| Age | Commit message (Collapse) | Author |
|---|
|
Add basic HDMI video output support. Currently, only RGB888 output
pixel format is supported. At the LVDS input side, the driver
supports single LVDS link and dual LVDS links with "jeida-24" LVDS
mapping.
Product link:
https://www.ite.com.tw/en/product/cate1/IT6263
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241104032806.611890-11-victor.liu@nxp.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
|
|
TDP158 is an AC-coupled DVI / HDMI to TMDS level shifting Redriver.
It supports DVI 1.0, HDMI 1.4b and 2.0b.
It supports 4 TMDS channels, HPD, and a DDC interface.
It supports dual power supply rails (1.1V on VDD, 3.3V on VCC)
for power reduction. Several methods of power management are
implemented to reduce overall power consumption.
It supports fixed receiver EQ gain using I2C or pin strap to
compensate for different lengths input cable or board traces.
Features
- AC-coupled TMDS or DisplayPort dual-mode physical layer input
to HDMI 2.0b TMDS physical layer output supporting up to 6Gbps
data rate, compatible with HDMI 2.0b electrical parameters
- DisplayPort dual-mode standard version 1.1
- Programmable fixed receiver equalizer up to 15.5dB
- Global or independent high speed lane control, pre-emphasis
and transmit swing, and slew rate control
- I2C or pin strap programmable
- Configurable as a DisplayPort redriver through I2C
- Full lane swap on main lanes
- Low power consumption (200 mW at 6Gbps, 8 mW in shutdown)
https://www.ti.com/lit/ds/symlink/tdp158.pdf
On our board, I2C_EN is pulled high.
Thus, this code defines a module_i2c_driver.
The default settings work fine for our use-case.
So this basic driver doesn't need to tweak any I2C registers.
Signed-off-by: Marc Gonzalez <mgonzalez@freebox.fr>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240812-tdp158-v5-2-78684a84ec23@freebox.fr
|
|
Add a new LVDS controller driver for sam9x7 which does the following:
- Prepares and enables the LVDS Peripheral clock
- Defines its connector type as DRM_MODE_CONNECTOR_LVDS and adds itself
to the global bridge list.
- Identifies its output endpoint as panel and adds it to the encoder
display pipeline
- Enables the LVDS serializer
Signed-off-by: Manikandan Muralidharan <manikandan.m@microchip.com>
Signed-off-by: Dharma Balasubiramani <dharma.b@microchip.com>
Acked-by: Hari Prasath Gujulan Elango <hari.prasathge@microchip.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240421011050.43265-3-dharma.b@microchip.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240421011050.43265-3-dharma.b@microchip.com
|
|
Several USB-C controllers implement a pretty simple DRM bridge which
implements just the HPD notification operations. Add special helper
for creating such simple bridges.
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231203114333.1305826-5-dmitry.baryshkov@linaro.org
|
|
Define a helper for creating simple transparent bridges which serve the
only purpose of linking devices into the bridge chain up to the last
bridge representing the connector. This is especially useful for
DP/USB-C bridge chains, which can span across several devices, but do
not require any additional functionality from the intermediate bridges.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231203114333.1305826-2-dmitry.baryshkov@linaro.org
|
|
Samsung MIPI DSIM controller is common DSI IP that can be used in various
SoCs like Exynos, i.MX8M Mini/Nano.
In order to access this DSI controller between various platform SoCs,
the ideal way to incorporate this in the drm stack is via the drm bridge
driver.
We already have a consolidated code for supporting component and bridge
based DRM drivers, so keep the exynos component based code in existing
exynos_drm_dsi.c and move generic bridge code as part of samsung-dsim.c
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Move the cadence dsi bridge under drm/bridge/cadence directory, to
prepare for adding j721e wrapper support
Signed-off-by: Rahul T R <r-ravikumar@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230103101951.10963-4-r-ravikumar@ti.com
|
|
This patch adds a drm bridge driver for i.MX8qm/qxp pixel combiner.
The pixel combiner takes two output streams from a single display
controller and manipulates the two streams to support a number
of modes(bypass, pixel combine, YUV444 to YUV422, split_RGB) configured
as either one screen, two screens, or virtual screens. The pixel
combiner is also responsible for generating some of the control signals
for the pixel link output channel. For now, the driver only supports
the bypass mode.
