summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath/ath12k/hw.c
AgeCommit message (Collapse)Author
2025-05-16wifi: ath12k: enable monitor mode for WCN7850Kang Yang
Enable monitor mode for WCN7850. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250421023444.1778-14-kang.yang@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-05-16wifi: ath12k: add interrupt configuration for mon status ringKang Yang
The monitor mode design is: 1. Hardware captures packets on the air. 2. Hardware stores the packets into related rings. 3. When the ring buffer reaches the interrupt threshold, it triggers the interrupt. 4. Reap and process the ring buffer in ath12k_dp_service_srng(). Here the interrupt thresholds are intr_timer_thres_us, low_threshold and intr_batch_cntr_thres_entries. An interrupt will be triggered once: 1. Number of packets in the ring reaches intr_batch_cntr_thres_entries. 2. Number of packets in the ring reaches low_threshold(by timer). 3. Timer reaches intr_timer_thres_us. So, add interrupt configuration for the mon status ring, then start to process ring buffers when the interrupt arrives. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250421023444.1778-6-kang.yang@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-04-15wifi: ath12k: don't skip non-primary links for WCN7850Baochen Qiang
The primary link check bypasses REO queue setup for non-primary links in ath12k_dp_rx_peer_tid_setup(), this works for QCN9274 but breaks WCN7850 as WCN7850 needs it to be done for each link peer. Add a new hardware parameter to differentiate them. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Link: https://patch.msgid.link/20250409-ath12k-wcn7850-mlo-support-v2-8-3801132ca2c3@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-04-03wifi: ath12k: Enable REO queue lookup table feature on QCN9274Nithyanantham Paramasivam
Enable the REO queue lookup table feature for QCN9274 by setting the reoq_lut_support flag. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Signed-off-by: Nithyanantham Paramasivam <quic_nithp@quicinc.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250402152529.1649402-4-quic_nithp@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-04-03wifi: ath12k: Fix the enabling of REO queue lookup table featureSriram R
Instead of storing the REO queue address inside peer entries, REO hardware module prefers them to be stored in SRAM which could be directly accessed by REO using peer_ID/TID based lookup table mechanism. Fix the enabling of the REO queue lookup table(LUT) feature by configuring the LUT address information in the REO hardware register and setting the host service flags. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Signed-off-by: Sriram R <quic_srirrama@quicinc.com> Signed-off-by: Nithyanantham Paramasivam <quic_nithp@quicinc.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250402152529.1649402-2-quic_nithp@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-04-02wifi: ath12k: use correct WMI command to set country code for WCN7850Wen Gong
When userspace tries to set country code by NL80211_REGDOM_SET_BY_USER hint(like iw reg set XX), it will pass new country code to ath12k. Then ath12k will set this new country code to firmware by WMI_SET_INIT_COUNTRY_CMDID. For AP based chips(QCN92xx), WMI_SET_INIT_COUNTRY_CMDID is the correct command. However, for STATION based chips(WCN7850), it need to use WMI_SET_CURRENT_COUNTRY_CMDID. Add flag current_cc_support in hardware parameters. It is used to distinguish AP/STA platform. After that, the firmware will work normally and the regulatory feature works well for WCN7850. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Wen Gong <quic_wgong@quicinc.com> Signed-off-by: Kang Yang <quic_kangyang@quicinc.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250401020840.357-3-quic_kangyang@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-03-27wifi: ath12k: add monitor interface support on QCN9274P Praneesh
Currently, the monitor interface is not supported. To support the monitor interface, configure the monitor vdev state identifier, configure the HTT filter setup, subscribe the mac80211 NO_VIRTUAL_MONITOR feature, remove the VIRTUAL_MONITOR handler procedures since align to NO_VIRTUAL_MONITOR feature and prevent monitor interface to transmit packet. Therefore, add these procedures to add monitor interface support and enable the monitor interface support on the QCN9274 platform through the hardware parameter. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250324062518.2752822-11-quic_periyasa@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-03-25wifi: ath12k: add support for fixed QMI firmware memoryRaj Kumar Bhagat
