| Age | Commit message (Collapse) | Author |
|---|
|
You can't pass uninitialized "ret" variables to cci_write(). It has to
start as zero.
Fixes: 4f0aeba4f155 ("media: i2c: imx214: Convert to CCI register access helpers")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Add the capability of retrieving the min and max values of a
compound control.
[Ricardo: Added static to v4l2_ctrl_type_op_(maximum|minimum) proto]
[Ricardo: Fix documentation]
Signed-off-by: Yunke Cao <yunkec@google.com>
Tested-by: Yunke Cao <yunkec@google.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://lore.kernel.org/r/20250203-uvc-roi-v17-2-5900a9fed613@chromium.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
[hverkuil: fix small alignment checkpatch warning]
|
|
The driver defines IMX214_DEFAULT_LINK_FREQ 480000000, and then
IMX214_DEFAULT_PIXEL_RATE ((IMX214_DEFAULT_LINK_FREQ * 8LL) / 10),
which works out as 384MPix/s. (The 8 is 4 lanes and DDR.)
Parsing the PLL registers with the defined 24MHz input. We're in single
PLL mode, so MIPI frequency is directly linked to pixel rate. VTCK ends
up being 1200MHz, and VTPXCK and OPPXCK both are 120MHz. Section 5.3
"Frame rate calculation formula" says "Pixel rate
[pixels/s] = VTPXCK [MHz] * 4", so 120 * 4 = 480MPix/s, which basically
agrees with my number above.
3.1.4. MIPI global timing setting says "Output bitrate = OPPXCK * reg
0x113[7:0]", so 120MHz * 10, or 1200Mbit/s. That would be a link
frequency of 600MHz due to DDR.
That also matches to 480MPix/s * 10bpp / 4 lanes / 2 for DDR.
Keep the previous link frequency for backward compatibility.
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Fixes: 436190596241 ("media: imx214: Add imx214 camera sensor driver")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
This adds V4L2_CID_TEST_PATTERN control support.
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Check the chip ID and stop probing if it is no imx214 sensor.
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
The imx214 sensor supports analogue gain up to 8x and digital gain up to
16x. Implement the corresponding controls in the driver. Default gain
values are not modified by this patch.
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
The imx214 sensor supports horizontal and vertical flipping. Add
appropriate controls to the driver.
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Add vblank control to allow changing the framerate /
higher exposure values.
The vblank and hblank controls are needed for libcamera support.
While at it, fix the minimal exposure time according to the datasheet.
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
The imx214 camera is capable of either two-lane or four-lane operation.
Currently only the four-lane mode is supported, as proper pixel rates
and link frequences for the two-lane mode are unknown.
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
The IMX214_REG_EXPOSURE is configured twice, once with a hardcoded value
in the mode_<res> registers arrays, and once via v4l2_ctrl_ops. The
latter is enough, drop the former.
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Define macros for all the known registers used in the register arrays,
and use them to replace the numerical addresses. This improves
readability.
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Use the new common CCI register access helpers to replace the private
register access helpers in the imx214 driver. This simplifies the driver
by reducing the amount of code.
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Error handling in probe() can be a bit simpler with dev_err_probe().
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Port the imx214 sensor driver to use the subdev active state.
Move all the format configuration to the subdevice state and simplify
the format handling, locking and initialization.
While at it, simplify imx214_start_streaming() by removing unneeded goto
statements and the corresponding error label.
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
There were multiple issues in the driver's probe function related to
error handling:
- Device's PM runtime status wasn't reverted to suspended on some errors
in probe.
- Runtime PM was left enabled for the device on some probe errors.
- Device was left powered on if a probe failure happened or when it
was removed when it was powered on.
- An extra pm_runtime_set_suspended() was issued in driver's remove
function when the device was suspended.
Fix these bugs.
Fixes: 436190596241 ("media: imx214: Add imx214 camera sensor driver")
Cc: stable@vger.kernel.org # for >= v6.12
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
This reverts commit 9bc92332cc3f06fda3c6e2423995ca2da0a7ec9a.
