Age | Commit message (Collapse) | Author |
|
The rk3036 does contain a usb2phy, just until now it was just used
implicitly without additional configuration. As we now have the bits
in place for it getting actually controlled, add the necessary phy-node
to the GRF simple-mfd.
Enable the phy-ports in the same patch to not create bisectability
issues, as hooking up the phys to the usb controllers would create
probe deferrals until a board enables them. Doing everything in one
patch, solves that issue.
Only rk3036-kylin actually enabled the usb controllers, so is the only
board affected.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250503201512.991277-4-heiko@sntech.de
|
|
Modify the corresponding vccio according to the schematic of
Sonoff iHost. This change aligns the device tree with the actual
hardware design and improves peripheral stability.
Signed-off-by: Hao Zhang <hao.zhang@coolkit.cn>
Link: https://lore.kernel.org/r/20250509101419.460473-3-hao.zhang@coolkit.cn
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Reduce max-frequency from 50MHz to 25MHz to improve WiFi module stability
on some Sonoff iHost units. Remove unsupported or redundant properties,
and keep only minimal, validated configuration.
Signed-off-by: Hao Zhang <hao.zhang@coolkit.cn>
Link: https://lore.kernel.org/r/20250509101419.460473-2-hao.zhang@coolkit.cn
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The rk3066 contains a Mali400 GPU, so enable it.
There is no individual (or even controllable) supply for the GPU
on the board.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250503201043.990933-3-heiko@sntech.de
|
|
The marsboard does have a regular hdmi-a connector and can simply
use the already existing infrastructure (rk3066-hdmi) for display
output.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250503201043.990933-2-heiko@sntech.de
|
|
This reverts commit 1580ccb6ed9dc76b8ff3e2d8912e8215c8b0fa6d.
The HSYNC/VSYNC polarity of rk3036 HDMI are controlled by GRF.
Without the polarity configuration in GRF, it can be observed from
the HDMI protocol analyzer that the H/V front/back timing output
by RK3036 HDMI are currently not in line with the specifications.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de> #rk3036-kylin
Link: https://lore.kernel.org/r/20250422070455.432666-7-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The RK3036 HDMI DDC bus requires it's PHY's reference clock to be
enabled first before normal DDC communication can be carried out.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de> #rk3036-kylin
Link: https://lore.kernel.org/r/20250422070455.432666-6-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The "clock-latency" property is part of the deprecated opp-v1 binding
and is redundant if the opp-v2 table has equal or larger values in any
"clock-latency-ns". Add any missing "clock-latency-ns" properties and
remove "clock-latency".
Signed-off-by: "Rob Herring (Arm)" <robh@kernel.org>
Link: https://lore.kernel.org/r/20250410-dt-cpu-schema-v2-10-63d7dc9ddd0a@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add aliases for the MMC devices so that after the system starts up,
they will all have fixed device numbers.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Link: https://lore.kernel.org/r/20250324125215.160616-1-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Pull SoC devicetree updates from Arnd Bergmann:
"This release adds the devicetree files for an impressive number of new
SoC variants, though as expected these are all related to others we
already support:
- The microchip sam9x7 devicetree is now added, after the device
driver and platform code has already made it in. This is likely the
last ARMv5 (!) platform to ever get added, updating the 20+ year
old at91/sam9 platform with DDR3 memory and gigabit ethernet.
- On the Apple platform, there are now devicetree files for a number
of A-series SoCs in addition to the M-series ones, these are used
primarily in phones and tablets, but are closely related to the
already supported chips.
- Samsung Exynos 8895 and Exynos 990 are more phone SoCs used in
older Samsung Galaxy phones.
- Qualcomm Snapdragon 778G (SM7325) is another phone SoC, closely
related to the Snapdragon 7c+ Gen 3 (SC7280) used in low-end
laptops.
- Rockchip RK3528 and RK3576 are new variants of their TV box and
Tablet chips, still using the older ARMv8.0 cores from
RK3328/RK3399 but with a newer process and other improvements from
the RK35xx (otherwise ARMv8.2) chips. RK3566T and RK3399-S are also
added, these are just lower-cost versions of their normal
counterparts.
- TI J742S2 is a feature-reduced version of the J784s4
industrial/automotive SoC, with fewer CPU cores.
- Sophgo SG2002 is an embedded SoC with one RISC-V (C906) and one ARM
(Cortex-A53) core, at this point support is only added for running
on the RISC-V side on the LicheeRV Nano board.
