| Age | Commit message (Collapse) | Author |
|---|
|
Make sure to drop the references taken to the child devices by
of_find_device_by_node() during probe on driver unbind.
Fixes: c99993376f72 ("usb: dwc3: Add Amlogic G12A DWC3 glue")
Cc: stable@vger.kernel.org # 5.2
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20250724091910.21092-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure to drop the reference to the dwc3 device taken by
of_find_device_by_node() on probe errors and on driver unbind.
Fixes: 6dd2565989b4 ("usb: dwc3: add imx8mp dwc3 glue layer driver")
Cc: stable@vger.kernel.org # 5.12
Cc: Li Jun <jun.li@nxp.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20250724091910.21092-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB/Thunderbolt fixes in here for other patches to be on top
of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Leaving the USB BCR asserted prevents the associated GDSC to turn on. This
blocks any subsequent attempts of probing the device, e.g. after a probe
deferral, with the following showing in the log:
[ 1.332226] usb30_prim_gdsc status stuck at 'off'
Leave the BCR deasserted when exiting the driver to avoid this issue.
Cc: stable <stable@kernel.org>
Fixes: a4333c3a6ba9 ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250709132900.3408752-1-krishna.kurapati@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
argument
Now that the TRB reclaim logic always inspects the TRB's CHN (Chain) bit
directly to determine whether a TRB is part of a chain, the explicit
'chain' parameter passed into dwc3_gadget_ep_reclaim_completed_trb()
is no longer necessary.
This cleanup simplifies the reclaim code by avoiding duplication of
chain state tracking, and makes the reclaim logic rely entirely on the
hardware descriptor flags — which are already present and accurate at
this stage.
No functional changes intended.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johannes Schneider <johannes.schneider@leica-geosystems.com>
Link: https://lore.kernel.org/r/20250629090414.294308-2-johannes.schneider@leica-geosystems.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well to build on top of for other
changes that depend on them.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 96c7bf8f6b3e ("usb: dwc3: gadget: Cleanup SG handling") updated
the TRB reclaim path to use the TRB CHN (Chain) bit to determine whether
a TRB was part of a chain. However, this inadvertently changed the
behavior of reclaiming the final TRB in some scatter-gather or short
transfer cases.
In particular, if the final TRB did not have the CHN bit set, the
cleanup path could incorrectly skip clearing the HWO (Hardware Own)
bit, leaving stale TRBs in the ring. This resulted in broken data
transfer completions in userspace, notably for MTP over FunctionFS.
Fix this by unconditionally clearing the HWO bit during TRB reclaim,
regardless of the CHN bit state. This restores correct behavior
especially for transfers that require ZLPs or end on non-CHN TRBs.
Fixes: 61440628a4ff ("usb: dwc3: gadget: Cleanup SG handling")
Signed-off-by: Johannes Schneider <johannes.schneider@leica-geosystems.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/AM8PR06MB7521A29A8863C838B54987B6BC7BA@AM8PR06MB7521.eurprd06.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove the duplicate check for DWC3_EP_RESOURCE_ALLOCATED flag,
as its already checked inside dwc3_gadget_set_xfer_resource()
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250619120339.847708-1-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When dwc3_gadget_soft_disconnect() fails, dwc3_suspend_common() keeps
going with the suspend, resulting in a period where the power domain is
off, but the gadget driver remains connected. Within this time frame,
invoking vbus_event_work() will cause an error as it attempts to access
DWC3 registers for endpoint disabling after the power domain has been
completely shut down.
Abort the suspend sequence when dwc3_gadget_suspend() cannot halt the
controller and proceeds with a soft connect.
Fixes: 9f8a67b65a49 ("usb: dwc3: gadget: fix gadget suspend/resume")
Cc: stable <stable@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Kuen-Han Tsai <khtsai@google.com>
Link: https://lore.kernel.org/r/20250528100315.2162699-1-khtsai@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If device is coherent or if DMA (direct memory access) is translated by
an IOMMU then program USB2.0 IP to route transactions through the CCI for
coherency even if the target of transaction is in low power domain (LPD).