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # Colibri iMX8X, LT170410-2WHC, LP156WF1
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220611141421.718743-5-victor.liu@nxp.com
|
|
TI DLPC3433 is a MIPI DSI based display controller bridge
for processing high resolution DMD based projectors.
It has a flexible configuration of MIPI DSI and DPI signal
input that produces a DMD output in RGB565, RGB666, RGB888
formats.
It supports upto 720p resolution with 60 and 120 Hz refresh
rates.
Add bridge driver for it.
Signed-off-by: Christopher Vollo <chris@renewoutreach.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220603140349.3563612-2-jagan@amarulasolutions.com
|
|
The i.MX8MP contains two syscon registers which are responsible
for configuring the on-SoC DPI-to-LVDS serializer. Implement a
simple bridge driver for this serializer.
--
- Add sentinel of_device_table
- Add RB from Sam
- Rename to fsl-ldb altogether
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Robby Cai <robby.cai@nxp.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
V2: - Rename syscon to fsl,syscon
V3: - Consistently use MX8MP
V4: - Fix MODULE_DESCRIPTION to also use MX8MP
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220426193645.244792-2-marex@denx.de
|
|
Add driver for Lontium LT9211 Single/Dual-Link DSI/LVDS or Single DPI to
Single-link/Dual-Link DSI/LVDS or Single DPI bridge. This chip is highly
capable at converting formats, but sadly it is also highly undocumented.
This driver is written without any documentation from Lontium and based
only on shreds of information available in various obscure example codes,
hence long runs of unknown register patches and lengthy delays in various
places. Whichever register meaning could be divined from its behavior has
at least a comment around it.
Currently the only mode tested is Single-link DSI to Single-link LVDS.
Dual-link LVDS might work as well, the register programming is in place,
but is untested.
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419143958.94873-2-marex@denx.de
|
|
This adds support for the iTE IT6505.
This device can convert DPI signal to DP output.
From: Allen Chen <allen.chen@ite.com.tw>
Tested-by: Hsin-yi Wang <hsinyi@chromium.org>
Signed-off-by: Hermes Wu <hermes.wu@ite.com.tw>
Signed-off-by: Allen Chen <allen.chen@ite.com.tw>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220114091502.333083-1-allen.chen@ite.com.tw
|
|
Add driver for TI SN65DSI83 Single-link DSI to Single-link LVDS bridge
and TI SN65DSI84 Single-link DSI to Dual-link or 2x Single-link LVDS
bridge. TI SN65DSI85 is unsupported due to lack of hardware to test on,
but easy to add.
The driver operates the chip via I2C bus. Currently the LVDS clock are
always derived from DSI clock lane, which is the usual mode of operation.
Support for clock from external oscillator is not implemented, but it is
easy to add if ever needed. Only RGB888 pixel format is implemented, the
LVDS666 is not supported, but could be added if needed.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Loic Poulain <loic.poulain@linaro.org>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Valentin Raevsky <valentin@compulab.co.il>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210607174258.16300-2-marex@denx.de
|
|
This driver adds support for the ChromeOS EC ANX7688 HDMI to DP converter
For our use case, the only reason the Linux kernel driver is necessary is
to reject resolutions that require more bandwidth than what is available
on the DP side. DP bandwidth and lane count are reported by the bridge via
2 registers and, as far as we know, only chips that have a firmware
version greater than 0.85 support these two registers.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
[The driver is OF only so should depends on CONFIG_OF]
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
[convert to i2c driver, rename to cros_ec_anx7688, add err checks]
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210518141927.24795-3-dafna.hirschfeld@collabora.com
|
|
This commit is a simple driver for bridge HMDI it66121.
The input format is RBG and there is no color conversion.
Audio, HDCP and CEC are not supported yet.
Signed-off-by: Phong LE <ple@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210419071223.2673533-3-narmstrong@baylibre.com
|
|
Lontium LT8912B is a DSI to HDMI bridge.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210326121955.1266230-3-adrien.grassein@gmail.com
|
|
ICN6211 is MIPI-DSI to RGB Converter bridge from Chipone.