A total of 92 new .dts files describing individual machines is added,
which must be a new record. The majority of these is for the newly
added chips above, notably all the Apple phones and tablets. The other
new machines include nine industrial/embedded boards with NXP i.MX6 or
i.MX8 SoCs, eight for Rockchips RK35XX and one or two each for
Rockchips RV1109, RK3308, Allwinner A33, Tegra 234, Qualcomm
qcs9100/sc8280xp/x1e80100, TI AM625 and Starfive JH7110.
As usual there are also many newly added features in existing boards
as well as cleanups and minor bugfixes"
* tag 'soc-dt-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (718 commits)
arm64: dts: apm: Remove unused and undocumented "bus_num" property
arm: dts: spear13xx: Remove unused and undocumented "pl022,slave-tx-disable" property
arm64: dts: amd: Remove unused and undocumented "amd,zlib-support" property
arm64: dts: lg131x: Update spi clock properties
arm64: dts: seattle: Update spi clock properties
arm64: dts: rockchip: use less broad pinctrl for pcie3x1 on Radxa E25
arm64: dts: rockchip: add Radxa ROCK 5C
dt-bindings: arm: rockchip: add Radxa ROCK 5C
arm64: dts: rockchip: orangepi-5-plus: Enable GPU
arm64: dts: rockchip: enable USB3 on NanoPC-T6
arm64: dts: rockchip: adapt regulator nodenames to preferred form
arm64: dts: rockchip: Enable HDMI display for rk3588 Cool Pi GenBook
arm64: dts: rockchip: Enable HDMI display for rk3588 Cool Pi 4B
arm64: dts: rockchip: Enable HDMI0 for rk3588 Cool Pi CM5 EVB
arm64: dts: rockchip: Enable HDMI on NanoPi R6C/R6S
arm64: dts: rockchip: Enable GPU on NanoPi R6C/R6S
arm64: dts: rockchip: Enable HDMI on Hardkernel ODROID-M2
arm64: dts: rockchip: Remove non-removable flag from sdmmc on rk3576-sige5
arm64: dts: allwinner: a100: perf1: Add eMMC and MMC node
arm64: dts: allwinner: pinephone: Add mount matrix to accelerometer
...
|
|
The preferred nodename for fixed-regulators has changed to
pattern: '^regulator(-[0-9]+v[0-9]+|-[0-9a-z-]+)?$'
Fix all Rockchip DT regulator nodenames.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/cfc3cfe1-086b-48f1-9b89-f17c9391d3cc@gmail.com
[Also include the backlight-regulator and panel-regulator from
rk3288-veyron-edp, and adapt the Pinky device accordingly]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Both the node name as well as the compatible were not named
according to the binding expectations, fix that.
Fixes: 47bf3a5c9e2a ("ARM: dts: rockchip: add the sound setup for rk3036-kylin board")
Cc: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20241008203940.2573684-15-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Compatible and clock names did not match the existing binding.
So set the correct values and re-order+rename the clocks.
It looks like no rk3036 board did use the spi controller so far,
so this was never detected on a running device yet.
Fixes: f629fcfab2cd ("ARM: dts: rockchip: support the spi for rk3036")
Cc: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20241008203940.2573684-14-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Neither the binding nor the driver implementation specify/use the grf
reference provided in the rk3036. And neither does the newer rk3128
user of the hdmi controller. So drop the rockchip,grf property.
Fixes: b7217cf19c63 ("ARM: dts: rockchip: add hdmi device node for rk3036")
Cc: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20241008203940.2573684-13-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The acodec node is not conformant to the binding.
Set the correct nodename, use the correct compatible, add the needed
#sound-dai-cells and sort the rockchip,grf below clocks properties
as expected.
Fixes: faea098e1808 ("ARM: dts: rockchip: add core rk3036 dtsi")
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20241008203940.2573684-12-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Saib is an consumer electronics board from Relfor labs
Features:
- Rockchip RV1109
- 1GB DDR4
- 4GB eMMC
- Realtek RTL8821CS Wi-Fi/BT
- IR transmitter/receiver
- RV3028 RTC
- Switch
- User leds
Add support for it.
