| Age | Commit message (Collapse) | Author |
|---|
|
Add subnode usb_con: extcon for SM5502 / SM5504 MUIC, which will be used
for RT5033 charger.
Signed-off-by: Raymond Hackley <raymondhackley@protonmail.com>
Link: https://lore.kernel.org/r/20240215122605.3817-1-raymondhackley@protonmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Enable sound and modem for the Samsung A2015 based devices (A3, A5, E5,
E7, Grand Max). The setup is similar to most MSM8916 devices, i.e.:
- QDSP6 audio
- Earpiece/headphones/microphones via digital/analog codec in
MSM8916/PM8916
- WWAN Internet via BAM-DMUX
except:
- NXP TFA9895 codec for speaker on Quaternary MI2S
- Samsung-specific audio jack detection (not supported yet)
[Lin: Add e2015 and grandmax]
Co-developed-by: "Lin, Meng-Bo" <linmengbo0689@protonmail.com>
Signed-off-by: "Lin, Meng-Bo" <linmengbo0689@protonmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20231003-msm8916-modem-v2-5-61b684be55c0@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Now that we no longer have fixed addresses for the firmware memory
regions, disable them by default and only enable them together with
the actual user in the board DT.
This frees up unnecessary reserved memory for boards that do not use
some of the remoteprocs and allows moving selected device-specific
properties (such as firmware size) to the board-specific DT part in
the next step.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20230911-msm8916-rmem-v1-7-b7089ec3e3a1@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
MSM8916/39 do not need signed GPU firmware so it is generally okay to
have it enabled by default. However, currently the GPU does not work
without also enabling MDSS and it's questionable if someone would
really need it without a display in practice.
For consistency let's follow newer SoCs and disable the GPU by default.
Enable it for all existing devices that already have &mdss enabled.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20230911-msm8916-rmem-v1-2-b7089ec3e3a1@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Venus needs firmware that is usually signed with a device-specific key.
There are also devices that might not need it (especially during
bring-up), so let's follow more recent SoCs and disable it by default.
Enable it explicitly for all current devices except msm8916-mtp. That
one has just UART enabled currently so it cannot really benefit from
Venus.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20230911-msm8916-rmem-v1-1-b7089ec3e3a1@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
MSM8939 has the SDC pinctrl consolidated in two &sdcN_default and
&sdcN_sleep states, while MSM8916 has all pins separated. Make this
consistent by consolidating them for MSM8916 well.
Use this as a chance to define default pinctrl in the SoC.dtsi and only
let boards that add additional definitions (such as cd-gpios) override it.
For MSM8939 just make the label consistent with the other pinctrl
definitions (they do not have a _state suffix).
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230529-msm8916-pinctrl-v1-2-11f540b51c93@gerhold.net
|
|
The current SD card detect pinctrl setup configures bias-pull-up for
the "default" (active) case and bias-disable for the "sleep" case.
Before commit b5c833b703cc ("mmc: sdhci-msm: Set IO pins in low power
state during suspend") the pull up was permanently active. Since then
it is only active when a valid SD card is inserted.
This does not really make sense: For an active-low CD, the pull up is
needed to pull the GPIO high when the card is not inserted. When the
card gets inserted CD is shorted to ground (low). This means right now
the pull-up is removed exactly when it is needed to detect the next
card insertion. Generally, applying different bias for CD does not
really make sense. It should always stay the same so card removals and
insertions can be detected properly.
The reason why card detection still works fine in practice is that most
boards seem to have external pull up on the CD pin. However, this means
that there is no need to configure an internal pull-up at all and we
can keep bias-disable permanently.
There are also some boards with different CD polarity (acer-a1-724) and
with different GPIO number (huawei-g7). All in all this makes it
obvious that the CD pin is board-specific and the pinctrl for it should
be defined in the board DT.
Move it to the boards that need it and use bias-disable permanently for
the boards that seem to have external pull-up. The vendor device tree
for msm8939-sony-xperia-kanuti-tulip suggests that it needs the
internal pull-up permanently [1] so it gets bias-pull-up to be sure.
