| Age | Commit message (Collapse) | Author |
|---|
|
Pull SoC devicetree updates from Arnd Bergmann:
"There are 11 newly supported SoCs, but these are all either new
variants of existing designs, or straight reuses of the existing chip
in a new package:
- RK3562 is a new chip based on the old Cortex-A53 core, apparently a
low-cost version of the Cortex-A55 based RK3568/RK3566.
- NXP i.MX94 is a minor variation of i.MX93/i.MX95 with a different
set of on-chip peripherals.
- Renesas RZ/V2N (R9A09G056) is a new member of the larger RZ/V2
family
- Amlogic S6/S7/S7D
- Samsung Exynos7870 is an older chip similar to Exynos7885
- WonderMedia wm8950 is a minor variation on the wm8850 chip
- Amlogic s805y is almost idential to s805x
- Allwinner A523 is similar to A527 and T527
- Qualcomm MSM8926 is a variant of MSM8226
- Qualcomm Snapdragon X1P42100 is related to R1E80100
There are also 65 boards, including reference designs for the chips
above, this includes
- 12 new boards based on TI K3 series chips, most of them from
Toradex
- 10 devices using Rockchips RK35xx and PX30 chips
- 2 phones and 2 laptops based on Qualcomm Snapdragon designs
- 10 NXP i.MX8/i.MX9 boards, mostly for embedded/industrial uses
- 3 Samsung Galaxy phones based on Exynos7870
- 5 Allwinner based boards using a variety of ARMv8 chips
- 9 32-bit machines, each based on a different SoC family
Aside from the new hardware, there is the usual set of cleanups and
newly added hardware support on existing machines, for a total of 965
devicetree changesets"
* tag 'soc-dt-6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (956 commits)
MAINTAINERS, mailmap: update Sven Peter's email address
arm64: dts: renesas: rzg3e-smarc-som: Reduce I2C2 clock frequency
arm64: dts: nuvoton: Add pinctrl
ARM: dts: samsung: sp5v210-aries: Align wifi node name with bindings
arm64: dts: blaize-blzp1600: Enable GPIO support
dt-bindings: clock: socfpga: convert to yaml
arm64: dts: rockchip: move rk3562 pinctrl node outside the soc node
arm64: dts: rockchip: fix rk3562 pcie unit addresses
arm64: dts: rockchip: move rk3528 pinctrl node outside the soc node
arm64: dts: rockchip: remove a double-empty line from rk3576 core dtsi
arm64: dts: rockchip: move rk3576 pinctrl node outside the soc node
arm64: dts: rockchip: fix rk3576 pcie unit addresses
arm64: dts: rockchip: Drop assigned-clock* from cpu nodes on rk3588
arm64: dts: rockchip: Add missing SFC power-domains to rk3576
Revert "arm64: dts: mediatek: mt8390-genio-common: Add firmware-name for scp0"
arm64: dts: mediatek: mt8188: Address binding warnings for MDP3 nodes
arm64: dts: mt6359: Rename RTC node to match binding expectations
arm64: dts: mt8365-evk: Add goodix touchscreen support
arm64: dts: mediatek: mt8188: Add missing #reset-cells property
arm64: dts: airoha: en7581: Add PCIe nodes to EN7581 SoC evaluation board
...
|
|
Add PCIe lane equalization preset properties for 8 GT/s and 16 GT/s data
rates used in lane equalization procedure.
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250328-preset_v6-v9-1-22cfa0490518@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Enable cpufreq on X1E80100 SoCs through the SCMI perf protocol node.
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Link: https://lore.kernel.org/r/20241030130840.2890904-3-quic_sibis@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add the cpucp mailbox and sram nodes required by SCMI perf protocol
on X1E80100 SoCs.
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Link: https://lore.kernel.org/r/20241030130840.2890904-2-quic_sibis@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Now that we have ACD support for GPU, add additional OPPs up to
Turbo L3 which are supported across all existing SKUs.
Signed-off-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Tested-by: Maya Matuszczyk <maccraft123mc@gmail.com>
Tested-by: Anthony Ruhier <aruhier@mailbox.org>
Acked-by: Bjorn Andersson <andersson@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/649354/
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Update GPU node to include acd level values.
