summaryrefslogtreecommitdiff
path: root/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe.txt
blob: 05ec2a838c54b58ce84aee5f7129e002339781ef (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
* Freescale QUICC Engine module (QE)
This represents qe module that is installed on PowerQUICC II Pro.

NOTE:  This is an interim binding; it should be updated to fit
in with the CPM binding later in this document.

Basically, it is a bus of devices, that could act more or less
as a complete entity (UCC, USB etc ). All of them should be siblings on
the "root" qe node, using the common properties from there.
The description below applies to the qe of MPC8360 and
more nodes and properties would be extended in the future.

i) Root QE device

Required properties:
- compatible : should be "fsl,qe";
- model : precise model of the QE, Can be "QE", "CPM", or "CPM2"
- reg : offset and length of the device registers.
- bus-frequency : the clock frequency for QUICC Engine.
- fsl,qe-num-riscs: define how many RISC engines the QE has.
- fsl,qe-snums: This property has to be specified as '/bits/ 8' value,
  defining the array of serial number (SNUM) values for the virtual
  threads.

Optional properties:
- fsl,firmware-phandle:
    Usage: required only if there is no fsl,qe-firmware child node
    Value type: <phandle>
    Definition: Points to a firmware node (see "QE Firmware Node" below)
        that contains the firmware that should be uploaded for this QE.
        The compatible property for the firmware node should say,
        "fsl,qe-firmware".

Recommended properties
- brg-frequency : the internal clock source frequency for baud-rate
  generators in Hz.

Deprecated properties
- fsl,qe-num-snums: define how many serial number(SNUM) the QE can use
  for the threads. Use fsl,qe-snums instead to not only specify the
  number of snums, but also their values.

Example:
     qe@e0100000 {
	#address-cells = <1>;
	#size-cells = <1>;
	#interrupt-cells = <2>;
	compatible = "fsl,qe";
	ranges = <0 e0100000 00100000>;
	reg = <e0100000 480>;
	brg-frequency = <0>;
	bus-frequency = <179A7B00>;
	fsl,qe-snums = /bits/ 8 <
		0x04 0x05 0x0C 0x0D 0x14 0x15 0x1C 0x1D
		0x24 0x25 0x2C 0x2D 0x34 0x35 0x88 0x89
		0x98 0x99 0xA8 0xA9 0xB8 0xB9 0xC8 0xC9
		0xD8 0xD9 0xE8 0xE9>;
     }

* Multi-User RAM (MURAM)

Required properties:
- compatible : should be "fsl,qe-muram", "fsl,cpm-muram".
- mode : the could be "host" or "slave".
- ranges : Should be defined as specified in 1) to describe the
   translation of MURAM addresses.
- data-only : sub-node which defines the address area under MURAM
   bus that can be allocated as data/parameter

Example:

     muram@10000 {
	compatible = "fsl,qe-muram", "fsl,cpm-muram";
	ranges = <0 00010000 0000c000>;

	data-only@0{
		compatible = "fsl,qe-muram-data",
			     "fsl,cpm-muram-data";
		reg = <0 c000>;
	};
     };

* Interrupt Controller (IC)

Required properties:
- compatible : should be "fsl,qe-ic".
- reg : Address range of IC register set.
- interrupts : interrupts generated by the device.
- interrupt-controller : this device is a interrupt controller.

Example:

	qeic: interrupt-controller@80 {
		interrupt-controller;
		compatible = "fsl,qe-ic";
		#address-cells = <0>;
		#interrupt-cells = <1>;
		reg = <0x80 0x80>;
		interrupts = <95 2 0 0  94 2 0 0>;
	};

* Serial Interface Block (SI)

The SI manages the routing of eight TDM lines to the QE block serial drivers
, the MCC and the UCCs, for receive and transmit.

Required properties:
- compatible : must be "fsl,<chip>-qe-si". For t1040, must contain
  "fsl,t1040-qe-si".
- reg : Address range of SI register set.

Example:

	si1: si@700 {
		compatible = "fsl,t1040-qe-si";
		reg = <0x700 0x80>;
	};

* Serial Interface Block RAM(SIRAM)

store the routing entries of SI

Required properties:
- compatible : should be "fsl,<chip>-qe-siram". For t1040, must contain
  "fsl,t1040-qe-siram".
- reg : Address range of SI RAM.

Example:

	siram1: siram@1000 {
		compatible = "fsl,t1040-qe-siram";
		reg = <0x1000 0x800>;
	};

* QE Firmware Node

This node defines a firmware binary that is embedded in the device tree, for
the purpose of passing the firmware from bootloader to the kernel, or from
the hypervisor to the guest.

The firmware node itself contains the firmware binary contents, a compatible
property, and any firmware-specific properties.  The node should be placed
inside a QE node that needs it.  Doing so eliminates the need for a
fsl,firmware-phandle property.  Other QE nodes that need the same firmware
should define an fsl,firmware-phandle property that points to the firmware node
in the first QE node.

The fsl,firmware property can be specified in the DTS (possibly using incbin)
or can be inserted by the boot loader at boot time.

Required properties:
  - compatible
      Usage: required
      Value type: <string>
      Definition: A standard property.  Specify a string that indicates what
          kind of firmware it is.  For QE, this should be "fsl,qe-firmware".

   - fsl,firmware
      Usage: required
      Value type: <prop-encoded-array>, encoded as an array of bytes
      Definition: A standard property.  This property contains the firmware
          binary "blob".

Example:
	qe1@e0080000 {
		compatible = "fsl,qe";
		qe_firmware:qe-firmware {
			compatible = "fsl,qe-firmware";
			fsl,firmware = [0x70 0xcd 0x00 0x00 0x01 0x46 0x45 ...];
		};
		...
	};

	qe2@e0090000 {
		compatible = "fsl,qe";
		fsl,firmware-phandle = <&qe_firmware>;
		...
	};