[1]: https://github.com/sonyxperiadev/kernel/blob/57b5050e340f40a88e1ddb8d16fd9adb44418923/arch/arm/boot/dts/qcom/msm8939-kanuti_tulip.dtsi#L634-L636
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230529-msm8916-pinctrl-v1-1-11f540b51c93@gerhold.net
|
|
MSM8939 has the aliases defined separately for each board (because
there could be (theoretically) a board where the slots are numbered
differently. To make MSM8916 and MSM8939 more consistent do the same
for all MSM8916 boards and move aliases there.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230525-msm8916-labels-v1-6-bec0f5fb46fb@gerhold.net
|
|
Right now MDSS related definitions cannot be properly grouped together
in board DTs because the labels do not use consistent prefixes. The DSI
PHY label is particularly weird because the DSI number is at the end
(&dsi_phy0) while DSI itself is called &dsi0.
Follow the example of more recent SoCs and give all the MDSS related
nodes a consistent label that allows proper grouping.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230525-msm8916-labels-v1-4-bec0f5fb46fb@gerhold.net
|
|
For some reason the BLSP UART controllers have a label with a number
behind blsp (&blsp1_uartN) while I2C/SPI are named without (&blsp_i2cN).
This is confusing, especially for proper node ordering in board DTs.
Right now all board DTs are ordered as if the number behind blsp does
not exist (&blsp_i2cN comes before &blsp1_uartN). Strictly speaking
correct ordering would be the other way around ('1' comes before '_').
End this confusion by giving the UART controllers consistent labels.
There is just one BLSP on MSM8916/39 so the number is redundant.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230525-msm8916-labels-v1-2-bec0f5fb46fb@gerhold.net
|
|
MSM8916 is the only ARM64 Qualcomm SoC that is still using the old
&msmgpio name. Change this to &tlmm to avoid confusion.
Note that the node ordering does not change because the MSM8916 device
trees have pinctrl separated at the bottom (similar to sc7180).
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230525-msm8916-labels-v1-1-bec0f5fb46fb@gerhold.net
|
|
Right now each MSM8916 device has a huge block of regulator constraints
with allowed voltages for each regulator. For lack of better
documentation these voltages are often copied as-is from the vendor
device tree, without much extra thought.
Unfortunately, the voltages in the vendor device trees are often
misleading or even wrong, e.g. because:
- There is a large voltage range allowed and the actual voltage is
only set somewhere hidden in some messy vendor driver. This is often
the case for pm8916_{l14,l15,l16} because they have a broad range of
1.8-3.3V by default.
- The voltage is actually wrong but thanks to the voltage constraints
in the RPM firmware it still ends up applying the correct voltage.
To have proper regulator constraints it is important to review them in
context of the usage. The current setup in the MSM8916 device trees
makes this quite hard because each device duplicates the standard
voltages for components of the SoC and mixes those with minor
device-specific additions and dummy voltages for completely unused
regulators.
The actual usage of the regulators for the SoC components is in
msm8916-pm8916.dtsi, so it can and should also define the related
voltage constraints. These are not board-specific but defined in the
APQ8016E/PM8916 Device Specification. The board DT can then focus on
describing the actual board-specific regulators, which makes it much
easier to review and spot potential mistakes there.
Note that this commit does not make any functional change. All used
regulators still have the same regulator constraints as before. Unused
regulators do not have regulator constraints anymore because most of
these were too broad or even entirely wrong. They should be added back
with proper voltage constraints when there is an actual usage.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-7-54d4960a05fc@gerhold.net
|
|
The regulator constraints for most MSM8916 devices (except DB410c) were
originally taken from Qualcomm's msm-3.10 vendor device tree (for lack
of better documentation). Unfortunately it turns out that Qualcomm's
voltages are slightly off as well and do not match the voltage
constraints applied by the RPM firmware.
This means that we sometimes request a specific voltage but the RPM
firmware actually applies a much lower or higher voltage. This is
particularly critical for pm8916_l11 which is used as SD card VMMC
regulator: The SD card can choose a voltage from the current range of
1.8 - 2.95V. If it chooses to run at 1.8V we pretend that this is fine
but the RPM firmware will still silently end up configuring 2.95V.
This can be easily reproduced with a multimeter or by checking the
SPMI hardware registers of the regulator.
Fix this by making the voltages match the actual "specified range" in
the PM8916 Device Specification which is enforced by the RPM firmware.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-3-54d4960a05fc@gerhold.net
|
|
On MSM8916 the wireless connectivity functionality (WiFi/Bluetooth) is
split into the digital part inside the SoC and the analog RF part inside
a supplementary WCN36xx chip. For MSM8916, three different options
exist:
- WCN3620 (WLAN 802.11 b/g/n 2.4 GHz + Bluetooth)
- WCN3660B (WLAN 802.11 a/b/g/n 2.4/5 GHz + Bluetooth)
- WCN3680B (WLAN 802.11ac 2.4/5 GHz + Bluetooth)
Choosing one of these is up to the board vendor. This means that the
compatible belongs into the board-specific DT part so people porting
new boards pay attention to set the correct compatible.
