Age | Commit message (Collapse) | Author |
|
Refine the power parameters for better step response especially at high
current ramp case that is caused by power inductor variation.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240103070155.119488-1-pkshih@realtek.com
|
|
A mouse that uses a USB connection is called a "USB mouse" device (or
"USB mouse" for short), not a "mouse USB" device. By analogy, a WiFi
adapter that connects to the host computer via USB is a "USB wireless"
device, not a "wireless USB" device. (The latter term more properly
refers to a defunct Wireless USB specification, which described a
technology for sending USB protocol messages over an ultra wideband
radio link.)
Similarly for a WiFi adapter card that plugs into a PCIe slot: It is a
"PCIe wireless" device, not a "wireless PCIe" device.
Rephrase the text in the kernel source where the word ordering is
wrong.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/57da7c80-0e48-41b5-8427-884a02648f55@rowland.harvard.edu
|
|
The flush period may not always intersect with DTIM and when that
happens, an error log "timed out to flush pci TX ring[6]" is shown.
Bypass this since hardware will do proper transmission on the next
DTIM period for broadcast/multicast packets in high queue.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230616125540.36877-4-pkshih@realtek.com
|
|
Remove pci_clear_master to simplify the code,
the bus-mastering is also cleared in do_pci_disable_device,
like this:
./drivers/pci/pci.c:2197
static void do_pci_disable_device(struct pci_dev *dev)
{
u16 pci_command;
pci_read_config_word(dev, PCI_COMMAND, &pci_command);
if (pci_command & PCI_COMMAND_MASTER) {
pci_command &= ~PCI_COMMAND_MASTER;
pci_write_config_word(dev, PCI_COMMAND, pci_command);
}
pcibios_disable_device(dev);
}.
And dev->is_busmaster is set to 0 in pci_disable_device.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230323112613.7550-4-cai.huoqing@linux.dev
|
|
clang with W=1 reports
drivers/net/wireless/realtek/rtw88/pci.c:92:21: error:
unused function 'rtw_pci_get_tx_desc' [-Werror,-Wunused-function]
static inline void *rtw_pci_get_tx_desc(struct rtw_pci_tx_ring *tx_ring, u8 idx)
^
This function is not used, so remove it.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230320233448.1729899-1-trix@redhat.com
|
|
This code is not specific to the PCIe bus type but can be re-used by USB
and SDIO bus types. Move it to tx.{c,h} to avoid code-duplication in the
future. While here, add checking of the ac argument in
rtw_tx_ac_to_hwq() so we're not accessing entries beyond the end of the
array.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230204233001.1511643-4-martin.blumenstingl@googlemail.com
|
|
This makes it easier to understand which values are allowed for the
"queue" variable when using the enum instead of an u8.
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230204233001.1511643-3-martin.blumenstingl@googlemail.com
|
|
rtw_hw_queue_mapping() and ac_to_hwq[] hold values of type enum
rtw_tx_queue_type. Change their types to reflect this to make it easier
to understand this part of the code.
While here, also change the array to be static const as it is not
supposed to be modified at runtime.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230204233001.1511643-2-martin.blumenstingl@googlemail.com
|
|
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since chip_info has became const table, we must access them via const
pointer to avoid invalid writing.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220727065232.28510-1-pkshih@realtek.com
|
|
Defining local versions of NAPI_POLL_WEIGHT with the same
values in the drivers just makes refactoring harder.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220429174643.196994-2-kuba@kernel.org
|
|
Disable this capability to avoid timeout errors on certain platforms.
Without it, pci bus might stuck and leads to disconnection.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220420093058.31646-2-pkshih@realtek.com
|
|
Make workaround work for other 8821CE devices with different PCI ID
Signed-off-by: Jimmy Hon <honyuenkwun@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220407075123.420696-3-honyuenkwun@gmail.com
|
|
To support stations in power saving mode, AP should notify stations
that there are frames buffered at the AP via TIM during beacons.
Driver used to transmit identical beacons that were downloaded to
hardware during the initiation phase. This beacon will become
obsolete over time.
