Age | Commit message (Collapse) | Author |
|
Pinebook has an RTL8723CS WiFi + BT chip. BT is connected to UART1
and uses PL5 as device wake GPIO and PL6 as host wake GPIO.
Enable it in the device tree.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Bastian Germann <bage@debian.org>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20221105153319.19345-2-bage@debian.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
|
|
The node names should be generic and DT schema expects certain pattern
(e.g. with key/button/switch).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220609113911.380368-4-krzysztof.kozlowski@linaro.org
|
|
A new 'chassis-type' root node property has recently been approved for
the device-tree specification, in order to provide a simple way for
userspace to detect the device form factor and adjust their behavior
accordingly.
This patch fills in this property for end-user devices (such as laptops,
smartphones and tablets) based on Allwinner ARM64 processors.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20211016102025.23346-2-arnaud.ferraris@collabora.com
|
|
The binding of R_INTC was updated to allow specifying interrupts other
than the external NMI, since routing those interrupts through the R_INTC
driver allows using them for wakeup.
Update the device trees to use the new binding.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
In contrast to the H6 (and later) manuals, the A64 datasheet does not
specify any limitations in the maximum possible frequency for eMMC
controllers.
However experimentation has found that a 150 MHz limit similar to other
SoCs and also the MMC0 and MMC1 controllers on the A64 seems to exist
for the MMC2 controller.
Limit the frequency for the MMC2 controller to 150 MHz in the SoC .dtsi.
The Pinebook seems to be the an odd exception, since it apparently seems
to work with 200 MHz as well, so overwrite this in its board .dts file.
Tested on a Pine64-LTS: 200 MHz HS-200 fails, 150 MHz HS-200 works.
Fixes: 22be992faea7 ("arm64: allwinner: a64: Increase the MMC max frequency")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-7-andre.przywara@arm.com
|
|
In recent Allwinner SoCs the first USB host controller (HCI0) shares
the first PHY with the MUSB controller. Probably to make this sharing
work, we were avoiding to declare this in the DT. This has two
shortcomings:
- U-Boot (which uses the same .dts) cannot use this port in host mode
without a PHY linked, so we were loosing one USB port there.
- It requires the MUSB driver to be enabled and loaded, although we
don't actually use it.
To avoid those issues, let's add this PHY link to the A64 .dtsi file.
After all PHY port 0 *is* connected to HCI0, so we should describe
it as this. Remove the part from the Pinebook DTS which already had
this property.
This makes it work in U-Boot, also improves compatiblity when no MUSB
driver is loaded (for instance in distribution installers).
Fixes: dc03a047df1d ("arm64: allwinner: a64: add EHCI0/OHCI0 nodes to A64 DTSI")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-2-andre.przywara@arm.com
|
|
The sun8i-codec driver introduced a new set of DAPM widgets that more
accurately describe the hardware topology. Update the various device
trees to use the new widget names.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200726012557.38282-7-samuel@sholland.org
|
|
Pinebook has an ANX6345 bridge connected to the RGB666 LCD output and
eDP panel input. The bridge is controlled via I2C that's connected to
R_I2C bus.
Enable all this hardware in device tree.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
The Pinebook does not use the CSI bus on the A64. In fact it does not
use GPIO port E for anything at all. Thus the following regulators are
not used and do not need voltages set:
- ALDO1: Connected to VCC-PE only
- DLDO3: Not connected
- ELDO3: Not connected
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
Now that AXP803 GPIO support is available, we can properly model
the hardware. Replace the use of GPIO0-LDO with a fixed regulator
controlled by GPIO0. This boost regulator is used to power the
(internal and external) USB ports, as well as the speakers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
The output from the backlight regulator is labeled as "VBKLT" in the
schematic. Using the equation and resistor values from the schematic,
the output is approximately 18V, not 3.3V. Since the regulator in use
(SS6640STR) is a boost regulator powered by PS (battery or AC input),
which are both >3.3V, the output could not be 3.3V anyway.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
Allwinner A64 SoC has separate supplies for PC, PD, PE, PG and PL.
VCC-PC and VCC-PG are supplied by ELDO1 at 1.8v.
VCC-PD is supplied by DCDC1 (VCC-IO) at 3.3v.
