| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Wrap datapath globals into net_aligned_data, to avoid false sharing
- Preserve MSG_ZEROCOPY in forwarding (e.g. out of a container)
- Add SO_INQ and SCM_INQ support to AF_UNIX
- Add SIOCINQ support to AF_VSOCK
- Add TCP_MAXSEG sockopt to MPTCP
- Add IPv6 force_forwarding sysctl to enable forwarding per interface
- Make TCP validation of whether packet fully fits in the receive
window and the rcv_buf more strict. With increased use of HW
aggregation a single "packet" can be multiple 100s of kB
- Add MSG_MORE flag to optimize large TCP transmissions via sockmap,
improves latency up to 33% for sockmap users
- Convert TCP send queue handling from tasklet to BH workque
- Improve BPF iteration over TCP sockets to see each socket exactly
once
- Remove obsolete and unused TCP RFC3517/RFC6675 loss recovery code
- Support enabling kernel threads for NAPI processing on per-NAPI
instance basis rather than a whole device. Fully stop the kernel
NAPI thread when threaded NAPI gets disabled. Previously thread
would stick around until ifdown due to tricky synchronization
- Allow multicast routing to take effect on locally-generated packets
- Add output interface argument for End.X in segment routing
- MCTP: add support for gateway routing, improve bind() handling
- Don't require rtnl_lock when fetching an IPv6 neighbor over Netlink
- Add a new neighbor flag ("extern_valid"), which cedes refresh
responsibilities to userspace. This is needed for EVPN multi-homing
where a neighbor entry for a multi-homed host needs to be synced
across all the VTEPs among which the host is multi-homed
- Support NUD_PERMANENT for proxy neighbor entries
- Add a new queuing discipline for IETF RFC9332 DualQ Coupled AQM
- Add sequence numbers to netconsole messages. Unregister
netconsole's console when all net targets are removed. Code
refactoring. Add a number of selftests
- Align IPSec inbound SA lookup to RFC 4301. Only SPI and protocol
should be used for an inbound SA lookup
- Support inspecting ref_tracker state via DebugFS
- Don't force bonding advertisement frames tx to ~333 ms boundaries.
Add broadcast_neighbor option to send ARP/ND on all bonded links
- Allow providing upcall pid for the 'execute' command in openvswitch
- Remove DCCP support from Netfilter's conntrack
- Disallow multiple packet duplications in the queuing layer
- Prevent use of deprecated iptables code on PREEMPT_RT
Driver API:
- Support RSS and hashing configuration over ethtool Netlink
- Add dedicated ethtool callbacks for getting and setting hashing
fields
- Add support for power budget evaluation strategy in PSE /
Power-over-Ethernet. Generate Netlink events for overcurrent etc
- Support DPLL phase offset monitoring across all device inputs.
Support providing clock reference and SYNC over separate DPLL
inputs
- Support traffic classes in devlink rate API for bandwidth
management
- Remove rtnl_lock dependency from UDP tunnel port configuration
Device drivers:
- Add a new Broadcom driver for 800G Ethernet (bnge)
- Add a standalone driver for Microchip ZL3073x DPLL
- Remove IBM's NETIUCV device driver
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- support zero-copy Tx of DMABUF memory
- take page size into account for page pool recycling rings
- Intel (100G, ice, idpf):
- idpf: XDP and AF_XDP support preparations
- idpf: add flow steering
- add link_down_events statistic
- clean up the TSPLL code
- preparations for live VM migration
- nVidia/Mellanox:
- support zero-copy Rx/Tx interfaces (DMABUF and io_uring)
- optimize context memory usage for matchers
- expose serial numbers in devlink info
- support PCIe congestion metrics
- Meta (fbnic):
- add 25G, 50G, and 100G link modes to phylink
- support dumping FW logs
- Marvell/Cavium:
- support for CN20K generation of the Octeon chips
- Amazon:
- add HW clock (without timestamping, just hypervisor time access)
- Ethernet virtual:
- VirtIO net:
- support segmentation of UDP-tunnel-encapsulated packets
- Google (gve):
- support packet timestamping and clock synchronization
- Microsoft vNIC:
- add handler for device-originated servicing events
- allow dynamic MSI-X vector allocation
- support Tx bandwidth clamping
- Ethernet NICs consumer, and embedded:
- AMD:
- amd-xgbe: hardware timestamping and PTP clock support
- Broadcom integrated MACs (bcmgenet, bcmasp):
- use napi_complete_done() return value to support NAPI polling
- add support for re-starting auto-negotiation
- Broadcom switches (b53):
- support BCM5325 switches
- add bcm63xx EPHY power control
- Synopsys (stmmac):
- lots of code refactoring and cleanups
- TI:
- icssg-prueth: read firmware-names from device tree
- icssg: PRP offload support
- Microchip:
- lan78xx: convert to PHYLINK for improved PHY and MAC management
- ksz: add KSZ8463 switch support
- Intel:
- support similar queue priority scheme in multi-queue and
time-sensitive networking (taprio)
- support packet pre-emption in both
- RealTek (r8169):
- enable EEE at 5Gbps on RTL8126
- Airoha:
- add PPPoE offload support
- MDIO bus controller for Airoha AN7583
- Ethernet PHYs:
- support for the IPQ5018 internal GE PHY
- micrel KSZ9477 switch-integrated PHYs:
- add MDI/MDI-X control support
- add RX error counters
- add cable test support
- add Signal Quality Indicator (SQI) reporting
- dp83tg720: improve reset handling and reduce link recovery time
- support bcm54811 (and its MII-Lite interface type)
- air_en8811h: support resume/suspend
- support PHY counters for QCA807x and QCA808x
- support WoL for QCA807x
- CAN drivers:
- rcar_canfd: support for Transceiver Delay Compensation
- kvaser: report FW versions via devlink dev info
- WiFi:
- extended regulatory info support (6 GHz)
- add statistics and beacon monitor for Multi-Link Operation (MLO)
- support S1G aggregation, improve S1G support
- add Radio Measurement action fields
- support per-radio RTS threshold
- some work around how FIPS affects wifi, which was wrong (RC4 is
used by TKIP, not only WEP)
- improvements for unsolicited probe response handling
- WiFi drivers:
- RealTek (rtw88):
- IBSS mode for SDIO devices
- RealTek (rtw89):
- BT coexistence for MLO/WiFi7
- concurrent station + P2P support
- support for USB devices RTL8851BU/RTL8852BU
- Intel (iwlwifi):
- use embedded PNVM in (to be released) FW images to fix
compatibility issues
- many cleanups (unused FW APIs, PCIe code, WoWLAN)
- some FIPS interoperability
- MediaTek (mt76):
- firmware recovery improvements
- more MLO work
- Qualcomm/Atheros (ath12k):
- fix scan on multi-radio devices
- more EHT/Wi-Fi 7 features
- encapsulation/decapsulation offload
- Broadcom (brcm80211):
- support SDIO 43751 device
- Bluetooth:
- hci_event: add support for handling LE BIG Sync Lost event
- ISO: add socket option to report packet seqnum via CMSG
- ISO: support SCM_TIMESTAMPING for ISO TS
- Bluetooth drivers:
- intel_pcie: support Function Level Reset
- nxpuart: add support for 4M baudrate
- nxpuart: implement powerup sequence, reset, FW dump, and FW loading"
* tag 'net-next-6.17' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1742 commits)
dpll: zl3073x: Fix build failure
selftests: bpf: fix legacy netfilter options
ipv6: annotate data-races around rt->fib6_nsiblings
ipv6: fix possible infinite loop in fib6_info_uses_dev()
ipv6: prevent infinite loop in rt6_nlmsg_size()
ipv6: add a retry logic in net6_rt_notify()
vrf: Drop existing dst reference in vrf_ip6_input_dst
net/sched: taprio: align entry index attr validation with mqprio
net: fsl_pq_mdio: use dev_err_probe
selftests: rtnetlink.sh: remove esp4_offload after test
vsock: remove unnecessary null check in vsock_getname()
igb: xsk: solve negative overflow of nb_pkts in zerocopy mode
stmmac: xsk: fix negative overflow of budget in zerocopy mode
dt-bindings: ieee802154: Convert at86rf230.txt yaml format
net: dsa: microchip: Disable PTP function of KSZ8463
net: dsa: microchip: Setup fiber ports for KSZ8463
net: dsa: microchip: Write switch MAC address differently for KSZ8463
net: dsa: microchip: Use different registers for KSZ8463
net: dsa: microchip: Add KSZ8463 switch support to KSZ DSA driver
dt-bindings: net: dsa: microchip: Add KSZ8463 switch support
...