If the beacon does not contain sufficient information, station would
not be able to percept that there is data to receive. Hence it won't
wake up and start the PS-poll procedure, this could lead to timeout
and/or lost data segments. In order to resolve this issue, driver will
now download beacon to hardware whenever the content is updated.
Enable hardware to update dtim_count for more efficiency, this reduces
the overhead of downloading beacon at every beacon interval since most
of the time only the dtim_count needs to be updated.
Change queue mapping for broadcast/multicast frames to high queue, so
these frames can be prioritized and sent when dtim_count is zero.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220407095858.46807-4-pkshih@realtek.com
|
|
In original flow, driver needs to ensure chip leave deep ps mode
before transmitting any packet, and don't enter deep ps mode beofre
PCIE DMA is finished. Now with the support of 8822ce's hardware
setting and firmware after v9.9.11, these limits are removed.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221020230.20764-1-pkshih@realtek.com
|
|
Many Intel based platforms face system random freeze after commit
9e2fd29864c5 ("rtw88: add napi support").
The commit itself shouldn't be the culprit. My guess is that the 8821CE
only leaves ASPM L1 for a short period when IRQ is raised. Since IRQ is
masked during NAPI polling, the PCIe link stays at L1 and makes RX DMA
extremely slow. Eventually the RX ring becomes messed up:
[ 1133.194697] rtw_8821ce 0000:02:00.0: pci bus timeout, check dma status
Since the 8821CE hardware may fail to leave ASPM L1, manually do it in
the driver to resolve the issue.
Fixes: 9e2fd29864c5 ("rtw88: add napi support")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=215131
BugLink: https://bugs.launchpad.net/bugs/1927808
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Jian-Hong Pan <jhp@endlessos.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211215114635.333767-1-kai.heng.feng@canonical.com
|
|
8821CE causes random freezes on HP 250 G7 Notebook PC. Add a quirk
to disable pci ASPM capability.
Reported-by: rtl8821cerfe2 <rtl8821cerfe2@protonmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211119052437.8671-1-pkshih@realtek.com
|
|
8821CE causes random freezes on HP Pavilion 14-ce0019nf. Add a quirk
to disable pci ASPM capability.
Signed-off-by: Ugo Rémery <ugo.remery@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210822194932.29630-1-Larry.Finger@lwfinger.net
|
|
The rtw_pci_init_rx_ring function is only ever called with a fixed
constant or RTK_MAX_RX_DESC_NUM for the "len" argument. Since this
constant is defined as 512, the "if (len > TRX_BD_IDX_MASK)" check
can never happen (TRX_BD_IDX_MASK is defined as GENMASK(11, 0) or in
other words as 4095).
So, remove this check.
The true motivation for this patch is to silence a false Coverity
warning.
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Len Baker <len.baker@gmx.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210731163546.10753-1-len.baker@gmx.com
|
|
We find the power sequence of system suspend flow don't meet
the criteria when using 8822CE-VR chip by rfe-type 6, because the
reference clock form host is sometimes late. To avoid the behavoir,
we keep CLKREQ# signal to low during suspend to make sure the reference
clock arrival in time.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210727100503.31626-1-pkshih@realtek.com
|
|
8821CE with ASPM cannot work properly on Protempo Ltd L116HTN6SPW. Add a
quirk to disable the cap.
The reporter describes the symptom is that this module (driver) causes
frequent freezes, randomly but usually within a few minutes of running
(thus very soon after boot): screen display remains frozen, no response
to either keyboard or mouse input. All I can do is to hold the power
button to power off, then reboot.
Reported-by: Paul Szabo <psz2036@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210607012254.6306-1-pkshih@realtek.com
|
|
We used to stop napi before disabling irqs. And it turns out
to cause some problem when we try to stop device while interrupt arrives.
To safely stop pci, we do three steps:
1. disable interrupt
2. synchronize_irq
3. stop_napi
Since step 2 and 3 may not finish as expected when interrupt is enabled,
use rtwpci->running to decide whether interrupt should be re-enabled at
the time.
