| Age | Commit message (Collapse) | Author |
|---|
|
During initialization, the AF driver resets all blocks. The RPM (MAC)
block and NIX block operate on a credit-based model. When the NIX block
resets during active traffic flow, it doesn't release credits to the RPM
block. This causes the RPM FIFO to overflow, leading to receive traffic
struck.
To address this issue, the patch introduces the following changes:
1. Stop receiving traffic at the MAC level during AF driver
initialization.
2. Perform an X2P reset (prevents RXFIFO of all LMACS from pushing data)
3. Reset the NIX block.
4. Clear the X2P reset and re-enable receiving traffic.
Fixes: 54d557815e15 ("octeontx2-af: Reset all RVU blocks")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Low network performance is observed even on RPMs with larger
FIFO lengths.
The cn10kb silicon has three RPM blocks with the following
FIFO sizes:
--------------------
| RPM0 | 256KB |
| RPM1 | 256KB |
| RPM2 | 128KB |
--------------------
The current design stores the FIFO length in a common structure for all
RPMs (mac_ops). As a result, the FIFO length of the last RPM is applied
to all RPMs, leading to reduced network performance.
This patch resolved the problem by storing the fifo length in per MAC
structure (cgx).
Fixes: b9d0fedc6234 ("octeontx2-af: cn10kb: Add RPM_USX MAC support")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Reset CGX/RPM MAC HW statistics at the time of driver probe()
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Upon physical link change, firmware reports to the kernel about the
change along with the details like speed, lmac_type_id, etc.
Kernel derives lmac_type based on lmac_type_id received from firmware.
This patch extends current lmac list with new USGMII mode supported
by CN10KB RPM block.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
AF driver configures MAC features like internal loopback and PFC upon
receiving the request from PF and its VF netdev. But these
features are not getting reset in FLR. This patch fixes the issue by
resetting the same.
Fixes: 23999b30ae67 ("octeontx2-af: Enable or disable CGX internal loopback")
Fixes: 1121f6b02e7a ("octeontx2-af: Priority flow control configuration support")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PF netdev can request AF to enable or disable reception and transmission
on assigned CGX::LMAC. The current code instead of disabling or enabling
'reception and transmission' also disables/enable the LMAC. This patch
fixes this issue.
Fixes: 1435f66a28b4 ("octeontx2-af: CGX Rx/Tx enable/disable mbox handlers")
Signed-off-by: Angela Czubak <aczubak@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230105160107.17638-1-hkelam@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
OcteonTx2's next gen platform the CN10KB has RPM_USX MAC which has a
different serdes when compared to RPM MAC. Though the underlying
HW is different, the CSR interface has been designed largely inline
with RPM MAC, with few exceptions though. So we are using the same
CGX driver for RPM_USX MAC as well and will have a different set of APIs
for RPM_USX where ever necessary.
The RPM and RPM_USX blocks support a different number of LMACS.
RPM_USX support 8 LMACS per MAC block whereas legacy RPM supports only 4
LMACS per MAC. with this RPM_USX support double the number of DMAC filters
and fifo size.
This patch adds initial support for CN10KB's RPM_USX MAC i.e registering
the driver and defining MAC operations (mac_ops). Adds the logic to
configure internal loopback and pause frames and assign FIFO length to
LMACS.
Kernel reads lmac features like lmac type, autoneg, etc from shared
firmware data this structure only supports 4 lmacs per MAC, this patch
extends this structure to accommodate 8 lmacs.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Most of the code in CGX/RPM driver assumes that max lmacs per
given MAC as always, 4 and the number of MAC blocks also as 4.
With this assumption, the max number of interfaces supported is
hardcoded to 16. This creates a problem as next gen CN10KB silicon
MAC supports 8 lmacs per MAC block.
This patch solves the problem by using "max lmac per MAC block"
value from constant csrs and uses cgx_cnt_max value which is
populated based number of MAC blocks supported by silicon.
Signed-off-by: Rakesh Babu Saladi <rsaladi2@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Set the maximum time firmware should poll for a link.
If not set firmware could block CPU for a long time resulting
in mailbox failures. If link doesn't come up within 1second,
firmware will anyway notify the status as and when LINK comes up
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha Sowjanya <gakula@marvell.com>
Link: https://lore.kernel.org/r/20220712161815.12621-1-gakula@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
CN10K MAC block (RPM) and Octeontx2 MAC block (CGX) both supports
PFC flow control and 802.3X flow control pause frames.