IPQ5332 firmware supports only fixed QMI firmware memory. Hence, add support to read reserved fixed memory region from device-tree and provide the reserved memory segments for firmware to use during QMI firmware memory request. Note that the ability to set the fixed memory will be introduced in a subsequent patch. Currently, the flag remains unset by default, ensuring that existing chipsets are unaffected. Tested-on: IPQ5332 hw1.0 AHB WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00210-QCAHKSWPL_SILICONZ-1 Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> Link: https://patch.msgid.link/20250321-ath12k-ahb-v12-7-bb389ed76ae5@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-03-25wifi: ath12k: Add hw_params to remap CE register space for IPQ5332Balamurugan S
For IPQ5332 CE register space is moved out of WCSS region and the space is not contiguous. Hence, add hardware params (ce_ie_addr & ce_remap) for IPQ5332. These parameters would be used by Ath12k AHB driver (in subsequent patches) to remap the CE registers to a new space for accessing them. Tested-on: IPQ5332 hw1.0 AHB WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00210-QCAHKSWPL_SILICONZ-1 Signed-off-by: Balamurugan S <quic_bselvara@quicinc.com> Co-developed-by: P Praneesh <quic_ppranees@quicinc.com> Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> Link: https://patch.msgid.link/20250321-ath12k-ahb-v12-6-bb389ed76ae5@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-03-25wifi: ath12k: avoid m3 firmware download in AHB device IPQ5332Balamurugan S
Current ath12k devices, QCN9274 and WCN7850, supports m3.bin firmware download through ath12k driver. The new ath12k AHB based device IPQ5332 supports m3 firmware download through remoteproc driver. Hence, add new parameter (fw.m3_loader) in ath12k_hw_params to avoid m3 firmware download in IPQ5332. Tested-on: IPQ5332 hw1.0 AHB WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00210-QCAHKSWPL_SILICONZ-1 Signed-off-by: Balamurugan S <quic_bselvara@quicinc.com> Co-developed-by: P Praneesh <quic_ppranees@quicinc.com> Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> Link: https://patch.msgid.link/20250321-ath12k-ahb-v12-5-bb389ed76ae5@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-03-25wifi: ath12k: add ath12k_hw_params for IPQ5332Balamurugan S
Add ath12k_hw_params for new ath12k AHB based WiFi device IPQ5332. Some hardware parameters like hw_ops, wmi_init & hal_ops are same between IPQ5332 and QCN9274, hence use these same parameters for IPQ5332. Tested-on: IPQ5332 hw1.0 AHB WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00210-QCAHKSWPL_SILICONZ-1 Signed-off-by: Balamurugan S <quic_bselvara@quicinc.com> Co-developed-by: P Praneesh <quic_ppranees@quicinc.com> Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> Link: https://patch.msgid.link/20250321-ath12k-ahb-v12-4-bb389ed76ae5@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-03-25wifi: ath12k: refactor ath12k_hw_regs structureP Praneesh
IPQ5332 device have different register address values for the below registers: HAL_TCL1_RING_BASE_LSB HAL_TCL1_RING_BASE_MSB HAL_TCL2_RING_BASE_LSB HAL_SEQ_WCSS_UMAC_CE0_SRC_REG HAL_SEQ_WCSS_UMAC_CE0_DST_REG HAL_SEQ_WCSS_UMAC_CE1_SRC_REG HAL_SEQ_WCSS_UMAC_CE1_DST_REG Hence, refactor ath12k_hw_regs structure to accommodate these changes in IPQ5332. Tested-on: IPQ5332 hw1.0 AHB WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00210-QCAHKSWPL_SILICONZ-1 Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Co-developed-by: Balamurugan S <quic_bselvara@quicinc.com> Signed-off-by: Balamurugan S <quic_bselvara@quicinc.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> Link: https://patch.msgid.link/20250321-ath12k-ahb-v12-3-bb389ed76ae5@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-26wifi: ath12k: Enable monitor ring mask for QCN9274P Praneesh
QCN9274's monitor related rings are initialized properly. Hence enabling the corresponding ring mask in the hardware params. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Link: https://patch.msgid.link/20241223060132.3506372-15-quic_ppranees@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-26wifi: ath12k: Add HTT source ring ID for monitor ringsP Praneesh
Add source buffer ring and destination buffer ring ID for monitor rings. These IDs are used for ring configuration during initial ring setup. Since monitor rings are enabled based on the rxdma1_enable flag, enable it in the hardware param for the QCN9274 version 2 hardware and increase the destination ring size to handle MSDU data buffers. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Link: https://patch.msgid.link/20241223060132.3506372-2-quic_ppranees@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2024-10-16wifi: ath12k: Add firmware coredump collection supportSowmiya Sree Elavalagan
