| Age | Commit message (Collapse) | Author |
|---|
|
Move the EST structure to struct stmmac_priv, because the
EST configs don't look like platform config, but EST is
enabled in runtime with the settings retrieved for the TC
TAPRIO feature also in runtime. So it's better to have the
EST-data preserved in the driver private data instead of
the platform data storage.
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20240513014346.1718740-3-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Reinitialize the whole EST structure would also reset the mutex
lock which is embedded in the EST structure, and then trigger
the following warning. To address this, move the lock to struct
stmmac_priv. We also need to reacquire the mutex lock when doing
this initialization.
DEBUG_LOCKS_WARN_ON(lock->magic != lock)
WARNING: CPU: 3 PID: 505 at kernel/locking/mutex.c:587 __mutex_lock+0xd84/0x1068
Modules linked in:
CPU: 3 PID: 505 Comm: tc Not tainted 6.9.0-rc6-00053-g0106679839f7-dirty #29
Hardware name: NXP i.MX8MPlus EVK board (DT)
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : __mutex_lock+0xd84/0x1068
lr : __mutex_lock+0xd84/0x1068
sp : ffffffc0864e3570
x29: ffffffc0864e3570 x28: ffffffc0817bdc78 x27: 0000000000000003
x26: ffffff80c54f1808 x25: ffffff80c9164080 x24: ffffffc080d723ac
x23: 0000000000000000 x22: 0000000000000002 x21: 0000000000000000
x20: 0000000000000000 x19: ffffffc083bc3000 x18: ffffffffffffffff
x17: ffffffc08117b080 x16: 0000000000000002 x15: ffffff80d2d40000
x14: 00000000000002da x13: ffffff80d2d404b8 x12: ffffffc082b5a5c8
x11: ffffffc082bca680 x10: ffffffc082bb2640 x9 : ffffffc082bb2698
x8 : 0000000000017fe8 x7 : c0000000ffffefff x6 : 0000000000000001
x5 : ffffff8178fe0d48 x4 : 0000000000000000 x3 : 0000000000000027
x2 : ffffff8178fe0d50 x1 : 0000000000000000 x0 : 0000000000000000
Call trace:
__mutex_lock+0xd84/0x1068
mutex_lock_nested+0x28/0x34
tc_setup_taprio+0x118/0x68c
stmmac_setup_tc+0x50/0xf0
taprio_change+0x868/0xc9c
Fixes: b2aae654a479 ("net: stmmac: add mutex lock to protect est parameters")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20240513014346.1718740-2-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce a mechanism whereby platforms can create their PCS instances
prior to the network device being published to userspace, but after
some of the core stmmac initialisation has been completed. This means
that the data structures that platforms need will be available.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Co-developed-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://lore.kernel.org/r/20240513-rzn1-gmac1-v7-4-6acf58b5440d@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for configuring queueMaxSDU. As DWMAC IPs doesn't support
queueMaxSDU table handle this in the SW. The maximum 802.3 frame size
that is allowed to be transmitted by any queue is queueMaxSDU +
16 bytes (i.e. 6 bytes SA + 6 bytes DA + 4 bytes FCS).
Inspired from intel i225 driver.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The status bits of register MAC_FPE_CTRL_STS are clear on read. Using
32-bit read for MAC_FPE_CTRL_STS in dwmac5_fpe_configure() and
dwmac5_fpe_send_mpacket() clear the status bits. Then the stmmac interrupt
handler missing FPE event status and leads to FPE handshaking failure and
retries.
To avoid clear status bits of MAC_FPE_CTRL_STS in dwmac5_fpe_configure()
and dwmac5_fpe_send_mpacket(), add fpe_csr to stmmac_fpe_cfg structure to
cache the control bits of MAC_FPE_CTRL_STS and to avoid reading
MAC_FPE_CTRL_STS in those methods.
Fixes: 5a5586112b92 ("net: stmmac: support FPE link partner hand-shaking procedure")
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jianheng Zhang <Jianheng.Zhang@synopsys.com>
Link: https://lore.kernel.org/r/CY5PR12MB637225A7CF529D5BE0FBE59CBF81A@CY5PR12MB6372.namprd12.prod.outlook.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
plat_stmmacenet_data::ext_snapshot_num
Do not store bitmask for enabling AUX_SNAPSHOT0. The previous commit
("net: stmmac: fix PPS capture input index") takes care of calculating
the proper bit mask from the request data's extts.index field, which is
0 if not explicitly specified otherwise.