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1748976818-710088-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Adds a shutdown callback to ensure that the XHCI stack is properly
shutdown in reboot/shutdown path.
In kexec flow, kernel_restart_prepare() performs actions necessary
to prepare the system for a restart and invokes device_shutdown. To
ensure proper shutdown attach the dwc3 shutdown implementation which
mirrors the remove method.
$ kexec -e
<snip>
xhci-hcd xhci-hcd.0.auto: remove, state 1
usb usb1: USB disconnect, device number 1
usb 1-1: USB disconnect, device number 6
xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
kexec_core: Starting new kernel
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/1748977771-714153-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This SoC has a DWC3 compatible controllers. It needs "ref" and
"susp_clk" for it's operation.
Add required changes in exynos dwc3 glue layer to support this SoC.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Pritam Manohar Sutar <pritam.sutar@samsung.com>
Link: https://lore.kernel.org/r/20250516071333.3223226-3-pritam.sutar@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Qualcomm DWC3 glue driver duplicates the logic of the bulk clock
API to acquire, prepare, and unprepare the controller's clocks. It also
manages the life cycle of these handled explicitly.
Transition to the bulk clock API and manage the resources using devres,
to clean up the code. The resource acquisition is moved above the
initial reset pulse, to handle resource issues before the state is
touched - other than this, this no functional change.
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250508-dwc3-clk-bulk-v2-1-bad3427e88d4@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently gadget_wakeup() waits for U0 synchronously if it was
called from func_wakeup(), this is because we need to send the
function wakeup command soon after the link is active. And the
call is made synchronous by polling DSTS continuosly for 20000
times in __dwc3_gadget_wakeup(). But it observed that sometimes
the link is not active even after polling 20K times, leading to
remote wakeup failures. Adding a small delay between each poll
helps, but that won't guarantee resolution in future. Hence make
the gadget_wakeup completely asynchronous.
Since multiple interfaces can issue a function wakeup at once,
add a new variable wakeup_pending_funcs which will indicate the
functions that has issued func_wakup, this is represented in a
bitmap format. If the link is in U3, dwc3_gadget_func_wakeup()
will set the bit corresponding to interface_id and bail out.
Once link comes back to U0, linksts_change irq is triggered,
where the function wakeup command is sent based on bitmap.
Cc: stable <stable@kernel.org>
Fixes: 92c08a84b53e ("usb: dwc3: Add function suspend and function wakeup support")
Signed-off-by: Prashanth K <prashanth.k@oss.qualcomm.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250422103231.1954387-4-prashanth.k@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well, and this resolves the following
merge conflicts that were reported in linux-next:
drivers/usb/chipidea/ci_hdrc_imx.c
drivers/usb/host/xhci.h
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are two issues:
1) Return -EINVAL if platform_get_resource() fails. Don't return
success.
2) The devm_ioremap() function doesn't return error pointers, it returns
NULL. Update the check.
Fixes: 1881a32fe14d ("usb: dwc3: qcom: Transition to flattened model")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/aAijmfAph0FlTqg6@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The use of the old SET_SYSTEM_SLEEP_PM_OPS/SET_RUNTIME_PM_OPS macros
without __maybe_unused annotations causes warnings when build testing
without CONFIG_PM:
drivers/usb/dwc3/dwc3-qcom.c:421:12: error: unused function 'dwc3_qcom_suspend' [-Werror,-Wunused-function]
421 | static int dwc3_qcom_suspend(struct dwc3_qcom *qcom, bool wakeup)
| ^~~~~~~~~~~~~~~~~
drivers/usb/dwc3/dwc3-qcom.c:457:12: error: unused function 'dwc3_qcom_resume' [-Werror,-Wunused-function]
457 | static int dwc3_qcom_resume(struct dwc3_qcom *qcom, bool wakeup)
Change these to the modern SYSTEM_SLEEP_PM_OPS/RUNTIME_PM_OPS/pm_ptr
macros, which avoids the warnings and improves readability at the same
time.
