x86 ops where they will be needed. For setting/linking, only
hook tdp_mmu_set_spte_atomic() which is used for mapping and linking
PTs. Don't bother hooking tdp_mmu_iter_set_spte() as it is only used for
setting PTEs in operations unsupported by TDX: splitting huge pages and
write protecting. Sprinkle KVM_BUG_ON()s to document as code that these
paths are not supported for mirrored page tables. For zapping operations,
leave those for near future changes.
Many operations in the TDP MMU depend on atomicity of the PTE update.
While the mirror PTE on KVM's side can be updated atomically, the update
that happens inside the external operations (S-EPT updates via TDX module
call) can't happen atomically with the mirror update. The following race
could result during two vCPU's populating private memory:
* vcpu 1: atomically update 2M level mirror EPT entry to be present
* vcpu 2: read 2M level EPT entry that is present
* vcpu 2: walk down into 4K level EPT
* vcpu 2: atomically update 4K level mirror EPT entry to be present
* vcpu 2: set_exterma;_spte() to update 4K secure EPT entry => error
because 2M secure EPT entry is not populated yet
* vcpu 1: link_external_spt() to update 2M secure EPT entry
Prevent this by setting the mirror PTE to FROZEN_SPTE while the reflect
operations are performed. Only write the actual mirror PTE value once the
reflect operations have completed. When trying to set a PTE to present and
encountering a frozen SPTE, retry the fault.
By doing this the race is prevented as follows:
* vcpu 1: atomically update 2M level EPT entry to be FROZEN_SPTE
* vcpu 2: read 2M level EPT entry that is FROZEN_SPTE
* vcpu 2: find that the EPT entry is frozen
abandon page table walk to resume guest execution
* vcpu 1: link_external_spt() to update 2M secure EPT entry
* vcpu 1: atomically update 2M level EPT entry to be present (unfreeze)
* vcpu 2: resume guest execution
Depending on vcpu 1 state, vcpu 2 may result in EPT violation
again or make progress on guest execution
Signed-off-by: Isaku Yamahata <isaku.yamahata@intel.com>
Co-developed-by: Kai Huang <kai.huang@intel.com>
Signed-off-by: Kai Huang <kai.huang@intel.com>
Co-developed-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Yan Zhao <yan.y.zhao@intel.com>
Co-developed-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Message-ID: <20240718211230.1492011-15-rick.p.edgecombe@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Remove the redundant .hwapic_irr_update() ops.
If a vCPU has APICv enabled, KVM updates its RVI before VM-enter to L1
in vmx_sync_pir_to_irr(). This guarantees RVI is up-to-date and aligned
with the vIRR in the virtual APIC. So, no need to update RVI every time
the vIRR changes.
Note that KVM never updates vmcs02 RVI in .hwapic_irr_update() or
vmx_sync_pir_to_irr(). So, removing .hwapic_irr_update() has no
impact to the nested case.
Signed-off-by: Chao Gao <chao.gao@intel.com>
Link: https://lore.kernel.org/r/20241111085947.432645-1-chao.gao@intel.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Add VMX/SVM specific interrupt injection info the kvm_entry tracepoint.
As is done with kvm_exit, gather the information via a kvm_x86_ops hook
to avoid the moderately costly VMREADs on VMX when the tracepoint isn't
enabled.
Opportunistically rename the parameters in the get_exit_info()
declaration to match the names used by both SVM and VMX.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Link: https://lore.kernel.org/r/20240910200350.264245-2-mlevitsk@redhat.com
[sean: drop is_guest_mode() change, use intr_info/error_code for names]
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
When querying guest CPL to determine if a vCPU was preempted while in
kernel mode, bypass the register cache, i.e. always read SS.AR_BYTES from
the VMCS on Intel CPUs. If the kernel is running with full preemption
enabled, using the register cache in the preemption path can result in
stale and/or uninitialized data being cached in the segment cache.
In particular the following scenario is currently possible:
- vCPU is just created, and the vCPU thread is preempted before
SS.AR_BYTES is written in vmx_vcpu_reset().
- When scheduling out the vCPU task, kvm_arch_vcpu_in_kernel() =>
vmx_get_cpl() reads and caches '0' for SS.AR_BYTES.
- vmx_vcpu_reset() => seg_setup() configures SS.AR_BYTES, but doesn't
invoke vmx_segment_cache_clear() to invalidate the cache.
As a result, KVM retains a stale value in the cache, which can be read,
e.g. via KVM_GET_SREGS. Usually this is not a problem because the VMX
segment cache is reset on each VM-Exit, but if the userspace VMM (e.g KVM
selftests) reads and writes system registers just after the vCPU was
created, _without_ modifying SS.AR_BYTES, userspace will write back the
stale '0' value and ultimately will trigger a VM-Entry failure due to
incorrect SS segment type.
Note, the VM-Enter failure can also be avoided by moving the call to
vmx_segment_cache_clear() until after the vmx_vcpu_reset() initializes all
segments. However, while that change is correct and desirable (and will
come along shortly), it does not address the underlying problem that
accessing KVM's register caches from !task context is generally unsafe.
In addition to fixing the immediate bug, bypassing the cache for this
particular case will allow hardening KVM register caching log to assert
that the caches are accessed only when KVM _knows_ it is safe to do so.
