summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/micrel/ks8851.c
AgeCommit message (Collapse)Author
2020-05-28net: ks8851: Separate SPI operations into separate fileMarek Vasut
Pull all the SPI bus specific code into a separate file, so that it is not mixed with the common code. Rename ks8851.c to ks8851_common.c. The ks8851_common.c is linked with ks8851_spi.c now, so it can call the accessors in the ks8851_spi.c without any pointer indirection. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-28net: ks8851: Implement register, FIFO, lock accessor callbacksMarek Vasut
The register and FIFO accessors are bus specific, so is locking. Implement callbacks so that each variant of the KS8851 can implement matching accessors and locking, and use the rest of the common code. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-28net: ks8851: Permit overridding interrupt enable registerMarek Vasut
The parallel bus variant does not need to use the TX interrupt at all as it writes the TX FIFO directly with in .ndo_start_xmit, permit the drivers to configure the interrupt enable bits. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-28net: ks8851: Factor out TX work flush functionMarek Vasut
While the SPI version of the KS8851 requires a TX worker thread to pump data via SPI, the parallel bus version can write data into the TX FIFO directly in .ndo_start_xmit, as the parallel bus access is much faster and does not sleep. Factor out this TX work flush part, so it can be overridden by the parallel bus driver. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-28net: ks8851: Split out SPI specific code from probe() and remove()Marek Vasut
Factor out common code into ks8851_probe_common() and ks8851_remove_common() to permit both SPI and parallel bus driver variants to use the common code path for both probing and removal. There should be no functional change. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-28net: ks8851: Split out SPI specific entries in struct ks8851_netMarek Vasut
Add a new struct ks8851_net_spi, which embeds the original struct ks8851_net and contains the entries specific only to the SPI variant of KS8851. There should be no functional change. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-28net: ks8851: Factor out SKB receive functionMarek Vasut
Factor out this netif_rx_ni(), so it could be overridden by the parallel bus variant of the KS8851 driver. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-28net: ks8851: Factor out bus lock handlingMarek Vasut
Pull out bus access locking code into separate functions, this is done in preparation for unifying the driver with the parallel bus one. The parallel bus driver does not need heavy mutex locking of the bus and works better with spinlocks, hence prepare these locking functions to be overridden then. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-28net: ks8851: Use 16-bit read of RXFC registerMarek Vasut
The RXFC register is the only one being read using 8-bit accessors. To make it easier to support the 16-bit accesses used by the parallel bus variant of KS8851, use 16-bit accessor to read RXFC register as well as neighboring RXFCTR register. Remove ks8851_rdreg8() as it is not used anywhere anymore. There should be no functional change. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-28net: ks8851: Use 16-bit writes to program MAC addressMarek Vasut
On the SPI variant of KS8851, the MAC address can be programmed with either 8/16/32-bit writes. To make it easier to support the 16-bit parallel option of KS8851 too, switch both the MAC address programming and readout to 16-bit operations. Remove ks8851_wrreg8() as it is not used anywhere anymore. There should be no functional change. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-28net: ks8851: Remove ks8851_rdreg32()Marek Vasut
The ks8851_rdreg32() is used only in one place, to read two registers using a single read. To make it easier to support 16-bit accesses via parallel bus later on, replace this single read with two 16-bit reads from each of the registers and drop the ks8851_rdreg32() altogether. If this has noticeable performance impact on the SPI variant of KS8851, then we should consider using regmap to abstract the SPI and parallel bus options and in case of SPI, permit regmap to merge register reads of neighboring registers into single, longer, read. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-28net: ks8851: Use dev_{get,set}_drvdata()Marek Vasut
Replace spi_{get,set}_drvdata() with dev_{get,set}_drvdata(), which works for both SPI and platform drivers. This is done in preparation for unifying the KS8851 SPI and parallel bus drivers. There should be no functional change. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-28net: ks8851: Use devm_alloc_etherdev()Marek Vasut