Signed-off-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Tested-by: Maya Matuszczyk <maccraft123mc@gmail.com>
Tested-by: Anthony Ruhier <aruhier@mailbox.org>
Acked-by: Bjorn Andersson <andersson@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/649352/
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
According to documentation, the DBI range size is 0xf20. So fix it.
Cc: stable@vger.kernel.org # 6.14
Fixes: f8af195beeb0 ("arm64: dts: qcom: x1e80100: Add support for PCIe3 on x1e80100")
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250422-x1e80100-dts-fix-pcie3-dbi-size-v1-1-c197701fd7e4@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
WoA devices using x1e/x1p use android firmware to boot, which notably
includes Gunyah hypervisor. This means that, so far, Linux-based OS
could only boot in EL1 on those devices.
However Windows can replace Gunyah upon boot with it's own hypervisor,
and with the use of tools such as "slbounce", it's possible to do the
same for Linux-based OS, in which case some modifications to the DT are
necessary to facilitate the absence of Gunyah services.
Add a EL2-specific DT overlay and apply it to x1e/x1p WoA devices to
create -el2.dtb for each of them alongside "normal" dtb.
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20250503-sc-el2-overlays-v2-5-24e9b4572e15@trvn.ru
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
x1e80100 has an SMMUv3 connected to PCIe which is normally controlled by
Gunyah and is thus transparent to the OS. However if we boot Linux in
EL2, without Gunyah, we need to manage this IOMMU ourselves. To make
that easier, and since the hardware actually exists, just not "usually"
managed by Linux, describe it in the dts as "reserved".
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20250503-sc-el2-overlays-v2-4-24e9b4572e15@trvn.ru
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
There are currently two passive trip points defined for the CPU, but no
cooling devices are attached to the thermal zones. We don't have support
for cpufreq upstream yet, but actually this is redundant anyway because the
CPU is throttled automatically when reaching high temperatures.
Drop the passive trip points and keep just the critical shutdown as safety
measure in case the throttling fails.
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20250219-x1e80100-thermal-fixes-v1-4-d110e44ac3f9@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Unlike the CPU, the GPU does not throttle its speed automatically when it
reaches high temperatures. With certain high GPU loads it is possible to
reach the critical hardware shutdown temperature of 120°C, endangering the
hardware and making it impossible to run certain applications.
Set up GPU cooling similar to the ACPI tables, by throttling the GPU speed
when reaching 95°C and polling every 200ms.
Cc: stable@vger.kernel.org
Fixes: 721e38301b79 ("arm64: dts: qcom: x1e80100: Add gpu support")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250219-x1e80100-thermal-fixes-v1-3-d110e44ac3f9@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The firmware configures the TSENS controller with a maximum temperature of
120°C. When reaching that temperature, the hardware automatically triggers
a reset of the entire platform. Some of the thermal zones in x1e80100.dtsi
use a critical trip point of 125°C. It's impossible to reach those.
It's preferable to shut down the system cleanly before reaching the
hardware trip point. Make the critical temperature trip points consistent
by setting all of them to 115°C and apply a consistent hysteresis.
The ACPI tables also specify 115°C as critical shutdown temperature.
Cc: stable@vger.kernel.org
Fixes: 4e915987ff5b ("arm64: dts: qcom: x1e80100: Enable tsens and thermal zone nodes")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250219-x1e80100-thermal-fixes-v1-2-d110e44ac3f9@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
A passive trip point at 125°C is pretty high, this is usually the
temperature for the critical shutdown trip point. Also, we don't have any
passive cooling devices attached to the video thermal zone.
Change this to be a critical trip point, and add a "hot" trip point at
90°C for consistency with the other thermal zones.
Cc: stable@vger.kernel.org
Fixes: 4e915987ff5b ("arm64: dts: qcom: x1e80100: Enable tsens and thermal zone nodes")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250219-x1e80100-thermal-fixes-v1-1-d110e44ac3f9@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The X1 family is split into two parts: the 10- and 12-core parts are
variants of the same silicon with different fusing, whereas the 8-core
ones are a separate design. Thankfully, the software interface is only
barely different, letting us reuse much of the existing X1 work.
Introduce support for the X1P42100 SoC and the CRD based on it, through
overlaying some bits. Everything we already support on X1E80100 and
friends, minus the GPU, should work as-is.
Tested-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250203-topic-x1p4_dts-v2-6-72cd4cdc767b@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Certain X1 SKUs vary very noticeably, but the CRDs based on them don't.
