| Age | Commit message (Collapse) | Author |
|---|
|
Pull SoC devicetree updates from Arnd Bergmann:
"There is new support for additional on-chip devices on Apple,
Mediatek, Renesas, Rockchip, Samsung, Google, TI, ST, Nvidia and
Amlogic devices.
The Arm Morello reference platform gets a devicetree for booting in
normal aarch64 mode. The hardware supports experimental CHERI support,
which requires a modified kernel.
The AMD (formerly Xilinx) Versal NET SoC gets added, this is a
combined FPGA with Cortex-A78 CPUs in a SoC.
Six new ST STM32MP2 SoC variants are added. Like the earlier
STM32MP25, the MP211, MP213, MP215, MP231, MP233 and MP235 models are
based on one or two Cortex-A35 cores but each feature a different set
of I/O devices.
Mediatek MT8370 is a minor variation of MT8390 with fewer CPU and GPU
cores
Apple T2 is the baseboard management controller on earlier Intel CPU
based Macs, with 16 models now gaining initial support.
All the above come with dts files for the reference boards. In
addition, these boards are added for the SoCs that are already
supported:
- The Milk-V Jupiter board based on SpacemiT K1/M1
- NetCube Systems Kumquat board based on the 32-bit Allwinner V3s SoC
- Three boards based on 32-bit stm32mp1
- 11 distinct board variants from Toradex and one from Variscite, all
based on i.MX6
- Google Pixel Pro 6 phone based on gs101 (Tensor)
- Three additional variants of the i.MX8MP based "Skov" board
- A second variant of the i.MX95 EVK board
- Two boards based on Renesas SoCs
- Four boards based the Rockchip RK35xx series, plus the RK3588 'MNT
Reform 2' laptop"
* tag 'soc-dt-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (538 commits)
arm64: dts: Add gpio_intc node for Amlogic A5 SoCs
arm64: dts: Add gpio_intc node for Amlogic A4 SoCs
arm64: dts: hi3660: Add property for fixing CPUIdle
arm64: dts: rockchip: remove ethm0_clk0_25m_out from Sige5 gmac0
arm64: dts: marvell: Use preferred node names for "simple-bus"
arm64: dts: marvell: Drop unused CP11X_TYPE define
arm64: dts: marvell: Move arch timer and pmu nodes to top-level
arm64: dts: rockchip: Fix PWM pinctrl names
arm64: dts: rockchip: fix RK3576 SCMI clock IDs
dt-bindings: clock: rk3576: add SCMI clocks
arm64: dts: rockchip: Fix pcie reset gpio on Orange Pi 5 Max
arm64: dts: amd/seattle: Drop undocumented "spi-controller" properties
arm64: dts: amd/seattle: Fix bus, mmc, and ethernet node names
arm64: dts: amd/seattle: Move and simplify fixed clocks
arm64: dts: amd/seattle: Base Overdrive B1 on top of B0 version
arm64: dts: rockchip: Enable HDMI audio output for ArmSoM Sige7
arm64: dts: rockchip: Enable onboard eMMC on Radxa E20C
arm64: dts: rockchip: Add SDHCI controller for RK3528
arm64: dts: rockchip: Remove bluetooth node from rock-3a
arm64: dts: rockchip: Move rk356x scmi SHMEM to reserved memory
...
|
|
Whether the MII transmit clock can be stopped is primarily a property
of the PHY (there is a capability bit that should be checked first.)
Whether the MAC is capable of stopping the transmit clock is a separate
issue, but this is already handled by the core DesignWare MAC code.
As commit "net: stmmac: stm32: use PHY capability for TX clock stop"
adds the flag to use the PHY capability, remove the DT property that is
now unecessary.
Cc: Samin Guo <samin.guo@starfivetech.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1tsIUA-005vGX-8A@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Introduce the devicetree for the Plymovent AQM board
(stm32mp151c-plyaqm), based on the STM32MP151 SoC.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20250305131425.1491769-5-o.rempel@pengutronix.de
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add pinmux groups required for the Plymovent AQM board.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20250305131425.1491769-4-o.rempel@pengutronix.de
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
LDO2 is expansion connector supply on STM32MP13xx DHCOR DHSBC rev.200.
