| Age | Commit message (Collapse) | Author |
|---|
|
The comment for this dbg_show says that it is supposed to return more
than what the generic code is showing, including de-glitching. That's
wrong because:
- this chip does not support deglitching,
- the code does not print anything extra compared to the generic
handler,
- its behavior is different because it skips unrequested GPIOs; the
generic code prints their names if they're assigned
There is an important difference, though. Previously, dbg_show would
re-check some registers to see if they still match what the regmap
thinks should be in there. This was semi-useful when develpoing the HW
board because it immediately pointed to SPI wiring problem if a CS
connection was missing (0xffs are easy to see). However, I do not think
that this makes much sense -- and one could always do this in some other
way if needed.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Cc: Phil Reid <preid@electromag.com.au>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fix sparse warnings:
drivers/pinctrl/pinctrl-artpec6.c:691:5: warning:
symbol 'artpec6_pmx_enable' was not declared. Should it be static?
drivers/pinctrl/pinctrl-artpec6.c:705:6: warning:
symbol 'artpec6_pmx_disable' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v5.2
- Add HSCIF (serial) pin groups on R-Car H1,
- Add I2C[035] pin groups on R-Car M3-N,
- Add CANFD pin groups on RZ/G2M and RZ/G2E,
- Retain SDHI/MMC clock return path delay configuration across
suspend/resume on R-Car Gen3,
- More validation of pinmux tables at build and runtime, including
compile-test coverage of all drivers,
- Small fixes, improvements, and cleanups.
|
|
This patch adds I2C{0,3,5} pins, groups and functions to the R8A7796 SoC.
These pins are physically muxed with other pins. Therefore, setup of
MOD_SEL is needed for exclusive control with other pins.
[takeshi.kihara.df: add blank lines after function declarations]
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[uli: use standard macros PINMUX_IPSR_PHYS and PINMUX_IPSR_PHYS_MSEL]
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Pin data for I2C controllers 0, 3 and 5 is properly defined already.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Replace "F_(0,0)" by "F_(0, 0)".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Fix sparse warning:
drivers/pinctrl/freescale/pinctrl-scu.c:38:19: warning:
symbol 'pinctrl_ipc_handle' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Lochnagar is an evaluation and development board for Cirrus
Logic Smart CODEC and Amp devices. It allows the connection of
most Cirrus Logic devices on mini-cards, as well as allowing
connection of various application processor systems to provide a
full evaluation platform. This driver supports the board
controller chip on the Lochnagar board.
Lochnagar provides many pins which can generally be used for an
audio function such as an AIF or a PDM interface, but also as
GPIOs.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Our pinctrl drivers are consisting of some common code, and big pin tables
that are SoC-specific. This is fine in most cases, but when you want to
reduce the size of the particular kernel image, those big tables are, well,
quite big.
We haven't had the option to disable them in the past since they were
hidden Kconfig options based on the SoC support. However, that granularity
isn't great since we don't have one Kconfig option per-SoC, but rather one
by family.
Make those options selectable by the user so that they can disable it if
needed, while keeping the current default to not change the standard case.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Our pin controller can configure the pins no matter how they are muxed, so
it makes sense to allow this for GPIOs as well.
Add the generic set_config function so that we can rely on the existing
pinctrl code we have.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Lines are usually ended with a semi-column in C, yet this was copied from a
structure declaration to the init variant while keeping the comma at the
end. Make sure we have a normal syntax, instead of multiple assignments.
Fixes: d83c82ce7ccd ("pinctrl: sunxi: support multiple pin controller")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The sunxi pinctrl only implements the pin_config_group_set callback at the
moment, whereas the gpiochip_generic_config function relies on
pin_config_set. Rework the functions a little to support pin_config_set,
and rely on it for pin_config_group_set.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Version 1.13c of pin list has some changes in pin names for
Intel Cedarfork.
Update the driver accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linar.org>
|
|
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.50 of Feb
12, 2019, the sel_ndfc MOD_SEL register bit is renamed to sel_ndf.