Commonize the existing X1E80100 DTSI to allow reuse.
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250203-topic-x1p4_dts-v2-5-72cd4cdc767b@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Asserting the NOCSR reset line keeps the PHY registers in tact.
This allows us to avoid programming long tables of magic values in the
operating system.
Wire up these resets to PCIe PHY4 and 5 (it's there on the others).
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250203-topic-x1p4_dts-v2-4-72cd4cdc767b@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Make this USB controller consistent with the others on this platform.
Fixes: 4af46b7bd66f ("arm64: dts: qcom: x1e80100: Add USB nodes")
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250109205232.92336-1-kettenis@openbsd.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The X Elite implements Server Base System Architecture (SBSA) specification
compliant generic watchdog.
Describe it.
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20250212-x1e80100-add-watchdog-v2-1-a73897f0dad5@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
There is no use wasting power on keeping the links between the CPU and
something else online when the CPUs are online. Change the interconnect
tag for such paths, so that RPMh is requested to automatically
clock-gate those when possible.
Keeping these paths online is also a potential power collapse blocker,
however this commit alone doesn't magically fix all the remaining
TODOs related to suspend.
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250111-topic-x1e_fixups-v1-2-77dc39237c12@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Pull SoC devicetree updates from Arnd Bergmann:
"We see the addition of eleven new SoCs, including a total of sixx
arm64 chips from Qualcomm alone. Overall, the Qualcomm platforms once
again make up the majority of all changes, after a couple of quieter
releases.
The new SoCs in this branch are:
- Microchip sama7d65 is a new 32-bit embedded chip with a single
Cortex-A7 and the current high end of the old Atmel SoC line.
- Samsung Exynos 9810 is a mobile phone chip used in some older
phones like the Samsung Galaxy S9
- Renesas R-Car V4H ES3.0 (R8A779G3) is an updated version of the V4H
(R8A779G0) low-power automotive SoC
- Renesas RZ/G3E (R0A09G047) is a family of embedded chips using
Cortex-A55 cores
- Qualcomm Snapdragon 8 Elite (SM8750) is a new phone chip based on
Qualcomm's Oryon CPU cores.
- Qualcomm Snapdragon AR2 (SAR2130P) is a SoC for augmented reality
glasses.
- Qualcomm IQ6 (QCS610) and IQ8 (QCS8300) are two industrial IOT
platforms.
- Snapdragon 425 (MSM8917) is a mobile phone SoC from 2016
- Qualcomm IPQ5424 is a Wi-Fi 7 networking chip
All of the above are part of already supported SoC families that only
need new devicetree files. Two additional SoCs in new families are
part of a separate branch.
There are 48 new machines in total, including six arm32 ones based on
aspeed. broadcom, microchip and st SoCs all using Cortex-A7 cores, and
a single risc-v board, the Banana Pi R3.
The remaining ones use arm64 chips from Broadcom, Samsung, NXP,
Mediatek, Qualcomm, Renesas and Rockchips and cover development
boards, phones, laptops, industrial machines routers.
A lot of ongoing work is for cleaning up build time warnings and other
issues, in addition to the new machines and added features"
* tag 'soc-dt-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (619 commits)
arm64: tegra: Fix Tegra234 PCIe interrupt-map
arm64: dts: qcom: x1e80100-romulus: Update firmware nodes
arm64: dts: rockchip: add DTs for Firefly ITX-3588J and its Core-3588J SoM
dt-bindings: arm: rockchip: Add Firefly ITX-3588J board
arm64: dts: rockchip: Add Orange Pi 5 Max board
dt-bindings: arm: rockchip: Add Xunlong Orange Pi 5 Max
arm64: dts: rockchip: refactor common rk3588-orangepi-5.dtsi
arm64: dts: rockchip: add WLAN to rk3588-evb1 controller
arm64: dts: rockchip: increase gmac rx_delay on rk3399-puma
arm64: dts: rockchip: Delete redundant RK3328 GMAC stability fixes
arm64: tegra: Disable Tegra234 sce-fabric node
arm64: tegra: Fix typo in Tegra234 dce-fabric compatible
arm64: tegra: Fix DMA ID for SPI2
arm64: dts: qcom: msm8916-samsung-serranove: Add display panel
arm64: dts: qcom: sm8650: Add 'global' interrupt to the PCIe RC nodes
arm64: dts: qcom: sm8550: Add 'global' interrupt to the PCIe RC nodes
arm64: dts: qcom: Remove unused and undocumented properties
arm64: dts: qcom: sdm450-lenovo-tbx605f: add DSI panel nodes
arm64: dts: qcom: pmi8950: add LAB-IBB nodes
arm64: dts: qcom: ipq5424: enable the download mode support
...
|
|
Back when the CRD support was brought up, the usb_2 controller didn't
have anything connected to it in order to test it properly, so it was
never enabled.