It has a flexible configuration of MIPI DSI signal input and
produce RGB565, RGB666, RGB888 output format.
Add bridge driver for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210322103328.66442-2-jagan@amarulasolutions.com
|
|
Add support for Lontium LT9611UXC HDMI bridge. Lontium LT9611UXC is a
DSI to HDMI bridge which supports two DSI ports and I2S port as an input
and HDMI port as output. Despite name being similar to LT9611, these
devices are different enough to warrant separate driver.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201102011435.1100930-3-dmitry.baryshkov@linaro.org
|
|
Add a new DRM bridge driver for Cadence MHDP8546 DPTX IP used in TI J721E
SoC. MHDP DPTX IP is the component that complies with VESA DisplayPort (DP)
and embedded Display Port (eDP) standards. It integrates uCPU running the
embedded Firmware (FW) interfaced over APB interface.
Basically, it takes a DPI stream as input and outputs it encoded in DP
format. Currently, it supports only SST mode.
Co-developed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Co-developed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Yuti Amonkar <yamonkar@cadence.com>
Signed-off-by: Swapnil Jakhade <sjakhade@cadence.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add very basic driver for Toshiba TC358762 DSI-to-DPI bridge, derived
from tc358764 driver and panel-raspberrypi-touchscreen. This driver is
meant to replace the panel-raspberrypi-touchscreen too, as the bridge
connection can be described in DT too.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: dri-devel@lists.freedesktop.org
Cc: Eric Anholt <eric@anholt.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: devicetree@vger.kernel.org
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam.ravnborg@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200809105705.6334-2-marex@denx.de
|
|
This driver is tested with two panels individually with Apq8016-IFC6309 board
https://www.inforcecomputing.com/products/single-board-computers-sbc/qualcomm-snapdragon-410-inforce-6309-micro-sbc
1. 1366x768@60 auo,b101xtn01 data-mapping = "jeida-24"
2. 800x480@60 innolux,at070tn92 data-mapping = "vesa-24"
- power off sequence in proper order
- put_unaligned_be16, put_unaligned_le32 macros used
- static function for mode_valid
- len initialized
- MODE_CLOCK_HIGH handled properly
- bus_formats handled in mode_valid
- GENMASK and FIELD_PREP used
- Kconfig proper indentation
- error handling endpoint data-lanes
- check for bus_formats unsupported
- display_timings naming local variables
- help modified
- ~vsdelay dynamic value set based on the
calculation of dsi speed, output speed, blanking
- panel->connector_type removed
- dual port implemented
- devm_drm_panel_bridge_add method used instead of panel
description modified
- regulator enable and disable with proper orders and delays
as per the spec
- removed drm_connector_status
- added bus_formats
- mdelay to usleep_range
- magic number to macros for CLRSI and mux registers
description modified
- replaced u32 instead of uint32_t
- updated alphabetic order of headers
- added SPDX identifier license
Signed-off-by: Vinay Simha BN <simhavcs@gmail.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam.ravnborg@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1594388491-15129-2-git-send-email-simhavcs@gmail.com
|
|
Lontium Lt9611 is a DSI to HDMI bridge which supports two DSI ports and
I2S port as an input and HDMI port as output
Co-developed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Co-developed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> # fix lt9611_bridge_mode_valid
Link: https://patchwork.freedesktop.org/patch/msgid/20200723163442.1280414-4-vkoul@kernel.org
|
|
This is a driver for video encoder with VGA and DVI/HDMI outputs.
There is no documentation for the chip -- the operation was guessed from
what was sniffed on a Dell Wyse 3020 ThinOS terminal, the register names
come from the ch7035 driver in Mediatek's GPL code dump.
Only bare minimum is implemented -- no fancy stuff, such as scaling. That
would only worsen our misery. We don't load the firmware and we don't need
to even bother enabling the MCU. There are probably no distributable
firmware images anyway.
Tested with a handful of monitors ranging from 1024x768@75 to 1400x1050@60,
with VGA as well as DVI.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200424213539.93157-4-lkundrak@v3.sk
|
|
This adds initial support for the NWL MIPI DSI Host controller found on
i.MX8 SoCs.
It adds support for the i.MX8MQ but the same IP can be found on
e.g. the i.MX8QXP.
