| Age | Commit message (Collapse) | Author |
|---|
|
Restrict the 100Mbit forced-mode workaround to link-down transitions
only, to prevent repeated link reset cycles in certain configurations.
The workaround was originally introduced to improve signal reliability
when switching cables between long and short distances. It temporarily
forces the PHY into 10 Mbps before returning to 100 Mbps.
However, when used with autonegotiating link partners (e.g., Intel i350),
executing this workaround on every link change can confuse the partner
and cause constant renegotiation loops. This results in repeated link
down/up transitions and the PHY never reaching a stable state.
Limit the workaround to only run during the PHY_NOLINK state. This ensures
it is triggered only once per link drop, avoiding disruptive toggling
while still preserving its intended effect.
Note: I am not able to reproduce the original issue that this workaround
addresses. I can only confirm that 100 Mbit mode works correctly in my
test setup. Based on code inspection, I assume the workaround aims to
reset some internal state machine or signal block by toggling speeds.
However, a PHY reset is already performed earlier in the function via
phy_init_hw(), which may achieve a similar effect. Without a reproducer,
I conservatively keep the workaround but restrict its conditions.
Fixes: e57cf3639c32 ("net: lan78xx: fix accessing the LAN7800's internal phy specific registers from the MAC driver")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250709130753.3994461-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Enable .soft_reset for the LAN88xx PHY driver by assigning
genphy_soft_reset() to ensure that the phylib core performs a proper
soft reset during reconfiguration.
Previously, the driver left .soft_reset unimplemented, so calls to
phy_init_hw() (e.g., from lan88xx_link_change_notify()) did not fully
reset the PHY. As a result, stale contents in the Link Partner Ability
(LPA) register could persist, causing the PHY to incorrectly report
that the link partner advertised autonegotiation even when it did not.
Using genphy_soft_reset() guarantees a clean reset of the PHY and
corrects the false autoneg reporting in these scenarios.
Fixes: ccb989e4d1ef ("net: phy: microchip: Reset LAN88xx PHY to ensure clean link state on LAN7800/7850")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250709130753.3994461-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Force a fixed MDI-X mode when auto-negotiation is disabled to prevent
link instability.
When forcing the link speed and duplex on a LAN9500 PHY (e.g., with
`ethtool -s eth0 autoneg off ...`) while leaving MDI-X control in auto
mode, the PHY fails to establish a stable link. This occurs because the
PHY's Auto-MDIX algorithm is not designed to operate when
auto-negotiation is disabled. In this state, the PHY continuously
toggles the TX/RX signal pairs, which prevents the link partner from
synchronizing.
This patch resolves the issue by detecting when auto-negotiation is
disabled. If the MDI-X control mode is set to 'auto', the driver now
forces a specific, stable mode (ETH_TP_MDI) to prevent the pair
toggling. This choice of a fixed MDI mode mirrors the behavior the
hardware would exhibit if the AUTOMDIX_EN strap were configured for a
fixed MDI connection.
Fixes: 05b35e7eb9a1 ("smsc95xx: add phylib support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andre Edich <andre.edich@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250703114941.3243890-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Override the hardware strap configuration for MDI-X mode to ensure a
predictable initial state for the driver. The initial mode of the LAN87xx
PHY is determined by the AUTOMDIX_EN strap pin, but the driver has no
documented way to read its latched status.
This unpredictability means the driver cannot know if the PHY has
initialized with Auto-MDIX enabled or disabled, preventing it from
providing a reliable interface to the user.
This patch introduces a `config_init` hook that forces the PHY into a
known state by explicitly enabling Auto-MDIX.
Fixes: 05b35e7eb9a1 ("smsc95xx: add phylib support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andre Edich <andre.edich@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250703114941.3243890-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Correct the Auto-MDIX configuration to ensure userspace settings are
respected when the feature is disabled by the AUTOMDIX_EN hardware strap.
The LAN9500 PHY allows its default MDI-X mode to be configured via a
hardware strap. If this strap sets the default to "MDI-X off", the
driver was previously unable to enable Auto-MDIX from userspace.
When handling the ETH_TP_MDI_AUTO case, the driver would set the
SPECIAL_CTRL_STS_AMDIX_ENABLE_ bit but neglected to set the required
SPECIAL_CTRL_STS_OVRRD_AMDIX_ bit. Without the override flag, the PHY
falls back to its hardware strap default, ignoring the software request.