Signed-off-by: Karthikeyan Krishnasamy <karthikeyan@linumiz.com>
Link: https://lore.kernel.org/r/20240912142451.2952633-7-karthikeyan@linumiz.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add watchdog node for Rockchip RV1126
Signed-off-by: Karthikeyan Krishnasamy <karthikeyan@linumiz.com>
Link: https://lore.kernel.org/r/20240912142451.2952633-3-karthikeyan@linumiz.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add previously omitted pwm node and possible pinctrl for Rockchip RV1126
Signed-off-by: Karthikeyan Krishnasamy <karthikeyan@linumiz.com>
Link: https://lore.kernel.org/r/20240903105245.715899-4-karthikeyan@linumiz.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add i2s0 node and possible pinctrl for Rockchip RV1126
Signed-off-by: Karthikeyan Krishnasamy <karthikeyan@linumiz.com>
Link: https://lore.kernel.org/r/20240903105245.715899-3-karthikeyan@linumiz.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add i2c3 node and possible pinctrl for Rockchip RV1126
Signed-off-by: Karthikeyan Krishnasamy <karthikeyan@linumiz.com>
Link: https://lore.kernel.org/r/20240903105245.715899-2-karthikeyan@linumiz.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
There is no DAC connected to the SPI bus of the Elgin RV1108 R1 board.
There is a JG10309-01 LCD controlled via SPI though.
Properly describe it by adding the "elgin,jg10309-01" compatible
string.
Reported-by: Conor Dooley <conor.dooley@microchip.com>
Closes: https://lore.kernel.org/linux-arm-kernel/20240717-parrot-malt-83cc04bf6b36@spud/
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240829113158.3324928-3-festevam@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add nodes for the vpu and it's attached iommu which are both part of the
RK3128_PD_VIDEO powerdomain.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20240523185633.71355-4-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Due to inter-branch dependencies, it was necessary to add the rk3128
sfc controller with its hclk_sfc using the numeric clock id value
instead of the nicer constant from the binding.
Now that it's available, change over to this constant.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20240623215631.440399-1-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Not much excitement - a handful of large patchsets (devmem among them)
did not make it in time.
Core & protocols:
- Use local_lock in addition to local_bh_disable() to protect per-CPU
resources in networking, a step closer for local_bh_disable() not
to act as a big lock on PREEMPT_RT
- Use flex array for netdevice priv area, ensure its cache alignment
- Add a sysctl knob to allow user to specify a default rto_min at
socket init time. Bit of a big hammer but multiple companies were
independently carrying such patch downstream so clearly it's useful
- Support scheduling transmission of packets based on CLOCK_TAI
- Un-pin TCP TIMEWAIT timer to avoid it firing on CPUs later cordoned
off using cpusets
- Support multiple L2TPv3 UDP tunnels using the same 5-tuple address
- Allow configuration of multipath hash seed, to both allow
synchronizing hashing of two routers, and preventing partial
accidental sync
- Improve TCP compliance with RFC 9293 for simultaneous connect()
- Support sending NAT keepalives in IPsec ESP in UDP states.
Userspace IKE daemon had to do this before, but the kernel can
better keep track of it
- Support sending supervision HSR frames with MAC addresses stored in
ProxyNodeTable when RedBox (i.e. HSR-SAN) is enabled
- Introduce IPPROTO_SMC for selecting SMC when socket is created
- Allow UDP GSO transmit from devices with no checksum offload
- openvswitch: add packet sampling via psample, separating the
sampled traffic from "upcall" packets sent to user space for
forwarding
- nf_tables: shrink memory consumption for transaction objects
Things we sprinkled into general kernel code:
- Power Sequencing subsystem (used by Qualcomm Bluetooth driver for
QCA6390) [ Already merged separately - Linus ]
- Add IRQ information in sysfs for auxiliary bus
- Introduce guard definition for local_lock
- Add aligned flavor of __cacheline_group_{begin, end}() markings for
grouping fields in structures
BPF:
- Notify user space (via epoll) when a struct_ops object is getting
detached/unregistered
- Add new kfuncs for a generic, open-coded bits iterator
- Enable BPF programs to declare arrays of kptr, bpf_rb_root, and
bpf_list_head
- Support resilient split BTF which cuts down on duplication and
makes BTF as compact as possible WRT BTF from modules
- Add support for dumping kfunc prototypes from BTF which enables
both detecting as well as dumping compilable prototypes for kfuncs
- riscv64 BPF JIT improvements in particular to add 12-argument
support for BPF trampolines and to utilize bpf_prog_pack for the
latter
- Add the capability to offload the netfilter flowtable in XDP layer
through kfuncs
Driver API:
- Allow users to configure IRQ tresholds between which automatic IRQ
moderation can choose
- Expand Power Sourcing (PoE) status with power, class and failure
reason. Support setting power limits