Use device managed version of alloc_etherdev() to simplify the code. No functional change intended. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-28net: ks8851: Pass device node into ks8851_init_mac()Marek Vasut
Since the driver probe function already has a struct device *dev pointer and can easily derive of_node pointer from it, pass the of_node pointer as a parameter to ks8851_init_mac() to avoid fishing it out from ks->spidev. This is the only reference to spidev in the function, so get rid of it. This is done in preparation for unifying the KS8851 SPI and parallel bus drivers. No functional change. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-28net: ks8851: Replace dev_err() with netdev_err() in IRQ handlerMarek Vasut
Use netdev_err() instead of dev_err() to avoid accessing the spidev->dev in the interrupt handler. This is the only place which uses the spidev in this function, so replace it with netdev_err() to get rid of it. This is done in preparation for unifying the KS8851 SPI and parallel drivers. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-28net: ks8851: Rename ndev to netdev in probeMarek Vasut
Rename ndev variable to netdev for the sake of consistency. No functional change. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-28net: ks8851: Factor out spi->dev in probe()/remove()Marek Vasut
Pull out the spi->dev into one common place in the function instead of having it repeated over and over again. This is done in preparation for unifying ks8851 and ks8851-mll drivers. No functional change. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-19treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500Thomas Gleixner
Based on 2 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation # extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 4122 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Enrico Weigelt <info@metux.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-10net: ethernet: fix similar warning reported by kbuild test robotPetr Štetiar
This patch fixes following (similar) warning reported by kbuild test robot: In function ‘memcpy’, inlined from ‘smsc75xx_init_mac_address’ at drivers/net/usb/smsc75xx.c:778:3, inlined from ‘smsc75xx_bind’ at drivers/net/usb/smsc75xx.c:1501:2: ./include/linux/string.h:355:9: warning: argument 2 null where non-null expected [-Wnonnull] return __builtin_memcpy(p, q, size); ^~~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/net/usb/smsc75xx.c: In function ‘smsc75xx_bind’: ./include/linux/string.h:355:9: note: in a call to built-in function ‘__builtin_memcpy’ I've replaced the offending memcpy with ether_addr_copy, because I'm 100% sure, that of_get_mac_address can't return NULL as it returns valid pointer or ERR_PTR encoded value, nothing else. I'm hesitant to just change IS_ERR into IS_ERR_OR_NULL check, as this would make the warning disappear also, but it would be confusing to check for impossible return value just to make a compiler happy. I'm now changing all occurencies of memcpy to ether_addr_copy after the of_get_mac_address call, as it's very likely, that we're going to get similar reports from kbuild test robot in the future. Fixes: a51645f70f63 ("net: ethernet: support of_get_mac_address new ERR_PTR error") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-07net: ethernet: support of_get_mac_address new ERR_PTR errorPetr Štetiar
There was NVMEM support added to of_get_mac_address, so it could now return ERR_PTR encoded error values, so we need to adjust all current users of of_get_mac_address to this new fact. While at it, remove superfluous is_valid_ether_addr as the MAC address returned from of_get_mac_address is always valid and checked by is_valid_ether_addr anyway. Fixes: d01f449c008a ("of_net: add NVMEM support to of_get_mac_address") Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-20net: ks8851: Deduplicate register macrosLukas Wunner
