| Age | Commit message (Collapse) | Author |
|---|
|
There maybe a race when using dmaengine_terminate_all(). The predisable
routine may call iio_triggered_buffer_predisable() prior to a pending DMA
callback.
Adopt dmaengine_terminate_sync() to ensure there's no pending DMA request
before calling iio_triggered_buffer_predisable().
Fixes: 2763ea0585c9 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 5.4 cycle.
* adis16400
- Make sure to free memory on a few failure paths.
* adxl372
- Fix wrong fifo depth
- Fix wrong indexing of data from the fifo.
- Perform a reset at startup to avoid a problem with inconsistent state.
* axp288
- This is a fix for a fix. The original fix made sure we kept the
configuration from some firmwares to preserve a bias current.
Unfortunately it appears the previous behaviour was working around
a buggy firmware by overwriting the wrong value it had. Hence
a regression was seen.
* bmc150
- Fix the centre temperature. This was due to an error in one of the
datasheets.
* hx711
- Fix an issue where a badly timed interrupt could lead to a control
line being high long enough to put the device into a low power state.
* meson_sar_adc
- Fix a case where the irq was enabled before everything it uses was
allocated.
* st_lsm6dsx
- Ensure we don't set the sensor sensitivity to 0 as it will force
all readings to 0.
- Fix a wait time for the slave i2c controller when the accelerometer
is not enabled.
* stm32-adc
- Precursor for fix. Move a set of register definitions to a header.
- Fix a race when several ADCs are in use with some using interrupts
to control the dataflow and some using DMA.
* vcnl4000
- Fix a garbage of_match_table in which a string was passed instead
of the intended enum.
* tag 'iio-fixes-for-5.4a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: Fix an undefied reference error in noa1305_probe
iio: light: opt3001: fix mutex unlock race
iio: adc: ad799x: fix probe error handling
iio: light: add missing vcnl4040 of_compatible
iio: light: fix vcnl4000 devicetree hooks
iio: imu: st_lsm6dsx: fix waitime for st_lsm6dsx i2c controller
iio: adc: axp288: Override TS pin bias current for some models
iio: imu: adis16400: fix memory leak
iio: imu: adis16400: release allocated memory on failure
iio: adc: stm32-adc: fix a race when using several adcs with dma and irq
iio: adc: stm32-adc: move registers definitions
iio: accel: adxl372: Perform a reset at start up
iio: accel: adxl372: Fix push to buffers lost samples
iio: accel: adxl372: Fix/remove limitation for FIFO samples
iio: adc: hx711: fix bug in sampling of data
iio: fix center temperature of bmc150-accel-core
iio: imu: st_lsm6dsx: forbid 0 sensor sensitivity
iio: adc: meson_saradc: Fix memory allocation order
|
|
Since commit 0f7ddcc1bff1 ("iio:adc:ad799x: Write default config on probe
and reset alert status on probe") the error path is wrong since it
leaves the vref regulator on. Fix this by disabling both regulators.
Fixes: 0f7ddcc1bff1 ("iio:adc:ad799x: Write default config on probe and reset alert status on probe")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Since commit 9bcf15f75cac ("iio: adc: axp288: Fix TS-pin handling") we
preserve the bias current set by the firmware at boot. This fixes issues
we were seeing on various models, but it seems our old hardcoded 80ųA bias
current was working around a firmware bug on at least one model laptop.
In order to both have our cake and eat it, this commit adds a dmi based
list of models where we need to override the firmware set bias current and
adds the one model we now know needs this to it: The Lenovo Ideapad 100S
(11 inch version).
Fixes: 9bcf15f75cac ("iio: adc: axp288: Fix TS-pin handling")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=203829
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
End of conversion may be handled by using IRQ or DMA. There may be a
race when two conversions complete at the same time on several ADCs.
EOC can be read as 'set' for several ADCs, with:
- an ADC configured to use IRQs. EOCIE bit is set. The handler is normally
called in this case.