LDO5 is carrier board supply on STM32MP13xx DHCOR DHSBC rev.200. Keep
both regulators always enabled to make sure both the carrier board and
the expansion connector is always powered on and supplied with correct
voltage.
Describe ST33TPHF2XSPI TPM 2.0 chip interrupt and reset lines.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20250302152605.54792-1-marex@denx.de
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Replace the number 2 with the appropriate numerical constant defined in
dt-bindings/interrupt-controller/irq.h.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Antonio Borneo <antonio.borneo@foss.st.com>
Link: https://lore.kernel.org/r/20250310122402.8795-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
As indicated by the board silkscreen, there are three user LEDs.
Add the missing one.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20250217114513.1098844-2-dario.binacchi@amarulasolutions.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Associate the LED node name with the corresponding board silkscreen for
more precise identification. In fact, the board has a total of seven
LEDs, some of which are user-controllable (i. e. usr{1,2,3}), while
others are directly controlled by hardware (e. g. power, overcurrent,
...). All these LEDs are either green or red, so using the names
led-green and led-red for the two LEDs mapped in the DTS does not
simplify their identification on the board.
Moreover, this patch is a prerequisite for adding the usr3 LED, which
has not been included in the DTS.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20250217114513.1098844-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add node for user push button.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20250217114332.1098482-2-dario.binacchi@amarulasolutions.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add node for the user led.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20250217114332.1098482-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Introduce the devicetree for the Priva E-Measuringbox board
(stm32mp133c-prihmb), based on the STM32MP133 SoC.
Signed-off-by: Roan van Dijk <roan@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20250203085820.609176-5-o.rempel@pengutronix.de
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add thermal zone configuration and sensor node for STM32MP131 SoC.
Signed-off-by: Roan van Dijk <roan@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20250203085820.609176-4-o.rempel@pengutronix.de
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The Linux Automation GmbH FairyTux2 is a small Linux device based on
an Octavo Systems OSD32MP153c SiP, that occupies just two slots on a
DIN rail.
The device contains an eMMC for storage, a gigabit Ethernet
connection, a CAN bus and a RS485 transceiver.
Add support for the lxa-fairytux2 generation 1 and 2 boards based on
the STM32MP153c.
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into soc/dt
Add and enable MALI400 support for STiH410-b2260
* tag 'sti-dt-for-v6.14-round1' of https://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: dts: st: enable the MALI gpu on the stih410-b2260
ARM: dts: st: add node for the MALI gpu on stih410.dtsi
dt-bindings: gpu: mali-utgard: Add st,stih410-mali compatible
Link: https://lore.kernel.org/r/f44cb1f0-4d91-4e25-8b1f-3dd9a7bed62b@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Enable the GPU on the stih410-b2260 board.
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Add the entry for the GPU (Mali400) on the stih410.dtsi
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
Swap USART3 and UART8 aliases on STM32MP15xx DHCOM SoM,
make sure UART8 is listed first, USART3 second, because
the UART8 is labeled as UART2 on the SoM pinout, while
USART3 is labeled as UART3 on the SoM pinout.
Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Enable the counter nodes without dedicated pins. With such configuration,
the counter interface can be used on internal clock to generate events.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Enable the counter nodes without dedicated pins. With such configuration,
the counter interface can be used on internal clock to generate events.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Enable the counter nodes without dedicated pins. With such configuration,
the counter interface can be used on internal clock to generate events.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Counter driver originally had support limited to quadrature interface
and simple counter. It has been improved[1], so add the remaining
stm32 timer counter nodes.
[1] https://lore.kernel.org/linux-arm-kernel/20240307133306.383045-1-fabrice.gasnier@foss.st.com/
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Counter driver originally had support limited to quadrature interface
and simple counter. It has been improved[1], so add the remaining
stm32 timer counter nodes.
[1] https://lore.kernel.org/linux-arm-kernel/20240307133306.383045-1-fabrice.gasnier@foss.st.com/
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add support for the lxa-tac generation 3 board based on the
STM32MP153c.
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
This is a preparation patch in order to add lxa-tac generation 3
board.
As the gen3 board has a different adc and gpio{e,g} setups, move these
from the stm32mp15xc-lxa-tac.dtsi to the gen{1,2}.dts files.
