Age | Commit message (Collapse) | Author |
|
Merge in late fixes to prepare for the 6.16 net-next PR.
No conflicts nor adjacent changes.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There is a potential crash issue when disabling and re-enabling the
network port. When disabling the network port, phy_detach() calls
device_link_del() to remove the device link, but it does not clear
phydev->devlink, so phydev->devlink is not a NULL pointer. Then the
network port is re-enabled, but if phy_attach_direct() fails before
calling device_link_add(), the code jumps to the "error" label and
calls phy_detach(). Since phydev->devlink retains the old value from
the previous attach/detach cycle, device_link_del() uses the old value,
which accesses a NULL pointer and causes a crash. The simplified crash
log is as follows.
[ 24.702421] Call trace:
[ 24.704856] device_link_put_kref+0x20/0x120
[ 24.709124] device_link_del+0x30/0x48
[ 24.712864] phy_detach+0x24/0x168
[ 24.716261] phy_attach_direct+0x168/0x3a4
[ 24.720352] phylink_fwnode_phy_connect+0xc8/0x14c
[ 24.725140] phylink_of_phy_connect+0x1c/0x34
Therefore, phydev->devlink needs to be cleared when the device link is
deleted.
Fixes: bc66fa87d4fd ("net: phy: Add link between phy dev and mac dev")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250523083759.3741168-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce new API, genphy_match_phy_device(), to provide a way to check
to match a PHY driver for a PHY device based on the info stored in the
PHY device struct.
The function generalize the logic used in phy_bus_match() to check the
PHY ID whether if C45 or C22 ID should be used for matching.
This is useful for custom .match_phy_device function that wants to use
the generic logic under some condition. (example a PHY is already setup
and provide the correct PHY ID)
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250517201353.5137-5-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pass PHY driver pointer to .match_phy_device OP in addition to phydev.
Having access to the PHY driver struct might be useful to check the
PHY ID of the driver is being matched for in case the PHY ID scanned in
the phydev is not consistent.
A scenario for this is a PHY that change PHY ID after a firmware is
loaded, in such case, the PHY ID stored in PHY device struct is not
valid anymore and PHY will manually scan the ID in the match_phy_device
function.
Having the PHY driver info is also useful for those PHY driver that
implement multiple simple .match_phy_device OP to match specific MMD PHY
ID. With this extra info if the parsing logic is the same, the matching
function can be generalized by using the phy_id in the PHY driver
instead of hardcoding.
Rust wrapper callback is updated to align to the new match_phy_device
arguments.
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Benno Lossin <lossin@kernel.org> # for Rust
Reviewed-by: FUJITA Tomonori <fujita.tomonori@gmail.com>
Link: https://patch.msgid.link/20250517201353.5137-2-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After having factored out the provider part from mdio_bus.c, we can
make the mdio consumer / device layer a separate module. This also
allows to remove Kconfig symbol MDIO_DEVICE.
The module init / exit functions from mdio_bus.c no longer have to be
called from phy_device.c. The link order defined in
drivers/net/phy/Makefile ensures that init / exit functions are called
in the right order.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/dba6b156-5748-44ce-b5e2-e8dc2fcee5a7@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Refactor to check if the fwnode we got is correct and return if so,
otherwise do additional checks. Using same pattern in all conditionals
makes it slightly easier to read and understand.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250430143802.3714405-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add helper which returns the MAC termination resistance value. Modifying
the resistance to an appropriate value can reduce signal reflections and
therefore improve signal quality.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Dimitri Fedrau <dimitri.fedrau@liebherr.com>
Link: https://patch.msgid.link/20250416-dp83822-mac-impedance-v3-3-028ac426cddb@liebherr.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
AFAICS this function has never had a user.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/ab7b8094-2eea-4e82-a047-fd60117f220b@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
phylink-controlled PHY
DSA has 2 kinds of drivers:
1. Those who call dsa_switch_suspend() and dsa_switch_resume() from
their device PM ops: qca8k-8xxx, bcm_sf2, microchip ksz
2. Those who don't: all others. The above methods should be optional.
For type 1, dsa_switch_suspend() calls dsa_user_suspend() -> phylink_stop(),
and dsa_switch_resume() calls dsa_user_resume() -> phylink_start().