This patch corrects the behavior by also setting the override bit when
enabling Auto-MDIX. This ensures that the userspace configuration takes
precedence over the hardware strap, allowing Auto-MDIX to be enabled
correctly in all scenarios.
Fixes: 05b35e7eb9a1 ("smsc95xx: add phylib support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andre Edich <andre.edich@microchip.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250703114941.3243890-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The previous commit unintentionally removed the code responsible for
enabling WoL via MMD3 register 0x8012 BIT5. As a result, Wake-on-LAN
(WoL) support for the QCA808X PHY is no longer functional.
The WoL (Wake-on-LAN) feature for the QCA808X PHY is enabled via MMD3
register 0x8012, BIT5. This implementation is aligned with the approach
used in at8031_set_wol().
Fixes: e58f30246c35 ("net: phy: at803x: fix the wol setting functions")
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250704-qcom_phy_wol_support-v1-2-053342b1538d@quicinc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the WoL (Wake-on-LAN) functionality to a shared library to enable
its reuse by the QCA808X PHY driver, incorporating support for WoL
functionality similar to the implementation in at8031_set_wol().
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Link: https://patch.msgid.link/20250704-qcom_phy_wol_support-v1-1-053342b1538d@quicinc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When performing a non-exact phy_caps lookup, we are looking for a
supported mode that matches as closely as possible the passed speed/duplex.
Blamed patch broke that logic by returning a match too early in case
the caller asks for half-duplex, as a full-duplex linkmode may match
first, and returned as a non-exact match without even trying to mach on
half-duplex modes.
Reported-by: Jijie Shao <shaojijie@huawei.com>
Closes: https://lore.kernel.org/netdev/20250603102500.4ec743cf@fedora/T/#m22ed60ca635c67dc7d9cbb47e8995b2beb5c1576
Tested-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Fixes: fc81e257d19f ("net: phy: phy_caps: Allow looking-up link caps based on speed and duplex")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250606094321.483602-1-maxime.chevallier@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When using publicly available tools like 'mdio-tools' to read/write data
from/to network interface and its PHY via C45 (clause 45) mdiobus,
there is no verification of parameters passed to the ioctl and
it accepts any mdio address.
Currently there is support for 32 addresses in kernel via PHY_MAX_ADDR define,
but it is possible to pass higher value than that via ioctl.
While read/write operation should generally fail in this case,
mdiobus provides stats array, where wrong address may allow out-of-bounds
read/write.
Fix that by adding address verification before C45 read/write operation.
While this excludes this access from any statistics, it improves security of
read/write operation.
Fixes: 4e4aafcddbbf ("net: mdio: Add dedicated C45 API to MDIO bus drivers")
Signed-off-by: Jakub Raczynski <j.raczynski@samsung.com>
Reported-by: Wenjing Shan <wenjing.shan@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using publicly available tools like 'mdio-tools' to read/write data
from/to network interface and its PHY via mdiobus, there is no verification of
parameters passed to the ioctl and it accepts any mdio address.
Currently there is support for 32 addresses in kernel via PHY_MAX_ADDR define,
but it is possible to pass higher value than that via ioctl.
While read/write operation should generally fail in this case,
mdiobus provides stats array, where wrong address may allow out-of-bounds
read/write.
Fix that by adding address verification before read/write operation.
While this excludes this access from any statistics, it improves security of
read/write operation.
Fixes: 080bb352fad00 ("net: phy: Maintain MDIO device and bus statistics")
Signed-off-by: Jakub Raczynski <j.raczynski@samsung.com>
Reported-by: Wenjing Shan <wenjing.shan@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge in late fixes to prepare for the 6.16 net-next PR.
No conflicts nor adjacent changes.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
We have noticed that when PHY timestamping is enabled, L2 frames seems
to be modified by changing two 2 bytes with a value of 0. The place were
these 2 bytes seems to be random(or I couldn't find a pattern). In most
of the cases the userspace can ignore these frames but if for example
those 2 bytes are in the correction field there is nothing to do. This
seems to happen when configuring the HW for IPv4 even that the flow is
not enabled.
These 2 bytes correspond to the UDPv4 checksum and once we don't enable
clearing the checksum when using L2 frames then the frame doesn't seem
to be changed anymore.
