| Age | Commit message (Collapse) | Author |
|---|
|
Enable the VSYNC Rising Edge Detection interrupt and generate a
FRAME_SYNC event form it. The interrupt is available on all supported
models of the VIN (Gen2, Gen3 and Gen4).
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20250616185722.980722-4-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Depending on if the capture session deals with fields or whole frames
interrupts can be generated at an end of field, or end of frame event.
The interrupt mask is setup to generate an interrupt on one of the two
events depending on what is needed when the VIN is started. The end of
field bit is set in both cases so controlling the mask that generates an
interrupt have been enough to control the two use-cases.
Before extending the interrupt handler to deal with other types of
interrupt events it is needs to extended to "capture complete" check for
correct the use-case in operation. Without this the simplification in
the handler can result in corrupted frames when the mask on what type of
events can generate an interrupt generated can no longer be assumed to
only be an "capture complete" event.
Which bit is checked matches which bit is enabled at configuration time
as which event can generate an interrupt for "capture complete". There
is no functional change.
While at it switch to use the BIT() macro to describe the bit positions
for the interrupt functions.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20250616185722.980722-3-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
The call sites using the interrupt helper functions have all been
reworked to only one for each. Fold each of them into the only call
sites left.
This fixes a possible interrupt loss in case an interrupt occurs between
reading VNINTS_REG in rvin_get_interrupt_status() and reading it again
in rvin_ack_interrupt().
While at it rename the variable holding the current interrupt status to
make the code easier to read.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20250616185722.980722-2-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
With Gen2 converted to use the common media device there is only one
caller left for the helper to notify a video device of an event, fold it
in.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20250613153434.2001800-14-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Complete the conversion from soc_camera to a full fledge media
controller enabled devices for all supported generations of the device.
All work is already done as this is already supported on Gen3, and
later.
All that is missing is removing all special cases for the non
media-graph call paths and use the common ones in their place.
The one change that stands out is dropping the doubling of the height in
the Gen2 scaler setup, rvin_scaler_gen2(). In the Gen2 non-MC world the
VIN size was set to match the video source subdevices, and if that was a
TOP/BOTTOM video source it needed to be doubled for the scaler to
function properly. In the MC world this is now handled by user-space
configuration of the pipeline and the adjustment is not needed.
Mark the completion of converting from soc_camera by injecting an
attribution of myself in the header.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20250613153434.2001800-13-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Before moving Gen2 to media controller simplify the creation of controls
by not exposing the sub-device controls on the video device. This could
be done while enabling media controller but doing it separately reduces
the changes needed to do so.
The rework also allows the cleanup and remove paths to be simplified by
folding all special cases into the only remaining call site.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20250613153434.2001800-12-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
On Gen2 where sub-devices where not exposed to user-space the field
TB/BT ordering was controlled by a hack in the VIN driver. Before
converting it to media device model where the subdevice is exposed
remove that hack.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20250613153434.2001800-11-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Prepare for Gen2 media graph support by always initializing a media pad
for the VIN device.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20250613153434.2001800-10-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
The VIN usage of v4l-async is complex and stems from organic growth of
the driver of supporting both private local subdevices (Gen2, Gen3) and
subdevices shared between all VIN instances (Gen3 and Gen4).
The driver used a separate notifier for each VIN for the private local
ones, and a shared group notifier for the shared ones. This was complex
and lead to subtle bugs when unbinding and later rebinding subdevices in
one of the notifiers having to handle different edge cases depending on
if it also had subdevices in the other notifiers etc.
To simplify this have the Gen2 devices allocate and form a VIN group
too. This way all subdevices on all models can be collect in a
single group notifier. Then there is only a single complete callback for
all where the video devices and subdevice nodes can be registered etc.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20250613153434.2001800-9-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Use the __free(fwnode_handle) hooks to free the endpoints when the
function exits to simplify the error paths and make the intent more
clear.