These seem good candidates for setting mac_managed_pm = true because
that is essentially its definition [1], but that does not seem to be the
biggest problem for now, and is not what this change focuses on.
Talking strictly about the 2nd category of DSA drivers here (which
do not have MAC managed PM, meaning that for their attached PHYs,
mdio_bus_phy_suspend() and mdio_bus_phy_resume() should run in full),
I have noticed that the following warning from mdio_bus_phy_resume() is
triggered:
WARN_ON(phydev->state != PHY_HALTED && phydev->state != PHY_READY &&
phydev->state != PHY_UP);
because the PHY state machine is running.
It's running as a result of a previous dsa_user_open() -> ... ->
phylink_start() -> phy_start() having been initiated by the user.
The previous mdio_bus_phy_suspend() was supposed to have called
phy_stop_machine(), but it didn't. So this is why the PHY is in state
PHY_NOLINK by the time mdio_bus_phy_resume() runs.
mdio_bus_phy_suspend() did not call phy_stop_machine() because for
phylink, the phydev->adjust_link function pointer is NULL. This seems a
technicality introduced by commit fddd91016d16 ("phylib: fix PAL state
machine restart on resume"). That commit was written before phylink
existed, and was intended to avoid crashing with consumer drivers which
don't use the PHY state machine - phylink always does, when using a PHY.
But phylink itself has historically not been developed with
suspend/resume in mind, and apparently not tested too much in that
scenario, allowing this bug to exist unnoticed for so long. Plus, prior
to the WARN_ON(), it would have likely been invisible.
This issue is not in fact restricted to type 2 DSA drivers (according to
the above ad-hoc classification), but can be extrapolated to any MAC
driver with phylink and MDIO-bus-managed PHY PM ops. DSA is just where
the issue was reported. Assuming mac_managed_pm is set correctly, a
quick search indicates the following other drivers might be affected:
$ grep -Zlr PHYLINK_NETDEV drivers/ | xargs -0 grep -L mac_managed_pm
drivers/net/ethernet/atheros/ag71xx.c
drivers/net/ethernet/microchip/sparx5/sparx5_main.c
drivers/net/ethernet/microchip/lan966x/lan966x_main.c
drivers/net/ethernet/freescale/dpaa2/dpaa2-mac.c
drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c
drivers/net/ethernet/freescale/ucc_geth.c
drivers/net/ethernet/freescale/enetc/enetc_pf_common.c
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
drivers/net/ethernet/marvell/mvneta.c
drivers/net/ethernet/marvell/prestera/prestera_main.c
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/altera/altera_tse_main.c
drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
drivers/net/ethernet/meta/fbnic/fbnic_phylink.c
drivers/net/ethernet/tehuti/tn40_phy.c
drivers/net/ethernet/mscc/ocelot_net.c
Make the existing conditions dependent on the PHY device having a
phydev->phy_link_change() implementation equal to the default
phy_link_change() provided by phylib. Otherwise, we implicitly know that
the phydev has the phylink-provided phylink_phy_change() callback, and
when phylink is used, the PHY state machine always needs to be stopped/
started on the suspend/resume path. The code is structured as such that
if phydev->phy_link_change() is absent, it is a matter of time until the
kernel will crash - no need to further complicate the test.
Thus, for the situation where the PM is not managed by the MAC, we will
make the MDIO bus PM ops treat identically the phylink-controlled PHYs
with the phylib-controlled PHYs where an adjust_link() callback is
supplied. In both cases, the MDIO bus PM ops should stop and restart the
PHY state machine.
[1] https://lore.kernel.org/netdev/Z-1tiW9zjcoFkhwc@shell.armlinux.org.uk/
Fixes: 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
Reported-by: Wei Fang <wei.fang@nxp.com>
Tested-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250407094042.2155633-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In an upcoming change, mdio_bus_phy_may_suspend() will need to
distinguish a phylib-based PHY client from a phylink PHY client.
For that, it will need to compare the phydev->phy_link_change() function
pointer with the eponymous phy_link_change() provided by phylib.