- Track additional RSS contexts in the core, make sure configuration
changes don't break them
- Support IPsec crypto offload for IPv6 ESP and IPv4 UDP-encapsulated
ESP data paths
- Support updating firmware on SFP modules
Tests and tooling:
- mptcp: use net/lib.sh to manage netns
- TCP-AO and TCP-MD5: replace debug prints used by tests with
tracepoints
- openvswitch: make test self-contained (don't depend on OvS CLI
tools)
Drivers:
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- increase the max total outstanding PTP TX packets to 4
- add timestamping statistics support
- implement netdev_queue_mgmt_ops
- support new RSS context API
- Intel (100G, ice, idpf):
- implement FEC statistics and dumping signal quality indicators
- support E825C products (with 56Gbps PHYs)
- nVidia/Mellanox:
- support HW-GRO
- mlx4/mlx5: support per-queue statistics via netlink
- obey the max number of EQs setting in sub-functions
- AMD/Solarflare:
- support new RSS context API
- AMD/Pensando:
- ionic: rework fix for doorbell miss to lower overhead and
skip it on new HW
- Wangxun:
- txgbe: support Flow Director perfect filters
- Ethernet NICs consumer, embedded and virtual:
- Add driver for Tehuti Networks TN40xx chips
- Add driver for Meta's internal NIC chips
- Add driver for Ethernet MAC on Airoha EN7581 SoCs
- Add driver for Renesas Ethernet-TSN devices
- Google cloud vNIC:
- flow steering support
- Microsoft vNIC:
- support page sizes other than 4KB on ARM64
- vmware vNIC:
- support latency measurement (update to version 9)
- VirtIO net:
- support for Byte Queue Limits
- support configuring thresholds for automatic IRQ moderation
- support for AF_XDP Rx zero-copy
- Synopsys (stmmac):
- support for STM32MP13 SoC
- let platforms select the right PCS implementation
- TI:
- icssg-prueth: add multicast filtering support
- icssg-prueth: enable PTP timestamping and PPS
- Renesas:
- ravb: improve Rx performance 30-400% by using page pool,
theaded NAPI and timer-based IRQ coalescing
- ravb: add MII support for R-Car V4M
- Cadence (macb):
- macb: add ARP support to Wake-On-LAN
- Cortina:
- use phylib for RX and TX pause configuration
- Ethernet switches:
- nVidia/Mellanox:
- support configuration of multipath hash seed
- report more accurate max MTU
- use page_pool to improve Rx performance
- MediaTek:
- mt7530: add support for bridge port isolation
- Qualcomm:
- qca8k: add support for bridge port isolation
- Microchip:
- lan9371/2: add 100BaseTX PHY support
- NXP:
- vsc73xx: implement VLAN operations
- Ethernet PHYs:
- aquantia: enable support for aqr115c
- aquantia: add support for PHY LEDs
- realtek: add support for rtl8224 2.5Gbps PHY
- xpcs: add memory-mapped device support
- add BroadR-Reach link mode and support in Broadcom's PHY driver
- CAN:
- add document for ISO 15765-2 protocol support
- mcp251xfd: workaround for erratum DS80000789E, use timestamps to
catch when device returns incorrect FIFO status
- WiFi:
- mac80211/cfg80211:
- parse Transmit Power Envelope (TPE) data in mac80211 instead
of in drivers
- improvements for 6 GHz regulatory flexibility
- multi-link improvements
- support multiple radios per wiphy
- remove DEAUTH_NEED_MGD_TX_PREP flag
- Intel (iwlwifi):
- bump FW API to 91 for BZ/SC devices
- report 64-bit radiotap timestamp
- enable P2P low latency by default
- handle Transmit Power Envelope (TPE) advertised by AP
- remove support for older FW for new devices
- fast resume (keeping the device configured)
- mvm: re-enable Multi-Link Operation (MLO)
- aggregation (A-MSDU) optimizations
- MediaTek (mt76):
- mt7925 Multi-Link Operation (MLO) support
- Qualcomm (ath10k):
- LED support for various chipsets
- Qualcomm (ath12k):
- remove unsupported Tx monitor handling
- support channel 2 in 6 GHz band
- support Spatial Multiplexing Power Save (SMPS) in 6 GHz band
- supprt multiple BSSID (MBSSID) and Enhanced Multi-BSSID
Advertisements (EMA)
- support dynamic VLAN
- add panic handler for resetting the firmware state
- DebugFS support for datapath statistics
- WCN7850: support for Wake on WLAN
- Microchip (wilc1000):
- read MAC address during probe to make it visible to user space
- suspend/resume improvements
- TI (wl18xx):
- support newer firmware versions
- RealTek (rtw89):
- preparation for RTL8852BE-VT support
- Wake on WLAN support for WiFi 6 chips
- 36-bit PCI DMA support
- RealTek (rtlwifi):
- RTL8192DU support
- Broadcom (brcmfmac):
- Management Frame Protection support (to enable WPA3)
- Bluetooth:
- qualcomm: use the power sequencer for QCA6390
- btusb: mediatek: add ISO data transmission functions
- hci_bcm4377: add BCM4388 support
- btintel: add support for BlazarU core
- btintel: add support for Whale Peak2
- btnxpuart: add support for AW693 A1 chipset
- btnxpuart: add support for IW615 chipset
- btusb: add Realtek RTL8852BE support ID 0x13d3:0x3591"
* tag 'net-next-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1589 commits)
eth: fbnic: Fix spelling mistake "tiggerring" -> "triggering"
tcp: Replace strncpy() with strscpy()
wifi: ath12k: fix build vs old compiler
tcp: Don't access uninit tcp_rsk(req)->ao_keyid in tcp_create_openreq_child().
