| Age | Commit message (Collapse) | Author |
|---|
|
Direct access to the struct bus_type dev_root pointer is going away soon
so replace that with a call to bus_get_dev_root() instead, which is what
it is there for.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: x86@kernel.org
Cc: "H. Peter Anvin" <hpa@zytor.com>
Link: https://lore.kernel.org/r/20230313182918.1312597-10-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove support for context switching between the guest's and host's
desired UMWAIT_CONTROL. Propagating the guest's value to hardware isn't
required for correct functionality, e.g. KVM intercepts reads and writes
to the MSR, and the latency effects of the settings controlled by the
MSR are not architecturally visible.
As a general rule, KVM should not allow the guest to control power
management settings unless explicitly enabled by userspace, e.g. see
KVM_CAP_X86_DISABLE_EXITS. E.g. Intel's SDM explicitly states that C0.2
can improve the performance of SMT siblings. A devious guest could
disable C0.2 so as to improve the performance of their workloads at the
detriment to workloads running in the host or on other VMs.
Wholesale removal of UMWAIT_CONTROL context switching also fixes a race
condition where updates from the host may cause KVM to enter the guest
with the incorrect value. Because updates are are propagated to all
CPUs via IPI (SMP function callback), the value in hardware may be
stale with respect to the cached value and KVM could enter the guest
with the wrong value in hardware. As above, the guest can't observe the
bad value, but it's a weird and confusing wart in the implementation.
Removal also fixes the unnecessary usage of VMX's atomic load/store MSR
lists. Using the lists is only necessary for MSRs that are required for
correct functionality immediately upon VM-Enter/VM-Exit, e.g. EFER on
old hardware, or for MSRs that need to-the-uop precision, e.g. perf
related MSRs. For UMWAIT_CONTROL, the effects are only visible in the
kernel via TPAUSE/delay(), and KVM doesn't do any form of delay in
vcpu_vmx_run(). Using the atomic lists is undesirable as they are more
expensive than direct RDMSR/WRMSR.
Furthermore, even if giving the guest control of the MSR is legitimate,
e.g. in pass-through scenarios, it's not clear that the benefits would
outweigh the overhead. E.g. saving and restoring an MSR across a VMX
roundtrip costs ~250 cycles, and if the guest diverged from the host
that cost would be paid on every run of the guest. In other words, if
there is a legitimate use case then it should be enabled by a new
per-VM capability.
Note, KVM still needs to emulate MSR_IA32_UMWAIT_CONTROL so that it can
correctly expose other WAITPKG features to the guest, e.g. TPAUSE,
UMWAIT and UMONITOR.
Fixes: 6e3ba4abcea56 ("KVM: vmx: Emulate MSR IA32_UMWAIT_CONTROL")
Cc: stable@vger.kernel.org
Cc: Jingqi Liu <jingqi.liu@intel.com>
Cc: Tao Xu <tao3.xu@intel.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200623005135.10414-1-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
.. in order to fix a -Wmissing-prototypes warning.
No functional change.
Signed-off-by: Benjamin Thiel <b.thiel@posteo.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: kvm@vger.kernel.org
Link: https://lkml.kernel.org/r/20200123172945.7235-1-b.thiel@posteo.de
|
|
UMWAIT and TPAUSE instructions use 32bit IA32_UMWAIT_CONTROL at MSR index
E1H to determines the maximum time in TSC-quanta that the processor can
reside in either C0.1 or C0.2.
This patch emulates MSR IA32_UMWAIT_CONTROL in guest and differentiate
IA32_UMWAIT_CONTROL between host and guest. The variable
mwait_control_cached in arch/x86/kernel/cpu/umwait.c caches the MSR value,
so this patch uses it to avoid frequently rdmsr of IA32_UMWAIT_CONTROL.
Co-developed-by: Jingqi Liu <jingqi.liu@intel.com>
Signed-off-by: Jingqi Liu <jingqi.liu@intel.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Currently, failure of cpuhp_setup_state() is ignored and the syscore ops
and the control interfaces can still be added even after the failure. But,
this error handling will cause a few issues:
1. The CPUs may have different values in the IA32_UMWAIT_CONTROL
MSR because there is no way to roll back the control MSR on
the CPUs which already set the MSR before the failure.
2. If the sysfs interface is added successfully, there will be a mismatch
between the global control value and the control MSR:
- The interface shows the default global control value. But,
the control MSR is not set to the value because the CPU online
function, which is supposed to set the MSR to the value,
is not installed.
- If the sysadmin changes the global control value through
the interface, the control MSR on all current online CPUs is
set to the new value. But, the control MSR on newly onlined CPUs
after the value change will not be set to the new value due to
lack of the CPU online function.
3. On resume from suspend/hibernation, the boot CPU restores the control
MSR to the global control value through the syscore ops. But, the
control MSR on all APs is not set due to lake of the CPU online
function.