Fixes: de63ad4cf497 ("KVM: X86: implement the logic for spinlock optimization")
Reported-by: Maxim Levitsky <mlevitsk@redhat.com>
Closes: https://lore.kernel.org/all/20240716022014.240960-3-mlevitsk@redhat.com
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Link: https://lore.kernel.org/r/20241009175002.1118178-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
KVM x86 misc changes for 6.12
- Advertise AVX10.1 to userspace (effectively prep work for the "real" AVX10
functionality that is on the horizon).
- Rework common MSR handling code to suppress errors on userspace accesses to
unsupported-but-advertised MSRs. This will allow removing (almost?) all of
KVM's exemptions for userspace access to MSRs that shouldn't exist based on
the vCPU model (the actual cleanup is non-trivial future work).
- Rework KVM's handling of x2APIC ICR, again, because AMD (x2AVIC) splits the
64-bit value into the legacy ICR and ICR2 storage, whereas Intel (APICv)
stores the entire 64-bit value a the ICR offset.
- Fix a bug where KVM would fail to exit to userspace if one was triggered by
a fastpath exit handler.
- Add fastpath handling of HLT VM-Exit to expedite re-entering the guest when
there's already a pending wake event at the time of the exit.
- Finally fix the RSM vs. nested VM-Enter WARN by forcing the vCPU out of
guest mode prior to signalling SHUTDOWN (architecturally, the SHUTDOWN is
supposed to hit L1, not L2).
|
|
Rename x86's the per-CPU vendor hooks used to enable virtualization in
hardware to align with the recently renamed arch hooks.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Kai Huang <kai.huang@intel.com>
Message-ID: <20240830043600.127750-7-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Rename all APIs related to feature MSRs from get_msr_feature() to
get_feature_msr(). The APIs get "feature MSRs", not "MSR features".
And unlike kvm_{g,s}et_msr_common(), the "feature" adjective doesn't
describe the helper itself.
No functional change intended.
Link: https://lore.kernel.org/r/20240802181935.292540-6-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
The use of static_call_cond() is essentially the same as static_call() on
x86 (e.g. static_call() now handles a NULL pointer as a NOP), so replace
it with static_call() to simplify the code.
Link: https://lore.kernel.org/all/3916caa1dcd114301a49beafa5030eca396745c1.1679456900.git.jpoimboe@kernel.org/
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Wei Wang <wei.w.wang@intel.com>
Link: https://lore.kernel.org/r/20240507133103.15052-2-wei.w.wang@intel.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
KVM VMX changes for 6.11
- Remove an unnecessary EPT TLB flush when enabling hardware.
- Fix a series of bugs that cause KVM to fail to detect nested pending posted
interrupts as valid wake eents for a vCPU executing HLT in L2 (with
HLT-exiting disable by L1).
- Misc cleanups
|
|
KVM generic changes for 6.11
- Enable halt poll shrinking by default, as Intel found it to be a clear win.
- Setup empty IRQ routing when creating a VM to avoid having to synchronize
SRCU when creating a split IRQCHIP on x86.
- Rework the sched_in/out() paths to replace kvm_arch_sched_in() with a flag
that arch code can use for hooking both sched_in() and sched_out().
- Take the vCPU @id as an "unsigned long" instead of "u32" to avoid
truncating a bogus value from userspace, e.g. to help userspace detect bugs.
- Mark a vCPU as preempted if and only if it's scheduled out while in the
KVM_RUN loop, e.g. to avoid marking it preempted and thus writing guest
memory when retrieving guest state during live migration blackout.
- A few minor cleanups
|
|
Check for a Requested Virtual Interrupt, i.e. a virtual interrupt that is
pending delivery, in vmx_has_nested_events() and drop the one-off
kvm_x86_ops.guest_apic_has_interrupt() hook.
In addition to dropping a superfluous hook, this fixes a bug where KVM
would incorrectly treat virtual interrupts _for L2_ as always enabled due
to kvm_arch_interrupt_allowed(), by way of vmx_interrupt_blocked(),
treating IRQs as enabled if L2 is active and vmcs12 is configured to exit
on IRQs, i.e. KVM would treat a virtual interrupt for L2 as a valid wake
event based on L1's IRQ blocking status.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240607172609.3205077-6-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Fold the guts of kvm_arch_sched_in() into kvm_arch_vcpu_load(), keying
off the recently added kvm_vcpu.scheduled_out as appropriate.
Note, there is a very slight functional change, as PLE shrink updates will
now happen after blasting WBINVD, but that is quite uninteresting as the
two operations do not interact in any way.
Acked-by: Kai Huang <kai.huang@intel.com>
Link: https://lore.kernel.org/r/20240522014013.1672962-4-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
In the case of SEV-SNP, whether or not a 2MB page can be mapped via a
2MB mapping in the guest's nested page table depends on whether or not
any subpages within the range have already been initialized as private
in the RMP table. The existing mixed-attribute tracking in KVM is
insufficient here, for instance:
- gmem allocates 2MB page
- guest issues PVALIDATE on 2MB page
- guest later converts a subpage to shared
- SNP host code issues PSMASH to split 2MB RMP mapping to 4K
- KVM MMU splits NPT mapping to 4K
- guest later converts that shared page back to private
At this point there are no mixed attributes, and KVM would normally
allow for 2MB NPT mappings again, but this is actually not allowed
because the RMP table mappings are 4K and cannot be promoted on the
hypervisor side, so the NPT mappings must still be limited to 4K to
match this.