While at it correct the error message when failing to parse an endpoint
to report the correct node.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20250613153434.2001800-8-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
The R-Car VIN driver is needlessly complex and uses more then one
v4l-async notifier to attach to all its subdevices. Prepare for unifying
them by moving rvin_parallel_parse_of() to where it needs to be when
they are unified.
The function is moved verbatim and there is no change in behavior.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20250613153434.2001800-7-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Prepare to move Gen2 and earlier models to media controller by
generating a unique VIN group id for each VIN instance. On Gen3 and Gen4
it is important to have a specific id in the group as media graph routes
depend on this. On Gen2 and earlier models all that will matter is to
have a unique id in the range.
Break out the id generation to a own function keeping the logic for Gen3
and Gen4 while generating a sequential id for Gen2 models.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20250613153434.2001800-6-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Prepare for more failed probe conditions that needs cleanup by
converting the error path to use labels.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20250613153434.2001800-5-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
The link setup callback once acted on each VIN instance, and expected to
be called once for each VIN instance. This have changed as the driver
grew support for later hardware generations and the callback is now
expected to setup links for all VIN in the group.
The argument to the callback has however remained a pointer to a single
VIN instance. This pointer was then used to get the group structure. Fix
this and pass the group as the single argument to the link setup
callback making the expectation of the function clear.
There is no intentional change in behavior.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20250613153434.2001800-4-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
When the transition of Gen2 to use groups are complete the platform
specific information can be retrieved from the group instead of being
duplicated in each VIN's private data structure.
Prepare for this by already adding the information to the group
structure so it can be used without first having to find the group from
a VIN instances private data.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20250613153434.2001800-3-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
When extending the driver with Gen4 support the iteration of over
possible remote subdevices changed from being R-Car CSI-2 Rx only to
also cover R-Car CSISP instances. In two loops updating the bounds
variable was missed.
This had no ill effect as the count the two values have always been the
same in the past. Fix it by looking at the array size.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20250613153434.2001800-2-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Fix the following to get RAW10 formats working:
In rvin_formats, the bpp is set to 4 for RAW10. As VIN unpacks RAW10 to
16-bit containers, the bpp should be 2.
Don't set VNDMR_YC_THR to the VNDMR register. The YC_THR is "YC Data
Through Mode", used for YUV formats and should not be set for RAW10.
Fixes: 1b7e7240eaf3 ("media: rcar-vin: Add support for RAW10")
Cc: stable@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20250424-rcar-fix-raw-v2-4-f6afca378124@ideasonboard.com
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
On Gen4 we need to set VNMC's EXINF to a different value (1) than in
Gen3 (0). Add a define for this, and set the bit for Gen4.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20250424-rcar-fix-raw-v2-3-f6afca378124@ideasonboard.com
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Remove unnecessary checks wrt. formats and interfaces in rvin_setup().
The validity of the formats has already been checked earlier.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20250424-rcar-fix-raw-v2-2-f6afca378124@ideasonboard.com
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Currently Gen4 VINs are marked as RCAN_GEN3 models. Add a new enum
value, RCAR_GEN4, and use it for Gen4 VINs. No functional changes in
this patch.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20250424-rcar-fix-raw-v2-1-f6afca378124@ideasonboard.com
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Standardize reporting of rectangles to (t,l)/wxh.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
When shutting down capture extra care was needed to try and complete a
buffer that was involved in the emulated support for SEQ_{TB,BT}. This
was needed as a buffer might be queued once to the driver, but two times
to the hardware using different offsets.
As support for SEQ_{TB,BT} is now removed this shutdown process can be
greatly simplified. And in addition the state keeping of the VIN device
can be reduced to a single boolean value instead of keeping track of
this SEQ_{TB,BT} stopping dance.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
The STARTING state is superfluous and can be replaced with a check of
the sequence counter. The design idea is that the first buffer returned
from the driver have to come from the first hardware buffer slot.