- an ADC configured to use DMA. EOCIE bit isn't set. EOC triggers the DMA
request instead. It's then automatically cleared by DMA read. But the
handler gets called due to status bit is temporarily set (IRQ triggered
by the other ADC).
So both EOC status bit in CSR and EOCIE control bit must be checked
before invoking the interrupt handler (e.g. call ISR only for
IRQ-enabled ADCs).
Fixes: 2763ea0585c9 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Move STM32 ADC registers definitions to common header.
This is precursor patch to:
- iio: adc: stm32-adc: fix a race when using several adcs with dma and irq
It keeps registers definitions as a whole block, to ease readability and
allow simple access path to EOC bits (readl) in stm32-adc-core driver.
Fixes: 2763ea0585c9 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Fix bug in sampling function hx711_cycle() when interrupt occures while
PD_SCK is high. If PD_SCK is high for at least 60 us power down mode of
the sensor is entered which in turn leads to a wrong measurement.
Switch off interrupts during a PD_SCK high period and move query of DOUT
to the latest point of time which is at the end of PD_SCK low period.
This bug exists in the driver since it's initial addition. The more
interrupts on the system the higher is the probability that it happens.
Fixes: c3b2fdd0ea7e ("iio: adc: hx711: Add IIO driver for AVIA HX711")
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO driver updates from Greg KH:
"Here is the big staging/iio driver update for 5.4-rc1.
Lots of churn here, with a few driver/filesystems moving out of
staging finally:
- erofs moved out of staging
- greybus core code moved out of staging
Along with that, a new filesytem has been added:
- extfat
to provide support for those devices requiring that filesystem (i.e.
transfer devices to/from windows systems or printers)
Other than that, there a number of new IIO drivers, and lots and lots
and lots of staging driver cleanups and minor fixes as people continue
to dig into those for easy changes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (453 commits)
Staging: gasket: Use temporaries to reduce line length.
Staging: octeon: Avoid several usecases of strcpy
staging: vhciq_core: replace snprintf with scnprintf
staging: wilc1000: avoid twice IRQ handler execution for each single interrupt
staging: wilc1000: remove unused interrupt status handling code
staging: fbtft: make several arrays static const, makes object smaller
staging: rtl8188eu: make two arrays static const, makes object smaller
staging: rtl8723bs: core: Remove Macro "IS_MAC_ADDRESS_BROADCAST"
dt-bindings: anybus-controller: move to staging/ tree
staging: emxx_udc: remove local TRUE/FALSE definition
staging: wilc1000: look for rtc_clk clock
staging: dt-bindings: wilc1000: add optional rtc_clk property
staging: nvec: make use of devm_platform_ioremap_resource
staging: exfat: drop unused function parameter
Staging: exfat: Avoid use of strcpy
staging: exfat: use integer constants
staging: exfat: cleanup spacing for casts
staging: exfat: cleanup spacing for operators
staging: rtl8723bs: hal: remove redundant variable n
staging: pi433: Fix typo in documentation
...
|
|
meson_saradc's irq handler uses priv->regmap so make sure that it is
allocated before the irq get enabled.
This also fixes crash when CONFIG_DEBUG_SHIRQ is enabled, as device
managed resources are freed in the inverted order they had been
allocated, priv->regmap was freed before the spurious fake irq that
CONFIG_DEBUG_SHIRQ adds called the handler.
Fixes: 3af109131b7eb8 ("iio: adc: meson-saradc: switch from polling to interrupt mode")
Reported-by: Elie Roudninski <xademax@gmail.com>
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Elie ROUDNINSKI <xademax@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of new device support, cleanups and features for IIO in the 5.4 cycle
Revised pull request to fix up a missing Signed-off-by and roll in
a fix in the lsm9ds1 support after I broke it when applying.
Revised again because the fix changed a hash meaning a fix
that previously followed it now had the wrong fixes tag.
A few fixes in here that could have gone a faster path but aren't quite
worth the rush for 5.3.