Fixes: 9e2fd29864c5 ("rtw88: add napi support")
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210415084703.27255-4-pkshih@realtek.com
|
|
If there are lots of packets to be transmitted, the driver would check
whether the available descriptors are sufficient according the read/write
point of tx queue. Once the available descriptor is not enough,
ieee80211_stop_queue is called.
TX ISR, meanwhile, is releasing the tx resources after the packets are
transmitted. This routine may call ieee80211_wake_queue by checking the
available descriptor.
The potential queue stop problem would occur when the tx queue is
stopped due to the heavy traffic. Then thare is no chance to wake the
queue up because the read point is not updated immediately, as a result,
no more packets coulde be transmitted in this queue.
This patch makes sure the ieee80211_wake_queue could be called properly
and avoids the race condition when ring->r.rp, ring->queue_stopped are
updated.
Signed-off-by: Yu-Yen Ting <steventing@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210415084703.27255-3-pkshih@realtek.com
|
|
Though mac queue flushing has been supported, sometimes data may be waiting
on interface from host to chip. If it occurs, there may still be data that
flows into mac just after we do flush. To avoid that, we add the hci part
of flushing.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210319054218.3319-2-pkshih@realtek.com
|
|
Use napi to reduce overhead on rx interrupts.
Driver used to interrupt kernel for every Rx packet, this could
affect both system and network performance. NAPI is a mechanism that
uses polling when processing huge amount of traffic, by doing this
the number of interrupts can be decreased.
Network performance can also benefit from this patch. Since TCP
connection is bidirectional and acks are required for every several
packets. These ack packets occupie the PCI bus bandwidth and could
lead to performance degradation.
When napi is used, GRO receive is enabled by default in the mac80211
stack. So mac80211 won't pass every RX TCP packets to the kernel TCP
network stack immediately. Instead an aggregated large length TCP packet
will be delivered.
This reduces the tx acks sent and gains rx performance. After the patch,
the Rx throughput increases about 25Mbps in 11ac.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210209070755.23019-4-pkshih@realtek.com
|
|
There are reports that 8822CE fails to work rtw88 with "failed to read DBI
register" error. Also I have a system with 8723DE which freezes the whole
system when the rtw88 is probing the device.
According to [1], platform firmware may not properly power manage the
device during shutdown. I did some expirements and putting the device to
D3 can workaround the issue.
So let's power cycle the device by putting the device to D3 at shutdown
to prevent the issue from happening.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=206411#c9
BugLink: https://bugs.launchpad.net/bugs/1872984
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200928165508.20775-1-kai.heng.feng@canonical.com
|
|
This handles the situation when firmware crashes.
When firmware crashes, it will send an interrupt, and driver will queue
a work for recovery.
In the work, driver will reset it's internal association state, which
includes removing associated sta's macid, resetting vifs' states
and removing keys. After resetting the driver's state, driver will call
rtw_enter_ips() to force the chipset power off to reset the chip.
Finally, driver calls ieee80211_restart_hw() to inform mac80211 stack
to restart.
Since only 8822c firmware supports this feature, the interrupt will only
be triggered when 8822c chipset is loaded.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200925061219.23754-3-tehuang@realtek.com
|
|
The wrappers in include/linux/pci-dma-compat.h should go away.
The patch has been generated with the coccinelle script below and has been
hand modified to replace GFP_ with a correct flag.
It has been compile tested.
When memory is allocated in 'rtw_pci_init_tx_ring()' and
'rtw_pci_init_rx_ring()' GFP_KERNEL can be used because both functions are
called from a probe function and no spinlock is taken.