In case of firmware assert snapshot of firmware memory is essential for debugging. Add firmware coredump collection support for PCI bus. Collect RDDM and firmware paging dumps from MHI and pack them in TLV format and also pack various memory shared during QMI phase in separate TLVs. Add necessary header and share the dumps to user space using dev coredump framework. Coredump collection is disabled by default and can be enabled using menuconfig. Dump collected for a radio is 55 MB approximately. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.2.1-00201-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Link: https://patch.msgid.link/20240717085604.4131642-1-quic_ssreeela@quicinc.com Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
2024-09-04Merge tag 'wireless-next-2024-09-04' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next Kalle Valo says: ==================== pull-request: wireless-next-2024-09-04 here's a pull request to net-next tree, more info below. Please let me know if there are any problems. ==================== Conflicts: drivers/net/wireless/ath/ath12k/hw.c 38055789d151 ("wifi: ath12k: use 128 bytes aligned iova in transmit path for WCN7850") 8be12629b428 ("wifi: ath12k: restore ASPM for supported hardwares only") https://lore.kernel.org/87msldyj97.fsf@kernel.org Link: https://patch.msgid.link/20240904153205.64C11C4CEC2@smtp.kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2024-08-07wifi: ath12k: restore ASPM for supported hardwares onlyAditya Kumar Singh
During PCI based hardware device start up, ASPM is disabled for all. And once firmware is ready, it is restored back. However, not all hardwares (for example QCN9274) supports ASPM. Hence there is a need to conditionally restore ASPM back. Or else, for such hardwares, issue can be seen during sending and receiving packets. Introduce a new hardware param supports_aspm which identifies whether a given hardware supports ASPM or not and then accordingly restore it. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://patch.msgid.link/20240709055817.3371406-1-quic_adisi@quicinc.com
2024-08-05wifi: ath12k: use 128 bytes aligned iova in transmit path for WCN7850Baochen Qiang
In transmit path, it is likely that the iova is not aligned to PCIe TLP max payload size, which is 128 for WCN7850. Normally in such cases hardware is expected to split the packet into several parts in a manner such that they, other than the first one, have aligned iova. However due to hardware limitations, WCN7850 does not behave like that properly with some specific unaligned iova in transmit path. This easily results in target hang in a KPI transmit test: packet send/receive failure, WMI command send timeout etc. Also fatal error seen in PCIe level: ... Capabilities: ... ... DevSta: ... FatalErr+ ... ... ... Work around this by manually moving/reallocating payload buffer such that we can map it to a 128 bytes aligned iova. The moving requires sufficient head room or tail room in skb: for the former we can do ourselves a favor by asking some extra bytes when registering with mac80211, while for the latter we can do nothing. Moving/reallocating buffer consumes additional CPU cycles, but the good news is that an aligned iova increases PCIe efficiency. In my tests on some X86 platforms the KPI results are almost consistent. Since this is seen only with WCN7850, add a new hardware parameter to differentiate from others. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Cc: <stable@vger.kernel.org> Tested-by: Mark Pearson <mpearson-lenovo@squebb.ca> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://patch.msgid.link/20240715023814.20242-1-quic_bqiang@quicinc.com
2024-05-25wifi: ath12k: fix invalid memory access while processing fragmented packetsP Praneesh
The monitor ring and the reo reinject ring share the same ring mask index. When the driver receives an interrupt for the reo reinject ring, the monitor ring is also processed, leading to invalid memory access. Since monitor support is not yet enabled in ath12k, the ring mask for the monitor ring should be removed. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00209-QCAHKSWPL_SILICONZ-1 Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices") Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240520070045.631029-3-quic_ppranees@quicinc.com
2024-05-20wifi: ath12k: dynamic VLAN supportMuna Sinada