Add a hook to determine the max NPT mapping size in situations like
this.
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Reviewed-by: Isaku Yamahata <isaku.yamahata@intel.com>
Message-ID: <20240501085210.2213060-3-michael.roth@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
In some cases, like with SEV-SNP, guest memory needs to be updated in a
platform-specific manner before it can be safely freed back to the host.
Wire up arch-defined hooks to the .free_folio kvm_gmem_aops callback to
allow for special handling of this sort when freeing memory in response
to FALLOC_FL_PUNCH_HOLE operations and when releasing the inode, and go
ahead and define an arch-specific hook for x86 since it will be needed
for handling memory used for SEV-SNP guests.
Signed-off-by: Michael Roth <michael.roth@amd.com>
Message-Id: <20231230172351.574091-6-michael.roth@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
guest_memfd pages are generally expected to be in some arch-defined
initial state prior to using them for guest memory. For SEV-SNP this
initial state is 'private', or 'guest-owned', and requires additional
operations to move these pages into a 'private' state by updating the
corresponding entries the RMP table.
Allow for an arch-defined hook to handle updates of this sort, and go
ahead and implement one for x86 so KVM implementations like AMD SVM can
register a kvm_x86_ops callback to handle these updates for SEV-SNP
guests.
The preparation callback is always called when allocating/grabbing
folios via gmem, and it is up to the architecture to keep track of
whether or not the pages are already in the expected state (e.g. the RMP
table in the case of SEV-SNP).
In some cases, it is necessary to defer the preparation of the pages to
handle things like in-place encryption of initial guest memory payloads
before marking these pages as 'private'/'guest-owned'. Add an argument
(always true for now) to kvm_gmem_get_folio() that allows for the
preparation callback to be bypassed. To detect possible issues in
the way userspace initializes memory, it is only possible to add an
unprepared page if it is not already included in the filemap.
Link: https://lore.kernel.org/lkml/ZLqVdvsF11Ddo7Dq@google.com/
Co-developed-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Message-Id: <20231230172351.574091-5-michael.roth@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Allow vendor modules to provide their own attributes on /dev/kvm.
To avoid proliferation of vendor ops, implement KVM_HAS_DEVICE_ATTR
and KVM_GET_DEVICE_ATTR in terms of the same function. You're not
supposed to use KVM_GET_DEVICE_ATTR to do complicated computations,
especially on /dev/kvm.
Reviewed-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Isaku Yamahata <isaku.yamahata@intel.com>
Message-ID: <20240404121327.3107131-5-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Pull kvm updates from Paolo Bonzini:
"S390:
- Changes to FPU handling came in via the main s390 pull request
- Only deliver to the guest the SCLP events that userspace has
requested
- More virtual vs physical address fixes (only a cleanup since
virtual and physical address spaces are currently the same)
- Fix selftests undefined behavior
x86:
- Fix a restriction that the guest can't program a PMU event whose
encoding matches an architectural event that isn't included in the
guest CPUID. The enumeration of an architectural event only says
that if a CPU supports an architectural event, then the event can
be programmed *using the architectural encoding*. The enumeration
does NOT say anything about the encoding when the CPU doesn't
report support the event *in general*. It might support it, and it
might support it using the same encoding that made it into the
architectural PMU spec
- Fix a variety of bugs in KVM's emulation of RDPMC (more details on
individual commits) and add a selftest to verify KVM correctly
emulates RDMPC, counter availability, and a variety of other
PMC-related behaviors that depend on guest CPUID and therefore are
easier to validate with selftests than with custom guests (aka
kvm-unit-tests)
- Zero out PMU state on AMD if the virtual PMU is disabled, it does
not cause any bug but it wastes time in various cases where KVM
would check if a PMC event needs to be synthesized
- Optimize triggering of emulated events, with a nice ~10%
performance improvement in VM-Exit microbenchmarks when a vPMU is
exposed to the guest
- Tighten the check for "PMI in guest" to reduce false positives if
an NMI arrives in the host while KVM is handling an IRQ VM-Exit
- Fix a bug where KVM would report stale/bogus exit qualification
information when exiting to userspace with an internal error exit
code
- Add a VMX flag in /proc/cpuinfo to report 5-level EPT support
- Rework TDP MMU root unload, free, and alloc to run with mmu_lock
held for read, e.g. to avoid serializing vCPUs when userspace
deletes a memslot
- Tear down TDP MMU page tables at 4KiB granularity (used to be
1GiB). KVM doesn't support yielding in the middle of processing a
zap, and 1GiB granularity resulted in multi-millisecond lags that
are quite impolite for CONFIG_PREEMPT kernels
- Allocate write-tracking metadata on-demand to avoid the memory
overhead when a kernel is built with i915 virtualization support
but the workloads use neither shadow paging nor i915 virtualization
- Explicitly initialize a variety of on-stack variables in the
emulator that triggered KMSAN false positives
