| Age | Commit message (Collapse) | Author |
|---|
|
The original driver first unregisters then re-registers all multicast
addresses in the struct net_device_ops::ndo_set_rx_mode() callback.
As the networking stack calls ndo_set_rx_mode() if a single multicast
address change occurs, a significant amount of time may be used to first
unregister and then re-register unchanged multicast addresses. This
leads to performance issues when tracking large numbers of multicast
addresses.
Replace the unregister and register loop and the hand crafted
mc_addr_list list handling with __dev_mc_sync(), to only update entries
which have changed.
On profiling with an fsl_dpa NIC, this patch presented a speedup of
around 40 when successively setting up 2000 multicast groups using
setsockopt(), without drawbacks on smaller numbers of multicast groups.
Signed-off-by: Jonas Rebmann <jre@pengutronix.de>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Virtually all conventional network drivers are now converted to use
phylink_generic_validate() - only DSA drivers and fman_memac remain,
so lets remove the necessity for network drivers to explicitly set
this member, and default to phylink_generic_validate() when unset.
This is possible as .validate must currently be set.
Any remaining instances that have not been addressed by this patch can
be fixed up later.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/E1or0FZ-001tRa-DI@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This converts DPAA to phylink. All macs are converted. This should work
with no device tree modifications (including those made in this series),
except for QSGMII (as noted previously).
The mEMAC configuration is one of the tricker areas. I have tried to
capture all the restrictions across the various models. Most of the time,
we assume that if the serdes supports a mode or the phy-interface-mode
specifies it, then we support it. The only place we can't do this is
(RG)MII, since there's no serdes. In that case, we rely on a (new)
devicetree property. There are also several cases where half-duplex is
broken. Unfortunately, only a single compatible is used for the MAC, so we
have to use the board compatible instead.
The 10GEC conversion is very straightforward, since it only supports XAUI.
There is generally nothing to configure.
The dTSEC conversion is broadly similar to mEMAC, but is simpler because we
don't support configuring the SerDes (though this can be easily added) and
we don't have multiple PCSs. From what I can tell, there's nothing
different in the driver or documentation between SGMII and 1000BASE-X
except for the advertising. Similarly, I couldn't find anything about
2500BASE-X. In both cases, I treat them like SGMII. These modes aren't used
by any in-tree boards. Similarly, despite being mentioned in the driver, I
couldn't find any documented SoCs which supported QSGMII. I have left it
unimplemented for now.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of setting the queue depth once during probe, adjust it on the
fly whenever we configure the link. This is a bit unusal, since usually
the DPAA driver calls into the FMAN driver, but here we do the opposite.
We need to add a netdev to struct mac_device for this, but it will soon
live in the phylink config.
I haven't tested this extensively, but it doesn't seem to break
anything. We could possibly optimize this a bit by keeping track of the
last rate, but for now we just update every time. 10GEC probably doesn't
need to call into this at all, but I've added it for consistency.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When disabling, there is nothing we can do about errors. In fact, the
only error which can occur is misuse of the API. Just warn in the mac
driver instead.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of using a void pointer for mac_dev, specify its type
explicitly.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some params are already present in mac_dev. Use them directly instead of
passing them through params.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of having the mac init functions call back into the fman core to
get their params, just pass them directly to the init functions.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are several small functions which were only necessary because the
initialization functions didn't have access to the mac private data. Now
that they do, just do things directly.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These methods are no longer accessed outside of the driver file, so mark
them as static.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This moves mac-specific initialization to mac-specific files. This will
make it easier to work with individual macs. It will also make it easier
to refactor the initialization to simplify the control flow. No
functional change intended.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mac_priv_s->enable() and ->disable() are always called with
a comm_mode of COMM_MODE_RX_AND_TX. Remove this parameter, and refactor
the macs appropriately.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Tested-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This converts the license text of files in the fman directory to use
SPDX license identifiers instead.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Tested-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This big patch sprinkles const on local variables and
function arguments which may refer to netdev->dev_addr.
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Some of the changes here are not strictly required - const
is sometimes cast off but pointer is not used for writing.
It seems like it's still better to add the const in case
the code changes later or relevant -W flags get enabled
for the build.
No functional changes.
