| Age | Commit message (Collapse) | Author |
|---|
|
Disable IBI IRQ signal and status only when hot-join and SIR enabling of
all target devices attached to the bus are disabled.
Fixes: e389b1d72a62 ("i3c: dw: Add support for in-band interrupts")
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Link: https://lore.kernel.org/r/20240119054547.983693-1-dylan_hung@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
As per the Cadence IP document fixed the I2C clock divider value limit from
16 bits instead of 10 bits. Without this change setting up the I2C clock to
low frequencies will not work as the prescaler value might be greater than
10 bit number.
I3C clock divider value is 10 bits only. Updating the macro names for both.
Signed-off-by: Harshit Shah <harshitshah.opendev@gmail.com>
Link: https://lore.kernel.org/r/1703927483-28682-1-git-send-email-harshitshah.opendev@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
I3C allow devices early terminate data transfer. So set "actual_len" to
indicate how much data get by i3c_priv_xfer.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231201222532.2431484-6-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
I3C transfer (SDR), target can early terminate read transfer.
I3C transfer (HDR), target can end write transfer.
I2C transfer, target can NACK write transfer.
'actual_len' is better name than 'read_len'.
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231201222532.2431484-5-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add hot join support for svc master controller. Disable hot join by
default.
User can use sysfs entry to enable hot join.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231201222532.2431484-3-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Implement a local bounce buffer for private I3C SDR and I2C transfers
when using DMA and the buffer attached to the transfer is not DMA safe.
Otherwise the DMA transfer will fail and with following warning:
[ 11.411059] i3c mipi-i3c-hci.0: rejecting DMA map of vmalloc memory
[ 11.417313] WARNING: CPU: 3 PID: 357 at include/linux/dma-mapping.h:332 hci_dma_queue_xfer+0x2e2/0x300 [mipi_i3c_hci]
Strictly speaking private I3C SDR transfers are expected to pass a
DMA-able buffer. However I fear this requirement may easily be slipped
or go unnoticed when I3C interface support is added into a existing
device driver that use regmap API to read/write stack variables.
For example this is the case with the commit 2660b0080bb2 ("iio: imu:
st_lsm6dsx: add i3c basic support for LSM6DSO and LSM6DSR").
Buffer of an I2C message is not required to be DMA safe and the I2C core
provides i2c_(get|put)_dma_safe_msg_buf() helpers for the host
controllers that do DMA and that is also recommendation for the
i2c_xfers() callback from the I3C core.
However due to above I3C private transfers reason I decided to implement
a bounce buffer for them and reuse the same code for the I2C transfers
too. Since this driver is currently the only I3C host controller driver
that can do DMA the implementation is done here and not in I3C core.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20231109133708.653950-5-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Handle also I3C address header error response status as the end of DAA
process in hci_cmd_v1_daa().
According to MIPI I3C HCI Specification v1.1 the NACK error during DAA
process comes when the device does not accept the dynamic address.
Currently code uses it for successful exit from the process and fails
with any other error response.
I'm unsure is this MIPI I3C HCI version specific difference or
specification misunderstanding but on an early MIPI I3C HCI version
compatible controller responds always with I3C address header error and
not with NACK error when there is no device on the bus or no more devices
participating to DAA process.
Handle now both response statuses as the end of DAA.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20231109133708.653950-4-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Function hci_cmd_v1_daa() uses only single transfer at a time so no need
to allocate two transfers and access can be simplified.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20231109133708.653950-3-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Currently probe of mipi-i3c-hci will fail if bus doesn't have any I3C
devices connected. This happens when CCC commands that are sent during
i3c_master_bus_init() are not ACKed by any device and controller responds
with an error status set.
The controller can detect NACK both during I3C address header
transmission (broadcast address 0x7e is not ACKed) and when target
device address or dynamic address assignment is NACKed. Former as error
status 0x4: Address Header Error and latter as 0x5: NACK.
Difference between those two NACK statuses were not described explicitly
until MIPI I3C HCI Specification v1.1. Earlier versions share the same
error status code though.
Report both of those as I3C_ERROR_M2 to I3C core code.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20231109133708.653950-2-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The `i3c_master_bus_init` function may attach the I2C devices before the
I3C bus initialization. In this flow, the DAT `alloc_entry`` will be used
before the DAT `init`. Additionally, if the `i3c_master_bus_init` fails,
the DAT `cleanup` will execute before the device is detached, which will
execue DAT `free_entry` function. The above scenario can cause the driver
to use DAT_data when it is NULL.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20231023080237.560936-1-billy_tsai@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
In the binding documentation, the compatible string is specified as
'silvaco,i3c-master-v1', but in the driver, it is defined as
'silvaco,i3c-master'.