- Fix the debugregs ABI for 32-bit KVM
- Rework the "force immediate exit" code so that vendor code
ultimately decides how and when to force the exit, which allowed
some optimization for both Intel and AMD
- Fix a long-standing bug where kvm_has_noapic_vcpu could be left
elevated if vCPU creation ultimately failed, causing extra
unnecessary work
- Cleanup the logic for checking if the currently loaded vCPU is
in-kernel
- Harden against underflowing the active mmu_notifier invalidation
count, so that "bad" invalidations (usually due to bugs elsehwere
in the kernel) are detected earlier and are less likely to hang the
kernel
x86 Xen emulation:
- Overlay pages can now be cached based on host virtual address,
instead of guest physical addresses. This removes the need to
reconfigure and invalidate the cache if the guest changes the gpa
but the underlying host virtual address remains the same
- When possible, use a single host TSC value when computing the
deadline for Xen timers in order to improve the accuracy of the
timer emulation
- Inject pending upcall events when the vCPU software-enables its
APIC to fix a bug where an upcall can be lost (and to follow Xen's
behavior)
- Fall back to the slow path instead of warning if "fast" IRQ
delivery of Xen events fails, e.g. if the guest has aliased xAPIC
IDs
RISC-V:
- Support exception and interrupt handling in selftests
- New self test for RISC-V architectural timer (Sstc extension)
- New extension support (Ztso, Zacas)
- Support userspace emulation of random number seed CSRs
ARM:
- Infrastructure for building KVM's trap configuration based on the
architectural features (or lack thereof) advertised in the VM's ID
registers
- Support for mapping vfio-pci BARs as Normal-NC (vaguely similar to
x86's WC) at stage-2, improving the performance of interacting with
assigned devices that can tolerate it
- Conversion of KVM's representation of LPIs to an xarray, utilized
to address serialization some of the serialization on the LPI
injection path
- Support for _architectural_ VHE-only systems, advertised through
the absence of FEAT_E2H0 in the CPU's ID register
- Miscellaneous cleanups, fixes, and spelling corrections to KVM and
selftests
LoongArch:
- Set reserved bits as zero in CPUCFG
- Start SW timer only when vcpu is blocking
- Do not restart SW timer when it is expired
- Remove unnecessary CSR register saving during enter guest
- Misc cleanups and fixes as usual
Generic:
- Clean up Kconfig by removing CONFIG_HAVE_KVM, which was basically
always true on all architectures except MIPS (where Kconfig
determines the available depending on CPU capabilities). It is
replaced either by an architecture-dependent symbol for MIPS, and
IS_ENABLED(CONFIG_KVM) everywhere else
- Factor common "select" statements in common code instead of
requiring each architecture to specify it
- Remove thoroughly obsolete APIs from the uapi headers
- Move architecture-dependent stuff to uapi/asm/kvm.h
- Always flush the async page fault workqueue when a work item is
being removed, especially during vCPU destruction, to ensure that
there are no workers running in KVM code when all references to
KVM-the-module are gone, i.e. to prevent a very unlikely
use-after-free if kvm.ko is unloaded
- Grab a reference to the VM's mm_struct in the async #PF worker
itself instead of gifting the worker a reference, so that there's
no need to remember to *conditionally* clean up after the worker
Selftests:
- Reduce boilerplate especially when utilize selftest TAP
infrastructure
- Add basic smoke tests for SEV and SEV-ES, along with a pile of
library support for handling private/encrypted/protected memory
- Fix benign bugs where tests neglect to close() guest_memfd files"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (246 commits)
selftests: kvm: remove meaningless assignments in Makefiles
KVM: riscv: selftests: Add Zacas extension to get-reg-list test
RISC-V: KVM: Allow Zacas extension for Guest/VM
KVM: riscv: selftests: Add Ztso extension to get-reg-list test
RISC-V: KVM: Allow Ztso extension for Guest/VM
RISC-V: KVM: Forward SEED CSR access to user space
KVM: riscv: selftests: Add sstc timer test
KVM: riscv: selftests: Change vcpu_has_ext to a common function
KVM: riscv: selftests: Add guest helper to get vcpu id
KVM: riscv: selftests: Add exception handling support
LoongArch: KVM: Remove unnecessary CSR register saving during enter guest
LoongArch: KVM: Do not restart SW timer when it is expired
LoongArch: KVM: Start SW timer only when vcpu is blocking
LoongArch: KVM: Set reserved bits as zero in CPUCFG
KVM: selftests: Explicitly close guest_memfd files in some gmem tests
KVM: x86/xen: fix recursive deadlock in timer injection
KVM: pfncache: simplify locking and make more self-contained
KVM: x86/xen: remove WARN_ON_ONCE() with false positives in evtchn delivery
KVM: x86/xen: inject vCPU upcall vector when local APIC is enabled
KVM: x86/xen: improve accuracy of Xen timers
...
|
|
Now that vmx->req_immediate_exit is used only in the scope of
vmx_vcpu_run(), use force_immediate_exit to detect that KVM should usurp
the VMX preemption to force a VM-Exit and let vendor code fully handle
forcing a VM-Exit.
Opportunsitically drop __kvm_request_immediate_exit() and just have
vendor code call smp_send_reschedule() directly. SVM already does this
when injecting an event while also trying to single-step an IRET, i.e.
it's not exactly secret knowledge that KVM uses a reschedule IPI to force
an exit.