Failing this the first 3 buffers queued to the device can be returned
out-of-order.
But it's much clearer to check the sequence counter to only return the
first buffer if it comes from hardware slot 0 then it is to carry around
an extra state just for this. Remove the unneeded state and replace it
with a simpler check.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
The VIN state of suspended is superfluous. The logic was that when the
device were suspended and in a RUNNING state the state was set to
SUSPENDED. And when resuming it checked if the state is SUSPENDED and if
so started the device and changed it to RUNNING.
This can be avoided by simply checking if the device is in a RUNNING
state at both suspend and resume callbacks. Remove the unneeded
complexity.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
When the driver was converted from soc_camera software support for
V4L2_FIELD_SEQ_TB and V4L2_FIELD_SEQ_BT were added. This was done by
capturing twice to the same VB2 buffer, but at different offsets.
This turned out to be a bad idea and it never really worked properly in
all situations. As the hardware can't support this mode natively remove
trying to emulate it in software. It's still possible to capture TOP or
BOTTOM fields separately or both ALTERNATING. If user-space wants the
same fields in the same buffer the same hack to capture twice to the
same buffer can be done.
Removing this error prone emulated support pave ways in future work to
simplify the internal buffer handling and making it less fragile, while
enabling adding support for other features the hardware actually
supports.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Earlier versions of the datasheet where unclear about the stride setting
for RAW8 capture formats. Later datasheets clarifies that the stride
only process in this mode for non-image data. For image data the full
stride shall be used. Compare section "RAW: 8 Bits and Embedded 8-Bit
Non-Image Data, User Defined 8-bit Data" vs "RAW: 8 Bits".
Remove the special case from pixel formats that carry image data and
treat it as any other image format.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20250402183302.140055-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Use v4l2_subdev_{enable|disable}_streams() instead of calling s_stream
op directly. This allows the called subdev to drop the legacy s_stream
op.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Since commit 88785982a19d ("media: vb2: use lock if wait_prepare/finish
are NULL") it is no longer needed to set the wait_prepare/finish
vb2_ops callbacks as long as the lock field in vb2_queue is set.
Since the vb2_ops_wait_prepare/finish callbacks already rely on that field,
we can safely drop these callbacks.
This simplifies the code and this is a step towards the goal of deleting
these callbacks.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> # for meson-ge2d
Acked-by: Andrzej Pietrasiewicz <andrzejtp2010@gmail.com>
|
|
Some R-Car SoCs are capable of capturing RAW10. Extend the format
enumeration, validation and setup to expose and configure for this
format if the particular device supports it.
The VIN is usually capable of converting from most media bus formats to
a range of different pixel formats. However if the input media bus
format is a RAW10 format this is not possible so the corresponding pixel
output format is forced.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/media to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Add the Gen4 family compatible. This will be used instead of a SoC
specific compatible for the new Gen4 SoC V4M. Two Gen4 boards (V3U and
V4H) have already been added prior and their bindings need to be kept
for backward compatibility.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20240704161620.1425409-5-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The YUYV8_1X16 and UYVY8_1X16 formats are treated as 'ITU-R
BT.601/BT.1358 16-bit YCbCr-422 input' (YUV16 - 0x5) in the R-Car VIN
driver and are thus disallowed when capturing frames from the R-Car
CSI-2 interface according to the hardware manual.
As the 1X16 format variants are meant to be used with serial busses they
have to be treated as 'YCbCr-422 8-bit data input' (0x1) when capturing
from CSI-2, which is a valid setting for CSI-2.
Commit 78b3f9d75a62 ("media: rcar-vin: Add check that input interface
and format are valid") disallowed capturing YUV16 when using the CSI-2
interface. Fix this by using YUV8_BT601 for YCbCr422 when CSI-2 is in
use.
Fixes: 78b3f9d75a62 ("media: rcar-vin: Add check that input interface and format are valid")
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20240617161135.130719-2-jacopo.mondi@ideasonboard.com
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
Use the pad variant for all (s|g|query)_dv_timings subdev calls, which
includes a pad argument.