To avoid forward function declarations, the default PHY link state
change method should be moved upwards. There is no functional change
associated with this patch, it is only to reduce the noise from a real
bug fix.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/20250407093900.2155112-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
phy_loopback() leaves it to the PHY driver to select the speed of the
loopback mode. Thus, the speed of the loopback mode depends on the PHY
driver in use.
Add support for speed selection to phy_loopback() to enable loopback
with defined speeds. Ensure that link up is signaled if speed changes
as speed is not allowed to change during link up. Link down and up is
necessary for a new speed.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Link: https://patch.msgid.link/20250312203010.47429-3-gerhard@engleder-embedded.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
PHY drivers support loopback mode, but it is not possible to select the
speed of the loopback mode. The speed is chosen by the set_loopback()
operation of the PHY driver. Same is valid for genphy_loopback().
There are PHYs that support loopback with different speeds. Extend
set_loopback() to make loopback speed selection possible.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250312203010.47429-2-gerhard@engleder-embedded.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When configuring PHY advertising with autoneg disabled, we lookd for an
exact linkmode to advertise and configure for the requested Speed and
Duplex, specially at or over 1G.
Using phy_caps_lookup allows us to build a list of the supported
linkmodes at that speed that we can advertise instead of the first mode
that matches.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-9-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The canonical definition for all the link modes is in linux/ethtool.h,
which is complemented by the link_mode_params array stored in
net/ethtool/common.h . That array contains all the metadata about each
of these modes, including the Speed and Duplex information.
Phylib and phylink needs that information as well for internal
management of the link, which was done by duplicating that information
in locally-stored arrays and lookup functions. This makes it easy for
developpers adding new modes to forget modifying phylib and phylink
accordingly.
However, the link_mode_params array in net/ethtool/common.c is fairly
inefficient to search through, as it isn't sorted in any manner. Phylib
and phylink perform a lot of lookup operations, mostly to filter modes
by speed and/or duplex.
We therefore introduce the link_caps private array in phy_caps.c, that
indexes linkmodes in a more efficient manner. Each element associated a
tuple <speed, duplex> to a bitfield of all the linkmodes runs at these
speed/duplex.
We end-up with an array that's fairly short, easily addressable and that
it optimised for the typical use-cases of phylib/phylink.
That array is initialized at the same time as phylib. As the
link_mode_params array is part of the net stack, which phylink depends
on, it should always be accessible from phylib.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-3-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This patch is the first step in moving the PHY package related code
to its own source file. No functional change intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/57df5c19-fbcd-45a7-9afd-cd4f74d7fa76@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch is a starting point for moving phylib-internal
declarations to a private header file.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/082eacd2-a888-4716-8797-b3491ce02820@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A PHY driver may populate eee_disabled_modes in its probe or get_features
callback, therefore filter the EEE advertisement read from the PHY.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/493f3e2e-9cfc-445d-adbe-58d9c117a489@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add helper which returns the tx amplitude gain defined in device tree.
Modifying it can be necessary to compensate losses on the PCB and
connector, so the voltages measured on the RJ45 pins are conforming.
Signed-off-by: Dimitri Fedrau <dimitri.fedrau@liebherr.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250214-dp83822-tx-swing-v5-2-02ca72620599@liebherr.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Helper phy_is_internal() is just used in two places phylib-internally.
So let's remove it from the API.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/f3f35265-80a9-4ed7-ad78-ae22c21e288b@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Stop exporting feature arrays which aren't used outside phylib.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/01886672-4880-4ca8-b7b0-94d40f6e0ec5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
outside phylib
Certain fixup-related definitions aren't used outside phy_device.c.
So make them private and remove them from phy.h.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/ea6fde13-9183-4c7c-8434-6c0eb64fc72c@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This bitmap is used also if the MAC doesn't support an EEE mode.
So the mode isn't necessarily broken in the PHY. Therefore rename
the bitmap.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/6cd11422-dd67-4c87-a642-308de694af92@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We have some leftovers from the switch to linkmode bitmaps which
- have never been used
- are not used any longer
- have no user outside phy_device.c
So remove them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/5493b96e-88bb-4230-a911-322659ec5167@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce support for standardized PHY statistics reporting in ethtool
by extending the PHYLIB framework. Add the functions
phy_ethtool_get_phy_stats() and phy_ethtool_get_link_ext_stats() to
provide a consistent interface for retrieving PHY-level and
link-specific statistics. These functions are used within the ethtool
implementation to avoid direct access to the phy_device structure
outside of the PHYLIB framework.