Fixes: 1881a32fe14d ("usb: dwc3: qcom: Transition to flattened model")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250423162613.2082417-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USB IP-block found in most Qualcomm platforms is modelled in the
Linux kernel as 3 different independent device drivers, but as shown by
the already existing layering violations in the Qualcomm glue driver
they can not be operated independently.
With the current implementation, the glue driver registers the core and
has no way to know when this is done. As a result, e.g. the suspend
callbacks needs to guard against NULL pointer dereferences when trying
to peek into the struct dwc3 found in the drvdata of the child.
Even with these checks, there are no way to fully protect ourselves from
the race conditions that occur if the DWC3 is unbound.
Missing from the upstream Qualcomm USB support is handling of role
switching, in which the glue needs to be notified upon DRD mode changes.
Several attempts has been made through the years to register callbacks
etc, but they always fall short when it comes to handling of the core's
probe deferral on resources etc.
Moving to a model where the DWC3 core is instantiated in a synchronous
fashion avoids above described race conditions.
It is however not feasible to do so without also flattening the
DeviceTree binding, as assumptions are made in the DWC3 core and
frameworks used that the device's associated of_node will the that of
the core. Furthermore, the DeviceTree binding is a direct
representation of the Linux driver model, and doesn't necessarily
describe "the USB IP-block".
The Qualcomm DWC3 glue driver is therefor transitioned to initialize and
operate the DWC3 within the one device context, in synchronous fashion.
To provide a limited time backwards compatibility, a snapshot of the
driver is retained in a previous commit. As such no care is taken in the
dwc3-qcom driver for the qcom,dwc3 backwards compatibility.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250414-dwc3-refactor-v7-6-f015b358722d@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With the upcoming transition to a model where DWC3 core and glue operate
on a single struct device the drvdata datatype will change to be owned
by the core.
The drvdata is however used by the Qualcomm DWC3 glue to pass the qcom
glue context around before the core is allocated.
Remove this problem, and clean up the code, by passing the dwc3_qcom
struct around during probe, instead of acquiring it from the drvdata.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250414-dwc3-refactor-v7-5-f015b358722d@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the core is integrated with glue, it's reasonable to assume that
the glue driver will have to touch the IP before/after the core takes
the hardware out and into reset. As such the glue must own these
resources and be allowed to turn them on/off outside the core's
handling.
Allow the platform or glue layer to indicate if the core logic for
clocks and resets should be skipped to deal with this.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250414-dwc3-refactor-v7-4-f015b358722d@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The DWC3 IP block is handled by three distinct device drivers: XHCI,
DWC3 core and a platform specific (optional) DWC3 glue driver.
This has resulted in, at least in the case of the Qualcomm glue, the
presence of a number of layering violations, where the glue code either
can't handle, or has to work around, the fact that core might not probe
deterministically.
An example of this is that the suspend path should operate slightly
different depending on the device operating in host or peripheral mode,
and the only way to determine the operating state is to peek into the
core's drvdata.
The Qualcomm glue driver is expected to make updates in the qscratch
register region (the "glue" region) during role switch events, but with
the glue and core split using the driver model, there is no reasonable
way to introduce listeners for mode changes.
Split the dwc3 core platform_driver callbacks and their implementation
and export the implementation, to make it possible to deterministically
instantiate the dwc3 core as part of the dwc3 glue drivers and to
allow flattening of the DeviceTree representation.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250414-dwc3-refactor-v7-3-f015b358722d@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In order to more tightly integrate the Qualcomm glue driver with the
dwc3 core the driver is redesigned to avoid splitting the implementation
using the driver model. But due to the strong coupling to the Devicetree
binding needs to be updated as well.
Various ways to provide backwards compatibility with existing Devicetree
blobs has been explored, but migrating the Devicetree information
between the old and the new binding is non-trivial.
For the vast majority of boards out there, the kernel and Devicetree are
generated and handled together, which in practice means that backwards
compatibility needs to be managed across about 1 kernel release.