Link: https://lore.kernel.org/r/20240110012705.506918-7-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Implement a workaround for an SNP erratum where the CPU will incorrectly
signal an RMP violation #PF if a hugepage (2MB or 1GB) collides with the
RMP entry of a VMCB, VMSA or AVIC backing page.
When SEV-SNP is globally enabled, the CPU marks the VMCB, VMSA, and AVIC
backing pages as "in-use" via a reserved bit in the corresponding RMP
entry after a successful VMRUN. This is done for _all_ VMs, not just
SNP-Active VMs.
If the hypervisor accesses an in-use page through a writable
translation, the CPU will throw an RMP violation #PF. On early SNP
hardware, if an in-use page is 2MB-aligned and software accesses any
part of the associated 2MB region with a hugepage, the CPU will
incorrectly treat the entire 2MB region as in-use and signal a an RMP
violation #PF.
To avoid this, the recommendation is to not use a 2MB-aligned page for
the VMCB, VMSA or AVIC pages. Add a generic allocator that will ensure
that the page returned is not 2MB-aligned and is safe to be used when
SEV-SNP is enabled. Also implement similar handling for the VMCB/VMSA
pages of nested guests.
[ mdr: Squash in nested guest handling from Ashish, commit msg fixups. ]
Reported-by: Alper Gun <alpergun@google.com> # for nested VMSA case
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Co-developed-by: Marc Orr <marcorr@google.com>
Signed-off-by: Marc Orr <marcorr@google.com>
Co-developed-by: Ashish Kalra <ashish.kalra@amd.com>
Signed-off-by: Ashish Kalra <ashish.kalra@amd.com>
Signed-off-by: Michael Roth <michael.roth@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Link: https://lore.kernel.org/r/20240126041126.1927228-22-michael.roth@amd.com
|
|
KVM x86 support for virtualizing Linear Address Masking (LAM)
Add KVM support for Linear Address Masking (LAM). LAM tweaks the canonicality
checks for most virtual address usage in 64-bit mode, such that only the most
significant bit of the untranslated address bits must match the polarity of the
last translated address bit. This allows software to use ignored, untranslated
address bits for metadata, e.g. to efficiently tag pointers for address
sanitization.
LAM can be enabled separately for user pointers and supervisor pointers, and
for userspace LAM can be select between 48-bit and 57-bit masking
- 48-bit LAM: metadata bits 62:48, i.e. LAM width of 15.
- 57-bit LAM: metadata bits 62:57, i.e. LAM width of 6.
For user pointers, LAM enabling utilizes two previously-reserved high bits from
CR3 (similar to how PCID_NOFLUSH uses bit 63): LAM_U48 and LAM_U57, bits 62 and
61 respectively. Note, if LAM_57 is set, LAM_U48 is ignored, i.e.:
- CR3.LAM_U48=0 && CR3.LAM_U57=0 == LAM disabled for user pointers
- CR3.LAM_U48=1 && CR3.LAM_U57=0 == LAM-48 enabled for user pointers
- CR3.LAM_U48=x && CR3.LAM_U57=1 == LAM-57 enabled for user pointers
For supervisor pointers, LAM is controlled by a single bit, CR4.LAM_SUP, with
the 48-bit versus 57-bit LAM behavior following the current paging mode, i.e.:
- CR4.LAM_SUP=0 && CR4.LA57=x == LAM disabled for supervisor pointers
- CR4.LAM_SUP=1 && CR4.LA57=0 == LAM-48 enabled for supervisor pointers
- CR4.LAM_SUP=1 && CR4.LA57=1 == LAM-57 enabled for supervisor pointers
The modified LAM canonicality checks:
- LAM_S48 : [ 1 ][ metadata ][ 1 ]
63 47
- LAM_U48 : [ 0 ][ metadata ][ 0 ]
63 47
- LAM_S57 : [ 1 ][ metadata ][ 1 ]
63 56
- LAM_U57 + 5-lvl paging : [ 0 ][ metadata ][ 0 ]
63 56
- LAM_U57 + 4-lvl paging : [ 0 ][ metadata ][ 0...0 ]
63 56..47
The bulk of KVM support for LAM is to emulate LAM's modified canonicality
checks. The approach taken by KVM is to "fill" the metadata bits using the
highest bit of the translated address, e.g. for LAM-48, bit 47 is sign-extended
to bits 62:48. The most significant bit, 63, is *not* modified, i.e. its value
from the raw, untagged virtual address is kept for the canonicality check. This
untagging allows
Aside from emulating LAM's canonical checks behavior, LAM has the usual KVM
touchpoints for selectable features: enumeration (CPUID.7.1:EAX.LAM[bit 26],
enabling via CR3 and CR4 bits, etc.
|
|
Declare the kvm_x86_ops hooks used to wire up paravirt TLB flushes when
running under Hyper-V if and only if CONFIG_HYPERV!=n. Wrapping yet more
code with IS_ENABLED(CONFIG_HYPERV) eliminates a handful of conditional
branches, and makes it super obvious why the hooks *might* be valid.
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Link: https://lore.kernel.org/r/20231018192325.1893896-1-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Introduce a new interface get_untagged_addr() to kvm_x86_ops to untag
the metadata from linear address. Call the interface in linearization
of instruction emulator for 64-bit mode.