The call chain is:
rtw_pci_probe
--> rtw_pci_setup_resource
--> rtw_pci_init
--> rtw_pci_init_trx_ring
--> rtw_pci_init_tx_ring
--> rtw_pci_init_rx_ring
@@
@@
- PCI_DMA_BIDIRECTIONAL
+ DMA_BIDIRECTIONAL
@@
@@
- PCI_DMA_TODEVICE
+ DMA_TO_DEVICE
@@
@@
- PCI_DMA_FROMDEVICE
+ DMA_FROM_DEVICE
@@
@@
- PCI_DMA_NONE
+ DMA_NONE
@@
expression e1, e2, e3;
@@
- pci_alloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3;
@@
- pci_zalloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3, e4;
@@
- pci_free_consistent(e1, e2, e3, e4)
+ dma_free_coherent(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_single(e1, e2, e3, e4)
+ dma_map_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_single(e1, e2, e3, e4)
+ dma_unmap_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4, e5;
@@
- pci_map_page(e1, e2, e3, e4, e5)
+ dma_map_page(&e1->dev, e2, e3, e4, e5)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_page(e1, e2, e3, e4)
+ dma_unmap_page(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_sg(e1, e2, e3, e4)
+ dma_map_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_sg(e1, e2, e3, e4)
+ dma_unmap_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+ dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_device(e1, e2, e3, e4)
+ dma_sync_single_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+ dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+ dma_sync_sg_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2;
@@
- pci_dma_mapping_error(e1, e2)
+ dma_mapping_error(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_dma_mask(e1, e2)
+ dma_set_mask(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_consistent_dma_mask(e1, e2)
+ dma_set_coherent_mask(&e1->dev, e2)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200820150643.148219-1-christophe.jaillet@wanadoo.fr
|
|
Some platforms cannot read the DBI register successfully for the
ASPM settings. After the read failed, the bus could be unstable,
and the device just became unavailable [1]. For those platforms,
the ASPM should be disabled. But as the ASPM can help the driver
to save the power consumption in power save mode, the ASPM is still
needed. So, add a module parameter for them to disable it, then
the device can still work, while others can benefit from the less
power consumption that brings by ASPM enabled.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=206411
[2] Note that my lenovo T430 is the same.
Fixes: 3dff7c6e3749 ("rtw88: allows to enable/disable HCI link PS mechanism")
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200605074703.32726-1-yhchuang@realtek.com
|
|
remove the unused about pci after extracting chip modules
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515052327.31874-7-yhchuang@realtek.com
|
|
Make objects about 8723d functions and 8723d tables,
i.e. rtw8723d.o and rtw8723d_table.o, an individual
kernel module called rtw88_8723d.ko.
For 8723d pcie chip, i.e. 8723DE chip, add a chip
entry point module called rtw88_8723de.ko which
will depend on rtw88_8723d.ko and rtwpci.ko.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515052327.31874-6-yhchuang@realtek.com
|
|
Make objects about 8822b functions and 8822b tables,
i.e. rtw8822b.o and rtw8822b_table.o, an individual
kernel module called rtw88_8822b.ko.
For 8822b pcie chip, i.e. 8822BE chip, add a chip
entry point module called rtw88_8822be.ko which
will depend on rtw88_8822b.ko and rtwpci.ko.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515052327.31874-5-yhchuang@realtek.com
|
|
Make objects about 8822c functions and 8822c tables,
i.e. rtw8822c.o and rtw8822c_table.o, an individual
kernel module called rtw88_8822c.ko.
For 8822c pcie chip, i.e. 8822CE chip, add a chip
entry point module called rtw88_8822ce.ko which
will depend on rtw88_8822c.ko and rtwpci.ko.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515052327.31874-4-yhchuang@realtek.com
|
|
In the current design, chip entry points are built into
the pci module. That makes the pci module depend on chips.
According to dependence, once the pci module is loaded,
kernel will load chip functionalities, including those that
may not be currently used.
We plan to split chip entry points from the pci module.
Thence we export pci symbols that will be used in chip
entry point modules.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200515052327.31874-3-yhchuang@realtek.com
|
|
Without this patch, wifi card can't initialize properly due to BT in USB
suspend state. So, we disable BT USB suspend (wakeup) in shutdown callback
that is the moment before rebooting. To save BT USB power, we can't do this
in 'remove' callback.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200512102621.5148-5-yhchuang@realtek.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.8
First set of patches for v5.8. Changes all over, ath10k apparently
seeing most new features this time. rtw88 also had lots of changes due
to preparation for new hardware support.
