| Age | Commit message (Collapse) | Author |
|---|
|
WCN7850 uses error dst ring as mon dest ring. Each time hardware
receives a packet, will fill the payload into mon dest ring.
The mon dest ring may store many MSDUs, which belonged to different
MPDUs. Need to retrieve MSDUs based on the PPDU ID, only processing the
MSDUs with same PPDU ID each time.
The PPDU ID is used in cycles, the difference between the PPDU IDs
of the two rings must be checked. If the status PPDU ID minus the
dest PPDU ID is greater than 20000, it is considered a wrap-around
case.
After reaping the mon dest ring, should prepare packet and deliver it to
mac80211 when status PPDU ID is equal to dest PPDU ID. Then start to
process next PPDU if exists.
But if dest PPDU ID > status PPDU ID, should hold on to mon dest ring
processing. If it exceeds 16 consecutive times, status PPDU ID will be
forcibly set to dest PPDU ID to avoid backpressure issue.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-11-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently for CCMP256, GCMP128 and GCMP256 ciphers, in
ath12k_install_key() IEEE80211_KEY_FLAG_GENERATE_IV_MGMT is not set and
in ath12k_mac_mgmt_tx_wmi() a length of IEEE80211_CCMP_MIC_LEN is reserved
for all ciphers.
This results in unexpected drop of protected management frames in case
either of above 3 ciphers is used. The reason is, without
IEEE80211_KEY_FLAG_GENERATE_IV_MGMT set, mac80211 will not generate
CCMP/GCMP headers in TX frame for ath12k.
Also MIC length reserved is wrong and such frames are dropped by hardware.
Fix this by setting IEEE80211_KEY_FLAG_GENERATE_IV_MGMT flag for above
ciphers and by reserving proper MIC length for those ciphers.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250415195812.2633923-2-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
In MLO case, all link peers share the same REO queue, so the queue
should be allocated only once, currently this is done by checking
primary_link flag in ath12k_dp_rx_peer_tid_setup(). However, the
check not only avoids duplicate allocation, but also bypasses sending
queue configuration to firmware for non-primary links. In an upcoming
patch, changes will be added to make this check no-ops for WCN7850,
as WCN7850 firmware needs to be explicitly notified each link peer's
queue configuration. That said, the duplicate allocation would arise
again after that change, hence it needs to be resolved before hand.
Since all link peers share the same queue, it should be allocated per
MLD peer, not per link peer. So change to do allocation once and save
it in MLD peer, link peers can simply get queue configuration from
there.
Also relocate ath12k_reoq_buf structure to core.h to avoid circular
dependency.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250409-ath12k-wcn7850-mlo-support-v2-7-3801132ca2c3@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently vaddr, paddr and size fields are located together with other
fields in ath12k_dp_rx_tid structure. Logically they represents the
REO queue buffer so better to group them in an individual structure.
Introduce a new structure ath12k_reoq_buf to group them. This improves
code readability, and benefits the upcoming patch where this structure
is heavily accessed.
While at it, change vaddr type to 'void *' since it is actually not
pointing to any u32 buffer. Also rename paddr as paddr_aligned to better
reflect its actual meaning.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250409-ath12k-wcn7850-mlo-support-v2-6-3801132ca2c3@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
In ath12k_dp_rx_h_mpdu(), during the undecap to native wifi mode, the rx
descriptor memory is overwritten. After this function call, any subsequent
accesses to rx descriptor related memory yield invalid values. Fix this by
replacing instances where rx_desc was used with the pre-cached information
in rx_info. This ensures that the values populated from the rx descriptor
are accurate and prevents invalid memory access.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: Karthikeyan Periyasamy <karthikeyan.periyasamy@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <karthikeyan.periyasamy@oss.qualcomm.com>
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250402182917.2715596-3-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
In ath12k_dp_rx_h_mpdu(), as part of undecap to native wifi mode, the rx
descriptor memory is getting overwritten. After this function call, all
the rx descriptor related memory accesses give invalid values. To handle
this scenario, introduce a new structure ath12k_dp_rx_info which
pre-caches all the required fields from the rx descriptor before calling
ath12k_dp_rx_h_ppdu(). This rx_info structure will be used in the next
patch.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: Karthikeyan Periyasamy <karthikeyan.periyasamy@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <karthikeyan.periyasamy@oss.qualcomm.com>
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250402182917.2715596-2-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
The current code in dp_rx.h declares the ath12k_dp_rx_h_find_peer() twice.
