| Age | Commit message (Collapse) | Author |
|---|
|
Pass pointer to the TD (struct xhci_td *) directly, instead of its
components separately.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-19-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If this quirk was set then driver would treat transfer events with
'Success' completion code as 'Short packet' if there were untransferred
bytes left.
This is so common that turn it into default behavior.
xhci_warn_ratelimited() is no longer used after this, so remove it.
A success event with untransferred bytes left doesn't always mean a
misbehaving controller. If there was an error mid a multi-TRB TD it's
allowed to issue a success event for the last TRB in that TD.
See xhci 1.2 spec 4.9.1 Transfer Descriptors
"Note: If an error is detected while processing a multi-TRB TD, the xHC
shall generate a Transfer Event for the TRB that the error was detected
on with the appropriate error Condition Code, then may advance to the
next TD. If in the process of advancing to the next TD, a Transfer TRB
is encountered with its IOC flag set, then the Condition Code of the
Transfer Event generated for that Transfer TRB should be Success,
because there was no error actually associated with the TRB that
generated the Event. However, an xHC implementation may redundantly
assert the original error Condition Code."
Co-developed-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Print the full hex value of PORTSC register in addition to the human
readable decoded string while debugging PORTSC value.
If PORTSC value is 0xffffffff then don't decode it.
This lets us inspect Rsvd bits of PORTSC.
Same is done for USBSTS register values.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
'erst_size' represents the maximum capacity of entries that ERST can hold,
while 'num_entries' indicates the actual number of entries currently held
in the ERST. These two values are identical because the xhci driver does
not support ERST expansion. Thus, 'erst_size' is removed.
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Check if requested segments ('segs' or 'ERST_DEFAULT_SEGS') exceeds the
maximum amount ERST supports.
When 'segs' is '0', 'ERST_DEFAULT_SEGS' is used instead. But both values
may not exceed ERST max.
Macro 'ERST_MAX_SEGS' is renamed to 'ERST_DEFAULT_SEGS'. The new name
better represents the macros, which is the number of Event Ring segments
to allocate, when the amount is not specified.
Additionally, rename and change xhci_create_secondary_interrupter()'s
argument 'int num_segs' to 'unsigned int segs'. This makes it the same
as its counter part in xhci_alloc_interrupter().
Fixes: c99b38c41234 ("xhci: add support to allocate several interrupters")
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Port capability flags for USB2 ports have been cached in an
u32 xhci->ext_caps[] array long before the driver had struct xhci_port
and struct xhci_port_cap structures.
Move these cached USB2 port capability values together with the other
port capability values into struct xhci_port_cap cability structure.
This also gets rid of the cumbersome way of mapping port to USB2
capability based on portnum as each port has a pointer to its capability
structure.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Slot ID is a index of a virtual device in struct 'xhci_hcd->devs[]'.
Previously, to get the slot ID associated with a port, we had to loop
through all devices and compare ports, which is very inefficient.
Instead, the slot ID (of the device which is directly connected to the
port), is added to the its corresponding 'xhci_port' struct. As a result,
finding the port's device is quick and easy.
Function 'xhci_find_slot_id_by_port()' is removed, as it is no longer
needed.
Signed-off-by: Niklas Neronin <niklas.neronin@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Variables real & fake port do not convey their purpose, thus they are
replaced with a pointer to the root hub port 'struct xhci_port *rhub_port'.
'rhub_port' contains real & fake ports in zero-based format, which happens
to be more widely used inside the xHCI driver:
- 'real_port' is ('rhub_port->hw_portnum' + 1)
- 'fake_port' is ('rhub_port->hcd_portnum' + 1)
One reason for real port being one-based, is to signal other functions in
case struct 'xhci_virt_device' initialization failed, in this case the
value will remain 0. This is no longer needed, instead we check whether
or not 'rhub_port' is 'NULL'.
Signed-off-by: Niklas Neronin <niklas.neronin@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 9affb1d9a9d9918adff519a129daba5e369dd741.
It's not ready to be merged, based on reviews.
Reported-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/96ab6033-2cb9-daa7-ddad-090138896739@linux.intel.com
Cc: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Expose xhci_stop_endpoint_sync() which is a synchronous variant of
xhci_queue_stop_endpoint(). This is useful for client drivers that are
using the secondary interrupters, and need to stop/clean up the current
session. The stop endpoint command handler will also take care of cleaning
up the ring.