A new structure, ethtool_phy_stats, is introduced to standardize PHY
statistics such as packet counts, byte counts, and error counters.
Drivers are updated to include callbacks for retrieving PHY and
link-specific statistics, ensuring values are explicitly set only for
supported fields, initialized with ETHTOOL_STAT_NOT_SET to avoid
ambiguity.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
genphy_c45_write_eee_adv() becomes a no-op if phydev->supported_eee
is cleared. That's not what we want because this function is still
needed to clear the EEE advertisement register(s).
Fill phydev->eee_broken_modes instead to ensure that userspace
can't re-enable EEE advertising.
Fixes: b55498ff14bd ("net: phy: add phy_disable_eee")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/57e2ae5f-4319-413c-b5c4-ebc8d049bc23@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If a MAC driver doesn't support EEE, then the PHY shouldn't advertise it.
Add phy_disable_eee() for this purpose.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/fd51738c-dcd6-4d61-b8c5-faa6ac0f1026@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce the description of a hwtstamp provider, mainly defined with a
the hwtstamp source and the phydev pointer.
Add a hwtstamp provider description within the netdev structure to
allow saving the hwtstamp we want to use. This prepares for future
support of an ethtool netlink command to select the desired hwtstamp
provider. By default, the old API that does not support hwtstamp
selectability is used, meaning the hwtstamp provider pointer is unset.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge in late fixes to prepare for the 6.13 net-next PR.
Conflicts:
include/linux/phy.h
41ffcd95015f net: phy: fix phylib's dual eee_enabled
721aa69e708b net: phy: convert eee_broken_modes to a linkmode bitmap
https://lore.kernel.org/all/20241118135512.1039208b@canb.auug.org.au/
drivers/net/ethernet/wangxun/txgbe/txgbe_phy.c
2160428bcb20 net: txgbe: fix null pointer to pcs
2160428bcb20 net: txgbe: remove GPIO interrupt controller
Adjacent commits:
include/linux/phy.h
41ffcd95015f net: phy: fix phylib's dual eee_enabled
516a5f11eb97 net: phy: respect cached advertising when re-enabling EEE
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
phylib has two eee_enabled members. Some parts of the code are using
phydev->eee_enabled, other parts are using phydev->eee_cfg.eee_enabled.
This leads to incorrect behaviour as their state goes out of sync.
ethtool --show-eee shows incorrect information, and --set-eee sometimes
doesn't take effect.
Fix this by only having one eee_enabled member - that in eee_cfg.
Fixes: 49168d1980e2 ("net: phy: Add phy_support_eee() indicating MAC support EEE")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/E1tBXAF-00341F-EQ@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
bcm_config_lre_aneg() doesn't use genphy_config_eee_advert() any longer.
As this was the only user, we can remove genphy_config_eee_advert() now.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/37da7f3e-b883-4c07-9881-b8c0516822b7@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In addition to 'active-low' and 'inactive-high-impedance' also
support 'active-high' property for PHY LED pin configuration.
As only either 'active-high' or 'active-low' can be set at the
same time, WARN and return an error in case both are set.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/91598487773d768f254d5faf06cf65b13e972f0e.1728558223.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Cross-merge networking fixes after downstream PR (net-6.12-rc3).
No conflicts and no adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Validate PHY LED OPs presence before registering and parsing them.
Defining LED nodes for a PHY driver that actually doesn't supports them
is redundant and useless.
It's also the case with Generic PHY driver used and a DT having LEDs
node for the specific PHY.
Skip it and report the error with debug print enabled.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241008194718.9682-1-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Introduce support for configuring the master/slave role of PHYs based on
the `timing-role` property in the device tree. While this functionality
is necessary for Single Pair Ethernet (SPE) PHYs (1000/100/10Base-T1)
where hardware strap pins may be unavailable or incorrectly set, it
works for any PHY type.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Divya Koppera <divya.koppera@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit c938ab4da0eb ("net: phy: Manual remove LEDs to ensure correct
ordering") correctly fixed a problem with using devm_ but missed
removing the LED entry from the LEDs list.