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Allow providing the Ethernet and mass storage functions on the USB
peripheral port at the same time.
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Some of the userspace software and tests depend on the can/i2c/spi
devices having the same name on every boot. This may not always be the
case based on e.g. parallel probe order.
Assign static device numbers to all can/i2c/spi devices.
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The RTC was enabled under the false assumption that the SoM already
contains a suitable 32.768 kHz crystal.
It does however not contain such a crystal and since none is fitted
externally to the SoM the RTC can not be used on the hardware.
Reflect that in the devicetree.
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The GIC IRQ type used for IPCC RX should be IRQ_TYPE_LEVEL_HIGH.
Replacing the interrupt with the EXTI event changes the type to
the numeric value 1, meaning IRQ_TYPE_EDGE_RISING.
The issue is that EXTI event 61 is a direct event.The IRQ type of
direct events is not used by EXTI and is propagated to the parent
IRQ controller of EXTI, the GIC.
Align the IRQ type to the value expected by the GIC by replacing
the second parameter "1" with IRQ_TYPE_LEVEL_HIGH.
Fixes: 7d9802bb0e34 ("ARM: dts: stm32: remove the IPCC "wakeup" IRQ on stm32mp151")
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Move the M24256E write-lockable page subnode after RTC subnode in
DH STM32MP13xx DHCOR SoM DT to keep the list of nodes sorted by I2C
address. No functional change.
Fixes: 3f2e7d167307 ("ARM: dts: stm32: Describe M24256E write-lockable page in DH STM32MP13xx DHCOR SoM DT")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The STM32MP13xx DHCOR DHSBC is populated with STM32MP13xx part capable
of 1 GHz operation, increase the CPU core voltage to 1.35 V to make
sure the SoC is stable even if the blobs unconditionally force the CPU
to 1 GHz operation.
It is not possible to make use of CPUfreq on the STM32MP13xx because
the SCMI protocol 0x13 is not implemented by upstream OpTee-OS which
is the SCMI provider.
Fixes: 6331bddce649 ("ARM: dts: stm32: Add support for STM32MP13xx DHCOR SoM and DHSBC board")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
DHCOM SoM
Deduplicate /aliases { serialN = ... } and /chosen node into
stm32mp15xx-dhcom-som.dtsi , since the content is identical
on all carrier boards using the STM32MP15xx DHCOM SoM. No
functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
property
Remove "pl022,slave-tx-disable" property which is both unused in the kernel
and undocumented. Most likely they are leftovers from downstream.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20241115193835.3623725-1-robh@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into soc/dt
STM32 DT for v6.13, round 1
Highlights:
----------
- MPU:
- STM32MP13:
- ST DK board:
- Add support of WLAN/BT Murata Type 1DX module.
- DH SOM:
- Add M24256E EEPROM suport.
- STMP32MP15:
- Use IWDG2 as wakeup source.
- Add support of WLAN/BT Murata Type 1DX module on DK2 board.
- STM32MP25:
- Enable RTC.
- Add DMA support for U(S)ART, I2C and SPI instances.
* tag 'stm32-dt-for-v6.13-1' of https://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
arm64: dts: st: add DMA support on SPI instances of stm32mp25
arm64: dts: st: add DMA support on I2C instances of stm32mp25
arm64: dts: st: add DMA support on U(S)ART instances of stm32mp25
arm64: dts: st: add RNG node on stm32mp251
arm64: dts: st: enable RTC on stm32mp257f-ev1 board
arm64: dts: st: add RTC on stm32mp25x
ARM: dts: stm32: add support of WLAN/BT on stm32mp135f-dk
ARM: dts: stm32: add support of WLAN/BT on stm32mp157c-dk2
ARM: dts: stm32: rtc, add LSCO to WLAN/BT module on stm32mp135f-dk
ARM: dts: stm32: rtc, add LSCO to WLAN/BT module on stm32mp157c-dk2
ARM: dts: stm32: rtc, add pin to provide LSCO on stm32mp13
ARM: dts: stm32: rtc, add pin to provide LSCO on stm32mp15
ARM: dts: stm32: Describe M24256E write-lockable page in DH STM32MP13xx DHCOR SoM DT
ARM: dts: stm32: Add IWDG2 EXTI interrupt mapping and mark as wakeup source
Link: https://lore.kernel.org/r/92d2d6df-cc5c-488f-8ebd-550b1903db12@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add support of WLAN/BT Murata Type 1DX module:
- usart2 is used for Bluetooth interface
- sdmmc2 is used for WLAN (sdio) interface
Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add support of WLAN/BT Murata Type 1DX module:
- usart2 is used for Bluetooth interface
- sdmmc2 is used for WLAN (sdio) interface
Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
On stm32mp135f-dk board, WLAN/BT module LPO_IN pin is wired to
RTC OUT2_RMP pin.
