diff options
Diffstat (limited to 'drivers/tty/serial/Kconfig')
| -rw-r--r-- | drivers/tty/serial/Kconfig | 101 |
1 files changed, 49 insertions, 52 deletions
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig index ffcf4882b25f..79a8186d3361 100644 --- a/drivers/tty/serial/Kconfig +++ b/drivers/tty/serial/Kconfig @@ -128,7 +128,7 @@ config SERIAL_SB1250_DUART_CONSOLE config SERIAL_ATMEL bool "AT91 on-chip serial port support" depends on COMMON_CLK - depends on ARCH_AT91 || COMPILE_TEST + depends on ARCH_AT91 || ARCH_LAN969X || COMPILE_TEST select SERIAL_CORE select SERIAL_MCTRL_GPIO if GPIOLIB select MFD_AT91_USART @@ -179,25 +179,6 @@ config SERIAL_ATMEL_TTYAT Say Y if you have an external 8250/16C550 UART. If unsure, say N. -config SERIAL_KGDB_NMI - bool "Serial console over KGDB NMI debugger port" - depends on KGDB_SERIAL_CONSOLE - help - This special driver allows you to temporary use NMI debugger port - as a normal console (assuming that the port is attached to KGDB). - - Unlike KDB's disable_nmi command, with this driver you are always - able to go back to the debugger using KGDB escape sequence ($3#33). - This is because this console driver processes the input in NMI - context, and thus is able to intercept the magic sequence. - - Note that since the console interprets input and uses polling - communication methods, for things like PPP you still must fully - detach debugger port from the KGDB NMI (i.e. disable_nmi), and - use raw console. - - If unsure, say N. - config SERIAL_MESON tristate "Meson serial port support" depends on ARCH_MESON || COMPILE_TEST @@ -306,12 +287,38 @@ config SERIAL_TEGRA_TCU_CONSOLE If unsure, say Y. +config SERIAL_TEGRA_UTC + tristate "NVIDIA Tegra UART Trace Controller" + depends on ARCH_TEGRA || COMPILE_TEST + select SERIAL_CORE + help + Support for Tegra UTC (UART Trace controller) client serial port. + + UTC is a HW based serial port that allows multiplexing multiple data + streams of up to 16 UTC clients into a single hardware serial port. + +config SERIAL_TEGRA_UTC_CONSOLE + bool "Support for console on a Tegra UTC serial port" + depends on SERIAL_TEGRA_UTC + select SERIAL_CORE_CONSOLE + default SERIAL_TEGRA_UTC + help + If you say Y here, it will be possible to use a Tegra UTC client as + the system console (the system console is the device which receives + all kernel messages and warnings and which allows logins in single + user mode). + + If unsure, say Y. + config SERIAL_MAX3100 - tristate "MAX3100 support" + tristate "MAX3100/3110/3111/3222 support" depends on SPI select SERIAL_CORE help - MAX3100 chip support + This selects support for an advanced UART from Maxim. + Supported ICs are MAX3100, MAX3110, MAX3111, MAX3222. + + Say Y here if you want to support these ICs. config SERIAL_MAX310X tristate "MAX310X support" @@ -874,7 +881,7 @@ config SERIAL_TXX9_STDSERIAL config SERIAL_JSM tristate "Digi International NEO and Classic PCI Support" - depends on PCI + depends on PCI && HAS_IOPORT select SERIAL_CORE help This is a driver for Digi International's Neo and Classic series @@ -1020,42 +1027,32 @@ config SERIAL_SCCNXP_CONSOLE help Support for console on SCCNXP serial ports. -config SERIAL_SC16IS7XX_CORE - tristate - config SERIAL_SC16IS7XX - tristate "SC16IS7xx serial support" + tristate "NXP SC16IS7xx UART support" + depends on SPI_MASTER || I2C select SERIAL_CORE - depends on (SPI_MASTER && !I2C) || I2C + select SERIAL_SC16IS7XX_SPI if SPI_MASTER + select SERIAL_SC16IS7XX_I2C if I2C help - This selects support for SC16IS7xx serial ports. - Supported ICs are SC16IS740, SC16IS741, SC16IS750, SC16IS752, - SC16IS760 and SC16IS762. Select supported buses using options below. + Core driver for NXP SC16IS7xx UARTs. + Supported ICs are: + + SC16IS740 + SC16IS741 + SC16IS750 + SC16IS752 + SC16IS760 + SC16IS762 + + The driver supports both I2C and SPI interfaces. config SERIAL_SC16IS7XX_I2C - bool "SC16IS7xx for I2C interface" - depends on SERIAL_SC16IS7XX - depends on I2C - select SERIAL_SC16IS7XX_CORE if SERIAL_SC16IS7XX - select REGMAP_I2C if I2C - default y - help - Enable SC16IS7xx driver on I2C bus, - If required say y, and say n to i2c if not required, - Enabled by default to support oldconfig. - You must select at least one bus for the driver to be built. + tristate + select REGMAP_I2C config SERIAL_SC16IS7XX_SPI - bool "SC16IS7xx for spi interface" - depends on SERIAL_SC16IS7XX - depends on SPI_MASTER - select SERIAL_SC16IS7XX_CORE if SERIAL_SC16IS7XX - select REGMAP_SPI if SPI_MASTER - help - Enable SC16IS7xx driver on SPI bus, - If required say y, and say n to spi if not required, - This is additional support to existing driver. - You must select at least one bus for the driver to be built. + tristate + select REGMAP_SPI config SERIAL_TIMBERDALE tristate "Support for timberdale UART" |