On the Lenovo ThinkPad T14s, the usb_2 controller has the fingerprint
controller connected to it. So enabling it, proved that the interrupts
lines were wrong from the start.
Fix both the pwr_event and the DWC ctrl_irq lines, according to
documentation.
Fixes: 4af46b7bd66f ("arm64: dts: qcom: x1e80100: Add USB nodes")
Cc: stable@vger.kernel.org # 6.9
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20250107-x1e80100-fix-usb2-controller-irqs-v1-1-4689aa9852a7@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add following coresight components for x1e80100 platform.
It includes CTI, dummy sink, dynamic Funnel, Replicator, STM,
TPDM, TPDA and TMC ETF.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Tested-by: Yushan Li <quic_yushli@quicinc.com>
Signed-off-by: Jie Gan <quic_jiegan@quicinc.com>
Link: https://lore.kernel.org/r/20241205054904.535465-1-quic_jiegan@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The address space in CDSP PAS (Peripheral Authentication Service)
remoteproc node should point to the QDSP PUB address space
(QDSP6...SS_PUB) which has a length of 0x10000. Value of 0x1400000 was
copied from older DTS, but it does not look accurate at all.
This should have no functional impact on Linux users, because PAS loader
does not use this address space at all.
Fixes: 5f2a9cd4b104 ("arm64: dts: qcom: x1e80100: Add ADSP/CDSP remoteproc nodes")
Cc: stable@vger.kernel.org
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241213-dts-qcom-cdsp-mpss-base-address-v3-14-2e0036fccd8d@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The address space in ADSP PAS (Peripheral Authentication Service)
remoteproc node should point to the QDSP PUB address space
(QDSP6...SS_PUB): 0x0680_0000 with length of 0x10000.
0x3000_0000, value used so far, is the main region of CDSP and was
simply copied from other/older DTS.
Correct the base address and length, which also moves the node to
different place to keep things sorted by unit address. The diff looks
big, but only the unit address and "reg" property were changed. This
should have no functional impact on Linux users, because PAS loader does
not use this address space at all.
Fixes: 5f2a9cd4b104 ("arm64: dts: qcom: x1e80100: Add ADSP/CDSP remoteproc nodes")
Cc: stable@vger.kernel.org
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241213-dts-qcom-cdsp-mpss-base-address-v3-13-2e0036fccd8d@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Disable U1 and U2 power-saving states to improve stability of USB.
These low-power link states, designed to reduce power consumption
during idle periods, can cause issues in latency-sensitive or high
throughput use cases. Over the years, some of the issues seen are
as follows:
1. In device mode of operation, when UVC is active, enabling U1/U2
is sometimes causing packets drops due to delay in entry/exit of
intermittent these low power states. These packet drops are often
reflected as missed isochronous transfers, as the controller wasn't
able to send packet in that microframe interval and hence glitches
are seen on the final transmitted video output.
2. On QCS6490-Rb3Gen2 Vision kit, ADB connection is heavily unstable
when U1/U2 is enabled. Often when link enters U2, there is a re-
enumeration seen and device is unusable for many use cases.
3. On QCS8300/QCS9100, it is observed that when Link enters U2, when
the cable is disconnected and reconnected to host PC in HS, there
is no link status change interrupt seen and the plug-in in HS doesn't
show up a bus reset and enumeration failure happens.
Disabling these intermittent power states enhances device stability
without affecting power usage.
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241231081115.3149850-15-quic_prashk@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The CPU-to-SDHC interconnect path for the SDHC_2 needs to have the
active-only tags. The tags are missing entirely on for the SDHC_4
controller interconnect paths.
Fix all tags for both controllers.