This cause kernel panic on specific scenario where the port for the PHY
is torn down and up and the kmod for the PHY is removed.
On setting the port down the first time, the assosiacted LEDs are
correctly unregistered. The associated kmod for the PHY is now removed.
The kmod is now added again and the port is now put up, the associated LED
are registered again.
On putting the port down again for the second time after these step, the
LED list now have 4 elements. With the first 2 already unregistered
previously and the 2 new one registered again.
This cause a kernel panic as the first 2 element should have been
removed.
Fix this by correctly removing the element when LED is unregistered.
Reported-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Cc: stable@vger.kernel.org
Fixes: c938ab4da0eb ("net: phy: Manual remove LEDs to ensure correct ordering")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241004182759.14032-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/phy/phy_device.c
2560db6ede1a ("net: phy: Fix missing of_node_put() for leds")
1dce520abd46 ("net: phy: Use for_each_available_child_of_node_scoped()")
https://lore.kernel.org/20240904115823.74333648@canb.auug.org.au
Adjacent changes:
drivers/net/ethernet/xilinx/xilinx_axienet.h
drivers/net/ethernet/xilinx/xilinx_axienet_main.c
858430db28a5 ("net: xilinx: axienet: Fix race in axienet_stop")
76abb5d675c4 ("net: xilinx: axienet: Add statistics support")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Avoid need to manually handle of_node_put() by using
for_each_available_child_of_node_scoped(), which can simplfy code.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The call of of_get_child_by_name() will cause refcount incremented
for leds, if it succeeds, it should call of_node_put() to decrease
it, fix it.
Fixes: 01e5b728e9e4 ("net: phy: Add a binding for PHY LEDs")
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240830022025.610844-1-ruanjinjie@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There are a few PHY drivers that can handle SFP modules through their
sfp_upstream_ops. Introduce Phylib helpers to keep track of connected
SFP PHYs in a netdevice's namespace, by adding the SFP PHY to the
upstream PHY's netdev's namespace.
By doing so, these SFP PHYs can be enumerated and exposed to users,
which will be able to use their capabilities.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Link topologies containing multiple network PHYs attached to the same
net_device can be found when using a PHY as a media converter for use
with an SFP connector, on which an SFP transceiver containing a PHY can
be used.
With the current model, the transceiver's PHY can't be used for
operations such as cable testing, timestamping, macsec offload, etc.
The reason being that most of the logic for these configuration, coming
from either ethtool netlink or ioctls tend to use netdev->phydev, which
in multi-phy systems will reference the PHY closest to the MAC.
Introduce a numbering scheme allowing to enumerate PHY devices that
belong to any netdev, which can in turn allow userspace to take more
precise decisions with regard to each PHY's configuration.
The numbering is maintained per-netdev, in a phy_device_list.
The numbering works similarly to a netdevice's ifindex, with
identifiers that are only recycled once INT_MAX has been reached.
This prevents races that could occur between PHY listing and SFP
transceiver removal/insertion.
The identifiers are assigned at phy_attach time, as the numbering
depends on the netdevice the phy is attached to. The PHY index can be
re-used for PHYs that are persistent.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have an increasing number of drivers that are forcing
auto-negotiation to be enabled for speeds of 1G or faster.
It would appear that auto-negotiation is mandatory for speeds above
100M. In 802.3, Annex 40C's state diagrams seems to imply that
mr_autoneg_enable (BMCR AN ENABLE) doesn't affect whether or not the
AN state machines work for 1000base-T, and some PHY datasheets (e.g.
Marvell Alaska) state that disabling mr_autoneg_enable leaves AN
enabled but forced to 1G full duplex.
Other PHY datasheets imply that BMCR AN ENABLE should not be cleared
for >= 1G.
Thus, this should be handled in phylib rather than in each driver.