It has been tested on the Librem 5 devkit using mxsfb.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Co-developed-by: Robert Chiras <robert.chiras@nxp.com>
Signed-off-by: Robert Chiras <robert.chiras@nxp.com>
Tested-by: Robert Chiras <robert.chiras@nxp.com>
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1cf5750f734e33d005564cd89c576eaf3c1c192b.1586427783.git.agx@sigxcpu.org
|
|
The TI TPD12S015 is an HDMI level shifter and ESD protector controlled
through GPIOs. Add a DRM bridge driver for the device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-17-laurent.pinchart@ideasonboard.com
|
|
Display connectors are modelled in DT as a device node, but have so far
been handled manually in several bridge drivers. This resulted in
duplicate code in several bridge drivers, with slightly different (and
thus confusing) logics.
In order to fix this, implement a bridge driver for display connectors.
The driver centralises logic for the DVI, HDMI, VGAn composite and
S-video connectors and exposes corresponding bridge operations.
This driver in itself doesn't solve the issue completely, changes in
bridge and display controller drivers are needed to make use of the new
connector driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-16-laurent.pinchart@ideasonboard.com
|
|
The dumb-vga-dac driver can support simple DRM bridges without being
limited to VGA DACs. Rename it to simple-bridge.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-12-laurent.pinchart@ideasonboard.com
|
|
Add basic support for the Toshiba TC358768 RGB to DSI bridge.
Not all the features of the TC358768 is implemented by the initial driver:
MIPI_DSI_MODE_VIDEO and MIPI_DSI_FMT_RGB888 is only supported and tested.
Only write is implemented for mipi_dsi_host_ops.transfer.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200131111553.472-3-peter.ujfalusi@ti.com
|
|
This patch adds drm_bridge driver for parade DSI to eDP bridge chip.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
[uli: followed API changes, removed FW update feature]
Signed-off-by: Ulrich Hecht <uli@fpond.eu>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191230090419.137141-3-enric.balletbo@collabora.com
|
|
lvds-encoder.c implementation is also suitable for LVDS decoders,
not just LVDS encoders.
Instead of creating a new driver for addressing support for
transparent LVDS decoders, repurpose lvds-encoder.c for the greater
good with this patch.
This patch only "rebrands" the lvds-encoder.c driver, to make it
suitable for hosting LVDS decoders support. The actual support for
LVDS decoders will come with a later patch.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1573660292-10629-6-git-send-email-fabrizio.castro@bp.renesas.com
|
|
As ANA78xx chips are designed and produced by Analogix Semiconductor,
Inc, move their driver codes into analogix subdirectory.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Torsten Duwe <duwe@suse.de>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20191107135202.2089C68BE1@verein.lst.de
|
|
Add a drm_bridge driver for the Toshiba TC358764 DSI to LVDS bridge.
Changes in v4:
- removed license blob,
- ordered includes,
- added error handling,
- fixed reset GPIO handling,
- added missing calls to the panel,
- custom OF graph code replaced with helpers,
- removed tc358764_poweroff from remove callback.
v5:
- fixed supply names,
- fixed broken console - added connector to fb_helper,
- added detach callback - unbinding works,
- fixed typo in error checking code,
- removed sparse bridge->encoder check - core does it already.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Maciej Purski <m.purski@samsung.com>
[ a.hajda@samsung.com: v4, v5 ]
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180725154644.25412-6-a.hajda@samsung.com
|
|
Add support for TI's sn65dsi86 dsi2edp bridge chip.
The chip converts DSI transmitted signal to eDP signal,
which is fed to the connected eDP panel.
This chip can be controlled via either i2c interface or
dsi interface. Currently in driver all the control registers
are being accessed through i2c interface only.
Also as of now HPD support has not been added to bridge
chip driver.
Changes in v1:
- Split the dt-bindings and the driver support into separate patches
(Andrzej Hajda).
- Use of gpiod APIs to parse and configure gpios instead of obsolete ones
(Andrzej Hajda).
- Use macros to define the register offsets (Andrzej Hajda).
Changes in v2:
- Separate out edp panel specific HW resource handling from bridge
driver and create a separate edp panel drivers to handle panel
specific mode information and HW resources (Sean Paul).