Fix this by removing one of the redundant declarations of
ath12k_dp_rx_h_find_peer() to ensure that the function is declared only
once.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Link: https://patch.msgid.link/20250219053640.223734-1-praneesh.p@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, the transmit rate of "iw dev xxx station dump" command
always show an invalid value.
To address this issue, ath12k parse the info of transmit complete
report from firmware and indicate the transmit rate to mac80211.
This patch affects the station mode of WCN7850 and QCN9274.
After that, "iw dev xxx station dump" show the correct transmit rate.
Such as:
Station 00:03:7f:12:03:03 (on wlo1)
inactive time: 872 ms
rx bytes: 219111
rx packets: 1133
tx bytes: 53767
tx packets: 462
tx retries: 51
tx failed: 0
beacon loss: 0
beacon rx: 403
rx drop misc: 74
signal: -95 dBm
beacon signal avg: -18 dBm
tx bitrate: 1441.1 MBit/s 80MHz EHT-MCS 13 EHT-NSS 2 EHT-GI 0
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219715
Link: https://patch.msgid.link/20250115063537.35797-2-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Apply tid queue setup based on all link stations on receiving ampdu action
params for an ML Station.
Modify ath12k_get_ar_by_vif() to fetch ar based on link arvif inside ahvif.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241126171139.2350704-5-kvalo@kernel.org
|
|
To prepare the driver for MLO support, split the driver vif data structure to
scale for multiple links. This requires changing the use of arvif to per link
and not per hw which can now comprise of multiple links. Also since most
configurations from mac80211 are done per link, do refactoring of the driver
functions to apply these configurations at link level.
Split ath12k_vif which is the driver private of ieee80211_vif to store link
specific information as ath12k_link_vif. For default use cases the ath12k vif
will have a preallocated link vif called deflink which will be used by non ML
and the first link vif of ML vif.
With MLO support to be added, remaining link vifs will be allocated during
channel assignment where vdev create/start happens. These link vifs will be
freed during interface down.
Current ath12k_vif(arvif) structure
+---------------+ +---------------+ +---------------+
| ieee80211_vif | | ieee80211_vif | | ieee80211_vif |
| private data | | private data | | private data |
| | | | | |
| ath12k_vif | | ath12k_vif | | ath12k_vif |
| (arvif) | | (arvif) | | (arvif) |
| | | | | |
| +----------+ | | +----------+ | | +----------+ |
| |*ar (2GHz)| | | |*ar (5GHz)| | | |*ar (2GHz)| |
| +----------+ | | +----------+ | | +----------+ |
| | | | | |
+---------------+ +---------------+ +---------------+
The new ath12k_vif (ahvif) containing ath12k_link_vif(s) (arvif) (deflink is
preallocated member which is always the first link if ieee80211_vif is MLD and
is the only link otherwise):
+---------------------------------+
| ieee80211_vif |
| private data |
| |
| ath12k_vif(ahvif) |
| |
| +-------------------------------+
| |ath12k_link_vif deflink (arvif)|
| | +---------------+ |
| | | *ar(2GHz) | |
| +-------------------------------+
| +-------------------------------+
| | ath12k_link_vif *link (arvif)|
| | +---------------+ |
| | | *ar(5GHz) | |
| +-------------------------------+
| +-------------------------------+
| | ath12k_link_vif *link (arvif)|
| | +---------------+ |
| | | *ar(6GHz) | |
| +-------------------------------+
| |
+---------------------------------+
To refactor existing ath12k_vif to make use of link vifs, following
changes are made:
1. ath12k_vif now called by variable name ahvif storing multiple
arvifs (struct ah12k_link_vif) and also has a back pointer to ieee80211_vif.
2. In this patch set, only deflink is used to be on par with the
existing code. When MLO support is added the link id will be used to fetch
the arvif.
3. For mac80211 ops which doesn't use specific link_id, the config or info
is common for the vif, hence apply the config to all link vifs.
The links_map in the ahvif, will be used to identify all the link vifs that
are setup.
4. Change ath12k_vif_to_arvif() as ath12k_vif_to_ahvif() to fetch the
hw level vif. The link vif can be fetched from ahvif->link[], or the
deflink can be accessed via ahvif->deflink. API to access link
vif (arvif) by passing link_id can be introduced with MLO Support.