Update the pin control drivers to reflect this.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Update R-Car E3]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
According to the R-Car Gen3 Hardware Manual Errata for Rev 0.80 of Dec
22, 2017, and the Errata for Rev 1.50 of Dec 25, 2018, MOD_SEL0 register
bits 3, 4, 17, and 18 are renamed from SEL_ADG_{A,B,C} to
SEL_ADG{A,B,C}. Update the pin control drivers to reflect this.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.50 of
Feb 12, 2019, the RTS{0,1,3,4}_#/TANS pin names defined in the GPSR and
IPSR registers are renamed to RTS{0,1,3,4}_#.
This patch updates the pin control drivers to reflect this.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Update R-Car H3 ES1.x, V3M, V3H, and D3]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
Jun 4, 2018, the CC5_OSCOUT pin is removed. Update the pin control
drivers to reflect this.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Update R-Car V3M, V3H]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The HDMI CEC function is not supported by the R-Car Gen3 Hardware Manual
Rev 1.00. Therefore, delete the corresponding pin groups and functions,
and rename the HDMI[01]_CEC definitions to match their GPIO
functionality.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Squashed several commits]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of Aug
24, 2018, there is no need to configure MOD_SEL1 bit30 when the
SSI_SCK2_{A,B} or SSI_WS2_{A,B} pin functions are selected.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Remove now unused definitions, mark MOD_SEL1 bit30 reserved]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
Aug 24, 2018, there is no need to configure MOD_SEL1 bit31 when the
SIM0_D_{A,B} pin function is selected.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Remove now unused definitions, mark MOD_SEL1 bit31 reserved]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of Aug
24, 2018, the MOD_SEL0 bit16 must be set to 0 when the NFALE_A and
NFRB_N_A pin functions are selected.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
- The IPSR field is meant for documentation only,
- The function name refers to the pin function, not to the IPSR
field.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
|
|
rza1_get_bit() is just a single register read. Hence there's no need to
synchronize it with other register writes to the same bank.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
|
|
Add a run-time check to the PINMUX_CFG_REG_VAR() macro, to ensure the
number of provided enum IDs is correct. This cannot be done at build
time, as the number of values depends on the variable-width fields in
the config register.
This helps catching bugs early.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add build-time checks to the PINMUX_CFG_REG() and PINMUX_DATA_REG()
macros, to ensure the number of provided enum IDs is correct.
This helps catching bugs early.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Currently the PINMUX_DATA_REG() macro must be followed by initialization
data, specifying all enum IDs. Hence the macro itself does not know
anything about the enum IDs, preventing the macro from performing any
validation on it.
Make the macro accept the enum IDs as a parameter, and update all users.
Note that array data enclosed by curly braces cannot be passed to a
macro as a parameter, hence the enum IDs are wrapped using the GROUP()
macro.
No functional changes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Currently the PINMUX_CFG_REG_VAR() macro must be followed by
initialization data, specifying all enum IDs. Hence the macro itself
does not know anything about the enum IDs, preventing the macro from
performing any validation on it.
Make the macro accept the enum IDs as a parameter, and update all users.
Note that array data enclosed by curly braces cannot be passed to a
macro as a parameter, hence both the register field widths and the enum
IDs are wrapped using the GROUP() macro.
No functional changes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Currently the PINMUX_CFG_REG() macro must be followed by initialization
data, specifying all enum IDs. Hence the macro itself does not know
anything about the enum IDs, preventing the macro from performing any
validation on it.
Make the macro accept the enum IDs as a parameter, and update all users.
Note that array data enclosed by curly braces cannot be passed to a
macro as a parameter, hence the enum IDs are wrapped using a new macro
GROUPS().
No functional changes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Enable compile-testing of all Renesas SuperH and ARM pin control
drivers, in a similar way as was done before for clock and SoC drivers
in commits 371dd373c6edd557 ("clk: renesas: Allow compile-testing of all
(sub)drivers") and 8be381a131c29c47 ("soc: renesas: Rework Kconfig and
Makefile logic").