Modifications to repurpose the new API into existing stop endpoint
sequences was implemented by Wesley Cheng.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Co-developed-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-11-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
isoc_bei_interval is used to balance how often completed isochronous
events cause interrupts. If interval is too large then the event ring
may fill up before the completed isoc TRBs are handled.
isoc_bei_interval is tuned based on how full the event ring is.
isoc_bei_interval variable needs to be per interrupter as
with several interrupters each one has its own event ring.
move isoc_bei_interval variable to the interrupter structure.
if a secondary interrupter does not care about this feature then
keep isoc_bei_interval 0.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-4-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Each interrupter has an interrupt pending (IP) bit that should be cleared
in the interrupt handler. This is done automatically for systems using
MSI/MSI-X interrupts.
Secondary interrupters used by audio offload may not actually trigger
MSI/MSI-X messages, so driver may need to clear the IP bit manually for
these, even if the primary interrupter IP is cleared automatically.
Add an ip_autoclear flag to each interrupter that driver can configure
when requesting an interrupt for that xHC interrupter, and move
the interrupt pending clearing code to its own helper function.
Use this ip_autoclear flag instead of the current hcd->msi_enabled
to check if IP flag is cleared by software.
[Moved ip_autoclear into xhci and set based on msi_enabled -wcheng]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240217001017.29969-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Split the PORT and CAPs macro definitions into a separate file to
facilitate sharing with other files without the need to include the entire
xhci.h.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20240124152525.3910311-2-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The last TRB of a isoc TD might not trigger an event if there was
an error event for a TRB mid TD. This is seen on a NEC Corporation
uPD720200 USB 3.0 Host
After an error mid a multi-TRB TD the xHC should according to xhci 4.9.1
generate events for passed TRBs with IOC flag set if it proceeds to the
next TD. This event is either a copy of the original error, or a
"success" transfer event.
If that event is missing then the driver and xHC host get out of sync as
the driver is still expecting a transfer event for that first TD, while
xHC host is already sending events for the next TD in the list.
This leads to
"Transfer event TRB DMA ptr not part of current TD" messages.
As a solution we tag the isoc TDs that get error events mid TD.
If an event doesn't match the first TD, then check if the tag is
set, and event points to the next TD.
In that case give back the fist TD and process the next TD normally
Make sure TD status and transferred length stay valid in both cases
with and without final TD completion event.
Reported-by: Michał Pecio <michal.pecio@gmail.com>
Closes: https://lore.kernel.org/linux-usb/20240112235205.1259f60c@foxbook/
Tested-by: Michał Pecio <michal.pecio@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240125152737.2983959-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Modify the XHCI drivers to accommodate for handling multiple event rings in
case there are multiple interrupters. Add the required APIs so clients are
able to allocate/request for an interrupter ring, and pass this information
back to the client driver. This allows for users to handle the resource
accordingly, such as passing the event ring base address to an audio DSP.
There is no actual support for multiple MSI/MSI-X vectors.
[export xhci_initialize_ring_info() -wcheng]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20240102214549.22498-2-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Instead of variable 'msix_count' containing the number of MSI-X vectors,
now it can contains MSI or MSI-X vector amount. Because both interrupt
methods allow several vectors. Thus, 'msix_count' is renamed to 'nvecs'.
Additionally, instead of storing the maximum possible vector amount,
now it stores the amount of successfully allocated vectors, or negative
integer on allocation failure.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-16-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
- The HCD address_device callback now accepts a user-defined timeout value
in milliseconds, providing better control over command execution times.
- The default timeout value for the address_device command has been set
to 5000 ms, aligning with the USB 3.2 specification. However, this
timeout can be adjusted as needed.
- The xhci_setup_device function has been updated to accept the timeout
value, allowing it to specify the maximum wait time for the command
operation to complete.
- The hub driver has also been updated to accommodate the newly added
timeout parameter during the SET_ADDRESS request.
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Reviewed-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231027152029.104363-1-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt changes for 6.7-rc1.
Nothing really major in here, just lots of constant development for
new hardware. Included in here are:
- Thunderbolt (i.e. USB4) fixes for reported issues and support for
new hardware types and devices
- USB typec additions of new drivers and cleanups for some existing
ones
- xhci cleanups and expanded tracing support and some platform
specific updates
- USB "La Jolla Cove Adapter (LJCA)" support added, and the gpio,
spi, and i2c drivers for that type of device (all acked by the
respective subsystem maintainers.)