|
|
Fix typos in comments and error messages.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: David Arinzon <darinzon@amazon.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250723201528.2908218-1-helgaas@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In both the read callback for struct cyclecounter, and in struct
timecounter, struct cyclecounter is declared as a const pointer.
Unfortunatly, a number of users of this pointer treat it as a non-const
pointer as it is burried in a larger structure that is heavily modified by
the callback function when accessed. This lie had been hidden by the fact
that container_of() "casts away" a const attribute of a pointer without any
compiler warning happening at all.
Fix this all up by removing the const attribute in the needed places so
that everyone can see that the structure really isn't const, but can,
and is, modified by the users of it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/2025070124-backyard-hurt-783a@gregkh
|
|
Drivers that are using ops lock and don't depend on RTNL lock
still need to manage it because udp_tunnel's RTNL dependency.
Introduce new udp_tunnel_nic_lock and use it instead of
rtnl_lock. Drop non-UDP_TUNNEL_NIC_INFO_MAY_SLEEP mode from
udp_tunnel infra (udp_tunnel_nic_device_sync_work needs to
grab udp_tunnel_nic_lock mutex and might sleep).
Cover more places in v4:
- netlink
- udp_tunnel_notify_add_rx_port (ndo_open)
- triggers udp_tunnel_nic_device_sync_work
- udp_tunnel_notify_del_rx_port (ndo_stop)
- triggers udp_tunnel_nic_device_sync_work
- udp_tunnel_get_rx_info (__netdev_update_features)
- triggers NETDEV_UDP_TUNNEL_PUSH_INFO
- udp_tunnel_drop_rx_info (__netdev_update_features)
- triggers NETDEV_UDP_TUNNEL_DROP_INFO
- udp_tunnel_nic_reset_ntf (ndo_open)
- notifiers
- udp_tunnel_nic_netdevice_event, depending on the event:
- triggers NETDEV_UDP_TUNNEL_PUSH_INFO
- triggers NETDEV_UDP_TUNNEL_DROP_INFO
- ethnl_tunnel_info_reply_size
- udp_tunnel_nic_set_port_priv (two intel drivers)
Cc: Michael Chan <michael.chan@broadcom.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Stanislav Fomichev <stfomichev@gmail.com>
Link: https://patch.msgid.link/20250616162117.287806-4-stfomichev@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move this API to the canonical timer_*() namespace.
[ tglx: Redone against pre rc1 ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com
|
|
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Use the UIO_MEM_DMA_COHERENT type to properly handle mmap for
dma_alloc_coherent buffers.
The cnic l2_ring and l2_buf mmaps have caused page refcount issues as
the dma_alloc_coherent no longer provide __GFP_COMP allocation as per
commit "dma-mapping: reject __GFP_COMP in dma_alloc_attrs".
Fix this by having the uio device use dma_mmap_coherent.
The bnx2 and bnx2x status block allocations are also dma_alloc_coherent,
and should use dma_mmap_coherent. They don't allocate multiple pages,
but this interface does not work correctly with an iommu enabled unless
dma_mmap_coherent is used.
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Chris Leech <cleech@redhat.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20240201233400.3394996-3-cleech@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While injecting PCIe errors to the upstream PCIe switch of
a BCM57810 NIC, system hangs/crashes were observed.
After several calls to bnx2x_tx_timout() complete,
bnx2x_nic_unload() is called to free up HW resources
and bnx2x_napi_disable() is called to release NAPI objects.
Later, when the EEH driver calls bnx2x_io_slot_reset() to
complete the recovery process, bnx2x attempts to disable
NAPI again by calling bnx2x_napi_disable() and freeing
resources which have already been freed, resulting in a
hang or crash.
Introduce a new flag to track the HW resource and NAPI
allocation state, refactor duplicated code into a single
function, check page pool allocation status before freeing,
and reduces debug output when a TX timeout event occurs.
Reviewed-by: Manish Chopra <manishc@marvell.com>
Tested-by: Abdul Haleem <abdhalee@in.ibm.com>
Tested-by: David Christensen <drc@linux.vnet.ibm.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Venkata Sai Duggi <venkata.sai.duggi@ibm.com>
Signed-off-by: Thinh Tran <thinhtr@linux.vnet.ibm.com>
Link: https://lore.kernel.org/r/20230818161443.708785-2-thinhtr@linux.vnet.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the last step of the EEH recovery process, the EEH driver calls into
bnx2x_io_resume() to re-initialize the NIC hardware via the function
bnx2x_nic_load(). If an error occurs during bnx2x_nic_load(), OS and
hardware resources are released and an error code is returned to the
caller. When called from bnx2x_io_resume(), the return code is ignored
and the network interface is brought up unconditionally. Later attempts
to send a packet via this interface result in a page fault due to a null
pointer reference.
This patch checks the return code of bnx2x_nic_load(), prints an error
message if necessary, and does not enable the interface.
Signed-off-by: David Christensen <drc@linux.vnet.ibm.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux
Pull module updates from Luis Chamberlain:
"The summary of the changes for this pull requests is:
- Song Liu's new struct module_memory replacement
- Nick Alcock's MODULE_LICENSE() removal for non-modules
- My cleanups and enhancements to reduce the areas where we vmalloc
module memory for duplicates, and the respective debug code which
proves the remaining vmalloc pressure comes from userspace.
Most of the changes have been in linux-next for quite some time except
the minor fixes I made to check if a module was already loaded prior
to allocating the final module memory with vmalloc and the respective
debug code it introduces to help clarify the issue. Although the
functional change is small it is rather safe as it can only *help*
reduce vmalloc space for duplicates and is confirmed to fix a bootup
issue with over 400 CPUs with KASAN enabled. I don't expect stable
kernels to pick up that fix as the cleanups would have also had to
have been picked up. Folks on larger CPU systems with modules will
want to just upgrade if vmalloc space has been an issue on bootup.