- Replace pr_* APIs to DRM_* APIs to log error or debug information
(Sean Paul).
- Remove some of the unnecessary structure/variable from driver (Sean
Paul).
- Rename the function and structure prefix "sn65dsi86" to "ti_sn_bridge"
(Sean Paul / Rob Herring).
- Remove most of the hard-coding and modified the bridge init sequence
based on current mode (Sean Paul).
- Remove the existing function to retrieve the EDID data and
implemented this as an i2c_adapter and use drm_get_edid() (Sean Paul).
- Remove the dummy irq handler implementation, will add back the
proper irq handling later (Sean Paul).
- Capture the required enable gpios in a single array based on dt entry
instead of having individual descriptor for each gpio (Sean Paul).
Changes in v3:
- Remove usage of irq_gpio and replace it as "interrupts" property (Rob
Herring).
- Remove the unnecessary header file inclusions (Sean Paul).
- Rearrange the header files in alphabetical order (Sean Paul).
- Use regmap interface to perform i2c transactions.
- Update Copyright/License field and address other review comments
(Jordan Crouse).
Changes in v4:
- Update License/Copyright (Sean Paul).
- Add Kconfig and Makefile changes (Sean Paul).
- Drop i2c gpio handling from this bridge driver, since i2c sda/scl gpios
will be handled by i2c master.
- Update required supplies names.
- Remove unnecessary goto statements (Sean Paul).
- Add mutex lock to power_ctrl API to avoid race conditions (Sean
Paul).
- Add support to parse reference clk frequency from dt(optional).
- Update the bridge chip enable/disable sequence.
Changes in v5:
- Fixed Kbuild test service reported warnings.
Changes in v6:
- Use PM runtime based ref-counting instead of local ref_count mechanism
(Stephen Boyd).
- Clean up some debug logs and indentations (Sean Paul).
- Simplify dp rate calculation (Sean Paul).
- Add support to configure refclk based on input REFCLK pin or DACP/N
pin (Stephen Boyd).
Changes in v7:
- Use static supply entries instead of dynamic allocation (Andrzej
Hajda).
- Defer bridge driver probe if panel is not probed (Andrzej Hajda).
- Update of_graph APIs for correct node reference management. (Andrzej
Hajda).
- Remove local display_mode object (Andrzej Hajda).
- Remove version id check function from driver.
Changes in v8:
- Move dsi register/attach function to bridge driver probe (Andrzej
Hajda).
- Introduce a new helper function to write 16bit words into consecutive
registers (Andrzej Hajda).
- Remove unnecessary macros (Andrzej Hajda).
Changes in v9:
- Remove dsi register/attach from bridge probe, since dsi dev register
completion also waits for any panel or bridge to get added. This creates
deadlock situation when bridge driver calls dsi dev register and
attach before bridge add, in its probe function.
- Fix issues faced during testing of bridge driver on actual HW.
- Remove unnecessary initializations (Stephen Boyd).
- Use local refclk lut size instead of global macro (Sean Paul).
Changes in v10:
- Use refclk to determine if continuous dsi clock is needed or not.
Changes in v11:
- Read DPPLL_SRC register to determine continuous clock instead of
using refclk handle (Stephen Boyd).
Changes in v12:
- Explain in comment as in why dsi dev registration is done in
bridge_attach (Andrzej Hajda).
- Move HPD disable to bridge_pre_enable (Andrzej Hajda).
- Make panel/DDC exclusive until HPD support is added (Andrzej Hajda).
Changes in v13:
- eDP panels report EDID via DP-AUX channel, so remove support for
dedicated DDC line (Andrzej Hajda).
Changes in v14:
- Remove unnecessary drm_panel checks (Andrzej Hajda).
Signed-off-by: Sandeep Panda <spanda@codeaurora.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1532069642-21392-1-git-send-email-spanda@codeaurora.org
|
|
Add a driver for Cadence DPI -> DSI bridge.
This driver only support a subset of Cadence DSI bridge capabilities.