Fixes: 7d272e63e0979d ("net: phy: mscc: timestamping and PHC support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://patch.msgid.link/20250523082716.2935895-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Fix memory leak when running one-step timestamping. When running
one-step sync timestamping, the HW is configured to insert the TX time
into the frame, so there is no reason to keep the skb anymore. As in
this case the HW will never generate an interrupt to say that the frame
was timestamped, then the frame will never released.
Fix this by freeing the frame in case of one-step timestamping.
Fixes: 7d272e63e0979d ("net: phy: mscc: timestamping and PHC support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://patch.msgid.link/20250522115722.2827199-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a potential crash issue when disabling and re-enabling the
network port. When disabling the network port, phy_detach() calls
device_link_del() to remove the device link, but it does not clear
phydev->devlink, so phydev->devlink is not a NULL pointer. Then the
network port is re-enabled, but if phy_attach_direct() fails before
calling device_link_add(), the code jumps to the "error" label and
calls phy_detach(). Since phydev->devlink retains the old value from
the previous attach/detach cycle, device_link_del() uses the old value,
which accesses a NULL pointer and causes a crash. The simplified crash
log is as follows.
[ 24.702421] Call trace:
[ 24.704856] device_link_put_kref+0x20/0x120
[ 24.709124] device_link_del+0x30/0x48
[ 24.712864] phy_detach+0x24/0x168
[ 24.716261] phy_attach_direct+0x168/0x3a4
[ 24.720352] phylink_fwnode_phy_connect+0xc8/0x14c
[ 24.725140] phylink_of_phy_connect+0x1c/0x34
Therefore, phydev->devlink needs to be cleared when the device link is
deleted.
Fixes: bc66fa87d4fd ("net: phy: Add link between phy dev and mac dev")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250523083759.3741168-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add Airoha AN7583 PHY support based on Airoha AN7581 with the small
difference that BMCR_PDOWN is enabled by default and needs to be cleared
to make the internal PHY correctly work.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250522165313.6411-4-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for the MaxLinear MxL86110 Gigabit Ethernet PHY, a low-power,
cost-optimized transceiver supporting 10/100/1000 Mbps over twisted-pair
copper, compliant with IEEE 802.3.
The driver implements basic features such as:
- Device initialization
- RGMII interface timing configuration
- Wake-on-LAN support
- LED initialization and control via /sys/class/leds
This driver has been tested on multiple Variscite boards, including:
- VAR-SOM-MX93 (i.MX93)
- VAR-SOM-MX8M-PLUS (i.MX8MP)
Example boot log showing driver probe:
[ 7.692101] imx-dwmac 428a0000.ethernet eth0:
PHY [stmmac-0:00] driver [MXL86110 Gigabit Ethernet] (irq=POLL)
Signed-off-by: Stefano Radaelli <stefano.radaelli21@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250521212821.593057-1-stefano.radaelli21@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add support for Aeonsemi AS21xxx 10G C45 PHYs. These PHYs integrate
an IPC to setup some configuration and require special handling to
sync with the parity bit. The parity bit is a way the IPC use to
follow correct order of command sent.
Supported PHYs AS21011JB1, AS21011PB1, AS21010JB1, AS21010PB1,
AS21511JB1, AS21511PB1, AS21510JB1, AS21510PB1, AS21210JB1,
AS21210PB1 that all register with the PHY ID 0x7500 0x7510
before the firmware is loaded.
They all support up to 5 LEDs with various HW mode supported.
While implementing it was found some strange coincidence with using the
same logic for implementing C22 in MMD regs in Broadcom PHYs.
For reference here the AS21xxx PHY name logic:
AS21x1xxB1
^ ^^
| |J: Supports SyncE/PTP
| |P: No SyncE/PTP support
| 1: Supports 2nd Serdes
| 2: Not 2nd Serdes support
0: 10G, 5G, 2.5G
5: 5G, 2.5G
2: 2.5G
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250517201353.5137-6-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce new API, genphy_match_phy_device(), to provide a way to check
to match a PHY driver for a PHY device based on the info stored in the
PHY device struct.
The function generalize the logic used in phy_bus_match() to check the
PHY ID whether if C45 or C22 ID should be used for matching.
This is useful for custom .match_phy_device function that wants to use
the generic logic under some condition. (example a PHY is already setup
and provide the correct PHY ID)
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250517201353.5137-5-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Simplify .match_phy_device OP by using a generic function and using the
new phy_id PHY driver info instead of hardcoding the matching PHY ID
with new variant for macsec and no_macsec PHYs.