The SuperH pin control drivers need specific include files, hence make
sure they are always found when compile-testing.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Source files using -Exxx error codes should include <linux/errno.h>.
On ARM, this header file is included indirectly; on SuperH, it is not,
leading to "error: ‘EINVAL’ undeclared" failures when enabling
compile-testing later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Pinctrl drivers for SuperH platforms use legacy function GPIOs.
Currently this support is compiled in based on the SUPERH platform
dependency, which hinders the introduction of compile-testing support
for the affected pinctrl drivers.
Introduce a new Kconfig symbol PINCTRL_SH_FUNC_GPIO, which is
auto-selected when needed. This symbol in turn selects
PINCTRL_SH_PFC_GPIO, to reduce the number of per-driver selects.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Perform some basic sanity checks on all built-in pinmux tables when
DEBUG is defined, to help catching bugs early.
For now the following checks are included:
- Check register and field widths in descriptors for config registers
with variable-width fields,
- Check relations between pin groups and functions:
- All pin functions must refer to existing pin groups,
- All pin groups must be referred to by a pin function,
- Warn if a pin group is referred to by multiple pin functions
(which is OK for backwards-compatibility aliases),
- Provide suggestions for reducing table sizes: reserved fields of
more than 3 bits can better be split in smaller subfields, as the
storage need is proportional to the square of the width of the
(sub)field,
Note that a dummy non-matching entry is added to the DT match table for
checking r8a7795es1_pinmux_info, as R-Car H3 ES1.0 is matched using
soc_device_match() in r8a7795_pinmux_init(), instead of by the DT match
table.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The TDSELCTRL register is responsible for configuring the SDHI/MMC clock
return path delay and may be adjusted by the bootloader. Retain the value
across suspend/resume to prevent hardware instability after resume.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
CANFD is found also on the R8A774C0, therefore move CANFD pin
groups and functions to "common".
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
CANFD is found also on the R8A774A1, therefore move CANFD pin
groups and functions to "common".
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Adds HSCIF0 and HSCIF1 pins, groups and functions for R8A7779.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The R-Car Gen3 HardWare Manual Errata for Rev. 1.00 (Jul 2, 2018)
renamed the various miscellaneous I/O control registers (IOCTRLx) on
R-Car E3, to reflect better their actual purposes, and matching other
SoCs.
Update the code to match this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
|
|
The R-Car Gen3 HardWare Manual Errata for Rev. 1.00 (Jul 2, 2018)
renamed the various miscellaneous I/O control registers (IOCTRLx) on
R-Car V3H, to reflect better their actual purposes, and matching other
SoCs.
Update the code to match this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
|
|
The R-Car Gen3 HardWare Manual Errata for Rev. 1.00 (Jul 2, 2018)
renamed the various miscellaneous I/O control registers (IOCTRLx) on
R-Car V3M, to reflect better their actual purposes, and matching other
SoCs.
Update the code to match this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
|
|
saved-context in byt_gpio_probe is allocated via devm_kcalloc and is
used without checking for NULL in later functions. This patch avoids
such a scenario.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is a calm cycle, not much happened this time around: not even
much incremental development. Some three new drivers, that is all.
No core changes.
New drivers:
- NXP (ex Freescale) i.MX 8QM driver.
- NXP (ex Freescale) i.MX 8MM driver.
- AT91 SAM9X60 subdriver.
Improvements:
- Support for external interrups (EINT) on Mediatek virtual GPIOs.
- Make BCM2835 pin config fully generic.