Revert this "fix" as it's not really helpful but makes backporting a
proper fix harder.
Fixes: 9bc92332cc3f ("media: imx214: Fix the error handling in imx214_probe()")
Cc: stable@vger.kernel.org # for >= v6.12
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
The driver should disable regulators when fails to probe.
Link: https://lore.kernel.org/linux-media/20220510114852.1719018-1-zheyuma97@gmail.com
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Bo Liu <liubo03@inspur.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Due to a historical mishap, the v4l2_subdev_frame_interval structure
is the only part of the V4L2 subdev userspace API that doesn't contain a
'which' field. This prevents trying frame intervals using the subdev
'TRY' state mechanism.
Adding a 'which' field is simple as the structure has 8 reserved fields.
This would however break userspace as the field is currently set to 0,
corresponding to V4L2_SUBDEV_FORMAT_TRY, while the corresponding ioctls
currently operate on the 'ACTIVE' state. We thus need to add a new
subdev client cap, V4L2_SUBDEV_CLIENT_CAP_INTERVAL_USES_WHICH, to
indicate that userspace is aware of this new field.
All drivers that implement the subdev .get_frame_interval() and
.set_frame_interval() operations are updated to return -EINVAL when
operating on the TRY state, preserving the current behaviour.
While at it, fix a bad copy&paste in the documentation of the struct
v4l2_subdev_frame_interval_enum 'which' field.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> # for imx-media
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for tegra-video
Reviewed-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The subdev .[gs]_frame_interval are video operations, but they operate
on pads (and even on streams). Not only is this confusing, it causes
practical issues for drivers as the operations don't receive a subdev
state pointer, requiring manual state handling.
To improve the situation, turn the operations into pad operations, and
extend them to receive a state pointer like other pad operations.
While at it, rename the operations to .[gs]et_frame_interval at the same
time to match the naming scheme of other pad operations. This isn't
strictly necessary, but given that all drivers using those operations
need to be modified, handling the rename separately would generate more
churn for very little gain (if at all).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> # for imx-media
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for tegra-video
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Set effective and active sensor pixel sizes as shown in product
brief[1].
[1]: https://www.mouser.com/datasheet/2/897/ProductBrief_IMX214_20150428-1289331.pdf
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Obtain rotation and orientation information from system firmware and
register the appropriate controls. While at it, update number of
pre-allocated control slots.
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Code refinement.
While at it, don't destroy the mutex not initialized yet if the controls
are initialized incorrectly.
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Code refinement, no functional changes.
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
[Sakari Ailus: The control handler remains in the context struct still.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The subdev .init_cfg() operation is affected by two issues:
- It has long been extended to initialize a whole v4l2_subdev_state
instead of just a v4l2_subdev_pad_config, but its name has stuck
around.
- Despite operating on a whole subdev state and not being directly
exposed to the subdev users (either in-kernel or through the userspace
API), .init_cfg() is categorized as a subdev pad operation.
This participates in making the subdev API confusing for new developers.
Fix it by renaming the operation to .init_state(), and make it a subdev
internal operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Michael Riesch <michael.riesch@wolfvision.net> # for imx415
Acked-by: Shuah Khan <skhan@linuxfoundation.org> # for vimc
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
[Sakari Ailus: Resolved a conflict in Renesas vsp1 driver.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Switch all drivers accessing sub-device state to use the stream-aware
functions. We will soon remove the old ones.