Add support for dynamic VLAN. VLAN group traffic is encapsulated and encrypted in mac80211 and driver needs to set flags for the VLAN group traffic to skip hardware encapsulation and encryption. VLAN group traffic utilizes ext MSDU and HTT Metadata to set encapsulation type to RAW and encryption type to OPEN in order to inform firmware to skip hardware encapsulation and encryption. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Muna Sinada <quic_msinada@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240515192830.995013-1-quic_msinada@quicinc.com
2024-05-16wifi: ath12k: Fix tx completion ring (WBM2SW) setup failureNithyanantham Paramasivam
We observe intermittent ping failures from the access point (AP) to station (STA) in any mode (AP-STA or Mesh) configured. Specifically, the transmission completion status is not received at tx completion ring id 4 (WBM2SW ring4) for the packets transmitted via TCL DATA ring id 3. This prevents freeing up tx descriptors and leads to buffer exhaustion. Currently, during initialization of the WBM2SW ring, we are directly mapping the ring number to the ring mask to obtain the ring mask group index. This approach is causing setup failures for WBM2SW ring 4. Similarly, during runtime, when receiving incoming transmission completion status, the validation of the ring number by mapping the interrupted ring mask. This is resulting in validation failure. Thereby preventing entry into the completion handler ath12k_dp_tx_completion_handler(). The existing design assumed that the ring numbers would always be sequential and could be directly mapped with the ring mask. However, this assumption does not hold true for WBM2SW ring 4. Therefore, modify the design such that, instead of mapping the ring number, the ring ID is mapped with the ring mask. According to this design: 1. During initialization of the WBM2SW ring, mapping the ring ID to the ring mask will ensure obtaining the correct ring mask group ID. 2. During runtime, validating the interrupted ring mask group ID within the transmission completion group is sufficient. This approach allows the ring ID to be derived from the interrupted ring mask and enables entry into the completion handler. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices") Signed-off-by: Nithyanantham Paramasivam <quic_nithp@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240510070427.206152-1-quic_nithp@quicinc.com
2024-05-16wifi: ath12k: support SMPS configuration for 6 GHzPradeep Kumar Chitrapu
Parse SMPS configuration from IEs and configure. Without this, SMPS is not enabled for 6 GHz band. This is disabled for WCN7850 as hardware does not support it. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240508173655.22191-7-quic_pradeepc@quicinc.com
2024-05-13wifi: ath12k: fix misspelling of "dma" in num_rxmda_per_pdevJeff Johnson
The ath12k_hw_params member num_rxmda_per_pdev contains a misspelling of "dma" so fix it. No functional changes, compile tested only. Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240504-ath12k_dp_rxdma_ring_sel_config_wcn7850-ret-v1-1-44d2843a2857@quicinc.com
2024-04-23wifi: ath12k: ACPI TAS supportLingbo Kong
Currently, ath12k does not support Time-Average-SAR (TAS). In order to enable TAS read the tables from ACPI and send them to the firmware using WMI_PDEV_SET_BIOS_INTERFACE_CMDID command. Besides, ath12k registers an ACPI event callback so that ACPI can notify ath12k to get the updated SAR power table and sends it to the firmware when the device state is changed. ACPI is only enabled for WCN7850 using struct ath12k_hw_params::acpi_guid field. Most likely QCN9274 will never support ACPI as the chip is not used in laptops. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240422033054.979-2-quic_lingbok@quicinc.com
2024-04-23wifi: ath12k: change supports_suspend to true for WCN7850Baochen Qiang
Now that all things are ready, enable supports_suspend to make suspend/resume work for WCN7850. Don't touch other chips because they don't support suspend. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240412060620.27519-11-quic_bqiang@quicinc.com
2024-02-07wifi: ath12k: advertise P2P dev support for WCN7850Kang Yang
Now that all the necessary pieces are implemented we can enable P2P support for WCN7850. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Kang Yang <quic_kangyang@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240130040303.370590-12-quic_kangyang@quicinc.com
2024-02-05wifi: ath12k: enable 802.11 power save mode in station modeBaochen Qiang
To reduce power consumption enable 802.11 power save mode in station mode. This allows both radio and CPU to sleep more. Only enable the mode on WCN7850, other chips don't support it for now. To test that power save mode is running, run below command and check there is no NULL Data frame seen by a sniffer: iw dev <inf> set power_save off And run below command, then check there is a NULL Data frame in sniffer: iw dev <inf> set power_save on Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240201035830.2534-1-quic_bqiang@quicinc.com