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
clang-19 warns about mixing two enum types here:
drivers/media/platform/renesas/rcar-vin/rcar-vin.h:296:12: error: conditional expression between different enumeration types ('enum rvin_csi_id' and 'enum rvin_isp_id') [-Werror,-Wenum-compare-conditional]
drivers/media/platform/renesas/rcar-vin/rcar-core.c:216:18: error: conditional expression between different enumeration types ('enum rvin_csi_id' and 'enum rvin_isp_id') [-Werror,-Wenum-compare-conditional]
drivers/media/platform/renesas/rcar-vin/rcar-vin.h:296:12: error: conditional expression between different enumeration types ('enum rvin_csi_id' and 'enum rvin_isp_id') [-Werror,-Wenum-compare-conditional]
drivers/media/platform/renesas/rcar-vin/rcar-vin.h:296:12: error: conditional expression between different enumeration types ('enum rvin_csi_id' and 'enum rvin_isp_id') [-Werror,-Wenum-compare-conditional]
This one is intentional, and there is already a cast to work around another
warning, so address this by adding another cast.
Fixes: 406bb586dec0 ("media: rcar-vin: Add r8a779a0 support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The rcar-csi2 driver was added before the platform/renesas directory
existed and since it was used together in a pipeline with the rcar-vin
driver it was located together with it.
The rcar-isp driver can also be used together with the rcar-csi2 driver
in a pipeline that is terminated by the rcar-vin driver. However by the
time rcar-isp was added the platform/renesas directory existed so it was
added there.
To remove the confusion that the rcar-csi2 driver have code dependencies
on the rcar-vin driver move it to the same directory level as the
rcar-isp driver. This makes it clear they are three distinct drivers
that can be used together in a pipeline, but do not depend on each
other.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Rename min_buffers_needed into min_queued_buffers and update
the documentation about it.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: Drop the change where min_queued_buffers + 1 buffers would be]
[hverkuil: allocated. Now this patch only renames this field instead of making]
[hverkuil: a functional change as well.]
[hverkuil: Renamed 3 remaining min_buffers_needed occurrences.]
|
|
Switch all drivers accessing sub-device state to use the stream-aware
functions. We will soon remove the old ones.
This patch has been generated using the following Coccinelle script:
---------8<------------
@@
expression E1, E2, E3;
@@
- v4l2_subdev_get_pad_format(E1, E2, E3)
+ v4l2_subdev_state_get_format(E2, E3)
@@
expression E1, E2, E3;
@@
- v4l2_subdev_get_pad_crop(E1, E2, E3)
+ v4l2_subdev_state_get_crop(E2, E3)
@@
expression E1, E2, E3;
@@
- v4l2_subdev_get_pad_compose(E1, E2, E3)
+ v4l2_subdev_state_get_compose(E2, E3)
@@
expression E1, E2, E3;
@@
- v4l2_subdev_get_try_format(E1, E2, E3)
+ v4l2_subdev_state_get_format(E2, E3)
@@
expression E1, E2, E3;
@@
- v4l2_subdev_get_try_crop(E1, E2, E3)
+ v4l2_subdev_state_get_crop(E2, E3)
@@
expression E1, E2, E3;
@@
- v4l2_subdev_get_try_compose(E1, E2, E3)
+ v4l2_subdev_state_get_compose(E2, E3)
---------8<------------
Additionally drivers/media/i2c/s5k5baf.c and
drivers/media/platform/samsung/s3c-camif/camif-capture.c have been
manually changed as Coccinelle didn't. Further local variables have been
removed as they became unused as a result of the other changes.
Also Coccinelle introduced indentation by space in files
drivers/media/i2c/st-mipid02.c and
drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c. This has been also
corrected.