This patch has been generated using the following Coccinelle script:
---------8<------------
@@
expression E1, E2, E3;
@@
- v4l2_subdev_get_pad_format(E1, E2, E3)
+ v4l2_subdev_state_get_format(E2, E3)
@@
expression E1, E2, E3;
@@
- v4l2_subdev_get_pad_crop(E1, E2, E3)
+ v4l2_subdev_state_get_crop(E2, E3)
@@
expression E1, E2, E3;
@@
- v4l2_subdev_get_pad_compose(E1, E2, E3)
+ v4l2_subdev_state_get_compose(E2, E3)
@@
expression E1, E2, E3;
@@
- v4l2_subdev_get_try_format(E1, E2, E3)
+ v4l2_subdev_state_get_format(E2, E3)
@@
expression E1, E2, E3;
@@
- v4l2_subdev_get_try_crop(E1, E2, E3)
+ v4l2_subdev_state_get_crop(E2, E3)
@@
expression E1, E2, E3;
@@
- v4l2_subdev_get_try_compose(E1, E2, E3)
+ v4l2_subdev_state_get_compose(E2, E3)
---------8<------------
Additionally drivers/media/i2c/s5k5baf.c and
drivers/media/platform/samsung/s3c-camif/camif-capture.c have been
manually changed as Coccinelle didn't. Further local variables have been
removed as they became unused as a result of the other changes.
Also Coccinelle introduced indentation by space in files
drivers/media/i2c/st-mipid02.c and
drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c. This has been also
corrected.
The diff from Coccinelle-generated changes are:
> diff --git b/drivers/media/i2c/imx319.c a/drivers/media/i2c/imx319.c
> index e549692ff478..420984382173 100644
> --- b/drivers/media/i2c/imx319.c
> +++ a/drivers/media/i2c/imx319.c
> @@ -2001,7 +2001,6 @@ static int imx319_do_get_pad_format(struct imx319 *imx319,
> struct v4l2_subdev_format *fmt)
> {
> struct v4l2_mbus_framefmt *framefmt;
> - struct v4l2_subdev *sd = &imx319->sd;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> diff --git b/drivers/media/i2c/imx355.c a/drivers/media/i2c/imx355.c
> index 96bdde685d65..e1b1d2fc79dd 100644
> --- b/drivers/media/i2c/imx355.c
> +++ a/drivers/media/i2c/imx355.c
> @@ -1299,7 +1299,6 @@ static int imx355_do_get_pad_format(struct imx355 *imx355,
> struct v4l2_subdev_format *fmt)
> {
> struct v4l2_mbus_framefmt *framefmt;
> - struct v4l2_subdev *sd = &imx355->sd;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> diff --git b/drivers/media/i2c/ov08x40.c a/drivers/media/i2c/ov08x40.c
> index ca799bbcfdb7..abbb0b774d43 100644
> --- b/drivers/media/i2c/ov08x40.c
> +++ a/drivers/media/i2c/ov08x40.c
> @@ -2774,7 +2774,6 @@ static int ov08x40_do_get_pad_format(struct ov08x40 *ov08x,
> struct v4l2_subdev_format *fmt)
> {
> struct v4l2_mbus_framefmt *framefmt;
> - struct v4l2_subdev *sd = &ov08x->sd;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> diff --git b/drivers/media/i2c/ov13858.c a/drivers/media/i2c/ov13858.c
> index 7816d9787c61..09387e335d80 100644
> --- b/drivers/media/i2c/ov13858.c
> +++ a/drivers/media/i2c/ov13858.c
> @@ -1316,7 +1316,6 @@ static int ov13858_do_get_pad_format(struct ov13858 *ov13858,
> struct v4l2_subdev_format *fmt)
> {
> struct v4l2_mbus_framefmt *framefmt;
> - struct v4l2_subdev *sd = &ov13858->sd;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> diff --git b/drivers/media/i2c/ov13b10.c a/drivers/media/i2c/ov13b10.c
> index 268cd4b03f9c..c06411d5ee2b 100644
> --- b/drivers/media/i2c/ov13b10.c
> +++ a/drivers/media/i2c/ov13b10.c