- Lots of Renesas SH-PFC incremental improvements"
* tag 'pinctrl-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (70 commits)
pinctrl: imx: fix scu link errors
dt-bindings: pinctrl: Document the i.MX50 IOMUXC binding
pinctrl: qcom: spmi-gpio: Reorder debug print
pinctrl: nomadik: fix possible object reference leak
pinctrl: stm32: return error upon hwspinlock failure
pinctrl: stm32: fix memory leak issue
pinctrl: sh-pfc: r8a77965: Add DRIF pins, groups and functions
pinctrl: sh-pfc: r8a77965: Add TMU pins, groups and functions
pinctrl: sh-pfc: Validate fixed-size field widths at build time
pinctrl: sh-pfc: sh73a0: Fix fsic_spdif pin groups
pinctrl: sh-pfc: r8a7792: Fix vin1_data18_b pin group
pinctrl: sh-pfc: r8a7791: Fix scifb2_data_c pin group
pinctrl: sh-pfc: emev2: Add missing pinmux functions
pinctrl: sunxi: Support I/O bias voltage setting on A80
pinctrl: ingenic: Add LCD pins for the JZ4725B SoC
pinctrl: samsung: Remove legacy API for handling external wakeup interrupts mask
pinctrl: bcm2835: Direct GPIO config changes to generic pinctrl
pinctrl: bcm2835: declare pin config as generic
pinctrl: qcom: qcs404: Drop unused UFS_RESET macro
dt-bindings: add documentation for slew rate
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.1 cycle:
Core changes:
- The big change this time around is the irqchip handling in the
qualcomm pin controllers, closely coupled with the gpiochip. This
rework, in a classic fall-between-the-chairs fashion has been
sidestepped for too long.
The Qualcomm IRQchips using the SPMI and SSBI transport mechanisms
have been rewritten to use hierarchical irqchip. This creates the
base from which I intend to gradually pull support for hierarchical
irqchips into the gpiolib irqchip helpers to cut down on duplicate
code.
We have too many hacks in the kernel because people have been
working around the missing hierarchical irqchip for years, and once
it was there, noone understood it for a while. We are now slowly
adapting to using it.
This is why this pull requests include changes to MFD, SPMI,
IRQchip core and some ARM Device Trees pertaining to the Qualcomm
chip family. Since Qualcomm have so many chips and such large
deployments it is paramount that this platform gets this right, and
now it (hopefully) does.
- Core support for pull-up and pull-down configuration, also from the
device tree. When a simple GPIO chip supports an "off or on" pull-up
or pull-down resistor, we provide a way to set this up using
machine descriptors or device tree.
If more elaborate control of pull up/down (such as resistance shunt
setting) is required, drivers should be phased over to use pin
control. We do not yet provide a userspace ABI for this pull
up-down setting but I suspect the makers are going to ask for it
soon enough. PCA953x is the first user of this new API.
- The GPIO mockup driver has been revamped after some discussion
improving the IRQ simulator in the process.
The idea is to make it possible to use the mockup for both testing
and virtual prototyping, e.g. when you do not yet have a GPIO
expander to play with but really want to get something to develop
code around before hardware is available. It's neat. The blackbox
testing usecase is currently making its way into kernelci.
- ACPI GPIO core preserves non direction flags when updating flags.
- A new device core helper for devm_platform_ioremap_resource() is
funneled through the GPIO tree with Greg's ACK.
New drivers:
- TQ-Systems QTMX86 GPIO controllers (using port-mapped I/O)
- Gateworks PLD GPIO driver (vaccumed up from OpenWrt)
- AMD G-Series PCH (Platform Controller Hub) GPIO driver.
- Fintek F81804 & F81966 subvariants.
- PCA953x now supports NXP PCAL6416.
Driver improvements:
- IRQ support on the Nintendo Wii (Hollywood) GPIO.
- get_direction() support for the MVEBU driver.
- Set the right output level on SAMA5D2.
- Drop the unused irq trigger setting on the Spreadtrum driver.
- Wakeup support for PCA953x.