Each MAC block supports max 4 LMACS and AF driver assigns same
(MAC,LMAC) to PF and its VFs. As PF and its share same (MAC,LMAC)
pair we need resource management to address below scenarios
1. Maintain PFC and 8023X pause frames mutually exclusive.
2. Reject disable flow control request if other PF or Vfs
enabled it.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prirority based flow control (802.1Qbb) mechanism is similar to
ethernet pause frames (802.3x) instead pausing all traffic on a link,
PFC allows user to selectively pause traffic according to its class.
Oceteontx2 MAC block (CGX) and CN10K Mac block (RPM) both supports
PFC. As upper layer mbox handler is same for both the MACs, this
patch configures PFC by calling apporopritate callbacks.
Signed-off-by: Sunil Kumar Kori <skori@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixed inconsistent license text across the RVU admin
function driver.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add debugfs support to display CGX/RPM DMAC filter
table associated with pf.
cat /sys/kernel/debug/octeontx2/cgx/cgx0/lmac0/mac_filter
PCI dev RVUPF BROADCAST MULTICAST FILTER-MODE
0002:02:00.0 PF2 ACCEPT ACCEPT UNICAST
DMAC-INDEX ADDRESS
0 00:0f:b7:06:17:06
1 1a:1b:1c:1d:1e:01
2 1a:1b:1c:1d:1e:02
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MAC block supports 32 dmac filters which are logically
divided among all attached LMACS.
For example MAC block0 having one LMAC then maximum supported
filters are 32 where as MAC block1 having 4 enabled LMACS
them maximum supported filteres are 8 for each LMAC.
This patch adds mbox handlers to add/delete/update mac entry
in DMAC filter table.
Signed-off-by: Sunil Kumar Kori <skori@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RPM supports below list of counters as an extension to existing counters
* class based flow control pause frames
* vlan/jabber/fragmented packets
* fcs/alignment/oversized error packets
This patch adds support to display supported RPM counters via debugfs
and define new mbox rpm_stats to read all support counters.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <Sunil.Goutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
OcteonTx3 CN10K silicon supports bigger MTU when compared
to 9216 MTU supported by OcteonTx2 silicon variants. Lookback
interface supports upto 64K and RPM LMAC interfaces support
upto 16K.
This patch does the necessary configuration and adds support
for PF/VF drivers to retrieve max packet size supported via mbox
This patch also configures tx link credit by considering supported
fifo size and max packet length for Octeontx3 silicon.
This patch also removes platform specific name from the driver name.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NIX uses unique channel numbers to identify the packet sources/sinks
like CGX,LBK and SDP. The channel numbers assigned to each block are
hardwired in CN9xxx silicon.
The fixed channel numbers in CN9xxx are:
0x0 | a << 8 | b - LBK(0..3)_CH(0..63)
0x0 | a << 8 - Reserved
0x700 | a - SDP_CH(0..255)
0x800 | a << 8 | b << 4 | c - CGX(0..7)_LMAC(0..3)_CH(0..15)
All the channels in the above fixed enumerator(with maximum
number of blocks) are not required since some chips
have less number of blocks.
For CN10K silicon the channel numbers need to be programmed by
software in each block with the base channel number and range of
channels. This patch calculates and assigns the channel numbers
to efficiently distribute the channel number range(0-4095) among
all the blocks. The assignment is made based on the actual number of
blocks present and also contiguously leaving no holes.
The channel numbers remaining after the math are used as new CPT
replay channels present in CN10K. Also since channel numbers are
not fixed the transmit channel link number needed by AF consumers
is calculated by AF and sent along with nix_lf_alloc mailbox response.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
OcteonTx2's next gen platform the CN10K has RPM MAC which has a
different serdes when compared to CGX MAC. Though the underlying
HW is different, the CSR interface has been designed largely inline
with CGX MAC, with few exceptions though. So we are using the same
CGX driver for RPM MAC as well and will have a different set of APIs
for RPM where ever necessary.
This patch adds initial support for CN10K's RPM MAC i.e. the driver
registration, communication with firmware etc. For communication with
firmware, RPM provides a different IRQ when compared to CGX.
The CGX and RPM blocks support different features. Currently few
features like ptp, flowcontrol and higig are not supported by RPM. This
patch adds new mailbox message "CGX_FEATURES_GET" to get the list of
features supported by underlying MAC.
RPM has different implementations for RX/TX stats. Unlike CGX,
bar offset of stat registers are different. This patch adds
support to access the same and dump the values in debugfs.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CGX LMAC, the physical interface support link configuration parameters
like speed, auto negotiation, duplex etc. Firmware saves these into
memory region shared between firmware and this driver.