- lots of USB gadget driver updates and cleanups
- new USB dwc3 platforms supported, as well as other dwc3 fixes and
cleanups
- USB chipidea driver updates
- other smaller driver cleanups and additions, full details in the
shortlog
All of these have been in the linux-next tree for a while with no
reported problems"
* tag 'usb-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (167 commits)
usb: gadget: uvc: Add missing initialization of ssp config descriptor
usb: storage: set 1.50 as the lower bcdDevice for older "Super Top" compatibility
usb: raw-gadget: report suspend, resume, reset, and disconnect events
usb: raw-gadget: don't disable device if usb_ep_queue fails
usb: raw-gadget: properly handle interrupted requests
usb:cdnsp: remove TRB_FLUSH_ENDPOINT command
usb: gadget: aspeed_udc: Convert to platform remove callback returning void
dt-bindings: usb: fsa4480: Add compatible for OCP96011
usb: typec: fsa4480: Add support to swap SBU orientation
dt-bindings: usb: fsa4480: Add data-lanes property to endpoint
usb: typec: tcpm: Fix NULL pointer dereference in tcpm_pd_svdm()
Revert "dt-bindings: usb: Add bindings for multiport properties on DWC3 controller"
Revert "dt-bindings: usb: qcom,dwc3: Add bindings for SC8280 Multiport"
thunderbolt: Fix one kernel-doc comment
usb: gadget: f_ncm: Always set current gadget in ncm_bind()
usb: core: Remove duplicated check in usb_hub_create_port_device
usb: typec: tcpm: Add additional checks for contaminant
arm64: dts: rockchip: rk3588s: Add USB3 host controller
usb: dwc3: add optional PHY interface clocks
dt-bindings: usb: add rk3588 compatible to rockchip,dwc3
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening updates from Kees Cook:
"One of the more voluminous set of changes is for adding the new
__counted_by annotation[1] to gain run-time bounds checking of
dynamically sized arrays with UBSan.
- Add LKDTM test for stuck CPUs (Mark Rutland)
- Improve LKDTM selftest behavior under UBSan (Ricardo Cañuelo)
- Refactor more 1-element arrays into flexible arrays (Gustavo A. R.
Silva)
- Analyze and replace strlcpy and strncpy uses (Justin Stitt, Azeem
Shaikh)
- Convert group_info.usage to refcount_t (Elena Reshetova)
- Add __counted_by annotations (Kees Cook, Gustavo A. R. Silva)
- Add Kconfig fragment for basic hardening options (Kees Cook, Lukas
Bulwahn)
- Fix randstruct GCC plugin performance mode to stay in groups (Kees
Cook)
- Fix strtomem() compile-time check for small sources (Kees Cook)"
* tag 'hardening-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (56 commits)
hwmon: (acpi_power_meter) replace open-coded kmemdup_nul
reset: Annotate struct reset_control_array with __counted_by
kexec: Annotate struct crash_mem with __counted_by
virtio_console: Annotate struct port_buffer with __counted_by
ima: Add __counted_by for struct modsig and use struct_size()
MAINTAINERS: Include stackleak paths in hardening entry
string: Adjust strtomem() logic to allow for smaller sources
hardening: x86: drop reference to removed config AMD_IOMMU_V2
randstruct: Fix gcc-plugin performance mode to stay in group
mailbox: zynqmp: Annotate struct zynqmp_ipi_pdata with __counted_by
drivers: thermal: tsens: Annotate struct tsens_priv with __counted_by
irqchip/imx-intmux: Annotate struct intmux_data with __counted_by
KVM: Annotate struct kvm_irq_routing_table with __counted_by
virt: acrn: Annotate struct vm_memory_region_batch with __counted_by
hwmon: Annotate struct gsc_hwmon_platform_data with __counted_by
sparc: Annotate struct cpuinfo_tree with __counted_by
isdn: kcapi: replace deprecated strncpy with strscpy_pad
isdn: replace deprecated strncpy with strscpy
NFS/flexfiles: Annotate struct nfs4_ff_layout_segment with __counted_by
nfs41: Annotate struct nfs4_file_layout_dsaddr with __counted_by
...
|
|
In some situations where xhci removal happens parallel to xhci_handshake,
we encounter a scenario where the xhci_handshake can't succeed, and it
polls until timeout.
If xhci_handshake runs until timeout it can on some platforms result in
a long wait which might lead to a watchdog timeout.