> @@ -1001,7 +1001,6 @@ static int ov13b10_do_get_pad_format(struct ov13b10 *ov13b,
> struct v4l2_subdev_format *fmt)
> {
> struct v4l2_mbus_framefmt *framefmt;
> - struct v4l2_subdev *sd = &ov13b->sd;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> diff --git b/drivers/media/i2c/s5c73m3/s5c73m3-core.c a/drivers/media/i2c/s5c73m3/s5c73m3-core.c
> index 47605e36bc60..8f9b5713daf7 100644
> --- b/drivers/media/i2c/s5c73m3/s5c73m3-core.c
> +++ a/drivers/media/i2c/s5c73m3/s5c73m3-core.c
> @@ -819,7 +819,6 @@ static void s5c73m3_oif_try_format(struct s5c73m3 *state,
> struct v4l2_subdev_format *fmt,
> const struct s5c73m3_frame_size **fs)
> {
> - struct v4l2_subdev *sd = &state->sensor_sd;
> u32 code;
>
> switch (fmt->pad) {
> diff --git a/drivers/media/i2c/s5k5baf.c b/drivers/media/i2c/s5k5baf.c
> index 67da2045f543..03ccfb0e1e11 100644
> --- a/drivers/media/i2c/s5k5baf.c
> +++ b/drivers/media/i2c/s5k5baf.c
> @@ -1472,14 +1472,11 @@ static int s5k5baf_set_selection(struct v4l2_subdev *sd,
>
> if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
> rects = (struct v4l2_rect * []) {
> - &s5k5baf_cis_rect,
> - v4l2_subdev_get_try_crop(sd, sd_state,
> - PAD_CIS),
> - v4l2_subdev_get_try_compose(sd, sd_state,
> - PAD_CIS),
> - v4l2_subdev_get_try_crop(sd, sd_state,
> - PAD_OUT)
> - };
> + &s5k5baf_cis_rect,
> + v4l2_subdev_state_get_crop(sd_state, PAD_CIS),
> + v4l2_subdev_state_get_compose(sd_state, PAD_CIS),
> + v4l2_subdev_state_get_crop(sd_state, PAD_OUT)
> + };
> s5k5baf_set_rect_and_adjust(rects, rtype, &sel->r);
> return 0;
> }
> diff --git b/drivers/media/platform/samsung/s3c-camif/camif-capture.c a/drivers/media/platform/samsung/s3c-camif/camif-capture.c
> index 295e083f38e8..be58260ea67e 100644
> --- b/drivers/media/platform/samsung/s3c-camif/camif-capture.c
> +++ a/drivers/media/platform/samsung/s3c-camif/camif-capture.c
> @@ -1216,7 +1216,7 @@ static int s3c_camif_subdev_get_fmt(struct v4l2_subdev *sd,
> struct v4l2_mbus_framefmt *mf = &fmt->format;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> - mf = v4l2_subdev_get_try_format(sd, sd_state, fmt->pad);
> + mf = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> fmt->format = *mf;
> return 0;
> }
> @@ -1305,7 +1305,7 @@ static int s3c_camif_subdev_set_fmt(struct v4l2_subdev *sd,
> __camif_subdev_try_format(camif, mf, fmt->pad);
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> - mf = v4l2_subdev_get_try_format(sd, sd_state, fmt->pad);
> + mf = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> *mf = fmt->format;
> mutex_unlock(&camif->lock);
> return 0;
> diff --git b/drivers/media/platform/ti/cal/cal-camerarx.c a/drivers/media/platform/ti/cal/cal-camerarx.c
> index cea454ed9c20..61433744c6c4 100644
> --- b/drivers/media/platform/ti/cal/cal-camerarx.c
> +++ a/drivers/media/platform/ti/cal/cal-camerarx.c
> @@ -621,8 +621,6 @@ static int cal_camerarx_sd_enum_mbus_code(struct v4l2_subdev *sd,
> struct v4l2_subdev_state *state,
> struct v4l2_subdev_mbus_code_enum *code)
> {
> - struct cal_camerarx *phy = to_cal_camerarx(sd);
> -
> /* No transcoding, source and sink codes must match. */
> if (cal_rx_pad_is_source(code->pad)) {
> struct v4l2_mbus_framefmt *fmt;
> diff --git b/drivers/staging/media/imx/imx-ic-prp.c a/drivers/staging/media/imx/imx-ic-prp.c