Signed-off-by: Johannes Zink <j.zink@pengutronix.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add sw fallback of tx checksum calculation for those tx queues that
don't support tx checksum offloading. DW xGMAC IP can be synthesized
such that it can support tx checksum offloading only for a few
initial tx queues. Also as Serge pointed out, for the DW QoS IP, tx
coe can be individually configured for each tx queue.
So when tx coe is enabled, for any tx queue that doesn't support
tx coe with 'coe-unsupported' flag set will have a sw fallback
happen in the driver for tx checksum calculation when any packets to
be transmitted on these tx queues.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clarify the difference between "interface" and "phy_interface" in
struct plat_stmmacenet_data, both by adding a comment, and also
renaming "interface" to be "mac_interface". The difference between
these are:
MAC ----- optional PCS ----- SerDes ----- optional PHY ----- Media
^ ^
mac_interface phy_interface
Note that phylink currently only deals with phy_interface.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qZq83-005tts-6K@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All users of plat->phylink_node first convert it to a fwnode. Rather
than repeatedly convert to a fwnode, store it as a fwnode. To reflect
this change, call it plat->port_node instead - it is used for more
than just phylink.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qZAX8-005pTo-OT@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A mode parameter has been added to the callback function of fix_mac_speed
to indicate the physical layer type.
The mode can be one the following:
MLO_AN_PHY - Conventional PHY
MLO_AN_FIXED - Fixed-link mode
MLO_AN_INBAND - In-band protocol
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://lore.kernel.org/r/20230807160716.259072-2-shenwei.wang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The IEEE1588 Standard specifies that the timestamps of Packets must be
captured when the PTP message timestamp point (leading edge of first
octet after the start of frame delimiter) crosses the boundary between
the node and the network. As the MAC latches the timestamp at an
internal point, the captured timestamp must be corrected for the
additional data transmission latency, as described in the publicly
available datasheet [1].
This patch only corrects for the MAC-Internal delay, which can be read
out from the MAC_Ingress_Timestamp_Latency register on DWMAC version 5,
since the Phy framework currently does not support querying the Phy
ingress and egress latency. The Closs Domain Crossing Circuits errors as
indicated in [1] are already being accounted in the
stmmac_get_tx_hwtstamp() function and are not corrected here.
As the Latency varies for different link speeds and MII
modes of operation, the correction value needs to be updated on each
link state change.
As the delay also causes a phase shift in the timestamp counter compared
to the rest of the network, this correction will also reduce phase error
when generating PPS outputs from the timestamp counter.
Since the correction registers may be unavailable on some hardware and
no feature bits are documented for dynamically detection of the MAC
propagation delay readout, introduce a feature bit to explicitely enable
MAC delay Correction in the gluecode driver.
[1] i.MX8MP Reference Manual, rev.1 Section 11.7.2.5.3 "Timestamp
correction"
Signed-off-by: Johannes Zink <j.zink@pengutronix.de>
Link: https://lore.kernel.org/r/20230719-stmmac_correct_mac_delay-v2-1-3366f38ee9a6@pengutronix.de
Link: https://lore.kernel.org/r/20230719-stmmac_correct_mac_delay-v3-1-61e63427735e@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The priv variable is _always_ of type (struct stmmac_priv *), so let's
stop using (void *) since it isn't abstracting anything.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230725211853.895832-3-ahalaney@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drop the boolean field of the plat_stmmacenet_data structure in favor of a
simple bitfield flag.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230710090001.303225-13-brgl@bgdev.pl
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drop the boolean field of the plat_stmmacenet_data structure in favor of a
simple bitfield flag.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230710090001.303225-12-brgl@bgdev.pl
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drop the boolean field of the plat_stmmacenet_data structure in favor of a
simple bitfield flag.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230710090001.303225-11-brgl@bgdev.pl
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drop the boolean field of the plat_stmmacenet_data structure in favor of a
simple bitfield flag.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230710090001.303225-10-brgl@bgdev.pl
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drop the boolean field of the plat_stmmacenet_data structure in favor of a
simple bitfield flag.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230710090001.303225-9-brgl@bgdev.pl
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drop the boolean field of the plat_stmmacenet_data structure in favor of a
simple bitfield flag.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230710090001.303225-8-brgl@bgdev.pl
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drop the boolean field of the plat_stmmacenet_data structure in favor of a
simple bitfield flag.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230710090001.303225-7-brgl@bgdev.pl
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drop the boolean field of the plat_stmmacenet_data structure in favor of a
simple bitfield flag.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230710090001.303225-6-brgl@bgdev.pl
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drop the boolean field of the plat_stmmacenet_data structure in favor of a
simple bitfield flag.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230710090001.303225-5-brgl@bgdev.pl
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drop the boolean field of the plat_stmmacenet_data structure in favor of a
simple bitfield flag.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230710090001.303225-4-brgl@bgdev.pl
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drop the boolean field of the plat_stmmacenet_data structure in favor of a
simple bitfield flag.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230710090001.303225-3-brgl@bgdev.pl
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
struct plat_stmmacenet_data contains several boolean fields that could be
easily replaced with a common integer 'flags' bitfield and bit defines.