This driver has been tested/debugged in a simulated environment which
explains why some of the features are missing. Here is a
non-exhaustive list of missing features:
* burst mode
* DPHY init/configuration steps
* support for additional input interfaces (SDI input)
DSI commands and non-burst video mode have been tested.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180421070846.10330-1-boris.brezillon@bootlin.com
|
|
Add DRM bridge driver for Thine THC63LVD1024 LVDS to digital parallel
output converter.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1524062429-325-3-git-send-email-jacopo+renesas@jmondi.org
|
|
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.15.
Core:
- Atomic object lifetime fixes
- Atomic iterator improvements
- Sparse/smatch fixes
- Legacy kms ioctls to be interruptible
- EDID override improvements
- fb/gem helper cleanups
- Simple outreachy patches
- Documentation improvements
- Fix dma-buf rcu races
- DRM mode object leasing for improving VR use cases.
- vgaarb improvements for non-x86 platforms.
New driver:
- tve200: Faraday Technology TVE200 block.
This "TV Encoder" encodes a ITU-T BT.656 stream and can be found in
the StorLink SL3516 (later Cortina Systems CS3516) as well as the
Grain Media GM8180.
New bridges:
- SiI9234 support
New panels:
- S6E63J0X03, OTM8009A, Seiko 43WVF1G, 7" rpi touch panel, Toshiba
LT089AC19000, Innolux AT043TN24
i915:
- Remove Coffeelake from alpha support
- Cannonlake workarounds
- Infoframe refactoring for DisplayPort
- VBT updates
- DisplayPort vswing/emph/buffer translation refactoring
- CCS fixes
- Restore GPU clock boost on missed vblanks
- Scatter list updates for userptr allocations
- Gen9+ transition watermarks
- Display IPC (Isochronous Priority Control)
- Private PAT management
- GVT: improved error handling and pci config sanitizing
- Execlist refactoring
- Transparent Huge Page support
- User defined priorities support
- HuC/GuC firmware refactoring
- DP MST fixes
- eDP power sequencing fixes
- Use RCU instead of stop_machine
- PSR state tracking support
- Eviction fixes
- BDW DP aux channel timeout fixes
- LSPCON fixes
- Cannonlake PLL fixes
amdgpu:
- Per VM BO support
- Powerplay cleanups
- CI powerplay support
- PASID mgr for kfd
- SR-IOV fixes
- initial GPU reset for vega10
- Prime mmap support
- TTM updates
- Clock query interface for Raven
- Fence to handle ioctl
- UVD encode ring support on Polaris
- Transparent huge page DMA support
- Compute LRU pipe tweaks
- BO flag to allow buffers to opt out of implicit sync
- CTX priority setting API
- VRAM lost infrastructure plumbing
qxl:
- fix flicker since atomic rework
amdkfd:
- Further improvements from internal AMD tree
- Usermode events
- Drop radeon support
nouveau:
- Pascal temperature sensor support
- Improved BAR2 handling
- MMU rework to support Pascal MMU
exynos:
- Improved HDMI/mixer support
- HDMI audio interface support
tegra:
- Prep work for tegra186
- Cleanup/fixes
msm:
- Preemption support for a5xx
- Display fixes for 8x96 (snapdragon 820)
- Async cursor plane fixes
- FW loading rework
- GPU debugging improvements
vc4:
- Prep for DSI panels
- fix T-format tiling scanout
- New madvise ioctl
Rockchip:
- LVDS support
omapdrm:
- omap4 HDMI CEC support
etnaviv:
- GPU performance counters groundwork
sun4i:
- refactor driver load + TCON backend
- HDMI improvements
- A31 support
- Misc fixes
udl:
- Probe/EDID read fixes.
tilcdc:
- Misc fixes.
pl111:
- Support more variants
adv7511:
- Improve EDID handling.