> index dd558fac6477..61d69f19657e 100644
> --- b/drivers/staging/media/imx/imx-ic-prp.c
> +++ a/drivers/staging/media/imx/imx-ic-prp.c
> @@ -82,8 +82,6 @@ static struct v4l2_mbus_framefmt *
> __prp_get_fmt(struct prp_priv *priv, struct v4l2_subdev_state *sd_state,
> unsigned int pad, enum v4l2_subdev_format_whence which)
> {
> - struct imx_ic_priv *ic_priv = priv->ic_priv;
> -
> if (which == V4L2_SUBDEV_FORMAT_TRY)
> return v4l2_subdev_state_get_format(sd_state, pad);
> else
> diff --git b/drivers/staging/media/imx/imx-ic-prpencvf.c a/drivers/staging/media/imx/imx-ic-prpencvf.c
> index 02db7dbb884b..ec73c901079e 100644
> --- b/drivers/staging/media/imx/imx-ic-prpencvf.c
> +++ a/drivers/staging/media/imx/imx-ic-prpencvf.c
> @@ -790,8 +790,6 @@ static struct v4l2_mbus_framefmt *
> __prp_get_fmt(struct prp_priv *priv, struct v4l2_subdev_state *sd_state,
> unsigned int pad, enum v4l2_subdev_format_whence which)
> {
> - struct imx_ic_priv *ic_priv = priv->ic_priv;
> -
> if (which == V4L2_SUBDEV_FORMAT_TRY)
> return v4l2_subdev_state_get_format(sd_state, pad);
> else
> diff --git a/drivers/media/i2c/st-mipid02.c b/drivers/media/i2c/st-mipid02.c
> index 9c9361354c00..b08a249b5fdd 100644
> --- a/drivers/media/i2c/st-mipid02.c
> +++ b/drivers/media/i2c/st-mipid02.c
> @@ -751,7 +751,7 @@ static void mipid02_set_fmt_source(struct v4l2_subdev *sd,
> format->format = bridge->fmt;
> else
> format->format = *v4l2_subdev_state_get_format(sd_state,
> - MIPID02_SINK_0);
> + MIPID02_SINK_0);
>
> /* but code may need to be converted */
> format->format.code = serial_to_parallel_code(format->format.code);
> diff --git a/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c b/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c
> index 117912d3bfbd..96353648c032 100644
> --- a/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c
> +++ b/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c
> @@ -319,7 +319,7 @@ static void rkisp1_isp_start(struct rkisp1_isp *isp,
> rkisp1_write(rkisp1, RKISP1_CIF_ISP_CTRL, val);
>
> src_fmt = v4l2_subdev_state_get_format(sd_state,
> - RKISP1_ISP_PAD_SOURCE_VIDEO);
> + RKISP1_ISP_PAD_SOURCE_VIDEO);
> src_info = rkisp1_mbus_info_get_by_code(src_fmt->code);
>
> if (src_info->pixel_enc != V4L2_PIXEL_ENC_BAYER)
> @@ -475,9 +475,9 @@ static void rkisp1_isp_set_src_fmt(struct rkisp1_isp *isp,
> sink_fmt = v4l2_subdev_state_get_format(sd_state,
> RKISP1_ISP_PAD_SINK_VIDEO);
> src_fmt = v4l2_subdev_state_get_format(sd_state,
> - RKISP1_ISP_PAD_SOURCE_VIDEO);
> + RKISP1_ISP_PAD_SOURCE_VIDEO);
> src_crop = v4l2_subdev_state_get_crop(sd_state,
> - RKISP1_ISP_PAD_SOURCE_VIDEO);
> + RKISP1_ISP_PAD_SOURCE_VIDEO);
>
> /*
> * Media bus code. The ISP can operate in pass-through mode (Bayer in,
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Stopping streaming on a camera pipeline at system suspend time, and
restarting it at system resume time, requires coordinated action between
the bridge driver and the camera sensor driver. This is handled by the
bridge driver calling the sensor's .s_stream() handler at system suspend
and resume time. There is thus no need for the sensor to independently
implement system sleep PM operations. Drop them.