Start the process with the has_integrated_pcs field.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230710090001.303225-2-brgl@bgdev.pl
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On some platforms, the PCS can be integrated in the MAC so the driver
will not see any PCS link activity. Add a switch that allows the platform
drivers to let the core code know.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some platforms have dwmac4 implementations that have a different
address space layout than the default, resulting in the need to define
their own DMA/MTL offsets.
Extend the functions to allow a platform driver to indicate what its
addresses are, overriding the defaults.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This patch adds support for platform-specific reset logic in the
stmmac driver. Some SoCs require a different reset mechanism than
the standard dwmac IP reset. To support these platforms, a new function
pointer 'fix_soc_reset' is added to the plat_stmmacenet_data structure.
The stmmac_reset in hwif.h is modified to call the 'fix_soc_reset'
function if it exists. This enables the driver to use the platform-specific
reset logic when necessary.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230403222302.328262-1-shenwei.wang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently DMA address width is either read from a RO device register
or force set from the platform data. This breaks DMA when the host DMA
address width is <=32it but the device is >32bit.
Right now the driver may decide to use a 2nd DMA descriptor for
another buffer (happens in case of TSO xmit) assuming that 32bit
addressing is used due to platform configuration but the device will
still use both descriptor addresses as one address.
This can be observed with the Intel EHL platform driver that sets
32bit for addr64 but the MAC reports 40bit. The TX queue gets stuck in
case of TCP with iptables NAT configuration on TSO packets.
The logic should be like this: Whatever we do on the host side (memory
allocation GFP flags) should happen with the host DMA width, whenever
we decide how to set addresses on the device registers we must use the
device DMA address width.
This patch renames the platform address width field from addr64 (term
used in device datasheet) to host_addr and uses this value exclusively
for host side operations while all chip operations consider the device
DMA width as read from the device register.
Fixes: 7cfc4486e7ea ("stmmac: intel: Configure EHL PSE0 GbE and PSE1 GbE to 32 bits DMA addressing")
Signed-off-by: Jochen Henneberg <jh@henneberg-systemdesign.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently in phy_init_eee() the driver unconditionally configures the PHY
to stop RX_CLK after entering Rx LPI state. This causes an LPI interrupt
storm on my qcs404-base board.
Change the PHY initialization so that for "qcom,qcs404-ethqos" compatible
device RX_CLK continues to run even in Rx LPI state.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Tegra MGBE ethernet controller requires that the SERDES link is
powered-up after the PHY link is up, otherwise the link fails to
become ready following a resume from suspend. Add a variable to indicate
that the SERDES link must be powered-up after the PHY link.
Signed-off-by: Revanth Kumar Uppala <ruppala@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 'has_crossts' flag was not used anywhere in the stmmac driver,
removing it from both header file and dwmac-intel driver.
Signed-off-by: Wong Vee Khee <veekhee@apple.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20220817064324.10025-1-veekhee@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Using current implementation of polling mode, there is high chances we
will hit into timeout error when running phc2sys. Hence, update the
implementation of hardware crosstimestamping to use the MAC interrupt
service routine instead of polling for TSIS bit in the MAC Timestamp
Interrupt Status register to be set.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on DesignWare Ethernet QoS datasheet, we are seeing the limitation
of Split Header (SPH) feature is not supported for Ipv4 fragmented packet.
This SPH limitation will cause ping failure when the packets size exceed
the MTU size. For example, the issue happens once the basic ping packet
size is larger than the configured MTU size and the data is lost inside
the fragmented packet, replaced by zeros/corrupted values, and leads to
ping fail.
So, disable the Split Header for Intel platforms.
v2: Add fixes tag in commit message.