For some though, such as the various Snapdragon laptops, the Devicetree
blobs live a life separate of the kernel. In each one of these, with the
continued extension of new features, it's recommended that users would
upgrade their Devicetree somewhat frequently.
With this in mind, simply carrying a snapshot/copy of the current driver
is simpler than creating and maintaining the migration code.
The driver is kept under the same Kconfig option, to ensure that Linux
distributions doesn't drop USB support on these platforms.
The driver, which is going to be refactored to handle the newly
introduced qcom,snps-dwc3 compatible, is updated to temporarily not
match against any compatible.
This driver should be removed after the next LTS release.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250414-dwc3-refactor-v7-1-f015b358722d@oss.qualcomm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add Exynos2200 compatible string and associated driver data. This SoC
requires a Link interface AXI clock.
Signed-off-by: Ivaylo Ivanov <ivo.ivanov.ivanov1@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250412203313.738429-3-ivo.ivanov.ivanov1@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The event count is read from register DWC3_GEVNTCOUNT.
There is a check for the count being zero, but not for exceeding the
event buffer length.
Check that event count does not exceed event buffer length,
avoiding an out-of-bounds access when memcpy'ing the event.
Crash log:
Unable to handle kernel paging request at virtual address ffffffc0129be000
pc : __memcpy+0x114/0x180
lr : dwc3_check_event_buf+0xec/0x348
x3 : 0000000000000030 x2 : 000000000000dfc4
x1 : ffffffc0129be000 x0 : ffffff87aad60080
Call trace:
__memcpy+0x114/0x180
dwc3_interrupt+0x24/0x34
Signed-off-by: Frode Isaksen <frode@meta.com>
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable <stable@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250403072907.448524-1-fisaksen@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The "reset" GPIO controls the RESET signal to an external, usually
ULPI PHY, chip. The original code path acquires the signal in LOW
state, and then immediately asserts it HIGH again, if the reset
signal defaulted to asserted, there'd be a short "spike" before the
reset.
Here is what happens depending on the pre-existing state of the reset
signal:
Reset (previously asserted): ~~~|_|~~~~|_______
Reset (previously deasserted): _____|~~~~|_______
^ ^ ^
A B C
At point A, the low going transition is because the reset line is
requested using GPIOD_OUT_LOW. If the line is successfully requested,
the first thing we do is set it high _without_ any delay. This is
point B. So, a glitch occurs between A and B.
Requesting the line using GPIOD_OUT_HIGH eliminates the A and B
transitions. Instead we get:
Reset (previously asserted) : ~~~~~~~~~~|______
Reset (previously deasserted): ____|~~~~~|______
^ ^
A C
Where A and C are the points described above in the code. Point B
has been eliminated.
The issue was found during code inspection.
Also remove the cryptic "toggle ulpi .." comment.
Fixes: ca05b38252d7 ("usb: dwc3: xilinx: Add gpio-reset support")
Cc: stable <stable@kernel.org>
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250318064518.9320-1-mike.looijmans@topic.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
dwc3 device suspend/resume callbacks were being triggered during system
suspend and resume even if the device was already runtime-suspended.
This is redundant for device mode because the suspend and resume routines
are essentially identical for system PM and runtime PM.
To prevent these unnecessary callbacks, indicate to the PM core that it
can safely leave the device in runtime suspend if it's already
runtime-suspended in device mode by returning a positive value in
prepare() callback. This optimization only applies to devices without
pinctrl, as pinctrl has distinct logic tied to system suspend/resume.
Signed-off-by: Roy Luo <royluo@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250312223434.3071598-1-royluo@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Allow for the DWC3 host driver to pass along XHCI property that defines
how many interrupters to allocate. This is in relation for the number of
event rings that can be potentially used by other processors within the
system.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Puma Hsu <pumahsu@google.com>
Tested-by: Daehwan Jung <dh10.jung@samsung.com>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20250409194804.3773260-7-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is a revert of
commit 04fb365c453e ("usb: dwc3: replace %p with %pK")
When the formatting was changed from %p to %pK that was a security
improvement, as %p would leak raw pointer values to the kernel log.