When enabled feature like Intel Linear Address Masking (LAM) or AMD Upper
Address Ignore (UAI), linear addresses may be tagged with metadata that
needs to be dropped prior to canonicality checks, i.e. the metadata is
ignored.
Introduce get_untagged_addr() to kvm_x86_ops to hide the vendor specific
code, as sadly LAM and UAI have different semantics. Pass the emulator
flags to allow vendor specific implementation to precisely identify the
access type (LAM doesn't untag certain accesses).
Signed-off-by: Binbin Wu <binbin.wu@linux.intel.com>
Reviewed-by: Chao Gao <chao.gao@intel.com>
Tested-by: Xuelian Guo <xuelian.guo@intel.com>
Link: https://lore.kernel.org/r/20230913124227.12574-9-binbin.wu@linux.intel.com
[sean: massage changelog]
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
KVM SVM changes for 6.7:
- Report KVM_EXIT_SHUTDOWN instead of EINVAL if KVM intercepts SHUTDOWN while
running an SEV-ES guest.
- Clean up handling "failures" when KVM detects it can't emulate the "skip"
action for an instruction that has already been partially emulated. Drop a
hack in the SVM code that was fudging around the emulator code not giving
SVM enough information to do the right thing.
|
|
Refactor and rename can_emulate_instruction() to allow vendor code to
return more than true/false, e.g. to explicitly differentiate between
"retry", "fault", and "unhandleable". For now, just do the plumbing, a
future patch will expand SVM's implementation to signal outright failure
if KVM attempts EMULTYPE_SKIP on an SEV guest.
No functional change intended (or rather, none that are visible to the
guest or userspace).
Link: https://lore.kernel.org/r/20230825013621.2845700-4-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
When running android emulator (which is based on QEMU 2.12) on
certain Intel hosts with kernel version 6.3-rc1 or above, guest
will freeze after loading a snapshot. This is almost 100%
reproducible. By default, the android emulator will use snapshot
to speed up the next launching of the same android guest. So
this breaks the android emulator badly.
I tested QEMU 8.0.4 from Debian 12 with an Ubuntu 22.04 guest by
running command "loadvm" after "savevm". The same issue is
observed. At the same time, none of our AMD platforms is impacted.
More experiments show that loading the KVM module with
"enable_apicv=false" can workaround it.
The issue started to show up after commit 8e6ed96cdd50 ("KVM: x86:
fire timer when it is migrated and expired, and in oneshot mode").
However, as is pointed out by Sean Christopherson, it is introduced
by commit 967235d32032 ("KVM: vmx: clear pending interrupts on
KVM_SET_LAPIC"). commit 8e6ed96cdd50 ("KVM: x86: fire timer when
it is migrated and expired, and in oneshot mode") just makes it
easier to hit the issue.
Having both commits, the oneshot lapic timer gets fired immediately
inside the KVM_SET_LAPIC call when loading the snapshot. On Intel
platforms with APIC virtualization and posted interrupt processing,
this eventually leads to setting the corresponding PIR bit. However,
the whole PIR bits get cleared later in the same KVM_SET_LAPIC call
by apicv_post_state_restore. This leads to timer interrupt lost.
The fix is to move vmx_apicv_post_state_restore to the beginning of
the KVM_SET_LAPIC call and rename to vmx_apicv_pre_state_restore.
What vmx_apicv_post_state_restore does is actually clearing any
former apicv state and this behavior is more suitable to carry out
in the beginning.
Fixes: 967235d32032 ("KVM: vmx: clear pending interrupts on KVM_SET_LAPIC")
Cc: stable@vger.kernel.org
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Haitao Shan <hshan@google.com>
Link: https://lore.kernel.org/r/20230913000215.478387-1-hshan@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Reject KVM_SET_SREGS{2} with -EINVAL if the incoming CR0 is invalid,
e.g. due to setting bits 63:32, illegal combinations, or to a value that
isn't allowed in VMX (non-)root mode. The VMX checks in particular are
"fun" as failure to disallow Real Mode for an L2 that is configured with
unrestricted guest disabled, when KVM itself has unrestricted guest
enabled, will result in KVM forcing VM86 mode to virtual Real Mode for
L2, but then fail to unwind the related metadata when synthesizing a
nested VM-Exit back to L1 (which has unrestricted guest enabled).
Opportunistically fix a benign typo in the prototype for is_valid_cr4().
Cc: stable@vger.kernel.org
Reported-by: syzbot+5feef0b9ee9c8e9e5689@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/000000000000f316b705fdf6e2b4@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20230613203037.1968489-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
KVM SVM changes for 6.4:
- Add support for virtual NMIs
- Fixes for edge cases related to virtual interrupts
|
|
Rename the Hyper-V hooks for TLB flushing to match the naming scheme used
by all the other TLB flushing hooks, e.g. in kvm_x86_ops, vendor code,
arch hooks from common code, etc.
Reviewed-by: David Matlack <dmatlack@google.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Link: https://lore.kernel.org/r/20230405003133.419177-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Add support for SVM's Virtual NMIs implementation, which adds proper
tracking of virtual NMI blocking, and an intr_ctrl flag that software can
set to mark a virtual NMI as pending. Pending virtual NMIs are serviced
by hardware if/when virtual NMIs become unblocked, i.e. act more or less
like real NMIs.