Fixes: 67afd6d1cfdf("net: stmmac: Add Split Header support and enable it in XGMAC cores")
Cc: <stable@vger.kernel.org> # 5.10.x
Suggested-by: Ong, Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dwmac-qcom-ethqos currently exposes a mechanism to dump rgmii registers
after the 'stmmac_dvr_probe()' returns. However with commit
5ec55823438e ("net: stmmac: add clocks management for gmac driver"),
we now let 'pm_runtime_put()' disable the clocks before returning from
'stmmac_dvr_probe()'.
This causes a crash when 'rgmii_dump()' register dumps are enabled,
as the clocks are already off.
Since other dwmac drivers (possible future users as well) might
require a similar register dump feature, introduce a platform level
callback to allow the same.
This fixes the crash noticed while enabling rgmii_dump() dumps in
dwmac-qcom-ethqos driver as well. It also allows future changes
to keep a invoking the register dump callback from the correct
place inside 'stmmac_dvr_probe()'.
Fixes: 5ec55823438e ("net: stmmac: add clocks management for gmac driver")
Cc: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The clock domain crossing error (CDC) is calculated at every fetch of Tx or Rx
timestamps. It includes a division. Especially on arm32 based systems it is
expensive. It also requires two conditionals in the hotpath.
Add a compensation value cache to struct plat_stmmacenet_data and subtract it
unconditionally in the RX/TX functions which spares the conditionals.
The value is initialized to 0 and if supported calculated in the PTP
initialization code.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20211122111931.135135-1-kurt@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After adjusting the ptp time, the Qbv base time may be the past time
of the new current time. dwmac5 hardware limited the base time cannot
be set as past time. This patch add a btr_reserve to store the base
time get from qopt, then calculate the base time and reset the Qbv
configuration after ptp time adjust.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a mutex lock to protect est structure parameters so that the
EST parameters can be updated by other threads.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current stmmac driver WOL implementation will enable MAC WOL
if MAC HW PMT feature is on. Else, the driver will check for
PHY WOL support. There is another case where MAC HW PMT is
enabled but the platform still goes for the PHY WOL option.
E.g, Intel platform are designed for PHY WOL but not MAC WOL
although HW MAC PMT features are enabled.
Introduce use_phy_wol platform data to select PHY WOL
instead of depending on HW PMT features. Set use_phy_wol
will disable the plat->pmt which currently used to
determine the system to wake up by MAC WOL or PHY WOL.
Signed-off-by: Ling Pei Lee <pei.lee.ling@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are currently assuming that GMAC_AHB_RESET will already be deasserted
by the bootloader. However if this has not been done, probing of the GMAC
will fail. To remedy this we must ensure GMAC_AHB_RESET has been deasserted
prior to probing.
v2 changes:
- remove NULL condition check for stmmac_ahb_rst in stmmac_main.c
- unwrap dev_err() message in stmmac_main.c
- add PTR_ERR() around plat->stmmac_ahb_rst in stmmac_platform.c
v3 changes:
- add error pointer to dev_err() output
- add reset_control_assert(stmmac_ahb_rst) in stmmac_dvr_remove
- revert PTR_ERR() around plat->stmmac_ahb_rst since this is performed
on the returned value of ret by the calling function
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Intel mGbE supports 2.5Gbps link speed by increasing the clock rate by
2.5 times of the original rate. In this mode, the serdes/PHY operates at a
serial baud rate of 3.125 Gbps and the PCS data path and GMII interface of
the MAC operate at 312.5 MHz instead of 125 MHz.
For Intel mGbE, the overclocking of 2.5 times clock rate to support 2.5G is
only able to be configured in the BIOS during boot time. Kernel driver has
no access to modify the clock rate for 1Gbps/2.5G mode. The way to
determined the current 1G/2.5G mode is by reading a dedicated adhoc
register through mdio bus. In short, after the system boot up, it is either
in 1G mode or 2.5G mode which not able to be changed on the fly.
Compared to 1G mode, the 2.5G mode selects the 2500BASEX as PHY interface and
disables the xpcs_an_inband. This is to cater for some PHYs that only
supports 2500BASEX PHY interface with no autonegotiation.
v2: remove MAC supported link speed masking
v3: Restructure to introduce intel_speed_mode_2500() to read serdes registers
for max speed supported and select the appropritate configuration.
Use max_speed to determine the supported link speed mask.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On Intel platforms, not all safety features are enabled on the hardware.
The current implementation enable all safety features by default. This
will cause mass error and warning printouts after the module is loaded.