Add a helper that checks xhci status during the handshake, and exits if
set state is entered. Use this helper in places where xhci_handshake is
called unlocked and has a long timeout. For example xhci command timeout
and xhci reset.
[commit message and code comment rewording -Mathias]
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-18-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xhci_alloc_erst() has global scope even though it's only used in
xhci-mem.c. Declare it static.
xhci_free_erst() was removed by commit b17a57f89f69 ("xhci: Refactor
interrupter code for initial multi interrupter support."), but a
declaration in xhci.h still remains. Drop it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit ebd88cf50729 ("xhci: Remove unused defines for ERST_SIZE and
ERST_ENTRIES") removed the ERST_SIZE macro but retained a code comment
explaining the quantity chosen in the macro.
Remove the code comment as well.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Mathias notes that the ERST_PTR_MASK macro is named as if it's masking
the Event Ring Dequeue Pointer in the ERDP register, but in actuality
it's masking the inverse.
Invert the macro's value for clarity.
Migrate it to the modern GENMASK_ULL() syntax to avoid u64 casts.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Users have reported log spam created by "Event Ring Full" xHC event
TRBs. These are caused by interrupt latency in conjunction with a very
busy set of devices on the bus. The errors are benign, but throughput
will suffer as the xHC will pause processing of transfers until the
Event Ring is drained by the kernel.
Commit dc0ffbea5729 ("usb: host: xhci: update event ring dequeue pointer
on purpose") mitigated the issue by advancing the Event Ring Dequeue
Pointer already after half a segment has been processed. Nevertheless,
providing a larger Event Ring would be useful to cope with load peaks.
Expand the number of event TRB slots available by increasing the number
of Event Ring segments in the ERST.
Controllers have a hardware-defined limit as to the number of ERST
entries they can process, but with up to 32k it can be excessively high
(sec 5.3.4). So cap the actual number at 2 (configurable through the
ERST_MAX_SEGS macro), which seems like a reasonable quantity. It is
supported by any xHC because the limit in the HCSPARAMS2 register is
defined as a power of 2. Renesas uPD720201 and VIA VL805 controllers
do not support more than 2 ERST entries.
An alternative to increasing the number of Event Ring segments would be
an increase of the segment size. But that requires allocating multiple
contiguous pages, which may be impossible if memory is fragmented.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When using more than one Event Ring segment (ERSTSZ > 1), software shall
set the DESI bits in the ERDP register to the number of the segment to
which the upper ERDP bits are pointing. The xHC may use the DESI bits
as a shortcut to determine whether it needs to check for an Event Ring
Full condition: If it's enqueueing events in a different segment, it
need not compare its internal Enqueue Pointer with the Dequeue Pointer
in the upper bits of the ERDP register (sec 5.5.2.3.3).
Not setting the DESI bits correctly can result in the xHC enqueueing
events past the Dequeue Pointer. On Renesas uPD720201 host controllers,
incorrect DESI bits cause an interrupt storm. For comparison, VIA VL805
host controllers do not exhibit such problems. Perhaps they do not take
advantage of the optimization afforded by the DESI bits.
To fix the issue, assign the segment number to each struct xhci_segment
in xhci_segment_alloc(). When advancing the Dequeue Pointer in
xhci_update_erst_dequeue(), write the segment number to the DESI bits.
On driver probe, set the DESI bits to zero in xhci_set_hc_event_deq() as
processing starts in segment 0. Likewise on driver teardown, clear the
DESI bits to zero in xhci_free_interrupter() when clearing the upper
bits of the ERDP register. Previously those functions (incorrectly)
treated the DESI bits as if they're declared RsvdP.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB and Thunderbolt fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct urb_priv.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: linux-usb@vger.kernel.org
Link: https://lore.kernel.org/r/20230915195812.never.371-kees@kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
xhci_add_interrupter() erroneously preserves only the lowest 4 bits when
writing the ERSTBA register, not the lowest 6 bits. Fix it.
Migrate the ERST_BASE_RSVDP macro to the modern GENMASK_ULL() syntax to
avoid a u64 cast.
This was previously fixed by commit 8c1cbec9db1a ("xhci: fix event ring
segment table related masks and variables in header"), but immediately
undone by commit b17a57f89f69 ("xhci: Refactor interrupter code for
initial multi interrupter support.").
Fixes: b17a57f89f69 ("xhci: Refactor interrupter code for initial multi interrupter support.")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v6.3+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230915143108.1532163-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
DWC3 driver needs access to XHCI Extended Capabilities registers to
read number of usb2 ports and usb3 ports present on multiport controller.