The diff from Coccinelle-generated changes are:
> diff --git b/drivers/media/i2c/imx319.c a/drivers/media/i2c/imx319.c
> index e549692ff478..420984382173 100644
> --- b/drivers/media/i2c/imx319.c
> +++ a/drivers/media/i2c/imx319.c
> @@ -2001,7 +2001,6 @@ static int imx319_do_get_pad_format(struct imx319 *imx319,
> struct v4l2_subdev_format *fmt)
> {
> struct v4l2_mbus_framefmt *framefmt;
> - struct v4l2_subdev *sd = &imx319->sd;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> diff --git b/drivers/media/i2c/imx355.c a/drivers/media/i2c/imx355.c
> index 96bdde685d65..e1b1d2fc79dd 100644
> --- b/drivers/media/i2c/imx355.c
> +++ a/drivers/media/i2c/imx355.c
> @@ -1299,7 +1299,6 @@ static int imx355_do_get_pad_format(struct imx355 *imx355,
> struct v4l2_subdev_format *fmt)
> {
> struct v4l2_mbus_framefmt *framefmt;
> - struct v4l2_subdev *sd = &imx355->sd;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> diff --git b/drivers/media/i2c/ov08x40.c a/drivers/media/i2c/ov08x40.c
> index ca799bbcfdb7..abbb0b774d43 100644
> --- b/drivers/media/i2c/ov08x40.c
> +++ a/drivers/media/i2c/ov08x40.c
> @@ -2774,7 +2774,6 @@ static int ov08x40_do_get_pad_format(struct ov08x40 *ov08x,
> struct v4l2_subdev_format *fmt)
> {
> struct v4l2_mbus_framefmt *framefmt;
> - struct v4l2_subdev *sd = &ov08x->sd;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> diff --git b/drivers/media/i2c/ov13858.c a/drivers/media/i2c/ov13858.c
> index 7816d9787c61..09387e335d80 100644
> --- b/drivers/media/i2c/ov13858.c
> +++ a/drivers/media/i2c/ov13858.c
> @@ -1316,7 +1316,6 @@ static int ov13858_do_get_pad_format(struct ov13858 *ov13858,
> struct v4l2_subdev_format *fmt)
> {
> struct v4l2_mbus_framefmt *framefmt;
> - struct v4l2_subdev *sd = &ov13858->sd;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> diff --git b/drivers/media/i2c/ov13b10.c a/drivers/media/i2c/ov13b10.c
> index 268cd4b03f9c..c06411d5ee2b 100644
> --- b/drivers/media/i2c/ov13b10.c
> +++ a/drivers/media/i2c/ov13b10.c
> @@ -1001,7 +1001,6 @@ static int ov13b10_do_get_pad_format(struct ov13b10 *ov13b,
> struct v4l2_subdev_format *fmt)
> {
> struct v4l2_mbus_framefmt *framefmt;
> - struct v4l2_subdev *sd = &ov13b->sd;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> framefmt = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> diff --git b/drivers/media/i2c/s5c73m3/s5c73m3-core.c a/drivers/media/i2c/s5c73m3/s5c73m3-core.c
> index 47605e36bc60..8f9b5713daf7 100644
> --- b/drivers/media/i2c/s5c73m3/s5c73m3-core.c
> +++ a/drivers/media/i2c/s5c73m3/s5c73m3-core.c
> @@ -819,7 +819,6 @@ static void s5c73m3_oif_try_format(struct s5c73m3 *state,
> struct v4l2_subdev_format *fmt,
> const struct s5c73m3_frame_size **fs)
> {
> - struct v4l2_subdev *sd = &state->sensor_sd;
> u32 code;
>
> switch (fmt->pad) {
> diff --git a/drivers/media/i2c/s5k5baf.c b/drivers/media/i2c/s5k5baf.c
> index 67da2045f543..03ccfb0e1e11 100644
> --- a/drivers/media/i2c/s5k5baf.c