The ks8851 chip is sold either with an SPI interface (KSZ8851SNL) or with a so-called non-PCI interface (KSZ8851-16MLL). When the driver for the latter was introduced with commit a55c0a0ed415 ("drivers/net: ks8851_mll ethernet network driver"), it duplicated the register macros introduced by the driver for the former with commit 3ba81f3ece3c ("net: Micrel KS8851 SPI network driver"). The chips are almost identical, so the duplication seems unwarranted. There are a handful of bits which are in use on the KSZ8851-16MLL but reserved on the KSZ8851SNL, and vice-versa, but there are no actual collisions. Thus, remove the duplicate definitions from the KSZ8851-16MLL driver. Mark all bits which differ between the two chips. Move the SPI frame opcodes, which are specific to KSZ8851SNL, to its driver. The KSZ8851-16MLL driver added a RXFCTR_THRESHOLD_MASK macro which is a duplication of the RXFCTR_RXFCT_MASK macro, rename it where it's used. Same for P1MBCR_FORCE_FDX, which duplicates the BMCR_FULLDPLX macro and OBCR_ODS_16MA, which duplicates OBCR_ODS_16mA. Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: Frank Pavlic <f.pavlic@kunbus.de> Cc: Ben Dooks <ben.dooks@codethink.co.uk> Cc: Tristram Ha <Tristram.Ha@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-20net: ks8851: Set initial carrier state to downLukas Wunner
The ks8851 chip's initial carrier state is down. A Link Change Interrupt is signaled once interrupts are enabled if the carrier is up. The ks8851 driver has it backwards by assuming that the initial carrier state is up. The state is therefore misrepresented if the interface is opened with no cable attached. Fix it. The Link Change interrupt is sometimes not signaled unless the P1MBSR register (which contains the Link Status bit) is read on ->ndo_open(). This might be a hardware erratum. Read the register by calling mii_check_link(), which has the desirable side effect of setting the carrier state to down if the cable was detached while the interface was closed. Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: Frank Pavlic <f.pavlic@kunbus.de> Cc: Ben Dooks <ben.dooks@codethink.co.uk> Cc: Tristram Ha <Tristram.Ha@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-20net: ks8851: Delay requesting IRQ until openedLukas Wunner
The ks8851 driver currently requests the IRQ before registering the net_device. Because the net_device name is used as IRQ name and is still "eth%d" when the IRQ is requested, it's impossibe to tell IRQs apart if multiple ks8851 chips are present. Most other drivers delay requesting the IRQ until the net_device is opened. Do the same. The driver doesn't enable interrupts on the chip before opening the net_device and disables them when closing it, so there doesn't seem to be a need to request the IRQ already on probe. Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: Frank Pavlic <f.pavlic@kunbus.de> Cc: Ben Dooks <ben.dooks@codethink.co.uk> Cc: Tristram Ha <Tristram.Ha@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-20net: ks8851: Reassert reset pin if chip ID check failsLukas Wunner
Commit 73fdeb82e963 ("net: ks8851: Add optional vdd_io regulator and reset gpio") amended the ks8851 driver to briefly assert the chip's reset pin on probe. It also amended the probe routine's error path to reassert the reset pin if a subsequent initialization step fails. However the commit misplaced reassertion of the reset pin in the error path such that it is not performed if the check of the Chip ID and Enable Register (CIDER) fails. The error path is therefore slightly asymmetrical to the probe routine's body. Fix it. Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: Frank Pavlic <f.pavlic@kunbus.de> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Nishanth Menon <nm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-20net: ks8851: Dequeue RX packets explicitlyLukas Wunner
The ks8851 driver lets the chip auto-dequeue received packets once they have been read in full. It achieves that by setting the ADRFE flag in the RXQCR register ("Auto-Dequeue RXQ Frame Enable"). However if allocation of a packet's socket buffer or retrieval of the packet over the SPI bus fails, the packet will not have been read in full and is not auto-dequeued. Such partial retrieval of a packet confuses the chip's RX queue management: On the next RX interrupt, the first packet read from the queue will be the one left there previously and this one can be retrieved without issues. But for any newly received packets, the frame header status and byte count registers (RXFHSR and RXFHBCR) contain bogus values, preventing their retrieval. The chip allows explicitly dequeueing a packet from the RX queue by setting the RRXEF flag in the RXQCR register ("Release RX Error Frame"). This could be used to dequeue the packet in case of an error, but if that error is a failed SPI transfer, it is unknown if the packet was transferred in full and was auto-dequeued or if it was only transferred in part and requires an explicit dequeue. The safest approach is thus to always dequeue packets explicitly and forgo auto-dequeueing. Without this change, I've witnessed packet retrieval break completely when an SPI DMA transfer fails, requiring a chip reset. Explicit dequeueing magically fixes this and makes packet retrieval absolutely robust for me. The chip's documentation suggests auto-dequeuing and uses the RRXEF flag only to dequeue error frames which the driver doesn't want to retrieve. But that seems to be a fair-weather approach. Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: Frank Pavlic <f.pavlic@kunbus.de> Cc: Ben Dooks <ben.dooks@codethink.co.uk> Cc: Tristram Ha <Tristram.Ha@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-19net: ks8851: Support DT-provided MAC addressLukas Wunner