Given the size of this request, here's some more elaborate details:
The functional change change in this pull request is the very first
patch from Song Liu which replaces the 'struct module_layout' with a
new 'struct module_memory'. The old data structure tried to put
together all types of supported module memory types in one data
structure, the new one abstracts the differences in memory types in a
module to allow each one to provide their own set of details. This
paves the way in the future so we can deal with them in a cleaner way.
If you look at changes they also provide a nice cleanup of how we
handle these different memory areas in a module. This change has been
in linux-next since before the merge window opened for v6.3 so to
provide more than a full kernel cycle of testing. It's a good thing as
quite a bit of fixes have been found for it.
Jason Baron then made dynamic debug a first class citizen module user
by using module notifier callbacks to allocate / remove module
specific dynamic debug information.
Nick Alcock has done quite a bit of work cross-tree to remove module
license tags from things which cannot possibly be module at my request
so to:
a) help him with his longer term tooling goals which require a
deterministic evaluation if a piece a symbol code could ever be
part of a module or not. But quite recently it is has been made
clear that tooling is not the only one that would benefit.
Disambiguating symbols also helps efforts such as live patching,
kprobes and BPF, but for other reasons and R&D on this area is
active with no clear solution in sight.
b) help us inch closer to the now generally accepted long term goal
of automating all the MODULE_LICENSE() tags from SPDX license tags
In so far as a) is concerned, although module license tags are a no-op
for non-modules, tools which would want create a mapping of possible
modules can only rely on the module license tag after the commit
8b41fc4454e ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf").
Nick has been working on this *for years* and AFAICT I was the only
one to suggest two alternatives to this approach for tooling. The
complexity in one of my suggested approaches lies in that we'd need a
possible-obj-m and a could-be-module which would check if the object
being built is part of any kconfig build which could ever lead to it
being part of a module, and if so define a new define
-DPOSSIBLE_MODULE [0].
A more obvious yet theoretical approach I've suggested would be to
have a tristate in kconfig imply the same new -DPOSSIBLE_MODULE as
well but that means getting kconfig symbol names mapping to modules
always, and I don't think that's the case today. I am not aware of
Nick or anyone exploring either of these options. Quite recently Josh
Poimboeuf has pointed out that live patching, kprobes and BPF would
benefit from resolving some part of the disambiguation as well but for
other reasons. The function granularity KASLR (fgkaslr) patches were
mentioned but Joe Lawrence has clarified this effort has been dropped
with no clear solution in sight [1].
In the meantime removing module license tags from code which could
never be modules is welcomed for both objectives mentioned above. Some
developers have also welcomed these changes as it has helped clarify
when a module was never possible and they forgot to clean this up, and
so you'll see quite a bit of Nick's patches in other pull requests for
this merge window. I just picked up the stragglers after rc3. LWN has
good coverage on the motivation behind this work [2] and the typical
cross-tree issues he ran into along the way. The only concrete blocker
issue he ran into was that we should not remove the MODULE_LICENSE()
tags from files which have no SPDX tags yet, even if they can never be
modules. Nick ended up giving up on his efforts due to having to do
this vetting and backlash he ran into from folks who really did *not
understand* the core of the issue nor were providing any alternative /
guidance. I've gone through his changes and dropped the patches which
dropped the module license tags where an SPDX license tag was missing,
it only consisted of 11 drivers. To see if a pull request deals with a
file which lacks SPDX tags you can just use:
./scripts/spdxcheck.py -f \
$(git diff --name-only commid-id | xargs echo)
You'll see a core module file in this pull request for the above, but
that's not related to his changes. WE just need to add the SPDX
license tag for the kernel/module/kmod.c file in the future but it
demonstrates the effectiveness of the script.
Most of Nick's changes were spread out through different trees, and I
just picked up the slack after rc3 for the last kernel was out. Those
changes have been in linux-next for over two weeks.
The cleanups, debug code I added and final fix I added for modules
were motivated by David Hildenbrand's report of boot failing on a
systems with over 400 CPUs when KASAN was enabled due to running out
of virtual memory space. Although the functional change only consists
of 3 lines in the patch "module: avoid allocation if module is already
present and ready", proving that this was the best we can do on the
modules side took quite a bit of effort and new debug code.
The initial cleanups I did on the modules side of things has been in
linux-next since around rc3 of the last kernel, the actual final fix
for and debug code however have only been in linux-next for about a
week or so but I think it is worth getting that code in for this merge
window as it does help fix / prove / evaluate the issues reported with
larger number of CPUs. Userspace is not yet fixed as it is taking a
bit of time for folks to understand the crux of the issue and find a
proper resolution. Worst come to worst, I have a kludge-of-concept [3]
of how to make kernel_read*() calls for modules unique / converge
them, but I'm currently inclined to just see if userspace can fix this
instead"
Link: https://lore.kernel.org/all/Y/kXDqW+7d71C4wz@bombadil.infradead.org/ [0]
Link: https://lkml.kernel.org/r/025f2151-ce7c-5630-9b90-98742c97ac65@redhat.com [1]
Link: https://lwn.net/Articles/927569/ [2]
Link: https://lkml.kernel.org/r/20230414052840.1994456-3-mcgrof@kernel.org [3]
* tag 'modules-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux: (121 commits)
module: add debugging auto-load duplicate module support
module: stats: fix invalid_mod_bytes typo
module: remove use of uninitialized variable len
module: fix building stats for 32-bit targets
module: stats: include uapi/linux/module.h
module: avoid allocation if module is already present and ready
module: add debug stats to help identify memory pressure
module: extract patient module check into helper
modules/kmod: replace implementation with a semaphore
Change DEFINE_SEMAPHORE() to take a number argument
module: fix kmemleak annotations for non init ELF sections
module: Ignore L0 and rename is_arm_mapping_symbol()
module: Move is_arm_mapping_symbol() to module_symbol.h
module: Sync code of is_arm_mapping_symbol()
scripts/gdb: use mem instead of core_layout to get the module address
interconnect: remove module-related code
interconnect: remove MODULE_LICENSE in non-modules
zswap: remove MODULE_LICENSE in non-modules
zpool: remove MODULE_LICENSE in non-modules
x86/mm/dump_pagetables: remove MODULE_LICENSE in non-modules
...
|
|
Fundamentally semaphores are a counted primitive, but
DEFINE_SEMAPHORE() does not expose this and explicitly creates a
binary semaphore.
Change DEFINE_SEMAPHORE() to take a number argument and use that in the
few places that open-coded it using __SEMAPHORE_INITIALIZER().