Since the extcaps header is sufficient to parse this info, move port_count
related macros and structure from xhci.h to xhci-ext-caps.h.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Link: https://lore.kernel.org/r/20230828133033.11988-4-quic_kriskura@quicinc.com
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some ZHAOXIN xHCI controllers follow usb3.1 spec, but only support
gen1 speed 5Gbps. While in Linux kernel, if xHCI suspport usb3.1,
root hub speed will show on 10Gbps.
To fix this issue of ZHAOXIN xHCI platforms, read usb speed ID
supported by xHCI to determine root hub speed. And add a quirk
XHCI_ZHAOXIN_HOST for this issue.
[fix warning about uninitialized symbol -Mathias]
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-11-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On some ZHAOXIN hosts, xHCI will prefetch TRB for performance
improvement. However this TRB prefetch mechanism may cross page boundary,
which may access memory not allocated by xHCI driver. In order to fix
this issue, two pages was allocated for a segment and only the first
page will be used. And add a quirk XHCI_ZHAOXIN_TRB_FETCH for this issue.
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-10-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Trying to keep track of free trbs in a ring by adding and subtracting
deltas each time a enqueue or dequeue is increased or moved has proven to
be buggy and complicated, especially over long periods of time.
Recently a bug in counting free trbs was fixed, now taking into account
cancelled URBs that were turned into no-ops, preventing free_trbs to
slowly wander off causing unnecessary ring expansion. See
commit fe82f16aafda ("xhci: Fix incorrect tracking of free space on
transfer rings")
Turns out its a lot easier to just calculate the numer of free TRB
based on ring size and the current enqueue and dequeue pointer values.
This is currently only needed for the command ring as multi segment
transfer rings already ensures there is enough room the ring during
the ring expansion check.
We could get rid of the ring->num_trbs_free entry completely, but as
the xhci DbC code also uses it we don't clean that up in this patch.
Reported-by: Miller Hunter <MillerH@hearthnhome.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217242
Tested-by: Miller Hunter <MillerH@hearthnhome.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-8-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The XHCI_PLAT quirk was only needed to ensure non-PCI xHC host avoided
setting up MSI interrupts in generic xhci codepaths.
The MSI setup code is now moved to PCI specific xhci-pci.c file so
the quirk is no longer needed.
Remove setting the XHCI_PLAT quirk for HiSilocon SoC xHC, NVIDIA Tegra xHC,
MediaTek xHC, the generic xhci-plat driver, and the checks for XHCI_PLAT
in xhci-pci.c MSI setup code.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-5-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here and this resolves merge conflicts in:
drivers/usb/dwc3/gadget.c
drivers/usb/gadget/udc/core.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Donghun reports that a notebook that has an AMD Ryzen 5700U but supports
S3 has problems with USB after resuming from suspend. The issue was
bisected down to commit d1658268e439 ("usb: pci-quirks: disable D3cold on
xhci suspend for s2idle on AMD Renoir").
As this issue only happens on S3, narrow the broken D3cold quirk to only
run in s2idle.
Fixes: d1658268e439 ("usb: pci-quirks: disable D3cold on xhci suspend for s2idle on AMD Renoir")
Reported-and-tested-by: Donghun Yoon <donghun.yoon@lge.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230515134059.161110-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, the pci_resume method has only a flag indicating whether the
system is resuming from hibernation. In order to handle all PM events like
AUTO_RESUME (runtime resume from device in D3), RESUME (system resume from
s2idle, S3 or S4 states) etc change the pci_resume method to handle all PM
events.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230428140056.1318981-2-Basavaraj.Natikar@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move function to cleanup MSI from xhci.c to xhci-pci.c
This is to decouple PCI specific code from generic xhci code.
No functional changes, function is an exact copy
Signed-off-by: Josue David Hernandez Gutierrez <josue.d.hernandez.gutierrez@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230317154715.535523-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Call the PCI specific MSI/MSIX interrupt freeing code from the xhci-pci
callbacks instead of generic xhci code, decoupling PCI parts from
generic xhci functions.
Adds xhci_pci_stop() that overrides xhci_stop() for PCI xHC controllers.
This will free MSIX interrupts a bit later in the hc_driver stop
callback, but is still earlier than usb core frees "legacy" interrupts,
or interrupts for other hosts.
Signed-off-by: Josue David Hernandez Gutierrez <josue.d.hernandez.gutierrez@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230317154715.535523-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move functions to setup msi from xhci.c to xhci-pci.c to decouple
PCI specific code from generic xhci code.