New device support
* ad7606
- Support the ad7606b which adds a software controlled mode alongside
the pin controlled only approach of the ad7606. Including dt-bindings.
* lsm6dsx
- Add support for the gyro and accelerometer part of the lsm9ds1 which is
a compound device also including a magnetometer (st_sensors driver).
Includes bindings and precursor rework of the driver.
Features
* ad7192
- Add support for low pass filter control.
- DT binding docs.
Cleanups and minor fixes
* MAINTAINERS
- Fix a typo in a path.
- Add entry for ad7606
* ad5380
- Fix a failure to dereference a pointer before atempting to assign the
value.
* ad7192
- Drop platform data as not used in mainline and we now have full DT bindings.
* ad7606
- YAML conversion for dt-bindings.
* adis16240
- Rework write_raw to make it more readable using GENMASK.
* adis16460
- Fix and issue with an unsigned variable holding potential negatives.
* cros_ec
- Fix missing default of calibration vector so that we get 'something'
before calibration is complete on a given axis.
* hid-sensors
- Use int_pow instead of opencoding.
* isl29501
- rename dt-binding docs to include renesas inline with other renesas parts
and general current convention.
* kxcjk1013
- Improve comments on the 'unusual' ACPI ids used to identify which sensor
is which in certain laptops.
* lsm6dsx
- Add one bit to the fifo status masks for a number of parts.
- Drop a reserved entry from the sensitivity values to tidy up interface.
- Use core conversion macro from G to m/s^2 for lsm9ds1 to make it easier
to relate to the datasheet and consistent with other parts supported.
* max1027
- Use device managed APIs to avoid manual error handling and cleanup.
* rfd77402
- Typo in Kconfig help.
* sc27xx
- Switch to polling mode from interrupts as interrupt handling typically
to slow for very short sleeps.
* st-sensors
- Fix some missing selects for regmap.
* tools
- Add a .gitignore containing the binary outputs.
* tag 'iio-for-5.4b-take3' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (27 commits)
iio: imu: st_lsm6dsx: rely on IIO_G_TO_M_S_2 for gain definition for LSM9DS1
iio: imu: st_lsm6dsx: remove invalid gain value for LSM9DS1
iio: cros_ec: set calibscale for 3d MEMS to unit vector
iio: dac: ad5380: fix incorrect assignment to val
iio: imu: st_lsm6dsx: Fix FIFO diff mask for tagged fifo
dt-bindings: iio: imu: st_lsm6dsx: add lsm9ds1 device bindings
iio: imu: st_lsm6dsx: add support for accel/gyro unit of lsm9ds1
iio: imu: st_lsm6dsx: move register definitions to sensor_settings struct
iio: imu: st_lsm6dsx: introduce update_fifo function pointer
dt-bindings: iio: light: isl29501: Rename bindings documentation file
Kconfig: Fix the reference to the RFD77402 ToF sensor in the 'help' section
iio: st_sensors: Fix build error
dt-bindings: iio: adc: Add AD7606B ADC documentation
dt-bindings: iio: adc: Migrate AD7606 documentation to yaml
MAINTAINERS: Add Beniamin Bia for AD7606 driver
iio: adc: ad7606: Add support for AD7606B ADC
tools: iio: add .gitignore
iio: adc: sc27xx: Change to polling mode to read data
iio: hid-sensor-attributes: Convert to use int_pow()
iio: adc: max1027: Use device-managed APIs
...
|
|
A driver for ADS1015 with more functionality is available in the iio
subsystem.
Remove the hwmon driver as duplicate. If the chip is used for hardware
monitoring, the iio->hwmon bridge should be used.
Cc: Dirk Eibach <eibach@gdsys.de>
Link: https://lore.kernel.org/r/1562004758-13025-1-git-send-email-linux@roeck-us.net
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The AD7606B is a 16-bit ADC that supports simultaneous sampling of 8
channels. It is pin compatible to AD7606, but adds extra modes by
writing to the register map.