eth: fbnic: Write the TCAM tables used for RSS control and Rx to host
eth: fbnic: Add L2 address programming
eth: fbnic: Add basic Rx handling
eth: fbnic: Add basic Tx handling
eth: fbnic: Add link detection
eth: fbnic: Add initial messaging to notify FW of our presence
eth: fbnic: Implement Rx queue alloc/start/stop/free
eth: fbnic: Implement Tx queue alloc/start/stop/free
eth: fbnic: Allocate a netdevice and napi vectors with queues
eth: fbnic: Add FW communication mechanism
eth: fbnic: Add message parsing for FW messages
eth: fbnic: Add register init to set PCIe/Ethernet device config
eth: fbnic: Allocate core device specific structures and devlink interface
eth: fbnic: Add scaffolding for Meta's NIC driver
PCI: Add Meta Platforms vendor ID
net/sched: cls_flower: propagate tca[TCA_OPTIONS] to NL_REQ_ATTR_CHECK
...
|
|
Pull SoC dt updates from Arnd Bergmann:
"The devicetree updates are fairly well spread out across platforms,
with Qualcomm making up about a third of the total.
There are three new SoCs in existing product families this:
- NXP i.MX95 is a variant of i.MX93, now with six Cortex-A55 cores
instead of just two as well as a GPU and more high-speed I/O
devices.
- Qualcomm QCS8550 is a variant of SM8550 for IOT devices
- Airoha EN7581 is a 10G-PON network chip and related to the MT7981
Wireless router chip from its parent Mediatek.
In total there are 58 new machines, including four riscv boards and
eight for 32-bit arm.
The most exciting new addition is probably a pair of laptops based on
the Qualcomm x1e80100 (Snapdragon X1 Elite) chip, the Asus Vivobook
S15 and the Lenovo Yoga Slim7x.
Other noteworthy new additions are:
- A total of 20 Qualcomm based machines, mostly Android devices from
Samsung, Motorola and LG, as well as a wireless router and some
reference designs
- Six NXP i.MX based machines, mostly industrial boards along with
some reference designs
- Mediatek sees some interesting Filogic based routers including the
"OpenWRT One", a few new Chromebooks as well as single-board
computers.
- Four machines from Solidrun based on Marvell cn913x, replacing the
older Armada 8000 based counterparts
- The four Amlogic machines are all set top boxes or reference
designs for them
- The nine new Rockchips machines are mostly single-board computers
including some interesting ones based on the rk3588 chip like the
ROCK 5 ITX board and the CM3588 with its four NVMe slots
- The RISC-V boards are all single-board computers based on Starfive
JH7110, Microchip MPFS and Allwinner D1, which all had similar
boards already
There are also a lot of updates to already supported machines, notably
for the TI K3, Rockchips, Freescale and of course Qualcomm platforms"
* tag 'soc-dt-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (846 commits)
arm64: dts: allwinner: h616: add crypto engine node
riscv: dts: add clock generator for Sophgo SG2042 SoC
arm64: dts: rockchip: Add Xunlong Orange Pi 3B
dt-bindings: arm: rockchip: Add Xunlong Orange Pi 3B
arm64: dts: rockchip: Add Radxa ROCK 3B
dt-bindings: arm: rockchip: Add Radxa ROCK 3B
mailmap: Update Luca Weiss's email address
ARM: dts: ixp4xx: nslu2: beeper uses PWM
arm64: dts: rockchip: add ROCK 5 ITX board
dt-bindings: arm: rockchip: Add ROCK 5 ITX board
arm64: dts: rockchip: Add dma-names to uart1 on Pine64 rk3566 devices
arm64: dts: rockchip: Add avdd supplies to hdmi on rock64
arm64: dts: qcom: msm8916-lg-c50: add initial dts for LG Leon LTE
arm64: dts: qcom: msm8916-lg-m216: Add initial device tree
dt-bindings: arm: qcom: Add msm8916 based LG devices
ARM: dts: qcom: msm8960: correct memory base
arm64: dts: qcom: ipq9574: Add icc provider ability to gcc
dt-bindings: interconnect: Add Qualcomm IPQ9574 support
arm64: dts: qcom: sm8150: Add video clock controller node
arm64: dts: qcom: pm6150: Add vibrator
...