Also make use of PHY_ID_MATCH_MODEL macro and drop PHY_ID_MASK define to
introduce phy_id and phy_id_mask again in phy_driver struct.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250517201353.5137-4-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Simplify .match_phy_device OP by using a generic function and using the
new phy_id PHY driver info instead of hardcoding the matching PHY ID.
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://patch.msgid.link/20250517201353.5137-3-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pass PHY driver pointer to .match_phy_device OP in addition to phydev.
Having access to the PHY driver struct might be useful to check the
PHY ID of the driver is being matched for in case the PHY ID scanned in
the phydev is not consistent.
A scenario for this is a PHY that change PHY ID after a firmware is
loaded, in such case, the PHY ID stored in PHY device struct is not
valid anymore and PHY will manually scan the ID in the match_phy_device
function.
Having the PHY driver info is also useful for those PHY driver that
implement multiple simple .match_phy_device OP to match specific MMD PHY
ID. With this extra info if the parsing logic is the same, the matching
function can be generalized by using the phy_id in the PHY driver
instead of hardcoding.
Rust wrapper callback is updated to align to the new match_phy_device
arguments.
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Benno Lossin <lossin@kernel.org> # for Rust
Reviewed-by: FUJITA Tomonori <fujita.tomonori@gmail.com>
Link: https://patch.msgid.link/20250517201353.5137-2-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Constify the passed struct fixed_phy_status *status where possible.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/d1764b62-8538-408b-a4e3-b63715481a38@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All callers pass PHY_POLL, therefore remove irq argument from
fixed_phy_register().
Note: I keep the irq argument in fixed_phy_add_gpiod() for now,
for the case that somebody may want to use a GPIO interrupt in
the future, by e.g. adding a call to fwnode_irq_get() to
fixed_phy_get_gpiod().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/31cdb232-a5e9-4997-a285-cb9a7d208124@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All callers pass PHY_POLL, therefore remove irq argument from
fixed_phy_add().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Acked-by: Greg Ungerer <gerg@linux-m68k.org>
Link: https://patch.msgid.link/b3b9b3bc-c310-4a54-b376-c909c83575de@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for internal 2.5Gphy on MT7988. This driver will load
necessary firmware and add appropriate time delay to make sure
that firmware works stably. The firmware loading procedure takes
about 11ms in this driver.
Signed-off-by: Sky Huang <skylake.huang@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250516102327.2014531-3-SkyLake.Huang@mediatek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Sort config and file names in Kconfig and Makefile in
drivers/net/phy/mediatek/ in alphabetical order.
Signed-off-by: Sky Huang <skylake.huang@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250516102327.2014531-2-SkyLake.Huang@mediatek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
RTL8127-internal PHY is RTL8261C which is a integrated 10Gbps PHY with ID
0x001cc890. It follows the code path of RTL8125/RTL8126 internal NBase-T
PHY.
Signed-off-by: ChunHao Lin <hau@realtek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250516055622.3772-1-hau@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After having factored out the provider part from mdio_bus.c, we can
make the mdio consumer / device layer a separate module. This also
allows to remove Kconfig symbol MDIO_DEVICE.
The module init / exit functions from mdio_bus.c no longer have to be
called from phy_device.c. The link order defined in
drivers/net/phy/Makefile ensures that init / exit functions are called
in the right order.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/dba6b156-5748-44ce-b5e2-e8dc2fcee5a7@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The driver uses the name LAN88xx for PHYs with phy_id = 0x0007c132. But
with this placeholder name no documentation can be found on the net.
Document the fact that these PHYs are build into the LAN7800 and LAN7850
USB/Ethernet controllers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250515082051.2644450-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since its introduction 6 yrs ago this functions has never had a user.
So remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/ccbeef28-65ae-4e28-b1db-816c44338dee@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Current implementation requires syscon compatible for pio property
which is used for driving the switch leds on mt7988.
Replace syscon_regmap_lookup_by_phandle with of_parse_phandle and
device_node_to_regmap to get the regmap already assigned by pinctrl
driver.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://patch.msgid.link/20250510174933.154589-1-linux@fw-web.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.15-rc7).