Right now msm8916.dtsi sets "qcom,wcn3620" as default compatible,
which does not work at all for boards that have WCN3660B or WCN3680B.
Remove the default compatible from msm8196.dtsi and move it to the board
DT as follows:
- Boards with only &pronto { status = "okay"; } used the default
"qcom,wcn3620" so far. They now set this explicitly for &wcnss_iris.
- Boards with &pronto { ... iris { compatible = "qcom,wcn3660b"; }};
already had an override that just moves to &wcnss_iris now.
- For msm8916-samsung-a2015-common.dtsi the WCN compatible differs for
boards making use of it (a3u: wcn3620, a5u: wcn3660b, e2015: wcn3620)
so the definitions move to the board-specific DT part.
Since this requires touching all the board DTs, use this as a chance to
name the WCNSS-related labels consistently, so everything is grouped
properly when sorted alphabetically.
No functional change, just clean-up for more clarity & easier porting.
Aside from ordering the generated DTBs are identical.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230309091452.1011776-1-stephan.gerhold@kernkonzept.com
|
|
Correct typo in motor pinctrl node name:
msm8916-samsung-a5u-eur.dtb: pinctrl@1000000: 'motor-en-default-stae' does not match any of the regexes: '-state$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221230135645.56401-8-krzysztof.kozlowski@linaro.org
|
|
DT schema expects TLMM pin configuration nodes to be named with
'-state' suffix and their optional children with '-pins' suffix.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221024002356.28261-2-krzysztof.kozlowski@linaro.org
|
|
Both a2015 devices use motor drivers controlled with PWM signal.
A5 additionally has a fixed regulator that powers the driver and is
controlled by enable signal. A3 routes that enable signal to the
motor driver itself.
To simplify the description, add the motor to the common dtsi and
assume a regulator is used for both.
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
[Rename the nodes to be reusable in msm8916-sansung-e2015]
Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221020115255.2026-1-linmengbo0689@protonmail.com
|
|
NFC chip
According to s3fwrn5 driver code the "enable" GPIO line is driven "high"
when chip is not in use (mode is S3FWRN5_MODE_COLD), and is driven "low"
when chip is in use.
s3fwrn5_phy_power_ctrl():
...
gpio_set_value(phy->gpio_en, 1);
...
if (mode != S3FWRN5_MODE_COLD) {
msleep(S3FWRN5_EN_WAIT_TIME);
gpio_set_value(phy->gpio_en, 0);
msleep(S3FWRN5_EN_WAIT_TIME);
}
Therefore the line described by "en-gpios" property should be annotated
as "active low".
The wakeup gpio appears to have correct polarity (active high).
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220929011557.4165216-2-dmitry.torokhov@gmail.com
|
|
reg_vdd_tsp: regulator-vdd-tsp is actually used as an analog regulator for
touchscreen on all of a2015 and e2015 devices.
Rename it into reg_vdd_tsp_a: regulator-vdd-tsp-a to reduce confusion.
Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220724095438.14252-1-linmengbo0689@protonmail.com
|
|
A3, A5 and most of the Samsung phones with MSM8916 SoC use GPIO pin 13 for
touchscreen interrupts. Add touchscreen pinctrl to a2015 common dtsi.
Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220610175332.104154-1-linmengbo0689@protonmail.com
|
|
The node names should be generic and DT schema expects certain pattern
(e.g. with key/button/switch).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220616005333.18491-21-krzysztof.kozlowski@linaro.org
|
|
DT schema expects PMIC GPIO pin configuration nodes to be named with
'-state' suffix. Optional children should be either 'pinconf' or
followed with '-pins' suffix. This fixes dtbs_check warnings like:
sdm845-xiaomi-beryllium.dtb: gpios@c000: 'vol-up-active' does not match any of the regexes: '-state$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220507194913.261121-6-krzysztof.kozlowski@linaro.org
|
|
The Samsung Galaxy A3/A5 both have a Samsung S3FWRN5 NFC chip that
works quite well with the s3fwrn5 driver in the Linux NFC subsystem.