This patch adds mailbox handler set_link_mode, fw_data_get to
configure and read these parameters.
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support to fetch fec stats from PHY. The stats are
put in the shared data struct fwdata. A PHY driver indicates
that it has FEC stats by setting the flag fwdata.phy.misc.has_fec_stats
Besides CGX_CMD_GET_PHY_FEC_STATS, also add CGX_CMD_PRBS and
CGX_CMD_DISPLAY_EYE to enum cgx_cmd_id so that Linux's enum list is in sync
with firmware's enum list.
Signed-off-by: Felix Manlunas <fmanlunas@marvell.com>
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CGX block supports forward error correction modes baseR
and RS. This patch adds support to set encoding mode
and to read corrected/uncorrected block counters
Adds new mailbox handlers set_fec to configure encoding modes
and fec_stats to read counters and also increase mbox timeout
to accomdate firmware command response timeout.
Along with new CGX_CMD_SET_FEC command add other commands to
sync with kernel enum list with firmware.
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Firmware configures NIX block mapping for all CGXs
to achieve maximum throughput. This patch reads
the configuration and create mapping between RVU
PF and NIX blocks. And for LBK VFs assign NIX0 for
even numbered VFs and NIX1 for odd numbered VFs.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Rakesh Babu <rsaladi2@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Four new mbox messages ids and handler are added in order to
enable or disable timestamping procedure on tx and rx side.
Additionally when PTP is enabled, the packet parser must skip
over 8 bytes and start analyzing packet data there. To make NPC
profiles work seemlesly PTR_ADVANCE of IKPU is set so that
parsing can be done as before when all data pointers
are shifted by 8 bytes automatically.
Co-developed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Zyta Szpak <zyta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For retrieving info like interface MAC addresses, packet
parser key extraction config etc currently a command
is sent to firmware and firmware which periodically polls
for commands, processes these and returns the info.
This is resulting in interface initialization taking lot
of time. To optimize this a memory region is shared between
firmware and this driver, firmware while booting puts
static info like these into that region for driver to
read directly without using commands.
With this
- Logic for retrieving packet parser extraction config
via commands is removed and repalced with using the
shared 'fwdata' structure.
- Now RVU MSIX vector address is also retrieved from this fwdata struct
instead of from CSR. Otherwise when kexec/kdump crash kernel loads
CSR will have a IOVA setup by primary kernel which impacts
RVU PF/VF's interrupts.
- Also added a mbox handler for PF/VF interfaces to retrieve their MAC
addresses from AF.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Rakesh Babu <rsaladi2@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CGX LMAC, the physical interface can generate pause frames when
internal resources asserts backpressure due to exhaustion.
This patch configures CGX to generate 802.3 pause frames.
Also enabled processing of received pause frames on the line which
will assert backpressure on the internal transmit path.
Also added mailbox handlers for PF drivers to enable or disable
pause frames anytime.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lots of overlapping changes and parallel additions, stuff
like that.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch corrects the SPDX License Identifier style in
header files related to Marvell OcteonTX2 network devices.
It uses an expilict block comment for the SPDX License
Identifier.
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CN96xx initial silicon doesn't support all features pertaining to
NIX transmit scheduling and shaping.
- It supports a fixed topology of 1:1 mapped transmit
limiters at all levels.
- Supports DWRR only at SMQ/MDQ and TL1.
- Doesn't support shaping and coloring.
This patch adds HW capability structure by which each variant
and skew of silicon can be differentiated by their supported
features. And adds support for A0 silicon's transmit scheduler
capabilities or rather limitations.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A CGX port is shared by a RVU PF and it's VFs. These per
CGX port level NIX Rx/Tx counters are cumilative stats of
all NIXLFs sharing this port. These stats when compared
to CGX Rx/Tx stats helps in identifying pkts dropped within
the system, if any.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The following set of NPC registers allow the driver to configure NPC
to generate different key value schemes to compare against packet
payload in MCAM search.
NPC_AF_INTF(0..1)_KEX_CFG
NPC_AF_KEX_LDATA(0..1)_FLAGS_CFG
NPC_AF_INTF(0..1)_LID(0..7)_LT(0..15)_LD(0..1)_CFG
NPC_AF_INTF(0..1)_LDATA(0..1)_FLAGS(0..15)_CFG
Currently, the AF driver populates these registers to
configure the default values to address the most common
use cases such as key generation for channel number + DMAC.
The secure firmware stores different configuration
value of these registers to enable different NPC use case
along with the name for the lookup.