Fixes: ffb21c1e19b1 ("arm64: dts: qcom: x1e80100: Describe the SDHC controllers")
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20241227-b4-x1e80100-qcp-sdhc-fixes-v1-1-cd971f7f0955@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The X1E80100 platform uses PMK8550 to provide sleep clock. According to the
documentation, that clock has 32.7645 kHz frequency. Correct the sleep
clock definition.
Fixes: af16b00578a7 ("arm64: dts: qcom: Add base X1E80100 dtsi and the QCP dts")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241224-fix-board-clocks-v3-18-e9b08fbeadd3@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add the uart14 instance for X1E80100 (typically used for Bluetooth).
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241007-x1e80100-pwrseq-qcp-v1-2-f7166510ab17@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add the power domains and OPP tables to all the QUP-related UART/I2C/SPI
nodes to ensure that we vote for the necessary performance states. Similar
to sm8350.dtsi, the OPPs depend on the QUP instance. The first two
instances in each geniqup group need &rpmhpd_opp_svs starting at 120MHz,
the others already starting at 100MHz. I2C always runs at a lower clock
frequency and therefore uses a fixed vote.
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241007-x1e80100-pwrseq-qcp-v1-1-f7166510ab17@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The X Elite platform features two SDHC v5 controllers.
Describe the controllers along with the pin configuration in TLMM
for the SDC2, since they are hardwired and cannot be muxed to any
other function. The SDC4 pin configuration can be muxed to different
functions, so leave those to board specific dts.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20241212-x1e80100-qcp-sdhc-v4-1-a74c48ee68a3@linaro.org
[bjorn: Replaced 0s with QCOM_ICC_TAG_ALWAYS]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
This reverts commit f042bc234c2e00764b8aa2c9e2f8177cdc63f664.
A recent change enabling role switching for the x1e80100 USB-C
controllers breaks UCSI and DisplayPort Alternate Mode when the
controllers are in host mode:
ucsi_glink.pmic_glink_ucsi pmic_glink.ucsi.0: PPM init failed, stop trying
As enabling OTG mode currently breaks SuperSpeed hotplug and suspend,
and with retimer (and orientation detection) support not even merged
yet, let's revert at least until we have stable host mode in mainline.
Fixes: f042bc234c2e ("arm64: dts: qcom: x1e80100: enable OTG on USB-C controllers")
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/all/hw2pdof4ajadjsjrb44f2q4cz4yh5qcqz5d3l7gjt2koycqs3k@xx5xvd26uyef
Link: https://lore.kernel.org/lkml/Z1gbyXk-SktGjL6-@hovoldconsulting.com/
Cc: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20241210111444.26240-4-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
As per memory map table, the region for PCIe6a is 64MByte. Hence, set the
size of 32 bit non-prefetchable memory region beginning on address
0x70300000 as 0x3d00000 so that BAR space assigned to BAR registers can be
allocated from 0x70300000 to 0x74000000.
Fixes: 7af141850012 ("arm64: dts: qcom: x1e80100: Fix up BAR spaces")
Cc: stable@vger.kernel.org
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241113080508.3458849-1-quic_qianyu@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Merge the arm64-for-6.13 branch into arm64-for-6.14, to carry forward
the commits that were picked up late in the cycle but didn't make it
into a pull request.
|
|
Pull SoC devicetree updates from Arnd Bergmann:
"This release adds the devicetree files for an impressive number of new
SoC variants, though as expected these are all related to others we
already support:
- The microchip sam9x7 devicetree is now added, after the device
driver and platform code has already made it in. This is likely the
last ARMv5 (!) platform to ever get added, updating the 20+ year
old at91/sam9 platform with DDR3 memory and gigabit ethernet.
- On the Apple platform, there are now devicetree files for a number
of A-series SoCs in addition to the M-series ones, these are used
primarily in phones and tablets, but are closely related to the
already supported chips.
- Samsung Exynos 8895 and Exynos 990 are more phone SoCs used in
older Samsung Galaxy phones.
- Qualcomm Snapdragon 778G (SM7325) is another phone SoC, closely
related to the Snapdragon 7c+ Gen 3 (SC7280) used in low-end
laptops.
- Rockchip RK3528 and RK3576 are new variants of their TV box and
Tablet chips, still using the older ARMv8.0 cores from
RK3328/RK3399 but with a newer process and other improvements from
the RK35xx (otherwise ARMv8.2) chips. RK3566T and RK3399-S are also
added, these are just lower-cost versions of their normal
counterparts.