The clock setup for the NFC chip is a bit special (although this
seems to be a common approach used for Qualcomm devices with NFC):
The NFC chip has an output GPIO that is asserted whenever the clock
is needed to function properly. On the A3/A5 this is wired up to
PM8916 GPIO2, which is then configured with a special function
(NFC_CLK_REQ or BB_CLK2_REQ).
Enabling the rpmcc RPM_SMD_BB_CLK2_PIN clock will then instruct
PM8916 to automatically enable the clock whenever the NFC chip
requests it. The advantage is that the clock is only enabled when
needed and we don't need to manage it ourselves from the NFC driver.
Note that for some reason Samsung decided to connect the I2C pins
to GPIOs where no hardware I2C bus is available, so we need to
fall back to software bit-banging with i2c-gpio.
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210604172742.10593-5-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The Samsung Galaxy A3/A5 use a Richtek RT5033 PMIC as battery
fuel gauge, charger, flash LED and for some regulators. For now,
only add the fuel gauge/battery device to the device tree,
so we can check the remaining battery percentage.
The other RT5033 drivers need some more work first before
they can be used properly.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210604172742.10593-4-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
The Samsung Galaxy A3/A5 both have two capacitive touch keys,
connected to an ABOV MCU. It implements the same interface as
implemented by the tm2-touchkey driver and works just fine with
the coreriver,tc360-touchkey compatible. It's probably actually some
Samsung-specific interface that they implement with different MCUs.
Note that for some reason Samsung decided to connect this to GPIOs
where no hardware I2C bus is available, so we need to fall back
to software bit-banging using i2c-gpio.
The vdd/vcc-supply is board-specific and will be added separately
for a3u/a5u.
Co-developed-by: Michael Srba <Michael.Srba@seznam.cz>
Signed-off-by: Michael Srba <Michael.Srba@seznam.cz>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210604172742.10593-1-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Disable MDSS (Mobile Display Subsystem) by default in msm8916.dtsi
and only explicitly enable it in devices' DT which actually use it.
This leads to faster boot and cleaner logs for other devices,
which also won't have to explicitly disable MDSS to use framebuffer.
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Link: https://lore.kernel.org/r/20210130105717.2628781-4-vincent.knecht@mailoo.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
When the BMC150 accelerometer/magnetometer was added to the device tree,
the sensors were working without specifying any regulator supplies,
likely because the regulators were on by default and then never turned off.
For some reason, this is no longer the case for pm8916_l17, which prevents
the sensors from working in some cases.
Now that the bmc150_accel/bmc150_magn drivers can enable necessary
regulators, declare the necessary regulator supplies to make the sensors
work again.
Fixes: 079f81acf10f ("arm64: dts: qcom: msm8916-samsung-a2015: Add accelerometer/magnetometer")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210111175358.97171-1-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Some versions of the firmware leave i2c gpios in a wrong state.
Add pinctrl that disables pin bias since external pull-up resistors
are present.
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Fixes: 1329c1ab0730 ("arm64: dts: qcom: Add device tree for Samsung Galaxy A3U/A5U")
Signed-off-by: Nikita Travkin <nikitos.tr@gmail.com>
Link: https://lore.kernel.org/r/20201113175917.189123-6-nikitos.tr@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
s1 (VDDCX) and l3 (VDDMX) are now managed by rpmpd as power domains.
This allows us to vote for voltage corners instead of voting for raw
voltages. But we cannot manage these as regulator and power domain at
the same time: The votes by rpmpd would conflict with the ones from
the regulator driver.
All users of these regulators have been converted to power domains.
Make sure that no new users are added by removing s1 and l3 from
the regulator definitions.
This also allows us to remove the arbitrary voltage constraints
we have been using for these regulators. Not all of the voltages
listed there would actually have been safe for the boards.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200916104135.25085-11-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Now that all MSM8916 boards are referencing nodes by label instead
of name, we can easily make some more nodes use more generic names
(as recommended in the device tree specification or the binding
documentation).
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200915071221.72895-10-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Right now we define "hnp-disable", "srp-disable", "adp-disable"
separately for every MSM8916 board that has USB working.
They are needed for USB to work properly if CONFIG_USB_OTG_FSM
is enabled. This is because the chipidea OTG FSM code waits for
interrupts regarding the VBUS state (AVVIS). Those never happen
on MSM8916 because VBUS is always connected to the PMIC instead
of the USB controller.
There was a patch [1] to work around this but ultimately it was
decided that it's easier to disable the OTG FSM altogether using
these properties. This works fine for most use cases, because the
OTG FSM isn't needed for simple dual role host/gadget operation.