The AD7606B can be configured to work in software mode by setting all
oversampling pins to high. This mode is selected by default.
The oversampling ratio is configured from the OS_MODE register (address
0x08) with the addition of OS=128 and OS=256 that were not available in
hardware mode.
The device is configured to output data on a single spi channel, but this
configuration must be done right after restart. That is why the delay was
removed for devices which doesn't require it.
Moreover, in software mode, the range gpio has no longer its function.
Instead, the scale can be configured individually for each channel from
the RANGE_CH registers (address 0x03 to 0x06). Besides the already
supported ±10 V and ±5 V ranges, software mode can also accommodate the
±2.5 V range.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Co-developed-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
We need the staging fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On Spreadtrum platform, the headphone will read one ADC channel multiple
times to identify the headphone type, and the headphone identification is
sensitive of the ADC reading time. And we found it will take longer time
to reading ADC data by using interrupt mode comparing with the polling
mode, thus we should change to polling mode to improve the efficiency
of reading data, which can identify the headphone type successfully.
Signed-off-by: Freeman Liu <freeman.liu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use device-managed APIs to simplify the code.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 5.4 cycle
Note includes a merge from i3c tree to get support needed for stm_lsm6dsx driver
support for l3c devices. Done from immutable branch.
A counter subsystem patche in here as well.
Alongside the new device support (which is always good), Chuhong's work
on using devres managed APIs has cleaned up a number of drivers.
New device support
* adis16460
- New driver based on ADIS framework which needed addition of support
for cs_change_delay. Includes device tree binding.
* cros_ec
- Support fo the veyron-minnie which uses an older interface.
* lsm6dsx
- Support for LSM6DSTR-C gyro + magnetometer sensor (new IDs mainly)
- Support for ISM330DHCX acc + gyro sensor (extensive rework needed!)
* Maxim 5432
- New driver support MAX5432-MAX5435 family of potentiometers.
* noa1305
- New driver for this ON Semiconductor Ambient light sensor.
Features and cleanups
* tree wide
- Drop error prints after platform_get_irq as already prints errors
internally if any occur.
* docs
- Document mounting matrix.
- Fix a missing newline at end of file.
* ad2s1210
- Switch to device managed APIs for all of probe and drop explicit remove.
* ad7192
- Add of_device_id array to explicity handling DT bindings.
* ad7606
- Lots of rework leading to support for software configure modes in ad7616
parts.
- Debugfs register access support.
* am2315
- Switch to device managed APIs for all of probe and drop explicit remove.
* apds9960
- Typo in module description.
* cm36651
- Convert to i2c_new_dummy_device.
- Swithc to device managed APIs for all of probe adn drop explicit remove.
* cros_ec
- Calibscale support for accel, gyro and magnetometer.
- Tidy up some error codes to return the error from the stack rather than
-EIO.
- Determine protocol version.
- Add a sign vector to the core to fix sensor rotation if necessary.
Cannot just be done with mount matrix as already in use in many devices.
- Tidy up INFO_SCALE being in both the separate and shared lists.
- Drop a lot of dplicate code from the cros-ec-accel-legacy driver
and use the core provided code instead.
- Make frequency range available to userspace.
* counter / ftm-quaddec
- Switch to device managed APIs for all of probe adn drop explicit remove.
* hdc100x
- Switch to device managed APIs for all of probe and drop explicit remove.
* hi8435
- Use gpiod_set_value_cansleep as we don't care here and there is a
board out there where it needs to sleep.
- Switch to device managed APIs for all of probe and drop explict remove.
* hp03
- Convert to i2c_new_dummy_device.
* maxim thermocouple
- Switch to device managed APIs for all of probe and drop explicit remove.
* mmc35240
- Fix typo in constant naming.
* mpu6050
- Use devm_add_action_or_reset in place of explicit error handling.
- Make text in Kconfig more explicit about which parts are supported.
* mxc4005
- Switch to device managed APIs for all of probe and drop explicit remove.
* pms7003
- Convert device tree bindings to yaml.