Conflicts:
tools/testing/selftests/drivers/net/hw/ncdevmem.c
97c4e094a4b2 ("tests/ncdevmem: Fix double-free of queue array")
2f1a805f32ba ("selftests: ncdevmem: Implement devmem TCP TX")
https://lore.kernel.org/20250514122900.1e77d62d@canb.auug.org.au
Adjacent changes:
net/core/devmem.c
net/core/devmem.h
0afc44d8cdf6 ("net: devmem: fix kernel panic when netlink socket close after module unload")
bd61848900bf ("net: devmem: Implement TX path")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Enabling of the temperature sensor was moved from mv88q2xxx_hwmon_probe to
mv88q222x_config_init with the consequence that the sensor is only
usable when the PHY is configured. Enable the sensor in
mv88q2xxx_hwmon_probe as well to fix this.
Signed-off-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Link: https://patch.msgid.link/20250512-marvell-88q2xxx-hwmon-enable-at-probe-v4-1-9256a5c8f603@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
MDIO_DEVRES is only set where PHYLIB/PHYLINK are set which
select MDIO_DEVRES. So we can remove this symbol.
Note: Due to circular module dependencies we can't simply
make mdio_devres.c part of phylib.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/27cba535-f507-4b32-84a3-0744c783a465@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The KSZ9477 PHY driver contained workarounds for broken EEE capability
advertisements by manually masking supported EEE modes and forcibly
disabling EEE if MICREL_NO_EEE was set.
With proper MAC-side EEE handling implemented via phylink, these quirks
are no longer necessary. Remove MICREL_NO_EEE handling and the use of
ksz9477_get_features().
This simplifies the PHY driver and avoids duplicated EEE management logic.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org # v6.14+
Link: https://patch.msgid.link/20250504081434.424489-3-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Most PHY drivers default to a 2ns delay if internal delay is requested
and no value is specified. Having a default value makes sense, as it
allows a Device Tree to only care about board design (whether there are
delays on the PCB or not), and not whether the delay is added on the MAC
or the PHY side when needed.
Whether the delays are actually applied is controlled by the
DP83867_RGMII_*_CLK_DELAY_EN flags, so the behavior is only changed in
configurations that would previously be rejected with -EINVAL.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://patch.msgid.link/e2509b248a11ee29ea408a50c231da4c1fa0863b.1746612711.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The check that intended to handle "rgmii" PHY mode differently to the
RGMII modes with internal delay never worked as intended:
- added in commit 2a10154abcb7 ("net: phy: dp83867: Add TI dp83867 phy"):
logic error caused the condition to always evaluate to true
- changed in commit a46fa260f6f5 ("net: phy: dp83867: Fix warning check
for setting the internal delay"): now the condition incorrectly
evaluates to false for rgmii-txid
- removed in commit 2b892649254f ("net: phy: dp83867: Set up RGMII TX
delay")
Around the time of the removal, commit c11669a2757e ("net: phy: dp83867:
Rework delay rgmii delay handling") started clearing the delay enable
flags in RGMIICTL. The change attempted to preserve the historical
behavior of not disabling internal delays with "rgmii" PHY mode and also
documented this in a comment, but due to a conflict between "Set up
RGMII TX delay" and "Rework delay rgmii delay handling", the behavior
dp83867_verify_rgmii_cfg() warned about (and that was also described in
a comment in dp83867_config_init()) disappeared in the following merge
of net into net-next in commit b4b12b0d2f02
("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net").
While is doesn't appear that this breaking change was intentional, it
has been like this since 2019, and the new behavior to disable the delays
with "rgmii" PHY mode is generally desirable - in particular with MAC
drivers that have to fix up the delay mode, resulting in the PHY driver
not even seeing the same mode that was specified in the Device Tree.
Remove the obsolete check and comment.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://patch.msgid.link/8a286207cd11b460bb0dbd27931de3626b9d7575.1746612711.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Like the RTL8211F, the RTL8211E PHY supports up to three LEDs.
Add netdev trigger support for them, too.
Signed-off-by: Michael Klein <michael@fossekall.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250504172916.243185-7-michael@fossekall.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
rtl8211f_led_hw_control_get() does not need atomic bit operations,
replace set_bit() by __set_bit().
Signed-off-by: Michael Klein <michael@fossekall.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250504172916.243185-6-michael@fossekall.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Group macro definitions by PHY in lexicographic order. Within each PHY
block, definitions are order by page number and then register number.