To solve the issues and enforce consistent behavior on the failure
of the CPU hotplug setup, make the following changes:
1. Cache the original control MSR value which is configured by
hardware or BIOS before kernel boot. This value is likely to
be 0. But it could be a different number as well. Cache the
control MSR only once before the MSR is changed.
2. Add the CPU offline function so that the MSR is restored to the
original control value on all CPUs on the failure.
3. On the failure, exit from cpumait_init() so that the syscore ops
and the control interfaces are not added.
Reported-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/1565401237-60936-1-git-send-email-fenghua.yu@intel.com
|
|
IA32_UMWAIT_CONTROL[31:2] determines the maximum time in TSC-quanta
that processor can stay in C0.1 or C0.2. A zero value means no maximum
time.
Each instruction sets its own deadline in the instruction's implicit
input EDX:EAX value. The instruction wakes up if the time-stamp counter
reaches or exceeds the specified deadline, or the umwait maximum time
expires, or a store happens in the monitored address range in umwait.
The administrator can write an unsigned 32-bit number to
/sys/devices/system/cpu/umwait_control/max_time to change the default
value. Note that a value of zero means there is no limit. The lower two
bits of the value must be zero.
[ tglx: Simplify the write function. Massage changelog ]
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Cc: "Borislav Petkov" <bp@alien8.de>
Cc: "H Peter Anvin" <hpa@zytor.com>
Cc: "Andy Lutomirski" <luto@kernel.org>
Cc: "Peter Zijlstra" <peterz@infradead.org>
Cc: "Ravi V Shankar" <ravi.v.shankar@intel.com>
Link: https://lkml.kernel.org/r/1560994438-235698-5-git-send-email-fenghua.yu@intel.com
|
|
C0.2 state in umwait and tpause instructions can be enabled or disabled
on a processor through IA32_UMWAIT_CONTROL MSR register.
By default, C0.2 is enabled and the user wait instructions results in
lower power consumption with slower wakeup time.
But in real time systems which require faster wakeup time although power
savings could be smaller, the administrator needs to disable C0.2 and all
umwait invocations from user applications use C0.1.
Create a sysfs interface which allows the administrator to control C0.2
state during run time.
Andy Lutomirski suggested to turn off local irqs before writing the MSR to
ensure the cached control value is not changed by a concurrent sysfs write
from a different CPU via IPI.
[ tglx: Simplified the update logic in the write function and got rid of
all the convoluted type casts. Added a shared update function and
made the namespace consistent. Moved the sysfs create invocation.
Massaged changelog ]
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Cc: "Borislav Petkov" <bp@alien8.de>
Cc: "H Peter Anvin" <hpa@zytor.com>
Cc: "Andy Lutomirski" <luto@kernel.org>
Cc: "Peter Zijlstra" <peterz@infradead.org>
Cc: "Ravi V Shankar" <ravi.v.shankar@intel.com>
Link: https://lkml.kernel.org/r/1560994438-235698-4-git-send-email-fenghua.yu@intel.com
|
|
umwait or tpause allows the processor to enter a light-weight
power/performance optimized state (C0.1 state) or an improved
power/performance optimized state (C0.2 state) for a period specified by
the instruction or until the system time limit or until a store to the
monitored address range in umwait.
IA32_UMWAIT_CONTROL MSR register allows the OS to enable/disable C0.2 on
the processor and to set the maximum time the processor can reside in C0.1
or C0.2.
By default C0.2 is enabled so the user wait instructions can enter the
C0.2 state to save more power with slower wakeup time.
Andy Lutomirski proposed to set the maximum umwait time to 100000 cycles by
default. A quote from Andy:
"What I want to avoid is the case where it works dramatically differently
on NO_HZ_FULL systems as compared to everything else. Also, UMWAIT may
behave a bit differently if the max timeout is hit, and I'd like that
path to get exercised widely by making it happen even on default
configs."
A sysfs interface to adjust the time and the C0.2 enablement is provided in
a follow up change.
[ tglx: Renamed MSR_IA32_UMWAIT_CONTROL_MAX_TIME to
MSR_IA32_UMWAIT_CONTROL_TIME_MASK because the constant is used as
mask throughout the code.
Massaged comments and changelog ]
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ashok Raj <ashok.raj@intel.com>
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Cc: "Borislav Petkov" <bp@alien8.de>
Cc: "H Peter Anvin" <hpa@zytor.com>
Cc: "Peter Zijlstra" <peterz@infradead.org>
Cc: "Tony Luck" <tony.luck@intel.com>
Cc: "Ravi V Shankar" <ravi.v.shankar@intel.com>
Link: https://lkml.kernel.org/r/1560994438-235698-3-git-send-email-fenghua.yu@intel.com
|