- HDMI CEC support
sii8620:
- Add remote control support"
* tag 'drm-for-v4.15' of git://people.freedesktop.org/~airlied/linux: (1480 commits)
drm/rockchip: analogix_dp: Use mutex rather than spinlock
drm/mode_object: fix documentation for object lookups.
drm/i915: Reorder context-close to avoid calling i915_vma_close() under RCU
drm/i915: Move init_clock_gating() back to where it was
drm/i915: Prune the reservation shared fence array
drm/i915: Idle the GPU before shinking everything
drm/i915: Lock llist_del_first() vs llist_del_all()
drm/i915: Calculate ironlake intermediate watermarks correctly, v2.
drm/i915: Disable lazy PPGTT page table optimization for vGPU
drm/i915/execlists: Remove the priority "optimisation"
drm/i915: Filter out spurious execlists context-switch interrupts
drm/amdgpu: use irq-safe lock for kiq->ring_lock
drm/amdgpu: bypass lru touch for KIQ ring submission
drm/amdgpu: Potential uninitialized variable in amdgpu_vm_update_directories()
drm/amdgpu: potential uninitialized variable in amdgpu_vce_ring_parse_cs()
drm/amd/powerplay: initialize a variable before using it
drm/amd/powerplay: suppress KASAN out of bounds warning in vega10_populate_all_memory_levels
drm/amd/amdgpu: fix evicted VRAM bo adjudgement condition
drm/vblank: Tune drm_crtc_accurate_vblank_count() WARN down to a debug
drm/rockchip: add CONFIG_OF dependency for lvds
...
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
SiI9234 transmitter converts eTMDS/HDMI signal to MHL 1.0.
It is controlled via I2C bus. Its interaction with other
devices in video pipeline is performed mainly on HW level.
The only interaction it does on device driver level is
filtering-out unsupported video modes, it exposes drm_bridge
interface to perform this operation.
This patch is based on the code refactored by Tomasz Stanislawski
<t.stanislaws@samsung.com>, which was initially developed by:
Adam Hampson <ahampson@sta.samsung.com>
Erik Gilling <konkers@android.com>
Shankar Bandal <shankar.b@samsung.com>
Dharam Kumar <dharam.kr@samsung.com>
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Acked-by: Rob Herring <robh@kernel.org> [for dt bindings]
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507212431-5801-2-git-send-email-m.purski@samsung.com
|
|
Include <drm/*.h> instead of relative path from include/drm, then
remove the -Iinclude/drm compiler flag.
While we are here, sort the touched parts alphabetically.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1493009447-31524-7-git-send-email-yamada.masahiro@socionext.com
|
|
The driver is already made of 5 separate source files. Move it to a
newly created directory named synopsys where more Synopsys bridge
drivers can be added later (for the DisplayPort controller for
instance).
Suggested-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303172007.26541-10-laurent.pinchart+renesas@ideasonboard.com
|
|
The LVDS encoder driver is a DRM bridge driver that supports the
parallel to LVDS encoders that don't require any configuration. The
driver thus doesn't interact with the device, but creates an LVDS
connector for the panel and exposes its size and timing based on
information retrieved from DT.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302104728.7150-3-laurent.pinchart+renesas@ideasonboard.com
|
|
The video processing pipeline on the second output on the GE B850v3:
Host -> LVDS|--(STDP4028)--|DP -> DP|--(STDP2690)--|DP++ -> Video output
Each bridge has a dedicated flash containing firmware for supporting the
custom design. The result is that in this design neither the STDP4028
nor the STDP2690 behave as the stock bridges would. The compatible
strings include the suffix "-ge-b850v3-fw" to make it clear that the
driver is for the bridges with the firmware which is specific for the GE
B850v3.
The driver is powerless to control the video processing pipeline, as the
two bridges behaves as a single one. The driver is only needed for
telling the host about EDID / HPD, and for giving the host powers to ack
interrupts.