- A slew of cleanups in the various Intel drivers"
* tag 'gpio-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (110 commits)
gpio: gpio-omap: fix level interrupt idling
gpio: amd-fch: Set proper output level for direction_output
x86: apuv2: remove unused variable
gpio: pca953x: Use PCA_LATCH_INT
platform/x86: fix PCENGINES_APU2 Kconfig warning
gpio: pca953x: Fix dereference of irq data in shutdown
gpio: amd-fch: Fix type error found by sparse
gpio: amd-fch: Drop const from resource
gpio: mxc: add check to return defer probe if clock tree NOT ready
gpio: ftgpio: Register per-instance irqchip
gpio: ixp4xx: Add DT bindings
x86: pcengines apuv2 gpio/leds/keys platform driver
gpio: AMD G-Series PCH gpio driver
drivers: depend on HAS_IOMEM for devm_platform_ioremap_resource()
gpio: tqmx86: Set proper output level for direction_output
gpio: sprd: Change to use SoC compatible string
gpio: sprd: Use SoC compatible string instead of wildcard string
gpio: of: Handle both enable-gpio{,s}
gpio: of: Restrict enable-gpio quirk to regulator-gpio
gpio: davinci: use devm_platform_ioremap_resource()
...
|
|
Currently PINCTRL_IMX8QM and PINCTRL_IMX8QXP will select PINCTRL_IMX_SCU.
However, PINCTRL_IMX_SCU may not be valid due to it depends on IMX_MBOX.
Then we may meet the following link errors:
ld: drivers/pinctrl/freescale/pinctrl-scu.o: in function `imx_pinctrl_sc_ipc_init':
pinctrl-scu.c:(.text+0x10): undefined reference to `imx_scu_get_handle'
ld: pinctrl-scu.c:(.text+0x10): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `imx_scu_get_handle'
ld: drivers/pinctrl/freescale/pinctrl-scu.o: in function `imx_pinconf_get_scu':
pinctrl-scu.c:(.text+0xa0): undefined reference to `imx_scu_call_rpc'
ld: pinctrl-scu.c:(.text+0xa0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `imx_scu_call_rpc'
ld: drivers/pinctrl/freescale/pinctrl-scu.o: in function `imx_pinconf_set_scu':
pinctrl-scu.c:(.text+0x1b4): undefined reference to `imx_scu_call_rpc'
ld: pinctrl-scu.c:(.text+0x1b4): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `imx_scu_call_rpc'
ld: drivers/pinctrl/freescale/pinctrl-imx8qxp.o: in function `imx8qxp_pinctrl_probe':
pinctrl-imx8qxp.c:(.text+0x28): undefined reference to `imx_pinctrl_probe'
ld: pinctrl-imx8qxp.c:(.text+0x28): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `imx_pinctrl_probe'
Rework so that PINCTRL_IMX8QM and PINCTRL_IMX8QXP depends on IMX_SCU
as well in case they're wrongly enabled.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
It's reasonable to expect that people turn to the "gpio" debugfs file to
first and foremost learn about the direction and value of a gpio, and
second to that about it's pinconf. So reorder the value so each line
reads:
gpioN: direction value ...
This also makes it consistent with the TLMM pinctrl driver's output in
the same dump.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
The of_find_device_by_node takes a reference to the struct device
when find the match device ,we should release it when fail.
Signed-off-by: WangBo <wang.bo116@zte.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Return error to the caller when the hwspinlock can't get locked.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
configs is allocated by pinconf_generic_parse_dt_config(),
pinctrl_utils_add_map_configs() duplicates configs so it can and has to
be freed to prevent memory leaks.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fix the mismatch between the "sdxc_d13_1_a" pin group definition from
meson8b_cbus_groups and the entry in sdxc_a_groups ("sdxc_d0_13_1_a").
This makes it possible to use "sdxc_d13_1_a" in device-tree files to
route the MMC data 1..3 pins to GPIOX_1..3.
Fixes: 0fefcb6876d0d6 ("pinctrl: Add support for Meson8b")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio updates for v5.1
- support for a new variant of pca953x
- documentation fix from Wolfram
- some tegra186 name changes
- two minor fixes for madera and altera-a10sr
|