> +++ b/drivers/media/i2c/s5k5baf.c
> @@ -1472,14 +1472,11 @@ static int s5k5baf_set_selection(struct v4l2_subdev *sd,
>
> if (sel->which == V4L2_SUBDEV_FORMAT_TRY) {
> rects = (struct v4l2_rect * []) {
> - &s5k5baf_cis_rect,
> - v4l2_subdev_get_try_crop(sd, sd_state,
> - PAD_CIS),
> - v4l2_subdev_get_try_compose(sd, sd_state,
> - PAD_CIS),
> - v4l2_subdev_get_try_crop(sd, sd_state,
> - PAD_OUT)
> - };
> + &s5k5baf_cis_rect,
> + v4l2_subdev_state_get_crop(sd_state, PAD_CIS),
> + v4l2_subdev_state_get_compose(sd_state, PAD_CIS),
> + v4l2_subdev_state_get_crop(sd_state, PAD_OUT)
> + };
> s5k5baf_set_rect_and_adjust(rects, rtype, &sel->r);
> return 0;
> }
> diff --git b/drivers/media/platform/samsung/s3c-camif/camif-capture.c a/drivers/media/platform/samsung/s3c-camif/camif-capture.c
> index 295e083f38e8..be58260ea67e 100644
> --- b/drivers/media/platform/samsung/s3c-camif/camif-capture.c
> +++ a/drivers/media/platform/samsung/s3c-camif/camif-capture.c
> @@ -1216,7 +1216,7 @@ static int s3c_camif_subdev_get_fmt(struct v4l2_subdev *sd,
> struct v4l2_mbus_framefmt *mf = &fmt->format;
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> - mf = v4l2_subdev_get_try_format(sd, sd_state, fmt->pad);
> + mf = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> fmt->format = *mf;
> return 0;
> }
> @@ -1305,7 +1305,7 @@ static int s3c_camif_subdev_set_fmt(struct v4l2_subdev *sd,
> __camif_subdev_try_format(camif, mf, fmt->pad);
>
> if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
> - mf = v4l2_subdev_get_try_format(sd, sd_state, fmt->pad);
> + mf = v4l2_subdev_state_get_format(sd_state, fmt->pad);
> *mf = fmt->format;
> mutex_unlock(&camif->lock);
> return 0;
> diff --git b/drivers/media/platform/ti/cal/cal-camerarx.c a/drivers/media/platform/ti/cal/cal-camerarx.c
> index cea454ed9c20..61433744c6c4 100644
> --- b/drivers/media/platform/ti/cal/cal-camerarx.c
> +++ a/drivers/media/platform/ti/cal/cal-camerarx.c
> @@ -621,8 +621,6 @@ static int cal_camerarx_sd_enum_mbus_code(struct v4l2_subdev *sd,
> struct v4l2_subdev_state *state,
> struct v4l2_subdev_mbus_code_enum *code)
> {
> - struct cal_camerarx *phy = to_cal_camerarx(sd);
> -
> /* No transcoding, source and sink codes must match. */
> if (cal_rx_pad_is_source(code->pad)) {
> struct v4l2_mbus_framefmt *fmt;
> diff --git b/drivers/staging/media/imx/imx-ic-prp.c a/drivers/staging/media/imx/imx-ic-prp.c
> index dd558fac6477..61d69f19657e 100644
> --- b/drivers/staging/media/imx/imx-ic-prp.c
> +++ a/drivers/staging/media/imx/imx-ic-prp.c
> @@ -82,8 +82,6 @@ static struct v4l2_mbus_framefmt *
> __prp_get_fmt(struct prp_priv *priv, struct v4l2_subdev_state *sd_state,
> unsigned int pad, enum v4l2_subdev_format_whence which)
> {
> - struct imx_ic_priv *ic_priv = priv->ic_priv;
> -
> if (which == V4L2_SUBDEV_FORMAT_TRY)
> return v4l2_subdev_state_get_format(sd_state, pad);
> else
> diff --git b/drivers/staging/media/imx/imx-ic-prpencvf.c a/drivers/staging/media/imx/imx-ic-prpencvf.c