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
[mcgrof: add some tribal knowledge about why some folks prefer
binary sempahores over mutexes]
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
|
|
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f54 ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ariel Elior <aelior@marvell.com>
Cc: Sudarsana Kalluru <skalluru@marvell.com>
Cc: Manish Chopra <manishc@marvell.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert all remaining drivers that still use .adjfreq to the newer .adjfine
implementation. These drivers are not straightforward, as they use
non-standard methods of programming their hardware. They are all converted
to use scaled_ppm_to_ppb to get the parts per billion value that their
logic depends on.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Ariel Elior <aelior@marvell.com>
Cc: Sudarsana Kalluru <skalluru@marvell.com>
Cc: Manish Chopra <manishc@marvell.com>
Cc: Derek Chickles <dchickles@marvell.com>
Cc: Satanand Burla <sburla@marvell.com>
Cc: Felix Manlunas <fmanlunas@marvell.com>
Cc: Raju Rangoju <rajur@chelsio.com>
Cc: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: Edward Cree <ecree.xilinx@gmail.com>
Cc: Martin Habets <habetsm.xilinx@gmail.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.
Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # For drivers/net/ethernet/mellanox/mlxsw
Acked-by: Geoff Levand <geoff@infradead.org> # For ps3_gelic_net and spider_net_ethtool
Acked-by: Tom Lendacky <thomas.lendacky@amd.com> # For drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c
Acked-by: Marcin Wojtas <mw@semihalf.com> # For drivers/net/ethernet/marvell/mvpp2
Reviewed-by: Leon Romanovsky <leonro@nvidia.com> # For drivers/net/ethernet/mellanox/mlx{4|5}
Reviewed-by: Shay Agroskin <shayagr@amazon.com> # For drivers/net/ethernet/amazon/ena
Acked-by: Krzysztof Hałasa <khalasa@piap.pl> # For IXP4xx Ethernet
Link: https://lore.kernel.org/r/20220830201457.7984-3-wsa+renesas@sang-engineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
While handling PCI errors (AER flow) driver tries to
disable NAPI [napi_disable()] after NAPI is deleted
[__netif_napi_del()] which causes unexpected system
hang/crash.
System message log shows the following:
=======================================
[ 3222.537510] EEH: Detected PCI bus error on PHB#384-PE#800000 [ 3222.537511] EEH: This PCI device has failed 2 times in the last hour and will be permanently disabled after 5 failures.
[ 3222.537512] EEH: Notify device drivers to shutdown [ 3222.537513] EEH: Beginning: 'error_detected(IO frozen)'
[ 3222.537514] EEH: PE#800000 (PCI 0384:80:00.0): Invoking
bnx2x->error_detected(IO frozen)
[ 3222.537516] bnx2x: [bnx2x_io_error_detected:14236(eth14)]IO error detected [ 3222.537650] EEH: PE#800000 (PCI 0384:80:00.0): bnx2x driver reports:
'need reset'
[ 3222.537651] EEH: PE#800000 (PCI 0384:80:00.1): Invoking
bnx2x->error_detected(IO frozen)
[ 3222.537651] bnx2x: [bnx2x_io_error_detected:14236(eth13)]IO error detected [ 3222.537729] EEH: PE#800000 (PCI 0384:80:00.1): bnx2x driver reports:
'need reset'
[ 3222.537729] EEH: Finished:'error_detected(IO frozen)' with aggregate recovery state:'need reset'
[ 3222.537890] EEH: Collect temporary log [ 3222.583481] EEH: of node=0384:80:00.0 [ 3222.583519] EEH: PCI device/vendor: 168e14e4 [ 3222.583557] EEH: PCI cmd/status register: 00100140 [ 3222.583557] EEH: PCI-E capabilities and status follow:
[ 3222.583744] EEH: PCI-E 00: 00020010 012c8da2 00095d5e 00455c82 [ 3222.583892] EEH: PCI-E 10: 10820000 00000000 00000000 00000000 [ 3222.583893] EEH: PCI-E 20: 00000000 [ 3222.583893] EEH: PCI-E AER capability register set follows:
[ 3222.584079] EEH: PCI-E AER 00: 13c10001 00000000 00000000 00062030 [ 3222.584230] EEH: PCI-E AER 10: 00002000 000031c0 000001e0 00000000 [ 3222.584378] EEH: PCI-E AER 20: 00000000 00000000 00000000 00000000 [ 3222.584416] EEH: PCI-E AER 30: 00000000 00000000 [ 3222.584416] EEH: of node=0384:80:00.1 [ 3222.584454] EEH: PCI device/vendor: 168e14e4 [ 3222.584491] EEH: PCI cmd/status register: 00100140 [ 3222.584492] EEH: PCI-E capabilities and status follow:
[ 3222.584677] EEH: PCI-E 00: 00020010 012c8da2 00095d5e 00455c82 [ 3222.584825] EEH: PCI-E 10: 10820000 00000000 00000000 00000000 [ 3222.584826] EEH: PCI-E 20: 00000000 [ 3222.584826] EEH: PCI-E AER capability register set follows:
[ 3222.585011] EEH: PCI-E AER 00: 13c10001 00000000 00000000 00062030 [ 3222.585160] EEH: PCI-E AER 10: 00002000 000031c0 000001e0 00000000 [ 3222.585309] EEH: PCI-E AER 20: 00000000 00000000 00000000 00000000 [ 3222.585347] EEH: PCI-E AER 30: 00000000 00000000 [ 3222.586872] RTAS: event: 5, Type: Platform Error (224), Severity: 2 [ 3222.586873] EEH: Reset without hotplug activity [ 3224.762767] EEH: Beginning: 'slot_reset'
[ 3224.762770] EEH: PE#800000 (PCI 0384:80:00.0): Invoking
bnx2x->slot_reset()
[ 3224.762771] bnx2x: [bnx2x_io_slot_reset:14271(eth14)]IO slot reset initializing...
