| Age | Commit message (Collapse) | Author |
|---|
|
Currently, RX is_mcbc bit is set for packets sent from client as
destination address (DA) is multicast/broadcast address, but packets
are actually unicast as receiver address (RA) is not multicast address.
Hence, packets are not handled properly due to this is_mcbc bit.
Therefore, reset the is_mcbc bit if interface type is AP.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250411061523.859387-3-quic_sarishar@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
mac80211 expects link_id in some scenarios or else the packet might
get dropped. Hence, add link_id information before delivering the skb.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241209185421.376381-10-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently reoqueue tid setup uses lookup table (LUT) during peer association,
but for ML peer there will be multiple link peers (belonging to different
underlying firmware) affiliated to each other. Hence the reo queue should be
setup only on one of the links which is the primary link.
Add changes to create separate ML reo queue lookup table for ML peers and use
the same while setting up rx tid for ML peer's primary link. For ML peers use
ml_peer_id instead of peer_id to setup/lookup the reo queue entry in the LUT.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241121155806.1862733-6-kvalo@kernel.org
|
|
In case of Multi-link operation, data path peer setup and tid setup should be
done only for primary link of multi-link station. Add changes to introduce
primary link is peer. Currently, association link will be considered as primary
link.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241121155806.1862733-4-kvalo@kernel.org
|
|
Add changes to handle multi-link station state change with proper
link handling and add code changes for ML peer creation, peer deletion.
In ath12k_mac_assign_link_sta() initialise all arsta fields first and only then
call rcu_assign_pointer(). This is to make sure that readers don't have access
to arsta which is still modified.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241121155806.1862733-2-kvalo@kernel.org
|
|
Multi-link stations are identified in driver using the multi-link
peer id and they have ATH12K_PEER_ML_ID_VALID bit set in the id. Add a helper
to find multi-link station using the multi-link peer id.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241101151705.165987-8-kvalo@kernel.org
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
|
|
Add helper functions for multi link peer addition and deletion. And add address
validation to ensure we are not creating link peers (belonging to different
clients) with same MLD address. To aid in this validation for faster lookup,
add a new list of ML peers to struct ath12k_hw::ml_peers and use the same for
parsing for the above address validation use cases.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241101151705.165987-6-kvalo@kernel.org
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
|
|
To prepare the driver for MLO support, split the driver vif data structure to
scale for multiple links. This requires changing the use of arvif to per link
and not per hw which can now comprise of multiple links. Also since most
configurations from mac80211 are done per link, do refactoring of the driver
functions to apply these configurations at link level.
Split ath12k_vif which is the driver private of ieee80211_vif to store link
specific information as ath12k_link_vif. For default use cases the ath12k vif
will have a preallocated link vif called deflink which will be used by non ML
and the first link vif of ML vif.
With MLO support to be added, remaining link vifs will be allocated during
channel assignment where vdev create/start happens. These link vifs will be
freed during interface down.
Current ath12k_vif(arvif) structure
+---------------+ +---------------+ +---------------+
| ieee80211_vif | | ieee80211_vif | | ieee80211_vif |
| private data | | private data | | private data |
| | | | | |
| ath12k_vif | | ath12k_vif | | ath12k_vif |
| (arvif) | | (arvif) | | (arvif) |
| | | | | |
| +----------+ | | +----------+ | | +----------+ |
| |*ar (2GHz)| | | |*ar (5GHz)| | | |*ar (2GHz)| |
| +----------+ | | +----------+ | | +----------+ |
| | | | | |
+---------------+ +---------------+ +---------------+
The new ath12k_vif (ahvif) containing ath12k_link_vif(s) (arvif) (deflink is
preallocated member which is always the first link if ieee80211_vif is MLD and
is the only link otherwise):
+---------------------------------+
| ieee80211_vif |
| private data |
| |
| ath12k_vif(ahvif) |
| |
| +-------------------------------+
| |ath12k_link_vif deflink (arvif)|
| | +---------------+ |
| | | *ar(2GHz) | |
| +-------------------------------+
| +-------------------------------+
| | ath12k_link_vif *link (arvif)|
| | +---------------+ |
| | | *ar(5GHz) | |
| +-------------------------------+
| +-------------------------------+
| | ath12k_link_vif *link (arvif)|
| | +---------------+ |
| | | *ar(6GHz) | |
| +-------------------------------+
| |
+---------------------------------+
To refactor existing ath12k_vif to make use of link vifs, following
changes are made:
1. ath12k_vif now called by variable name ahvif storing multiple
arvifs (struct ah12k_link_vif) and also has a back pointer to ieee80211_vif.