Introduce two new kvm_x86_ops callbacks so to support SVM's vNMI, as KVM
needs to treat a pending vNMI as partially injected. Specifically, if
two NMIs (for L1) arrive concurrently in KVM's software model, KVM's ABI
is to inject one and pend the other. Without vNMI, KVM manually tracks
the pending NMI and uses NMI windows to detect when the NMI should be
injected.
With vNMI, the pending NMI is simply stuffed into the VMCB and handed
off to hardware. This means that KVM needs to be able to set a vNMI
pending on-demand, and also query if a vNMI is pending, e.g. to honor the
"at most one NMI pending" rule and to preserve all NMIs across save and
restore.
Warn if KVM attempts to open an NMI window when vNMI is fully enabled,
as the above logic should prevent KVM from ever getting to
kvm_check_and_inject_events() with two NMIs pending _in software_, and
the "at most one NMI pending" logic should prevent having an NMI pending
in hardware and an NMI pending in software if NMIs are also blocked, i.e.
if KVM can't immediately inject the second NMI.
Signed-off-by: Santosh Shukla <Santosh.Shukla@amd.com>
Co-developed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Link: https://lore.kernel.org/r/20230227084016.3368-11-santosh.shukla@amd.com
[sean: rewrite shortlog and changelog, massage code comments]
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
The first half or so patches fix semi-urgent, real-world relevant APICv
and AVIC bugs.
The second half fixes a variety of AVIC and optimized APIC map bugs
where KVM doesn't play nice with various edge cases that are
architecturally legal(ish), but are unlikely to occur in most real world
scenarios
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Track the per-vendor required APICv inhibits with a variable instead of
calling into vendor code every time KVM wants to query the set of
required inhibits. The required inhibits are a property of the vendor's
virtualization architecture, i.e. are 100% static.
Using a variable allows the compiler to inline the check, e.g. generate
a single-uop TEST+Jcc, and thus eliminates any desire to avoid checking
inhibits for performance reasons.
No functional change intended.
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20230106011306.85230-32-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Move the .check_processor_compatibility() callback from kvm_x86_init_ops
to kvm_x86_ops to allow a future patch to do compatibility checks during
CPU hotplug.
Do kvm_ops_update() before compat checks so that static_call() can be
used during compat checks.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Kai Huang <kai.huang@intel.com>
Message-Id: <20221130230934.1014142-40-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
To make terminology between Hyper-V-on-KVM and KVM-on-Hyper-V consistent,
rename 'enable_direct_tlbflush' to 'enable_l2_tlb_flush'. The change
eliminates the use of confusing 'direct' and adds the missing underscore.
No functional change.
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20221101145426.251680-6-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Vendor-specific code that deals with SMI injection and saving/restoring
SMM state is not needed if CONFIG_KVM_SMM is disabled, so remove the
four callbacks smi_allowed, enter_smm, leave_smm and enable_smi_window.
The users in svm/nested.c and x86.c also have to be compiled out; the
amount of #ifdef'ed code is small and it's not worth moving it to
smm.c.
enter_smm is now used only within #ifdef CONFIG_KVM_SMM, and the stub
can therefore be removed.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20220929172016.319443-7-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Rename the kvm_x86_ops hook for exception injection to better reflect
reality, and to align with pretty much every other related function name
in KVM.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Link: https://lore.kernel.org/r/20220830231614.3580124-14-seanjc@google.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Restrict get_mt_mask() to a u8 and reintroduce using a RET0 static_call
for the SVM implementation. EPT stores the memtype information in the
lower 8 bits (bits 6:3 to be precise), and even returns a shifted u8
without an explicit cast to a larger type; there's no need to return a
full u64.
Note, RET0 doesn't play nice with a u64 return on 32-bit kernels, see
commit bf07be36cd88 ("KVM: x86: do not use KVM_X86_OP_OPTIONAL_RET0 for
get_mt_mask").
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220714153707.3239119-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
With IPI virtualization enabled, the processor emulates writes to
APIC registers that would send IPIs. The processor sets the bit
corresponding to the vector in target vCPU's PIR and may send a
notification (IPI) specified by NDST and NV fields in target vCPU's
Posted-Interrupt Descriptor (PID). It is similar to what IOMMU
engine does when dealing with posted interrupt from devices.
A PID-pointer table is used by the processor to locate the PID of a
vCPU with the vCPU's APIC ID. The table size depends on maximum APIC
ID assigned for current VM session from userspace. Allocating memory
for PID-pointer table is deferred to vCPU creation, because irqchip
mode and VM-scope maximum APIC ID is settled at that point. KVM can
skip PID-pointer table allocation if !irqchip_in_kernel().
Like VT-d PI, if a vCPU goes to blocked state, VMM needs to switch its
notification vector to wakeup vector. This can ensure that when an IPI
for blocked vCPUs arrives, VMM can get control and wake up blocked
vCPUs. And if a VCPU is preempted, its posted interrupt notification
is suppressed.
Note that IPI virtualization can only virualize physical-addressing,
flat mode, unicast IPIs. Sending other IPIs would still cause a
trap-like APIC-write VM-exit and need to be handled by VMM.