VCC-PE is supplied by ALDO1, and is unused.
VCC-PL creates a circular dependency, so it is omitted for now.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
Normally GPIO pin references are followed by a comment giving the pin
name for searchability. Add the comment here where it was missing.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
Boards generally reference the simplefb nodes from the SoC dtsi by
label, not by full path. simplefb_hdmi is already like this in the
Pinebook DTS. Update simplefb_lcd to match.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
The r_i2c node should come before r_rsb, and in any case should not
separate the axp803 node from its subnodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
This fixed regulator has no consumers, GPIOs, or other connections.
Remove it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
Add CPU regulator and operating points for all the A64-based boards
that are currently supported to enable DVFS.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
By default, gpio-keys configures the pin to trigger wakeup IRQs on
either edge. The lid switch should only trigger wakeup when opening the
lid, not when closing it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
Allwinner device tree files used different comment style for
copyright notice.
Update this to keep a coherency.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
This reverts commits 3d109bdca981 ("ARM: dts: sunxi: Remove useless
phy-names from EHCI and OHCI"), 0a3df8bb6dad ("ARM: dts: sunxi: h3/h5:
Remove useless phy-names from EHCI and OHCI") and 3c7ab90aaa28 ("arm64:
dts: allwinner: Remove useless phy-names from EHCI and OHCI").
It turns out that while the USB bindings were not mentionning it, the PHY
client bindings were mandating that phy-names is set when phys is. Let's
add it back.
Fixes: 3d109bdca981 ("ARM: dts: sunxi: Remove useless phy-names from EHCI and OHCI")
Fixes: 0a3df8bb6dad ("ARM: dts: sunxi: h3/h5: Remove useless phy-names from EHCI and OHCI")
Fixes: 3c7ab90aaa28 ("arm64: dts: allwinner: Remove useless phy-names from EHCI and OHCI")
Reported-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20191002112651.100504-1-mripard@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Allwinner arm64 DT changes for 5.2
Our usual bunch of patches, the most notable one being:
- Fixing the DTC warnings
- Fix DT bindings not being properly respected, thanks to the DT
validation
- New Board: Oceanic 5205, Beelink GS1, Orange Pi3
* tag 'sunxi-dt64-for-5.2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (22 commits)
arm64: dts: allwinner: a64-amarula-relic: Add OV5640 camera node
arm64: dts: allwinner: a64: Add pinmux setting for CSI MCLK on PE1
arm64: dts: allwinner: Fix DE2 bus node name
arm64: dts: allwinner: Remove useless phy-names from EHCI and OHCI
arm64: dts: allwinner: h6: Add MMC1 pins
arm64: dts: allwinner: h6: Add Orange Pi 3 DTS
arm64: dts: allwinner: h6: Introduce Beelink GS1 board
dt-bindings: vendor-prefixes: add AZW
arm64: dts: allwinner: h6: move MMC pinctrl to dtsi
arm64: dts: allwinner: h6: Add device node for SID
arm64: dts: allwinner: a64: Fix the Codec I2S binding
arm64: dts: allwinner: a64: Add default dr_mode
arm64: dts: allwinner: Fix pinctrl node names
arm64: dts: allwinner: a64: Add missing PIO clocks
arm64: dts: allwinner: a64: Fix display pipeline endpoints
arm64: dts: allwinner: a64: Fix the TCON output clock
arm64: dts: allwinner: h6: Add Video Engine node
arm64: dts: allwinner: a64: Add cross links for the mixers
arm64: allwinner: a64: Add Oceanic 5205 5inMFD initial support
dt-bindings: Add vendor prefix for oceanic
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Neither the OHCI or EHCI bindings are using the phy-names property, so we
can just drop it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The A64 datasheet lists the supply rail for the headphone amp's charge
pump as "CPVDD". cpvdd-supply is the name of the property for this power
rail specified in the device tree bindings. "HPVCC" was the name used in
the A33 datasheet for the same function.
Rename the supply so it matches the datasheet and bindings.
