| Age | Commit message (Collapse) | Author |
|---|
|
Calling dma_sync_*() on a buffer from dma_alloc_coherent() is pointless.
The driver should not be doing its own bounce-buffering if the buffer is
allocated through dma_alloc_coherent().
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250710131206.2316-4-akhilrajeev@nvidia.com
|
|
For controllers that has an internal software reset, make the reset
property optional. This provides and option to use I2C in systems
that choose to restrict reset control from Linux or not to implement
the ACPI _RST method.
Internal reset was not required when the reset control was mandatory.
But on platforms where the resets are outside the control of Linux,
this had to be implemented by just returning success from BPMP or with
an empty _RST method in the ACPI table, basically ignoring the reset.
While the internal reset is not identical to the hard reset of the
controller, this will reset all the internal state of the controller
including FIFOs. This may slightly alter the behaviour in systems
which were ignoring the reset but it should not cause any functional
difference since all the required I2C registers are configured after
this reset, just as in boot. Considering that this sequence is hit
during the boot or during the I2C recovery path from an error, the
internal reset provides a better alternative than just ignoring the
reset.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250710131206.2316-3-akhilrajeev@nvidia.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"I2C Core:
- prevent double-free of an fwnode if it is a software node
- use recent helpers instead of custom ACPI or outdated OF ones
- add a more elaborate description of a message flag
Cleanups and refactorings:
- lpi2c, riic, st, stm32f7: general improvements
- riic: support more flexible IRQ configurations
- tegra: fix documentation
Improvements:
- lpi2c: improve register polling and add atomic transfer
- imx: use guarded spinlocks
New hardware support:
- Samsung Exynos 2200
- Renesas RZ/T2H (R9A09G077), RZ/N2H (R9A09G087)
DT binding:
- rk3x: enable power domains
- nxp: support clock property"
* tag 'i2c-for-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core: Fix double-free of fwnode in i2c_unregister_device()
i2c: lpi2c: implement xfer_atomic callback
i2c: lpi2c: use readl_poll_timeout() for register polling
dt-bindings: i2c: i2c-rk3x: Allow use of a power-domain
dt-bindings: i2c: exynos5: add samsung,exynos2200-hsi2c compatible
i2c: lpi2c: convert to use secs_to_jiffies()
i2c: st: Use min() to improve code
i2c: imx: use guard to take spinlock
i2c: stm32f7: Use str_on_off() helper
dt-bindings: i2c: nxp,pnx-i2c: allow clocks property
i2c: riic: Add support for RZ/T2H SoC
i2c: riic: Move generic compatible string to end of array
i2c: riic: Pass IRQ desc array as part of OF data
dt-bindings: i2c: renesas,riic: Document RZ/T2H and RZ/N2H support
dt-bindings: i2c: renesas,riic: Move ref for i2c-controller.yaml to the end
i2c: tegra: Add missing kernel-doc for dma_dev member
i2c: Clarify behavior of I2C_M_RD flag
i2c: mux: pca954x: Use dev_fwnode()
i2c: acpi: Replace custom code with device_match_acpi_handle()
|
|
The acpi_evaluate_object() returns an ACPI error code and not
Linux one. For the some platforms the err will have positive code
which may be interpreted incorrectly. Use device_reset() for
reset control which handles it correctly.
Fixes: bd2fdedbf2ba ("i2c: tegra: Add the ACPI support")
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Cc: <stable@vger.kernel.org> # v5.17+
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250710131206.2316-2-akhilrajeev@nvidia.com
|
|
Fix the kernel-doc warning by describing the 'dma_dev' member in
the tegra_i2c_dev struct. This resolves the compilation warning:
drivers/i2c/busses/i2c-tegra.c:297: warning: Function parameter or struct member 'dma_dev' not described in 'tegra_i2c_dev'
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250522163814.399630-1-18255117159@163.com
|
|
Convert the I2C subsystem to drop using the 'master_'-prefixed callbacks
in favor of the simplified ones. Fix alignment of '=' while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
For SMBUS block read, do not continue to read if the message length
passed from the device is '0' or greater than the maximum allowed bytes.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20250424053320.19211-1-akhilrajeev@nvidia.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/i2c to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
On ACPI machines, the tegra i2c module encounters an issue due to a
mutex being called inside a spinlock. This leads to the following bug:
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:585
...