Signed-off-by: Chao Gao <chao.gao@intel.com>
Signed-off-by: Zeng Guang <guang.zeng@intel.com>
Message-Id: <20220419154510.11938-1-guang.zeng@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 updates for 5.19
- Add support for the ARMv8.6 WFxT extension
- Guard pages for the EL2 stacks
- Trap and emulate AArch32 ID registers to hide unsupported features
- Ability to select and save/restore the set of hypercalls exposed
to the guest
- Support for PSCI-initiated suspend in collaboration with userspace
- GICv3 register-based LPI invalidation support
- Move host PMU event merging into the vcpu data structure
- GICv3 ITS save/restore fixes
- The usual set of small-scale cleanups and fixes
[Due to the conflict, KVM_SYSTEM_EVENT_SEV_TERM is relocated
from 4 to 6. - Paolo]
|
|
Flush the CPU caches when memory is reclaimed from an SEV guest (where
reclaim also includes it being unmapped from KVM's memslots). Due to lack
of coherency for SEV encrypted memory, failure to flush results in silent
data corruption if userspace is malicious/broken and doesn't ensure SEV
guest memory is properly pinned and unpinned.
Cache coherency is not enforced across the VM boundary in SEV (AMD APM
vol.2 Section 15.34.7). Confidential cachelines, generated by confidential
VM guests have to be explicitly flushed on the host side. If a memory page
containing dirty confidential cachelines was released by VM and reallocated
to another user, the cachelines may corrupt the new user at a later time.
KVM takes a shortcut by assuming all confidential memory remain pinned
until the end of VM lifetime. Therefore, KVM does not flush cache at
mmu_notifier invalidation events. Because of this incorrect assumption and
the lack of cache flushing, malicous userspace can crash the host kernel:
creating a malicious VM and continuously allocates/releases unpinned
confidential memory pages when the VM is running.
Add cache flush operations to mmu_notifier operations to ensure that any
physical memory leaving the guest VM get flushed. In particular, hook
mmu_notifier_invalidate_range_start and mmu_notifier_release events and
flush cache accordingly. The hook after releasing the mmu lock to avoid
contention with other vCPUs.
Cc: stable@vger.kernel.org
Suggested-by: Sean Christpherson <seanjc@google.com>
Reported-by: Mingwei Zhang <mizhang@google.com>
Signed-off-by: Mingwei Zhang <mizhang@google.com>
Message-Id: <20220421031407.2516575-4-mizhang@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Add optional callback .vcpu_get_apicv_inhibit_reasons returning
extra inhibit reasons that prevent APICv from working on this vCPU.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20220322174050.241850-6-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
KVM_X86_OP_OPTIONAL_RET0 can only be used with 32-bit return values on 32-bit
systems, because unsigned long is only 32-bits wide there and 64-bit values
are returned in edx:eax.
Reported-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
A few vendor callbacks are only used by VMX, but they return an integer
or bool value. Introduce KVM_X86_OP_OPTIONAL_RET0 for them: if a func is
NULL in struct kvm_x86_ops, it will be changed to __static_call_return0
when updating static calls.
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
All their invocations are conditional on vcpu->arch.apicv_active,
meaning that they need not be implemented by vendor code: even
though at the moment both vendors implement APIC virtualization,
all of them can be optional. In fact SVM does not need many of
them, and their implementation can be deleted now.
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The original use of KVM_X86_OP_NULL, which was to mark calls
that do not follow a specific naming convention, is not in use
anymore. Instead, let's mark calls that are optional because
they are always invoked within conditionals or with static_call_cond.
Those that are _not_, i.e. those that are defined with KVM_X86_OP,
must be defined by both vendor modules or some kind of NULL pointer
dereference is bound to happen at runtime.
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The two ioctls used to implement userspace-accelerated TPR,
KVM_TPR_ACCESS_REPORTING and KVM_SET_VAPIC_ADDR, are available
even if hardware-accelerated TPR can be used. So there is
no reason not to report KVM_CAP_VAPIC.
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Use slightly more verbose names for the so called "memory encrypt",
a.k.a. "mem enc", kvm_x86_ops hooks to bridge the gap between the current
super short kvm_x86_ops names and SVM's more verbose, but non-conforming
names. This is a step toward using kvm-x86-ops.h with KVM_X86_CVM_OP()
to fill svm_x86_ops.
Opportunistically rename mem_enc_op() to mem_enc_ioctl() to better
reflect its true nature, as it really is a full fledged ioctl() of its
own. Ideally, the hook would be named confidential_vm_ioctl() or so, as
the ioctl() is a gateway to more than just memory encryption, and because
its underlying purpose to support Confidential VMs, which can be provided
without memory encryption, e.g. if the TCB of the guest includes the host
kernel but not host userspace, or by isolation in hardware without
encrypting memory. But, diverging from KVM_MEMORY_ENCRYPT_OP even
further is undeseriable, and short of creating alises for all related
ioctl()s, which introduces a different flavor of divergence, KVM is stuck
with the nomenclature.
Defer renaming SVM's functions to a future commit as there are additional
changes needed to make SVM fully conforming and to match reality (looking
at you, svm_vm_copy_asid_from()).
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220128005208.4008533-20-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