5. The ieee80211_vif can be accessed from ahvif using ath12k_ahvif_to_vif().
The locking continues to use wiphy_lock() for protecting access to most data in
struct ath12k&co, there are no changes in that regard. Though struct
ath12k_vif::link[] is protected with RCU.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241015171416.518022-2-kvalo@kernel.org
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
|
|
Add extended htt stats parser and print the corresponding TLVs associated
with the requested htt_stats_type.
Add support for TX PDEV related htt stats.
Sample output:
--------------
echo 1 > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats_type
cat /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats
HTT_TX_PDEV_STATS_CMN_TLV:
mac_id = 0
comp_delivered = 0
self_triggers = 256
hw_queued = 275
hw_reaped = 275
underrun = 241
hw_paused = 0
hw_flush = 0
hw_filt = 1
tx_abort = 0
ppdu_ok = 246
mpdu_requeued = 0
tx_xretry = 0
data_rc = 3
mpdu_dropped_xretry = 0
illegal_rate_phy_err = 0
cont_xretry = 0
tx_timeout = 0
tx_time_dur_data = 0
pdev_resets = 0
phy_underrun = 0
txop_ovf = 0
seq_posted = 247
seq_failed_queueing = 0
seq_completed = 247
seq_restarted = 0
seq_txop_repost_stop = 0
next_seq_cancel = 0
dl_mu_mimo_seq_posted = 0
dl_mu_ofdma_seq_posted = 0
ul_mu_mimo_seq_posted = 0
ul_mu_ofdma_seq_posted = 0
mu_mimo_peer_blacklisted = 0
seq_qdepth_repost_stop = 0
seq_min_msdu_repost_stop = 0
mu_seq_min_msdu_repost_stop = 0
seq_switch_hw_paused = 0
next_seq_posted_dsr = 0
seq_posted_isr = 0
seq_ctrl_cached = 0
mpdu_count_tqm = 0
msdu_count_tqm = 0
mpdu_removed_tqm = 0
msdu_removed_tqm = 0
remove_mpdus_max_retries = 0
mpdus_sw_flush = 0
mpdus_hw_filter = 0
mpdus_truncated = 0
mpdus_ack_failed = 0
mpdus_expired = 0
mpdus_seq_hw_retry = 0
ack_tlv_proc = 0
coex_abort_mpdu_cnt_valid = 0
coex_abort_mpdu_cnt = 5
num_total_ppdus_tried_ota = 5
num_data_ppdus_tried_ota = 0
local_ctrl_mgmt_enqued = 247
local_ctrl_mgmt_freed = 247
local_data_enqued = 0
local_data_freed = 0
mpdu_tried = 0
isr_wait_seq_posted = 0
tx_active_dur_us_low = 0
tx_active_dur_us_high = 0
fes_offsets_err_cnt = 0
HTT_TX_PDEV_STATS_URRN_TLV:
urrn_stats = 0:0, 1:241, 2:0
HTT_TX_PDEV_STATS_SIFS_TLV:
sifs_status = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0
HTT_TX_PDEV_STATS_FLUSH_TLV:
flush_errs = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0,
11:0, 12:0, 13:0, 14:0, 15:0, 16:0, 17:0, 18:0, 19:0, 20:0, 21:0, 22:0,
23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0, 31:0, 32:0, 33:0, 34:0,
35:0, 36:0, 37:0, 38:0, 39:0, 40:0, 41:0, 42:0, 43:0, 44:0, 45:0, 46:0,
47:0, 48:0, 49:0, 50:0, 51:0, 52:0, 53:0, 54:0, 55:0, 56:0, 57:0, 58:0,
59:0, 60:0, 61:0, 62:0, 63:0, 64:0, 65:0, 66:0, 67:0, 68:0, 69:0, 70:0,
71:0, 72:0, 73:0, 74:0, 75:0, 76:0, 77:0, 78:0, 79:0, 80:0, 81:0, 82:0,
83:0, 84:0, 85:0, 86:0, 87:0, 88:0, 89:0, 90:0, 91:0, 92:0, 93:0, 94:0,
95:0, 96:0, 97:0, 98:0, 99:0, 100:0, 101:0, 102:0, 103:0, 104:0, 105:0,
106:0, 107:0, 108:0, 109:0, 110:0, 111:0, 112:0, 113:0, 114:0, 115:0,
116:0, 117:0, 118:0, 119:0, 120:0, 121:0, 122:0, 123:0, 124:0, 125:0,
126:0, 127:0
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Dinesh Karthikeyan <quic_dinek@quicinc.com>
Co-developed-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240626085854.2500681-4-quic_rgnanase@quicinc.com
|
|
Currently pktlog is stopped in suspend callback and started in
resume callback, and in either scenarios it's basically to
delete/modify ab->mon_reap_timer and to purge related rings.