The streaming field of the driver's private structure is now unused,
drop it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The subdev .s_stream() operation shall not be called to start streaming
on an already started subdev, or stop streaming on a stopped subdev.
Remove the check that guards against that condition.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
commit 03c835f498b5 ("i2c: Switch .probe() to not take an id parameter")
convert back to (the new) .probe() to be able to eventually drop
.probe_new() from struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
We have 'struct v4l2_subdev_pad_config' which contains configuration for
a single pad used for the TRY functionality, and an array of those
structs is passed to various v4l2_subdev_pad_ops.
I was working on subdev internal routing between pads, and realized that
there's no way to add TRY functionality for routes, which is not pad
specific configuration. Adding a separate struct for try-route config
wouldn't work either, as e.g. set-fmt needs to know the try-route
configuration to propagate the settings.
This patch adds a new struct, 'struct v4l2_subdev_state' (which at the
moment only contains the v4l2_subdev_pad_config array) and the new
struct is used in most of the places where v4l2_subdev_pad_config was
used. All v4l2_subdev_pad_ops functions taking v4l2_subdev_pad_config
are changed to instead take v4l2_subdev_state.
The changes to drivers/media/v4l2-core/v4l2-subdev.c and
include/media/v4l2-subdev.h were written by hand, and all the driver
changes were done with the semantic patch below. The spatch needs to be
applied to a select list of directories. I used the following shell
commands to apply the spatch:
dirs="drivers/media/i2c drivers/media/platform drivers/media/usb drivers/media/test-drivers/vimc drivers/media/pci drivers/staging/media"
for dir in $dirs; do spatch -j8 --dir --include-headers --no-show-diff --in-place --sp-file v4l2-subdev-state.cocci $dir; done
Note that Coccinelle chokes on a few drivers (gcc extensions?). With
minor changes we can make Coccinelle run fine, and these changes can be
reverted after spatch. The diff for these changes is:
For drivers/media/i2c/s5k5baf.c:
@@ -1481,7 +1481,7 @@ static int s5k5baf_set_selection(struct v4l2_subdev *sd,
&s5k5baf_cis_rect,
v4l2_subdev_get_try_crop(sd, cfg, PAD_CIS),
v4l2_subdev_get_try_compose(sd, cfg, PAD_CIS),
- v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT)
+ v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT),
};
s5k5baf_set_rect_and_adjust(rects, rtype, &sel->r);
return 0;
For drivers/media/platform/s3c-camif/camif-capture.c:
@@ -1230,7 +1230,7 @@ static int s3c_camif_subdev_get_fmt(struct v4l2_subdev *sd,
*mf = camif->mbus_fmt;
break;
- case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P:
+ case CAMIF_SD_PAD_SOURCE_C:
/* crop rectangle at camera interface input */
mf->width = camif->camif_crop.width;
mf->height = camif->camif_crop.height;
@@ -1332,7 +1332,7 @@ static int s3c_camif_subdev_set_fmt(struct v4l2_subdev *sd,
}
break;
- case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P:
+ case CAMIF_SD_PAD_SOURCE_C:
/* Pixel format can be only changed on the sink pad. */
mf->code = camif->mbus_fmt.code;
mf->width = crop->width;
The semantic patch is:
// <smpl>
// Change function parameter
@@
identifier func;
identifier cfg;
@@
func(...,
- struct v4l2_subdev_pad_config *cfg
+ struct v4l2_subdev_state *sd_state
, ...)