- Add a MAINTAINERS entry
* sc27xx
- Introduce a local struct device *dev pointer to avoid lots of deref.
- Use devm_add_action_or_reset in place of explicit error handling.
* sca3000
- Typo fix in naming.
* si1145
- Switch to device managed APIs for all of probe and drop explicit remove.
* st_sensors
- Lots of rework to enable switch to regmap.
- Regmap conversion at the end.
- Tidy up some inconsistencies in buffer setup ops.
- Tidy up an oddity by dropping get_irq_data_ready function in favour
of direct access.
- Stop allocating buffer in buffer enable in favour of just embedding
a large enough constant size buffer in the iio_priv accessed structure.
* st_lsm6dsx
- l3c device support (LSM6DSO and LSM6DSR)
- tidy up irq return logic which was strangely written.
- fix up an ABI quirk where this driver used separate scale
attributes, even though they were always shared by type.
* stk33xx
- Device tree bindings include manufacturer ID.
* stm32-adc
- Add control for supply to analog switches including DT bindings.
* stm32 timer
- Drop the quadrature mode support. Believed there were no users so
take this opportunity to drop this unwanted ABI.
* tsl2772
- Switch to device mangage APIs for all of probe and drop explicit remove.
- Use regulator_bulk_* APIs to reduce repitition.
* veml6070
- Convert to i2c_new_dummy_device.
* tag 'iio-for-5.4a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (84 commits)
iio: hi8435: Drop hi8435_remove() by using devres for remaining elements
iio: hi8435: Use gpiod_set_value_cansleep()
iio:st_sensors: remove buffer allocation at each buffer enable
iio: imu: inv_mpu6050: be more explicit on supported chips
iio: light: noa1305: Add support for NOA1305
dt-bindings: Add binding document for NOA1305
iio: remove get_irq_data_ready() function pointer and use IRQ number directly
iio: imu: st_lsm6dsx: make IIO_CHAN_INFO_SCALE shared by type
iio: tsl2772: Use regulator_bulk_() APIs
iio: tsl2772: Use devm_iio_device_register
iio: tsl2772: Use devm_add_action_or_reset for tsl2772_chip_off
iio: tsl2772: Use devm_add_action_or_reset
iio: Remove dev_err() usage after platform_get_irq()
iio: light: si1145: Use device-managed APIs
iio:pressure: preenable/postenable/predisable fixup for ST press buffer
iio:magn: preenable/postenable/predisable fixup for ST magn buffer
iio:gyro: preenable/postenable/predisable fixup for ST gyro buffer
iio:accel: preenable/postenable/predisable fixup for ST accel buffer
dt-bindings: iio: imu: st_lsm6dsx: add ism330dhcx device bindings
iio: imu: st_lsm6dsx: add support to ISM330DHCX
...
|
|
Convert the remainder of hi8435_probe() to use devres and get rid of
hi8435_remove().
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-iio@vger.kernel.org
Cc: Chris Healy <cphealy@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use gpiod_set_value_cansleep() instead of gpiod_set_value() to support
the case when reset pin is connected to a GPIO expander. See ZII VF610
SCU4 AIB for one such example.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-iio@vger.kernel.org
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The max9611 driver reads the die temperature at probe time to validate
the communication channel. Use the actual read value to perform the test
instead of the read function return value, which was mistakenly used so
far.
The temperature reading test was only successful because the 0 return
value is in the range of supported temperatures.
Fixes: 69780a3bbc0b ("iio: adc: Add Maxim max9611 ADC driver")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: linux-iio@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Support for register access was added for devices which have software
mode.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Support for ad7616 running in software was added. In order
to activate the software mode, HW_RNGSEL pins must be pulled low.
Oversampling and input ranges are now configured in corresponding
registers. Ad7616 has multiple scale options when it is configured
in software mode.