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/phy/aquantia/aquantia.h
219343755eae ("net: phy: aquantia: add missing include guards")
61578f679378 ("net: phy: aquantia: add support for PHY LEDs")
drivers/net/ethernet/wangxun/libwx/wx_hw.c
bd07a9817846 ("net: txgbe: remove separate irq request for MSI and INTx")
b501d261a5b3 ("net: txgbe: add FDIR ATR support")
https://lore.kernel.org/all/20240703112936.483c1975@canb.auug.org.au/
include/linux/mlx5/mlx5_ifc.h
048a403648fc ("net/mlx5: IFC updates for changing max EQs")
99be56171fa9 ("net/mlx5e: SHAMPO, Re-enable HW-GRO")
https://lore.kernel.org/all/20240701133951.6926b2e3@canb.auug.org.au/
Adjacent changes:
drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c
4130c67cd123 ("wifi: iwlwifi: mvm: check vif for NULL/ERR_PTR before dereference")
3f3126515fbe ("wifi: iwlwifi: mvm: add mvm-specific guard")
include/net/mac80211.h
816c6bec09ed ("wifi: mac80211: fix BSS_CHANGED_UNSOL_BCAST_PROBE_RESP")
5a009b42e041 ("wifi: mac80211: track changes in AP's TPE")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
string on edgeble-neu2
The rtl82xx DT bindings do not require ethernet-phy-ieee802.3-c22
as the fallback compatible string. There are fewer users of the
Realtek PHY compatible string with fallback compatible string than
there are users without fallback compatible string, so drop the
fallback compatible string from the few remaining users:
$ git grep -ho ethernet-phy-id001c....... | sort | uniq -c
1 ethernet-phy-id001c.c816",
2 ethernet-phy-id001c.c915",
2 ethernet-phy-id001c.c915";
5 ethernet-phy-id001c.c916",
13 ethernet-phy-id001c.c916";
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202406290316.YvZdvLxu-lkp@intel.com/
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240630034910.173552-1-marex@denx.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
'#sound-dai-cells' is required to properly interpret
the list of DAI specified in the 'sound-dai' property,
so add them to the 'hdmi' node for 'rk3128.dtsi'.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/9d0fabb0-70b0-4b4b-ac7c-389b1c7afe20@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
'#sound-dai-cells' is required to properly interpret
the list of DAI specified in the 'sound-dai' property,
so add them to the 'hdmi' node for 'rk3036.dtsi'.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/55d302e5-c018-4b93-84c1-8cf75162e939@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Enable the hdmi_sound node and add i2s0 as sound source
for mk808 hdmi.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/aa79ff87-ea94-4f6d-a81b-5110724243f4@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add the Serial Flash Controller and it's pincontrols.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20240606143401.32454-7-knaerzche@gmail.com
[reference HCLK_SFC by its numeric id to prevent conflicts with the
clock binding/controller changes]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add hdmi-sound node to rk3066a.dtsi, so that it
can be reused by boards with HDMI support.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/5fe7c2fe-4a38-436a-8017-66989959329a@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The SoC has a S/PDIF TX controller which is fully compatible with older
generation Rockchip SoCs.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20240506155103.206592-3-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
RK3128 SoCs have two i2s controllers. i2s_8ch has 8 tx and 2 rx channels
and is internally hard-wired to the hdmi-controller respectivly the SoC's
analog codec. i2s_2ch has 2 tx and 2 rx channels and can also be used
externally as it's pins are exposed though pinctrl.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20240506155103.206592-2-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add the Designware MIPI DSI controller and it's port nodes.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20240509140653.168591-8-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The InnoSilicon D-PHY found in RK3128 SoCs supports DSI/LVDS/TTL with a
maximum transfer rate of 1 Gbps per lane. While adding it, also add it's
clocks to RK3128_PD_VIO powerdomain as the phy is part of it.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20240509140653.168591-7-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
In the combined DT of rk3066a/rk3188 the emac node uses as place holder
the compatible string "snps,arc-emac". The last real user nSIM_700
of the "snps,arc-emac" compatible string in a driver was removed in 2019.
