| Age | Commit message (Collapse) | Author |
|---|
|
Dequeue retry timeout controls the interval between checks for unmet
conditions. On MI series, reduce this from 0x40 to 0x1 (~ 1 uS). The
cost of additional bandwidth consumed by CP when polling memory
shouldn't be substantial.
Signed-off-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Reviewed-by: Jonathan Kim <jonathan.kim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
To reset hung SDMA queues on GFX 9.4+ for the GFX9 family, a soft reset
must be issued through SMU. Since soft resets will reset an entire SDMA
engine, use a common KGD call to do the reset as the KGD will handle
avoiding a reset of in flight GFX and paging queues on that engine.
In addition, create a common call for all reset types to simplify
the handling of module parameter settings that block gpu resets.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Harish Kasiviswanathan <harish.kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Support per-queue reset for GFX9. The recommendation is for the driver
to target reset the HW queue via a SPI MMIO register write.
Since this requires pipe and HW queue info and MEC FW is limited to
doorbell reports of hung queues after an unmap failure, scan the HW
queue slots defined by SET_RESOURCES first to identify the user queue
candidates to reset.
Only signal reset events to processes that have had a queue reset.
If queue reset fails, fall back to GPU reset.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This patch fixes the case where the code currently passes
absolute register address and not the reg offset, which HWS
expects, when sending the PM4 packet to set/update CWSR grace
period. Additionally, cleanup the signature of
build_grace_period_packet_info function as it no longer needs
the inst parameter.
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Reviewed-by: Jonathan Kim <jonathan.kim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Implement the similarities as GC v9.4.2, and the difference
for GC v9.4.3 HW spec, i.e. xcc instance.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Signed-off-by: Eric Huang <jinhuieric.huang@amd.com>
Reviewed-by: Jonathan Kim <jonathan.kim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Shader read, write and atomic memory operations can be alerted to the
debugger as an address watch exception.
Allow the debugger to pass in a watch point to a particular memory
address per device.
Note that there exists only 4 watch points per devices to date, so have
the KFD keep track of what watch points are allocated or not.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Allow the debugger to set wave behaviour on to either normally operate,
halt at launch, trap on every instruction, terminate immediately or
stall on allocation.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This operation allows the debugger to override the enabled HW
exceptions on the device.
On debug devices that only support the debugging of a single process,
the HW exceptions are global and set through the SPI_GDBG_TRAP_MASK
register.
Because they are global, only address watch exceptions are allowed to
be enabled. In other words, the debugger must preserve all non-address
watch exception states in normal mode operation by barring a full
replacement override or a non-address watch override request.
For multi-process debugging, all HW exception overrides are per-VMID so
all exceptions can be overridden or fully replaced.
In order for the debugger to know what is permissible, returned the
supported override mask back to the debugger along with the previously
enable overrides.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The HWS schedule allows a grace period for wave completion prior to
preemption for better performance by avoiding CWSR on waves that can
potentially complete quickly. The debugger, on the other hand, will
want to inspect wave status immediately after it actively triggers
preemption (a suspend function to be provided).
To minimize latency between preemption and debugger wave inspection, allow
immediate preemption by setting the grace period to 0.
Note that setting the preepmtion grace period to 0 will result in an
infinite grace period being set due to a CP FW bug so set it to 1 for now.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Similar to GFX9 debug devices, set the hardware debug mode by draining
the SPI appropriately prior the mode setting request.
Because GFX10 has waves allocated by the work group boundary and each
SE's SPI instances do not communicate, the SPI drain time is much longer.
This long drain time will be fixed for GFX11 onwards.
Also remove a bunch of deprecated misplaced references for GFX10.3.
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