For WCN7850 it's pointless because pktlog is not enabled: both
ab->mon_reap_timer and those rings are not initialized.
So remove pktlog handling in suspend/resume callbacks. And
further, remove these two functions and related callee because
no one is calling them.
Other chips are not affected because now only WCN7850 supports
suspend/resume.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412060620.27519-8-quic_bqiang@quicinc.com
|
|
When a packet arrives in Rx rings, the RX descriptor moves from the used
list to the free list. Then, the rxdma ring gets replenished, where the Rx
descriptor again moves from the free list to the used list. At the end, the
descriptor came to the used list with unnecessary list movement. The
descriptor used list is maintained in the Rxdma ring structure, which
creates lock contention for the list operations (add, delete) in the Rx
data path. Optimize the Rx data path by removing the used list from the
common Rxdma ring and maintain as a local variable in the Rx ring handler
itself, which avoid lock contention. Now, to find the used list descriptor
during descriptor cleanup, we need to check the in_use flag for each Rx
descriptor.
This is a simple UDP UL throughput test case results on x86+NUC device
with QCN9274 card, which clearly shows 8% to 12% improvement in the CPU
idle for the same ingress traffic.
Before:
Average: CPU %usr %nice %sys %iowait %irq %soft %steal %guest %gnice %idle
Average: all 0.24 0.00 12.54 0.08 0.00 23.33 0.00 0.00 0.00 63.81
After:
Average: CPU %usr %nice %sys %iowait %irq %soft %steal %guest %gnice %idle
Average: all 0.34 0.00 4.60 0.00 0.00 19.59 0.00 0.00 0.00 75.47
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240320010615.91331-3-quic_periyasa@quicinc.com
|
|
Currently Rxdma replenish require HW conversion argument which is
unnecessary argument since ath12k driver configures the Rxdma only
in HW conversion. To optimize the rx data path per packet, avoid
the explicit unnecessary argument and condition check in the rx
replenish.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00125-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231111043934.20485-4-quic_periyasa@quicinc.com
|
|
Currently all Rxdma replenish callers pass the same return
buffer manager id argument, so make it implicitly. To
optimize the rx data path per packet, avoid the explicit
unnecessary argument in Rxdma replenish function.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00125-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231111043934.20485-3-quic_periyasa@quicinc.com
|
|
Currently all Rxdma replenish callers pass zero for the mac id
argument, so make it as zero implicitly. To optimize the rx
data path per packet, avoid the explicit unnecessary argument
in Rxdma replenish function.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00125-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231111043934.20485-2-quic_periyasa@quicinc.com
|
|
ath12k is a new mac80211 driver for Qualcomm Wi-Fi 7 devices, first
supporting QCN9274 and WCN7850 PCI devices. QCN9274 supports both AP
and station; WCN7850 supports only station mode. Monitor mode is not
(yet) supported. Only PCI bus devices are supported.
ath12k is forked from an earlier version of ath11k. It was simpler to
have a "clean start" for the new generation and not try to share the
code with ath11k. This makes maintenance easier and avoids major
changes in ath11k, which would have significantly increased the risk
of regressions in existing setups.
ath12k uses le32 and cpu_to_le32() macros to handle endian
conversions, instead of using the firmware byte swap feature utilized
by ath11k. There is only one kernel module, named ath12k.ko.
Currently ath12k only supports HE mode (IEEE 802.11ax) or older, but
work is ongoing to add EHT mode (IEEE 802.11be) support.
The size of the driver is ~41 kLOC and 45 files. To make the review
easier, this initial version of ath12k does not support Device Tree,
debugfs or any other extra features. Those will be added later, after
ath12k is accepted to upstream.
The driver is build tested by Intel's kernel test robot with both GCC
and Clang. Sparse reports no warnings. The driver is mostly free of
checkpatch warnings, albeit few of the warnings are omitted on
purpose, list of them here:
https://github.com/qca/qca-swiss-army-knife/blob/master/tools/scripts/ath12k/ath12k-check#L52
The driver has had multiple authors who are listed in alphabetical
order below.
Co-developed-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com>
Signed-off-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com>
Co-developed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Co-developed-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Signed-off-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Co-developed-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Co-developed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Co-developed-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Co-developed-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Co-developed-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Co-developed-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Signed-off-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Co-developed-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
|
