| Age | Commit message (Collapse) | Author |
|---|
|
Pull SoC devicetree updates from Arnd Bergmann:
"There are 11 newly supported SoCs, but these are all either new
variants of existing designs, or straight reuses of the existing chip
in a new package:
- RK3562 is a new chip based on the old Cortex-A53 core, apparently a
low-cost version of the Cortex-A55 based RK3568/RK3566.
- NXP i.MX94 is a minor variation of i.MX93/i.MX95 with a different
set of on-chip peripherals.
- Renesas RZ/V2N (R9A09G056) is a new member of the larger RZ/V2
family
- Amlogic S6/S7/S7D
- Samsung Exynos7870 is an older chip similar to Exynos7885
- WonderMedia wm8950 is a minor variation on the wm8850 chip
- Amlogic s805y is almost idential to s805x
- Allwinner A523 is similar to A527 and T527
- Qualcomm MSM8926 is a variant of MSM8226
- Qualcomm Snapdragon X1P42100 is related to R1E80100
There are also 65 boards, including reference designs for the chips
above, this includes
- 12 new boards based on TI K3 series chips, most of them from
Toradex
- 10 devices using Rockchips RK35xx and PX30 chips
- 2 phones and 2 laptops based on Qualcomm Snapdragon designs
- 10 NXP i.MX8/i.MX9 boards, mostly for embedded/industrial uses
- 3 Samsung Galaxy phones based on Exynos7870
- 5 Allwinner based boards using a variety of ARMv8 chips
- 9 32-bit machines, each based on a different SoC family
Aside from the new hardware, there is the usual set of cleanups and
newly added hardware support on existing machines, for a total of 965
devicetree changesets"
* tag 'soc-dt-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (956 commits)
MAINTAINERS, mailmap: update Sven Peter's email address
arm64: dts: renesas: rzg3e-smarc-som: Reduce I2C2 clock frequency
arm64: dts: nuvoton: Add pinctrl
ARM: dts: samsung: sp5v210-aries: Align wifi node name with bindings
arm64: dts: blaize-blzp1600: Enable GPIO support
dt-bindings: clock: socfpga: convert to yaml
arm64: dts: rockchip: move rk3562 pinctrl node outside the soc node
arm64: dts: rockchip: fix rk3562 pcie unit addresses
arm64: dts: rockchip: move rk3528 pinctrl node outside the soc node
arm64: dts: rockchip: remove a double-empty line from rk3576 core dtsi
arm64: dts: rockchip: move rk3576 pinctrl node outside the soc node
arm64: dts: rockchip: fix rk3576 pcie unit addresses
arm64: dts: rockchip: Drop assigned-clock* from cpu nodes on rk3588
arm64: dts: rockchip: Add missing SFC power-domains to rk3576
Revert "arm64: dts: mediatek: mt8390-genio-common: Add firmware-name for scp0"
arm64: dts: mediatek: mt8188: Address binding warnings for MDP3 nodes
arm64: dts: mt6359: Rename RTC node to match binding expectations
arm64: dts: mt8365-evk: Add goodix touchscreen support
arm64: dts: mediatek: mt8188: Add missing #reset-cells property
arm64: dts: airoha: en7581: Add PCIe nodes to EN7581 SoC evaluation board
...
|
|
Add initial support for PHYTEC phyBOARD-Nash-i.MX93 board [1] based on
the PHYTEC phyCORE-i.MX93 SoM (System-on-Module) [2].
Supported board features:
* ADC
* CAN
* Ethernet
* EEPROM
* RTC
* RS-232/RS-485
* SD-card
* TPM 2.0
* USB
For more details see the product pages for the development kit and the
SoM:
[1] https://www.phytec.eu/en/produkte/development-kits/phyboard-nash/
[2] https://www.phytec.eu/en/produkte/system-on-modules/phycore-imx-91-93/
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix SD card timeout issue caused by LDO5 regulator getting disabled
after boot.
The kernel log shows LDO5 being disabled, which leads to a timeout
on USDHC2:
[ 33.760561] LDO5: disabling
[ 81.119861] mmc1: Timeout waiting for hardware interrupt.