Given that these properties are needed for every MSM8916 device,
move them to msm8916.dtsi so we can avoid some more duplication.
[1]: https://lore.kernel.org/lkml/20160707222114.1673-10-stephen.boyd@linaro.org/
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200720085406.6716-11-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Right now some device nodes set default pinctrl within msm8916.dtsi
(e.g. I2C, SPI), but for others it needs to be explicitly set in the
board-specific device tree (e.g. UART).
While it is theoretically possible that some super special board
needs different pinctrl for these, in practice pretty much every
board ends up using the common pinctrl definitions.
Make this consistent by also defining the common pinctrl properties
for blsp1_uart1 and blsp1_uart2 so we don't need to copy this for every
board. If there is really such a super special board it could just
override these properties with custom pinctrl or make minor modifications
to the common pinctrl configurations provided by msm8916-pins.dtsi.
Also move #address-cells/#size-cells for &dsi0 to msm8916.dtsi
since this is specific to the DSI node, not the board.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200720085406.6716-10-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
So far we had some supplies defined for all boards in msm8916.dtsi,
while others were duplicated into every board-specific device tree.
Now that we have msm8916-pm8916.dtsi as a common include for all
standard MSM8916 devices using PM8916, move the remaining common
supplies to msm8916-pm8916.dtsi to reduce duplication a bit.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200720085406.6716-9-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Device trees for newer SoCs avoid defining the regulator nodes directly
in the SoC device tree (here: msm8916.dtsi). The reason for this is that
theoretically it is possible to combine the SoC with a different PMIC,
or to use all the regulators in a board-specific way.
Therefore let's remove those from the SoC include (msm8916.dtsi).
In practice, pretty much all MSM8916 boards were combined with PM8916,
and use the regulators in similar ways. After looking at many different
MSM8916 boards (mostly smartphones and tablets), I haven't seen a single
device that isn't using the same regulators for components integrated
into the SoC.
If all boards end up defining all regulators and supplies in the same way
then it is useful to have an include for that, so we can avoid duplicating
it everywhere. If there is really a super special board that does it
differently it could just override some properties or avoid using the
include altogether.
This patch moves the regulator and common supply definitions to
a new include called "msm8916-pm8916.dtsi".
This is also going to be useful when introducing CPR (Core Power
Reduction) later because we can configure the CPU regulator
(pm8916_spmi_s2) for all devices in this common include.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200720085406.6716-8-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Right now we define the entire pm8916 resin node separately in
the board-specific device tree part, including the interrupt that
belongs to PM8916.
As a feature of the PMIC it should be declared in pm8916.dtsi,
disabled by default. Like all other optional components it can then
by enabled and configured in the board-specific device tree part.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200720085406.6716-7-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Device trees for newer SoCs avoid replicating the entire device
hierarchy in the board-specific device tree part. Instead,
they set additional properties only by referencing labels,
sorted alphabetically.
Now that we have labels for all relevant nodes, convert the MSM8916
board device trees to use the same style and remove the "soc" node
entirely.
Note: There is a large block of coresight nodes in apq8016-sbc.dtsi,
which are enabled by setting status = "okay". I kept them grouped
together (not alphabetically sorted with everything else),
since that would be just unnecessarily verbose and hard to see.
This commit only moves all existing properties to nodes that reference
the respective label. The resulting binary DTBs are exactly the same.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200720085406.6716-6-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
A3U/A5U both use a Bosch BMC150 accelerometer/magnetometer combo.
The chip provides two separate I2C devices for the accelerometer
and magnetometer that are already supported by the bmc150-accel
and bmc150-magn driver.
The only difference between A3U/A5U is the way the sensor is
mounted on the mainboard - set the mount-matrix in the
device-specific device tree part to handle that difference.
Co-developed-by: Michael Srba <michael.srba@seznam.cz>
Signed-off-by: Michael Srba <michael.srba@seznam.cz>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200622151751.408995-5-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
So far we have been separating pinctrl entries into pinmux/pinconf.
It turns out it is also possible to combine them: The advantage is
that the device tree is overall more concise because the "pins"
to configure just need to be specified once, not separately for
pinmux/pinconf.
Using the simpler form only for new entries would be rather confusing.
This commit makes all MSM8916 device trees use the simplfied form.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200622151751.408995-3-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
It is helpful to be able to see all hardware components in one part
of the device tree, without having to scroll over the large amount
of regulator/pinctrl nodes. Keep those separated at the end of the file
to make navigation a bit easier.