Call trace:
__might_sleep
__mutex_lock_common
mutex_lock_nested
acpi_subsys_runtime_resume
rpm_resume
tegra_i2c_xfer
The problem arises because during __pm_runtime_resume(), the spinlock
&dev->power.lock is acquired before rpm_resume() is called. Later,
rpm_resume() invokes acpi_subsys_runtime_resume(), which relies on
mutexes, triggering the error.
To address this issue, devices on ACPI are now marked as not IRQ-safe,
considering the dependency of acpi_subsys_runtime_resume() on mutexes.
Fixes: bd2fdedbf2ba ("i2c: tegra: Add the ACPI support")
Cc: <stable@vger.kernel.org> # v5.17+
Co-developed-by: Michael van der Westhuizen <rmikey@meta.com>
Signed-off-by: Michael van der Westhuizen <rmikey@meta.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
I2C and SMBus timeouts are not something the user needs to be informed
about on controller level. The client driver may know if that really is
a problem and give more detailed information to the user. The controller
should just pass this information upwards. Remove the printout.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"I2C has mainly cleanups this time and a few driver improvements.
Because a lot of developers were on holidays (including myself) it was
a good timing to apply lots of cleanups which would normally cause
merge conflicts with other floating patches. Extra thanks go to Andi
Shyti who backed me up when I was on a four week hiatus. This is also
the reason that some patches were commited later than ideal"
* tag 'i2c-for-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (67 commits)
i2c: at91: Use dev_err_probe() instead of dev_err()
I2C: ali15x3: Do PCI error checks on own line
i2c: Make return value check more accurate and explicit for devm_pinctrl_get()
i2c: designware: Add support for recovery when GPIO need pinctrl
i2c: mlxcpld: Add support for extended transaction length
i2c: mlxcpld: Allow driver to run on ARM64 architecture
i2c: nforce2: Do PCI error check on own line
i2c: sis5595: Do PCI error checks on own line
i2c: qcom-cci: Fix error checking in cci_probe()
i2c: muxes: pca954x: Add regulator support
i2c: muxes: pca954x: Add MAX735x/MAX736x support
dt-bindings: i2c: Add Maxim MAX735x/MAX736x variants
dt-bindings: i2c: pca954x: Correct interrupt support
i2c: pnx: Use devm_platform_get_and_ioremap_resource()
i2c: pxa: Use devm_platform_get_and_ioremap_resource()
i2c: s3c2410: Use devm_platform_get_and_ioremap_resource()
i2c: sh_mobile: Use devm_platform_get_and_ioremap_resource()
i2c: st: Use devm_platform_get_and_ioremap_resource()
i2c: qcom-geni: Convert to devm_platform_ioremap_resource()
i2c: stm32f4: Use devm_platform_get_and_ioremap_resource()
...
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Tegra processors prior to Tegra186 used APB DMA for I2C requiring
CONFIG_TEGRA20_APB_DMA=y while Tegra186 and later use GPC DMA requiring
CONFIG_TEGRA186_GPC_DMA=y.
The check for if the processor uses APB DMA is inverted and so the wrong
DMA config options are checked.
This means if CONFIG_TEGRA20_APB_DMA=y but CONFIG_TEGRA186_GPC_DMA=n
with a Tegra186 or later processor the driver will incorrectly think DMA is
enabled and attempt to request DMA channels that will never be availible,
leaving the driver in a perpetual EPROBE_DEFER state.
Fixes: 48cb6356fae1 ("i2c: tegra: Add GPCDMA support")
Signed-off-by: Parker Newman <pnewman@connecttech.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Akhil R <akhilrajeev@nvidia.com>
Link: https://lore.kernel.org/r/fcfcf9b3-c8c4-9b34-2ff8-cd60a3d490bd@connecttech.com
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
If the driver fails to obtain a DMA channel, it will initiate cleanup
and try to release the DMA channel that couldn't be retrieved. This will
cause a crash because the cleanup will try to dereference an ERR_PTR()-
encoded error code.
However, there's nothing to clean up at this point yet, so we can avoid
this by simply resetting the DMA channel to NULL instead of storing the
error code.
Fixes: fcc8a89a1c83 ("i2c: tegra: Share same DMA channel for RX and TX")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Save a bit of code for older Tegra platforms by compiling out
VI's I2C mode support that's used only for Tegra210.