Since commit ad67b74d2469 ("printk: hash addresses printed with %p")
the regular %p has been improved to avoid this issue.
On the other hand, restricted pointers ("%pK") were never meant to be used
through printk(). They can unintentionally still leak raw pointers or
acquire sleeping looks in atomic contexts.
Switch back to regular %p again.
Link: https://lore.kernel.org/lkml/20250113171731-dc10e3c1-da64-4af0-b767-7c7070468023@linutronix.de/
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de>
Link: https://lore.kernel.org/r/20250310-restricted-pointers-usb-v2-2-a7598e2d47d1@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Resolves the merge conflict with:
drivers/usb/typec/ucsi/ucsi_acpi.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After phy initialization, some phy operations can only be executed while
in lower P states. Ensure GUSB3PIPECTL.SUSPENDENABLE and
GUSB2PHYCFG.SUSPHY are set soon after initialization to avoid blocking
phy ops.
Previously the SUSPENDENABLE bits are only set after the controller
initialization, which may not happen right away if there's no gadget
driver or xhci driver bound. Revise this to clear SUSPENDENABLE bits
only when there's mode switching (change in GCTL.PRTCAPDIR).
Fixes: 6d735722063a ("usb: dwc3: core: Prevent phy suspend during init")
Cc: stable <stable@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/633aef0afee7d56d2316f7cc3e1b2a6d518a8cc9.1738280911.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Exynos7870 devices have a DWC3 compatible USB 2.0 controller.
Add support in the driver by:
- Adding its own compatible string, "samsung,exynos7870-dwusb3".
- Adding three USBDRD clocks named "bus_early", "ref", and "ctrl", to
be controlled by the driver.
Signed-off-by: Kaustabh Chakraborty <kauschluss@disroot.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250301-exynos7870-usb-v3-2-f01697165d19@disroot.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While commit d325a1de49d6 ("usb: dwc3: gadget: Prevent losing events in
event cache") makes sure that top half(TH) does not end up overwriting the
cached events before processing them when the TH gets invoked more than one
time, returning IRQ_HANDLED results in occasional irq storm where the TH
hogs the CPU. The irq storm can be prevented by the flag before event
handler busy is cleared. Default enable interrupt moderation in all
versions which support them.
ftrace event stub during dwc3 irq storm:
irq/504_dwc3-1111 ( 1111) [000] .... 70.000866: irq_handler_exit: irq=14 ret=handled
irq/504_dwc3-1111 ( 1111) [000] .... 70.000872: irq_handler_entry: irq=504 name=dwc3
irq/504_dwc3-1111 ( 1111) [000] .... 70.000874: irq_handler_exit: irq=504 ret=handled
irq/504_dwc3-1111 ( 1111) [000] .... 70.000881: irq_handler_entry: irq=504 name=dwc3
irq/504_dwc3-1111 ( 1111) [000] .... 70.000883: irq_handler_exit: irq=504 ret=handled
irq/504_dwc3-1111 ( 1111) [000] .... 70.000889: irq_handler_entry: irq=504 name=dwc3
irq/504_dwc3-1111 ( 1111) [000] .... 70.000892: irq_handler_exit: irq=504 ret=handled
irq/504_dwc3-1111 ( 1111) [000] .... 70.000898: irq_handler_entry: irq=504 name=dwc3
irq/504_dwc3-1111 ( 1111) [000] .... 70.000901: irq_handler_exit: irq=504 ret=handled
irq/504_dwc3-1111 ( 1111) [000] .... 70.000907: irq_handler_entry: irq=504 name=dwc3
irq/504_dwc3-1111 ( 1111) [000] .... 70.000909: irq_handler_exit: irq=504 ret=handled
irq/504_dwc3-1111 ( 1111) [000] .... 70.000915: irq_handler_entry: irq=504 name=dwc3
irq/504_dwc3-1111 ( 1111) [000] .... 70.000918: irq_handler_exit: irq=504 ret=handled
irq/504_dwc3-1111 ( 1111) [000] .... 70.000924: irq_handler_entry: irq=504 name=dwc3
irq/504_dwc3-1111 ( 1111) [000] .... 70.000927: irq_handler_exit: irq=504 ret=handled
irq/504_dwc3-1111 ( 1111) [000] .... 70.000933: irq_handler_entry: irq=504 name=dwc3
irq/504_dwc3-1111 ( 1111) [000] .... 70.000935: irq_handler_exit: irq=504 ret=handled
....