In this pull request there's also a new macro to include/linux/iopoll:
read_poll_timeout_atomic(). This is needed by rtw88 for atomic
polling.
Major changes:
ath11k
* add debugfs file for testing ADDBA and DELBA
* add 802.11 encapsulation offload on hardware support
* add htt_peer_stats_reset debugfs file
ath10k
* enable VHT160 and VHT80+80 modes
* enable radar detection in secondary segment
* sdio: disable TX complete indication to improve throughput
* sdio: decrease power consumption
* sdio: add HTT TX bundle support to increase throughput
* sdio: add rx bitrate reporting
ath9k
* improvements to AR9002 calibration logic
carl9170
* remove buggy P2P_GO support
p54usb
* add support for AirVasT USB stick
rtw88
* add support for antenna configuration
ti wlcore
* add support for AES_CMAC cipher
iwlwifi
* support for a few new FW API versions
* new hw configs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
the related system resources were not released when pci_iomap() return
error in the rtw_pci_io_mapping() function. add pci_release_regions() to
fix it.
Fixes: e3037485c68ec1a ("rtw88: new Realtek 802.11ac driver")
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Acked-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504083442.3033-1-zhengdejin5@gmail.com
|
|
H2C queue is used to send command to firmware. Since 8723D doesn't support
this queue, this commit check wlan_cpu flag to avoid to set H2C related
registers.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200422034607.28747-6-yhchuang@realtek.com
|
|
RTL8723DE is an 11n 1x1 2.4G single band chip with the
following capabilities:
- TX/RX BD size: 16/8
- TX/RX desc size: 40/24
- physical/logical/protected efuse size: 512/512/96
- TX gain index factor: 1
- max TX power index: 0x3F
- band: 2G
- HT: support
- VHT: Not support
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200420055054.14592-2-yhchuang@realtek.com
|
|
The rtw88 driver defines emtpy functions with multiple indirections
but gets one of these wrong:
drivers/net/wireless/realtek/rtw88/pci.c:1347:12: error: 'rtw_pci_resume' defined but not used [-Werror=unused-function]
1347 | static int rtw_pci_resume(struct device *dev)
| ^~~~~~~~~~~~~~
drivers/net/wireless/realtek/rtw88/pci.c:1342:12: error: 'rtw_pci_suspend' defined but not used [-Werror=unused-function]
1342 | static int rtw_pci_suspend(struct device *dev)
Better simplify it to rely on the conditional reference in
SIMPLE_DEV_PM_OPS(), and mark the functions as __maybe_unused to avoid
warning about it.
I'm not sure if these are needed at all given that the functions
don't do anything, but they were only recently added.
Fixes: 44bc17f7f5b3 ("rtw88: support wowlan feature for 8822c")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200408185413.218643-1-arnd@arndb.de
|
|
Driver used to kick off every TX packets, that will waste some
time while we can do better to kick off the TX packets once after
they are all prepared to be transmitted.
For PCI, it uses DMA engine to transfer the SKBs to the device,
and the transition of the state of the DMA engine could be a cost.
Driver can save some time to kick off multiple SKBs once so that
the DMA engine will have only one transition.
So, split rtw_hci_ops::tx() to rtw_hci_ops::tx_write() and
rtw_hci_ops::tx_kick_off() to explicitly kick the SKBs off after
they are written to the prepared buffer. For packets come from
ieee80211_ops::tx(), write one and then kick it off immediately.
For packets queued in TX queue, which come from
ieee80211_ops::wake_tx_queue(), we can dequeue them, write them
to the buffer, and then kick them off together.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200312080852.16684-6-yhchuang@realtek.com
|
|
Add a macro TRX_BD_IDX_MASK for access the TX/RX BD indexes.
The hardware has only 12 bits for TX/RX BD indexes, we should not
initialize a TX/RX ring or access the TX/RX BD index with a length
that is larger than TRX_BD_IDX_MASK.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200312080852.16684-5-yhchuang@realtek.com
|
|
Extract skb allocation routines for rsvd_page and h2c.