2. In this patch set, only deflink is used to be on par with the
existing code. When MLO support is added the link id will be used to fetch
the arvif.
3. For mac80211 ops which doesn't use specific link_id, the config or info
is common for the vif, hence apply the config to all link vifs.
The links_map in the ahvif, will be used to identify all the link vifs that
are setup.
4. Change ath12k_vif_to_arvif() as ath12k_vif_to_ahvif() to fetch the
hw level vif. The link vif can be fetched from ahvif->link[], or the
deflink can be accessed via ahvif->deflink. API to access link
vif (arvif) by passing link_id can be introduced with MLO Support.
5. The ieee80211_vif can be accessed from ahvif using ath12k_ahvif_to_vif().
The locking continues to use wiphy_lock() for protecting access to most data in
struct ath12k&co, there are no changes in that regard. Though struct
ath12k_vif::link[] is protected with RCU.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241015171416.518022-2-kvalo@kernel.org
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
|
|
Update the copyright for all ath12k files modified on behalf of
Qualcomm Innovation Center, Inc. in 2023.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231128-ath12kcopyrights-v1-1-be0b7408cbac@quicinc.com
|
|
When max virtual ap interfaces are configured in all the bands with
ACS and hostapd restart is done every 60s, a crash is observed at
random times.
In the above scenario, a fragmented packet is received for self peer,
for which rx_tid and rx_frags are not initialized in datapath.
While handling this fragment, crash is observed as the rx_frag list
is uninitialized and when we walk in ath12k_dp_rx_h_sort_frags,
skb null leads to exception.
To address this, before processing received fragments we check
dp_setup_done flag is set to ensure that peer has completed its
dp peer setup for fragment queue, else ignore processing the
fragments.
Call trace:
PC points to "ath12k_dp_process_rx_err+0x4e8/0xfcc [ath12k]"
LR points to "ath12k_dp_process_rx_err+0x480/0xfcc [ath12k]".
The Backtrace obtained is as follows:
ath12k_dp_process_rx_err+0x4e8/0xfcc [ath12k]
ath12k_dp_service_srng+0x78/0x260 [ath12k]
ath12k_pci_write32+0x990/0xb0c [ath12k]
__napi_poll+0x30/0xa4
net_rx_action+0x118/0x270
__do_softirq+0x10c/0x244
irq_exit+0x64/0xb4
__handle_domain_irq+0x88/0xac
gic_handle_irq+0x74/0xbc
el1_irq+0xf0/0x1c0
arch_cpu_idle+0x10/0x18
do_idle+0x104/0x248
cpu_startup_entry+0x20/0x64
rest_init+0xd0/0xdc
arch_call_rest_init+0xc/0x14
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230821130343.29495-2-quic_hprem@quicinc.com
|
|
ath12k is a new mac80211 driver for Qualcomm Wi-Fi 7 devices, first
supporting QCN9274 and WCN7850 PCI devices. QCN9274 supports both AP
and station; WCN7850 supports only station mode. Monitor mode is not
(yet) supported. Only PCI bus devices are supported.
ath12k is forked from an earlier version of ath11k. It was simpler to
have a "clean start" for the new generation and not try to share the
code with ath11k. This makes maintenance easier and avoids major
changes in ath11k, which would have significantly increased the risk
of regressions in existing setups.
ath12k uses le32 and cpu_to_le32() macros to handle endian
conversions, instead of using the firmware byte swap feature utilized
by ath11k. There is only one kernel module, named ath12k.ko.
Currently ath12k only supports HE mode (IEEE 802.11ax) or older, but
work is ongoing to add EHT mode (IEEE 802.11be) support.
The size of the driver is ~41 kLOC and 45 files. To make the review
easier, this initial version of ath12k does not support Device Tree,
debugfs or any other extra features. Those will be added later, after
ath12k is accepted to upstream.
The driver is build tested by Intel's kernel test robot with both GCC
and Clang. Sparse reports no warnings. The driver is mostly free of
checkpatch warnings, albeit few of the warnings are omitted on
purpose, list of them here:
https://github.com/qca/qca-swiss-army-knife/blob/master/tools/scripts/ath12k/ath12k-check#L52
The driver has had multiple authors who are listed in alphabetical
order below.
Co-developed-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com>
Signed-off-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com>
Co-developed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Co-developed-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Signed-off-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Co-developed-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Co-developed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Co-developed-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Co-developed-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Co-developed-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Co-developed-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Signed-off-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Co-developed-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
|