Rename 'silvaco,i3c-master' to 'silvaco,i3c-master-v1' to ensure
compatibility with the documentation.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231017194657.3199749-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
master side report:
silvaco-i3c-master 44330000.i3c-master: Error condition: MSTATUS 0x020090c7, MERRWARN 0x00100000
BIT 20: TIMEOUT error
The module has stalled too long in a frame. This happens when:
- The TX FIFO or RX FIFO is not handled and the bus is stuck in the
middle of a message,
- No STOP was issued and between messages,
- IBI manual is used and no decision was made.
The maximum stall period is 100 μs.
This can be considered as being just a warning as the system IRQ latency
can easily be greater than 100us.
Fixes: dd3c52846d59 ("i3c: master: svc: Add Silvaco I3C master driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20231023161658.3890811-7-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Upon IBIWON timeout, the SDA line will always be kept low if we don't emit
a stop. Calling svc_i3c_master_emit_stop() there will let the bus return to
idle state.
Fixes: dd3c52846d59 ("i3c: master: svc: Add Silvaco I3C master driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231023161658.3890811-6-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
svc_i3c_master_irq_handler() wrongly checks register SVC_I3C_MINTMASKED. It
should be SVC_I3C_MSTATUS.
Fixes: dd3c52846d59 ("i3c: master: svc: Add Silvaco I3C master driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231023161658.3890811-5-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
MSTATUS[RXPEND] is only updated after the data transfer cycle started. This
creates an issue when the I3C clock is slow, and the CPU is running fast
enough that MSTATUS[RXPEND] may not be updated when the code reaches
checking point. As a result, mandatory data can be missed.
Add a wait for MSTATUS[COMPLETE] to ensure that all mandatory data is
already in FIFO. It also works without mandatory data.
Fixes: dd3c52846d59 ("i3c: master: svc: Add Silvaco I3C master driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231023161658.3890811-4-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
┌─────┐ ┏──┐ ┏──┐ ┏──┐ ┏──┐ ┏──┐ ┏──┐ ┏──┐ ┏──┐ ┌─────
SCL: ┘ └─────┛ └──┛ └──┛ └──┛ └──┛ └──┛ └──┛ └──┛ └──┘
───┐ ┌─────┐ ┌─────┐ ┌───────────┐
SDA: └───────────────────────┘ └─────┘ └─────┘ └─────
xxx╱ ╲╱ ╲╱ ╲╱ ╲╱ ╲
: xxx╲IBI ╱╲ Addr(0x0a) ╱╲ RW ╱╲NACK╱╲ S ╱
If an In-Band Interrupt (IBI) occurs and IBI work thread is not immediately
scheduled, when svc_i3c_master_priv_xfers() initiates the I3C transfer and
attempts to send address 0x7e, the target interprets it as an
IBI handler and returns the target address 0x0a.
However, svc_i3c_master_priv_xfers() does not handle this case and proceeds
with other transfers, resulting in incorrect data being returned.
Add IBIWON check in svc_i3c_master_xfer(). In case this situation occurs,
return a failure to the driver.
Fixes: dd3c52846d59 ("i3c: master: svc: Add Silvaco I3C master driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231023161658.3890811-3-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The ibi work thread operates asynchronously with other transfers, such as
svc_i3c_master_priv_xfers(). Introduce mutex protection to ensure the
completion of the entire i3c/i2c transaction.
Fixes: dd3c52846d59 ("i3c: master: svc: Add Silvaco I3C master driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20231023161658.3890811-2-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The MIPI I3C spec refers to a Provisioned ID, since it is (sometimes)
provisioned at device manufacturing.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20231003075339.197099-1-matt@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Host Controller goes to halt state after aborted transfer and needs to
be resumed by SW. Add this resuming to DMA mode code too.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-13-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
On an HW I'm using in enabling work the RESUME bit is not set in the
HC_CONTROLLER register when Host Controller goes to halt state. Value 1
should mean controller is suspended when reading and writing 1 resumes it.
Because of this erratic behaviour plain HC_CONTROL read and write back
won't resume the controller. Therefore do it by setting the RESUME bit
explicitly.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-12-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Due to missing completion object for the ENTDAA command transfer in the
hci_cmd_v1_daa() the wait_for_completion_timeout() will obviously
timeout even the transfer itself may succeed.