Provide a pinctrl configuration to enable LSCO on OUT2_RMP.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
On stm32mp157c-dk2 board, WLAN/BT module LPO_IN pin is wired to
RTC OUT2_RMP pin.
Provide a pinctrl configuration to enable LSCO on OUT2_RMP.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Declare pin for LSCO in stm32-pinctrl provider node to reserve this pin
for RTC OUT2_RMP, in stm32mp13-pinctrl.dtsi.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Declare pin for LSCO in stm32-pinctrl provider node to reserve this pin
for RTC OUT2_RMP, in stm32mp15-pinctrl.dtsi.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
DHCOR SoM DT
The STM32MP13xx DHCOR SoM is populated with M24256E EEPROM which has
Additional Write lockable page at separate I2C address. Describe the
page in DT to make it available.
Note that the WLP page on this device is hardware write-protected by
R37 which pulls the nWC signal high to VDD_3V3_1V8 power rail.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The IWDG2 is capable of generating pre-timeout interrupt, which can be used
to wake the system up from suspend to mem. Add the EXTI interrupt mapping
and mark the IWDG2 as wake up source.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The eMMC interface was configured to configure the FBCLK
into the Alt A setting, but this should be in GPIO mode
and available for use as a reset line. Move it to the new
mc_a_2 setting, and define this config in the generic
options.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241019-ux500-dts-updates-v1-2-a89bfbd0f680@linaro.org
|
|
The Codina Zinitix touchscreens have touchkeys for HOME and
BACK, add these now that the driver and bindings support it.
Cc: Nikita Travkin <nikita@trvn.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241019-ux500-dts-updates-v1-1-a89bfbd0f680@linaro.org
|
|
DHCOM PDK2
By default the SGTL5000 derives bit and frame clock from MCLK, which
does not produce particularly accurate results. The SGTL5000 PLL does
improve the accuracy, but also increases power consumption. Using the
SoC SAI interface as bit and frame clock source results in the best
accuracy without the power consumption increase downside. Switch the
bit and frame clock direction from SAI to SGTL5000, reduce mclk-fs to
match.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Switch the bitclock-master and frame-master properties from phandle to
flag on STM32MP15xx DHCOM PDK2. There is no real reason to use phandle
in this system DT, since the phandle points to the endpoint node which
contains the property itself. Simplify the DT. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Sort properties alphabetically in audio endpoints of STM32MP15xx
DHCOM PDK2 DT. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Introduce device tree support for the MECIO1 and MECT1S board variants.
MECIO1 is an I/O and motor control board used in blood sample analysis
machines. MECT1S is a 1000Base-T1 switch for internal machine networks
of blood sample analysis machines.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Rename 'pins1' to 'pins' in the qspi_bk1_pins_a node to correct the
subnode name. The incorrect name caused the configuration to be
applied to the wrong subnode, resulting in QSPI not working properly.
Some additional changes was made:
- To avoid this kind of regression, all references to pin configuration
nodes are now referenced directly using the format &{label/subnode}.
- /delete-property/ bias-disable; was added everywhere where bias-pull-up
is used
- redundant properties like driver-push-pull are removed
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The RTL8211 PHY on DH STM32MP13xx DHCOR DHSBC carrier board supports HW
LED offload, the LEDs can be configured on link at 10/100/1000 line rate
and on RXTX activity. There are two PHYs on this board, each only has two
out of three LEDs connected to the PHY LED outputs. Describe this hardware
configuration in DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
This enables DDR50 mode for the eMMC on Octavo OSD32MP1-RED board.
Fixes: be78ab4f632c ("ARM: dts: stm32: add initial support for stm32mp157-odyssey board")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