Allow the boot loader to specify the MAC address in the device tree to override the EEPROM, or in case no EEPROM is present. Cc: Ben Dooks <ben@simtec.co.uk> Cc: Tristram Ha <tristram.ha@micrel.com> Cc: David J. Choi <david.choi@micrel.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-05net/{mii, smsc}: Make mii_ethtool_get_link_ksettings and smc_netdev_get_ecmd ↵yuval.shaia@oracle.com
return void Make return value void since functions never returns meaningfull value. Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-09net: ks8851: Added support for half-duplex SPISergey Shcherbakov
In original driver was implemented support for half- and full-duplex modes, but it was not enabled. Instead of it ks8851_rx_1msg method always returns "true" that means "full-duplex" mode. This patch replaces hard-coded functionality with flexible solution that supports both SPI modes. Signed-off-by: Sergey Shcherbakov <shchers@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-12net: micrel: ks8851: use new api ethtool_{get|set}_link_ksettingsPhilippe Reynes
The ethtool api {get|set}_settings is deprecated. We move this driver to new api {get|set}_link_ksettings. As I don't have the hardware, I'd be very pleased if someone may test this patch. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-01-24net: ks8851: Drop eeprom_size structure memberStephen Boyd
After commit 51b7b1c34e19 (KSZ8851-SNL: Add ethtool support for EEPROM via eeprom_93cx6, 2011-11-21) this structure member is unused. Delete it. Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-10-13net: deprecate eth_change_mtu, remove usageJarod Wilson
With centralized MTU checking, there's nothing productive done by eth_change_mtu that isn't already done in dev_set_mtu, so mark it as deprecated and remove all usage of it in the kernel. All callers have been audited for calls to alloc_etherdev* or ether_setup directly, which means they all have a valid dev->min_mtu and dev->max_mtu. Now eth_change_mtu prints out a netdev_warn about being deprecated, for the benefit of out-of-tree drivers that might be utilizing it. Of note, dvb_net.c actually had dev->mtu = 4096, while using eth_change_mtu, meaning that if you ever tried changing it's mtu, you couldn't set it above 1500 anymore. It's now getting dev->max_mtu also set to 4096 to remedy that. v2: fix up lantiq_etop, missed breakage due to drive not compiling on x86 CC: netdev@vger.kernel.org Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-11-04Merge remote-tracking branches 'spi/topic/omap-100k', ↵Mark Brown
'spi/topic/omap-uwire', 'spi/topic/owner', 'spi/topic/pxa' and 'spi/topic/pxa2xx' into spi-next
2015-10-28spi: Drop owner assignment from spi_driversAndrew F. Davis
An spi_driver does not need to set an owner, it will be populated by the driver core. Signed-off-by: Andrew F. Davis <afd@ti.com> Acked-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org>
2015-09-17net: ks8851: Export OF module alias informationJavier Martinez Canillas
Drivers needs to export the OF id table and this be built into the module or udev won't have the necessary information to autoload the driver module when the device is registered via OF. Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-02net: ks8851: Don't use regulator_get_optional()Stephen Boyd
We shouldn't be using regulator_get_optional() here. These regulators are always present as part of the physical design and there isn't any way to use an internal regulator or change the source of the reference voltage via software. Given that the only users of this driver in the kernel are DT based, this change should be transparent to them even if they don't specify any supplies because the regulator framework will insert dummy supplies as needed. Cc: Nishanth Menon <nm@ti.com> Cc: Mark Brown <broonie@kernel.org> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-01net: Revert mlx4 cpumask changes.David S. Miller
This reverts commit 70a640d0dae3a9b1b222ce673eb5d92c263ddd61 ("net/mlx4_en: Use affinity hint") and commit c8865b64b05b2f4eeefd369373e9c8aeb069e7a1 ("cpumask: Utility function to set n'th cpu - local cpu first") because these changes break the build when SMP is disabled amongst other things. Reported-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-06-01net: ks8851: Don't use regulator_get_optional()Stephen Boyd