[ 3224.762887] bnx2x 0384:80:00.0: enabling device (0140 -> 0142) [ 3224.768157] bnx2x: [bnx2x_io_slot_reset:14287(eth14)]IO slot reset
--> driver unload
Uninterruptible tasks
=====================
crash> ps | grep UN
213 2 11 c000000004c89e00 UN 0.0 0 0 [eehd]
215 2 0 c000000004c80000 UN 0.0 0 0
[kworker/0:2]
2196 1 28 c000000004504f00 UN 0.1 15936 11136 wickedd
4287 1 9 c00000020d076800 UN 0.0 4032 3008 agetty
4289 1 20 c00000020d056680 UN 0.0 7232 3840 agetty
32423 2 26 c00000020038c580 UN 0.0 0 0
[kworker/26:3]
32871 4241 27 c0000002609ddd00 UN 0.1 18624 11648 sshd
32920 10130 16 c00000027284a100 UN 0.1 48512 12608 sendmail
33092 32987 0 c000000205218b00 UN 0.1 48512 12608 sendmail
33154 4567 16 c000000260e51780 UN 0.1 48832 12864 pickup
33209 4241 36 c000000270cb6500 UN 0.1 18624 11712 sshd
33473 33283 0 c000000205211480 UN 0.1 48512 12672 sendmail
33531 4241 37 c00000023c902780 UN 0.1 18624 11648 sshd
EEH handler hung while bnx2x sleeping and holding RTNL lock
===========================================================
crash> bt 213
PID: 213 TASK: c000000004c89e00 CPU: 11 COMMAND: "eehd"
#0 [c000000004d477e0] __schedule at c000000000c70808
#1 [c000000004d478b0] schedule at c000000000c70ee0
#2 [c000000004d478e0] schedule_timeout at c000000000c76dec
#3 [c000000004d479c0] msleep at c0000000002120cc
#4 [c000000004d479f0] napi_disable at c000000000a06448
^^^^^^^^^^^^^^^^
#5 [c000000004d47a30] bnx2x_netif_stop at c0080000018dba94 [bnx2x]
#6 [c000000004d47a60] bnx2x_io_slot_reset at c0080000018a551c [bnx2x]
#7 [c000000004d47b20] eeh_report_reset at c00000000004c9bc
#8 [c000000004d47b90] eeh_pe_report at c00000000004d1a8
#9 [c000000004d47c40] eeh_handle_normal_event at c00000000004da64
And the sleeping source code
============================
crash> dis -ls c000000000a06448
FILE: ../net/core/dev.c
LINE: 6702
6697 {
6698 might_sleep();
6699 set_bit(NAPI_STATE_DISABLE, &n->state);
6700
6701 while (test_and_set_bit(NAPI_STATE_SCHED, &n->state))
* 6702 msleep(1);
6703 while (test_and_set_bit(NAPI_STATE_NPSVC, &n->state))
6704 msleep(1);
6705
6706 hrtimer_cancel(&n->timer);
6707
6708 clear_bit(NAPI_STATE_DISABLE, &n->state);
6709 }
EEH calls into bnx2x twice based on the system log above, first through
bnx2x_io_error_detected() and then bnx2x_io_slot_reset(), and executes
the following call chains:
bnx2x_io_error_detected()
+-> bnx2x_eeh_nic_unload()
+-> bnx2x_del_all_napi()
+-> __netif_napi_del()
bnx2x_io_slot_reset()
+-> bnx2x_netif_stop()
+-> bnx2x_napi_disable()
+->napi_disable()
Fix this by correcting the sequence of NAPI APIs usage,
that is delete the NAPI after disabling it.
Fixes: 7fa6f34081f1 ("bnx2x: AER revised")
Reported-by: David Christensen <drc@linux.vnet.ibm.com>
Tested-by: David Christensen <drc@linux.vnet.ibm.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220426153913.6966-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
added request_firmware() logic in probe() which caused
load failure when firmware file is not present in initrd (below),
as access to firmware file is not feasible during probe.
Direct firmware load for bnx2x/bnx2x-e2-7.13.15.0.fw failed with error -2
Direct firmware load for bnx2x/bnx2x-e2-7.13.21.0.fw failed with error -2
This patch fixes this issue by -
1. Removing request_firmware() logic from the probe()
such that .ndo_open() handle it as it used to handle
it earlier
2. Given request_firmware() is removed from probe(), so
driver has to relax FW version comparisons a bit against
the already loaded FW version (by some other PFs of same
adapter) to allow different compatible/close enough FWs with which
multiple PFs may run with (in different environments), as the
given PF who is in probe flow has no idea now with which firmware
file version it is going to initialize the device in ndo_open()
Link: https://lore.kernel.org/all/46f2d9d9-ae7f-b332-ddeb-b59802be2bab@molgen.mpg.de/
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Fixes: b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220316214613.6884-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0") added
new firmware support in the driver with maintaining older firmware
compatibility. However, older firmware was not added in MODULE_FIRMWARE()
which caused missing firmware files in initrd image leading to driver load
failure from initrd. This patch adds MODULE_FIRMWARE() for older firmware
version to have firmware files included in initrd.
Fixes: b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215627
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Link: https://lore.kernel.org/r/20220223085720.12021-1-manishc@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
Moreover, dma_set_mask_and_coherent() returns 0 or -EIO, so the return
code of the function can be used directly.
Finally, inline bnx2x_set_coherency_mask() because it is now only a wrapper
for a single dma_set_mask_and_coherent() call.
Simplify code and remove some dead code accordingly.
[1]: https://lkml.org/lkml/2021/6/7/398
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/29608a525876afddceabf8f11b2ba606da8748fc.1641730747.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This new firmware addresses few important issues and enhancements
as mentioned below -
- Support direct invalidation of FP HSI Ver per function ID, required for
invalidating FP HSI Ver prior to each VF start, as there is no VF start
- BRB hardware block parity error detection support for the driver
- Fix the FCOE underrun flow
- Fix PSOD during FCoE BFS over the NIC ports after preboot driver
- Maintains backward compatibility
This patch incorporates this new firmware 7.13.21.0 in bnx2x driver.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 94dd016ae538 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP
ioctl to active device") the user could get bond active interface's
PHC index directly. But when there is a failover, the bond active
interface will change, thus the PHC index is also changed. This may
break the user's program if they did not update the PHC timely.
This patch adds a new hwtstamp_config flag HWTSTAMP_FLAG_BONDED_PHC_INDEX.
When the user wants to get the bond active interface's PHC, they need to
add this flag and be aware the PHC index may be changed.
With the new flag. All flag checks in current drivers are removed. Only
the checking in net_hwtstamp_validate() is kept.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This big patch sprinkles const on local variables and
function arguments which may refer to netdev->dev_addr.
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Some of the changes here are not strictly required - const
is sometimes cast off but pointer is not used for writing.
It seems like it's still better to add the const in case
the code changes later or relevant -W flags get enabled
for the build.
No functional changes.