Introduce platform specific safety features flag to enable or disable
each safety features.
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Link xpcs callback functions for MAC to configure the xpcs EEE feature.
The clk_eee frequency is used to calculate the MULT_FACT_100NS. This is
to adjust the clock tic closer to 100ns.
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DWMAC Core 5.20 onwards supports HW descriptor prefetching.
Additionally, it also depends on platform specific RTL configuration.
This capability could be enabled by setting DMA_Mode bit-19 (DCHE).
So, to enable this cability, platform must set plat->dma_cfg->dche = true
and the DWMAC core version must be 5.20 onwards. Else, this capability
wouldn`t be configured
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Synopsis MAC controller supports auxiliary snapshot feature that
allows user to store a snapshot of the system time based on an external
event.
This patch add supports to the above mentioned feature. Users will be
able to triggered capturing the time snapshot from user-space using
application such as testptp or any other applications that uses the
PTP_EXTTS_REQUEST ioctl request.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Tan Tee Min <tee.min.tan@intel.com>
Co-developed-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For interrupt mode INTM=0, TX/RX transfer complete will trigger signal
not only on sbd_perch_[tx|rx]_intr_o (Transmit/Receive Per Channel) but
also on the sbd_intr_o (Common).
As for multi-MSI implementation, setting interrupt mode INTM=1 is more
efficient as each TX intr and RX intr (TI/RI) will be handled by TX/RX ISR
without the need of calling the common MAC ISR.
Updated the TX/RX NORMAL interrupts status checking process as the
NIS status bit is not asserted for any RI/TI events for INTM=1.
Signed-off-by: Wong, Vee Khee <vee.khee.wong@intel.com>
Co-developed-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now we introduce MSI interrupt service routines and hook these routines
up if stmmac_open() sees valid irq line being requested:-
stmmac_mac_interrupt() :- MAC (dev->irq), WOL (wol_irq), LPI (lpi_irq)
stmmac_safety_interrupt() :- Safety Feat Correctible Error (sfty_ce_irq)
& Uncorrectible Error (sfty_ue_irq)
stmmac_msi_intr_rx() :- For all RX MSI irq (rx_irq)
stmmac_msi_intr_tx() :- For all TX MSI irq (tx_irq)
Each of IRQs will have its unique name so that we can differentiate
them easily under /proc/interrupts.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to discover whether remote station supports frame preemption,
local station sends verify mPacket and expects response mPacket in
return from the remote station.
So, we add the functions to send and handle event when verify mPacket
and response mPacket are exchanged between the networked stations.
The mechanism to handle different FPE states between local and remote
station (link partner) is implemented using workqueue which starts a
task each time there is some sign of verify & response mPacket exchange
as check in FPE IRQ event. The task retries couple of times to try to
spot the states that both stations are ready to enter FPE ON. This allows
different end points to enable FPE at different time and verify-response
mPacket can happen asynchronously. Ultimately, the task will only turn
FPE ON when local station have both exchange response in both directions.
Thanks to Voon Weifeng for implementing the core functions for detecting
FPE events and send mPacket and phylink related change.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Co-developed-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Co-developed-by: Tan Tee Min <tee.min.tan@intel.com>
Signed-off-by: Tan Tee Min <tee.min.tan@intel.com>
Co-developed-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cross timestamping is supported on Integrated Ethernet Controller in
Intel SoC such as EHL and TGL with Always Running Timer.
The hardware cross-timestamp result is made available to
applications through the PTP_SYS_OFFSET_PRECISE ioctl which calls
stmmac_getcrosststamp().
Device time is stored in the MAC Auxiliary register. The 64-bit System
time (ART timestamp) is stored in registers that are only addressable
by using MDIO space.
Signed-off-by: Tan Tee Min <tee.min.tan@intel.com>
Co-developed-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Intel mGbE variant implemented in EHL and TGL can be set to select
different clock frequency based on GPO bits in MAC_GPIO_STATUS register.
We introduce a new "void (*ptp_clk_freq_config)(void *priv)" in platform
data so that if a platform is required to configure the frequency of clock
source, in this case Intel mGBE does, the platform-specific configuration
of the PTP clock setting is done when stmmac_ptp_register() is called.
Signed-off-by: Wong, Vee Khee <vee.khee.wong@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Co-developed-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch intends to add platform level clocks management. Some
platforms may have their own special clocks, they also need to be
managed dynamically. If you want to manage such clocks, please implement
clks_config callback.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
