| Age | Commit message (Collapse) | Author |
|---|
|
The "read-modify-write register index" function is declared with a
confusing prototype: the "mask" and "reg" arguments are swapped.
Fortunately, this does not affect callers so far. Both arguments are
u32, and the wrapper macros (ocelot_rmw_ix etc) have the arguments in
the correct order (the one from ocelot_io.c).
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for PTP Hardware Clock (PHC) to the Ocelot
switch for both PTP 1-step and 2-step modes.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In struct frame_info, the cpuq member is never used. This cosmetic patch
removes it from the structure, and from the parsing of the frame header
as it's only set but never used.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for using the PTP register range, and adds a
description of its registers. This bank is used when configuring PTP.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ACL support using the TCAM. Using ACL it is possible to create rules
in hardware to filter/redirect frames.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The phylink conflict was between a bug fix by Russell King
to make sure we have a consistent PHY interface mode, and
a change in net-next to pull some code in phylink_resolve()
into the helper functions phylink_mac_link_{up,down}()
On the dp83867 side it's mostly overlapping changes, with
the 'net' side removing a condition that was supposed to
trigger for RGMII but because of how it was coded never
actually could trigger.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hardware offload of matchall classifier and police action are now
supported via the tc command.
Supported police parameters are: rate and burst.
Example:
Add:
tc qdisc add dev eth3 handle ffff: ingress
tc filter add dev eth3 parent ffff: prio 1 handle 2 \
matchall skip_sw \
action police rate 100Mbit burst 10000
Show:
tc -s -d qdisc show dev eth3
tc -s -d filter show dev eth3 ingress
Delete:
tc filter del dev eth3 parent ffff: prio 1
tc qdisc del dev eth3 handle ffff: ingress
Signed-off-by: Joergen Andreasen <joergen.andreasen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Doing kmalloc in atomic context is always an issue,
more so for a list that can grow significantly.
Turns out that the driver only uses the duplicated
list of multicast mac addresses to keep track of
what addresses to delete from h/w before committing
the new list from kernel to h/w back again via set_rx_mode,
every time this list gets updated by the kernel.
Given that the h/w knows how to add and delete mac addresses
based on the mac address value alone, __dev_mc_sync should be
the much better choice of kernel API for these operations
avoiding the considerable overhead of maintaining a duplicated
list in the driver.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Following patches will change the way we communicate setting a port's
attribute and use notifiers to perform those tasks.
Ocelot does not currently have an atomic notifier registered for
switchdev events, so we need to register one in order to deal with
atomic context SWITCHDEV_PORT_ATTR_SET events.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Following patches will change the way of distributing port object
changes from a switchdev operation to a switchdev notifier. The
switchdev code currently recursively descends through layers of lower
devices, eventually calling the op on a front-panel port device. The
notifier will instead be sent referencing the bridge port device, which
may be a stacking device that's one of front-panel ports uppers, or a
completely unrelated device.
Dispatch the new events to ocelot_port_obj_add() resp. _del() to
maintain the same behavior that the switchdev operation based code
currently has. Pass through switchdev_handle_port_obj_add() / _del() to
handle the recursive descend, because Ocelot supports LAG uppers.
Register to the new switchdev blocking notifier chain to get the new
events when they start getting distributed.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, the SerDes muxing was hardcoded to a given mode in the MAC
controller driver. Now, the SerDes muxing is configured within the
Device Tree and is enforced in the MAC controller driver so we can have
a lot of different SerDes configurations.
Make use of the SerDes PHYs in the MAC controller to set up the SerDes
according to the SerDes<->switch port mapping and the communication mode
with the Ethernet PHY.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since HSIO address space can be accessed by different drivers, let's
simplify the register address definitions so that it can be easily used
by all drivers and put the register address definition in the
include/soc/mscc/ocelot_hsio.h header file.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since HSIO address space can be used by different drivers (PLL, SerDes
muxing, temperature sensor), let's move it somewhere it can be included
by all drivers.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add link aggregation hardware offload support for Ocelot.
ocelot_get_link_ksettings() is not great but it does work until the driver
is reworked to switch to phylink.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a driver for Microsemi Ocelot Ethernet switch support.
This makes two modules:
mscc_ocelot_common handles all the common features that doesn't depend on
how the switch is integrated in the SoC. Currently, it handles offloading
bridging to the hardware. ocelot_io.c handles register accesses. This is
unfortunately needed because the register layout is packed and then depends
on the number of ports available on the switch. The register definition
files are automatically generated.
ocelot_board handles the switch integration on the SoC and on the board.
Frame injection and extraction to/from the CPU port is currently done using
register accesses which is quite slow. DMA is possible but the port is not
able to absorb the whole switch bandwidth.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