Link: https://lore.kernel.org/r/20211014142432.449314-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert all Ethernet drivers from memcpy(... ETH_ADDR)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, ETH_ALEN)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Convert controller drivers to generic_handle_domain_irq() (Marc
Zyngier)
- Simplify VPD (Vital Product Data) access and search (Heiner
Kallweit)
- Update bnx2, bnx2x, bnxt, cxgb4, cxlflash, sfc, tg3 drivers to use
simplified VPD interfaces (Heiner Kallweit)
- Run Max Payload Size quirks before configuring MPS; work around
ASMedia ASM1062 SATA MPS issue (Marek Behún)
Resource management:
- Refactor pci_ioremap_bar() and pci_ioremap_wc_bar() (Krzysztof
Wilczyński)
- Optimize pci_resource_len() to reduce kernel size (Zhen Lei)
PCI device hotplug:
- Fix a double unmap in ibmphp (Vishal Aslot)
PCIe port driver:
- Enable Bandwidth Notification only if port supports it (Stuart
Hayes)
Sysfs/proc/syscalls:
- Add schedule point in proc_bus_pci_read() (Krzysztof Wilczyński)
- Return ~0 data on pciconfig_read() CAP_SYS_ADMIN failure (Krzysztof
Wilczyński)
- Return "int" from pciconfig_read() syscall (Krzysztof Wilczyński)
Virtualization:
- Extend "pci=noats" to also turn on Translation Blocking to protect
against some DMA attacks (Alex Williamson)
- Add sysfs mechanism to control the type of reset used between
device assignments to VMs (Amey Narkhede)
- Add support for ACPI _RST reset method (Shanker Donthineni)
- Add ACS quirks for Cavium multi-function devices (George Cherian)
- Add ACS quirks for NXP LX2xx0 and LX2xx2 platforms (Wasim Khan)
- Allow HiSilicon AMBA devices that appear as fake PCI devices to use
PASID and SVA (Zhangfei Gao)
Endpoint framework:
- Add support for SR-IOV Endpoint devices (Kishon Vijay Abraham I)
- Zero-initialize endpoint test tool parameters so we don't use
random parameters (Shunyong Yang)
APM X-Gene PCIe controller driver:
- Remove redundant dev_err() call in xgene_msi_probe() (ErKun Yang)
Broadcom iProc PCIe controller driver:
- Don't fail devm_pci_alloc_host_bridge() on missing 'ranges' because
it's optional on BCMA devices (Rob Herring)
- Fix BCMA probe resource handling (Rob Herring)
Cadence PCIe driver:
- Work around J7200 Link training electrical issue by increasing
delays in LTSSM (Nadeem Athani)
Intel IXP4xx PCI controller driver:
- Depend on ARCH_IXP4XX to avoid useless config questions (Geert
Uytterhoeven)
Intel Keembay PCIe controller driver:
- Add Intel Keem Bay PCIe controller (Srikanth Thokala)
Marvell Aardvark PCIe controller driver:
- Work around config space completion handling issues (Evan Wang)
- Increase timeout for config access completions (Pali Rohár)
- Emulate CRS Software Visibility bit (Pali Rohár)
- Configure resources from DT 'ranges' property to fix I/O space
access (Pali Rohár)
- Serialize INTx mask/unmask (Pali Rohár)
MediaTek PCIe controller driver:
- Add MT7629 support in DT (Chuanjia Liu)
- Fix an MSI issue (Chuanjia Liu)
- Get syscon regmap ("mediatek,generic-pciecfg"), IRQ number
("pci_irq"), PCI domain ("linux,pci-domain") from DT properties if
present (Chuanjia Liu)
Microsoft Hyper-V host bridge driver:
- Add ARM64 support (Boqun Feng)
- Support "Create Interrupt v3" message (Sunil Muthuswamy)
NVIDIA Tegra PCIe controller driver:
- Use seq_puts(), move err_msg from stack to static, fix OF node leak
(Christophe JAILLET)
NVIDIA Tegra194 PCIe driver:
- Disable suspend when in Endpoint mode (Om Prakash Singh)
- Fix MSI-X address programming error (Om Prakash Singh)
- Disable interrupts during suspend to avoid spurious AER link down
(Om Prakash Singh)
Renesas R-Car PCIe controller driver:
- Work around hardware issue that prevents Link L1->L0 transition
(Marek Vasut)
- Fix runtime PM refcount leak (Dinghao Liu)
Rockchip DesignWare PCIe controller driver:
- Add Rockchip RK356X host controller driver (Simon Xue)
TI J721E PCIe driver:
- Add support for J7200 and AM64 (Kishon Vijay Abraham I)
Toshiba Visconti PCIe controller driver:
- Add Toshiba Visconti PCIe host controller driver (Nobuhiro
Iwamatsu)
Xilinx NWL PCIe controller driver:
- Enable PCIe reference clock via CCF (Hyun Kwon)
Miscellaneous:
- Convert sta2x11 from 'pci_' to 'dma_' API (Christophe JAILLET)
- Fix pci_dev_str_match_path() alloc while atomic bug (used for
kernel parameters that specify devices) (Dan Carpenter)
- Remove pointless Precision Time Management warning when PTM is
present but not enabled (Jakub Kicinski)
- Remove surplus "break" statements (Krzysztof Wilczyński)"
* tag 'pci-v5.15-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (132 commits)
PCI: ibmphp: Fix double unmap of io_mem
x86/PCI: sta2x11: switch from 'pci_' to 'dma_' API
PCI/VPD: Use unaligned access helpers
PCI/VPD: Clean up public VPD defines and inline functions
cxgb4: Use pci_vpd_find_id_string() to find VPD ID string
PCI/VPD: Add pci_vpd_find_id_string()
PCI/VPD: Include post-processing in pci_vpd_find_tag()
PCI/VPD: Stop exporting pci_vpd_find_info_keyword()
PCI/VPD: Stop exporting pci_vpd_find_tag()
PCI: Set dma-can-stall for HiSilicon chips
PCI: rockchip-dwc: Add Rockchip RK356X host controller driver
PCI: dwc: Remove surplus break statement after return
PCI: artpec6: Remove local code block from switch statement
PCI: artpec6: Remove surplus break statement after return
MAINTAINERS: Add entries for Toshiba Visconti PCIe controller
PCI: visconti: Add Toshiba Visconti PCIe host controller driver
PCI/portdrv: Enable Bandwidth Notification only if port supports it
PCI: Allow PASID on fake PCIe devices without TLP prefixes
PCI: mediatek: Use PCI domain to handle ports detection
PCI: mediatek: Add new method to get irq number
...
|
|
Use pci_vpd_find_ro_info_keyword() to search for keywords in VPD to
simplify the code.
Use strncasecmp() to match Vendor ID instead of comparing with lower- and
upper-case hex string.
[bhelgaas: convert to strncasecmp()]
Link: https://lore.kernel.org/r/a9f730cf-e31e-902b-7b39-0ff2e99636e0@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Use pci_vpd_alloc() to dynamically allocate a properly sized buffer and
read the full VPD data into it.
This simplifies the code, and we no longer have to make assumptions about
VPD size.
Link: https://lore.kernel.org/r/821a334d-ff9d-386e-5f42-9b620ab3dbfa@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
This reverts commit bed3db3d734e8e55815d865913ef75d9f707db96.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit da417885a99d36036cc7d2778f94b846e6582434.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use pci_vpd_find_ro_info_keyword() to search for keywords in VPD to
simplify the code.
str_id_reg and str_id_cap hold the same string and are used in the same
comparison. This doesn't make sense, use one string str_id instead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use pci_vpd_alloc() to dynamically allocate a properly sized buffer and
read the full VPD data into it.