This driver adds one i2c_device for each bridge, but only one
drm_bridge. This design allows the creation of a functional connector
that is capable of reading EDID from the STDP2690 while handling
interrupts on the STDP4028.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Enric Balletbo <enric.balletbo@collabora.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/ad92919f2eaff2623a551aac94cf11ef948ff9ee.1488555615.git.peter.senna@collabora.com
|
|
tilcdc changes for v4.10
* tag 'tilcdc-4.10' of https://github.com/jsarha/linux: (23 commits)
drm/tilcdc: fix parsing of some DT properties
drm/tilcdc: Enable frame done irq and functionality for LCDC rev 1
drm/tilcdc: Configure video mode to HW in enable() not in mode_set_nofb()
drm/tilcdc: Load palette at the end of mode_set_nofb()
drm/tilcdc: Add timeout wait for palette loading to complete
drm/tilcdc: Enable palette loading for revision 2 LCDC too
drm/tilcdc: Fix load mode bit-field setting in tilcdc_crtc_enable()
drm/tilcdc: Add tilcdc_write_mask() to tilcdc_regs.h
drm/tilcdc: Fix tilcdc_crtc_create() return value handling
drm/tilcdc: implement palette loading for rev1
drm/tilcdc: Enable sync lost error and recovery handling for rev 1 LCDC
drm/tilcdc: Add drm bridge support for attaching drm bridge drivers
drm/bridge: Add ti-tfp410 DVI transmitter driver
dt-bindings: Move "ti,tfp410.txt" from display/ti to display/bridge
drm/tilcdc: Recover from sync lost error flood by resetting the LCDC
drm/tilcdc: Fix race from forced shutdown of crtc in unload
drm/tilcdc: Use unload to handle initialization failures
drm/tilcdc: Stop using struct drm_driver load() callback
drm/tilcdc: Remove obsolete drm_connector_register() calls
drm/tilcdc: Correct misspelling in error message
...
|
|
Add very basic ti-tfp410 DVI transmitter driver. The only feature
separating this from a completely dummy bridge is the EDID read
support trough DDC I2C. Even that functionality should be in a
separate generic connector driver. However, because of missing DRM
infrastructure support the connector is implemented within the bridge
driver. Some tfp410 HW specific features may be added later if needed,
because there is a set of registers behind i2c if it is connected.
This implementation is tested against my new tilcdc bridge support
and it works with BeagleBone DVI-D Cape Rev A3. A DT binding document
is also updated.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
|
|
Current dw-hdmi is supporting sound via AHB bus, but it has
I2S audio feature too. This patch adds I2S audio support to dw-hdmi.
This HDMI I2S is supported by using ALSA SoC common HDMI encoder
driver.
Tested-by: Jose Abreu <joabreu@synopsys.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/8737j2bxba.wl%kuninori.morimoto.gx@renesas.com
|
|
SiI8620 transmitter converts eTMDS/HDMI signal to MHL 3.0.
It is controlled via I2C bus. Its interaction with other
devices in video pipeline is performed mainly on HW level.
The only interaction it does on device driver level is
filtering-out unsupported video modes, it exposes drm_bridge
interface to perform this operation.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1476085157-5266-1-git-send-email-a.hajda@samsung.com
|
|
Some boards have an entirely passive RGB to VGA bridge, based on DACs
implemented by resistor ladders.
Those might or might not have an i2c bus routed to the VGA connector in
order to access the screen EDIDs.
Add a bridge that doesn't do anything but expose the modes available on the
screen, either based on the EDIDs if available, or based on the XGA
standards.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20160930143709.1388-3-maxime.ripard@free-electrons.com
|
|
Add a drm_bridge driver for the Toshiba TC358767 DPI/DSI to
eDP/DP bridge. Currently only DPI input with 24-bit RGB is
supported.
Signed-off-by: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
|
|
The driver has been converted to use drm_bridge instead of
drm_i2c_slave_encoder. We can now move it to the bridge folder.
Create a separate folder since we already have a couple of files and
expect more when we support audio and ADV7533.
Rename the driver to adv7511_drv.c. This will come in handy later
when the driver module will need to be built from multiple object
files.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
|
|
Add basic support for the sii902x RGB -> HDMI bridge.
This driver does not support audio output yet.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
---
Changes in v8:
- remove useless headers inclusion
- fix macro names (s/SIL/SII)
- drop unneeded hotplug_work field from struct sii902x
- drop drm_connector_unregister() call in the ->destroy() method
- add a timeout when polling a register value
Changes in v6:
- use HDMI_INFOFRAME_SIZE(AVI)
- fix reset_gpio initialization
- reduce the reset time based on Ming feedback
Changes in v5:
- drop the best_encoder() implementation
Changes in v4:
- make reset GPIO optional
- only support attaching to DRM devices supporting atomic updates
Changes in v3:
- fix get_modes() implementation to avoid turning the screen in power
save mode
- rename the driver (sil902x -> sii902x)
Changes in v2:
- fix errors reported by the kbuild robot
fixup! drm: bridge: Add sii902x driver
|