Link: https://lore.kernel.org/r/20211014142432.449314-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a safe check to avoid dereferencing null pointer
Fixes: 57ba4c9b56d8 ("fsl/fman: Add FMan MAC support")
Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow the initialization of the MAC to be performed even if the
device tree does not provide a valid MAC address. Later a random
MAC address should be assigned by the Ethernet driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These functions are called from atomic context:
[ 9.150239] BUG: sleeping function called from invalid context at /home/scott/git/linux/mm/slab.h:421
[ 9.158159] in_atomic(): 1, irqs_disabled(): 0, pid: 4432, name: ip
[ 9.163128] CPU: 8 PID: 4432 Comm: ip Not tainted 4.20.0-rc2-00169-g63d86876f324 #29
[ 9.163130] Call Trace:
[ 9.170701] [c0000002e899a980] [c0000000009c1068] .dump_stack+0xa8/0xec (unreliable)
[ 9.177140] [c0000002e899aa10] [c00000000007a7b4] .___might_sleep+0x138/0x164
[ 9.184440] [c0000002e899aa80] [c0000000001d5bac] .kmem_cache_alloc_trace+0x238/0x30c
[ 9.191216] [c0000002e899ab40] [c00000000065ea1c] .memac_add_hash_mac_address+0x104/0x198
[ 9.199464] [c0000002e899abd0] [c00000000065a788] .set_multi+0x1c8/0x218
[ 9.206242] [c0000002e899ac80] [c0000000006615ec] .dpaa_set_rx_mode+0xdc/0x17c
[ 9.213544] [c0000002e899ad00] [c00000000083d2b0] .__dev_set_rx_mode+0x80/0xd4
[ 9.219535] [c0000002e899ad90] [c00000000083d334] .dev_set_rx_mode+0x30/0x54
[ 9.225271] [c0000002e899ae10] [c00000000083d4a0] .__dev_open+0x148/0x1c8
[ 9.230751] [c0000002e899aeb0] [c00000000083d934] .__dev_change_flags+0x19c/0x1e0
[ 9.230755] [c0000002e899af60] [c00000000083d9a4] .dev_change_flags+0x2c/0x80
[ 9.242752] [c0000002e899aff0] [c0000000008554ec] .do_setlink+0x350/0xf08
[ 9.248228] [c0000002e899b170] [c000000000857ad0] .rtnl_newlink+0x588/0x7e0
[ 9.253965] [c0000002e899b740] [c000000000852424] .rtnetlink_rcv_msg+0x3e0/0x498
[ 9.261440] [c0000002e899b820] [c000000000884790] .netlink_rcv_skb+0x134/0x14c
[ 9.267607] [c0000002e899b8e0] [c000000000851840] .rtnetlink_rcv+0x18/0x2c
[ 9.274558] [c0000002e899b950] [c000000000883c8c] .netlink_unicast+0x214/0x318
[ 9.281163] [c0000002e899ba00] [c000000000884220] .netlink_sendmsg+0x348/0x444
[ 9.287076] [c0000002e899bae0] [c00000000080d13c] .sock_sendmsg+0x2c/0x54
[ 9.287080] [c0000002e899bb50] [c0000000008106c0] .___sys_sendmsg+0x2d0/0x2d8
[ 9.298375] [c0000002e899bd30] [c000000000811a80] .__sys_sendmsg+0x5c/0xb0
[ 9.303939] [c0000002e899be20] [c0000000000006b0] system_call+0x60/0x6c
Signed-off-by: Scott Wood <oss@buserror.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to add set_tstamp interface for memac,
dtsec, and 10GEC controllers to configure HW timestamping.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds allmulticast option for memac, dtsec
and 10GEC controllers.
Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We set "tgec->cfg" to NULL before passing it to kfree(). There is no
need to set it to NULL at all. Let's just delete it.
Fixes: 57ba4c9b56d8 ("fsl/fman: Add FMan MAC support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the Data Path Acceleration Architecture Frame Manger MAC support.
This patch adds The FMan MAC configuration, initialization and
runtime control routines.
This patch contains support for these types of MACs:
- dTSEC: Three speed Ethernet controller (10/100/1000 Mbps)
- tGEC: 10G Ethernet controller (10 Gbps)
- mEMAC: Multi-rate Ethernet MAC (10/100/1000/10000 Mbps)
Different FMan revisions have different type and number of MACs.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