No functional changes, functions are an exact copy
[commit message rewording -Mathias]
Signed-off-by: Josue David Hernandez Gutierrez <josue.d.hernandez.gutierrez@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230317154715.535523-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xhci MSI setup is currently done at the same time as xHC host is started
in xhci_run(). This couples the generic xhci code with PCI, and will
reconfigure MSI/MSIX interrupts every time xHC is started.
Decouple MSI/MSIX configuration from generic xhci code by moving MSI/MSIX
part to a PCI specific xhci_pci_run() function overriding xhci_run().
This allows us to remove unnecessay MSI/MSIX reconfiguration done every
time PCI xhci resumes from suspend. i.e. remove the xhci_cleanup_msix()
call from xhci_resume() and the xhci_try_enale_msi() call in xhci_run()
called a bit later by xhci_resume()
[minor changes and commit message rewrite -Mathias]
Signed-off-by: Josue David Hernandez Gutierrez <josue.d.hernandez.gutierrez@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230317154715.535523-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
resume_done is just a timestamp, avoid confusing it with completions
related to port state transitions that are named *_done
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230202150505.618915-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that we have a port structure for each port it makes sense to
move per port variables, timestamps and completions there.
Get rid of storing bitfileds and arrays of port specific items per bus.
Move
unsigned long resume_done;
insigned long rexit_ports
struct completion rexit_done;
struct completion u3exit_done;
Rename rexit_ports to rexit_active, and remove a redundant hcd
speed check while checking if rexit_active is set.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230202150505.618915-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xHC supports several interrupters, each with its own mmio register set,
event ring and MSI/MSI-X vector. Transfers can be assigned different
interrupters when queued. See xhci 4.17 for details.
Current driver only supports one interrupter.
Create a xhci_interrupter structure containing an event ring, pointer to
mmio registers for this interrupter, variables to store registers over s3
suspend, erst, etc. Add functions to create and free an interrupter, and
pass an interrupter pointer to functions that deal with events.
Secondary interrupters are also useful without having an interrupt vector.
One use case is the xHCI audio sideband offloading where a DSP can take
care of specific audio endpoints.
When all transfer events of an offloaded endpoint can be mapped to a
separate interrupter event ring the DSP can poll this ring, and we can mask
these events preventing waking up the CPU.
Only minor functional changes such as clearing some of the interrupter
registers when freeing the interrupter.
Still create only one primary interrupter.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230202150505.618915-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xHC controller can supports up to 1024 interrupters.
To fit these change the max_interrupters varable from u8 to u16.
Add a separate mask for the reserve and preserve bits [5:0] in the erst
base register and use it instead of the ERST_PRT_MASK.
ERSR_PTR_MASK [3:0] is intended for masking bits in the
event ring dequeue pointer register.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230202150505.618915-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here and this resolves merge conflicts as
reported in linux-next in the following files:
drivers/usb/host/xhci.c
drivers/usb/host/xhci.h
drivers/usb/typec/ucsi/ucsi.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a hub_control() callback to the xhci_driver_overrides structure to
allow host drivers to override the default hub_control function. This
is required for Tegra which requires device specific actions for power
management to be executed during USB state transitions.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221111101813.32482-2-jilin@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
One USB3 roothub port may support link power management, while another
root port on the same xHC can't due to different retimers used for
the ports.
This is the case with Intel Alder Lake, and possible future platforms
where retimers used for USB4 ports cause too long exit latecy to
enable native USB3 lpm U1 and U2 states.
Add a flag in the xhci port structure to indicate if the port is
lpm_incapable, and check it while calculating exit latency.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Allow PCI hosts to check and tune roothub and port settings
before the hub is up and running.
This override is needed to turn off U1 and U2 LPM for some ports
based on per port ACPI _DSM, _UPC, or possibly vendor specific mmio
values for Intel xHC hosts.
Usb core calls the host update_hub_device once it creates a hub.
Entering U1 or U2 link power save state on ports with this limitation
will cause link to fail, turning the usb device unusable in that setup.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure to also limit the amount of soft reset retries for transaction
errors on streams in cases where the transaction error event doesn't point
to any specific TRB.
In these cases we don't know the TRB or stream ring, but we do know which
endpoint had the error.
To keep error counting simple and functional, move the current err_count
from ring structure to endpoint structure.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221130091944.2171610-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