Signed-off-by: Michael Klein <michael@fossekall.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250504172916.243185-5-michael@fossekall.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add some more defines for RTL8211F page and register numbers.
Signed-off-by: Michael Klein <michael@fossekall.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250504172916.243185-4-michael@fossekall.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Factor out RTL8211E extension page access code to
rtl821x_modify_ext_page() and clean up rtl8211e_config_init()
Signed-off-by: Michael Klein <michael@fossekall.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250504172916.243185-3-michael@fossekall.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
These macros have there since the first revision but were never used, so
let's just remove them.
Signed-off-by: Michael Klein <michael@fossekall.de>
Link: https://patch.msgid.link/20250504172916.243185-2-michael@fossekall.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Refactor to check if the fwnode we got is correct and return if so,
otherwise do additional checks. Using same pattern in all conditionals
makes it slightly easier to read and understand.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250430143802.3714405-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After 52358dd63e34 ("net: phy: remove function stubs") there's a
problem if CONFIG_MDIO_BUS is set, but CONFIG_PHYLIB is not.
mdiobus_scan() uses phylib functions like get_phy_device().
Bringing back the stub wouldn't make much sense, because it would
allow to compile mdiobus_scan(), but the function would be unusable.
The stub returned NULL, and we have the following in mdiobus_scan():
phydev = get_phy_device(bus, addr, c45);
if (IS_ERR(phydev))
return phydev;
So calling mdiobus_scan() w/o CONFIG_PHYLIB would cause a crash later in
mdiobus_scan(). In general the PHYLIB functionality isn't optional here.
Consequently, MDIO bus providers depend on PHYLIB.
Therefore factor it out and build it together with the libphy core
modules. In addition make all MDIO bus providers under /drivers/net/mdio
depend on PHYLIB. Same applies to enetc MDIO bus provider. Note that
PHYLIB selects MDIO_DEVRES, therefore we can omit this here.
Fixes: 52358dd63e34 ("net: phy: remove function stubs")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202504270639.mT0lh2o1-lkp@intel.com/
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/c74772a9-dab6-44bf-a657-389df89d85c2@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The RTL8211F supports multiple WOL modes. This patch adds support for
magic packets.
The PHY notifies the system via the INTB/PMEB pin when a WOL event
occurs.
Signed-off-by: Daniel Braunwarth <daniel.braunwarth@kuka.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250429-realtek_wol-v2-1-8f84def1ef2c@kuka.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Comment was erroneously added with /**, amend this to use /* as it is
not a kernel-doc.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202504262247.1UBrDBVN-lkp@intel.com/
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250428214920.813038-1-aryan.srivastava@alliedtelesis.co.nz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The defines for SUPPORTED_INTERFACES and ADVERTISED_INTERFACES both appear
to be unused. I couldn't find anything that actually references them in the
original diff that added them and it seems like they have persisted despite
using deprecated defines that aren't supposed to be used as per the
ethtool.h header that defines the bits they are composed of.
Since they are unused, and not supposed to be used anymore I am just
dropping the lines of code since they seem to just be occupying space.
Signed-off-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/174578398922.1580647.9720643128205980455.stgit@ahduyck-xeon-server.home.arpa
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.15-rc4).
This pull includes wireless and a fix to vxlan which isn't
in Linus's tree just yet. The latter creates with a silent conflict
/ build breakage, so merging it now to avoid causing problems.
drivers/net/vxlan/vxlan_vnifilter.c
094adad91310 ("vxlan: Use a single lock to protect the FDB table")
087a9eb9e597 ("vxlan: vnifilter: Fix unlocked deletion of default FDB entry")
https://lore.kernel.org/20250423145131.513029-1-idosch@nvidia.com
No "normal" conflicts, or adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The temperature sensor enabled for mv88q222x devices also functions for
mv88q211x based devices. Unify the two devices probe functions to enable
the sensors for all devices supported by this driver.
The same oddity as for mv88q222x devices exists, the PHY link must be up
for a correct temperature reading to be reported.
# cat /sys/class/hwmon/hwmon9/temp1_input
-75000
# ifconfig end5 up
# cat /sys/class/hwmon/hwmon9/temp1_input
59000
Worth noting is that while the temperature register offsets and layout
are the same between mv88q211x and mv88q222x devices their names in the
datasheets are different. This change keeps the mv88q222x names for the
mv88q211x support.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250418145800.2420751-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