To prevent this, set regulator-boot-on and regulator-always-on for
LDO5. Also add the vqmmc regulator to properly support 1.8V/3.3V
signaling for USDHC2 using a GPIO-controlled regulator.
Fixes: 6c2a1f4f71258 ("arm64: dts: imx8mp-var-som-symphony: Add Variscite Symphony board and VAR-SOM-MX8MP SoM")
Signed-off-by: Himanshu Bhavani <himanshu.bhavani@siliconsignals.io>
Acked-by: Tarang Raval <tarang.raval@siliconsignals.io>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use generic node name for the SoM GPIO expander, following the
Devicetree Specification generic node names recommendation.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add gpio expander node to the device tree and the related nodes.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the embedded controller node to the device tree, this is required
for reset and power-off functionalities.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Configure correctly the FAN pwm output (inverted).
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Using the MDIO pins with Open Drain causes spec violations of the
signals. Revert the changes.
This is similar to commit 14e66e4b13221 ("Revert "arm64: dts:
imx93-tqma9352-mba93xxca: enable Open Drain for MDIO"")
Fixes: e5bc07026f94 ("arm64: add initial device tree for TQMa93xx/MBa91xxCA")
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add initial support for TQMa95xxSA module compatible to SMARC-2.
There is a common device tree for all variants with e.g. reduced CPU count.
It supports LPUART7 for console, CAN, PCIe I2C, SPI, USB3.0, USB2.0, Audio,
SDHC1/2 and QSPI as storage.
[1] https://www.tq-group.com/en/products/tq-embedded/arm-architecture/tqma95xxsa/
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since commit 3c3606793f7e ("dt-bindings: wireless: bcm4329-fmac: Use
wireless-controller.yaml schema"), bindings expect 'wifi' as node name:
imx8mm-var-som-symphony.dtb: bcrmf@1: $nodename:0: 'bcrmf@1' does not match '^wifi(@.*)?$'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This adds support for TQMa8XQPS and TQMa8XDPS modules on MB-SMARC-2 board.
As the only difference is the mounted SoC, both module and baseboard
files are shared.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This overlay configures IMX219 MIPI-CSI-2 camera attached to ISP1.
Also add additional overlay both using LVDS display and camera.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This adds an overlay for the supported LVDS display tianma tm070jvhg33.
The LVDS interface is the same as for MBa8MPxL so the already existing
overlay can be reused on this platform.
Signed-off-by: Martin Schmiedel <Martin.Schmiedel@tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the minimal board dts support for i.MX943 EVK. Only the console uart,
SD & eMMC are enabled for linux basic boot.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the minimal dtsi support for i.MX943. i.MX943 is the first SoC of
i.MX94 Family, create a common dtsi for the whole i.MX94 family, and the
specific dtsi part for i.MX943.
The clock, power domain and perf index need to be used by the device nodes
for resource reference, add them along with the dtsi support.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The needed drivers to support PCIe for i.MX 8QXP have been
added.
Configure PCIe for the Colibri iMX8X SoM.
The pcieb block is connected to the on module Wi-Fi/BT module.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Move pinctrl_uart1 to keep nodes in alphabetical order. No functional
changes.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for the carrier-board Micrel KSZ8081 Ethernet PHY. This is a
10/100Mbit PHY connected to the EQOS interface and shares MDIO bus with
the Ethernet PHY located on the SoM (FEC interface).
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for I2S audio found on phyBOARD-Segin-i.MX93. Audio codec
TLV320AIC3007 is connected to SAI1 interface as a DAI master. MCLK is
provided from the SAI's internal audio PLL (19.2 MHz).
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for both USB controllers. Set first controller in OTG mode
(USB micro-AB connector X8) and the second one in host mode (USB type A
connector X7) by default.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for CAN networking on phyBOARD-Segin-i.MX93 via the flexcan1
interface. The CAN PHY chip SN65HVD234D used on the board is compatible
with the TCAN1043 driver using the generic "can-transceiver-phy" and is
capable of up to 1Mbps data rate.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for RTC connected via I2C on phyBOARD-Segin-i.MX93. Set
default RTC by configuring the aliases.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
ERR052021
Implement fix for i.MX 93 silicon errata ERR052021.