Fixes: c56689e6f2fb ("arm64: dts: allwinner: a64: bananapi-m64: Enable audio codec")
Fixes: 6de8e717848f ("arm64: dts: allwinner: a64: enable sound on Pinebook")
Fixes: 498c21f233ed ("arm64: dts: allwinner: a64: enable sound on Pine64 and SoPine")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
Pinebook has ACIN connector and 10000 mAh battery.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The Pinebook has a headphone jack tied to the HP headphone output of
the SoC, and internal speakers connected to the LINEOUT of the SoC,
through a standalone amplifier.
This commit enables I2S, digital and analog parts of audio codec on
Pinebook, along with a device node for the external amplifier.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
[wens@csie.org: dropped headphone_amp; added headphone amp regulator supply;
fixed speaker_amp node name and sound-name-prefix name]
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
Backlight power is controlled by PH6 GPIO, so add corresponding
regulator-fixed node for it. Otherwise backlight won't light up
if bootloader doesn't enable it.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The pinmux name and label for a specific function should denote which
pingroup it is on, or if there is only one option for the function, have
not enumerating prefix/suffix at all.
The "r_i2c_pins_a" label is renamed to "r_i2c_pl89_pins" to fit our
current style. The node name "i2c" is also changed to "r-i2c-pl89-pins"
to match. The reason for the peculiar name is that the other option for
muxing R_I2C is on the PL0/PL1 pins, so the name has to mention the pin
numbers in addition to the pingroup.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The pinmux name and label for a specific function should denote which
pingroup it is on, or if there is only one option for the function, have
not enumerating prefix/suffix at all.
The "uart0_pins_a" label is renamed to "uart0_pb_pins" to fit our
current style. The node name "uart0" is also changed to "uart0-pb-pins"
to match.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The eMMC 5.0 standard introduced the data strobe (DS) pin. This pin is
not used for pre-5.0 data modes, nor is it found on pre-5.0 eMMC chips.
On the A64, this pin is muxed with spi0's MISO pin. If the DS pin is
included in the mmc2 pinmux by default, this wil prevent the usage
of both mmc2 and spi0 together.
Instead, split out the DS pin to a separate pinmux that only gets used
by boards that actually have it wired up. Currently supported ones
include the Bananapi M64 and Pine64 Pinebook. These are fixed up.
Fixes: a3e8f4926248 ("arm64: allwinner: a64: Add MMC pinctrl nodes")
Fixes: b8bcf0e1b212 ("arm64: allwinner: add BananaPi-M64 support")
Fixes: df35fbcfa398 ("arm64: dts: allwinner: add support for Pinebook")
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
Another user of cd-inverted seems to have crept in. Switch it away from
cd-inverted to be consistent with other sunxi boards.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
On usual A64 board design the power of HDMI controller is connected to
DLDO1 of the AXP803 PMIC. If this regulator is shut down, the HDMI
output will be blank. Therefore the simplefb driver should keep this
regulator on.
Add the regulator to all currently available A64 boards' simplefb_hdmi
device node, if the board is capable of outputing HDMI.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Currently all ARM kernels will have s2idle enabled if CONFIG_SUSPEND is
present. In this case if the lid is closed, systemd-logind will enter
s2idle mode by default; however there's no possible wakeup source
defined, so the system will enter a forever idle.
Add the lid itself as a wakeup source, thus the system can wakeup when
the lid is opened.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Pinebook is a A64-based laptop produced by Pine64, with the following
peripherals:
USB:
- Two external USB ports (one is directly connected to A64's OTG
controller, the other is under a internal hub connected to the host-only
controller.)
- USB HID keyboard and touchpad connected to the internal hub.
- USB UVC camera connected to the internal hub.
Power-related:
- A DC IN jack connected to AXP803's DCIN pin.
- A Li-Polymer battery connected to AXP803's battery pins.
Storage:
- An eMMC by Foresee on the main board (in the product revision of the
main board it's designed to be switchable).
- An external MicroSD card slot.
Display:
- An eDP LCD panel (1366x768) connected via an ANX6345 RGB-eDP bridge.
- A mini HDMI port.
Misc:
- A Hall sensor designed to detect the status of lid, connected to GPIO PL12.
- A headphone jack connected to the SoC's internal codec.
- A debug UART port muxed with headphone jack.
This commit adds basical support for it.
[vasily: squashed several commits into one, added simplefb node, added usbphy
to ehci0 and ohci0 nodes and other cosmetic changes to dts]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|