> index 02db7dbb884b..ec73c901079e 100644
> --- b/drivers/staging/media/imx/imx-ic-prpencvf.c
> +++ a/drivers/staging/media/imx/imx-ic-prpencvf.c
> @@ -790,8 +790,6 @@ static struct v4l2_mbus_framefmt *
> __prp_get_fmt(struct prp_priv *priv, struct v4l2_subdev_state *sd_state,
> unsigned int pad, enum v4l2_subdev_format_whence which)
> {
> - struct imx_ic_priv *ic_priv = priv->ic_priv;
> -
> if (which == V4L2_SUBDEV_FORMAT_TRY)
> return v4l2_subdev_state_get_format(sd_state, pad);
> else
> diff --git a/drivers/media/i2c/st-mipid02.c b/drivers/media/i2c/st-mipid02.c
> index 9c9361354c00..b08a249b5fdd 100644
> --- a/drivers/media/i2c/st-mipid02.c
> +++ b/drivers/media/i2c/st-mipid02.c
> @@ -751,7 +751,7 @@ static void mipid02_set_fmt_source(struct v4l2_subdev *sd,
> format->format = bridge->fmt;
> else
> format->format = *v4l2_subdev_state_get_format(sd_state,
> - MIPID02_SINK_0);
> + MIPID02_SINK_0);
>
> /* but code may need to be converted */
> format->format.code = serial_to_parallel_code(format->format.code);
> diff --git a/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c b/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c
> index 117912d3bfbd..96353648c032 100644
> --- a/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c
> +++ b/drivers/media/platform/rockchip/rkisp1/rkisp1-isp.c
> @@ -319,7 +319,7 @@ static void rkisp1_isp_start(struct rkisp1_isp *isp,
> rkisp1_write(rkisp1, RKISP1_CIF_ISP_CTRL, val);
>
> src_fmt = v4l2_subdev_state_get_format(sd_state,
> - RKISP1_ISP_PAD_SOURCE_VIDEO);
> + RKISP1_ISP_PAD_SOURCE_VIDEO);
> src_info = rkisp1_mbus_info_get_by_code(src_fmt->code);
>
> if (src_info->pixel_enc != V4L2_PIXEL_ENC_BAYER)
> @@ -475,9 +475,9 @@ static void rkisp1_isp_set_src_fmt(struct rkisp1_isp *isp,
> sink_fmt = v4l2_subdev_state_get_format(sd_state,
> RKISP1_ISP_PAD_SINK_VIDEO);
> src_fmt = v4l2_subdev_state_get_format(sd_state,
> - RKISP1_ISP_PAD_SOURCE_VIDEO);
> + RKISP1_ISP_PAD_SOURCE_VIDEO);
> src_crop = v4l2_subdev_state_get_crop(sd_state,
> - RKISP1_ISP_PAD_SOURCE_VIDEO);
> + RKISP1_ISP_PAD_SOURCE_VIDEO);
>
> /*
> * Media bus code. The ISP can operate in pass-through mode (Bayer in,
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Don't rely on a define, let the compiler use the actual
field size.
Remove all uses of the V4L2_SUBDEV_NAME_SIZE define and also
drop the define itself.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@ragnatech.se>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
|
|
Add support for C-PHY on R-Car V4H. While the V4H supports both D-PHY
and C-PHY this patch only adds support for the C-PHY mode due to lack of
documentation and hardware to test on.
The V4H is the first Gen4 device that is enabled in the rcar-csi2
driver. There is much overlap with the Gen3 driver, the primary
difference is in how the receiver is started. The V4H have a much larger
register space and some addresses overlap with Gen3.