These routines should also be used by USB and SDIO.
This should not change the logic at all.
memset() for pkt_info is unnecessary, just declare as {0}.
Also skb_put()/memcpy() can be replaced by skb_put_data().
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200312080852.16684-3-yhchuang@realtek.com
|
|
This driver generally only needs to ensure that
(a) it doesn't try to process TX interrupts at the same time as
power-save operations (and similar)
(b) the device interrupt gets disabled while we're still handling the
last set of interrupts
For (a), all the operations (e.g., PS transitions, packet handling)
happens in non-atomic contexts (e.g., threaded IRQ).
For (b), we only need mutual exclusion for brief sections (i.e., while
we're actually manipulating the interrupt mask/status).
So, we can introduce a separate lock for handling (b), disabling IRQs
while we do it. For (a), we can demote the locking to BH only, now that
(b) (the only steps done in atomic context) and that has its own lock.
This helps reduce the amount of time this driver spends with IRQs off.
Notably, transitioning out of power-save modes can take >3 milliseconds,
and this transition is done under the protection of 'irq_lock'.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200312080852.16684-2-yhchuang@realtek.com
|
|
Reduce the data size 2kb or 3kb by making tables const.
Add const to pointer declarations to make compilation work too.
(x86-64 defconfig)
$ size drivers/net/wireless/realtek/rtw88/rtw8822?.o*
text data bss dec hex filename
25054 672 8 25734 6486 drivers/net/wireless/realtek/rtw88/rtw8822b.o.new
23870 1872 8 25750 6496 drivers/net/wireless/realtek/rtw88/rtw8822b.o.old
53646 828 0 54474 d4ca drivers/net/wireless/realtek/rtw88/rtw8822c.o.new
52846 1652 0 54498 d4e2 drivers/net/wireless/realtek/rtw88/rtw8822c.o.old
(x86-64 allyesconfig)
$ size drivers/net/wireless/realtek/rtw88/rtw8822?.o*
text data bss dec hex filename
45811 6280 128 52219 cbfb drivers/net/wireless/realtek/rtw88/rtw8822b.o.new
44211 7880 128 52219 cbfb drivers/net/wireless/realtek/rtw88/rtw8822b.o.old
100195 8128 0 108323 1a723 drivers/net/wireless/realtek/rtw88/rtw8822c.o.new
98947 9376 0 108323 1a723 drivers/net/wireless/realtek/rtw88/rtw8822c.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since RTL8822CE has enabled reference clock auto calibration,
there is no need to add any clock delay for covering the timing
gap of the reference clock.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Sometimes the TX queue may be empty and we could possible
dequeue a NULL pointer, crash the kernel. If the skb is NULL
then there is nothing to do, just leave the ISR.
And the TX queue should not be empty here, so print an error
to see if there is anything wrong for DMA ring.
Fixes: e3037485c68e ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Wake on WLAN(wowlan) is a feature which allows devices
to be woken up from suspend state through wlan events.
When user enables wowlan feature and then let the device
enter suspend state, wowlan firmware will be loaded by
the driver and periodically monitors wifi packets.
Power consumption of wifi chip will be reduced in this
state.
If wowlan firmware detects that specific wlan event
happens, it will issue wakeup signal to trigger resume
process. Driver will load normal firmware and let wifi
chip return to the original state.
Currently supported wlan events include receiving magic packet,
rekey packet and deauth packet, and disconnecting from AP.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Some devices need to configure interface/HCI related reigsters
in power on flow. Add interface_cfg for HCI for the settings.
The driver only supports RTL8822BE/RTL8822CE now, and since
RTL8822BE does not need to configure PCIE, the configuration
is only added for RTL8822CE. Without it, some of the RTL8822CE
device can crash and disconnected to host in suspend/wowlan mode.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When PCI trx rings are reset, the DMA engine should also be reset.
Otherswise, the rx_tag of rx flow is not synchronous to hw.
Remove DMA reset when rtw_pci_start() as we added it in
rtw_pci_setup().
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|