Patch loads profile binary from secure firmware over
the exiting CGX mailbox interface and apply the profile.
AF driver shall fall back to the default configuration
in case of any errors.
The AF consumer driver can know the selected profile
on response to NPC_GET_KEX_CFG mailbox by introducing
mkex_pfl_name in the struct npc_get_kex_cfg_rsp.
Signed-off-by: Vamsi Attunuru <vamsi.attunuru@marvell.com>
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Added new CGX firmware interface API for sending link up/down
commands
- Do link up for cgx lmac ports by default at the time of CGX
driver probe. Since cgx link up in driver probe affects the
Linux boot time, linkup procedure is kept threaded using
workqueues.
For this, a new cgx API cgx_lmac_linkup_start has been added.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added provision to unregister cgx event callbacks.
This enables the exit path to ensure event callbacks are
unregistered before workqueues get destroyed.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For this, cgx_id(struct cgx) definition has been changed to
reflect cgx port id instead of device instance id.
Now cgx_id can be directly used as channel offset for NPC configuration.
Assumptions on contiguous cgx port ids has been removed from
nix_calibrate_x2p as well.
As a side effect, allocation of conversion tables that were based
on cgx count are changed to cgx port id max value.
Tables would return NULL for invalid cgx ports.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* Do CGX init before NIX init
This would add consistency in NIX code that depends on cgx ports
* Few other misc cleanups
- rvu_cgx_probe renamed as rvu_cgx_init for consistency
- rvu_cgx_exit wrapper added to take care of the exit path
- Added error check on cgx_lmac_event_handler_init
- Minor cleanups in cgx.h related to tab alignment
- Removed redundant ids from enum cgx_cmd_id
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for RVU PF/VFs to modify min/max
packet lengths allowed by HW. For VFs on PF0, settings will
be automatically applied on LBK link. RX link's min/maxlen
is configured to min/max of PF and it's all VFs. On the TX side
if requested all SMQs attached to the requesting NIXLF will be
updated with new min/max lengths.
Also updates transmit credits for Tx links based on new maxlen.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For each CGX LMAC that is mapped to a RVU PF, allocate
a pkind and config the same in CGX. For a received packet
at CGX LMAC interface this pkind is used by NPC block
to start parsing of packet.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support to enable or disable internal loopback mode in CGX.
New mbox IDs CGX_INTLBK_ENABLE/DISABLE added for this.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Upon receiving notification from firmware the CGX event handler
in the AF driver gets the current link info such as status, speed,
duplex etc from CGX driver and sends it across to PFs who have
registered to receive such notifications.
To support above
- Mbox messaging support for sending msgs from AF to PF has been added.
- Added mbox msgs so that PFs can register/unregister for link events.
- Link notifications are sent to PF under two scenarioss.
1. When a asynchronous link change notification is received from
firmware with notification flag turned on for that PF.
2. Upon notification turn on request, the current link status is
send to the PF.
Also added a new mailbox msg using which RVU PF/VF can retrieve
their mapped CGX LMAC's current link info. Link info includes
status, speed, duplex and lmac type.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for setting MAC address filters in CGX
for PF interfaces. Also PF interfaces can be put in promiscuous
mode. Dataplane PFs access this functionality using mailbox
messages to the AF driver.
Signed-off-by: Vidhya Raman <vraman@marvell.com>
Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for a RVU PF/VF driver to retrieve
it's mapped CGX LMAC Rx and Tx stats from AF via mbox.
New mailbox msg is added is added.
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added new mailbox msgs for RVU PF/VFs to request AF
to enable/disable their mapped CGX::LMAC Rx & Tx.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CGX LMAC initialization, link status polling etc is done
by low level secure firmware. For link management this patch
adds a interface or communication mechanism between firmware
and this kernel CGX driver.
- Firmware interface specification is defined in cgx_fw_if.h.
- Support to send/receive commands/events to/form firmware.
- events/commands implemented
* link up
* link down
* reading firmware version
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Nithya Mani <nmani@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each of the enabled CGX LMAC is considered a physical
interface and RVU PFs are mapped to these. VFs of these
SRIOV PFs will be virtual interfaces and share CGX LMAC
along with PF.
This mapping info will be used later on for Rx/Tx pkt steering.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds basic template for Marvell OcteonTX2's
CGX ethernet interface driver. Just the probe.
RVU AF driver will use APIs exported by this driver
for various things like PF to physical interface mapping,
loopback mode, interface stats etc. Hence marged both
drivers into a single module.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