[Sakari Ailus: Use div_u64() to divide a 64-bit integer.]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Set the v4l2_device already in async notifier init, so struct device
related to it will be available before the notifier is registered. This
requires separating notifier initialisation into two functions, one that
takes v4l2_device as its argument, v4l2_async_nf_init and
v4l2_async_subdev_nf_init, for sub-device notifiers. Registering the
notifier will use a single function, v4l2_async_nf_register.
This is done in order to make struct device available earlier, during
construction of the async connections, for sensible debug prints.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de> # imx6qp
Tested-by: Niklas Söderlund <niklas.soderlund@ragnatech.se> # rcar + adv746x
Tested-by: Aishwarya Kothari <aishwarya.kothari@toradex.com> # Apalis i.MX6Q with TC358743
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> # Renesas RZ/G2L SMARC
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
This patch re-arranges internal V4L2 async lists for preparation of
supporting multiple connections per sub-device as well as cleaning up used
lists.
The list of unbound V4L2 sub-devices shall be maintained for the purpose of
listing those sub-devices only, not for their bindin status. Also, the V4L2
async connections now have, instead of two list entries, a single list
entry in the notifier's list, be that either waiting or done lists, while
the notifier's asc_list is removed.
The one-to-one relation between a sub-device and a connection is still
maintained in this patch.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de> # imx6qp
Tested-by: Niklas Söderlund <niklas.soderlund@ragnatech.se> # rcar + adv746x
Tested-by: Aishwarya Kothari <aishwarya.kothari@toradex.com> # Apalis i.MX6Q with TC358743
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> # Renesas RZ/G2L SMARC
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Rename v4l2_async_subdev as v4l2_async_connection, in order to
differentiate between the sub-devices and their connections: one
sub-device can have many connections but the V4L2 async framework has so
far allowed just a single one. Connections in this context will later
translate into either MC ancillary or data links.
This patch prepares changing that relation by changing existing users of
v4l2_async_subdev to switch to v4l2_async_connection. Async sub-devices
themselves will not be needed anymore
Additionally, __v4l2_async_nf_add_subdev() has been renamed
__v4l2_async_nf_add_connection().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de> # imx6qp
Tested-by: Niklas Söderlund <niklas.soderlund@ragnatech.se> # rcar + adv746x
Tested-by: Aishwarya Kothari <aishwarya.kothari@toradex.com> # Apalis i.MX6Q with TC358743
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> # Renesas RZ/G2L SMARC
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Add support for R-Car V4H. The V4H uses the ISP Channel Selector as its
only possible video input source. Even tho V4H is a Gen3 board the VIN
interface is very close to the one found on the V3U, for this reason
mark it as a Gen3 model internally.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Gen4 will support both D-PHY and C-PHY, while Gen3 only supports D-PHY.
Add two flags to the device information structure to be able to record
what each SoC supports.
Extend the device node parsing to accept both CSI_2 D-PHY and C-PHY
buses, while at the same time taking the SoC support into account.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
[Sakari Ailus: Line wrap.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Prepare the driver for supporting R-Car Gen4. The starting of the
receiver and how to enter standby differs between Gen3 and Gen4,
create function pointers in the device info structure to control the
different behavior.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
When adding proper support for V4L2_FIELD_ALTERNATE it was missed that
this field format should trigger an interrupt for each field, not just
for the whole frame. Fix this by marking it as progressive in the
capture setup, which will then select the correct interrupt mode.
Tested on both Gen2 and Gen3 with the result of a doubling of the frame
rate for V4L2_FIELD_ALTERNATE. From a PAL video source the frame rate is
now 50, which is expected for alternate field capture.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
When doing format validation for NV12 the width and height should be
aligned to 32 pixels.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The VIN modules on Gen3 can not scale NV12, fail format validation if
the user tries. Currently no frames are produced if this is attempted.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
R-Car H3 ES1.* was only available to an internal development group and
needed a lot of quirks and workarounds. These become a maintenance
burden now, so our development group decided to remove upstream support
and disable booting for this SoC. Public users only have ES2 onwards.
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