This also makes it consistent with the order used in apq8016-sbc.dtsi.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200622151751.408995-2-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Many nodes in the MSM8916 device trees use '_' in node names
(especially pinctrl), even though (seemingly) '-' is preferred now.
Make this more consistent by replacing '_' with '-' where possible.
Similar naming is used for pinctrl in newer device trees (e.g. sdm845.dtsi).
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200514112754.148919-1-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
This patch wires up display support on Samsung Galaxy A3 2015.
Signed-off-by: Michael Srba <michael.srba@seznam.cz>
Link: https://lore.kernel.org/r/20200514170129.10902-1-michael.srba@seznam.cz
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
On some msm8916 devices, attempts at initializing coresight cause the boot to
fail. This was fixed by disabling the coresight-related nodes in the board dts
files. However, a cleaner approach was chosen for fixing the same issue on
msm8998: disabling coresight by default, and enabling it in board dts files
where desired.
This patch implements the same solution for msm8916, removes now redundant
overwrites in board specific dts files and and enables coresight in db410c's
board dts in order to keep the current behavior.
Fixes: b1fcc5702a41 ("arm64: dts: qcom: msm8916: Add CTI options")
Signed-off-by: Michael Srba <michael.srba@seznam.cz>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Link: https://lore.kernel.org/r/20200513184735.30104-1-michael.srba@seznam.cz
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
A3U and A5U both use an extra touchscreen LDO regulator
that provides 3.3V for the touch screen controller.
Add it as fixed regulator to the common include.
Cc: Michael Srba <Michael.Srba@seznam.cz>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200426140642.204395-4-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
At the moment, writing large amounts of data to the eMMC causes the device
to freeze. The symptoms vary, sometimes the device reboots immediately,
but usually it will just get stuck.
It turns out that the issue is not actually related to the eMMC:
Apparently, Samsung has made some modifications to the TrustZone firmware.
These require additional memory which is reserved at 0x85500000-0x86000000.
The downstream kernel describes this memory reservation as:
/* Additionally Reserved 6MB for TIMA and Increased the TZ app size
* by 2MB [total 8 MB ]
*/
This suggests that it is used for additional TZ apps, although the extra
memory is actually 11 MB instead of the 8 MB mentioned in the comment.
Writing to the protected memory causes the kernel to crash or freeze.
In our case, writing to the eMMC causes the disk cache to fill
the available RAM, until the kernel eventually crashes
when attempting to use the reserved memory.
Add the additional memory as reserved-memory to fix this problem.
Fixes: 1329c1ab0730 ("arm64: dts: qcom: Add device tree for Samsung Galaxy A3U/A5U")
Reported-by: Michael Srba <Michael.Srba@seznam.cz>
Tested-by: Michael Srba <Michael.Srba@seznam.cz> # a3u
Tested-by: Stephan Gerhold <stephan@gerhold.net> # a5u
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20191231112511.83342-1-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add nodes for basic GPIO connected hardware to the Samsung A3/A5 common dtsi.
This includes the Volume UP button, the Home button, and the hall sensor used
to sense "smart cover" open state. Related to that, add a node for the Volume
DOWN button, which is handled by the pm8916 as is common with msm8916 devices.
Tested-by: Stephan Gerhold <stephan@gerhold.net> # a5u
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Michael Srba <Michael.Srba@seznam.cz>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
WCNSS is used on A3U and A5U for WiFi and BT,
and seems to work fine without further changes.
Enable it in the common include.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Samsung Galaxy A3 (SM-A300FU) and Samsung Galaxy A5 (SM-A500FU)
are smartphones using the MSM8916 SoC released in 2015.
Add a device tree for A3U and A5U with initial support for:
- SDHCI (internal and external storage)
- USB Device Mode
- UART (on USB connector via the SM5502 MUIC)
- Regulators
The two devices (and all other variants of A3/A5 released in 2015)
are very similar, with some differences in display, touchscreen
and sensors. The common parts are shared in
msm8916-samsung-a2015-common.dtsi to reduce duplication.
The device tree is loosely based on apq8016-sbc.dtsi and the
downstream kernel provided by Samsung, mixed with a lot of own
research.
Co-developed-by: Michael Srba <Michael.Srba@seznam.cz>
Signed-off-by: Michael Srba <Michael.Srba@seznam.cz>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