{
<...
- cfg
+ sd_state
...>
}
// Change function declaration parameter
@@
identifier func;
identifier cfg;
type T;
@@
T func(...,
- struct v4l2_subdev_pad_config *cfg
+ struct v4l2_subdev_state *sd_state
, ...);
// Change function return value
@@
identifier func;
@@
- struct v4l2_subdev_pad_config
+ struct v4l2_subdev_state
*func(...)
{
...
}
// Change function declaration return value
@@
identifier func;
@@
- struct v4l2_subdev_pad_config
+ struct v4l2_subdev_state
*func(...);
// Some drivers pass a local pad_cfg for a single pad to a called function. Wrap it
// inside a pad_state.
@@
identifier func;
identifier pad_cfg;
@@
func(...)
{
...
struct v4l2_subdev_pad_config pad_cfg;
+ struct v4l2_subdev_state pad_state = { .pads = &pad_cfg };
<+...
(
v4l2_subdev_call
|
sensor_call
|
isi_try_fse
|
isc_try_fse
|
saa_call_all
)
(...,
- &pad_cfg
+ &pad_state
,...)
...+>
}
// If the function uses fields from pad_config, access via state->pads
@@
identifier func;
identifier state;
@@
func(...,
struct v4l2_subdev_state *state
, ...)
{
<...
(
- state->try_fmt
+ state->pads->try_fmt
|
- state->try_crop
+ state->pads->try_crop
|
- state->try_compose
+ state->pads->try_compose
)
...>
}
// If the function accesses the filehandle, use fh->state instead
@@
struct v4l2_subdev_fh *fh;
@@
- fh->pad
+ fh->state
@@
struct v4l2_subdev_fh fh;
@@
- fh.pad
+ fh.state
// Start of vsp1 specific
@@
@@
struct vsp1_entity {
...
- struct v4l2_subdev_pad_config *config;
+ struct v4l2_subdev_state *config;
...
};
@@
symbol entity;
@@
vsp1_entity_init(...)
{
...
entity->config =
- v4l2_subdev_alloc_pad_config
+ v4l2_subdev_alloc_state
(&entity->subdev);
...
}
@@
symbol entity;
@@
vsp1_entity_destroy(...)
{
...
- v4l2_subdev_free_pad_config
+ v4l2_subdev_free_state
(entity->config);
...
}
@exists@
identifier func =~ "(^vsp1.*)|(hsit_set_format)|(sru_enum_frame_size)|(sru_set_format)|(uif_get_selection)|(uif_set_selection)|(uds_enum_frame_size)|(uds_set_format)|(brx_set_format)|(brx_get_selection)|(histo_get_selection)|(histo_set_selection)|(brx_set_selection)";
symbol config;
@@
func(...) {
...
- struct v4l2_subdev_pad_config *config;
+ struct v4l2_subdev_state *config;
...
}
// End of vsp1 specific
// Start of rcar specific
@@
identifier sd;
identifier pad_cfg;
@@
rvin_try_format(...)
{
...
- struct v4l2_subdev_pad_config *pad_cfg;
+ struct v4l2_subdev_state *sd_state;
...
- pad_cfg = v4l2_subdev_alloc_pad_config(sd);
+ sd_state = v4l2_subdev_alloc_state(sd);
<...
- pad_cfg
+ sd_state
...>
- v4l2_subdev_free_pad_config(pad_cfg);
+ v4l2_subdev_free_state(sd_state);
...
}
// End of rcar specific
// Start of rockchip specific
@@
identifier func =~ "(rkisp1_rsz_get_pad_fmt)|(rkisp1_rsz_get_pad_crop)|(rkisp1_rsz_register)";
symbol rsz;
symbol pad_cfg;
@@
func(...)
{
+ struct v4l2_subdev_state state = { .pads = rsz->pad_cfg };
...
- rsz->pad_cfg
+ &state
...