2024-02-02wifi: ath12k: Read board id to support split-PHY QCN9274Ganesh Babu Jothiram
QCN9274 can support single-PHY or split-PHY architecture. Currently, only the single-PHY architecture is supported in ath12k. The split-PHY QCN9274 requires different AMSS firmware binary "amss_dualmac.bin". Hence, add support to read board id from OTP. Based on board id decide whether single-mac / dual-mac firmware needs to be downloaded to the target. Also, update HW param max_radios to support split-PHY in QCN9274. Also, add new Firmware IE for firmware_N.bin "ATH11K_FW_IE_AMSS_DUALMAC_IMAGE" to support dualmac QCN9274. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Ganesh Babu Jothiram <quic_gjothira@quicinc.com> Co-developed-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240129065724.2310207-13-quic_rajkbhag@quicinc.com
2024-02-02wifi: ath12k: remove hal_desc_sz from hw paramsRaj Kumar Bhagat
With word mask subscription support, the rx_desc structure will change. The fields in this structure rx_desc will be reduced to only the required fields. To make word mask subscription changes compatible with the older firmware version (firmware that does not support word mask subscription), two different structures of rx_desc will be required for the same hardware. The hardware param hal_desc_sz value cannot be constant for the same hardware. It depends on the size of rx_desc structure which may change based on firmware capability to support word mask subscription. Hence, remove hal_desc_sz from hardware param and add hal_rx_ops to get the size of rx_desc in run time. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240129065724.2310207-9-quic_rajkbhag@quicinc.com
2024-01-17wifi: ath12k: refactor QMI MLO host capability helper functionKarthikeyan Periyasamy
Currently, QMI MLO host capability parameters are specific to the WCN7850 platform. To make use of this helper function across all the platforms, move the platform specific MLO capability parameter to the HW param configuration. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://msgid.link/20240113001659.1022465-2-quic_periyasa@quicinc.com
2023-12-05wifi: ath12k: fix and enable AP mode for WCN7850Kang Yang
For AP mode, the peer is created earlier in ath12k_mac_op_add_interface() but ath12k_mac_op_assign_vif_chanctx() will try to create peer again. Then an error will return which makes AP mode startup fail. Kernel log: [ 5017.665006] ath12k_pci 0000:04:00.0: failed to create peer after vdev start delay: -22 wpa_supplicant log: Failed to set beacon parameters Interface initialization failed wls1: interface state UNINITIALIZED->DISABLED wls1: AP-DISABLED wls1: Unable to setup interface. Failed to initialize AP interface wls1: interface state DISABLED->DISABLED wls1: AP-DISABLED So fix this check and enable AP mode for WCN7850, as now AP mode works normally. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by: Kang Yang <quic_kangyang@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20231121022459.17209-1-quic_kangyang@quicinc.com
2023-11-30wifi: ath12k: Update Qualcomm Innovation Center, Inc. copyrightsJeff Johnson
Update the copyright for all ath12k files modified on behalf of Qualcomm Innovation Center, Inc. in 2023. Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20231128-ath12kcopyrights-v1-1-be0b7408cbac@quicinc.com
2023-10-18wifi: ath12k: Enable Mesh support for QCN9274Ramya Gnanasekar
Currently QCN9274 supports only AP and station interface modes. Add interface type mesh to ath12k_hw_params for QCN9274 to provide support for mesh mode as well. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0-02903-QCAHKSWPL_SILICONZ-1 Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20231013070007.25597-2-quic_rgnanase@quicinc.com
2023-10-12wifi: ath12k: configure RDDM size to MHI for device recoveryWen Gong
RDDM is Ram Dump Debug Module which is used to debug issues when the firmware encounters an error. The rddm_size is needed by the firmware while MHI goes to the RDDM state. Provide the size to MHI subsystem so that the firmware restart works when the firmware crashes. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by: Wen Gong <quic_wgong@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230721055305.20420-2-quic_wgong@quicinc.com
2023-09-28wifi: ath12k: add support for hardware rfkill for WCN7850Lingbo Kong