Rockchip emac nodes don't make use of this common fall back string.
In order to removed unused driver code replace this string with
"rockchip,rk3066-emac".
As we are there remove the blank lines and sort.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'#sound-dai-cells' is required to properly interpret
the list of DAI specified in the 'sound-dai' property,
so add them to the 'hdmi' node for 'rk3066a.dtsi'.
Fixes: fadc78062477 ("ARM: dts: rockchip: add rk3066 hdmi nodes")
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/8b229dcc-94e4-4bbc-9efc-9d5ddd694532@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into soc/dt
Small Sonoff iHost improvements (wifi and mmc aliases)
* tag 'v6.9-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Wifi improvements for Sonoff iHost
ARM: dts: rockchip: mmc aliases for Sonoff iHost
Link: https://lore.kernel.org/r/3258282.tdWV9SEqCh@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into soc/dt
Display output for rk3128 and some adaptions to binding clarifications
for hdmi nodes on some older socs.
* tag 'v6.9-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: fix rk322x hdmi ports node
ARM: dts: rockchip: fix rk3288 hdmi ports node
ARM: dts: rockchip: Enable HDMI output for XPI-3128
ARM: dts: rockchip: Add HDMI node for RK3128
ARM: dts: rockchip: Add display subsystem for RK3128
Link: https://lore.kernel.org/r/37970455.XM6RcZxFsP@diego
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
In some instances the kernel fails to detect the sdio wifi module
in the Sonoff iHost.
Tweak sdio properties to improve detection of rtl8723ds wifi module
Signed-off-by: Tim Lunn <tim@feathertop.org>
Link: https://lore.kernel.org/r/20240215110425.934740-3-tim@feathertop.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add aliases for sdio and sdmmc to ensure consistent ordering of
mmc devices on boot
Signed-off-by: Tim Lunn <tim@feathertop.org>
Link: https://lore.kernel.org/r/20240215110425.934740-2-tim@feathertop.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Fix rk322x hdmi ports node so that it matches the
rockchip,dw-hdmi.yaml binding.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/9b84adf0-9312-47fd-becc-cadd06941f70@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Fix rk3288 hdmi ports node so that it matches the
rockchip,dw-hdmi.yaml binding with some reordering
to align with the (new) documentation about
property ordering.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/cc3a9b4f-076d-4660-b464-615003b6a066@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The binding doesn't define interrupts and adding such a definition was
refused because it's unclear how they should ever be used and the
relevant registers are outside the PWM range. So drop them fixing
several dtbs_check warnings like:
arch/arm/boot/dts/rockchip/rv1108-elgin-r1.dtb: pwm@10280030: 'interrupts' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/pwm/pwm-rockchip.yaml#
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240129113205.2453029-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add an hdmi-connector node and enable the hdmi, display-subsystem and vop
nodes.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20231222174220.55249-30-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
RK3128 has Innosilicon based HDMI TX controller similar to the one found in
RK3036.
Add it and the respective port nodes to the SoC device tree.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20231222174220.55249-29-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add vop and display-subsystem nodes to RK3128's device tree.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Link: https://lore.kernel.org/r/20231222174220.55249-28-knaerzche@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Pull SoC DT updates from Arnd Bergmann:
"There is one new SoC for each 32-bit Arm and 64-bit RISC-V, but both
the Rockchips rv1109 and Sopgho CV1812H are just minor variations of
already supported chips.
The other six new SoCs are all part of existing arm64 families, but
are somewhat more interesting:
- Samsung ExynosAutov920 is an automotive chip, and the first one we
support based on the Cortex-A78AE core with lockstep mode.
- Google gs101 (Tensor G1) is the chip used in a number of Pixel
phones, and is grouped with Samsung Exynos here since it is based
on the same SoC design, sharing most of its IP blocks with that
series.