$ size i2c-tegra.o
text data bss dec hex filename
11381 292 8 11681 2da1 i2c-tegra.o (full)
10193 292 8 10493 28fd i2c-tegra.o (no-dvc)
9145 292 8 9445 24e5 i2c-tegra.o (no-vi,no-dvc)
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Save a bit of code for newer Tegra platforms by compiling out
DVC's I2C mode support that's used only for Tegra2.
$ size i2c-tegra.o
text data bss dec hex filename
- 11381 292 8 11681 2da1 i2c-tegra.o
+ 10193 292 8 10493 28fd i2c-tegra.o
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Allocate only one DMA channel for I2C and share it for both TX and RX
instead of using two different DMA hardware channels with the same
slave ID. Since I2C supports only half duplex, there is no impact on
perf with this.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Alain Volmat <alain.volmat@foss.st.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Asmaa Mnebhi <asnaa@nvidia.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Chris Pringle <chris.pringle@phabrix.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Tali Perry <tali.perry@nuvoton.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Update the msg->len value correctly for SMBUS block read. The discrepancy
went unnoticed as msg->len is used in SMBUS transfers only when a PEC
byte is added.
Fixes: d7583c8a5748 ("i2c: tegra: Add SMBus block read function")
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"Core got a new helper 'i2c_client_get_device_id()', designware got
some bigger updates, the rest is driver updates all over the place"
* tag 'i2c-for-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (41 commits)
i2c: ismt: Fix an out-of-bounds bug in ismt_access()
i2c: mux: reg: check return value after calling platform_get_resource()
i2c: xiic: Make sure to disable clock on .remove()
i2c: hisi: Add support to get clock frequency from clock
i2c: pxa-pci: fix missing pci_disable_device() on error in ce4100_i2c_probe
i2c: slave-eeprom: Convert to i2c's .probe_new()
i2c: mux: pca954x: Convert to i2c's .probe_new()
drivers/i2c: use simple i2c probe
i2c: mux: pca9541: switch to using .probe_new
i2c: gpio: Fix potential unused warning for 'i2c_gpio_dt_ids'
i2c: qcom-geni: add support for I2C Master Hub variant
i2c: qcom-geni: add desc struct to prepare support for I2C Master Hub variant
soc: qcom: geni-se: add support for I2C Master Hub wrapper variant
soc: qcom: geni-se: add desc struct to specify clocks from device match data
dt-bindings: i2c: qcom-geni: document I2C Master Hub serial I2C engine
dt-bindings: qcom: geni-se: document I2C Master Hub wrapper variant
dt-bindings: i2c: renesas,riic: Document RZ/Five SoC
i2c: tegra: Set ACPI node as primary fwnode
i2c: smbus: add DDR support for SPD
i2c: /pasemi: PASemi I2C controller IRQ enablement
...
|
|
Set ACPI node as the primary fwnode of I2C adapter to allow
enumeration of child devices from the ACPI table
Signed-off-by: Zubair Waheed <zwaheed@nvidia.com>
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
When the I2C controllers are running in DMA mode, it is the DMA engine
that performs the memory accesses rather than the I2C controller. Pass
the DMA engine's struct device pointer to the DMA API to make sure the
correct DMA operations are used.
This fixes an issue where the DMA engine's SMMU stream ID needs to be
misleadingly set for the I2C controllers in device tree.
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Enable support for GPCDMA, which is used in I2C controllers
in Tegra 186 and above. The chips before that used APB DMA.
This change works under the presumption that all chips apart from
those supporting APB DMA is using GPCDMA.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Follow the advice of the below link and prefer 'strscpy'. Conversion is
easy because no driver used the return value and has been done with a
simple sed invocation.
Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Emulate SMBus block read using ContinueXfer to read the length byte
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Use i2c_timings struct and corresponding methods to get bus clock frequency
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Add support for the ACPI based device registration so that the driver
can be also enabled through ACPI table.
This does not include the ACPI support for Tegra VI and DVC I2C.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Tegra I2C device isn't guaranteed to be suspended after removal of
the driver since driver uses pm_runtime_put() that is asynchronous and
pm_runtime_disable() cancels pending power-change requests. This means
that potentially refcount of the clocks may become unbalanced after
removal of the driver. This a very minor problem which unlikely to
happen in practice and won't cause any visible problems, nevertheless
let's replace pm_runtime_disable() with pm_runtime_force_suspend() and
use pm_runtime_put_sync() which disables RPM of the device and puts it
into suspend before driver is removed.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Switch to use threaded interrupt context in order to avoid checking of
"are we in interrupt?" for the code that may sleep in the IRQ handler.