ERR052021 uSDHC: Sometimes uSDHC does not work under VDD_SOC low
drive mode and nominal mode
Description:
uSDHC PADs have one integration issue.
When CMD/DATA lines direction change from output to input, uSDHC
controller begin sampling, the integration issue will make input
enable signal from uSDHC propagated to the PAD with a long delay,
thus the new input value on the pad comes to uSDHC lately. The
uSDHC sampled the old input value and the sampling result is wrong.
Workaround:
Set uSDHC CMD/DATA PADs iomux register SION bit to 1, then PADs will
propagate input to uSDHC with no delay, so correct value is sampled.
This issue will wrongly trigger the start bit when sample the USDHC
command response, cause the USDHC trigger command CRC/index/endbit
error, which will finally impact the tuning pass window, especially
will impact the standard tuning logic, and can't find a correct delay
cell to get the best timing.
Based on commit bb89601282fc ("arm64: dts: imx93-11x11-evk: set SION for
cmd and data pad of USDHC").
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Until now, all usdhc2 (SD-card) pinctrl labels pointed to one pinctrl
group "usdhc2grp" which was overwritten twice by the 100 and 200 MHz
modes. Fix this by using unique pinctrl names.
Additionally, adjust MX93_PAD_SD2_CLK__USDHC2_CLK pad drive-strength
according to values obtained by measurements from the PHYTEC hardware
department to improve signal integrity.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add disable-wp flag (write-protect) to usdhc2 node (SD-card) to get rid
of the following kernel boot warning:
host does not support reading read-only switch, assuming write-enable
Micro SD cards can't be physically write-protected like full-sized
cards anyways.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Drop redundant 'no-1-8-v' flag from usdhc1 (eMMC) node. Flag is now set
by default in the SOM include file (imx93-phycore-som.dtsi).
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The phyCORE-i.MX93 SoM comes in two variants, one with VDD_IO set to
3.3V and the other variant to 1.8V. The 3.3V variant can only support
DDR52 mode, while 1.8V variant is capable of HS400ES eMMC mode. The
information about VDD_IO option is encoded in the SoM's EEPROM. EEPROM
is read in the bootloader and bootloader clears the "no-1-8-v" flag in
case of 1.8V SoM variant is detected. Thus add property 'no-1-8-v' by
default to usdhc1 (eMMC) node and let bootloader handle the flag. In
case EEPROM is erased or read-out fails, flag "no-1-8-v" also ensures
fall-back compatibility with both SoM variants.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Improve eMMC on phyCORE-i.MX93 SOM by adding 100MHz and 200MHz pinctrl
modes. This enables to use eMMC at enhanced data rates (e.g. HS400).
While at it, apply a workaround for the i.MX93 chip errata ERR052021.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There is already an external pull-down resistor on the LED output line.
It makes no sense to have both pull-down and pull-up resistors enabled
at the same time. Thus disable the internal pull-up.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for the EEPROM chip available on I2C3 bus (address 0x50),
used for the PHYTEC SOM detection.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
PMIC driver for PCA9451A used on phyCORE-i.MX93 SOM is available since
commit 5edeb7d31262 ("regulator: pca9450: add pca9451a support"). Add
support for it in the SOM device-tree.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
When running in nominal drive mode, the maximum allowed frequency for
the NoC is 800MHz, but the OPP table for the i.MX8MP interconnect device
listed the 1GHz operating point for the NoC, regardless of the active
mode.
The newly introduced imx8mp-nominal.dtsi header reconfigures the clock
controller to observe nominal drive mode limits, so have it modify the
maximum NoC OPP as well.
Fixes: 255fbd9eabe7 ("arm64: dts: imx8mp: Add optional nominal drive mode DTSI")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Libra board has an LVDS connector. Add an overlay for an
etml1010g3dra LVDS panel supported for the phyCORE-i.MX 8M Plus that may
be connected to it.
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add device tree for the Libra-i.MX 8M Plus FPSC board. The Libra is a
pure development board and has hardware to support FPSC-24-A.0 set of
features. It can be populated with the phyCORE-i.MX 8M Plus SoM to form
a SBC.