- MediaTek MT8188 is a new chip used for mid-range tablets and
Chromebooks, using two Cortex-A78 cores where the older MT8195 had
four of them.
- Qualcomm SM8650 (Snapdragon 8 Gen 3) is their current top range
phone SoC and the first supported chip based on Cortex-X4,
Cortex-A720 and Cortex-A520.
- Qualcomm X1E80100 (Snapdragon X Elite) in turn is the latest Laptop
chip using the custom Oryon cores.
- Unisoc UMS9620 (Tanggula 7 series) is a 5G phone SoC based on
Cortex-A76 and Cortex-A55
In terms of boards, we have
- Five old Microsoft Lumia phones, the HTC One Mini 2, Motorola Moto
G 4G, and Huawei Honor 5X/GR5, all based on Snapdragon SoCs.
- Multiple Rockchips mobile gaming systems (Anbernic RG351V, Powkiddy
RK2023, Powkiddy X55) along with the Sonoff iHost Smart Home Hub
and a few Rockchips SBCs
- Some ComXpress boards based on Marvell CN913x, which is the
follow-up to Armada 7xxx/8xxx.
- Six new industrial/embedded boards based on NXP i.MX8 and i.MX9
- Mediatek MT8183 based Chromebooks from Lenovo, Asus and Acer.
- Toradex Verdin AM62 Mallow carrier for TI AM62
- Huashan Pi board based on the SophGo CV1812H RISC-V chip
- Two boards based on Allwinner H616/H618
- A number of reference boards for various added SoCs from Qualcomm,
Mediatek, Google, Samsung, NXP and Spreadtrum
As usual, there are cleanups and warning fixes across all platforms as
well as added features for several of them"
* tag 'soc-dt-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (857 commits)
ARM: dts: usr8200: Fix phy registers
arm64: dts: intel: minor whitespace cleanup around '='
arm64: dts: socfpga: agilex: drop redundant status
arm64: dts: socfpga: agilex: add unit address to soc node
arm64: dts: socfpga: agilex: move firmware out of soc node
arm64: dts: socfpga: agilex: move FPGA region out of soc node
arm64: dts: socfpga: agilex: align pin-controller name with bindings
arm64: dts: socfpga: stratix10_swvp: drop unsupported DW MSHC properties
arm64: dts: socfpga: stratix10_socdk: align NAND chip name with bindings
arm64: dts: socfpga: stratix10: add unit address to soc node
arm64: dts: socfpga: stratix10: move firmware out of soc node
arm64: dts: socfpga: stratix10: move FPGA region out of soc node
arm64: dts: socfpga: stratix10: align pincfg nodes with bindings
arm64: dts: socfpga: stratix10: add clock-names to DWC2 USB
arm64: dts: socfpga: drop unsupported cdns,page-size and cdns,block-size
ARM: dts: socfpga: align NAND controller name with bindings
ARM: dts: socfpga: drop unsupported cdns,page-size and cdns,block-size
arm64: dts: rockchip: Fix led pinctrl of lubancat 1
arm64: dts: rockchip: correct gpio_pwrctrl1 typo on nanopc-t6
arm64: dts: rockchip: correct gpio_pwrctrl1 typo on rock-5b
...
|
|
This should be a per board property, should not be put in
a soc core dtsi.
And when this property convert from default-sample-phase
in linux-5.7 by commit 8a385eb57296 ("ARM: dts: rockchip: fix
rockchip,default-sample-phase property names"), the emmc
on rk3036 kylin board get a initialising error:
[ 4.512797] Freeing unused kernel memory: 8192K
[ 4.519500] mmc_host mmc1: Bus speed (slot 0) = 37125000Hz (slot req 37500000Hz, actual 37125000HZ div = 0)
[ 4.530971] mmc1: error -84 whilst initialising MMC card
[ 4.537277] Run /init as init process
[ 4.550932] mmc_host mmc1: Bus speed (slot 0) = 300000Hz (slot req 300000Hz, actual 300000HZ div = 0)
[ 4.664717] mmc_host mmc1: Bus speed (slot 0) = 37125000Hz (slot req 37500000Hz, actual 37125000HZ div = 0)
[ 4.676156] mmc1: error -84 whilst initialising MMC card
I think the reason why the emmc on rk3036 kylin board was able
to work before linux-5.7 was that the illegal property was not
correctly identified by the rockchip dw_mmc driver.
Fixes: faea098e1808 ("ARM: dts: rockchip: add core rk3036 dtsi")
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20231218105523.2478315-4-andyshrk@163.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|