Fix this by setting the xfer->completion to the already initialized
completion object.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-11-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Fix following warning (with CONFIG_DMA_API_DEBUG) which happens with a
transfer without a data buffer.
DMA-API: i3c mipi-i3c-hci.0: device driver tries to free DMA memory it has not allocated [device address=0x0000000000000000] [size=0 bytes]
For those transfers the hci_dma_queue_xfer() doesn't create a mapping and
the DMA address pointer xfer->data_dma is not set.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-10-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Number of software enabled Ring Bundles must be set before using them.
Otherwise Ring will not start and may be power-gated by the Host
Controller.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-9-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
If there is a transfer error during i3c_master_bus_init() and code goes
doing the bus cleanup in i3c_hci_bus_cleanup() there is possibility that
i3c_hci_irq_handler() is running in parallel with hci->io->cleanup()
which can be racy.
Prevent this by waiting there is no pending interrupt on other CPU
before doing the IO cleanup.
This was observed with ring headers where first transfer failed and
sometimes transfer error or ring transfer abort interrupt was coming
simultaneously with the bus cleanup path.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-8-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Set ring start request together with ring enable in hci_dma_init(). This
causes the ring abort request in hci_dma_dequeue_xfer() will raise the
INTR_RING_OP (RING_OP_STAT in MIPI I3C HCI specification) interrupt in
the RH_INTR_STATUS register.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-7-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Ring Abort request will timeout in case there is an error in the Host
Controller interrupt delivery or Ring Header configuration. Using BUG()
makes hard to debug those cases.
Make it less severe and turn BUG() to WARN_ON().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-6-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Do not loop over ring headers in hci_dma_irq_handler() that are not
allocated and enabled in hci_dma_init(). Otherwise out of bounds access
will occur from rings->headers[i] access when i >= number of allocated
ring headers.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-5-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
MIPI I3C HCI specification v1.1 describes the ENTRY_SIZE field for the
Device Address Table (DAT) and the Device Characteristics Table (DCT)
section offset registers (DAT_SECTION_OFFSET and DCT_SECTION_OFFSET).
That field is not documented in earlier version.
ENTRY_SIZE value 0 is meant to be backward compatible. For the DAT entry
size it is interpreted as 2 DWORDs (8-bytes) and for the DCT entry size
as 4 DWORDs (16-bytes). Values 1-15 are reserved for future use.
New version I believe fixes also the TABLE_SIZE field description.
Before it was defined in DWORDs which I believe is incorrect since the
DAT/DCT table entry structures, and sizes, are described having
8-bytes/16-bytes entries.
This is more clear in the specification v1.1 which states the TABLE_SIZE
fields are interpreted as number of entries in the DAT/DCT tables. I
believe this same holds also in earlier version, at least it makes more
sense.
Fix code accordingly and let the DAT_entry_size and the DCT_entry_size
variables carry the size as bytes. Which is how it is already
interpreted in the dat_v1.c: hci_dat_v1_init().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-4-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add MODULE_ALIAS() in order to be able to autoload this driver when the
device is added as a platform device from another glue code driver.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20230921055704.1087277-3-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct svc_i3c_xfer.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Conor Culhane <conor.culhane@silvaco.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: linux-i3c@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230922175023.work.239-kees@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct hci_rings_data.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Nicolas Pitre <npitre@baylibre.com>
Cc: Len Baker <len.baker@gmx.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: linux-i3c@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230922175019.work.129-kees@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct cdns_i3c_xfer.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: "Przemysław Gaj" <pgaj@cadence.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: linux-i3c@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230922175014.work.637-kees@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct dw_i3c_xfer.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Jeremy Kerr <jk@codeconstruct.com.au>
Cc: Joel Stanley <joel@jms.id.au>
Cc: linux-i3c@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20230922175011.work.800-kees@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
IBIR_DEPTH and CMDR_DEPTH should read from status0 instead of status1.
Cc: stable@vger.kernel.org
Fixes: 603f2bee2c54 ("i3c: master: Add driver for Cadence IP")
Signed-off-by: Joshua Yeong <joshua.yeong@starfivetech.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230913031743.11439-2-joshua.yeong@starfivetech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
I3C masters are expected to support hot-join. This means at initialization
time we might not yet discover any device and this should not be treated
as a fatal error.
During the DAA procedure which happens at probe time, if no device has
joined, all CCC will be NACKed (from a bus perspective). This leads to an
early return with an error code which fails the probe of the master.
Let's avoid this by just telling the core through an I3C_ERROR_M2
return command code that no device was discovered, which is a valid
situation. This way the master will no longer bail out and fail to probe
for a wrong reason.