Also, in order to support multiple devices in software mode, the spi
calculation of registers address must be generic. Because
the length of address and bit which specifies the read/write operation is
different for every device, calculation of address was made generic.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
According to datasheet, ad7616 require at least 15ms after a restart
to fully reconfigure and being able to receive new commands via spi.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Because software mode and register access are only available in spi, they
were moved in spi file and are accessbile via bops structure.
The write_os/scale will be overwritten by sw_mode_config function.
This patch was made in order to support devices in software mode without
making the driver dependent to spi and increase the abstraction of the
core.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The common channel definition which are going to be used by both core
file but also spi file, were moved in header file. Some devices have
different channel definitions when are used in software mode, feature
available only with spi, and those definitions will be added in spi file.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
gcc-9 complains about a blatant uninitialized variable use that
all earlier compiler versions missed:
drivers/iio/adc/rcar-gyroadc.c:510:5: warning: 'ret' may be used uninitialized in this function [-Wmaybe-uninitialized]
Return -EINVAL instead here and a few lines above it where
we accidentally return 0 on failure.
Cc: stable@vger.kernel.org
Fixes: 059c53b32329 ("iio: adc: Add Renesas GyroADC driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
On stm32h7 and stm32mp1, the ADC inputs are multiplexed with analog
switches which have reduced performances when their supply is below 2.7V
(vdda by default):
- 3.3V embedded booster can be used, to get full ADC performances
(increases power consumption).
- vdd supply can be selected if above 2.7V by setting ANASWVDD syscfg bit,
on STM32MP1 only.
Make this optional, since this is a trade-off between analog performance
and power consumption.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
devm_add_action_or_reset()
devm_add_action_or_reset() is introduced as a helper function which
internally calls devm_add_action(). If devm_add_action() fails
then it will execute the action mentioned and return the error code.
This reduce source code size (avoid writing the action twice)
and reduce the likelyhood of bugs.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Introduce local variable 'struct device *dev' and use it instead of
dereferencing it repeatly.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The SADC component can run at up to 8 MHz on JZ4725B, but is fed
a 12 MHz input clock (EXT). Divide it by two to get 6 MHz, then
set up another divider to match, to produce a 10us clock.
If the clock dividers are left on their power-on defaults (a divider
of 1), the SADC mostly works, but will occasionally produce erroneous
readings. This led to button presses being detected out of nowhere on
the RS90 every few minutes. With this change, no ghost button presses
were logged in almost a day worth of testing.
The ADCLK register for configuring clock dividers doesn't exist on
JZ4740, so avoid writing it there.
A function has been introduced rather than a flag because there is a lot
of variation between the ADCLK registers on JZ47xx SoCs, both in
the internal layout of the register and in the frequency range
supported by the SADC. So this solution should make it easier
to add support for other JZ47xx SoCs later.
Fixes: 1a78daea107d ("iio: adc: probe should set clock divider")
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Arguments are supposed to be ordered high then low.
Signed-off-by: Joe Perches <joe@perches.com>
Fixes: 69780a3bbc0b ("iio: adc: Add Maxim max9611 ADC driver")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO device support, features, cleanups and minor fixes for 5.3.
A few bits for the counters subsystem mixed in here as well.
There are some late breaking fixes as well, which aren't so urgent
they can't wait for the merge window.
New Device Support
* adf4371
- New driver + bindings.
- Support the adf4372 PLL. Mostly ID and bindings.
* ad8366 (note includes rework of driver needed to allow support for these).
- Support the ADL5240 variable gain amplifier (VGA).
- Support the ADA4961 digital gain amplifier (DGA).
* dps310
- New driver, in several parts from different authors for this temp
and pressure sensor.
- Includes errata workaround for a temperature reading issue.
* stk3310
- Support the stk3335, mostly ID.
Features and cleanups
* core
- drop error handling on debugfs registration.
- harden by making sure we don't overrun iio_chan_info_postfix.
* docs
- convert remaining docs to rst. At somepoint we'll fit these few
into the main IIO docs.
- improve sampling_frequency_available docs but explaining the
range form.