Cc: stable <stable@kernel.org>
Suggested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Fixes: d325a1de49d6 ("usb: dwc3: gadget: Prevent losing events in event cache")
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250216223003.3568039-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use syscon_regmap_lookup_by_phandle_args() which is a wrapper over
syscon_regmap_lookup_by_phandle() combined with getting the syscon
argument. Except simpler code this annotates within one line that given
phandle has arguments, so grepping for code would be easier.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250212202913.23443-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Intel Merrifield SoC uses these endpoints for tracing and they cannot
be re-allocated if being used because the side band flow control signals
are hard wired to certain endpoints:
• 1 High BW Bulk IN (IN#1) (RTIT)
• 1 1KB BW Bulk IN (IN#8) + 1 1KB BW Bulk OUT (Run Control) (OUT#8)
In device mode, since RTIT (EP#1) and EXI/RunControl (EP#8) uses
External Buffer Control (EBC) mode, these endpoints are to be mapped to
EBC mode (to be done by EXI target driver). Additionally TRB for RTIT
and EXI are maintained in STM (System Trace Module) unit and the EXI
target driver will as well configure the TRB location for EP #1 IN
and EP#8 (IN and OUT). Since STM/PTI and EXI hardware blocks manage
these endpoints and interface to OTG3 controller through EBC interface,
there is no need to enable any events (such as XferComplete etc)
for these end points.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250212193116.2487289-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The snps,reserved-endpoints property lists the reserved endpoints
that shouldn't be used for normal transfers. Add support for that
to the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250212193116.2487289-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Prepare the gadget driver to handle the reserved endpoints that will be
not allocated at the initialisation time.
While at it, add a warning where the NULL endpoint should never happen.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250212193116.2487289-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a frequent timeout during controller enter/exit from halt state
after toggling the run_stop bit by SW. This timeout occurs when
performing frequent role switches between host and device, causing
device enumeration issues due to the timeout. This issue was not present
when USB2 suspend PHY was disabled by passing the SNPS quirks
(snps,dis_u2_susphy_quirk and snps,dis_enblslpm_quirk) from the DTS.
However, there is a requirement to enable USB2 suspend PHY by setting of
GUSB2PHYCFG.ENBLSLPM and GUSB2PHYCFG.SUSPHY bits when controller starts
in gadget or host mode results in the timeout issue.
This commit addresses this timeout issue by ensuring that the bits
GUSB2PHYCFG.ENBLSLPM and GUSB2PHYCFG.SUSPHY are cleared before starting
the dwc3_gadget_run_stop sequence and restoring them after the
dwc3_gadget_run_stop sequence is completed.
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Selvarasu Ganesan <selvarasu.g@samsung.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250201163903.459-1-selvarasu.g@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add missing description to the nostream_work of dwc3_ep. The work is
used by bulk multi-stream endpoints for a NoStream event to reinitiate
the stream if needed.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Closes: https://lore.kernel.org/linux-next/20250120182219.30dcb3c6@canb.auug.org.au/
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/7cdeaa346d24907712aac533c1c5f90a03151189.1737500936.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, DWC3 driver attempts to acquire the USB power supply only
once during the probe. If the USB power supply is not ready at that
time, the driver simply ignores the failure and continues the probe,
leading to permanent non-functioning of the gadget vbus_draw callback.
Address this problem by delaying the dwc3 driver initialization until
the USB power supply is registered.
Fixes: 6f0764b5adea ("usb: dwc3: add a power supply for current control")
Cc: stable <stable@kernel.org>
Signed-off-by: Kyle Tso <kyletso@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250115044548.2701138-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are too many different host behaviors when it comes to NoStream
handling, and not everyone follows the USB and xHCI spec. The DWC3
driver attempts to do some guess work to interop with different hosts,
but it can't cover everything. Let's keep it simple and treat every host
the same: just retry on NoStream after a 100ms of no response delay.