Cc: stable@vger.kernel.org
Fixes: dd3c52846d59 ("i3c: master: svc: Add Silvaco I3C master driver")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230831141324.2841525-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The 'saved_regs' member of the 'svc_i3c_master' structure is not
described in the kernel doc, which produces the following warning:
Function parameter or member 'saved_regs' not described in 'svc_i3c_master'
Add the missing line in the kernel documentation of the parent
structure.
Fixes: 1c5ee2a77b1b ("i3c: master: svc: fix i3c suspend/resume issue")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202308171435.0xQ82lvu-lkp@intel.com/
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230817101853.16805-1-miquel.raynal@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
It is not possible for platform_get_irq() to return 0. Use the
return value from platform_get_irq().
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230803085149.149248-1-ruanjinjie@huawei.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The exit criteria for the DAA should check if the data length is equal to
1, instead of checking if the response status is equal to 1.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20230802100909.2568215-1-billy_tsai@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20230714174623.4057784-1-robh@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add NACK check after start byte is sent.
It is possible to detect early that a device is not on the bus
and avoid invalid transmissions thereafter.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230517033030.3068085-3-xiaoning.wang@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
pm_runtime_resume_and_get() may call sleep(). It cannot be used in
svc_i3c_master_start_xfer_locked(), because it is in a spin lock.
Move the pm runtime operations to svc_i3c_master_enqueue_xfer().
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Fixes: 05be23ef78f7 ("i3c: master: svc: add runtime pm support")
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230517033030.3068085-2-xiaoning.wang@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
When system suspends, if i3c module is powered down, register
value will lose.
Need to save the key registers before system suspend.
So save these registers value in runtime pm suspend, and restore them
if these register's value is different with the saved values
when runtime pm resume.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230517033030.3068085-1-xiaoning.wang@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
smatch reports
drivers/i3c/master/ast2600-i3c-master.c:121:34: warning: symbol
'ast2600_i3c_ops' was not declared. Should it be static?
This variable is only used in its defining file, so it should be static.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20230429134601.2688558-1-trix@redhat.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The 2k register setting is zero, OR-ing it in doesn't parallel the 2k
and 750 ohm pullups. We need a separate value for the 545 ohm setting.
Reported-by: Lukwinski Zbigniew <zbigniew.lukwinski@linux.intel.com>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20230428001849.1775559-1-jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The ast2600 i3c hardware is capable of IBIs, but we need a workaround
for a hardware issue with the I3C state machine handling IBI payloads
of specific lengths when PEC is not enabled. To avoid this, we need to
unconditionally enable PECs, at the consquence of losing a byte of data
when the device does not send a PEC.
Enable IBIs on the ast2600 platform, including an implementation of the
PEC workaround, which prints a warning when triggered.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/ba923b96d6d129024c975e8a0472c5b2fcb3af32.1680161823.git.jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
On the AST2600 i3c controller, we'll need to apply a workaround for a
hardware issue with IBI payloads.
Introduce a platform hook to allow dw i3c platform implementations to
modify the DAT entry in IBI enable/disable to allow this workaround in a
future change.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/d5d76a8d2336d2a71886537f42e71d51db184df6.1680161823.git.jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
This change adds support for receiving and dequeueing i3c IBIs.
By setting struct dw_i3c_master->ibi_capable before probe, a platform
implementation can select the IBI-enabled version of the i3c_master_ops,
enabling the global IBI infrastrcture for that controller.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/79daeefd7ccb7c935d0c159149df21a6c9a73ffa.1680161823.git.jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
In an upcoming change, we will want to store additional data about the
devices we have in the data address table.
Change the type of the DAT entries into a struct, which currently just
has the address data.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/9dc0d9e2857e851a0cf04819df48e5d31921f83e.1680161823.git.jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
In a future change we'll want to read from the IBI FIFO too, so turn
dw_i3c_read_rx_fifo() into a generic read with the FIFO register as a
parameter.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/827204789583dd86addffb47ecaeab9d67cf95d5.1680161823.git.jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Now that we have platform-specific infrastructure for the dw i3c driver,
add platform support for the ASPEED AST2600 SoC.
The AST2600 has a small set of "i3c global" registers, providing
platform-level i3c configuration outside of the i3c core.
For the ast2600, we need a couple of extra setup operations:
- on probe: find the i3c global register set and parse the SDA pullup
resistor values
- on init: set the pullups accordingly, and set the i3c instance IDs
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20230331091501.3800299-4-jk@codeconstruct.com.au
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