* ad_sigma_delta
- Drop a pointless goto.
* ad2s1210
- Drop pointless platform data null check seeing as we don't actually
use platform data anymore.
* ad7124
- Relax limitation on channel numbers to allow pseudo different channels.
- Support control of whether the input is buffered via DT.
- Use dynamic allocation for channel configuration to make it easier
to support new devices.
- YAML binding conversion.
* ad7150
- Comment tidy up.
- Consistent and simple if (ret) handling of i2c errors.
- FIELD_GET and GENMASK.
- Ternary rather than !!(condition) for readability.
- Use macros to avoid repetition of channel definitions.
* ad7606
- Add software channel config (rather that pin controlled)
- Refactor to simplify addition of new part in future.
* ad7746
- of_deivce_id table.
* ad7780
- MAINTAINERS entry
- YAML DT bindings.
* ad8366
- Stop using core mlock in favour of well scoped local lock.
- SPDX + copyright date update.
* ad9834
- of_device_id table
* adf4371
- Add support for output stage muting before lock on has occured.
* adis library
- MAINTAINERS entry to reflect that this now Alexandru's problem ;)
* adis162xx:
- Fix a slightly incorrect set of comments and print statements on
minimum supported voltage.
* adis16203
- of_device_id table.
* adis16240
- Add of_device_id table (in two parts as first patch only used it for
MODULE_DEVICE_TABLE.)
* adt7316-spi
- of_device_id table
* adxl372
- YAML DT binding conversion.
- Cleanup use of buffer callback functions (precursor to core rework).
* bh1710
- Simplify getting the i2c adapter from the client.
* dht11
- Mote to newer GPIO consumer interface.
* kxcjk-1013.c
- Add binding for sensor in display of some ultrabooks after userspace
tools updated for it not be a problem to report two similar sensors.
* imx7d
- drop unused variables.
- white space
- define instead of variable for clock frequency that is fixed.
- drop pointless error message.
* messon_saradc
- SPDX
* sps30
- MAINTAINERS entry
- YAML binding conversion.
* st_accel
- Tidy up ordering in various buffer related callbacks. This is
part of a long running effort to simplify the core code.
* stm32-dfsdm:
- Manage the resolution cleanly in triggerd modes.
- Add fast mode support which allows more flexible filter choices.
- Add a comment on the reason for a 16 bit record when technically
not 'required'.
* st_lsm6dsx
- Embed device name in the sensor_settings struct as i3c doesn't
have a convenient name field to use for this.
* xilinx-adc
- Relax constraints on supported platforms to reflect that this
can used with FPGAs on PCIe cards and hence many architectures.
* counters/ftm-quaddec
- Fix some formatting io MODULE_AUTHOR
- MAINTAINERS entry
Fixes
* tools
- fix incorrect handling of 32 bit channels.
* sca3000
- Potential endian bug that is unlikely to bite anyone (be64 host
seems unlikely for this old part).
* stm32-adc
- Add vdda-supply. On some boards it needs to be turned on to supply
the ADC. DT bindings included.
* stm32-dfsdm
- Fix output resolution to work with filter orders other than 3.
- Fix output datatype as it's signed and previously claimed not to be.
* tag 'iio-for-5.3b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (68 commits)
iio: iio-utils: Fix possible incorrect mask calculation
iio: frequency: adf4371: Add support for output stage mute
dt-bindings: iio: frequency: Add ADF4372 PLL documentation
iio: frequency: adf4371: Add support for ADF4372 PLL
dt-bindings: iio: adc: Add buffered input property
Convert AD7124 bindings documentation to YAML format.