The phyCORE-i.MX 8M Plus FPSC [1] SoM uses only a subset of the hardware
features the Libra board provides. The phyCORE-i.MX8MP FPSC itself is a
System on Module based on the i.MX 8M Plus SoC utilizing the Future
Proof Solder Core [2] standard.
To be able to easily map FPSC interface names to SoC interfaces, the
FPSC interface names are added as inline comments. Example:
&i2c5 { /* FPSC I2C4 */
pinctrl-0 = <&pinctrl_i2c5>;
[...]
};
Here, I2C4 is the FPSC interface name. The i2c5 instance of the i.MX 8M Plus
SoC is used to fulfill the i2c functionality and its signals are routed
to the FPSC I2C4 signal pins:
pinctrl_i2c5: i2c5grp {
fsl,pins = <
MX8MP_IOMUXC_SPDIF_RX__I2C5_SDA 0x400001c2 /* I2C4_SDA */
MX8MP_IOMUXC_SAI5_RXD0__I2C5_SCL 0x400001c2 /* I2C4_SCL */
>;
};
The features are almost identical to the existing phyCORE-i.MX 8M Plus
SoM (dts: imx8mp-phycore-som.dtsi), but the pin muxing is different due
to the FPSC standard as well as 1.8V IO voltage instead of 3.3V.
[1] https://www.phytec.eu/en/produkte/system-on-modules/phycore-imx-8m-plus-fpsc/
[2] https://www.phytec.eu/en/produkte/system-on-modules/fpsc/
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Define vqmmc regulator-gpio for usdhc2 with vin-supply
coming from LDO5.
Without this definition LDO5 will be powered down, disabling
SD card after bootup. This has been introduced in commit
f5aab0438ef1 ("regulator: pca9450: Fix enable register for LDO5").
Fixes: 6a57f224f734 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Fixes: f5aab0438ef1 ("regulator: pca9450: Fix enable register for LDO5")
Tested-by: Manuel Traut <manuel.traut@mt.com>
Reviewed-by: Philippe Schenker <philippe.schenker@impulsing.ch>
Tested-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Cc: stable@vger.kernel.org
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@mt.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add pcie[0,1]-ep nodes and apply imx-pcie1-ep overlay file.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add pcie0-ep node for i.MX8QM.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add pcie0-ep node information and apply pcie0-ep overlay file.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Create imx95-15x15-evk pcie0-ep and imx95-19x19-evk pcie[0,1]-ep dtb files.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use common imx-pcie0-ep.dtso for imx8mp-evk-pcie-ep and
imx8qxp-mek-pcie-ep. No functional change.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use unified pcie0 label and add pcie0-ep node.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
i.MX8DXL use difference irq number for PCIe EP DMA.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add unified pcie<n> and pcie<n>_ep label for existed chipes to prepare
applied one overay file to enable EP function.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The needed drivers to support PCIe and SATA for i.MX 8QM have been
added.
Configure them for the Apalis iMX8 SoM.
The pciea and pcieb blocks each get a single PCIe lane, pciea is
available on the carrier boards while pcieb is connected to the
on module Wi-Fi/BT module.
The SATA lane is available on the carrier boards.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Using the MDIO pins with Open Drain causes spec violations of the
signals. Revert the changes.
This reverts commit 315d7f301e234b99c1b9619f0b14cf288dc7c33f.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Using the MDIO pins with Open Drain causes spec violations of the
signals. Revert the changes.
This reverts commit 9015397c2f2d9d327c0cf88d74e39c4858cb4912.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable the interrupts and wakeup-source to allow the external RTC to be
used as an alarm.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable the interrupts and wakeup-source to allow the external RTC to be
used as an alarm.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable the interrupts and wakeup-source to allow the external RTC to be
used as an alarm.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Ethernet PHY setup currently assumes that the bootloader will take the
PHY out of reset, but this behavior is not guaranteed across all
bootloaders. Add the reset GPIO to ensure the kernel can properly control
the PHY reset line.
Also configure the PHY IRQ GPIO to enable interrupt-driven link status
reporting, instead of relying on polling.
This ensures more reliable Ethernet initialization and improves PHY event
handling.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