}
@@
identifier func =~ "(rkisp1_isp_get_pad_fmt)|(rkisp1_isp_get_pad_crop)";
symbol isp;
symbol pad_cfg;
@@
func(...)
{
+ struct v4l2_subdev_state state = { .pads = isp->pad_cfg };
...
- isp->pad_cfg
+ &state
...
}
@@
symbol rkisp1;
symbol isp;
symbol pad_cfg;
@@
rkisp1_isp_register(...)
{
+ struct v4l2_subdev_state state = { .pads = rkisp1->isp.pad_cfg };
...
- rkisp1->isp.pad_cfg
+ &state
...
}
// End of rockchip specific
// Start of tegra-video specific
@@
identifier sd;
identifier pad_cfg;
@@
__tegra_channel_try_format(...)
{
...
- struct v4l2_subdev_pad_config *pad_cfg;
+ struct v4l2_subdev_state *sd_state;
...
- pad_cfg = v4l2_subdev_alloc_pad_config(sd);
+ sd_state = v4l2_subdev_alloc_state(sd);
<...
- pad_cfg
+ sd_state
...>
- v4l2_subdev_free_pad_config(pad_cfg);
+ v4l2_subdev_free_state(sd_state);
...
}
@@
identifier sd_state;
@@
__tegra_channel_try_format(...)
{
...
struct v4l2_subdev_state *sd_state;
<...
- sd_state->try_crop
+ sd_state->pads->try_crop
...>
}
// End of tegra-video specific
// </smpl>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Commit dd8088d5a896 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors.
Use the new API, in order to cleanup the error check logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Rename v4l2_async_register_subdev_sensor_common as
v4l2_async_register_subdev_sensor. This is a part of the effort to make
the long names present in V4L2 fwnode and async frameworks shorter.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Stop video streaming when requested.
When s_stream is called to stop the video streaming, if/else condition calls
start_streaming function instead of the one for stopping it.
Fixes: 436190596241 ("media: imx214: Add imx214 camera sensor driver")
Signed-off-by: Daniel Gomez <daniel@qtec.com>
Signed-off-by: Ricardo Ribalda <ribalda@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Modify emails to ribalda@kernel.org and unify my surname in all the
files.
Signed-off-by: Ricardo Ribalda <ribalda@kernel.org>
Link: https://lore.kernel.org/r/20200430135224.362700-1-ricardo@ribalda.com
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
The pad is now checked by v4l2_subdev_call_wappers
call_g_frame_interval-> check_frame_interval-> check_pad
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
According to the product brief, the unit cell size is 1120 nanometers^2.
https://www.sony-semicon.co.jp/products_en/IS/sensor1/img/products/ProductBrief_IMX214_20150428.pdf
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
This patch fixes a spelling typo found in imx214.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
As warned by smatch:
drivers/media/i2c/imx214.c:591 imx214_set_format() warn: variable dereferenced before check 'format' (see line 589)
It turns that the code at imx214_set_format() has support for being
called with the format being NULL. I've no idea why, as it is only
called internally with the pointer set, and via subdev API (with
should also set it).
Also, the entire logic there depends on having format != NULL, so
just remove the bogus broken support for a null format.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Ricardo Ribalda Delgado <ricardo@ribalda.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Use codespell to fix lots of typos over frontends.
Manually verified to avoid false-positives.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Clang warns when a variable is assigned to itself:
drivers/media/i2c/imx214.c:695:13: error: explicitly assigning value of
variable of type 'const struct reg_8 *' to itself
[-Werror,-Wself-assign]
for (table = table; table->addr != IMX214_TABLE_END ; table++) {
~~~~~ ^ ~~~~~
1 error generated.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Add a V4L2 sub-device driver for the Sony IMX214 image sensor.
This is a camera sensor using the I2C bus for control and the
CSI-2 bus for data.
Tested on a DB820c alike board with Intrinsyc Open-Q 13MP camera.
[Sakari Ailus: squash exposure time max limit patch]
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