This simplifies the code, and we no longer have to make assumptions about
VPD size.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:13595: warning: expecting prototype for bnx2x_get_num_none_def_sbs(). Prototype was for bnx2x_get_num_non_def_sbs() instead
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.c:4165: warning: expecting prototype for atomic_add_ifless(). Prototype was for __atomic_add_ifless() instead
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.c:4193: warning: expecting prototype for atomic_dec_ifmoe(). Prototype was for __atomic_dec_ifmoe() instead
Cc: Ariel Elior <aelior@marvell.com>
Cc: Sudarsana Kalluru <skalluru@marvell.com>
Cc: GR-everest-linux-l2@marvell.com
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Release OF node when pci_scan_device() fails (Dmitry Baryshkov)
- Add pci_disable_parity() (Bjorn Helgaas)
- Disable Mellanox Tavor parity reporting (Heiner Kallweit)
- Disable N2100 r8169 parity reporting (Heiner Kallweit)
- Fix RCiEP device to RCEC association (Qiuxu Zhuo)
- Convert sysfs "config", "rom", "reset", "label", "index",
"acpi_index" to static attributes to help fix races in device
enumeration (Krzysztof Wilczyński)
- Convert sysfs "vpd" to static attribute (Heiner Kallweit, Krzysztof
Wilczyński)
- Use sysfs_emit() in "show" functions (Krzysztof Wilczyński)
- Remove unused alloc_pci_root_info() return value (Krzysztof
Wilczyński)
PCI device hotplug:
- Fix acpiphp reference count leak (Feilong Lin)
Power management:
- Fix acpi_pci_set_power_state() debug message (Rafael J. Wysocki)
- Fix runtime PM imbalance (Dinghao Liu)
Virtualization:
- Increase delay after FLR to work around Intel DC P4510 NVMe erratum
(Raphael Norwitz)
MSI:
- Convert rcar, tegra, xilinx to MSI domains (Marc Zyngier)
- For rcar, xilinx, use controller address as MSI doorbell (Marc
Zyngier)
- Remove unused hv msi_controller struct (Marc Zyngier)
- Remove unused PCI core msi_controller support (Marc Zyngier)
- Remove struct msi_controller altogether (Marc Zyngier)
- Remove unused default_teardown_msi_irqs() (Marc Zyngier)
- Let host bridges declare their reliance on MSI domains (Marc
Zyngier)
- Make pci_host_common_probe() declare its reliance on MSI domains
(Marc Zyngier)
- Advertise mediatek lack of built-in MSI handling (Thomas Gleixner)
- Document ways of ending up with NO_MSI (Marc Zyngier)
- Refactor HT advertising of NO_MSI flag (Marc Zyngier)
VPD:
- Remove obsolete Broadcom NIC VPD length-limiting quirk (Heiner
Kallweit)
- Remove sysfs VPD size checking dead code (Heiner Kallweit)
- Convert VPF sysfs file to static attribute (Heiner Kallweit)
- Remove unnecessary pci_set_vpd_size() (Heiner Kallweit)
- Tone down "missing VPD" message (Heiner Kallweit)
Endpoint framework:
- Fix NULL pointer dereference when epc_features not implemented
(Shradha Todi)
- Add missing destroy_workqueue() in endpoint test (Yang Yingliang)
Amazon Annapurna Labs PCIe controller driver:
- Fix compile testing without CONFIG_PCI_ECAM (Arnd Bergmann)
- Fix "no symbols" warnings when compile testing with
CONFIG_TRIM_UNUSED_KSYMS (Arnd Bergmann)
APM X-Gene PCIe controller driver:
- Fix cfg resource mapping regression (Dejin Zheng)
Broadcom iProc PCIe controller driver:
- Return zero for success of iproc_msi_irq_domain_alloc() (Pali
Rohár)
Broadcom STB PCIe controller driver:
- Add reset_control_rearm() stub for !CONFIG_RESET_CONTROLLER (Jim
Quinlan)
- Fix use of BCM7216 reset controller (Jim Quinlan)
- Use reset/rearm for Broadcom STB pulse reset instead of
deassert/assert (Jim Quinlan)
- Fix brcm_pcie_probe() error return for unsupported revision (Wei
Yongjun)
Cavium ThunderX PCIe controller driver:
- Fix compile testing (Arnd Bergmann)
- Fix "no symbols" warnings when compile testing with
CONFIG_TRIM_UNUSED_KSYMS (Arnd Bergmann)
Freescale Layerscape PCIe controller driver:
- Fix ls_pcie_ep_probe() syntax error (comma for semicolon)
(Krzysztof Wilczyński)
- Remove layerscape-gen4 dependencies on OF and ARM64, add dependency
on ARCH_LAYERSCAPE (Geert Uytterhoeven)
HiSilicon HIP PCIe controller driver:
- Remove obsolete HiSilicon PCIe DT description (Dongdong Liu)
Intel Gateway PCIe controller driver:
- Remove unused pcie_app_rd() (Jiapeng Chong)
Intel VMD host bridge driver:
- Program IRTE with Requester ID of VMD endpoint, not child device
(Jon Derrick)
- Disable VMD MSI-X remapping when possible so children can use more
MSI-X vectors (Jon Derrick)
MediaTek PCIe controller driver:
- Configure FC and FTS for functions other than 0 (Ryder Lee)
- Add YAML schema for MediaTek (Jianjun Wang)
- Export pci_pio_to_address() for module use (Jianjun Wang)
- Add MediaTek MT8192 PCIe controller driver (Jianjun Wang)
- Add MediaTek MT8192 INTx support (Jianjun Wang)
- Add MediaTek MT8192 MSI support (Jianjun Wang)
- Add MediaTek MT8192 system power management support (Jianjun Wang)
- Add missing MODULE_DEVICE_TABLE (Qiheng Lin)
Microchip PolarFlare PCIe controller driver:
- Make several symbols static (Wei Yongjun)
NVIDIA Tegra PCIe controller driver:
- Add MCFG quirks for Tegra194 ECAM errata (Vidya Sagar)
- Make several symbols const (Rikard Falkeborn)
- Fix Kconfig host/endpoint typo (Wesley Sheng)
SiFive FU740 PCIe controller driver:
- Add pcie_aux clock to prci driver (Greentime Hu)
- Use reset-simple in prci driver for PCIe (Greentime Hu)
- Add SiFive FU740 PCIe host controller driver and DT binding (Paul
Walmsley, Greentime Hu)
Synopsys DesignWare PCIe controller driver:
- Move MSI Receiver init to dw_pcie_host_init() so it is
re-initialized along with the RC in resume (Jisheng Zhang)
- Move iATU detection earlier to fix regression (Hou Zhiqiang)
TI J721E PCIe driver:
- Add DT binding and TI j721e support for refclk to PCIe connector
(Kishon Vijay Abraham I)
- Add host mode and endpoint mode DT bindings for TI AM64 SoC (Kishon
Vijay Abraham I)
TI Keystone PCIe controller driver:
- Use generic config accessors for TI AM65x (K3) to fix regression
(Kishon Vijay Abraham I)
Xilinx NWL PCIe controller driver:
- Add support for coherent PCIe DMA traffic using CCI (Bharat Kumar
Gogada)
- Add optional "dma-coherent" DT property (Bharat Kumar Gogada)
Miscellaneous:
- Fix kernel-doc warnings (Krzysztof Wilczyński)
- Remove unused MicroGate SyncLink device IDs (Jiri Slaby)
- Remove redundant dev_err() for devm_ioremap_resource() failure
(Chen Hui)
- Remove redundant initialization (Colin Ian King)
- Drop redundant dev_err() for platform_get_irq() errors (Krzysztof
Wilczyński)"
* tag 'pci-v5.13-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (98 commits)
riscv: dts: Add PCIe support for the SiFive FU740-C000 SoC
PCI: fu740: Add SiFive FU740 PCIe host controller driver
dt-bindings: PCI: Add SiFive FU740 PCIe host controller
MAINTAINERS: Add maintainers for SiFive FU740 PCIe driver
clk: sifive: Use reset-simple in prci driver for PCIe driver
clk: sifive: Add pcie_aux clock in prci driver for PCIe driver
PCI: brcmstb: Use reset/rearm instead of deassert/assert
ata: ahci_brcm: Fix use of BCM7216 reset controller
reset: add missing empty function reset_control_rearm()
PCI: Allow VPD access for QLogic ISP2722
PCI/VPD: Add helper pci_get_func0_dev()
PCI/VPD: Remove pci_vpd_find_tag() SRDT handling
PCI/VPD: Remove pci_vpd_find_tag() 'offset' argument
PCI/VPD: Change pci_vpd_init() return type to void
PCI/VPD: Make missing VPD message less alarming
PCI/VPD: Remove pci_set_vpd_size()
x86/PCI: Remove unused alloc_pci_root_info() return value
MAINTAINERS: Add Jianjun Wang as MediaTek PCI co-maintainer
PCI: mediatek-gen3: Add system PM support
PCI: mediatek-gen3: Add MSI support
...
|
|
All callers pass 0 as offset. Therefore remove the parameter and use a
fixed offset 0 in pci_vpd_find_tag().