- TI J742S2 is a feature-reduced version of the J784s4
industrial/automotive SoC, with fewer CPU cores.
- Sophgo SG2002 is an embedded SoC with one RISC-V (C906) and one ARM
(Cortex-A53) core, at this point support is only added for running
on the RISC-V side on the LicheeRV Nano board.
A total of 92 new .dts files describing individual machines is added,
which must be a new record. The majority of these is for the newly
added chips above, notably all the Apple phones and tablets. The other
new machines include nine industrial/embedded boards with NXP i.MX6 or
i.MX8 SoCs, eight for Rockchips RK35XX and one or two each for
Rockchips RV1109, RK3308, Allwinner A33, Tegra 234, Qualcomm
qcs9100/sc8280xp/x1e80100, TI AM625 and Starfive JH7110.
As usual there are also many newly added features in existing boards
as well as cleanups and minor bugfixes"
* tag 'soc-dt-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (718 commits)
arm64: dts: apm: Remove unused and undocumented "bus_num" property
arm: dts: spear13xx: Remove unused and undocumented "pl022,slave-tx-disable" property
arm64: dts: amd: Remove unused and undocumented "amd,zlib-support" property
arm64: dts: lg131x: Update spi clock properties
arm64: dts: seattle: Update spi clock properties
arm64: dts: rockchip: use less broad pinctrl for pcie3x1 on Radxa E25
arm64: dts: rockchip: add Radxa ROCK 5C
dt-bindings: arm: rockchip: add Radxa ROCK 5C
arm64: dts: rockchip: orangepi-5-plus: Enable GPU
arm64: dts: rockchip: enable USB3 on NanoPC-T6
arm64: dts: rockchip: adapt regulator nodenames to preferred form
arm64: dts: rockchip: Enable HDMI display for rk3588 Cool Pi GenBook
arm64: dts: rockchip: Enable HDMI display for rk3588 Cool Pi 4B
arm64: dts: rockchip: Enable HDMI0 for rk3588 Cool Pi CM5 EVB
arm64: dts: rockchip: Enable HDMI on NanoPi R6C/R6S
arm64: dts: rockchip: Enable GPU on NanoPi R6C/R6S
arm64: dts: rockchip: Enable HDMI on Hardkernel ODROID-M2
arm64: dts: rockchip: Remove non-removable flag from sdmmc on rk3576-sige5
arm64: dts: allwinner: a100: perf1: Add eMMC and MMC node
arm64: dts: allwinner: pinephone: Add mount matrix to accelerometer
...
|
|
Describe PCIe3 controller and PHY. Also add required system resources like
regulators, clocks, interrupts and registers configuration for PCIe3.
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241105073615.3076979-1-quic_qianyu@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Update the numbers based on the information found in the DSDT.
Fixes: af16b00578a7 ("arm64: dts: qcom: Add base X1E80100 dtsi and the QCP dts")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240716-topic-h_bits-v1-2-f6c5d3ff982c@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The fifth PCIe controller is connected to the PCIe North ANoC.
Fix the corresponding interconnect property so that the OS manages the
right path.
Fixes: 62ab23e15508 ("arm64: dts: qcom: x1e80100: add PCIe5 nodes")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241024131101.13587-3-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The fourth PCIe controller is connected to the PCIe North ANoC.
Fix the corresponding interconnect property so that the OS manages the
right path.
Fixes: 5eb83fc10289 ("arm64: dts: qcom: x1e80100: Add PCIe nodes")
Cc: stable@vger.kernel.org # 6.9
Cc: Abel Vesa <abel.vesa@linaro.org>
Cc: Sibi Sankar <quic_sibis@quicinc.com>
Cc: Rajendra Nayak <quic_rjendra@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241024131101.13587-2-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The 32-bit BAR spaces are reaching outside their assigned register
regions. Shrink them to match their actual sizes.
This resolves an issue where the regions overlap and one of the
controllers won't come up, which can be seen in the log as:
qcom-pcie 1c08000.pci: resource collision: [mem 0x7c300000-0x7fffffff] conflicts with 1c00000.pci dbi [mem 0x7e000000-0x7e000f1c]
While at it, unify the style.
Fixes: 5eb83fc10289 ("arm64: dts: qcom: x1e80100: Add PCIe nodes")
Cc: stable@vger.kernel.org
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240710-topic-barman-v1-1-5f63fca8d0fc@linaro.org
[bjorn: Added note about overlapping resource regions]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
DTS coding style expects labels to be lowercase. No functional impact.