When hardware rfkill is enabled in the firmware, it will report the capability using WMI_SYS_CAP_INFO_RFKILL bit in the WMI_SERVICE_READY event to the host. Currently ath12k does not process this service capability. In order to support this, update ath12k to check if the capability is enabled, if so, send the GPIO information to firmware. When the firmware detects hardware rfkill is enabled by the user, it will report it using WMI_RFKILL_STATE_CHANGE_EVENTID. When ath12k receive the event, it will set the value of rfkill_radio_on based on whether radio_state is equal to WMI_RFKILL_RADIO_STATE_ON, then send WMI_PDEV_PARAM_RFKILL_ENABLE to firmware. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230906110412.182176-1-quic_lingbok@quicinc.com
2023-04-26wifi: ath12k: set PERST pin no pull request for WCN7850Carl Huang
The PCIe PERST pin is currently pulled down on WCN7850 and it causes some power leakage. Fix it by notifying firmware not to pull down PCIe PERST pin in QMI message for WCN7850. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230404032057.3236122-3-quic_cjhuang@quicinc.com
2023-04-26wifi: ath12k: add qmi_cnss_feature_bitmap field to hardware parametersCarl Huang
Currently the CNSS (Connectivity Subsystem) QMI feature is assigned to qmi_wlanfw_host_cap_req_msg_v01 request directly, this prevents chip-specific CNSS features from being added easily. Solve this by adding a new field qmi_cnss_feature_bitmap to hw_params so chip-specific CNSS features can be assigned to this field and later assigned to qmi_wlanfw_host_cap_req_msg_v01 request. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230404032057.3236122-2-quic_cjhuang@quicinc.com
2023-03-22wifi: ath12k: Enable IMPS for WCN7850Baochen Qiang
To reduce power consumption, change idle_ps to true to enable Idle Mode Power Save (IMPS) for WCN7850. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230317062533.18240-1-quic_bqiang@quicinc.com
2022-11-29wifi: ath12k: driver for Qualcomm Wi-Fi 7 devicesKalle Valo
ath12k is a new mac80211 driver for Qualcomm Wi-Fi 7 devices, first supporting QCN9274 and WCN7850 PCI devices. QCN9274 supports both AP and station; WCN7850 supports only station mode. Monitor mode is not (yet) supported. Only PCI bus devices are supported. ath12k is forked from an earlier version of ath11k. It was simpler to have a "clean start" for the new generation and not try to share the code with ath11k. This makes maintenance easier and avoids major changes in ath11k, which would have significantly increased the risk of regressions in existing setups. ath12k uses le32 and cpu_to_le32() macros to handle endian conversions, instead of using the firmware byte swap feature utilized by ath11k. There is only one kernel module, named ath12k.ko. Currently ath12k only supports HE mode (IEEE 802.11ax) or older, but work is ongoing to add EHT mode (IEEE 802.11be) support. The size of the driver is ~41 kLOC and 45 files. To make the review easier, this initial version of ath12k does not support Device Tree, debugfs or any other extra features. Those will be added later, after ath12k is accepted to upstream. The driver is build tested by Intel's kernel test robot with both GCC and Clang. Sparse reports no warnings. The driver is mostly free of checkpatch warnings, albeit few of the warnings are omitted on purpose, list of them here: https://github.com/qca/qca-swiss-army-knife/blob/master/tools/scripts/ath12k/ath12k-check#L52 The driver has had multiple authors who are listed in alphabetical order below. Co-developed-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com> Signed-off-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com> Co-developed-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Co-developed-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com> Signed-off-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com> Co-developed-by: Carl Huang <quic_cjhuang@quicinc.com> Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com> Co-developed-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com> Co-developed-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Co-developed-by: P Praneesh <quic_ppranees@quicinc.com> Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Co-developed-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com> Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com> Co-developed-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com> Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com> Co-developed-by: Sriram R <quic_srirrama@quicinc.com> Signed-off-by: Sriram R <quic_srirrama@quicinc.com> Co-developed-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com> Signed-off-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com> Co-developed-by: Wen Gong <quic_wgong@quicinc.com> Signed-off-by: Wen Gong <quic_wgong@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
generated by cgit (git 2.34.1) at 2025-06-14 16:31:51 +0000