Rather than erroring out, arrange to implement the Marvell Alaska
solution but in software for all PHYs: generate an appropriate
single-speed advertisement for the requested speed, and keep AN
enabled to the PHY driver. However, to avoid userspace API breakage,
continue to report to userspace that we have AN disabled.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the PHY of the mido bus is enabled with Wake-on-LAN (WOL),
we cannot suspend the PHY. Although the WOL status has been
checked in phy_suspend(), returning -EBUSY(-16) would cause
the Power Management (PM) to fail to suspend. Since
phy_suspend() is an exported symbol (EXPORT_SYMBOL),
timely error reporting is needed. Therefore, an additional
check is performed here. If the PHY of the mido bus is enabled
with WOL, we skip calling phy_suspend() to avoid PM failure.
From the following logs, it has been observed that the phydev->attached_dev
is NULL, phydev is "stmmac-0:01", it not attached, but it will affect suspend
and resume.The actually attached "stmmac-0:00" will not dpm_run_callback():
mdio_bus_phy_suspend().
init log:
[ 5.932502] YT8521 Gigabit Ethernet stmmac-0:00: attached PHY driver
(mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[ 5.932512] YT8521 Gigabit Ethernet stmmac-0:01: attached PHY driver
(mii_bus:phy_addr=stmmac-0:01, irq=POLL)
[ 24.566289] YT8521 Gigabit Ethernet stmmac-0:00: yt8521_read_status,
link down, media: UTP
suspend log:
[ 322.631362] OOM killer disabled.
[ 322.631364] Freezing remaining freezable tasks
[ 322.632536] Freezing remaining freezable tasks completed (elapsed 0.001 seconds)
[ 322.632540] printk: Suspending console(s) (use no_console_suspend to debug)
[ 322.633052] YT8521 Gigabit Ethernet stmmac-0:01:
PM: dpm_run_callback(): mdio_bus_phy_suspend+0x0/0x110 [libphy] returns -16
[ 322.633071] YT8521 Gigabit Ethernet stmmac-0:01:
PM: failed to suspend: error -16
[ 322.669699] PM: Some devices failed to suspend, or early wake event detected
[ 322.669949] OOM killer enabled.
[ 322.669951] Restarting tasks ... done.
[ 322.671008] random: crng reseeded on system resumption
[ 322.671014] PM: suspend exit
Add a function that phylib can inquire of the driver whether WoL
has been enabled at the PHY.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Youwan Wang <youwan@nfschina.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://patch.msgid.link/20240731091537.771391-1-youwan@nfschina.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core changes for 6.11-rc1.
Lots of stuff in here, with not a huge diffstat, but apis are evolving
which required lots of files to be touched. Highlights of the changes
in here are:
- platform remove callback api final fixups (Uwe took many releases
to get here, finally!)
- Rust bindings for basic firmware apis and initial driver-core
interactions.
It's not all that useful for a "write a whole driver in rust" type
of thing, but the firmware bindings do help out the phy rust
drivers, and the driver core bindings give a solid base on which
others can start their work.
There is still a long way to go here before we have a multitude of
rust drivers being added, but it's a great first step.
- driver core const api changes.
This reached across all bus types, and there are some fix-ups for
some not-common bus types that linux-next and 0-day testing shook
out.
This work is being done to help make the rust bindings more safe,
as well as the C code, moving toward the end-goal of allowing us to
put driver structures into read-only memory. We aren't there yet,
but are getting closer.
- minor devres cleanups and fixes found by code inspection
- arch_topology minor changes
- other minor driver core cleanups
All of these have been in linux-next for a very long time with no
reported problems"
* tag 'driver-core-6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (55 commits)
ARM: sa1100: make match function take a const pointer
sysfs/cpu: Make crash_hotplug attribute world-readable
dio: Have dio_bus_match() callback take a const *
zorro: make match function take a const pointer
driver core: module: make module_[add|remove]_driver take a const *
driver core: make driver_find_device() take a const *
driver core: make driver_[create|remove]_file take a const *
firmware_loader: fix soundness issue in `request_internal`
firmware_loader: annotate doctests as `no_run`
devres: Correct code style for functions that return a pointer type
devres: Initialize an uninitialized struct member
devres: Fix memory leakage caused by driver API devm_free_percpu()
devres: Fix devm_krealloc() wasting memory
driver core: platform: Switch to use kmemdup_array()
driver core: have match() callback in struct bus_type take a const *
MAINTAINERS: add Rust device abstractions to DRIVER CORE
device: rust: improve safety comments
MAINTAINERS: add Danilo as FIRMWARE LOADER maintainer
MAINTAINERS: add Rust FW abstractions to FIRMWARE LOADER
firmware: rust: improve safety comments
...
|
|
In the match() callback, the struct device_driver * should not be
changed, so change the function callback to be a const *. This is one
step of many towards making the driver core safe to have struct
device_driver in read-only memory.
