diff options
Diffstat (limited to 'drivers/tty/serial/8250/8250_mtk.c')
| -rw-r--r-- | drivers/tty/serial/8250/8250_mtk.c | 29 |
1 files changed, 20 insertions, 9 deletions
diff --git a/drivers/tty/serial/8250/8250_mtk.c b/drivers/tty/serial/8250/8250_mtk.c index f4a0caa56f84..21053db93ff1 100644 --- a/drivers/tty/serial/8250/8250_mtk.c +++ b/drivers/tty/serial/8250/8250_mtk.c @@ -37,6 +37,7 @@ #define MTK_UART_IER_RTSI 0x40 /* Enable RTS Modem status interrupt */ #define MTK_UART_IER_CTSI 0x80 /* Enable CTS Modem status interrupt */ +#define MTK_UART_EFR 38 /* I/O: Extended Features Register */ #define MTK_UART_EFR_EN 0x10 /* Enable enhancement feature */ #define MTK_UART_EFR_RTS 0x40 /* Enable hardware rx flow control */ #define MTK_UART_EFR_CTS 0x80 /* Enable hardware tx flow control */ @@ -53,6 +54,12 @@ #define MTK_UART_TX_TRIGGER 1 #define MTK_UART_RX_TRIGGER MTK_UART_RX_SIZE +#define MTK_UART_FEATURE_SEL 39 /* Feature Selection register */ +#define MTK_UART_FEAT_NEWRMAP BIT(0) /* Use new register map */ + +#define MTK_UART_XON1 40 /* I/O: Xon character 1 */ +#define MTK_UART_XOFF1 42 /* I/O: Xoff character 1 */ + #ifdef CONFIG_SERIAL_8250_DMA enum dma_rx_status { DMA_RX_START = 0, @@ -169,7 +176,7 @@ static void mtk8250_dma_enable(struct uart_8250_port *up) MTK_UART_DMA_EN_RX | MTK_UART_DMA_EN_TX); serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); - serial_out(up, UART_EFR, UART_EFR_ECB); + serial_out(up, MTK_UART_EFR, UART_EFR_ECB); serial_out(up, UART_LCR, lcr); if (dmaengine_slave_config(dma->rxchan, &dma->rxconf) != 0) @@ -232,7 +239,7 @@ static void mtk8250_set_flow_ctrl(struct uart_8250_port *up, int mode) int lcr = serial_in(up, UART_LCR); serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); - serial_out(up, UART_EFR, UART_EFR_ECB); + serial_out(up, MTK_UART_EFR, UART_EFR_ECB); serial_out(up, UART_LCR, lcr); lcr = serial_in(up, UART_LCR); @@ -241,7 +248,7 @@ static void mtk8250_set_flow_ctrl(struct uart_8250_port *up, int mode) serial_out(up, MTK_UART_ESCAPE_DAT, MTK_UART_ESCAPE_CHAR); serial_out(up, MTK_UART_ESCAPE_EN, 0x00); serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); - serial_out(up, UART_EFR, serial_in(up, UART_EFR) & + serial_out(up, MTK_UART_EFR, serial_in(up, MTK_UART_EFR) & (~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK))); serial_out(up, UART_LCR, lcr); mtk8250_disable_intrs(up, MTK_UART_IER_XOFFI | @@ -255,8 +262,8 @@ static void mtk8250_set_flow_ctrl(struct uart_8250_port *up, int mode) serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); /*enable hw flow control*/ - serial_out(up, UART_EFR, MTK_UART_EFR_HW_FC | - (serial_in(up, UART_EFR) & + serial_out(up, MTK_UART_EFR, MTK_UART_EFR_HW_FC | + (serial_in(up, MTK_UART_EFR) & (~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK)))); serial_out(up, UART_LCR, lcr); @@ -270,12 +277,12 @@ static void mtk8250_set_flow_ctrl(struct uart_8250_port *up, int mode) serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); /*enable sw flow control */ - serial_out(up, UART_EFR, MTK_UART_EFR_XON1_XOFF1 | - (serial_in(up, UART_EFR) & + serial_out(up, MTK_UART_EFR, MTK_UART_EFR_XON1_XOFF1 | + (serial_in(up, MTK_UART_EFR) & (~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK)))); - serial_out(up, UART_XON1, START_CHAR(port->state->port.tty)); - serial_out(up, UART_XOFF1, STOP_CHAR(port->state->port.tty)); + serial_out(up, MTK_UART_XON1, START_CHAR(port->state->port.tty)); + serial_out(up, MTK_UART_XOFF1, STOP_CHAR(port->state->port.tty)); serial_out(up, UART_LCR, lcr); mtk8250_disable_intrs(up, MTK_UART_IER_CTSI|MTK_UART_IER_RTSI); mtk8250_enable_intrs(up, MTK_UART_IER_XOFFI); @@ -568,6 +575,10 @@ static int mtk8250_probe(struct platform_device *pdev) uart.dma = data->dma; #endif + /* Set AP UART new register map */ + writel(MTK_UART_FEAT_NEWRMAP, uart.port.membase + + (MTK_UART_FEATURE_SEL << uart.port.regshift)); + /* Disable Rate Fix function */ writel(0x0, uart.port.membase + (MTK_UART_RATE_FIX << uart.port.regshift)); |