I2C doesn't require a very low interrupt-handling latency, hence this
change doesn't introduce any noticeable effects.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
VI I2C controller has known hardware bug where immediate multiple
writes to TX_FIFO register gets stuck.
Recommended software work around is to read I2C register after
each write to TX_FIFO register to flush out the data.
This patch implements this work around for VI I2C controller.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Upon a communication error, the interrupt handler can call
tegra_i2c_disable_packet_mode. This causes a sleeping poll to happen
unless the current transaction was marked atomic. Fix this by
making the poll happen atomically if we are in an IRQ.
This matches the behavior prior to the patch mentioned
in the Fixes tag.
Fixes: ede2299f7101 ("i2c: tegra: Support atomic transfers")
Cc: stable@vger.kernel.org
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Use proper spelling of "NVIDIA" and don't designate driver as Tegra2-only
since newer SoC generations are supported as well.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Some places in the code are missing newlines or have unnecessary
whitespaces and newlines. This creates inconsistency of the code and
hurts readability. This patch removes the unnecessary and adds necessary
whitespaces / newlines, clears indentation of the code.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Make all comments to be consistent in regards to capitalization and
punctuation, correct spelling and grammar errors, improve wording.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
This patch unifies style of all messages in the driver by starting them
with a lowercase letter and using consistent capitalization and wording
for all messages.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Rename "ret" variables to "err" in order to make code a bit more
expressive, emphasizing that the returned value is an error code.
Same vice versa, where appropriate.
Rename variable "reg" to "val" in order to better reflect the actual
usage of the variable in the code and to make naming consistent with
the rest of the code.
Use briefer names for a few members of the tegra_i2c_dev structure in
order to improve readability of the code.
All dev/&pdev->dev are replaced with i2c_dev->dev in order to have uniform
code style across the driver.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Reorder definition of variables in the code to have them sorted by length
and grouped logically, also replace "unsigned long" with "u32". Do this in
order to make code easier to read.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The driver's code is inconsistent in regards to the error values checking.
The correct way should be to check both positive and negative values.
This patch cleans up the error-checks in the code. Note that the
pm_runtime_get_sync() could return positive value on success, hence only
relevant parts of the code are changed by this patch.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Factor out hardware initialization into a separate function from the probe
function. The only place where runtime PM needs to be resumed during probe
is the place of hardware initialization, hence it makes sense to factor
out it in order to have a bit cleaner error handling in tegra_i2c_probe().
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Factor out register polling into a separate function in order to remove
boilerplate code and make code cleaner.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The code related to packet header setting up is a bit messy and makes
tegra_i2c_xfer_msg() more difficult to read than it could be. Let's
factor the packet header setup from tegra_i2c_xfer_msg() into separate
function in order to make code easier to read and follow.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Factor out error recovery code from tegra_i2c_xfer_msg() in order to
make this function easier to read and follow.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Drop '_timeout' postfix from the wait/poll completion function names in
order to make the names shorter, making code cleaner a tad.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The "dma" variable of tegra_i2c_xfer_msg() function doesn't bring much in
regards to readability and generation of the code.
Besides readability, it's also not very nice that the is_curr_dma_xfer
is initialized in tegra_i2c_xfer_msg() and then could be overridden by
tegra_i2c_config_fifo_trig(). In a result, the "dma" variable creates
slight confusion since it's not instantly obvious why it's set after
tegra_i2c_config_fifo_trig().
Hence should be better to have the variable removed. This makes code
more consistent.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The tegra_i2c_wait_for_config_load() checks for 'has_config_load_reg' by
itself, hence there is no need to duplicate the check.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The likely/unlikely annotations should be used only in a hot paths of
performance-critical code. The I2C driver doesn't have such paths, and
thus, there is no justification for usage of likely/unlikely annotations
in the code. Hence remove them.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The barrier() was intended to reduce possibility of racing with the
interrupt handler, but driver's code evolved significantly and today's
driver enables interrupt only when it waits for completion notification.
Hence barrier() has no good use anymore, let's remove it.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Don't use signed types for unsigned values and use consistent types
for sibling variables.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Reorder location of functions in the code in order to have definition
of functions closer to the place of the invocation. This change makes
easier to navigate around the code and removes the need to have a
prototype for tegra_i2c_init().
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The driver's probe function code is a bit difficult to read. This patch
reorders code of the probe function, forming groups of code that are easy
to work with. The probe tear-down order now matches the driver-removal
order.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