Link: https://lore.kernel.org/r/f62e6e19-5423-2ead-b2bd-62844b23ef8f@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
remove unneeded variable: "ret".
Signed-off-by: dingsenjie <dingsenjie@yulong.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All UDP tunnel port management is now routed via udp_tunnel_nic
infra directly. Remove the old callbacks.
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Replace /* no break */ comments with the new pseudo-keyword macro
fallthrough[1].
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As part of the W=1 cleanups for ethernet, a million [*] driver
comments had to be cleaned up to get the W=1 compilation to
succeed. This change finally makes the drivers/net/ethernet tree
compile with W=1 set on the command line. NOTE: The kernel uses
kdoc style (see Documentation/process/kernel-doc.rst) when
documenting code, not doxygen or other styles.
After this patch the x86_64 build has no warnings from W=1, however
scripts/kernel-doc says there are 1545 more warnings in source files, that
I need to develop a script to fix in a followup patch.
The errors fixed here are all kdoc of a few classes, with a few outliers:
In file included from drivers/net/ethernet/qlogic/netxen/netxen_nic_hw.c:10:
drivers/net/ethernet/qlogic/netxen/netxen_nic.h:1193:18: warning: ‘FW_DUMP_LEVELS’ defined but not used [-Wunused-const-variable=]
1193 | static const u32 FW_DUMP_LEVELS[] = { 0x3, 0x7, 0xf, 0x1f, 0x3f, 0x7f, 0xff };
| ^~~~~~~~~~~~~~
... repeats 4 times...
drivers/net/ethernet/sun/cassini.c:2084:24: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
2084 | RX_USED_ADD(page, i);
drivers/net/ethernet/natsemi/ns83820.c: In function ‘phy_intr’:
drivers/net/ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable]
603 | u32 tbisr, tanar, tanlpar;
| ^~~~~
drivers/net/ethernet/natsemi/ns83820.c: In function ‘ns83820_get_link_ksettings’:
drivers/net/ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable]
1207 | u32 cfg, tanar, tbicr;
| ^~~~~
drivers/net/ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable]
1063 | int data_size, yf_size;
| ^~~~~~~
Normal kdoc fixes:
warning: Function parameter or member 'x' not described in 'y'
warning: Excess function parameter 'x' description in 'y'
warning: Cannot understand <string> on line <NNN> - I thought it was a doc line
[*] - ok it wasn't quite a million, but it felt like it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This addresses the following coccinelle warning:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:15415:1-26: WARNING:
Assignment of 0/1 to bool variable
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:12393:2-17: WARNING:
Assignment of 0/1 to bool variable
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:15497:2-27: WARNING:
Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
Fairly straightforward conversion - no need to keep track
of the use count, and replay when ports get removed, also
callbacks can just sleep.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch adds driver changes to perform Idlechk dump during the debug
data collection.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch populates a database of idlechk tests (registers and
predicates) and performs the idlechk using this data.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With legacy PM, drivers themselves were responsible for managing the
device's power states and takes care of register states.
After upgrading to the generic structure, PCI core will take care of
required tasks and drivers should do only device-specific operations.
The driver was also calling bnx2x_set_power_state() to set the power state
of the device by changing the device's registers' value. It is no more
needed.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Acked-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use linux kernel version for ethtool and module versions.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking updates from David Miller:
1) Add WireGuard
2) Add HE and TWT support to ath11k driver, from John Crispin.
3) Add ESP in TCP encapsulation support, from Sabrina Dubroca.
4) Add variable window congestion control to TIPC, from Jon Maloy.
5) Add BCM84881 PHY driver, from Russell King.
6) Start adding netlink support for ethtool operations, from Michal
Kubecek.
7) Add XDP drop and TX action support to ena driver, from Sameeh
Jubran.
8) Add new ipv4 route notifications so that mlxsw driver does not have
to handle identical routes itself. From Ido Schimmel.
9) Add BPF dynamic program extensions, from Alexei Starovoitov.
10) Support RX and TX timestamping in igc, from Vinicius Costa Gomes.
11) Add support for macsec HW offloading, from Antoine Tenart.
12) Add initial support for MPTCP protocol, from Christoph Paasch,
Matthieu Baerts, Florian Westphal, Peter Krystad, and many others.
13) Add Octeontx2 PF support, from Sunil Goutham, Geetha sowjanya, Linu
Cherian, and others.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1469 commits)
net: phy: add default ARCH_BCM_IPROC for MDIO_BCM_IPROC
udp: segment looped gso packets correctly
netem: change mailing list
qed: FW 8.42.2.0 debug features
qed: rt init valid initialization changed
qed: Debug feature: ilt and mdump
qed: FW 8.42.2.0 Add fw overlay feature
qed: FW 8.42.2.0 HSI changes
qed: FW 8.42.2.0 iscsi/fcoe changes
qed: Add abstraction for different hsi values per chip
qed: FW 8.42.2.0 Additional ll2 type
qed: Use dmae to write to widebus registers in fw_funcs
qed: FW 8.42.2.0 Parser offsets modified
qed: FW 8.42.2.0 Queue Manager changes
qed: FW 8.42.2.0 Expose new registers and change windows
qed: FW 8.42.2.0 Internal ram offsets modifications
MAINTAINERS: Add entry for Marvell OcteonTX2 Physical Function driver
Documentation: net: octeontx2: Add RVU HW and drivers overview
octeontx2-pf: ethtool RSS config support
octeontx2-pf: Add basic ethtool support
...
|
|
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
The 1588 standard defines one step operation for both Sync and
PDelay_Resp messages. Up until now, hardware with P2P one step has
been rare, and kernel support was lacking. This patch adds support of
the mode in anticipation of new hardware developments.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Parity error from the hardware will cause PF to lose the state
of their VFs due to PF's internal reload and hardware reset following
the parity error. Restrict any configuration request from the VFs after
the parity as it could cause unexpected hardware behavior, only way
for VFs to recover would be to trigger FLR on VFs and reload them.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
Commit 04f05230c5c13 ("bnx2x: Remove configured vlans as
part of unload sequence."), introduced a regression in driver
that as a part of VF's reload flow, VLANs created on the VF
doesn't get re-configured in hardware as vlan metadata/info
was not getting cleared for the VFs which causes vlan PING to stop.
This patch clears the vlan metadata/info so that VLANs gets
re-configured back in the hardware in VF's reload flow and
PING/traffic continues for VLANs created over the VFs.
Fixes: 04f05230c5c13 ("bnx2x: Remove configured vlans as part of unload sequence.")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Sudarsana Kalluru <skalluru@marvell.com>
Signed-off-by: Shahed Shaikh <shshaikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