iio: adc: ad7124: Shift to dynamic allocation for channel configuration
iio: adc: ad7124: Add buffered input support
iio: adc: ad7124: Remove input number limitation
MAINTAINERS: add ADIS IMU driver library entry
iio: adis162xx: fix low-power docs & reports
counter/ftm-quaddec: Add missing '>' in MODULE_AUTHOR
iio: core: no need to check return value of debugfs_create functions
docs: iio: convert to ReST
iio: adc: stm32-adc: add missing vdda-supply
dt-bindings: iio: adc: stm32: add missing vdda supply
iio: adc: stm32-dfsdm: add comment for 16 bits record
iio: adc: stm32-dfsdm: add fast mode support
iio: adc: stm32-dfsdm: manage data resolution in trigger mode
iio: adc: stm32-dfsdm: fix data type
...
|
|
This patch changes the channel configuration member of the device
structure from a fixed size array to a dynamic allocated one with a size
equal to the number of channels specified in the device tree. This will
ensure a more flexibility for compatible devices.
Ex. ad7124-4 - can have 4 differential or 8 pseudo-differential channels
ad7124-8 - can have 8 differential or 16 pseudo-differential channels
Also the device can suspport any other combination of differential and
pseudo-differential channels base on the physical number of inputs
available.
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This patch adds the option to enable the buffered mode for positive and
negative inputs. Each option can be enabled independently.
In buffered mode, the input channel feeds into a high impedance input stage
of the buffer amplifier. Therefore, the input can tolerate significant
source impedances and is tailored for direct connection to external
resistive type sensors such as strain gages or RTDs.
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The driver limits the user to use only 4/8 differential inputs, but this
device has the option to use pseudo-differential channels. This will
increase the number of channels to be equal with the number of inputs so 8
channels for ad7124-4 and 16 for ad7124-8.
This patch removes the check between channel nodes and num_inputs value.
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
We want the fixes and this resolves a merge issue as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add missing vdda-supply, analog power supply, to STM32 ADC. When vdda is
an independent supply, it needs to be properly turned on or off to supply
the ADC.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Fixes: 1add69880240 ("iio: adc: Add support for STM32 ADC core").
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add a comment on DMA configuration for 16 bits record.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The use of fast mode allows to get a larger set of solution
for filter parameters. This can be useful to reach a better
output sample resolution, when fast mode can be used.
Fast mode is selected at startup if it is relevant.
The startup is performed in postenable callback context,
where there are too tight time constraints for filter parameters
computation. For this reason both fast and non fast filter parameters
are pre-computed previously.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add output sample resolution management in scan mode.
Add stm32_dfsdm_process_data() function to share sample
processing between continuous and trigger modes.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Fix the data type as DFSDM raw output is complements 2,
24bits left aligned in a 32-bit register.
This change does not affect AUDIO path
- Set data as signed for IIO (as for AUDIO)
- Set 8 bit right shift for IIO.
The 8 LSBs bits of data contains channel info and are masked.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Fixes: e2e6771c6462 ("IIO: ADC: add STM32 DFSDM sigma delta ADC support")
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
In buffered mode, output samples are shifted left
unconditionally. This works for filter order 3,
but this shift is not adapted for other filter orders.
Compute required shift, left or right, and shift
output data accordingly.
Add also saturation management to avoid wrap-around
when maximum positive sample is reached.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Fixes: eca949800d2d ("IIO: ADC: add stm32 DFSDM support for PDM microphone")
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation the gpl this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
version 2 gplv2 for more details you should have received a copy of
the gnu general public license version 2 gplv2 along with this
source code
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 16 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081201.771169395@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since the XADC logic can be used with standalone Xilinx FPGAs, this
driver can potentially be used with many different platforms, not just
the Zynq and MicroBlaze platforms this driver was allowed to be built
for. There should be no platform-specific code in this driver, so just
delete the platform dependency.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
There is nothing being done after the `err_predisable` label, so just
remove it.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
average_en is always true, so there is not really need for
this structure member.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
All the parameters of devm_request_irq() can fit into a
single line, so place them all in a single line
for better readability.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Since the input clock is always 24MHz, there is no need for storing
this value into a variable.
Use a definition instead, which is more appropriate in this case.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
In case of ioremap failure, the core code will take care of printing
the error message, so there is no need for having a local error
message in the driver.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