Note that some hosts cannot handle frequent retries. This may affect
performance on certain defective hosts, but NoStream is a rare
occurrence and interoperability is more important.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/b92ae94c86f01f165d5f178b7767898573b6dc75.1736819308.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well for testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 533561a8aad5 ("usb: dwc3: omap: Use
devm_regulator_get_optional()") assumed NULL was returned, but
devm_regulator_get_optional() returns -ENODEV rather than NULL like
other *_get_optional() functions.
Fixes: 533561a8aad5 ("usb: dwc3: omap: Use devm_regulator_get_optional()")
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250109170748.3852439-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM_SLEEP support is simpler and less error prone than the
use of #ifdef based kernel configuration guards.
Signed-off-by: Raphael Gallais-Pou <rgallaispou@gmail.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250109152055.52931-1-rgallaispou@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
phy_syscon_pll_refclk() leaks an OF node obtained by
of_parse_phandle_with_fixed_args(), thus add an of_node_put() call.
Cc: stable <stable@kernel.org>
Fixes: e8784c0aec03 ("drivers: usb: dwc3: Add AM62 USB wrapper driver")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250109001638.70033-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the system begins to enter suspend mode, dwc3_suspend() is called
by PM suspend. There is a problem that if someone interrupt the system
suspend process between dwc3_suspend() and pm_suspend() of its parent
device, PM suspend will be canceled and attempt to resume suspended
devices so that dwc3_resume() will be called. However, dwc3 and its
parent device (like the power domain or glue driver) may already be
suspended by runtime PM in fact. If this sutiation happened, the
pm_runtime_set_active() in dwc3_resume() will return an error since
parent device was suspended. This can lead to unexpected behavior if
DWC3 proceeds to execute dwc3_resume_common().
EX.
RPM suspend: ... -> dwc3_runtime_suspend()
-> rpm_suspend() of parent device
...
PM suspend: ... -> dwc3_suspend() -> pm_suspend of parent device
^ interrupt, so resume suspended device
... <- dwc3_resume() <-/
^ pm_runtime_set_active() returns error
To prevent the problem, this commit will skip dwc3_resume_common() and
return the error if pm_runtime_set_active() fails.
Fixes: 68c26fe58182 ("usb: dwc3: set pm runtime active before resume common")
Cc: stable <stable@kernel.org>
Signed-off-by: Ray Chi <raychi@google.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20250106082240.3822059-1-raychi@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The 'vbus-supply' regulator is optional, so use
devm_regulator_get_optional() instead of checking for property presence
first.
While here, rework the error handling to use dev_err_probe() which
handles deferred probe correctly without an error message.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20241231164456.262581-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The UDC state in sysfs (/sys/class/udc/<udc>/state) should accurately
reflect the current state of the USB Device Controller.
Currently, the UDC state is not handled consistently during gadget
disconnection. While the disconnect interrupt path correctly sets the
state to "not-attached", manual deconfiguration leaves the state in
"configured", misrepresenting the actual situation.
This commit ensures consistent UDC state handling by setting the state to
"not-attached" after manual deconfiguration. This accurately reflects the
UDC's state and provides a consistent behavior regardless of the
disconnection method.
Signed-off-by: Roy Luo <royluo@google.com>
Reviewed-by: André Draszik <andre.draszik@linaro.org>
Tested-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20241223042536.1465299-1-royluo@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Runtime PM documentation (Section 5) mentions, during remove()
callbacks, drivers should undo the runtime PM changes done in
probe(). Usually this means calling pm_runtime_disable(),
pm_runtime_dont_use_autosuspend() etc. Hence add missing
function to disable autosuspend on dwc3-am62 driver unbind.
Fixes: e8784c0aec03 ("drivers: usb: dwc3: Add AM62 USB wrapper driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20241209105728.3216872-1-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