Verified with comparing decompiled DTB (dtx_diff and fdtdump+diff).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241022-dts-qcom-label-v3-17-0505bc7d2c56@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Resize the GICR register region as it currently seeps into the CPU Control
Processor mailbox RX region.
Fixes: af16b00578a7 ("arm64: dts: qcom: Add base X1E80100 dtsi and the QCP dts")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Link: https://lore.kernel.org/r/20240612124056.39230-4-quic_sibis@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Fix the description and compatible for PCIe 6a, as it is in fact a
4-lanes controller and PHY, but it can also be used in 2-lanes mode. For
4-lanes mode, it uses the lanes provided by PCIe 6b. For 2-lanes mode,
PCIe 6a uses 2 lanes and then PCIe 6b uses the other 2 lanes. The number
of lanes in which the PHY should be configured depends on a TCSR register
value on each individual board.
Cc: stable+noautosel@kernel.org # Depends on pcie-qcom 16.0 GT/s support
Fixes: 5eb83fc10289 ("arm64: dts: qcom: x1e80100: Add PCIe nodes")
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241009-x1e80100-dts-fixes-pcie6a-v3-1-14a1163e691b@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
These 3 controllers support OTG and the driver requires the usb-role-switch
property to enable OTG. Add the property to enable OTG by default.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241011231624.30628-1-jonathan@marek.ca
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add missing Broadcast_AND region to the LLCC block for x1e80100,
as the LLCC version on this platform is 4.1 and it provides the region.
This also fixes the following error caused by the missing region:
[ 3.797768] qcom-llcc 25000000.system-cache-controller: error -EINVAL: invalid resource (null)
This error started showing up only after the new regmap region called
Broadcast_AND that has been added to the llcc-qcom driver.
Cc: stable@vger.kernel.org # 6.11: 055afc34fd21: soc: qcom: llcc: Add regmap for Broadcast_AND region
Fixes: af16b00578a7 ("arm64: dts: qcom: Add base X1E80100 dtsi and the QCP dts")
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20241014-x1e80100-dts-llcc-add-broadcastand_region-v2-1-5ee6ac128627@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
"idle-state-name" is not a valid property for "domain-idle-state"
binding, so drop it.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20241014161631.1527918-2-robh@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The DWC PCIe controller can be used with its internal MSI controller or
with an external one such as the GICv3 Interrupt Translation Service
(ITS).
Add the msi-map properties needed to use the GIC ITS. This will also
make Linux switch to the ITS implementation, which allows for assigning
affinity to individual MSIs. This specifically allows NVMe and Wi-Fi
interrupts to be processed on all cores (and not just on CPU0).
Note that using the GIC ITS on x1e80100 will cause Advanced Error
Reporting (AER) interrupts to be received on errors unlike when using
the internal MSI controller. Consequently, notifications about
(correctable) errors may now be logged for errors that previously went
unnoticed.
Also note that PCIe5 (and PCIe3) can currently only be used with the
internal MSI controller due to a platform (firmware) limitation.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20241009161715.14994-1-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The DTS code coding style expects exactly one space around '='
character.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konradybcio@kernel.org>
Link: https://lore.kernel.org/r/20240905-dts-cleanup-v1-4-f4c5f7b2c8c2@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Describe the TCSR download mode register to enable download mode
control.
This specifically allows the OS to disable download mode in case the
boot firmware has left it enabled to avoid entering the crash dump mode
after a hypervisor reset by default.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20241002100122.18809-3-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add the missing clkref enable and pipediv2 clocks to the PCIe5 PHY.
Fixes: 62ab23e15508 ("arm64: dts: qcom: x1e80100: add PCIe5 nodes")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konradybcio@kernel.org>
Link: https://lore.kernel.org/r/20240916082307.29393-4-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add the missing clkref enable and pipediv2 clocks to the PCIe4 and
PCIe6a PHYs.
Fixes: 5eb83fc10289 ("arm64: dts: qcom: x1e80100: Add PCIe nodes")
Cc: stable@vger.kernel.org # 6.9
Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Konrad Dybcio <konradybcio@kernel.org>
Link: https://lore.kernel.org/r/20240916082307.29393-3-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