We shouldn't be using regulator_get_optional() here. These regulators are always present as part of the physical design and there isn't any way to use an internal regulator or change the source of the reference voltage via software. Given that the only users of this driver in the kernel are DT based, this change should be transparent to them even if they don't specify any supplies because the regulator framework will insert dummy supplies as needed. Cc: Nishanth Menon <nm@ti.com> Cc: Mark Brown <broonie@kernel.org> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-24net: ks8851: Add of match tableStephen Boyd
Users are currently just providing "ks8851" as the compatible for this driver in device tree. Add a compatible string that provides the vendor name along with the device name to be more explicit. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-24net: ks8851: Add optional vdd_io regulator and reset gpioStephen Boyd
Allow the ks8851 driver to enable an optional 1.8V vdd_io regulator and assert the reset pin to the phy if a reset gpio is present in device tree. Cc: Nishanth Menon <nm@ti.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-24net: ks8851: Use devm_regulator_get_optional()Stephen Boyd
This simplifies error paths and removes the need to regulator_put(). Cc: Nishanth Menon <nm@ti.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-13net: get rid of SET_ETHTOOL_OPSWilfried Klaebe
net: get rid of SET_ETHTOOL_OPS Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone. This does that. Mostly done via coccinelle script: @@ struct ethtool_ops *ops; struct net_device *dev; @@ - SET_ETHTOOL_OPS(dev, ops); + dev->ethtool_ops = ops; Compile tested only, but I'd seriously wonder if this broke anything. Suggested-by: Dave Miller <davem@davemloft.net> Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de> Acked-by: Felipe Balbi <balbi@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-24net: micrel : ks8851-ml: add vdd-supply supportNishanth Menon
Few platforms use external regulator to keep the ethernet MAC supplied. So, request and enable the regulator for driver functionality. Fixes: 66fda75f47dc (regulator: core: Replace direct ops->disable usage) Reported-by: Russell King <rmk+kernel@arm.linux.org.uk> Suggested-by: Markus Pargmann <mpa@pengutronix.de> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-16ks8851: Remove unneeded PM_OPS definitionsFabio Estevam
SIMPLE_DEV_PM_OPS macro can handle !CONFIG_PM_SLEEP case nicely, so there is no need to define PM_OPS for both CONFIG_PM_SLEEP and !CONFIG_PM_SLEEP cases. Remove the unneeded definitions. Cc: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-08net: ks8851: Use dev_pm_opsLars-Peter Clausen
Use dev_pm_ops instead of the deprecated legacy suspend/resume callbacks. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-08net: ks8851: Use module_spi_driverLars-Peter Clausen
By using module_spi_driver we can eliminate a few lines of boilerplate code. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-07net: ethernet: ks8851: use spi_get_drvdata() and spi_set_drvdata()Jingoo Han
Use the wrapper functions for getting and setting the driver data using spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we can directly pass a struct spi_device. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-29ks8851: Fix interpretation of rxlen field.Max.Nekludov@us.elster.com
According to the Datasheet (page 52): 15-12 Reserved 11-0 RXBC Receive Byte Count This field indicates the present received frame byte size. The code has a bug: rxh = ks8851_rdreg32(ks, KS_RXFHSR); rxstat = rxh & 0xffff; rxlen = rxh >> 16; // BUG!!! 0xFFF mask should be applied Signed-off-by: Max Nekludov <Max.Nekludov@us.elster.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-29net: ks8851: convert to threaded IRQFelipe Balbi
just as it should have been. It also helps removing the, now unnecessary, workqueue. Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-03net: remove unnecessary NET_ADDR_RANDOM "bitclean"Jiri Pirko
NET_ADDR_SET is set in dev_set_mac_address() no need to alter dev->addr_assign_type value in drivers. Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-12-03net/micrel: remove __dev* attributesBill Pemberton
CONFIG_HOTPLUG is going away as an option. As result the __dev* markings will be going away. Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst, and __devexit. Signed-off-by: Bill Pemberton <wfp5p@virginia.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>