Because the match() callback is in all busses, all busses are modified
to handle this properly. This does entail switching some container_of()
calls to container_of_const() to properly handle the constant *.
For some busses, like PCI and USB and HV, the const * is cast away in
the match callback as those busses do want to modify those structures at
this point in time (they have a local lock in the driver structure.)
That will have to be changed in the future if they wish to have their
struct device * in read-only-memory.
Cc: Rafael J. Wysocki <rafael@kernel.org>
Reviewed-by: Alex Elder <elder@kernel.org>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/2024070136-wrongdoer-busily-01e8@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
phy_suspend() checks the WoL status, and then dereferences
phydrv->flags if (and only if) we decided that WoL has been enabled
on either the PHY or the netdev.
We then check whether phydrv was NULL, but we've potentially already
dereferenced the pointer.
If phydrv is NULL, then phy_ethtool_get_wol() will return an error
and leave wol.wolopts set to zero. However, if netdev->wol_enabled
is true, then we would dereference a NULL pointer.
Checking the PHY drivers, the only place that phydev->wol_enabled is
checked by them is in their suspend/resume callbacks and nowhere else
(which is correct, because phylib only updates this in phy_suspend()).
So, move the NULL pointer check earlier to avoid a NULL pointer
dereference. Leave the check for phydrv->suspend in place as a driver
may populate the .resume method but not the .suspend method.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/E1sN8tn-00GDCZ-Jj@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
net_dev->ethtool is a pointer to new struct ethtool_netdev_state, which
currently contains only the wol_enabled field.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/293a562278371de7534ed1eb17531838ca090633.1719502239.git.ecree.xilinx@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
read_poll_timeout inside phy_read_poll_timeout can set val negative
in some cases (for example, __mdiobus_read inside phy_read can return
-EOPNOTSUPP).
Supposedly, commit 4ec732951702 ("net: phylib: fix phy_read*_poll_timeout()")
should fix problems with wrong-signed vals, but I do not see how
as val is sent to phy_read as is and __val = phy_read (not val)
is checked for sign.
Change val type for signed to allow better error handling as done in other
phy_read_poll_timeout callers. This will not fix any error handling
by itself, but allows, for example, to modify cond with appropriate
sign check or check resulting val separately.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 014068dcb5b1 ("net: phy: genphy_loopback: add link speed configuration")
Signed-off-by: Nikita Kiryushin <kiryushin@ancud.ru>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20240315175052.8049-1-kiryushin@ancud.ru
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Merge in late fixes to prepare for the 6.9 net-next PR.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The phy_get_internal_delay function could try to access to an empty
array in the case that the driver is calling phy_get_internal_delay
without defining delay_values and rx-internal-delay-ps or
tx-internal-delay-ps is defined to 0 in the device-tree.
This will lead to "unable to handle kernel NULL pointer dereference at
virtual address 0". To avoid this kernel oops, the test should be delay
>= 0. As there is already delay < 0 test just before, the test could
only be size == 0.
Fixes: 92252eec913b ("net: phy: Add a helper to return the index for of the internal delay")
Co-developed-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Signed-off-by: Kévin L'hôpital <kevin.lhopital@savoirfairelinux.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order for EEE to operate, both the MAC and the PHY need to support
it, similar to how pause works. With some exception - a number of PHYs
have SmartEEE or AutoGrEEEn support in order to provide some EEE-like
power savings with non-EEE capable MACs.
Copy the pause concept and add the call phy_support_eee() which the MAC
makes after connecting the PHY to indicate it supports EEE. phylib will
then advertise EEE when auto-neg is performed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240302195306.3207716-6-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|